CASCADE-MIB

All MIBs › CASCADE-MIB

Category: Vendor: Avaya

Description: Manages Cascade Communications (Ascend/Lucent) WAN ATM/Frame Relay switch configuration and circuit statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CASCADE-MIB?

CASCADE-MIB is a legacy Cascade Communications (enterprise OID 277, ATM/Frame Relay switch vendor, later Ascend/Lucent) proprietary MIB reporting network-node addressing and NMS-connectivity status. Its objects cover subnet mask, network number, DLCI address-signaling mode, max segment size, SMDS area-mask start/digits, an ASE (Address/Subnet Entry) table (address, mask, default gateway, metric type, admin status, ifIndex, DLCI), node IP/LAN-IP address, and an NMS table (index, IP address, node state, poll status, model, serial number). As a configuration/status MIB it lets an administrator confirm a Cascade switch node's addressing and NMS-poll reachability. It is deployed on legacy Cascade Communications ATM/Frame Relay switches. Engineers can download the CASCADE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CASCADE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Legacy Cascade Communications ATM/Frame Relay switches

Monitoring Examples

An administrator checks nodePollStatus and nodeState to confirm a Cascade switch node is reachable and healthy from the NMS.

What Can Be Monitored

node addressing and NMS-poll reachability

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
ifInErrors

OIDs

OID symbolic	OID numeric	Type	Access	Description
cascade	1.3.6.1.4.1.277
NTF nodeFileTransferReport	1.3.6.1.4.1.277.0.49			Reporting the outcome of a previous file transfer request. nodeFileTransferRequest specifies the request and nodeFileTransferStatus gives the outcome.
cascfr	1.3.6.1.4.1.277.1
NTF nodeBoardInserted	1.3.6.1.4.1.277.1.0.1			This trap indicates that a board has been inserted into the indicated slot.
NTF nodeBoardPulled	1.3.6.1.4.1.277.1.0.2			This trap indicates that a board has been pulled out from the indicated slot.
NTF nodeBoardMismatch	1.3.6.1.4.1.277.1.0.3			This trap indicates that the actual board type on the indicated slot is inconsistent with what is configured.
NTF nodePsAStatusChange	1.3.6.1.4.1.277.1.0.4			This trap indicates that the power supply A has changed state (toggled between up and down states).
NTF nodePsBStatusChange	1.3.6.1.4.1.277.1.0.5			This trap indicates that the power supply B has changed state (toggled between up and down states).
NTF nodeFanStatusChange	1.3.6.1.4.1.277.1.0.6			This trap indicates that a fan has changed state (toggled between up and down states).
NTF nodeSwDownloadComplete	1.3.6.1.4.1.277.1.0.7			This trap indicates that a software download was complete.
NTF nodeSwDownloadFailed	1.3.6.1.4.1.277.1.0.8			This trap indicates that a software download failed.
NTF nodePrDownloadComplete	1.3.6.1.4.1.277.1.0.9			This trap indicates that a PRAM download was complete.
NTF nodePrDownloadFailed	1.3.6.1.4.1.277.1.0.10			This trap indicates that a PRAM download failed.
NTF nodeTracefull	1.3.6.1.4.1.277.1.0.11			This trap indicates that the node trace table was full and has been copied to a TFTP buffer awaiting to be xfered to the NMS.
NTF nodeDiagLogfull	1.3.6.1.4.1.277.1.0.12			This trap indicates that the diagnostic log table was full and has been copied to a TFTP buffer awaiting to be xfered to the NMS.
NTF nodeFlashMemErr	1.3.6.1.4.1.277.1.0.13			This trap indicates that a checksum or CRC-32 error occurred in Flash.
NTF nodePramErr	1.3.6.1.4.1.277.1.0.14			This trap indicates that a checksum error or battery problem occurred in PRAM.
NTF nodeRamErr	1.3.6.1.4.1.277.1.0.15			This trap indicates that an I/O error occurred in DRAM or SRAM.
NTF nodeInternalErr	1.3.6.1.4.1.277.1.0.16			This trap indicates that a fatal internal hardware or software error encountered and system needs to be re-booted.
NTF pportStatusChange	1.3.6.1.4.1.277.1.0.17			This trap indicates that the indicated physical port has changed state.
NTF lportCongests	1.3.6.1.4.1.277.1.0.18			This trap indicates that the rate of entering severely and absolutely congested state on the indicated logical port has exceeded the threshold.
NTF trkStatusChange	1.3.6.1.4.1.277.1.0.19			This trap indicates that the trunk associated with the indicated logical port has changed state.
NTF cktDlciStatusChange	1.3.6.1.4.1.277.1.0.20			This trap indicates that the user-to-user PVC state has been changed for this virtual circuit. It has either been created or invalidated, or has toggled between the active and inactive states.
NTF cktDlciReroute	1.3.6.1.4.1.277.1.0.21			This trap indicates that a PVC has been re-routed.
NTF pportInterfaceMismatch	1.3.6.1.4.1.277.1.0.22			This trap indicates the actual physical interface is different than the configured physical interface.
NTF lportErrorExceedThreshold	1.3.6.1.4.1.277.1.0.23			This trap indicates the frame errors per minute on this lport exceeded the threshold.
NTF nodeErrorReport	1.3.6.1.4.1.277.1.0.24			A component in the switch discovered a non-fatal error condition.
NTF cktGrpStatusChange	1.3.6.1.4.1.277.1.0.25			Circuits on interfaces go up or down.
NTF nodeUserLogin	1.3.6.1.4.1.277.1.0.26			An user has logged in STDX through either serial console or telnet.
NTF nodeUserLogout	1.3.6.1.4.1.277.1.0.27			An user has logged out.
NTF cardUp	1.3.6.1.4.1.277.1.0.28			This trap indicates that an intelligent card has transitioned to an ACTIVE state.
NTF cardDown	1.3.6.1.4.1.277.1.0.29			This trap indicates that an intelligent card has transitioned to a NON-ACTIVE state.
NTF lnkStatusChange	1.3.6.1.4.1.277.1.0.30			This trap indicates that the link status (Link protocol) associated with the indicated logical port has changed state.
NTF lnkSmdsHbpNaTca	1.3.6.1.4.1.277.1.0.31			This trap indicates that non-Ack count for SMDS DXI heartbeat poll exceedes the threshold. The non-Ack count is reset every 15 minutes.
NTF lnkSmdsDiscardTca	1.3.6.1.4.1.277.1.0.32			This trap indicates that Total Discard packet count for SMDS packet exceedes the threshold. ( This trap has not been implemented in this release yet ).
NTF cardRedundSwitchOver	1.3.6.1.4.1.277.1.0.33			This trap indicates that the card in the specified slot has shot its active partner and has become the active card of the pair.
NTF cardErrorReport	1.3.6.1.4.1.277.1.0.34			The specified card discovered a non-fatal error condition.
NTF svcSetup	1.3.6.1.4.1.277.1.0.35			This trap is generated by the ingress switch whenever a Frame Relay Svc is setup or cleared. cktStatus indicates whether it is a setup or a clearing.
NTF svcClearing	1.3.6.1.4.1.277.1.0.36			Reserved for Frame Relay SVC.
NTF svcFailure	1.3.6.1.4.1.277.1.0.37			This trap is generated by the ingress switch whenever a Frame Relay svc setup fails. cktSvcCause contains the cause number.
NTF trkBuAttempt	1.3.6.1.4.1.277.1.0.38			This trap indicates that an attempt to establish the backup trunk associated with the indicated logical port is being made.
NTF trkBuFailure	1.3.6.1.4.1.277.1.0.39			This trap indicates that the primary trunk associated with the indicated logical port has not been backed up or the backup trunk associated with the indicated logical port has not been restored. The reason for failure is provided. The lportBuFailReason indicates the trunk type as follows: lportBuFailReson Trunk Type buTrkNotDef primary trunk buTrkNotEstab backup trunk
NTF trkBuReleased	1.3.6.1.4.1.277.1.0.40			This trap indicates that the backup trunk associated with the indicated logical port has been released.
NTF pportDS0LoopUpChange	1.3.6.1.4.1.277.1.0.41			This trap indicates one or more DS0's have gone into loopback.pportDS0LoopUpStatus reports the DS0's that have gone into loopback.
NTF pportDS0LoopDownChange	1.3.6.1.4.1.277.1.0.42			This trap indicates one or more DS0's have gone out of loopback.pportDS0LoopDownStatus reports the DS0's that have gone out of loopback.
NTF lportISDNCallRej	1.3.6.1.4.1.277.1.0.43			This trap indicates that a call has been rejected due either the inability to authenticate the call or lack of B-channel pool resources.
NTF pportdsx3LoopChange	1.3.6.1.4.1.277.1.0.44			This trap indicates when the DS3 or E3 has changed its current loopback state.
NTF pportds1LoopChange	1.3.6.1.4.1.277.1.0.45			This trap indicates when the DS1 has changed its current loopback state.
NTF pportExtClockBackup	1.3.6.1.4.1.277.1.0.46			This trap indicates that a pport has lost the external clock source and is switching over to the backup clock selected.
NTF pportExtClockRestore	1.3.6.1.4.1.277.1.0.47			This trap indicates that external clock is recovered and the pport will switch back to external clock.
NTF pportExtClkCapabilityMismatch	1.3.6.1.4.1.277.1.0.48			This trap indicates the port on this card (and the card itself) is not capable of running external clock.
NTF nodeBillingUsageRecOvflWarning	1.3.6.1.4.1.277.1.0.50			Warning that a usage record counter-value overflow condition has occurred while aggregating usage data recently collected from one or more IOPs. An overflow condition exists when an attempt was made to update a usage record counter, but such an update would have overflowed the counter. In this case, the usage record is closed and a new one is opened, if there is sufficient space in the service's aggregated usage data store.
NTF nodeBillingUsageRecCrFailed	1.3.6.1.4.1.277.1.0.51			Notification that a usage record could not be created.
NTF nodeBillingStateChange	1.3.6.1.4.1.277.1.0.52			Notification that billing has been enabled or disabled on the switch. This trap is generated at switch boot or when the value of the nodeBilling object is modified.
NTF lportBillingStateChange	1.3.6.1.4.1.277.1.0.53			Notification that billing has been enabled or disabled on a particular logical port. This trap is generated the value of the lportBilling is modified for a particular port; this trap IS NOT generated when the global nodeBilling is modified or when at switch boot.
NTF nodeBillingSwAPCommsFailure	1.3.6.1.4.1.277.1.0.54			Notification that switch to Adjunct Processor communication has failed and that a usage file transfer has failed to complete.
NTF lportCBRLineDataError	1.3.6.1.4.1.277.1.0.57			This trap indicates the error state of the CBR lport.
NTF clkSourceSwitch	1.3.6.1.4.1.277.1.0.58			This trap indicates that the CBR port switched its clock method.
NTF clkSourceFailure	1.3.6.1.4.1.277.1.0.59			This trap indicates that the clock generation unit switched between holdover mode and synchronization to reference clock.
NTF lportSmdsSip3SaNotFoundTca	1.3.6.1.4.1.277.1.0.60			This trap indicates that the number of Sa Not Found violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF lportSmdsSip3SaDaOnSamePortTca	1.3.6.1.4.1.277.1.0.61			This trap indicates that the number of Sa Da On Same Port violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF lportSmdsSip3DstGaNotFoundTca	1.3.6.1.4.1.277.1.0.62			This trap indicates that the number of Dst Ga Not Found violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF lportSmdsSip3DstIaScrnFailTca	1.3.6.1.4.1.277.1.0.63			This trap indicates that the number of Dst Ia Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF lportSmdsSip3SaValFailTca	1.3.6.1.4.1.277.1.0.64			This trap indicates that the number of Sa Val Fail violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF lportSmdsSip3DstIaNotFoundTca	1.3.6.1.4.1.277.1.0.65			This trap indicates that the number of Dst Ia Not Found violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF lportSmdsSip3SrcIaScrnFailTca	1.3.6.1.4.1.277.1.0.66			This trap indicates that the number of Src Ia Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF lportSmdsSip3DstGaScrnFailTca	1.3.6.1.4.1.277.1.0.67			This trap indicates that the number of Dst Ga Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF lportSmdsDxi2LinkIdInvalidTca	1.3.6.1.4.1.277.1.0.68			This trap indicates that the number of Link Id Invalid violations exceeded the specified Smds pdu violation threshold for the logical port.
NTF nodePrimarySyncReferenceChange	1.3.6.1.4.1.277.1.0.69			Notification that the Primary Synchronization Reference operational state has changed.
NTF nodeSecondarySyncReferenceChange	1.3.6.1.4.1.277.1.0.70			Notification that the Secondary Synchronization Reference operational state has changed.
NTF nodeExternalClockAChange	1.3.6.1.4.1.277.1.0.71			Notification that the External Reference Clock A operational state has changed.
NTF nodeExternalClockBChange	1.3.6.1.4.1.277.1.0.72			Notification that the External Reference Clock B operational state has changed.
NTF nodePortReferenceAChange	1.3.6.1.4.1.277.1.0.73			Notification that the Port Reference Clock A operational state has changed.
NTF nodePortReferenceBChange	1.3.6.1.4.1.277.1.0.74			Notification that the Port Reference Clock B operational state has changed.
NTF pportDS0InitiateLpbkFailure	1.3.6.1.4.1.277.1.0.75			This trap indicates that the DS0 requested to be set into far end loopback has failed to do so.
NTF pportDS0InitiateLpbkSuccess	1.3.6.1.4.1.277.1.0.76			This trap indicates that the DS0 requested to be set into far end loopback has succeeded.
NTF lportISDNIpAddrRej	1.3.6.1.4.1.277.1.0.77			This trap indicates that an Ip Address assignment failed.
NTF cktAtmStatusChange	1.3.6.1.4.1.277.1.0.78			This trap indicates that the user-to-user ATM PVC state has been changed for this virtual circuit. It has either been created or invalidated, or has toggled between the active and inactive states.
NTF cktAtmReroute	1.3.6.1.4.1.277.1.0.79			This trap indicates that an ATM PVC has been re-routed.
NTF cardTransmitClockStatusChange	1.3.6.1.4.1.277.1.0.80			This trap indicates the IOM transmit clock synchronization status has chnaged.
NTF cardSystemPrimaryClockStatusChange	1.3.6.1.4.1.277.1.0.81			This trap indicates that the IOM system primary clock reference status has changed.
NTF cardSystemSecondaryClockStatusChange	1.3.6.1.4.1.277.1.0.82			This trap indicates that the IOM system primary clock reference status has changed.
net	1.3.6.1.4.1.277.1.1
IP netMask	1.3.6.1.4.1.277.1.1.1	IpAddress	read-write	The IP subnet mask for the network. The default is 255.255.255.0 (class C) which allows 254 nodes.
IP netNumber	1.3.6.1.4.1.277.1.1.2	IpAddress	read-write	The IP network number for the network.
INT netDlciAddrSig	1.3.6.1.4.1.277.1.1.3	INTEGER	read-write	This variable states the DLCI addressing significance.
INT netMaxSegsize	1.3.6.1.4.1.277.1.1.4	INTEGER	read-write	This variable states the maximum sgement size for the network.
INT netSmdsAreaMaskStart	1.3.6.1.4.1.277.1.1.8	INTEGER	read-write	This variable states the starting digit number for defining the start of the Area Mask for SMDS Addresses.
INT netSmdsAreaMaskDigits	1.3.6.1.4.1.277.1.1.9	INTEGER	read-write	This variable states the number of digits used for defining the Area Mask for SMDS Addresses.
ase	1.3.6.1.4.1.277.1.2
aseTable	1.3.6.1.4.1.277.1.2.1		not-accessible	A list of ASE entries.
aseEntry	1.3.6.1.4.1.277.1.2.1.1		not-accessible	An ASE entry contains an external NMS path accessible from the node.
IP aseAddr	1.3.6.1.4.1.277.1.2.1.1.1	IpAddress	read-only	IP Address for an external NMS.
IP aseMask	1.3.6.1.4.1.277.1.2.1.1.2	IpAddress	read-only	IP Address mask for an external NMS. The default value is 255.255.255.255.
IP aseDefaultGwAddr	1.3.6.1.4.1.277.1.2.1.1.3	IpAddress	read-write	Default Gateway IP Address for reaching the external NMS. This field is not applicable to NMSs which are reachable via SLIP or on the same Ethernet.
INT aseMetricType	1.3.6.1.4.1.277.1.2.1.1.4	INTEGER	read-only	Type of metric (1 or 2) for each external NMS. The default is 1. (This field is not applicable to SLIP- based hosts.)
INT aseAdminStatus	1.3.6.1.4.1.277.1.2.1.1.5	INTEGER	read-write	The desired state of the entry.
IND aseIfIndex	1.3.6.1.4.1.277.1.2.1.1.6	Index	read-write	The interface value of the corresponding MIB-II ifEntry.
INT aseDlci	1.3.6.1.4.1.277.1.2.1.1.7	INTEGER	read-write	The management dlci through which the NMS communicates to the switch.
node	1.3.6.1.4.1.277.1.3
IP nodeIpAddr	1.3.6.1.4.1.277.1.3.1	IpAddress	read-write	The inband IP address of the node in the Cascade internal trunk IP network.
IP nodeLanIpAddr	1.3.6.1.4.1.277.1.3.2	IpAddress	read-write	The inband (Ethernet) IP address of the node for a NMS to access the node and the internal trunk IP network.
nodeNMSTable	1.3.6.1.4.1.277.1.3.3		not-accessible	A list of NMS entries.
nodeNMSEntry	1.3.6.1.4.1.277.1.3.3.1		not-accessible	A NMS entry contains an IP address of a NMS which has extended privilages.
IND nodeNMSIndex	1.3.6.1.4.1.277.1.3.3.1.1	Index	read-only	The IP address entry of a primary Network Management Station.
IP nodeNMSIpAddr	1.3.6.1.4.1.277.1.3.3.1.2	IpAddress	read-write	The IP address of the primary Network Management Station. It is to this address that Traps and TFTP requests will be directed.
INT nodeState	1.3.6.1.4.1.277.1.3.4	INTEGER	read-write	The state of the switch. The switch needs to await the state to be set to active before being fully operational after cold boot, when the NMS is reachable.
OCT nodePollStatus	1.3.6.1.4.1.277.1.3.5	OCTET STRING	read-only	The consolidated node status in response to keep-alive polls. It is an octet string of a proprietary format
STR nodeModel	1.3.6.1.4.1.277.1.3.6	DisplayString	read-only	The part number of the node.
OCT nodeSerial	1.3.6.1.4.1.277.1.3.7	OCTET STRING	read-only	The serial number (i.e., Ethernet Addr) of the switch.
STR nodeSwRev	1.3.6.1.4.1.277.1.3.8	DisplayString	read-only	The software revision number (major.minor).
STR nodeHwRev	1.3.6.1.4.1.277.1.3.9	DisplayString	read-only	The hardware revision number (major.minor).
STR nodeEpromRev	1.3.6.1.4.1.277.1.3.10	DisplayString	read-only	The EPROM firmware revision number (major.minor).
GAU nodeCpuUtil	1.3.6.1.4.1.277.1.3.11	Gauge	read-only	The CPU utilization percentage for packet processing.
INT nodePsAStatus	1.3.6.1.4.1.277.1.3.12	INTEGER	read-only	The status of the power supply A. For a detailed explanation for the power supply being either in the down or marginal state, refer to the nodePsADiagCode object.
INT nodePsBStatus	1.3.6.1.4.1.277.1.3.13	INTEGER	read-only	The status of the power supply B. For a detailed explanation for the power supply being either in the down or marginal state, refer to the nodePsBDiagCode object.
nodeFanTable	1.3.6.1.4.1.277.1.3.14		not-accessible	A list of fan entries.
nodeFanEntry	1.3.6.1.4.1.277.1.3.14.1		not-accessible	A Fan entry contains the status of a fan.
INT nodeFanIndex	1.3.6.1.4.1.277.1.3.14.1.1	INTEGER	read-only	A unique value for each fan.
INT nodeFanStatus	1.3.6.1.4.1.277.1.3.14.1.2	INTEGER	read-only	The status of the fan.
GAU nodeFanSpeed	1.3.6.1.4.1.277.1.3.14.1.3	Gauge	read-only	The speed in Revolutions Per. Minute (RPM) of the fan.
GAU nodeMemoryUtil	1.3.6.1.4.1.277.1.3.15	Gauge	read-only	The percentage of system memory utilization on this intelligent card.
GAU nodeMemoryUsage	1.3.6.1.4.1.277.1.3.16	Gauge	read-only	The system memory utilization, in terms of free bytes, for this intelligent card.
INT nodeMaxFramesize	1.3.6.1.4.1.277.1.3.17	INTEGER	read-only	The maximum frame size supported by the node. The default is 4096.
INT nodeQOSPollTimer	1.3.6.1.4.1.277.1.3.18	INTEGER	read-write	The timer (seconds) for generating QOS polling packets.
CTR nodeActivePvcs	1.3.6.1.4.1.277.1.3.19	Counter	read-only	The number of currently active PVCs on the node.
CTR nodeInactivePvcs	1.3.6.1.4.1.277.1.3.20	Counter	read-only	The number of currently inactive PVCs on the node.
CTR nodePendingPvcs	1.3.6.1.4.1.277.1.3.21	Counter	read-only	The number of currently call pending PVCs on the node.
CTR nodeInOctets	1.3.6.1.4.1.277.1.3.22	Counter	read-only	The total number of octets received on the node, including framing bytes.
CTR nodeInPkts	1.3.6.1.4.1.277.1.3.23	Counter	read-only	The total number of packets received on the node.
CTR nodeOutOctets	1.3.6.1.4.1.277.1.3.24	Counter	read-only	The total number of octets transmitted out of the node, including framing bytes.
CTR nodeOutPkts	1.3.6.1.4.1.277.1.3.25	Counter	read-only	The total number of packets requested to be transmitted out of the node, including those that were discarded or not sent.
STR nodeSwFilename	1.3.6.1.4.1.277.1.3.26	DisplayString	read-write	Name of the file to be downloaded.
INT nodeRebootAfterLoad	1.3.6.1.4.1.277.1.3.27	INTEGER	read-write	Instructs the device to either automatically reboot after the successful scheduled download or not.
TIK nodeSwToLoad	1.3.6.1.4.1.277.1.3.28	TimeTicks	read-write	Instructs the device to initiate a software download (via tftp) request to the master management station after the specified time ticks have elapsed.
INT nodeSwLoadState	1.3.6.1.4.1.277.1.3.29	INTEGER	read-write	The state of the software download request. A download which is in either the PENDING, ACTIVE or FAILED state can be terminated by setting this object to INACTIVE.
STR nodePrFilename	1.3.6.1.4.1.277.1.3.30	DisplayString	read-write	Name of the PRAM image file to be downloaded.
TIK nodePrToLoad	1.3.6.1.4.1.277.1.3.31	TimeTicks	read-write	Instructs the device to initiate a PRAM image file download (via tftp) request to the master management station after the specified time ticks have elapsed.
INT nodePrLoadState	1.3.6.1.4.1.277.1.3.32	INTEGER	read-write	The state of the PRAM download request. A download which is in either the PENDING, ACTIVE or FAILED state can be terminated by setting this object to INACTIVE.
TIK nodeToWarmboot	1.3.6.1.4.1.277.1.3.33	TimeTicks	read-write	Instructs the switch to initiate a system warm boot after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request.
TIK nodeToColdboot	1.3.6.1.4.1.277.1.3.34	TimeTicks	read-write	Instructs the switch to initiate a system cold boot after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request.
TIK nodeToRedundant	1.3.6.1.4.1.277.1.3.35	TimeTicks	read-write	If redundancy is configured, instructs the node acting as Backup to disable the Active node and take over as the Active node. The disabling is initiated after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled request.
IP nodeInitiateBulkStats	1.3.6.1.4.1.277.1.3.36	IpAddress	read-write	Initiates a Bulk Statistics poll and via TFTP, transfer the data to the specified IP address.
INT nodeDiagNonFatalSource	1.3.6.1.4.1.277.1.3.37	INTEGER	read-only	Source who reported last non-fatal error.
TIK nodeDiagNonFatalTime	1.3.6.1.4.1.277.1.3.38	TimeTicks	read-only	Time the last non-fatal error was reported.
INT nodeDiagNonFatalErrMajor	1.3.6.1.4.1.277.1.3.39	INTEGER	read-only	Major error code of last non-fatal error.
INT nodeDiagNonFatalErrMinor	1.3.6.1.4.1.277.1.3.40	INTEGER	read-only	Minor error code of last non-fatal error.
STR nodeDiagNonFatalStr	1.3.6.1.4.1.277.1.3.41	DisplayString	read-only	Ascii string describing last non-fatal error.
INT nodeDiagFatalSource	1.3.6.1.4.1.277.1.3.42	INTEGER	read-only	Source who reported last fatal error.
TIK nodeDiagFatalTime	1.3.6.1.4.1.277.1.3.43	TimeTicks	read-only	Time the last fatal error was reported.
INT nodeDiagFatalErrMajor	1.3.6.1.4.1.277.1.3.44	INTEGER	read-only	Major error code of last fatal error.
INT nodeDiagFatalErrMinor	1.3.6.1.4.1.277.1.3.45	INTEGER	read-only	Minor error code of last fatal error.
STR nodeDiagFatalStr	1.3.6.1.4.1.277.1.3.46	DisplayString	read-only	Ascii string describing last fatal error.
CTR nodeDiagFatalReboots	1.3.6.1.4.1.277.1.3.47	Counter	read-only	Number of times the switch has re-booted since last fatal error was reported.
INT nodeDiagFatalAddress	1.3.6.1.4.1.277.1.3.48	INTEGER	read-only	Address switch was executing when it encountered fatal error.
CTR nodeDiagBackgroundPasses	1.3.6.1.4.1.277.1.3.49	Counter	read-only	Number of passes made by the background diagnostics.
CTR nodeDiagBackgroundFailures	1.3.6.1.4.1.277.1.3.50	Counter	read-only	Number of failures discovered by background diagnostics.
CTR nodeDiagBackgroundSuccesses	1.3.6.1.4.1.277.1.3.51	Counter	read-only	Number of successful passes by background diagnostics.
INT nodeDiagLEDReset	1.3.6.1.4.1.277.1.3.52	INTEGER	read-write	Change the node state from marginal to active. Change the LED from yellow to green.
INT nodeDiagPowerExtensive	1.3.6.1.4.1.277.1.3.53	INTEGER	read-write	Should power on diagnostics do slower, extensive testing, or fast testing?
OCT nodePortPoll	1.3.6.1.4.1.277.1.3.54	OCTET STRING	read-only	The consolidated port status in response to keep-alive polls.
INT nodeMaxTelnetConsole	1.3.6.1.4.1.277.1.3.55	INTEGER	read-write	The number of concurrent telnet consoles allowed. The default is 2. The maximum is 5. Set it 0 to disable telnet access.
INT nodeConsoleTimeout	1.3.6.1.4.1.277.1.3.56	INTEGER	read-write	Idle-logoff timer in minutes. The default is 5 minutes, and the maximum can be set is 60 minutes. To disable idle-logout, set this to 0.
nodeConsoleTable	1.3.6.1.4.1.277.1.3.57		not-accessible	A list of active consoles on the node, logged in through telnet or serial port.
nodeConsoleEntry	1.3.6.1.4.1.277.1.3.57.1		not-accessible	Information of a console.
INT nodeConsoleIndex	1.3.6.1.4.1.277.1.3.57.1.1	INTEGER	read-only	A positive integer to identify a console
OCT nodeUserName	1.3.6.1.4.1.277.1.3.57.1.2	OCTET STRING	read-only	The login user name up to 31 characters. There is no validation of the name, i.e., any string is acceptable.
IP nodeUserFrom	1.3.6.1.4.1.277.1.3.57.1.3	IpAddress	read-only	The IP address from which the user logged in. 0.0.0.0 if the user logged in through serial port.
INT nodeConsoleAccessMode	1.3.6.1.4.1.277.1.3.57.1.4	INTEGER	read-only	The access mode of the console. By default, a user is in READ ONLY mode.
TIK nodeConsoleUptime	1.3.6.1.4.1.277.1.3.57.1.5	TimeTicks	read-only	How long the console has been active.
INT nodePsADiagCode	1.3.6.1.4.1.277.1.3.58	INTEGER	read-only	The failure code of the power supply A. A non-zero value indicates one or more failures. Refer to the hardware manual for a description of the failure code.
INT nodePsBDiagCode	1.3.6.1.4.1.277.1.3.59	INTEGER	read-only	The failure code of the power supply B. A non-zero value indicates one or more failures. Refer to the hardware manual for a description of the failure code.
GAU nodeFrameMemoryUtil	1.3.6.1.4.1.277.1.3.60	Gauge	read-only	The percentage of frame memory utilization on this intelligent card.
GAU nodeFrameMemoryUsage	1.3.6.1.4.1.277.1.3.61	Gauge	read-only	The frame memory utilization, in terms of free bytes, for this intelligent card.
INT nodeCapability	1.3.6.1.4.1.277.1.3.62	INTEGER	read-only	The capability of this node.
OCT nodeSvcLastCallFailure	1.3.6.1.4.1.277.1.3.63	OCTET STRING	read-only	A textual string describing the last call failure.
INT nodeRerouteDelay	1.3.6.1.4.1.277.1.3.64	INTEGER	read-write	The number of seconds delay between each reroute batch event.
INT nodeRerouteCount	1.3.6.1.4.1.277.1.3.65	INTEGER	read-write	The number of virtual circuits to request a reroute for duing a single reroute batch event.
STR nodeFileTransferRequest	1.3.6.1.4.1.277.1.3.66	DisplayString	read-write	This object is used to initiate file transfers to and from the switch. A management station can initiate a file transfer by settting this object of text string in the following format: operation filename time-to-wait target-host protocol where operation - [get \| put], filename - configuration.[card] time-to-wait - a number in seconds target-host - the IP address of target host protocol - [tftp \| ftp] Multiple transfers can be specified by repeating above with ';' between each transfer specifier. Examples: o get configuration.10 5 152.148.10.100 tftp will start a transfer of configuration information on card 10 to host 152.148.10.100 in 5 seconds. o put configuration.1 2 152.148.1.1 tftp ; get configuration.1 15 152.148.1.1 tftp will (1) transfer configuration.1 from 152.148.1.1 (2) transfer configuration.2 to 152.148.1.1 To cancel the transfer request, set this object to empty.
INT nodeFileTransferStatus	1.3.6.1.4.1.277.1.3.67	INTEGER	read-only	The status of the file tarnsfer.
TIK nodeTime	1.3.6.1.4.1.277.1.3.68	TimeTicks	read-write	The current wall-clock time that is set on the switch in Universal Coordinated Time (UCT). The value is the number of seconds since 00:00:00 UCT January 1, 1970.
IP nodeBillingAPAddress	1.3.6.1.4.1.277.1.3.69	IpAddress	read-write	The IP Address of the Adjunct Billing Processor that is servicing this switch.
STR nodeBillingAPUsername	1.3.6.1.4.1.277.1.3.70	DisplayString	read-write	The Username of the account on the Adjunct Billing Processor to which usage data will be transferred via FTP.
STR nodeBillingAPPassword	1.3.6.1.4.1.277.1.3.71	DisplayString	read-write	The Password corresponding to the account identified by nodeBillingAPUsername. A NULL string is returned when read.
CTR nodeBillingSwAPCommsFailures	1.3.6.1.4.1.277.1.3.72	Counter	read-write	The number of times that communication from the switch to the Adjunct Billing Processor has failed during the current aggregation period. A failure signifies failure of a file transfer operation to the Adjunct Processor.
nodeBillingTable	1.3.6.1.4.1.277.1.3.73		not-accessible	A table of Billing System managable objects, indexed by service.
nodeBillingEntry	1.3.6.1.4.1.277.1.3.73.1		not-accessible	A nodeBillingEntry contains a set of statistics that summarize the Billing System performance for a particular service.
INT nodeBillingService	1.3.6.1.4.1.277.1.3.73.1.1	INTEGER	read-only	The service being reported. This is the index into the table. Additional table rows for Frame Relay and ATM may be provided in the future.
INT nodeBilling	1.3.6.1.4.1.277.1.3.73.1.2	INTEGER	read-write	Switch to enable and disable billing on the STDX. When the value of nodeBilling is 'enabled', the value of a logical port's lportBilling object will take precedence. When the value of nodeBilling is 'disabled', it overrides all logical ports' lportBilling objects and billing is disabled across the entire switch. The default value of this object is 'disabled'.
TIK nodeBillingAggrPeriod	1.3.6.1.4.1.277.1.3.73.1.3	TimeTicks	read-write	Defines the length of the Billing Aggregation Period in seconds. The default value is 15 minutes. The minimum value is 10 minutes.
TIK nodeBillingCurAggrPeriodStart	1.3.6.1.4.1.277.1.3.73.1.4	TimeTicks	read-only	The start-time of the current aggregation period, given by the number of seconds since 00:00:00 UCT January 1, 1970.
TIK nodeBillingCurAggrPeriodEnd	1.3.6.1.4.1.277.1.3.73.1.5	TimeTicks	read-only	The end-time of the current aggregation period, given by the number of seconds since 00:00:00 UCT January 1, 1970.
TIK nodeBillingCollection	1.3.6.1.4.1.277.1.3.73.1.6	TimeTicks	read-write	Defines how often the Data Aggregation process on the CP is to poll the IOPs for usage data. The default value is 30 second. The range is unbounded, but practical use will dictate a range from 30 seconds to 1 minute.
INT nodeBillingDailyProcessing	1.3.6.1.4.1.277.1.3.73.1.7	INTEGER	read-write	Defines whether the Billing System is to perform a set of carrier-specific actions at the time given by nodeBillingDPTime. This object can be used to schedule the generation of statistics on a 24-hour basis, for example.
TIK nodeBillingDPTime	1.3.6.1.4.1.277.1.3.73.1.8	TimeTicks	read-write	Defines the time (given by the number of seconds since 00:00:00 UCT) that the Billing System is to perform a set of carrier-specific actions. This object can be used to schedule the generation of statistics on a 24-hour basis, for example.
CTR nodeBillingUsageRecOvflWarnings	1.3.6.1.4.1.277.1.3.73.1.9	Counter	read-only	Count of the number of usage record counter-value overflow conditions that have occurred during the current aggregation period. An overflow condition exists when an attempt was made to update a usage record counter, but such an update would have overflowed the counter. In this case, the usage record is closed and a new one is opened, if there is sufficient space in the service's aggregated usage data store.
CTR nodeBillingTotalUsageRecOvflWarnings	1.3.6.1.4.1.277.1.3.73.1.10	Counter	read-only	Count of the number of usage record overflow conditions that have occurred during the current day.
CTR nodeBillingBillableUsageEvents	1.3.6.1.4.1.277.1.3.73.1.11	Counter	read-only	Count of the number of data units (e.g, SMDS L3 PDUs) processed for billing treatment.
CTR nodeBillingNonBillableUsageEvents	1.3.6.1.4.1.277.1.3.73.1.12	Counter	read-only	Count of the number of data units (e.g, SMDS L3 PDUs) not considered for billing treatment.
CTR nodeBillingUsageRecCreated	1.3.6.1.4.1.277.1.3.73.1.13	Counter	read-only	Count of the number of usage records created during the current aggregation period.
CTR nodeBillingTotalUsageRecCreated	1.3.6.1.4.1.277.1.3.73.1.14	Counter	read-only	Count of the total number of usage records created during the current day.
CTR nodeBillingUsageRecCrFailures	1.3.6.1.4.1.277.1.3.73.1.15	Counter	read-only	Total number of usage records that could not be created during the current aggregation period. This counter is normally incremented when the usage data file is at capacity and no additional usage records can be added.
CTR nodeBillingTotalUsageRecCrFailures	1.3.6.1.4.1.277.1.3.73.1.16	Counter	read-only	Total number of usage records that could not be created during the current day.
CTR nodeBillingUsageRecSent	1.3.6.1.4.1.277.1.3.73.1.17	Counter	read-only	Total number of usage records that have been transferred to the Adjunct Billing Processor during the current aggregation period.
CTR nodeBillingTotalUsageRecSent	1.3.6.1.4.1.277.1.3.73.1.18	Counter	read-only	Total number of usage records that have been transferred to the Adjunct Billing Processor during the current day.
CTR nodeBillingUsageDataStoreFull	1.3.6.1.4.1.277.1.3.73.1.19	Counter	read-only	The number of times the aggregated usage data store became full during the current aggregation period.
CTR nodeBillingTotalUsageDataStoreFull	1.3.6.1.4.1.277.1.3.73.1.20	Counter	read-only	Total number of times the aggregated usage data store became full during the current day.
INT nodeBillingAdminAction	1.3.6.1.4.1.277.1.3.73.1.21	INTEGER	read-write	This object defines a set of administrative actions that can be performed by the Billing System. forceUpload - Forces the current aggregation period to end and the service's aggregated usage data file to be uploaded to the Adjunct Processor. A new aggregation period is then started. This action can be requested when billing is enabled or disabled for the service. This object always returns invalid(1) when read.
INT nodeRerouteAlg	1.3.6.1.4.1.277.1.3.74	INTEGER	read-write	The number of seconds delay between each reroute batch event.
INT nodeOamAlarmDisabled	1.3.6.1.4.1.277.1.3.76	INTEGER	read-write	If disabled then don't generate oam alarms for circuits that are down on this switch.
nodeRefclocksrcTable	1.3.6.1.4.1.277.1.3.77		not-accessible	A list of generators (sources) for the system reference clock on the node. This reference clock is used by the clock generation unit (CGU) to create the system clock. To this reference clock the constant bit rate ATM interface cards (CBR cards) are synchronized.
nodeRefclocksrcEntry	1.3.6.1.4.1.277.1.3.77.1		not-accessible	Information of a single system reference clock source.
INT nodeRefclocksrcIndex	1.3.6.1.4.1.277.1.3.77.1.1	INTEGER	read-write	A positive integer to identify an entry in the nodeRefclocksrcTable.
INT nodeRefclocksrcPriority	1.3.6.1.4.1.277.1.3.77.1.2	INTEGER	read-write	The priority of the system reference clock source. A source with a nodeRefclocksrcPriority=n means that this source is used before a source with a higher value of nodeRefclocksrcPriority as long as this source is available. The system choses one of the sources with the same lowest available value of nodeRefclocksrcPriority.
INT nodeRefclocksrcType	1.3.6.1.4.1.277.1.3.77.1.3	INTEGER	read-write	The type of the reference clock source. It is either an external clock source connected to a ATM-IWU or DS3 card, or the reference clock is recovered from the line interface.
INT nodeRefclocksrcSlotId	1.3.6.1.4.1.277.1.3.77.1.4	INTEGER	read-write	The card number of the reference clock source. In case of an external clock interface this is the number of the card as defined in cardLogicalSlotId. In case of a clock recovered from the line interface it is the number of the corresponding card as defined in cardLogicalSlotId.
INT nodeRefclocksrcPportId	1.3.6.1.4.1.277.1.3.77.1.5	INTEGER	read-write	The interface number of the reference clock source. In case of an external clock interface this is meaningless. In case of a clock recovered from the line interface it is the number of the corresponding pport as defined in pportId.
INT nodeRefclockActiveSrc	1.3.6.1.4.1.277.1.3.78	INTEGER	read-only	The entry number of the active reference clock source in nodeRefclocksrcTable. If zero, the CGU is in free-running mode or holdover mode using the last PLL parameters.
INT nodeRefclockActiveCGUSlotId	1.3.6.1.4.1.277.1.3.79	INTEGER	read-only	The physical slot id of the current master CGU board.
INT nodeRefclockActiveCGUMode	1.3.6.1.4.1.277.1.3.80	INTEGER	read-only	The clock mode of the current master CGU board.
INT nodeInitiateImageBackup	1.3.6.1.4.1.277.1.3.81	INTEGER	read-write	When set, copy all of the runtime application images and configuration images to there corresponding backup locations on the hard disk.
INT nodeImageBackupState	1.3.6.1.4.1.277.1.3.82	INTEGER	read-only	Provides the current state of the images backup operation.
INT nodeInitiateImageRestore	1.3.6.1.4.1.277.1.3.83	INTEGER	read-write	When set, copy all of the runtime application images and configuration images from their BACKUP locations on the hard disk to there corresponding ACTIVE locations on the hard disk. Once completed, reboot the entire node.
nodeApplicationTable	1.3.6.1.4.1.277.1.3.84		not-accessible	A list of Application Image Descriptions.
nodeApplicationEntry	1.3.6.1.4.1.277.1.3.84.1		not-accessible	An Application Entry contains a description of the application image, the version of the PRIMARY copy and the version of the SECONDARY copy.
IND nodeApplicationIndex	1.3.6.1.4.1.277.1.3.84.1.1	Index	read-only	The numeric index of application images. 1 - SP Runtime Application 2 - IOM Type A Runtime Application 3 - IOM Type B Runtime Application 4 - IOM Type C Runtime Application 5 - IOM Type D Runtime Application
STR nodeApplicationDescription	1.3.6.1.4.1.277.1.3.84.1.2	DisplayString	read-only	The description of this Application Image.
STR nodePrimaryVersion	1.3.6.1.4.1.277.1.3.84.1.3	DisplayString	read-only	The version of the PRIMARY Application Image.
STR nodeSecondaryVersion	1.3.6.1.4.1.277.1.3.84.1.4	DisplayString	read-only	The version of the SECONDARY Application Image.
INT nodePrimarySyncRefAdminState	1.3.6.1.4.1.277.1.3.85	INTEGER	read-write	The requested primary clock synchronization reference source.
INT nodePrimarySyncRefOperationalState	1.3.6.1.4.1.277.1.3.86	INTEGER	read-only	The actual primary clock synchronization reference source.
INT nodeSecondarySyncRefAdminState	1.3.6.1.4.1.277.1.3.87	INTEGER	read-write	The requested secondary clock synchronization reference source.
INT nodeSecondarySyncRefOperationalState	1.3.6.1.4.1.277.1.3.88	INTEGER	read-only	The actual secondary clock synchronization reference source.
INT nodePrimaryPLLOperationalState	1.3.6.1.4.1.277.1.3.89	INTEGER	read-only	The current state of the primary synchronization PLL.
INT nodeSecondaryPLLOperationalState	1.3.6.1.4.1.277.1.3.90	INTEGER	read-only	The current state of the secondary synchronization PLL.
INT nodeExternalClockAOperationalState	1.3.6.1.4.1.277.1.3.91	INTEGER	read-only	The current state of the External Clock A reference.
INT nodeExternalClockBOperationalState	1.3.6.1.4.1.277.1.3.92	INTEGER	read-only	The current state of the External Clock B reference.
INT nodePortClockAOperationalState	1.3.6.1.4.1.277.1.3.93	INTEGER	read-only	The current state of the Port Clock A reference.
INT nodePortClockBOperationalState	1.3.6.1.4.1.277.1.3.94	INTEGER	read-only	The current state of the Port Clock B reference.
INT nodeExternalTimingSource	1.3.6.1.4.1.277.1.3.95	INTEGER	read-write	The reference for the external timing output.
INT nodeSyncAutoRestore	1.3.6.1.4.1.277.1.3.96	INTEGER	read-write	The configuration of the Synchronization Reference Auto Restoration function.
INT nodeExternalClockInterfaceType	1.3.6.1.4.1.277.1.3.97	INTEGER	read-only	The interface type of the External Clock references.
pport	1.3.6.1.4.1.277.1.4
INT pportNumber	1.3.6.1.4.1.277.1.4.1	INTEGER	read-only	The number of physical ports (regardless of their current state) present at this node.
pportTable	1.3.6.1.4.1.277.1.4.2		not-accessible	A list of physical port entries. The number of entries is given by the value of pportNumber.
pportEntry	1.3.6.1.4.1.277.1.4.2.1		not-accessible	The physical port entry contains objects relevant to a physical port.
INT pportSlotId	1.3.6.1.4.1.277.1.4.2.1.1	INTEGER	read-only	The slot number of the corresponding physical port.
INT pportId	1.3.6.1.4.1.277.1.4.2.1.2	INTEGER	read-only	The port number of the corresponding physical port on the board.
INT pportAdminType	1.3.6.1.4.1.277.1.4.2.1.3	INTEGER	read-write	The defined type of the board which the physical port is on.
INT pportNumLport	1.3.6.1.4.1.277.1.4.2.1.4	INTEGER	read-only	The number of logical ports on the physical port.
INT pportDataRate	1.3.6.1.4.1.277.1.4.2.1.5	INTEGER	read-write	An estimate of the physical port's data rate in bits per second. The data rate can't be an arbitrary value. The legal values are list below. Note that the T1/E1 class of cards don't support this variable and return a 0 For UIO, DSX1: 9600, 19200, 38400, 48000, 56000, 64000, 128000, 192000, 256000, 320000, 384000, 448000, 512000, 576000, 640000, 704000, 768000, 832000, 896000, 960000, 1024000, 1088000, 1152000, 1216000, 1280000, 1344000, 1408000, 1472000, 1536000, 1600000, 1664000, 1728000, 1792000, 1856000, 1920000, 1984000, 2048000, 4096000, 6144000, 8192000 For HSSI: 1579000, 3158000, 4737000, 6316000, 7895000, 9474000, 11053000, 12632000, 14211000, 15790000, 17369000, 18948000, 20527000, 22106000, 23685000, 25264000, 26843000, 28422000, 30001000, 31580000, 33159000, 34738000, 36317000, 37896000, 39475000, 41054000, 42633000, 44212000, 45791000, 47370000, 48949000, 50528000 For ATM-IWU, TOPAZ OC3c: 155520000 For T1, E1, UT1, UE1, PRI, SH-T1: 0
INT pportType	1.3.6.1.4.1.277.1.4.2.1.6	INTEGER	read-only	The actual type of the physical port.
INT pportRecvClock	1.3.6.1.4.1.277.1.4.2.1.7	INTEGER	read-only	The receive clock source. This object works in cooperation with pportXmitClock. The following are the various values for different clock source types: Type Clock Source pportRevClock pportXmitClock { pportEntry 7 } { pportEntry 8 } V.35 DCE ............ 0 0 or UIO LoopTime DCE ... 3 0 DTE ............ 1 2 Direct Trunk ... 1 0 T1 or Loop Timed ..... 1 1 E1 Internal ....... 2 2 External ....... don't care 3
INT pportXmitClock	1.3.6.1.4.1.277.1.4.2.1.8	INTEGER	read-only	The transmit clock source. This object works in cooperation with pportXmitClock. The following are the various values for different clock source types: Type Clock Source pportRevClock pportXmitClock { pportEntry 7 } { pportEntry 8 } V.35 DCE ............ 0 0 or UIO LoopTime DCE ... 3 0 DTE ............ 1 2 Direct Trunk ... 1 0 T1 or Loop Timed ..... 1 1 E1 Internal ....... 2 2 External ....... don't care 3
INT pportAdminStatus	1.3.6.1.4.1.277.1.4.2.1.9	INTEGER	read-write	The desired state of the physical port.
INT pportOperStatus	1.3.6.1.4.1.277.1.4.2.1.10	INTEGER	read-only	The current state of the physical port.
INT pportDs1LineType	1.3.6.1.4.1.277.1.4.2.1.11	INTEGER	read-write	The line type of the T1 or FT1-24B port. ANSI ESF is equivalent to Bellcore ESF.
INT pportDs1ZeroCoding	1.3.6.1.4.1.277.1.4.2.1.12	INTEGER	read-write	The variety of zero code suppression used on the T1 or FT1-24B link. Jammed bit is equivalent to dsx1JBZS where the DS0s will run at 56K bps.
INT pportDs1LineBuildout	1.3.6.1.4.1.277.1.4.2.1.13	INTEGER	read-write	The line build out or line length specification for the DS1 or DSX-1 transmitter. These values are card specific: 10 port DSX-1 card ------------------ The accepted values are: 1 - 0 to 110 feet 2 - 110 to 220 feet 3 - 220 to 330 feet 4 - 330 to 440 feet 5 - 440 to 550 feet 6 - 550 to 660 feet 7 - over 655 feet 1-port and 4-port T1 cards -------------------------- The accepted values are: 96 - 0 to 133 feet 128 - 133 to 266 feet 160 - 266 to 399 feet 192 - 399 to 533 feet 224 - 533 to 655 feet 96 - 0 db 32 - -7.5 db 64 - -15 db 4-port CBR card --------------- The accepted values are: 96 - 0 db 32 - -7.5 db 64 - -15 db 4-port Short Haul T1 cards -------------------------- The accepted values are: 96 - 0 to 133 feet 128 - 133 to 266 feet 160 - 266 to 399 feet 192 - 399 to 533 feet 224 - 533 to 655 feet
INT pportDiagTestId	1.3.6.1.4.1.277.1.4.2.1.14	INTEGER	read-write	Identification for the diagnostics tests to be run.
INT pportDiagTestRuns	1.3.6.1.4.1.277.1.4.2.1.15	INTEGER	read-write	The number of passes of the diagnostics tests to be run. The default value is 1.
CTR pportInOctets	1.3.6.1.4.1.277.1.4.2.1.16	Counter	read-only	The total number of octets received on the physical port, including framing characters.
CTR pportInFrames	1.3.6.1.4.1.277.1.4.2.1.17	Counter	read-only	The total number of frames received on the physical port.
CTR pportInDiscards	1.3.6.1.4.1.277.1.4.2.1.18	Counter	read-only	The total number of inbound frames discarded.
CTR pportInErrors	1.3.6.1.4.1.277.1.4.2.1.19	Counter	read-only	The total number of inbound frames that contained erroneous headers (e.g., illegal or unknown DLCIs).
CTR pportOutOctets	1.3.6.1.4.1.277.1.4.2.1.20	Counter	read-only	The total number of octets transmitted out of the physical port, including framing characters.
CTR pportOutFrames	1.3.6.1.4.1.277.1.4.2.1.21	Counter	read-only	The total number of frames transmitted out of the physical port.
CTR pportOutDiscards	1.3.6.1.4.1.277.1.4.2.1.22	Counter	read-only	The total number of outbound frames discarded due to severe congestion.
CTR pportOutErrors	1.3.6.1.4.1.277.1.4.2.1.23	Counter	read-only	The total number of outbound frames that causes xmit errors.
INT pportDiagState	1.3.6.1.4.1.277.1.4.2.1.24	INTEGER	read-write	The current state of the diagnostic on this physical port.
OCT pportDiagOptionStr	1.3.6.1.4.1.277.1.4.2.1.25	OCTET STRING	read-write	Optional parameters to the diagnostic.
INT pportDiagPassCount	1.3.6.1.4.1.277.1.4.2.1.26	INTEGER	read-only	Number of successful diagnostic passes.
INT pportDiagFailCount	1.3.6.1.4.1.277.1.4.2.1.27	INTEGER	read-only	Number of failed diagnostic passes.
STR pportDiagResultStr	1.3.6.1.4.1.277.1.4.2.1.28	DisplayString	read-only	Description of last diagnostic failure.
INT pportLinkDownReason	1.3.6.1.4.1.277.1.4.2.1.29	INTEGER	read-only	Reason why the link is down. The blue-alarm is equivalent to the Alarm Indication Signal (AIS) failure.
INT pportInterface	1.3.6.1.4.1.277.1.4.2.1.30	INTEGER	read-only	Actual interface connected to Multi-Interface Port or ATM-IWU.
INT pportAdminInterface	1.3.6.1.4.1.277.1.4.2.1.31	INTEGER	read-write	Configured interface connected to Multi-Interface Port or ATM-IWU.
INT pportCellScramble	1.3.6.1.4.1.277.1.4.2.1.32	INTEGER	read-write	Configured ATM cell payload scrambling.
INT pportCbitParity	1.3.6.1.4.1.277.1.4.2.1.33	INTEGER	read-write	Configured ATM DS3 C-bit Parity.
INT pportMaxBufferSize	1.3.6.1.4.1.277.1.4.2.1.34	INTEGER	read-write	Maximum receive/transmit buffer size for the ATM UNI DS3 IOP
INT pportPeakCellRate0	1.3.6.1.4.1.277.1.4.2.1.35	INTEGER	read-write	Peak Cell Rate (cell/sec.) for rate queue #0. rate queues 0 - 3 are high priority
INT pportPeakCellRate1	1.3.6.1.4.1.277.1.4.2.1.36	INTEGER	read-write	Peak Cell Rate (cell/sec.) for rate queue #1. rate queues 0 - 3 are high priority
INT pportPeakCellRate2	1.3.6.1.4.1.277.1.4.2.1.37	INTEGER	read-write	Peak Cell Rate (cell/sec.) for rate queue #2. rate queues 0 - 3 are high priority
INT pportPeakCellRate3	1.3.6.1.4.1.277.1.4.2.1.38	INTEGER	read-write	Peak Cell Rate (cell/sec.) for rate queue #3. rate queues 0 - 3 are high priority
INT pportPeakCellRate4	1.3.6.1.4.1.277.1.4.2.1.39	INTEGER	read-write	Peak Cell Rate (cell/sec.) for rate queue #4. rate queues 4 - 7 are low priority
INT pportPeakCellRate5	1.3.6.1.4.1.277.1.4.2.1.40	INTEGER	read-write	Peak Cell Rate (cell/sec.) for rate queue #5. rate queues 4 - 7 are low priority
INT pportPeakCellRate6	1.3.6.1.4.1.277.1.4.2.1.41	INTEGER	read-write	Peak Cell Rate (cell/sec.) for rate queue #6. rate queues 4 - 7 are low priority
INT pportPeakCellRate7	1.3.6.1.4.1.277.1.4.2.1.42	INTEGER	read-write	Peak Cell Rate (cell/sec.) for rate queue #7. rate queues 4 - 7 are low priority
INT pportInCells	1.3.6.1.4.1.277.1.4.2.1.43	INTEGER	read-only	The total number of cells received
INT pportInErrorCells	1.3.6.1.4.1.277.1.4.2.1.44	INTEGER	read-only	The total number of cells received with error
INT pportOutCells	1.3.6.1.4.1.277.1.4.2.1.45	INTEGER	read-only	The total number of cells transmitted
INT pportDs3LineBuildout	1.3.6.1.4.1.277.1.4.2.1.46	INTEGER	read-write	The line build out or line length specification for the DS3 transmitter. 1-port ATM-UNI DS3 card -------------------------- The accepted values are: 1 - 0 to 225 feet 2 - 226 to 450 feet
INT pportSetDS0LoopUp	1.3.6.1.4.1.277.1.4.2.1.47	INTEGER	read-write	Bit map used to set one or more DS0's into loopback. Low bit corresponds to DS0 1. If a bit is set that DS0 is put into loopback.
INT pportSetDS0LoopDown	1.3.6.1.4.1.277.1.4.2.1.48	INTEGER	read-write	Bit map used to set one or more DS0's out of loopback. Low bit corresponds to DS0 1. If a bit is set that DS0 is put out of loopback.
INT pportDS0LoopUpStatus	1.3.6.1.4.1.277.1.4.2.1.49	INTEGER	read-only	Bit map reporting which DS0's have gone into loopback since the last time this variable was read
INT pportDS0LoopDownStatus	1.3.6.1.4.1.277.1.4.2.1.50	INTEGER	read-only	Bit map reporting which DS0's have gone out of loopback since the last time this variable was read
INT pportDS0LoopStatus	1.3.6.1.4.1.277.1.4.2.1.51	INTEGER	read-only	Bit map reporting which DS0's are currently in loopback. Low bit corresponds to DS0 1
INT pportISDN	1.3.6.1.4.1.277.1.4.2.1.52	INTEGER	read-write	Specifies whether ISDN PRI is enabled for this physical port
INT pportdsx3LoopbackConfig	1.3.6.1.4.1.277.1.4.2.1.53	INTEGER	read-write	Integer used to set the loopback state of the DS3 or E3
INT pportdsx3SendCode	1.3.6.1.4.1.277.1.4.2.1.54	INTEGER	read-write	Integer used to send loopback code to far-end DS3
INT pportdsx3LoopStatus	1.3.6.1.4.1.277.1.4.2.1.55	INTEGER	read-only	Integer indicating the current loopback status of the DS3 or E3
INT pportdsx3FEACStatus	1.3.6.1.4.1.277.1.4.2.1.56	INTEGER	read-only	Integer indicating the current DS3 FAEC status: -- none (0), DS3 Equipment Failure (1), DS3 LOS (2), DS3 Out of Frame (4), DS3 AIS received (8), DS3 IDLE received (16), DS3 Equipment-Failure (NSA) (32), DS3 Common Equipment Failure (64), DS3 Loopback received (128)
INT pportds1LoopbackConfig	1.3.6.1.4.1.277.1.4.2.1.57	INTEGER	read-write	Integer used to set the loopback state of the DS1
INT pportds1SendCode	1.3.6.1.4.1.277.1.4.2.1.58	INTEGER	read-write	Integer used to send loopback code to far-end DS1
INT pportds1LoopStatus	1.3.6.1.4.1.277.1.4.2.1.59	INTEGER	read-only	Integer indicating the current loopback status of the DS1
INT pportSetClkBkup	1.3.6.1.4.1.277.1.4.2.1.60	INTEGER	read-only	The desired clock source backup if the card is set in external clock source mode
INT pportAtmIdleWord	1.3.6.1.4.1.277.1.4.2.1.61	INTEGER	read-write	The word used to stuff the payload of the ATM idle cell
INT pportAtmDisCardMode	1.3.6.1.4.1.277.1.4.2.1.62	INTEGER	read-write	The desired clock source backup if the card is set in external clock source mode
INT pportAtmLastUnconfiguredVpi	1.3.6.1.4.1.277.1.4.2.1.63	INTEGER	read-only	This entry holds the Vpi read from the last Unconfigured atm cell received. This entry applies to ATM pports only.
INT pportAtmLastUnconfiguredVci	1.3.6.1.4.1.277.1.4.2.1.64	INTEGER	read-only	This entry holds the Vci read from the last Unconfigured atm cell received. This entry applies to ATM pports only.
CTR pportAtmUnconfiguredCells	1.3.6.1.4.1.277.1.4.2.1.65	Counter	read-only	This entry holds a count of the number of Unconfigured ATM cells received. This entry applies to ATM pports only.
INT pportAtmNumBitsVCI	1.3.6.1.4.1.277.1.4.2.1.66	INTEGER	read-only	This entry holds a count of the VCI bits supppoted my this ATM card.
INT pportAtmNumBitsVPI	1.3.6.1.4.1.277.1.4.2.1.67	INTEGER	read-only	This entry holds a count of the VPI bits supppoted my this ATM card.
INT pportAtmInterfaceType	1.3.6.1.4.1.277.1.4.2.1.68	INTEGER	read-write	Integer used to set ATM UNI or NNI type
INT pportSonetSDHLoopbackConfig	1.3.6.1.4.1.277.1.4.2.1.69	INTEGER	read-write	Integer used to set the loopback state of the Sonet/SDH port
INT pportSonetSDHLoopStatus	1.3.6.1.4.1.277.1.4.2.1.70	INTEGER	read-only	Integer indicating the current loopback status of the Sonet/SDH port
CTR pportOutDiscardsCell	1.3.6.1.4.1.277.1.4.2.1.71	Counter	read-only	The total number of outbound cell discarded due to congestion.
INT pportAtmPlcp	1.3.6.1.4.1.277.1.4.2.1.72	INTEGER	read-write	The PLCP maintains the state of the ATM Physical Layer Convergence Protocol. When the protocol is disabled atm direct mapping is used with hec cell delineation.
INT pportCbrTargetClockMode	1.3.6.1.4.1.277.1.4.2.1.73	INTEGER	read-write	The clocking method to be used by the CBR card. 4-port CBR card ----------------------------------------------- 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adaptive clock method
INT pportCbrCurrentClockMode	1.3.6.1.4.1.277.1.4.2.1.74	INTEGER	read-only	The clocking method currently used by the CBR card. 4-port CBR card ----------------------------------------------- 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adaptive clock method
INT pportClockMasterChannel	1.3.6.1.4.1.277.1.4.2.1.75	INTEGER	read-write	The number of the channel (lport) on this pport that is used as ACM/SRTS master for this line interface: 4-port CBR E1/DS1 card (structured mode): 1..4
INT pportFibreType	1.3.6.1.4.1.277.1.4.2.1.76	INTEGER	read-only	The type of fibre connected to the ATM-IWU. Its type determines the maximum transmission distance. 1-port ATM-IWU STM-1/STS-3c card -------------------------------- 4 - multimode fibre (maximum transmission distance approx. 2 km) 2 - single mode fibre short haul (maximum transmission distance approx. 20 km)
INT pportLaserStatus	1.3.6.1.4.1.277.1.4.2.1.77	INTEGER	read-write	The configured state of the laser: 1-port ATM-IWU STM-1/STS-3c card & Topaz 4-port OC3 & STM-1 card ---------------------------------------------------------------- 1 - off 2 - on
INT pportMaxActiveVpiBits	1.3.6.1.4.1.277.1.4.2.1.78	INTEGER	read-write	The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI bits configured for use ranges from 0 to 8 only.
INT pportBipErrorsThresh	1.3.6.1.4.1.277.1.4.2.1.79	INTEGER	read-write	The threshold of BIP errors. If the number of line BIP-24/8 rrors persists to exceed this value, the pport will be taken down and a trap will be issued: 1-port ATM-IWU STM-1/STS-3c card: -------------------------------- 1 - ignore BIP errors 4 - 10^-4 errors 5 - 10^-5 errors 6 - 10^-6 errors
CTR pportBipSectionErrors	1.3.6.1.4.1.277.1.4.2.1.80	Counter	read-only	The number of B1 section BIP-8 errors since the last reset.
CTR pportBipLineErrors	1.3.6.1.4.1.277.1.4.2.1.81	Counter	read-only	The number of line BIP-24/8 errors since the last reset.
CTR pportBipPathErrors	1.3.6.1.4.1.277.1.4.2.1.82	Counter	read-only	The number of B3 path BIP-8 errors since the last reset.
CTR pportFebeErrors	1.3.6.1.4.1.277.1.4.2.1.83	Counter	read-only	The number of line Far End Block Errors since the last reset.
CTR pportHcsErrors	1.3.6.1.4.1.277.1.4.2.1.84	Counter	read-only	The number of correctable HCS errors since the last reset.
CTR pportHcsSevereErrors	1.3.6.1.4.1.277.1.4.2.1.85	Counter	read-only	The number of uncorrectable HCS errors since the last reset.
CTR pportCongestedReceivedCells	1.3.6.1.4.1.277.1.4.2.1.86	Counter	read-only	The number of received cells that were discarded due to congestion of the ATM-IWU, since the last reset.
CTR pportCongestedTransmittedCells	1.3.6.1.4.1.277.1.4.2.1.87	Counter	read-only	The number of cells to be transmitted, that were discarded due to congestion of the ATM-IWU, since the last reset.
CTR pportAtmLayerErroredReceivedCells	1.3.6.1.4.1.277.1.4.2.1.88	Counter	read-only	The number of received cells that were discarded due to ATM layer errors, since the last reset.
CTR pportAtmLayerErroredTransmittedCells	1.3.6.1.4.1.277.1.4.2.1.89	Counter	read-only	The number of cells to be transmitted, that were discarded due to ATM layer errors, since the last reset.
INT pportDS0BitStuff	1.3.6.1.4.1.277.1.4.2.1.90	INTEGER	read-write	Bit stuffing on or off for 2047 bit pattern in DS0 far end testing.
INT pportDS0BitErrorCount	1.3.6.1.4.1.277.1.4.2.1.91	INTEGER	read-only	Total number of errors in 2047 DS0 far end testing.
INT pportDS0BitErrorFreeSeconds	1.3.6.1.4.1.277.1.4.2.1.92	INTEGER	read-only	Total number of error free seconds in 2047 DS0 far end testing.
INT pportDS0BitErroredSeconds	1.3.6.1.4.1.277.1.4.2.1.93	INTEGER	read-only	Total number of errored seconds in 2047 DS0 far end testing.
INT pportDS0MidspanRepeaters	1.3.6.1.4.1.277.1.4.2.1.94	INTEGER	read-write	Number of Midspan repeaters in a link to be punched thru for DS0 far end testing.
INT pportDS0TestPatternSync	1.3.6.1.4.1.277.1.4.2.1.95	INTEGER	read-only	While DS0 far end testing, the DS0 pattern has detected the pattern four consecutive times. If the pattern is lost, this variable will be equal to one.
INT pportDS0InjectBitError	1.3.6.1.4.1.277.1.4.2.1.96	INTEGER	read-write	While testing DS0 far end lpbk, setting this variable will inject a bit error into the test pattern.
INT pportDS0FarendLpbkType	1.3.6.1.4.1.277.1.4.2.1.97	INTEGER	read-write	The type of DS0 equipment to be looped back at the far end during DS0 far end testing. 1 - OCU 2 - DSU 3 - CSU.
INT pportDS0LpbkMode	1.3.6.1.4.1.277.1.4.2.1.98	INTEGER	read-write	This determines what mode the DS0 Processor will be set to. 1 - no lpbk 2 - switch lpbk 3 - far end lpbk.
INT pportDS0SwitchLpbkStart	1.3.6.1.4.1.277.1.4.2.1.99	INTEGER	read-write	This is the first DS0 in a sting of consecutive DS0's to be looped back at the switch if the DS0 processor is set to switch loopback. If it's set to far end loopback, this determines which singleton DS0 will be monitored at the receive end.
INT pportDS0SwitchLpbkEnd	1.3.6.1.4.1.277.1.4.2.1.100	INTEGER	read-write	This is the Last DS0, +1, in a sting of consecutive DS0's to be looped back at the switch if the DS0 processor is set to switch loopback. If the DS0 processor is set to far end loopback, this value will equal pportDS0SwitchLpbkStart + 1..
INT pportDS0FarendDS0InLpbk	1.3.6.1.4.1.277.1.4.2.1.101	INTEGER	read-only	This indicates the DS0 in far end loopback.
INT pportDS0SendTestTraffic	1.3.6.1.4.1.277.1.4.2.1.102	INTEGER	read-write	Enable or Disable sending DS0 2047 test pattern for DS0 far end testing.
INT pportOc3LoopConfig	1.3.6.1.4.1.277.1.4.2.1.103	INTEGER	read-write	The loopback state of the ATM IWU OC3
INT pportOc3LoopStatus	1.3.6.1.4.1.277.1.4.2.1.104	INTEGER	read-only	The current loopback status of the ATM IWU OC3
IP pportISDNIpBaseAddr	1.3.6.1.4.1.277.1.4.2.1.105	IpAddress	read-write	Specifies the base address used for IP Dynamic Address Assignment
INT pportSonetSTM1Scramble	1.3.6.1.4.1.277.1.4.2.1.106	INTEGER	read-write	Configured SONET/STM-1 scrambling.
INT pportEFCIMarking	1.3.6.1.4.1.277.1.4.2.1.107	INTEGER	read-write	Configured EFCI marking for cell traffic in Topaz IOMs
INT pportAtmQOSTransmitMode	1.3.6.1.4.1.277.1.4.2.1.108	INTEGER	read-write	Select fix priority or weighted round-robin for cell transmission in different ATM QOS classes.
INT pportHECMode	1.3.6.1.4.1.277.1.4.2.1.109	INTEGER	read-write	Configured ATM HEC single bit error correction routine.
OCT pportISDNChannelStatus	1.3.6.1.4.1.277.1.4.2.1.110	OCTET STRING	read-only	The ISDN call status of all the B-Channels on the pport are encoded into this 24 character, (for T1 ISDN PRI card...23B+D) or 31 character, (for E1 ISDN PRI card...30B+D ) ASCII string. The respective call state for each B-Channel is represented in its corresponding bit position. The D-Channel status is similarly encoded into the appropriate bit position (24th for T1) or (16th for E1). The encoding legend is as follows... I B-Channel is in Idle state R B-Channel is in Dialing (Ringing) state C B-Channel is in Connected (Active) state H B-Channel is in Releasing (Hanging-up) state U D-Channel is Up D D-Channel is Down
INT pportds1FarEndLoopStatus	1.3.6.1.4.1.277.1.4.2.1.111	INTEGER	read-write	DS1 Far End Loopback Status as commanded by the switch
INT pportds1FDLControl	1.3.6.1.4.1.277.1.4.2.1.112	INTEGER	read-write	Enables or Disables FDL Function for DS1 ESF pport
INT pportds1FDLPrmXmit	1.3.6.1.4.1.277.1.4.2.1.113	INTEGER	read-write	Enables or Disables transmission of Performance Monitoring Report (PRM) messages on the DS1 ESF FDL
INT pportds1FDLPidXmit	1.3.6.1.4.1.277.1.4.2.1.114	INTEGER	read-write	Enables or Disables transmission of Path ID (PID) messages on the DS1 ESF FDL
OCT pportds1FDLXmitPid	1.3.6.1.4.1.277.1.4.2.1.115	OCTET STRING	read-write	Transmit Path Id to be sent on the DS1 ESF FDL. (76 bytes)
OCT pportds1FDLRcvPid	1.3.6.1.4.1.277.1.4.2.1.116	OCTET STRING	read-only	The last path id message received on the DS1 ESF FDL. (76 bytes)
OCT pportds1FDLRcvTsid	1.3.6.1.4.1.277.1.4.2.1.117	OCTET STRING	read-write	The last test id message received on the DS1 ESF FDL. (76 bytes)
INT pportSonetSDHFramingMode	1.3.6.1.4.1.277.1.4.2.1.118	INTEGER	read-write	The Framing mode for SONET/SDH port interface types.
INT pportds1InbandLoopType	1.3.6.1.4.1.277.1.4.2.1.119	INTEGER	read-write	Integer used to distinguish Inband Line loopback code sent from the switch when commanding inband line loopbacks, and reckognized by the switch when responding to remote loopback commands
INT pportESFDataLinkStatus	1.3.6.1.4.1.277.1.4.2.1.120	INTEGER	read-only	The current status of the DS1 ESF (FDL) data link.
INT pportPMTcaId	1.3.6.1.4.1.277.1.4.2.1.121	INTEGER	read-write	This object identifies the the most recently declared pport threshold crossing alert
INT pportBchanTimerValue	1.3.6.1.4.1.277.1.4.2.1.122	INTEGER	read-write	This value is used on a per port basis to add a delay to answering a ISDN call of the initial Disconnect from the network. This due to the ARP cache not updating quick enough on the routers
CTR pportAAL5CRC32Error	1.3.6.1.4.1.277.1.4.2.1.123	Counter	read-only	Number of received AAL5 packets with CRC32 errors.
CTR pportAAL5CPIError	1.3.6.1.4.1.277.1.4.2.1.124	Counter	read-only	Number of received AAL5 packets with CPI errors The only valid value currently defined for the CPI field is all zeros
CTR pportAAL5LengthError	1.3.6.1.4.1.277.1.4.2.1.125	Counter	read-only	Number of received AAL5 packets which satisfied one of the following error conditions: 1. number of received cells * 48 bytes - length value in trailer > 55 bytes 2. number of received cells * 48 bytes - length value in trailer < 8 bytes
CTR pportAAL5ReassemblyTimerError	1.3.6.1.4.1.277.1.4.2.1.126	Counter	read-only	Number of expired reassembly timers
CTR pportAAL5MaxNrSegError	1.3.6.1.4.1.277.1.4.2.1.127	Counter	read-only	Number of received AAL5 packets which exceeds the maximum allowed length
INT pportRedundancyArch	1.3.6.1.4.1.277.1.4.2.1.128	INTEGER	read-write	Pport redundancy architecture. Default is disabled. aps-intracard -- ports are both on same card. aps-with-resilient-uni -- ports may be on different cards, resilient UNI is used to reroute traffic. aps-intercard-trunk-backup -- ports may be on different cards, aps keeps phy layer in sync w/trunk backup.
INT pportAPSadminDir	1.3.6.1.4.1.277.1.4.2.1.129	INTEGER	read-write	Provisioned APS switch-direction-mode. Default is uni- directional.
INT pportAPSlineType	1.3.6.1.4.1.277.1.4.2.1.130	INTEGER	read-write	APS line type for the pport. Writable only when pportRedundancyArch is disabled.
INT pportAPSrevertiveMode	1.3.6.1.4.1.277.1.4.2.1.131	INTEGER	read-write	APS revertive mode. When revertive, after the condition for an automatic switchover clears, user traffic will be switched back to the working line after the pportAPSwtrPeriod expires. Default is revertive.
INT pportAPSpairedSlotId	1.3.6.1.4.1.277.1.4.2.1.132	INTEGER	read-write	Slot ID of the paired-with APS pport. Writable only when pportRedundancyArch is disabled.
INT pportAPSpairedPportId	1.3.6.1.4.1.277.1.4.2.1.133	INTEGER	read-write	Pport ID of the paired-with APS pport. Writable only when pportRedundancyARch is disabled.
INT pportAPSsfBerThresh	1.3.6.1.4.1.277.1.4.2.1.134	INTEGER	read-write	Exponent N for APS Signal Failure based on BER. A line bit-error-rate above 10^-N causes an SF BER failure to be asserted. SF BER is cleared when the line BER returns to less than 10^-7.
INT pportAPSsdBerThresh	1.3.6.1.4.1.277.1.4.2.1.135	INTEGER	read-write	Exponent N for APS Signal Degrade based on BER. A line bit-error-rate above 10^-N causes an SD BER failure to be asserted. SD BER is cleared when the line BER returns to less than 10^-(N+1).
INT pportAPSwtrPeriod	1.3.6.1.4.1.277.1.4.2.1.136	INTEGER	read-write	APS wait-to-restore period. The number of minutes to wait after an automatic switch condition clears before switching back to the working line.
INT pportAPSprotectionLineState	1.3.6.1.4.1.277.1.4.2.1.137	INTEGER	read-only	Indicates the state of the protection line selector. When selected, a protection switchover has taken place and user traffic is being selected from the protection line.
INT pportAPSxCommand	1.3.6.1.4.1.277.1.4.2.1.138	INTEGER	read-write	External switch commands. The clear command clears any previously activated external command. Manual switch is preemptable by auto-switch-requests (line failures) while forced switch is not preemptable (except if the protection line fails). Manual and forced switch from protection to working, is valid only for 1+1 mode. Exercise simulates a switchover using APS signalling without actually performing a switch to protection line.
INT pportAPSconfigStatus	1.3.6.1.4.1.277.1.4.2.1.139	INTEGER	read-only	Status of APS pport configuration. The not-configured status indicates the pport APS feature is not configured or it is a non-APS pport. The valid state indicates the pport APS function is configured and has been validated by the APS manager. The invalid state indicates that the APS manager has detected a conflict between the working line and protection line pport configurations. The user must clear the invalid state by changing the configuration of the misconfigured pport as soon as possible. Check pportAPSadminDir, pportAPSlineType, pportAPSrevertiveMode, and pportAPSwtrPeriod for any misconfigurations.
INT pportAPSOperRxStatus	1.3.6.1.4.1.277.1.4.2.1.140	INTEGER	read-only	The current state of the pair of APS pports with respect to the ability of the pair to Receive user traffic. When indicated as up, user traffic may be received on at least one of the ports in the APS pair.
INT pportBertPattern	1.3.6.1.4.1.277.1.4.2.1.141	INTEGER	read-write	Pattern generated by the XBERT
INT pportBertUserBytes	1.3.6.1.4.1.277.1.4.2.1.142	INTEGER	read-write	Definition of 1,2,3 or 4 byte pattern if UserNByte selected.
INT pportBertErrorRate	1.3.6.1.4.1.277.1.4.2.1.143	INTEGER	read-write	Error rate to insert in generated pattern.
INT pportBertCommand	1.3.6.1.4.1.277.1.4.2.1.144	INTEGER	read-write	Single shot commands to the BERT.
INT pportBertStatus	1.3.6.1.4.1.277.1.4.2.1.145	INTEGER	read-only	Current status of the BERT for this channel.
GAU pportBertBitCount	1.3.6.1.4.1.277.1.4.2.1.146	Gauge	read-only	The number of bits received - stops counting at 0xFFFFFFFF
GAU pportBertErrorCount	1.3.6.1.4.1.277.1.4.2.1.147	Gauge	read-only	The number of bits received in error- stops counting at 0xFFFFFFFF
INT pportds1FELoopbackControl	1.3.6.1.4.1.277.1.4.2.1.148	INTEGER	read-write	Enables or Disables Far end loopback control of the switch. Enabled (2) = Loop up and down commands from far end equipment will be processed. Disabled (1) - loop up and down commands from far end equipment shall be ignored. This control does not affect the switch's transmission of loopback commands to the far end
STR pportFT1DS0s	1.3.6.1.4.1.277.1.4.2.1.149	DisplayString	read-write	DS0 usage bitmask for Fractional T1/E1 data rates.
INT pportIMUXCnt	1.3.6.1.4.1.277.1.4.2.1.150	INTEGER	read-write	DS3 Inverse Multiplexer counter value - specifies number of idle cells to insert by the outbound process Hardware.
INT pportds1PMConfigThresh	1.3.6.1.4.1.277.1.4.2.1.151	INTEGER	read-write	The setting determines which standard is used for performance monitoring configuration thresholds
INT pportIdleCellType	1.3.6.1.4.1.277.1.4.2.1.152	INTEGER	read-write	The setting determines the type of Idle/unassigned cell transmitted by the pport. 1 -- ATM Forum CLP=0, payload=6A 2 -- ITU CLP=1, payload=6A
INT pportATMTcaInHECErrorUAlertPeriod	1.3.6.1.4.1.277.1.4.2.1.153	INTEGER	read-write	ATM tca ingress HEC error uncorrectable alert period (in min.).
INT pportATMTcaInHECErrorUThresh	1.3.6.1.4.1.277.1.4.2.1.154	INTEGER	read-write	ATM tca ingress HEC error uncorrectable threshold.
INT pportATMTcaEBufOverflowCBRAlertPeriod	1.3.6.1.4.1.277.1.4.2.1.155	INTEGER	read-write	ATM tca egress buffer overflow CBR Alert period (in min)
INT pportATMTcaEBufOverflowCBRThresh	1.3.6.1.4.1.277.1.4.2.1.156	INTEGER	read-write	ATM tca egress buffer overflow CBR threshold.
INT pportATMTcaEBufOverflowABRAlertPeriod	1.3.6.1.4.1.277.1.4.2.1.157	INTEGER	read-write	ATM tca egress buffer overflow ABR alert period (in min)
INT pportATMTcaEBufOverflowABRThresh	1.3.6.1.4.1.277.1.4.2.1.158	INTEGER	read-write	ATM tca egress buffer overflow ABR threshold.
INT pportATMTcaEBufOverflowVBR1AlertPeriod	1.3.6.1.4.1.277.1.4.2.1.159	INTEGER	read-write	ATM tca egress buffer overflow VBR1 alert period (in min)
INT pportATMTcaEBufOverflowVBR1Thresh	1.3.6.1.4.1.277.1.4.2.1.160	INTEGER	read-write	ATM tca egress buffer overflow VBR1 threshold.
INT pportATMTcaEBufOverflowVBR2AlertPeriod	1.3.6.1.4.1.277.1.4.2.1.161	INTEGER	read-write	ATM tca egress buffer overflow VBR2 alert period (in min)
INT pportATMTcaEBufOverflowVBR2Thresh	1.3.6.1.4.1.277.1.4.2.1.162	INTEGER	read-write	ATM tca egress buffer overflow VBR2 threshold.
INT pportATMTcaInFramerFIFOOverflowAlertPeriod	1.3.6.1.4.1.277.1.4.2.1.163	INTEGER	read-write	ATM tca ingress framer FIFO overflow alert period (in min)
INT pportATMTcaInFramerFIFOOverflowThresh	1.3.6.1.4.1.277.1.4.2.1.164	INTEGER	read-write	ATM tca ingress framer FIFO overflow threshold.
INT pportATMTcaELookupFailureAlertPeriod	1.3.6.1.4.1.277.1.4.2.1.165	INTEGER	read-write	ATM tca egress lookup failure alert period (in min)
INT pportATMTcaELookupFailureThresh	1.3.6.1.4.1.277.1.4.2.1.166	INTEGER	read-write	ATM tca egress lookup failure threshold.
INT pportATMTcaEnable	1.3.6.1.4.1.277.1.4.2.1.167	INTEGER	read-write	ATM tca port enable.
INT pportATMTcaId	1.3.6.1.4.1.277.1.4.2.1.168	INTEGER	read-write	This object identifies the the most recently declared pport ATM threshold crossing alert
OCT pportFethAdminMacAddr	1.3.6.1.4.1.277.1.4.2.1.169	OCTET STRING	read-write	The configured MAC address to use for this Fast Ethernet port. Setting this to all zeros will force the port to use the burned in MAC address.
OCT pportFethOperMacAddr	1.3.6.1.4.1.277.1.4.2.1.170	OCTET STRING	read-only	The actual MAC address in use for this Fast Ethernet port.
INT pportConfigAlarmSoakTime	1.3.6.1.4.1.277.1.4.2.1.171	INTEGER	read-write	This is the soak time for configurable alarms. An alarm of this type must persist for this period before it is declared. The time is specified in millseconds units.
INT pportConfigAlarmClearTime	1.3.6.1.4.1.277.1.4.2.1.172	INTEGER	read-write	This is the soak time for configurable alarms. An alarm of this type must remain clear for this period before it is declared to be cleared. The time is specified in millseconds units.
INT pportFethPortCapability	1.3.6.1.4.1.277.1.4.2.1.173	INTEGER	read-write	Selection for the speed (10/100) and mode (half/full duplex) of operation for Fast Ethernet ports.
INT pportVpshapingDiscardCellCount	1.3.6.1.4.1.277.1.4.2.1.174	INTEGER	read-only	Cells discarded due to buffer overflow on this pport because of traffic shaping.
pportTrafficShaperTable	1.3.6.1.4.1.277.1.4.3		not-accessible	A list of Parameters assigned to the 16 traffic shaper parameter conbinations of each pport of the ATM-IWU.
pportTrafficShaperEntry	1.3.6.1.4.1.277.1.4.3.1		not-accessible	Information of a single system reference clock source.
INT pportTrafficShaperIndex	1.3.6.1.4.1.277.1.4.3.1.1	INTEGER	read-write	A positive integer to identify an entry in the pportTrafficShaperTable. The ATM-IWU and CS cards support exactly 16 shapers.
INT pportTrafficShaperPriority	1.3.6.1.4.1.277.1.4.3.1.2	INTEGER	read-write	The priority of the Shaper. Channels tied to a Shaper are served only if no higher priority Shapers await service. 0 ist the highest, 15 the lowest priority.
INT pportTrafficShaperCellRatioDividend	1.3.6.1.4.1.277.1.4.3.1.3	INTEGER	read-write	The quotient of pportTrafficShaperCellRatioDividend and pportTrafficShaperCellRatioDivisor determines the average rate allocated to the shaper. The shaper serves portTrafficShaperCellRatioDividend cells in pportTrafficShaperCellRatioDivisor cell times.
INT pportTrafficShaperCellRatioDivisor	1.3.6.1.4.1.277.1.4.3.1.4	INTEGER	read-write	See pportTrafficShaperCellRatioDividend
INT pportTrafficShaperPeak	1.3.6.1.4.1.277.1.4.3.1.5	INTEGER	read-write	The peak cell rate. It defines the minimum gap (in cell units) between emission of any consecutive cells in this channel.
INT pportTrafficShaperCredit	1.3.6.1.4.1.277.1.4.3.1.6	INTEGER	read-write	Defines the maximum number of credits that can be accumulated by a shaper. This is equivalent to the maximum burst allowed at the peak rate.
lport	1.3.6.1.4.1.277.1.5
lportTable	1.3.6.1.4.1.277.1.5.1		not-accessible	A list of logical port entries. The number of entries is given by the value of ifNumber in MIB-II.
lportEntry	1.3.6.1.4.1.277.1.5.1.1		not-accessible	The logical port entry contains objects relevant to a logical port.
IND lportIfIndex	1.3.6.1.4.1.277.1.5.1.1.1	Index	read-only	The ifIndex value of the corresponding ifEntry.
INT lportSlotId	1.3.6.1.4.1.277.1.5.1.1.2	INTEGER	read-only	The slot number of the board the port is on.
INT lportPportId	1.3.6.1.4.1.277.1.5.1.1.3	INTEGER	read-only	The physical port number of the interface on the board.
INT lportId	1.3.6.1.4.1.277.1.5.1.1.4	INTEGER	read-only	The logical port number of the interface on the physical port. A logical port can be uniquely identified in a Cascade network as { NodeId.lportSlotId.lportPportId.lportId }. lportId is defaulted to 1 (i.e., one-to-one mapping between the physical port and the logical port such as local V.35 or carrier) except the following cases: - For ufr, nfr and trk logical port, it indicates the bundle number for fractional T1 or 24-bundle T1. - For pdntrk logical port, it indicates the dlci over the PDN. Note that pdntrk is not allowed on fractional T1 or 24-bundle T1 physical port.
INT lportLink	1.3.6.1.4.1.277.1.5.1.1.5	INTEGER	read-write	The equipment type of the peer to which the logical port is connected.
INT lportProtocol	1.3.6.1.4.1.277.1.5.1.1.6	INTEGER	read-write	The data link protocol running on the logical port.
INT lportSignal	1.3.6.1.4.1.277.1.5.1.1.7	INTEGER	read-write	The user-network signalling capability for SVC and DLCMI of the logical port. Note that this only applies to fr protocol port.
OCT lportFt1Ds0s	1.3.6.1.4.1.277.1.5.1.1.8	OCTET STRING	read-only	The bit mask indicating the DS0s for the fractional T1/E1 logical port which must be a subset of the corresponding pportDs1Ds0s. It's represented by a 32-bit hex char string.
INT lportGlobalDlci	1.3.6.1.4.1.277.1.5.1.1.9	INTEGER	read-write	The global DLCI correspondent to the interface if the DLCI is globally significant in the network. Note that this object is read-write only during creation, and read-only after creation.
INT lportDlcmiStd	1.3.6.1.4.1.277.1.5.1.1.10	INTEGER	read-write	This variable states which Data Link Connection Management scheme is active (and by implication, what DLCI it uses) on the Frame Relay interface.
INT lportDlciAddrFmt	1.3.6.1.4.1.277.1.5.1.1.11	INTEGER	read-only	This variable states which address format is in use on the Frame Relay interface.
INT lportDlciAddrLen	1.3.6.1.4.1.277.1.5.1.1.12	INTEGER	read-only	This variable states which address length in octets. In the case of Q922 format, the length indicates the entire length of the address including the control portion.
INT lportMaxFramesize	1.3.6.1.4.1.277.1.5.1.1.13	INTEGER	read-only	The maximum frame size supported on the interface. Currently it's not used.
INT lportDceVerifTimer	1.3.6.1.4.1.277.1.5.1.1.14	INTEGER	read-write	The polling verification timer (secs) on the DCE interface. If the port is configured as a DXI/SNI, then this MIB object defines the heartbeat poll timer setting.
INT lportDceErrorThresh	1.3.6.1.4.1.277.1.5.1.1.15	INTEGER	read-write	The error threshold on the DCE interface. If the port is configured as a DXI/SNI, then this MIB object defines the heartbeat poll No Ack threshold setting.
INT lportDceEventCount	1.3.6.1.4.1.277.1.5.1.1.16	INTEGER	read-write	The monitored events count on the DCE interface.
INT lportDteErrorThresh	1.3.6.1.4.1.277.1.5.1.1.17	INTEGER	read-write	The error threshold on the DTE interface.
INT lportDteEventCount	1.3.6.1.4.1.277.1.5.1.1.18	INTEGER	read-write	The monitored events count on the DTE interface.
INT lportDtePollTimer	1.3.6.1.4.1.277.1.5.1.1.19	INTEGER	read-write	The link status polling timer (secs) on the DTE interface.
INT lportDteFullCounter	1.3.6.1.4.1.277.1.5.1.1.20	INTEGER	read-write	The full status polling counter on the DTE interface.
INT lportDteMulticast	1.3.6.1.4.1.277.1.5.1.1.21	INTEGER	read-only	The multicast capability of the interface.
IP lportTrkRnode	1.3.6.1.4.1.277.1.5.1.1.22	IpAddress	read-write	Node at the other end of the trunk. This object is read-write only during lport creation, and read-only thereafter.
INT lportTrkRlport	1.3.6.1.4.1.277.1.5.1.1.23	INTEGER	read-write	Logical port (IfIndex) at the other end of the trunk. This
INT lportCongestState	1.3.6.1.4.1.277.1.5.1.1.24	INTEGER	read-only	Congestion State for the logical port.
INT lportQP1Len	1.3.6.1.4.1.277.1.5.1.1.25	INTEGER	read-only	Priority-1 queue length (number of packets) in xmit buffer.
INT lportQP2Len	1.3.6.1.4.1.277.1.5.1.1.26	INTEGER	read-only	Priority-2 queue length (number of packets) in xmit buffer.
INT lportQP3Len	1.3.6.1.4.1.277.1.5.1.1.27	INTEGER	read-only	Priority-3 queue length (number of packets) in xmit buffer.
INT lportQP4Len	1.3.6.1.4.1.277.1.5.1.1.28	INTEGER	read-only	Priority-4 queue length (number of packets) in xmit buffer.
TIK lportErrTime	1.3.6.1.4.1.277.1.5.1.1.29	TimeTicks	read-only	The value of sysUpTime at which the last error was detected.
INT lportErrType	1.3.6.1.4.1.277.1.5.1.1.30	INTEGER	read-only	The type of error that was last seen on this interface.
OCT lportErrData	1.3.6.1.4.1.277.1.5.1.1.31	OCTET STRING	read-only	An octet string containing as much of the error packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desirable to include all information up to the PDU.
INT lportDiagTestId	1.3.6.1.4.1.277.1.5.1.1.32	INTEGER	read-write	Identification for the diagnostics tests to be run.
INT lportDiagTestRuns	1.3.6.1.4.1.277.1.5.1.1.33	INTEGER	read-write	Number of passes of the diagnostics tests to be run. The default value is 1.
INT lportDataRate	1.3.6.1.4.1.277.1.5.1.1.34	INTEGER	read-write	An estimate of the logical port's data rate in bits per second.
INT lportTrkStatus	1.3.6.1.4.1.277.1.5.1.1.35	INTEGER	read-only	The current state of the trunk. The btdefined state only applies to backup trunks.
INT lportSevCongests	1.3.6.1.4.1.277.1.5.1.1.36	INTEGER	read-only	The cumulative number of times that the lport's congestion state has changed from mildly-congested to severely-congested since the last reset.
INT lportAbsCongests	1.3.6.1.4.1.277.1.5.1.1.37	INTEGER	read-only	The cumulative number of times that the lport's congestion state has changed from severely-congested to absolutely- congested since the last reset.
INT lportTrkOverhead	1.3.6.1.4.1.277.1.5.1.1.38	INTEGER	read-write	An estimate of the overhead (headers and internal control messages) in trunking user data in terms of a percentage of the configured trunk bandwidth.
INT lportTrkUtil	1.3.6.1.4.1.277.1.5.1.1.39	INTEGER	read-write	An estimate of the real utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
INT lportVAvailbw	1.3.6.1.4.1.277.1.5.1.1.40	INTEGER	read-only	Currently available virtual trunk bandwidth.
TIK lportTrkLastTimeChange	1.3.6.1.4.1.277.1.5.1.1.41	TimeTicks	read-only	The sysUpTime value when the trunk was last changed to the current status.
INT lportCongestRate	1.3.6.1.4.1.277.1.5.1.1.42	INTEGER	read-only	The rate (%) of entering severely or absolutely congested states in the last one minute interval.
INT lportCongestRateThresh	1.3.6.1.4.1.277.1.5.1.1.43	INTEGER	read-write	The alert threshold (%) for the CongestRate; trap will be sent when exceeded.
INT lportDiagState	1.3.6.1.4.1.277.1.5.1.1.44	INTEGER	read-write	The current state of the diagnostic on this logical port.
OCT lportDiagOptionStr	1.3.6.1.4.1.277.1.5.1.1.45	OCTET STRING	read-write	Optional parameters to the diagnostic.
INT lportDiagPassCount	1.3.6.1.4.1.277.1.5.1.1.46	INTEGER	read-only	Number of successful diagnostic passes.
INT lportDiagFailCount	1.3.6.1.4.1.277.1.5.1.1.47	INTEGER	read-only	Number of failed diagnostic passes.
STR lportDiagResultStr	1.3.6.1.4.1.277.1.5.1.1.48	DisplayString	read-only	Description of last diagnostic failure.
INT lportDs0BitStuff	1.3.6.1.4.1.277.1.5.1.1.49	INTEGER	read-write	Is bit stuffing enabled on this lport?
INT lportErrorThreshold	1.3.6.1.4.1.277.1.5.1.1.50	INTEGER	read-write	The per minute error threshold before a link error trap is sent.
INT lportUnsyncBandwidth	1.3.6.1.4.1.277.1.5.1.1.51	INTEGER	read-only	The accumulated allocated/deallocated bandwidth which has not been propagated by OSPF yet.
CTR lportDTEInStatusFrames	1.3.6.1.4.1.277.1.5.1.1.52	Counter	read-only	The number of LMI STATUS frames received from the DCE since the last system reset. The count includes link integrity verification frames only.
CTR lportDTEInFullStatusFrames	1.3.6.1.4.1.277.1.5.1.1.53	Counter	read-only	The number of LMI Full STATUS frames received from the DTE since the last system reset.
CTR lportDTEInAsyncStatusFrames	1.3.6.1.4.1.277.1.5.1.1.54	Counter	read-only	The number of asynchronous LMI Status frames received from the DTE since the last system reset. For LMI Rev 1, these are Update STATUS frames. For ANSI Annex D and CCITT Annex A these are Asynchronous STATUS frames.
CTR lportDTEInErrorFrames	1.3.6.1.4.1.277.1.5.1.1.55	Counter	read-only	The number of LMI frames received containing protocol errors.
CTR lportDTEOutPollFrames	1.3.6.1.4.1.277.1.5.1.1.56	Counter	read-only	The number of LMI Status Enquiry frames transmitted since the last system reset.
CTR lportDTEPollErrorCounts	1.3.6.1.4.1.277.1.5.1.1.57	Counter	read-only	The number of DTE in-channel signaling link reliability errors (i.e. LMI Status Enquiry frames that were not responded to, sequence number errors) since the last system reset.
CTR lportDTEFailCounts	1.3.6.1.4.1.277.1.5.1.1.58	Counter	read-only	The number of times since the last system reset LMI has declared the DTE side of the link down due to excessive errors.
INT lportDTEFailReason	1.3.6.1.4.1.277.1.5.1.1.59	INTEGER	read-only	The LMI failure reason. If the rate of LMI detected errors exceeds the threshold, this contains the cause of the most recent error.
INT lportDTEOperStatus	1.3.6.1.4.1.277.1.5.1.1.60	INTEGER	read-only	The operational status of the DTE side of LMI on this link.
CTR lportDCEInPollFrames	1.3.6.1.4.1.277.1.5.1.1.61	Counter	read-only	The number of LMI poll frames received from the DTE since the last system reset.
CTR lportDCEInErrorFrames	1.3.6.1.4.1.277.1.5.1.1.62	Counter	read-only	The number of LMI frames received containing protocol errors.
CTR lportDCEOutStatusFrames	1.3.6.1.4.1.277.1.5.1.1.63	Counter	read-only	The number of LMI STATUS frames transmitted since the last system reset. The count includes link integrity verification frames only.
CTR lportDCEOutFullStatusFrames	1.3.6.1.4.1.277.1.5.1.1.64	Counter	read-only	The number of LMI Full STATUS frames transmitted since the last system reset.
CTR lportDCEOutAsyncStatusFrames	1.3.6.1.4.1.277.1.5.1.1.65	Counter	read-only	The number of asynchronous LMI Status frames transmitted since the last system reset. For LMI Rev 1, these are Update STATUS frames. For ANSI Annex D and CCITT Annex A these are Asynchronous STATUS frames.
CTR lportDCEPollErrorCounts	1.3.6.1.4.1.277.1.5.1.1.66	Counter	read-only	The number of DCE in-channel signaling link reliability errors (i.e. timeouts waiting for LMI Status Enquiry frames, sequence number errors) since the last system reset.
CTR lportDCEFailCounts	1.3.6.1.4.1.277.1.5.1.1.67	Counter	read-only	The number of times since the last system reset LMI has declared the DCE side of the link down due to excessive errors.
INT lportDCEFailReason	1.3.6.1.4.1.277.1.5.1.1.68	INTEGER	read-only	The LMI failure reason. If the rate of LMI detected errors exceeds the threshold, this contains the cause of the most recent error.
INT lportDCEOperStatus	1.3.6.1.4.1.277.1.5.1.1.69	INTEGER	read-only	The operational status of the DCE side of LMI on this link.
INT lportDCEOperDlcmiStd	1.3.6.1.4.1.277.1.5.1.1.70	INTEGER	read-only	This variable states which Data Link Connection Management scheme is actually being run on this link. This is used for DCE links configured for AutoDetect and indicates the LMI standard used in the last poll received from the DTE.
CTR lportLMIInErrorFrames	1.3.6.1.4.1.277.1.5.1.1.71	Counter	read-only	The number of total frames received with an error. For NNI links this is the sum of lportDTEInErrorFrames and lportDCEInErrorFrames.
INT lportDCEnN4	1.3.6.1.4.1.277.1.5.1.1.72	INTEGER	read-write	This variable specifies the maximum number of LMI Status Enquiry frames that can be received from a DTE within time interval lportDCEnT3. This is only valid on lports using LMIREV1.
INT lportDCEnT3	1.3.6.1.4.1.277.1.5.1.1.73	INTEGER	read-write	This variable specifies the time interval (secs) used to determine if lportDCEnN4 an excess number (lportDCEnN4) of Status Enquiry messages are received. This is only valid on lports using LMIREV1.
INT lportXmitLatencyThreshold	1.3.6.1.4.1.277.1.5.1.1.74	INTEGER	read-write	Outbound frames are allowed on the transmit commit queue when the commit queue falls below this threshold (in microseconds).
INT lportXmitRefillPriority0Percentage	1.3.6.1.4.1.277.1.5.1.1.75	INTEGER	read-write	Percentage of time the transmit queue is refilled in priority order 0, 1, 2, 3.
INT lportXmitRefillPriority1Percentage	1.3.6.1.4.1.277.1.5.1.1.76	INTEGER	read-write	Percentage of time the transmit queue is refilled in priority order 1, 2, 3, 0.
INT lportXmitRefillPriority2Percentage	1.3.6.1.4.1.277.1.5.1.1.77	INTEGER	read-write	Percentage of time the transmit queue is refilled in priority order 2, 3, 0, 1.
INT lportXmitRefillPriority3Percentage	1.3.6.1.4.1.277.1.5.1.1.78	INTEGER	read-write	Percentage of time the transmit queue is refilled in priority order 3, 0, 1, 2.
INT lportXmitDiscardLow	1.3.6.1.4.1.277.1.5.1.1.79	INTEGER	read-write	Priority holding queue low water discard threshold. Discarding stops when holding queue hits this level.
INT lportSevereThreshold	1.3.6.1.4.1.277.1.5.1.1.80	INTEGER	read-write	Severe congestion level. Outbound red and amber packets are discarded when the transmit queue hits this threshold.
INT lportMildThreshold	1.3.6.1.4.1.277.1.5.1.1.81	INTEGER	read-write	Mild congestion level. Outbound red packets are discarded when the transmit queue hits this threshold.
INT lportTrkKeepAliveTimer	1.3.6.1.4.1.277.1.5.1.1.86	INTEGER	read-write	Send a keep-alive packet after this many seconds. These packets are sent on trunk links only. The range is 0 thru 15, with zero meaning the keep-alive protocol is disabled. The default is one.
INT lportTrkKeepAliveErrorThreshold	1.3.6.1.4.1.277.1.5.1.1.87	INTEGER	read-write	Declare the interface down after this many keep-alive packets in a row are missed. The default is five.
INT lportIgCutThruStatus	1.3.6.1.4.1.277.1.5.1.1.88	INTEGER	read-write	Enable ingress cut-thru on this user lport. Default is disabled.
INT lportEgCutThruStatus	1.3.6.1.4.1.277.1.5.1.1.89	INTEGER	read-write	Enable egress cut-thru on this user lport. Default is disabled.
INT lportEgCutThruThresh	1.3.6.1.4.1.277.1.5.1.1.90	INTEGER	read-write	Egress cut thru threshold - start transmitting a frame on a user port after this many segments have arrived.
INT lportFrameRelayTrkEnable	1.3.6.1.4.1.277.1.5.1.1.91	INTEGER	read-write	Allow Frame Relay Trunks on the user link.
INT lportSmdsSsiIf	1.3.6.1.4.1.277.1.5.1.1.92	INTEGER	read-write	The interface number of the SSI which this DXI/SNI is multiplexed to.
INT lportSmdsSsiSlot	1.3.6.1.4.1.277.1.5.1.1.93	INTEGER	read-write	The slot of the SSI which this DXI/SNI is multiplexed to.
INT lportSmdsScrnId	1.3.6.1.4.1.277.1.5.1.1.94	INTEGER	read-write	The ID of address screen for this interface.
INT lportSmdsIaScrnOp	1.3.6.1.4.1.277.1.5.1.1.95	INTEGER	read-write	Individual address screen operation.
INT lportSmdsGaScrnOp	1.3.6.1.4.1.277.1.5.1.1.96	INTEGER	read-write	Group address screen operation.
OCT lportSmdsIaScrnMap	1.3.6.1.4.1.277.1.5.1.1.97	OCTET STRING	read-write	The individual address screen member bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit map. The bit position of each bit in this bit map represent a screen member ID. The most significant bit is corresponding to group address ID 1. For get response, The whole string is the bit map.
OCT lportSmdsGaScrnMap	1.3.6.1.4.1.277.1.5.1.1.98	OCTET STRING	read-write	The group address screen member bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit map. The bit position of each bit in this bit map represent a screen member ID. The most significant bit is corresponding to group address ID 1. For get response, The whole string is the bit map.
OCT lportSmdsTrkAddr	1.3.6.1.4.1.277.1.5.1.1.99	OCTET STRING	read-write	SMDS address. For SSI feeder port, this address is the local address of all SMDS optimim paths associated with this SSI feeder port. For SSI Optimum path port, this address is the remote address of this SSI optimum path. The 4 most significant bits are 1100. The following 4 bits are 0001. The following 5 bytes are the 10 digits number in BCD format. The following 16 bits are padded with 1's
INT lportSmdsCrc	1.3.6.1.4.1.277.1.5.1.1.100	INTEGER	read-write	CRC which CPE generates.
INT lportSmdsCpePoll	1.3.6.1.4.1.277.1.5.1.1.101	INTEGER	read-write	Whether CPE supports heart beat poll or not.
INT lportSmdsPduCheck	1.3.6.1.4.1.277.1.5.1.1.102	INTEGER	read-write	turn of/off the detailed SIP3 PDU error checking.
CTR lportSmdsCntOutFrDxi2HbPolls	1.3.6.1.4.1.277.1.5.1.1.103	Counter	read-write	Number of DXI2 heart beat poll frames transmitted.
CTR lportSmdsCntOutByteDxi2HbPolls	1.3.6.1.4.1.277.1.5.1.1.104	Counter	read-write	Total number of octets in DXI2 heart beat poll frames transmitted.
CTR lportSmdsCntInFrDxi2HbPolls	1.3.6.1.4.1.277.1.5.1.1.105	Counter	read-write	Number of DXI2 heart beat poll frames received.
CTR lportSmdsCntInByteDxi2HbPolls	1.3.6.1.4.1.277.1.5.1.1.106	Counter	read-write	Total number of octets in DXI2 heart beat poll frames received.
CTR lportSmdsCntOutFrSip3s	1.3.6.1.4.1.277.1.5.1.1.107	Counter	read-write	Number of SIP3 frames transmitted.
CTR lportSmdsCntOutByteSip3s	1.3.6.1.4.1.277.1.5.1.1.108	Counter	read-write	Total number of octets in SIP3 frames transmitted.
CTR lportSmdsCntInFrSip3s	1.3.6.1.4.1.277.1.5.1.1.109	Counter	read-write	Number of SIP3 frames received.
CTR lportSmdsCntInByteSip3s	1.3.6.1.4.1.277.1.5.1.1.110	Counter	read-write	Total number of octets in SIP3 frames received.
CTR lportSmdsCntDxi2LinkIdInvalids	1.3.6.1.4.1.277.1.5.1.1.111	Counter	read-write	Number of instances that DXI2 link ID is invalid.
CTR lportSmdsCntDxi2StationIdInvalids	1.3.6.1.4.1.277.1.5.1.1.112	Counter	read-write	Number of instances that DXI2 station ID is invalid.
CTR lportSmdsCntDxi2CrInvalids	1.3.6.1.4.1.277.1.5.1.1.113	Counter	read-write	Number of instances that DXI2 command/response field is invalid.
CTR lportSmdsCntDxi2AeInvalids	1.3.6.1.4.1.277.1.5.1.1.114	Counter	read-write	Number of instances that DXI2 address extension field is invalid.
CTR lportSmdsCntDxi2CtrlInvalids	1.3.6.1.4.1.277.1.5.1.1.115	Counter	read-write	Number of instances that DXI2 control field is invalid.
CTR lportSmdsCntDxi2FrameSizeErrors	1.3.6.1.4.1.277.1.5.1.1.116	Counter	read-write	Number of instances there is a DXI2 frame size error.
CTR lportSmdsCntSip3RsvdInvalids	1.3.6.1.4.1.277.1.5.1.1.117	Counter	read-write	Number of instances that SIP3 reserved field in header is invalid.
CTR lportSmdsCntSip3BetagMismatchs	1.3.6.1.4.1.277.1.5.1.1.118	Counter	read-write	Number of instances that SIP3 BE tag is not macthed.
CTR lportSmdsCntSip3BasizeIncorrects	1.3.6.1.4.1.277.1.5.1.1.119	Counter	read-write	Number of instances that SIP3 BA size is incorrect.
CTR lportSmdsCntSip3BasizeInvalids	1.3.6.1.4.1.277.1.5.1.1.120	Counter	read-write	Number of instances that SIP3 BA size is invalid.
CTR lportSmdsCntSip3DaTypeInvalids	1.3.6.1.4.1.277.1.5.1.1.121	Counter	read-write	Number of instances that SIP3 destination address type is invalid.
CTR lportSmdsCntSip3DaInvalids	1.3.6.1.4.1.277.1.5.1.1.122	Counter	read-write	Number of instances that SIP3 destination address is invalid.
CTR lportSmdsCntSip3SaTypeInvalids	1.3.6.1.4.1.277.1.5.1.1.123	Counter	read-write	Number of instances that SIP3 source address type is invalid.
CTR lportSmdsCntSip3SaInvalids	1.3.6.1.4.1.277.1.5.1.1.124	Counter	read-write	Number of instances that SIP3 source address is invalid.
CTR lportSmdsCntSip3BasizeMismatchs	1.3.6.1.4.1.277.1.5.1.1.125	Counter	read-write	Number of instances that SIP3 BA sizes in the header and trailer are not matched.
CTR lportSmdsCntSip3HeLenInvalids	1.3.6.1.4.1.277.1.5.1.1.126	Counter	read-write	Number of instances that SIP3 header extension length is invalid.
CTR lportSmdsCntSip3HeVersionInvalids	1.3.6.1.4.1.277.1.5.1.1.127	Counter	read-write	Number of instances that SIP3 header extension version is invalid.
CTR lportSmdsCntSip3HeCarrierInvalids	1.3.6.1.4.1.277.1.5.1.1.128	Counter	read-write	Number of instances that SIP3 header extension carrier is invalid.
CTR lportSmdsCntSip3Crc32Errors	1.3.6.1.4.1.277.1.5.1.1.129	Counter	read-write	Number of SIP3 CRC errors.
CTR lportSmdsCntSip3TRsvdInvalids	1.3.6.1.4.1.277.1.5.1.1.130	Counter	read-write	Number of instances that SIP3 reserved field in trailer is invalid.
CTR lportSmdsCntSaNotFounds	1.3.6.1.4.1.277.1.5.1.1.131	Counter	read-write	Number of instances that source address not found.
CTR lportSmdsCntSaValidationFails	1.3.6.1.4.1.277.1.5.1.1.132	Counter	read-write	Number of instances that source address validation failed.
CTR lportSmdsCntSaDaOnSamePorts	1.3.6.1.4.1.277.1.5.1.1.133	Counter	read-write	Number of instances that source address and destination addresses are on the same port.
CTR lportSmdsCntDaSsiMismacths	1.3.6.1.4.1.277.1.5.1.1.134	Counter	read-write	Obsolete.
CTR lportSmdsCntSsiProvisionErrors	1.3.6.1.4.1.277.1.5.1.1.135	Counter	read-write	Obsolete.
CTR lportSmdsCntDstIaNotFounds	1.3.6.1.4.1.277.1.5.1.1.136	Counter	read-write	Number of instances that destination individual address not found.
CTR lportSmdsCntDstGaNotFounds	1.3.6.1.4.1.277.1.5.1.1.137	Counter	read-write	Number of instances that destination group address not found.
CTR lportSmdsCntSrcIaScrnFails	1.3.6.1.4.1.277.1.5.1.1.138	Counter	read-write	Number of instances that source individual address screening failed.
CTR lportSmdsCntDstIaScrnFails	1.3.6.1.4.1.277.1.5.1.1.139	Counter	read-write	Number of instances that destination individual address screening failed.
CTR lportSmdsCntDstGaScrnFails	1.3.6.1.4.1.277.1.5.1.1.140	Counter	read-write	Number of instances that destination group address screening failed.
CTR lportSmdsTotalDiscards	1.3.6.1.4.1.277.1.5.1.1.141	Counter	read-write	total number of discards.
INT lportSmdsSsiNode	1.3.6.1.4.1.277.1.5.1.1.142	INTEGER	read-write	The Node of the SSI which this DXI/SNI is multiplexed to.
INT lportBilling	1.3.6.1.4.1.277.1.5.1.1.143	INTEGER	read-write	This object defines the ability to enable and disable billing on this logical port (for SMDS this must be a DXI). When the value of nodeBilling is 'enabled', the value of this object will take precedence. When the value of nodeBilling is 'disabled', the value of this object will be overridden and billing will be disabled. The default value of this object is 'disabled'.
INT lportSmdsReserved144	1.3.6.1.4.1.277.1.5.1.1.144	INTEGER	read-write	reserved! ignore!
INT lportLinkStatus	1.3.6.1.4.1.277.1.5.1.1.145	INTEGER	read-write	Link protocol status. The Link protocol may be frame relay LMI, DXI heart beat poll, PPP LCP, etc, depends on the lport type.
INT lportLMIDelay	1.3.6.1.4.1.277.1.5.1.1.146	INTEGER	read-write	The number of seconds 1-9 to buffer (or initiate) a FR LMI async update (or ATM OAM alarms) to allow filtering of LMI async events. Zero (0) indicates that no buffering is done (all updates are immediate) and 255 indicates that no updates are sent.
INT lportCRC	1.3.6.1.4.1.277.1.5.1.1.147	INTEGER	read-write	Lport CRC selection: 0 - 16 bit CRC 1 - 32 bit CRC
OCT lportSmdsMulticastGa	1.3.6.1.4.1.277.1.5.1.1.148	OCTET STRING	read-write	The Multicast Group Address is the smds broadcast address which is used to get smds address from its IP address.
IP lportSmdsMulticastIpAddr	1.3.6.1.4.1.277.1.5.1.1.149	IpAddress	read-write	This IP address is this logical port's IP address.
INT lportAtmVPI	1.3.6.1.4.1.277.1.5.1.1.150	INTEGER	read-write	VPI value in the ATM cell header: ATM DXI with HSSI IOP VPI (4 lsb bit) range: 0 - 15 ATM UNI DS3/E3 IOP VPI (4 lsb bit) range: 0 - 15
INT lportAtmVCI	1.3.6.1.4.1.277.1.5.1.1.151	INTEGER	read-write	VCI value in the ATM cell header: ATM DXI with HSSI IOP VCI (6 lsb bit) range: 0 - 63 ATM UNI DS3/E3 IOP VCI (8 lsb bit) range: 0 - 255
INT lportPeakCellRateindex	1.3.6.1.4.1.277.1.5.1.1.152	INTEGER	read-write	Peak cell rate queue index
INT lportSustCellRate	1.3.6.1.4.1.277.1.5.1.1.153	INTEGER	read-write	Sustainable cell rate in cell/second
INT lportBurstTolerance	1.3.6.1.4.1.277.1.5.1.1.154	INTEGER	read-write	Burst Tolerance in multiple of 32 cells
INT lportBuTrkOnFailure	1.3.6.1.4.1.277.1.5.1.1.155	INTEGER	read-write	Enables or disables trunk backup due to link down.
INT lportTrkFailureThrsh	1.3.6.1.4.1.277.1.5.1.1.156	INTEGER	read-write	The number of seconds a primary trunk must remain down for trunk backup to be initiated.
INT lportTrkRestThrsh	1.3.6.1.4.1.277.1.5.1.1.157	INTEGER	read-write	The number of seconds a primary trunk must remain up for trunk backup to be terminated
INT lportBuTrkRetryInt	1.3.6.1.4.1.277.1.5.1.1.158	INTEGER	read-write	The number of seconds between backup trunk call setup retries.
INT lportBuTrkRetryNum	1.3.6.1.4.1.277.1.5.1.1.159	INTEGER	read-write	The number of backup trunk call setup tries per call setup cycle.
INT lportBuTrkCycleInt	1.3.6.1.4.1.277.1.5.1.1.160	INTEGER	read-write	The number of seconds between backup trunk call setup cycles.
INT lportTrkManualBu	1.3.6.1.4.1.277.1.5.1.1.161	INTEGER	read-write	Initiate or terminate manual backup for a primary trunk. none neither initiate or terminate initCmd initiate operator commanded backup termCmd terminate operator commanded backup initSched initiate scheduled backup termSched terminate scheduled backup
IND lportPrimTrk	1.3.6.1.4.1.277.1.5.1.1.162	Index	read-write	Indicates the primary trunk lportIfIndex for which a backup trunk is serving as a backup. This value is also used to determine trunk type by the following convention: Value Trunk Type 0 Normal lportIfIndex of this trunk Primary other lportIfIndex Backup
INT lportInitCallSetup	1.3.6.1.4.1.277.1.5.1.1.163	INTEGER	read-write	TRUE if node must initiate backup trunk call setup for this primary trunk. Otherwise FALSE.
INT lportBuFailReason	1.3.6.1.4.1.277.1.5.1.1.164	INTEGER	read-only	Indicates the reason for the failure to perform trunk backup.
INT lportQ922Enable	1.3.6.1.4.1.277.1.5.1.1.165	INTEGER	read-write	Set 1 to eanble Q.922 on this port. Q.922 must be enabled if the port is used for SVC.
INT lportQ922State	1.3.6.1.4.1.277.1.5.1.1.166	INTEGER	read-only	Q.922 state. This object only makes sense when Q.922 is enabled.
INT lportTrkPduRevision	1.3.6.1.4.1.277.1.5.1.1.167	INTEGER	read-only	The Trunk PDU Revision number being used over this trunk.
INT lportPVCMgrPduRevision	1.3.6.1.4.1.277.1.5.1.1.168	INTEGER	read-only	The PVC Manager PDU Revision number being used over this trunk.
INT lportDS0LoopStatus	1.3.6.1.4.1.277.1.5.1.1.169	INTEGER	read-only	Indicates whether this logical port has one or more DS0's in loopback
INT lportISDNDuration	1.3.6.1.4.1.277.1.5.1.1.170	INTEGER	read-only	The number of seconds that the ISDN call has been established.
OCT lportISDNSourceAddr	1.3.6.1.4.1.277.1.5.1.1.171	OCTET STRING	read-only	The E.164 address of the source of this ISDN connection.
OCT lportISDNDestAddr	1.3.6.1.4.1.277.1.5.1.1.172	OCTET STRING	read-only	The E.164 address of the destination of this ISDN connection.
IP lportISDNIpAddr	1.3.6.1.4.1.277.1.5.1.1.173	IpAddress	read-only	The Ip Address of the client connected to this B-Channel
INT lportISDNCallRejCause	1.3.6.1.4.1.277.1.5.1.1.174	INTEGER	read-only	The cause of the call rejection - inability to authenticate or pool is busy.
INT lportLastInvalidDLCI	1.3.6.1.4.1.277.1.5.1.1.175	INTEGER	read-only	This item pertains to user frame relay lports only. The frame relay header of the received frame contains a dlci, which uniquely identifies a specific pvc on this lport. When no pvc has been configured, on the lport, that corresponds to the dlci specified in the frame header, the frame is said to have an invalid dlci. This lport entry holds the value of the most recent invalid dlci received on this lport, to be used in troubleshooting faulty configurations.
INT lportTrkProtState	1.3.6.1.4.1.277.1.5.1.1.176	INTEGER	read-only	The current operational state of the link trunk protocol on this link.
INT lportTrkTrafficMix	1.3.6.1.4.1.277.1.5.1.1.177	INTEGER	read-write	The types of traffic allowed over a Cascade trunk.
INT lportNumVC	1.3.6.1.4.1.277.1.5.1.1.178	INTEGER	read-only	The number of VCs going to or through a particular port.
INT lportTrkAdminCost	1.3.6.1.4.1.277.1.5.1.1.179	INTEGER	read-write	The administrative cost of the trunk. Used when routing circuits. Trunks with lower costs are preferred. Value ranges from 1 to 65,535.
INT lportPrivateNet	1.3.6.1.4.1.277.1.5.1.1.180	INTEGER	read-write	If non-zero, indicates the private network that the lport belongs to. If 0, the lport is publicly shared.
INT lportTrkStaticDelay	1.3.6.1.4.1.277.1.5.1.1.181	INTEGER	read-write	The measured round-trip delay of the trunk, in milliseconds. Measured when the trunk last became operational.
INT lportTrkDynamicDelay	1.3.6.1.4.1.277.1.5.1.1.182	INTEGER	read-write	The recently measured round-tip delay of the trunk. May vary from lportTrkStaticDelay due to congestion, or reprovisioning of the underlying media.
INT lportAtmDataRateQoS1	1.3.6.1.4.1.277.1.5.1.1.183	INTEGER	read-write	An estimate of the logical port's data rate in bits per second reserved for QoS class 1.
INT lportAtmDataRateQoS2	1.3.6.1.4.1.277.1.5.1.1.184	INTEGER	read-write	An estimate of the logical port's data rate in bits per second reserved for QoS class 2.
INT lportAtmDataRateQoS3	1.3.6.1.4.1.277.1.5.1.1.185	INTEGER	read-write	An estimate of the logical port's data rate in bits per second reserved for QoS class 3.
INT lportAtmDataRateQoS4	1.3.6.1.4.1.277.1.5.1.1.186	INTEGER	read-write	An estimate of the logical port's data rate in bits per second reserved for QoS class 4.
INT lportOutVAvailbwQoS1	1.3.6.1.4.1.277.1.5.1.1.187	INTEGER	read-only	Current outgoing available virtual bandwidth reserved for QoS class 1.
INT lportOutVAvailbwQoS2	1.3.6.1.4.1.277.1.5.1.1.188	INTEGER	read-only	Current outgoing available virtual bandwidth reserved for QoS class 2.
INT lportOutVAvailbwQoS3	1.3.6.1.4.1.277.1.5.1.1.189	INTEGER	read-only	Current outgoing available virtual bandwidth reserved for QoS class 3.
INT lportOutVAvailbwQoS4	1.3.6.1.4.1.277.1.5.1.1.190	INTEGER	read-only	Current outgoing available virtual bandwidth reserved for QoS class 4.
INT lportInVAvailbwQoS1	1.3.6.1.4.1.277.1.5.1.1.191	INTEGER	read-only	Current incoming available virtual bandwidth reserved for QoS class 1.
INT lportInVAvailbwQoS2	1.3.6.1.4.1.277.1.5.1.1.192	INTEGER	read-only	Current incoming available virtual bandwidth reserved for QoS class 2.
INT lportInVAvailbwQoS3	1.3.6.1.4.1.277.1.5.1.1.193	INTEGER	read-only	Current incoming available virtual bandwidth reserved for QoS class 3.
INT lportInVAvailbwQoS4	1.3.6.1.4.1.277.1.5.1.1.194	INTEGER	read-only	Currently incoming available virtual bandwidth reserved for QoS class 4.
INT lportOutAllocbwQoS1	1.3.6.1.4.1.277.1.5.1.1.195	INTEGER	read-only	Current outgoing allocated bandwidth for QoS Class 1.
INT lportOutAllocbwQoS2	1.3.6.1.4.1.277.1.5.1.1.196	INTEGER	read-only	Current outgoing allocated bandwidth for QoS Class 2.
INT lportOutAllocbwQoS3	1.3.6.1.4.1.277.1.5.1.1.197	INTEGER	read-only	Current outgoing allocated bandwidth for QoS Class 3.
INT lportOutAllocbwQoS4	1.3.6.1.4.1.277.1.5.1.1.198	INTEGER	read-only	Current outgoing allocated bandwidth for QoS Class 4.
INT lportInAllocbwQoS1	1.3.6.1.4.1.277.1.5.1.1.199	INTEGER	read-only	Current incoming allocated bandwidth for QoS Class 1.
INT lportInAllocbwQoS2	1.3.6.1.4.1.277.1.5.1.1.200	INTEGER	read-only	Current incoming allocated bandwidth for QoS Class 2.
INT lportInAllocbwQoS3	1.3.6.1.4.1.277.1.5.1.1.201	INTEGER	read-only	Current incoming allocated bandwidth for QoS Class 3.
INT lportInAllocbwQoS4	1.3.6.1.4.1.277.1.5.1.1.202	INTEGER	read-only	Current incoming allocated bandwidth for QoS Class 4.
INT lportDynamicQoSbw	1.3.6.1.4.1.277.1.5.1.1.203	INTEGER	read-write	Bitmap defining which QoS Classes should have bandwidth allocated dynamically from lportDataRate instead of reserving a percentage up-front.
INT lportSVCRetryTimer	1.3.6.1.4.1.277.1.5.1.1.204	INTEGER	read-write	The duration in seconds (1..255) the network is allowed to re-establish a SVC after network failure before clearing the SVC. A value of (0) indicates continuous retries by the network until the user clears the SVC.
INT lportAtmNetworkType	1.3.6.1.4.1.277.1.5.1.1.205	INTEGER	read-write	Whether this lport is supporting a private or public network.
INT lportAtmRouteMetricQoS1	1.3.6.1.4.1.277.1.5.1.1.206	INTEGER	read-write	Routing metric associated with QoS Class 1.
INT lportAtmRouteMetricQoS2	1.3.6.1.4.1.277.1.5.1.1.207	INTEGER	read-write	Routing metric associated with QoS Class 2.
INT lportAtmRouteMetricQoS3	1.3.6.1.4.1.277.1.5.1.1.208	INTEGER	read-write	Routing metric associated with QoS Class 3.
INT lportAtmRouteMetricQoS4	1.3.6.1.4.1.277.1.5.1.1.209	INTEGER	read-write	Routing metric associated with QoS Class 4.
INT lportIlmiPollTimeout	1.3.6.1.4.1.277.1.5.1.1.210	INTEGER	read-write	The duration in seconds (1..255) the ILMI poll is generated by the network-side UME. A value of 0 set to default polling period of 5 seconds.
INT lportAtmProtocol	1.3.6.1.4.1.277.1.5.1.1.211	INTEGER	read-write	UNI protocol version for this port.
INT lportIlmiAdminStatus	1.3.6.1.4.1.277.1.5.1.1.212	INTEGER	read-write	Administrative state for ILMI function on this port.
INT lportIlmiOperStatus	1.3.6.1.4.1.277.1.5.1.1.213	INTEGER	read-only	Operational status for ILMI function on this port.
CTR lportIlmiPollRetry	1.3.6.1.4.1.277.1.5.1.1.214	Counter	read-write	The number of retries of ILMI poll request will be generated when network-side UME detects loss of ILMI connectivity. A value of 0 sets to default value of 4 times
INT lportAtmVpiBits	1.3.6.1.4.1.277.1.5.1.1.215	INTEGER	read-write	Number of bits of VPI supported.
INT lportAtmVciBits	1.3.6.1.4.1.277.1.5.1.1.216	INTEGER	read-write	Number of bits of VCI supported.
INT lportAtmOamAlarmEnable	1.3.6.1.4.1.277.1.5.1.1.217	INTEGER	read-write	If disabled then OAM alarms are not generated for circuits that are down on this lport.
INT lportInVAvailbw	1.3.6.1.4.1.277.1.5.1.1.218	INTEGER	read-only	Currently available Incoming virtual bandwidth.
INT lportbwUNIPolicy	1.3.6.1.4.1.277.1.5.1.1.219	INTEGER	read-write	The network policy towards requiring sufficient bandwidth at the UNI interface prior to allowing a circuit to be established.
INT lportStarvation	1.3.6.1.4.1.277.1.5.1.1.220	INTEGER	read-only	The CBR card detected a starvation condition on this lport for the extended period defined in Bellcore TA-NWT-001248
INT lportRecOverflow	1.3.6.1.4.1.277.1.5.1.1.221	INTEGER	read-only	The CBR card detected a receive overflow condition on this lport for the extended period defined in Bellcore TA-NWT-001248
INT lportLossOfCellSequence	1.3.6.1.4.1.277.1.5.1.1.222	INTEGER	read-only	The CBR card detected a LOS condition on this lport for the extended period defined in Bellcore TA-NWT-001248
INT lportLossOfStructurePointer	1.3.6.1.4.1.277.1.5.1.1.223	INTEGER	read-only	The CBR card detected a loss of structure pointer condition on this lport for the extended period defined in Bellcore TA-NWT-001248
CTR lportCbrInsDummyCells	1.3.6.1.4.1.277.1.5.1.1.224	Counter	read-only	The number of dummy cells inserted due to cell loss on a constant bit rate (AAL1) interface.
CTR lportRecFifoUnderflowCnt	1.3.6.1.4.1.277.1.5.1.1.225	Counter	read-only	The number of receive FIFO underflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued indicating the lportStarvation.
CTR lportRecFifoOverflowCnt	1.3.6.1.4.1.277.1.5.1.1.226	Counter	read-only	The number of receive FIFO overflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued indicating the receive FIFO overflow.
CTR lportCbrLossOfStructurePointerCnt	1.3.6.1.4.1.277.1.5.1.1.227	Counter	read-only	The object counts how often the structured CBR card detected a loss of the structure pointer since the last reset.
CTR lportCbrLossOfCellSequenceCnt	1.3.6.1.4.1.277.1.5.1.1.228	Counter	read-only	The number of loss of cell sequence since the last reset.
INT lportShaperId	1.3.6.1.4.1.277.1.5.1.1.229	INTEGER	read-write	The shaper to be used for this ATM trunk interworking with frame relay: 1-port ATM-IWU STM-1/STS-3c card -------------------------------- Values: 1..16
INT lportIlmiPrefixScreenMode	1.3.6.1.4.1.277.1.5.1.1.230	INTEGER	read-write	The type of screening to apply against dynamic prefixes received from the peer ILMI entity at this DTE port.
INT lportSmdsPduViolTca	1.3.6.1.4.1.277.1.5.1.1.231	INTEGER	read-write	This object defines the ability to enable and disable SMDS pdu violation traps on this logical port. This functionality applies to the following logical port types: SMDS DXI/SNI DCE SMDS DXI/SNI DTE SMDS SSI DTE SMDS Optimum Trunk Direct Line Trunk The default value of this object is 'disabled'.
INT lportSmdsPduViolThresh	1.3.6.1.4.1.277.1.5.1.1.232	INTEGER	read-write	This object defines the Smds pdu violation threshold for this logical port. The allowable range of threshold values is 1-255. The default value of this object is '10'.
OCT lportSmdsPduHdrSip3SaNotFound	1.3.6.1.4.1.277.1.5.1.1.233	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Not Found. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3SaDaOnSamePort	1.3.6.1.4.1.277.1.5.1.1.234	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Da On Same Port. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3DstGaNotFound	1.3.6.1.4.1.277.1.5.1.1.235	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga Not Found. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3DstIaScrnFail	1.3.6.1.4.1.277.1.5.1.1.236	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia Scrn Fail. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3SaValFail	1.3.6.1.4.1.277.1.5.1.1.237	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Val Fail. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3DstIaNotFound	1.3.6.1.4.1.277.1.5.1.1.238	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia Not Found. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3SrcIaScrnFail	1.3.6.1.4.1.277.1.5.1.1.239	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Src Ia Scrn Fail. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3DstGaScrnFail	1.3.6.1.4.1.277.1.5.1.1.240	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga Scrn Fail. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3SaTypeInvalid	1.3.6.1.4.1.277.1.5.1.1.241	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Type Invalid. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrSip3DaTypeInvalid	1.3.6.1.4.1.277.1.5.1.1.242	OCTET STRING	read-only	This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Da Type Invalid. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OCT lportSmdsPduHdrDxi2LinkIdInvalid	1.3.6.1.4.1.277.1.5.1.1.243	OCTET STRING	read-only	This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Link Id Invalid. The length of this object is 4 bytes.
OCT lportSmdsPduHdrDxi2CrInvalid	1.3.6.1.4.1.277.1.5.1.1.244	OCTET STRING	read-only	This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Cr Invalid. The length of this object is 4 bytes.
OCT lportSmdsPduHdrDxi2CtrlInvalid	1.3.6.1.4.1.277.1.5.1.1.245	OCTET STRING	read-only	This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ctrl Invalid. The length of this object is 4 bytes.
OCT lportSmdsPduHdrDxi2StationIdInvalid	1.3.6.1.4.1.277.1.5.1.1.246	OCTET STRING	read-only	This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Station Id Invalid. The length of this object is 4 bytes.
OCT lportSmdsPduHdrDxi2AeInvalid	1.3.6.1.4.1.277.1.5.1.1.247	OCTET STRING	read-only	This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ae Invalid. The length of this object is 4 bytes.
INT lportDS0FarendLpbkEnabled	1.3.6.1.4.1.277.1.5.1.1.248	INTEGER	read-write	Set a single DS0 into farend loopback 1-24.
INT lportDS0FarendLpbkDisabled	1.3.6.1.4.1.277.1.5.1.1.249	INTEGER	read-write	Set a single DS0 out farend loopback 1-24.
INT lportTrkProtFailureThreshold	1.3.6.1.4.1.277.1.5.1.1.250	INTEGER	read-write	The time, measured in seconds, that Trunk Protocol waits before transitioning the state of an unresponsive trunk from UP to DOWN. Trunk protocol keepalive requests are issued on the trunk lport once per second. This value defines the failure threshold, that is, the number of consecutive requests that must go unanswered before the Trunk Protocol application will declare the trunk lport DOWN.
OCT lportPtr	1.3.6.1.4.1.277.1.5.1.1.251	OCTET STRING	read-only	An octet string indicating the lport pointer.
INT lportISDNPoolUtil	1.3.6.1.4.1.277.1.5.1.1.252	INTEGER	read-only	The percent utilization of the B-channel pool that this b-channel belongs to.
INT lportISDNIpAddrAssignFail	1.3.6.1.4.1.277.1.5.1.1.253	INTEGER	read-only	The cause value for why Ip Address assignment has failed.
INT lportTrkUtilQoS1	1.3.6.1.4.1.277.1.5.1.1.254	INTEGER	read-write	An estimate of the real QoS1 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
INT lportTrkUtilQoS2	1.3.6.1.4.1.277.1.5.1.1.255	INTEGER	read-write	An estimate of the real QoS2 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
INT lportTrkUtilQoS3	1.3.6.1.4.1.277.1.5.1.1.256	INTEGER	read-write	An estimate of the real QoS3 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
INT lportTrkUtilQoS4	1.3.6.1.4.1.277.1.5.1.1.257	INTEGER	read-write	An estimate of the real QoS4 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
CTR lportInCells	1.3.6.1.4.1.277.1.5.1.1.267	Counter	read-only	The total number of cells received
CTR lportOutCells	1.3.6.1.4.1.277.1.5.1.1.268	Counter	read-only	The total number of cells transmitted
ckt	1.3.6.1.4.1.277.1.6
cktTable	1.3.6.1.4.1.277.1.6.1		not-accessible	A table containing information about specific DLCIs, channels and corresponding circuits.
cktEntry	1.3.6.1.4.1.277.1.6.1.1		not-accessible	The information regarding a single Data Link Connection Identifier.
IND cktSrcIfIndex	1.3.6.1.4.1.277.1.6.1.1.1	Index	read-only	The ifIndex value of the corresponding ifEntry.
INT cktSrcDlci	1.3.6.1.4.1.277.1.6.1.1.2	INTEGER	read-only	The DLCI used as the key for the circuit. For local DLCI significance, this is the local DLCI. For Global DLCI significance, this is the remote DLCI.
INT cktPriority	1.3.6.1.4.1.277.1.6.1.1.3	INTEGER	read-write	The priority level (1 through 3) for this circuit.
INT cktCir	1.3.6.1.4.1.277.1.6.1.1.4	INTEGER	read-write	The average number of user data (bits) that the network agrees to transfer over the circuit in one direction, measured over the measurement interval T = cktBc/cktCir.
INT cktBc	1.3.6.1.4.1.277.1.6.1.1.5	INTEGER	read-write	The maximum amount of data (bits) that the network agrees to transfer over the circuit under normal conditions, during the measurement interval.
INT cktBe	1.3.6.1.4.1.277.1.6.1.1.6	INTEGER	read-write	The maximum amount of uncommitted data (bits) that the network will attempt to transfer over the circuit during the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ifSpeed.
INT cktDestNodeId	1.3.6.1.4.1.277.1.6.1.1.7	INTEGER	read-write	The destination node ID for this circuit.
INT cktDestIfIndex	1.3.6.1.4.1.277.1.6.1.1.8	INTEGER	read-write	The interface identifier at the destination node for this circuit.
INT cktDestDlci	1.3.6.1.4.1.277.1.6.1.1.9	INTEGER	read-write	The DLCI which is the destination of the key DLCI. For local DLCI significance, this is the remote DLCI since the key DLCI is the local DLCI. For global significance, this is the local DLCI since the key DLCI is the remote DLCI.
INT cktTos	1.3.6.1.4.1.277.1.6.1.1.10	INTEGER	read-only	The type of service for the circuit. Only committed is supported in the FCS.
INT cktOde	1.3.6.1.4.1.277.1.6.1.1.11	INTEGER	read-write	This variable states whether graceful discard is enabled for the ckt.
INT cktAdminStatus	1.3.6.1.4.1.277.1.6.1.1.12	INTEGER	read-write	The desired state of the ckt.
TIK cktCreationTime	1.3.6.1.4.1.277.1.6.1.1.13	TimeTicks	read-only	The value of sysUpTime when the circuit was created (activated).
TIK cktLastTimeChange	1.3.6.1.4.1.277.1.6.1.1.14	TimeTicks	read-only	The sysUpTime value when the circuit was last changed to the current state.
INT cktVcState	1.3.6.1.4.1.277.1.6.1.1.15	INTEGER	read-only	The current state of the PVC segment in the Cascade network.
INT cktDceState	1.3.6.1.4.1.277.1.6.1.1.16	INTEGER	read-only	The DCE state of the circuit.
INT cktDteStatus	1.3.6.1.4.1.277.1.6.1.1.17	INTEGER	read-only	The DTE status of the circuit.
INT cktRnr	1.3.6.1.4.1.277.1.6.1.1.18	INTEGER	read-only	The receiver's readiness for accepting data flow.
INT cktNiDown	1.3.6.1.4.1.277.1.6.1.1.19	INTEGER	read-only	The state of the network interface.
INT cktDteState	1.3.6.1.4.1.277.1.6.1.1.20	INTEGER	read-only	The DTE state of the circuit.
INT cktOperStatus	1.3.6.1.4.1.277.1.6.1.1.21	INTEGER	read-only	The current operational status of the entire PVC.
INT cktOutForward	1.3.6.1.4.1.277.1.6.1.1.22	INTEGER	read-only	If the value is 1, it means the outbound flow is on.
INT cktRerouteCnt	1.3.6.1.4.1.277.1.6.1.1.23	INTEGER	read-only	The reroute count.
OCT cktVcPtr	1.3.6.1.4.1.277.1.6.1.1.24	OCTET STRING	read-only	An 8-byte Octect string indicating the vc pointer.
INT cktHopCnt	1.3.6.1.4.1.277.1.6.1.1.25	INTEGER	read-only	The count of hops along the circuit path. (Max is 16)
OCT cktPath	1.3.6.1.4.1.277.1.6.1.1.26	OCTET STRING	read-only	The circuit path consisting a sequence of outbound interface indexes at nodes along the established circuit. The format is interface:interface:interface......
INT cktFailReason	1.3.6.1.4.1.277.1.6.1.1.27	INTEGER	read-only	The reason for the PVC establishment failure.
INT cktFailNode	1.3.6.1.4.1.277.1.6.1.1.28	INTEGER	read-only	The node which causes the PVC failure.
INT cktFailPort	1.3.6.1.4.1.277.1.6.1.1.29	INTEGER	read-only	The port on the fail node which causes the PVC failure.
INT cktMcastGroupId	1.3.6.1.4.1.277.1.6.1.1.30	INTEGER	read-write	Multicast group identifier (1..32). This field is 0 for unicast PVCs.
OCT cktMcastMemberList	1.3.6.1.4.1.277.1.6.1.1.31	OCTET STRING	read-write	A list of operations and the affected unicast DLCIs (lportId, cktId)s in a multicast group. The syntax is as follows: [op:dlci,dlci,...,op:dlci,dlci,...] where op can either be delete (0) or add (1)
OCT cktMcastParentGroups	1.3.6.1.4.1.277.1.6.1.1.32	OCTET STRING	read-only	An 8-byte Octect string indicating the parent groups this DLCI belongs to.
CTR cktInFrames	1.3.6.1.4.1.277.1.6.1.1.33	Counter	read-only	The number of inbound frames since the last reset.
CTR cktInDEFrames	1.3.6.1.4.1.277.1.6.1.1.34	Counter	read-only	The number of inbound DE-marked frames since the last reset.
CTR cktInODEFrames	1.3.6.1.4.1.277.1.6.1.1.35	Counter	read-only	The number of inbound ODE-marked frames since the last reset.
CTR cktInFECNFrames	1.3.6.1.4.1.277.1.6.1.1.36	Counter	read-only	The number of inbound frames indicating forward congestion since the last reset.
CTR cktInBECNFrames	1.3.6.1.4.1.277.1.6.1.1.37	Counter	read-only	The number of inbound frames indicating backward congestion since the last reset.
CTR cktInDiscards	1.3.6.1.4.1.277.1.6.1.1.38	Counter	read-only	Number of inbound frames discarded by rate enforcement.
CTR cktInOctets	1.3.6.1.4.1.277.1.6.1.1.39	Counter	read-only	The number of inbound octets since the last reset.
CTR cktInDEOctets	1.3.6.1.4.1.277.1.6.1.1.40	Counter	read-only	The number of inbound DE-marked octets since the last reset.
CTR cktInODEOctets	1.3.6.1.4.1.277.1.6.1.1.41	Counter	read-only	The number of inbound ODE-marked octets since the last reset.
CTR cktOutFrames	1.3.6.1.4.1.277.1.6.1.1.42	Counter	read-only	The number of outbound frames since the last reset.
CTR cktOutDEFrames	1.3.6.1.4.1.277.1.6.1.1.43	Counter	read-only	The number of outbound DE-marked frames since the last reset.
CTR cktOutODEFrames	1.3.6.1.4.1.277.1.6.1.1.44	Counter	read-only	The number of outbound ODE-marked frames since the last reset.
CTR cktOutFECNFrames	1.3.6.1.4.1.277.1.6.1.1.45	Counter	read-only	The number of outbound FECN-marked frames since the last reset.
CTR cktOutBECNFrames	1.3.6.1.4.1.277.1.6.1.1.46	Counter	read-only	The number of outbound BECN-marked frames since the last reset.
CTR cktOutOctets	1.3.6.1.4.1.277.1.6.1.1.47	Counter	read-only	The number of outbound octets since the last reset.
CTR cktOutDEOctets	1.3.6.1.4.1.277.1.6.1.1.48	Counter	read-only	The number of outbound DE-marked octets since the last reset.
CTR cktOutODEOctets	1.3.6.1.4.1.277.1.6.1.1.49	Counter	read-only	The number of outbound ODE-marked octets since the last reset.
CTR cktOutLostFrames	1.3.6.1.4.1.277.1.6.1.1.50	Counter	read-only	The number of outbound frames that have been lost since the last reset.
CTR cktOutLostDEFrames	1.3.6.1.4.1.277.1.6.1.1.51	Counter	read-only	The number of outbound DE-marked frames that have been lost since the last reset.
CTR cktOutLostODEFrames	1.3.6.1.4.1.277.1.6.1.1.52	Counter	read-only	The number of outbound ODE-marked frames that have been lost since the last reset.
CTR cktOutLostOctets	1.3.6.1.4.1.277.1.6.1.1.53	Counter	read-only	The number of outbound octets that have been lost since the last reset.
CTR cktOutLostDEOctets	1.3.6.1.4.1.277.1.6.1.1.54	Counter	read-only	The number of outbound DE-marked octets that have been lost since the last reset.
CTR cktOutLostODEOctets	1.3.6.1.4.1.277.1.6.1.1.55	Counter	read-only	The number of outbound ODE-marked octets that have been lost since the last reset.
INT cktRtMinDelay	1.3.6.1.4.1.277.1.6.1.1.56	INTEGER	read-only	The minimum round-trip delay (micro-seconds).
INT cktRtMaxDelay	1.3.6.1.4.1.277.1.6.1.1.57	INTEGER	read-only	The maximum round-trip delay (micro-seconds).
INT cktRtAvgDelay	1.3.6.1.4.1.277.1.6.1.1.58	INTEGER	read-only	The average round-trip delay (micro-seconds).
INT cktDiagTestId	1.3.6.1.4.1.277.1.6.1.1.59	INTEGER	read-write	Identification for the diagnostics tests to be run.
INT cktDiagTestRuns	1.3.6.1.4.1.277.1.6.1.1.60	INTEGER	read-write	Number of passes of the diagnostics tests to be run. The default value is 1.
INT cktHelloCounter	1.3.6.1.4.1.277.1.6.1.1.61	INTEGER	read-only	Number of PVC hello pdu frames received in the VC entry of the called side.
INT cktHelloAckCounter	1.3.6.1.4.1.277.1.6.1.1.62	INTEGER	read-only	Number of PVC hello Ack pdu frames received in the VC entry of the calling side.
OCT cktDefinedPath	1.3.6.1.4.1.277.1.6.1.1.63	OCTET STRING	read-write	User defined path. in the format of Nx,x,x,Nx,.... If x is not prefixed with 'N', x is an interface ID. If x is prefixed with `N`, x is a node ID.
INT cktDefinedPathCount	1.3.6.1.4.1.277.1.6.1.1.64	INTEGER	read-only	User defined path hop count.
INT cktDefinedPathEnable	1.3.6.1.4.1.277.1.6.1.1.65	INTEGER	read-write	If set to 1, it means there is an user defined path for this circuit and it is enabled.
INT cktDefinedPathAltOption	1.3.6.1.4.1.277.1.6.1.1.66	INTEGER	read-write	If set to 1, it means that if the user defined path fails, use the ospf-determined path.
INT cktUsingDefinedPath	1.3.6.1.4.1.277.1.6.1.1.67	INTEGER	read-only	If set to 1, it indicates the PVC is currently using the defined path.
INT cktTryAltPath	1.3.6.1.4.1.277.1.6.1.1.68	INTEGER	read-only	If set to 1, it means the inactive PVC will be activated on the ospf-determined path in the next retry.
INT cktNotVirgin	1.3.6.1.4.1.277.1.6.1.1.69	INTEGER	read-only	If set to 1, it means this VC entry has been successfuly activated before.
INT cktInForward	1.3.6.1.4.1.277.1.6.1.1.70	INTEGER	read-only	If the value is 1, it means the inbound flow is OK.
INT cktBtusSeg	1.3.6.1.4.1.277.1.6.1.1.71	INTEGER	read-write	Number of Bus xmit units per data segment
CTR cktInSegmentsDiscards	1.3.6.1.4.1.277.1.6.1.1.72	Counter	read-only	Number of segments received that were discarded because of frame reassembly errors.
INT cktAtmVPI	1.3.6.1.4.1.277.1.6.1.1.73	INTEGER	read-write	VPI value in the ATM cell header: ATM DXI with HSSI IOP VPI (4 lsb bit) range: 0 - 15 ATM UNI DS3/E3 IOP VPI (4 lsb bit) range: 0 - 15 T1 ATM 4 lsb range 0-15 ATM-IWU STM-1/STS-3c VPI (<=12 lsb bit) range: 0-4095
INT cktAtmVCI	1.3.6.1.4.1.277.1.6.1.1.74	INTEGER	read-write	VCI value in the ATM cell header: ATM DXI with HSSI IOP VCI (6 lsb bit) range: 0 - 63 ATM UNI DS3/E3 IOP VCI (8 lsb bit) range: 0 - 255 T1 ATM 4 lsb VCI (6 lsb bit) range 0 - 255 ATM-IWU STM-1/STS-3c VCI (<=12 lsb bit) range: 0-4095
INT cktType	1.3.6.1.4.1.277.1.6.1.1.75	INTEGER	read-only	1 if a permanent virtual circuit; 2 if a switched virtual circuit.
OCT cktSvcCallingParty	1.3.6.1.4.1.277.1.6.1.1.76	OCTET STRING	read-only	The calling party number if this is a switched virtual circuit.
OCT cktSvcCalledParty	1.3.6.1.4.1.277.1.6.1.1.77	OCTET STRING	read-only	The called party number if this is a switched virtual circuit.
TIK cktSvcDuration	1.3.6.1.4.1.277.1.6.1.1.78	TimeTicks	read-only	The duration since the SVC circuit has been running.
INT cktSvcCause	1.3.6.1.4.1.277.1.6.1.1.79	INTEGER	read-only	SVC cause number. The index will be 0.0 and should be disregarded. The following cause numbers maybe returned by stdx: 1 - unassigned number, callee is not assigned 2 - no route to specified transit network 3 - no route to destination 6 - channel unacceptable 16 - normal clearing 17 - user busy 18 - no user responding 21 - call rejected by whoever is sending this cause 22 - number changed, called party has changed its number 27 - destination out of order (the interface to called user) 28 - called party number is invalid 29 - facility requested can't be provided by network 30 - included in STATUS message to indicate it is responding to a STATUS ENQUIRY 31 - unspecified, used if no other cause is appropriate 34 - no circuit or channel available to handle the call 38 - network is out of order 41 - tempprary failure, i.e., caller may try again 42 - network congestion 43 - access information (user-to-user) discarded 44 - requested circuit unavailable 58 - bearer capability not available 63 - requested service unavailable 65 - requested bearer capability is not implemented 81 - call reference is unknown 95 - invalid message 96 - mandatory information element is missing 97 - message type is unknown 98 - message not compatible with call state 99 - information element is unknown or not implemented 100 - invalid information element contents 101 - message not compatible with call state
INT cktXlatFlag	1.3.6.1.4.1.277.1.6.1.1.80	INTEGER	read-write	0 if RFC1490 or no translation; 1 if RFC1483 translation.
INT cktDestLaddr	1.3.6.1.4.1.277.1.6.1.1.81	INTEGER	read-write	The destination logical address of the circuit.
INT cktSrcLaddr	1.3.6.1.4.1.277.1.6.1.1.82	INTEGER	read-write	The source logical address of the circuit.
INT cktLoop	1.3.6.1.4.1.277.1.6.1.1.83	INTEGER	read-write	Setting this variable controls the loopback status of the given circuit endpoint.
INT cktRerouteBalance	1.3.6.1.4.1.277.1.6.1.1.84	INTEGER	read-write	Setting this variable controls the use of rerouting to balance link usage.
INT cktCallingBackup	1.3.6.1.4.1.277.1.6.1.1.85	INTEGER	read-only	Indicates if a caller endpoint is calling a backup PVC.
INT cktRCir	1.3.6.1.4.1.277.1.6.1.1.86	INTEGER	read-write	The average number of user data (bits) that the network agrees to transfer over the circuit in the opposite direction, measured over the measurement interval T = cktBc/cktCir.
INT cktAtmQoS	1.3.6.1.4.1.277.1.6.1.1.87	INTEGER	read-write	The Quality of Service of the ATM Circuit. Valid only for ATM type circuits.
CTR cktAtmInCells	1.3.6.1.4.1.277.1.6.1.1.88	Counter	read-only	The Number of ATM cells received on a VC (VPC or VCC).
CTR cktAtmOutCells	1.3.6.1.4.1.277.1.6.1.1.89	Counter	read-only	The Number of ATM cells transmitted on a VC (VPC or VCC)..
CTR cktAtmInDiscardedClp0Cells	1.3.6.1.4.1.277.1.6.1.1.90	Counter	read-only	The Number of ATM CLP0 cells received and discarded on a VC (VPC or VCC)..
CTR cktAtmInDiscardedClp1Cells	1.3.6.1.4.1.277.1.6.1.1.91	Counter	read-only	The Number of ATM CLP1 cells received and discarded on a VC (VPC or VCC).
INT cktAtmVcType	1.3.6.1.4.1.277.1.6.1.1.92	INTEGER	read-write	Type of ATM connection (VPC or VCC).
INT cktAtmPCR	1.3.6.1.4.1.277.1.6.1.1.93	INTEGER	read-write	The Peak Cell Rate measured in cells/second at which cells are transmitted for this circuit.
INT cktAtmSCR	1.3.6.1.4.1.277.1.6.1.1.94	INTEGER	read-write	The Sustainable Cell Rate is the average transmission rate in cells per second for this circuit. It must be less than or or equal to the Peak Cell Rate.
INT cktAtmMBS	1.3.6.1.4.1.277.1.6.1.1.95	INTEGER	read-write	The Maximum Burst size determines the maximum number of cells that can be transmitted at the peak cell rate.
CTR cktAtmInPassedClp0Cells	1.3.6.1.4.1.277.1.6.1.1.96	Counter	read-only	The Number of ATM CLP 0 cells received and passed UPC on a VC (VPC or VCC).
CTR cktAtmInPassedClp1Cells	1.3.6.1.4.1.277.1.6.1.1.97	Counter	read-only	The Number of ATM CLP 1 cells received and passed UPC on a VC (VPC or VCC).
CTR cktAtmInTaggedCells	1.3.6.1.4.1.277.1.6.1.1.98	Counter	read-only	The Number of ATM cells received and tagged on a VC (VPC or VCC).
CTR cktAtmOutClp0Cells	1.3.6.1.4.1.277.1.6.1.1.99	Counter	read-only	The Number of ATM CLP 0 cells transmitted on a VC (VPC or VCC)..
CTR cktAtmOutClp1Cells	1.3.6.1.4.1.277.1.6.1.1.100	Counter	read-only	The Number of ATM CLP 1 cells transmitted on a VC (VPC or VCC)..
INT cktAtmRQoS	1.3.6.1.4.1.277.1.6.1.1.101	INTEGER	read-write	The Quality of Service of the ATM connection in the opposite direction.
INT cktAtmTfdType	1.3.6.1.4.1.277.1.6.1.1.102	INTEGER	read-write	The combination of traffic parameters.
INT cktAtmRTfdType	1.3.6.1.4.1.277.1.6.1.1.103	INTEGER	read-write	The combination of traffic parameters in opposite direction.
INT cktAtmTfdParam1	1.3.6.1.4.1.277.1.6.1.1.104	INTEGER	read-write	The traffic descriptor parameter 1.
INT cktAtmTfdParam2	1.3.6.1.4.1.277.1.6.1.1.105	INTEGER	read-write	The traffic descriptor parameter 2.
INT cktAtmTfdParam3	1.3.6.1.4.1.277.1.6.1.1.106	INTEGER	read-write	The traffic descriptor parameter 3.
INT cktAtmRTfdParam1	1.3.6.1.4.1.277.1.6.1.1.107	INTEGER	read-write	The traffic descriptor parameter 1 for opposite direction.
INT cktAtmRTfdParam2	1.3.6.1.4.1.277.1.6.1.1.108	INTEGER	read-write	The traffic descriptor parameter 3 for opposite direction.
INT cktAtmRTfdParam3	1.3.6.1.4.1.277.1.6.1.1.109	INTEGER	read-write	The traffic descriptor parameter 3 for opposite direction.
INT cktAtmFrameIWF	1.3.6.1.4.1.277.1.6.1.1.110	INTEGER	read-write	Frame Relay/ATM Interworking Function indicator.
INT cktAtmUserPlane	1.3.6.1.4.1.277.1.6.1.1.111	INTEGER	read-write	Bitmap defining user plane capabilities.
INT cktRBc	1.3.6.1.4.1.277.1.6.1.1.112	INTEGER	read-write	The maximum amount of data (bits) that the network agrees to transfer over the circuit in the opposite direction under normal conditions, during the measurement interval.
INT cktRBe	1.3.6.1.4.1.277.1.6.1.1.113	INTEGER	read-write	The maximum amount of uncommitted data (bits) that the network will attempt to transfer over the circuit in the opposite direction during the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ifSpeed.
INT cktOamLoopbackDirection	1.3.6.1.4.1.277.1.6.1.1.114	INTEGER	read-write	Which direction to send the loopback cell. If 'local', send out this circuit entry's port. If 'remote', send out the remote circuit entry's port.
INT cktOamLoopbackType	1.3.6.1.4.1.277.1.6.1.1.115	INTEGER	read-write	Type of oam loopback to send - either segment or end to end.
INT cktOamLoopbackHops	1.3.6.1.4.1.277.1.6.1.1.116	INTEGER	read-write	Number of hops the loopback cell should traverse inside the Cascade network before being echoed back by the far Cascade device.
INT cktOamLoopbackCount	1.3.6.1.4.1.277.1.6.1.1.117	INTEGER	read-write	Number of oam loopback cells left to send this session. Setting this from zero to non-zero starts the loopback session.
CTR cktOamLoopbackReceived	1.3.6.1.4.1.277.1.6.1.1.118	Counter	read-only	Number of oam responses received for this loopback session.
CTR cktOamLoopbackTimeouts	1.3.6.1.4.1.277.1.6.1.1.119	Counter	read-only	Number of times a loopback response was not received within the timeout period during this loopback session.
INT cktOamLoopbackReceivedHigh	1.3.6.1.4.1.277.1.6.1.1.120	INTEGER	read-only	Highest response time (in milliseconds) of an oam loopback response this loopback session.
INT cktOamLoopbackReceivedLow	1.3.6.1.4.1.277.1.6.1.1.121	INTEGER	read-only	Lowest response time (in milliseconds) of an oam loopback response this loopback session.
INT cktOamLoopbackReceivedAvg	1.3.6.1.4.1.277.1.6.1.1.122	INTEGER	read-only	Average response time (in milliseconds) of an oam loopback response this loopback session.
INT cktOamAlarmDisable	1.3.6.1.4.1.277.1.6.1.1.123	INTEGER	read-write	If disabled, then don't generate oam alarms if this circuit is down.
INT cktShaperId	1.3.6.1.4.1.277.1.6.1.1.124	INTEGER	read-write	The shaper to be used for this virtual connection interworking with frame relay: 1-port ATM-IWU STM-1/STS-3c card -------------------------------- Values: 1..16
INT cktOspfCtd	1.3.6.1.4.1.277.1.6.1.1.125	INTEGER	read-write	The allowed cell delay: 4-port CBR E1/DS1 card ---------------------- The maximum allowed cell delay in msec
INT cktOspfCdv	1.3.6.1.4.1.277.1.6.1.1.126	INTEGER	read-write	The allowed cell delay variation: 4-port CBR E1/DS1 card ---------------------- The maximum allowed cell delay variation in msec
INT cktOutPort	1.3.6.1.4.1.277.1.6.1.1.127	INTEGER	read-only	The outgoing port number for the adjacent VC entry in this switch.
INT cktOutVc	1.3.6.1.4.1.277.1.6.1.1.128	INTEGER	read-only	The adjacent VC entry corresponding to this circuit accross the bus.
INT cktRVc	1.3.6.1.4.1.277.1.6.1.1.129	INTEGER	read-only	The adjacent VC entry corresponding to this circuit accross the trunk.
INT cktEntryType	1.3.6.1.4.1.277.1.6.1.1.130	INTEGER	read-only	The internal type of circuit entry allocated by the circuit manager.
OCT cktDiagStr	1.3.6.1.4.1.277.1.6.1.1.131	OCTET STRING	read-only	Internal diagnostic information.
INT cktSvcAalType	1.3.6.1.4.1.277.1.6.1.1.132	INTEGER	read-only	The AAL type for this SVC.
INT cktSvcBBearerClass	1.3.6.1.4.1.277.1.6.1.1.133	INTEGER	read-only	The Broadband bearer capability class for this SVC.
INT cktSvcBBearerClippingSusc	1.3.6.1.4.1.277.1.6.1.1.134	INTEGER	read-only	The Broadband bearer capability clipping susceptibility for this SVC.
INT cktSvcBBearerTmgReq	1.3.6.1.4.1.277.1.6.1.1.135	INTEGER	read-only	The Broadband bearer capability timing requirements for this SVC.
INT cktSvcBBearerTfcType	1.3.6.1.4.1.277.1.6.1.1.136	INTEGER	read-only	The Broadband bearer capability traffic type for this SVC.
INT cktAtmUPCEnable	1.3.6.1.4.1.277.1.6.1.1.137	INTEGER	read-write	Enable ATM UPC Function.
INT cktRPriority	1.3.6.1.4.1.277.1.6.1.1.138	INTEGER	read-write	The priority level (0 through 3) for this circuit in the opposite direction. When port service type is defined as 'mono-class', this priority means the forward priority of the circuit. When port service type is defined as 'multi-class', this priority means the discard priority of the circuit.
INT cktRtPriority	1.3.6.1.4.1.277.1.6.1.1.139	INTEGER	read-write	The routing priority level of the circuit which is a 8 bit number where the 3-bit bumping priority is contained in bits 0-2 and the 4-bit bandwidth priority is contained in bits 3-6. For ATM multipoint ckts, bw and bumping priorities should be zero.
INT cktDeltaBc	1.3.6.1.4.1.277.1.6.1.1.140	INTEGER	read-write	The maximum number of bits that the network agree to transfer over the circuit as committed bits during the measurement interval under the CONDITION that the circuit still has POSITIVE committed bit (Bc) credits before receiving a frame but will have NEGATIVE Bc credits after accepting the frame. The range of this variable is 0 to 65,528 bits. By default, if not configured when creating the entry, it is set to 65,528 bits.
INT cktDeltaBe	1.3.6.1.4.1.277.1.6.1.1.141	INTEGER	read-write	The maximum number of bits that the network agree to transfer over the circuit as allowed excess bits during the measurement interval under the CONDITION that the circuit still has POSITIVE excess bit (Be) credits before receiving a frame but will have NEGATIVE Be credits after accepting the frame. The range of this variable is 0 to 65,528 bits. By default, if not configured when creating the entry, it is set to 65,528 bits.
INT cktDeltaRBc	1.3.6.1.4.1.277.1.6.1.1.142	INTEGER	read-write	The maximum number of bits that the network agree to transfer over the circuit as committed bits in the opposite direction during the measurement interval under the CONDITION that the circuit still has POSITIVE committed bit (Bc) credits before receiving a frame but will have NEGATIVE Bc credits after accepting the frame. The range of this variable is 0 to 65,528 bits. By default, if not configured when creating the entry, it is set to 65,528 bits.
INT cktDeltaRBe	1.3.6.1.4.1.277.1.6.1.1.143	INTEGER	read-write	The maximum number of bits that the network agree to transfer over the circuit as allowed excess bits in the opposite direction during the measurement interval under the CONDITION that the circuit still has POSITIVE excess bit (Be) credits before receiving a frame but will have NEGATIVE Be credits after accepting the frame. The range of this variable is 0 to 65,528 bits. By default, if not configured when creating the entry, it is set to 65,528 bits.
INT cktRedFrPcnt	1.3.6.1.4.1.277.1.6.1.1.144	INTEGER	read-write	The percentage of RED frame bits that are allowed to enter the network, during the measurement interval, under non-congestion condition. Its value range is 0 - 100 and default value is 100. Its calculation is as follows: cktRedFrPcn = (allowed RED frame bits)/(Bc+Be+allowed RED frame bits)
INT cktRedFrRPcnt	1.3.6.1.4.1.277.1.6.1.1.145	INTEGER	read-write	The percentage of RED frame bits that are allowed to enter the network in the opposite direction, during the measurement interval, under non-congestion condition. Its value range is 0 - 100 and default value is 100. Its calculation is as follows: cktRedFrRPcn = (allowed RED frame bits)/(rBc+rBe+allowed RED frame bits)
INT cktRateEnforceSchm	1.3.6.1.4.1.277.1.6.1.1.146	INTEGER	read-write	Variable used to indicate the rate enforcement scheme employed. 0: Slide window rate enforcement scheme 1: Jump window rate enforcement scheme 2: Simple rate enforcement scheme Default value is 2.
INT cktRateEnforceRSchm	1.3.6.1.4.1.277.1.6.1.1.147	INTEGER	read-write	Variable used to indicate the rate enforcement scheme employed in the opposite direction. 0: Slide window rate enforcement scheme 1: Jump window rate enforcement scheme 2: Simple rate enforcement scheme Default value is 2.
INT cktROde	1.3.6.1.4.1.277.1.6.1.1.148	INTEGER	read-write	This variable states whether graceful discard is enabled for the ckt in the opposite direction.
INT cktPrivateNet	1.3.6.1.4.1.277.1.6.1.1.149	INTEGER	read-write	If non-zero, indicates the private network that the circuit belongs to. If 0, the circuit has access to the entire public portion of the network.
INT cktPrivateNetOverflow	1.3.6.1.4.1.277.1.6.1.1.150	INTEGER	read-write	Indicates how private network circuits are handled, when the resources of the network have become exhausted. If set to use-public, the resources of the public network can be used during overflow conditions.
INT cktCustomerID	1.3.6.1.4.1.277.1.6.1.1.151	INTEGER	read-write	The Customer that owns this circuit. For Virtual Private Networking Support.
INT cktAtmCDVT	1.3.6.1.4.1.277.1.6.1.1.152	INTEGER	read-write	The Cell Delay Variation Tolerance for the VC
INT cktNdcEnable	1.3.6.1.4.1.277.1.6.1.1.153	INTEGER	read-write	Enable/disable Network Data Collection for a PVC on an IOM. The number of NDC-monitored PVCs is limited as follows: 30 per DS3 interface, 90 per OC3 interface, and 360 per OC12 interface.
INT cktInterworkingFrToAtmCLP	1.3.6.1.4.1.277.1.6.1.1.154	INTEGER	read-write	CLP mapping for Frame Relay To ATM Service Interworking.
INT cktInterworkingFrToAtmDe	1.3.6.1.4.1.277.1.6.1.1.155	INTEGER	read-write	DE bit mapping for ATM To Frame Relay Service Interworking.
INT cktNrtsCLP1	1.3.6.1.4.1.277.1.6.1.1.156	INTEGER	read-write	Whether to use the discard threshold as the CLP1 Discard threshold upon reception of a cell by the NRTS processor in the forward direction.
CTR cktNrtsDiscardClp0	1.3.6.1.4.1.277.1.6.1.1.157	Counter	read-only	The number of the CLP0 cells received and discarded by the NRTS processor.
CTR cktNrtsDiscardClp1	1.3.6.1.4.1.277.1.6.1.1.158	Counter	read-only	The number of the CLP1 cells received and discarded by the NRTS processor.
INT cktMPEnableAMF	1.3.6.1.4.1.277.1.6.1.1.159	INTEGER	read-write	Whether the Multilink PPP PVC Attributes Modification Feature is enabled.
INT cktMPEligible	1.3.6.1.4.1.277.1.6.1.1.160	INTEGER	read-write	Whether this circuit is eligible to be a member of a Multilink PPP bundle.
INT cktMPForcedCaller	1.3.6.1.4.1.277.1.6.1.1.161	INTEGER	read-write	Whether this end of the circuit has been forced to be caller to support Multilink PPP PVC Attributes Modification Feature.
INT cktMPForcedCallee	1.3.6.1.4.1.277.1.6.1.1.162	INTEGER	read-write	Whether this end of the circuit has been forced to be callee to support Multilink PPP PVC Attributes Modification Feature.
INT cktFrameSize	1.3.6.1.4.1.277.1.6.1.1.163	INTEGER	read-write	The average frame size (measured in number of bytes) of the traffic on the circuit. If not configured, it is set to 280 (bytes) by default.
INT cktRFrameSize	1.3.6.1.4.1.277.1.6.1.1.164	INTEGER	read-write	The average frame size (measured in number of bytes) of the traffic on the circuit on the reverse direction. If not configured, it is set to 280 (bytes) by default.
INT cktRNrtsCLP1	1.3.6.1.4.1.277.1.6.1.1.165	INTEGER	read-write	Whether to use the discard threshold as the CLP1 Discard threshold upon reception of a cell by the NRTS processor in the reverse direction.
INT cktBBearerAtmTransferCapability	1.3.6.1.4.1.277.1.6.1.1.166	INTEGER	read-only	The broadband bearer ATM transfer capability of this SVC. This object is not pertinent to IISP 3.x, UNI 3.x or Q.2931 signaling.
INT cktAtmFrameDiscard	1.3.6.1.4.1.277.1.6.1.1.167	INTEGER	read-write	The ATM frame discard state for this circuit.
INT cktRAtmFrameDiscard	1.3.6.1.4.1.277.1.6.1.1.168	INTEGER	read-write	The reverse ATM frame discard state for this circuit.
INT cktAbrFRMRTT	1.3.6.1.4.1.277.1.6.1.1.169	INTEGER	read-only	The ABR fixed RM round trip time for this SVC.
INT cktAbrICR	1.3.6.1.4.1.277.1.6.1.1.170	INTEGER	read-only	The ABR initial cell rate for this SVC.
INT cktRAbrICR	1.3.6.1.4.1.277.1.6.1.1.171	INTEGER	read-only	The reverse ABR initial cell rate for this SVC.
INT cktAbrRIF	1.3.6.1.4.1.277.1.6.1.1.172	INTEGER	read-only	The ABR rate increase factor for this SVC.
INT cktRAbrRIF	1.3.6.1.4.1.277.1.6.1.1.173	INTEGER	read-only	The reverse ABR rate increase factor for this SVC.
INT cktAbrRDF	1.3.6.1.4.1.277.1.6.1.1.174	INTEGER	read-only	The ABR rate decrease factor for this SVC.
INT cktRAbrRDF	1.3.6.1.4.1.277.1.6.1.1.175	INTEGER	read-only	The reverse ABR rate decrease factor for this SVC.
INT cktAbrTBE	1.3.6.1.4.1.277.1.6.1.1.176	INTEGER	read-only	The ABR transient buffer exposure for this SVC.
INT cktRAbrTBE	1.3.6.1.4.1.277.1.6.1.1.177	INTEGER	read-only	The reverse ABR transient buffer exposure for this SVC.
INT cktAbrNRM	1.3.6.1.4.1.277.1.6.1.1.178	INTEGER	read-only	The ABR NRM for this SVC.
INT cktRAbrNRM	1.3.6.1.4.1.277.1.6.1.1.179	INTEGER	read-only	The reverse ABR NRM for this SVC.
INT cktAbrTRM	1.3.6.1.4.1.277.1.6.1.1.180	INTEGER	read-only	The ABR TRM for this SVC.
INT cktRAbrTRM	1.3.6.1.4.1.277.1.6.1.1.181	INTEGER	read-only	The reverse ABR TRM for this SVC.
INT cktAbrCDF	1.3.6.1.4.1.277.1.6.1.1.182	INTEGER	read-only	The ABR CDF for this SVC.
INT cktRAbrCDF	1.3.6.1.4.1.277.1.6.1.1.183	INTEGER	read-only	The reverse ABR CDF for this SVC.
INT cktAbrADTF	1.3.6.1.4.1.277.1.6.1.1.184	INTEGER	read-only	The ABR ADTF for this SVC.
INT cktRAbrADTF	1.3.6.1.4.1.277.1.6.1.1.185	INTEGER	read-only	The reverse ABR ADTF for this SVC.
INT cktAccumCTD	1.3.6.1.4.1.277.1.6.1.1.186	INTEGER	read-only	The accumulated cell(frame) transfer delay for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid.
INT cktAccumCDV	1.3.6.1.4.1.277.1.6.1.1.187	INTEGER	read-only	The accumulated cell delay variation for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid.
INT cktAccumRCDV	1.3.6.1.4.1.277.1.6.1.1.188	INTEGER	read-only	The accumulated reverse cell delay variation for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid.
INT cktCLR	1.3.6.1.4.1.277.1.6.1.1.189	INTEGER	read-write	The cell loss ratio requirement, expressed as a negative exponent of 10. The default value 255 represents any cell loss ratio acceptable.
INT cktRCLR	1.3.6.1.4.1.277.1.6.1.1.190	INTEGER	read-write	The reverse cell loss ratio requirement, expressed as a negative exponent of 10. The default value 255 represents any cell loss ratio acceptable.
INT cktAtmLijId	1.3.6.1.4.1.277.1.6.1.1.191	INTEGER	read-only	The Leaf Initiated Join ID of the PMP SVC rooted at this interface.
INT cktAtmLijType	1.3.6.1.4.1.277.1.6.1.1.192	INTEGER	read-only	The Leaf Initiated Join type of the PMP SVC rooted at this interface.
INT cktRtLastDelay	1.3.6.1.4.1.277.1.6.1.1.193	INTEGER	read-only	The last round-trip delay (micro-seconds).
INT cktRtAccuMinDelay	1.3.6.1.4.1.277.1.6.1.1.194	INTEGER	read-only	The prev min round-trip delay (micro-seconds).
INT cktRtAccuMaxDelay	1.3.6.1.4.1.277.1.6.1.1.195	INTEGER	read-only	The prev max round-trip delay (micro-seconds).
INT cktRtAccuAvgDelay	1.3.6.1.4.1.277.1.6.1.1.196	INTEGER	read-only	The prev avg round-trip delay (micro-seconds).
INT cktQosIntPeriod	1.3.6.1.4.1.277.1.6.1.1.197	INTEGER	read-write	The number of periods for calculating qos params.
CTR cktAtmOutOAMClp0Cells	1.3.6.1.4.1.277.1.6.1.1.198	Counter	read-only	The number of OAM CLP0 cells transmitted on this circuit. For BIO1 card (on Garnet Platform), this count is not reported separately - see cktEntry 99.
CTR cktAtmOutOAMClp1Cells	1.3.6.1.4.1.277.1.6.1.1.199	Counter	read-only	The number of OAM CLP1 cells transmitted on this circuit. For BIO1 card (on Garnet Platform), this count is not reported separately - see cktEntry 100.
INT cktReqCTD	1.3.6.1.4.1.277.1.6.1.1.200	INTEGER	read-write	The requested cell/frame delay variation for this circuit, in microseconds. The range for PVC is 1 - 0x00FFFFFF. The default is 0x00FFFFFF, which means not valid.
CTR cktInOctetsPeak	1.3.6.1.4.1.277.1.6.1.1.201	Counter	read-only	The 5-minute peak value of the number of inbound octets (bytes) for the circuit - from Bulk Statistics.
CTR cktOutOctetsPeak	1.3.6.1.4.1.277.1.6.1.1.202	Counter	read-only	The 5-minute peak value of the number of outbound octets (bytes) for the circuit - from Bulk Statistics.
CTR cktInDEOctetsPeak	1.3.6.1.4.1.277.1.6.1.1.203	Counter	read-only	The 5-minute peak value of the number of inbound DE-marked octets (bytes) for the circuit - from Bulk Statistics.
CTR cktOutDEOctetsPeak	1.3.6.1.4.1.277.1.6.1.1.204	Counter	read-only	The 5-minute peak value of the number of outbound DE-marked octets (bytes) for the circuit - from Bulk Statistics.
CTR cktInODEOctetsPeak	1.3.6.1.4.1.277.1.6.1.1.205	Counter	read-only	The 5-minute peak value of the number of inbound ODE-marked octets (bytes) for the circuit - from Bulk Statistics.
CTR cktOutODEOctetsPeak	1.3.6.1.4.1.277.1.6.1.1.206	Counter	read-only	The 5-minute peak value of the number of outbound ODE-marked octets (bytes) for the circuit - from Bulk Statistics.
INT cktAdminCostThreshold	1.3.6.1.4.1.277.1.6.1.1.207	INTEGER	read-write	Maximum allowable admin cost for the circuit. If no paths are available with cost less than or equal to this value, the circuit is not established. DEFVAL is 0 which means invalid, valid values range from 1 to 0xFFFFFFFF.
INT cktAtmSvcServiceCategory	1.3.6.1.4.1.277.1.6.1.1.208	INTEGER	read-only	The derived service category in the forward direction for this ATM SVC.
INT cktAtmSvcRServiceCategory	1.3.6.1.4.1.277.1.6.1.1.209	INTEGER	read-only	The derived service category in the reverse direction for this ATM SVC.
INT cktInterworkingFrToAtmEFCI	1.3.6.1.4.1.277.1.6.1.1.210	INTEGER	read-write	EFCI mapping for Frame Relay To ATM Service Interworking.
INT cktDiagSARMon	1.3.6.1.4.1.277.1.6.1.1.211	INTEGER	read-write	Used to start or stop flow on the inbound/outbound ATMizer without informing the PPC.
INT cktAdminCostReal	1.3.6.1.4.1.277.1.6.1.1.212	INTEGER	read-only	Actual value of total administration cost of a circuit. Ranges from 0 to 0xFFFFFFFF.
CTR cktAtmInClp0Cells	1.3.6.1.4.1.277.1.6.1.1.213	Counter	read-only	The Number of ATM CLP 0 cells received on a VC (VPC or VCC).
CTR cktAtmInClp1Cells	1.3.6.1.4.1.277.1.6.1.1.214	Counter	read-only	The Number of ATM CLP 1 cells received on a VC (VPC or VCC).
CTR cktATMAAL5CRC32Error	1.3.6.1.4.1.277.1.6.1.1.215	Counter	read-only	Number of received AAL5 packets with CRC32 errors.
CTR cktATMAAL5CPIError	1.3.6.1.4.1.277.1.6.1.1.216	Counter	read-only	Number of received AAL5 packets with CPI errors The only valid value currently defined for the CPI field is all zeros
CTR cktATMAAL5LengthError	1.3.6.1.4.1.277.1.6.1.1.217	Counter	read-only	Number of received AAL5 packets which satisfied one of the following error conditions: 1. number of received cells * 48 bytes - length value in trailer > 55 bytes 2. number of received cells * 48 bytes - length value in trailer < 8 bytes
CTR cktATMAAL5ReassemblyTimerError	1.3.6.1.4.1.277.1.6.1.1.218	Counter	read-only	Number of expired reassembly timers
CTR cktATMAAL5MaxNrSegError	1.3.6.1.4.1.277.1.6.1.1.219	Counter	read-only	Number of received AAL5 packets which exceeds the maximum allowed length
CTR cktIWF1490to1483Error	1.3.6.1.4.1.277.1.6.1.1.220	Counter	read-only	Number of Frames received that failed the rfc1490 to rfc 1483 header translation. This error counter indicates that frames being recevied from the frame relay side of the connection have an incorrectly formatted 1490 header and cannot be translated. See cktIWF1490to1483LastBadHeader for the last received 1490 header
STR cktIWF1490to1483LastBadHeader	1.3.6.1.4.1.277.1.6.1.1.221	DisplayString	read-only	Ascii string of the first 8 bytes of the header from the last frame discarded because the 1490 to 1483 header translation failed. The string displays the hexidecimal values for the data bytes
CTR cktIWF1483to1490Error	1.3.6.1.4.1.277.1.6.1.1.222	Counter	read-only	Number of Frames received that failed the rfc1483 to rfc 1490 header translation. This error counter indicates that frames being recevied from the atm side of the connection have an incorrectly formatted 1483 header and cannot be translated. See cktIWF1483to1490LastBadHeader for the last received 1490 header
STR cktIWF1483to1490LastBadHeader	1.3.6.1.4.1.277.1.6.1.1.223	DisplayString	read-only	Ascii string of the first 10 bytes of the header from the last frame discarded because the 1483 to 1490 header translation failed. The string displays the hexidecimal values for the data bytes
cktLeafTable	1.3.6.1.4.1.277.1.6.2		not-accessible	A table containing information about leaves of multipoint circuits.
cktLeafEntry	1.3.6.1.4.1.277.1.6.2.1		not-accessible	The objects relevant to a single leaf in a multipoint circuit.
IND cktLeafSrcIfIndex	1.3.6.1.4.1.277.1.6.2.1.1	Index	read-only	The interface ID at this node's ingress port for the corresponding multipoint circuit.
INT cktLeafSrcDlci	1.3.6.1.4.1.277.1.6.2.1.2	INTEGER	read-only	The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's ingress port for the corresponding multipoint circuit.
INT cktLeafEndpointIndex	1.3.6.1.4.1.277.1.6.2.1.3	INTEGER	read-only	An identifier unique to this leaf for the corresponding multipoint circuit.
TIK cktLeafCreationTime	1.3.6.1.4.1.277.1.6.2.1.4	TimeTicks	read-only	The value of sysUpTime when this leaf was created for the corresponding multipoint circuit.
IND cktLeafEgressIfIndex	1.3.6.1.4.1.277.1.6.2.1.5	Index	read-only	The interface ID at this node's egress port for this leaf's segment of the corresponding multipoint circuit.
INT cktLeafEgressDlci	1.3.6.1.4.1.277.1.6.2.1.6	INTEGER	read-only	The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's egress port for this leaf's segment of the corresponding multipoint circuit.
INT cktLeafDestNodeId	1.3.6.1.4.1.277.1.6.2.1.7	INTEGER	read-write	The node ID of the node where this leaf terminates.
IND cktLeafDestIfIndex	1.3.6.1.4.1.277.1.6.2.1.8	Index	read-write	The interface ID at the egress port of the destination node for this leaf, if this is a PVC.
INT cktLeafDestDlci	1.3.6.1.4.1.277.1.6.2.1.9	INTEGER	read-only	The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's destination port for the corresponding multipoint circuit.
OCT cktLeafSvcCallingParty	1.3.6.1.4.1.277.1.6.2.1.10	OCTET STRING	read-only	The calling party number for this leaf, if this is an SVC.
OCT cktLeafSvcCalledParty	1.3.6.1.4.1.277.1.6.2.1.11	OCTET STRING	read-only	The called party number for this leaf, if this is an SVC.
INT cktLeafAdminStatus	1.3.6.1.4.1.277.1.6.2.1.12	INTEGER	read-write	The desired state for the leaf entry.
INT cktLeafVcState	1.3.6.1.4.1.277.1.6.2.1.13	INTEGER	read-only	The current state of the leaf PVC segment in the Cascade network.
INT cktLeafOperStatus	1.3.6.1.4.1.277.1.6.2.1.14	INTEGER	read-only	The current operational status of the entire leaf PVC.
INT cktLeafDceState	1.3.6.1.4.1.277.1.6.2.1.15	INTEGER	read-only	The DCE state of the circuit.
INT cktLeafDteStatus	1.3.6.1.4.1.277.1.6.2.1.16	INTEGER	read-only	The DTE status of the circuit.
INT cktLeafDteState	1.3.6.1.4.1.277.1.6.2.1.17	INTEGER	read-only	The DTE state of the circuit.
OCT cktLeafVcPtr	1.3.6.1.4.1.277.1.6.2.1.18	OCTET STRING	read-only	An 8-byte Octect string indicating the vc pointer.
INT cktLeafHopCnt	1.3.6.1.4.1.277.1.6.2.1.19	INTEGER	read-only	The count of hops along the circuit path. (Max is 16)
OCT cktLeafPath	1.3.6.1.4.1.277.1.6.2.1.20	OCTET STRING	read-only	The circuit path consisting a sequence of outbound interface indexes at nodes along the established circuit. The format is interface:interface:interface......
INT cktLeafFailReason	1.3.6.1.4.1.277.1.6.2.1.21	INTEGER	read-only	The reason for the PVC establishment failure.
INT cktLeafFailNode	1.3.6.1.4.1.277.1.6.2.1.22	INTEGER	read-only	The node which causes the PVC failure.
INT cktLeafFailPort	1.3.6.1.4.1.277.1.6.2.1.23	INTEGER	read-only	The port on the fail node which causes the PVC failure.
INT cktLeafHelloCounter	1.3.6.1.4.1.277.1.6.2.1.24	INTEGER	read-only	Number of PVC hello pdu frames received in the VC entry of the called side.
INT cktLeafHelloAckCounter	1.3.6.1.4.1.277.1.6.2.1.25	INTEGER	read-only	Number of PVC hello Ack pdu frames received in the VC entry of the calling side.
INT cktLeafAtmVPI	1.3.6.1.4.1.277.1.6.2.1.26	INTEGER	read-write	VPI value in the ATM cell header
INT cktLeafAtmVCI	1.3.6.1.4.1.277.1.6.2.1.27	INTEGER	read-write	VCI value in the ATM cell header
INT cktLeafType	1.3.6.1.4.1.277.1.6.2.1.28	INTEGER	read-only	1 if a permanent virtual circuit; 2 if a switched virtual circuit.
CTR cktLeafAtmInCells	1.3.6.1.4.1.277.1.6.2.1.29	Counter	read-only	The Number of ATM cells received on a VCC.
CTR cktLeafAtmOutCells	1.3.6.1.4.1.277.1.6.2.1.30	Counter	read-only	The Number of ATM cells transmitted on a VCC.
CTR cktLeafAtmInDiscardedClp0Cells	1.3.6.1.4.1.277.1.6.2.1.31	Counter	read-only	The Number of ATM CLP0 cells received and discarded on a VCC.
CTR cktLeafAtmInDiscardedClp1Cells	1.3.6.1.4.1.277.1.6.2.1.32	Counter	read-only	The Number of ATM CLP1 cells received and discarded on a VCC.
CTR cktLeafAtmInPassedClp0Cells	1.3.6.1.4.1.277.1.6.2.1.33	Counter	read-only	The Number of ATM CLP 0 cells received and passed UPC on a VCC.
CTR cktLeafAtmInPassedClp1Cells	1.3.6.1.4.1.277.1.6.2.1.34	Counter	read-only	The Number of ATM CLP 1 cells received and passed UPC on a VCC.
CTR cktLeafAtmInTaggedCells	1.3.6.1.4.1.277.1.6.2.1.35	Counter	read-only	The Number of ATM cells received and tagged on a VCC.
CTR cktLeafAtmOutClp0Cells	1.3.6.1.4.1.277.1.6.2.1.36	Counter	read-only	The Number of ATM CLP 0 cells transmitted on a VCC.
CTR cktLeafAtmOutClp1Cells	1.3.6.1.4.1.277.1.6.2.1.37	Counter	read-only	The Number of ATM CLP 1 cells transmitted on a VCC.
cktSmdsRtTable	1.3.6.1.4.1.277.1.6.3		not-accessible	A table containing information about destination, VC, hops and routes.
cktSmdsRtEntry	1.3.6.1.4.1.277.1.6.3.1		not-accessible	The information regarding routes from a node to all its neighbors.
INT cktSmdsRemoteNode	1.3.6.1.4.1.277.1.6.3.1.1	INTEGER	read-only	The nodeId of the node to which a rought is sought.
INT cktSmdsHopCnt	1.3.6.1.4.1.277.1.6.3.1.2	INTEGER	read-only	The number of hops to reach the desired destination node.
OCT cktSmdsRoute	1.3.6.1.4.1.277.1.6.3.1.3	OCTET STRING	read-only	The out-going Interface Id of each of the nodes in the path.
INT cktSmdsLocalPort	1.3.6.1.4.1.277.1.6.3.1.4	INTEGER	read-only	The out-going local portId.
INT cktSmdsRemotePort	1.3.6.1.4.1.277.1.6.3.1.5	INTEGER	read-only	The remote portId of the destination nodeId.
INT cktSmdsVcState	1.3.6.1.4.1.277.1.6.3.1.6	INTEGER	read-only	The state of the circuit.
card	1.3.6.1.4.1.277.1.7
INT cardNumber	1.3.6.1.4.1.277.1.7.1	INTEGER	read-only	The number of manageable cards physically present in this node. Standby cards are not considered manageable.
cardTable	1.3.6.1.4.1.277.1.7.2		not-accessible	A list of cardEntry's. The number of entries is given by the value of cardNumber
cardEntry	1.3.6.1.4.1.277.1.7.2.1		not-accessible	The card entry contains objects relevant to managing intelligent cards.
INT cardLogicalSlotId	1.3.6.1.4.1.277.1.7.2.1.1	INTEGER	read-only	The logical slot number of this card. This is used as an index for the cardTable. In redundant configurations, this can be the physical slot number of either redundant card. In non redundant configurations, this is the same as cardPhysicalSlotId.
INT cardPhysicalSlotId	1.3.6.1.4.1.277.1.7.2.1.2	INTEGER	read-only	The physical slot number of this card. This can be different from cardLogicalSlotId in redundant configurations.
CAR cardAdminType	1.3.6.1.4.1.277.1.7.2.1.3	CardTypes	read-write	The desired card type.
CAR cardOperType	1.3.6.1.4.1.277.1.7.2.1.4	CardTypes	read-only	The actual card type.
INT cardState	1.3.6.1.4.1.277.1.7.2.1.5	INTEGER	read-only	The state of this card.
CAR cardAdminStatus	1.3.6.1.4.1.277.1.7.2.1.6	CardStatuses	read-write	The desired status of this card.
CAR cardOperStatus	1.3.6.1.4.1.277.1.7.2.1.7	CardStatuses	read-only	The current status of this card.
INT cardDiagStatus	1.3.6.1.4.1.277.1.7.2.1.8	INTEGER	read-only	The current diagnostics status of this card, as determined by background diagnostics.
INT cardRedundConfig	1.3.6.1.4.1.277.1.7.2.1.9	INTEGER	read-only	Is the card configured for redundancy?
INT cardRedundSlotMask	1.3.6.1.4.1.277.1.7.2.1.10	INTEGER	read-write	A 32-bit mask indicating the slot position of this card and its redundant partner. The low bit is slot 1 and the high bit is slot 32.
INT cardRedundActual	1.3.6.1.4.1.277.1.7.2.1.11	INTEGER	read-only	Is the card currently connected to a redundant card?
INT cardRedundState	1.3.6.1.4.1.277.1.7.2.1.12	INTEGER	read-only	The current redundancy state of this card. Exception: when used as an index for the following objects: cardAdminType, cardAdminCapability, and cardAdminStatus, the value 1 indicates the card of the redundant pair in the lower-numbered slot, and the value 2 indicates the card in the higher-numbered slot.
TIK cardToRedundant	1.3.6.1.4.1.277.1.7.2.1.13	TimeTicks	read-write	Instructs the standby card to reset the active card and take over as new active card. The reset takes place after specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled request.
INT cardDiagNonFatalSource	1.3.6.1.4.1.277.1.7.2.1.14	INTEGER	read-only	Source who reported last non-fatal error.
TIK cardDiagNonFatalTime	1.3.6.1.4.1.277.1.7.2.1.15	TimeTicks	read-only	Time the last non-fatal error was reported.
INT cardDiagNonFatalErrMajor	1.3.6.1.4.1.277.1.7.2.1.16	INTEGER	read-only	Major error code of last non-fatal error.
INT cardDiagNonFatalErrMinor	1.3.6.1.4.1.277.1.7.2.1.17	INTEGER	read-only	Minor error code of last non-fatal error.
STR cardDiagNonFatalStr	1.3.6.1.4.1.277.1.7.2.1.18	DisplayString	read-only	Ascii string describing last non-fatal error.
INT cardDiagFatalSource	1.3.6.1.4.1.277.1.7.2.1.19	INTEGER	read-only	Source who reported last fatal error.
TIK cardDiagFatalTime	1.3.6.1.4.1.277.1.7.2.1.20	TimeTicks	read-only	Time the last fatal error was reported.
INT cardDiagFatalErrMajor	1.3.6.1.4.1.277.1.7.2.1.21	INTEGER	read-only	Major error code of last fatal error.
INT cardDiagFatalErrMinor	1.3.6.1.4.1.277.1.7.2.1.22	INTEGER	read-only	Minor error code of last fatal error.
STR cardDiagFatalStr	1.3.6.1.4.1.277.1.7.2.1.23	DisplayString	read-only	Ascii string describing last fatal error.
CTR cardDiagFatalReboots	1.3.6.1.4.1.277.1.7.2.1.24	Counter	read-only	Number of times the switch has re-booted since last fatal error was reported.
INT cardDiagFatalAddress	1.3.6.1.4.1.277.1.7.2.1.25	INTEGER	read-only	Address switch was executing when it encountered fatal error.
CTR cardDiagBackgroundPasses	1.3.6.1.4.1.277.1.7.2.1.26	Counter	read-only	Number of passes made by the background diagnostics.
CTR cardDiagBackgroundFailures	1.3.6.1.4.1.277.1.7.2.1.27	Counter	read-only	Number of failures discovered by background diagnostics.
CTR cardDiagBackgroundSuccesses	1.3.6.1.4.1.277.1.7.2.1.28	Counter	read-only	Number of successful passes by background diagnostics.
INT cardDiagLEDReset	1.3.6.1.4.1.277.1.7.2.1.29	INTEGER	read-write	Change the card state from marginal to active. Change the LED from yellow to green.
INT cardDiagPowerExtensive	1.3.6.1.4.1.277.1.7.2.1.30	INTEGER	read-write	Should power on diagnostics do slower, extensive testing, or fast testing?
GAU cardCpuUtil	1.3.6.1.4.1.277.1.7.2.1.31	Gauge	read-only	The CPU utilization percentage for packet processing on this intelligent card.
GAU cardMemoryUsage	1.3.6.1.4.1.277.1.7.2.1.32	Gauge	read-only	The memory utilization, in terms of free bytes, for this intelligent card.
GAU cardMaxVCs	1.3.6.1.4.1.277.1.7.2.1.33	Gauge	read-only	The number of available VC entries on this card.
GAU cardInUseVCs	1.3.6.1.4.1.277.1.7.2.1.34	Gauge	read-only	The number of currently in use VC entries on this card.
GAU cardFreeVCs	1.3.6.1.4.1.277.1.7.2.1.35	Gauge	read-only	The number of currently free VC entries on this card.
CTR cardInOctets	1.3.6.1.4.1.277.1.7.2.1.36	Counter	read-only	The total number of octets received on this card, including framing bytes.
CTR cardInPkts	1.3.6.1.4.1.277.1.7.2.1.37	Counter	read-only	The total number of packets received on this card.
CTR cardOutOctets	1.3.6.1.4.1.277.1.7.2.1.38	Counter	read-only	The total number of octets transmitted out of this card, including framing bytes.
CTR cardOutPkts	1.3.6.1.4.1.277.1.7.2.1.39	Counter	read-only	The total number of packets requested to be transmitted out of this card, including those that were discarded or not sent.
TIK cardToWarmboot	1.3.6.1.4.1.277.1.7.2.1.40	TimeTicks	read-write	Warm boots the card after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request.
TIK cardToColdboot	1.3.6.1.4.1.277.1.7.2.1.41	TimeTicks	read-write	Cold boots the card after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request.
STR cardModel	1.3.6.1.4.1.277.1.7.2.1.42	DisplayString	read-only	The part number of the card.
STR cardSerial	1.3.6.1.4.1.277.1.7.2.1.43	DisplayString	read-only	The serial number of the card.
STR cardSwRev	1.3.6.1.4.1.277.1.7.2.1.44	DisplayString	read-only	The software rev number (major.minor).
STR cardHwRev	1.3.6.1.4.1.277.1.7.2.1.45	DisplayString	read-only	The hardware rev number (major.minor).
STR cardEpromRev	1.3.6.1.4.1.277.1.7.2.1.46	DisplayString	read-only	The EPROM firmware rev number (major.minor).
STR cardName	1.3.6.1.4.1.277.1.7.2.1.47	DisplayString	read-write	The name of this card
OCT cardCktGroupTrap	1.3.6.1.4.1.277.1.7.2.1.48	OCTET STRING	read-only	This is a ( 4 + n*134 ) byte octet string where n => 1. The first and second byte is the interface/slot id of the link/IOP going down or link goes up. The third byte is the reason why circuits go down: 1 is a user link goes down, 2 is a trunk link goes down, 3 is an IOP goes down and 4 is an user link goes up The fourth byte is the count of entries in the following circuit bit map array. Each circuit bit map entry is 134 bytes. The first 2 bytes is the IOP slot on which dlci's are defined. The second 2 bytes is the Physical port ID on which dlci's are defined. The third 2 bytes is the interface id on which dlci's are defined. The following 128 bytes (1024 bits) is a bit map for dlci's defined on the interface. The left-most bit of the first byte represent dlci 0 and the right-most bit of the 128th byte represent dlci 1023. If a bit is set, it means the corresponding dlci on that interface is up/down.
CTR cardOutBtus	1.3.6.1.4.1.277.1.7.2.1.49	Counter	read-only	The number of bus transfer units sent by this card.
CTR cardInGoodBtus	1.3.6.1.4.1.277.1.7.2.1.50	Counter	read-only	The number of good bus transfer units received by this card.
CTR cardInErrorBtus	1.3.6.1.4.1.277.1.7.2.1.51	Counter	read-only	The number of bus transfer units received with errors.
CTR cardInNoVcBtus	1.3.6.1.4.1.277.1.7.2.1.52	Counter	read-only	The number of bus transfer units discarded because no circuit was found.
CTR cardInLinkDownBtus	1.3.6.1.4.1.277.1.7.2.1.53	Counter	read-only	The number of bus transfer units discarded because the outgoing link was inactive.
CTR cardInNoBufferBtus	1.3.6.1.4.1.277.1.7.2.1.54	Counter	read-only	The number of bus transfer units discarded because no buffer was available.
CTR cardInForwardBitBtus	1.3.6.1.4.1.277.1.7.2.1.55	Counter	read-only	The number of bus transfer units discarded because the circuit forward bit was off.
INT cardDiagTestId	1.3.6.1.4.1.277.1.7.2.1.56	INTEGER	read-write	Identification of the diagnostics tests to be run.
INT cardDiagTestRuns	1.3.6.1.4.1.277.1.7.2.1.57	INTEGER	read-write	The number of passes of the diagnostics tests to be run. The default value is 1.
INT cardDiagState	1.3.6.1.4.1.277.1.7.2.1.58	INTEGER	read-write	The current state of the foreground diagnostics on this card.
OCT cardDiagOptionStr	1.3.6.1.4.1.277.1.7.2.1.59	OCTET STRING	read-write	Optional parameters to the diagnostic.
CTR cardDiagPasses	1.3.6.1.4.1.277.1.7.2.1.60	Counter	read-only	Number of successful diagnostic passes.
CTR cardDiagFailures	1.3.6.1.4.1.277.1.7.2.1.61	Counter	read-only	Number of failed diagnostic passes.
STR cardDiagResultString	1.3.6.1.4.1.277.1.7.2.1.62	DisplayString	read-only	Description of last diagnostic failure.
GAU cardFrameMemoryUtil	1.3.6.1.4.1.277.1.7.2.1.63	Gauge	read-only	The percentage of frame memory utilization on this intelligent card.
INT cardResetPram	1.3.6.1.4.1.277.1.7.2.1.64	INTEGER	read-write	Setting this to 1 causes a reset of PRAM on the corresponding card.
GAU cardMemoryUtil	1.3.6.1.4.1.277.1.7.2.1.65	Gauge	read-only	The percentage of system memory utilization on this intelligent card.
GAU cardFrameMemoryUsage	1.3.6.1.4.1.277.1.7.2.1.66	Gauge	read-only	The frame memory utilization, in terms of free bytes, for this intelligent card.
TIK cardUpTime	1.3.6.1.4.1.277.1.7.2.1.67	TimeTicks	read-only	The time (in hundredths of a second) since this card was last booted.
INT cardPramChecksum	1.3.6.1.4.1.277.1.7.2.1.68	INTEGER	read-only	The PRAM checksum for this card.
INT cardPhysicalIndex	1.3.6.1.4.1.277.1.7.2.1.69	INTEGER	read-only	The physical slot id of this card.
INT cardExternalClockRate	1.3.6.1.4.1.277.1.7.2.1.70	INTEGER	read-only	The external clock rate for DSX1, T1 and E1 cards. The value is specified in units of 8KHz and can range from 1 to 255.
INT cardShootState	1.3.6.1.4.1.277.1.7.2.1.71	INTEGER	read-write	Specifies whether the system monitor on the CP should shoot this card if it's unreachable. The default is enabled. The card index used in the binding refers to a physical card.
INT cardEraseAll	1.3.6.1.4.1.277.1.7.2.1.72	INTEGER	read-write	When set to 1, erases program flash and PRAM on specified card.
INT cardAdminCapability	1.3.6.1.4.1.277.1.7.2.1.73	INTEGER	read-write	The desired capability of the card
INT cardOperCapability	1.3.6.1.4.1.277.1.7.2.1.74	INTEGER	read-only	The actual capability of the card
INT cardISDNswtype	1.3.6.1.4.1.277.1.7.2.1.75	INTEGER	read-write	Specifies the ISDN central office switch type for the card.
GAU cardCpuFgUtil	1.3.6.1.4.1.277.1.7.2.1.76	Gauge	read-only	The CPU foreground utilization percentage for packet processing on this intelligent card.
INT cardTrkProtState	1.3.6.1.4.1.277.1.7.2.1.77	INTEGER	read-write	Control for issue of Link Trunk Protocol request frames. If set to disabled, the issue of trunk protocol requests is blocked for all trunks on this card.
INT cardISDNSigType	1.3.6.1.4.1.277.1.7.2.1.78	INTEGER	read-write	Specifies whether the ISDN Signalling type is Associated or Non-Facility Associated Signalling
INT cardISDNChanId	1.3.6.1.4.1.277.1.7.2.1.79	INTEGER	read-write	Specifies whether Channel ID assignment is performed by the central office switch or the 9000 - Exclusive (central office) Preferred (9000)
INT cardTransmitClockConfig	1.3.6.1.4.1.277.1.7.2.1.80	INTEGER	read-write	The transmit clock source for timing section of the card
INT cardTransmitClockSwitchOver	1.3.6.1.4.1.277.1.7.2.1.81	INTEGER	read-write	Enable/disable automatic transmit clock source switch-over once a failed clock reference has recovered.
INT cardTransmitClockStatus	1.3.6.1.4.1.277.1.7.2.1.82	INTEGER	read-only	The transmit clock PLL synchronization status of the card
INT cardSystemPrimaryClockPortConfig	1.3.6.1.4.1.277.1.7.2.1.83	INTEGER	read-write	The port number (1-x) on the card that specifies the system primary clock source. A zero specifies no port
INT cardSystemPrimaryClockStatus	1.3.6.1.4.1.277.1.7.2.1.84	INTEGER	read-only	The system primary clock status as detected on the card. On the BIO, this refers to the Timing Module 1 clock status as detected by the BIO.
INT cardSystemSecondaryClockPortConfig	1.3.6.1.4.1.277.1.7.2.1.85	INTEGER	read-write	The port number (1 to x) on the card that specifies the system secondary clock source. A zero specifies no port
INT cardSystemSecondaryClockStatus	1.3.6.1.4.1.277.1.7.2.1.86	INTEGER	read-only	The system secondary clock status as detected on the card. On the BIO, this refers to the Timing Module 2 clock status as detected by the BIO.
CTR cardInCells	1.3.6.1.4.1.277.1.7.2.1.87	Counter	read-only	The total number of cells received on this card.
CTR cardInErrorCells	1.3.6.1.4.1.277.1.7.2.1.88	Counter	read-only	The total number of cells received on this card with HEC error.
CTR cardInErrorVPIVCI	1.3.6.1.4.1.277.1.7.2.1.89	Counter	read-only	The total number of cells received with HEC invalid VPI, VCI.
CTR cardOutCells	1.3.6.1.4.1.277.1.7.2.1.90	Counter	read-only	The total number of cells transmitted out of this card
CTR cardOutDiscardCells	1.3.6.1.4.1.277.1.7.2.1.91	Counter	read-only	The total number of cells discarded due to congestion on this card
INT cardQOSQueueSize	1.3.6.1.4.1.277.1.7.2.1.92	INTEGER	read-only	The ATM QOS queue size (per cell) of each port on the card
INT cardLastErrorPort	1.3.6.1.4.1.277.1.7.2.1.93	INTEGER	read-only	The port number (1 to x) of the last cell with invalid cell header on the card
INT cardLastErrorVPI	1.3.6.1.4.1.277.1.7.2.1.94	INTEGER	read-only	The VPI of the last cell with invalid cell header on the card
INT cardLastErrorVCI	1.3.6.1.4.1.277.1.7.2.1.95	INTEGER	read-only	The VCI of the last cell with invalid cell header on the card
INT cardSystemPrimaryClockModeConfig	1.3.6.1.4.1.277.1.7.2.1.96	INTEGER	read-write	The system primary clock mode. PLCP is for DS3 port only
INT cardSystemSecondaryClockModeConfig	1.3.6.1.4.1.277.1.7.2.1.97	INTEGER	read-write	The system secondary clock mode. PLCP is for DS3 port only
INT cardNFBDEStatus	1.3.6.1.4.1.277.1.7.2.1.98	INTEGER	read-write	Non Fatal Background Diagnostic Error Status
STR cardProductCode	1.3.6.1.4.1.277.1.7.2.1.99	DisplayString	read-only	This card's product code.
STR cardMfgPN	1.3.6.1.4.1.277.1.7.2.1.100	DisplayString	read-only	This card's manufacturing part number.
TIK cardTotalUpTime	1.3.6.1.4.1.277.1.7.2.1.101	TimeTicks	read-only	This card's total accumulated up time, in hours.
INT cardIOAType	1.3.6.1.4.1.277.1.7.2.1.102	INTEGER	read-only	The type of IOA attached to this card.
STR cardIOAHwRev	1.3.6.1.4.1.277.1.7.2.1.103	DisplayString	read-only	The attached IOA's hardware revision.
STR cardIOASerial	1.3.6.1.4.1.277.1.7.2.1.104	DisplayString	read-only	The attached IOA's serial number.
STR cardIOAProductCode	1.3.6.1.4.1.277.1.7.2.1.105	DisplayString	read-only	The attached IOA's product code.
STR cardIOAMfgPN	1.3.6.1.4.1.277.1.7.2.1.106	DisplayString	read-only	The attached IOA's manufacturing part number.
INT cardDS0Support	1.3.6.1.4.1.277.1.7.2.1.107	INTEGER	read-only	Some B-Stdx T1 boards do not support lpbk.
INT cardDiagParamId	1.3.6.1.4.1.277.1.7.2.1.108	INTEGER	read-write	Parameter identifier for internal diagnostics.
INT cardDiagParamValue	1.3.6.1.4.1.277.1.7.2.1.109	INTEGER	read-write	Value assigned to parameter specified by cardDiagParamId.
INT cardBulkStatsPeakCapability	1.3.6.1.4.1.277.1.7.2.1.110	INTEGER	read-write	Configures capability to collect peak 5-minute statistics. Capability change takes effect upon IOM reboot.
INT cardBulkStatsTotalCapability	1.3.6.1.4.1.277.1.7.2.1.111	INTEGER	read-write	Configures capability to collect total statistics. Capability change takes effect upon IOM reboot.
INT cardBulkStatsPeakEnable	1.3.6.1.4.1.277.1.7.2.1.112	INTEGER	read-write	Reflects the operational state of the peak 5-minute statistic collection on an IOM. For this setting to be enabled, the respective capability must be enabled.
INT cardBulkStatsTotalEnable	1.3.6.1.4.1.277.1.7.2.1.113	INTEGER	read-write	Reflects the operational state of the total statistic collection on an IOM. For this setting to be enabled, the respective capability must be enabled.
INT cardBulkStatsBaseCollectPeriod	1.3.6.1.4.1.277.1.7.2.1.114	INTEGER	read-write	Configures base collection period for bulk statistics on an IOM in minutes. Only the following values are allowed: 15, 20, 30, 60, 120, 180, 240, 360, 720, 1440. The default value is 60.
INT cardNrtsHwRev	1.3.6.1.4.1.277.1.7.2.1.115	INTEGER	read-only	Hardware revision of the NRTS processor.
INT cardNrtsOutCellBufSize	1.3.6.1.4.1.277.1.7.2.1.116	INTEGER	read-only	The size of the NRTS output cell buffer.
INT cardNrtsOperState	1.3.6.1.4.1.277.1.7.2.1.117	INTEGER	read-only	The operational status of the NRTS processor.
INT cardNrtsAdminState	1.3.6.1.4.1.277.1.7.2.1.118	INTEGER	read-write	The admin status of the NRTS processor.
INT cardNrtsCcrmProtocolId	1.3.6.1.4.1.277.1.7.2.1.119	INTEGER	read-write	The protocol ID field for the CCRM cells. Must be different from the BCM protocol ID. Default is 6.
INT cardNrtsBcmProtocolId	1.3.6.1.4.1.277.1.7.2.1.120	INTEGER	read-write	The protocol ID field for the BCM cells. Must be different from the CCRM protocol ID. Default is 5.
INT cardNrtsRmGenInterval	1.3.6.1.4.1.277.1.7.2.1.121	INTEGER	read-write	The RM cell generation interval in ms. Minimum is 30, maximum is 250, default is 100.
INT cardNrtsIdleCktThresh	1.3.6.1.4.1.277.1.7.2.1.122	INTEGER	read-write	The number of RM cell generation intervals with no cell reception upon which the circuit is declared idle. Minimum is 1, maximum is 8, default is 8.
INT cardNrtsVbrNrtManage	1.3.6.1.4.1.277.1.7.2.1.123	INTEGER	read-write	Indicates whether VBR NRT traffic should be managed by the NRTS processor.
INT cardNrtsIcrFact	1.3.6.1.4.1.277.1.7.2.1.124	INTEGER	read-write	A factor used to calculate the Initial Cell Rate for a circuit from its MCR and PCR.
INT cardNrtsMcastDiscardThresh	1.3.6.1.4.1.277.1.7.2.1.125	INTEGER	read-write	A NRTS discard threshold for the multicast circuits.
CTR cardNrtsMcastDiscardCount	1.3.6.1.4.1.277.1.7.2.1.126	Counter	read-only	A NRTS discard counter for the multicast circuits.
INT cardAdminIOAType	1.3.6.1.4.1.277.1.7.2.1.127	INTEGER	read-write	The type of IOA attached to this card viewed from NMS.
INT cardNrtsMcastRate	1.3.6.1.4.1.277.1.7.2.1.128	INTEGER	read-write	The NRTS shaping rate for multicast circuits as a fraction of the line rate.
INT cardMonStatus	1.3.6.1.4.1.277.1.7.2.1.129	INTEGER	read-write	Set MON960 status, default(1) -- enable, 2 -- disable.
STR cardImageSetA	1.3.6.1.4.1.277.1.7.2.1.130	DisplayString	read-only	The details of Image Set A. The elements of each image are space delimited and include Part Number, Revision, Size and Description. The details of each image are linefeed delimited.
STR cardImageSetB	1.3.6.1.4.1.277.1.7.2.1.131	DisplayString	read-only	The details of Image Set B. The elements of each image are space delimited and include Part Number, Revision, Size and Description. The details of each image are linefeed delimited.
STR cardMacAddress	1.3.6.1.4.1.277.1.7.2.1.132	DisplayString	read-only	ethernet MAC address of the card if there is an ethernet interface. Currently only CP cards may have ethernet. Cards without ethernet return 0 length octet string.
STR cardFlashRev	1.3.6.1.4.1.277.1.7.2.1.133	DisplayString	read-only	The boot flash rev number.
INT cardRequiredCapabilityBitmask	1.3.6.1.4.1.277.1.7.2.1.134	INTEGER	read-only	Bitmask indicating this cards' required capabilities based on configured features. A bit is set to one if the corresponding capability is required. This variable is a bitmask so only power-of-2 values can be assigned (1,2,4,8,16,etc.) .
INT cardOperCapabilityBitmask	1.3.6.1.4.1.277.1.7.2.1.135	INTEGER	read-only	Bitmask indicating this cards' actual capabilities. A bit is set to one if the corresponding capability is supported. This variable is a bitmask so only power-of-2 values can be assigned (1,2,4,8,16,etc.).
OCT cardDslModule	1.3.6.1.4.1.277.1.7.2.1.136	OCTET STRING	read-write	This is for Dynamic Software Loadl You can type: ModuleName Version, ModuleName Version, ... to load modules.
INT cardIPTableSize	1.3.6.1.4.1.277.1.7.2.1.137	INTEGER	read-write	The maximum number of IP routing table entries supported by the card. If set to 0, routing table size is assumed unlimited.
INT cardIPTableState	1.3.6.1.4.1.277.1.7.2.1.138	INTEGER	read-only	State of the card's IP routing table. If set to marginal, the routing table maximum size has been exceeded. and all routes except management prefixes have been discarded.
INT cardATMTcaInBufOverflowAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.139	INTEGER	read-write	The atm tca ingress buffer overflow alert period (in min).
INT cardATMTcaInBufOverflowThresh	1.3.6.1.4.1.277.1.7.2.1.140	INTEGER	read-write	The atm tca ingress buffer overflow threshold.
INT cardATMTcaInInvalidVpiVciAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.141	INTEGER	read-write	The atm tca ingress invalid vpi/vci alert period (in min).
INT cardATMTcaInInvalidVpiVciThresh	1.3.6.1.4.1.277.1.7.2.1.142	INTEGER	read-write	The atm tca ingress invalid vpi/vci threshold.
INT cardATMTcaInATMDCFullAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.143	INTEGER	read-write	The atm tca ingress ATM DC full alert period (in min).
INT cardATMTcaInATMDCFullThresh	1.3.6.1.4.1.277.1.7.2.1.144	INTEGER	read-write	The atm tca ingress ATM DC full threshold.
INT cardATMTcaEnable	1.3.6.1.4.1.277.1.7.2.1.145	INTEGER	read-write	The atm tca enable/disable.
INT cardATMTcaId	1.3.6.1.4.1.277.1.7.2.1.146	INTEGER	read-only	This object identifies the the most recently declared card ATM threshold crossing alert
INT cardATMTcaECidLookupFailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.147	INTEGER	read-write	The atm tca ingress buffer overflow alert period (in min).
INT cardATMTcaECidLookupThresh	1.3.6.1.4.1.277.1.7.2.1.148	INTEGER	read-write	The atm tca ingress buffer overflow threshold.
INT cardATMTcaSPPearlOCbrFailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.149	INTEGER	read-write	The atm tca sp pearl overflow CBR alert period (in min).
INT cardATMTcaSPPearlOCbrThresh	1.3.6.1.4.1.277.1.7.2.1.150	INTEGER	read-write	The atm tca sp pearl overflow CBR threshold.
INT cardATMTcaSPPearlOAbrFailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.151	INTEGER	read-write	The atm tca sp pearl overflow ABR alert period (in min).
INT cardATMTcaSPPearlOAbrThresh	1.3.6.1.4.1.277.1.7.2.1.152	INTEGER	read-write	The atm tca sp pearl overflow ABR threshold.
INT cardATMTcaSPPearlOVbr1FailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.153	INTEGER	read-write	The atm tca sp pearl overflow VBR1 alert period (in min).
INT cardATMTcaSPPearlOVbr1Thresh	1.3.6.1.4.1.277.1.7.2.1.154	INTEGER	read-write	The atm tca sp pearl overflow VBR1 threshold.
INT cardATMTcaSPPearlOVbr2FailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.155	INTEGER	read-write	The atm tca sp pearl overflow VBR2 alert period (in min).
INT cardATMTcaSPPearlOVbr2Thresh	1.3.6.1.4.1.277.1.7.2.1.156	INTEGER	read-write	The atm tca sp pearl overflow VBR2 threshold.
INT cardATMTcaSPPearlGCbrFailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.157	INTEGER	read-write	The atm tca sp pearl congestion CBR alert period (in min).
INT cardATMTcaSPPearlGCbrThresh	1.3.6.1.4.1.277.1.7.2.1.158	INTEGER	read-write	The atm tca sp pearl congestion CBR threshold.
INT cardATMTcaSPPearlGAbrFailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.159	INTEGER	read-write	The atm tca sp pearl congestion ABR alert period (in min).
INT cardATMTcaSPPearlGAbrThresh	1.3.6.1.4.1.277.1.7.2.1.160	INTEGER	read-write	The atm tca sp pearl congestion ABR threshold.
INT cardATMTcaSPPearlGVbr1FailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.161	INTEGER	read-write	The atm tca sp pearl congestion VBR1 alert period (in min).
INT cardATMTcaSPPearlGVbr1Thresh	1.3.6.1.4.1.277.1.7.2.1.162	INTEGER	read-write	The atm tca sp pearl congestion VBR1 threshold.
INT cardATMTcaSPPearlGVbr2FailureAlertPeriod	1.3.6.1.4.1.277.1.7.2.1.163	INTEGER	read-write	The atm tca sp pearl congestion VBR2 alert period (in min).
INT cardATMTcaSPPearlGVbr2Thresh	1.3.6.1.4.1.277.1.7.2.1.164	INTEGER	read-write	The atm tca sp pearl congestion VBR2 threshold.
INT cardATMTcaSPEnable	1.3.6.1.4.1.277.1.7.2.1.165	INTEGER	read-write	The atm tca SP enable/disable.
INT cardSPEFCIEnable	1.3.6.1.4.1.277.1.7.2.1.166	INTEGER	read-write	The atm EFCI marking enable/disable.
INT cardSPClpEnable	1.3.6.1.4.1.277.1.7.2.1.167	INTEGER	read-write	The atm CLP-1 enable/disable.
INT spATMTcaId	1.3.6.1.4.1.277.1.7.2.1.168	INTEGER	read-only	This object identifies the the most recently declared sp ATM threshold crossing alert and first byte is used to indicate the switching port number. i.e. sp 1 has spBufferOverflowC, then the value is 0x1001
CAR cardSubcardToRedundant	1.3.6.1.4.1.277.1.7.2.1.169	CardTypes	read-write	Commands the card to initiate an immediate protection switch on the identified subcard that it controls. This causes control to be switched from the active card to the standby card.
GAU cardMemory5Usage	1.3.6.1.4.1.277.1.7.2.1.170	Gauge	read-only	The bank5 memory utilization, in terms of free bytes, for CP Oynx card only.
CAR cardSF1OperStatus	1.3.6.1.4.1.277.1.7.2.1.171	CardStatuses	read-only	The current status of Switch Fabric 1 (GX550).
CAR cardSF2OperStatus	1.3.6.1.4.1.277.1.7.2.1.172	CardStatuses	read-only	The current status of Switch Fabric 2 (GX550).
CAR cardTM1OperStatus	1.3.6.1.4.1.277.1.7.2.1.173	CardStatuses	read-only	The current status of Timing Module 1 (GX550).
CAR cardTM2OperStatus	1.3.6.1.4.1.277.1.7.2.1.174	CardStatuses	read-only	The current status of Timing Module 2 (GX550).
INT cardMemStartLog	1.3.6.1.4.1.277.1.7.2.1.175	INTEGER	read-write	Enable/Disable Memory log record, 1 -- enable, 0 -- disable.
INT cardMemLogLevel	1.3.6.1.4.1.277.1.7.2.1.176	INTEGER	read-write	Set the Memory log level. Default 6
INT cardMemClrLog	1.3.6.1.4.1.277.1.7.2.1.177	INTEGER	read-write	Enable/Disable Clear Memory log, 1 -- clear, 0 (default) -- not clear.
INT cardValidSubcards	1.3.6.1.4.1.277.1.7.2.1.178	INTEGER	read-only	The number of manageable subcards physically present in this card.
INT cardClp0CbrThreshold	1.3.6.1.4.1.277.1.7.2.1.179	INTEGER	read-write	The CLP 0 threshold for CBR queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the threshold.
INT cardClp01CbrThreshold	1.3.6.1.4.1.277.1.7.2.1.180	INTEGER	read-write	The maximum length of CBR queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold.
INT cardClp0VbrRtThreshold	1.3.6.1.4.1.277.1.7.2.1.181	INTEGER	read-write	The CLP 0 threshold for VBR RT queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the threshold.
INT cardClp01VbrRtThreshold	1.3.6.1.4.1.277.1.7.2.1.182	INTEGER	read-write	The maximum length of VBR-RT queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold.
INT cardClp0VbrNrtThreshold	1.3.6.1.4.1.277.1.7.2.1.183	INTEGER	read-write	The CLP 0 threshold for VBR NRT queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the threshold.
INT cardClp01VbrNrtThreshold	1.3.6.1.4.1.277.1.7.2.1.184	INTEGER	read-write	The maximum length of VBR-NRT queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold.
INT cardClp0UAbrThreshold	1.3.6.1.4.1.277.1.7.2.1.185	INTEGER	read-write	The CLP 0 threshold for ABR/UBR queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the threshold.
INT cardClp01UAbrThreshold	1.3.6.1.4.1.277.1.7.2.1.186	INTEGER	read-write	The maximum length of UBR/ABR queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold.
CTR cardControlMessagesFromBus	1.3.6.1.4.1.277.1.7.2.1.187	Counter	read-write	The number of complete control Messages received over the Cell Bus for this card.
CTR cardControlMessagesToBus	1.3.6.1.4.1.277.1.7.2.1.188	Counter	read-write	The number of complete control Messages transmitted by this card over the Cell Bus.
CTR cardBTUsFromBus	1.3.6.1.4.1.277.1.7.2.1.189	Counter	read-write	The number of BTUs received by this card over the Cell Bus.
CTR cardBTUsToBus	1.3.6.1.4.1.277.1.7.2.1.190	Counter	read-write	The number of BTUs transmitted by this card over the Cell Bus.
CTR cardInvalidPvcBTUs	1.3.6.1.4.1.277.1.7.2.1.191	Counter	read-write	The number of BTUs received by this card over the Cell Bus with an invalid PVC identifier.
CTR cardIncompleteFramesFromBus	1.3.6.1.4.1.277.1.7.2.1.192	Counter	read-write	The number of partial frames received by this card over the Cell Bus which were discarded due to missing BTUs.
CTR cardBTUsBusErrors	1.3.6.1.4.1.277.1.7.2.1.193	Counter	read-write	The number of BTUs received by this card over the Cell Bus which were discarded due to errors.
CTR cardBTUsNoResource	1.3.6.1.4.1.277.1.7.2.1.194	Counter	read-write	The number of BTUs received by this card over the Cell Bus which were discarded due to no free BTUs available to replace it.
INT cardInvalidPvcBTUsThreshold	1.3.6.1.4.1.277.1.7.2.1.195	INTEGER	read-write	Send trap if the number of BTUs received by this card over the Cell Bus with an invalid PVC identifier exceeds this in a one minute interval. Zero value implies no check.
INT cardIncompleteFramesFromBusThreshold	1.3.6.1.4.1.277.1.7.2.1.196	INTEGER	read-write	Send trap if the number of partial frames received by this card over the Cell Bus which were discarded due to missing BTUs exceeds this in a one minute interval. Zero value implies no check.
INT cardBTUsBusErrorThreshold	1.3.6.1.4.1.277.1.7.2.1.197	INTEGER	read-write	Send trap if the number of BTUs received by this card over the Cell Bus which were discarded due to errors exceeds this in a one minute interval. Zero value implies no check.
INT cardBTUsNoResourceThreshold	1.3.6.1.4.1.277.1.7.2.1.198	INTEGER	read-write	Send trap if the number of BTUs received by this card over the Cell Bus which were discarded due to no free BTUs available to replace it exceeds this in a one minute interval. Zero value implies no check.
INT cardFrameMemoryThreshold	1.3.6.1.4.1.277.1.7.2.1.199	INTEGER	read-write	The percentage of frame memory utilization on this card which will generate a trap. Zero value implies no check.
CTR cardHoldQFrameMemory	1.3.6.1.4.1.277.1.7.2.1.200	Counter	read-only	The frame memory utilization, in terms of bytes, currently on the Hold Queues for this card.
CTR cardTotalAAL5RxErrorCount	1.3.6.1.4.1.277.1.7.2.1.201	Counter	read-only	The total number of Rx errors detected by the AAL5 processor on this card.
INT cardOperMemSize	1.3.6.1.4.1.277.1.7.2.1.202	INTEGER	read-only	The total memory size on this card, in MB (1024 Kbytes).
ds1	1.3.6.1.4.1.277.1.8
dsx1ConfigTable	1.3.6.1.4.1.277.1.8.1		not-accessible	The DS1 Configuration table.
dsx1ConfigEntry	1.3.6.1.4.1.277.1.8.1.1		not-accessible	An entry in the DS1 Configuration table.
INT dsx1SlotId	1.3.6.1.4.1.277.1.8.1.1.1	INTEGER	read-only	The slot number of the corresponding DS1.
INT dsx1PortId	1.3.6.1.4.1.277.1.8.1.1.2	INTEGER	read-only	The port number of the corresponding DS1 on the board.
INT dsx1TimeElapsed	1.3.6.1.4.1.277.1.8.1.1.3	INTEGER	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period.
INT dsx1ValidIntervals	1.3.6.1.4.1.277.1.8.1.1.4	INTEGER	read-only	The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online.
INT dsx1LineType	1.3.6.1.4.1.277.1.8.1.1.5	INTEGER	read-only	This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: dsx1ESF Extended SuperFrame DS1 dsx1D4 AT&T D4 format DS1 dsx1E1 CCITT Recommendation G.704 (Table 4a) dsx1E1-CRC CCITT Recommendation G.704 (Table 4b) dsxE1-MF G.704 (Table 4a) with TS16 multiframing enabled dsx1E1-CRC-MF G.704 (Table 4b) with TS16 multiframing enabled
INT dsx1LineCoding	1.3.6.1.4.1.277.1.8.1.1.6	INTEGER	read-only	This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS refers the Jammed Bit Zero Suppres- sion, in which the AT&T specification of at least one pulse every 8 bit periods is literal- ly implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data. dsx1B8ZS refers to the use of a specified pat- tern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. ANSI Clear Channels may use dsx1ZBTSI, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use dsx1HDB3 or dsx1AMI. dsx1AMI refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
INT dsx1SendCode	1.3.6.1.4.1.277.1.8.1.1.7	INTEGER	read-only	This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal data dsx1SendLineCode sending a request for a line loopback dsx1SendPayloadCode sending a request for a payload loopback dsx1SendResetCode sending a loopback termination request dsx1SendQRS sending a Quasi-Random Signal (QRS) test pattern dsx1Send511Pattern sending a 511 bit fixed test pattern dsx1Send3in24Pattern sending a fixed test pattern of 3 bits set in 24 dsx1SendOtherTestPattern sending a test pattern other than those described by this object
STR dsx1CircuitIdentifier	1.3.6.1.4.1.277.1.8.1.1.8	DisplayString	read-only	This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.
INT dsx1LoopbackConfig	1.3.6.1.4.1.277.1.8.1.1.9	INTEGER	read-only	This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean: dsx1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. dsx1PayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for re- transmission after it has passed through the device's framing function. dsx1LineLoop The received signal at this interface does not go through the device (minimum pene- tration) but is looped back out. dsx1OtherLoop Loopbacks that are not defined here.
INT dsx1LineStatus	1.3.6.1.4.1.277.1.8.1.1.10	INTEGER	read-only	This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alarm' infor- mation. The dsx1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. dsx1NoAlarm should be set if and only if no other flag is set. If the dsx1LoopbackState bit is set, the loopback in ef- fect can be determined from the dsx1LoopbackConfig object. The various bit positions are: 1 dsx1NoAlarm No Alarm Present 2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm) 4 dsx1XmtFarEndLOF Near end sending LOF Indication 8 dsx1RcvAIS Far end sending AIS 16 dsx1XmtAIS Near end sending AIS 32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm) 64 dsx1LossOfSignal Near end Loss Of Signal 128 dsx1LoopbackState Near end is looped 256 dsx1T16AIS E1 TS16 AIS 512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF 1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF 2048 dsx1RcvTestCode Near End detects a test code 4096 dsx1OtherFailure any line status not defined here
INT dsx1SignalMode	1.3.6.1.4.1.277.1.8.1.1.11	INTEGER	read-only	'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Sig- naling is in use. 'bitOriented' indicates that E1 Channel Asso- ciated Signaling is in use. 'messageOriented' indicates that Common Chan- nel Signaling is in use either on channel 16 of an E1 link or channel 24 of a T1.
INT dsx1TransmitClockSource	1.3.6.1.4.1.277.1.8.1.1.12	INTEGER	read-only	The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used. 'throughTiming' indicates that recovered re- ceive clock from another interface is used as the transmit clock.
INT dsx1Fdl	1.3.6.1.4.1.277.1.8.1.1.13	INTEGER	read-only	This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following is used. 'dsx1Ansi-T1-403' refers to the FDL exchange recommended by ANSI. 'dsx1Att-54016' refers to ESF FDL exchanges. 'dsx1Fdl-none' indicates that the device does not use the FDL.
INT dsx1FdlVersion	1.3.6.1.4.1.277.1.8.1.1.14	INTEGER	read-only	The version of the Dallas FDL firmware
dsx1CurrentTable	1.3.6.1.4.1.277.1.8.2		not-accessible	The DS1 Current table.
dsx1CurrentEntry	1.3.6.1.4.1.277.1.8.2.1		not-accessible	An entry in the DS1 Current table.
INT dsx1CurrentSlotId	1.3.6.1.4.1.277.1.8.2.1.1	INTEGER	read-only	The slot number of the corresponding DS1.
INT dsx1CurrentPortId	1.3.6.1.4.1.277.1.8.2.1.2	INTEGER	read-only	The port number of the corresponding DS1 on the board.
GAU dsx1CurrentESs	1.3.6.1.4.1.277.1.8.2.1.3	Gauge	read-only	The number of Errored Seconds, encountered by a DS1 interface in the current 15 minute inter- val.
GAU dsx1CurrentSESs	1.3.6.1.4.1.277.1.8.2.1.4	Gauge	read-only	The number of Severely Errored Seconds encoun- tered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentSEFSs	1.3.6.1.4.1.277.1.8.2.1.5	Gauge	read-only	The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentUASs	1.3.6.1.4.1.277.1.8.2.1.6	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in the current 15 minute in- terval.
GAU dsx1CurrentCSSs	1.3.6.1.4.1.277.1.8.2.1.7	Gauge	read-only	The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentBESs	1.3.6.1.4.1.277.1.8.2.1.8	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current 15 minute interval.
dsx1IntervalTable	1.3.6.1.4.1.277.1.8.3		not-accessible	The DS1 Interval table.
dsx1IntervalEntry	1.3.6.1.4.1.277.1.8.3.1		not-accessible	An entry in the DS1 Interval table.
INT dsx1IntervalSlotId	1.3.6.1.4.1.277.1.8.3.1.1	INTEGER	read-only	The slot number of the corresponding DS1.
INT dsx1IntervalPortId	1.3.6.1.4.1.277.1.8.3.1.2	INTEGER	read-only	The port number of the corresponding DS1 on the board.
INT dsx1IntervalNumber	1.3.6.1.4.1.277.1.8.3.1.3	INTEGER	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming that all 96 intervals are valid).
GAU dsx1IntervalESs	1.3.6.1.4.1.277.1.8.3.1.4	Gauge	read-only	The number of Errored Seconds encountered by a DS1 interface in one of the previous 96, indi- vidual 15 minute, intervals.
GAU dsx1IntervalSESs	1.3.6.1.4.1.277.1.8.3.1.5	Gauge	read-only	The number of Severely Errored Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalSEFSs	1.3.6.1.4.1.277.1.8.3.1.6	Gauge	read-only	The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalUASs	1.3.6.1.4.1.277.1.8.3.1.7	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalCSSs	1.3.6.1.4.1.277.1.8.3.1.8	Gauge	read-only	The number of Controlled Slip Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalBESs	1.3.6.1.4.1.277.1.8.3.1.9	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
dsx1TotalTable	1.3.6.1.4.1.277.1.8.4		not-accessible	The DS1 Total table. 24 hour interval.
dsx1TotalEntry	1.3.6.1.4.1.277.1.8.4.1		not-accessible	An entry in the DS1 Total table.
INT dsx1TotalSlotId	1.3.6.1.4.1.277.1.8.4.1.1	INTEGER	read-only	The slot number of the corresponding DS1.
INT dsx1TotalPortId	1.3.6.1.4.1.277.1.8.4.1.2	INTEGER	read-only	The port number of the corresponding DS1 on the board.
GAU dsx1TotalESs	1.3.6.1.4.1.277.1.8.4.1.3	Gauge	read-only	The number of Errored Seconds encountered by a DS1 interface in the previous 24 hour interval
GAU dsx1TotalSESs	1.3.6.1.4.1.277.1.8.4.1.4	Gauge	read-only	The number of Severely Errored Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalSEFSs	1.3.6.1.4.1.277.1.8.4.1.5	Gauge	read-only	The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalUASs	1.3.6.1.4.1.277.1.8.4.1.6	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in the previous 24 hour in- terval.
GAU dsx1TotalCSSs	1.3.6.1.4.1.277.1.8.4.1.7	Gauge	read-only	The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalBESs	1.3.6.1.4.1.277.1.8.4.1.8	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 24 hour interval.
cascsmds	1.3.6.1.4.1.277.2
smdsaddr	1.3.6.1.4.1.277.2.1
smdsaddrTable	1.3.6.1.4.1.277.2.1.1		not-accessible	A list of smds adress entries.
smdsaddrEntry	1.3.6.1.4.1.277.2.1.1.1		not-accessible	An smds address and its associated information.
OCT smdsaddrAddr	1.3.6.1.4.1.277.2.1.1.1.1	OCTET STRING	read-write	SMDS address. The 4 most significant bits are the address type : 1100 for an individual address, 1110 for a group address. The following 4 bits are 0001. The following 5 bytes are the 10 digits number in BCD format. The following 16 bits are padded with 1's
INT smdsaddrType	1.3.6.1.4.1.277.2.1.1.1.2	INTEGER	read-write	SMDS address internal type.
INT smdsaddrId	1.3.6.1.4.1.277.2.1.1.1.3	INTEGER	read-write	smds address internal ID. Range from 1 to 192 for local individual addresses. Range from 193 to 704 for Alien individual addresses. Range from 1 to 64 for local group addresses. Range from 65 to 576 for alien group addresses.
INT smdsaddrIf	1.3.6.1.4.1.277.2.1.1.1.4	INTEGER	read-write	The interface to which this address is assigned.
OCT smdsaddrParentGrpMap	1.3.6.1.4.1.277.2.1.1.1.5	OCTET STRING	read-only	The parent group bit map. The bit position of each bit in this bit map represent a parent group address ID. The most significant bit is corresponding to group address ID 1. This MIB object applies to a local individual address only.
OCT smdsaddrParentScrnMap	1.3.6.1.4.1.277.2.1.1.1.6	OCTET STRING	read-only	This MIB object not applicable to switch software versions 03.99.00 and above. The parent screen bit map. The bit position of each bit in this bit map represent a parent screen ID. The most significant bit is corresponding to screen ID 1.
OCT smdsaddrMemberAddrMap	1.3.6.1.4.1.277.2.1.1.1.7	OCTET STRING	read-write	The member individual address bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit map. The bit position of each bit in this bit map represent a member local individual address ID. The most significant bit is corresponding to local individual address ID 1. For get response, The whole string is the bit map.
INT smdsaddrAdminStatus	1.3.6.1.4.1.277.2.1.1.1.8	INTEGER	read-write	administration status
INT smdsaddrSlot	1.3.6.1.4.1.277.2.1.1.1.9	INTEGER	read-write	The Slot in which this address is assigned.
INT smdsaddrSsiIfNum	1.3.6.1.4.1.277.2.1.1.1.10	INTEGER	read-write	The SSI to which this address is associated.
namebinding	1.3.6.1.4.1.277.3
namebindingTable	1.3.6.1.4.1.277.3.1		not-accessible	A table of name bindings to a set of logical ports.
namebindingEntry	1.3.6.1.4.1.277.3.1.1		not-accessible	The name binding entry contains objects relative to a name binding.
INT nameType	1.3.6.1.4.1.277.3.1.1.1	INTEGER	read-write	The name type.
OCT nameName	1.3.6.1.4.1.277.3.1.1.2	OCTET STRING	read-write	A name of the type indicated by nameType.
INT namePrimary	1.3.6.1.4.1.277.3.1.1.3	INTEGER	read-write	The current binding type for this entry.
INT nameIfIndex	1.3.6.1.4.1.277.3.1.1.4	INTEGER	read-write	The interface number of the logical port for this binding.
INT nameNodeId	1.3.6.1.4.1.277.3.1.1.5	INTEGER	read-only	The identifier number of the node for this binding.
INT nameStatus	1.3.6.1.4.1.277.3.1.1.6	INTEGER	read-write	The status of the binding.
isdnAddr	1.3.6.1.4.1.277.4
isdnAddrTable	1.3.6.1.4.1.277.4.1		not-accessible	A list of E.164 address entries.
isdnAddrEntry	1.3.6.1.4.1.277.4.1.1		not-accessible	Information about a single local E.164 address in the table. Setting this varible to 0 removes the entry.
INT isdnAddrIf	1.3.6.1.4.1.277.4.1.1.1	INTEGER	read-write	The interface id of the logical port in question
INT isdnChanType	1.3.6.1.4.1.277.4.1.1.3	INTEGER	read-write	type of logical port 0 => isdn b-channel, 1 => sw56
isdnCallerIDTable	1.3.6.1.4.1.277.4.2		not-accessible	A list of valid caller ids
isdnCallerIDEntry	1.3.6.1.4.1.277.4.2.1		not-accessible	Information about a single valid caller id.
INT isdnCallerIDIf	1.3.6.1.4.1.277.4.2.1.1	INTEGER	read-write	The interface id of the logical port in question
OCT isdnCallerIDAddr	1.3.6.1.4.1.277.4.2.1.2	OCTET STRING	read-write	ISDN address. The actual E164 number. For example, ISDN address 15086922600 is stored as string 15086922600.
INT isdnCallerAdminStatus	1.3.6.1.4.1.277.4.2.1.3	INTEGER	read-write	administration status
cascsvc	1.3.6.1.4.1.277.5
NTF svcAtmFailedCall	1.3.6.1.4.1.277.5.0.55			Notification that one or more SVC call failures have been logged in the svcAtmFailedCallTable.
NTF svcAtmSigStatusChange	1.3.6.1.4.1.277.5.0.56			Notification that the status of the ATM signalling function has changed on the port.
svcaddress	1.3.6.1.4.1.277.5.1
svcNodePrefixTable	1.3.6.1.4.1.277.5.1.1		not-accessible	A table of prefixes associated with this node.
svcNodePrefixEntry	1.3.6.1.4.1.277.5.1.1.1		not-accessible	The node prefix entry contains objects relevant to SVC prefixes associated with the node.
OCT svcNodePrefixPrefix	1.3.6.1.4.1.277.5.1.1.1.1	OCTET STRING	read-only	A prefix associated with this node. E.164 prefixes are coded as 1-15 ASCII octets with no leading padding required. ATM endsystem prefixes are coded as 1-20 binary octets. Unused bits in the last octet must be set to 0.
INT svcNodePrefixNumBits	1.3.6.1.4.1.277.5.1.1.1.2	INTEGER	read-write	The number of valid bits associated with this entry's prefix object. By default, this value will be 8 times the prefix object's octet string length.
INT svcNodePrefixNmbPlan	1.3.6.1.4.1.277.5.1.1.1.3	INTEGER	read-write	The numbering plan corresponding to this entry's prefix object.
INT svcNodePrefixAdminStatus	1.3.6.1.4.1.277.5.1.1.1.4	INTEGER	read-write	The status of this entry.
svcPrefixTable	1.3.6.1.4.1.277.5.1.2		not-accessible	A table of SVC address prefixes associated with ports on this node.
svcPrefixEntry	1.3.6.1.4.1.277.5.1.2.1		not-accessible	The prefix entry contains objects relevant to SVC prefixes associated with this port.
IND svcPrefixIfIndex	1.3.6.1.4.1.277.5.1.2.1.1	Index	read-only	The interface value of the corresponding MIB-II ifEntry.
OCT svcPrefixPrefix	1.3.6.1.4.1.277.5.1.2.1.2	OCTET STRING	read-only	A prefix associated with this port. E.164 prefixes are coded as 1-15 ASCII octets with no leading padding required. ATM endsystem prefixes are coded as 1-20 binary octets. Unused bits in the last octet must be set to 0. For ATM DCE ports, only, atm-endsystem prefixes with length 104 bits (13 octets) and all E.164 prefixes are eligible for ILMI address registration.
INT svcPrefixNumBits	1.3.6.1.4.1.277.5.1.2.1.3	INTEGER	read-write	The number of valid bits associated with this entry's prefix object. By default, this value will be 8 times the prefix object's octet string length.
INT svcPrefixNmbPlan	1.3.6.1.4.1.277.5.1.2.1.4	INTEGER	read-write	The numbering plan corresponding to this entry's prefix object.
INT svcPrefixAdminCost	1.3.6.1.4.1.277.5.1.2.1.5	INTEGER	read-write	This object is only relevant for ports connecting this network to another network and is used to represent the administrative cost of reaching destinations containing this entry's prefix value.
OCT svcPrefixLocalGatewayAddress	1.3.6.1.4.1.277.5.1.2.1.6	OCTET STRING	read-write	This object is only relevant for ports connecting this network to another network and is used to replace the calling party number when egress address translation is configured to the appropriate mode. E.164 addresses are coded as 1-15 ASCII octets Atm-endsystem addresses are coded as 20 octet binary addresses.
INT svcPrefixLocalGatewayNmbPlan	1.3.6.1.4.1.277.5.1.2.1.7	INTEGER	read-write	The numbering plan corresponding to this entry's local gateway address object.
OCT svcPrefixRemoteGatewayAddress	1.3.6.1.4.1.277.5.1.2.1.8	OCTET STRING	read-write	This object is only relevant for ports connecting this network to another network and is used to replace the calling party number when egress address translation is configured to the appropriate mode. E.164 addresses are coded as 1-15 ASCII octets Atm-endsystem addresses are coded as 20 octet binary addresses.
INT svcPrefixRemoteGatewayNmbPlan	1.3.6.1.4.1.277.5.1.2.1.9	INTEGER	read-write	The numbering plan corresponding to this entry's remote gateway address object.
INT svcPrefixAdminStatus	1.3.6.1.4.1.277.5.1.2.1.10	INTEGER	read-write	The status of this entry.
svcAddrTable	1.3.6.1.4.1.277.5.1.3		not-accessible	A table of SVC addresses associated with with ports on this node.
svcAddrEntry	1.3.6.1.4.1.277.5.1.3.1		not-accessible	The address entry contains objects relevant to SVC addresses associated with this port.
IND svcAddrIfIndex	1.3.6.1.4.1.277.5.1.3.1.1	Index	read-only	The interface value of the corresponding MIB-II ifEntry.
OCT svcAddrAddress	1.3.6.1.4.1.277.5.1.3.1.2	OCTET STRING	read-only	An address associated with this port. E.164 addresses are coded as 1-15 ASCII octets. ATM-Endsystem addresses are coded as 20 binary octets.
INT svcAddrNmbPlan	1.3.6.1.4.1.277.5.1.3.1.3	INTEGER	read-write	The numbering plan corresponding to this entry's address object.
INT svcAddrAdminStatus	1.3.6.1.4.1.277.5.1.3.1.4	INTEGER	read-write	The status of this entry.
svcAtmUserPartTable	1.3.6.1.4.1.277.5.1.4		not-accessible	A table of partial SVC addresses associated with ports on this node, relevant only to ATM DTE ports for use in ILMI address registration.
svcAtmUserPartEntry	1.3.6.1.4.1.277.5.1.4.1		not-accessible	The user part entry contains objects relevant to partial SVC addresses associated with ATM DTE ports on this node.
IND svcAtmUserPartIfIndex	1.3.6.1.4.1.277.5.1.4.1.1	Index	read-only	The interface value of the corresponding MIB-II ifEntry.
OCT svcAtmUserPartUserPart	1.3.6.1.4.1.277.5.1.4.1.2	OCTET STRING	read-only	A partial ATM endsystem address associated with this ATM DTE port. It will be combined with ATM endsystem prefixes received from the peer DCE to form a full ATM endsystem address. This object is coded as 7 binary octets.
INT svcAtmUserPartAdminStatus	1.3.6.1.4.1.277.5.1.4.1.3	INTEGER	read-write	The status of this entry.
svcmgt	1.3.6.1.4.1.277.5.2
svcConfigTable	1.3.6.1.4.1.277.5.2.1		not-accessible	A table of SVC configuration paramaters associated with logical ports. The number of entries is given by the value of ifNumber in MIB-II.
svcConfigEntry	1.3.6.1.4.1.277.5.2.1.1		not-accessible	The SVC configuration entry contains objects relevant to SVC operation on a logical port.
IND svcConfigIfIndex	1.3.6.1.4.1.277.5.2.1.1.1	Index	read-only	The ifIndex value of the corresponding ifEntry.
IP svcConfigInitiateIdentStatsUpload	1.3.6.1.4.1.277.5.2.1.1.2	IpAddress	read-write	Setting this object initiates a TFTP upload of SVC identification statistics to the specified IP address. These statistics may be used to identify SVC's of interest on this port and to determine the keys for those SVC's so that further information may be obtained by accessing the circuit table.
INT svcConfigCgPtyInsertionMode	1.3.6.1.4.1.277.5.2.1.1.3	INTEGER	read-write	This object determines whether a statically configured address shall be inserted in the calling party address IE for calls entering the network at this port.
OCT svcConfigCgPtyInsertionAddress	1.3.6.1.4.1.277.5.2.1.1.4	OCTET STRING	read-write	The calling party address to use in conjunction with the calling party insertion function. E.164 addresses are coded as 15 ASCII octets, utilizing leading ASCII '0' characters, as necessary. Atm-endsystem addresses are coded as 20 octet binary addresses.
INT svcConfigCgPtyInsertionNmbPlan	1.3.6.1.4.1.277.5.2.1.1.5	INTEGER	read-write	The numbering plan corresponding to this entry's calling party insertion address object.
INT svcConfigCgPtyScreenMode	1.3.6.1.4.1.277.5.2.1.1.6	INTEGER	read-write	The type of screening to perform on the calling party number for calls entering the network at this port. Screening will be conducted by performing a bit-wise (for prefixes) or byte-wise (for addresses) comparison of the calling party number with the appropriate prefix or address database(s), as configured.
INT svcConfigEgressAddrXlateMode	1.3.6.1.4.1.277.5.2.1.1.7	INTEGER	read-write	This object determines the type of address translation, if any to occur for calls exiting the network at this port. The tunnelling mode will screen the called address against the prefixes configured for this port. If no match is found, no action is taken. If a remote gateway address is configured for the matching prefix entry, the called party address will be tunnelled as a called subaddress and the configured remote gateway address will be inserted as the called party address. If a local gateway address is configured for the matching prefix entry, the calling party address, if present, will be tunnelled as a calling subaddress and the configured local gateway address, if present, will be inserted as the calling party. The replacement mode will operate as does the tunnelling mode, except the original called and calling party addresses will be discarded. The two translation modes are used for address interworking between networks using E.164 ATM Endsystem addresses and native ISDN E.164 addresses.
INT svcConfigIngressAddrXlateMode	1.3.6.1.4.1.277.5.2.1.1.8	INTEGER	read-write	This object determines the type of address translation, if any to occur for calls entering the network at this port. The tunnelling mode reverses the actions of egress tunnelling. If a called subaddress is present, it will replace the called party address, which will be discarded. If a calling subaddress is present, it will replace the calling party address, which will be discarded. The two translation modes are used for address interworking between networks using E.164 ATM Endsystem addresses and native ISDN E.164 addresses.
INT svcConfigCgPtyPresentationMode	1.3.6.1.4.1.277.5.2.1.1.9	INTEGER	read-write	This object controls the circumstances under which the calling party number shall be presented at the egress port of the network.
svcAtmConfigTable	1.3.6.1.4.1.277.5.2.2		not-accessible	A table of ATM signalling paramaters associated with ATM logical ports. The maximum number of entries is given by the value of ifNumber in MIB-II.
svcAtmConfigEntry	1.3.6.1.4.1.277.5.2.2.1		not-accessible	The SVC ATM configuration entry contains objects relevant to the configuration and monitoring of ATM signalling on an ATM logical port.
IND svcAtmConfigIfIndex	1.3.6.1.4.1.277.5.2.2.1.1	Index	read-only	The ifIndex value of the corresponding ifEntry.
INT svcAtmConfigAdminStatus	1.3.6.1.4.1.277.5.2.2.1.2	INTEGER	read-write	The configured state of the ATM signalling function for this port.
INT svcAtmConfigOperStatus	1.3.6.1.4.1.277.5.2.2.1.3	INTEGER	read-only	The operational status of the signalling function on this port.
INT svcAtmConfigQ93bMaxRestart	1.3.6.1.4.1.277.5.2.2.1.4	INTEGER	read-write	The maximum number of unacknowledged restarts to send before declaring a signalling failure.
INT svcAtmConfigQ93bMaxStatEnq	1.3.6.1.4.1.277.5.2.2.1.5	INTEGER	read-write	The maximum number of unacknowledged status enquiries to send before issuing a restart.
INT svcAtmConfigQ93bT303	1.3.6.1.4.1.277.5.2.2.1.6	INTEGER	read-write	Protocol Timer T303, specified in milliseconds.
INT svcAtmConfigQ93bT308	1.3.6.1.4.1.277.5.2.2.1.7	INTEGER	read-write	Protocol Timer T308, specified in milliseconds.
INT svcAtmConfigQ93bT309	1.3.6.1.4.1.277.5.2.2.1.8	INTEGER	read-write	Protocol Timer T309, specified in milliseconds.
INT svcAtmConfigQ93bT310	1.3.6.1.4.1.277.5.2.2.1.9	INTEGER	read-write	Protocol Timer T310, specified in milliseconds.
INT svcAtmConfigQ93bT313	1.3.6.1.4.1.277.5.2.2.1.10	INTEGER	read-write	Protocol Timer T313, specified in milliseconds.
INT svcAtmConfigQ93bT316	1.3.6.1.4.1.277.5.2.2.1.11	INTEGER	read-write	Protocol Timer T316, specified in milliseconds.
INT svcAtmConfigQ93bT322	1.3.6.1.4.1.277.5.2.2.1.12	INTEGER	read-write	Protocol Timer T322, specified in milliseconds.
INT svcAtmConfigQ93bT398	1.3.6.1.4.1.277.5.2.2.1.13	INTEGER	read-write	Protocol Timer T398, specified in milliseconds.
INT svcAtmConfigQ93bT399	1.3.6.1.4.1.277.5.2.2.1.14	INTEGER	read-write	Protocol Timer T399, specified in milliseconds.
CTR svcAtmConfigQ93bTotalConns	1.3.6.1.4.1.277.5.2.2.1.15	Counter	read-only	The total number of SVC's established on this port.
CTR svcAtmConfigQ93bActiveConns	1.3.6.1.4.1.277.5.2.2.1.16	Counter	read-only	The number of SVC's present on this port.
INT svcAtmConfigQ93bLastCauseTx	1.3.6.1.4.1.277.5.2.2.1.17	INTEGER	read-only	The last transmitted cause code for this port.
INT svcAtmConfigQ93bLastCauseRx	1.3.6.1.4.1.277.5.2.2.1.18	INTEGER	read-only	The last received cause code for this port.
CTR svcAtmConfigQ93bNumSetupPduTx	1.3.6.1.4.1.277.5.2.2.1.19	Counter	read-only	The number of setup PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumSetupPduRx	1.3.6.1.4.1.277.5.2.2.1.20	Counter	read-only	The number of setup PDU's received on this port.
CTR svcAtmConfigQ93bNumCallProcPduTx	1.3.6.1.4.1.277.5.2.2.1.21	Counter	read-only	The number of call proceeding PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumCallProcPduRx	1.3.6.1.4.1.277.5.2.2.1.22	Counter	read-only	The number of call proceeding PDU's received on this port.
CTR svcAtmConfigQ93bNumConnectPduTx	1.3.6.1.4.1.277.5.2.2.1.23	Counter	read-only	The number of connect PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumConnectPduRx	1.3.6.1.4.1.277.5.2.2.1.24	Counter	read-only	The number of connect PDU's received on this port.
CTR svcAtmConfigQ93bNumConnectAckPduTx	1.3.6.1.4.1.277.5.2.2.1.25	Counter	read-only	The number of connect ack PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumConnectAckPduRx	1.3.6.1.4.1.277.5.2.2.1.26	Counter	read-only	The number of connect ack PDU's received on this port.
CTR svcAtmConfigQ93bNumReleasePduTx	1.3.6.1.4.1.277.5.2.2.1.27	Counter	read-only	The number of release PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumReleasePduRx	1.3.6.1.4.1.277.5.2.2.1.28	Counter	read-only	The number of release PDU's received on this port.
CTR svcAtmConfigQ93bNumReleaseCmpltPduTx	1.3.6.1.4.1.277.5.2.2.1.29	Counter	read-only	The number of release complete PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumReleaseCmpltPduRx	1.3.6.1.4.1.277.5.2.2.1.30	Counter	read-only	The number of release complete PDU's received on this port.
CTR svcAtmConfigQ93bNumAddPtyPduTx	1.3.6.1.4.1.277.5.2.2.1.31	Counter	read-only	The number of add party PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumAddPtyPduRx	1.3.6.1.4.1.277.5.2.2.1.32	Counter	read-only	The number of add party PDU's received on this port.
CTR svcAtmConfigQ93bNumAddPtyAckPduTx	1.3.6.1.4.1.277.5.2.2.1.33	Counter	read-only	The number of add party acknowledge PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumAddPtyAckPduRx	1.3.6.1.4.1.277.5.2.2.1.34	Counter	read-only	The number of add party acknowledge PDU's received on this port.
CTR svcAtmConfigQ93bNumAddPtyRejPduTx	1.3.6.1.4.1.277.5.2.2.1.35	Counter	read-only	The number of add party reject PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumAddPtyRejPduRx	1.3.6.1.4.1.277.5.2.2.1.36	Counter	read-only	The number of add party reject PDU's received on this port.
CTR svcAtmConfigQ93bNumDropPtyPduTx	1.3.6.1.4.1.277.5.2.2.1.37	Counter	read-only	The number of drop party PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumDropPtyPduRx	1.3.6.1.4.1.277.5.2.2.1.38	Counter	read-only	The number of drop party PDU's received on this port.
CTR svcAtmConfigQ93bNumDropPtyAckPduTx	1.3.6.1.4.1.277.5.2.2.1.39	Counter	read-only	The number of drop party acknowledge PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumDropPtyAckPduRx	1.3.6.1.4.1.277.5.2.2.1.40	Counter	read-only	The number of drop party acknowledge PDU's received on this port.
CTR svcAtmConfigQ93bNumStatusEnqPduTx	1.3.6.1.4.1.277.5.2.2.1.41	Counter	read-only	The number of status enquiry PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumStatusEnqPduRx	1.3.6.1.4.1.277.5.2.2.1.42	Counter	read-only	The number of status enquiry PDU's received on this port.
CTR svcAtmConfigQ93bNumStatusPduTx	1.3.6.1.4.1.277.5.2.2.1.43	Counter	read-only	The number of status PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumStatusPduRx	1.3.6.1.4.1.277.5.2.2.1.44	Counter	read-only	The number of status PDU's received on this port.
CTR svcAtmConfigQ93bNumRestartPduTx	1.3.6.1.4.1.277.5.2.2.1.45	Counter	read-only	The number of restart PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumRestartPduRx	1.3.6.1.4.1.277.5.2.2.1.46	Counter	read-only	The number of restart PDU's received on this port.
CTR svcAtmConfigQ93bNumRestartAckPduTx	1.3.6.1.4.1.277.5.2.2.1.47	Counter	read-only	The number of restart acknowledge PDU's transmitted on this port.
CTR svcAtmConfigQ93bNumRestartAckPduRx	1.3.6.1.4.1.277.5.2.2.1.48	Counter	read-only	The number of restart acknowledge PDU's received on this port.
INT svcAtmConfigQSaalMaxCC	1.3.6.1.4.1.277.5.2.2.1.49	INTEGER	read-write	The maximum number of unacknowledged transmitted control PDU's before declaring a loss of connection.
INT svcAtmConfigQSaalMaxPD	1.3.6.1.4.1.277.5.2.2.1.50	INTEGER	read-write	The maximum number of PDU's transmitted before a POLL PDU is transmitted.
INT svcAtmConfigQSaalMaxStat	1.3.6.1.4.1.277.5.2.2.1.51	INTEGER	read-write	The maximum number of list elements in a STAT PDU.
INT svcAtmConfigQSaalTPoll	1.3.6.1.4.1.277.5.2.2.1.52	INTEGER	read-write	The protocol timer corresponding to the polling function, specified in milliseconds.
INT svcAtmConfigQSaalTKeepalive	1.3.6.1.4.1.277.5.2.2.1.53	INTEGER	read-write	The protocol timer corresponding to the keepalive function, specified in milliseconds.
INT svcAtmConfigQSaalTNoResponse	1.3.6.1.4.1.277.5.2.2.1.54	INTEGER	read-write	The protocol timer corresponding to the response timeout function, specified in milliseconds.
INT svcAtmConfigQSaalTCC	1.3.6.1.4.1.277.5.2.2.1.55	INTEGER	read-write	The protocol timer corresponding to the transmission of control PDU's, specified in milliseconds.
INT svcAtmConfigQSaalTIdle	1.3.6.1.4.1.277.5.2.2.1.56	INTEGER	read-write	The protocol timer corresponding to the idle function for UNI 3.1, only, specified in milliseconds.
CTR svcAtmConfigQSaalNumDiscardTx	1.3.6.1.4.1.277.5.2.2.1.57	Counter	read-only	The number of QSaal transmit discards on this port.
CTR svcAtmConfigQSaalNumDiscardRx	1.3.6.1.4.1.277.5.2.2.1.58	Counter	read-only	The number of QSaal receive discards on this port.
CTR svcAtmConfigQSaalNumErrorTx	1.3.6.1.4.1.277.5.2.2.1.59	Counter	read-only	The number of QSaal transmit errors on this port.
CTR svcAtmConfigQSaalNumErrorRx	1.3.6.1.4.1.277.5.2.2.1.60	Counter	read-only	The number of QSaal receive errors on this port.
CTR svcAtmConfigQSaalNumBgnPduTx	1.3.6.1.4.1.277.5.2.2.1.61	Counter	read-only	The number of begin PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumBgnPduRx	1.3.6.1.4.1.277.5.2.2.1.62	Counter	read-only	The number of begin PDU's received on this port.
CTR svcAtmConfigQSaalNumBgakPduTx	1.3.6.1.4.1.277.5.2.2.1.63	Counter	read-only	The number of begin acknowledge PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumBgakPduRx	1.3.6.1.4.1.277.5.2.2.1.64	Counter	read-only	The number of begin acknowledge PDU's received on this port.
CTR svcAtmConfigQSaalNumBgrejPduTx	1.3.6.1.4.1.277.5.2.2.1.65	Counter	read-only	The number of begin reject PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumBgrejPduRx	1.3.6.1.4.1.277.5.2.2.1.66	Counter	read-only	The number of begin reject PDU's received on this port.
CTR svcAtmConfigQSaalNumEndPduTx	1.3.6.1.4.1.277.5.2.2.1.67	Counter	read-only	The number of end PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumEndPduRx	1.3.6.1.4.1.277.5.2.2.1.68	Counter	read-only	The number of end PDU's received on this port.
CTR svcAtmConfigQSaalNumEndakPduTx	1.3.6.1.4.1.277.5.2.2.1.69	Counter	read-only	The number of end acknowledge PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumEndakPduRx	1.3.6.1.4.1.277.5.2.2.1.70	Counter	read-only	The number of end acknowldge PDU's received on this port.
CTR svcAtmConfigQSaalNumRsPduTx	1.3.6.1.4.1.277.5.2.2.1.71	Counter	read-only	The number of resynchronization PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumRsPduRx	1.3.6.1.4.1.277.5.2.2.1.72	Counter	read-only	The number of resynchronization PDU's received on this port.
CTR svcAtmConfigQSaalNumRsakPduTx	1.3.6.1.4.1.277.5.2.2.1.73	Counter	read-only	The number of resynchronization acknowledge PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumRsakPduRx	1.3.6.1.4.1.277.5.2.2.1.74	Counter	read-only	The number of resynchronization acknowldge PDU's received on this port.
CTR svcAtmConfigQSaalNumErPduTx	1.3.6.1.4.1.277.5.2.2.1.75	Counter	read-only	The number of error recovery PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumErPduRx	1.3.6.1.4.1.277.5.2.2.1.76	Counter	read-only	The number of errror recovery PDU's received on this port.
CTR svcAtmConfigQSaalNumErakPduTx	1.3.6.1.4.1.277.5.2.2.1.77	Counter	read-only	The number of error recovery acknowledge PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumErakPduRx	1.3.6.1.4.1.277.5.2.2.1.78	Counter	read-only	The number of errror recovery acknowledge PDU's received on this port.
CTR svcAtmConfigQSaalNumSdPduTx	1.3.6.1.4.1.277.5.2.2.1.79	Counter	read-only	The number of sequenced data PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumSdPduRx	1.3.6.1.4.1.277.5.2.2.1.80	Counter	read-only	The number of sequenced data PDU's received on this port.
CTR svcAtmConfigQSaalNumPollPduTx	1.3.6.1.4.1.277.5.2.2.1.81	Counter	read-only	The number of poll PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumPollPduRx	1.3.6.1.4.1.277.5.2.2.1.82	Counter	read-only	The number of poll PDU's received on this port.
CTR svcAtmConfigQSaalNumStatPduTx	1.3.6.1.4.1.277.5.2.2.1.83	Counter	read-only	The number of status PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumStatPduRx	1.3.6.1.4.1.277.5.2.2.1.84	Counter	read-only	The number of status PDU's received on this port.
CTR svcAtmConfigQSaalNumUstatPduTx	1.3.6.1.4.1.277.5.2.2.1.85	Counter	read-only	The number of unsolicited status PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumUstatPduRx	1.3.6.1.4.1.277.5.2.2.1.86	Counter	read-only	The number of unsolicited status PDU's received on this port.
CTR svcAtmConfigQSaalNumUdPduTx	1.3.6.1.4.1.277.5.2.2.1.87	Counter	read-only	The number of unnumbered user data PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumUdPduRx	1.3.6.1.4.1.277.5.2.2.1.88	Counter	read-only	The number of unnumbered user data PDU's received on this port.
CTR svcAtmConfigQSaalNumMdPduTx	1.3.6.1.4.1.277.5.2.2.1.89	Counter	read-only	The number of unnumbered management data PDU's transmitted on this port.
CTR svcAtmConfigQSaalNumMdPduRx	1.3.6.1.4.1.277.5.2.2.1.90	Counter	read-only	The number of unnumbered management data PDU's received on this port.
svcAtmFailedCallTable	1.3.6.1.4.1.277.5.2.3		not-accessible	A table of objects describing the N most recent SVC failures per port, in FIFO order.
svcAtmFailedCallEntry	1.3.6.1.4.1.277.5.2.3.1		not-accessible	The failed call entry contains objects relevant to abnormal SVC call failures.
IND svcAtmFailedCallIfIndex	1.3.6.1.4.1.277.5.2.3.1.1	Index	read-only	The interface value of the corresponding MIB-II ifEntry for the port at which this call failure was declared.
INT svcAtmFailedCallIndex	1.3.6.1.4.1.277.5.2.3.1.2	INTEGER	read-only	The instance number for this failed call at this port.
INT svcAtmFailedCallDirection	1.3.6.1.4.1.277.5.2.3.1.3	INTEGER	read-only	The direction of the failed call.
INT svcAtmFailedCallPduType	1.3.6.1.4.1.277.5.2.3.1.4	INTEGER	read-only	The Pdu Type containing the cause IE.
INT svcAtmFailedCallPduDirection	1.3.6.1.4.1.277.5.2.3.1.5	INTEGER	read-only	Whether the terminating PDU was transmitted or received on this port.
INT svcAtmFailedCallCause	1.3.6.1.4.1.277.5.2.3.1.6	INTEGER	read-only	The failure cause contained in the cause IE.
INT svcAtmFailedCallLocation	1.3.6.1.4.1.277.5.2.3.1.7	INTEGER	read-only	The failure location contained in the cause IE.
OCT svcAtmFailedCallDiagnostic	1.3.6.1.4.1.277.5.2.3.1.8	OCTET STRING	read-only	The diagnostic information contained in the cause IE.
TIK svcAtmFailedCallCreationTime	1.3.6.1.4.1.277.5.2.3.1.9	TimeTicks	read-only	The sysUpTime when this call was initiated.
TIK svcAtmFailedCallTerminationTime	1.3.6.1.4.1.277.5.2.3.1.10	TimeTicks	read-only	The sysUpTime when this call was terminated.
INT svcAtmFailedCallFailureNodeId	1.3.6.1.4.1.277.5.2.3.1.11	INTEGER	read-only	The node which caused the SVC failure.
IND svcAtmFailedCallFailureIfIndex	1.3.6.1.4.1.277.5.2.3.1.12	Index	read-only	The port on the failure node which caused the SVC failure.
OCT svcAtmFailedCallCallingParty	1.3.6.1.4.1.277.5.2.3.1.13	OCTET STRING	read-only	The calling party number for this failed call, if present.
OCT svcAtmFailedCallCalledParty	1.3.6.1.4.1.277.5.2.3.1.14	OCTET STRING	read-only	The called party number for this failed call.
INT svcAtmFailedCallAtmTfdType	1.3.6.1.4.1.277.5.2.3.1.15	INTEGER	read-only	The combination of forward traffic parameters for this failed call.
INT svcAtmFailedCallAtmTfdParam1	1.3.6.1.4.1.277.5.2.3.1.16	INTEGER	read-only	Forward traffic descriptor parameter 1 for this failed call.
INT svcAtmFailedCallAtmTfdParam2	1.3.6.1.4.1.277.5.2.3.1.17	INTEGER	read-only	Forward traffic descriptor parameter 2 for this failed call.
INT svcAtmFailedCallAtmTfdParam3	1.3.6.1.4.1.277.5.2.3.1.18	INTEGER	read-only	Forward traffic descriptor parameter 3 for this failed call.
INT svcAtmFailedCallAtmQosClass	1.3.6.1.4.1.277.5.2.3.1.19	INTEGER	read-only	Forward QOS class for this failed call.
INT svcAtmFailedCallAtmRTfdType	1.3.6.1.4.1.277.5.2.3.1.20	INTEGER	read-only	The combination of reverse traffic parameters for this failed call.
INT svcAtmFailedCallAtmRTfdParam1	1.3.6.1.4.1.277.5.2.3.1.21	INTEGER	read-only	Reverse traffic descriptor parameter 1 for this failed call.
INT svcAtmFailedCallAtmRTfdParam2	1.3.6.1.4.1.277.5.2.3.1.22	INTEGER	read-only	Reverse traffic descriptor parameter 2 for this failed call.
INT svcAtmFailedCallAtmRTfdParam3	1.3.6.1.4.1.277.5.2.3.1.23	INTEGER	read-only	Reverse traffic descriptor parameter 3 for this failed call.
INT svcAtmFailedCallAtmRQoSClass	1.3.6.1.4.1.277.5.2.3.1.24	INTEGER	read-only	Reverse QOS class for this failed call.
INT svcAtmFailedCallBBearerClass	1.3.6.1.4.1.277.5.2.3.1.25	INTEGER	read-only	Broadband bearer class for this failed call.
INT svcAtmFailedCallBBearerTfcType	1.3.6.1.4.1.277.5.2.3.1.26	INTEGER	read-only	Broadband bearer traffic type for this failed call.
INT svcAtmFailedCallBBearerTmgRqmt	1.3.6.1.4.1.277.5.2.3.1.27	INTEGER	read-only	Broadband bearer timing requirement for this failed call.
INT svcAtmFailedCallBBearerUplaneCfg	1.3.6.1.4.1.277.5.2.3.1.28	INTEGER	read-only	Broadband bearer user plane configuration for this failed call.
INT svcAtmFailedCallBBearerClippingSusc	1.3.6.1.4.1.277.5.2.3.1.29	INTEGER	read-only	Broadband bearer clipping susceptability for this failed call.
INT svcAtmFailedCallAdminStatus	1.3.6.1.4.1.277.5.2.3.1.30	INTEGER	read-only	All entries are initially invalid. Due to the FIFO nature of this table, once N entries have been created, all entries will always be valid.
software	1.3.6.1.4.1.277.6
swTable	1.3.6.1.4.1.277.6.1		not-accessible	A list of swEntry's. The number of entries is given by the value of swCardNumber
swEntry	1.3.6.1.4.1.277.6.1.1		not-accessible	The software entry contains objects describing the software cards.
INT swLogicalSlotId	1.3.6.1.4.1.277.6.1.1.1	INTEGER	read-only	The logical slot number of this card. This is used as an index for the swTable. In redundant configurations, this can be the physical slot number of either redundant card. In non redundant configurations, this is the same as cardPhysicalSlotId.
INT swRedundState	1.3.6.1.4.1.277.6.1.1.2	INTEGER	read-only	The current redundancy state of this card.
STR swRevision	1.3.6.1.4.1.277.6.1.1.3	DisplayString	read-only	The software revision number in the form (major.minor.maint.patch) where major == the major release number minor == the minor release number maint == a maintenance release based on major.minor patch == a patch release based on major.minor.maint
STR swBuildID	1.3.6.1.4.1.277.6.1.1.4	DisplayString	read-only	An identifier which uniquely identifies the software image within the scope of the release. The build ID is generated automatically through the build process and assigned to the software image during the final load generation.
STR swBuildDate	1.3.6.1.4.1.277.6.1.1.5	DisplayString	read-only	The date on which the software image was generated.
STR swBuildDescription	1.3.6.1.4.1.277.6.1.1.6	DisplayString	read-only	A general description of the release.
STR swCopyrightNotice	1.3.6.1.4.1.277.6.1.1.7	DisplayString	read-only	Legalese describing the Copyrights covering this software image.
INT swCapabilityMask	1.3.6.1.4.1.277.6.1.1.8	INTEGER	read-only	A 32-bit integer which bitmaps optional or additional features supported by this software release. For use by the NMS in determining capabilities of the software. The significance of this bitmap varies by release. For Cascade internal use.
INT swFeatureMask	1.3.6.1.4.1.277.6.1.1.9	INTEGER	read-only	A 32-bit integer which bitmaps optional or additional features supported by this software release. For use by the NMS in determining capabilities of the software. The significance of this bitmap varies by release. For Cascade internal use.
INT swPatchMask	1.3.6.1.4.1.277.6.1.1.10	INTEGER	read-only	A 32-bit integer which bitmaps incremental patches which have been applied to the software release. The significance of this bitmap varies by release. For Cascade internal use.
STR swBuildUserId	1.3.6.1.4.1.277.6.1.1.11	DisplayString	read-only	The user ID of the person responsible for generating the software image. For Cascade internal use.
STR swBuildView	1.3.6.1.4.1.277.6.1.1.12	DisplayString	read-only	Source control information for image generation. For Cascade internal use.
STR swBuildConfigSpec	1.3.6.1.4.1.277.6.1.1.13	DisplayString	read-only	Source control information for image generation. For Cascade internal use.
provserver	1.3.6.1.4.1.277.9

RFC description

Manages Cascade STDX/B-STDX switch nodes, ports, circuits, and connections including ATM and ISDN interfaces.

Start monitoring Cascade Communications ATM/Frame Relay switches (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CASCADE-MIB

What Is CASCADE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description