RAD-MIB

All MIBs › RAD-MIB

Category: System Management

Description:

Manages RAD Data Communications core equipment configuration, system parameters, and operational state.

Imported Objects

atmTrafficDescrParamEntry	OBJECT-TYPE
atmVcCrossConnectEntry	OBJECT-TYPE
atmVclVci	OBJECT-TYPE
atmVclVpi	OBJECT-TYPE
atmVpCrossConnectEntry	OBJECT-TYPE
atmVplVpi	OBJECT-TYPE

From BRIDGE-MIB

BridgeId
Timeout
dot1dBasePortEntry	OBJECT-TYPE

From DISMAN-SCHEDULE-MIB

schedEntry

OBJECT-TYPE

From DOT3-OAM-MIB

dot3OamEntry	OBJECT-TYPE
dot3OamOperStatus	OBJECT-TYPE

From DS1-MIB

dsx1CurrentIndex	OBJECT-TYPE
dsx1IntervalIndex	OBJECT-TYPE
dsx1IntervalNumber	OBJECT-TYPE
dsx1LineIndex	OBJECT-TYPE
dsx1LineStatus	OBJECT-TYPE
dsx1LineStatusLastChange	OBJECT-TYPE
dsx1LoopbackStatus	OBJECT-TYPE
dsx1TotalIndex	OBJECT-TYPE

From DS3-MIB

dsx3ConfigEntry	OBJECT-TYPE
dsx3LineStatus	OBJECT-TYPE
dsx3LoopbackStatus	OBJECT-TYPE

From IANAifType-MIB

IANAifType

From IEEE8021-CFM-MIB

dot1agCfmMaIndex	OBJECT-TYPE
dot1agCfmMdIndex	OBJECT-TYPE
dot1agCfmMepDbRMepIdentifier	OBJECT-TYPE
dot1agCfmMepIdentifier	OBJECT-TYPE

From IF-MIB

InterfaceIndex
ifAlias	OBJECT-TYPE
ifDescr	OBJECT-TYPE
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From LLDP-MIB

LldpPortIdSubtype

From PerfHist-TC-MIB

PerfCurrentCount
PerfIntervalCount
PerfTotalCount

From Q-BRIDGE-MIB

PortList
VlanId
dot1qVlanStaticEntry	OBJECT-TYPE

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
IpAddress
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32
enterprises

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
RowPointer
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

What Is RAD-MIB?

RAD-MIB is the enterprise base MIB for RAD Data Communications, covering core equipment configuration, system parameters, and operational state for RAD's telecom/networking access devices, with legacy support for token ring and FDDI interfaces. This RAD-MIB MIB exposes objects for hardware/software version identification, trap generation control, configuration change tracking, and a management-station trap-notification table. It supports monitoring of device software health via agnHwVersion (hardware/firmware version reporting), agnChangeCnt (a running counter of configuration changes useful for detecting unauthorized or unexpected reconfiguration), and the trap mask/value objects that indicate which fault conditions the agent is set to report. Notable objects like agnTrapMask and mngTrapIpTable govern how the device forwards alarms to management stations, forming a dependency on the device's overall trap/notification framework. It is deployed in RAD Data Communications access, transmission, and multiplexer equipment used in carrier and enterprise WAN environments.

IPNetwork Monitor allows you to monitor SNMP objects defined in RAD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

hardware/firmware version
configuration change counter
trap mask and trap value settings
registered management-station trap destinations
trap IP address and mask per management entry

Supported Devices

RAD Data Communications access/transmission/multiplexer equipment, entire product line (base enterprise MIB)

Monitoring Examples

An operator would poll agnChangeCnt periodically to detect unexpected device reconfiguration, and check agnHwVersion to confirm firmware/hardware revision during an audit. The mngTrapIpTable (via mngEntry, mngID, mngIP, mngIPMask, mngTrapMask) would be inspected to verify which management stations are registered to receive traps and with what trap mask, revealing if a monitoring station has been dropped from the trap destination list. A jump in agnTrapValue combined with agnSpecific would indicate an active alarm condition reported by the agent.

OIDs

OID symbolic	OID numeric	Type	Access	Description
agnAccess	1.3.6.1.4.1.164.6.2.34
NTF agnActualLowRate	1.3.6.1.4.1.164.6.1.0.21			The main link is synchronized at a rate lower than expected.
NTF agnAlarmBufferClear	1.3.6.1.4.1.164.6.1.0.18			This trap indicates that alarm buffer has been cleared.
NTF agnAlarmBufferOverflow	1.3.6.1.4.1.164.6.1.0.17			This trap indicates that the quantity of alarm messages which have been written in the alarm buffer, since the last clear command, exceeds predefined threshold. (Buffer size) The new alarms are overwriting the oldest alarms (the first alarms written in the buffer). For LA-110,threshold value is 200 alarms.
I32 agnAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.2.3.3.1.2	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
agnAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.2.3.3.1		not-accessible	An entry in table.
OCT agnAlarmsCmprObj	1.3.6.1.4.1.164.3.1.2.3.3.1.3	OCTET STRING	read-only	This attribute is the compressed information itself.
agnAlarmsCmprTable	1.3.6.1.4.1.164.3.1.2.3.3		not-accessible	A table.
I32 agnAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.2.3.3.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnAlrBufCmprAlarmIdx	1.3.6.1.4.1.164.3.1.2.3.4.1.2	Integer32	read-only	A unique number to identify an entry in the history alarms buffer of the agent.
agnAlrBufCmprEntry	1.3.6.1.4.1.164.3.1.2.3.4.1		not-accessible	An entry in table.
OCT agnAlrBufCmprObj	1.3.6.1.4.1.164.3.1.2.3.4.1.3	OCTET STRING	read-only	This attribute is the compressed information itself.
agnAlrBufCmprTable	1.3.6.1.4.1.164.3.1.2.3.4		not-accessible	A table.
I32 agnAlrBufCmprVersion	1.3.6.1.4.1.164.3.1.2.3.4.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
INT agnCAgendaCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.1.1.1	INTEGER	read-only	Active or Temporary Agenda Table. Both configurations can be read but only the Temporary can be written to.
INT agnCAgendaDayCategory	1.3.6.1.4.1.164.3.1.2.5.1.1.3	INTEGER	read-write	The Category of the Day
INT agnCAgendaDayIdx	1.3.6.1.4.1.164.3.1.2.5.1.1.2	INTEGER	read-only	Day of week
agnCAgendaEntry	1.3.6.1.4.1.164.3.1.2.5.1.1		not-accessible	An entry in table.
agnCAgendaTable	1.3.6.1.4.1.164.3.1.2.5.1		not-accessible	This table devides the week days into categories needed for DB flip consideration.
I32 agnCBuMlCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.12.1.1	Integer32	not-accessible	This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.
IP agnCBuMlDefaultGateway	1.3.6.1.4.1.164.3.1.2.2.12.1.4	IpAddress	read-write	Default Gateway's IP Address.
agnCBuMlEntry	1.3.6.1.4.1.164.3.1.2.2.12.1		not-accessible	An Entry in table agnCBuMlTable
I32 agnCBuMlOamFrequency	1.3.6.1.4.1.164.3.1.2.2.12.1.6	Integer32	read-write	Time in sec. between 2 OAM packets.
I32 agnCBuMlOamTimeoutCycles	1.3.6.1.4.1.164.3.1.2.2.12.1.7	Integer32	read-write	No. of cycles the Link will send OAM packets without receiving a response from the remote Link before switching to the Backup Link.
INT agnCBuMlRole	1.3.6.1.4.1.164.3.1.2.2.12.1.2	INTEGER	not-accessible	The Role of the Link. Primary Link is the Link that should usually work. If the Primary Link fails, the data will go through the Secondary Link. If both Primary and Secondary Links fail, the data will go through the Third Link, provided it is up.
IP agnCBuMlSubnetMask	1.3.6.1.4.1.164.3.1.2.2.12.1.5	IpAddress	read-write	The Link subnet mask.
agnCBuMlTable	1.3.6.1.4.1.164.3.1.2.2.12		not-accessible	Configuration for Primary, Secondary and Third Link. These are used for Link Backup.
INT agnCBuMlType	1.3.6.1.4.1.164.3.1.2.2.12.1.3	INTEGER	read-write	The Type of the Link. For E1/T1 the Link can be Link A - e1T1a or Link B - e1T1b.
U32 agnCBuMlWaitToRestore	1.3.6.1.4.1.164.3.1.2.2.12.1.8	Unsigned32	read-write	This object defines traffic recovery time (in milliseconds) of the link after its recovery. This object is applicable only when Recovery Mode is revertive.
I32 agnCClkCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..100) being accessed and Idx 255 relates to the TmpCnfg.
agnCClkSrcEntry	1.3.6.1.4.1.164.3.1.2.2.4.1		not-accessible	An entry in table.
I32 agnCClkSrcIdx	1.3.6.1.4.1.164.3.1.2.2.4.1.2	Integer32	read-only	An index to the table. There are only two entries to this table. Index 1 points to the Master clock parameters and Index 2 points to the Fallback clock parameters
INT agnCClkSrcMode	1.3.6.1.4.1.164.3.1.2.2.4.1.3	INTEGER	read-write	The source of the nodal timing.
I32 agnCClkSrcPrt	1.3.6.1.4.1.164.3.1.2.2.4.1.5	Integer32	read-write	This entry is valid only when we are working in rxClk or adaptive mode. For an invalid entry, the return value will be '7fff'h. - For rxClk mode, the values can be: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , notApplicable (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) - For adaptive mode, the value will be the ifIndex of the selected IP Bundle.
INT agnCClkSrcSlt	1.3.6.1.4.1.164.3.1.2.2.4.1.4	INTEGER	read-write	This entry is valid only when we are working in rxClk mode. For an invalid entry, the return value will be '7fff'h.
agnCClkSrcTable	1.3.6.1.4.1.164.3.1.2.2.4		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
I32 agnCDefaultCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.6	Integer32	read-write	Setting this attribute will define the desired working configuration when no conditions of the Flip DB Table are fulfilled and no Net GO command was issued. This command will be accepted only if the Configuration number exists (agnSEntryIsValid=yes).
I32 agnCDeleteCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.5	Integer32	read-write	Setting this attribute will delete the requested DB from the NVRAM .
INT agnCFlipActive	1.3.6.1.4.1.164.3.1.2.5.3.1.3	INTEGER	read-write	Indicates if the entry is valid. In order to Add/Modify parameters of an entry this object should be Set to Yes. In order to delete an entry, this object should be Set to No.
INT agnCFlipCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.3.1.1	INTEGER	read-only	Active or Temporary Flip Decisions Table. Both configurations can be read but only the Temporary can be written to.
I32 agnCFlipDbNo	1.3.6.1.4.1.164.3.1.2.5.3.1.5	Integer32	read-write	The ID of the required DB
INT agnCFlipDbSanityCheckCmd	1.3.6.1.4.1.164.3.1.2.5.4.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and automatically be changed to off(2).
INT agnCFlipDiscardDe	1.3.6.1.4.1.164.3.1.2.5.3.1.6	INTEGER	read-write	Indicates whether the Mux should start discarding all DE. (MP3000 Only).
agnCFlipEntry	1.3.6.1.4.1.164.3.1.2.5.3.1		not-accessible	An entry in table.
I32 agnCFlipIdx	1.3.6.1.4.1.164.3.1.2.5.3.1.2	Integer32	read-only	Entry number within the table
STR agnCFlipLogicalExp	1.3.6.1.4.1.164.3.1.2.5.3.1.4	DisplayString	read-write	A logical expression composed of events numbers (which were configured in the 'AgnCFlipNetEvantsTable') and logical operators ('\|', '&', '!', '(', ')') between them. e.g - (1 & !2) \| (121 & 230)
INT agnCFlipNetEventActive	1.3.6.1.4.1.164.3.1.2.5.2.1.3	INTEGER	read-write	Indicates if the entry is valid. In order to Add/Modify parameters of an entry, this object should be set to Yes. In order to delete an entry, this object should be Set to No.
INT agnCFlipNetEventDayType	1.3.6.1.4.1.164.3.1.2.5.2.1.10	INTEGER	read-write	The time event relates to all days defined in this category in the agnCAgendaTable. Applicable only for time event
STR agnCFlipNetEventEndTime	1.3.6.1.4.1.164.3.1.2.5.2.1.12	DisplayString	read-write	The time event will be deactivated at this time. The format is hh:mm.
I32 agnCFlipNetEventIdx	1.3.6.1.4.1.164.3.1.2.5.2.1.2	Integer32	read-only	Entry within the table
I32 agnCFlipNetEventISD	1.3.6.1.4.1.164.3.1.2.5.2.1.8	Integer32	read-write	The time in seconds since the Net Event was reported as ON until it is considered as ON. Not relevant for time events.
I32 agnCFlipNetEventNo	1.3.6.1.4.1.164.3.1.2.5.2.1.5	Integer32	read-write	The Net Event No. (Bit Index)
I32 agnCFlipNetEventOSD	1.3.6.1.4.1.164.3.1.2.5.2.1.9	Integer32	read-write	The time in seconds since the net event was reported as OFF until it is considered as OFF. Not relevant for time events.
I32 agnCFlipNetEventPort	1.3.6.1.4.1.164.3.1.2.5.2.1.7	Integer32	read-write	The port within the relevant slot. Valid values: - extPrt1(1)..exPrt16(16) - notApplicable(100) - inPrt1(101)..inPrt84(184)
INT agnCFlipNetEventsCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.2.1.1	INTEGER	read-only	Active or Temporary Net Events Table. Both configurations can be read but only the Temporary can be written to.
agnCFlipNetEventsEntry	1.3.6.1.4.1.164.3.1.2.5.2.1		not-accessible	An entry in table.
INT agnCFlipNetEventSlot	1.3.6.1.4.1.164.3.1.2.5.2.1.6	INTEGER	read-write	The slot to which the net event relates . Not applicable for time event
agnCFlipNetEventsTable	1.3.6.1.4.1.164.3.1.2.5.2		not-accessible	This table holds the Net Events the MUX should trace
STR agnCFlipNetEventStartTime	1.3.6.1.4.1.164.3.1.2.5.2.1.11	DisplayString	read-write	The time event will be activated at this time. The format is hh:mm.
INT agnCFlipNetEventType	1.3.6.1.4.1.164.3.1.2.5.2.1.4	INTEGER	read-write	The Net Event type
agnCFlipTable	1.3.6.1.4.1.164.3.1.2.5.3		not-accessible	The DB Flip Decisions Table
C32 agnChangeCnt	1.3.6.1.4.1.164.6.2.4	Counter32	read-only	The number of changes in system configuration that were reported to the manager since last cold start
G32 agnClkCurrentBufferUnderflow	1.3.6.1.4.1.164.6.2.52.3.1.1.5	Gauge32	read-only	The counter associated with the number of times Underflow event encountered by a Bridge Port in the current 15 minute interval.
agnClkCurrentEntry	1.3.6.1.4.1.164.6.2.52.3.1.1		not-accessible	An entry in the Clock Current table.
U32 agnClkCurrentIndex	1.3.6.1.4.1.164.6.2.52.3.1.1.1	Unsigned32	not-accessible	An Index that is uniquely represents the Clock.
G32 agnClkCurrentLostPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.3	Gauge32	read-only	The counter associated with the number of Lost Packets, encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkCurrentOutOfOrderPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.4	Gauge32	read-only	The counter associated with the number of times Out-of-Order Packets encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkCurrentRxPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.2	Gauge32	read-only	The counter associated with the number of Received Packets, encountered by a Bridge Port in the current 15 minute interval.
agnClkCurrentTable	1.3.6.1.4.1.164.6.2.52.3.1		not-accessible	The Clock Current table.
G32 agnClkIntervalBufferUnderflow	1.3.6.1.4.1.164.6.2.52.3.2.1.6	Gauge32	read-only	The counter associated with the number of times Underflow event is detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
agnClkIntervalEntry	1.3.6.1.4.1.164.6.2.52.3.2.1		not-accessible	An entry in the Clock Interval table.
U32 agnClkIntervalIndex	1.3.6.1.4.1.164.6.2.52.3.2.1.1	Unsigned32	not-accessible	An Index that is uniquely represents the Clock.
G32 agnClkIntervalLostPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.4	Gauge32	read-only	The counter associated with the number of Lost Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
U32 agnClkIntervalNumber	1.3.6.1.4.1.164.6.2.52.3.2.1.2	Unsigned32	not-accessible	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
G32 agnClkIntervalOutOfOrderPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.5	Gauge32	read-only	The counter associated with the number of times Out-of-Order Packets are detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 agnClkIntervalRxPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.3	Gauge32	read-only	The counter associated with the number of Received Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
agnClkIntervalTable	1.3.6.1.4.1.164.6.2.52.3.2		not-accessible	The Clock Interval table.
NTF agnClkSrcFrequencyAlarmTrap	1.3.6.1.4.1.164.6.1.0.31			The trap is sent upon Recovered Clock Frequency alarm.
I32 agnClkSrcPort	1.3.6.1.4.1.164.6.2.52.1.1.4	Integer32	read-create	This object indicates the Port/Interface Index of the port that is to be used as Clock Source. In case of Recovered Clock - it indicates the PW number.
INT agnClkSrcPortAdminStatus	1.3.6.1.4.1.164.6.2.52.1.1.6	INTEGER	read-create	This object indicates the Recovered Clock Administrative Status.
I32 agnClkSrcPortCnfgIdx	1.3.6.1.4.1.164.6.2.52.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. For product supporting a single configuration, the value will be 1.
agnClkSrcPortEntry	1.3.6.1.4.1.164.6.2.52.1.1		not-accessible	An entry in the table.
I32 agnClkSrcPortIdx	1.3.6.1.4.1.164.6.2.52.1.1.3	Integer32	not-accessible	This object indicates the running Idx of the port that is to be used as Clock Source, for each agnClkSrcPortSrcIdx instance. In case of Recovered Clock - it indicates the Clock ID.
INT agnClkSrcPortNetType	1.3.6.1.4.1.164.6.2.52.1.1.9	INTEGER	read-create	This object is relevant only in case of Recovery Clock. It indicates the Clock Network Type, i.e. the PSN network characteristics and behavior.
INT agnClkSrcPortQuality	1.3.6.1.4.1.164.6.2.52.1.1.8	INTEGER	read-create	This object indicates the Clock Source Quality.
ROW agnClkSrcPortRowStatus	1.3.6.1.4.1.164.6.2.52.1.1.5	RowStatus	read-create	This object enables Creation/ Deletion of rows in the table.
INT agnClkSrcPortSrcIdx	1.3.6.1.4.1.164.6.2.52.1.1.2	INTEGER	not-accessible	Clock Source Index. master - refers to Master clock fallback - refers to Fallback clock recovered - refers to Recovered clock.
INT agnClkSrcPortState	1.3.6.1.4.1.164.6.2.52.1.1.10	INTEGER	read-only	This object indicates the Clock State. freeRun(1) - Clock recovery is not locked to any clock. frequencyAcquisition(2) - Adaptive clock recovery is learning the frequency. rapidPhaseLock(3) - Clock recovery is in training process till it reaches fine phase lock. finePhaseLock(4) - Clock is locked and clock recovery is qualified and stable. holdover(5) - Clock recovery is in holdover mode. notApplicable(6) - Clock recovery is not applicable. .
agnClkSrcPortTable	1.3.6.1.4.1.164.6.2.52.1		not-accessible	Pool of Ports for the Master/Fallback Clock Source and of Recovered IDs. For devices with more than one configuration: Set operation is valid only to the TmpCnfg entry.
INT agnClkSrcPortType	1.3.6.1.4.1.164.6.2.52.1.1.7	INTEGER	read-create	This object is relevant only in case of Recovery Clock. It indicates the Clock Type.
NTF agnClkSrcStateChangeTrap	1.3.6.1.4.1.164.6.1.0.28			The trap is sent upon change in Recovery Clock State.
I32 agnCLoadCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.3	Integer32	read-write	This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on Valid configurations (agnSEntryIsValid)
agnClockMonitoring	1.3.6.1.4.1.164.6.2.52.3
agnClockSource	1.3.6.1.4.1.164.6.2.52
INT agnCMainExitPort	1.3.6.1.4.1.164.3.1.2.2.11	INTEGER	read-write	An object defining the Main Exit Port for the Data of the device. In the Vmux-120 Device the Data can Exit via one of the 2 existing ports: 1. Ethernet port (2) 2. A port that can be E1 or T1 or a Serial Link (3).
I32 agnCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
agnCmprEntry	1.3.6.1.4.1.164.3.1.2.3.1.1		not-accessible	An entry in table.
OCT agnCmprObj	1.3.6.1.4.1.164.3.1.2.3.1.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
agnCmprTable	1.3.6.1.4.1.164.3.1.2.3.1		not-accessible	A table.
I32 agnCmprTypIdx	1.3.6.1.4.1.164.3.1.2.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 agnCmprVersion	1.3.6.1.4.1.164.3.1.2.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnCNetDelay	1.3.6.1.4.1.164.3.1.2.5.4.6	Integer32	read-write	This attribute determines the period of time in seconds that takes for a message to be transferred over all the network. After a 'GO' command the MUX issues a delay of 'agnCNetDelay' before activating the appropriate DB. The delay will be applied only after performing agnCSaveFlipDbCmd.
INT agnCNetEventsBcast	1.3.6.1.4.1.164.3.1.2.5.4.7	INTEGER	read-write	This object determines if the Net Events will be Broadcasted to other Muxes of the Net or not. disabled - Net Events will NOT be Broadcasted enabled - Net Events will be Broadcasted. Default=disabled. The value will be applied only after performing agnCSaveFlipDbCmd.
I32 agnCNetEventsBcastInterval	1.3.6.1.4.1.164.3.1.2.5.4.8	Integer32	read-write	When agnCNetEventsBcast is enabled, this object determines the interval of time in seconds, between two consecutive Net Events transferred over the network. Default=40 sec. The interval will be applied only after performing agnCSaveFlipDbCmd.
INT agnCNetGoCmd	1.3.6.1.4.1.164.3.1.2.5.4.5	INTEGER	read-write	Setting this attribute to On will broadcast a 'GO' command to the network. When a Mux receives a 'GO' command it issues a delay for 'agnCNetDelay' seconds and then activates the DB which was pre-defined by one of the commands : 'agnCSaveNetCnfgIdxCmd' or 'agnCSaveNetFlipDbCmd'.
agnCnfgAlarm	1.3.6.1.4.1.164.3.1.2.2.8
I32 agnCnfgAlrCode	1.3.6.1.4.1.164.3.1.2.2.8.2.1.1	Integer32	read-only	The alarm code. The following attributes refer this code.
agnCnfgAlrEntry	1.3.6.1.4.1.164.3.1.2.2.8.2.1		not-accessible	An entry in table.
INT agnCnfgAlrFilter	1.3.6.1.4.1.164.3.1.2.2.8.2.1.6	INTEGER	read-write	An attribute defining if Filter is desired for the alarm . no - no filter. yes - filter activate. This filter is activated within a window of time defined by agnCnfgAlrFilterWindow. Its purpose is to avoid frequent changes of an alarm between ON/OFF states.
I32 agnCnfgAlrFilterReset	1.3.6.1.4.1.164.3.1.2.2.8.2.1.8	Integer32	read-write	This is a bottom threshold causing the alarm that does not pass it, to be declared Reset (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at most, during the window, in order to be considered OFF. This value should be less than the one of agnCnfgAlrFilterSet. Agents that do not support Alarms Filter, will return 0.
I32 agnCnfgAlrFilterSet	1.3.6.1.4.1.164.3.1.2.2.8.2.1.7	Integer32	read-write	This is a top threshold causing the alarm that passes it, to be declared Set (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at least, during the window in order to be considered ON. The maximum value will be 255. This value should be greater than the one of agnCnfgAlrFilterReset. Agents that do not support Alarms Filter, will return 0.
I32 agnCnfgAlrFilterWindow	1.3.6.1.4.1.164.3.1.2.2.8.1	Integer32	read-write	Window of time, in seconds. During this Window, the alarms filter is performed. Same Window for all agent alarms that need filtering. Upon end of the Window, the state of the alarm is updated and a new Window starts. If no alarm needs filtering, this object's value will not be used.
INT agnCnfgAlrInvert	1.3.6.1.4.1.164.3.1.2.2.8.2.1.5	INTEGER	read-write	An attribute defining the desired Invert state of an alarm . no - not inverted. yes - inverted. For MP, it is not applicable for alarms that are currently OFF.
INT agnCnfgAlrMask	1.3.6.1.4.1.164.3.1.2.2.8.2.1.4	INTEGER	read-write	An attribute defining the desired Mask state of an alarm . no - unmask (this command is not saved in agent's common database) noAndSave - unmask ; this command is saved in agent's common database yes - mask (this command is not saved in agent's common database) yesAndSave - mask ; this command is saved in agent's common database. Commands that are not saved, will be lost upon power-up or selected card removal.
I32 agnCnfgAlrPort	1.3.6.1.4.1.164.3.1.2.2.8.2.1.3	Integer32	read-only	The alarm port. The following attributes apply for the alarm code,slot and port selected. 200 = all = the attributes apply to all ports of the selected slot. When selected Slot is 'all', only 'all' or 'notApplicable' are valid Port selections. notApplicable = the selected alarm is for system or card level. =255 for MP =100 for DXC - For MP: - valid cards' ports are: exPrt1(1)..exPrt16(16) inPrt1(101)..inPrt48 (148) - IP Bundles - For DXC, the port index will include the Slot, as for all DXC tables: [(IO Slot+10)&n] ; n=odd for external ports n=even for internal ports.
agnCnfgAlrReportEntry	1.3.6.1.4.1.164.3.1.2.2.8.3.1		not-accessible	An entry in table.
agnCnfgAlrReportTable	1.3.6.1.4.1.164.3.1.2.2.8.3		not-accessible	This table enables the user to configure the desired Alarm Reports according to alarms severity.
INT agnCnfgAlrReportType	1.3.6.1.4.1.164.3.1.2.2.8.3.1.1	INTEGER	read-only	The alarm report type. trap - traps will be sent only for alarms having the selected On/Off severity or higher. buffer - only alarms having the selected On/Off severity and higher, will be reported to the buffer. relay - relay contact will be activated only for alarms having the selected On severity or higher. For products having 2 relays, this is the R1 Relay. alrLedOn/alrLedBlink - user should select a higher severity (ReportOn) for alrLedBlink than for alrLedOn (Blinking Led means a more severe alarm than steady ON Led). alrLedOn - MTCL-1 Alarm Led will be ON only when agnSAlrStatusAll equals the selected severity or higher, but lower severity than that selected for 'alrLedBlink'. For products having 2 LEDs, this is the Minor LED. alrLedBlink - MTCL-1 Alarm Led will Blink only when agnSAlrStatusAll equals the selected severity or higher. For products having 2 LEDs, this is the Major LED. relay2 - relay 2 contact will be activated only for alarms having the selected On severity or higher. This is the R2 Relay.
INT agnCnfgAlrSeverity	1.3.6.1.4.1.164.3.1.2.2.8.2.1.9	INTEGER	read-write	An attribute defining desired severity of an alarm code per slot/port
INT agnCnfgAlrSlot	1.3.6.1.4.1.164.3.1.2.2.8.2.1.2	INTEGER	read-only	The alarm slot. The following attributes apply for the alarm code and slot selected. all = the attributes apply to all slots. notApplicable = the selected alarm is for system level. For the Vmux2100 Main Board clA (3) is used.
INT agnCnfgAlrStartReportOff	1.3.6.1.4.1.164.3.1.2.2.8.3.1.3	INTEGER	read-write	This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to OFF state. notApplicable - for 'relay','alrLedOn','alrLedBlink', 'relay2' report types, in MP. noReport - no Report at all (for any severity).
INT agnCnfgAlrStartReportOn	1.3.6.1.4.1.164.3.1.2.2.8.3.1.2	INTEGER	read-write	This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to ON state. noReport - no Report at all (for any severity).
agnCnfgAlrTable	1.3.6.1.4.1.164.3.1.2.2.8.2		not-accessible	This table enables the user to set attributes to each alarm. Setting for a non-existing entry agnCnfgAlrMask, agnCnfgAlrInvert or agnCnfgAlrFilter to 'yes'(or yesAndSave for Mask) will add this new entry to the table. Setting for an existing entry agnCnfgAlrMask/ agnCnfgAlrInvert/agnCnfgAlrFilter (one or more) to 'no' (noAndSave for Mask) so that ALL these objects' values are 'no' , will delete this entry from the table. For agnCnfgAlrMask, only if [(last saved value=noAndSave) AND (new value is 'no' or 'noAndSave')] the object's value is considered 'no' for deleting the entry. For some products (like MP, MPH, Vmux2100) the Active Alarms are always part of the table and cannot be removed even if their Mask/Invert/Filter are No.
agnCnfgDataEntry	1.3.6.1.4.1.164.3.1.2.2.7.1		not-accessible	An entry in table.
agnCnfgDataTable	1.3.6.1.4.1.164.3.1.2.2.7		not-accessible	This table contains data about the agent configurations. The table will support only data about valid configurations of the agent.
STR agnCnfgDesc	1.3.6.1.4.1.164.3.1.2.2.7.1.2	DisplayString	read-write	This object is a description of the Configuration, entered by user, to enhance Cnfg recognition.
I32 agnCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.7.1.1	Integer32	read-only	This object indicates the Idx of the agent' Cnfg the following objects refer. 255=Temporary Cnfg (Set is done only to this configuration).
STR agnCnfgUpdDate	1.3.6.1.4.1.164.3.1.2.2.7.1.3	DisplayString	read-only	This object indicates the date when last update of this configuration was performed, as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. When update is performed, the agent should save the date.
IP agnCnfgUpdMnger	1.3.6.1.4.1.164.3.1.2.2.7.1.5	IpAddress	read-only	This object indicates the IP Address of the Manager who performed the last update of this configuration. When update is performed, the agent should save the IP Address of the Manager who commanded the update. That will enable a manager to know if he performed the last update, or another manager did.
STR agnCnfgUpdTime	1.3.6.1.4.1.164.3.1.2.2.7.1.4	DisplayString	read-only	This object indicates the time when last update of this configuration was performed, as it is known by the agent using its own real-time clock. When update is performed, the agent should save the time.
INT agnCOffsetCmd	1.3.6.1.4.1.164.3.1.2.2.9	INTEGER	read-write	An object defining special user request. notApplicable - is RO value for products that do not support this object. normal - nothing special u1 - user 1 - for all Voice cards, the DISPLAYED Tx and Rx Levels will have the following Offsets: - 2 Wires port: Tx Level: the base value (for 0dBm) = 0 Rx Level: the base value (for 0dBm) = -2 - 4 Wires port: Tx Level: the base value (for 0dBm) = -16 Rx Level: the base value (for 0dBm) = 7 The MIB and application DB will use the values without Offset.
NTF agnConfigDBChecksumError	1.3.6.1.4.1.164.6.1.0.16			This trap indicates that the database currently stored in the non-volatile memory of the device is corrupted
OCT agnConfigMsg	1.3.6.1.4.1.164.6.2.6	OCTET STRING	read-only	Full configuration message coded in internal RAD application format. This entry describes agent's configuration. For MP-2200 R3, this object describes agent's support of the V5.1 feature: 1 octet ; bit 0 (LSB). '1' - V5.1 feature is supported '0' - V5.1 feature is not supported.
NTF agnCounterChange	1.3.6.1.4.1.164.6.1.0.6			This notification is sent when the value of a specific Counter is changed. Agent can send as attached object the updated Counter. For details about this Counter and attached object, see spec of the relevant application.
I32 agnCQ50BlockNewModemRelayCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.5	Integer32	read-write	This object indicates the Modem Relay Calls Threshold percent (%) above which new modem calls will be rejected.
I32 agnCQ50BlockNewModemVbdCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.4	Integer32	read-write	This object indicates the Modem VBD Calls Threshold percent (%) above which new modem calls will be rejected.
I32 agnCQ50CnfgIdx	1.3.6.1.4.1.164.3.1.2.2.13.1.1	Integer32	not-accessible	This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.
I32 agnCQ50DiscardPktThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.3	Integer32	read-write	This object indicates the Bandwidth Threshold percent (%) above which voice packets will be discarded. Usually, the value selected should be higher than the value of agnCQ50StopCallsThresh.
agnCQ50Entry	1.3.6.1.4.1.164.3.1.2.2.13.1		not-accessible	An Entry in table agnCQ50Table
I32 agnCQ50StopCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.2	Integer32	read-write	This object indicates the Bandwidth Threshold percent (%) above which new Calls from the PBX will be disabled.
agnCQ50Table	1.3.6.1.4.1.164.3.1.2.2.13		not-accessible	Table for the device Q50 parameters. Q50 is a Signaling protocol used between PBX devices. It is possible to control the initiation of calls using Q.50. This is useful for devices when there is a congestion.
INT agnCSanityCheckCmd	1.3.6.1.4.1.164.3.1.2.2.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion the value will automatically be changed to off(2).
I32 agnCSaveCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.2	Integer32	read-write	This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown
INT agnCSaveFlipDbCmd	1.3.6.1.4.1.164.3.1.2.5.4.2	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and if it is OK, it will save the Flip Db in the NVRAM, activating the new Flip DB . If check detects errors, the save will not be performed. Afterwards, the object's value will change automatically to off(2).
I32 agnCSaveNetCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.5.4.3	Integer32	read-write	This attribute specifies the Id of the target NVRAM Cnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown. This attribute doesn't cause actual Flip.
INT agnCSaveNetFlipDbCmd	1.3.6.1.4.1.164.3.1.2.5.4.4	INTEGER	read-write	Setting this attribute to on(3) will save the Temp Flip DB Into the NVRAM without actual flip.
I32 agnCT1E1RingCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.10.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
INT agnCT1E1RingDualFailDetection	1.3.6.1.4.1.164.3.1.2.2.10.1.9	INTEGER	read-create	T1/E1 Ring - Dual Failure Detection enable/disable.
agnCT1E1RingEntry	1.3.6.1.4.1.164.3.1.2.2.10.1		not-accessible	An Entry in table agnCT1E1RingTable
I32 agnCT1E1RingPrimePort	1.3.6.1.4.1.164.3.1.2.2.10.1.3	Integer32	read-only	The port number in the Primary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104
INT agnCT1E1RingPrimeSlot	1.3.6.1.4.1.164.3.1.2.2.10.1.2	INTEGER	read-only	The slot number of the Primary card of the Ring Pair.
I32 agnCT1E1RingRecTime	1.3.6.1.4.1.164.3.1.2.2.10.1.6	Integer32	read-create	T1/E1 Ring Recovery Time (sec). Valid Values: 1..99, 65535. 65535=NA.
ROW agnCT1E1RingRowStatus	1.3.6.1.4.1.164.3.1.2.2.10.1.7	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table. The only possible supported RowStatus vaules are active (1) and destroy (6).
I32 agnCT1E1RingSecPort	1.3.6.1.4.1.164.3.1.2.2.10.1.5	Integer32	read-create	The port number in the Secondary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104
INT agnCT1E1RingSecSlot	1.3.6.1.4.1.164.3.1.2.2.10.1.4	INTEGER	read-create	The slot number of the Secondary card of the Ring Pair.
agnCT1E1RingTable	1.3.6.1.4.1.164.3.1.2.2.10		not-accessible	Configuration of all T1/E1 Ring ML cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that does not participate in the T1/E1 Ring, will not exist in this table. A ML port that exists in this table, cannot exist at the same time in the IO Redundancy table (sysCRdnTable).
U32 agnCT1E1RingWTR	1.3.6.1.4.1.164.3.1.2.2.10.1.8	Unsigned32	read-create	T1/E1 Ring Wait to Restore (sec). Valid Values: 0..999, 65535. 65535=NA. When the value <> 65535, the value of agnCT1E1RingRecTime must be 65535.
agnCurrClkEntry	1.3.6.1.4.1.164.6.2.52.2.1		not-accessible	An entry in the table.
INT agnCurrClkHoldover	1.3.6.1.4.1.164.6.2.52.2.1.5	INTEGER	read-only	Current Clock Holdover State. As a last resort, in the absence of higher quality timing: - a SONET/SDH object can enter 'holdover' state, until higher quality external timing becomes available again. In this state (value=yes) the SONET/SDH object uses its own timing circuits for clock of the SONET/SDH signal. - for other objects, the 'holdover'=yes state means that the object uses last available clock (stored by the object) for a pre-defined time, until another clock source is used.
INT agnCurrClkMode	1.3.6.1.4.1.164.6.2.52.2.1.2	INTEGER	read-only	Current Clock Source Mode. master - refers Master clock fallback - refers Fallback clock internal - only when both Master and Fallback Sources failed
I32 agnCurrClkObjIdx	1.3.6.1.4.1.164.6.2.52.2.1.1	Integer32	not-accessible	This MIB object identifies the object for which the Clock Source is used (System, Other System, Card).
I32 agnCurrClkPort	1.3.6.1.4.1.164.6.2.52.2.1.4	Integer32	read-only	This object indicates the Port/Interface Index of the port that is Currently used as Clock Source.
INT agnCurrClkQualification	1.3.6.1.4.1.164.6.2.52.2.1.8	INTEGER	read-only	This object indicates the Current Clock Qualification and defines whether the PLL can locked according to the stratum definitions.
INT agnCurrClkSrc	1.3.6.1.4.1.164.6.2.52.2.1.3	INTEGER	read-only	This object indicates the Current Clock Source.
INT agnCurrClkSsmBased	1.3.6.1.4.1.164.6.2.52.2.1.6	INTEGER	read-only	This parameter indicates whether clock source is selected based on receive clock quality. Clock quality is indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging).
INT agnCurrClkState	1.3.6.1.4.1.164.6.2.52.2.1.7	INTEGER	read-only	This object indicates the Current Clock State. freeRun(1) - Current clock state machine is not locked and run from the internal oscillator. rapidPhaseLock(2) - Current clock state machine is locked. finePhaseLock(3) - Current clock state machine is in pre-locking. holdover(4) - Current clock state machine is in holdover mode (due to loss of event). .
agnCurrClkTable	1.3.6.1.4.1.164.6.2.52.2		not-accessible	Current Clock Source.
OCT agnDeviceCapabilities	1.3.6.1.4.1.164.6.2.42	OCTET STRING	read-only	Indicates the optional capabilities that are implemented by this device and are manageable through this MIB. For each capability 1 BIT is allocated in each Octet starting from the LSB. If the value of the BIT = 1, the capability is Enabled. If the value of the BIT = 0, the capability is Disabled. For bit assignment, refer to device specification. Capabilities example: Router - BIT 0 (0000 0001 = 01 Hex = 1 Decimal). The 2nd octet (MSB) will represent the maximum number of intervals that the Agent can keep in its DB (same for all ports). For Vmux, this object describes agent's support of LBRAD coder feature: 1 octet ; bit 0 (LSB). '1' - LBRAD feature is supported '0' - LBRAD feature is not supported.
INT agnDeviceView	1.3.6.1.4.1.164.6.2.37	INTEGER	read-only	This variable denotes the view of the device: Look: old look, new look or new look 2. Material: Plastic or Metal.
I32 agnDlciCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.2.1.1	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 agnDlciCmprDlciIdx	1.3.6.1.4.1.164.3.1.2.3.2.1.3	Integer32	read-only	This attribute indicates a unique identifier of the Dlci, the compressed information relates to. The values are between 16 - 991.
agnDlciCmprEntry	1.3.6.1.4.1.164.3.1.2.3.2.1		not-accessible	An entry in table.
OCT agnDlciCmprObj	1.3.6.1.4.1.164.3.1.2.3.2.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
agnDlciCmprTable	1.3.6.1.4.1.164.3.1.2.3.2		not-accessible	A table.
I32 agnDlciCmprVersion	1.3.6.1.4.1.164.3.1.2.3.2.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnDlciCnfgIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
agnDlciEntry	1.3.6.1.4.1.164.3.1.2.8.1.1		not-accessible	An entry in table.
INT agnDlciFunnelEnable	1.3.6.1.4.1.164.3.1.2.8.1.1.15	INTEGER	read-create	This object selects Funnel activation: - disabled: Funnel operation will be disabled. The agnDlciTxBe and agnDlciTxBc values are not used for funneling. - enabled : Funnel operation will be enabled both for Source and Destination of the DLCI. The agnDlciTxBe and agnDlciTxBc values are used for funneling calculations. - source: Funnel operation will be enabled only for the Source of the DLCI. - destination:Funnel operation will be enabled only for the Destination of the DLCI. This object is relevant only for an encapsulating DLCI. In case of a Link Selector DLCI, the agnDlciTxBe and agnDlciTxBc values are used for bandwidth of Link Selector. Default=disabled.
I32 agnDlciHIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.7	Integer32	read-only	This attribute indicates a unique internal connection DLCI number where the Source DLCI is routed to - the Destination Side of the DLCI.
I32 agnDlciHPrtIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.6	Integer32	read-only	This attribute indicates a unique port number where the DLCI is routed to - Destination Port.
INT agnDlciHSltIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.5	INTEGER	read-only	This attribute indicates a unique slot position In the Mux where the DLCI is routed to - Destination Slot. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io16) are not valid
I32 agnDlciLIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used DLCI(16..991). This is the Source Side of the DLCI. 0=notApplicable (for voice switching) LIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
I32 agnDlciLPrtIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.3	Integer32	read-only	This attribute indicates a unique external or internal port number, including linkSelector or encapsulator. This is the Source Port of the DLCI. 100=noConnect (for voice switching) LPrtIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
INT agnDlciLSltIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. This is the Source Slot of the DLCI. vs=Voice Switching In the ?004 Unit the entries io6(10)..io16) are not valid. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) LSlotIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
I32 agnDlciPriority	1.3.6.1.4.1.164.3.1.2.8.1.1.12	Integer32	read-create	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 7 is the highest priority.
INT agnDlciRoutingProtocol	1.3.6.1.4.1.164.3.1.2.8.1.1.16	INTEGER	read-create	This object is relevant only when one side of the DLCI is a CL-NMS interface. It defines which Routing Protocol will be used for management via CL-NMS port. notApplicable will be used for all slots but CL. rip is a proprietary rip protocol. Default=rip.
ROW agnDlciRowStatus	1.3.6.1.4.1.164.3.1.2.8.1.1.17	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set agnRowStatus.255.id2.id3.id4.id5.id6.id7 = active(1). For destroying a row, the NMS should set: agnRowStatus.255.id2.id3.id4.id5.id6.id7 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
INT agnDlciRxBc	1.3.6.1.4.1.164.3.1.2.8.1.1.10	INTEGER	read-create	This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line.
INT agnDlciRxBe	1.3.6.1.4.1.164.3.1.2.8.1.1.11	INTEGER	read-create	This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line.
INT agnDlciSpoofing	1.3.6.1.4.1.164.3.1.2.8.1.1.14	INTEGER	read-create	This object refers to sending of RIP messages: - yes : RIP messages will be sent ONLY if there is a change in the Net. - no : RIP messages will be always sent. This object is relevant only when one side of the DLCI is a CL-NMS interface. Default=no.
INT agnDlciStatus	1.3.6.1.4.1.164.3.1.2.8.1.1.13	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
agnDlciTable	1.3.6.1.4.1.164.3.1.2.8.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT agnDlciTxBc	1.3.6.1.4.1.164.3.1.2.8.1.1.8	INTEGER	read-create	This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line.
INT agnDlciTxBe	1.3.6.1.4.1.164.3.1.2.8.1.1.9	INTEGER	read-create	This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line.
NTF agnDriverSwMismatch	1.3.6.1.4.1.164.6.1.0.20			There is mismatch between the SW driver and the HW of the device uplink interface.
INT agnEgressRateRange	1.3.6.1.4.1.164.6.2.47	INTEGER	read-write	This variable defines the valid ranges of egress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.
NTF agnFanFailureTrap	1.3.6.1.4.1.164.6.1.0.14			This trap is sent upon fan failure/recovery.
OCT agnFans	1.3.6.1.4.1.164.6.2.26	OCTET STRING	read-only	This entry specifies the FANs existence and status. Each fan will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each fan: 00 - FAN does not exist 01 - FAN exists and OK (Low Mode) 10 - High Mode (FAN OK) 11 - FAN exists and is Failed bits 0-1 are for first fan bits 2-3 are for 2nd fan (if exists) bits 4-5 are for 3nd fan (if exists) bits 6-7 are for 4nd fan (if exists) bits 8-9 are for 5nd fan (if exists) bits 10-11 are for 6nd fan (if exists) bits 12-13 are for 7nd fan (if exists) bits 14-15 are for 8nd fan (if exists).
agnFlipDb	1.3.6.1.4.1.164.3.1.2.5
agnFlipDbControls	1.3.6.1.4.1.164.3.1.2.5.4
INT agnFunction	1.3.6.1.4.1.164.6.2.45.1.1	INTEGER	not-accessible	This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock.
INT agnFunctionActivation	1.3.6.1.4.1.164.6.2.45.1.2	INTEGER	read-write	This MIB object indicates the activation of the current function.
agnFunctionEntry	1.3.6.1.4.1.164.6.2.45.1		not-accessible	An entry in the table.
agnFunctionTable	1.3.6.1.4.1.164.6.2.45		not-accessible	This table is used in order to activate/deactivate device functions. The index indicates the function. Each function can be Enabled or Disabled.
OCT agnGlobalAlarmMask	1.3.6.1.4.1.164.6.2.19	OCTET STRING	read-write	The value of this attribute determines the alarm traps the agent should mask and not send to the managers. Each bit from a certain octet represents a certain alarm.
U32 agnGroupCnfgIdx	1.3.6.1.4.1.164.6.2.56.1.1	Unsigned32	not-accessible	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 agnGroupComponentIdx	1.3.6.1.4.1.164.6.2.56.1.3	Unsigned32	not-accessible	This object indicates a unique Component Index that belongs to the Group defined by agnGroupIdx.
agnGroupEntry	1.3.6.1.4.1.164.6.2.56.1		not-accessible	An entry in the agnGroupTable.
U32 agnGroupIdx	1.3.6.1.4.1.164.6.2.56.1.2	Unsigned32	not-accessible	This object indicates a unique Group Index.
ROW agnGroupRowStatus	1.3.6.1.4.1.164.6.2.56.1.4	RowStatus	read-create	This object enables user to create/delete entries of this table. destroy - If a Group is used in another table, Agent may not allow destroying the entry/ies that belong to this Group Index.
agnGroupTable	1.3.6.1.4.1.164.6.2.56		not-accessible	A table that enables associating components to Group/s (or removing components of a group). The Group Idx can then be used in other tables (e.g alarmForwardingTable).
STR agnHwVersion	1.3.6.1.4.1.164.6.2.1	DisplayString	read-write	ASCII string for description and display of the agent hardware version, as it is known by the agent software.The user can update the version upon request when he changes components in the agent's module
INT agnIndication	1.3.6.1.4.1.164.6.2.8	INTEGER	read-only	Attribute describing the state of the entity the agent is responsible for. In case of a modular entity, the value of this attribute will be according to the component which is in the worst state. The order of severity (from top to bottom) is: critical-> major (or faulty)-> minor-> event-> warning-> normal (off).
INT agnIngressRateRange	1.3.6.1.4.1.164.6.2.49	INTEGER	read-write	This variable defines the valid ranges of ingress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.
OCT agnLed	1.3.6.1.4.1.164.6.2.10	OCTET STRING	read-only	This entry specifies the LEDs status of the agent module . Each led will be represented by 4 bits where the first 2 bits (left) will specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY)
agnLinkMapEntry	1.3.6.1.4.1.164.3.1.5.1.1		not-accessible	An entry in table.
agnLinkMapTable	1.3.6.1.4.1.164.3.1.5.1		not-accessible	A table.
agnListDecoding	1.3.6.1.4.1.164.3.1.2.7
INT agnListDecodingAcmRelayPrt	1.3.6.1.4.1.164.3.1.2.7.1.1.7	INTEGER	read-write	This object indicates the ACM port within the slot, desired for outbound relay (report) for the selected alarm. notApplicable - when agnListDecodingType=sanity OR when agnListDecodingAcmRelaySlt=notApplicable.
INT agnListDecodingAcmRelaySlt	1.3.6.1.4.1.164.3.1.2.7.1.1.6	INTEGER	read-write	This object indicates the ACM slot, desired for outbound relay (report) for the selected alarm. In the ?004 Unit the entries io6(10)..io12(16) are not valid. none - when agnListDecodingType=alr AND the selected alarm should not be reported by an ACM card. notApplicable - when agnListDecodingType=sanity OR when [agnListDecodingType=alr and there is no ACM card installed in the Mux].
I32 agnListDecodingCode	1.3.6.1.4.1.164.3.1.2.7.1.1.2	Integer32	read-only	The specific code for which decoding is needed.
INT agnListDecodingDefState	1.3.6.1.4.1.164.3.1.2.7.1.1.4	INTEGER	read-only	This object is applicable only for agnListDecodingType=alr. It reports the default state/severity of each alarm. User can change the severity of the alarms defined by this default via the agnListDecodingSeverity object.
STR agnListDecodingDescription	1.3.6.1.4.1.164.3.1.2.7.1.1.3	DisplayString	read-only	The description fitting the specific code and type of list required.
agnListDecodingEntry	1.3.6.1.4.1.164.3.1.2.7.1.1		not-accessible	An entry in table.
INT agnListDecodingSeverity	1.3.6.1.4.1.164.3.1.2.7.1.1.5	INTEGER	read-write	This object is applicable only for agnListDecodingType=alr. It enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code). event - can be set only for an alarm that is defined by default as 'event'. User can change the severity of the alarms defined by default as minor or major. The severity of an event may be set to another severity, but the change will actually happen only if the event threshold is active and passed the Set/ON condition. An event alarm that passed the threshold and changed its severity, will return automatically to event severity when meeting its Reset/OFF condition.
agnListDecodingTable	1.3.6.1.4.1.164.3.1.2.7.1		not-accessible	A decoding table . For each type of list, a description is given for each existing code.
INT agnListDecodingType	1.3.6.1.4.1.164.3.1.2.7.1.1.1	INTEGER	read-only	The type of list the decoding data refers to. alr - Alarms list sanity - Sanity Check Error list. counter - Counter type of ifPerfCounterType
I32 agnManagerConfigPorts	1.3.6.1.4.1.164.6.2.46	Integer32	read-write	This variable defines from which port/s this manager can manage the device. The value is a sum of 2**n, where n is a bit assigned to a certain port. For RIC-E1 and ETX 102 the value will be according to the ports combination: Network = bit 0 User= bit 1 For Example: All = 3.
I32 agnMaxNoOfConns	1.3.6.1.4.1.164.6.2.53	Integer32	read-only	This variable indicates the maximum number of connections that can be configured for the agent.
INT agnMonitorModeCmd	1.3.6.1.4.1.164.6.2.9	INTEGER	read-write	Setting this attribute to ON, will enforce the agent to change its mode of operation to Monitor Mode
agnMux	1.3.6.1.4.1.164.3.2.1
INT agnNearFarConnection	1.3.6.1.4.1.164.6.2.33	INTEGER	read-only	This parameter describes the connection between near-end and far-end agents.
INT agnNetworkInterfaceType	1.3.6.1.4.1.164.6.2.59	INTEGER	read-write	This MIB object indicates the network interface type to be used by the device. It is used for devices that use only one network port type.
I32 agnNoOfCurrentConns	1.3.6.1.4.1.164.6.2.48	Integer32	read-only	This variable indicates the number of connections currently configured for the agent.
NTF agnParametersValueChanged	1.3.6.1.4.1.164.6.1.0.19			This trap indicates that due to software upgrade, some of the parameters are assigned new values
NTF agnPowerFailureTrap	1.3.6.1.4.1.164.6.1.0.13			This trap is sent upon power failure. It is applicable for the following devices: 1. Devices having one PS unit, which sense the failure in advance, and still have time to send this trap before it goes off. 2. Devices having 2 PS units and send this trap in order to notify a failure in one of the units.
INT agnRadiusAccess	1.3.6.1.4.1.164.6.2.34.3	INTEGER	read-write	Enable/Disable authentication via RADIUS server.
agnRowPointerEntry	1.3.6.1.4.1.164.6.2.63.1		not-accessible	An entry in the table.
OID agnRowPointerIndex	1.3.6.1.4.1.164.6.2.63.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of an entry in a table.
U32 agnRowPointerNoOfUsages	1.3.6.1.4.1.164.6.2.63.1.2	Unsigned32	read-only	The number of usages of specific entry in a table, which is pointed by agnRowPointerIndex.Usually, when the value of this counter is greater than 0,the entry cannot be removed.
agnRowPointerTable	1.3.6.1.4.1.164.6.2.63		not-accessible	This table holds information about a specific entry in a table. For example, number of usages of this row.
agnSa	1.3.6.1.4.1.164.3.1.2.6
I32 agnSActiveCnfg	1.3.6.1.4.1.164.3.1.2.1.4	Integer32	read-only	This entry specifies the unique identifier of the configuration, that is currently active and running.
I32 agnSAlrCode	1.3.6.1.4.1.164.3.1.2.1.15.1.3	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at system level.
STR agnSAlrCodeDescription	1.3.6.1.4.1.164.3.1.2.1.15.1.2	DisplayString	read-only	This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
I32 agnSAlrCounter	1.3.6.1.4.1.164.3.1.2.1.15.1.6	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
agnSAlrEntry	1.3.6.1.4.1.164.3.1.2.1.15.1		not-accessible	An entry in table.
I32 agnSAlrIdx	1.3.6.1.4.1.164.3.1.2.1.15.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
INT agnSAlrInvert	1.3.6.1.4.1.164.3.1.2.1.15.1.8	INTEGER	read-only	Alarm invert : on/off.
INT agnSAlrMask	1.3.6.1.4.1.164.3.1.2.1.15.1.7	INTEGER	read-only	Alarm mask : on/off.
INT agnSAlrSeverity	1.3.6.1.4.1.164.3.1.2.1.15.1.4	INTEGER	read-only	The severity of the alarm.
INT agnSAlrState	1.3.6.1.4.1.164.3.1.2.1.15.1.5	INTEGER	read-only	State of the alarm.
INT agnSAlrStatus	1.3.6.1.4.1.164.3.1.2.1.10	INTEGER	read-only	Indicates the alarm state in the agent level, i.e. lower level (card/port) alarms not included. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSAlrStatusAll	1.3.6.1.4.1.164.3.1.2.1.11	INTEGER	read-only	Indicates the alarm state of the entire agent, i.e. including card and port alarms status. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
agnSAlrTable	1.3.6.1.4.1.164.3.1.2.1.15		not-accessible	List of agent related alarms and indications for alarms at system level.
I32 agnSaSwchStatus	1.3.6.1.4.1.164.3.1.2.6.1	Integer32	read-only	This object indicates the status of the switches on the stand-alone unit. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits: bit 0 NMS (LSB) bit 1 Terminal '1' = forces the DCE to be terminal with Rate=9600bps, Data bits=8, Stop bits=1 bit 2 Xray bit 3 SW-Load '1' = when SW is loaded bit 4 DBS Default of all bits=0 When the status of these switches is unknown, the value of this object is 255.
INT agnSClearAllAlrCmd	1.3.6.1.4.1.164.3.1.2.1.17	INTEGER	read-write	Setting this attribute to ON, enforce a clear operation on all MUX alarm events at the levels of agent, slots and ports. The clear operation will not be applied for masked/inverted alarms.
INT agnSClearAlrCmd	1.3.6.1.4.1.164.3.1.2.1.16	INTEGER	read-write	Setting this attribute to ON, enforce a clear operation on all the agent(general) events. General alarms are alarms which are not specific to a card or port. The clear operation will not be applied for masked/inverted alarms.
INT agnSClkSrc	1.3.6.1.4.1.164.3.1.2.1.9	INTEGER	read-only	This entry indicates the source of the system clock.
I32 agnSCmprErrIdx	1.3.6.1.4.1.164.3.1.2.3.5.1.2	Integer32	read-only	Unique number to identify an entry in the errors list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'.
agnSCmprErrListEntry	1.3.6.1.4.1.164.3.1.2.3.5.1		not-accessible	An entry in table.
agnSCmprErrListTable	1.3.6.1.4.1.164.3.1.2.3.5		not-accessible	A table.
OCT agnSCmprErrObj	1.3.6.1.4.1.164.3.1.2.3.5.1.3	OCTET STRING	read-only	This attribute is a full text description of the error, including: error code, slot and port numbers related to the code .
I32 agnSCmprErrVersion	1.3.6.1.4.1.164.3.1.2.3.5.1.1	Integer32	read-only	The version of the compressed data
agnSCnfgEntry	1.3.6.1.4.1.164.3.1.2.1.22.1		not-accessible	An entry in table.
agnSCnfgTable	1.3.6.1.4.1.164.3.1.2.1.22		not-accessible	This table contains an entry per configuration. It indicates if the configuration is valid.
STR agnSDateCmd	1.3.6.1.4.1.164.3.1.2.1.2	DisplayString	read-write	This entry indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent.
INT agnSDateFormat	1.3.6.1.4.1.164.3.1.2.1.1	INTEGER	read-write	This entry indicates the date and time format used for the agnSDateAndTimeCmd and for the alarm history report.
INT agnSEditBy	1.3.6.1.4.1.164.3.1.2.1.8	INTEGER	read-only	This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after an update(load) operation.
I32 agnSEditCnfg	1.3.6.1.4.1.164.3.1.2.1.5	Integer32	read-only	This entry indicates the unique identifier of the configuration that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process.
NTF agnSelfTestResultChangeTrap	1.3.6.1.4.1.164.6.1.0.29			The trap is sent upon each change in the result of a Self State operation.
I32 agnSendTrapParameter	1.3.6.1.4.1.164.6.2.27	Integer32	read-write	This object specifies if the agent will attach a specific parameter to a trap. For ACE2002 the agent will attach or not the openViewSeverity parameter according to the value of this parameter: 1 - will attach openViewSeverity. 0 - will not attach openViewSeverity.
OCT agnSensorsStatus	1.3.6.1.4.1.164.6.2.28	OCTET STRING	read-only	This entry specifies the Sensors (Temperature sensors or others) existence and status. Each sensor will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each sensor: 00 - sensor does not exist 01 - sensor exists and status is OK 11 - sensor exists and status is not OK ( e.g. temperature exceeds pre-defined threshold) bits 0-1 are for first sensor bits 2-3 are for 2nd sensor (if exists) and so on... Bit 0 is the LSB.
I32 agnSEntryIdx	1.3.6.1.4.1.164.3.1.2.1.22.1.1	Integer32	read-only	Unique number to identify an entry in the configuration table.
INT agnSEntryIsValid	1.3.6.1.4.1.164.3.1.2.1.22.1.2	INTEGER	read-only	This attribute indicates whether the specific configuration is valid in the MUX . Value of NO indicates: no such configuration in the MUX.
STR agnSErrDescription	1.3.6.1.4.1.164.3.1.2.1.20.1.2	DisplayString	read-only	This attribute is a full text description of the sanity check error including error code, slot and port numbers related to the code .
I32 agnSErrIdx	1.3.6.1.4.1.164.3.1.2.1.20.1.1	Integer32	read-only	Unique number to identify an entry in the error list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'.
agnSErrListEntry	1.3.6.1.4.1.164.3.1.2.1.20.1		not-accessible	An entry in table.
agnSErrListTable	1.3.6.1.4.1.164.3.1.2.1.20		not-accessible	List of errors and warnings found during Sanity Check process.
I32 agnSigProfCnfgIdx	1.3.6.1.4.1.164.3.1.2.10.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
agnSigProfEntry	1.3.6.1.4.1.164.3.1.2.10.2.1		not-accessible	An entry in table.
I32 agnSigProfIdx	1.3.6.1.4.1.164.3.1.2.10.2.1.2	Integer32	read-only	This attribute indicates the Signaling Profile (1..5).
agnSigProfile	1.3.6.1.4.1.164.3.1.2.10
OCT agnSigProfileABCD	1.3.6.1.4.1.164.3.1.2.10.1.1.4	OCTET STRING	read-write	For MP-2100/MP-2200 and for MP-104/204 from R2: This object represents 6 parameters, by 3 Octets : Busy Code-MSB nibble, - applicable only for Rx translation Idle Code- nibble, - applicable only for Rx translation D Bit Code- nibble, C Bit Code- nibble, B Bit Code- nibble, A Bit Code-LSB nibble. Each of Busy and Idle Code nibble will have the valid values: 0000 .. FFFF. Each of A,B,C,D Bit Code nibble represents: 0 hex = 0000 = 0 1 hex = 0001 = 1 2 hex = 0010 = A bit 3 hex = 0011 = B bit 4 hex = 0100 = C bit 5 hex = 0101 = D bit 6 hex = 0110 = A bit inverse 7 hex = 0111 = B bit inverse 8 hex = 1000 = C bit inverse 9 hex = 1001 = D bit inverse A-F hex - not used (invalid values) For MP-104/204 R1: This object represents 3 parameters, by 2 Octets : Bit 1 = Bit A - OFF Hook for Tx ; Ring for Rx (LSB) Bit 2 = Bit B - OFF Hook for Tx ; Ring for Rx Bit 3 = Bit C - OFF Hook for Tx ; Ring for Rx Bit 4 = Bit D - OFF Hook for Tx ; Ring for Rx Bit 5 = Bit A - ON Hook for Tx ; Idle for Rx Bit 6 = Bit B - ON Hook for Tx ; Idle for Rx Bit 7 = Bit C - ON Hook for Tx ; Idle for Rx Bit 8 = Bit D - ON Hook for Tx ; Idle for Rx Bit 9 = Bit A - OOS State for both Tx and Rx Bit 10 = Bit B - OOS State for both Tx and Rx Bit 11 = Bit C - OOS State for both Tx and Rx Bit 12 = Bit D - OOS State for both Tx and Rx Bit 13 = Spare (always 0) Bit 14 = Spare (always 0) Bit 15 = Spare (always 0) Bit 16 = Spare (always 0) (MSB) When the object is not applicable, the Octet String will have 0 bytes.
I32 agnSigProfileCnfgIdx	1.3.6.1.4.1.164.3.1.2.10.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. For products supporting more than one configuration,the write operation is valid only to the TmpCnfg. For Gmux2000 the range limitation (1..255) was discarded since the Idx is computed as: x 1000 + 255.
agnSigProfileEntry	1.3.6.1.4.1.164.3.1.2.10.1.1		not-accessible	An entry in table.
I32 agnSigProfileIdx	1.3.6.1.4.1.164.3.1.2.10.1.1.2	Integer32	read-only	This attribute indicates the Signaling Profile (1..5). For MP-104/204, only Profile=1 will exist.
INT agnSigProfileRxTx	1.3.6.1.4.1.164.3.1.2.10.1.1.3	INTEGER	read-only	This attribute indicates if the following objects refer to: Rx or Tx translation. Rx : ML->IO Tx : IO->ML . For MP-104/204, that means: Rx : Signaling to FXS CH Tx : Signaling to E1 Link.
agnSigProfileTable	1.3.6.1.4.1.164.3.1.2.10.1		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to agnSigProfileCnfgIdx=1. The table includes signaling profile parameters for Legacy Profiles.
STR agnSigProfName	1.3.6.1.4.1.164.3.1.2.10.2.1.3	DisplayString	read-write	Profile Name given by user.
agnSigProfTable	1.3.6.1.4.1.164.3.1.2.10.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. This is the general table of signaling profiles.
INT agnSigProfType	1.3.6.1.4.1.164.3.1.2.10.2.1.4	INTEGER	read-write	Profile Type. legacy - usual signaling. The parameters for the Legacy Profiles are detailed in the agnSigProfileTable, above. r2Cas - R2 signaling. The parameters for the R2 Profiles are detailed in the r2 ProfileCnfg tables (belong to r2If).
STR agnSLastCnfgFlipCause	1.3.6.1.4.1.164.3.1.2.1.7	DisplayString	read-only	This entry describes the flip's cause.
STR agnSLastCnfgFlipTime	1.3.6.1.4.1.164.3.1.2.1.6	DisplayString	read-only	This entry indicates the Date & Time of the last flip to the current configuration at the agent.
INT agnSMaskedAlrStat	1.3.6.1.4.1.164.3.1.2.1.12	INTEGER	read-only	Indicates the alarm state in the agent level,[ i.e. lower level (card/port) alarms not included] including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSMaskedAlrStatAll	1.3.6.1.4.1.164.3.1.2.1.13	INTEGER	read-only	Indicates the alarm state of the entire agent, i.e. including card and port alarms status,including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
I32 agnSMaxNoOfCnfg	1.3.6.1.4.1.164.3.1.2.1.21	Integer32	read-only	Maximum number of configurations that can be defined and stored in the MUX. If the mux has a large capacity, the maximum will be limited to 254.
I32 agnSNoOfSanityCheckErr	1.3.6.1.4.1.164.3.1.2.1.19	Integer32	read-only	This entry indicates the number of errors/warnings discovered by the last SanityCheck process.
OID agnSpecific	1.3.6.1.4.1.164.6.2.5	OBJECT IDENTIFIER	read-only	Object identifier of entity containing additional information regarding this instance.
INT agnSSanityCheckStatus	1.3.6.1.4.1.164.3.1.2.1.18	INTEGER	read-only	Upon completion of the Sanity check process on the TmpCnfg this attribute will be set to: FAIL(2) - when there is at least one error encountered and possibly some warnings. WARNING(3) - when there are only warnings. otherwise, the value will be OK(4). The value will be UNKNOWN(1) if changes were made in the TmpCnfg following the last Sanity check.
INT agnSshAccess	1.3.6.1.4.1.164.6.2.34.4	INTEGER	read-write	Enable/Disable accessing the device via SSH. disable - no one will be allowed to access the device via SSH. enable - all users are allowed SSH Access. managersOnly - Only manager stations listed in the manager's list are allowed.
NTF agnStationClkFailureTrap	1.3.6.1.4.1.164.6.1.0.23			This trap is sent upon Station Clock failure.
INT agnStationClockCard	1.3.6.1.4.1.164.6.2.29	INTEGER	read-only	This entry specifies the station clock card existence and status. notExist - station clock card (piggy) does not exist. notValid - station clock card exists but clock status is not valid. ok - station clock card exists, and its status is OK When the sepcific reason for clock status not being valid is known, it may be reported by lossOfSync or lossOfSignal values.
I32 agnStatNoOfUploadedIntervals	1.3.6.1.4.1.164.6.2.57	Integer32	read-only	This parameter indicates the Number of Intervals that were successfully collected and uploaded in the last statistics collection session.
NTF agnStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.2			This trap is sent whenever the state of the entity the agent is responsible for changed. TDM devices will send agnTestStatus variable to indicate the current test status.
STR agnSTimeCmd	1.3.6.1.4.1.164.3.1.2.1.3	DisplayString	read-write	This entry indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent.
INT agnStoreCmd	1.3.6.1.4.1.164.6.2.44	INTEGER	read-write	Store command. inFlash(3) = store the current Agent configuration in Flash memory. asDefConfigFile(4) = store the current Agent configuration as Default Configuration file (e.g. 'DefConfig.cfg'). Agent will perform the required command and change automatically the value of this object to off(2).
agnStringToIndexEntry	1.3.6.1.4.1.164.6.2.62.1		not-accessible	An entry in the table.
agnStringToIndexTable	1.3.6.1.4.1.164.6.2.62		not-accessible	This table holds the conversions of tables from unique String to numeric index.
OID agnStringToIndexTableId	1.3.6.1.4.1.164.6.2.62.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of the Table, having as index numeric values. In this table, the value of agnStringToIndexUserName is an attribute.
U32 agnStringToIndexTableIndex	1.3.6.1.4.1.164.6.2.62.1.3	Unsigned32	read-only	The numeric Index of agnStringToIndexTableId.
STR agnStringToIndexUserName	1.3.6.1.4.1.164.6.2.62.1.2	SnmpAdminString	not-accessible	This object indicates a unique name used by agnStringToIndexTableId, although it is not it's index.
INT agnSTstStatAll	1.3.6.1.4.1.164.3.1.2.1.14	INTEGER	read-only	on(3) - when there is at least one test in progress in one of the agent cards, otherwise the value will be off(2).
INT agnSwVersionSwapCmd	1.3.6.1.4.1.164.6.2.51	INTEGER	read-write	SW switch command. mainAndBackup (3) = Swap between Main SW and the backup one. Agent will perform the required command and change automatically the value of this object to off(2).
agnSyslog	1.3.6.1.4.1.164.6.2.58
U32 agnSyslogDeviceUdpPort	1.3.6.1.4.1.164.6.2.58.1	Unsigned32	read-write	The UDP Port of the device, from which Syslog messages are sent. Default=514.
INT agnSyslogFacility	1.3.6.1.4.1.164.6.2.58.2	INTEGER	read-write	A user defined SW module, task or function, from which Syslog messages are sent to the remote Server.
INT agnSyslogSeverityLevel	1.3.6.1.4.1.164.6.2.58.3	INTEGER	read-write	Device will send events equal or exceeding this severity level (configured by user).
agnSystemDlci	1.3.6.1.4.1.164.3.1.2.8
NTF agnSystemParameterChangeTrap	1.3.6.1.4.1.164.6.1.0.15			This trap is sent upon any change of the systemParameter value.
agnSystemTs	1.3.6.1.4.1.164.3.1.2.11
agnt	1.3.6.1.4.1.164.6.2
INT agnTelnetAccess	1.3.6.1.4.1.164.6.2.34.1	INTEGER	read-write	Enable/Disable accessing the device via Telnet. disable - no one will be allowed to access the device via Telnet. enable - all users are allowed Telnet Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSH) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSH).
INT agnTestStatus	1.3.6.1.4.1.164.6.2.22	INTEGER	read-only	Indicates the current test status (for all levels: system, card, port). This attribute will be set to: on(3): when there is at least one test in progress on the system/card/port off(2): when there is NO test in progress on the system/card/port
U32 agnTrapDelay	1.3.6.1.4.1.164.6.2.60	Unsigned32	read-write	This variable enables the user to set a delay (in seconds) before a trap is sent. This delay will be used only for traps that need to be sent during device initialization. It is needed because the device connected to our device starts transmitting traps later. The delay starts from the end of the Boot process. The device will keep the init traps in the correct order, and cancel those which clear former ones in the list. After this init delay, traps will be sent without a delay.
I32 agnTrapMask	1.3.6.1.4.1.164.6.2.2	Integer32	read-write	The value of this attribute determines the type of traps the agent should mask and not send to the management console. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
OCT agnTrapValue	1.3.6.1.4.1.164.6.2.3	OCTET STRING	read-only	The value of the trap decoded in internal RAD format. Full description is given in the Trap definition file
I32 agnTsCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.2	Integer32	read-only	This object indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration.
OCT agnTsCmprData	1.3.6.1.4.1.164.3.1.2.3.6.1.6	OCTET STRING	read-write	This object is the compressed information itself. It provides information about all TSs of a port.
agnTsCmprEntry	1.3.6.1.4.1.164.3.1.2.3.6.1		not-accessible	An entry in table.
I32 agnTsCmprPduIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.5	Integer32	read-only	This object indicates the PDU index within the same port. That provides for the case when one PDU is not sufficient for all TS Assignment data of the same port.
I32 agnTsCmprPortIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.4	Integer32	read-only	This object indicates the Port within the Slot, to which the Compressed information is related. For Port Index see each product's spec.
I32 agnTsCmprSlotIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.3	Integer32	read-only	This object indicates the Slot to which the Compressed information is related. For MP-2100: IO-1..IO-12 = (5).. (16) For DXC-30 : IO-1..IO-15 = (5).. (19). NA=255.
agnTsCmprTable	1.3.6.1.4.1.164.3.1.2.3.6		not-accessible	A table.
I32 agnTsCmprVerIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.1	Integer32	read-only	This object indicates the version of the internal format of the Compressed data.
NTF agnUploadDataTrap	1.3.6.1.4.1.164.6.1.0.11			This trap is sent upon an upload data session termination. For more details see product specification.
INT agnVoiceSwConfDialPlan	1.3.6.1.4.1.164.3.1.2.9.1.1.7	INTEGER	read-write	This is the Dialing Plan method that will be used in the Voice Switching. Static Dialing Plan - Routing is defined by the current device Zone and Node ID in the Network. Static Dialing Plan Plus - Includes the Static Dialing Plan but contains an addition of defining the number of dialed digits. Flexible Dialing Plan - Routing is defined in a flexible form. In this plan the user can configure the extension number of a local voice channel, Route a call to a remote destination and enter the Number of Digits for a specific dial prefix.
agnVoiceSwConfEntry	1.3.6.1.4.1.164.3.1.2.9.1.1		not-accessible	An entry in table.
INT agnVoiceSwConfHGConnect	1.3.6.1.4.1.164.3.1.2.9.5.1.3	INTEGER	read-write	This attribute indicates whether the hunt group should be considered in any of the mux algorithms.
INT agnVoiceSwConfHGdbIdx	1.3.6.1.4.1.164.3.1.2.9.5.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
agnVoiceSwConfHGEntry	1.3.6.1.4.1.164.3.1.2.9.5.1		not-accessible	An entry in table.
I32 agnVoiceSwConfHGExt	1.3.6.1.4.1.164.3.1.2.9.5.1.4	Integer32	read-write	This is the extension number of the hunt group. 0 is for not valid. The allowed range is 10 - 99.
STR agnVoiceSwConfHGExtString	1.3.6.1.4.1.164.3.1.2.9.5.1.5	SnmpAdminString	read-write	This is the extension string of the hunt group. This string is a combination of digits, * and #.
I32 agnVoiceSwConfHGIdx	1.3.6.1.4.1.164.3.1.2.9.5.1.2	Integer32	read-only	For Vmux-300 devices - This object represents a combination of - Hunt Group number and Extension number OR - Port number and Extension number. For other devices (e.g. MXcess, MP-2100H) - There may be up to 10 Hunt Groups per MXcess. That's the index of the hunt group relevant to this row.
INT agnVoiceSwConfHGStatus	1.3.6.1.4.1.164.3.1.2.9.5.1.7	INTEGER	read-write	This object enables the user to create/delete entries in this table. Its usage for values (1)..(6) should be identical to RowStatus SYNTAX. notApplicable(255) - should be used when the table is static (i.e. whenever create/delete entries is not allowed).
agnVoiceSwConfHGTable	1.3.6.1.4.1.164.3.1.2.9.5		not-accessible	Table of Hunt Groups.
STR agnVoiceSwConfHGUserParams	1.3.6.1.4.1.164.3.1.2.9.5.1.6	SnmpAdminString	read-write	This object indicates the User's parameters.
INT agnVoiceSwConfIdx	1.3.6.1.4.1.164.3.1.2.9.1.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
I32 agnVoiceSwConfLidt	1.3.6.1.4.1.164.3.1.2.9.1.1.6	Integer32	read-write	LIDT: Long Inter Digit Timeout used as timer between digits before routing is completed. If no digits were dialed and LIDT expired then the user will get an error tone and the call will be disconnected. 0 = notApplicable Default=15 sec.
STR agnVoiceSwConfNodeId	1.3.6.1.4.1.164.3.1.2.9.1.1.3	DisplayString	read-write	1, 2 or 3 digits, (1-9),(0-9),(0-9).
I32 agnVoiceSwConfNoOfHops	1.3.6.1.4.1.164.3.1.2.9.1.1.4	Integer32	read-write	Number of hops the frame will go through the net before deciding to discard the frame (like time-to-live in IP). 0 = notApplicable Default=20 .
INT agnVoiceSwConfRtAction	1.3.6.1.4.1.164.3.1.2.9.2.1.4	INTEGER	read-create	Action that the system should perform for the digits: agnVoiceSwConfRtDigits. The action that is allowed depends on the Dialing Plan. Here is the list of the allowed actions: For Static Dialing Plan - zone, node, in, shortDialing, hgr, del, rep For Static Dialing Plan Plus - zone, node, in, shortDialing, hgr, del, rep, numDigDP For Flexible Dialing Plan - hgr, del, rep, numDigDP, route, ext
STR agnVoiceSwConfRtData	1.3.6.1.4.1.164.3.1.2.9.2.1.5	DisplayString	read-create	This field is relevant for actions hgr(6), and rep(8), numDigDP(11) and contains the following information: For hgr - the number of the Hunt Group. For rep - the number of digits to be replaced with. For numDigDP - the number of digits collected before establishing the call. 0 indicates no defined length. In this case SIDT will be used.
INT agnVoiceSwConfRtDbId	1.3.6.1.4.1.164.3.1.2.9.2.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
STR agnVoiceSwConfRtDigits	1.3.6.1.4.1.164.3.1.2.9.2.1.3	DisplayString	read-create	Dialed digits: Series of digits 0...9, '', '#' or '%'. The '' and '#' can have many uses according to the user's decision. For example, they can be used as part of the Dialed Number, they exist on the phone number panel. '*' can also be used instead of a series of numbers. The '%' means any digits (wildcard) and is used without a series of digits. When the agnVoiceSwConfRtAction is del (7), the series of digits that are configured via this MIB object will be deleted from the prefix of the dialed number.
I32 agnVoiceSwConfRtDlci	1.3.6.1.4.1.164.3.1.2.9.2.1.8	Integer32	read-create	Routing DLCI- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). Valid values: 0=notApplicable (for non-routing case). 1, 16..991
agnVoiceSwConfRtEntry	1.3.6.1.4.1.164.3.1.2.9.2.1		not-accessible	An entry in table.
I32 agnVoiceSwConfRtIdx	1.3.6.1.4.1.164.3.1.2.9.2.1.2	Integer32	read-only	The Index of the row.
I32 agnVoiceSwConfRtMaxCalls	1.3.6.1.4.1.164.3.1.2.9.2.1.10	Integer32	read-create	Maximum no. of simultaneous voice calls that are allowed in the direction defined by the current entry. Default=0 (No Limit).
I32 agnVoiceSwConfRtPort	1.3.6.1.4.1.164.3.1.2.9.2.1.7	Integer32	read-create	Routing Port- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). 100=noConnect (for non-routing case).
I32 agnVoiceSwConfRtPriority	1.3.6.1.4.1.164.3.1.2.9.2.1.11	Integer32	read-create	This attribute indicates a unique priority of the Voice Switching Route. 1 is the lowest priority and 7 is the highest priority. 0 means N/A
ROW agnVoiceSwConfRtRowStatus	1.3.6.1.4.1.164.3.1.2.9.2.1.9	RowStatus	read-create	Status of the row for creating/deleting entries in the table. The only possible supported RowStatus vaules are active (1), notInService (2), notReady(3), createAndGo(4), createAndWait(5) and destroy(6).
INT agnVoiceSwConfRtSlot	1.3.6.1.4.1.164.3.1.2.9.2.1.6	INTEGER	read-create	Routing Slot- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13).
agnVoiceSwConfRtTable	1.3.6.1.4.1.164.3.1.2.9.2		not-accessible	Routing Table for Voice Switching.
I32 agnVoiceSwConfSidt	1.3.6.1.4.1.164.3.1.2.9.1.1.5	Integer32	read-write	SIDT: Short Inter Digit Timeout used as timer (in sec.) between digits after routing is completed. The timeout indicates end of dialing and the call can then be setup. 0 = notApplicable Default=2 sec.
agnVoiceSwConfTable	1.3.6.1.4.1.164.3.1.2.9.1		not-accessible	MXcess Configuration for Voice Switching.
STR agnVoiceSwConfZoneId	1.3.6.1.4.1.164.3.1.2.9.1.1.2	DisplayString	read-write	1 or 2 digits, (0-9)(1-9).
agnVoiceSwitching	1.3.6.1.4.1.164.3.1.2.9
agnWanGen	1.3.6.1.4.1.164.3.1.2
INT agnWebAccess	1.3.6.1.4.1.164.6.2.34.2	INTEGER	read-write	Enable/Disable accessing the device via Web. disable - no one will be allowed to access the device via Web. enable - all users are allowed Web Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSL) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSL).
agnXCmprEntry	1.3.6.1.4.1.164.3.1.2.3.7.1		not-accessible	An entry in table.
I32 agnXCmprIdx3	1.3.6.1.4.1.164.3.1.2.3.7.1.3	Integer32	read-only	3rd index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant, this attribute indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration.
I32 agnXCmprIdx4	1.3.6.1.4.1.164.3.1.2.3.7.1.4	Integer32	read-only	4th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique number of the slot position where the card is inserted. Valid values: psA(1),psB(2),clA(3),clB(4),io1(5)..io12(16); notApplicable=255.
I32 agnXCmprIdx5	1.3.6.1.4.1.164.3.1.2.3.7.1.5	Integer32	read-only	5th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt12 (12) , inPrt1 (101) .. inPrt48 (148).
I32 agnXCmprIdx6	1.3.6.1.4.1.164.3.1.2.3.7.1.6	Integer32	read-only	6th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates the Variant index. Valid values are: 0..127, 255 (= temp cnfg).Set can be performed only to the temporary configuration.
I32 agnXCmprIdx7	1.3.6.1.4.1.164.3.1.2.3.7.1.7	Integer32	read-only	7th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute is not needed. Therefore, its value will be always 255=notApplicable.
OCT agnXCmprObj	1.3.6.1.4.1.164.3.1.2.3.7.1.8	OCTET STRING	read-write	This attribute is the compressed information itself.
agnXCmprTable	1.3.6.1.4.1.164.3.1.2.3.7		not-accessible	A table.
I32 agnXCmprTypIdx	1.3.6.1.4.1.164.3.1.2.3.7.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred. One of the types is V5.1 Variant data.
I32 agnXCmprVersion	1.3.6.1.4.1.164.3.1.2.3.7.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data.
NTF alarmAIS	1.3.6.1.4.1.164.6.1.3.0.10			This trap indicates AIS.
NTF alarmFEBE	1.3.6.1.4.1.164.6.1.3.0.12			This trap indicates FEBE.
BIT alarmForwardingAction	1.3.6.1.4.1.164.6.2.50.1.11	Bits	read-create	Bit map representing the action to be performed when alarm forwarding will take place. bit 0 - No Action. '1' value - device should NOT perform any action, though other bits indicate the action to be taken. '0' value - device should perform the action/s indicated by rest of the bits. In this case, one of the other bits should be '1'. bit 1 - Interface Deactivation (of the affected Port: alarmForwardingToPort) bit 2 - OAM Signaling. Affected Port (alarmForwardingToPort) will send special OAM Signaling to the Far-End unit about the Failure. This object will be used only for devices that support Deactivation per entry OR can support more than one action.
BIT alarmForwardingCause	1.3.6.1.4.1.164.6.2.50.1.6	Bits	read-create	Bit map representing the cause upon which alarm forwarding will take place. bit 0 - LOSS (LINE DOWN) bit 1 - AIS bit 2 - RDI bit 3 - PROTOCOL DOWN.
U32 alarmForwardingDelay	1.3.6.1.4.1.164.6.2.50.1.9	Unsigned32	read-create	This parameter determines the period of time (in seconds) the alarm of the alarmForwardingFailPort should exist before starting alarm forwarding.
INT alarmForwardingDirection	1.3.6.1.4.1.164.6.2.50.1.10	INTEGER	read-create	This parameter determines the Direction of the Alarm Forwarding. unidirectional - alarmForwardingFailPort affects the alarmForwardingToPort. bidirectional - alarmForwardingFailPort affects the alarmForwardingToPort AND vice-versa. For such cases, this value will be selected, instead of entering an additional unidirectional entry in the table, where the indexes are swapped.
alarmForwardingEntry	1.3.6.1.4.1.164.6.2.50.1		not-accessible	Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.
I32 alarmForwardingFailPort	1.3.6.1.4.1.164.6.2.50.1.1	Integer32	not-accessible	An Index of the port on which a fail occurs.
I32 alarmForwardingGroupConditions	1.3.6.1.4.1.164.6.2.50.1.5	Integer32	read-create	This parameter is applicable when there is a group of interfaces in which a fault may occur, and one interface to which alarm is propagated (forwarded). 0 = All - Forwarding will take place only when all interfaces of the same group are faulty. 1 = Single - Forwarding will take place when at least one (single) interface of the same group (any of them) is faulty. n - forwarding will take place only when n (n < all) interfaces of the same group fail.
INT alarmForwardingRecoveryCommand	1.3.6.1.4.1.164.6.2.50.1.8	INTEGER	read-create	This parameter is a command. It is applicable when alarmForwardingRecoveryMode = manual. on - Will stop alarm forwarding. After setting to 'On', the agent will set this parameter back to 'Off'.
INT alarmForwardingRecoveryMode	1.3.6.1.4.1.164.6.2.50.1.7	INTEGER	read-create	This parameter determines the Recovery Mode. manual - The user should stop the alarm forwarding by using the alarmForwardingRecoveryCommand. automatic - Alarm forwarding will be automatically stopped upon alarmForwardingFailPort recovery.
I32 alarmForwardingRecoveryTime	1.3.6.1.4.1.164.6.2.50.1.4	Integer32	read-create	This parameter defines the maximum time (sec) the affected port will hold the down state.
ROW alarmForwardingRowStatus	1.3.6.1.4.1.164.6.2.50.1.3	RowStatus	read-create	Creation/ Deletion of rows in the table.
alarmForwardingTable	1.3.6.1.4.1.164.6.2.50		not-accessible	The Alarm Forwarding Mechanism will be operated for this table entries.
I32 alarmForwardingToPort	1.3.6.1.4.1.164.6.2.50.1.2	Integer32	not-accessible	An Index of the port that will be affected upon the failure of the alarmForwardingFailPort.
NTF alarmLOF	1.3.6.1.4.1.164.6.1.3.0.8			This trap indicates Loss Of Frame.
NTF alarmLOS	1.3.6.1.4.1.164.6.1.3.0.7			This trap indicates Loss Of Signal.
NTF alarmRDI	1.3.6.1.4.1.164.6.1.3.0.11			This trap indicates RDI.
INT alarmSeverity	1.3.6.1.4.1.164.6.2.20	INTEGER	read-only	This object specifies the severity of the alarms.
INT alarmState	1.3.6.1.4.1.164.6.2.21	INTEGER	read-only	.
NTF alarmStatusTrap	1.3.6.1.4.1.164.6.1.3.0.5			The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm.
NTF alarmsTrap	1.3.6.1.4.1.164.3.2.0.1			This trap is sent whenever alarm occurs in the agent.
U32 alrBufCode	1.3.6.1.4.1.164.3.1.2.4.1.1.3	Unsigned32	read-only	A code identifying the alarm of an entry in the alarm buffer table.
STR alrBufDescription	1.3.6.1.4.1.164.3.1.2.4.1.1.2	DisplayString	read-only	This entry is a unique text description of the alarm in the buffer. The alarm description includes the following information: alarm code, slot id, card type, channel id , alarm text, alarm status, masked flag and event counter
alrBufEntry	1.3.6.1.4.1.164.3.1.2.4.1.1		not-accessible	An entry in table.
INT alrBufferClearCmd	1.3.6.1.4.1.164.3.1.2.4.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2). For MP-2100/2200, this command will not really erase the Alarm Buffer, but is only an ACK of seeing the Buffer. It marks a pointer of the last entry's alrBufIdx, in order to allow view of new alarms entered after this pointer (alrBufIdxUponLastAck).
alrBuffGen	1.3.6.1.4.1.164.3.1.2.4
I32 alrBufIdx	1.3.6.1.4.1.164.3.1.2.4.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify this entry
U32 alrBufIdxUponLastAck	1.3.6.1.4.1.164.3.1.2.4.3	Unsigned32	read-only	This attribute indicates the value of alrBufIdx for the last existing entry of alrBufTable, when alrBufferClearCmd was last Set to on(3). That will enable a user to see only Alarms that entered the alrBufTable after last Set of alrBufferClearCmd, by GetNext of alrBufDescription with this index.
U32 alrBufPort	1.3.6.1.4.1.164.3.1.2.4.1.1.5	Unsigned32	read-only	The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999.
INT alrBufSeverity	1.3.6.1.4.1.164.3.1.2.4.1.1.6	INTEGER	read-only	The severity of the alarm.
INT alrBufSlot	1.3.6.1.4.1.164.3.1.2.4.1.1.4	INTEGER	read-only	The slot number this alarm refers to. When the alarm refers to a system alarm, the value will be 'notApplicable(255)'.
INT alrBufState	1.3.6.1.4.1.164.3.1.2.4.1.1.7	INTEGER	read-only	State of the alarm (On/Off).
alrBufTable	1.3.6.1.4.1.164.3.1.2.4.1		not-accessible	A table.
I32 alrGenCode	1.3.6.1.4.1.164.3.3.4.3.1.1	Integer32	read-only	This object is a unique code number, identifying a certain alarm.
I32 alrGenDebounce	1.3.6.1.4.1.164.3.3.4.3.1.6	Integer32	read-write	Debounce time for each alarm code, in seconds. The meaning is, that an alarm will be 'declared' as ON (or OFF), only after it was actually ON/OFF the Debouncing time selected by user. 0 = default debounce selection (each alarm has a default value). 250 = maximum value of seconds for debounce. 253 = mask = the alarm will Never be reported. 254 = default debounce selection (each alarm has a default value). 255 = not applicable
INT alrGenDefSeverity	1.3.6.1.4.1.164.3.3.4.3.1.7	INTEGER	read-only	This object reports the default severity of each alarm. User can change the severity of the alarms defined by this default via the alrGenSeverity object.
STR alrGenDescription	1.3.6.1.4.1.164.3.3.4.3.1.2	DisplayString	read-only	This entry is a unique text description, of the alarm corresponding to the specified code.
alrGenEntry	1.3.6.1.4.1.164.3.3.4.3.1		not-accessible	An entry in table.
INT alrGenLevel	1.3.6.1.4.1.164.3.3.4.3.1.3	INTEGER	read-only	Alarm level.
INT alrGenSeverity	1.3.6.1.4.1.164.3.3.4.3.1.5	INTEGER	read-write	This object enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code).
INT alrGenSlotType	1.3.6.1.4.1.164.3.3.4.3.1.4	INTEGER	read-only	Slot type that the alarm is relevant to. clAndIo - an alarm that is relevant for both CL and IO slots.
alrGenTable	1.3.6.1.4.1.164.3.3.4.3		not-accessible	A table.
NTF atmAceAlarmCluster	1.3.6.1.4.1.164.6.1.12.0.36			This trap is sent upon atmNteAlarmType start or end, for a cluster of VPs/VCs (according to atmNteLevel) with the same alarm on the same physical port. This trap replaces sending the same alarm for a big quantity (the quantity described in the product specification document) of VPs/VCs in order to prevent flooding the NMS and the network with traps.
NTF atmAceAlarmForwardingTrap	1.3.6.1.4.1.164.6.1.12.0.7			This trap is sent upon starting or stopping Alarm Forwarding Mechanism.
NTF atmAceAlarmLCD	1.3.6.1.4.1.164.6.1.12.0.18			This trap indicates Loss of Cell Delineation.
NTF atmAceAlarmLineAIS	1.3.6.1.4.1.164.6.1.12.0.21			This trap indicates Line AIS.
NTF atmAceAlarmLineBIP	1.3.6.1.4.1.164.6.1.12.0.26			This trap indicates Line Bit Interleave Parity.
NTF atmAceAlarmLineFEBE	1.3.6.1.4.1.164.6.1.12.0.28			This trap indicates Line Far End Block Error.
NTF atmAceAlarmLineRDI	1.3.6.1.4.1.164.6.1.12.0.23			This trap indicates Line RDI.
NTF atmAceAlarmLOF	1.3.6.1.4.1.164.6.1.12.0.17			This trap indicates Loss Of Frame.
NTF atmAceAlarmLOP	1.3.6.1.4.1.164.6.1.12.0.20			This trap indicates Loss of Pointer.
NTF atmAceAlarmLOS	1.3.6.1.4.1.164.6.1.12.0.16			This trap indicates Loss Of Signal.
NTF atmAceAlarmPathAIS	1.3.6.1.4.1.164.6.1.12.0.22			This trap indicates Path AIS.
NTF atmAceAlarmPathBIP	1.3.6.1.4.1.164.6.1.12.0.27			This trap indicates Path Bit Interleave Parity.
NTF atmAceAlarmPathFEBE	1.3.6.1.4.1.164.6.1.12.0.29			This trap indicates Path Far End Block Error.
NTF atmAceAlarmPathRDI	1.3.6.1.4.1.164.6.1.12.0.24			This trap indicates Path RDIand Path RAI(Yellow) for DS1 interfaces.
NTF atmAceAlarmPlcpBIP	1.3.6.1.4.1.164.6.1.12.0.32			This trap indicates T3 Plcp Bit Interleave Parity.
NTF atmAceAlarmPlcpFEBE	1.3.6.1.4.1.164.6.1.12.0.33			This trap indicates T3 Plcp Far End Block Error.
NTF atmAceAlarmPlcpLOF	1.3.6.1.4.1.164.6.1.12.0.30			This trap indicates T3 PLCP Loss Of Frame.
NTF atmAceAlarmPlcpP1P2	1.3.6.1.4.1.164.6.1.12.0.34			This trap indicates T3 Plcp Parity errors in P1/P2 bytes.
NTF atmAceAlarmPlcpYELLOW	1.3.6.1.4.1.164.6.1.12.0.31			This trap indicates T3 Plcp Yellow.
NTF atmAceAlarmSectionBIP	1.3.6.1.4.1.164.6.1.12.0.25			This trap indicates Section Bit Interleave Parity.
NTF atmAceAlarmSLM	1.3.6.1.4.1.164.6.1.12.0.19			This trap indicates Signal Line Mismatch.
NTF atmAceAlarmTrap	1.3.6.1.4.1.164.12.3.0.2			The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm. An active alarm state exists if: 1) The atmInterfaceActiveAlarms vector is different than 0. 2) The atmNteAlarmVpTable contains entries. 3) The atmNteAlarmVcTable contains entries. The trap is also sent when a transition into the no alarm state occurs. The second variable will be atmInterfaceActiveAlarms to indicate the kind of the alarm. The trap is not sent more than once in a 10 second interval.
NTF atmAceAlarmUAS	1.3.6.1.4.1.164.6.1.12.0.35			This trap is sent upon UAS start or end per port.
NTF atmAceAlarmVcAISReception	1.3.6.1.4.1.164.6.1.12.0.57			This trap indicates AIS Reception on a VC.
NTF atmAceAlarmVcContinuityLoss	1.3.6.1.4.1.164.6.1.12.0.56			This trap indicates Loss of Continuity Check on a VC Connection.
NTF atmAceAlarmVcErroredCells	1.3.6.1.4.1.164.6.1.12.0.59			This trap indicates Errored Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcGCRAViolation	1.3.6.1.4.1.164.6.1.12.0.65			This trap indicates GCRA violation on a VC Connection reported by UPC device.
NTF atmAceAlarmVcLoopback	1.3.6.1.4.1.164.6.1.12.0.64			This trap is sent upon OAM LoopBack fail status per VC.
NTF atmAceAlarmVcLostCells	1.3.6.1.4.1.164.6.1.12.0.60			This trap indicates Lost Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcMisinsertedCells	1.3.6.1.4.1.164.6.1.12.0.61			This trap indicates Misinserted Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcRDIReception	1.3.6.1.4.1.164.6.1.12.0.58			This trap indicates RDI Reception on a VC Connection.
NTF atmAceAlarmVcUAS	1.3.6.1.4.1.164.6.1.12.0.63			This trap is sent upon UAS start or end per VC.
NTF atmAceAlarmVcUnexpectedCell	1.3.6.1.4.1.164.6.1.12.0.62			This trap indicates an unexpected cell from user or network port.
NTF atmAceAlarmVpAISReception	1.3.6.1.4.1.164.6.1.12.0.41			This trap indicates AIS Reception on a VP Connection.
NTF atmAceAlarmVpContinuityLoss	1.3.6.1.4.1.164.6.1.12.0.40			This trap indicates Loss of Continuity Check on a VP Connection.
NTF atmAceAlarmVpErroredCells	1.3.6.1.4.1.164.6.1.12.0.43			This trap indicates Errored Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpGCRAViolation	1.3.6.1.4.1.164.6.1.12.0.48			This trap indicates GCRA violation on a VP Connection reported by UPC device.
NTF atmAceAlarmVpLoopback	1.3.6.1.4.1.164.6.1.12.0.47			This trap is sent upon OAM LoopBack fail status per VP.
NTF atmAceAlarmVpLostCells	1.3.6.1.4.1.164.6.1.12.0.44			This trap indicates Lost Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpMisinsertedCells	1.3.6.1.4.1.164.6.1.12.0.45			This trap indicates Misinserted Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpRDIReception	1.3.6.1.4.1.164.6.1.12.0.42			This trap indicates RDI Reception on a VP Connection.
NTF atmAceAlarmVpUAS	1.3.6.1.4.1.164.6.1.12.0.46			This trap is sent upon UAS start or end per VP.
NTF atmAceDateAndTimeRequest	1.3.6.1.4.1.164.6.1.12.0.8			This trap is sent upon restart. Upon recieving this trap the NMS will set the device's date and time. This trap's purpose is to fix a problem in ACE2002, ACE-2002E, ACE-202. The problem is that the Date and Time is stored in the NVRAM, and when the NVRAM's battery is empty, the device loses this information.
NTF atmAceHwFailure	1.3.6.1.4.1.164.6.1.12.0.37			This trap is sent upon HW failure per port.
NTF atmAceModuleChangeTrap	1.3.6.1.4.1.164.12.3.0.3			The trap is sent every time a module is changed (Hot swapping). The second variable will be atmNteCardType to indicate the type of card that was inserted. The value empty(255) indicates that a card was taken out.
NTF atmAceModuleMismatchTrap	1.3.6.1.4.1.164.12.3.0.5			The trap is sent upon starting or stopping of a module mismatch state. A possible mismatch is when the inserted module is other than the programmed one.
NTF atmAceRedundancyTrap	1.3.6.1.4.1.164.12.3.0.4			The trap is sent upon change in link as a result of redundancy. The ifIndex parameter indicates the current active link.
NTF atmAceStatusChange	1.3.6.1.4.1.164.12.3.0.1			The trap is sent every time there is a change in the state of one of the LEDs.
NTF atmAceSystemTrap	1.3.6.1.4.1.164.6.1.12.0.6			This trap alerts of major problems in the device.
NTF atmAceUnavailableBwTrap	1.3.6.1.4.1.164.6.1.12.0.38			This trap is sent when Bandwidth allocation is > max possible value for the installed card. For ACE2002 this trap will be sent for the following cases: Card insertion - if the total Input and/or Output Bandwidth is over allocated, then the specific card rate will be set to 0 and this trap will be sent with the Input/Output rates values. Upgrade from former version - when an over allocated Bandwidth is detected, this trap will be sent with atmConfIfInputRate=atmConfIfOutputRate=0xFFFFFFFF.
atmAlarmForwardingEntry	1.3.6.1.4.1.164.12.3.1.1.32.1		not-accessible	Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.
I32 atmAlarmForwardingFailPort	1.3.6.1.4.1.164.12.3.1.1.32.1.1	Integer32	not-accessible	An Index of the port on which a fail occurs.
BIT atmAlarmForwardingFailureLevel	1.3.6.1.4.1.164.12.3.1.1.32.1.4	Bits	read-create	This parameter determines the level of failure that will operate the Alarm Forwarding Mechanism.
INT atmAlarmForwardingRecoveryCommand	1.3.6.1.4.1.164.12.3.1.1.32.1.6	INTEGER	read-create	This parameter is a command. It is applicable when atmAlarmForwardingRecoveryMode = manual. on - Will stop the RDI transmission. After setting to 'On' the agent will set this parameter back to 'Off'.
INT atmAlarmForwardingRecoveryMode	1.3.6.1.4.1.164.12.3.1.1.32.1.5	INTEGER	read-create	This parameter determines the Recovery Mode. manual - The user should stop the RDI transmission by using the atmAlarmForwardingRecoveryCommand. automatic - The RDI transmission will be automatically stopped upon atmAlarmForwardingFailPort recovery.
ROW atmAlarmForwardingRowStatus	1.3.6.1.4.1.164.12.3.1.1.32.1.3	RowStatus	read-create	Creation/Deletion of rows in the table.
atmAlarmForwardingTable	1.3.6.1.4.1.164.12.3.1.1.32		not-accessible	The Alarm Forwarding Mechanism will be operated for this table entries.
U32 atmAlarmForwardingTimeFilterWindow	1.3.6.1.4.1.164.12.3.1.1.32.1.7	Unsigned32	read-create	This parameter determines the Time Filter Window, meaning: how much time (in seconds) should the alarm exist in order to start the Alarm Forwarding operation.
I32 atmAlarmForwardingToPort	1.3.6.1.4.1.164.12.3.1.1.32.1.2	Integer32	not-accessible	An Index of the port that will be affected upon the failure of the atmAlarmForwardingFailPort.
INT atmConfAlarmForwarding	1.3.6.1.4.1.164.12.3.2.1.1.1.9	INTEGER	read-write	Enables Path AIS Alarm forwarding upon a failure detection. The following might be considered as a failure: LOS, LOF, LOC, SLM, LOP, Path AIS and Line AIS. disable(2) - will not forward an alarm upon a failure on this port. enable(3) - will forward an alarm upon a failure on this port.
INT atmConfAtmIfVpiVciLimit	1.3.6.1.4.1.164.12.3.2.1.1.1.5	INTEGER	read-only	The limit on the sum of the VPI+VCI bits for this interface.
I32 atmConfIfAllocatedBw	1.3.6.1.4.1.164.12.3.2.1.1.1.10	Integer32	read-only	Total VC Bandwidth Allocation.
INT atmConfIfCardType	1.3.6.1.4.1.164.12.3.2.1.1.1.4	INTEGER	read-only	The card type.
INT atmConfIfFrameType	1.3.6.1.4.1.164.12.3.2.1.1.1.3	INTEGER	read-write	The frame type. Valid values for a 155M interface: sonet(2), sdh(3). Valid values for a T3 interface: direct(4), plcpInternal(5), plcpExternal(6), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbling(12). Valid values for Ethernet interface: ethCrcTrans (8), ethCrcNotTrans(9). (DS1 interfaces frame type is specified in the DSX1 mib).
INT atmConfIfHwFeatures	1.3.6.1.4.1.164.12.3.2.1.1.1.6	INTEGER	read-write	HW features command.
I32 atmConfIfInputRate	1.3.6.1.4.1.164.12.3.2.1.1.1.8	Integer32	read-write	This parameter indicates the input rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.
INT atmConfIfLoopback	1.3.6.1.4.1.164.12.3.2.1.1.1.2	INTEGER	read-write	Interface Loopback.
I32 atmConfIfLowerVpi	1.3.6.1.4.1.164.12.3.2.1.1.1.11	Integer32	read-write	The Lower possible VPI.
INT atmConfIfOamFailureInd	1.3.6.1.4.1.164.12.3.2.1.1.1.13	INTEGER	read-write	This object allows user to define the type of indication (if any) that will be created upon a LB cell failure, for all VCs on which OAM loopback traffic is activated. disabled(2) - no indication will be created. ais(3) - will cause Tx of AIS. rdi(4) - will cause Tx of RDI. aisAndRdi(5) - will cause Tx of AIS & RDI. For LA-110, indication will be sent only for VCs with atmConfVcLoopbackFailureInd <> disabled
INT atmConfIfOamMode	1.3.6.1.4.1.164.12.3.2.1.1.1.12	INTEGER	read-write	OAM support Mode, which determines the interface's location in a segment wise.
I32 atmConfIfOutputRate	1.3.6.1.4.1.164.12.3.2.1.1.1.7	Integer32	read-write	This parameter indicates the output rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.
INT atmConfIfTransmitClk	1.3.6.1.4.1.164.12.3.2.1.1.1.1	INTEGER	read-write	The transmit clock of the port.
INT atmConfVpCCAdminStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.2	INTEGER	read-write	up(2) - Activate Continuity Check (CC). down(3) - Deactivate CC. source(4) - Activate OAM CC(Continuity Check) of local agent ( start sending Oam cells to the remote side ). sink(5) - Activate CC of remote agent ( start receiving Oam cells from remote side ). listenToActivationCells (6) - Passive listener till gets an activation request originateActivationCells(7) - Sands Activation cell according to atmConfVcCCDirection.
INT atmConfVpCCDirection	1.3.6.1.4.1.164.12.3.2.1.3.1.6	INTEGER	read-write	both(2) - Agent send OAM CC cells and check received OAM CC cells source(4)- Agent send OAM CC cells. sink(5) - Agent checks received OAM CC cells.
INT atmConfVpCCOperStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.9	INTEGER	read-only	initial(1) - The CC activation process is not started. source(4) - Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells. both (8) - OAM CC of local and remote agents activation. timeout (9) - Timeout occured on receiving answer from the remote agent. denied (10) - CC activation process rejected by remote agent. conflict (11) - local and remote sides requested activation simultaneously. manual (12) - OAM CC of local agent activated manually.
OCT atmConfVpCongestionControl	1.3.6.1.4.1.164.12.3.2.1.3.1.5	OCTET STRING	read-write	Each bit indicates a selection of one option as the following description. All combinations are possible and legal. The codes are: 1 - EPD 2 - CLP 4 - EFCI
INT atmConfVpConnected	1.3.6.1.4.1.164.12.3.2.1.3.1.15	INTEGER	read-write	This object indicates whether this VP is connected and if connected, what is it connected to.
DAT atmConfVpCreationTime	1.3.6.1.4.1.164.12.3.2.1.3.1.7	DateAndTime	read-only	A date-time in which the VP was created.
INT atmConfVpLoopbackAdminStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.3	INTEGER	read-write	up(2) - Start loopback OAM cells. down(3) - Stop sending loopback OAM cells. For ace2002: up(2) - Transmitting LB cells with llid all ones (i.e. FFFF..FF) down(3) - Not transmitting LB cells. llid(4) - Transmitting LB cells with llid indicated in the address field. segment(5) - Transmitting Segment LB cells with llid all ones. endToEnd(6) - Transmitting End to End LB cells with llid all ones. segmentLlid(7) - Transmitting Segment LB cells with llid indicated in the address field. endToEndLlid(8) - Transmitting LB cells with llid indicated in the address field. This parameter value might be in conflict with atmConfVpOamSupport value, since this parameter is for LB, while atmConfVpOamSupport is for any other OAM cells.
INT atmConfVpLoopbackFailureInd	1.3.6.1.4.1.164.12.3.2.1.3.1.11	INTEGER	read-write	This object allows user to define the Indication that will be created upon a LB cell failure. disabled(2) - no indication will be created. segmentAis(3) - will cause Tx of a segment AIS. segmentRdi(4) - will cause Tx of a segment RDI. segmentAisAndRdi(5) - will cause Tx of a segment AIS & RDI. endToEndAis(6) - will cause Tx of an End to End AIS. endToEndRdi(7) - will cause Tx of an End to End RDI. endToEndAisAndRdi(8) - will cause Tx of an End to End AIS & RDI. Default: disabled(2).
I32 atmConfVpLoopbackFailureThreshold	1.3.6.1.4.1.164.12.3.2.1.3.1.12	Integer32	read-write	The number of the LB failures before starting transmission of the Indication defined by atmConfVcLoopbackFailureInd. Range: 1..16. Default: 1.
OCT atmConfVpLoopbackSinkAddress	1.3.6.1.4.1.164.12.3.2.1.3.1.4	OCTET STRING	read-write	Destination address. For ace101: 2 bytes are used. For ace2002: 16 bytes are used.
INT atmConfVpLoopbackTraffic	1.3.6.1.4.1.164.12.3.2.1.3.1.10	INTEGER	read-write	This parameter has both command and status meanings: off(2) - Set to 'Off' will Stop traffic loop. Getting this value means that the loop is not running. on (3) - Set to 'On' will start traffic loop. Getting this value means that the loop is currently running.
I32 atmConfVpOamDescrIndex	1.3.6.1.4.1.164.12.3.2.1.3.1.14	Integer32	read-write	This parameter indicates the VPL's OAM Descriptor index, according to the OAM Descriptor Configuration Table.
INT atmConfVpOamDirection	1.3.6.1.4.1.164.12.3.2.1.3.1.13	INTEGER	read-write	The direction of OAM cell insertion. downStream(2) - The OAM cell will be inserted in downStream. upStream(3) - The OAM cell will be inserted in upStream.
INT atmConfVpOamSupport	1.3.6.1.4.1.164.12.3.2.1.3.1.8	INTEGER	read-write	OAM support mode, which determines the device location in a segment wise.
INT atmConfVpPolicing	1.3.6.1.4.1.164.12.3.2.1.3.1.1	INTEGER	read-write	Policing method desired for this VPL.
atmGen	1.3.6.1.4.1.164.12.2
G32 atmGenSysCxRefCounter	1.3.6.1.4.1.164.12.2.2.1.5.1.2	Gauge32	read-only	The counter counts the number of references that have been made to the object .
atmGenSysCxRefEntry	1.3.6.1.4.1.164.12.2.2.1.5.1		not-accessible	The entries will be added by the agent upon an entry addition in the referenced tables (TD table, FR Descriptor etc.)
I32 atmGenSysCxRefIndex	1.3.6.1.4.1.164.12.2.2.1.5.1.1	Integer32	read-only	The index specifies an entry in the table of the object.
atmGenSysCxRefTable	1.3.6.1.4.1.164.12.2.2.1.5		not-accessible	A Cross Reference table. The table maintains an index of an object which is also the table index, and a counter that indicates how many times this object was referenced. When using this table for more than one referenced table, which uses the same range of indexes, then the index should be shifted by a unique offset per table. In ACE2002 this table is used for TD and for FR Desc. Thus, the index for FR Descriptor is: FR Descriptor index + offset. The offset is described in the ACE2002 NMS SRS.
atmGenSysGen	1.3.6.1.4.1.164.12.2.2.1
INT atmGenSysLogClearAll	1.3.6.1.4.1.164.12.2.2.1.2	INTEGER	read-write	Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).
atmGenSysLogEntry	1.3.6.1.4.1.164.12.2.2.1.3.1		not-accessible	An entry in table.
I32 atmGenSysLogIndex	1.3.6.1.4.1.164.12.2.2.1.3.1.1	Integer32	read-only	The index of the log buffer.
STR atmGenSysLogMessage	1.3.6.1.4.1.164.12.2.2.1.3.1.2	DisplayString	read-only	The log buffer entry message text.
atmGenSysLogTable	1.3.6.1.4.1.164.12.2.2.1.3		not-accessible	A copy of the log buffer.
atmGenSysSelfTestEntry	1.3.6.1.4.1.164.12.2.2.1.1.1		not-accessible	An entry in table.
I32 atmGenSysSelfTestIndex	1.3.6.1.4.1.164.12.2.2.1.1.1.1	Integer32	read-only	A running index for the table.
STR atmGenSysSelfTestModule	1.3.6.1.4.1.164.12.2.2.1.1.1.3	DisplayString	read-only	The name of module on which the test was performed.
STR atmGenSysSelfTestResult	1.3.6.1.4.1.164.12.2.2.1.1.1.2	DisplayString	read-only	The results of the initial testing of the device.
atmGenSysSelfTestTable	1.3.6.1.4.1.164.12.2.2.1.1		not-accessible	A table containing the results of the initial testing of the device.
INT atmGenSysSetDefaultConfg	1.3.6.1.4.1.164.12.2.2.1.4	INTEGER	read-write	When set to on(3), the agent will set all the configuration parameters to their default values. The variable is then reset to off(2) by the agent. The agent must be reset for the default configuration to apply.
atmGenSystem	1.3.6.1.4.1.164.12.2.2
G32 atmIfCurrentCorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.2.1.3	Gauge32	read-only	The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in the current 15 minute interval.
atmIfCurrentEntry	1.3.6.1.4.1.164.12.2.1.1.2.1		not-accessible	An entry in the ATM interface Current table.
G32 atmIfCurrentHecErrorSeconds	1.3.6.1.4.1.164.12.2.1.1.2.1.5	Gauge32	read-only	The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentRxCells	1.3.6.1.4.1.164.12.2.1.1.2.1.2	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface in the current 15 minute interval.
atmIfCurrentTable	1.3.6.1.4.1.164.12.2.1.1.2		not-accessible	The ATM interface Current table.
G32 atmIfCurrentTxCells	1.3.6.1.4.1.164.12.2.1.1.2.1.1	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.2.1.4	Gauge32	read-only	The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in the current 15 minute interval.
atmIfDataEntry	1.3.6.1.4.1.164.12.2.1.1.1.1		not-accessible	An entry in the ATM interface Data table.
atmIfDataTable	1.3.6.1.4.1.164.12.2.1.1.1		not-accessible	The ATM interface Data table.
G32 atmIfIntervalCorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.3.1.4	Gauge32	read-only	The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
atmIfIntervalEntry	1.3.6.1.4.1.164.12.2.1.1.3.1		not-accessible	An entry in the ATM interface Interval table.
G32 atmIfIntervalHecErrorSeconds	1.3.6.1.4.1.164.12.2.1.1.3.1.6	Gauge32	read-only	The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
I32 atmIfIntervalNumber	1.3.6.1.4.1.164.12.2.1.1.3.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmIfIntervalRxCells	1.3.6.1.4.1.164.12.2.1.1.3.1.3	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
atmIfIntervalTable	1.3.6.1.4.1.164.12.2.1.1.3		not-accessible	The ATM interface Interval table.
G32 atmIfIntervalTxCells	1.3.6.1.4.1.164.12.2.1.1.3.1.2	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.3.1.5	Gauge32	read-only	The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
atmIfPerformance	1.3.6.1.4.1.164.12.2.1.1
C32 atmIfRxCells	1.3.6.1.4.1.164.12.2.1.1.1.1.4	Counter32	read-only	The counter associated with the total number of received cells, encountered by an ATM interface.
I32 atmIfTimeElapsed	1.3.6.1.4.1.164.12.2.1.1.1.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
C32 atmIfTxCells	1.3.6.1.4.1.164.12.2.1.1.1.1.3	Counter32	read-only	The counter associated with the total number of transmitted cells, encountered by an ATM interface.
C32 atmIfUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.1.1.5	Counter32	read-only	The counter associated with the total number of cells with uncorrected HEC errors, encountered by an ATM interface.
I32 atmIfValidIntervals	1.3.6.1.4.1.164.12.2.1.1.1.1.2	Integer32	read-only	The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
I32 atmInterfaceActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.2.1.1	Integer32	read-only	A Bit String of the active alarms on this interface. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - LOS 2 - LOF 3 - Line AIS (SONET)/ PLCP LOF (DS3) 4 - LOP 5 - Path AIS 6 - SLM 7 - LCD 8 - Line RDI (SONET)/ PLCP Yellow (DS3) 9 - Path RDI (SONET)/ RDI (DS3) 10 - Section BIP (SONET)/ P1/P2 (DS3) > Threshold 11 - Line BIP (SONET)/ PLCP BIP (DS3) > Threshold 12 - Line FEBE (SONET)/ PLCP FEBE (DS3) > Threshold 13 - Path BIP > Threshold 14 - Path FEBE > Threshold 15 - HW Failure
INT atmInterfaceAlarmStatus	1.3.6.1.4.1.164.12.3.2.1.2.1.10	INTEGER	read-only	The variable is on(3) when there is any active alarm on this interface.
I32 atmInterfaceMaskAlarms	1.3.6.1.4.1.164.12.3.2.1.2.1.11	Integer32	read-write	A Bit String of alarms mask on this interface. An up bit (1) means that the respective alarm is masked. A down bit (0) means no mask. The mask is supported for the following alarms: 1 - LOS
STR atmIntervalDateDate	1.3.6.1.4.1.164.12.2.1.3.1.2	DisplayString	read-only	The date corresponding to this interval.
atmIntervalDateEntry	1.3.6.1.4.1.164.12.2.1.3.1		not-accessible	The date & time for the given interval.
I32 atmIntervalDateInterval	1.3.6.1.4.1.164.12.2.1.3.1.1	Integer32	read-only	The interval number defining this entry.
atmIntervalDateTable	1.3.6.1.4.1.164.12.2.1.3		not-accessible	The agent will keep in this group the date & time corresponding to each interval.
STR atmIntervalDateTime	1.3.6.1.4.1.164.12.2.1.3.1.3	DisplayString	read-only	The time corresponding to this interval.
I32 atmLoopbackVcAverageDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.6	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVcCDV	1.3.6.1.4.1.164.12.3.2.2.2.1.5	Integer32	read-only	Cell Delay Variation for this sampling.
atmLoopbackVcEntry	1.3.6.1.4.1.164.12.3.2.2.2.1		not-accessible	An entry in table.
I32 atmLoopbackVcErrSessions	1.3.6.1.4.1.164.12.3.2.2.2.1.9	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
I32 atmLoopbackVcIfIndex	1.3.6.1.4.1.164.12.3.2.2.2.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVcIvlAverageDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.7	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVcIvlCDV	1.3.6.1.4.1.164.12.3.2.2.4.1.6	Integer32	read-only	Cell Delay Variation for this interval.
atmLoopbackVcIvlEntry	1.3.6.1.4.1.164.12.3.2.2.4.1		not-accessible	An entry in table.
I32 atmLoopbackVcIvlErrSessions	1.3.6.1.4.1.164.12.3.2.2.4.1.10	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
I32 atmLoopbackVcIvlIfIndex	1.3.6.1.4.1.164.12.3.2.2.4.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVcIvlIvl	1.3.6.1.4.1.164.12.3.2.2.4.1.4	Integer32	read-only	The relevant interval number.
I32 atmLoopbackVcIvlMaxDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.8	Integer32	read-only	The maximum delay without including lost cells.
I32 atmLoopbackVcIvlMinDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.9	Integer32	read-only	The minimum delay.
INT atmLoopbackVcIvlOperStatus	1.3.6.1.4.1.164.12.3.2.2.4.1.5	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VC during this interval. -inProgress(2) has no meaning per interval. -failed(3) means there was problem for this test during this interval. -endSuccessfully(4) means that the test was OK.
atmLoopbackVcIvlTable	1.3.6.1.4.1.164.12.3.2.2.4		not-accessible	This table contains parameters for an OAM VC loopback test.
I32 atmLoopbackVcIvlVci	1.3.6.1.4.1.164.12.3.2.2.4.1.3	Integer32	read-only	The VCI of the OAM VCL.
I32 atmLoopbackVcIvlVpi	1.3.6.1.4.1.164.12.3.2.2.4.1.2	Integer32	read-only	The VPI of the OAM VCL.
I32 atmLoopbackVcMaxDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.7	Integer32	read-only	The maximum delay without including lost cells.
I32 atmLoopbackVcMinDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.8	Integer32	read-only	The minimum delay.
INT atmLoopbackVcOperStatus	1.3.6.1.4.1.164.12.3.2.2.2.1.4	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.
atmLoopbackVcTable	1.3.6.1.4.1.164.12.3.2.2.2		not-accessible	This table contains parameters for an OAM VC loopback test.
I32 atmLoopbackVcVci	1.3.6.1.4.1.164.12.3.2.2.2.1.3	Integer32	read-only	The VCI of the OAM VCL.
I32 atmLoopbackVcVpi	1.3.6.1.4.1.164.12.3.2.2.2.1.2	Integer32	read-only	The VPI of the OAM VCL.
I32 atmLoopbackVpAverageDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.5	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVpCDV	1.3.6.1.4.1.164.12.3.2.2.1.1.4	Integer32	read-only	Cell Delay Variation for this sampling.
atmLoopbackVpEntry	1.3.6.1.4.1.164.12.3.2.2.1.1		not-accessible	An entry in table atmLoopbackVpTable.
I32 atmLoopbackVpErrSessions	1.3.6.1.4.1.164.12.3.2.2.1.1.8	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
I32 atmLoopbackVpIfIndex	1.3.6.1.4.1.164.12.3.2.2.1.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVpIvlAverageDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.6	Integer32	read-only	Average delay without including lost cells for this interval.
I32 atmLoopbackVpIvlCDV	1.3.6.1.4.1.164.12.3.2.2.3.1.5	Integer32	read-only	Cell Delay Variation for this interval.
atmLoopbackVpIvlEntry	1.3.6.1.4.1.164.12.3.2.2.3.1		not-accessible	An entry in table.
I32 atmLoopbackVpIvlErrSessions	1.3.6.1.4.1.164.12.3.2.2.3.1.9	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
I32 atmLoopbackVpIvlIfIndex	1.3.6.1.4.1.164.12.3.2.2.3.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVpIvlIvl	1.3.6.1.4.1.164.12.3.2.2.3.1.3	Integer32	read-only	The relevant interval number.
I32 atmLoopbackVpIvlMaxDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.7	Integer32	read-only	The maximum delay without including lost cells for this interval.
I32 atmLoopbackVpIvlMinDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.8	Integer32	read-only	The minimum delay for this interval.
INT atmLoopbackVpIvlOperStatus	1.3.6.1.4.1.164.12.3.2.2.3.1.4	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP during this interval. -inProgress(2) has no meaning for an ended interval. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was OK.
atmLoopbackVpIvlTable	1.3.6.1.4.1.164.12.3.2.2.3		not-accessible	This table contains parameters for an OAM VP loopback test, according interval number.
I32 atmLoopbackVpIvlVpi	1.3.6.1.4.1.164.12.3.2.2.3.1.2	Integer32	read-only	The VPI of the OAM VPL.
I32 atmLoopbackVpMaxDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.6	Integer32	read-only	Maximum delay without including lost cells.
I32 atmLoopbackVpMinDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.7	Integer32	read-only	Minimum delay.
INT atmLoopbackVpOperStatus	1.3.6.1.4.1.164.12.3.2.2.1.1.3	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.
atmLoopbackVpTable	1.3.6.1.4.1.164.12.3.2.2.1		not-accessible	This table contains parameters for an OAM VP loopback test.
I32 atmLoopbackVpVpi	1.3.6.1.4.1.164.12.3.2.2.1.1.2	Integer32	read-only	The VPI of the OAM VPL.
atmNte	1.3.6.1.4.1.164.12.3
atmNteAlarmIfEntry	1.3.6.1.4.1.164.12.3.2.1.2.1		not-accessible	An entry in the interface Alarm table.
atmNteAlarmIfTable	1.3.6.1.4.1.164.12.3.2.1.2		not-accessible	The interface Alarm table.
INT atmNteAlarmType	1.3.6.1.4.1.164.12.3.1.2.11	INTEGER	read-only	This object specifies the type of the alarm.
atmNteAlarmVcEntry	1.3.6.1.4.1.164.12.3.2.1.6.1		not-accessible	An entry in the ATM VC Alarm table. ifIndex of the ATM layer.
atmNteAlarmVcTable	1.3.6.1.4.1.164.12.3.2.1.6		not-accessible	The ATM VC Alarm table.
atmNteAlarmVpEntry	1.3.6.1.4.1.164.12.3.2.1.5.1		not-accessible	An entry in the ATM VP Alarm table. ifIndex of the ATM layer.
atmNteAlarmVpTable	1.3.6.1.4.1.164.12.3.2.1.5		not-accessible	The ATM VP Alarm table.
INT atmNteBridgingMode	1.3.6.1.4.1.164.12.3.1.2.7	INTEGER	read-write	Bridging mode can be one of the following: ATM <> Ethernet - Bridging is between the Ethernet port and the ATM port (there is no bridging between VCs). ATM <> Ethernet + ATM - Bridging is done both between the Ethernet port and the ATM port and also between VCs.
INT atmNteCardCmd	1.3.6.1.4.1.164.12.3.1.2.1.1.6	INTEGER	read-write	Command on the card that is installed in the selected slot. The commands are applicable according to the value of atmNteCardStatus. See the specification document for details. deleteConfig - Deletes the card configuration. deactivate - All the connections state will be changed to NotReady. The card configuration will be blocked. activate - Does the same as done upon card insertion: Initiates the relevant parameters, activates the physical layer, ATM layer and logical layer.
INT atmNteCardStatus	1.3.6.1.4.1.164.12.3.1.2.1.1.5	INTEGER	read-only	Status of the card in the selected slot. notActive - Connections are in NotReady state. No configuration is available for the card. The access to the card HW is blocked. This state is relevant for an extracted card, and for a case in which the card was deactivated. active - The module installed and functions. A card that in this state can be configured. inProgress - The status during proccessing of a command from atmNteCardCmd. empty - No information is valid for the selected slot. This status is relevant to a case in which the card configaration was deleted, or in case in which a slot was empty since the device startup.
INT atmNteCardType	1.3.6.1.4.1.164.12.3.1.2.1.1.4	INTEGER	read-only	The card type.
atmNteConfCAC	1.3.6.1.4.1.164.12.3.1.1.10
INT atmNteConfCACMode	1.3.6.1.4.1.164.12.3.1.1.10.1	INTEGER	read-write	CAC support mode. For ACE2002, the following are the applicable values: disable(1), enable(2), 10 - 1000.
atmNteConfIfEntry	1.3.6.1.4.1.164.12.3.2.1.1.1		not-accessible	An entry in the Physical interface configuration table. The ifIndex is of the lowest physical layer.
atmNteConfIfTable	1.3.6.1.4.1.164.12.3.2.1.1		not-accessible	The Physical interface configuration table.
INT atmNteConfLoopbackAddMode	1.3.6.1.4.1.164.12.3.1.1.9.3.1	INTEGER	read-write	Loopback addressing mode. on - will enable loopback addressing. off - will disable loopback addressing.
OCT atmNteConfLoopbackSourceAdd	1.3.6.1.4.1.164.12.3.1.1.9.3.2	OCTET STRING	read-write	Loopback source address. This field is relevant when atmNteConfOamAddMode is on.
atmNteConfOam	1.3.6.1.4.1.164.12.3.1.1.9
atmNteConfOamAddressing	1.3.6.1.4.1.164.12.3.1.1.9.3
INT atmNteConfOamAIS	1.3.6.1.4.1.164.12.3.1.1.9.2.1	INTEGER	read-write	Defines if a F4 segment OAM cell is transmitted due to problems in the other port, i.e. physical layer alarm or F4 defect. This is valid only when the ACE101 has ATM UNI interfaces in both sides and is configured for 'Non-Intrusive' mode. none - AIS is not sent to any of the ports. user - F4 AIS will be sent toward the user when defect is detected in the network port. network - F4 AIS will be sent toward the network when defect is detected in the user port. both - F4 AIS will be sent toward the network when defect is detected in the user port and toward the user when defect is detected in the network port.
INT atmNteConfOamIfAisRdi	1.3.6.1.4.1.164.12.3.1.1.9.4.1.1	INTEGER	read-write	This parameter controls the generation of F4/F5 AIS and RDI due to lower order problems such as physical layer problems. For AIS: Defines if F4/F5 AIS cell is transmitted due to problems such as physical layer alarm or F4/F5 defect. This is applicable for all ports . off - Problems in this port will not trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. on - Problems in this port will trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. For RDI: Defines if F4/F5 RDI cell will be transmitted due to physical layer problems in that port (in addition to F4/F5 RDI cells transmitted due to ATM layer problems). For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4/F5 RDI cell back to the trunk. The type of F4/F5 (Segment or End-to-End) is according to the configuration of the VPC/VCC.
atmNteConfOamIfEntry	1.3.6.1.4.1.164.12.3.1.1.9.4.1		not-accessible	.
atmNteConfOamIfTable	1.3.6.1.4.1.164.12.3.1.1.9.4		not-accessible	OAM support per ATM interface.
INT atmNteConfOamRDI	1.3.6.1.4.1.164.12.3.1.1.9.2.2	INTEGER	read-write	Defines if an F4 OAM RDI cell is transmitted due to physical layer problems in the port (in addition to F4 RDI cells transmitted due to ATM layer problems). The type of F4 RDI (Segment or End-to-End) is according to the ACE-101 OAM mode. For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4 RDI cell back to the trunk.
INT atmNteConfOamSupport	1.3.6.1.4.1.164.12.3.1.1.9.1	INTEGER	read-write	OAM support mode, which determines the device location in a segment wise.
atmNteConfOamTransmission	1.3.6.1.4.1.164.12.3.1.1.9.2
atmNteConfVpEntry	1.3.6.1.4.1.164.12.3.2.1.3.1		not-accessible	An entry in the ATM VP configuration table. ifIndex of the ATM layer.
atmNteConfVpTable	1.3.6.1.4.1.164.12.3.2.1.3		not-accessible	The ATM VP configuration table. The table is an extension to the atmVplTable of RFC-1695.
INT atmNteConnectionsMaxNumber	1.3.6.1.4.1.164.12.3.1.1.19	INTEGER	read-write	The MAX number of connections supported by system. Setting this parameter will affect the number of MAX intervals supported. This parameter will affect the system only after reset. Changing this parameter from high value to a low value, will be accepted by agent only if the actual used connection <= the desired connection Max number. Applicable to ace2002.
I32 atmNteConnectionsNumber	1.3.6.1.4.1.164.12.3.1.2.13	Integer32	read-only	This object specifies a quantity of connections.
I32 atmNteDefaultLoopbackThreshold	1.3.6.1.4.1.164.12.3.1.1.27	Integer32	read-write	The Default OAM Loopback Failure Threshold value that will be used for configuration.
I32 atmNteDefaultVci	1.3.6.1.4.1.164.12.3.1.1.21	Integer32	read-write	Default Vci for management.
I32 atmNteDefaultVpi	1.3.6.1.4.1.164.12.3.1.1.20	Integer32	read-write	Default Vpi for management.
I32 atmNteDPLTCR	1.3.6.1.4.1.164.12.3.1.1.3	Integer32	read-write	The Degraded ES Limit threshold for Performance Management.
I32 atmNteDSESLTCR	1.3.6.1.4.1.164.12.3.1.1.6	Integer32	read-write	The Degraded ES Limit threshold for Performance Management.
atmNteEvents	1.3.6.1.4.1.164.12.3.0			The events for RAD ATM products.
INT atmNteEventType	1.3.6.1.4.1.164.12.3.1.2.9	INTEGER	read-only	This parameter identifies the event. On - the problem exist. Off - the problem not exist. InvalidLogin - Invalid login on local console. CorrectLogin - Successful login operation.
I32 atmNteGranularityFactor	1.3.6.1.4.1.164.12.3.1.1.29	Integer32	read-write	This parameter affects the granularity of the guaranteed Rate (SCR+MCR) in spaced connection (cell/sec units). It is also defines the minimum guaranteed rate in spaced connection.
I32 atmNteHostAtmIfIndex	1.3.6.1.4.1.164.12.3.1.1.11.1.4	Integer32	read-create	ATM interface index. Will be 1 for user port, and 2 for network port.
IP atmNteHostDefaultNextHop	1.3.6.1.4.1.164.12.3.1.1.11.1.10	IpAddress	read-create	The host interface Default Next Hop address. This address will be used as default next hop for every Bundle mapped to this Host.
I32 atmNteHostDefaultVlanID	1.3.6.1.4.1.164.12.3.1.1.11.1.12	Integer32	read-create	Default VLAN ID of this Host.
I32 atmNteHostDefaultVlanPriority	1.3.6.1.4.1.164.12.3.1.1.11.1.13	Integer32	read-create	Default VLAN priority for this Host.
atmNteHostIfEntry	1.3.6.1.4.1.164.12.3.1.1.11.1		not-accessible	.
atmNteHostIfTable	1.3.6.1.4.1.164.12.3.1.1.11		not-accessible	Host IP interface table.
IP atmNteHostIP	1.3.6.1.4.1.164.12.3.1.1.11.1.2	IpAddress	read-create	The host interface IP address.
IP atmNteHostMask	1.3.6.1.4.1.164.12.3.1.1.11.1.3	IpAddress	read-create	The host interface subnet mask.
I32 atmNteHostPvcIndex	1.3.6.1.4.1.164.12.3.1.1.11.1.1	Integer32	read-only	A PVC index. The range is 1..10.
I32 atmNteHostRdnVci	1.3.6.1.4.1.164.12.3.1.1.11.1.9	Integer32	read-create	The VCI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).
I32 atmNteHostRdnVpi	1.3.6.1.4.1.164.12.3.1.1.11.1.8	Integer32	read-create	The VPI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).
ROW atmNteHostRowStatus	1.3.6.1.4.1.164.12.3.1.1.11.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
I32 atmNteHostVci	1.3.6.1.4.1.164.12.3.1.1.11.1.6	Integer32	read-create	VCI of the PVC connected to that host interface.
INT atmNteHostVlanTagging	1.3.6.1.4.1.164.12.3.1.1.11.1.11	INTEGER	read-create	VLAN Tag support. no - No support to VLAN. yes - 4 VLAN bytes will be added to each frame connected to this Host.
I32 atmNteHostVpi	1.3.6.1.4.1.164.12.3.1.1.11.1.5	Integer32	read-create	VPI of the PVC connected to that host interface.
atmNteIdEntry	1.3.6.1.4.1.164.12.3.1.2.1.1		not-accessible	.
I32 atmNteIdIndex	1.3.6.1.4.1.164.12.3.1.2.1.1.1	Integer32	read-only	An Index of the Unit ID table. The following units have IDs in this table: 1 - System 2 - ATM Board 3 - User Card 4 - Trunk 1 card 5 - Trunk 2 card 6 - Shaper 7 - Clock Unit 8 - Slot 1 card 9 - Slot 2 card 10 - Slot 3 card 11 - Slot 4 card 12 - Fan1 13 - Fan2 14 - Control Unit.
atmNteIdTable	1.3.6.1.4.1.164.12.3.1.2.1		not-accessible	The IDs of the cards and of the system.
I32 atmNteIntervalMaxNumber	1.3.6.1.4.1.164.12.3.1.2.10	Integer32	read-only	The MAX number of connections intervals supported by system. This parameter value is a function of atmNteConnectionsMaxNumber parameter. This parameter should affect the threshold values selected by user. Applicable to ace2002.
INT atmNteLevel	1.3.6.1.4.1.164.12.3.1.2.12	INTEGER	read-only	This object specifies the ATM level.
atmNteLoopback	1.3.6.1.4.1.164.12.3.2.2
I32 atmNteLoopbackTimeout	1.3.6.1.4.1.164.12.3.1.1.25	Integer32	read-write	The Loopback state timeout in minutes. A value of zero means no timeout (for ever). Default is 5 min.
OCT atmNteManagerAlarmTrapMask	1.3.6.1.4.1.164.12.3.1.1.1.1.12	OCTET STRING	read-create	The value of this object determines the alarm traps that the agent should mask and not send to this NMS. The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. More details on the masked traps exist in the product specification. For products that do not mask specific traps, the value of the bits will be 0.
I32 atmNteManagerConfigPorts	1.3.6.1.4.1.164.12.3.1.1.1.1.13	Integer32	read-create	This variable defines from which port/s this manager can configure the device. For IPmux 11 the value of this variable will be according to the ports combination: Network =1 User1=2 User2=4 (For Example: All ports = 7).
atmNteManagerEntry	1.3.6.1.4.1.164.12.3.1.1.1.1		not-accessible	A single manager and the PVC for receiving traps.
I32 atmNteManagerIfIndex	1.3.6.1.4.1.164.12.3.1.1.1.1.3	Integer32	read-create	The ATM interface index of the management port.
IP atmNteManagerIP	1.3.6.1.4.1.164.12.3.1.1.1.1.1	IpAddress	read-only	The IP address of the NMS.
IP atmNteManagerNextHop	1.3.6.1.4.1.164.12.3.1.1.1.1.8	IpAddress	read-create	This parameter is relevant to Ethernet out of band host only (PVC=10). The Next Hop IP address of the entry route.
I32 atmNteManagerPvc	1.3.6.1.4.1.164.12.3.1.1.1.1.2	Integer32	read-only	A PVC index. The range is 1..8. There are four PVCs on the User Port and four PVCs on the Network Port. The default VPI, VCI values are specified below.
ROW atmNteManagerRowStatus	1.3.6.1.4.1.164.12.3.1.1.1.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
atmNteManagerTable	1.3.6.1.4.1.164.12.3.1.1.1		not-accessible	The Manager Table includes all the NMSs that receive traps from this agent. A single manager can receive traps on more than one PVC. The agent will set implicitly the correct ifIndex, VPI, VCI values to all relevant entries in the table when the user changes them for one of the PVCs.
I32 atmNteManagerTrapMask	1.3.6.1.4.1.164.12.3.1.1.1.1.6	Integer32	read-create	The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
I32 atmNteManagerVci	1.3.6.1.4.1.164.12.3.1.1.1.1.5	Integer32	read-create	The VCI of the management VCL. Defaults: 32,33,34,35.
I32 atmNteManagerVlanFramePriority	1.3.6.1.4.1.164.12.3.1.1.1.1.11	Integer32	read-create	VLAN Frame priority.Range is 0..7.
I32 atmNteManagerVlanIdentifier	1.3.6.1.4.1.164.12.3.1.1.1.1.10	Integer32	read-create	VLAN ID. Range is 0..4095.
INT atmNteManagerVlanSupport	1.3.6.1.4.1.164.12.3.1.1.1.1.9	INTEGER	read-create	VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
I32 atmNteManagerVpi	1.3.6.1.4.1.164.12.3.1.1.1.1.4	Integer32	read-create	The VPI of the management VCL. Default: 0.
I32 atmNteMaxBurstSize	1.3.6.1.4.1.164.12.3.1.1.28	Integer32	read-write	The Maximum allowed burst size (cell units). This object is applicable for each Physical port.
atmNteMdl	1.3.6.1.4.1.164.12.3.3
atmNteMdlConfig	1.3.6.1.4.1.164.12.3.3.1
atmNteMdlConfigEntry	1.3.6.1.4.1.164.12.3.3.1.1.1		not-accessible	There is an entry in this table just for those modules that have parameters that are relevant to module level only.
atmNteMdlConfigTable	1.3.6.1.4.1.164.12.3.3.1.1		not-accessible	Module configuration table.
INT atmNteMdlInputPriorityMechanism	1.3.6.1.4.1.164.12.3.3.1.1.1.3	INTEGER	read-write	This object allows the user to Enable/Disable the Input priority mechanism. This object is applicable for modules with more than one port, in which the total ports input may be greater than the port output. disabled - all LAN VCCs will be transmitted through the same queue (queue 1). Upon congestion frames will be dropped randomly. enabled - the user should configure each port/connection priority. Upon congestion frames will be dropped according to priority.
INT atmNteMdlPrtCpuSharing	1.3.6.1.4.1.164.12.3.3.1.1.1.2	INTEGER	read-write	This object lets the user decide what will be the CPU sharing between the ports of the module. This object is applicable for modules in which the same CPU handles the traffic of all ports. equal - All ports will have the same CPU resource. port1 - Port 1 will have higher priority than the other ports.
I32 atmNteMdlSlotIndex	1.3.6.1.4.1.164.12.3.3.1.1.1.1	Integer32	not-accessible	The slot number.
INT atmNteOamCellType	1.3.6.1.4.1.164.12.3.1.1.26.1.2	INTEGER	read-only	This object indicates a unique Indication Signal. aisAndRdi(1) - Alarm Indication Signal (AIS) and Remote Defect Indication (RDI) cell. loopback(2) - Loopback cell.
INT atmNteOamEnable	1.3.6.1.4.1.164.12.3.1.1.26.1.4	INTEGER	read-write	This parameter determines if the specified OAM cells will be enabled.
atmNteOamEntry	1.3.6.1.4.1.164.12.3.1.1.26.1		not-accessible	An entry in the OAM table. Each entry in this table will indicate a special OAM.
INT atmNteOamLevel	1.3.6.1.4.1.164.12.3.1.1.26.1.3	INTEGER	read-only	The level of the OAM cell. -- f4 (2) - VP level, f5 (3) - VC level.
INT atmNteOamMode	1.3.6.1.4.1.164.12.3.1.1.26.1.1	INTEGER	read-only	The OAM cell path. endToEnd(1) - the entire path.
atmNteOamTable	1.3.6.1.4.1.164.12.3.1.1.26		not-accessible	This table is a static table, which is created by agent once upon initialization. The created entries are actually, only the supported OAM features. This table enables addition of new features by adding new entries rather than adding scalar parameters. An OAM feature is defined by the indexes values combination.
I32 atmNteOutputRate	1.3.6.1.4.1.164.12.3.1.1.13	Integer32	read-write	Aggregate shaping output rate in Cells per Seconds units. Default value is the Network port rate.
INT atmNtePlugAndPlayActivity	1.3.6.1.4.1.164.12.3.1.1.17	INTEGER	read-write	Activity control for Manager Plug And Play. disable - disable the feature. offline - Automatic learn IP address into offline memory. online - Automatic learn IP address into online memory.
NUM atmNtePlugAndPlayIfIndex	1.3.6.1.4.1.164.12.3.1.1.24	InterfaceIndex	read-write	The ifIndex of the Plug and Play VCC.
atmNtePM	1.3.6.1.4.1.164.12.3.2.3
INT atmNteProgCardType	1.3.6.1.4.1.164.12.3.1.2.1.1.7	INTEGER	read-write	The programmed card type.
atmNteProtection	1.3.6.1.4.1.164.12.3.1.1.8
INT atmNteProtectionMode	1.3.6.1.4.1.164.12.3.1.1.8.1	INTEGER	read-write	Protection Mode. MspOn - Multiplex section protection. pathOn - High order path protection. mspUniOn - Multiplex section Uni-directional protection. mspOneToN - Multiplex section protection.
INT atmNteProtectionSwitchLink	1.3.6.1.4.1.164.12.3.1.1.8.3	INTEGER	read-write	ForceSwitch - will force Switching from the working link to the backup link. Afterwards the agent will set atmNteProtectionSwitchLink back to off(1). atmNteProtectionMode must be either mspOn or pathOn.
INT atmNteProtectionWorkingLink	1.3.6.1.4.1.164.12.3.1.1.8.2	INTEGER	read-write	Selects the working link when atmNteProtectionMode is off.
atmNtePrt	1.3.6.1.4.1.164.12.3.2
atmNtePrtConfig	1.3.6.1.4.1.164.12.3.2.1
INT atmNteQosMode	1.3.6.1.4.1.164.12.3.1.1.37	INTEGER	read-write	This variable defines the QoS Mode. disable(1) - QoS is disabled. multipleVc(2) - QoS is enabled and multiple VCs can be bound per bridge port. singleVc(3) - QoS is enabled and only single VC can be bound per bridge port.
INT atmNteRdnManagement	1.3.6.1.4.1.164.12.3.1.1.23	INTEGER	read-only	The redundancy management status.
I32 atmNteReservedVpi	1.3.6.1.4.1.164.12.3.1.1.22	Integer32	read-write	Internal use VPI, where shaperMode=vpInbandMng.
INT atmNteShaperMode	1.3.6.1.4.1.164.12.3.1.1.12	INTEGER	read-write	Shaper Mode. vpInbandMng - Vcc within a Vp for management.
INT atmNteSlotUsage	1.3.6.1.4.1.164.12.3.1.1.18	INTEGER	read-write	Applicable to ace2002. Slot 2 might be configured as user slot or as network slot.
atmNteSys	1.3.6.1.4.1.164.12.3.1
atmNteSysConfig	1.3.6.1.4.1.164.12.3.1.1
atmNteSysInfo	1.3.6.1.4.1.164.12.3.1.2
INT atmNteSysLogClearAll	1.3.6.1.4.1.164.12.3.1.1.4	INTEGER	read-write	Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).
OCT atmNteTosHighPriority	1.3.6.1.4.1.164.12.3.1.1.16	OCTET STRING	read-write	Priorities options are High or Low. High priority will be represented by bit = 1. Low priority will be represented by bit = 0. Each TOS value will be represented by the bit location. For example, the string for TOS 2, 9, 15 with High priority, will be: \|0000 0000\|... ...\|0000 0000\|1000 0010\|0000 0100\| ...98 7654 3210 (Bit #) 8 ... 3 2 1 (Byte #).
OCT atmNteTosMask	1.3.6.1.4.1.164.12.3.1.1.15	OCTET STRING	read-write	This parameter determines the seqence of bits that will be used for TOS. For ACE101 this parameter is applicable only if atmNteTosMode = enable. Valid only for IP-TOS process.
INT atmNteTosMode	1.3.6.1.4.1.164.12.3.1.1.14	INTEGER	read-write	TOS Mode.
I32 atmNteTotalCc	1.3.6.1.4.1.164.12.3.1.2.15	Integer32	read-only	This parameter counts the total number of end-points that were configured with Continuity Check (CC).
I32 atmNteTotalInputRate	1.3.6.1.4.1.164.12.3.1.1.30	Integer32	read-only	This parameter indicates the total input rate of the device in cells/sec.
I32 atmNteTotalLb	1.3.6.1.4.1.164.12.3.1.2.14	Integer32	read-only	This parameter counts the total number of end-points that were configured with Loopback (LB).
I32 atmNteTotalOutputRate	1.3.6.1.4.1.164.12.3.1.1.31	Integer32	read-only	This parameter indicates the total output rate of the device in cells/sec.
I32 atmNteTotalPm	1.3.6.1.4.1.164.12.3.1.2.16	Integer32	read-only	This parameter counts the total number of end-points that were configured with PM.
I32 atmNteUnitId	1.3.6.1.4.1.164.12.3.1.2.1.1.2	Integer32	read-only	The ID of the Unit. For index = 6, the id will describe the validity of a shaper in the system: 0 - Shaper Not exist 1 - Shaper exist. For index = 7, the id will describe the validity of a clock in the system: 0 - Clock Not exist 1 - Clock exist. 2- Clock exist but failed. For index = 12,13 the id will describe the functionality of a FAN1 : 0 - OK 1 - Failed.
STR atmNteUnitVersion	1.3.6.1.4.1.164.12.3.1.2.1.1.3	DisplayString	read-only	Hardware and Software version of the module.
I32 atmNteUPLTCR	1.3.6.1.4.1.164.12.3.1.1.2	Integer32	read-write	The Unacceptable ES Limit threshold for Performance Management.
I32 atmNteUSESLTCR	1.3.6.1.4.1.164.12.3.1.1.5	Integer32	read-write	The Unacceptable SES Limit threshold for Performance Management.
I32 atmNteVcActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.6.1.3	Integer32	read-only	A Bit String of the active alarms on this VC. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VC AIS 2 - VC Loss Of Continuity 3 - VC RDI 4 - VC Errored Cells > Threshold 5 - VC Lost Cells > Threshold 6 - VC Misinserted Cells > Threshold 7 - Tx VC AIS 8 - Tx VC RDI 9 - VC Loopback Failure
I32 atmNteVcAlarmVci	1.3.6.1.4.1.164.12.3.2.1.6.1.2	Integer32	read-only	The VCI of the VC on which there is an active alarm.
I32 atmNteVcAlarmVpi	1.3.6.1.4.1.164.12.3.2.1.6.1.1	Integer32	read-only	The VPI of the VC on which there is an active alarm.
I32 atmNteVpActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.5.1.2	Integer32	read-only	A Bit String of the active alarms on this VP. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VP AIS 2 - VP Loss Of Continuity 3 - VP RDI Reception 4 - VP Errored Cells > Threshold 5 - VP Lost Cells > Threshold 6 - VP Misinserted Cells > Threshold 9 - VP Loopback Failure
I32 atmNteVpAlarmVpi	1.3.6.1.4.1.164.12.3.2.1.5.1.1	Integer32	read-only	The VPI on which there is an active alarm.
atmPerfHistory	1.3.6.1.4.1.164.12.2.1
atmPvcPerformance	1.3.6.1.4.1.164.12.2.1.2
atmSysConfigCellTest	1.3.6.1.4.1.164.12.3.1.1.33
INT atmSysConfigCellTestClp	1.3.6.1.4.1.164.12.3.1.1.33.5	INTEGER	read-write	The type of the Cell.
INT atmSysConfigCellTestOamType	1.3.6.1.4.1.164.12.3.1.1.33.6	INTEGER	read-write	The OAM type of the Cell. This object is applicable if atmSysConfigCellTestPti = oamSegment/oamEndToEnd .
OCT atmSysConfigCellTestPayload	1.3.6.1.4.1.164.12.3.1.1.33.7	OCTET STRING	read-write	The payload of the cell. For OAM cell the payload is set automatically to 6A.
NUM atmSysConfigCellTestPort	1.3.6.1.4.1.164.12.3.1.1.33.1	InterfaceIndex	read-write	An Index of the port on which the cell test will be sent.
INT atmSysConfigCellTestPti	1.3.6.1.4.1.164.12.3.1.1.33.4	INTEGER	read-write	The cell type.
I32 atmSysConfigCellTestQuantity	1.3.6.1.4.1.164.12.3.1.1.33.8	Integer32	read-write	Quantity of cells to send.
INT atmSysConfigCellTestSendCmd	1.3.6.1.4.1.164.12.3.1.1.33.9	INTEGER	read-write	Setting the variable to send(3) perfroms cell test. The agent will immediately reset the variable to off(2).
I32 atmSysConfigCellTestVci	1.3.6.1.4.1.164.12.3.1.1.33.3	Integer32	read-write	The VCI on which the cell test will be sent.
I32 atmSysConfigCellTestVpi	1.3.6.1.4.1.164.12.3.1.1.33.2	Integer32	read-write	The VPI on which the cell test will be sent.
G32 atmSysCurrentCdc	1.3.6.1.4.1.164.12.3.1.2.8.1	Gauge32	read-only	Seconds in which cells dropped was occured in the current 15 minutes interval.
I32 atmSysFanUnits	1.3.6.1.4.1.164.12.3.1.2.4	Integer32	read-only	The number of fan units.
G32 atmSysIntervalCdc	1.3.6.1.4.1.164.12.3.1.2.8.2.1.2	Gauge32	read-only	Seconds in which cells dropped was occured in 15 minutes interval.
atmSysIntervalEntry	1.3.6.1.4.1.164.12.3.1.2.8.2.1		not-accessible	.
I32 atmSysIntervalNumber	1.3.6.1.4.1.164.12.3.1.2.8.2.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
atmSysIntervalTable	1.3.6.1.4.1.164.12.3.1.2.8.2		not-accessible	The system level Interval table.
INT atmSysNetPrtInUse	1.3.6.1.4.1.164.12.3.1.2.6	INTEGER	read-only	The network port in use.
I32 atmSysNetPrts	1.3.6.1.4.1.164.12.3.1.2.5	Integer32	read-only	The number of network ports.
I32 atmSysPSunits	1.3.6.1.4.1.164.12.3.1.2.2	Integer32	read-only	The number of power supply units.
INT atmSysPSunitsInUse	1.3.6.1.4.1.164.12.3.1.2.3	INTEGER	read-only	The main power supply in this unit.
atmSysStats	1.3.6.1.4.1.164.12.3.1.2.8
I32 atmThresholdErroredCells	1.3.6.1.4.1.164.12.3.2.1.2.1.7	Integer32	read-write	When Errored Cells are greater than this threshold, an active alarm is raised.
I32 atmThresholdLineBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.3	Integer32	read-write	When Line BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
I32 atmThresholdLineFEBE	1.3.6.1.4.1.164.12.3.2.1.2.1.4	Integer32	read-write	When Line FEBEs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
I32 atmThresholdLostCells	1.3.6.1.4.1.164.12.3.2.1.2.1.8	Integer32	read-write	When Lost Cells are greater than this threshold, an active alarm is raised.
I32 atmThresholdMisinsertedCells	1.3.6.1.4.1.164.12.3.2.1.2.1.9	Integer32	read-write	When Misinserted Cells are greater than this threshold, an active alarm is raised.
I32 atmThresholdPathBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.5	Integer32	read-write	When Path BIPs are greater than this threshold, an active alarm is raised.
I32 atmThresholdPathFEBE	1.3.6.1.4.1.164.12.3.2.1.2.1.6	Integer32	read-write	When Path FEBEs are greater than this threshold, an active alarm is raised.
I32 atmThresholdSectionBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.2	Integer32	read-write	When Section BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
INT atmTrafficDescrParamMode	1.3.6.1.4.1.164.12.3.1.1.38.1.1	INTEGER	read-create	The Mode of the Traffic Descriptor.
atmTrafficDescrParamXEntry	1.3.6.1.4.1.164.12.3.1.1.38.1		not-accessible	An entry in the table.
atmTrafficDescrParamXTable	1.3.6.1.4.1.164.12.3.1.1.38		not-accessible	An Augment to ATM Traffic Descriptor Parameter Table (atmTrafficDescrParamTable in ATM-MIB; RFC-2515).
atmVcCrossConnectExtenEntry	1.3.6.1.4.1.164.12.3.1.1.35.1		not-accessible	An entry in the table.
atmVcCrossConnectExtenTable	1.3.6.1.4.1.164.12.3.1.1.35		not-accessible	An extension to the ATM VC Cross Connect table (RFC2515 - atmVcCrossConnectTable).
STR atmVcCrossConnectName	1.3.6.1.4.1.164.12.3.1.1.35.1.1	SnmpAdminString	read-create	The Connection's name.
G32 atmVcCurrentCDC	1.3.6.1.4.1.164.12.2.1.2.2.1.1.14	Gauge32	read-only	Amount of cells dropped in the current 15 minute interval of the VC connection.
G32 atmVcCurrentClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVcCurrentClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.16	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVcCurrentContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.2.1.1.11	Gauge32	read-only	The counter associated with the number of loss of continuity cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
atmVcCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.2.1.1		not-accessible	An entry in the ATM VC Current table.
G32 atmVcCurrentGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.2.1.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.2.1.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentMCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.22	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second).
G32 atmVcCurrentPCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.20	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second).
G32 atmVcCurrentRxAIS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.7	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.2.1.1.4	Gauge32	read-only	The counter associated with the number of received cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.2.1.1.3	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentRxRDI	1.3.6.1.4.1.164.12.2.1.2.2.1.1.9	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentSCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.21	Gauge32	read-only	The average traffic rate during the last interval of the VC connection.
G32 atmVcCurrentSES	1.3.6.1.4.1.164.12.2.1.2.2.1.1.13	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.24	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVcCurrentShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.25	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
G32 atmVcCurrentShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.23	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
atmVcCurrentTable	1.3.6.1.4.1.164.12.2.1.2.2.1		not-accessible	The ATM VC Current table.
G32 atmVcCurrentTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.19	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVcCurrentTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVcCurrentTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.15	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVcCurrentTxAIS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.8	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.
G32 atmVcCurrentTxRDI	1.3.6.1.4.1.164.12.2.1.2.2.1.1.10	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.12	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
I32 atmVcCurrentVci	1.3.6.1.4.1.164.12.2.1.2.2.1.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.2.1.1.1	Integer32	read-only	The VPI of the VCL.
G32 atmVcIntervalCDC	1.3.6.1.4.1.164.12.2.1.2.2.3.1.15	Gauge32	read-only	Amount of cells dropped in the 15 minute interval of the VC connection.
G32 atmVcIntervalClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.19	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVcIntervalClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.17	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVcIntervalContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.2.3.1.12	Gauge32	read-only	The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
atmVcIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.2.3.1		not-accessible	An entry in the ATM Vc Interval table.
G32 atmVcIntervalGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.2.3.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.2.3.1.7	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalMCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.23	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
I32 atmVcIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.2.3.1.3	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmVcIntervalPCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.21	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxAIS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.8	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.2.3.1.5	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.2.3.1.4	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxRDI	1.3.6.1.4.1.164.12.2.1.2.2.3.1.10	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalSCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.22	Gauge32	read-only	The average traffic rate during the last interval of the VC connection, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalSES	1.3.6.1.4.1.164.12.2.1.2.2.3.1.14	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.25	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVcIntervalShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.26	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
G32 atmVcIntervalShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.24	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
atmVcIntervalTable	1.3.6.1.4.1.164.12.2.1.2.2.3		not-accessible	The ATM Vc Interval table.
G32 atmVcIntervalTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.20	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVcIntervalTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVcIntervalTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.16	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVcIntervalTxAIS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.9	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.
G32 atmVcIntervalTxRDI	1.3.6.1.4.1.164.12.2.1.2.2.3.1.11	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.13	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
I32 atmVcIntervalVci	1.3.6.1.4.1.164.12.2.1.2.2.3.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.2.3.1.1	Integer32	read-only	The VPI of the VCL.
atmVcPerformance	1.3.6.1.4.1.164.12.2.1.2.2
INT atmVcPmAdminStatus	1.3.6.1.4.1.164.12.3.2.3.2.1.4	INTEGER	read-create	up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .
I32 atmVcPmBlockSize	1.3.6.1.4.1.164.12.3.2.3.2.1.6	Integer32	read-create	Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.
I32 atmVcPMCurrentDir	1.3.6.1.4.1.164.12.2.1.2.2.2.1.3	Integer32	read-only	The direction of Performance Management.
G32 atmVcPMCurrentECB	1.3.6.1.4.1.164.12.2.1.2.2.2.1.11	Gauge32	read-only	The counter associated with the number of ECBs encountered by the VCL of this ATM interface in the current 15 minute interval.
atmVcPMCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.2.2.1		not-accessible	An entry in the ATM VC Current table for Performance Management.
G32 atmVcPMCurrentErroredCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.8	Gauge32	read-only	The counter associated with the number of errored cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentES	1.3.6.1.4.1.164.12.2.1.2.2.2.1.13	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
INT atmVcPMCurrentIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.2.2.1.16	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVcPMCurrentLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.2.2.1.17	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
G32 atmVcPMCurrentLostCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.9	Gauge32	read-only	The counter associated with the number of lost cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.10	Gauge32	read-only	The counter associated with the number of misinserted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentRxClp0	1.3.6.1.4.1.164.12.2.1.2.2.2.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentRxClp01	1.3.6.1.4.1.164.12.2.1.2.2.2.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentSECB	1.3.6.1.4.1.164.12.2.1.2.2.2.1.12	Gauge32	read-only	The counter associated with the number of SECBs encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentSES	1.3.6.1.4.1.164.12.2.1.2.2.2.1.14	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
atmVcPMCurrentTable	1.3.6.1.4.1.164.12.2.1.2.2.2		not-accessible	The ATM VC Current table for Performance Management.
G32 atmVcPMCurrentTxClp0	1.3.6.1.4.1.164.12.2.1.2.2.2.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentTxClp01	1.3.6.1.4.1.164.12.2.1.2.2.2.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.2.2.1.15	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
I32 atmVcPMCurrentVci	1.3.6.1.4.1.164.12.2.1.2.2.2.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcPMCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.2.2.1.1	Integer32	read-only	The VPI of the VCL.
INT atmVcPmDirection	1.3.6.1.4.1.164.12.3.2.3.2.1.5	INTEGER	read-create	The direction of PM.
atmVcPmEntry	1.3.6.1.4.1.164.12.3.2.3.2.1		not-accessible	An entry in table.
I32 atmVcPmIfIndex	1.3.6.1.4.1.164.12.3.2.3.2.1.1	Integer32	read-only	The interface index of the ATM layer.
INT atmVcPMIntervalDir	1.3.6.1.4.1.164.12.2.1.2.2.4.1.3	INTEGER	read-only	The direction of Performance Management.
G32 atmVcPMIntervalECB	1.3.6.1.4.1.164.12.2.1.2.2.4.1.12	Gauge32	read-only	The counter associated with the number of ECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
atmVcPMIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.2.4.1		not-accessible	An entry in the ATM Vc Interval table for Performance Management.
G32 atmVcPMIntervalErroredCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.9	Gauge32	read-only	The counter associated with the number of Errored cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalES	1.3.6.1.4.1.164.12.2.1.2.2.4.1.14	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
INT atmVcPMIntervalLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.2.4.1.18	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
G32 atmVcPMIntervalLostCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.10	Gauge32	read-only	The counter associated with the number of Lost cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.11	Gauge32	read-only	The counter associated with the number of Misinserted cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
I32 atmVcPMIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.2.4.1.4	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
INT atmVcPMIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.2.4.1.17	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
G32 atmVcPMIntervalRxClp0	1.3.6.1.4.1.164.12.2.1.2.2.4.1.8	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalRxClp01	1.3.6.1.4.1.164.12.2.1.2.2.4.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalSECB	1.3.6.1.4.1.164.12.2.1.2.2.4.1.13	Gauge32	read-only	The counter associated with the number of SECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalSES	1.3.6.1.4.1.164.12.2.1.2.2.4.1.15	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
atmVcPMIntervalTable	1.3.6.1.4.1.164.12.2.1.2.2.4		not-accessible	The ATM Vc Interval table for Performance Management.
G32 atmVcPMIntervalTxClp0	1.3.6.1.4.1.164.12.2.1.2.2.4.1.6	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalTxClp01	1.3.6.1.4.1.164.12.2.1.2.2.4.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.2.4.1.16	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
I32 atmVcPMIntervalVci	1.3.6.1.4.1.164.12.2.1.2.2.4.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcPMIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.2.4.1.1	Integer32	read-only	The VPI of the VCL.
G32 atmVcPMQoSCER	1.3.6.1.4.1.164.12.2.1.2.2.7.1.4	Gauge32	read-only	Cell Error Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVcPMQoSCLR	1.3.6.1.4.1.164.12.2.1.2.2.7.1.3	Gauge32	read-only	Cell Loss Ratio counter for the reference period (atmVcPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVcPMQoSCMR	1.3.6.1.4.1.164.12.2.1.2.2.7.1.5	Gauge32	read-only	Cell Miss-insertion Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .
INT atmVcPMQoSDirection	1.3.6.1.4.1.164.12.2.1.2.2.7.1.1	INTEGER	read-only	The direction of performance management.
atmVcPMQoSEntry	1.3.6.1.4.1.164.12.2.1.2.2.7.1		not-accessible	An entry in the VC PM QoS table.
INT atmVcPMQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.2.7.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
atmVcPMQoSTable	1.3.6.1.4.1.164.12.2.1.2.2.7		not-accessible	The PM VC QoS table.
ROW atmVcPmRowStatus	1.3.6.1.4.1.164.12.3.2.3.2.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
INT atmVcPmSink	1.3.6.1.4.1.164.12.3.2.3.2.1.8	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
INT atmVcPmSource	1.3.6.1.4.1.164.12.3.2.3.2.1.9	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
atmVcPmTable	1.3.6.1.4.1.164.12.3.2.3.2		not-accessible	This table contains parameters for VC performance monitoring.
I32 atmVcPmVci	1.3.6.1.4.1.164.12.3.2.3.2.1.3	Integer32	read-only	The VCI of the PM VCL.
I32 atmVcPmVpi	1.3.6.1.4.1.164.12.3.2.3.2.1.2	Integer32	read-only	The VPI of the Performance Monitoring VCL.
I32 atmVcQoSElapsedTime	1.3.6.1.4.1.164.12.2.1.2.2.6.1.2	Integer32	read-only	Elapsed Time in seconds. - for atmVcQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVcQoSPeriodRef = lastPeriod: The value of atmVcQoSElapsedTime when last systemResetAllStatsCmd was received.
atmVcQoSEntry	1.3.6.1.4.1.164.12.2.1.2.2.6.1		not-accessible	An entry in the ATM VP table.
INT atmVcQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.2.6.1.1	INTEGER	read-only	This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
atmVcQoSTable	1.3.6.1.4.1.164.12.2.1.2.2.6		not-accessible	The ATM VP QoS table.
G32 atmVcQoSUAS	1.3.6.1.4.1.164.12.2.1.2.2.6.1.3	Gauge32	read-only	Number of Unavailable Seconds for the reference period (atmVcQoSPeriodRef).
C32 atmVcShaperDiscarded	1.3.6.1.4.1.164.12.2.1.2.2.8.1.1	Counter32	read-only	The number of Cells that were discarded in the shaper on that VCC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.
C32 atmVcShaperEpdDropped	1.3.6.1.4.1.164.12.2.1.2.2.8.1.5	Counter32	read-only	The number of Cells that were dropped in the shaper on that VCC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VC only.
INT atmVcShaperLevel	1.3.6.1.4.1.164.12.2.1.2.2.8.1.4	INTEGER	read-only	The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VCC.
I32 atmVcShaperMaxOccupation	1.3.6.1.4.1.164.12.2.1.2.2.8.1.3	Integer32	read-only	The Maximum number of Cells that were stored in the buffer, since this VC was activated. This parameter is limited to 20 bits.
I32 atmVcShaperOccupation	1.3.6.1.4.1.164.12.2.1.2.2.8.1.2	Integer32	read-only	The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.
atmVcShaperStatEntry	1.3.6.1.4.1.164.12.2.1.2.2.8.1		not-accessible	An entry in the ATM VC shaper statistics table.
atmVcShaperStatTable	1.3.6.1.4.1.164.12.2.1.2.2.8		not-accessible	The ATM VC shaper statistics table.
C32 atmVcShaperTotalEpdDropped	1.3.6.1.4.1.164.12.2.1.2.2.8.1.6	Counter32	read-only	The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VC only.
atmVpCrossConnectExtenEntry	1.3.6.1.4.1.164.12.3.1.1.34.1		not-accessible	An entry in the table.
atmVpCrossConnectExtenTable	1.3.6.1.4.1.164.12.3.1.1.34		not-accessible	An extension to the ATM VP Cross Connect table (RFC2515 - atmVpCrossConnectTable).
STR atmVpCrossConnectName	1.3.6.1.4.1.164.12.3.1.1.34.1.1	SnmpAdminString	read-create	The Connection's name.
G32 atmVpCurrentCDC	1.3.6.1.4.1.164.12.2.1.2.1.1.1.13	Gauge32	read-only	Amount of cells dropped in the current 15 minute interval of the VP connection.
G32 atmVpCurrentClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVpCurrentClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.15	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 and discarded by the traffic policing entity.
G32 atmVpCurrentContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.1.1.1.10	Gauge32	read-only	The counter associated with the number of loss of continuity cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
atmVpCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.1.1.1		not-accessible	An entry in the ATM VP Current table.
G32 atmVpCurrentGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.1.1.1.4	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.1.1.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentMCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.21	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second).
G32 atmVpCurrentPCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.19	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second).
G32 atmVpCurrentRxAIS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.6	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.1.1.1.3	Gauge32	read-only	The counter associated with the number of received cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.1.1.1.2	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentRxRDI	1.3.6.1.4.1.164.12.2.1.2.1.1.1.8	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentSCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.20	Gauge32	read-only	The average traffic rate during the last interval of the VP connection.
G32 atmVpCurrentSES	1.3.6.1.4.1.164.12.2.1.2.1.1.1.12	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.23	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVpCurrentShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.24	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
G32 atmVpCurrentShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.22	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
atmVpCurrentTable	1.3.6.1.4.1.164.12.2.1.2.1.1		not-accessible	The ATM VP Current table.
G32 atmVpCurrentTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.18	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVpCurrentTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.16	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVpCurrentTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.14	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVpCurrentTxAIS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.7	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.
G32 atmVpCurrentTxRDI	1.3.6.1.4.1.164.12.2.1.2.1.1.1.9	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.11	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
I32 atmVpCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.1.1.1.1	Integer32	read-only	The VPI of the VPL.
G32 atmVpIntervalCDC	1.3.6.1.4.1.164.12.2.1.2.1.3.1.14	Gauge32	read-only	Amount of cells dropped in the 15 minute interval of the VP connection.
G32 atmVpIntervalClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVpIntervalClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.16	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVpIntervalContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.1.3.1.11	Gauge32	read-only	The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
atmVpIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.1.3.1		not-accessible	An entry in the ATM Vp Interval table.
G32 atmVpIntervalGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.1.3.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.1.3.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalMCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.22	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
I32 atmVpIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.1.3.1.2	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmVpIntervalPCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.20	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxAIS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.7	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.1.3.1.4	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.1.3.1.3	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxRDI	1.3.6.1.4.1.164.12.2.1.2.1.3.1.9	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalSCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.21	Gauge32	read-only	The average traffic rate during the last interval of the VP connection , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalSES	1.3.6.1.4.1.164.12.2.1.2.1.3.1.13	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.24	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVpIntervalShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.25	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
G32 atmVpIntervalShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.23	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
atmVpIntervalTable	1.3.6.1.4.1.164.12.2.1.2.1.3		not-accessible	The ATM Vp Interval table.
G32 atmVpIntervalTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.19	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVpIntervalTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVpIntervalTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.15	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVpIntervalTxAIS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.8	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.
G32 atmVpIntervalTxRDI	1.3.6.1.4.1.164.12.2.1.2.1.3.1.10	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.12	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
I32 atmVpIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.1.3.1.1	Integer32	read-only	The VPI of the VPL.
atmVpPerformance	1.3.6.1.4.1.164.12.2.1.2.1
INT atmVpPmAdminStatus	1.3.6.1.4.1.164.12.3.2.3.1.1.3	INTEGER	read-create	up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .
I32 atmVpPmBlockSize	1.3.6.1.4.1.164.12.3.2.3.1.1.5	Integer32	read-create	Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.
INT atmVpPMCurrentDir	1.3.6.1.4.1.164.12.2.1.2.1.2.1.2	INTEGER	read-only	The direction of performance management.
G32 atmVpPMCurrentECB	1.3.6.1.4.1.164.12.2.1.2.1.2.1.10	Gauge32	read-only	The counter associated with the number of ECB, encountered by the VPL of this ATM interface in the current 15 minute interval.
atmVpPMCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.1.2.1		not-accessible	An entry in the ATM VP Current table for Performance Management.
G32 atmVpPMCurrentErroredCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.7	Gauge32	read-only	The counter associated with the number of errored cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentES	1.3.6.1.4.1.164.12.2.1.2.1.2.1.12	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
INT atmVpPMCurrentIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.1.2.1.15	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVpPMCurrentLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.1.2.1.16	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
G32 atmVpPMCurrentLostCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.8	Gauge32	read-only	The counter associated with the number of lost cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.9	Gauge32	read-only	The counter associated with the number of misinserted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentRxClp0	1.3.6.1.4.1.164.12.2.1.2.1.2.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentRxClp01	1.3.6.1.4.1.164.12.2.1.2.1.2.1.5	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentSECB	1.3.6.1.4.1.164.12.2.1.2.1.2.1.11	Gauge32	read-only	The counter associated with the number of SECB, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentSES	1.3.6.1.4.1.164.12.2.1.2.1.2.1.13	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
atmVpPMCurrentTable	1.3.6.1.4.1.164.12.2.1.2.1.2		not-accessible	The ATM VP Current table for Performance Management.
G32 atmVpPMCurrentTxClp0	1.3.6.1.4.1.164.12.2.1.2.1.2.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentTxClp01	1.3.6.1.4.1.164.12.2.1.2.1.2.1.3	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.1.2.1.14	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
I32 atmVpPMCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.1.2.1.1	Integer32	read-only	The VPI of the VPL.
INT atmVpPmDirection	1.3.6.1.4.1.164.12.3.2.3.1.1.4	INTEGER	read-create	The direction of PM.
atmVpPmEntry	1.3.6.1.4.1.164.12.3.2.3.1.1		not-accessible	An entry in table.
I32 atmVpPmIfIndex	1.3.6.1.4.1.164.12.3.2.3.1.1.1	Integer32	read-only	The interface index of the ATM layer.
INT atmVpPMIntervalDir	1.3.6.1.4.1.164.12.2.1.2.1.4.1.2	INTEGER	read-only	The direction of performance management.
G32 atmVpPMIntervalECB	1.3.6.1.4.1.164.12.2.1.2.1.4.1.11	Gauge32	read-only	The counter associated with the number of ECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
atmVpPMIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.1.4.1		not-accessible	An entry in the ATM Vp Interval table for Performance Management.
G32 atmVpPMIntervalErroredCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.8	Gauge32	read-only	The counter associated with the number of Errored cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalES	1.3.6.1.4.1.164.12.2.1.2.1.4.1.13	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
INT atmVpPMIntervalLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.1.4.1.17	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
G32 atmVpPMIntervalLostCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.9	Gauge32	read-only	The counter associated with the number of Lost cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.10	Gauge32	read-only	The counter associated with the number of Misinserted cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
I32 atmVpPMIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.1.4.1.3	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
INT atmVpPMIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.1.4.1.16	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
G32 atmVpPMIntervalRxClp0	1.3.6.1.4.1.164.12.2.1.2.1.4.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalRxClp01	1.3.6.1.4.1.164.12.2.1.2.1.4.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalSECB	1.3.6.1.4.1.164.12.2.1.2.1.4.1.12	Gauge32	read-only	The counter associated with the number of SECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalSES	1.3.6.1.4.1.164.12.2.1.2.1.4.1.14	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
atmVpPMIntervalTable	1.3.6.1.4.1.164.12.2.1.2.1.4		not-accessible	The ATM Vp Interval table for Performance Management.
G32 atmVpPMIntervalTxClp0	1.3.6.1.4.1.164.12.2.1.2.1.4.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalTxClp01	1.3.6.1.4.1.164.12.2.1.2.1.4.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.1.4.1.15	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
I32 atmVpPMIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.1.4.1.1	Integer32	read-only	The VPI of the VPL.
G32 atmVpPMQoSCER	1.3.6.1.4.1.164.12.2.1.2.1.6.1.4	Gauge32	read-only	Cell Error Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVpPMQoSCLR	1.3.6.1.4.1.164.12.2.1.2.1.6.1.3	Gauge32	read-only	Cell Loss Ratio counter for the reference period (atmVpPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVpPMQoSCMR	1.3.6.1.4.1.164.12.2.1.2.1.6.1.5	Gauge32	read-only	Cell Misinsertion Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .
INT atmVpPMQoSDirection	1.3.6.1.4.1.164.12.2.1.2.1.6.1.1	INTEGER	read-only	The direction of performance management.
atmVpPMQoSEntry	1.3.6.1.4.1.164.12.2.1.2.1.6.1		not-accessible	.
INT atmVpPMQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.1.6.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
atmVpPMQoSTable	1.3.6.1.4.1.164.12.2.1.2.1.6		not-accessible	The PM VP QoS table.
ROW atmVpPmRowStatus	1.3.6.1.4.1.164.12.3.2.3.1.1.6	RowStatus	read-create	Creation/Deletion of rows in the table.
INT atmVpPmSink	1.3.6.1.4.1.164.12.3.2.3.1.1.7	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
INT atmVpPmSource	1.3.6.1.4.1.164.12.3.2.3.1.1.8	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
atmVpPmTable	1.3.6.1.4.1.164.12.3.2.3.1		not-accessible	This table contains parameters for VP performance monitoring.
I32 atmVpPmVpi	1.3.6.1.4.1.164.12.3.2.3.1.1.2	Integer32	read-only	The VPI of the Performance Monitoring VPL.
I32 atmVpQoSElapsedTime	1.3.6.1.4.1.164.12.2.1.2.1.5.1.2	Integer32	read-only	Elapsed Time in seconds. - for atmVpQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVpQoSPeriodRef = lastPeriod: The value of atmVpQoSElapsedTime when last systemResetAllStatsCmd was received.
atmVpQoSEntry	1.3.6.1.4.1.164.12.2.1.2.1.5.1		not-accessible	.
INT atmVpQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.1.5.1.1	INTEGER	read-only	This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
atmVpQoSTable	1.3.6.1.4.1.164.12.2.1.2.1.5		not-accessible	The VP QoS table.
G32 atmVpQoSUAS	1.3.6.1.4.1.164.12.2.1.2.1.5.1.3	Gauge32	read-only	Number of Unavailable Seconds for the reference period (atmVpQoSPeriodRef).
C32 atmVpShaperDiscarded	1.3.6.1.4.1.164.12.2.1.2.1.7.1.1	Counter32	read-only	The number of Cells that were discarded in the shaper on that VPC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.
C32 atmVpShaperEpdDropped	1.3.6.1.4.1.164.12.2.1.2.1.7.1.5	Counter32	read-only	The number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VP only.
INT atmVpShaperLevel	1.3.6.1.4.1.164.12.2.1.2.1.7.1.4	INTEGER	read-only	The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VPC.
I32 atmVpShaperMaxOccupation	1.3.6.1.4.1.164.12.2.1.2.1.7.1.3	Integer32	read-only	The Maximum number of Cells that were stored in the buffer, since this VP was activated. This parameter is limited to 20 bits.
I32 atmVpShaperOccupation	1.3.6.1.4.1.164.12.2.1.2.1.7.1.2	Integer32	read-only	The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.
atmVpShaperStatEntry	1.3.6.1.4.1.164.12.2.1.2.1.7.1		not-accessible	An entry in the ATM VP shaper statistics table.
atmVpShaperStatTable	1.3.6.1.4.1.164.12.2.1.2.1.7		not-accessible	The ATM VP shaper statistics table.
C32 atmVpShaperTotalEpdDropped	1.3.6.1.4.1.164.12.2.1.2.1.7.1.6	Counter32	read-only	The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VP only.
autoFileTransfer	1.3.6.1.4.1.164.6.2.12.13
autoFileTransferEntry	1.3.6.1.4.1.164.6.2.12.13.1.1		not-accessible	An entry in the table.
STR autoFileTransferFileName	1.3.6.1.4.1.164.6.2.12.13.1.1.3	SnmpAdminString	read-write	This object defines the name of the file to be uploaded.
I32 autoFileTransferOccurrenceRecurrence	1.3.6.1.4.1.164.6.2.12.13.1.1.6	Integer32	read-write	This object defines Occurrence reccurence interval, e.g N can be in 'every N alarms', 'every N log entries' etc. zero is used to indicate There's no Event Reccurence. (0= notApplicable) This object is taken into account only if autoFileTransferScheduling = recurrence Occurence Type (Alarms, etc.) is according to autoFileTransferType.
INT autoFileTransferScheduling	1.3.6.1.4.1.164.6.2.12.13.1.1.4	INTEGER	read-write	This object defines schedule for TFTP Automatic session(s) initiated by Agent, according to the value selected: now - initiate immediate single session. recurrence- initiate single session 'every M time units'. or 'every N occurrences' or upon both, (earliest event). Time reccurence period (M) is defined by fileTransferTimeRecurrence. Occurrence reccurence (N) is defined by fileTransferOccurrenceRecurrence. Zero value means that the object is not relevant (not taken into account for the recurrence). It is invalid that both will have zero values in our case (recurrence). When both are non zero, file is transferred upon earliest event
IP autoFileTransferServerIp	1.3.6.1.4.1.164.6.2.12.13.1.1.2	IpAddress	read-write	This object defines the IP Address of the server to which the file is uploaded.
autoFileTransferTable	1.3.6.1.4.1.164.6.2.12.13.1		not-accessible	Scheduling configuration table for Agent initiated file transfer.
I32 autoFileTransferTimeRecurrence	1.3.6.1.4.1.164.6.2.12.13.1.1.5	Integer32	read-write	This object defines time reccurence interval, e.g. M can be 'every M days', 'every M hours' etc. Zero is used to indicate there's no time reccurence (0= notApplicable). This object is taken into account only if autoFileTransferScheduling = recurrence For LA-110 time units are days.
INT autoFileTransferType	1.3.6.1.4.1.164.6.2.12.13.1.1.1	INTEGER	read-only	This object defines the type of file to be transferred by agent.
bdbandConfig	1.3.6.1.4.1.164.3.1.6.8.1
bitMappingEntry	1.3.6.1.4.1.164.6.2.38.1		not-accessible	Each entry in the table describes a correlation of a bit location to an interface. For ACE-2002 - Upon creation of a new LAN VCC the agent will add an entry to this table that will define the bit location for that VCC.
I32 bitMappingIndex	1.3.6.1.4.1.164.6.2.38.1.2	Integer32	read-only	The interface index or any other index that should be mapped.
I32 bitMappingLocation	1.3.6.1.4.1.164.6.2.38.1.1	Integer32	not-accessible	The bit location in an octet string.
bitMappingTable	1.3.6.1.4.1.164.6.2.38		not-accessible	This table maps bits of an octet string to an interface. For ACE-2002 this table is used to map bits of VLAN port lists to LAN VCC's. This table is the opposite view of the xcTable for xcBitMapping. It is used to ease the bit translation for the NMS.
OCT bitMappingView	1.3.6.1.4.1.164.6.2.39	OCTET STRING	read-only	A view of the bitMappingTable in one object - each entry in the biMappingTable will have the corresponding Bit of this object (bitMappingLocation) = '1'. For ACE-2002 it is used to describe all the existing LAN VCC's So that the NMS can easily calculate which VCC's can be selected as members for a VLAN, instead of reading all the bitMapping Table.
broadbandIf	1.3.6.1.4.1.164.3.1.6.8
NTF bundleConnectionStatusTrap	1.3.6.1.4.1.164.6.1.3.0.15			This trap is sent upon any change in the connectivity status of a Bundle (ip2IfOperStatus). The ifAlias index is the ifIndex of the bundle that its status has been changed.
NTF channelOperStatusTrap	1.3.6.1.4.1.164.6.1.3.0.9			This trap is sent upon any change in one or more channels.
I32 chassTotalNoOfClSlt	1.3.6.1.4.1.164.3.3.1.2.1.4	Integer32	read-only	This object indicates the number of physical Common Logic slots in the chassis.
I32 chassTotalNoOfIoSlt	1.3.6.1.4.1.164.3.3.1.2.1.2	Integer32	read-only	This object indicates the total number of physical IO slots in the chassis, (not all slots must be occupied and active).
I32 chassTotalNoOfMlSlt	1.3.6.1.4.1.164.3.3.1.2.1.5	Integer32	read-only	This object indicates the number of physical Main Link slots in the chassis (Kmux).
I32 chassTotalNoOfPsSlt	1.3.6.1.4.1.164.3.3.1.2.1.3	Integer32	read-only	This object indicates the number of physical Power Supply slots in the chassis.
I32 chassTotalNoOfSlt	1.3.6.1.4.1.164.3.3.1.2.1.1	Integer32	read-only	This object indicates the number of physical slots in the Hub chassis.
I32 chasTotalNoOfClSlt	1.3.6.1.4.1.164.3.1.1.5	Integer32	read-only	This entry indicates the number of physical Common Logic slots in the chassis.
I32 chasTotalNoOfIoSlt	1.3.6.1.4.1.164.3.1.1.3	Integer32	read-only	This entry indicates the total number of physical IO slots in the chassis, (not all slots hardware should be occupied and active) .
I32 chasTotalNoOfPsSlt	1.3.6.1.4.1.164.3.1.1.4	Integer32	read-only	This entry indicates the number of physical Power Supply slots in the chassis.
I32 chasTotalNoOfSlt	1.3.6.1.4.1.164.3.1.1.2	Integer32	read-only	This entry indicates the number of physical slots in the chassis.
STR chasVersion	1.3.6.1.4.1.164.3.1.1.1	DisplayString	read-only	An ASCII string for description and display of the agent chassis version.
chasWanGen	1.3.6.1.4.1.164.3.1.1
I32 clearDwldStatusLog	1.3.6.1.4.1.164.6.2.12.12	Integer32	read-write	This object clears the status log. Value: off(2), external(3), internal(4) The Agent will change the value of this MIB object to off(2) automatically, after accepting the command .
NTF clkSrcChangeTrap	1.3.6.1.4.1.164.6.1.0.10			This trap is sent upon any change in Clock Source.
cmprAgnGen	1.3.6.1.4.1.164.3.1.2.3
I32 cmprCnfgIdx	1.3.6.1.4.1.164.3.3.4.1.1.2	Integer32	read-only	This object indicates the configuration number the Compressed information relates to.
cmprEntry	1.3.6.1.4.1.164.3.3.4.1.1		not-accessible	An entry in table.
cmprMdlGen	1.3.6.1.4.1.164.3.1.3.3
OCT cmprObj	1.3.6.1.4.1.164.3.3.4.1.1.6	OCTET STRING	read-write	This object is the compressed information itself, according to a predefined format, both agent and NMS agreed about.
cmprPrtGen	1.3.6.1.4.1.164.3.1.4.3
I32 cmprPrtIdx	1.3.6.1.4.1.164.3.3.4.1.1.5	Integer32	read-only	This object indicates a unique identifier of the port, the compressed information relates to. For DXC - according to the order in the card of cmprSltIdx: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For FCD: see product's specification. If the port number is irrelevant to this parameter (if it is a system/card level alarm) the value will be 9999.
INT cmprSltIdx	1.3.6.1.4.1.164.3.3.4.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. When the unit is stand-alone or this object is not applicable, 255 will be used.
cmprTable	1.3.6.1.4.1.164.3.3.4.1		not-accessible	A table.
I32 cmprTypeIdx	1.3.6.1.4.1.164.3.3.4.1.1.1	Integer32	read-only	This object indicates the Type of the Compressed data referred (which table, which level, etc). The type is a code according to a convention between agent and NMS.
I32 cmprVersion	1.3.6.1.4.1.164.3.3.4.1.1.3	Integer32	read-only	This object indicates the version of the internal format of the Compressed data (the version of the convention used).
cnfgAgnGen	1.3.6.1.4.1.164.3.1.2.2
NTF cnfgFlipTrap	1.3.6.1.4.1.164.3.2.0.3			This trap is sent upon change of the active Configuration DB. Attached, is the new active Configuration no.
cnfgMdlGen	1.3.6.1.4.1.164.3.1.3.2
cnfgMdlMux	1.3.6.1.4.1.164.3.2.2.1
cnfgPrtGen	1.3.6.1.4.1.164.3.1.4.2
cnfgPrtMux	1.3.6.1.4.1.164.3.2.3.2
NTF cnfgUpdateTrap	1.3.6.1.4.1.164.3.3.0.6			This trap is sent upon change of the active Configuration DB.
OCT cosProfileCosMapping	1.3.6.1.4.1.164.6.3.10.1.5	OCTET STRING	read-create	This attribute defines the value of the CoS that is assigned for each priority. The number of the valid octets depends upon the priority method selected: Octet 0 corresponds to priority = 0 Octet 1 corresponds to priority = 1 ... Octet 63 corresponds to priority = 63.
INT cosProfileCosMethod	1.3.6.1.4.1.164.6.3.10.1.3	INTEGER	read-create	Defines the priority method upon CoS mapping is done.
cosProfileEntry	1.3.6.1.4.1.164.6.3.10.1		not-accessible	A conceptual row where each row contains one CoS attributes.
U32 cosProfileIndex	1.3.6.1.4.1.164.6.3.10.1.1	Unsigned32	not-accessible	Defines the CoS Profile ID.
STR cosProfileName	1.3.6.1.4.1.164.6.3.10.1.4	SnmpAdminString	read-create	This attribute defines the name assigned to CoS profile.
ROW cosProfileRowStatus	1.3.6.1.4.1.164.6.3.10.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
cosProfileTable	1.3.6.1.4.1.164.6.3.10		not-accessible	Class of Service Profile table. Each profile holds a priority method, and a mappring function that maps the priority values (range according to the method) into CoS values.
dacsMux	1.3.6.1.4.1.164.3.3
NTF dacsMuxAlarmsTrap	1.3.6.1.4.1.164.3.3.0.2			This trap is sent when an alarm occurs.
dacsMuxEvents	1.3.6.1.4.1.164.3.3.0			The events for DACS MUX.
INT dhcpClientAction	1.3.6.1.4.1.164.11.7.2.2.1.6.1.1	INTEGER	read-write	This parameter default value is enable(3). Setting this attribute to disable (2), will disable DHCP Client action for this interface. This parameter can be changed to disable (2) only (it cannot be changed from disable to enable).
dhcpClientEntry	1.3.6.1.4.1.164.11.7.2.2.1.6.1		not-accessible	DHCP Client parameters per entry of the DHCP Client table.
I32 dhcpClientLeaseExpirationTime	1.3.6.1.4.1.164.11.7.2.2.1.6.1.3	Integer32	read-only	This parameter holds the time (in minutes) left until lease expiration.
IP dhcpClientServerIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.6.1.2	IpAddress	read-write	DHCP Server IP Address.
STR dhcpClientStatus	1.3.6.1.4.1.164.11.7.2.2.1.6.1.4	DisplayString	read-only	This parametr displays the DHCP status.
dhcpClientTable	1.3.6.1.4.1.164.11.7.2.2.1.6		not-accessible	A list of DHCP client entries.
dhcpIfClientEntry	1.3.6.1.4.1.164.11.7.2.2.1.7.1		not-accessible	DHCP Clients per entry of the DHCP Interface Client table.
IP dhcpIfClientIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.7.1.2	IpAddress	read-create	DHCP Client IP Address.
ROW dhcpIfClientRowStatus	1.3.6.1.4.1.164.11.7.2.2.1.7.1.3	RowStatus	read-create	The row status used for creating, modifying, and deleting instances of the columnar objects in the dhcpIfClientTable. For Vmux Devices, it will be possible only to Delete instances. The addition of Clients will be done automatically by the Server according to Network messages that are sent by the Clients; not via SNMP. In order to Delete a Client, this MIB object should be set to: destroy (6).
dhcpIfClientTable	1.3.6.1.4.1.164.11.7.2.2.1.7		not-accessible	DHCP client entries for each Interface.
dhcpPoolAllocEntry	1.3.6.1.4.1.164.11.7.2.2.1.3.1		not-accessible	DHCP Pool Allocation parameters per entry of the DHCP Pool Allocation table.
INT dhcpPoolAllocFlags	1.3.6.1.4.1.164.11.7.2.2.1.3.1.5	INTEGER	read-only	These flags indicates status of each IP address. User may change value to free, via dhcpPoolAllocFreeCmd
INT dhcpPoolAllocFreeCmd	1.3.6.1.4.1.164.11.7.2.2.1.3.1.6	INTEGER	read-write	Setting this attribute to On (3), will enforce the agent to Free this entry. The Agent will change the value of this MIB object to off(2) automatically, after performing the command. Setting this object to off(2), will do nothing
IP dhcpPoolAllocLeasingIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.2	IpAddress	read-only	Single IP Address belonging to dhcp pool whose Lowest Ip Address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing or may be leased by Host its MacAddress is dhcpPoolAllocMacAddress. All posible statuses of IP address are indicated by dhcpPoolAllocFlags
IP dhcpPoolAllocLowIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.1	IpAddress	read-only	Lowest IP address of this pool, value eqaul to wrDhcpLowIpAddress for the pool.
MAC dhcpPoolAllocMacAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.3	MacAddress	read-only	MAC Address to which the IP address has been leased
dhcpPoolAllocTable	1.3.6.1.4.1.164.11.7.2.2.1.3		not-accessible	A list of DHCP Pool Allocation entries. Each entry (row) consist of a single IP Address belonging to DHCP pool whose lowest IP address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing, or may already be leased (in use) by Host it's MacAddress is dhcpPoolAllocMacAddress. Time left for leasing period is indicated by dhcpPoolAllocTimeLeft. All posible statuses of IP address are indicated and controlled by dhcpPoolAllocFlags
I32 dhcpPoolAllocTimeLeft	1.3.6.1.4.1.164.11.7.2.2.1.3.1.4	Integer32	read-only	IP address leasing time left in seconds
INT dhcpRelayAction	1.3.6.1.4.1.164.11.7.2.2.1.4.1.1	INTEGER	read-write	Setting this attribute to enable (3), will enable DHCP Relay action for this interface (Only if DHCP Server is disabled for device - wrDhcpAction=disable). dhcpRelayServerIpAddressaddress should not be 0.0.0.0 when enable is set
dhcpRelayEntry	1.3.6.1.4.1.164.11.7.2.2.1.4.1		not-accessible	DHCP Relay parameters per entry of the DHCP relay table.
I32 dhcpRelayMaxHop	1.3.6.1.4.1.164.11.7.2.2.1.4.1.3	Integer32	read-write	Maximum number of hops till DHCP Server. upper limit is 16 hops
IP dhcpRelayServerIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.4.1.2	IpAddress	read-write	DHCP Server IP Address.
dhcpRelayTable	1.3.6.1.4.1.164.11.7.2.2.1.4		not-accessible	A list of DHCP relay entries.
INT dhcpServerAction	1.3.6.1.4.1.164.11.7.2.2.1.8	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the Server. deleteAllClients (3) is an option that is used for a device functioning as a server. It will remove all the clients from all the interfaces of the device. When the operation is complete, the agent will return a noOp (2) value.
diverseIfWanGen	1.3.6.1.4.1.164.3.1.6
dot1agXCfmMdEntry	1.3.6.1.4.1.164.3.1.6.1.3.8.1		not-accessible	The Maintenance Domain table entry.
INT dot1agXCfmMdProtocol	1.3.6.1.4.1.164.3.1.6.1.3.8.1.1	INTEGER	read-create	.
dot1agXCfmMdTable	1.3.6.1.4.1.164.3.1.6.1.3.8		not-accessible	The Maintenance Domain table. Each row in the table represents a different maintenance association.
INT dot1agXCfmMepCcStat	1.3.6.1.4.1.164.3.1.6.1.3.10.1.1	INTEGER	read-only	This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpectedMep -A MEP detects an Unexpected MEP condition when a CCM frame arrives with the correct MEG level, the correct MEG ID, but an unexpected MEP ID, which includes the MEP's own MEP ID. unexpectedMeLevel - A MEP detects an Unexpected MEG Level condition when a CCM frame arrives with incorrect MEG Level. Incorrect MEG Level is less than the MEP's own MEG level. unexpectedPeriod - A MEP detects an Unexpected Period condition when a CCM frame arrives with a correct MEG level. a correct MEG ID, a correct MEP ID, but with the Period field value different from the MEP's own CCM transmission period. rdi - A MEP detects RDI when it receives a CCM frame with the RDI field set.
INT dot1agXCfmMepContinuityVerMode	1.3.6.1.4.1.164.3.1.6.1.3.9.1.1	INTEGER	read-create	This object determines the OAM behavior of the MEP: disabled - no Continuity Verification is done cc_based - Continuity Verification is done based on incoming CC messages lb_based - Continuity Verification is done based on loopback messages.
dot1agXCfmMepDbEntry	1.3.6.1.4.1.164.3.1.6.1.3.10.1		not-accessible	The MEP Database table entry.
dot1agXCfmMepDbTable	1.3.6.1.4.1.164.3.1.6.1.3.10		not-accessible	The MEP DB table
INT dot1agXCfmMepDestAddrType	1.3.6.1.4.1.164.3.1.6.1.3.9.1.2	INTEGER	read-create	This object determines if the OAM messages are sent to user defined unicast address, or to RAD proprietary multicast address.
MAC dot1agXCfmMepDestMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.9.1.3	MacAddress	read-create	This object determines the MAC address that OAM packets are sent to.
dot1agXCfmMepEntry	1.3.6.1.4.1.164.3.1.6.1.3.9.1		not-accessible	The MEP table entry
dot1agXCfmMepTable	1.3.6.1.4.1.164.3.1.6.1.3.9		not-accessible	The Maintenance Association End Point (MEP) table.
dot3OamDescrEntry	1.3.6.1.4.1.164.3.1.6.1.6.1.1		not-accessible	Each entry corresponds to a single OAM EFM Descriptor (profile). Each Descriptor contains a set of OAM EFM Link configuration parameters. The configuration parameters are applied to the OAM EFM Links referencing this Descriptor (see dot3OamXDescrId object). Descriptors may be created/deleted using the row creation/deletion mechanism via dot3OamDescrRowStatus. If an active entry is referenced in dot3OamXDescrId, the entry MUST remain active until all references are removed.
U32 dot3OamDescrId	1.3.6.1.4.1.164.3.1.6.1.6.1.1.1	Unsigned32	not-accessible	This object is the unique index associated with this Descriptor (profile). Entries in this table are referenced via the object dot3OamXDescrId in dot3OamXEntry.
INT dot3OamDescrLbRxOperation	1.3.6.1.4.1.164.3.1.6.1.6.1.1.4	INTEGER	read-create	Since OAM loopback is a disruptive operation (user traffic does not pass), this object provides a mechanism to provide control: whether received OAM loopback commands are processed or ignored, for the OAM Link referencing this Descriptor. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), received loopback commands are processed. The default value is to ignore loopback commands (ignore(1)).
INT dot3OamDescrMode	1.3.6.1.4.1.164.3.1.6.1.6.1.1.3	INTEGER	read-create	This object controls the mode of OAM operation for an Ethernet-like interface referencing this Descriptor. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional capabilities to initiate monitoring activities with the remote OAM peer entity, while passive mode generally waits for the peer to initiate OAM actions with it. As an example, an active OAM entity can put the remote OAM entity in a loopback state, where a passive OAM entity cannot.
U32 dot3OamDescrRateLimit	1.3.6.1.4.1.164.3.1.6.1.6.1.1.5	Unsigned32	read-create	This object defines how many OAM frames can be sent per second (maximum) for an OAM EFM Link referencing this Descriptor.
ROW dot3OamDescrRowStatus	1.3.6.1.4.1.164.3.1.6.1.6.1.1.2	RowStatus	read-create	This object controls creation/deletion of the associated entry in this table per the semantics of RowStatus. If an active entry is referenced in dot3OamXDescrId, the entry MUST remain active until all references are removed.
dot3OamDescrTable	1.3.6.1.4.1.164.3.1.6.1.6.1		not-accessible	This table supports definitions of Descriptors (profiles) of OAM EFM Links.
dot3OamEvents	1.3.6.1.4.1.164.3.1.6.1.6.0
NTF dot3OamOperStatusChange	1.3.6.1.4.1.164.3.1.6.1.6.0.1			This trap is sent when OAM EFM Link goes Up or Down. Up - is considered when dot3OamOperStatus value changes to operational(9) from any other value. Down - is considered when dot3OamOperStatus value changes from operational(9) to any other value.
NTF dot3OamPeerEvent	1.3.6.1.4.1.164.3.1.6.1.6.0.2			This trap is sent when value of dot3OamXPeerState changes from any value to one of the following values: linkFault, dyingGasp, criticalEvent. This trap has no recovery (clearing value).
U32 dot3OamXDescrId	1.3.6.1.4.1.164.3.1.6.1.6.2.1.1	Unsigned32	read-write	This object points to an entry of dot3OamDescrTable (dot3OamDescrId), which defines part of the configuration parameters for this OAM EFM Link. As long as one of the OAM EFM Links refers an entry in the dot3OamDescrTable, this entry cannot be removed. When an OAM EFM Link supports this object (RW), the standard MIB objects of: dot3OamMode (parallel to dot3OamDescrMode) and dot3OamLoopbackIgnoreRx (parallel to dot3OamDescrLbRxOperation) will be supported by Agent RO.
dot3OamXEntry	1.3.6.1.4.1.164.3.1.6.1.6.2.1		not-accessible	An entry in dot3OamXTable.
INT dot3OamXPeerState	1.3.6.1.4.1.164.3.1.6.1.6.2.1.2	INTEGER	read-only	This object reports the state of the Peer of the OAM EFM Link. unknown - at the initialization of the device, or after Reset, when there is still no data about the peer's state. operational - usually after unknown state, when device senses that peer is OK. linkFault - Loss of Signal is detected by the receiver. dyingGasp - Unrecoverable condition has occurred (e.g power failure) criticalEvent - Unspecified Critical Event has occured.
dot3OamXTable	1.3.6.1.4.1.164.3.1.6.1.6.2		not-accessible	This table is an extension of dot3OamTable of standard DOT3-OAM-MIB.
NTF ds1AisSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.10			This trap indicates near end (Local) Loss of Frame Alignment (Sync Loss), caused by the reception of AIS at the user DS1 interface.
NTF ds1AisTrap	1.3.6.1.4.1.164.3.1.6.4.0.11			This trap indicates AIS being received at the user DS1 interface.
NTF ds1BpvErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.4			This trap indicates a Bipolar Violation (BPV) error has been detected at the user DS1 interface.
NTF ds1Crc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.6			This trap indicates that a frame with CRC-4 error has been detected at the user DS1 interface.
NTF ds1ExcessiveBpvTrap	1.3.6.1.4.1.164.3.1.6.4.0.5			This trap indicates excessive number of Bipolar Violation errors (BPV) detected by the user DS1 interface
NTF ds1ExcessiveCrc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.16			This trap indicates that the error rate detected on the CRC-4 bits at the user DS1 interface, is high.
NTF ds1ExcessiveErrorRatioTrap	1.3.6.1.4.1.164.3.1.6.4.0.7			This trap indicates that the error rate, detected at the user DS1 interface, on the frame synchronization bits is high, as defined by ITU-T Rec. G.732.
NTF ds1ExcessiveFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.15			This trap indicates that the number of Frame Slips detected at the user DS1 interface, during the last minute exceeds threshold. For LA-110, threshold value is 10. This usually indicates timing problems (incorrect selection of timing reference) on the user DS1.
NTF ds1ExcessiveLocalMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.17			This trap indicates that the number of local Loss of Multiframe Alignment events, detected at the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveLocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.20			This trap indicates that the number of Loss of local Synchronization alarms reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.18			This trap indicates that the number of Loss of multiframe alignment events reported by the remote unit connected to the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.19			This trap indicates that the number of far end (remote) Loss of Synchronization alarms, reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
ds1Interface	1.3.6.1.4.1.164.3.1.6.4
NTF ds1LinkFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.3			This trap indicates that a Frame Slip occurred at the user DS1 interface. This usually indicates timing problems (incorrect selection of timing reference), on the user DS1 link.
NTF ds1LocalLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.14			This trap indicates that a local loopback has been activated on the user port.
NTF ds1LocalMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.1			This trap indicates near end (Local) Loss of Multiframe Alignment, of the user E1 interface.
NTF ds1LocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.9			This trap indicates near end (Local) Loss of Frame Alignment failure (Sync Loss), of the user DS1 interface
NTF ds1NetworkRemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.12			This trap indicates that a remote loopback has been activated, on the local uplink interface.
NTF ds1RemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.13			This trap indicates that a remote loopback has been activated, on the local user port.
NTF ds1RemoteMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.2			This trap indicates that the far end (remote) unit, connected to the user E1 interface, reports Loss of Multiframe Alignment.
NTF ds1RemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.8			This trap indicates that the far-end (remote) unit, connected to user DS1 interface, reports Loss of Frame Alignment (Sync Loss).
NTF ds1SignalLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.21			This trap indicates Signal Loss. (possible reason - cable disconnection. etc.)
ds3Interface	1.3.6.1.4.1.164.3.1.6.3
dscpMapping	1.3.6.1.4.1.164.6.3.2
I32 dscpMappingCnfgIdx	1.3.6.1.4.1.164.6.3.2.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer to. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.
DSC dscpMappingDscpIdx	1.3.6.1.4.1.164.6.3.2.1.1.2	Dscp	not-accessible	DSCP value of the incoming IP packet
dscpMappingEntry	1.3.6.1.4.1.164.6.3.2.1.1		not-accessible	An entry in dscpMappingTable.
I32 dscpMappingRegenPriority	1.3.6.1.4.1.164.6.3.2.1.1.3	Integer32	read-write	The Regenerated Priority level the incoming DSCP value is mapped to. For FCD-155, valid values are 0,1,2,3
dscpMappingTable	1.3.6.1.4.1.164.6.3.2.1		not-accessible	Mapping of DSCP value to a regenerated priority level.
INT dsx1AisEnable	1.3.6.1.4.1.164.3.1.6.4.2.1.12	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).
I32 dsx1BundleNextIndex	1.3.6.1.4.1.164.3.1.6.4.2.1.21	Integer32	read-only	This parameter indicates the Next free Bundle Index for this DS1 port.
I32 dsx1ClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.19	Integer32	read-write	This entry specifies the source from which the clock will be taken. Refer to device specification for source Index
INT dsx1CRC6CalcMode	1.3.6.1.4.1.164.3.1.6.4.2.1.22	INTEGER	read-write	This object determines the CRC6 Calculation mode. jtG704 =JT-G704 = the Japanese standard ituG704=ITU-G704 = the International standard This parameter is applicable for J1 only.
INT dsx1CsuLoop	1.3.6.1.4.1.164.3.1.6.4.2.1.18	INTEGER	read-write	This parameter defines where the CSU loop will be done: local - locally (by IPmux) towards the TDM device transparent - transferred to Remote Device that will send it to its connected TDM device. remote - Remote Device will close the loop towards the Local Device.
PER dsx1CurrentAIS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.4	PerfCurrentCount	read-only	The counter associated with the number of AIS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentBPV	1.3.6.1.4.1.164.3.1.6.4.1.2.1.9	PerfCurrentCount	read-only	The counter associated with the number of BPVs (Bi-Polar Violations) encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentCRCErrors	1.3.6.1.4.1.164.3.1.6.4.1.2.1.12	PerfCurrentCount	read-only	Counts the number of CRC error events, encountered in the current 15 minute interval.
PER dsx1CurrentFEBE	1.3.6.1.4.1.164.3.1.6.4.1.2.1.7	PerfCurrentCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in the current 15 minute interval.
PER dsx1CurrentLOC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.3	PerfCurrentCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
PER dsx1CurrentLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.10	PerfCurrentCount	read-only	Loss of CRC4 Multi-Frame sequence in E1. encountered in the current 15 minute interval
PER dsx1CurrentLOF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.2	PerfCurrentCount	read-only	The counter associated with the number of LOF seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOFC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.11	PerfCurrentCount	read-only	Counts the number of loss of frame events measured. encountered in the current 15 minute interval
PER dsx1CurrentLOMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.6	PerfCurrentCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
PER dsx1CurrentLOS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.1	PerfCurrentCount	read-only	The counter associated with the number of LOS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentRAI	1.3.6.1.4.1.164.3.1.6.4.1.2.1.5	PerfCurrentCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
OCT dsx1CurrentStatus	1.3.6.1.4.1.164.3.1.6.4.1.2.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
dsx1DataStreamStatEntry	1.3.6.1.4.1.164.3.1.6.4.1.5.1		not-accessible	An entry in the DS1 Data Stream Statistics table.
I32 dsx1DataStreamStatIfIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.1	Integer32	not-accessible	The index of the DS1 interface. It may be ifIndex.
C32 dsx1DataStreamStatInBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.5	Counter32	read-only	The counter associated with the number of received bytes, encountered by the DS1 Data Stream.
I32 dsx1DataStreamStatIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.2	Integer32	not-accessible	The DS1 Data Stream Index. For Vmux - the following indices are used: 1 for Transparent 2-3 for SS71-SS72 (respectively) 4-7 for Data1-Data4 (respectively) 8 for HDLC Ph2 Compatible 9-16 for Sub-CH1-1...Sub-CH1-8 (respectively).
C32 dsx1DataStreamStatInDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.6	Counter32	read-only	The counter associated with the number of Discarded incoming frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.7	Counter32	read-only	The counter associated with the number of received Errored frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.4	Counter32	read-only	The counter associated with the number of received frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.9	Counter32	read-only	The counter associated with the number of transmitted bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.10	Counter32	read-only	The counter associated with the number of Discarded outgoing frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.11	Counter32	read-only	The counter associated with the number of errored transmitted frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.8	Counter32	read-only	The counter associated with the number of transmitted frames, encountered by the DS1 Data Stream.
dsx1DataStreamStatTable	1.3.6.1.4.1.164.3.1.6.4.1.5		not-accessible	The DS1 Data Stream Statistics table.
T/F dsx1DataStreamStatValid	1.3.6.1.4.1.164.3.1.6.4.1.5.1.3	TruthValue	read-only	Indicates whether this Data Stream is valid or not. When invalid - all counters are irrelevant.
INT dsx1dBTxGain	1.3.6.1.4.1.164.3.1.6.4.2.1.3	INTEGER	read-write	Transmit line Gain for T1 CSU line mode.
INT dsx1EchoCancelerModule	1.3.6.1.4.1.164.3.1.6.4.2.1.14	INTEGER	read-only	This parameter indicates whether echo-cancellation module exists for this line.
I32 dsx1IdleCode	1.3.6.1.4.1.164.3.1.6.4.2.1.1	Integer32	read-write	Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).
NUM dsx1IntervalAIS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.4	PerfIntervalCount	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalBPV	1.3.6.1.4.1.164.3.1.6.4.1.3.1.9	PerfIntervalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalFEBE	1.3.6.1.4.1.164.3.1.6.4.1.3.1.7	PerfIntervalCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in one of the previous 96, individual, 15 minute intervals.
NUM dsx1IntervalLOC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.3	PerfIntervalCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
NUM dsx1IntervalLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.10	PerfIntervalCount	read-only	Loss of CRC4 Multi-Frame sequence in E1.
NUM dsx1IntervalLOF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.2	PerfIntervalCount	read-only	The counter associated with the number of OOF seconds, encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.11	PerfIntervalCount	read-only	Counts the number of loss of frame events measured in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.6	PerfIntervalCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
NUM dsx1IntervalLOS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.1	PerfIntervalCount	read-only	The counter associated with the number of LOS seconds , encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalRAI	1.3.6.1.4.1.164.3.1.6.4.1.3.1.5	PerfIntervalCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
OCT dsx1IntervalStatus	1.3.6.1.4.1.164.3.1.6.4.1.3.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
INT dsx1LeasedLine	1.3.6.1.4.1.164.3.1.6.4.2.1.17	INTEGER	read-write	This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).
INT dsx1LineAdaptiveTimingMode	1.3.6.1.4.1.164.3.1.6.4.2.1.10	INTEGER	read-write	Enables end to end clock synchronization. Default value - off.
INT dsx1LineMode	1.3.6.1.4.1.164.3.1.6.4.2.1.2	INTEGER	read-write	T1 device operation mode. Valid for T1 only.
INT dsx1OosSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.20	INTEGER	read-write	This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. 'Mark' = both A and B signaling bits are forced to '1' during out-of-service periods. 'spaceMark' = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. 'markSpace' = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. - '0'= 0 for T1, 1 for E1, or user defined value for Space - '1'= 1 for T1, 0 for E1, or user defined value for Mark.
INT dsx1PortFunction	1.3.6.1.4.1.164.3.1.6.4.2.1.15	INTEGER	read-write	This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as an IMA-ATM. cesPsn - The port will function as a CES-PSN. abis - The port will function as an Abis.
INT dsx1PortMultiplier	1.3.6.1.4.1.164.3.1.6.4.2.1.16	INTEGER	read-write	This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.
INT dsx1RestoreTime	1.3.6.1.4.1.164.3.1.6.4.2.1.5	INTEGER	read-write	Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = CCITT
INT dsx1RxSensitivity	1.3.6.1.4.1.164.3.1.6.4.2.1.4	INTEGER	read-write	Low Sensitivity is considered Short Haul while High Sensitivity is considered Long Haul. The actual values depend on the LIU. Examples: - E1: -12dB is considered Short Haul ; -43dB is considered Long Haul - T1: -12dB is considered Short Haul ; -36dB is considered Long Haul.
INT dsx1Scramble	1.3.6.1.4.1.164.3.1.6.4.2.1.9	INTEGER	read-write	Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicable for E1. active - will scramble/descramble the payload ATM cell notActive - will not scramble/descramble.
INT dsx1SendUponFail	1.3.6.1.4.1.164.3.1.6.4.2.1.23	INTEGER	read-write	This object determines which notification will be sent to the other side upon fail of another interface. In Ipmux14 the notification is sent upon failure of the Ethernet link.
I32 dsx1TcFirstSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.6	Integer32	read-write	Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used also for Space Signaling Code (in this case 0xFF is not NULL).
I32 dsx1TcPattern	1.3.6.1.4.1.164.3.1.6.4.2.1.8	Integer32	read-write	Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.
I32 dsx1TcSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.7	Integer32	read-write	Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).
PER dsx1TotalBPV	1.3.6.1.4.1.164.3.1.6.4.1.4.1.9	PerfTotalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.4.1.11	PerfTotalCount	read-only	The counter associated with the number loss of frames encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOS	1.3.6.1.4.1.164.3.1.6.4.1.4.1.1	PerfTotalCount	read-only	The counter associated with the number of LOS (Loss of Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
OCT dsx1TsEchoCancel	1.3.6.1.4.1.164.3.1.6.4.2.1.13	OCTET STRING	read-write	This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., 4th octet bit'7' = TS#32. Octets and bits order is from left to right: [31,30,..24] [23..16] [15..8] [7..0] MSB LSB MSB LSB MSB LSB MSB LSB For each bit values are: 0 - Echo-Cancellation off. 1 - Echo-Cancellation on.
INT dsx1TxClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.11	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered receive clock from another interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'system' indicates that the system clock is used as the transmit clock.
dsx1XConfigEntry	1.3.6.1.4.1.164.3.1.6.4.2.1		not-accessible	An entry containing additional configuration parameters.
dsx1XConfigTable	1.3.6.1.4.1.164.3.1.6.4.2		not-accessible	An extension to the DS1 Configuration table.
dsx1XCurrentEntry	1.3.6.1.4.1.164.3.1.6.4.1.2.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
dsx1XCurrentTable	1.3.6.1.4.1.164.3.1.6.4.1.2		not-accessible	A list of current statistics entries. This table contains additional objects for the current table.
dsx1XIntervalEntry	1.3.6.1.4.1.164.3.1.6.4.1.3.1		not-accessible	An entry containing additional statistical counters applicable to a particular interval table.
dsx1XIntervalTable	1.3.6.1.4.1.164.3.1.6.4.1.3		not-accessible	A list of Interval entries. This table contains additional objects for the interval table.
dsx1XTotalEntry	1.3.6.1.4.1.164.3.1.6.4.1.4.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
dsx1XTotalTable	1.3.6.1.4.1.164.3.1.6.4.1.4		not-accessible	A list of Total statistics entries. This table contains additional objects for the Total table.
INT dsx3AisEnable	1.3.6.1.4.1.164.3.1.6.3.2.1.1	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet (for TDMoIP) line is disconnected.
NUM dsx3MappingDs3Index	1.3.6.1.4.1.164.3.1.6.3.3.1.1	InterfaceIndex	not-accessible	The index value which uniquely identifies the DS3/E3 interface to which this entry is applicable. This value is also equal to dsx3LineIndex used in dsx3ConfigEntry. For RICi-16 this is the ifIndex of the T3 interface.
dsx3MappingEntry	1.3.6.1.4.1.164.3.1.6.3.3.1		not-accessible	An entry in the DS3 mapping table.
NUM dsx3MappingIfIndex	1.3.6.1.4.1.164.3.1.6.3.3.1.3	InterfaceIndex	read-write	An index value that uniquely identifies a logical or physical interface mapped to a DS3/E3 channel. If no interface is currently using a channel, the value should be zero. If a single interface occupies more than one channel, that ifIndex value will be found in multiple channels. For RICi-16 this is the ifIndex of the T1 or VCG interface.
U32 dsx3MappingNumber	1.3.6.1.4.1.164.3.1.6.3.3.1.2	Unsigned32	not-accessible	The channel number for this entry. For RICi-16 this is the channel number 1...28.
dsx3MappingTable	1.3.6.1.4.1.164.3.1.6.3.3		not-accessible	The DS3/E3 mapping table associates DS3/E3 channels with logical or physical interfaces. For example, consider a DS3 device with 16 T1's and 1 VCG. There are 28 logical/internal channels, numbered 1 through 28 but only 17 are actually connected. We might describe the allocation of channels, in the dsx3MappingTable, as follows: dsx3MappingIfIndex.1. 1 = 1001 dsx3MappingIfIndex.1.15 = 1015 dsx3MappingIfIndex.1. 2 = 1002 dsx3MappingIfIndex.1.16 = 1016 dsx3MappingIfIndex.1. 3 = 1003 dsx3MappingIfIndex.1.17 = 1017 dsx3MappingIfIndex.1. 4 = 1004 dsx3MappingIfIndex.1.18 = 0 dsx3MappingIfIndex.1. 5 = 1005 dsx3MappingIfIndex.1.19 = 0 dsx3MappingIfIndex.1. 6 = 1006 dsx3MappingIfIndex.1.20 = 0 dsx3MappingIfIndex.1. 7 = 1007 dsx3MappingIfIndex.1.21 = 0 dsx3MappingIfIndex.1. 8 = 1008 dsx3MappingIfIndex.1.22 = 0 dsx3MappingIfIndex.1. 9 = 1009 dsx3MappingIfIndex.1.23 = 0 dsx3MappingIfIndex.1.10 = 1010 dsx3MappingIfIndex.1.24 = 0 dsx3MappingIfIndex.1.11 = 1011 dsx3MappingIfIndex.1.25 = 0 dsx3MappingIfIndex.1.12 = 1012 dsx3MappingIfIndex.1.26 = 0 dsx3MappingIfIndex.1.13 = 1013 dsx3MappingIfIndex.1.27 = 0 dsx3MappingIfIndex.1.14 = 1014 dsx3MappingIfIndex.1.28 = 0 Note that in the case above all channels are mapped to one T3 port with ifIndex = 1. The Channels 1...28 are represented via the 2nd index. The values of 1001...1016 are the T1 interface ifIndexes. The value of 1017 is the ifIndex of the VCG. Unconnected channels have a value of 0.
INT dsx3TxClockSource	1.3.6.1.4.1.164.3.1.6.3.2.1.2	INTEGER	read-write	The source of Transmit Clock. loopTiming indicates that the recovered receive clock is used as the transmit clock. localTiming indicates that a local clock source is used or that an external clock is attached to the box containing the interface. throughTiming indicates that transmit clock is derived from the recovered receive clock of another DS3 interface. 'system' indicates that the system clock is used as the transmit clock.
dsx3XConfigEntry	1.3.6.1.4.1.164.3.1.6.3.2.1		not-accessible	An entry containing additional configuration parameters.
dsx3XConfigTable	1.3.6.1.4.1.164.3.1.6.3.2		not-accessible	An extension to the DS3 Configuration table.
NTF enrollmentTrap	1.3.6.1.4.1.164.6.1.0.12			This trap is a periodically trap, which sent to manager untill Agent get any response (Get or Set) from this manager.
INT ethAutoMdiXEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.17	INTEGER	read-write	This parameter defines whether to support automatic change between MDI and MDI[X].
INT ethBackPressure	1.3.6.1.4.1.164.3.1.6.1.1.1.5	INTEGER	read-write	This parameter defines whether to enable or disable Back pressure. Back Pressure is a flow control parameter.
INT ethBridgingMode	1.3.6.1.4.1.164.3.1.6.1.1.1.3	INTEGER	read-write	This object indicates the bridging mode of the Ethernet interface.
INT ethBroadcastBlock	1.3.6.1.4.1.164.3.1.6.1.1.1.9	INTEGER	read-write	This parameter defines whether to send broadcast message to WAN from LAN or not.
INT ethDot1xEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.23	INTEGER	read-write	Determines if the Port-Based Network Access Protocol (IEEE-802.1x) is enabled for the Ethernet Port.
INT ethDot1xPortRole	1.3.6.1.4.1.164.3.1.6.1.1.1.25	INTEGER	read-write	Determine the functionality of the port in the Port-Based Network Access Protocol (IEEE-802.1x) - either Authenticator or Supplicant.
INT ethEncapsulationCRCMode	1.3.6.1.4.1.164.3.1.6.1.1.1.4	INTEGER	read-write	This object define the encapsulation type requested for the Ethernet interface. It indicates if we transfer the Ethernet frame to the other side with or without the CRC.
MAC ethFlowCtrlMacAddress	1.3.6.1.4.1.164.3.1.6.1.1.1.14	MacAddress	read-write	In case of flow control - transmit frame with this specific MAC address to inform the other end to stop sending frames. Default: 01.80.C2.00.00.01.
ethIf	1.3.6.1.4.1.164.3.1.6.1
G32 ethIfCurrentAlignmentErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.5	Gauge32	read-only	The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentCarrierSenseErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.14	Gauge32	read-only	The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentDeferredTransmissions	1.3.6.1.4.1.164.3.1.6.1.2.1.1.12	Gauge32	read-only	The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the current interval.
ethIfCurrentEntry	1.3.6.1.4.1.164.3.1.6.1.2.1.1		not-accessible	An entry in the Ethernet Current table.
G32 ethIfCurrentFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.6	Gauge32	read-only	The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.27	Gauge32	read-only	The number of received Broadcast frames, encountered by the Ethernet interface in the current interval.
I32 ethIfCurrentIndex	1.3.6.1.4.1.164.3.1.6.1.2.1.1.1	Integer32	read-only	The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval type can indicate: 1 minute, 15 minutes, 1 hour, 24 hours. For the exact formula, see device specification.
G32 ethIfCurrentInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.29	Gauge32	read-only	The number of received Discarded frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.3	Gauge32	read-only	The counter associated with the number of received frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.25	Gauge32	read-only	The number of received Multicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.4	Gauge32	read-only	The counter associated with the number of received octets, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.31	Gauge32	read-only	The number of received Pause frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.1.1.15	Gauge32	read-only	The counter associated with the number of frames dropped due to lack of buffers in ingress pool, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.23	Gauge32	read-only	The number of received Unicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentLateCollisions	1.3.6.1.4.1.164.3.1.6.1.2.1.1.13	Gauge32	read-only	The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentLengthError	1.3.6.1.4.1.164.3.1.6.1.2.1.1.7	Gauge32	read-only	The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.11	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.28	Gauge32	read-only	The number of transmitted Broadcast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.30	Gauge32	read-only	The number of transmitted Discarded frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.8	Gauge32	read-only	The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.26	Gauge32	read-only	The number of transmitted Multicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.9	Gauge32	read-only	The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.32	Gauge32	read-only	The number of transmitted Pause frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.1.1.16	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the current interval.
G32 ethIfCurrentOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.24	Gauge32	read-only	The number of transmitted Unicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOverflowFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.19	Gauge32	read-only	The number of times the associated ethIfCurrentFCSErrors counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.37	Gauge32	read-only	The number of times the associated ethIfCurrentInBroadcastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.39	Gauge32	read-only	The number of times the associated ethIfCurrentInDiscardFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.17	Gauge32	read-only	The number of times the associated ethIfCurrentInFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.35	Gauge32	read-only	The number of times the associated ethIfCurrentInMulticastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.18	Gauge32	read-only	The number of times the associated ethIfCurrentInOctets counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.41	Gauge32	read-only	The number of times the associated ethIfCurrentInPauseFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.33	Gauge32	read-only	The number of times the associated ethIfCurrentInUnicastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.22	Gauge32	read-only	The number of times the associated ethIfCurrentMultipleCollisionFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.38	Gauge32	read-only	The number of times the associated ethIfCurrentOutBroadcastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.40	Gauge32	read-only	The number of times the associated ethIfCurrentOutDiscardFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.20	Gauge32	read-only	The number of times the associated ethIfCurrentOutFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.36	Gauge32	read-only	The number of times the associated ethIfCurrentOutMulticastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.21	Gauge32	read-only	The number of times the associated ethIfCurrentOutOctets counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.42	Gauge32	read-only	The number of times the associated ethIfCurrentOutPauseFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.34	Gauge32	read-only	The number of times the associated ethIfCurrentOutUnicastFrames counter has overflowed in the current interval.
G32 ethIfCurrentSingleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.10	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the current interval.
OCT ethIfCurrentStatus	1.3.6.1.4.1.164.3.1.6.1.2.1.1.2	OCTET STRING	read-only	The status of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
ethIfCurrentTable	1.3.6.1.4.1.164.3.1.6.1.2.1		not-accessible	The Ethernet Current table. When the index specifies the Ethernet interface (only), the counters are for an interval of 15 minutes.
ethIfEntry	1.3.6.1.4.1.164.3.1.6.1.1.1		not-accessible	An entry in table.
I32 ethIfIdx	1.3.6.1.4.1.164.3.1.6.1.1.1.1	Integer32	read-only	A unique index of the ethernet interface/port.
G32 ethIfIntervalAlignmentErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.6	Gauge32	read-only	The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the interval.
G32 ethIfIntervalCarrierSenseErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.15	Gauge32	read-only	The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalDeferredTransmissions	1.3.6.1.4.1.164.3.1.6.1.2.2.1.13	Gauge32	read-only	The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the interval.
ethIfIntervalEntry	1.3.6.1.4.1.164.3.1.6.1.2.2.1		not-accessible	An entry in the Ethernet Interval table.
G32 ethIfIntervalFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.7	Gauge32	read-only	The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.28	Gauge32	read-only	The number of received Broadcast frames, encountered by the Ethernet interface in the interval.
I32 ethIfIntervalIndex	1.3.6.1.4.1.164.3.1.6.1.2.2.1.1	Integer32	read-only	The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval type can indicate: 1 minute, 15 minutes, 1 hour, 24 hours. For the exact formula, see device specification.
G32 ethIfIntervalInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.30	Gauge32	read-only	The number of received Discarded frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.4	Gauge32	read-only	The counter associated with the number of received frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.26	Gauge32	read-only	The number of received Multicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.5	Gauge32	read-only	The counter associated with the number of received octets, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.32	Gauge32	read-only	The number of received Pause frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.2.1.16	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Receive direction to the Ethernet interface in the interval.
G32 ethIfIntervalInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.24	Gauge32	read-only	The number of received Unicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalLateCollisions	1.3.6.1.4.1.164.3.1.6.1.2.2.1.14	Gauge32	read-only	The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalLengthError	1.3.6.1.4.1.164.3.1.6.1.2.2.1.8	Gauge32	read-only	The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.12	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the interval.
I32 ethIfIntervalNumber	1.3.6.1.4.1.164.3.1.6.1.2.2.1.2	Integer32	read-only	The Interval Number. This number is between 1 and x, where 1 is the most recently completed interval and x is the least recently completed interval. For 15 minute intervals, usually x=96, but it can be different, depending on device capabilities.
G32 ethIfIntervalOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.29	Gauge32	read-only	The number of transmitted Broadcast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.31	Gauge32	read-only	The number of transmitted Discarded frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.9	Gauge32	read-only	The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.27	Gauge32	read-only	The number of transmitted Multicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.10	Gauge32	read-only	The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.33	Gauge32	read-only	The number of transmitted Pause frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.2.1.17	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the interval.
G32 ethIfIntervalOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.25	Gauge32	read-only	The number of transmitted Unicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOverflowFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.20	Gauge32	read-only	The number of times the associated ethIfIntervalFCSErrors counter has overflowed in the interval.
G32 ethIfIntervalOverflowInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.38	Gauge32	read-only	The number of times the associated ethIfIntervalInBroadcastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.40	Gauge32	read-only	The number of times the associated ethIfIntervalInDiscardFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.18	Gauge32	read-only	The number of times the associated ethIfIntervalInFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.36	Gauge32	read-only	The number of times the associated ethIfIntervalInMulticastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.19	Gauge32	read-only	The number of times the associated ethIfIntervalInOctets counter has overflowed in the interval.
G32 ethIfIntervalOverflowInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.42	Gauge32	read-only	The number of times the associated ethIfIntervalInPauseFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.34	Gauge32	read-only	The number of times the associated ethIfIntervalInUnicastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.23	Gauge32	read-only	The number of times the associated ethIfIntervalMultipleCollisionFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.39	Gauge32	read-only	The number of times the associated ethIfIntervalOutBroadcastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.41	Gauge32	read-only	The number of times the associated ethIfIntervalOutDiscardFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.21	Gauge32	read-only	The number of times the associated ethIfIntervalOutFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.37	Gauge32	read-only	The number of times the associated ethIfIntervalOutMulticastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.22	Gauge32	read-only	The number of times the associated ethIfIntervalOutOctets counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.43	Gauge32	read-only	The number of times the associated ethIfIntervalOutPauseFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.35	Gauge32	read-only	The number of times the associated ethIfIntervalOutUnicastFrames counter has overflowed in the interval.
G32 ethIfIntervalSingleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.11	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the interval.
OCT ethIfIntervalStatus	1.3.6.1.4.1.164.3.1.6.1.2.2.1.3	OCTET STRING	read-only	The status of the interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
ethIfIntervalTable	1.3.6.1.4.1.164.3.1.6.1.2.2		not-accessible	The Ethernet Interval table. When ethIfIntervalIndex specifies the Ethernet interface (only), the counters are for an interval of 15 minutes.
NTF ethIfMacAccessViolation	1.3.6.1.4.1.164.3.1.6.1.7.0.1			This trap indicates that an Access Violation occurred.
ethIfMacLayer	1.3.6.1.4.1.164.3.1.6.1.7
ethIfMacLayerEvents	1.3.6.1.4.1.164.3.1.6.1.7.0
ethIfOamCfm	1.3.6.1.4.1.164.3.1.6.1.3
ethIfOamCfmEvents	1.3.6.1.4.1.164.3.1.6.1.3.0
ethIfOamEfm	1.3.6.1.4.1.164.3.1.6.1.6
ethIfPerfEntry	1.3.6.1.4.1.164.3.1.6.1.2.4.1		not-accessible	An entry in the Ethernet Performance table.
G32 ethIfPerfInOkFrames	1.3.6.1.4.1.164.3.1.6.1.2.4.1.1	Gauge32	read-only	The counter associated with the number of received OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
G32 ethIfPerfInOkOctets	1.3.6.1.4.1.164.3.1.6.1.2.4.1.4	Gauge32	read-only	The counter associated with the number of received OK Octets, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
ethIfPerformance	1.3.6.1.4.1.164.3.1.6.1.2
G32 ethIfPerfOutOkFrames	1.3.6.1.4.1.164.3.1.6.1.2.4.1.2	Gauge32	read-only	The counter associated with the number of transmitted OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
ethIfPerfTable	1.3.6.1.4.1.164.3.1.6.1.2.4		not-accessible	The Ethernet Performance table.
G32 ethIfPerfTotalCollisions	1.3.6.1.4.1.164.3.1.6.1.2.4.1.3	Gauge32	read-only	The counter associated with the total number of collisions of any type encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done
ethIfRing	1.3.6.1.4.1.164.3.1.6.1.4
INT ethIfRingAdminStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.2	INTEGER	read-write	This object denotes the Ethernet Ring administrative status.
ethIfRingEntry	1.3.6.1.4.1.164.3.1.6.1.4.1.1		not-accessible	An entry in the table.
ethIfRingEvents	1.3.6.1.4.1.164.3.1.6.1.4.0
U32 ethIfRingIdx	1.3.6.1.4.1.164.3.1.6.1.4.1.1.1	Unsigned32	not-accessible	This object is an Index that can indicate Slot, Ring, Cnfg etc., according to the device used. When NA, 1 will be used.
U32 ethIfRingKeepAliveInterval	1.3.6.1.4.1.164.3.1.6.1.4.1.1.5	Unsigned32	read-write	This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
U32 ethIfRingKeepAliveThresh	1.3.6.1.4.1.164.3.1.6.1.4.1.1.6	Unsigned32	read-write	This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
U32 ethIfRingKeepAliveVlanId	1.3.6.1.4.1.164.3.1.6.1.4.1.1.7	Unsigned32	read-write	Dedicated VLAN ID for keep alive messages.
U32 ethIfRingMultiCastVlanId	1.3.6.1.4.1.164.3.1.6.1.4.1.1.8	Unsigned32	read-write	Dedicated VLAN ID for multicast messages.
INT ethIfRingOperStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.4	INTEGER	read-only	This object indicates the Ethernet Ring operational status.
POR ethIfRingPorts	1.3.6.1.4.1.164.3.1.6.1.4.1.1.3	PortList	read-write	The set of ports which are assigned to be ring members. The default value of this object is a string of zeros.
INT ethIfRingRowStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.9	INTEGER	read-write	Implement creation/deletion of rings in the device.
NTF ethIfRingStatusChange	1.3.6.1.4.1.164.3.1.6.1.4.0.1			This trap indicates that the status of the Ethernet Ring has been changed.
ethIfRingTable	1.3.6.1.4.1.164.3.1.6.1.4.1		not-accessible	Ethernet Ring Table.
INT ethIfSrcMacCtrl	1.3.6.1.4.1.164.3.1.6.1.7.1.1.3	INTEGER	read-write	Enable or disable the source MAC control on the current interface. The device should not enable source MAC control if for the current interface there are more than ethIfSrcMacCtrlMaxPermitAddr addresses in the ethIfSrcMacCtrlAddrTable. Default value will be: disable (2).
MAC ethIfSrcMacCtrlAddr	1.3.6.1.4.1.164.3.1.6.1.7.2.1.2	MacAddress	not-accessible	A unicast source MAC address that was learned or statically configured for the current interface. Packets with this source MAC address will be accepted by the device.
ethIfSrcMacCtrlAddrEntry	1.3.6.1.4.1.164.3.1.6.1.7.2.1		not-accessible	An entry in the table.
U32 ethIfSrcMacCtrlAddrIdx3	1.3.6.1.4.1.164.3.1.6.1.7.2.1.3	Unsigned32	not-accessible	A third index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.
U32 ethIfSrcMacCtrlAddrIndex	1.3.6.1.4.1.164.3.1.6.1.7.2.1.1	Unsigned32	not-accessible	The index of the interface for which the source MAC addresses exist in this table. It may be the ifIndex of the ETH/Bridge Port.
INT ethIfSrcMacCtrlAddrRowStatus	1.3.6.1.4.1.164.3.1.6.1.7.2.1.4	INTEGER	read-write	This MIB object will be used in order to create/delete a static row or delete an address that is not allowed to access the current interface (ethIfSrcMacCtrlAddrStatus= invalid(2)). Device will add the learned addresses to this table. It will not be possible to add a new static entry to this table while the number of existing rows is equal or more than ethIfSrcMacCtrlMaxPermitAddr. When ethIfSrcMacCtrl = enabled (3), the device will add learned entries only up to ethIfSrcMacCtrlMaxPermitAddr.
INT ethIfSrcMacCtrlAddrStatus	1.3.6.1.4.1.164.3.1.6.1.7.2.1.5	INTEGER	read-only	The status of this entry. The meanings of the values are: invalid (2) - the current address is not allowed to access this interface. learned(3) - the current address was learned. mgmt (5) - the current address is static. It may exist in the MAC Table.
ethIfSrcMacCtrlAddrTable	1.3.6.1.4.1.164.3.1.6.1.7.2		not-accessible	This table shows which MAC Addresses are permitted when the source MAC control is enabled and which non permitted MAC Addresses attempted to access the current interface. It contains static source MAC Addresses as well as learned MAC Addresses. The user can configure Static permitted source MAC Addresses via this table.
U32 ethIfSrcMacCtrlAging	1.3.6.1.4.1.164.3.1.6.1.7.1.1.7	Unsigned32	read-write	The timeout period in seconds for aging out dynamically learned source MAC addresses. Valid Values: 0 - disable 10-1000000
U32 ethIfSrcMacCtrlCurNumPermitAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.5	Unsigned32	read-only	This is the number of source MAC addresses currently permitted for the current interface.
ethIfSrcMacCtrlEntry	1.3.6.1.4.1.164.3.1.6.1.7.1.1		not-accessible	An entry in the table.
INT ethIfSrcMacCtrlFlushAddrCmd	1.3.6.1.4.1.164.3.1.6.1.7.1.1.6	INTEGER	read-write	When set to on (3) this command will erase all the learned addresses and invalid addresses of the selected interface in the ethIfSrcMacCtrlAddrTable. After operation is finished, Agent will turn the value to 'off'.
U32 ethIfSrcMacCtrlIdx2	1.3.6.1.4.1.164.3.1.6.1.7.1.1.2	Unsigned32	not-accessible	A second index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.
U32 ethIfSrcMacCtrlIndex	1.3.6.1.4.1.164.3.1.6.1.7.1.1.1	Unsigned32	not-accessible	The index of the MAC Layer interface supporting source MAC control feature. It may be the ifIndex of the ETH/Bridge Port.
MAC ethIfSrcMacCtrlLastViolatingAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.10	MacAddress	read-write	This object indicates the last MAC address that violated the security on the current interface. If no violation, the agent will return: 00-00-00-00-00-00 .
INT ethIfSrcMacCtrlLocking	1.3.6.1.4.1.164.3.1.6.1.7.1.1.8	INTEGER	read-write	When set to lock (3) this command will lock the Source MAC Address learning. No more learned addresses will be added to the ethIfSrcMacCtrlAddrTable. When set to unlock (2) this command will unlock the Source MAC Address learning. Learned addresses will be added to the ethIfSrcMacCtrlAddrTable but the number of addresses in the table will not exceed ethIfSrcMacCtrlMaxPermitAddr. Default value is: unlock (2).
U32 ethIfSrcMacCtrlMaxPermitAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.4	Unsigned32	read-write	This is the maximum number of permitted MAC addresses (static and learned) for the current interface.
INT ethIfSrcMacCtrlPortStatus	1.3.6.1.4.1.164.3.1.6.1.7.1.1.11	INTEGER	read-only	This object represents the operational status of the MAC Control feature on an interface. shutdown(2) - This indicates that the port is shutdown due to security violation. secureActive (3) - This indicates that the MAC Control interface security is operational and this interface is not shutdown due to security violation. secureInactive (4)- This indicates that the MAC Control is not operational.
ethIfSrcMacCtrlTable	1.3.6.1.4.1.164.3.1.6.1.7.1		not-accessible	This table supports source MAC addresses control parameters per interface. Source MAC control will be used mainly for security. Only packets with certain source MAC Addresses will be allowed to access the device. The source MAC addresses can be static or learned. The static addresses will be defined by the user in another table: ethIfSrcMacCtrlAddrTable. The learned addresses will exist in the ethIfSrcMacCtrlAddrTable as well.
INT ethIfSrcMacCtrlViolationAction	1.3.6.1.4.1.164.3.1.6.1.7.1.1.9	INTEGER	read-write	Determines the action that the device will take upon security violation. drop(2) - the violating packets will be dropped. dropNotify (3)- the violating packets will be dropped and notifications will be generated. Notifications may be for example: SNMP Traps, Syslog messages and log file new entries. shutdown (4) - the interface will be forced to shut down.
U32 ethIfStormCnfgIdx	1.3.6.1.4.1.164.3.1.6.1.5.1.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
INT ethIfStormCtrlEnable	1.3.6.1.4.1.164.3.1.6.1.5.1.1.5	INTEGER	read-write	This object indicates if the Storm Controling is Enabled or Disabled for the relevant entry.
INT ethIfStormDirection	1.3.6.1.4.1.164.3.1.6.1.5.1.1.3	INTEGER	not-accessible	This object indicates the port's Storm Direction.
ethIfStormEntry	1.3.6.1.4.1.164.3.1.6.1.5.1.1		not-accessible	An entry in the table.
U32 ethIfStormIfIdx	1.3.6.1.4.1.164.3.1.6.1.5.1.1.2	Unsigned32	not-accessible	A unique index of the ethernet interface/port.
ethIfStorming	1.3.6.1.4.1.164.3.1.6.1.5
U32 ethIfStormMaxRate	1.3.6.1.4.1.164.3.1.6.1.5.1.1.6	Unsigned32	read-write	This object indicates the Maximum Rate at which Storming packets are forwarded, in Kbps.For some devices the units are PPS(Packets Per Second ) or kilobytes per second.
BIT ethIfStormPacketType	1.3.6.1.4.1.164.3.1.6.1.5.1.1.4	Bits	not-accessible	Packet Type on which Storming operations will be performed.
ethIfStormTable	1.3.6.1.4.1.164.3.1.6.1.5.1		not-accessible	Ethernet Storming Table.
ethIfTable	1.3.6.1.4.1.164.3.1.6.1.1		not-accessible	A table.
I32 ethIfUse	1.3.6.1.4.1.164.3.1.6.1.1.1.19	Integer32	read-write	This parameter defines the use of the port. 1=NET 2=USER .
INT ethJumboFrameEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.16	INTEGER	read-write	This parameter defines whether to support Jumbo Frame or not.
INT ethLimit4	1.3.6.1.4.1.164.3.1.6.1.1.1.6	INTEGER	read-write	This parameter determine the Back off algorithm mode. Every 4 following collisions the Framer will be thrown out (4 times more than usuall).
INT ethLineOam	1.3.6.1.4.1.164.3.1.6.1.1.1.20	INTEGER	read-write	This parameter defines the working mode of 802.AH OAM mechanism.
INT ethMdiXManualSwitch	1.3.6.1.4.1.164.3.1.6.1.1.1.22	INTEGER	read-write	This parameter sets the port to be MDI-X (cross-over) or MDI (straight-through). It is applicable only when ethAutoMdiXEnable = no, namely, only when the automatic MDI/MDIX crossover function is disabled.
INT ethMode	1.3.6.1.4.1.164.3.1.6.1.1.1.2	INTEGER	read-write	This object indicates the Ethernet mode of operation.
INT ethMulticastBlock	1.3.6.1.4.1.164.3.1.6.1.1.1.8	INTEGER	read-write	This parameter defines whether to send multicast message to WAN from LAN or not.
NTF ethOamCfmDefectCondition	1.3.6.1.4.1.164.3.1.6.1.3.0.1			This trap indicates that a MEP has a persistent defect condition.
ethOamService	1.3.6.1.4.1.164.3.1.6.1.3.2
I32 ethOamServiceDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.6	Integer32	read-create	This object determines the delay threshold defined for this service, in measurement unit of 0.1 msec.
I32 ethOamServiceDelayVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.7	Integer32	read-create	This object determines the delay variation threshold defined for this service, in measurement unit of 0.1 msec.
C32 ethOamServiceElapsedTime	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.14	Counter32	read-only	Indicates the time elapsed in seconds since the time the service is up.
ethOamServiceEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1		not-accessible	An entry in the table.
C32 ethOamServiceFrameLoss	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.11	Counter32	read-only	Counts the number of frames lost since the time the service is up.
U32 ethOamServiceFrameLossRatio	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.13	Unsigned32	read-only	Indicates the ratio of the lost frames since the time the service is up. The value is the ratio multiplied by 1E10. 0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).
I32 ethOamServiceFrameLossRatioThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.5	Integer32	read-create	This object determines the Frame Loss ratio threshold in exponent of 1/10. That is, a value of 4 means that the threshold is 1E-4.
C32 ethOamServiceFramesAboveDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.17	Counter32	read-only	Indicates the number of frames arrived with delay greater than the delay threshold.
C32 ethOamServiceFramesAboveDelayVar	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.19	Counter32	read-only	Indicates the number of frames arrived with delay variation greater than the delay variation threshold.
U32 ethOamServiceIdx	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.1	Unsigned32	not-accessible	This object indicates the Index of the service being accessed.
C32 ethOamServiceOverflowFrameLoss	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.12	Counter32	read-only	The number of times the associated ethOamServiceFrameLoss counter has overflowed.
C32 ethOamServiceOverflowFramesAboveDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.18	Counter32	read-only	Indicates the number of times the associated ethOamServiceFramesAboveDelay counter has overflowed.
C32 ethOamServiceOverflowFramesAboveDelayVar	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.20	Counter32	read-only	Indicates the number of times the associated ethOamServiceFramesAboveDelayVar counter has overflowed.
C32 ethOamServiceOverflowTxFrames	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.10	Counter32	read-only	The number of times the associated ethOamServiceTxFrames counter has overflowed.
INT ethOamServicePmEnable	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.4	INTEGER	read-create	This object determines PM (Performance Monitoring) shall be enabled or not for the service.
U32 ethOamServicePriority	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.3	Unsigned32	read-create	This object determines the priority of the service. It is sent as P bits in an OAM message originated by this service.
ROW ethOamServiceRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.2	RowStatus	read-create	This attribute allows to create/delete a row in this table.
ethOamServiceTable	1.3.6.1.4.1.164.3.1.6.1.3.2.1		not-accessible	Service configuration table associated with Services running on a MEP.
C32 ethOamServiceTxFrames	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.9	Counter32	read-only	Counts the number of frames trnasmitted by since the time the service is up.
U32 ethOamServiceUnavailRatio	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.16	Unsigned32	read-only	Indicates the ratio of the unavailable seconds since the time the service is up. The value is the ratio multiplied by 1E10. 0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).
I32 ethOamServiceUnavailRatioThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.8	Integer32	read-create	This object determines the Unavailability ratio threshold in exponent of 1/10. That is, a value of 4 means that the threshold is 1E-4.
C32 ethOamServiceUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.15	Counter32	read-only	Indicates the number of unavailable seconds since the time the service is up.
U32 ethOamStdEtherType	1.3.6.1.4.1.164.3.1.6.1.3.6	Unsigned32	read-write	The Standard Ether Type in an OAM message. This object will be RW until a formal value will be issued for standard Ethernet Type. When such Standard will exist, this object will be supported RO to reflect the Standard value.
MAC ethOamStdMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.7	MacAddress	read-write	The Standard MAC Address in an OAM message. This object will be RW until a formal value will be issued for standard MAC Address. When such Standard will exist, this object will be supported RO to reflect the Standard value.
U32 ethOamSvcCurrAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.9	Unsigned32	read-only	The average round trip delay in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.11	Unsigned32	read-only	The average round trip delay variation in the current interval. Values units are of 0.1 msec.
I32 ethOamSvcCurrElapsedTime	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.12	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current interval.
ethOamSvcCurrentStatEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1		not-accessible	Current Statistics per service
ethOamSvcCurrentStatTable	1.3.6.1.4.1.164.3.1.6.1.3.2.2		not-accessible	Service Current Statistics Table.
PER ethOamSvcCurrFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.1	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay greater than the threshold value defined for the service.
PER ethOamSvcCurrFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.3	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay variation greater than the threshold value defined for the service.
PER ethOamSvcCurrFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.2	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay lower than or equal to the threshold value defined for the service.
PER ethOamSvcCurrFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.4	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay variation lower than or equal to the threshold value defined for the service.
PER ethOamSvcCurrFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.6	PerfCurrentCount	read-only	Number of lost frames in the current interval.
PER ethOamSvcCurrFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.5	PerfCurrentCount	read-only	Number of trnasmitted frames in the current interval.
U32 ethOamSvcCurrMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.8	Unsigned32	read-only	The maximum value of round trip delay in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.10	Unsigned32	read-only	The maximum value of round trip delay variation in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.7	Unsigned32	read-only	The mininal value of round trip delay in the current interval. Values units are of 0.1 msec.
PER ethOamSvcCurrUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.13	PerfCurrentCount	read-only	The number of seconds that the service was unavailable in the current interval.
U32 ethOamSvcIntervalAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.10	Unsigned32	read-only	The average round trip delay in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.12	Unsigned32	read-only	The average round trip delay variation in the selected interval. Values units are of 0.1 msec.
ethOamSvcIntervalEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1		not-accessible	Interval Statistics per service
NUM ethOamSvcIntervalFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.2	PerfIntervalCount	read-only	Number of frames that arrived in a delay greater than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.4	PerfIntervalCount	read-only	Number of frames that arrived in a delay variation greater than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.3	PerfIntervalCount	read-only	Number of frames that arrived in a delay lower than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.5	PerfIntervalCount	read-only	Number of frames that arrived in a delay variation lower than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.7	PerfIntervalCount	read-only	Number of lost frames in the selected interval.
NUM ethOamSvcIntervalFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.6	PerfIntervalCount	read-only	Number of trnasmitted frames in the selected interval.
U32 ethOamSvcIntervalMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.9	Unsigned32	read-only	The maximum value of round trip delay in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.11	Unsigned32	read-only	The maximum value of round trip delay variation in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.8	Unsigned32	read-only	The mininal value of round trip delay in the selected interval. Values units are of 0.1 msec.
I32 ethOamSvcIntervalNum	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.1	Integer32	not-accessible	The Interval index, which is actualy the Interval number, where 1 is the most recently completed 15 minute interval, and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
ethOamSvcIntervalTable	1.3.6.1.4.1.164.3.1.6.1.3.2.3		not-accessible	Service Interval Statistics Table.
NUM ethOamSvcIntervalUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.13	PerfIntervalCount	read-only	The number of seconds that the service was unavailable in the selected interval.
U32 ethOamSvcTotalAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.9	Unsigned32	read-only	The average round trip delay in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.11	Unsigned32	read-only	The average round trip delay variation in the last 24H. Values units are of 0.1 msec.
ethOamSvcTotalEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1		not-accessible	Total Statistics per service
PER ethOamSvcTotalFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.1	PerfTotalCount	read-only	Number of frames that arrived in a delay greater than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.3	PerfTotalCount	read-only	Number of frames that arrived in a delay variation greater than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.2	PerfTotalCount	read-only	Number of frames that arrived in a delay lower than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.4	PerfTotalCount	read-only	Number of frames that arrived in a delay variation lower than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.6	PerfTotalCount	read-only	Number of lost frames in the last 24H.
PER ethOamSvcTotalFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.5	PerfTotalCount	read-only	Number of trnasmitted frames in the last 24H.
U32 ethOamSvcTotalMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.8	Unsigned32	read-only	The maximum value of round trip delay in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.10	Unsigned32	read-only	The maximum value of round trip delay variation in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.7	Unsigned32	read-only	The mininal value of round trip delay in the last 24H. Values units are of 0.1 msec.
ethOamSvcTotalTable	1.3.6.1.4.1.164.3.1.6.1.3.2.4		not-accessible	ETH OAM Service Total (24H) Statistics Table.
PER ethOamSvcTotalUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.12	PerfTotalCount	read-only	The number of seconds that the service was unavailable in the last 24H.
INT ethPartnerRateMode	1.3.6.1.4.1.164.3.1.6.1.1.1.24	INTEGER	read-write	For converters having couples of ports, where each couple contains a port with an SFP connector and a port with a RJ connector, this parameter is relevant for the SFP port. It affects Rate configuration of its partner (RJ port). manual - user can configure manually ETH parameters of RJ port (e.g Autonegotiation, Max Capability Advertised, etc...) automatic - SFP Rate will be enforced on the RJ port. In this mode, user cannot configure the Rate related parameters of the RJ port (e.g Autonegotiation, Max Capability Advertised, etc...)
INT ethPerformanceMode	1.3.6.1.4.1.164.3.1.6.1.2.3	INTEGER	read-write	This object indicates whether OK or Fail statistics will be counted.
INT ethPortDataEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.18	INTEGER	read-write	This parameter defines whether this port is enabled for data (that is not management). no(2) - management can run on this port yes(3) - both management and payload data can run on this port.
INT ethPortMngEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.13	INTEGER	read-write	This parameter defines whether management data can pass through this Port. localOnly (4) - Only local device can be managed via this port.
INT ethPortPriority	1.3.6.1.4.1.164.3.1.6.1.1.1.12	INTEGER	read-write	This parameter defines if priority is to be considered for this Port.
I32 ethRateLimit	1.3.6.1.4.1.164.3.1.6.1.1.1.15	Integer32	read-write	This parameter defines the Rate Limit of the line, in Mbps.
INT ethRip2	1.3.6.1.4.1.164.3.1.6.1.1.1.11	INTEGER	read-write	This parameter defines whether to send RIP II message to WAN from LAN or not
INT ethRoutingProtocol	1.3.6.1.4.1.164.3.1.6.1.1.1.21	INTEGER	read-write	This parameter defines the routing protocol used above ETH port.
INT ethSkipInitReset	1.3.6.1.4.1.164.3.1.6.1.1.1.7	INTEGER	read-write	This parameter defines whether read status on reset.
INT ethSpeed	1.3.6.1.4.1.164.3.1.6.1.1.1.10	INTEGER	read-write	This parameter defines the line speed.
U32 evcCosCnfgIdx	1.3.6.1.4.1.164.6.3.7.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
evcCosEntry	1.3.6.1.4.1.164.6.3.7.1		not-accessible	An entry in table.
U32 evcCosEvcIdx	1.3.6.1.4.1.164.6.3.7.1.2	Unsigned32	not-accessible	This attribute indicates EVC Id.
STR evcCosEvcName	1.3.6.1.4.1.164.6.3.7.1.5	SnmpAdminString	read-create	A string that identifies the EVC. It should be unique in the Maintenance Domain (i.e., in the managed network) Used as MEG ID field in OAM messages.
ROW evcCosRowStatus	1.3.6.1.4.1.164.6.3.7.1.3	RowStatus	read-create	This attribute allows to create/delete a row in this table.
U32 evcCosSpVlanId	1.3.6.1.4.1.164.6.3.7.1.6	Unsigned32	read-create	This object indicates the SP (Service Provider) VLAN used when sending an OAM message for the specified EVC.
evcCosTable	1.3.6.1.4.1.164.6.3.7		not-accessible	This table defines mapping of Ethernet Virtual Connection (EVC) ID to Class of Service (CoS) ID
NTF failedLogin	1.3.6.1.4.1.164.6.1.0.25			This trap is sent when a user tried to Login via Terminal/Telnet/Web and failed. This trap is used when the device is located at End-User's premises while management is at Service Provider's premises.
STR fileName	1.3.6.1.4.1.164.6.2.12.2	DisplayString	read-write	The name of the file to be loaded. For protection, read returns NULL.
STR fileNameWithinProduct	1.3.6.1.4.1.164.6.2.12.9	DisplayString	read-write	The file name used by the product within the product file system.
IP fileServerIP	1.3.6.1.4.1.164.6.2.12.1	IpAddress	read-write	The IP address of the server from which the file is loaded
INT fileTransCmd	1.3.6.1.4.1.164.6.2.12.3	INTEGER	read-write	The command to be executed on fileName at fileServerIP.
fileTransfer	1.3.6.1.4.1.164.6.2.12
INT fileTransferProtocol	1.3.6.1.4.1.164.6.2.12.15	INTEGER	read-write	File Transfer protocol used.
U32 fileTransferServerPort	1.3.6.1.4.1.164.6.2.12.14	Unsigned32	read-write	Server Port number used for File Transfer. Applicable for SFTP. Valid values: 0..65535.
OCT fileTransferToSubSystems	1.3.6.1.4.1.164.6.2.12.8	OCTET STRING	read-write	This object represents the sub-systems the fileTransCmd refers to. It should be used when a system is divided to sub-systems and each sub-system (or part of them) can have a different SW/Configuration. Each bit of this object will represent one of the sub-systems. Bit='1' - APPLY to respective sub-system Bit='0' - DO NOT APPLY to respective sub-system For the meaning of each bit, see product's specification. User will select the sub-systems envolved by filling-in the bits that represent these sub-systems. In this case, the file represented by 'fileName' will include several parts, each representing one of the sub-systems. The agent will refer only to the part/s indicated by this object. 0 Octet Strings = not applicable DEFVAL = 0h for the products that support this object.
NTF flipDbChangeTrap	1.3.6.1.4.1.164.3.2.0.4			This trap is sent upon change of the active Flip tables (Flip DB).
U32 flowIndex	1.3.6.1.4.1.164.6.3.6.1.1	Unsigned32	not-accessible	Defines the Flow ID the service is associated to.
flowMappingProfileEntry	1.3.6.1.4.1.164.6.3.9.1.1		not-accessible	Each entry in this table describes one Flow mapping profile with one of its Flow Mapping supported, according to the Priority order. The information includes a reference to a Flow Mapping index.
U32 flowMappingProfileIndex	1.3.6.1.4.1.164.6.3.9.1.1.1	Unsigned32	not-accessible	A running index for the Flow Mapping Profile table.
U32 flowMappingProfileMapIndex	1.3.6.1.4.1.164.6.3.9.1.1.5	Unsigned32	read-create	This attribute holds a reference to the mapping index. It specifies the mapping selected for the Mapping Profile for the selected Priority. When flowMappingProfileNumOfMaps=0, this attribute is not relevant.
STR flowMappingProfileName	1.3.6.1.4.1.164.6.3.9.1.1.6	SnmpAdminString	read-create	This attribute defines the name assigned to flowMappingIndex profile.
U32 flowMappingProfileNumOfMaps	1.3.6.1.4.1.164.6.3.9.1.1.4	Unsigned32	read-create	This attribute determines the number of the mappings associated to the Flow Mapping Profile.
INT flowMappingProfilePriority	1.3.6.1.4.1.164.6.3.9.1.1.2	INTEGER	not-accessible	The priority of the Mapping selected by flowMappingProfileMapIndex within the Flow Mapping Profile.
ROW flowMappingProfileRowStatus	1.3.6.1.4.1.164.6.3.9.1.1.3	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
flowMappingProfileTable	1.3.6.1.4.1.164.6.3.9.1		not-accessible	This table holds flow mapping profiles.
genBridge	1.3.6.1.4.1.164.4.1
genDacsMux	1.3.6.1.4.1.164.3.3.4
gfp	1.3.6.1.4.1.164.6.2.55
gfpCnfgEntry	1.3.6.1.4.1.164.6.2.55.1.1		not-accessible	An entry in the GFP configuration table.
U32 gfpCnfgIdx	1.3.6.1.4.1.164.6.2.55.1.1.1	Unsigned32	not-accessible	Index to GFP configuration table.
gfpCnfgTable	1.3.6.1.4.1.164.6.2.55.1		not-accessible	Configuration table for GFP (General Framing Protocol).
INT gfpPayloadFcs	1.3.6.1.4.1.164.6.2.55.1.1.2	INTEGER	read-write	This object defines whether protocol header will include FCS.
INT gfpRxTxScramble	1.3.6.1.4.1.164.6.2.55.1.1.3	INTEGER	read-write	This object defines whether transmission will be scrambled.
INT gfpVcatHeader	1.3.6.1.4.1.164.6.2.55.1.1.4	INTEGER	read-write	VCAT header is LCAS CONTROL packet as described in the G-7043. one control packet is transmitted in a period of 16 Multi frame
IP hostDefaultNextHop	1.3.6.1.4.1.164.6.2.40.1.4	IpAddress	read-create	The host interface Default Next Hop address.
hostEntry	1.3.6.1.4.1.164.6.2.40.1		not-accessible	An entry in the Host Table. The hostParam1, hostParam2, and hostParam3 entries may have different use in different applications.
I32 hostIndex	1.3.6.1.4.1.164.6.2.40.1.1	Integer32	not-accessible	The Host Table Index. This index can have the same value as Host No.
IP hostIP	1.3.6.1.4.1.164.6.2.40.1.2	IpAddress	read-create	The host interface IP address.
IP hostIPMask	1.3.6.1.4.1.164.6.2.40.1.3	IpAddress	read-create	The host interface subnet mask.
I32 hostMode	1.3.6.1.4.1.164.6.2.40.1.5	Integer32	read-create	This parameter represents the Host mode of operation. There can be different values for each application. For example: Not Applicable = 1.
I32 hostParam1	1.3.6.1.4.1.164.6.2.40.1.6	Integer32	read-create	This parameter represents the first Host parameter. There can be different values for each application. For example: Not Applicable = 1.
I32 hostParam2	1.3.6.1.4.1.164.6.2.40.1.7	Integer32	read-create	This parameter represents the 2nd Host parameter. There can be different values for each application.
I32 hostParam3	1.3.6.1.4.1.164.6.2.40.1.8	Integer32	read-create	This parameter represents the 3nd Host parameter. There can be different values for each application.
ROW hostRowStatus	1.3.6.1.4.1.164.6.2.40.1.9	RowStatus	read-create	Creation/Deletion of rows in the table.
hostTable	1.3.6.1.4.1.164.6.2.40		not-accessible	Host interface table.
I32 hostVlanId	1.3.6.1.4.1.164.6.2.40.1.11	Integer32	read-create	Host VLAN ID.
I32 hostVlanPriority	1.3.6.1.4.1.164.6.2.40.1.12	Integer32	read-create	Host VLAN Frame priority.
INT hostVlanTagging	1.3.6.1.4.1.164.6.2.40.1.10	INTEGER	read-create	Host VLAN support (Tagging). untag - No support of VLAN Tagging. tag - 4 VLAN bytes will be added to the frame.
I32 ifCreateConnectedTo	1.3.6.1.4.1.164.6.2.35.1.1.7	Integer32	read-create	This object indicates the entity connected to the created Interface. The value of this object can be ifIndex of the connected entity or any other number that can identify it.
NUM ifCreateConnectionPointer	1.3.6.1.4.1.164.6.2.35.1.1.9	RowPointer	read-create	This parameter represents the entity that is connected to this Interface. It can be used instead of ifCreateConnectedTo. It is an OBJECT IDENTIFIER. This parameter's SYNTAX allows the following possibilities: - can be simply used for entity that is not an interface - is not limited to include up to 32 bits The value of this parameter is a pointer to an existing row of a table, where the entity connected to this Interface is defined (i.e. the pointer uniquely identifies the connected entity). Examples: In case of an interface (from 2863.ifTable): points to 'ifEntry' of corresponding row = . In case of a VPI/VCI (from 2515.atmVclTable): points to 'atmVclEntry' of corresponding row = ..VPI.VCI In case no entity is connected, value = 0 .
I32 ifCreateEntityIdx	1.3.6.1.4.1.164.6.2.35.1.1.2	Integer32	read-only	This object indicates the Index of the Entity that exists above the created interface. For a Logical Port, this value can be: 9999 - N/A when there is no fixed entity above it.
SYS ifCreateEntityType	1.3.6.1.4.1.164.6.2.35.1.1.1	SysIfEntityType	read-only	This object indicates the Type of the Entity that exists above the created interface. For a Logical Port, this value can be: other (1) when there is no fixed entity above it.
ifCreateEntry	1.3.6.1.4.1.164.6.2.35.1.1		not-accessible	An entry in the Interface Configuration table.
I32 ifCreateIndex	1.3.6.1.4.1.164.6.2.35.1.1.6	Integer32	read-only	This object indicates the ifIndex of the created Interface. The ifIndex is assigned by the device.
I32 ifCreateNumber	1.3.6.1.4.1.164.6.2.35.1.1.3	Integer32	read-only	This object indicates the number of the Interface that is created.
U32 ifCreateParams	1.3.6.1.4.1.164.6.2.35.1.1.8	Unsigned32	read-create	This object represents one or more parameters of the created Interface. Each group of bits (one or more bits) represents a specific parameter and its possible values. This object's mapping and interpretation will be specified in each device's specification documents. The parameter should be used within the create PDU assuming atomic operation.
ROW ifCreateRowStatus	1.3.6.1.4.1.164.6.2.35.1.1.4	RowStatus	read-create	This object enables the user to create/delete entries in this table.
ifCreateTable	1.3.6.1.4.1.164.6.2.35.1		not-accessible	The Interface Configuration Table. This table enables to create interfaces of Entities.
IAN ifCreateType	1.3.6.1.4.1.164.6.2.35.1.1.5	IANAifType	read-create	This object indicates the Type of the Interface that is created.
I32 ifPerfCounterType	1.3.6.1.4.1.164.6.2.35.2.1.1.1	Integer32	not-accessible	2nd index of the ifPerfTable. This parameter represents the Counter Type. Each application can have a different association between this object's value and counter type - see relevant application spec. For VPLS-MTU application use the following values: 1= Rx Octets, 2= Tx Octets, 3= Rx Frames, 4= Tx Frames, 5=Rx Dropped Frames, 6= Tx Dropped Frames. Optionally, counter type description appears in agnListDecodingTable
ifPerfEntry	1.3.6.1.4.1.164.6.2.35.2.1.1		not-accessible	An entry in the Interface Performance Table.
C64 ifPerfHCCounter	1.3.6.1.4.1.164.6.2.35.2.1.1.4	Counter64	read-only	This High Capacity counter holds whole 64 bits of the counter indicated by ifPerfCounterType (concatenates both counter parts ifPerfHighCounterPart&ifPerfLowCounterPart) This object can be supported only by agents using SNMPv2 or SNMPv3.
U32 ifPerfHighCounterPart	1.3.6.1.4.1.164.6.2.35.2.1.1.3	Unsigned32	read-only	This parameter holds the High 32 bits of the counter (see description in the above parameter).
U32 ifPerfLowCounterPart	1.3.6.1.4.1.164.6.2.35.2.1.1.2	Unsigned32	read-only	In order to support Counters having 64 bit length, the performance counter is divided into two 32 bit parameters as follows: [ 64 bit parameter ] = [ High 32 bit parameter ][ Low 32 bit parameter ]. This parameter holds the Low 32 bits of the counter, while the following parameter holds the High 32 bits of the counter.
ifPerfTable	1.3.6.1.4.1.164.6.2.35.2.1		not-accessible	Interface Performance Table. The propose of this table is to support statistics counters having 64 bit by using 2 parameters with syntax= Integer32. This is because SNMPv1 does not support Counter64 properly. For SNMPv3, ifPerfHCCounter (Counter64) may be supported.
ifTeQos	1.3.6.1.4.1.164.6.3.3
ifTeQosEntry	1.3.6.1.4.1.164.6.3.3.1.1		not-accessible	An entry in the TE QOS Interface table.
I32 ifTeQosIdx1	1.3.6.1.4.1.164.6.3.3.1.1.1	Integer32	not-accessible	This object indicates the 1st Index of the table.
I32 ifTeQosIdx2	1.3.6.1.4.1.164.6.3.3.1.1.2	Integer32	not-accessible	This object indicates the 2nd Index of the table.
I32 ifTeQosIdx3	1.3.6.1.4.1.164.6.3.3.1.1.3	Integer32	not-accessible	This object indicates the 3rd Index of the table.
OCT ifTeQosParam	1.3.6.1.4.1.164.6.3.3.1.1.4	OCTET STRING	read-write	This object is used for QOS attributes of the entry's entities.
OCT ifTeQosParam2	1.3.6.1.4.1.164.6.3.3.1.1.5	OCTET STRING	read-write	This object is used for 2nd group QOS attributes of the entry's entities.
INT ifTeQosStatus	1.3.6.1.4.1.164.6.3.3.1.1.6	INTEGER	read-write	This object is used to create, activate and destroy entries of this table.
ifTeQosTable	1.3.6.1.4.1.164.6.3.3.1		not-accessible	The TE QOS Interface Table.
interfacePerformance	1.3.6.1.4.1.164.6.2.35.2
INT intSwdlCardType	1.3.6.1.4.1.164.6.2.12.10.1.9	INTEGER	read-only	This object defines the Card type that this file is relevant for.
INT intSwdlCmd	1.3.6.1.4.1.164.6.2.12.10.1.7	INTEGER	read-write	The command to down-load a SW file to an object. The Agent will change the value of this MIB object to off(2) automatically, after accepting the command.
intSwdlEntry	1.3.6.1.4.1.164.6.2.12.10.1		not-accessible	An entry in table.
I32 intSwdlFileIdx	1.3.6.1.4.1.164.6.2.12.10.1.2	Integer32	read-only	The index of the files included in intSwdlObjIdx. One of these files can be selected to be internally downloaded.
STR intSwdlFileName	1.3.6.1.4.1.164.6.2.12.10.1.3	DisplayString	read-only	The name of the file.
STR intSwdlFileSwVer	1.3.6.1.4.1.164.6.2.12.10.1.4	DisplayString	read-only	The software version of the file.
I32 intSwdlFlashIdx	1.3.6.1.4.1.164.6.2.12.10.1.10	Integer32	read-only	The index of the flash memory this file is stored in (1 or 2) (Example: 1= The file is stored in flash No.1). ASMi52 file will always be stored in Flash No.2 (intSwdlFlashIdx=2).
I32 intSwdlObjIdx	1.3.6.1.4.1.164.6.2.12.10.1.1	Integer32	read-only	The index of the object from which down-load is performed.
STR intSwdlSize	1.3.6.1.4.1.164.6.2.12.10.1.6	DisplayString	read-only	The size of the file.
NTF intSwdlSlotFileMismatch	1.3.6.1.4.1.164.6.1.0.5			This notification is sent when the card in the chosen slot doesn't match the chosen file. The attached object indicates the File Name.
STR intSwdlSwDate	1.3.6.1.4.1.164.6.2.12.10.1.5	DisplayString	read-only	The software version date of the file.
intSwdlTable	1.3.6.1.4.1.164.6.2.12.10		not-accessible	This parameters table is for internal Software down load. It also includes data about all files contained in the Object from which down-load is performed.
OCT intSwdlToSubSystem	1.3.6.1.4.1.164.6.2.12.10.1.8	OCTET STRING	read-write	This object defines the subsystem for download. Bit='1'- APPLY to respective sub system. Bit='0'- DO NOT APPLY to respective sub system. For more details see product specification. For every octet bit0=LSB, bit7=MSB
STR invNameXC	1.3.6.1.4.1.164.6.2.41.1.1	SnmpAdminString	not-accessible	The unique Connection name, associated to a Cross-Connection.
invNameXCEntry	1.3.6.1.4.1.164.6.2.41.1		not-accessible	An entry in the table.
I32 invNameXCIndex	1.3.6.1.4.1.164.6.2.41.1.3	Integer32	read-only	The XC Table (invNameXCType) may include more than one index. This object represents the value of the first XC Index.
invNameXCTable	1.3.6.1.4.1.164.6.2.41		not-accessible	Inverse Name XC Table. This table can be used to ease the search for a connection first index by the connection name.
OID invNameXCType	1.3.6.1.4.1.164.6.2.41.1.2	OBJECT IDENTIFIER	read-only	The OBJECT IDENTIFIER of the respective XC Table. Examples: XC Table invNameXCType --------------------------------------------------- atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .
ip2If	1.3.6.1.4.1.164.3.1.6.7
INT ip2IfAdminStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.4	INTEGER	read-create	The desired state of the link.
I32 ip2IfBandWidth	1.3.6.1.4.1.164.3.1.6.7.1.1.26	Integer32	read-create	Defines the Bandwidth of the bundle. For TDM bundles - it is the Number of Time Slots in The Bundle. - For T1 the value will be: 1..24 - For E1 the value will be: 1..31 - For T3 the value will be: 1..84 - For E3 the value will be: 1..63 This parameter is required for devices like Emux where the bandwidth of the bundles is unknown. The bundles that are received should be transmitted without any change in the bandwidth. It is the user's responsibility to enter the correct bandwidth. For Ethernet bundles - it is the bandwidth, measured in Kbps.
INT ip2IfBundleSensitivity	1.3.6.1.4.1.164.3.1.6.7.1.1.79	INTEGER	read-create	Denotes if the bundle is sensitive to delay in the network, or is sensitive to data errors in the network. Voice bundles are sensitive to delay; Non-voice bundles are sensitive to data errors.
I32 ip2IfBundleUsage	1.3.6.1.4.1.164.3.1.6.7.1.1.18	Integer32	read-only	The Bundle Resource usage in Kbps.
I32 ip2IfCallerIdDelay	1.3.6.1.4.1.164.3.1.6.7.1.1.44	Integer32	read-create	Time in msec between CLID (Caller ID) signal detection on the line and CLID signal transmission. The CLID must be sent between ringing signals and the value of the delay is used for synchronizing the CLID transmission with the ringing signals transmission. Valid values: 0 - 3000 msec.
INT ip2IfCallerIdDetection	1.3.6.1.4.1.164.3.1.6.7.1.1.91	INTEGER	read-create	Enable/Disable Caller ID Detection for this bundle.
I32 ip2IfCallerIdRxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.89	Integer32	read-create	The gain value in dBm units of the Caller ID signal received on the bundle.
I32 ip2IfCallerIdTxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.88	Integer32	read-create	The gain value in dBm units used for transmitting the Caller ID signal on the bundle.
INT ip2IfCallerIDType	1.3.6.1.4.1.164.3.1.6.7.1.1.72	INTEGER	read-create	Caller ID Type used by the DSP for this bundle. Bellcore type is used by the American method. V.23 type is used by the European method.
INT ip2IfCASRedundancy	1.3.6.1.4.1.164.3.1.6.7.1.1.78	INTEGER	read-create	Enable/Disable CAS signaling redundancy. This parameter is useful when there are problems with the network and applicable only for CAS signaling: E1-MF (G.732S) or E1-CRC-MF (G.732SCRC ). enable (3) - means that each packet containing CAS signaling will be triplicated into 3 packets. disable (2)- No redundancy will exist. Only 1 packet containing CAS will be transmitted.
U32 ip2IfCdisCngDetectionTime	1.3.6.1.4.1.164.3.1.6.7.1.1.85	Unsigned32	read-create	When working with CDIS (Call DIScrimination method) or CNG (Comfort Noise Generation): The time in msec that the device will detect 1100Hz & 2100Hz signals on the line before switching to modem or fax. For Vmux: the values will be in steps of 10 msec.
I32 ip2IfChannelIndex	1.3.6.1.4.1.164.3.1.6.7.1.1.1	Integer32	read-only	The channel index, which is actualy the bundle ID.
INT ip2IfClockPreferences	1.3.6.1.4.1.164.3.1.6.7.1.1.57	INTEGER	read-create	The Clock preferences: accurateness (2) = Accurate clock is more important than Constant Delay. constantDelay (3)= Constant Delay is more important than Accurate clock .
INT ip2IfClockSourceEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.46	INTEGER	read-create	This MIB object defines whether this bundle can be a clock source.
INT ip2IfCodingLaw	1.3.6.1.4.1.164.3.1.6.7.1.1.42	INTEGER	read-create	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links.
INT ip2IfComfortNoiseGen	1.3.6.1.4.1.164.3.1.6.7.1.1.65	INTEGER	read-create	Enable or disable Comfort Noise Generation (CNG). When this parameter is enabled and no voice payload exists on the line for some time period during the call (moments of silence), the device will generate a soft background noise which assures the user that the connection is still alive (CNG). When this parameter is disabled and no voice payload exists on the line, absolute silence will be heard (Comfort Noise will not be generated).
I32 ip2IfConnCheckPktFrequency	1.3.6.1.4.1.164.3.1.6.7.1.1.32	Integer32	read-create	Time in sec. between 2 Bundle Connectivity Check packets. Valid values: 0..60. 0 = Not Applicable.
INT ip2IfConnectionMode	1.3.6.1.4.1.164.3.1.6.7.1.1.58	INTEGER	read-create	The Connection Mode: tdmOIpCe (2) = TDMOiP (CE) = Circuit Emulation. tdmOIpCv (3)= TDMOiP (CV) = Compressed Voice.
INT ip2IfConnectivityMode	1.3.6.1.4.1.164.3.1.6.7.1.1.45	INTEGER	read-create	This MIB object shows whether to send Pings or OAM frames over the bundle.
I32 ip2IfConnPktTimeOutCycles	1.3.6.1.4.1.164.3.1.6.7.1.1.33	Integer32	read-create	No. of cycles the agent will send Bundle Connectivity packets without receiving a response from the remote device before declaring that the bundle connection to the remote side is down - Time Out. Valid values: 0..5. 0 = Not Applicable.
C32 ip2IfCurrentStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.10.1.3	Counter32	read-only	Number of seconds that the buffer overflows in the current interval. This records the count of the number of seonds the Receive (Eth to TDM) buffer overflows in the current interval.
C32 ip2IfCurrentStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.10.1.2	Counter32	read-only	Number of seconds that the buffer underflows in the current interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflows in the current interval. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
ip2IfCurrentStatEntry	1.3.6.1.4.1.164.3.1.6.7.10.1		not-accessible	IP Current Statistics per bundle
I32 ip2IfCurrentStatMaxDelayVar	1.3.6.1.4.1.164.3.1.6.7.10.1.4	Integer32	read-only	The maximum deviation from the center of the buffer (in msec) for the current interval.
U32 ip2IfCurrentStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.10.1.6	Unsigned32	read-only	The Maximum jitter buffer level (in msec) for the current interval.
U32 ip2IfCurrentStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.10.1.5	Unsigned32	read-only	The Minimum jitter buffer level (in msec) for the current interval.
C32 ip2IfCurrentStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.10.1.1	Counter32	read-only	Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the current interval.
ip2IfCurrentStatTable	1.3.6.1.4.1.164.3.1.6.7.10		not-accessible	Channels (Bundles) Current Statistics Table.
C32 ip2IfCurrentStatTxErrFrameSec	1.3.6.1.4.1.164.3.1.6.7.10.1.7	Counter32	read-only	The number of seconds in which errored frames were transmitted during the current interval. The error may be one of the following: CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.
INT ip2IfCustomToneDetect	1.3.6.1.4.1.164.3.1.6.7.1.1.43	INTEGER	read-create	Custom Tone Detection (COT) is a Control operation of a 2Khz tone detector. This tone is sent between PBX devices in order to check that the line status is OK. When the COT is enabled the device will not compress/decompress the tone. In this case, if the tone is initiated by the local PBX, the Device runs a 2Khz detector tone and once detected by the Remote Device, if the COT is enabled in the Remote Device, the Remote Device will generate a 2khz tone to the remote PBX.
INT ip2IfCustomToneFrequency	1.3.6.1.4.1.164.3.1.6.7.1.1.69	INTEGER	read-create	This is the frequency of the Custom Tone that is sent between PBXs in order to check that the line status is OK. When the Custom Tone Detection is enabled the device will not compress/decompress this tone. The custom tone that is received from the local PBX will be sent to the remote PBX with the same frequency it was received. When the Custom Tone Frequency is f1780Plus2000Hz (4), the device will not compress/decompress any tone with frequencies of 1780Hz or 2000 Hz.
OCT ip2IfDataOos	1.3.6.1.4.1.164.3.1.6.7.1.1.17	OCTET STRING	read-create	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
IP ip2IfDestAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.5	IpAddress	read-create	The destination IP address.
I32 ip2IfDestPort	1.3.6.1.4.1.164.3.1.6.7.1.1.7	Integer32	read-create	The destination Bundle at the far-end device.
U32 ip2IfDtdErlRatioCutoffQ3	1.3.6.1.4.1.164.3.1.6.7.1.1.77	Unsigned32	read-create	The DTD ERL cutoff level is used in order to determine whether the near-end is talking or not. This parameter is used by the echo canceller when echo exists and there is voice with low volume on the line. DTD means Double Talk Detection. ERL means Echo Return Loss. It is the power difference [dB] between the far-end signal to the echo returned. The cutoff level is calculated for the value entering Q.3. This value will be divided by 2^3=8 in order to get the linear ratio.
INT ip2IfDtmfDetection	1.3.6.1.4.1.164.3.1.6.7.1.1.75	INTEGER	read-create	Enable/Disable DTMF (Dual Tone Multi Frequency) detectors for this bundle.
INT ip2IfEchoCanceler	1.3.6.1.4.1.164.3.1.6.7.1.1.41	INTEGER	read-create	Echo canceler activation.
ip2IfEntry	1.3.6.1.4.1.164.3.1.6.7.1.1		not-accessible	Application layer configuration per link
INT ip2IfEthSwitchMode	1.3.6.1.4.1.164.3.1.6.7.13	INTEGER	read-write	This parameter defines whether Eth Switch is in VLAN Tagged mode.
I32 ip2IfExitChannel	1.3.6.1.4.1.164.3.1.6.7.1.1.66	Integer32	read-create	The channelized bundle that the voice bundle exits through. In Gmux2000 it is the ifIndex of the Channelized Bundle (sub-channel) that the Voice Bundle exits through. The ifIndex contains the Slot+Prt+Channelized Bundle No.
INT ip2IfExitPort	1.3.6.1.4.1.164.3.1.6.7.1.1.15	INTEGER	read-create	This object determines to which external port the traffic will be sent. auto - the device will decide automatically the exit port. If there is an option for Tx via more than one ETH card then use ext1 (1) and ext2(2) for ETH card #1 (ex. LAN1 or Ggabit-ETH1) and use card2Ext1(5) and card2Ext2(6) for card #2 (ex. LAN1 or Ggabit-ETH1). In Vmux-110/210 ext5 is used for ETH-NET, ext 6 is used for E1/T1 link and ext7 is used for Serial Link. In Vmux-2100 Main Board: ext 5 is used for ETH-NET, ext 6 is used for E1/T1 link A, prtE1T1B is used for E1/T1 link B and prtEthUser is used for ETH-User. prt17(10) - prt20(13) values were added in order to support Gmux2000 VMX Card.
I32 ip2IfFarEndTdmStatus	1.3.6.1.4.1.164.3.1.6.7.7.1.14	Integer32	read-only	This variable indicates the Status of the Far-End TDM Line. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The farEndTdmNoDefect must be set if and only if no other flag is set. The various bit positions are: 1 farEndTdmNoDefect 2 farEndTdmAIS Alarm Indication Signal 4 farEndTdmRDI Remote Defect Indication
INT ip2IfFarEndType	1.3.6.1.4.1.164.3.1.6.7.1.1.23	INTEGER	read-create	This object defines the type of the Far-End device. This data is important for signaling and DS0 format. For Vmux: e1 (2) value is used for a PBX in the Far End. fxs (5) is used for Phone. Other values are not used.
C32 ip2IfIntervalStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.11.1.4	Counter32	read-only	Number of seconds that the buffer overflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer overflows in the selected interval.
C32 ip2IfIntervalStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.11.1.3	Counter32	read-only	Number of seconds that the buffer underflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflows in the selected interval. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
ip2IfIntervalStatEntry	1.3.6.1.4.1.164.3.1.6.7.11.1		not-accessible	IP Interval Statistics per bundle
I32 ip2IfIntervalStatIndex	1.3.6.1.4.1.164.3.1.6.7.11.1.1	Integer32	read-only	The Interval index, which is actualy the Interval number.
I32 ip2IfIntervalStatMaxDelayVar	1.3.6.1.4.1.164.3.1.6.7.11.1.5	Integer32	read-only	The maximum size of the buffer (in 10's of usec) in the selected interval.
U32 ip2IfIntervalStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.11.1.7	Unsigned32	read-only	The Maximum jitter buffer level (in msec) for the selected interval.
U32 ip2IfIntervalStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.11.1.6	Unsigned32	read-only	The Minimum jitter buffer level (in msec) for the selected interval.
C32 ip2IfIntervalStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.11.1.2	Counter32	read-only	Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the selected interval.
ip2IfIntervalStatTable	1.3.6.1.4.1.164.3.1.6.7.11		not-accessible	Channels (Bundles) Interval Statistics Table.
C32 ip2IfIntervalStatTxErrFrameSec	1.3.6.1.4.1.164.3.1.6.7.11.1.8	Counter32	read-only	The number of seconds in which errored frames were transmitted during the selected interval. The error may be one of the following: CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.
I32 ip2IfJitterBuffer	1.3.6.1.4.1.164.3.1.6.7.1.1.9	Integer32	read-create	The maximum cell arrival jitter in 10 usec that the reassembly process will tolerate in the cell stream, without producing errors on the CBR service interface. For KM2100: KML.11 - The range that will be used is 3...300 msec in steps of 1 msec. For Vmux: The range that will be used is 20...100 msec in steps of 10 msec.
INT ip2IfLogEvents	1.3.6.1.4.1.164.3.1.6.7.12	INTEGER	read-write	This parameter defines whether all Jitter Buffer and Sequence Number events will enter to Log File, or enter those events to Log file in one minute steps.
MAC ip2IfMacAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.8	MacAddress	read-create	The Destination MAC address of the next hop or destination station.
U32 ip2IfMaxGprsTxQueue	1.3.6.1.4.1.164.3.1.6.7.1.1.82	Unsigned32	read-create	Max GPRS Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on the network. High buffer size allows to store this burst and not lose packets.
I32 ip2IfMaxRelayModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.68	Integer32	read-create	Maximum Relay modem calls for this bundle.
U32 ip2IfMaxTxQueue	1.3.6.1.4.1.164.3.1.6.7.1.1.81	Unsigned32	read-create	Max Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on the network. High buffer size allows to store this burst and not lose packets.
I32 ip2IfMaxVBDModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.67	Integer32	read-create	Maximum VBD modem calls for this bundle.
I32 ip2IfMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.1.1.27	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
INT ip2IfMfcSpoofing	1.3.6.1.4.1.164.3.1.6.7.1.1.53	INTEGER	read-create	This MIB object defines whether the MFC (Multi Frequency Compelled) protocol spoofing will exist in the bundle. When the MFC Spoofing is used, the Local and Remote PBXs will send MFC Signaling to each other. The Vmuxes between the PBXs will send proprietary signaling to each other. They will however create and send MFC tones to their local PBX. The PBXs will not know that the actual signaling was not sent from a PBX but from a Vmux.
INT ip2IfMfRelay	1.3.6.1.4.1.164.3.1.6.7.1.1.34	INTEGER	read-create	Multi Frequency Signaling Detection.
I32 ip2IfMinPowerLevel	1.3.6.1.4.1.164.3.1.6.7.1.1.40	Integer32	read-create	Indicates the minimum power level in dBm of the MF (Multi Frequency) tone transmitted by the switch. Valid values: -1...-35 dBm.
I32 ip2IfMinPulseWidth	1.3.6.1.4.1.164.3.1.6.7.1.1.39	Integer32	read-create	Indicates the minimum width in milliseconds of the MF (Multi Frequency) tone transmitted by the switch. Valid values: 45-300 msec. notApplicable=0.
INT ip2IfModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.38	INTEGER	read-create	This MIB object shows whether Modem Calls are enabled via the bundle. relay option (3) means that the bundle will send to the network only modulated data.
OCT ip2IfModemProtocolMode	1.3.6.1.4.1.164.3.1.6.7.1.1.84	OCTET STRING	read-create	This octet string contains the mode of each Modem Protocol used on the bundle. For each protocol one octet will be used. Octet #1 will be used for V.22 Protocol. Octet #2, #3, #4... are reserved for future protocols. Octet #1 values: 0 - Not Applicable 1 - VBD: Voice Band Data. 2 - Relay: Pulse Code Modulated (PCM) data is sent via the bundle. For V.22: This MIB object is relevant only when ip2IfModemCalls = relay (4).
I32 ip2IfMplsRxLabel	1.3.6.1.4.1.164.3.1.6.7.1.1.49	Integer32	read-create	This MIB object defines the MPLS Rx. Label for this Bundle.
INT ip2IfMplsRxLabelEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.48	INTEGER	read-create	This MIB object defines whether there is user defined inner (Rx.) label for this Bundle.
I32 ip2IfMplsTxExpBits	1.3.6.1.4.1.164.3.1.6.7.1.1.52	Integer32	read-create	The MPLS Network priority (EXP bits) used for this bundle.
I32 ip2IfMplsTxLabel	1.3.6.1.4.1.164.3.1.6.7.1.1.51	Integer32	read-create	This MIB object defines the MPLS Tx. Label for this Bundle.
INT ip2IfMplsTxLabelEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.50	INTEGER	read-create	This MIB object defines whether there is user defined outer (Tx.) label for this Bundle.
INT ip2IfNetworkType	1.3.6.1.4.1.164.3.1.6.7.1.1.47	INTEGER	read-create	This MIB object defines the network over which the Bundle PSN (Packet Switching Network)is transported. In Gmux2000: ipComprHeader indicates proprietary compressed IP header packets. mplsComprHeader indicates proprietary compressed MPLS header packets.
IP ip2IfNextHop	1.3.6.1.4.1.164.3.1.6.7.1.1.6	IpAddress	read-create	The next hop to which the frame should be sent. Default value - 0.0.0.0. Upon setting the default value the frame is sent to the default Gateway.
INT ip2IfNextHopType	1.3.6.1.4.1.164.3.1.6.7.1.1.55	INTEGER	read-create	This MIB object defines the Bundle next Hop Address Type.
U32 ip2IfNlpCutoffLevel	1.3.6.1.4.1.164.3.1.6.7.1.1.76	Unsigned32	read-create	Non Linear Processor (NLP) Cutoff Level for this bundle. This parameter is used by the echo canceller. It is the maximum absolute linear PCM amplitude of the near-end signal that will cause the NLP module to be active and to mute low level residual echo & noisy surroundings.
INT ip2IfNoiseLevelForVAD	1.3.6.1.4.1.164.3.1.6.7.1.1.56	INTEGER	read-create	This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to handle.
OCT ip2IfOAM	1.3.6.1.4.1.164.3.1.6.7.1.1.19	OCTET STRING	read-create	This parameter determine the OAM configuration. The LSB (Bit 0 the most right one) is used for OAM connectivity. Values: 0 = disable, 1= enable.
INT ip2IfOAMBundleIdent	1.3.6.1.4.1.164.3.1.6.7.1.1.80	INTEGER	read-create	Denotes if an OAM bundle is identified according to the Bundle Number (0x3fff), or according to the value of the first nibble in the VCCV control word sent in the frame. controlWord - applicable only when ip2IfProtocolVersion = v2(2). When ip2IfProtocolVersion = v1(1), only bundleNumber is applicable.
INT ip2IfOnHookDetect	1.3.6.1.4.1.164.3.1.6.7.1.1.64	INTEGER	read-create	Enables or disable immediate reaction to On-Hook bits from network in Ringing.
INT ip2IfOosTxEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.31	INTEGER	read-create	This object defines whether OOS will be Transmitted. Note that for IPmux1000 the Lbit is always sent, but the OOS will be sent according to user selection in this parameter.
INT ip2IfOperStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.3	INTEGER	read-only	The actual link status. remoteFail - No Rx. localFail - No Tx. unavailable - No echo replay or replay with invalid code or when connection is in Test state. valiodationFail - Connection is in not valid state. standby - offline (can be in pre-sync mode). tdmFail - oper status is down cause of failure in the tdm. hwMismatch - the bundle exists on a card that is not installed or has a different type than the programmed card.
INT ip2IfPayloadType	1.3.6.1.4.1.164.3.1.6.7.1.1.28	INTEGER	read-create	This object defines the TDMoIP payload type.
INT ip2IfPeerAddrType	1.3.6.1.4.1.164.3.1.6.7.1.1.73	INTEGER	read-create	This MIB object defines the peer Address Type.
ip2IfPortEntry	1.3.6.1.4.1.164.3.1.6.7.9.1		not-accessible	Application layer configuration per Port
I32 ip2IfPortIndex	1.3.6.1.4.1.164.3.1.6.7.9.1.1	Integer32	read-only	The Port index, which is actualy the ifIndex.
INT ip2IfPortMask	1.3.6.1.4.1.164.3.1.6.7.9.1.3	INTEGER	read-write	This parameter defines whether Agent will mask port's alarms and statistics or not.
ip2IfPortTable	1.3.6.1.4.1.164.3.1.6.7.9		not-accessible	Port Table.
I32 ip2IfPortTotalThroughput	1.3.6.1.4.1.164.3.1.6.7.9.1.4	Integer32	read-only	This parameter indicates the total Throughput of the port in bps.
I32 ip2IfPortUsage	1.3.6.1.4.1.164.3.1.6.7.9.1.2	Integer32	read-only	This parameter indicates the usage of the port (percents).
INT ip2IfProtocolVersion	1.3.6.1.4.1.164.3.1.6.7.1.1.29	INTEGER	read-create	This object defines the TDMoIP protocol Version.
INT ip2IfPulseMeter	1.3.6.1.4.1.164.3.1.6.7.1.1.61	INTEGER	read-create	Enables or disable Pulse metering synthesis.
INT ip2IfPulseMeterFreq	1.3.6.1.4.1.164.3.1.6.7.1.1.62	INTEGER	read-create	Frequency of synthesized pulse metering for this bundle.
I32 ip2IfPulseMeterPeriod	1.3.6.1.4.1.164.3.1.6.7.1.1.63	Integer32	read-create	Duration of synthesized pulse metering. current values are: 100-250.
I32 ip2IfRateLimit	1.3.6.1.4.1.164.3.1.6.7.8	Integer32	read-write	The maximum rate permitted to transfer via the network portin Mbps.
INT ip2IfRdnState	1.3.6.1.4.1.164.3.1.6.7.1.1.24	INTEGER	read-only	This object defines the role this bundle plays in the redundancy scheme: none(2) - means this bundle is not part of redundancy pair. primary/ secondary - means this bundle is not part of redundancy pair, and that is the primary bundle or the secondary bunle.
INT ip2IfReversePolarity	1.3.6.1.4.1.164.3.1.6.7.1.1.60	INTEGER	read-create	Enables or disable Reverse polarity synthesis.
INT ip2IfRingBack	1.3.6.1.4.1.164.3.1.6.7.1.1.59	INTEGER	read-create	Enables or disable Ring Back.
ROW ip2IfRowStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.2	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table.
I32 ip2IfRxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.71	Integer32	read-create	Receive gain in dBm.
IP ip2IfSourceAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.25	IpAddress	read-create	Source IP Address of the bundle.
I32 ip2IfSrcPort	1.3.6.1.4.1.164.3.1.6.7.1.1.37	Integer32	read-create	The source Bundle at the local device, this parameter used for cases where there is no match between ip2IfChannelIndex and the Source Bundle ID.
U32 ip2IfStatAvrRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.24	Unsigned32	read-only	The avarage Round Trip delay (in msec). 0= not applicable.
I32 ip2IfStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.7.1.4	Integer32	read-only	Number of events that the buffer overflows. This records the count of the number of events the Receive (Eth to TDM) buffer overflows.
I32 ip2IfStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.7.1.3	Integer32	read-only	Number of events that the buffer underflows. This records the count of the number of events the Receive (Eth to TDM) buffer underflows. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
I32 ip2IfStatChIndex	1.3.6.1.4.1.164.3.1.6.7.7.1.1	Integer32	read-only	The channel index, which is actualy the bundle ID.
ip2IfStatEntry	1.3.6.1.4.1.164.3.1.6.7.7.1		not-accessible	IP Statistics per bundle
C32 ip2IfStatFrameTrackDupDrop	1.3.6.1.4.1.164.3.1.6.7.7.1.25	Counter32	read-only	The number of packets dropped due to being duplicated. (duplicated packet means a packet that has the same sequential number as a packet being received previously).
I32 ip2IfStatFrameTrackLongSerMiss	1.3.6.1.4.1.164.3.1.6.7.7.1.27	Integer32	read-only	The longest series of consecutive missing sequential numbers. Missing sequential numbers represent missing packets that was expected to be received successively.
C32 ip2IfStatFrameTrackMissing	1.3.6.1.4.1.164.3.1.6.7.7.1.26	Counter32	read-only	The number of packets that are missing. (Missing packet means an expected packet- according to the current sequential number - that was not received).
C32 ip2IfStatHdlcAbort	1.3.6.1.4.1.164.3.1.6.7.7.1.34	Counter32	read-only	This counter indicates the number of received HDLC frames with abort indication.
C32 ip2IfStatHdlcAlignErr	1.3.6.1.4.1.164.3.1.6.7.7.1.31	Counter32	read-only	This counter indicates the number of received HDLC frames with alignment errors.
C32 ip2IfStatHdlcCrcErr	1.3.6.1.4.1.164.3.1.6.7.7.1.30	Counter32	read-only	This counter indicates the number of received HDLC frames with CRC errors.
C32 ip2IfStatHdlcErroredFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.36	Counter32	read-only	Number of received errored HDLC frames.
C32 ip2IfStatHdlcOversize	1.3.6.1.4.1.164.3.1.6.7.7.1.32	Counter32	read-only	This counter indicates the number of received HDLC frames longer than 1470.
C32 ip2IfStatHdlcUndersize	1.3.6.1.4.1.164.3.1.6.7.7.1.33	Counter32	read-only	This counter indicates the number of received HDLC frames shorter than 4.
U32 ip2IfStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.7.1.18	Unsigned32	read-only	The Maximum jitter buffer level (in msec).
U32 ip2IfStatMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.23	Unsigned32	read-only	The maximum Round Trip delay (in msec). 0= not applicable.
U32 ip2IfStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.7.1.17	Unsigned32	read-only	The Minimum jitter buffer level (in msec).
U32 ip2IfStatMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.22	Unsigned32	read-only	The minimum Round Trip delay (in msec). 0= not applicable.
C32 ip2IfStatPsnReorderFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.21	Counter32	read-only	Number of times that Frames had been reordered in PSN.
C32 ip2IfStatPsnRxFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.16	Counter32	read-only	Number of frames that were recieved from PSN.
C32 ip2IfStatPsnSeqErrors	1.3.6.1.4.1.164.3.1.6.7.7.1.20	Counter32	read-only	Number of times that the sequence number of an incoming Frame indicates Loss of Frame or Out of order occured in PSN.
C32 ip2IfStatPsnTxFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.15	Counter32	read-only	Number of frames that were transmitted to PSN.
C32 ip2IfStatRdnFlip	1.3.6.1.4.1.164.3.1.6.7.7.1.13	Counter32	read-only	Number of redundancy flips occured. This parameter counts only flips from this bundle to the other bundle in the redundancy couple.
U32 ip2IfStatRecommendedJittBufSize	1.3.6.1.4.1.164.3.1.6.7.7.1.19	Unsigned32	read-only	The Recommended jitter buffer Size (in msec). 0= not applicable.
C32 ip2IfStatRxCorrectFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.35	Counter32	read-only	Number of received correct frames.
C32 ip2IfStatRxHdlc	1.3.6.1.4.1.164.3.1.6.7.7.1.9	Counter32	read-only	Number of HDLC frames that were received.
I32 ip2IfStatRxMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.7.1.29	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the received payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
C32 ip2IfStatRxSignaling	1.3.6.1.4.1.164.3.1.6.7.7.1.7	Counter32	read-only	Number of signaling frames that were received.
C32 ip2IfStatRxVoice	1.3.6.1.4.1.164.3.1.6.7.7.1.8	Counter32	read-only	Number of voice frames that were received.
I32 ip2IfStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.7.1.2	Integer32	read-only	Number of events that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state.
ip2IfStatTable	1.3.6.1.4.1.164.3.1.6.7.7		not-accessible	Channels (Bundles) Statistics Table.
C32 ip2IfStatTxHdlc	1.3.6.1.4.1.164.3.1.6.7.7.1.12	Counter32	read-only	Number of HDLC frames that were transmitted.
I32 ip2IfStatTxMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.7.1.28	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
C32 ip2IfStatTxOnMaxSize	1.3.6.1.4.1.164.3.1.6.7.7.1.6	Counter32	read-only	Number of frames that were transmitted due to reaching max. frame size. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing time interval elapses.
C32 ip2IfStatTxOnTimeInterval	1.3.6.1.4.1.164.3.1.6.7.7.1.5	Counter32	read-only	Number of frames that were transmitted due to time interval elapse. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing time interval elapses. The packetizing time interval is the interval in msec that it takes to build a Max. size frame.
C32 ip2IfStatTxSignaling	1.3.6.1.4.1.164.3.1.6.7.7.1.10	Counter32	read-only	Number of signaling frames that were transmitted.
C32 ip2IfStatTxVoice	1.3.6.1.4.1.164.3.1.6.7.7.1.11	Counter32	read-only	Number of voice frames that were transmitted.
INT ip2IfSuperTandem	1.3.6.1.4.1.164.3.1.6.7.1.1.36	INTEGER	read-create	The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem allows transmission of compressed voice between a few Vmux 2100 hubs, and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay.
OCT ip2IfSuperTandemBitMask	1.3.6.1.4.1.164.3.1.6.7.1.1.86	OCTET STRING	read-create	This MIB object enables controlling the Time Slot/Channel rate. Valid values: 1 - FF HEX Each BIT represents 1/8 of the TS. Example: 7E (0111 1110) means that 6/8 of the TS (the center ones) are masked and data will be Tx/Rx only through them. This MIB object is relevant only when Super Tandem is enabled.
ip2IfTable	1.3.6.1.4.1.164.3.1.6.7.1		not-accessible	Channels Configuration Table.
IP ip2IfTdmBackUpNextHop	1.3.6.1.4.1.164.3.1.6.7.1.1.30	IpAddress	read-create	Defines the TDM bundle default router in case there was a switch from the Primary Link (for example an ETH port) to a TDM backup Link like E1, T1 or Serial Link. This parameter is relevant only when a Backup Link is configured. When a Backup Link is not configured the value will be: 0.0.0.0
I32 ip2IfTDMBytesInFrame	1.3.6.1.4.1.164.3.1.6.7.1.1.11	Integer32	read-create	The number of TDM bytes to be placed in a single IP frame payload. For ip2IfTDMoIpMode = cesOverPsn this parameter indicates the number of IP frames, calculated as: 1440/.
I32 ip2IfTDMFrameBytes	1.3.6.1.4.1.164.3.1.6.7.2	Integer32	read-write	The number of TDM bytes to be placed in a single IP frame payload.
INT ip2IfTDMoIpMode	1.3.6.1.4.1.164.3.1.6.7.1.1.20	INTEGER	read-create	The TDMoIP Mode configuration. Static- means TS can Tx any time. dynamicLES - means TS can Tx only when line is enabled according to LES protocol. dynamicCAS - means TS can Tx only when line is enabled according to CAS protocol. cesOverIp - use for information that this bundle is used for CES Over IP. voiceOverMpls - Voice over Multi Protocol Label Switching. hdlc - High Level Data Link. voIpComprHeader - indicates proprietary compressed IP header packets. voMplsComprHeader - indicates proprietary compressed MPLS header packets.
I32 ip2IfTimeElapsed	1.3.6.1.4.1.164.3.1.6.7.1.1.21	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
I32 ip2IfToneAckInterval	1.3.6.1.4.1.164.3.1.6.7.1.1.54	Integer32	read-create	Time Interval in milli seconds from the time a Vmux sends tone/s to a local PBX until it receives an acknowledgement from this PBX. Valid values: 60...400 in steps of 20.
I32 ip2IfTos	1.3.6.1.4.1.164.3.1.6.7.1.1.10	Integer32	read-create	The TOS (Type of Service) value: 0..255. In Vmux-2100/110 devices versions 3.1 and up, in Vmux-210 and in Vmux-4x0: LSB 8 bits - 00 00 00 XX will be used for Signaling packets TOS. Next 8 bits - 00 00 XX 00 will be used for Media packets TOS. Next 16 bits - will be 0. XX = Hex values: 0..FF For mixed packets, TOS of Media Packets will be used. Signaling packets are for example: Keep alive packets and ABCD signaling bits. Media packets are for example: voice, fax, HDLC, payload packets.
I32 ip2IfTosValue	1.3.6.1.4.1.164.3.1.6.7.3	Integer32	read-write	The TOS value to write in the IP frame.
I32 ip2IfTxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.35	Integer32	read-create	Transmit gain in dBm.
INT ip2IfUdpMuxMethod	1.3.6.1.4.1.164.3.1.6.7.1.1.90	INTEGER	read-create	This parameter determines according to which field the multiplexing is made: srcPort (2) - multiplexing according to the UDP Source Port (Dest=0x085e). This should be the default value, for backwards compatibility. destPort (3) - multiplexing according to the UDP Destination Port (standard multiplexing). The UDP Source and Destination ports' range is determined according to ip2IfUdpMuxMethod value: For srcPort (2) the range is 1-7000 For destPort (3) the range is 49152-65535.
INT ip2IfV23HD	1.3.6.1.4.1.164.3.1.6.7.1.1.83	INTEGER	read-create	This parameter shows whether V.23 Half Duplex Modem Protocol is enabled on the bundle.
INT ip2IfVadMethod	1.3.6.1.4.1.164.3.1.6.7.1.1.70	INTEGER	read-create	Voice Activity Detection (VAD) method. proprietary (2) - non standard VAD based only on power measurement. It is very sensitive to background noise. internalITUT (3) - standard ITU-T VAD. It is a robust method.
I32 ip2IfValidIntervals	1.3.6.1.4.1.164.3.1.6.7.1.1.22	Integer32	read-only	The number of previous intervals for which data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute intervals since the interface has been online.
INT ip2IfVbdRate	1.3.6.1.4.1.164.3.1.6.7.1.1.74	INTEGER	read-create	Voice Band Data (VBD) rate for this bundle.
U32 ip2IfVbdSwitchbackTime	1.3.6.1.4.1.164.3.1.6.7.1.1.87	Unsigned32	read-create	Time in msec required for the DSP to switch back from VBD (Voice Band Data) to Voice. For Vmux: the values will be in steps of 30 msec.
I32 ip2IfVlanFramePriority	1.3.6.1.4.1.164.3.1.6.7.1.1.14	Integer32	read-create	VLAN Frame priority.
I32 ip2IfVlanID	1.3.6.1.4.1.164.3.1.6.7.5	Integer32	read-write	VLAN ID.
I32 ip2IfVlanIdentifier	1.3.6.1.4.1.164.3.1.6.7.1.1.13	Integer32	read-create	VLAN ID.
I32 ip2IfVlanPriority	1.3.6.1.4.1.164.3.1.6.7.6	Integer32	read-write	Frame priority.
INT ip2IfVlanSupport	1.3.6.1.4.1.164.3.1.6.7.1.1.12	INTEGER	read-create	VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
INT ip2IfVlanTagging	1.3.6.1.4.1.164.3.1.6.7.4	INTEGER	read-write	VLAN support. no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
OCT ip2IfVoiceOos	1.3.6.1.4.1.164.3.1.6.7.1.1.16	OCTET STRING	read-create	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
INT ip2IfWap	1.3.6.1.4.1.164.3.1.6.7.1.1.92	INTEGER	read-create	Enable/Disable WAP (Wireless Application Protocol) for this bundle. WAP allows users to access the internet from wireless devices.
lag	1.3.6.1.4.1.164.6.2.54
U32 lagCnfgIdx	1.3.6.1.4.1.164.6.2.54.1.1.1	Unsigned32	not-accessible	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
INT lagDistributionMethod	1.3.6.1.4.1.164.6.2.54.1.1.4	INTEGER	read-create	This object defines the criteria for the 802.3ad (LAG) to split the traffic between ports
lagEntry	1.3.6.1.4.1.164.6.2.54.1.1		not-accessible	An entry in the LAG table.
U32 lagIdx	1.3.6.1.4.1.164.6.2.54.1.1.2	Unsigned32	not-accessible	This object indicates LAG unique index.
INT lagLacpEnable	1.3.6.1.4.1.164.6.2.54.1.1.10	INTEGER	read-create	Enabling/Disabling the LACP for a LAG. The LACP will be enabled for all ports belonging to this LAG.
POR lagPortMembers	1.3.6.1.4.1.164.6.2.54.1.1.3	PortList	read-create	The set of ports which are permanently assigned to the Link Aggregation Group. The default value of this object is a string of zeros.
INT lagRdnMethod	1.3.6.1.4.1.164.6.2.54.1.1.9	INTEGER	read-create	This object defines the redundancy method.
INT lagRecoveryMode	1.3.6.1.4.1.164.6.2.54.1.1.5	INTEGER	read-create	This object defines whether traffic will be returned to a port after its recovery. This object is applicable only when lagDistributionMethod= oneToOne (3).
ROW lagRowStatus	1.3.6.1.4.1.164.6.2.54.1.1.7	RowStatus	read-create	This object enables user to create/delete entries of this table. Note: When using LAG standard package, this table is static, hence, only the values active(1), notInService(2) are used.
U32 lagShutDownDurationUponFlip	1.3.6.1.4.1.164.6.2.54.1.1.8	Unsigned32	read-create	This object defines the duration (in seconds) the active port transmission is shut down after LAG Flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0=no shut-down. This object is applicable only when lagDistributionMethod=oneToOne(3) and mainly when each of the Links of our device is connected to a different device.
U32 lagStatActivePort	1.3.6.1.4.1.164.6.2.54.2.1.2	Unsigned32	read-only	This object indicates the current active port. It is applicable only when lagDistributionMethod = oneToOne. The value is the ifIndex of the port. 0 = none of the ports is active.
lagStatEntry	1.3.6.1.4.1.164.6.2.54.2.1		not-accessible	An entry in the LAG Status table.
U32 lagStatForcePort	1.3.6.1.4.1.164.6.2.54.2.1.1	Unsigned32	read-write	This object enables user to enforce the active port. 0 = No Enforcement; Otherwise the ifIndex of the port.
lagStatTable	1.3.6.1.4.1.164.6.2.54.2		not-accessible	A table defining Link Aggregation Groups Redundancy. This table is applicable only when lagDistributionMethod = oneToOne.
lagTable	1.3.6.1.4.1.164.6.2.54.1		not-accessible	A table defining Link Aggregation Groups port association, and other parameters.
U32 lagWaitToRestore	1.3.6.1.4.1.164.6.2.54.1.1.6	Unsigned32	read-create	This object defines traffic recovery time (in seconds) to the port after its recovery. This object is applicable only when lagRecoveryMode= revertive (3).
NTF licenseUpdateTrap	1.3.6.1.4.1.164.6.1.0.27			This trap is sent whenever a license is successfully downloaded or whenever a license's demo duration is expired.
linkSelectorCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.17.2.1		not-accessible	An entry in table.
I32 linkSelectorCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
linkSelectorCnfgTable	1.3.6.1.4.1.164.3.2.3.2.17.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
I32 linkSelectorMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.17.2.1.4	Integer32	read-write	Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=move immediately to higher prioritized connected link. UNIT is seconds.
I32 linkSelectorMinBUSession	1.3.6.1.4.1.164.3.2.3.2.17.2.1.7	Integer32	read-write	Minimum duration of a backup session before returning to Main Link. Relevant in Backup Mode and when Revert is auto(2). Value 255 is for NEVER which means never return to Main Link. UNIT is minutes.
INT linkSelectorMode	1.3.6.1.4.1.164.3.2.3.2.17.2.1.5	INTEGER	read-write	If the link selector is in mode: backup(2)=then the link with the lower priority will be used in case of failure of the higher priority link, bod(3)=bandwidth on demand or dynamic bandwidth allocation means that links with lower priority will be used whenever additional bandwidth is required.
linkSelectorPLinkEntry	1.3.6.1.4.1.164.3.2.3.2.17.3.1		not-accessible	An entry in table.
linkSelectorPLinkTable	1.3.6.1.4.1.164.3.2.3.2.17.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
I32 linkSelectorPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be internal port number: higher or equal to linkSeL1(201).
INT linkSelectorRevert	1.3.6.1.4.1.164.3.2.3.2.17.2.1.6	INTEGER	read-write	If the link selector is in mode backup: auto(2)=return automatically to Main link when it is OK. manual(3)=stays connected to backup link.
INT linkSelectorSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.2	INTEGER	read-only	Slot Index
NTF localConnStatusTrap	1.3.6.1.4.1.164.6.1.3.0.13			This trap is sent upon a change in Local connectivity of Bundle connection.
mapLinkEntry	1.3.6.1.4.1.164.3.3.4.2.1		not-accessible	An entry in table.
I32 mapLinkId	1.3.6.1.4.1.164.3.1.5.1.1.1	Integer32	read-only	A unique identifier of the link
I32 mapLinkIdx	1.3.6.1.4.1.164.3.3.4.2.1.1	Integer32	read-only	A unique identifier of the link
I32 mapLinkPortIdx	1.3.6.1.4.1.164.3.3.4.2.1.3	Integer32	read-write	This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT mapLinkPrtIdx	1.3.6.1.4.1.164.3.1.5.1.1.3	INTEGER	read-write	This attribute indicates a unique port number.
INT mapLinkSlotIdx	1.3.6.1.4.1.164.3.3.4.2.1.2	INTEGER	read-write	This attribute indicates a unique slot position where the module is inserted.
INT mapLinkSltIdx	1.3.6.1.4.1.164.3.1.5.1.1.2	INTEGER	read-write	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries clA(3), io6(10)..io12(16) are not valid.
INT mapLinkState	1.3.6.1.4.1.164.3.3.4.2.1.4	INTEGER	read-only	This attribute indicates the status of the link between the two muxes
INT mapLinkStatus	1.3.6.1.4.1.164.3.1.5.1.1.4	INTEGER	read-only	This attribute indicates the status of the link between the two muxes
mapLinkTable	1.3.6.1.4.1.164.3.3.4.2		not-accessible	A table.
mappingProfileObjects	1.3.6.1.4.1.164.6.3.9
mapWanGen	1.3.6.1.4.1.164.3.1.5
markingProfileEntry	1.3.6.1.4.1.164.6.3.12.1		not-accessible	A conceptual row where each row contains one Marking attribute.
U32 markingProfileIndex	1.3.6.1.4.1.164.6.3.12.1.1	Unsigned32	not-accessible	Defines the Marking Profile ID.
INT markingProfileMethod	1.3.6.1.4.1.164.6.3.12.1.5	INTEGER	read-create	This attribute defines the method upon which marking is done.
STR markingProfileName	1.3.6.1.4.1.164.6.3.12.1.3	SnmpAdminString	read-create	This attribute defines the unique name assigned to the Marking profile.
ROW markingProfileRowStatus	1.3.6.1.4.1.164.6.3.12.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
markingProfileTable	1.3.6.1.4.1.164.6.3.12		not-accessible	Marking profile table. Each profile holds a marking function which converts CoS values to Service Provider priority values.
OCT markingSpVlanPBit	1.3.6.1.4.1.164.6.3.12.1.4	OCTET STRING	read-create	For ETX-202A : This attribute defines the value of the SP VLAN P-Bit that is assigned for each CoS: Octet 0 corresponds to CoS = 0 Octet 1 corresponds to CoS = 1 ... Octet 7 corresponds to CoS = 7. For LA-210 from V1.5 : This attribute defines the value of the SP VLAN P-Bit that is assigned for each frame according to the value of markingProfileMethod parameter : Octet 0 corresponds to value 0 of 802.1 P-bit/DSCP/TOS. Octet 1 corresponds to value 1 of 802.1 P-bit/DSCP/TOS. ... Octet 7 corresponds to value 7 of 802.1 P-bit/DSCP/TOS. Octets 8-63 correspond to DSCP values 8-63.
I32 maskingCurrentEntries	1.3.6.1.4.1.164.4.1.6.2	Integer32	read-only	The number of entries in the mask table.
ADR maskingDestActiveBits	1.3.6.1.4.1.164.4.1.6.3.1.13	GenAddress	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the positions of the wild card characters (*) in the maskingDestAddress field. Only the 1's bit will be taken in considerations.
ADR maskingDestAddress	1.3.6.1.4.1.164.4.1.6.3.1.12	GenAddress	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. The destination address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket. In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles). The IPX socket entered here has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care.
INT maskingDestCondition	1.3.6.1.4.1.164.4.1.6.3.1.15	INTEGER	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that matches the content of maskingDestAddress. false - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that does not match the content of maskingDestAddress.
INT maskingDestMacOrNet	1.3.6.1.4.1.164.4.1.6.3.1.14	INTEGER	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingDestMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingDestMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingDestMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingDestMacOrNet can be either macAddress or appleAddress. The variable maskingDestAddress and maskingDestActiveBits will be treated as MAC, or NET address.
maskingEntry	1.3.6.1.4.1.164.4.1.6.3.1		not-accessible	Defines the contents of each line in the mask table.
INT maskingFrameType	1.3.6.1.4.1.164.4.1.6.3.1.6	INTEGER	read-write	Enables the user to decide about frame type * all frame * just broadcast * just multicast.
INT maskingFrameTypeCondition	1.3.6.1.4.1.164.4.1.6.3.1.7	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingFrameType the packet contains data that matches the content of maskingFrameType. fa lse - Condition is valid if at the position specified by maskingFrameType the packet contains data that does not match the content of maskingFrameType.
I32 maskingHighLevelProt	1.3.6.1.4.1.164.4.1.6.3.1.18	Integer32	read-write	This field is set in connection to the maskingProtocolType variable. This variable specifies the high level protocols (application). As for today it supports just IP protocol stack. The object's value is a sum of the following instances values (selected by user): none (0), -- don't care ftp (1), ftpC (2), telnet (4), smtp (8), tftp (16), snmp (32), snmpTrap (64), ipRip (128), www (256), email (512), dns (1024), For Apple Protocol only: rtmp (2048), nbp (4096), atp (8192), aep (16384), zip (32768), adsp (65536), pap (131072), asp (262144) Example: if ftp(1), snmp(32) and snmpTrap(64) instances were selected, the value should be 97 (=1+32+64).
INT maskingHighLevelProtCondition	1.3.6.1.4.1.164.4.1.6.3.1.19	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that matches the content of maskingHighLevelProt. false - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that does not match the content of maskingHighLevelProt.
I32 maskingIfIndex	1.3.6.1.4.1.164.4.1.6.3.1.2	Integer32	read-only	Specifies the ifIndex of the interface to which the mask is applied.
I32 maskingIndex	1.3.6.1.4.1.164.4.1.6.3.1.3	Integer32	read-only	An index to the masking table. This number should not be greater than maskingMaxEntries
INT maskingLowLevelProt	1.3.6.1.4.1.164.4.1.6.3.1.16	INTEGER	read-write	This field is set in conjunction with the maskingProtocolType variable. This variable specifies the low level protocol. The IPX socket entered in maskingDestAddress has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care.
INT maskingLowLevelProtCondition	1.3.6.1.4.1.164.4.1.6.3.1.17	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that matches the content of maskingLowLevelProt. false - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that does not match the content of maskingLowLevelProt.
I32 maskingMaxEntries	1.3.6.1.4.1.164.4.1.6.1	Integer32	read-only	The maximum number of entries in the masking table.
INT maskingOperation	1.3.6.1.4.1.164.4.1.6.3.1.22	INTEGER	read-write	The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list. smartMask = the operation and destination of the mask will be determined by the objects of the Smart Table (old masking table: radBridgeMaskTable). If maskingType is codConnect, the 'block' value is NOT allowed. If maskingType is codDisconnect, the 'forward' value is NOT allowed.
I32 maskingPortNum	1.3.6.1.4.1.164.4.1.6.3.1.20	Integer32	read-write	The port number is the same as in high level protocol. It specifies the dest. port in IP case or the dest. socket in case of IPX & apple protocols. IP - This object is applicable only if none (0) value was selected in maskingHighLevelProt. IPX - This object is applicable only if the socket entered in maskingDestAddress is 'don't care'(00) AND maskingLowLevelProt is NOT ipxRip or ipxSap. Apple - This option is applicable only if the socket entered in maskingDestAddress is 'don't care'(00).
INT maskingPortNumCondition	1.3.6.1.4.1.164.4.1.6.3.1.21	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingPortNum the packet contains data that matches the content of maskingPortNum. false - Condition is valid if at the position specified by maskingPortNum the packet contains data that does not match the content of maskingPortNum. This object is applicable only when maskingPortNum is applicable.
INT maskingProtocolType	1.3.6.1.4.1.164.4.1.6.3.1.4	INTEGER	read-write	The base protocol for masking. IPX, IP, others.
OID maskingSmartMaskOID	1.3.6.1.4.1.164.4.1.6.3.1.5	OBJECT IDENTIFIER	read-only	A reference to a specific Smart mask table (old radBridgeMaskTable) which enables a more specific mask type. If this information is not available, its value should be set to the OBJECT IDENTIFIER { 0 0 }.
ADR maskingSourceActiveBits	1.3.6.1.4.1.164.4.1.6.3.1.9	GenAddress	read-write	Specifies the positions of the wild card characters (*) in the maskingSourceAddress field. Only the 1's bit will be taken in considerations.
ADR maskingSourceAddress	1.3.6.1.4.1.164.4.1.6.3.1.8	GenAddress	read-write	The source address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles).
INT maskingSourceCondition	1.3.6.1.4.1.164.4.1.6.3.1.11	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that matches the content of maskingSourceAddress. false - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that does not match the content of maskingSourceAddress.
INT maskingSourceMacOrNet	1.3.6.1.4.1.164.4.1.6.3.1.10	INTEGER	read-write	The variable maskingSourceAddress and maskingSourceActiveBits will be treated as MAC, or NET address. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingSourceMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingSourceMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingSourceMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingSourceMacOrNet can be either macAddress or appleAddress.
I32 maskingSrcPortNum	1.3.6.1.4.1.164.4.1.6.3.1.23	Integer32	read-write	The source port number. For IP: No Condition. For IPX: This object is applicable only if the socket entered in maskingSourceAddress is don't care (00) and maskingLowLevelProt is NOT ipxRip or ipxSap. For Apple:This object is applicable only if the socket entered in maskingSourceAddress is don't care (00).
INT maskingSrcPortNumCondition	1.3.6.1.4.1.164.4.1.6.3.1.24	INTEGER	read-write	The same as 'maskingPortNumCondition'. Relates to source port.
maskingTable	1.3.6.1.4.1.164.4.1.6.3		not-accessible	This is the new masking scheme. Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement and an action defined by maskingOperation.
INT maskingType	1.3.6.1.4.1.164.4.1.6.3.1.1	INTEGER	read-only	Defines the type of mask entry.
I32 mdlAlarmCounter	1.3.6.1.4.1.164.3.3.2.1.3.1.1.8	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
INT mdlAlarmInvert	1.3.6.1.4.1.164.3.3.2.1.3.1.1.6	INTEGER	read-only	Alarm Invert is : on/off.
INT mdlAlarmMask	1.3.6.1.4.1.164.3.3.2.1.3.1.1.5	INTEGER	read-only	Alarm Mask is : on/off.
INT mdlAlarmOnOff	1.3.6.1.4.1.164.3.3.2.1.3.1.1.7	INTEGER	read-only	Alarm state is : on/off.
I32 mdlAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.3.3.2.1.3	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
I32 mdlAlarmsCmprAlarmSlot	1.3.6.1.4.1.164.3.1.3.3.2.1.2	Integer32	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid.
mdlAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.3.3.2.1		not-accessible	An entry in table.
OCT mdlAlarmsCmprObj	1.3.6.1.4.1.164.3.1.3.3.2.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
mdlAlarmsCmprTable	1.3.6.1.4.1.164.3.1.3.3.2		not-accessible	A table.
I32 mdlAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.3.3.2.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
mdlAlr	1.3.6.1.4.1.164.3.3.2.1.3
I32 mdlAlrCode	1.3.6.1.4.1.164.3.3.2.1.3.1.1.3	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
mdlAlrEntry	1.3.6.1.4.1.164.3.3.2.1.3.1.1		not-accessible	An entry in table.
I32 mdlAlrIdx	1.3.6.1.4.1.164.3.3.2.1.3.1.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive
OCT mdlAlrMask	1.3.6.1.4.1.164.3.3.2.1.3.2.1.2	OCTET STRING	read-write	This object is a mask that indicates which card level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the card level will be 0. This object is applicable only when mdlSAlrMaskAll=off (otherwise all card alarms are masked). Example: When Alarm having the code 8 is masked, the value of this object will be 100 (hex).
mdlAlrMaskEntry	1.3.6.1.4.1.164.3.3.2.1.3.2.1		not-accessible	An entry in table.
INT mdlAlrMaskSltIdx	1.3.6.1.4.1.164.3.3.2.1.3.2.1.1	INTEGER	read-only	This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.
mdlAlrMaskTable	1.3.6.1.4.1.164.3.3.2.1.3.2		not-accessible	The list of card masked alarms.
INT mdlAlrSltIdx	1.3.6.1.4.1.164.3.3.2.1.3.1.1.2	INTEGER	read-only	This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.
INT mdlAlrState	1.3.6.1.4.1.164.3.3.2.1.3.1.1.4	INTEGER	read-only	This object indicates the card alarm severity.
mdlAlrTable	1.3.6.1.4.1.164.3.3.2.1.3.1		not-accessible	The list of card alarms.
I32 mdlCCnfgIdx	1.3.6.1.4.1.164.3.1.3.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..100) being referred. Value 255 specifies the TmpCnfg
I32 mdlCConfigIdx	1.3.6.1.4.1.164.3.3.2.1.2.1.1	Integer32	read-only	This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch).
INT mdlCDhcpClientEnable	1.3.6.1.4.1.164.3.1.3.2.1.1.7	INTEGER	read-write	Enable/Disable the feature of DHCP Client for the selected card.
mdlCEntry	1.3.6.1.4.1.164.3.3.2.1.2.1		not-accessible	An entry in table.
OCT mdlCInterfaces	1.3.6.1.4.1.164.3.1.3.2.1.1.9	OCTET STRING	read-only	Octet string which indicates 'present' interfaces in card. Each '0' bit stands for non-present interface. Each '1' bit stands for present interface. For ASMi54C card of LRS-102 and MP-4100 notPresent interfaces may be: - SHDSL Line ID with no wire pairs assigned to it (does not exist in ifTable) - PCS without SHDSL Line binded to it, (exist in ifTable, with ifOperStatus= notPresent) - External DS1 when its LIU is used by an Internal DS1 of the same card - Internal DS1 when single bearer is not TDM. In each octet, MS bit represents port 1 and LS bit represents port 8 MSB LSB 1 0 0 0 1 0 0 0 -- Example: Port # 1 and 5 are present. Port 1 2 3 4 5 6 7 8 1st Octet (MSB octet) represents SDHSL Lines 2nd Octet represents PCS 3rd Octet represents External DS1 4th Octet represents Internal DS1 5th and 6th Octets are reserved for future Internal DS1. For OP-108/106 cards of LRS-102 and MP-4100 notPresent interfaces may be: - External DS1 when its 'associated' Int-DS1 port is connected to another card - Internal DS1 when its 'associated' Ext-DS1 port is connected to another card (Both may be 'present' when inter-connected). 1st Octet represents External DS1 2nd Octet represents Internal DS1 Bit representation, same as for ASMi-54C card.
mdlCl	1.3.6.1.4.1.164.3.3.2.2
mdlClEntry	1.3.6.1.4.1.164.3.3.2.2.1.1		not-accessible	An entry in table.
INT mdlClIdx	1.3.6.1.4.1.164.3.3.2.2.1.1.1	INTEGER	read-only	This object indicates the Cl slot referred.
STR mdlClLastFlipCause	1.3.6.1.4.1.164.3.3.2.2.1.1.5	DisplayString	read-only	The cause of last flip.
STR mdlClLastFlipDate	1.3.6.1.4.1.164.3.3.2.2.1.1.3	DisplayString	read-only	Date when last flip occured. The format would be as specified by the sysSDateFormat.
STR mdlClLastFlipTime	1.3.6.1.4.1.164.3.3.2.2.1.1.4	DisplayString	read-only	Time when last flip occured.
I32 mdlClSwchStatus	1.3.6.1.4.1.164.3.3.2.2.1.1.2	Integer32	read-only	This object indicates the status of the switches on the referred DCL card. Each switch is represented by a bit. The status is a sum of 2n, according to the bits. There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (21 + 2**0). When the status of the switches is unknown, the value of this object will be 255.
mdlClTable	1.3.6.1.4.1.164.3.3.2.2.1		not-accessible	A table.
I32 mdlCmprCnfgIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
mdlCmprEntry	1.3.6.1.4.1.164.3.1.3.3.1.1		not-accessible	An entry in table.
OCT mdlCmprObj	1.3.6.1.4.1.164.3.1.3.3.1.1.5	OCTET STRING	read-write	This attribute is the compressed information itself.
INT mdlCmprSltIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
mdlCmprTable	1.3.6.1.4.1.164.3.1.3.3.1		not-accessible	A table.
I32 mdlCmprTypIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 mdlCmprVersion	1.3.6.1.4.1.164.3.1.3.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 mdlCNoOfExternPrt	1.3.6.1.4.1.164.3.1.3.2.1.1.4	Integer32	read-only	Number of external ports in the programmed card of the specific slot position
I32 mdlCNoOfExtPrt	1.3.6.1.4.1.164.3.3.2.1.2.1.4	Integer32	read-only	Number of external ports in the programmed module of the specific slot position
I32 mdlCNoOfInternPrt	1.3.6.1.4.1.164.3.1.3.2.1.1.5	Integer32	read-only	Number of internal ports in the programmed card of the specific slot position.
I32 mdlCNoOfIntPrt	1.3.6.1.4.1.164.3.3.2.1.2.1.5	Integer32	read-only	Number of internal ports in the programmed module of the specific slot position.
NTF mdlConnectTrap	1.3.6.1.4.1.164.3.3.0.3			This trap is sent when a card is removed.
I32 mdlCParam	1.3.6.1.4.1.164.3.3.2.1.2.1.6	Integer32	read-write	General configuration object at card level (per configuration). NotApplicable=0, for cards that don't support this object. For D8U and D16U cards of DXC, the object will indicate the port on which BERT will be performed. The port can be one of the external ports, any of its associated B1, B2, D ports or no port of the card (None=0). For port indexes see DXC R6 spec. For Gmux-2000, this parameter used for determining the Gigabit ETH exit port
INT mdlCPrgCardType	1.3.6.1.4.1.164.3.1.3.2.1.1.3	INTEGER	read-write	This attribute indicates the type of card assigned to the specific slot in the common configuration. This object is identical in all the configurations (1..100). Only the TmpCnf(255) may have different value. The write operation is valid only to the TmpCnfg entry.
mdlCPrgEntry	1.3.6.1.4.1.164.3.1.3.2.1.1		not-accessible	An entry in table.
mdlCPrgTable	1.3.6.1.4.1.164.3.1.3.2.1		not-accessible	A table.
INT mdlCProgCardType	1.3.6.1.4.1.164.3.3.2.1.2.1.3	INTEGER	read-write	This object indicates the card type assigned to the specific slot in the common configuration. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. The write operation is valid only for the TmpCnfg entry.
INT mdlCRdnExists	1.3.6.1.4.1.164.3.1.3.2.1.1.8	INTEGER	read-only	This object indicates whether any port of the programmed card is configured to be part of a Redundancy/APS pair. If at least one port of the programmed card is configured to be part of a Redundancy/APS pair, the value will be 'yes'. Otherwise, it will be 'no'.
INT mdlCSlotIdx	1.3.6.1.4.1.164.3.3.2.1.2.1.2	INTEGER	read-only	This object indicates a unique number of the slot position in which the module is inserted. The Kilomux should use enumerated values starting with kmx.
INT mdlCSltIdx	1.3.6.1.4.1.164.3.1.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
mdlCTable	1.3.6.1.4.1.164.3.3.2.1.2		not-accessible	A table.
INT mdlCWorkMode	1.3.6.1.4.1.164.3.1.3.2.1.1.6	INTEGER	read-write	Working mode of the card. The user may configure the card to work in a stand alone mode or integrated with the device. Example for use in MHS-IP cards: - standAlone - in this mode, the router works so that data is received via the LAN (Eth) port and is transmitted via the WAN (HS) external port without going through the MPH device. - integrated - in this mode, the router works so that it is integrated in the MPH and routes DLCIs into the device.
mdlDacsMux	1.3.6.1.4.1.164.3.3.2
mdlGen	1.3.6.1.4.1.164.3.3.2.1
mdlMux	1.3.6.1.4.1.164.3.2.2
I32 mdlPbxFraCnfgIdx	1.3.6.1.4.1.164.3.2.2.1.1.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT mdlPbxFraEnhEcho	1.3.6.1.4.1.164.3.2.2.1.1.1.1.3	INTEGER	read-write	Refers to external ports of an analogue module and to the internal ports of the other mvc4 types of modules. ms16(3) means that the four voice ports have enhanced echo of 16ms. ms32(4) means that the two first ports have enhanced echo of 32 ms while the last two ports have no enhanced echo.
INT mdlPbxFraFramerSlot	1.3.6.1.4.1.164.3.2.2.1.1.1.1.8	INTEGER	read-write	Slot where is sitting the Framer.
mdlPbxFramerCnfg	1.3.6.1.4.1.164.3.2.2.1.1
mdlPbxFramerCnfgEntry	1.3.6.1.4.1.164.3.2.2.1.1.1.1		not-accessible	An entry in table.
mdlPbxFramerCnfgTable	1.3.6.1.4.1.164.3.2.2.1.1.1		not-accessible	This table contains parameters relevant to a module belonging to a digital voice system, except mdlPbxFraEnhEcho which is relevant also for analog cards.
INT mdlPbxFraSignaling	1.3.6.1.4.1.164.3.2.2.1.1.1.1.9	INTEGER	read-write	Signaling - describes the way the signaling ABCD bits pass from the local extension to the remote extension and vice-versa. endToEnd = the signaling ABCD bits pass without change from local to remote extension. localTermination = the signaling ABCD bits received from the local extension are translated to different ON Hook/OFF Hook bit values and then passed to remote extension. This is relevant when the Local and Remote ON Hook/OFF Hook values are different.
OCT mdlPbxFraSignalMask	1.3.6.1.4.1.164.3.2.2.1.1.1.1.7	OCTET STRING	read-write	In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the 'don't care' A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote.
INT mdlPbxFraSignalMode	1.3.6.1.4.1.164.3.2.2.1.1.1.1.5	INTEGER	read-write	Refers to the signaling mode of the Framer module. tieTrunk(2), tieInvert(3), casTrans(4) are standard coding of the signaling protocol. casTrans(4) is Channel Associated Signaling (the signaling is within the channels time slot). ccsTrans(6) is Transparent Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). userDefined(5) allows the user to define the signaling protocol he wants. In this case, the next two MIB fields are relevant.
OCT mdlPbxFraSignalVector	1.3.6.1.4.1.164.3.2.2.1.1.1.1.6	OCTET STRING	read-write	In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote In conjunction with the Mask, mdlPbxFraSignalMask, it is possible to compute the signal mode.
INT mdlPbxFraSltIdx	1.3.6.1.4.1.164.3.2.2.1.1.1.1.2	INTEGER	read-only	The slot relevant to this module.
I32 mdlPbxFraTransSigTs	1.3.6.1.4.1.164.3.2.2.1.1.1.1.10	Integer32	read-write	This is the Time Slot that is used for Transparent CCS signaling. The values of this TS are 1-24 for T1 & 1-31 for E1. The default for E1 is 16 & for T1 it is 24. If no signaling is used then the TS should be 255 (None).
INT mdlPbxFraTSGroupAss	1.3.6.1.4.1.164.3.2.2.1.1.1.1.4	INTEGER	read-write	In case of T1 modules: group1=(1,2,3,4), ...., group6=(21,22,23,24) while in case of E1 modules: - If prtExPh1MlLineType=g732sE1 or g732sE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,17), group5=(18,19,20,21),...,group7=(26,27,28,29) group8=(30,31). - If prtExPh1MlLineType=g732nE1 or g732nE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,16), group5=(17,18,19,20),...,group7=(25,26,27,28) group8=(29,30,31).
IP mdlProtIpAddress	1.3.6.1.4.1.164.3.2.2.1.2.1.3	IpAddress	read-only	A Protected IP address.
I32 mdlProtIpCnfgIdx	1.3.6.1.4.1.164.3.2.2.1.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being accessed. Idx 255 relates to the TmpCnfg. For Agents having several configuration, Write operation is allowed only to the Temporary Configuration.
mdlProtIpEntry	1.3.6.1.4.1.164.3.2.2.1.2.1		not-accessible	An entry in table.
ROW mdlProtIpRowStatus	1.3.6.1.4.1.164.3.2.2.1.2.1.4	RowStatus	read-create	This parameter allows creating/deleting entries of this table.
INT mdlProtIpSlotIdx	1.3.6.1.4.1.164.3.2.2.1.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the 2104 Unit the entries io6(10)..io16) are not valid.
mdlProtIpTable	1.3.6.1.4.1.164.3.2.2.1.2		not-accessible	This table contains Protected IP Addresses for ML-IP cards when working in IP Ring Mode.
mdlPs	1.3.6.1.4.1.164.3.3.2.3
mdlPsEntry	1.3.6.1.4.1.164.3.3.2.3.1.1		not-accessible	An entry in table.
INT mdlPsIdx	1.3.6.1.4.1.164.3.3.2.3.1.1.1	INTEGER	read-only	This object indicates the PS card referred.
INT mdlPsStatus	1.3.6.1.4.1.164.3.3.2.3.1.1.2	INTEGER	read-only	This object indicates the status of the PS card.
mdlPsTable	1.3.6.1.4.1.164.3.3.2.3.1		not-accessible	A table.
INT mdlPsTestResult	1.3.6.1.4.1.164.3.3.2.3.1.1.3	INTEGER	read-only	This object indicates the result of the PS card test. ok (1) - the test passed successfully. f12V (2) - 12V FAIL was detected f5V (3) - 5V FAIL was detected.
INT mdlSActivity	1.3.6.1.4.1.164.3.3.2.1.1.1.9	INTEGER	read-only	notApplicable - when the slot is empty (no module) offline(1) - when the module is not active (redundant) online (2) - when the module is active .
INT mdlSAlarmStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.5	INTEGER	read-only	Indicates the current alarm state only for card level. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT mdlSAlarmStatusAll	1.3.6.1.4.1.164.3.3.2.1.1.1.6	INTEGER	read-only	Indicates the current card alarm state including the lower level: card, port. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT mdlSAlrClearAllCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.11	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on card and port level alarms . Upon completion, the value will automatically change to off(2).
INT mdlSAlrClearCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.10	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the card level alarms . Upon completion, the value will automatically change to off(2).
I32 mdlSAlrCode	1.3.6.1.4.1.164.3.1.3.1.2.1.4	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at card level.
STR mdlSAlrCodeDescription	1.3.6.1.4.1.164.3.1.3.1.2.1.3	DisplayString	read-only	This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
I32 mdlSAlrCounter	1.3.6.1.4.1.164.3.1.3.1.2.1.7	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
mdlSAlrEntry	1.3.6.1.4.1.164.3.1.3.1.2.1		not-accessible	An entry in table.
I32 mdlSAlrIdx	1.3.6.1.4.1.164.3.1.3.1.2.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive.
INT mdlSAlrInvert	1.3.6.1.4.1.164.3.1.3.1.2.1.9	INTEGER	read-only	Alarm invert : on/off.
INT mdlSAlrMask	1.3.6.1.4.1.164.3.1.3.1.2.1.8	INTEGER	read-only	Alarm mask : on/off.
INT mdlSAlrMaskAll	1.3.6.1.4.1.164.3.3.2.1.1.1.12	INTEGER	read-write	on(3) - will cause masking of all the card level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all card level alarms except those masked via the mdlAlrMaskTable.
INT mdlSAlrSeverity	1.3.6.1.4.1.164.3.1.3.1.2.1.5	INTEGER	read-only	The severity of the alarm.
INT mdlSAlrSltIdx	1.3.6.1.4.1.164.3.1.3.1.2.1.2	INTEGER	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
INT mdlSAlrState	1.3.6.1.4.1.164.3.1.3.1.2.1.6	INTEGER	read-only	State of the alarm.
INT mdlSAlrStatus	1.3.6.1.4.1.164.3.1.3.1.1.1.5	INTEGER	read-only	Indicates the alarm state at module level, i.e. lower level (port alarms) status is not included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSAlrStatusAll	1.3.6.1.4.1.164.3.1.3.1.1.1.6	INTEGER	read-only	Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
mdlSAlrTable	1.3.6.1.4.1.164.3.1.3.1.2		not-accessible	The list of card agent alarms ; includes also an alarm indicating existence of alarms on its ports if there are any.
STR mdlSBackupSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.16	DisplayString	read-only	This attribute indicates the Backup Software version of the card installed in the specific slot position.
INT mdlSCardType	1.3.6.1.4.1.164.3.3.2.1.1.1.2	INTEGER	read-only	This attribute indicates the type of the card installed in the specific slot position. Only PS's are possible in the PS slots. Only CL's are possible in the CL slots. Only IO modules are possible in the IO slots. Kmux card type start with the letter k. LA card type start with the letters la.
INT mdlSClearAllAlrCmd	1.3.6.1.4.1.164.3.1.3.1.1.1.11	INTEGER	read-write	Setting this command to ON, enforces a clear of all the alarms in the given slot, including all its ports alarms. The clear operation will not be applied for masked/inverted alarms.
INT mdlSClearAlrCmd	1.3.6.1.4.1.164.3.1.3.1.1.1.10	INTEGER	read-write	Setting this command to ON, enforces a clear of all the alarms in the given slot, excluding alarms of port level. The clear operation will not be applied for masked/inverted alarms.
I32 mdlSCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.13	Integer32	read-write	General object for any special command at card level. 0=NotApplicable, for cards that don't support this object. For KML.10(ISDN) card of KM-2100, the object will indicate Manual Call Command in Switch mode. It is applicable only when for KML.10, prtIsdnSwitchMode=manual. KML.10 valid values: '1' = noOp, will be used by agents that do not support this feature or object (old KM agents) '2' = off, Set call command mode to disconnect state. Disconnects the call. '3' = on, Set call command mode to connect state. Connects the call. For DXC IO cards, the object will be used for IO Card Reset HW command: '2' = off, this will be always the Get value for these cards. '3' = on, this is the Set command used to Reset the IO card. Upon completing the operation, the value will automatically change to off(2), by Agent. For Slots that are NOT IO Slots and for empty IO Slots, the Get value will be always '0' (NotApplicable).
mdlSEntry	1.3.6.1.4.1.164.3.3.2.1.1.1		not-accessible	An entry in table.
INT mdlSHwStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.8	INTEGER	read-only	This attribute will be fail(2) when a HW FAIL exists on this module (discovered by periodic self test); otherwise the value will be ok(3).
STR mdlSHwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.3	DisplayString	read-only	This attribute indicates the Hardware version of the card installed in the specific slot position.
STR mdlSHwVersion	1.3.6.1.4.1.164.3.1.3.1.1.1.3	DisplayString	read-only	This attribute indicates the Hardware version of the installed card in the specific slot position.
INT mdlSInstCardType	1.3.6.1.4.1.164.3.1.3.1.1.1.2	INTEGER	read-only	This attribute indicates the type of card installed in the specific slot position. Only PS cards are possible in the PS slots. Only CL cards are possible in the CL slots. Only IO cards are possible in the IO slots.
mdlSInstEntry	1.3.6.1.4.1.164.3.1.3.1.1.1		not-accessible	An entry in table.
INT mdlSInstSltIdx	1.3.6.1.4.1.164.3.1.3.1.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the mux. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
mdlSInstTable	1.3.6.1.4.1.164.3.1.3.1.1		not-accessible	A table.
INT mdlSMaskedAlrStat	1.3.6.1.4.1.164.3.1.3.1.1.1.7	INTEGER	read-only	Indicates the alarm state at module level, [i.e. lower level (port alarms) status is not included],including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSMaskedAlrStatAll	1.3.6.1.4.1.164.3.1.3.1.1.1.8	INTEGER	read-only	Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
STR mdlSPiggybackVer	1.3.6.1.4.1.164.3.3.2.1.1.1.18	SnmpAdminString	read-only	This attribute indicates the Piggyback version of the card installed in the specific slot position.
INT mdlSRebuildFrame	1.3.6.1.4.1.164.3.3.2.1.1.1.15	INTEGER	read-write	Applicable only for KiloMux Main Link cards only. '2' = off, this will be always the Get value. '3' = on, this is the Set command used to Rebuild the Frame. Upon completing the operation, the value will automatically change to off(2), by Agent.
INT mdlSReset	1.3.6.1.4.1.164.3.3.2.1.1.1.14	INTEGER	read-write	Reset action to be performed on the module.
STR mdlSSecondaryBackupSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.17	DisplayString	read-only	This attribute indicates the Secondary Backup Software version of the card installed in the specific slot position.
INT mdlSSltIdx	1.3.6.1.4.1.164.3.3.2.1.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the DACS. The Kilomux should use enumerated values starting with kmx. For IPmux100 use values 1-13, 20.
STR mdlSSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.4	DisplayString	read-only	This attribute indicates the Software version of the card installed in the specific slot position.
STR mdlSSwVersion	1.3.6.1.4.1.164.3.1.3.1.1.1.4	DisplayString	read-only	This attribute indicates the Software version of the installed card in the specific slot position.
mdlSTable	1.3.6.1.4.1.164.3.3.2.1.1		not-accessible	A table.
IP mdlStatDefaultGateway	1.3.6.1.4.1.164.3.2.2.2.1.1.4	IpAddress	read-only	Default Gateway's IP Address when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
mdlStatEntry	1.3.6.1.4.1.164.3.2.2.2.1.1		not-accessible	An entry in table.
IP mdlStatHostIP	1.3.6.1.4.1.164.3.2.2.2.1.1.2	IpAddress	read-only	The host interface IP address when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
IP mdlStatHostMask	1.3.6.1.4.1.164.3.2.2.2.1.1.3	IpAddress	read-only	The host interface subnet mask when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
INT mdlStatSltIdx	1.3.6.1.4.1.164.3.2.2.2.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the mux. In the 2104 Unit the entries psB(2),clB(4),io6(10)..io12(16) are not valid.
mdlStatTable	1.3.6.1.4.1.164.3.2.2.2.1		not-accessible	A table.
I32 mdlSTemperature	1.3.6.1.4.1.164.3.1.3.1.1.1.12	Integer32	read-only	Temperature of the card, in Celsius degrees.
INT mdlSTestStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.7	INTEGER	read-only	This attribute will be on(3) when there is at least one test running on a port of the module; otherwise the value will be off(2).
INT mdlSTstStatusAll	1.3.6.1.4.1.164.3.1.3.1.1.1.9	INTEGER	read-only	This attribute will be set to on(3) when there is at least one test in progress on a channel of the card, otherwise the value will be off(2).
mdlWanGen	1.3.6.1.4.1.164.3.1.3
OCT mngAlarmTrapMask	1.3.6.1.4.1.164.6.2.7.1.5	OCTET STRING	read-write	The value of this object determines the alarm traps that the agent should mask (not send to this manager). The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. For more details on the specific alarm traps masked, see product specification.
mngEntry	1.3.6.1.4.1.164.6.2.7.1		not-accessible	An entry in table.
I32 mngID	1.3.6.1.4.1.164.6.2.7.1.1	Integer32	read-only	This value indicates an index of a specific IP address
IP mngIP	1.3.6.1.4.1.164.6.2.7.1.2	IpAddress	read-write	This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.
IP mngIPMask	1.3.6.1.4.1.164.6.2.7.1.3	IpAddress	read-write	This value indicates the mask of the destination addresses of the traps.
U32 mngSnmpTrapUdpPort	1.3.6.1.4.1.164.6.2.7.1.6	Unsigned32	read-write	This variable enables to set the UDP port (socket) used for SNMP traps.
mngTrapIpTable	1.3.6.1.4.1.164.6.2.7		not-accessible	This table indicates the destination address of the traps. Internally it will be limited to ten addresses.
I32 mngTrapMask	1.3.6.1.4.1.164.6.2.7.1.4	Integer32	read-write	The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
NTF modlChangeTrap	1.3.6.1.4.1.164.6.1.0.26			This trap is sent whenever a module is inserted or removed. The trap should include the new module type (e.g. modlParamType).
modlParam	1.3.6.1.4.1.164.6.2.32.1
modlParamEntry	1.3.6.1.4.1.164.6.2.32.1.1.1		not-accessible	An entry in table.
I32 modlParamIndex	1.3.6.1.4.1.164.6.2.32.1.1.1.1	Integer32	read-only	The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4.
OCT modlParamLeds	1.3.6.1.4.1.164.6.2.32.1.1.1.4	OCTET STRING	read-only	This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
INT modlParamReset	1.3.6.1.4.1.164.6.2.32.1.1.1.2	INTEGER	read-write	Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2).
INT modlParamSwdlStatus	1.3.6.1.4.1.164.6.2.32.1.1.1.3	INTEGER	read-only	This parameter indicates whatever the swdl is in process or not.
STR modlParamSwVer	1.3.6.1.4.1.164.6.2.32.1.1.1.6	DisplayString	read-only	This attribute indicates the Module's Software Version.
modlParamTable	1.3.6.1.4.1.164.6.2.32.1.1		not-accessible	This table include parameters for system modules.
INT modlParamType	1.3.6.1.4.1.164.6.2.32.1.1.1.5	INTEGER	read-only	This attribute indicates the Module Type.
NTF moduleFailTrap	1.3.6.1.4.1.164.6.1.0.8			This trap is sent upon a module failure.
NTF moduleInitFailTrap	1.3.6.1.4.1.164.6.1.0.9			This trap is sent upon a module initialization failure.
muxHub	1.3.6.1.4.1.164.3.2
muxHubEvents	1.3.6.1.4.1.164.3.2.0			The events for .
newMasking	1.3.6.1.4.1.164.4.1.6
opticalPort	1.3.6.1.4.1.164.6.2.15.8
INT optPrtCnfgALS	1.3.6.1.4.1.164.6.2.15.8.2.1.3	INTEGER	read-write	enable/disable Automatic Laser Shutdown
optPrtCnfgEntry	1.3.6.1.4.1.164.6.2.15.8.2.1		not-accessible	An entry in table.
U32 optPrtCnfgIdx	1.3.6.1.4.1.164.6.2.15.8.2.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.x.
U32 optPrtCnfgPrtIdx	1.3.6.1.4.1.164.6.2.15.8.2.1.2	Unsigned32	not-accessible	This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
optPrtCnfgTable	1.3.6.1.4.1.164.6.2.15.8.2		not-accessible	A table - optical port configuration
optPrtMonitorEntry	1.3.6.1.4.1.164.6.2.15.8.1.1		not-accessible	An entry in table.
I32 optPrtMonitorLaserBias	1.3.6.1.4.1.164.6.2.15.8.1.1.4	Integer32	read-only	LASER bias current level. Value is given in units of microAmper (uA).
I32 optPrtMonitorLaserTemp	1.3.6.1.4.1.164.6.2.15.8.1.1.5	Integer32	read-only	LASER temperature level, in hundredth (1/100) (C) degrees.
I32 optPrtMonitorPrtIdx	1.3.6.1.4.1.164.6.2.15.8.1.1.1	Integer32	not-accessible	This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
I32 optPrtMonitorRxPower	1.3.6.1.4.1.164.6.2.15.8.1.1.6	Integer32	read-only	Received optical power in units of hundredth (1/100) of dBm.
INT optPrtMonitorSample	1.3.6.1.4.1.164.6.2.15.8.1.1.2	INTEGER	not-accessible	This index indicates historic and current values - minimum, maximum and actual (current) value.
I32 optPrtMonitorSupplyVoltage	1.3.6.1.4.1.164.6.2.15.8.1.1.7	Integer32	read-only	Supply voltage, in hundredth (1/100) of volts (V).
optPrtMonitorTable	1.3.6.1.4.1.164.6.2.15.8.1		not-accessible	A table - optical port (e.g SFP) monitoring parameters, according to SFF-8472 Specification for Diagnostic Monitoring Interface for Optical Xcvrs. and ITU-T rec. G.958
I32 optPrtMonitorTxPower	1.3.6.1.4.1.164.6.2.15.8.1.1.3	Integer32	read-only	Transmitted optical power level. Value is given in units of hundredth (1/100) of dBm.
INT physicalConnector	1.3.6.1.4.1.164.6.2.15.1.1.2	INTEGER	read-only	The connector of the port/interface. other - none of the specified connectors none - no connector.
physicalConnectorEntry	1.3.6.1.4.1.164.6.2.15.1.1		not-accessible	An entry in table.
STR physicalConnectorString	1.3.6.1.4.1.164.6.2.15.1.1.9	SnmpAdminString	read-only	(SFP) connector type. It can be Vendor Specific (unknown in advance). Being a string, the object is not affected by any future new connectors. This object will usually not be used for drawing the connector.
physicalConnectorTable	1.3.6.1.4.1.164.6.2.15.1		not-accessible	This table includes the connector type of ports or interfaces.
I32 pLinkCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 pLinkIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.4	Integer32	read-only	This index is the row number.
I32 pLinkPortNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.6	Integer32	read-write	The port of the prioritized link. Value 100 is for noConnect.
I32 pLinkPrioNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.7	Integer32	read-write	The priority of the prioritized link. MIN=1...., MAX=8.
I32 pLinkPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be the link selector number.
INT pLinkSlotNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.5	INTEGER	read-write	The slot of the prioritized link. For ISDN BRI ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
INT pLinkSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.2	INTEGER	read-only	Slot Index
INT pLinkVRate	1.3.6.1.4.1.164.3.2.3.2.17.3.1.8	INTEGER	read-write	The rate to use with this link.
INT portBalance	1.3.6.1.4.1.164.6.2.15.1.1.5	INTEGER	read-write	This object is according to the port Impedance. For T1 - always balanced. For E1 - there are different impedance values for balanced and unbalanced.
INT portDdmSupport	1.3.6.1.4.1.164.6.2.15.1.1.6	INTEGER	read-only	SFP (Small Form Pluggable) port -support Digital Diagnostics Monitoring.
I32 portIdx	1.3.6.1.4.1.164.6.2.15.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
STR portMfgName	1.3.6.1.4.1.164.6.2.15.1.1.7	SnmpAdminString	read-only	(SFP) Port Manufacturer name (Maximum - 16 characters).
INT portOptMode	1.3.6.1.4.1.164.6.2.15.1.1.4	INTEGER	read-only	Laser Mode of an Optical Laser interface/port. notApplicable - for non-Laser ports.
INT portOptWaveLength	1.3.6.1.4.1.164.6.2.15.1.1.3	INTEGER	read-only	Wave Length of an Optical interface/port in [nm] and specification if Laser or not. notApplicable - for non-optical ports.
portQos	1.3.6.1.4.1.164.6.3.4
I32 portTrafficClass	1.3.6.1.4.1.164.6.3.5.1.1.3	Integer32	read-write	This object indicates the Traffic Class level of this port.
portTrafficClassEntry	1.3.6.1.4.1.164.6.3.5.1.1		not-accessible	An entry in portTrafficClassTable.
I32 portTrafficClassIdx1	1.3.6.1.4.1.164.6.3.5.1.1.1	Integer32	not-accessible	This attribute indicates the 1st index of the table. This may be the Idx of the Cnfg(1..255) being accessed; Idx of 255 relates to the TmpCnfg, or any other Index.
I32 portTrafficClassPortIdx	1.3.6.1.4.1.164.6.3.5.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
portTrafficClassTable	1.3.6.1.4.1.164.6.3.5.1		not-accessible	Mapping of port to Traffic Class level.
U32 portTypicalMaxRange	1.3.6.1.4.1.164.6.2.15.1.1.8	Unsigned32	read-only	Maximum range supported by SFP port, in meter units.
STR portVendorPartNo	1.3.6.1.4.1.164.6.2.15.1.1.10	SnmpAdminString	read-only	SFP Vendor Part Number. Being a string, the object is not affected by any future new SFPs.
INT prtAcmActiveState	1.3.6.1.4.1.164.3.2.3.2.20.1.1.5	INTEGER	read-write	This attribute indicates the Electric Active State of the port.
STR prtAcmAlrString	1.3.6.1.4.1.164.3.2.3.2.20.1.1.6	DisplayString	read-write	Alarm string selected by user for the Inbound ports. This object is applicable only for the Inbound Ports: ext-5..ext-12. For the Outbound Ports (ext-1..ext-4), the size of this string will be 0.
prtAcmCnfg	1.3.6.1.4.1.164.3.2.3.2.20
prtAcmCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.20.1.1		not-accessible	An entry in table.
I32 prtAcmCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
prtAcmCnfgTable	1.3.6.1.4.1.164.3.2.3.2.20.1		not-accessible	This is a table for ACM port parameters.
INT prtAcmConnect	1.3.6.1.4.1.164.3.2.3.2.20.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.
INT prtAcmPrtIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtAcmSltIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
I32 prtAgendaBehaviourCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtAgendaBehaviourEntry	1.3.6.1.4.1.164.3.1.4.2.2.1.1		not-accessible	An entry in table.
INT prtAgendaBehaviourOnOff	1.3.6.1.4.1.164.3.1.4.2.2.1.1.4	INTEGER	read-write	Setting this command to on(3) enables the agenda function at module (3000) or port (300/30) level.
I32 prtAgendaBehaviourPrtIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.3	Integer32	read-only	This parameter should be: - port number for MX300/30 - 100 = N/A for MX3000.
I32 prtAgendaBehaviourSltIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.2	Integer32	read-only	This parameter should be: - slot number for MX3000 - 255 = N/A for MX300/30.
prtAgendaBehaviourTable	1.3.6.1.4.1.164.3.1.4.2.2.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
I32 prtAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.4.3.3.1.4	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
I32 prtAlarmsCmprAlarmPort	1.3.6.1.4.1.164.3.1.4.3.3.1.3	Integer32	read-only	This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a non-existing port. IP Bundles are considered a port too, for this matter.
I32 prtAlarmsCmprAlarmSlot	1.3.6.1.4.1.164.3.1.4.3.3.1.2	Integer32	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For Stand-alone units, notApplicable(255) will appear.
prtAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.4.3.3.1		not-accessible	An entry in table.
OCT prtAlarmsCmprObj	1.3.6.1.4.1.164.3.1.4.3.3.1.5	OCTET STRING	read-only	This attribute is the compressed information itself.
prtAlarmsCmprTable	1.3.6.1.4.1.164.3.1.4.3.3		not-accessible	A table.
I32 prtAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.4.3.3.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
prtAlr	1.3.6.1.4.1.164.3.3.3.1.4
OCT prtAlrMask	1.3.6.1.4.1.164.3.3.3.1.4.2.1.2	OCTET STRING	read-write	This object is a mask that indicates which port level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the port level will be 0. This object is applicable only when prtGenAlrMaskAll=off (otherwise all port alarms are masked). Example: When Alarms having the codes 31 and 40 are masked, the value of this object will be 10080000000 (hex).
prtAlrMaskEntry	1.3.6.1.4.1.164.3.3.3.1.4.2.1		not-accessible	An entry in table.
I32 prtAlrMaskPrtIdx	1.3.6.1.4.1.164.3.3.3.1.4.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
prtAlrMaskTable	1.3.6.1.4.1.164.3.3.3.1.4.2		not-accessible	A table.
I32 prtBdbandCnfgIdx	1.3.6.1.4.1.164.3.1.6.8.1.1.1.1	Integer32	read-only	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
I32 prtBdbandIdx	1.3.6.1.4.1.164.3.1.6.8.1.1.1.2	Integer32	read-only	This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.
prtBdbandIndEntry	1.3.6.1.4.1.164.3.1.6.8.1.1.1		not-accessible	An entry in the Indication Signal table.
INT prtBdbandIndEvent	1.3.6.1.4.1.164.3.1.6.8.1.1.1.4	INTEGER	read-only	This object indicates a unique Event that can cause the Indication Signal. slm(2) = SLM = Signal Label Mismatch eed(4) = EED = Excessive Error Defect pathTrace(5) = the end-to-end source/destination of information is wrong. lom(6) = LOM = Loss of Multiframe. lop(7) = LOP = Loss of Pointer. slu(8) = SLU = Signal Label Unequipped.
INT prtBdbandIndSig	1.3.6.1.4.1.164.3.1.6.8.1.1.1.3	INTEGER	read-only	This object indicates a unique Indication Signal. ais(1) = AIS = Alarm Indication Signal. rdi(2) = RDI = Remote Defect Indication.
INT prtBdbandIndSigEnable	1.3.6.1.4.1.164.3.1.6.8.1.1.1.5	INTEGER	read-create	This object allows user to define if the event specified by prtBdbandIndEvent will cause creation of the Indication Signal specified by prtBdbandIndSig or not. disable - will not enable causing the signal enable - will enable causing the signal.
prtBdbandIndTable	1.3.6.1.4.1.164.3.1.6.8.1.1		not-accessible	The Indication Signal table.
ROW prtBdbandRowStatus	1.3.6.1.4.1.164.3.1.6.8.1.1.1.6	RowStatus	read-create	Creation/Deletion of rows in the table.
INT prtBertClearCounters	1.3.6.1.4.1.164.3.3.3.1.5.1.10	INTEGER	read-write	Setting this object to ON, will enforce a clear operation of some BERT Counters. Upon completion, the value will automatically change to off(2).
I32 prtBertCounter	1.3.6.1.4.1.164.6.2.15.4.1.1.3	Integer32	read-only	This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counter starts from zero (0) anytime BERT is initiated.
prtBertEntry	1.3.6.1.4.1.164.3.3.3.1.5.1		not-accessible	An entry in table.
I32 prtBertErrorBits	1.3.6.1.4.1.164.3.3.3.1.5.1.9	Integer32	read-only	How many Error Bits were detected since BERT started to run.
I32 prtBertESs	1.3.6.1.4.1.164.3.3.3.1.5.1.7	Integer32	read-only	How many Errored Seconds were detected since BERT started to run. Counter for Kmux and MP.
INT prtBertInjectErrRateCmd	1.3.6.1.4.1.164.3.3.3.1.5.1.4	INTEGER	read-write	This object controls activation/deactivation of the Error Rate Injection during BERT.
INT prtBertInjectRate	1.3.6.1.4.1.164.3.3.3.1.5.1.3	INTEGER	read-write	This object indicates the error rate injection of the BERT. r10Emx = 10E-x This object is the same for all configurations. single - single error injection. notApplicable - when this object is not supported.
INT prtBertInjectSingleErrCmd	1.3.6.1.4.1.164.3.3.3.1.5.1.5	INTEGER	read-write	This object enables to initiate a Single Error Injection during BERT (on). Upon completion, the value will automatically change to off(2).
INT prtBertPattern	1.3.6.1.4.1.164.3.3.3.1.5.1.2	INTEGER	read-write	This object indicates the pattern of the BERT. p2Exxm1 = 2Exx-1. pxx = pattern xx. This object is the same for all configurations. notApplicable - when this object is not supported.
I32 prtBertPrtIdx	1.3.6.1.4.1.164.3.3.3.1.5.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the MP : - first two digits will be: (IO slot number+10) - last one/two digits will be according to the external port number within the card: exPrt1 -> 1 exPrt2 -> 3 exPrt3 -> 5 exPrt4 -> 7 .
STR prtBertResult	1.3.6.1.4.1.164.3.3.3.1.5.1.13	DisplayString	read-only	This object indicates Result of BERT for the selected port (number of error bits divided to the total number of data bits.) Applicable only if BERT is running on this port Agents that do not support this feature will send SIZE 0.
I32 prtBertRunTime	1.3.6.1.4.1.164.3.3.3.1.5.1.6	Integer32	read-only	This object indicates how much time (seconds) passed since BERT started to run.
I32 prtBertRxBits	1.3.6.1.4.1.164.3.3.3.1.5.1.15	Integer32	read-only	How many data bits were Received since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
I32 prtBertSyncLoss	1.3.6.1.4.1.164.3.3.3.1.5.1.8	Integer32	read-only	How many times Sync Loss was detected since BERT started to run. For some products: number of seconds in which Sync Loss occured since BERT started to run. See product specification.
INT prtBertSyncStatus	1.3.6.1.4.1.164.3.3.3.1.5.1.11	INTEGER	read-only	Sync Status while BERT runs.
prtBertTable	1.3.6.1.4.1.164.3.3.3.1.5		not-accessible	This table includes the BERT parameters, counters and commands. The configurable parameters: - prtBertPattern - prtBertInjectRate - prtBertTs are not Set per configuration (same for all Configurations) but start being applied by the Agent only upon successful Update/Download operation. Therefore, Set will enter the values to the Temporary Configuration of the agent, while Get will get the values of the Active Configuration.
OCT prtBertTs	1.3.6.1.4.1.164.3.3.3.1.5.1.12	OCTET STRING	read-write	This object indicates on which TSs of the selected port, BERT should be applied. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - BERT should be applied on this TS. For a T1 port, the valid raised bits ('1') are: 1..25. For an E1 port, the valid raised bits ('1') are: 1..31. Agents that do not support this feature will send SIZE 0.
I32 prtBertTxBits	1.3.6.1.4.1.164.3.3.3.1.5.1.14	Integer32	read-only	How many data bits were transmitted since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
I32 prtBertTxErrorBits	1.3.6.1.4.1.164.3.3.3.1.5.1.16	Integer32	read-only	Number of injected error bits since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
prtCfgParam	1.3.6.1.4.1.164.3.3.3.1.7
I32 prtCfgParamCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.7.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtCfgParamEntry	1.3.6.1.4.1.164.3.3.3.1.7.1.1		not-accessible	An entry in table.
I32 prtCfgParamIdx	1.3.6.1.4.1.164.3.3.3.1.7.1.1.2	Integer32	read-only	A unique identifier of the port (within the card when applicable). - For KM-2100: Slot*100+Ch external ports: Ch=1..10 internal ports (sub-channels): Ch=11..20. - For FCD-T1/E1(L): MAIN=111, SUB=113, CH1=122, CH2=124. - For other devices, see specific device's spec.
STR prtCfgParamInbandLoopActPattern	1.3.6.1.4.1.164.3.3.3.1.7.1.1.9	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtCfgParamInbandLoopPatternCfg=userConfig.
STR prtCfgParamInbandLoopDeactPattern	1.3.6.1.4.1.164.3.3.3.1.7.1.1.10	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtCfgParamInbandLoopPatternCfg=userConfig.
INT prtCfgParamInbandLoopDetection	1.3.6.1.4.1.164.3.3.3.1.7.1.1.7	INTEGER	read-write	Inband Loop Detection. The field is relevant for FCD-T1/E1(L) ports.
INT prtCfgParamInbandLoopPatternCfg	1.3.6.1.4.1.164.3.3.3.1.7.1.1.8	INTEGER	read-write	This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtCfgParamInbandLoopActPattern and prtCfgParamInbandLoopDeactPattern.
INT prtCfgParamMlAtoMlBPrio	1.3.6.1.4.1.164.3.3.3.1.7.1.1.5	INTEGER	read-write	ML-A to ML-B Priority. The field is relevant only for ML modes of Priority Bumping and Switched Backup.
INT prtCfgParamMlBtoMlAPrio	1.3.6.1.4.1.164.3.3.3.1.7.1.1.6	INTEGER	read-write	ML-B to ML-A Priority. The field is relevant only for ML modes of Priority Bumping.
INT prtCfgParamOperatedMl	1.3.6.1.4.1.164.3.3.3.1.7.1.1.4	INTEGER	read-write	The main link for this channel. The field is relevant only for ML modes of Dual, Priority Bumping and Switched Backup.
INT prtCfgParamSlt	1.3.6.1.4.1.164.3.3.3.1.7.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid. notApplicable(255) - for products that do not have Slots.
prtCfgParamTable	1.3.6.1.4.1.164.3.3.3.1.7.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. KMUX parameters are for the cards: KMBE/New, KVF.6 family.
prtClCnfg	1.3.6.1.4.1.164.3.2.3.2.1
prtClkSrc	1.3.6.1.4.1.164.6.2.15.7
NTF prtClkSrcChangeTrap	1.3.6.1.4.1.164.6.1.0.7			This trap is sent upon any port clock change.
I32 prtClkSrcCnfgIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
prtClkSrcEntry	1.3.6.1.4.1.164.6.2.15.7.1.1		not-accessible	An entry in table.
INT prtClkSrcIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.3	INTEGER	not-accessible	An index in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
INT prtClkSrcMode	1.3.6.1.4.1.164.6.2.15.7.1.1.4	INTEGER	read-write	This entry indicates the source the nodal timing is locked to.
I32 prtClkSrcPrt	1.3.6.1.4.1.164.6.2.15.7.1.1.5	Integer32	read-write	This entry is valid only when working in rxClk mode. It specifies the port from which the clock willl be taken. Refer to device specification for source port Index
I32 prtClkSrcPrtIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index (receiving clock). Refer to device specification for port Index
prtClkSrcTable	1.3.6.1.4.1.164.6.2.15.7.1		not-accessible	A table - Parameters for master and fallback clock source of ports .
I32 prtCmprCnfgIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
prtCmprEntry	1.3.6.1.4.1.164.3.1.4.3.1.1		not-accessible	An entry in table.
OCT prtCmprObj	1.3.6.1.4.1.164.3.1.4.3.1.1.6	OCTET STRING	read-write	This attribute is the compressed information itself.
I32 prtCmprPrtIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.5	Integer32	read-only	This attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148).
INT prtCmprSltIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
OCT prtCmprStatisticObj	1.3.6.1.4.1.164.3.1.4.3.1.1.7	OCTET STRING	read-only	This attribute is the compressed statistics information itself.
prtCmprTable	1.3.6.1.4.1.164.3.1.4.3.1		not-accessible	A table.
I32 prtCmprTypIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 prtCmprVersion	1.3.6.1.4.1.164.3.1.4.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
prtCnfgAgenda	1.3.6.1.4.1.164.3.1.4.2.2
I32 prtCnfgAgendaCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtCnfgAgendaDayIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.4	INTEGER	read-only	This attribute for which day of the week this row applies.
prtCnfgAgendaEntry	1.3.6.1.4.1.164.3.1.4.2.2.2.1		not-accessible	An entry in table.
I32 prtCnfgAgendaFrom	1.3.6.1.4.1.164.3.1.4.2.2.2.1.6	Integer32	read-write	Start from time interval in seconds.
I32 prtCnfgAgendaPrtIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.3	Integer32	read-only	This attribute is equal to: - port number for MX300/30 - port number for MX3000. For example 1-4 in MHS-4 cards. - 100 = N/A for MX3000 when not used.
I32 prtCnfgAgendaSesId	1.3.6.1.4.1.164.3.1.4.2.2.2.1.5	Integer32	read-only	The user may define 4 different active intervals per day.
I32 prtCnfgAgendaSltIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.2	Integer32	read-only	This attribute is equal to: -slot number for MX3000 -255 = N/A for MX300/30
prtCnfgAgendaTable	1.3.6.1.4.1.164.3.1.4.2.2.2		not-accessible	This table allows the user to schedule the time a session is active per week basis.
I32 prtCnfgAgendaTo	1.3.6.1.4.1.164.3.1.4.2.2.2.1.7	Integer32	read-write	To time interval in seconds.
I32 prtControlCnfg	1.3.6.1.4.1.164.6.2.15.5.1.1.2	Integer32	read-write	This object may be used for port RW general parameter/s. For detailed meaning, see product's spec. Supported by: PRBi-E3/T3. For ACE2002: This parameter will include the value of the new index generated by agent. For Optimux-T3 and OP-155-1: This parameter will be used for Release Remote LLB Command: on=2= Set value only. Command to release LLB of Remote Unit. Agent will return automatically to 'off' value after performing the command. off=3=Get value only. For LA140 This parameter will be used as EchoCanceler per timeslot off = 2 Echo Canceler is disabled on = 3 Echo Canceler is enabled For FCD-155 This parameter will be used to select the port that is clock source for a PDH port, For E1/T1 PDH VC12/VT1.5 = 2 SDH/SONET = 3 For E3/T3 PDH VC3/DS3 = 2 SDH/SONET = 3 For ACE-52 This parameter will be used as Transmit Frame Type, i.e. which type of frame the corresponding bridge port will transmit: Untagged = 2 Tagged = 3 .
C32 prtCrRxDataCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.7	Counter32	read-only	The number of Data Cells received by this port during the selected interval.
C32 prtCrRxTotalCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.5	Counter32	read-only	The total number of cells received by this port during the selected interval.
prtCrStatis	1.3.6.1.4.1.164.3.1.4.1.3.2
prtCrStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1		not-accessible	An entry in table.
INT prtCrStatisInvIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.3	INTEGER	read-only	The Interval of 15 min. for which the following statistics counters are applicable.
INT prtCrStatisPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtCrStatisSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
prtCrStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.2.1		not-accessible	This table is applicable only for an active port running a CR protocol .
I32 prtCrTimeElapsed	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.4	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0.
C32 prtCrTxDataCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.8	Counter32	read-only	The number of Data Cells sent by this port during the selected interval.
C32 prtCrTxTotalCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.6	Counter32	read-only	The total number of cells sent by this port during the selected interval.
prtDacsMux	1.3.6.1.4.1.164.3.3.3
I32 prtDest	1.3.6.1.4.1.164.3.3.3.5.2.1.4	Integer32	read-write	Destination port,(of a T1/E1 port), that is connected to the DIM card, for the specified Destination number. 0 = No destination port. Else: For external ports: (IO Slot+10) & 1 for port 1 (IO Slot+10) & 3 for port 2 Example: port2 of IO slot 12 will be: 223 . For internal ports : (IO Slot+10) & 2 for port 1 (IO Slot+10) & 4 for port 2 (IO Slot+10) & 6 for port 3 (IO Slot+10) & 8 for port 4, etc...
I32 prtDestCnfgIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
INT prtDestConnect	1.3.6.1.4.1.164.3.3.3.5.2.1.5	INTEGER	read-only	Connection Status of the specified destination number. For a specified destination port, it depends both on the status of the port and on the status of the far-end port. Since this is a RO object, same value will be received for all configurations.
I32 prtDestDimIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.2	Integer32	read-only	This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10) & 1 Example: port1 of IO slot 11 will be: 211 .
I32 prtDestIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.3	Integer32	read-only	This attribute indicates a destination number of the DIM card.
prtDim	1.3.6.1.4.1.164.3.3.3.5
INT prtDimClkMode	1.3.6.1.4.1.164.3.3.3.5.1.1.5	INTEGER	read-write	Clock Mode. smooth - a clock that is not 'pulsed'(has no 'gaps'). In this mode the DXC does NOT receive back the clock signal. extSmooth - same as 'smooth' but in this mode, the DXC receives back the clock signal.
prtDimCnfgEntry	1.3.6.1.4.1.164.3.3.3.5.1.1		not-accessible	The write operation into the Table Objects is valid only for the TmpCnfg entry (prtDimCnfgIdx=255).
I32 prtDimCnfgIdx	1.3.6.1.4.1.164.3.3.3.5.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
prtDimCnfgTable	1.3.6.1.4.1.164.3.3.3.5.1		not-accessible	A table.
prtDimDestEntry	1.3.6.1.4.1.164.3.3.3.5.2.1		not-accessible	The write operation is valid only for the TmpCnfg entry (prtDimDestCnfgIdx=255).
prtDimDestTable	1.3.6.1.4.1.164.3.3.3.5.2		not-accessible	A table.
I32 prtDimIdx	1.3.6.1.4.1.164.3.3.3.5.1.1.2	Integer32	read-only	This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10)*10 + 1 Example: port1 of IO slot 11 will be: 211 .
INT prtDimMaxDelay	1.3.6.1.4.1.164.3.3.3.5.1.1.6	INTEGER	read-write	Max Delay permitted between the links, in msec.
INT prtDimMng	1.3.6.1.4.1.164.3.3.3.5.1.1.7	INTEGER	read-write	Use of DIM port for management. disabled - no management on DIM ts1 - 1 bit of TS1 is used for management.
INT prtDimMngRoutProt	1.3.6.1.4.1.164.3.3.3.5.1.1.8	INTEGER	read-write	Mng Routing Protocol of the port. none - when prtDimMng is 'disabled'.
INT prtDimPolarity	1.3.6.1.4.1.164.3.3.3.5.1.1.4	INTEGER	read-write	Polarity.
INT prtDimTxMode	1.3.6.1.4.1.164.3.3.3.5.1.1.3	INTEGER	read-write	Tx mode. regularTx - the links are connected to a similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is decreased accordingly. broadcast - the links are connected to MORE than one similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is not affected
I32 prtDlciCmprCnfgIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.1	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 prtDlciCmprDlciIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.5	Integer32	read-only	This attribute indicates a unique identifier of the Dlci the compressed information relates to. The values are between 16 - 991.
prtDlciCmprEntry	1.3.6.1.4.1.164.3.1.4.3.2.1		not-accessible	An entry in table.
OCT prtDlciCmprObj	1.3.6.1.4.1.164.3.1.4.3.2.1.6	OCTET STRING	read-write	This attribute is the compressed information itself.
INT prtDlciCmprPrtIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.4	INTEGER	read-only	This attribute indicates a unique identifier of the port the compressed information relates to. All the values are valid.
INT prtDlciCmprSltIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.3	INTEGER	read-only	This attribute indicates a unique number of the slot position where the module is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
prtDlciCmprTable	1.3.6.1.4.1.164.3.1.4.3.2		not-accessible	A table.
I32 prtDlciCmprVersion	1.3.6.1.4.1.164.3.1.4.3.2.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 prtDlciIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.3	Integer32	read-only	This attribute indicates a unique DLCI index for each valid DLCI (16..991).
INT prtDlciPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
C32 prtDlciRxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.14	Counter32	read-only	Number of data frames received by this DLCI, exceeding the Burst Committed value.
C32 prtDlciRxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.12	Counter32	read-only	Number of data frames received by this DLCI, exceeding the Burst Excess value.
C32 prtDlciRxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.8	Counter32	read-only	All the frames discarded due to congestion, received by this DLCI.
C32 prtDlciRxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.6	Counter32	read-only	The number of De frames discarded due to congestion, received by this DLCI.
C32 prtDlciRxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.4	Counter32	read-only	The number of De frames received by this DLCI.
INT prtDlciSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
prtDlciStatis	1.3.6.1.4.1.164.3.1.4.1.3.3
prtDlciStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1		not-accessible	An entry in table.
prtDlciStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.3.1		not-accessible	This table is applicable only for an active port running an FR, FR+ or CR protocol, with valid DLCIs .
C32 prtDlciTxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.15	Counter32	read-only	Number of data frames sent by this DLCI, exceeding the Burst Committed value.
C32 prtDlciTxBecn	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.11	Counter32	read-only	Number of frames sent by this DLCI, indicating backward congestion.
C32 prtDlciTxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.13	Counter32	read-only	Number of data frames sent by this DLCI, exceeding the Burst Excess value.
C32 prtDlciTxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.9	Counter32	read-only	All the frames discarded due to congestion, sent by this DLCI.
C32 prtDlciTxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.7	Counter32	read-only	The number of De frames discarded due to congestion, sent by this DLCI.
C32 prtDlciTxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.5	Counter32	read-only	The number of De frames sent by this DLCI.
C32 prtDlciTxFecn	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.10	Counter32	read-only	Number of frames sent by this DLCI, indicating forward congestion.
prtDS1Events	1.3.6.1.4.1.164.3.1.6.4.0
prtDs1PerfHistory	1.3.6.1.4.1.164.3.1.6.4.1
G32 prtDs3CurrentAIS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.4	Gauge32	read-only	The counter associated with the number of AIS seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentBIP	1.3.6.1.4.1.164.3.1.6.3.1.2.1.7	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentBitParity	1.3.6.1.4.1.164.3.1.6.3.1.2.1.12	Gauge32	read-only	Bit Parity Error counter. Relevant to T3 only.
G32 prtDs3CurrentBPV	1.3.6.1.4.1.164.3.1.6.3.1.2.1.17	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the current 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.
prtDs3CurrentEntry	1.3.6.1.4.1.164.3.1.6.3.1.2.1		not-accessible	An entry in the DS3 Current table.
G32 prtDs3CurrentES	1.3.6.1.4.1.164.3.1.6.3.1.2.1.11	Gauge32	read-only	The number of Errored Seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentFEBE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.8	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentLCE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.18	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the current 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.
G32 prtDs3CurrentLOC	1.3.6.1.4.1.164.3.1.6.3.1.2.1.3	Gauge32	read-only	The counter associated with the number of LOC seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentLOS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.1	Gauge32	read-only	The counter associated with the number of LOS seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentOOF	1.3.6.1.4.1.164.3.1.6.3.1.2.1.2	Gauge32	read-only	The counter associated with the number of OOF seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentPlcpBIP	1.3.6.1.4.1.164.3.1.6.3.1.2.1.15	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentPlcpFEBE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.16	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentPlcpLOF	1.3.6.1.4.1.164.3.1.6.3.1.2.1.13	Gauge32	read-only	The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configuration If frame types only.
G32 prtDs3CurrentPlcpRAI	1.3.6.1.4.1.164.3.1.6.3.1.2.1.14	Gauge32	read-only	Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentRDI	1.3.6.1.4.1.164.3.1.6.3.1.2.1.5	Gauge32	read-only	The counter associated with the number of RDI seconds, encountered by a DS3 interface.
G32 prtDs3CurrentSES	1.3.6.1.4.1.164.3.1.6.3.1.2.1.10	Gauge32	read-only	The counter associated with the number of SES encountered by a E3 interface in the current 15 minute interval.
G32 prtDs3CurrentSLM	1.3.6.1.4.1.164.3.1.6.3.1.2.1.9	Gauge32	read-only	The counter associated with the number of SLM seconds, encountered by an E3 (only ) interface in the current 15 minute interval.
OCT prtDs3CurrentStatus	1.3.6.1.4.1.164.3.1.6.3.1.2.1.19	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
prtDs3CurrentTable	1.3.6.1.4.1.164.3.1.6.3.1.2		not-accessible	The DS3 Current table.
G32 prtDs3CurrentUAS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.6	Gauge32	read-only	The counter associated with the number of UAS, encountered by a SONET interface.
prtDs3IfEntry	1.3.6.1.4.1.164.3.1.6.3.1.1.1		not-accessible	An entry in the DS3 interface table.
I32 prtDs3IfTimeElapsed	1.3.6.1.4.1.164.3.1.6.3.1.1.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
I32 prtDs3IfValidIntervals	1.3.6.1.4.1.164.3.1.6.3.1.1.1.2	Integer32	read-only	The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
G32 prtDs3IntervalAIS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.5	Gauge32	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalBIP	1.3.6.1.4.1.164.3.1.6.3.1.3.1.8	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalBitParity	1.3.6.1.4.1.164.3.1.6.3.1.3.1.13	Gauge32	read-only	Bit Parity Error counter. Relevant to T3 only.
G32 prtDs3IntervalBPV	1.3.6.1.4.1.164.3.1.6.3.1.3.1.18	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.
prtDs3IntervalEntry	1.3.6.1.4.1.164.3.1.6.3.1.3.1		not-accessible	An entry in the DS3 Interval table.
G32 prtDs3IntervalES	1.3.6.1.4.1.164.3.1.6.3.1.3.1.12	Gauge32	read-only	The number of Errored Seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalFEBE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.9	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalLCE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.19	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.
G32 prtDs3IntervalLOC	1.3.6.1.4.1.164.3.1.6.3.1.3.1.4	Gauge32	read-only	The counter associated with the number of LOC seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalLOS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.2	Gauge32	read-only	The counter associated with the number of LOS seconds , encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
I32 prtDs3IntervalNumber	1.3.6.1.4.1.164.3.1.6.3.1.3.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 prtDs3IntervalOOF	1.3.6.1.4.1.164.3.1.6.3.1.3.1.3	Gauge32	read-only	The counter associated with the number of OOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalPlcpBIP	1.3.6.1.4.1.164.3.1.6.3.1.3.1.16	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalPlcpFEBE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.17	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalPlcpLOF	1.3.6.1.4.1.164.3.1.6.3.1.3.1.14	Gauge32	read-only	The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configuration If frame types only.
G32 prtDs3IntervalPlcpRAI	1.3.6.1.4.1.164.3.1.6.3.1.3.1.15	Gauge32	read-only	Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalRDI	1.3.6.1.4.1.164.3.1.6.3.1.3.1.6	Gauge32	read-only	The counter associated with the number of RDI seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalSES	1.3.6.1.4.1.164.3.1.6.3.1.3.1.11	Gauge32	read-only	The counter associated with the number of SES encountered by a E3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalSLM	1.3.6.1.4.1.164.3.1.6.3.1.3.1.10	Gauge32	read-only	The counter associated with the number of SLM seconds, encountered by an E3 interface in one of the previous 96, individual 15 minute, intervals.
OCT prtDs3IntervalStatus	1.3.6.1.4.1.164.3.1.6.3.1.3.1.20	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
prtDs3IntervalTable	1.3.6.1.4.1.164.3.1.6.3.1.3		not-accessible	The DS3 Interval table.
G32 prtDs3IntervalUAS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.7	Gauge32	read-only	The counter associated with the number of UAS, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
prtDs3PerfHistory	1.3.6.1.4.1.164.3.1.6.3.1
G32 prtDs3TotalBPV	1.3.6.1.4.1.164.3.1.6.3.1.4.1.17	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
prtDs3TotalEntry	1.3.6.1.4.1.164.3.1.6.3.1.4.1		not-accessible	An entry of Total table.
G32 prtDs3TotalLCE	1.3.6.1.4.1.164.3.1.6.3.1.4.1.18	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
G32 prtDs3TotalSES	1.3.6.1.4.1.164.3.1.6.3.1.4.1.19	Gauge32	read-only	Number of SES (Severely Errored Seconds) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
prtDs3TotalTable	1.3.6.1.4.1.164.3.1.6.3.1.4		not-accessible	A list of Total entries.
G32 prtDs3TotalUAS	1.3.6.1.4.1.164.3.1.6.3.1.4.1.6	Gauge32	read-only	Number of UASs (Unavailable Seconds) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
prtE2Cnfg	1.3.6.1.4.1.164.3.2.3.2.21
prtE2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.21.1.1		not-accessible	An entry in table.
I32 prtE2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
prtE2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.21.1		not-accessible	This is a table for E2 port parameters.
INT prtE2Connect	1.3.6.1.4.1.164.3.2.3.2.21.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.
INT prtE2MngOnNationalBit	1.3.6.1.4.1.164.3.2.3.2.21.1.1.5	INTEGER	read-write	This attribute indicates whether National Bit will be used for Management or not.
INT prtE2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtE2SltIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
prtExClCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.1.1.1		not-accessible	All the entries at this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only to the TmpCnfg entry.
I32 prtExClCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExClCnfgTable	1.3.6.1.4.1.164.3.2.3.2.1.1		not-accessible	A table.
INT prtExClDataBits	1.3.6.1.4.1.164.3.2.3.2.1.1.1.6	INTEGER	read-only	This attribute indicates the number of data bits in async frame
INT prtExClEnabled	1.3.6.1.4.1.164.3.2.3.2.1.1.1.10	INTEGER	read-only	This attribute indicates if Ethernet port of CL is enabled or not for management. It is applicable only on the ETH port of the CL, when the MP includes an ML-IP card. disabled - will happen when there is Inband Management via the ML-IP link/s enabled - will happen when ML-IP link/s is not used for Inband Management, but CL's ETH port .
INT prtExClParity	1.3.6.1.4.1.164.3.2.3.2.1.1.1.7	INTEGER	read-only	This attribute indicates if the parity operation mode in async frame
INT prtExClPrtIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtExClRate	1.3.6.1.4.1.164.3.2.3.2.1.1.1.5	INTEGER	read-only	This attribute indicates the operation rate of the port.
INT prtExClRoutingProtocol	1.3.6.1.4.1.164.3.2.3.2.1.1.1.9	INTEGER	read-only	This attribute indicates the routing protocol of the port. When prtExClUsage is nmsSlip or nmsPpp - all values are applicable . Else - only 'none' is applicable.
INT prtExClSltIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. Because the second Cl is only for redundancy, all the parameters are identical in the two modules, i.e. change of any parameter in one module will change automatically the value of the other module.. In the ?004 Unit the entry clB(4) is not valid.
INT prtExClStopBits	1.3.6.1.4.1.164.3.2.3.2.1.1.1.8	INTEGER	read-only	This attribute indicates the minimum number of stop bits in the tx async frame
INT prtExClUsage	1.3.6.1.4.1.164.3.2.3.2.1.1.1.4	INTEGER	read-only	This attribute indicates what is the usage of the port.
prtExHs4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.7.1.1		not-accessible	An entry in table.
I32 prtExHs4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExHs4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.7.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExHs4Connect	1.3.6.1.4.1.164.3.2.3.2.7.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithm. It also affects all the module considerations because the card has only one external (physical) interface.
I32 prtExHs4IdleCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.11	Integer32	read-write	Type value(00 - FF HEX), excluding 0H,8H,10H,12H,21H,24H, 42H,49H,84H,92H
INT prtExHs4LineCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.6	INTEGER	read-write	This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the MPH.1/T1 and E1 line code parameters for the MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExHs4LineLen	1.3.6.1.4.1.164.3.2.3.2.7.1.1.7	INTEGER	read-write	This attribute is the line length parameter used only for T1 interfaces. len399p533ft=len-399-533ft
INT prtExHs4LineType	1.3.6.1.4.1.164.3.2.3.2.7.1.1.5	INTEGER	read-write	This attribute is the line type parameter for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the HS-4/1 and E1 line code parameters for the HS-4/2. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) dsx1ESF (2) dsx1D4 (3) dsx1E1 (4) dsx1E1-CRC (5) dsx1E1-MF (6) dsx1E1-MF-CRC (7)
INT prtExHs4MfClkSrcPrt	1.3.6.1.4.1.164.3.2.3.2.7.1.1.13	INTEGER	read-write	A unique number to identify a port position in the mux if the MultiFrame clock source is valid (YES). inPrt1 - for MTML-H/E1 cards.
INT prtExHs4MfClkSrcSlt	1.3.6.1.4.1.164.3.2.3.2.7.1.1.12	INTEGER	read-write	This attribute indicates whether the port Tx is multiframe synchronized with Rx multiframe of another port and the slot position of that port. This opration is required in order to bypass signaling of PCM voice channels. When its value is Local(2) there is no meaning to 'prtExHs4MfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExHs4OosCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.10	INTEGER	read-write	OOS Code
INT prtExHs4OosSig	1.3.6.1.4.1.164.3.2.3.2.7.1.1.9	INTEGER	read-write	Out of Service signal type.
INT prtExHs4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExHs4RestoreT	1.3.6.1.4.1.164.3.2.3.2.7.1.1.8	INTEGER	read-write	Time passing from the disappearance of the loss of synchronization condition (red alarm), to the restoration of normal service.
INT prtExHs4SltIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
I32 prtExHs4TsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExHs4TsCnfgTable	1.3.6.1.4.1.164.3.2.3.2.7.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExHs4TsEntry	1.3.6.1.4.1.164.3.2.3.2.7.2.1		not-accessible	An entry in table.
INT prtExHs4TsIConPrt	1.3.6.1.4.1.164.3.2.3.2.7.2.1.6	INTEGER	read-write	This attribute indicates the internally (In Mux) connected/routed port.
INT prtExHs4TsIConSlot	1.3.6.1.4.1.164.3.2.3.2.7.2.1.5	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS).
I32 prtExHs4TsIConTs	1.3.6.1.4.1.164.3.2.3.2.7.2.1.7	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Module and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
I32 prtExHs4TsIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling.
INT prtExHs4TsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.3	INTEGER	read-only	This attribute indicates a unique port number. Hs4/T1 and Hs4/T1 cards have only one external interface.
INT prtExHs4TsSltIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExHsfBcastRingSrcPort	1.3.6.1.4.1.164.3.2.3.2.6.1.14	INTEGER	read-write	This object is applicable only when prtExHsfOperMode= bidirBcastRing. In this case, the values mean: - none - this port will be connected to ML in TSA as usual. - exPrt1.. exPrtX ; X=maximum ports of the card in focus : it means that the same TS that is assigned in TSA to this port is actually connected also to this port, for Broadcast Ring mode. Therefore, this port should NOT be connected to ML in TSA.
INT prtExHsfClkMode	1.3.6.1.4.1.164.3.2.3.2.6.1.6	INTEGER	read-write	This attribute indicates a unique port operation clock mode.
INT prtExHsfClkPolarity	1.3.6.1.4.1.164.3.2.3.2.6.1.12	INTEGER	read-write	This object indicates the clock polarity. For FCD-M this object will be applicable only for the fixed HS port (the fixed port on the device).
INT prtExHsfConnect	1.3.6.1.4.1.164.3.2.3.2.6.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExHsfControlSignal	1.3.6.1.4.1.164.3.2.3.2.6.1.13	INTEGER	read-write	This object indicates the Control Signal according to G.797 ITU-T standard. For FCD-M this object will be applicable for the fixed HS port (the fixed port on the device) and HS-Q/N channels. Local and End to End are applicable only when channel Interface type is RS-530, else it will be Not Applicable.
INT prtExHsfCts	1.3.6.1.4.1.164.3.2.3.2.6.1.7	INTEGER	read-write	This attribute indicates a unique CTS control line operation mode.
INT prtExHsfFifoSize	1.3.6.1.4.1.164.3.2.3.2.6.1.8	INTEGER	read-write	Size in bits.
INT prtExHsfInbandLoopback	1.3.6.1.4.1.164.3.2.3.2.6.1.11	INTEGER	read-write	This object indicates if Inband Loopback from the Network should be enabled or disabled.
INT prtExHsfLinkTo	1.3.6.1.4.1.164.3.2.3.2.6.1.9	INTEGER	read-write	This attribute indicates a slot of Main Link module, that the port is linked to. This object is the same for all the ports in the specific card because of HW limitations. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExHsfOperMode	1.3.6.1.4.1.164.3.2.3.2.6.1.10	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request. bidirBcastRing = Bidirectional Broadcast Ring. When this value is selected, AND RTS=On, the port opens its transmission channel.
INT prtExHsfRate	1.3.6.1.4.1.164.3.2.3.2.6.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtExHsiActType	1.3.6.1.4.1.164.3.2.3.2.8.1.1.8	INTEGER	read-write	It indicates the Activation Type. Activation Type is the Synchronization type towards the PBX. It is applicable only when prtExHsiInterface=nt. notApplicable - for cards that do not support this object, or when prtExHsiInterface is NOT nt.
prtExHsiCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.8.1.1		not-accessible	An entry in table.
I32 prtExHsiCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExHsiCnfgTable	1.3.6.1.4.1.164.3.2.3.2.8.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExHsiConnect	1.3.6.1.4.1.164.3.2.3.2.8.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. v51 - this port is connected to a V5.1 interface. All rest of the values will be 'notApplicable' in this case. V5 MIB will be used instead. v52 - this port is connected to a V5.2 interface. All rest of the values will be 'notApplicable' in this case. V5 MIB will be used instead.
INT prtExHsiInterface	1.3.6.1.4.1.164.3.2.3.2.8.1.1.7	INTEGER	read-write	It indicates the interface type: lt = line termination nt = network termination te = terminal equipment. lt1 - for ASMi-31 connection (not ISDN) For MP: For HS-U/I only 'lt' and 'nt' are applicable. For HS-U/1 only 'lt' is applicable. For HS-S , only 'te' and 'nt' are applicable. For HS-U, this object is not applicable. For HS-U6, HS-U12, are applicable: 'lt'=lt-i,'nt'=nt-i, lt1. For DXC: For HS-U8, HS-U16, are applicable: 'lt'=LT-I,'nt'=NT-I, 'lt1'=LT-1.
INT prtExHsiLinkTo	1.3.6.1.4.1.164.3.2.3.2.8.1.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the HS-? card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
I32 prtExHsiPrtIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.3	Integer32	read-only	A unique port identifier within the card. For MP : 1..12 For DXC: 111 .. 2531. See DXC R6 spec for port index convention. For FCD-A, 'S' Interface external ports: 131, 141, 151, 161.
INT prtExHsiRate	1.3.6.1.4.1.164.3.2.3.2.8.1.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtExHsiSltIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
INT prtExHsrClkMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.11	INTEGER	read-write	Clock mode. This object is applicable for Sync protocol only.
prtExHsrCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.10.1.1		not-accessible	An entry in table.
I32 prtExHsrCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExHsrCnfgTable	1.3.6.1.4.1.164.3.2.3.2.10.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExHsrConnect	1.3.6.1.4.1.164.3.2.3.2.10.1.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtExHsrCts	1.3.6.1.4.1.164.3.2.3.2.10.1.1.10	INTEGER	read-write	CTS. This object is applicable for Async protocol only.
INT prtExHsrDataBits	1.3.6.1.4.1.164.3.2.3.2.10.1.1.7	INTEGER	read-write	Data Bits. This object is applicable for Async protocol only.
INT prtExHsrDcdDsr	1.3.6.1.4.1.164.3.2.3.2.10.1.1.13	INTEGER	read-write	DCD & DSR.
INT prtExHsrEncapsMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.20	INTEGER	read-write	Low Speed encapsulation method over PCM. When Encapsulation mode is Latency optimized, only rates up to 19.2 are supported. In this case a double number of bits occupy the Time Slot. For up to 9.6 Kbps - 4 bits are occupied. For 14.4 & 19.2 Kbps - 8 bits are occupied. When Encapsulation Mode is Bandwidth Optimized: For up to 9.6 Kbps - 2 bits are occupied. For 14.4 & 19.2 Kbps - 4 bits are occupied. For higher rates - 8 bits are occupied.
INT prtExHsrLinkTo	1.3.6.1.4.1.164.3.2.3.2.10.1.1.12	INTEGER	read-write	It indicates the slot of the main link card to which the HS-R card is mapped. notApplicable - for HS-U/1 internal ports. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExHsrLlbEnable	1.3.6.1.4.1.164.3.2.3.2.10.1.1.16	INTEGER	read-write	Enable/Disable LLB.
INT prtExHsrOperMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.14	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request.
INT prtExHsrParity	1.3.6.1.4.1.164.3.2.3.2.10.1.1.8	INTEGER	read-write	- For HS-R card, this object indicates if the parity bit is needed or not. Therefore, the 'no' and 'yes; values are applicable. - For HS-S12, HS-U12, the parity type is selected: no, odd, even. This object is applicable for Async protocol only.
INT prtExHsrProtocol	1.3.6.1.4.1.164.3.2.3.2.10.1.1.5	INTEGER	read-write	This object indicates the protocol.
I32 prtExHsrPrtIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.3	Integer32	read-only	A unique prt identifier within the card. Valid values: For MP: - For HS-R cards: exPrt1 (1) .. exPrt4 (4) - For HS-U/1 cards: inPrt1 (101) .. inPrt4 (104) - For HS-S12, HS-S6, HS-U12, HS-U6 cards: exPrt1 (1) .. exPrt12 (12). This MIB table is used only for LT-1 interface. For DXC: - For HS-U8, HS-U16 cards: 111 .. 2531 (See DXC R6 spec for port index convention). This MIB table is used only for LT-1 interface.
INT prtExHsrRate	1.3.6.1.4.1.164.3.2.3.2.10.1.1.6	INTEGER	read-write	This object indicates the port speed. The 16,32,48,56,64 and 128 kbps rates are applicable only for Sync protocol. The 57.6 and 115.2 kbps rates are applicable only for Async protocol. notConnected= 0 rate.
INT prtExHsrRateAdapt	1.3.6.1.4.1.164.3.2.3.2.10.1.1.18	INTEGER	read-write	Rate Adaptation - takes a low rate and adapts it to 64Kbps. This object specifies the means this adaptation is done by.
INT prtExHsrRemoteModem	1.3.6.1.4.1.164.3.2.3.2.10.1.1.19	INTEGER	read-write	Remote modem. asmi31s2 = ASMi-31/2
INT prtExHsrRlbEnable	1.3.6.1.4.1.164.3.2.3.2.10.1.1.17	INTEGER	read-write	Enable/Disable RLB.
INT prtExHsrRtsDtr	1.3.6.1.4.1.164.3.2.3.2.10.1.1.15	INTEGER	read-write	RTS & DTR.
INT prtExHsrSltIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted.
INT prtExHsrStopBits	1.3.6.1.4.1.164.3.2.3.2.10.1.1.9	INTEGER	read-write	This object indicates the minimum number of stop bits in the tx async frame. This object is applicable for Async protocol only.
INT prtExLs2ClkMode	1.3.6.1.4.1.164.3.2.3.2.4.1.1.6	INTEGER	read-write	This attribute indicates a unique port operation clock mode.
prtExLs2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.4.1.1		not-accessible	An entry in table.
I32 prtExLs2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExLs2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.4.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExLs2Connect	1.3.6.1.4.1.164.3.2.3.2.4.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs2Cts	1.3.6.1.4.1.164.3.2.3.2.4.1.1.7	INTEGER	read-write	CTS.
INT prtExLs2Dcd	1.3.6.1.4.1.164.3.2.3.2.4.1.1.8	INTEGER	read-write	DCD.
I32 prtExLs2EnvIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.9	Integer32	read-write	Envelope Index. When prtInLs2EnvAssign=auto, the value is 0 (not applicable).
INT prtExLs2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.3	INTEGER	read-only	This attribute indicates a unique port index. For the Ls2/X.58 exPrt(7)..exPrt(10) are not valid.
INT prtExLs2Rate	1.3.6.1.4.1.164.3.2.3.2.4.1.1.5	INTEGER	read-write	Port rates.
INT prtExLs2SltIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtExLs6ClkMode	1.3.6.1.4.1.164.3.2.3.2.13.1.1.7	INTEGER	read-write	This attribute indicates a unique port operation clock mode. It is applicable for Sync protocol only .
prtExLs6CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.1.1		not-accessible	An entry in table.
I32 prtExLs6CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExLs6CnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExLs6Connect	1.3.6.1.4.1.164.3.2.3.2.13.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs6CtrlSignal	1.3.6.1.4.1.164.3.2.3.2.13.1.1.8	INTEGER	read-write	Control Signal.
INT prtExLs6Cts	1.3.6.1.4.1.164.3.2.3.2.13.1.1.10	INTEGER	read-write	This object indicates the CTS control line operation mode.
INT prtExLs6DataBits	1.3.6.1.4.1.164.3.2.3.2.13.1.1.9	INTEGER	read-write	Data Bits. This object is applicable for Async protocol only.
INT prtExLs6LinkToInternal	1.3.6.1.4.1.164.3.2.3.2.13.1.1.11	INTEGER	read-write	This object indicates which internal port of the card, the external port is linked to.
INT prtExLs6Protocol	1.3.6.1.4.1.164.3.2.3.2.13.1.1.5	INTEGER	read-write	This attribute indicates the protocol. async - can be selected only for ports 1-2.
INT prtExLs6PrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.3	INTEGER	read-only	This attribute indicates a unique port index.
INT prtExLs6Rate	1.3.6.1.4.1.164.3.2.3.2.13.1.1.6	INTEGER	read-write	Port rates in bps. g1 - contains the values : (2)-(6),(9),(12),(16) g2 - contains the values : (7),(10),(14),(19) g3 - contains the values : (8),(11),(13),(15),(17),(18),(20); it is not applicable when using Async protocol. Rates of pair ports (1-2, 3-4, 5-6) must be from the same group.
INT prtExLs6SltIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
prtExLs6VCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.2.1		not-accessible	An entry in table.
I32 prtExLs6VCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExLs6VCnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExLs6VConnect	1.3.6.1.4.1.164.3.2.3.2.13.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs6VEchoCanceler	1.3.6.1.4.1.164.3.2.3.2.13.2.1.6	INTEGER	read-write	Echo canceler activation.
INT prtExLs6VIfType	1.3.6.1.4.1.164.3.2.3.2.13.2.1.7	INTEGER	read-write	This attribute indicates the interface type of the port. w4wire - is applicable only for E&M port type.
INT prtExLs6VOos	1.3.6.1.4.1.164.3.2.3.2.13.2.1.10	INTEGER	read-write	Out of Service signaling mode.
INT prtExLs6VPrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExLs6VRate	1.3.6.1.4.1.164.3.2.3.2.13.2.1.5	INTEGER	read-write	Rate (bps) used for FAX transmission and Voice coding.
I32 prtExLs6VRxGain	1.3.6.1.4.1.164.3.2.3.2.13.2.1.9	Integer32	read-write	Receive gain in dBm. E&M - values range: -17 .. 2 FXO - values range: -17 .. -1 FXS - values range: -17 .. 2
INT prtExLs6VSltIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
I32 prtExLs6VTxGain	1.3.6.1.4.1.164.3.2.3.2.13.2.1.8	Integer32	read-write	Transmit gain in dBm. E&M - values range: -17 .. 8 FXO - values range: -16 .. 4 FXS - values range: -13 .. 8
prtExMbeCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.11.1.1		not-accessible	An entry in table.
I32 prtExMbeCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExMbeCnfgTable	1.3.6.1.4.1.164.3.2.3.2.11.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExMbeLan	1.3.6.1.4.1.164.3.2.3.2.11.1.1.4	INTEGER	read-write	This attribute indicates whether the MBE port is operated as main or remote bridge.
INT prtExMbePrtIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtExMbeSltIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtExPh1MlClkMode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.13	INTEGER	read-write	Defines the clock operation mode of the T1/E1 interface. Ports that are connected to the TDM Buses must be in nodalTiming(3) clock mode.
prtExPh1MlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.1.1		not-accessible	An entry in table.
I32 prtExPh1MlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExPh1MlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.1		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to prtExPh1MlCnfgIdx=1.
INT prtExPh1MlConnect	1.3.6.1.4.1.164.3.2.3.2.2.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the card considerations because it may indicate that the module has only one physical interface.
INT prtExPh1MlFdlType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.16	INTEGER	read-write	A unique number to identify the side of the FDL operation. Normal: 'response' for the user side and 'command' for the PTT side. Applicable only when working with ESF-T1 link
I32 prtExPh1MlFragmentSize	1.3.6.1.4.1.164.3.2.3.2.2.1.1.32	Integer32	read-write	This parameter indicates the maximum number of bytes permitted in a packet send over the Link. Exceeding this size will cause packet fragmentation.
I32 prtExPh1MlIdleCode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.11	Integer32	read-write	Determines the code for transmission in empty time slots. Type value(00-FFH), Excluding 0H,8H,10H,12H,21H,24H,42H,49H, 84H,92H
INT prtExPh1MlIfType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.24	INTEGER	read-write	Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values.
INT prtExPh1MlImpedance	1.3.6.1.4.1.164.3.2.3.2.2.1.1.27	INTEGER	read-write	The Line Impedance. For T1 (always balanced), impedance is 100 ohm. For E1: - balanced = 120 ohm - unbalanced = 75 ohm.
INT prtExPh1MlInbandMng	1.3.6.1.4.1.164.3.2.3.2.2.1.1.17	INTEGER	read-write	A unique number to identify an Inband management over the link.
INT prtExPh1MlInbandMngRate	1.3.6.1.4.1.164.3.2.3.2.2.1.1.18	INTEGER	read-write	A unique number to identify the rate of the Inband management (Kbps). E1 port - it is not applicable when prtExPh1MlInbandMng selected is off. T1 port - it is not applicable when prtExPh1MlInbandMng selected is off OR fdlOrTs0.
INT prtExPh1MlInbandMngRoutProt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.23	INTEGER	read-write	This attribute indicates the Inband Mng routing protocol of the port.
INT prtExPh1MlInternalSwitch	1.3.6.1.4.1.164.3.2.3.2.2.1.1.30	INTEGER	read-write	This parameter shows whether the data will be transferred from one port to the other port within the same group of 2 ports. The default value is: Enable. Disable value might be necessary for security implementations or for ring applications. For Vmux-2100 device this parameter is used on the Channelized Cards. Both ports in each group should have the same value for this parameter.
INT prtExPh1MlLineCode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.6	INTEGER	read-write	This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for MPH.1/T1 E1 line code parameters for MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExPh1MlLineLen	1.3.6.1.4.1.164.3.2.3.2.2.1.1.7	INTEGER	read-write	This attribute is the line length parameter used only for T1/DSU interfaces. lenXXXpXXXft = len-XXX-XXXft.
INT prtExPh1MlLineType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.5	INTEGER	read-write	This attribute is the line type parameter for T1/E1 interface. The user should select only the values which are relevant to the specific port: (2),(3), (8) - for T1 port (4)..(7), (9) - for E1 port. (101) framed - This value does not exist in standard MIB and is used for a non-standard E1 port that doesn't has real framer. Note: for old devices, g732unframed(8) was used as E1 Unframed. That was because at the time this value did not exist in the standard MIB (RFC-1406), so we added it in private MIB. Now that it was added to standard MIB, private MIB was updated as well. This parameter has the same values as dsx1LineType in DS1 MIB (RFC-3895). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7) g732unframed dsx1Unframed (8) --from RFC-3895 e1Unframed dsx1E1Unframed (9) --from RFC-3895
INT prtExPh1MlMfClkSrcPrt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.15	INTEGER	read-write	A unique number to identify a port position in the mux. It has no effect when the prtExPh1MlMfClkSrcSlt selected is Local. inPrt1 - for MTML-H/E1 cards.
INT prtExPh1MlMfClkSrcSlt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.14	INTEGER	read-write	This attribute indicates whether the port Tx multiframe is synchronized with Rx multiframe of another port and the slot position of that port. This operation is required in order to bypass signaling of PCM voice channels. Its value is always local(2) when the port isn't connected to any TDM bus. When it's value is local(2) there is no meaning to 'prtExPh1MlMfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPh1MlMultiplier	1.3.6.1.4.1.164.3.2.3.2.2.1.1.25	INTEGER	read-write	The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps.
INT prtExPh1MlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.3	INTEGER	read-only	This attribute indicates a unique port number. MP-2100/2200: MTML-1/E1 and MTML-1/T1 cards have only one external interface. inPrt1, inPrt2 - for MTML-H/2E1 and HSH cards. inPrt1..inPrt4 - for MTML-E2 and MSL-4 cards. exPrt2..exPrt4 - for MTML-4 cards and others exPrt1..exPrt8 - for ML-8 cards. inPrt1..inPrt8 - for MSL-8 and VF-30 card family. MP-104/204: only exPrt3 (3) is applicable. MP-4100: intPrt1...intPrt84 - for CLX cards. For other products' index see their specification.
INT prtExPh1MlQ50BwControl	1.3.6.1.4.1.164.3.2.3.2.2.1.1.28	INTEGER	read-write	This object enables configuration of Q.50 Bandwidth Control on the port. If the bandwidth exceeds a certain threshold it is possible to disable new calls in the PBX via Q.50 protocol. Q.50 supports only E1 ports with Line Types: E1-MF (G.732S), E1-CRC-MF(G.732SCRC ) It does not support T1 ports. Annex A - the basic type of Q.50 which focuses only on the bandwidth control. Can use one of the following pairs of signaling bits: A&B or C&D. Annex B - Expansion of Annex A which includes also call release messages and Maintenance Messages. Uses A&B bits only.
INT prtExPh1MlQ50SignalPair	1.3.6.1.4.1.164.3.2.3.2.2.1.1.29	INTEGER	read-write	Q.50 Signaling bits Pair that is currently in use: A&B bits or C&D bits. For Annex B it will always be: aAndB (2).
INT prtExPh1MlRedundPort	1.3.6.1.4.1.164.3.2.3.2.2.1.1.21	INTEGER	read-write	This object indicates the redundacy ML port, coupled with the current ML port (prtExPh1MlPrtIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. When value is not 'none', it should be mutual to the redundant ML port. inPrt1 - for MTML-H/E1 cards. inPrt1..inPrt4 - for MTML-E2 cards. exPrt2..exPrt4 - for MTML-4 cards.
I32 prtExPh1MlRedundRecTime	1.3.6.1.4.1.164.3.2.3.2.2.1.1.22	Integer32	read-write	Redundancy Recovery Time (sec). After switching the ML card to the current (prtExPh1MlSltIdx), the next ML switch can be performed only after a minimum time, indicated by this object.
INT prtExPh1MlRedundSlot	1.3.6.1.4.1.164.3.2.3.2.2.1.1.20	INTEGER	read-write	This object indicates the slot containing the redundacy ML card, coupled with the current ML (prtExPh1MlSltIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. In the ?004 Unit the entries io6(10)..io12(16) are not valid When value is not 'none', it should be mutual to the redundant ML slot.
INT prtExPh1MlRedundType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.19	INTEGER	read-write	This object determines the ML redundancy type: none - no ML redundacy dualCableAIS - each ML card is connected by a separate dualCableParallelTx cable to the other MUX (two cables connect two MUXes). There are two types of dual redundancy. yCable - Y cable is connected to both ML cards (one cable connects two MUXes). Default=none When only one ML card exists, the type can be only 'none'. The value should be the same for both ML slots.
INT prtExPh1MlRestoreTime	1.3.6.1.4.1.164.3.2.3.2.2.1.1.8	INTEGER	read-write	The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface.
INT prtExPh1MlRxSensitivity	1.3.6.1.4.1.164.3.2.3.2.2.1.1.10	INTEGER	read-write	This attribute is the rx line sensitivity parameter. low26dBm, high36dBm - applicable for T1-CSU shortHaul, longHaul - applicable for MTML-4 cards low15dbm was added for vmux110/210 T1 ports.
INT prtExPh1MlSigService	1.3.6.1.4.1.164.3.2.3.2.2.1.1.31	INTEGER	read-write	Signaling Service given by this link. notApplicable - for T1 links normal - usual Signaling advanced - V5 Signaling.
INT prtExPh1MlSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used.
I32 prtExPh1MlSupportedTS	1.3.6.1.4.1.164.3.2.3.2.2.1.1.26	Integer32	read-only	Number of Supported Time Slots by the agent. For Vmux-110 there is HW that supports less than 31/24 Time Slots for the E1/T1 port.
INT prtExPh1MlTdmTrunk	1.3.6.1.4.1.164.3.2.3.2.2.1.1.12	INTEGER	read-write	This attribute indicates whether the port is used to transfer TDM cards data and through which Bus.
I32 prtExPh1MlTsBundle	1.3.6.1.4.1.164.3.2.3.2.2.2.1.11	Integer32	read-write	The number of the bundle containing this Time Slot. If no bundle exists for this TS or the bundle number is irrelevant, the value will be 0.
INT prtExPh1MlTsByteReversal	1.3.6.1.4.1.164.3.2.3.2.2.2.1.16	INTEGER	read-write	Byte Reversal. This variable defines whether the LSB or MSB is transmitted first. no(2) - MSB is transmitted first yes(3) - LSB is transmitted first.
INT prtExPh1MlTsChRate	1.3.6.1.4.1.164.3.2.3.2.2.2.1.15	INTEGER	read-write	The Rate of the Signaling Channel. notApplicable(1) when TS Type is other than Signaling or Transparent
I32 prtExPh1MlTsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExPh1MlTsEntry	1.3.6.1.4.1.164.3.2.3.2.2.2.1		not-accessible	An entry in table.
OID prtExPh1MlTsExt	1.3.6.1.4.1.164.3.2.3.2.2.2.1.8	OBJECT IDENTIFIER	read-only	A pointer to an extension of this table: prtExTsSplitTable. - If prtExPh1MlTsIConSlot='split', its value should be set to the OBJECT IDENTIFIER of the prtExTsSplitTable, with its relevant CnfgIdx, SltIdx, PrtIdx, TsIdx and 1st TsBit. - If prtExPh1MlTsIConSlot is not 'split', its value should be set to the OBJECT IDENTIFIER { 0 0 }.
I32 prtExPh1MlTsIConPrt	1.3.6.1.4.1.164.3.2.3.2.2.2.1.6	Integer32	read-write	This attribute indicates the internally (In Mux) connected/routed port. For MP, the values will be: { exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , noConnect (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109) , inPrt10 (110) , inPrt11 (111) , inPrt12 (112) } For other products see specific values at spec.
INT prtExPh1MlTsIConSlot	1.3.6.1.4.1.164.3.2.3.2.2.2.1.5	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS).
I32 prtExPh1MlTsIConTs	1.3.6.1.4.1.164.3.2.3.2.2.2.1.7	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated to multiframe synchronization and voice signaling.
I32 prtExPh1MlTsIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
INT prtExPh1MlTsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.3	INTEGER	read-only	This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have only one external interface. exPrt2 - for ME1-2, MT1-2 and mhsPri cards. exPrt3, exPrt4 - for mhsPri cards. inPrt1 - for MTML-H/E1 cards.
INT prtExPh1MlTsSigProfile	1.3.6.1.4.1.164.3.2.3.2.2.2.1.17	INTEGER	read-write	This object indicates the Signaling Profile of the port. It is applicable only when prtMl4SigProfile=perTS. p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5
INT prtExPh1MlTsSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (255) is used.
I32 prtExPh1MlTsSubChMask	1.3.6.1.4.1.164.3.2.3.2.2.2.1.14	Integer32	read-write	The Sub-Channel Type Mask. This variable is relevant only when Time-Slot Type is SubCh (e.g. prtExPh1MlTsType = subCh1...subCh8).
INT prtExPh1MlTsSubChType	1.3.6.1.4.1.164.3.2.3.2.2.2.1.13	INTEGER	read-write	The Time Slot Sub-Channel Type. This variable is relevant only when Time-Slot Type is SubCh (e.g. prtExPh1MlTsType = subCh1...subCh8).
prtExPh1MlTsTable	1.3.6.1.4.1.164.3.2.3.2.2.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExPh1MlTsTest that will be written directly to the Active Configuration.
INT prtExPh1MlTsTest	1.3.6.1.4.1.164.3.2.3.2.2.2.1.9	INTEGER	read-write	This attribute indicates a test to be activated on the selected TS. It is applicable only when prtSTstCmd=testPerTS(31). notApplicable - when prtSTstCmd is NOT testPerTS(31). none - no test is applied for the selected TS. split - when the tests are per Bit of the selected TS.
I32 prtExPh1MlTsTestDuration	1.3.6.1.4.1.164.3.2.3.2.2.2.1.12	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific TS. This entry applies to all the test operations. For the Vmux2100 the values are: 0 - 60 seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtExPh1MlTsTest' parameter.
INT prtExPh1MlTsType	1.3.6.1.4.1.164.3.2.3.2.2.2.1.10	INTEGER	read-write	The Time Slot Type. Transparent - means that the Time Slot will be Rx/Tx as is without processing it. If the device requires more than 1 unique data or ss7 Time Slot, options with numbers can be used like: data...data4. Each numbered Type can go to a different destination. ss7n2 - means the 2nd group of ss7 Time Slots. data2,data3, data4 mean group 2,3,4 of Data Time Slots. subCh1...subCh8 mean Sub Channel 1...8, respectively. trau, qmux, dynamic, signaling - are used by GSM devices.
INT prtExPh1MlTxGain	1.3.6.1.4.1.164.3.2.3.2.2.1.1.9	INTEGER	read-write	This attribute is the tx gain parameter used only for T1/CSU interfaces.
INT prtExPhPlCcittCrc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.32	INTEGER	read-write	This object indicates how many Bits are used for CRC (HDLC item).
INT prtExPhPlClkMode	1.3.6.1.4.1.164.3.2.3.2.3.1.1.9	INTEGER	read-write	Clock mode.
INT prtExPhPlCllmMsg	1.3.6.1.4.1.164.3.2.3.2.3.1.1.28	INTEGER	read-write	This object is CLLM Message (if required or not). It determines whether to send (or not) a congestion message when the port is Rx congested. Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlClockEncoding	1.3.6.1.4.1.164.3.2.3.2.3.1.1.30	INTEGER	read-write	This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols. For MAXCESS 3000 & MP2100H: when setting to nrzI (3) the nrzI works as nrzI Mark. For MAXCESS 30/300 when setting to nrzI (3) the nrzI works as nrzI Space.
prtExPhPlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.3.1.1		not-accessible	An entry in table.
I32 prtExPhPlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExPhPlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.3.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
I32 prtExPhPlCongLevel	1.3.6.1.4.1.164.3.2.3.2.3.1.1.12	Integer32	read-write	This attribute indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5 percent.
INT prtExPhPlCongResponse	1.3.6.1.4.1.164.3.2.3.2.3.1.1.11	INTEGER	read-write	This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/received becn to/from the network). no - do nothing flowControl - translates the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done on both directions. toFlowControl- translates the backward congestion indication received from the internal connection port (normally the network side) to flow control and do nothing in the other direction.
INT prtExPhPlConnect	1.3.6.1.4.1.164.3.2.3.2.3.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExPhPlConnectionTyp	1.3.6.1.4.1.164.3.2.3.2.3.1.1.8	INTEGER	read-write	This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management opration (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetMotMana - indicates network internal line, but the remote mux is not managed by the NMS. User - User to Network Interface. OtherNet - Network To Network Interface. PubNet - Access Mux To PubNet Interface.
INT prtExPhPlDataBits	1.3.6.1.4.1.164.3.2.3.2.3.1.1.17	INTEGER	read-write	This attribute indicates the number of data bits in async frame. It is relevant only for Async protocols.
INT prtExPhPlDcdRts	1.3.6.1.4.1.164.3.2.3.2.3.1.1.15	INTEGER	read-write	Protocol may require end to end connect indication over the network. End to end link connection establishment over the FR network will be indicated to the user by using DCD or RTS control signals, depending on the clock mode: DCE or DTE respectively. The options are : - On : DCD(DCE)/RTS(DTE) will be constantly ON no matter if the End to End connection is established or not. - End to End: The DCD(DCE)/RTS(DTE) will be according to the status of the End to End connection.
INT prtExPhPlDcdRtsControlPath	1.3.6.1.4.1.164.3.2.3.2.3.1.1.16	INTEGER	read-write	Protocol may require end to end connect indication over the network. This parameter defines whether to take the user connection status (RTS(DCE)/DCD(DTE)) and forward it to the network side. - on : Transmit active connection to the network regardless the RTS/DCD control lines status. - off: Transmit active connection to the network according to the status of the RTS/DCD pin.
INT prtExPhPlDceClkSrc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.10	INTEGER	read-write	This attribute indicates the source of the clock when working in dce or ext-dce clock mode. notApplicable(1) - is applied for dte(3) and lbt(5) clock modes. When clock mode is dte, the clock source is always external, therefore this object's value is notApplicable. local(2) and nodalTiming(3) - are valid in dce(1), extDce(2) or int(4) clock modes. The recommended clock source is local(2).
I32 prtExPhPlDlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExPhPlDlciEntry	1.3.6.1.4.1.164.3.2.3.2.3.2.1		not-accessible	An entry in table.
I32 prtExPhPlDlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.3.2.1.8	Integer32	read-write	This attribute indicates a unique internal connection dlci number, the dlci is routed to.
INT prtExPhPlDlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.3.2.1.7	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to. clNMS - will be used for NMS SNMP messages. It can be any port of the CL card. This value will be selectable only if prtExPhPlDlciIConSlt='cl' or 'notApplicable'.
INT prtExPhPlDlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.3.2.1.6	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. cl - will represent any of the CL slots. This value can be selected for multiple DLCIs of the product. In the ?004 Unit the entries io6(10)..io16) are not valid
I32 prtExPhPlDlciIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, its type is 'user' and the only valid index is 1.
I32 prtExPhPlDlciPriority	1.3.6.1.4.1.164.3.2.3.2.3.2.1.13	Integer32	read-write	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority.
INT prtExPhPlDlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. PH.1/E1 and PH.1/T1 cards have three internal ports. Stand-alone units may have six such ports.
INT prtExPhPlDlciRxBc	1.3.6.1.4.1.164.3.2.3.2.3.2.1.11	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line).
INT prtExPhPlDlciRxBe	1.3.6.1.4.1.164.3.2.3.2.3.2.1.12	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line).
INT prtExPhPlDlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPhPlDlciStatus	1.3.6.1.4.1.164.3.2.3.2.3.2.1.14	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
prtExPhPlDlciTable	1.3.6.1.4.1.164.3.2.3.2.3.2		not-accessible	The write operation into the Table Objects is valid only at the TmpCnfg entry.
INT prtExPhPlDlciTxBc	1.3.6.1.4.1.164.3.2.3.2.3.2.1.9	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line).
INT prtExPhPlDlciTxBe	1.3.6.1.4.1.164.3.2.3.2.3.2.1.10	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line).
INT prtExPhPlDlciValid	1.3.6.1.4.1.164.3.2.3.2.3.2.1.5	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
I32 prtExPhPlEnqPeriod	1.3.6.1.4.1.164.3.2.3.2.3.1.1.23	Integer32	read-write	This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlErrorsThreshold	1.3.6.1.4.1.164.3.2.3.2.3.1.1.26	Integer32	read-write	This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlFlowControl	1.3.6.1.4.1.164.3.2.3.2.3.1.1.14	INTEGER	read-write	This attribute indicates the required flow control betweeen the port and the remote equipment. fecnBecn - is valid only for FR, FR+ and CR protocols. xonXoff,dtrCts - are valid only for Async protocols. speedReduction - is valid only for DLC protocol when the Clock Mode is DCE and the Clock Source is Local.
INT prtExPhPlFrameSeparator	1.3.6.1.4.1.164.3.2.3.2.3.1.1.33	INTEGER	read-write	This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line.
INT prtExPhPlFrMngProt	1.3.6.1.4.1.164.3.2.3.2.3.1.1.22	INTEGER	read-write	This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtExPhPlConnectionTyp = sameNetManaged, this object will be RO (internally determined).
I32 prtExPhPlFrWindowSize	1.3.6.1.4.1.164.3.2.3.2.3.1.1.25	Integer32	read-write	This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlFullRptPeriod	1.3.6.1.4.1.164.3.2.3.2.3.1.1.24	Integer32	read-write	This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlHRate	1.3.6.1.4.1.164.3.2.3.2.3.1.1.5	INTEGER	read-write	This attribute indicates the port speed for HIGH speed cards. The card has limitations about the maximum sigma channel speeds and about the possible rates for each clock mode . N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. 'r9d6KbpsNLE' means rate of 9.6 Kbps ('d'=dot). Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r2048KbpsE (63), -- r2048KbpsNLE
I32 prtExPhPlIdleCode	1.3.6.1.4.1.164.3.2.3.2.3.1.1.34	Integer32	read-write	Determines the code for transmission when there are no frames to transmit on the line. The value should be 0 to FFH.
I32 prtExPhPlJitter	1.3.6.1.4.1.164.3.2.3.2.3.1.1.35	Integer32	read-write	Maximum variant delay of the FR network, in msec.
INT prtExPhPlLRate	1.3.6.1.4.1.164.3.2.3.2.3.1.1.6	INTEGER	read-write	This attribute indicates the port speed for LOW speed cards. The card has limitations about the possible rates for each clock mode. N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r57600bpsLE (16), -- r57600bpsNLE
I32 prtExPhPlLXoff	1.3.6.1.4.1.164.3.2.3.2.3.1.1.21	Integer32	read-write	This attribute indicates the character used as X-Off to notify receive disable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable
I32 prtExPhPlLXon	1.3.6.1.4.1.164.3.2.3.2.3.1.1.20	Integer32	read-write	This attribute indicates the character used as X-On to notify receive enable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable
I32 prtExPhPlMinSeparators	1.3.6.1.4.1.164.3.2.3.2.3.1.1.31	Integer32	read-write	Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable
INT prtExPhPlModemActivate	1.3.6.1.4.1.164.3.2.3.2.3.3.1.5	INTEGER	read-write	This object indicates whether the Dial Up Modem is activated when the first frame is received or it is always activated. Default: onFirstFrame
I32 prtExPhPlModemCallDelay	1.3.6.1.4.1.164.3.2.3.2.3.3.1.8	Integer32	read-write	Time in Seconds that the device will wait before dialing to the remote device. This feature is mostly used when there is a backup modem to the main link and the main link is down. In this case it is important to prevent the 2 devices from dialing through the backup modems to each other at the same time. It is advised to configure one side with a small call delay and the other side with a large call delay. Legal Values are: 0 - 30, 60, 120, 180, 240, 300, 600, 900, 1200, 1500, 1800 . 65535 sec. means that this parameter is not applicable. Default: 0 sec
I32 prtExPhPlModemCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExPhPlModemEntry	1.3.6.1.4.1.164.3.2.3.2.3.3.1		not-accessible	An entry in table.
I32 prtExPhPlModemMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.3.3.1.6	Integer32	read-write	Max Time allowed in Seconds without any traffic before the line is disconnected. Legal Values are: 1 sec, 2 sec .. 5 sec, 10 sec, 20 sec.. 1 min, 2 min .. 10 min, 15 min, 20 min, 25 min, 30 min. 65535 sec. means that this parameter is not applicable. Default: 1 sec.
INT prtExPhPlModemPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.3	INTEGER	read-only	This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid.
INT prtExPhPlModemSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtExPhPlModemStatus	1.3.6.1.4.1.164.3.2.3.2.3.3.1.4	INTEGER	read-write	This object indicates whether a Dial Up Modem is enabled on this port. Default: disable For Vmux devices this object shows whether there is Modem Relay support.
prtExPhPlModemTable	1.3.6.1.4.1.164.3.2.3.2.3.3		not-accessible	External Modem Parameters. The write operation into the Table Objects is valid only for the TmpCnfg entry.
I32 prtExPhPlModemTimeBtwnCalls	1.3.6.1.4.1.164.3.2.3.2.3.3.1.7	Integer32	read-write	Minimum Time in Seconds which is required after a call was disconnected. In this time no other call will be initiated from this Modem port even if there were frames transmitted to this port. This time is required for some Modems which have initializations that take a few seconds. Legal Values are: 0 sec. - 30 sec., 1-5 min. 65535 sec. means that this parameter is not applicable. Default: 0 sec
INT prtExPhPlParity	1.3.6.1.4.1.164.3.2.3.2.3.1.1.18	INTEGER	read-write	This attribute indicates the parity operation mode in async frame. It is relevant only for Async protocols.
INT prtExPhPlProtDelayLevel	1.3.6.1.4.1.164.3.2.3.2.3.1.1.29	INTEGER	read-write	This object is the Segmentation in Bytes. In some cases, the enumerated values will mean other segmentation values than specified: Product: MX-3000 MX-3000 MX-300/MX-30 Protocol: FR+ Transparent FR+ ----------------------------------------------------- level 1 50 Bytes 44 Bytes 50 Bytes level 2 158 Bytes 155 Bytes 158 Bytes level 3 266 Bytes 266 Bytes 266 Bytes level 4 376 Bytes 377 Bytes 376 Bytes level 5 484 Bytes 488 Bytes 484 Bytes Defval=level 1 value This parameter is applicable only for FR+ and transparent protocols.
INT prtExPhPlProtocol	1.3.6.1.4.1.164.3.2.3.2.3.1.1.7	INTEGER	read-write	This object indicates the applied protocol.
INT prtExPhPlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.3	INTEGER	read-only	This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid.
INT prtExPhPlPvcCreateMsg	1.3.6.1.4.1.164.3.2.3.2.3.1.1.27	INTEGER	read-write	This object is Update Message (if required or not). It determines whether a message of a New PVC Creation is requested or not (yes/no). Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtExPhPlStopBits	1.3.6.1.4.1.164.3.2.3.2.3.1.1.19	INTEGER	read-write	This attribute indicates the minimum number of stop bits in the tx async frame. It is relevant only for Async protocols.
INT prtExPhPlTc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.13	INTEGER	read-write	This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports of a specific card .
INT prtExPVc4AutoFaxMode	1.3.6.1.4.1.164.3.2.3.2.9.1.1.21	INTEGER	read-write	This object indicates if the system will switch automatically to FAX mode when detecting FAX activity. Default=Yes.
I32 prtExPVc4ChannelId	1.3.6.1.4.1.164.3.2.3.2.9.1.1.31	Integer32	read-write	Channel Identifier. According to FRF11 each voice port that works as force connect should add a CH Id after the DLCI in the frame header. Default : 1 Applicable only for Force Connect. Not Applicable value will be 0.
prtExPVc4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.9.1.1		not-accessible	An entry in table.
I32 prtExPVc4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExPVc4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.9.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExPVc4CoderAndRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.33	INTEGER	read-write	Coder and Rate for the Voice Compression. In MPH: Relevant for MVC-8 card only.
INT prtExPVc4CodingLaw	1.3.6.1.4.1.164.3.2.3.2.9.1.1.29	INTEGER	read-write	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations
I32 prtExPVc4CongLevel	1.3.6.1.4.1.164.3.2.3.2.9.1.1.14	Integer32	read-write	This object indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5%.
INT prtExPVc4Connect	1.3.6.1.4.1.164.3.2.3.2.9.1.1.5	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
IP prtExPVc4DefaultGateway	1.3.6.1.4.1.164.3.2.3.2.9.1.1.51	IpAddress	read-write	This object defines the Default Gateway for this interface.
I32 prtExPVc4DelayStart	1.3.6.1.4.1.164.3.2.3.2.9.1.1.25	Integer32	read-write	This parameter is used only for Delay Protocol. This is the time that the calling party will wait after sending an Off hook signal and before sending DTMF digits to the called party. The delay values are 100..5000 msec in intervals of 100 msec.
I32 prtExPVc4DestBundle	1.3.6.1.4.1.164.3.2.3.2.9.1.1.48	Integer32	read-write	This object defines the destination Bundle at the far-end device.
STR prtExPVc4DestinationNum	1.3.6.1.4.1.164.3.2.3.2.9.1.1.34	DisplayString	read-write	The destination phone number: 0 to 22 digits. Applicable for Auto Dial - ipForceConnect(6), Permanent Dial and Auto Accept Extension Types. Default: Null String
IP prtExPVc4DestIp	1.3.6.1.4.1.164.3.2.3.2.9.1.1.47	IpAddress	read-write	This object defines the destination IP Address.
I32 prtExPVc4DiscOnSilence	1.3.6.1.4.1.164.3.2.3.2.9.1.1.36	Integer32	read-write	No. of silenced seconds after which the call will be disconected. A value of 0 means that there will be no disconnect when there is silence. Possible values: 0 - 900 sec.
I32 prtExPVc4DlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExPVc4DlciEntry	1.3.6.1.4.1.164.3.2.3.2.9.2.1		not-accessible	An entry in table.
I32 prtExPVc4DlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.9.2.1.7	Integer32	read-write	This attribute indicates a unique internal connection dlci number, the dlci is routed to.
INT prtExPVc4DlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.9.2.1.6	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to.
INT prtExPVc4DlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.9.2.1.5	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid
I32 prtExPVc4DlciPriority	1.3.6.1.4.1.164.3.2.3.2.9.2.1.12	Integer32	read-write	This attribute indicates a unique priority of the pvc. 6 is the lowest priority and 8 is the highest priority.
INT prtExPVc4DlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. VC4 cards have four external ports.
INT prtExPVc4DlciRxBc	1.3.6.1.4.1.164.3.2.3.2.9.2.1.10	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line).
INT prtExPVc4DlciRxBe	1.3.6.1.4.1.164.3.2.3.2.9.2.1.11	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line).
INT prtExPVc4DlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPVc4DlciStatus	1.3.6.1.4.1.164.3.2.3.2.9.2.1.13	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
prtExPVc4DlciTable	1.3.6.1.4.1.164.3.2.3.2.9.2		not-accessible	The write operation into the Table Objects is valid only at the TmpCnfg entry.
INT prtExPVc4DlciTxBc	1.3.6.1.4.1.164.3.2.3.2.9.2.1.8	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line).
INT prtExPVc4DlciTxBe	1.3.6.1.4.1.164.3.2.3.2.9.2.1.9	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line).
INT prtExPVc4DlciValid	1.3.6.1.4.1.164.3.2.3.2.9.2.1.4	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
INT prtExPVc4DtmfRelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.35	INTEGER	read-write	When DTMF RELAY is disabled, the DTMF digits (dialed by the user) are transmitted as compressed voice and in the remote unit are decompressed. When DTMF RELAY is enabled, the DTMF digits are detected at the near side and not transmitted as voice. Instead, only an indication of what digits were dialed are transmitted and in the far end the tone is regenerated.
INT prtExPVc4DynamicJitter	1.3.6.1.4.1.164.3.2.3.2.9.1.1.37	INTEGER	read-write	The MVC8 uses two mechanisms to overcome the network delay. The first one is a static jitter buffer which holds a constant buffer of up to 300 Msec and can be controled by the JITTER parameter (prtExPVc4VarDelay). The second one is the dynamic jitter which calculates, in real time, the network delay and handles a jitter buffer dynamically. The dynamic mechanism that is implemented in MVC8, was intended to overcome network delay yet when the network bursts, the MVC8 dynamic mechanism is not able to overcome the delay. Therefore it is better not to use the dynamic jitter (DISABLE - should be the default) where bursts may occur often.
INT prtExPVc4EandMType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.38	INTEGER	read-write	This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters.
INT prtExPVc4EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.9.1.1.12	INTEGER	read-write	Echo canceler activation.
STR prtExPVc4ExtensionNumber	1.3.6.1.4.1.164.3.2.3.2.9.1.1.17	DisplayString	read-write	This is the extension number of this port. This field is relevant only when the extension type is voice switching and is read only if the port is member of a hunt group.
INT prtExPVc4ExtensionType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.16	INTEGER	read-write	This object indicates the type of extension relevant for this port. ipForceConnect (6) is used for automatic connection or automatic dialing when the phone is off hook (hot line). permanentDial (7) means that the call is established upon power up. The hook may be on or off. Permanent Dialing can be used when there is no signaling. autoAccept (8) means that the called party in the Permanent Dialing will accept the call from the remote side automatically upon on or off hook.
INT prtExPVc4FaxRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.22	INTEGER	read-write	FAX initial rate. Default=9600 bps.
I32 prtExPVc4FrameSize	1.3.6.1.4.1.164.3.2.3.2.9.1.1.40	Integer32	read-write	Defines the maximum size in Bytes of the multiplexed frame. In some cases this must be limited to avoid IP fragmentation, which makes the multiplexing useless, and can also decrease the damage in case of frame loss. Valid range: 100..1461. notApplicable=0.
INT prtExPVc4GenerateRingBack	1.3.6.1.4.1.164.3.2.3.2.9.1.1.30	INTEGER	read-write	Determines whether the Ring Back tone is generated locally or from the remote end. The default is - NO (Meaning coming from the remote end). Yes means that the Ring Back Tone is generated locally. Applicable only for Force Connect.
INT prtExPVc4GenerateTone	1.3.6.1.4.1.164.3.2.3.2.9.1.1.28	INTEGER	read-write	This parameter indicates whether the device (MX or MPH) should generate dial tones for the channel. If the value is yes (3), it generates dial tones. If the value is no (2), the connected equipment will generate dial tones. For example for some ISDN sets the dial tone is generated by the phone itself while for others sets it is generated by the MX.
I32 prtExPVc4HuntGroupIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.20	Integer32	read-write	If it belongs to an hunt group, this fields indicates the index of the relevant hunt group. 0 = notApplicable
INT prtExPVc4HuntGroupMb	1.3.6.1.4.1.164.3.2.3.2.9.1.1.19	INTEGER	read-write	This object indicates if this port belongs to an hunt group.
INT prtExPVc4IfType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.6	INTEGER	read-write	This attribute indicates the interface type of the port. eAndM4wires and eAndM2wires - are valid only for E&M port type eAndM4wires - means 2/4 wires fxoGnd and fxoLoop - are valid only for FXO port type fxsGnd and fxsLoop - are valid only for FXS port type e1Framer, e1Slave, t1Framer, t1Slave - are applicable for the mvc4Pbx cards only.
INT prtExPVc4MaxRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.9	INTEGER	read-write	Voice rate.
I32 prtExPVc4MinPowerLevel	1.3.6.1.4.1.164.3.2.3.2.9.1.1.45	Integer32	read-write	Defines the minimum Power Level in dBm. Valid values: -1..-35 dBm.
I32 prtExPVc4MinPulseWidth	1.3.6.1.4.1.164.3.2.3.2.9.1.1.44	Integer32	read-write	Defines the minimum Pulse Width in msec. Valid values: 45-100 msec. notApplicable=0.
INT prtExPVc4MultiFreqRelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.43	INTEGER	read-write	This object enables/disables Multi Frequency Signaling Detection.
I32 prtExPVc4MultiplexInterval	1.3.6.1.4.1.164.3.2.3.2.9.1.1.41	Integer32	read-write	Defines the maximum amout of time (msec.) between multiplexed frames that are sent. For Vmux-400/420 devices: It defines the Payload Packetizing Interval. Valid values: 10-90 msec. notApplicable=0.
INT prtExPVc4Oos	1.3.6.1.4.1.164.3.2.3.2.9.1.1.11	INTEGER	read-write	Handling type, when connection is lost.
INT prtExPVc4OutPulsing	1.3.6.1.4.1.164.3.2.3.2.9.1.1.18	INTEGER	read-write	This field indicates whether to outpulse the received digits. It is notApplicable(1) when the extension type is forceConnect(2).
INT prtExPVc4PortConnection	1.3.6.1.4.1.164.3.2.3.2.9.1.1.32	INTEGER	read-write	Port connection determines whether the port is connected to a PABX (Trunk) or to Telephone set (Line) . It determines whether to send certain messages to the port or not. If the type is LINE then the port generates a ring back tone , if TRUNK it doesn't (The PBX does it).
INT prtExPVc4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.3	INTEGER	read-only	This object indicates the port number in the selected card (slot).
INT prtExPVc4PrtType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.4	INTEGER	read-write	This object indicates the type of the selected port. In Mx 30/300 phase 4: s0 & u are for Voice over ISDN. In MX 30/300 phase 5: sQsig & uQsig are used for Voice over ISDN with Qsig option. In MX MVC4 voice cards, each pair of ports 1-2, 3-4 may have a different type: E&M, FXO, FXS. In MVC4 compressed voice cards ports 1..4 have the same interface for all ports. In MVC8 compressed voice cards each group of ports 1..4, 5..8 may have a different type: E&M, FXO, FXS.
I32 prtExPVc4Rate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.39	Integer32	read-write	This is the Rate of the port in TS units. It is used by VF-30 card family. 0 = NA = port is not intended to be connected; therefore, no Rate.
I32 prtExPVc4RxGain	1.3.6.1.4.1.164.3.2.3.2.9.1.1.8	Integer32	read-write	Reception gain in dBm.
INT prtExPVc4SeizeAck	1.3.6.1.4.1.164.3.2.3.2.9.1.1.23	INTEGER	read-write	This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Example: If Seize Ack Parameter = YES, when the MVC.4 receives a seize signal (Off Hook) from the PBX it will send an Off Hook to the PBX. The Seize Parameter is relevant for all the following cards: MVC-4 MVC-4/E1-Framer MVC-4/T1-DSU-Framer MVC-4/T1-CSU-Framer MVC-4/E1-SLAVE MVC-4/T1-SLAVE Default values: Analog FXS - No (value can't be changed). Analog FXO - Yes (value can't be changed). Analog E&M - No (values NO/YES). Digital E1/T1 Framer & Slave - No.
INT prtExPVc4SignalingProtocol	1.3.6.1.4.1.164.3.2.3.2.9.1.1.24	INTEGER	read-write	The signaling protocol that will be used between the PABX & the voice port. Delay Start Protocol: the line is seized by sending an Off hook signal and after a delay, if the called party is available (On hook) DTMF (Dual Tone Multi Frequency) digits are sent towards the called party. Immediate Start Protocol: the line is seized by sending an Off Hook signal and immediately DTMF digits are sent towards the called party. Wink start protocol: the line is seized by sending an Off Hook signal and then the called party sends a short Off Hook wink signal. Now the calling party starts sending DTMF digits.
U32 prtExPVc4SigPacketInterval	1.3.6.1.4.1.164.3.2.3.2.9.1.1.52	Unsigned32	read-write	Defines the Signaling Packetizing Interval, which is the maximum time interval, measured in msec (milliseconds), between multiplexed signaling frames.
INT prtExPVc4SltIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
IP prtExPVc4SrcIpAddress	1.3.6.1.4.1.164.3.2.3.2.9.1.1.49	IpAddress	read-write	This object defines the Source IP Address.
IP prtExPVc4SrcIpMask	1.3.6.1.4.1.164.3.2.3.2.9.1.1.50	IpAddress	read-write	This object defines the Source IP Mask.
INT prtExPVc4SuperTandem	1.3.6.1.4.1.164.3.2.3.2.9.1.1.46	INTEGER	read-write	The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem, when enabled, allows transmission of compressed voice between a few devices and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay.
INT prtExPVc4Tc	1.3.6.1.4.1.164.3.2.3.2.9.1.1.10	INTEGER	read-write	Time interval for CIR control, in seconds. The value will be the same for all cards' ports.
INT prtExPVc4TransportProtocol	1.3.6.1.4.1.164.3.2.3.2.9.1.1.42	INTEGER	read-write	Transport Protocol. ptp = point to point. aal2oMpls = AAL2 over MPLS.
I32 prtExPVc4TxGain	1.3.6.1.4.1.164.3.2.3.2.9.1.1.7	Integer32	read-write	Transmission gain in dB.
I32 prtExPVc4VarDelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.13	Integer32	read-write	Maximum variant delay of the FR network, in msec.
I32 prtExPVc4WinkMaxDuration	1.3.6.1.4.1.164.3.2.3.2.9.1.1.27	Integer32	read-write	This parameter is used only for Wink Protocol. Max Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec.
I32 prtExPVc4WinkMinDuration	1.3.6.1.4.1.164.3.2.3.2.9.1.1.26	Integer32	read-write	This parameter is used only for Wink Protocol. Min Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec.
INT prtExPVc4Wire	1.3.6.1.4.1.164.3.2.3.2.9.1.1.15	INTEGER	read-write	This object indicates the wiring of the E&M port. It is applicable only for E&M card type.
prtExTreCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.12.1.1		not-accessible	An entry in table.
I32 prtExTreCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExTreCnfgTable	1.3.6.1.4.1.164.3.2.3.2.12.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExTreLan	1.3.6.1.4.1.164.3.2.3.2.12.1.1.4	INTEGER	read-write	This attribute indicates whether the TRE port is operated as main or remote bridge. Default=remote.
INT prtExTreLanRate	1.3.6.1.4.1.164.3.2.3.2.12.1.1.5	INTEGER	read-write	This attribute indicates the Rate of the TRE port in Mbit/sec. Default-r4M.
INT prtExTrePrtIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtExTreSltIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
I32 prtExTsBit	1.3.6.1.4.1.164.3.1.4.2.1.1.5	Integer32	read-only	This attribute indicates a unique Bit within the time slot. The valid Bits are: 1..8. 255=NA.
INT prtExTsBitTest	1.3.6.1.4.1.164.3.1.4.2.1.1.8	INTEGER	read-write	This attribute indicates a test to be activated on the selected Bit. It is applicable only when prtExPh1MlTsTest=split(254). none - no test is applied for the selected Bit. notApplicable - when prtExPh1MlTsTest is NOT split(254).
I32 prtExTsCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExTsIConPrt	1.3.6.1.4.1.164.3.1.4.2.1.1.7	Integer32	read-write	This attribute indicates the internally (In Mux) connected/routed port. For other products' index see their specification.
INT prtExTsIConSlot	1.3.6.1.4.1.164.3.1.4.2.1.1.6	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units.
I32 prtExTsIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling.
I32 prtExTsPrtIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.3	Integer32	read-only	This attribute indicates a unique port number. Most ML cards have only one external interface. inPrt1 - for MTML-H/E1 cards. For other products' index see their specification.
OCT prtExTsRxIoSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.12	OCTET STRING	read-only	IO - Rx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is received from IO port for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExTsRxSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.10	OCTET STRING	read-only	Link - Rx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is received from Link for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
INT prtExTsSltIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units.
prtExTsSplitEntry	1.3.6.1.4.1.164.3.1.4.2.1.1		not-accessible	An entry in table.
prtExTsSplitTable	1.3.6.1.4.1.164.3.1.4.2.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExTsBitTest that will be written directly to the Active Configuration.
OCT prtExTsTxIoSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.11	OCTET STRING	read-only	IO - Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is sent to IO port for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExTsTxSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.9	OCTET STRING	read-only	Link - Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is sent to Link for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
INT prtExVc2BusProtectionPoint	1.3.6.1.4.1.164.3.2.3.2.5.1.39	INTEGER	read-write	This object defines if the port is Bus Protection Point or not. notApplicable - when prtExVc2DspMode=pointToPoint. When we have a chain of devices where the edge devices ports are the Bus Protection Point, user must configure one of these ports as 'first' and the other as 'last'. It does not matter which one, it just matters that they will be different.
INT prtExVc2CallEnable	1.3.6.1.4.1.164.3.2.3.2.5.1.14	INTEGER	read-write	This object indicates the Enabled Call direction. notApplicable - for all cards except VC-2/R2. both - incoming + outgoing.
INT prtExVc2CallerIdEnable	1.3.6.1.4.1.164.3.2.3.2.5.1.33	INTEGER	read-write	This object Enables/Disables Receiving the Caller Id number from the remote side, for this port/channel.
INT prtExVc2CasStd	1.3.6.1.4.1.164.3.2.3.2.5.1.16	INTEGER	read-write	This object indicates the CAS (Channel Associated Signaling) Standard. notApplicable - for all cards except VC-2/R2.
INT prtExVc2CodingLaw	1.3.6.1.4.1.164.3.2.3.2.5.1.8	INTEGER	read-write	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations
INT prtExVc2CompressMethod	1.3.6.1.4.1.164.3.2.3.2.5.1.34	INTEGER	read-write	This object is applicable only when prtExVc2Encoding=adpcm. It defines which method is used for Compression. g726 - for 4 bits (the standard method). g726 - for 3 bits. It is especially needed for T1 applications with signaling.
INT prtExVc2Connect	1.3.6.1.4.1.164.3.2.3.2.5.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExVc2ConvTime	1.3.6.1.4.1.164.3.2.3.2.5.1.27	INTEGER	read-write	Conversation Time in minutes. Applicable for VC-6A/4LB card.
INT prtExVc2EandMType	1.3.6.1.4.1.164.3.2.3.2.5.1.25	INTEGER	read-write	This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters.
INT prtExVc2EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.5.1.17	INTEGER	read-write	Echo canceler activation. notApplicable - for VC-2 and VC-6 cards.
INT prtExVc2EchoCancelerModule	1.3.6.1.4.1.164.3.2.3.2.5.1.29	INTEGER	read-only	This parameter indicates whether Echo canceler module exists for this port.
INT prtExVc2Encoding	1.3.6.1.4.1.164.3.2.3.2.5.1.19	INTEGER	read-write	Voice Encoding Mode. linear - is relevant only for the ports of VC-16A card.
INT prtExVc2IfSignaling	1.3.6.1.4.1.164.3.2.3.2.5.1.23	INTEGER	read-write	This entry is applicable only for VC-6A, VC-6AG, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS cards. Interface Analog Signaling. Must be the same for all card's ports. loopStart - for the usual trunk/phone types. groundStart - for trunks that need Ground signaling . winkStart - for trunks that need Reverse Polarity.
INT prtExVc2IfType	1.3.6.1.4.1.164.3.2.3.2.5.1.18	INTEGER	read-write	Interface Type.
INT prtExVc2ImpedanceStandard	1.3.6.1.4.1.164.3.2.3.2.5.1.40	INTEGER	read-write	This object defines the Standard used for Impedance. -G.712 - 600 Ohm - used in USA and other countries. -Q552/ETSI - used in some countries in Europe -Q522/Italy - used in Italy.
INT prtExVc2LinkTo	1.3.6.1.4.1.164.3.2.3.2.5.1.11	INTEGER	read-write	This attribute indicates the slot of the ML card to which the VC card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExVc2MeterRate	1.3.6.1.4.1.164.3.2.3.2.5.1.22	INTEGER	read-write	This entry is applicable only for VC-6A/FXO, VC-6A/FXS, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS. Meter Rate means rate of Call Meter in Public Phones, in KHz units. For some cards, the value must be the same for all card's ports.
INT prtExVc2NoiseLevelForVAD	1.3.6.1.4.1.164.3.2.3.2.5.1.37	INTEGER	read-write	This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to deal with. notApplicable - when prtExVc2VAD=off.
INT prtExVc2ObMode	1.3.6.1.4.1.164.3.2.3.2.5.1.35	INTEGER	read-write	This object defines the Net operation mode of the Omni-Bus card's port. pointToPoint - only 2 end-point ports talk; like any other voice card omniBus - many talk and listen. Like conference call. All can listen to all. pointToMultiPointSrc - There is one Master who can be heard by all. All can talk, but only the Master can hear all. Others can hear only the Master. This port is of the Master (Src). pointToMultiPointDst - There is one Master who can be heard by all. All can talk, but only the Master can hear all. Others can hear only the Master. This port is of a Destination (NOT Master).
INT prtExVc2Oos	1.3.6.1.4.1.164.3.2.3.2.5.1.10	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
INT prtExVc2OperMode	1.3.6.1.4.1.164.3.2.3.2.5.1.12	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request.
INT prtExVc2R2Delay	1.3.6.1.4.1.164.3.2.3.2.5.1.15	INTEGER	read-write	This object indicates the R2 Delay. notApplicable - for all cards except VC-2/R2.
I32 prtExVc2ReceiveGain	1.3.6.1.4.1.164.3.2.3.2.5.1.6	Integer32	read-write	Receive gain in dBm. For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8 VC-4/Omni and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps.
INT prtExVc2RemType	1.3.6.1.4.1.164.3.2.3.2.5.1.26	INTEGER	read-write	Remote Type. Applicable for VC-6A/4LB card & for IPMUX-1E Far End Type - E1,T1(T1-ESF) or T1-D4 .
INT prtExVc2ReversePolarity	1.3.6.1.4.1.164.3.2.3.2.5.1.30	INTEGER	read-write	This object Enables/Disables Reverse Polarity for this port.
INT prtExVc2RingerFrequency	1.3.6.1.4.1.164.3.2.3.2.5.1.31	INTEGER	read-write	This object selects the Ringer Frequency (Hz) for this port.
OCT prtExVc2RxBitOutput	1.3.6.1.4.1.164.3.2.3.2.5.1.21	OCTET STRING	read-write	- - - For MP (VC-Q card only) & FCD - - - This object represents 3 parameters by 2 Octets: Spare -MSB nibble, always=0 hex E Lead Output - nibble, Reverse Polarity Output- nibble, Metering Pulse Output -LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = Rx A bit 2 hex = 0010 = Rx A bit inverse 3 hex = 0011 = Rx B bit 4 hex = 0100 = Rx B bit inverse 5 hex = 0101 = Rx C bit 6 hex = 0110 = Rx C bit inverse 7 hex = 0111 = Rx D bit 8 hex = 1000 = Rx D bit inverse 9 hex = 1001 = none A-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For MP (VC-8, VC-16, VC-16A cards) - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = not used (invalid value) 2 hex = 0010 = not used (invalid value) 3 hex = 0011 = not used (invalid value) 4 hex = 0100 = not used (invalid value) 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO. - - - For WR II - - - This object represents the following 2 parameters in 1 Octet: 1. On/Off hook signaling receive mode from the T1/E1 into the FXS/FXO (MSB nibble 1). 2. E (Ear) Signaling receive mode from the T1/E1 into the E&M (LSB nibble 2). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook E (Ear) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable 1 hex = 0001 Rx A bit Rx A bit 2 hex = 0010 Rx A bit inverse Rx A bit inverse 3 hex = 0011 Rx B bit Rx B bit 4 hex = 0100 Rx B bit inverse Rx B bit inverse 5-F hex not used-invalid not Used-invalid Default value: 11
INT prtExVc2SeizeAck	1.3.6.1.4.1.164.3.2.3.2.5.1.24	INTEGER	read-write	This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Default value for WR FXO: no(2).
INT prtExVc2Sig	1.3.6.1.4.1.164.3.2.3.2.5.1.9	INTEGER	read-write	This attribute indicates the method for decoding/encoding the signaling information(on/off hook). noSignaling (1) - not using signaling (only voice). robbedBitMultiFrame(2) - is the standard method for T1 links and proprietary method for E1 links. chAssociatedE1 (3) - is valid only for E1 G.732S links. robbedBitFrame (4) - is proprietary method implimenting 7 bit for the voice and 1 bit dedicated for signaling. For some cards, this object is equal for all the ports in the specific module because of HW limitations.
INT prtExVc2SigFeedback	1.3.6.1.4.1.164.3.2.3.2.5.1.28	INTEGER	read-write	Signaling Feedback. Applicable for VC-8/FXO and VC-16/FXO cards.
INT prtExVc2SigProfile	1.3.6.1.4.1.164.3.2.3.2.5.1.13	INTEGER	read-write	This object indicates the Signaling Profile of the port. notApplicable - for VC-2 family and when prtExVc2Sig=noSignaling(1) p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4
INT prtExVc2SigService	1.3.6.1.4.1.164.3.2.3.2.5.1.32	INTEGER	read-write	Signaling Service. advanced - is relevant only for ports of VC-8, VC-16 FXS cards. It is used for Signaling Services of V5.1 or R2.
I32 prtExVc2TransGain	1.3.6.1.4.1.164.3.2.3.2.5.1.5	Integer32	read-write	Transmit gain in dBm. For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8 VC-4/Omni and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps.
OCT prtExVc2TxBitCode	1.3.6.1.4.1.164.3.2.3.2.5.1.20	OCTET STRING	read-write	- - - For MP & FCD - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = M lead 2 hex = 0010 = M lead inverse 3 hex = 0011 = Reverse Polarity 4 hex = 0100 = Metering Pulse 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For WR II - - - This object represents the following 4 parameters by 2 Octets: 1. On/Off hook signaling transmission mode from the FXS towards the T1/E1 (MSB nibble 1). 2. Default signaling bits that are not in use (nibble 2). 3. Ring Detection signaling transmission mode from the FXO towards the T1/E1(nibble 3). 4. M (Mouth) Signaling transmission mode from the E&M towards the T1/E1(LSB nibble 4). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook Default sig. Ring Detect. M (Mouth) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable. Not Applicable Not Applicable 1 hex = 0001 Tx A bit Values 1-3 are Tx A bit Tx A bit 2 hex = 0010 Tx A bit inverse for On/Off Hook Tx A bit inv. Tx A bit inv. 3 hex = 0011 Tx B bit A,B,A Inv,B Inv. Tx B bit Tx B bit 4 hex = 0100 Tx B bit inverse Values 4-7 are Tx B bit inv. Tx B bit inv. 5 hex = 0101 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid 6 hex = 0110 not Used-invalid A, A Inverse. not Used-invalid not Used-invalid 7 hex = 0111 not Used-invalid not Used-invalid not Used-invalid 8 hex = 1000 not Used-invalid Values 8-11 are not Used-invalid not Used-invalid 9 hex = 1001 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid A hex = 1010 not used-invalid B, B Inverse. not Used-invalid not Used-invalid B hex = 1011 not used-invalid The Bits order: not Used-invalid not Used-invalid C-F hex not used-invalid ABCD not Used-invalid not Used-invalid Default value: 11 11
INT prtExVc2VAD	1.3.6.1.4.1.164.3.2.3.2.5.1.36	INTEGER	read-write	This object defines whether Voice Activation Detector (VAD) will be On or Off. off - will be usually selected when a Modem is connected to the port; not a phone. notApplicable - when prtExVc2DspMode=pointToPoint.
INT prtExVc2WesternSigMode	1.3.6.1.4.1.164.3.2.3.2.5.1.38	INTEGER	read-write	This object defines the Western Signaling Mode. detector - detects signal and passes it as is. generator - generates the signal. notApplicable - when Western HW is not installed.
INT prtExVc2Wire	1.3.6.1.4.1.164.3.2.3.2.5.1.7	INTEGER	read-write	For some cards, this object is equal for all the ports in the specific card because of HW limitations. For FXO & FXS this parameter is not applicable.
prtExVc3CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.14.1.1		not-accessible	An entry in table.
I32 prtExVc3CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExVc3CnfgTable	1.3.6.1.4.1.164.3.2.3.2.14.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExVc3Connect	1.3.6.1.4.1.164.3.2.3.2.14.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExVc3EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.14.1.1.9	INTEGER	read-write	Echo canceler activation. The value will be the same for all the card's external ports.
INT prtExVc3PrtIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExVc3Rate	1.3.6.1.4.1.164.3.2.3.2.14.1.1.8	INTEGER	read-write	Rate in bps.
I32 prtExVc3ReceiveGain	1.3.6.1.4.1.164.3.2.3.2.14.1.1.6	Integer32	read-write	Receive gain in dBm.
INT prtExVc3SltIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
I32 prtExVc3TransGain	1.3.6.1.4.1.164.3.2.3.2.14.1.1.5	Integer32	read-write	Transmit gain in dBm.
INT prtExVc3Wire	1.3.6.1.4.1.164.3.2.3.2.14.1.1.7	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
prtExVcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.1.1		not-accessible	An entry in table.
I32 prtExVcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtExVcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtExVcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.1.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtExVcPbxFrame	1.3.6.1.4.1.164.3.2.3.2.15.1.1.8	INTEGER	read-write	This object is the frame parameter for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 values for the VC-PBX/T1 card. E1 values for the VC-PBX/E1 card. notApplicable - for the VC-PBX card. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7)
INT prtExVcPbxGroup	1.3.6.1.4.1.164.3.2.3.2.15.1.1.5	INTEGER	read-only	The group object links together several VC-PBX cards, concerning compression of the same input T1/E1 link time-slots. When ports of different slots have the same group, they are linked. When ports have a different group, they are not linked. For VC-PBX/T1 and E1 cards, this object is - their own IO Slot. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVcPbxIdleCode	1.3.6.1.4.1.164.3.2.3.2.15.1.1.14	INTEGER	read-write	Determines the code for transmission in empty time slots. notApplicable - for VC-PBX card .
INT prtExVcPbxLineCode	1.3.6.1.4.1.164.3.2.3.2.15.1.1.10	INTEGER	read-write	This object is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for VC-PBX/T1 E1 line code parameters for VC-PBX/E1 notApplicable - for VC-PBX This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExVcPbxLineLength	1.3.6.1.4.1.164.3.2.3.2.15.1.1.11	INTEGER	read-write	This object is the line length parameter. It is applicable only for the VC-PBX/T1 card. notApplicable - for the VC-PBX and VC-PBX/E1 card. lenXXXpXXXft = len-XXX-XXXft.
INT prtExVcPbxLinkTo	1.3.6.1.4.1.164.3.2.3.2.15.1.1.12	INTEGER	read-write	This object indicates the slot of the ML card to which the VC-PBX/T1, VC-PBX/E1 card Transparent TSs are mapped. notApplicable - for VC-PBX card AND for VC-PBX/T1, VC-PBX/E1 cards, when prtExVcPbxTransparent=no . In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExVcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExVcPbxRestoreTime	1.3.6.1.4.1.164.3.2.3.2.15.1.1.9	INTEGER	read-write	The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface. ccittE1 - is applicable only for VC-PBX/E1 card notApplicable - is applicable for VC-PBX card
INT prtExVcPbxSignalOper	1.3.6.1.4.1.164.3.2.3.2.15.1.1.13	INTEGER	read-write	This object indicates the Signaling Operation of the VC-PBX/T1, VC-PBX/E1 external port. notApplicable - for VC-PBX card normal - all 4 signaling bits are transferred. bEqA - copy the A bit into the B bit. Applicable only for VC-PBX/T1.
INT prtExVcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVcPbxTransparent	1.3.6.1.4.1.164.3.2.3.2.15.1.1.6	INTEGER	read-write	This object indicates whether the Transparent transfer of Time-Slots is required or not. Time-Slots transferred by Transparent, will not be compressed. no - applicable only for VC-PBX/T1 and VC-PBX/E1 cards yes - applicable only for VC-PBX/T1 and VC-PBX/E1 cards notApplicable - only for VC-PBX cards.
I32 prtExVcPbxTransSignalTs	1.3.6.1.4.1.164.3.2.3.2.15.1.1.7	Integer32	read-write	This object specifies the ML Time-Slot dedicated to the signaling of the PABX Transparent TSs. None = 255. When prtExVcPbxTransparent=no this object's value=None (255) When prtExVcPbxTransparent=notApplicable, this object's value=None (255). When prtExVcPbxTransparent=yes: - for VC-PBX/T1 ports, this object's valid values are 1..16 or None (255). - for VC-PBX/E1 ports, this object's value will be 16 or None (255).
I32 prtExVcPbxTsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtExVcPbxTsEntry	1.3.6.1.4.1.164.3.2.3.2.15.4.1		not-accessible	An entry in table.
INT prtExVcPbxTsIConPrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.7	INTEGER	read-write	This attribute indicates the port to which this TS is connected. For VF-PBX cards, only inPrt1..inPrt6 ports are valid. For VF-24/30/48/60 cards: - for prtExVcPbxTsMode=transparent or voiceTransparent, the valid ports are ML ports (exPrt1.. exPrt8, inPrt1.. inPrt8) - for prtExVcPbxTsMode=compressed or compressedCcs, the valid ports are internal ports of the same card (inPrt1..inPrt8) noConnect - when prtExVcPbxTsIConSlot=noConnect.
INT prtExVcPbxTsIConSlot	1.3.6.1.4.1.164.3.2.3.2.15.4.1.6	INTEGER	read-write	For VF-PBX cards, the io1..io12 values are applicable only when prtExVcPbxTsMode=compressed. Otherwise, its value should be noConnect. For VF-24/30/48/60 cards: - when prtExVcPbxTsMode=transparent or voiceTransparent, the io1..io12 values are applicable, indicating the ML Slot this TS is connected to. - when prtExVcPbxTsMode=compressed or compressedCcs, the value will be the same as prtExVcPbxTsSltIdx, since the compression is done within the same card. - for rest of the prtExVcPbxTsMode values, the value will be: noConnect. This object indicates whether the specified compressed/transparent time slot is connected/routed internally in the Agent and to which card it is connected. For VF-PBX card, the valid selectable slots are either the current one, (prtExVcPbxTsSltIdx), or a slot containing a VF-PBX card. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
I32 prtExVcPbxTsIConTs	1.3.6.1.4.1.164.3.2.3.2.15.4.1.8	Integer32	read-write	This attribute indicates the ML TS to which this TS is connected. This object is not applicable for VF-PBX cards. For VF-24/30/48/60 cards it is applicable only when prtExVcPbxTsMode=transparent or voiceTransparent. The valid time slots are 1..24 for ML T1 cards and 1..31 for ML E1 cards. notApplicable - 255.
I32 prtExVcPbxTsIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.4	Integer32	read-only	This attribute indicates a unique PABX time slot position. The valid time slots are 1..24 for T1 cards and 1..31 for E1 cards.
INT prtExVcPbxTsMode	1.3.6.1.4.1.164.3.2.3.2.15.4.1.5	INTEGER	read-write	This attribute indicates the usage, process and way of the specific PABX TS towards its destination: unused - the TS is not used (no processing, no destination). compressed - the TS is used, sent for compression to an internal port (for VF-PBX cards: 1..6 for of either the same card or a VF-PBX card of the same group). For VF-24/30/48/60 - 'compressed' represents 'compressed Voice' (to differentiate it from 'compressedCcs'). In this case, the TS is compressed by an internal port (1..8). transparent - the TS is used; no processing. It is sent directly for Bypass to a ML card the VF port/TS is linked to. compressedCcs - supported only by VF-24/30/48/60 cards. The TS is used; sent for compression to the CPU. mng - the TS is used for Management (this option is used when the external port is connected to another product that has to be managed via this dedicated TS. ccs1..ccs8 - supported only by VF-24/30/48/60 cards. Compressed TS that comes from a bundle of V5.1 or V5.2 PBX. ss7n1..ss7n8 - supported only by VF-24/30/48/60 cards. Compressed TS that comes from a bundle of V5.1 or V5.2 PBX. ss7n1 can work versus Vmux having prtExPh1MlTsType=ss7(6).
INT prtExVcPbxTsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.3	INTEGER	read-only	This attribute indicates a unique port number. VCPBX/E1, VCPBX/T1, VFPBX/E1, VFPBX/T1, VF-24/T1 and VF-30 cards have only one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. VFS cards have also internal ports.
U32 prtExVcPbxTsRemConnID	1.3.6.1.4.1.164.3.2.3.2.15.4.1.11	Unsigned32	read-write	This attribute indicates the Connection ID with the Remote unit. notApplicable = 0.
INT prtExVcPbxTsRemPrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.9	INTEGER	read-write	This attribute indicates the end-point port on the Remote unit. VF-24/T1 and VF-30/E1 cards have one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. noConnect - when prtExVcPbxTsMode=unused, transparent, voiceTransparent or mng.
I32 prtExVcPbxTsRemTs	1.3.6.1.4.1.164.3.2.3.2.15.4.1.10	Integer32	read-write	This attribute indicates the end-point TS on the Remote unit. The valid time slots are 1..24 for T1 ports and 1..31 for E1 ports. notApplicable - 255.
INT prtExVcPbxTsSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
U32 prtExVcPbxTsSourcePrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.13	Unsigned32	read-write	For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Port within the Slot of the Analog Voice Card, we want to compress. exPrt1 - exPrt16 = 1 - 16 noConnect=100 - when prtExVcPbxTsCvServiceSlot=noConnect.
INT prtExVcPbxTsSourceSlot	1.3.6.1.4.1.164.3.2.3.2.15.4.1.12	INTEGER	read-write	For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Slot of the Analog Voice port we want to compress. io1..io12 values are applicable only when prtExVcPbxTsMode=compressed(voice). Otherwise, its value should be noConnect. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
prtExVcPbxTsTable	1.3.6.1.4.1.164.3.2.3.2.15.4		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtFrPlusCnfg	1.3.6.1.4.1.164.3.2.3.2.18
prtFrPlusCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.18.1.1		not-accessible	An entry in table.
I32 prtFrPlusCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtFrPlusCnfgTable	1.3.6.1.4.1.164.3.2.3.2.18.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
OCT prtFrPlusNotSegmentedPriorities	1.3.6.1.4.1.164.3.2.3.2.18.1.1.4	OCTET STRING	read-write	This parameter is relevant only for FR+ protocol and asks the MXcess NOT to segment data with specified priorities: from LSB: bit 1 is for priority 1, bit 2 is for priority 2, .... till bit 7 for priority 7. - a priority selected to be segmented : its bit will be '0' - a priority not to be segmented : its bit will be '1' Default is 00000000; i.e, segment all priorities.
I32 prtFrPlusPrtIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be: - for ISDN cards: inPrt1(101)->inPrt50(150) - for MHS1 card : exPrt1(1) - for MHS3, MLS3 cards: exPrt1(1)->exPrt3(3) - for MLS6 cards: exPrt1(1)->exPrt6(6).
INT prtFrPlusSltIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.2	INTEGER	read-only	Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
C32 prtFrRxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.23	Counter32	read-only	Number of data frames received by this port during the selected interval, exceeding the Burst Committed value.
C32 prtFrRxBecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.19	Counter32	read-only	Number of frames received by this port during the selected interval, indicating backward congestion.
C32 prtFrRxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.21	Counter32	read-only	Number of data frames received by this port during the selected interval, exceeding the Burst Excess value.
C32 prtFrRxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.15	Counter32	read-only	All the frames discarded due to congestion, received by this port during the selected interval.
C32 prtFrRxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.13	Counter32	read-only	The number of De frames discarded due to congestion, received by this port during the selected interval.
C32 prtFrRxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.11	Counter32	read-only	The number of De frames received by this port during the selected interval.
C32 prtFrRxFecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.17	Counter32	read-only	Number of frames received by this port during the selected interval, indicating forward congestion.
C32 prtFrRxMngFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.9	Counter32	read-only	The management number of frames received by this port during the selected interval.
C32 prtFrRxTotalBytes	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.7	Counter32	read-only	The total number of bytes received by this port during the selected interval.
C32 prtFrRxTotalFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.5	Counter32	read-only	The total number of frames received by this port during the selected interval.
prtFrStatis	1.3.6.1.4.1.164.3.1.4.1.3.1
prtFrStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1		not-accessible	An entry in table.
INT prtFrStatisInvIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.3	INTEGER	read-only	The Interval of 15 min. for which the following statistics counters are applicable.
INT prtFrStatisPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtFrStatisSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
prtFrStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.1.1		not-accessible	This table is applicable only for an active port running an FR protocol .
I32 prtFrTimeElapsed	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.4	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0.
C32 prtFrTxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.24	Counter32	read-only	Number of data frames sent by this port during the selected interval, exceeding the Burst Committed value.
C32 prtFrTxBecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.20	Counter32	read-only	Number of frames sent by this port during the selected interval, indicating backward congestion.
C32 prtFrTxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.22	Counter32	read-only	Number of data frames sent by this port during the selected interval, exceeding the Burst Excess value.
C32 prtFrTxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.16	Counter32	read-only	All the frames discarded due to congestion, sent by this port during the selected interval.
C32 prtFrTxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.14	Counter32	read-only	The number of De frames discarded due to congestion, sent by this port during the selected interval.
C32 prtFrTxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.12	Counter32	read-only	The number of De frames sent by this port during the selected interval.
C32 prtFrTxFecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.18	Counter32	read-only	Number of frames sent by this port during the selected interval, indicating forward congestion.
C32 prtFrTxMngFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.10	Counter32	read-only	The management number of frames sent by this port during the selected interval.
C32 prtFrTxTotalBytes	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.8	Counter32	read-only	The total number of bytes sent by this port during the selected interval.
C32 prtFrTxTotalFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.6	Counter32	read-only	The total number of frames sent by this port during the selected interval.
prtGen	1.3.6.1.4.1.164.3.3.3.1
INT prtGenActiveStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.5	INTEGER	read-only	This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the port is not connected according to the active config. offLine(3) indicates that the port is down (not working) due to any problem. onLine (4) indicates that the port is up (working) offLineRedundancy(5) indicates that the port is down because it is a redundant port. onLineRedundancy (6) indicates that this is a redundant port which is up and works as the active link.
INT prtGenAlrClearCmd	1.3.6.1.4.1.164.3.3.3.1.1.1.13	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the port level alarms . Upon completion, the value will automatically change to off(2). noOp - will be used by agents that do not support this feature or object.
INT prtGenAlrMaskAll	1.3.6.1.4.1.164.3.3.3.1.1.1.14	INTEGER	read-write	on(3) - will mask all the alarms of the selected port off(2)- will unmask all alarms of the selected port except the ones selected by the prtAlrMaskTable. noOp - will be used by agents that do not support this feature or object.
INT prtGenAlrStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.6	INTEGER	read-only	Indicates the alarm state at port (ch) agent level. This object will be: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT prtGenCnfgBusConnection	1.3.6.1.4.1.164.3.1.4.2.3.1.7	INTEGER	read-write	This object indicates the support of the card regarding Bus Connection. Same value for all ports of the card. partial = 2 Buses (AB) full = 4 Buses (ABCD) partial CD = 2 Buses CD Actually the support depends on the card's HW. But, since CL has to assign data on Buses even when the card is not installed, this object has to be configured. If the actual card installed will not match the value configured, an Alarm will be issued.
INT prtGenCnfgConnect	1.3.6.1.4.1.164.3.1.4.2.3.1.11	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
prtGenCnfgEntry	1.3.6.1.4.1.164.3.1.4.2.3.1		not-accessible	An entry in table.
I32 prtGenCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
INT prtGenCnfgInbandMng	1.3.6.1.4.1.164.3.1.4.2.3.1.8	INTEGER	read-write	This object indicates whether Inband Management is used over the link.
INT prtGenCnfgInbandMngRoutProt	1.3.6.1.4.1.164.3.1.4.2.3.1.9	INTEGER	read-write	This object indicates the Inband Mng Routing Protocol of the port.
I32 prtGenCnfgLinkToPort	1.3.6.1.4.1.164.3.1.4.2.3.1.5	Integer32	read-write	This attribute indicates the port in the prtGenCnfgLinkToSlot of the ML card to which the IO port is mapped. For MP: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109), inPrt10 (110), inPrt11 (111), inPrt12 (112), inPrt13 (113), inPrt14 (114), inPrt15 (115), inPrt16 (116), inPrt17 (117), inPrt18 (118), inPrt19 (119), inPrt20 (120), inPrt21 (121), inPrt22 (122), inPrt23 (123), inPrt24 (124), inPrt25 (125), inPrt26 (126), inPrt27 (127), inPrt28 (128), inPrt29 (129), inPrt30 (130), inPrt31 (131), inPrt32 (132), inPrt33 (133), inPrt34 (134), inPrt35 (135), inPrt36 (136), inPrt37 (137), inPrt38 (138), inPrt39 (139), inPrt40 (140), inPrt41 (141), inPrt42 (142), inPrt43 (143), inPrt44 (144), inPrt45 (145), inPrt46 (146), inPrt47 (147), inPrt48 (148), inPrt49 (149), inPrt50 (150), inPrt51 (151), inPrt52 (152), inPrt53 (153), inPrt54 (154), inPrt55 (155), inPrt56 (156), inPrt57 (157), inPrt58 (158), inPrt59 (159), inPrt60 (160), inPrt61 (161), inPrt62 (162), inPrt63 (163), inPrt64 (164), inPrt65 (165), inPrt66 (166), inPrt67 (167), inPrt68 (168), inPrt69 (169), inPrt70 (170), inPrt71 (171), inPrt72 (172), inPrt73 (173), inPrt74 (174), inPrt75 (175), inPrt76 (176), inPrt77 (177), inPrt78 (178), inPrt79 (179), inPrt80 (180), inPrt81 (181), inPrt82 (182), inPrt83 (183), inPrt84 (184), notApplicable (255)
INT prtGenCnfgLinkToSlot	1.3.6.1.4.1.164.3.1.4.2.3.1.4	INTEGER	read-write	This attribute indicates the slot of the ML card to which the IO port is mapped.
I32 prtGenCnfgPortId	1.3.6.1.4.1.164.3.1.4.2.3.1.6	Integer32	read-write	IO Port Id for V5.1 use. This object is applicable only for part of the PSTN and ISDN IO ports. Generally, 0 is a valid value. Nevertheless, for ports that do not support this object, the value will be: notApplicable= 0
INT prtGenCnfgProtectionMode	1.3.6.1.4.1.164.3.1.4.2.3.1.10	INTEGER	read-write	This object indicates the Protection Mode of the port. notApplicable- when Bus Protection Point=No. For VC-4/Omni card this object is supported RO.
I32 prtGenCnfgPrtIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.3	Integer32	read-only	This attribute indicates a unique external or internal port number. For MP: exPrt1 (1) .. exPrt16 (16) , notApplicable(100), inPrt1 (101) .. inPrt84 (184)
INT prtGenCnfgSignalingType	1.3.6.1.4.1.164.3.1.4.2.3.1.12	INTEGER	read-write	This object selects the Type of Signaling used by the port.
INT prtGenCnfgSltIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
prtGenCnfgTable	1.3.6.1.4.1.164.3.1.4.2.3		not-accessible	This table allows the user to configure general port parameters.
prtGenEntry	1.3.6.1.4.1.164.3.3.3.1.1.1		not-accessible	An entry in table.
INT prtGenExtInt	1.3.6.1.4.1.164.3.3.3.1.1.1.3	INTEGER	read-only	This attribute describes the type of the designated port. Exteral port is a port with a physical connector. Internal port might be of two types, one is a composite port which collects data of a few external ports into a common bandwidth (usually routed trough DS1 link); the other type is internal ports which get only part of external port data (usually a few DS0's). In the Kilomux-2100, the internal(3) value is used for composite channels or sub-channels of an ISDN Ch.
I32 prtGenIfIndex	1.3.6.1.4.1.164.3.3.3.1.1.1.4	Integer32	read-only	This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx, the value will be '7fffffff'h.
STR prtGenInterfaceType	1.3.6.1.4.1.164.3.3.3.1.1.1.12	DisplayString	read-only	This attribute indicates a unique HW interface type of the selected port. Examples: - for T1 cards: DSU, CSU - for E1 cards: DSU, LTU - for HS cards: v35, rs422, x21 etc...
OCT prtGenParamStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.15	OCTET STRING	read-only	This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For HS cards (Dxc cards) - 1 octet: Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 0 and 1 indicates RTS control signal state: Bit 1: '1'=active ; '0'=notActive Bit 0 (LSB): '1'=unknown ; '0'=NA - For HS-U/1 external port (MP card, used in FCD-M) - 1 Octet: Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For VC-6, VC-12, VC-12/6 external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 \|___\| \|_______\| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=Unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|___________\| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For KM2100, KVF.5 cards - indicates the status of A and B signaling for each internal channel. 1 Octet: Bit - 7 6 5 4 3 2 1 0 \|_____\| \|_\| \|_\| spare B A Bit 0 (LSB) and Bit 1 : A status Bit 2 and Bit 3 : B status 00 - Off 01 - On 11 - Unknown - For FCD-W, NETWORK and USER ports - 1 Octet Status of Control Signals: '1'=On ; '0'=Off or when not applicable Bit - 7 6 5 4 3 2 1 0 Bit 7 (MSB) - Signal Loss (applicable only for G.703 interface) Bit 6 - CONTROL (applicable only for X.21 interface) Bit 5 - INDICATION (applicable only for X.21 interface) Bit 4 - DSR (applicable only for V.35 interface) Bit 3 - RTS (applicable only for V.35 interface) Bit 2 - CTS (applicable only for V.35 interface) Bit 1 - DTR (applicable only for V.35 interface) Bit 0 - DCD (applicable only for V.35 interface) - For DXC R6 , D8U, D16U External ports - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For DXC DE1-HDSL, DT1-HDSL, D16GSDSL, D8SL External ports - 2 Octets MSB octet: far-end modem channel interface LSB octet: Sub Link existence (Y/N), far-end modem type, synchronization with far-end modem MSB octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) 0000 1011 = IR-ETH-QN Rest of the combinations: reserved LSB octet: Bit 7 6 5 4 3 2 1 0 LSB \| \|___________\| \|__\| SL modem sync or Box material SL: modem: 00000 = other sync: 00 = not sync 0=not exist 00001 = unknown 01 = sync 1=exists 00010 = ASMi-31/2 10 = reserved 00011 = HCD-E1 11 = reserved Box material 00100 = HTU-E1 (for D8SL card): 00101 = HTU-2 0=metal 00110 = ASMi-52 SA/2W/Slave 1=plastic 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD 01110 = D8GSDSL card of DXC-3000 01111 = ASMi-52A Rest = reserved
prtGenParamTable	1.3.6.1.4.1.164.3.3.3.1.1		not-accessible	A table.
I32 prtGenPrtIdx	1.3.6.1.4.1.164.3.3.3.1.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT prtGenRdnStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.16	INTEGER	read-only	This object indicates if this port is part of a redundant pair and in this case, if it is On or Off. none(1) - No redundancy or Not Applicable off (2) - the port is part of a redundant pair and it is Off from Redundancy point of view (not the port used). on (3) - the port is part of a redundant pair and it is On from Redundancy point of view (it is the port used).
INT prtGenSlt	1.3.6.1.4.1.164.3.3.3.1.1.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. The Kilomux should use the enumerated starting with kmx.
I32 prtGenTestCmd	1.3.6.1.4.1.164.3.3.3.1.1.1.9	Integer32	read-write	Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMask). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the requested value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system.
OCT prtGenTestCmdXP	1.3.6.1.4.1.164.3.3.3.1.1.1.18	OCTET STRING	read-write	This is an Expanded test command of the prtGenTestCmd object. The prtGenTestCmd object reached its maximum, being an Integer with 31 bits. Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMaskXP). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the requested value is 00000003 hex -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system.
I32 prtGenTestDuration	1.3.6.1.4.1.164.3.3.3.1.2.1.3	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to the specified test . The resolution will be a minute, and the maximum duration is limited to 30 minutes . A zero value specifies no time limitation. When the test isn't active the agent initiates this object to 2 min. when the duration is needed and to 0 if it's not required.
prtGenTestDurationEntry	1.3.6.1.4.1.164.3.3.3.1.2.1		not-accessible	An entry in table.
prtGenTestDurationTable	1.3.6.1.4.1.164.3.3.3.1.2		not-accessible	A table.
INT prtGenTestIdx	1.3.6.1.4.1.164.3.3.3.1.2.1.2	INTEGER	read-only	This attribute indicates the test, the duration refers.
I32 prtGenTestMask	1.3.6.1.4.1.164.3.3.3.1.1.1.8	Integer32	read-only	This is a mask which indicates which tests from the 'prtGenTestCmd' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
OCT prtGenTestMaskXP	1.3.6.1.4.1.164.3.3.3.1.1.1.17	OCTET STRING	read-only	This is an Expanded test mask of the prtGenTestMask object. The prtGenTestMask object reached its maximum, being an Integer with 31 bits. This object indicates which tests from the 'prtGenTestCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
I32 prtGenTestPrtIdx	1.3.6.1.4.1.164.3.3.3.1.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtGenTestRunning	1.3.6.1.4.1.164.3.3.3.1.1.1.10	Integer32	read-only	This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only!
OCT prtGenTestRunningXP	1.3.6.1.4.1.164.3.3.3.1.1.1.19	OCTET STRING	read-only	This is an Expanded object of the prtGenTestRunning object. The prtGenTestRunning object reached its maximum, being an Integer with 31 bits. This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only!
INT prtGenTestStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.7	INTEGER	read-only	This attribute will be on(3) when there is at least one test in progress (running) on the port; otherwise the value will be off(2).
I32 prtGenTsCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
prtGenTsEntry	1.3.6.1.4.1.164.3.3.3.1.3.1		not-accessible	An entry in table.
I32 prtGenTsIConPrt	1.3.6.1.4.1.164.3.3.3.1.3.1.5	Integer32	read-write	This attribute indicates the internally (In Mux) connected port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside ports will be for example, the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * noConnection - will be indicated as 10 for DXC and FCD-E1/T1. - will be indicated as 100 for FCD-E1/I and SMODs. * Split TS (same TS is Split to several ports) - 11. * notApplicable- will be indicated as 100 for LRS IMODs. All HS port's timeslots must have the same destination port.
I32 prtGenTsIConTs	1.3.6.1.4.1.164.3.3.3.1.3.1.6	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 (or HS) Card. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling. * For DXC: All HS port's timeslots must start with Timeslot no.1
I32 prtGenTsIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.3	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 or HS Card . In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
I32 prtGenTsPrtIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.2	Integer32	read-only	This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
prtGenTsTable	1.3.6.1.4.1.164.3.3.3.1.3		not-accessible	The write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch),exept some products which enable direct writing to the ActiveCnfg. This is written in the respective product's spec.
INT prtGenTsType	1.3.6.1.4.1.164.3.3.3.1.3.1.4	INTEGER	read-write	The type of Timeslot. If the source or destination port is an HS port,'TS Type' must be 'data'. nc - means that this TimeSlot is not connected. voice, data, vcMP - also mean that this TS is connected. mng - means that this TS is dedicated to Management (not connected to another port.
INT prtGenType	1.3.6.1.4.1.164.3.3.3.1.1.1.11	INTEGER	read-only	This object describes the type of the selected port. idsl - applicable for external ports of HS-U cards (of DXC) when interface is LT-1.
prtHdsl	1.3.6.1.4.1.164.3.3.3.7
STR prtHdslCompHwVer	1.3.6.1.4.1.164.3.3.3.7.1.1.7	DisplayString	read-only	This object indicates the Hardware Version of the component (Piggyback card) supporting this interface.
STR prtHdslCompSwVer	1.3.6.1.4.1.164.3.3.3.7.1.1.6	DisplayString	read-only	This object indicates the Software Version of the component (Piggyback card) supporting this interface.
prtHdslEntry	1.3.6.1.4.1.164.3.3.3.7.1.1		not-accessible	An entry in table.
I32 prtHdslIdx	1.3.6.1.4.1.164.3.3.3.7.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The HDSL ports will be external. For port index, see product specification.
INT prtHdslLinkType	1.3.6.1.4.1.164.3.3.3.7.1.1.5	INTEGER	read-only	The Link Type. msdsl2w - MSDSL 2 Wire hdsl2w - HDSL 2 Wire hdsl4w - HDSL 4 Wire gDsl - G.DSL
INT prtHdslMaxRate	1.3.6.1.4.1.164.3.3.3.7.1.1.4	INTEGER	read-write	Maximum Rate of the xDSL Line, in Kbps units. This object can be Set only for a Central unit.
INT prtHdslMode	1.3.6.1.4.1.164.3.3.3.7.1.1.2	INTEGER	read-write	This object indicates the HDSL mode.
INT prtHdslRptrType	1.3.6.1.4.1.164.3.3.3.7.1.1.3	INTEGER	read-only	The Repeater between Near and Far modem. none - no repeater exists between the modems hrpt - HRPT repeater exists between the modems.
prtHdslTable	1.3.6.1.4.1.164.3.3.3.7.1		not-accessible	HDSL port table.
prtHS	1.3.6.1.4.1.164.3.3.3.3
prtHs4Cnfg	1.3.6.1.4.1.164.3.2.3.2.7
INT prtHSBertCountClr	1.3.6.1.4.1.164.3.3.3.3.2.1.3	INTEGER	read-write	Setting this object (to on) initiate bert counter clear operation. Valid only when bert test is active on the specific port. (Every time a new bert test starts, the counter is automatically cleared; this command enables clearing the counter while the test is running).
prtHSBertEntry	1.3.6.1.4.1.164.3.3.3.3.2.1		not-accessible	An entry in table.
I32 prtHSBertPrtIdx	1.3.6.1.4.1.164.3.3.3.3.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT prtHSBertSlt	1.3.6.1.4.1.164.3.3.3.3.2.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
prtHSBertTable	1.3.6.1.4.1.164.3.3.3.3.2		not-accessible	A table.
I32 prtHSBertTestResult	1.3.6.1.4.1.164.3.3.3.3.2.1.4	Integer32	read-only	This object indicates the number of Bit Error Rate indicated during the BERT test. Active only when bert test is running on the selected port.
INT prtHSClkMode	1.3.6.1.4.1.164.3.3.3.3.1.1.6	INTEGER	read-write	Clock Mode of the user data channel. dce - DACS operates as a DCE and provides transmit and receive clocks to the synchronous user DTE. dte1- DACS supplies the receive clock to the user equipment and accepts the user transmit clock. dte2- DACS requires transmit and receive clocks from the user equipment.
INT prtHSClkPolarity	1.3.6.1.4.1.164.3.3.3.3.1.1.14	INTEGER	read-write	This object indicates the clock polarity.
I32 prtHSCnfgIdx	1.3.6.1.4.1.164.3.3.3.3.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
INT prtHSCTS	1.3.6.1.4.1.164.3.3.3.3.1.1.7	INTEGER	read-write	Selection of CTS line state in the user data channel. on - CTS continuously ON. rts - CTS line follows the RTS line.
INT prtHSDCD	1.3.6.1.4.1.164.3.3.3.3.1.1.13	INTEGER	read-write	Selection of DCD line state in the user data channel. linkOK - DCD line is ON only when active link is OK. on - DCD continuously ON.
prtHsfCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.6.1		not-accessible	An entry in table.
I32 prtHsfCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relate to the TmpCnfg.
prtHsfCnfgTable	1.3.6.1.4.1.164.3.2.3.2.6		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtHSFifoSize	1.3.6.1.4.1.164.3.3.3.3.1.1.5	INTEGER	read-write	This object selects the size of the user data channel buffer FIFO used in the DTE2 mode. In the other modes, buffer size is automatically set by the DACS agent. Buffer FIFO size in bits, corresponds to FIFO lengths of +/-16, +/-30, +/-52, +/-72 bits.
INT prtHsfPrtIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.3	INTEGER	read-only	This attribute indicates a unique external port index. Hs2 has only two ports (exPrt1,exPrt2). Hs3 has three ports (exPrt1,exPrt2,exPrt3). Hsq and hsqN has four ports. Hs6 has six external ports. Hs12 has twelve external ports. inPrt1, inPrt2 - are relevant for VID card.
INT prtHsfSltIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
prtHsiCnfg	1.3.6.1.4.1.164.3.2.3.2.8
STR prtHSInbandLoopActPattern	1.3.6.1.4.1.164.3.3.3.3.1.1.11	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig.
INT prtHSInbandLoopback	1.3.6.1.4.1.164.3.3.3.3.1.1.9	INTEGER	read-write	This object indicates if Inband Loopback from the Network should be enabled or disabled.
STR prtHSInbandLoopDeactPattern	1.3.6.1.4.1.164.3.3.3.3.1.1.12	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig.
INT prtHSInbandLoopPatternCfg	1.3.6.1.4.1.164.3.3.3.3.1.1.10	INTEGER	read-write	This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtHSActivatePolyPattern and prtHSDeactivatePolyPattern.
INT prtHSInterfaceType	1.3.6.1.4.1.164.3.3.3.3.1.1.15	INTEGER	read-write	This object indicates the selected electrical interface type.
prtHSParamEntry	1.3.6.1.4.1.164.3.3.3.3.1.1		not-accessible	An entry in table.
prtHSParamTable	1.3.6.1.4.1.164.3.3.3.3.1		not-accessible	A table.
I32 prtHSPrtIdx	1.3.6.1.4.1.164.3.3.3.3.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT prtHSRate	1.3.6.1.4.1.164.3.3.3.3.1.1.4	INTEGER	read-write	This object indicates the port rate (speed). auto - rate is selected automatically by system.
prtHsrCnfg	1.3.6.1.4.1.164.3.2.3.2.10
INT prtHSRtsState	1.3.6.1.4.1.164.3.3.3.3.1.1.8	INTEGER	read-only	RTS state of the port.
INT prtHSSlt	1.3.6.1.4.1.164.3.3.3.3.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtHSUnframed	1.3.6.1.4.1.164.3.3.3.3.1.1.16	INTEGER	read-write	Unframed line for HS ports. yes - means that all TSs must be transferred, including TS0. In this case, prtHSRate must be r31x56eq1736Kbps OR r31x64eq1984Kbps.
prtI	1.3.6.1.4.1.164.3.3.3.6
prtICnfgEntry	1.3.6.1.4.1.164.3.3.3.6.1.1		not-accessible	An entry in table.
I32 prtICnfgIdx	1.3.6.1.4.1.164.3.3.3.6.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
prtICnfgTable	1.3.6.1.4.1.164.3.3.3.6.1		not-accessible	A table.
INT prtIConnect	1.3.6.1.4.1.164.3.3.3.6.1.1.4	INTEGER	read-write	D channel connection. no - disconnected yes - connected.
I32 prtIIdx	1.3.6.1.4.1.164.3.3.3.6.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The ISDN B1, B2, D channels will be inside ports. For port index, see product specification.
prtIn1p6VcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.2.1		not-accessible	An entry in table.
I32 prtIn1p6VcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtIn1p6VcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtIn1p6VcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.2.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtIn1p6VcPbxEchoCanceler	1.3.6.1.4.1.164.3.2.3.2.15.2.1.6	INTEGER	read-write	Echo canceler activation.
I32 prtIn1p6VcPbxPabxTs	1.3.6.1.4.1.164.3.2.3.2.15.2.1.7	Integer32	read-only	This object defines the PABX Time-Slot assigned to this internal port. For a T1 link, the valid values are: 1 .. 24. For an E1 link, the valid values are: 1 .. 31. This object is NOT applicable when prtIn1p6VcPbxConnect=no. This object is applicable for all cards of VC-PBX family. Default=the internal port index (1..6).
INT prtIn1p6VcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtIn1p6VcPbxRate	1.3.6.1.4.1.164.3.2.3.2.15.2.1.5	INTEGER	read-write	This object indicates the port Rate. For Normal mode (prtIn7p8VcPbxMode=normal), only part of the values are valid (constant rate). For Server mode (prtIn7p8VcPbxMode=server), all values are applicable (user can select the desired compression rate).
INT prtIn1p6VcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
prtIn7p8VcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.3.1		not-accessible	An entry in table.
I32 prtIn7p8VcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtIn7p8VcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtIn7p8VcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.3.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtIn7p8VcPbxLinkTo	1.3.6.1.4.1.164.3.2.3.2.15.3.1.9	INTEGER	read-write	This object indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For Server mode (prtIn7p8VcPbxMode=server), this object is not applicable. Both ports, 7 and 8 should be linked to the same Slot. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtIn7p8VcPbxMode	1.3.6.1.4.1.164.3.2.3.2.15.3.1.5	INTEGER	read-write	This object indicates the working mode of the port: - normal - the compressed voice will be sent to an MTML card inside the Mux. - server - the compressed voice will be sent to the Digital Voice connector, as a service to an outside user.
INT prtIn7p8VcPbxOos	1.3.6.1.4.1.164.3.2.3.2.15.3.1.8	INTEGER	read-write	Out of service Signaling mode.
INT prtIn7p8VcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtIn7p8VcPbxRate	1.3.6.1.4.1.164.3.2.3.2.15.3.1.6	INTEGER	read-write	This object indicates the port Main Rate. For Server mode (prtIn7p8VcPbxMode=server), the value will be notApplicable.
INT prtIn7p8VcPbxSignalMode	1.3.6.1.4.1.164.3.2.3.2.15.3.1.7	INTEGER	read-write	This object indicates the Signal Mode. For Server mode (prtIn7p8VcPbxMode=server), the only valid values are: - none - aBit
INT prtIn7p8VcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
prtInHsiCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.8.2.1		not-accessible	An entry in table.
I32 prtInHsiCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtInHsiCnfgTable	1.3.6.1.4.1.164.3.2.3.2.8.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. This table is not applicable for MP-2100 HS-U card type.
I32 prtInHsiConcentratedTo	1.3.6.1.4.1.164.3.2.3.2.8.2.1.6	Integer32	read-write	The Concentration D Channel of the prtInHsiPrtIdx port. The port always belongs to the same card as prtInHsiPrtIdx port. This object is applicable only when prtInHsiRate=concentrated. Valid values: - notApplicable: 255 - for MP-2200: HS-S12, HS-U12 cards: inPrt37 (137) .. inPrt48 (148). HS-S6, HS-U6 cards: inPrt19 (119) .. inPrt24 (124). - for DXC: HS-U8 cards: 112 .. 254 HS-U16 cards: 112 .. 258. See DXC R6 spec for port index convention.
INT prtInHsiConnect	1.3.6.1.4.1.164.3.2.3.2.8.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
I32 prtInHsiPrtIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.3	Integer32	read-only	A unique port identifier within the card. Valid values for MP: inPrt1 (101) .. inPrt48 (148). Valid values for DXC: 11012.. 25316. See DXC R6 spec for port index convention.
INT prtInHsiRate	1.3.6.1.4.1.164.3.2.3.2.8.2.1.5	INTEGER	read-write	This object indicates the port speed. For HS-U/I and HS-S ports: 2 bit - up to 9600bps 4 bit - 19200bps 8 bit - 38400bps .. 64kbps. concentrated - this D channel goes to a Concentration channel, that represents many channels that this value was selected for them. The Concentrated channel is an Internal D Channel of the same card. This value is applicable only for D channels, except Concentration channel itself. --for HS-S and HS-U/I cards the Concentration channel will always be: internal-13 --for MP-2200 HS-S12, HS-S6, HS-U12, HS-U6 and DXC HS-U8 and HS-U16 cards, the Concentration channel is selected via the prtInHsiConcentratedTo object. notConnected - same as prtInHsiConnect=no.
INT prtInHsiSltIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted.
prtInLs2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.4.2.1		not-accessible	An entry in table.
I32 prtInLs2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtInLs2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.4.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtInLs2Connect	1.3.6.1.4.1.164.3.2.3.2.4.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel.
INT prtInLs2EnvAssign	1.3.6.1.4.1.164.3.2.3.2.4.2.1.8	INTEGER	read-write	Envelope assignment type.
I32 prtInLs2Group	1.3.6.1.4.1.164.3.2.3.2.4.2.1.5	Integer32	read-write	This attribute indicates the group number of the port. LS-2 internal ports with the same group number share the same Time slot of the main link
INT prtInLs2LinkTo	1.3.6.1.4.1.164.3.2.3.2.4.2.1.7	INTEGER	read-write	It indicates the slot of the main link card to which the LS2 card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
I32 prtInLs2Member	1.3.6.1.4.1.164.3.2.3.2.4.2.1.6	Integer32	read-write	This attribute indicates the group member id of the port. This parameter is for the automatic envelope assignment algorithm.
INT prtInLs2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port index.
INT prtInLs2SltIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
prtInLs6CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.3.1		not-accessible	An entry in table.
I32 prtInLs6CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtInLs6CnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtInLs6Connect	1.3.6.1.4.1.164.3.2.3.2.13.3.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel.
INT prtInLs6LinkTo	1.3.6.1.4.1.164.3.2.3.2.13.3.1.8	INTEGER	read-write	It indicates the slot of the main link card to which the Ls6 card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - when prtInLs6TandemMode=tandemSlave. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInLs6PrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.3	INTEGER	read-only	This attribute indicates a unique internal port index.
INT prtInLs6Rate	1.3.6.1.4.1.164.3.2.3.2.13.3.1.6	INTEGER	read-write	Main Rate in Kbps.
INT prtInLs6RemoteType	1.3.6.1.4.1.164.3.2.3.2.13.3.1.7	INTEGER	read-write	Remote Type. notApplicable - when prtInLs6TandemMode=tandemSlave
INT prtInLs6SltIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtInLs6TandemMode	1.3.6.1.4.1.164.3.2.3.2.13.3.1.5	INTEGER	read-write	This object indicates the Tandem Mode. tandemSlave - is valid only for an LS-6 card having on the (current slot-1) an LS-6 card with 'tandemMaster' mode.
prtInMbeCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.11.2.1		not-accessible	An entry in table.
I32 prtInMbeCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtInMbeCnfgTable	1.3.6.1.4.1.164.3.2.3.2.11.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtInMbeConnect	1.3.6.1.4.1.164.3.2.3.2.11.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInMbeLinkTo	1.3.6.1.4.1.164.3.2.3.2.11.2.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInMbePrtIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtInMbeRate	1.3.6.1.4.1.164.3.2.3.2.11.2.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInMbeSltIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtInPh1MlAssociatedExCh	1.3.6.1.4.1.164.3.2.3.2.2.3.1.20	INTEGER	read-write	This object indicates the external port associated to this internal port. At present, it is used by the Hybrid (mp2100h), MHS-4 cards which can have up to 64 dynamic internal ports associated with External ports. For ISDN cards, the value will be: notApplicable (255). The associated external of an ISDN internal port is represented by the MIB object: prtIsdnDirectoryPrtNu.
INT prtInPh1MlBearerCh	1.3.6.1.4.1.164.3.2.3.2.2.3.1.19	INTEGER	read-write	Defines which B (bearer) channels are used for transferring ISDN data. Default value is: none (255). anyChannel (2) is skipped because it is not in use here.
INT prtInPh1MlCcittCrc	1.3.6.1.4.1.164.3.2.3.2.2.3.1.23	INTEGER	read-write	This object indicates how many Bits are used for CRC (HDLC item).
INT prtInPh1MlClockEncoding	1.3.6.1.4.1.164.3.2.3.2.2.3.1.21	INTEGER	read-write	This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols.
prtInPh1MlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.3.1		not-accessible	An entry in table.
I32 prtInPh1MlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtInPh1MlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
I32 prtInPh1MlCongLevel	1.3.6.1.4.1.164.3.2.3.2.2.3.1.9	Integer32	read-write	This attribute indicates the level of delayed data in precents of the total available dynamic memory, for which the port will start to operate . The resolution of the parameter is 5 percent. Valid values: 10..70, 255. 255=notApplicable.
INT prtInPh1MlCongResponse	1.3.6.1.4.1.164.3.2.3.2.2.3.1.8	INTEGER	read-write	This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/receive becn to/from the network). no - do nothing FlowControl - translate the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done in both directions.
INT prtInPh1MlConnect	1.3.6.1.4.1.164.3.2.3.2.2.3.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInPh1MlConnectionTyp	1.3.6.1.4.1.164.3.2.3.2.2.3.1.7	INTEGER	read-write	This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management operation (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetNotMana - indicates network internal line, but the remote mux is not managed by the nms. User - User to Network Interface. OtherNet - Network To Network Interfce. PubNet - Access Mux To PubNet Interface.
I32 prtInPh1MlDlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtInPh1MlDlciEntry	1.3.6.1.4.1.164.3.2.3.2.2.4.1		not-accessible	An entry in table.
I32 prtInPh1MlDlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.2.4.1.8	Integer32	read-write	This attribute indicates a unique internal connection dlci number which the src dlci is routed to.
INT prtInPh1MlDlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.2.4.1.7	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to.
INT prtInPh1MlDlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.2.4.1.6	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid
I32 prtInPh1MlDlciIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, then its type is 'user' and the only valid index is 1.
I32 prtInPh1MlDlciPriority	1.3.6.1.4.1.164.3.2.3.2.2.4.1.13	Integer32	read-write	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority.
INT prtInPh1MlDlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. MPH.1/E1 and MPH.1/T1 cards have three internal ports.
INT prtInPh1MlDlciRxBc	1.3.6.1.4.1.164.3.2.3.2.2.4.1.11	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line.
INT prtInPh1MlDlciRxBe	1.3.6.1.4.1.164.3.2.3.2.2.4.1.12	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line.
INT prtInPh1MlDlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtInPh1MlDlciStatus	1.3.6.1.4.1.164.3.2.3.2.2.4.1.14	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
prtInPh1MlDlciTable	1.3.6.1.4.1.164.3.2.3.2.2.4		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtInPh1MlDlciTxBc	1.3.6.1.4.1.164.3.2.3.2.2.4.1.9	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line.
INT prtInPh1MlDlciTxBe	1.3.6.1.4.1.164.3.2.3.2.2.4.1.10	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line.
INT prtInPh1MlDlciValid	1.3.6.1.4.1.164.3.2.3.2.2.4.1.5	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
I32 prtInPh1MlEnqPeriod	1.3.6.1.4.1.164.3.2.3.2.2.3.1.14	Integer32	read-write	This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlErrorsThreshold	1.3.6.1.4.1.164.3.2.3.2.2.3.1.17	Integer32	read-write	This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
INT prtInPh1MlFlowControl	1.3.6.1.4.1.164.3.2.3.2.2.3.1.11	INTEGER	read-write	This attribute indicates the required flow control betweeen the port and the remote equipment.
INT prtInPh1MlFrameSeparator	1.3.6.1.4.1.164.3.2.3.2.2.3.1.24	INTEGER	read-write	This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line.
INT prtInPh1MlFrMngProt	1.3.6.1.4.1.164.3.2.3.2.2.3.1.13	INTEGER	read-write	This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtInPh1MlConnectionTyp = sameNetManaged, this object will be RO (internally determined).
I32 prtInPh1MlFrWindowSize	1.3.6.1.4.1.164.3.2.3.2.2.3.1.16	Integer32	read-write	This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlFullRptPeriod	1.3.6.1.4.1.164.3.2.3.2.2.3.1.15	Integer32	read-write	This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite (never sent). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.2.3.1.18	Integer32	read-write	Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=Never. Never move to higher prioritized connected link. UNIT is seconds. Valid values are: 0, 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 120, 180, 240, 300, 360, 420, 480, 540, 600, 900, 1200, 1500, 1800. Attempt to Set an invalid value will result in getting the default value.
I32 prtInPh1MlMinSeparators	1.3.6.1.4.1.164.3.2.3.2.2.3.1.22	Integer32	read-write	Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable
INT prtInPh1MlProtocol	1.3.6.1.4.1.164.3.2.3.2.2.3.1.6	INTEGER	read-write	This attribute indicates the applied protocol.
I32 prtInPh1MlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.3.1.3	Integer32	read-only	This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have three internal interfaces. MX3000 modules may have up to 50 internal ports.
INT prtInPh1MlRate	1.3.6.1.4.1.164.3.2.3.2.2.3.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInPh1MlSegment	1.3.6.1.4.1.164.3.2.3.2.2.3.1.12	INTEGER	read-write	This object is the Segmentation in Bytes. In protocol FR+, ISDN internals, MX 30/300 the segmentation is: 50 (2) ,158 (3) ,266 (4) ,376 (5), 484 (6) In MX 3000/4: For protocol FR+ (internal ISDN ports of MHS.S, MHS.U, MHS.E1, MHS.T1 cards) segmentation values are: 236 (7),472 (8), 708 (9), 944 (10) ,1180 (11)
INT prtInPh1MlSltType	1.3.6.1.4.1.164.3.2.3.2.2.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For ISDN BRI port of MX300/30: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtInPh1MlTc	1.3.6.1.4.1.164.3.2.3.2.2.3.1.10	INTEGER	read-write	This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports in the specific card. 255=notApplicable.
prtInTreCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.12.2.1		not-accessible	An entry in table.
I32 prtInTreCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtInTreCnfgTable	1.3.6.1.4.1.164.3.2.3.2.12.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtInTreConnect	1.3.6.1.4.1.164.3.2.3.2.12.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInTreLinkTo	1.3.6.1.4.1.164.3.2.3.2.12.2.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInTrePrtIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtInTreRate	1.3.6.1.4.1.164.3.2.3.2.12.2.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInTreSltIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
prtInVc3CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.14.2.1		not-accessible	An entry in table.
I32 prtInVc3CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtInVc3CnfgTable	1.3.6.1.4.1.164.3.2.3.2.14.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtInVc3Connect	1.3.6.1.4.1.164.3.2.3.2.14.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInVc3LinkTo	1.3.6.1.4.1.164.3.2.3.2.14.2.1.7	INTEGER	read-write	This attribute indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInVc3Oos	1.3.6.1.4.1.164.3.2.3.2.14.2.1.6	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
INT prtInVc3PrtIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtInVc3Rate	1.3.6.1.4.1.164.3.2.3.2.14.2.1.5	INTEGER	read-write	Rate in bps.
INT prtInVc3SltIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
prtIP	1.3.6.1.4.1.164.6.2.15.6
I32 prtIpParamAgingTime	1.3.6.1.4.1.164.6.2.15.6.1.1.19	Integer32	read-write	Aging Time in seconds.
U32 prtIpParamBurstSize	1.3.6.1.4.1.164.6.2.15.6.1.1.32	Unsigned32	read-write	The burst size that the port can support beyond rate limitation determined in prtIpParamRateLimit. Burst Size is measured in bytes.
I32 prtIpParamConfigIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.1	Integer32	read-only	This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). For products having Agent and Edit configurations, Write operation for the table entries is allowed only to Config=255.
INT prtIpParamConnect	1.3.6.1.4.1.164.6.2.15.6.1.1.18	INTEGER	read-write	Port Connection.
IP prtIpParamDefaultGateway	1.3.6.1.4.1.164.6.2.15.6.1.1.6	IpAddress	read-write	Default Gateway's IP Address.
I32 prtIpParamDefInterface	1.3.6.1.4.1.164.6.2.15.6.1.1.29	Integer32	read-write	The Default Interface for packets with unresolved destination subnet. For internal-X port: 100 + X .
I32 prtIpParamDoubleTagVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.25	Integer32	read-write	VLAN Identifier of the Double Tagging VLAN.
I32 prtIpParamDoubleTagVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.26	Integer32	read-write	VLAN Frame priority of the Double Tagging VLAN.
I32 prtIpParamEncapProtPort	1.3.6.1.4.1.164.6.2.15.6.1.1.21	Integer32	read-write	Encapsulation Protocol Port (TCP/UDP Port).
INT prtIpParamEncapsulationProt	1.3.6.1.4.1.164.6.2.15.6.1.1.20	INTEGER	read-write	Encapsulation Protocol.
prtIpParamEntry	1.3.6.1.4.1.164.6.2.15.6.1.1		not-accessible	An entry in table.
I32 prtIpParamFloodedRateLimit	1.3.6.1.4.1.164.6.2.15.6.1.1.31	Integer32	read-write	The maximum rate permitted to transfer broadcast, multicast, and unicast flooded frames via this port, in Kbps. 0 - Disable. In Ipmux14 this parameter is applicable when prtIpParamRateLimit=0 (disable).
IP prtIpParamHostIP	1.3.6.1.4.1.164.6.2.15.6.1.1.4	IpAddress	read-write	The host interface IP address.
IP prtIpParamHostMask	1.3.6.1.4.1.164.6.2.15.6.1.1.5	IpAddress	read-write	The host interface subnet mask.
I32 prtIpParamIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.3	Integer32	read-only	This object indicates a unique Port Index.
I32 prtIpParamKeepAliveInterval	1.3.6.1.4.1.164.6.2.15.6.1.1.34	Integer32	read-write	This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
I32 prtIpParamKeepAliveThresh	1.3.6.1.4.1.164.6.2.15.6.1.1.35	Integer32	read-write	This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
INT prtIpParamLimitPacketType	1.3.6.1.4.1.164.6.2.15.6.1.1.33	INTEGER	read-write	The packet type that will be rate limited. Rate limitation determined in prtIpParamRateLimit. all - All packet types are rate limited. broadMultiFloodedUnicast - Broadcast, Multicast and Flooded Unicast packets are rate limited. broadcastMulticast - Broadcast and Multicast packets are rate limited. broadcast - Broadcast packets are rate limited.
INT prtIpParamMaxTxBandwidth	1.3.6.1.4.1.164.6.2.15.6.1.1.16	INTEGER	read-write	This object shows the Max Bandwidth allowed on the LAN. Full - means that a Maximum of 100 Mega Byte Rate may go through the LAN. e1(3) means that the maximum is an E1 rate. t1(4) is for a maximum of a T1 rate.
INT prtIpParamMediaMode	1.3.6.1.4.1.164.6.2.15.6.1.1.7	INTEGER	read-only	This object indicates the real Media Mode.
INT prtIpParamMediaRate	1.3.6.1.4.1.164.6.2.15.6.1.1.8	INTEGER	read-only	This object indicates the real Media Rate (Mbps).
INT prtIpParamMng	1.3.6.1.4.1.164.6.2.15.6.1.1.30	INTEGER	read-write	This object indicates whether Management is enabled/disabled via this port.
I32 prtIpParamMngVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.10	Integer32	read-write	Management VLAN ID.
I32 prtIpParamMngVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.11	Integer32	read-write	Management VLAN Frame priority.
INT prtIpParamMngVlanSupport	1.3.6.1.4.1.164.6.2.15.6.1.1.9	INTEGER	read-write	Management VLAN support (Tagging). no - No support of VLAN Tagging. yes - 4 VLAN bytes will be added to the frame.
I32 prtIpParamP2pKeepAliveVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.36	Integer32	read-write	Dedicated VLAN ID for keep alive messages.
I32 prtIpParamP2pKeepAliveVlanPrio	1.3.6.1.4.1.164.6.2.15.6.1.1.37	Integer32	read-write	VLAN priority for P2P keep alive messages .
INT prtIpParamProtIpEnable	1.3.6.1.4.1.164.6.2.15.6.1.1.13	INTEGER	read-write	This object indicates whether a list of Protected IP Addresses is enabled or not. This object is applicable only if prtIpParamRingMode=enable.
I32 prtIpParamRateLimit	1.3.6.1.4.1.164.6.2.15.6.1.1.28	Integer32	read-write	The maximum rate permitted to transfer via this port, in Kbps.
IP prtIpParamRemoteIP	1.3.6.1.4.1.164.6.2.15.6.1.1.15	IpAddress	read-write	This is the IP Address of the remote device that is connected to the current device (Point to Point Application). It is used for sending OAM packets on the LAN to the remote side in order to check that the connection is OK.
MAC prtIpParamRingAdjacentMacAddr	1.3.6.1.4.1.164.6.2.15.6.1.1.38	MacAddress	read-only	The MAC address of the adjacent NE connected to this port in an ETH ring. If the port is not a member of a ring, the value of this parameter will be 00-00-00-00-00-00.
INT prtIpParamRingMode	1.3.6.1.4.1.164.6.2.15.6.1.1.12	INTEGER	read-write	This object indicates If Ring Mode is enabled or not.
I32 prtIpParamSlotIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.2	Integer32	read-only	This object indicates a unique number of the slot position in which the module is inserted. notApplicable = 255 (for products that don't have slots). For KM: kmxMlA (103), kmxMlB (104).
prtIpParamTable	1.3.6.1.4.1.164.6.2.15.6.1		not-accessible	A table - Parameters for IP Ports.
I32 prtIpParamTos	1.3.6.1.4.1.164.6.2.15.6.1.1.17	Integer32	read-write	TOS = Type of Service transmitted. Valid values: 0..255.
INT prtIpParamTrafficPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.14	INTEGER	read-write	This object indicates the traffic priority of this port.
I32 prtIpParamVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.23	Integer32	read-write	VLAN Identifier.
I32 prtIpParamVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.24	Integer32	read-write	VLAN Frame priority.
INT prtIpParamVlanSupport	1.3.6.1.4.1.164.6.2.15.6.1.1.22	INTEGER	read-write	VLAN support (Tagging). 'no' - No support of VLAN Tagging. 'yes' - 4 VLAN bytes will be added to the frame.
INT prtIpParamVlanTagging	1.3.6.1.4.1.164.6.2.15.6.1.1.27	INTEGER	read-write	VLAN Tagging. 'unmodified' - No change will be done to the Frame. 'tag' - Add Tag to Untagged Frames. 'doubleTag' - Add Tag to all Frames. 'doubleTagAndFallBack' - Double Tagging will have different rules for VLANs that this port is member in, than these it is not a member in. 'untag' - Remove Tag from tagged frames.
INT prtIRate	1.3.6.1.4.1.164.3.3.3.6.1.1.3	INTEGER	read-write	This object indicates the port rate in bits. Each TS contains 8 bits. Thus, 1 bit is equivalent to 8Kbps rate.
INT prtIsdnAbSide	1.3.6.1.4.1.164.3.2.3.2.16.1.1.12	INTEGER	read-write	This parameter indicates the QSIG side in layer 3. This definition is from the QSIG Standard.
INT prtIsdnBasicRateLineTopology	1.3.6.1.4.1.164.3.2.3.2.16.1.1.6	INTEGER	read-write	This attribute is relevant for ISDN BRI only. It is equivalent to isdnBasicRateLineTopology in the isdn MIB.
I32 prtIsdnCallBackTimeout	1.3.6.1.4.1.164.3.2.3.2.16.1.1.16	Integer32	read-write	This object is applicable only if 'prtIsdnFilter' is 'CallBack' and determines how long to wait from receiving the incoming call until initiating the call back call. The vaules range should be '1..20 sec' and the default 10 sec.
INT prtIsdnCallMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.15	INTEGER	read-write	This object indicates the acceptance of incoming calls. Initiate - Callout Listen - Callin.
prtIsdnCnfg	1.3.6.1.4.1.164.3.2.3.2.16
prtIsdnCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.16.1.1		not-accessible	An entry in table.
I32 prtIsdnCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtIsdnCnfgTable	1.3.6.1.4.1.164.3.2.3.2.16.1		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
INT prtIsdnConnect	1.3.6.1.4.1.164.3.2.3.2.16.1.1.4	INTEGER	read-write	This attribute indicates if the port is connected.
I32 prtIsdnDirectoryCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtIsdnDirectoryEntry	1.3.6.1.4.1.164.3.2.3.2.16.3.1		not-accessible	An entry in table.
STR prtIsdnDirectoryLocalAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.4	DisplayString	read-create	This is the local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryLocalAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.11	DisplayString	read-create	This is the second local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryLocalSubAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.5	DisplayString	read-create	This is the local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
STR prtIsdnDirectoryLocalSubAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.12	DisplayString	read-create	This is the second local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
I32 prtIsdnDirectoryPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.3	Integer32	read-only	For MAXcess this is the internal port number: 101, 102,.... For KM-2100 the port index is calculated as follows: 100*Slot+Ch
I32 prtIsdnDirectoryPrtNu	1.3.6.1.4.1.164.3.2.3.2.16.3.1.8	Integer32	read-create	This is the external port number connected to this entry.
STR prtIsdnDirectoryRemoteAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.6	DisplayString	read-create	This is the remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryRemoteAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.13	DisplayString	read-create	This is the second remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank(20 characters)
STR prtIsdnDirectoryRemoteSubAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.7	DisplayString	read-create	This is the remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
STR prtIsdnDirectoryRemoteSubAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.14	DisplayString	read-create	This is the second remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
ROW prtIsdnDirectoryRowStatus	1.3.6.1.4.1.164.3.2.3.2.16.3.1.10	RowStatus	read-create	This is the status for the row. It allows to know whether to consider this row or not. The only possible supported RowStatus vaules are active (1) and destroy (6).
INT prtIsdnDirectorySltIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For MX300/30 ports: io1(5) = isdn1(5) and io2(6) = isdn2(6). In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
prtIsdnDirectoryTable	1.3.6.1.4.1.164.3.2.3.2.16.3		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
I32 prtIsdnDirectoryTeiId	1.3.6.1.4.1.164.3.2.3.2.16.3.1.9	Integer32	read-create	This is the abstract terminal id if relevant, connected to this entry.
INT prtIsdnEndpointBearerCh	1.3.6.1.4.1.164.3.2.3.2.16.2.1.8	INTEGER	read-create	This is the selected dialing channel. anyChannel - the system selects the dialing channel.
I32 prtIsdnEndpointCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtIsdnEndpointEntry	1.3.6.1.4.1.164.3.2.3.2.16.2.1		not-accessible	An entry in table.
INT prtIsdnEndpointIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.4	INTEGER	read-only	Since more than one endpoint may be defined per isdn entity, this field is a simple index. It corresponds to isdnEndpointIdx in the isdn MIB.
I32 prtIsdnEndpointPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.3	Integer32	read-only	This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch
ROW prtIsdnEndpointRowStatus	1.3.6.1.4.1.164.3.2.3.2.16.2.1.9	RowStatus	read-create	This field indicates whether to consider this endpoint or not. The only possible supported RowStatus vaules are active (1) and destroy (6).
INT prtIsdnEndpointSltIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
STR prtIsdnEndpointSpid	1.3.6.1.4.1.164.3.2.3.2.16.2.1.7	DisplayString	read-create	The Service profile IDentifier (SPID) information for this Terminal Endpoint. It is is composed of 9-20 numeric characters. It corresponds to isdnEndpointSpid in the isdn MIB.
prtIsdnEndpointTable	1.3.6.1.4.1.164.3.2.3.2.16.2		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
INT prtIsdnEndpointTeiType	1.3.6.1.4.1.164.3.2.3.2.16.2.1.5	INTEGER	read-create	The type of TEI (Terminal Endpoint Identifier) used for this Terminal Endpoint. In case of dynamic(1), the TEI value is selected by the switch. In case of static(2), a valid TEI value has to be entered in the isdnEndpointTeiValue object. interface type as well as the Terminal Endpoint type. static(2). On Basic Rate interfaces the default value is dynamic(1) for isdn(63) Terminal Endpoints. It corresponds to isdnEndpointTeiType in the isdn MIB.
I32 prtIsdnEndpointTeiValue	1.3.6.1.4.1.164.3.2.3.2.16.2.1.6	Integer32	read-create	When the TEI Type is static, the value of the TEI should be between 0 and 63. Else, it is not selectable by user. 255 = notApplicable. It corresponds to isdnEndpointTeiValue in the isdn MIB
INT prtIsdnFilter	1.3.6.1.4.1.164.3.2.3.2.16.1.1.8	INTEGER	read-write	This attribute allows the user to configure the port: answerAll(2): accept all incoming calls, rejectAll(3): reject all incoming calls, selective(4): accept or reject according directory table. callBack (5): In this mode the ISDN Ch will reject incoming calls and will initiate call back to the rejected phone number.
INT prtIsdnInterface	1.3.6.1.4.1.164.3.2.3.2.16.1.1.14	INTEGER	read-write	It indicates the interface type: lt = line termination nt = network termination te = terminal equipment.
INT prtIsdnMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.7	INTEGER	read-write	This attribute allows the user to configure the port as leased(2) in case of connection to a TDM network.
I32 prtIsdnNumOfAbstractTerm	1.3.6.1.4.1.164.3.2.3.2.16.1.1.10	Integer32	read-write	An object for KM2100/4 agents. 255=Not Applicable When ISDN Standard = ETSI or NTT (European) the value should be 255 (NotApplicable) else If ML speed is 64Kbps value should be 1. If ML speed is 128Kbps value can be either 1 or 2 (user selection).
I32 prtIsdnPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.3	Integer32	read-only	This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch
INT prtIsdnQsigRole	1.3.6.1.4.1.164.3.2.3.2.16.1.1.13	INTEGER	read-write	This parameter indicates the QSIG side in layer 1 & 2.
INT prtIsdnSignalingProtocol	1.3.6.1.4.1.164.3.2.3.2.16.1.1.5	INTEGER	read-write	This attribute fixes which signaling protocol is used at this port (D-Channel). It is equivalent to isdnSignalingProtocol in the isdn MIB.
INT prtIsdnSimultaneousCall	1.3.6.1.4.1.164.3.2.3.2.16.1.1.9	INTEGER	read-write	In case of simultaneous call (local,remote and remote,local): accept(2): accept the incoming call, reject(3): reject the incoming call.
INT prtIsdnSltIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
INT prtIsdnStatusCallDirection	1.3.6.1.4.1.164.3.2.3.1.16.1.6	INTEGER	read-only	Attribute indicating the Direction of the Call. The value of notApplicable will be used for example when prtIsdnStatusCallState = notActive(14).
IP prtIsdnStatusCalledIP	1.3.6.1.4.1.164.3.2.3.1.16.1.5	IpAddress	read-only	This is the remote IP Address associated with this entry.
STR prtIsdnStatusCalledNumber	1.3.6.1.4.1.164.3.2.3.1.16.1.4	DisplayString	read-only	This is the remote Number (ISDN Address) associated with this entry.
STR prtIsdnStatusCallingNumber	1.3.6.1.4.1.164.3.2.3.1.16.1.3	DisplayString	read-only	This is the local Number (ISDN Address) associated with this entry.
INT prtIsdnStatusCallState	1.3.6.1.4.1.164.3.2.3.1.16.1.2	INTEGER	read-only	The state that the current call is in.
INT prtIsdnStatusDspMode	1.3.6.1.4.1.164.3.2.3.1.16.1.1	INTEGER	read-only	The DSP can be in one of the following Modes: Voice, Idle, Fax, Voice Band Data (VBD)- Modem.
prtIsdnStatusEntry	1.3.6.1.4.1.164.3.2.3.1.16.1		not-accessible	Entries for ISDN Statistics parameters that do not appear in the standard MIBs or for agents that don't support the standard Index of Call Set Up Time.
prtIsdnStatusTable	1.3.6.1.4.1.164.3.2.3.1.16		not-accessible	This table contains ISDN Statistics parameters that do not appear in the standard MIBs or for agents that don't support the standard Index of Call Set Up Time.
INT prtIsdnSwitchMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.11	INTEGER	read-write	For KM2100. auto - The call is initiated automatically by one of the IO cards connected to KML.10(ISDN card) having ISDN Switch Mode. manual - The call is initiated by the user manually, for KML.10 having ISDN Switch Mode (via mdlSCmd). connect- The call is initiated 'immediately', for KML.10 having ISDN Switch Mode. 'immediately'- means: immediately after power-up (when product performed Reset) OR, since this value appears in the active configuration. In this case, the call can be disconnected only by power-off of the product or by changing this object to another value (or actual Remove of the KML.10 relevant card). notApplicable - For other card types.
prtLanWanCnfg	1.3.6.1.4.1.164.3.2.3.2.22
prtLanWanCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.22.1.1		not-accessible	An entry in table.
I32 prtLanWanCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
prtLanWanCnfgTable	1.3.6.1.4.1.164.3.2.3.2.22.1		not-accessible	This is a table for Lan-Wan port parameters.
I32 prtLanWanDestIf	1.3.6.1.4.1.164.3.2.3.2.22.1.1.5	Integer32	read-write	This object determines the Destination Interface for the frames received by this port. - Switching Table = 100 (it means that the destination interface will be determined by the Switching Table) - inPrtX (internal-X port): 100 + X . For FCD-155 this object is not applicable =0
INT prtLanWanEgressVlanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.6	INTEGER	read-write	This object determines what to do with the VLAN frames that exit via the WAN side of the port. This object is not applicable when prtLanWanMode=l3SubnetSwitch(4).
INT prtLanWanL2Protocol	1.3.6.1.4.1.164.3.2.3.2.22.1.1.7	INTEGER	read-write	L2 Protocol. When prtLanWanMode=l3SubnetSwitch(4), the only valid value is ppp(3).
INT prtLanWanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.4	INTEGER	read-write	This object determines the working mode of this port. For FCD155, layer3SubnetSwitch is not applicable
I32 prtLanWanMtu	1.3.6.1.4.1.164.3.2.3.2.22.1.1.13	Integer32	read-write	The size of the largest packet which can be sent/received on the interface, specified in octets. Valid values change per device. 0=not applicable.
I32 prtLanWanPrtIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.3	Integer32	not-accessible	This object indicates a unique number to identify a port in a specific card. Generally, for MP-210X/2200, the Port Index will be according to the external/internal port number: - exPrtX : X - inPrtX : 100 + X For FCD-155, refer to device specification
INT prtLanWanSltIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.2	INTEGER	not-accessible	This object indicates a unique slot position where the module is inserted.
I32 prtLanWanStpCost	1.3.6.1.4.1.164.3.2.3.2.22.1.1.9	Integer32	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
I32 prtLanWanStpPriority	1.3.6.1.4.1.164.3.2.3.2.22.1.1.8	Integer32	read-write	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID.
INT prtLanWanToLanVlanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.10	INTEGER	read-write	This object determines what to do with the VLAN frames that come from WAN side of the port and exit towards one of the LAN ports. This object is applicable only when prtLanWanDestIf=100 or 101 (Switching Table or inPrt1).
I32 prtLanWanVlanId	1.3.6.1.4.1.164.3.2.3.2.22.1.1.11	Integer32	read-write	This is the VLAN Id attached to a frame, when the relevant Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is tag or doubleTag. 0=not applicable.
I32 prtLanWanVlanPriority	1.3.6.1.4.1.164.3.2.3.2.22.1.1.12	Integer32	read-write	This is the VLAN Priority attached to a frame, when the relevant Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is tag or doubleTag. Valid values: 0..7 255=not applicable.
INT prtLanWanVlanType	1.3.6.1.4.1.164.3.2.3.2.22.1.1.14	INTEGER	read-write	This oject indicates type of VLAN this port is assigned to. Port Base Vlan parameters are defined by objects under radBridgePortBaseVlan
prtLogicalCnfg	1.3.6.1.4.1.164.3.2.3.2.17
prtLogicalCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.17.1.1		not-accessible	An entry in table.
I32 prtLogicalCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtLogicalCnfgTable	1.3.6.1.4.1.164.3.2.3.2.17.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtLogicalConnect	1.3.6.1.4.1.164.3.2.3.2.17.1.1.4	INTEGER	read-create	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtLogicalFunction	1.3.6.1.4.1.164.3.2.3.2.17.1.1.5	INTEGER	read-create	This parameter defines the function of the relevant channel.
I32 prtLogicalPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be an internal port number: inPrt1(101)->inPrt50(150), linkSel1(200)->linkSel50(250), encaps1(300)-> encaps50(350), huntGr1(101) -> huntGr10(110).
ROW prtLogicalRowStatus	1.3.6.1.4.1.164.3.2.3.2.17.1.1.6	RowStatus	read-create	This parameter allows the NMS to create/delete logical ports. The only possible supported RowStatus vaules are active (1) and destroy (6).
INT prtLogicalSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.2	INTEGER	read-only	Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
prtLs2Cnfg	1.3.6.1.4.1.164.3.2.3.2.4
prtLs6Cnfg	1.3.6.1.4.1.164.3.2.3.2.13
prtMbeCnfg	1.3.6.1.4.1.164.3.2.3.2.11
INT prtMl4CGA	1.3.6.1.4.1.164.3.2.3.2.19.1.1.5	INTEGER	read-write	This object selects the method used to signal the CGA state to the other end, through the main link. 'none' - non-transparent mode. When one of the links (main) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos' will be transmitted to the other end. 'trans' - when one of the links (main) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos' will be transmitted to the other end.
prtMl4Cnfg	1.3.6.1.4.1.164.3.2.3.2.19
prtMl4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.19.1.1		not-accessible	An entry in table.
I32 prtMl4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
prtMl4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.19.1		not-accessible	This is an extension table for MTML-4 card parameters.
INT prtMl4CrossConnectLevel	1.3.6.1.4.1.164.3.2.3.2.19.1.1.20	INTEGER	read-write	This object indicates whether the cross connect is on DS1 or DS0 (time-slots) level. When cross connect level is ds1, Destination Slot is indicated by prtGenCnfgLinkToSlot, Destination Port is indicated by prtGenCnfgLinkToPort. For Unframed Line Type, cross connect level can be either notApplicable (NC=not connected) or DS1. Otherwise, default value is ds0.
OCT prtMl4DataOos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.8	OCTET STRING	read-write	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
I32 prtMl4DedicatedTs	1.3.6.1.4.1.164.3.2.3.2.19.1.1.18	Integer32	read-write	A unique number to identify Dedicated TS of the E1 port (V5.2). It is applicable only when prtMl4Service=v52Slave and prtExPh1MlInbandMng selected is dedicatedTs, dedicatedPpp or dedicatedFr. 1..31 - Dedicated TS of E1 255 - notApplicable Other values are invalid.
INT prtMl4EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.19.1.1.13	INTEGER	read-write	Echo canceler activation.
IP prtMl4IpAddress	1.3.6.1.4.1.164.3.2.3.2.19.1.1.10	IpAddress	read-write	IP Address of the port.
IP prtMl4IpMask	1.3.6.1.4.1.164.3.2.3.2.19.1.1.11	IpAddress	read-write	IP subnet mask of the port.
I32 prtMl4LogicalLinkId	1.3.6.1.4.1.164.3.2.3.2.19.1.1.17	Integer32	read-write	This object defines for a V5.2 Master ML the Logical Link Id. Valid values are: 0..256. NA=257.
INT prtMl4Oos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.6	INTEGER	read-write	'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0
I32 prtMl4OosEntryThreshold	1.3.6.1.4.1.164.3.2.3.2.19.1.1.15	Integer32	read-write	This object defines the number of Errors per Second that determine the minimum unacceptable noise level. This value will be the Entry Threshold to the OOS (Out-of-Service) state. This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable.
INT prtMl4OosErrorSource	1.3.6.1.4.1.164.3.2.3.2.19.1.1.14	INTEGER	read-write	OOS (Out-of-Service) Error Source. This object is applicable for T1 ports only.
I32 prtMl4OosExitThreshold	1.3.6.1.4.1.164.3.2.3.2.19.1.1.16	Integer32	read-write	This object defines the number of consecutive Error-Free-Seconds before going from OOS state to Normal state. This value will be the Exit Threshold from the OOS (Out-of-Service) state. Units=seconds This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable.
INT prtMl4PppEchoFailDetection	1.3.6.1.4.1.164.3.2.3.2.19.1.1.21	INTEGER	read-write	This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Disable. Enable - will be selected mainly when a T1/E1 Ring exists and between 2 adjacent Ring devices there is another device or Net, that causes these Ring devices not to sense that the PPP connection between them is lost. In this case, Echo Request should be initiated by the port.
INT prtMl4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtMl4RemCrc	1.3.6.1.4.1.164.3.2.3.2.19.1.1.19	INTEGER	read-write	This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.
INT prtMl4Service	1.3.6.1.4.1.164.3.2.3.2.19.1.1.9	INTEGER	read-write	Link Service. leasedLine - usual TDM interface. v51 - V5.1 interface. v52Master - V5.2 Link to Local Exchange. v52Slave - a ML that is transferred to the v52Master.
INT prtMl4SignalingMode	1.3.6.1.4.1.164.3.2.3.2.19.1.1.12	INTEGER	read-write	Refers to the signaling mode of the port (or framer module). notApplicable(1)- means that no framer is needed for this port (no signaling), or that this object is not relevant. cas(2) means Channel Associated Signaling. Used for E1 Links. ccs(3) is the Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). robbedBit(4) is a method implementing 7 bits for the voice and 1 bit dedicated for signaling. Used for T1 Links. other (5)- Signaling generally exists though not specifically according to one of the values listed ; this port uses a framer in this case.
INT prtMl4SigProfile	1.3.6.1.4.1.164.3.2.3.2.19.1.1.4	INTEGER	read-write	This object indicates the Signaling Profile of the port. none - when the Frame is G732N (no MF) or Unframed. p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5 perTS = when Signaling Profile is selected per TS.
INT prtMl4SltIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
OCT prtMl4VoiceOos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.7	OCTET STRING	read-write	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
I32 prtMonCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.6.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. For products that do not support configurations, 1 will be always used.
prtMonEntry	1.3.6.1.4.1.164.3.3.3.1.6.1		not-accessible	An entry in table.
I32 prtMonitoredPort	1.3.6.1.4.1.164.3.3.3.1.6.1.5	Integer32	read-write	This object indicates the MONITORED Port Index that the Monitoring port monitors. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * 100 - no port monitored For Optimux-T3: The valid channels are: 0 = no Ch monitored 1..21 or 1..28 (=CH1..CH21 or CH1..CH28) according to product's configuration.
OCT prtMonitoredTSs	1.3.6.1.4.1.164.3.3.3.1.6.1.6	OCTET STRING	read-write	This object indicates which TSs of the Monitored port, should be monitored. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled.
INT prtMonitoringEnable	1.3.6.1.4.1.164.3.3.3.1.6.1.3	INTEGER	read-write	This object indicates if the prtMonitoringIdx is configured as a monitoring port or not. disabled = the port is NOT configured to monitor. Setting this object to this value will cause reset (to 0) of the prtMonitoringTSs and prtMonitoredTSs objects. enabled = the port IS configured to monitor. For Optimux-T3: always enabled (RO supported).
I32 prtMonitoringIdx	1.3.6.1.4.1.164.3.3.3.1.6.1.2	Integer32	read-only	This object indicates the Monitoring Port Index. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Optimux-T3: 255 (Not Applicable) will be always used. The Monitoring port is always the Station Clock (not considered an interface).
OCT prtMonitoringTSs	1.3.6.1.4.1.164.3.3.3.1.6.1.4	OCTET STRING	read-write	This object indicates which TSs of the Monitoring port, the test equipment should monitor. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled.
prtMonTable	1.3.6.1.4.1.164.3.3.3.1.6		not-accessible	For DXC, the write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch).
prtMux	1.3.6.1.4.1.164.3.2.3
prtParam	1.3.6.1.4.1.164.6.2.15.5
OCT prtParamActUponLoopDetect	1.3.6.1.4.1.164.6.2.15.5.1.1.21	OCTET STRING	read-write	This parameter is used to indicate which actions should be taken in case a loop is detected in the network the port is part of. Each action is represented by a bit. Currently defined (for RIC155GE/RIC622GE): Bit 0 - Transmit Shut Down Bit 1 - Forward Alarms If bit value = '1' then the action is taken. If bit value = '0' then the actions is not taken.
INT prtParamAlarmIndication	1.3.6.1.4.1.164.6.2.15.5.1.1.13	INTEGER	read-only	This object indicates status-aggregation of non-masked alarms associated with all interface layers, related to this physical port. When at least one non-masked alarm exists on any layer, value of this object is on (3). Indication will be off (2) only when there's no active non-masked alarm on any interface layer related to this port. Masking an Alarm, will consider it as not exist for this indication. Example: When a port has an ATM higher layer and at least one VC has alarm, value of this object will be on (3)
INT prtParamClearAlarm	1.3.6.1.4.1.164.6.2.15.5.1.1.8	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Port Alarms. Upon completion, the value will automatically change to off(2).
OCT prtParamClkQualityLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.14	OCTET STRING	read-only	This parameter indicates quality level of clock signal. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows (when bit1=0): Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit)- Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization) 0001 PRS (=ST1 = Stratum 1 Traceable) 0111 ST2 (Stratum 2 Traceable) 1010 ST3 (Stratum 3 Traceable) 1100 SMC (SONET Minimum Clock Traceable) 1101 Stratum 3E Traceable bit1 = '1' - indicates all octet is Not Applicable
INT prtParamClkSrc	1.3.6.1.4.1.164.6.2.15.5.1.1.3	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' or 'loopback' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' or 'internal' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' or 'external' indicates that recovered receive clock from another card or interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'master' and 'fallback' values may be used RO to indicate active clock. 'station' - indicate clock received from station port is used as transmit clock.
INT prtParamClkSsmRxSource	1.3.6.1.4.1.164.6.2.15.5.1.1.24	INTEGER	read-write	This object indicates the Sa-bit of the E1 frame, in which SSM messages are carried.
OCT prtParamClkUserQualityLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.18	OCTET STRING	read-write	This parameter allows user to mark quality level of clock. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows: Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit) Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization)
INT prtParamClkWaveShape	1.3.6.1.4.1.164.6.2.15.5.1.1.15	INTEGER	read-write	Wave shape of station clock source signal.
U32 prtParamDataRate	1.3.6.1.4.1.164.6.2.15.5.1.1.19	Unsigned32	read-write	Rate of serial data port (V.11, V.24, V.35) in kbps units.
prtParamEntry	1.3.6.1.4.1.164.6.2.15.5.1.1		not-accessible	An entry in table.
U32 prtParamFarEndDevice	1.3.6.1.4.1.164.6.2.15.5.1.1.26	Unsigned32	read-write	Programmed Far-End device connected to this port. This object is relevant for products having multiple DBs. It will enable configuring offline, the relevant data. For MP-4100, LRS-102 OP-108/106 cards, the options will be: 1 = None (when a port is not connected to any remote device) 2 = OP-108 3 = OP-108/ETH 4 = OP-106 5 = OP-106/ETH 6 = card of MP or LRS-102
I32 prtParamIdx	1.3.6.1.4.1.164.6.2.15.5.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. For ACE2002: This parameter is the physical layer ifIndex of the slot on which the NMS requires the next interface index.
INT prtParamInterfaceType	1.3.6.1.4.1.164.6.2.15.5.1.1.7	INTEGER	read-write	The type of the port.
TIM prtParamLastResetStatsTime	1.3.6.1.4.1.164.6.2.15.5.1.1.6	TimeStamp	read-only	The value of MIB II's sysUpTime object at the last time that prtParamResetStatsCmd was Set to on(3) for this port. If prtParamResetStatsCmd was never Set to on(3) since last re-initialization of the agent, then this object contains a zero value. This object enables calculating the running time of Statistics counters for this port, by: [sysUpTime-prtParamLastResetStatsTime]. For some devices other types of 'Reset' may affect this parameter
OCT prtParamLeds	1.3.6.1.4.1.164.6.2.15.5.1.1.9	OCTET STRING	read-only	This entry specifies the LEDs status of the port. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
INT prtParamLineLength	1.3.6.1.4.1.164.6.2.15.5.1.1.10	INTEGER	read-write	Line Length of the line connected to this port.
INT prtParamLoopDetect	1.3.6.1.4.1.164.6.2.15.5.1.1.20	INTEGER	read-write	Enable/disable Loop Detection on a port. Examples of ports: physical, Channelized Bundle over TDM Uplink, Bridge Ports.
INT prtParamMappingMode	1.3.6.1.4.1.164.6.2.15.5.1.1.12	INTEGER	read-write	This object defines path protection on SONET/SDH link Auto - SONET/SDH mapping for port is copied automatically to same TU on the redundant SONET/SDH local (reside on same slot) link by agent. Manual - the user can configure the redundant mapping for port on the same link or to the other link on any TU Adjacent - similar to auto, but mapping is copied automatically by agent to link on adjacent slot .
INT prtParamPhantom	1.3.6.1.4.1.164.6.2.15.5.1.1.4	INTEGER	read-write	Power feeding to another device.
INT prtParamPSNLayer	1.3.6.1.4.1.164.6.2.15.5.1.1.22	INTEGER	read-write	This object indicates the network layer from which clock is derived.
INT prtParamResetStatsCmd	1.3.6.1.4.1.164.6.2.15.5.1.1.5	INTEGER	read-write	Reset statistics of the selected port.
INT prtParamRxSsm	1.3.6.1.4.1.164.6.2.15.5.1.1.23	INTEGER	read-write	This object indicates if Station Clock SSM messages received will serve as criteria for clock selection.
I32 prtParamSignalLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.17	Integer32	read-only	This object indicates signal level (in thenth of dB units) on selected port.
INT prtParamStatus	1.3.6.1.4.1.164.6.2.15.5.1.1.16	INTEGER	read-only	Station clock source Status.
prtParamTable	1.3.6.1.4.1.164.6.2.15.5.1		not-accessible	This table includes general port parameters. The meaning is different for every product that supports it due to a general parameter - prtControlCnfg. For ACE2002: -This table is used as a mechanism to create the next interface index. The algorithm description: The NMS will send the agent the following get command: get(nextIfIndex.index), where index=interface on which the new index is dependent on. Upon this command the agent will generate and return the new index to the NMS. - This table is partially supported according to the interface type. Upon getNext function the irrelevant parameters will be skipped.
INT prtParamTxClk	1.3.6.1.4.1.164.6.2.15.5.1.1.27	INTEGER	read-write	enable/disable station clock signal output.
INT prtParamUsage	1.3.6.1.4.1.164.6.2.15.5.1.1.11	INTEGER	read-write	Defines whether this port works as User port or as Network port.
I32 prtPerfBBE	1.3.6.1.4.1.164.6.2.15.3.1.1.7	Integer32	read-only	Number of Background Block (or Frame) Errors for the reference period (prtPerfPeriodRef).
I32 prtPerfBlocksPerSec	1.3.6.1.4.1.164.6.2.15.3.1.1.8	Integer32	read-only	Blocks per second (or frames per second) of the port/interface indicated by portIdx. This object is constant for a certain port/interface. It is not affected by the prtPerfPeriodRef index.
I32 prtPerfElapsedTime	1.3.6.1.4.1.164.6.2.15.3.1.1.3	Integer32	read-only	Elapsed Time in seconds. - for prtPerfPeriodRef=currentPeriod: The period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. - for prtPerfPeriodRef=lastPeriod: The value of prtPerfElapsedTime when last prtPerfSaveAndResetCmd was received.
prtPerfEntry	1.3.6.1.4.1.164.6.2.15.3.1.1		not-accessible	An entry in table.
I32 prtPerfES	1.3.6.1.4.1.164.6.2.15.3.1.1.5	Integer32	read-only	Number of Errored Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfIdx	1.3.6.1.4.1.164.6.2.15.3.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
prtPerformance	1.3.6.1.4.1.164.6.2.15.3
INT prtPerfPeriodRef	1.3.6.1.4.1.164.6.2.15.3.1.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. lastPeriod - the period between last two commands of prtPerfSaveAndResetCmd. - If only one command occured since Start-up: the period between Start-up and last command. - If no command occured since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
INT prtPerfSaveAndResetCmd	1.3.6.1.4.1.164.6.2.15.3.1.1.10	INTEGER	read-write	A command per port/interface, to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. This object is applicable only for prtPerfPeriodRef=currentPeriod. Setting this object to on(3) for prtPerfPeriodRef=last, will cause the agent to return: Bad Value response. When setting validly this object to on(3), agent will perform the required command and will reset automatically the value of this object to off(2). Setting this object to off(2), will do nothing.
I32 prtPerfSES	1.3.6.1.4.1.164.6.2.15.3.1.1.6	Integer32	read-only	Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef).
prtPerfTable	1.3.6.1.4.1.164.6.2.15.3.1		not-accessible	This table includes G.826 ports or interfaces.
TIK prtPerfTimeTag	1.3.6.1.4.1.164.6.2.15.3.1.1.9	TimeTicks	read-only	Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was executed. This object is applicable only for prtPerfPeriodRef=lastPeriod. For prtPerfPeriodRef=currentPeriod, the value will always be 0.
I32 prtPerfUAS	1.3.6.1.4.1.164.6.2.15.3.1.1.4	Integer32	read-only	Number of Unavailable Seconds for the reference period (prtPerfPeriodRef).
prtPh1MlCnfg	1.3.6.1.4.1.164.3.2.3.2.2
INT prtPhMlBus	1.3.6.1.4.1.164.3.2.3.2.2.5.1.11	INTEGER	read-write	The TDM BUS this port is linked to.
INT prtPhMlCAS	1.3.6.1.4.1.164.3.2.3.2.2.5.1.6	INTEGER	read-write	This attribute indicates whether Channel Associated Signaling (CAS) is used.
INT prtPhMlClockMode	1.3.6.1.4.1.164.3.2.3.2.2.5.1.7	INTEGER	read-write	Clock mode.
INT prtPhMlClockPolarity	1.3.6.1.4.1.164.3.2.3.2.2.5.1.18	INTEGER	read-write	This object indicates the clock polarity.
INT prtPhMlClockSource	1.3.6.1.4.1.164.3.2.3.2.2.5.1.13	INTEGER	read-write	The Clock Source: TC (Tx Clock) or RC (Rx Clock) signals.
prtPhMlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.5.1		not-accessible	An entry in table.
I32 prtPhMlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
prtPhMlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.5		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
INT prtPhMlConnect	1.3.6.1.4.1.164.3.2.3.2.2.5.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtPhMlControlSignals	1.3.6.1.4.1.164.3.2.3.2.2.5.1.16	INTEGER	read-write	This object shows whether the Port will ignore or implement the control signals like DCD, CTS, DTR.
INT prtPhMlCorrectionMode	1.3.6.1.4.1.164.3.2.3.2.2.5.1.15	INTEGER	read-write	This object is applicable only when prtPhMlErrCorrection=yes. random - enables to correct up to 3 random errors in an 23 bit frame built from 12 data bits and 11 appended parity bits. bursty - interleaving 3 frames, allows correcting bursts of 9 bit length.
INT prtPhMlDialProcess	1.3.6.1.4.1.164.3.2.3.2.2.5.1.9	INTEGER	read-write	Dial Process.
INT prtPhMlErrCorrection	1.3.6.1.4.1.164.3.2.3.2.2.5.1.14	INTEGER	read-write	This object indicates if Error Correction mechanism should be applied or not. It will be applicable only if the interface HW includes the Error Correction chip.
INT prtPhMlInterfaceType	1.3.6.1.4.1.164.3.2.3.2.2.5.1.17	INTEGER	read-write	The SW Configurable Interface Type.
INT prtPhMlMfSyncSlot	1.3.6.1.4.1.164.3.2.3.2.2.5.1.12	INTEGER	read-write	This attribute indicates whether the sync is synchronized according to a certain card and the slot of this card. This operation is required in order to bypass signaling of PCM voice channels. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtPhMlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.3	INTEGER	read-only	This attribute indicates a unique port number. ML-20 cards have just one external interface.
INT prtPhMlRate	1.3.6.1.4.1.164.3.2.3.2.2.5.1.5	INTEGER	read-write	This attribute indicates the configured port speed. auto - rate is adapted automatically to the attached modem rate.
INT prtPhMlSatBuffer	1.3.6.1.4.1.164.3.2.3.2.2.5.1.8	INTEGER	read-write	Satellite Buffer (+/- 256).
INT prtPhMlSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used.
I32 prtPhMlSyncRestore	1.3.6.1.4.1.164.3.2.3.2.2.5.1.10	Integer32	read-write	Sync Restoration time, in seconds. notApplicable=0.
prtPhPlCnfg	1.3.6.1.4.1.164.3.2.3.2.3
prtPhyConfigEntry	1.3.6.1.4.1.164.3.1.6.8.1.2.1		not-accessible	An entry in the Phy Config table.
prtPhyConfigTable	1.3.6.1.4.1.164.3.1.6.8.1.2		not-accessible	The Phy Config table. Used now for Phy25.6 Mbps.
prtPhyCurrentEntry	1.3.6.1.4.1.164.3.1.6.8.2.1.1		not-accessible	An entry in the 25.6 Mbps Line Current table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.
G32 prtPhyCurrentES	1.3.6.1.4.1.164.3.1.6.8.2.1.1.5	Gauge32	read-only	The number of Errored Seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentLOF	1.3.6.1.4.1.164.3.1.6.8.2.1.1.7	Gauge32	read-only	The number of Loss of Frames, encountered by an interface in the current 15 minute interval.
G32 prtPhyCurrentLOS	1.3.6.1.4.1.164.3.1.6.8.2.1.1.1	Gauge32	read-only	The counter associated with the number of Loss Of Sync seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentLSV	1.3.6.1.4.1.164.3.1.6.8.2.1.1.2	Gauge32	read-only	The counter associated with the number of Line symbol violation seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentSES	1.3.6.1.4.1.164.3.1.6.8.2.1.1.4	Gauge32	read-only	The counter associated with the number of SES encountered by a 25.6 Mbps interface in the current 15 minute interval.
OCT prtPhyCurrentStatus	1.3.6.1.4.1.164.3.1.6.8.2.1.1.6	OCTET STRING	read-only	The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
prtPhyCurrentTable	1.3.6.1.4.1.164.3.1.6.8.2.1		not-accessible	The 25.6 Mbps Section/Line Current table.
G32 prtPhyCurrentUAS	1.3.6.1.4.1.164.3.1.6.8.2.1.1.3	Gauge32	read-only	The counter associated with the number of UAS encountered by a 25.6 Mbps interface in the current 15 minute interval.
prtPhyIntervalEntry	1.3.6.1.4.1.164.3.1.6.8.2.2.1		not-accessible	An entry in the 25.6 Mbps Line Interval table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.
G32 prtPhyIntervalES	1.3.6.1.4.1.164.3.1.6.8.2.2.1.6	Gauge32	read-only	The number of Errored Seconds, encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalLOF	1.3.6.1.4.1.164.3.1.6.8.2.2.1.8	Gauge32	read-only	The number of Loss of Frames, encountered by an interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalLOS	1.3.6.1.4.1.164.3.1.6.8.2.2.1.2	Gauge32	read-only	The counter associated with the number of Loss Of Sync seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalLSV	1.3.6.1.4.1.164.3.1.6.8.2.2.1.3	Gauge32	read-only	The counter associated with the number of line symbol violation seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
I32 prtPhyIntervalNumber	1.3.6.1.4.1.164.3.1.6.8.2.2.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 prtPhyIntervalSES	1.3.6.1.4.1.164.3.1.6.8.2.2.1.5	Gauge32	read-only	The counter associated with the number of SES encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
OCT prtPhyIntervalStatus	1.3.6.1.4.1.164.3.1.6.8.2.2.1.7	OCTET STRING	read-only	The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
prtPhyIntervalTable	1.3.6.1.4.1.164.3.1.6.8.2.2		not-accessible	The Line Interval table.
G32 prtPhyIntervalUAS	1.3.6.1.4.1.164.3.1.6.8.2.2.1.4	Gauge32	read-only	The counter associated with the number of UAS encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
prtPhyPerfHistory	1.3.6.1.4.1.164.3.1.6.8.2
I32 prtPhyTimeElapsed	1.3.6.1.4.1.164.3.1.6.8.1.2.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period.
I32 prtPhyValidIntervals	1.3.6.1.4.1.164.3.1.6.8.1.2.1.2	Integer32	read-only	The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute since the interface has been online.
prtPriorityEntry	1.3.6.1.4.1.164.6.3.4.1.1		not-accessible	An entry in table.
I32 prtPriorityIdx	1.3.6.1.4.1.164.6.3.4.1.1.3	Integer32	not-accessible	This object indicates the Traffic Priority Index.
I32 prtPriorityIdx1	1.3.6.1.4.1.164.6.3.4.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. or any other Index.
I32 prtPriorityIngressRateLimit	1.3.6.1.4.1.164.6.3.4.1.1.4	Integer32	read-write	The maximum rate permitted at Ingress of this port with this Traffic Priority, in Kbps.
I32 prtPriorityPrtIdx	1.3.6.1.4.1.164.6.3.4.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
prtPriorityTable	1.3.6.1.4.1.164.6.3.4.1		not-accessible	A table - Parameters per port per Priority .
prtPVc4Cnfg	1.3.6.1.4.1.164.3.2.3.2.9
INT prtQosDirection	1.3.6.1.4.1.164.6.3.4.2.1.3	INTEGER	not-accessible	This object indicates the port's QoS Direction.
prtQosEntry	1.3.6.1.4.1.164.6.3.4.2.1		not-accessible	An entry in table.
U32 prtQosIdx	1.3.6.1.4.1.164.6.3.4.2.1.1	Unsigned32	not-accessible	The first index of the table. This attribute might indicate the Idx of the Cnfg (1..255) being accessed ; Idx of 255 relates to the TmpCnfg or any other Index.
U32 prtQosPrtIdx	1.3.6.1.4.1.164.6.3.4.2.1.2	Unsigned32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
U32 prtQosRateLimitCBS	1.3.6.1.4.1.164.6.3.4.2.1.6	Unsigned32	read-write	This object indicates the port's CBS (Committed Burst Size) in KB. Value=0 represents best effort.
U32 prtQosRateLimitCIR	1.3.6.1.4.1.164.6.3.4.2.1.5	Unsigned32	read-write	This object indicates the port's CIR (Committed Information Rate) in Kbps. Value=0 represents best effort.
U32 prtQosRateLimitEBS	1.3.6.1.4.1.164.6.3.4.2.1.8	Unsigned32	read-write	This object indicates the port's EBS (Excess Burst Size) in KB.
U32 prtQosRateLimitEIR	1.3.6.1.4.1.164.6.3.4.2.1.7	Unsigned32	read-write	This object indicates the port's EIR (Excess Information Rate) in Kbps.
INT prtQosRateLimitPacketType	1.3.6.1.4.1.164.6.3.4.2.1.4	INTEGER	read-write	This object indicates the Type of Packets on which Rate Limitation is applied.
prtQosTable	1.3.6.1.4.1.164.6.3.4.2		not-accessible	Port QoS (Quality of Service) table.
INT prtSActiveStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.5	INTEGER	read-only	This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the ch is not connected according to the active config. offLine(3) indicates that the ch is down (not working) because of any problem. onLine(4) indicates that the ch is up (working) offLineRedundancy(5) indicates that the ch is down, because it is redundant port. onLineRedundancy(6) indicates that the ch is up, and it is the active link
I32 prtSAlarmCode	1.3.6.1.4.1.164.3.3.3.1.4.1.1.3	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
I32 prtSAlarmCounter	1.3.6.1.4.1.164.3.3.3.1.4.1.1.8	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
prtSAlarmEntry	1.3.6.1.4.1.164.3.3.3.1.4.1.1		not-accessible	An entry in table.
I32 prtSAlarmIdx	1.3.6.1.4.1.164.3.3.3.1.4.1.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive.
INT prtSAlarmInvert	1.3.6.1.4.1.164.3.3.3.1.4.1.1.6	INTEGER	read-only	Alarm Invert is : on/off.
INT prtSAlarmMask	1.3.6.1.4.1.164.3.3.3.1.4.1.1.5	INTEGER	read-only	Alarm Mask is : on/off.
INT prtSAlarmOnOff	1.3.6.1.4.1.164.3.3.3.1.4.1.1.7	INTEGER	read-only	Alarm state is : on/off.
I32 prtSAlarmPrtIdx	1.3.6.1.4.1.164.3.3.3.1.4.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT prtSAlarmState	1.3.6.1.4.1.164.3.3.3.1.4.1.1.4	INTEGER	read-only	This object indicates the port alarm severity.
prtSAlarmTable	1.3.6.1.4.1.164.3.3.3.1.4.1		not-accessible	A table.
INT prtSAlrCardType	1.3.6.1.4.1.164.3.1.4.1.2.1.11	INTEGER	read-only	This attribute indicates the type of card installed in the specific slot position. The enumeration is according to mdlSInstCardType.
I32 prtSAlrCode	1.3.6.1.4.1.164.3.1.4.1.2.1.5	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at port level.
STR prtSAlrCodeDescription	1.3.6.1.4.1.164.3.1.4.1.2.1.4	DisplayString	read-only	This attribute is a full text description of the alarm. The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
I32 prtSAlrCounter	1.3.6.1.4.1.164.3.1.4.1.2.1.8	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
prtSAlrEntry	1.3.6.1.4.1.164.3.1.4.1.2.1		not-accessible	An entry in table.
I32 prtSAlrIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive
INT prtSAlrInvert	1.3.6.1.4.1.164.3.1.4.1.2.1.10	INTEGER	read-only	Alarm invert : on/off.
INT prtSAlrMask	1.3.6.1.4.1.164.3.1.4.1.2.1.9	INTEGER	read-only	Alarm mask : on/off.
I32 prtSAlrPrtIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.3	Integer32	read-only	This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a port which does not exist. Valid valuesfor MP-2100/2200: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148), IP Bundles. For other products, see product's spec.
INT prtSAlrSeverity	1.3.6.1.4.1.164.3.1.4.1.2.1.6	INTEGER	read-only	The severity of the alarm.
INT prtSAlrSltIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.2	INTEGER	read-only	This attribute indicates a unique identifier of the slot where the card is inserted. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
INT prtSAlrState	1.3.6.1.4.1.164.3.1.4.1.2.1.7	INTEGER	read-only	State of the alarm.
INT prtSAlrStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.6	INTEGER	read-only	Indicates the alarm state in the port(ch) agent level. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
prtSAlrTable	1.3.6.1.4.1.164.3.1.4.1.2		not-accessible	The list of port agent alarms.
INT prtSBertClrCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.12	INTEGER	read-write	Setting this attribute initiates bert count clear operation. It is valid only when bert test is active on the specific port.
I32 prtSBertTstRslt	1.3.6.1.4.1.164.3.1.4.1.1.1.13	Integer32	read-only	This attribute indicates the number of Bit Error Rate indicated during the BERT operation. It is valid only when bert test is active on the specific port.
INT prtSClearAlrCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.8	INTEGER	read-write	Setting this attribute to on(3) enforces a clear operation of the alarm status events in the given port. The clear operation will not be applied for masked/inverted alarms.
prtSDs3IfTable	1.3.6.1.4.1.164.3.1.6.3.1.1		not-accessible	The DS3 interface table.
INT prtSExHsfInterfaceTyp	1.3.6.1.4.1.164.3.2.3.1.6.1.3	INTEGER	read-only	This attribute indicates a unique interface type of a selected port.
INT prtSExHsfPrtIdx	1.3.6.1.4.1.164.3.2.3.1.6.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtSExHsfRts	1.3.6.1.4.1.164.3.2.3.1.6.1.4	INTEGER	read-only	This attribute indicates a unique RTS control signal state.
INT prtSExHsfSltIdx	1.3.6.1.4.1.164.3.2.3.1.6.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
prtSExHsfStatEntry	1.3.6.1.4.1.164.3.2.3.1.6.1		not-accessible	An entry in table.
prtSExHsfStatTable	1.3.6.1.4.1.164.3.2.3.1.6		not-accessible	A table.
prtSInstEntry	1.3.6.1.4.1.164.3.1.4.1.1.1		not-accessible	An entry in table.
I32 prtSInstIfIndex	1.3.6.1.4.1.164.3.1.4.1.1.1.4	Integer32	read-only	This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx the value will be '7fffffff'h.
I32 prtSInstPrtIdx	1.3.6.1.4.1.164.3.1.4.1.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port in a specific card. The valid ports depend on the installed card: the valid external ports (interfaces) are (1..mdlCNoOfExternPrt) if any, and the valid internal ports are (101..100+mdlCNoOfInternPrt) if any. Generally, for MP-2100/2200: exPrt1 (1) .. exPrt16 (16),inPrt1(101) .. inPrt48 (148) For the Vmux-2100 device: This index will have values of 1...4 for the physical ports & values of ifIndex for the bundles. For other products, see product's spec.
INT prtSInstPrtType	1.3.6.1.4.1.164.3.1.4.1.1.1.3	INTEGER	read-only	This attribute describes the type of the designated port. In MX 3000 only external & internal options are used. All the other options are only for MX 30/300 which need special handling. In order to support interface types in MX 3000, return an ascii string for prtSInterfaceType in this table or support the general RAD value of physicalConnector. External port - is a port with a physical connector. Internal port - might be of two types: a) A composite port which collects a few external ports data into a common bandwidth (usually routed through DS1 link) b) A port which gets only part of the external ports (usually a few DS0's) The following types are used when all ports are external/ internal and the connector/interface type is necessary (for example, stand-alone units): High Speed port types Low Speed port types Voice port types, CL port types. ISDN Voice in MX 30/300 Phase 4: voiceS0 (16), voiceU (17) should be used. ISDN Voice in MX 30/300 Phase 5: voiceQsigS(18), voiceQsigU (19) should be used.
INT prtSInstSltIdx	1.3.6.1.4.1.164.3.1.4.1.1.1.1	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted. In the ?004 Unit the entries io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
prtSInstTable	1.3.6.1.4.1.164.3.1.4.1.1		not-accessible	A table.
STR prtSInterfaceType	1.3.6.1.4.1.164.3.1.4.1.1.1.14	DisplayString	read-only	This attribute indicates a unique HW interface type of the selected port.
INT prtSMaskedAlrStat	1.3.6.1.4.1.164.3.1.4.1.1.1.7	INTEGER	read-only	Indicates the alarm state in the port(ch) agent level, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
prtSP	1.3.6.1.4.1.164.3.3.3.4
INT prtSpActCallOut	1.3.6.1.4.1.164.3.3.3.4.1.1.20	INTEGER	read-write	This object indicates when to Activate Call-Out. It is used by FCD-T1/E1. always - to activate call-out always. linkFail - to activate call-out only when Link of Inband Management fails.
INT prtSpAlrRelayMode	1.3.6.1.4.1.164.3.3.3.4.1.1.21	INTEGER	read-write	This attribute indicates the Alarm Relay Mode. notApplicable - for DP.
STR prtSpAltNum	1.3.6.1.4.1.164.3.3.3.4.1.1.17	DisplayString	read-write	For DXC - this object is applicable only for port (2) = DP. It is the Alternate dialing number. This number is applicable only if prtSpAltNumMode is 'yes'.
INT prtSpAltNumMode	1.3.6.1.4.1.164.3.3.3.4.1.1.15	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. It determines wether to use the alternate number or not. Default = no.
OCT prtSParamStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.15	OCTET STRING	read-only	This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For VC-6, VC-6A, VC-6AG, VC-6A/4LB, VC-12, VC-12/6, external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 \|___\| \|_______\| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|___________\| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For ACM external port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|_________\| spare Alarm State Alarm State: according to bits 1,0: 00=NA ; 01=unused ; 10=Off ; 11=On - For HS-U/1 external port - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For MTML-2/4 external ports, ML-8 externalports, ML-IP (MTML-IP) internal ports and MTML-E2 internal ports - 1 Octet : Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) - For ML-20N external ports - 4 Octets - 1 MS Octet will represent the Actual Link Rate: Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| spare Rate Valid values: 0..34, meaning: 0..32 = (0..32)x64Kbps 33 = Invalid Rate 34 = not applicable (when Rate is not Auto) 35 = 0 Kbps Invalid values: 36..255. - 2 middle Octets will represent the Status of 4 Control Signals: - LS Octet - Bits 3-0: RTS/C (Command, for X.21 interface) Bits 7-4: DCD/I (Indication for X.21 interface) - MS Octet - Bits 3-0: DTR Bits 7-4: DSR Each 4 Bits are divided as follows: - 2 MS bits: DCE - 2 LS bits: DTE For each 2 bits (DCE/DTE): 00=NA ; 01=unused ; 10=Off ; 11=On. - LS Octet: (as for MTML-2): Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) - For MP-2100/2200 MSL-4/E1, MSL-8/E1 External ports - 3 Octets - MS octet: far-end modem channel interface - Middle octet: Material (plastic/metal), far-end modem type, synchronization with far-end modem - LS octet: BERT state (at port/TS/Bit level) - MS octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) 0000 1011 = IR-ETH-QN Rest of the combinations: reserved - Middle octet: Bit 7 6 5 4 3 2 1 0 LSB \| \|___________\| \|__\| Box material modem sync Box material modem: 00000 = other sync: 00 = not sync (for ASMi-52 SA) 00001 = unknown 01 = sync 0=metal 00010 = reserved 10 = reserved 1=plastic 00011 = reserved 11 = reserved 00100 = reserved 00101 = reserved 00110 = ASMi-52 SA/2W/Slave 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD-IP 01101 = FCD-IPM 01110 = D8SL card of DXC-30 01111 = ASMi-52A 10000 = MP card (SHDSL) 10001 = ASMi-52L Rest = reserved - LS Octet: (as for MTML-2): Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs) 1 = ON (BERT is running on this port OR on one of its TSs) - For MP-4100 MSL card Links - 4 Octets - MS octet: far-end modem DTE2 interface (same as for MP-2100 MSL cards) - after MS octet: far-end modem DTE1 interface (same as for MP-2100 MSL cards) - before LS octet: Material (plastic/metal), far-end modem type, synchronization with far-end modem (same as for MP-2100 MSL cards) - LS octet: BERT state (at port/TS/Bit level)- same as for MP-2100 MSL cards - For MP-4100, LRS-102 OP-108/106 Links - 3 Octets - MS octet: far-end PS type and state - Middle octet: synchronization with far-end device - LS octet: BERT state (at port/TS level) - same as for MP-2100 MSL cards - MS octet: Bit 7 6 5 4 3 2 1 0 LSB \|__\| \|__\| \|__\| \|__\| PS-A PS-A PS-B PS-B PS Type PS State PS Type PS State 00=None 00=None 01=AC-DC 01=OK 10=DC 10=Fail - Middle octet: Bit 7 6 5 4 3 2 1 0 LSB \|__\| sync: 00 = not sync 01 = sync 10 = reserved 11 = reserved Rest = reserved
INT prtSpCallOutMode	1.3.6.1.4.1.164.3.3.3.4.1.1.7	INTEGER	read-write	This attribute indicates the call-out mode. For DXC - this object is applicable only for the DP port (2).
OCT prtSpCmd	1.3.6.1.4.1.164.3.3.3.4.1.1.19	OCTET STRING	read-write	SP Command. For LRS this parameter will be used for a Modem Command. Upon NMS's Get operation for devices that this parameter is notApplicable, agent will send NULL string.
prtSpCnfgEntry	1.3.6.1.4.1.164.3.3.3.4.1.1		not-accessible	All the entries at this table are identical(have the same value) at all the configurations(1..255) except at the TmpCnfg. - For products supporting more than one configuration, the write operation into the Table Objects is valid only at the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table Objects will be to prtSpCnfgIdx=1.
I32 prtSpCnfgIdx	1.3.6.1.4.1.164.3.3.3.4.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
prtSpCnfgTable	1.3.6.1.4.1.164.3.3.3.4.1		not-accessible	A table.
INT prtSpCTS	1.3.6.1.4.1.164.3.3.3.4.1.1.9	INTEGER	read-write	CTS line state. This object is applicable only for port (1) = SP
INT prtSpDataBits	1.3.6.1.4.1.164.3.3.3.4.1.1.5	INTEGER	read-write	This attribute indicates the number of data bits in async frame
INT prtSpDcdDelay	1.3.6.1.4.1.164.3.3.3.4.1.1.10	INTEGER	read-write	DCD delay in msec. d10 = delay of 10msec. This object is applicable only for port (1) = SP
INT prtSpDialMode	1.3.6.1.4.1.164.3.3.3.4.1.1.14	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. Dialing mode. Default=tone
INT prtSpDsr	1.3.6.1.4.1.164.3.3.3.4.1.1.11	INTEGER	read-write	DSR line state. This object is applicable only for port (1) = SP
prtSpEntry	1.3.6.1.4.1.164.6.2.15.2.1.1		not-accessible	Supervisory port parameter table.
INT prtSpInterface	1.3.6.1.4.1.164.3.3.3.4.1.1.8	INTEGER	read-write	This attribute indicates the supervisory port interface. dce - the DACS appears as a DCE for the port. dte - the DACS operates as a DTE, for connection via modem, for the port.
I32 prtSpNoOfRetries	1.3.6.1.4.1.164.3.3.3.4.1.1.12	Integer32	read-write	For DXC - this object is applicable only for port (2) = DP. The number of dialing retries requested. Default = 0
INT prtSpParity	1.3.6.1.4.1.164.3.3.3.4.1.1.6	INTEGER	read-write	This attribute indicates the parity mode in async frame
STR prtSpPrimaryNum	1.3.6.1.4.1.164.3.3.3.4.1.1.16	DisplayString	read-write	For DXC - this object is applicable only for port (2) = DP. It is the Primary dialing number.
I32 prtSpPrtIdx	1.3.6.1.4.1.164.3.3.3.4.1.1.2	Integer32	read-only	This attribute indicates a unique port number of the SPor DP port. For DXC, it is the port in the active DCL card: - SP = 1 - NP ; DP = 2 For Kilomux, the port index is calculated as follows: 100*Slot+Ch. For FCD, PRBi, the SP port index=1. For Optimux-T3, the SP port index=71.
INT prtSpRate	1.3.6.1.4.1.164.3.3.3.4.1.1.4	INTEGER	read-write	This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
INT prtSpRoutProtocol	1.3.6.1.4.1.164.3.3.3.4.1.1.18	INTEGER	read-write	This attribute indicates the routing protocol of the port. notApplicable - for DP.
INT prtSpStopBits	1.3.6.1.4.1.164.3.3.3.4.1.1.22	INTEGER	read-write	This attribute indicates number of stop bits in an async frame.
prtSpTable	1.3.6.1.4.1.164.6.2.15.2.1		not-accessible	A table.
INT prtSpUsage	1.3.6.1.4.1.164.3.3.3.4.1.1.3	INTEGER	read-write	This attribute indicates what is the usage of the port.
INT prtSpWaitForConnect	1.3.6.1.4.1.164.3.3.3.4.1.1.13	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. Waiting time for connect, in seconds. Default = 30 sec.
INT prtSRdnStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.17	INTEGER	read-only	Redundancy Status of this port. noRdn - this port is not part of a Redundancy pair/group. offline - this port is offline from Redundancy point of view. online - this port is online from Redundancy point of view.
NTF prtStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.3			This trap is sent whenever the state of a port changed. Attached, will be parameter/s that indicate the new port status. The attached variables will be specified in the specifications of the products supporting this trap.
I32 prtSTestMask	1.3.6.1.4.1.164.3.1.4.1.1.1.9	Integer32	read-only	This is a mask which indicates which tests from the 'prtSTstCmd' list are allowed for the requested port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
OCT prtSTestMaskXp	1.3.6.1.4.1.164.3.1.4.1.1.1.16	OCTET STRING	read-write	This is an Expanded test mask of the prtSTestMask object. The prtSTestMask object reached its maximum, being an Integer with 32 bits. This object indicates which tests from the 'prtSTstCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 csuLoopAndBert 32 dsuLoopAndBert 33 remoteOcuLoopAndBert 34 remoteCsuLoopAndBert 35 remoteDsuLoopAndBert 36 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
INT prtSTstCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.10	INTEGER	read-write	Setting this attribute to any of the above values will initiate a test on the specific port if the operation is legal. If the operation is not legal, the mux will ignore the operation. testPerTS(31) - when this test is selected, the selection of tests for each TS is done via the prtExPh1MlTsTest object. If a test time out is needed, the test will be set with a default timeout of 2 minutes until the user will set the parameter 'prtSTstDuration' to the required time out. If no time out is needed , the test will be set with infinite timeout until the user will set the parameter 'prtSTstDuration' to the required time out.
I32 prtSTstDuration	1.3.6.1.4.1.164.3.1.4.1.1.1.11	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to all the test operations. The resolution will be a minute, and the maximum duration is limited to 30 minutes. For Vmux devices, the values are in seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtSTstCmd' parameter.
prtSupervisory	1.3.6.1.4.1.164.6.2.15.2
INT prtSupervisoryCTS	1.3.6.1.4.1.164.6.2.15.2.1.1.8	INTEGER	read-write	CTS line state.
INT prtSupervisoryDataBits	1.3.6.1.4.1.164.6.2.15.2.1.1.3	INTEGER	read-write	This attribute indicates the number of data bits in an async frame
INT prtSupervisoryDcdDelay	1.3.6.1.4.1.164.6.2.15.2.1.1.9	INTEGER	read-write	DCD delay in msec.
INT prtSupervisoryDSR	1.3.6.1.4.1.164.6.2.15.2.1.1.10	INTEGER	read-write	DSR line state.
I32 prtSupervisoryIndex	1.3.6.1.4.1.164.6.2.15.2.1.1.1	Integer32	read-only	The SP port index. For some products, having modules (cards): The LS byte of the integer is the port index 1..255. The MS byte is different than 0 only if the port belongs to a module. In that case it is the module number. For other products' index see their specification.
INT prtSupervisoryInterface	1.3.6.1.4.1.164.6.2.15.2.1.1.7	INTEGER	read-write	This attribute indicates the supervisory port interface.
INT prtSupervisoryParity	1.3.6.1.4.1.164.6.2.15.2.1.1.4	INTEGER	read-write	This attribute indicates the parity mode in an async frame
INT prtSupervisoryRate	1.3.6.1.4.1.164.6.2.15.2.1.1.2	INTEGER	read-write	This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
INT prtSupervisoryRoutProtocol	1.3.6.1.4.1.164.6.2.15.2.1.1.11	INTEGER	read-write	This attribute indicates the routing protocol of the port. notApplicable - for DP.
INT prtSupervisoryStopBits	1.3.6.1.4.1.164.6.2.15.2.1.1.5	INTEGER	read-write	This attribute indicates the parity mode in an async frame.
INT prtSupervisoryUsage	1.3.6.1.4.1.164.6.2.15.2.1.1.6	INTEGER	read-write	This attribute indicates the usage of the SP port.
prtT1E1	1.3.6.1.4.1.164.3.3.3.2
G32 prtT1E1BpvLastMin	1.3.6.1.4.1.164.3.3.3.2.1.1.4	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the number of BPV (BiPolar Violation) events detected during the last minute.
G32 prtT1E1BpvMax	1.3.6.1.4.1.164.3.3.3.2.1.1.5	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the maximal number of BPV (BiPolar Violation) events (per minute), detected during the worst minute.
INT prtT1E1CGA	1.3.6.1.4.1.164.3.3.3.2.2.1.10	INTEGER	read-write	This object selects the method used to signal the CGA state to the other end, through the main/sub link. 'none' - non-transparent mode. When one of the links (main/sub) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos Signal' will be transmitted to the other end. 'trans' - when one of the links (main/sub) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main/sub) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos Signal' will be transmitted to the other end.
prtT1E1CnfgEntry	1.3.6.1.4.1.164.3.3.3.2.2.1		not-accessible	An entry in the T1/E1 port configuration table.
I32 prtT1E1CnfgIdx	1.3.6.1.4.1.164.3.3.3.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
prtT1E1CnfgTable	1.3.6.1.4.1.164.3.3.3.2.2		not-accessible	T1/E1 port configuration table.
INT prtT1E1ConnectedTS	1.3.6.1.4.1.164.3.3.3.2.2.1.27	INTEGER	read-only	This parameter indicates if there is any connected TS for this interface.
OCT prtT1E1DataOos	1.3.6.1.4.1.164.3.3.3.2.2.1.14	OCTET STRING	read-write	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
I32 prtT1E1DedicatedTs	1.3.6.1.4.1.164.3.3.3.2.2.1.19	Integer32	read-write	The value is differently determined for different products. There are two methods: 1) A unique number to identify Dedicated TS of the T1/E1 port. It is applicable only when prtExT1E1InbandMng selected is dedicatedTs. 1..24 - Dedicated TS of T1 1..31 - Dedicated TS of E1 255 - notApplicable (for agents that do not support this feature) Other values are invalid. 2) For FCD-STM, up to five TSs may be dedicated to management. This object value is the Sum (sigma) of 2n, where n =TS-1 e.g. Time slots 3,5,7,9,11 are dedicated to management: 2 2 +2 4 +2 6 +2 8 +210 = 4+16+64+256+1024=1364 User should consult the product specification, to find out the method employed.
INT prtT1E1EocTsConfig	1.3.6.1.4.1.164.3.3.3.2.2.1.32	INTEGER	read-write	This object indicates whether the use of EOC for TS Configuration is enabled or not.
INT prtT1E1Fdl	1.3.6.1.4.1.164.3.3.3.2.2.1.7	INTEGER	read-write	This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following is used. 'ansi-T1-403' refers to the FDL exchange recommended by ANSI. 'att-54016' refers to ESF FDL exchanges. 'fdl-none' indicates that the device does not use the FDL. 'transFdl' indicates transition between two ports of the same card.
INT prtT1E1FdlMode	1.3.6.1.4.1.164.3.3.3.2.2.1.8	INTEGER	read-write	Fdl Mode of the T1 selected port. notApplicable - will be used for an E1 port.
OCT prtT1E1FdlMsg	1.3.6.1.4.1.164.3.3.3.2.3.1.4	OCTET STRING	read-only	FDL message.
prtT1E1FdlMsgEntry	1.3.6.1.4.1.164.3.3.3.2.3.1		not-accessible	An entry in table.
INT prtT1E1FdlMsgFdlType	1.3.6.1.4.1.164.3.3.3.2.3.1.2	INTEGER	read-only	The Fdl type reference of the Fdl message.
I32 prtT1E1FdlMsgPrtIdx	1.3.6.1.4.1.164.3.3.3.2.3.1.1	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 .
INT prtT1E1FdlMsgSlt	1.3.6.1.4.1.164.3.3.3.2.3.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
prtT1E1FdlMsgTable	1.3.6.1.4.1.164.3.3.3.2.3		not-accessible	This table is applicable for a T1 interface with 'esf' LineType or E1 interface, when CRC is enabled (LineType).
OCT prtT1E1IdleCode	1.3.6.1.4.1.164.3.3.3.2.2.1.11	OCTET STRING	read-write	This object selects the code transmitted to fill idle (unused) time slots in the main link frame. Valid range: (0 - FF HEX) .
INT prtT1E1InbandMng	1.3.6.1.4.1.164.3.3.3.2.2.1.17	INTEGER	read-write	A unique number to identify an Inband management over the link. internal - supported by KM-2100 only. It means that the management is internal to the frame. It takes part of the ML Frame bits (instead of data).
INT prtT1E1InbandMngRate	1.3.6.1.4.1.164.3.3.3.2.2.1.18	INTEGER	read-write	A unique number to identify the rate of the Inband management. It is required only for E1 links and is applicable only when prtExT1E1InbandMng selected is FdlOrTs0 or dedicatedTs.
INT prtT1E1InbandMngRoutProt	1.3.6.1.4.1.164.3.3.3.2.2.1.20	INTEGER	read-write	Inband Mng Routing Protocol of the port. When prtT1E1InbandMng is 'dedicatedPpp'-'proprietary' and 'rip2' are applicable. For other values - only 'proprietary' is applicable. For FCD-M and FCD-A: When prtT1E1InbandMng is 'dedicatedPpp' or 'dedicatedFr': 'None', 'proprietary' and 'rip2' are applicable. When prtT1E1InbandMng is 'fdlOrTS0' or 'dedicatedTs': 'None' and 'proprietary' are applicable. When prtT1E1InbandMng is 'off': 'None' is applicable.
INT prtT1E1LineCode	1.3.6.1.4.1.164.3.3.3.2.2.1.5	INTEGER	read-write	This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. jbzs=b7zs refers the Jammed Bit Zero Suppres- sion, in which the AT&T specification of at least one pulse every 8 bit periods is literal- ly implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data (used for T1). b8zs refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits (used for T1). ANSI Clear Channels may use zbtsi, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use hdb3 or ami (= TRAN). amI (=TRAN) refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
INT prtT1E1LineLengthMask	1.3.6.1.4.1.164.3.3.3.2.2.1.15	INTEGER	read-write	This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft 'fcc68' - provides compliance with the FCC 68.308 Option A output pulse mask.
INT prtT1E1LineMode	1.3.6.1.4.1.164.3.3.3.2.2.1.25	INTEGER	read-write	Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values
INT prtT1E1LineType	1.3.6.1.4.1.164.3.3.3.2.2.1.4	INTEGER	read-write	This variable indicates the variety of T1/E1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: esf Extended SuperFrame DS1 d4 AT&T D4 format DS1 - SF e1 CCITT Recommendation G.704 (Table 4a) - G732N e1Crc CCITT Recommendation G.704 (Table 4b) - G732N with CRC e1MF G.704 (Table 4a) with TS16 multiframing enabled - G732S e1CrcMF G.704 (Table 4b) with TS16 multiframing enabled - G732S with CRC unframed T1 - applicable values: (1),(2),(3),(8) E1 - applicable values: (1),(4),(5),(6),(7),(8)
INT prtT1E1LinkMode	1.3.6.1.4.1.164.3.3.3.2.2.1.21	INTEGER	read-write	regular - TSs are connected by user via TS Assignment only transparent - when a port with this Link Mode is connected to an internal T1/E1 port of a T3/E3 card, TS0, TS16 and Fbit are transparently transferred to the E3/T3 stream.
I32 prtT1E1MaxTSs	1.3.6.1.4.1.164.3.3.3.2.2.1.31	Integer32	read-write	This object is applicable only for DXC D4T1, D4E1, D8T1, D8E1 external ports and D8GSL internal E1 ports. It is relevant only when sysCIntTsAllocMode=static(2). 255=not applicable If prtT1E1LineType=unframed(8), the value of this object must be 32. Else, the valid values are 0..31.
INT prtT1E1Multiplier	1.3.6.1.4.1.164.3.3.3.2.2.1.22	INTEGER	read-write	The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps. For T1 only.
G32 prtT1E1OosCount	1.3.6.1.4.1.164.3.3.3.2.1.1.3	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the number of red alarm events since the last count clearing.
INT prtT1E1OosSignal	1.3.6.1.4.1.164.3.3.3.2.2.1.12	INTEGER	read-write	'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0
INT prtT1E1PppEchoFailDetection	1.3.6.1.4.1.164.3.3.3.2.2.1.34	INTEGER	read-write	This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Disable. Enable - will be selected mainly when a T1/E1 Ring exists and between 2 adjacent Ring devices there is another device or Net, that causes these Ring devices not to sense that the PPP connection between them is lost. In this case, Echo Request should be initiated by the port.
I32 prtT1E1PrtIdx	1.3.6.1.4.1.164.3.3.3.2.2.1.2	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20.
INT prtT1E1RAI	1.3.6.1.4.1.164.3.3.3.2.2.1.24	INTEGER	read-write	Remote Alarm Signal
INT prtT1E1RemCrc4	1.3.6.1.4.1.164.3.3.3.2.2.1.30	INTEGER	read-write	This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.
INT prtT1E1Role	1.3.6.1.4.1.164.3.3.3.2.2.1.33	INTEGER	read-write	This object indicates whether this port behaves as SUB or Main link.
INT prtT1E1RxGain	1.3.6.1.4.1.164.3.3.3.2.2.1.23	INTEGER	read-write	This attribute is the rx volume (dB).
INT prtT1E1SameFeCnfg	1.3.6.1.4.1.164.3.3.3.2.2.1.29	INTEGER	read-write	This parameter indicates whether the same E1 configuration parameters and TS assignment are set both to the local and remote device. Read-Write access is applicable only in G732N framed mode. For G732S and UNFRAMED this parameter is set by agent to YES and is Read Only. In Case of conflict during power-up between the central and remote, the value set by the central unit is the valid one.
INT prtT1E1SignalMode	1.3.6.1.4.1.164.3.3.3.2.2.1.6	INTEGER	read-write	'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Signaling is in use. 'bitOriented' indicates that E1 Channel Associated Signaling (CAS) is in use. 'messageOriented' indicates that Common Channel Signaling (CCS) is in use either on channel 16 of an E1 link or channel 24 of a T1.
INT prtT1E1Slt	1.3.6.1.4.1.164.3.3.3.2.2.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
I32 prtT1E1SPrtIdx	1.3.6.1.4.1.164.3.3.3.2.1.1.1	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 .
INT prtT1E1SSlt	1.3.6.1.4.1.164.3.3.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
prtT1E1StatEntry	1.3.6.1.4.1.164.3.3.3.2.1.1		not-accessible	An entry in the T1/E1 port statistics table.
prtT1E1StatTable	1.3.6.1.4.1.164.3.3.3.2.1		not-accessible	T1/E1 port statistics table.
INT prtT1E1Sync	1.3.6.1.4.1.164.3.3.3.2.2.1.9	INTEGER	read-write	This object enables returning to normal operation, after the end of a main/sub link red alarm event, in reduced time. 'tr62411' - complies with AT&T TR-62411 (after 10 seconds). Applicable for both T1 and E1 interfaces. 'ccitt' - complies with CCITT standard. Applicable only for E1 interfaces. 'fast' - after 1 second.
INT prtT1E1Ts0SaBit	1.3.6.1.4.1.164.3.3.3.2.2.1.28	INTEGER	read-write	This parameter indicates whether to send TS 0, or not. noMng= TS 0 is looped, therefore not sent. mng= TS 0 isn't looped, therefore it is sent.
OCT prtT1E1TS0SaBits	1.3.6.1.4.1.164.3.3.3.2.2.1.26	OCTET STRING	read-write	This object is applicable only for E1 ports. For T1, string size will be 0. For E1, it enables user to select the use of TS0 Sa Bits 4..8, by 3 octets: The order (in hexa display): free Sa-Bit-4 Sa-Bit-5 Sa-Bit-6 Sa-Bit-7 Sa-Bit-8 \|___________\| \|________________\| \|________________\| MSByte LSByte Each Sa Bit will be represented by a nibble, having the following meaning: 0000 = zero 0001 = one 0010 = management 0011 = transparent the rest are reserved for future use.
INT prtT1E1TxGainMask	1.3.6.1.4.1.164.3.3.3.2.2.1.16	INTEGER	read-write	This attribute is the tx gain mask parameter (dB), used only for T1/CSU interfaces.
OCT prtT1E1VoiceOos	1.3.6.1.4.1.164.3.3.3.2.2.1.13	OCTET STRING	read-write	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT prtT1FdlMsg	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.4	OCTET STRING	read-only	FDL message.
prtT1FdlMsgEntry	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1		not-accessible	An entry in table.
INT prtT1FdlMsgFdlTxRx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.3	INTEGER	read-only	The Fdl tx/rx reference of the Fdl message.
INT prtT1FdlMsgPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.2	INTEGER	read-only	This attribute indicates a unique port number. MTML-1/T1 modules have just one external interface.
INT prtT1FdlMsgSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
prtT1FdlMsgTable	1.3.6.1.4.1.164.3.1.4.1.3.4.1		not-accessible	This table is applicable for a T1 interface with 'esf' LineType .
prtT1Statis	1.3.6.1.4.1.164.3.1.4.1.3.4
prtT3E3	1.3.6.1.4.1.164.3.3.3.8
INT prtT3E3AisFrame	1.3.6.1.4.1.164.3.3.3.8.1.1.6	INTEGER	read-write	This object is applicable only for Optimux-T3. It allows user to select whether the AIS sent will be framed or unframed.
INT prtT3E3AisTransmit	1.3.6.1.4.1.164.3.3.3.8.1.1.9	INTEGER	read-write	Indicates if AIS signal will be transmitted over the tributary E3/DS3 upon failure.
prtT3E3CnfgEntry	1.3.6.1.4.1.164.3.3.3.8.1.1		not-accessible	An entry in the T3/E3 port configuration table.
I32 prtT3E3CnfgIdx	1.3.6.1.4.1.164.3.3.3.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For DXC, write operations can be performed only on the Temp Config. For products that do not support configurations, always 1 will be used.
prtT3E3CnfgTable	1.3.6.1.4.1.164.3.3.3.8.1		not-accessible	T3/E3 port configuration table.
INT prtT3E3InbandMng	1.3.6.1.4.1.164.3.3.3.8.1.1.5	INTEGER	read-write	A unique number to identify the Frame Type over the link. For Optimux-T3: only values (4), (7) are supported.
INT prtT3E3LineLength	1.3.6.1.4.1.164.3.3.3.8.1.1.4	INTEGER	read-write	This object is the length of the ds3 line in feet. It provides information for line build out circuitry if it exists and can use this object to adjust the line build out. len0p450ft = 0 - 450 feet len451p900ft = 451 - 900 feet.
I32 prtT3E3PrtIdx	1.3.6.1.4.1.164.3.3.3.8.1.1.2	Integer32	read-only	This attribute indicates a unique port number. For DXC: The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The external ports convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For Optimux-T3: Link-A: 51 Link-B: 61 .
INT prtT3E3RoutProt	1.3.6.1.4.1.164.3.3.3.8.1.1.8	INTEGER	read-write	Routing Protocol of the port. This object is applicable only for T3 ports.
INT prtT3E3Slt	1.3.6.1.4.1.164.3.3.3.8.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtT3E3TxClockSource	1.3.6.1.4.1.164.3.3.3.8.1.1.7	INTEGER	read-write	Tx Clock Source.
prtTest	1.3.6.1.4.1.164.6.2.15.4
U32 prtTestActivationDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.13	Unsigned32	read-write	This object is applicable only when a single test is running. It indicates test activation delay in seconds. A Value of 0 indicates that the test starts immediately.
U32 prtTestBwProfile	1.3.6.1.4.1.164.6.2.15.4.1.1.25	Unsigned32	read-write	Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test in order to limit the traffic that is looped back.
I32 prtTestCmdAndStatus	1.3.6.1.4.1.164.6.2.15.4.1.1.2	Integer32	read-write	Setting this object to a value as detailed further on (except 0) will initiate a test on the specific port. The test/s requested will be set according to the respective bit. The value of this object will be a sum of (2**n), where n is the Bit: TEST BIT VALUE ----------- --- ------ reserved 0 1 PayloadLoop=RLB 1 (=Remote Loopback) 2 LineLoop=DIG 2 (=Digital) 4 OtherLoop 3 8 InwardLoop=LLB 4 (=Local Loopback) 16 BERT 5 32 LC 6 64 ToneInjection 7 128 Inband 8 256 BERT Remote (or E1/T1 RLB) 9 512 Downstream-AIS (or E1/T1 LLB) 10 1024 Upstream-AIS 11 2048 Rem-Loop-on-Rem-Unit 12 4096 MacSwapLoop 13 8192 OamETHLoopback 14 16384 OamETHLinkTrace 15 32768 e.g : If the requested value is 20 -> 010100 -> Bits 2 & 4 are set -> the requested tests are : LineLoopback=DIG InwardLoopback=LLB Not all tests combinations are valid. For valid test combination, see each product's specification. For LRS52, only single test is allowed simultaneously The terminology and order of the first tests (except BERT) is according to the one used for Test Status of DS1 and DS3 standards. The notations : RLB, LLB, DIG are the most used in RAD's products, but they can be different. For exact definition see product's spec. Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port. When no test is running on the port, the Get value (test status) will be 0. PayloadLoop=RLB The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. LineLoop=DIG The received signal at this interface does not go through the device (minimum penetration) but is looped back out. OtherLoop Loopbacks that are not defined here. InwardLoop=LLB The sent signal at this interface is looped back through the device. LC This loop is applicable only for HSSI interface, towards the router . ToneInjection This loop is applicable for analog voice (like FXS). Downstream-AIS E1 AIS signal (all ones) is transmitted in the relevant channel toward the STM-1 line. Upstream-AIS E1 AIS signal (all ones) is generated in the relevant channel toward the local received tributary channel output Rem-Loop-on-Rem-Unit Request from far end device to activate remote loopback towards near-end device MacSwapLoop This loop is applicable for ethernet port. Loop is implemented by swapping the MAC addresses of the incoming message. OamETHLoopback Ethernet Loopback is used to verify connectivity of a MEP with a MIP or peer MEP(s) (ITU-T Y.1731, Clause 7.2). OamETHLinkTrace Ethernet Link Trace is an on-demand OAM function which can be used for the two following purposes: - Adjacent Relation Retrieval - Fault Localization (ITU-T Y.1731, Clause 7.3).
IP prtTestDestinationIpAddress	1.3.6.1.4.1.164.6.2.15.4.1.1.23	IpAddress	read-write	Indicates the destination IP Address in the transmitted messages that are looped back.
prtTestEntry	1.3.6.1.4.1.164.6.2.15.4.1.1		not-accessible	An entry in table.
I32 prtTestIdx	1.3.6.1.4.1.164.6.2.15.4.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
INT prtTestInitiator	1.3.6.1.4.1.164.6.2.15.4.1.1.4	INTEGER	read-only	This object indicates who initiated this port's test/s.
INT prtTestMacSwapLoopDataMode	1.3.6.1.4.1.164.6.2.15.4.1.1.14	INTEGER	read-write	This object defines which part of the data will be looped back.
MAC prtTestMacSwapLoopDestAddr	1.3.6.1.4.1.164.6.2.15.4.1.1.17	MacAddress	read-write	Configures the MAC address that will be sent in the Destination field of the packet in the outgoing direction.
INT prtTestMacSwapLoopDirection	1.3.6.1.4.1.164.6.2.15.4.1.1.16	INTEGER	read-write	This object defines the direction of the performed loopback. In ETX102 'local' corresponds to Ingress loop (either on User port or on Network port), and 'remote' corresponds to Egress loop (either on User port or on Network port).
MAC prtTestMacSwapLoopSrcAddr	1.3.6.1.4.1.164.6.2.15.4.1.1.18	MacAddress	read-write	Configures the MAC address that will be sent in the Source field of the packet in the outgoing direction.
I32 prtTestMacSwapLoopVlanId	1.3.6.1.4.1.164.6.2.15.4.1.1.15	Integer32	read-write	This object specifies the VLAN ID for prtTestMacSwapLoopDataMode=specificVlan.
U32 prtTestOamAvgRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.21	Unsigned32	read-only	The average round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamMaxRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.20	Unsigned32	read-only	The maximum value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamMinRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.19	Unsigned32	read-only	The mininal value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamTxInterval	1.3.6.1.4.1.164.6.2.15.4.1.1.22	Unsigned32	read-write	Indicates the interval between loopback sent messages.Units are msec.
prtTestTable	1.3.6.1.4.1.164.6.2.15.4.1		not-accessible	This table includes test data for ports or interfaces.
I32 prtTestTimeout	1.3.6.1.4.1.164.6.2.15.4.1.1.5	Integer32	read-write	This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. For RICi-E1T1, RICi-E3T3 the measurement unit is in seconds. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever
U32 prtTestTTL	1.3.6.1.4.1.164.6.2.15.4.1.1.24	Unsigned32	read-write	Time-to-live.Number of hops the loopback message will go through the net before deciding to discard it.
INT prtTestVctCmd	1.3.6.1.4.1.164.6.2.15.4.1.1.10	INTEGER	read-write	Vct command. on (3) = Start Vct on both cables connected to RX and TX connectors of this port. Agent will perform the required command and change automatically the value of this object to off(2).
I32 prtTestVctRxCrossPair	1.3.6.1.4.1.164.6.2.15.4.1.1.11	Integer32	read-only	This object should be equal to the Index (prtTestIdx) of the Rx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair. This object was especially created for ETX-202. Currently not in use.
I32 prtTestVctRxDistance	1.3.6.1.4.1.164.6.2.15.4.1.1.8	Integer32	read-only	This object indicates the distance in Meters to the RX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
INT prtTestVctRxResult	1.3.6.1.4.1.164.6.2.15.4.1.1.6	INTEGER	read-only	This object indicates the result of the Vct on the cable connected to the RX connector.
I32 prtTestVctTxCrossPair	1.3.6.1.4.1.164.6.2.15.4.1.1.12	Integer32	read-only	This object should be equal to the Index (prtTestIdx) of the Tx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.
I32 prtTestVctTxDistance	1.3.6.1.4.1.164.6.2.15.4.1.1.9	Integer32	read-only	This object indicates the distance in Meters to the TX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
INT prtTestVctTxResult	1.3.6.1.4.1.164.6.2.15.4.1.1.7	INTEGER	read-only	This object indicates the result of the Vct on the cable connected to the TX connector.
prtTrafficClass	1.3.6.1.4.1.164.6.3.5
prtTreCnfg	1.3.6.1.4.1.164.3.2.3.2.12
prtVc2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.5.1		not-accessible	An entry in table.
I32 prtVc2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
prtVc2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.5		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to prtVc2CnfgIdx=1.
I32 prtVc2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.3	Integer32	read-only	A unique identifier of the port, within the card. For MP-2100/2200 card ports, Web Ranger and FCD-IP Voice ports the values will be: exPrt1 (1) exPrt2 (2) exPrt3 (3) exPrt4 (4) exPrt5 (5) exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) exPrt10 (10) exPrt11 (11) exPrt12 (12) exPrt13 (13) exPrt14 (14) exPrt15 (15) exPrt16 (16) For LA-240: The index for fixed voice ports will be - exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) The index for voice card ports will be - Slot number * 100 + ch (for IO-1: 101..104, for IO-2: 201..204). For other products' index see their specification.
INT prtVc2SltIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For Stand Alone products like WR: notApplicable (255)
prtVc3Cnfg	1.3.6.1.4.1.164.3.2.3.2.14
prtVcPbxCnfg	1.3.6.1.4.1.164.3.2.3.2.15
prtWanGen	1.3.6.1.4.1.164.3.1.4
qInternalProfileEntry	1.3.6.1.4.1.164.6.3.11.2.1		not-accessible	A conceptual row where each row contains one Queue attribute.
U32 qInternalProfileIndex	1.3.6.1.4.1.164.6.3.11.2.1.1	Unsigned32	not-accessible	Defines the Queue Profile ID.
U32 qInternalProfileQueueLength	1.3.6.1.4.1.164.6.3.11.2.1.5	Unsigned32	read-create	This attribute determines the length of the queue.
U32 qInternalProfileRateLimit	1.3.6.1.4.1.164.6.3.11.2.1.9	Unsigned32	read-create	This attribute determines the Rate Limit of the queue in Kbps. Value=0 represents best effort.
ROW qInternalProfileRowStatus	1.3.6.1.4.1.164.6.3.11.2.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
INT qInternalProfileScheduling	1.3.6.1.4.1.164.6.3.11.2.1.3	INTEGER	read-create	This attribute determines the queue scheduling method.
U32 qInternalProfileShaperProfile	1.3.6.1.4.1.164.6.3.11.2.1.10	Unsigned32	read-create	This attribute defines the Shaper Profile (bwProfileIndex from bwProfileTable) assigned to this qInternalProfile. Valid range of bwProfileIndex for Shaper Profiles is 0x8000001-0x8000041. If set to '0', no profile is assigned to this qInternalProfile.
qInternalProfileTable	1.3.6.1.4.1.164.6.3.11.2		not-accessible	This table holds queue profiles.
U32 qInternalProfileWFQWeight	1.3.6.1.4.1.164.6.3.11.2.1.4	Unsigned32	read-create	This attribute determines the weight that each WFQ (Weighted Fair Queue) participant gets. It is applicable only when scheduling is configured to WFQ.
U32 qInternalProfileWredDropAllThresh	1.3.6.1.4.1.164.6.3.11.2.1.7	Unsigned32	read-create	This attribute determines the length that the queue (Stop Value) must reach before the WRED (Weighted Random Early Detection) shaper mechanism stops dropping randomly, and just drops all further packets marked as yellow.
U32 qInternalProfileWredDropProbability	1.3.6.1.4.1.164.6.3.11.2.1.8	Unsigned32	read-create	This attribute determines the percentage of packets that are being dropped at the point when the length of the queue reaches the Stop value. So, effectively, this defines how quickly the rate of dropping packet must increase as the queue length grows from the Start Value to the Stop Value.
U32 qInternalProfileWredStartDropThresh	1.3.6.1.4.1.164.6.3.11.2.1.6	Unsigned32	read-create	This attribute determines the length that the queue (Start Value) must reach before the packets colored yellow will start being dropped by the WRED (Weighted Random Early Detection/Discard) mechanism. WRED is one the most commonly used method for congestion avoidance.
BIT qosFlowMappingCriteria	1.3.6.1.4.1.164.6.3.9.2.1.5	Bits	read-create	This attribute determines upon which criterion the flow will be mapped.
qosFlowMappingEntry	1.3.6.1.4.1.164.6.3.9.2.1		not-accessible	Each entry in this table describes one Flow Mapping. The information includes combination (AND function) of all the classifications, as defined in the qosFlowMappingCriteria field. Classifiers are: TOS, DSCP, VLAN ID, MAC and IP source and destination addresses, IP protocol, IP Precedence, TCP and UDP source and destination ports.
IP qosFlowMappingFromDestIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.18	IpAddress	read-create	This attribute determines the first destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingFromDestMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.14	MacAddress	read-create	This attribute determines the first destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromDscp	1.3.6.1.4.1.164.6.3.9.2.1.8	Unsigned32	read-create	This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromInnerVlanId	1.3.6.1.4.1.164.6.3.9.2.1.31	Unsigned32	read-create	This attribute determines the first inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromIpPrecedence	1.3.6.1.4.1.164.6.3.9.2.1.28	Unsigned32	read-create	This attribute determines the first IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.
IP qosFlowMappingFromSrcIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.16	IpAddress	read-create	This attribute determines the first source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingFromSrcMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.12	MacAddress	read-create	This attribute determines the first source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromTcpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.22	Unsigned32	read-create	This attribute determines the first TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromTcpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.20	Unsigned32	read-create	This attribute determines the first TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromUdpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.26	Unsigned32	read-create	This attribute determines the first UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromUdpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.24	Unsigned32	read-create	This attribute determines the first UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromVlanId	1.3.6.1.4.1.164.6.3.9.2.1.10	Unsigned32	read-create	This attribute determines the first VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingIdx1	1.3.6.1.4.1.164.6.3.9.2.1.1	Unsigned32	not-accessible	- In case the table is accessed via flowMappingProfileTable this is a running index for the QoS Flow Mapping table. - In case the table is not accessed via flowMappingProfileTable, this will be the ifIndex of the XNI (bridge port) to which the QoS mapping applies.
U32 qosFlowMappingIdx2	1.3.6.1.4.1.164.6.3.9.2.1.2	Unsigned32	not-accessible	An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the index of the Flow (EVC) to which the QoS mapping applies.
U32 qosFlowMappingIdx3	1.3.6.1.4.1.164.6.3.9.2.1.3	Unsigned32	not-accessible	An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the Priority to which the QoS mapping applies.
U32 qosFlowMappingIeee802dot1p	1.3.6.1.4.1.164.6.3.9.2.1.6	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different 802.1 P-bit value. Setting '1' to the bit means that the corresponding 802.1 P-bit value is applicable. It is relevant only in case the ieee802dot1p bit(0) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingInnerIeee802dot1p	1.3.6.1.4.1.164.6.3.9.2.1.30	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different inner 802.1 P-bit value. Setting '1' to the bit means that the corresponding inner 802.1 P-bit value is applicable. It is relevant only in case the innerIeee802dot1p bit (13) in qosFlowMappingCriteria equals 1.
ROW qosFlowMappingRowStatus	1.3.6.1.4.1.164.6.3.9.2.1.4	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
qosFlowMappingTable	1.3.6.1.4.1.164.6.3.9.2		not-accessible	A table of Flow Mapping.
IP qosFlowMappingToDestIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.19	IpAddress	read-create	This attribute determines the last destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingToDestMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.15	MacAddress	read-create	This attribute determines the last destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToDscp	1.3.6.1.4.1.164.6.3.9.2.1.9	Unsigned32	read-create	This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToInnerVlanId	1.3.6.1.4.1.164.6.3.9.2.1.32	Unsigned32	read-create	This attribute determines the last inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToIpPrecedence	1.3.6.1.4.1.164.6.3.9.2.1.29	Unsigned32	read-create	This attribute determines the last IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingTos	1.3.6.1.4.1.164.6.3.9.2.1.7	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different TOS value. Setting '1' to the bit means that the corresponding TOS value is applicable. It is relevant only in case the tos bit (1) in qosFlowMappingCriteria equals 1.
IP qosFlowMappingToSrcIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.17	IpAddress	read-create	This attribute determines the last source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingToSrcMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.13	MacAddress	read-create	This attribute determines the last source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToTcpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.23	Unsigned32	read-create	This attribute determines the last TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToTcpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.21	Unsigned32	read-create	This attribute determines the last TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToUdpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.27	Unsigned32	read-create	This attribute determines the last UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToUdpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.25	Unsigned32	read-create	This attribute determines the last UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToVlanId	1.3.6.1.4.1.164.6.3.9.2.1.11	Unsigned32	read-create	This attribute determines the last VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.
qProfileEntry	1.3.6.1.4.1.164.6.3.11.1.1		not-accessible	A conceptual row where each row contains one Queue Cluster attribute.
U32 qProfileIndex	1.3.6.1.4.1.164.6.3.11.1.1.1	Unsigned32	not-accessible	Defines the Queue Cluster Profile ID.
OCT qProfileInternalQProfile	1.3.6.1.4.1.164.6.3.11.1.1.5	OCTET STRING	read-create	This attribute holds the indexes to the queue profiles in the qInternalProfileTable. Each couple of octets holds an index to the qInternalProfileTable.
STR qProfileName	1.3.6.1.4.1.164.6.3.11.1.1.3	SnmpAdminString	read-create	This attribute holds the name of the Queue cluster profile.
U32 qProfileNumberOfInternalQ	1.3.6.1.4.1.164.6.3.11.1.1.4	Unsigned32	read-create	This attribute holds the number of the internal queue profiles that are pointed by qInternalQProfile.
ROW qProfileRowStatus	1.3.6.1.4.1.164.6.3.11.1.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
qProfileTable	1.3.6.1.4.1.164.6.3.11.1		not-accessible	This table defines the profiles for a cluster of queues.
queueGroupEntry	1.3.6.1.4.1.164.6.3.11.3.1		not-accessible	A conceptual row where each row contains one Queue group.
STR queueGroupName	1.3.6.1.4.1.164.6.3.11.3.1.1	SnmpAdminString	not-accessible	Defines the Queue Group unique name.
U32 queueGroupPointToInternalQueue	1.3.6.1.4.1.164.6.3.11.3.1.8	Unsigned32	read-create	This attribute defines the internal queue whithin queueGroupPointToQBlock that is pointed by this Queue Block.
STR queueGroupPointToQBlock	1.3.6.1.4.1.164.6.3.11.3.1.7	SnmpAdminString	read-create	This attribute defines the Queue Block name of the next Queue Block level that is pointed by this Queue Block.
U32 queueGroupQBlockIdx	1.3.6.1.4.1.164.6.3.11.3.1.3	Unsigned32	not-accessible	This attribute holds the ID of the Queue Block. NA=2^32-1.
U32 queueGroupQBlockLevel	1.3.6.1.4.1.164.6.3.11.3.1.2	Unsigned32	not-accessible	This attribute holds the Level of the Queue Block .First level is 1. NA=2^32-1.
STR queueGroupQBlockName	1.3.6.1.4.1.164.6.3.11.3.1.9	SnmpAdminString	read-create	This attribute holds the name of the Queue Block.
U32 queueGroupQBlockProfile	1.3.6.1.4.1.164.6.3.11.3.1.5	Unsigned32	read-create	This attribute defines the Queue profile assigned to this Queue Block. This object points to qProfileIndex in qProfileTable.
U32 queueGroupQBlockShaperProfile	1.3.6.1.4.1.164.6.3.11.3.1.6	Unsigned32	read-create	This attribute defines the Shaper profile assigned to this Queue Block.
ROW queueGroupRowStatus	1.3.6.1.4.1.164.6.3.11.3.1.4	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
queueGroupTable	1.3.6.1.4.1.164.6.3.11.3		not-accessible	This table defines the queue groups/blocks,their level and connections between them.
queueProfileObjects	1.3.6.1.4.1.164.6.3.11
rad	1.3.6.1.4.1.164
radAce	1.3.6.1.4.1.164.6.1.12.3
radAce101	1.3.6.1.4.1.164.6.1.12.3.1
radAce102	1.3.6.1.4.1.164.6.1.12.3.2
radAce2002	1.3.6.1.4.1.164.6.1.12.2.6
radAce2002E	1.3.6.1.4.1.164.6.1.12.2.7
radAce2005	1.3.6.1.4.1.164.6.1.12.2.5
radAce201	1.3.6.1.4.1.164.6.1.12.3.7
radAce202	1.3.6.1.4.1.164.6.1.12.2.14
radAce20E	1.3.6.1.4.1.164.6.1.12.2.3
radAce20T	1.3.6.1.4.1.164.6.1.12.2.4
radAce2E	1.3.6.1.4.1.164.6.1.12.2.8
radAce2T	1.3.6.1.4.1.164.6.1.12.2.9
radAce3100	1.3.6.1.4.1.164.6.1.12.3.9
radAce3100PSN	1.3.6.1.4.1.164.6.1.12.3.12
radAce3105	1.3.6.1.4.1.164.6.1.12.3.18
radAce3200	1.3.6.1.4.1.164.6.1.12.3.8
radAce3200PSN	1.3.6.1.4.1.164.6.1.12.3.13
radAce3205	1.3.6.1.4.1.164.6.1.12.3.17
radAce3400	1.3.6.1.4.1.164.6.1.12.3.10
radAce3400PSN	1.3.6.1.4.1.164.6.1.12.3.14
radAce3402	1.3.6.1.4.1.164.6.1.12.3.11
radAce3402PSN	1.3.6.1.4.1.164.6.1.12.3.15
radAce3600	1.3.6.1.4.1.164.6.1.12.3.16
radAce50	1.3.6.1.4.1.164.6.1.12.3.3
radAce52	1.3.6.1.4.1.164.6.1.12.3.4
radAce52L	1.3.6.1.4.1.164.6.1.12.3.5
radAmc102	1.3.6.1.4.1.164.6.1.12.2.12
radAmc102c	1.3.6.1.4.1.164.6.1.12.2.13
radAmcdE1	1.3.6.1.4.1.164.6.1.12.2.1
radAmcdT1	1.3.6.1.4.1.164.6.1.12.2.2
radAPD2	1.3.6.1.4.1.164.6.1.8.6
radAPD8	1.3.6.1.4.1.164.6.1.8.7
radAPS16	1.3.6.1.4.1.164.6.1.8.9
radAPS24	1.3.6.1.4.1.164.6.1.8.10
radAPS8	1.3.6.1.4.1.164.6.1.8.8
radAsmi450R1152	1.3.6.1.4.1.164.6.1.3.47
radAsmi450R1152Sa	1.3.6.1.4.1.164.6.1.3.46
radAsmi450R768	1.3.6.1.4.1.164.6.1.3.45
radAsmi450R768Sa	1.3.6.1.4.1.164.6.1.3.44
radAsmi52A	1.3.6.1.4.1.164.6.1.3.99
radAsmi52L	1.3.6.1.4.1.164.6.1.3.121
radAsmi54	1.3.6.1.4.1.164.6.1.3.140
radAtm	1.3.6.1.4.1.164.12
radAtmCsuDsu	1.3.6.1.4.1.164.6.1.12.2
INT radBridgeAction	1.3.6.1.4.1.164.4.1.1	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the tables maintained by the network device. Send actions are not currently implemented. Not all actions can be performed on all bridges.
INT radBridgeAgingTime	1.3.6.1.4.1.164.4.1.9.5	INTEGER	read-write	This variable defines whether the Aging Time will be finite or infinite. When selecting the finite (3) value, the exact time will be determined by another variable of the standard MIB (ex. 1493.dot1dTpAgingTime). or by radBridgeAgingTime below.
INT radBridgeAgingTimeSec	1.3.6.1.4.1.164.4.1.9.4.1.4	INTEGER	read-write	This variable duplicates scalar object dot1dTpAgingTimeThe of BRIDGE-MIB with configuration index and Bridge index. It defines the timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
radBridgeCOD	1.3.6.1.4.1.164.4.1.4
INT radBridgeCODAnswerConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.5	INTEGER	read-write	CODCondAnswerConnect allows the user to specify the condition under which the link is connected. The options are: onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE .
radBridgeCODCondEntry	1.3.6.1.4.1.164.4.1.4.4.1		not-accessible	Each radBridgeCODCondEntry consists of the following parameters
I32 radBridgeCODCondIfIndex	1.3.6.1.4.1.164.4.1.4.4.1.1	Integer32	read-only	The interface, this COD entry is applicable to.
radBridgeCODCondTable	1.3.6.1.4.1.164.4.1.4.4		not-accessible	The table of COD Condition parameters
I32 radBridgeCODConnectDelay	1.3.6.1.4.1.164.4.1.4.1.1.4	Integer32	read-write	The connect delay defines the minimum time period that the link must stay disconnected, between 2 succesive connections (in seconds).
INT radBridgeCODDay	1.3.6.1.4.1.164.4.1.4.2.1.2	INTEGER	read-only	The day of the week in which the dial up connection operates.
I32 radBridgeCODDisConnectMinimunFramesNumber	1.3.6.1.4.1.164.4.1.4.4.1.7	Integer32	read-write	Frames rate.
radBridgeCODEntry	1.3.6.1.4.1.164.4.1.4.1.1		not-accessible	Each radBridgeCODEntry consists of the following parameters
I32 radBridgeCODIfIndex	1.3.6.1.4.1.164.4.1.4.1.1.1	Integer32	read-only	The interface to which this COD entry is applicable.
INT radBridgeCODImplicitSwitch	1.3.6.1.4.1.164.4.1.4.1.1.6	INTEGER	read-write	The inplicit switch allows the user to ignore implicit triggers provided by the COD software.
IP radBridgeCODIPMask	1.3.6.1.4.1.164.4.1.4.3.3	IpAddress	read-write	This is the Mask of the Remote IP Address
I32 radBridgeCODisConnectDelay	1.3.6.1.4.1.164.4.1.4.1.1.5	Integer32	read-write	The disconnect delay defines the minimum time period the link must stay connected, between 2 succesive disconnections (in seconds).
INT radBridgeCODManualConnect	1.3.6.1.4.1.164.4.1.4.1.1.2	INTEGER	read-write	The management station can start connection manually by setting this parameter
INT radBridgeCODMode	1.3.6.1.4.1.164.4.1.4.1.1.3	INTEGER	read-write	In answer mode only one incoming call may be accepted at a time. Other nodes attempting to access the local modem will receive a busy signal until the connection is terminated. (Answer mode has no difficulty supporting multiple remote connections to one local port, as blocking multiple incoming calls is just a modem function. Originate mode, on the other hand will only support a single local port to remote port connection). The disable parameter disables the COD utility for this interface. Choosing any other mode will enable the COD utility.
C32 radBridgeCODNumAccess	1.3.6.1.4.1.164.4.1.4.1.1.7	Counter32	read-only	The number of successful connections that have been established since the COD has been reset.
INT radBridgeCODOriginateConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.2	INTEGER	read-write	This condition, allows the user to specify the condition under which the link is connected. The options are onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=connect).
INT radBridgeCODOriginateDisConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.3	INTEGER	read-write	This condition allows the user to specify the condition under which the link is disconnected. The options are: noStationOnLan - When there is no station on lan. Counts 15 minutes from the point the last frame from lan has been received. If no frame have been transmitted on lan by the end of this period, disconnect the connection. onTraffic - On traffic. The user can specify the condition/s for disconnection. The disconnection will be defined in CODSpecificOnTrafficConditionOID . onDelayFromConnectionOnRequest - On Delay From Connection On Request . The delay time period will be defined in CODOriginateDisConnectDelay . onManualDisConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=disconnect).
I32 radBridgeCODOriginateDisConnectDelay	1.3.6.1.4.1.164.4.1.4.4.1.4	Integer32	read-write	Delay time in seconds.
radBridgeCODParamTable	1.3.6.1.4.1.164.4.1.4.1		not-accessible	The table of COD parameters
INT radBridgeCODProtocolType	1.3.6.1.4.1.164.4.1.4.3.1.1.1	INTEGER	read-only	The Protocol Type of the Traffic Table
IP radBridgeCODRemoteIPAddr	1.3.6.1.4.1.164.4.1.4.3.2	IpAddress	read-write	This is the Remote IP Address
OID radBridgeCODSpecificOnTrafficOIDCondition	1.3.6.1.4.1.164.4.1.4.4.1.6	OBJECT IDENTIFIER	read-only	A reference to a specific entry in the radBridgeMaskTable, which describes the particular COD condition . If Connect or Disconnect Conditions are not onTraffic, its value should be set to the OBJECT IDENTIFIER { 0 0 }.
I32 radBridgeCODTimeIfIndex	1.3.6.1.4.1.164.4.1.4.2.1.1	Integer32	read-only	The interface to which this COD Time Trigger entry is applicable.
radBridgeCODTimeTriggerEntry	1.3.6.1.4.1.164.4.1.4.2.1		not-accessible	Each radBridgeCODTimeTriggerEntry consists of the following parameters
STR radBridgeCODTimeTriggerFrom	1.3.6.1.4.1.164.4.1.4.2.1.4	DisplayString	read-write	Time to start Dial Up connection, in format hh:mm.
I32 radBridgeCODTimeTriggerNum	1.3.6.1.4.1.164.4.1.4.2.1.3	Integer32	read-only	Every day of the week the user can configure 3 dial up connections.
INT radBridgeCODTimeTriggerStatus	1.3.6.1.4.1.164.4.1.4.2.1.6	INTEGER	read-write	The status of a table entry.
radBridgeCODTimeTriggerTable	1.3.6.1.4.1.164.4.1.4.2		not-accessible	The table of COD parameters
STR radBridgeCODTimeTriggerTo	1.3.6.1.4.1.164.4.1.4.2.1.5	DisplayString	read-write	Time to terminate Dial Up connection, in format HH:MM.
I32 radBridgeCODTotalConnecTime	1.3.6.1.4.1.164.4.1.4.1.1.8	Integer32	read-only	The sum of all the connect time intervals since the COD was reset.
radBridgeCODTraffic	1.3.6.1.4.1.164.4.1.4.3
radBridgeCODTrafficEntry	1.3.6.1.4.1.164.4.1.4.3.1.1		not-accessible	Each radBridgeCODTrafficEntry consists of the following parameters.
radBridgeCODTrafficTable	1.3.6.1.4.1.164.4.1.4.3.1		not-accessible	The table of COD Traffic trigger
OCT radBridgeCODTrafficTriggerProtType	1.3.6.1.4.1.164.4.1.4.3.4	OCTET STRING	read-write	Protocol Type for the User Defined Protocol Traffic Trigger (3).
INT radBridgeCODTrafficTriggerStatus	1.3.6.1.4.1.164.4.1.4.3.1.1.2	INTEGER	read-write	Command of Status of the Protocol Traffic Trigger
radBridgeCurrentEntry	1.3.6.1.4.1.164.4.1.7.1.1		not-accessible	An entry in the RAD Bridge Current table.
G32 radBridgeCurrentFrameTypeDiscardedFrames	1.3.6.1.4.1.164.4.1.7.1.1.3	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in the current 15 minute interval.
I32 radBridgeCurrentIndex	1.3.6.1.4.1.164.4.1.7.1.1.1	Integer32	read-only	The index of the Bridge interface or Bridge Port. It may be ifIndex.
G32 radBridgeCurrentIngressFilteringDiscardedFrames	1.3.6.1.4.1.164.4.1.7.1.1.2	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in the current 15 minute interval.
G32 radBridgeCurrentRxBcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.7	Gauge32	read-only	The counter associated with the number of Received Broadcast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxCorrectBytes	1.3.6.1.4.1.164.4.1.7.1.1.5	Gauge32	read-only	The counter associated with the number of Received Correct Bytes, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.1.1.6	Gauge32	read-only	The counter associated with the number of times the associated radBridgeCurrentRxCorrectBytes counter has overflowed.
G32 radBridgeCurrentRxCorrectFrames	1.3.6.1.4.1.164.4.1.7.1.1.4	Gauge32	read-only	The counter associated with the number of Received Correct Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxMcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.8	Gauge32	read-only	The counter associated with the number of Received Multicast Frames, encountered by a Bridge Port in the current 15 minute interval.
radBridgeCurrentTable	1.3.6.1.4.1.164.4.1.7.1		not-accessible	The RAD Bridge Current table.
G32 radBridgeCurrentTxBcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.12	Gauge32	read-only	The counter associated with the number of Transmitted Broadcast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxCorrectBytes	1.3.6.1.4.1.164.4.1.7.1.1.10	Gauge32	read-only	The counter associated with the number of Transmitted Correct Bytes, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.1.1.11	Gauge32	read-only	The counter associated with the number of times the associated radBridgeCurrentTxCorrectBytes counter has overflowed.
G32 radBridgeCurrentTxCorrectFrames	1.3.6.1.4.1.164.4.1.7.1.1.9	Gauge32	read-only	The counter associated with the number of Transmitted Correct Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxDropFrames	1.3.6.1.4.1.164.4.1.7.1.1.14	Gauge32	read-only	The counter associated with the number of Transmitted Dropped Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxMcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.13	Gauge32	read-only	The counter associated with the number of Transmitted Multicast Frames, encountered by a Bridge Port in the current 15 minute interval.
INT radBridgeDot1qVlanSplitHorizon	1.3.6.1.4.1.164.4.1.9.2.1.3	INTEGER	read-create	When 'enable (3)', packets having this VLAN will not be switched back to other bridge ports which are members of this VLAN.
radBridgeDot1qVlanStaticEntry	1.3.6.1.4.1.164.4.1.9.2.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
radBridgeDot1qVlanStaticTable	1.3.6.1.4.1.164.4.1.9.2		not-accessible	A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
POR radBridgeDot1qVlanTaggedPorts	1.3.6.1.4.1.164.4.1.9.2.1.1	PortList	read-create	The set of ports which should transmit egress packets for this VLAN as tagged.
POR radBridgeDot1qVlanUnmodifiedPorts	1.3.6.1.4.1.164.4.1.9.2.1.2	PortList	read-create	The set of ports which should transmit egress packets for this VLAN as unmodified.
U32 radBridgeEthType	1.3.6.1.4.1.164.4.1.9.4.1.8	Unsigned32	read-write	Value of Ethertype field in Ethernet frame. This field indicates which protocol is being transported in an ethernet frame.
INT radBridgeForwardingMode	1.3.6.1.4.1.164.4.1.12	INTEGER	read-write	This object determines the Bridge Forwarding Mode: transparent - Forward all frames received (not dependent on VLAN). filter - Filter frames received according to MAC Address. filterTagged = Filter frames received according to VLAN. transparentTagged = VLAN aware + Transparent.
INT radBridgeGenCfgBridgeAction	1.3.6.1.4.1.164.4.1.9.4.1.3	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the tables maintained by the Bridge. After performing the action, Agent will automatically Set the value of this variable to noOp(255).
radBridgeGenCfgEntry	1.3.6.1.4.1.164.4.1.9.4.1		not-accessible	Describes an entry in the radBridgeGenCfgTable.
I32 radBridgeGenCfgIdx	1.3.6.1.4.1.164.4.1.9.4.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg. For Agents that support only one Configuration, this object will be constant=1.
I32 radBridgeGenCfgIdx2	1.3.6.1.4.1.164.4.1.9.4.1.2	Integer32	not-accessible	For Agents having more than one bridge, this index may be used as bridge index
radBridgeGenCfgTable	1.3.6.1.4.1.164.4.1.9.4		not-accessible	A table containing Bridge configuration parameters.
radBridgeGenCnfg	1.3.6.1.4.1.164.4.1.9
INT radBridgeGenFlowBasicClassification	1.3.6.1.4.1.164.4.1.9.1.1.7	INTEGER	read-create	This object defines whether Classification based on Port should be taken into account (either as default, or in addition to other classifications).
I32 radBridgeGenFlowBroadcastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.9	Integer32	read-create	The Traffic Class the received Broadcast frame is mapped to.
I32 radBridgeGenFlowCnfgIdx	1.3.6.1.4.1.164.4.1.9.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.
radBridgeGenFlowEntry	1.3.6.1.4.1.164.4.1.9.1.1		not-accessible	Static information for a Bridge configured into the device by management.
I32 radBridgeGenFlowFloodOrBcastMaxRate	1.3.6.1.4.1.164.4.1.9.1.1.4	Integer32	read-create	This object controls maximum Flooding or Broadcast Rate: Max number of multicast along with unknown or flooded unicast frames allowed to enter any port. The number can be presented either as percentage of bandwidth, or bandwidth in Kbps. Once the limit is exceeded, any multicast or flooded frame entering from the port is discarded For RIC-155, and FCD-155 valid values are 3% , 6%, 12% and 100% = No Limit
I32 radBridgeGenFlowIdx	1.3.6.1.4.1.164.4.1.9.1.1.2	Integer32	not-accessible	For Agent having more than one bridge, this index may be used as bridge index
I32 radBridgeGenFlowMulticastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.8	Integer32	read-create	The Traffic Class the received Multicast frame is mapped to.
INT radBridgeGenFlowQosMode	1.3.6.1.4.1.164.4.1.9.1.1.5	INTEGER	read-create	This object controls Quality of Service mode. User may select which field(s) (in case of fields - which one has precedence) will affect prioritization of data between egress queues.
ROW radBridgeGenFlowRowStatus	1.3.6.1.4.1.164.4.1.9.1.1.3	RowStatus	read-create	This object enable user to create/delete entries in this table.
INT radBridgeGenFlowSchedulingMode	1.3.6.1.4.1.164.4.1.9.1.1.6	INTEGER	read-create	This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme, Strict Priority (SP) or ATM CoS
radBridgeGenFlowTable	1.3.6.1.4.1.164.4.1.9.1		not-accessible	A table containing static configuration information for Bridge configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
I32 radBridgeGenFlowUnkownUnicastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.10	Integer32	read-create	The Traffic Class the received Unkonwn Unicast frame is mapped to.
I32 radBridgeInactiveArpTimeOut	1.3.6.1.4.1.164.4.1.2	Integer32	read-write	This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
radBridgeIntervalEntry	1.3.6.1.4.1.164.4.1.7.2.1		not-accessible	An entry in the RAD Bridge Interval table.
G32 radBridgeIntervalFrameTypeDiscardedFrames	1.3.6.1.4.1.164.4.1.7.2.1.4	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals.
I32 radBridgeIntervalIndex	1.3.6.1.4.1.164.4.1.7.2.1.1	Integer32	read-only	The index of the bridge interface or Bridge Port. It may be ifIndex.
G32 radBridgeIntervalIngressFilteringDiscardedFrames	1.3.6.1.4.1.164.4.1.7.2.1.3	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals.
I32 radBridgeIntervalNumber	1.3.6.1.4.1.164.4.1.7.2.1.2	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
G32 radBridgeIntervalRxBcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.8	Gauge32	read-only	The counter associated with the number of Received Broadcast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxCorrectBytes	1.3.6.1.4.1.164.4.1.7.2.1.6	Gauge32	read-only	The counter associated with the number of Received Correct Bytes, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.2.1.7	Gauge32	read-only	The counter associated with the number of times the associated radBridgeIntervalRxCorrectBytes counter has overflowed.
G32 radBridgeIntervalRxCorrectFrames	1.3.6.1.4.1.164.4.1.7.2.1.5	Gauge32	read-only	The counter associated with the number of Received Correct Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxMcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.9	Gauge32	read-only	The counter associated with the number of Received Multicast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
radBridgeIntervalTable	1.3.6.1.4.1.164.4.1.7.2		not-accessible	The RAD Bridge Interval table.
G32 radBridgeIntervalTxBcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.13	Gauge32	read-only	The counter associated with the number of Transmitted Broadcast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxCorrectBytes	1.3.6.1.4.1.164.4.1.7.2.1.11	Gauge32	read-only	The counter associated with the number of Transmitted Correct Bytes, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.2.1.12	Gauge32	read-only	The counter associated with the number of times the associated radBridgeIntervalTxCorrectBytes counter has overflowed.
G32 radBridgeIntervalTxCorrectFrames	1.3.6.1.4.1.164.4.1.7.2.1.10	Gauge32	read-only	The counter associated with the number of Transmitted Correct Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxDropFrames	1.3.6.1.4.1.164.4.1.7.2.1.15	Gauge32	read-only	The counter associated with the number of Transmitted Dropped Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxMcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.14	Gauge32	read-only	The counter associated with the number of Transmitted Multicast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
I32 radBridgeInvBasePort	1.3.6.1.4.1.164.4.1.10.1.1.2	Integer32	read-only	The Bridge port number.
radBridgeInvBasePortEntry	1.3.6.1.4.1.164.4.1.10.1.1		not-accessible	The bridge port number for each bridge port interface index.
I32 radBridgeInvBasePortIfIndex	1.3.6.1.4.1.164.4.1.10.1.1.1	Integer32	read-only	The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this Bridge port.
radBridgeInvBasePortTable	1.3.6.1.4.1.164.4.1.10.1		not-accessible	An inversed table to dot1dBasePortTable from RFC1493 with reduced information. This table index is known to the NMS and this way the needed information can be received by just one Get command, instead of searching the entire dot1dBasePortTable (where it is an attribute).
radBridgeIPX	1.3.6.1.4.1.164.4.1.5
radBridgeIPXdriver	1.3.6.1.4.1.164.4.1.5.1
INT radBridgeIPXForwarding	1.3.6.1.4.1.164.4.1.5.1.1	INTEGER	read-write	The indication of whether this entity is acting as an IPX gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IPX gateways forward datagrams. IPX hosts do not. Note that changing this parameter requiers RESET of the router.
radBridgeIPXRip	1.3.6.1.4.1.164.4.1.5.2
TIK radBridgeIPXRipAgingTime	1.3.6.1.4.1.164.4.1.5.2.6.1.7	TimeTicks	read-only	The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.
OCT radBridgeIPXRipDestNetwork	1.3.6.1.4.1.164.4.1.5.2.6.1.1	OCTET STRING	read-only	The destination network address to which this entry's routing information pertains.
OCT radBridgeIPXRipForwardingRouter	1.3.6.1.4.1.164.4.1.5.2.6.1.3	OCTET STRING	read-write	The IPX node address of the next hop (router) for the entry's associated destination network.
INT radBridgeIPXRipForwardType	1.3.6.1.4.1.164.4.1.5.2.6.1.9	INTEGER	read-write	The type of route. Note that local(2) refers to a route for which the next hop is the final destination; remote(3) refers to a route for which the next hop is not the final destination.
I32 radBridgeIPXRipHopMetric	1.3.6.1.4.1.164.4.1.5.2.6.1.6	Integer32	read-write	The metric, in terms of distance , associated with the route given by the entry.
C32 radBridgeIPXRipInDiscards	1.3.6.1.4.1.164.4.1.5.2.3	Counter32	read-only	The number of received packets discarded by RIP.
I32 radBridgeIPXRipInfAgeMultiplier	1.3.6.1.4.1.164.4.1.5.2.7.1.3	Integer32	read-write	The holding multiplier for information received in RIP periodic updates. Zero value corresponds to infinite aging time.
I32 radBridgeIPXRipInfBcastUpdate	1.3.6.1.4.1.164.4.1.5.2.7.1.2	Integer32	read-write	The RIP periodic update interval, in seconds. Zero value corresponds to infinite interval.
radBridgeIPXRipInfEntry	1.3.6.1.4.1.164.4.1.5.2.7.1		not-accessible	Each entry corresponds to one ifindex.
I32 radBridgeIPXRipInfIfIndex	1.3.6.1.4.1.164.4.1.5.2.7.1.1	Integer32	read-only	This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.
radBridgeIPXRipInfTable	1.3.6.1.4.1.164.4.1.5.2.7		not-accessible	The RIP interface table.
C32 radBridgeIPXRipInPackets	1.3.6.1.4.1.164.4.1.5.2.2	Counter32	read-only	The total number of packets received by RIP. This will include any packets that are subsequently discarded.
I32 radBridgeIPXRipNIC	1.3.6.1.4.1.164.4.1.5.2.6.1.4	Integer32	read-write	An interface identifier specifying what IPX interface the next hop can be found on.
C32 radBridgeIPXRipOutPackets	1.3.6.1.4.1.164.4.1.5.2.1	Counter32	read-only	The total number of packets transmitted by RIP.
INT radBridgeIPXRipPolicy	1.3.6.1.4.1.164.4.1.5.2.6.1.2	INTEGER	read-only	A value specifying the precidence of the route. A value of zero means that the route is the best route, a value of one means that the route is the second best route and so on.
radBridgeIPXRipTable	1.3.6.1.4.1.164.4.1.5.2.6		not-accessible	The routing table used by RIP to calculate routes to remote desination networks.
radBridgeIPXRipTableEntry	1.3.6.1.4.1.164.4.1.5.2.6.1		not-accessible	The routing information for one of this entity's destination networks.
I32 radBridgeIPXRipTblBcastTrigUpdateInterval	1.3.6.1.4.1.164.4.1.5.2.5	Integer32	read-write	The default time interval (in seconds)between triggered RIP updates on a broadcast type interface. A triggered update occurs when a change is detected in the routing database. This time interval delays the broadcasting of these updates so that changes on the network will not result in a lot of triggered updates.
I32 radBridgeIPXRipTblNoOfEntries	1.3.6.1.4.1.164.4.1.5.2.4	Integer32	read-only	The max number of entries that exist in the RIP routing table.
I32 radBridgeIPXRipTickMetric	1.3.6.1.4.1.164.4.1.5.2.6.1.5	Integer32	read-write	The metric, in terms of transit time, associated with the route given by the entry. This time is in terms of 1/18ths of a second.
INT radBridgeIPXRipValueStatus	1.3.6.1.4.1.164.4.1.5.2.6.1.8	INTEGER	read-write	The entry status value; whether the entry is permanent (added statically), reachable or unreachable. In the latter two cases it would be added by RIP. A semiDynamic entry is an entry enterd manualy by the user and can be updated by the router.
radBridgeIPXSap	1.3.6.1.4.1.164.4.1.5.3
TIK radBridgeIPXSapAgingTime	1.3.6.1.4.1.164.4.1.5.3.6.1.8	TimeTicks	read-only	The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.
I32 radBridgeIPXSapHopsToServer	1.3.6.1.4.1.164.4.1.5.3.6.1.6	Integer32	read-write	The number of hops to the entity on which this server exists.
C32 radBridgeIPXSapInDiscards	1.3.6.1.4.1.164.4.1.5.3.3	Counter32	read-only	The number of received packets discarded by SAP.
I32 radBridgeIPXSapInfAgeMultiplier	1.3.6.1.4.1.164.4.1.5.3.7.1.3	Integer32	read-write	The holding multiplier for information received in SAP periodic updates. Zero value corresponds to infinite aging time.
I32 radBridgeIPXSapInfBcastUpdate	1.3.6.1.4.1.164.4.1.5.3.7.1.2	Integer32	read-write	The SAP periodic update interval, in seconds. Zero value corresponds to infinite interval.
radBridgeIPXSapInfEntry	1.3.6.1.4.1.164.4.1.5.3.7.1		not-accessible	Each entry corresponds to one ifindex.
I32 radBridgeIPXSapInfIfIndex	1.3.6.1.4.1.164.4.1.5.3.7.1.1	Integer32	read-only	This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.
radBridgeIPXSapInfTable	1.3.6.1.4.1.164.4.1.5.3.7		not-accessible	The Sap interface table.
C32 radBridgeIPXSapInPackets	1.3.6.1.4.1.164.4.1.5.3.2	Counter32	read-only	The total number of packets received by SAP. This will include any packets that are subsequently discarded.
STR radBridgeIPXSapName	1.3.6.1.4.1.164.4.1.5.3.6.1.2	DisplayString	read-only	The name of the server for which this entry pertains.
OCT radBridgeIPXSapNetwork	1.3.6.1.4.1.164.4.1.5.3.6.1.3	OCTET STRING	read-write	The IPX network address of the host on which this server exists.
I32 radBridgeIPXSapNIC	1.3.6.1.4.1.164.4.1.5.3.6.1.7	Integer32	read-write	An Network Interface Card identifier specifying what IPX interface the next hop can be found on.
OCT radBridgeIPXSapNode	1.3.6.1.4.1.164.4.1.5.3.6.1.4	OCTET STRING	read-write	The IPX node address of the host on which this server exists.
C32 radBridgeIPXSapOutPackets	1.3.6.1.4.1.164.4.1.5.3.1	Counter32	read-only	The total number of packets transmitted by SAP.
I32 radBridgeIPXSapServerType	1.3.6.1.4.1.164.4.1.5.3.6.1.1	Integer32	read-only	The type of the server for which this entry pertains.
I32 radBridgeIPXSapSocket	1.3.6.1.4.1.164.4.1.5.3.6.1.5	Integer32	read-write	The IPX socket number that is being used by the server to which this entry pertains.
INT radBridgeIPXSapStatus	1.3.6.1.4.1.164.4.1.5.3.6.1.9	INTEGER	read-write	The status of the entry.
radBridgeIPXSapTable	1.3.6.1.4.1.164.4.1.5.3.6		not-accessible	The Server Information table is used by SAP to store information of services which are available on the internetwork.
radBridgeIPXSapTableEntry	1.3.6.1.4.1.164.4.1.5.3.6.1		not-accessible	The server information for one of this entity's server entries.
I32 radBridgeIPXSapTblBcastTrigUpdateInterval	1.3.6.1.4.1.164.4.1.5.3.5	Integer32	read-write	The default time interval (in seconds) between triggered SAP updates on a broadcast style interface. A triggered update occurs when a change is detected in the service database. This time interval delays the transmission of these updates so that changes on the network will not result in a lot of triggered updates.
I32 radBridgeIPXSapTblNoOfEntries	1.3.6.1.4.1.164.4.1.5.3.4	Integer32	read-only	The max number of entries that exist in the SAP Server Information table.
U32 radBridgeLoopDetectVlanId	1.3.6.1.4.1.164.4.1.9.4.1.6	Unsigned32	read-write	This variable indicates the VLAN ID used for Loop Detection packets. Valid values: 1 - 4095: VLAN ID 0 - Means that the Loop Detection is Disabled.
OCT radBridgeMaskActiveBit1	1.3.6.1.4.1.164.4.1.3.1.6	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat1 field.
OCT radBridgeMaskActiveBit2	1.3.6.1.4.1.164.4.1.3.1.11	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat2 field.
OCT radBridgeMaskActiveBit3	1.3.6.1.4.1.164.4.1.3.1.16	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat3 field.
INT radBridgeMaskCond1	1.3.6.1.4.1.164.4.1.3.1.9	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that matches the content of radBridgeMaskPat1. false - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that does not match the content of radBridgeMaskPat1.
INT radBridgeMaskCond2	1.3.6.1.4.1.164.4.1.3.1.14	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that matches the content of radBridgeMaskPat2. false - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that does not match the content of radBridgeMaskPat2.
INT radBridgeMaskCond3	1.3.6.1.4.1.164.4.1.3.1.19	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that matches the content of radBridgeMaskPat3 false - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that does not match the content of radBridgeMaskPat3.
INT radBridgeMaskDest	1.3.6.1.4.1.164.4.1.3.1.4	INTEGER	read-write	Specifies the type of destination address carried by the frame to which the mask will be applied. Unassigned-condition deactivates the mask entry.
radBridgeMaskEntry	1.3.6.1.4.1.164.4.1.3.1		not-accessible	An entry in table radBridgeMaskTable.
INT radBridgeMaskFrom1	1.3.6.1.4.1.164.4.1.3.1.7	INTEGER	read-write	Offset base of radBridgeMaskPat1 within the frame. Net can be in some cases the data start point.
INT radBridgeMaskFrom2	1.3.6.1.4.1.164.4.1.3.1.12	INTEGER	read-write	Offset base of radBridgeMaskPat2 within the frame. Net can be in some cases the data start point.
INT radBridgeMaskFrom3	1.3.6.1.4.1.164.4.1.3.1.17	INTEGER	read-write	Offset base of radBridgeMaskPat3 within the frame. Net can be in some cases the data start point.
I32 radBridgeMaskIfIndex	1.3.6.1.4.1.164.4.1.3.1.2	Integer32	read-only	Specifies the if Index of the interface to which the mask is applied.
I32 radBridgeMaskNum	1.3.6.1.4.1.164.4.1.3.1.3	Integer32	read-only	The Mask entry number, defined by its line number in the mask table.
I32 radBridgeMaskOffset1	1.3.6.1.4.1.164.4.1.3.1.8	Integer32	read-write	Specifies the radBridgeMaskPat1 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm1.The mask offset is an even decimal number in the range of 0 to 1518.
I32 radBridgeMaskOffset2	1.3.6.1.4.1.164.4.1.3.1.13	Integer32	read-write	Specifies the radBridgeMaskPat2 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm2.The mask offset is an even decimal number in the range of 0 to 1518.
I32 radBridgeMaskOffset3	1.3.6.1.4.1.164.4.1.3.1.18	Integer32	read-write	Specifies the radBridgeMaskPat3 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm3. The mask offset is an even decimal number in the range of 0 to 1518.
INT radBridgeMaskOper	1.3.6.1.4.1.164.4.1.3.1.20	INTEGER	read-write	The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list.
OCT radBridgeMaskPat1	1.3.6.1.4.1.164.4.1.3.1.5	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
OCT radBridgeMaskPat2	1.3.6.1.4.1.164.4.1.3.1.10	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
OCT radBridgeMaskPat3	1.3.6.1.4.1.164.4.1.3.1.15	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
radBridgeMaskTable	1.3.6.1.4.1.164.4.1.3		not-accessible	Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement consisting of up to three mask definitions and an action defined by radBridgeMaskOper. Different types of mask entries are supported, as defined by radBridgeMaskType.
INT radBridgeMaskType	1.3.6.1.4.1.164.4.1.3.1.1	INTEGER	read-only	Defines the type of mask entry.
INT radBridgeMngFlow	1.3.6.1.4.1.164.4.1.9.6	INTEGER	read-write	This variable defines whether the Management Flow is passed through the bridge (enable) or not (disable).
U32 radBridgeMngVlanId	1.3.6.1.4.1.164.4.1.9.4.1.5	Unsigned32	read-write	This variable indicates the VLAN ID used for remote management traffic. 0 = Not Applicable.
radBridgePerformance	1.3.6.1.4.1.164.4.1.7
radBridgePort	1.3.6.1.4.1.164.4.1.13
radBridgePortBaseVlan	1.3.6.1.4.1.164.4.1.8
I32 radBridgePortBaseVlanCnfgIdx	1.3.6.1.4.1.164.4.1.8.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
POR radBridgePortBaseVlanEgressPorts	1.3.6.1.4.1.164.4.1.8.1.1.4	PortList	read-create	The set of ports which are permanently assigned to the egress list for this port based VLAN by management. The default value of this object is a string of zeros.
radBridgePortBaseVlanEntry	1.3.6.1.4.1.164.4.1.8.1.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
I32 radBridgePortBaseVlanIdx	1.3.6.1.4.1.164.4.1.8.1.1.2	Integer32	not-accessible	Index of the port based VLAN.
INT radBridgePortBaseVlanMng	1.3.6.1.4.1.164.4.1.8.1.1.7	INTEGER	read-create	This object allows user to enable/disable management traffic on this VLAN. disable - only non-management data is allowed. enable - mixture of management traffic 0with other types of data is allowed.
STR radBridgePortBaseVlanName	1.3.6.1.4.1.164.4.1.8.1.1.3	SnmpAdminString	read-create	An administratively assigned string, which may be used to identify the the port based VLAN.
ROW radBridgePortBaseVlanRowStatus	1.3.6.1.4.1.164.4.1.8.1.1.6	RowStatus	read-create	This object enable user to create/delete entries in this table.
radBridgePortBaseVlanTable	1.3.6.1.4.1.164.4.1.8.1		not-accessible	A table containing static configuration information for each VLAN configured into the device by management. All entries are permanent and will be restored after the device is reset.
POR radBridgePortBaseVlanVirtualGroups	1.3.6.1.4.1.164.4.1.8.1.1.5	PortList	read-create	The set of Virtual Groups which are permanently assigned to this port based VLAN by management. (read Virtual Group instead of port in PortList Textual Convention) The default value of this object is a string of zeros.
I32 radBridgePortCnfgDefaultVci	1.3.6.1.4.1.164.4.1.13.1.1.7	Integer32	read-write	This object indicates the VCI of this Bridge Port's Default VCL. An incoming frame with priority that is not assigned to any VCL will be transferred to the Default VCL.
I32 radBridgePortCnfgDefaultVpi	1.3.6.1.4.1.164.4.1.13.1.1.6	Integer32	read-write	This object indicates the VPI of this Bridge Port's Default VCL. An incoming frame with priority that is not assigned to any VCL will be transferred to the Default VCL.
INT radBridgePortCnfgDot1x	1.3.6.1.4.1.164.4.1.13.1.1.11	INTEGER	read-write	This feature is currently supported via the variable ethIfTable.ethDot1xEnable. Determnines if the Port-Based Network Access Protocol (IEEE-802.1x)is enabled for the bridge Port.
I32 radBridgePortCnfgEgressMtu	1.3.6.1.4.1.164.4.1.13.1.1.10	Integer32	read-write	The size of the largest packet which can be sent on the interface, specified in octets.
radBridgePortCnfgEntry	1.3.6.1.4.1.164.4.1.13.1.1		not-accessible	An entry in the table.
I32 radBridgePortCnfgIdx	1.3.6.1.4.1.164.4.1.13.1.1.1	Integer32	not-accessible	The first index of the table. It can serve for Configuration index, Bridge index or other.
I32 radBridgePortCnfgIngressMtu	1.3.6.1.4.1.164.4.1.13.1.1.9	Integer32	read-write	The size of the largest packet which can be received on the interface, specified in octets.
I32 radBridgePortCnfgMaxMacAddr	1.3.6.1.4.1.164.4.1.13.1.1.3	Integer32	read-write	This object indicates the maximum number of total MAC Addresses (static and learned) supported by this Bridge Port.
INT radBridgePortCnfgMcastMode	1.3.6.1.4.1.164.4.1.13.1.1.5	INTEGER	read-write	This object indicates this Bridge Port's Multicast Mode: flooding (1) - flood multicast MAC addresses forwarding (2) - forward multicast MAC addresses to the subnet indicated.
INT radBridgePortCnfgMngFlow	1.3.6.1.4.1.164.4.1.13.1.1.4	INTEGER	read-write	This object indicates whether this Bridge Port is dedicated for management flow.
I32 radBridgePortCnfgPrtIdx	1.3.6.1.4.1.164.4.1.13.1.1.2	Integer32	not-accessible	This object indicates the Bridge Port index.
I32 radBridgePortCnfgStatVlanId	1.3.6.1.4.1.164.4.1.13.1.1.8	Integer32	read-write	This object indicates the selected VlanId of the bridge port on which statistics are being collected. 0=no Statistics collected for VLAN on this bridge port.
radBridgePortCnfgTable	1.3.6.1.4.1.164.4.1.13.1		not-accessible	The Bridge Port Configuration Table.
I32 radBridgePortVlanMemberBridgeIdx	1.3.6.1.4.1.164.4.1.8.2.1.1	Integer32	read-only	This object indicates the Bridge Index.
radBridgePortVlanMemberEntry	1.3.6.1.4.1.164.4.1.8.2.1		not-accessible	An entry in the Bridge Ports-VLANs Memebership table.
I32 radBridgePortVlanMemberPortIdx	1.3.6.1.4.1.164.4.1.8.2.1.2	Integer32	read-only	This object indicates the Bridge's Port Index. For some cases, it can be used as the Port ofIndex.
ROW radBridgePortVlanMemberRowStatus	1.3.6.1.4.1.164.4.1.8.2.1.4	RowStatus	read-create	This object enables the user to create/delete entries in this table.
radBridgePortVlanMemberTable	1.3.6.1.4.1.164.4.1.8.2		not-accessible	The Bridge Ports-VLAN Membership table. This table enables the user to assign: - Several VLANs to a Port. - Several Ports to a VLAN.
I32 radBridgePortVlanMemberVlanId	1.3.6.1.4.1.164.4.1.8.2.1.3	Integer32	read-only	This object indicates the VLAN ID.
radBridges	1.3.6.1.4.1.164.4
INT radBridgeSplitHorizon	1.3.6.1.4.1.164.4.1.9.4.1.7	INTEGER	read-write	This object configure 'split horizon' switching between bridge Ports. - disable - normal (VLAN aware) bridge behavior. - enable - all packets, regardless their VLAN, coming from user side are blocked from being switched back to other user side bridge ports. - vlanBased - split horizon behavior is applicable only for specific VLANs, according to radBridgeDot1qVlanSplitHorizon.
radBridgeStatus	1.3.6.1.4.1.164.4.1.10
radBridgeStp	1.3.6.1.4.1.164.4.1.11
radBridgeStpCnfgEntry	1.3.6.1.4.1.164.4.1.11.1.1		not-accessible	An entry in the radBridgeStpCnfgTable.
TIM radBridgeStpCnfgForwardDelay	1.3.6.1.4.1.164.4.1.11.1.1.3	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for Forward Delay when this bridge is acting as the root. Note that the range for this parameter is related to the value of radBridgeStpCnfgMaxAge (according to 802.1D-1990 for the similar scalars of BRIDGE-MIB). The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM radBridgeStpCnfgHelloTime	1.3.6.1.4.1.164.4.1.11.1.1.5	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for Hello Time when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
I32 radBridgeStpCnfgIdx1	1.3.6.1.4.1.164.4.1.11.1.1.1	Integer32	not-accessible	This object indicates the Index of the Agent Configuration the following objects refer to. For Agents that support more than one configuration: 255=Temporary Cnfg ; Set can be done only to this configuration. For Agents that support only one configuration, this object will be constant=1.
I32 radBridgeStpCnfgIdx2	1.3.6.1.4.1.164.4.1.11.1.1.2	Integer32	not-accessible	For Agents having the table objects per Card/Bridge/Interface this will be the index of the Card/Bridge/Interface used.
TIM radBridgeStpCnfgMaxAge	1.3.6.1.4.1.164.4.1.11.1.1.4	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for MaxAge when this bridge is acting as the root. Note that the range for this parameter is related to the value of radBridgeStpCnfgHelloTime (according to 802.1D-1990 for the similar scalars of BRIDGE-MIB). The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
I32 radBridgeStpCnfgPriority	1.3.6.1.4.1.164.4.1.11.1.1.6	Integer32	read-write	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID, per radBridgeStpCnfgIdx2 instance.
INT radBridgeStpCnfgStpVersion	1.3.6.1.4.1.164.4.1.11.1.1.7	INTEGER	read-write	This object determines the STP version used: stp - usual Spanning Tree Protocol. rstp - Rapid Spanning Tree Protocol.
radBridgeStpCnfgTable	1.3.6.1.4.1.164.4.1.11.1		not-accessible	STP Configuration table. STP=Spanning Tree Protocol. It includes STP configurable parameters that in BRIDGE-MIB are scalars, while we need them per card/bridge/interface and per different configurations.
BRI radBridgeStpStatDesignatedRoot	1.3.6.1.4.1.164.4.1.11.2.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
radBridgeStpStatEntry	1.3.6.1.4.1.164.4.1.11.2.1		not-accessible	An entry in the radBridgeStpStatTable.
TIM radBridgeStpStatForwardDelay	1.3.6.1.4.1.164.4.1.11.2.1.2	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to radBridgeStpCnfgForwardDelay which is the value that this bridge would start using if/when this bridge were to become the root.]
TIM radBridgeStpStatHelloTime	1.3.6.1.4.1.164.4.1.11.2.1.4	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
I32 radBridgeStpStatIdx	1.3.6.1.4.1.164.4.1.11.2.1.1	Integer32	not-accessible	For Agents having the table objects per Card/Bridge/Interface this will be the index of the Card/Bridge/Interface used.
TIM radBridgeStpStatMaxAge	1.3.6.1.4.1.164.4.1.11.2.1.3	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
I32 radBridgeStpStatRootCost	1.3.6.1.4.1.164.4.1.11.2.1.6	Integer32	read-only	The cost of the path to the root as seen from this bridge.
radBridgeStpStatTable	1.3.6.1.4.1.164.4.1.11.2		not-accessible	STP Status table. STP=Spanning Tree Protocol. It includes STP status parameters that in BRIDGE-MIB are scalars, while we need them per card/bridge/interface. For devices that have several configurations, this table is for Status of the Active configuration.
radConverters	1.3.6.1.4.1.164.5
INT radDot1qPortCopyOriginVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.2	INTEGER	read-write	This object indicates whether use the original VLAN Priority of the frame, as the priority of the VLAN added by this port.
I32 radDot1qPortDefaultVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.3	Integer32	read-write	Default VLAN Frame priority of the VLAN added by this port.
INT radDot1qPortEgressTagHandling	1.3.6.1.4.1.164.4.1.9.3.1.5	INTEGER	read-write	This object indicates how is the Egress VLAN Tag processed. It is mainly for use with Double Tagging.
INT radDot1qPortIngressTagHandling	1.3.6.1.4.1.164.4.1.9.3.1.6	INTEGER	read-write	This object indicates how is the Ingress VLAN Tag processed. It is mainly for use with Double Tagging.
INT radDot1qPortReplaceVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.7	INTEGER	read-write	This object indicates whether for each received tagged frame on this Bridge Port - VLAN Priority will be replaced by another Priority. no(2) = no repacement yes(3) = VLAN Priority will be replaced For Egate-100: When value is 'yes', the original Priority is replaced by the Default Priority.
INT radDot1qPortStacking	1.3.6.1.4.1.164.4.1.9.3.1.1	INTEGER	read-write	This object indicates the port stacking operation: unmodify (2) = Do not add Tag. tag (3) = Add Tag to Untagged Frames. stack (4) = Add Tag to all Frames.
INT radDot1qPortTagStripping	1.3.6.1.4.1.164.4.1.9.3.1.4	INTEGER	read-write	This object indicates whether remove a tag from the frame on this port, frame with double tag will remain with one tag and frame with one tag will remain untagged.
INT radDot1qPortVlanCnodeLevel1Agent	1.3.6.1.4.1.164.4.1.9.3.1.9	INTEGER	read-write	Specify if a Level 1 cNode agent is enabled or not for the bridge port.
radDot1qPortVlanEntry	1.3.6.1.4.1.164.4.1.9.3.1		not-accessible	Information controlling VLAN configuration for a port. This is indexed by dot1dBasePort.
U32 radDot1qPortVlanEthType	1.3.6.1.4.1.164.4.1.9.3.1.8	Unsigned32	read-write	This object indicates the Ethernet Type. For some devices, it is applicable only when radDot1qPortStacking = stack.
radDot1qPortVlanTable	1.3.6.1.4.1.164.4.1.9.3		not-accessible	A table containing control and status information for VLAN configuration per port.
radDXC10A	1.3.6.1.4.1.164.6.1.3.21
radDXC30	1.3.6.1.4.1.164.6.1.3.20
radDXC3000	1.3.6.1.4.1.164.6.1.3.24
radDXC30E	1.3.6.1.4.1.164.6.1.3.23
radDxc4	1.3.6.1.4.1.164.6.1.3.105
radDXC8R	1.3.6.1.4.1.164.6.1.3.22
radDXC8RNew	1.3.6.1.4.1.164.6.1.3.25
radEFcdIp	1.3.6.1.4.1.164.6.1.11.10
radEGate100	1.3.6.1.4.1.164.6.1.6.2
radEGate20	1.3.6.1.4.1.164.6.1.6.3
radEP4FL	1.3.6.1.4.1.164.6.1.9.5
radEP4T2FL	1.3.6.1.4.1.164.6.1.9.3
radEP4TAUI	1.3.6.1.4.1.164.6.1.9.2
radEP4TFL	1.3.6.1.4.1.164.6.1.9.4
radEP8T	1.3.6.1.4.1.164.6.1.9.1
radEPR4FL	1.3.6.1.4.1.164.6.1.9.11
radEPR4T2FL	1.3.6.1.4.1.164.6.1.9.9
radEPR4TAUI	1.3.6.1.4.1.164.6.1.9.8
radEPR4TFL	1.3.6.1.4.1.164.6.1.9.10
radEPR8T	1.3.6.1.4.1.164.6.1.9.7
radEthAccess	1.3.6.1.4.1.164.6.1.6
radETS4	1.3.6.1.4.1.164.6.1.7.7
radETS4fddiDAS	1.3.6.1.4.1.164.6.1.7.3
radETS4fddiSAS	1.3.6.1.4.1.164.6.1.7.4
radETX102	1.3.6.1.4.1.164.6.1.5.38
radETX102A	1.3.6.1.4.1.164.6.1.6.11
radETX102H	1.3.6.1.4.1.164.6.1.6.22
radETX105	1.3.6.1.4.1.164.6.1.5.44
radETX201	1.3.6.1.4.1.164.6.1.6.14
radETX201A	1.3.6.1.4.1.164.6.1.6.13
radETX202	1.3.6.1.4.1.164.6.1.5.43
radETX202A	1.3.6.1.4.1.164.6.1.6.12
radETX202AW	1.3.6.1.4.1.164.6.1.6.21
radETX202H	1.3.6.1.4.1.164.6.1.6.23
radETX205	1.3.6.1.4.1.164.6.1.5.45
radETX208	1.3.6.1.4.1.164.6.1.6.20
radETX510	1.3.6.1.4.1.164.6.1.6.1
radETX550	1.3.6.1.4.1.164.6.1.6.9
radFastWay100	1.3.6.1.4.1.164.6.1.4.28
radFcd155	1.3.6.1.4.1.164.6.1.3.90
radFcd155E	1.3.6.1.4.1.164.6.1.3.118
radFcd155ES	1.3.6.1.4.1.164.6.1.3.119
radFcd155EwAPS	1.3.6.1.4.1.164.6.1.3.130
radFcd155EwAPS2pdh	1.3.6.1.4.1.164.6.1.3.132
radFcd622	1.3.6.1.4.1.164.6.1.3.142
radFcdE1	1.3.6.1.4.1.164.6.1.3.31
radFcdE1A	1.3.6.1.4.1.164.6.1.3.37
radFcdE1I	1.3.6.1.4.1.164.6.1.3.32
radFcdE1L	1.3.6.1.4.1.164.6.1.3.29
radFcdE1LC	1.3.6.1.4.1.164.6.1.3.27
radFcdE1M	1.3.6.1.4.1.164.6.1.3.34
radFcdIP	1.3.6.1.4.1.164.6.1.3.35
radFcdIpD	1.3.6.1.4.1.164.6.1.11.11
radFcdIpL	1.3.6.1.4.1.164.6.1.11.13
radFcdIpM	1.3.6.1.4.1.164.6.1.11.12
radFcdIsdn	1.3.6.1.4.1.164.6.1.11.9
radFcdSTM	1.3.6.1.4.1.164.6.1.3.39
radFcdT1	1.3.6.1.4.1.164.6.1.3.30
radFcdT1A	1.3.6.1.4.1.164.6.1.3.36
radFcdT1L	1.3.6.1.4.1.164.6.1.3.28
radFcdT1LC	1.3.6.1.4.1.164.6.1.3.26
radFcdT1M	1.3.6.1.4.1.164.6.1.3.33
radFcdW	1.3.6.1.4.1.164.6.1.3.38
radFddi	1.3.6.1.4.1.164.2
radFdsl101	1.3.6.1.4.1.164.6.1.3.110
radFdsl201	1.3.6.1.4.1.164.6.1.3.111
radFDX100	1.3.6.1.4.1.164.6.1.2.1
radFEB4DAS	1.3.6.1.4.1.164.6.1.4.10
radFEB4FDX	1.3.6.1.4.1.164.6.1.4.22
radFEB4SAS	1.3.6.1.4.1.164.6.1.4.23
radFEC1	1.3.6.1.4.1.164.6.1.5.30
radFEC1UDP	1.3.6.1.4.1.164.6.1.5.33
radFEC2	1.3.6.1.4.1.164.6.1.5.32
radFEC2UDP	1.3.6.1.4.1.164.6.1.5.35
radFomiE3	1.3.6.1.4.1.164.6.1.3.72
radFomiT3	1.3.6.1.4.1.164.6.1.3.73
radFPS12	1.3.6.1.4.1.164.6.1.8.13
radFPS4	1.3.6.1.4.1.164.6.1.8.17
radFPS8	1.3.6.1.4.1.164.6.1.8.12
radFPS8c	1.3.6.1.4.1.164.6.1.8.16
radFRmon	1.3.6.1.4.1.164.6.1.3.80
radFTBDAS	1.3.6.1.4.1.164.6.1.4.26
radFTBSAS	1.3.6.1.4.1.164.6.1.4.27
radFTC1	1.3.6.1.4.1.164.6.1.5.10
radFTC1UDP	1.3.6.1.4.1.164.6.1.5.13
radFTC2	1.3.6.1.4.1.164.6.1.5.12
radFTC2UDP	1.3.6.1.4.1.164.6.1.5.15
radGen	1.3.6.1.4.1.164.6
radGmux2000	1.3.6.1.4.1.164.6.1.3.94
radGmux2004	1.3.6.1.4.1.164.6.1.3.149
radHcd4Sa	1.3.6.1.4.1.164.6.1.3.78
radHcdE1	1.3.6.1.4.1.164.6.1.3.52
radHcdE1Sa	1.3.6.1.4.1.164.6.1.3.51
radHtu2	1.3.6.1.4.1.164.6.1.3.43
radHtu2Sa	1.3.6.1.4.1.164.6.1.3.42
radHtuE1	1.3.6.1.4.1.164.6.1.3.41
radHtuE1Sa	1.3.6.1.4.1.164.6.1.3.40
radHtuE1SaV2	1.3.6.1.4.1.164.6.1.3.70
radHtuE1V2	1.3.6.1.4.1.164.6.1.3.71
radHtuT1	1.3.6.1.4.1.164.6.1.3.54
radHtuT1Sa	1.3.6.1.4.1.164.6.1.3.53
radImx2	1.3.6.1.4.1.164.6.1.3.62
radImx2T1E1	1.3.6.1.4.1.164.6.1.3.65
radImx4E1	1.3.6.1.4.1.164.6.1.3.64
radImx4T1	1.3.6.1.4.1.164.6.1.3.63
radImx64	1.3.6.1.4.1.164.6.1.3.60
radImx6L	1.3.6.1.4.1.164.6.1.3.61
radIMXI4	1.3.6.1.4.1.164.6.1.3.66
radIpMux1	1.3.6.1.4.1.164.6.1.3.82
radIpMux11	1.3.6.1.4.1.164.6.1.3.106
radIpMux116	1.3.6.1.4.1.164.6.1.3.115
radIpMux12	1.3.6.1.4.1.164.6.1.3.127
radIpMux14	1.3.6.1.4.1.164.6.1.3.107
radIpMux16	1.3.6.1.4.1.164.6.1.3.83
radIpMux1E	1.3.6.1.4.1.164.6.1.3.84
radIpMux216	1.3.6.1.4.1.164.6.1.3.147
radIpMux24	1.3.6.1.4.1.164.6.1.3.136
radIpMux2L	1.3.6.1.4.1.164.6.1.3.145
radIpMux4	1.3.6.1.4.1.164.6.1.3.81
radIpMux8	1.3.6.1.4.1.164.6.1.3.91
radKM2100	1.3.6.1.4.1.164.6.1.3.15
radKM2104	1.3.6.1.4.1.164.6.1.3.16
radLA104	1.3.6.1.4.1.164.6.1.13.3
radLA110	1.3.6.1.4.1.164.6.1.13.2
radLA130	1.3.6.1.4.1.164.6.1.13.4
radLA140	1.3.6.1.4.1.164.6.1.13.1
radLA210	1.3.6.1.4.1.164.6.1.13.5
radLA240	1.3.6.1.4.1.164.6.1.11.6
radLA240I	1.3.6.1.4.1.164.6.1.11.8
radLrs102	1.3.6.1.4.1.164.6.1.3.148
radLrs102unbal	1.3.6.1.4.1.164.6.1.3.150
radLrs12B	1.3.6.1.4.1.164.6.1.3.49
radLrs12F	1.3.6.1.4.1.164.6.1.3.48
radLrs16	1.3.6.1.4.1.164.6.1.3.151
radLrs22	1.3.6.1.4.1.164.6.1.3.143
radLrs52	1.3.6.1.4.1.164.6.1.3.50
radMBE1	1.3.6.1.4.1.164.6.1.4.5
radMBE1D	1.3.6.1.4.1.164.6.1.4.6
radMBE8	1.3.6.1.4.1.164.6.1.4.7
radMBE8D	1.3.6.1.4.1.164.6.1.4.8
radMBERAS	1.3.6.1.4.1.164.6.1.4.20
radMBERASa	1.3.6.1.4.1.164.6.1.4.21
radMdEntry	1.3.6.1.4.1.164.3.1.6.1.3.3.1		not-accessible	The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage
INT radMdFormat	1.3.6.1.4.1.164.3.1.6.1.3.3.1.2	INTEGER	read-create	The type (and thereby format) of the Maintenance Domain Name.
U32 radMdIndex	1.3.6.1.4.1.164.3.1.6.1.3.3.1.1	Unsigned32	not-accessible	The index to the maintenance domain table.
OCT radMdName	1.3.6.1.4.1.164.3.1.6.1.3.3.1.3	OCTET STRING	read-create	The Maintenance Domain name. The type/format of this object is determined by the value of the radMdNameType object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain.
ROW radMdRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.3.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
radMdTable	1.3.6.1.4.1.164.3.1.6.1.3.3		not-accessible	The MaintenanceDomain table. Each row in the table represents a different maintenance domain. A Maintenance domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance.
INT radMepCcInterval	1.3.6.1.4.1.164.3.1.6.1.3.1.1.19	INTEGER	read-create	Indicates the interval at which CCMs are sent by a MEP Valid only if radMepOamMode = initiate(4).
INT radMepCcStat	1.3.6.1.4.1.164.3.1.6.1.3.5.1.3	INTEGER	read-only	This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpectedMep -A MEP detects an Unexpected MEP condition when a CCM frame arrives with the correct MEG level, the correct MEG ID, but an unexpected MEP ID, which includes the MEP's own MEP ID. unexpectedMeLevel - A MEP detects an Unexpected MEG Level condition when a CCM frame arrives with incorrect MEG Level. Incorrect MEG Level is less than the MEP's own MEG level. unexpectedPeriod - A MEP detects an Unexpected Period condition when a CCM frame arrives with a correct MEG level. a correct MEG ID, a correct MEP ID, but with the Period field value different from the MEP's own CCM transmission period. rdi - A MEP detects RDI when it receives a CCM frame with the RDI field set.
INT radMepCcStatus	1.3.6.1.4.1.164.3.1.6.1.3.1.1.13	INTEGER	read-only	This object indicates the Continuity Check (CC) status.
radMepCcStatusEntry	1.3.6.1.4.1.164.3.1.6.1.3.5.1		not-accessible	An entry in the CC Status Table.
MAC radMepCcStatusMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.5.1.4	MacAddress	read-only	This object indicates the MAC Address in the CC Status message received.
U32 radMepCcStatusRemMepId	1.3.6.1.4.1.164.3.1.6.1.3.5.1.2	Unsigned32	read-create	This attribute indicates the Remote MEP ID from which the CC messages has arrived.
radMepCcStatusTable	1.3.6.1.4.1.164.3.1.6.1.3.5		not-accessible	This table contains a list of CC Status received by a specific MEP from different Remote MEPs.
INT radMepContinuityVerMode	1.3.6.1.4.1.164.3.1.6.1.3.1.1.8	INTEGER	read-create	This object determines the OAM behavior of the MEP: disabled - no CC is done cc_based - CC is done based on incoming messages lb_based - CC is done based on loopback messages.
U32 radMepDefaultPriority	1.3.6.1.4.1.164.3.1.6.1.3.1.1.12	Unsigned32	read-create	This object defines the priority of the OAM messages sent when no service is defined on EVC. If a service is defined, the OAM messages will get the highest service priority existing on the EVC.
radMepEntry	1.3.6.1.4.1.164.3.1.6.1.3.1.1		not-accessible	An entry in the table.
U32 radMepIdx	1.3.6.1.4.1.164.3.1.6.1.3.1.1.3	Unsigned32	not-accessible	This object indicates the ID of the MEP being accessed.
C32 radMepLbmOut	1.3.6.1.4.1.164.3.1.6.1.3.1.1.28	Counter32	read-only	Total number of Loopback Messages transmitted.
C32 radMepLbrIn	1.3.6.1.4.1.164.3.1.6.1.3.1.1.26	Counter32	read-only	Total number of valid, in-order Loopback Replies received.
C32 radMepLbrInOutOfOrder	1.3.6.1.4.1.164.3.1.6.1.3.1.1.27	Counter32	read-only	The total number of valid, out-of-order Loopback Replies received.
U32 radMepLocalMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.5	Unsigned32	read-create	This object indicates the local MEP ID.
INT radMepLtrEgress	1.3.6.1.4.1.164.3.1.6.1.3.4.1.8	INTEGER	read-only	The value returned in the Egress Action Field of the LTM. The value egrNoTlv(1) indicates that no Reply Egress TLV was returned in the LTM. 802.1ag clauses 12.14.7.5.3:o and 20.36.2.10
OCT radMepLtrEgressPortId	1.3.6.1.4.1.164.3.1.6.1.3.4.1.10	OCTET STRING	read-only	Egress Port ID. The format of this object is determined by the value of the radMepLtrEgressPortIdSubtype object. If the radMepLtrEgress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:r and 20.36.2.13
LLD radMepLtrEgressPortIdSubtype	1.3.6.1.4.1.164.3.1.6.1.3.4.1.9	LldpPortIdSubtype	read-only	The format of the egress Port ID. If the radMepLtrEgress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:q and 20.36.2.12
radMepLtrEntry	1.3.6.1.4.1.164.3.1.6.1.3.4.1		not-accessible	The LinktraceReply table entry.
INT radMepLtrIngress	1.3.6.1.4.1.164.3.1.6.1.3.4.1.5	INTEGER	read-only	The value returned in the Ingress Action Field of the LTM. ingNoTlv - no Reply Ingress TLV was returned in the LTM. ingOK - the target data frame would be passed through to the MAC Relay Entity. ingDown - the Bridge Port's MAC_Operational parameter is false. ingBlocked - the target data frame would not be forwarded if received on this port. ingVid - the ingress port is not in the members of the LTM's VID, and ingress filtering is enabled, so the target data frame would be filtered by the ingress filtering. 802.1ag clauses 12.14.7.5.3:k and 20.36.2.6
OCT radMepLtrIngressPortId	1.3.6.1.4.1.164.3.1.6.1.3.4.1.7	OCTET STRING	read-only	Ingress Port ID. This is an alpha-numeric string that contains a specific identifier for the port. The format of this object is determined by the value of the radMepLtrIngressPortIdSubtype object. If the radMepLtrIngress object contains the value ingNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:n and 20.36.2.9
LLD radMepLtrIngressPortIdSubtype	1.3.6.1.4.1.164.3.1.6.1.3.4.1.6	LldpPortIdSubtype	read-only	The format of the Ingress Port ID. If the radMepLtrIngress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:m and 20.36.2.8
MAC radMepLtrMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.4.1.3	MacAddress	read-only	The MAC address in the header of the returned LTR.
U32 radMepLtrReceiveOrder	1.3.6.1.4.1.164.3.1.6.1.3.4.1.1	Unsigned32	not-accessible	An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. radMepLtrReceiveOrder are assigned sequentially from 1, in the order that the Linktrace Initiator received the LTRs.
INT radMepLtrRelay	1.3.6.1.4.1.164.3.1.6.1.3.4.1.4	INTEGER	read-only	The value returned in the Relay Action field: rlyHit - the LTM reached an MP whose MAC address matches the target MAC address. rlyFdb - the Egress Port was determined by consulting the Filtering Database. rlyMpdb - the Egress Port was determined by consulting the MIP CCM Database. 802.1ag clauses 12.14.7.5.3:g and 20.36.2.5
radMepLtrTable	1.3.6.1.4.1.164.3.1.6.1.3.4		not-accessible	This table contains a list of Linktrace replies received by a specific MEP in response to a linktrace message.
U32 radMepLtrTtl	1.3.6.1.4.1.164.3.1.6.1.3.4.1.2	Unsigned32	read-only	TTL field value for a returned LTR.
INT radMepMaFormat	1.3.6.1.4.1.164.3.1.6.1.3.1.1.16	INTEGER	read-create	The type (and thereby format) of the Maintenance Association Name.
OCT radMepMaName	1.3.6.1.4.1.164.3.1.6.1.3.1.1.17	OCTET STRING	read-create	The Short Maintenance Association name.
U32 radMepMdId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.15	Unsigned32	read-create	The index of the Maintenance Domain in the radMdTable (radMdIndex).
U32 radMepMeLevel	1.3.6.1.4.1.164.3.1.6.1.3.1.1.9	Unsigned32	read-create	At any point in a network, ME Level is used to distinguish between OAM signals belonging to different nested MEs. Maintenance Entity Levels are defined as follows: 0,1,2 are assigned to customers 3,4 are assigned to providers 5,6,7 are assigned to operators.
INT radMepOamDestAddrType	1.3.6.1.4.1.164.3.1.6.1.3.1.1.10	INTEGER	read-create	This object determines if the OAM messages are sent to user defined unicast address, or to RAD proprietary multicast address.
MAC radMepOamDestMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.1.1.11	MacAddress	read-create	This object determines the MAC address that OAM packets are sent to.
INT radMepOamMode	1.3.6.1.4.1.164.3.1.6.1.3.1.1.7	INTEGER	read-create	This object determines the OAM mode of the MEP: disabled - no CC is initiated nor responded initiate - the device initiates and responds to CC react - the device does not initiate a CC, but responds to CC.
INT radMepOamProtocol	1.3.6.1.4.1.164.3.1.6.1.3.1.1.14	INTEGER	read-create	Determines whether to use proprietary OAM mechanism, or to use the standard (IEEE 802.1ag, ITU-T Y.1731).
U32 radMepRemoteMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.6	Unsigned32	read-create	This atribute is currently implemneted at radMepCcTable, that supports multicast.
U32 radMepRemoteMepIdx	1.3.6.1.4.1.164.3.1.6.1.3.5.1.1	Unsigned32	not-accessible	This is a running index for arriving CC messages (from different Remote MEPs) for a specific MEP ID.
ROW radMepRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.1.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table.
U32 radMepSpVlanId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.18	Unsigned32	read-create	The SP (Service Provider) VLAN used when sending an OAM message.
radMepTable	1.3.6.1.4.1.164.3.1.6.1.3.1		not-accessible	MEG End Point (MEP) configuration table associated with Maitenance Entity Group (MEG) End Point. MEP is a short name for an expanded ETH flow point that includes a compound ETH Segment flow termination function, which marks the end point of an ETH ME, and a compound ETH Diagnostic flow function.
INT radMepTransmitLbmDestIsMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.22	INTEGER	read-create	yes (3) indicates that MEPID of the target MEP is used for loopback transmission. no (2) indicates that unicast destination MAC address of the target MEP is used. 802.1ag clause 12.14.7.3.2:b.
MAC radMepTransmitLbmDestMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.1.1.20	MacAddress	read-create	The Target MAC Address Field to be transmitted in the Loopback Message: For unicast MAC Address this is the unicast destination MAC address. For multicast MAC Address, this variable is read-only. This address will be used if the value of radMepTransmitLbmDestIsMepId is no (2). 802.1ag clause 12.14.7.3.2:b.
U32 radMepTransmitLbmDestMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.21	Unsigned32	read-create	The MEPID of another MEP in the same MA to which the LBM is to be sent. This address will be used if the value of radMepTransmitLbmDestIsMepId is yes (3). 802.1ag clause 12.14.7.3.2:b.
I32 radMepTransmitLbmMassages	1.3.6.1.4.1.164.3.1.6.1.3.1.1.23	Integer32	read-create	The number of Loopback messages to be transmitted.
INT radMepTransmitLbmVlanDropEnable	1.3.6.1.4.1.164.3.1.6.1.3.1.1.25	INTEGER	read-create	Drop Enable bit to be used in the VLAN tag, if present, in the transmitted frame. 802.1ag clause 12.14.7.3.2:e
U32 radMepTransmitLbmVlanPriority	1.3.6.1.4.1.164.3.1.6.1.3.1.1.24	Unsigned32	read-create	The priority to be used in the VLAN tag, if present, in the transmitted frame. The default value is CCM priority. 802.1ag clause 12.14.7.3.2:e
INT radMepTransmitLtmActivationCmd	1.3.6.1.4.1.164.3.1.6.1.3.1.1.33	INTEGER	read-create	Activation command for starting Loop Trace. Set will be always to 'on' value. After operation was finished, Agent will turn the value to 'off'.
INT radMepTransmitLtmTargetIsMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.31	INTEGER	read-create	yes (3) indicates that MEPID of the target MEP is used for Linktrace transmission. no (2) indicates that unicast destination MAC address of the target MEP is used. 802.1ag clause 12.14.7.4.2:c.
MAC radMepTransmitLtmTargetMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.1.1.29	MacAddress	read-create	The Target MAC Address Field to be transmitted in the Link Trace Message: A unicast destination MAC address. This address will be used if the value of radMepTransmitLtmTargetIsMepId is no (2). 802.1ag clause 12.14.7.4.2:c.
U32 radMepTransmitLtmTargetMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.30	Unsigned32	read-create	The MEPID of another MEP in the same MA to which LTM is to be transmitted. This address will be used if the value of radMepTransmitLtmTargetIsMepId is yes (3). 802.1ag clause 12.14.7.4.2:c.
U32 radMepTransmitLtmTtl	1.3.6.1.4.1.164.3.1.6.1.3.1.1.32	Unsigned32	read-create	The LTM TTL field. Default value, if not specified, is 64. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 each Linktrace Responder that handles the LTM. The value received in the LTM is returned in the LTR. If 0 on input, the LTM is not transmitted to the next hop. 802.1ag clause 12.14.7.4.2:b and 21.8.4.
radMiniCVS	1.3.6.1.4.1.164.6.1.3.154
radMiricE1T1	1.3.6.1.4.1.164.6.1.5.49
radMiricE3T3	1.3.6.1.4.1.164.6.1.5.50
radMlAtmE1	1.3.6.1.4.1.164.6.1.12.2.10
radMlAtmT1	1.3.6.1.4.1.164.6.1.12.2.11
radMLBT	1.3.6.1.4.1.164.6.1.4.9
radMP104	1.3.6.1.4.1.164.6.1.3.86
radMP204	1.3.6.1.4.1.164.6.1.3.87
radMP2100	1.3.6.1.4.1.164.6.1.3.1
radMP2100B	1.3.6.1.4.1.164.6.1.3.3
radMP2100F	1.3.6.1.4.1.164.6.1.3.4
radMP2100H	1.3.6.1.4.1.164.6.1.3.5
radMP2100VoIP	1.3.6.1.4.1.164.6.1.3.134
radMP2104	1.3.6.1.4.1.164.6.1.3.2
radMP2104H	1.3.6.1.4.1.164.6.1.3.6
radMP2104VoIP	1.3.6.1.4.1.164.6.1.3.135
radMP2200B	1.3.6.1.4.1.164.6.1.3.7
radMP2200F	1.3.6.1.4.1.164.6.1.3.8
radMP4100	1.3.6.1.4.1.164.6.1.3.120
radMX30	1.3.6.1.4.1.164.6.1.3.11
radMX300	1.3.6.1.4.1.164.6.1.3.12
radMX3000	1.3.6.1.4.1.164.6.1.3.9
radMX3004	1.3.6.1.4.1.164.6.1.3.10
U32 radOamEvcIdx	1.3.6.1.4.1.164.3.1.6.1.3.1.1.2	Unsigned32	not-accessible	This object indicates the Index of the EVC (Ethernet Virtual Circuit) that the MEP is associated to.
U32 radOamIdx1	1.3.6.1.4.1.164.3.1.6.1.3.1.1.1	Unsigned32	not-accessible	This object may indicate the Bridge Index or Configuration index.
radOp1550	1.3.6.1.4.1.164.6.1.3.108
radOp16E1L	1.3.6.1.4.1.164.6.1.3.95
radOp16E1LS	1.3.6.1.4.1.164.6.1.3.96
radOp25	1.3.6.1.4.1.164.6.1.3.139
radOp34E1	1.3.6.1.4.1.164.6.1.3.123
radOp4E1	1.3.6.1.4.1.164.6.1.3.103
radOp4E1LNew	1.3.6.1.4.1.164.6.1.3.116
radOp4E1NG1	1.3.6.1.4.1.164.6.1.3.137
radOp4T1	1.3.6.1.4.1.164.6.1.3.104
radOp4T1LNew	1.3.6.1.4.1.164.6.1.3.117
radOp4T1NG1	1.3.6.1.4.1.164.6.1.3.138
radOpt4E1C	1.3.6.1.4.1.164.6.1.3.74
radOpt4T1C	1.3.6.1.4.1.164.6.1.3.75
radOptimux155	1.3.6.1.4.1.164.6.1.3.67
radOptimux155DS3	1.3.6.1.4.1.164.6.1.3.92
radOptimux4E1	1.3.6.1.4.1.164.6.1.3.55
radOptimux4E1L	1.3.6.1.4.1.164.6.1.3.69
radOptimux4E1Mar06	1.3.6.1.4.1.164.6.1.3.129
radOptimux4E1V3dot5	1.3.6.1.4.1.164.6.1.3.128
radOptimux4T1	1.3.6.1.4.1.164.6.1.3.56
radOptimux4T1L	1.3.6.1.4.1.164.6.1.3.68
radOptimux4T1Mar06	1.3.6.1.4.1.164.6.1.3.131
radOptimuxT3	1.3.6.1.4.1.164.6.1.3.79
radOptimuxT3L	1.3.6.1.4.1.164.6.1.3.93
radOptimuxXL16E1	1.3.6.1.4.1.164.6.1.3.59
radOptimuxXLE1	1.3.6.1.4.1.164.6.1.3.57
radOptimuxXLT1	1.3.6.1.4.1.164.6.1.3.58
radOpXL16E1	1.3.6.1.4.1.164.6.1.3.102
radOpXLE1	1.3.6.1.4.1.164.6.1.3.100
radOpXLT1	1.3.6.1.4.1.164.6.1.3.101
radPrbiE3	1.3.6.1.4.1.164.6.1.3.76
radPrbiT3	1.3.6.1.4.1.164.6.1.3.77
radPRBm20	1.3.6.1.4.1.164.6.1.3.97
radPRBm22	1.3.6.1.4.1.164.6.1.3.98
radRADring	1.3.6.1.4.1.164.6.1.1.1
radRBHE	1.3.6.1.4.1.164.6.1.7.1
radRBHEEvents	1.3.6.1.4.1.164.6.1.7.1.0			The events for RAD Stackable products.
radRBHT	1.3.6.1.4.1.164.6.1.7.2
radRBHTEvents	1.3.6.1.4.1.164.6.1.7.2.0			The events for RAD Stackable products.
radRIC155	1.3.6.1.4.1.164.6.1.5.36
radRIC155GE	1.3.6.1.4.1.164.6.1.5.39
radRIC622GE	1.3.6.1.4.1.164.6.1.5.47
radRICE1	1.3.6.1.4.1.164.6.1.5.37
radRici155GE	1.3.6.1.4.1.164.6.1.6.18
radRici16	1.3.6.1.4.1.164.6.1.6.10
radRici4E1	1.3.6.1.4.1.164.6.1.6.6
radRici4E1L	1.3.6.1.4.1.164.6.1.6.16
radRici4T1	1.3.6.1.4.1.164.6.1.6.7
radRici622GE	1.3.6.1.4.1.164.6.1.6.19
radRici8E1	1.3.6.1.4.1.164.6.1.6.4
radRici8E1L	1.3.6.1.4.1.164.6.1.6.17
radRici8T1	1.3.6.1.4.1.164.6.1.6.5
radRiciE3	1.3.6.1.4.1.164.6.1.5.41
radRiciSE	1.3.6.1.4.1.164.6.1.5.46
radRiciT1	1.3.6.1.4.1.164.6.1.5.42
radRiciT3	1.3.6.1.4.1.164.6.1.5.40
radRingMonitor	1.3.6.1.4.1.164.6.1.1.3
radRouter	1.3.6.1.4.1.164.11
radRRFTBDAS	1.3.6.1.4.1.164.6.1.4.24
radRRFTBSAS	1.3.6.1.4.1.164.6.1.4.25
radRRMLBT	1.3.6.1.4.1.164.6.1.4.15
radRRMLBTF	1.3.6.1.4.1.164.6.1.4.16
radRRTRE1D	1.3.6.1.4.1.164.6.1.4.17
radRRTRE8	1.3.6.1.4.1.164.6.1.4.13
radRRTRE8D	1.3.6.1.4.1.164.6.1.4.14
radRTEC	1.3.6.1.4.1.164.6.1.11.3
radRTED	1.3.6.1.4.1.164.6.1.11.1
radRTEM	1.3.6.1.4.1.164.6.1.11.2
radSAH16Eext	1.3.6.1.4.1.164.6.1.7.12
radSAH16Eint	1.3.6.1.4.1.164.6.1.7.10
radSAH16Text	1.3.6.1.4.1.164.6.1.7.13
radSAH16Tint	1.3.6.1.4.1.164.6.1.7.11
radSAHEMU	1.3.6.1.4.1.164.6.1.7.8
radSAHEMX	1.3.6.1.4.1.164.6.1.7.5
radSAHTM	1.3.6.1.4.1.164.6.1.7.6
radSEC1	1.3.6.1.4.1.164.6.1.5.20
radSEC1UDP	1.3.6.1.4.1.164.6.1.5.23
radSEC2	1.3.6.1.4.1.164.6.1.5.22
radSEC2UDP	1.3.6.1.4.1.164.6.1.5.25
radSPH	1.3.6.1.4.1.164.6.1.5.48
radSPS12	1.3.6.1.4.1.164.6.1.8.5
radSPS2	1.3.6.1.4.1.164.6.1.8.1
radSPS3	1.3.6.1.4.1.164.6.1.8.2
radSPS3S	1.3.6.1.4.1.164.6.1.8.11
radSPS3Sc2S	1.3.6.1.4.1.164.6.1.8.15
radSPS3ScSL	1.3.6.1.4.1.164.6.1.8.14
radSPS4	1.3.6.1.4.1.164.6.1.8.18
radSPS6	1.3.6.1.4.1.164.6.1.8.3
radSPS9	1.3.6.1.4.1.164.6.1.8.4
radStarSwitch	1.3.6.1.4.1.164.6.1.12.1
radStarSwitchATM155	1.3.6.1.4.1.164.6.1.12.1.3
radStarSwitchATM25	1.3.6.1.4.1.164.6.1.12.1.1
radStarSwitchATM25L	1.3.6.1.4.1.164.6.1.12.1.2
radSTC1	1.3.6.1.4.1.164.6.1.5.1
radSTC1UDP	1.3.6.1.4.1.164.6.1.5.4
radSTC2	1.3.6.1.4.1.164.6.1.5.3
radSTC2UDP	1.3.6.1.4.1.164.6.1.5.6
radStkHub	1.3.6.1.4.1.164.7
radSuperLan	1.3.6.1.4.1.164.6.1.11.7
radSysAtm	1.3.6.1.4.1.164.6.1.12
radSysAtmEvents	1.3.6.1.4.1.164.6.1.12.0			The events for RAD ATM products.
radSysBRG	1.3.6.1.4.1.164.6.1.4
radSysCnvrtr	1.3.6.1.4.1.164.6.1.5
radSysEth	1.3.6.1.4.1.164.6.1.9
radSysFddi	1.3.6.1.4.1.164.6.1.2
radSysLA	1.3.6.1.4.1.164.6.1.13
radSysPS	1.3.6.1.4.1.164.6.1.8
radSysPSEvents	1.3.6.1.4.1.164.6.1.8.0			The events for RAD Packet Switch (PS) products.
radSysRtr	1.3.6.1.4.1.164.6.1.11
radSysRtrEvents	1.3.6.1.4.1.164.6.1.11.0			The events for RAD Router products.
radSysStkHub	1.3.6.1.4.1.164.6.1.7
radSysTerminal	1.3.6.1.4.1.164.6.1.100
radSysTR	1.3.6.1.4.1.164.6.1.1
radSysWan	1.3.6.1.4.1.164.6.1.3
radSysWanEvents	1.3.6.1.4.1.164.6.1.3.0			The events for RAD Wan products.
radTinyRouter	1.3.6.1.4.1.164.6.1.11.5
radTMA	1.3.6.1.4.1.164.6.1.1.2
radTokenRing	1.3.6.1.4.1.164.1
radTransport	1.3.6.1.4.1.164.6.4
radTransportDomains	1.3.6.1.4.1.164.6.4.1
radTransportDomainSnmpEfmOam	1.3.6.1.4.1.164.6.4.1.1			The SNMP over EFM OAM transport domain. The corresponding transport address is of type RadTransportAddressEfmOam for EFM OAM addresses (port).
radTRE1	1.3.6.1.4.1.164.6.1.4.1
radTRE1D	1.3.6.1.4.1.164.6.1.4.2
radTRE8	1.3.6.1.4.1.164.6.1.4.3
radTRE8D	1.3.6.1.4.1.164.6.1.4.4
radTRERAS	1.3.6.1.4.1.164.6.1.4.18
radTRERASa	1.3.6.1.4.1.164.6.1.4.19
radTrimBrg10	1.3.6.1.4.1.164.6.1.4.11
radTrimBrg16	1.3.6.1.4.1.164.6.1.4.12
radUNT20E1	1.3.6.1.4.1.164.6.1.3.144
radUNT20Fcd	1.3.6.1.4.1.164.6.1.3.146
radUNT20Ric	1.3.6.1.4.1.164.6.1.6.15
radVmux110	1.3.6.1.4.1.164.6.1.3.88
radVmux120	1.3.6.1.4.1.164.6.1.3.112
radVmux210	1.3.6.1.4.1.164.6.1.3.122
radVmux2100	1.3.6.1.4.1.164.6.1.3.85
radVmux2200	1.3.6.1.4.1.164.6.1.3.113
radVmux312	1.3.6.1.4.1.164.6.1.3.124
radVmux314	1.3.6.1.4.1.164.6.1.3.141
radVmux320	1.3.6.1.4.1.164.6.1.3.133
radVmux400	1.3.6.1.4.1.164.6.1.3.114
radVmux404	1.3.6.1.4.1.164.6.1.3.125
radVmux405	1.3.6.1.4.1.164.6.1.3.152
radVmux420	1.3.6.1.4.1.164.6.1.3.126
radVmux425	1.3.6.1.4.1.164.6.1.3.153
radVOIP	1.3.6.1.4.1.164.6.1.3.13
radWan	1.3.6.1.4.1.164.3
radWebRanger	1.3.6.1.4.1.164.6.1.11.4
NTF remoteConnStatusTrap	1.3.6.1.4.1.164.6.1.3.0.14			This trap is sent upon a change in Remote connectivity of Bundle connection.
ripSapIfConfEntry	1.3.6.1.4.1.164.11.7.2.3.4.1		not-accessible	A Single Routing Domain in a single Subnet.
I32 ripSapIfConfIfIndex	1.3.6.1.4.1.164.11.7.2.3.4.1.1	Integer32	read-only	The interface ifIndex.
INT ripSapIfConfMode	1.3.6.1.4.1.164.11.7.2.3.4.1.2	INTEGER	read-create	The ifIndex RIP/SAP mode.
ROW ripSapIfConfStatus	1.3.6.1.4.1.164.11.7.2.3.4.1.3	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set ripSapIfConfStatus.id1 = active(1). For destroying a row, the NMS should set: ripSapIfConfStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
ripSapIfConfTable	1.3.6.1.4.1.164.11.7.2.3.4		not-accessible	A list of Interfaces which require separate configuration in RIP/SAP.
I32 rowInfoCounter	1.3.6.1.4.1.164.6.2.43.1.2	Integer32	read-only	The Number of rows in the table, indicated by rowInfoTableId.
rowInfoEntry	1.3.6.1.4.1.164.6.2.43.1		not-accessible	An entry in the table.
I32 rowInfoIndexNext	1.3.6.1.4.1.164.6.2.43.1.3	Integer32	read-only	The First Free Index of the table, indicated by rowInfoTableId.
I32 rowInfoMaxNoOfRows	1.3.6.1.4.1.164.6.2.43.1.4	Integer32	read-only	The maximum possible number of rows in the table, indicated by rowInfoTableId.
rowInfoTable	1.3.6.1.4.1.164.6.2.43		not-accessible	This table holds information of other tables.
OID rowInfoTableId	1.3.6.1.4.1.164.6.2.43.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of the Table, which its information is held by this table (rowInfoTable). Examples: Table Name rowInfoTableId --------------------------------------------------- atmTrafficDescrParamTable 1.3.6.1.2.1.37.1.5 atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .
rtrBridge	1.3.6.1.4.1.164.11.7
NTF sanityCheckTrap	1.3.6.1.4.1.164.3.3.0.1			This trap is sent after a data base download attempt. It returns the sanity result status and the configuration no.checked.
NTF sanityTrap	1.3.6.1.4.1.164.3.2.0.2			This trap is sent after a data base update. It returns the sanity result status and the configuration no. checked. If the result is of Flip DB Sanity Check, the configuration no. sent will be 0. If the result is of Variant Sanity Check, the configuration no. sent will be 100.
I32 schedParam	1.3.6.1.4.1.164.6.2.14.5.1.3	Integer32	read-create	A Parameter that might be used whenever the scheduled action takes place. For summer-time schedule - This variable represents the time offset (in minutes), meaning: the number of minutes that should be added for summer-time.
INT schedWeekInMonth	1.3.6.1.4.1.164.6.2.14.5.1.2	INTEGER	read-create	The week in month (schedMonth) during which the scheduled action should take place.
schedXEntry	1.3.6.1.4.1.164.6.2.14.5.1		not-accessible	An entry in the table.
schedXTable	1.3.6.1.4.1.164.6.2.14.5		not-accessible	An Augment to the Schedule table (schedTable in DISMAN-SCHEDULE-MIB; RFC-3231).
U32 schedYear	1.3.6.1.4.1.164.6.2.14.5.1.1	Unsigned32	read-create	The year during which the scheduled action should take place.
U32 serviceBwProfileId	1.3.6.1.4.1.164.6.3.6.1.5	Unsigned32	read-create	This variable holds the index of the Ingress BW profile assigned to that service.
serviceEntry	1.3.6.1.4.1.164.6.3.6.1		not-accessible	An entry in the Service Table.
U32 serviceIndex	1.3.6.1.4.1.164.6.3.6.1.2	Unsigned32	not-accessible	Defines the Service ID - according to the CoS.
STR serviceName	1.3.6.1.4.1.164.6.3.6.1.4	SnmpAdminString	read-create	This attribute defines the service name.
ROW serviceRowStatus	1.3.6.1.4.1.164.6.3.6.1.3	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
services	1.3.6.1.4.1.164.6.3
INT serviceStatDirection	1.3.6.1.4.1.164.6.3.8.1.1	INTEGER	not-accessible	The direction in wich the measurement is taken.
serviceStatEntry	1.3.6.1.4.1.164.6.3.8.1		not-accessible	An entry in the Service Statistics Table.
serviceStatTable	1.3.6.1.4.1.164.6.3.8		not-accessible	Service statistics table.
serviceTable	1.3.6.1.4.1.164.6.3.6		not-accessible	Table of services.
G32 srvDiscardGreenBytes	1.3.6.1.4.1.164.6.3.8.1.14	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Green.
G32 srvDiscardGreenBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.15	Gauge32	read-only	This attribute displays the number of times that the discardGreenBytes counter has overflowed.
G32 srvDiscardGreenPacket	1.3.6.1.4.1.164.6.3.8.1.6	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Green.
G32 srvDiscardGreenPacketOverflow	1.3.6.1.4.1.164.6.3.8.1.7	Gauge32	read-only	This attribute displays the number of times that the discardGreenPacket counter has overflowed.
G32 srvDiscardRedBytes	1.3.6.1.4.1.164.6.3.8.1.25	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Red.
G32 srvDiscardRedBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.26	Gauge32	read-only	This attribute displays the number of times that the discardRedBytes counter has overflowed.
G32 srvDiscardRedPackets	1.3.6.1.4.1.164.6.3.8.1.23	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Red.
G32 srvDiscardRedPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.24	Gauge32	read-only	This attribute displays the number of times that the discardRedPackets counter has overflowed.
G32 srvDiscardYellowBytes	1.3.6.1.4.1.164.6.3.8.1.21	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Yellow.
G32 srvDiscardYellowBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.22	Gauge32	read-only	This attribute displays the number of times that the discardYellowBytes counter has overflowed.
G32 srvDiscardYellowPackets	1.3.6.1.4.1.164.6.3.8.1.19	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Yellow.
G32 srvDiscardYellowPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.20	Gauge32	read-only	This attribute displays the number of times that the discardYellowPackets counter has overflowed.
G32 srvDiscardYellowRedBytes	1.3.6.1.4.1.164.6.3.8.1.16	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Yellow or Red.
G32 srvDiscardYellowRedBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.17	Gauge32	read-only	This attribute displays the number of times that the discardYellowRedBytes counter has overflowed.
G32 srvDiscardYellowRedPackets	1.3.6.1.4.1.164.6.3.8.1.8	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Yellow or Red.
G32 srvDiscardYellowRedPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.9	Gauge32	read-only	This attribute displays the number of times that the discardYellowRedPackets counter has overflowed.
G32 srvForwardGreenBytes	1.3.6.1.4.1.164.6.3.8.1.10	Gauge32	read-only	This attribute displays the counted number of forwarded bytes that where marked Green.
G32 srvForwardGreenBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.11	Gauge32	read-only	This attribute displays the number of times that the forwardGreenBytes counter has overflowed.
G32 srvForwardGreenPackets	1.3.6.1.4.1.164.6.3.8.1.2	Gauge32	read-only	This attribute displays the counted number of forwarded packets that where marked Green.
G32 srvForwardGreenPacktesOverflow	1.3.6.1.4.1.164.6.3.8.1.3	Gauge32	read-only	This attribute displays the number of times that the forwardGreenPackets counter has overflowed.
G32 srvForwardYellowBytes	1.3.6.1.4.1.164.6.3.8.1.12	Gauge32	read-only	This attribute displays the counted number of forwarded bytes that where marked Yellow.
G32 srvForwardYellowBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.13	Gauge32	read-only	This attribute displays the number of times that the forwardYellowBytes counter has overflowed.
G32 srvForwardYellowPackets	1.3.6.1.4.1.164.6.3.8.1.4	Gauge32	read-only	This attribute displays the counted number of forwarded packets that where marked Yellow.
G32 srvForwardYellowPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.5	Gauge32	read-only	This attribute displays the number of times that the forwardYellowPackets counter has overflowed.
INT srvResetStatsCmd	1.3.6.1.4.1.164.6.3.8.1.18	INTEGER	read-create	Reset statistic counters of the service.
statAgnGen	1.3.6.1.4.1.164.3.1.2.1
statisPrtGen	1.3.6.1.4.1.164.3.1.4.1.3
statMdlGen	1.3.6.1.4.1.164.3.1.3.1
statMdlMux	1.3.6.1.4.1.164.3.2.2.2
statPrtGen	1.3.6.1.4.1.164.3.1.4.1
statPrtMux	1.3.6.1.4.1.164.3.2.3.1
NTF statusChangedTrap	1.3.6.1.4.1.164.3.2.0.5			This trap is sent upon any change of the LEDs status.
NTF successfulLogin	1.3.6.1.4.1.164.6.1.0.24			This trap is sent when a user performed successful Login via Terminal/Telnet/Web. This trap is used when the device is located at End-User's premises while management is at Service Provider's premises.
swdlStatusEntry	1.3.6.1.4.1.164.6.2.12.11.1		not-accessible	An entry in table.
STR swdlStatusFileName	1.3.6.1.4.1.164.6.2.12.11.1.3	DisplayString	read-only	The name of the file.
I32 swdlStatusIdx	1.3.6.1.4.1.164.6.2.12.11.1.2	Integer32	read-only	The index of the status rows.
NTF swdlStatusResult	1.3.6.1.4.1.164.6.1.0.4			This notification is sent when Software Down Load is finished. The attached object indicates the File Name.
STR swdlStatusSlot	1.3.6.1.4.1.164.6.2.12.11.1.4	DisplayString	read-only	The slot of the updated (or attempted to be updated) object.
I32 swdlStatusStatus	1.3.6.1.4.1.164.6.2.12.11.1.6	Integer32	read-only	The status of the down load process. Value: Fail (2), OK (3), InProcess (4).
STR swdlStatusSubSystem	1.3.6.1.4.1.164.6.2.12.11.1.5	DisplayString	read-only	The subsystem that updated (or attempted to be updated).
swdlStatusTable	1.3.6.1.4.1.164.6.2.12.11		not-accessible	This parameters table is for software download status. It also includes data about the files down-loaded or attempted to be down-loaded.
STR swdlStatusTime	1.3.6.1.4.1.164.6.2.12.11.1.7	DisplayString	read-only	This MIB parameter indicates the time SW download was finished. The format shuld be YYYY-MM-DD, hh:mm:ss
I32 swdlStatusTypeIdx	1.3.6.1.4.1.164.6.2.12.11.1.1	Integer32	read-only	The index of the down-load type (e.g. external (1) or internal (2)).
NTF sysAlrStatusTrap	1.3.6.1.4.1.164.3.3.0.4			This trap is sent upon any change in the value of any of the variables.
sysBufferAlr	1.3.6.1.4.1.164.3.3.1.5
INT sysBufferAlrClearCmd	1.3.6.1.4.1.164.3.3.1.5.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2).
I32 sysBufferAlrCode	1.3.6.1.4.1.164.3.3.1.5.1.1.2	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and thir related descriptions will be known by the NMS (for display purpose) and will appear in the unit's user manual.
STR sysBufferAlrDate	1.3.6.1.4.1.164.3.3.1.5.1.1.6	DisplayString	read-only	The date when the alarm occured. The format will be according to sysSDateFormat.
sysBufferAlrEntry	1.3.6.1.4.1.164.3.3.1.5.1.1		not-accessible	An entry in table.
I32 sysBufferAlrIdx	1.3.6.1.4.1.164.3.3.1.5.1.1.1	Integer32	read-only	An index number of the current alarms.
STR sysBufferAlrInfo	1.3.6.1.4.1.164.3.3.1.5.1.1.9	SnmpAdminString	read-only	This parameter includes information about the alarm (additional to the Description).
I32 sysBufferAlrPort	1.3.6.1.4.1.164.3.3.1.5.1.1.5	Integer32	read-only	The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999.
INT sysBufferAlrSlot	1.3.6.1.4.1.164.3.3.1.5.1.1.4	INTEGER	read-only	The slot number this alarm refers to. When the alarm refers to a system function OR the DACS agent is a stand-alone unit, the value will be 'notApplicable(255)'. local/remote - for OP-4 device.
INT sysBufferAlrState	1.3.6.1.4.1.164.3.3.1.5.1.1.3	INTEGER	read-only	This object indicates the alarm type. minor/major/warning/critical - indicates appearance of the problem and the type. event - indicates occurence of an event. off - indicates disappearance of an alarm.
sysBufferAlrTable	1.3.6.1.4.1.164.3.3.1.5.1		not-accessible	List of current existing alarms (of all levels).
STR sysBufferAlrTime	1.3.6.1.4.1.164.3.3.1.5.1.1.7	DisplayString	read-only	The time when the alarm occured.
TIK sysBufferAlrUpTime	1.3.6.1.4.1.164.3.3.1.5.1.1.8	TimeTicks	read-only	The time when the alarm occured. This parameter holds the sysUpTime value when the alarm occured.
INT sysCAutoConfigEnable	1.3.6.1.4.1.164.3.3.1.6.2.1.5	INTEGER	read-write	This object enables user to enable/disable activating the Auto Configuration. When Auto Configuration is activated, the device learns its configuration Automatically from the Net it is connected to.
INT sysCBuPrimaryPort	1.3.6.1.4.1.164.3.3.1.6.2.1.7	INTEGER	read-write	This object enables the user to configure a Backup mechanism. If a backup mechanism exists, it is possible to configure the primary port. The traffic will flow via the primary port when the port functionality is OK. In Vmux-2100 device the backup mechanism is relevant for the Main Board only. The primary port can be the E1/T1/Serial port or the ETH port.
INT sysCBuRecMode	1.3.6.1.4.1.164.3.3.1.6.2.1.10	INTEGER	read-write	Recovery Mode. This object determines if after recovery of the Primary Link (used in Vmux) it will become on-line again or not: auto - automatic. In this case, the failed Link will become on-line again after recovery, automatically. manual - In this case, the failed Link will not become on-line again after recovery but user can manually flip to this Link.
I32 sysCClkCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. It can be also a combination of the configuration number and the Card/Port/Other System index.
U32 sysCClkRecoveredID	1.3.6.1.4.1.164.3.3.1.6.1.1.12	Unsigned32	read-write	This entry indicates the Recovered Clock ID. The value will be applicable only when sysCClkSrcMode is 'recovered'.
I32 sysCClkRevertiveTimeout	1.3.6.1.4.1.164.3.3.1.6.1.1.6	Integer32	read-write	The time in seconds in which the system will monitor the higher level clock source, before decision to revert to that clock. In case the time is zero, revertive mode will be disabled.
sysCClkSrcEntry	1.3.6.1.4.1.164.3.3.1.6.1.1		not-accessible	An entry in table.
INT sysCClkSrcIdx	1.3.6.1.4.1.164.3.3.1.6.1.1.2	INTEGER	read-only	An index in the table. There are only two entries in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
INT sysCClkSrcMode	1.3.6.1.4.1.164.3.3.1.6.1.1.3	INTEGER	read-write	This entry indicates the source the nodal timing is locked to. none - is an invalid option for Master clock. internal - is an invalid option for Fallback clock . station - is an invalid option for a stand-alone unit. lbt - loop-back timing ntr - Network Time Reference adaptive - clock locking is achieved by altering the clock according to the data load system - irrelevant when sysCClkCnfgIdx refers to System Clock. sSubSystem - SONET/SDH Sub System. recovered - clock recovery. notApplicable - for ML source of Kmux or ML Timing combinations when Master/Fallback clock are not applicable.
I32 sysCClkSrcPrt	1.3.6.1.4.1.164.3.3.1.6.1.1.4	Integer32	read-write	This entry is valid only when working in rxClk mode (for IPmux1000 this entry will be valid whe working in LBT mode). For ACE2002 in case of invalid entry the return value will be 0. For other products in case of invalid entry the return value will be 9999. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The SP ports will be numbered as follows: - SP port 1 : 1 - SP port 2 : 2 For external ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Kmux, the port will be according to : Slot*100+Ch. For ACE2002, LA140 and IPmux1000 (GMUX), the port will be ifIndex.
sysCClkSrcTable	1.3.6.1.4.1.164.3.3.1.6.1		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. For devices with more than one configuration: The write operation into the Table Objects is valid only for the TmpCnfg entry.
INT sysCClkSsmBased	1.3.6.1.4.1.164.3.3.1.6.1.1.10	INTEGER	read-write	This parameter indicates whether clock source will be selected based on receive clock quality, indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging). It is relevant only for sysCClkSrcIdx=master. When the value is Yes, sysCClkSrcMode must be notApplicable.
INT sysCClkSSubsystemSlot	1.3.6.1.4.1.164.3.3.1.6.1.1.11	INTEGER	read-write	This entry indicates the Slot from which the S Subsytem Source will be taken. The value will be applicable only when the sysCClkSrcMode is 'sSubsystem'.
INT sysCClkStationCableMode	1.3.6.1.4.1.164.3.3.1.6.1.1.8	INTEGER	read-write	This parameter indicates whether both Station clocks get their clock from the same source (Y Cable)or each one get its clock independently. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkStationFreq	1.3.6.1.4.1.164.3.3.1.6.1.1.5	INTEGER	read-write	This entry indicates the frequency of the station clock when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkStationIf	1.3.6.1.4.1.164.3.3.1.6.1.1.7	INTEGER	read-write	This entry indicates the electrical interface connected to the station clock, when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkStationOutState	1.3.6.1.4.1.164.3.3.1.6.1.1.9	INTEGER	read-write	This parameter indicates whether station clock can send its clock to another device. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCEnableLanOverTdm	1.3.6.1.4.1.164.3.3.1.6.2.1.8	INTEGER	read-write	This object enables/disables transferring traffic from the LAN port to the TDM port. It is possible to enable only part of the traffic on the TDM port for security reasons or in order to minimize the bandwidth .
sysChas	1.3.6.1.4.1.164.3.3.1.2.1
INT sysCIntTsAllocMode	1.3.6.1.4.1.164.3.3.1.6.2.1.6	INTEGER	read-write	This object enables user to select the mode of Internal TS Allocation. static - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). This number will be allocated to the ports, so that if number of connected TSs will grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports. dynamic- TS allocation is done dynamically according to the connected TSs. No future reservations are done. This mode may cause data disruption on other ports/slots if user will want to change the number of connected TSs for a Dynamic card port. staticOneToOne - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). In addition, the TSs themselves cannot be higher than this defined Maximum (e.g if Maximum TSs=5 user cannot selects TSs higher than 5). This mode ensures that if number of TSs grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports AND for the selected port itself. Default=static(2).
INT sysCIsdnFormat	1.3.6.1.4.1.164.3.3.1.6.2.1.3	INTEGER	read-write	ISDN format. This parameter controls the operation mode of the ISDN ports. te - ISDN timing is derived from the signal received from the equipment it is connected to. nt - timing of the transmit path is locked to the nodal timing source. notApplicable - for agents that do not support this feature.
INT sysCMatrixMode	1.3.6.1.4.1.164.3.3.1.6.2.1.2	INTEGER	read-write	Indicates the TS Matrix Mode: bidirectional - TS Assignment Matrix is symmetric. unidirectional - TS Assignment Matrix can be asymmetric. notApplicable - for agents that do not support this feature.
sysCnfgEntry	1.3.6.1.4.1.164.3.3.1.6.2.1		not-accessible	An entry in table.
I32 sysCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. For Gmux2000 the range limitation (1..255) was discarded since the Idx is computed as: x 1000 + 255.
sysCnfgTable	1.3.6.1.4.1.164.3.3.1.6.2		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
sysConfig	1.3.6.1.4.1.164.3.3.1.6
I32 sysCRdnBufferErrorsThreshold	1.3.6.1.4.1.164.3.3.1.6.3.1.17	Integer32	read-create	This parameter determines the number of Buffer undeflow/ overflow events occured in the time window that cause switching.
I32 sysCRdnBuffUnderrunTime	1.3.6.1.4.1.164.3.3.1.6.3.1.18	Integer32	read-create	This parameter determines how much time to wait before switching, after jitter buffer underrun. Switching occurs if no frame arrives within that time. For Ipmux time is counted in msec.
I32 sysCRdnCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
sysCRdnEntry	1.3.6.1.4.1.164.3.3.1.6.3.1		not-accessible	An entry in table.
I32 sysCRdnEventsTimeWindow	1.3.6.1.4.1.164.3.3.1.6.3.1.15	Integer32	read-create	This parameter determines the time window in which to count events to trigger protection switching. For Ipmux time is counted in seconds.
I32 sysCRdnFlipUponEvent	1.3.6.1.4.1.164.3.3.1.6.3.1.13	Integer32	read-create	This object allows user to define if Flip to the other port will be performed (or not), for certain possible events. Each event is represented by a bit. The value of the object is a sum of 2**n, according to the bits having '1' value. '1' - means that Flip should occur due to this event. Bit 0 (LSB) = SD (Signal Degraded). For IPmux: Bit 0 (LSB) = TDM Line LOS/LOF. Bit 1 = Sequence Number. Bit 2 = Jitter Buffer errors.
INT sysCRdnHwSwFlip	1.3.6.1.4.1.164.3.3.1.6.3.1.9	INTEGER	read-create	HW or SW decision for Redundancy Flip. This object is applicable only for sysCRdnMode=singleSlotProtection. HW - decision is by I/O card SW - decision is by CL SW.
I32 sysCRdnLosOrLofTime	1.3.6.1.4.1.164.3.3.1.6.3.1.14	Integer32	read-create	This parameter determines how much time to wait before switching, after LOF or LOS are detected on the TDM Line. For Ipmux time is counted in msec.
INT sysCRdnMode	1.3.6.1.4.1.164.3.3.1.6.3.1.6	INTEGER	read-create	Redundancy Mode. DXC supports: yCable(3), singleSlotProtection(6) and dualCableParallelTx(4) MP supports: yCable(3), dualCableParallelTx(4), onePlusOne(7) and oneToOne(8). (dualCableAIS and backup were planned for MP but were not implemented). backup - will be used when a port is backup of more than one port. IPmux: onePlusOne(7) and oneToOne(8) are used for Bundle redundancy.
STR sysCRdnName	1.3.6.1.4.1.164.3.3.1.6.3.1.22	SnmpAdminString	read-create	A textual name for the redundancy group.
INT sysCRdnOnline	1.3.6.1.4.1.164.3.3.1.6.3.1.11	INTEGER	read-only	Status - who is the Online (current) Redundancy Slot/Port. This object shows only the Online Slot/Port regarding the Redundancy. mdlSActivity or prtGenActiveStatus of the same Slot/Port may be Offline.
I32 sysCRdnPrimePort	1.3.6.1.4.1.164.3.3.1.6.3.1.3	Integer32	read-only	The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For an IP Bundle that is in an External Device (not in this MP), the value will be: 70,000 + ifIndex of Secondary Bundle. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level).
INT sysCRdnPrimePriority	1.3.6.1.4.1.164.3.3.1.6.3.1.19	INTEGER	read-create	The Primary port priority. In ETX2xx/2xxA: When selecting sysCRdnMode = manual (10), this parameter determines the forced active port: low - means that the secondary port is selected to be active high - means that the primary port is selected to be active.
INT sysCRdnPrimeSlot	1.3.6.1.4.1.164.3.3.1.6.3.1.2	INTEGER	read-only	The slot number of the Primary card of Redundancy. The Primary card should be the card that user wishes to be the online card (usually the more important one). For some Redundancy modes the importance of the redundant cards/ports is the same.
INT sysCRdnRecMode	1.3.6.1.4.1.164.3.3.1.6.3.1.7	INTEGER	read-create	Recovery Mode. This object determines if after recovery of the failed Primary card/port it will become on-line again or not: auto - automatic . In this case, the failed card/port will become on-line again after recovery, automatically. manual - In this case, the failed card/port will not become on-line again after recovery. But, user can manually flip to this card/port. nonRevertive - same as manual, but here user CANNOT manually flip to this card/port. It will become on-line again, only if the Secondary/Backup card/port will fail.
I32 sysCRdnRecTime	1.3.6.1.4.1.164.3.3.1.6.3.1.8	Integer32	read-create	Redundancy Recovery Time (sec). After switching to the current online card, the next switch can be performed only after a minimum time, indicated by this object. Valid Values: 0..300, 65535. 65535=NA. This object is applicable only when sysCRdnRecMode=auto.
ROW sysCRdnRowStatus	1.3.6.1.4.1.164.3.3.1.6.3.1.10	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table. The possible supported RowStatus values are active (1) and destroy (6). For Vmux-2100 the supported values are: active (1), createAndGo (4) and destroy (6).
I32 sysCRdnSecPort	1.3.6.1.4.1.164.3.3.1.6.3.1.5	Integer32	read-create	The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For an IP Bundle that is in an External Device (not in this MP), the value will be: 0. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level).
INT sysCRdnSecPriority	1.3.6.1.4.1.164.3.3.1.6.3.1.20	INTEGER	read-create	The Secondary port priority.
INT sysCRdnSecSlot	1.3.6.1.4.1.164.3.3.1.6.3.1.4	INTEGER	read-create	The slot number of the Secondary card of Redundancy matching the Primary slot.
I32 sysCRdnSequenceNumberThreshold	1.3.6.1.4.1.164.3.3.1.6.3.1.16	Integer32	read-create	This parameter determines the number of Sequence Number errors that should occur in the time window in order to cause switching.
INT sysCRdnSwitchingMode	1.3.6.1.4.1.164.3.3.1.6.3.1.12	INTEGER	read-create	This object defines which Self Healing Ring (SHR) SDH ring is used: Uni Directional or BiDirectional. The type of the ring is defined according to the direction of traffic flow under normal working conditions. In Bi Directional ring, the duplex traffic is on the same path and transverses the same set of nodes for both directions of transmission. In Uni Directional ring, the duplex traffic travels over opposite path (per direction) and all the node of the ring are involved. For Uni Directional SHR Protection Switching (Single Ended Switching) is controlled by one node of the SDH ring, and does not require a protocol. For Bi Directional SHR Protection Switching (Dual Ended switching) is controlled by some nodes of the ring and requires a protocol
sysCRdnTable	1.3.6.1.4.1.164.3.3.1.6.3		not-accessible	Configuration of all Redundant I/O cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that have no Redundancy, will not exist in this table.
U32 sysCRdnTxDownDurationUponFlip	1.3.6.1.4.1.164.3.3.1.6.3.1.23	Unsigned32	read-create	This object defines the duration (in seconds) the active port transmission is shut down after flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0 = no shut-down. This object is applicable only when sysCRdnMode = oneToOne(8) and mainly when each of the links of our device is connected to a different device.
U32 sysCRdnWTR	1.3.6.1.4.1.164.3.3.1.6.3.1.21	Unsigned32	read-create	Redundancy Wait to Restore (sec). Valid Values: 0..999, 65535. 65535=NA. When the value <> 65535, the value of sysCRdnRecTime must be 65535.
INT sysCRoutingOnEth	1.3.6.1.4.1.164.3.3.1.6.2.1.4	INTEGER	read-write	Mng Routing Protocol on the online CL Ethernet port, or on device Ethernet port dedicated for mangement.
I32 sysCSs7FisuSuppression	1.3.6.1.4.1.164.3.3.1.6.2.1.9	Integer32	read-write	SS7 Suppresion is used for SS7 Spoofing. The SS7 spoofing terminates the keep alive messages from the local VMUX without sending them over the network, thus improving the bandwidth utilization. FISU means Fill in Service Unit - Keep alive that is sent when no one is talking on the line. This object enables the configuration of the SS7 Keep Alive packet % that will be discarded. Legal Values: 0 - No Suppression, 10%, 20%, 30% .. 90% Example: For a value of 10, 1 keep alive packet will be discarded out of 10 keep alive packets that were supposed to be sent over the network.
sysCurrentAlr	1.3.6.1.4.1.164.3.3.1.4
sysDbase	1.3.6.1.4.1.164.3.3.1.7
I32 sysDbaseDownloadCnfgIdxCmd	1.3.6.1.4.1.164.3.3.1.7.2	Integer32	read-write	This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command, the DACS agent will initiate the Sanity-Check process. If successful, the actual transfer will be performed. If there will be errors, the user will have to perform the command again after errors correction. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg.
INT sysDbaseFlipActivation	1.3.6.1.4.1.164.3.3.1.7.4.1.3	INTEGER	read-write	This attribute indicates if the Dbase flip will be activated at the time specified for this configuration (enable) or not (disable). No more than one flip should be enabled for the same time.
sysDbaseFlipEntry	1.3.6.1.4.1.164.3.3.1.7.4.1		not-accessible	An entry in table.
I32 sysDbaseFlipIdx	1.3.6.1.4.1.164.3.3.1.7.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being the target Configuration.
sysDbaseFlipTable	1.3.6.1.4.1.164.3.3.1.7.4		not-accessible	Dbase Flip time and activation for every configuration.
STR sysDbaseFlipTime	1.3.6.1.4.1.164.3.3.1.7.4.1.2	DisplayString	read-write	This attribute indicates the time (HH:MM) when this data base will start being used by the Tmp config.
INT sysDbaseSanityCheckCmd	1.3.6.1.4.1.164.3.3.1.7.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion, the value will automatically change to off(2).
I32 sysDbaseUploadCnfgIdxCmd	1.3.6.1.4.1.164.3.3.1.7.3	Integer32	read-write	This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg.
sysDcl	1.3.6.1.4.1.164.3.3.1.2.2
INT sysDclActiveCl	1.3.6.1.4.1.164.3.3.1.2.2.1.1.3	INTEGER	read-write	Active desired DCL. When 'auto' is selected, the system automatically selects the active DCL.
I32 sysDclChFailThreshold	1.3.6.1.4.1.164.3.3.1.2.2.1.1.6	Integer32	read-write	This object indicates the number of failed channels that will trigger the redundancy procedure.
OCT sysDclChPriority	1.3.6.1.4.1.164.3.3.1.2.2.1.1.7	OCTET STRING	read-write	This object indicates the Priority for all the channels in the Main Access (Common Logic) card. Each channel is represented by 1 bit. The order of the bits in each byte is from Right to Left (LSB Bit to MSB) starting from BIT 0: 7 6 5 4 3 2 1 0 Channel no. 1 is represented by bit 0. Channel no. 2 is represented by bit 1. Channel no. n is represented by bit n-1. The value of the bit shows the priority. For bit value = 1, Priority = High. For bit value = 0, Priority = Low.
I32 sysDclCnfgIdx	1.3.6.1.4.1.164.3.3.1.2.2.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. For devices that work on line with NMS (no Temp configuration in NMS), Get and Set will be performed with index value of sysDclCnfgIdx = 1.
INT sysDclConfigDownloadSrc	1.3.6.1.4.1.164.3.3.1.2.2.1.1.8	INTEGER	read-write	In case of mismatch between the 2 CL card's configuration, the user can decide which card has the suitable configuration. The selected configuration will be downloaded from card A to card B if the value is dclA(2) or from card B to card A if the value is dclB(3). off(1) is used by part of the devices. In this case, after operation ends - value should be automatically set to off(1), which is the default state.
INT sysDclCopyDbCmd	1.3.6.1.4.1.164.3.3.1.2.2.3.1.2	INTEGER	read-write	When this command is sent to the agent, on(3), the Database specified (Db Idx), will be copied from the Offline Dcl to the Online Dcl. Afterwards the value of this object will automatically change to off(2).
sysDclCopyDbEntry	1.3.6.1.4.1.164.3.3.1.2.2.3.1		not-accessible	An entry in table.
I32 sysDclCopyDbIdx	1.3.6.1.4.1.164.3.3.1.2.2.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed.
sysDclCopyDbTable	1.3.6.1.4.1.164.3.3.1.2.2.3		not-accessible	This table enables to copy a cofiguration from the Offline Dcl to the Online Dcl.
sysDclEntry	1.3.6.1.4.1.164.3.3.1.2.2.1.1		not-accessible	An entry in table.
INT sysDclFlipCmd	1.3.6.1.4.1.164.3.3.1.2.2.4	INTEGER	read-write	When the 'flip(3)' command is received by Agent, it will flip (switch) between Offline Dcl and Online Dcl cards. Afterwards the value of this object will automatically change to off(2).
I32 sysDclFlipDelay	1.3.6.1.4.1.164.3.3.1.2.2.1.1.4	Integer32	read-write	If one DCL flip occurred and a second one should be performed, the time from the previous flip is checked. If the time is shorter than the delay specified here, the system should delay the flip operation until time reaches the specified delay. For DXC the values are 1 minute to 4 minutes (1..4). For Optimux-155-1 and Optimux-155-3 the values are: 0...60 Sec. 0 means No Delay.
INT sysDclFlipUponStnClk	1.3.6.1.4.1.164.3.3.1.2.2.1.1.5	INTEGER	read-write	This object allows user to decide (yes/no) if Agent should Flip from one DCL card to another, when there is Station Clock Fail in the Online DCL card.
INT sysDclOnline	1.3.6.1.4.1.164.3.3.1.2.2.2	INTEGER	read-only	The active Dcl card of the agent.
INT sysDclRedundancy	1.3.6.1.4.1.164.3.3.1.2.2.1.1.2	INTEGER	read-write	DCL redundancy desired state.
BIT sysDclRedundancyStatus	1.3.6.1.4.1.164.3.3.1.2.2.1.1.10	Bits	read-only	Bit map representing current Redundancy Status. bit 0 - Indicates mismatch between the 2 CL cards' Configuration bit 1 - Indicates mismatch between the 2 CL cards' Software. bit 2 - Indicates CL card A Absence. bit 3 - Indicates CL card B Absence. bit 4 - Indicates Loss of Communication between the 2 CL cards. bit 5 - Indicates mismatch between the 2 CL cards' Hardware. bit 6 - Indicates Configuraton update is in process. bit 7 - Indicates Software update is in process.
INT sysDclSwDownloadSrc	1.3.6.1.4.1.164.3.3.1.2.2.1.1.9	INTEGER	read-write	In case of mismatch between the 2 CL card's software, the user can decide which card has the suitable SW. The selected SW will be downloaded from card A to card B if the value is dclA(2) or from card B to card A if the value is dclB(3). off(1) is used by part of the devices. In this case, after operation ends - value should be automatically set to off(1), which is the default state.
sysDclTable	1.3.6.1.4.1.164.3.3.1.2.2.1		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
sysHub	1.3.6.1.4.1.164.3.3.1.2
NTF sysRedundancyActiveCardTrap	1.3.6.1.4.1.164.3.3.0.8			The trap is sent upon change of Active Main/CL Card.
NTF sysRedundancyActivePortTrap	1.3.6.1.4.1.164.3.3.0.9			The trap is sent upon change of Active Port of Redundancy Group.
NTF sysRedundancyStatusTrap	1.3.6.1.4.1.164.3.3.0.7			The trap is sent upon change in Redundancy Status.
sysSa	1.3.6.1.4.1.164.3.3.1.1
INT sysSaBuActivePort	1.3.6.1.4.1.164.3.3.1.1.6	INTEGER	read-only	This object shows through which port the traffic is flowing (the current Active Port) when the Backup mechanism exists. When No Backup exists in the device, the value should be: notApplicable(1).
I32 sysSActiveCnfg	1.3.6.1.4.1.164.3.3.1.3.4	Integer32	read-only	This object specifies the configuration number, that is currently active and running.
STR sysSaHwVersion	1.3.6.1.4.1.164.3.3.1.1.3	DisplayString	read-only	This object indicates the Hardware version of the system.
I32 sysSAlarmCounter	1.3.6.1.4.1.164.3.3.1.4.1.1.7	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
INT sysSAlarmInvert	1.3.6.1.4.1.164.3.3.1.4.1.1.5	INTEGER	read-only	Alarm Invert is : on/off.
INT sysSAlarmMask	1.3.6.1.4.1.164.3.3.1.4.1.1.4	INTEGER	read-only	Alarm Mask is : on/off.
INT sysSAlarmOnOff	1.3.6.1.4.1.164.3.3.1.4.1.1.6	INTEGER	read-only	Alarm state is : on/off.
I32 sysSAlrAttrIndication	1.3.6.1.4.1.164.3.3.1.3.23	Integer32	read-only	This object indicates the status of the Alarm Attributes for the whole device. It is a sum of 2**(Bit-1). A Bit will be '1', when any alarm in the device is Filtered/Masked/Inverted (respectively). The Bit assignment is: Bit 1: Filter (LSB) Bit 2: Mask Bit 3: Invert (MSB). Examples: - Alarms are filtered and masked but not inverted: value=3 - Alarm is Inverted (not filtered or masked): value=4 - Alarm is masked (not inverted or filtered): value=2
INT sysSAlrClearAllCmd	1.3.6.1.4.1.164.3.3.1.4.3	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on all levels alarms . Upon completion, the value will automatically change to off(2).
INT sysSAlrClearCmd	1.3.6.1.4.1.164.3.3.1.4.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the system level alarms . Upon completion, the value will automatically change to off(2).
I32 sysSAlrCode	1.3.6.1.4.1.164.3.3.1.4.1.1.2	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
INT sysSAlrDataUpdateCmd	1.3.6.1.4.1.164.3.3.1.4.6	INTEGER	read-write	on(3) - will cause Update of the Alarms Severity, Attributes and Report tables. off(2) - Upon completion, the value will automatically change to off(2).
sysSAlrEntry	1.3.6.1.4.1.164.3.3.1.4.1.1		not-accessible	An entry in table.
I32 sysSAlrIdx	1.3.6.1.4.1.164.3.3.1.4.1.1.1	Integer32	read-only	An index number of the current system alarms.
OCT sysSAlrMask	1.3.6.1.4.1.164.3.3.1.4.5	OCTET STRING	read-write	This object is a mask that indicates which system level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the system level will be 0. This object is applicable only when sysSAlrMaskAll=off (otherwise all system alarms are masked). Example: When Alarms having the codes 6 and 11 are masked, the value of this object will be 840 (hex).
INT sysSAlrMaskAll	1.3.6.1.4.1.164.3.3.1.4.4	INTEGER	read-write	on(3) - will cause masking of all the system level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all system level alarms except those masked via the sysSAlrMask.
INT sysSAlrState	1.3.6.1.4.1.164.3.3.1.4.1.1.3	INTEGER	read-only	This object indicates the alarm Severity.
INT sysSAlrStatus	1.3.6.1.4.1.164.3.3.1.3.8	INTEGER	read-only	Indicates the current alarm state only for system level. This object will be : - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT sysSAlrStatusAll	1.3.6.1.4.1.164.3.3.1.3.9	INTEGER	read-only	Indicates the current alarm state including all levels: system, card, port. - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
sysSAlrTable	1.3.6.1.4.1.164.3.3.1.4.1		not-accessible	List of system level current existing alarms .
I32 sysSaPorts	1.3.6.1.4.1.164.3.3.1.1.4	Integer32	read-only	This object indicates the ports that are present in the system. Each possible port is represented by a bit. The value of this object is a sum of 2**n, n=number of bits. '1' - means that the port exists '0' - means that the port does not exist For detailed bit assignment, see product's spec. Bit 0 = LSB When this object is not relevant, the value will be 0. In some cases, this object may represent ports configuration of the system AND its far-end unit.
I32 sysSaReadSwch	1.3.6.1.4.1.164.3.3.1.1.5	Integer32	read-write	This object indicates wether the configuration will be read from the DIP switches on the SA (stand alone) unit. Each switch is represented by a bit. If the bit is 1: the configuration will be read from the HW switch position. If the bit is 0: the configuration will be read from the SW user configuration. The DIP switches are different in each of the RAD devices. In the Tiny Router (starting from the LSB) the following switches exist: Bit 0: WAN Loop Bit 1: LAN Full Duplex (When LAN AUI connector, it is SQE) Bit 2: PPP (When WAN 4 Wire connector, it is LONG) Bit 3: IP Learn
I32 sysSaSwchStatus	1.3.6.1.4.1.164.3.3.1.1.1	Integer32	read-only	This object indicates the status of the switches on the SA unit. Each switch is represented by a bit. The status is a sum of 2n, according to the bits. For SMODs products see modem's specification. For DXC product see the following: There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (21 + 2**0). When the status of the switches is unknown, the value of this object will be 255.
STR sysSaSwRevision	1.3.6.1.4.1.164.3.3.1.1.2	DisplayString	read-only	This object indicates the Software revision of the system.
I32 sysSBusCapturePort	1.3.6.1.4.1.164.3.3.1.3.21.1.3	Integer32	read-only	The Port that Captured the sysSBusPortIdx. - if sysSBusStatus=free, the value will be 'none'=0 - else, if sysSBusStatus=fixed, the value will be: sysSBusPortIdx - else, the value will be according to the port index that captured this Bus Port (according to DXC port index convention): - xx1, xx3, xx11, xx13, xx31, xx33, xx2..xx56(even numbers) - xx = (IO slot number+10)
sysSBusEntry	1.3.6.1.4.1.164.3.3.1.3.21.1		not-accessible	An entry in table.
I32 sysSBusPortIdx	1.3.6.1.4.1.164.3.3.1.3.21.1.1	Integer32	read-only	The DXC BUS port number: - first two digits will be: (IO slot number+10) - last one/two digits will be the Bus port number, in odd numbers: port1 = 1 port2 = 3 Example: port2 of IO slot 11 will be: 213.
INT sysSBusStatus	1.3.6.1.4.1.164.3.3.1.3.21.1.2	INTEGER	read-only	The Status of sysSBusPortIdx. free - not used physical - captured by the port of the card physically installed virtual - captured virtually by another port. Example: DIM port (by Destination) or by Transparent T3/E3 port.
sysSBusTable	1.3.6.1.4.1.164.3.3.1.3.21		not-accessible	This table includes data and status about the internal DXC BUS.
I32 sysSBusUtilization	1.3.6.1.4.1.164.3.3.1.3.21.1.4	Integer32	read-only	Utilization of sysSBusPortIdx resources, in percent [%].
INT sysSClkSrc	1.3.6.1.4.1.164.3.3.1.3.7	INTEGER	read-only	This entry indicates the source of the system clock.
STR sysSDateCmd	1.3.6.1.4.1.164.3.3.1.3.2	DisplayString	read-write	This object indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the sysSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent. * For KM-2100 V1 and FCD-T1/E1 - the string should contain '/' signs between day, month and year. Example: 12/08/1998. * For DXC and rest of the products - the string should contain '-' signs between day, month and year. Example: 12-08-1998. The day value will be in the range: 1..31. The month value will be in the range: 1..12. The year value will be in the range: 1996..2050 for products supporting the '-' format.
INT sysSDateFormat	1.3.6.1.4.1.164.3.3.1.3.1	INTEGER	read-write	This object indicates the date and time format used for the sysSDateAndTimeCmd and for the alarm buffer report.
INT sysSEditBy	1.3.6.1.4.1.164.3.3.1.3.6	INTEGER	read-only	This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after a load operation.
I32 sysSEditCnfg	1.3.6.1.4.1.164.3.3.1.3.5	Integer32	read-only	This object indicates the unique configuration number that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process.
STR sysSErrDescription	1.3.6.1.4.1.164.3.3.1.3.13.1.3	DisplayString	read-only	This object is a full text description of the sanity check error including error code, IO slot and port numbers related to the code .
I32 sysSErrIdx	1.3.6.1.4.1.164.3.3.1.3.13.1.2	Integer32	read-only	Unique index number to identify an entry in the error or warning list . The maximum value cannot exceed the value of 'sysSNoOfSanityCheckErr' (actually, the sum of the Errors list max. index and the Warning list max. index should equal the value of'sysSNoOfSanityCheckErr').
sysSErrListEntry	1.3.6.1.4.1.164.3.3.1.3.13.1		not-accessible	An entry in table.
sysSErrListTable	1.3.6.1.4.1.164.3.3.1.3.13		not-accessible	A table.
INT sysSErrType	1.3.6.1.4.1.164.3.3.1.3.13.1.1	INTEGER	read-only	The errors are recorded in the agent, in two separate lists, according to their type: error or warning.
INT sysSInvertedAlr	1.3.6.1.4.1.164.3.3.1.3.17	INTEGER	read-only	Indicates if there is any Inverted alarm at any level of the system (sys, card, port). notApplicable - for agents that do not support this object.
I32 sysSMaxNoOfCnfg	1.3.6.1.4.1.164.3.3.1.3.14	Integer32	read-only	Maximum number of configurations that can be defined and stored in the DACS agent. If the DACS agent has a large capacity, the maximum will be limited to 254.
I32 sysSNoOfSanityCheckErr	1.3.6.1.4.1.164.3.3.1.3.12	Integer32	read-only	This object indicates the number of errors/warnings discovered by the last Sanity Check process.
sysSRdnCmdEntry	1.3.6.1.4.1.164.3.3.1.3.22.1		not-accessible	An entry in table.
sysSRdnCmdTable	1.3.6.1.4.1.164.3.3.1.3.22		not-accessible	This table includes commands used for IO Redundancy.
INT sysSRdnEnforcedChannel	1.3.6.1.4.1.164.3.3.1.3.22.1.1	INTEGER	read-write	This is a command to override all switching considerations and enforce use of primary/ secondary connection only. noEnforcement - cancels the state of override and goes back to usual switching considerations. Default = noEnforcement(2).
STR sysSRdnFlipCause	1.3.6.1.4.1.164.3.3.1.3.18.1.4	DisplayString	read-only	The last cause that caused the Flip from the Slot (Port) of sysSRdnSlot, sysSRdnPort.
OID sysSRdnFlipCmd	1.3.6.1.4.1.164.3.3.1.3.20	OBJECT IDENTIFIER	read-write	This object enables the user to send a command to the Agent, to Flip from a current Online IO card to its Redundant card. The value sent will be an Object Identifier of an entry in the sysCRdnTable. This entry defines the Redundant couple of Slots on which the Flip is applied. Setting this object, will cause the Agent to Flip from current Online card to its Redundant card. This manual flip command is applicable only for entries having Redundancy Mode=Y Cable. For Vmux: This command will cause flipping from Secondary or Third Link to the Primary Link. If the active link is the primary link, the agent will flip to the secondary link. The value sent will be the Object Identifier of the following Table: agnCBuMlTable. Agent will send the value 0 for Get.
STR sysSRdnFlipDate	1.3.6.1.4.1.164.3.3.1.3.18.1.5	DisplayString	read-only	Flip event Date. The format will be the one selected by user for sysSDateFormat.
sysSRdnFlipEntry	1.3.6.1.4.1.164.3.3.1.3.18.1		not-accessible	An entry in table.
I32 sysSRdnFlipIdx	1.3.6.1.4.1.164.3.3.1.3.18.1.1	Integer32	read-only	Unique index number to identify an entry in the Redundancy Flip list.
I32 sysSRdnFlipPort	1.3.6.1.4.1.164.3.3.1.3.18.1.3	Integer32	read-only	The port number from which Flip was performed. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 100=notApplicable (when Redundancy is at card level).
INT sysSRdnFlipSlot	1.3.6.1.4.1.164.3.3.1.3.18.1.2	INTEGER	read-only	The slot number from which Flip was performed.
sysSRdnFlipTable	1.3.6.1.4.1.164.3.3.1.3.18		not-accessible	This table includes all the Flip events due to I/O Redundancy since last Clear command of this table.
INT sysSRdnFlipTableClearCmd	1.3.6.1.4.1.164.3.3.1.3.19	INTEGER	read-write	This command, when Set to 'on', clears the Redundancy Flip table (sysSRdnFlipTable). After clear is performed, the agent will turn the value to 'off' automatically.
STR sysSRdnFlipTime	1.3.6.1.4.1.164.3.3.1.3.18.1.6	DisplayString	read-only	Flip event Time. The format will be hh:mm:ss.
INT sysSRdnLockFlip	1.3.6.1.4.1.164.3.3.1.3.22.1.2	INTEGER	read-write	This is a command to lock the Redundancy flip for this redundancy couple. Default = off(2).
INT sysSRdnManualFlip	1.3.6.1.4.1.164.3.3.1.3.22.1.3	INTEGER	read-write	This is a command to move to manual Redundancy flip mode for this redundancy couple. Default = off(2).
INT sysSRelayState	1.3.6.1.4.1.164.3.3.1.3.16	INTEGER	read-only	Indicates the current state of the alarm relay. notApplicable - for agents that do not support this object.
INT sysSSanityCheckStatus	1.3.6.1.4.1.164.3.3.1.3.11	INTEGER	read-only	Upon completion of the Sanity Check process on the TmpCnfg this object will be set to: - fail(2): when there is at least one error (which is not just a warning) encountered otherwise, - warning(3): when there are only warnings otherwise, - ok(4). The value should be unknown(1), if the TmpCnfg was changed after the last Sanity check.
I32 sysSSelfTestResult	1.3.6.1.4.1.164.3.3.1.3.15	Integer32	read-only	The test is performed by the active Common Logic card. The result will be a sum of 2**n according to the following bit convention: For DXC: bit 0 Database 1 Checksum Error (LSB) bit 1 Database 2 Checksum Error bit 2 I/O Expander Error bit 3 Counter Error bit 4 Matrix DPR Error bit 5 PS-A 5 Volt Error bit 6 PS-A 12 Volt Error bit 7 PS-B 5 Volt Error bit 8 PS-B 12 Volt Error bit 9 EPROM Failure For FCD: bit 0 I/O Expander Error (LSB) bit 1 Counter Error bit 2 EPROM Failure bit 3 Illegal Sys Config bit 4 SFIFO bit 5 EPIC Failure (ISDN) bit 6 XL Flash Fail -- for MSDSL interface bit 7 XL MITEL Fail -- for MSDSL interface bit 8 XL Framer Fail -- for MSDSL interface bit 9 XL DSP Fail -- for MSDSL interface For LRS52 - refer to product's spec When a bit is ('1'), the error exists. When NO ERROR is encountered, this object's value will be 0.
sysStatus	1.3.6.1.4.1.164.3.3.1.3
NTF sysStatusChangedTrap	1.3.6.1.4.1.164.3.3.0.5			This trap is sent when Leds status is changed.
INT sysSTestStatus	1.3.6.1.4.1.164.3.3.1.3.10	INTEGER	read-only	Indicates the current test status (for all levels: system, card, port). This attribute will be set to: - on(3): when there is at least one test in progress on the system/card/port otherwise the value will be off(2).
STR sysSTimeCmd	1.3.6.1.4.1.164.3.3.1.3.3	DisplayString	read-write	This object indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent. The string should contain ':' signs between hour, minute and second. Example: 11:05:58.
INT systemClearTablesCmd	1.3.6.1.4.1.164.6.2.17	INTEGER	read-write	tempCnfgTables - Set RowStatus = destroy for all entries of some tables having RowStatus object, for temporary configuration only! (255). For the relevant tables, see product's specification. This object should be used by WAN product applications before performing the Update operation, in order to clear old entries of these tables. For MP-104/204 the entries will be destroyed for cnfg=1. off - agent will automatically change to this value, after performing the command.
systemDacsMux	1.3.6.1.4.1.164.3.3.1
STR systemDate	1.3.6.1.4.1.164.6.2.14.1	DisplayString	read-write	System date.
IP systemDefaultGateway	1.3.6.1.4.1.164.6.2.24	IpAddress	read-write	Default Gateway's IP Address.
systemInterface	1.3.6.1.4.1.164.6.2.35
systemModule	1.3.6.1.4.1.164.6.2.32
systemNtp	1.3.6.1.4.1.164.6.2.14.4
INT systemNtpCmd	1.3.6.1.4.1.164.6.2.14.4.6	INTEGER	read-write	This variable represents NTP possible commands. After the Agent accepts a command, it will automatically change the value to off(2).
I32 systemNtpGmt	1.3.6.1.4.1.164.6.2.14.4.2	Integer32	read-write	This variable represents the NTP GMT (Greenwich Mean Time), Possible values range is -12..12. For new devices/versions this variable will be in minutes.
INT systemNtpMode	1.3.6.1.4.1.164.6.2.14.4.1	INTEGER	read-write	This variable represents the NTP Mode.
IP systemNtpServerAddress	1.3.6.1.4.1.164.6.2.14.4.4	InetAddress	read-write	This variable represents the NTP Server Address.
IPt systemNtpServerAddressType	1.3.6.1.4.1.164.6.2.14.4.3	InetAddressType	read-write	This variable represents the NTP Server Address Type.
U32 systemNtpUpdateInterval	1.3.6.1.4.1.164.6.2.14.4.5	Unsigned32	read-write	This variable represents the NTP Update Interval, measured in seconds.
systemOam	1.3.6.1.4.1.164.6.2.36
I32 systemOamCnfgIdx	1.3.6.1.4.1.164.6.2.36.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
INT systemOamDescrCCDirection	1.3.6.1.4.1.164.6.2.36.2.1.4	INTEGER	read-create	OAM Continuity Check function mode. both(2) - Agent sends OAM CC cells and checks received OAM CC cells. none(3) - Agent does not send and does not check received OAM CC cells. source(4)- Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells.
systemOamDescrEntry	1.3.6.1.4.1.164.6.2.36.2.1		not-accessible	An entry in the OAM table.
I32 systemOamDescrIdx	1.3.6.1.4.1.164.6.2.36.2.1.1	Integer32	not-accessible	The OAM Descriptor Index.
OCT systemOamDescrLoopbackDestAddr	1.3.6.1.4.1.164.6.2.36.2.1.6	OCTET STRING	read-create	Loopback Destination Address.
INT systemOamDescrLoopbackOperation	1.3.6.1.4.1.164.6.2.36.2.1.5	INTEGER	read-create	The OAM Loopback function mode. off(2) - Stop sending loopback OAM cells. on(3) - Start loopback OAM cells.
INT systemOamDescrMode	1.3.6.1.4.1.164.6.2.36.2.1.3	INTEGER	read-create	The OAM Mode of the Descriptor.
ROW systemOamDescrRowStatus	1.3.6.1.4.1.164.6.2.36.2.1.2	RowStatus	read-create	Enables the user to create/delete entries in this table.
systemOamDescrTable	1.3.6.1.4.1.164.6.2.36.2		not-accessible	The OAM Descriptors Configuration Table.
G32 systemOamDescrXcCounter	1.3.6.1.4.1.164.6.2.36.2.1.7	Gauge32	read-only	The number of connections that use this OAM Descriptor.
systemOamEntry	1.3.6.1.4.1.164.6.2.36.1.1		not-accessible	An entry in the OAM table.
I32 systemOamFrequency	1.3.6.1.4.1.164.6.2.36.1.1.2	Integer32	read-write	Time in sec. between 2 OAM packets.
INT systemOamLinkCheck	1.3.6.1.4.1.164.6.2.36.1.1.4	INTEGER	read-write	This MIB object determines whether continuous connectivity Link checks will be performed by the device for uplinks. For Vmux-2100: enable (3) value can be set upon device installation. In this case, TDM Link Connectivity checks can be performed even before the user configures the Links of the device.If the value is enable (3) and there is no connection with the remote side, the Test LED will blink on the Main Board Module.
systemOamTable	1.3.6.1.4.1.164.6.2.36.1		not-accessible	The OAM Configuration Table.
I32 systemOamTimeoutCycles	1.3.6.1.4.1.164.6.2.36.1.1.3	Integer32	read-write	No. of cycles the agent will send OAM packets without receiving a response from the remote device before declaring that the connection to the remote side is down - Time Out.
I32 systemParameter	1.3.6.1.4.1.164.6.2.18	Integer32	read-write	This parameter can be used for different purposes: - TELNET session time-out in seconds. - Ace20: when trying to create row in a table that already has row with the same values, if set of values has to be unique in table, this attribute is set to the index of the existing row. - Optimux-T3: when CH interfaces are RJ-45, user can select via this object, the interface type for each Group of channels: T1 or E1: The selection will be a sum of the following Bits. '0' = T1 '1' = E1 Bit Group Value for each Bit having '1' 1 1 (CH-1..CH-8) 1 2 2 (CH-9..CH-12) 2 3 3 (CH-13..CH-20) 4 4 4 (CH-21..CH-28) 8 Examples: 15 = all Groups are selected to be E1 6 = Group 2 and Group 3 are selected to be E1 (Group 1 and Group 4 are T1). - FCD-A, FCD-M: user can select via this object the configuration used for Get values of MSDSL parameters that don't have configuration index. 1 =active configuration 255=temporary configuration. Set of this object should be done before Getting the MSDSL RW parameters. - Ace2002: This parameter indicates the number of intervals that were successfully uploaded upon statistics collection session. - FCD-IP, WR, FCD-IPD, LA-240: This parameter indicates whether Telnet Access is enabled/disabled: Values: 2 - Telnet Access is Disabled. 3 - Telnet Access is Enabled. -Vmux-110: This parameter value equals to maximum number of bundles. -Optimux-155: Simmilar usage to Optimux T3. user can select via this object, interface type T1 or E1 for each Group of channels (LIU): LIU group consists of 7 channels. Up to 12 LIUs are represented (84 T1 Channels). The selection will be a sum of the 2**n For each bit:'0' = T1 ,'1' = E1 Bit Group 1 1 (CH-1 .. CH-7) 2 2 (CH-8 .. CH-14) 3 3 (CH-15 ..CH-21) ... 9 9 (CH-56.. CH-63) ... 10 10 (CH-64..CH-70) 11 11 (CH-71..CH-77) 12 12 (CH-78..CH-84)
systemPort	1.3.6.1.4.1.164.6.2.15
systemPsEntry	1.3.6.1.4.1.164.6.2.25.1		not-accessible	An entry in table.
INT systemPsHotSwap	1.3.6.1.4.1.164.6.2.25.1.5	INTEGER	read-only	Is PS unit hot swap or fixed.
I32 systemPsIndex1	1.3.6.1.4.1.164.6.2.25.1.1	Integer32	read-only	First Index. In HUBs: 1 = PS-A slot 2 = PS-B slot 3 = PS-C slot. In SA units: 1 = PS1 2 = PS2 Default = 1
I32 systemPsIndex2	1.3.6.1.4.1.164.6.2.25.1.2	Integer32	read-only	Second Index. In HUBs: 1 always. In SA units: 1 = Local 2 = Remote Default = 1.
INT systemPsStatus	1.3.6.1.4.1.164.6.2.25.1.4	INTEGER	read-only	The Status of the PS unit.
systemPsTable	1.3.6.1.4.1.164.6.2.25		not-accessible	This table describes the PS types of a device. Usage of this table is specified in the device's NMS SRS
INT systemPsType	1.3.6.1.4.1.164.6.2.25.1.3	INTEGER	read-only	The type of PS, for a stand-alone product. acDc - PS that supports both AC and DC. acPF - Power Feeding (phantom) box that is feeding another box by external AC. dcPF - Power Feeding (phantom) box that is feeding another box by external DC.
INT systemReset	1.3.6.1.4.1.164.6.2.13	INTEGER	read-write	Reset action to be performed on the system. - resetMapping - reset SDH/SONET mapping to default for all SDH/SONET links. - resetStandby(6) - can be used only by devices with redundancy on MAIN/CL.
INT systemResetAllStatsCmd	1.3.6.1.4.1.164.6.2.16	INTEGER	read-write	Reset statistics of all ports and connections of the device.
systems	1.3.6.1.4.1.164.6.1
INT systemSaveAndResetAllStatsCmd	1.3.6.1.4.1.164.6.2.23	INTEGER	read-write	on - a command to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. off - agent will automatically change to this value, after performing the command.
systemsEvents	1.3.6.1.4.1.164.6.1.0			The events for RAD products.
STR systemTime	1.3.6.1.4.1.164.6.2.14.2	DisplayString	read-write	System time.
I32 systemTimeElapsed	1.3.6.1.4.1.164.6.2.14.3	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period. Same for all ports of the device.
systemTiming	1.3.6.1.4.1.164.6.2.14
NTF systemTrap	1.3.6.1.4.1.164.6.1.3.0.6			This trap alerts of major problems in the device.
systemVoice	1.3.6.1.4.1.164.3.1.2.12
INT systemVoiceCoderAndRate	1.3.6.1.4.1.164.3.1.2.12.1.1.7	INTEGER	read-write	This object indicates the Coder and Rate for the Voice Compression.
INT systemVoiceCoderCoderAndRate	1.3.6.1.4.1.164.3.1.2.12.2.1.3	INTEGER	read-write	This object indicates the Coder and Rate for the Voice Compression.
U32 systemVoiceCoderConfIdx	1.3.6.1.4.1.164.3.1.2.12.2.1.1	Unsigned32	not-accessible	The first index of the table. This object might represent the Configuration Index (1..100) being accessed; Index=255 relates to the TmpCnfg. For devices with multiple configurations, Set is permitted to TmpCnfg(255) only. Not-Applicable = 1.
systemVoiceCoderEntry	1.3.6.1.4.1.164.3.1.2.12.2.1		not-accessible	An entry in Voice Coders table.
U32 systemVoiceCoderPriority	1.3.6.1.4.1.164.3.1.2.12.2.1.2	Unsigned32	not-accessible	This object indicates the Coder's Priority.
systemVoiceCoderTable	1.3.6.1.4.1.164.3.1.2.12.2		not-accessible	Voice Coders table.
I32 systemVoiceConfIdx	1.3.6.1.4.1.164.3.1.2.12.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed - Active or Temporary Configurations. Idx 255 relates to the temporary TmpCnfg. All configurations can be read but only the Temporary can be written to.
INT systemVoiceDtmfRelayMethod	1.3.6.1.4.1.164.3.1.2.12.1.1.10	INTEGER	read-write	This object indicates the DTMF Relay Method that is used to transmit DTMF tones. rfc2833(1) - inband DTMF relay according to RFC-2833. sipInfo(2) - out of band DTMF relay using SIP INFO method.
INT systemVoiceDtmfRelayPayloadTypeNeg	1.3.6.1.4.1.164.3.1.2.12.1.1.12	INTEGER	read-write	This object indicates whether Payload Type Negotiation is used (according to RFC-2833) or not. It is relevant only when DTMF Relay Method is RFC-2833.
U32 systemVoiceDtmfRelayRxPayloadType	1.3.6.1.4.1.164.3.1.2.12.1.1.11	Unsigned32	read-write	This object indicates the Rx Payload Type for DTMF relay RTP packets. It is relevant only when DTMF Relay Method is RFC-2833.
U32 systemVoiceDtmfRelayTxPayloadType	1.3.6.1.4.1.164.3.1.2.12.1.1.13	Unsigned32	read-write	This object indicates the Tx Payload Type for DTMF relay RTP packets. It is relevant only when the Payload Type Negotiation is disabled.
INT systemVoiceEchoCanceler	1.3.6.1.4.1.164.3.1.2.12.1.1.8	INTEGER	read-write	This object indicates the Echo Canceler activation.
systemVoiceEntry	1.3.6.1.4.1.164.3.1.2.12.1.1		not-accessible	An entry in table.
INT systemVoiceFaxRate	1.3.6.1.4.1.164.3.1.2.12.1.1.5	INTEGER	read-write	This object indicates the Fax Rate limit. It is irrelevant when Fax support is NA or disabled.
INT systemVoiceFaxSupport	1.3.6.1.4.1.164.3.1.2.12.1.1.4	INTEGER	read-write	This object allows the user to Disable/Enable Fax support.
INT systemVoiceModemSupport	1.3.6.1.4.1.164.3.1.2.12.1.1.6	INTEGER	read-write	This object allows the user to Disable/Enable Modem support.
INT systemVoiceNationalTone	1.3.6.1.4.1.164.3.1.2.12.1.1.2	INTEGER	read-write	Tone Characteristics (Amplitude, Frequency, delays etc.). These characteristics are defined according to the country.
U32 systemVoicePacketRate	1.3.6.1.4.1.164.3.1.2.12.1.1.3	Unsigned32	read-write	This object indicates the G.729 and G.711 Coders transmitted Packet Rate in milliseconds.
systemVoiceTable	1.3.6.1.4.1.164.3.1.2.12.1		not-accessible	General Parameters for voice - system level.
I32 systemVoiceTxGain	1.3.6.1.4.1.164.3.1.2.12.1.1.9	Integer32	read-write	This object indicates the Transmit Gain (volume) in dB.
OCT tftpError	1.3.6.1.4.1.164.6.2.12.7	OCTET STRING	read-only	The MSB represents the standard error code. The LSB represents the private error code. 0x0000 is No Error 0x0100 is File Not Found 0x0200 is Access violation 0x0300 is Disk full or allocation exceeded 0x0400 is Illegal TFTP operation 0x0500 is Unknown transfer ID 0x0600 is File already exists 0x0700 is No such user 0x0001 is Server Overflow 0x0002 is No empty UDP port 0x0003 is No empty connection 0x0004 is Illegal File Mode 0x0007 is Illegal PDU size 0x0008 is TFTP Server does not exist 0x0009 is Incorrect File 0x000A is Wrong License format 0x000B is License ID already used
I32 tftpRetryTimeOut	1.3.6.1.4.1.164.6.2.12.4	Integer32	read-write	General Retransmission time-out value (seconds)
INT tftpStatus	1.3.6.1.4.1.164.6.2.12.6	INTEGER	read-write	Status of tftp session. When a session ended with success, the tftpStatus should be endedOk(6). Before restarting a tftp session, the NMS should set the tftpStatus to noOp(2). That's the reason of MAX-ACCESS read-write to this field.
NTF tftpStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.1			This trap is sent whenever the status of tftp changed.
I32 tftpTotalTimeOut	1.3.6.1.4.1.164.6.2.12.5	Integer32	read-write	Total Retransmission time-out value (seconds)
trapEntry	1.3.6.1.4.1.164.6.2.11.1		not-accessible	An entry in trapTable.
I32 trapID	1.3.6.1.4.1.164.6.2.11.1.1	Integer32	read-only	This object indicates an index of a specific trap. Can be used also for any trap, while trapVal is used as 'accessible-for-notify' or trapNumeric is used.
I32 trapNumeric	1.3.6.1.4.1.164.6.2.11.1.4	Integer32	accessible-for-notify	This object is a numeric general parameter, that can be attached to any trap. Values can be positive or negative.
trapTable	1.3.6.1.4.1.164.6.2.11		not-accessible	This table may include the last few traps generated by the agent, for future retrieval. The table has a limited capacity. If traps are not retrieved in proper time, they will be over-written by new traps. For other devices, it can include generic variables that will be attached to traps as 'accessible-for-notify'.
TIK trapTimeSinceOccurrence	1.3.6.1.4.1.164.6.2.11.1.3	TimeTicks	read-only	This object indicates the amount of time passed since the occurrence of the event that triggered this trap.
STR trapVal	1.3.6.1.4.1.164.6.2.11.1.2	DisplayString	read-only	This object is the actual ASCII description of the trap. It can be used also as attached variable of traps, in order to detail in explicit ASCII text, data of the trap. In this case, it is used as 'accessible-for-notify'.
unknown	1.3.6.1.4.1.164.6.1.7.9
wanGen	1.3.6.1.4.1.164.3.1
webranger	1.3.6.1.4.1.164.11.7.2
wfq	1.3.6.1.4.1.164.6.3.1
I32 wfqCnfgIdx	1.3.6.1.4.1.164.6.3.1.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
wfqEntry	1.3.6.1.4.1.164.6.3.1.1.1		not-accessible	An entry in the Weighted Fair Queueing table.
U32 wfqMaxPacketSize	1.3.6.1.4.1.164.6.3.1.1.1.9	Unsigned32	read-create	The size of the largest packet which can be received on this queue, specified in octets. Packets larger than this size will be discarded.
U32 wfqMinRateAbsolute	1.3.6.1.4.1.164.6.3.1.1.1.8	Unsigned32	read-create	The minimum absolute rate, in kbps, that should be allocated to this queue. If the value is zero, then there is effectively no minimum rate guarantee. If the value is non-zero, then the servicing of this queue in at least this rate is assured. Note that when this attribute is being used, the wfqWeightValue attribute is NA.
I32 wfqPrtIdx	1.3.6.1.4.1.164.6.3.1.1.1.2	Integer32	not-accessible	This object indicates a unique port or interface number, for which Weighted Fair Queueing table is applicable . For numbering, see product's spec. For some products, the numbering can equal ifIndex. Value of 255 (not applicable) refer to system level queue
I32 wfqQueueIdx	1.3.6.1.4.1.164.6.3.1.1.1.4	Integer32	not-accessible	This object indicates a queue index. For FCD-155, valid queues are 1..3. The 4th queue is not in MIB. Its weight will be RO, Calculated according to the sum of the 3 first queues.
ROW wfqRowStatus	1.3.6.1.4.1.164.6.3.1.1.1.5	RowStatus	read-create	This object enables Creation/Deletion of rows in the WFQ table. For FCD-155, rows are not created nor destroyed by user.
INT wfqSchedulingMode	1.3.6.1.4.1.164.6.3.1.1.1.7	INTEGER	read-create	This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme or priority Queue (Strict Priority).
wfqTable	1.3.6.1.4.1.164.6.3.1.1		not-accessible	This table allows user to define several WFQ tables per output port. WFQ supports flows with different bandwidth requirements by giving each queue a weight that assigns it a different percentage of output port bandwidth. When Weighted Fair Queuing is used, it is possible to precisely attribute bandwidth partitioning among the queues. When there is congestion, each class (queue) is not allowed to use more bandwidth than the amount allocated to it.
I32 wfqTblIdx	1.3.6.1.4.1.164.6.3.1.1.1.3	Integer32	not-accessible	This object indicates which Weighted Fair Queueing (WFQ) Table is being used. There can be several tables. For FCD-155 User will select which one will be used for a virtual concatenation group.Valid values are 1,2
I32 wfqWeightValue	1.3.6.1.4.1.164.6.3.1.1.1.6	Integer32	read-create	This object indicates a relative weight value. User should make sure that the sum of values for all queues will not exceed 100% (sum should be BELOW 100% in order to leave some BW percentage for last queue) Note that when this attribute is being used, the wfqMinRateAbsolute attribute is NA.
INT wrAutoLearnLanIpxNets	1.3.6.1.4.1.164.11.7.2.3.1	INTEGER	read-write	Activating (disable/enable) the auto-learn operation.
INT wrBraodcastCtrlCmd	1.3.6.1.4.1.164.11.7.2.1.1	INTEGER	read-write	This parameter is a command to the webranger CPU. It enables blocking or forwarding broadcast frames, which may cause a trigger to a connection. block (1) - blocks the broadcast frames. forward (2) - forwards the broadcast frames. blockLinkPropagation (3) - blocks the broadcast frames to the links, tx to the LAN.
wrConfigIpDhcp	1.3.6.1.4.1.164.11.7.2.2.1
wrConfigIpDNS	1.3.6.1.4.1.164.11.7.2.2.2
wrConfigIpxRouterInfo	1.3.6.1.4.1.164.11.7.2.3
INT wrDhcpAction	1.3.6.1.4.1.164.11.7.2.2.1.1	INTEGER	read-write	Activating (disable/enable) DHCP server operation. Since DHCP Server and DHCP Relay cannot reside in same device, DHCP Relay may be enabled (per interface), only if server action is disabled. For some devices, this object is used in order to enable/disable the DHCP Client. See device SDS.
STR wrDhcpConfigFileName	1.3.6.1.4.1.164.11.7.2.2.1.2.1.12	SnmpAdminString	read-create	TFTP-name of the configuration File Name for DHCP pool.
IP wrDhcpDefaultGateway	1.3.6.1.4.1.164.11.7.2.2.1.2.1.4	IpAddress	read-create	Default Gateway's IP Address.
wrDhcpEntry	1.3.6.1.4.1.164.11.7.2.2.1.2.1		not-accessible	DHCP parameters per entry of the DHCP table.
IP wrDhcpHighIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.2	IpAddress	read-create	DHCP High Ip Address.
INT wrDhcpInterface	1.3.6.1.4.1.164.11.7.2.2.1.2.1.7	INTEGER	read-create	The IP addresse allocation is done according to the interface type from which the DHCP request arrives.
I32 wrDhcpIpAddressLeaseTime	1.3.6.1.4.1.164.11.7.2.2.1.2.1.9	Integer32	read-create	Allocated IP Address lease time in seconds. A zero value specifies no time limitation.
IP wrDhcpIpMaskAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.3	IpAddress	read-create	IP mask Address.
IP wrDhcpLowIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.1	IpAddress	read-create	DHCP Low Ip Address.
STR wrDhcpPoolName	1.3.6.1.4.1.164.11.7.2.2.1.2.1.10	SnmpAdminString	read-create	DHCP pool name - string with max length of 10 characters
INT wrDhcpPort	1.3.6.1.4.1.164.11.7.2.2.1.5	INTEGER	read-write	This parameter defines the port that DHCP flow will be actiavted.
IP wrDhcpPrimaryDNS	1.3.6.1.4.1.164.11.7.2.2.1.2.1.5	IpAddress	read-create	Primary DNS.
ROW wrDhcpRowStatus	1.3.6.1.4.1.164.11.7.2.2.1.2.1.8	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrDhcpRowStatus.id = active(1). For destroying a row, the NMS should set: wrDhcpStatus.id = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
IP wrDhcpSecondaryDNS	1.3.6.1.4.1.164.11.7.2.2.1.2.1.6	IpAddress	read-create	Secondary DNS.
wrDhcpTable	1.3.6.1.4.1.164.11.7.2.2.1.2		not-accessible	A list of DHCP entries. The number of entries is up to DHCP current entries, according to the WEBRANger model.
IP wrDhcpTftpServerIp	1.3.6.1.4.1.164.11.7.2.2.1.2.1.11	IpAddress	read-create	DHCP pool - TFTP-server IP Address.
IP wrDialInIpxNet	1.3.6.1.4.1.164.11.7.2.3.3	IpAddress	read-write	Net address through a link.
INT wrDNSRelayAction	1.3.6.1.4.1.164.11.7.2.2.2.1	INTEGER	read-write	When Enabled, device will act as a DNS Relay: whenever the device receives a DNS request from its host, it will forward it to the DNS server as if the request was initiated by the device itself. The reply from the DNS server is forwarded by the device to the host as if the device was answering the request.
INT wrFrCllmMessages	1.3.6.1.4.1.164.11.7.2.4.5.1.2	INTEGER	read-write	This parameter enables/disables the Webranger to Tx/Rx CLLM (Consolidated Link Layer Management) messages via DLCI 1023. The CLLM messages are link layer control messages. They can be used for example in cases of congestion. The CLLM message contains a code for cause of congestion and list of all DLCIs that should act to reduce data transmission.
wrFrCnfgEntry	1.3.6.1.4.1.164.11.7.2.4.5.1		not-accessible	Configuration entry for Fr parameters that do not exist in RFC2115.
wrFrCnfgTable	1.3.6.1.4.1.164.11.7.2.4.5		not-accessible	Configuration table for Fr parameters that do not exist in RFC2115.
INT wrFrDlciLearningMode	1.3.6.1.4.1.164.11.7.2.4.5.1.1	INTEGER	read-write	This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol for the current interface. off - the WR will read the user's configuration for this interface. on - the WR will begin self learning of the current interface's maintanance protocol and DLCIs.
INT wrFrSelfLearningMode	1.3.6.1.4.1.164.11.7.2.1.2	INTEGER	read-write	This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol. off - will get the configuration by setting it. on - disables configuration and start self learning.
INT wrGratuitousArp	1.3.6.1.4.1.164.11.7.2.1.3	INTEGER	read-write	This parameter enables/disables the Gratuitous ARP feature. When enabled, the feature means: when receiving ARP with sender's Source IP Address that already exists in the ARP table - replace MAC Address with sender's Source MAC Address.
wrInterface	1.3.6.1.4.1.164.11.7.2.4
IP wrIpAddress	1.3.6.1.4.1.164.11.7.2.4.1.1.2	IpAddress	read-create	Link IP Address.
wrIpAddressEntry	1.3.6.1.4.1.164.11.7.2.4.1.1		not-accessible	Ip Address per Link
wrIpAddressTable	1.3.6.1.4.1.164.11.7.2.4.1		not-accessible	Link IP addresses Table.
I32 wrIpIfIndex	1.3.6.1.4.1.164.11.7.2.4.1.1.1	Integer32	read-only	Port interface index.
IP wrIpMask	1.3.6.1.4.1.164.11.7.2.4.1.1.3	IpAddress	read-create	Link IP mask Address.
wrIpRouterInfo	1.3.6.1.4.1.164.11.7.2.2
ROW wrIpRowStatus	1.3.6.1.4.1.164.11.7.2.4.1.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrIpRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrIpRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
IP wrIpxNetAddress	1.3.6.1.4.1.164.11.7.2.3.2.1.3	IpAddress	read-write	Net address per Frame Type & LAN port.
INT wrLanBridgeRouterMode	1.3.6.1.4.1.164.11.7.2.4.3.1.2	INTEGER	read-write	This parameter indicates whether the link is Bridge or Router and specifies the Router's type.
wrLanIfEntry	1.3.6.1.4.1.164.11.7.2.4.3.1		not-accessible	Ip Address per Link
I32 wrLanIfIndex	1.3.6.1.4.1.164.11.7.2.3.2.1.1	Integer32	read-only	LAN port ifIndex.
I32 wrLanIfRdnTimeout	1.3.6.1.4.1.164.11.7.2.4.3.1.4	Integer32	read-write	LAN Redundancy Timeout in seconds. Applicable when wrLanIfState=redundancy.
INT wrLanIfState	1.3.6.1.4.1.164.11.7.2.4.3.1.3	INTEGER	read-write	The LAN is disabled or enabled. For LAN 2 it can be also 'redundancy'.
wrLanIfTable	1.3.6.1.4.1.164.11.7.2.4.3		not-accessible	Link IP addresses Table.
INT wrLanIpxFrameType	1.3.6.1.4.1.164.11.7.2.3.2.1.2	INTEGER	read-only	Frame Type
wrLanIpxNetEntry	1.3.6.1.4.1.164.11.7.2.3.2.1		not-accessible	IPX Nets per frame type & LAN port. The table entries will be created by the agent
wrLanIpxNetTable	1.3.6.1.4.1.164.11.7.2.3.2		not-accessible	Lan IPX nets Table.
I32 wrSpoofingAction	1.3.6.1.4.1.164.11.7.2.4.2.1.2	Integer32	read-create	Spoofing action is applied by bit code: enable : bit 0 set (disable: bit 0 is 0) keepAlive : bit 1 ... : bit 2 and so on. For the above example, to set spoofing to keepAlive action, the object's value will be 3 = [ 20 + 21 ] Only the Remote WEBRANger will accept this object ! -------
I32 wrSpoofingAgingStation	1.3.6.1.4.1.164.11.7.2.4.2.1.3	Integer32	read-create	Aging time of stations list, in min. The agent 'translates' the time entered in minutes, to 10 min. resolution, as follows: 1..10 min - 10 min 11..20 min - 20 min and so on... 0 is not a valid value. Only the Remote WEBRANger will accept this object ! ----------------
wrSpoofingEntry	1.3.6.1.4.1.164.11.7.2.4.2.1		not-accessible	Spoofing per Link
I32 wrSpoofingIfIndex	1.3.6.1.4.1.164.11.7.2.4.2.1.1	Integer32	read-only	Port interface index.
ROW wrSpoofingRowStatus	1.3.6.1.4.1.164.11.7.2.4.2.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrSpoofingRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrSpoofingRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
wrSpoofingTable	1.3.6.1.4.1.164.11.7.2.4.2		not-accessible	Spoofing Table.
INT wrSyncClkMode	1.3.6.1.4.1.164.11.7.2.4.4.1.2	INTEGER	read-write	Clock Mode.
INT wrSyncClkRate	1.3.6.1.4.1.164.11.7.2.4.4.1.3	INTEGER	read-write	Clock Rate in. Rate can be changed if Clock Mode is Program only.
wrSyncCnfgEntry	1.3.6.1.4.1.164.11.7.2.4.4.1		not-accessible	Configuration table
wrSyncCnfgTable	1.3.6.1.4.1.164.11.7.2.4.4		not-accessible	Configuration table for Async interface.
I32 wrSyncIfIndex	1.3.6.1.4.1.164.11.7.2.4.4.1.1	Integer32	read-only	Sync interface index.
wrSysConfig	1.3.6.1.4.1.164.11.7.2.1
INT xcAdminStatus	1.3.6.1.4.1.164.6.2.31.1.8	INTEGER	read-create	The desired administrative status of this bi-directional cross-connect.
INT xcAttachedIfType	1.3.6.1.4.1.164.6.2.31.1.10	INTEGER	read-only	This object indicates if the specific VCC is already attached to any interface, and indicates the type of the interface. This object's purpose is to ease the checking to the NMS. notApplicable - used for entries that are not LAN (as HDLC), or when the VCC was attached to a bridge, or when this parameter is irrelevant. free - the LAN VCC wasn't attached yet to any router interface. routerAtm - attached to an ATM router interface. lis - attached to a LIS interface.
I32 xcBitMapping	1.3.6.1.4.1.164.6.2.31.1.12	Integer32	read-only	This object maps this entry to a bit of an octet string. For ACE2002 this object maps the LAN VCC to the bit of the VLAN Port Lists. If the value is '0' then it means that this VCC is not mapped to a port list or it may be an HDSL entry.
STR xcDescr	1.3.6.1.4.1.164.6.2.31.1.7	DisplayString	read-create	A textual string containing information about the xc entry.
xcEntry	1.3.6.1.4.1.164.6.2.31.1		not-accessible	An entry in table.
I32 xcIfIndex1	1.3.6.1.4.1.164.6.2.31.1.2	Integer32	not-accessible	The interface Index from the ifTable, which identify one side of the connection.
I32 xcIfIndex2	1.3.6.1.4.1.164.6.2.31.1.5	Integer32	not-accessible	The interface Index from the ifTable, which identifies the other side of the connection.
I32 xcIndex	1.3.6.1.4.1.164.6.2.31.1.1	Integer32	not-accessible	Cross Connect Identifier.
I32 xcIndexNext	1.3.6.1.4.1.164.6.2.30	Integer32	read-only	This object contains an appropriate value to be used for xcIndex when creating entries in the xcTable. The value 0 indicates that no unassigned entries are available. To obtain the xcIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
I32 xcInputPriority	1.3.6.1.4.1.164.6.2.31.1.11	Integer32	read-create	This object is the priority, by which the LAN frames will be internaly sent to the ATM HW. This parameter is applicable if atmNteMdlInputPriorityMechanism=enabled. 1 - Highest priority. Will be the first to be sent to the ATM HW. 4 - Lowest priority. Will be the last to be sent to the ATM HW.
INT xcOperStatus	1.3.6.1.4.1.164.6.2.31.1.9	INTEGER	read-only	The operational status of this bi-directional cross-connect.
ROW xcRowStatus	1.3.6.1.4.1.164.6.2.31.1.6	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table.
xcTable	1.3.6.1.4.1.164.6.2.31		not-accessible	Configuration of system cross-connect entries. The table follows the behavior described in RFC 2515, RFC 1604 regarding the creation deletion and modification of an entry within the table.
I32 xcVci	1.3.6.1.4.1.164.6.2.31.1.4	Integer32	not-accessible	The VCI value.
I32 xcVpi	1.3.6.1.4.1.164.6.2.31.1.3	Integer32	not-accessible	The VPI value.
NTF xModemFileTransferStatusTrap	1.3.6.1.4.1.164.6.1.0.22			This trap is sent in the following cases: - When an xModem File Transfer Session begins. In this case, the trapVal.1 string sent will be: 'Start'. - When an xModem File Transfer Session ends. In this case, the trapVal.1 string sent will be one of the following, according to the way the session ended : - 'End: OK' - 'End: Failed'

OID symbolic	OID numeric	Type	Access	Description
rad	1.3.6.1.4.1.164
radTokenRing	1.3.6.1.4.1.164.1
radFddi	1.3.6.1.4.1.164.2
radWan	1.3.6.1.4.1.164.3
wanGen	1.3.6.1.4.1.164.3.1
chasWanGen	1.3.6.1.4.1.164.3.1.1
STR chasVersion	1.3.6.1.4.1.164.3.1.1.1	DisplayString	read-only	An ASCII string for description and display of the agent chassis version.
I32 chasTotalNoOfSlt	1.3.6.1.4.1.164.3.1.1.2	Integer32	read-only	This entry indicates the number of physical slots in the chassis.
I32 chasTotalNoOfIoSlt	1.3.6.1.4.1.164.3.1.1.3	Integer32	read-only	This entry indicates the total number of physical IO slots in the chassis, (not all slots hardware should be occupied and active) .
I32 chasTotalNoOfPsSlt	1.3.6.1.4.1.164.3.1.1.4	Integer32	read-only	This entry indicates the number of physical Power Supply slots in the chassis.
I32 chasTotalNoOfClSlt	1.3.6.1.4.1.164.3.1.1.5	Integer32	read-only	This entry indicates the number of physical Common Logic slots in the chassis.
agnWanGen	1.3.6.1.4.1.164.3.1.2
statAgnGen	1.3.6.1.4.1.164.3.1.2.1
INT agnSDateFormat	1.3.6.1.4.1.164.3.1.2.1.1	INTEGER	read-write	This entry indicates the date and time format used for the agnSDateAndTimeCmd and for the alarm history report.
STR agnSDateCmd	1.3.6.1.4.1.164.3.1.2.1.2	DisplayString	read-write	This entry indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent.
STR agnSTimeCmd	1.3.6.1.4.1.164.3.1.2.1.3	DisplayString	read-write	This entry indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent.
I32 agnSActiveCnfg	1.3.6.1.4.1.164.3.1.2.1.4	Integer32	read-only	This entry specifies the unique identifier of the configuration, that is currently active and running.
I32 agnSEditCnfg	1.3.6.1.4.1.164.3.1.2.1.5	Integer32	read-only	This entry indicates the unique identifier of the configuration that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process.
STR agnSLastCnfgFlipTime	1.3.6.1.4.1.164.3.1.2.1.6	DisplayString	read-only	This entry indicates the Date & Time of the last flip to the current configuration at the agent.
STR agnSLastCnfgFlipCause	1.3.6.1.4.1.164.3.1.2.1.7	DisplayString	read-only	This entry describes the flip's cause.
INT agnSEditBy	1.3.6.1.4.1.164.3.1.2.1.8	INTEGER	read-only	This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after an update(load) operation.
INT agnSClkSrc	1.3.6.1.4.1.164.3.1.2.1.9	INTEGER	read-only	This entry indicates the source of the system clock.
INT agnSAlrStatus	1.3.6.1.4.1.164.3.1.2.1.10	INTEGER	read-only	Indicates the alarm state in the agent level, i.e. lower level (card/port) alarms not included. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSAlrStatusAll	1.3.6.1.4.1.164.3.1.2.1.11	INTEGER	read-only	Indicates the alarm state of the entire agent, i.e. including card and port alarms status. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSMaskedAlrStat	1.3.6.1.4.1.164.3.1.2.1.12	INTEGER	read-only	Indicates the alarm state in the agent level,[ i.e. lower level (card/port) alarms not included] including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSMaskedAlrStatAll	1.3.6.1.4.1.164.3.1.2.1.13	INTEGER	read-only	Indicates the alarm state of the entire agent, i.e. including card and port alarms status,including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSTstStatAll	1.3.6.1.4.1.164.3.1.2.1.14	INTEGER	read-only	on(3) - when there is at least one test in progress in one of the agent cards, otherwise the value will be off(2).
agnSAlrTable	1.3.6.1.4.1.164.3.1.2.1.15		not-accessible	List of agent related alarms and indications for alarms at system level.
agnSAlrEntry	1.3.6.1.4.1.164.3.1.2.1.15.1		not-accessible	An entry in table.
I32 agnSAlrIdx	1.3.6.1.4.1.164.3.1.2.1.15.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
STR agnSAlrCodeDescription	1.3.6.1.4.1.164.3.1.2.1.15.1.2	DisplayString	read-only	This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
I32 agnSAlrCode	1.3.6.1.4.1.164.3.1.2.1.15.1.3	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at system level.
INT agnSAlrSeverity	1.3.6.1.4.1.164.3.1.2.1.15.1.4	INTEGER	read-only	The severity of the alarm.
INT agnSAlrState	1.3.6.1.4.1.164.3.1.2.1.15.1.5	INTEGER	read-only	State of the alarm.
I32 agnSAlrCounter	1.3.6.1.4.1.164.3.1.2.1.15.1.6	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
INT agnSAlrMask	1.3.6.1.4.1.164.3.1.2.1.15.1.7	INTEGER	read-only	Alarm mask : on/off.
INT agnSAlrInvert	1.3.6.1.4.1.164.3.1.2.1.15.1.8	INTEGER	read-only	Alarm invert : on/off.
INT agnSClearAlrCmd	1.3.6.1.4.1.164.3.1.2.1.16	INTEGER	read-write	Setting this attribute to ON, enforce a clear operation on all the agent(general) events. General alarms are alarms which are not specific to a card or port. The clear operation will not be applied for masked/inverted alarms.
INT agnSClearAllAlrCmd	1.3.6.1.4.1.164.3.1.2.1.17	INTEGER	read-write	Setting this attribute to ON, enforce a clear operation on all MUX alarm events at the levels of agent, slots and ports. The clear operation will not be applied for masked/inverted alarms.
INT agnSSanityCheckStatus	1.3.6.1.4.1.164.3.1.2.1.18	INTEGER	read-only	Upon completion of the Sanity check process on the TmpCnfg this attribute will be set to: FAIL(2) - when there is at least one error encountered and possibly some warnings. WARNING(3) - when there are only warnings. otherwise, the value will be OK(4). The value will be UNKNOWN(1) if changes were made in the TmpCnfg following the last Sanity check.
I32 agnSNoOfSanityCheckErr	1.3.6.1.4.1.164.3.1.2.1.19	Integer32	read-only	This entry indicates the number of errors/warnings discovered by the last SanityCheck process.
agnSErrListTable	1.3.6.1.4.1.164.3.1.2.1.20		not-accessible	List of errors and warnings found during Sanity Check process.
agnSErrListEntry	1.3.6.1.4.1.164.3.1.2.1.20.1		not-accessible	An entry in table.
I32 agnSErrIdx	1.3.6.1.4.1.164.3.1.2.1.20.1.1	Integer32	read-only	Unique number to identify an entry in the error list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'.
STR agnSErrDescription	1.3.6.1.4.1.164.3.1.2.1.20.1.2	DisplayString	read-only	This attribute is a full text description of the sanity check error including error code, slot and port numbers related to the code .
I32 agnSMaxNoOfCnfg	1.3.6.1.4.1.164.3.1.2.1.21	Integer32	read-only	Maximum number of configurations that can be defined and stored in the MUX. If the mux has a large capacity, the maximum will be limited to 254.
agnSCnfgTable	1.3.6.1.4.1.164.3.1.2.1.22		not-accessible	This table contains an entry per configuration. It indicates if the configuration is valid.
agnSCnfgEntry	1.3.6.1.4.1.164.3.1.2.1.22.1		not-accessible	An entry in table.
I32 agnSEntryIdx	1.3.6.1.4.1.164.3.1.2.1.22.1.1	Integer32	read-only	Unique number to identify an entry in the configuration table.
INT agnSEntryIsValid	1.3.6.1.4.1.164.3.1.2.1.22.1.2	INTEGER	read-only	This attribute indicates whether the specific configuration is valid in the MUX . Value of NO indicates: no such configuration in the MUX.
cnfgAgnGen	1.3.6.1.4.1.164.3.1.2.2
INT agnCSanityCheckCmd	1.3.6.1.4.1.164.3.1.2.2.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion the value will automatically be changed to off(2).
I32 agnCSaveCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.2	Integer32	read-write	This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown
I32 agnCLoadCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.3	Integer32	read-write	This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on Valid configurations (agnSEntryIsValid)
agnCClkSrcTable	1.3.6.1.4.1.164.3.1.2.2.4		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
agnCClkSrcEntry	1.3.6.1.4.1.164.3.1.2.2.4.1		not-accessible	An entry in table.
I32 agnCClkCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..100) being accessed and Idx 255 relates to the TmpCnfg.
I32 agnCClkSrcIdx	1.3.6.1.4.1.164.3.1.2.2.4.1.2	Integer32	read-only	An index to the table. There are only two entries to this table. Index 1 points to the Master clock parameters and Index 2 points to the Fallback clock parameters
INT agnCClkSrcMode	1.3.6.1.4.1.164.3.1.2.2.4.1.3	INTEGER	read-write	The source of the nodal timing.
INT agnCClkSrcSlt	1.3.6.1.4.1.164.3.1.2.2.4.1.4	INTEGER	read-write	This entry is valid only when we are working in rxClk mode. For an invalid entry, the return value will be '7fff'h.
I32 agnCClkSrcPrt	1.3.6.1.4.1.164.3.1.2.2.4.1.5	Integer32	read-write	This entry is valid only when we are working in rxClk or adaptive mode. For an invalid entry, the return value will be '7fff'h. - For rxClk mode, the values can be: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , notApplicable (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) - For adaptive mode, the value will be the ifIndex of the selected IP Bundle.
I32 agnCDeleteCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.5	Integer32	read-write	Setting this attribute will delete the requested DB from the NVRAM .
I32 agnCDefaultCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.6	Integer32	read-write	Setting this attribute will define the desired working configuration when no conditions of the Flip DB Table are fulfilled and no Net GO command was issued. This command will be accepted only if the Configuration number exists (agnSEntryIsValid=yes).
agnCnfgDataTable	1.3.6.1.4.1.164.3.1.2.2.7		not-accessible	This table contains data about the agent configurations. The table will support only data about valid configurations of the agent.
agnCnfgDataEntry	1.3.6.1.4.1.164.3.1.2.2.7.1		not-accessible	An entry in table.
I32 agnCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.7.1.1	Integer32	read-only	This object indicates the Idx of the agent' Cnfg the following objects refer. 255=Temporary Cnfg (Set is done only to this configuration).
STR agnCnfgDesc	1.3.6.1.4.1.164.3.1.2.2.7.1.2	DisplayString	read-write	This object is a description of the Configuration, entered by user, to enhance Cnfg recognition.
STR agnCnfgUpdDate	1.3.6.1.4.1.164.3.1.2.2.7.1.3	DisplayString	read-only	This object indicates the date when last update of this configuration was performed, as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. When update is performed, the agent should save the date.
STR agnCnfgUpdTime	1.3.6.1.4.1.164.3.1.2.2.7.1.4	DisplayString	read-only	This object indicates the time when last update of this configuration was performed, as it is known by the agent using its own real-time clock. When update is performed, the agent should save the time.
IP agnCnfgUpdMnger	1.3.6.1.4.1.164.3.1.2.2.7.1.5	IpAddress	read-only	This object indicates the IP Address of the Manager who performed the last update of this configuration. When update is performed, the agent should save the IP Address of the Manager who commanded the update. That will enable a manager to know if he performed the last update, or another manager did.
agnCnfgAlarm	1.3.6.1.4.1.164.3.1.2.2.8
I32 agnCnfgAlrFilterWindow	1.3.6.1.4.1.164.3.1.2.2.8.1	Integer32	read-write	Window of time, in seconds. During this Window, the alarms filter is performed. Same Window for all agent alarms that need filtering. Upon end of the Window, the state of the alarm is updated and a new Window starts. If no alarm needs filtering, this object's value will not be used.
agnCnfgAlrTable	1.3.6.1.4.1.164.3.1.2.2.8.2		not-accessible	This table enables the user to set attributes to each alarm. Setting for a non-existing entry agnCnfgAlrMask, agnCnfgAlrInvert or agnCnfgAlrFilter to 'yes'(or yesAndSave for Mask) will add this new entry to the table. Setting for an existing entry agnCnfgAlrMask/ agnCnfgAlrInvert/agnCnfgAlrFilter (one or more) to 'no' (noAndSave for Mask) so that ALL these objects' values are 'no' , will delete this entry from the table. For agnCnfgAlrMask, only if [(last saved value=noAndSave) AND (new value is 'no' or 'noAndSave')] the object's value is considered 'no' for deleting the entry. For some products (like MP, MPH, Vmux2100) the Active Alarms are always part of the table and cannot be removed even if their Mask/Invert/Filter are No.
agnCnfgAlrEntry	1.3.6.1.4.1.164.3.1.2.2.8.2.1		not-accessible	An entry in table.
I32 agnCnfgAlrCode	1.3.6.1.4.1.164.3.1.2.2.8.2.1.1	Integer32	read-only	The alarm code. The following attributes refer this code.
INT agnCnfgAlrSlot	1.3.6.1.4.1.164.3.1.2.2.8.2.1.2	INTEGER	read-only	The alarm slot. The following attributes apply for the alarm code and slot selected. all = the attributes apply to all slots. notApplicable = the selected alarm is for system level. For the Vmux2100 Main Board clA (3) is used.
I32 agnCnfgAlrPort	1.3.6.1.4.1.164.3.1.2.2.8.2.1.3	Integer32	read-only	The alarm port. The following attributes apply for the alarm code,slot and port selected. 200 = all = the attributes apply to all ports of the selected slot. When selected Slot is 'all', only 'all' or 'notApplicable' are valid Port selections. notApplicable = the selected alarm is for system or card level. =255 for MP =100 for DXC - For MP: - valid cards' ports are: exPrt1(1)..exPrt16(16) inPrt1(101)..inPrt48 (148) - IP Bundles - For DXC, the port index will include the Slot, as for all DXC tables: [(IO Slot+10)&n] ; n=odd for external ports n=even for internal ports.
INT agnCnfgAlrMask	1.3.6.1.4.1.164.3.1.2.2.8.2.1.4	INTEGER	read-write	An attribute defining the desired Mask state of an alarm . no - unmask (this command is not saved in agent's common database) noAndSave - unmask ; this command is saved in agent's common database yes - mask (this command is not saved in agent's common database) yesAndSave - mask ; this command is saved in agent's common database. Commands that are not saved, will be lost upon power-up or selected card removal.
INT agnCnfgAlrInvert	1.3.6.1.4.1.164.3.1.2.2.8.2.1.5	INTEGER	read-write	An attribute defining the desired Invert state of an alarm . no - not inverted. yes - inverted. For MP, it is not applicable for alarms that are currently OFF.
INT agnCnfgAlrFilter	1.3.6.1.4.1.164.3.1.2.2.8.2.1.6	INTEGER	read-write	An attribute defining if Filter is desired for the alarm . no - no filter. yes - filter activate. This filter is activated within a window of time defined by agnCnfgAlrFilterWindow. Its purpose is to avoid frequent changes of an alarm between ON/OFF states.
I32 agnCnfgAlrFilterSet	1.3.6.1.4.1.164.3.1.2.2.8.2.1.7	Integer32	read-write	This is a top threshold causing the alarm that passes it, to be declared Set (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at least, during the window in order to be considered ON. The maximum value will be 255. This value should be greater than the one of agnCnfgAlrFilterReset. Agents that do not support Alarms Filter, will return 0.
I32 agnCnfgAlrFilterReset	1.3.6.1.4.1.164.3.1.2.2.8.2.1.8	Integer32	read-write	This is a bottom threshold causing the alarm that does not pass it, to be declared Reset (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at most, during the window, in order to be considered OFF. This value should be less than the one of agnCnfgAlrFilterSet. Agents that do not support Alarms Filter, will return 0.
INT agnCnfgAlrSeverity	1.3.6.1.4.1.164.3.1.2.2.8.2.1.9	INTEGER	read-write	An attribute defining desired severity of an alarm code per slot/port
agnCnfgAlrReportTable	1.3.6.1.4.1.164.3.1.2.2.8.3		not-accessible	This table enables the user to configure the desired Alarm Reports according to alarms severity.
agnCnfgAlrReportEntry	1.3.6.1.4.1.164.3.1.2.2.8.3.1		not-accessible	An entry in table.
INT agnCnfgAlrReportType	1.3.6.1.4.1.164.3.1.2.2.8.3.1.1	INTEGER	read-only	The alarm report type. trap - traps will be sent only for alarms having the selected On/Off severity or higher. buffer - only alarms having the selected On/Off severity and higher, will be reported to the buffer. relay - relay contact will be activated only for alarms having the selected On severity or higher. For products having 2 relays, this is the R1 Relay. alrLedOn/alrLedBlink - user should select a higher severity (ReportOn) for alrLedBlink than for alrLedOn (Blinking Led means a more severe alarm than steady ON Led). alrLedOn - MTCL-1 Alarm Led will be ON only when agnSAlrStatusAll equals the selected severity or higher, but lower severity than that selected for 'alrLedBlink'. For products having 2 LEDs, this is the Minor LED. alrLedBlink - MTCL-1 Alarm Led will Blink only when agnSAlrStatusAll equals the selected severity or higher. For products having 2 LEDs, this is the Major LED. relay2 - relay 2 contact will be activated only for alarms having the selected On severity or higher. This is the R2 Relay.
INT agnCnfgAlrStartReportOn	1.3.6.1.4.1.164.3.1.2.2.8.3.1.2	INTEGER	read-write	This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to ON state. noReport - no Report at all (for any severity).
INT agnCnfgAlrStartReportOff	1.3.6.1.4.1.164.3.1.2.2.8.3.1.3	INTEGER	read-write	This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to OFF state. notApplicable - for 'relay','alrLedOn','alrLedBlink', 'relay2' report types, in MP. noReport - no Report at all (for any severity).
INT agnCOffsetCmd	1.3.6.1.4.1.164.3.1.2.2.9	INTEGER	read-write	An object defining special user request. notApplicable - is RO value for products that do not support this object. normal - nothing special u1 - user 1 - for all Voice cards, the DISPLAYED Tx and Rx Levels will have the following Offsets: - 2 Wires port: Tx Level: the base value (for 0dBm) = 0 Rx Level: the base value (for 0dBm) = -2 - 4 Wires port: Tx Level: the base value (for 0dBm) = -16 Rx Level: the base value (for 0dBm) = 7 The MIB and application DB will use the values without Offset.
agnCT1E1RingTable	1.3.6.1.4.1.164.3.1.2.2.10		not-accessible	Configuration of all T1/E1 Ring ML cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that does not participate in the T1/E1 Ring, will not exist in this table. A ML port that exists in this table, cannot exist at the same time in the IO Redundancy table (sysCRdnTable).
agnCT1E1RingEntry	1.3.6.1.4.1.164.3.1.2.2.10.1		not-accessible	An Entry in table agnCT1E1RingTable
I32 agnCT1E1RingCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.10.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
INT agnCT1E1RingPrimeSlot	1.3.6.1.4.1.164.3.1.2.2.10.1.2	INTEGER	read-only	The slot number of the Primary card of the Ring Pair.
I32 agnCT1E1RingPrimePort	1.3.6.1.4.1.164.3.1.2.2.10.1.3	Integer32	read-only	The port number in the Primary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104
INT agnCT1E1RingSecSlot	1.3.6.1.4.1.164.3.1.2.2.10.1.4	INTEGER	read-create	The slot number of the Secondary card of the Ring Pair.
I32 agnCT1E1RingSecPort	1.3.6.1.4.1.164.3.1.2.2.10.1.5	Integer32	read-create	The port number in the Secondary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104
I32 agnCT1E1RingRecTime	1.3.6.1.4.1.164.3.1.2.2.10.1.6	Integer32	read-create	T1/E1 Ring Recovery Time (sec). Valid Values: 1..99, 65535. 65535=NA.
ROW agnCT1E1RingRowStatus	1.3.6.1.4.1.164.3.1.2.2.10.1.7	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table. The only possible supported RowStatus vaules are active (1) and destroy (6).
U32 agnCT1E1RingWTR	1.3.6.1.4.1.164.3.1.2.2.10.1.8	Unsigned32	read-create	T1/E1 Ring Wait to Restore (sec). Valid Values: 0..999, 65535. 65535=NA. When the value <> 65535, the value of agnCT1E1RingRecTime must be 65535.
INT agnCT1E1RingDualFailDetection	1.3.6.1.4.1.164.3.1.2.2.10.1.9	INTEGER	read-create	T1/E1 Ring - Dual Failure Detection enable/disable.
INT agnCMainExitPort	1.3.6.1.4.1.164.3.1.2.2.11	INTEGER	read-write	An object defining the Main Exit Port for the Data of the device. In the Vmux-120 Device the Data can Exit via one of the 2 existing ports: 1. Ethernet port (2) 2. A port that can be E1 or T1 or a Serial Link (3).
agnCBuMlTable	1.3.6.1.4.1.164.3.1.2.2.12		not-accessible	Configuration for Primary, Secondary and Third Link. These are used for Link Backup.
agnCBuMlEntry	1.3.6.1.4.1.164.3.1.2.2.12.1		not-accessible	An Entry in table agnCBuMlTable
I32 agnCBuMlCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.12.1.1	Integer32	not-accessible	This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.
INT agnCBuMlRole	1.3.6.1.4.1.164.3.1.2.2.12.1.2	INTEGER	not-accessible	The Role of the Link. Primary Link is the Link that should usually work. If the Primary Link fails, the data will go through the Secondary Link. If both Primary and Secondary Links fail, the data will go through the Third Link, provided it is up.
INT agnCBuMlType	1.3.6.1.4.1.164.3.1.2.2.12.1.3	INTEGER	read-write	The Type of the Link. For E1/T1 the Link can be Link A - e1T1a or Link B - e1T1b.
IP agnCBuMlDefaultGateway	1.3.6.1.4.1.164.3.1.2.2.12.1.4	IpAddress	read-write	Default Gateway's IP Address.
IP agnCBuMlSubnetMask	1.3.6.1.4.1.164.3.1.2.2.12.1.5	IpAddress	read-write	The Link subnet mask.
I32 agnCBuMlOamFrequency	1.3.6.1.4.1.164.3.1.2.2.12.1.6	Integer32	read-write	Time in sec. between 2 OAM packets.
I32 agnCBuMlOamTimeoutCycles	1.3.6.1.4.1.164.3.1.2.2.12.1.7	Integer32	read-write	No. of cycles the Link will send OAM packets without receiving a response from the remote Link before switching to the Backup Link.
U32 agnCBuMlWaitToRestore	1.3.6.1.4.1.164.3.1.2.2.12.1.8	Unsigned32	read-write	This object defines traffic recovery time (in milliseconds) of the link after its recovery. This object is applicable only when Recovery Mode is revertive.
agnCQ50Table	1.3.6.1.4.1.164.3.1.2.2.13		not-accessible	Table for the device Q50 parameters. Q50 is a Signaling protocol used between PBX devices. It is possible to control the initiation of calls using Q.50. This is useful for devices when there is a congestion.
agnCQ50Entry	1.3.6.1.4.1.164.3.1.2.2.13.1		not-accessible	An Entry in table agnCQ50Table
I32 agnCQ50CnfgIdx	1.3.6.1.4.1.164.3.1.2.2.13.1.1	Integer32	not-accessible	This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.
I32 agnCQ50StopCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.2	Integer32	read-write	This object indicates the Bandwidth Threshold percent (%) above which new Calls from the PBX will be disabled.
I32 agnCQ50DiscardPktThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.3	Integer32	read-write	This object indicates the Bandwidth Threshold percent (%) above which voice packets will be discarded. Usually, the value selected should be higher than the value of agnCQ50StopCallsThresh.
I32 agnCQ50BlockNewModemVbdCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.4	Integer32	read-write	This object indicates the Modem VBD Calls Threshold percent (%) above which new modem calls will be rejected.
I32 agnCQ50BlockNewModemRelayCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.5	Integer32	read-write	This object indicates the Modem Relay Calls Threshold percent (%) above which new modem calls will be rejected.
cmprAgnGen	1.3.6.1.4.1.164.3.1.2.3
agnCmprTable	1.3.6.1.4.1.164.3.1.2.3.1		not-accessible	A table.
agnCmprEntry	1.3.6.1.4.1.164.3.1.2.3.1.1		not-accessible	An entry in table.
I32 agnCmprTypIdx	1.3.6.1.4.1.164.3.1.2.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 agnCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 agnCmprVersion	1.3.6.1.4.1.164.3.1.2.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
OCT agnCmprObj	1.3.6.1.4.1.164.3.1.2.3.1.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
agnDlciCmprTable	1.3.6.1.4.1.164.3.1.2.3.2		not-accessible	A table.
agnDlciCmprEntry	1.3.6.1.4.1.164.3.1.2.3.2.1		not-accessible	An entry in table.
I32 agnDlciCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.2.1.1	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 agnDlciCmprVersion	1.3.6.1.4.1.164.3.1.2.3.2.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnDlciCmprDlciIdx	1.3.6.1.4.1.164.3.1.2.3.2.1.3	Integer32	read-only	This attribute indicates a unique identifier of the Dlci, the compressed information relates to. The values are between 16 - 991.
OCT agnDlciCmprObj	1.3.6.1.4.1.164.3.1.2.3.2.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
agnAlarmsCmprTable	1.3.6.1.4.1.164.3.1.2.3.3		not-accessible	A table.
agnAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.2.3.3.1		not-accessible	An entry in table.
I32 agnAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.2.3.3.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.2.3.3.1.2	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
OCT agnAlarmsCmprObj	1.3.6.1.4.1.164.3.1.2.3.3.1.3	OCTET STRING	read-only	This attribute is the compressed information itself.
agnAlrBufCmprTable	1.3.6.1.4.1.164.3.1.2.3.4		not-accessible	A table.
agnAlrBufCmprEntry	1.3.6.1.4.1.164.3.1.2.3.4.1		not-accessible	An entry in table.
I32 agnAlrBufCmprVersion	1.3.6.1.4.1.164.3.1.2.3.4.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnAlrBufCmprAlarmIdx	1.3.6.1.4.1.164.3.1.2.3.4.1.2	Integer32	read-only	A unique number to identify an entry in the history alarms buffer of the agent.
OCT agnAlrBufCmprObj	1.3.6.1.4.1.164.3.1.2.3.4.1.3	OCTET STRING	read-only	This attribute is the compressed information itself.
agnSCmprErrListTable	1.3.6.1.4.1.164.3.1.2.3.5		not-accessible	A table.
agnSCmprErrListEntry	1.3.6.1.4.1.164.3.1.2.3.5.1		not-accessible	An entry in table.
I32 agnSCmprErrVersion	1.3.6.1.4.1.164.3.1.2.3.5.1.1	Integer32	read-only	The version of the compressed data
I32 agnSCmprErrIdx	1.3.6.1.4.1.164.3.1.2.3.5.1.2	Integer32	read-only	Unique number to identify an entry in the errors list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'.
OCT agnSCmprErrObj	1.3.6.1.4.1.164.3.1.2.3.5.1.3	OCTET STRING	read-only	This attribute is a full text description of the error, including: error code, slot and port numbers related to the code .
agnTsCmprTable	1.3.6.1.4.1.164.3.1.2.3.6		not-accessible	A table.
agnTsCmprEntry	1.3.6.1.4.1.164.3.1.2.3.6.1		not-accessible	An entry in table.
I32 agnTsCmprVerIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.1	Integer32	read-only	This object indicates the version of the internal format of the Compressed data.
I32 agnTsCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.2	Integer32	read-only	This object indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration.
I32 agnTsCmprSlotIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.3	Integer32	read-only	This object indicates the Slot to which the Compressed information is related. For MP-2100: IO-1..IO-12 = (5).. (16) For DXC-30 : IO-1..IO-15 = (5).. (19). NA=255.
I32 agnTsCmprPortIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.4	Integer32	read-only	This object indicates the Port within the Slot, to which the Compressed information is related. For Port Index see each product's spec.
I32 agnTsCmprPduIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.5	Integer32	read-only	This object indicates the PDU index within the same port. That provides for the case when one PDU is not sufficient for all TS Assignment data of the same port.
OCT agnTsCmprData	1.3.6.1.4.1.164.3.1.2.3.6.1.6	OCTET STRING	read-write	This object is the compressed information itself. It provides information about all TSs of a port.
agnXCmprTable	1.3.6.1.4.1.164.3.1.2.3.7		not-accessible	A table.
agnXCmprEntry	1.3.6.1.4.1.164.3.1.2.3.7.1		not-accessible	An entry in table.
I32 agnXCmprTypIdx	1.3.6.1.4.1.164.3.1.2.3.7.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred. One of the types is V5.1 Variant data.
I32 agnXCmprVersion	1.3.6.1.4.1.164.3.1.2.3.7.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data.
I32 agnXCmprIdx3	1.3.6.1.4.1.164.3.1.2.3.7.1.3	Integer32	read-only	3rd index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant, this attribute indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration.
I32 agnXCmprIdx4	1.3.6.1.4.1.164.3.1.2.3.7.1.4	Integer32	read-only	4th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique number of the slot position where the card is inserted. Valid values: psA(1),psB(2),clA(3),clB(4),io1(5)..io12(16); notApplicable=255.
I32 agnXCmprIdx5	1.3.6.1.4.1.164.3.1.2.3.7.1.5	Integer32	read-only	5th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt12 (12) , inPrt1 (101) .. inPrt48 (148).
I32 agnXCmprIdx6	1.3.6.1.4.1.164.3.1.2.3.7.1.6	Integer32	read-only	6th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates the Variant index. Valid values are: 0..127, 255 (= temp cnfg).Set can be performed only to the temporary configuration.
I32 agnXCmprIdx7	1.3.6.1.4.1.164.3.1.2.3.7.1.7	Integer32	read-only	7th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute is not needed. Therefore, its value will be always 255=notApplicable.
OCT agnXCmprObj	1.3.6.1.4.1.164.3.1.2.3.7.1.8	OCTET STRING	read-write	This attribute is the compressed information itself.
alrBuffGen	1.3.6.1.4.1.164.3.1.2.4
alrBufTable	1.3.6.1.4.1.164.3.1.2.4.1		not-accessible	A table.
alrBufEntry	1.3.6.1.4.1.164.3.1.2.4.1.1		not-accessible	An entry in table.
I32 alrBufIdx	1.3.6.1.4.1.164.3.1.2.4.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify this entry
STR alrBufDescription	1.3.6.1.4.1.164.3.1.2.4.1.1.2	DisplayString	read-only	This entry is a unique text description of the alarm in the buffer. The alarm description includes the following information: alarm code, slot id, card type, channel id , alarm text, alarm status, masked flag and event counter
U32 alrBufCode	1.3.6.1.4.1.164.3.1.2.4.1.1.3	Unsigned32	read-only	A code identifying the alarm of an entry in the alarm buffer table.
INT alrBufSlot	1.3.6.1.4.1.164.3.1.2.4.1.1.4	INTEGER	read-only	The slot number this alarm refers to. When the alarm refers to a system alarm, the value will be 'notApplicable(255)'.
U32 alrBufPort	1.3.6.1.4.1.164.3.1.2.4.1.1.5	Unsigned32	read-only	The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999.
INT alrBufSeverity	1.3.6.1.4.1.164.3.1.2.4.1.1.6	INTEGER	read-only	The severity of the alarm.
INT alrBufState	1.3.6.1.4.1.164.3.1.2.4.1.1.7	INTEGER	read-only	State of the alarm (On/Off).
INT alrBufferClearCmd	1.3.6.1.4.1.164.3.1.2.4.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2). For MP-2100/2200, this command will not really erase the Alarm Buffer, but is only an ACK of seeing the Buffer. It marks a pointer of the last entry's alrBufIdx, in order to allow view of new alarms entered after this pointer (alrBufIdxUponLastAck).
U32 alrBufIdxUponLastAck	1.3.6.1.4.1.164.3.1.2.4.3	Unsigned32	read-only	This attribute indicates the value of alrBufIdx for the last existing entry of alrBufTable, when alrBufferClearCmd was last Set to on(3). That will enable a user to see only Alarms that entered the alrBufTable after last Set of alrBufferClearCmd, by GetNext of alrBufDescription with this index.
agnFlipDb	1.3.6.1.4.1.164.3.1.2.5
agnCAgendaTable	1.3.6.1.4.1.164.3.1.2.5.1		not-accessible	This table devides the week days into categories needed for DB flip consideration.
agnCAgendaEntry	1.3.6.1.4.1.164.3.1.2.5.1.1		not-accessible	An entry in table.
INT agnCAgendaCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.1.1.1	INTEGER	read-only	Active or Temporary Agenda Table. Both configurations can be read but only the Temporary can be written to.
INT agnCAgendaDayIdx	1.3.6.1.4.1.164.3.1.2.5.1.1.2	INTEGER	read-only	Day of week
INT agnCAgendaDayCategory	1.3.6.1.4.1.164.3.1.2.5.1.1.3	INTEGER	read-write	The Category of the Day
agnCFlipNetEventsTable	1.3.6.1.4.1.164.3.1.2.5.2		not-accessible	This table holds the Net Events the MUX should trace
agnCFlipNetEventsEntry	1.3.6.1.4.1.164.3.1.2.5.2.1		not-accessible	An entry in table.
INT agnCFlipNetEventsCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.2.1.1	INTEGER	read-only	Active or Temporary Net Events Table. Both configurations can be read but only the Temporary can be written to.
I32 agnCFlipNetEventIdx	1.3.6.1.4.1.164.3.1.2.5.2.1.2	Integer32	read-only	Entry within the table
INT agnCFlipNetEventActive	1.3.6.1.4.1.164.3.1.2.5.2.1.3	INTEGER	read-write	Indicates if the entry is valid. In order to Add/Modify parameters of an entry, this object should be set to Yes. In order to delete an entry, this object should be Set to No.
INT agnCFlipNetEventType	1.3.6.1.4.1.164.3.1.2.5.2.1.4	INTEGER	read-write	The Net Event type
I32 agnCFlipNetEventNo	1.3.6.1.4.1.164.3.1.2.5.2.1.5	Integer32	read-write	The Net Event No. (Bit Index)
INT agnCFlipNetEventSlot	1.3.6.1.4.1.164.3.1.2.5.2.1.6	INTEGER	read-write	The slot to which the net event relates . Not applicable for time event
I32 agnCFlipNetEventPort	1.3.6.1.4.1.164.3.1.2.5.2.1.7	Integer32	read-write	The port within the relevant slot. Valid values: - extPrt1(1)..exPrt16(16) - notApplicable(100) - inPrt1(101)..inPrt84(184)
I32 agnCFlipNetEventISD	1.3.6.1.4.1.164.3.1.2.5.2.1.8	Integer32	read-write	The time in seconds since the Net Event was reported as ON until it is considered as ON. Not relevant for time events.
I32 agnCFlipNetEventOSD	1.3.6.1.4.1.164.3.1.2.5.2.1.9	Integer32	read-write	The time in seconds since the net event was reported as OFF until it is considered as OFF. Not relevant for time events.
INT agnCFlipNetEventDayType	1.3.6.1.4.1.164.3.1.2.5.2.1.10	INTEGER	read-write	The time event relates to all days defined in this category in the agnCAgendaTable. Applicable only for time event
STR agnCFlipNetEventStartTime	1.3.6.1.4.1.164.3.1.2.5.2.1.11	DisplayString	read-write	The time event will be activated at this time. The format is hh:mm.
STR agnCFlipNetEventEndTime	1.3.6.1.4.1.164.3.1.2.5.2.1.12	DisplayString	read-write	The time event will be deactivated at this time. The format is hh:mm.
agnCFlipTable	1.3.6.1.4.1.164.3.1.2.5.3		not-accessible	The DB Flip Decisions Table
agnCFlipEntry	1.3.6.1.4.1.164.3.1.2.5.3.1		not-accessible	An entry in table.
INT agnCFlipCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.3.1.1	INTEGER	read-only	Active or Temporary Flip Decisions Table. Both configurations can be read but only the Temporary can be written to.
I32 agnCFlipIdx	1.3.6.1.4.1.164.3.1.2.5.3.1.2	Integer32	read-only	Entry number within the table
INT agnCFlipActive	1.3.6.1.4.1.164.3.1.2.5.3.1.3	INTEGER	read-write	Indicates if the entry is valid. In order to Add/Modify parameters of an entry this object should be Set to Yes. In order to delete an entry, this object should be Set to No.
STR agnCFlipLogicalExp	1.3.6.1.4.1.164.3.1.2.5.3.1.4	DisplayString	read-write	A logical expression composed of events numbers (which were configured in the 'AgnCFlipNetEvantsTable') and logical operators ('\|', '&', '!', '(', ')') between them. e.g - (1 & !2) \| (121 & 230)
I32 agnCFlipDbNo	1.3.6.1.4.1.164.3.1.2.5.3.1.5	Integer32	read-write	The ID of the required DB
INT agnCFlipDiscardDe	1.3.6.1.4.1.164.3.1.2.5.3.1.6	INTEGER	read-write	Indicates whether the Mux should start discarding all DE. (MP3000 Only).
agnFlipDbControls	1.3.6.1.4.1.164.3.1.2.5.4
INT agnCFlipDbSanityCheckCmd	1.3.6.1.4.1.164.3.1.2.5.4.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and automatically be changed to off(2).
INT agnCSaveFlipDbCmd	1.3.6.1.4.1.164.3.1.2.5.4.2	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and if it is OK, it will save the Flip Db in the NVRAM, activating the new Flip DB . If check detects errors, the save will not be performed. Afterwards, the object's value will change automatically to off(2).
I32 agnCSaveNetCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.5.4.3	Integer32	read-write	This attribute specifies the Id of the target NVRAM Cnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown. This attribute doesn't cause actual Flip.
INT agnCSaveNetFlipDbCmd	1.3.6.1.4.1.164.3.1.2.5.4.4	INTEGER	read-write	Setting this attribute to on(3) will save the Temp Flip DB Into the NVRAM without actual flip.
INT agnCNetGoCmd	1.3.6.1.4.1.164.3.1.2.5.4.5	INTEGER	read-write	Setting this attribute to On will broadcast a 'GO' command to the network. When a Mux receives a 'GO' command it issues a delay for 'agnCNetDelay' seconds and then activates the DB which was pre-defined by one of the commands : 'agnCSaveNetCnfgIdxCmd' or 'agnCSaveNetFlipDbCmd'.
I32 agnCNetDelay	1.3.6.1.4.1.164.3.1.2.5.4.6	Integer32	read-write	This attribute determines the period of time in seconds that takes for a message to be transferred over all the network. After a 'GO' command the MUX issues a delay of 'agnCNetDelay' before activating the appropriate DB. The delay will be applied only after performing agnCSaveFlipDbCmd.
INT agnCNetEventsBcast	1.3.6.1.4.1.164.3.1.2.5.4.7	INTEGER	read-write	This object determines if the Net Events will be Broadcasted to other Muxes of the Net or not. disabled - Net Events will NOT be Broadcasted enabled - Net Events will be Broadcasted. Default=disabled. The value will be applied only after performing agnCSaveFlipDbCmd.
I32 agnCNetEventsBcastInterval	1.3.6.1.4.1.164.3.1.2.5.4.8	Integer32	read-write	When agnCNetEventsBcast is enabled, this object determines the interval of time in seconds, between two consecutive Net Events transferred over the network. Default=40 sec. The interval will be applied only after performing agnCSaveFlipDbCmd.
agnSa	1.3.6.1.4.1.164.3.1.2.6
I32 agnSaSwchStatus	1.3.6.1.4.1.164.3.1.2.6.1	Integer32	read-only	This object indicates the status of the switches on the stand-alone unit. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits: bit 0 NMS (LSB) bit 1 Terminal '1' = forces the DCE to be terminal with Rate=9600bps, Data bits=8, Stop bits=1 bit 2 Xray bit 3 SW-Load '1' = when SW is loaded bit 4 DBS Default of all bits=0 When the status of these switches is unknown, the value of this object is 255.
agnListDecoding	1.3.6.1.4.1.164.3.1.2.7
agnListDecodingTable	1.3.6.1.4.1.164.3.1.2.7.1		not-accessible	A decoding table . For each type of list, a description is given for each existing code.
agnListDecodingEntry	1.3.6.1.4.1.164.3.1.2.7.1.1		not-accessible	An entry in table.
INT agnListDecodingType	1.3.6.1.4.1.164.3.1.2.7.1.1.1	INTEGER	read-only	The type of list the decoding data refers to. alr - Alarms list sanity - Sanity Check Error list. counter - Counter type of ifPerfCounterType
I32 agnListDecodingCode	1.3.6.1.4.1.164.3.1.2.7.1.1.2	Integer32	read-only	The specific code for which decoding is needed.
STR agnListDecodingDescription	1.3.6.1.4.1.164.3.1.2.7.1.1.3	DisplayString	read-only	The description fitting the specific code and type of list required.
INT agnListDecodingDefState	1.3.6.1.4.1.164.3.1.2.7.1.1.4	INTEGER	read-only	This object is applicable only for agnListDecodingType=alr. It reports the default state/severity of each alarm. User can change the severity of the alarms defined by this default via the agnListDecodingSeverity object.
INT agnListDecodingSeverity	1.3.6.1.4.1.164.3.1.2.7.1.1.5	INTEGER	read-write	This object is applicable only for agnListDecodingType=alr. It enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code). event - can be set only for an alarm that is defined by default as 'event'. User can change the severity of the alarms defined by default as minor or major. The severity of an event may be set to another severity, but the change will actually happen only if the event threshold is active and passed the Set/ON condition. An event alarm that passed the threshold and changed its severity, will return automatically to event severity when meeting its Reset/OFF condition.
INT agnListDecodingAcmRelaySlt	1.3.6.1.4.1.164.3.1.2.7.1.1.6	INTEGER	read-write	This object indicates the ACM slot, desired for outbound relay (report) for the selected alarm. In the ?004 Unit the entries io6(10)..io12(16) are not valid. none - when agnListDecodingType=alr AND the selected alarm should not be reported by an ACM card. notApplicable - when agnListDecodingType=sanity OR when [agnListDecodingType=alr and there is no ACM card installed in the Mux].
INT agnListDecodingAcmRelayPrt	1.3.6.1.4.1.164.3.1.2.7.1.1.7	INTEGER	read-write	This object indicates the ACM port within the slot, desired for outbound relay (report) for the selected alarm. notApplicable - when agnListDecodingType=sanity OR when agnListDecodingAcmRelaySlt=notApplicable.
agnSystemDlci	1.3.6.1.4.1.164.3.1.2.8
agnDlciTable	1.3.6.1.4.1.164.3.1.2.8.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
agnDlciEntry	1.3.6.1.4.1.164.3.1.2.8.1.1		not-accessible	An entry in table.
I32 agnDlciCnfgIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT agnDlciLSltIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. This is the Source Slot of the DLCI. vs=Voice Switching In the ?004 Unit the entries io6(10)..io16) are not valid. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) LSlotIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
I32 agnDlciLPrtIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.3	Integer32	read-only	This attribute indicates a unique external or internal port number, including linkSelector or encapsulator. This is the Source Port of the DLCI. 100=noConnect (for voice switching) LPrtIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
I32 agnDlciLIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used DLCI(16..991). This is the Source Side of the DLCI. 0=notApplicable (for voice switching) LIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
INT agnDlciHSltIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.5	INTEGER	read-only	This attribute indicates a unique slot position In the Mux where the DLCI is routed to - Destination Slot. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io16) are not valid
I32 agnDlciHPrtIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.6	Integer32	read-only	This attribute indicates a unique port number where the DLCI is routed to - Destination Port.
I32 agnDlciHIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.7	Integer32	read-only	This attribute indicates a unique internal connection DLCI number where the Source DLCI is routed to - the Destination Side of the DLCI.
INT agnDlciTxBc	1.3.6.1.4.1.164.3.1.2.8.1.1.8	INTEGER	read-create	This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line.
INT agnDlciTxBe	1.3.6.1.4.1.164.3.1.2.8.1.1.9	INTEGER	read-create	This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line.
INT agnDlciRxBc	1.3.6.1.4.1.164.3.1.2.8.1.1.10	INTEGER	read-create	This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line.
INT agnDlciRxBe	1.3.6.1.4.1.164.3.1.2.8.1.1.11	INTEGER	read-create	This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line.
I32 agnDlciPriority	1.3.6.1.4.1.164.3.1.2.8.1.1.12	Integer32	read-create	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 7 is the highest priority.
INT agnDlciStatus	1.3.6.1.4.1.164.3.1.2.8.1.1.13	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
INT agnDlciSpoofing	1.3.6.1.4.1.164.3.1.2.8.1.1.14	INTEGER	read-create	This object refers to sending of RIP messages: - yes : RIP messages will be sent ONLY if there is a change in the Net. - no : RIP messages will be always sent. This object is relevant only when one side of the DLCI is a CL-NMS interface. Default=no.
INT agnDlciFunnelEnable	1.3.6.1.4.1.164.3.1.2.8.1.1.15	INTEGER	read-create	This object selects Funnel activation: - disabled: Funnel operation will be disabled. The agnDlciTxBe and agnDlciTxBc values are not used for funneling. - enabled : Funnel operation will be enabled both for Source and Destination of the DLCI. The agnDlciTxBe and agnDlciTxBc values are used for funneling calculations. - source: Funnel operation will be enabled only for the Source of the DLCI. - destination:Funnel operation will be enabled only for the Destination of the DLCI. This object is relevant only for an encapsulating DLCI. In case of a Link Selector DLCI, the agnDlciTxBe and agnDlciTxBc values are used for bandwidth of Link Selector. Default=disabled.
INT agnDlciRoutingProtocol	1.3.6.1.4.1.164.3.1.2.8.1.1.16	INTEGER	read-create	This object is relevant only when one side of the DLCI is a CL-NMS interface. It defines which Routing Protocol will be used for management via CL-NMS port. notApplicable will be used for all slots but CL. rip is a proprietary rip protocol. Default=rip.
ROW agnDlciRowStatus	1.3.6.1.4.1.164.3.1.2.8.1.1.17	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set agnRowStatus.255.id2.id3.id4.id5.id6.id7 = active(1). For destroying a row, the NMS should set: agnRowStatus.255.id2.id3.id4.id5.id6.id7 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
agnVoiceSwitching	1.3.6.1.4.1.164.3.1.2.9
agnVoiceSwConfTable	1.3.6.1.4.1.164.3.1.2.9.1		not-accessible	MXcess Configuration for Voice Switching.
agnVoiceSwConfEntry	1.3.6.1.4.1.164.3.1.2.9.1.1		not-accessible	An entry in table.
INT agnVoiceSwConfIdx	1.3.6.1.4.1.164.3.1.2.9.1.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
STR agnVoiceSwConfZoneId	1.3.6.1.4.1.164.3.1.2.9.1.1.2	DisplayString	read-write	1 or 2 digits, (0-9)(1-9).
STR agnVoiceSwConfNodeId	1.3.6.1.4.1.164.3.1.2.9.1.1.3	DisplayString	read-write	1, 2 or 3 digits, (1-9),(0-9),(0-9).
I32 agnVoiceSwConfNoOfHops	1.3.6.1.4.1.164.3.1.2.9.1.1.4	Integer32	read-write	Number of hops the frame will go through the net before deciding to discard the frame (like time-to-live in IP). 0 = notApplicable Default=20 .
I32 agnVoiceSwConfSidt	1.3.6.1.4.1.164.3.1.2.9.1.1.5	Integer32	read-write	SIDT: Short Inter Digit Timeout used as timer (in sec.) between digits after routing is completed. The timeout indicates end of dialing and the call can then be setup. 0 = notApplicable Default=2 sec.
I32 agnVoiceSwConfLidt	1.3.6.1.4.1.164.3.1.2.9.1.1.6	Integer32	read-write	LIDT: Long Inter Digit Timeout used as timer between digits before routing is completed. If no digits were dialed and LIDT expired then the user will get an error tone and the call will be disconnected. 0 = notApplicable Default=15 sec.
INT agnVoiceSwConfDialPlan	1.3.6.1.4.1.164.3.1.2.9.1.1.7	INTEGER	read-write	This is the Dialing Plan method that will be used in the Voice Switching. Static Dialing Plan - Routing is defined by the current device Zone and Node ID in the Network. Static Dialing Plan Plus - Includes the Static Dialing Plan but contains an addition of defining the number of dialed digits. Flexible Dialing Plan - Routing is defined in a flexible form. In this plan the user can configure the extension number of a local voice channel, Route a call to a remote destination and enter the Number of Digits for a specific dial prefix.
agnVoiceSwConfRtTable	1.3.6.1.4.1.164.3.1.2.9.2		not-accessible	Routing Table for Voice Switching.
agnVoiceSwConfRtEntry	1.3.6.1.4.1.164.3.1.2.9.2.1		not-accessible	An entry in table.
INT agnVoiceSwConfRtDbId	1.3.6.1.4.1.164.3.1.2.9.2.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
I32 agnVoiceSwConfRtIdx	1.3.6.1.4.1.164.3.1.2.9.2.1.2	Integer32	read-only	The Index of the row.
STR agnVoiceSwConfRtDigits	1.3.6.1.4.1.164.3.1.2.9.2.1.3	DisplayString	read-create	Dialed digits: Series of digits 0...9, '', '#' or '%'. The '' and '#' can have many uses according to the user's decision. For example, they can be used as part of the Dialed Number, they exist on the phone number panel. '*' can also be used instead of a series of numbers. The '%' means any digits (wildcard) and is used without a series of digits. When the agnVoiceSwConfRtAction is del (7), the series of digits that are configured via this MIB object will be deleted from the prefix of the dialed number.
INT agnVoiceSwConfRtAction	1.3.6.1.4.1.164.3.1.2.9.2.1.4	INTEGER	read-create	Action that the system should perform for the digits: agnVoiceSwConfRtDigits. The action that is allowed depends on the Dialing Plan. Here is the list of the allowed actions: For Static Dialing Plan - zone, node, in, shortDialing, hgr, del, rep For Static Dialing Plan Plus - zone, node, in, shortDialing, hgr, del, rep, numDigDP For Flexible Dialing Plan - hgr, del, rep, numDigDP, route, ext
STR agnVoiceSwConfRtData	1.3.6.1.4.1.164.3.1.2.9.2.1.5	DisplayString	read-create	This field is relevant for actions hgr(6), and rep(8), numDigDP(11) and contains the following information: For hgr - the number of the Hunt Group. For rep - the number of digits to be replaced with. For numDigDP - the number of digits collected before establishing the call. 0 indicates no defined length. In this case SIDT will be used.
INT agnVoiceSwConfRtSlot	1.3.6.1.4.1.164.3.1.2.9.2.1.6	INTEGER	read-create	Routing Slot- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13).
I32 agnVoiceSwConfRtPort	1.3.6.1.4.1.164.3.1.2.9.2.1.7	Integer32	read-create	Routing Port- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). 100=noConnect (for non-routing case).
I32 agnVoiceSwConfRtDlci	1.3.6.1.4.1.164.3.1.2.9.2.1.8	Integer32	read-create	Routing DLCI- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). Valid values: 0=notApplicable (for non-routing case). 1, 16..991
ROW agnVoiceSwConfRtRowStatus	1.3.6.1.4.1.164.3.1.2.9.2.1.9	RowStatus	read-create	Status of the row for creating/deleting entries in the table. The only possible supported RowStatus vaules are active (1), notInService (2), notReady(3), createAndGo(4), createAndWait(5) and destroy(6).
I32 agnVoiceSwConfRtMaxCalls	1.3.6.1.4.1.164.3.1.2.9.2.1.10	Integer32	read-create	Maximum no. of simultaneous voice calls that are allowed in the direction defined by the current entry. Default=0 (No Limit).
I32 agnVoiceSwConfRtPriority	1.3.6.1.4.1.164.3.1.2.9.2.1.11	Integer32	read-create	This attribute indicates a unique priority of the Voice Switching Route. 1 is the lowest priority and 7 is the highest priority. 0 means N/A
agnVoiceSwConfHGTable	1.3.6.1.4.1.164.3.1.2.9.5		not-accessible	Table of Hunt Groups.
agnVoiceSwConfHGEntry	1.3.6.1.4.1.164.3.1.2.9.5.1		not-accessible	An entry in table.
INT agnVoiceSwConfHGdbIdx	1.3.6.1.4.1.164.3.1.2.9.5.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
I32 agnVoiceSwConfHGIdx	1.3.6.1.4.1.164.3.1.2.9.5.1.2	Integer32	read-only	For Vmux-300 devices - This object represents a combination of - Hunt Group number and Extension number OR - Port number and Extension number. For other devices (e.g. MXcess, MP-2100H) - There may be up to 10 Hunt Groups per MXcess. That's the index of the hunt group relevant to this row.
INT agnVoiceSwConfHGConnect	1.3.6.1.4.1.164.3.1.2.9.5.1.3	INTEGER	read-write	This attribute indicates whether the hunt group should be considered in any of the mux algorithms.
I32 agnVoiceSwConfHGExt	1.3.6.1.4.1.164.3.1.2.9.5.1.4	Integer32	read-write	This is the extension number of the hunt group. 0 is for not valid. The allowed range is 10 - 99.
STR agnVoiceSwConfHGExtString	1.3.6.1.4.1.164.3.1.2.9.5.1.5	SnmpAdminString	read-write	This is the extension string of the hunt group. This string is a combination of digits, * and #.
STR agnVoiceSwConfHGUserParams	1.3.6.1.4.1.164.3.1.2.9.5.1.6	SnmpAdminString	read-write	This object indicates the User's parameters.
INT agnVoiceSwConfHGStatus	1.3.6.1.4.1.164.3.1.2.9.5.1.7	INTEGER	read-write	This object enables the user to create/delete entries in this table. Its usage for values (1)..(6) should be identical to RowStatus SYNTAX. notApplicable(255) - should be used when the table is static (i.e. whenever create/delete entries is not allowed).
agnSigProfile	1.3.6.1.4.1.164.3.1.2.10
agnSigProfileTable	1.3.6.1.4.1.164.3.1.2.10.1		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to agnSigProfileCnfgIdx=1. The table includes signaling profile parameters for Legacy Profiles.
agnSigProfileEntry	1.3.6.1.4.1.164.3.1.2.10.1.1		not-accessible	An entry in table.
I32 agnSigProfileCnfgIdx	1.3.6.1.4.1.164.3.1.2.10.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. For products supporting more than one configuration,the write operation is valid only to the TmpCnfg. For Gmux2000 the range limitation (1..255) was discarded since the Idx is computed as: x 1000 + 255.
I32 agnSigProfileIdx	1.3.6.1.4.1.164.3.1.2.10.1.1.2	Integer32	read-only	This attribute indicates the Signaling Profile (1..5). For MP-104/204, only Profile=1 will exist.
INT agnSigProfileRxTx	1.3.6.1.4.1.164.3.1.2.10.1.1.3	INTEGER	read-only	This attribute indicates if the following objects refer to: Rx or Tx translation. Rx : ML->IO Tx : IO->ML . For MP-104/204, that means: Rx : Signaling to FXS CH Tx : Signaling to E1 Link.
OCT agnSigProfileABCD	1.3.6.1.4.1.164.3.1.2.10.1.1.4	OCTET STRING	read-write	For MP-2100/MP-2200 and for MP-104/204 from R2: This object represents 6 parameters, by 3 Octets : Busy Code-MSB nibble, - applicable only for Rx translation Idle Code- nibble, - applicable only for Rx translation D Bit Code- nibble, C Bit Code- nibble, B Bit Code- nibble, A Bit Code-LSB nibble. Each of Busy and Idle Code nibble will have the valid values: 0000 .. FFFF. Each of A,B,C,D Bit Code nibble represents: 0 hex = 0000 = 0 1 hex = 0001 = 1 2 hex = 0010 = A bit 3 hex = 0011 = B bit 4 hex = 0100 = C bit 5 hex = 0101 = D bit 6 hex = 0110 = A bit inverse 7 hex = 0111 = B bit inverse 8 hex = 1000 = C bit inverse 9 hex = 1001 = D bit inverse A-F hex - not used (invalid values) For MP-104/204 R1: This object represents 3 parameters, by 2 Octets : Bit 1 = Bit A - OFF Hook for Tx ; Ring for Rx (LSB) Bit 2 = Bit B - OFF Hook for Tx ; Ring for Rx Bit 3 = Bit C - OFF Hook for Tx ; Ring for Rx Bit 4 = Bit D - OFF Hook for Tx ; Ring for Rx Bit 5 = Bit A - ON Hook for Tx ; Idle for Rx Bit 6 = Bit B - ON Hook for Tx ; Idle for Rx Bit 7 = Bit C - ON Hook for Tx ; Idle for Rx Bit 8 = Bit D - ON Hook for Tx ; Idle for Rx Bit 9 = Bit A - OOS State for both Tx and Rx Bit 10 = Bit B - OOS State for both Tx and Rx Bit 11 = Bit C - OOS State for both Tx and Rx Bit 12 = Bit D - OOS State for both Tx and Rx Bit 13 = Spare (always 0) Bit 14 = Spare (always 0) Bit 15 = Spare (always 0) Bit 16 = Spare (always 0) (MSB) When the object is not applicable, the Octet String will have 0 bytes.
agnSigProfTable	1.3.6.1.4.1.164.3.1.2.10.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. This is the general table of signaling profiles.
agnSigProfEntry	1.3.6.1.4.1.164.3.1.2.10.2.1		not-accessible	An entry in table.
I32 agnSigProfCnfgIdx	1.3.6.1.4.1.164.3.1.2.10.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
I32 agnSigProfIdx	1.3.6.1.4.1.164.3.1.2.10.2.1.2	Integer32	read-only	This attribute indicates the Signaling Profile (1..5).
STR agnSigProfName	1.3.6.1.4.1.164.3.1.2.10.2.1.3	DisplayString	read-write	Profile Name given by user.
INT agnSigProfType	1.3.6.1.4.1.164.3.1.2.10.2.1.4	INTEGER	read-write	Profile Type. legacy - usual signaling. The parameters for the Legacy Profiles are detailed in the agnSigProfileTable, above. r2Cas - R2 signaling. The parameters for the R2 Profiles are detailed in the r2 ProfileCnfg tables (belong to r2If).
agnSystemTs	1.3.6.1.4.1.164.3.1.2.11
systemVoice	1.3.6.1.4.1.164.3.1.2.12
systemVoiceTable	1.3.6.1.4.1.164.3.1.2.12.1		not-accessible	General Parameters for voice - system level.
systemVoiceEntry	1.3.6.1.4.1.164.3.1.2.12.1.1		not-accessible	An entry in table.
I32 systemVoiceConfIdx	1.3.6.1.4.1.164.3.1.2.12.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed - Active or Temporary Configurations. Idx 255 relates to the temporary TmpCnfg. All configurations can be read but only the Temporary can be written to.
INT systemVoiceNationalTone	1.3.6.1.4.1.164.3.1.2.12.1.1.2	INTEGER	read-write	Tone Characteristics (Amplitude, Frequency, delays etc.). These characteristics are defined according to the country.
U32 systemVoicePacketRate	1.3.6.1.4.1.164.3.1.2.12.1.1.3	Unsigned32	read-write	This object indicates the G.729 and G.711 Coders transmitted Packet Rate in milliseconds.
INT systemVoiceFaxSupport	1.3.6.1.4.1.164.3.1.2.12.1.1.4	INTEGER	read-write	This object allows the user to Disable/Enable Fax support.
INT systemVoiceFaxRate	1.3.6.1.4.1.164.3.1.2.12.1.1.5	INTEGER	read-write	This object indicates the Fax Rate limit. It is irrelevant when Fax support is NA or disabled.
INT systemVoiceModemSupport	1.3.6.1.4.1.164.3.1.2.12.1.1.6	INTEGER	read-write	This object allows the user to Disable/Enable Modem support.
INT systemVoiceCoderAndRate	1.3.6.1.4.1.164.3.1.2.12.1.1.7	INTEGER	read-write	This object indicates the Coder and Rate for the Voice Compression.
INT systemVoiceEchoCanceler	1.3.6.1.4.1.164.3.1.2.12.1.1.8	INTEGER	read-write	This object indicates the Echo Canceler activation.
I32 systemVoiceTxGain	1.3.6.1.4.1.164.3.1.2.12.1.1.9	Integer32	read-write	This object indicates the Transmit Gain (volume) in dB.
INT systemVoiceDtmfRelayMethod	1.3.6.1.4.1.164.3.1.2.12.1.1.10	INTEGER	read-write	This object indicates the DTMF Relay Method that is used to transmit DTMF tones. rfc2833(1) - inband DTMF relay according to RFC-2833. sipInfo(2) - out of band DTMF relay using SIP INFO method.
U32 systemVoiceDtmfRelayRxPayloadType	1.3.6.1.4.1.164.3.1.2.12.1.1.11	Unsigned32	read-write	This object indicates the Rx Payload Type for DTMF relay RTP packets. It is relevant only when DTMF Relay Method is RFC-2833.
INT systemVoiceDtmfRelayPayloadTypeNeg	1.3.6.1.4.1.164.3.1.2.12.1.1.12	INTEGER	read-write	This object indicates whether Payload Type Negotiation is used (according to RFC-2833) or not. It is relevant only when DTMF Relay Method is RFC-2833.
U32 systemVoiceDtmfRelayTxPayloadType	1.3.6.1.4.1.164.3.1.2.12.1.1.13	Unsigned32	read-write	This object indicates the Tx Payload Type for DTMF relay RTP packets. It is relevant only when the Payload Type Negotiation is disabled.
systemVoiceCoderTable	1.3.6.1.4.1.164.3.1.2.12.2		not-accessible	Voice Coders table.
systemVoiceCoderEntry	1.3.6.1.4.1.164.3.1.2.12.2.1		not-accessible	An entry in Voice Coders table.
U32 systemVoiceCoderConfIdx	1.3.6.1.4.1.164.3.1.2.12.2.1.1	Unsigned32	not-accessible	The first index of the table. This object might represent the Configuration Index (1..100) being accessed; Index=255 relates to the TmpCnfg. For devices with multiple configurations, Set is permitted to TmpCnfg(255) only. Not-Applicable = 1.
U32 systemVoiceCoderPriority	1.3.6.1.4.1.164.3.1.2.12.2.1.2	Unsigned32	not-accessible	This object indicates the Coder's Priority.
INT systemVoiceCoderCoderAndRate	1.3.6.1.4.1.164.3.1.2.12.2.1.3	INTEGER	read-write	This object indicates the Coder and Rate for the Voice Compression.
mdlWanGen	1.3.6.1.4.1.164.3.1.3
statMdlGen	1.3.6.1.4.1.164.3.1.3.1
mdlSInstTable	1.3.6.1.4.1.164.3.1.3.1.1		not-accessible	A table.
mdlSInstEntry	1.3.6.1.4.1.164.3.1.3.1.1.1		not-accessible	An entry in table.
INT mdlSInstSltIdx	1.3.6.1.4.1.164.3.1.3.1.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the mux. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
INT mdlSInstCardType	1.3.6.1.4.1.164.3.1.3.1.1.1.2	INTEGER	read-only	This attribute indicates the type of card installed in the specific slot position. Only PS cards are possible in the PS slots. Only CL cards are possible in the CL slots. Only IO cards are possible in the IO slots.
STR mdlSHwVersion	1.3.6.1.4.1.164.3.1.3.1.1.1.3	DisplayString	read-only	This attribute indicates the Hardware version of the installed card in the specific slot position.
STR mdlSSwVersion	1.3.6.1.4.1.164.3.1.3.1.1.1.4	DisplayString	read-only	This attribute indicates the Software version of the installed card in the specific slot position.
INT mdlSAlrStatus	1.3.6.1.4.1.164.3.1.3.1.1.1.5	INTEGER	read-only	Indicates the alarm state at module level, i.e. lower level (port alarms) status is not included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSAlrStatusAll	1.3.6.1.4.1.164.3.1.3.1.1.1.6	INTEGER	read-only	Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSMaskedAlrStat	1.3.6.1.4.1.164.3.1.3.1.1.1.7	INTEGER	read-only	Indicates the alarm state at module level, [i.e. lower level (port alarms) status is not included],including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSMaskedAlrStatAll	1.3.6.1.4.1.164.3.1.3.1.1.1.8	INTEGER	read-only	Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSTstStatusAll	1.3.6.1.4.1.164.3.1.3.1.1.1.9	INTEGER	read-only	This attribute will be set to on(3) when there is at least one test in progress on a channel of the card, otherwise the value will be off(2).
INT mdlSClearAlrCmd	1.3.6.1.4.1.164.3.1.3.1.1.1.10	INTEGER	read-write	Setting this command to ON, enforces a clear of all the alarms in the given slot, excluding alarms of port level. The clear operation will not be applied for masked/inverted alarms.
INT mdlSClearAllAlrCmd	1.3.6.1.4.1.164.3.1.3.1.1.1.11	INTEGER	read-write	Setting this command to ON, enforces a clear of all the alarms in the given slot, including all its ports alarms. The clear operation will not be applied for masked/inverted alarms.
I32 mdlSTemperature	1.3.6.1.4.1.164.3.1.3.1.1.1.12	Integer32	read-only	Temperature of the card, in Celsius degrees.
mdlSAlrTable	1.3.6.1.4.1.164.3.1.3.1.2		not-accessible	The list of card agent alarms ; includes also an alarm indicating existence of alarms on its ports if there are any.
mdlSAlrEntry	1.3.6.1.4.1.164.3.1.3.1.2.1		not-accessible	An entry in table.
I32 mdlSAlrIdx	1.3.6.1.4.1.164.3.1.3.1.2.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive.
INT mdlSAlrSltIdx	1.3.6.1.4.1.164.3.1.3.1.2.1.2	INTEGER	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
STR mdlSAlrCodeDescription	1.3.6.1.4.1.164.3.1.3.1.2.1.3	DisplayString	read-only	This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
I32 mdlSAlrCode	1.3.6.1.4.1.164.3.1.3.1.2.1.4	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at card level.
INT mdlSAlrSeverity	1.3.6.1.4.1.164.3.1.3.1.2.1.5	INTEGER	read-only	The severity of the alarm.
INT mdlSAlrState	1.3.6.1.4.1.164.3.1.3.1.2.1.6	INTEGER	read-only	State of the alarm.
I32 mdlSAlrCounter	1.3.6.1.4.1.164.3.1.3.1.2.1.7	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
INT mdlSAlrMask	1.3.6.1.4.1.164.3.1.3.1.2.1.8	INTEGER	read-only	Alarm mask : on/off.
INT mdlSAlrInvert	1.3.6.1.4.1.164.3.1.3.1.2.1.9	INTEGER	read-only	Alarm invert : on/off.
cnfgMdlGen	1.3.6.1.4.1.164.3.1.3.2
mdlCPrgTable	1.3.6.1.4.1.164.3.1.3.2.1		not-accessible	A table.
mdlCPrgEntry	1.3.6.1.4.1.164.3.1.3.2.1.1		not-accessible	An entry in table.
I32 mdlCCnfgIdx	1.3.6.1.4.1.164.3.1.3.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..100) being referred. Value 255 specifies the TmpCnfg
INT mdlCSltIdx	1.3.6.1.4.1.164.3.1.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
INT mdlCPrgCardType	1.3.6.1.4.1.164.3.1.3.2.1.1.3	INTEGER	read-write	This attribute indicates the type of card assigned to the specific slot in the common configuration. This object is identical in all the configurations (1..100). Only the TmpCnf(255) may have different value. The write operation is valid only to the TmpCnfg entry.
I32 mdlCNoOfExternPrt	1.3.6.1.4.1.164.3.1.3.2.1.1.4	Integer32	read-only	Number of external ports in the programmed card of the specific slot position
I32 mdlCNoOfInternPrt	1.3.6.1.4.1.164.3.1.3.2.1.1.5	Integer32	read-only	Number of internal ports in the programmed card of the specific slot position.
INT mdlCWorkMode	1.3.6.1.4.1.164.3.1.3.2.1.1.6	INTEGER	read-write	Working mode of the card. The user may configure the card to work in a stand alone mode or integrated with the device. Example for use in MHS-IP cards: - standAlone - in this mode, the router works so that data is received via the LAN (Eth) port and is transmitted via the WAN (HS) external port without going through the MPH device. - integrated - in this mode, the router works so that it is integrated in the MPH and routes DLCIs into the device.
INT mdlCDhcpClientEnable	1.3.6.1.4.1.164.3.1.3.2.1.1.7	INTEGER	read-write	Enable/Disable the feature of DHCP Client for the selected card.
INT mdlCRdnExists	1.3.6.1.4.1.164.3.1.3.2.1.1.8	INTEGER	read-only	This object indicates whether any port of the programmed card is configured to be part of a Redundancy/APS pair. If at least one port of the programmed card is configured to be part of a Redundancy/APS pair, the value will be 'yes'. Otherwise, it will be 'no'.
OCT mdlCInterfaces	1.3.6.1.4.1.164.3.1.3.2.1.1.9	OCTET STRING	read-only	Octet string which indicates 'present' interfaces in card. Each '0' bit stands for non-present interface. Each '1' bit stands for present interface. For ASMi54C card of LRS-102 and MP-4100 notPresent interfaces may be: - SHDSL Line ID with no wire pairs assigned to it (does not exist in ifTable) - PCS without SHDSL Line binded to it, (exist in ifTable, with ifOperStatus= notPresent) - External DS1 when its LIU is used by an Internal DS1 of the same card - Internal DS1 when single bearer is not TDM. In each octet, MS bit represents port 1 and LS bit represents port 8 MSB LSB 1 0 0 0 1 0 0 0 -- Example: Port # 1 and 5 are present. Port 1 2 3 4 5 6 7 8 1st Octet (MSB octet) represents SDHSL Lines 2nd Octet represents PCS 3rd Octet represents External DS1 4th Octet represents Internal DS1 5th and 6th Octets are reserved for future Internal DS1. For OP-108/106 cards of LRS-102 and MP-4100 notPresent interfaces may be: - External DS1 when its 'associated' Int-DS1 port is connected to another card - Internal DS1 when its 'associated' Ext-DS1 port is connected to another card (Both may be 'present' when inter-connected). 1st Octet represents External DS1 2nd Octet represents Internal DS1 Bit representation, same as for ASMi-54C card.
cmprMdlGen	1.3.6.1.4.1.164.3.1.3.3
mdlCmprTable	1.3.6.1.4.1.164.3.1.3.3.1		not-accessible	A table.
mdlCmprEntry	1.3.6.1.4.1.164.3.1.3.3.1.1		not-accessible	An entry in table.
I32 mdlCmprTypIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 mdlCmprCnfgIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 mdlCmprVersion	1.3.6.1.4.1.164.3.1.3.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
INT mdlCmprSltIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
OCT mdlCmprObj	1.3.6.1.4.1.164.3.1.3.3.1.1.5	OCTET STRING	read-write	This attribute is the compressed information itself.
mdlAlarmsCmprTable	1.3.6.1.4.1.164.3.1.3.3.2		not-accessible	A table.
mdlAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.3.3.2.1		not-accessible	An entry in table.
I32 mdlAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.3.3.2.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 mdlAlarmsCmprAlarmSlot	1.3.6.1.4.1.164.3.1.3.3.2.1.2	Integer32	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid.
I32 mdlAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.3.3.2.1.3	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
OCT mdlAlarmsCmprObj	1.3.6.1.4.1.164.3.1.3.3.2.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
prtWanGen	1.3.6.1.4.1.164.3.1.4
statPrtGen	1.3.6.1.4.1.164.3.1.4.1
prtSInstTable	1.3.6.1.4.1.164.3.1.4.1.1		not-accessible	A table.
prtSInstEntry	1.3.6.1.4.1.164.3.1.4.1.1.1		not-accessible	An entry in table.
INT prtSInstSltIdx	1.3.6.1.4.1.164.3.1.4.1.1.1.1	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted. In the ?004 Unit the entries io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
I32 prtSInstPrtIdx	1.3.6.1.4.1.164.3.1.4.1.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port in a specific card. The valid ports depend on the installed card: the valid external ports (interfaces) are (1..mdlCNoOfExternPrt) if any, and the valid internal ports are (101..100+mdlCNoOfInternPrt) if any. Generally, for MP-2100/2200: exPrt1 (1) .. exPrt16 (16),inPrt1(101) .. inPrt48 (148) For the Vmux-2100 device: This index will have values of 1...4 for the physical ports & values of ifIndex for the bundles. For other products, see product's spec.
INT prtSInstPrtType	1.3.6.1.4.1.164.3.1.4.1.1.1.3	INTEGER	read-only	This attribute describes the type of the designated port. In MX 3000 only external & internal options are used. All the other options are only for MX 30/300 which need special handling. In order to support interface types in MX 3000, return an ascii string for prtSInterfaceType in this table or support the general RAD value of physicalConnector. External port - is a port with a physical connector. Internal port - might be of two types: a) A composite port which collects a few external ports data into a common bandwidth (usually routed through DS1 link) b) A port which gets only part of the external ports (usually a few DS0's) The following types are used when all ports are external/ internal and the connector/interface type is necessary (for example, stand-alone units): High Speed port types Low Speed port types Voice port types, CL port types. ISDN Voice in MX 30/300 Phase 4: voiceS0 (16), voiceU (17) should be used. ISDN Voice in MX 30/300 Phase 5: voiceQsigS(18), voiceQsigU (19) should be used.
I32 prtSInstIfIndex	1.3.6.1.4.1.164.3.1.4.1.1.1.4	Integer32	read-only	This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx the value will be '7fffffff'h.
INT prtSActiveStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.5	INTEGER	read-only	This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the ch is not connected according to the active config. offLine(3) indicates that the ch is down (not working) because of any problem. onLine(4) indicates that the ch is up (working) offLineRedundancy(5) indicates that the ch is down, because it is redundant port. onLineRedundancy(6) indicates that the ch is up, and it is the active link
INT prtSAlrStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.6	INTEGER	read-only	Indicates the alarm state in the port(ch) agent level. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT prtSMaskedAlrStat	1.3.6.1.4.1.164.3.1.4.1.1.1.7	INTEGER	read-only	Indicates the alarm state in the port(ch) agent level, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT prtSClearAlrCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.8	INTEGER	read-write	Setting this attribute to on(3) enforces a clear operation of the alarm status events in the given port. The clear operation will not be applied for masked/inverted alarms.
I32 prtSTestMask	1.3.6.1.4.1.164.3.1.4.1.1.1.9	Integer32	read-only	This is a mask which indicates which tests from the 'prtSTstCmd' list are allowed for the requested port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
INT prtSTstCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.10	INTEGER	read-write	Setting this attribute to any of the above values will initiate a test on the specific port if the operation is legal. If the operation is not legal, the mux will ignore the operation. testPerTS(31) - when this test is selected, the selection of tests for each TS is done via the prtExPh1MlTsTest object. If a test time out is needed, the test will be set with a default timeout of 2 minutes until the user will set the parameter 'prtSTstDuration' to the required time out. If no time out is needed , the test will be set with infinite timeout until the user will set the parameter 'prtSTstDuration' to the required time out.
I32 prtSTstDuration	1.3.6.1.4.1.164.3.1.4.1.1.1.11	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to all the test operations. The resolution will be a minute, and the maximum duration is limited to 30 minutes. For Vmux devices, the values are in seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtSTstCmd' parameter.
INT prtSBertClrCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.12	INTEGER	read-write	Setting this attribute initiates bert count clear operation. It is valid only when bert test is active on the specific port.
I32 prtSBertTstRslt	1.3.6.1.4.1.164.3.1.4.1.1.1.13	Integer32	read-only	This attribute indicates the number of Bit Error Rate indicated during the BERT operation. It is valid only when bert test is active on the specific port.
STR prtSInterfaceType	1.3.6.1.4.1.164.3.1.4.1.1.1.14	DisplayString	read-only	This attribute indicates a unique HW interface type of the selected port.
OCT prtSParamStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.15	OCTET STRING	read-only	This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For VC-6, VC-6A, VC-6AG, VC-6A/4LB, VC-12, VC-12/6, external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 \|___\| \|_______\| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|___________\| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For ACM external port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|_________\| spare Alarm State Alarm State: according to bits 1,0: 00=NA ; 01=unused ; 10=Off ; 11=On - For HS-U/1 external port - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For MTML-2/4 external ports, ML-8 externalports, ML-IP (MTML-IP) internal ports and MTML-E2 internal ports - 1 Octet : Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) - For ML-20N external ports - 4 Octets - 1 MS Octet will represent the Actual Link Rate: Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| spare Rate Valid values: 0..34, meaning: 0..32 = (0..32)x64Kbps 33 = Invalid Rate 34 = not applicable (when Rate is not Auto) 35 = 0 Kbps Invalid values: 36..255. - 2 middle Octets will represent the Status of 4 Control Signals: - LS Octet - Bits 3-0: RTS/C (Command, for X.21 interface) Bits 7-4: DCD/I (Indication for X.21 interface) - MS Octet - Bits 3-0: DTR Bits 7-4: DSR Each 4 Bits are divided as follows: - 2 MS bits: DCE - 2 LS bits: DTE For each 2 bits (DCE/DTE): 00=NA ; 01=unused ; 10=Off ; 11=On. - LS Octet: (as for MTML-2): Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) - For MP-2100/2200 MSL-4/E1, MSL-8/E1 External ports - 3 Octets - MS octet: far-end modem channel interface - Middle octet: Material (plastic/metal), far-end modem type, synchronization with far-end modem - LS octet: BERT state (at port/TS/Bit level) - MS octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) 0000 1011 = IR-ETH-QN Rest of the combinations: reserved - Middle octet: Bit 7 6 5 4 3 2 1 0 LSB \| \|___________\| \|__\| Box material modem sync Box material modem: 00000 = other sync: 00 = not sync (for ASMi-52 SA) 00001 = unknown 01 = sync 0=metal 00010 = reserved 10 = reserved 1=plastic 00011 = reserved 11 = reserved 00100 = reserved 00101 = reserved 00110 = ASMi-52 SA/2W/Slave 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD-IP 01101 = FCD-IPM 01110 = D8SL card of DXC-30 01111 = ASMi-52A 10000 = MP card (SHDSL) 10001 = ASMi-52L Rest = reserved - LS Octet: (as for MTML-2): Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs) 1 = ON (BERT is running on this port OR on one of its TSs) - For MP-4100 MSL card Links - 4 Octets - MS octet: far-end modem DTE2 interface (same as for MP-2100 MSL cards) - after MS octet: far-end modem DTE1 interface (same as for MP-2100 MSL cards) - before LS octet: Material (plastic/metal), far-end modem type, synchronization with far-end modem (same as for MP-2100 MSL cards) - LS octet: BERT state (at port/TS/Bit level)- same as for MP-2100 MSL cards - For MP-4100, LRS-102 OP-108/106 Links - 3 Octets - MS octet: far-end PS type and state - Middle octet: synchronization with far-end device - LS octet: BERT state (at port/TS level) - same as for MP-2100 MSL cards - MS octet: Bit 7 6 5 4 3 2 1 0 LSB \|__\| \|__\| \|__\| \|__\| PS-A PS-A PS-B PS-B PS Type PS State PS Type PS State 00=None 00=None 01=AC-DC 01=OK 10=DC 10=Fail - Middle octet: Bit 7 6 5 4 3 2 1 0 LSB \|__\| sync: 00 = not sync 01 = sync 10 = reserved 11 = reserved Rest = reserved
OCT prtSTestMaskXp	1.3.6.1.4.1.164.3.1.4.1.1.1.16	OCTET STRING	read-write	This is an Expanded test mask of the prtSTestMask object. The prtSTestMask object reached its maximum, being an Integer with 32 bits. This object indicates which tests from the 'prtSTstCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 csuLoopAndBert 32 dsuLoopAndBert 33 remoteOcuLoopAndBert 34 remoteCsuLoopAndBert 35 remoteDsuLoopAndBert 36 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
INT prtSRdnStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.17	INTEGER	read-only	Redundancy Status of this port. noRdn - this port is not part of a Redundancy pair/group. offline - this port is offline from Redundancy point of view. online - this port is online from Redundancy point of view.
prtSAlrTable	1.3.6.1.4.1.164.3.1.4.1.2		not-accessible	The list of port agent alarms.
prtSAlrEntry	1.3.6.1.4.1.164.3.1.4.1.2.1		not-accessible	An entry in table.
I32 prtSAlrIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive
INT prtSAlrSltIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.2	INTEGER	read-only	This attribute indicates a unique identifier of the slot where the card is inserted. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
I32 prtSAlrPrtIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.3	Integer32	read-only	This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a port which does not exist. Valid valuesfor MP-2100/2200: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148), IP Bundles. For other products, see product's spec.
STR prtSAlrCodeDescription	1.3.6.1.4.1.164.3.1.4.1.2.1.4	DisplayString	read-only	This attribute is a full text description of the alarm. The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
I32 prtSAlrCode	1.3.6.1.4.1.164.3.1.4.1.2.1.5	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at port level.
INT prtSAlrSeverity	1.3.6.1.4.1.164.3.1.4.1.2.1.6	INTEGER	read-only	The severity of the alarm.
INT prtSAlrState	1.3.6.1.4.1.164.3.1.4.1.2.1.7	INTEGER	read-only	State of the alarm.
I32 prtSAlrCounter	1.3.6.1.4.1.164.3.1.4.1.2.1.8	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
INT prtSAlrMask	1.3.6.1.4.1.164.3.1.4.1.2.1.9	INTEGER	read-only	Alarm mask : on/off.
INT prtSAlrInvert	1.3.6.1.4.1.164.3.1.4.1.2.1.10	INTEGER	read-only	Alarm invert : on/off.
INT prtSAlrCardType	1.3.6.1.4.1.164.3.1.4.1.2.1.11	INTEGER	read-only	This attribute indicates the type of card installed in the specific slot position. The enumeration is according to mdlSInstCardType.
statisPrtGen	1.3.6.1.4.1.164.3.1.4.1.3
prtFrStatis	1.3.6.1.4.1.164.3.1.4.1.3.1
prtFrStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.1.1		not-accessible	This table is applicable only for an active port running an FR protocol .
prtFrStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1		not-accessible	An entry in table.
INT prtFrStatisSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
INT prtFrStatisPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtFrStatisInvIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.3	INTEGER	read-only	The Interval of 15 min. for which the following statistics counters are applicable.
I32 prtFrTimeElapsed	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.4	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0.
C32 prtFrRxTotalFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.5	Counter32	read-only	The total number of frames received by this port during the selected interval.
C32 prtFrTxTotalFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.6	Counter32	read-only	The total number of frames sent by this port during the selected interval.
C32 prtFrRxTotalBytes	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.7	Counter32	read-only	The total number of bytes received by this port during the selected interval.
C32 prtFrTxTotalBytes	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.8	Counter32	read-only	The total number of bytes sent by this port during the selected interval.
C32 prtFrRxMngFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.9	Counter32	read-only	The management number of frames received by this port during the selected interval.
C32 prtFrTxMngFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.10	Counter32	read-only	The management number of frames sent by this port during the selected interval.
C32 prtFrRxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.11	Counter32	read-only	The number of De frames received by this port during the selected interval.
C32 prtFrTxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.12	Counter32	read-only	The number of De frames sent by this port during the selected interval.
C32 prtFrRxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.13	Counter32	read-only	The number of De frames discarded due to congestion, received by this port during the selected interval.
C32 prtFrTxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.14	Counter32	read-only	The number of De frames discarded due to congestion, sent by this port during the selected interval.
C32 prtFrRxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.15	Counter32	read-only	All the frames discarded due to congestion, received by this port during the selected interval.
C32 prtFrTxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.16	Counter32	read-only	All the frames discarded due to congestion, sent by this port during the selected interval.
C32 prtFrRxFecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.17	Counter32	read-only	Number of frames received by this port during the selected interval, indicating forward congestion.
C32 prtFrTxFecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.18	Counter32	read-only	Number of frames sent by this port during the selected interval, indicating forward congestion.
C32 prtFrRxBecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.19	Counter32	read-only	Number of frames received by this port during the selected interval, indicating backward congestion.
C32 prtFrTxBecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.20	Counter32	read-only	Number of frames sent by this port during the selected interval, indicating backward congestion.
C32 prtFrRxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.21	Counter32	read-only	Number of data frames received by this port during the selected interval, exceeding the Burst Excess value.
C32 prtFrTxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.22	Counter32	read-only	Number of data frames sent by this port during the selected interval, exceeding the Burst Excess value.
C32 prtFrRxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.23	Counter32	read-only	Number of data frames received by this port during the selected interval, exceeding the Burst Committed value.
C32 prtFrTxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.24	Counter32	read-only	Number of data frames sent by this port during the selected interval, exceeding the Burst Committed value.
prtCrStatis	1.3.6.1.4.1.164.3.1.4.1.3.2
prtCrStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.2.1		not-accessible	This table is applicable only for an active port running a CR protocol .
prtCrStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1		not-accessible	An entry in table.
INT prtCrStatisSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
INT prtCrStatisPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtCrStatisInvIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.3	INTEGER	read-only	The Interval of 15 min. for which the following statistics counters are applicable.
I32 prtCrTimeElapsed	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.4	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0.
C32 prtCrRxTotalCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.5	Counter32	read-only	The total number of cells received by this port during the selected interval.
C32 prtCrTxTotalCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.6	Counter32	read-only	The total number of cells sent by this port during the selected interval.
C32 prtCrRxDataCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.7	Counter32	read-only	The number of Data Cells received by this port during the selected interval.
C32 prtCrTxDataCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.8	Counter32	read-only	The number of Data Cells sent by this port during the selected interval.
prtDlciStatis	1.3.6.1.4.1.164.3.1.4.1.3.3
prtDlciStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.3.1		not-accessible	This table is applicable only for an active port running an FR, FR+ or CR protocol, with valid DLCIs .
prtDlciStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1		not-accessible	An entry in table.
INT prtDlciSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
INT prtDlciPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
I32 prtDlciIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.3	Integer32	read-only	This attribute indicates a unique DLCI index for each valid DLCI (16..991).
C32 prtDlciRxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.4	Counter32	read-only	The number of De frames received by this DLCI.
C32 prtDlciTxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.5	Counter32	read-only	The number of De frames sent by this DLCI.
C32 prtDlciRxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.6	Counter32	read-only	The number of De frames discarded due to congestion, received by this DLCI.
C32 prtDlciTxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.7	Counter32	read-only	The number of De frames discarded due to congestion, sent by this DLCI.
C32 prtDlciRxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.8	Counter32	read-only	All the frames discarded due to congestion, received by this DLCI.
C32 prtDlciTxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.9	Counter32	read-only	All the frames discarded due to congestion, sent by this DLCI.
C32 prtDlciTxFecn	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.10	Counter32	read-only	Number of frames sent by this DLCI, indicating forward congestion.
C32 prtDlciTxBecn	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.11	Counter32	read-only	Number of frames sent by this DLCI, indicating backward congestion.
C32 prtDlciRxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.12	Counter32	read-only	Number of data frames received by this DLCI, exceeding the Burst Excess value.
C32 prtDlciTxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.13	Counter32	read-only	Number of data frames sent by this DLCI, exceeding the Burst Excess value.
C32 prtDlciRxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.14	Counter32	read-only	Number of data frames received by this DLCI, exceeding the Burst Committed value.
C32 prtDlciTxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.15	Counter32	read-only	Number of data frames sent by this DLCI, exceeding the Burst Committed value.
prtT1Statis	1.3.6.1.4.1.164.3.1.4.1.3.4
prtT1FdlMsgTable	1.3.6.1.4.1.164.3.1.4.1.3.4.1		not-accessible	This table is applicable for a T1 interface with 'esf' LineType .
prtT1FdlMsgEntry	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1		not-accessible	An entry in table.
INT prtT1FdlMsgSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtT1FdlMsgPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.2	INTEGER	read-only	This attribute indicates a unique port number. MTML-1/T1 modules have just one external interface.
INT prtT1FdlMsgFdlTxRx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.3	INTEGER	read-only	The Fdl tx/rx reference of the Fdl message.
OCT prtT1FdlMsg	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.4	OCTET STRING	read-only	FDL message.
cnfgPrtGen	1.3.6.1.4.1.164.3.1.4.2
prtExTsSplitTable	1.3.6.1.4.1.164.3.1.4.2.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExTsBitTest that will be written directly to the Active Configuration.
prtExTsSplitEntry	1.3.6.1.4.1.164.3.1.4.2.1.1		not-accessible	An entry in table.
I32 prtExTsCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExTsSltIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units.
I32 prtExTsPrtIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.3	Integer32	read-only	This attribute indicates a unique port number. Most ML cards have only one external interface. inPrt1 - for MTML-H/E1 cards. For other products' index see their specification.
I32 prtExTsIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling.
I32 prtExTsBit	1.3.6.1.4.1.164.3.1.4.2.1.1.5	Integer32	read-only	This attribute indicates a unique Bit within the time slot. The valid Bits are: 1..8. 255=NA.
INT prtExTsIConSlot	1.3.6.1.4.1.164.3.1.4.2.1.1.6	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units.
I32 prtExTsIConPrt	1.3.6.1.4.1.164.3.1.4.2.1.1.7	Integer32	read-write	This attribute indicates the internally (In Mux) connected/routed port. For other products' index see their specification.
INT prtExTsBitTest	1.3.6.1.4.1.164.3.1.4.2.1.1.8	INTEGER	read-write	This attribute indicates a test to be activated on the selected Bit. It is applicable only when prtExPh1MlTsTest=split(254). none - no test is applied for the selected Bit. notApplicable - when prtExPh1MlTsTest is NOT split(254).
OCT prtExTsTxSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.9	OCTET STRING	read-only	Link - Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is sent to Link for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExTsRxSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.10	OCTET STRING	read-only	Link - Rx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is received from Link for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExTsTxIoSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.11	OCTET STRING	read-only	IO - Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is sent to IO port for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExTsRxIoSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.12	OCTET STRING	read-only	IO - Rx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is received from IO port for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
prtCnfgAgenda	1.3.6.1.4.1.164.3.1.4.2.2
prtAgendaBehaviourTable	1.3.6.1.4.1.164.3.1.4.2.2.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtAgendaBehaviourEntry	1.3.6.1.4.1.164.3.1.4.2.2.1.1		not-accessible	An entry in table.
I32 prtAgendaBehaviourCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtAgendaBehaviourSltIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.2	Integer32	read-only	This parameter should be: - slot number for MX3000 - 255 = N/A for MX300/30.
I32 prtAgendaBehaviourPrtIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.3	Integer32	read-only	This parameter should be: - port number for MX300/30 - 100 = N/A for MX3000.
INT prtAgendaBehaviourOnOff	1.3.6.1.4.1.164.3.1.4.2.2.1.1.4	INTEGER	read-write	Setting this command to on(3) enables the agenda function at module (3000) or port (300/30) level.
prtCnfgAgendaTable	1.3.6.1.4.1.164.3.1.4.2.2.2		not-accessible	This table allows the user to schedule the time a session is active per week basis.
prtCnfgAgendaEntry	1.3.6.1.4.1.164.3.1.4.2.2.2.1		not-accessible	An entry in table.
I32 prtCnfgAgendaCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtCnfgAgendaSltIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.2	Integer32	read-only	This attribute is equal to: -slot number for MX3000 -255 = N/A for MX300/30
I32 prtCnfgAgendaPrtIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.3	Integer32	read-only	This attribute is equal to: - port number for MX300/30 - port number for MX3000. For example 1-4 in MHS-4 cards. - 100 = N/A for MX3000 when not used.
INT prtCnfgAgendaDayIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.4	INTEGER	read-only	This attribute for which day of the week this row applies.
I32 prtCnfgAgendaSesId	1.3.6.1.4.1.164.3.1.4.2.2.2.1.5	Integer32	read-only	The user may define 4 different active intervals per day.
I32 prtCnfgAgendaFrom	1.3.6.1.4.1.164.3.1.4.2.2.2.1.6	Integer32	read-write	Start from time interval in seconds.
I32 prtCnfgAgendaTo	1.3.6.1.4.1.164.3.1.4.2.2.2.1.7	Integer32	read-write	To time interval in seconds.
prtGenCnfgTable	1.3.6.1.4.1.164.3.1.4.2.3		not-accessible	This table allows the user to configure general port parameters.
prtGenCnfgEntry	1.3.6.1.4.1.164.3.1.4.2.3.1		not-accessible	An entry in table.
I32 prtGenCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
INT prtGenCnfgSltIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
I32 prtGenCnfgPrtIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.3	Integer32	read-only	This attribute indicates a unique external or internal port number. For MP: exPrt1 (1) .. exPrt16 (16) , notApplicable(100), inPrt1 (101) .. inPrt84 (184)
INT prtGenCnfgLinkToSlot	1.3.6.1.4.1.164.3.1.4.2.3.1.4	INTEGER	read-write	This attribute indicates the slot of the ML card to which the IO port is mapped.
I32 prtGenCnfgLinkToPort	1.3.6.1.4.1.164.3.1.4.2.3.1.5	Integer32	read-write	This attribute indicates the port in the prtGenCnfgLinkToSlot of the ML card to which the IO port is mapped. For MP: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109), inPrt10 (110), inPrt11 (111), inPrt12 (112), inPrt13 (113), inPrt14 (114), inPrt15 (115), inPrt16 (116), inPrt17 (117), inPrt18 (118), inPrt19 (119), inPrt20 (120), inPrt21 (121), inPrt22 (122), inPrt23 (123), inPrt24 (124), inPrt25 (125), inPrt26 (126), inPrt27 (127), inPrt28 (128), inPrt29 (129), inPrt30 (130), inPrt31 (131), inPrt32 (132), inPrt33 (133), inPrt34 (134), inPrt35 (135), inPrt36 (136), inPrt37 (137), inPrt38 (138), inPrt39 (139), inPrt40 (140), inPrt41 (141), inPrt42 (142), inPrt43 (143), inPrt44 (144), inPrt45 (145), inPrt46 (146), inPrt47 (147), inPrt48 (148), inPrt49 (149), inPrt50 (150), inPrt51 (151), inPrt52 (152), inPrt53 (153), inPrt54 (154), inPrt55 (155), inPrt56 (156), inPrt57 (157), inPrt58 (158), inPrt59 (159), inPrt60 (160), inPrt61 (161), inPrt62 (162), inPrt63 (163), inPrt64 (164), inPrt65 (165), inPrt66 (166), inPrt67 (167), inPrt68 (168), inPrt69 (169), inPrt70 (170), inPrt71 (171), inPrt72 (172), inPrt73 (173), inPrt74 (174), inPrt75 (175), inPrt76 (176), inPrt77 (177), inPrt78 (178), inPrt79 (179), inPrt80 (180), inPrt81 (181), inPrt82 (182), inPrt83 (183), inPrt84 (184), notApplicable (255)
I32 prtGenCnfgPortId	1.3.6.1.4.1.164.3.1.4.2.3.1.6	Integer32	read-write	IO Port Id for V5.1 use. This object is applicable only for part of the PSTN and ISDN IO ports. Generally, 0 is a valid value. Nevertheless, for ports that do not support this object, the value will be: notApplicable= 0
INT prtGenCnfgBusConnection	1.3.6.1.4.1.164.3.1.4.2.3.1.7	INTEGER	read-write	This object indicates the support of the card regarding Bus Connection. Same value for all ports of the card. partial = 2 Buses (AB) full = 4 Buses (ABCD) partial CD = 2 Buses CD Actually the support depends on the card's HW. But, since CL has to assign data on Buses even when the card is not installed, this object has to be configured. If the actual card installed will not match the value configured, an Alarm will be issued.
INT prtGenCnfgInbandMng	1.3.6.1.4.1.164.3.1.4.2.3.1.8	INTEGER	read-write	This object indicates whether Inband Management is used over the link.
INT prtGenCnfgInbandMngRoutProt	1.3.6.1.4.1.164.3.1.4.2.3.1.9	INTEGER	read-write	This object indicates the Inband Mng Routing Protocol of the port.
INT prtGenCnfgProtectionMode	1.3.6.1.4.1.164.3.1.4.2.3.1.10	INTEGER	read-write	This object indicates the Protection Mode of the port. notApplicable- when Bus Protection Point=No. For VC-4/Omni card this object is supported RO.
INT prtGenCnfgConnect	1.3.6.1.4.1.164.3.1.4.2.3.1.11	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtGenCnfgSignalingType	1.3.6.1.4.1.164.3.1.4.2.3.1.12	INTEGER	read-write	This object selects the Type of Signaling used by the port.
cmprPrtGen	1.3.6.1.4.1.164.3.1.4.3
prtCmprTable	1.3.6.1.4.1.164.3.1.4.3.1		not-accessible	A table.
prtCmprEntry	1.3.6.1.4.1.164.3.1.4.3.1.1		not-accessible	An entry in table.
I32 prtCmprTypIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 prtCmprCnfgIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 prtCmprVersion	1.3.6.1.4.1.164.3.1.4.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
INT prtCmprSltIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
I32 prtCmprPrtIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.5	Integer32	read-only	This attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148).
OCT prtCmprObj	1.3.6.1.4.1.164.3.1.4.3.1.1.6	OCTET STRING	read-write	This attribute is the compressed information itself.
OCT prtCmprStatisticObj	1.3.6.1.4.1.164.3.1.4.3.1.1.7	OCTET STRING	read-only	This attribute is the compressed statistics information itself.
prtDlciCmprTable	1.3.6.1.4.1.164.3.1.4.3.2		not-accessible	A table.
prtDlciCmprEntry	1.3.6.1.4.1.164.3.1.4.3.2.1		not-accessible	An entry in table.
I32 prtDlciCmprCnfgIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.1	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 prtDlciCmprVersion	1.3.6.1.4.1.164.3.1.4.3.2.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
INT prtDlciCmprSltIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.3	INTEGER	read-only	This attribute indicates a unique number of the slot position where the module is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
INT prtDlciCmprPrtIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.4	INTEGER	read-only	This attribute indicates a unique identifier of the port the compressed information relates to. All the values are valid.
I32 prtDlciCmprDlciIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.5	Integer32	read-only	This attribute indicates a unique identifier of the Dlci the compressed information relates to. The values are between 16 - 991.
OCT prtDlciCmprObj	1.3.6.1.4.1.164.3.1.4.3.2.1.6	OCTET STRING	read-write	This attribute is the compressed information itself.
prtAlarmsCmprTable	1.3.6.1.4.1.164.3.1.4.3.3		not-accessible	A table.
prtAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.4.3.3.1		not-accessible	An entry in table.
I32 prtAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.4.3.3.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 prtAlarmsCmprAlarmSlot	1.3.6.1.4.1.164.3.1.4.3.3.1.2	Integer32	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For Stand-alone units, notApplicable(255) will appear.
I32 prtAlarmsCmprAlarmPort	1.3.6.1.4.1.164.3.1.4.3.3.1.3	Integer32	read-only	This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a non-existing port. IP Bundles are considered a port too, for this matter.
I32 prtAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.4.3.3.1.4	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
OCT prtAlarmsCmprObj	1.3.6.1.4.1.164.3.1.4.3.3.1.5	OCTET STRING	read-only	This attribute is the compressed information itself.
mapWanGen	1.3.6.1.4.1.164.3.1.5
agnLinkMapTable	1.3.6.1.4.1.164.3.1.5.1		not-accessible	A table.
agnLinkMapEntry	1.3.6.1.4.1.164.3.1.5.1.1		not-accessible	An entry in table.
I32 mapLinkId	1.3.6.1.4.1.164.3.1.5.1.1.1	Integer32	read-only	A unique identifier of the link
INT mapLinkSltIdx	1.3.6.1.4.1.164.3.1.5.1.1.2	INTEGER	read-write	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries clA(3), io6(10)..io12(16) are not valid.
INT mapLinkPrtIdx	1.3.6.1.4.1.164.3.1.5.1.1.3	INTEGER	read-write	This attribute indicates a unique port number.
INT mapLinkStatus	1.3.6.1.4.1.164.3.1.5.1.1.4	INTEGER	read-only	This attribute indicates the status of the link between the two muxes
diverseIfWanGen	1.3.6.1.4.1.164.3.1.6
ethIf	1.3.6.1.4.1.164.3.1.6.1
ethIfTable	1.3.6.1.4.1.164.3.1.6.1.1		not-accessible	A table.
ethIfEntry	1.3.6.1.4.1.164.3.1.6.1.1.1		not-accessible	An entry in table.
I32 ethIfIdx	1.3.6.1.4.1.164.3.1.6.1.1.1.1	Integer32	read-only	A unique index of the ethernet interface/port.
INT ethMode	1.3.6.1.4.1.164.3.1.6.1.1.1.2	INTEGER	read-write	This object indicates the Ethernet mode of operation.
INT ethBridgingMode	1.3.6.1.4.1.164.3.1.6.1.1.1.3	INTEGER	read-write	This object indicates the bridging mode of the Ethernet interface.
INT ethEncapsulationCRCMode	1.3.6.1.4.1.164.3.1.6.1.1.1.4	INTEGER	read-write	This object define the encapsulation type requested for the Ethernet interface. It indicates if we transfer the Ethernet frame to the other side with or without the CRC.
INT ethBackPressure	1.3.6.1.4.1.164.3.1.6.1.1.1.5	INTEGER	read-write	This parameter defines whether to enable or disable Back pressure. Back Pressure is a flow control parameter.
INT ethLimit4	1.3.6.1.4.1.164.3.1.6.1.1.1.6	INTEGER	read-write	This parameter determine the Back off algorithm mode. Every 4 following collisions the Framer will be thrown out (4 times more than usuall).
INT ethSkipInitReset	1.3.6.1.4.1.164.3.1.6.1.1.1.7	INTEGER	read-write	This parameter defines whether read status on reset.
INT ethMulticastBlock	1.3.6.1.4.1.164.3.1.6.1.1.1.8	INTEGER	read-write	This parameter defines whether to send multicast message to WAN from LAN or not.
INT ethBroadcastBlock	1.3.6.1.4.1.164.3.1.6.1.1.1.9	INTEGER	read-write	This parameter defines whether to send broadcast message to WAN from LAN or not.
INT ethSpeed	1.3.6.1.4.1.164.3.1.6.1.1.1.10	INTEGER	read-write	This parameter defines the line speed.
INT ethRip2	1.3.6.1.4.1.164.3.1.6.1.1.1.11	INTEGER	read-write	This parameter defines whether to send RIP II message to WAN from LAN or not
INT ethPortPriority	1.3.6.1.4.1.164.3.1.6.1.1.1.12	INTEGER	read-write	This parameter defines if priority is to be considered for this Port.
INT ethPortMngEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.13	INTEGER	read-write	This parameter defines whether management data can pass through this Port. localOnly (4) - Only local device can be managed via this port.
MAC ethFlowCtrlMacAddress	1.3.6.1.4.1.164.3.1.6.1.1.1.14	MacAddress	read-write	In case of flow control - transmit frame with this specific MAC address to inform the other end to stop sending frames. Default: 01.80.C2.00.00.01.
I32 ethRateLimit	1.3.6.1.4.1.164.3.1.6.1.1.1.15	Integer32	read-write	This parameter defines the Rate Limit of the line, in Mbps.
INT ethJumboFrameEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.16	INTEGER	read-write	This parameter defines whether to support Jumbo Frame or not.
INT ethAutoMdiXEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.17	INTEGER	read-write	This parameter defines whether to support automatic change between MDI and MDI[X].
INT ethPortDataEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.18	INTEGER	read-write	This parameter defines whether this port is enabled for data (that is not management). no(2) - management can run on this port yes(3) - both management and payload data can run on this port.
I32 ethIfUse	1.3.6.1.4.1.164.3.1.6.1.1.1.19	Integer32	read-write	This parameter defines the use of the port. 1=NET 2=USER .
INT ethLineOam	1.3.6.1.4.1.164.3.1.6.1.1.1.20	INTEGER	read-write	This parameter defines the working mode of 802.AH OAM mechanism.
INT ethRoutingProtocol	1.3.6.1.4.1.164.3.1.6.1.1.1.21	INTEGER	read-write	This parameter defines the routing protocol used above ETH port.
INT ethMdiXManualSwitch	1.3.6.1.4.1.164.3.1.6.1.1.1.22	INTEGER	read-write	This parameter sets the port to be MDI-X (cross-over) or MDI (straight-through). It is applicable only when ethAutoMdiXEnable = no, namely, only when the automatic MDI/MDIX crossover function is disabled.
INT ethDot1xEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.23	INTEGER	read-write	Determines if the Port-Based Network Access Protocol (IEEE-802.1x) is enabled for the Ethernet Port.
INT ethPartnerRateMode	1.3.6.1.4.1.164.3.1.6.1.1.1.24	INTEGER	read-write	For converters having couples of ports, where each couple contains a port with an SFP connector and a port with a RJ connector, this parameter is relevant for the SFP port. It affects Rate configuration of its partner (RJ port). manual - user can configure manually ETH parameters of RJ port (e.g Autonegotiation, Max Capability Advertised, etc...) automatic - SFP Rate will be enforced on the RJ port. In this mode, user cannot configure the Rate related parameters of the RJ port (e.g Autonegotiation, Max Capability Advertised, etc...)
INT ethDot1xPortRole	1.3.6.1.4.1.164.3.1.6.1.1.1.25	INTEGER	read-write	Determine the functionality of the port in the Port-Based Network Access Protocol (IEEE-802.1x) - either Authenticator or Supplicant.
ethIfPerformance	1.3.6.1.4.1.164.3.1.6.1.2
ethIfCurrentTable	1.3.6.1.4.1.164.3.1.6.1.2.1		not-accessible	The Ethernet Current table. When the index specifies the Ethernet interface (only), the counters are for an interval of 15 minutes.
ethIfCurrentEntry	1.3.6.1.4.1.164.3.1.6.1.2.1.1		not-accessible	An entry in the Ethernet Current table.
I32 ethIfCurrentIndex	1.3.6.1.4.1.164.3.1.6.1.2.1.1.1	Integer32	read-only	The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval type can indicate: 1 minute, 15 minutes, 1 hour, 24 hours. For the exact formula, see device specification.
OCT ethIfCurrentStatus	1.3.6.1.4.1.164.3.1.6.1.2.1.1.2	OCTET STRING	read-only	The status of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
G32 ethIfCurrentInFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.3	Gauge32	read-only	The counter associated with the number of received frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.4	Gauge32	read-only	The counter associated with the number of received octets, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentAlignmentErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.5	Gauge32	read-only	The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.6	Gauge32	read-only	The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentLengthError	1.3.6.1.4.1.164.3.1.6.1.2.1.1.7	Gauge32	read-only	The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.8	Gauge32	read-only	The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.9	Gauge32	read-only	The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentSingleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.10	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.11	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentDeferredTransmissions	1.3.6.1.4.1.164.3.1.6.1.2.1.1.12	Gauge32	read-only	The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentLateCollisions	1.3.6.1.4.1.164.3.1.6.1.2.1.1.13	Gauge32	read-only	The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentCarrierSenseErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.14	Gauge32	read-only	The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.1.1.15	Gauge32	read-only	The counter associated with the number of frames dropped due to lack of buffers in ingress pool, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.1.1.16	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the current interval.
G32 ethIfCurrentOverflowInFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.17	Gauge32	read-only	The number of times the associated ethIfCurrentInFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.18	Gauge32	read-only	The number of times the associated ethIfCurrentInOctets counter has overflowed in the current interval.
G32 ethIfCurrentOverflowFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.19	Gauge32	read-only	The number of times the associated ethIfCurrentFCSErrors counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.20	Gauge32	read-only	The number of times the associated ethIfCurrentOutFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.21	Gauge32	read-only	The number of times the associated ethIfCurrentOutOctets counter has overflowed in the current interval.
G32 ethIfCurrentOverflowMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.22	Gauge32	read-only	The number of times the associated ethIfCurrentMultipleCollisionFrames counter has overflowed in the current interval.
G32 ethIfCurrentInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.23	Gauge32	read-only	The number of received Unicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.24	Gauge32	read-only	The number of transmitted Unicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.25	Gauge32	read-only	The number of received Multicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.26	Gauge32	read-only	The number of transmitted Multicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.27	Gauge32	read-only	The number of received Broadcast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.28	Gauge32	read-only	The number of transmitted Broadcast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.29	Gauge32	read-only	The number of received Discarded frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.30	Gauge32	read-only	The number of transmitted Discarded frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.31	Gauge32	read-only	The number of received Pause frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.32	Gauge32	read-only	The number of transmitted Pause frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOverflowInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.33	Gauge32	read-only	The number of times the associated ethIfCurrentInUnicastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.34	Gauge32	read-only	The number of times the associated ethIfCurrentOutUnicastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.35	Gauge32	read-only	The number of times the associated ethIfCurrentInMulticastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.36	Gauge32	read-only	The number of times the associated ethIfCurrentOutMulticastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.37	Gauge32	read-only	The number of times the associated ethIfCurrentInBroadcastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.38	Gauge32	read-only	The number of times the associated ethIfCurrentOutBroadcastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.39	Gauge32	read-only	The number of times the associated ethIfCurrentInDiscardFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.40	Gauge32	read-only	The number of times the associated ethIfCurrentOutDiscardFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.41	Gauge32	read-only	The number of times the associated ethIfCurrentInPauseFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.42	Gauge32	read-only	The number of times the associated ethIfCurrentOutPauseFrames counter has overflowed in the current interval.
ethIfIntervalTable	1.3.6.1.4.1.164.3.1.6.1.2.2		not-accessible	The Ethernet Interval table. When ethIfIntervalIndex specifies the Ethernet interface (only), the counters are for an interval of 15 minutes.
ethIfIntervalEntry	1.3.6.1.4.1.164.3.1.6.1.2.2.1		not-accessible	An entry in the Ethernet Interval table.
I32 ethIfIntervalIndex	1.3.6.1.4.1.164.3.1.6.1.2.2.1.1	Integer32	read-only	The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval type can indicate: 1 minute, 15 minutes, 1 hour, 24 hours. For the exact formula, see device specification.
I32 ethIfIntervalNumber	1.3.6.1.4.1.164.3.1.6.1.2.2.1.2	Integer32	read-only	The Interval Number. This number is between 1 and x, where 1 is the most recently completed interval and x is the least recently completed interval. For 15 minute intervals, usually x=96, but it can be different, depending on device capabilities.
OCT ethIfIntervalStatus	1.3.6.1.4.1.164.3.1.6.1.2.2.1.3	OCTET STRING	read-only	The status of the interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
G32 ethIfIntervalInFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.4	Gauge32	read-only	The counter associated with the number of received frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.5	Gauge32	read-only	The counter associated with the number of received octets, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalAlignmentErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.6	Gauge32	read-only	The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the interval.
G32 ethIfIntervalFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.7	Gauge32	read-only	The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalLengthError	1.3.6.1.4.1.164.3.1.6.1.2.2.1.8	Gauge32	read-only	The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.9	Gauge32	read-only	The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.10	Gauge32	read-only	The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalSingleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.11	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.12	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalDeferredTransmissions	1.3.6.1.4.1.164.3.1.6.1.2.2.1.13	Gauge32	read-only	The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalLateCollisions	1.3.6.1.4.1.164.3.1.6.1.2.2.1.14	Gauge32	read-only	The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalCarrierSenseErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.15	Gauge32	read-only	The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.2.1.16	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Receive direction to the Ethernet interface in the interval.
G32 ethIfIntervalOutputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.2.1.17	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the interval.
G32 ethIfIntervalOverflowInFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.18	Gauge32	read-only	The number of times the associated ethIfIntervalInFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.19	Gauge32	read-only	The number of times the associated ethIfIntervalInOctets counter has overflowed in the interval.
G32 ethIfIntervalOverflowFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.20	Gauge32	read-only	The number of times the associated ethIfIntervalFCSErrors counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.21	Gauge32	read-only	The number of times the associated ethIfIntervalOutFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.22	Gauge32	read-only	The number of times the associated ethIfIntervalOutOctets counter has overflowed in the interval.
G32 ethIfIntervalOverflowMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.23	Gauge32	read-only	The number of times the associated ethIfIntervalMultipleCollisionFrames counter has overflowed in the interval.
G32 ethIfIntervalInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.24	Gauge32	read-only	The number of received Unicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.25	Gauge32	read-only	The number of transmitted Unicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.26	Gauge32	read-only	The number of received Multicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.27	Gauge32	read-only	The number of transmitted Multicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.28	Gauge32	read-only	The number of received Broadcast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.29	Gauge32	read-only	The number of transmitted Broadcast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.30	Gauge32	read-only	The number of received Discarded frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.31	Gauge32	read-only	The number of transmitted Discarded frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.32	Gauge32	read-only	The number of received Pause frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.33	Gauge32	read-only	The number of transmitted Pause frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOverflowInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.34	Gauge32	read-only	The number of times the associated ethIfIntervalInUnicastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.35	Gauge32	read-only	The number of times the associated ethIfIntervalOutUnicastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.36	Gauge32	read-only	The number of times the associated ethIfIntervalInMulticastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.37	Gauge32	read-only	The number of times the associated ethIfIntervalOutMulticastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.38	Gauge32	read-only	The number of times the associated ethIfIntervalInBroadcastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.39	Gauge32	read-only	The number of times the associated ethIfIntervalOutBroadcastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.40	Gauge32	read-only	The number of times the associated ethIfIntervalInDiscardFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.41	Gauge32	read-only	The number of times the associated ethIfIntervalOutDiscardFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.42	Gauge32	read-only	The number of times the associated ethIfIntervalInPauseFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.43	Gauge32	read-only	The number of times the associated ethIfIntervalOutPauseFrames counter has overflowed in the interval.
INT ethPerformanceMode	1.3.6.1.4.1.164.3.1.6.1.2.3	INTEGER	read-write	This object indicates whether OK or Fail statistics will be counted.
ethIfPerfTable	1.3.6.1.4.1.164.3.1.6.1.2.4		not-accessible	The Ethernet Performance table.
ethIfPerfEntry	1.3.6.1.4.1.164.3.1.6.1.2.4.1		not-accessible	An entry in the Ethernet Performance table.
G32 ethIfPerfInOkFrames	1.3.6.1.4.1.164.3.1.6.1.2.4.1.1	Gauge32	read-only	The counter associated with the number of received OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
G32 ethIfPerfOutOkFrames	1.3.6.1.4.1.164.3.1.6.1.2.4.1.2	Gauge32	read-only	The counter associated with the number of transmitted OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
G32 ethIfPerfTotalCollisions	1.3.6.1.4.1.164.3.1.6.1.2.4.1.3	Gauge32	read-only	The counter associated with the total number of collisions of any type encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done
G32 ethIfPerfInOkOctets	1.3.6.1.4.1.164.3.1.6.1.2.4.1.4	Gauge32	read-only	The counter associated with the number of received OK Octets, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
ethIfOamCfm	1.3.6.1.4.1.164.3.1.6.1.3
ethIfOamCfmEvents	1.3.6.1.4.1.164.3.1.6.1.3.0
NTF ethOamCfmDefectCondition	1.3.6.1.4.1.164.3.1.6.1.3.0.1			This trap indicates that a MEP has a persistent defect condition.
radMepTable	1.3.6.1.4.1.164.3.1.6.1.3.1		not-accessible	MEG End Point (MEP) configuration table associated with Maitenance Entity Group (MEG) End Point. MEP is a short name for an expanded ETH flow point that includes a compound ETH Segment flow termination function, which marks the end point of an ETH ME, and a compound ETH Diagnostic flow function.
radMepEntry	1.3.6.1.4.1.164.3.1.6.1.3.1.1		not-accessible	An entry in the table.
U32 radOamIdx1	1.3.6.1.4.1.164.3.1.6.1.3.1.1.1	Unsigned32	not-accessible	This object may indicate the Bridge Index or Configuration index.
U32 radOamEvcIdx	1.3.6.1.4.1.164.3.1.6.1.3.1.1.2	Unsigned32	not-accessible	This object indicates the Index of the EVC (Ethernet Virtual Circuit) that the MEP is associated to.
U32 radMepIdx	1.3.6.1.4.1.164.3.1.6.1.3.1.1.3	Unsigned32	not-accessible	This object indicates the ID of the MEP being accessed.
ROW radMepRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.1.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table.
U32 radMepLocalMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.5	Unsigned32	read-create	This object indicates the local MEP ID.
U32 radMepRemoteMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.6	Unsigned32	read-create	This atribute is currently implemneted at radMepCcTable, that supports multicast.
INT radMepOamMode	1.3.6.1.4.1.164.3.1.6.1.3.1.1.7	INTEGER	read-create	This object determines the OAM mode of the MEP: disabled - no CC is initiated nor responded initiate - the device initiates and responds to CC react - the device does not initiate a CC, but responds to CC.
INT radMepContinuityVerMode	1.3.6.1.4.1.164.3.1.6.1.3.1.1.8	INTEGER	read-create	This object determines the OAM behavior of the MEP: disabled - no CC is done cc_based - CC is done based on incoming messages lb_based - CC is done based on loopback messages.
U32 radMepMeLevel	1.3.6.1.4.1.164.3.1.6.1.3.1.1.9	Unsigned32	read-create	At any point in a network, ME Level is used to distinguish between OAM signals belonging to different nested MEs. Maintenance Entity Levels are defined as follows: 0,1,2 are assigned to customers 3,4 are assigned to providers 5,6,7 are assigned to operators.
INT radMepOamDestAddrType	1.3.6.1.4.1.164.3.1.6.1.3.1.1.10	INTEGER	read-create	This object determines if the OAM messages are sent to user defined unicast address, or to RAD proprietary multicast address.
MAC radMepOamDestMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.1.1.11	MacAddress	read-create	This object determines the MAC address that OAM packets are sent to.
U32 radMepDefaultPriority	1.3.6.1.4.1.164.3.1.6.1.3.1.1.12	Unsigned32	read-create	This object defines the priority of the OAM messages sent when no service is defined on EVC. If a service is defined, the OAM messages will get the highest service priority existing on the EVC.
INT radMepCcStatus	1.3.6.1.4.1.164.3.1.6.1.3.1.1.13	INTEGER	read-only	This object indicates the Continuity Check (CC) status.
INT radMepOamProtocol	1.3.6.1.4.1.164.3.1.6.1.3.1.1.14	INTEGER	read-create	Determines whether to use proprietary OAM mechanism, or to use the standard (IEEE 802.1ag, ITU-T Y.1731).
U32 radMepMdId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.15	Unsigned32	read-create	The index of the Maintenance Domain in the radMdTable (radMdIndex).
INT radMepMaFormat	1.3.6.1.4.1.164.3.1.6.1.3.1.1.16	INTEGER	read-create	The type (and thereby format) of the Maintenance Association Name.
OCT radMepMaName	1.3.6.1.4.1.164.3.1.6.1.3.1.1.17	OCTET STRING	read-create	The Short Maintenance Association name.
U32 radMepSpVlanId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.18	Unsigned32	read-create	The SP (Service Provider) VLAN used when sending an OAM message.
INT radMepCcInterval	1.3.6.1.4.1.164.3.1.6.1.3.1.1.19	INTEGER	read-create	Indicates the interval at which CCMs are sent by a MEP Valid only if radMepOamMode = initiate(4).
MAC radMepTransmitLbmDestMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.1.1.20	MacAddress	read-create	The Target MAC Address Field to be transmitted in the Loopback Message: For unicast MAC Address this is the unicast destination MAC address. For multicast MAC Address, this variable is read-only. This address will be used if the value of radMepTransmitLbmDestIsMepId is no (2). 802.1ag clause 12.14.7.3.2:b.
U32 radMepTransmitLbmDestMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.21	Unsigned32	read-create	The MEPID of another MEP in the same MA to which the LBM is to be sent. This address will be used if the value of radMepTransmitLbmDestIsMepId is yes (3). 802.1ag clause 12.14.7.3.2:b.
INT radMepTransmitLbmDestIsMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.22	INTEGER	read-create	yes (3) indicates that MEPID of the target MEP is used for loopback transmission. no (2) indicates that unicast destination MAC address of the target MEP is used. 802.1ag clause 12.14.7.3.2:b.
I32 radMepTransmitLbmMassages	1.3.6.1.4.1.164.3.1.6.1.3.1.1.23	Integer32	read-create	The number of Loopback messages to be transmitted.
U32 radMepTransmitLbmVlanPriority	1.3.6.1.4.1.164.3.1.6.1.3.1.1.24	Unsigned32	read-create	The priority to be used in the VLAN tag, if present, in the transmitted frame. The default value is CCM priority. 802.1ag clause 12.14.7.3.2:e
INT radMepTransmitLbmVlanDropEnable	1.3.6.1.4.1.164.3.1.6.1.3.1.1.25	INTEGER	read-create	Drop Enable bit to be used in the VLAN tag, if present, in the transmitted frame. 802.1ag clause 12.14.7.3.2:e
C32 radMepLbrIn	1.3.6.1.4.1.164.3.1.6.1.3.1.1.26	Counter32	read-only	Total number of valid, in-order Loopback Replies received.
C32 radMepLbrInOutOfOrder	1.3.6.1.4.1.164.3.1.6.1.3.1.1.27	Counter32	read-only	The total number of valid, out-of-order Loopback Replies received.
C32 radMepLbmOut	1.3.6.1.4.1.164.3.1.6.1.3.1.1.28	Counter32	read-only	Total number of Loopback Messages transmitted.
MAC radMepTransmitLtmTargetMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.1.1.29	MacAddress	read-create	The Target MAC Address Field to be transmitted in the Link Trace Message: A unicast destination MAC address. This address will be used if the value of radMepTransmitLtmTargetIsMepId is no (2). 802.1ag clause 12.14.7.4.2:c.
U32 radMepTransmitLtmTargetMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.30	Unsigned32	read-create	The MEPID of another MEP in the same MA to which LTM is to be transmitted. This address will be used if the value of radMepTransmitLtmTargetIsMepId is yes (3). 802.1ag clause 12.14.7.4.2:c.
INT radMepTransmitLtmTargetIsMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.31	INTEGER	read-create	yes (3) indicates that MEPID of the target MEP is used for Linktrace transmission. no (2) indicates that unicast destination MAC address of the target MEP is used. 802.1ag clause 12.14.7.4.2:c.
U32 radMepTransmitLtmTtl	1.3.6.1.4.1.164.3.1.6.1.3.1.1.32	Unsigned32	read-create	The LTM TTL field. Default value, if not specified, is 64. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 each Linktrace Responder that handles the LTM. The value received in the LTM is returned in the LTR. If 0 on input, the LTM is not transmitted to the next hop. 802.1ag clause 12.14.7.4.2:b and 21.8.4.
INT radMepTransmitLtmActivationCmd	1.3.6.1.4.1.164.3.1.6.1.3.1.1.33	INTEGER	read-create	Activation command for starting Loop Trace. Set will be always to 'on' value. After operation was finished, Agent will turn the value to 'off'.
ethOamService	1.3.6.1.4.1.164.3.1.6.1.3.2
ethOamServiceTable	1.3.6.1.4.1.164.3.1.6.1.3.2.1		not-accessible	Service configuration table associated with Services running on a MEP.
ethOamServiceEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1		not-accessible	An entry in the table.
U32 ethOamServiceIdx	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.1	Unsigned32	not-accessible	This object indicates the Index of the service being accessed.
ROW ethOamServiceRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.2	RowStatus	read-create	This attribute allows to create/delete a row in this table.
U32 ethOamServicePriority	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.3	Unsigned32	read-create	This object determines the priority of the service. It is sent as P bits in an OAM message originated by this service.
INT ethOamServicePmEnable	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.4	INTEGER	read-create	This object determines PM (Performance Monitoring) shall be enabled or not for the service.
I32 ethOamServiceFrameLossRatioThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.5	Integer32	read-create	This object determines the Frame Loss ratio threshold in exponent of 1/10. That is, a value of 4 means that the threshold is 1E-4.
I32 ethOamServiceDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.6	Integer32	read-create	This object determines the delay threshold defined for this service, in measurement unit of 0.1 msec.
I32 ethOamServiceDelayVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.7	Integer32	read-create	This object determines the delay variation threshold defined for this service, in measurement unit of 0.1 msec.
I32 ethOamServiceUnavailRatioThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.8	Integer32	read-create	This object determines the Unavailability ratio threshold in exponent of 1/10. That is, a value of 4 means that the threshold is 1E-4.
C32 ethOamServiceTxFrames	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.9	Counter32	read-only	Counts the number of frames trnasmitted by since the time the service is up.
C32 ethOamServiceOverflowTxFrames	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.10	Counter32	read-only	The number of times the associated ethOamServiceTxFrames counter has overflowed.
C32 ethOamServiceFrameLoss	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.11	Counter32	read-only	Counts the number of frames lost since the time the service is up.
C32 ethOamServiceOverflowFrameLoss	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.12	Counter32	read-only	The number of times the associated ethOamServiceFrameLoss counter has overflowed.
U32 ethOamServiceFrameLossRatio	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.13	Unsigned32	read-only	Indicates the ratio of the lost frames since the time the service is up. The value is the ratio multiplied by 1E10. 0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).
C32 ethOamServiceElapsedTime	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.14	Counter32	read-only	Indicates the time elapsed in seconds since the time the service is up.
C32 ethOamServiceUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.15	Counter32	read-only	Indicates the number of unavailable seconds since the time the service is up.
U32 ethOamServiceUnavailRatio	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.16	Unsigned32	read-only	Indicates the ratio of the unavailable seconds since the time the service is up. The value is the ratio multiplied by 1E10. 0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).
C32 ethOamServiceFramesAboveDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.17	Counter32	read-only	Indicates the number of frames arrived with delay greater than the delay threshold.
C32 ethOamServiceOverflowFramesAboveDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.18	Counter32	read-only	Indicates the number of times the associated ethOamServiceFramesAboveDelay counter has overflowed.
C32 ethOamServiceFramesAboveDelayVar	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.19	Counter32	read-only	Indicates the number of frames arrived with delay variation greater than the delay variation threshold.
C32 ethOamServiceOverflowFramesAboveDelayVar	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.20	Counter32	read-only	Indicates the number of times the associated ethOamServiceFramesAboveDelayVar counter has overflowed.
ethOamSvcCurrentStatTable	1.3.6.1.4.1.164.3.1.6.1.3.2.2		not-accessible	Service Current Statistics Table.
ethOamSvcCurrentStatEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1		not-accessible	Current Statistics per service
PER ethOamSvcCurrFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.1	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay greater than the threshold value defined for the service.
PER ethOamSvcCurrFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.2	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay lower than or equal to the threshold value defined for the service.
PER ethOamSvcCurrFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.3	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay variation greater than the threshold value defined for the service.
PER ethOamSvcCurrFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.4	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay variation lower than or equal to the threshold value defined for the service.
PER ethOamSvcCurrFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.5	PerfCurrentCount	read-only	Number of trnasmitted frames in the current interval.
PER ethOamSvcCurrFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.6	PerfCurrentCount	read-only	Number of lost frames in the current interval.
U32 ethOamSvcCurrMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.7	Unsigned32	read-only	The mininal value of round trip delay in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.8	Unsigned32	read-only	The maximum value of round trip delay in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.9	Unsigned32	read-only	The average round trip delay in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.10	Unsigned32	read-only	The maximum value of round trip delay variation in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.11	Unsigned32	read-only	The average round trip delay variation in the current interval. Values units are of 0.1 msec.
I32 ethOamSvcCurrElapsedTime	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.12	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current interval.
PER ethOamSvcCurrUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.13	PerfCurrentCount	read-only	The number of seconds that the service was unavailable in the current interval.
ethOamSvcIntervalTable	1.3.6.1.4.1.164.3.1.6.1.3.2.3		not-accessible	Service Interval Statistics Table.
ethOamSvcIntervalEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1		not-accessible	Interval Statistics per service
I32 ethOamSvcIntervalNum	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.1	Integer32	not-accessible	The Interval index, which is actualy the Interval number, where 1 is the most recently completed 15 minute interval, and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
NUM ethOamSvcIntervalFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.2	PerfIntervalCount	read-only	Number of frames that arrived in a delay greater than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.3	PerfIntervalCount	read-only	Number of frames that arrived in a delay lower than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.4	PerfIntervalCount	read-only	Number of frames that arrived in a delay variation greater than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.5	PerfIntervalCount	read-only	Number of frames that arrived in a delay variation lower than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.6	PerfIntervalCount	read-only	Number of trnasmitted frames in the selected interval.
NUM ethOamSvcIntervalFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.7	PerfIntervalCount	read-only	Number of lost frames in the selected interval.
U32 ethOamSvcIntervalMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.8	Unsigned32	read-only	The mininal value of round trip delay in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.9	Unsigned32	read-only	The maximum value of round trip delay in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.10	Unsigned32	read-only	The average round trip delay in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.11	Unsigned32	read-only	The maximum value of round trip delay variation in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.12	Unsigned32	read-only	The average round trip delay variation in the selected interval. Values units are of 0.1 msec.
NUM ethOamSvcIntervalUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.13	PerfIntervalCount	read-only	The number of seconds that the service was unavailable in the selected interval.
ethOamSvcTotalTable	1.3.6.1.4.1.164.3.1.6.1.3.2.4		not-accessible	ETH OAM Service Total (24H) Statistics Table.
ethOamSvcTotalEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1		not-accessible	Total Statistics per service
PER ethOamSvcTotalFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.1	PerfTotalCount	read-only	Number of frames that arrived in a delay greater than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.2	PerfTotalCount	read-only	Number of frames that arrived in a delay lower than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.3	PerfTotalCount	read-only	Number of frames that arrived in a delay variation greater than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.4	PerfTotalCount	read-only	Number of frames that arrived in a delay variation lower than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.5	PerfTotalCount	read-only	Number of trnasmitted frames in the last 24H.
PER ethOamSvcTotalFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.6	PerfTotalCount	read-only	Number of lost frames in the last 24H.
U32 ethOamSvcTotalMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.7	Unsigned32	read-only	The mininal value of round trip delay in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.8	Unsigned32	read-only	The maximum value of round trip delay in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.9	Unsigned32	read-only	The average round trip delay in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.10	Unsigned32	read-only	The maximum value of round trip delay variation in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.11	Unsigned32	read-only	The average round trip delay variation in the last 24H. Values units are of 0.1 msec.
PER ethOamSvcTotalUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.12	PerfTotalCount	read-only	The number of seconds that the service was unavailable in the last 24H.
radMdTable	1.3.6.1.4.1.164.3.1.6.1.3.3		not-accessible	The MaintenanceDomain table. Each row in the table represents a different maintenance domain. A Maintenance domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance.
radMdEntry	1.3.6.1.4.1.164.3.1.6.1.3.3.1		not-accessible	The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage
U32 radMdIndex	1.3.6.1.4.1.164.3.1.6.1.3.3.1.1	Unsigned32	not-accessible	The index to the maintenance domain table.
INT radMdFormat	1.3.6.1.4.1.164.3.1.6.1.3.3.1.2	INTEGER	read-create	The type (and thereby format) of the Maintenance Domain Name.
OCT radMdName	1.3.6.1.4.1.164.3.1.6.1.3.3.1.3	OCTET STRING	read-create	The Maintenance Domain name. The type/format of this object is determined by the value of the radMdNameType object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain.
ROW radMdRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.3.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
radMepLtrTable	1.3.6.1.4.1.164.3.1.6.1.3.4		not-accessible	This table contains a list of Linktrace replies received by a specific MEP in response to a linktrace message.
radMepLtrEntry	1.3.6.1.4.1.164.3.1.6.1.3.4.1		not-accessible	The LinktraceReply table entry.
U32 radMepLtrReceiveOrder	1.3.6.1.4.1.164.3.1.6.1.3.4.1.1	Unsigned32	not-accessible	An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. radMepLtrReceiveOrder are assigned sequentially from 1, in the order that the Linktrace Initiator received the LTRs.
U32 radMepLtrTtl	1.3.6.1.4.1.164.3.1.6.1.3.4.1.2	Unsigned32	read-only	TTL field value for a returned LTR.
MAC radMepLtrMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.4.1.3	MacAddress	read-only	The MAC address in the header of the returned LTR.
INT radMepLtrRelay	1.3.6.1.4.1.164.3.1.6.1.3.4.1.4	INTEGER	read-only	The value returned in the Relay Action field: rlyHit - the LTM reached an MP whose MAC address matches the target MAC address. rlyFdb - the Egress Port was determined by consulting the Filtering Database. rlyMpdb - the Egress Port was determined by consulting the MIP CCM Database. 802.1ag clauses 12.14.7.5.3:g and 20.36.2.5
INT radMepLtrIngress	1.3.6.1.4.1.164.3.1.6.1.3.4.1.5	INTEGER	read-only	The value returned in the Ingress Action Field of the LTM. ingNoTlv - no Reply Ingress TLV was returned in the LTM. ingOK - the target data frame would be passed through to the MAC Relay Entity. ingDown - the Bridge Port's MAC_Operational parameter is false. ingBlocked - the target data frame would not be forwarded if received on this port. ingVid - the ingress port is not in the members of the LTM's VID, and ingress filtering is enabled, so the target data frame would be filtered by the ingress filtering. 802.1ag clauses 12.14.7.5.3:k and 20.36.2.6
LLD radMepLtrIngressPortIdSubtype	1.3.6.1.4.1.164.3.1.6.1.3.4.1.6	LldpPortIdSubtype	read-only	The format of the Ingress Port ID. If the radMepLtrIngress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:m and 20.36.2.8
OCT radMepLtrIngressPortId	1.3.6.1.4.1.164.3.1.6.1.3.4.1.7	OCTET STRING	read-only	Ingress Port ID. This is an alpha-numeric string that contains a specific identifier for the port. The format of this object is determined by the value of the radMepLtrIngressPortIdSubtype object. If the radMepLtrIngress object contains the value ingNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:n and 20.36.2.9
INT radMepLtrEgress	1.3.6.1.4.1.164.3.1.6.1.3.4.1.8	INTEGER	read-only	The value returned in the Egress Action Field of the LTM. The value egrNoTlv(1) indicates that no Reply Egress TLV was returned in the LTM. 802.1ag clauses 12.14.7.5.3:o and 20.36.2.10
LLD radMepLtrEgressPortIdSubtype	1.3.6.1.4.1.164.3.1.6.1.3.4.1.9	LldpPortIdSubtype	read-only	The format of the egress Port ID. If the radMepLtrEgress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:q and 20.36.2.12
OCT radMepLtrEgressPortId	1.3.6.1.4.1.164.3.1.6.1.3.4.1.10	OCTET STRING	read-only	Egress Port ID. The format of this object is determined by the value of the radMepLtrEgressPortIdSubtype object. If the radMepLtrEgress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:r and 20.36.2.13
radMepCcStatusTable	1.3.6.1.4.1.164.3.1.6.1.3.5		not-accessible	This table contains a list of CC Status received by a specific MEP from different Remote MEPs.
radMepCcStatusEntry	1.3.6.1.4.1.164.3.1.6.1.3.5.1		not-accessible	An entry in the CC Status Table.
U32 radMepRemoteMepIdx	1.3.6.1.4.1.164.3.1.6.1.3.5.1.1	Unsigned32	not-accessible	This is a running index for arriving CC messages (from different Remote MEPs) for a specific MEP ID.
U32 radMepCcStatusRemMepId	1.3.6.1.4.1.164.3.1.6.1.3.5.1.2	Unsigned32	read-create	This attribute indicates the Remote MEP ID from which the CC messages has arrived.
INT radMepCcStat	1.3.6.1.4.1.164.3.1.6.1.3.5.1.3	INTEGER	read-only	This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpectedMep -A MEP detects an Unexpected MEP condition when a CCM frame arrives with the correct MEG level, the correct MEG ID, but an unexpected MEP ID, which includes the MEP's own MEP ID. unexpectedMeLevel - A MEP detects an Unexpected MEG Level condition when a CCM frame arrives with incorrect MEG Level. Incorrect MEG Level is less than the MEP's own MEG level. unexpectedPeriod - A MEP detects an Unexpected Period condition when a CCM frame arrives with a correct MEG level. a correct MEG ID, a correct MEP ID, but with the Period field value different from the MEP's own CCM transmission period. rdi - A MEP detects RDI when it receives a CCM frame with the RDI field set.
MAC radMepCcStatusMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.5.1.4	MacAddress	read-only	This object indicates the MAC Address in the CC Status message received.
U32 ethOamStdEtherType	1.3.6.1.4.1.164.3.1.6.1.3.6	Unsigned32	read-write	The Standard Ether Type in an OAM message. This object will be RW until a formal value will be issued for standard Ethernet Type. When such Standard will exist, this object will be supported RO to reflect the Standard value.
MAC ethOamStdMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.7	MacAddress	read-write	The Standard MAC Address in an OAM message. This object will be RW until a formal value will be issued for standard MAC Address. When such Standard will exist, this object will be supported RO to reflect the Standard value.
dot1agXCfmMdTable	1.3.6.1.4.1.164.3.1.6.1.3.8		not-accessible	The Maintenance Domain table. Each row in the table represents a different maintenance association.
dot1agXCfmMdEntry	1.3.6.1.4.1.164.3.1.6.1.3.8.1		not-accessible	The Maintenance Domain table entry.
INT dot1agXCfmMdProtocol	1.3.6.1.4.1.164.3.1.6.1.3.8.1.1	INTEGER	read-create	.
dot1agXCfmMepTable	1.3.6.1.4.1.164.3.1.6.1.3.9		not-accessible	The Maintenance Association End Point (MEP) table.
dot1agXCfmMepEntry	1.3.6.1.4.1.164.3.1.6.1.3.9.1		not-accessible	The MEP table entry
INT dot1agXCfmMepContinuityVerMode	1.3.6.1.4.1.164.3.1.6.1.3.9.1.1	INTEGER	read-create	This object determines the OAM behavior of the MEP: disabled - no Continuity Verification is done cc_based - Continuity Verification is done based on incoming CC messages lb_based - Continuity Verification is done based on loopback messages.
INT dot1agXCfmMepDestAddrType	1.3.6.1.4.1.164.3.1.6.1.3.9.1.2	INTEGER	read-create	This object determines if the OAM messages are sent to user defined unicast address, or to RAD proprietary multicast address.
MAC dot1agXCfmMepDestMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.9.1.3	MacAddress	read-create	This object determines the MAC address that OAM packets are sent to.
dot1agXCfmMepDbTable	1.3.6.1.4.1.164.3.1.6.1.3.10		not-accessible	The MEP DB table
dot1agXCfmMepDbEntry	1.3.6.1.4.1.164.3.1.6.1.3.10.1		not-accessible	The MEP Database table entry.
INT dot1agXCfmMepCcStat	1.3.6.1.4.1.164.3.1.6.1.3.10.1.1	INTEGER	read-only	This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpectedMep -A MEP detects an Unexpected MEP condition when a CCM frame arrives with the correct MEG level, the correct MEG ID, but an unexpected MEP ID, which includes the MEP's own MEP ID. unexpectedMeLevel - A MEP detects an Unexpected MEG Level condition when a CCM frame arrives with incorrect MEG Level. Incorrect MEG Level is less than the MEP's own MEG level. unexpectedPeriod - A MEP detects an Unexpected Period condition when a CCM frame arrives with a correct MEG level. a correct MEG ID, a correct MEP ID, but with the Period field value different from the MEP's own CCM transmission period. rdi - A MEP detects RDI when it receives a CCM frame with the RDI field set.
ethIfRing	1.3.6.1.4.1.164.3.1.6.1.4
ethIfRingEvents	1.3.6.1.4.1.164.3.1.6.1.4.0
NTF ethIfRingStatusChange	1.3.6.1.4.1.164.3.1.6.1.4.0.1			This trap indicates that the status of the Ethernet Ring has been changed.
ethIfRingTable	1.3.6.1.4.1.164.3.1.6.1.4.1		not-accessible	Ethernet Ring Table.
ethIfRingEntry	1.3.6.1.4.1.164.3.1.6.1.4.1.1		not-accessible	An entry in the table.
U32 ethIfRingIdx	1.3.6.1.4.1.164.3.1.6.1.4.1.1.1	Unsigned32	not-accessible	This object is an Index that can indicate Slot, Ring, Cnfg etc., according to the device used. When NA, 1 will be used.
INT ethIfRingAdminStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.2	INTEGER	read-write	This object denotes the Ethernet Ring administrative status.
POR ethIfRingPorts	1.3.6.1.4.1.164.3.1.6.1.4.1.1.3	PortList	read-write	The set of ports which are assigned to be ring members. The default value of this object is a string of zeros.
INT ethIfRingOperStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.4	INTEGER	read-only	This object indicates the Ethernet Ring operational status.
U32 ethIfRingKeepAliveInterval	1.3.6.1.4.1.164.3.1.6.1.4.1.1.5	Unsigned32	read-write	This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
U32 ethIfRingKeepAliveThresh	1.3.6.1.4.1.164.3.1.6.1.4.1.1.6	Unsigned32	read-write	This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
U32 ethIfRingKeepAliveVlanId	1.3.6.1.4.1.164.3.1.6.1.4.1.1.7	Unsigned32	read-write	Dedicated VLAN ID for keep alive messages.
U32 ethIfRingMultiCastVlanId	1.3.6.1.4.1.164.3.1.6.1.4.1.1.8	Unsigned32	read-write	Dedicated VLAN ID for multicast messages.
INT ethIfRingRowStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.9	INTEGER	read-write	Implement creation/deletion of rings in the device.
ethIfStorming	1.3.6.1.4.1.164.3.1.6.1.5
ethIfStormTable	1.3.6.1.4.1.164.3.1.6.1.5.1		not-accessible	Ethernet Storming Table.
ethIfStormEntry	1.3.6.1.4.1.164.3.1.6.1.5.1.1		not-accessible	An entry in the table.
U32 ethIfStormCnfgIdx	1.3.6.1.4.1.164.3.1.6.1.5.1.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 ethIfStormIfIdx	1.3.6.1.4.1.164.3.1.6.1.5.1.1.2	Unsigned32	not-accessible	A unique index of the ethernet interface/port.
INT ethIfStormDirection	1.3.6.1.4.1.164.3.1.6.1.5.1.1.3	INTEGER	not-accessible	This object indicates the port's Storm Direction.
BIT ethIfStormPacketType	1.3.6.1.4.1.164.3.1.6.1.5.1.1.4	Bits	not-accessible	Packet Type on which Storming operations will be performed.
INT ethIfStormCtrlEnable	1.3.6.1.4.1.164.3.1.6.1.5.1.1.5	INTEGER	read-write	This object indicates if the Storm Controling is Enabled or Disabled for the relevant entry.
U32 ethIfStormMaxRate	1.3.6.1.4.1.164.3.1.6.1.5.1.1.6	Unsigned32	read-write	This object indicates the Maximum Rate at which Storming packets are forwarded, in Kbps.For some devices the units are PPS(Packets Per Second ) or kilobytes per second.
ethIfOamEfm	1.3.6.1.4.1.164.3.1.6.1.6
dot3OamEvents	1.3.6.1.4.1.164.3.1.6.1.6.0
NTF dot3OamOperStatusChange	1.3.6.1.4.1.164.3.1.6.1.6.0.1			This trap is sent when OAM EFM Link goes Up or Down. Up - is considered when dot3OamOperStatus value changes to operational(9) from any other value. Down - is considered when dot3OamOperStatus value changes from operational(9) to any other value.
NTF dot3OamPeerEvent	1.3.6.1.4.1.164.3.1.6.1.6.0.2			This trap is sent when value of dot3OamXPeerState changes from any value to one of the following values: linkFault, dyingGasp, criticalEvent. This trap has no recovery (clearing value).
dot3OamDescrTable	1.3.6.1.4.1.164.3.1.6.1.6.1		not-accessible	This table supports definitions of Descriptors (profiles) of OAM EFM Links.
dot3OamDescrEntry	1.3.6.1.4.1.164.3.1.6.1.6.1.1		not-accessible	Each entry corresponds to a single OAM EFM Descriptor (profile). Each Descriptor contains a set of OAM EFM Link configuration parameters. The configuration parameters are applied to the OAM EFM Links referencing this Descriptor (see dot3OamXDescrId object). Descriptors may be created/deleted using the row creation/deletion mechanism via dot3OamDescrRowStatus. If an active entry is referenced in dot3OamXDescrId, the entry MUST remain active until all references are removed.
U32 dot3OamDescrId	1.3.6.1.4.1.164.3.1.6.1.6.1.1.1	Unsigned32	not-accessible	This object is the unique index associated with this Descriptor (profile). Entries in this table are referenced via the object dot3OamXDescrId in dot3OamXEntry.
ROW dot3OamDescrRowStatus	1.3.6.1.4.1.164.3.1.6.1.6.1.1.2	RowStatus	read-create	This object controls creation/deletion of the associated entry in this table per the semantics of RowStatus. If an active entry is referenced in dot3OamXDescrId, the entry MUST remain active until all references are removed.
INT dot3OamDescrMode	1.3.6.1.4.1.164.3.1.6.1.6.1.1.3	INTEGER	read-create	This object controls the mode of OAM operation for an Ethernet-like interface referencing this Descriptor. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional capabilities to initiate monitoring activities with the remote OAM peer entity, while passive mode generally waits for the peer to initiate OAM actions with it. As an example, an active OAM entity can put the remote OAM entity in a loopback state, where a passive OAM entity cannot.
INT dot3OamDescrLbRxOperation	1.3.6.1.4.1.164.3.1.6.1.6.1.1.4	INTEGER	read-create	Since OAM loopback is a disruptive operation (user traffic does not pass), this object provides a mechanism to provide control: whether received OAM loopback commands are processed or ignored, for the OAM Link referencing this Descriptor. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), received loopback commands are processed. The default value is to ignore loopback commands (ignore(1)).
U32 dot3OamDescrRateLimit	1.3.6.1.4.1.164.3.1.6.1.6.1.1.5	Unsigned32	read-create	This object defines how many OAM frames can be sent per second (maximum) for an OAM EFM Link referencing this Descriptor.
dot3OamXTable	1.3.6.1.4.1.164.3.1.6.1.6.2		not-accessible	This table is an extension of dot3OamTable of standard DOT3-OAM-MIB.
dot3OamXEntry	1.3.6.1.4.1.164.3.1.6.1.6.2.1		not-accessible	An entry in dot3OamXTable.
U32 dot3OamXDescrId	1.3.6.1.4.1.164.3.1.6.1.6.2.1.1	Unsigned32	read-write	This object points to an entry of dot3OamDescrTable (dot3OamDescrId), which defines part of the configuration parameters for this OAM EFM Link. As long as one of the OAM EFM Links refers an entry in the dot3OamDescrTable, this entry cannot be removed. When an OAM EFM Link supports this object (RW), the standard MIB objects of: dot3OamMode (parallel to dot3OamDescrMode) and dot3OamLoopbackIgnoreRx (parallel to dot3OamDescrLbRxOperation) will be supported by Agent RO.
INT dot3OamXPeerState	1.3.6.1.4.1.164.3.1.6.1.6.2.1.2	INTEGER	read-only	This object reports the state of the Peer of the OAM EFM Link. unknown - at the initialization of the device, or after Reset, when there is still no data about the peer's state. operational - usually after unknown state, when device senses that peer is OK. linkFault - Loss of Signal is detected by the receiver. dyingGasp - Unrecoverable condition has occurred (e.g power failure) criticalEvent - Unspecified Critical Event has occured.
ethIfMacLayer	1.3.6.1.4.1.164.3.1.6.1.7
ethIfMacLayerEvents	1.3.6.1.4.1.164.3.1.6.1.7.0
NTF ethIfMacAccessViolation	1.3.6.1.4.1.164.3.1.6.1.7.0.1			This trap indicates that an Access Violation occurred.
ethIfSrcMacCtrlTable	1.3.6.1.4.1.164.3.1.6.1.7.1		not-accessible	This table supports source MAC addresses control parameters per interface. Source MAC control will be used mainly for security. Only packets with certain source MAC Addresses will be allowed to access the device. The source MAC addresses can be static or learned. The static addresses will be defined by the user in another table: ethIfSrcMacCtrlAddrTable. The learned addresses will exist in the ethIfSrcMacCtrlAddrTable as well.
ethIfSrcMacCtrlEntry	1.3.6.1.4.1.164.3.1.6.1.7.1.1		not-accessible	An entry in the table.
U32 ethIfSrcMacCtrlIndex	1.3.6.1.4.1.164.3.1.6.1.7.1.1.1	Unsigned32	not-accessible	The index of the MAC Layer interface supporting source MAC control feature. It may be the ifIndex of the ETH/Bridge Port.
U32 ethIfSrcMacCtrlIdx2	1.3.6.1.4.1.164.3.1.6.1.7.1.1.2	Unsigned32	not-accessible	A second index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.
INT ethIfSrcMacCtrl	1.3.6.1.4.1.164.3.1.6.1.7.1.1.3	INTEGER	read-write	Enable or disable the source MAC control on the current interface. The device should not enable source MAC control if for the current interface there are more than ethIfSrcMacCtrlMaxPermitAddr addresses in the ethIfSrcMacCtrlAddrTable. Default value will be: disable (2).
U32 ethIfSrcMacCtrlMaxPermitAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.4	Unsigned32	read-write	This is the maximum number of permitted MAC addresses (static and learned) for the current interface.
U32 ethIfSrcMacCtrlCurNumPermitAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.5	Unsigned32	read-only	This is the number of source MAC addresses currently permitted for the current interface.
INT ethIfSrcMacCtrlFlushAddrCmd	1.3.6.1.4.1.164.3.1.6.1.7.1.1.6	INTEGER	read-write	When set to on (3) this command will erase all the learned addresses and invalid addresses of the selected interface in the ethIfSrcMacCtrlAddrTable. After operation is finished, Agent will turn the value to 'off'.
U32 ethIfSrcMacCtrlAging	1.3.6.1.4.1.164.3.1.6.1.7.1.1.7	Unsigned32	read-write	The timeout period in seconds for aging out dynamically learned source MAC addresses. Valid Values: 0 - disable 10-1000000
INT ethIfSrcMacCtrlLocking	1.3.6.1.4.1.164.3.1.6.1.7.1.1.8	INTEGER	read-write	When set to lock (3) this command will lock the Source MAC Address learning. No more learned addresses will be added to the ethIfSrcMacCtrlAddrTable. When set to unlock (2) this command will unlock the Source MAC Address learning. Learned addresses will be added to the ethIfSrcMacCtrlAddrTable but the number of addresses in the table will not exceed ethIfSrcMacCtrlMaxPermitAddr. Default value is: unlock (2).
INT ethIfSrcMacCtrlViolationAction	1.3.6.1.4.1.164.3.1.6.1.7.1.1.9	INTEGER	read-write	Determines the action that the device will take upon security violation. drop(2) - the violating packets will be dropped. dropNotify (3)- the violating packets will be dropped and notifications will be generated. Notifications may be for example: SNMP Traps, Syslog messages and log file new entries. shutdown (4) - the interface will be forced to shut down.
MAC ethIfSrcMacCtrlLastViolatingAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.10	MacAddress	read-write	This object indicates the last MAC address that violated the security on the current interface. If no violation, the agent will return: 00-00-00-00-00-00 .
INT ethIfSrcMacCtrlPortStatus	1.3.6.1.4.1.164.3.1.6.1.7.1.1.11	INTEGER	read-only	This object represents the operational status of the MAC Control feature on an interface. shutdown(2) - This indicates that the port is shutdown due to security violation. secureActive (3) - This indicates that the MAC Control interface security is operational and this interface is not shutdown due to security violation. secureInactive (4)- This indicates that the MAC Control is not operational.
ethIfSrcMacCtrlAddrTable	1.3.6.1.4.1.164.3.1.6.1.7.2		not-accessible	This table shows which MAC Addresses are permitted when the source MAC control is enabled and which non permitted MAC Addresses attempted to access the current interface. It contains static source MAC Addresses as well as learned MAC Addresses. The user can configure Static permitted source MAC Addresses via this table.
ethIfSrcMacCtrlAddrEntry	1.3.6.1.4.1.164.3.1.6.1.7.2.1		not-accessible	An entry in the table.
U32 ethIfSrcMacCtrlAddrIndex	1.3.6.1.4.1.164.3.1.6.1.7.2.1.1	Unsigned32	not-accessible	The index of the interface for which the source MAC addresses exist in this table. It may be the ifIndex of the ETH/Bridge Port.
MAC ethIfSrcMacCtrlAddr	1.3.6.1.4.1.164.3.1.6.1.7.2.1.2	MacAddress	not-accessible	A unicast source MAC address that was learned or statically configured for the current interface. Packets with this source MAC address will be accepted by the device.
U32 ethIfSrcMacCtrlAddrIdx3	1.3.6.1.4.1.164.3.1.6.1.7.2.1.3	Unsigned32	not-accessible	A third index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.
INT ethIfSrcMacCtrlAddrRowStatus	1.3.6.1.4.1.164.3.1.6.1.7.2.1.4	INTEGER	read-write	This MIB object will be used in order to create/delete a static row or delete an address that is not allowed to access the current interface (ethIfSrcMacCtrlAddrStatus= invalid(2)). Device will add the learned addresses to this table. It will not be possible to add a new static entry to this table while the number of existing rows is equal or more than ethIfSrcMacCtrlMaxPermitAddr. When ethIfSrcMacCtrl = enabled (3), the device will add learned entries only up to ethIfSrcMacCtrlMaxPermitAddr.
INT ethIfSrcMacCtrlAddrStatus	1.3.6.1.4.1.164.3.1.6.1.7.2.1.5	INTEGER	read-only	The status of this entry. The meanings of the values are: invalid (2) - the current address is not allowed to access this interface. learned(3) - the current address was learned. mgmt (5) - the current address is static. It may exist in the MAC Table.
ds3Interface	1.3.6.1.4.1.164.3.1.6.3
prtDs3PerfHistory	1.3.6.1.4.1.164.3.1.6.3.1
prtSDs3IfTable	1.3.6.1.4.1.164.3.1.6.3.1.1		not-accessible	The DS3 interface table.
prtDs3IfEntry	1.3.6.1.4.1.164.3.1.6.3.1.1.1		not-accessible	An entry in the DS3 interface table.
I32 prtDs3IfTimeElapsed	1.3.6.1.4.1.164.3.1.6.3.1.1.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
I32 prtDs3IfValidIntervals	1.3.6.1.4.1.164.3.1.6.3.1.1.1.2	Integer32	read-only	The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
prtDs3CurrentTable	1.3.6.1.4.1.164.3.1.6.3.1.2		not-accessible	The DS3 Current table.
prtDs3CurrentEntry	1.3.6.1.4.1.164.3.1.6.3.1.2.1		not-accessible	An entry in the DS3 Current table.
G32 prtDs3CurrentLOS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.1	Gauge32	read-only	The counter associated with the number of LOS seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentOOF	1.3.6.1.4.1.164.3.1.6.3.1.2.1.2	Gauge32	read-only	The counter associated with the number of OOF seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentLOC	1.3.6.1.4.1.164.3.1.6.3.1.2.1.3	Gauge32	read-only	The counter associated with the number of LOC seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentAIS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.4	Gauge32	read-only	The counter associated with the number of AIS seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentRDI	1.3.6.1.4.1.164.3.1.6.3.1.2.1.5	Gauge32	read-only	The counter associated with the number of RDI seconds, encountered by a DS3 interface.
G32 prtDs3CurrentUAS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.6	Gauge32	read-only	The counter associated with the number of UAS, encountered by a SONET interface.
G32 prtDs3CurrentBIP	1.3.6.1.4.1.164.3.1.6.3.1.2.1.7	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentFEBE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.8	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentSLM	1.3.6.1.4.1.164.3.1.6.3.1.2.1.9	Gauge32	read-only	The counter associated with the number of SLM seconds, encountered by an E3 (only ) interface in the current 15 minute interval.
G32 prtDs3CurrentSES	1.3.6.1.4.1.164.3.1.6.3.1.2.1.10	Gauge32	read-only	The counter associated with the number of SES encountered by a E3 interface in the current 15 minute interval.
G32 prtDs3CurrentES	1.3.6.1.4.1.164.3.1.6.3.1.2.1.11	Gauge32	read-only	The number of Errored Seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentBitParity	1.3.6.1.4.1.164.3.1.6.3.1.2.1.12	Gauge32	read-only	Bit Parity Error counter. Relevant to T3 only.
G32 prtDs3CurrentPlcpLOF	1.3.6.1.4.1.164.3.1.6.3.1.2.1.13	Gauge32	read-only	The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configuration If frame types only.
G32 prtDs3CurrentPlcpRAI	1.3.6.1.4.1.164.3.1.6.3.1.2.1.14	Gauge32	read-only	Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentPlcpBIP	1.3.6.1.4.1.164.3.1.6.3.1.2.1.15	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentPlcpFEBE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.16	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentBPV	1.3.6.1.4.1.164.3.1.6.3.1.2.1.17	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the current 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.
G32 prtDs3CurrentLCE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.18	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the current 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.
OCT prtDs3CurrentStatus	1.3.6.1.4.1.164.3.1.6.3.1.2.1.19	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
prtDs3IntervalTable	1.3.6.1.4.1.164.3.1.6.3.1.3		not-accessible	The DS3 Interval table.
prtDs3IntervalEntry	1.3.6.1.4.1.164.3.1.6.3.1.3.1		not-accessible	An entry in the DS3 Interval table.
I32 prtDs3IntervalNumber	1.3.6.1.4.1.164.3.1.6.3.1.3.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 prtDs3IntervalLOS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.2	Gauge32	read-only	The counter associated with the number of LOS seconds , encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalOOF	1.3.6.1.4.1.164.3.1.6.3.1.3.1.3	Gauge32	read-only	The counter associated with the number of OOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalLOC	1.3.6.1.4.1.164.3.1.6.3.1.3.1.4	Gauge32	read-only	The counter associated with the number of LOC seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalAIS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.5	Gauge32	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalRDI	1.3.6.1.4.1.164.3.1.6.3.1.3.1.6	Gauge32	read-only	The counter associated with the number of RDI seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalUAS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.7	Gauge32	read-only	The counter associated with the number of UAS, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalBIP	1.3.6.1.4.1.164.3.1.6.3.1.3.1.8	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalFEBE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.9	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalSLM	1.3.6.1.4.1.164.3.1.6.3.1.3.1.10	Gauge32	read-only	The counter associated with the number of SLM seconds, encountered by an E3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalSES	1.3.6.1.4.1.164.3.1.6.3.1.3.1.11	Gauge32	read-only	The counter associated with the number of SES encountered by a E3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalES	1.3.6.1.4.1.164.3.1.6.3.1.3.1.12	Gauge32	read-only	The number of Errored Seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalBitParity	1.3.6.1.4.1.164.3.1.6.3.1.3.1.13	Gauge32	read-only	Bit Parity Error counter. Relevant to T3 only.
G32 prtDs3IntervalPlcpLOF	1.3.6.1.4.1.164.3.1.6.3.1.3.1.14	Gauge32	read-only	The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configuration If frame types only.
G32 prtDs3IntervalPlcpRAI	1.3.6.1.4.1.164.3.1.6.3.1.3.1.15	Gauge32	read-only	Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalPlcpBIP	1.3.6.1.4.1.164.3.1.6.3.1.3.1.16	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalPlcpFEBE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.17	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalBPV	1.3.6.1.4.1.164.3.1.6.3.1.3.1.18	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.
G32 prtDs3IntervalLCE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.19	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.
OCT prtDs3IntervalStatus	1.3.6.1.4.1.164.3.1.6.3.1.3.1.20	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
prtDs3TotalTable	1.3.6.1.4.1.164.3.1.6.3.1.4		not-accessible	A list of Total entries.
prtDs3TotalEntry	1.3.6.1.4.1.164.3.1.6.3.1.4.1		not-accessible	An entry of Total table.
G32 prtDs3TotalUAS	1.3.6.1.4.1.164.3.1.6.3.1.4.1.6	Gauge32	read-only	Number of UASs (Unavailable Seconds) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
G32 prtDs3TotalBPV	1.3.6.1.4.1.164.3.1.6.3.1.4.1.17	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
G32 prtDs3TotalLCE	1.3.6.1.4.1.164.3.1.6.3.1.4.1.18	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
G32 prtDs3TotalSES	1.3.6.1.4.1.164.3.1.6.3.1.4.1.19	Gauge32	read-only	Number of SES (Severely Errored Seconds) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
dsx3XConfigTable	1.3.6.1.4.1.164.3.1.6.3.2		not-accessible	An extension to the DS3 Configuration table.
dsx3XConfigEntry	1.3.6.1.4.1.164.3.1.6.3.2.1		not-accessible	An entry containing additional configuration parameters.
INT dsx3AisEnable	1.3.6.1.4.1.164.3.1.6.3.2.1.1	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet (for TDMoIP) line is disconnected.
INT dsx3TxClockSource	1.3.6.1.4.1.164.3.1.6.3.2.1.2	INTEGER	read-write	The source of Transmit Clock. loopTiming indicates that the recovered receive clock is used as the transmit clock. localTiming indicates that a local clock source is used or that an external clock is attached to the box containing the interface. throughTiming indicates that transmit clock is derived from the recovered receive clock of another DS3 interface. 'system' indicates that the system clock is used as the transmit clock.
dsx3MappingTable	1.3.6.1.4.1.164.3.1.6.3.3		not-accessible	The DS3/E3 mapping table associates DS3/E3 channels with logical or physical interfaces. For example, consider a DS3 device with 16 T1's and 1 VCG. There are 28 logical/internal channels, numbered 1 through 28 but only 17 are actually connected. We might describe the allocation of channels, in the dsx3MappingTable, as follows: dsx3MappingIfIndex.1. 1 = 1001 dsx3MappingIfIndex.1.15 = 1015 dsx3MappingIfIndex.1. 2 = 1002 dsx3MappingIfIndex.1.16 = 1016 dsx3MappingIfIndex.1. 3 = 1003 dsx3MappingIfIndex.1.17 = 1017 dsx3MappingIfIndex.1. 4 = 1004 dsx3MappingIfIndex.1.18 = 0 dsx3MappingIfIndex.1. 5 = 1005 dsx3MappingIfIndex.1.19 = 0 dsx3MappingIfIndex.1. 6 = 1006 dsx3MappingIfIndex.1.20 = 0 dsx3MappingIfIndex.1. 7 = 1007 dsx3MappingIfIndex.1.21 = 0 dsx3MappingIfIndex.1. 8 = 1008 dsx3MappingIfIndex.1.22 = 0 dsx3MappingIfIndex.1. 9 = 1009 dsx3MappingIfIndex.1.23 = 0 dsx3MappingIfIndex.1.10 = 1010 dsx3MappingIfIndex.1.24 = 0 dsx3MappingIfIndex.1.11 = 1011 dsx3MappingIfIndex.1.25 = 0 dsx3MappingIfIndex.1.12 = 1012 dsx3MappingIfIndex.1.26 = 0 dsx3MappingIfIndex.1.13 = 1013 dsx3MappingIfIndex.1.27 = 0 dsx3MappingIfIndex.1.14 = 1014 dsx3MappingIfIndex.1.28 = 0 Note that in the case above all channels are mapped to one T3 port with ifIndex = 1. The Channels 1...28 are represented via the 2nd index. The values of 1001...1016 are the T1 interface ifIndexes. The value of 1017 is the ifIndex of the VCG. Unconnected channels have a value of 0.
dsx3MappingEntry	1.3.6.1.4.1.164.3.1.6.3.3.1		not-accessible	An entry in the DS3 mapping table.
NUM dsx3MappingDs3Index	1.3.6.1.4.1.164.3.1.6.3.3.1.1	InterfaceIndex	not-accessible	The index value which uniquely identifies the DS3/E3 interface to which this entry is applicable. This value is also equal to dsx3LineIndex used in dsx3ConfigEntry. For RICi-16 this is the ifIndex of the T3 interface.
U32 dsx3MappingNumber	1.3.6.1.4.1.164.3.1.6.3.3.1.2	Unsigned32	not-accessible	The channel number for this entry. For RICi-16 this is the channel number 1...28.
NUM dsx3MappingIfIndex	1.3.6.1.4.1.164.3.1.6.3.3.1.3	InterfaceIndex	read-write	An index value that uniquely identifies a logical or physical interface mapped to a DS3/E3 channel. If no interface is currently using a channel, the value should be zero. If a single interface occupies more than one channel, that ifIndex value will be found in multiple channels. For RICi-16 this is the ifIndex of the T1 or VCG interface.
ds1Interface	1.3.6.1.4.1.164.3.1.6.4
prtDS1Events	1.3.6.1.4.1.164.3.1.6.4.0
NTF ds1LocalMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.1			This trap indicates near end (Local) Loss of Multiframe Alignment, of the user E1 interface.
NTF ds1RemoteMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.2			This trap indicates that the far end (remote) unit, connected to the user E1 interface, reports Loss of Multiframe Alignment.
NTF ds1LinkFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.3			This trap indicates that a Frame Slip occurred at the user DS1 interface. This usually indicates timing problems (incorrect selection of timing reference), on the user DS1 link.
NTF ds1BpvErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.4			This trap indicates a Bipolar Violation (BPV) error has been detected at the user DS1 interface.
NTF ds1ExcessiveBpvTrap	1.3.6.1.4.1.164.3.1.6.4.0.5			This trap indicates excessive number of Bipolar Violation errors (BPV) detected by the user DS1 interface
NTF ds1Crc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.6			This trap indicates that a frame with CRC-4 error has been detected at the user DS1 interface.
NTF ds1ExcessiveErrorRatioTrap	1.3.6.1.4.1.164.3.1.6.4.0.7			This trap indicates that the error rate, detected at the user DS1 interface, on the frame synchronization bits is high, as defined by ITU-T Rec. G.732.
NTF ds1RemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.8			This trap indicates that the far-end (remote) unit, connected to user DS1 interface, reports Loss of Frame Alignment (Sync Loss).
NTF ds1LocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.9			This trap indicates near end (Local) Loss of Frame Alignment failure (Sync Loss), of the user DS1 interface
NTF ds1AisSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.10			This trap indicates near end (Local) Loss of Frame Alignment (Sync Loss), caused by the reception of AIS at the user DS1 interface.
NTF ds1AisTrap	1.3.6.1.4.1.164.3.1.6.4.0.11			This trap indicates AIS being received at the user DS1 interface.
NTF ds1NetworkRemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.12			This trap indicates that a remote loopback has been activated, on the local uplink interface.
NTF ds1RemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.13			This trap indicates that a remote loopback has been activated, on the local user port.
NTF ds1LocalLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.14			This trap indicates that a local loopback has been activated on the user port.
NTF ds1ExcessiveFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.15			This trap indicates that the number of Frame Slips detected at the user DS1 interface, during the last minute exceeds threshold. For LA-110, threshold value is 10. This usually indicates timing problems (incorrect selection of timing reference) on the user DS1.
NTF ds1ExcessiveCrc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.16			This trap indicates that the error rate detected on the CRC-4 bits at the user DS1 interface, is high.
NTF ds1ExcessiveLocalMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.17			This trap indicates that the number of local Loss of Multiframe Alignment events, detected at the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.18			This trap indicates that the number of Loss of multiframe alignment events reported by the remote unit connected to the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.19			This trap indicates that the number of far end (remote) Loss of Synchronization alarms, reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveLocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.20			This trap indicates that the number of Loss of local Synchronization alarms reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
NTF ds1SignalLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.21			This trap indicates Signal Loss. (possible reason - cable disconnection. etc.)
prtDs1PerfHistory	1.3.6.1.4.1.164.3.1.6.4.1
dsx1XCurrentTable	1.3.6.1.4.1.164.3.1.6.4.1.2		not-accessible	A list of current statistics entries. This table contains additional objects for the current table.
dsx1XCurrentEntry	1.3.6.1.4.1.164.3.1.6.4.1.2.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
PER dsx1CurrentLOS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.1	PerfCurrentCount	read-only	The counter associated with the number of LOS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.2	PerfCurrentCount	read-only	The counter associated with the number of LOF seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.3	PerfCurrentCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
PER dsx1CurrentAIS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.4	PerfCurrentCount	read-only	The counter associated with the number of AIS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentRAI	1.3.6.1.4.1.164.3.1.6.4.1.2.1.5	PerfCurrentCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
PER dsx1CurrentLOMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.6	PerfCurrentCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
PER dsx1CurrentFEBE	1.3.6.1.4.1.164.3.1.6.4.1.2.1.7	PerfCurrentCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in the current 15 minute interval.
OCT dsx1CurrentStatus	1.3.6.1.4.1.164.3.1.6.4.1.2.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
PER dsx1CurrentBPV	1.3.6.1.4.1.164.3.1.6.4.1.2.1.9	PerfCurrentCount	read-only	The counter associated with the number of BPVs (Bi-Polar Violations) encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.10	PerfCurrentCount	read-only	Loss of CRC4 Multi-Frame sequence in E1. encountered in the current 15 minute interval
PER dsx1CurrentLOFC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.11	PerfCurrentCount	read-only	Counts the number of loss of frame events measured. encountered in the current 15 minute interval
PER dsx1CurrentCRCErrors	1.3.6.1.4.1.164.3.1.6.4.1.2.1.12	PerfCurrentCount	read-only	Counts the number of CRC error events, encountered in the current 15 minute interval.
dsx1XIntervalTable	1.3.6.1.4.1.164.3.1.6.4.1.3		not-accessible	A list of Interval entries. This table contains additional objects for the interval table.
dsx1XIntervalEntry	1.3.6.1.4.1.164.3.1.6.4.1.3.1		not-accessible	An entry containing additional statistical counters applicable to a particular interval table.
NUM dsx1IntervalLOS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.1	PerfIntervalCount	read-only	The counter associated with the number of LOS seconds , encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.2	PerfIntervalCount	read-only	The counter associated with the number of OOF seconds, encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.3	PerfIntervalCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
NUM dsx1IntervalAIS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.4	PerfIntervalCount	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalRAI	1.3.6.1.4.1.164.3.1.6.4.1.3.1.5	PerfIntervalCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
NUM dsx1IntervalLOMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.6	PerfIntervalCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
NUM dsx1IntervalFEBE	1.3.6.1.4.1.164.3.1.6.4.1.3.1.7	PerfIntervalCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in one of the previous 96, individual, 15 minute intervals.
OCT dsx1IntervalStatus	1.3.6.1.4.1.164.3.1.6.4.1.3.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
NUM dsx1IntervalBPV	1.3.6.1.4.1.164.3.1.6.4.1.3.1.9	PerfIntervalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.10	PerfIntervalCount	read-only	Loss of CRC4 Multi-Frame sequence in E1.
NUM dsx1IntervalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.11	PerfIntervalCount	read-only	Counts the number of loss of frame events measured in one of the previous 96, individual 15 minute, intervals.
dsx1XTotalTable	1.3.6.1.4.1.164.3.1.6.4.1.4		not-accessible	A list of Total statistics entries. This table contains additional objects for the Total table.
dsx1XTotalEntry	1.3.6.1.4.1.164.3.1.6.4.1.4.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
PER dsx1TotalLOS	1.3.6.1.4.1.164.3.1.6.4.1.4.1.1	PerfTotalCount	read-only	The counter associated with the number of LOS (Loss of Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalBPV	1.3.6.1.4.1.164.3.1.6.4.1.4.1.9	PerfTotalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.4.1.11	PerfTotalCount	read-only	The counter associated with the number loss of frames encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
dsx1DataStreamStatTable	1.3.6.1.4.1.164.3.1.6.4.1.5		not-accessible	The DS1 Data Stream Statistics table.
dsx1DataStreamStatEntry	1.3.6.1.4.1.164.3.1.6.4.1.5.1		not-accessible	An entry in the DS1 Data Stream Statistics table.
I32 dsx1DataStreamStatIfIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.1	Integer32	not-accessible	The index of the DS1 interface. It may be ifIndex.
I32 dsx1DataStreamStatIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.2	Integer32	not-accessible	The DS1 Data Stream Index. For Vmux - the following indices are used: 1 for Transparent 2-3 for SS71-SS72 (respectively) 4-7 for Data1-Data4 (respectively) 8 for HDLC Ph2 Compatible 9-16 for Sub-CH1-1...Sub-CH1-8 (respectively).
T/F dsx1DataStreamStatValid	1.3.6.1.4.1.164.3.1.6.4.1.5.1.3	TruthValue	read-only	Indicates whether this Data Stream is valid or not. When invalid - all counters are irrelevant.
C32 dsx1DataStreamStatInFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.4	Counter32	read-only	The counter associated with the number of received frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.5	Counter32	read-only	The counter associated with the number of received bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.6	Counter32	read-only	The counter associated with the number of Discarded incoming frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.7	Counter32	read-only	The counter associated with the number of received Errored frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.8	Counter32	read-only	The counter associated with the number of transmitted frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.9	Counter32	read-only	The counter associated with the number of transmitted bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.10	Counter32	read-only	The counter associated with the number of Discarded outgoing frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.11	Counter32	read-only	The counter associated with the number of errored transmitted frames, encountered by the DS1 Data Stream.
dsx1XConfigTable	1.3.6.1.4.1.164.3.1.6.4.2		not-accessible	An extension to the DS1 Configuration table.
dsx1XConfigEntry	1.3.6.1.4.1.164.3.1.6.4.2.1		not-accessible	An entry containing additional configuration parameters.
I32 dsx1IdleCode	1.3.6.1.4.1.164.3.1.6.4.2.1.1	Integer32	read-write	Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).
INT dsx1LineMode	1.3.6.1.4.1.164.3.1.6.4.2.1.2	INTEGER	read-write	T1 device operation mode. Valid for T1 only.
INT dsx1dBTxGain	1.3.6.1.4.1.164.3.1.6.4.2.1.3	INTEGER	read-write	Transmit line Gain for T1 CSU line mode.
INT dsx1RxSensitivity	1.3.6.1.4.1.164.3.1.6.4.2.1.4	INTEGER	read-write	Low Sensitivity is considered Short Haul while High Sensitivity is considered Long Haul. The actual values depend on the LIU. Examples: - E1: -12dB is considered Short Haul ; -43dB is considered Long Haul - T1: -12dB is considered Short Haul ; -36dB is considered Long Haul.
INT dsx1RestoreTime	1.3.6.1.4.1.164.3.1.6.4.2.1.5	INTEGER	read-write	Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = CCITT
I32 dsx1TcFirstSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.6	Integer32	read-write	Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used also for Space Signaling Code (in this case 0xFF is not NULL).
I32 dsx1TcSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.7	Integer32	read-write	Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).
I32 dsx1TcPattern	1.3.6.1.4.1.164.3.1.6.4.2.1.8	Integer32	read-write	Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.
INT dsx1Scramble	1.3.6.1.4.1.164.3.1.6.4.2.1.9	INTEGER	read-write	Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicable for E1. active - will scramble/descramble the payload ATM cell notActive - will not scramble/descramble.
INT dsx1LineAdaptiveTimingMode	1.3.6.1.4.1.164.3.1.6.4.2.1.10	INTEGER	read-write	Enables end to end clock synchronization. Default value - off.
INT dsx1TxClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.11	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered receive clock from another interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'system' indicates that the system clock is used as the transmit clock.
INT dsx1AisEnable	1.3.6.1.4.1.164.3.1.6.4.2.1.12	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).
OCT dsx1TsEchoCancel	1.3.6.1.4.1.164.3.1.6.4.2.1.13	OCTET STRING	read-write	This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., 4th octet bit'7' = TS#32. Octets and bits order is from left to right: [31,30,..24] [23..16] [15..8] [7..0] MSB LSB MSB LSB MSB LSB MSB LSB For each bit values are: 0 - Echo-Cancellation off. 1 - Echo-Cancellation on.
INT dsx1EchoCancelerModule	1.3.6.1.4.1.164.3.1.6.4.2.1.14	INTEGER	read-only	This parameter indicates whether echo-cancellation module exists for this line.
INT dsx1PortFunction	1.3.6.1.4.1.164.3.1.6.4.2.1.15	INTEGER	read-write	This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as an IMA-ATM. cesPsn - The port will function as a CES-PSN. abis - The port will function as an Abis.
INT dsx1PortMultiplier	1.3.6.1.4.1.164.3.1.6.4.2.1.16	INTEGER	read-write	This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.
INT dsx1LeasedLine	1.3.6.1.4.1.164.3.1.6.4.2.1.17	INTEGER	read-write	This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).
INT dsx1CsuLoop	1.3.6.1.4.1.164.3.1.6.4.2.1.18	INTEGER	read-write	This parameter defines where the CSU loop will be done: local - locally (by IPmux) towards the TDM device transparent - transferred to Remote Device that will send it to its connected TDM device. remote - Remote Device will close the loop towards the Local Device.
I32 dsx1ClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.19	Integer32	read-write	This entry specifies the source from which the clock will be taken. Refer to device specification for source Index
INT dsx1OosSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.20	INTEGER	read-write	This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. 'Mark' = both A and B signaling bits are forced to '1' during out-of-service periods. 'spaceMark' = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. 'markSpace' = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. - '0'= 0 for T1, 1 for E1, or user defined value for Space - '1'= 1 for T1, 0 for E1, or user defined value for Mark.
I32 dsx1BundleNextIndex	1.3.6.1.4.1.164.3.1.6.4.2.1.21	Integer32	read-only	This parameter indicates the Next free Bundle Index for this DS1 port.
INT dsx1CRC6CalcMode	1.3.6.1.4.1.164.3.1.6.4.2.1.22	INTEGER	read-write	This object determines the CRC6 Calculation mode. jtG704 =JT-G704 = the Japanese standard ituG704=ITU-G704 = the International standard This parameter is applicable for J1 only.
INT dsx1SendUponFail	1.3.6.1.4.1.164.3.1.6.4.2.1.23	INTEGER	read-write	This object determines which notification will be sent to the other side upon fail of another interface. In Ipmux14 the notification is sent upon failure of the Ethernet link.
ip2If	1.3.6.1.4.1.164.3.1.6.7
ip2IfTable	1.3.6.1.4.1.164.3.1.6.7.1		not-accessible	Channels Configuration Table.
ip2IfEntry	1.3.6.1.4.1.164.3.1.6.7.1.1		not-accessible	Application layer configuration per link
I32 ip2IfChannelIndex	1.3.6.1.4.1.164.3.1.6.7.1.1.1	Integer32	read-only	The channel index, which is actualy the bundle ID.
ROW ip2IfRowStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.2	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table.
INT ip2IfOperStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.3	INTEGER	read-only	The actual link status. remoteFail - No Rx. localFail - No Tx. unavailable - No echo replay or replay with invalid code or when connection is in Test state. valiodationFail - Connection is in not valid state. standby - offline (can be in pre-sync mode). tdmFail - oper status is down cause of failure in the tdm. hwMismatch - the bundle exists on a card that is not installed or has a different type than the programmed card.
INT ip2IfAdminStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.4	INTEGER	read-create	The desired state of the link.
IP ip2IfDestAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.5	IpAddress	read-create	The destination IP address.
IP ip2IfNextHop	1.3.6.1.4.1.164.3.1.6.7.1.1.6	IpAddress	read-create	The next hop to which the frame should be sent. Default value - 0.0.0.0. Upon setting the default value the frame is sent to the default Gateway.
I32 ip2IfDestPort	1.3.6.1.4.1.164.3.1.6.7.1.1.7	Integer32	read-create	The destination Bundle at the far-end device.
MAC ip2IfMacAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.8	MacAddress	read-create	The Destination MAC address of the next hop or destination station.
I32 ip2IfJitterBuffer	1.3.6.1.4.1.164.3.1.6.7.1.1.9	Integer32	read-create	The maximum cell arrival jitter in 10 usec that the reassembly process will tolerate in the cell stream, without producing errors on the CBR service interface. For KM2100: KML.11 - The range that will be used is 3...300 msec in steps of 1 msec. For Vmux: The range that will be used is 20...100 msec in steps of 10 msec.
I32 ip2IfTos	1.3.6.1.4.1.164.3.1.6.7.1.1.10	Integer32	read-create	The TOS (Type of Service) value: 0..255. In Vmux-2100/110 devices versions 3.1 and up, in Vmux-210 and in Vmux-4x0: LSB 8 bits - 00 00 00 XX will be used for Signaling packets TOS. Next 8 bits - 00 00 XX 00 will be used for Media packets TOS. Next 16 bits - will be 0. XX = Hex values: 0..FF For mixed packets, TOS of Media Packets will be used. Signaling packets are for example: Keep alive packets and ABCD signaling bits. Media packets are for example: voice, fax, HDLC, payload packets.
I32 ip2IfTDMBytesInFrame	1.3.6.1.4.1.164.3.1.6.7.1.1.11	Integer32	read-create	The number of TDM bytes to be placed in a single IP frame payload. For ip2IfTDMoIpMode = cesOverPsn this parameter indicates the number of IP frames, calculated as: 1440/.
INT ip2IfVlanSupport	1.3.6.1.4.1.164.3.1.6.7.1.1.12	INTEGER	read-create	VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
I32 ip2IfVlanIdentifier	1.3.6.1.4.1.164.3.1.6.7.1.1.13	Integer32	read-create	VLAN ID.
I32 ip2IfVlanFramePriority	1.3.6.1.4.1.164.3.1.6.7.1.1.14	Integer32	read-create	VLAN Frame priority.
INT ip2IfExitPort	1.3.6.1.4.1.164.3.1.6.7.1.1.15	INTEGER	read-create	This object determines to which external port the traffic will be sent. auto - the device will decide automatically the exit port. If there is an option for Tx via more than one ETH card then use ext1 (1) and ext2(2) for ETH card #1 (ex. LAN1 or Ggabit-ETH1) and use card2Ext1(5) and card2Ext2(6) for card #2 (ex. LAN1 or Ggabit-ETH1). In Vmux-110/210 ext5 is used for ETH-NET, ext 6 is used for E1/T1 link and ext7 is used for Serial Link. In Vmux-2100 Main Board: ext 5 is used for ETH-NET, ext 6 is used for E1/T1 link A, prtE1T1B is used for E1/T1 link B and prtEthUser is used for ETH-User. prt17(10) - prt20(13) values were added in order to support Gmux2000 VMX Card.
OCT ip2IfVoiceOos	1.3.6.1.4.1.164.3.1.6.7.1.1.16	OCTET STRING	read-create	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT ip2IfDataOos	1.3.6.1.4.1.164.3.1.6.7.1.1.17	OCTET STRING	read-create	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
I32 ip2IfBundleUsage	1.3.6.1.4.1.164.3.1.6.7.1.1.18	Integer32	read-only	The Bundle Resource usage in Kbps.
OCT ip2IfOAM	1.3.6.1.4.1.164.3.1.6.7.1.1.19	OCTET STRING	read-create	This parameter determine the OAM configuration. The LSB (Bit 0 the most right one) is used for OAM connectivity. Values: 0 = disable, 1= enable.
INT ip2IfTDMoIpMode	1.3.6.1.4.1.164.3.1.6.7.1.1.20	INTEGER	read-create	The TDMoIP Mode configuration. Static- means TS can Tx any time. dynamicLES - means TS can Tx only when line is enabled according to LES protocol. dynamicCAS - means TS can Tx only when line is enabled according to CAS protocol. cesOverIp - use for information that this bundle is used for CES Over IP. voiceOverMpls - Voice over Multi Protocol Label Switching. hdlc - High Level Data Link. voIpComprHeader - indicates proprietary compressed IP header packets. voMplsComprHeader - indicates proprietary compressed MPLS header packets.
I32 ip2IfTimeElapsed	1.3.6.1.4.1.164.3.1.6.7.1.1.21	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
I32 ip2IfValidIntervals	1.3.6.1.4.1.164.3.1.6.7.1.1.22	Integer32	read-only	The number of previous intervals for which data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute intervals since the interface has been online.
INT ip2IfFarEndType	1.3.6.1.4.1.164.3.1.6.7.1.1.23	INTEGER	read-create	This object defines the type of the Far-End device. This data is important for signaling and DS0 format. For Vmux: e1 (2) value is used for a PBX in the Far End. fxs (5) is used for Phone. Other values are not used.
INT ip2IfRdnState	1.3.6.1.4.1.164.3.1.6.7.1.1.24	INTEGER	read-only	This object defines the role this bundle plays in the redundancy scheme: none(2) - means this bundle is not part of redundancy pair. primary/ secondary - means this bundle is not part of redundancy pair, and that is the primary bundle or the secondary bunle.
IP ip2IfSourceAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.25	IpAddress	read-create	Source IP Address of the bundle.
I32 ip2IfBandWidth	1.3.6.1.4.1.164.3.1.6.7.1.1.26	Integer32	read-create	Defines the Bandwidth of the bundle. For TDM bundles - it is the Number of Time Slots in The Bundle. - For T1 the value will be: 1..24 - For E1 the value will be: 1..31 - For T3 the value will be: 1..84 - For E3 the value will be: 1..63 This parameter is required for devices like Emux where the bandwidth of the bundles is unknown. The bundles that are received should be transmitted without any change in the bandwidth. It is the user's responsibility to enter the correct bandwidth. For Ethernet bundles - it is the bandwidth, measured in Kbps.
I32 ip2IfMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.1.1.27	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
INT ip2IfPayloadType	1.3.6.1.4.1.164.3.1.6.7.1.1.28	INTEGER	read-create	This object defines the TDMoIP payload type.
INT ip2IfProtocolVersion	1.3.6.1.4.1.164.3.1.6.7.1.1.29	INTEGER	read-create	This object defines the TDMoIP protocol Version.
IP ip2IfTdmBackUpNextHop	1.3.6.1.4.1.164.3.1.6.7.1.1.30	IpAddress	read-create	Defines the TDM bundle default router in case there was a switch from the Primary Link (for example an ETH port) to a TDM backup Link like E1, T1 or Serial Link. This parameter is relevant only when a Backup Link is configured. When a Backup Link is not configured the value will be: 0.0.0.0
INT ip2IfOosTxEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.31	INTEGER	read-create	This object defines whether OOS will be Transmitted. Note that for IPmux1000 the Lbit is always sent, but the OOS will be sent according to user selection in this parameter.
I32 ip2IfConnCheckPktFrequency	1.3.6.1.4.1.164.3.1.6.7.1.1.32	Integer32	read-create	Time in sec. between 2 Bundle Connectivity Check packets. Valid values: 0..60. 0 = Not Applicable.
I32 ip2IfConnPktTimeOutCycles	1.3.6.1.4.1.164.3.1.6.7.1.1.33	Integer32	read-create	No. of cycles the agent will send Bundle Connectivity packets without receiving a response from the remote device before declaring that the bundle connection to the remote side is down - Time Out. Valid values: 0..5. 0 = Not Applicable.
INT ip2IfMfRelay	1.3.6.1.4.1.164.3.1.6.7.1.1.34	INTEGER	read-create	Multi Frequency Signaling Detection.
I32 ip2IfTxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.35	Integer32	read-create	Transmit gain in dBm.
INT ip2IfSuperTandem	1.3.6.1.4.1.164.3.1.6.7.1.1.36	INTEGER	read-create	The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem allows transmission of compressed voice between a few Vmux 2100 hubs, and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay.
I32 ip2IfSrcPort	1.3.6.1.4.1.164.3.1.6.7.1.1.37	Integer32	read-create	The source Bundle at the local device, this parameter used for cases where there is no match between ip2IfChannelIndex and the Source Bundle ID.
INT ip2IfModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.38	INTEGER	read-create	This MIB object shows whether Modem Calls are enabled via the bundle. relay option (3) means that the bundle will send to the network only modulated data.
I32 ip2IfMinPulseWidth	1.3.6.1.4.1.164.3.1.6.7.1.1.39	Integer32	read-create	Indicates the minimum width in milliseconds of the MF (Multi Frequency) tone transmitted by the switch. Valid values: 45-300 msec. notApplicable=0.
I32 ip2IfMinPowerLevel	1.3.6.1.4.1.164.3.1.6.7.1.1.40	Integer32	read-create	Indicates the minimum power level in dBm of the MF (Multi Frequency) tone transmitted by the switch. Valid values: -1...-35 dBm.
INT ip2IfEchoCanceler	1.3.6.1.4.1.164.3.1.6.7.1.1.41	INTEGER	read-create	Echo canceler activation.
INT ip2IfCodingLaw	1.3.6.1.4.1.164.3.1.6.7.1.1.42	INTEGER	read-create	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links.
INT ip2IfCustomToneDetect	1.3.6.1.4.1.164.3.1.6.7.1.1.43	INTEGER	read-create	Custom Tone Detection (COT) is a Control operation of a 2Khz tone detector. This tone is sent between PBX devices in order to check that the line status is OK. When the COT is enabled the device will not compress/decompress the tone. In this case, if the tone is initiated by the local PBX, the Device runs a 2Khz detector tone and once detected by the Remote Device, if the COT is enabled in the Remote Device, the Remote Device will generate a 2khz tone to the remote PBX.
I32 ip2IfCallerIdDelay	1.3.6.1.4.1.164.3.1.6.7.1.1.44	Integer32	read-create	Time in msec between CLID (Caller ID) signal detection on the line and CLID signal transmission. The CLID must be sent between ringing signals and the value of the delay is used for synchronizing the CLID transmission with the ringing signals transmission. Valid values: 0 - 3000 msec.
INT ip2IfConnectivityMode	1.3.6.1.4.1.164.3.1.6.7.1.1.45	INTEGER	read-create	This MIB object shows whether to send Pings or OAM frames over the bundle.
INT ip2IfClockSourceEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.46	INTEGER	read-create	This MIB object defines whether this bundle can be a clock source.
INT ip2IfNetworkType	1.3.6.1.4.1.164.3.1.6.7.1.1.47	INTEGER	read-create	This MIB object defines the network over which the Bundle PSN (Packet Switching Network)is transported. In Gmux2000: ipComprHeader indicates proprietary compressed IP header packets. mplsComprHeader indicates proprietary compressed MPLS header packets.
INT ip2IfMplsRxLabelEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.48	INTEGER	read-create	This MIB object defines whether there is user defined inner (Rx.) label for this Bundle.
I32 ip2IfMplsRxLabel	1.3.6.1.4.1.164.3.1.6.7.1.1.49	Integer32	read-create	This MIB object defines the MPLS Rx. Label for this Bundle.
INT ip2IfMplsTxLabelEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.50	INTEGER	read-create	This MIB object defines whether there is user defined outer (Tx.) label for this Bundle.
I32 ip2IfMplsTxLabel	1.3.6.1.4.1.164.3.1.6.7.1.1.51	Integer32	read-create	This MIB object defines the MPLS Tx. Label for this Bundle.
I32 ip2IfMplsTxExpBits	1.3.6.1.4.1.164.3.1.6.7.1.1.52	Integer32	read-create	The MPLS Network priority (EXP bits) used for this bundle.
INT ip2IfMfcSpoofing	1.3.6.1.4.1.164.3.1.6.7.1.1.53	INTEGER	read-create	This MIB object defines whether the MFC (Multi Frequency Compelled) protocol spoofing will exist in the bundle. When the MFC Spoofing is used, the Local and Remote PBXs will send MFC Signaling to each other. The Vmuxes between the PBXs will send proprietary signaling to each other. They will however create and send MFC tones to their local PBX. The PBXs will not know that the actual signaling was not sent from a PBX but from a Vmux.
I32 ip2IfToneAckInterval	1.3.6.1.4.1.164.3.1.6.7.1.1.54	Integer32	read-create	Time Interval in milli seconds from the time a Vmux sends tone/s to a local PBX until it receives an acknowledgement from this PBX. Valid values: 60...400 in steps of 20.
INT ip2IfNextHopType	1.3.6.1.4.1.164.3.1.6.7.1.1.55	INTEGER	read-create	This MIB object defines the Bundle next Hop Address Type.
INT ip2IfNoiseLevelForVAD	1.3.6.1.4.1.164.3.1.6.7.1.1.56	INTEGER	read-create	This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to handle.
INT ip2IfClockPreferences	1.3.6.1.4.1.164.3.1.6.7.1.1.57	INTEGER	read-create	The Clock preferences: accurateness (2) = Accurate clock is more important than Constant Delay. constantDelay (3)= Constant Delay is more important than Accurate clock .
INT ip2IfConnectionMode	1.3.6.1.4.1.164.3.1.6.7.1.1.58	INTEGER	read-create	The Connection Mode: tdmOIpCe (2) = TDMOiP (CE) = Circuit Emulation. tdmOIpCv (3)= TDMOiP (CV) = Compressed Voice.
INT ip2IfRingBack	1.3.6.1.4.1.164.3.1.6.7.1.1.59	INTEGER	read-create	Enables or disable Ring Back.
INT ip2IfReversePolarity	1.3.6.1.4.1.164.3.1.6.7.1.1.60	INTEGER	read-create	Enables or disable Reverse polarity synthesis.
INT ip2IfPulseMeter	1.3.6.1.4.1.164.3.1.6.7.1.1.61	INTEGER	read-create	Enables or disable Pulse metering synthesis.
INT ip2IfPulseMeterFreq	1.3.6.1.4.1.164.3.1.6.7.1.1.62	INTEGER	read-create	Frequency of synthesized pulse metering for this bundle.
I32 ip2IfPulseMeterPeriod	1.3.6.1.4.1.164.3.1.6.7.1.1.63	Integer32	read-create	Duration of synthesized pulse metering. current values are: 100-250.
INT ip2IfOnHookDetect	1.3.6.1.4.1.164.3.1.6.7.1.1.64	INTEGER	read-create	Enables or disable immediate reaction to On-Hook bits from network in Ringing.
INT ip2IfComfortNoiseGen	1.3.6.1.4.1.164.3.1.6.7.1.1.65	INTEGER	read-create	Enable or disable Comfort Noise Generation (CNG). When this parameter is enabled and no voice payload exists on the line for some time period during the call (moments of silence), the device will generate a soft background noise which assures the user that the connection is still alive (CNG). When this parameter is disabled and no voice payload exists on the line, absolute silence will be heard (Comfort Noise will not be generated).
I32 ip2IfExitChannel	1.3.6.1.4.1.164.3.1.6.7.1.1.66	Integer32	read-create	The channelized bundle that the voice bundle exits through. In Gmux2000 it is the ifIndex of the Channelized Bundle (sub-channel) that the Voice Bundle exits through. The ifIndex contains the Slot+Prt+Channelized Bundle No.
I32 ip2IfMaxVBDModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.67	Integer32	read-create	Maximum VBD modem calls for this bundle.
I32 ip2IfMaxRelayModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.68	Integer32	read-create	Maximum Relay modem calls for this bundle.
INT ip2IfCustomToneFrequency	1.3.6.1.4.1.164.3.1.6.7.1.1.69	INTEGER	read-create	This is the frequency of the Custom Tone that is sent between PBXs in order to check that the line status is OK. When the Custom Tone Detection is enabled the device will not compress/decompress this tone. The custom tone that is received from the local PBX will be sent to the remote PBX with the same frequency it was received. When the Custom Tone Frequency is f1780Plus2000Hz (4), the device will not compress/decompress any tone with frequencies of 1780Hz or 2000 Hz.
INT ip2IfVadMethod	1.3.6.1.4.1.164.3.1.6.7.1.1.70	INTEGER	read-create	Voice Activity Detection (VAD) method. proprietary (2) - non standard VAD based only on power measurement. It is very sensitive to background noise. internalITUT (3) - standard ITU-T VAD. It is a robust method.
I32 ip2IfRxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.71	Integer32	read-create	Receive gain in dBm.
INT ip2IfCallerIDType	1.3.6.1.4.1.164.3.1.6.7.1.1.72	INTEGER	read-create	Caller ID Type used by the DSP for this bundle. Bellcore type is used by the American method. V.23 type is used by the European method.
INT ip2IfPeerAddrType	1.3.6.1.4.1.164.3.1.6.7.1.1.73	INTEGER	read-create	This MIB object defines the peer Address Type.
INT ip2IfVbdRate	1.3.6.1.4.1.164.3.1.6.7.1.1.74	INTEGER	read-create	Voice Band Data (VBD) rate for this bundle.
INT ip2IfDtmfDetection	1.3.6.1.4.1.164.3.1.6.7.1.1.75	INTEGER	read-create	Enable/Disable DTMF (Dual Tone Multi Frequency) detectors for this bundle.
U32 ip2IfNlpCutoffLevel	1.3.6.1.4.1.164.3.1.6.7.1.1.76	Unsigned32	read-create	Non Linear Processor (NLP) Cutoff Level for this bundle. This parameter is used by the echo canceller. It is the maximum absolute linear PCM amplitude of the near-end signal that will cause the NLP module to be active and to mute low level residual echo & noisy surroundings.
U32 ip2IfDtdErlRatioCutoffQ3	1.3.6.1.4.1.164.3.1.6.7.1.1.77	Unsigned32	read-create	The DTD ERL cutoff level is used in order to determine whether the near-end is talking or not. This parameter is used by the echo canceller when echo exists and there is voice with low volume on the line. DTD means Double Talk Detection. ERL means Echo Return Loss. It is the power difference [dB] between the far-end signal to the echo returned. The cutoff level is calculated for the value entering Q.3. This value will be divided by 2^3=8 in order to get the linear ratio.
INT ip2IfCASRedundancy	1.3.6.1.4.1.164.3.1.6.7.1.1.78	INTEGER	read-create	Enable/Disable CAS signaling redundancy. This parameter is useful when there are problems with the network and applicable only for CAS signaling: E1-MF (G.732S) or E1-CRC-MF (G.732SCRC ). enable (3) - means that each packet containing CAS signaling will be triplicated into 3 packets. disable (2)- No redundancy will exist. Only 1 packet containing CAS will be transmitted.
INT ip2IfBundleSensitivity	1.3.6.1.4.1.164.3.1.6.7.1.1.79	INTEGER	read-create	Denotes if the bundle is sensitive to delay in the network, or is sensitive to data errors in the network. Voice bundles are sensitive to delay; Non-voice bundles are sensitive to data errors.
INT ip2IfOAMBundleIdent	1.3.6.1.4.1.164.3.1.6.7.1.1.80	INTEGER	read-create	Denotes if an OAM bundle is identified according to the Bundle Number (0x3fff), or according to the value of the first nibble in the VCCV control word sent in the frame. controlWord - applicable only when ip2IfProtocolVersion = v2(2). When ip2IfProtocolVersion = v1(1), only bundleNumber is applicable.
U32 ip2IfMaxTxQueue	1.3.6.1.4.1.164.3.1.6.7.1.1.81	Unsigned32	read-create	Max Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on the network. High buffer size allows to store this burst and not lose packets.
U32 ip2IfMaxGprsTxQueue	1.3.6.1.4.1.164.3.1.6.7.1.1.82	Unsigned32	read-create	Max GPRS Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on the network. High buffer size allows to store this burst and not lose packets.
INT ip2IfV23HD	1.3.6.1.4.1.164.3.1.6.7.1.1.83	INTEGER	read-create	This parameter shows whether V.23 Half Duplex Modem Protocol is enabled on the bundle.
OCT ip2IfModemProtocolMode	1.3.6.1.4.1.164.3.1.6.7.1.1.84	OCTET STRING	read-create	This octet string contains the mode of each Modem Protocol used on the bundle. For each protocol one octet will be used. Octet #1 will be used for V.22 Protocol. Octet #2, #3, #4... are reserved for future protocols. Octet #1 values: 0 - Not Applicable 1 - VBD: Voice Band Data. 2 - Relay: Pulse Code Modulated (PCM) data is sent via the bundle. For V.22: This MIB object is relevant only when ip2IfModemCalls = relay (4).
U32 ip2IfCdisCngDetectionTime	1.3.6.1.4.1.164.3.1.6.7.1.1.85	Unsigned32	read-create	When working with CDIS (Call DIScrimination method) or CNG (Comfort Noise Generation): The time in msec that the device will detect 1100Hz & 2100Hz signals on the line before switching to modem or fax. For Vmux: the values will be in steps of 10 msec.
OCT ip2IfSuperTandemBitMask	1.3.6.1.4.1.164.3.1.6.7.1.1.86	OCTET STRING	read-create	This MIB object enables controlling the Time Slot/Channel rate. Valid values: 1 - FF HEX Each BIT represents 1/8 of the TS. Example: 7E (0111 1110) means that 6/8 of the TS (the center ones) are masked and data will be Tx/Rx only through them. This MIB object is relevant only when Super Tandem is enabled.
U32 ip2IfVbdSwitchbackTime	1.3.6.1.4.1.164.3.1.6.7.1.1.87	Unsigned32	read-create	Time in msec required for the DSP to switch back from VBD (Voice Band Data) to Voice. For Vmux: the values will be in steps of 30 msec.
I32 ip2IfCallerIdTxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.88	Integer32	read-create	The gain value in dBm units used for transmitting the Caller ID signal on the bundle.
I32 ip2IfCallerIdRxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.89	Integer32	read-create	The gain value in dBm units of the Caller ID signal received on the bundle.
INT ip2IfUdpMuxMethod	1.3.6.1.4.1.164.3.1.6.7.1.1.90	INTEGER	read-create	This parameter determines according to which field the multiplexing is made: srcPort (2) - multiplexing according to the UDP Source Port (Dest=0x085e). This should be the default value, for backwards compatibility. destPort (3) - multiplexing according to the UDP Destination Port (standard multiplexing). The UDP Source and Destination ports' range is determined according to ip2IfUdpMuxMethod value: For srcPort (2) the range is 1-7000 For destPort (3) the range is 49152-65535.
INT ip2IfCallerIdDetection	1.3.6.1.4.1.164.3.1.6.7.1.1.91	INTEGER	read-create	Enable/Disable Caller ID Detection for this bundle.
INT ip2IfWap	1.3.6.1.4.1.164.3.1.6.7.1.1.92	INTEGER	read-create	Enable/Disable WAP (Wireless Application Protocol) for this bundle. WAP allows users to access the internet from wireless devices.
I32 ip2IfTDMFrameBytes	1.3.6.1.4.1.164.3.1.6.7.2	Integer32	read-write	The number of TDM bytes to be placed in a single IP frame payload.
I32 ip2IfTosValue	1.3.6.1.4.1.164.3.1.6.7.3	Integer32	read-write	The TOS value to write in the IP frame.
INT ip2IfVlanTagging	1.3.6.1.4.1.164.3.1.6.7.4	INTEGER	read-write	VLAN support. no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
I32 ip2IfVlanID	1.3.6.1.4.1.164.3.1.6.7.5	Integer32	read-write	VLAN ID.
I32 ip2IfVlanPriority	1.3.6.1.4.1.164.3.1.6.7.6	Integer32	read-write	Frame priority.
ip2IfStatTable	1.3.6.1.4.1.164.3.1.6.7.7		not-accessible	Channels (Bundles) Statistics Table.
ip2IfStatEntry	1.3.6.1.4.1.164.3.1.6.7.7.1		not-accessible	IP Statistics per bundle
I32 ip2IfStatChIndex	1.3.6.1.4.1.164.3.1.6.7.7.1.1	Integer32	read-only	The channel index, which is actualy the bundle ID.
I32 ip2IfStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.7.1.2	Integer32	read-only	Number of events that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state.
I32 ip2IfStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.7.1.3	Integer32	read-only	Number of events that the buffer underflows. This records the count of the number of events the Receive (Eth to TDM) buffer underflows. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
I32 ip2IfStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.7.1.4	Integer32	read-only	Number of events that the buffer overflows. This records the count of the number of events the Receive (Eth to TDM) buffer overflows.
C32 ip2IfStatTxOnTimeInterval	1.3.6.1.4.1.164.3.1.6.7.7.1.5	Counter32	read-only	Number of frames that were transmitted due to time interval elapse. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing time interval elapses. The packetizing time interval is the interval in msec that it takes to build a Max. size frame.
C32 ip2IfStatTxOnMaxSize	1.3.6.1.4.1.164.3.1.6.7.7.1.6	Counter32	read-only	Number of frames that were transmitted due to reaching max. frame size. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing time interval elapses.
C32 ip2IfStatRxSignaling	1.3.6.1.4.1.164.3.1.6.7.7.1.7	Counter32	read-only	Number of signaling frames that were received.
C32 ip2IfStatRxVoice	1.3.6.1.4.1.164.3.1.6.7.7.1.8	Counter32	read-only	Number of voice frames that were received.
C32 ip2IfStatRxHdlc	1.3.6.1.4.1.164.3.1.6.7.7.1.9	Counter32	read-only	Number of HDLC frames that were received.
C32 ip2IfStatTxSignaling	1.3.6.1.4.1.164.3.1.6.7.7.1.10	Counter32	read-only	Number of signaling frames that were transmitted.
C32 ip2IfStatTxVoice	1.3.6.1.4.1.164.3.1.6.7.7.1.11	Counter32	read-only	Number of voice frames that were transmitted.
C32 ip2IfStatTxHdlc	1.3.6.1.4.1.164.3.1.6.7.7.1.12	Counter32	read-only	Number of HDLC frames that were transmitted.
C32 ip2IfStatRdnFlip	1.3.6.1.4.1.164.3.1.6.7.7.1.13	Counter32	read-only	Number of redundancy flips occured. This parameter counts only flips from this bundle to the other bundle in the redundancy couple.
I32 ip2IfFarEndTdmStatus	1.3.6.1.4.1.164.3.1.6.7.7.1.14	Integer32	read-only	This variable indicates the Status of the Far-End TDM Line. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The farEndTdmNoDefect must be set if and only if no other flag is set. The various bit positions are: 1 farEndTdmNoDefect 2 farEndTdmAIS Alarm Indication Signal 4 farEndTdmRDI Remote Defect Indication
C32 ip2IfStatPsnTxFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.15	Counter32	read-only	Number of frames that were transmitted to PSN.
C32 ip2IfStatPsnRxFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.16	Counter32	read-only	Number of frames that were recieved from PSN.
U32 ip2IfStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.7.1.17	Unsigned32	read-only	The Minimum jitter buffer level (in msec).
U32 ip2IfStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.7.1.18	Unsigned32	read-only	The Maximum jitter buffer level (in msec).
U32 ip2IfStatRecommendedJittBufSize	1.3.6.1.4.1.164.3.1.6.7.7.1.19	Unsigned32	read-only	The Recommended jitter buffer Size (in msec). 0= not applicable.
C32 ip2IfStatPsnSeqErrors	1.3.6.1.4.1.164.3.1.6.7.7.1.20	Counter32	read-only	Number of times that the sequence number of an incoming Frame indicates Loss of Frame or Out of order occured in PSN.
C32 ip2IfStatPsnReorderFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.21	Counter32	read-only	Number of times that Frames had been reordered in PSN.
U32 ip2IfStatMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.22	Unsigned32	read-only	The minimum Round Trip delay (in msec). 0= not applicable.
U32 ip2IfStatMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.23	Unsigned32	read-only	The maximum Round Trip delay (in msec). 0= not applicable.
U32 ip2IfStatAvrRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.24	Unsigned32	read-only	The avarage Round Trip delay (in msec). 0= not applicable.
C32 ip2IfStatFrameTrackDupDrop	1.3.6.1.4.1.164.3.1.6.7.7.1.25	Counter32	read-only	The number of packets dropped due to being duplicated. (duplicated packet means a packet that has the same sequential number as a packet being received previously).
C32 ip2IfStatFrameTrackMissing	1.3.6.1.4.1.164.3.1.6.7.7.1.26	Counter32	read-only	The number of packets that are missing. (Missing packet means an expected packet- according to the current sequential number - that was not received).
I32 ip2IfStatFrameTrackLongSerMiss	1.3.6.1.4.1.164.3.1.6.7.7.1.27	Integer32	read-only	The longest series of consecutive missing sequential numbers. Missing sequential numbers represent missing packets that was expected to be received successively.
I32 ip2IfStatTxMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.7.1.28	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
I32 ip2IfStatRxMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.7.1.29	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the received payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
C32 ip2IfStatHdlcCrcErr	1.3.6.1.4.1.164.3.1.6.7.7.1.30	Counter32	read-only	This counter indicates the number of received HDLC frames with CRC errors.
C32 ip2IfStatHdlcAlignErr	1.3.6.1.4.1.164.3.1.6.7.7.1.31	Counter32	read-only	This counter indicates the number of received HDLC frames with alignment errors.
C32 ip2IfStatHdlcOversize	1.3.6.1.4.1.164.3.1.6.7.7.1.32	Counter32	read-only	This counter indicates the number of received HDLC frames longer than 1470.
C32 ip2IfStatHdlcUndersize	1.3.6.1.4.1.164.3.1.6.7.7.1.33	Counter32	read-only	This counter indicates the number of received HDLC frames shorter than 4.
C32 ip2IfStatHdlcAbort	1.3.6.1.4.1.164.3.1.6.7.7.1.34	Counter32	read-only	This counter indicates the number of received HDLC frames with abort indication.
C32 ip2IfStatRxCorrectFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.35	Counter32	read-only	Number of received correct frames.
C32 ip2IfStatHdlcErroredFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.36	Counter32	read-only	Number of received errored HDLC frames.
I32 ip2IfRateLimit	1.3.6.1.4.1.164.3.1.6.7.8	Integer32	read-write	The maximum rate permitted to transfer via the network portin Mbps.
ip2IfPortTable	1.3.6.1.4.1.164.3.1.6.7.9		not-accessible	Port Table.
ip2IfPortEntry	1.3.6.1.4.1.164.3.1.6.7.9.1		not-accessible	Application layer configuration per Port
I32 ip2IfPortIndex	1.3.6.1.4.1.164.3.1.6.7.9.1.1	Integer32	read-only	The Port index, which is actualy the ifIndex.
I32 ip2IfPortUsage	1.3.6.1.4.1.164.3.1.6.7.9.1.2	Integer32	read-only	This parameter indicates the usage of the port (percents).
INT ip2IfPortMask	1.3.6.1.4.1.164.3.1.6.7.9.1.3	INTEGER	read-write	This parameter defines whether Agent will mask port's alarms and statistics or not.
I32 ip2IfPortTotalThroughput	1.3.6.1.4.1.164.3.1.6.7.9.1.4	Integer32	read-only	This parameter indicates the total Throughput of the port in bps.
ip2IfCurrentStatTable	1.3.6.1.4.1.164.3.1.6.7.10		not-accessible	Channels (Bundles) Current Statistics Table.
ip2IfCurrentStatEntry	1.3.6.1.4.1.164.3.1.6.7.10.1		not-accessible	IP Current Statistics per bundle
C32 ip2IfCurrentStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.10.1.1	Counter32	read-only	Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the current interval.
C32 ip2IfCurrentStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.10.1.2	Counter32	read-only	Number of seconds that the buffer underflows in the current interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflows in the current interval. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
C32 ip2IfCurrentStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.10.1.3	Counter32	read-only	Number of seconds that the buffer overflows in the current interval. This records the count of the number of seonds the Receive (Eth to TDM) buffer overflows in the current interval.
I32 ip2IfCurrentStatMaxDelayVar	1.3.6.1.4.1.164.3.1.6.7.10.1.4	Integer32	read-only	The maximum deviation from the center of the buffer (in msec) for the current interval.
U32 ip2IfCurrentStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.10.1.5	Unsigned32	read-only	The Minimum jitter buffer level (in msec) for the current interval.
U32 ip2IfCurrentStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.10.1.6	Unsigned32	read-only	The Maximum jitter buffer level (in msec) for the current interval.
C32 ip2IfCurrentStatTxErrFrameSec	1.3.6.1.4.1.164.3.1.6.7.10.1.7	Counter32	read-only	The number of seconds in which errored frames were transmitted during the current interval. The error may be one of the following: CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.
ip2IfIntervalStatTable	1.3.6.1.4.1.164.3.1.6.7.11		not-accessible	Channels (Bundles) Interval Statistics Table.
ip2IfIntervalStatEntry	1.3.6.1.4.1.164.3.1.6.7.11.1		not-accessible	IP Interval Statistics per bundle
I32 ip2IfIntervalStatIndex	1.3.6.1.4.1.164.3.1.6.7.11.1.1	Integer32	read-only	The Interval index, which is actualy the Interval number.
C32 ip2IfIntervalStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.11.1.2	Counter32	read-only	Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the selected interval.
C32 ip2IfIntervalStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.11.1.3	Counter32	read-only	Number of seconds that the buffer underflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflows in the selected interval. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
C32 ip2IfIntervalStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.11.1.4	Counter32	read-only	Number of seconds that the buffer overflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer overflows in the selected interval.
I32 ip2IfIntervalStatMaxDelayVar	1.3.6.1.4.1.164.3.1.6.7.11.1.5	Integer32	read-only	The maximum size of the buffer (in 10's of usec) in the selected interval.
U32 ip2IfIntervalStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.11.1.6	Unsigned32	read-only	The Minimum jitter buffer level (in msec) for the selected interval.
U32 ip2IfIntervalStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.11.1.7	Unsigned32	read-only	The Maximum jitter buffer level (in msec) for the selected interval.
C32 ip2IfIntervalStatTxErrFrameSec	1.3.6.1.4.1.164.3.1.6.7.11.1.8	Counter32	read-only	The number of seconds in which errored frames were transmitted during the selected interval. The error may be one of the following: CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.
INT ip2IfLogEvents	1.3.6.1.4.1.164.3.1.6.7.12	INTEGER	read-write	This parameter defines whether all Jitter Buffer and Sequence Number events will enter to Log File, or enter those events to Log file in one minute steps.
INT ip2IfEthSwitchMode	1.3.6.1.4.1.164.3.1.6.7.13	INTEGER	read-write	This parameter defines whether Eth Switch is in VLAN Tagged mode.
broadbandIf	1.3.6.1.4.1.164.3.1.6.8
bdbandConfig	1.3.6.1.4.1.164.3.1.6.8.1
prtBdbandIndTable	1.3.6.1.4.1.164.3.1.6.8.1.1		not-accessible	The Indication Signal table.
prtBdbandIndEntry	1.3.6.1.4.1.164.3.1.6.8.1.1.1		not-accessible	An entry in the Indication Signal table.
I32 prtBdbandCnfgIdx	1.3.6.1.4.1.164.3.1.6.8.1.1.1.1	Integer32	read-only	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
I32 prtBdbandIdx	1.3.6.1.4.1.164.3.1.6.8.1.1.1.2	Integer32	read-only	This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.
INT prtBdbandIndSig	1.3.6.1.4.1.164.3.1.6.8.1.1.1.3	INTEGER	read-only	This object indicates a unique Indication Signal. ais(1) = AIS = Alarm Indication Signal. rdi(2) = RDI = Remote Defect Indication.
INT prtBdbandIndEvent	1.3.6.1.4.1.164.3.1.6.8.1.1.1.4	INTEGER	read-only	This object indicates a unique Event that can cause the Indication Signal. slm(2) = SLM = Signal Label Mismatch eed(4) = EED = Excessive Error Defect pathTrace(5) = the end-to-end source/destination of information is wrong. lom(6) = LOM = Loss of Multiframe. lop(7) = LOP = Loss of Pointer. slu(8) = SLU = Signal Label Unequipped.
INT prtBdbandIndSigEnable	1.3.6.1.4.1.164.3.1.6.8.1.1.1.5	INTEGER	read-create	This object allows user to define if the event specified by prtBdbandIndEvent will cause creation of the Indication Signal specified by prtBdbandIndSig or not. disable - will not enable causing the signal enable - will enable causing the signal.
ROW prtBdbandRowStatus	1.3.6.1.4.1.164.3.1.6.8.1.1.1.6	RowStatus	read-create	Creation/Deletion of rows in the table.
prtPhyConfigTable	1.3.6.1.4.1.164.3.1.6.8.1.2		not-accessible	The Phy Config table. Used now for Phy25.6 Mbps.
prtPhyConfigEntry	1.3.6.1.4.1.164.3.1.6.8.1.2.1		not-accessible	An entry in the Phy Config table.
I32 prtPhyTimeElapsed	1.3.6.1.4.1.164.3.1.6.8.1.2.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period.
I32 prtPhyValidIntervals	1.3.6.1.4.1.164.3.1.6.8.1.2.1.2	Integer32	read-only	The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute since the interface has been online.
prtPhyPerfHistory	1.3.6.1.4.1.164.3.1.6.8.2
prtPhyCurrentTable	1.3.6.1.4.1.164.3.1.6.8.2.1		not-accessible	The 25.6 Mbps Section/Line Current table.
prtPhyCurrentEntry	1.3.6.1.4.1.164.3.1.6.8.2.1.1		not-accessible	An entry in the 25.6 Mbps Line Current table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.
G32 prtPhyCurrentLOS	1.3.6.1.4.1.164.3.1.6.8.2.1.1.1	Gauge32	read-only	The counter associated with the number of Loss Of Sync seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentLSV	1.3.6.1.4.1.164.3.1.6.8.2.1.1.2	Gauge32	read-only	The counter associated with the number of Line symbol violation seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentUAS	1.3.6.1.4.1.164.3.1.6.8.2.1.1.3	Gauge32	read-only	The counter associated with the number of UAS encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentSES	1.3.6.1.4.1.164.3.1.6.8.2.1.1.4	Gauge32	read-only	The counter associated with the number of SES encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentES	1.3.6.1.4.1.164.3.1.6.8.2.1.1.5	Gauge32	read-only	The number of Errored Seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
OCT prtPhyCurrentStatus	1.3.6.1.4.1.164.3.1.6.8.2.1.1.6	OCTET STRING	read-only	The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
G32 prtPhyCurrentLOF	1.3.6.1.4.1.164.3.1.6.8.2.1.1.7	Gauge32	read-only	The number of Loss of Frames, encountered by an interface in the current 15 minute interval.
prtPhyIntervalTable	1.3.6.1.4.1.164.3.1.6.8.2.2		not-accessible	The Line Interval table.
prtPhyIntervalEntry	1.3.6.1.4.1.164.3.1.6.8.2.2.1		not-accessible	An entry in the 25.6 Mbps Line Interval table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.
I32 prtPhyIntervalNumber	1.3.6.1.4.1.164.3.1.6.8.2.2.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 prtPhyIntervalLOS	1.3.6.1.4.1.164.3.1.6.8.2.2.1.2	Gauge32	read-only	The counter associated with the number of Loss Of Sync seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalLSV	1.3.6.1.4.1.164.3.1.6.8.2.2.1.3	Gauge32	read-only	The counter associated with the number of line symbol violation seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalUAS	1.3.6.1.4.1.164.3.1.6.8.2.2.1.4	Gauge32	read-only	The counter associated with the number of UAS encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalSES	1.3.6.1.4.1.164.3.1.6.8.2.2.1.5	Gauge32	read-only	The counter associated with the number of SES encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalES	1.3.6.1.4.1.164.3.1.6.8.2.2.1.6	Gauge32	read-only	The number of Errored Seconds, encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
OCT prtPhyIntervalStatus	1.3.6.1.4.1.164.3.1.6.8.2.2.1.7	OCTET STRING	read-only	The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
G32 prtPhyIntervalLOF	1.3.6.1.4.1.164.3.1.6.8.2.2.1.8	Gauge32	read-only	The number of Loss of Frames, encountered by an interface in one of the previous 96, individual 15 minute intervals.
muxHub	1.3.6.1.4.1.164.3.2
muxHubEvents	1.3.6.1.4.1.164.3.2.0			The events for .
NTF alarmsTrap	1.3.6.1.4.1.164.3.2.0.1			This trap is sent whenever alarm occurs in the agent.
NTF sanityTrap	1.3.6.1.4.1.164.3.2.0.2			This trap is sent after a data base update. It returns the sanity result status and the configuration no. checked. If the result is of Flip DB Sanity Check, the configuration no. sent will be 0. If the result is of Variant Sanity Check, the configuration no. sent will be 100.
NTF cnfgFlipTrap	1.3.6.1.4.1.164.3.2.0.3			This trap is sent upon change of the active Configuration DB. Attached, is the new active Configuration no.
NTF flipDbChangeTrap	1.3.6.1.4.1.164.3.2.0.4			This trap is sent upon change of the active Flip tables (Flip DB).
NTF statusChangedTrap	1.3.6.1.4.1.164.3.2.0.5			This trap is sent upon any change of the LEDs status.
agnMux	1.3.6.1.4.1.164.3.2.1
mdlMux	1.3.6.1.4.1.164.3.2.2
cnfgMdlMux	1.3.6.1.4.1.164.3.2.2.1
mdlPbxFramerCnfg	1.3.6.1.4.1.164.3.2.2.1.1
mdlPbxFramerCnfgTable	1.3.6.1.4.1.164.3.2.2.1.1.1		not-accessible	This table contains parameters relevant to a module belonging to a digital voice system, except mdlPbxFraEnhEcho which is relevant also for analog cards.
mdlPbxFramerCnfgEntry	1.3.6.1.4.1.164.3.2.2.1.1.1.1		not-accessible	An entry in table.
I32 mdlPbxFraCnfgIdx	1.3.6.1.4.1.164.3.2.2.1.1.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT mdlPbxFraSltIdx	1.3.6.1.4.1.164.3.2.2.1.1.1.1.2	INTEGER	read-only	The slot relevant to this module.
INT mdlPbxFraEnhEcho	1.3.6.1.4.1.164.3.2.2.1.1.1.1.3	INTEGER	read-write	Refers to external ports of an analogue module and to the internal ports of the other mvc4 types of modules. ms16(3) means that the four voice ports have enhanced echo of 16ms. ms32(4) means that the two first ports have enhanced echo of 32 ms while the last two ports have no enhanced echo.
INT mdlPbxFraTSGroupAss	1.3.6.1.4.1.164.3.2.2.1.1.1.1.4	INTEGER	read-write	In case of T1 modules: group1=(1,2,3,4), ...., group6=(21,22,23,24) while in case of E1 modules: - If prtExPh1MlLineType=g732sE1 or g732sE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,17), group5=(18,19,20,21),...,group7=(26,27,28,29) group8=(30,31). - If prtExPh1MlLineType=g732nE1 or g732nE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,16), group5=(17,18,19,20),...,group7=(25,26,27,28) group8=(29,30,31).
INT mdlPbxFraSignalMode	1.3.6.1.4.1.164.3.2.2.1.1.1.1.5	INTEGER	read-write	Refers to the signaling mode of the Framer module. tieTrunk(2), tieInvert(3), casTrans(4) are standard coding of the signaling protocol. casTrans(4) is Channel Associated Signaling (the signaling is within the channels time slot). ccsTrans(6) is Transparent Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). userDefined(5) allows the user to define the signaling protocol he wants. In this case, the next two MIB fields are relevant.
OCT mdlPbxFraSignalVector	1.3.6.1.4.1.164.3.2.2.1.1.1.1.6	OCTET STRING	read-write	In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote In conjunction with the Mask, mdlPbxFraSignalMask, it is possible to compute the signal mode.
OCT mdlPbxFraSignalMask	1.3.6.1.4.1.164.3.2.2.1.1.1.1.7	OCTET STRING	read-write	In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the 'don't care' A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote.
INT mdlPbxFraFramerSlot	1.3.6.1.4.1.164.3.2.2.1.1.1.1.8	INTEGER	read-write	Slot where is sitting the Framer.
INT mdlPbxFraSignaling	1.3.6.1.4.1.164.3.2.2.1.1.1.1.9	INTEGER	read-write	Signaling - describes the way the signaling ABCD bits pass from the local extension to the remote extension and vice-versa. endToEnd = the signaling ABCD bits pass without change from local to remote extension. localTermination = the signaling ABCD bits received from the local extension are translated to different ON Hook/OFF Hook bit values and then passed to remote extension. This is relevant when the Local and Remote ON Hook/OFF Hook values are different.
I32 mdlPbxFraTransSigTs	1.3.6.1.4.1.164.3.2.2.1.1.1.1.10	Integer32	read-write	This is the Time Slot that is used for Transparent CCS signaling. The values of this TS are 1-24 for T1 & 1-31 for E1. The default for E1 is 16 & for T1 it is 24. If no signaling is used then the TS should be 255 (None).
mdlProtIpTable	1.3.6.1.4.1.164.3.2.2.1.2		not-accessible	This table contains Protected IP Addresses for ML-IP cards when working in IP Ring Mode.
mdlProtIpEntry	1.3.6.1.4.1.164.3.2.2.1.2.1		not-accessible	An entry in table.
I32 mdlProtIpCnfgIdx	1.3.6.1.4.1.164.3.2.2.1.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being accessed. Idx 255 relates to the TmpCnfg. For Agents having several configuration, Write operation is allowed only to the Temporary Configuration.
INT mdlProtIpSlotIdx	1.3.6.1.4.1.164.3.2.2.1.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the 2104 Unit the entries io6(10)..io16) are not valid.
IP mdlProtIpAddress	1.3.6.1.4.1.164.3.2.2.1.2.1.3	IpAddress	read-only	A Protected IP address.
ROW mdlProtIpRowStatus	1.3.6.1.4.1.164.3.2.2.1.2.1.4	RowStatus	read-create	This parameter allows creating/deleting entries of this table.
statMdlMux	1.3.6.1.4.1.164.3.2.2.2
mdlStatTable	1.3.6.1.4.1.164.3.2.2.2.1		not-accessible	A table.
mdlStatEntry	1.3.6.1.4.1.164.3.2.2.2.1.1		not-accessible	An entry in table.
INT mdlStatSltIdx	1.3.6.1.4.1.164.3.2.2.2.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the mux. In the 2104 Unit the entries psB(2),clB(4),io6(10)..io12(16) are not valid.
IP mdlStatHostIP	1.3.6.1.4.1.164.3.2.2.2.1.1.2	IpAddress	read-only	The host interface IP address when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
IP mdlStatHostMask	1.3.6.1.4.1.164.3.2.2.2.1.1.3	IpAddress	read-only	The host interface subnet mask when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
IP mdlStatDefaultGateway	1.3.6.1.4.1.164.3.2.2.2.1.1.4	IpAddress	read-only	Default Gateway's IP Address when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
prtMux	1.3.6.1.4.1.164.3.2.3
statPrtMux	1.3.6.1.4.1.164.3.2.3.1
prtSExHsfStatTable	1.3.6.1.4.1.164.3.2.3.1.6		not-accessible	A table.
prtSExHsfStatEntry	1.3.6.1.4.1.164.3.2.3.1.6.1		not-accessible	An entry in table.
INT prtSExHsfSltIdx	1.3.6.1.4.1.164.3.2.3.1.6.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtSExHsfPrtIdx	1.3.6.1.4.1.164.3.2.3.1.6.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtSExHsfInterfaceTyp	1.3.6.1.4.1.164.3.2.3.1.6.1.3	INTEGER	read-only	This attribute indicates a unique interface type of a selected port.
INT prtSExHsfRts	1.3.6.1.4.1.164.3.2.3.1.6.1.4	INTEGER	read-only	This attribute indicates a unique RTS control signal state.
prtIsdnStatusTable	1.3.6.1.4.1.164.3.2.3.1.16		not-accessible	This table contains ISDN Statistics parameters that do not appear in the standard MIBs or for agents that don't support the standard Index of Call Set Up Time.
prtIsdnStatusEntry	1.3.6.1.4.1.164.3.2.3.1.16.1		not-accessible	Entries for ISDN Statistics parameters that do not appear in the standard MIBs or for agents that don't support the standard Index of Call Set Up Time.
INT prtIsdnStatusDspMode	1.3.6.1.4.1.164.3.2.3.1.16.1.1	INTEGER	read-only	The DSP can be in one of the following Modes: Voice, Idle, Fax, Voice Band Data (VBD)- Modem.
INT prtIsdnStatusCallState	1.3.6.1.4.1.164.3.2.3.1.16.1.2	INTEGER	read-only	The state that the current call is in.
STR prtIsdnStatusCallingNumber	1.3.6.1.4.1.164.3.2.3.1.16.1.3	DisplayString	read-only	This is the local Number (ISDN Address) associated with this entry.
STR prtIsdnStatusCalledNumber	1.3.6.1.4.1.164.3.2.3.1.16.1.4	DisplayString	read-only	This is the remote Number (ISDN Address) associated with this entry.
IP prtIsdnStatusCalledIP	1.3.6.1.4.1.164.3.2.3.1.16.1.5	IpAddress	read-only	This is the remote IP Address associated with this entry.
INT prtIsdnStatusCallDirection	1.3.6.1.4.1.164.3.2.3.1.16.1.6	INTEGER	read-only	Attribute indicating the Direction of the Call. The value of notApplicable will be used for example when prtIsdnStatusCallState = notActive(14).
cnfgPrtMux	1.3.6.1.4.1.164.3.2.3.2
prtClCnfg	1.3.6.1.4.1.164.3.2.3.2.1
prtExClCnfgTable	1.3.6.1.4.1.164.3.2.3.2.1.1		not-accessible	A table.
prtExClCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.1.1.1		not-accessible	All the entries at this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only to the TmpCnfg entry.
I32 prtExClCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExClSltIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. Because the second Cl is only for redundancy, all the parameters are identical in the two modules, i.e. change of any parameter in one module will change automatically the value of the other module.. In the ?004 Unit the entry clB(4) is not valid.
INT prtExClPrtIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtExClUsage	1.3.6.1.4.1.164.3.2.3.2.1.1.1.4	INTEGER	read-only	This attribute indicates what is the usage of the port.
INT prtExClRate	1.3.6.1.4.1.164.3.2.3.2.1.1.1.5	INTEGER	read-only	This attribute indicates the operation rate of the port.
INT prtExClDataBits	1.3.6.1.4.1.164.3.2.3.2.1.1.1.6	INTEGER	read-only	This attribute indicates the number of data bits in async frame
INT prtExClParity	1.3.6.1.4.1.164.3.2.3.2.1.1.1.7	INTEGER	read-only	This attribute indicates if the parity operation mode in async frame
INT prtExClStopBits	1.3.6.1.4.1.164.3.2.3.2.1.1.1.8	INTEGER	read-only	This attribute indicates the minimum number of stop bits in the tx async frame
INT prtExClRoutingProtocol	1.3.6.1.4.1.164.3.2.3.2.1.1.1.9	INTEGER	read-only	This attribute indicates the routing protocol of the port. When prtExClUsage is nmsSlip or nmsPpp - all values are applicable . Else - only 'none' is applicable.
INT prtExClEnabled	1.3.6.1.4.1.164.3.2.3.2.1.1.1.10	INTEGER	read-only	This attribute indicates if Ethernet port of CL is enabled or not for management. It is applicable only on the ETH port of the CL, when the MP includes an ML-IP card. disabled - will happen when there is Inband Management via the ML-IP link/s enabled - will happen when ML-IP link/s is not used for Inband Management, but CL's ETH port .
prtPh1MlCnfg	1.3.6.1.4.1.164.3.2.3.2.2
prtExPh1MlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.1		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to prtExPh1MlCnfgIdx=1.
prtExPh1MlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.1.1		not-accessible	An entry in table.
I32 prtExPh1MlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExPh1MlSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used.
INT prtExPh1MlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.3	INTEGER	read-only	This attribute indicates a unique port number. MP-2100/2200: MTML-1/E1 and MTML-1/T1 cards have only one external interface. inPrt1, inPrt2 - for MTML-H/2E1 and HSH cards. inPrt1..inPrt4 - for MTML-E2 and MSL-4 cards. exPrt2..exPrt4 - for MTML-4 cards and others exPrt1..exPrt8 - for ML-8 cards. inPrt1..inPrt8 - for MSL-8 and VF-30 card family. MP-104/204: only exPrt3 (3) is applicable. MP-4100: intPrt1...intPrt84 - for CLX cards. For other products' index see their specification.
INT prtExPh1MlConnect	1.3.6.1.4.1.164.3.2.3.2.2.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the card considerations because it may indicate that the module has only one physical interface.
INT prtExPh1MlLineType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.5	INTEGER	read-write	This attribute is the line type parameter for T1/E1 interface. The user should select only the values which are relevant to the specific port: (2),(3), (8) - for T1 port (4)..(7), (9) - for E1 port. (101) framed - This value does not exist in standard MIB and is used for a non-standard E1 port that doesn't has real framer. Note: for old devices, g732unframed(8) was used as E1 Unframed. That was because at the time this value did not exist in the standard MIB (RFC-1406), so we added it in private MIB. Now that it was added to standard MIB, private MIB was updated as well. This parameter has the same values as dsx1LineType in DS1 MIB (RFC-3895). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7) g732unframed dsx1Unframed (8) --from RFC-3895 e1Unframed dsx1E1Unframed (9) --from RFC-3895
INT prtExPh1MlLineCode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.6	INTEGER	read-write	This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for MPH.1/T1 E1 line code parameters for MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExPh1MlLineLen	1.3.6.1.4.1.164.3.2.3.2.2.1.1.7	INTEGER	read-write	This attribute is the line length parameter used only for T1/DSU interfaces. lenXXXpXXXft = len-XXX-XXXft.
INT prtExPh1MlRestoreTime	1.3.6.1.4.1.164.3.2.3.2.2.1.1.8	INTEGER	read-write	The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface.
INT prtExPh1MlTxGain	1.3.6.1.4.1.164.3.2.3.2.2.1.1.9	INTEGER	read-write	This attribute is the tx gain parameter used only for T1/CSU interfaces.
INT prtExPh1MlRxSensitivity	1.3.6.1.4.1.164.3.2.3.2.2.1.1.10	INTEGER	read-write	This attribute is the rx line sensitivity parameter. low26dBm, high36dBm - applicable for T1-CSU shortHaul, longHaul - applicable for MTML-4 cards low15dbm was added for vmux110/210 T1 ports.
I32 prtExPh1MlIdleCode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.11	Integer32	read-write	Determines the code for transmission in empty time slots. Type value(00-FFH), Excluding 0H,8H,10H,12H,21H,24H,42H,49H, 84H,92H
INT prtExPh1MlTdmTrunk	1.3.6.1.4.1.164.3.2.3.2.2.1.1.12	INTEGER	read-write	This attribute indicates whether the port is used to transfer TDM cards data and through which Bus.
INT prtExPh1MlClkMode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.13	INTEGER	read-write	Defines the clock operation mode of the T1/E1 interface. Ports that are connected to the TDM Buses must be in nodalTiming(3) clock mode.
INT prtExPh1MlMfClkSrcSlt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.14	INTEGER	read-write	This attribute indicates whether the port Tx multiframe is synchronized with Rx multiframe of another port and the slot position of that port. This operation is required in order to bypass signaling of PCM voice channels. Its value is always local(2) when the port isn't connected to any TDM bus. When it's value is local(2) there is no meaning to 'prtExPh1MlMfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPh1MlMfClkSrcPrt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.15	INTEGER	read-write	A unique number to identify a port position in the mux. It has no effect when the prtExPh1MlMfClkSrcSlt selected is Local. inPrt1 - for MTML-H/E1 cards.
INT prtExPh1MlFdlType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.16	INTEGER	read-write	A unique number to identify the side of the FDL operation. Normal: 'response' for the user side and 'command' for the PTT side. Applicable only when working with ESF-T1 link
INT prtExPh1MlInbandMng	1.3.6.1.4.1.164.3.2.3.2.2.1.1.17	INTEGER	read-write	A unique number to identify an Inband management over the link.
INT prtExPh1MlInbandMngRate	1.3.6.1.4.1.164.3.2.3.2.2.1.1.18	INTEGER	read-write	A unique number to identify the rate of the Inband management (Kbps). E1 port - it is not applicable when prtExPh1MlInbandMng selected is off. T1 port - it is not applicable when prtExPh1MlInbandMng selected is off OR fdlOrTs0.
INT prtExPh1MlRedundType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.19	INTEGER	read-write	This object determines the ML redundancy type: none - no ML redundacy dualCableAIS - each ML card is connected by a separate dualCableParallelTx cable to the other MUX (two cables connect two MUXes). There are two types of dual redundancy. yCable - Y cable is connected to both ML cards (one cable connects two MUXes). Default=none When only one ML card exists, the type can be only 'none'. The value should be the same for both ML slots.
INT prtExPh1MlRedundSlot	1.3.6.1.4.1.164.3.2.3.2.2.1.1.20	INTEGER	read-write	This object indicates the slot containing the redundacy ML card, coupled with the current ML (prtExPh1MlSltIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. In the ?004 Unit the entries io6(10)..io12(16) are not valid When value is not 'none', it should be mutual to the redundant ML slot.
INT prtExPh1MlRedundPort	1.3.6.1.4.1.164.3.2.3.2.2.1.1.21	INTEGER	read-write	This object indicates the redundacy ML port, coupled with the current ML port (prtExPh1MlPrtIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. When value is not 'none', it should be mutual to the redundant ML port. inPrt1 - for MTML-H/E1 cards. inPrt1..inPrt4 - for MTML-E2 cards. exPrt2..exPrt4 - for MTML-4 cards.
I32 prtExPh1MlRedundRecTime	1.3.6.1.4.1.164.3.2.3.2.2.1.1.22	Integer32	read-write	Redundancy Recovery Time (sec). After switching the ML card to the current (prtExPh1MlSltIdx), the next ML switch can be performed only after a minimum time, indicated by this object.
INT prtExPh1MlInbandMngRoutProt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.23	INTEGER	read-write	This attribute indicates the Inband Mng routing protocol of the port.
INT prtExPh1MlIfType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.24	INTEGER	read-write	Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values.
INT prtExPh1MlMultiplier	1.3.6.1.4.1.164.3.2.3.2.2.1.1.25	INTEGER	read-write	The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps.
I32 prtExPh1MlSupportedTS	1.3.6.1.4.1.164.3.2.3.2.2.1.1.26	Integer32	read-only	Number of Supported Time Slots by the agent. For Vmux-110 there is HW that supports less than 31/24 Time Slots for the E1/T1 port.
INT prtExPh1MlImpedance	1.3.6.1.4.1.164.3.2.3.2.2.1.1.27	INTEGER	read-write	The Line Impedance. For T1 (always balanced), impedance is 100 ohm. For E1: - balanced = 120 ohm - unbalanced = 75 ohm.
INT prtExPh1MlQ50BwControl	1.3.6.1.4.1.164.3.2.3.2.2.1.1.28	INTEGER	read-write	This object enables configuration of Q.50 Bandwidth Control on the port. If the bandwidth exceeds a certain threshold it is possible to disable new calls in the PBX via Q.50 protocol. Q.50 supports only E1 ports with Line Types: E1-MF (G.732S), E1-CRC-MF(G.732SCRC ) It does not support T1 ports. Annex A - the basic type of Q.50 which focuses only on the bandwidth control. Can use one of the following pairs of signaling bits: A&B or C&D. Annex B - Expansion of Annex A which includes also call release messages and Maintenance Messages. Uses A&B bits only.
INT prtExPh1MlQ50SignalPair	1.3.6.1.4.1.164.3.2.3.2.2.1.1.29	INTEGER	read-write	Q.50 Signaling bits Pair that is currently in use: A&B bits or C&D bits. For Annex B it will always be: aAndB (2).
INT prtExPh1MlInternalSwitch	1.3.6.1.4.1.164.3.2.3.2.2.1.1.30	INTEGER	read-write	This parameter shows whether the data will be transferred from one port to the other port within the same group of 2 ports. The default value is: Enable. Disable value might be necessary for security implementations or for ring applications. For Vmux-2100 device this parameter is used on the Channelized Cards. Both ports in each group should have the same value for this parameter.
INT prtExPh1MlSigService	1.3.6.1.4.1.164.3.2.3.2.2.1.1.31	INTEGER	read-write	Signaling Service given by this link. notApplicable - for T1 links normal - usual Signaling advanced - V5 Signaling.
I32 prtExPh1MlFragmentSize	1.3.6.1.4.1.164.3.2.3.2.2.1.1.32	Integer32	read-write	This parameter indicates the maximum number of bytes permitted in a packet send over the Link. Exceeding this size will cause packet fragmentation.
prtExPh1MlTsTable	1.3.6.1.4.1.164.3.2.3.2.2.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExPh1MlTsTest that will be written directly to the Active Configuration.
prtExPh1MlTsEntry	1.3.6.1.4.1.164.3.2.3.2.2.2.1		not-accessible	An entry in table.
I32 prtExPh1MlTsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExPh1MlTsSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (255) is used.
INT prtExPh1MlTsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.3	INTEGER	read-only	This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have only one external interface. exPrt2 - for ME1-2, MT1-2 and mhsPri cards. exPrt3, exPrt4 - for mhsPri cards. inPrt1 - for MTML-H/E1 cards.
I32 prtExPh1MlTsIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
INT prtExPh1MlTsIConSlot	1.3.6.1.4.1.164.3.2.3.2.2.2.1.5	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS).
I32 prtExPh1MlTsIConPrt	1.3.6.1.4.1.164.3.2.3.2.2.2.1.6	Integer32	read-write	This attribute indicates the internally (In Mux) connected/routed port. For MP, the values will be: { exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , noConnect (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109) , inPrt10 (110) , inPrt11 (111) , inPrt12 (112) } For other products see specific values at spec.
I32 prtExPh1MlTsIConTs	1.3.6.1.4.1.164.3.2.3.2.2.2.1.7	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated to multiframe synchronization and voice signaling.
OID prtExPh1MlTsExt	1.3.6.1.4.1.164.3.2.3.2.2.2.1.8	OBJECT IDENTIFIER	read-only	A pointer to an extension of this table: prtExTsSplitTable. - If prtExPh1MlTsIConSlot='split', its value should be set to the OBJECT IDENTIFIER of the prtExTsSplitTable, with its relevant CnfgIdx, SltIdx, PrtIdx, TsIdx and 1st TsBit. - If prtExPh1MlTsIConSlot is not 'split', its value should be set to the OBJECT IDENTIFIER { 0 0 }.
INT prtExPh1MlTsTest	1.3.6.1.4.1.164.3.2.3.2.2.2.1.9	INTEGER	read-write	This attribute indicates a test to be activated on the selected TS. It is applicable only when prtSTstCmd=testPerTS(31). notApplicable - when prtSTstCmd is NOT testPerTS(31). none - no test is applied for the selected TS. split - when the tests are per Bit of the selected TS.
INT prtExPh1MlTsType	1.3.6.1.4.1.164.3.2.3.2.2.2.1.10	INTEGER	read-write	The Time Slot Type. Transparent - means that the Time Slot will be Rx/Tx as is without processing it. If the device requires more than 1 unique data or ss7 Time Slot, options with numbers can be used like: data...data4. Each numbered Type can go to a different destination. ss7n2 - means the 2nd group of ss7 Time Slots. data2,data3, data4 mean group 2,3,4 of Data Time Slots. subCh1...subCh8 mean Sub Channel 1...8, respectively. trau, qmux, dynamic, signaling - are used by GSM devices.
I32 prtExPh1MlTsBundle	1.3.6.1.4.1.164.3.2.3.2.2.2.1.11	Integer32	read-write	The number of the bundle containing this Time Slot. If no bundle exists for this TS or the bundle number is irrelevant, the value will be 0.
I32 prtExPh1MlTsTestDuration	1.3.6.1.4.1.164.3.2.3.2.2.2.1.12	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific TS. This entry applies to all the test operations. For the Vmux2100 the values are: 0 - 60 seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtExPh1MlTsTest' parameter.
INT prtExPh1MlTsSubChType	1.3.6.1.4.1.164.3.2.3.2.2.2.1.13	INTEGER	read-write	The Time Slot Sub-Channel Type. This variable is relevant only when Time-Slot Type is SubCh (e.g. prtExPh1MlTsType = subCh1...subCh8).
I32 prtExPh1MlTsSubChMask	1.3.6.1.4.1.164.3.2.3.2.2.2.1.14	Integer32	read-write	The Sub-Channel Type Mask. This variable is relevant only when Time-Slot Type is SubCh (e.g. prtExPh1MlTsType = subCh1...subCh8).
INT prtExPh1MlTsChRate	1.3.6.1.4.1.164.3.2.3.2.2.2.1.15	INTEGER	read-write	The Rate of the Signaling Channel. notApplicable(1) when TS Type is other than Signaling or Transparent
INT prtExPh1MlTsByteReversal	1.3.6.1.4.1.164.3.2.3.2.2.2.1.16	INTEGER	read-write	Byte Reversal. This variable defines whether the LSB or MSB is transmitted first. no(2) - MSB is transmitted first yes(3) - LSB is transmitted first.
INT prtExPh1MlTsSigProfile	1.3.6.1.4.1.164.3.2.3.2.2.2.1.17	INTEGER	read-write	This object indicates the Signaling Profile of the port. It is applicable only when prtMl4SigProfile=perTS. p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5
prtInPh1MlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInPh1MlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.3.1		not-accessible	An entry in table.
I32 prtInPh1MlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtInPh1MlSltType	1.3.6.1.4.1.164.3.2.3.2.2.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For ISDN BRI port of MX300/30: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io12(16) are not valid
I32 prtInPh1MlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.3.1.3	Integer32	read-only	This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have three internal interfaces. MX3000 modules may have up to 50 internal ports.
INT prtInPh1MlConnect	1.3.6.1.4.1.164.3.2.3.2.2.3.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInPh1MlRate	1.3.6.1.4.1.164.3.2.3.2.2.3.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInPh1MlProtocol	1.3.6.1.4.1.164.3.2.3.2.2.3.1.6	INTEGER	read-write	This attribute indicates the applied protocol.
INT prtInPh1MlConnectionTyp	1.3.6.1.4.1.164.3.2.3.2.2.3.1.7	INTEGER	read-write	This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management operation (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetNotMana - indicates network internal line, but the remote mux is not managed by the nms. User - User to Network Interface. OtherNet - Network To Network Interfce. PubNet - Access Mux To PubNet Interface.
INT prtInPh1MlCongResponse	1.3.6.1.4.1.164.3.2.3.2.2.3.1.8	INTEGER	read-write	This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/receive becn to/from the network). no - do nothing FlowControl - translate the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done in both directions.
I32 prtInPh1MlCongLevel	1.3.6.1.4.1.164.3.2.3.2.2.3.1.9	Integer32	read-write	This attribute indicates the level of delayed data in precents of the total available dynamic memory, for which the port will start to operate . The resolution of the parameter is 5 percent. Valid values: 10..70, 255. 255=notApplicable.
INT prtInPh1MlTc	1.3.6.1.4.1.164.3.2.3.2.2.3.1.10	INTEGER	read-write	This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports in the specific card. 255=notApplicable.
INT prtInPh1MlFlowControl	1.3.6.1.4.1.164.3.2.3.2.2.3.1.11	INTEGER	read-write	This attribute indicates the required flow control betweeen the port and the remote equipment.
INT prtInPh1MlSegment	1.3.6.1.4.1.164.3.2.3.2.2.3.1.12	INTEGER	read-write	This object is the Segmentation in Bytes. In protocol FR+, ISDN internals, MX 30/300 the segmentation is: 50 (2) ,158 (3) ,266 (4) ,376 (5), 484 (6) In MX 3000/4: For protocol FR+ (internal ISDN ports of MHS.S, MHS.U, MHS.E1, MHS.T1 cards) segmentation values are: 236 (7),472 (8), 708 (9), 944 (10) ,1180 (11)
INT prtInPh1MlFrMngProt	1.3.6.1.4.1.164.3.2.3.2.2.3.1.13	INTEGER	read-write	This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtInPh1MlConnectionTyp = sameNetManaged, this object will be RO (internally determined).
I32 prtInPh1MlEnqPeriod	1.3.6.1.4.1.164.3.2.3.2.2.3.1.14	Integer32	read-write	This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlFullRptPeriod	1.3.6.1.4.1.164.3.2.3.2.2.3.1.15	Integer32	read-write	This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite (never sent). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlFrWindowSize	1.3.6.1.4.1.164.3.2.3.2.2.3.1.16	Integer32	read-write	This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlErrorsThreshold	1.3.6.1.4.1.164.3.2.3.2.2.3.1.17	Integer32	read-write	This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.2.3.1.18	Integer32	read-write	Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=Never. Never move to higher prioritized connected link. UNIT is seconds. Valid values are: 0, 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 120, 180, 240, 300, 360, 420, 480, 540, 600, 900, 1200, 1500, 1800. Attempt to Set an invalid value will result in getting the default value.
INT prtInPh1MlBearerCh	1.3.6.1.4.1.164.3.2.3.2.2.3.1.19	INTEGER	read-write	Defines which B (bearer) channels are used for transferring ISDN data. Default value is: none (255). anyChannel (2) is skipped because it is not in use here.
INT prtInPh1MlAssociatedExCh	1.3.6.1.4.1.164.3.2.3.2.2.3.1.20	INTEGER	read-write	This object indicates the external port associated to this internal port. At present, it is used by the Hybrid (mp2100h), MHS-4 cards which can have up to 64 dynamic internal ports associated with External ports. For ISDN cards, the value will be: notApplicable (255). The associated external of an ISDN internal port is represented by the MIB object: prtIsdnDirectoryPrtNu.
INT prtInPh1MlClockEncoding	1.3.6.1.4.1.164.3.2.3.2.2.3.1.21	INTEGER	read-write	This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols.
I32 prtInPh1MlMinSeparators	1.3.6.1.4.1.164.3.2.3.2.2.3.1.22	Integer32	read-write	Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable
INT prtInPh1MlCcittCrc	1.3.6.1.4.1.164.3.2.3.2.2.3.1.23	INTEGER	read-write	This object indicates how many Bits are used for CRC (HDLC item).
INT prtInPh1MlFrameSeparator	1.3.6.1.4.1.164.3.2.3.2.2.3.1.24	INTEGER	read-write	This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line.
prtInPh1MlDlciTable	1.3.6.1.4.1.164.3.2.3.2.2.4		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInPh1MlDlciEntry	1.3.6.1.4.1.164.3.2.3.2.2.4.1		not-accessible	An entry in table.
I32 prtInPh1MlDlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtInPh1MlDlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtInPh1MlDlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. MPH.1/E1 and MPH.1/T1 cards have three internal ports.
I32 prtInPh1MlDlciIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, then its type is 'user' and the only valid index is 1.
INT prtInPh1MlDlciValid	1.3.6.1.4.1.164.3.2.3.2.2.4.1.5	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
INT prtInPh1MlDlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.2.4.1.6	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtInPh1MlDlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.2.4.1.7	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to.
I32 prtInPh1MlDlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.2.4.1.8	Integer32	read-write	This attribute indicates a unique internal connection dlci number which the src dlci is routed to.
INT prtInPh1MlDlciTxBc	1.3.6.1.4.1.164.3.2.3.2.2.4.1.9	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line.
INT prtInPh1MlDlciTxBe	1.3.6.1.4.1.164.3.2.3.2.2.4.1.10	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line.
INT prtInPh1MlDlciRxBc	1.3.6.1.4.1.164.3.2.3.2.2.4.1.11	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line.
INT prtInPh1MlDlciRxBe	1.3.6.1.4.1.164.3.2.3.2.2.4.1.12	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line.
I32 prtInPh1MlDlciPriority	1.3.6.1.4.1.164.3.2.3.2.2.4.1.13	Integer32	read-write	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority.
INT prtInPh1MlDlciStatus	1.3.6.1.4.1.164.3.2.3.2.2.4.1.14	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
prtPhMlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.5		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtPhMlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.5.1		not-accessible	An entry in table.
I32 prtPhMlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtPhMlSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used.
INT prtPhMlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.3	INTEGER	read-only	This attribute indicates a unique port number. ML-20 cards have just one external interface.
INT prtPhMlConnect	1.3.6.1.4.1.164.3.2.3.2.2.5.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtPhMlRate	1.3.6.1.4.1.164.3.2.3.2.2.5.1.5	INTEGER	read-write	This attribute indicates the configured port speed. auto - rate is adapted automatically to the attached modem rate.
INT prtPhMlCAS	1.3.6.1.4.1.164.3.2.3.2.2.5.1.6	INTEGER	read-write	This attribute indicates whether Channel Associated Signaling (CAS) is used.
INT prtPhMlClockMode	1.3.6.1.4.1.164.3.2.3.2.2.5.1.7	INTEGER	read-write	Clock mode.
INT prtPhMlSatBuffer	1.3.6.1.4.1.164.3.2.3.2.2.5.1.8	INTEGER	read-write	Satellite Buffer (+/- 256).
INT prtPhMlDialProcess	1.3.6.1.4.1.164.3.2.3.2.2.5.1.9	INTEGER	read-write	Dial Process.
I32 prtPhMlSyncRestore	1.3.6.1.4.1.164.3.2.3.2.2.5.1.10	Integer32	read-write	Sync Restoration time, in seconds. notApplicable=0.
INT prtPhMlBus	1.3.6.1.4.1.164.3.2.3.2.2.5.1.11	INTEGER	read-write	The TDM BUS this port is linked to.
INT prtPhMlMfSyncSlot	1.3.6.1.4.1.164.3.2.3.2.2.5.1.12	INTEGER	read-write	This attribute indicates whether the sync is synchronized according to a certain card and the slot of this card. This operation is required in order to bypass signaling of PCM voice channels. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtPhMlClockSource	1.3.6.1.4.1.164.3.2.3.2.2.5.1.13	INTEGER	read-write	The Clock Source: TC (Tx Clock) or RC (Rx Clock) signals.
INT prtPhMlErrCorrection	1.3.6.1.4.1.164.3.2.3.2.2.5.1.14	INTEGER	read-write	This object indicates if Error Correction mechanism should be applied or not. It will be applicable only if the interface HW includes the Error Correction chip.
INT prtPhMlCorrectionMode	1.3.6.1.4.1.164.3.2.3.2.2.5.1.15	INTEGER	read-write	This object is applicable only when prtPhMlErrCorrection=yes. random - enables to correct up to 3 random errors in an 23 bit frame built from 12 data bits and 11 appended parity bits. bursty - interleaving 3 frames, allows correcting bursts of 9 bit length.
INT prtPhMlControlSignals	1.3.6.1.4.1.164.3.2.3.2.2.5.1.16	INTEGER	read-write	This object shows whether the Port will ignore or implement the control signals like DCD, CTS, DTR.
INT prtPhMlInterfaceType	1.3.6.1.4.1.164.3.2.3.2.2.5.1.17	INTEGER	read-write	The SW Configurable Interface Type.
INT prtPhMlClockPolarity	1.3.6.1.4.1.164.3.2.3.2.2.5.1.18	INTEGER	read-write	This object indicates the clock polarity.
prtPhPlCnfg	1.3.6.1.4.1.164.3.2.3.2.3
prtExPhPlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.3.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExPhPlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.3.1.1		not-accessible	An entry in table.
I32 prtExPhPlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExPhPlSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtExPhPlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.3	INTEGER	read-only	This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid.
INT prtExPhPlConnect	1.3.6.1.4.1.164.3.2.3.2.3.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExPhPlHRate	1.3.6.1.4.1.164.3.2.3.2.3.1.1.5	INTEGER	read-write	This attribute indicates the port speed for HIGH speed cards. The card has limitations about the maximum sigma channel speeds and about the possible rates for each clock mode . N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. 'r9d6KbpsNLE' means rate of 9.6 Kbps ('d'=dot). Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r2048KbpsE (63), -- r2048KbpsNLE
INT prtExPhPlLRate	1.3.6.1.4.1.164.3.2.3.2.3.1.1.6	INTEGER	read-write	This attribute indicates the port speed for LOW speed cards. The card has limitations about the possible rates for each clock mode. N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r57600bpsLE (16), -- r57600bpsNLE
INT prtExPhPlProtocol	1.3.6.1.4.1.164.3.2.3.2.3.1.1.7	INTEGER	read-write	This object indicates the applied protocol.
INT prtExPhPlConnectionTyp	1.3.6.1.4.1.164.3.2.3.2.3.1.1.8	INTEGER	read-write	This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management opration (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetMotMana - indicates network internal line, but the remote mux is not managed by the NMS. User - User to Network Interface. OtherNet - Network To Network Interface. PubNet - Access Mux To PubNet Interface.
INT prtExPhPlClkMode	1.3.6.1.4.1.164.3.2.3.2.3.1.1.9	INTEGER	read-write	Clock mode.
INT prtExPhPlDceClkSrc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.10	INTEGER	read-write	This attribute indicates the source of the clock when working in dce or ext-dce clock mode. notApplicable(1) - is applied for dte(3) and lbt(5) clock modes. When clock mode is dte, the clock source is always external, therefore this object's value is notApplicable. local(2) and nodalTiming(3) - are valid in dce(1), extDce(2) or int(4) clock modes. The recommended clock source is local(2).
INT prtExPhPlCongResponse	1.3.6.1.4.1.164.3.2.3.2.3.1.1.11	INTEGER	read-write	This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/received becn to/from the network). no - do nothing flowControl - translates the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done on both directions. toFlowControl- translates the backward congestion indication received from the internal connection port (normally the network side) to flow control and do nothing in the other direction.
I32 prtExPhPlCongLevel	1.3.6.1.4.1.164.3.2.3.2.3.1.1.12	Integer32	read-write	This attribute indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5 percent.
INT prtExPhPlTc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.13	INTEGER	read-write	This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports of a specific card .
INT prtExPhPlFlowControl	1.3.6.1.4.1.164.3.2.3.2.3.1.1.14	INTEGER	read-write	This attribute indicates the required flow control betweeen the port and the remote equipment. fecnBecn - is valid only for FR, FR+ and CR protocols. xonXoff,dtrCts - are valid only for Async protocols. speedReduction - is valid only for DLC protocol when the Clock Mode is DCE and the Clock Source is Local.
INT prtExPhPlDcdRts	1.3.6.1.4.1.164.3.2.3.2.3.1.1.15	INTEGER	read-write	Protocol may require end to end connect indication over the network. End to end link connection establishment over the FR network will be indicated to the user by using DCD or RTS control signals, depending on the clock mode: DCE or DTE respectively. The options are : - On : DCD(DCE)/RTS(DTE) will be constantly ON no matter if the End to End connection is established or not. - End to End: The DCD(DCE)/RTS(DTE) will be according to the status of the End to End connection.
INT prtExPhPlDcdRtsControlPath	1.3.6.1.4.1.164.3.2.3.2.3.1.1.16	INTEGER	read-write	Protocol may require end to end connect indication over the network. This parameter defines whether to take the user connection status (RTS(DCE)/DCD(DTE)) and forward it to the network side. - on : Transmit active connection to the network regardless the RTS/DCD control lines status. - off: Transmit active connection to the network according to the status of the RTS/DCD pin.
INT prtExPhPlDataBits	1.3.6.1.4.1.164.3.2.3.2.3.1.1.17	INTEGER	read-write	This attribute indicates the number of data bits in async frame. It is relevant only for Async protocols.
INT prtExPhPlParity	1.3.6.1.4.1.164.3.2.3.2.3.1.1.18	INTEGER	read-write	This attribute indicates the parity operation mode in async frame. It is relevant only for Async protocols.
INT prtExPhPlStopBits	1.3.6.1.4.1.164.3.2.3.2.3.1.1.19	INTEGER	read-write	This attribute indicates the minimum number of stop bits in the tx async frame. It is relevant only for Async protocols.
I32 prtExPhPlLXon	1.3.6.1.4.1.164.3.2.3.2.3.1.1.20	Integer32	read-write	This attribute indicates the character used as X-On to notify receive enable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable
I32 prtExPhPlLXoff	1.3.6.1.4.1.164.3.2.3.2.3.1.1.21	Integer32	read-write	This attribute indicates the character used as X-Off to notify receive disable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable
INT prtExPhPlFrMngProt	1.3.6.1.4.1.164.3.2.3.2.3.1.1.22	INTEGER	read-write	This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtExPhPlConnectionTyp = sameNetManaged, this object will be RO (internally determined).
I32 prtExPhPlEnqPeriod	1.3.6.1.4.1.164.3.2.3.2.3.1.1.23	Integer32	read-write	This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlFullRptPeriod	1.3.6.1.4.1.164.3.2.3.2.3.1.1.24	Integer32	read-write	This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlFrWindowSize	1.3.6.1.4.1.164.3.2.3.2.3.1.1.25	Integer32	read-write	This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlErrorsThreshold	1.3.6.1.4.1.164.3.2.3.2.3.1.1.26	Integer32	read-write	This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlPvcCreateMsg	1.3.6.1.4.1.164.3.2.3.2.3.1.1.27	INTEGER	read-write	This object is Update Message (if required or not). It determines whether a message of a New PVC Creation is requested or not (yes/no). Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlCllmMsg	1.3.6.1.4.1.164.3.2.3.2.3.1.1.28	INTEGER	read-write	This object is CLLM Message (if required or not). It determines whether to send (or not) a congestion message when the port is Rx congested. Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlProtDelayLevel	1.3.6.1.4.1.164.3.2.3.2.3.1.1.29	INTEGER	read-write	This object is the Segmentation in Bytes. In some cases, the enumerated values will mean other segmentation values than specified: Product: MX-3000 MX-3000 MX-300/MX-30 Protocol: FR+ Transparent FR+ ----------------------------------------------------- level 1 50 Bytes 44 Bytes 50 Bytes level 2 158 Bytes 155 Bytes 158 Bytes level 3 266 Bytes 266 Bytes 266 Bytes level 4 376 Bytes 377 Bytes 376 Bytes level 5 484 Bytes 488 Bytes 484 Bytes Defval=level 1 value This parameter is applicable only for FR+ and transparent protocols.
INT prtExPhPlClockEncoding	1.3.6.1.4.1.164.3.2.3.2.3.1.1.30	INTEGER	read-write	This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols. For MAXCESS 3000 & MP2100H: when setting to nrzI (3) the nrzI works as nrzI Mark. For MAXCESS 30/300 when setting to nrzI (3) the nrzI works as nrzI Space.
I32 prtExPhPlMinSeparators	1.3.6.1.4.1.164.3.2.3.2.3.1.1.31	Integer32	read-write	Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable
INT prtExPhPlCcittCrc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.32	INTEGER	read-write	This object indicates how many Bits are used for CRC (HDLC item).
INT prtExPhPlFrameSeparator	1.3.6.1.4.1.164.3.2.3.2.3.1.1.33	INTEGER	read-write	This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line.
I32 prtExPhPlIdleCode	1.3.6.1.4.1.164.3.2.3.2.3.1.1.34	Integer32	read-write	Determines the code for transmission when there are no frames to transmit on the line. The value should be 0 to FFH.
I32 prtExPhPlJitter	1.3.6.1.4.1.164.3.2.3.2.3.1.1.35	Integer32	read-write	Maximum variant delay of the FR network, in msec.
prtExPhPlDlciTable	1.3.6.1.4.1.164.3.2.3.2.3.2		not-accessible	The write operation into the Table Objects is valid only at the TmpCnfg entry.
prtExPhPlDlciEntry	1.3.6.1.4.1.164.3.2.3.2.3.2.1		not-accessible	An entry in table.
I32 prtExPhPlDlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExPhPlDlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPhPlDlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. PH.1/E1 and PH.1/T1 cards have three internal ports. Stand-alone units may have six such ports.
I32 prtExPhPlDlciIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, its type is 'user' and the only valid index is 1.
INT prtExPhPlDlciValid	1.3.6.1.4.1.164.3.2.3.2.3.2.1.5	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
INT prtExPhPlDlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.3.2.1.6	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. cl - will represent any of the CL slots. This value can be selected for multiple DLCIs of the product. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPhPlDlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.3.2.1.7	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to. clNMS - will be used for NMS SNMP messages. It can be any port of the CL card. This value will be selectable only if prtExPhPlDlciIConSlt='cl' or 'notApplicable'.
I32 prtExPhPlDlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.3.2.1.8	Integer32	read-write	This attribute indicates a unique internal connection dlci number, the dlci is routed to.
INT prtExPhPlDlciTxBc	1.3.6.1.4.1.164.3.2.3.2.3.2.1.9	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line).
INT prtExPhPlDlciTxBe	1.3.6.1.4.1.164.3.2.3.2.3.2.1.10	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line).
INT prtExPhPlDlciRxBc	1.3.6.1.4.1.164.3.2.3.2.3.2.1.11	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line).
INT prtExPhPlDlciRxBe	1.3.6.1.4.1.164.3.2.3.2.3.2.1.12	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line).
I32 prtExPhPlDlciPriority	1.3.6.1.4.1.164.3.2.3.2.3.2.1.13	Integer32	read-write	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority.
INT prtExPhPlDlciStatus	1.3.6.1.4.1.164.3.2.3.2.3.2.1.14	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
prtExPhPlModemTable	1.3.6.1.4.1.164.3.2.3.2.3.3		not-accessible	External Modem Parameters. The write operation into the Table Objects is valid only for the TmpCnfg entry.
prtExPhPlModemEntry	1.3.6.1.4.1.164.3.2.3.2.3.3.1		not-accessible	An entry in table.
I32 prtExPhPlModemCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExPhPlModemSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtExPhPlModemPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.3	INTEGER	read-only	This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid.
INT prtExPhPlModemStatus	1.3.6.1.4.1.164.3.2.3.2.3.3.1.4	INTEGER	read-write	This object indicates whether a Dial Up Modem is enabled on this port. Default: disable For Vmux devices this object shows whether there is Modem Relay support.
INT prtExPhPlModemActivate	1.3.6.1.4.1.164.3.2.3.2.3.3.1.5	INTEGER	read-write	This object indicates whether the Dial Up Modem is activated when the first frame is received or it is always activated. Default: onFirstFrame
I32 prtExPhPlModemMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.3.3.1.6	Integer32	read-write	Max Time allowed in Seconds without any traffic before the line is disconnected. Legal Values are: 1 sec, 2 sec .. 5 sec, 10 sec, 20 sec.. 1 min, 2 min .. 10 min, 15 min, 20 min, 25 min, 30 min. 65535 sec. means that this parameter is not applicable. Default: 1 sec.
I32 prtExPhPlModemTimeBtwnCalls	1.3.6.1.4.1.164.3.2.3.2.3.3.1.7	Integer32	read-write	Minimum Time in Seconds which is required after a call was disconnected. In this time no other call will be initiated from this Modem port even if there were frames transmitted to this port. This time is required for some Modems which have initializations that take a few seconds. Legal Values are: 0 sec. - 30 sec., 1-5 min. 65535 sec. means that this parameter is not applicable. Default: 0 sec
I32 prtExPhPlModemCallDelay	1.3.6.1.4.1.164.3.2.3.2.3.3.1.8	Integer32	read-write	Time in Seconds that the device will wait before dialing to the remote device. This feature is mostly used when there is a backup modem to the main link and the main link is down. In this case it is important to prevent the 2 devices from dialing through the backup modems to each other at the same time. It is advised to configure one side with a small call delay and the other side with a large call delay. Legal Values are: 0 - 30, 60, 120, 180, 240, 300, 600, 900, 1200, 1500, 1800 . 65535 sec. means that this parameter is not applicable. Default: 0 sec
prtLs2Cnfg	1.3.6.1.4.1.164.3.2.3.2.4
prtExLs2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.4.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExLs2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.4.1.1		not-accessible	An entry in table.
I32 prtExLs2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExLs2SltIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtExLs2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.3	INTEGER	read-only	This attribute indicates a unique port index. For the Ls2/X.58 exPrt(7)..exPrt(10) are not valid.
INT prtExLs2Connect	1.3.6.1.4.1.164.3.2.3.2.4.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs2Rate	1.3.6.1.4.1.164.3.2.3.2.4.1.1.5	INTEGER	read-write	Port rates.
INT prtExLs2ClkMode	1.3.6.1.4.1.164.3.2.3.2.4.1.1.6	INTEGER	read-write	This attribute indicates a unique port operation clock mode.
INT prtExLs2Cts	1.3.6.1.4.1.164.3.2.3.2.4.1.1.7	INTEGER	read-write	CTS.
INT prtExLs2Dcd	1.3.6.1.4.1.164.3.2.3.2.4.1.1.8	INTEGER	read-write	DCD.
I32 prtExLs2EnvIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.9	Integer32	read-write	Envelope Index. When prtInLs2EnvAssign=auto, the value is 0 (not applicable).
prtInLs2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.4.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInLs2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.4.2.1		not-accessible	An entry in table.
I32 prtInLs2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtInLs2SltIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtInLs2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port index.
INT prtInLs2Connect	1.3.6.1.4.1.164.3.2.3.2.4.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel.
I32 prtInLs2Group	1.3.6.1.4.1.164.3.2.3.2.4.2.1.5	Integer32	read-write	This attribute indicates the group number of the port. LS-2 internal ports with the same group number share the same Time slot of the main link
I32 prtInLs2Member	1.3.6.1.4.1.164.3.2.3.2.4.2.1.6	Integer32	read-write	This attribute indicates the group member id of the port. This parameter is for the automatic envelope assignment algorithm.
INT prtInLs2LinkTo	1.3.6.1.4.1.164.3.2.3.2.4.2.1.7	INTEGER	read-write	It indicates the slot of the main link card to which the LS2 card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInLs2EnvAssign	1.3.6.1.4.1.164.3.2.3.2.4.2.1.8	INTEGER	read-write	Envelope assignment type.
prtVc2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.5		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to prtVc2CnfgIdx=1.
prtVc2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.5.1		not-accessible	An entry in table.
I32 prtVc2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtVc2SltIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For Stand Alone products like WR: notApplicable (255)
I32 prtVc2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.3	Integer32	read-only	A unique identifier of the port, within the card. For MP-2100/2200 card ports, Web Ranger and FCD-IP Voice ports the values will be: exPrt1 (1) exPrt2 (2) exPrt3 (3) exPrt4 (4) exPrt5 (5) exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) exPrt10 (10) exPrt11 (11) exPrt12 (12) exPrt13 (13) exPrt14 (14) exPrt15 (15) exPrt16 (16) For LA-240: The index for fixed voice ports will be - exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) The index for voice card ports will be - Slot number * 100 + ch (for IO-1: 101..104, for IO-2: 201..204). For other products' index see their specification.
INT prtExVc2Connect	1.3.6.1.4.1.164.3.2.3.2.5.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
I32 prtExVc2TransGain	1.3.6.1.4.1.164.3.2.3.2.5.1.5	Integer32	read-write	Transmit gain in dBm. For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8 VC-4/Omni and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps.
I32 prtExVc2ReceiveGain	1.3.6.1.4.1.164.3.2.3.2.5.1.6	Integer32	read-write	Receive gain in dBm. For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8 VC-4/Omni and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps.
INT prtExVc2Wire	1.3.6.1.4.1.164.3.2.3.2.5.1.7	INTEGER	read-write	For some cards, this object is equal for all the ports in the specific card because of HW limitations. For FXO & FXS this parameter is not applicable.
INT prtExVc2CodingLaw	1.3.6.1.4.1.164.3.2.3.2.5.1.8	INTEGER	read-write	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations
INT prtExVc2Sig	1.3.6.1.4.1.164.3.2.3.2.5.1.9	INTEGER	read-write	This attribute indicates the method for decoding/encoding the signaling information(on/off hook). noSignaling (1) - not using signaling (only voice). robbedBitMultiFrame(2) - is the standard method for T1 links and proprietary method for E1 links. chAssociatedE1 (3) - is valid only for E1 G.732S links. robbedBitFrame (4) - is proprietary method implimenting 7 bit for the voice and 1 bit dedicated for signaling. For some cards, this object is equal for all the ports in the specific module because of HW limitations.
INT prtExVc2Oos	1.3.6.1.4.1.164.3.2.3.2.5.1.10	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
INT prtExVc2LinkTo	1.3.6.1.4.1.164.3.2.3.2.5.1.11	INTEGER	read-write	This attribute indicates the slot of the ML card to which the VC card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExVc2OperMode	1.3.6.1.4.1.164.3.2.3.2.5.1.12	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request.
INT prtExVc2SigProfile	1.3.6.1.4.1.164.3.2.3.2.5.1.13	INTEGER	read-write	This object indicates the Signaling Profile of the port. notApplicable - for VC-2 family and when prtExVc2Sig=noSignaling(1) p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4
INT prtExVc2CallEnable	1.3.6.1.4.1.164.3.2.3.2.5.1.14	INTEGER	read-write	This object indicates the Enabled Call direction. notApplicable - for all cards except VC-2/R2. both - incoming + outgoing.
INT prtExVc2R2Delay	1.3.6.1.4.1.164.3.2.3.2.5.1.15	INTEGER	read-write	This object indicates the R2 Delay. notApplicable - for all cards except VC-2/R2.
INT prtExVc2CasStd	1.3.6.1.4.1.164.3.2.3.2.5.1.16	INTEGER	read-write	This object indicates the CAS (Channel Associated Signaling) Standard. notApplicable - for all cards except VC-2/R2.
INT prtExVc2EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.5.1.17	INTEGER	read-write	Echo canceler activation. notApplicable - for VC-2 and VC-6 cards.
INT prtExVc2IfType	1.3.6.1.4.1.164.3.2.3.2.5.1.18	INTEGER	read-write	Interface Type.
INT prtExVc2Encoding	1.3.6.1.4.1.164.3.2.3.2.5.1.19	INTEGER	read-write	Voice Encoding Mode. linear - is relevant only for the ports of VC-16A card.
OCT prtExVc2TxBitCode	1.3.6.1.4.1.164.3.2.3.2.5.1.20	OCTET STRING	read-write	- - - For MP & FCD - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = M lead 2 hex = 0010 = M lead inverse 3 hex = 0011 = Reverse Polarity 4 hex = 0100 = Metering Pulse 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For WR II - - - This object represents the following 4 parameters by 2 Octets: 1. On/Off hook signaling transmission mode from the FXS towards the T1/E1 (MSB nibble 1). 2. Default signaling bits that are not in use (nibble 2). 3. Ring Detection signaling transmission mode from the FXO towards the T1/E1(nibble 3). 4. M (Mouth) Signaling transmission mode from the E&M towards the T1/E1(LSB nibble 4). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook Default sig. Ring Detect. M (Mouth) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable. Not Applicable Not Applicable 1 hex = 0001 Tx A bit Values 1-3 are Tx A bit Tx A bit 2 hex = 0010 Tx A bit inverse for On/Off Hook Tx A bit inv. Tx A bit inv. 3 hex = 0011 Tx B bit A,B,A Inv,B Inv. Tx B bit Tx B bit 4 hex = 0100 Tx B bit inverse Values 4-7 are Tx B bit inv. Tx B bit inv. 5 hex = 0101 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid 6 hex = 0110 not Used-invalid A, A Inverse. not Used-invalid not Used-invalid 7 hex = 0111 not Used-invalid not Used-invalid not Used-invalid 8 hex = 1000 not Used-invalid Values 8-11 are not Used-invalid not Used-invalid 9 hex = 1001 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid A hex = 1010 not used-invalid B, B Inverse. not Used-invalid not Used-invalid B hex = 1011 not used-invalid The Bits order: not Used-invalid not Used-invalid C-F hex not used-invalid ABCD not Used-invalid not Used-invalid Default value: 11 11
OCT prtExVc2RxBitOutput	1.3.6.1.4.1.164.3.2.3.2.5.1.21	OCTET STRING	read-write	- - - For MP (VC-Q card only) & FCD - - - This object represents 3 parameters by 2 Octets: Spare -MSB nibble, always=0 hex E Lead Output - nibble, Reverse Polarity Output- nibble, Metering Pulse Output -LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = Rx A bit 2 hex = 0010 = Rx A bit inverse 3 hex = 0011 = Rx B bit 4 hex = 0100 = Rx B bit inverse 5 hex = 0101 = Rx C bit 6 hex = 0110 = Rx C bit inverse 7 hex = 0111 = Rx D bit 8 hex = 1000 = Rx D bit inverse 9 hex = 1001 = none A-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For MP (VC-8, VC-16, VC-16A cards) - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = not used (invalid value) 2 hex = 0010 = not used (invalid value) 3 hex = 0011 = not used (invalid value) 4 hex = 0100 = not used (invalid value) 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO. - - - For WR II - - - This object represents the following 2 parameters in 1 Octet: 1. On/Off hook signaling receive mode from the T1/E1 into the FXS/FXO (MSB nibble 1). 2. E (Ear) Signaling receive mode from the T1/E1 into the E&M (LSB nibble 2). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook E (Ear) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable 1 hex = 0001 Rx A bit Rx A bit 2 hex = 0010 Rx A bit inverse Rx A bit inverse 3 hex = 0011 Rx B bit Rx B bit 4 hex = 0100 Rx B bit inverse Rx B bit inverse 5-F hex not used-invalid not Used-invalid Default value: 11
INT prtExVc2MeterRate	1.3.6.1.4.1.164.3.2.3.2.5.1.22	INTEGER	read-write	This entry is applicable only for VC-6A/FXO, VC-6A/FXS, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS. Meter Rate means rate of Call Meter in Public Phones, in KHz units. For some cards, the value must be the same for all card's ports.
INT prtExVc2IfSignaling	1.3.6.1.4.1.164.3.2.3.2.5.1.23	INTEGER	read-write	This entry is applicable only for VC-6A, VC-6AG, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS cards. Interface Analog Signaling. Must be the same for all card's ports. loopStart - for the usual trunk/phone types. groundStart - for trunks that need Ground signaling . winkStart - for trunks that need Reverse Polarity.
INT prtExVc2SeizeAck	1.3.6.1.4.1.164.3.2.3.2.5.1.24	INTEGER	read-write	This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Default value for WR FXO: no(2).
INT prtExVc2EandMType	1.3.6.1.4.1.164.3.2.3.2.5.1.25	INTEGER	read-write	This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters.
INT prtExVc2RemType	1.3.6.1.4.1.164.3.2.3.2.5.1.26	INTEGER	read-write	Remote Type. Applicable for VC-6A/4LB card & for IPMUX-1E Far End Type - E1,T1(T1-ESF) or T1-D4 .
INT prtExVc2ConvTime	1.3.6.1.4.1.164.3.2.3.2.5.1.27	INTEGER	read-write	Conversation Time in minutes. Applicable for VC-6A/4LB card.
INT prtExVc2SigFeedback	1.3.6.1.4.1.164.3.2.3.2.5.1.28	INTEGER	read-write	Signaling Feedback. Applicable for VC-8/FXO and VC-16/FXO cards.
INT prtExVc2EchoCancelerModule	1.3.6.1.4.1.164.3.2.3.2.5.1.29	INTEGER	read-only	This parameter indicates whether Echo canceler module exists for this port.
INT prtExVc2ReversePolarity	1.3.6.1.4.1.164.3.2.3.2.5.1.30	INTEGER	read-write	This object Enables/Disables Reverse Polarity for this port.
INT prtExVc2RingerFrequency	1.3.6.1.4.1.164.3.2.3.2.5.1.31	INTEGER	read-write	This object selects the Ringer Frequency (Hz) for this port.
INT prtExVc2SigService	1.3.6.1.4.1.164.3.2.3.2.5.1.32	INTEGER	read-write	Signaling Service. advanced - is relevant only for ports of VC-8, VC-16 FXS cards. It is used for Signaling Services of V5.1 or R2.
INT prtExVc2CallerIdEnable	1.3.6.1.4.1.164.3.2.3.2.5.1.33	INTEGER	read-write	This object Enables/Disables Receiving the Caller Id number from the remote side, for this port/channel.
INT prtExVc2CompressMethod	1.3.6.1.4.1.164.3.2.3.2.5.1.34	INTEGER	read-write	This object is applicable only when prtExVc2Encoding=adpcm. It defines which method is used for Compression. g726 - for 4 bits (the standard method). g726 - for 3 bits. It is especially needed for T1 applications with signaling.
INT prtExVc2ObMode	1.3.6.1.4.1.164.3.2.3.2.5.1.35	INTEGER	read-write	This object defines the Net operation mode of the Omni-Bus card's port. pointToPoint - only 2 end-point ports talk; like any other voice card omniBus - many talk and listen. Like conference call. All can listen to all. pointToMultiPointSrc - There is one Master who can be heard by all. All can talk, but only the Master can hear all. Others can hear only the Master. This port is of the Master (Src). pointToMultiPointDst - There is one Master who can be heard by all. All can talk, but only the Master can hear all. Others can hear only the Master. This port is of a Destination (NOT Master).
INT prtExVc2VAD	1.3.6.1.4.1.164.3.2.3.2.5.1.36	INTEGER	read-write	This object defines whether Voice Activation Detector (VAD) will be On or Off. off - will be usually selected when a Modem is connected to the port; not a phone. notApplicable - when prtExVc2DspMode=pointToPoint.
INT prtExVc2NoiseLevelForVAD	1.3.6.1.4.1.164.3.2.3.2.5.1.37	INTEGER	read-write	This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to deal with. notApplicable - when prtExVc2VAD=off.
INT prtExVc2WesternSigMode	1.3.6.1.4.1.164.3.2.3.2.5.1.38	INTEGER	read-write	This object defines the Western Signaling Mode. detector - detects signal and passes it as is. generator - generates the signal. notApplicable - when Western HW is not installed.
INT prtExVc2BusProtectionPoint	1.3.6.1.4.1.164.3.2.3.2.5.1.39	INTEGER	read-write	This object defines if the port is Bus Protection Point or not. notApplicable - when prtExVc2DspMode=pointToPoint. When we have a chain of devices where the edge devices ports are the Bus Protection Point, user must configure one of these ports as 'first' and the other as 'last'. It does not matter which one, it just matters that they will be different.
INT prtExVc2ImpedanceStandard	1.3.6.1.4.1.164.3.2.3.2.5.1.40	INTEGER	read-write	This object defines the Standard used for Impedance. -G.712 - 600 Ohm - used in USA and other countries. -Q552/ETSI - used in some countries in Europe -Q522/Italy - used in Italy.
prtHsfCnfgTable	1.3.6.1.4.1.164.3.2.3.2.6		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtHsfCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.6.1		not-accessible	An entry in table.
I32 prtHsfCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relate to the TmpCnfg.
INT prtHsfSltIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtHsfPrtIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.3	INTEGER	read-only	This attribute indicates a unique external port index. Hs2 has only two ports (exPrt1,exPrt2). Hs3 has three ports (exPrt1,exPrt2,exPrt3). Hsq and hsqN has four ports. Hs6 has six external ports. Hs12 has twelve external ports. inPrt1, inPrt2 - are relevant for VID card.
INT prtExHsfConnect	1.3.6.1.4.1.164.3.2.3.2.6.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExHsfRate	1.3.6.1.4.1.164.3.2.3.2.6.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtExHsfClkMode	1.3.6.1.4.1.164.3.2.3.2.6.1.6	INTEGER	read-write	This attribute indicates a unique port operation clock mode.
INT prtExHsfCts	1.3.6.1.4.1.164.3.2.3.2.6.1.7	INTEGER	read-write	This attribute indicates a unique CTS control line operation mode.
INT prtExHsfFifoSize	1.3.6.1.4.1.164.3.2.3.2.6.1.8	INTEGER	read-write	Size in bits.
INT prtExHsfLinkTo	1.3.6.1.4.1.164.3.2.3.2.6.1.9	INTEGER	read-write	This attribute indicates a slot of Main Link module, that the port is linked to. This object is the same for all the ports in the specific card because of HW limitations. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExHsfOperMode	1.3.6.1.4.1.164.3.2.3.2.6.1.10	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request. bidirBcastRing = Bidirectional Broadcast Ring. When this value is selected, AND RTS=On, the port opens its transmission channel.
INT prtExHsfInbandLoopback	1.3.6.1.4.1.164.3.2.3.2.6.1.11	INTEGER	read-write	This object indicates if Inband Loopback from the Network should be enabled or disabled.
INT prtExHsfClkPolarity	1.3.6.1.4.1.164.3.2.3.2.6.1.12	INTEGER	read-write	This object indicates the clock polarity. For FCD-M this object will be applicable only for the fixed HS port (the fixed port on the device).
INT prtExHsfControlSignal	1.3.6.1.4.1.164.3.2.3.2.6.1.13	INTEGER	read-write	This object indicates the Control Signal according to G.797 ITU-T standard. For FCD-M this object will be applicable for the fixed HS port (the fixed port on the device) and HS-Q/N channels. Local and End to End are applicable only when channel Interface type is RS-530, else it will be Not Applicable.
INT prtExHsfBcastRingSrcPort	1.3.6.1.4.1.164.3.2.3.2.6.1.14	INTEGER	read-write	This object is applicable only when prtExHsfOperMode= bidirBcastRing. In this case, the values mean: - none - this port will be connected to ML in TSA as usual. - exPrt1.. exPrtX ; X=maximum ports of the card in focus : it means that the same TS that is assigned in TSA to this port is actually connected also to this port, for Broadcast Ring mode. Therefore, this port should NOT be connected to ML in TSA.
prtHs4Cnfg	1.3.6.1.4.1.164.3.2.3.2.7
prtExHs4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.7.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExHs4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.7.1.1		not-accessible	An entry in table.
I32 prtExHs4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExHs4SltIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
INT prtExHs4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExHs4Connect	1.3.6.1.4.1.164.3.2.3.2.7.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithm. It also affects all the module considerations because the card has only one external (physical) interface.
INT prtExHs4LineType	1.3.6.1.4.1.164.3.2.3.2.7.1.1.5	INTEGER	read-write	This attribute is the line type parameter for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the HS-4/1 and E1 line code parameters for the HS-4/2. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) dsx1ESF (2) dsx1D4 (3) dsx1E1 (4) dsx1E1-CRC (5) dsx1E1-MF (6) dsx1E1-MF-CRC (7)
INT prtExHs4LineCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.6	INTEGER	read-write	This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the MPH.1/T1 and E1 line code parameters for the MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExHs4LineLen	1.3.6.1.4.1.164.3.2.3.2.7.1.1.7	INTEGER	read-write	This attribute is the line length parameter used only for T1 interfaces. len399p533ft=len-399-533ft
INT prtExHs4RestoreT	1.3.6.1.4.1.164.3.2.3.2.7.1.1.8	INTEGER	read-write	Time passing from the disappearance of the loss of synchronization condition (red alarm), to the restoration of normal service.
INT prtExHs4OosSig	1.3.6.1.4.1.164.3.2.3.2.7.1.1.9	INTEGER	read-write	Out of Service signal type.
INT prtExHs4OosCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.10	INTEGER	read-write	OOS Code
I32 prtExHs4IdleCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.11	Integer32	read-write	Type value(00 - FF HEX), excluding 0H,8H,10H,12H,21H,24H, 42H,49H,84H,92H
INT prtExHs4MfClkSrcSlt	1.3.6.1.4.1.164.3.2.3.2.7.1.1.12	INTEGER	read-write	This attribute indicates whether the port Tx is multiframe synchronized with Rx multiframe of another port and the slot position of that port. This opration is required in order to bypass signaling of PCM voice channels. When its value is Local(2) there is no meaning to 'prtExHs4MfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExHs4MfClkSrcPrt	1.3.6.1.4.1.164.3.2.3.2.7.1.1.13	INTEGER	read-write	A unique number to identify a port position in the mux if the MultiFrame clock source is valid (YES). inPrt1 - for MTML-H/E1 cards.
prtExHs4TsCnfgTable	1.3.6.1.4.1.164.3.2.3.2.7.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExHs4TsEntry	1.3.6.1.4.1.164.3.2.3.2.7.2.1		not-accessible	An entry in table.
I32 prtExHs4TsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExHs4TsSltIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExHs4TsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.3	INTEGER	read-only	This attribute indicates a unique port number. Hs4/T1 and Hs4/T1 cards have only one external interface.
I32 prtExHs4TsIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling.
INT prtExHs4TsIConSlot	1.3.6.1.4.1.164.3.2.3.2.7.2.1.5	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS).
INT prtExHs4TsIConPrt	1.3.6.1.4.1.164.3.2.3.2.7.2.1.6	INTEGER	read-write	This attribute indicates the internally (In Mux) connected/routed port.
I32 prtExHs4TsIConTs	1.3.6.1.4.1.164.3.2.3.2.7.2.1.7	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Module and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
prtHsiCnfg	1.3.6.1.4.1.164.3.2.3.2.8
prtExHsiCnfgTable	1.3.6.1.4.1.164.3.2.3.2.8.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExHsiCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.8.1.1		not-accessible	An entry in table.
I32 prtExHsiCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExHsiSltIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
I32 prtExHsiPrtIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.3	Integer32	read-only	A unique port identifier within the card. For MP : 1..12 For DXC: 111 .. 2531. See DXC R6 spec for port index convention. For FCD-A, 'S' Interface external ports: 131, 141, 151, 161.
INT prtExHsiConnect	1.3.6.1.4.1.164.3.2.3.2.8.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. v51 - this port is connected to a V5.1 interface. All rest of the values will be 'notApplicable' in this case. V5 MIB will be used instead. v52 - this port is connected to a V5.2 interface. All rest of the values will be 'notApplicable' in this case. V5 MIB will be used instead.
INT prtExHsiRate	1.3.6.1.4.1.164.3.2.3.2.8.1.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtExHsiLinkTo	1.3.6.1.4.1.164.3.2.3.2.8.1.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the HS-? card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExHsiInterface	1.3.6.1.4.1.164.3.2.3.2.8.1.1.7	INTEGER	read-write	It indicates the interface type: lt = line termination nt = network termination te = terminal equipment. lt1 - for ASMi-31 connection (not ISDN) For MP: For HS-U/I only 'lt' and 'nt' are applicable. For HS-U/1 only 'lt' is applicable. For HS-S , only 'te' and 'nt' are applicable. For HS-U, this object is not applicable. For HS-U6, HS-U12, are applicable: 'lt'=lt-i,'nt'=nt-i, lt1. For DXC: For HS-U8, HS-U16, are applicable: 'lt'=LT-I,'nt'=NT-I, 'lt1'=LT-1.
INT prtExHsiActType	1.3.6.1.4.1.164.3.2.3.2.8.1.1.8	INTEGER	read-write	It indicates the Activation Type. Activation Type is the Synchronization type towards the PBX. It is applicable only when prtExHsiInterface=nt. notApplicable - for cards that do not support this object, or when prtExHsiInterface is NOT nt.
prtInHsiCnfgTable	1.3.6.1.4.1.164.3.2.3.2.8.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. This table is not applicable for MP-2100 HS-U card type.
prtInHsiCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.8.2.1		not-accessible	An entry in table.
I32 prtInHsiCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtInHsiSltIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted.
I32 prtInHsiPrtIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.3	Integer32	read-only	A unique port identifier within the card. Valid values for MP: inPrt1 (101) .. inPrt48 (148). Valid values for DXC: 11012.. 25316. See DXC R6 spec for port index convention.
INT prtInHsiConnect	1.3.6.1.4.1.164.3.2.3.2.8.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInHsiRate	1.3.6.1.4.1.164.3.2.3.2.8.2.1.5	INTEGER	read-write	This object indicates the port speed. For HS-U/I and HS-S ports: 2 bit - up to 9600bps 4 bit - 19200bps 8 bit - 38400bps .. 64kbps. concentrated - this D channel goes to a Concentration channel, that represents many channels that this value was selected for them. The Concentrated channel is an Internal D Channel of the same card. This value is applicable only for D channels, except Concentration channel itself. --for HS-S and HS-U/I cards the Concentration channel will always be: internal-13 --for MP-2200 HS-S12, HS-S6, HS-U12, HS-U6 and DXC HS-U8 and HS-U16 cards, the Concentration channel is selected via the prtInHsiConcentratedTo object. notConnected - same as prtInHsiConnect=no.
I32 prtInHsiConcentratedTo	1.3.6.1.4.1.164.3.2.3.2.8.2.1.6	Integer32	read-write	The Concentration D Channel of the prtInHsiPrtIdx port. The port always belongs to the same card as prtInHsiPrtIdx port. This object is applicable only when prtInHsiRate=concentrated. Valid values: - notApplicable: 255 - for MP-2200: HS-S12, HS-U12 cards: inPrt37 (137) .. inPrt48 (148). HS-S6, HS-U6 cards: inPrt19 (119) .. inPrt24 (124). - for DXC: HS-U8 cards: 112 .. 254 HS-U16 cards: 112 .. 258. See DXC R6 spec for port index convention.
prtPVc4Cnfg	1.3.6.1.4.1.164.3.2.3.2.9
prtExPVc4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.9.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExPVc4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.9.1.1		not-accessible	An entry in table.
I32 prtExPVc4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExPVc4SltIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
INT prtExPVc4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.3	INTEGER	read-only	This object indicates the port number in the selected card (slot).
INT prtExPVc4PrtType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.4	INTEGER	read-write	This object indicates the type of the selected port. In Mx 30/300 phase 4: s0 & u are for Voice over ISDN. In MX 30/300 phase 5: sQsig & uQsig are used for Voice over ISDN with Qsig option. In MX MVC4 voice cards, each pair of ports 1-2, 3-4 may have a different type: E&M, FXO, FXS. In MVC4 compressed voice cards ports 1..4 have the same interface for all ports. In MVC8 compressed voice cards each group of ports 1..4, 5..8 may have a different type: E&M, FXO, FXS.
INT prtExPVc4Connect	1.3.6.1.4.1.164.3.2.3.2.9.1.1.5	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExPVc4IfType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.6	INTEGER	read-write	This attribute indicates the interface type of the port. eAndM4wires and eAndM2wires - are valid only for E&M port type eAndM4wires - means 2/4 wires fxoGnd and fxoLoop - are valid only for FXO port type fxsGnd and fxsLoop - are valid only for FXS port type e1Framer, e1Slave, t1Framer, t1Slave - are applicable for the mvc4Pbx cards only.
I32 prtExPVc4TxGain	1.3.6.1.4.1.164.3.2.3.2.9.1.1.7	Integer32	read-write	Transmission gain in dB.
I32 prtExPVc4RxGain	1.3.6.1.4.1.164.3.2.3.2.9.1.1.8	Integer32	read-write	Reception gain in dBm.
INT prtExPVc4MaxRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.9	INTEGER	read-write	Voice rate.
INT prtExPVc4Tc	1.3.6.1.4.1.164.3.2.3.2.9.1.1.10	INTEGER	read-write	Time interval for CIR control, in seconds. The value will be the same for all cards' ports.
INT prtExPVc4Oos	1.3.6.1.4.1.164.3.2.3.2.9.1.1.11	INTEGER	read-write	Handling type, when connection is lost.
INT prtExPVc4EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.9.1.1.12	INTEGER	read-write	Echo canceler activation.
I32 prtExPVc4VarDelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.13	Integer32	read-write	Maximum variant delay of the FR network, in msec.
I32 prtExPVc4CongLevel	1.3.6.1.4.1.164.3.2.3.2.9.1.1.14	Integer32	read-write	This object indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5%.
INT prtExPVc4Wire	1.3.6.1.4.1.164.3.2.3.2.9.1.1.15	INTEGER	read-write	This object indicates the wiring of the E&M port. It is applicable only for E&M card type.
INT prtExPVc4ExtensionType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.16	INTEGER	read-write	This object indicates the type of extension relevant for this port. ipForceConnect (6) is used for automatic connection or automatic dialing when the phone is off hook (hot line). permanentDial (7) means that the call is established upon power up. The hook may be on or off. Permanent Dialing can be used when there is no signaling. autoAccept (8) means that the called party in the Permanent Dialing will accept the call from the remote side automatically upon on or off hook.
STR prtExPVc4ExtensionNumber	1.3.6.1.4.1.164.3.2.3.2.9.1.1.17	DisplayString	read-write	This is the extension number of this port. This field is relevant only when the extension type is voice switching and is read only if the port is member of a hunt group.
INT prtExPVc4OutPulsing	1.3.6.1.4.1.164.3.2.3.2.9.1.1.18	INTEGER	read-write	This field indicates whether to outpulse the received digits. It is notApplicable(1) when the extension type is forceConnect(2).
INT prtExPVc4HuntGroupMb	1.3.6.1.4.1.164.3.2.3.2.9.1.1.19	INTEGER	read-write	This object indicates if this port belongs to an hunt group.
I32 prtExPVc4HuntGroupIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.20	Integer32	read-write	If it belongs to an hunt group, this fields indicates the index of the relevant hunt group. 0 = notApplicable
INT prtExPVc4AutoFaxMode	1.3.6.1.4.1.164.3.2.3.2.9.1.1.21	INTEGER	read-write	This object indicates if the system will switch automatically to FAX mode when detecting FAX activity. Default=Yes.
INT prtExPVc4FaxRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.22	INTEGER	read-write	FAX initial rate. Default=9600 bps.
INT prtExPVc4SeizeAck	1.3.6.1.4.1.164.3.2.3.2.9.1.1.23	INTEGER	read-write	This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Example: If Seize Ack Parameter = YES, when the MVC.4 receives a seize signal (Off Hook) from the PBX it will send an Off Hook to the PBX. The Seize Parameter is relevant for all the following cards: MVC-4 MVC-4/E1-Framer MVC-4/T1-DSU-Framer MVC-4/T1-CSU-Framer MVC-4/E1-SLAVE MVC-4/T1-SLAVE Default values: Analog FXS - No (value can't be changed). Analog FXO - Yes (value can't be changed). Analog E&M - No (values NO/YES). Digital E1/T1 Framer & Slave - No.
INT prtExPVc4SignalingProtocol	1.3.6.1.4.1.164.3.2.3.2.9.1.1.24	INTEGER	read-write	The signaling protocol that will be used between the PABX & the voice port. Delay Start Protocol: the line is seized by sending an Off hook signal and after a delay, if the called party is available (On hook) DTMF (Dual Tone Multi Frequency) digits are sent towards the called party. Immediate Start Protocol: the line is seized by sending an Off Hook signal and immediately DTMF digits are sent towards the called party. Wink start protocol: the line is seized by sending an Off Hook signal and then the called party sends a short Off Hook wink signal. Now the calling party starts sending DTMF digits.
I32 prtExPVc4DelayStart	1.3.6.1.4.1.164.3.2.3.2.9.1.1.25	Integer32	read-write	This parameter is used only for Delay Protocol. This is the time that the calling party will wait after sending an Off hook signal and before sending DTMF digits to the called party. The delay values are 100..5000 msec in intervals of 100 msec.
I32 prtExPVc4WinkMinDuration	1.3.6.1.4.1.164.3.2.3.2.9.1.1.26	Integer32	read-write	This parameter is used only for Wink Protocol. Min Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec.
I32 prtExPVc4WinkMaxDuration	1.3.6.1.4.1.164.3.2.3.2.9.1.1.27	Integer32	read-write	This parameter is used only for Wink Protocol. Max Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec.
INT prtExPVc4GenerateTone	1.3.6.1.4.1.164.3.2.3.2.9.1.1.28	INTEGER	read-write	This parameter indicates whether the device (MX or MPH) should generate dial tones for the channel. If the value is yes (3), it generates dial tones. If the value is no (2), the connected equipment will generate dial tones. For example for some ISDN sets the dial tone is generated by the phone itself while for others sets it is generated by the MX.
INT prtExPVc4CodingLaw	1.3.6.1.4.1.164.3.2.3.2.9.1.1.29	INTEGER	read-write	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations
INT prtExPVc4GenerateRingBack	1.3.6.1.4.1.164.3.2.3.2.9.1.1.30	INTEGER	read-write	Determines whether the Ring Back tone is generated locally or from the remote end. The default is - NO (Meaning coming from the remote end). Yes means that the Ring Back Tone is generated locally. Applicable only for Force Connect.
I32 prtExPVc4ChannelId	1.3.6.1.4.1.164.3.2.3.2.9.1.1.31	Integer32	read-write	Channel Identifier. According to FRF11 each voice port that works as force connect should add a CH Id after the DLCI in the frame header. Default : 1 Applicable only for Force Connect. Not Applicable value will be 0.
INT prtExPVc4PortConnection	1.3.6.1.4.1.164.3.2.3.2.9.1.1.32	INTEGER	read-write	Port connection determines whether the port is connected to a PABX (Trunk) or to Telephone set (Line) . It determines whether to send certain messages to the port or not. If the type is LINE then the port generates a ring back tone , if TRUNK it doesn't (The PBX does it).
INT prtExPVc4CoderAndRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.33	INTEGER	read-write	Coder and Rate for the Voice Compression. In MPH: Relevant for MVC-8 card only.
STR prtExPVc4DestinationNum	1.3.6.1.4.1.164.3.2.3.2.9.1.1.34	DisplayString	read-write	The destination phone number: 0 to 22 digits. Applicable for Auto Dial - ipForceConnect(6), Permanent Dial and Auto Accept Extension Types. Default: Null String
INT prtExPVc4DtmfRelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.35	INTEGER	read-write	When DTMF RELAY is disabled, the DTMF digits (dialed by the user) are transmitted as compressed voice and in the remote unit are decompressed. When DTMF RELAY is enabled, the DTMF digits are detected at the near side and not transmitted as voice. Instead, only an indication of what digits were dialed are transmitted and in the far end the tone is regenerated.
I32 prtExPVc4DiscOnSilence	1.3.6.1.4.1.164.3.2.3.2.9.1.1.36	Integer32	read-write	No. of silenced seconds after which the call will be disconected. A value of 0 means that there will be no disconnect when there is silence. Possible values: 0 - 900 sec.
INT prtExPVc4DynamicJitter	1.3.6.1.4.1.164.3.2.3.2.9.1.1.37	INTEGER	read-write	The MVC8 uses two mechanisms to overcome the network delay. The first one is a static jitter buffer which holds a constant buffer of up to 300 Msec and can be controled by the JITTER parameter (prtExPVc4VarDelay). The second one is the dynamic jitter which calculates, in real time, the network delay and handles a jitter buffer dynamically. The dynamic mechanism that is implemented in MVC8, was intended to overcome network delay yet when the network bursts, the MVC8 dynamic mechanism is not able to overcome the delay. Therefore it is better not to use the dynamic jitter (DISABLE - should be the default) where bursts may occur often.
INT prtExPVc4EandMType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.38	INTEGER	read-write	This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters.
I32 prtExPVc4Rate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.39	Integer32	read-write	This is the Rate of the port in TS units. It is used by VF-30 card family. 0 = NA = port is not intended to be connected; therefore, no Rate.
I32 prtExPVc4FrameSize	1.3.6.1.4.1.164.3.2.3.2.9.1.1.40	Integer32	read-write	Defines the maximum size in Bytes of the multiplexed frame. In some cases this must be limited to avoid IP fragmentation, which makes the multiplexing useless, and can also decrease the damage in case of frame loss. Valid range: 100..1461. notApplicable=0.
I32 prtExPVc4MultiplexInterval	1.3.6.1.4.1.164.3.2.3.2.9.1.1.41	Integer32	read-write	Defines the maximum amout of time (msec.) between multiplexed frames that are sent. For Vmux-400/420 devices: It defines the Payload Packetizing Interval. Valid values: 10-90 msec. notApplicable=0.
INT prtExPVc4TransportProtocol	1.3.6.1.4.1.164.3.2.3.2.9.1.1.42	INTEGER	read-write	Transport Protocol. ptp = point to point. aal2oMpls = AAL2 over MPLS.
INT prtExPVc4MultiFreqRelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.43	INTEGER	read-write	This object enables/disables Multi Frequency Signaling Detection.
I32 prtExPVc4MinPulseWidth	1.3.6.1.4.1.164.3.2.3.2.9.1.1.44	Integer32	read-write	Defines the minimum Pulse Width in msec. Valid values: 45-100 msec. notApplicable=0.
I32 prtExPVc4MinPowerLevel	1.3.6.1.4.1.164.3.2.3.2.9.1.1.45	Integer32	read-write	Defines the minimum Power Level in dBm. Valid values: -1..-35 dBm.
INT prtExPVc4SuperTandem	1.3.6.1.4.1.164.3.2.3.2.9.1.1.46	INTEGER	read-write	The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem, when enabled, allows transmission of compressed voice between a few devices and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay.
IP prtExPVc4DestIp	1.3.6.1.4.1.164.3.2.3.2.9.1.1.47	IpAddress	read-write	This object defines the destination IP Address.
I32 prtExPVc4DestBundle	1.3.6.1.4.1.164.3.2.3.2.9.1.1.48	Integer32	read-write	This object defines the destination Bundle at the far-end device.
IP prtExPVc4SrcIpAddress	1.3.6.1.4.1.164.3.2.3.2.9.1.1.49	IpAddress	read-write	This object defines the Source IP Address.
IP prtExPVc4SrcIpMask	1.3.6.1.4.1.164.3.2.3.2.9.1.1.50	IpAddress	read-write	This object defines the Source IP Mask.
IP prtExPVc4DefaultGateway	1.3.6.1.4.1.164.3.2.3.2.9.1.1.51	IpAddress	read-write	This object defines the Default Gateway for this interface.
U32 prtExPVc4SigPacketInterval	1.3.6.1.4.1.164.3.2.3.2.9.1.1.52	Unsigned32	read-write	Defines the Signaling Packetizing Interval, which is the maximum time interval, measured in msec (milliseconds), between multiplexed signaling frames.
prtExPVc4DlciTable	1.3.6.1.4.1.164.3.2.3.2.9.2		not-accessible	The write operation into the Table Objects is valid only at the TmpCnfg entry.
prtExPVc4DlciEntry	1.3.6.1.4.1.164.3.2.3.2.9.2.1		not-accessible	An entry in table.
I32 prtExPVc4DlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExPVc4DlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPVc4DlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. VC4 cards have four external ports.
INT prtExPVc4DlciValid	1.3.6.1.4.1.164.3.2.3.2.9.2.1.4	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
INT prtExPVc4DlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.9.2.1.5	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPVc4DlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.9.2.1.6	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to.
I32 prtExPVc4DlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.9.2.1.7	Integer32	read-write	This attribute indicates a unique internal connection dlci number, the dlci is routed to.
INT prtExPVc4DlciTxBc	1.3.6.1.4.1.164.3.2.3.2.9.2.1.8	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line).
INT prtExPVc4DlciTxBe	1.3.6.1.4.1.164.3.2.3.2.9.2.1.9	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line).
INT prtExPVc4DlciRxBc	1.3.6.1.4.1.164.3.2.3.2.9.2.1.10	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line).
INT prtExPVc4DlciRxBe	1.3.6.1.4.1.164.3.2.3.2.9.2.1.11	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line).
I32 prtExPVc4DlciPriority	1.3.6.1.4.1.164.3.2.3.2.9.2.1.12	Integer32	read-write	This attribute indicates a unique priority of the pvc. 6 is the lowest priority and 8 is the highest priority.
INT prtExPVc4DlciStatus	1.3.6.1.4.1.164.3.2.3.2.9.2.1.13	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
prtHsrCnfg	1.3.6.1.4.1.164.3.2.3.2.10
prtExHsrCnfgTable	1.3.6.1.4.1.164.3.2.3.2.10.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExHsrCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.10.1.1		not-accessible	An entry in table.
I32 prtExHsrCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExHsrSltIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted.
I32 prtExHsrPrtIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.3	Integer32	read-only	A unique prt identifier within the card. Valid values: For MP: - For HS-R cards: exPrt1 (1) .. exPrt4 (4) - For HS-U/1 cards: inPrt1 (101) .. inPrt4 (104) - For HS-S12, HS-S6, HS-U12, HS-U6 cards: exPrt1 (1) .. exPrt12 (12). This MIB table is used only for LT-1 interface. For DXC: - For HS-U8, HS-U16 cards: 111 .. 2531 (See DXC R6 spec for port index convention). This MIB table is used only for LT-1 interface.
INT prtExHsrConnect	1.3.6.1.4.1.164.3.2.3.2.10.1.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtExHsrProtocol	1.3.6.1.4.1.164.3.2.3.2.10.1.1.5	INTEGER	read-write	This object indicates the protocol.
INT prtExHsrRate	1.3.6.1.4.1.164.3.2.3.2.10.1.1.6	INTEGER	read-write	This object indicates the port speed. The 16,32,48,56,64 and 128 kbps rates are applicable only for Sync protocol. The 57.6 and 115.2 kbps rates are applicable only for Async protocol. notConnected= 0 rate.
INT prtExHsrDataBits	1.3.6.1.4.1.164.3.2.3.2.10.1.1.7	INTEGER	read-write	Data Bits. This object is applicable for Async protocol only.
INT prtExHsrParity	1.3.6.1.4.1.164.3.2.3.2.10.1.1.8	INTEGER	read-write	- For HS-R card, this object indicates if the parity bit is needed or not. Therefore, the 'no' and 'yes; values are applicable. - For HS-S12, HS-U12, the parity type is selected: no, odd, even. This object is applicable for Async protocol only.
INT prtExHsrStopBits	1.3.6.1.4.1.164.3.2.3.2.10.1.1.9	INTEGER	read-write	This object indicates the minimum number of stop bits in the tx async frame. This object is applicable for Async protocol only.
INT prtExHsrCts	1.3.6.1.4.1.164.3.2.3.2.10.1.1.10	INTEGER	read-write	CTS. This object is applicable for Async protocol only.
INT prtExHsrClkMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.11	INTEGER	read-write	Clock mode. This object is applicable for Sync protocol only.
INT prtExHsrLinkTo	1.3.6.1.4.1.164.3.2.3.2.10.1.1.12	INTEGER	read-write	It indicates the slot of the main link card to which the HS-R card is mapped. notApplicable - for HS-U/1 internal ports. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExHsrDcdDsr	1.3.6.1.4.1.164.3.2.3.2.10.1.1.13	INTEGER	read-write	DCD & DSR.
INT prtExHsrOperMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.14	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request.
INT prtExHsrRtsDtr	1.3.6.1.4.1.164.3.2.3.2.10.1.1.15	INTEGER	read-write	RTS & DTR.
INT prtExHsrLlbEnable	1.3.6.1.4.1.164.3.2.3.2.10.1.1.16	INTEGER	read-write	Enable/Disable LLB.
INT prtExHsrRlbEnable	1.3.6.1.4.1.164.3.2.3.2.10.1.1.17	INTEGER	read-write	Enable/Disable RLB.
INT prtExHsrRateAdapt	1.3.6.1.4.1.164.3.2.3.2.10.1.1.18	INTEGER	read-write	Rate Adaptation - takes a low rate and adapts it to 64Kbps. This object specifies the means this adaptation is done by.
INT prtExHsrRemoteModem	1.3.6.1.4.1.164.3.2.3.2.10.1.1.19	INTEGER	read-write	Remote modem. asmi31s2 = ASMi-31/2
INT prtExHsrEncapsMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.20	INTEGER	read-write	Low Speed encapsulation method over PCM. When Encapsulation mode is Latency optimized, only rates up to 19.2 are supported. In this case a double number of bits occupy the Time Slot. For up to 9.6 Kbps - 4 bits are occupied. For 14.4 & 19.2 Kbps - 8 bits are occupied. When Encapsulation Mode is Bandwidth Optimized: For up to 9.6 Kbps - 2 bits are occupied. For 14.4 & 19.2 Kbps - 4 bits are occupied. For higher rates - 8 bits are occupied.
prtMbeCnfg	1.3.6.1.4.1.164.3.2.3.2.11
prtExMbeCnfgTable	1.3.6.1.4.1.164.3.2.3.2.11.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExMbeCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.11.1.1		not-accessible	An entry in table.
I32 prtExMbeCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExMbeSltIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtExMbePrtIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtExMbeLan	1.3.6.1.4.1.164.3.2.3.2.11.1.1.4	INTEGER	read-write	This attribute indicates whether the MBE port is operated as main or remote bridge.
prtInMbeCnfgTable	1.3.6.1.4.1.164.3.2.3.2.11.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInMbeCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.11.2.1		not-accessible	An entry in table.
I32 prtInMbeCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtInMbeSltIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtInMbePrtIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtInMbeConnect	1.3.6.1.4.1.164.3.2.3.2.11.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInMbeRate	1.3.6.1.4.1.164.3.2.3.2.11.2.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInMbeLinkTo	1.3.6.1.4.1.164.3.2.3.2.11.2.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
prtTreCnfg	1.3.6.1.4.1.164.3.2.3.2.12
prtExTreCnfgTable	1.3.6.1.4.1.164.3.2.3.2.12.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExTreCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.12.1.1		not-accessible	An entry in table.
I32 prtExTreCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExTreSltIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtExTrePrtIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtExTreLan	1.3.6.1.4.1.164.3.2.3.2.12.1.1.4	INTEGER	read-write	This attribute indicates whether the TRE port is operated as main or remote bridge. Default=remote.
INT prtExTreLanRate	1.3.6.1.4.1.164.3.2.3.2.12.1.1.5	INTEGER	read-write	This attribute indicates the Rate of the TRE port in Mbit/sec. Default-r4M.
prtInTreCnfgTable	1.3.6.1.4.1.164.3.2.3.2.12.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInTreCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.12.2.1		not-accessible	An entry in table.
I32 prtInTreCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtInTreSltIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtInTrePrtIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtInTreConnect	1.3.6.1.4.1.164.3.2.3.2.12.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInTreRate	1.3.6.1.4.1.164.3.2.3.2.12.2.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInTreLinkTo	1.3.6.1.4.1.164.3.2.3.2.12.2.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
prtLs6Cnfg	1.3.6.1.4.1.164.3.2.3.2.13
prtExLs6CnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExLs6CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.1.1		not-accessible	An entry in table.
I32 prtExLs6CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExLs6SltIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExLs6PrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.3	INTEGER	read-only	This attribute indicates a unique port index.
INT prtExLs6Connect	1.3.6.1.4.1.164.3.2.3.2.13.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs6Protocol	1.3.6.1.4.1.164.3.2.3.2.13.1.1.5	INTEGER	read-write	This attribute indicates the protocol. async - can be selected only for ports 1-2.
INT prtExLs6Rate	1.3.6.1.4.1.164.3.2.3.2.13.1.1.6	INTEGER	read-write	Port rates in bps. g1 - contains the values : (2)-(6),(9),(12),(16) g2 - contains the values : (7),(10),(14),(19) g3 - contains the values : (8),(11),(13),(15),(17),(18),(20); it is not applicable when using Async protocol. Rates of pair ports (1-2, 3-4, 5-6) must be from the same group.
INT prtExLs6ClkMode	1.3.6.1.4.1.164.3.2.3.2.13.1.1.7	INTEGER	read-write	This attribute indicates a unique port operation clock mode. It is applicable for Sync protocol only .
INT prtExLs6CtrlSignal	1.3.6.1.4.1.164.3.2.3.2.13.1.1.8	INTEGER	read-write	Control Signal.
INT prtExLs6DataBits	1.3.6.1.4.1.164.3.2.3.2.13.1.1.9	INTEGER	read-write	Data Bits. This object is applicable for Async protocol only.
INT prtExLs6Cts	1.3.6.1.4.1.164.3.2.3.2.13.1.1.10	INTEGER	read-write	This object indicates the CTS control line operation mode.
INT prtExLs6LinkToInternal	1.3.6.1.4.1.164.3.2.3.2.13.1.1.11	INTEGER	read-write	This object indicates which internal port of the card, the external port is linked to.
prtExLs6VCnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExLs6VCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.2.1		not-accessible	An entry in table.
I32 prtExLs6VCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExLs6VSltIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExLs6VPrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExLs6VConnect	1.3.6.1.4.1.164.3.2.3.2.13.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs6VRate	1.3.6.1.4.1.164.3.2.3.2.13.2.1.5	INTEGER	read-write	Rate (bps) used for FAX transmission and Voice coding.
INT prtExLs6VEchoCanceler	1.3.6.1.4.1.164.3.2.3.2.13.2.1.6	INTEGER	read-write	Echo canceler activation.
INT prtExLs6VIfType	1.3.6.1.4.1.164.3.2.3.2.13.2.1.7	INTEGER	read-write	This attribute indicates the interface type of the port. w4wire - is applicable only for E&M port type.
I32 prtExLs6VTxGain	1.3.6.1.4.1.164.3.2.3.2.13.2.1.8	Integer32	read-write	Transmit gain in dBm. E&M - values range: -17 .. 8 FXO - values range: -16 .. 4 FXS - values range: -13 .. 8
I32 prtExLs6VRxGain	1.3.6.1.4.1.164.3.2.3.2.13.2.1.9	Integer32	read-write	Receive gain in dBm. E&M - values range: -17 .. 2 FXO - values range: -17 .. -1 FXS - values range: -17 .. 2
INT prtExLs6VOos	1.3.6.1.4.1.164.3.2.3.2.13.2.1.10	INTEGER	read-write	Out of Service signaling mode.
prtInLs6CnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInLs6CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.3.1		not-accessible	An entry in table.
I32 prtInLs6CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtInLs6SltIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtInLs6PrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.3	INTEGER	read-only	This attribute indicates a unique internal port index.
INT prtInLs6Connect	1.3.6.1.4.1.164.3.2.3.2.13.3.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel.
INT prtInLs6TandemMode	1.3.6.1.4.1.164.3.2.3.2.13.3.1.5	INTEGER	read-write	This object indicates the Tandem Mode. tandemSlave - is valid only for an LS-6 card having on the (current slot-1) an LS-6 card with 'tandemMaster' mode.
INT prtInLs6Rate	1.3.6.1.4.1.164.3.2.3.2.13.3.1.6	INTEGER	read-write	Main Rate in Kbps.
INT prtInLs6RemoteType	1.3.6.1.4.1.164.3.2.3.2.13.3.1.7	INTEGER	read-write	Remote Type. notApplicable - when prtInLs6TandemMode=tandemSlave
INT prtInLs6LinkTo	1.3.6.1.4.1.164.3.2.3.2.13.3.1.8	INTEGER	read-write	It indicates the slot of the main link card to which the Ls6 card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - when prtInLs6TandemMode=tandemSlave. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
prtVc3Cnfg	1.3.6.1.4.1.164.3.2.3.2.14
prtExVc3CnfgTable	1.3.6.1.4.1.164.3.2.3.2.14.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExVc3CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.14.1.1		not-accessible	An entry in table.
I32 prtExVc3CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExVc3SltIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVc3PrtIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExVc3Connect	1.3.6.1.4.1.164.3.2.3.2.14.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
I32 prtExVc3TransGain	1.3.6.1.4.1.164.3.2.3.2.14.1.1.5	Integer32	read-write	Transmit gain in dBm.
I32 prtExVc3ReceiveGain	1.3.6.1.4.1.164.3.2.3.2.14.1.1.6	Integer32	read-write	Receive gain in dBm.
INT prtExVc3Wire	1.3.6.1.4.1.164.3.2.3.2.14.1.1.7	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
INT prtExVc3Rate	1.3.6.1.4.1.164.3.2.3.2.14.1.1.8	INTEGER	read-write	Rate in bps.
INT prtExVc3EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.14.1.1.9	INTEGER	read-write	Echo canceler activation. The value will be the same for all the card's external ports.
prtInVc3CnfgTable	1.3.6.1.4.1.164.3.2.3.2.14.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInVc3CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.14.2.1		not-accessible	An entry in table.
I32 prtInVc3CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtInVc3SltIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtInVc3PrtIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtInVc3Connect	1.3.6.1.4.1.164.3.2.3.2.14.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInVc3Rate	1.3.6.1.4.1.164.3.2.3.2.14.2.1.5	INTEGER	read-write	Rate in bps.
INT prtInVc3Oos	1.3.6.1.4.1.164.3.2.3.2.14.2.1.6	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
INT prtInVc3LinkTo	1.3.6.1.4.1.164.3.2.3.2.14.2.1.7	INTEGER	read-write	This attribute indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
prtVcPbxCnfg	1.3.6.1.4.1.164.3.2.3.2.15
prtExVcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExVcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.1.1		not-accessible	An entry in table.
I32 prtExVcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtExVcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExVcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.1.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtExVcPbxGroup	1.3.6.1.4.1.164.3.2.3.2.15.1.1.5	INTEGER	read-only	The group object links together several VC-PBX cards, concerning compression of the same input T1/E1 link time-slots. When ports of different slots have the same group, they are linked. When ports have a different group, they are not linked. For VC-PBX/T1 and E1 cards, this object is - their own IO Slot. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVcPbxTransparent	1.3.6.1.4.1.164.3.2.3.2.15.1.1.6	INTEGER	read-write	This object indicates whether the Transparent transfer of Time-Slots is required or not. Time-Slots transferred by Transparent, will not be compressed. no - applicable only for VC-PBX/T1 and VC-PBX/E1 cards yes - applicable only for VC-PBX/T1 and VC-PBX/E1 cards notApplicable - only for VC-PBX cards.
I32 prtExVcPbxTransSignalTs	1.3.6.1.4.1.164.3.2.3.2.15.1.1.7	Integer32	read-write	This object specifies the ML Time-Slot dedicated to the signaling of the PABX Transparent TSs. None = 255. When prtExVcPbxTransparent=no this object's value=None (255) When prtExVcPbxTransparent=notApplicable, this object's value=None (255). When prtExVcPbxTransparent=yes: - for VC-PBX/T1 ports, this object's valid values are 1..16 or None (255). - for VC-PBX/E1 ports, this object's value will be 16 or None (255).
INT prtExVcPbxFrame	1.3.6.1.4.1.164.3.2.3.2.15.1.1.8	INTEGER	read-write	This object is the frame parameter for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 values for the VC-PBX/T1 card. E1 values for the VC-PBX/E1 card. notApplicable - for the VC-PBX card. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7)
INT prtExVcPbxRestoreTime	1.3.6.1.4.1.164.3.2.3.2.15.1.1.9	INTEGER	read-write	The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface. ccittE1 - is applicable only for VC-PBX/E1 card notApplicable - is applicable for VC-PBX card
INT prtExVcPbxLineCode	1.3.6.1.4.1.164.3.2.3.2.15.1.1.10	INTEGER	read-write	This object is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for VC-PBX/T1 E1 line code parameters for VC-PBX/E1 notApplicable - for VC-PBX This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExVcPbxLineLength	1.3.6.1.4.1.164.3.2.3.2.15.1.1.11	INTEGER	read-write	This object is the line length parameter. It is applicable only for the VC-PBX/T1 card. notApplicable - for the VC-PBX and VC-PBX/E1 card. lenXXXpXXXft = len-XXX-XXXft.
INT prtExVcPbxLinkTo	1.3.6.1.4.1.164.3.2.3.2.15.1.1.12	INTEGER	read-write	This object indicates the slot of the ML card to which the VC-PBX/T1, VC-PBX/E1 card Transparent TSs are mapped. notApplicable - for VC-PBX card AND for VC-PBX/T1, VC-PBX/E1 cards, when prtExVcPbxTransparent=no . In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExVcPbxSignalOper	1.3.6.1.4.1.164.3.2.3.2.15.1.1.13	INTEGER	read-write	This object indicates the Signaling Operation of the VC-PBX/T1, VC-PBX/E1 external port. notApplicable - for VC-PBX card normal - all 4 signaling bits are transferred. bEqA - copy the A bit into the B bit. Applicable only for VC-PBX/T1.
INT prtExVcPbxIdleCode	1.3.6.1.4.1.164.3.2.3.2.15.1.1.14	INTEGER	read-write	Determines the code for transmission in empty time slots. notApplicable - for VC-PBX card .
prtIn1p6VcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtIn1p6VcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.2.1		not-accessible	An entry in table.
I32 prtIn1p6VcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtIn1p6VcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtIn1p6VcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtIn1p6VcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.2.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtIn1p6VcPbxRate	1.3.6.1.4.1.164.3.2.3.2.15.2.1.5	INTEGER	read-write	This object indicates the port Rate. For Normal mode (prtIn7p8VcPbxMode=normal), only part of the values are valid (constant rate). For Server mode (prtIn7p8VcPbxMode=server), all values are applicable (user can select the desired compression rate).
INT prtIn1p6VcPbxEchoCanceler	1.3.6.1.4.1.164.3.2.3.2.15.2.1.6	INTEGER	read-write	Echo canceler activation.
I32 prtIn1p6VcPbxPabxTs	1.3.6.1.4.1.164.3.2.3.2.15.2.1.7	Integer32	read-only	This object defines the PABX Time-Slot assigned to this internal port. For a T1 link, the valid values are: 1 .. 24. For an E1 link, the valid values are: 1 .. 31. This object is NOT applicable when prtIn1p6VcPbxConnect=no. This object is applicable for all cards of VC-PBX family. Default=the internal port index (1..6).
prtIn7p8VcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtIn7p8VcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.3.1		not-accessible	An entry in table.
I32 prtIn7p8VcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
INT prtIn7p8VcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtIn7p8VcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtIn7p8VcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.3.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtIn7p8VcPbxMode	1.3.6.1.4.1.164.3.2.3.2.15.3.1.5	INTEGER	read-write	This object indicates the working mode of the port: - normal - the compressed voice will be sent to an MTML card inside the Mux. - server - the compressed voice will be sent to the Digital Voice connector, as a service to an outside user.
INT prtIn7p8VcPbxRate	1.3.6.1.4.1.164.3.2.3.2.15.3.1.6	INTEGER	read-write	This object indicates the port Main Rate. For Server mode (prtIn7p8VcPbxMode=server), the value will be notApplicable.
INT prtIn7p8VcPbxSignalMode	1.3.6.1.4.1.164.3.2.3.2.15.3.1.7	INTEGER	read-write	This object indicates the Signal Mode. For Server mode (prtIn7p8VcPbxMode=server), the only valid values are: - none - aBit
INT prtIn7p8VcPbxOos	1.3.6.1.4.1.164.3.2.3.2.15.3.1.8	INTEGER	read-write	Out of service Signaling mode.
INT prtIn7p8VcPbxLinkTo	1.3.6.1.4.1.164.3.2.3.2.15.3.1.9	INTEGER	read-write	This object indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For Server mode (prtIn7p8VcPbxMode=server), this object is not applicable. Both ports, 7 and 8 should be linked to the same Slot. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
prtExVcPbxTsTable	1.3.6.1.4.1.164.3.2.3.2.15.4		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtExVcPbxTsEntry	1.3.6.1.4.1.164.3.2.3.2.15.4.1		not-accessible	An entry in table.
I32 prtExVcPbxTsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtExVcPbxTsSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtExVcPbxTsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.3	INTEGER	read-only	This attribute indicates a unique port number. VCPBX/E1, VCPBX/T1, VFPBX/E1, VFPBX/T1, VF-24/T1 and VF-30 cards have only one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. VFS cards have also internal ports.
I32 prtExVcPbxTsIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.4	Integer32	read-only	This attribute indicates a unique PABX time slot position. The valid time slots are 1..24 for T1 cards and 1..31 for E1 cards.
INT prtExVcPbxTsMode	1.3.6.1.4.1.164.3.2.3.2.15.4.1.5	INTEGER	read-write	This attribute indicates the usage, process and way of the specific PABX TS towards its destination: unused - the TS is not used (no processing, no destination). compressed - the TS is used, sent for compression to an internal port (for VF-PBX cards: 1..6 for of either the same card or a VF-PBX card of the same group). For VF-24/30/48/60 - 'compressed' represents 'compressed Voice' (to differentiate it from 'compressedCcs'). In this case, the TS is compressed by an internal port (1..8). transparent - the TS is used; no processing. It is sent directly for Bypass to a ML card the VF port/TS is linked to. compressedCcs - supported only by VF-24/30/48/60 cards. The TS is used; sent for compression to the CPU. mng - the TS is used for Management (this option is used when the external port is connected to another product that has to be managed via this dedicated TS. ccs1..ccs8 - supported only by VF-24/30/48/60 cards. Compressed TS that comes from a bundle of V5.1 or V5.2 PBX. ss7n1..ss7n8 - supported only by VF-24/30/48/60 cards. Compressed TS that comes from a bundle of V5.1 or V5.2 PBX. ss7n1 can work versus Vmux having prtExPh1MlTsType=ss7(6).
INT prtExVcPbxTsIConSlot	1.3.6.1.4.1.164.3.2.3.2.15.4.1.6	INTEGER	read-write	For VF-PBX cards, the io1..io12 values are applicable only when prtExVcPbxTsMode=compressed. Otherwise, its value should be noConnect. For VF-24/30/48/60 cards: - when prtExVcPbxTsMode=transparent or voiceTransparent, the io1..io12 values are applicable, indicating the ML Slot this TS is connected to. - when prtExVcPbxTsMode=compressed or compressedCcs, the value will be the same as prtExVcPbxTsSltIdx, since the compression is done within the same card. - for rest of the prtExVcPbxTsMode values, the value will be: noConnect. This object indicates whether the specified compressed/transparent time slot is connected/routed internally in the Agent and to which card it is connected. For VF-PBX card, the valid selectable slots are either the current one, (prtExVcPbxTsSltIdx), or a slot containing a VF-PBX card. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVcPbxTsIConPrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.7	INTEGER	read-write	This attribute indicates the port to which this TS is connected. For VF-PBX cards, only inPrt1..inPrt6 ports are valid. For VF-24/30/48/60 cards: - for prtExVcPbxTsMode=transparent or voiceTransparent, the valid ports are ML ports (exPrt1.. exPrt8, inPrt1.. inPrt8) - for prtExVcPbxTsMode=compressed or compressedCcs, the valid ports are internal ports of the same card (inPrt1..inPrt8) noConnect - when prtExVcPbxTsIConSlot=noConnect.
I32 prtExVcPbxTsIConTs	1.3.6.1.4.1.164.3.2.3.2.15.4.1.8	Integer32	read-write	This attribute indicates the ML TS to which this TS is connected. This object is not applicable for VF-PBX cards. For VF-24/30/48/60 cards it is applicable only when prtExVcPbxTsMode=transparent or voiceTransparent. The valid time slots are 1..24 for ML T1 cards and 1..31 for ML E1 cards. notApplicable - 255.
INT prtExVcPbxTsRemPrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.9	INTEGER	read-write	This attribute indicates the end-point port on the Remote unit. VF-24/T1 and VF-30/E1 cards have one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. noConnect - when prtExVcPbxTsMode=unused, transparent, voiceTransparent or mng.
I32 prtExVcPbxTsRemTs	1.3.6.1.4.1.164.3.2.3.2.15.4.1.10	Integer32	read-write	This attribute indicates the end-point TS on the Remote unit. The valid time slots are 1..24 for T1 ports and 1..31 for E1 ports. notApplicable - 255.
U32 prtExVcPbxTsRemConnID	1.3.6.1.4.1.164.3.2.3.2.15.4.1.11	Unsigned32	read-write	This attribute indicates the Connection ID with the Remote unit. notApplicable = 0.
INT prtExVcPbxTsSourceSlot	1.3.6.1.4.1.164.3.2.3.2.15.4.1.12	INTEGER	read-write	For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Slot of the Analog Voice port we want to compress. io1..io12 values are applicable only when prtExVcPbxTsMode=compressed(voice). Otherwise, its value should be noConnect. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
U32 prtExVcPbxTsSourcePrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.13	Unsigned32	read-write	For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Port within the Slot of the Analog Voice Card, we want to compress. exPrt1 - exPrt16 = 1 - 16 noConnect=100 - when prtExVcPbxTsCvServiceSlot=noConnect.
prtIsdnCnfg	1.3.6.1.4.1.164.3.2.3.2.16
prtIsdnCnfgTable	1.3.6.1.4.1.164.3.2.3.2.16.1		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtIsdnCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.16.1.1		not-accessible	An entry in table.
I32 prtIsdnCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtIsdnSltIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
I32 prtIsdnPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.3	Integer32	read-only	This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch
INT prtIsdnConnect	1.3.6.1.4.1.164.3.2.3.2.16.1.1.4	INTEGER	read-write	This attribute indicates if the port is connected.
INT prtIsdnSignalingProtocol	1.3.6.1.4.1.164.3.2.3.2.16.1.1.5	INTEGER	read-write	This attribute fixes which signaling protocol is used at this port (D-Channel). It is equivalent to isdnSignalingProtocol in the isdn MIB.
INT prtIsdnBasicRateLineTopology	1.3.6.1.4.1.164.3.2.3.2.16.1.1.6	INTEGER	read-write	This attribute is relevant for ISDN BRI only. It is equivalent to isdnBasicRateLineTopology in the isdn MIB.
INT prtIsdnMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.7	INTEGER	read-write	This attribute allows the user to configure the port as leased(2) in case of connection to a TDM network.
INT prtIsdnFilter	1.3.6.1.4.1.164.3.2.3.2.16.1.1.8	INTEGER	read-write	This attribute allows the user to configure the port: answerAll(2): accept all incoming calls, rejectAll(3): reject all incoming calls, selective(4): accept or reject according directory table. callBack (5): In this mode the ISDN Ch will reject incoming calls and will initiate call back to the rejected phone number.
INT prtIsdnSimultaneousCall	1.3.6.1.4.1.164.3.2.3.2.16.1.1.9	INTEGER	read-write	In case of simultaneous call (local,remote and remote,local): accept(2): accept the incoming call, reject(3): reject the incoming call.
I32 prtIsdnNumOfAbstractTerm	1.3.6.1.4.1.164.3.2.3.2.16.1.1.10	Integer32	read-write	An object for KM2100/4 agents. 255=Not Applicable When ISDN Standard = ETSI or NTT (European) the value should be 255 (NotApplicable) else If ML speed is 64Kbps value should be 1. If ML speed is 128Kbps value can be either 1 or 2 (user selection).
INT prtIsdnSwitchMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.11	INTEGER	read-write	For KM2100. auto - The call is initiated automatically by one of the IO cards connected to KML.10(ISDN card) having ISDN Switch Mode. manual - The call is initiated by the user manually, for KML.10 having ISDN Switch Mode (via mdlSCmd). connect- The call is initiated 'immediately', for KML.10 having ISDN Switch Mode. 'immediately'- means: immediately after power-up (when product performed Reset) OR, since this value appears in the active configuration. In this case, the call can be disconnected only by power-off of the product or by changing this object to another value (or actual Remove of the KML.10 relevant card). notApplicable - For other card types.
INT prtIsdnAbSide	1.3.6.1.4.1.164.3.2.3.2.16.1.1.12	INTEGER	read-write	This parameter indicates the QSIG side in layer 3. This definition is from the QSIG Standard.
INT prtIsdnQsigRole	1.3.6.1.4.1.164.3.2.3.2.16.1.1.13	INTEGER	read-write	This parameter indicates the QSIG side in layer 1 & 2.
INT prtIsdnInterface	1.3.6.1.4.1.164.3.2.3.2.16.1.1.14	INTEGER	read-write	It indicates the interface type: lt = line termination nt = network termination te = terminal equipment.
INT prtIsdnCallMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.15	INTEGER	read-write	This object indicates the acceptance of incoming calls. Initiate - Callout Listen - Callin.
I32 prtIsdnCallBackTimeout	1.3.6.1.4.1.164.3.2.3.2.16.1.1.16	Integer32	read-write	This object is applicable only if 'prtIsdnFilter' is 'CallBack' and determines how long to wait from receiving the incoming call until initiating the call back call. The vaules range should be '1..20 sec' and the default 10 sec.
prtIsdnEndpointTable	1.3.6.1.4.1.164.3.2.3.2.16.2		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtIsdnEndpointEntry	1.3.6.1.4.1.164.3.2.3.2.16.2.1		not-accessible	An entry in table.
I32 prtIsdnEndpointCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtIsdnEndpointSltIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
I32 prtIsdnEndpointPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.3	Integer32	read-only	This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch
INT prtIsdnEndpointIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.4	INTEGER	read-only	Since more than one endpoint may be defined per isdn entity, this field is a simple index. It corresponds to isdnEndpointIdx in the isdn MIB.
INT prtIsdnEndpointTeiType	1.3.6.1.4.1.164.3.2.3.2.16.2.1.5	INTEGER	read-create	The type of TEI (Terminal Endpoint Identifier) used for this Terminal Endpoint. In case of dynamic(1), the TEI value is selected by the switch. In case of static(2), a valid TEI value has to be entered in the isdnEndpointTeiValue object. interface type as well as the Terminal Endpoint type. static(2). On Basic Rate interfaces the default value is dynamic(1) for isdn(63) Terminal Endpoints. It corresponds to isdnEndpointTeiType in the isdn MIB.
I32 prtIsdnEndpointTeiValue	1.3.6.1.4.1.164.3.2.3.2.16.2.1.6	Integer32	read-create	When the TEI Type is static, the value of the TEI should be between 0 and 63. Else, it is not selectable by user. 255 = notApplicable. It corresponds to isdnEndpointTeiValue in the isdn MIB
STR prtIsdnEndpointSpid	1.3.6.1.4.1.164.3.2.3.2.16.2.1.7	DisplayString	read-create	The Service profile IDentifier (SPID) information for this Terminal Endpoint. It is is composed of 9-20 numeric characters. It corresponds to isdnEndpointSpid in the isdn MIB.
INT prtIsdnEndpointBearerCh	1.3.6.1.4.1.164.3.2.3.2.16.2.1.8	INTEGER	read-create	This is the selected dialing channel. anyChannel - the system selects the dialing channel.
ROW prtIsdnEndpointRowStatus	1.3.6.1.4.1.164.3.2.3.2.16.2.1.9	RowStatus	read-create	This field indicates whether to consider this endpoint or not. The only possible supported RowStatus vaules are active (1) and destroy (6).
prtIsdnDirectoryTable	1.3.6.1.4.1.164.3.2.3.2.16.3		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtIsdnDirectoryEntry	1.3.6.1.4.1.164.3.2.3.2.16.3.1		not-accessible	An entry in table.
I32 prtIsdnDirectoryCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtIsdnDirectorySltIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For MX300/30 ports: io1(5) = isdn1(5) and io2(6) = isdn2(6). In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
I32 prtIsdnDirectoryPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.3	Integer32	read-only	For MAXcess this is the internal port number: 101, 102,.... For KM-2100 the port index is calculated as follows: 100*Slot+Ch
STR prtIsdnDirectoryLocalAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.4	DisplayString	read-create	This is the local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryLocalSubAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.5	DisplayString	read-create	This is the local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
STR prtIsdnDirectoryRemoteAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.6	DisplayString	read-create	This is the remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryRemoteSubAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.7	DisplayString	read-create	This is the remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
I32 prtIsdnDirectoryPrtNu	1.3.6.1.4.1.164.3.2.3.2.16.3.1.8	Integer32	read-create	This is the external port number connected to this entry.
I32 prtIsdnDirectoryTeiId	1.3.6.1.4.1.164.3.2.3.2.16.3.1.9	Integer32	read-create	This is the abstract terminal id if relevant, connected to this entry.
ROW prtIsdnDirectoryRowStatus	1.3.6.1.4.1.164.3.2.3.2.16.3.1.10	RowStatus	read-create	This is the status for the row. It allows to know whether to consider this row or not. The only possible supported RowStatus vaules are active (1) and destroy (6).
STR prtIsdnDirectoryLocalAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.11	DisplayString	read-create	This is the second local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryLocalSubAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.12	DisplayString	read-create	This is the second local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
STR prtIsdnDirectoryRemoteAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.13	DisplayString	read-create	This is the second remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank(20 characters)
STR prtIsdnDirectoryRemoteSubAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.14	DisplayString	read-create	This is the second remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
prtLogicalCnfg	1.3.6.1.4.1.164.3.2.3.2.17
prtLogicalCnfgTable	1.3.6.1.4.1.164.3.2.3.2.17.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtLogicalCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.17.1.1		not-accessible	An entry in table.
I32 prtLogicalCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtLogicalSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.2	INTEGER	read-only	Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
I32 prtLogicalPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be an internal port number: inPrt1(101)->inPrt50(150), linkSel1(200)->linkSel50(250), encaps1(300)-> encaps50(350), huntGr1(101) -> huntGr10(110).
INT prtLogicalConnect	1.3.6.1.4.1.164.3.2.3.2.17.1.1.4	INTEGER	read-create	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtLogicalFunction	1.3.6.1.4.1.164.3.2.3.2.17.1.1.5	INTEGER	read-create	This parameter defines the function of the relevant channel.
ROW prtLogicalRowStatus	1.3.6.1.4.1.164.3.2.3.2.17.1.1.6	RowStatus	read-create	This parameter allows the NMS to create/delete logical ports. The only possible supported RowStatus vaules are active (1) and destroy (6).
linkSelectorCnfgTable	1.3.6.1.4.1.164.3.2.3.2.17.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
linkSelectorCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.17.2.1		not-accessible	An entry in table.
I32 linkSelectorCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT linkSelectorSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.2	INTEGER	read-only	Slot Index
I32 linkSelectorPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be internal port number: higher or equal to linkSeL1(201).
I32 linkSelectorMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.17.2.1.4	Integer32	read-write	Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=move immediately to higher prioritized connected link. UNIT is seconds.
INT linkSelectorMode	1.3.6.1.4.1.164.3.2.3.2.17.2.1.5	INTEGER	read-write	If the link selector is in mode: backup(2)=then the link with the lower priority will be used in case of failure of the higher priority link, bod(3)=bandwidth on demand or dynamic bandwidth allocation means that links with lower priority will be used whenever additional bandwidth is required.
INT linkSelectorRevert	1.3.6.1.4.1.164.3.2.3.2.17.2.1.6	INTEGER	read-write	If the link selector is in mode backup: auto(2)=return automatically to Main link when it is OK. manual(3)=stays connected to backup link.
I32 linkSelectorMinBUSession	1.3.6.1.4.1.164.3.2.3.2.17.2.1.7	Integer32	read-write	Minimum duration of a backup session before returning to Main Link. Relevant in Backup Mode and when Revert is auto(2). Value 255 is for NEVER which means never return to Main Link. UNIT is minutes.
linkSelectorPLinkTable	1.3.6.1.4.1.164.3.2.3.2.17.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
linkSelectorPLinkEntry	1.3.6.1.4.1.164.3.2.3.2.17.3.1		not-accessible	An entry in table.
I32 pLinkCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT pLinkSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.2	INTEGER	read-only	Slot Index
I32 pLinkPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be the link selector number.
I32 pLinkIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.4	Integer32	read-only	This index is the row number.
INT pLinkSlotNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.5	INTEGER	read-write	The slot of the prioritized link. For ISDN BRI ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
I32 pLinkPortNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.6	Integer32	read-write	The port of the prioritized link. Value 100 is for noConnect.
I32 pLinkPrioNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.7	Integer32	read-write	The priority of the prioritized link. MIN=1...., MAX=8.
INT pLinkVRate	1.3.6.1.4.1.164.3.2.3.2.17.3.1.8	INTEGER	read-write	The rate to use with this link.
prtFrPlusCnfg	1.3.6.1.4.1.164.3.2.3.2.18
prtFrPlusCnfgTable	1.3.6.1.4.1.164.3.2.3.2.18.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtFrPlusCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.18.1.1		not-accessible	An entry in table.
I32 prtFrPlusCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
INT prtFrPlusSltIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.2	INTEGER	read-only	Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
I32 prtFrPlusPrtIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be: - for ISDN cards: inPrt1(101)->inPrt50(150) - for MHS1 card : exPrt1(1) - for MHS3, MLS3 cards: exPrt1(1)->exPrt3(3) - for MLS6 cards: exPrt1(1)->exPrt6(6).
OCT prtFrPlusNotSegmentedPriorities	1.3.6.1.4.1.164.3.2.3.2.18.1.1.4	OCTET STRING	read-write	This parameter is relevant only for FR+ protocol and asks the MXcess NOT to segment data with specified priorities: from LSB: bit 1 is for priority 1, bit 2 is for priority 2, .... till bit 7 for priority 7. - a priority selected to be segmented : its bit will be '0' - a priority not to be segmented : its bit will be '1' Default is 00000000; i.e, segment all priorities.
prtMl4Cnfg	1.3.6.1.4.1.164.3.2.3.2.19
prtMl4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.19.1		not-accessible	This is an extension table for MTML-4 card parameters.
prtMl4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.19.1.1		not-accessible	An entry in table.
I32 prtMl4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
INT prtMl4SltIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
INT prtMl4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtMl4SigProfile	1.3.6.1.4.1.164.3.2.3.2.19.1.1.4	INTEGER	read-write	This object indicates the Signaling Profile of the port. none - when the Frame is G732N (no MF) or Unframed. p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5 perTS = when Signaling Profile is selected per TS.
INT prtMl4CGA	1.3.6.1.4.1.164.3.2.3.2.19.1.1.5	INTEGER	read-write	This object selects the method used to signal the CGA state to the other end, through the main link. 'none' - non-transparent mode. When one of the links (main) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos' will be transmitted to the other end. 'trans' - when one of the links (main) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos' will be transmitted to the other end.
INT prtMl4Oos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.6	INTEGER	read-write	'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0
OCT prtMl4VoiceOos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.7	OCTET STRING	read-write	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT prtMl4DataOos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.8	OCTET STRING	read-write	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
INT prtMl4Service	1.3.6.1.4.1.164.3.2.3.2.19.1.1.9	INTEGER	read-write	Link Service. leasedLine - usual TDM interface. v51 - V5.1 interface. v52Master - V5.2 Link to Local Exchange. v52Slave - a ML that is transferred to the v52Master.
IP prtMl4IpAddress	1.3.6.1.4.1.164.3.2.3.2.19.1.1.10	IpAddress	read-write	IP Address of the port.
IP prtMl4IpMask	1.3.6.1.4.1.164.3.2.3.2.19.1.1.11	IpAddress	read-write	IP subnet mask of the port.
INT prtMl4SignalingMode	1.3.6.1.4.1.164.3.2.3.2.19.1.1.12	INTEGER	read-write	Refers to the signaling mode of the port (or framer module). notApplicable(1)- means that no framer is needed for this port (no signaling), or that this object is not relevant. cas(2) means Channel Associated Signaling. Used for E1 Links. ccs(3) is the Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). robbedBit(4) is a method implementing 7 bits for the voice and 1 bit dedicated for signaling. Used for T1 Links. other (5)- Signaling generally exists though not specifically according to one of the values listed ; this port uses a framer in this case.
INT prtMl4EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.19.1.1.13	INTEGER	read-write	Echo canceler activation.
INT prtMl4OosErrorSource	1.3.6.1.4.1.164.3.2.3.2.19.1.1.14	INTEGER	read-write	OOS (Out-of-Service) Error Source. This object is applicable for T1 ports only.
I32 prtMl4OosEntryThreshold	1.3.6.1.4.1.164.3.2.3.2.19.1.1.15	Integer32	read-write	This object defines the number of Errors per Second that determine the minimum unacceptable noise level. This value will be the Entry Threshold to the OOS (Out-of-Service) state. This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable.
I32 prtMl4OosExitThreshold	1.3.6.1.4.1.164.3.2.3.2.19.1.1.16	Integer32	read-write	This object defines the number of consecutive Error-Free-Seconds before going from OOS state to Normal state. This value will be the Exit Threshold from the OOS (Out-of-Service) state. Units=seconds This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable.
I32 prtMl4LogicalLinkId	1.3.6.1.4.1.164.3.2.3.2.19.1.1.17	Integer32	read-write	This object defines for a V5.2 Master ML the Logical Link Id. Valid values are: 0..256. NA=257.
I32 prtMl4DedicatedTs	1.3.6.1.4.1.164.3.2.3.2.19.1.1.18	Integer32	read-write	A unique number to identify Dedicated TS of the E1 port (V5.2). It is applicable only when prtMl4Service=v52Slave and prtExPh1MlInbandMng selected is dedicatedTs, dedicatedPpp or dedicatedFr. 1..31 - Dedicated TS of E1 255 - notApplicable Other values are invalid.
INT prtMl4RemCrc	1.3.6.1.4.1.164.3.2.3.2.19.1.1.19	INTEGER	read-write	This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.
INT prtMl4CrossConnectLevel	1.3.6.1.4.1.164.3.2.3.2.19.1.1.20	INTEGER	read-write	This object indicates whether the cross connect is on DS1 or DS0 (time-slots) level. When cross connect level is ds1, Destination Slot is indicated by prtGenCnfgLinkToSlot, Destination Port is indicated by prtGenCnfgLinkToPort. For Unframed Line Type, cross connect level can be either notApplicable (NC=not connected) or DS1. Otherwise, default value is ds0.
INT prtMl4PppEchoFailDetection	1.3.6.1.4.1.164.3.2.3.2.19.1.1.21	INTEGER	read-write	This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Disable. Enable - will be selected mainly when a T1/E1 Ring exists and between 2 adjacent Ring devices there is another device or Net, that causes these Ring devices not to sense that the PPP connection between them is lost. In this case, Echo Request should be initiated by the port.
prtAcmCnfg	1.3.6.1.4.1.164.3.2.3.2.20
prtAcmCnfgTable	1.3.6.1.4.1.164.3.2.3.2.20.1		not-accessible	This is a table for ACM port parameters.
prtAcmCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.20.1.1		not-accessible	An entry in table.
I32 prtAcmCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
INT prtAcmSltIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
INT prtAcmPrtIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtAcmConnect	1.3.6.1.4.1.164.3.2.3.2.20.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.
INT prtAcmActiveState	1.3.6.1.4.1.164.3.2.3.2.20.1.1.5	INTEGER	read-write	This attribute indicates the Electric Active State of the port.
STR prtAcmAlrString	1.3.6.1.4.1.164.3.2.3.2.20.1.1.6	DisplayString	read-write	Alarm string selected by user for the Inbound ports. This object is applicable only for the Inbound Ports: ext-5..ext-12. For the Outbound Ports (ext-1..ext-4), the size of this string will be 0.
prtE2Cnfg	1.3.6.1.4.1.164.3.2.3.2.21
prtE2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.21.1		not-accessible	This is a table for E2 port parameters.
prtE2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.21.1.1		not-accessible	An entry in table.
I32 prtE2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
INT prtE2SltIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
INT prtE2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtE2Connect	1.3.6.1.4.1.164.3.2.3.2.21.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.
INT prtE2MngOnNationalBit	1.3.6.1.4.1.164.3.2.3.2.21.1.1.5	INTEGER	read-write	This attribute indicates whether National Bit will be used for Management or not.
prtLanWanCnfg	1.3.6.1.4.1.164.3.2.3.2.22
prtLanWanCnfgTable	1.3.6.1.4.1.164.3.2.3.2.22.1		not-accessible	This is a table for Lan-Wan port parameters.
prtLanWanCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.22.1.1		not-accessible	An entry in table.
I32 prtLanWanCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
INT prtLanWanSltIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.2	INTEGER	not-accessible	This object indicates a unique slot position where the module is inserted.
I32 prtLanWanPrtIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.3	Integer32	not-accessible	This object indicates a unique number to identify a port in a specific card. Generally, for MP-210X/2200, the Port Index will be according to the external/internal port number: - exPrtX : X - inPrtX : 100 + X For FCD-155, refer to device specification
INT prtLanWanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.4	INTEGER	read-write	This object determines the working mode of this port. For FCD155, layer3SubnetSwitch is not applicable
I32 prtLanWanDestIf	1.3.6.1.4.1.164.3.2.3.2.22.1.1.5	Integer32	read-write	This object determines the Destination Interface for the frames received by this port. - Switching Table = 100 (it means that the destination interface will be determined by the Switching Table) - inPrtX (internal-X port): 100 + X . For FCD-155 this object is not applicable =0
INT prtLanWanEgressVlanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.6	INTEGER	read-write	This object determines what to do with the VLAN frames that exit via the WAN side of the port. This object is not applicable when prtLanWanMode=l3SubnetSwitch(4).
INT prtLanWanL2Protocol	1.3.6.1.4.1.164.3.2.3.2.22.1.1.7	INTEGER	read-write	L2 Protocol. When prtLanWanMode=l3SubnetSwitch(4), the only valid value is ppp(3).
I32 prtLanWanStpPriority	1.3.6.1.4.1.164.3.2.3.2.22.1.1.8	Integer32	read-write	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID.
I32 prtLanWanStpCost	1.3.6.1.4.1.164.3.2.3.2.22.1.1.9	Integer32	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT prtLanWanToLanVlanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.10	INTEGER	read-write	This object determines what to do with the VLAN frames that come from WAN side of the port and exit towards one of the LAN ports. This object is applicable only when prtLanWanDestIf=100 or 101 (Switching Table or inPrt1).
I32 prtLanWanVlanId	1.3.6.1.4.1.164.3.2.3.2.22.1.1.11	Integer32	read-write	This is the VLAN Id attached to a frame, when the relevant Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is tag or doubleTag. 0=not applicable.
I32 prtLanWanVlanPriority	1.3.6.1.4.1.164.3.2.3.2.22.1.1.12	Integer32	read-write	This is the VLAN Priority attached to a frame, when the relevant Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is tag or doubleTag. Valid values: 0..7 255=not applicable.
I32 prtLanWanMtu	1.3.6.1.4.1.164.3.2.3.2.22.1.1.13	Integer32	read-write	The size of the largest packet which can be sent/received on the interface, specified in octets. Valid values change per device. 0=not applicable.
INT prtLanWanVlanType	1.3.6.1.4.1.164.3.2.3.2.22.1.1.14	INTEGER	read-write	This oject indicates type of VLAN this port is assigned to. Port Base Vlan parameters are defined by objects under radBridgePortBaseVlan
dacsMux	1.3.6.1.4.1.164.3.3
dacsMuxEvents	1.3.6.1.4.1.164.3.3.0			The events for DACS MUX.
NTF sanityCheckTrap	1.3.6.1.4.1.164.3.3.0.1			This trap is sent after a data base download attempt. It returns the sanity result status and the configuration no.checked.
NTF dacsMuxAlarmsTrap	1.3.6.1.4.1.164.3.3.0.2			This trap is sent when an alarm occurs.
NTF mdlConnectTrap	1.3.6.1.4.1.164.3.3.0.3			This trap is sent when a card is removed.
NTF sysAlrStatusTrap	1.3.6.1.4.1.164.3.3.0.4			This trap is sent upon any change in the value of any of the variables.
NTF sysStatusChangedTrap	1.3.6.1.4.1.164.3.3.0.5			This trap is sent when Leds status is changed.
NTF cnfgUpdateTrap	1.3.6.1.4.1.164.3.3.0.6			This trap is sent upon change of the active Configuration DB.
NTF sysRedundancyStatusTrap	1.3.6.1.4.1.164.3.3.0.7			The trap is sent upon change in Redundancy Status.
NTF sysRedundancyActiveCardTrap	1.3.6.1.4.1.164.3.3.0.8			The trap is sent upon change of Active Main/CL Card.
NTF sysRedundancyActivePortTrap	1.3.6.1.4.1.164.3.3.0.9			The trap is sent upon change of Active Port of Redundancy Group.
systemDacsMux	1.3.6.1.4.1.164.3.3.1
sysSa	1.3.6.1.4.1.164.3.3.1.1
I32 sysSaSwchStatus	1.3.6.1.4.1.164.3.3.1.1.1	Integer32	read-only	This object indicates the status of the switches on the SA unit. Each switch is represented by a bit. The status is a sum of 2n, according to the bits. For SMODs products see modem's specification. For DXC product see the following: There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (21 + 2**0). When the status of the switches is unknown, the value of this object will be 255.
STR sysSaSwRevision	1.3.6.1.4.1.164.3.3.1.1.2	DisplayString	read-only	This object indicates the Software revision of the system.
STR sysSaHwVersion	1.3.6.1.4.1.164.3.3.1.1.3	DisplayString	read-only	This object indicates the Hardware version of the system.
I32 sysSaPorts	1.3.6.1.4.1.164.3.3.1.1.4	Integer32	read-only	This object indicates the ports that are present in the system. Each possible port is represented by a bit. The value of this object is a sum of 2**n, n=number of bits. '1' - means that the port exists '0' - means that the port does not exist For detailed bit assignment, see product's spec. Bit 0 = LSB When this object is not relevant, the value will be 0. In some cases, this object may represent ports configuration of the system AND its far-end unit.
I32 sysSaReadSwch	1.3.6.1.4.1.164.3.3.1.1.5	Integer32	read-write	This object indicates wether the configuration will be read from the DIP switches on the SA (stand alone) unit. Each switch is represented by a bit. If the bit is 1: the configuration will be read from the HW switch position. If the bit is 0: the configuration will be read from the SW user configuration. The DIP switches are different in each of the RAD devices. In the Tiny Router (starting from the LSB) the following switches exist: Bit 0: WAN Loop Bit 1: LAN Full Duplex (When LAN AUI connector, it is SQE) Bit 2: PPP (When WAN 4 Wire connector, it is LONG) Bit 3: IP Learn
INT sysSaBuActivePort	1.3.6.1.4.1.164.3.3.1.1.6	INTEGER	read-only	This object shows through which port the traffic is flowing (the current Active Port) when the Backup mechanism exists. When No Backup exists in the device, the value should be: notApplicable(1).
sysHub	1.3.6.1.4.1.164.3.3.1.2
sysChas	1.3.6.1.4.1.164.3.3.1.2.1
I32 chassTotalNoOfSlt	1.3.6.1.4.1.164.3.3.1.2.1.1	Integer32	read-only	This object indicates the number of physical slots in the Hub chassis.
I32 chassTotalNoOfIoSlt	1.3.6.1.4.1.164.3.3.1.2.1.2	Integer32	read-only	This object indicates the total number of physical IO slots in the chassis, (not all slots must be occupied and active).
I32 chassTotalNoOfPsSlt	1.3.6.1.4.1.164.3.3.1.2.1.3	Integer32	read-only	This object indicates the number of physical Power Supply slots in the chassis.
I32 chassTotalNoOfClSlt	1.3.6.1.4.1.164.3.3.1.2.1.4	Integer32	read-only	This object indicates the number of physical Common Logic slots in the chassis.
I32 chassTotalNoOfMlSlt	1.3.6.1.4.1.164.3.3.1.2.1.5	Integer32	read-only	This object indicates the number of physical Main Link slots in the chassis (Kmux).
sysDcl	1.3.6.1.4.1.164.3.3.1.2.2
sysDclTable	1.3.6.1.4.1.164.3.3.1.2.2.1		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
sysDclEntry	1.3.6.1.4.1.164.3.3.1.2.2.1.1		not-accessible	An entry in table.
I32 sysDclCnfgIdx	1.3.6.1.4.1.164.3.3.1.2.2.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. For devices that work on line with NMS (no Temp configuration in NMS), Get and Set will be performed with index value of sysDclCnfgIdx = 1.
INT sysDclRedundancy	1.3.6.1.4.1.164.3.3.1.2.2.1.1.2	INTEGER	read-write	DCL redundancy desired state.
INT sysDclActiveCl	1.3.6.1.4.1.164.3.3.1.2.2.1.1.3	INTEGER	read-write	Active desired DCL. When 'auto' is selected, the system automatically selects the active DCL.
I32 sysDclFlipDelay	1.3.6.1.4.1.164.3.3.1.2.2.1.1.4	Integer32	read-write	If one DCL flip occurred and a second one should be performed, the time from the previous flip is checked. If the time is shorter than the delay specified here, the system should delay the flip operation until time reaches the specified delay. For DXC the values are 1 minute to 4 minutes (1..4). For Optimux-155-1 and Optimux-155-3 the values are: 0...60 Sec. 0 means No Delay.
INT sysDclFlipUponStnClk	1.3.6.1.4.1.164.3.3.1.2.2.1.1.5	INTEGER	read-write	This object allows user to decide (yes/no) if Agent should Flip from one DCL card to another, when there is Station Clock Fail in the Online DCL card.
I32 sysDclChFailThreshold	1.3.6.1.4.1.164.3.3.1.2.2.1.1.6	Integer32	read-write	This object indicates the number of failed channels that will trigger the redundancy procedure.
OCT sysDclChPriority	1.3.6.1.4.1.164.3.3.1.2.2.1.1.7	OCTET STRING	read-write	This object indicates the Priority for all the channels in the Main Access (Common Logic) card. Each channel is represented by 1 bit. The order of the bits in each byte is from Right to Left (LSB Bit to MSB) starting from BIT 0: 7 6 5 4 3 2 1 0 Channel no. 1 is represented by bit 0. Channel no. 2 is represented by bit 1. Channel no. n is represented by bit n-1. The value of the bit shows the priority. For bit value = 1, Priority = High. For bit value = 0, Priority = Low.
INT sysDclConfigDownloadSrc	1.3.6.1.4.1.164.3.3.1.2.2.1.1.8	INTEGER	read-write	In case of mismatch between the 2 CL card's configuration, the user can decide which card has the suitable configuration. The selected configuration will be downloaded from card A to card B if the value is dclA(2) or from card B to card A if the value is dclB(3). off(1) is used by part of the devices. In this case, after operation ends - value should be automatically set to off(1), which is the default state.
INT sysDclSwDownloadSrc	1.3.6.1.4.1.164.3.3.1.2.2.1.1.9	INTEGER	read-write	In case of mismatch between the 2 CL card's software, the user can decide which card has the suitable SW. The selected SW will be downloaded from card A to card B if the value is dclA(2) or from card B to card A if the value is dclB(3). off(1) is used by part of the devices. In this case, after operation ends - value should be automatically set to off(1), which is the default state.
BIT sysDclRedundancyStatus	1.3.6.1.4.1.164.3.3.1.2.2.1.1.10	Bits	read-only	Bit map representing current Redundancy Status. bit 0 - Indicates mismatch between the 2 CL cards' Configuration bit 1 - Indicates mismatch between the 2 CL cards' Software. bit 2 - Indicates CL card A Absence. bit 3 - Indicates CL card B Absence. bit 4 - Indicates Loss of Communication between the 2 CL cards. bit 5 - Indicates mismatch between the 2 CL cards' Hardware. bit 6 - Indicates Configuraton update is in process. bit 7 - Indicates Software update is in process.
INT sysDclOnline	1.3.6.1.4.1.164.3.3.1.2.2.2	INTEGER	read-only	The active Dcl card of the agent.
sysDclCopyDbTable	1.3.6.1.4.1.164.3.3.1.2.2.3		not-accessible	This table enables to copy a cofiguration from the Offline Dcl to the Online Dcl.
sysDclCopyDbEntry	1.3.6.1.4.1.164.3.3.1.2.2.3.1		not-accessible	An entry in table.
I32 sysDclCopyDbIdx	1.3.6.1.4.1.164.3.3.1.2.2.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed.
INT sysDclCopyDbCmd	1.3.6.1.4.1.164.3.3.1.2.2.3.1.2	INTEGER	read-write	When this command is sent to the agent, on(3), the Database specified (Db Idx), will be copied from the Offline Dcl to the Online Dcl. Afterwards the value of this object will automatically change to off(2).
INT sysDclFlipCmd	1.3.6.1.4.1.164.3.3.1.2.2.4	INTEGER	read-write	When the 'flip(3)' command is received by Agent, it will flip (switch) between Offline Dcl and Online Dcl cards. Afterwards the value of this object will automatically change to off(2).
sysStatus	1.3.6.1.4.1.164.3.3.1.3
INT sysSDateFormat	1.3.6.1.4.1.164.3.3.1.3.1	INTEGER	read-write	This object indicates the date and time format used for the sysSDateAndTimeCmd and for the alarm buffer report.
STR sysSDateCmd	1.3.6.1.4.1.164.3.3.1.3.2	DisplayString	read-write	This object indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the sysSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent. * For KM-2100 V1 and FCD-T1/E1 - the string should contain '/' signs between day, month and year. Example: 12/08/1998. * For DXC and rest of the products - the string should contain '-' signs between day, month and year. Example: 12-08-1998. The day value will be in the range: 1..31. The month value will be in the range: 1..12. The year value will be in the range: 1996..2050 for products supporting the '-' format.
STR sysSTimeCmd	1.3.6.1.4.1.164.3.3.1.3.3	DisplayString	read-write	This object indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent. The string should contain ':' signs between hour, minute and second. Example: 11:05:58.
I32 sysSActiveCnfg	1.3.6.1.4.1.164.3.3.1.3.4	Integer32	read-only	This object specifies the configuration number, that is currently active and running.
I32 sysSEditCnfg	1.3.6.1.4.1.164.3.3.1.3.5	Integer32	read-only	This object indicates the unique configuration number that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process.
INT sysSEditBy	1.3.6.1.4.1.164.3.3.1.3.6	INTEGER	read-only	This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after a load operation.
INT sysSClkSrc	1.3.6.1.4.1.164.3.3.1.3.7	INTEGER	read-only	This entry indicates the source of the system clock.
INT sysSAlrStatus	1.3.6.1.4.1.164.3.3.1.3.8	INTEGER	read-only	Indicates the current alarm state only for system level. This object will be : - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT sysSAlrStatusAll	1.3.6.1.4.1.164.3.3.1.3.9	INTEGER	read-only	Indicates the current alarm state including all levels: system, card, port. - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT sysSTestStatus	1.3.6.1.4.1.164.3.3.1.3.10	INTEGER	read-only	Indicates the current test status (for all levels: system, card, port). This attribute will be set to: - on(3): when there is at least one test in progress on the system/card/port otherwise the value will be off(2).
INT sysSSanityCheckStatus	1.3.6.1.4.1.164.3.3.1.3.11	INTEGER	read-only	Upon completion of the Sanity Check process on the TmpCnfg this object will be set to: - fail(2): when there is at least one error (which is not just a warning) encountered otherwise, - warning(3): when there are only warnings otherwise, - ok(4). The value should be unknown(1), if the TmpCnfg was changed after the last Sanity check.
I32 sysSNoOfSanityCheckErr	1.3.6.1.4.1.164.3.3.1.3.12	Integer32	read-only	This object indicates the number of errors/warnings discovered by the last Sanity Check process.
sysSErrListTable	1.3.6.1.4.1.164.3.3.1.3.13		not-accessible	A table.
sysSErrListEntry	1.3.6.1.4.1.164.3.3.1.3.13.1		not-accessible	An entry in table.
INT sysSErrType	1.3.6.1.4.1.164.3.3.1.3.13.1.1	INTEGER	read-only	The errors are recorded in the agent, in two separate lists, according to their type: error or warning.
I32 sysSErrIdx	1.3.6.1.4.1.164.3.3.1.3.13.1.2	Integer32	read-only	Unique index number to identify an entry in the error or warning list . The maximum value cannot exceed the value of 'sysSNoOfSanityCheckErr' (actually, the sum of the Errors list max. index and the Warning list max. index should equal the value of'sysSNoOfSanityCheckErr').
STR sysSErrDescription	1.3.6.1.4.1.164.3.3.1.3.13.1.3	DisplayString	read-only	This object is a full text description of the sanity check error including error code, IO slot and port numbers related to the code .
I32 sysSMaxNoOfCnfg	1.3.6.1.4.1.164.3.3.1.3.14	Integer32	read-only	Maximum number of configurations that can be defined and stored in the DACS agent. If the DACS agent has a large capacity, the maximum will be limited to 254.
I32 sysSSelfTestResult	1.3.6.1.4.1.164.3.3.1.3.15	Integer32	read-only	The test is performed by the active Common Logic card. The result will be a sum of 2**n according to the following bit convention: For DXC: bit 0 Database 1 Checksum Error (LSB) bit 1 Database 2 Checksum Error bit 2 I/O Expander Error bit 3 Counter Error bit 4 Matrix DPR Error bit 5 PS-A 5 Volt Error bit 6 PS-A 12 Volt Error bit 7 PS-B 5 Volt Error bit 8 PS-B 12 Volt Error bit 9 EPROM Failure For FCD: bit 0 I/O Expander Error (LSB) bit 1 Counter Error bit 2 EPROM Failure bit 3 Illegal Sys Config bit 4 SFIFO bit 5 EPIC Failure (ISDN) bit 6 XL Flash Fail -- for MSDSL interface bit 7 XL MITEL Fail -- for MSDSL interface bit 8 XL Framer Fail -- for MSDSL interface bit 9 XL DSP Fail -- for MSDSL interface For LRS52 - refer to product's spec When a bit is ('1'), the error exists. When NO ERROR is encountered, this object's value will be 0.
INT sysSRelayState	1.3.6.1.4.1.164.3.3.1.3.16	INTEGER	read-only	Indicates the current state of the alarm relay. notApplicable - for agents that do not support this object.
INT sysSInvertedAlr	1.3.6.1.4.1.164.3.3.1.3.17	INTEGER	read-only	Indicates if there is any Inverted alarm at any level of the system (sys, card, port). notApplicable - for agents that do not support this object.
sysSRdnFlipTable	1.3.6.1.4.1.164.3.3.1.3.18		not-accessible	This table includes all the Flip events due to I/O Redundancy since last Clear command of this table.
sysSRdnFlipEntry	1.3.6.1.4.1.164.3.3.1.3.18.1		not-accessible	An entry in table.
I32 sysSRdnFlipIdx	1.3.6.1.4.1.164.3.3.1.3.18.1.1	Integer32	read-only	Unique index number to identify an entry in the Redundancy Flip list.
INT sysSRdnFlipSlot	1.3.6.1.4.1.164.3.3.1.3.18.1.2	INTEGER	read-only	The slot number from which Flip was performed.
I32 sysSRdnFlipPort	1.3.6.1.4.1.164.3.3.1.3.18.1.3	Integer32	read-only	The port number from which Flip was performed. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 100=notApplicable (when Redundancy is at card level).
STR sysSRdnFlipCause	1.3.6.1.4.1.164.3.3.1.3.18.1.4	DisplayString	read-only	The last cause that caused the Flip from the Slot (Port) of sysSRdnSlot, sysSRdnPort.
STR sysSRdnFlipDate	1.3.6.1.4.1.164.3.3.1.3.18.1.5	DisplayString	read-only	Flip event Date. The format will be the one selected by user for sysSDateFormat.
STR sysSRdnFlipTime	1.3.6.1.4.1.164.3.3.1.3.18.1.6	DisplayString	read-only	Flip event Time. The format will be hh:mm:ss.
INT sysSRdnFlipTableClearCmd	1.3.6.1.4.1.164.3.3.1.3.19	INTEGER	read-write	This command, when Set to 'on', clears the Redundancy Flip table (sysSRdnFlipTable). After clear is performed, the agent will turn the value to 'off' automatically.
OID sysSRdnFlipCmd	1.3.6.1.4.1.164.3.3.1.3.20	OBJECT IDENTIFIER	read-write	This object enables the user to send a command to the Agent, to Flip from a current Online IO card to its Redundant card. The value sent will be an Object Identifier of an entry in the sysCRdnTable. This entry defines the Redundant couple of Slots on which the Flip is applied. Setting this object, will cause the Agent to Flip from current Online card to its Redundant card. This manual flip command is applicable only for entries having Redundancy Mode=Y Cable. For Vmux: This command will cause flipping from Secondary or Third Link to the Primary Link. If the active link is the primary link, the agent will flip to the secondary link. The value sent will be the Object Identifier of the following Table: agnCBuMlTable. Agent will send the value 0 for Get.
sysSBusTable	1.3.6.1.4.1.164.3.3.1.3.21		not-accessible	This table includes data and status about the internal DXC BUS.
sysSBusEntry	1.3.6.1.4.1.164.3.3.1.3.21.1		not-accessible	An entry in table.
I32 sysSBusPortIdx	1.3.6.1.4.1.164.3.3.1.3.21.1.1	Integer32	read-only	The DXC BUS port number: - first two digits will be: (IO slot number+10) - last one/two digits will be the Bus port number, in odd numbers: port1 = 1 port2 = 3 Example: port2 of IO slot 11 will be: 213.
INT sysSBusStatus	1.3.6.1.4.1.164.3.3.1.3.21.1.2	INTEGER	read-only	The Status of sysSBusPortIdx. free - not used physical - captured by the port of the card physically installed virtual - captured virtually by another port. Example: DIM port (by Destination) or by Transparent T3/E3 port.
I32 sysSBusCapturePort	1.3.6.1.4.1.164.3.3.1.3.21.1.3	Integer32	read-only	The Port that Captured the sysSBusPortIdx. - if sysSBusStatus=free, the value will be 'none'=0 - else, if sysSBusStatus=fixed, the value will be: sysSBusPortIdx - else, the value will be according to the port index that captured this Bus Port (according to DXC port index convention): - xx1, xx3, xx11, xx13, xx31, xx33, xx2..xx56(even numbers) - xx = (IO slot number+10)
I32 sysSBusUtilization	1.3.6.1.4.1.164.3.3.1.3.21.1.4	Integer32	read-only	Utilization of sysSBusPortIdx resources, in percent [%].
sysSRdnCmdTable	1.3.6.1.4.1.164.3.3.1.3.22		not-accessible	This table includes commands used for IO Redundancy.
sysSRdnCmdEntry	1.3.6.1.4.1.164.3.3.1.3.22.1		not-accessible	An entry in table.
INT sysSRdnEnforcedChannel	1.3.6.1.4.1.164.3.3.1.3.22.1.1	INTEGER	read-write	This is a command to override all switching considerations and enforce use of primary/ secondary connection only. noEnforcement - cancels the state of override and goes back to usual switching considerations. Default = noEnforcement(2).
INT sysSRdnLockFlip	1.3.6.1.4.1.164.3.3.1.3.22.1.2	INTEGER	read-write	This is a command to lock the Redundancy flip for this redundancy couple. Default = off(2).
INT sysSRdnManualFlip	1.3.6.1.4.1.164.3.3.1.3.22.1.3	INTEGER	read-write	This is a command to move to manual Redundancy flip mode for this redundancy couple. Default = off(2).
I32 sysSAlrAttrIndication	1.3.6.1.4.1.164.3.3.1.3.23	Integer32	read-only	This object indicates the status of the Alarm Attributes for the whole device. It is a sum of 2**(Bit-1). A Bit will be '1', when any alarm in the device is Filtered/Masked/Inverted (respectively). The Bit assignment is: Bit 1: Filter (LSB) Bit 2: Mask Bit 3: Invert (MSB). Examples: - Alarms are filtered and masked but not inverted: value=3 - Alarm is Inverted (not filtered or masked): value=4 - Alarm is masked (not inverted or filtered): value=2
sysCurrentAlr	1.3.6.1.4.1.164.3.3.1.4
sysSAlrTable	1.3.6.1.4.1.164.3.3.1.4.1		not-accessible	List of system level current existing alarms .
sysSAlrEntry	1.3.6.1.4.1.164.3.3.1.4.1.1		not-accessible	An entry in table.
I32 sysSAlrIdx	1.3.6.1.4.1.164.3.3.1.4.1.1.1	Integer32	read-only	An index number of the current system alarms.
I32 sysSAlrCode	1.3.6.1.4.1.164.3.3.1.4.1.1.2	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
INT sysSAlrState	1.3.6.1.4.1.164.3.3.1.4.1.1.3	INTEGER	read-only	This object indicates the alarm Severity.
INT sysSAlarmMask	1.3.6.1.4.1.164.3.3.1.4.1.1.4	INTEGER	read-only	Alarm Mask is : on/off.
INT sysSAlarmInvert	1.3.6.1.4.1.164.3.3.1.4.1.1.5	INTEGER	read-only	Alarm Invert is : on/off.
INT sysSAlarmOnOff	1.3.6.1.4.1.164.3.3.1.4.1.1.6	INTEGER	read-only	Alarm state is : on/off.
I32 sysSAlarmCounter	1.3.6.1.4.1.164.3.3.1.4.1.1.7	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
INT sysSAlrClearCmd	1.3.6.1.4.1.164.3.3.1.4.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the system level alarms . Upon completion, the value will automatically change to off(2).
INT sysSAlrClearAllCmd	1.3.6.1.4.1.164.3.3.1.4.3	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on all levels alarms . Upon completion, the value will automatically change to off(2).
INT sysSAlrMaskAll	1.3.6.1.4.1.164.3.3.1.4.4	INTEGER	read-write	on(3) - will cause masking of all the system level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all system level alarms except those masked via the sysSAlrMask.
OCT sysSAlrMask	1.3.6.1.4.1.164.3.3.1.4.5	OCTET STRING	read-write	This object is a mask that indicates which system level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the system level will be 0. This object is applicable only when sysSAlrMaskAll=off (otherwise all system alarms are masked). Example: When Alarms having the codes 6 and 11 are masked, the value of this object will be 840 (hex).
INT sysSAlrDataUpdateCmd	1.3.6.1.4.1.164.3.3.1.4.6	INTEGER	read-write	on(3) - will cause Update of the Alarms Severity, Attributes and Report tables. off(2) - Upon completion, the value will automatically change to off(2).
sysBufferAlr	1.3.6.1.4.1.164.3.3.1.5
sysBufferAlrTable	1.3.6.1.4.1.164.3.3.1.5.1		not-accessible	List of current existing alarms (of all levels).
sysBufferAlrEntry	1.3.6.1.4.1.164.3.3.1.5.1.1		not-accessible	An entry in table.
I32 sysBufferAlrIdx	1.3.6.1.4.1.164.3.3.1.5.1.1.1	Integer32	read-only	An index number of the current alarms.
I32 sysBufferAlrCode	1.3.6.1.4.1.164.3.3.1.5.1.1.2	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and thir related descriptions will be known by the NMS (for display purpose) and will appear in the unit's user manual.
INT sysBufferAlrState	1.3.6.1.4.1.164.3.3.1.5.1.1.3	INTEGER	read-only	This object indicates the alarm type. minor/major/warning/critical - indicates appearance of the problem and the type. event - indicates occurence of an event. off - indicates disappearance of an alarm.
INT sysBufferAlrSlot	1.3.6.1.4.1.164.3.3.1.5.1.1.4	INTEGER	read-only	The slot number this alarm refers to. When the alarm refers to a system function OR the DACS agent is a stand-alone unit, the value will be 'notApplicable(255)'. local/remote - for OP-4 device.
I32 sysBufferAlrPort	1.3.6.1.4.1.164.3.3.1.5.1.1.5	Integer32	read-only	The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999.
STR sysBufferAlrDate	1.3.6.1.4.1.164.3.3.1.5.1.1.6	DisplayString	read-only	The date when the alarm occured. The format will be according to sysSDateFormat.
STR sysBufferAlrTime	1.3.6.1.4.1.164.3.3.1.5.1.1.7	DisplayString	read-only	The time when the alarm occured.
TIK sysBufferAlrUpTime	1.3.6.1.4.1.164.3.3.1.5.1.1.8	TimeTicks	read-only	The time when the alarm occured. This parameter holds the sysUpTime value when the alarm occured.
STR sysBufferAlrInfo	1.3.6.1.4.1.164.3.3.1.5.1.1.9	SnmpAdminString	read-only	This parameter includes information about the alarm (additional to the Description).
INT sysBufferAlrClearCmd	1.3.6.1.4.1.164.3.3.1.5.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2).
sysConfig	1.3.6.1.4.1.164.3.3.1.6
sysCClkSrcTable	1.3.6.1.4.1.164.3.3.1.6.1		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. For devices with more than one configuration: The write operation into the Table Objects is valid only for the TmpCnfg entry.
sysCClkSrcEntry	1.3.6.1.4.1.164.3.3.1.6.1.1		not-accessible	An entry in table.
I32 sysCClkCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. It can be also a combination of the configuration number and the Card/Port/Other System index.
INT sysCClkSrcIdx	1.3.6.1.4.1.164.3.3.1.6.1.1.2	INTEGER	read-only	An index in the table. There are only two entries in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
INT sysCClkSrcMode	1.3.6.1.4.1.164.3.3.1.6.1.1.3	INTEGER	read-write	This entry indicates the source the nodal timing is locked to. none - is an invalid option for Master clock. internal - is an invalid option for Fallback clock . station - is an invalid option for a stand-alone unit. lbt - loop-back timing ntr - Network Time Reference adaptive - clock locking is achieved by altering the clock according to the data load system - irrelevant when sysCClkCnfgIdx refers to System Clock. sSubSystem - SONET/SDH Sub System. recovered - clock recovery. notApplicable - for ML source of Kmux or ML Timing combinations when Master/Fallback clock are not applicable.
I32 sysCClkSrcPrt	1.3.6.1.4.1.164.3.3.1.6.1.1.4	Integer32	read-write	This entry is valid only when working in rxClk mode (for IPmux1000 this entry will be valid whe working in LBT mode). For ACE2002 in case of invalid entry the return value will be 0. For other products in case of invalid entry the return value will be 9999. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The SP ports will be numbered as follows: - SP port 1 : 1 - SP port 2 : 2 For external ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Kmux, the port will be according to : Slot*100+Ch. For ACE2002, LA140 and IPmux1000 (GMUX), the port will be ifIndex.
INT sysCClkStationFreq	1.3.6.1.4.1.164.3.3.1.6.1.1.5	INTEGER	read-write	This entry indicates the frequency of the station clock when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'.
I32 sysCClkRevertiveTimeout	1.3.6.1.4.1.164.3.3.1.6.1.1.6	Integer32	read-write	The time in seconds in which the system will monitor the higher level clock source, before decision to revert to that clock. In case the time is zero, revertive mode will be disabled.
INT sysCClkStationIf	1.3.6.1.4.1.164.3.3.1.6.1.1.7	INTEGER	read-write	This entry indicates the electrical interface connected to the station clock, when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkStationCableMode	1.3.6.1.4.1.164.3.3.1.6.1.1.8	INTEGER	read-write	This parameter indicates whether both Station clocks get their clock from the same source (Y Cable)or each one get its clock independently. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkStationOutState	1.3.6.1.4.1.164.3.3.1.6.1.1.9	INTEGER	read-write	This parameter indicates whether station clock can send its clock to another device. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkSsmBased	1.3.6.1.4.1.164.3.3.1.6.1.1.10	INTEGER	read-write	This parameter indicates whether clock source will be selected based on receive clock quality, indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging). It is relevant only for sysCClkSrcIdx=master. When the value is Yes, sysCClkSrcMode must be notApplicable.
INT sysCClkSSubsystemSlot	1.3.6.1.4.1.164.3.3.1.6.1.1.11	INTEGER	read-write	This entry indicates the Slot from which the S Subsytem Source will be taken. The value will be applicable only when the sysCClkSrcMode is 'sSubsystem'.
U32 sysCClkRecoveredID	1.3.6.1.4.1.164.3.3.1.6.1.1.12	Unsigned32	read-write	This entry indicates the Recovered Clock ID. The value will be applicable only when sysCClkSrcMode is 'recovered'.
sysCnfgTable	1.3.6.1.4.1.164.3.3.1.6.2		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
sysCnfgEntry	1.3.6.1.4.1.164.3.3.1.6.2.1		not-accessible	An entry in table.
I32 sysCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. For Gmux2000 the range limitation (1..255) was discarded since the Idx is computed as: x 1000 + 255.
INT sysCMatrixMode	1.3.6.1.4.1.164.3.3.1.6.2.1.2	INTEGER	read-write	Indicates the TS Matrix Mode: bidirectional - TS Assignment Matrix is symmetric. unidirectional - TS Assignment Matrix can be asymmetric. notApplicable - for agents that do not support this feature.
INT sysCIsdnFormat	1.3.6.1.4.1.164.3.3.1.6.2.1.3	INTEGER	read-write	ISDN format. This parameter controls the operation mode of the ISDN ports. te - ISDN timing is derived from the signal received from the equipment it is connected to. nt - timing of the transmit path is locked to the nodal timing source. notApplicable - for agents that do not support this feature.
INT sysCRoutingOnEth	1.3.6.1.4.1.164.3.3.1.6.2.1.4	INTEGER	read-write	Mng Routing Protocol on the online CL Ethernet port, or on device Ethernet port dedicated for mangement.
INT sysCAutoConfigEnable	1.3.6.1.4.1.164.3.3.1.6.2.1.5	INTEGER	read-write	This object enables user to enable/disable activating the Auto Configuration. When Auto Configuration is activated, the device learns its configuration Automatically from the Net it is connected to.
INT sysCIntTsAllocMode	1.3.6.1.4.1.164.3.3.1.6.2.1.6	INTEGER	read-write	This object enables user to select the mode of Internal TS Allocation. static - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). This number will be allocated to the ports, so that if number of connected TSs will grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports. dynamic- TS allocation is done dynamically according to the connected TSs. No future reservations are done. This mode may cause data disruption on other ports/slots if user will want to change the number of connected TSs for a Dynamic card port. staticOneToOne - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). In addition, the TSs themselves cannot be higher than this defined Maximum (e.g if Maximum TSs=5 user cannot selects TSs higher than 5). This mode ensures that if number of TSs grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports AND for the selected port itself. Default=static(2).
INT sysCBuPrimaryPort	1.3.6.1.4.1.164.3.3.1.6.2.1.7	INTEGER	read-write	This object enables the user to configure a Backup mechanism. If a backup mechanism exists, it is possible to configure the primary port. The traffic will flow via the primary port when the port functionality is OK. In Vmux-2100 device the backup mechanism is relevant for the Main Board only. The primary port can be the E1/T1/Serial port or the ETH port.
INT sysCEnableLanOverTdm	1.3.6.1.4.1.164.3.3.1.6.2.1.8	INTEGER	read-write	This object enables/disables transferring traffic from the LAN port to the TDM port. It is possible to enable only part of the traffic on the TDM port for security reasons or in order to minimize the bandwidth .
I32 sysCSs7FisuSuppression	1.3.6.1.4.1.164.3.3.1.6.2.1.9	Integer32	read-write	SS7 Suppresion is used for SS7 Spoofing. The SS7 spoofing terminates the keep alive messages from the local VMUX without sending them over the network, thus improving the bandwidth utilization. FISU means Fill in Service Unit - Keep alive that is sent when no one is talking on the line. This object enables the configuration of the SS7 Keep Alive packet % that will be discarded. Legal Values: 0 - No Suppression, 10%, 20%, 30% .. 90% Example: For a value of 10, 1 keep alive packet will be discarded out of 10 keep alive packets that were supposed to be sent over the network.
INT sysCBuRecMode	1.3.6.1.4.1.164.3.3.1.6.2.1.10	INTEGER	read-write	Recovery Mode. This object determines if after recovery of the Primary Link (used in Vmux) it will become on-line again or not: auto - automatic. In this case, the failed Link will become on-line again after recovery, automatically. manual - In this case, the failed Link will not become on-line again after recovery but user can manually flip to this Link.
sysCRdnTable	1.3.6.1.4.1.164.3.3.1.6.3		not-accessible	Configuration of all Redundant I/O cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that have no Redundancy, will not exist in this table.
sysCRdnEntry	1.3.6.1.4.1.164.3.3.1.6.3.1		not-accessible	An entry in table.
I32 sysCRdnCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
INT sysCRdnPrimeSlot	1.3.6.1.4.1.164.3.3.1.6.3.1.2	INTEGER	read-only	The slot number of the Primary card of Redundancy. The Primary card should be the card that user wishes to be the online card (usually the more important one). For some Redundancy modes the importance of the redundant cards/ports is the same.
I32 sysCRdnPrimePort	1.3.6.1.4.1.164.3.3.1.6.3.1.3	Integer32	read-only	The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For an IP Bundle that is in an External Device (not in this MP), the value will be: 70,000 + ifIndex of Secondary Bundle. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level).
INT sysCRdnSecSlot	1.3.6.1.4.1.164.3.3.1.6.3.1.4	INTEGER	read-create	The slot number of the Secondary card of Redundancy matching the Primary slot.
I32 sysCRdnSecPort	1.3.6.1.4.1.164.3.3.1.6.3.1.5	Integer32	read-create	The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For an IP Bundle that is in an External Device (not in this MP), the value will be: 0. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level).
INT sysCRdnMode	1.3.6.1.4.1.164.3.3.1.6.3.1.6	INTEGER	read-create	Redundancy Mode. DXC supports: yCable(3), singleSlotProtection(6) and dualCableParallelTx(4) MP supports: yCable(3), dualCableParallelTx(4), onePlusOne(7) and oneToOne(8). (dualCableAIS and backup were planned for MP but were not implemented). backup - will be used when a port is backup of more than one port. IPmux: onePlusOne(7) and oneToOne(8) are used for Bundle redundancy.
INT sysCRdnRecMode	1.3.6.1.4.1.164.3.3.1.6.3.1.7	INTEGER	read-create	Recovery Mode. This object determines if after recovery of the failed Primary card/port it will become on-line again or not: auto - automatic . In this case, the failed card/port will become on-line again after recovery, automatically. manual - In this case, the failed card/port will not become on-line again after recovery. But, user can manually flip to this card/port. nonRevertive - same as manual, but here user CANNOT manually flip to this card/port. It will become on-line again, only if the Secondary/Backup card/port will fail.
I32 sysCRdnRecTime	1.3.6.1.4.1.164.3.3.1.6.3.1.8	Integer32	read-create	Redundancy Recovery Time (sec). After switching to the current online card, the next switch can be performed only after a minimum time, indicated by this object. Valid Values: 0..300, 65535. 65535=NA. This object is applicable only when sysCRdnRecMode=auto.
INT sysCRdnHwSwFlip	1.3.6.1.4.1.164.3.3.1.6.3.1.9	INTEGER	read-create	HW or SW decision for Redundancy Flip. This object is applicable only for sysCRdnMode=singleSlotProtection. HW - decision is by I/O card SW - decision is by CL SW.
ROW sysCRdnRowStatus	1.3.6.1.4.1.164.3.3.1.6.3.1.10	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table. The possible supported RowStatus values are active (1) and destroy (6). For Vmux-2100 the supported values are: active (1), createAndGo (4) and destroy (6).
INT sysCRdnOnline	1.3.6.1.4.1.164.3.3.1.6.3.1.11	INTEGER	read-only	Status - who is the Online (current) Redundancy Slot/Port. This object shows only the Online Slot/Port regarding the Redundancy. mdlSActivity or prtGenActiveStatus of the same Slot/Port may be Offline.
INT sysCRdnSwitchingMode	1.3.6.1.4.1.164.3.3.1.6.3.1.12	INTEGER	read-create	This object defines which Self Healing Ring (SHR) SDH ring is used: Uni Directional or BiDirectional. The type of the ring is defined according to the direction of traffic flow under normal working conditions. In Bi Directional ring, the duplex traffic is on the same path and transverses the same set of nodes for both directions of transmission. In Uni Directional ring, the duplex traffic travels over opposite path (per direction) and all the node of the ring are involved. For Uni Directional SHR Protection Switching (Single Ended Switching) is controlled by one node of the SDH ring, and does not require a protocol. For Bi Directional SHR Protection Switching (Dual Ended switching) is controlled by some nodes of the ring and requires a protocol
I32 sysCRdnFlipUponEvent	1.3.6.1.4.1.164.3.3.1.6.3.1.13	Integer32	read-create	This object allows user to define if Flip to the other port will be performed (or not), for certain possible events. Each event is represented by a bit. The value of the object is a sum of 2**n, according to the bits having '1' value. '1' - means that Flip should occur due to this event. Bit 0 (LSB) = SD (Signal Degraded). For IPmux: Bit 0 (LSB) = TDM Line LOS/LOF. Bit 1 = Sequence Number. Bit 2 = Jitter Buffer errors.
I32 sysCRdnLosOrLofTime	1.3.6.1.4.1.164.3.3.1.6.3.1.14	Integer32	read-create	This parameter determines how much time to wait before switching, after LOF or LOS are detected on the TDM Line. For Ipmux time is counted in msec.
I32 sysCRdnEventsTimeWindow	1.3.6.1.4.1.164.3.3.1.6.3.1.15	Integer32	read-create	This parameter determines the time window in which to count events to trigger protection switching. For Ipmux time is counted in seconds.
I32 sysCRdnSequenceNumberThreshold	1.3.6.1.4.1.164.3.3.1.6.3.1.16	Integer32	read-create	This parameter determines the number of Sequence Number errors that should occur in the time window in order to cause switching.
I32 sysCRdnBufferErrorsThreshold	1.3.6.1.4.1.164.3.3.1.6.3.1.17	Integer32	read-create	This parameter determines the number of Buffer undeflow/ overflow events occured in the time window that cause switching.
I32 sysCRdnBuffUnderrunTime	1.3.6.1.4.1.164.3.3.1.6.3.1.18	Integer32	read-create	This parameter determines how much time to wait before switching, after jitter buffer underrun. Switching occurs if no frame arrives within that time. For Ipmux time is counted in msec.
INT sysCRdnPrimePriority	1.3.6.1.4.1.164.3.3.1.6.3.1.19	INTEGER	read-create	The Primary port priority. In ETX2xx/2xxA: When selecting sysCRdnMode = manual (10), this parameter determines the forced active port: low - means that the secondary port is selected to be active high - means that the primary port is selected to be active.
INT sysCRdnSecPriority	1.3.6.1.4.1.164.3.3.1.6.3.1.20	INTEGER	read-create	The Secondary port priority.
U32 sysCRdnWTR	1.3.6.1.4.1.164.3.3.1.6.3.1.21	Unsigned32	read-create	Redundancy Wait to Restore (sec). Valid Values: 0..999, 65535. 65535=NA. When the value <> 65535, the value of sysCRdnRecTime must be 65535.
STR sysCRdnName	1.3.6.1.4.1.164.3.3.1.6.3.1.22	SnmpAdminString	read-create	A textual name for the redundancy group.
U32 sysCRdnTxDownDurationUponFlip	1.3.6.1.4.1.164.3.3.1.6.3.1.23	Unsigned32	read-create	This object defines the duration (in seconds) the active port transmission is shut down after flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0 = no shut-down. This object is applicable only when sysCRdnMode = oneToOne(8) and mainly when each of the links of our device is connected to a different device.
sysDbase	1.3.6.1.4.1.164.3.3.1.7
INT sysDbaseSanityCheckCmd	1.3.6.1.4.1.164.3.3.1.7.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion, the value will automatically change to off(2).
I32 sysDbaseDownloadCnfgIdxCmd	1.3.6.1.4.1.164.3.3.1.7.2	Integer32	read-write	This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command, the DACS agent will initiate the Sanity-Check process. If successful, the actual transfer will be performed. If there will be errors, the user will have to perform the command again after errors correction. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg.
I32 sysDbaseUploadCnfgIdxCmd	1.3.6.1.4.1.164.3.3.1.7.3	Integer32	read-write	This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg.
sysDbaseFlipTable	1.3.6.1.4.1.164.3.3.1.7.4		not-accessible	Dbase Flip time and activation for every configuration.
sysDbaseFlipEntry	1.3.6.1.4.1.164.3.3.1.7.4.1		not-accessible	An entry in table.
I32 sysDbaseFlipIdx	1.3.6.1.4.1.164.3.3.1.7.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being the target Configuration.
STR sysDbaseFlipTime	1.3.6.1.4.1.164.3.3.1.7.4.1.2	DisplayString	read-write	This attribute indicates the time (HH:MM) when this data base will start being used by the Tmp config.
INT sysDbaseFlipActivation	1.3.6.1.4.1.164.3.3.1.7.4.1.3	INTEGER	read-write	This attribute indicates if the Dbase flip will be activated at the time specified for this configuration (enable) or not (disable). No more than one flip should be enabled for the same time.
mdlDacsMux	1.3.6.1.4.1.164.3.3.2
mdlGen	1.3.6.1.4.1.164.3.3.2.1
mdlSTable	1.3.6.1.4.1.164.3.3.2.1.1		not-accessible	A table.
mdlSEntry	1.3.6.1.4.1.164.3.3.2.1.1.1		not-accessible	An entry in table.
INT mdlSSltIdx	1.3.6.1.4.1.164.3.3.2.1.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the DACS. The Kilomux should use enumerated values starting with kmx. For IPmux100 use values 1-13, 20.
INT mdlSCardType	1.3.6.1.4.1.164.3.3.2.1.1.1.2	INTEGER	read-only	This attribute indicates the type of the card installed in the specific slot position. Only PS's are possible in the PS slots. Only CL's are possible in the CL slots. Only IO modules are possible in the IO slots. Kmux card type start with the letter k. LA card type start with the letters la.
STR mdlSHwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.3	DisplayString	read-only	This attribute indicates the Hardware version of the card installed in the specific slot position.
STR mdlSSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.4	DisplayString	read-only	This attribute indicates the Software version of the card installed in the specific slot position.
INT mdlSAlarmStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.5	INTEGER	read-only	Indicates the current alarm state only for card level. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT mdlSAlarmStatusAll	1.3.6.1.4.1.164.3.3.2.1.1.1.6	INTEGER	read-only	Indicates the current card alarm state including the lower level: card, port. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT mdlSTestStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.7	INTEGER	read-only	This attribute will be on(3) when there is at least one test running on a port of the module; otherwise the value will be off(2).
INT mdlSHwStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.8	INTEGER	read-only	This attribute will be fail(2) when a HW FAIL exists on this module (discovered by periodic self test); otherwise the value will be ok(3).
INT mdlSActivity	1.3.6.1.4.1.164.3.3.2.1.1.1.9	INTEGER	read-only	notApplicable - when the slot is empty (no module) offline(1) - when the module is not active (redundant) online (2) - when the module is active .
INT mdlSAlrClearCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.10	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the card level alarms . Upon completion, the value will automatically change to off(2).
INT mdlSAlrClearAllCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.11	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on card and port level alarms . Upon completion, the value will automatically change to off(2).
INT mdlSAlrMaskAll	1.3.6.1.4.1.164.3.3.2.1.1.1.12	INTEGER	read-write	on(3) - will cause masking of all the card level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all card level alarms except those masked via the mdlAlrMaskTable.
I32 mdlSCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.13	Integer32	read-write	General object for any special command at card level. 0=NotApplicable, for cards that don't support this object. For KML.10(ISDN) card of KM-2100, the object will indicate Manual Call Command in Switch mode. It is applicable only when for KML.10, prtIsdnSwitchMode=manual. KML.10 valid values: '1' = noOp, will be used by agents that do not support this feature or object (old KM agents) '2' = off, Set call command mode to disconnect state. Disconnects the call. '3' = on, Set call command mode to connect state. Connects the call. For DXC IO cards, the object will be used for IO Card Reset HW command: '2' = off, this will be always the Get value for these cards. '3' = on, this is the Set command used to Reset the IO card. Upon completing the operation, the value will automatically change to off(2), by Agent. For Slots that are NOT IO Slots and for empty IO Slots, the Get value will be always '0' (NotApplicable).
INT mdlSReset	1.3.6.1.4.1.164.3.3.2.1.1.1.14	INTEGER	read-write	Reset action to be performed on the module.
INT mdlSRebuildFrame	1.3.6.1.4.1.164.3.3.2.1.1.1.15	INTEGER	read-write	Applicable only for KiloMux Main Link cards only. '2' = off, this will be always the Get value. '3' = on, this is the Set command used to Rebuild the Frame. Upon completing the operation, the value will automatically change to off(2), by Agent.
STR mdlSBackupSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.16	DisplayString	read-only	This attribute indicates the Backup Software version of the card installed in the specific slot position.
STR mdlSSecondaryBackupSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.17	DisplayString	read-only	This attribute indicates the Secondary Backup Software version of the card installed in the specific slot position.
STR mdlSPiggybackVer	1.3.6.1.4.1.164.3.3.2.1.1.1.18	SnmpAdminString	read-only	This attribute indicates the Piggyback version of the card installed in the specific slot position.
mdlCTable	1.3.6.1.4.1.164.3.3.2.1.2		not-accessible	A table.
mdlCEntry	1.3.6.1.4.1.164.3.3.2.1.2.1		not-accessible	An entry in table.
I32 mdlCConfigIdx	1.3.6.1.4.1.164.3.3.2.1.2.1.1	Integer32	read-only	This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch).
INT mdlCSlotIdx	1.3.6.1.4.1.164.3.3.2.1.2.1.2	INTEGER	read-only	This object indicates a unique number of the slot position in which the module is inserted. The Kilomux should use enumerated values starting with kmx.
INT mdlCProgCardType	1.3.6.1.4.1.164.3.3.2.1.2.1.3	INTEGER	read-write	This object indicates the card type assigned to the specific slot in the common configuration. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. The write operation is valid only for the TmpCnfg entry.
I32 mdlCNoOfExtPrt	1.3.6.1.4.1.164.3.3.2.1.2.1.4	Integer32	read-only	Number of external ports in the programmed module of the specific slot position
I32 mdlCNoOfIntPrt	1.3.6.1.4.1.164.3.3.2.1.2.1.5	Integer32	read-only	Number of internal ports in the programmed module of the specific slot position.
I32 mdlCParam	1.3.6.1.4.1.164.3.3.2.1.2.1.6	Integer32	read-write	General configuration object at card level (per configuration). NotApplicable=0, for cards that don't support this object. For D8U and D16U cards of DXC, the object will indicate the port on which BERT will be performed. The port can be one of the external ports, any of its associated B1, B2, D ports or no port of the card (None=0). For port indexes see DXC R6 spec. For Gmux-2000, this parameter used for determining the Gigabit ETH exit port
mdlAlr	1.3.6.1.4.1.164.3.3.2.1.3
mdlAlrTable	1.3.6.1.4.1.164.3.3.2.1.3.1		not-accessible	The list of card alarms.
mdlAlrEntry	1.3.6.1.4.1.164.3.3.2.1.3.1.1		not-accessible	An entry in table.
I32 mdlAlrIdx	1.3.6.1.4.1.164.3.3.2.1.3.1.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive
INT mdlAlrSltIdx	1.3.6.1.4.1.164.3.3.2.1.3.1.1.2	INTEGER	read-only	This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.
I32 mdlAlrCode	1.3.6.1.4.1.164.3.3.2.1.3.1.1.3	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
INT mdlAlrState	1.3.6.1.4.1.164.3.3.2.1.3.1.1.4	INTEGER	read-only	This object indicates the card alarm severity.
INT mdlAlarmMask	1.3.6.1.4.1.164.3.3.2.1.3.1.1.5	INTEGER	read-only	Alarm Mask is : on/off.
INT mdlAlarmInvert	1.3.6.1.4.1.164.3.3.2.1.3.1.1.6	INTEGER	read-only	Alarm Invert is : on/off.
INT mdlAlarmOnOff	1.3.6.1.4.1.164.3.3.2.1.3.1.1.7	INTEGER	read-only	Alarm state is : on/off.
I32 mdlAlarmCounter	1.3.6.1.4.1.164.3.3.2.1.3.1.1.8	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
mdlAlrMaskTable	1.3.6.1.4.1.164.3.3.2.1.3.2		not-accessible	The list of card masked alarms.
mdlAlrMaskEntry	1.3.6.1.4.1.164.3.3.2.1.3.2.1		not-accessible	An entry in table.
INT mdlAlrMaskSltIdx	1.3.6.1.4.1.164.3.3.2.1.3.2.1.1	INTEGER	read-only	This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.
OCT mdlAlrMask	1.3.6.1.4.1.164.3.3.2.1.3.2.1.2	OCTET STRING	read-write	This object is a mask that indicates which card level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the card level will be 0. This object is applicable only when mdlSAlrMaskAll=off (otherwise all card alarms are masked). Example: When Alarm having the code 8 is masked, the value of this object will be 100 (hex).
mdlCl	1.3.6.1.4.1.164.3.3.2.2
mdlClTable	1.3.6.1.4.1.164.3.3.2.2.1		not-accessible	A table.
mdlClEntry	1.3.6.1.4.1.164.3.3.2.2.1.1		not-accessible	An entry in table.
INT mdlClIdx	1.3.6.1.4.1.164.3.3.2.2.1.1.1	INTEGER	read-only	This object indicates the Cl slot referred.
I32 mdlClSwchStatus	1.3.6.1.4.1.164.3.3.2.2.1.1.2	Integer32	read-only	This object indicates the status of the switches on the referred DCL card. Each switch is represented by a bit. The status is a sum of 2n, according to the bits. There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (21 + 2**0). When the status of the switches is unknown, the value of this object will be 255.
STR mdlClLastFlipDate	1.3.6.1.4.1.164.3.3.2.2.1.1.3	DisplayString	read-only	Date when last flip occured. The format would be as specified by the sysSDateFormat.
STR mdlClLastFlipTime	1.3.6.1.4.1.164.3.3.2.2.1.1.4	DisplayString	read-only	Time when last flip occured.
STR mdlClLastFlipCause	1.3.6.1.4.1.164.3.3.2.2.1.1.5	DisplayString	read-only	The cause of last flip.
mdlPs	1.3.6.1.4.1.164.3.3.2.3
mdlPsTable	1.3.6.1.4.1.164.3.3.2.3.1		not-accessible	A table.
mdlPsEntry	1.3.6.1.4.1.164.3.3.2.3.1.1		not-accessible	An entry in table.
INT mdlPsIdx	1.3.6.1.4.1.164.3.3.2.3.1.1.1	INTEGER	read-only	This object indicates the PS card referred.
INT mdlPsStatus	1.3.6.1.4.1.164.3.3.2.3.1.1.2	INTEGER	read-only	This object indicates the status of the PS card.
INT mdlPsTestResult	1.3.6.1.4.1.164.3.3.2.3.1.1.3	INTEGER	read-only	This object indicates the result of the PS card test. ok (1) - the test passed successfully. f12V (2) - 12V FAIL was detected f5V (3) - 5V FAIL was detected.
prtDacsMux	1.3.6.1.4.1.164.3.3.3
prtGen	1.3.6.1.4.1.164.3.3.3.1
prtGenParamTable	1.3.6.1.4.1.164.3.3.3.1.1		not-accessible	A table.
prtGenEntry	1.3.6.1.4.1.164.3.3.3.1.1.1		not-accessible	An entry in table.
I32 prtGenPrtIdx	1.3.6.1.4.1.164.3.3.3.1.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT prtGenSlt	1.3.6.1.4.1.164.3.3.3.1.1.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. The Kilomux should use the enumerated starting with kmx.
INT prtGenExtInt	1.3.6.1.4.1.164.3.3.3.1.1.1.3	INTEGER	read-only	This attribute describes the type of the designated port. Exteral port is a port with a physical connector. Internal port might be of two types, one is a composite port which collects data of a few external ports into a common bandwidth (usually routed trough DS1 link); the other type is internal ports which get only part of external port data (usually a few DS0's). In the Kilomux-2100, the internal(3) value is used for composite channels or sub-channels of an ISDN Ch.
I32 prtGenIfIndex	1.3.6.1.4.1.164.3.3.3.1.1.1.4	Integer32	read-only	This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx, the value will be '7fffffff'h.
INT prtGenActiveStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.5	INTEGER	read-only	This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the port is not connected according to the active config. offLine(3) indicates that the port is down (not working) due to any problem. onLine (4) indicates that the port is up (working) offLineRedundancy(5) indicates that the port is down because it is a redundant port. onLineRedundancy (6) indicates that this is a redundant port which is up and works as the active link.
INT prtGenAlrStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.6	INTEGER	read-only	Indicates the alarm state at port (ch) agent level. This object will be: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT prtGenTestStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.7	INTEGER	read-only	This attribute will be on(3) when there is at least one test in progress (running) on the port; otherwise the value will be off(2).
I32 prtGenTestMask	1.3.6.1.4.1.164.3.3.3.1.1.1.8	Integer32	read-only	This is a mask which indicates which tests from the 'prtGenTestCmd' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
I32 prtGenTestCmd	1.3.6.1.4.1.164.3.3.3.1.1.1.9	Integer32	read-write	Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMask). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the requested value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system.
I32 prtGenTestRunning	1.3.6.1.4.1.164.3.3.3.1.1.1.10	Integer32	read-only	This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only!
INT prtGenType	1.3.6.1.4.1.164.3.3.3.1.1.1.11	INTEGER	read-only	This object describes the type of the selected port. idsl - applicable for external ports of HS-U cards (of DXC) when interface is LT-1.
STR prtGenInterfaceType	1.3.6.1.4.1.164.3.3.3.1.1.1.12	DisplayString	read-only	This attribute indicates a unique HW interface type of the selected port. Examples: - for T1 cards: DSU, CSU - for E1 cards: DSU, LTU - for HS cards: v35, rs422, x21 etc...
INT prtGenAlrClearCmd	1.3.6.1.4.1.164.3.3.3.1.1.1.13	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the port level alarms . Upon completion, the value will automatically change to off(2). noOp - will be used by agents that do not support this feature or object.
INT prtGenAlrMaskAll	1.3.6.1.4.1.164.3.3.3.1.1.1.14	INTEGER	read-write	on(3) - will mask all the alarms of the selected port off(2)- will unmask all alarms of the selected port except the ones selected by the prtAlrMaskTable. noOp - will be used by agents that do not support this feature or object.
OCT prtGenParamStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.15	OCTET STRING	read-only	This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For HS cards (Dxc cards) - 1 octet: Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 0 and 1 indicates RTS control signal state: Bit 1: '1'=active ; '0'=notActive Bit 0 (LSB): '1'=unknown ; '0'=NA - For HS-U/1 external port (MP card, used in FCD-M) - 1 Octet: Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For VC-6, VC-12, VC-12/6 external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 \|___\| \|_______\| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=Unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|___________\| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For KM2100, KVF.5 cards - indicates the status of A and B signaling for each internal channel. 1 Octet: Bit - 7 6 5 4 3 2 1 0 \|_____\| \|_\| \|_\| spare B A Bit 0 (LSB) and Bit 1 : A status Bit 2 and Bit 3 : B status 00 - Off 01 - On 11 - Unknown - For FCD-W, NETWORK and USER ports - 1 Octet Status of Control Signals: '1'=On ; '0'=Off or when not applicable Bit - 7 6 5 4 3 2 1 0 Bit 7 (MSB) - Signal Loss (applicable only for G.703 interface) Bit 6 - CONTROL (applicable only for X.21 interface) Bit 5 - INDICATION (applicable only for X.21 interface) Bit 4 - DSR (applicable only for V.35 interface) Bit 3 - RTS (applicable only for V.35 interface) Bit 2 - CTS (applicable only for V.35 interface) Bit 1 - DTR (applicable only for V.35 interface) Bit 0 - DCD (applicable only for V.35 interface) - For DXC R6 , D8U, D16U External ports - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For DXC DE1-HDSL, DT1-HDSL, D16GSDSL, D8SL External ports - 2 Octets MSB octet: far-end modem channel interface LSB octet: Sub Link existence (Y/N), far-end modem type, synchronization with far-end modem MSB octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) 0000 1011 = IR-ETH-QN Rest of the combinations: reserved LSB octet: Bit 7 6 5 4 3 2 1 0 LSB \| \|___________\| \|__\| SL modem sync or Box material SL: modem: 00000 = other sync: 00 = not sync 0=not exist 00001 = unknown 01 = sync 1=exists 00010 = ASMi-31/2 10 = reserved 00011 = HCD-E1 11 = reserved Box material 00100 = HTU-E1 (for D8SL card): 00101 = HTU-2 0=metal 00110 = ASMi-52 SA/2W/Slave 1=plastic 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD 01110 = D8GSDSL card of DXC-3000 01111 = ASMi-52A Rest = reserved
INT prtGenRdnStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.16	INTEGER	read-only	This object indicates if this port is part of a redundant pair and in this case, if it is On or Off. none(1) - No redundancy or Not Applicable off (2) - the port is part of a redundant pair and it is Off from Redundancy point of view (not the port used). on (3) - the port is part of a redundant pair and it is On from Redundancy point of view (it is the port used).
OCT prtGenTestMaskXP	1.3.6.1.4.1.164.3.3.3.1.1.1.17	OCTET STRING	read-only	This is an Expanded test mask of the prtGenTestMask object. The prtGenTestMask object reached its maximum, being an Integer with 31 bits. This object indicates which tests from the 'prtGenTestCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
OCT prtGenTestCmdXP	1.3.6.1.4.1.164.3.3.3.1.1.1.18	OCTET STRING	read-write	This is an Expanded test command of the prtGenTestCmd object. The prtGenTestCmd object reached its maximum, being an Integer with 31 bits. Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMaskXP). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the requested value is 00000003 hex -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system.
OCT prtGenTestRunningXP	1.3.6.1.4.1.164.3.3.3.1.1.1.19	OCTET STRING	read-only	This is an Expanded object of the prtGenTestRunning object. The prtGenTestRunning object reached its maximum, being an Integer with 31 bits. This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only!
prtGenTestDurationTable	1.3.6.1.4.1.164.3.3.3.1.2		not-accessible	A table.
prtGenTestDurationEntry	1.3.6.1.4.1.164.3.3.3.1.2.1		not-accessible	An entry in table.
I32 prtGenTestPrtIdx	1.3.6.1.4.1.164.3.3.3.1.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT prtGenTestIdx	1.3.6.1.4.1.164.3.3.3.1.2.1.2	INTEGER	read-only	This attribute indicates the test, the duration refers.
I32 prtGenTestDuration	1.3.6.1.4.1.164.3.3.3.1.2.1.3	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to the specified test . The resolution will be a minute, and the maximum duration is limited to 30 minutes . A zero value specifies no time limitation. When the test isn't active the agent initiates this object to 2 min. when the duration is needed and to 0 if it's not required.
prtGenTsTable	1.3.6.1.4.1.164.3.3.3.1.3		not-accessible	The write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch),exept some products which enable direct writing to the ActiveCnfg. This is written in the respective product's spec.
prtGenTsEntry	1.3.6.1.4.1.164.3.3.3.1.3.1		not-accessible	An entry in table.
I32 prtGenTsCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
I32 prtGenTsPrtIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.2	Integer32	read-only	This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtGenTsIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.3	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 or HS Card . In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
INT prtGenTsType	1.3.6.1.4.1.164.3.3.3.1.3.1.4	INTEGER	read-write	The type of Timeslot. If the source or destination port is an HS port,'TS Type' must be 'data'. nc - means that this TimeSlot is not connected. voice, data, vcMP - also mean that this TS is connected. mng - means that this TS is dedicated to Management (not connected to another port.
I32 prtGenTsIConPrt	1.3.6.1.4.1.164.3.3.3.1.3.1.5	Integer32	read-write	This attribute indicates the internally (In Mux) connected port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside ports will be for example, the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * noConnection - will be indicated as 10 for DXC and FCD-E1/T1. - will be indicated as 100 for FCD-E1/I and SMODs. * Split TS (same TS is Split to several ports) - 11. * notApplicable- will be indicated as 100 for LRS IMODs. All HS port's timeslots must have the same destination port.
I32 prtGenTsIConTs	1.3.6.1.4.1.164.3.3.3.1.3.1.6	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 (or HS) Card. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling. * For DXC: All HS port's timeslots must start with Timeslot no.1
prtAlr	1.3.6.1.4.1.164.3.3.3.1.4
prtSAlarmTable	1.3.6.1.4.1.164.3.3.3.1.4.1		not-accessible	A table.
prtSAlarmEntry	1.3.6.1.4.1.164.3.3.3.1.4.1.1		not-accessible	An entry in table.
I32 prtSAlarmIdx	1.3.6.1.4.1.164.3.3.3.1.4.1.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive.
I32 prtSAlarmPrtIdx	1.3.6.1.4.1.164.3.3.3.1.4.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtSAlarmCode	1.3.6.1.4.1.164.3.3.3.1.4.1.1.3	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
INT prtSAlarmState	1.3.6.1.4.1.164.3.3.3.1.4.1.1.4	INTEGER	read-only	This object indicates the port alarm severity.
INT prtSAlarmMask	1.3.6.1.4.1.164.3.3.3.1.4.1.1.5	INTEGER	read-only	Alarm Mask is : on/off.
INT prtSAlarmInvert	1.3.6.1.4.1.164.3.3.3.1.4.1.1.6	INTEGER	read-only	Alarm Invert is : on/off.
INT prtSAlarmOnOff	1.3.6.1.4.1.164.3.3.3.1.4.1.1.7	INTEGER	read-only	Alarm state is : on/off.
I32 prtSAlarmCounter	1.3.6.1.4.1.164.3.3.3.1.4.1.1.8	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
prtAlrMaskTable	1.3.6.1.4.1.164.3.3.3.1.4.2		not-accessible	A table.
prtAlrMaskEntry	1.3.6.1.4.1.164.3.3.3.1.4.2.1		not-accessible	An entry in table.
I32 prtAlrMaskPrtIdx	1.3.6.1.4.1.164.3.3.3.1.4.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
OCT prtAlrMask	1.3.6.1.4.1.164.3.3.3.1.4.2.1.2	OCTET STRING	read-write	This object is a mask that indicates which port level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the port level will be 0. This object is applicable only when prtGenAlrMaskAll=off (otherwise all port alarms are masked). Example: When Alarms having the codes 31 and 40 are masked, the value of this object will be 10080000000 (hex).
prtBertTable	1.3.6.1.4.1.164.3.3.3.1.5		not-accessible	This table includes the BERT parameters, counters and commands. The configurable parameters: - prtBertPattern - prtBertInjectRate - prtBertTs are not Set per configuration (same for all Configurations) but start being applied by the Agent only upon successful Update/Download operation. Therefore, Set will enter the values to the Temporary Configuration of the agent, while Get will get the values of the Active Configuration.
prtBertEntry	1.3.6.1.4.1.164.3.3.3.1.5.1		not-accessible	An entry in table.
I32 prtBertPrtIdx	1.3.6.1.4.1.164.3.3.3.1.5.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the MP : - first two digits will be: (IO slot number+10) - last one/two digits will be according to the external port number within the card: exPrt1 -> 1 exPrt2 -> 3 exPrt3 -> 5 exPrt4 -> 7 .
INT prtBertPattern	1.3.6.1.4.1.164.3.3.3.1.5.1.2	INTEGER	read-write	This object indicates the pattern of the BERT. p2Exxm1 = 2Exx-1. pxx = pattern xx. This object is the same for all configurations. notApplicable - when this object is not supported.
INT prtBertInjectRate	1.3.6.1.4.1.164.3.3.3.1.5.1.3	INTEGER	read-write	This object indicates the error rate injection of the BERT. r10Emx = 10E-x This object is the same for all configurations. single - single error injection. notApplicable - when this object is not supported.
INT prtBertInjectErrRateCmd	1.3.6.1.4.1.164.3.3.3.1.5.1.4	INTEGER	read-write	This object controls activation/deactivation of the Error Rate Injection during BERT.
INT prtBertInjectSingleErrCmd	1.3.6.1.4.1.164.3.3.3.1.5.1.5	INTEGER	read-write	This object enables to initiate a Single Error Injection during BERT (on). Upon completion, the value will automatically change to off(2).
I32 prtBertRunTime	1.3.6.1.4.1.164.3.3.3.1.5.1.6	Integer32	read-only	This object indicates how much time (seconds) passed since BERT started to run.
I32 prtBertESs	1.3.6.1.4.1.164.3.3.3.1.5.1.7	Integer32	read-only	How many Errored Seconds were detected since BERT started to run. Counter for Kmux and MP.
I32 prtBertSyncLoss	1.3.6.1.4.1.164.3.3.3.1.5.1.8	Integer32	read-only	How many times Sync Loss was detected since BERT started to run. For some products: number of seconds in which Sync Loss occured since BERT started to run. See product specification.
I32 prtBertErrorBits	1.3.6.1.4.1.164.3.3.3.1.5.1.9	Integer32	read-only	How many Error Bits were detected since BERT started to run.
INT prtBertClearCounters	1.3.6.1.4.1.164.3.3.3.1.5.1.10	INTEGER	read-write	Setting this object to ON, will enforce a clear operation of some BERT Counters. Upon completion, the value will automatically change to off(2).
INT prtBertSyncStatus	1.3.6.1.4.1.164.3.3.3.1.5.1.11	INTEGER	read-only	Sync Status while BERT runs.
OCT prtBertTs	1.3.6.1.4.1.164.3.3.3.1.5.1.12	OCTET STRING	read-write	This object indicates on which TSs of the selected port, BERT should be applied. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - BERT should be applied on this TS. For a T1 port, the valid raised bits ('1') are: 1..25. For an E1 port, the valid raised bits ('1') are: 1..31. Agents that do not support this feature will send SIZE 0.
STR prtBertResult	1.3.6.1.4.1.164.3.3.3.1.5.1.13	DisplayString	read-only	This object indicates Result of BERT for the selected port (number of error bits divided to the total number of data bits.) Applicable only if BERT is running on this port Agents that do not support this feature will send SIZE 0.
I32 prtBertTxBits	1.3.6.1.4.1.164.3.3.3.1.5.1.14	Integer32	read-only	How many data bits were transmitted since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
I32 prtBertRxBits	1.3.6.1.4.1.164.3.3.3.1.5.1.15	Integer32	read-only	How many data bits were Received since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
I32 prtBertTxErrorBits	1.3.6.1.4.1.164.3.3.3.1.5.1.16	Integer32	read-only	Number of injected error bits since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
prtMonTable	1.3.6.1.4.1.164.3.3.3.1.6		not-accessible	For DXC, the write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch).
prtMonEntry	1.3.6.1.4.1.164.3.3.3.1.6.1		not-accessible	An entry in table.
I32 prtMonCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.6.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. For products that do not support configurations, 1 will be always used.
I32 prtMonitoringIdx	1.3.6.1.4.1.164.3.3.3.1.6.1.2	Integer32	read-only	This object indicates the Monitoring Port Index. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Optimux-T3: 255 (Not Applicable) will be always used. The Monitoring port is always the Station Clock (not considered an interface).
INT prtMonitoringEnable	1.3.6.1.4.1.164.3.3.3.1.6.1.3	INTEGER	read-write	This object indicates if the prtMonitoringIdx is configured as a monitoring port or not. disabled = the port is NOT configured to monitor. Setting this object to this value will cause reset (to 0) of the prtMonitoringTSs and prtMonitoredTSs objects. enabled = the port IS configured to monitor. For Optimux-T3: always enabled (RO supported).
OCT prtMonitoringTSs	1.3.6.1.4.1.164.3.3.3.1.6.1.4	OCTET STRING	read-write	This object indicates which TSs of the Monitoring port, the test equipment should monitor. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled.
I32 prtMonitoredPort	1.3.6.1.4.1.164.3.3.3.1.6.1.5	Integer32	read-write	This object indicates the MONITORED Port Index that the Monitoring port monitors. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * 100 - no port monitored For Optimux-T3: The valid channels are: 0 = no Ch monitored 1..21 or 1..28 (=CH1..CH21 or CH1..CH28) according to product's configuration.
OCT prtMonitoredTSs	1.3.6.1.4.1.164.3.3.3.1.6.1.6	OCTET STRING	read-write	This object indicates which TSs of the Monitored port, should be monitored. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled.
prtCfgParam	1.3.6.1.4.1.164.3.3.3.1.7
prtCfgParamTable	1.3.6.1.4.1.164.3.3.3.1.7.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. KMUX parameters are for the cards: KMBE/New, KVF.6 family.
prtCfgParamEntry	1.3.6.1.4.1.164.3.3.3.1.7.1.1		not-accessible	An entry in table.
I32 prtCfgParamCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.7.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtCfgParamIdx	1.3.6.1.4.1.164.3.3.3.1.7.1.1.2	Integer32	read-only	A unique identifier of the port (within the card when applicable). - For KM-2100: Slot*100+Ch external ports: Ch=1..10 internal ports (sub-channels): Ch=11..20. - For FCD-T1/E1(L): MAIN=111, SUB=113, CH1=122, CH2=124. - For other devices, see specific device's spec.
INT prtCfgParamSlt	1.3.6.1.4.1.164.3.3.3.1.7.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid. notApplicable(255) - for products that do not have Slots.
INT prtCfgParamOperatedMl	1.3.6.1.4.1.164.3.3.3.1.7.1.1.4	INTEGER	read-write	The main link for this channel. The field is relevant only for ML modes of Dual, Priority Bumping and Switched Backup.
INT prtCfgParamMlAtoMlBPrio	1.3.6.1.4.1.164.3.3.3.1.7.1.1.5	INTEGER	read-write	ML-A to ML-B Priority. The field is relevant only for ML modes of Priority Bumping and Switched Backup.
INT prtCfgParamMlBtoMlAPrio	1.3.6.1.4.1.164.3.3.3.1.7.1.1.6	INTEGER	read-write	ML-B to ML-A Priority. The field is relevant only for ML modes of Priority Bumping.
INT prtCfgParamInbandLoopDetection	1.3.6.1.4.1.164.3.3.3.1.7.1.1.7	INTEGER	read-write	Inband Loop Detection. The field is relevant for FCD-T1/E1(L) ports.
INT prtCfgParamInbandLoopPatternCfg	1.3.6.1.4.1.164.3.3.3.1.7.1.1.8	INTEGER	read-write	This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtCfgParamInbandLoopActPattern and prtCfgParamInbandLoopDeactPattern.
STR prtCfgParamInbandLoopActPattern	1.3.6.1.4.1.164.3.3.3.1.7.1.1.9	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtCfgParamInbandLoopPatternCfg=userConfig.
STR prtCfgParamInbandLoopDeactPattern	1.3.6.1.4.1.164.3.3.3.1.7.1.1.10	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtCfgParamInbandLoopPatternCfg=userConfig.
prtT1E1	1.3.6.1.4.1.164.3.3.3.2
prtT1E1StatTable	1.3.6.1.4.1.164.3.3.3.2.1		not-accessible	T1/E1 port statistics table.
prtT1E1StatEntry	1.3.6.1.4.1.164.3.3.3.2.1.1		not-accessible	An entry in the T1/E1 port statistics table.
I32 prtT1E1SPrtIdx	1.3.6.1.4.1.164.3.3.3.2.1.1.1	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 .
INT prtT1E1SSlt	1.3.6.1.4.1.164.3.3.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
G32 prtT1E1OosCount	1.3.6.1.4.1.164.3.3.3.2.1.1.3	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the number of red alarm events since the last count clearing.
G32 prtT1E1BpvLastMin	1.3.6.1.4.1.164.3.3.3.2.1.1.4	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the number of BPV (BiPolar Violation) events detected during the last minute.
G32 prtT1E1BpvMax	1.3.6.1.4.1.164.3.3.3.2.1.1.5	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the maximal number of BPV (BiPolar Violation) events (per minute), detected during the worst minute.
prtT1E1CnfgTable	1.3.6.1.4.1.164.3.3.3.2.2		not-accessible	T1/E1 port configuration table.
prtT1E1CnfgEntry	1.3.6.1.4.1.164.3.3.3.2.2.1		not-accessible	An entry in the T1/E1 port configuration table.
I32 prtT1E1CnfgIdx	1.3.6.1.4.1.164.3.3.3.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
I32 prtT1E1PrtIdx	1.3.6.1.4.1.164.3.3.3.2.2.1.2	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20.
INT prtT1E1Slt	1.3.6.1.4.1.164.3.3.3.2.2.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtT1E1LineType	1.3.6.1.4.1.164.3.3.3.2.2.1.4	INTEGER	read-write	This variable indicates the variety of T1/E1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: esf Extended SuperFrame DS1 d4 AT&T D4 format DS1 - SF e1 CCITT Recommendation G.704 (Table 4a) - G732N e1Crc CCITT Recommendation G.704 (Table 4b) - G732N with CRC e1MF G.704 (Table 4a) with TS16 multiframing enabled - G732S e1CrcMF G.704 (Table 4b) with TS16 multiframing enabled - G732S with CRC unframed T1 - applicable values: (1),(2),(3),(8) E1 - applicable values: (1),(4),(5),(6),(7),(8)
INT prtT1E1LineCode	1.3.6.1.4.1.164.3.3.3.2.2.1.5	INTEGER	read-write	This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. jbzs=b7zs refers the Jammed Bit Zero Suppres- sion, in which the AT&T specification of at least one pulse every 8 bit periods is literal- ly implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data (used for T1). b8zs refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits (used for T1). ANSI Clear Channels may use zbtsi, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use hdb3 or ami (= TRAN). amI (=TRAN) refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
INT prtT1E1SignalMode	1.3.6.1.4.1.164.3.3.3.2.2.1.6	INTEGER	read-write	'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Signaling is in use. 'bitOriented' indicates that E1 Channel Associated Signaling (CAS) is in use. 'messageOriented' indicates that Common Channel Signaling (CCS) is in use either on channel 16 of an E1 link or channel 24 of a T1.
INT prtT1E1Fdl	1.3.6.1.4.1.164.3.3.3.2.2.1.7	INTEGER	read-write	This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following is used. 'ansi-T1-403' refers to the FDL exchange recommended by ANSI. 'att-54016' refers to ESF FDL exchanges. 'fdl-none' indicates that the device does not use the FDL. 'transFdl' indicates transition between two ports of the same card.
INT prtT1E1FdlMode	1.3.6.1.4.1.164.3.3.3.2.2.1.8	INTEGER	read-write	Fdl Mode of the T1 selected port. notApplicable - will be used for an E1 port.
INT prtT1E1Sync	1.3.6.1.4.1.164.3.3.3.2.2.1.9	INTEGER	read-write	This object enables returning to normal operation, after the end of a main/sub link red alarm event, in reduced time. 'tr62411' - complies with AT&T TR-62411 (after 10 seconds). Applicable for both T1 and E1 interfaces. 'ccitt' - complies with CCITT standard. Applicable only for E1 interfaces. 'fast' - after 1 second.
INT prtT1E1CGA	1.3.6.1.4.1.164.3.3.3.2.2.1.10	INTEGER	read-write	This object selects the method used to signal the CGA state to the other end, through the main/sub link. 'none' - non-transparent mode. When one of the links (main/sub) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos Signal' will be transmitted to the other end. 'trans' - when one of the links (main/sub) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main/sub) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos Signal' will be transmitted to the other end.
OCT prtT1E1IdleCode	1.3.6.1.4.1.164.3.3.3.2.2.1.11	OCTET STRING	read-write	This object selects the code transmitted to fill idle (unused) time slots in the main link frame. Valid range: (0 - FF HEX) .
INT prtT1E1OosSignal	1.3.6.1.4.1.164.3.3.3.2.2.1.12	INTEGER	read-write	'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0
OCT prtT1E1VoiceOos	1.3.6.1.4.1.164.3.3.3.2.2.1.13	OCTET STRING	read-write	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT prtT1E1DataOos	1.3.6.1.4.1.164.3.3.3.2.2.1.14	OCTET STRING	read-write	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
INT prtT1E1LineLengthMask	1.3.6.1.4.1.164.3.3.3.2.2.1.15	INTEGER	read-write	This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft 'fcc68' - provides compliance with the FCC 68.308 Option A output pulse mask.
INT prtT1E1TxGainMask	1.3.6.1.4.1.164.3.3.3.2.2.1.16	INTEGER	read-write	This attribute is the tx gain mask parameter (dB), used only for T1/CSU interfaces.
INT prtT1E1InbandMng	1.3.6.1.4.1.164.3.3.3.2.2.1.17	INTEGER	read-write	A unique number to identify an Inband management over the link. internal - supported by KM-2100 only. It means that the management is internal to the frame. It takes part of the ML Frame bits (instead of data).
INT prtT1E1InbandMngRate	1.3.6.1.4.1.164.3.3.3.2.2.1.18	INTEGER	read-write	A unique number to identify the rate of the Inband management. It is required only for E1 links and is applicable only when prtExT1E1InbandMng selected is FdlOrTs0 or dedicatedTs.
I32 prtT1E1DedicatedTs	1.3.6.1.4.1.164.3.3.3.2.2.1.19	Integer32	read-write	The value is differently determined for different products. There are two methods: 1) A unique number to identify Dedicated TS of the T1/E1 port. It is applicable only when prtExT1E1InbandMng selected is dedicatedTs. 1..24 - Dedicated TS of T1 1..31 - Dedicated TS of E1 255 - notApplicable (for agents that do not support this feature) Other values are invalid. 2) For FCD-STM, up to five TSs may be dedicated to management. This object value is the Sum (sigma) of 2n, where n =TS-1 e.g. Time slots 3,5,7,9,11 are dedicated to management: 2 2 +2 4 +2 6 +2 8 +210 = 4+16+64+256+1024=1364 User should consult the product specification, to find out the method employed.
INT prtT1E1InbandMngRoutProt	1.3.6.1.4.1.164.3.3.3.2.2.1.20	INTEGER	read-write	Inband Mng Routing Protocol of the port. When prtT1E1InbandMng is 'dedicatedPpp'-'proprietary' and 'rip2' are applicable. For other values - only 'proprietary' is applicable. For FCD-M and FCD-A: When prtT1E1InbandMng is 'dedicatedPpp' or 'dedicatedFr': 'None', 'proprietary' and 'rip2' are applicable. When prtT1E1InbandMng is 'fdlOrTS0' or 'dedicatedTs': 'None' and 'proprietary' are applicable. When prtT1E1InbandMng is 'off': 'None' is applicable.
INT prtT1E1LinkMode	1.3.6.1.4.1.164.3.3.3.2.2.1.21	INTEGER	read-write	regular - TSs are connected by user via TS Assignment only transparent - when a port with this Link Mode is connected to an internal T1/E1 port of a T3/E3 card, TS0, TS16 and Fbit are transparently transferred to the E3/T3 stream.
INT prtT1E1Multiplier	1.3.6.1.4.1.164.3.3.3.2.2.1.22	INTEGER	read-write	The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps. For T1 only.
INT prtT1E1RxGain	1.3.6.1.4.1.164.3.3.3.2.2.1.23	INTEGER	read-write	This attribute is the rx volume (dB).
INT prtT1E1RAI	1.3.6.1.4.1.164.3.3.3.2.2.1.24	INTEGER	read-write	Remote Alarm Signal
INT prtT1E1LineMode	1.3.6.1.4.1.164.3.3.3.2.2.1.25	INTEGER	read-write	Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values
OCT prtT1E1TS0SaBits	1.3.6.1.4.1.164.3.3.3.2.2.1.26	OCTET STRING	read-write	This object is applicable only for E1 ports. For T1, string size will be 0. For E1, it enables user to select the use of TS0 Sa Bits 4..8, by 3 octets: The order (in hexa display): free Sa-Bit-4 Sa-Bit-5 Sa-Bit-6 Sa-Bit-7 Sa-Bit-8 \|___________\| \|________________\| \|________________\| MSByte LSByte Each Sa Bit will be represented by a nibble, having the following meaning: 0000 = zero 0001 = one 0010 = management 0011 = transparent the rest are reserved for future use.
INT prtT1E1ConnectedTS	1.3.6.1.4.1.164.3.3.3.2.2.1.27	INTEGER	read-only	This parameter indicates if there is any connected TS for this interface.
INT prtT1E1Ts0SaBit	1.3.6.1.4.1.164.3.3.3.2.2.1.28	INTEGER	read-write	This parameter indicates whether to send TS 0, or not. noMng= TS 0 is looped, therefore not sent. mng= TS 0 isn't looped, therefore it is sent.
INT prtT1E1SameFeCnfg	1.3.6.1.4.1.164.3.3.3.2.2.1.29	INTEGER	read-write	This parameter indicates whether the same E1 configuration parameters and TS assignment are set both to the local and remote device. Read-Write access is applicable only in G732N framed mode. For G732S and UNFRAMED this parameter is set by agent to YES and is Read Only. In Case of conflict during power-up between the central and remote, the value set by the central unit is the valid one.
INT prtT1E1RemCrc4	1.3.6.1.4.1.164.3.3.3.2.2.1.30	INTEGER	read-write	This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.
I32 prtT1E1MaxTSs	1.3.6.1.4.1.164.3.3.3.2.2.1.31	Integer32	read-write	This object is applicable only for DXC D4T1, D4E1, D8T1, D8E1 external ports and D8GSL internal E1 ports. It is relevant only when sysCIntTsAllocMode=static(2). 255=not applicable If prtT1E1LineType=unframed(8), the value of this object must be 32. Else, the valid values are 0..31.
INT prtT1E1EocTsConfig	1.3.6.1.4.1.164.3.3.3.2.2.1.32	INTEGER	read-write	This object indicates whether the use of EOC for TS Configuration is enabled or not.
INT prtT1E1Role	1.3.6.1.4.1.164.3.3.3.2.2.1.33	INTEGER	read-write	This object indicates whether this port behaves as SUB or Main link.
INT prtT1E1PppEchoFailDetection	1.3.6.1.4.1.164.3.3.3.2.2.1.34	INTEGER	read-write	This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Disable. Enable - will be selected mainly when a T1/E1 Ring exists and between 2 adjacent Ring devices there is another device or Net, that causes these Ring devices not to sense that the PPP connection between them is lost. In this case, Echo Request should be initiated by the port.
prtT1E1FdlMsgTable	1.3.6.1.4.1.164.3.3.3.2.3		not-accessible	This table is applicable for a T1 interface with 'esf' LineType or E1 interface, when CRC is enabled (LineType).
prtT1E1FdlMsgEntry	1.3.6.1.4.1.164.3.3.3.2.3.1		not-accessible	An entry in table.
I32 prtT1E1FdlMsgPrtIdx	1.3.6.1.4.1.164.3.3.3.2.3.1.1	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 .
INT prtT1E1FdlMsgFdlType	1.3.6.1.4.1.164.3.3.3.2.3.1.2	INTEGER	read-only	The Fdl type reference of the Fdl message.
INT prtT1E1FdlMsgSlt	1.3.6.1.4.1.164.3.3.3.2.3.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
OCT prtT1E1FdlMsg	1.3.6.1.4.1.164.3.3.3.2.3.1.4	OCTET STRING	read-only	FDL message.
prtHS	1.3.6.1.4.1.164.3.3.3.3
prtHSParamTable	1.3.6.1.4.1.164.3.3.3.3.1		not-accessible	A table.
prtHSParamEntry	1.3.6.1.4.1.164.3.3.3.3.1.1		not-accessible	An entry in table.
I32 prtHSCnfgIdx	1.3.6.1.4.1.164.3.3.3.3.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
I32 prtHSPrtIdx	1.3.6.1.4.1.164.3.3.3.3.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT prtHSSlt	1.3.6.1.4.1.164.3.3.3.3.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtHSRate	1.3.6.1.4.1.164.3.3.3.3.1.1.4	INTEGER	read-write	This object indicates the port rate (speed). auto - rate is selected automatically by system.
INT prtHSFifoSize	1.3.6.1.4.1.164.3.3.3.3.1.1.5	INTEGER	read-write	This object selects the size of the user data channel buffer FIFO used in the DTE2 mode. In the other modes, buffer size is automatically set by the DACS agent. Buffer FIFO size in bits, corresponds to FIFO lengths of +/-16, +/-30, +/-52, +/-72 bits.
INT prtHSClkMode	1.3.6.1.4.1.164.3.3.3.3.1.1.6	INTEGER	read-write	Clock Mode of the user data channel. dce - DACS operates as a DCE and provides transmit and receive clocks to the synchronous user DTE. dte1- DACS supplies the receive clock to the user equipment and accepts the user transmit clock. dte2- DACS requires transmit and receive clocks from the user equipment.
INT prtHSCTS	1.3.6.1.4.1.164.3.3.3.3.1.1.7	INTEGER	read-write	Selection of CTS line state in the user data channel. on - CTS continuously ON. rts - CTS line follows the RTS line.
INT prtHSRtsState	1.3.6.1.4.1.164.3.3.3.3.1.1.8	INTEGER	read-only	RTS state of the port.
INT prtHSInbandLoopback	1.3.6.1.4.1.164.3.3.3.3.1.1.9	INTEGER	read-write	This object indicates if Inband Loopback from the Network should be enabled or disabled.
INT prtHSInbandLoopPatternCfg	1.3.6.1.4.1.164.3.3.3.3.1.1.10	INTEGER	read-write	This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtHSActivatePolyPattern and prtHSDeactivatePolyPattern.
STR prtHSInbandLoopActPattern	1.3.6.1.4.1.164.3.3.3.3.1.1.11	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig.
STR prtHSInbandLoopDeactPattern	1.3.6.1.4.1.164.3.3.3.3.1.1.12	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig.
INT prtHSDCD	1.3.6.1.4.1.164.3.3.3.3.1.1.13	INTEGER	read-write	Selection of DCD line state in the user data channel. linkOK - DCD line is ON only when active link is OK. on - DCD continuously ON.
INT prtHSClkPolarity	1.3.6.1.4.1.164.3.3.3.3.1.1.14	INTEGER	read-write	This object indicates the clock polarity.
INT prtHSInterfaceType	1.3.6.1.4.1.164.3.3.3.3.1.1.15	INTEGER	read-write	This object indicates the selected electrical interface type.
INT prtHSUnframed	1.3.6.1.4.1.164.3.3.3.3.1.1.16	INTEGER	read-write	Unframed line for HS ports. yes - means that all TSs must be transferred, including TS0. In this case, prtHSRate must be r31x56eq1736Kbps OR r31x64eq1984Kbps.
prtHSBertTable	1.3.6.1.4.1.164.3.3.3.3.2		not-accessible	A table.
prtHSBertEntry	1.3.6.1.4.1.164.3.3.3.3.2.1		not-accessible	An entry in table.
I32 prtHSBertPrtIdx	1.3.6.1.4.1.164.3.3.3.3.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT prtHSBertSlt	1.3.6.1.4.1.164.3.3.3.3.2.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtHSBertCountClr	1.3.6.1.4.1.164.3.3.3.3.2.1.3	INTEGER	read-write	Setting this object (to on) initiate bert counter clear operation. Valid only when bert test is active on the specific port. (Every time a new bert test starts, the counter is automatically cleared; this command enables clearing the counter while the test is running).
I32 prtHSBertTestResult	1.3.6.1.4.1.164.3.3.3.3.2.1.4	Integer32	read-only	This object indicates the number of Bit Error Rate indicated during the BERT test. Active only when bert test is running on the selected port.
prtSP	1.3.6.1.4.1.164.3.3.3.4
prtSpCnfgTable	1.3.6.1.4.1.164.3.3.3.4.1		not-accessible	A table.
prtSpCnfgEntry	1.3.6.1.4.1.164.3.3.3.4.1.1		not-accessible	All the entries at this table are identical(have the same value) at all the configurations(1..255) except at the TmpCnfg. - For products supporting more than one configuration, the write operation into the Table Objects is valid only at the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table Objects will be to prtSpCnfgIdx=1.
I32 prtSpCnfgIdx	1.3.6.1.4.1.164.3.3.3.4.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
I32 prtSpPrtIdx	1.3.6.1.4.1.164.3.3.3.4.1.1.2	Integer32	read-only	This attribute indicates a unique port number of the SPor DP port. For DXC, it is the port in the active DCL card: - SP = 1 - NP ; DP = 2 For Kilomux, the port index is calculated as follows: 100*Slot+Ch. For FCD, PRBi, the SP port index=1. For Optimux-T3, the SP port index=71.
INT prtSpUsage	1.3.6.1.4.1.164.3.3.3.4.1.1.3	INTEGER	read-write	This attribute indicates what is the usage of the port.
INT prtSpRate	1.3.6.1.4.1.164.3.3.3.4.1.1.4	INTEGER	read-write	This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
INT prtSpDataBits	1.3.6.1.4.1.164.3.3.3.4.1.1.5	INTEGER	read-write	This attribute indicates the number of data bits in async frame
INT prtSpParity	1.3.6.1.4.1.164.3.3.3.4.1.1.6	INTEGER	read-write	This attribute indicates the parity mode in async frame
INT prtSpCallOutMode	1.3.6.1.4.1.164.3.3.3.4.1.1.7	INTEGER	read-write	This attribute indicates the call-out mode. For DXC - this object is applicable only for the DP port (2).
INT prtSpInterface	1.3.6.1.4.1.164.3.3.3.4.1.1.8	INTEGER	read-write	This attribute indicates the supervisory port interface. dce - the DACS appears as a DCE for the port. dte - the DACS operates as a DTE, for connection via modem, for the port.
INT prtSpCTS	1.3.6.1.4.1.164.3.3.3.4.1.1.9	INTEGER	read-write	CTS line state. This object is applicable only for port (1) = SP
INT prtSpDcdDelay	1.3.6.1.4.1.164.3.3.3.4.1.1.10	INTEGER	read-write	DCD delay in msec. d10 = delay of 10msec. This object is applicable only for port (1) = SP
INT prtSpDsr	1.3.6.1.4.1.164.3.3.3.4.1.1.11	INTEGER	read-write	DSR line state. This object is applicable only for port (1) = SP
I32 prtSpNoOfRetries	1.3.6.1.4.1.164.3.3.3.4.1.1.12	Integer32	read-write	For DXC - this object is applicable only for port (2) = DP. The number of dialing retries requested. Default = 0
INT prtSpWaitForConnect	1.3.6.1.4.1.164.3.3.3.4.1.1.13	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. Waiting time for connect, in seconds. Default = 30 sec.
INT prtSpDialMode	1.3.6.1.4.1.164.3.3.3.4.1.1.14	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. Dialing mode. Default=tone
INT prtSpAltNumMode	1.3.6.1.4.1.164.3.3.3.4.1.1.15	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. It determines wether to use the alternate number or not. Default = no.
STR prtSpPrimaryNum	1.3.6.1.4.1.164.3.3.3.4.1.1.16	DisplayString	read-write	For DXC - this object is applicable only for port (2) = DP. It is the Primary dialing number.
STR prtSpAltNum	1.3.6.1.4.1.164.3.3.3.4.1.1.17	DisplayString	read-write	For DXC - this object is applicable only for port (2) = DP. It is the Alternate dialing number. This number is applicable only if prtSpAltNumMode is 'yes'.
INT prtSpRoutProtocol	1.3.6.1.4.1.164.3.3.3.4.1.1.18	INTEGER	read-write	This attribute indicates the routing protocol of the port. notApplicable - for DP.
OCT prtSpCmd	1.3.6.1.4.1.164.3.3.3.4.1.1.19	OCTET STRING	read-write	SP Command. For LRS this parameter will be used for a Modem Command. Upon NMS's Get operation for devices that this parameter is notApplicable, agent will send NULL string.
INT prtSpActCallOut	1.3.6.1.4.1.164.3.3.3.4.1.1.20	INTEGER	read-write	This object indicates when to Activate Call-Out. It is used by FCD-T1/E1. always - to activate call-out always. linkFail - to activate call-out only when Link of Inband Management fails.
INT prtSpAlrRelayMode	1.3.6.1.4.1.164.3.3.3.4.1.1.21	INTEGER	read-write	This attribute indicates the Alarm Relay Mode. notApplicable - for DP.
INT prtSpStopBits	1.3.6.1.4.1.164.3.3.3.4.1.1.22	INTEGER	read-write	This attribute indicates number of stop bits in an async frame.
prtDim	1.3.6.1.4.1.164.3.3.3.5
prtDimCnfgTable	1.3.6.1.4.1.164.3.3.3.5.1		not-accessible	A table.
prtDimCnfgEntry	1.3.6.1.4.1.164.3.3.3.5.1.1		not-accessible	The write operation into the Table Objects is valid only for the TmpCnfg entry (prtDimCnfgIdx=255).
I32 prtDimCnfgIdx	1.3.6.1.4.1.164.3.3.3.5.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
I32 prtDimIdx	1.3.6.1.4.1.164.3.3.3.5.1.1.2	Integer32	read-only	This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10)*10 + 1 Example: port1 of IO slot 11 will be: 211 .
INT prtDimTxMode	1.3.6.1.4.1.164.3.3.3.5.1.1.3	INTEGER	read-write	Tx mode. regularTx - the links are connected to a similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is decreased accordingly. broadcast - the links are connected to MORE than one similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is not affected
INT prtDimPolarity	1.3.6.1.4.1.164.3.3.3.5.1.1.4	INTEGER	read-write	Polarity.
INT prtDimClkMode	1.3.6.1.4.1.164.3.3.3.5.1.1.5	INTEGER	read-write	Clock Mode. smooth - a clock that is not 'pulsed'(has no 'gaps'). In this mode the DXC does NOT receive back the clock signal. extSmooth - same as 'smooth' but in this mode, the DXC receives back the clock signal.
INT prtDimMaxDelay	1.3.6.1.4.1.164.3.3.3.5.1.1.6	INTEGER	read-write	Max Delay permitted between the links, in msec.
INT prtDimMng	1.3.6.1.4.1.164.3.3.3.5.1.1.7	INTEGER	read-write	Use of DIM port for management. disabled - no management on DIM ts1 - 1 bit of TS1 is used for management.
INT prtDimMngRoutProt	1.3.6.1.4.1.164.3.3.3.5.1.1.8	INTEGER	read-write	Mng Routing Protocol of the port. none - when prtDimMng is 'disabled'.
prtDimDestTable	1.3.6.1.4.1.164.3.3.3.5.2		not-accessible	A table.
prtDimDestEntry	1.3.6.1.4.1.164.3.3.3.5.2.1		not-accessible	The write operation is valid only for the TmpCnfg entry (prtDimDestCnfgIdx=255).
I32 prtDestCnfgIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
I32 prtDestDimIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.2	Integer32	read-only	This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10) & 1 Example: port1 of IO slot 11 will be: 211 .
I32 prtDestIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.3	Integer32	read-only	This attribute indicates a destination number of the DIM card.
I32 prtDest	1.3.6.1.4.1.164.3.3.3.5.2.1.4	Integer32	read-write	Destination port,(of a T1/E1 port), that is connected to the DIM card, for the specified Destination number. 0 = No destination port. Else: For external ports: (IO Slot+10) & 1 for port 1 (IO Slot+10) & 3 for port 2 Example: port2 of IO slot 12 will be: 223 . For internal ports : (IO Slot+10) & 2 for port 1 (IO Slot+10) & 4 for port 2 (IO Slot+10) & 6 for port 3 (IO Slot+10) & 8 for port 4, etc...
INT prtDestConnect	1.3.6.1.4.1.164.3.3.3.5.2.1.5	INTEGER	read-only	Connection Status of the specified destination number. For a specified destination port, it depends both on the status of the port and on the status of the far-end port. Since this is a RO object, same value will be received for all configurations.
prtI	1.3.6.1.4.1.164.3.3.3.6
prtICnfgTable	1.3.6.1.4.1.164.3.3.3.6.1		not-accessible	A table.
prtICnfgEntry	1.3.6.1.4.1.164.3.3.3.6.1.1		not-accessible	An entry in table.
I32 prtICnfgIdx	1.3.6.1.4.1.164.3.3.3.6.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
I32 prtIIdx	1.3.6.1.4.1.164.3.3.3.6.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The ISDN B1, B2, D channels will be inside ports. For port index, see product specification.
INT prtIRate	1.3.6.1.4.1.164.3.3.3.6.1.1.3	INTEGER	read-write	This object indicates the port rate in bits. Each TS contains 8 bits. Thus, 1 bit is equivalent to 8Kbps rate.
INT prtIConnect	1.3.6.1.4.1.164.3.3.3.6.1.1.4	INTEGER	read-write	D channel connection. no - disconnected yes - connected.
prtHdsl	1.3.6.1.4.1.164.3.3.3.7
prtHdslTable	1.3.6.1.4.1.164.3.3.3.7.1		not-accessible	HDSL port table.
prtHdslEntry	1.3.6.1.4.1.164.3.3.3.7.1.1		not-accessible	An entry in table.
I32 prtHdslIdx	1.3.6.1.4.1.164.3.3.3.7.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The HDSL ports will be external. For port index, see product specification.
INT prtHdslMode	1.3.6.1.4.1.164.3.3.3.7.1.1.2	INTEGER	read-write	This object indicates the HDSL mode.
INT prtHdslRptrType	1.3.6.1.4.1.164.3.3.3.7.1.1.3	INTEGER	read-only	The Repeater between Near and Far modem. none - no repeater exists between the modems hrpt - HRPT repeater exists between the modems.
INT prtHdslMaxRate	1.3.6.1.4.1.164.3.3.3.7.1.1.4	INTEGER	read-write	Maximum Rate of the xDSL Line, in Kbps units. This object can be Set only for a Central unit.
INT prtHdslLinkType	1.3.6.1.4.1.164.3.3.3.7.1.1.5	INTEGER	read-only	The Link Type. msdsl2w - MSDSL 2 Wire hdsl2w - HDSL 2 Wire hdsl4w - HDSL 4 Wire gDsl - G.DSL
STR prtHdslCompSwVer	1.3.6.1.4.1.164.3.3.3.7.1.1.6	DisplayString	read-only	This object indicates the Software Version of the component (Piggyback card) supporting this interface.
STR prtHdslCompHwVer	1.3.6.1.4.1.164.3.3.3.7.1.1.7	DisplayString	read-only	This object indicates the Hardware Version of the component (Piggyback card) supporting this interface.
prtT3E3	1.3.6.1.4.1.164.3.3.3.8
prtT3E3CnfgTable	1.3.6.1.4.1.164.3.3.3.8.1		not-accessible	T3/E3 port configuration table.
prtT3E3CnfgEntry	1.3.6.1.4.1.164.3.3.3.8.1.1		not-accessible	An entry in the T3/E3 port configuration table.
I32 prtT3E3CnfgIdx	1.3.6.1.4.1.164.3.3.3.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For DXC, write operations can be performed only on the Temp Config. For products that do not support configurations, always 1 will be used.
I32 prtT3E3PrtIdx	1.3.6.1.4.1.164.3.3.3.8.1.1.2	Integer32	read-only	This attribute indicates a unique port number. For DXC: The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The external ports convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For Optimux-T3: Link-A: 51 Link-B: 61 .
INT prtT3E3Slt	1.3.6.1.4.1.164.3.3.3.8.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtT3E3LineLength	1.3.6.1.4.1.164.3.3.3.8.1.1.4	INTEGER	read-write	This object is the length of the ds3 line in feet. It provides information for line build out circuitry if it exists and can use this object to adjust the line build out. len0p450ft = 0 - 450 feet len451p900ft = 451 - 900 feet.
INT prtT3E3InbandMng	1.3.6.1.4.1.164.3.3.3.8.1.1.5	INTEGER	read-write	A unique number to identify the Frame Type over the link. For Optimux-T3: only values (4), (7) are supported.
INT prtT3E3AisFrame	1.3.6.1.4.1.164.3.3.3.8.1.1.6	INTEGER	read-write	This object is applicable only for Optimux-T3. It allows user to select whether the AIS sent will be framed or unframed.
INT prtT3E3TxClockSource	1.3.6.1.4.1.164.3.3.3.8.1.1.7	INTEGER	read-write	Tx Clock Source.
INT prtT3E3RoutProt	1.3.6.1.4.1.164.3.3.3.8.1.1.8	INTEGER	read-write	Routing Protocol of the port. This object is applicable only for T3 ports.
INT prtT3E3AisTransmit	1.3.6.1.4.1.164.3.3.3.8.1.1.9	INTEGER	read-write	Indicates if AIS signal will be transmitted over the tributary E3/DS3 upon failure.
genDacsMux	1.3.6.1.4.1.164.3.3.4
cmprTable	1.3.6.1.4.1.164.3.3.4.1		not-accessible	A table.
cmprEntry	1.3.6.1.4.1.164.3.3.4.1.1		not-accessible	An entry in table.
I32 cmprTypeIdx	1.3.6.1.4.1.164.3.3.4.1.1.1	Integer32	read-only	This object indicates the Type of the Compressed data referred (which table, which level, etc). The type is a code according to a convention between agent and NMS.
I32 cmprCnfgIdx	1.3.6.1.4.1.164.3.3.4.1.1.2	Integer32	read-only	This object indicates the configuration number the Compressed information relates to.
I32 cmprVersion	1.3.6.1.4.1.164.3.3.4.1.1.3	Integer32	read-only	This object indicates the version of the internal format of the Compressed data (the version of the convention used).
INT cmprSltIdx	1.3.6.1.4.1.164.3.3.4.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. When the unit is stand-alone or this object is not applicable, 255 will be used.
I32 cmprPrtIdx	1.3.6.1.4.1.164.3.3.4.1.1.5	Integer32	read-only	This object indicates a unique identifier of the port, the compressed information relates to. For DXC - according to the order in the card of cmprSltIdx: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For FCD: see product's specification. If the port number is irrelevant to this parameter (if it is a system/card level alarm) the value will be 9999.
OCT cmprObj	1.3.6.1.4.1.164.3.3.4.1.1.6	OCTET STRING	read-write	This object is the compressed information itself, according to a predefined format, both agent and NMS agreed about.
mapLinkTable	1.3.6.1.4.1.164.3.3.4.2		not-accessible	A table.
mapLinkEntry	1.3.6.1.4.1.164.3.3.4.2.1		not-accessible	An entry in table.
I32 mapLinkIdx	1.3.6.1.4.1.164.3.3.4.2.1.1	Integer32	read-only	A unique identifier of the link
INT mapLinkSlotIdx	1.3.6.1.4.1.164.3.3.4.2.1.2	INTEGER	read-write	This attribute indicates a unique slot position where the module is inserted.
I32 mapLinkPortIdx	1.3.6.1.4.1.164.3.3.4.2.1.3	Integer32	read-write	This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
INT mapLinkState	1.3.6.1.4.1.164.3.3.4.2.1.4	INTEGER	read-only	This attribute indicates the status of the link between the two muxes
alrGenTable	1.3.6.1.4.1.164.3.3.4.3		not-accessible	A table.
alrGenEntry	1.3.6.1.4.1.164.3.3.4.3.1		not-accessible	An entry in table.
I32 alrGenCode	1.3.6.1.4.1.164.3.3.4.3.1.1	Integer32	read-only	This object is a unique code number, identifying a certain alarm.
STR alrGenDescription	1.3.6.1.4.1.164.3.3.4.3.1.2	DisplayString	read-only	This entry is a unique text description, of the alarm corresponding to the specified code.
INT alrGenLevel	1.3.6.1.4.1.164.3.3.4.3.1.3	INTEGER	read-only	Alarm level.
INT alrGenSlotType	1.3.6.1.4.1.164.3.3.4.3.1.4	INTEGER	read-only	Slot type that the alarm is relevant to. clAndIo - an alarm that is relevant for both CL and IO slots.
INT alrGenSeverity	1.3.6.1.4.1.164.3.3.4.3.1.5	INTEGER	read-write	This object enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code).
I32 alrGenDebounce	1.3.6.1.4.1.164.3.3.4.3.1.6	Integer32	read-write	Debounce time for each alarm code, in seconds. The meaning is, that an alarm will be 'declared' as ON (or OFF), only after it was actually ON/OFF the Debouncing time selected by user. 0 = default debounce selection (each alarm has a default value). 250 = maximum value of seconds for debounce. 253 = mask = the alarm will Never be reported. 254 = default debounce selection (each alarm has a default value). 255 = not applicable
INT alrGenDefSeverity	1.3.6.1.4.1.164.3.3.4.3.1.7	INTEGER	read-only	This object reports the default severity of each alarm. User can change the severity of the alarms defined by this default via the alrGenSeverity object.
radBridges	1.3.6.1.4.1.164.4
genBridge	1.3.6.1.4.1.164.4.1
INT radBridgeAction	1.3.6.1.4.1.164.4.1.1	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the tables maintained by the network device. Send actions are not currently implemented. Not all actions can be performed on all bridges.
I32 radBridgeInactiveArpTimeOut	1.3.6.1.4.1.164.4.1.2	Integer32	read-write	This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
radBridgeMaskTable	1.3.6.1.4.1.164.4.1.3		not-accessible	Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement consisting of up to three mask definitions and an action defined by radBridgeMaskOper. Different types of mask entries are supported, as defined by radBridgeMaskType.
radBridgeMaskEntry	1.3.6.1.4.1.164.4.1.3.1		not-accessible	An entry in table radBridgeMaskTable.
INT radBridgeMaskType	1.3.6.1.4.1.164.4.1.3.1.1	INTEGER	read-only	Defines the type of mask entry.
I32 radBridgeMaskIfIndex	1.3.6.1.4.1.164.4.1.3.1.2	Integer32	read-only	Specifies the if Index of the interface to which the mask is applied.
I32 radBridgeMaskNum	1.3.6.1.4.1.164.4.1.3.1.3	Integer32	read-only	The Mask entry number, defined by its line number in the mask table.
INT radBridgeMaskDest	1.3.6.1.4.1.164.4.1.3.1.4	INTEGER	read-write	Specifies the type of destination address carried by the frame to which the mask will be applied. Unassigned-condition deactivates the mask entry.
OCT radBridgeMaskPat1	1.3.6.1.4.1.164.4.1.3.1.5	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
OCT radBridgeMaskActiveBit1	1.3.6.1.4.1.164.4.1.3.1.6	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat1 field.
INT radBridgeMaskFrom1	1.3.6.1.4.1.164.4.1.3.1.7	INTEGER	read-write	Offset base of radBridgeMaskPat1 within the frame. Net can be in some cases the data start point.
I32 radBridgeMaskOffset1	1.3.6.1.4.1.164.4.1.3.1.8	Integer32	read-write	Specifies the radBridgeMaskPat1 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm1.The mask offset is an even decimal number in the range of 0 to 1518.
INT radBridgeMaskCond1	1.3.6.1.4.1.164.4.1.3.1.9	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that matches the content of radBridgeMaskPat1. false - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that does not match the content of radBridgeMaskPat1.
OCT radBridgeMaskPat2	1.3.6.1.4.1.164.4.1.3.1.10	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
OCT radBridgeMaskActiveBit2	1.3.6.1.4.1.164.4.1.3.1.11	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat2 field.
INT radBridgeMaskFrom2	1.3.6.1.4.1.164.4.1.3.1.12	INTEGER	read-write	Offset base of radBridgeMaskPat2 within the frame. Net can be in some cases the data start point.
I32 radBridgeMaskOffset2	1.3.6.1.4.1.164.4.1.3.1.13	Integer32	read-write	Specifies the radBridgeMaskPat2 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm2.The mask offset is an even decimal number in the range of 0 to 1518.
INT radBridgeMaskCond2	1.3.6.1.4.1.164.4.1.3.1.14	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that matches the content of radBridgeMaskPat2. false - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that does not match the content of radBridgeMaskPat2.
OCT radBridgeMaskPat3	1.3.6.1.4.1.164.4.1.3.1.15	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
OCT radBridgeMaskActiveBit3	1.3.6.1.4.1.164.4.1.3.1.16	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat3 field.
INT radBridgeMaskFrom3	1.3.6.1.4.1.164.4.1.3.1.17	INTEGER	read-write	Offset base of radBridgeMaskPat3 within the frame. Net can be in some cases the data start point.
I32 radBridgeMaskOffset3	1.3.6.1.4.1.164.4.1.3.1.18	Integer32	read-write	Specifies the radBridgeMaskPat3 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm3. The mask offset is an even decimal number in the range of 0 to 1518.
INT radBridgeMaskCond3	1.3.6.1.4.1.164.4.1.3.1.19	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that matches the content of radBridgeMaskPat3 false - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that does not match the content of radBridgeMaskPat3.
INT radBridgeMaskOper	1.3.6.1.4.1.164.4.1.3.1.20	INTEGER	read-write	The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list.
radBridgeCOD	1.3.6.1.4.1.164.4.1.4
radBridgeCODParamTable	1.3.6.1.4.1.164.4.1.4.1		not-accessible	The table of COD parameters
radBridgeCODEntry	1.3.6.1.4.1.164.4.1.4.1.1		not-accessible	Each radBridgeCODEntry consists of the following parameters
I32 radBridgeCODIfIndex	1.3.6.1.4.1.164.4.1.4.1.1.1	Integer32	read-only	The interface to which this COD entry is applicable.
INT radBridgeCODManualConnect	1.3.6.1.4.1.164.4.1.4.1.1.2	INTEGER	read-write	The management station can start connection manually by setting this parameter
INT radBridgeCODMode	1.3.6.1.4.1.164.4.1.4.1.1.3	INTEGER	read-write	In answer mode only one incoming call may be accepted at a time. Other nodes attempting to access the local modem will receive a busy signal until the connection is terminated. (Answer mode has no difficulty supporting multiple remote connections to one local port, as blocking multiple incoming calls is just a modem function. Originate mode, on the other hand will only support a single local port to remote port connection). The disable parameter disables the COD utility for this interface. Choosing any other mode will enable the COD utility.
I32 radBridgeCODConnectDelay	1.3.6.1.4.1.164.4.1.4.1.1.4	Integer32	read-write	The connect delay defines the minimum time period that the link must stay disconnected, between 2 succesive connections (in seconds).
I32 radBridgeCODisConnectDelay	1.3.6.1.4.1.164.4.1.4.1.1.5	Integer32	read-write	The disconnect delay defines the minimum time period the link must stay connected, between 2 succesive disconnections (in seconds).
INT radBridgeCODImplicitSwitch	1.3.6.1.4.1.164.4.1.4.1.1.6	INTEGER	read-write	The inplicit switch allows the user to ignore implicit triggers provided by the COD software.
C32 radBridgeCODNumAccess	1.3.6.1.4.1.164.4.1.4.1.1.7	Counter32	read-only	The number of successful connections that have been established since the COD has been reset.
I32 radBridgeCODTotalConnecTime	1.3.6.1.4.1.164.4.1.4.1.1.8	Integer32	read-only	The sum of all the connect time intervals since the COD was reset.
radBridgeCODTimeTriggerTable	1.3.6.1.4.1.164.4.1.4.2		not-accessible	The table of COD parameters
radBridgeCODTimeTriggerEntry	1.3.6.1.4.1.164.4.1.4.2.1		not-accessible	Each radBridgeCODTimeTriggerEntry consists of the following parameters
I32 radBridgeCODTimeIfIndex	1.3.6.1.4.1.164.4.1.4.2.1.1	Integer32	read-only	The interface to which this COD Time Trigger entry is applicable.
INT radBridgeCODDay	1.3.6.1.4.1.164.4.1.4.2.1.2	INTEGER	read-only	The day of the week in which the dial up connection operates.
I32 radBridgeCODTimeTriggerNum	1.3.6.1.4.1.164.4.1.4.2.1.3	Integer32	read-only	Every day of the week the user can configure 3 dial up connections.
STR radBridgeCODTimeTriggerFrom	1.3.6.1.4.1.164.4.1.4.2.1.4	DisplayString	read-write	Time to start Dial Up connection, in format hh:mm.
STR radBridgeCODTimeTriggerTo	1.3.6.1.4.1.164.4.1.4.2.1.5	DisplayString	read-write	Time to terminate Dial Up connection, in format HH:MM.
INT radBridgeCODTimeTriggerStatus	1.3.6.1.4.1.164.4.1.4.2.1.6	INTEGER	read-write	The status of a table entry.
radBridgeCODTraffic	1.3.6.1.4.1.164.4.1.4.3
radBridgeCODTrafficTable	1.3.6.1.4.1.164.4.1.4.3.1		not-accessible	The table of COD Traffic trigger
radBridgeCODTrafficEntry	1.3.6.1.4.1.164.4.1.4.3.1.1		not-accessible	Each radBridgeCODTrafficEntry consists of the following parameters.
INT radBridgeCODProtocolType	1.3.6.1.4.1.164.4.1.4.3.1.1.1	INTEGER	read-only	The Protocol Type of the Traffic Table
INT radBridgeCODTrafficTriggerStatus	1.3.6.1.4.1.164.4.1.4.3.1.1.2	INTEGER	read-write	Command of Status of the Protocol Traffic Trigger
IP radBridgeCODRemoteIPAddr	1.3.6.1.4.1.164.4.1.4.3.2	IpAddress	read-write	This is the Remote IP Address
IP radBridgeCODIPMask	1.3.6.1.4.1.164.4.1.4.3.3	IpAddress	read-write	This is the Mask of the Remote IP Address
OCT radBridgeCODTrafficTriggerProtType	1.3.6.1.4.1.164.4.1.4.3.4	OCTET STRING	read-write	Protocol Type for the User Defined Protocol Traffic Trigger (3).
radBridgeCODCondTable	1.3.6.1.4.1.164.4.1.4.4		not-accessible	The table of COD Condition parameters
radBridgeCODCondEntry	1.3.6.1.4.1.164.4.1.4.4.1		not-accessible	Each radBridgeCODCondEntry consists of the following parameters
I32 radBridgeCODCondIfIndex	1.3.6.1.4.1.164.4.1.4.4.1.1	Integer32	read-only	The interface, this COD entry is applicable to.
INT radBridgeCODOriginateConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.2	INTEGER	read-write	This condition, allows the user to specify the condition under which the link is connected. The options are onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=connect).
INT radBridgeCODOriginateDisConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.3	INTEGER	read-write	This condition allows the user to specify the condition under which the link is disconnected. The options are: noStationOnLan - When there is no station on lan. Counts 15 minutes from the point the last frame from lan has been received. If no frame have been transmitted on lan by the end of this period, disconnect the connection. onTraffic - On traffic. The user can specify the condition/s for disconnection. The disconnection will be defined in CODSpecificOnTrafficConditionOID . onDelayFromConnectionOnRequest - On Delay From Connection On Request . The delay time period will be defined in CODOriginateDisConnectDelay . onManualDisConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=disconnect).
I32 radBridgeCODOriginateDisConnectDelay	1.3.6.1.4.1.164.4.1.4.4.1.4	Integer32	read-write	Delay time in seconds.
INT radBridgeCODAnswerConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.5	INTEGER	read-write	CODCondAnswerConnect allows the user to specify the condition under which the link is connected. The options are: onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE .
OID radBridgeCODSpecificOnTrafficOIDCondition	1.3.6.1.4.1.164.4.1.4.4.1.6	OBJECT IDENTIFIER	read-only	A reference to a specific entry in the radBridgeMaskTable, which describes the particular COD condition . If Connect or Disconnect Conditions are not onTraffic, its value should be set to the OBJECT IDENTIFIER { 0 0 }.
I32 radBridgeCODDisConnectMinimunFramesNumber	1.3.6.1.4.1.164.4.1.4.4.1.7	Integer32	read-write	Frames rate.
radBridgeIPX	1.3.6.1.4.1.164.4.1.5
radBridgeIPXdriver	1.3.6.1.4.1.164.4.1.5.1
INT radBridgeIPXForwarding	1.3.6.1.4.1.164.4.1.5.1.1	INTEGER	read-write	The indication of whether this entity is acting as an IPX gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IPX gateways forward datagrams. IPX hosts do not. Note that changing this parameter requiers RESET of the router.
radBridgeIPXRip	1.3.6.1.4.1.164.4.1.5.2
C32 radBridgeIPXRipOutPackets	1.3.6.1.4.1.164.4.1.5.2.1	Counter32	read-only	The total number of packets transmitted by RIP.
C32 radBridgeIPXRipInPackets	1.3.6.1.4.1.164.4.1.5.2.2	Counter32	read-only	The total number of packets received by RIP. This will include any packets that are subsequently discarded.
C32 radBridgeIPXRipInDiscards	1.3.6.1.4.1.164.4.1.5.2.3	Counter32	read-only	The number of received packets discarded by RIP.
I32 radBridgeIPXRipTblNoOfEntries	1.3.6.1.4.1.164.4.1.5.2.4	Integer32	read-only	The max number of entries that exist in the RIP routing table.
I32 radBridgeIPXRipTblBcastTrigUpdateInterval	1.3.6.1.4.1.164.4.1.5.2.5	Integer32	read-write	The default time interval (in seconds)between triggered RIP updates on a broadcast type interface. A triggered update occurs when a change is detected in the routing database. This time interval delays the broadcasting of these updates so that changes on the network will not result in a lot of triggered updates.
radBridgeIPXRipTable	1.3.6.1.4.1.164.4.1.5.2.6		not-accessible	The routing table used by RIP to calculate routes to remote desination networks.
radBridgeIPXRipTableEntry	1.3.6.1.4.1.164.4.1.5.2.6.1		not-accessible	The routing information for one of this entity's destination networks.
OCT radBridgeIPXRipDestNetwork	1.3.6.1.4.1.164.4.1.5.2.6.1.1	OCTET STRING	read-only	The destination network address to which this entry's routing information pertains.
INT radBridgeIPXRipPolicy	1.3.6.1.4.1.164.4.1.5.2.6.1.2	INTEGER	read-only	A value specifying the precidence of the route. A value of zero means that the route is the best route, a value of one means that the route is the second best route and so on.
OCT radBridgeIPXRipForwardingRouter	1.3.6.1.4.1.164.4.1.5.2.6.1.3	OCTET STRING	read-write	The IPX node address of the next hop (router) for the entry's associated destination network.
I32 radBridgeIPXRipNIC	1.3.6.1.4.1.164.4.1.5.2.6.1.4	Integer32	read-write	An interface identifier specifying what IPX interface the next hop can be found on.
I32 radBridgeIPXRipTickMetric	1.3.6.1.4.1.164.4.1.5.2.6.1.5	Integer32	read-write	The metric, in terms of transit time, associated with the route given by the entry. This time is in terms of 1/18ths of a second.
I32 radBridgeIPXRipHopMetric	1.3.6.1.4.1.164.4.1.5.2.6.1.6	Integer32	read-write	The metric, in terms of distance , associated with the route given by the entry.
TIK radBridgeIPXRipAgingTime	1.3.6.1.4.1.164.4.1.5.2.6.1.7	TimeTicks	read-only	The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.
INT radBridgeIPXRipValueStatus	1.3.6.1.4.1.164.4.1.5.2.6.1.8	INTEGER	read-write	The entry status value; whether the entry is permanent (added statically), reachable or unreachable. In the latter two cases it would be added by RIP. A semiDynamic entry is an entry enterd manualy by the user and can be updated by the router.
INT radBridgeIPXRipForwardType	1.3.6.1.4.1.164.4.1.5.2.6.1.9	INTEGER	read-write	The type of route. Note that local(2) refers to a route for which the next hop is the final destination; remote(3) refers to a route for which the next hop is not the final destination.
radBridgeIPXRipInfTable	1.3.6.1.4.1.164.4.1.5.2.7		not-accessible	The RIP interface table.
radBridgeIPXRipInfEntry	1.3.6.1.4.1.164.4.1.5.2.7.1		not-accessible	Each entry corresponds to one ifindex.
I32 radBridgeIPXRipInfIfIndex	1.3.6.1.4.1.164.4.1.5.2.7.1.1	Integer32	read-only	This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.
I32 radBridgeIPXRipInfBcastUpdate	1.3.6.1.4.1.164.4.1.5.2.7.1.2	Integer32	read-write	The RIP periodic update interval, in seconds. Zero value corresponds to infinite interval.
I32 radBridgeIPXRipInfAgeMultiplier	1.3.6.1.4.1.164.4.1.5.2.7.1.3	Integer32	read-write	The holding multiplier for information received in RIP periodic updates. Zero value corresponds to infinite aging time.
radBridgeIPXSap	1.3.6.1.4.1.164.4.1.5.3
C32 radBridgeIPXSapOutPackets	1.3.6.1.4.1.164.4.1.5.3.1	Counter32	read-only	The total number of packets transmitted by SAP.
C32 radBridgeIPXSapInPackets	1.3.6.1.4.1.164.4.1.5.3.2	Counter32	read-only	The total number of packets received by SAP. This will include any packets that are subsequently discarded.
C32 radBridgeIPXSapInDiscards	1.3.6.1.4.1.164.4.1.5.3.3	Counter32	read-only	The number of received packets discarded by SAP.
I32 radBridgeIPXSapTblNoOfEntries	1.3.6.1.4.1.164.4.1.5.3.4	Integer32	read-only	The max number of entries that exist in the SAP Server Information table.
I32 radBridgeIPXSapTblBcastTrigUpdateInterval	1.3.6.1.4.1.164.4.1.5.3.5	Integer32	read-write	The default time interval (in seconds) between triggered SAP updates on a broadcast style interface. A triggered update occurs when a change is detected in the service database. This time interval delays the transmission of these updates so that changes on the network will not result in a lot of triggered updates.
radBridgeIPXSapTable	1.3.6.1.4.1.164.4.1.5.3.6		not-accessible	The Server Information table is used by SAP to store information of services which are available on the internetwork.
radBridgeIPXSapTableEntry	1.3.6.1.4.1.164.4.1.5.3.6.1		not-accessible	The server information for one of this entity's server entries.
I32 radBridgeIPXSapServerType	1.3.6.1.4.1.164.4.1.5.3.6.1.1	Integer32	read-only	The type of the server for which this entry pertains.
STR radBridgeIPXSapName	1.3.6.1.4.1.164.4.1.5.3.6.1.2	DisplayString	read-only	The name of the server for which this entry pertains.
OCT radBridgeIPXSapNetwork	1.3.6.1.4.1.164.4.1.5.3.6.1.3	OCTET STRING	read-write	The IPX network address of the host on which this server exists.
OCT radBridgeIPXSapNode	1.3.6.1.4.1.164.4.1.5.3.6.1.4	OCTET STRING	read-write	The IPX node address of the host on which this server exists.
I32 radBridgeIPXSapSocket	1.3.6.1.4.1.164.4.1.5.3.6.1.5	Integer32	read-write	The IPX socket number that is being used by the server to which this entry pertains.
I32 radBridgeIPXSapHopsToServer	1.3.6.1.4.1.164.4.1.5.3.6.1.6	Integer32	read-write	The number of hops to the entity on which this server exists.
I32 radBridgeIPXSapNIC	1.3.6.1.4.1.164.4.1.5.3.6.1.7	Integer32	read-write	An Network Interface Card identifier specifying what IPX interface the next hop can be found on.
TIK radBridgeIPXSapAgingTime	1.3.6.1.4.1.164.4.1.5.3.6.1.8	TimeTicks	read-only	The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.
INT radBridgeIPXSapStatus	1.3.6.1.4.1.164.4.1.5.3.6.1.9	INTEGER	read-write	The status of the entry.
radBridgeIPXSapInfTable	1.3.6.1.4.1.164.4.1.5.3.7		not-accessible	The Sap interface table.
radBridgeIPXSapInfEntry	1.3.6.1.4.1.164.4.1.5.3.7.1		not-accessible	Each entry corresponds to one ifindex.
I32 radBridgeIPXSapInfIfIndex	1.3.6.1.4.1.164.4.1.5.3.7.1.1	Integer32	read-only	This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.
I32 radBridgeIPXSapInfBcastUpdate	1.3.6.1.4.1.164.4.1.5.3.7.1.2	Integer32	read-write	The SAP periodic update interval, in seconds. Zero value corresponds to infinite interval.
I32 radBridgeIPXSapInfAgeMultiplier	1.3.6.1.4.1.164.4.1.5.3.7.1.3	Integer32	read-write	The holding multiplier for information received in SAP periodic updates. Zero value corresponds to infinite aging time.
newMasking	1.3.6.1.4.1.164.4.1.6
I32 maskingMaxEntries	1.3.6.1.4.1.164.4.1.6.1	Integer32	read-only	The maximum number of entries in the masking table.
I32 maskingCurrentEntries	1.3.6.1.4.1.164.4.1.6.2	Integer32	read-only	The number of entries in the mask table.
maskingTable	1.3.6.1.4.1.164.4.1.6.3		not-accessible	This is the new masking scheme. Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement and an action defined by maskingOperation.
maskingEntry	1.3.6.1.4.1.164.4.1.6.3.1		not-accessible	Defines the contents of each line in the mask table.
INT maskingType	1.3.6.1.4.1.164.4.1.6.3.1.1	INTEGER	read-only	Defines the type of mask entry.
I32 maskingIfIndex	1.3.6.1.4.1.164.4.1.6.3.1.2	Integer32	read-only	Specifies the ifIndex of the interface to which the mask is applied.
I32 maskingIndex	1.3.6.1.4.1.164.4.1.6.3.1.3	Integer32	read-only	An index to the masking table. This number should not be greater than maskingMaxEntries
INT maskingProtocolType	1.3.6.1.4.1.164.4.1.6.3.1.4	INTEGER	read-write	The base protocol for masking. IPX, IP, others.
OID maskingSmartMaskOID	1.3.6.1.4.1.164.4.1.6.3.1.5	OBJECT IDENTIFIER	read-only	A reference to a specific Smart mask table (old radBridgeMaskTable) which enables a more specific mask type. If this information is not available, its value should be set to the OBJECT IDENTIFIER { 0 0 }.
INT maskingFrameType	1.3.6.1.4.1.164.4.1.6.3.1.6	INTEGER	read-write	Enables the user to decide about frame type * all frame * just broadcast * just multicast.
INT maskingFrameTypeCondition	1.3.6.1.4.1.164.4.1.6.3.1.7	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingFrameType the packet contains data that matches the content of maskingFrameType. fa lse - Condition is valid if at the position specified by maskingFrameType the packet contains data that does not match the content of maskingFrameType.
ADR maskingSourceAddress	1.3.6.1.4.1.164.4.1.6.3.1.8	GenAddress	read-write	The source address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles).
ADR maskingSourceActiveBits	1.3.6.1.4.1.164.4.1.6.3.1.9	GenAddress	read-write	Specifies the positions of the wild card characters (*) in the maskingSourceAddress field. Only the 1's bit will be taken in considerations.
INT maskingSourceMacOrNet	1.3.6.1.4.1.164.4.1.6.3.1.10	INTEGER	read-write	The variable maskingSourceAddress and maskingSourceActiveBits will be treated as MAC, or NET address. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingSourceMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingSourceMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingSourceMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingSourceMacOrNet can be either macAddress or appleAddress.
INT maskingSourceCondition	1.3.6.1.4.1.164.4.1.6.3.1.11	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that matches the content of maskingSourceAddress. false - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that does not match the content of maskingSourceAddress.
ADR maskingDestAddress	1.3.6.1.4.1.164.4.1.6.3.1.12	GenAddress	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. The destination address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket. In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles). The IPX socket entered here has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care.
ADR maskingDestActiveBits	1.3.6.1.4.1.164.4.1.6.3.1.13	GenAddress	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the positions of the wild card characters (*) in the maskingDestAddress field. Only the 1's bit will be taken in considerations.
INT maskingDestMacOrNet	1.3.6.1.4.1.164.4.1.6.3.1.14	INTEGER	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingDestMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingDestMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingDestMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingDestMacOrNet can be either macAddress or appleAddress. The variable maskingDestAddress and maskingDestActiveBits will be treated as MAC, or NET address.
INT maskingDestCondition	1.3.6.1.4.1.164.4.1.6.3.1.15	INTEGER	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that matches the content of maskingDestAddress. false - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that does not match the content of maskingDestAddress.
INT maskingLowLevelProt	1.3.6.1.4.1.164.4.1.6.3.1.16	INTEGER	read-write	This field is set in conjunction with the maskingProtocolType variable. This variable specifies the low level protocol. The IPX socket entered in maskingDestAddress has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care.
INT maskingLowLevelProtCondition	1.3.6.1.4.1.164.4.1.6.3.1.17	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that matches the content of maskingLowLevelProt. false - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that does not match the content of maskingLowLevelProt.
I32 maskingHighLevelProt	1.3.6.1.4.1.164.4.1.6.3.1.18	Integer32	read-write	This field is set in connection to the maskingProtocolType variable. This variable specifies the high level protocols (application). As for today it supports just IP protocol stack. The object's value is a sum of the following instances values (selected by user): none (0), -- don't care ftp (1), ftpC (2), telnet (4), smtp (8), tftp (16), snmp (32), snmpTrap (64), ipRip (128), www (256), email (512), dns (1024), For Apple Protocol only: rtmp (2048), nbp (4096), atp (8192), aep (16384), zip (32768), adsp (65536), pap (131072), asp (262144) Example: if ftp(1), snmp(32) and snmpTrap(64) instances were selected, the value should be 97 (=1+32+64).
INT maskingHighLevelProtCondition	1.3.6.1.4.1.164.4.1.6.3.1.19	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that matches the content of maskingHighLevelProt. false - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that does not match the content of maskingHighLevelProt.
I32 maskingPortNum	1.3.6.1.4.1.164.4.1.6.3.1.20	Integer32	read-write	The port number is the same as in high level protocol. It specifies the dest. port in IP case or the dest. socket in case of IPX & apple protocols. IP - This object is applicable only if none (0) value was selected in maskingHighLevelProt. IPX - This object is applicable only if the socket entered in maskingDestAddress is 'don't care'(00) AND maskingLowLevelProt is NOT ipxRip or ipxSap. Apple - This option is applicable only if the socket entered in maskingDestAddress is 'don't care'(00).
INT maskingPortNumCondition	1.3.6.1.4.1.164.4.1.6.3.1.21	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingPortNum the packet contains data that matches the content of maskingPortNum. false - Condition is valid if at the position specified by maskingPortNum the packet contains data that does not match the content of maskingPortNum. This object is applicable only when maskingPortNum is applicable.
INT maskingOperation	1.3.6.1.4.1.164.4.1.6.3.1.22	INTEGER	read-write	The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list. smartMask = the operation and destination of the mask will be determined by the objects of the Smart Table (old masking table: radBridgeMaskTable). If maskingType is codConnect, the 'block' value is NOT allowed. If maskingType is codDisconnect, the 'forward' value is NOT allowed.
I32 maskingSrcPortNum	1.3.6.1.4.1.164.4.1.6.3.1.23	Integer32	read-write	The source port number. For IP: No Condition. For IPX: This object is applicable only if the socket entered in maskingSourceAddress is don't care (00) and maskingLowLevelProt is NOT ipxRip or ipxSap. For Apple:This object is applicable only if the socket entered in maskingSourceAddress is don't care (00).
INT maskingSrcPortNumCondition	1.3.6.1.4.1.164.4.1.6.3.1.24	INTEGER	read-write	The same as 'maskingPortNumCondition'. Relates to source port.
radBridgePerformance	1.3.6.1.4.1.164.4.1.7
radBridgeCurrentTable	1.3.6.1.4.1.164.4.1.7.1		not-accessible	The RAD Bridge Current table.
radBridgeCurrentEntry	1.3.6.1.4.1.164.4.1.7.1.1		not-accessible	An entry in the RAD Bridge Current table.
I32 radBridgeCurrentIndex	1.3.6.1.4.1.164.4.1.7.1.1.1	Integer32	read-only	The index of the Bridge interface or Bridge Port. It may be ifIndex.
G32 radBridgeCurrentIngressFilteringDiscardedFrames	1.3.6.1.4.1.164.4.1.7.1.1.2	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in the current 15 minute interval.
G32 radBridgeCurrentFrameTypeDiscardedFrames	1.3.6.1.4.1.164.4.1.7.1.1.3	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in the current 15 minute interval.
G32 radBridgeCurrentRxCorrectFrames	1.3.6.1.4.1.164.4.1.7.1.1.4	Gauge32	read-only	The counter associated with the number of Received Correct Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxCorrectBytes	1.3.6.1.4.1.164.4.1.7.1.1.5	Gauge32	read-only	The counter associated with the number of Received Correct Bytes, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.1.1.6	Gauge32	read-only	The counter associated with the number of times the associated radBridgeCurrentRxCorrectBytes counter has overflowed.
G32 radBridgeCurrentRxBcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.7	Gauge32	read-only	The counter associated with the number of Received Broadcast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxMcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.8	Gauge32	read-only	The counter associated with the number of Received Multicast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxCorrectFrames	1.3.6.1.4.1.164.4.1.7.1.1.9	Gauge32	read-only	The counter associated with the number of Transmitted Correct Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxCorrectBytes	1.3.6.1.4.1.164.4.1.7.1.1.10	Gauge32	read-only	The counter associated with the number of Transmitted Correct Bytes, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.1.1.11	Gauge32	read-only	The counter associated with the number of times the associated radBridgeCurrentTxCorrectBytes counter has overflowed.
G32 radBridgeCurrentTxBcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.12	Gauge32	read-only	The counter associated with the number of Transmitted Broadcast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxMcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.13	Gauge32	read-only	The counter associated with the number of Transmitted Multicast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxDropFrames	1.3.6.1.4.1.164.4.1.7.1.1.14	Gauge32	read-only	The counter associated with the number of Transmitted Dropped Frames, encountered by a Bridge Port in the current 15 minute interval.
radBridgeIntervalTable	1.3.6.1.4.1.164.4.1.7.2		not-accessible	The RAD Bridge Interval table.
radBridgeIntervalEntry	1.3.6.1.4.1.164.4.1.7.2.1		not-accessible	An entry in the RAD Bridge Interval table.
I32 radBridgeIntervalIndex	1.3.6.1.4.1.164.4.1.7.2.1.1	Integer32	read-only	The index of the bridge interface or Bridge Port. It may be ifIndex.
I32 radBridgeIntervalNumber	1.3.6.1.4.1.164.4.1.7.2.1.2	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
G32 radBridgeIntervalIngressFilteringDiscardedFrames	1.3.6.1.4.1.164.4.1.7.2.1.3	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalFrameTypeDiscardedFrames	1.3.6.1.4.1.164.4.1.7.2.1.4	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxCorrectFrames	1.3.6.1.4.1.164.4.1.7.2.1.5	Gauge32	read-only	The counter associated with the number of Received Correct Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxCorrectBytes	1.3.6.1.4.1.164.4.1.7.2.1.6	Gauge32	read-only	The counter associated with the number of Received Correct Bytes, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.2.1.7	Gauge32	read-only	The counter associated with the number of times the associated radBridgeIntervalRxCorrectBytes counter has overflowed.
G32 radBridgeIntervalRxBcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.8	Gauge32	read-only	The counter associated with the number of Received Broadcast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxMcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.9	Gauge32	read-only	The counter associated with the number of Received Multicast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxCorrectFrames	1.3.6.1.4.1.164.4.1.7.2.1.10	Gauge32	read-only	The counter associated with the number of Transmitted Correct Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxCorrectBytes	1.3.6.1.4.1.164.4.1.7.2.1.11	Gauge32	read-only	The counter associated with the number of Transmitted Correct Bytes, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.2.1.12	Gauge32	read-only	The counter associated with the number of times the associated radBridgeIntervalTxCorrectBytes counter has overflowed.
G32 radBridgeIntervalTxBcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.13	Gauge32	read-only	The counter associated with the number of Transmitted Broadcast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxMcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.14	Gauge32	read-only	The counter associated with the number of Transmitted Multicast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxDropFrames	1.3.6.1.4.1.164.4.1.7.2.1.15	Gauge32	read-only	The counter associated with the number of Transmitted Dropped Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
radBridgePortBaseVlan	1.3.6.1.4.1.164.4.1.8
radBridgePortBaseVlanTable	1.3.6.1.4.1.164.4.1.8.1		not-accessible	A table containing static configuration information for each VLAN configured into the device by management. All entries are permanent and will be restored after the device is reset.
radBridgePortBaseVlanEntry	1.3.6.1.4.1.164.4.1.8.1.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
I32 radBridgePortBaseVlanCnfgIdx	1.3.6.1.4.1.164.4.1.8.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
I32 radBridgePortBaseVlanIdx	1.3.6.1.4.1.164.4.1.8.1.1.2	Integer32	not-accessible	Index of the port based VLAN.
STR radBridgePortBaseVlanName	1.3.6.1.4.1.164.4.1.8.1.1.3	SnmpAdminString	read-create	An administratively assigned string, which may be used to identify the the port based VLAN.
POR radBridgePortBaseVlanEgressPorts	1.3.6.1.4.1.164.4.1.8.1.1.4	PortList	read-create	The set of ports which are permanently assigned to the egress list for this port based VLAN by management. The default value of this object is a string of zeros.
POR radBridgePortBaseVlanVirtualGroups	1.3.6.1.4.1.164.4.1.8.1.1.5	PortList	read-create	The set of Virtual Groups which are permanently assigned to this port based VLAN by management. (read Virtual Group instead of port in PortList Textual Convention) The default value of this object is a string of zeros.
ROW radBridgePortBaseVlanRowStatus	1.3.6.1.4.1.164.4.1.8.1.1.6	RowStatus	read-create	This object enable user to create/delete entries in this table.
INT radBridgePortBaseVlanMng	1.3.6.1.4.1.164.4.1.8.1.1.7	INTEGER	read-create	This object allows user to enable/disable management traffic on this VLAN. disable - only non-management data is allowed. enable - mixture of management traffic 0with other types of data is allowed.
radBridgePortVlanMemberTable	1.3.6.1.4.1.164.4.1.8.2		not-accessible	The Bridge Ports-VLAN Membership table. This table enables the user to assign: - Several VLANs to a Port. - Several Ports to a VLAN.
radBridgePortVlanMemberEntry	1.3.6.1.4.1.164.4.1.8.2.1		not-accessible	An entry in the Bridge Ports-VLANs Memebership table.
I32 radBridgePortVlanMemberBridgeIdx	1.3.6.1.4.1.164.4.1.8.2.1.1	Integer32	read-only	This object indicates the Bridge Index.
I32 radBridgePortVlanMemberPortIdx	1.3.6.1.4.1.164.4.1.8.2.1.2	Integer32	read-only	This object indicates the Bridge's Port Index. For some cases, it can be used as the Port ofIndex.
I32 radBridgePortVlanMemberVlanId	1.3.6.1.4.1.164.4.1.8.2.1.3	Integer32	read-only	This object indicates the VLAN ID.
ROW radBridgePortVlanMemberRowStatus	1.3.6.1.4.1.164.4.1.8.2.1.4	RowStatus	read-create	This object enables the user to create/delete entries in this table.
radBridgeGenCnfg	1.3.6.1.4.1.164.4.1.9
radBridgeGenFlowTable	1.3.6.1.4.1.164.4.1.9.1		not-accessible	A table containing static configuration information for Bridge configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
radBridgeGenFlowEntry	1.3.6.1.4.1.164.4.1.9.1.1		not-accessible	Static information for a Bridge configured into the device by management.
I32 radBridgeGenFlowCnfgIdx	1.3.6.1.4.1.164.4.1.9.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.
I32 radBridgeGenFlowIdx	1.3.6.1.4.1.164.4.1.9.1.1.2	Integer32	not-accessible	For Agent having more than one bridge, this index may be used as bridge index
ROW radBridgeGenFlowRowStatus	1.3.6.1.4.1.164.4.1.9.1.1.3	RowStatus	read-create	This object enable user to create/delete entries in this table.
I32 radBridgeGenFlowFloodOrBcastMaxRate	1.3.6.1.4.1.164.4.1.9.1.1.4	Integer32	read-create	This object controls maximum Flooding or Broadcast Rate: Max number of multicast along with unknown or flooded unicast frames allowed to enter any port. The number can be presented either as percentage of bandwidth, or bandwidth in Kbps. Once the limit is exceeded, any multicast or flooded frame entering from the port is discarded For RIC-155, and FCD-155 valid values are 3% , 6%, 12% and 100% = No Limit
INT radBridgeGenFlowQosMode	1.3.6.1.4.1.164.4.1.9.1.1.5	INTEGER	read-create	This object controls Quality of Service mode. User may select which field(s) (in case of fields - which one has precedence) will affect prioritization of data between egress queues.
INT radBridgeGenFlowSchedulingMode	1.3.6.1.4.1.164.4.1.9.1.1.6	INTEGER	read-create	This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme, Strict Priority (SP) or ATM CoS
INT radBridgeGenFlowBasicClassification	1.3.6.1.4.1.164.4.1.9.1.1.7	INTEGER	read-create	This object defines whether Classification based on Port should be taken into account (either as default, or in addition to other classifications).
I32 radBridgeGenFlowMulticastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.8	Integer32	read-create	The Traffic Class the received Multicast frame is mapped to.
I32 radBridgeGenFlowBroadcastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.9	Integer32	read-create	The Traffic Class the received Broadcast frame is mapped to.
I32 radBridgeGenFlowUnkownUnicastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.10	Integer32	read-create	The Traffic Class the received Unkonwn Unicast frame is mapped to.
radBridgeDot1qVlanStaticTable	1.3.6.1.4.1.164.4.1.9.2		not-accessible	A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
radBridgeDot1qVlanStaticEntry	1.3.6.1.4.1.164.4.1.9.2.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
POR radBridgeDot1qVlanTaggedPorts	1.3.6.1.4.1.164.4.1.9.2.1.1	PortList	read-create	The set of ports which should transmit egress packets for this VLAN as tagged.
POR radBridgeDot1qVlanUnmodifiedPorts	1.3.6.1.4.1.164.4.1.9.2.1.2	PortList	read-create	The set of ports which should transmit egress packets for this VLAN as unmodified.
INT radBridgeDot1qVlanSplitHorizon	1.3.6.1.4.1.164.4.1.9.2.1.3	INTEGER	read-create	When 'enable (3)', packets having this VLAN will not be switched back to other bridge ports which are members of this VLAN.
radDot1qPortVlanTable	1.3.6.1.4.1.164.4.1.9.3		not-accessible	A table containing control and status information for VLAN configuration per port.
radDot1qPortVlanEntry	1.3.6.1.4.1.164.4.1.9.3.1		not-accessible	Information controlling VLAN configuration for a port. This is indexed by dot1dBasePort.
INT radDot1qPortStacking	1.3.6.1.4.1.164.4.1.9.3.1.1	INTEGER	read-write	This object indicates the port stacking operation: unmodify (2) = Do not add Tag. tag (3) = Add Tag to Untagged Frames. stack (4) = Add Tag to all Frames.
INT radDot1qPortCopyOriginVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.2	INTEGER	read-write	This object indicates whether use the original VLAN Priority of the frame, as the priority of the VLAN added by this port.
I32 radDot1qPortDefaultVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.3	Integer32	read-write	Default VLAN Frame priority of the VLAN added by this port.
INT radDot1qPortTagStripping	1.3.6.1.4.1.164.4.1.9.3.1.4	INTEGER	read-write	This object indicates whether remove a tag from the frame on this port, frame with double tag will remain with one tag and frame with one tag will remain untagged.
INT radDot1qPortEgressTagHandling	1.3.6.1.4.1.164.4.1.9.3.1.5	INTEGER	read-write	This object indicates how is the Egress VLAN Tag processed. It is mainly for use with Double Tagging.
INT radDot1qPortIngressTagHandling	1.3.6.1.4.1.164.4.1.9.3.1.6	INTEGER	read-write	This object indicates how is the Ingress VLAN Tag processed. It is mainly for use with Double Tagging.
INT radDot1qPortReplaceVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.7	INTEGER	read-write	This object indicates whether for each received tagged frame on this Bridge Port - VLAN Priority will be replaced by another Priority. no(2) = no repacement yes(3) = VLAN Priority will be replaced For Egate-100: When value is 'yes', the original Priority is replaced by the Default Priority.
U32 radDot1qPortVlanEthType	1.3.6.1.4.1.164.4.1.9.3.1.8	Unsigned32	read-write	This object indicates the Ethernet Type. For some devices, it is applicable only when radDot1qPortStacking = stack.
INT radDot1qPortVlanCnodeLevel1Agent	1.3.6.1.4.1.164.4.1.9.3.1.9	INTEGER	read-write	Specify if a Level 1 cNode agent is enabled or not for the bridge port.
radBridgeGenCfgTable	1.3.6.1.4.1.164.4.1.9.4		not-accessible	A table containing Bridge configuration parameters.
radBridgeGenCfgEntry	1.3.6.1.4.1.164.4.1.9.4.1		not-accessible	Describes an entry in the radBridgeGenCfgTable.
I32 radBridgeGenCfgIdx	1.3.6.1.4.1.164.4.1.9.4.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg. For Agents that support only one Configuration, this object will be constant=1.
I32 radBridgeGenCfgIdx2	1.3.6.1.4.1.164.4.1.9.4.1.2	Integer32	not-accessible	For Agents having more than one bridge, this index may be used as bridge index
INT radBridgeGenCfgBridgeAction	1.3.6.1.4.1.164.4.1.9.4.1.3	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the tables maintained by the Bridge. After performing the action, Agent will automatically Set the value of this variable to noOp(255).
INT radBridgeAgingTimeSec	1.3.6.1.4.1.164.4.1.9.4.1.4	INTEGER	read-write	This variable duplicates scalar object dot1dTpAgingTimeThe of BRIDGE-MIB with configuration index and Bridge index. It defines the timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
U32 radBridgeMngVlanId	1.3.6.1.4.1.164.4.1.9.4.1.5	Unsigned32	read-write	This variable indicates the VLAN ID used for remote management traffic. 0 = Not Applicable.
U32 radBridgeLoopDetectVlanId	1.3.6.1.4.1.164.4.1.9.4.1.6	Unsigned32	read-write	This variable indicates the VLAN ID used for Loop Detection packets. Valid values: 1 - 4095: VLAN ID 0 - Means that the Loop Detection is Disabled.
INT radBridgeSplitHorizon	1.3.6.1.4.1.164.4.1.9.4.1.7	INTEGER	read-write	This object configure 'split horizon' switching between bridge Ports. - disable - normal (VLAN aware) bridge behavior. - enable - all packets, regardless their VLAN, coming from user side are blocked from being switched back to other user side bridge ports. - vlanBased - split horizon behavior is applicable only for specific VLANs, according to radBridgeDot1qVlanSplitHorizon.
U32 radBridgeEthType	1.3.6.1.4.1.164.4.1.9.4.1.8	Unsigned32	read-write	Value of Ethertype field in Ethernet frame. This field indicates which protocol is being transported in an ethernet frame.
INT radBridgeAgingTime	1.3.6.1.4.1.164.4.1.9.5	INTEGER	read-write	This variable defines whether the Aging Time will be finite or infinite. When selecting the finite (3) value, the exact time will be determined by another variable of the standard MIB (ex. 1493.dot1dTpAgingTime). or by radBridgeAgingTime below.
INT radBridgeMngFlow	1.3.6.1.4.1.164.4.1.9.6	INTEGER	read-write	This variable defines whether the Management Flow is passed through the bridge (enable) or not (disable).
radBridgeStatus	1.3.6.1.4.1.164.4.1.10
radBridgeInvBasePortTable	1.3.6.1.4.1.164.4.1.10.1		not-accessible	An inversed table to dot1dBasePortTable from RFC1493 with reduced information. This table index is known to the NMS and this way the needed information can be received by just one Get command, instead of searching the entire dot1dBasePortTable (where it is an attribute).
radBridgeInvBasePortEntry	1.3.6.1.4.1.164.4.1.10.1.1		not-accessible	The bridge port number for each bridge port interface index.
I32 radBridgeInvBasePortIfIndex	1.3.6.1.4.1.164.4.1.10.1.1.1	Integer32	read-only	The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this Bridge port.
I32 radBridgeInvBasePort	1.3.6.1.4.1.164.4.1.10.1.1.2	Integer32	read-only	The Bridge port number.
radBridgeStp	1.3.6.1.4.1.164.4.1.11
radBridgeStpCnfgTable	1.3.6.1.4.1.164.4.1.11.1		not-accessible	STP Configuration table. STP=Spanning Tree Protocol. It includes STP configurable parameters that in BRIDGE-MIB are scalars, while we need them per card/bridge/interface and per different configurations.
radBridgeStpCnfgEntry	1.3.6.1.4.1.164.4.1.11.1.1		not-accessible	An entry in the radBridgeStpCnfgTable.
I32 radBridgeStpCnfgIdx1	1.3.6.1.4.1.164.4.1.11.1.1.1	Integer32	not-accessible	This object indicates the Index of the Agent Configuration the following objects refer to. For Agents that support more than one configuration: 255=Temporary Cnfg ; Set can be done only to this configuration. For Agents that support only one configuration, this object will be constant=1.
I32 radBridgeStpCnfgIdx2	1.3.6.1.4.1.164.4.1.11.1.1.2	Integer32	not-accessible	For Agents having the table objects per Card/Bridge/Interface this will be the index of the Card/Bridge/Interface used.
TIM radBridgeStpCnfgForwardDelay	1.3.6.1.4.1.164.4.1.11.1.1.3	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for Forward Delay when this bridge is acting as the root. Note that the range for this parameter is related to the value of radBridgeStpCnfgMaxAge (according to 802.1D-1990 for the similar scalars of BRIDGE-MIB). The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM radBridgeStpCnfgMaxAge	1.3.6.1.4.1.164.4.1.11.1.1.4	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for MaxAge when this bridge is acting as the root. Note that the range for this parameter is related to the value of radBridgeStpCnfgHelloTime (according to 802.1D-1990 for the similar scalars of BRIDGE-MIB). The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM radBridgeStpCnfgHelloTime	1.3.6.1.4.1.164.4.1.11.1.1.5	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for Hello Time when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
I32 radBridgeStpCnfgPriority	1.3.6.1.4.1.164.4.1.11.1.1.6	Integer32	read-write	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID, per radBridgeStpCnfgIdx2 instance.
INT radBridgeStpCnfgStpVersion	1.3.6.1.4.1.164.4.1.11.1.1.7	INTEGER	read-write	This object determines the STP version used: stp - usual Spanning Tree Protocol. rstp - Rapid Spanning Tree Protocol.
radBridgeStpStatTable	1.3.6.1.4.1.164.4.1.11.2		not-accessible	STP Status table. STP=Spanning Tree Protocol. It includes STP status parameters that in BRIDGE-MIB are scalars, while we need them per card/bridge/interface. For devices that have several configurations, this table is for Status of the Active configuration.
radBridgeStpStatEntry	1.3.6.1.4.1.164.4.1.11.2.1		not-accessible	An entry in the radBridgeStpStatTable.
I32 radBridgeStpStatIdx	1.3.6.1.4.1.164.4.1.11.2.1.1	Integer32	not-accessible	For Agents having the table objects per Card/Bridge/Interface this will be the index of the Card/Bridge/Interface used.
TIM radBridgeStpStatForwardDelay	1.3.6.1.4.1.164.4.1.11.2.1.2	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to radBridgeStpCnfgForwardDelay which is the value that this bridge would start using if/when this bridge were to become the root.]
TIM radBridgeStpStatMaxAge	1.3.6.1.4.1.164.4.1.11.2.1.3	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM radBridgeStpStatHelloTime	1.3.6.1.4.1.164.4.1.11.2.1.4	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
BRI radBridgeStpStatDesignatedRoot	1.3.6.1.4.1.164.4.1.11.2.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
I32 radBridgeStpStatRootCost	1.3.6.1.4.1.164.4.1.11.2.1.6	Integer32	read-only	The cost of the path to the root as seen from this bridge.
INT radBridgeForwardingMode	1.3.6.1.4.1.164.4.1.12	INTEGER	read-write	This object determines the Bridge Forwarding Mode: transparent - Forward all frames received (not dependent on VLAN). filter - Filter frames received according to MAC Address. filterTagged = Filter frames received according to VLAN. transparentTagged = VLAN aware + Transparent.
radBridgePort	1.3.6.1.4.1.164.4.1.13
radBridgePortCnfgTable	1.3.6.1.4.1.164.4.1.13.1		not-accessible	The Bridge Port Configuration Table.
radBridgePortCnfgEntry	1.3.6.1.4.1.164.4.1.13.1.1		not-accessible	An entry in the table.
I32 radBridgePortCnfgIdx	1.3.6.1.4.1.164.4.1.13.1.1.1	Integer32	not-accessible	The first index of the table. It can serve for Configuration index, Bridge index or other.
I32 radBridgePortCnfgPrtIdx	1.3.6.1.4.1.164.4.1.13.1.1.2	Integer32	not-accessible	This object indicates the Bridge Port index.
I32 radBridgePortCnfgMaxMacAddr	1.3.6.1.4.1.164.4.1.13.1.1.3	Integer32	read-write	This object indicates the maximum number of total MAC Addresses (static and learned) supported by this Bridge Port.
INT radBridgePortCnfgMngFlow	1.3.6.1.4.1.164.4.1.13.1.1.4	INTEGER	read-write	This object indicates whether this Bridge Port is dedicated for management flow.
INT radBridgePortCnfgMcastMode	1.3.6.1.4.1.164.4.1.13.1.1.5	INTEGER	read-write	This object indicates this Bridge Port's Multicast Mode: flooding (1) - flood multicast MAC addresses forwarding (2) - forward multicast MAC addresses to the subnet indicated.
I32 radBridgePortCnfgDefaultVpi	1.3.6.1.4.1.164.4.1.13.1.1.6	Integer32	read-write	This object indicates the VPI of this Bridge Port's Default VCL. An incoming frame with priority that is not assigned to any VCL will be transferred to the Default VCL.
I32 radBridgePortCnfgDefaultVci	1.3.6.1.4.1.164.4.1.13.1.1.7	Integer32	read-write	This object indicates the VCI of this Bridge Port's Default VCL. An incoming frame with priority that is not assigned to any VCL will be transferred to the Default VCL.
I32 radBridgePortCnfgStatVlanId	1.3.6.1.4.1.164.4.1.13.1.1.8	Integer32	read-write	This object indicates the selected VlanId of the bridge port on which statistics are being collected. 0=no Statistics collected for VLAN on this bridge port.
I32 radBridgePortCnfgIngressMtu	1.3.6.1.4.1.164.4.1.13.1.1.9	Integer32	read-write	The size of the largest packet which can be received on the interface, specified in octets.
I32 radBridgePortCnfgEgressMtu	1.3.6.1.4.1.164.4.1.13.1.1.10	Integer32	read-write	The size of the largest packet which can be sent on the interface, specified in octets.
INT radBridgePortCnfgDot1x	1.3.6.1.4.1.164.4.1.13.1.1.11	INTEGER	read-write	This feature is currently supported via the variable ethIfTable.ethDot1xEnable. Determnines if the Port-Based Network Access Protocol (IEEE-802.1x)is enabled for the bridge Port.
radConverters	1.3.6.1.4.1.164.5
radGen	1.3.6.1.4.1.164.6
systems	1.3.6.1.4.1.164.6.1
systemsEvents	1.3.6.1.4.1.164.6.1.0			The events for RAD products.
NTF tftpStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.1			This trap is sent whenever the status of tftp changed.
NTF agnStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.2			This trap is sent whenever the state of the entity the agent is responsible for changed. TDM devices will send agnTestStatus variable to indicate the current test status.
NTF prtStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.3			This trap is sent whenever the state of a port changed. Attached, will be parameter/s that indicate the new port status. The attached variables will be specified in the specifications of the products supporting this trap.
NTF swdlStatusResult	1.3.6.1.4.1.164.6.1.0.4			This notification is sent when Software Down Load is finished. The attached object indicates the File Name.
NTF intSwdlSlotFileMismatch	1.3.6.1.4.1.164.6.1.0.5			This notification is sent when the card in the chosen slot doesn't match the chosen file. The attached object indicates the File Name.
NTF agnCounterChange	1.3.6.1.4.1.164.6.1.0.6			This notification is sent when the value of a specific Counter is changed. Agent can send as attached object the updated Counter. For details about this Counter and attached object, see spec of the relevant application.
NTF prtClkSrcChangeTrap	1.3.6.1.4.1.164.6.1.0.7			This trap is sent upon any port clock change.
NTF moduleFailTrap	1.3.6.1.4.1.164.6.1.0.8			This trap is sent upon a module failure.
NTF moduleInitFailTrap	1.3.6.1.4.1.164.6.1.0.9			This trap is sent upon a module initialization failure.
NTF clkSrcChangeTrap	1.3.6.1.4.1.164.6.1.0.10			This trap is sent upon any change in Clock Source.
NTF agnUploadDataTrap	1.3.6.1.4.1.164.6.1.0.11			This trap is sent upon an upload data session termination. For more details see product specification.
NTF enrollmentTrap	1.3.6.1.4.1.164.6.1.0.12			This trap is a periodically trap, which sent to manager untill Agent get any response (Get or Set) from this manager.
NTF agnPowerFailureTrap	1.3.6.1.4.1.164.6.1.0.13			This trap is sent upon power failure. It is applicable for the following devices: 1. Devices having one PS unit, which sense the failure in advance, and still have time to send this trap before it goes off. 2. Devices having 2 PS units and send this trap in order to notify a failure in one of the units.
NTF agnFanFailureTrap	1.3.6.1.4.1.164.6.1.0.14			This trap is sent upon fan failure/recovery.
NTF agnSystemParameterChangeTrap	1.3.6.1.4.1.164.6.1.0.15			This trap is sent upon any change of the systemParameter value.
NTF agnConfigDBChecksumError	1.3.6.1.4.1.164.6.1.0.16			This trap indicates that the database currently stored in the non-volatile memory of the device is corrupted
NTF agnAlarmBufferOverflow	1.3.6.1.4.1.164.6.1.0.17			This trap indicates that the quantity of alarm messages which have been written in the alarm buffer, since the last clear command, exceeds predefined threshold. (Buffer size) The new alarms are overwriting the oldest alarms (the first alarms written in the buffer). For LA-110,threshold value is 200 alarms.
NTF agnAlarmBufferClear	1.3.6.1.4.1.164.6.1.0.18			This trap indicates that alarm buffer has been cleared.
NTF agnParametersValueChanged	1.3.6.1.4.1.164.6.1.0.19			This trap indicates that due to software upgrade, some of the parameters are assigned new values
NTF agnDriverSwMismatch	1.3.6.1.4.1.164.6.1.0.20			There is mismatch between the SW driver and the HW of the device uplink interface.
NTF agnActualLowRate	1.3.6.1.4.1.164.6.1.0.21			The main link is synchronized at a rate lower than expected.
NTF xModemFileTransferStatusTrap	1.3.6.1.4.1.164.6.1.0.22			This trap is sent in the following cases: - When an xModem File Transfer Session begins. In this case, the trapVal.1 string sent will be: 'Start'. - When an xModem File Transfer Session ends. In this case, the trapVal.1 string sent will be one of the following, according to the way the session ended : - 'End: OK' - 'End: Failed'
NTF agnStationClkFailureTrap	1.3.6.1.4.1.164.6.1.0.23			This trap is sent upon Station Clock failure.
NTF successfulLogin	1.3.6.1.4.1.164.6.1.0.24			This trap is sent when a user performed successful Login via Terminal/Telnet/Web. This trap is used when the device is located at End-User's premises while management is at Service Provider's premises.
NTF failedLogin	1.3.6.1.4.1.164.6.1.0.25			This trap is sent when a user tried to Login via Terminal/Telnet/Web and failed. This trap is used when the device is located at End-User's premises while management is at Service Provider's premises.
NTF modlChangeTrap	1.3.6.1.4.1.164.6.1.0.26			This trap is sent whenever a module is inserted or removed. The trap should include the new module type (e.g. modlParamType).
NTF licenseUpdateTrap	1.3.6.1.4.1.164.6.1.0.27			This trap is sent whenever a license is successfully downloaded or whenever a license's demo duration is expired.
NTF agnClkSrcStateChangeTrap	1.3.6.1.4.1.164.6.1.0.28			The trap is sent upon change in Recovery Clock State.
NTF agnSelfTestResultChangeTrap	1.3.6.1.4.1.164.6.1.0.29			The trap is sent upon each change in the result of a Self State operation.
NTF agnClkSrcFrequencyAlarmTrap	1.3.6.1.4.1.164.6.1.0.31			The trap is sent upon Recovered Clock Frequency alarm.
radSysTR	1.3.6.1.4.1.164.6.1.1
radRADring	1.3.6.1.4.1.164.6.1.1.1
radTMA	1.3.6.1.4.1.164.6.1.1.2
radRingMonitor	1.3.6.1.4.1.164.6.1.1.3
radSysFddi	1.3.6.1.4.1.164.6.1.2
radFDX100	1.3.6.1.4.1.164.6.1.2.1
radSysWan	1.3.6.1.4.1.164.6.1.3
radSysWanEvents	1.3.6.1.4.1.164.6.1.3.0			The events for RAD Wan products.
NTF alarmStatusTrap	1.3.6.1.4.1.164.6.1.3.0.5			The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm.
NTF systemTrap	1.3.6.1.4.1.164.6.1.3.0.6			This trap alerts of major problems in the device.
NTF alarmLOS	1.3.6.1.4.1.164.6.1.3.0.7			This trap indicates Loss Of Signal.
NTF alarmLOF	1.3.6.1.4.1.164.6.1.3.0.8			This trap indicates Loss Of Frame.
NTF channelOperStatusTrap	1.3.6.1.4.1.164.6.1.3.0.9			This trap is sent upon any change in one or more channels.
NTF alarmAIS	1.3.6.1.4.1.164.6.1.3.0.10			This trap indicates AIS.
NTF alarmRDI	1.3.6.1.4.1.164.6.1.3.0.11			This trap indicates RDI.
NTF alarmFEBE	1.3.6.1.4.1.164.6.1.3.0.12			This trap indicates FEBE.
NTF localConnStatusTrap	1.3.6.1.4.1.164.6.1.3.0.13			This trap is sent upon a change in Local connectivity of Bundle connection.
NTF remoteConnStatusTrap	1.3.6.1.4.1.164.6.1.3.0.14			This trap is sent upon a change in Remote connectivity of Bundle connection.
NTF bundleConnectionStatusTrap	1.3.6.1.4.1.164.6.1.3.0.15			This trap is sent upon any change in the connectivity status of a Bundle (ip2IfOperStatus). The ifAlias index is the ifIndex of the bundle that its status has been changed.
radMP2100	1.3.6.1.4.1.164.6.1.3.1
radMP2104	1.3.6.1.4.1.164.6.1.3.2
radMP2100B	1.3.6.1.4.1.164.6.1.3.3
radMP2100F	1.3.6.1.4.1.164.6.1.3.4
radMP2100H	1.3.6.1.4.1.164.6.1.3.5
radMP2104H	1.3.6.1.4.1.164.6.1.3.6
radMP2200B	1.3.6.1.4.1.164.6.1.3.7
radMP2200F	1.3.6.1.4.1.164.6.1.3.8
radMX3000	1.3.6.1.4.1.164.6.1.3.9
radMX3004	1.3.6.1.4.1.164.6.1.3.10
radMX30	1.3.6.1.4.1.164.6.1.3.11
radMX300	1.3.6.1.4.1.164.6.1.3.12
radVOIP	1.3.6.1.4.1.164.6.1.3.13
radKM2100	1.3.6.1.4.1.164.6.1.3.15
radKM2104	1.3.6.1.4.1.164.6.1.3.16
radDXC30	1.3.6.1.4.1.164.6.1.3.20
radDXC10A	1.3.6.1.4.1.164.6.1.3.21
radDXC8R	1.3.6.1.4.1.164.6.1.3.22
radDXC30E	1.3.6.1.4.1.164.6.1.3.23
radDXC3000	1.3.6.1.4.1.164.6.1.3.24
radDXC8RNew	1.3.6.1.4.1.164.6.1.3.25
radFcdT1LC	1.3.6.1.4.1.164.6.1.3.26
radFcdE1LC	1.3.6.1.4.1.164.6.1.3.27
radFcdT1L	1.3.6.1.4.1.164.6.1.3.28
radFcdE1L	1.3.6.1.4.1.164.6.1.3.29
radFcdT1	1.3.6.1.4.1.164.6.1.3.30
radFcdE1	1.3.6.1.4.1.164.6.1.3.31
radFcdE1I	1.3.6.1.4.1.164.6.1.3.32
radFcdT1M	1.3.6.1.4.1.164.6.1.3.33
radFcdE1M	1.3.6.1.4.1.164.6.1.3.34
radFcdIP	1.3.6.1.4.1.164.6.1.3.35
radFcdT1A	1.3.6.1.4.1.164.6.1.3.36
radFcdE1A	1.3.6.1.4.1.164.6.1.3.37
radFcdW	1.3.6.1.4.1.164.6.1.3.38
radFcdSTM	1.3.6.1.4.1.164.6.1.3.39
radHtuE1Sa	1.3.6.1.4.1.164.6.1.3.40
radHtuE1	1.3.6.1.4.1.164.6.1.3.41
radHtu2Sa	1.3.6.1.4.1.164.6.1.3.42
radHtu2	1.3.6.1.4.1.164.6.1.3.43
radAsmi450R768Sa	1.3.6.1.4.1.164.6.1.3.44
radAsmi450R768	1.3.6.1.4.1.164.6.1.3.45
radAsmi450R1152Sa	1.3.6.1.4.1.164.6.1.3.46
radAsmi450R1152	1.3.6.1.4.1.164.6.1.3.47
radLrs12F	1.3.6.1.4.1.164.6.1.3.48
radLrs12B	1.3.6.1.4.1.164.6.1.3.49
radLrs52	1.3.6.1.4.1.164.6.1.3.50
radHcdE1Sa	1.3.6.1.4.1.164.6.1.3.51
radHcdE1	1.3.6.1.4.1.164.6.1.3.52
radHtuT1Sa	1.3.6.1.4.1.164.6.1.3.53
radHtuT1	1.3.6.1.4.1.164.6.1.3.54
radOptimux4E1	1.3.6.1.4.1.164.6.1.3.55
radOptimux4T1	1.3.6.1.4.1.164.6.1.3.56
radOptimuxXLE1	1.3.6.1.4.1.164.6.1.3.57
radOptimuxXLT1	1.3.6.1.4.1.164.6.1.3.58
radOptimuxXL16E1	1.3.6.1.4.1.164.6.1.3.59
radImx64	1.3.6.1.4.1.164.6.1.3.60
radImx6L	1.3.6.1.4.1.164.6.1.3.61
radImx2	1.3.6.1.4.1.164.6.1.3.62
radImx4T1	1.3.6.1.4.1.164.6.1.3.63
radImx4E1	1.3.6.1.4.1.164.6.1.3.64
radImx2T1E1	1.3.6.1.4.1.164.6.1.3.65
radIMXI4	1.3.6.1.4.1.164.6.1.3.66
radOptimux155	1.3.6.1.4.1.164.6.1.3.67
radOptimux4T1L	1.3.6.1.4.1.164.6.1.3.68
radOptimux4E1L	1.3.6.1.4.1.164.6.1.3.69
radHtuE1SaV2	1.3.6.1.4.1.164.6.1.3.70
radHtuE1V2	1.3.6.1.4.1.164.6.1.3.71
radFomiE3	1.3.6.1.4.1.164.6.1.3.72
radFomiT3	1.3.6.1.4.1.164.6.1.3.73
radOpt4E1C	1.3.6.1.4.1.164.6.1.3.74
radOpt4T1C	1.3.6.1.4.1.164.6.1.3.75
radPrbiE3	1.3.6.1.4.1.164.6.1.3.76
radPrbiT3	1.3.6.1.4.1.164.6.1.3.77
radHcd4Sa	1.3.6.1.4.1.164.6.1.3.78
radOptimuxT3	1.3.6.1.4.1.164.6.1.3.79
radFRmon	1.3.6.1.4.1.164.6.1.3.80
radIpMux4	1.3.6.1.4.1.164.6.1.3.81
radIpMux1	1.3.6.1.4.1.164.6.1.3.82
radIpMux16	1.3.6.1.4.1.164.6.1.3.83
radIpMux1E	1.3.6.1.4.1.164.6.1.3.84
radVmux2100	1.3.6.1.4.1.164.6.1.3.85
radMP104	1.3.6.1.4.1.164.6.1.3.86
radMP204	1.3.6.1.4.1.164.6.1.3.87
radVmux110	1.3.6.1.4.1.164.6.1.3.88
radFcd155	1.3.6.1.4.1.164.6.1.3.90
radIpMux8	1.3.6.1.4.1.164.6.1.3.91
radOptimux155DS3	1.3.6.1.4.1.164.6.1.3.92
radOptimuxT3L	1.3.6.1.4.1.164.6.1.3.93
radGmux2000	1.3.6.1.4.1.164.6.1.3.94
radOp16E1L	1.3.6.1.4.1.164.6.1.3.95
radOp16E1LS	1.3.6.1.4.1.164.6.1.3.96
radPRBm20	1.3.6.1.4.1.164.6.1.3.97
radPRBm22	1.3.6.1.4.1.164.6.1.3.98
radAsmi52A	1.3.6.1.4.1.164.6.1.3.99
radOpXLE1	1.3.6.1.4.1.164.6.1.3.100
radOpXLT1	1.3.6.1.4.1.164.6.1.3.101
radOpXL16E1	1.3.6.1.4.1.164.6.1.3.102
radOp4E1	1.3.6.1.4.1.164.6.1.3.103
radOp4T1	1.3.6.1.4.1.164.6.1.3.104
radDxc4	1.3.6.1.4.1.164.6.1.3.105
radIpMux11	1.3.6.1.4.1.164.6.1.3.106
radIpMux14	1.3.6.1.4.1.164.6.1.3.107
radOp1550	1.3.6.1.4.1.164.6.1.3.108
radFdsl101	1.3.6.1.4.1.164.6.1.3.110
radFdsl201	1.3.6.1.4.1.164.6.1.3.111
radVmux120	1.3.6.1.4.1.164.6.1.3.112
radVmux2200	1.3.6.1.4.1.164.6.1.3.113
radVmux400	1.3.6.1.4.1.164.6.1.3.114
radIpMux116	1.3.6.1.4.1.164.6.1.3.115
radOp4E1LNew	1.3.6.1.4.1.164.6.1.3.116
radOp4T1LNew	1.3.6.1.4.1.164.6.1.3.117
radFcd155E	1.3.6.1.4.1.164.6.1.3.118
radFcd155ES	1.3.6.1.4.1.164.6.1.3.119
radMP4100	1.3.6.1.4.1.164.6.1.3.120
radAsmi52L	1.3.6.1.4.1.164.6.1.3.121
radVmux210	1.3.6.1.4.1.164.6.1.3.122
radOp34E1	1.3.6.1.4.1.164.6.1.3.123
radVmux312	1.3.6.1.4.1.164.6.1.3.124
radVmux404	1.3.6.1.4.1.164.6.1.3.125
radVmux420	1.3.6.1.4.1.164.6.1.3.126
radIpMux12	1.3.6.1.4.1.164.6.1.3.127
radOptimux4E1V3dot5	1.3.6.1.4.1.164.6.1.3.128
radOptimux4E1Mar06	1.3.6.1.4.1.164.6.1.3.129
radFcd155EwAPS	1.3.6.1.4.1.164.6.1.3.130
radOptimux4T1Mar06	1.3.6.1.4.1.164.6.1.3.131
radFcd155EwAPS2pdh	1.3.6.1.4.1.164.6.1.3.132
radVmux320	1.3.6.1.4.1.164.6.1.3.133
radMP2100VoIP	1.3.6.1.4.1.164.6.1.3.134
radMP2104VoIP	1.3.6.1.4.1.164.6.1.3.135
radIpMux24	1.3.6.1.4.1.164.6.1.3.136
radOp4E1NG1	1.3.6.1.4.1.164.6.1.3.137
radOp4T1NG1	1.3.6.1.4.1.164.6.1.3.138
radOp25	1.3.6.1.4.1.164.6.1.3.139
radAsmi54	1.3.6.1.4.1.164.6.1.3.140
radVmux314	1.3.6.1.4.1.164.6.1.3.141
radFcd622	1.3.6.1.4.1.164.6.1.3.142
radLrs22	1.3.6.1.4.1.164.6.1.3.143
radUNT20E1	1.3.6.1.4.1.164.6.1.3.144
radIpMux2L	1.3.6.1.4.1.164.6.1.3.145
radUNT20Fcd	1.3.6.1.4.1.164.6.1.3.146
radIpMux216	1.3.6.1.4.1.164.6.1.3.147
radLrs102	1.3.6.1.4.1.164.6.1.3.148
radGmux2004	1.3.6.1.4.1.164.6.1.3.149
radLrs102unbal	1.3.6.1.4.1.164.6.1.3.150
radLrs16	1.3.6.1.4.1.164.6.1.3.151
radVmux405	1.3.6.1.4.1.164.6.1.3.152
radVmux425	1.3.6.1.4.1.164.6.1.3.153
radMiniCVS	1.3.6.1.4.1.164.6.1.3.154
radSysBRG	1.3.6.1.4.1.164.6.1.4
radTRE1	1.3.6.1.4.1.164.6.1.4.1
radTRE1D	1.3.6.1.4.1.164.6.1.4.2
radTRE8	1.3.6.1.4.1.164.6.1.4.3
radTRE8D	1.3.6.1.4.1.164.6.1.4.4
radMBE1	1.3.6.1.4.1.164.6.1.4.5
radMBE1D	1.3.6.1.4.1.164.6.1.4.6
radMBE8	1.3.6.1.4.1.164.6.1.4.7
radMBE8D	1.3.6.1.4.1.164.6.1.4.8
radMLBT	1.3.6.1.4.1.164.6.1.4.9
radFEB4DAS	1.3.6.1.4.1.164.6.1.4.10
radTrimBrg10	1.3.6.1.4.1.164.6.1.4.11
radTrimBrg16	1.3.6.1.4.1.164.6.1.4.12
radRRTRE8	1.3.6.1.4.1.164.6.1.4.13
radRRTRE8D	1.3.6.1.4.1.164.6.1.4.14
radRRMLBT	1.3.6.1.4.1.164.6.1.4.15
radRRMLBTF	1.3.6.1.4.1.164.6.1.4.16
radRRTRE1D	1.3.6.1.4.1.164.6.1.4.17
radTRERAS	1.3.6.1.4.1.164.6.1.4.18
radTRERASa	1.3.6.1.4.1.164.6.1.4.19
radMBERAS	1.3.6.1.4.1.164.6.1.4.20
radMBERASa	1.3.6.1.4.1.164.6.1.4.21
radFEB4FDX	1.3.6.1.4.1.164.6.1.4.22
radFEB4SAS	1.3.6.1.4.1.164.6.1.4.23
radRRFTBDAS	1.3.6.1.4.1.164.6.1.4.24
radRRFTBSAS	1.3.6.1.4.1.164.6.1.4.25
radFTBDAS	1.3.6.1.4.1.164.6.1.4.26
radFTBSAS	1.3.6.1.4.1.164.6.1.4.27
radFastWay100	1.3.6.1.4.1.164.6.1.4.28
radSysCnvrtr	1.3.6.1.4.1.164.6.1.5
radSTC1	1.3.6.1.4.1.164.6.1.5.1
radSTC2	1.3.6.1.4.1.164.6.1.5.3
radSTC1UDP	1.3.6.1.4.1.164.6.1.5.4
radSTC2UDP	1.3.6.1.4.1.164.6.1.5.6
radFTC1	1.3.6.1.4.1.164.6.1.5.10
radFTC2	1.3.6.1.4.1.164.6.1.5.12
radFTC1UDP	1.3.6.1.4.1.164.6.1.5.13
radFTC2UDP	1.3.6.1.4.1.164.6.1.5.15
radSEC1	1.3.6.1.4.1.164.6.1.5.20
radSEC2	1.3.6.1.4.1.164.6.1.5.22
radSEC1UDP	1.3.6.1.4.1.164.6.1.5.23
radSEC2UDP	1.3.6.1.4.1.164.6.1.5.25
radFEC1	1.3.6.1.4.1.164.6.1.5.30
radFEC2	1.3.6.1.4.1.164.6.1.5.32
radFEC1UDP	1.3.6.1.4.1.164.6.1.5.33
radFEC2UDP	1.3.6.1.4.1.164.6.1.5.35
radRIC155	1.3.6.1.4.1.164.6.1.5.36
radRICE1	1.3.6.1.4.1.164.6.1.5.37
radETX102	1.3.6.1.4.1.164.6.1.5.38
radRIC155GE	1.3.6.1.4.1.164.6.1.5.39
radRiciT3	1.3.6.1.4.1.164.6.1.5.40
radRiciE3	1.3.6.1.4.1.164.6.1.5.41
radRiciT1	1.3.6.1.4.1.164.6.1.5.42
radETX202	1.3.6.1.4.1.164.6.1.5.43
radETX105	1.3.6.1.4.1.164.6.1.5.44
radETX205	1.3.6.1.4.1.164.6.1.5.45
radRiciSE	1.3.6.1.4.1.164.6.1.5.46
radRIC622GE	1.3.6.1.4.1.164.6.1.5.47
radSPH	1.3.6.1.4.1.164.6.1.5.48
radMiricE1T1	1.3.6.1.4.1.164.6.1.5.49
radMiricE3T3	1.3.6.1.4.1.164.6.1.5.50
radEthAccess	1.3.6.1.4.1.164.6.1.6
radETX510	1.3.6.1.4.1.164.6.1.6.1
radEGate100	1.3.6.1.4.1.164.6.1.6.2
radEGate20	1.3.6.1.4.1.164.6.1.6.3
radRici8E1	1.3.6.1.4.1.164.6.1.6.4
radRici8T1	1.3.6.1.4.1.164.6.1.6.5
radRici4E1	1.3.6.1.4.1.164.6.1.6.6
radRici4T1	1.3.6.1.4.1.164.6.1.6.7
radETX550	1.3.6.1.4.1.164.6.1.6.9
radRici16	1.3.6.1.4.1.164.6.1.6.10
radETX102A	1.3.6.1.4.1.164.6.1.6.11
radETX202A	1.3.6.1.4.1.164.6.1.6.12
radETX201A	1.3.6.1.4.1.164.6.1.6.13
radETX201	1.3.6.1.4.1.164.6.1.6.14
radUNT20Ric	1.3.6.1.4.1.164.6.1.6.15
radRici4E1L	1.3.6.1.4.1.164.6.1.6.16
radRici8E1L	1.3.6.1.4.1.164.6.1.6.17
radRici155GE	1.3.6.1.4.1.164.6.1.6.18
radRici622GE	1.3.6.1.4.1.164.6.1.6.19
radETX208	1.3.6.1.4.1.164.6.1.6.20
radETX202AW	1.3.6.1.4.1.164.6.1.6.21
radETX102H	1.3.6.1.4.1.164.6.1.6.22
radETX202H	1.3.6.1.4.1.164.6.1.6.23
radSysStkHub	1.3.6.1.4.1.164.6.1.7
radRBHE	1.3.6.1.4.1.164.6.1.7.1
radRBHEEvents	1.3.6.1.4.1.164.6.1.7.1.0			The events for RAD Stackable products.
radRBHT	1.3.6.1.4.1.164.6.1.7.2
radRBHTEvents	1.3.6.1.4.1.164.6.1.7.2.0			The events for RAD Stackable products.
radETS4fddiDAS	1.3.6.1.4.1.164.6.1.7.3
radETS4fddiSAS	1.3.6.1.4.1.164.6.1.7.4
radSAHEMX	1.3.6.1.4.1.164.6.1.7.5
radSAHTM	1.3.6.1.4.1.164.6.1.7.6
radETS4	1.3.6.1.4.1.164.6.1.7.7
radSAHEMU	1.3.6.1.4.1.164.6.1.7.8
unknown	1.3.6.1.4.1.164.6.1.7.9
radSAH16Eint	1.3.6.1.4.1.164.6.1.7.10
radSAH16Tint	1.3.6.1.4.1.164.6.1.7.11
radSAH16Eext	1.3.6.1.4.1.164.6.1.7.12
radSAH16Text	1.3.6.1.4.1.164.6.1.7.13
radSysPS	1.3.6.1.4.1.164.6.1.8
radSysPSEvents	1.3.6.1.4.1.164.6.1.8.0			The events for RAD Packet Switch (PS) products.
radSPS2	1.3.6.1.4.1.164.6.1.8.1
radSPS3	1.3.6.1.4.1.164.6.1.8.2
radSPS6	1.3.6.1.4.1.164.6.1.8.3
radSPS9	1.3.6.1.4.1.164.6.1.8.4
radSPS12	1.3.6.1.4.1.164.6.1.8.5
radAPD2	1.3.6.1.4.1.164.6.1.8.6
radAPD8	1.3.6.1.4.1.164.6.1.8.7
radAPS8	1.3.6.1.4.1.164.6.1.8.8
radAPS16	1.3.6.1.4.1.164.6.1.8.9
radAPS24	1.3.6.1.4.1.164.6.1.8.10
radSPS3S	1.3.6.1.4.1.164.6.1.8.11
radFPS8	1.3.6.1.4.1.164.6.1.8.12
radFPS12	1.3.6.1.4.1.164.6.1.8.13
radSPS3ScSL	1.3.6.1.4.1.164.6.1.8.14
radSPS3Sc2S	1.3.6.1.4.1.164.6.1.8.15
radFPS8c	1.3.6.1.4.1.164.6.1.8.16
radFPS4	1.3.6.1.4.1.164.6.1.8.17
radSPS4	1.3.6.1.4.1.164.6.1.8.18
radSysEth	1.3.6.1.4.1.164.6.1.9
radEP8T	1.3.6.1.4.1.164.6.1.9.1
radEP4TAUI	1.3.6.1.4.1.164.6.1.9.2
radEP4T2FL	1.3.6.1.4.1.164.6.1.9.3
radEP4TFL	1.3.6.1.4.1.164.6.1.9.4
radEP4FL	1.3.6.1.4.1.164.6.1.9.5
radEPR8T	1.3.6.1.4.1.164.6.1.9.7
radEPR4TAUI	1.3.6.1.4.1.164.6.1.9.8
radEPR4T2FL	1.3.6.1.4.1.164.6.1.9.9
radEPR4TFL	1.3.6.1.4.1.164.6.1.9.10
radEPR4FL	1.3.6.1.4.1.164.6.1.9.11
radSysRtr	1.3.6.1.4.1.164.6.1.11
radSysRtrEvents	1.3.6.1.4.1.164.6.1.11.0			The events for RAD Router products.
radRTED	1.3.6.1.4.1.164.6.1.11.1
radRTEM	1.3.6.1.4.1.164.6.1.11.2
radRTEC	1.3.6.1.4.1.164.6.1.11.3
radWebRanger	1.3.6.1.4.1.164.6.1.11.4
radTinyRouter	1.3.6.1.4.1.164.6.1.11.5
radLA240	1.3.6.1.4.1.164.6.1.11.6
radSuperLan	1.3.6.1.4.1.164.6.1.11.7
radLA240I	1.3.6.1.4.1.164.6.1.11.8
radFcdIsdn	1.3.6.1.4.1.164.6.1.11.9
radEFcdIp	1.3.6.1.4.1.164.6.1.11.10
radFcdIpD	1.3.6.1.4.1.164.6.1.11.11
radFcdIpM	1.3.6.1.4.1.164.6.1.11.12
radFcdIpL	1.3.6.1.4.1.164.6.1.11.13
radSysAtm	1.3.6.1.4.1.164.6.1.12
radSysAtmEvents	1.3.6.1.4.1.164.6.1.12.0			The events for RAD ATM products.
NTF atmAceSystemTrap	1.3.6.1.4.1.164.6.1.12.0.6			This trap alerts of major problems in the device.
NTF atmAceAlarmForwardingTrap	1.3.6.1.4.1.164.6.1.12.0.7			This trap is sent upon starting or stopping Alarm Forwarding Mechanism.
NTF atmAceDateAndTimeRequest	1.3.6.1.4.1.164.6.1.12.0.8			This trap is sent upon restart. Upon recieving this trap the NMS will set the device's date and time. This trap's purpose is to fix a problem in ACE2002, ACE-2002E, ACE-202. The problem is that the Date and Time is stored in the NVRAM, and when the NVRAM's battery is empty, the device loses this information.
NTF atmAceAlarmLOS	1.3.6.1.4.1.164.6.1.12.0.16			This trap indicates Loss Of Signal.
NTF atmAceAlarmLOF	1.3.6.1.4.1.164.6.1.12.0.17			This trap indicates Loss Of Frame.
NTF atmAceAlarmLCD	1.3.6.1.4.1.164.6.1.12.0.18			This trap indicates Loss of Cell Delineation.
NTF atmAceAlarmSLM	1.3.6.1.4.1.164.6.1.12.0.19			This trap indicates Signal Line Mismatch.
NTF atmAceAlarmLOP	1.3.6.1.4.1.164.6.1.12.0.20			This trap indicates Loss of Pointer.
NTF atmAceAlarmLineAIS	1.3.6.1.4.1.164.6.1.12.0.21			This trap indicates Line AIS.
NTF atmAceAlarmPathAIS	1.3.6.1.4.1.164.6.1.12.0.22			This trap indicates Path AIS.
NTF atmAceAlarmLineRDI	1.3.6.1.4.1.164.6.1.12.0.23			This trap indicates Line RDI.
NTF atmAceAlarmPathRDI	1.3.6.1.4.1.164.6.1.12.0.24			This trap indicates Path RDIand Path RAI(Yellow) for DS1 interfaces.
NTF atmAceAlarmSectionBIP	1.3.6.1.4.1.164.6.1.12.0.25			This trap indicates Section Bit Interleave Parity.
NTF atmAceAlarmLineBIP	1.3.6.1.4.1.164.6.1.12.0.26			This trap indicates Line Bit Interleave Parity.
NTF atmAceAlarmPathBIP	1.3.6.1.4.1.164.6.1.12.0.27			This trap indicates Path Bit Interleave Parity.
NTF atmAceAlarmLineFEBE	1.3.6.1.4.1.164.6.1.12.0.28			This trap indicates Line Far End Block Error.
NTF atmAceAlarmPathFEBE	1.3.6.1.4.1.164.6.1.12.0.29			This trap indicates Path Far End Block Error.
NTF atmAceAlarmPlcpLOF	1.3.6.1.4.1.164.6.1.12.0.30			This trap indicates T3 PLCP Loss Of Frame.
NTF atmAceAlarmPlcpYELLOW	1.3.6.1.4.1.164.6.1.12.0.31			This trap indicates T3 Plcp Yellow.
NTF atmAceAlarmPlcpBIP	1.3.6.1.4.1.164.6.1.12.0.32			This trap indicates T3 Plcp Bit Interleave Parity.
NTF atmAceAlarmPlcpFEBE	1.3.6.1.4.1.164.6.1.12.0.33			This trap indicates T3 Plcp Far End Block Error.
NTF atmAceAlarmPlcpP1P2	1.3.6.1.4.1.164.6.1.12.0.34			This trap indicates T3 Plcp Parity errors in P1/P2 bytes.
NTF atmAceAlarmUAS	1.3.6.1.4.1.164.6.1.12.0.35			This trap is sent upon UAS start or end per port.
NTF atmAceAlarmCluster	1.3.6.1.4.1.164.6.1.12.0.36			This trap is sent upon atmNteAlarmType start or end, for a cluster of VPs/VCs (according to atmNteLevel) with the same alarm on the same physical port. This trap replaces sending the same alarm for a big quantity (the quantity described in the product specification document) of VPs/VCs in order to prevent flooding the NMS and the network with traps.
NTF atmAceHwFailure	1.3.6.1.4.1.164.6.1.12.0.37			This trap is sent upon HW failure per port.
NTF atmAceUnavailableBwTrap	1.3.6.1.4.1.164.6.1.12.0.38			This trap is sent when Bandwidth allocation is > max possible value for the installed card. For ACE2002 this trap will be sent for the following cases: Card insertion - if the total Input and/or Output Bandwidth is over allocated, then the specific card rate will be set to 0 and this trap will be sent with the Input/Output rates values. Upgrade from former version - when an over allocated Bandwidth is detected, this trap will be sent with atmConfIfInputRate=atmConfIfOutputRate=0xFFFFFFFF.
NTF atmAceAlarmVpContinuityLoss	1.3.6.1.4.1.164.6.1.12.0.40			This trap indicates Loss of Continuity Check on a VP Connection.
NTF atmAceAlarmVpAISReception	1.3.6.1.4.1.164.6.1.12.0.41			This trap indicates AIS Reception on a VP Connection.
NTF atmAceAlarmVpRDIReception	1.3.6.1.4.1.164.6.1.12.0.42			This trap indicates RDI Reception on a VP Connection.
NTF atmAceAlarmVpErroredCells	1.3.6.1.4.1.164.6.1.12.0.43			This trap indicates Errored Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpLostCells	1.3.6.1.4.1.164.6.1.12.0.44			This trap indicates Lost Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpMisinsertedCells	1.3.6.1.4.1.164.6.1.12.0.45			This trap indicates Misinserted Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpUAS	1.3.6.1.4.1.164.6.1.12.0.46			This trap is sent upon UAS start or end per VP.
NTF atmAceAlarmVpLoopback	1.3.6.1.4.1.164.6.1.12.0.47			This trap is sent upon OAM LoopBack fail status per VP.
NTF atmAceAlarmVpGCRAViolation	1.3.6.1.4.1.164.6.1.12.0.48			This trap indicates GCRA violation on a VP Connection reported by UPC device.
NTF atmAceAlarmVcContinuityLoss	1.3.6.1.4.1.164.6.1.12.0.56			This trap indicates Loss of Continuity Check on a VC Connection.
NTF atmAceAlarmVcAISReception	1.3.6.1.4.1.164.6.1.12.0.57			This trap indicates AIS Reception on a VC.
NTF atmAceAlarmVcRDIReception	1.3.6.1.4.1.164.6.1.12.0.58			This trap indicates RDI Reception on a VC Connection.
NTF atmAceAlarmVcErroredCells	1.3.6.1.4.1.164.6.1.12.0.59			This trap indicates Errored Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcLostCells	1.3.6.1.4.1.164.6.1.12.0.60			This trap indicates Lost Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcMisinsertedCells	1.3.6.1.4.1.164.6.1.12.0.61			This trap indicates Misinserted Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcUnexpectedCell	1.3.6.1.4.1.164.6.1.12.0.62			This trap indicates an unexpected cell from user or network port.
NTF atmAceAlarmVcUAS	1.3.6.1.4.1.164.6.1.12.0.63			This trap is sent upon UAS start or end per VC.
NTF atmAceAlarmVcLoopback	1.3.6.1.4.1.164.6.1.12.0.64			This trap is sent upon OAM LoopBack fail status per VC.
NTF atmAceAlarmVcGCRAViolation	1.3.6.1.4.1.164.6.1.12.0.65			This trap indicates GCRA violation on a VC Connection reported by UPC device.
radStarSwitch	1.3.6.1.4.1.164.6.1.12.1
radStarSwitchATM25	1.3.6.1.4.1.164.6.1.12.1.1
radStarSwitchATM25L	1.3.6.1.4.1.164.6.1.12.1.2
radStarSwitchATM155	1.3.6.1.4.1.164.6.1.12.1.3
radAtmCsuDsu	1.3.6.1.4.1.164.6.1.12.2
radAmcdE1	1.3.6.1.4.1.164.6.1.12.2.1
radAmcdT1	1.3.6.1.4.1.164.6.1.12.2.2
radAce20E	1.3.6.1.4.1.164.6.1.12.2.3
radAce20T	1.3.6.1.4.1.164.6.1.12.2.4
radAce2005	1.3.6.1.4.1.164.6.1.12.2.5
radAce2002	1.3.6.1.4.1.164.6.1.12.2.6
radAce2002E	1.3.6.1.4.1.164.6.1.12.2.7
radAce2E	1.3.6.1.4.1.164.6.1.12.2.8
radAce2T	1.3.6.1.4.1.164.6.1.12.2.9
radMlAtmE1	1.3.6.1.4.1.164.6.1.12.2.10
radMlAtmT1	1.3.6.1.4.1.164.6.1.12.2.11
radAmc102	1.3.6.1.4.1.164.6.1.12.2.12
radAmc102c	1.3.6.1.4.1.164.6.1.12.2.13
radAce202	1.3.6.1.4.1.164.6.1.12.2.14
radAce	1.3.6.1.4.1.164.6.1.12.3
radAce101	1.3.6.1.4.1.164.6.1.12.3.1
radAce102	1.3.6.1.4.1.164.6.1.12.3.2
radAce50	1.3.6.1.4.1.164.6.1.12.3.3
radAce52	1.3.6.1.4.1.164.6.1.12.3.4
radAce52L	1.3.6.1.4.1.164.6.1.12.3.5
radAce201	1.3.6.1.4.1.164.6.1.12.3.7
radAce3200	1.3.6.1.4.1.164.6.1.12.3.8
radAce3100	1.3.6.1.4.1.164.6.1.12.3.9
radAce3400	1.3.6.1.4.1.164.6.1.12.3.10
radAce3402	1.3.6.1.4.1.164.6.1.12.3.11
radAce3100PSN	1.3.6.1.4.1.164.6.1.12.3.12
radAce3200PSN	1.3.6.1.4.1.164.6.1.12.3.13
radAce3400PSN	1.3.6.1.4.1.164.6.1.12.3.14
radAce3402PSN	1.3.6.1.4.1.164.6.1.12.3.15
radAce3600	1.3.6.1.4.1.164.6.1.12.3.16
radAce3205	1.3.6.1.4.1.164.6.1.12.3.17
radAce3105	1.3.6.1.4.1.164.6.1.12.3.18
radSysLA	1.3.6.1.4.1.164.6.1.13
radLA140	1.3.6.1.4.1.164.6.1.13.1
radLA110	1.3.6.1.4.1.164.6.1.13.2
radLA104	1.3.6.1.4.1.164.6.1.13.3
radLA130	1.3.6.1.4.1.164.6.1.13.4
radLA210	1.3.6.1.4.1.164.6.1.13.5
radSysTerminal	1.3.6.1.4.1.164.6.1.100
agnt	1.3.6.1.4.1.164.6.2
STR agnHwVersion	1.3.6.1.4.1.164.6.2.1	DisplayString	read-write	ASCII string for description and display of the agent hardware version, as it is known by the agent software.The user can update the version upon request when he changes components in the agent's module
I32 agnTrapMask	1.3.6.1.4.1.164.6.2.2	Integer32	read-write	The value of this attribute determines the type of traps the agent should mask and not send to the management console. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
OCT agnTrapValue	1.3.6.1.4.1.164.6.2.3	OCTET STRING	read-only	The value of the trap decoded in internal RAD format. Full description is given in the Trap definition file
C32 agnChangeCnt	1.3.6.1.4.1.164.6.2.4	Counter32	read-only	The number of changes in system configuration that were reported to the manager since last cold start
OID agnSpecific	1.3.6.1.4.1.164.6.2.5	OBJECT IDENTIFIER	read-only	Object identifier of entity containing additional information regarding this instance.
OCT agnConfigMsg	1.3.6.1.4.1.164.6.2.6	OCTET STRING	read-only	Full configuration message coded in internal RAD application format. This entry describes agent's configuration. For MP-2200 R3, this object describes agent's support of the V5.1 feature: 1 octet ; bit 0 (LSB). '1' - V5.1 feature is supported '0' - V5.1 feature is not supported.
mngTrapIpTable	1.3.6.1.4.1.164.6.2.7		not-accessible	This table indicates the destination address of the traps. Internally it will be limited to ten addresses.
mngEntry	1.3.6.1.4.1.164.6.2.7.1		not-accessible	An entry in table.
I32 mngID	1.3.6.1.4.1.164.6.2.7.1.1	Integer32	read-only	This value indicates an index of a specific IP address
IP mngIP	1.3.6.1.4.1.164.6.2.7.1.2	IpAddress	read-write	This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.
IP mngIPMask	1.3.6.1.4.1.164.6.2.7.1.3	IpAddress	read-write	This value indicates the mask of the destination addresses of the traps.
I32 mngTrapMask	1.3.6.1.4.1.164.6.2.7.1.4	Integer32	read-write	The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
OCT mngAlarmTrapMask	1.3.6.1.4.1.164.6.2.7.1.5	OCTET STRING	read-write	The value of this object determines the alarm traps that the agent should mask (not send to this manager). The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. For more details on the specific alarm traps masked, see product specification.
U32 mngSnmpTrapUdpPort	1.3.6.1.4.1.164.6.2.7.1.6	Unsigned32	read-write	This variable enables to set the UDP port (socket) used for SNMP traps.
INT agnIndication	1.3.6.1.4.1.164.6.2.8	INTEGER	read-only	Attribute describing the state of the entity the agent is responsible for. In case of a modular entity, the value of this attribute will be according to the component which is in the worst state. The order of severity (from top to bottom) is: critical-> major (or faulty)-> minor-> event-> warning-> normal (off).
INT agnMonitorModeCmd	1.3.6.1.4.1.164.6.2.9	INTEGER	read-write	Setting this attribute to ON, will enforce the agent to change its mode of operation to Monitor Mode
OCT agnLed	1.3.6.1.4.1.164.6.2.10	OCTET STRING	read-only	This entry specifies the LEDs status of the agent module . Each led will be represented by 4 bits where the first 2 bits (left) will specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY)
trapTable	1.3.6.1.4.1.164.6.2.11		not-accessible	This table may include the last few traps generated by the agent, for future retrieval. The table has a limited capacity. If traps are not retrieved in proper time, they will be over-written by new traps. For other devices, it can include generic variables that will be attached to traps as 'accessible-for-notify'.
trapEntry	1.3.6.1.4.1.164.6.2.11.1		not-accessible	An entry in trapTable.
I32 trapID	1.3.6.1.4.1.164.6.2.11.1.1	Integer32	read-only	This object indicates an index of a specific trap. Can be used also for any trap, while trapVal is used as 'accessible-for-notify' or trapNumeric is used.
STR trapVal	1.3.6.1.4.1.164.6.2.11.1.2	DisplayString	read-only	This object is the actual ASCII description of the trap. It can be used also as attached variable of traps, in order to detail in explicit ASCII text, data of the trap. In this case, it is used as 'accessible-for-notify'.
TIK trapTimeSinceOccurrence	1.3.6.1.4.1.164.6.2.11.1.3	TimeTicks	read-only	This object indicates the amount of time passed since the occurrence of the event that triggered this trap.
I32 trapNumeric	1.3.6.1.4.1.164.6.2.11.1.4	Integer32	accessible-for-notify	This object is a numeric general parameter, that can be attached to any trap. Values can be positive or negative.
fileTransfer	1.3.6.1.4.1.164.6.2.12
IP fileServerIP	1.3.6.1.4.1.164.6.2.12.1	IpAddress	read-write	The IP address of the server from which the file is loaded
STR fileName	1.3.6.1.4.1.164.6.2.12.2	DisplayString	read-write	The name of the file to be loaded. For protection, read returns NULL.
INT fileTransCmd	1.3.6.1.4.1.164.6.2.12.3	INTEGER	read-write	The command to be executed on fileName at fileServerIP.
I32 tftpRetryTimeOut	1.3.6.1.4.1.164.6.2.12.4	Integer32	read-write	General Retransmission time-out value (seconds)
I32 tftpTotalTimeOut	1.3.6.1.4.1.164.6.2.12.5	Integer32	read-write	Total Retransmission time-out value (seconds)
INT tftpStatus	1.3.6.1.4.1.164.6.2.12.6	INTEGER	read-write	Status of tftp session. When a session ended with success, the tftpStatus should be endedOk(6). Before restarting a tftp session, the NMS should set the tftpStatus to noOp(2). That's the reason of MAX-ACCESS read-write to this field.
OCT tftpError	1.3.6.1.4.1.164.6.2.12.7	OCTET STRING	read-only	The MSB represents the standard error code. The LSB represents the private error code. 0x0000 is No Error 0x0100 is File Not Found 0x0200 is Access violation 0x0300 is Disk full or allocation exceeded 0x0400 is Illegal TFTP operation 0x0500 is Unknown transfer ID 0x0600 is File already exists 0x0700 is No such user 0x0001 is Server Overflow 0x0002 is No empty UDP port 0x0003 is No empty connection 0x0004 is Illegal File Mode 0x0007 is Illegal PDU size 0x0008 is TFTP Server does not exist 0x0009 is Incorrect File 0x000A is Wrong License format 0x000B is License ID already used
OCT fileTransferToSubSystems	1.3.6.1.4.1.164.6.2.12.8	OCTET STRING	read-write	This object represents the sub-systems the fileTransCmd refers to. It should be used when a system is divided to sub-systems and each sub-system (or part of them) can have a different SW/Configuration. Each bit of this object will represent one of the sub-systems. Bit='1' - APPLY to respective sub-system Bit='0' - DO NOT APPLY to respective sub-system For the meaning of each bit, see product's specification. User will select the sub-systems envolved by filling-in the bits that represent these sub-systems. In this case, the file represented by 'fileName' will include several parts, each representing one of the sub-systems. The agent will refer only to the part/s indicated by this object. 0 Octet Strings = not applicable DEFVAL = 0h for the products that support this object.
STR fileNameWithinProduct	1.3.6.1.4.1.164.6.2.12.9	DisplayString	read-write	The file name used by the product within the product file system.
intSwdlTable	1.3.6.1.4.1.164.6.2.12.10		not-accessible	This parameters table is for internal Software down load. It also includes data about all files contained in the Object from which down-load is performed.
intSwdlEntry	1.3.6.1.4.1.164.6.2.12.10.1		not-accessible	An entry in table.
I32 intSwdlObjIdx	1.3.6.1.4.1.164.6.2.12.10.1.1	Integer32	read-only	The index of the object from which down-load is performed.
I32 intSwdlFileIdx	1.3.6.1.4.1.164.6.2.12.10.1.2	Integer32	read-only	The index of the files included in intSwdlObjIdx. One of these files can be selected to be internally downloaded.
STR intSwdlFileName	1.3.6.1.4.1.164.6.2.12.10.1.3	DisplayString	read-only	The name of the file.
STR intSwdlFileSwVer	1.3.6.1.4.1.164.6.2.12.10.1.4	DisplayString	read-only	The software version of the file.
STR intSwdlSwDate	1.3.6.1.4.1.164.6.2.12.10.1.5	DisplayString	read-only	The software version date of the file.
STR intSwdlSize	1.3.6.1.4.1.164.6.2.12.10.1.6	DisplayString	read-only	The size of the file.
INT intSwdlCmd	1.3.6.1.4.1.164.6.2.12.10.1.7	INTEGER	read-write	The command to down-load a SW file to an object. The Agent will change the value of this MIB object to off(2) automatically, after accepting the command.
OCT intSwdlToSubSystem	1.3.6.1.4.1.164.6.2.12.10.1.8	OCTET STRING	read-write	This object defines the subsystem for download. Bit='1'- APPLY to respective sub system. Bit='0'- DO NOT APPLY to respective sub system. For more details see product specification. For every octet bit0=LSB, bit7=MSB
INT intSwdlCardType	1.3.6.1.4.1.164.6.2.12.10.1.9	INTEGER	read-only	This object defines the Card type that this file is relevant for.
I32 intSwdlFlashIdx	1.3.6.1.4.1.164.6.2.12.10.1.10	Integer32	read-only	The index of the flash memory this file is stored in (1 or 2) (Example: 1= The file is stored in flash No.1). ASMi52 file will always be stored in Flash No.2 (intSwdlFlashIdx=2).
swdlStatusTable	1.3.6.1.4.1.164.6.2.12.11		not-accessible	This parameters table is for software download status. It also includes data about the files down-loaded or attempted to be down-loaded.
swdlStatusEntry	1.3.6.1.4.1.164.6.2.12.11.1		not-accessible	An entry in table.
I32 swdlStatusTypeIdx	1.3.6.1.4.1.164.6.2.12.11.1.1	Integer32	read-only	The index of the down-load type (e.g. external (1) or internal (2)).
I32 swdlStatusIdx	1.3.6.1.4.1.164.6.2.12.11.1.2	Integer32	read-only	The index of the status rows.
STR swdlStatusFileName	1.3.6.1.4.1.164.6.2.12.11.1.3	DisplayString	read-only	The name of the file.
STR swdlStatusSlot	1.3.6.1.4.1.164.6.2.12.11.1.4	DisplayString	read-only	The slot of the updated (or attempted to be updated) object.
STR swdlStatusSubSystem	1.3.6.1.4.1.164.6.2.12.11.1.5	DisplayString	read-only	The subsystem that updated (or attempted to be updated).
I32 swdlStatusStatus	1.3.6.1.4.1.164.6.2.12.11.1.6	Integer32	read-only	The status of the down load process. Value: Fail (2), OK (3), InProcess (4).
STR swdlStatusTime	1.3.6.1.4.1.164.6.2.12.11.1.7	DisplayString	read-only	This MIB parameter indicates the time SW download was finished. The format shuld be YYYY-MM-DD, hh:mm:ss
I32 clearDwldStatusLog	1.3.6.1.4.1.164.6.2.12.12	Integer32	read-write	This object clears the status log. Value: off(2), external(3), internal(4) The Agent will change the value of this MIB object to off(2) automatically, after accepting the command .
autoFileTransfer	1.3.6.1.4.1.164.6.2.12.13
autoFileTransferTable	1.3.6.1.4.1.164.6.2.12.13.1		not-accessible	Scheduling configuration table for Agent initiated file transfer.
autoFileTransferEntry	1.3.6.1.4.1.164.6.2.12.13.1.1		not-accessible	An entry in the table.
INT autoFileTransferType	1.3.6.1.4.1.164.6.2.12.13.1.1.1	INTEGER	read-only	This object defines the type of file to be transferred by agent.
IP autoFileTransferServerIp	1.3.6.1.4.1.164.6.2.12.13.1.1.2	IpAddress	read-write	This object defines the IP Address of the server to which the file is uploaded.
STR autoFileTransferFileName	1.3.6.1.4.1.164.6.2.12.13.1.1.3	SnmpAdminString	read-write	This object defines the name of the file to be uploaded.
INT autoFileTransferScheduling	1.3.6.1.4.1.164.6.2.12.13.1.1.4	INTEGER	read-write	This object defines schedule for TFTP Automatic session(s) initiated by Agent, according to the value selected: now - initiate immediate single session. recurrence- initiate single session 'every M time units'. or 'every N occurrences' or upon both, (earliest event). Time reccurence period (M) is defined by fileTransferTimeRecurrence. Occurrence reccurence (N) is defined by fileTransferOccurrenceRecurrence. Zero value means that the object is not relevant (not taken into account for the recurrence). It is invalid that both will have zero values in our case (recurrence). When both are non zero, file is transferred upon earliest event
I32 autoFileTransferTimeRecurrence	1.3.6.1.4.1.164.6.2.12.13.1.1.5	Integer32	read-write	This object defines time reccurence interval, e.g. M can be 'every M days', 'every M hours' etc. Zero is used to indicate there's no time reccurence (0= notApplicable). This object is taken into account only if autoFileTransferScheduling = recurrence For LA-110 time units are days.
I32 autoFileTransferOccurrenceRecurrence	1.3.6.1.4.1.164.6.2.12.13.1.1.6	Integer32	read-write	This object defines Occurrence reccurence interval, e.g N can be in 'every N alarms', 'every N log entries' etc. zero is used to indicate There's no Event Reccurence. (0= notApplicable) This object is taken into account only if autoFileTransferScheduling = recurrence Occurence Type (Alarms, etc.) is according to autoFileTransferType.
U32 fileTransferServerPort	1.3.6.1.4.1.164.6.2.12.14	Unsigned32	read-write	Server Port number used for File Transfer. Applicable for SFTP. Valid values: 0..65535.
INT fileTransferProtocol	1.3.6.1.4.1.164.6.2.12.15	INTEGER	read-write	File Transfer protocol used.
INT systemReset	1.3.6.1.4.1.164.6.2.13	INTEGER	read-write	Reset action to be performed on the system. - resetMapping - reset SDH/SONET mapping to default for all SDH/SONET links. - resetStandby(6) - can be used only by devices with redundancy on MAIN/CL.
systemTiming	1.3.6.1.4.1.164.6.2.14
STR systemDate	1.3.6.1.4.1.164.6.2.14.1	DisplayString	read-write	System date.
STR systemTime	1.3.6.1.4.1.164.6.2.14.2	DisplayString	read-write	System time.
I32 systemTimeElapsed	1.3.6.1.4.1.164.6.2.14.3	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period. Same for all ports of the device.
systemNtp	1.3.6.1.4.1.164.6.2.14.4
INT systemNtpMode	1.3.6.1.4.1.164.6.2.14.4.1	INTEGER	read-write	This variable represents the NTP Mode.
I32 systemNtpGmt	1.3.6.1.4.1.164.6.2.14.4.2	Integer32	read-write	This variable represents the NTP GMT (Greenwich Mean Time), Possible values range is -12..12. For new devices/versions this variable will be in minutes.
IPt systemNtpServerAddressType	1.3.6.1.4.1.164.6.2.14.4.3	InetAddressType	read-write	This variable represents the NTP Server Address Type.
IP systemNtpServerAddress	1.3.6.1.4.1.164.6.2.14.4.4	InetAddress	read-write	This variable represents the NTP Server Address.
U32 systemNtpUpdateInterval	1.3.6.1.4.1.164.6.2.14.4.5	Unsigned32	read-write	This variable represents the NTP Update Interval, measured in seconds.
INT systemNtpCmd	1.3.6.1.4.1.164.6.2.14.4.6	INTEGER	read-write	This variable represents NTP possible commands. After the Agent accepts a command, it will automatically change the value to off(2).
schedXTable	1.3.6.1.4.1.164.6.2.14.5		not-accessible	An Augment to the Schedule table (schedTable in DISMAN-SCHEDULE-MIB; RFC-3231).
schedXEntry	1.3.6.1.4.1.164.6.2.14.5.1		not-accessible	An entry in the table.
U32 schedYear	1.3.6.1.4.1.164.6.2.14.5.1.1	Unsigned32	read-create	The year during which the scheduled action should take place.
INT schedWeekInMonth	1.3.6.1.4.1.164.6.2.14.5.1.2	INTEGER	read-create	The week in month (schedMonth) during which the scheduled action should take place.
I32 schedParam	1.3.6.1.4.1.164.6.2.14.5.1.3	Integer32	read-create	A Parameter that might be used whenever the scheduled action takes place. For summer-time schedule - This variable represents the time offset (in minutes), meaning: the number of minutes that should be added for summer-time.
systemPort	1.3.6.1.4.1.164.6.2.15
physicalConnectorTable	1.3.6.1.4.1.164.6.2.15.1		not-accessible	This table includes the connector type of ports or interfaces.
physicalConnectorEntry	1.3.6.1.4.1.164.6.2.15.1.1		not-accessible	An entry in table.
I32 portIdx	1.3.6.1.4.1.164.6.2.15.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
INT physicalConnector	1.3.6.1.4.1.164.6.2.15.1.1.2	INTEGER	read-only	The connector of the port/interface. other - none of the specified connectors none - no connector.
INT portOptWaveLength	1.3.6.1.4.1.164.6.2.15.1.1.3	INTEGER	read-only	Wave Length of an Optical interface/port in [nm] and specification if Laser or not. notApplicable - for non-optical ports.
INT portOptMode	1.3.6.1.4.1.164.6.2.15.1.1.4	INTEGER	read-only	Laser Mode of an Optical Laser interface/port. notApplicable - for non-Laser ports.
INT portBalance	1.3.6.1.4.1.164.6.2.15.1.1.5	INTEGER	read-write	This object is according to the port Impedance. For T1 - always balanced. For E1 - there are different impedance values for balanced and unbalanced.
INT portDdmSupport	1.3.6.1.4.1.164.6.2.15.1.1.6	INTEGER	read-only	SFP (Small Form Pluggable) port -support Digital Diagnostics Monitoring.
STR portMfgName	1.3.6.1.4.1.164.6.2.15.1.1.7	SnmpAdminString	read-only	(SFP) Port Manufacturer name (Maximum - 16 characters).
U32 portTypicalMaxRange	1.3.6.1.4.1.164.6.2.15.1.1.8	Unsigned32	read-only	Maximum range supported by SFP port, in meter units.
STR physicalConnectorString	1.3.6.1.4.1.164.6.2.15.1.1.9	SnmpAdminString	read-only	(SFP) connector type. It can be Vendor Specific (unknown in advance). Being a string, the object is not affected by any future new connectors. This object will usually not be used for drawing the connector.
STR portVendorPartNo	1.3.6.1.4.1.164.6.2.15.1.1.10	SnmpAdminString	read-only	SFP Vendor Part Number. Being a string, the object is not affected by any future new SFPs.
prtSupervisory	1.3.6.1.4.1.164.6.2.15.2
prtSpTable	1.3.6.1.4.1.164.6.2.15.2.1		not-accessible	A table.
prtSpEntry	1.3.6.1.4.1.164.6.2.15.2.1.1		not-accessible	Supervisory port parameter table.
I32 prtSupervisoryIndex	1.3.6.1.4.1.164.6.2.15.2.1.1.1	Integer32	read-only	The SP port index. For some products, having modules (cards): The LS byte of the integer is the port index 1..255. The MS byte is different than 0 only if the port belongs to a module. In that case it is the module number. For other products' index see their specification.
INT prtSupervisoryRate	1.3.6.1.4.1.164.6.2.15.2.1.1.2	INTEGER	read-write	This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
INT prtSupervisoryDataBits	1.3.6.1.4.1.164.6.2.15.2.1.1.3	INTEGER	read-write	This attribute indicates the number of data bits in an async frame
INT prtSupervisoryParity	1.3.6.1.4.1.164.6.2.15.2.1.1.4	INTEGER	read-write	This attribute indicates the parity mode in an async frame
INT prtSupervisoryStopBits	1.3.6.1.4.1.164.6.2.15.2.1.1.5	INTEGER	read-write	This attribute indicates the parity mode in an async frame.
INT prtSupervisoryUsage	1.3.6.1.4.1.164.6.2.15.2.1.1.6	INTEGER	read-write	This attribute indicates the usage of the SP port.
INT prtSupervisoryInterface	1.3.6.1.4.1.164.6.2.15.2.1.1.7	INTEGER	read-write	This attribute indicates the supervisory port interface.
INT prtSupervisoryCTS	1.3.6.1.4.1.164.6.2.15.2.1.1.8	INTEGER	read-write	CTS line state.
INT prtSupervisoryDcdDelay	1.3.6.1.4.1.164.6.2.15.2.1.1.9	INTEGER	read-write	DCD delay in msec.
INT prtSupervisoryDSR	1.3.6.1.4.1.164.6.2.15.2.1.1.10	INTEGER	read-write	DSR line state.
INT prtSupervisoryRoutProtocol	1.3.6.1.4.1.164.6.2.15.2.1.1.11	INTEGER	read-write	This attribute indicates the routing protocol of the port. notApplicable - for DP.
prtPerformance	1.3.6.1.4.1.164.6.2.15.3
prtPerfTable	1.3.6.1.4.1.164.6.2.15.3.1		not-accessible	This table includes G.826 ports or interfaces.
prtPerfEntry	1.3.6.1.4.1.164.6.2.15.3.1.1		not-accessible	An entry in table.
I32 prtPerfIdx	1.3.6.1.4.1.164.6.2.15.3.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
INT prtPerfPeriodRef	1.3.6.1.4.1.164.6.2.15.3.1.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. lastPeriod - the period between last two commands of prtPerfSaveAndResetCmd. - If only one command occured since Start-up: the period between Start-up and last command. - If no command occured since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
I32 prtPerfElapsedTime	1.3.6.1.4.1.164.6.2.15.3.1.1.3	Integer32	read-only	Elapsed Time in seconds. - for prtPerfPeriodRef=currentPeriod: The period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. - for prtPerfPeriodRef=lastPeriod: The value of prtPerfElapsedTime when last prtPerfSaveAndResetCmd was received.
I32 prtPerfUAS	1.3.6.1.4.1.164.6.2.15.3.1.1.4	Integer32	read-only	Number of Unavailable Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfES	1.3.6.1.4.1.164.6.2.15.3.1.1.5	Integer32	read-only	Number of Errored Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfSES	1.3.6.1.4.1.164.6.2.15.3.1.1.6	Integer32	read-only	Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfBBE	1.3.6.1.4.1.164.6.2.15.3.1.1.7	Integer32	read-only	Number of Background Block (or Frame) Errors for the reference period (prtPerfPeriodRef).
I32 prtPerfBlocksPerSec	1.3.6.1.4.1.164.6.2.15.3.1.1.8	Integer32	read-only	Blocks per second (or frames per second) of the port/interface indicated by portIdx. This object is constant for a certain port/interface. It is not affected by the prtPerfPeriodRef index.
TIK prtPerfTimeTag	1.3.6.1.4.1.164.6.2.15.3.1.1.9	TimeTicks	read-only	Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was executed. This object is applicable only for prtPerfPeriodRef=lastPeriod. For prtPerfPeriodRef=currentPeriod, the value will always be 0.
INT prtPerfSaveAndResetCmd	1.3.6.1.4.1.164.6.2.15.3.1.1.10	INTEGER	read-write	A command per port/interface, to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. This object is applicable only for prtPerfPeriodRef=currentPeriod. Setting this object to on(3) for prtPerfPeriodRef=last, will cause the agent to return: Bad Value response. When setting validly this object to on(3), agent will perform the required command and will reset automatically the value of this object to off(2). Setting this object to off(2), will do nothing.
prtTest	1.3.6.1.4.1.164.6.2.15.4
prtTestTable	1.3.6.1.4.1.164.6.2.15.4.1		not-accessible	This table includes test data for ports or interfaces.
prtTestEntry	1.3.6.1.4.1.164.6.2.15.4.1.1		not-accessible	An entry in table.
I32 prtTestIdx	1.3.6.1.4.1.164.6.2.15.4.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
I32 prtTestCmdAndStatus	1.3.6.1.4.1.164.6.2.15.4.1.1.2	Integer32	read-write	Setting this object to a value as detailed further on (except 0) will initiate a test on the specific port. The test/s requested will be set according to the respective bit. The value of this object will be a sum of (2**n), where n is the Bit: TEST BIT VALUE ----------- --- ------ reserved 0 1 PayloadLoop=RLB 1 (=Remote Loopback) 2 LineLoop=DIG 2 (=Digital) 4 OtherLoop 3 8 InwardLoop=LLB 4 (=Local Loopback) 16 BERT 5 32 LC 6 64 ToneInjection 7 128 Inband 8 256 BERT Remote (or E1/T1 RLB) 9 512 Downstream-AIS (or E1/T1 LLB) 10 1024 Upstream-AIS 11 2048 Rem-Loop-on-Rem-Unit 12 4096 MacSwapLoop 13 8192 OamETHLoopback 14 16384 OamETHLinkTrace 15 32768 e.g : If the requested value is 20 -> 010100 -> Bits 2 & 4 are set -> the requested tests are : LineLoopback=DIG InwardLoopback=LLB Not all tests combinations are valid. For valid test combination, see each product's specification. For LRS52, only single test is allowed simultaneously The terminology and order of the first tests (except BERT) is according to the one used for Test Status of DS1 and DS3 standards. The notations : RLB, LLB, DIG are the most used in RAD's products, but they can be different. For exact definition see product's spec. Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port. When no test is running on the port, the Get value (test status) will be 0. PayloadLoop=RLB The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. LineLoop=DIG The received signal at this interface does not go through the device (minimum penetration) but is looped back out. OtherLoop Loopbacks that are not defined here. InwardLoop=LLB The sent signal at this interface is looped back through the device. LC This loop is applicable only for HSSI interface, towards the router . ToneInjection This loop is applicable for analog voice (like FXS). Downstream-AIS E1 AIS signal (all ones) is transmitted in the relevant channel toward the STM-1 line. Upstream-AIS E1 AIS signal (all ones) is generated in the relevant channel toward the local received tributary channel output Rem-Loop-on-Rem-Unit Request from far end device to activate remote loopback towards near-end device MacSwapLoop This loop is applicable for ethernet port. Loop is implemented by swapping the MAC addresses of the incoming message. OamETHLoopback Ethernet Loopback is used to verify connectivity of a MEP with a MIP or peer MEP(s) (ITU-T Y.1731, Clause 7.2). OamETHLinkTrace Ethernet Link Trace is an on-demand OAM function which can be used for the two following purposes: - Adjacent Relation Retrieval - Fault Localization (ITU-T Y.1731, Clause 7.3).
I32 prtBertCounter	1.3.6.1.4.1.164.6.2.15.4.1.1.3	Integer32	read-only	This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counter starts from zero (0) anytime BERT is initiated.
INT prtTestInitiator	1.3.6.1.4.1.164.6.2.15.4.1.1.4	INTEGER	read-only	This object indicates who initiated this port's test/s.
I32 prtTestTimeout	1.3.6.1.4.1.164.6.2.15.4.1.1.5	Integer32	read-write	This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. For RICi-E1T1, RICi-E3T3 the measurement unit is in seconds. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever
INT prtTestVctRxResult	1.3.6.1.4.1.164.6.2.15.4.1.1.6	INTEGER	read-only	This object indicates the result of the Vct on the cable connected to the RX connector.
INT prtTestVctTxResult	1.3.6.1.4.1.164.6.2.15.4.1.1.7	INTEGER	read-only	This object indicates the result of the Vct on the cable connected to the TX connector.
I32 prtTestVctRxDistance	1.3.6.1.4.1.164.6.2.15.4.1.1.8	Integer32	read-only	This object indicates the distance in Meters to the RX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
I32 prtTestVctTxDistance	1.3.6.1.4.1.164.6.2.15.4.1.1.9	Integer32	read-only	This object indicates the distance in Meters to the TX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
INT prtTestVctCmd	1.3.6.1.4.1.164.6.2.15.4.1.1.10	INTEGER	read-write	Vct command. on (3) = Start Vct on both cables connected to RX and TX connectors of this port. Agent will perform the required command and change automatically the value of this object to off(2).
I32 prtTestVctRxCrossPair	1.3.6.1.4.1.164.6.2.15.4.1.1.11	Integer32	read-only	This object should be equal to the Index (prtTestIdx) of the Rx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair. This object was especially created for ETX-202. Currently not in use.
I32 prtTestVctTxCrossPair	1.3.6.1.4.1.164.6.2.15.4.1.1.12	Integer32	read-only	This object should be equal to the Index (prtTestIdx) of the Tx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.
U32 prtTestActivationDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.13	Unsigned32	read-write	This object is applicable only when a single test is running. It indicates test activation delay in seconds. A Value of 0 indicates that the test starts immediately.
INT prtTestMacSwapLoopDataMode	1.3.6.1.4.1.164.6.2.15.4.1.1.14	INTEGER	read-write	This object defines which part of the data will be looped back.
I32 prtTestMacSwapLoopVlanId	1.3.6.1.4.1.164.6.2.15.4.1.1.15	Integer32	read-write	This object specifies the VLAN ID for prtTestMacSwapLoopDataMode=specificVlan.
INT prtTestMacSwapLoopDirection	1.3.6.1.4.1.164.6.2.15.4.1.1.16	INTEGER	read-write	This object defines the direction of the performed loopback. In ETX102 'local' corresponds to Ingress loop (either on User port or on Network port), and 'remote' corresponds to Egress loop (either on User port or on Network port).
MAC prtTestMacSwapLoopDestAddr	1.3.6.1.4.1.164.6.2.15.4.1.1.17	MacAddress	read-write	Configures the MAC address that will be sent in the Destination field of the packet in the outgoing direction.
MAC prtTestMacSwapLoopSrcAddr	1.3.6.1.4.1.164.6.2.15.4.1.1.18	MacAddress	read-write	Configures the MAC address that will be sent in the Source field of the packet in the outgoing direction.
U32 prtTestOamMinRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.19	Unsigned32	read-only	The mininal value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamMaxRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.20	Unsigned32	read-only	The maximum value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamAvgRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.21	Unsigned32	read-only	The average round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamTxInterval	1.3.6.1.4.1.164.6.2.15.4.1.1.22	Unsigned32	read-write	Indicates the interval between loopback sent messages.Units are msec.
IP prtTestDestinationIpAddress	1.3.6.1.4.1.164.6.2.15.4.1.1.23	IpAddress	read-write	Indicates the destination IP Address in the transmitted messages that are looped back.
U32 prtTestTTL	1.3.6.1.4.1.164.6.2.15.4.1.1.24	Unsigned32	read-write	Time-to-live.Number of hops the loopback message will go through the net before deciding to discard it.
U32 prtTestBwProfile	1.3.6.1.4.1.164.6.2.15.4.1.1.25	Unsigned32	read-write	Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test in order to limit the traffic that is looped back.
prtParam	1.3.6.1.4.1.164.6.2.15.5
prtParamTable	1.3.6.1.4.1.164.6.2.15.5.1		not-accessible	This table includes general port parameters. The meaning is different for every product that supports it due to a general parameter - prtControlCnfg. For ACE2002: -This table is used as a mechanism to create the next interface index. The algorithm description: The NMS will send the agent the following get command: get(nextIfIndex.index), where index=interface on which the new index is dependent on. Upon this command the agent will generate and return the new index to the NMS. - This table is partially supported according to the interface type. Upon getNext function the irrelevant parameters will be skipped.
prtParamEntry	1.3.6.1.4.1.164.6.2.15.5.1.1		not-accessible	An entry in table.
I32 prtParamIdx	1.3.6.1.4.1.164.6.2.15.5.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. For ACE2002: This parameter is the physical layer ifIndex of the slot on which the NMS requires the next interface index.
I32 prtControlCnfg	1.3.6.1.4.1.164.6.2.15.5.1.1.2	Integer32	read-write	This object may be used for port RW general parameter/s. For detailed meaning, see product's spec. Supported by: PRBi-E3/T3. For ACE2002: This parameter will include the value of the new index generated by agent. For Optimux-T3 and OP-155-1: This parameter will be used for Release Remote LLB Command: on=2= Set value only. Command to release LLB of Remote Unit. Agent will return automatically to 'off' value after performing the command. off=3=Get value only. For LA140 This parameter will be used as EchoCanceler per timeslot off = 2 Echo Canceler is disabled on = 3 Echo Canceler is enabled For FCD-155 This parameter will be used to select the port that is clock source for a PDH port, For E1/T1 PDH VC12/VT1.5 = 2 SDH/SONET = 3 For E3/T3 PDH VC3/DS3 = 2 SDH/SONET = 3 For ACE-52 This parameter will be used as Transmit Frame Type, i.e. which type of frame the corresponding bridge port will transmit: Untagged = 2 Tagged = 3 .
INT prtParamClkSrc	1.3.6.1.4.1.164.6.2.15.5.1.1.3	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' or 'loopback' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' or 'internal' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' or 'external' indicates that recovered receive clock from another card or interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'master' and 'fallback' values may be used RO to indicate active clock. 'station' - indicate clock received from station port is used as transmit clock.
INT prtParamPhantom	1.3.6.1.4.1.164.6.2.15.5.1.1.4	INTEGER	read-write	Power feeding to another device.
INT prtParamResetStatsCmd	1.3.6.1.4.1.164.6.2.15.5.1.1.5	INTEGER	read-write	Reset statistics of the selected port.
TIM prtParamLastResetStatsTime	1.3.6.1.4.1.164.6.2.15.5.1.1.6	TimeStamp	read-only	The value of MIB II's sysUpTime object at the last time that prtParamResetStatsCmd was Set to on(3) for this port. If prtParamResetStatsCmd was never Set to on(3) since last re-initialization of the agent, then this object contains a zero value. This object enables calculating the running time of Statistics counters for this port, by: [sysUpTime-prtParamLastResetStatsTime]. For some devices other types of 'Reset' may affect this parameter
INT prtParamInterfaceType	1.3.6.1.4.1.164.6.2.15.5.1.1.7	INTEGER	read-write	The type of the port.
INT prtParamClearAlarm	1.3.6.1.4.1.164.6.2.15.5.1.1.8	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Port Alarms. Upon completion, the value will automatically change to off(2).
OCT prtParamLeds	1.3.6.1.4.1.164.6.2.15.5.1.1.9	OCTET STRING	read-only	This entry specifies the LEDs status of the port. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
INT prtParamLineLength	1.3.6.1.4.1.164.6.2.15.5.1.1.10	INTEGER	read-write	Line Length of the line connected to this port.
INT prtParamUsage	1.3.6.1.4.1.164.6.2.15.5.1.1.11	INTEGER	read-write	Defines whether this port works as User port or as Network port.
INT prtParamMappingMode	1.3.6.1.4.1.164.6.2.15.5.1.1.12	INTEGER	read-write	This object defines path protection on SONET/SDH link Auto - SONET/SDH mapping for port is copied automatically to same TU on the redundant SONET/SDH local (reside on same slot) link by agent. Manual - the user can configure the redundant mapping for port on the same link or to the other link on any TU Adjacent - similar to auto, but mapping is copied automatically by agent to link on adjacent slot .
INT prtParamAlarmIndication	1.3.6.1.4.1.164.6.2.15.5.1.1.13	INTEGER	read-only	This object indicates status-aggregation of non-masked alarms associated with all interface layers, related to this physical port. When at least one non-masked alarm exists on any layer, value of this object is on (3). Indication will be off (2) only when there's no active non-masked alarm on any interface layer related to this port. Masking an Alarm, will consider it as not exist for this indication. Example: When a port has an ATM higher layer and at least one VC has alarm, value of this object will be on (3)
OCT prtParamClkQualityLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.14	OCTET STRING	read-only	This parameter indicates quality level of clock signal. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows (when bit1=0): Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit)- Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization) 0001 PRS (=ST1 = Stratum 1 Traceable) 0111 ST2 (Stratum 2 Traceable) 1010 ST3 (Stratum 3 Traceable) 1100 SMC (SONET Minimum Clock Traceable) 1101 Stratum 3E Traceable bit1 = '1' - indicates all octet is Not Applicable
INT prtParamClkWaveShape	1.3.6.1.4.1.164.6.2.15.5.1.1.15	INTEGER	read-write	Wave shape of station clock source signal.
INT prtParamStatus	1.3.6.1.4.1.164.6.2.15.5.1.1.16	INTEGER	read-only	Station clock source Status.
I32 prtParamSignalLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.17	Integer32	read-only	This object indicates signal level (in thenth of dB units) on selected port.
OCT prtParamClkUserQualityLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.18	OCTET STRING	read-write	This parameter allows user to mark quality level of clock. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows: Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit) Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization)
U32 prtParamDataRate	1.3.6.1.4.1.164.6.2.15.5.1.1.19	Unsigned32	read-write	Rate of serial data port (V.11, V.24, V.35) in kbps units.
INT prtParamLoopDetect	1.3.6.1.4.1.164.6.2.15.5.1.1.20	INTEGER	read-write	Enable/disable Loop Detection on a port. Examples of ports: physical, Channelized Bundle over TDM Uplink, Bridge Ports.
OCT prtParamActUponLoopDetect	1.3.6.1.4.1.164.6.2.15.5.1.1.21	OCTET STRING	read-write	This parameter is used to indicate which actions should be taken in case a loop is detected in the network the port is part of. Each action is represented by a bit. Currently defined (for RIC155GE/RIC622GE): Bit 0 - Transmit Shut Down Bit 1 - Forward Alarms If bit value = '1' then the action is taken. If bit value = '0' then the actions is not taken.
INT prtParamPSNLayer	1.3.6.1.4.1.164.6.2.15.5.1.1.22	INTEGER	read-write	This object indicates the network layer from which clock is derived.
INT prtParamRxSsm	1.3.6.1.4.1.164.6.2.15.5.1.1.23	INTEGER	read-write	This object indicates if Station Clock SSM messages received will serve as criteria for clock selection.
INT prtParamClkSsmRxSource	1.3.6.1.4.1.164.6.2.15.5.1.1.24	INTEGER	read-write	This object indicates the Sa-bit of the E1 frame, in which SSM messages are carried.
U32 prtParamFarEndDevice	1.3.6.1.4.1.164.6.2.15.5.1.1.26	Unsigned32	read-write	Programmed Far-End device connected to this port. This object is relevant for products having multiple DBs. It will enable configuring offline, the relevant data. For MP-4100, LRS-102 OP-108/106 cards, the options will be: 1 = None (when a port is not connected to any remote device) 2 = OP-108 3 = OP-108/ETH 4 = OP-106 5 = OP-106/ETH 6 = card of MP or LRS-102
INT prtParamTxClk	1.3.6.1.4.1.164.6.2.15.5.1.1.27	INTEGER	read-write	enable/disable station clock signal output.
prtIP	1.3.6.1.4.1.164.6.2.15.6
prtIpParamTable	1.3.6.1.4.1.164.6.2.15.6.1		not-accessible	A table - Parameters for IP Ports.
prtIpParamEntry	1.3.6.1.4.1.164.6.2.15.6.1.1		not-accessible	An entry in table.
I32 prtIpParamConfigIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.1	Integer32	read-only	This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). For products having Agent and Edit configurations, Write operation for the table entries is allowed only to Config=255.
I32 prtIpParamSlotIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.2	Integer32	read-only	This object indicates a unique number of the slot position in which the module is inserted. notApplicable = 255 (for products that don't have slots). For KM: kmxMlA (103), kmxMlB (104).
I32 prtIpParamIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.3	Integer32	read-only	This object indicates a unique Port Index.
IP prtIpParamHostIP	1.3.6.1.4.1.164.6.2.15.6.1.1.4	IpAddress	read-write	The host interface IP address.
IP prtIpParamHostMask	1.3.6.1.4.1.164.6.2.15.6.1.1.5	IpAddress	read-write	The host interface subnet mask.
IP prtIpParamDefaultGateway	1.3.6.1.4.1.164.6.2.15.6.1.1.6	IpAddress	read-write	Default Gateway's IP Address.
INT prtIpParamMediaMode	1.3.6.1.4.1.164.6.2.15.6.1.1.7	INTEGER	read-only	This object indicates the real Media Mode.
INT prtIpParamMediaRate	1.3.6.1.4.1.164.6.2.15.6.1.1.8	INTEGER	read-only	This object indicates the real Media Rate (Mbps).
INT prtIpParamMngVlanSupport	1.3.6.1.4.1.164.6.2.15.6.1.1.9	INTEGER	read-write	Management VLAN support (Tagging). no - No support of VLAN Tagging. yes - 4 VLAN bytes will be added to the frame.
I32 prtIpParamMngVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.10	Integer32	read-write	Management VLAN ID.
I32 prtIpParamMngVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.11	Integer32	read-write	Management VLAN Frame priority.
INT prtIpParamRingMode	1.3.6.1.4.1.164.6.2.15.6.1.1.12	INTEGER	read-write	This object indicates If Ring Mode is enabled or not.
INT prtIpParamProtIpEnable	1.3.6.1.4.1.164.6.2.15.6.1.1.13	INTEGER	read-write	This object indicates whether a list of Protected IP Addresses is enabled or not. This object is applicable only if prtIpParamRingMode=enable.
INT prtIpParamTrafficPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.14	INTEGER	read-write	This object indicates the traffic priority of this port.
IP prtIpParamRemoteIP	1.3.6.1.4.1.164.6.2.15.6.1.1.15	IpAddress	read-write	This is the IP Address of the remote device that is connected to the current device (Point to Point Application). It is used for sending OAM packets on the LAN to the remote side in order to check that the connection is OK.
INT prtIpParamMaxTxBandwidth	1.3.6.1.4.1.164.6.2.15.6.1.1.16	INTEGER	read-write	This object shows the Max Bandwidth allowed on the LAN. Full - means that a Maximum of 100 Mega Byte Rate may go through the LAN. e1(3) means that the maximum is an E1 rate. t1(4) is for a maximum of a T1 rate.
I32 prtIpParamTos	1.3.6.1.4.1.164.6.2.15.6.1.1.17	Integer32	read-write	TOS = Type of Service transmitted. Valid values: 0..255.
INT prtIpParamConnect	1.3.6.1.4.1.164.6.2.15.6.1.1.18	INTEGER	read-write	Port Connection.
I32 prtIpParamAgingTime	1.3.6.1.4.1.164.6.2.15.6.1.1.19	Integer32	read-write	Aging Time in seconds.
INT prtIpParamEncapsulationProt	1.3.6.1.4.1.164.6.2.15.6.1.1.20	INTEGER	read-write	Encapsulation Protocol.
I32 prtIpParamEncapProtPort	1.3.6.1.4.1.164.6.2.15.6.1.1.21	Integer32	read-write	Encapsulation Protocol Port (TCP/UDP Port).
INT prtIpParamVlanSupport	1.3.6.1.4.1.164.6.2.15.6.1.1.22	INTEGER	read-write	VLAN support (Tagging). 'no' - No support of VLAN Tagging. 'yes' - 4 VLAN bytes will be added to the frame.
I32 prtIpParamVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.23	Integer32	read-write	VLAN Identifier.
I32 prtIpParamVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.24	Integer32	read-write	VLAN Frame priority.
I32 prtIpParamDoubleTagVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.25	Integer32	read-write	VLAN Identifier of the Double Tagging VLAN.
I32 prtIpParamDoubleTagVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.26	Integer32	read-write	VLAN Frame priority of the Double Tagging VLAN.
INT prtIpParamVlanTagging	1.3.6.1.4.1.164.6.2.15.6.1.1.27	INTEGER	read-write	VLAN Tagging. 'unmodified' - No change will be done to the Frame. 'tag' - Add Tag to Untagged Frames. 'doubleTag' - Add Tag to all Frames. 'doubleTagAndFallBack' - Double Tagging will have different rules for VLANs that this port is member in, than these it is not a member in. 'untag' - Remove Tag from tagged frames.
I32 prtIpParamRateLimit	1.3.6.1.4.1.164.6.2.15.6.1.1.28	Integer32	read-write	The maximum rate permitted to transfer via this port, in Kbps.
I32 prtIpParamDefInterface	1.3.6.1.4.1.164.6.2.15.6.1.1.29	Integer32	read-write	The Default Interface for packets with unresolved destination subnet. For internal-X port: 100 + X .
INT prtIpParamMng	1.3.6.1.4.1.164.6.2.15.6.1.1.30	INTEGER	read-write	This object indicates whether Management is enabled/disabled via this port.
I32 prtIpParamFloodedRateLimit	1.3.6.1.4.1.164.6.2.15.6.1.1.31	Integer32	read-write	The maximum rate permitted to transfer broadcast, multicast, and unicast flooded frames via this port, in Kbps. 0 - Disable. In Ipmux14 this parameter is applicable when prtIpParamRateLimit=0 (disable).
U32 prtIpParamBurstSize	1.3.6.1.4.1.164.6.2.15.6.1.1.32	Unsigned32	read-write	The burst size that the port can support beyond rate limitation determined in prtIpParamRateLimit. Burst Size is measured in bytes.
INT prtIpParamLimitPacketType	1.3.6.1.4.1.164.6.2.15.6.1.1.33	INTEGER	read-write	The packet type that will be rate limited. Rate limitation determined in prtIpParamRateLimit. all - All packet types are rate limited. broadMultiFloodedUnicast - Broadcast, Multicast and Flooded Unicast packets are rate limited. broadcastMulticast - Broadcast and Multicast packets are rate limited. broadcast - Broadcast packets are rate limited.
I32 prtIpParamKeepAliveInterval	1.3.6.1.4.1.164.6.2.15.6.1.1.34	Integer32	read-write	This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
I32 prtIpParamKeepAliveThresh	1.3.6.1.4.1.164.6.2.15.6.1.1.35	Integer32	read-write	This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
I32 prtIpParamP2pKeepAliveVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.36	Integer32	read-write	Dedicated VLAN ID for keep alive messages.
I32 prtIpParamP2pKeepAliveVlanPrio	1.3.6.1.4.1.164.6.2.15.6.1.1.37	Integer32	read-write	VLAN priority for P2P keep alive messages .
MAC prtIpParamRingAdjacentMacAddr	1.3.6.1.4.1.164.6.2.15.6.1.1.38	MacAddress	read-only	The MAC address of the adjacent NE connected to this port in an ETH ring. If the port is not a member of a ring, the value of this parameter will be 00-00-00-00-00-00.
prtClkSrc	1.3.6.1.4.1.164.6.2.15.7
prtClkSrcTable	1.3.6.1.4.1.164.6.2.15.7.1		not-accessible	A table - Parameters for master and fallback clock source of ports .
prtClkSrcEntry	1.3.6.1.4.1.164.6.2.15.7.1.1		not-accessible	An entry in table.
I32 prtClkSrcCnfgIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
I32 prtClkSrcPrtIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index (receiving clock). Refer to device specification for port Index
INT prtClkSrcIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.3	INTEGER	not-accessible	An index in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
INT prtClkSrcMode	1.3.6.1.4.1.164.6.2.15.7.1.1.4	INTEGER	read-write	This entry indicates the source the nodal timing is locked to.
I32 prtClkSrcPrt	1.3.6.1.4.1.164.6.2.15.7.1.1.5	Integer32	read-write	This entry is valid only when working in rxClk mode. It specifies the port from which the clock willl be taken. Refer to device specification for source port Index
opticalPort	1.3.6.1.4.1.164.6.2.15.8
optPrtMonitorTable	1.3.6.1.4.1.164.6.2.15.8.1		not-accessible	A table - optical port (e.g SFP) monitoring parameters, according to SFF-8472 Specification for Diagnostic Monitoring Interface for Optical Xcvrs. and ITU-T rec. G.958
optPrtMonitorEntry	1.3.6.1.4.1.164.6.2.15.8.1.1		not-accessible	An entry in table.
I32 optPrtMonitorPrtIdx	1.3.6.1.4.1.164.6.2.15.8.1.1.1	Integer32	not-accessible	This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
INT optPrtMonitorSample	1.3.6.1.4.1.164.6.2.15.8.1.1.2	INTEGER	not-accessible	This index indicates historic and current values - minimum, maximum and actual (current) value.
I32 optPrtMonitorTxPower	1.3.6.1.4.1.164.6.2.15.8.1.1.3	Integer32	read-only	Transmitted optical power level. Value is given in units of hundredth (1/100) of dBm.
I32 optPrtMonitorLaserBias	1.3.6.1.4.1.164.6.2.15.8.1.1.4	Integer32	read-only	LASER bias current level. Value is given in units of microAmper (uA).
I32 optPrtMonitorLaserTemp	1.3.6.1.4.1.164.6.2.15.8.1.1.5	Integer32	read-only	LASER temperature level, in hundredth (1/100) (C) degrees.
I32 optPrtMonitorRxPower	1.3.6.1.4.1.164.6.2.15.8.1.1.6	Integer32	read-only	Received optical power in units of hundredth (1/100) of dBm.
I32 optPrtMonitorSupplyVoltage	1.3.6.1.4.1.164.6.2.15.8.1.1.7	Integer32	read-only	Supply voltage, in hundredth (1/100) of volts (V).
optPrtCnfgTable	1.3.6.1.4.1.164.6.2.15.8.2		not-accessible	A table - optical port configuration
optPrtCnfgEntry	1.3.6.1.4.1.164.6.2.15.8.2.1		not-accessible	An entry in table.
U32 optPrtCnfgIdx	1.3.6.1.4.1.164.6.2.15.8.2.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.x.
U32 optPrtCnfgPrtIdx	1.3.6.1.4.1.164.6.2.15.8.2.1.2	Unsigned32	not-accessible	This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
INT optPrtCnfgALS	1.3.6.1.4.1.164.6.2.15.8.2.1.3	INTEGER	read-write	enable/disable Automatic Laser Shutdown
INT systemResetAllStatsCmd	1.3.6.1.4.1.164.6.2.16	INTEGER	read-write	Reset statistics of all ports and connections of the device.
INT systemClearTablesCmd	1.3.6.1.4.1.164.6.2.17	INTEGER	read-write	tempCnfgTables - Set RowStatus = destroy for all entries of some tables having RowStatus object, for temporary configuration only! (255). For the relevant tables, see product's specification. This object should be used by WAN product applications before performing the Update operation, in order to clear old entries of these tables. For MP-104/204 the entries will be destroyed for cnfg=1. off - agent will automatically change to this value, after performing the command.
I32 systemParameter	1.3.6.1.4.1.164.6.2.18	Integer32	read-write	This parameter can be used for different purposes: - TELNET session time-out in seconds. - Ace20: when trying to create row in a table that already has row with the same values, if set of values has to be unique in table, this attribute is set to the index of the existing row. - Optimux-T3: when CH interfaces are RJ-45, user can select via this object, the interface type for each Group of channels: T1 or E1: The selection will be a sum of the following Bits. '0' = T1 '1' = E1 Bit Group Value for each Bit having '1' 1 1 (CH-1..CH-8) 1 2 2 (CH-9..CH-12) 2 3 3 (CH-13..CH-20) 4 4 4 (CH-21..CH-28) 8 Examples: 15 = all Groups are selected to be E1 6 = Group 2 and Group 3 are selected to be E1 (Group 1 and Group 4 are T1). - FCD-A, FCD-M: user can select via this object the configuration used for Get values of MSDSL parameters that don't have configuration index. 1 =active configuration 255=temporary configuration. Set of this object should be done before Getting the MSDSL RW parameters. - Ace2002: This parameter indicates the number of intervals that were successfully uploaded upon statistics collection session. - FCD-IP, WR, FCD-IPD, LA-240: This parameter indicates whether Telnet Access is enabled/disabled: Values: 2 - Telnet Access is Disabled. 3 - Telnet Access is Enabled. -Vmux-110: This parameter value equals to maximum number of bundles. -Optimux-155: Simmilar usage to Optimux T3. user can select via this object, interface type T1 or E1 for each Group of channels (LIU): LIU group consists of 7 channels. Up to 12 LIUs are represented (84 T1 Channels). The selection will be a sum of the 2**n For each bit:'0' = T1 ,'1' = E1 Bit Group 1 1 (CH-1 .. CH-7) 2 2 (CH-8 .. CH-14) 3 3 (CH-15 ..CH-21) ... 9 9 (CH-56.. CH-63) ... 10 10 (CH-64..CH-70) 11 11 (CH-71..CH-77) 12 12 (CH-78..CH-84)
OCT agnGlobalAlarmMask	1.3.6.1.4.1.164.6.2.19	OCTET STRING	read-write	The value of this attribute determines the alarm traps the agent should mask and not send to the managers. Each bit from a certain octet represents a certain alarm.
INT alarmSeverity	1.3.6.1.4.1.164.6.2.20	INTEGER	read-only	This object specifies the severity of the alarms.
INT alarmState	1.3.6.1.4.1.164.6.2.21	INTEGER	read-only	.
INT agnTestStatus	1.3.6.1.4.1.164.6.2.22	INTEGER	read-only	Indicates the current test status (for all levels: system, card, port). This attribute will be set to: on(3): when there is at least one test in progress on the system/card/port off(2): when there is NO test in progress on the system/card/port
INT systemSaveAndResetAllStatsCmd	1.3.6.1.4.1.164.6.2.23	INTEGER	read-write	on - a command to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. off - agent will automatically change to this value, after performing the command.
IP systemDefaultGateway	1.3.6.1.4.1.164.6.2.24	IpAddress	read-write	Default Gateway's IP Address.
systemPsTable	1.3.6.1.4.1.164.6.2.25		not-accessible	This table describes the PS types of a device. Usage of this table is specified in the device's NMS SRS
systemPsEntry	1.3.6.1.4.1.164.6.2.25.1		not-accessible	An entry in table.
I32 systemPsIndex1	1.3.6.1.4.1.164.6.2.25.1.1	Integer32	read-only	First Index. In HUBs: 1 = PS-A slot 2 = PS-B slot 3 = PS-C slot. In SA units: 1 = PS1 2 = PS2 Default = 1
I32 systemPsIndex2	1.3.6.1.4.1.164.6.2.25.1.2	Integer32	read-only	Second Index. In HUBs: 1 always. In SA units: 1 = Local 2 = Remote Default = 1.
INT systemPsType	1.3.6.1.4.1.164.6.2.25.1.3	INTEGER	read-only	The type of PS, for a stand-alone product. acDc - PS that supports both AC and DC. acPF - Power Feeding (phantom) box that is feeding another box by external AC. dcPF - Power Feeding (phantom) box that is feeding another box by external DC.
INT systemPsStatus	1.3.6.1.4.1.164.6.2.25.1.4	INTEGER	read-only	The Status of the PS unit.
INT systemPsHotSwap	1.3.6.1.4.1.164.6.2.25.1.5	INTEGER	read-only	Is PS unit hot swap or fixed.
OCT agnFans	1.3.6.1.4.1.164.6.2.26	OCTET STRING	read-only	This entry specifies the FANs existence and status. Each fan will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each fan: 00 - FAN does not exist 01 - FAN exists and OK (Low Mode) 10 - High Mode (FAN OK) 11 - FAN exists and is Failed bits 0-1 are for first fan bits 2-3 are for 2nd fan (if exists) bits 4-5 are for 3nd fan (if exists) bits 6-7 are for 4nd fan (if exists) bits 8-9 are for 5nd fan (if exists) bits 10-11 are for 6nd fan (if exists) bits 12-13 are for 7nd fan (if exists) bits 14-15 are for 8nd fan (if exists).
I32 agnSendTrapParameter	1.3.6.1.4.1.164.6.2.27	Integer32	read-write	This object specifies if the agent will attach a specific parameter to a trap. For ACE2002 the agent will attach or not the openViewSeverity parameter according to the value of this parameter: 1 - will attach openViewSeverity. 0 - will not attach openViewSeverity.
OCT agnSensorsStatus	1.3.6.1.4.1.164.6.2.28	OCTET STRING	read-only	This entry specifies the Sensors (Temperature sensors or others) existence and status. Each sensor will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each sensor: 00 - sensor does not exist 01 - sensor exists and status is OK 11 - sensor exists and status is not OK ( e.g. temperature exceeds pre-defined threshold) bits 0-1 are for first sensor bits 2-3 are for 2nd sensor (if exists) and so on... Bit 0 is the LSB.
INT agnStationClockCard	1.3.6.1.4.1.164.6.2.29	INTEGER	read-only	This entry specifies the station clock card existence and status. notExist - station clock card (piggy) does not exist. notValid - station clock card exists but clock status is not valid. ok - station clock card exists, and its status is OK When the sepcific reason for clock status not being valid is known, it may be reported by lossOfSync or lossOfSignal values.
I32 xcIndexNext	1.3.6.1.4.1.164.6.2.30	Integer32	read-only	This object contains an appropriate value to be used for xcIndex when creating entries in the xcTable. The value 0 indicates that no unassigned entries are available. To obtain the xcIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
xcTable	1.3.6.1.4.1.164.6.2.31		not-accessible	Configuration of system cross-connect entries. The table follows the behavior described in RFC 2515, RFC 1604 regarding the creation deletion and modification of an entry within the table.
xcEntry	1.3.6.1.4.1.164.6.2.31.1		not-accessible	An entry in table.
I32 xcIndex	1.3.6.1.4.1.164.6.2.31.1.1	Integer32	not-accessible	Cross Connect Identifier.
I32 xcIfIndex1	1.3.6.1.4.1.164.6.2.31.1.2	Integer32	not-accessible	The interface Index from the ifTable, which identify one side of the connection.
I32 xcVpi	1.3.6.1.4.1.164.6.2.31.1.3	Integer32	not-accessible	The VPI value.
I32 xcVci	1.3.6.1.4.1.164.6.2.31.1.4	Integer32	not-accessible	The VCI value.
I32 xcIfIndex2	1.3.6.1.4.1.164.6.2.31.1.5	Integer32	not-accessible	The interface Index from the ifTable, which identifies the other side of the connection.
ROW xcRowStatus	1.3.6.1.4.1.164.6.2.31.1.6	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table.
STR xcDescr	1.3.6.1.4.1.164.6.2.31.1.7	DisplayString	read-create	A textual string containing information about the xc entry.
INT xcAdminStatus	1.3.6.1.4.1.164.6.2.31.1.8	INTEGER	read-create	The desired administrative status of this bi-directional cross-connect.
INT xcOperStatus	1.3.6.1.4.1.164.6.2.31.1.9	INTEGER	read-only	The operational status of this bi-directional cross-connect.
INT xcAttachedIfType	1.3.6.1.4.1.164.6.2.31.1.10	INTEGER	read-only	This object indicates if the specific VCC is already attached to any interface, and indicates the type of the interface. This object's purpose is to ease the checking to the NMS. notApplicable - used for entries that are not LAN (as HDLC), or when the VCC was attached to a bridge, or when this parameter is irrelevant. free - the LAN VCC wasn't attached yet to any router interface. routerAtm - attached to an ATM router interface. lis - attached to a LIS interface.
I32 xcInputPriority	1.3.6.1.4.1.164.6.2.31.1.11	Integer32	read-create	This object is the priority, by which the LAN frames will be internaly sent to the ATM HW. This parameter is applicable if atmNteMdlInputPriorityMechanism=enabled. 1 - Highest priority. Will be the first to be sent to the ATM HW. 4 - Lowest priority. Will be the last to be sent to the ATM HW.
I32 xcBitMapping	1.3.6.1.4.1.164.6.2.31.1.12	Integer32	read-only	This object maps this entry to a bit of an octet string. For ACE2002 this object maps the LAN VCC to the bit of the VLAN Port Lists. If the value is '0' then it means that this VCC is not mapped to a port list or it may be an HDSL entry.
systemModule	1.3.6.1.4.1.164.6.2.32
modlParam	1.3.6.1.4.1.164.6.2.32.1
modlParamTable	1.3.6.1.4.1.164.6.2.32.1.1		not-accessible	This table include parameters for system modules.
modlParamEntry	1.3.6.1.4.1.164.6.2.32.1.1.1		not-accessible	An entry in table.
I32 modlParamIndex	1.3.6.1.4.1.164.6.2.32.1.1.1.1	Integer32	read-only	The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4.
INT modlParamReset	1.3.6.1.4.1.164.6.2.32.1.1.1.2	INTEGER	read-write	Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2).
INT modlParamSwdlStatus	1.3.6.1.4.1.164.6.2.32.1.1.1.3	INTEGER	read-only	This parameter indicates whatever the swdl is in process or not.
OCT modlParamLeds	1.3.6.1.4.1.164.6.2.32.1.1.1.4	OCTET STRING	read-only	This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
INT modlParamType	1.3.6.1.4.1.164.6.2.32.1.1.1.5	INTEGER	read-only	This attribute indicates the Module Type.
STR modlParamSwVer	1.3.6.1.4.1.164.6.2.32.1.1.1.6	DisplayString	read-only	This attribute indicates the Module's Software Version.
INT agnNearFarConnection	1.3.6.1.4.1.164.6.2.33	INTEGER	read-only	This parameter describes the connection between near-end and far-end agents.
agnAccess	1.3.6.1.4.1.164.6.2.34
INT agnTelnetAccess	1.3.6.1.4.1.164.6.2.34.1	INTEGER	read-write	Enable/Disable accessing the device via Telnet. disable - no one will be allowed to access the device via Telnet. enable - all users are allowed Telnet Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSH) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSH).
INT agnWebAccess	1.3.6.1.4.1.164.6.2.34.2	INTEGER	read-write	Enable/Disable accessing the device via Web. disable - no one will be allowed to access the device via Web. enable - all users are allowed Web Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSL) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSL).
INT agnRadiusAccess	1.3.6.1.4.1.164.6.2.34.3	INTEGER	read-write	Enable/Disable authentication via RADIUS server.
INT agnSshAccess	1.3.6.1.4.1.164.6.2.34.4	INTEGER	read-write	Enable/Disable accessing the device via SSH. disable - no one will be allowed to access the device via SSH. enable - all users are allowed SSH Access. managersOnly - Only manager stations listed in the manager's list are allowed.
systemInterface	1.3.6.1.4.1.164.6.2.35
ifCreateTable	1.3.6.1.4.1.164.6.2.35.1		not-accessible	The Interface Configuration Table. This table enables to create interfaces of Entities.
ifCreateEntry	1.3.6.1.4.1.164.6.2.35.1.1		not-accessible	An entry in the Interface Configuration table.
SYS ifCreateEntityType	1.3.6.1.4.1.164.6.2.35.1.1.1	SysIfEntityType	read-only	This object indicates the Type of the Entity that exists above the created interface. For a Logical Port, this value can be: other (1) when there is no fixed entity above it.
I32 ifCreateEntityIdx	1.3.6.1.4.1.164.6.2.35.1.1.2	Integer32	read-only	This object indicates the Index of the Entity that exists above the created interface. For a Logical Port, this value can be: 9999 - N/A when there is no fixed entity above it.
I32 ifCreateNumber	1.3.6.1.4.1.164.6.2.35.1.1.3	Integer32	read-only	This object indicates the number of the Interface that is created.
ROW ifCreateRowStatus	1.3.6.1.4.1.164.6.2.35.1.1.4	RowStatus	read-create	This object enables the user to create/delete entries in this table.
IAN ifCreateType	1.3.6.1.4.1.164.6.2.35.1.1.5	IANAifType	read-create	This object indicates the Type of the Interface that is created.
I32 ifCreateIndex	1.3.6.1.4.1.164.6.2.35.1.1.6	Integer32	read-only	This object indicates the ifIndex of the created Interface. The ifIndex is assigned by the device.
I32 ifCreateConnectedTo	1.3.6.1.4.1.164.6.2.35.1.1.7	Integer32	read-create	This object indicates the entity connected to the created Interface. The value of this object can be ifIndex of the connected entity or any other number that can identify it.
U32 ifCreateParams	1.3.6.1.4.1.164.6.2.35.1.1.8	Unsigned32	read-create	This object represents one or more parameters of the created Interface. Each group of bits (one or more bits) represents a specific parameter and its possible values. This object's mapping and interpretation will be specified in each device's specification documents. The parameter should be used within the create PDU assuming atomic operation.
NUM ifCreateConnectionPointer	1.3.6.1.4.1.164.6.2.35.1.1.9	RowPointer	read-create	This parameter represents the entity that is connected to this Interface. It can be used instead of ifCreateConnectedTo. It is an OBJECT IDENTIFIER. This parameter's SYNTAX allows the following possibilities: - can be simply used for entity that is not an interface - is not limited to include up to 32 bits The value of this parameter is a pointer to an existing row of a table, where the entity connected to this Interface is defined (i.e. the pointer uniquely identifies the connected entity). Examples: In case of an interface (from 2863.ifTable): points to 'ifEntry' of corresponding row = . In case of a VPI/VCI (from 2515.atmVclTable): points to 'atmVclEntry' of corresponding row = ..VPI.VCI In case no entity is connected, value = 0 .
interfacePerformance	1.3.6.1.4.1.164.6.2.35.2
ifPerfTable	1.3.6.1.4.1.164.6.2.35.2.1		not-accessible	Interface Performance Table. The propose of this table is to support statistics counters having 64 bit by using 2 parameters with syntax= Integer32. This is because SNMPv1 does not support Counter64 properly. For SNMPv3, ifPerfHCCounter (Counter64) may be supported.
ifPerfEntry	1.3.6.1.4.1.164.6.2.35.2.1.1		not-accessible	An entry in the Interface Performance Table.
I32 ifPerfCounterType	1.3.6.1.4.1.164.6.2.35.2.1.1.1	Integer32	not-accessible	2nd index of the ifPerfTable. This parameter represents the Counter Type. Each application can have a different association between this object's value and counter type - see relevant application spec. For VPLS-MTU application use the following values: 1= Rx Octets, 2= Tx Octets, 3= Rx Frames, 4= Tx Frames, 5=Rx Dropped Frames, 6= Tx Dropped Frames. Optionally, counter type description appears in agnListDecodingTable
U32 ifPerfLowCounterPart	1.3.6.1.4.1.164.6.2.35.2.1.1.2	Unsigned32	read-only	In order to support Counters having 64 bit length, the performance counter is divided into two 32 bit parameters as follows: [ 64 bit parameter ] = [ High 32 bit parameter ][ Low 32 bit parameter ]. This parameter holds the Low 32 bits of the counter, while the following parameter holds the High 32 bits of the counter.
U32 ifPerfHighCounterPart	1.3.6.1.4.1.164.6.2.35.2.1.1.3	Unsigned32	read-only	This parameter holds the High 32 bits of the counter (see description in the above parameter).
C64 ifPerfHCCounter	1.3.6.1.4.1.164.6.2.35.2.1.1.4	Counter64	read-only	This High Capacity counter holds whole 64 bits of the counter indicated by ifPerfCounterType (concatenates both counter parts ifPerfHighCounterPart&ifPerfLowCounterPart) This object can be supported only by agents using SNMPv2 or SNMPv3.
systemOam	1.3.6.1.4.1.164.6.2.36
systemOamTable	1.3.6.1.4.1.164.6.2.36.1		not-accessible	The OAM Configuration Table.
systemOamEntry	1.3.6.1.4.1.164.6.2.36.1.1		not-accessible	An entry in the OAM table.
I32 systemOamCnfgIdx	1.3.6.1.4.1.164.6.2.36.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
I32 systemOamFrequency	1.3.6.1.4.1.164.6.2.36.1.1.2	Integer32	read-write	Time in sec. between 2 OAM packets.
I32 systemOamTimeoutCycles	1.3.6.1.4.1.164.6.2.36.1.1.3	Integer32	read-write	No. of cycles the agent will send OAM packets without receiving a response from the remote device before declaring that the connection to the remote side is down - Time Out.
INT systemOamLinkCheck	1.3.6.1.4.1.164.6.2.36.1.1.4	INTEGER	read-write	This MIB object determines whether continuous connectivity Link checks will be performed by the device for uplinks. For Vmux-2100: enable (3) value can be set upon device installation. In this case, TDM Link Connectivity checks can be performed even before the user configures the Links of the device.If the value is enable (3) and there is no connection with the remote side, the Test LED will blink on the Main Board Module.
systemOamDescrTable	1.3.6.1.4.1.164.6.2.36.2		not-accessible	The OAM Descriptors Configuration Table.
systemOamDescrEntry	1.3.6.1.4.1.164.6.2.36.2.1		not-accessible	An entry in the OAM table.
I32 systemOamDescrIdx	1.3.6.1.4.1.164.6.2.36.2.1.1	Integer32	not-accessible	The OAM Descriptor Index.
ROW systemOamDescrRowStatus	1.3.6.1.4.1.164.6.2.36.2.1.2	RowStatus	read-create	Enables the user to create/delete entries in this table.
INT systemOamDescrMode	1.3.6.1.4.1.164.6.2.36.2.1.3	INTEGER	read-create	The OAM Mode of the Descriptor.
INT systemOamDescrCCDirection	1.3.6.1.4.1.164.6.2.36.2.1.4	INTEGER	read-create	OAM Continuity Check function mode. both(2) - Agent sends OAM CC cells and checks received OAM CC cells. none(3) - Agent does not send and does not check received OAM CC cells. source(4)- Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells.
INT systemOamDescrLoopbackOperation	1.3.6.1.4.1.164.6.2.36.2.1.5	INTEGER	read-create	The OAM Loopback function mode. off(2) - Stop sending loopback OAM cells. on(3) - Start loopback OAM cells.
OCT systemOamDescrLoopbackDestAddr	1.3.6.1.4.1.164.6.2.36.2.1.6	OCTET STRING	read-create	Loopback Destination Address.
G32 systemOamDescrXcCounter	1.3.6.1.4.1.164.6.2.36.2.1.7	Gauge32	read-only	The number of connections that use this OAM Descriptor.
INT agnDeviceView	1.3.6.1.4.1.164.6.2.37	INTEGER	read-only	This variable denotes the view of the device: Look: old look, new look or new look 2. Material: Plastic or Metal.
bitMappingTable	1.3.6.1.4.1.164.6.2.38		not-accessible	This table maps bits of an octet string to an interface. For ACE-2002 this table is used to map bits of VLAN port lists to LAN VCC's. This table is the opposite view of the xcTable for xcBitMapping. It is used to ease the bit translation for the NMS.
bitMappingEntry	1.3.6.1.4.1.164.6.2.38.1		not-accessible	Each entry in the table describes a correlation of a bit location to an interface. For ACE-2002 - Upon creation of a new LAN VCC the agent will add an entry to this table that will define the bit location for that VCC.
I32 bitMappingLocation	1.3.6.1.4.1.164.6.2.38.1.1	Integer32	not-accessible	The bit location in an octet string.
I32 bitMappingIndex	1.3.6.1.4.1.164.6.2.38.1.2	Integer32	read-only	The interface index or any other index that should be mapped.
OCT bitMappingView	1.3.6.1.4.1.164.6.2.39	OCTET STRING	read-only	A view of the bitMappingTable in one object - each entry in the biMappingTable will have the corresponding Bit of this object (bitMappingLocation) = '1'. For ACE-2002 it is used to describe all the existing LAN VCC's So that the NMS can easily calculate which VCC's can be selected as members for a VLAN, instead of reading all the bitMapping Table.
hostTable	1.3.6.1.4.1.164.6.2.40		not-accessible	Host interface table.
hostEntry	1.3.6.1.4.1.164.6.2.40.1		not-accessible	An entry in the Host Table. The hostParam1, hostParam2, and hostParam3 entries may have different use in different applications.
I32 hostIndex	1.3.6.1.4.1.164.6.2.40.1.1	Integer32	not-accessible	The Host Table Index. This index can have the same value as Host No.
IP hostIP	1.3.6.1.4.1.164.6.2.40.1.2	IpAddress	read-create	The host interface IP address.
IP hostIPMask	1.3.6.1.4.1.164.6.2.40.1.3	IpAddress	read-create	The host interface subnet mask.
IP hostDefaultNextHop	1.3.6.1.4.1.164.6.2.40.1.4	IpAddress	read-create	The host interface Default Next Hop address.
I32 hostMode	1.3.6.1.4.1.164.6.2.40.1.5	Integer32	read-create	This parameter represents the Host mode of operation. There can be different values for each application. For example: Not Applicable = 1.
I32 hostParam1	1.3.6.1.4.1.164.6.2.40.1.6	Integer32	read-create	This parameter represents the first Host parameter. There can be different values for each application. For example: Not Applicable = 1.
I32 hostParam2	1.3.6.1.4.1.164.6.2.40.1.7	Integer32	read-create	This parameter represents the 2nd Host parameter. There can be different values for each application.
I32 hostParam3	1.3.6.1.4.1.164.6.2.40.1.8	Integer32	read-create	This parameter represents the 3nd Host parameter. There can be different values for each application.
ROW hostRowStatus	1.3.6.1.4.1.164.6.2.40.1.9	RowStatus	read-create	Creation/Deletion of rows in the table.
INT hostVlanTagging	1.3.6.1.4.1.164.6.2.40.1.10	INTEGER	read-create	Host VLAN support (Tagging). untag - No support of VLAN Tagging. tag - 4 VLAN bytes will be added to the frame.
I32 hostVlanId	1.3.6.1.4.1.164.6.2.40.1.11	Integer32	read-create	Host VLAN ID.
I32 hostVlanPriority	1.3.6.1.4.1.164.6.2.40.1.12	Integer32	read-create	Host VLAN Frame priority.
invNameXCTable	1.3.6.1.4.1.164.6.2.41		not-accessible	Inverse Name XC Table. This table can be used to ease the search for a connection first index by the connection name.
invNameXCEntry	1.3.6.1.4.1.164.6.2.41.1		not-accessible	An entry in the table.
STR invNameXC	1.3.6.1.4.1.164.6.2.41.1.1	SnmpAdminString	not-accessible	The unique Connection name, associated to a Cross-Connection.
OID invNameXCType	1.3.6.1.4.1.164.6.2.41.1.2	OBJECT IDENTIFIER	read-only	The OBJECT IDENTIFIER of the respective XC Table. Examples: XC Table invNameXCType --------------------------------------------------- atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .
I32 invNameXCIndex	1.3.6.1.4.1.164.6.2.41.1.3	Integer32	read-only	The XC Table (invNameXCType) may include more than one index. This object represents the value of the first XC Index.
OCT agnDeviceCapabilities	1.3.6.1.4.1.164.6.2.42	OCTET STRING	read-only	Indicates the optional capabilities that are implemented by this device and are manageable through this MIB. For each capability 1 BIT is allocated in each Octet starting from the LSB. If the value of the BIT = 1, the capability is Enabled. If the value of the BIT = 0, the capability is Disabled. For bit assignment, refer to device specification. Capabilities example: Router - BIT 0 (0000 0001 = 01 Hex = 1 Decimal). The 2nd octet (MSB) will represent the maximum number of intervals that the Agent can keep in its DB (same for all ports). For Vmux, this object describes agent's support of LBRAD coder feature: 1 octet ; bit 0 (LSB). '1' - LBRAD feature is supported '0' - LBRAD feature is not supported.
rowInfoTable	1.3.6.1.4.1.164.6.2.43		not-accessible	This table holds information of other tables.
rowInfoEntry	1.3.6.1.4.1.164.6.2.43.1		not-accessible	An entry in the table.
OID rowInfoTableId	1.3.6.1.4.1.164.6.2.43.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of the Table, which its information is held by this table (rowInfoTable). Examples: Table Name rowInfoTableId --------------------------------------------------- atmTrafficDescrParamTable 1.3.6.1.2.1.37.1.5 atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .
I32 rowInfoCounter	1.3.6.1.4.1.164.6.2.43.1.2	Integer32	read-only	The Number of rows in the table, indicated by rowInfoTableId.
I32 rowInfoIndexNext	1.3.6.1.4.1.164.6.2.43.1.3	Integer32	read-only	The First Free Index of the table, indicated by rowInfoTableId.
I32 rowInfoMaxNoOfRows	1.3.6.1.4.1.164.6.2.43.1.4	Integer32	read-only	The maximum possible number of rows in the table, indicated by rowInfoTableId.
INT agnStoreCmd	1.3.6.1.4.1.164.6.2.44	INTEGER	read-write	Store command. inFlash(3) = store the current Agent configuration in Flash memory. asDefConfigFile(4) = store the current Agent configuration as Default Configuration file (e.g. 'DefConfig.cfg'). Agent will perform the required command and change automatically the value of this object to off(2).
agnFunctionTable	1.3.6.1.4.1.164.6.2.45		not-accessible	This table is used in order to activate/deactivate device functions. The index indicates the function. Each function can be Enabled or Disabled.
agnFunctionEntry	1.3.6.1.4.1.164.6.2.45.1		not-accessible	An entry in the table.
INT agnFunction	1.3.6.1.4.1.164.6.2.45.1.1	INTEGER	not-accessible	This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock.
INT agnFunctionActivation	1.3.6.1.4.1.164.6.2.45.1.2	INTEGER	read-write	This MIB object indicates the activation of the current function.
I32 agnManagerConfigPorts	1.3.6.1.4.1.164.6.2.46	Integer32	read-write	This variable defines from which port/s this manager can manage the device. The value is a sum of 2**n, where n is a bit assigned to a certain port. For RIC-E1 and ETX 102 the value will be according to the ports combination: Network = bit 0 User= bit 1 For Example: All = 3.
INT agnEgressRateRange	1.3.6.1.4.1.164.6.2.47	INTEGER	read-write	This variable defines the valid ranges of egress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.
I32 agnNoOfCurrentConns	1.3.6.1.4.1.164.6.2.48	Integer32	read-only	This variable indicates the number of connections currently configured for the agent.
INT agnIngressRateRange	1.3.6.1.4.1.164.6.2.49	INTEGER	read-write	This variable defines the valid ranges of ingress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.
alarmForwardingTable	1.3.6.1.4.1.164.6.2.50		not-accessible	The Alarm Forwarding Mechanism will be operated for this table entries.
alarmForwardingEntry	1.3.6.1.4.1.164.6.2.50.1		not-accessible	Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.
I32 alarmForwardingFailPort	1.3.6.1.4.1.164.6.2.50.1.1	Integer32	not-accessible	An Index of the port on which a fail occurs.
I32 alarmForwardingToPort	1.3.6.1.4.1.164.6.2.50.1.2	Integer32	not-accessible	An Index of the port that will be affected upon the failure of the alarmForwardingFailPort.
ROW alarmForwardingRowStatus	1.3.6.1.4.1.164.6.2.50.1.3	RowStatus	read-create	Creation/ Deletion of rows in the table.
I32 alarmForwardingRecoveryTime	1.3.6.1.4.1.164.6.2.50.1.4	Integer32	read-create	This parameter defines the maximum time (sec) the affected port will hold the down state.
I32 alarmForwardingGroupConditions	1.3.6.1.4.1.164.6.2.50.1.5	Integer32	read-create	This parameter is applicable when there is a group of interfaces in which a fault may occur, and one interface to which alarm is propagated (forwarded). 0 = All - Forwarding will take place only when all interfaces of the same group are faulty. 1 = Single - Forwarding will take place when at least one (single) interface of the same group (any of them) is faulty. n - forwarding will take place only when n (n < all) interfaces of the same group fail.
BIT alarmForwardingCause	1.3.6.1.4.1.164.6.2.50.1.6	Bits	read-create	Bit map representing the cause upon which alarm forwarding will take place. bit 0 - LOSS (LINE DOWN) bit 1 - AIS bit 2 - RDI bit 3 - PROTOCOL DOWN.
INT alarmForwardingRecoveryMode	1.3.6.1.4.1.164.6.2.50.1.7	INTEGER	read-create	This parameter determines the Recovery Mode. manual - The user should stop the alarm forwarding by using the alarmForwardingRecoveryCommand. automatic - Alarm forwarding will be automatically stopped upon alarmForwardingFailPort recovery.
INT alarmForwardingRecoveryCommand	1.3.6.1.4.1.164.6.2.50.1.8	INTEGER	read-create	This parameter is a command. It is applicable when alarmForwardingRecoveryMode = manual. on - Will stop alarm forwarding. After setting to 'On', the agent will set this parameter back to 'Off'.
U32 alarmForwardingDelay	1.3.6.1.4.1.164.6.2.50.1.9	Unsigned32	read-create	This parameter determines the period of time (in seconds) the alarm of the alarmForwardingFailPort should exist before starting alarm forwarding.
INT alarmForwardingDirection	1.3.6.1.4.1.164.6.2.50.1.10	INTEGER	read-create	This parameter determines the Direction of the Alarm Forwarding. unidirectional - alarmForwardingFailPort affects the alarmForwardingToPort. bidirectional - alarmForwardingFailPort affects the alarmForwardingToPort AND vice-versa. For such cases, this value will be selected, instead of entering an additional unidirectional entry in the table, where the indexes are swapped.
BIT alarmForwardingAction	1.3.6.1.4.1.164.6.2.50.1.11	Bits	read-create	Bit map representing the action to be performed when alarm forwarding will take place. bit 0 - No Action. '1' value - device should NOT perform any action, though other bits indicate the action to be taken. '0' value - device should perform the action/s indicated by rest of the bits. In this case, one of the other bits should be '1'. bit 1 - Interface Deactivation (of the affected Port: alarmForwardingToPort) bit 2 - OAM Signaling. Affected Port (alarmForwardingToPort) will send special OAM Signaling to the Far-End unit about the Failure. This object will be used only for devices that support Deactivation per entry OR can support more than one action.
INT agnSwVersionSwapCmd	1.3.6.1.4.1.164.6.2.51	INTEGER	read-write	SW switch command. mainAndBackup (3) = Swap between Main SW and the backup one. Agent will perform the required command and change automatically the value of this object to off(2).
agnClockSource	1.3.6.1.4.1.164.6.2.52
agnClkSrcPortTable	1.3.6.1.4.1.164.6.2.52.1		not-accessible	Pool of Ports for the Master/Fallback Clock Source and of Recovered IDs. For devices with more than one configuration: Set operation is valid only to the TmpCnfg entry.
agnClkSrcPortEntry	1.3.6.1.4.1.164.6.2.52.1.1		not-accessible	An entry in the table.
I32 agnClkSrcPortCnfgIdx	1.3.6.1.4.1.164.6.2.52.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. For product supporting a single configuration, the value will be 1.
INT agnClkSrcPortSrcIdx	1.3.6.1.4.1.164.6.2.52.1.1.2	INTEGER	not-accessible	Clock Source Index. master - refers to Master clock fallback - refers to Fallback clock recovered - refers to Recovered clock.
I32 agnClkSrcPortIdx	1.3.6.1.4.1.164.6.2.52.1.1.3	Integer32	not-accessible	This object indicates the running Idx of the port that is to be used as Clock Source, for each agnClkSrcPortSrcIdx instance. In case of Recovered Clock - it indicates the Clock ID.
I32 agnClkSrcPort	1.3.6.1.4.1.164.6.2.52.1.1.4	Integer32	read-create	This object indicates the Port/Interface Index of the port that is to be used as Clock Source. In case of Recovered Clock - it indicates the PW number.
ROW agnClkSrcPortRowStatus	1.3.6.1.4.1.164.6.2.52.1.1.5	RowStatus	read-create	This object enables Creation/ Deletion of rows in the table.
INT agnClkSrcPortAdminStatus	1.3.6.1.4.1.164.6.2.52.1.1.6	INTEGER	read-create	This object indicates the Recovered Clock Administrative Status.
INT agnClkSrcPortType	1.3.6.1.4.1.164.6.2.52.1.1.7	INTEGER	read-create	This object is relevant only in case of Recovery Clock. It indicates the Clock Type.
INT agnClkSrcPortQuality	1.3.6.1.4.1.164.6.2.52.1.1.8	INTEGER	read-create	This object indicates the Clock Source Quality.
INT agnClkSrcPortNetType	1.3.6.1.4.1.164.6.2.52.1.1.9	INTEGER	read-create	This object is relevant only in case of Recovery Clock. It indicates the Clock Network Type, i.e. the PSN network characteristics and behavior.
INT agnClkSrcPortState	1.3.6.1.4.1.164.6.2.52.1.1.10	INTEGER	read-only	This object indicates the Clock State. freeRun(1) - Clock recovery is not locked to any clock. frequencyAcquisition(2) - Adaptive clock recovery is learning the frequency. rapidPhaseLock(3) - Clock recovery is in training process till it reaches fine phase lock. finePhaseLock(4) - Clock is locked and clock recovery is qualified and stable. holdover(5) - Clock recovery is in holdover mode. notApplicable(6) - Clock recovery is not applicable. .
agnCurrClkTable	1.3.6.1.4.1.164.6.2.52.2		not-accessible	Current Clock Source.
agnCurrClkEntry	1.3.6.1.4.1.164.6.2.52.2.1		not-accessible	An entry in the table.
I32 agnCurrClkObjIdx	1.3.6.1.4.1.164.6.2.52.2.1.1	Integer32	not-accessible	This MIB object identifies the object for which the Clock Source is used (System, Other System, Card).
INT agnCurrClkMode	1.3.6.1.4.1.164.6.2.52.2.1.2	INTEGER	read-only	Current Clock Source Mode. master - refers Master clock fallback - refers Fallback clock internal - only when both Master and Fallback Sources failed
INT agnCurrClkSrc	1.3.6.1.4.1.164.6.2.52.2.1.3	INTEGER	read-only	This object indicates the Current Clock Source.
I32 agnCurrClkPort	1.3.6.1.4.1.164.6.2.52.2.1.4	Integer32	read-only	This object indicates the Port/Interface Index of the port that is Currently used as Clock Source.
INT agnCurrClkHoldover	1.3.6.1.4.1.164.6.2.52.2.1.5	INTEGER	read-only	Current Clock Holdover State. As a last resort, in the absence of higher quality timing: - a SONET/SDH object can enter 'holdover' state, until higher quality external timing becomes available again. In this state (value=yes) the SONET/SDH object uses its own timing circuits for clock of the SONET/SDH signal. - for other objects, the 'holdover'=yes state means that the object uses last available clock (stored by the object) for a pre-defined time, until another clock source is used.
INT agnCurrClkSsmBased	1.3.6.1.4.1.164.6.2.52.2.1.6	INTEGER	read-only	This parameter indicates whether clock source is selected based on receive clock quality. Clock quality is indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging).
INT agnCurrClkState	1.3.6.1.4.1.164.6.2.52.2.1.7	INTEGER	read-only	This object indicates the Current Clock State. freeRun(1) - Current clock state machine is not locked and run from the internal oscillator. rapidPhaseLock(2) - Current clock state machine is locked. finePhaseLock(3) - Current clock state machine is in pre-locking. holdover(4) - Current clock state machine is in holdover mode (due to loss of event). .
INT agnCurrClkQualification	1.3.6.1.4.1.164.6.2.52.2.1.8	INTEGER	read-only	This object indicates the Current Clock Qualification and defines whether the PLL can locked according to the stratum definitions.
agnClockMonitoring	1.3.6.1.4.1.164.6.2.52.3
agnClkCurrentTable	1.3.6.1.4.1.164.6.2.52.3.1		not-accessible	The Clock Current table.
agnClkCurrentEntry	1.3.6.1.4.1.164.6.2.52.3.1.1		not-accessible	An entry in the Clock Current table.
U32 agnClkCurrentIndex	1.3.6.1.4.1.164.6.2.52.3.1.1.1	Unsigned32	not-accessible	An Index that is uniquely represents the Clock.
G32 agnClkCurrentRxPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.2	Gauge32	read-only	The counter associated with the number of Received Packets, encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkCurrentLostPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.3	Gauge32	read-only	The counter associated with the number of Lost Packets, encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkCurrentOutOfOrderPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.4	Gauge32	read-only	The counter associated with the number of times Out-of-Order Packets encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkCurrentBufferUnderflow	1.3.6.1.4.1.164.6.2.52.3.1.1.5	Gauge32	read-only	The counter associated with the number of times Underflow event encountered by a Bridge Port in the current 15 minute interval.
agnClkIntervalTable	1.3.6.1.4.1.164.6.2.52.3.2		not-accessible	The Clock Interval table.
agnClkIntervalEntry	1.3.6.1.4.1.164.6.2.52.3.2.1		not-accessible	An entry in the Clock Interval table.
U32 agnClkIntervalIndex	1.3.6.1.4.1.164.6.2.52.3.2.1.1	Unsigned32	not-accessible	An Index that is uniquely represents the Clock.
U32 agnClkIntervalNumber	1.3.6.1.4.1.164.6.2.52.3.2.1.2	Unsigned32	not-accessible	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
G32 agnClkIntervalRxPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.3	Gauge32	read-only	The counter associated with the number of Received Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 agnClkIntervalLostPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.4	Gauge32	read-only	The counter associated with the number of Lost Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 agnClkIntervalOutOfOrderPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.5	Gauge32	read-only	The counter associated with the number of times Out-of-Order Packets are detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 agnClkIntervalBufferUnderflow	1.3.6.1.4.1.164.6.2.52.3.2.1.6	Gauge32	read-only	The counter associated with the number of times Underflow event is detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
I32 agnMaxNoOfConns	1.3.6.1.4.1.164.6.2.53	Integer32	read-only	This variable indicates the maximum number of connections that can be configured for the agent.
lag	1.3.6.1.4.1.164.6.2.54
lagTable	1.3.6.1.4.1.164.6.2.54.1		not-accessible	A table defining Link Aggregation Groups port association, and other parameters.
lagEntry	1.3.6.1.4.1.164.6.2.54.1.1		not-accessible	An entry in the LAG table.
U32 lagCnfgIdx	1.3.6.1.4.1.164.6.2.54.1.1.1	Unsigned32	not-accessible	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 lagIdx	1.3.6.1.4.1.164.6.2.54.1.1.2	Unsigned32	not-accessible	This object indicates LAG unique index.
POR lagPortMembers	1.3.6.1.4.1.164.6.2.54.1.1.3	PortList	read-create	The set of ports which are permanently assigned to the Link Aggregation Group. The default value of this object is a string of zeros.
INT lagDistributionMethod	1.3.6.1.4.1.164.6.2.54.1.1.4	INTEGER	read-create	This object defines the criteria for the 802.3ad (LAG) to split the traffic between ports
INT lagRecoveryMode	1.3.6.1.4.1.164.6.2.54.1.1.5	INTEGER	read-create	This object defines whether traffic will be returned to a port after its recovery. This object is applicable only when lagDistributionMethod= oneToOne (3).
U32 lagWaitToRestore	1.3.6.1.4.1.164.6.2.54.1.1.6	Unsigned32	read-create	This object defines traffic recovery time (in seconds) to the port after its recovery. This object is applicable only when lagRecoveryMode= revertive (3).
ROW lagRowStatus	1.3.6.1.4.1.164.6.2.54.1.1.7	RowStatus	read-create	This object enables user to create/delete entries of this table. Note: When using LAG standard package, this table is static, hence, only the values active(1), notInService(2) are used.
U32 lagShutDownDurationUponFlip	1.3.6.1.4.1.164.6.2.54.1.1.8	Unsigned32	read-create	This object defines the duration (in seconds) the active port transmission is shut down after LAG Flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0=no shut-down. This object is applicable only when lagDistributionMethod=oneToOne(3) and mainly when each of the Links of our device is connected to a different device.
INT lagRdnMethod	1.3.6.1.4.1.164.6.2.54.1.1.9	INTEGER	read-create	This object defines the redundancy method.
INT lagLacpEnable	1.3.6.1.4.1.164.6.2.54.1.1.10	INTEGER	read-create	Enabling/Disabling the LACP for a LAG. The LACP will be enabled for all ports belonging to this LAG.
lagStatTable	1.3.6.1.4.1.164.6.2.54.2		not-accessible	A table defining Link Aggregation Groups Redundancy. This table is applicable only when lagDistributionMethod = oneToOne.
lagStatEntry	1.3.6.1.4.1.164.6.2.54.2.1		not-accessible	An entry in the LAG Status table.
U32 lagStatForcePort	1.3.6.1.4.1.164.6.2.54.2.1.1	Unsigned32	read-write	This object enables user to enforce the active port. 0 = No Enforcement; Otherwise the ifIndex of the port.
U32 lagStatActivePort	1.3.6.1.4.1.164.6.2.54.2.1.2	Unsigned32	read-only	This object indicates the current active port. It is applicable only when lagDistributionMethod = oneToOne. The value is the ifIndex of the port. 0 = none of the ports is active.
gfp	1.3.6.1.4.1.164.6.2.55
gfpCnfgTable	1.3.6.1.4.1.164.6.2.55.1		not-accessible	Configuration table for GFP (General Framing Protocol).
gfpCnfgEntry	1.3.6.1.4.1.164.6.2.55.1.1		not-accessible	An entry in the GFP configuration table.
U32 gfpCnfgIdx	1.3.6.1.4.1.164.6.2.55.1.1.1	Unsigned32	not-accessible	Index to GFP configuration table.
INT gfpPayloadFcs	1.3.6.1.4.1.164.6.2.55.1.1.2	INTEGER	read-write	This object defines whether protocol header will include FCS.
INT gfpRxTxScramble	1.3.6.1.4.1.164.6.2.55.1.1.3	INTEGER	read-write	This object defines whether transmission will be scrambled.
INT gfpVcatHeader	1.3.6.1.4.1.164.6.2.55.1.1.4	INTEGER	read-write	VCAT header is LCAS CONTROL packet as described in the G-7043. one control packet is transmitted in a period of 16 Multi frame
agnGroupTable	1.3.6.1.4.1.164.6.2.56		not-accessible	A table that enables associating components to Group/s (or removing components of a group). The Group Idx can then be used in other tables (e.g alarmForwardingTable).
agnGroupEntry	1.3.6.1.4.1.164.6.2.56.1		not-accessible	An entry in the agnGroupTable.
U32 agnGroupCnfgIdx	1.3.6.1.4.1.164.6.2.56.1.1	Unsigned32	not-accessible	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 agnGroupIdx	1.3.6.1.4.1.164.6.2.56.1.2	Unsigned32	not-accessible	This object indicates a unique Group Index.
U32 agnGroupComponentIdx	1.3.6.1.4.1.164.6.2.56.1.3	Unsigned32	not-accessible	This object indicates a unique Component Index that belongs to the Group defined by agnGroupIdx.
ROW agnGroupRowStatus	1.3.6.1.4.1.164.6.2.56.1.4	RowStatus	read-create	This object enables user to create/delete entries of this table. destroy - If a Group is used in another table, Agent may not allow destroying the entry/ies that belong to this Group Index.
I32 agnStatNoOfUploadedIntervals	1.3.6.1.4.1.164.6.2.57	Integer32	read-only	This parameter indicates the Number of Intervals that were successfully collected and uploaded in the last statistics collection session.
agnSyslog	1.3.6.1.4.1.164.6.2.58
U32 agnSyslogDeviceUdpPort	1.3.6.1.4.1.164.6.2.58.1	Unsigned32	read-write	The UDP Port of the device, from which Syslog messages are sent. Default=514.
INT agnSyslogFacility	1.3.6.1.4.1.164.6.2.58.2	INTEGER	read-write	A user defined SW module, task or function, from which Syslog messages are sent to the remote Server.
INT agnSyslogSeverityLevel	1.3.6.1.4.1.164.6.2.58.3	INTEGER	read-write	Device will send events equal or exceeding this severity level (configured by user).
INT agnNetworkInterfaceType	1.3.6.1.4.1.164.6.2.59	INTEGER	read-write	This MIB object indicates the network interface type to be used by the device. It is used for devices that use only one network port type.
U32 agnTrapDelay	1.3.6.1.4.1.164.6.2.60	Unsigned32	read-write	This variable enables the user to set a delay (in seconds) before a trap is sent. This delay will be used only for traps that need to be sent during device initialization. It is needed because the device connected to our device starts transmitting traps later. The delay starts from the end of the Boot process. The device will keep the init traps in the correct order, and cancel those which clear former ones in the list. After this init delay, traps will be sent without a delay.
agnStringToIndexTable	1.3.6.1.4.1.164.6.2.62		not-accessible	This table holds the conversions of tables from unique String to numeric index.
agnStringToIndexEntry	1.3.6.1.4.1.164.6.2.62.1		not-accessible	An entry in the table.
OID agnStringToIndexTableId	1.3.6.1.4.1.164.6.2.62.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of the Table, having as index numeric values. In this table, the value of agnStringToIndexUserName is an attribute.
STR agnStringToIndexUserName	1.3.6.1.4.1.164.6.2.62.1.2	SnmpAdminString	not-accessible	This object indicates a unique name used by agnStringToIndexTableId, although it is not it's index.
U32 agnStringToIndexTableIndex	1.3.6.1.4.1.164.6.2.62.1.3	Unsigned32	read-only	The numeric Index of agnStringToIndexTableId.
agnRowPointerTable	1.3.6.1.4.1.164.6.2.63		not-accessible	This table holds information about a specific entry in a table. For example, number of usages of this row.
agnRowPointerEntry	1.3.6.1.4.1.164.6.2.63.1		not-accessible	An entry in the table.
OID agnRowPointerIndex	1.3.6.1.4.1.164.6.2.63.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of an entry in a table.
U32 agnRowPointerNoOfUsages	1.3.6.1.4.1.164.6.2.63.1.2	Unsigned32	read-only	The number of usages of specific entry in a table, which is pointed by agnRowPointerIndex.Usually, when the value of this counter is greater than 0,the entry cannot be removed.
services	1.3.6.1.4.1.164.6.3
wfq	1.3.6.1.4.1.164.6.3.1
wfqTable	1.3.6.1.4.1.164.6.3.1.1		not-accessible	This table allows user to define several WFQ tables per output port. WFQ supports flows with different bandwidth requirements by giving each queue a weight that assigns it a different percentage of output port bandwidth. When Weighted Fair Queuing is used, it is possible to precisely attribute bandwidth partitioning among the queues. When there is congestion, each class (queue) is not allowed to use more bandwidth than the amount allocated to it.
wfqEntry	1.3.6.1.4.1.164.6.3.1.1.1		not-accessible	An entry in the Weighted Fair Queueing table.
I32 wfqCnfgIdx	1.3.6.1.4.1.164.6.3.1.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
I32 wfqPrtIdx	1.3.6.1.4.1.164.6.3.1.1.1.2	Integer32	not-accessible	This object indicates a unique port or interface number, for which Weighted Fair Queueing table is applicable . For numbering, see product's spec. For some products, the numbering can equal ifIndex. Value of 255 (not applicable) refer to system level queue
I32 wfqTblIdx	1.3.6.1.4.1.164.6.3.1.1.1.3	Integer32	not-accessible	This object indicates which Weighted Fair Queueing (WFQ) Table is being used. There can be several tables. For FCD-155 User will select which one will be used for a virtual concatenation group.Valid values are 1,2
I32 wfqQueueIdx	1.3.6.1.4.1.164.6.3.1.1.1.4	Integer32	not-accessible	This object indicates a queue index. For FCD-155, valid queues are 1..3. The 4th queue is not in MIB. Its weight will be RO, Calculated according to the sum of the 3 first queues.
ROW wfqRowStatus	1.3.6.1.4.1.164.6.3.1.1.1.5	RowStatus	read-create	This object enables Creation/Deletion of rows in the WFQ table. For FCD-155, rows are not created nor destroyed by user.
I32 wfqWeightValue	1.3.6.1.4.1.164.6.3.1.1.1.6	Integer32	read-create	This object indicates a relative weight value. User should make sure that the sum of values for all queues will not exceed 100% (sum should be BELOW 100% in order to leave some BW percentage for last queue) Note that when this attribute is being used, the wfqMinRateAbsolute attribute is NA.
INT wfqSchedulingMode	1.3.6.1.4.1.164.6.3.1.1.1.7	INTEGER	read-create	This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme or priority Queue (Strict Priority).
U32 wfqMinRateAbsolute	1.3.6.1.4.1.164.6.3.1.1.1.8	Unsigned32	read-create	The minimum absolute rate, in kbps, that should be allocated to this queue. If the value is zero, then there is effectively no minimum rate guarantee. If the value is non-zero, then the servicing of this queue in at least this rate is assured. Note that when this attribute is being used, the wfqWeightValue attribute is NA.
U32 wfqMaxPacketSize	1.3.6.1.4.1.164.6.3.1.1.1.9	Unsigned32	read-create	The size of the largest packet which can be received on this queue, specified in octets. Packets larger than this size will be discarded.
dscpMapping	1.3.6.1.4.1.164.6.3.2
dscpMappingTable	1.3.6.1.4.1.164.6.3.2.1		not-accessible	Mapping of DSCP value to a regenerated priority level.
dscpMappingEntry	1.3.6.1.4.1.164.6.3.2.1.1		not-accessible	An entry in dscpMappingTable.
I32 dscpMappingCnfgIdx	1.3.6.1.4.1.164.6.3.2.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer to. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.
DSC dscpMappingDscpIdx	1.3.6.1.4.1.164.6.3.2.1.1.2	Dscp	not-accessible	DSCP value of the incoming IP packet
I32 dscpMappingRegenPriority	1.3.6.1.4.1.164.6.3.2.1.1.3	Integer32	read-write	The Regenerated Priority level the incoming DSCP value is mapped to. For FCD-155, valid values are 0,1,2,3
ifTeQos	1.3.6.1.4.1.164.6.3.3
ifTeQosTable	1.3.6.1.4.1.164.6.3.3.1		not-accessible	The TE QOS Interface Table.
ifTeQosEntry	1.3.6.1.4.1.164.6.3.3.1.1		not-accessible	An entry in the TE QOS Interface table.
I32 ifTeQosIdx1	1.3.6.1.4.1.164.6.3.3.1.1.1	Integer32	not-accessible	This object indicates the 1st Index of the table.
I32 ifTeQosIdx2	1.3.6.1.4.1.164.6.3.3.1.1.2	Integer32	not-accessible	This object indicates the 2nd Index of the table.
I32 ifTeQosIdx3	1.3.6.1.4.1.164.6.3.3.1.1.3	Integer32	not-accessible	This object indicates the 3rd Index of the table.
OCT ifTeQosParam	1.3.6.1.4.1.164.6.3.3.1.1.4	OCTET STRING	read-write	This object is used for QOS attributes of the entry's entities.
OCT ifTeQosParam2	1.3.6.1.4.1.164.6.3.3.1.1.5	OCTET STRING	read-write	This object is used for 2nd group QOS attributes of the entry's entities.
INT ifTeQosStatus	1.3.6.1.4.1.164.6.3.3.1.1.6	INTEGER	read-write	This object is used to create, activate and destroy entries of this table.
portQos	1.3.6.1.4.1.164.6.3.4
prtPriorityTable	1.3.6.1.4.1.164.6.3.4.1		not-accessible	A table - Parameters per port per Priority .
prtPriorityEntry	1.3.6.1.4.1.164.6.3.4.1.1		not-accessible	An entry in table.
I32 prtPriorityIdx1	1.3.6.1.4.1.164.6.3.4.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. or any other Index.
I32 prtPriorityPrtIdx	1.3.6.1.4.1.164.6.3.4.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
I32 prtPriorityIdx	1.3.6.1.4.1.164.6.3.4.1.1.3	Integer32	not-accessible	This object indicates the Traffic Priority Index.
I32 prtPriorityIngressRateLimit	1.3.6.1.4.1.164.6.3.4.1.1.4	Integer32	read-write	The maximum rate permitted at Ingress of this port with this Traffic Priority, in Kbps.
prtQosTable	1.3.6.1.4.1.164.6.3.4.2		not-accessible	Port QoS (Quality of Service) table.
prtQosEntry	1.3.6.1.4.1.164.6.3.4.2.1		not-accessible	An entry in table.
U32 prtQosIdx	1.3.6.1.4.1.164.6.3.4.2.1.1	Unsigned32	not-accessible	The first index of the table. This attribute might indicate the Idx of the Cnfg (1..255) being accessed ; Idx of 255 relates to the TmpCnfg or any other Index.
U32 prtQosPrtIdx	1.3.6.1.4.1.164.6.3.4.2.1.2	Unsigned32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
INT prtQosDirection	1.3.6.1.4.1.164.6.3.4.2.1.3	INTEGER	not-accessible	This object indicates the port's QoS Direction.
INT prtQosRateLimitPacketType	1.3.6.1.4.1.164.6.3.4.2.1.4	INTEGER	read-write	This object indicates the Type of Packets on which Rate Limitation is applied.
U32 prtQosRateLimitCIR	1.3.6.1.4.1.164.6.3.4.2.1.5	Unsigned32	read-write	This object indicates the port's CIR (Committed Information Rate) in Kbps. Value=0 represents best effort.
U32 prtQosRateLimitCBS	1.3.6.1.4.1.164.6.3.4.2.1.6	Unsigned32	read-write	This object indicates the port's CBS (Committed Burst Size) in KB. Value=0 represents best effort.
U32 prtQosRateLimitEIR	1.3.6.1.4.1.164.6.3.4.2.1.7	Unsigned32	read-write	This object indicates the port's EIR (Excess Information Rate) in Kbps.
U32 prtQosRateLimitEBS	1.3.6.1.4.1.164.6.3.4.2.1.8	Unsigned32	read-write	This object indicates the port's EBS (Excess Burst Size) in KB.
prtTrafficClass	1.3.6.1.4.1.164.6.3.5
portTrafficClassTable	1.3.6.1.4.1.164.6.3.5.1		not-accessible	Mapping of port to Traffic Class level.
portTrafficClassEntry	1.3.6.1.4.1.164.6.3.5.1.1		not-accessible	An entry in portTrafficClassTable.
I32 portTrafficClassIdx1	1.3.6.1.4.1.164.6.3.5.1.1.1	Integer32	not-accessible	This attribute indicates the 1st index of the table. This may be the Idx of the Cnfg(1..255) being accessed; Idx of 255 relates to the TmpCnfg, or any other Index.
I32 portTrafficClassPortIdx	1.3.6.1.4.1.164.6.3.5.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
I32 portTrafficClass	1.3.6.1.4.1.164.6.3.5.1.1.3	Integer32	read-write	This object indicates the Traffic Class level of this port.
serviceTable	1.3.6.1.4.1.164.6.3.6		not-accessible	Table of services.
serviceEntry	1.3.6.1.4.1.164.6.3.6.1		not-accessible	An entry in the Service Table.
U32 flowIndex	1.3.6.1.4.1.164.6.3.6.1.1	Unsigned32	not-accessible	Defines the Flow ID the service is associated to.
U32 serviceIndex	1.3.6.1.4.1.164.6.3.6.1.2	Unsigned32	not-accessible	Defines the Service ID - according to the CoS.
ROW serviceRowStatus	1.3.6.1.4.1.164.6.3.6.1.3	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
STR serviceName	1.3.6.1.4.1.164.6.3.6.1.4	SnmpAdminString	read-create	This attribute defines the service name.
U32 serviceBwProfileId	1.3.6.1.4.1.164.6.3.6.1.5	Unsigned32	read-create	This variable holds the index of the Ingress BW profile assigned to that service.
evcCosTable	1.3.6.1.4.1.164.6.3.7		not-accessible	This table defines mapping of Ethernet Virtual Connection (EVC) ID to Class of Service (CoS) ID
evcCosEntry	1.3.6.1.4.1.164.6.3.7.1		not-accessible	An entry in table.
U32 evcCosCnfgIdx	1.3.6.1.4.1.164.6.3.7.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 evcCosEvcIdx	1.3.6.1.4.1.164.6.3.7.1.2	Unsigned32	not-accessible	This attribute indicates EVC Id.
ROW evcCosRowStatus	1.3.6.1.4.1.164.6.3.7.1.3	RowStatus	read-create	This attribute allows to create/delete a row in this table.
STR evcCosEvcName	1.3.6.1.4.1.164.6.3.7.1.5	SnmpAdminString	read-create	A string that identifies the EVC. It should be unique in the Maintenance Domain (i.e., in the managed network) Used as MEG ID field in OAM messages.
U32 evcCosSpVlanId	1.3.6.1.4.1.164.6.3.7.1.6	Unsigned32	read-create	This object indicates the SP (Service Provider) VLAN used when sending an OAM message for the specified EVC.
serviceStatTable	1.3.6.1.4.1.164.6.3.8		not-accessible	Service statistics table.
serviceStatEntry	1.3.6.1.4.1.164.6.3.8.1		not-accessible	An entry in the Service Statistics Table.
INT serviceStatDirection	1.3.6.1.4.1.164.6.3.8.1.1	INTEGER	not-accessible	The direction in wich the measurement is taken.
G32 srvForwardGreenPackets	1.3.6.1.4.1.164.6.3.8.1.2	Gauge32	read-only	This attribute displays the counted number of forwarded packets that where marked Green.
G32 srvForwardGreenPacktesOverflow	1.3.6.1.4.1.164.6.3.8.1.3	Gauge32	read-only	This attribute displays the number of times that the forwardGreenPackets counter has overflowed.
G32 srvForwardYellowPackets	1.3.6.1.4.1.164.6.3.8.1.4	Gauge32	read-only	This attribute displays the counted number of forwarded packets that where marked Yellow.
G32 srvForwardYellowPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.5	Gauge32	read-only	This attribute displays the number of times that the forwardYellowPackets counter has overflowed.
G32 srvDiscardGreenPacket	1.3.6.1.4.1.164.6.3.8.1.6	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Green.
G32 srvDiscardGreenPacketOverflow	1.3.6.1.4.1.164.6.3.8.1.7	Gauge32	read-only	This attribute displays the number of times that the discardGreenPacket counter has overflowed.
G32 srvDiscardYellowRedPackets	1.3.6.1.4.1.164.6.3.8.1.8	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Yellow or Red.
G32 srvDiscardYellowRedPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.9	Gauge32	read-only	This attribute displays the number of times that the discardYellowRedPackets counter has overflowed.
G32 srvForwardGreenBytes	1.3.6.1.4.1.164.6.3.8.1.10	Gauge32	read-only	This attribute displays the counted number of forwarded bytes that where marked Green.
G32 srvForwardGreenBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.11	Gauge32	read-only	This attribute displays the number of times that the forwardGreenBytes counter has overflowed.
G32 srvForwardYellowBytes	1.3.6.1.4.1.164.6.3.8.1.12	Gauge32	read-only	This attribute displays the counted number of forwarded bytes that where marked Yellow.
G32 srvForwardYellowBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.13	Gauge32	read-only	This attribute displays the number of times that the forwardYellowBytes counter has overflowed.
G32 srvDiscardGreenBytes	1.3.6.1.4.1.164.6.3.8.1.14	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Green.
G32 srvDiscardGreenBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.15	Gauge32	read-only	This attribute displays the number of times that the discardGreenBytes counter has overflowed.
G32 srvDiscardYellowRedBytes	1.3.6.1.4.1.164.6.3.8.1.16	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Yellow or Red.
G32 srvDiscardYellowRedBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.17	Gauge32	read-only	This attribute displays the number of times that the discardYellowRedBytes counter has overflowed.
INT srvResetStatsCmd	1.3.6.1.4.1.164.6.3.8.1.18	INTEGER	read-create	Reset statistic counters of the service.
G32 srvDiscardYellowPackets	1.3.6.1.4.1.164.6.3.8.1.19	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Yellow.
G32 srvDiscardYellowPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.20	Gauge32	read-only	This attribute displays the number of times that the discardYellowPackets counter has overflowed.
G32 srvDiscardYellowBytes	1.3.6.1.4.1.164.6.3.8.1.21	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Yellow.
G32 srvDiscardYellowBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.22	Gauge32	read-only	This attribute displays the number of times that the discardYellowBytes counter has overflowed.
G32 srvDiscardRedPackets	1.3.6.1.4.1.164.6.3.8.1.23	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Red.
G32 srvDiscardRedPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.24	Gauge32	read-only	This attribute displays the number of times that the discardRedPackets counter has overflowed.
G32 srvDiscardRedBytes	1.3.6.1.4.1.164.6.3.8.1.25	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Red.
G32 srvDiscardRedBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.26	Gauge32	read-only	This attribute displays the number of times that the discardRedBytes counter has overflowed.
mappingProfileObjects	1.3.6.1.4.1.164.6.3.9
flowMappingProfileTable	1.3.6.1.4.1.164.6.3.9.1		not-accessible	This table holds flow mapping profiles.
flowMappingProfileEntry	1.3.6.1.4.1.164.6.3.9.1.1		not-accessible	Each entry in this table describes one Flow mapping profile with one of its Flow Mapping supported, according to the Priority order. The information includes a reference to a Flow Mapping index.
U32 flowMappingProfileIndex	1.3.6.1.4.1.164.6.3.9.1.1.1	Unsigned32	not-accessible	A running index for the Flow Mapping Profile table.
INT flowMappingProfilePriority	1.3.6.1.4.1.164.6.3.9.1.1.2	INTEGER	not-accessible	The priority of the Mapping selected by flowMappingProfileMapIndex within the Flow Mapping Profile.
ROW flowMappingProfileRowStatus	1.3.6.1.4.1.164.6.3.9.1.1.3	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
U32 flowMappingProfileNumOfMaps	1.3.6.1.4.1.164.6.3.9.1.1.4	Unsigned32	read-create	This attribute determines the number of the mappings associated to the Flow Mapping Profile.
U32 flowMappingProfileMapIndex	1.3.6.1.4.1.164.6.3.9.1.1.5	Unsigned32	read-create	This attribute holds a reference to the mapping index. It specifies the mapping selected for the Mapping Profile for the selected Priority. When flowMappingProfileNumOfMaps=0, this attribute is not relevant.
STR flowMappingProfileName	1.3.6.1.4.1.164.6.3.9.1.1.6	SnmpAdminString	read-create	This attribute defines the name assigned to flowMappingIndex profile.
qosFlowMappingTable	1.3.6.1.4.1.164.6.3.9.2		not-accessible	A table of Flow Mapping.
qosFlowMappingEntry	1.3.6.1.4.1.164.6.3.9.2.1		not-accessible	Each entry in this table describes one Flow Mapping. The information includes combination (AND function) of all the classifications, as defined in the qosFlowMappingCriteria field. Classifiers are: TOS, DSCP, VLAN ID, MAC and IP source and destination addresses, IP protocol, IP Precedence, TCP and UDP source and destination ports.
U32 qosFlowMappingIdx1	1.3.6.1.4.1.164.6.3.9.2.1.1	Unsigned32	not-accessible	- In case the table is accessed via flowMappingProfileTable this is a running index for the QoS Flow Mapping table. - In case the table is not accessed via flowMappingProfileTable, this will be the ifIndex of the XNI (bridge port) to which the QoS mapping applies.
U32 qosFlowMappingIdx2	1.3.6.1.4.1.164.6.3.9.2.1.2	Unsigned32	not-accessible	An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the index of the Flow (EVC) to which the QoS mapping applies.
U32 qosFlowMappingIdx3	1.3.6.1.4.1.164.6.3.9.2.1.3	Unsigned32	not-accessible	An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the Priority to which the QoS mapping applies.
ROW qosFlowMappingRowStatus	1.3.6.1.4.1.164.6.3.9.2.1.4	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
BIT qosFlowMappingCriteria	1.3.6.1.4.1.164.6.3.9.2.1.5	Bits	read-create	This attribute determines upon which criterion the flow will be mapped.
U32 qosFlowMappingIeee802dot1p	1.3.6.1.4.1.164.6.3.9.2.1.6	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different 802.1 P-bit value. Setting '1' to the bit means that the corresponding 802.1 P-bit value is applicable. It is relevant only in case the ieee802dot1p bit(0) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingTos	1.3.6.1.4.1.164.6.3.9.2.1.7	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different TOS value. Setting '1' to the bit means that the corresponding TOS value is applicable. It is relevant only in case the tos bit (1) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromDscp	1.3.6.1.4.1.164.6.3.9.2.1.8	Unsigned32	read-create	This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToDscp	1.3.6.1.4.1.164.6.3.9.2.1.9	Unsigned32	read-create	This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromVlanId	1.3.6.1.4.1.164.6.3.9.2.1.10	Unsigned32	read-create	This attribute determines the first VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToVlanId	1.3.6.1.4.1.164.6.3.9.2.1.11	Unsigned32	read-create	This attribute determines the last VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingFromSrcMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.12	MacAddress	read-create	This attribute determines the first source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingToSrcMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.13	MacAddress	read-create	This attribute determines the last source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingFromDestMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.14	MacAddress	read-create	This attribute determines the first destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingToDestMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.15	MacAddress	read-create	This attribute determines the last destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.
IP qosFlowMappingFromSrcIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.16	IpAddress	read-create	This attribute determines the first source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.
IP qosFlowMappingToSrcIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.17	IpAddress	read-create	This attribute determines the last source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.
IP qosFlowMappingFromDestIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.18	IpAddress	read-create	This attribute determines the first destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.
IP qosFlowMappingToDestIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.19	IpAddress	read-create	This attribute determines the last destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromTcpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.20	Unsigned32	read-create	This attribute determines the first TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToTcpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.21	Unsigned32	read-create	This attribute determines the last TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromTcpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.22	Unsigned32	read-create	This attribute determines the first TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToTcpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.23	Unsigned32	read-create	This attribute determines the last TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromUdpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.24	Unsigned32	read-create	This attribute determines the first UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToUdpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.25	Unsigned32	read-create	This attribute determines the last UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromUdpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.26	Unsigned32	read-create	This attribute determines the first UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToUdpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.27	Unsigned32	read-create	This attribute determines the last UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromIpPrecedence	1.3.6.1.4.1.164.6.3.9.2.1.28	Unsigned32	read-create	This attribute determines the first IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToIpPrecedence	1.3.6.1.4.1.164.6.3.9.2.1.29	Unsigned32	read-create	This attribute determines the last IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingInnerIeee802dot1p	1.3.6.1.4.1.164.6.3.9.2.1.30	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different inner 802.1 P-bit value. Setting '1' to the bit means that the corresponding inner 802.1 P-bit value is applicable. It is relevant only in case the innerIeee802dot1p bit (13) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromInnerVlanId	1.3.6.1.4.1.164.6.3.9.2.1.31	Unsigned32	read-create	This attribute determines the first inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToInnerVlanId	1.3.6.1.4.1.164.6.3.9.2.1.32	Unsigned32	read-create	This attribute determines the last inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.
cosProfileTable	1.3.6.1.4.1.164.6.3.10		not-accessible	Class of Service Profile table. Each profile holds a priority method, and a mappring function that maps the priority values (range according to the method) into CoS values.
cosProfileEntry	1.3.6.1.4.1.164.6.3.10.1		not-accessible	A conceptual row where each row contains one CoS attributes.
U32 cosProfileIndex	1.3.6.1.4.1.164.6.3.10.1.1	Unsigned32	not-accessible	Defines the CoS Profile ID.
ROW cosProfileRowStatus	1.3.6.1.4.1.164.6.3.10.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
INT cosProfileCosMethod	1.3.6.1.4.1.164.6.3.10.1.3	INTEGER	read-create	Defines the priority method upon CoS mapping is done.
STR cosProfileName	1.3.6.1.4.1.164.6.3.10.1.4	SnmpAdminString	read-create	This attribute defines the name assigned to CoS profile.
OCT cosProfileCosMapping	1.3.6.1.4.1.164.6.3.10.1.5	OCTET STRING	read-create	This attribute defines the value of the CoS that is assigned for each priority. The number of the valid octets depends upon the priority method selected: Octet 0 corresponds to priority = 0 Octet 1 corresponds to priority = 1 ... Octet 63 corresponds to priority = 63.
queueProfileObjects	1.3.6.1.4.1.164.6.3.11
qProfileTable	1.3.6.1.4.1.164.6.3.11.1		not-accessible	This table defines the profiles for a cluster of queues.
qProfileEntry	1.3.6.1.4.1.164.6.3.11.1.1		not-accessible	A conceptual row where each row contains one Queue Cluster attribute.
U32 qProfileIndex	1.3.6.1.4.1.164.6.3.11.1.1.1	Unsigned32	not-accessible	Defines the Queue Cluster Profile ID.
ROW qProfileRowStatus	1.3.6.1.4.1.164.6.3.11.1.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
STR qProfileName	1.3.6.1.4.1.164.6.3.11.1.1.3	SnmpAdminString	read-create	This attribute holds the name of the Queue cluster profile.
U32 qProfileNumberOfInternalQ	1.3.6.1.4.1.164.6.3.11.1.1.4	Unsigned32	read-create	This attribute holds the number of the internal queue profiles that are pointed by qInternalQProfile.
OCT qProfileInternalQProfile	1.3.6.1.4.1.164.6.3.11.1.1.5	OCTET STRING	read-create	This attribute holds the indexes to the queue profiles in the qInternalProfileTable. Each couple of octets holds an index to the qInternalProfileTable.
qInternalProfileTable	1.3.6.1.4.1.164.6.3.11.2		not-accessible	This table holds queue profiles.
qInternalProfileEntry	1.3.6.1.4.1.164.6.3.11.2.1		not-accessible	A conceptual row where each row contains one Queue attribute.
U32 qInternalProfileIndex	1.3.6.1.4.1.164.6.3.11.2.1.1	Unsigned32	not-accessible	Defines the Queue Profile ID.
ROW qInternalProfileRowStatus	1.3.6.1.4.1.164.6.3.11.2.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
INT qInternalProfileScheduling	1.3.6.1.4.1.164.6.3.11.2.1.3	INTEGER	read-create	This attribute determines the queue scheduling method.
U32 qInternalProfileWFQWeight	1.3.6.1.4.1.164.6.3.11.2.1.4	Unsigned32	read-create	This attribute determines the weight that each WFQ (Weighted Fair Queue) participant gets. It is applicable only when scheduling is configured to WFQ.
U32 qInternalProfileQueueLength	1.3.6.1.4.1.164.6.3.11.2.1.5	Unsigned32	read-create	This attribute determines the length of the queue.
U32 qInternalProfileWredStartDropThresh	1.3.6.1.4.1.164.6.3.11.2.1.6	Unsigned32	read-create	This attribute determines the length that the queue (Start Value) must reach before the packets colored yellow will start being dropped by the WRED (Weighted Random Early Detection/Discard) mechanism. WRED is one the most commonly used method for congestion avoidance.
U32 qInternalProfileWredDropAllThresh	1.3.6.1.4.1.164.6.3.11.2.1.7	Unsigned32	read-create	This attribute determines the length that the queue (Stop Value) must reach before the WRED (Weighted Random Early Detection) shaper mechanism stops dropping randomly, and just drops all further packets marked as yellow.
U32 qInternalProfileWredDropProbability	1.3.6.1.4.1.164.6.3.11.2.1.8	Unsigned32	read-create	This attribute determines the percentage of packets that are being dropped at the point when the length of the queue reaches the Stop value. So, effectively, this defines how quickly the rate of dropping packet must increase as the queue length grows from the Start Value to the Stop Value.
U32 qInternalProfileRateLimit	1.3.6.1.4.1.164.6.3.11.2.1.9	Unsigned32	read-create	This attribute determines the Rate Limit of the queue in Kbps. Value=0 represents best effort.
U32 qInternalProfileShaperProfile	1.3.6.1.4.1.164.6.3.11.2.1.10	Unsigned32	read-create	This attribute defines the Shaper Profile (bwProfileIndex from bwProfileTable) assigned to this qInternalProfile. Valid range of bwProfileIndex for Shaper Profiles is 0x8000001-0x8000041. If set to '0', no profile is assigned to this qInternalProfile.
queueGroupTable	1.3.6.1.4.1.164.6.3.11.3		not-accessible	This table defines the queue groups/blocks,their level and connections between them.
queueGroupEntry	1.3.6.1.4.1.164.6.3.11.3.1		not-accessible	A conceptual row where each row contains one Queue group.
STR queueGroupName	1.3.6.1.4.1.164.6.3.11.3.1.1	SnmpAdminString	not-accessible	Defines the Queue Group unique name.
U32 queueGroupQBlockLevel	1.3.6.1.4.1.164.6.3.11.3.1.2	Unsigned32	not-accessible	This attribute holds the Level of the Queue Block .First level is 1. NA=2^32-1.
U32 queueGroupQBlockIdx	1.3.6.1.4.1.164.6.3.11.3.1.3	Unsigned32	not-accessible	This attribute holds the ID of the Queue Block. NA=2^32-1.
ROW queueGroupRowStatus	1.3.6.1.4.1.164.6.3.11.3.1.4	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
U32 queueGroupQBlockProfile	1.3.6.1.4.1.164.6.3.11.3.1.5	Unsigned32	read-create	This attribute defines the Queue profile assigned to this Queue Block. This object points to qProfileIndex in qProfileTable.
U32 queueGroupQBlockShaperProfile	1.3.6.1.4.1.164.6.3.11.3.1.6	Unsigned32	read-create	This attribute defines the Shaper profile assigned to this Queue Block.
STR queueGroupPointToQBlock	1.3.6.1.4.1.164.6.3.11.3.1.7	SnmpAdminString	read-create	This attribute defines the Queue Block name of the next Queue Block level that is pointed by this Queue Block.
U32 queueGroupPointToInternalQueue	1.3.6.1.4.1.164.6.3.11.3.1.8	Unsigned32	read-create	This attribute defines the internal queue whithin queueGroupPointToQBlock that is pointed by this Queue Block.
STR queueGroupQBlockName	1.3.6.1.4.1.164.6.3.11.3.1.9	SnmpAdminString	read-create	This attribute holds the name of the Queue Block.
markingProfileTable	1.3.6.1.4.1.164.6.3.12		not-accessible	Marking profile table. Each profile holds a marking function which converts CoS values to Service Provider priority values.
markingProfileEntry	1.3.6.1.4.1.164.6.3.12.1		not-accessible	A conceptual row where each row contains one Marking attribute.
U32 markingProfileIndex	1.3.6.1.4.1.164.6.3.12.1.1	Unsigned32	not-accessible	Defines the Marking Profile ID.
ROW markingProfileRowStatus	1.3.6.1.4.1.164.6.3.12.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
STR markingProfileName	1.3.6.1.4.1.164.6.3.12.1.3	SnmpAdminString	read-create	This attribute defines the unique name assigned to the Marking profile.
OCT markingSpVlanPBit	1.3.6.1.4.1.164.6.3.12.1.4	OCTET STRING	read-create	For ETX-202A : This attribute defines the value of the SP VLAN P-Bit that is assigned for each CoS: Octet 0 corresponds to CoS = 0 Octet 1 corresponds to CoS = 1 ... Octet 7 corresponds to CoS = 7. For LA-210 from V1.5 : This attribute defines the value of the SP VLAN P-Bit that is assigned for each frame according to the value of markingProfileMethod parameter : Octet 0 corresponds to value 0 of 802.1 P-bit/DSCP/TOS. Octet 1 corresponds to value 1 of 802.1 P-bit/DSCP/TOS. ... Octet 7 corresponds to value 7 of 802.1 P-bit/DSCP/TOS. Octets 8-63 correspond to DSCP values 8-63.
INT markingProfileMethod	1.3.6.1.4.1.164.6.3.12.1.5	INTEGER	read-create	This attribute defines the method upon which marking is done.
radTransport	1.3.6.1.4.1.164.6.4
radTransportDomains	1.3.6.1.4.1.164.6.4.1
radTransportDomainSnmpEfmOam	1.3.6.1.4.1.164.6.4.1.1			The SNMP over EFM OAM transport domain. The corresponding transport address is of type RadTransportAddressEfmOam for EFM OAM addresses (port).
radStkHub	1.3.6.1.4.1.164.7
radRouter	1.3.6.1.4.1.164.11
rtrBridge	1.3.6.1.4.1.164.11.7
webranger	1.3.6.1.4.1.164.11.7.2
wrSysConfig	1.3.6.1.4.1.164.11.7.2.1
INT wrBraodcastCtrlCmd	1.3.6.1.4.1.164.11.7.2.1.1	INTEGER	read-write	This parameter is a command to the webranger CPU. It enables blocking or forwarding broadcast frames, which may cause a trigger to a connection. block (1) - blocks the broadcast frames. forward (2) - forwards the broadcast frames. blockLinkPropagation (3) - blocks the broadcast frames to the links, tx to the LAN.
INT wrFrSelfLearningMode	1.3.6.1.4.1.164.11.7.2.1.2	INTEGER	read-write	This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol. off - will get the configuration by setting it. on - disables configuration and start self learning.
INT wrGratuitousArp	1.3.6.1.4.1.164.11.7.2.1.3	INTEGER	read-write	This parameter enables/disables the Gratuitous ARP feature. When enabled, the feature means: when receiving ARP with sender's Source IP Address that already exists in the ARP table - replace MAC Address with sender's Source MAC Address.
wrIpRouterInfo	1.3.6.1.4.1.164.11.7.2.2
wrConfigIpDhcp	1.3.6.1.4.1.164.11.7.2.2.1
INT wrDhcpAction	1.3.6.1.4.1.164.11.7.2.2.1.1	INTEGER	read-write	Activating (disable/enable) DHCP server operation. Since DHCP Server and DHCP Relay cannot reside in same device, DHCP Relay may be enabled (per interface), only if server action is disabled. For some devices, this object is used in order to enable/disable the DHCP Client. See device SDS.
wrDhcpTable	1.3.6.1.4.1.164.11.7.2.2.1.2		not-accessible	A list of DHCP entries. The number of entries is up to DHCP current entries, according to the WEBRANger model.
wrDhcpEntry	1.3.6.1.4.1.164.11.7.2.2.1.2.1		not-accessible	DHCP parameters per entry of the DHCP table.
IP wrDhcpLowIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.1	IpAddress	read-create	DHCP Low Ip Address.
IP wrDhcpHighIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.2	IpAddress	read-create	DHCP High Ip Address.
IP wrDhcpIpMaskAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.3	IpAddress	read-create	IP mask Address.
IP wrDhcpDefaultGateway	1.3.6.1.4.1.164.11.7.2.2.1.2.1.4	IpAddress	read-create	Default Gateway's IP Address.
IP wrDhcpPrimaryDNS	1.3.6.1.4.1.164.11.7.2.2.1.2.1.5	IpAddress	read-create	Primary DNS.
IP wrDhcpSecondaryDNS	1.3.6.1.4.1.164.11.7.2.2.1.2.1.6	IpAddress	read-create	Secondary DNS.
INT wrDhcpInterface	1.3.6.1.4.1.164.11.7.2.2.1.2.1.7	INTEGER	read-create	The IP addresse allocation is done according to the interface type from which the DHCP request arrives.
ROW wrDhcpRowStatus	1.3.6.1.4.1.164.11.7.2.2.1.2.1.8	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrDhcpRowStatus.id = active(1). For destroying a row, the NMS should set: wrDhcpStatus.id = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
I32 wrDhcpIpAddressLeaseTime	1.3.6.1.4.1.164.11.7.2.2.1.2.1.9	Integer32	read-create	Allocated IP Address lease time in seconds. A zero value specifies no time limitation.
STR wrDhcpPoolName	1.3.6.1.4.1.164.11.7.2.2.1.2.1.10	SnmpAdminString	read-create	DHCP pool name - string with max length of 10 characters
IP wrDhcpTftpServerIp	1.3.6.1.4.1.164.11.7.2.2.1.2.1.11	IpAddress	read-create	DHCP pool - TFTP-server IP Address.
STR wrDhcpConfigFileName	1.3.6.1.4.1.164.11.7.2.2.1.2.1.12	SnmpAdminString	read-create	TFTP-name of the configuration File Name for DHCP pool.
dhcpPoolAllocTable	1.3.6.1.4.1.164.11.7.2.2.1.3		not-accessible	A list of DHCP Pool Allocation entries. Each entry (row) consist of a single IP Address belonging to DHCP pool whose lowest IP address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing, or may already be leased (in use) by Host it's MacAddress is dhcpPoolAllocMacAddress. Time left for leasing period is indicated by dhcpPoolAllocTimeLeft. All posible statuses of IP address are indicated and controlled by dhcpPoolAllocFlags
dhcpPoolAllocEntry	1.3.6.1.4.1.164.11.7.2.2.1.3.1		not-accessible	DHCP Pool Allocation parameters per entry of the DHCP Pool Allocation table.
IP dhcpPoolAllocLowIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.1	IpAddress	read-only	Lowest IP address of this pool, value eqaul to wrDhcpLowIpAddress for the pool.
IP dhcpPoolAllocLeasingIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.2	IpAddress	read-only	Single IP Address belonging to dhcp pool whose Lowest Ip Address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing or may be leased by Host its MacAddress is dhcpPoolAllocMacAddress. All posible statuses of IP address are indicated by dhcpPoolAllocFlags
MAC dhcpPoolAllocMacAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.3	MacAddress	read-only	MAC Address to which the IP address has been leased
I32 dhcpPoolAllocTimeLeft	1.3.6.1.4.1.164.11.7.2.2.1.3.1.4	Integer32	read-only	IP address leasing time left in seconds
INT dhcpPoolAllocFlags	1.3.6.1.4.1.164.11.7.2.2.1.3.1.5	INTEGER	read-only	These flags indicates status of each IP address. User may change value to free, via dhcpPoolAllocFreeCmd
INT dhcpPoolAllocFreeCmd	1.3.6.1.4.1.164.11.7.2.2.1.3.1.6	INTEGER	read-write	Setting this attribute to On (3), will enforce the agent to Free this entry. The Agent will change the value of this MIB object to off(2) automatically, after performing the command. Setting this object to off(2), will do nothing
dhcpRelayTable	1.3.6.1.4.1.164.11.7.2.2.1.4		not-accessible	A list of DHCP relay entries.
dhcpRelayEntry	1.3.6.1.4.1.164.11.7.2.2.1.4.1		not-accessible	DHCP Relay parameters per entry of the DHCP relay table.
INT dhcpRelayAction	1.3.6.1.4.1.164.11.7.2.2.1.4.1.1	INTEGER	read-write	Setting this attribute to enable (3), will enable DHCP Relay action for this interface (Only if DHCP Server is disabled for device - wrDhcpAction=disable). dhcpRelayServerIpAddressaddress should not be 0.0.0.0 when enable is set
IP dhcpRelayServerIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.4.1.2	IpAddress	read-write	DHCP Server IP Address.
I32 dhcpRelayMaxHop	1.3.6.1.4.1.164.11.7.2.2.1.4.1.3	Integer32	read-write	Maximum number of hops till DHCP Server. upper limit is 16 hops
INT wrDhcpPort	1.3.6.1.4.1.164.11.7.2.2.1.5	INTEGER	read-write	This parameter defines the port that DHCP flow will be actiavted.
dhcpClientTable	1.3.6.1.4.1.164.11.7.2.2.1.6		not-accessible	A list of DHCP client entries.
dhcpClientEntry	1.3.6.1.4.1.164.11.7.2.2.1.6.1		not-accessible	DHCP Client parameters per entry of the DHCP Client table.
INT dhcpClientAction	1.3.6.1.4.1.164.11.7.2.2.1.6.1.1	INTEGER	read-write	This parameter default value is enable(3). Setting this attribute to disable (2), will disable DHCP Client action for this interface. This parameter can be changed to disable (2) only (it cannot be changed from disable to enable).
IP dhcpClientServerIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.6.1.2	IpAddress	read-write	DHCP Server IP Address.
I32 dhcpClientLeaseExpirationTime	1.3.6.1.4.1.164.11.7.2.2.1.6.1.3	Integer32	read-only	This parameter holds the time (in minutes) left until lease expiration.
STR dhcpClientStatus	1.3.6.1.4.1.164.11.7.2.2.1.6.1.4	DisplayString	read-only	This parametr displays the DHCP status.
dhcpIfClientTable	1.3.6.1.4.1.164.11.7.2.2.1.7		not-accessible	DHCP client entries for each Interface.
dhcpIfClientEntry	1.3.6.1.4.1.164.11.7.2.2.1.7.1		not-accessible	DHCP Clients per entry of the DHCP Interface Client table.
IP dhcpIfClientIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.7.1.2	IpAddress	read-create	DHCP Client IP Address.
ROW dhcpIfClientRowStatus	1.3.6.1.4.1.164.11.7.2.2.1.7.1.3	RowStatus	read-create	The row status used for creating, modifying, and deleting instances of the columnar objects in the dhcpIfClientTable. For Vmux Devices, it will be possible only to Delete instances. The addition of Clients will be done automatically by the Server according to Network messages that are sent by the Clients; not via SNMP. In order to Delete a Client, this MIB object should be set to: destroy (6).
INT dhcpServerAction	1.3.6.1.4.1.164.11.7.2.2.1.8	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the Server. deleteAllClients (3) is an option that is used for a device functioning as a server. It will remove all the clients from all the interfaces of the device. When the operation is complete, the agent will return a noOp (2) value.
wrConfigIpDNS	1.3.6.1.4.1.164.11.7.2.2.2
INT wrDNSRelayAction	1.3.6.1.4.1.164.11.7.2.2.2.1	INTEGER	read-write	When Enabled, device will act as a DNS Relay: whenever the device receives a DNS request from its host, it will forward it to the DNS server as if the request was initiated by the device itself. The reply from the DNS server is forwarded by the device to the host as if the device was answering the request.
wrConfigIpxRouterInfo	1.3.6.1.4.1.164.11.7.2.3
INT wrAutoLearnLanIpxNets	1.3.6.1.4.1.164.11.7.2.3.1	INTEGER	read-write	Activating (disable/enable) the auto-learn operation.
wrLanIpxNetTable	1.3.6.1.4.1.164.11.7.2.3.2		not-accessible	Lan IPX nets Table.
wrLanIpxNetEntry	1.3.6.1.4.1.164.11.7.2.3.2.1		not-accessible	IPX Nets per frame type & LAN port. The table entries will be created by the agent
I32 wrLanIfIndex	1.3.6.1.4.1.164.11.7.2.3.2.1.1	Integer32	read-only	LAN port ifIndex.
INT wrLanIpxFrameType	1.3.6.1.4.1.164.11.7.2.3.2.1.2	INTEGER	read-only	Frame Type
IP wrIpxNetAddress	1.3.6.1.4.1.164.11.7.2.3.2.1.3	IpAddress	read-write	Net address per Frame Type & LAN port.
IP wrDialInIpxNet	1.3.6.1.4.1.164.11.7.2.3.3	IpAddress	read-write	Net address through a link.
ripSapIfConfTable	1.3.6.1.4.1.164.11.7.2.3.4		not-accessible	A list of Interfaces which require separate configuration in RIP/SAP.
ripSapIfConfEntry	1.3.6.1.4.1.164.11.7.2.3.4.1		not-accessible	A Single Routing Domain in a single Subnet.
I32 ripSapIfConfIfIndex	1.3.6.1.4.1.164.11.7.2.3.4.1.1	Integer32	read-only	The interface ifIndex.
INT ripSapIfConfMode	1.3.6.1.4.1.164.11.7.2.3.4.1.2	INTEGER	read-create	The ifIndex RIP/SAP mode.
ROW ripSapIfConfStatus	1.3.6.1.4.1.164.11.7.2.3.4.1.3	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set ripSapIfConfStatus.id1 = active(1). For destroying a row, the NMS should set: ripSapIfConfStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
wrInterface	1.3.6.1.4.1.164.11.7.2.4
wrIpAddressTable	1.3.6.1.4.1.164.11.7.2.4.1		not-accessible	Link IP addresses Table.
wrIpAddressEntry	1.3.6.1.4.1.164.11.7.2.4.1.1		not-accessible	Ip Address per Link
I32 wrIpIfIndex	1.3.6.1.4.1.164.11.7.2.4.1.1.1	Integer32	read-only	Port interface index.
IP wrIpAddress	1.3.6.1.4.1.164.11.7.2.4.1.1.2	IpAddress	read-create	Link IP Address.
IP wrIpMask	1.3.6.1.4.1.164.11.7.2.4.1.1.3	IpAddress	read-create	Link IP mask Address.
ROW wrIpRowStatus	1.3.6.1.4.1.164.11.7.2.4.1.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrIpRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrIpRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
wrSpoofingTable	1.3.6.1.4.1.164.11.7.2.4.2		not-accessible	Spoofing Table.
wrSpoofingEntry	1.3.6.1.4.1.164.11.7.2.4.2.1		not-accessible	Spoofing per Link
I32 wrSpoofingIfIndex	1.3.6.1.4.1.164.11.7.2.4.2.1.1	Integer32	read-only	Port interface index.
I32 wrSpoofingAction	1.3.6.1.4.1.164.11.7.2.4.2.1.2	Integer32	read-create	Spoofing action is applied by bit code: enable : bit 0 set (disable: bit 0 is 0) keepAlive : bit 1 ... : bit 2 and so on. For the above example, to set spoofing to keepAlive action, the object's value will be 3 = [ 20 + 21 ] Only the Remote WEBRANger will accept this object ! -------
I32 wrSpoofingAgingStation	1.3.6.1.4.1.164.11.7.2.4.2.1.3	Integer32	read-create	Aging time of stations list, in min. The agent 'translates' the time entered in minutes, to 10 min. resolution, as follows: 1..10 min - 10 min 11..20 min - 20 min and so on... 0 is not a valid value. Only the Remote WEBRANger will accept this object ! ----------------
ROW wrSpoofingRowStatus	1.3.6.1.4.1.164.11.7.2.4.2.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrSpoofingRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrSpoofingRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
wrLanIfTable	1.3.6.1.4.1.164.11.7.2.4.3		not-accessible	Link IP addresses Table.
wrLanIfEntry	1.3.6.1.4.1.164.11.7.2.4.3.1		not-accessible	Ip Address per Link
INT wrLanBridgeRouterMode	1.3.6.1.4.1.164.11.7.2.4.3.1.2	INTEGER	read-write	This parameter indicates whether the link is Bridge or Router and specifies the Router's type.
INT wrLanIfState	1.3.6.1.4.1.164.11.7.2.4.3.1.3	INTEGER	read-write	The LAN is disabled or enabled. For LAN 2 it can be also 'redundancy'.
I32 wrLanIfRdnTimeout	1.3.6.1.4.1.164.11.7.2.4.3.1.4	Integer32	read-write	LAN Redundancy Timeout in seconds. Applicable when wrLanIfState=redundancy.
wrSyncCnfgTable	1.3.6.1.4.1.164.11.7.2.4.4		not-accessible	Configuration table for Async interface.
wrSyncCnfgEntry	1.3.6.1.4.1.164.11.7.2.4.4.1		not-accessible	Configuration table
I32 wrSyncIfIndex	1.3.6.1.4.1.164.11.7.2.4.4.1.1	Integer32	read-only	Sync interface index.
INT wrSyncClkMode	1.3.6.1.4.1.164.11.7.2.4.4.1.2	INTEGER	read-write	Clock Mode.
INT wrSyncClkRate	1.3.6.1.4.1.164.11.7.2.4.4.1.3	INTEGER	read-write	Clock Rate in. Rate can be changed if Clock Mode is Program only.
wrFrCnfgTable	1.3.6.1.4.1.164.11.7.2.4.5		not-accessible	Configuration table for Fr parameters that do not exist in RFC2115.
wrFrCnfgEntry	1.3.6.1.4.1.164.11.7.2.4.5.1		not-accessible	Configuration entry for Fr parameters that do not exist in RFC2115.
INT wrFrDlciLearningMode	1.3.6.1.4.1.164.11.7.2.4.5.1.1	INTEGER	read-write	This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol for the current interface. off - the WR will read the user's configuration for this interface. on - the WR will begin self learning of the current interface's maintanance protocol and DLCIs.
INT wrFrCllmMessages	1.3.6.1.4.1.164.11.7.2.4.5.1.2	INTEGER	read-write	This parameter enables/disables the Webranger to Tx/Rx CLLM (Consolidated Link Layer Management) messages via DLCI 1023. The CLLM messages are link layer control messages. They can be used for example in cases of congestion. The CLLM message contains a code for cause of congestion and list of all DLCIs that should act to reduce data transmission.
radAtm	1.3.6.1.4.1.164.12
atmGen	1.3.6.1.4.1.164.12.2
atmPerfHistory	1.3.6.1.4.1.164.12.2.1
atmIfPerformance	1.3.6.1.4.1.164.12.2.1.1
atmIfDataTable	1.3.6.1.4.1.164.12.2.1.1.1		not-accessible	The ATM interface Data table.
atmIfDataEntry	1.3.6.1.4.1.164.12.2.1.1.1.1		not-accessible	An entry in the ATM interface Data table.
I32 atmIfTimeElapsed	1.3.6.1.4.1.164.12.2.1.1.1.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
I32 atmIfValidIntervals	1.3.6.1.4.1.164.12.2.1.1.1.1.2	Integer32	read-only	The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
C32 atmIfTxCells	1.3.6.1.4.1.164.12.2.1.1.1.1.3	Counter32	read-only	The counter associated with the total number of transmitted cells, encountered by an ATM interface.
C32 atmIfRxCells	1.3.6.1.4.1.164.12.2.1.1.1.1.4	Counter32	read-only	The counter associated with the total number of received cells, encountered by an ATM interface.
C32 atmIfUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.1.1.5	Counter32	read-only	The counter associated with the total number of cells with uncorrected HEC errors, encountered by an ATM interface.
atmIfCurrentTable	1.3.6.1.4.1.164.12.2.1.1.2		not-accessible	The ATM interface Current table.
atmIfCurrentEntry	1.3.6.1.4.1.164.12.2.1.1.2.1		not-accessible	An entry in the ATM interface Current table.
G32 atmIfCurrentTxCells	1.3.6.1.4.1.164.12.2.1.1.2.1.1	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentRxCells	1.3.6.1.4.1.164.12.2.1.1.2.1.2	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentCorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.2.1.3	Gauge32	read-only	The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.2.1.4	Gauge32	read-only	The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentHecErrorSeconds	1.3.6.1.4.1.164.12.2.1.1.2.1.5	Gauge32	read-only	The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in the current 15 minute interval.
atmIfIntervalTable	1.3.6.1.4.1.164.12.2.1.1.3		not-accessible	The ATM interface Interval table.
atmIfIntervalEntry	1.3.6.1.4.1.164.12.2.1.1.3.1		not-accessible	An entry in the ATM interface Interval table.
I32 atmIfIntervalNumber	1.3.6.1.4.1.164.12.2.1.1.3.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmIfIntervalTxCells	1.3.6.1.4.1.164.12.2.1.1.3.1.2	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalRxCells	1.3.6.1.4.1.164.12.2.1.1.3.1.3	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalCorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.3.1.4	Gauge32	read-only	The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.3.1.5	Gauge32	read-only	The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalHecErrorSeconds	1.3.6.1.4.1.164.12.2.1.1.3.1.6	Gauge32	read-only	The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
atmPvcPerformance	1.3.6.1.4.1.164.12.2.1.2
atmVpPerformance	1.3.6.1.4.1.164.12.2.1.2.1
atmVpCurrentTable	1.3.6.1.4.1.164.12.2.1.2.1.1		not-accessible	The ATM VP Current table.
atmVpCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.1.1.1		not-accessible	An entry in the ATM VP Current table.
I32 atmVpCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.1.1.1.1	Integer32	read-only	The VPI of the VPL.
G32 atmVpCurrentRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.1.1.1.2	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.1.1.1.3	Gauge32	read-only	The counter associated with the number of received cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.1.1.1.4	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.1.1.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentRxAIS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.6	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentTxAIS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.7	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.
G32 atmVpCurrentRxRDI	1.3.6.1.4.1.164.12.2.1.2.1.1.1.8	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentTxRDI	1.3.6.1.4.1.164.12.2.1.2.1.1.1.9	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.1.1.1.10	Gauge32	read-only	The counter associated with the number of loss of continuity cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.11	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentSES	1.3.6.1.4.1.164.12.2.1.2.1.1.1.12	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentCDC	1.3.6.1.4.1.164.12.2.1.2.1.1.1.13	Gauge32	read-only	Amount of cells dropped in the current 15 minute interval of the VP connection.
G32 atmVpCurrentTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.14	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVpCurrentClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.15	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 and discarded by the traffic policing entity.
G32 atmVpCurrentTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.16	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVpCurrentClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVpCurrentTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.18	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVpCurrentPCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.19	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second).
G32 atmVpCurrentSCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.20	Gauge32	read-only	The average traffic rate during the last interval of the VP connection.
G32 atmVpCurrentMCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.21	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second).
G32 atmVpCurrentShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.22	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
G32 atmVpCurrentShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.23	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVpCurrentShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.24	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
atmVpPMCurrentTable	1.3.6.1.4.1.164.12.2.1.2.1.2		not-accessible	The ATM VP Current table for Performance Management.
atmVpPMCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.1.2.1		not-accessible	An entry in the ATM VP Current table for Performance Management.
I32 atmVpPMCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.1.2.1.1	Integer32	read-only	The VPI of the VPL.
INT atmVpPMCurrentDir	1.3.6.1.4.1.164.12.2.1.2.1.2.1.2	INTEGER	read-only	The direction of performance management.
G32 atmVpPMCurrentTxClp01	1.3.6.1.4.1.164.12.2.1.2.1.2.1.3	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentTxClp0	1.3.6.1.4.1.164.12.2.1.2.1.2.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentRxClp01	1.3.6.1.4.1.164.12.2.1.2.1.2.1.5	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentRxClp0	1.3.6.1.4.1.164.12.2.1.2.1.2.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentErroredCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.7	Gauge32	read-only	The counter associated with the number of errored cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentLostCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.8	Gauge32	read-only	The counter associated with the number of lost cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.9	Gauge32	read-only	The counter associated with the number of misinserted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentECB	1.3.6.1.4.1.164.12.2.1.2.1.2.1.10	Gauge32	read-only	The counter associated with the number of ECB, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentSECB	1.3.6.1.4.1.164.12.2.1.2.1.2.1.11	Gauge32	read-only	The counter associated with the number of SECB, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentES	1.3.6.1.4.1.164.12.2.1.2.1.2.1.12	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentSES	1.3.6.1.4.1.164.12.2.1.2.1.2.1.13	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.1.2.1.14	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
INT atmVpPMCurrentIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.1.2.1.15	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVpPMCurrentLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.1.2.1.16	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
atmVpIntervalTable	1.3.6.1.4.1.164.12.2.1.2.1.3		not-accessible	The ATM Vp Interval table.
atmVpIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.1.3.1		not-accessible	An entry in the ATM Vp Interval table.
I32 atmVpIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.1.3.1.1	Integer32	read-only	The VPI of the VPL.
I32 atmVpIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.1.3.1.2	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmVpIntervalRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.1.3.1.3	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.1.3.1.4	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.1.3.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.1.3.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxAIS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.7	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalTxAIS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.8	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.
G32 atmVpIntervalRxRDI	1.3.6.1.4.1.164.12.2.1.2.1.3.1.9	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalTxRDI	1.3.6.1.4.1.164.12.2.1.2.1.3.1.10	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.1.3.1.11	Gauge32	read-only	The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.12	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalSES	1.3.6.1.4.1.164.12.2.1.2.1.3.1.13	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalCDC	1.3.6.1.4.1.164.12.2.1.2.1.3.1.14	Gauge32	read-only	Amount of cells dropped in the 15 minute interval of the VP connection.
G32 atmVpIntervalTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.15	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVpIntervalClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.16	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVpIntervalTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVpIntervalClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVpIntervalTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.19	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVpIntervalPCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.20	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalSCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.21	Gauge32	read-only	The average traffic rate during the last interval of the VP connection , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalMCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.22	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.23	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
G32 atmVpIntervalShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.24	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVpIntervalShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.25	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
atmVpPMIntervalTable	1.3.6.1.4.1.164.12.2.1.2.1.4		not-accessible	The ATM Vp Interval table for Performance Management.
atmVpPMIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.1.4.1		not-accessible	An entry in the ATM Vp Interval table for Performance Management.
I32 atmVpPMIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.1.4.1.1	Integer32	read-only	The VPI of the VPL.
INT atmVpPMIntervalDir	1.3.6.1.4.1.164.12.2.1.2.1.4.1.2	INTEGER	read-only	The direction of performance management.
I32 atmVpPMIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.1.4.1.3	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmVpPMIntervalTxClp01	1.3.6.1.4.1.164.12.2.1.2.1.4.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalTxClp0	1.3.6.1.4.1.164.12.2.1.2.1.4.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalRxClp01	1.3.6.1.4.1.164.12.2.1.2.1.4.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalRxClp0	1.3.6.1.4.1.164.12.2.1.2.1.4.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalErroredCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.8	Gauge32	read-only	The counter associated with the number of Errored cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalLostCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.9	Gauge32	read-only	The counter associated with the number of Lost cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.10	Gauge32	read-only	The counter associated with the number of Misinserted cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalECB	1.3.6.1.4.1.164.12.2.1.2.1.4.1.11	Gauge32	read-only	The counter associated with the number of ECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalSECB	1.3.6.1.4.1.164.12.2.1.2.1.4.1.12	Gauge32	read-only	The counter associated with the number of SECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalES	1.3.6.1.4.1.164.12.2.1.2.1.4.1.13	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalSES	1.3.6.1.4.1.164.12.2.1.2.1.4.1.14	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.1.4.1.15	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
INT atmVpPMIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.1.4.1.16	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVpPMIntervalLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.1.4.1.17	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
atmVpQoSTable	1.3.6.1.4.1.164.12.2.1.2.1.5		not-accessible	The VP QoS table.
atmVpQoSEntry	1.3.6.1.4.1.164.12.2.1.2.1.5.1		not-accessible	.
INT atmVpQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.1.5.1.1	INTEGER	read-only	This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
I32 atmVpQoSElapsedTime	1.3.6.1.4.1.164.12.2.1.2.1.5.1.2	Integer32	read-only	Elapsed Time in seconds. - for atmVpQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVpQoSPeriodRef = lastPeriod: The value of atmVpQoSElapsedTime when last systemResetAllStatsCmd was received.
G32 atmVpQoSUAS	1.3.6.1.4.1.164.12.2.1.2.1.5.1.3	Gauge32	read-only	Number of Unavailable Seconds for the reference period (atmVpQoSPeriodRef).
atmVpPMQoSTable	1.3.6.1.4.1.164.12.2.1.2.1.6		not-accessible	The PM VP QoS table.
atmVpPMQoSEntry	1.3.6.1.4.1.164.12.2.1.2.1.6.1		not-accessible	.
INT atmVpPMQoSDirection	1.3.6.1.4.1.164.12.2.1.2.1.6.1.1	INTEGER	read-only	The direction of performance management.
INT atmVpPMQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.1.6.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
G32 atmVpPMQoSCLR	1.3.6.1.4.1.164.12.2.1.2.1.6.1.3	Gauge32	read-only	Cell Loss Ratio counter for the reference period (atmVpPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVpPMQoSCER	1.3.6.1.4.1.164.12.2.1.2.1.6.1.4	Gauge32	read-only	Cell Error Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVpPMQoSCMR	1.3.6.1.4.1.164.12.2.1.2.1.6.1.5	Gauge32	read-only	Cell Misinsertion Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .
atmVpShaperStatTable	1.3.6.1.4.1.164.12.2.1.2.1.7		not-accessible	The ATM VP shaper statistics table.
atmVpShaperStatEntry	1.3.6.1.4.1.164.12.2.1.2.1.7.1		not-accessible	An entry in the ATM VP shaper statistics table.
C32 atmVpShaperDiscarded	1.3.6.1.4.1.164.12.2.1.2.1.7.1.1	Counter32	read-only	The number of Cells that were discarded in the shaper on that VPC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.
I32 atmVpShaperOccupation	1.3.6.1.4.1.164.12.2.1.2.1.7.1.2	Integer32	read-only	The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.
I32 atmVpShaperMaxOccupation	1.3.6.1.4.1.164.12.2.1.2.1.7.1.3	Integer32	read-only	The Maximum number of Cells that were stored in the buffer, since this VP was activated. This parameter is limited to 20 bits.
INT atmVpShaperLevel	1.3.6.1.4.1.164.12.2.1.2.1.7.1.4	INTEGER	read-only	The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VPC.
C32 atmVpShaperEpdDropped	1.3.6.1.4.1.164.12.2.1.2.1.7.1.5	Counter32	read-only	The number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VP only.
C32 atmVpShaperTotalEpdDropped	1.3.6.1.4.1.164.12.2.1.2.1.7.1.6	Counter32	read-only	The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VP only.
atmVcPerformance	1.3.6.1.4.1.164.12.2.1.2.2
atmVcCurrentTable	1.3.6.1.4.1.164.12.2.1.2.2.1		not-accessible	The ATM VC Current table.
atmVcCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.2.1.1		not-accessible	An entry in the ATM VC Current table.
I32 atmVcCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.2.1.1.1	Integer32	read-only	The VPI of the VCL.
I32 atmVcCurrentVci	1.3.6.1.4.1.164.12.2.1.2.2.1.1.2	Integer32	read-only	The VCI of the VCL.
G32 atmVcCurrentRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.2.1.1.3	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.2.1.1.4	Gauge32	read-only	The counter associated with the number of received cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.2.1.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.2.1.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentRxAIS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.7	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentTxAIS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.8	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.
G32 atmVcCurrentRxRDI	1.3.6.1.4.1.164.12.2.1.2.2.1.1.9	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentTxRDI	1.3.6.1.4.1.164.12.2.1.2.2.1.1.10	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.2.1.1.11	Gauge32	read-only	The counter associated with the number of loss of continuity cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.12	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentSES	1.3.6.1.4.1.164.12.2.1.2.2.1.1.13	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentCDC	1.3.6.1.4.1.164.12.2.1.2.2.1.1.14	Gauge32	read-only	Amount of cells dropped in the current 15 minute interval of the VC connection.
G32 atmVcCurrentTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.15	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVcCurrentClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.16	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVcCurrentTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVcCurrentClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVcCurrentTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.19	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVcCurrentPCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.20	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second).
G32 atmVcCurrentSCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.21	Gauge32	read-only	The average traffic rate during the last interval of the VC connection.
G32 atmVcCurrentMCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.22	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second).
G32 atmVcCurrentShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.23	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
G32 atmVcCurrentShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.24	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVcCurrentShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.25	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
atmVcPMCurrentTable	1.3.6.1.4.1.164.12.2.1.2.2.2		not-accessible	The ATM VC Current table for Performance Management.
atmVcPMCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.2.2.1		not-accessible	An entry in the ATM VC Current table for Performance Management.
I32 atmVcPMCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.2.2.1.1	Integer32	read-only	The VPI of the VCL.
I32 atmVcPMCurrentVci	1.3.6.1.4.1.164.12.2.1.2.2.2.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcPMCurrentDir	1.3.6.1.4.1.164.12.2.1.2.2.2.1.3	Integer32	read-only	The direction of Performance Management.
G32 atmVcPMCurrentTxClp01	1.3.6.1.4.1.164.12.2.1.2.2.2.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentTxClp0	1.3.6.1.4.1.164.12.2.1.2.2.2.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentRxClp01	1.3.6.1.4.1.164.12.2.1.2.2.2.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentRxClp0	1.3.6.1.4.1.164.12.2.1.2.2.2.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentErroredCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.8	Gauge32	read-only	The counter associated with the number of errored cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentLostCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.9	Gauge32	read-only	The counter associated with the number of lost cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.10	Gauge32	read-only	The counter associated with the number of misinserted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentECB	1.3.6.1.4.1.164.12.2.1.2.2.2.1.11	Gauge32	read-only	The counter associated with the number of ECBs encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentSECB	1.3.6.1.4.1.164.12.2.1.2.2.2.1.12	Gauge32	read-only	The counter associated with the number of SECBs encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentES	1.3.6.1.4.1.164.12.2.1.2.2.2.1.13	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentSES	1.3.6.1.4.1.164.12.2.1.2.2.2.1.14	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.2.2.1.15	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
INT atmVcPMCurrentIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.2.2.1.16	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVcPMCurrentLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.2.2.1.17	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
atmVcIntervalTable	1.3.6.1.4.1.164.12.2.1.2.2.3		not-accessible	The ATM Vc Interval table.
atmVcIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.2.3.1		not-accessible	An entry in the ATM Vc Interval table.
I32 atmVcIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.2.3.1.1	Integer32	read-only	The VPI of the VCL.
I32 atmVcIntervalVci	1.3.6.1.4.1.164.12.2.1.2.2.3.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.2.3.1.3	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmVcIntervalRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.2.3.1.4	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.2.3.1.5	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.2.3.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.2.3.1.7	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxAIS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.8	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalTxAIS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.9	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.
G32 atmVcIntervalRxRDI	1.3.6.1.4.1.164.12.2.1.2.2.3.1.10	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalTxRDI	1.3.6.1.4.1.164.12.2.1.2.2.3.1.11	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.2.3.1.12	Gauge32	read-only	The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.13	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalSES	1.3.6.1.4.1.164.12.2.1.2.2.3.1.14	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalCDC	1.3.6.1.4.1.164.12.2.1.2.2.3.1.15	Gauge32	read-only	Amount of cells dropped in the 15 minute interval of the VC connection.
G32 atmVcIntervalTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.16	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVcIntervalClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.17	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVcIntervalTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVcIntervalClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.19	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVcIntervalTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.20	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVcIntervalPCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.21	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalSCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.22	Gauge32	read-only	The average traffic rate during the last interval of the VC connection, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalMCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.23	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.24	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
G32 atmVcIntervalShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.25	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVcIntervalShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.26	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
atmVcPMIntervalTable	1.3.6.1.4.1.164.12.2.1.2.2.4		not-accessible	The ATM Vc Interval table for Performance Management.
atmVcPMIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.2.4.1		not-accessible	An entry in the ATM Vc Interval table for Performance Management.
I32 atmVcPMIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.2.4.1.1	Integer32	read-only	The VPI of the VCL.
I32 atmVcPMIntervalVci	1.3.6.1.4.1.164.12.2.1.2.2.4.1.2	Integer32	read-only	The VCI of the VCL.
INT atmVcPMIntervalDir	1.3.6.1.4.1.164.12.2.1.2.2.4.1.3	INTEGER	read-only	The direction of Performance Management.
I32 atmVcPMIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.2.4.1.4	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmVcPMIntervalTxClp01	1.3.6.1.4.1.164.12.2.1.2.2.4.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalTxClp0	1.3.6.1.4.1.164.12.2.1.2.2.4.1.6	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalRxClp01	1.3.6.1.4.1.164.12.2.1.2.2.4.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalRxClp0	1.3.6.1.4.1.164.12.2.1.2.2.4.1.8	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalErroredCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.9	Gauge32	read-only	The counter associated with the number of Errored cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalLostCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.10	Gauge32	read-only	The counter associated with the number of Lost cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.11	Gauge32	read-only	The counter associated with the number of Misinserted cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalECB	1.3.6.1.4.1.164.12.2.1.2.2.4.1.12	Gauge32	read-only	The counter associated with the number of ECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalSECB	1.3.6.1.4.1.164.12.2.1.2.2.4.1.13	Gauge32	read-only	The counter associated with the number of SECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalES	1.3.6.1.4.1.164.12.2.1.2.2.4.1.14	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalSES	1.3.6.1.4.1.164.12.2.1.2.2.4.1.15	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.2.4.1.16	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
INT atmVcPMIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.2.4.1.17	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVcPMIntervalLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.2.4.1.18	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
atmVcQoSTable	1.3.6.1.4.1.164.12.2.1.2.2.6		not-accessible	The ATM VP QoS table.
atmVcQoSEntry	1.3.6.1.4.1.164.12.2.1.2.2.6.1		not-accessible	An entry in the ATM VP table.
INT atmVcQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.2.6.1.1	INTEGER	read-only	This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
I32 atmVcQoSElapsedTime	1.3.6.1.4.1.164.12.2.1.2.2.6.1.2	Integer32	read-only	Elapsed Time in seconds. - for atmVcQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVcQoSPeriodRef = lastPeriod: The value of atmVcQoSElapsedTime when last systemResetAllStatsCmd was received.
G32 atmVcQoSUAS	1.3.6.1.4.1.164.12.2.1.2.2.6.1.3	Gauge32	read-only	Number of Unavailable Seconds for the reference period (atmVcQoSPeriodRef).
atmVcPMQoSTable	1.3.6.1.4.1.164.12.2.1.2.2.7		not-accessible	The PM VC QoS table.
atmVcPMQoSEntry	1.3.6.1.4.1.164.12.2.1.2.2.7.1		not-accessible	An entry in the VC PM QoS table.
INT atmVcPMQoSDirection	1.3.6.1.4.1.164.12.2.1.2.2.7.1.1	INTEGER	read-only	The direction of performance management.
INT atmVcPMQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.2.7.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
G32 atmVcPMQoSCLR	1.3.6.1.4.1.164.12.2.1.2.2.7.1.3	Gauge32	read-only	Cell Loss Ratio counter for the reference period (atmVcPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVcPMQoSCER	1.3.6.1.4.1.164.12.2.1.2.2.7.1.4	Gauge32	read-only	Cell Error Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVcPMQoSCMR	1.3.6.1.4.1.164.12.2.1.2.2.7.1.5	Gauge32	read-only	Cell Miss-insertion Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .
atmVcShaperStatTable	1.3.6.1.4.1.164.12.2.1.2.2.8		not-accessible	The ATM VC shaper statistics table.
atmVcShaperStatEntry	1.3.6.1.4.1.164.12.2.1.2.2.8.1		not-accessible	An entry in the ATM VC shaper statistics table.
C32 atmVcShaperDiscarded	1.3.6.1.4.1.164.12.2.1.2.2.8.1.1	Counter32	read-only	The number of Cells that were discarded in the shaper on that VCC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.
I32 atmVcShaperOccupation	1.3.6.1.4.1.164.12.2.1.2.2.8.1.2	Integer32	read-only	The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.
I32 atmVcShaperMaxOccupation	1.3.6.1.4.1.164.12.2.1.2.2.8.1.3	Integer32	read-only	The Maximum number of Cells that were stored in the buffer, since this VC was activated. This parameter is limited to 20 bits.
INT atmVcShaperLevel	1.3.6.1.4.1.164.12.2.1.2.2.8.1.4	INTEGER	read-only	The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VCC.
C32 atmVcShaperEpdDropped	1.3.6.1.4.1.164.12.2.1.2.2.8.1.5	Counter32	read-only	The number of Cells that were dropped in the shaper on that VCC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VC only.
C32 atmVcShaperTotalEpdDropped	1.3.6.1.4.1.164.12.2.1.2.2.8.1.6	Counter32	read-only	The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VC only.
atmIntervalDateTable	1.3.6.1.4.1.164.12.2.1.3		not-accessible	The agent will keep in this group the date & time corresponding to each interval.
atmIntervalDateEntry	1.3.6.1.4.1.164.12.2.1.3.1		not-accessible	The date & time for the given interval.
I32 atmIntervalDateInterval	1.3.6.1.4.1.164.12.2.1.3.1.1	Integer32	read-only	The interval number defining this entry.
STR atmIntervalDateDate	1.3.6.1.4.1.164.12.2.1.3.1.2	DisplayString	read-only	The date corresponding to this interval.
STR atmIntervalDateTime	1.3.6.1.4.1.164.12.2.1.3.1.3	DisplayString	read-only	The time corresponding to this interval.
atmGenSystem	1.3.6.1.4.1.164.12.2.2
atmGenSysGen	1.3.6.1.4.1.164.12.2.2.1
atmGenSysSelfTestTable	1.3.6.1.4.1.164.12.2.2.1.1		not-accessible	A table containing the results of the initial testing of the device.
atmGenSysSelfTestEntry	1.3.6.1.4.1.164.12.2.2.1.1.1		not-accessible	An entry in table.
I32 atmGenSysSelfTestIndex	1.3.6.1.4.1.164.12.2.2.1.1.1.1	Integer32	read-only	A running index for the table.
STR atmGenSysSelfTestResult	1.3.6.1.4.1.164.12.2.2.1.1.1.2	DisplayString	read-only	The results of the initial testing of the device.
STR atmGenSysSelfTestModule	1.3.6.1.4.1.164.12.2.2.1.1.1.3	DisplayString	read-only	The name of module on which the test was performed.
INT atmGenSysLogClearAll	1.3.6.1.4.1.164.12.2.2.1.2	INTEGER	read-write	Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).
atmGenSysLogTable	1.3.6.1.4.1.164.12.2.2.1.3		not-accessible	A copy of the log buffer.
atmGenSysLogEntry	1.3.6.1.4.1.164.12.2.2.1.3.1		not-accessible	An entry in table.
I32 atmGenSysLogIndex	1.3.6.1.4.1.164.12.2.2.1.3.1.1	Integer32	read-only	The index of the log buffer.
STR atmGenSysLogMessage	1.3.6.1.4.1.164.12.2.2.1.3.1.2	DisplayString	read-only	The log buffer entry message text.
INT atmGenSysSetDefaultConfg	1.3.6.1.4.1.164.12.2.2.1.4	INTEGER	read-write	When set to on(3), the agent will set all the configuration parameters to their default values. The variable is then reset to off(2) by the agent. The agent must be reset for the default configuration to apply.
atmGenSysCxRefTable	1.3.6.1.4.1.164.12.2.2.1.5		not-accessible	A Cross Reference table. The table maintains an index of an object which is also the table index, and a counter that indicates how many times this object was referenced. When using this table for more than one referenced table, which uses the same range of indexes, then the index should be shifted by a unique offset per table. In ACE2002 this table is used for TD and for FR Desc. Thus, the index for FR Descriptor is: FR Descriptor index + offset. The offset is described in the ACE2002 NMS SRS.
atmGenSysCxRefEntry	1.3.6.1.4.1.164.12.2.2.1.5.1		not-accessible	The entries will be added by the agent upon an entry addition in the referenced tables (TD table, FR Descriptor etc.)
I32 atmGenSysCxRefIndex	1.3.6.1.4.1.164.12.2.2.1.5.1.1	Integer32	read-only	The index specifies an entry in the table of the object.
G32 atmGenSysCxRefCounter	1.3.6.1.4.1.164.12.2.2.1.5.1.2	Gauge32	read-only	The counter counts the number of references that have been made to the object .
atmNte	1.3.6.1.4.1.164.12.3
atmNteEvents	1.3.6.1.4.1.164.12.3.0			The events for RAD ATM products.
NTF atmAceStatusChange	1.3.6.1.4.1.164.12.3.0.1			The trap is sent every time there is a change in the state of one of the LEDs.
NTF atmAceAlarmTrap	1.3.6.1.4.1.164.12.3.0.2			The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm. An active alarm state exists if: 1) The atmInterfaceActiveAlarms vector is different than 0. 2) The atmNteAlarmVpTable contains entries. 3) The atmNteAlarmVcTable contains entries. The trap is also sent when a transition into the no alarm state occurs. The second variable will be atmInterfaceActiveAlarms to indicate the kind of the alarm. The trap is not sent more than once in a 10 second interval.
NTF atmAceModuleChangeTrap	1.3.6.1.4.1.164.12.3.0.3			The trap is sent every time a module is changed (Hot swapping). The second variable will be atmNteCardType to indicate the type of card that was inserted. The value empty(255) indicates that a card was taken out.
NTF atmAceRedundancyTrap	1.3.6.1.4.1.164.12.3.0.4			The trap is sent upon change in link as a result of redundancy. The ifIndex parameter indicates the current active link.
NTF atmAceModuleMismatchTrap	1.3.6.1.4.1.164.12.3.0.5			The trap is sent upon starting or stopping of a module mismatch state. A possible mismatch is when the inserted module is other than the programmed one.
atmNteSys	1.3.6.1.4.1.164.12.3.1
atmNteSysConfig	1.3.6.1.4.1.164.12.3.1.1
atmNteManagerTable	1.3.6.1.4.1.164.12.3.1.1.1		not-accessible	The Manager Table includes all the NMSs that receive traps from this agent. A single manager can receive traps on more than one PVC. The agent will set implicitly the correct ifIndex, VPI, VCI values to all relevant entries in the table when the user changes them for one of the PVCs.
atmNteManagerEntry	1.3.6.1.4.1.164.12.3.1.1.1.1		not-accessible	A single manager and the PVC for receiving traps.
IP atmNteManagerIP	1.3.6.1.4.1.164.12.3.1.1.1.1.1	IpAddress	read-only	The IP address of the NMS.
I32 atmNteManagerPvc	1.3.6.1.4.1.164.12.3.1.1.1.1.2	Integer32	read-only	A PVC index. The range is 1..8. There are four PVCs on the User Port and four PVCs on the Network Port. The default VPI, VCI values are specified below.
I32 atmNteManagerIfIndex	1.3.6.1.4.1.164.12.3.1.1.1.1.3	Integer32	read-create	The ATM interface index of the management port.
I32 atmNteManagerVpi	1.3.6.1.4.1.164.12.3.1.1.1.1.4	Integer32	read-create	The VPI of the management VCL. Default: 0.
I32 atmNteManagerVci	1.3.6.1.4.1.164.12.3.1.1.1.1.5	Integer32	read-create	The VCI of the management VCL. Defaults: 32,33,34,35.
I32 atmNteManagerTrapMask	1.3.6.1.4.1.164.12.3.1.1.1.1.6	Integer32	read-create	The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
ROW atmNteManagerRowStatus	1.3.6.1.4.1.164.12.3.1.1.1.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
IP atmNteManagerNextHop	1.3.6.1.4.1.164.12.3.1.1.1.1.8	IpAddress	read-create	This parameter is relevant to Ethernet out of band host only (PVC=10). The Next Hop IP address of the entry route.
INT atmNteManagerVlanSupport	1.3.6.1.4.1.164.12.3.1.1.1.1.9	INTEGER	read-create	VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
I32 atmNteManagerVlanIdentifier	1.3.6.1.4.1.164.12.3.1.1.1.1.10	Integer32	read-create	VLAN ID. Range is 0..4095.
I32 atmNteManagerVlanFramePriority	1.3.6.1.4.1.164.12.3.1.1.1.1.11	Integer32	read-create	VLAN Frame priority.Range is 0..7.
OCT atmNteManagerAlarmTrapMask	1.3.6.1.4.1.164.12.3.1.1.1.1.12	OCTET STRING	read-create	The value of this object determines the alarm traps that the agent should mask and not send to this NMS. The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. More details on the masked traps exist in the product specification. For products that do not mask specific traps, the value of the bits will be 0.
I32 atmNteManagerConfigPorts	1.3.6.1.4.1.164.12.3.1.1.1.1.13	Integer32	read-create	This variable defines from which port/s this manager can configure the device. For IPmux 11 the value of this variable will be according to the ports combination: Network =1 User1=2 User2=4 (For Example: All ports = 7).
I32 atmNteUPLTCR	1.3.6.1.4.1.164.12.3.1.1.2	Integer32	read-write	The Unacceptable ES Limit threshold for Performance Management.
I32 atmNteDPLTCR	1.3.6.1.4.1.164.12.3.1.1.3	Integer32	read-write	The Degraded ES Limit threshold for Performance Management.
INT atmNteSysLogClearAll	1.3.6.1.4.1.164.12.3.1.1.4	INTEGER	read-write	Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).
I32 atmNteUSESLTCR	1.3.6.1.4.1.164.12.3.1.1.5	Integer32	read-write	The Unacceptable SES Limit threshold for Performance Management.
I32 atmNteDSESLTCR	1.3.6.1.4.1.164.12.3.1.1.6	Integer32	read-write	The Degraded ES Limit threshold for Performance Management.
atmNteProtection	1.3.6.1.4.1.164.12.3.1.1.8
INT atmNteProtectionMode	1.3.6.1.4.1.164.12.3.1.1.8.1	INTEGER	read-write	Protection Mode. MspOn - Multiplex section protection. pathOn - High order path protection. mspUniOn - Multiplex section Uni-directional protection. mspOneToN - Multiplex section protection.
INT atmNteProtectionWorkingLink	1.3.6.1.4.1.164.12.3.1.1.8.2	INTEGER	read-write	Selects the working link when atmNteProtectionMode is off.
INT atmNteProtectionSwitchLink	1.3.6.1.4.1.164.12.3.1.1.8.3	INTEGER	read-write	ForceSwitch - will force Switching from the working link to the backup link. Afterwards the agent will set atmNteProtectionSwitchLink back to off(1). atmNteProtectionMode must be either mspOn or pathOn.
atmNteConfOam	1.3.6.1.4.1.164.12.3.1.1.9
INT atmNteConfOamSupport	1.3.6.1.4.1.164.12.3.1.1.9.1	INTEGER	read-write	OAM support mode, which determines the device location in a segment wise.
atmNteConfOamTransmission	1.3.6.1.4.1.164.12.3.1.1.9.2
INT atmNteConfOamAIS	1.3.6.1.4.1.164.12.3.1.1.9.2.1	INTEGER	read-write	Defines if a F4 segment OAM cell is transmitted due to problems in the other port, i.e. physical layer alarm or F4 defect. This is valid only when the ACE101 has ATM UNI interfaces in both sides and is configured for 'Non-Intrusive' mode. none - AIS is not sent to any of the ports. user - F4 AIS will be sent toward the user when defect is detected in the network port. network - F4 AIS will be sent toward the network when defect is detected in the user port. both - F4 AIS will be sent toward the network when defect is detected in the user port and toward the user when defect is detected in the network port.
INT atmNteConfOamRDI	1.3.6.1.4.1.164.12.3.1.1.9.2.2	INTEGER	read-write	Defines if an F4 OAM RDI cell is transmitted due to physical layer problems in the port (in addition to F4 RDI cells transmitted due to ATM layer problems). The type of F4 RDI (Segment or End-to-End) is according to the ACE-101 OAM mode. For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4 RDI cell back to the trunk.
atmNteConfOamAddressing	1.3.6.1.4.1.164.12.3.1.1.9.3
INT atmNteConfLoopbackAddMode	1.3.6.1.4.1.164.12.3.1.1.9.3.1	INTEGER	read-write	Loopback addressing mode. on - will enable loopback addressing. off - will disable loopback addressing.
OCT atmNteConfLoopbackSourceAdd	1.3.6.1.4.1.164.12.3.1.1.9.3.2	OCTET STRING	read-write	Loopback source address. This field is relevant when atmNteConfOamAddMode is on.
atmNteConfOamIfTable	1.3.6.1.4.1.164.12.3.1.1.9.4		not-accessible	OAM support per ATM interface.
atmNteConfOamIfEntry	1.3.6.1.4.1.164.12.3.1.1.9.4.1		not-accessible	.
INT atmNteConfOamIfAisRdi	1.3.6.1.4.1.164.12.3.1.1.9.4.1.1	INTEGER	read-write	This parameter controls the generation of F4/F5 AIS and RDI due to lower order problems such as physical layer problems. For AIS: Defines if F4/F5 AIS cell is transmitted due to problems such as physical layer alarm or F4/F5 defect. This is applicable for all ports . off - Problems in this port will not trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. on - Problems in this port will trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. For RDI: Defines if F4/F5 RDI cell will be transmitted due to physical layer problems in that port (in addition to F4/F5 RDI cells transmitted due to ATM layer problems). For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4/F5 RDI cell back to the trunk. The type of F4/F5 (Segment or End-to-End) is according to the configuration of the VPC/VCC.
atmNteConfCAC	1.3.6.1.4.1.164.12.3.1.1.10
INT atmNteConfCACMode	1.3.6.1.4.1.164.12.3.1.1.10.1	INTEGER	read-write	CAC support mode. For ACE2002, the following are the applicable values: disable(1), enable(2), 10 - 1000.
atmNteHostIfTable	1.3.6.1.4.1.164.12.3.1.1.11		not-accessible	Host IP interface table.
atmNteHostIfEntry	1.3.6.1.4.1.164.12.3.1.1.11.1		not-accessible	.
I32 atmNteHostPvcIndex	1.3.6.1.4.1.164.12.3.1.1.11.1.1	Integer32	read-only	A PVC index. The range is 1..10.
IP atmNteHostIP	1.3.6.1.4.1.164.12.3.1.1.11.1.2	IpAddress	read-create	The host interface IP address.
IP atmNteHostMask	1.3.6.1.4.1.164.12.3.1.1.11.1.3	IpAddress	read-create	The host interface subnet mask.
I32 atmNteHostAtmIfIndex	1.3.6.1.4.1.164.12.3.1.1.11.1.4	Integer32	read-create	ATM interface index. Will be 1 for user port, and 2 for network port.
I32 atmNteHostVpi	1.3.6.1.4.1.164.12.3.1.1.11.1.5	Integer32	read-create	VPI of the PVC connected to that host interface.
I32 atmNteHostVci	1.3.6.1.4.1.164.12.3.1.1.11.1.6	Integer32	read-create	VCI of the PVC connected to that host interface.
ROW atmNteHostRowStatus	1.3.6.1.4.1.164.12.3.1.1.11.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
I32 atmNteHostRdnVpi	1.3.6.1.4.1.164.12.3.1.1.11.1.8	Integer32	read-create	The VPI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).
I32 atmNteHostRdnVci	1.3.6.1.4.1.164.12.3.1.1.11.1.9	Integer32	read-create	The VCI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).
IP atmNteHostDefaultNextHop	1.3.6.1.4.1.164.12.3.1.1.11.1.10	IpAddress	read-create	The host interface Default Next Hop address. This address will be used as default next hop for every Bundle mapped to this Host.
INT atmNteHostVlanTagging	1.3.6.1.4.1.164.12.3.1.1.11.1.11	INTEGER	read-create	VLAN Tag support. no - No support to VLAN. yes - 4 VLAN bytes will be added to each frame connected to this Host.
I32 atmNteHostDefaultVlanID	1.3.6.1.4.1.164.12.3.1.1.11.1.12	Integer32	read-create	Default VLAN ID of this Host.
I32 atmNteHostDefaultVlanPriority	1.3.6.1.4.1.164.12.3.1.1.11.1.13	Integer32	read-create	Default VLAN priority for this Host.
INT atmNteShaperMode	1.3.6.1.4.1.164.12.3.1.1.12	INTEGER	read-write	Shaper Mode. vpInbandMng - Vcc within a Vp for management.
I32 atmNteOutputRate	1.3.6.1.4.1.164.12.3.1.1.13	Integer32	read-write	Aggregate shaping output rate in Cells per Seconds units. Default value is the Network port rate.
INT atmNteTosMode	1.3.6.1.4.1.164.12.3.1.1.14	INTEGER	read-write	TOS Mode.
OCT atmNteTosMask	1.3.6.1.4.1.164.12.3.1.1.15	OCTET STRING	read-write	This parameter determines the seqence of bits that will be used for TOS. For ACE101 this parameter is applicable only if atmNteTosMode = enable. Valid only for IP-TOS process.
OCT atmNteTosHighPriority	1.3.6.1.4.1.164.12.3.1.1.16	OCTET STRING	read-write	Priorities options are High or Low. High priority will be represented by bit = 1. Low priority will be represented by bit = 0. Each TOS value will be represented by the bit location. For example, the string for TOS 2, 9, 15 with High priority, will be: \|0000 0000\|... ...\|0000 0000\|1000 0010\|0000 0100\| ...98 7654 3210 (Bit #) 8 ... 3 2 1 (Byte #).
INT atmNtePlugAndPlayActivity	1.3.6.1.4.1.164.12.3.1.1.17	INTEGER	read-write	Activity control for Manager Plug And Play. disable - disable the feature. offline - Automatic learn IP address into offline memory. online - Automatic learn IP address into online memory.
INT atmNteSlotUsage	1.3.6.1.4.1.164.12.3.1.1.18	INTEGER	read-write	Applicable to ace2002. Slot 2 might be configured as user slot or as network slot.
INT atmNteConnectionsMaxNumber	1.3.6.1.4.1.164.12.3.1.1.19	INTEGER	read-write	The MAX number of connections supported by system. Setting this parameter will affect the number of MAX intervals supported. This parameter will affect the system only after reset. Changing this parameter from high value to a low value, will be accepted by agent only if the actual used connection <= the desired connection Max number. Applicable to ace2002.
I32 atmNteDefaultVpi	1.3.6.1.4.1.164.12.3.1.1.20	Integer32	read-write	Default Vpi for management.
I32 atmNteDefaultVci	1.3.6.1.4.1.164.12.3.1.1.21	Integer32	read-write	Default Vci for management.
I32 atmNteReservedVpi	1.3.6.1.4.1.164.12.3.1.1.22	Integer32	read-write	Internal use VPI, where shaperMode=vpInbandMng.
INT atmNteRdnManagement	1.3.6.1.4.1.164.12.3.1.1.23	INTEGER	read-only	The redundancy management status.
NUM atmNtePlugAndPlayIfIndex	1.3.6.1.4.1.164.12.3.1.1.24	InterfaceIndex	read-write	The ifIndex of the Plug and Play VCC.
I32 atmNteLoopbackTimeout	1.3.6.1.4.1.164.12.3.1.1.25	Integer32	read-write	The Loopback state timeout in minutes. A value of zero means no timeout (for ever). Default is 5 min.
atmNteOamTable	1.3.6.1.4.1.164.12.3.1.1.26		not-accessible	This table is a static table, which is created by agent once upon initialization. The created entries are actually, only the supported OAM features. This table enables addition of new features by adding new entries rather than adding scalar parameters. An OAM feature is defined by the indexes values combination.
atmNteOamEntry	1.3.6.1.4.1.164.12.3.1.1.26.1		not-accessible	An entry in the OAM table. Each entry in this table will indicate a special OAM.
INT atmNteOamMode	1.3.6.1.4.1.164.12.3.1.1.26.1.1	INTEGER	read-only	The OAM cell path. endToEnd(1) - the entire path.
INT atmNteOamCellType	1.3.6.1.4.1.164.12.3.1.1.26.1.2	INTEGER	read-only	This object indicates a unique Indication Signal. aisAndRdi(1) - Alarm Indication Signal (AIS) and Remote Defect Indication (RDI) cell. loopback(2) - Loopback cell.
INT atmNteOamLevel	1.3.6.1.4.1.164.12.3.1.1.26.1.3	INTEGER	read-only	The level of the OAM cell. -- f4 (2) - VP level, f5 (3) - VC level.
INT atmNteOamEnable	1.3.6.1.4.1.164.12.3.1.1.26.1.4	INTEGER	read-write	This parameter determines if the specified OAM cells will be enabled.
I32 atmNteDefaultLoopbackThreshold	1.3.6.1.4.1.164.12.3.1.1.27	Integer32	read-write	The Default OAM Loopback Failure Threshold value that will be used for configuration.
I32 atmNteMaxBurstSize	1.3.6.1.4.1.164.12.3.1.1.28	Integer32	read-write	The Maximum allowed burst size (cell units). This object is applicable for each Physical port.
I32 atmNteGranularityFactor	1.3.6.1.4.1.164.12.3.1.1.29	Integer32	read-write	This parameter affects the granularity of the guaranteed Rate (SCR+MCR) in spaced connection (cell/sec units). It is also defines the minimum guaranteed rate in spaced connection.
I32 atmNteTotalInputRate	1.3.6.1.4.1.164.12.3.1.1.30	Integer32	read-only	This parameter indicates the total input rate of the device in cells/sec.
I32 atmNteTotalOutputRate	1.3.6.1.4.1.164.12.3.1.1.31	Integer32	read-only	This parameter indicates the total output rate of the device in cells/sec.
atmAlarmForwardingTable	1.3.6.1.4.1.164.12.3.1.1.32		not-accessible	The Alarm Forwarding Mechanism will be operated for this table entries.
atmAlarmForwardingEntry	1.3.6.1.4.1.164.12.3.1.1.32.1		not-accessible	Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.
I32 atmAlarmForwardingFailPort	1.3.6.1.4.1.164.12.3.1.1.32.1.1	Integer32	not-accessible	An Index of the port on which a fail occurs.
I32 atmAlarmForwardingToPort	1.3.6.1.4.1.164.12.3.1.1.32.1.2	Integer32	not-accessible	An Index of the port that will be affected upon the failure of the atmAlarmForwardingFailPort.
ROW atmAlarmForwardingRowStatus	1.3.6.1.4.1.164.12.3.1.1.32.1.3	RowStatus	read-create	Creation/Deletion of rows in the table.
BIT atmAlarmForwardingFailureLevel	1.3.6.1.4.1.164.12.3.1.1.32.1.4	Bits	read-create	This parameter determines the level of failure that will operate the Alarm Forwarding Mechanism.
INT atmAlarmForwardingRecoveryMode	1.3.6.1.4.1.164.12.3.1.1.32.1.5	INTEGER	read-create	This parameter determines the Recovery Mode. manual - The user should stop the RDI transmission by using the atmAlarmForwardingRecoveryCommand. automatic - The RDI transmission will be automatically stopped upon atmAlarmForwardingFailPort recovery.
INT atmAlarmForwardingRecoveryCommand	1.3.6.1.4.1.164.12.3.1.1.32.1.6	INTEGER	read-create	This parameter is a command. It is applicable when atmAlarmForwardingRecoveryMode = manual. on - Will stop the RDI transmission. After setting to 'On' the agent will set this parameter back to 'Off'.
U32 atmAlarmForwardingTimeFilterWindow	1.3.6.1.4.1.164.12.3.1.1.32.1.7	Unsigned32	read-create	This parameter determines the Time Filter Window, meaning: how much time (in seconds) should the alarm exist in order to start the Alarm Forwarding operation.
atmSysConfigCellTest	1.3.6.1.4.1.164.12.3.1.1.33
NUM atmSysConfigCellTestPort	1.3.6.1.4.1.164.12.3.1.1.33.1	InterfaceIndex	read-write	An Index of the port on which the cell test will be sent.
I32 atmSysConfigCellTestVpi	1.3.6.1.4.1.164.12.3.1.1.33.2	Integer32	read-write	The VPI on which the cell test will be sent.
I32 atmSysConfigCellTestVci	1.3.6.1.4.1.164.12.3.1.1.33.3	Integer32	read-write	The VCI on which the cell test will be sent.
INT atmSysConfigCellTestPti	1.3.6.1.4.1.164.12.3.1.1.33.4	INTEGER	read-write	The cell type.
INT atmSysConfigCellTestClp	1.3.6.1.4.1.164.12.3.1.1.33.5	INTEGER	read-write	The type of the Cell.
INT atmSysConfigCellTestOamType	1.3.6.1.4.1.164.12.3.1.1.33.6	INTEGER	read-write	The OAM type of the Cell. This object is applicable if atmSysConfigCellTestPti = oamSegment/oamEndToEnd .
OCT atmSysConfigCellTestPayload	1.3.6.1.4.1.164.12.3.1.1.33.7	OCTET STRING	read-write	The payload of the cell. For OAM cell the payload is set automatically to 6A.
I32 atmSysConfigCellTestQuantity	1.3.6.1.4.1.164.12.3.1.1.33.8	Integer32	read-write	Quantity of cells to send.
INT atmSysConfigCellTestSendCmd	1.3.6.1.4.1.164.12.3.1.1.33.9	INTEGER	read-write	Setting the variable to send(3) perfroms cell test. The agent will immediately reset the variable to off(2).
atmVpCrossConnectExtenTable	1.3.6.1.4.1.164.12.3.1.1.34		not-accessible	An extension to the ATM VP Cross Connect table (RFC2515 - atmVpCrossConnectTable).
atmVpCrossConnectExtenEntry	1.3.6.1.4.1.164.12.3.1.1.34.1		not-accessible	An entry in the table.
STR atmVpCrossConnectName	1.3.6.1.4.1.164.12.3.1.1.34.1.1	SnmpAdminString	read-create	The Connection's name.
atmVcCrossConnectExtenTable	1.3.6.1.4.1.164.12.3.1.1.35		not-accessible	An extension to the ATM VC Cross Connect table (RFC2515 - atmVcCrossConnectTable).
atmVcCrossConnectExtenEntry	1.3.6.1.4.1.164.12.3.1.1.35.1		not-accessible	An entry in the table.
STR atmVcCrossConnectName	1.3.6.1.4.1.164.12.3.1.1.35.1.1	SnmpAdminString	read-create	The Connection's name.
INT atmNteQosMode	1.3.6.1.4.1.164.12.3.1.1.37	INTEGER	read-write	This variable defines the QoS Mode. disable(1) - QoS is disabled. multipleVc(2) - QoS is enabled and multiple VCs can be bound per bridge port. singleVc(3) - QoS is enabled and only single VC can be bound per bridge port.
atmTrafficDescrParamXTable	1.3.6.1.4.1.164.12.3.1.1.38		not-accessible	An Augment to ATM Traffic Descriptor Parameter Table (atmTrafficDescrParamTable in ATM-MIB; RFC-2515).
atmTrafficDescrParamXEntry	1.3.6.1.4.1.164.12.3.1.1.38.1		not-accessible	An entry in the table.
INT atmTrafficDescrParamMode	1.3.6.1.4.1.164.12.3.1.1.38.1.1	INTEGER	read-create	The Mode of the Traffic Descriptor.
atmNteSysInfo	1.3.6.1.4.1.164.12.3.1.2
atmNteIdTable	1.3.6.1.4.1.164.12.3.1.2.1		not-accessible	The IDs of the cards and of the system.
atmNteIdEntry	1.3.6.1.4.1.164.12.3.1.2.1.1		not-accessible	.
I32 atmNteIdIndex	1.3.6.1.4.1.164.12.3.1.2.1.1.1	Integer32	read-only	An Index of the Unit ID table. The following units have IDs in this table: 1 - System 2 - ATM Board 3 - User Card 4 - Trunk 1 card 5 - Trunk 2 card 6 - Shaper 7 - Clock Unit 8 - Slot 1 card 9 - Slot 2 card 10 - Slot 3 card 11 - Slot 4 card 12 - Fan1 13 - Fan2 14 - Control Unit.
I32 atmNteUnitId	1.3.6.1.4.1.164.12.3.1.2.1.1.2	Integer32	read-only	The ID of the Unit. For index = 6, the id will describe the validity of a shaper in the system: 0 - Shaper Not exist 1 - Shaper exist. For index = 7, the id will describe the validity of a clock in the system: 0 - Clock Not exist 1 - Clock exist. 2- Clock exist but failed. For index = 12,13 the id will describe the functionality of a FAN1 : 0 - OK 1 - Failed.
STR atmNteUnitVersion	1.3.6.1.4.1.164.12.3.1.2.1.1.3	DisplayString	read-only	Hardware and Software version of the module.
INT atmNteCardType	1.3.6.1.4.1.164.12.3.1.2.1.1.4	INTEGER	read-only	The card type.
INT atmNteCardStatus	1.3.6.1.4.1.164.12.3.1.2.1.1.5	INTEGER	read-only	Status of the card in the selected slot. notActive - Connections are in NotReady state. No configuration is available for the card. The access to the card HW is blocked. This state is relevant for an extracted card, and for a case in which the card was deactivated. active - The module installed and functions. A card that in this state can be configured. inProgress - The status during proccessing of a command from atmNteCardCmd. empty - No information is valid for the selected slot. This status is relevant to a case in which the card configaration was deleted, or in case in which a slot was empty since the device startup.
INT atmNteCardCmd	1.3.6.1.4.1.164.12.3.1.2.1.1.6	INTEGER	read-write	Command on the card that is installed in the selected slot. The commands are applicable according to the value of atmNteCardStatus. See the specification document for details. deleteConfig - Deletes the card configuration. deactivate - All the connections state will be changed to NotReady. The card configuration will be blocked. activate - Does the same as done upon card insertion: Initiates the relevant parameters, activates the physical layer, ATM layer and logical layer.
INT atmNteProgCardType	1.3.6.1.4.1.164.12.3.1.2.1.1.7	INTEGER	read-write	The programmed card type.
I32 atmSysPSunits	1.3.6.1.4.1.164.12.3.1.2.2	Integer32	read-only	The number of power supply units.
INT atmSysPSunitsInUse	1.3.6.1.4.1.164.12.3.1.2.3	INTEGER	read-only	The main power supply in this unit.
I32 atmSysFanUnits	1.3.6.1.4.1.164.12.3.1.2.4	Integer32	read-only	The number of fan units.
I32 atmSysNetPrts	1.3.6.1.4.1.164.12.3.1.2.5	Integer32	read-only	The number of network ports.
INT atmSysNetPrtInUse	1.3.6.1.4.1.164.12.3.1.2.6	INTEGER	read-only	The network port in use.
INT atmNteBridgingMode	1.3.6.1.4.1.164.12.3.1.2.7	INTEGER	read-write	Bridging mode can be one of the following: ATM <> Ethernet - Bridging is between the Ethernet port and the ATM port (there is no bridging between VCs). ATM <> Ethernet + ATM - Bridging is done both between the Ethernet port and the ATM port and also between VCs.
atmSysStats	1.3.6.1.4.1.164.12.3.1.2.8
G32 atmSysCurrentCdc	1.3.6.1.4.1.164.12.3.1.2.8.1	Gauge32	read-only	Seconds in which cells dropped was occured in the current 15 minutes interval.
atmSysIntervalTable	1.3.6.1.4.1.164.12.3.1.2.8.2		not-accessible	The system level Interval table.
atmSysIntervalEntry	1.3.6.1.4.1.164.12.3.1.2.8.2.1		not-accessible	.
I32 atmSysIntervalNumber	1.3.6.1.4.1.164.12.3.1.2.8.2.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 atmSysIntervalCdc	1.3.6.1.4.1.164.12.3.1.2.8.2.1.2	Gauge32	read-only	Seconds in which cells dropped was occured in 15 minutes interval.
INT atmNteEventType	1.3.6.1.4.1.164.12.3.1.2.9	INTEGER	read-only	This parameter identifies the event. On - the problem exist. Off - the problem not exist. InvalidLogin - Invalid login on local console. CorrectLogin - Successful login operation.
I32 atmNteIntervalMaxNumber	1.3.6.1.4.1.164.12.3.1.2.10	Integer32	read-only	The MAX number of connections intervals supported by system. This parameter value is a function of atmNteConnectionsMaxNumber parameter. This parameter should affect the threshold values selected by user. Applicable to ace2002.
INT atmNteAlarmType	1.3.6.1.4.1.164.12.3.1.2.11	INTEGER	read-only	This object specifies the type of the alarm.
INT atmNteLevel	1.3.6.1.4.1.164.12.3.1.2.12	INTEGER	read-only	This object specifies the ATM level.
I32 atmNteConnectionsNumber	1.3.6.1.4.1.164.12.3.1.2.13	Integer32	read-only	This object specifies a quantity of connections.
I32 atmNteTotalLb	1.3.6.1.4.1.164.12.3.1.2.14	Integer32	read-only	This parameter counts the total number of end-points that were configured with Loopback (LB).
I32 atmNteTotalCc	1.3.6.1.4.1.164.12.3.1.2.15	Integer32	read-only	This parameter counts the total number of end-points that were configured with Continuity Check (CC).
I32 atmNteTotalPm	1.3.6.1.4.1.164.12.3.1.2.16	Integer32	read-only	This parameter counts the total number of end-points that were configured with PM.
atmNtePrt	1.3.6.1.4.1.164.12.3.2
atmNtePrtConfig	1.3.6.1.4.1.164.12.3.2.1
atmNteConfIfTable	1.3.6.1.4.1.164.12.3.2.1.1		not-accessible	The Physical interface configuration table.
atmNteConfIfEntry	1.3.6.1.4.1.164.12.3.2.1.1.1		not-accessible	An entry in the Physical interface configuration table. The ifIndex is of the lowest physical layer.
INT atmConfIfTransmitClk	1.3.6.1.4.1.164.12.3.2.1.1.1.1	INTEGER	read-write	The transmit clock of the port.
INT atmConfIfLoopback	1.3.6.1.4.1.164.12.3.2.1.1.1.2	INTEGER	read-write	Interface Loopback.
INT atmConfIfFrameType	1.3.6.1.4.1.164.12.3.2.1.1.1.3	INTEGER	read-write	The frame type. Valid values for a 155M interface: sonet(2), sdh(3). Valid values for a T3 interface: direct(4), plcpInternal(5), plcpExternal(6), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbling(12). Valid values for Ethernet interface: ethCrcTrans (8), ethCrcNotTrans(9). (DS1 interfaces frame type is specified in the DSX1 mib).
INT atmConfIfCardType	1.3.6.1.4.1.164.12.3.2.1.1.1.4	INTEGER	read-only	The card type.
INT atmConfAtmIfVpiVciLimit	1.3.6.1.4.1.164.12.3.2.1.1.1.5	INTEGER	read-only	The limit on the sum of the VPI+VCI bits for this interface.
INT atmConfIfHwFeatures	1.3.6.1.4.1.164.12.3.2.1.1.1.6	INTEGER	read-write	HW features command.
I32 atmConfIfOutputRate	1.3.6.1.4.1.164.12.3.2.1.1.1.7	Integer32	read-write	This parameter indicates the output rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.
I32 atmConfIfInputRate	1.3.6.1.4.1.164.12.3.2.1.1.1.8	Integer32	read-write	This parameter indicates the input rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.
INT atmConfAlarmForwarding	1.3.6.1.4.1.164.12.3.2.1.1.1.9	INTEGER	read-write	Enables Path AIS Alarm forwarding upon a failure detection. The following might be considered as a failure: LOS, LOF, LOC, SLM, LOP, Path AIS and Line AIS. disable(2) - will not forward an alarm upon a failure on this port. enable(3) - will forward an alarm upon a failure on this port.
I32 atmConfIfAllocatedBw	1.3.6.1.4.1.164.12.3.2.1.1.1.10	Integer32	read-only	Total VC Bandwidth Allocation.
I32 atmConfIfLowerVpi	1.3.6.1.4.1.164.12.3.2.1.1.1.11	Integer32	read-write	The Lower possible VPI.
INT atmConfIfOamMode	1.3.6.1.4.1.164.12.3.2.1.1.1.12	INTEGER	read-write	OAM support Mode, which determines the interface's location in a segment wise.
INT atmConfIfOamFailureInd	1.3.6.1.4.1.164.12.3.2.1.1.1.13	INTEGER	read-write	This object allows user to define the type of indication (if any) that will be created upon a LB cell failure, for all VCs on which OAM loopback traffic is activated. disabled(2) - no indication will be created. ais(3) - will cause Tx of AIS. rdi(4) - will cause Tx of RDI. aisAndRdi(5) - will cause Tx of AIS & RDI. For LA-110, indication will be sent only for VCs with atmConfVcLoopbackFailureInd <> disabled
atmNteAlarmIfTable	1.3.6.1.4.1.164.12.3.2.1.2		not-accessible	The interface Alarm table.
atmNteAlarmIfEntry	1.3.6.1.4.1.164.12.3.2.1.2.1		not-accessible	An entry in the interface Alarm table.
I32 atmInterfaceActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.2.1.1	Integer32	read-only	A Bit String of the active alarms on this interface. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - LOS 2 - LOF 3 - Line AIS (SONET)/ PLCP LOF (DS3) 4 - LOP 5 - Path AIS 6 - SLM 7 - LCD 8 - Line RDI (SONET)/ PLCP Yellow (DS3) 9 - Path RDI (SONET)/ RDI (DS3) 10 - Section BIP (SONET)/ P1/P2 (DS3) > Threshold 11 - Line BIP (SONET)/ PLCP BIP (DS3) > Threshold 12 - Line FEBE (SONET)/ PLCP FEBE (DS3) > Threshold 13 - Path BIP > Threshold 14 - Path FEBE > Threshold 15 - HW Failure
I32 atmThresholdSectionBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.2	Integer32	read-write	When Section BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
I32 atmThresholdLineBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.3	Integer32	read-write	When Line BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
I32 atmThresholdLineFEBE	1.3.6.1.4.1.164.12.3.2.1.2.1.4	Integer32	read-write	When Line FEBEs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
I32 atmThresholdPathBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.5	Integer32	read-write	When Path BIPs are greater than this threshold, an active alarm is raised.
I32 atmThresholdPathFEBE	1.3.6.1.4.1.164.12.3.2.1.2.1.6	Integer32	read-write	When Path FEBEs are greater than this threshold, an active alarm is raised.
I32 atmThresholdErroredCells	1.3.6.1.4.1.164.12.3.2.1.2.1.7	Integer32	read-write	When Errored Cells are greater than this threshold, an active alarm is raised.
I32 atmThresholdLostCells	1.3.6.1.4.1.164.12.3.2.1.2.1.8	Integer32	read-write	When Lost Cells are greater than this threshold, an active alarm is raised.
I32 atmThresholdMisinsertedCells	1.3.6.1.4.1.164.12.3.2.1.2.1.9	Integer32	read-write	When Misinserted Cells are greater than this threshold, an active alarm is raised.
INT atmInterfaceAlarmStatus	1.3.6.1.4.1.164.12.3.2.1.2.1.10	INTEGER	read-only	The variable is on(3) when there is any active alarm on this interface.
I32 atmInterfaceMaskAlarms	1.3.6.1.4.1.164.12.3.2.1.2.1.11	Integer32	read-write	A Bit String of alarms mask on this interface. An up bit (1) means that the respective alarm is masked. A down bit (0) means no mask. The mask is supported for the following alarms: 1 - LOS
atmNteConfVpTable	1.3.6.1.4.1.164.12.3.2.1.3		not-accessible	The ATM VP configuration table. The table is an extension to the atmVplTable of RFC-1695.
atmNteConfVpEntry	1.3.6.1.4.1.164.12.3.2.1.3.1		not-accessible	An entry in the ATM VP configuration table. ifIndex of the ATM layer.
INT atmConfVpPolicing	1.3.6.1.4.1.164.12.3.2.1.3.1.1	INTEGER	read-write	Policing method desired for this VPL.
INT atmConfVpCCAdminStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.2	INTEGER	read-write	up(2) - Activate Continuity Check (CC). down(3) - Deactivate CC. source(4) - Activate OAM CC(Continuity Check) of local agent ( start sending Oam cells to the remote side ). sink(5) - Activate CC of remote agent ( start receiving Oam cells from remote side ). listenToActivationCells (6) - Passive listener till gets an activation request originateActivationCells(7) - Sands Activation cell according to atmConfVcCCDirection.
INT atmConfVpLoopbackAdminStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.3	INTEGER	read-write	up(2) - Start loopback OAM cells. down(3) - Stop sending loopback OAM cells. For ace2002: up(2) - Transmitting LB cells with llid all ones (i.e. FFFF..FF) down(3) - Not transmitting LB cells. llid(4) - Transmitting LB cells with llid indicated in the address field. segment(5) - Transmitting Segment LB cells with llid all ones. endToEnd(6) - Transmitting End to End LB cells with llid all ones. segmentLlid(7) - Transmitting Segment LB cells with llid indicated in the address field. endToEndLlid(8) - Transmitting LB cells with llid indicated in the address field. This parameter value might be in conflict with atmConfVpOamSupport value, since this parameter is for LB, while atmConfVpOamSupport is for any other OAM cells.
OCT atmConfVpLoopbackSinkAddress	1.3.6.1.4.1.164.12.3.2.1.3.1.4	OCTET STRING	read-write	Destination address. For ace101: 2 bytes are used. For ace2002: 16 bytes are used.
OCT atmConfVpCongestionControl	1.3.6.1.4.1.164.12.3.2.1.3.1.5	OCTET STRING	read-write	Each bit indicates a selection of one option as the following description. All combinations are possible and legal. The codes are: 1 - EPD 2 - CLP 4 - EFCI
INT atmConfVpCCDirection	1.3.6.1.4.1.164.12.3.2.1.3.1.6	INTEGER	read-write	both(2) - Agent send OAM CC cells and check received OAM CC cells source(4)- Agent send OAM CC cells. sink(5) - Agent checks received OAM CC cells.
DAT atmConfVpCreationTime	1.3.6.1.4.1.164.12.3.2.1.3.1.7	DateAndTime	read-only	A date-time in which the VP was created.
INT atmConfVpOamSupport	1.3.6.1.4.1.164.12.3.2.1.3.1.8	INTEGER	read-write	OAM support mode, which determines the device location in a segment wise.
INT atmConfVpCCOperStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.9	INTEGER	read-only	initial(1) - The CC activation process is not started. source(4) - Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells. both (8) - OAM CC of local and remote agents activation. timeout (9) - Timeout occured on receiving answer from the remote agent. denied (10) - CC activation process rejected by remote agent. conflict (11) - local and remote sides requested activation simultaneously. manual (12) - OAM CC of local agent activated manually.
INT atmConfVpLoopbackTraffic	1.3.6.1.4.1.164.12.3.2.1.3.1.10	INTEGER	read-write	This parameter has both command and status meanings: off(2) - Set to 'Off' will Stop traffic loop. Getting this value means that the loop is not running. on (3) - Set to 'On' will start traffic loop. Getting this value means that the loop is currently running.
INT atmConfVpLoopbackFailureInd	1.3.6.1.4.1.164.12.3.2.1.3.1.11	INTEGER	read-write	This object allows user to define the Indication that will be created upon a LB cell failure. disabled(2) - no indication will be created. segmentAis(3) - will cause Tx of a segment AIS. segmentRdi(4) - will cause Tx of a segment RDI. segmentAisAndRdi(5) - will cause Tx of a segment AIS & RDI. endToEndAis(6) - will cause Tx of an End to End AIS. endToEndRdi(7) - will cause Tx of an End to End RDI. endToEndAisAndRdi(8) - will cause Tx of an End to End AIS & RDI. Default: disabled(2).
I32 atmConfVpLoopbackFailureThreshold	1.3.6.1.4.1.164.12.3.2.1.3.1.12	Integer32	read-write	The number of the LB failures before starting transmission of the Indication defined by atmConfVcLoopbackFailureInd. Range: 1..16. Default: 1.
INT atmConfVpOamDirection	1.3.6.1.4.1.164.12.3.2.1.3.1.13	INTEGER	read-write	The direction of OAM cell insertion. downStream(2) - The OAM cell will be inserted in downStream. upStream(3) - The OAM cell will be inserted in upStream.
I32 atmConfVpOamDescrIndex	1.3.6.1.4.1.164.12.3.2.1.3.1.14	Integer32	read-write	This parameter indicates the VPL's OAM Descriptor index, according to the OAM Descriptor Configuration Table.
INT atmConfVpConnected	1.3.6.1.4.1.164.12.3.2.1.3.1.15	INTEGER	read-write	This object indicates whether this VP is connected and if connected, what is it connected to.
atmNteAlarmVpTable	1.3.6.1.4.1.164.12.3.2.1.5		not-accessible	The ATM VP Alarm table.
atmNteAlarmVpEntry	1.3.6.1.4.1.164.12.3.2.1.5.1		not-accessible	An entry in the ATM VP Alarm table. ifIndex of the ATM layer.
I32 atmNteVpAlarmVpi	1.3.6.1.4.1.164.12.3.2.1.5.1.1	Integer32	read-only	The VPI on which there is an active alarm.
I32 atmNteVpActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.5.1.2	Integer32	read-only	A Bit String of the active alarms on this VP. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VP AIS 2 - VP Loss Of Continuity 3 - VP RDI Reception 4 - VP Errored Cells > Threshold 5 - VP Lost Cells > Threshold 6 - VP Misinserted Cells > Threshold 9 - VP Loopback Failure
atmNteAlarmVcTable	1.3.6.1.4.1.164.12.3.2.1.6		not-accessible	The ATM VC Alarm table.
atmNteAlarmVcEntry	1.3.6.1.4.1.164.12.3.2.1.6.1		not-accessible	An entry in the ATM VC Alarm table. ifIndex of the ATM layer.
I32 atmNteVcAlarmVpi	1.3.6.1.4.1.164.12.3.2.1.6.1.1	Integer32	read-only	The VPI of the VC on which there is an active alarm.
I32 atmNteVcAlarmVci	1.3.6.1.4.1.164.12.3.2.1.6.1.2	Integer32	read-only	The VCI of the VC on which there is an active alarm.
I32 atmNteVcActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.6.1.3	Integer32	read-only	A Bit String of the active alarms on this VC. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VC AIS 2 - VC Loss Of Continuity 3 - VC RDI 4 - VC Errored Cells > Threshold 5 - VC Lost Cells > Threshold 6 - VC Misinserted Cells > Threshold 7 - Tx VC AIS 8 - Tx VC RDI 9 - VC Loopback Failure
atmNteLoopback	1.3.6.1.4.1.164.12.3.2.2
atmLoopbackVpTable	1.3.6.1.4.1.164.12.3.2.2.1		not-accessible	This table contains parameters for an OAM VP loopback test.
atmLoopbackVpEntry	1.3.6.1.4.1.164.12.3.2.2.1.1		not-accessible	An entry in table atmLoopbackVpTable.
I32 atmLoopbackVpIfIndex	1.3.6.1.4.1.164.12.3.2.2.1.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVpVpi	1.3.6.1.4.1.164.12.3.2.2.1.1.2	Integer32	read-only	The VPI of the OAM VPL.
INT atmLoopbackVpOperStatus	1.3.6.1.4.1.164.12.3.2.2.1.1.3	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.
I32 atmLoopbackVpCDV	1.3.6.1.4.1.164.12.3.2.2.1.1.4	Integer32	read-only	Cell Delay Variation for this sampling.
I32 atmLoopbackVpAverageDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.5	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVpMaxDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.6	Integer32	read-only	Maximum delay without including lost cells.
I32 atmLoopbackVpMinDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.7	Integer32	read-only	Minimum delay.
I32 atmLoopbackVpErrSessions	1.3.6.1.4.1.164.12.3.2.2.1.1.8	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
atmLoopbackVcTable	1.3.6.1.4.1.164.12.3.2.2.2		not-accessible	This table contains parameters for an OAM VC loopback test.
atmLoopbackVcEntry	1.3.6.1.4.1.164.12.3.2.2.2.1		not-accessible	An entry in table.
I32 atmLoopbackVcIfIndex	1.3.6.1.4.1.164.12.3.2.2.2.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVcVpi	1.3.6.1.4.1.164.12.3.2.2.2.1.2	Integer32	read-only	The VPI of the OAM VCL.
I32 atmLoopbackVcVci	1.3.6.1.4.1.164.12.3.2.2.2.1.3	Integer32	read-only	The VCI of the OAM VCL.
INT atmLoopbackVcOperStatus	1.3.6.1.4.1.164.12.3.2.2.2.1.4	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.
I32 atmLoopbackVcCDV	1.3.6.1.4.1.164.12.3.2.2.2.1.5	Integer32	read-only	Cell Delay Variation for this sampling.
I32 atmLoopbackVcAverageDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.6	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVcMaxDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.7	Integer32	read-only	The maximum delay without including lost cells.
I32 atmLoopbackVcMinDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.8	Integer32	read-only	The minimum delay.
I32 atmLoopbackVcErrSessions	1.3.6.1.4.1.164.12.3.2.2.2.1.9	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
atmLoopbackVpIvlTable	1.3.6.1.4.1.164.12.3.2.2.3		not-accessible	This table contains parameters for an OAM VP loopback test, according interval number.
atmLoopbackVpIvlEntry	1.3.6.1.4.1.164.12.3.2.2.3.1		not-accessible	An entry in table.
I32 atmLoopbackVpIvlIfIndex	1.3.6.1.4.1.164.12.3.2.2.3.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVpIvlVpi	1.3.6.1.4.1.164.12.3.2.2.3.1.2	Integer32	read-only	The VPI of the OAM VPL.
I32 atmLoopbackVpIvlIvl	1.3.6.1.4.1.164.12.3.2.2.3.1.3	Integer32	read-only	The relevant interval number.
INT atmLoopbackVpIvlOperStatus	1.3.6.1.4.1.164.12.3.2.2.3.1.4	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP during this interval. -inProgress(2) has no meaning for an ended interval. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was OK.
I32 atmLoopbackVpIvlCDV	1.3.6.1.4.1.164.12.3.2.2.3.1.5	Integer32	read-only	Cell Delay Variation for this interval.
I32 atmLoopbackVpIvlAverageDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.6	Integer32	read-only	Average delay without including lost cells for this interval.
I32 atmLoopbackVpIvlMaxDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.7	Integer32	read-only	The maximum delay without including lost cells for this interval.
I32 atmLoopbackVpIvlMinDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.8	Integer32	read-only	The minimum delay for this interval.
I32 atmLoopbackVpIvlErrSessions	1.3.6.1.4.1.164.12.3.2.2.3.1.9	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
atmLoopbackVcIvlTable	1.3.6.1.4.1.164.12.3.2.2.4		not-accessible	This table contains parameters for an OAM VC loopback test.
atmLoopbackVcIvlEntry	1.3.6.1.4.1.164.12.3.2.2.4.1		not-accessible	An entry in table.
I32 atmLoopbackVcIvlIfIndex	1.3.6.1.4.1.164.12.3.2.2.4.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVcIvlVpi	1.3.6.1.4.1.164.12.3.2.2.4.1.2	Integer32	read-only	The VPI of the OAM VCL.
I32 atmLoopbackVcIvlVci	1.3.6.1.4.1.164.12.3.2.2.4.1.3	Integer32	read-only	The VCI of the OAM VCL.
I32 atmLoopbackVcIvlIvl	1.3.6.1.4.1.164.12.3.2.2.4.1.4	Integer32	read-only	The relevant interval number.
INT atmLoopbackVcIvlOperStatus	1.3.6.1.4.1.164.12.3.2.2.4.1.5	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VC during this interval. -inProgress(2) has no meaning per interval. -failed(3) means there was problem for this test during this interval. -endSuccessfully(4) means that the test was OK.
I32 atmLoopbackVcIvlCDV	1.3.6.1.4.1.164.12.3.2.2.4.1.6	Integer32	read-only	Cell Delay Variation for this interval.
I32 atmLoopbackVcIvlAverageDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.7	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVcIvlMaxDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.8	Integer32	read-only	The maximum delay without including lost cells.
I32 atmLoopbackVcIvlMinDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.9	Integer32	read-only	The minimum delay.
I32 atmLoopbackVcIvlErrSessions	1.3.6.1.4.1.164.12.3.2.2.4.1.10	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
atmNtePM	1.3.6.1.4.1.164.12.3.2.3
atmVpPmTable	1.3.6.1.4.1.164.12.3.2.3.1		not-accessible	This table contains parameters for VP performance monitoring.
atmVpPmEntry	1.3.6.1.4.1.164.12.3.2.3.1.1		not-accessible	An entry in table.
I32 atmVpPmIfIndex	1.3.6.1.4.1.164.12.3.2.3.1.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmVpPmVpi	1.3.6.1.4.1.164.12.3.2.3.1.1.2	Integer32	read-only	The VPI of the Performance Monitoring VPL.
INT atmVpPmAdminStatus	1.3.6.1.4.1.164.12.3.2.3.1.1.3	INTEGER	read-create	up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .
INT atmVpPmDirection	1.3.6.1.4.1.164.12.3.2.3.1.1.4	INTEGER	read-create	The direction of PM.
I32 atmVpPmBlockSize	1.3.6.1.4.1.164.12.3.2.3.1.1.5	Integer32	read-create	Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.
ROW atmVpPmRowStatus	1.3.6.1.4.1.164.12.3.2.3.1.1.6	RowStatus	read-create	Creation/Deletion of rows in the table.
INT atmVpPmSink	1.3.6.1.4.1.164.12.3.2.3.1.1.7	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
INT atmVpPmSource	1.3.6.1.4.1.164.12.3.2.3.1.1.8	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
atmVcPmTable	1.3.6.1.4.1.164.12.3.2.3.2		not-accessible	This table contains parameters for VC performance monitoring.
atmVcPmEntry	1.3.6.1.4.1.164.12.3.2.3.2.1		not-accessible	An entry in table.
I32 atmVcPmIfIndex	1.3.6.1.4.1.164.12.3.2.3.2.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmVcPmVpi	1.3.6.1.4.1.164.12.3.2.3.2.1.2	Integer32	read-only	The VPI of the Performance Monitoring VCL.
I32 atmVcPmVci	1.3.6.1.4.1.164.12.3.2.3.2.1.3	Integer32	read-only	The VCI of the PM VCL.
INT atmVcPmAdminStatus	1.3.6.1.4.1.164.12.3.2.3.2.1.4	INTEGER	read-create	up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .
INT atmVcPmDirection	1.3.6.1.4.1.164.12.3.2.3.2.1.5	INTEGER	read-create	The direction of PM.
I32 atmVcPmBlockSize	1.3.6.1.4.1.164.12.3.2.3.2.1.6	Integer32	read-create	Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.
ROW atmVcPmRowStatus	1.3.6.1.4.1.164.12.3.2.3.2.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
INT atmVcPmSink	1.3.6.1.4.1.164.12.3.2.3.2.1.8	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
INT atmVcPmSource	1.3.6.1.4.1.164.12.3.2.3.2.1.9	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
atmNteMdl	1.3.6.1.4.1.164.12.3.3
atmNteMdlConfig	1.3.6.1.4.1.164.12.3.3.1
atmNteMdlConfigTable	1.3.6.1.4.1.164.12.3.3.1.1		not-accessible	Module configuration table.
atmNteMdlConfigEntry	1.3.6.1.4.1.164.12.3.3.1.1.1		not-accessible	There is an entry in this table just for those modules that have parameters that are relevant to module level only.
I32 atmNteMdlSlotIndex	1.3.6.1.4.1.164.12.3.3.1.1.1.1	Integer32	not-accessible	The slot number.
INT atmNteMdlPrtCpuSharing	1.3.6.1.4.1.164.12.3.3.1.1.1.2	INTEGER	read-write	This object lets the user decide what will be the CPU sharing between the ports of the module. This object is applicable for modules in which the same CPU handles the traffic of all ports. equal - All ports will have the same CPU resource. port1 - Port 1 will have higher priority than the other ports.
INT atmNteMdlInputPriorityMechanism	1.3.6.1.4.1.164.12.3.3.1.1.1.3	INTEGER	read-write	This object allows the user to Enable/Disable the Input priority mechanism. This object is applicable for modules with more than one port, in which the total ports input may be greater than the port output. disabled - all LAN VCCs will be transmitted through the same queue (queue 1). Upon congestion frames will be dropped randomly. enabled - the user should configure each port/connection priority. Upon congestion frames will be dropped according to priority.

Bits (6)
BIT alarmForwardingAction	1.3.6.1.4.1.164.6.2.50.1.11	Bits	read-create	Bit map representing the action to be performed when alarm forwarding will take place. bit 0 - No Action. '1' value - device should NOT perform any action, though other bits indicate the action to be taken. '0' value - device should perform the action/s indicated by rest of the bits. In this case, one of the other bits should be '1'. bit 1 - Interface Deactivation (of the affected Port: alarmForwardingToPort) bit 2 - OAM Signaling. Affected Port (alarmForwardingToPort) will send special OAM Signaling to the Far-End unit about the Failure. This object will be used only for devices that support Deactivation per entry OR can support more than one action.
BIT alarmForwardingCause	1.3.6.1.4.1.164.6.2.50.1.6	Bits	read-create	Bit map representing the cause upon which alarm forwarding will take place. bit 0 - LOSS (LINE DOWN) bit 1 - AIS bit 2 - RDI bit 3 - PROTOCOL DOWN.
BIT atmAlarmForwardingFailureLevel	1.3.6.1.4.1.164.12.3.1.1.32.1.4	Bits	read-create	This parameter determines the level of failure that will operate the Alarm Forwarding Mechanism.
BIT ethIfStormPacketType	1.3.6.1.4.1.164.3.1.6.1.5.1.1.4	Bits	not-accessible	Packet Type on which Storming operations will be performed.
BIT qosFlowMappingCriteria	1.3.6.1.4.1.164.6.3.9.2.1.5	Bits	read-create	This attribute determines upon which criterion the flow will be mapped.
BIT sysDclRedundancyStatus	1.3.6.1.4.1.164.3.3.1.2.2.1.1.10	Bits	read-only	Bit map representing current Redundancy Status. bit 0 - Indicates mismatch between the 2 CL cards' Configuration bit 1 - Indicates mismatch between the 2 CL cards' Software. bit 2 - Indicates CL card A Absence. bit 3 - Indicates CL card B Absence. bit 4 - Indicates Loss of Communication between the 2 CL cards. bit 5 - Indicates mismatch between the 2 CL cards' Hardware. bit 6 - Indicates Configuraton update is in process. bit 7 - Indicates Software update is in process.
BridgeId (1)
BRI radBridgeStpStatDesignatedRoot	1.3.6.1.4.1.164.4.1.11.2.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Counter32 (104)
C32 agnChangeCnt	1.3.6.1.4.1.164.6.2.4	Counter32	read-only	The number of changes in system configuration that were reported to the manager since last cold start
C32 atmIfRxCells	1.3.6.1.4.1.164.12.2.1.1.1.1.4	Counter32	read-only	The counter associated with the total number of received cells, encountered by an ATM interface.
C32 atmIfTxCells	1.3.6.1.4.1.164.12.2.1.1.1.1.3	Counter32	read-only	The counter associated with the total number of transmitted cells, encountered by an ATM interface.
C32 atmIfUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.1.1.5	Counter32	read-only	The counter associated with the total number of cells with uncorrected HEC errors, encountered by an ATM interface.
C32 atmVcShaperDiscarded	1.3.6.1.4.1.164.12.2.1.2.2.8.1.1	Counter32	read-only	The number of Cells that were discarded in the shaper on that VCC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.
C32 atmVcShaperEpdDropped	1.3.6.1.4.1.164.12.2.1.2.2.8.1.5	Counter32	read-only	The number of Cells that were dropped in the shaper on that VCC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VC only.
C32 atmVcShaperTotalEpdDropped	1.3.6.1.4.1.164.12.2.1.2.2.8.1.6	Counter32	read-only	The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VC only.
C32 atmVpShaperDiscarded	1.3.6.1.4.1.164.12.2.1.2.1.7.1.1	Counter32	read-only	The number of Cells that were discarded in the shaper on that VPC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.
C32 atmVpShaperEpdDropped	1.3.6.1.4.1.164.12.2.1.2.1.7.1.5	Counter32	read-only	The number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VP only.
C32 atmVpShaperTotalEpdDropped	1.3.6.1.4.1.164.12.2.1.2.1.7.1.6	Counter32	read-only	The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VP only.
C32 dsx1DataStreamStatInBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.5	Counter32	read-only	The counter associated with the number of received bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.6	Counter32	read-only	The counter associated with the number of Discarded incoming frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.7	Counter32	read-only	The counter associated with the number of received Errored frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.4	Counter32	read-only	The counter associated with the number of received frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.9	Counter32	read-only	The counter associated with the number of transmitted bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.10	Counter32	read-only	The counter associated with the number of Discarded outgoing frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.11	Counter32	read-only	The counter associated with the number of errored transmitted frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.8	Counter32	read-only	The counter associated with the number of transmitted frames, encountered by the DS1 Data Stream.
C32 ethOamServiceElapsedTime	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.14	Counter32	read-only	Indicates the time elapsed in seconds since the time the service is up.
C32 ethOamServiceFrameLoss	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.11	Counter32	read-only	Counts the number of frames lost since the time the service is up.
C32 ethOamServiceFramesAboveDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.17	Counter32	read-only	Indicates the number of frames arrived with delay greater than the delay threshold.
C32 ethOamServiceFramesAboveDelayVar	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.19	Counter32	read-only	Indicates the number of frames arrived with delay variation greater than the delay variation threshold.
C32 ethOamServiceOverflowFrameLoss	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.12	Counter32	read-only	The number of times the associated ethOamServiceFrameLoss counter has overflowed.
C32 ethOamServiceOverflowFramesAboveDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.18	Counter32	read-only	Indicates the number of times the associated ethOamServiceFramesAboveDelay counter has overflowed.
C32 ethOamServiceOverflowFramesAboveDelayVar	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.20	Counter32	read-only	Indicates the number of times the associated ethOamServiceFramesAboveDelayVar counter has overflowed.
C32 ethOamServiceOverflowTxFrames	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.10	Counter32	read-only	The number of times the associated ethOamServiceTxFrames counter has overflowed.
C32 ethOamServiceTxFrames	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.9	Counter32	read-only	Counts the number of frames trnasmitted by since the time the service is up.
C32 ethOamServiceUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.15	Counter32	read-only	Indicates the number of unavailable seconds since the time the service is up.
C32 ip2IfCurrentStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.10.1.3	Counter32	read-only	Number of seconds that the buffer overflows in the current interval. This records the count of the number of seonds the Receive (Eth to TDM) buffer overflows in the current interval.
C32 ip2IfCurrentStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.10.1.2	Counter32	read-only	Number of seconds that the buffer underflows in the current interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflows in the current interval. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
C32 ip2IfCurrentStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.10.1.1	Counter32	read-only	Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the current interval.
C32 ip2IfCurrentStatTxErrFrameSec	1.3.6.1.4.1.164.3.1.6.7.10.1.7	Counter32	read-only	The number of seconds in which errored frames were transmitted during the current interval. The error may be one of the following: CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.
C32 ip2IfIntervalStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.11.1.4	Counter32	read-only	Number of seconds that the buffer overflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer overflows in the selected interval.
C32 ip2IfIntervalStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.11.1.3	Counter32	read-only	Number of seconds that the buffer underflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflows in the selected interval. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
C32 ip2IfIntervalStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.11.1.2	Counter32	read-only	Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the selected interval.
C32 ip2IfIntervalStatTxErrFrameSec	1.3.6.1.4.1.164.3.1.6.7.11.1.8	Counter32	read-only	The number of seconds in which errored frames were transmitted during the selected interval. The error may be one of the following: CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.
C32 ip2IfStatFrameTrackDupDrop	1.3.6.1.4.1.164.3.1.6.7.7.1.25	Counter32	read-only	The number of packets dropped due to being duplicated. (duplicated packet means a packet that has the same sequential number as a packet being received previously).
C32 ip2IfStatFrameTrackMissing	1.3.6.1.4.1.164.3.1.6.7.7.1.26	Counter32	read-only	The number of packets that are missing. (Missing packet means an expected packet- according to the current sequential number - that was not received).
C32 ip2IfStatHdlcAbort	1.3.6.1.4.1.164.3.1.6.7.7.1.34	Counter32	read-only	This counter indicates the number of received HDLC frames with abort indication.
C32 ip2IfStatHdlcAlignErr	1.3.6.1.4.1.164.3.1.6.7.7.1.31	Counter32	read-only	This counter indicates the number of received HDLC frames with alignment errors.
C32 ip2IfStatHdlcCrcErr	1.3.6.1.4.1.164.3.1.6.7.7.1.30	Counter32	read-only	This counter indicates the number of received HDLC frames with CRC errors.
C32 ip2IfStatHdlcErroredFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.36	Counter32	read-only	Number of received errored HDLC frames.
C32 ip2IfStatHdlcOversize	1.3.6.1.4.1.164.3.1.6.7.7.1.32	Counter32	read-only	This counter indicates the number of received HDLC frames longer than 1470.
C32 ip2IfStatHdlcUndersize	1.3.6.1.4.1.164.3.1.6.7.7.1.33	Counter32	read-only	This counter indicates the number of received HDLC frames shorter than 4.
C32 ip2IfStatPsnReorderFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.21	Counter32	read-only	Number of times that Frames had been reordered in PSN.
C32 ip2IfStatPsnRxFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.16	Counter32	read-only	Number of frames that were recieved from PSN.
C32 ip2IfStatPsnSeqErrors	1.3.6.1.4.1.164.3.1.6.7.7.1.20	Counter32	read-only	Number of times that the sequence number of an incoming Frame indicates Loss of Frame or Out of order occured in PSN.
C32 ip2IfStatPsnTxFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.15	Counter32	read-only	Number of frames that were transmitted to PSN.
C32 ip2IfStatRdnFlip	1.3.6.1.4.1.164.3.1.6.7.7.1.13	Counter32	read-only	Number of redundancy flips occured. This parameter counts only flips from this bundle to the other bundle in the redundancy couple.
C32 ip2IfStatRxCorrectFrames	1.3.6.1.4.1.164.3.1.6.7.7.1.35	Counter32	read-only	Number of received correct frames.
C32 ip2IfStatRxHdlc	1.3.6.1.4.1.164.3.1.6.7.7.1.9	Counter32	read-only	Number of HDLC frames that were received.
C32 ip2IfStatRxSignaling	1.3.6.1.4.1.164.3.1.6.7.7.1.7	Counter32	read-only	Number of signaling frames that were received.
C32 ip2IfStatRxVoice	1.3.6.1.4.1.164.3.1.6.7.7.1.8	Counter32	read-only	Number of voice frames that were received.
C32 ip2IfStatTxHdlc	1.3.6.1.4.1.164.3.1.6.7.7.1.12	Counter32	read-only	Number of HDLC frames that were transmitted.
C32 ip2IfStatTxOnMaxSize	1.3.6.1.4.1.164.3.1.6.7.7.1.6	Counter32	read-only	Number of frames that were transmitted due to reaching max. frame size. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing time interval elapses.
C32 ip2IfStatTxOnTimeInterval	1.3.6.1.4.1.164.3.1.6.7.7.1.5	Counter32	read-only	Number of frames that were transmitted due to time interval elapse. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing time interval elapses. The packetizing time interval is the interval in msec that it takes to build a Max. size frame.
C32 ip2IfStatTxSignaling	1.3.6.1.4.1.164.3.1.6.7.7.1.10	Counter32	read-only	Number of signaling frames that were transmitted.
C32 ip2IfStatTxVoice	1.3.6.1.4.1.164.3.1.6.7.7.1.11	Counter32	read-only	Number of voice frames that were transmitted.
C32 prtCrRxDataCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.7	Counter32	read-only	The number of Data Cells received by this port during the selected interval.
C32 prtCrRxTotalCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.5	Counter32	read-only	The total number of cells received by this port during the selected interval.
C32 prtCrTxDataCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.8	Counter32	read-only	The number of Data Cells sent by this port during the selected interval.
C32 prtCrTxTotalCells	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.6	Counter32	read-only	The total number of cells sent by this port during the selected interval.
C32 prtDlciRxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.14	Counter32	read-only	Number of data frames received by this DLCI, exceeding the Burst Committed value.
C32 prtDlciRxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.12	Counter32	read-only	Number of data frames received by this DLCI, exceeding the Burst Excess value.
C32 prtDlciRxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.8	Counter32	read-only	All the frames discarded due to congestion, received by this DLCI.
C32 prtDlciRxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.6	Counter32	read-only	The number of De frames discarded due to congestion, received by this DLCI.
C32 prtDlciRxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.4	Counter32	read-only	The number of De frames received by this DLCI.
C32 prtDlciTxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.15	Counter32	read-only	Number of data frames sent by this DLCI, exceeding the Burst Committed value.
C32 prtDlciTxBecn	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.11	Counter32	read-only	Number of frames sent by this DLCI, indicating backward congestion.
C32 prtDlciTxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.13	Counter32	read-only	Number of data frames sent by this DLCI, exceeding the Burst Excess value.
C32 prtDlciTxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.9	Counter32	read-only	All the frames discarded due to congestion, sent by this DLCI.
C32 prtDlciTxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.7	Counter32	read-only	The number of De frames discarded due to congestion, sent by this DLCI.
C32 prtDlciTxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.5	Counter32	read-only	The number of De frames sent by this DLCI.
C32 prtDlciTxFecn	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.10	Counter32	read-only	Number of frames sent by this DLCI, indicating forward congestion.
C32 prtFrRxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.23	Counter32	read-only	Number of data frames received by this port during the selected interval, exceeding the Burst Committed value.
C32 prtFrRxBecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.19	Counter32	read-only	Number of frames received by this port during the selected interval, indicating backward congestion.
C32 prtFrRxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.21	Counter32	read-only	Number of data frames received by this port during the selected interval, exceeding the Burst Excess value.
C32 prtFrRxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.15	Counter32	read-only	All the frames discarded due to congestion, received by this port during the selected interval.
C32 prtFrRxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.13	Counter32	read-only	The number of De frames discarded due to congestion, received by this port during the selected interval.
C32 prtFrRxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.11	Counter32	read-only	The number of De frames received by this port during the selected interval.
C32 prtFrRxFecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.17	Counter32	read-only	Number of frames received by this port during the selected interval, indicating forward congestion.
C32 prtFrRxMngFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.9	Counter32	read-only	The management number of frames received by this port during the selected interval.
C32 prtFrRxTotalBytes	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.7	Counter32	read-only	The total number of bytes received by this port during the selected interval.
C32 prtFrRxTotalFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.5	Counter32	read-only	The total number of frames received by this port during the selected interval.
C32 prtFrTxBcViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.24	Counter32	read-only	Number of data frames sent by this port during the selected interval, exceeding the Burst Committed value.
C32 prtFrTxBecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.20	Counter32	read-only	Number of frames sent by this port during the selected interval, indicating backward congestion.
C32 prtFrTxBeViol	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.22	Counter32	read-only	Number of data frames sent by this port during the selected interval, exceeding the Burst Excess value.
C32 prtFrTxDcrdCongAllFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.16	Counter32	read-only	All the frames discarded due to congestion, sent by this port during the selected interval.
C32 prtFrTxDcrdCongDeFr	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.14	Counter32	read-only	The number of De frames discarded due to congestion, sent by this port during the selected interval.
C32 prtFrTxDeFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.12	Counter32	read-only	The number of De frames sent by this port during the selected interval.
C32 prtFrTxFecn	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.18	Counter32	read-only	Number of frames sent by this port during the selected interval, indicating forward congestion.
C32 prtFrTxMngFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.10	Counter32	read-only	The management number of frames sent by this port during the selected interval.
C32 prtFrTxTotalBytes	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.8	Counter32	read-only	The total number of bytes sent by this port during the selected interval.
C32 prtFrTxTotalFrames	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.6	Counter32	read-only	The total number of frames sent by this port during the selected interval.
C32 radBridgeCODNumAccess	1.3.6.1.4.1.164.4.1.4.1.1.7	Counter32	read-only	The number of successful connections that have been established since the COD has been reset.
C32 radBridgeIPXRipInDiscards	1.3.6.1.4.1.164.4.1.5.2.3	Counter32	read-only	The number of received packets discarded by RIP.
C32 radBridgeIPXRipInPackets	1.3.6.1.4.1.164.4.1.5.2.2	Counter32	read-only	The total number of packets received by RIP. This will include any packets that are subsequently discarded.
C32 radBridgeIPXRipOutPackets	1.3.6.1.4.1.164.4.1.5.2.1	Counter32	read-only	The total number of packets transmitted by RIP.
C32 radBridgeIPXSapInDiscards	1.3.6.1.4.1.164.4.1.5.3.3	Counter32	read-only	The number of received packets discarded by SAP.
C32 radBridgeIPXSapInPackets	1.3.6.1.4.1.164.4.1.5.3.2	Counter32	read-only	The total number of packets received by SAP. This will include any packets that are subsequently discarded.
C32 radBridgeIPXSapOutPackets	1.3.6.1.4.1.164.4.1.5.3.1	Counter32	read-only	The total number of packets transmitted by SAP.
C32 radMepLbmOut	1.3.6.1.4.1.164.3.1.6.1.3.1.1.28	Counter32	read-only	Total number of Loopback Messages transmitted.
C32 radMepLbrIn	1.3.6.1.4.1.164.3.1.6.1.3.1.1.26	Counter32	read-only	Total number of valid, in-order Loopback Replies received.
C32 radMepLbrInOutOfOrder	1.3.6.1.4.1.164.3.1.6.1.3.1.1.27	Counter32	read-only	The total number of valid, out-of-order Loopback Replies received.
Counter64 (1)
C64 ifPerfHCCounter	1.3.6.1.4.1.164.6.2.35.2.1.1.4	Counter64	read-only	This High Capacity counter holds whole 64 bits of the counter indicated by ifPerfCounterType (concatenates both counter parts ifPerfHighCounterPart&ifPerfLowCounterPart) This object can be supported only by agents using SNMPv2 or SNMPv3.
DateAndTime (1)
DAT atmConfVpCreationTime	1.3.6.1.4.1.164.12.3.2.1.3.1.7	DateAndTime	read-only	A date-time in which the VP was created.
DisplayString (94)
STR agnCFlipLogicalExp	1.3.6.1.4.1.164.3.1.2.5.3.1.4	DisplayString	read-write	A logical expression composed of events numbers (which were configured in the 'AgnCFlipNetEvantsTable') and logical operators ('\|', '&', '!', '(', ')') between them. e.g - (1 & !2) \| (121 & 230)
STR agnCFlipNetEventEndTime	1.3.6.1.4.1.164.3.1.2.5.2.1.12	DisplayString	read-write	The time event will be deactivated at this time. The format is hh:mm.
STR agnCFlipNetEventStartTime	1.3.6.1.4.1.164.3.1.2.5.2.1.11	DisplayString	read-write	The time event will be activated at this time. The format is hh:mm.
STR agnCnfgDesc	1.3.6.1.4.1.164.3.1.2.2.7.1.2	DisplayString	read-write	This object is a description of the Configuration, entered by user, to enhance Cnfg recognition.
STR agnCnfgUpdDate	1.3.6.1.4.1.164.3.1.2.2.7.1.3	DisplayString	read-only	This object indicates the date when last update of this configuration was performed, as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. When update is performed, the agent should save the date.
STR agnCnfgUpdTime	1.3.6.1.4.1.164.3.1.2.2.7.1.4	DisplayString	read-only	This object indicates the time when last update of this configuration was performed, as it is known by the agent using its own real-time clock. When update is performed, the agent should save the time.
STR agnHwVersion	1.3.6.1.4.1.164.6.2.1	DisplayString	read-write	ASCII string for description and display of the agent hardware version, as it is known by the agent software.The user can update the version upon request when he changes components in the agent's module
STR agnListDecodingDescription	1.3.6.1.4.1.164.3.1.2.7.1.1.3	DisplayString	read-only	The description fitting the specific code and type of list required.
STR agnSAlrCodeDescription	1.3.6.1.4.1.164.3.1.2.1.15.1.2	DisplayString	read-only	This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
STR agnSDateCmd	1.3.6.1.4.1.164.3.1.2.1.2	DisplayString	read-write	This entry indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent.
STR agnSErrDescription	1.3.6.1.4.1.164.3.1.2.1.20.1.2	DisplayString	read-only	This attribute is a full text description of the sanity check error including error code, slot and port numbers related to the code .
STR agnSigProfName	1.3.6.1.4.1.164.3.1.2.10.2.1.3	DisplayString	read-write	Profile Name given by user.
STR agnSLastCnfgFlipCause	1.3.6.1.4.1.164.3.1.2.1.7	DisplayString	read-only	This entry describes the flip's cause.
STR agnSLastCnfgFlipTime	1.3.6.1.4.1.164.3.1.2.1.6	DisplayString	read-only	This entry indicates the Date & Time of the last flip to the current configuration at the agent.
STR agnSTimeCmd	1.3.6.1.4.1.164.3.1.2.1.3	DisplayString	read-write	This entry indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent.
STR agnVoiceSwConfNodeId	1.3.6.1.4.1.164.3.1.2.9.1.1.3	DisplayString	read-write	1, 2 or 3 digits, (1-9),(0-9),(0-9).
STR agnVoiceSwConfRtData	1.3.6.1.4.1.164.3.1.2.9.2.1.5	DisplayString	read-create	This field is relevant for actions hgr(6), and rep(8), numDigDP(11) and contains the following information: For hgr - the number of the Hunt Group. For rep - the number of digits to be replaced with. For numDigDP - the number of digits collected before establishing the call. 0 indicates no defined length. In this case SIDT will be used.
STR agnVoiceSwConfRtDigits	1.3.6.1.4.1.164.3.1.2.9.2.1.3	DisplayString	read-create	Dialed digits: Series of digits 0...9, '', '#' or '%'. The '' and '#' can have many uses according to the user's decision. For example, they can be used as part of the Dialed Number, they exist on the phone number panel. '*' can also be used instead of a series of numbers. The '%' means any digits (wildcard) and is used without a series of digits. When the agnVoiceSwConfRtAction is del (7), the series of digits that are configured via this MIB object will be deleted from the prefix of the dialed number.
STR agnVoiceSwConfZoneId	1.3.6.1.4.1.164.3.1.2.9.1.1.2	DisplayString	read-write	1 or 2 digits, (0-9)(1-9).
STR alrBufDescription	1.3.6.1.4.1.164.3.1.2.4.1.1.2	DisplayString	read-only	This entry is a unique text description of the alarm in the buffer. The alarm description includes the following information: alarm code, slot id, card type, channel id , alarm text, alarm status, masked flag and event counter
STR alrGenDescription	1.3.6.1.4.1.164.3.3.4.3.1.2	DisplayString	read-only	This entry is a unique text description, of the alarm corresponding to the specified code.
STR atmGenSysLogMessage	1.3.6.1.4.1.164.12.2.2.1.3.1.2	DisplayString	read-only	The log buffer entry message text.
STR atmGenSysSelfTestModule	1.3.6.1.4.1.164.12.2.2.1.1.1.3	DisplayString	read-only	The name of module on which the test was performed.
STR atmGenSysSelfTestResult	1.3.6.1.4.1.164.12.2.2.1.1.1.2	DisplayString	read-only	The results of the initial testing of the device.
STR atmIntervalDateDate	1.3.6.1.4.1.164.12.2.1.3.1.2	DisplayString	read-only	The date corresponding to this interval.
STR atmIntervalDateTime	1.3.6.1.4.1.164.12.2.1.3.1.3	DisplayString	read-only	The time corresponding to this interval.
STR atmNteUnitVersion	1.3.6.1.4.1.164.12.3.1.2.1.1.3	DisplayString	read-only	Hardware and Software version of the module.
STR chasVersion	1.3.6.1.4.1.164.3.1.1.1	DisplayString	read-only	An ASCII string for description and display of the agent chassis version.
STR dhcpClientStatus	1.3.6.1.4.1.164.11.7.2.2.1.6.1.4	DisplayString	read-only	This parametr displays the DHCP status.
STR fileName	1.3.6.1.4.1.164.6.2.12.2	DisplayString	read-write	The name of the file to be loaded. For protection, read returns NULL.
STR fileNameWithinProduct	1.3.6.1.4.1.164.6.2.12.9	DisplayString	read-write	The file name used by the product within the product file system.
STR intSwdlFileName	1.3.6.1.4.1.164.6.2.12.10.1.3	DisplayString	read-only	The name of the file.
STR intSwdlFileSwVer	1.3.6.1.4.1.164.6.2.12.10.1.4	DisplayString	read-only	The software version of the file.
STR intSwdlSize	1.3.6.1.4.1.164.6.2.12.10.1.6	DisplayString	read-only	The size of the file.
STR intSwdlSwDate	1.3.6.1.4.1.164.6.2.12.10.1.5	DisplayString	read-only	The software version date of the file.
STR mdlClLastFlipCause	1.3.6.1.4.1.164.3.3.2.2.1.1.5	DisplayString	read-only	The cause of last flip.
STR mdlClLastFlipDate	1.3.6.1.4.1.164.3.3.2.2.1.1.3	DisplayString	read-only	Date when last flip occured. The format would be as specified by the sysSDateFormat.
STR mdlClLastFlipTime	1.3.6.1.4.1.164.3.3.2.2.1.1.4	DisplayString	read-only	Time when last flip occured.
STR mdlSAlrCodeDescription	1.3.6.1.4.1.164.3.1.3.1.2.1.3	DisplayString	read-only	This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
STR mdlSBackupSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.16	DisplayString	read-only	This attribute indicates the Backup Software version of the card installed in the specific slot position.
STR mdlSHwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.3	DisplayString	read-only	This attribute indicates the Hardware version of the card installed in the specific slot position.
STR mdlSHwVersion	1.3.6.1.4.1.164.3.1.3.1.1.1.3	DisplayString	read-only	This attribute indicates the Hardware version of the installed card in the specific slot position.
STR mdlSSecondaryBackupSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.17	DisplayString	read-only	This attribute indicates the Secondary Backup Software version of the card installed in the specific slot position.
STR mdlSSwVer	1.3.6.1.4.1.164.3.3.2.1.1.1.4	DisplayString	read-only	This attribute indicates the Software version of the card installed in the specific slot position.
STR mdlSSwVersion	1.3.6.1.4.1.164.3.1.3.1.1.1.4	DisplayString	read-only	This attribute indicates the Software version of the installed card in the specific slot position.
STR modlParamSwVer	1.3.6.1.4.1.164.6.2.32.1.1.1.6	DisplayString	read-only	This attribute indicates the Module's Software Version.
STR prtAcmAlrString	1.3.6.1.4.1.164.3.2.3.2.20.1.1.6	DisplayString	read-write	Alarm string selected by user for the Inbound ports. This object is applicable only for the Inbound Ports: ext-5..ext-12. For the Outbound Ports (ext-1..ext-4), the size of this string will be 0.
STR prtBertResult	1.3.6.1.4.1.164.3.3.3.1.5.1.13	DisplayString	read-only	This object indicates Result of BERT for the selected port (number of error bits divided to the total number of data bits.) Applicable only if BERT is running on this port Agents that do not support this feature will send SIZE 0.
STR prtCfgParamInbandLoopActPattern	1.3.6.1.4.1.164.3.3.3.1.7.1.1.9	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtCfgParamInbandLoopPatternCfg=userConfig.
STR prtCfgParamInbandLoopDeactPattern	1.3.6.1.4.1.164.3.3.3.1.7.1.1.10	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtCfgParamInbandLoopPatternCfg=userConfig.
STR prtExPVc4DestinationNum	1.3.6.1.4.1.164.3.2.3.2.9.1.1.34	DisplayString	read-write	The destination phone number: 0 to 22 digits. Applicable for Auto Dial - ipForceConnect(6), Permanent Dial and Auto Accept Extension Types. Default: Null String
STR prtExPVc4ExtensionNumber	1.3.6.1.4.1.164.3.2.3.2.9.1.1.17	DisplayString	read-write	This is the extension number of this port. This field is relevant only when the extension type is voice switching and is read only if the port is member of a hunt group.
STR prtGenInterfaceType	1.3.6.1.4.1.164.3.3.3.1.1.1.12	DisplayString	read-only	This attribute indicates a unique HW interface type of the selected port. Examples: - for T1 cards: DSU, CSU - for E1 cards: DSU, LTU - for HS cards: v35, rs422, x21 etc...
STR prtHdslCompHwVer	1.3.6.1.4.1.164.3.3.3.7.1.1.7	DisplayString	read-only	This object indicates the Hardware Version of the component (Piggyback card) supporting this interface.
STR prtHdslCompSwVer	1.3.6.1.4.1.164.3.3.3.7.1.1.6	DisplayString	read-only	This object indicates the Software Version of the component (Piggyback card) supporting this interface.
STR prtHSInbandLoopActPattern	1.3.6.1.4.1.164.3.3.3.3.1.1.11	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig.
STR prtHSInbandLoopDeactPattern	1.3.6.1.4.1.164.3.3.3.3.1.1.12	DisplayString	read-write	This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig.
STR prtIsdnDirectoryLocalAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.4	DisplayString	read-create	This is the local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryLocalAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.11	DisplayString	read-create	This is the second local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryLocalSubAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.5	DisplayString	read-create	This is the local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
STR prtIsdnDirectoryLocalSubAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.12	DisplayString	read-create	This is the second local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
STR prtIsdnDirectoryRemoteAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.6	DisplayString	read-create	This is the remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
STR prtIsdnDirectoryRemoteAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.13	DisplayString	read-create	This is the second remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank(20 characters)
STR prtIsdnDirectoryRemoteSubAddr	1.3.6.1.4.1.164.3.2.3.2.16.3.1.7	DisplayString	read-create	This is the remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
STR prtIsdnDirectoryRemoteSubAddr2	1.3.6.1.4.1.164.3.2.3.2.16.3.1.14	DisplayString	read-create	This is the second remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
STR prtIsdnEndpointSpid	1.3.6.1.4.1.164.3.2.3.2.16.2.1.7	DisplayString	read-create	The Service profile IDentifier (SPID) information for this Terminal Endpoint. It is is composed of 9-20 numeric characters. It corresponds to isdnEndpointSpid in the isdn MIB.
STR prtIsdnStatusCalledNumber	1.3.6.1.4.1.164.3.2.3.1.16.1.4	DisplayString	read-only	This is the remote Number (ISDN Address) associated with this entry.
STR prtIsdnStatusCallingNumber	1.3.6.1.4.1.164.3.2.3.1.16.1.3	DisplayString	read-only	This is the local Number (ISDN Address) associated with this entry.
STR prtSAlrCodeDescription	1.3.6.1.4.1.164.3.1.4.1.2.1.4	DisplayString	read-only	This attribute is a full text description of the alarm. The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
STR prtSInterfaceType	1.3.6.1.4.1.164.3.1.4.1.1.1.14	DisplayString	read-only	This attribute indicates a unique HW interface type of the selected port.
STR prtSpAltNum	1.3.6.1.4.1.164.3.3.3.4.1.1.17	DisplayString	read-write	For DXC - this object is applicable only for port (2) = DP. It is the Alternate dialing number. This number is applicable only if prtSpAltNumMode is 'yes'.
STR prtSpPrimaryNum	1.3.6.1.4.1.164.3.3.3.4.1.1.16	DisplayString	read-write	For DXC - this object is applicable only for port (2) = DP. It is the Primary dialing number.
STR radBridgeCODTimeTriggerFrom	1.3.6.1.4.1.164.4.1.4.2.1.4	DisplayString	read-write	Time to start Dial Up connection, in format hh:mm.
STR radBridgeCODTimeTriggerTo	1.3.6.1.4.1.164.4.1.4.2.1.5	DisplayString	read-write	Time to terminate Dial Up connection, in format HH:MM.
STR radBridgeIPXSapName	1.3.6.1.4.1.164.4.1.5.3.6.1.2	DisplayString	read-only	The name of the server for which this entry pertains.
STR swdlStatusFileName	1.3.6.1.4.1.164.6.2.12.11.1.3	DisplayString	read-only	The name of the file.
STR swdlStatusSlot	1.3.6.1.4.1.164.6.2.12.11.1.4	DisplayString	read-only	The slot of the updated (or attempted to be updated) object.
STR swdlStatusSubSystem	1.3.6.1.4.1.164.6.2.12.11.1.5	DisplayString	read-only	The subsystem that updated (or attempted to be updated).
STR swdlStatusTime	1.3.6.1.4.1.164.6.2.12.11.1.7	DisplayString	read-only	This MIB parameter indicates the time SW download was finished. The format shuld be YYYY-MM-DD, hh:mm:ss
STR sysBufferAlrDate	1.3.6.1.4.1.164.3.3.1.5.1.1.6	DisplayString	read-only	The date when the alarm occured. The format will be according to sysSDateFormat.
STR sysBufferAlrTime	1.3.6.1.4.1.164.3.3.1.5.1.1.7	DisplayString	read-only	The time when the alarm occured.
STR sysDbaseFlipTime	1.3.6.1.4.1.164.3.3.1.7.4.1.2	DisplayString	read-write	This attribute indicates the time (HH:MM) when this data base will start being used by the Tmp config.
STR sysSaHwVersion	1.3.6.1.4.1.164.3.3.1.1.3	DisplayString	read-only	This object indicates the Hardware version of the system.
STR sysSaSwRevision	1.3.6.1.4.1.164.3.3.1.1.2	DisplayString	read-only	This object indicates the Software revision of the system.
STR sysSDateCmd	1.3.6.1.4.1.164.3.3.1.3.2	DisplayString	read-write	This object indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the sysSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent. * For KM-2100 V1 and FCD-T1/E1 - the string should contain '/' signs between day, month and year. Example: 12/08/1998. * For DXC and rest of the products - the string should contain '-' signs between day, month and year. Example: 12-08-1998. The day value will be in the range: 1..31. The month value will be in the range: 1..12. The year value will be in the range: 1996..2050 for products supporting the '-' format.
STR sysSErrDescription	1.3.6.1.4.1.164.3.3.1.3.13.1.3	DisplayString	read-only	This object is a full text description of the sanity check error including error code, IO slot and port numbers related to the code .
STR sysSRdnFlipCause	1.3.6.1.4.1.164.3.3.1.3.18.1.4	DisplayString	read-only	The last cause that caused the Flip from the Slot (Port) of sysSRdnSlot, sysSRdnPort.
STR sysSRdnFlipDate	1.3.6.1.4.1.164.3.3.1.3.18.1.5	DisplayString	read-only	Flip event Date. The format will be the one selected by user for sysSDateFormat.
STR sysSRdnFlipTime	1.3.6.1.4.1.164.3.3.1.3.18.1.6	DisplayString	read-only	Flip event Time. The format will be hh:mm:ss.
STR sysSTimeCmd	1.3.6.1.4.1.164.3.3.1.3.3	DisplayString	read-write	This object indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent. The string should contain ':' signs between hour, minute and second. Example: 11:05:58.
STR systemDate	1.3.6.1.4.1.164.6.2.14.1	DisplayString	read-write	System date.
STR systemTime	1.3.6.1.4.1.164.6.2.14.2	DisplayString	read-write	System time.
STR trapVal	1.3.6.1.4.1.164.6.2.11.1.2	DisplayString	read-only	This object is the actual ASCII description of the trap. It can be used also as attached variable of traps, in order to detail in explicit ASCII text, data of the trap. In this case, it is used as 'accessible-for-notify'.
STR xcDescr	1.3.6.1.4.1.164.6.2.31.1.7	DisplayString	read-create	A textual string containing information about the xc entry.
Dscp (1)
DSC dscpMappingDscpIdx	1.3.6.1.4.1.164.6.3.2.1.1.2	Dscp	not-accessible	DSCP value of the incoming IP packet
Gauge32 (359)
G32 agnClkCurrentBufferUnderflow	1.3.6.1.4.1.164.6.2.52.3.1.1.5	Gauge32	read-only	The counter associated with the number of times Underflow event encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkCurrentLostPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.3	Gauge32	read-only	The counter associated with the number of Lost Packets, encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkCurrentOutOfOrderPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.4	Gauge32	read-only	The counter associated with the number of times Out-of-Order Packets encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkCurrentRxPackets	1.3.6.1.4.1.164.6.2.52.3.1.1.2	Gauge32	read-only	The counter associated with the number of Received Packets, encountered by a Bridge Port in the current 15 minute interval.
G32 agnClkIntervalBufferUnderflow	1.3.6.1.4.1.164.6.2.52.3.2.1.6	Gauge32	read-only	The counter associated with the number of times Underflow event is detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 agnClkIntervalLostPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.4	Gauge32	read-only	The counter associated with the number of Lost Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 agnClkIntervalOutOfOrderPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.5	Gauge32	read-only	The counter associated with the number of times Out-of-Order Packets are detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 agnClkIntervalRxPackets	1.3.6.1.4.1.164.6.2.52.3.2.1.3	Gauge32	read-only	The counter associated with the number of Received Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 atmGenSysCxRefCounter	1.3.6.1.4.1.164.12.2.2.1.5.1.2	Gauge32	read-only	The counter counts the number of references that have been made to the object .
G32 atmIfCurrentCorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.2.1.3	Gauge32	read-only	The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentHecErrorSeconds	1.3.6.1.4.1.164.12.2.1.1.2.1.5	Gauge32	read-only	The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentRxCells	1.3.6.1.4.1.164.12.2.1.1.2.1.2	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentTxCells	1.3.6.1.4.1.164.12.2.1.1.2.1.1	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfCurrentUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.2.1.4	Gauge32	read-only	The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in the current 15 minute interval.
G32 atmIfIntervalCorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.3.1.4	Gauge32	read-only	The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalHecErrorSeconds	1.3.6.1.4.1.164.12.2.1.1.3.1.6	Gauge32	read-only	The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalRxCells	1.3.6.1.4.1.164.12.2.1.1.3.1.3	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalTxCells	1.3.6.1.4.1.164.12.2.1.1.3.1.2	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmIfIntervalUncorrectedHecs	1.3.6.1.4.1.164.12.2.1.1.3.1.5	Gauge32	read-only	The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
G32 atmSysCurrentCdc	1.3.6.1.4.1.164.12.3.1.2.8.1	Gauge32	read-only	Seconds in which cells dropped was occured in the current 15 minutes interval.
G32 atmSysIntervalCdc	1.3.6.1.4.1.164.12.3.1.2.8.2.1.2	Gauge32	read-only	Seconds in which cells dropped was occured in 15 minutes interval.
G32 atmVcCurrentCDC	1.3.6.1.4.1.164.12.2.1.2.2.1.1.14	Gauge32	read-only	Amount of cells dropped in the current 15 minute interval of the VC connection.
G32 atmVcCurrentClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVcCurrentClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.16	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVcCurrentContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.2.1.1.11	Gauge32	read-only	The counter associated with the number of loss of continuity cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.2.1.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.2.1.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentMCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.22	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second).
G32 atmVcCurrentPCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.20	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second).
G32 atmVcCurrentRxAIS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.7	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.2.1.1.4	Gauge32	read-only	The counter associated with the number of received cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.2.1.1.3	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentRxRDI	1.3.6.1.4.1.164.12.2.1.2.2.1.1.9	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentSCR	1.3.6.1.4.1.164.12.2.1.2.2.1.1.21	Gauge32	read-only	The average traffic rate during the last interval of the VC connection.
G32 atmVcCurrentSES	1.3.6.1.4.1.164.12.2.1.2.2.1.1.13	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.24	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVcCurrentShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.25	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
G32 atmVcCurrentShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.23	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
G32 atmVcCurrentTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.19	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVcCurrentTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.2.1.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVcCurrentTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.1.1.15	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVcCurrentTxAIS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.8	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.
G32 atmVcCurrentTxRDI	1.3.6.1.4.1.164.12.2.1.2.2.1.1.10	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.2.1.1.12	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcIntervalCDC	1.3.6.1.4.1.164.12.2.1.2.2.3.1.15	Gauge32	read-only	Amount of cells dropped in the 15 minute interval of the VC connection.
G32 atmVcIntervalClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.19	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVcIntervalClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.17	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVcIntervalContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.2.3.1.12	Gauge32	read-only	The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.2.3.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.2.3.1.7	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalMCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.23	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalPCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.21	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxAIS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.8	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.2.3.1.5	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.2.3.1.4	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalRxRDI	1.3.6.1.4.1.164.12.2.1.2.2.3.1.10	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalSCR	1.3.6.1.4.1.164.12.2.1.2.2.3.1.22	Gauge32	read-only	The average traffic rate during the last interval of the VC connection, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalSES	1.3.6.1.4.1.164.12.2.1.2.2.3.1.14	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.25	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVcIntervalShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.26	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
G32 atmVcIntervalShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.24	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
G32 atmVcIntervalTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.20	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVcIntervalTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.2.3.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVcIntervalTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.2.3.1.16	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVcIntervalTxAIS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.9	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.
G32 atmVcIntervalTxRDI	1.3.6.1.4.1.164.12.2.1.2.2.3.1.11	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.2.3.1.13	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMCurrentECB	1.3.6.1.4.1.164.12.2.1.2.2.2.1.11	Gauge32	read-only	The counter associated with the number of ECBs encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentErroredCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.8	Gauge32	read-only	The counter associated with the number of errored cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentES	1.3.6.1.4.1.164.12.2.1.2.2.2.1.13	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentLostCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.9	Gauge32	read-only	The counter associated with the number of lost cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.2.2.1.10	Gauge32	read-only	The counter associated with the number of misinserted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentRxClp0	1.3.6.1.4.1.164.12.2.1.2.2.2.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentRxClp01	1.3.6.1.4.1.164.12.2.1.2.2.2.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentSECB	1.3.6.1.4.1.164.12.2.1.2.2.2.1.12	Gauge32	read-only	The counter associated with the number of SECBs encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentSES	1.3.6.1.4.1.164.12.2.1.2.2.2.1.14	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentTxClp0	1.3.6.1.4.1.164.12.2.1.2.2.2.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentTxClp01	1.3.6.1.4.1.164.12.2.1.2.2.2.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.2.2.1.15	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
G32 atmVcPMIntervalECB	1.3.6.1.4.1.164.12.2.1.2.2.4.1.12	Gauge32	read-only	The counter associated with the number of ECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalErroredCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.9	Gauge32	read-only	The counter associated with the number of Errored cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalES	1.3.6.1.4.1.164.12.2.1.2.2.4.1.14	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalLostCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.10	Gauge32	read-only	The counter associated with the number of Lost cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.2.4.1.11	Gauge32	read-only	The counter associated with the number of Misinserted cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalRxClp0	1.3.6.1.4.1.164.12.2.1.2.2.4.1.8	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalRxClp01	1.3.6.1.4.1.164.12.2.1.2.2.4.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalSECB	1.3.6.1.4.1.164.12.2.1.2.2.4.1.13	Gauge32	read-only	The counter associated with the number of SECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalSES	1.3.6.1.4.1.164.12.2.1.2.2.4.1.15	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalTxClp0	1.3.6.1.4.1.164.12.2.1.2.2.4.1.6	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalTxClp01	1.3.6.1.4.1.164.12.2.1.2.2.4.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.2.4.1.16	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
G32 atmVcPMQoSCER	1.3.6.1.4.1.164.12.2.1.2.2.7.1.4	Gauge32	read-only	Cell Error Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVcPMQoSCLR	1.3.6.1.4.1.164.12.2.1.2.2.7.1.3	Gauge32	read-only	Cell Loss Ratio counter for the reference period (atmVcPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVcPMQoSCMR	1.3.6.1.4.1.164.12.2.1.2.2.7.1.5	Gauge32	read-only	Cell Miss-insertion Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .
G32 atmVcQoSUAS	1.3.6.1.4.1.164.12.2.1.2.2.6.1.3	Gauge32	read-only	Number of Unavailable Seconds for the reference period (atmVcQoSPeriodRef).
G32 atmVpCurrentCDC	1.3.6.1.4.1.164.12.2.1.2.1.1.1.13	Gauge32	read-only	Amount of cells dropped in the current 15 minute interval of the VP connection.
G32 atmVpCurrentClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVpCurrentClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.15	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 and discarded by the traffic policing entity.
G32 atmVpCurrentContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.1.1.1.10	Gauge32	read-only	The counter associated with the number of loss of continuity cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.1.1.1.4	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.1.1.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentMCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.21	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second).
G32 atmVpCurrentPCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.19	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second).
G32 atmVpCurrentRxAIS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.6	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.1.1.1.3	Gauge32	read-only	The counter associated with the number of received cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.1.1.1.2	Gauge32	read-only	The counter associated with the number of transmitted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentRxRDI	1.3.6.1.4.1.164.12.2.1.2.1.1.1.8	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentSCR	1.3.6.1.4.1.164.12.2.1.2.1.1.1.20	Gauge32	read-only	The average traffic rate during the last interval of the VP connection.
G32 atmVpCurrentSES	1.3.6.1.4.1.164.12.2.1.2.1.1.1.12	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.23	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVpCurrentShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.24	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
G32 atmVpCurrentShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.22	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
G32 atmVpCurrentTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.18	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVpCurrentTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.1.1.1.16	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVpCurrentTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.1.1.14	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVpCurrentTxAIS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.7	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.
G32 atmVpCurrentTxRDI	1.3.6.1.4.1.164.12.2.1.2.1.1.1.9	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.1.1.1.11	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpIntervalCDC	1.3.6.1.4.1.164.12.2.1.2.1.3.1.14	Gauge32	read-only	Amount of cells dropped in the 15 minute interval of the VP connection.
G32 atmVpIntervalClp0CellOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.18	Gauge32	read-only	The total number of valid ATM cells transmitted with CLP=0 by this VPL.
G32 atmVpIntervalClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.16	Gauge32	read-only	The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
G32 atmVpIntervalContinuityLoss	1.3.6.1.4.1.164.12.2.1.2.1.3.1.11	Gauge32	read-only	The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalGcra0Violations	1.3.6.1.4.1.164.12.2.1.2.1.3.1.5	Gauge32	read-only	The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalGcra1Violations	1.3.6.1.4.1.164.12.2.1.2.1.3.1.6	Gauge32	read-only	The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalMCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.22	Gauge32	read-only	MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalPCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.20	Gauge32	read-only	The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxAIS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.7	Gauge32	read-only	The counter associated with the number of received AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxCellsClp0	1.3.6.1.4.1.164.12.2.1.2.1.3.1.4	Gauge32	read-only	The counter associated with the number of received cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxCellsClp01	1.3.6.1.4.1.164.12.2.1.2.1.3.1.3	Gauge32	read-only	The counter associated with the number of transmitted cells , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalRxRDI	1.3.6.1.4.1.164.12.2.1.2.1.3.1.9	Gauge32	read-only	The counter associated with the number of received RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalSCR	1.3.6.1.4.1.164.12.2.1.2.1.3.1.21	Gauge32	read-only	The average traffic rate during the last interval of the VP connection , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalSES	1.3.6.1.4.1.164.12.2.1.2.1.3.1.13	Gauge32	read-only	The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalShaperClp0Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.24	Gauge32	read-only	The total number of CLP0 cells discarded due to congestion by the traffic shaper.
G32 atmVpIntervalShaperClp1Discards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.25	Gauge32	read-only	The total number of CLP1 cells discarded due to congestion by the traffic shaper.
G32 atmVpIntervalShaperTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.23	Gauge32	read-only	The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
G32 atmVpIntervalTaggedOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.19	Gauge32	read-only	The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
G32 atmVpIntervalTotalCellOuts	1.3.6.1.4.1.164.12.2.1.2.1.3.1.17	Gauge32	read-only	The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
G32 atmVpIntervalTotalDiscards	1.3.6.1.4.1.164.12.2.1.2.1.3.1.15	Gauge32	read-only	The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
G32 atmVpIntervalTxAIS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.8	Gauge32	read-only	The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.
G32 atmVpIntervalTxRDI	1.3.6.1.4.1.164.12.2.1.2.1.3.1.10	Gauge32	read-only	The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.1.3.1.12	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMCurrentECB	1.3.6.1.4.1.164.12.2.1.2.1.2.1.10	Gauge32	read-only	The counter associated with the number of ECB, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentErroredCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.7	Gauge32	read-only	The counter associated with the number of errored cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentES	1.3.6.1.4.1.164.12.2.1.2.1.2.1.12	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentLostCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.8	Gauge32	read-only	The counter associated with the number of lost cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.1.2.1.9	Gauge32	read-only	The counter associated with the number of misinserted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentRxClp0	1.3.6.1.4.1.164.12.2.1.2.1.2.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentRxClp01	1.3.6.1.4.1.164.12.2.1.2.1.2.1.5	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentSECB	1.3.6.1.4.1.164.12.2.1.2.1.2.1.11	Gauge32	read-only	The counter associated with the number of SECB, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentSES	1.3.6.1.4.1.164.12.2.1.2.1.2.1.13	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentTxClp0	1.3.6.1.4.1.164.12.2.1.2.1.2.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentTxClp01	1.3.6.1.4.1.164.12.2.1.2.1.2.1.3	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMCurrentUAS	1.3.6.1.4.1.164.12.2.1.2.1.2.1.14	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
G32 atmVpPMIntervalECB	1.3.6.1.4.1.164.12.2.1.2.1.4.1.11	Gauge32	read-only	The counter associated with the number of ECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalErroredCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.8	Gauge32	read-only	The counter associated with the number of Errored cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalES	1.3.6.1.4.1.164.12.2.1.2.1.4.1.13	Gauge32	read-only	The counter associated with the number of Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalLostCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.9	Gauge32	read-only	The counter associated with the number of Lost cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalMisinsertedCells	1.3.6.1.4.1.164.12.2.1.2.1.4.1.10	Gauge32	read-only	The counter associated with the number of Misinserted cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalRxClp0	1.3.6.1.4.1.164.12.2.1.2.1.4.1.7	Gauge32	read-only	The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalRxClp01	1.3.6.1.4.1.164.12.2.1.2.1.4.1.6	Gauge32	read-only	The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalSECB	1.3.6.1.4.1.164.12.2.1.2.1.4.1.12	Gauge32	read-only	The counter associated with the number of SECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalSES	1.3.6.1.4.1.164.12.2.1.2.1.4.1.14	Gauge32	read-only	The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalTxClp0	1.3.6.1.4.1.164.12.2.1.2.1.4.1.5	Gauge32	read-only	The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalTxClp01	1.3.6.1.4.1.164.12.2.1.2.1.4.1.4	Gauge32	read-only	The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMIntervalUAS	1.3.6.1.4.1.164.12.2.1.2.1.4.1.15	Gauge32	read-only	The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
G32 atmVpPMQoSCER	1.3.6.1.4.1.164.12.2.1.2.1.6.1.4	Gauge32	read-only	Cell Error Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVpPMQoSCLR	1.3.6.1.4.1.164.12.2.1.2.1.6.1.3	Gauge32	read-only	Cell Loss Ratio counter for the reference period (atmVpPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.
G32 atmVpPMQoSCMR	1.3.6.1.4.1.164.12.2.1.2.1.6.1.5	Gauge32	read-only	Cell Misinsertion Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .
G32 atmVpQoSUAS	1.3.6.1.4.1.164.12.2.1.2.1.5.1.3	Gauge32	read-only	Number of Unavailable Seconds for the reference period (atmVpQoSPeriodRef).
G32 ethIfCurrentAlignmentErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.5	Gauge32	read-only	The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentCarrierSenseErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.14	Gauge32	read-only	The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentDeferredTransmissions	1.3.6.1.4.1.164.3.1.6.1.2.1.1.12	Gauge32	read-only	The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.6	Gauge32	read-only	The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.27	Gauge32	read-only	The number of received Broadcast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.29	Gauge32	read-only	The number of received Discarded frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.3	Gauge32	read-only	The counter associated with the number of received frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.25	Gauge32	read-only	The number of received Multicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.4	Gauge32	read-only	The counter associated with the number of received octets, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.31	Gauge32	read-only	The number of received Pause frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.1.1.15	Gauge32	read-only	The counter associated with the number of frames dropped due to lack of buffers in ingress pool, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.23	Gauge32	read-only	The number of received Unicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentLateCollisions	1.3.6.1.4.1.164.3.1.6.1.2.1.1.13	Gauge32	read-only	The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentLengthError	1.3.6.1.4.1.164.3.1.6.1.2.1.1.7	Gauge32	read-only	The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.11	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.28	Gauge32	read-only	The number of transmitted Broadcast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.30	Gauge32	read-only	The number of transmitted Discarded frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.8	Gauge32	read-only	The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.26	Gauge32	read-only	The number of transmitted Multicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.9	Gauge32	read-only	The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.32	Gauge32	read-only	The number of transmitted Pause frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOutputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.1.1.16	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the current interval.
G32 ethIfCurrentOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.24	Gauge32	read-only	The number of transmitted Unicast frames, encountered by the Ethernet interface in the current interval.
G32 ethIfCurrentOverflowFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.1.1.19	Gauge32	read-only	The number of times the associated ethIfCurrentFCSErrors counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.37	Gauge32	read-only	The number of times the associated ethIfCurrentInBroadcastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.39	Gauge32	read-only	The number of times the associated ethIfCurrentInDiscardFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.17	Gauge32	read-only	The number of times the associated ethIfCurrentInFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.35	Gauge32	read-only	The number of times the associated ethIfCurrentInMulticastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.18	Gauge32	read-only	The number of times the associated ethIfCurrentInOctets counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.41	Gauge32	read-only	The number of times the associated ethIfCurrentInPauseFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.33	Gauge32	read-only	The number of times the associated ethIfCurrentInUnicastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.22	Gauge32	read-only	The number of times the associated ethIfCurrentMultipleCollisionFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.38	Gauge32	read-only	The number of times the associated ethIfCurrentOutBroadcastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.40	Gauge32	read-only	The number of times the associated ethIfCurrentOutDiscardFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.20	Gauge32	read-only	The number of times the associated ethIfCurrentOutFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.36	Gauge32	read-only	The number of times the associated ethIfCurrentOutMulticastFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.1.1.21	Gauge32	read-only	The number of times the associated ethIfCurrentOutOctets counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.42	Gauge32	read-only	The number of times the associated ethIfCurrentOutPauseFrames counter has overflowed in the current interval.
G32 ethIfCurrentOverflowOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.34	Gauge32	read-only	The number of times the associated ethIfCurrentOutUnicastFrames counter has overflowed in the current interval.
G32 ethIfCurrentSingleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.1.1.10	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the current interval.
G32 ethIfIntervalAlignmentErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.6	Gauge32	read-only	The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the interval.
G32 ethIfIntervalCarrierSenseErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.15	Gauge32	read-only	The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalDeferredTransmissions	1.3.6.1.4.1.164.3.1.6.1.2.2.1.13	Gauge32	read-only	The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.7	Gauge32	read-only	The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.28	Gauge32	read-only	The number of received Broadcast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.30	Gauge32	read-only	The number of received Discarded frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.4	Gauge32	read-only	The counter associated with the number of received frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.26	Gauge32	read-only	The number of received Multicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.5	Gauge32	read-only	The counter associated with the number of received octets, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.32	Gauge32	read-only	The number of received Pause frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalInputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.2.1.16	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Receive direction to the Ethernet interface in the interval.
G32 ethIfIntervalInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.24	Gauge32	read-only	The number of received Unicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalLateCollisions	1.3.6.1.4.1.164.3.1.6.1.2.2.1.14	Gauge32	read-only	The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalLengthError	1.3.6.1.4.1.164.3.1.6.1.2.2.1.8	Gauge32	read-only	The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.12	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.29	Gauge32	read-only	The number of transmitted Broadcast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.31	Gauge32	read-only	The number of transmitted Discarded frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.9	Gauge32	read-only	The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.27	Gauge32	read-only	The number of transmitted Multicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.10	Gauge32	read-only	The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.33	Gauge32	read-only	The number of transmitted Pause frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOutputCongestionDropped	1.3.6.1.4.1.164.3.1.6.1.2.2.1.17	Gauge32	read-only	The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the interval.
G32 ethIfIntervalOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.25	Gauge32	read-only	The number of transmitted Unicast frames, encountered by the Ethernet interface in the interval.
G32 ethIfIntervalOverflowFCSErrors	1.3.6.1.4.1.164.3.1.6.1.2.2.1.20	Gauge32	read-only	The number of times the associated ethIfIntervalFCSErrors counter has overflowed in the interval.
G32 ethIfIntervalOverflowInBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.38	Gauge32	read-only	The number of times the associated ethIfIntervalInBroadcastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.40	Gauge32	read-only	The number of times the associated ethIfIntervalInDiscardFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.18	Gauge32	read-only	The number of times the associated ethIfIntervalInFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.36	Gauge32	read-only	The number of times the associated ethIfIntervalInMulticastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.19	Gauge32	read-only	The number of times the associated ethIfIntervalInOctets counter has overflowed in the interval.
G32 ethIfIntervalOverflowInPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.42	Gauge32	read-only	The number of times the associated ethIfIntervalInPauseFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowInUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.34	Gauge32	read-only	The number of times the associated ethIfIntervalInUnicastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowMultipleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.23	Gauge32	read-only	The number of times the associated ethIfIntervalMultipleCollisionFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutBroadcastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.39	Gauge32	read-only	The number of times the associated ethIfIntervalOutBroadcastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutDiscardFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.41	Gauge32	read-only	The number of times the associated ethIfIntervalOutDiscardFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.21	Gauge32	read-only	The number of times the associated ethIfIntervalOutFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutMulticastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.37	Gauge32	read-only	The number of times the associated ethIfIntervalOutMulticastFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutOctets	1.3.6.1.4.1.164.3.1.6.1.2.2.1.22	Gauge32	read-only	The number of times the associated ethIfIntervalOutOctets counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutPauseFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.43	Gauge32	read-only	The number of times the associated ethIfIntervalOutPauseFrames counter has overflowed in the interval.
G32 ethIfIntervalOverflowOutUnicastFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.35	Gauge32	read-only	The number of times the associated ethIfIntervalOutUnicastFrames counter has overflowed in the interval.
G32 ethIfIntervalSingleCollisionFrames	1.3.6.1.4.1.164.3.1.6.1.2.2.1.11	Gauge32	read-only	The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the interval.
G32 ethIfPerfInOkFrames	1.3.6.1.4.1.164.3.1.6.1.2.4.1.1	Gauge32	read-only	The counter associated with the number of received OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
G32 ethIfPerfInOkOctets	1.3.6.1.4.1.164.3.1.6.1.2.4.1.4	Gauge32	read-only	The counter associated with the number of received OK Octets, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
G32 ethIfPerfOutOkFrames	1.3.6.1.4.1.164.3.1.6.1.2.4.1.2	Gauge32	read-only	The counter associated with the number of transmitted OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
G32 ethIfPerfTotalCollisions	1.3.6.1.4.1.164.3.1.6.1.2.4.1.3	Gauge32	read-only	The counter associated with the total number of collisions of any type encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done
G32 prtDs3CurrentAIS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.4	Gauge32	read-only	The counter associated with the number of AIS seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentBIP	1.3.6.1.4.1.164.3.1.6.3.1.2.1.7	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentBitParity	1.3.6.1.4.1.164.3.1.6.3.1.2.1.12	Gauge32	read-only	Bit Parity Error counter. Relevant to T3 only.
G32 prtDs3CurrentBPV	1.3.6.1.4.1.164.3.1.6.3.1.2.1.17	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the current 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.
G32 prtDs3CurrentES	1.3.6.1.4.1.164.3.1.6.3.1.2.1.11	Gauge32	read-only	The number of Errored Seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentFEBE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.8	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentLCE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.18	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the current 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.
G32 prtDs3CurrentLOC	1.3.6.1.4.1.164.3.1.6.3.1.2.1.3	Gauge32	read-only	The counter associated with the number of LOC seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentLOS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.1	Gauge32	read-only	The counter associated with the number of LOS seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentOOF	1.3.6.1.4.1.164.3.1.6.3.1.2.1.2	Gauge32	read-only	The counter associated with the number of OOF seconds, encountered by a DS3 interface in the current 15 minute interval.
G32 prtDs3CurrentPlcpBIP	1.3.6.1.4.1.164.3.1.6.3.1.2.1.15	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentPlcpFEBE	1.3.6.1.4.1.164.3.1.6.3.1.2.1.16	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentPlcpLOF	1.3.6.1.4.1.164.3.1.6.3.1.2.1.13	Gauge32	read-only	The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configuration If frame types only.
G32 prtDs3CurrentPlcpRAI	1.3.6.1.4.1.164.3.1.6.3.1.2.1.14	Gauge32	read-only	Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3CurrentRDI	1.3.6.1.4.1.164.3.1.6.3.1.2.1.5	Gauge32	read-only	The counter associated with the number of RDI seconds, encountered by a DS3 interface.
G32 prtDs3CurrentSES	1.3.6.1.4.1.164.3.1.6.3.1.2.1.10	Gauge32	read-only	The counter associated with the number of SES encountered by a E3 interface in the current 15 minute interval.
G32 prtDs3CurrentSLM	1.3.6.1.4.1.164.3.1.6.3.1.2.1.9	Gauge32	read-only	The counter associated with the number of SLM seconds, encountered by an E3 (only ) interface in the current 15 minute interval.
G32 prtDs3CurrentUAS	1.3.6.1.4.1.164.3.1.6.3.1.2.1.6	Gauge32	read-only	The counter associated with the number of UAS, encountered by a SONET interface.
G32 prtDs3IntervalAIS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.5	Gauge32	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalBIP	1.3.6.1.4.1.164.3.1.6.3.1.3.1.8	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalBitParity	1.3.6.1.4.1.164.3.1.6.3.1.3.1.13	Gauge32	read-only	Bit Parity Error counter. Relevant to T3 only.
G32 prtDs3IntervalBPV	1.3.6.1.4.1.164.3.1.6.3.1.3.1.18	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.
G32 prtDs3IntervalES	1.3.6.1.4.1.164.3.1.6.3.1.3.1.12	Gauge32	read-only	The number of Errored Seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalFEBE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.9	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalLCE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.19	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.
G32 prtDs3IntervalLOC	1.3.6.1.4.1.164.3.1.6.3.1.3.1.4	Gauge32	read-only	The counter associated with the number of LOC seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalLOS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.2	Gauge32	read-only	The counter associated with the number of LOS seconds , encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalOOF	1.3.6.1.4.1.164.3.1.6.3.1.3.1.3	Gauge32	read-only	The counter associated with the number of OOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalPlcpBIP	1.3.6.1.4.1.164.3.1.6.3.1.3.1.16	Gauge32	read-only	The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalPlcpFEBE	1.3.6.1.4.1.164.3.1.6.3.1.3.1.17	Gauge32	read-only	The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalPlcpLOF	1.3.6.1.4.1.164.3.1.6.3.1.3.1.14	Gauge32	read-only	The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configuration If frame types only.
G32 prtDs3IntervalPlcpRAI	1.3.6.1.4.1.164.3.1.6.3.1.3.1.15	Gauge32	read-only	Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.
G32 prtDs3IntervalRDI	1.3.6.1.4.1.164.3.1.6.3.1.3.1.6	Gauge32	read-only	The counter associated with the number of RDI seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalSES	1.3.6.1.4.1.164.3.1.6.3.1.3.1.11	Gauge32	read-only	The counter associated with the number of SES encountered by a E3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalSLM	1.3.6.1.4.1.164.3.1.6.3.1.3.1.10	Gauge32	read-only	The counter associated with the number of SLM seconds, encountered by an E3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3IntervalUAS	1.3.6.1.4.1.164.3.1.6.3.1.3.1.7	Gauge32	read-only	The counter associated with the number of UAS, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
G32 prtDs3TotalBPV	1.3.6.1.4.1.164.3.1.6.3.1.4.1.17	Gauge32	read-only	Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
G32 prtDs3TotalLCE	1.3.6.1.4.1.164.3.1.6.3.1.4.1.18	Gauge32	read-only	Number of LCE (Link Code Errors) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
G32 prtDs3TotalSES	1.3.6.1.4.1.164.3.1.6.3.1.4.1.19	Gauge32	read-only	Number of SES (Severely Errored Seconds) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
G32 prtDs3TotalUAS	1.3.6.1.4.1.164.3.1.6.3.1.4.1.6	Gauge32	read-only	Number of UASs (Unavailable Seconds) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
G32 prtPhyCurrentES	1.3.6.1.4.1.164.3.1.6.8.2.1.1.5	Gauge32	read-only	The number of Errored Seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentLOF	1.3.6.1.4.1.164.3.1.6.8.2.1.1.7	Gauge32	read-only	The number of Loss of Frames, encountered by an interface in the current 15 minute interval.
G32 prtPhyCurrentLOS	1.3.6.1.4.1.164.3.1.6.8.2.1.1.1	Gauge32	read-only	The counter associated with the number of Loss Of Sync seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentLSV	1.3.6.1.4.1.164.3.1.6.8.2.1.1.2	Gauge32	read-only	The counter associated with the number of Line symbol violation seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentSES	1.3.6.1.4.1.164.3.1.6.8.2.1.1.4	Gauge32	read-only	The counter associated with the number of SES encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyCurrentUAS	1.3.6.1.4.1.164.3.1.6.8.2.1.1.3	Gauge32	read-only	The counter associated with the number of UAS encountered by a 25.6 Mbps interface in the current 15 minute interval.
G32 prtPhyIntervalES	1.3.6.1.4.1.164.3.1.6.8.2.2.1.6	Gauge32	read-only	The number of Errored Seconds, encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalLOF	1.3.6.1.4.1.164.3.1.6.8.2.2.1.8	Gauge32	read-only	The number of Loss of Frames, encountered by an interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalLOS	1.3.6.1.4.1.164.3.1.6.8.2.2.1.2	Gauge32	read-only	The counter associated with the number of Loss Of Sync seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalLSV	1.3.6.1.4.1.164.3.1.6.8.2.2.1.3	Gauge32	read-only	The counter associated with the number of line symbol violation seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalSES	1.3.6.1.4.1.164.3.1.6.8.2.2.1.5	Gauge32	read-only	The counter associated with the number of SES encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtPhyIntervalUAS	1.3.6.1.4.1.164.3.1.6.8.2.2.1.4	Gauge32	read-only	The counter associated with the number of UAS encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
G32 prtT1E1BpvLastMin	1.3.6.1.4.1.164.3.3.3.2.1.1.4	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the number of BPV (BiPolar Violation) events detected during the last minute.
G32 prtT1E1BpvMax	1.3.6.1.4.1.164.3.3.3.2.1.1.5	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the maximal number of BPV (BiPolar Violation) events (per minute), detected during the worst minute.
G32 prtT1E1OosCount	1.3.6.1.4.1.164.3.3.3.2.1.1.3	Gauge32	read-only	This object is applicable only for an E1 active port. It provides the number of red alarm events since the last count clearing.
G32 radBridgeCurrentFrameTypeDiscardedFrames	1.3.6.1.4.1.164.4.1.7.1.1.3	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in the current 15 minute interval.
G32 radBridgeCurrentIngressFilteringDiscardedFrames	1.3.6.1.4.1.164.4.1.7.1.1.2	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in the current 15 minute interval.
G32 radBridgeCurrentRxBcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.7	Gauge32	read-only	The counter associated with the number of Received Broadcast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxCorrectBytes	1.3.6.1.4.1.164.4.1.7.1.1.5	Gauge32	read-only	The counter associated with the number of Received Correct Bytes, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.1.1.6	Gauge32	read-only	The counter associated with the number of times the associated radBridgeCurrentRxCorrectBytes counter has overflowed.
G32 radBridgeCurrentRxCorrectFrames	1.3.6.1.4.1.164.4.1.7.1.1.4	Gauge32	read-only	The counter associated with the number of Received Correct Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentRxMcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.8	Gauge32	read-only	The counter associated with the number of Received Multicast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxBcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.12	Gauge32	read-only	The counter associated with the number of Transmitted Broadcast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxCorrectBytes	1.3.6.1.4.1.164.4.1.7.1.1.10	Gauge32	read-only	The counter associated with the number of Transmitted Correct Bytes, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.1.1.11	Gauge32	read-only	The counter associated with the number of times the associated radBridgeCurrentTxCorrectBytes counter has overflowed.
G32 radBridgeCurrentTxCorrectFrames	1.3.6.1.4.1.164.4.1.7.1.1.9	Gauge32	read-only	The counter associated with the number of Transmitted Correct Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxDropFrames	1.3.6.1.4.1.164.4.1.7.1.1.14	Gauge32	read-only	The counter associated with the number of Transmitted Dropped Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeCurrentTxMcastFrames	1.3.6.1.4.1.164.4.1.7.1.1.13	Gauge32	read-only	The counter associated with the number of Transmitted Multicast Frames, encountered by a Bridge Port in the current 15 minute interval.
G32 radBridgeIntervalFrameTypeDiscardedFrames	1.3.6.1.4.1.164.4.1.7.2.1.4	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalIngressFilteringDiscardedFrames	1.3.6.1.4.1.164.4.1.7.2.1.3	Gauge32	read-only	The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxBcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.8	Gauge32	read-only	The counter associated with the number of Received Broadcast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxCorrectBytes	1.3.6.1.4.1.164.4.1.7.2.1.6	Gauge32	read-only	The counter associated with the number of Received Correct Bytes, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.2.1.7	Gauge32	read-only	The counter associated with the number of times the associated radBridgeIntervalRxCorrectBytes counter has overflowed.
G32 radBridgeIntervalRxCorrectFrames	1.3.6.1.4.1.164.4.1.7.2.1.5	Gauge32	read-only	The counter associated with the number of Received Correct Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalRxMcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.9	Gauge32	read-only	The counter associated with the number of Received Multicast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxBcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.13	Gauge32	read-only	The counter associated with the number of Transmitted Broadcast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxCorrectBytes	1.3.6.1.4.1.164.4.1.7.2.1.11	Gauge32	read-only	The counter associated with the number of Transmitted Correct Bytes, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxCorrectBytesHCOverflow	1.3.6.1.4.1.164.4.1.7.2.1.12	Gauge32	read-only	The counter associated with the number of times the associated radBridgeIntervalTxCorrectBytes counter has overflowed.
G32 radBridgeIntervalTxCorrectFrames	1.3.6.1.4.1.164.4.1.7.2.1.10	Gauge32	read-only	The counter associated with the number of Transmitted Correct Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxDropFrames	1.3.6.1.4.1.164.4.1.7.2.1.15	Gauge32	read-only	The counter associated with the number of Transmitted Dropped Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 radBridgeIntervalTxMcastFrames	1.3.6.1.4.1.164.4.1.7.2.1.14	Gauge32	read-only	The counter associated with the number of Transmitted Multicast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
G32 srvDiscardGreenBytes	1.3.6.1.4.1.164.6.3.8.1.14	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Green.
G32 srvDiscardGreenBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.15	Gauge32	read-only	This attribute displays the number of times that the discardGreenBytes counter has overflowed.
G32 srvDiscardGreenPacket	1.3.6.1.4.1.164.6.3.8.1.6	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Green.
G32 srvDiscardGreenPacketOverflow	1.3.6.1.4.1.164.6.3.8.1.7	Gauge32	read-only	This attribute displays the number of times that the discardGreenPacket counter has overflowed.
G32 srvDiscardRedBytes	1.3.6.1.4.1.164.6.3.8.1.25	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Red.
G32 srvDiscardRedBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.26	Gauge32	read-only	This attribute displays the number of times that the discardRedBytes counter has overflowed.
G32 srvDiscardRedPackets	1.3.6.1.4.1.164.6.3.8.1.23	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Red.
G32 srvDiscardRedPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.24	Gauge32	read-only	This attribute displays the number of times that the discardRedPackets counter has overflowed.
G32 srvDiscardYellowBytes	1.3.6.1.4.1.164.6.3.8.1.21	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Yellow.
G32 srvDiscardYellowBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.22	Gauge32	read-only	This attribute displays the number of times that the discardYellowBytes counter has overflowed.
G32 srvDiscardYellowPackets	1.3.6.1.4.1.164.6.3.8.1.19	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Yellow.
G32 srvDiscardYellowPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.20	Gauge32	read-only	This attribute displays the number of times that the discardYellowPackets counter has overflowed.
G32 srvDiscardYellowRedBytes	1.3.6.1.4.1.164.6.3.8.1.16	Gauge32	read-only	This attribute displays the counted number of discarded bytes that where marked Yellow or Red.
G32 srvDiscardYellowRedBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.17	Gauge32	read-only	This attribute displays the number of times that the discardYellowRedBytes counter has overflowed.
G32 srvDiscardYellowRedPackets	1.3.6.1.4.1.164.6.3.8.1.8	Gauge32	read-only	This attribute displays the counted number of discarded packets that where marked Yellow or Red.
G32 srvDiscardYellowRedPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.9	Gauge32	read-only	This attribute displays the number of times that the discardYellowRedPackets counter has overflowed.
G32 srvForwardGreenBytes	1.3.6.1.4.1.164.6.3.8.1.10	Gauge32	read-only	This attribute displays the counted number of forwarded bytes that where marked Green.
G32 srvForwardGreenBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.11	Gauge32	read-only	This attribute displays the number of times that the forwardGreenBytes counter has overflowed.
G32 srvForwardGreenPackets	1.3.6.1.4.1.164.6.3.8.1.2	Gauge32	read-only	This attribute displays the counted number of forwarded packets that where marked Green.
G32 srvForwardGreenPacktesOverflow	1.3.6.1.4.1.164.6.3.8.1.3	Gauge32	read-only	This attribute displays the number of times that the forwardGreenPackets counter has overflowed.
G32 srvForwardYellowBytes	1.3.6.1.4.1.164.6.3.8.1.12	Gauge32	read-only	This attribute displays the counted number of forwarded bytes that where marked Yellow.
G32 srvForwardYellowBytesOverflow	1.3.6.1.4.1.164.6.3.8.1.13	Gauge32	read-only	This attribute displays the number of times that the forwardYellowBytes counter has overflowed.
G32 srvForwardYellowPackets	1.3.6.1.4.1.164.6.3.8.1.4	Gauge32	read-only	This attribute displays the counted number of forwarded packets that where marked Yellow.
G32 srvForwardYellowPacketsOverflow	1.3.6.1.4.1.164.6.3.8.1.5	Gauge32	read-only	This attribute displays the number of times that the forwardYellowPackets counter has overflowed.
G32 systemOamDescrXcCounter	1.3.6.1.4.1.164.6.2.36.2.1.7	Gauge32	read-only	The number of connections that use this OAM Descriptor.
GenAddress (4)
ADR maskingDestActiveBits	1.3.6.1.4.1.164.4.1.6.3.1.13	GenAddress	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the positions of the wild card characters (*) in the maskingDestAddress field. Only the 1's bit will be taken in considerations.
ADR maskingDestAddress	1.3.6.1.4.1.164.4.1.6.3.1.12	GenAddress	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. The destination address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket. In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles). The IPX socket entered here has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care.
ADR maskingSourceActiveBits	1.3.6.1.4.1.164.4.1.6.3.1.9	GenAddress	read-write	Specifies the positions of the wild card characters (*) in the maskingSourceAddress field. Only the 1's bit will be taken in considerations.
ADR maskingSourceAddress	1.3.6.1.4.1.164.4.1.6.3.1.8	GenAddress	read-write	The source address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles).
IANAifType (1)
IAN ifCreateType	1.3.6.1.4.1.164.6.2.35.1.1.5	IANAifType	read-create	This object indicates the Type of the Interface that is created.
InetAddress (1)
IP systemNtpServerAddress	1.3.6.1.4.1.164.6.2.14.4.4	InetAddress	read-write	This variable represents the NTP Server Address.
InetAddressType (1)
IPt systemNtpServerAddressType	1.3.6.1.4.1.164.6.2.14.4.3	InetAddressType	read-write	This variable represents the NTP Server Address Type.
INTEGER (1212)
INT agnCAgendaCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.1.1.1	INTEGER	read-only	Active or Temporary Agenda Table. Both configurations can be read but only the Temporary can be written to.
INT agnCAgendaDayCategory	1.3.6.1.4.1.164.3.1.2.5.1.1.3	INTEGER	read-write	The Category of the Day
INT agnCAgendaDayIdx	1.3.6.1.4.1.164.3.1.2.5.1.1.2	INTEGER	read-only	Day of week
INT agnCBuMlRole	1.3.6.1.4.1.164.3.1.2.2.12.1.2	INTEGER	not-accessible	The Role of the Link. Primary Link is the Link that should usually work. If the Primary Link fails, the data will go through the Secondary Link. If both Primary and Secondary Links fail, the data will go through the Third Link, provided it is up.
INT agnCBuMlType	1.3.6.1.4.1.164.3.1.2.2.12.1.3	INTEGER	read-write	The Type of the Link. For E1/T1 the Link can be Link A - e1T1a or Link B - e1T1b.
INT agnCClkSrcMode	1.3.6.1.4.1.164.3.1.2.2.4.1.3	INTEGER	read-write	The source of the nodal timing.
INT agnCClkSrcSlt	1.3.6.1.4.1.164.3.1.2.2.4.1.4	INTEGER	read-write	This entry is valid only when we are working in rxClk mode. For an invalid entry, the return value will be '7fff'h.
INT agnCFlipActive	1.3.6.1.4.1.164.3.1.2.5.3.1.3	INTEGER	read-write	Indicates if the entry is valid. In order to Add/Modify parameters of an entry this object should be Set to Yes. In order to delete an entry, this object should be Set to No.
INT agnCFlipCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.3.1.1	INTEGER	read-only	Active or Temporary Flip Decisions Table. Both configurations can be read but only the Temporary can be written to.
INT agnCFlipDbSanityCheckCmd	1.3.6.1.4.1.164.3.1.2.5.4.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and automatically be changed to off(2).
INT agnCFlipDiscardDe	1.3.6.1.4.1.164.3.1.2.5.3.1.6	INTEGER	read-write	Indicates whether the Mux should start discarding all DE. (MP3000 Only).
INT agnCFlipNetEventActive	1.3.6.1.4.1.164.3.1.2.5.2.1.3	INTEGER	read-write	Indicates if the entry is valid. In order to Add/Modify parameters of an entry, this object should be set to Yes. In order to delete an entry, this object should be Set to No.
INT agnCFlipNetEventDayType	1.3.6.1.4.1.164.3.1.2.5.2.1.10	INTEGER	read-write	The time event relates to all days defined in this category in the agnCAgendaTable. Applicable only for time event
INT agnCFlipNetEventsCnfgIdx	1.3.6.1.4.1.164.3.1.2.5.2.1.1	INTEGER	read-only	Active or Temporary Net Events Table. Both configurations can be read but only the Temporary can be written to.
INT agnCFlipNetEventSlot	1.3.6.1.4.1.164.3.1.2.5.2.1.6	INTEGER	read-write	The slot to which the net event relates . Not applicable for time event
INT agnCFlipNetEventType	1.3.6.1.4.1.164.3.1.2.5.2.1.4	INTEGER	read-write	The Net Event type
INT agnClkSrcPortAdminStatus	1.3.6.1.4.1.164.6.2.52.1.1.6	INTEGER	read-create	This object indicates the Recovered Clock Administrative Status.
INT agnClkSrcPortNetType	1.3.6.1.4.1.164.6.2.52.1.1.9	INTEGER	read-create	This object is relevant only in case of Recovery Clock. It indicates the Clock Network Type, i.e. the PSN network characteristics and behavior.
INT agnClkSrcPortQuality	1.3.6.1.4.1.164.6.2.52.1.1.8	INTEGER	read-create	This object indicates the Clock Source Quality.
INT agnClkSrcPortSrcIdx	1.3.6.1.4.1.164.6.2.52.1.1.2	INTEGER	not-accessible	Clock Source Index. master - refers to Master clock fallback - refers to Fallback clock recovered - refers to Recovered clock.
INT agnClkSrcPortState	1.3.6.1.4.1.164.6.2.52.1.1.10	INTEGER	read-only	This object indicates the Clock State. freeRun(1) - Clock recovery is not locked to any clock. frequencyAcquisition(2) - Adaptive clock recovery is learning the frequency. rapidPhaseLock(3) - Clock recovery is in training process till it reaches fine phase lock. finePhaseLock(4) - Clock is locked and clock recovery is qualified and stable. holdover(5) - Clock recovery is in holdover mode. notApplicable(6) - Clock recovery is not applicable. .
INT agnClkSrcPortType	1.3.6.1.4.1.164.6.2.52.1.1.7	INTEGER	read-create	This object is relevant only in case of Recovery Clock. It indicates the Clock Type.
INT agnCMainExitPort	1.3.6.1.4.1.164.3.1.2.2.11	INTEGER	read-write	An object defining the Main Exit Port for the Data of the device. In the Vmux-120 Device the Data can Exit via one of the 2 existing ports: 1. Ethernet port (2) 2. A port that can be E1 or T1 or a Serial Link (3).
INT agnCNetEventsBcast	1.3.6.1.4.1.164.3.1.2.5.4.7	INTEGER	read-write	This object determines if the Net Events will be Broadcasted to other Muxes of the Net or not. disabled - Net Events will NOT be Broadcasted enabled - Net Events will be Broadcasted. Default=disabled. The value will be applied only after performing agnCSaveFlipDbCmd.
INT agnCNetGoCmd	1.3.6.1.4.1.164.3.1.2.5.4.5	INTEGER	read-write	Setting this attribute to On will broadcast a 'GO' command to the network. When a Mux receives a 'GO' command it issues a delay for 'agnCNetDelay' seconds and then activates the DB which was pre-defined by one of the commands : 'agnCSaveNetCnfgIdxCmd' or 'agnCSaveNetFlipDbCmd'.
INT agnCnfgAlrFilter	1.3.6.1.4.1.164.3.1.2.2.8.2.1.6	INTEGER	read-write	An attribute defining if Filter is desired for the alarm . no - no filter. yes - filter activate. This filter is activated within a window of time defined by agnCnfgAlrFilterWindow. Its purpose is to avoid frequent changes of an alarm between ON/OFF states.
INT agnCnfgAlrInvert	1.3.6.1.4.1.164.3.1.2.2.8.2.1.5	INTEGER	read-write	An attribute defining the desired Invert state of an alarm . no - not inverted. yes - inverted. For MP, it is not applicable for alarms that are currently OFF.
INT agnCnfgAlrMask	1.3.6.1.4.1.164.3.1.2.2.8.2.1.4	INTEGER	read-write	An attribute defining the desired Mask state of an alarm . no - unmask (this command is not saved in agent's common database) noAndSave - unmask ; this command is saved in agent's common database yes - mask (this command is not saved in agent's common database) yesAndSave - mask ; this command is saved in agent's common database. Commands that are not saved, will be lost upon power-up or selected card removal.
INT agnCnfgAlrReportType	1.3.6.1.4.1.164.3.1.2.2.8.3.1.1	INTEGER	read-only	The alarm report type. trap - traps will be sent only for alarms having the selected On/Off severity or higher. buffer - only alarms having the selected On/Off severity and higher, will be reported to the buffer. relay - relay contact will be activated only for alarms having the selected On severity or higher. For products having 2 relays, this is the R1 Relay. alrLedOn/alrLedBlink - user should select a higher severity (ReportOn) for alrLedBlink than for alrLedOn (Blinking Led means a more severe alarm than steady ON Led). alrLedOn - MTCL-1 Alarm Led will be ON only when agnSAlrStatusAll equals the selected severity or higher, but lower severity than that selected for 'alrLedBlink'. For products having 2 LEDs, this is the Minor LED. alrLedBlink - MTCL-1 Alarm Led will Blink only when agnSAlrStatusAll equals the selected severity or higher. For products having 2 LEDs, this is the Major LED. relay2 - relay 2 contact will be activated only for alarms having the selected On severity or higher. This is the R2 Relay.
INT agnCnfgAlrSeverity	1.3.6.1.4.1.164.3.1.2.2.8.2.1.9	INTEGER	read-write	An attribute defining desired severity of an alarm code per slot/port
INT agnCnfgAlrSlot	1.3.6.1.4.1.164.3.1.2.2.8.2.1.2	INTEGER	read-only	The alarm slot. The following attributes apply for the alarm code and slot selected. all = the attributes apply to all slots. notApplicable = the selected alarm is for system level. For the Vmux2100 Main Board clA (3) is used.
INT agnCnfgAlrStartReportOff	1.3.6.1.4.1.164.3.1.2.2.8.3.1.3	INTEGER	read-write	This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to OFF state. notApplicable - for 'relay','alrLedOn','alrLedBlink', 'relay2' report types, in MP. noReport - no Report at all (for any severity).
INT agnCnfgAlrStartReportOn	1.3.6.1.4.1.164.3.1.2.2.8.3.1.2	INTEGER	read-write	This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to ON state. noReport - no Report at all (for any severity).
INT agnCOffsetCmd	1.3.6.1.4.1.164.3.1.2.2.9	INTEGER	read-write	An object defining special user request. notApplicable - is RO value for products that do not support this object. normal - nothing special u1 - user 1 - for all Voice cards, the DISPLAYED Tx and Rx Levels will have the following Offsets: - 2 Wires port: Tx Level: the base value (for 0dBm) = 0 Rx Level: the base value (for 0dBm) = -2 - 4 Wires port: Tx Level: the base value (for 0dBm) = -16 Rx Level: the base value (for 0dBm) = 7 The MIB and application DB will use the values without Offset.
INT agnCSanityCheckCmd	1.3.6.1.4.1.164.3.1.2.2.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion the value will automatically be changed to off(2).
INT agnCSaveFlipDbCmd	1.3.6.1.4.1.164.3.1.2.5.4.2	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and if it is OK, it will save the Flip Db in the NVRAM, activating the new Flip DB . If check detects errors, the save will not be performed. Afterwards, the object's value will change automatically to off(2).
INT agnCSaveNetFlipDbCmd	1.3.6.1.4.1.164.3.1.2.5.4.4	INTEGER	read-write	Setting this attribute to on(3) will save the Temp Flip DB Into the NVRAM without actual flip.
INT agnCT1E1RingDualFailDetection	1.3.6.1.4.1.164.3.1.2.2.10.1.9	INTEGER	read-create	T1/E1 Ring - Dual Failure Detection enable/disable.
INT agnCT1E1RingPrimeSlot	1.3.6.1.4.1.164.3.1.2.2.10.1.2	INTEGER	read-only	The slot number of the Primary card of the Ring Pair.
INT agnCT1E1RingSecSlot	1.3.6.1.4.1.164.3.1.2.2.10.1.4	INTEGER	read-create	The slot number of the Secondary card of the Ring Pair.
INT agnCurrClkHoldover	1.3.6.1.4.1.164.6.2.52.2.1.5	INTEGER	read-only	Current Clock Holdover State. As a last resort, in the absence of higher quality timing: - a SONET/SDH object can enter 'holdover' state, until higher quality external timing becomes available again. In this state (value=yes) the SONET/SDH object uses its own timing circuits for clock of the SONET/SDH signal. - for other objects, the 'holdover'=yes state means that the object uses last available clock (stored by the object) for a pre-defined time, until another clock source is used.
INT agnCurrClkMode	1.3.6.1.4.1.164.6.2.52.2.1.2	INTEGER	read-only	Current Clock Source Mode. master - refers Master clock fallback - refers Fallback clock internal - only when both Master and Fallback Sources failed
INT agnCurrClkQualification	1.3.6.1.4.1.164.6.2.52.2.1.8	INTEGER	read-only	This object indicates the Current Clock Qualification and defines whether the PLL can locked according to the stratum definitions.
INT agnCurrClkSrc	1.3.6.1.4.1.164.6.2.52.2.1.3	INTEGER	read-only	This object indicates the Current Clock Source.
INT agnCurrClkSsmBased	1.3.6.1.4.1.164.6.2.52.2.1.6	INTEGER	read-only	This parameter indicates whether clock source is selected based on receive clock quality. Clock quality is indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging).
INT agnCurrClkState	1.3.6.1.4.1.164.6.2.52.2.1.7	INTEGER	read-only	This object indicates the Current Clock State. freeRun(1) - Current clock state machine is not locked and run from the internal oscillator. rapidPhaseLock(2) - Current clock state machine is locked. finePhaseLock(3) - Current clock state machine is in pre-locking. holdover(4) - Current clock state machine is in holdover mode (due to loss of event). .
INT agnDeviceView	1.3.6.1.4.1.164.6.2.37	INTEGER	read-only	This variable denotes the view of the device: Look: old look, new look or new look 2. Material: Plastic or Metal.
INT agnDlciFunnelEnable	1.3.6.1.4.1.164.3.1.2.8.1.1.15	INTEGER	read-create	This object selects Funnel activation: - disabled: Funnel operation will be disabled. The agnDlciTxBe and agnDlciTxBc values are not used for funneling. - enabled : Funnel operation will be enabled both for Source and Destination of the DLCI. The agnDlciTxBe and agnDlciTxBc values are used for funneling calculations. - source: Funnel operation will be enabled only for the Source of the DLCI. - destination:Funnel operation will be enabled only for the Destination of the DLCI. This object is relevant only for an encapsulating DLCI. In case of a Link Selector DLCI, the agnDlciTxBe and agnDlciTxBc values are used for bandwidth of Link Selector. Default=disabled.
INT agnDlciHSltIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.5	INTEGER	read-only	This attribute indicates a unique slot position In the Mux where the DLCI is routed to - Destination Slot. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io16) are not valid
INT agnDlciLSltIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. This is the Source Slot of the DLCI. vs=Voice Switching In the ?004 Unit the entries io6(10)..io16) are not valid. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) LSlotIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
INT agnDlciRoutingProtocol	1.3.6.1.4.1.164.3.1.2.8.1.1.16	INTEGER	read-create	This object is relevant only when one side of the DLCI is a CL-NMS interface. It defines which Routing Protocol will be used for management via CL-NMS port. notApplicable will be used for all slots but CL. rip is a proprietary rip protocol. Default=rip.
INT agnDlciRxBc	1.3.6.1.4.1.164.3.1.2.8.1.1.10	INTEGER	read-create	This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line.
INT agnDlciRxBe	1.3.6.1.4.1.164.3.1.2.8.1.1.11	INTEGER	read-create	This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line.
INT agnDlciSpoofing	1.3.6.1.4.1.164.3.1.2.8.1.1.14	INTEGER	read-create	This object refers to sending of RIP messages: - yes : RIP messages will be sent ONLY if there is a change in the Net. - no : RIP messages will be always sent. This object is relevant only when one side of the DLCI is a CL-NMS interface. Default=no.
INT agnDlciStatus	1.3.6.1.4.1.164.3.1.2.8.1.1.13	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
INT agnDlciTxBc	1.3.6.1.4.1.164.3.1.2.8.1.1.8	INTEGER	read-create	This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line.
INT agnDlciTxBe	1.3.6.1.4.1.164.3.1.2.8.1.1.9	INTEGER	read-create	This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line.
INT agnEgressRateRange	1.3.6.1.4.1.164.6.2.47	INTEGER	read-write	This variable defines the valid ranges of egress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.
INT agnFunction	1.3.6.1.4.1.164.6.2.45.1.1	INTEGER	not-accessible	This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock.
INT agnFunctionActivation	1.3.6.1.4.1.164.6.2.45.1.2	INTEGER	read-write	This MIB object indicates the activation of the current function.
INT agnIndication	1.3.6.1.4.1.164.6.2.8	INTEGER	read-only	Attribute describing the state of the entity the agent is responsible for. In case of a modular entity, the value of this attribute will be according to the component which is in the worst state. The order of severity (from top to bottom) is: critical-> major (or faulty)-> minor-> event-> warning-> normal (off).
INT agnIngressRateRange	1.3.6.1.4.1.164.6.2.49	INTEGER	read-write	This variable defines the valid ranges of ingress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.
INT agnListDecodingAcmRelayPrt	1.3.6.1.4.1.164.3.1.2.7.1.1.7	INTEGER	read-write	This object indicates the ACM port within the slot, desired for outbound relay (report) for the selected alarm. notApplicable - when agnListDecodingType=sanity OR when agnListDecodingAcmRelaySlt=notApplicable.
INT agnListDecodingAcmRelaySlt	1.3.6.1.4.1.164.3.1.2.7.1.1.6	INTEGER	read-write	This object indicates the ACM slot, desired for outbound relay (report) for the selected alarm. In the ?004 Unit the entries io6(10)..io12(16) are not valid. none - when agnListDecodingType=alr AND the selected alarm should not be reported by an ACM card. notApplicable - when agnListDecodingType=sanity OR when [agnListDecodingType=alr and there is no ACM card installed in the Mux].
INT agnListDecodingDefState	1.3.6.1.4.1.164.3.1.2.7.1.1.4	INTEGER	read-only	This object is applicable only for agnListDecodingType=alr. It reports the default state/severity of each alarm. User can change the severity of the alarms defined by this default via the agnListDecodingSeverity object.
INT agnListDecodingSeverity	1.3.6.1.4.1.164.3.1.2.7.1.1.5	INTEGER	read-write	This object is applicable only for agnListDecodingType=alr. It enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code). event - can be set only for an alarm that is defined by default as 'event'. User can change the severity of the alarms defined by default as minor or major. The severity of an event may be set to another severity, but the change will actually happen only if the event threshold is active and passed the Set/ON condition. An event alarm that passed the threshold and changed its severity, will return automatically to event severity when meeting its Reset/OFF condition.
INT agnListDecodingType	1.3.6.1.4.1.164.3.1.2.7.1.1.1	INTEGER	read-only	The type of list the decoding data refers to. alr - Alarms list sanity - Sanity Check Error list. counter - Counter type of ifPerfCounterType
INT agnMonitorModeCmd	1.3.6.1.4.1.164.6.2.9	INTEGER	read-write	Setting this attribute to ON, will enforce the agent to change its mode of operation to Monitor Mode
INT agnNearFarConnection	1.3.6.1.4.1.164.6.2.33	INTEGER	read-only	This parameter describes the connection between near-end and far-end agents.
INT agnNetworkInterfaceType	1.3.6.1.4.1.164.6.2.59	INTEGER	read-write	This MIB object indicates the network interface type to be used by the device. It is used for devices that use only one network port type.
INT agnRadiusAccess	1.3.6.1.4.1.164.6.2.34.3	INTEGER	read-write	Enable/Disable authentication via RADIUS server.
INT agnSAlrInvert	1.3.6.1.4.1.164.3.1.2.1.15.1.8	INTEGER	read-only	Alarm invert : on/off.
INT agnSAlrMask	1.3.6.1.4.1.164.3.1.2.1.15.1.7	INTEGER	read-only	Alarm mask : on/off.
INT agnSAlrSeverity	1.3.6.1.4.1.164.3.1.2.1.15.1.4	INTEGER	read-only	The severity of the alarm.
INT agnSAlrState	1.3.6.1.4.1.164.3.1.2.1.15.1.5	INTEGER	read-only	State of the alarm.
INT agnSAlrStatus	1.3.6.1.4.1.164.3.1.2.1.10	INTEGER	read-only	Indicates the alarm state in the agent level, i.e. lower level (card/port) alarms not included. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSAlrStatusAll	1.3.6.1.4.1.164.3.1.2.1.11	INTEGER	read-only	Indicates the alarm state of the entire agent, i.e. including card and port alarms status. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSClearAllAlrCmd	1.3.6.1.4.1.164.3.1.2.1.17	INTEGER	read-write	Setting this attribute to ON, enforce a clear operation on all MUX alarm events at the levels of agent, slots and ports. The clear operation will not be applied for masked/inverted alarms.
INT agnSClearAlrCmd	1.3.6.1.4.1.164.3.1.2.1.16	INTEGER	read-write	Setting this attribute to ON, enforce a clear operation on all the agent(general) events. General alarms are alarms which are not specific to a card or port. The clear operation will not be applied for masked/inverted alarms.
INT agnSClkSrc	1.3.6.1.4.1.164.3.1.2.1.9	INTEGER	read-only	This entry indicates the source of the system clock.
INT agnSDateFormat	1.3.6.1.4.1.164.3.1.2.1.1	INTEGER	read-write	This entry indicates the date and time format used for the agnSDateAndTimeCmd and for the alarm history report.
INT agnSEditBy	1.3.6.1.4.1.164.3.1.2.1.8	INTEGER	read-only	This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after an update(load) operation.
INT agnSEntryIsValid	1.3.6.1.4.1.164.3.1.2.1.22.1.2	INTEGER	read-only	This attribute indicates whether the specific configuration is valid in the MUX . Value of NO indicates: no such configuration in the MUX.
INT agnSigProfileRxTx	1.3.6.1.4.1.164.3.1.2.10.1.1.3	INTEGER	read-only	This attribute indicates if the following objects refer to: Rx or Tx translation. Rx : ML->IO Tx : IO->ML . For MP-104/204, that means: Rx : Signaling to FXS CH Tx : Signaling to E1 Link.
INT agnSigProfType	1.3.6.1.4.1.164.3.1.2.10.2.1.4	INTEGER	read-write	Profile Type. legacy - usual signaling. The parameters for the Legacy Profiles are detailed in the agnSigProfileTable, above. r2Cas - R2 signaling. The parameters for the R2 Profiles are detailed in the r2 ProfileCnfg tables (belong to r2If).
INT agnSMaskedAlrStat	1.3.6.1.4.1.164.3.1.2.1.12	INTEGER	read-only	Indicates the alarm state in the agent level,[ i.e. lower level (card/port) alarms not included] including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSMaskedAlrStatAll	1.3.6.1.4.1.164.3.1.2.1.13	INTEGER	read-only	Indicates the alarm state of the entire agent, i.e. including card and port alarms status,including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT agnSSanityCheckStatus	1.3.6.1.4.1.164.3.1.2.1.18	INTEGER	read-only	Upon completion of the Sanity check process on the TmpCnfg this attribute will be set to: FAIL(2) - when there is at least one error encountered and possibly some warnings. WARNING(3) - when there are only warnings. otherwise, the value will be OK(4). The value will be UNKNOWN(1) if changes were made in the TmpCnfg following the last Sanity check.
INT agnSshAccess	1.3.6.1.4.1.164.6.2.34.4	INTEGER	read-write	Enable/Disable accessing the device via SSH. disable - no one will be allowed to access the device via SSH. enable - all users are allowed SSH Access. managersOnly - Only manager stations listed in the manager's list are allowed.
INT agnStationClockCard	1.3.6.1.4.1.164.6.2.29	INTEGER	read-only	This entry specifies the station clock card existence and status. notExist - station clock card (piggy) does not exist. notValid - station clock card exists but clock status is not valid. ok - station clock card exists, and its status is OK When the sepcific reason for clock status not being valid is known, it may be reported by lossOfSync or lossOfSignal values.
INT agnStoreCmd	1.3.6.1.4.1.164.6.2.44	INTEGER	read-write	Store command. inFlash(3) = store the current Agent configuration in Flash memory. asDefConfigFile(4) = store the current Agent configuration as Default Configuration file (e.g. 'DefConfig.cfg'). Agent will perform the required command and change automatically the value of this object to off(2).
INT agnSTstStatAll	1.3.6.1.4.1.164.3.1.2.1.14	INTEGER	read-only	on(3) - when there is at least one test in progress in one of the agent cards, otherwise the value will be off(2).
INT agnSwVersionSwapCmd	1.3.6.1.4.1.164.6.2.51	INTEGER	read-write	SW switch command. mainAndBackup (3) = Swap between Main SW and the backup one. Agent will perform the required command and change automatically the value of this object to off(2).
INT agnSyslogFacility	1.3.6.1.4.1.164.6.2.58.2	INTEGER	read-write	A user defined SW module, task or function, from which Syslog messages are sent to the remote Server.
INT agnSyslogSeverityLevel	1.3.6.1.4.1.164.6.2.58.3	INTEGER	read-write	Device will send events equal or exceeding this severity level (configured by user).
INT agnTelnetAccess	1.3.6.1.4.1.164.6.2.34.1	INTEGER	read-write	Enable/Disable accessing the device via Telnet. disable - no one will be allowed to access the device via Telnet. enable - all users are allowed Telnet Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSH) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSH).
INT agnTestStatus	1.3.6.1.4.1.164.6.2.22	INTEGER	read-only	Indicates the current test status (for all levels: system, card, port). This attribute will be set to: on(3): when there is at least one test in progress on the system/card/port off(2): when there is NO test in progress on the system/card/port
INT agnVoiceSwConfDialPlan	1.3.6.1.4.1.164.3.1.2.9.1.1.7	INTEGER	read-write	This is the Dialing Plan method that will be used in the Voice Switching. Static Dialing Plan - Routing is defined by the current device Zone and Node ID in the Network. Static Dialing Plan Plus - Includes the Static Dialing Plan but contains an addition of defining the number of dialed digits. Flexible Dialing Plan - Routing is defined in a flexible form. In this plan the user can configure the extension number of a local voice channel, Route a call to a remote destination and enter the Number of Digits for a specific dial prefix.
INT agnVoiceSwConfHGConnect	1.3.6.1.4.1.164.3.1.2.9.5.1.3	INTEGER	read-write	This attribute indicates whether the hunt group should be considered in any of the mux algorithms.
INT agnVoiceSwConfHGdbIdx	1.3.6.1.4.1.164.3.1.2.9.5.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
INT agnVoiceSwConfHGStatus	1.3.6.1.4.1.164.3.1.2.9.5.1.7	INTEGER	read-write	This object enables the user to create/delete entries in this table. Its usage for values (1)..(6) should be identical to RowStatus SYNTAX. notApplicable(255) - should be used when the table is static (i.e. whenever create/delete entries is not allowed).
INT agnVoiceSwConfIdx	1.3.6.1.4.1.164.3.1.2.9.1.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
INT agnVoiceSwConfRtAction	1.3.6.1.4.1.164.3.1.2.9.2.1.4	INTEGER	read-create	Action that the system should perform for the digits: agnVoiceSwConfRtDigits. The action that is allowed depends on the Dialing Plan. Here is the list of the allowed actions: For Static Dialing Plan - zone, node, in, shortDialing, hgr, del, rep For Static Dialing Plan Plus - zone, node, in, shortDialing, hgr, del, rep, numDigDP For Flexible Dialing Plan - hgr, del, rep, numDigDP, route, ext
INT agnVoiceSwConfRtDbId	1.3.6.1.4.1.164.3.1.2.9.2.1.1	INTEGER	read-only	Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
INT agnVoiceSwConfRtSlot	1.3.6.1.4.1.164.3.1.2.9.2.1.6	INTEGER	read-create	Routing Slot- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13).
INT agnWebAccess	1.3.6.1.4.1.164.6.2.34.2	INTEGER	read-write	Enable/Disable accessing the device via Web. disable - no one will be allowed to access the device via Web. enable - all users are allowed Web Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSL) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSL).
INT alarmForwardingDirection	1.3.6.1.4.1.164.6.2.50.1.10	INTEGER	read-create	This parameter determines the Direction of the Alarm Forwarding. unidirectional - alarmForwardingFailPort affects the alarmForwardingToPort. bidirectional - alarmForwardingFailPort affects the alarmForwardingToPort AND vice-versa. For such cases, this value will be selected, instead of entering an additional unidirectional entry in the table, where the indexes are swapped.
INT alarmForwardingRecoveryCommand	1.3.6.1.4.1.164.6.2.50.1.8	INTEGER	read-create	This parameter is a command. It is applicable when alarmForwardingRecoveryMode = manual. on - Will stop alarm forwarding. After setting to 'On', the agent will set this parameter back to 'Off'.
INT alarmForwardingRecoveryMode	1.3.6.1.4.1.164.6.2.50.1.7	INTEGER	read-create	This parameter determines the Recovery Mode. manual - The user should stop the alarm forwarding by using the alarmForwardingRecoveryCommand. automatic - Alarm forwarding will be automatically stopped upon alarmForwardingFailPort recovery.
INT alarmSeverity	1.3.6.1.4.1.164.6.2.20	INTEGER	read-only	This object specifies the severity of the alarms.
INT alarmState	1.3.6.1.4.1.164.6.2.21	INTEGER	read-only	.
INT alrBufferClearCmd	1.3.6.1.4.1.164.3.1.2.4.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2). For MP-2100/2200, this command will not really erase the Alarm Buffer, but is only an ACK of seeing the Buffer. It marks a pointer of the last entry's alrBufIdx, in order to allow view of new alarms entered after this pointer (alrBufIdxUponLastAck).
INT alrBufSeverity	1.3.6.1.4.1.164.3.1.2.4.1.1.6	INTEGER	read-only	The severity of the alarm.
INT alrBufSlot	1.3.6.1.4.1.164.3.1.2.4.1.1.4	INTEGER	read-only	The slot number this alarm refers to. When the alarm refers to a system alarm, the value will be 'notApplicable(255)'.
INT alrBufState	1.3.6.1.4.1.164.3.1.2.4.1.1.7	INTEGER	read-only	State of the alarm (On/Off).
INT alrGenDefSeverity	1.3.6.1.4.1.164.3.3.4.3.1.7	INTEGER	read-only	This object reports the default severity of each alarm. User can change the severity of the alarms defined by this default via the alrGenSeverity object.
INT alrGenLevel	1.3.6.1.4.1.164.3.3.4.3.1.3	INTEGER	read-only	Alarm level.
INT alrGenSeverity	1.3.6.1.4.1.164.3.3.4.3.1.5	INTEGER	read-write	This object enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code).
INT alrGenSlotType	1.3.6.1.4.1.164.3.3.4.3.1.4	INTEGER	read-only	Slot type that the alarm is relevant to. clAndIo - an alarm that is relevant for both CL and IO slots.
INT atmAlarmForwardingRecoveryCommand	1.3.6.1.4.1.164.12.3.1.1.32.1.6	INTEGER	read-create	This parameter is a command. It is applicable when atmAlarmForwardingRecoveryMode = manual. on - Will stop the RDI transmission. After setting to 'On' the agent will set this parameter back to 'Off'.
INT atmAlarmForwardingRecoveryMode	1.3.6.1.4.1.164.12.3.1.1.32.1.5	INTEGER	read-create	This parameter determines the Recovery Mode. manual - The user should stop the RDI transmission by using the atmAlarmForwardingRecoveryCommand. automatic - The RDI transmission will be automatically stopped upon atmAlarmForwardingFailPort recovery.
INT atmConfAlarmForwarding	1.3.6.1.4.1.164.12.3.2.1.1.1.9	INTEGER	read-write	Enables Path AIS Alarm forwarding upon a failure detection. The following might be considered as a failure: LOS, LOF, LOC, SLM, LOP, Path AIS and Line AIS. disable(2) - will not forward an alarm upon a failure on this port. enable(3) - will forward an alarm upon a failure on this port.
INT atmConfAtmIfVpiVciLimit	1.3.6.1.4.1.164.12.3.2.1.1.1.5	INTEGER	read-only	The limit on the sum of the VPI+VCI bits for this interface.
INT atmConfIfCardType	1.3.6.1.4.1.164.12.3.2.1.1.1.4	INTEGER	read-only	The card type.
INT atmConfIfFrameType	1.3.6.1.4.1.164.12.3.2.1.1.1.3	INTEGER	read-write	The frame type. Valid values for a 155M interface: sonet(2), sdh(3). Valid values for a T3 interface: direct(4), plcpInternal(5), plcpExternal(6), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbling(12). Valid values for Ethernet interface: ethCrcTrans (8), ethCrcNotTrans(9). (DS1 interfaces frame type is specified in the DSX1 mib).
INT atmConfIfHwFeatures	1.3.6.1.4.1.164.12.3.2.1.1.1.6	INTEGER	read-write	HW features command.
INT atmConfIfLoopback	1.3.6.1.4.1.164.12.3.2.1.1.1.2	INTEGER	read-write	Interface Loopback.
INT atmConfIfOamFailureInd	1.3.6.1.4.1.164.12.3.2.1.1.1.13	INTEGER	read-write	This object allows user to define the type of indication (if any) that will be created upon a LB cell failure, for all VCs on which OAM loopback traffic is activated. disabled(2) - no indication will be created. ais(3) - will cause Tx of AIS. rdi(4) - will cause Tx of RDI. aisAndRdi(5) - will cause Tx of AIS & RDI. For LA-110, indication will be sent only for VCs with atmConfVcLoopbackFailureInd <> disabled
INT atmConfIfOamMode	1.3.6.1.4.1.164.12.3.2.1.1.1.12	INTEGER	read-write	OAM support Mode, which determines the interface's location in a segment wise.
INT atmConfIfTransmitClk	1.3.6.1.4.1.164.12.3.2.1.1.1.1	INTEGER	read-write	The transmit clock of the port.
INT atmConfVpCCAdminStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.2	INTEGER	read-write	up(2) - Activate Continuity Check (CC). down(3) - Deactivate CC. source(4) - Activate OAM CC(Continuity Check) of local agent ( start sending Oam cells to the remote side ). sink(5) - Activate CC of remote agent ( start receiving Oam cells from remote side ). listenToActivationCells (6) - Passive listener till gets an activation request originateActivationCells(7) - Sands Activation cell according to atmConfVcCCDirection.
INT atmConfVpCCDirection	1.3.6.1.4.1.164.12.3.2.1.3.1.6	INTEGER	read-write	both(2) - Agent send OAM CC cells and check received OAM CC cells source(4)- Agent send OAM CC cells. sink(5) - Agent checks received OAM CC cells.
INT atmConfVpCCOperStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.9	INTEGER	read-only	initial(1) - The CC activation process is not started. source(4) - Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells. both (8) - OAM CC of local and remote agents activation. timeout (9) - Timeout occured on receiving answer from the remote agent. denied (10) - CC activation process rejected by remote agent. conflict (11) - local and remote sides requested activation simultaneously. manual (12) - OAM CC of local agent activated manually.
INT atmConfVpConnected	1.3.6.1.4.1.164.12.3.2.1.3.1.15	INTEGER	read-write	This object indicates whether this VP is connected and if connected, what is it connected to.
INT atmConfVpLoopbackAdminStatus	1.3.6.1.4.1.164.12.3.2.1.3.1.3	INTEGER	read-write	up(2) - Start loopback OAM cells. down(3) - Stop sending loopback OAM cells. For ace2002: up(2) - Transmitting LB cells with llid all ones (i.e. FFFF..FF) down(3) - Not transmitting LB cells. llid(4) - Transmitting LB cells with llid indicated in the address field. segment(5) - Transmitting Segment LB cells with llid all ones. endToEnd(6) - Transmitting End to End LB cells with llid all ones. segmentLlid(7) - Transmitting Segment LB cells with llid indicated in the address field. endToEndLlid(8) - Transmitting LB cells with llid indicated in the address field. This parameter value might be in conflict with atmConfVpOamSupport value, since this parameter is for LB, while atmConfVpOamSupport is for any other OAM cells.
INT atmConfVpLoopbackFailureInd	1.3.6.1.4.1.164.12.3.2.1.3.1.11	INTEGER	read-write	This object allows user to define the Indication that will be created upon a LB cell failure. disabled(2) - no indication will be created. segmentAis(3) - will cause Tx of a segment AIS. segmentRdi(4) - will cause Tx of a segment RDI. segmentAisAndRdi(5) - will cause Tx of a segment AIS & RDI. endToEndAis(6) - will cause Tx of an End to End AIS. endToEndRdi(7) - will cause Tx of an End to End RDI. endToEndAisAndRdi(8) - will cause Tx of an End to End AIS & RDI. Default: disabled(2).
INT atmConfVpLoopbackTraffic	1.3.6.1.4.1.164.12.3.2.1.3.1.10	INTEGER	read-write	This parameter has both command and status meanings: off(2) - Set to 'Off' will Stop traffic loop. Getting this value means that the loop is not running. on (3) - Set to 'On' will start traffic loop. Getting this value means that the loop is currently running.
INT atmConfVpOamDirection	1.3.6.1.4.1.164.12.3.2.1.3.1.13	INTEGER	read-write	The direction of OAM cell insertion. downStream(2) - The OAM cell will be inserted in downStream. upStream(3) - The OAM cell will be inserted in upStream.
INT atmConfVpOamSupport	1.3.6.1.4.1.164.12.3.2.1.3.1.8	INTEGER	read-write	OAM support mode, which determines the device location in a segment wise.
INT atmConfVpPolicing	1.3.6.1.4.1.164.12.3.2.1.3.1.1	INTEGER	read-write	Policing method desired for this VPL.
INT atmGenSysLogClearAll	1.3.6.1.4.1.164.12.2.2.1.2	INTEGER	read-write	Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).
INT atmGenSysSetDefaultConfg	1.3.6.1.4.1.164.12.2.2.1.4	INTEGER	read-write	When set to on(3), the agent will set all the configuration parameters to their default values. The variable is then reset to off(2) by the agent. The agent must be reset for the default configuration to apply.
INT atmInterfaceAlarmStatus	1.3.6.1.4.1.164.12.3.2.1.2.1.10	INTEGER	read-only	The variable is on(3) when there is any active alarm on this interface.
INT atmLoopbackVcIvlOperStatus	1.3.6.1.4.1.164.12.3.2.2.4.1.5	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VC during this interval. -inProgress(2) has no meaning per interval. -failed(3) means there was problem for this test during this interval. -endSuccessfully(4) means that the test was OK.
INT atmLoopbackVcOperStatus	1.3.6.1.4.1.164.12.3.2.2.2.1.4	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.
INT atmLoopbackVpIvlOperStatus	1.3.6.1.4.1.164.12.3.2.2.3.1.4	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP during this interval. -inProgress(2) has no meaning for an ended interval. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was OK.
INT atmLoopbackVpOperStatus	1.3.6.1.4.1.164.12.3.2.2.1.1.3	INTEGER	read-only	-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.
INT atmNteAlarmType	1.3.6.1.4.1.164.12.3.1.2.11	INTEGER	read-only	This object specifies the type of the alarm.
INT atmNteBridgingMode	1.3.6.1.4.1.164.12.3.1.2.7	INTEGER	read-write	Bridging mode can be one of the following: ATM <> Ethernet - Bridging is between the Ethernet port and the ATM port (there is no bridging between VCs). ATM <> Ethernet + ATM - Bridging is done both between the Ethernet port and the ATM port and also between VCs.
INT atmNteCardCmd	1.3.6.1.4.1.164.12.3.1.2.1.1.6	INTEGER	read-write	Command on the card that is installed in the selected slot. The commands are applicable according to the value of atmNteCardStatus. See the specification document for details. deleteConfig - Deletes the card configuration. deactivate - All the connections state will be changed to NotReady. The card configuration will be blocked. activate - Does the same as done upon card insertion: Initiates the relevant parameters, activates the physical layer, ATM layer and logical layer.
INT atmNteCardStatus	1.3.6.1.4.1.164.12.3.1.2.1.1.5	INTEGER	read-only	Status of the card in the selected slot. notActive - Connections are in NotReady state. No configuration is available for the card. The access to the card HW is blocked. This state is relevant for an extracted card, and for a case in which the card was deactivated. active - The module installed and functions. A card that in this state can be configured. inProgress - The status during proccessing of a command from atmNteCardCmd. empty - No information is valid for the selected slot. This status is relevant to a case in which the card configaration was deleted, or in case in which a slot was empty since the device startup.
INT atmNteCardType	1.3.6.1.4.1.164.12.3.1.2.1.1.4	INTEGER	read-only	The card type.
INT atmNteConfCACMode	1.3.6.1.4.1.164.12.3.1.1.10.1	INTEGER	read-write	CAC support mode. For ACE2002, the following are the applicable values: disable(1), enable(2), 10 - 1000.
INT atmNteConfLoopbackAddMode	1.3.6.1.4.1.164.12.3.1.1.9.3.1	INTEGER	read-write	Loopback addressing mode. on - will enable loopback addressing. off - will disable loopback addressing.
INT atmNteConfOamAIS	1.3.6.1.4.1.164.12.3.1.1.9.2.1	INTEGER	read-write	Defines if a F4 segment OAM cell is transmitted due to problems in the other port, i.e. physical layer alarm or F4 defect. This is valid only when the ACE101 has ATM UNI interfaces in both sides and is configured for 'Non-Intrusive' mode. none - AIS is not sent to any of the ports. user - F4 AIS will be sent toward the user when defect is detected in the network port. network - F4 AIS will be sent toward the network when defect is detected in the user port. both - F4 AIS will be sent toward the network when defect is detected in the user port and toward the user when defect is detected in the network port.
INT atmNteConfOamIfAisRdi	1.3.6.1.4.1.164.12.3.1.1.9.4.1.1	INTEGER	read-write	This parameter controls the generation of F4/F5 AIS and RDI due to lower order problems such as physical layer problems. For AIS: Defines if F4/F5 AIS cell is transmitted due to problems such as physical layer alarm or F4/F5 defect. This is applicable for all ports . off - Problems in this port will not trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. on - Problems in this port will trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. For RDI: Defines if F4/F5 RDI cell will be transmitted due to physical layer problems in that port (in addition to F4/F5 RDI cells transmitted due to ATM layer problems). For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4/F5 RDI cell back to the trunk. The type of F4/F5 (Segment or End-to-End) is according to the configuration of the VPC/VCC.
INT atmNteConfOamRDI	1.3.6.1.4.1.164.12.3.1.1.9.2.2	INTEGER	read-write	Defines if an F4 OAM RDI cell is transmitted due to physical layer problems in the port (in addition to F4 RDI cells transmitted due to ATM layer problems). The type of F4 RDI (Segment or End-to-End) is according to the ACE-101 OAM mode. For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4 RDI cell back to the trunk.
INT atmNteConfOamSupport	1.3.6.1.4.1.164.12.3.1.1.9.1	INTEGER	read-write	OAM support mode, which determines the device location in a segment wise.
INT atmNteConnectionsMaxNumber	1.3.6.1.4.1.164.12.3.1.1.19	INTEGER	read-write	The MAX number of connections supported by system. Setting this parameter will affect the number of MAX intervals supported. This parameter will affect the system only after reset. Changing this parameter from high value to a low value, will be accepted by agent only if the actual used connection <= the desired connection Max number. Applicable to ace2002.
INT atmNteEventType	1.3.6.1.4.1.164.12.3.1.2.9	INTEGER	read-only	This parameter identifies the event. On - the problem exist. Off - the problem not exist. InvalidLogin - Invalid login on local console. CorrectLogin - Successful login operation.
INT atmNteHostVlanTagging	1.3.6.1.4.1.164.12.3.1.1.11.1.11	INTEGER	read-create	VLAN Tag support. no - No support to VLAN. yes - 4 VLAN bytes will be added to each frame connected to this Host.
INT atmNteLevel	1.3.6.1.4.1.164.12.3.1.2.12	INTEGER	read-only	This object specifies the ATM level.
INT atmNteManagerVlanSupport	1.3.6.1.4.1.164.12.3.1.1.1.1.9	INTEGER	read-create	VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
INT atmNteMdlInputPriorityMechanism	1.3.6.1.4.1.164.12.3.3.1.1.1.3	INTEGER	read-write	This object allows the user to Enable/Disable the Input priority mechanism. This object is applicable for modules with more than one port, in which the total ports input may be greater than the port output. disabled - all LAN VCCs will be transmitted through the same queue (queue 1). Upon congestion frames will be dropped randomly. enabled - the user should configure each port/connection priority. Upon congestion frames will be dropped according to priority.
INT atmNteMdlPrtCpuSharing	1.3.6.1.4.1.164.12.3.3.1.1.1.2	INTEGER	read-write	This object lets the user decide what will be the CPU sharing between the ports of the module. This object is applicable for modules in which the same CPU handles the traffic of all ports. equal - All ports will have the same CPU resource. port1 - Port 1 will have higher priority than the other ports.
INT atmNteOamCellType	1.3.6.1.4.1.164.12.3.1.1.26.1.2	INTEGER	read-only	This object indicates a unique Indication Signal. aisAndRdi(1) - Alarm Indication Signal (AIS) and Remote Defect Indication (RDI) cell. loopback(2) - Loopback cell.
INT atmNteOamEnable	1.3.6.1.4.1.164.12.3.1.1.26.1.4	INTEGER	read-write	This parameter determines if the specified OAM cells will be enabled.
INT atmNteOamLevel	1.3.6.1.4.1.164.12.3.1.1.26.1.3	INTEGER	read-only	The level of the OAM cell. -- f4 (2) - VP level, f5 (3) - VC level.
INT atmNteOamMode	1.3.6.1.4.1.164.12.3.1.1.26.1.1	INTEGER	read-only	The OAM cell path. endToEnd(1) - the entire path.
INT atmNtePlugAndPlayActivity	1.3.6.1.4.1.164.12.3.1.1.17	INTEGER	read-write	Activity control for Manager Plug And Play. disable - disable the feature. offline - Automatic learn IP address into offline memory. online - Automatic learn IP address into online memory.
INT atmNteProgCardType	1.3.6.1.4.1.164.12.3.1.2.1.1.7	INTEGER	read-write	The programmed card type.
INT atmNteProtectionMode	1.3.6.1.4.1.164.12.3.1.1.8.1	INTEGER	read-write	Protection Mode. MspOn - Multiplex section protection. pathOn - High order path protection. mspUniOn - Multiplex section Uni-directional protection. mspOneToN - Multiplex section protection.
INT atmNteProtectionSwitchLink	1.3.6.1.4.1.164.12.3.1.1.8.3	INTEGER	read-write	ForceSwitch - will force Switching from the working link to the backup link. Afterwards the agent will set atmNteProtectionSwitchLink back to off(1). atmNteProtectionMode must be either mspOn or pathOn.
INT atmNteProtectionWorkingLink	1.3.6.1.4.1.164.12.3.1.1.8.2	INTEGER	read-write	Selects the working link when atmNteProtectionMode is off.
INT atmNteQosMode	1.3.6.1.4.1.164.12.3.1.1.37	INTEGER	read-write	This variable defines the QoS Mode. disable(1) - QoS is disabled. multipleVc(2) - QoS is enabled and multiple VCs can be bound per bridge port. singleVc(3) - QoS is enabled and only single VC can be bound per bridge port.
INT atmNteRdnManagement	1.3.6.1.4.1.164.12.3.1.1.23	INTEGER	read-only	The redundancy management status.
INT atmNteShaperMode	1.3.6.1.4.1.164.12.3.1.1.12	INTEGER	read-write	Shaper Mode. vpInbandMng - Vcc within a Vp for management.
INT atmNteSlotUsage	1.3.6.1.4.1.164.12.3.1.1.18	INTEGER	read-write	Applicable to ace2002. Slot 2 might be configured as user slot or as network slot.
INT atmNteSysLogClearAll	1.3.6.1.4.1.164.12.3.1.1.4	INTEGER	read-write	Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).
INT atmNteTosMode	1.3.6.1.4.1.164.12.3.1.1.14	INTEGER	read-write	TOS Mode.
INT atmSysConfigCellTestClp	1.3.6.1.4.1.164.12.3.1.1.33.5	INTEGER	read-write	The type of the Cell.
INT atmSysConfigCellTestOamType	1.3.6.1.4.1.164.12.3.1.1.33.6	INTEGER	read-write	The OAM type of the Cell. This object is applicable if atmSysConfigCellTestPti = oamSegment/oamEndToEnd .
INT atmSysConfigCellTestPti	1.3.6.1.4.1.164.12.3.1.1.33.4	INTEGER	read-write	The cell type.
INT atmSysConfigCellTestSendCmd	1.3.6.1.4.1.164.12.3.1.1.33.9	INTEGER	read-write	Setting the variable to send(3) perfroms cell test. The agent will immediately reset the variable to off(2).
INT atmSysNetPrtInUse	1.3.6.1.4.1.164.12.3.1.2.6	INTEGER	read-only	The network port in use.
INT atmSysPSunitsInUse	1.3.6.1.4.1.164.12.3.1.2.3	INTEGER	read-only	The main power supply in this unit.
INT atmTrafficDescrParamMode	1.3.6.1.4.1.164.12.3.1.1.38.1.1	INTEGER	read-create	The Mode of the Traffic Descriptor.
INT atmVcPmAdminStatus	1.3.6.1.4.1.164.12.3.2.3.2.1.4	INTEGER	read-create	up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .
INT atmVcPMCurrentIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.2.2.1.16	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVcPMCurrentLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.2.2.1.17	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
INT atmVcPmDirection	1.3.6.1.4.1.164.12.3.2.3.2.1.5	INTEGER	read-create	The direction of PM.
INT atmVcPMIntervalDir	1.3.6.1.4.1.164.12.2.1.2.2.4.1.3	INTEGER	read-only	The direction of Performance Management.
INT atmVcPMIntervalLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.2.4.1.18	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
INT atmVcPMIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.2.4.1.17	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVcPMQoSDirection	1.3.6.1.4.1.164.12.2.1.2.2.7.1.1	INTEGER	read-only	The direction of performance management.
INT atmVcPMQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.2.7.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
INT atmVcPmSink	1.3.6.1.4.1.164.12.3.2.3.2.1.8	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
INT atmVcPmSource	1.3.6.1.4.1.164.12.3.2.3.2.1.9	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
INT atmVcQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.2.6.1.1	INTEGER	read-only	This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
INT atmVcShaperLevel	1.3.6.1.4.1.164.12.2.1.2.2.8.1.4	INTEGER	read-only	The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VCC.
INT atmVpPmAdminStatus	1.3.6.1.4.1.164.12.3.2.3.1.1.3	INTEGER	read-create	up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .
INT atmVpPMCurrentDir	1.3.6.1.4.1.164.12.2.1.2.1.2.1.2	INTEGER	read-only	The direction of performance management.
INT atmVpPMCurrentIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.1.2.1.15	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVpPMCurrentLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.1.2.1.16	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
INT atmVpPmDirection	1.3.6.1.4.1.164.12.3.2.3.1.1.4	INTEGER	read-create	The direction of PM.
INT atmVpPMIntervalDir	1.3.6.1.4.1.164.12.2.1.2.1.4.1.2	INTEGER	read-only	The direction of performance management.
INT atmVpPMIntervalLastDayQuality	1.3.6.1.4.1.164.12.2.1.2.1.4.1.17	INTEGER	read-only	If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
INT atmVpPMIntervalQuality	1.3.6.1.4.1.164.12.2.1.2.1.4.1.16	INTEGER	read-only	If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
INT atmVpPMQoSDirection	1.3.6.1.4.1.164.12.2.1.2.1.6.1.1	INTEGER	read-only	The direction of performance management.
INT atmVpPMQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.1.6.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
INT atmVpPmSink	1.3.6.1.4.1.164.12.3.2.3.1.1.7	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
INT atmVpPmSource	1.3.6.1.4.1.164.12.3.2.3.1.1.8	INTEGER	read-create	off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
INT atmVpQoSPeriodRef	1.3.6.1.4.1.164.12.2.1.2.1.5.1.1	INTEGER	read-only	This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
INT atmVpShaperLevel	1.3.6.1.4.1.164.12.2.1.2.1.7.1.4	INTEGER	read-only	The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VPC.
INT autoFileTransferScheduling	1.3.6.1.4.1.164.6.2.12.13.1.1.4	INTEGER	read-write	This object defines schedule for TFTP Automatic session(s) initiated by Agent, according to the value selected: now - initiate immediate single session. recurrence- initiate single session 'every M time units'. or 'every N occurrences' or upon both, (earliest event). Time reccurence period (M) is defined by fileTransferTimeRecurrence. Occurrence reccurence (N) is defined by fileTransferOccurrenceRecurrence. Zero value means that the object is not relevant (not taken into account for the recurrence). It is invalid that both will have zero values in our case (recurrence). When both are non zero, file is transferred upon earliest event
INT autoFileTransferType	1.3.6.1.4.1.164.6.2.12.13.1.1.1	INTEGER	read-only	This object defines the type of file to be transferred by agent.
INT cmprSltIdx	1.3.6.1.4.1.164.3.3.4.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. When the unit is stand-alone or this object is not applicable, 255 will be used.
INT cosProfileCosMethod	1.3.6.1.4.1.164.6.3.10.1.3	INTEGER	read-create	Defines the priority method upon CoS mapping is done.
INT dhcpClientAction	1.3.6.1.4.1.164.11.7.2.2.1.6.1.1	INTEGER	read-write	This parameter default value is enable(3). Setting this attribute to disable (2), will disable DHCP Client action for this interface. This parameter can be changed to disable (2) only (it cannot be changed from disable to enable).
INT dhcpPoolAllocFlags	1.3.6.1.4.1.164.11.7.2.2.1.3.1.5	INTEGER	read-only	These flags indicates status of each IP address. User may change value to free, via dhcpPoolAllocFreeCmd
INT dhcpPoolAllocFreeCmd	1.3.6.1.4.1.164.11.7.2.2.1.3.1.6	INTEGER	read-write	Setting this attribute to On (3), will enforce the agent to Free this entry. The Agent will change the value of this MIB object to off(2) automatically, after performing the command. Setting this object to off(2), will do nothing
INT dhcpRelayAction	1.3.6.1.4.1.164.11.7.2.2.1.4.1.1	INTEGER	read-write	Setting this attribute to enable (3), will enable DHCP Relay action for this interface (Only if DHCP Server is disabled for device - wrDhcpAction=disable). dhcpRelayServerIpAddressaddress should not be 0.0.0.0 when enable is set
INT dhcpServerAction	1.3.6.1.4.1.164.11.7.2.2.1.8	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the Server. deleteAllClients (3) is an option that is used for a device functioning as a server. It will remove all the clients from all the interfaces of the device. When the operation is complete, the agent will return a noOp (2) value.
INT dot1agXCfmMdProtocol	1.3.6.1.4.1.164.3.1.6.1.3.8.1.1	INTEGER	read-create	.
INT dot1agXCfmMepCcStat	1.3.6.1.4.1.164.3.1.6.1.3.10.1.1	INTEGER	read-only	This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpectedMep -A MEP detects an Unexpected MEP condition when a CCM frame arrives with the correct MEG level, the correct MEG ID, but an unexpected MEP ID, which includes the MEP's own MEP ID. unexpectedMeLevel - A MEP detects an Unexpected MEG Level condition when a CCM frame arrives with incorrect MEG Level. Incorrect MEG Level is less than the MEP's own MEG level. unexpectedPeriod - A MEP detects an Unexpected Period condition when a CCM frame arrives with a correct MEG level. a correct MEG ID, a correct MEP ID, but with the Period field value different from the MEP's own CCM transmission period. rdi - A MEP detects RDI when it receives a CCM frame with the RDI field set.
INT dot1agXCfmMepContinuityVerMode	1.3.6.1.4.1.164.3.1.6.1.3.9.1.1	INTEGER	read-create	This object determines the OAM behavior of the MEP: disabled - no Continuity Verification is done cc_based - Continuity Verification is done based on incoming CC messages lb_based - Continuity Verification is done based on loopback messages.
INT dot1agXCfmMepDestAddrType	1.3.6.1.4.1.164.3.1.6.1.3.9.1.2	INTEGER	read-create	This object determines if the OAM messages are sent to user defined unicast address, or to RAD proprietary multicast address.
INT dot3OamDescrLbRxOperation	1.3.6.1.4.1.164.3.1.6.1.6.1.1.4	INTEGER	read-create	Since OAM loopback is a disruptive operation (user traffic does not pass), this object provides a mechanism to provide control: whether received OAM loopback commands are processed or ignored, for the OAM Link referencing this Descriptor. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), received loopback commands are processed. The default value is to ignore loopback commands (ignore(1)).
INT dot3OamDescrMode	1.3.6.1.4.1.164.3.1.6.1.6.1.1.3	INTEGER	read-create	This object controls the mode of OAM operation for an Ethernet-like interface referencing this Descriptor. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional capabilities to initiate monitoring activities with the remote OAM peer entity, while passive mode generally waits for the peer to initiate OAM actions with it. As an example, an active OAM entity can put the remote OAM entity in a loopback state, where a passive OAM entity cannot.
INT dot3OamXPeerState	1.3.6.1.4.1.164.3.1.6.1.6.2.1.2	INTEGER	read-only	This object reports the state of the Peer of the OAM EFM Link. unknown - at the initialization of the device, or after Reset, when there is still no data about the peer's state. operational - usually after unknown state, when device senses that peer is OK. linkFault - Loss of Signal is detected by the receiver. dyingGasp - Unrecoverable condition has occurred (e.g power failure) criticalEvent - Unspecified Critical Event has occured.
INT dsx1AisEnable	1.3.6.1.4.1.164.3.1.6.4.2.1.12	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).
INT dsx1CRC6CalcMode	1.3.6.1.4.1.164.3.1.6.4.2.1.22	INTEGER	read-write	This object determines the CRC6 Calculation mode. jtG704 =JT-G704 = the Japanese standard ituG704=ITU-G704 = the International standard This parameter is applicable for J1 only.
INT dsx1CsuLoop	1.3.6.1.4.1.164.3.1.6.4.2.1.18	INTEGER	read-write	This parameter defines where the CSU loop will be done: local - locally (by IPmux) towards the TDM device transparent - transferred to Remote Device that will send it to its connected TDM device. remote - Remote Device will close the loop towards the Local Device.
INT dsx1dBTxGain	1.3.6.1.4.1.164.3.1.6.4.2.1.3	INTEGER	read-write	Transmit line Gain for T1 CSU line mode.
INT dsx1EchoCancelerModule	1.3.6.1.4.1.164.3.1.6.4.2.1.14	INTEGER	read-only	This parameter indicates whether echo-cancellation module exists for this line.
INT dsx1LeasedLine	1.3.6.1.4.1.164.3.1.6.4.2.1.17	INTEGER	read-write	This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).
INT dsx1LineAdaptiveTimingMode	1.3.6.1.4.1.164.3.1.6.4.2.1.10	INTEGER	read-write	Enables end to end clock synchronization. Default value - off.
INT dsx1LineMode	1.3.6.1.4.1.164.3.1.6.4.2.1.2	INTEGER	read-write	T1 device operation mode. Valid for T1 only.
INT dsx1OosSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.20	INTEGER	read-write	This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. 'Mark' = both A and B signaling bits are forced to '1' during out-of-service periods. 'spaceMark' = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. 'markSpace' = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. - '0'= 0 for T1, 1 for E1, or user defined value for Space - '1'= 1 for T1, 0 for E1, or user defined value for Mark.
INT dsx1PortFunction	1.3.6.1.4.1.164.3.1.6.4.2.1.15	INTEGER	read-write	This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as an IMA-ATM. cesPsn - The port will function as a CES-PSN. abis - The port will function as an Abis.
INT dsx1PortMultiplier	1.3.6.1.4.1.164.3.1.6.4.2.1.16	INTEGER	read-write	This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.
INT dsx1RestoreTime	1.3.6.1.4.1.164.3.1.6.4.2.1.5	INTEGER	read-write	Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = CCITT
INT dsx1RxSensitivity	1.3.6.1.4.1.164.3.1.6.4.2.1.4	INTEGER	read-write	Low Sensitivity is considered Short Haul while High Sensitivity is considered Long Haul. The actual values depend on the LIU. Examples: - E1: -12dB is considered Short Haul ; -43dB is considered Long Haul - T1: -12dB is considered Short Haul ; -36dB is considered Long Haul.
INT dsx1Scramble	1.3.6.1.4.1.164.3.1.6.4.2.1.9	INTEGER	read-write	Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicable for E1. active - will scramble/descramble the payload ATM cell notActive - will not scramble/descramble.
INT dsx1SendUponFail	1.3.6.1.4.1.164.3.1.6.4.2.1.23	INTEGER	read-write	This object determines which notification will be sent to the other side upon fail of another interface. In Ipmux14 the notification is sent upon failure of the Ethernet link.
INT dsx1TxClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.11	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered receive clock from another interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'system' indicates that the system clock is used as the transmit clock.
INT dsx3AisEnable	1.3.6.1.4.1.164.3.1.6.3.2.1.1	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet (for TDMoIP) line is disconnected.
INT dsx3TxClockSource	1.3.6.1.4.1.164.3.1.6.3.2.1.2	INTEGER	read-write	The source of Transmit Clock. loopTiming indicates that the recovered receive clock is used as the transmit clock. localTiming indicates that a local clock source is used or that an external clock is attached to the box containing the interface. throughTiming indicates that transmit clock is derived from the recovered receive clock of another DS3 interface. 'system' indicates that the system clock is used as the transmit clock.
INT ethAutoMdiXEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.17	INTEGER	read-write	This parameter defines whether to support automatic change between MDI and MDI[X].
INT ethBackPressure	1.3.6.1.4.1.164.3.1.6.1.1.1.5	INTEGER	read-write	This parameter defines whether to enable or disable Back pressure. Back Pressure is a flow control parameter.
INT ethBridgingMode	1.3.6.1.4.1.164.3.1.6.1.1.1.3	INTEGER	read-write	This object indicates the bridging mode of the Ethernet interface.
INT ethBroadcastBlock	1.3.6.1.4.1.164.3.1.6.1.1.1.9	INTEGER	read-write	This parameter defines whether to send broadcast message to WAN from LAN or not.
INT ethDot1xEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.23	INTEGER	read-write	Determines if the Port-Based Network Access Protocol (IEEE-802.1x) is enabled for the Ethernet Port.
INT ethDot1xPortRole	1.3.6.1.4.1.164.3.1.6.1.1.1.25	INTEGER	read-write	Determine the functionality of the port in the Port-Based Network Access Protocol (IEEE-802.1x) - either Authenticator or Supplicant.
INT ethEncapsulationCRCMode	1.3.6.1.4.1.164.3.1.6.1.1.1.4	INTEGER	read-write	This object define the encapsulation type requested for the Ethernet interface. It indicates if we transfer the Ethernet frame to the other side with or without the CRC.
INT ethIfRingAdminStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.2	INTEGER	read-write	This object denotes the Ethernet Ring administrative status.
INT ethIfRingOperStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.4	INTEGER	read-only	This object indicates the Ethernet Ring operational status.
INT ethIfRingRowStatus	1.3.6.1.4.1.164.3.1.6.1.4.1.1.9	INTEGER	read-write	Implement creation/deletion of rings in the device.
INT ethIfSrcMacCtrl	1.3.6.1.4.1.164.3.1.6.1.7.1.1.3	INTEGER	read-write	Enable or disable the source MAC control on the current interface. The device should not enable source MAC control if for the current interface there are more than ethIfSrcMacCtrlMaxPermitAddr addresses in the ethIfSrcMacCtrlAddrTable. Default value will be: disable (2).
INT ethIfSrcMacCtrlAddrRowStatus	1.3.6.1.4.1.164.3.1.6.1.7.2.1.4	INTEGER	read-write	This MIB object will be used in order to create/delete a static row or delete an address that is not allowed to access the current interface (ethIfSrcMacCtrlAddrStatus= invalid(2)). Device will add the learned addresses to this table. It will not be possible to add a new static entry to this table while the number of existing rows is equal or more than ethIfSrcMacCtrlMaxPermitAddr. When ethIfSrcMacCtrl = enabled (3), the device will add learned entries only up to ethIfSrcMacCtrlMaxPermitAddr.
INT ethIfSrcMacCtrlAddrStatus	1.3.6.1.4.1.164.3.1.6.1.7.2.1.5	INTEGER	read-only	The status of this entry. The meanings of the values are: invalid (2) - the current address is not allowed to access this interface. learned(3) - the current address was learned. mgmt (5) - the current address is static. It may exist in the MAC Table.
INT ethIfSrcMacCtrlFlushAddrCmd	1.3.6.1.4.1.164.3.1.6.1.7.1.1.6	INTEGER	read-write	When set to on (3) this command will erase all the learned addresses and invalid addresses of the selected interface in the ethIfSrcMacCtrlAddrTable. After operation is finished, Agent will turn the value to 'off'.
INT ethIfSrcMacCtrlLocking	1.3.6.1.4.1.164.3.1.6.1.7.1.1.8	INTEGER	read-write	When set to lock (3) this command will lock the Source MAC Address learning. No more learned addresses will be added to the ethIfSrcMacCtrlAddrTable. When set to unlock (2) this command will unlock the Source MAC Address learning. Learned addresses will be added to the ethIfSrcMacCtrlAddrTable but the number of addresses in the table will not exceed ethIfSrcMacCtrlMaxPermitAddr. Default value is: unlock (2).
INT ethIfSrcMacCtrlPortStatus	1.3.6.1.4.1.164.3.1.6.1.7.1.1.11	INTEGER	read-only	This object represents the operational status of the MAC Control feature on an interface. shutdown(2) - This indicates that the port is shutdown due to security violation. secureActive (3) - This indicates that the MAC Control interface security is operational and this interface is not shutdown due to security violation. secureInactive (4)- This indicates that the MAC Control is not operational.
INT ethIfSrcMacCtrlViolationAction	1.3.6.1.4.1.164.3.1.6.1.7.1.1.9	INTEGER	read-write	Determines the action that the device will take upon security violation. drop(2) - the violating packets will be dropped. dropNotify (3)- the violating packets will be dropped and notifications will be generated. Notifications may be for example: SNMP Traps, Syslog messages and log file new entries. shutdown (4) - the interface will be forced to shut down.
INT ethIfStormCtrlEnable	1.3.6.1.4.1.164.3.1.6.1.5.1.1.5	INTEGER	read-write	This object indicates if the Storm Controling is Enabled or Disabled for the relevant entry.
INT ethIfStormDirection	1.3.6.1.4.1.164.3.1.6.1.5.1.1.3	INTEGER	not-accessible	This object indicates the port's Storm Direction.
INT ethJumboFrameEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.16	INTEGER	read-write	This parameter defines whether to support Jumbo Frame or not.
INT ethLimit4	1.3.6.1.4.1.164.3.1.6.1.1.1.6	INTEGER	read-write	This parameter determine the Back off algorithm mode. Every 4 following collisions the Framer will be thrown out (4 times more than usuall).
INT ethLineOam	1.3.6.1.4.1.164.3.1.6.1.1.1.20	INTEGER	read-write	This parameter defines the working mode of 802.AH OAM mechanism.
INT ethMdiXManualSwitch	1.3.6.1.4.1.164.3.1.6.1.1.1.22	INTEGER	read-write	This parameter sets the port to be MDI-X (cross-over) or MDI (straight-through). It is applicable only when ethAutoMdiXEnable = no, namely, only when the automatic MDI/MDIX crossover function is disabled.
INT ethMode	1.3.6.1.4.1.164.3.1.6.1.1.1.2	INTEGER	read-write	This object indicates the Ethernet mode of operation.
INT ethMulticastBlock	1.3.6.1.4.1.164.3.1.6.1.1.1.8	INTEGER	read-write	This parameter defines whether to send multicast message to WAN from LAN or not.
INT ethOamServicePmEnable	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.4	INTEGER	read-create	This object determines PM (Performance Monitoring) shall be enabled or not for the service.
INT ethPartnerRateMode	1.3.6.1.4.1.164.3.1.6.1.1.1.24	INTEGER	read-write	For converters having couples of ports, where each couple contains a port with an SFP connector and a port with a RJ connector, this parameter is relevant for the SFP port. It affects Rate configuration of its partner (RJ port). manual - user can configure manually ETH parameters of RJ port (e.g Autonegotiation, Max Capability Advertised, etc...) automatic - SFP Rate will be enforced on the RJ port. In this mode, user cannot configure the Rate related parameters of the RJ port (e.g Autonegotiation, Max Capability Advertised, etc...)
INT ethPerformanceMode	1.3.6.1.4.1.164.3.1.6.1.2.3	INTEGER	read-write	This object indicates whether OK or Fail statistics will be counted.
INT ethPortDataEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.18	INTEGER	read-write	This parameter defines whether this port is enabled for data (that is not management). no(2) - management can run on this port yes(3) - both management and payload data can run on this port.
INT ethPortMngEnable	1.3.6.1.4.1.164.3.1.6.1.1.1.13	INTEGER	read-write	This parameter defines whether management data can pass through this Port. localOnly (4) - Only local device can be managed via this port.
INT ethPortPriority	1.3.6.1.4.1.164.3.1.6.1.1.1.12	INTEGER	read-write	This parameter defines if priority is to be considered for this Port.
INT ethRip2	1.3.6.1.4.1.164.3.1.6.1.1.1.11	INTEGER	read-write	This parameter defines whether to send RIP II message to WAN from LAN or not
INT ethRoutingProtocol	1.3.6.1.4.1.164.3.1.6.1.1.1.21	INTEGER	read-write	This parameter defines the routing protocol used above ETH port.
INT ethSkipInitReset	1.3.6.1.4.1.164.3.1.6.1.1.1.7	INTEGER	read-write	This parameter defines whether read status on reset.
INT ethSpeed	1.3.6.1.4.1.164.3.1.6.1.1.1.10	INTEGER	read-write	This parameter defines the line speed.
INT fileTransCmd	1.3.6.1.4.1.164.6.2.12.3	INTEGER	read-write	The command to be executed on fileName at fileServerIP.
INT fileTransferProtocol	1.3.6.1.4.1.164.6.2.12.15	INTEGER	read-write	File Transfer protocol used.
INT flowMappingProfilePriority	1.3.6.1.4.1.164.6.3.9.1.1.2	INTEGER	not-accessible	The priority of the Mapping selected by flowMappingProfileMapIndex within the Flow Mapping Profile.
INT gfpPayloadFcs	1.3.6.1.4.1.164.6.2.55.1.1.2	INTEGER	read-write	This object defines whether protocol header will include FCS.
INT gfpRxTxScramble	1.3.6.1.4.1.164.6.2.55.1.1.3	INTEGER	read-write	This object defines whether transmission will be scrambled.
INT gfpVcatHeader	1.3.6.1.4.1.164.6.2.55.1.1.4	INTEGER	read-write	VCAT header is LCAS CONTROL packet as described in the G-7043. one control packet is transmitted in a period of 16 Multi frame
INT hostVlanTagging	1.3.6.1.4.1.164.6.2.40.1.10	INTEGER	read-create	Host VLAN support (Tagging). untag - No support of VLAN Tagging. tag - 4 VLAN bytes will be added to the frame.
INT ifTeQosStatus	1.3.6.1.4.1.164.6.3.3.1.1.6	INTEGER	read-write	This object is used to create, activate and destroy entries of this table.
INT intSwdlCardType	1.3.6.1.4.1.164.6.2.12.10.1.9	INTEGER	read-only	This object defines the Card type that this file is relevant for.
INT intSwdlCmd	1.3.6.1.4.1.164.6.2.12.10.1.7	INTEGER	read-write	The command to down-load a SW file to an object. The Agent will change the value of this MIB object to off(2) automatically, after accepting the command.
INT ip2IfAdminStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.4	INTEGER	read-create	The desired state of the link.
INT ip2IfBundleSensitivity	1.3.6.1.4.1.164.3.1.6.7.1.1.79	INTEGER	read-create	Denotes if the bundle is sensitive to delay in the network, or is sensitive to data errors in the network. Voice bundles are sensitive to delay; Non-voice bundles are sensitive to data errors.
INT ip2IfCallerIdDetection	1.3.6.1.4.1.164.3.1.6.7.1.1.91	INTEGER	read-create	Enable/Disable Caller ID Detection for this bundle.
INT ip2IfCallerIDType	1.3.6.1.4.1.164.3.1.6.7.1.1.72	INTEGER	read-create	Caller ID Type used by the DSP for this bundle. Bellcore type is used by the American method. V.23 type is used by the European method.
INT ip2IfCASRedundancy	1.3.6.1.4.1.164.3.1.6.7.1.1.78	INTEGER	read-create	Enable/Disable CAS signaling redundancy. This parameter is useful when there are problems with the network and applicable only for CAS signaling: E1-MF (G.732S) or E1-CRC-MF (G.732SCRC ). enable (3) - means that each packet containing CAS signaling will be triplicated into 3 packets. disable (2)- No redundancy will exist. Only 1 packet containing CAS will be transmitted.
INT ip2IfClockPreferences	1.3.6.1.4.1.164.3.1.6.7.1.1.57	INTEGER	read-create	The Clock preferences: accurateness (2) = Accurate clock is more important than Constant Delay. constantDelay (3)= Constant Delay is more important than Accurate clock .
INT ip2IfClockSourceEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.46	INTEGER	read-create	This MIB object defines whether this bundle can be a clock source.
INT ip2IfCodingLaw	1.3.6.1.4.1.164.3.1.6.7.1.1.42	INTEGER	read-create	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links.
INT ip2IfComfortNoiseGen	1.3.6.1.4.1.164.3.1.6.7.1.1.65	INTEGER	read-create	Enable or disable Comfort Noise Generation (CNG). When this parameter is enabled and no voice payload exists on the line for some time period during the call (moments of silence), the device will generate a soft background noise which assures the user that the connection is still alive (CNG). When this parameter is disabled and no voice payload exists on the line, absolute silence will be heard (Comfort Noise will not be generated).
INT ip2IfConnectionMode	1.3.6.1.4.1.164.3.1.6.7.1.1.58	INTEGER	read-create	The Connection Mode: tdmOIpCe (2) = TDMOiP (CE) = Circuit Emulation. tdmOIpCv (3)= TDMOiP (CV) = Compressed Voice.
INT ip2IfConnectivityMode	1.3.6.1.4.1.164.3.1.6.7.1.1.45	INTEGER	read-create	This MIB object shows whether to send Pings or OAM frames over the bundle.
INT ip2IfCustomToneDetect	1.3.6.1.4.1.164.3.1.6.7.1.1.43	INTEGER	read-create	Custom Tone Detection (COT) is a Control operation of a 2Khz tone detector. This tone is sent between PBX devices in order to check that the line status is OK. When the COT is enabled the device will not compress/decompress the tone. In this case, if the tone is initiated by the local PBX, the Device runs a 2Khz detector tone and once detected by the Remote Device, if the COT is enabled in the Remote Device, the Remote Device will generate a 2khz tone to the remote PBX.
INT ip2IfCustomToneFrequency	1.3.6.1.4.1.164.3.1.6.7.1.1.69	INTEGER	read-create	This is the frequency of the Custom Tone that is sent between PBXs in order to check that the line status is OK. When the Custom Tone Detection is enabled the device will not compress/decompress this tone. The custom tone that is received from the local PBX will be sent to the remote PBX with the same frequency it was received. When the Custom Tone Frequency is f1780Plus2000Hz (4), the device will not compress/decompress any tone with frequencies of 1780Hz or 2000 Hz.
INT ip2IfDtmfDetection	1.3.6.1.4.1.164.3.1.6.7.1.1.75	INTEGER	read-create	Enable/Disable DTMF (Dual Tone Multi Frequency) detectors for this bundle.
INT ip2IfEchoCanceler	1.3.6.1.4.1.164.3.1.6.7.1.1.41	INTEGER	read-create	Echo canceler activation.
INT ip2IfEthSwitchMode	1.3.6.1.4.1.164.3.1.6.7.13	INTEGER	read-write	This parameter defines whether Eth Switch is in VLAN Tagged mode.
INT ip2IfExitPort	1.3.6.1.4.1.164.3.1.6.7.1.1.15	INTEGER	read-create	This object determines to which external port the traffic will be sent. auto - the device will decide automatically the exit port. If there is an option for Tx via more than one ETH card then use ext1 (1) and ext2(2) for ETH card #1 (ex. LAN1 or Ggabit-ETH1) and use card2Ext1(5) and card2Ext2(6) for card #2 (ex. LAN1 or Ggabit-ETH1). In Vmux-110/210 ext5 is used for ETH-NET, ext 6 is used for E1/T1 link and ext7 is used for Serial Link. In Vmux-2100 Main Board: ext 5 is used for ETH-NET, ext 6 is used for E1/T1 link A, prtE1T1B is used for E1/T1 link B and prtEthUser is used for ETH-User. prt17(10) - prt20(13) values were added in order to support Gmux2000 VMX Card.
INT ip2IfFarEndType	1.3.6.1.4.1.164.3.1.6.7.1.1.23	INTEGER	read-create	This object defines the type of the Far-End device. This data is important for signaling and DS0 format. For Vmux: e1 (2) value is used for a PBX in the Far End. fxs (5) is used for Phone. Other values are not used.
INT ip2IfLogEvents	1.3.6.1.4.1.164.3.1.6.7.12	INTEGER	read-write	This parameter defines whether all Jitter Buffer and Sequence Number events will enter to Log File, or enter those events to Log file in one minute steps.
INT ip2IfMfcSpoofing	1.3.6.1.4.1.164.3.1.6.7.1.1.53	INTEGER	read-create	This MIB object defines whether the MFC (Multi Frequency Compelled) protocol spoofing will exist in the bundle. When the MFC Spoofing is used, the Local and Remote PBXs will send MFC Signaling to each other. The Vmuxes between the PBXs will send proprietary signaling to each other. They will however create and send MFC tones to their local PBX. The PBXs will not know that the actual signaling was not sent from a PBX but from a Vmux.
INT ip2IfMfRelay	1.3.6.1.4.1.164.3.1.6.7.1.1.34	INTEGER	read-create	Multi Frequency Signaling Detection.
INT ip2IfModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.38	INTEGER	read-create	This MIB object shows whether Modem Calls are enabled via the bundle. relay option (3) means that the bundle will send to the network only modulated data.
INT ip2IfMplsRxLabelEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.48	INTEGER	read-create	This MIB object defines whether there is user defined inner (Rx.) label for this Bundle.
INT ip2IfMplsTxLabelEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.50	INTEGER	read-create	This MIB object defines whether there is user defined outer (Tx.) label for this Bundle.
INT ip2IfNetworkType	1.3.6.1.4.1.164.3.1.6.7.1.1.47	INTEGER	read-create	This MIB object defines the network over which the Bundle PSN (Packet Switching Network)is transported. In Gmux2000: ipComprHeader indicates proprietary compressed IP header packets. mplsComprHeader indicates proprietary compressed MPLS header packets.
INT ip2IfNextHopType	1.3.6.1.4.1.164.3.1.6.7.1.1.55	INTEGER	read-create	This MIB object defines the Bundle next Hop Address Type.
INT ip2IfNoiseLevelForVAD	1.3.6.1.4.1.164.3.1.6.7.1.1.56	INTEGER	read-create	This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to handle.
INT ip2IfOAMBundleIdent	1.3.6.1.4.1.164.3.1.6.7.1.1.80	INTEGER	read-create	Denotes if an OAM bundle is identified according to the Bundle Number (0x3fff), or according to the value of the first nibble in the VCCV control word sent in the frame. controlWord - applicable only when ip2IfProtocolVersion = v2(2). When ip2IfProtocolVersion = v1(1), only bundleNumber is applicable.
INT ip2IfOnHookDetect	1.3.6.1.4.1.164.3.1.6.7.1.1.64	INTEGER	read-create	Enables or disable immediate reaction to On-Hook bits from network in Ringing.
INT ip2IfOosTxEnable	1.3.6.1.4.1.164.3.1.6.7.1.1.31	INTEGER	read-create	This object defines whether OOS will be Transmitted. Note that for IPmux1000 the Lbit is always sent, but the OOS will be sent according to user selection in this parameter.
INT ip2IfOperStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.3	INTEGER	read-only	The actual link status. remoteFail - No Rx. localFail - No Tx. unavailable - No echo replay or replay with invalid code or when connection is in Test state. valiodationFail - Connection is in not valid state. standby - offline (can be in pre-sync mode). tdmFail - oper status is down cause of failure in the tdm. hwMismatch - the bundle exists on a card that is not installed or has a different type than the programmed card.
INT ip2IfPayloadType	1.3.6.1.4.1.164.3.1.6.7.1.1.28	INTEGER	read-create	This object defines the TDMoIP payload type.
INT ip2IfPeerAddrType	1.3.6.1.4.1.164.3.1.6.7.1.1.73	INTEGER	read-create	This MIB object defines the peer Address Type.
INT ip2IfPortMask	1.3.6.1.4.1.164.3.1.6.7.9.1.3	INTEGER	read-write	This parameter defines whether Agent will mask port's alarms and statistics or not.
INT ip2IfProtocolVersion	1.3.6.1.4.1.164.3.1.6.7.1.1.29	INTEGER	read-create	This object defines the TDMoIP protocol Version.
INT ip2IfPulseMeter	1.3.6.1.4.1.164.3.1.6.7.1.1.61	INTEGER	read-create	Enables or disable Pulse metering synthesis.
INT ip2IfPulseMeterFreq	1.3.6.1.4.1.164.3.1.6.7.1.1.62	INTEGER	read-create	Frequency of synthesized pulse metering for this bundle.
INT ip2IfRdnState	1.3.6.1.4.1.164.3.1.6.7.1.1.24	INTEGER	read-only	This object defines the role this bundle plays in the redundancy scheme: none(2) - means this bundle is not part of redundancy pair. primary/ secondary - means this bundle is not part of redundancy pair, and that is the primary bundle or the secondary bunle.
INT ip2IfReversePolarity	1.3.6.1.4.1.164.3.1.6.7.1.1.60	INTEGER	read-create	Enables or disable Reverse polarity synthesis.
INT ip2IfRingBack	1.3.6.1.4.1.164.3.1.6.7.1.1.59	INTEGER	read-create	Enables or disable Ring Back.
INT ip2IfSuperTandem	1.3.6.1.4.1.164.3.1.6.7.1.1.36	INTEGER	read-create	The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem allows transmission of compressed voice between a few Vmux 2100 hubs, and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay.
INT ip2IfTDMoIpMode	1.3.6.1.4.1.164.3.1.6.7.1.1.20	INTEGER	read-create	The TDMoIP Mode configuration. Static- means TS can Tx any time. dynamicLES - means TS can Tx only when line is enabled according to LES protocol. dynamicCAS - means TS can Tx only when line is enabled according to CAS protocol. cesOverIp - use for information that this bundle is used for CES Over IP. voiceOverMpls - Voice over Multi Protocol Label Switching. hdlc - High Level Data Link. voIpComprHeader - indicates proprietary compressed IP header packets. voMplsComprHeader - indicates proprietary compressed MPLS header packets.
INT ip2IfUdpMuxMethod	1.3.6.1.4.1.164.3.1.6.7.1.1.90	INTEGER	read-create	This parameter determines according to which field the multiplexing is made: srcPort (2) - multiplexing according to the UDP Source Port (Dest=0x085e). This should be the default value, for backwards compatibility. destPort (3) - multiplexing according to the UDP Destination Port (standard multiplexing). The UDP Source and Destination ports' range is determined according to ip2IfUdpMuxMethod value: For srcPort (2) the range is 1-7000 For destPort (3) the range is 49152-65535.
INT ip2IfV23HD	1.3.6.1.4.1.164.3.1.6.7.1.1.83	INTEGER	read-create	This parameter shows whether V.23 Half Duplex Modem Protocol is enabled on the bundle.
INT ip2IfVadMethod	1.3.6.1.4.1.164.3.1.6.7.1.1.70	INTEGER	read-create	Voice Activity Detection (VAD) method. proprietary (2) - non standard VAD based only on power measurement. It is very sensitive to background noise. internalITUT (3) - standard ITU-T VAD. It is a robust method.
INT ip2IfVbdRate	1.3.6.1.4.1.164.3.1.6.7.1.1.74	INTEGER	read-create	Voice Band Data (VBD) rate for this bundle.
INT ip2IfVlanSupport	1.3.6.1.4.1.164.3.1.6.7.1.1.12	INTEGER	read-create	VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
INT ip2IfVlanTagging	1.3.6.1.4.1.164.3.1.6.7.4	INTEGER	read-write	VLAN support. no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
INT ip2IfWap	1.3.6.1.4.1.164.3.1.6.7.1.1.92	INTEGER	read-create	Enable/Disable WAP (Wireless Application Protocol) for this bundle. WAP allows users to access the internet from wireless devices.
INT lagDistributionMethod	1.3.6.1.4.1.164.6.2.54.1.1.4	INTEGER	read-create	This object defines the criteria for the 802.3ad (LAG) to split the traffic between ports
INT lagLacpEnable	1.3.6.1.4.1.164.6.2.54.1.1.10	INTEGER	read-create	Enabling/Disabling the LACP for a LAG. The LACP will be enabled for all ports belonging to this LAG.
INT lagRdnMethod	1.3.6.1.4.1.164.6.2.54.1.1.9	INTEGER	read-create	This object defines the redundancy method.
INT lagRecoveryMode	1.3.6.1.4.1.164.6.2.54.1.1.5	INTEGER	read-create	This object defines whether traffic will be returned to a port after its recovery. This object is applicable only when lagDistributionMethod= oneToOne (3).
INT linkSelectorMode	1.3.6.1.4.1.164.3.2.3.2.17.2.1.5	INTEGER	read-write	If the link selector is in mode: backup(2)=then the link with the lower priority will be used in case of failure of the higher priority link, bod(3)=bandwidth on demand or dynamic bandwidth allocation means that links with lower priority will be used whenever additional bandwidth is required.
INT linkSelectorRevert	1.3.6.1.4.1.164.3.2.3.2.17.2.1.6	INTEGER	read-write	If the link selector is in mode backup: auto(2)=return automatically to Main link when it is OK. manual(3)=stays connected to backup link.
INT linkSelectorSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.2	INTEGER	read-only	Slot Index
INT mapLinkPrtIdx	1.3.6.1.4.1.164.3.1.5.1.1.3	INTEGER	read-write	This attribute indicates a unique port number.
INT mapLinkSlotIdx	1.3.6.1.4.1.164.3.3.4.2.1.2	INTEGER	read-write	This attribute indicates a unique slot position where the module is inserted.
INT mapLinkSltIdx	1.3.6.1.4.1.164.3.1.5.1.1.2	INTEGER	read-write	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries clA(3), io6(10)..io12(16) are not valid.
INT mapLinkState	1.3.6.1.4.1.164.3.3.4.2.1.4	INTEGER	read-only	This attribute indicates the status of the link between the two muxes
INT mapLinkStatus	1.3.6.1.4.1.164.3.1.5.1.1.4	INTEGER	read-only	This attribute indicates the status of the link between the two muxes
INT markingProfileMethod	1.3.6.1.4.1.164.6.3.12.1.5	INTEGER	read-create	This attribute defines the method upon which marking is done.
INT maskingDestCondition	1.3.6.1.4.1.164.4.1.6.3.1.15	INTEGER	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that matches the content of maskingDestAddress. false - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that does not match the content of maskingDestAddress.
INT maskingDestMacOrNet	1.3.6.1.4.1.164.4.1.6.3.1.14	INTEGER	read-write	If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingDestMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingDestMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingDestMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingDestMacOrNet can be either macAddress or appleAddress. The variable maskingDestAddress and maskingDestActiveBits will be treated as MAC, or NET address.
INT maskingFrameType	1.3.6.1.4.1.164.4.1.6.3.1.6	INTEGER	read-write	Enables the user to decide about frame type * all frame * just broadcast * just multicast.
INT maskingFrameTypeCondition	1.3.6.1.4.1.164.4.1.6.3.1.7	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingFrameType the packet contains data that matches the content of maskingFrameType. fa lse - Condition is valid if at the position specified by maskingFrameType the packet contains data that does not match the content of maskingFrameType.
INT maskingHighLevelProtCondition	1.3.6.1.4.1.164.4.1.6.3.1.19	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that matches the content of maskingHighLevelProt. false - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that does not match the content of maskingHighLevelProt.
INT maskingLowLevelProt	1.3.6.1.4.1.164.4.1.6.3.1.16	INTEGER	read-write	This field is set in conjunction with the maskingProtocolType variable. This variable specifies the low level protocol. The IPX socket entered in maskingDestAddress has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care.
INT maskingLowLevelProtCondition	1.3.6.1.4.1.164.4.1.6.3.1.17	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that matches the content of maskingLowLevelProt. false - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that does not match the content of maskingLowLevelProt.
INT maskingOperation	1.3.6.1.4.1.164.4.1.6.3.1.22	INTEGER	read-write	The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list. smartMask = the operation and destination of the mask will be determined by the objects of the Smart Table (old masking table: radBridgeMaskTable). If maskingType is codConnect, the 'block' value is NOT allowed. If maskingType is codDisconnect, the 'forward' value is NOT allowed.
INT maskingPortNumCondition	1.3.6.1.4.1.164.4.1.6.3.1.21	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingPortNum the packet contains data that matches the content of maskingPortNum. false - Condition is valid if at the position specified by maskingPortNum the packet contains data that does not match the content of maskingPortNum. This object is applicable only when maskingPortNum is applicable.
INT maskingProtocolType	1.3.6.1.4.1.164.4.1.6.3.1.4	INTEGER	read-write	The base protocol for masking. IPX, IP, others.
INT maskingSourceCondition	1.3.6.1.4.1.164.4.1.6.3.1.11	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that matches the content of maskingSourceAddress. false - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that does not match the content of maskingSourceAddress.
INT maskingSourceMacOrNet	1.3.6.1.4.1.164.4.1.6.3.1.10	INTEGER	read-write	The variable maskingSourceAddress and maskingSourceActiveBits will be treated as MAC, or NET address. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingSourceMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingSourceMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingSourceMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingSourceMacOrNet can be either macAddress or appleAddress.
INT maskingSrcPortNumCondition	1.3.6.1.4.1.164.4.1.6.3.1.24	INTEGER	read-write	The same as 'maskingPortNumCondition'. Relates to source port.
INT maskingType	1.3.6.1.4.1.164.4.1.6.3.1.1	INTEGER	read-only	Defines the type of mask entry.
INT mdlAlarmInvert	1.3.6.1.4.1.164.3.3.2.1.3.1.1.6	INTEGER	read-only	Alarm Invert is : on/off.
INT mdlAlarmMask	1.3.6.1.4.1.164.3.3.2.1.3.1.1.5	INTEGER	read-only	Alarm Mask is : on/off.
INT mdlAlarmOnOff	1.3.6.1.4.1.164.3.3.2.1.3.1.1.7	INTEGER	read-only	Alarm state is : on/off.
INT mdlAlrMaskSltIdx	1.3.6.1.4.1.164.3.3.2.1.3.2.1.1	INTEGER	read-only	This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.
INT mdlAlrSltIdx	1.3.6.1.4.1.164.3.3.2.1.3.1.1.2	INTEGER	read-only	This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.
INT mdlAlrState	1.3.6.1.4.1.164.3.3.2.1.3.1.1.4	INTEGER	read-only	This object indicates the card alarm severity.
INT mdlCDhcpClientEnable	1.3.6.1.4.1.164.3.1.3.2.1.1.7	INTEGER	read-write	Enable/Disable the feature of DHCP Client for the selected card.
INT mdlClIdx	1.3.6.1.4.1.164.3.3.2.2.1.1.1	INTEGER	read-only	This object indicates the Cl slot referred.
INT mdlCmprSltIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
INT mdlCPrgCardType	1.3.6.1.4.1.164.3.1.3.2.1.1.3	INTEGER	read-write	This attribute indicates the type of card assigned to the specific slot in the common configuration. This object is identical in all the configurations (1..100). Only the TmpCnf(255) may have different value. The write operation is valid only to the TmpCnfg entry.
INT mdlCProgCardType	1.3.6.1.4.1.164.3.3.2.1.2.1.3	INTEGER	read-write	This object indicates the card type assigned to the specific slot in the common configuration. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. The write operation is valid only for the TmpCnfg entry.
INT mdlCRdnExists	1.3.6.1.4.1.164.3.1.3.2.1.1.8	INTEGER	read-only	This object indicates whether any port of the programmed card is configured to be part of a Redundancy/APS pair. If at least one port of the programmed card is configured to be part of a Redundancy/APS pair, the value will be 'yes'. Otherwise, it will be 'no'.
INT mdlCSlotIdx	1.3.6.1.4.1.164.3.3.2.1.2.1.2	INTEGER	read-only	This object indicates a unique number of the slot position in which the module is inserted. The Kilomux should use enumerated values starting with kmx.
INT mdlCSltIdx	1.3.6.1.4.1.164.3.1.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
INT mdlCWorkMode	1.3.6.1.4.1.164.3.1.3.2.1.1.6	INTEGER	read-write	Working mode of the card. The user may configure the card to work in a stand alone mode or integrated with the device. Example for use in MHS-IP cards: - standAlone - in this mode, the router works so that data is received via the LAN (Eth) port and is transmitted via the WAN (HS) external port without going through the MPH device. - integrated - in this mode, the router works so that it is integrated in the MPH and routes DLCIs into the device.
INT mdlPbxFraEnhEcho	1.3.6.1.4.1.164.3.2.2.1.1.1.1.3	INTEGER	read-write	Refers to external ports of an analogue module and to the internal ports of the other mvc4 types of modules. ms16(3) means that the four voice ports have enhanced echo of 16ms. ms32(4) means that the two first ports have enhanced echo of 32 ms while the last two ports have no enhanced echo.
INT mdlPbxFraFramerSlot	1.3.6.1.4.1.164.3.2.2.1.1.1.1.8	INTEGER	read-write	Slot where is sitting the Framer.
INT mdlPbxFraSignaling	1.3.6.1.4.1.164.3.2.2.1.1.1.1.9	INTEGER	read-write	Signaling - describes the way the signaling ABCD bits pass from the local extension to the remote extension and vice-versa. endToEnd = the signaling ABCD bits pass without change from local to remote extension. localTermination = the signaling ABCD bits received from the local extension are translated to different ON Hook/OFF Hook bit values and then passed to remote extension. This is relevant when the Local and Remote ON Hook/OFF Hook values are different.
INT mdlPbxFraSignalMode	1.3.6.1.4.1.164.3.2.2.1.1.1.1.5	INTEGER	read-write	Refers to the signaling mode of the Framer module. tieTrunk(2), tieInvert(3), casTrans(4) are standard coding of the signaling protocol. casTrans(4) is Channel Associated Signaling (the signaling is within the channels time slot). ccsTrans(6) is Transparent Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). userDefined(5) allows the user to define the signaling protocol he wants. In this case, the next two MIB fields are relevant.
INT mdlPbxFraSltIdx	1.3.6.1.4.1.164.3.2.2.1.1.1.1.2	INTEGER	read-only	The slot relevant to this module.
INT mdlPbxFraTSGroupAss	1.3.6.1.4.1.164.3.2.2.1.1.1.1.4	INTEGER	read-write	In case of T1 modules: group1=(1,2,3,4), ...., group6=(21,22,23,24) while in case of E1 modules: - If prtExPh1MlLineType=g732sE1 or g732sE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,17), group5=(18,19,20,21),...,group7=(26,27,28,29) group8=(30,31). - If prtExPh1MlLineType=g732nE1 or g732nE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,16), group5=(17,18,19,20),...,group7=(25,26,27,28) group8=(29,30,31).
INT mdlProtIpSlotIdx	1.3.6.1.4.1.164.3.2.2.1.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the 2104 Unit the entries io6(10)..io16) are not valid.
INT mdlPsIdx	1.3.6.1.4.1.164.3.3.2.3.1.1.1	INTEGER	read-only	This object indicates the PS card referred.
INT mdlPsStatus	1.3.6.1.4.1.164.3.3.2.3.1.1.2	INTEGER	read-only	This object indicates the status of the PS card.
INT mdlPsTestResult	1.3.6.1.4.1.164.3.3.2.3.1.1.3	INTEGER	read-only	This object indicates the result of the PS card test. ok (1) - the test passed successfully. f12V (2) - 12V FAIL was detected f5V (3) - 5V FAIL was detected.
INT mdlSActivity	1.3.6.1.4.1.164.3.3.2.1.1.1.9	INTEGER	read-only	notApplicable - when the slot is empty (no module) offline(1) - when the module is not active (redundant) online (2) - when the module is active .
INT mdlSAlarmStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.5	INTEGER	read-only	Indicates the current alarm state only for card level. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT mdlSAlarmStatusAll	1.3.6.1.4.1.164.3.3.2.1.1.1.6	INTEGER	read-only	Indicates the current card alarm state including the lower level: card, port. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT mdlSAlrClearAllCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.11	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on card and port level alarms . Upon completion, the value will automatically change to off(2).
INT mdlSAlrClearCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.10	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the card level alarms . Upon completion, the value will automatically change to off(2).
INT mdlSAlrInvert	1.3.6.1.4.1.164.3.1.3.1.2.1.9	INTEGER	read-only	Alarm invert : on/off.
INT mdlSAlrMask	1.3.6.1.4.1.164.3.1.3.1.2.1.8	INTEGER	read-only	Alarm mask : on/off.
INT mdlSAlrMaskAll	1.3.6.1.4.1.164.3.3.2.1.1.1.12	INTEGER	read-write	on(3) - will cause masking of all the card level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all card level alarms except those masked via the mdlAlrMaskTable.
INT mdlSAlrSeverity	1.3.6.1.4.1.164.3.1.3.1.2.1.5	INTEGER	read-only	The severity of the alarm.
INT mdlSAlrSltIdx	1.3.6.1.4.1.164.3.1.3.1.2.1.2	INTEGER	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
INT mdlSAlrState	1.3.6.1.4.1.164.3.1.3.1.2.1.6	INTEGER	read-only	State of the alarm.
INT mdlSAlrStatus	1.3.6.1.4.1.164.3.1.3.1.1.1.5	INTEGER	read-only	Indicates the alarm state at module level, i.e. lower level (port alarms) status is not included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSAlrStatusAll	1.3.6.1.4.1.164.3.1.3.1.1.1.6	INTEGER	read-only	Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSCardType	1.3.6.1.4.1.164.3.3.2.1.1.1.2	INTEGER	read-only	This attribute indicates the type of the card installed in the specific slot position. Only PS's are possible in the PS slots. Only CL's are possible in the CL slots. Only IO modules are possible in the IO slots. Kmux card type start with the letter k. LA card type start with the letters la.
INT mdlSClearAllAlrCmd	1.3.6.1.4.1.164.3.1.3.1.1.1.11	INTEGER	read-write	Setting this command to ON, enforces a clear of all the alarms in the given slot, including all its ports alarms. The clear operation will not be applied for masked/inverted alarms.
INT mdlSClearAlrCmd	1.3.6.1.4.1.164.3.1.3.1.1.1.10	INTEGER	read-write	Setting this command to ON, enforces a clear of all the alarms in the given slot, excluding alarms of port level. The clear operation will not be applied for masked/inverted alarms.
INT mdlSHwStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.8	INTEGER	read-only	This attribute will be fail(2) when a HW FAIL exists on this module (discovered by periodic self test); otherwise the value will be ok(3).
INT mdlSInstCardType	1.3.6.1.4.1.164.3.1.3.1.1.1.2	INTEGER	read-only	This attribute indicates the type of card installed in the specific slot position. Only PS cards are possible in the PS slots. Only CL cards are possible in the CL slots. Only IO cards are possible in the IO slots.
INT mdlSInstSltIdx	1.3.6.1.4.1.164.3.1.3.1.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the mux. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
INT mdlSMaskedAlrStat	1.3.6.1.4.1.164.3.1.3.1.1.1.7	INTEGER	read-only	Indicates the alarm state at module level, [i.e. lower level (port alarms) status is not included],including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSMaskedAlrStatAll	1.3.6.1.4.1.164.3.1.3.1.1.1.8	INTEGER	read-only	Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT mdlSRebuildFrame	1.3.6.1.4.1.164.3.3.2.1.1.1.15	INTEGER	read-write	Applicable only for KiloMux Main Link cards only. '2' = off, this will be always the Get value. '3' = on, this is the Set command used to Rebuild the Frame. Upon completing the operation, the value will automatically change to off(2), by Agent.
INT mdlSReset	1.3.6.1.4.1.164.3.3.2.1.1.1.14	INTEGER	read-write	Reset action to be performed on the module.
INT mdlSSltIdx	1.3.6.1.4.1.164.3.3.2.1.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the DACS. The Kilomux should use enumerated values starting with kmx. For IPmux100 use values 1-13, 20.
INT mdlStatSltIdx	1.3.6.1.4.1.164.3.2.2.2.1.1.1	INTEGER	read-only	A unique number to identify a slot position in the mux. In the 2104 Unit the entries psB(2),clB(4),io6(10)..io12(16) are not valid.
INT mdlSTestStatus	1.3.6.1.4.1.164.3.3.2.1.1.1.7	INTEGER	read-only	This attribute will be on(3) when there is at least one test running on a port of the module; otherwise the value will be off(2).
INT mdlSTstStatusAll	1.3.6.1.4.1.164.3.1.3.1.1.1.9	INTEGER	read-only	This attribute will be set to on(3) when there is at least one test in progress on a channel of the card, otherwise the value will be off(2).
INT modlParamReset	1.3.6.1.4.1.164.6.2.32.1.1.1.2	INTEGER	read-write	Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2).
INT modlParamSwdlStatus	1.3.6.1.4.1.164.6.2.32.1.1.1.3	INTEGER	read-only	This parameter indicates whatever the swdl is in process or not.
INT modlParamType	1.3.6.1.4.1.164.6.2.32.1.1.1.5	INTEGER	read-only	This attribute indicates the Module Type.
INT optPrtCnfgALS	1.3.6.1.4.1.164.6.2.15.8.2.1.3	INTEGER	read-write	enable/disable Automatic Laser Shutdown
INT optPrtMonitorSample	1.3.6.1.4.1.164.6.2.15.8.1.1.2	INTEGER	not-accessible	This index indicates historic and current values - minimum, maximum and actual (current) value.
INT physicalConnector	1.3.6.1.4.1.164.6.2.15.1.1.2	INTEGER	read-only	The connector of the port/interface. other - none of the specified connectors none - no connector.
INT pLinkSlotNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.5	INTEGER	read-write	The slot of the prioritized link. For ISDN BRI ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
INT pLinkSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.2	INTEGER	read-only	Slot Index
INT pLinkVRate	1.3.6.1.4.1.164.3.2.3.2.17.3.1.8	INTEGER	read-write	The rate to use with this link.
INT portBalance	1.3.6.1.4.1.164.6.2.15.1.1.5	INTEGER	read-write	This object is according to the port Impedance. For T1 - always balanced. For E1 - there are different impedance values for balanced and unbalanced.
INT portDdmSupport	1.3.6.1.4.1.164.6.2.15.1.1.6	INTEGER	read-only	SFP (Small Form Pluggable) port -support Digital Diagnostics Monitoring.
INT portOptMode	1.3.6.1.4.1.164.6.2.15.1.1.4	INTEGER	read-only	Laser Mode of an Optical Laser interface/port. notApplicable - for non-Laser ports.
INT portOptWaveLength	1.3.6.1.4.1.164.6.2.15.1.1.3	INTEGER	read-only	Wave Length of an Optical interface/port in [nm] and specification if Laser or not. notApplicable - for non-optical ports.
INT prtAcmActiveState	1.3.6.1.4.1.164.3.2.3.2.20.1.1.5	INTEGER	read-write	This attribute indicates the Electric Active State of the port.
INT prtAcmConnect	1.3.6.1.4.1.164.3.2.3.2.20.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.
INT prtAcmPrtIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtAcmSltIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
INT prtAgendaBehaviourOnOff	1.3.6.1.4.1.164.3.1.4.2.2.1.1.4	INTEGER	read-write	Setting this command to on(3) enables the agenda function at module (3000) or port (300/30) level.
INT prtBdbandIndEvent	1.3.6.1.4.1.164.3.1.6.8.1.1.1.4	INTEGER	read-only	This object indicates a unique Event that can cause the Indication Signal. slm(2) = SLM = Signal Label Mismatch eed(4) = EED = Excessive Error Defect pathTrace(5) = the end-to-end source/destination of information is wrong. lom(6) = LOM = Loss of Multiframe. lop(7) = LOP = Loss of Pointer. slu(8) = SLU = Signal Label Unequipped.
INT prtBdbandIndSig	1.3.6.1.4.1.164.3.1.6.8.1.1.1.3	INTEGER	read-only	This object indicates a unique Indication Signal. ais(1) = AIS = Alarm Indication Signal. rdi(2) = RDI = Remote Defect Indication.
INT prtBdbandIndSigEnable	1.3.6.1.4.1.164.3.1.6.8.1.1.1.5	INTEGER	read-create	This object allows user to define if the event specified by prtBdbandIndEvent will cause creation of the Indication Signal specified by prtBdbandIndSig or not. disable - will not enable causing the signal enable - will enable causing the signal.
INT prtBertClearCounters	1.3.6.1.4.1.164.3.3.3.1.5.1.10	INTEGER	read-write	Setting this object to ON, will enforce a clear operation of some BERT Counters. Upon completion, the value will automatically change to off(2).
INT prtBertInjectErrRateCmd	1.3.6.1.4.1.164.3.3.3.1.5.1.4	INTEGER	read-write	This object controls activation/deactivation of the Error Rate Injection during BERT.
INT prtBertInjectRate	1.3.6.1.4.1.164.3.3.3.1.5.1.3	INTEGER	read-write	This object indicates the error rate injection of the BERT. r10Emx = 10E-x This object is the same for all configurations. single - single error injection. notApplicable - when this object is not supported.
INT prtBertInjectSingleErrCmd	1.3.6.1.4.1.164.3.3.3.1.5.1.5	INTEGER	read-write	This object enables to initiate a Single Error Injection during BERT (on). Upon completion, the value will automatically change to off(2).
INT prtBertPattern	1.3.6.1.4.1.164.3.3.3.1.5.1.2	INTEGER	read-write	This object indicates the pattern of the BERT. p2Exxm1 = 2Exx-1. pxx = pattern xx. This object is the same for all configurations. notApplicable - when this object is not supported.
INT prtBertSyncStatus	1.3.6.1.4.1.164.3.3.3.1.5.1.11	INTEGER	read-only	Sync Status while BERT runs.
INT prtCfgParamInbandLoopDetection	1.3.6.1.4.1.164.3.3.3.1.7.1.1.7	INTEGER	read-write	Inband Loop Detection. The field is relevant for FCD-T1/E1(L) ports.
INT prtCfgParamInbandLoopPatternCfg	1.3.6.1.4.1.164.3.3.3.1.7.1.1.8	INTEGER	read-write	This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtCfgParamInbandLoopActPattern and prtCfgParamInbandLoopDeactPattern.
INT prtCfgParamMlAtoMlBPrio	1.3.6.1.4.1.164.3.3.3.1.7.1.1.5	INTEGER	read-write	ML-A to ML-B Priority. The field is relevant only for ML modes of Priority Bumping and Switched Backup.
INT prtCfgParamMlBtoMlAPrio	1.3.6.1.4.1.164.3.3.3.1.7.1.1.6	INTEGER	read-write	ML-B to ML-A Priority. The field is relevant only for ML modes of Priority Bumping.
INT prtCfgParamOperatedMl	1.3.6.1.4.1.164.3.3.3.1.7.1.1.4	INTEGER	read-write	The main link for this channel. The field is relevant only for ML modes of Dual, Priority Bumping and Switched Backup.
INT prtCfgParamSlt	1.3.6.1.4.1.164.3.3.3.1.7.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid. notApplicable(255) - for products that do not have Slots.
INT prtClkSrcIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.3	INTEGER	not-accessible	An index in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
INT prtClkSrcMode	1.3.6.1.4.1.164.6.2.15.7.1.1.4	INTEGER	read-write	This entry indicates the source the nodal timing is locked to.
INT prtCmprSltIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.4	INTEGER	read-only	This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
INT prtCnfgAgendaDayIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.4	INTEGER	read-only	This attribute for which day of the week this row applies.
INT prtCrStatisInvIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.3	INTEGER	read-only	The Interval of 15 min. for which the following statistics counters are applicable.
INT prtCrStatisPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtCrStatisSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
INT prtDestConnect	1.3.6.1.4.1.164.3.3.3.5.2.1.5	INTEGER	read-only	Connection Status of the specified destination number. For a specified destination port, it depends both on the status of the port and on the status of the far-end port. Since this is a RO object, same value will be received for all configurations.
INT prtDimClkMode	1.3.6.1.4.1.164.3.3.3.5.1.1.5	INTEGER	read-write	Clock Mode. smooth - a clock that is not 'pulsed'(has no 'gaps'). In this mode the DXC does NOT receive back the clock signal. extSmooth - same as 'smooth' but in this mode, the DXC receives back the clock signal.
INT prtDimMaxDelay	1.3.6.1.4.1.164.3.3.3.5.1.1.6	INTEGER	read-write	Max Delay permitted between the links, in msec.
INT prtDimMng	1.3.6.1.4.1.164.3.3.3.5.1.1.7	INTEGER	read-write	Use of DIM port for management. disabled - no management on DIM ts1 - 1 bit of TS1 is used for management.
INT prtDimMngRoutProt	1.3.6.1.4.1.164.3.3.3.5.1.1.8	INTEGER	read-write	Mng Routing Protocol of the port. none - when prtDimMng is 'disabled'.
INT prtDimPolarity	1.3.6.1.4.1.164.3.3.3.5.1.1.4	INTEGER	read-write	Polarity.
INT prtDimTxMode	1.3.6.1.4.1.164.3.3.3.5.1.1.3	INTEGER	read-write	Tx mode. regularTx - the links are connected to a similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is decreased accordingly. broadcast - the links are connected to MORE than one similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is not affected
INT prtDlciCmprPrtIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.4	INTEGER	read-only	This attribute indicates a unique identifier of the port the compressed information relates to. All the values are valid.
INT prtDlciCmprSltIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.3	INTEGER	read-only	This attribute indicates a unique number of the slot position where the module is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
INT prtDlciPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtDlciSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
INT prtE2Connect	1.3.6.1.4.1.164.3.2.3.2.21.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.
INT prtE2MngOnNationalBit	1.3.6.1.4.1.164.3.2.3.2.21.1.1.5	INTEGER	read-write	This attribute indicates whether National Bit will be used for Management or not.
INT prtE2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtE2SltIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
INT prtExClDataBits	1.3.6.1.4.1.164.3.2.3.2.1.1.1.6	INTEGER	read-only	This attribute indicates the number of data bits in async frame
INT prtExClEnabled	1.3.6.1.4.1.164.3.2.3.2.1.1.1.10	INTEGER	read-only	This attribute indicates if Ethernet port of CL is enabled or not for management. It is applicable only on the ETH port of the CL, when the MP includes an ML-IP card. disabled - will happen when there is Inband Management via the ML-IP link/s enabled - will happen when ML-IP link/s is not used for Inband Management, but CL's ETH port .
INT prtExClParity	1.3.6.1.4.1.164.3.2.3.2.1.1.1.7	INTEGER	read-only	This attribute indicates if the parity operation mode in async frame
INT prtExClPrtIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtExClRate	1.3.6.1.4.1.164.3.2.3.2.1.1.1.5	INTEGER	read-only	This attribute indicates the operation rate of the port.
INT prtExClRoutingProtocol	1.3.6.1.4.1.164.3.2.3.2.1.1.1.9	INTEGER	read-only	This attribute indicates the routing protocol of the port. When prtExClUsage is nmsSlip or nmsPpp - all values are applicable . Else - only 'none' is applicable.
INT prtExClSltIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. Because the second Cl is only for redundancy, all the parameters are identical in the two modules, i.e. change of any parameter in one module will change automatically the value of the other module.. In the ?004 Unit the entry clB(4) is not valid.
INT prtExClStopBits	1.3.6.1.4.1.164.3.2.3.2.1.1.1.8	INTEGER	read-only	This attribute indicates the minimum number of stop bits in the tx async frame
INT prtExClUsage	1.3.6.1.4.1.164.3.2.3.2.1.1.1.4	INTEGER	read-only	This attribute indicates what is the usage of the port.
INT prtExHs4Connect	1.3.6.1.4.1.164.3.2.3.2.7.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithm. It also affects all the module considerations because the card has only one external (physical) interface.
INT prtExHs4LineCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.6	INTEGER	read-write	This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the MPH.1/T1 and E1 line code parameters for the MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExHs4LineLen	1.3.6.1.4.1.164.3.2.3.2.7.1.1.7	INTEGER	read-write	This attribute is the line length parameter used only for T1 interfaces. len399p533ft=len-399-533ft
INT prtExHs4LineType	1.3.6.1.4.1.164.3.2.3.2.7.1.1.5	INTEGER	read-write	This attribute is the line type parameter for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the HS-4/1 and E1 line code parameters for the HS-4/2. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) dsx1ESF (2) dsx1D4 (3) dsx1E1 (4) dsx1E1-CRC (5) dsx1E1-MF (6) dsx1E1-MF-CRC (7)
INT prtExHs4MfClkSrcPrt	1.3.6.1.4.1.164.3.2.3.2.7.1.1.13	INTEGER	read-write	A unique number to identify a port position in the mux if the MultiFrame clock source is valid (YES). inPrt1 - for MTML-H/E1 cards.
INT prtExHs4MfClkSrcSlt	1.3.6.1.4.1.164.3.2.3.2.7.1.1.12	INTEGER	read-write	This attribute indicates whether the port Tx is multiframe synchronized with Rx multiframe of another port and the slot position of that port. This opration is required in order to bypass signaling of PCM voice channels. When its value is Local(2) there is no meaning to 'prtExHs4MfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExHs4OosCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.10	INTEGER	read-write	OOS Code
INT prtExHs4OosSig	1.3.6.1.4.1.164.3.2.3.2.7.1.1.9	INTEGER	read-write	Out of Service signal type.
INT prtExHs4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExHs4RestoreT	1.3.6.1.4.1.164.3.2.3.2.7.1.1.8	INTEGER	read-write	Time passing from the disappearance of the loss of synchronization condition (red alarm), to the restoration of normal service.
INT prtExHs4SltIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
INT prtExHs4TsIConPrt	1.3.6.1.4.1.164.3.2.3.2.7.2.1.6	INTEGER	read-write	This attribute indicates the internally (In Mux) connected/routed port.
INT prtExHs4TsIConSlot	1.3.6.1.4.1.164.3.2.3.2.7.2.1.5	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS).
INT prtExHs4TsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.3	INTEGER	read-only	This attribute indicates a unique port number. Hs4/T1 and Hs4/T1 cards have only one external interface.
INT prtExHs4TsSltIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExHsfBcastRingSrcPort	1.3.6.1.4.1.164.3.2.3.2.6.1.14	INTEGER	read-write	This object is applicable only when prtExHsfOperMode= bidirBcastRing. In this case, the values mean: - none - this port will be connected to ML in TSA as usual. - exPrt1.. exPrtX ; X=maximum ports of the card in focus : it means that the same TS that is assigned in TSA to this port is actually connected also to this port, for Broadcast Ring mode. Therefore, this port should NOT be connected to ML in TSA.
INT prtExHsfClkMode	1.3.6.1.4.1.164.3.2.3.2.6.1.6	INTEGER	read-write	This attribute indicates a unique port operation clock mode.
INT prtExHsfClkPolarity	1.3.6.1.4.1.164.3.2.3.2.6.1.12	INTEGER	read-write	This object indicates the clock polarity. For FCD-M this object will be applicable only for the fixed HS port (the fixed port on the device).
INT prtExHsfConnect	1.3.6.1.4.1.164.3.2.3.2.6.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExHsfControlSignal	1.3.6.1.4.1.164.3.2.3.2.6.1.13	INTEGER	read-write	This object indicates the Control Signal according to G.797 ITU-T standard. For FCD-M this object will be applicable for the fixed HS port (the fixed port on the device) and HS-Q/N channels. Local and End to End are applicable only when channel Interface type is RS-530, else it will be Not Applicable.
INT prtExHsfCts	1.3.6.1.4.1.164.3.2.3.2.6.1.7	INTEGER	read-write	This attribute indicates a unique CTS control line operation mode.
INT prtExHsfFifoSize	1.3.6.1.4.1.164.3.2.3.2.6.1.8	INTEGER	read-write	Size in bits.
INT prtExHsfInbandLoopback	1.3.6.1.4.1.164.3.2.3.2.6.1.11	INTEGER	read-write	This object indicates if Inband Loopback from the Network should be enabled or disabled.
INT prtExHsfLinkTo	1.3.6.1.4.1.164.3.2.3.2.6.1.9	INTEGER	read-write	This attribute indicates a slot of Main Link module, that the port is linked to. This object is the same for all the ports in the specific card because of HW limitations. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExHsfOperMode	1.3.6.1.4.1.164.3.2.3.2.6.1.10	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request. bidirBcastRing = Bidirectional Broadcast Ring. When this value is selected, AND RTS=On, the port opens its transmission channel.
INT prtExHsfRate	1.3.6.1.4.1.164.3.2.3.2.6.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtExHsiActType	1.3.6.1.4.1.164.3.2.3.2.8.1.1.8	INTEGER	read-write	It indicates the Activation Type. Activation Type is the Synchronization type towards the PBX. It is applicable only when prtExHsiInterface=nt. notApplicable - for cards that do not support this object, or when prtExHsiInterface is NOT nt.
INT prtExHsiConnect	1.3.6.1.4.1.164.3.2.3.2.8.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. v51 - this port is connected to a V5.1 interface. All rest of the values will be 'notApplicable' in this case. V5 MIB will be used instead. v52 - this port is connected to a V5.2 interface. All rest of the values will be 'notApplicable' in this case. V5 MIB will be used instead.
INT prtExHsiInterface	1.3.6.1.4.1.164.3.2.3.2.8.1.1.7	INTEGER	read-write	It indicates the interface type: lt = line termination nt = network termination te = terminal equipment. lt1 - for ASMi-31 connection (not ISDN) For MP: For HS-U/I only 'lt' and 'nt' are applicable. For HS-U/1 only 'lt' is applicable. For HS-S , only 'te' and 'nt' are applicable. For HS-U, this object is not applicable. For HS-U6, HS-U12, are applicable: 'lt'=lt-i,'nt'=nt-i, lt1. For DXC: For HS-U8, HS-U16, are applicable: 'lt'=LT-I,'nt'=NT-I, 'lt1'=LT-1.
INT prtExHsiLinkTo	1.3.6.1.4.1.164.3.2.3.2.8.1.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the HS-? card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExHsiRate	1.3.6.1.4.1.164.3.2.3.2.8.1.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtExHsiSltIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
INT prtExHsrClkMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.11	INTEGER	read-write	Clock mode. This object is applicable for Sync protocol only.
INT prtExHsrConnect	1.3.6.1.4.1.164.3.2.3.2.10.1.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtExHsrCts	1.3.6.1.4.1.164.3.2.3.2.10.1.1.10	INTEGER	read-write	CTS. This object is applicable for Async protocol only.
INT prtExHsrDataBits	1.3.6.1.4.1.164.3.2.3.2.10.1.1.7	INTEGER	read-write	Data Bits. This object is applicable for Async protocol only.
INT prtExHsrDcdDsr	1.3.6.1.4.1.164.3.2.3.2.10.1.1.13	INTEGER	read-write	DCD & DSR.
INT prtExHsrEncapsMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.20	INTEGER	read-write	Low Speed encapsulation method over PCM. When Encapsulation mode is Latency optimized, only rates up to 19.2 are supported. In this case a double number of bits occupy the Time Slot. For up to 9.6 Kbps - 4 bits are occupied. For 14.4 & 19.2 Kbps - 8 bits are occupied. When Encapsulation Mode is Bandwidth Optimized: For up to 9.6 Kbps - 2 bits are occupied. For 14.4 & 19.2 Kbps - 4 bits are occupied. For higher rates - 8 bits are occupied.
INT prtExHsrLinkTo	1.3.6.1.4.1.164.3.2.3.2.10.1.1.12	INTEGER	read-write	It indicates the slot of the main link card to which the HS-R card is mapped. notApplicable - for HS-U/1 internal ports. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExHsrLlbEnable	1.3.6.1.4.1.164.3.2.3.2.10.1.1.16	INTEGER	read-write	Enable/Disable LLB.
INT prtExHsrOperMode	1.3.6.1.4.1.164.3.2.3.2.10.1.1.14	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request.
INT prtExHsrParity	1.3.6.1.4.1.164.3.2.3.2.10.1.1.8	INTEGER	read-write	- For HS-R card, this object indicates if the parity bit is needed or not. Therefore, the 'no' and 'yes; values are applicable. - For HS-S12, HS-U12, the parity type is selected: no, odd, even. This object is applicable for Async protocol only.
INT prtExHsrProtocol	1.3.6.1.4.1.164.3.2.3.2.10.1.1.5	INTEGER	read-write	This object indicates the protocol.
INT prtExHsrRate	1.3.6.1.4.1.164.3.2.3.2.10.1.1.6	INTEGER	read-write	This object indicates the port speed. The 16,32,48,56,64 and 128 kbps rates are applicable only for Sync protocol. The 57.6 and 115.2 kbps rates are applicable only for Async protocol. notConnected= 0 rate.
INT prtExHsrRateAdapt	1.3.6.1.4.1.164.3.2.3.2.10.1.1.18	INTEGER	read-write	Rate Adaptation - takes a low rate and adapts it to 64Kbps. This object specifies the means this adaptation is done by.
INT prtExHsrRemoteModem	1.3.6.1.4.1.164.3.2.3.2.10.1.1.19	INTEGER	read-write	Remote modem. asmi31s2 = ASMi-31/2
INT prtExHsrRlbEnable	1.3.6.1.4.1.164.3.2.3.2.10.1.1.17	INTEGER	read-write	Enable/Disable RLB.
INT prtExHsrRtsDtr	1.3.6.1.4.1.164.3.2.3.2.10.1.1.15	INTEGER	read-write	RTS & DTR.
INT prtExHsrSltIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted.
INT prtExHsrStopBits	1.3.6.1.4.1.164.3.2.3.2.10.1.1.9	INTEGER	read-write	This object indicates the minimum number of stop bits in the tx async frame. This object is applicable for Async protocol only.
INT prtExLs2ClkMode	1.3.6.1.4.1.164.3.2.3.2.4.1.1.6	INTEGER	read-write	This attribute indicates a unique port operation clock mode.
INT prtExLs2Connect	1.3.6.1.4.1.164.3.2.3.2.4.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs2Cts	1.3.6.1.4.1.164.3.2.3.2.4.1.1.7	INTEGER	read-write	CTS.
INT prtExLs2Dcd	1.3.6.1.4.1.164.3.2.3.2.4.1.1.8	INTEGER	read-write	DCD.
INT prtExLs2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.3	INTEGER	read-only	This attribute indicates a unique port index. For the Ls2/X.58 exPrt(7)..exPrt(10) are not valid.
INT prtExLs2Rate	1.3.6.1.4.1.164.3.2.3.2.4.1.1.5	INTEGER	read-write	Port rates.
INT prtExLs2SltIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtExLs6ClkMode	1.3.6.1.4.1.164.3.2.3.2.13.1.1.7	INTEGER	read-write	This attribute indicates a unique port operation clock mode. It is applicable for Sync protocol only .
INT prtExLs6Connect	1.3.6.1.4.1.164.3.2.3.2.13.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs6CtrlSignal	1.3.6.1.4.1.164.3.2.3.2.13.1.1.8	INTEGER	read-write	Control Signal.
INT prtExLs6Cts	1.3.6.1.4.1.164.3.2.3.2.13.1.1.10	INTEGER	read-write	This object indicates the CTS control line operation mode.
INT prtExLs6DataBits	1.3.6.1.4.1.164.3.2.3.2.13.1.1.9	INTEGER	read-write	Data Bits. This object is applicable for Async protocol only.
INT prtExLs6LinkToInternal	1.3.6.1.4.1.164.3.2.3.2.13.1.1.11	INTEGER	read-write	This object indicates which internal port of the card, the external port is linked to.
INT prtExLs6Protocol	1.3.6.1.4.1.164.3.2.3.2.13.1.1.5	INTEGER	read-write	This attribute indicates the protocol. async - can be selected only for ports 1-2.
INT prtExLs6PrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.3	INTEGER	read-only	This attribute indicates a unique port index.
INT prtExLs6Rate	1.3.6.1.4.1.164.3.2.3.2.13.1.1.6	INTEGER	read-write	Port rates in bps. g1 - contains the values : (2)-(6),(9),(12),(16) g2 - contains the values : (7),(10),(14),(19) g3 - contains the values : (8),(11),(13),(15),(17),(18),(20); it is not applicable when using Async protocol. Rates of pair ports (1-2, 3-4, 5-6) must be from the same group.
INT prtExLs6SltIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExLs6VConnect	1.3.6.1.4.1.164.3.2.3.2.13.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExLs6VEchoCanceler	1.3.6.1.4.1.164.3.2.3.2.13.2.1.6	INTEGER	read-write	Echo canceler activation.
INT prtExLs6VIfType	1.3.6.1.4.1.164.3.2.3.2.13.2.1.7	INTEGER	read-write	This attribute indicates the interface type of the port. w4wire - is applicable only for E&M port type.
INT prtExLs6VOos	1.3.6.1.4.1.164.3.2.3.2.13.2.1.10	INTEGER	read-write	Out of Service signaling mode.
INT prtExLs6VPrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExLs6VRate	1.3.6.1.4.1.164.3.2.3.2.13.2.1.5	INTEGER	read-write	Rate (bps) used for FAX transmission and Voice coding.
INT prtExLs6VSltIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExMbeLan	1.3.6.1.4.1.164.3.2.3.2.11.1.1.4	INTEGER	read-write	This attribute indicates whether the MBE port is operated as main or remote bridge.
INT prtExMbePrtIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtExMbeSltIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtExPh1MlClkMode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.13	INTEGER	read-write	Defines the clock operation mode of the T1/E1 interface. Ports that are connected to the TDM Buses must be in nodalTiming(3) clock mode.
INT prtExPh1MlConnect	1.3.6.1.4.1.164.3.2.3.2.2.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the card considerations because it may indicate that the module has only one physical interface.
INT prtExPh1MlFdlType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.16	INTEGER	read-write	A unique number to identify the side of the FDL operation. Normal: 'response' for the user side and 'command' for the PTT side. Applicable only when working with ESF-T1 link
INT prtExPh1MlIfType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.24	INTEGER	read-write	Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values.
INT prtExPh1MlImpedance	1.3.6.1.4.1.164.3.2.3.2.2.1.1.27	INTEGER	read-write	The Line Impedance. For T1 (always balanced), impedance is 100 ohm. For E1: - balanced = 120 ohm - unbalanced = 75 ohm.
INT prtExPh1MlInbandMng	1.3.6.1.4.1.164.3.2.3.2.2.1.1.17	INTEGER	read-write	A unique number to identify an Inband management over the link.
INT prtExPh1MlInbandMngRate	1.3.6.1.4.1.164.3.2.3.2.2.1.1.18	INTEGER	read-write	A unique number to identify the rate of the Inband management (Kbps). E1 port - it is not applicable when prtExPh1MlInbandMng selected is off. T1 port - it is not applicable when prtExPh1MlInbandMng selected is off OR fdlOrTs0.
INT prtExPh1MlInbandMngRoutProt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.23	INTEGER	read-write	This attribute indicates the Inband Mng routing protocol of the port.
INT prtExPh1MlInternalSwitch	1.3.6.1.4.1.164.3.2.3.2.2.1.1.30	INTEGER	read-write	This parameter shows whether the data will be transferred from one port to the other port within the same group of 2 ports. The default value is: Enable. Disable value might be necessary for security implementations or for ring applications. For Vmux-2100 device this parameter is used on the Channelized Cards. Both ports in each group should have the same value for this parameter.
INT prtExPh1MlLineCode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.6	INTEGER	read-write	This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for MPH.1/T1 E1 line code parameters for MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExPh1MlLineLen	1.3.6.1.4.1.164.3.2.3.2.2.1.1.7	INTEGER	read-write	This attribute is the line length parameter used only for T1/DSU interfaces. lenXXXpXXXft = len-XXX-XXXft.
INT prtExPh1MlLineType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.5	INTEGER	read-write	This attribute is the line type parameter for T1/E1 interface. The user should select only the values which are relevant to the specific port: (2),(3), (8) - for T1 port (4)..(7), (9) - for E1 port. (101) framed - This value does not exist in standard MIB and is used for a non-standard E1 port that doesn't has real framer. Note: for old devices, g732unframed(8) was used as E1 Unframed. That was because at the time this value did not exist in the standard MIB (RFC-1406), so we added it in private MIB. Now that it was added to standard MIB, private MIB was updated as well. This parameter has the same values as dsx1LineType in DS1 MIB (RFC-3895). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7) g732unframed dsx1Unframed (8) --from RFC-3895 e1Unframed dsx1E1Unframed (9) --from RFC-3895
INT prtExPh1MlMfClkSrcPrt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.15	INTEGER	read-write	A unique number to identify a port position in the mux. It has no effect when the prtExPh1MlMfClkSrcSlt selected is Local. inPrt1 - for MTML-H/E1 cards.
INT prtExPh1MlMfClkSrcSlt	1.3.6.1.4.1.164.3.2.3.2.2.1.1.14	INTEGER	read-write	This attribute indicates whether the port Tx multiframe is synchronized with Rx multiframe of another port and the slot position of that port. This operation is required in order to bypass signaling of PCM voice channels. Its value is always local(2) when the port isn't connected to any TDM bus. When it's value is local(2) there is no meaning to 'prtExPh1MlMfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPh1MlMultiplier	1.3.6.1.4.1.164.3.2.3.2.2.1.1.25	INTEGER	read-write	The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps.
INT prtExPh1MlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.3	INTEGER	read-only	This attribute indicates a unique port number. MP-2100/2200: MTML-1/E1 and MTML-1/T1 cards have only one external interface. inPrt1, inPrt2 - for MTML-H/2E1 and HSH cards. inPrt1..inPrt4 - for MTML-E2 and MSL-4 cards. exPrt2..exPrt4 - for MTML-4 cards and others exPrt1..exPrt8 - for ML-8 cards. inPrt1..inPrt8 - for MSL-8 and VF-30 card family. MP-104/204: only exPrt3 (3) is applicable. MP-4100: intPrt1...intPrt84 - for CLX cards. For other products' index see their specification.
INT prtExPh1MlQ50BwControl	1.3.6.1.4.1.164.3.2.3.2.2.1.1.28	INTEGER	read-write	This object enables configuration of Q.50 Bandwidth Control on the port. If the bandwidth exceeds a certain threshold it is possible to disable new calls in the PBX via Q.50 protocol. Q.50 supports only E1 ports with Line Types: E1-MF (G.732S), E1-CRC-MF(G.732SCRC ) It does not support T1 ports. Annex A - the basic type of Q.50 which focuses only on the bandwidth control. Can use one of the following pairs of signaling bits: A&B or C&D. Annex B - Expansion of Annex A which includes also call release messages and Maintenance Messages. Uses A&B bits only.
INT prtExPh1MlQ50SignalPair	1.3.6.1.4.1.164.3.2.3.2.2.1.1.29	INTEGER	read-write	Q.50 Signaling bits Pair that is currently in use: A&B bits or C&D bits. For Annex B it will always be: aAndB (2).
INT prtExPh1MlRedundPort	1.3.6.1.4.1.164.3.2.3.2.2.1.1.21	INTEGER	read-write	This object indicates the redundacy ML port, coupled with the current ML port (prtExPh1MlPrtIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. When value is not 'none', it should be mutual to the redundant ML port. inPrt1 - for MTML-H/E1 cards. inPrt1..inPrt4 - for MTML-E2 cards. exPrt2..exPrt4 - for MTML-4 cards.
INT prtExPh1MlRedundSlot	1.3.6.1.4.1.164.3.2.3.2.2.1.1.20	INTEGER	read-write	This object indicates the slot containing the redundacy ML card, coupled with the current ML (prtExPh1MlSltIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. In the ?004 Unit the entries io6(10)..io12(16) are not valid When value is not 'none', it should be mutual to the redundant ML slot.
INT prtExPh1MlRedundType	1.3.6.1.4.1.164.3.2.3.2.2.1.1.19	INTEGER	read-write	This object determines the ML redundancy type: none - no ML redundacy dualCableAIS - each ML card is connected by a separate dualCableParallelTx cable to the other MUX (two cables connect two MUXes). There are two types of dual redundancy. yCable - Y cable is connected to both ML cards (one cable connects two MUXes). Default=none When only one ML card exists, the type can be only 'none'. The value should be the same for both ML slots.
INT prtExPh1MlRestoreTime	1.3.6.1.4.1.164.3.2.3.2.2.1.1.8	INTEGER	read-write	The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface.
INT prtExPh1MlRxSensitivity	1.3.6.1.4.1.164.3.2.3.2.2.1.1.10	INTEGER	read-write	This attribute is the rx line sensitivity parameter. low26dBm, high36dBm - applicable for T1-CSU shortHaul, longHaul - applicable for MTML-4 cards low15dbm was added for vmux110/210 T1 ports.
INT prtExPh1MlSigService	1.3.6.1.4.1.164.3.2.3.2.2.1.1.31	INTEGER	read-write	Signaling Service given by this link. notApplicable - for T1 links normal - usual Signaling advanced - V5 Signaling.
INT prtExPh1MlSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used.
INT prtExPh1MlTdmTrunk	1.3.6.1.4.1.164.3.2.3.2.2.1.1.12	INTEGER	read-write	This attribute indicates whether the port is used to transfer TDM cards data and through which Bus.
INT prtExPh1MlTsByteReversal	1.3.6.1.4.1.164.3.2.3.2.2.2.1.16	INTEGER	read-write	Byte Reversal. This variable defines whether the LSB or MSB is transmitted first. no(2) - MSB is transmitted first yes(3) - LSB is transmitted first.
INT prtExPh1MlTsChRate	1.3.6.1.4.1.164.3.2.3.2.2.2.1.15	INTEGER	read-write	The Rate of the Signaling Channel. notApplicable(1) when TS Type is other than Signaling or Transparent
INT prtExPh1MlTsIConSlot	1.3.6.1.4.1.164.3.2.3.2.2.2.1.5	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS).
INT prtExPh1MlTsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.3	INTEGER	read-only	This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have only one external interface. exPrt2 - for ME1-2, MT1-2 and mhsPri cards. exPrt3, exPrt4 - for mhsPri cards. inPrt1 - for MTML-H/E1 cards.
INT prtExPh1MlTsSigProfile	1.3.6.1.4.1.164.3.2.3.2.2.2.1.17	INTEGER	read-write	This object indicates the Signaling Profile of the port. It is applicable only when prtMl4SigProfile=perTS. p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5
INT prtExPh1MlTsSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (255) is used.
INT prtExPh1MlTsSubChType	1.3.6.1.4.1.164.3.2.3.2.2.2.1.13	INTEGER	read-write	The Time Slot Sub-Channel Type. This variable is relevant only when Time-Slot Type is SubCh (e.g. prtExPh1MlTsType = subCh1...subCh8).
INT prtExPh1MlTsTest	1.3.6.1.4.1.164.3.2.3.2.2.2.1.9	INTEGER	read-write	This attribute indicates a test to be activated on the selected TS. It is applicable only when prtSTstCmd=testPerTS(31). notApplicable - when prtSTstCmd is NOT testPerTS(31). none - no test is applied for the selected TS. split - when the tests are per Bit of the selected TS.
INT prtExPh1MlTsType	1.3.6.1.4.1.164.3.2.3.2.2.2.1.10	INTEGER	read-write	The Time Slot Type. Transparent - means that the Time Slot will be Rx/Tx as is without processing it. If the device requires more than 1 unique data or ss7 Time Slot, options with numbers can be used like: data...data4. Each numbered Type can go to a different destination. ss7n2 - means the 2nd group of ss7 Time Slots. data2,data3, data4 mean group 2,3,4 of Data Time Slots. subCh1...subCh8 mean Sub Channel 1...8, respectively. trau, qmux, dynamic, signaling - are used by GSM devices.
INT prtExPh1MlTxGain	1.3.6.1.4.1.164.3.2.3.2.2.1.1.9	INTEGER	read-write	This attribute is the tx gain parameter used only for T1/CSU interfaces.
INT prtExPhPlCcittCrc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.32	INTEGER	read-write	This object indicates how many Bits are used for CRC (HDLC item).
INT prtExPhPlClkMode	1.3.6.1.4.1.164.3.2.3.2.3.1.1.9	INTEGER	read-write	Clock mode.
INT prtExPhPlCllmMsg	1.3.6.1.4.1.164.3.2.3.2.3.1.1.28	INTEGER	read-write	This object is CLLM Message (if required or not). It determines whether to send (or not) a congestion message when the port is Rx congested. Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlClockEncoding	1.3.6.1.4.1.164.3.2.3.2.3.1.1.30	INTEGER	read-write	This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols. For MAXCESS 3000 & MP2100H: when setting to nrzI (3) the nrzI works as nrzI Mark. For MAXCESS 30/300 when setting to nrzI (3) the nrzI works as nrzI Space.
INT prtExPhPlCongResponse	1.3.6.1.4.1.164.3.2.3.2.3.1.1.11	INTEGER	read-write	This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/received becn to/from the network). no - do nothing flowControl - translates the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done on both directions. toFlowControl- translates the backward congestion indication received from the internal connection port (normally the network side) to flow control and do nothing in the other direction.
INT prtExPhPlConnect	1.3.6.1.4.1.164.3.2.3.2.3.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExPhPlConnectionTyp	1.3.6.1.4.1.164.3.2.3.2.3.1.1.8	INTEGER	read-write	This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management opration (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetMotMana - indicates network internal line, but the remote mux is not managed by the NMS. User - User to Network Interface. OtherNet - Network To Network Interface. PubNet - Access Mux To PubNet Interface.
INT prtExPhPlDataBits	1.3.6.1.4.1.164.3.2.3.2.3.1.1.17	INTEGER	read-write	This attribute indicates the number of data bits in async frame. It is relevant only for Async protocols.
INT prtExPhPlDcdRts	1.3.6.1.4.1.164.3.2.3.2.3.1.1.15	INTEGER	read-write	Protocol may require end to end connect indication over the network. End to end link connection establishment over the FR network will be indicated to the user by using DCD or RTS control signals, depending on the clock mode: DCE or DTE respectively. The options are : - On : DCD(DCE)/RTS(DTE) will be constantly ON no matter if the End to End connection is established or not. - End to End: The DCD(DCE)/RTS(DTE) will be according to the status of the End to End connection.
INT prtExPhPlDcdRtsControlPath	1.3.6.1.4.1.164.3.2.3.2.3.1.1.16	INTEGER	read-write	Protocol may require end to end connect indication over the network. This parameter defines whether to take the user connection status (RTS(DCE)/DCD(DTE)) and forward it to the network side. - on : Transmit active connection to the network regardless the RTS/DCD control lines status. - off: Transmit active connection to the network according to the status of the RTS/DCD pin.
INT prtExPhPlDceClkSrc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.10	INTEGER	read-write	This attribute indicates the source of the clock when working in dce or ext-dce clock mode. notApplicable(1) - is applied for dte(3) and lbt(5) clock modes. When clock mode is dte, the clock source is always external, therefore this object's value is notApplicable. local(2) and nodalTiming(3) - are valid in dce(1), extDce(2) or int(4) clock modes. The recommended clock source is local(2).
INT prtExPhPlDlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.3.2.1.7	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to. clNMS - will be used for NMS SNMP messages. It can be any port of the CL card. This value will be selectable only if prtExPhPlDlciIConSlt='cl' or 'notApplicable'.
INT prtExPhPlDlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.3.2.1.6	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. cl - will represent any of the CL slots. This value can be selected for multiple DLCIs of the product. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPhPlDlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. PH.1/E1 and PH.1/T1 cards have three internal ports. Stand-alone units may have six such ports.
INT prtExPhPlDlciRxBc	1.3.6.1.4.1.164.3.2.3.2.3.2.1.11	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line).
INT prtExPhPlDlciRxBe	1.3.6.1.4.1.164.3.2.3.2.3.2.1.12	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line).
INT prtExPhPlDlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPhPlDlciStatus	1.3.6.1.4.1.164.3.2.3.2.3.2.1.14	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
INT prtExPhPlDlciTxBc	1.3.6.1.4.1.164.3.2.3.2.3.2.1.9	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line).
INT prtExPhPlDlciTxBe	1.3.6.1.4.1.164.3.2.3.2.3.2.1.10	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line).
INT prtExPhPlDlciValid	1.3.6.1.4.1.164.3.2.3.2.3.2.1.5	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
INT prtExPhPlFlowControl	1.3.6.1.4.1.164.3.2.3.2.3.1.1.14	INTEGER	read-write	This attribute indicates the required flow control betweeen the port and the remote equipment. fecnBecn - is valid only for FR, FR+ and CR protocols. xonXoff,dtrCts - are valid only for Async protocols. speedReduction - is valid only for DLC protocol when the Clock Mode is DCE and the Clock Source is Local.
INT prtExPhPlFrameSeparator	1.3.6.1.4.1.164.3.2.3.2.3.1.1.33	INTEGER	read-write	This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line.
INT prtExPhPlFrMngProt	1.3.6.1.4.1.164.3.2.3.2.3.1.1.22	INTEGER	read-write	This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtExPhPlConnectionTyp = sameNetManaged, this object will be RO (internally determined).
INT prtExPhPlHRate	1.3.6.1.4.1.164.3.2.3.2.3.1.1.5	INTEGER	read-write	This attribute indicates the port speed for HIGH speed cards. The card has limitations about the maximum sigma channel speeds and about the possible rates for each clock mode . N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. 'r9d6KbpsNLE' means rate of 9.6 Kbps ('d'=dot). Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r2048KbpsE (63), -- r2048KbpsNLE
INT prtExPhPlLRate	1.3.6.1.4.1.164.3.2.3.2.3.1.1.6	INTEGER	read-write	This attribute indicates the port speed for LOW speed cards. The card has limitations about the possible rates for each clock mode. N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r57600bpsLE (16), -- r57600bpsNLE
INT prtExPhPlModemActivate	1.3.6.1.4.1.164.3.2.3.2.3.3.1.5	INTEGER	read-write	This object indicates whether the Dial Up Modem is activated when the first frame is received or it is always activated. Default: onFirstFrame
INT prtExPhPlModemPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.3	INTEGER	read-only	This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid.
INT prtExPhPlModemSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtExPhPlModemStatus	1.3.6.1.4.1.164.3.2.3.2.3.3.1.4	INTEGER	read-write	This object indicates whether a Dial Up Modem is enabled on this port. Default: disable For Vmux devices this object shows whether there is Modem Relay support.
INT prtExPhPlParity	1.3.6.1.4.1.164.3.2.3.2.3.1.1.18	INTEGER	read-write	This attribute indicates the parity operation mode in async frame. It is relevant only for Async protocols.
INT prtExPhPlProtDelayLevel	1.3.6.1.4.1.164.3.2.3.2.3.1.1.29	INTEGER	read-write	This object is the Segmentation in Bytes. In some cases, the enumerated values will mean other segmentation values than specified: Product: MX-3000 MX-3000 MX-300/MX-30 Protocol: FR+ Transparent FR+ ----------------------------------------------------- level 1 50 Bytes 44 Bytes 50 Bytes level 2 158 Bytes 155 Bytes 158 Bytes level 3 266 Bytes 266 Bytes 266 Bytes level 4 376 Bytes 377 Bytes 376 Bytes level 5 484 Bytes 488 Bytes 484 Bytes Defval=level 1 value This parameter is applicable only for FR+ and transparent protocols.
INT prtExPhPlProtocol	1.3.6.1.4.1.164.3.2.3.2.3.1.1.7	INTEGER	read-write	This object indicates the applied protocol.
INT prtExPhPlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.3	INTEGER	read-only	This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid.
INT prtExPhPlPvcCreateMsg	1.3.6.1.4.1.164.3.2.3.2.3.1.1.27	INTEGER	read-write	This object is Update Message (if required or not). It determines whether a message of a New PVC Creation is requested or not (yes/no). Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
INT prtExPhPlSltIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtExPhPlStopBits	1.3.6.1.4.1.164.3.2.3.2.3.1.1.19	INTEGER	read-write	This attribute indicates the minimum number of stop bits in the tx async frame. It is relevant only for Async protocols.
INT prtExPhPlTc	1.3.6.1.4.1.164.3.2.3.2.3.1.1.13	INTEGER	read-write	This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports of a specific card .
INT prtExPVc4AutoFaxMode	1.3.6.1.4.1.164.3.2.3.2.9.1.1.21	INTEGER	read-write	This object indicates if the system will switch automatically to FAX mode when detecting FAX activity. Default=Yes.
INT prtExPVc4CoderAndRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.33	INTEGER	read-write	Coder and Rate for the Voice Compression. In MPH: Relevant for MVC-8 card only.
INT prtExPVc4CodingLaw	1.3.6.1.4.1.164.3.2.3.2.9.1.1.29	INTEGER	read-write	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations
INT prtExPVc4Connect	1.3.6.1.4.1.164.3.2.3.2.9.1.1.5	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExPVc4DlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.9.2.1.6	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to.
INT prtExPVc4DlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.9.2.1.5	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPVc4DlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. VC4 cards have four external ports.
INT prtExPVc4DlciRxBc	1.3.6.1.4.1.164.3.2.3.2.9.2.1.10	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line).
INT prtExPVc4DlciRxBe	1.3.6.1.4.1.164.3.2.3.2.9.2.1.11	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line).
INT prtExPVc4DlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtExPVc4DlciStatus	1.3.6.1.4.1.164.3.2.3.2.9.2.1.13	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
INT prtExPVc4DlciTxBc	1.3.6.1.4.1.164.3.2.3.2.9.2.1.8	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line).
INT prtExPVc4DlciTxBe	1.3.6.1.4.1.164.3.2.3.2.9.2.1.9	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line).
INT prtExPVc4DlciValid	1.3.6.1.4.1.164.3.2.3.2.9.2.1.4	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
INT prtExPVc4DtmfRelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.35	INTEGER	read-write	When DTMF RELAY is disabled, the DTMF digits (dialed by the user) are transmitted as compressed voice and in the remote unit are decompressed. When DTMF RELAY is enabled, the DTMF digits are detected at the near side and not transmitted as voice. Instead, only an indication of what digits were dialed are transmitted and in the far end the tone is regenerated.
INT prtExPVc4DynamicJitter	1.3.6.1.4.1.164.3.2.3.2.9.1.1.37	INTEGER	read-write	The MVC8 uses two mechanisms to overcome the network delay. The first one is a static jitter buffer which holds a constant buffer of up to 300 Msec and can be controled by the JITTER parameter (prtExPVc4VarDelay). The second one is the dynamic jitter which calculates, in real time, the network delay and handles a jitter buffer dynamically. The dynamic mechanism that is implemented in MVC8, was intended to overcome network delay yet when the network bursts, the MVC8 dynamic mechanism is not able to overcome the delay. Therefore it is better not to use the dynamic jitter (DISABLE - should be the default) where bursts may occur often.
INT prtExPVc4EandMType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.38	INTEGER	read-write	This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters.
INT prtExPVc4EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.9.1.1.12	INTEGER	read-write	Echo canceler activation.
INT prtExPVc4ExtensionType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.16	INTEGER	read-write	This object indicates the type of extension relevant for this port. ipForceConnect (6) is used for automatic connection or automatic dialing when the phone is off hook (hot line). permanentDial (7) means that the call is established upon power up. The hook may be on or off. Permanent Dialing can be used when there is no signaling. autoAccept (8) means that the called party in the Permanent Dialing will accept the call from the remote side automatically upon on or off hook.
INT prtExPVc4FaxRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.22	INTEGER	read-write	FAX initial rate. Default=9600 bps.
INT prtExPVc4GenerateRingBack	1.3.6.1.4.1.164.3.2.3.2.9.1.1.30	INTEGER	read-write	Determines whether the Ring Back tone is generated locally or from the remote end. The default is - NO (Meaning coming from the remote end). Yes means that the Ring Back Tone is generated locally. Applicable only for Force Connect.
INT prtExPVc4GenerateTone	1.3.6.1.4.1.164.3.2.3.2.9.1.1.28	INTEGER	read-write	This parameter indicates whether the device (MX or MPH) should generate dial tones for the channel. If the value is yes (3), it generates dial tones. If the value is no (2), the connected equipment will generate dial tones. For example for some ISDN sets the dial tone is generated by the phone itself while for others sets it is generated by the MX.
INT prtExPVc4HuntGroupMb	1.3.6.1.4.1.164.3.2.3.2.9.1.1.19	INTEGER	read-write	This object indicates if this port belongs to an hunt group.
INT prtExPVc4IfType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.6	INTEGER	read-write	This attribute indicates the interface type of the port. eAndM4wires and eAndM2wires - are valid only for E&M port type eAndM4wires - means 2/4 wires fxoGnd and fxoLoop - are valid only for FXO port type fxsGnd and fxsLoop - are valid only for FXS port type e1Framer, e1Slave, t1Framer, t1Slave - are applicable for the mvc4Pbx cards only.
INT prtExPVc4MaxRate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.9	INTEGER	read-write	Voice rate.
INT prtExPVc4MultiFreqRelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.43	INTEGER	read-write	This object enables/disables Multi Frequency Signaling Detection.
INT prtExPVc4Oos	1.3.6.1.4.1.164.3.2.3.2.9.1.1.11	INTEGER	read-write	Handling type, when connection is lost.
INT prtExPVc4OutPulsing	1.3.6.1.4.1.164.3.2.3.2.9.1.1.18	INTEGER	read-write	This field indicates whether to outpulse the received digits. It is notApplicable(1) when the extension type is forceConnect(2).
INT prtExPVc4PortConnection	1.3.6.1.4.1.164.3.2.3.2.9.1.1.32	INTEGER	read-write	Port connection determines whether the port is connected to a PABX (Trunk) or to Telephone set (Line) . It determines whether to send certain messages to the port or not. If the type is LINE then the port generates a ring back tone , if TRUNK it doesn't (The PBX does it).
INT prtExPVc4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.3	INTEGER	read-only	This object indicates the port number in the selected card (slot).
INT prtExPVc4PrtType	1.3.6.1.4.1.164.3.2.3.2.9.1.1.4	INTEGER	read-write	This object indicates the type of the selected port. In Mx 30/300 phase 4: s0 & u are for Voice over ISDN. In MX 30/300 phase 5: sQsig & uQsig are used for Voice over ISDN with Qsig option. In MX MVC4 voice cards, each pair of ports 1-2, 3-4 may have a different type: E&M, FXO, FXS. In MVC4 compressed voice cards ports 1..4 have the same interface for all ports. In MVC8 compressed voice cards each group of ports 1..4, 5..8 may have a different type: E&M, FXO, FXS.
INT prtExPVc4SeizeAck	1.3.6.1.4.1.164.3.2.3.2.9.1.1.23	INTEGER	read-write	This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Example: If Seize Ack Parameter = YES, when the MVC.4 receives a seize signal (Off Hook) from the PBX it will send an Off Hook to the PBX. The Seize Parameter is relevant for all the following cards: MVC-4 MVC-4/E1-Framer MVC-4/T1-DSU-Framer MVC-4/T1-CSU-Framer MVC-4/E1-SLAVE MVC-4/T1-SLAVE Default values: Analog FXS - No (value can't be changed). Analog FXO - Yes (value can't be changed). Analog E&M - No (values NO/YES). Digital E1/T1 Framer & Slave - No.
INT prtExPVc4SignalingProtocol	1.3.6.1.4.1.164.3.2.3.2.9.1.1.24	INTEGER	read-write	The signaling protocol that will be used between the PABX & the voice port. Delay Start Protocol: the line is seized by sending an Off hook signal and after a delay, if the called party is available (On hook) DTMF (Dual Tone Multi Frequency) digits are sent towards the called party. Immediate Start Protocol: the line is seized by sending an Off Hook signal and immediately DTMF digits are sent towards the called party. Wink start protocol: the line is seized by sending an Off Hook signal and then the called party sends a short Off Hook wink signal. Now the calling party starts sending DTMF digits.
INT prtExPVc4SltIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
INT prtExPVc4SuperTandem	1.3.6.1.4.1.164.3.2.3.2.9.1.1.46	INTEGER	read-write	The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem, when enabled, allows transmission of compressed voice between a few devices and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay.
INT prtExPVc4Tc	1.3.6.1.4.1.164.3.2.3.2.9.1.1.10	INTEGER	read-write	Time interval for CIR control, in seconds. The value will be the same for all cards' ports.
INT prtExPVc4TransportProtocol	1.3.6.1.4.1.164.3.2.3.2.9.1.1.42	INTEGER	read-write	Transport Protocol. ptp = point to point. aal2oMpls = AAL2 over MPLS.
INT prtExPVc4Wire	1.3.6.1.4.1.164.3.2.3.2.9.1.1.15	INTEGER	read-write	This object indicates the wiring of the E&M port. It is applicable only for E&M card type.
INT prtExTreLan	1.3.6.1.4.1.164.3.2.3.2.12.1.1.4	INTEGER	read-write	This attribute indicates whether the TRE port is operated as main or remote bridge. Default=remote.
INT prtExTreLanRate	1.3.6.1.4.1.164.3.2.3.2.12.1.1.5	INTEGER	read-write	This attribute indicates the Rate of the TRE port in Mbit/sec. Default-r4M.
INT prtExTrePrtIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtExTreSltIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtExTsBitTest	1.3.6.1.4.1.164.3.1.4.2.1.1.8	INTEGER	read-write	This attribute indicates a test to be activated on the selected Bit. It is applicable only when prtExPh1MlTsTest=split(254). none - no test is applied for the selected Bit. notApplicable - when prtExPh1MlTsTest is NOT split(254).
INT prtExTsIConSlot	1.3.6.1.4.1.164.3.1.4.2.1.1.6	INTEGER	read-write	This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units.
INT prtExTsSltIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units.
INT prtExVc2BusProtectionPoint	1.3.6.1.4.1.164.3.2.3.2.5.1.39	INTEGER	read-write	This object defines if the port is Bus Protection Point or not. notApplicable - when prtExVc2DspMode=pointToPoint. When we have a chain of devices where the edge devices ports are the Bus Protection Point, user must configure one of these ports as 'first' and the other as 'last'. It does not matter which one, it just matters that they will be different.
INT prtExVc2CallEnable	1.3.6.1.4.1.164.3.2.3.2.5.1.14	INTEGER	read-write	This object indicates the Enabled Call direction. notApplicable - for all cards except VC-2/R2. both - incoming + outgoing.
INT prtExVc2CallerIdEnable	1.3.6.1.4.1.164.3.2.3.2.5.1.33	INTEGER	read-write	This object Enables/Disables Receiving the Caller Id number from the remote side, for this port/channel.
INT prtExVc2CasStd	1.3.6.1.4.1.164.3.2.3.2.5.1.16	INTEGER	read-write	This object indicates the CAS (Channel Associated Signaling) Standard. notApplicable - for all cards except VC-2/R2.
INT prtExVc2CodingLaw	1.3.6.1.4.1.164.3.2.3.2.5.1.8	INTEGER	read-write	This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations
INT prtExVc2CompressMethod	1.3.6.1.4.1.164.3.2.3.2.5.1.34	INTEGER	read-write	This object is applicable only when prtExVc2Encoding=adpcm. It defines which method is used for Compression. g726 - for 4 bits (the standard method). g726 - for 3 bits. It is especially needed for T1 applications with signaling.
INT prtExVc2Connect	1.3.6.1.4.1.164.3.2.3.2.5.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExVc2ConvTime	1.3.6.1.4.1.164.3.2.3.2.5.1.27	INTEGER	read-write	Conversation Time in minutes. Applicable for VC-6A/4LB card.
INT prtExVc2EandMType	1.3.6.1.4.1.164.3.2.3.2.5.1.25	INTEGER	read-write	This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters.
INT prtExVc2EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.5.1.17	INTEGER	read-write	Echo canceler activation. notApplicable - for VC-2 and VC-6 cards.
INT prtExVc2EchoCancelerModule	1.3.6.1.4.1.164.3.2.3.2.5.1.29	INTEGER	read-only	This parameter indicates whether Echo canceler module exists for this port.
INT prtExVc2Encoding	1.3.6.1.4.1.164.3.2.3.2.5.1.19	INTEGER	read-write	Voice Encoding Mode. linear - is relevant only for the ports of VC-16A card.
INT prtExVc2IfSignaling	1.3.6.1.4.1.164.3.2.3.2.5.1.23	INTEGER	read-write	This entry is applicable only for VC-6A, VC-6AG, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS cards. Interface Analog Signaling. Must be the same for all card's ports. loopStart - for the usual trunk/phone types. groundStart - for trunks that need Ground signaling . winkStart - for trunks that need Reverse Polarity.
INT prtExVc2IfType	1.3.6.1.4.1.164.3.2.3.2.5.1.18	INTEGER	read-write	Interface Type.
INT prtExVc2ImpedanceStandard	1.3.6.1.4.1.164.3.2.3.2.5.1.40	INTEGER	read-write	This object defines the Standard used for Impedance. -G.712 - 600 Ohm - used in USA and other countries. -Q552/ETSI - used in some countries in Europe -Q522/Italy - used in Italy.
INT prtExVc2LinkTo	1.3.6.1.4.1.164.3.2.3.2.5.1.11	INTEGER	read-write	This attribute indicates the slot of the ML card to which the VC card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExVc2MeterRate	1.3.6.1.4.1.164.3.2.3.2.5.1.22	INTEGER	read-write	This entry is applicable only for VC-6A/FXO, VC-6A/FXS, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS. Meter Rate means rate of Call Meter in Public Phones, in KHz units. For some cards, the value must be the same for all card's ports.
INT prtExVc2NoiseLevelForVAD	1.3.6.1.4.1.164.3.2.3.2.5.1.37	INTEGER	read-write	This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to deal with. notApplicable - when prtExVc2VAD=off.
INT prtExVc2ObMode	1.3.6.1.4.1.164.3.2.3.2.5.1.35	INTEGER	read-write	This object defines the Net operation mode of the Omni-Bus card's port. pointToPoint - only 2 end-point ports talk; like any other voice card omniBus - many talk and listen. Like conference call. All can listen to all. pointToMultiPointSrc - There is one Master who can be heard by all. All can talk, but only the Master can hear all. Others can hear only the Master. This port is of the Master (Src). pointToMultiPointDst - There is one Master who can be heard by all. All can talk, but only the Master can hear all. Others can hear only the Master. This port is of a Destination (NOT Master).
INT prtExVc2Oos	1.3.6.1.4.1.164.3.2.3.2.5.1.10	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
INT prtExVc2OperMode	1.3.6.1.4.1.164.3.2.3.2.5.1.12	INTEGER	read-write	This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request.
INT prtExVc2R2Delay	1.3.6.1.4.1.164.3.2.3.2.5.1.15	INTEGER	read-write	This object indicates the R2 Delay. notApplicable - for all cards except VC-2/R2.
INT prtExVc2RemType	1.3.6.1.4.1.164.3.2.3.2.5.1.26	INTEGER	read-write	Remote Type. Applicable for VC-6A/4LB card & for IPMUX-1E Far End Type - E1,T1(T1-ESF) or T1-D4 .
INT prtExVc2ReversePolarity	1.3.6.1.4.1.164.3.2.3.2.5.1.30	INTEGER	read-write	This object Enables/Disables Reverse Polarity for this port.
INT prtExVc2RingerFrequency	1.3.6.1.4.1.164.3.2.3.2.5.1.31	INTEGER	read-write	This object selects the Ringer Frequency (Hz) for this port.
INT prtExVc2SeizeAck	1.3.6.1.4.1.164.3.2.3.2.5.1.24	INTEGER	read-write	This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Default value for WR FXO: no(2).
INT prtExVc2Sig	1.3.6.1.4.1.164.3.2.3.2.5.1.9	INTEGER	read-write	This attribute indicates the method for decoding/encoding the signaling information(on/off hook). noSignaling (1) - not using signaling (only voice). robbedBitMultiFrame(2) - is the standard method for T1 links and proprietary method for E1 links. chAssociatedE1 (3) - is valid only for E1 G.732S links. robbedBitFrame (4) - is proprietary method implimenting 7 bit for the voice and 1 bit dedicated for signaling. For some cards, this object is equal for all the ports in the specific module because of HW limitations.
INT prtExVc2SigFeedback	1.3.6.1.4.1.164.3.2.3.2.5.1.28	INTEGER	read-write	Signaling Feedback. Applicable for VC-8/FXO and VC-16/FXO cards.
INT prtExVc2SigProfile	1.3.6.1.4.1.164.3.2.3.2.5.1.13	INTEGER	read-write	This object indicates the Signaling Profile of the port. notApplicable - for VC-2 family and when prtExVc2Sig=noSignaling(1) p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4
INT prtExVc2SigService	1.3.6.1.4.1.164.3.2.3.2.5.1.32	INTEGER	read-write	Signaling Service. advanced - is relevant only for ports of VC-8, VC-16 FXS cards. It is used for Signaling Services of V5.1 or R2.
INT prtExVc2VAD	1.3.6.1.4.1.164.3.2.3.2.5.1.36	INTEGER	read-write	This object defines whether Voice Activation Detector (VAD) will be On or Off. off - will be usually selected when a Modem is connected to the port; not a phone. notApplicable - when prtExVc2DspMode=pointToPoint.
INT prtExVc2WesternSigMode	1.3.6.1.4.1.164.3.2.3.2.5.1.38	INTEGER	read-write	This object defines the Western Signaling Mode. detector - detects signal and passes it as is. generator - generates the signal. notApplicable - when Western HW is not installed.
INT prtExVc2Wire	1.3.6.1.4.1.164.3.2.3.2.5.1.7	INTEGER	read-write	For some cards, this object is equal for all the ports in the specific card because of HW limitations. For FXO & FXS this parameter is not applicable.
INT prtExVc3Connect	1.3.6.1.4.1.164.3.2.3.2.14.1.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtExVc3EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.14.1.1.9	INTEGER	read-write	Echo canceler activation. The value will be the same for all the card's external ports.
INT prtExVc3PrtIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExVc3Rate	1.3.6.1.4.1.164.3.2.3.2.14.1.1.8	INTEGER	read-write	Rate in bps.
INT prtExVc3SltIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVc3Wire	1.3.6.1.4.1.164.3.2.3.2.14.1.1.7	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
INT prtExVcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.1.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtExVcPbxFrame	1.3.6.1.4.1.164.3.2.3.2.15.1.1.8	INTEGER	read-write	This object is the frame parameter for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 values for the VC-PBX/T1 card. E1 values for the VC-PBX/E1 card. notApplicable - for the VC-PBX card. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7)
INT prtExVcPbxGroup	1.3.6.1.4.1.164.3.2.3.2.15.1.1.5	INTEGER	read-only	The group object links together several VC-PBX cards, concerning compression of the same input T1/E1 link time-slots. When ports of different slots have the same group, they are linked. When ports have a different group, they are not linked. For VC-PBX/T1 and E1 cards, this object is - their own IO Slot. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVcPbxIdleCode	1.3.6.1.4.1.164.3.2.3.2.15.1.1.14	INTEGER	read-write	Determines the code for transmission in empty time slots. notApplicable - for VC-PBX card .
INT prtExVcPbxLineCode	1.3.6.1.4.1.164.3.2.3.2.15.1.1.10	INTEGER	read-write	This object is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for VC-PBX/T1 E1 line code parameters for VC-PBX/E1 notApplicable - for VC-PBX This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
INT prtExVcPbxLineLength	1.3.6.1.4.1.164.3.2.3.2.15.1.1.11	INTEGER	read-write	This object is the line length parameter. It is applicable only for the VC-PBX/T1 card. notApplicable - for the VC-PBX and VC-PBX/E1 card. lenXXXpXXXft = len-XXX-XXXft.
INT prtExVcPbxLinkTo	1.3.6.1.4.1.164.3.2.3.2.15.1.1.12	INTEGER	read-write	This object indicates the slot of the ML card to which the VC-PBX/T1, VC-PBX/E1 card Transparent TSs are mapped. notApplicable - for VC-PBX card AND for VC-PBX/T1, VC-PBX/E1 cards, when prtExVcPbxTransparent=no . In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtExVcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtExVcPbxRestoreTime	1.3.6.1.4.1.164.3.2.3.2.15.1.1.9	INTEGER	read-write	The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface. ccittE1 - is applicable only for VC-PBX/E1 card notApplicable - is applicable for VC-PBX card
INT prtExVcPbxSignalOper	1.3.6.1.4.1.164.3.2.3.2.15.1.1.13	INTEGER	read-write	This object indicates the Signaling Operation of the VC-PBX/T1, VC-PBX/E1 external port. notApplicable - for VC-PBX card normal - all 4 signaling bits are transferred. bEqA - copy the A bit into the B bit. Applicable only for VC-PBX/T1.
INT prtExVcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVcPbxTransparent	1.3.6.1.4.1.164.3.2.3.2.15.1.1.6	INTEGER	read-write	This object indicates whether the Transparent transfer of Time-Slots is required or not. Time-Slots transferred by Transparent, will not be compressed. no - applicable only for VC-PBX/T1 and VC-PBX/E1 cards yes - applicable only for VC-PBX/T1 and VC-PBX/E1 cards notApplicable - only for VC-PBX cards.
INT prtExVcPbxTsIConPrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.7	INTEGER	read-write	This attribute indicates the port to which this TS is connected. For VF-PBX cards, only inPrt1..inPrt6 ports are valid. For VF-24/30/48/60 cards: - for prtExVcPbxTsMode=transparent or voiceTransparent, the valid ports are ML ports (exPrt1.. exPrt8, inPrt1.. inPrt8) - for prtExVcPbxTsMode=compressed or compressedCcs, the valid ports are internal ports of the same card (inPrt1..inPrt8) noConnect - when prtExVcPbxTsIConSlot=noConnect.
INT prtExVcPbxTsIConSlot	1.3.6.1.4.1.164.3.2.3.2.15.4.1.6	INTEGER	read-write	For VF-PBX cards, the io1..io12 values are applicable only when prtExVcPbxTsMode=compressed. Otherwise, its value should be noConnect. For VF-24/30/48/60 cards: - when prtExVcPbxTsMode=transparent or voiceTransparent, the io1..io12 values are applicable, indicating the ML Slot this TS is connected to. - when prtExVcPbxTsMode=compressed or compressedCcs, the value will be the same as prtExVcPbxTsSltIdx, since the compression is done within the same card. - for rest of the prtExVcPbxTsMode values, the value will be: noConnect. This object indicates whether the specified compressed/transparent time slot is connected/routed internally in the Agent and to which card it is connected. For VF-PBX card, the valid selectable slots are either the current one, (prtExVcPbxTsSltIdx), or a slot containing a VF-PBX card. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtExVcPbxTsMode	1.3.6.1.4.1.164.3.2.3.2.15.4.1.5	INTEGER	read-write	This attribute indicates the usage, process and way of the specific PABX TS towards its destination: unused - the TS is not used (no processing, no destination). compressed - the TS is used, sent for compression to an internal port (for VF-PBX cards: 1..6 for of either the same card or a VF-PBX card of the same group). For VF-24/30/48/60 - 'compressed' represents 'compressed Voice' (to differentiate it from 'compressedCcs'). In this case, the TS is compressed by an internal port (1..8). transparent - the TS is used; no processing. It is sent directly for Bypass to a ML card the VF port/TS is linked to. compressedCcs - supported only by VF-24/30/48/60 cards. The TS is used; sent for compression to the CPU. mng - the TS is used for Management (this option is used when the external port is connected to another product that has to be managed via this dedicated TS. ccs1..ccs8 - supported only by VF-24/30/48/60 cards. Compressed TS that comes from a bundle of V5.1 or V5.2 PBX. ss7n1..ss7n8 - supported only by VF-24/30/48/60 cards. Compressed TS that comes from a bundle of V5.1 or V5.2 PBX. ss7n1 can work versus Vmux having prtExPh1MlTsType=ss7(6).
INT prtExVcPbxTsPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.3	INTEGER	read-only	This attribute indicates a unique port number. VCPBX/E1, VCPBX/T1, VFPBX/E1, VFPBX/T1, VF-24/T1 and VF-30 cards have only one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. VFS cards have also internal ports.
INT prtExVcPbxTsRemPrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.9	INTEGER	read-write	This attribute indicates the end-point port on the Remote unit. VF-24/T1 and VF-30/E1 cards have one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. noConnect - when prtExVcPbxTsMode=unused, transparent, voiceTransparent or mng.
INT prtExVcPbxTsSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtExVcPbxTsSourceSlot	1.3.6.1.4.1.164.3.2.3.2.15.4.1.12	INTEGER	read-write	For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Slot of the Analog Voice port we want to compress. io1..io12 values are applicable only when prtExVcPbxTsMode=compressed(voice). Otherwise, its value should be noConnect. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtFrPlusSltIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.2	INTEGER	read-only	Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
INT prtFrStatisInvIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.3	INTEGER	read-only	The Interval of 15 min. for which the following statistics counters are applicable.
INT prtFrStatisPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtFrStatisSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
INT prtGenActiveStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.5	INTEGER	read-only	This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the port is not connected according to the active config. offLine(3) indicates that the port is down (not working) due to any problem. onLine (4) indicates that the port is up (working) offLineRedundancy(5) indicates that the port is down because it is a redundant port. onLineRedundancy (6) indicates that this is a redundant port which is up and works as the active link.
INT prtGenAlrClearCmd	1.3.6.1.4.1.164.3.3.3.1.1.1.13	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the port level alarms . Upon completion, the value will automatically change to off(2). noOp - will be used by agents that do not support this feature or object.
INT prtGenAlrMaskAll	1.3.6.1.4.1.164.3.3.3.1.1.1.14	INTEGER	read-write	on(3) - will mask all the alarms of the selected port off(2)- will unmask all alarms of the selected port except the ones selected by the prtAlrMaskTable. noOp - will be used by agents that do not support this feature or object.
INT prtGenAlrStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.6	INTEGER	read-only	Indicates the alarm state at port (ch) agent level. This object will be: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT prtGenCnfgBusConnection	1.3.6.1.4.1.164.3.1.4.2.3.1.7	INTEGER	read-write	This object indicates the support of the card regarding Bus Connection. Same value for all ports of the card. partial = 2 Buses (AB) full = 4 Buses (ABCD) partial CD = 2 Buses CD Actually the support depends on the card's HW. But, since CL has to assign data on Buses even when the card is not installed, this object has to be configured. If the actual card installed will not match the value configured, an Alarm will be issued.
INT prtGenCnfgConnect	1.3.6.1.4.1.164.3.1.4.2.3.1.11	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtGenCnfgInbandMng	1.3.6.1.4.1.164.3.1.4.2.3.1.8	INTEGER	read-write	This object indicates whether Inband Management is used over the link.
INT prtGenCnfgInbandMngRoutProt	1.3.6.1.4.1.164.3.1.4.2.3.1.9	INTEGER	read-write	This object indicates the Inband Mng Routing Protocol of the port.
INT prtGenCnfgLinkToSlot	1.3.6.1.4.1.164.3.1.4.2.3.1.4	INTEGER	read-write	This attribute indicates the slot of the ML card to which the IO port is mapped.
INT prtGenCnfgProtectionMode	1.3.6.1.4.1.164.3.1.4.2.3.1.10	INTEGER	read-write	This object indicates the Protection Mode of the port. notApplicable- when Bus Protection Point=No. For VC-4/Omni card this object is supported RO.
INT prtGenCnfgSignalingType	1.3.6.1.4.1.164.3.1.4.2.3.1.12	INTEGER	read-write	This object selects the Type of Signaling used by the port.
INT prtGenCnfgSltIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted.
INT prtGenExtInt	1.3.6.1.4.1.164.3.3.3.1.1.1.3	INTEGER	read-only	This attribute describes the type of the designated port. Exteral port is a port with a physical connector. Internal port might be of two types, one is a composite port which collects data of a few external ports into a common bandwidth (usually routed trough DS1 link); the other type is internal ports which get only part of external port data (usually a few DS0's). In the Kilomux-2100, the internal(3) value is used for composite channels or sub-channels of an ISDN Ch.
INT prtGenRdnStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.16	INTEGER	read-only	This object indicates if this port is part of a redundant pair and in this case, if it is On or Off. none(1) - No redundancy or Not Applicable off (2) - the port is part of a redundant pair and it is Off from Redundancy point of view (not the port used). on (3) - the port is part of a redundant pair and it is On from Redundancy point of view (it is the port used).
INT prtGenSlt	1.3.6.1.4.1.164.3.3.3.1.1.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. The Kilomux should use the enumerated starting with kmx.
INT prtGenTestIdx	1.3.6.1.4.1.164.3.3.3.1.2.1.2	INTEGER	read-only	This attribute indicates the test, the duration refers.
INT prtGenTestStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.7	INTEGER	read-only	This attribute will be on(3) when there is at least one test in progress (running) on the port; otherwise the value will be off(2).
INT prtGenTsType	1.3.6.1.4.1.164.3.3.3.1.3.1.4	INTEGER	read-write	The type of Timeslot. If the source or destination port is an HS port,'TS Type' must be 'data'. nc - means that this TimeSlot is not connected. voice, data, vcMP - also mean that this TS is connected. mng - means that this TS is dedicated to Management (not connected to another port.
INT prtGenType	1.3.6.1.4.1.164.3.3.3.1.1.1.11	INTEGER	read-only	This object describes the type of the selected port. idsl - applicable for external ports of HS-U cards (of DXC) when interface is LT-1.
INT prtHdslLinkType	1.3.6.1.4.1.164.3.3.3.7.1.1.5	INTEGER	read-only	The Link Type. msdsl2w - MSDSL 2 Wire hdsl2w - HDSL 2 Wire hdsl4w - HDSL 4 Wire gDsl - G.DSL
INT prtHdslMaxRate	1.3.6.1.4.1.164.3.3.3.7.1.1.4	INTEGER	read-write	Maximum Rate of the xDSL Line, in Kbps units. This object can be Set only for a Central unit.
INT prtHdslMode	1.3.6.1.4.1.164.3.3.3.7.1.1.2	INTEGER	read-write	This object indicates the HDSL mode.
INT prtHdslRptrType	1.3.6.1.4.1.164.3.3.3.7.1.1.3	INTEGER	read-only	The Repeater between Near and Far modem. none - no repeater exists between the modems hrpt - HRPT repeater exists between the modems.
INT prtHSBertCountClr	1.3.6.1.4.1.164.3.3.3.3.2.1.3	INTEGER	read-write	Setting this object (to on) initiate bert counter clear operation. Valid only when bert test is active on the specific port. (Every time a new bert test starts, the counter is automatically cleared; this command enables clearing the counter while the test is running).
INT prtHSBertSlt	1.3.6.1.4.1.164.3.3.3.3.2.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtHSClkMode	1.3.6.1.4.1.164.3.3.3.3.1.1.6	INTEGER	read-write	Clock Mode of the user data channel. dce - DACS operates as a DCE and provides transmit and receive clocks to the synchronous user DTE. dte1- DACS supplies the receive clock to the user equipment and accepts the user transmit clock. dte2- DACS requires transmit and receive clocks from the user equipment.
INT prtHSClkPolarity	1.3.6.1.4.1.164.3.3.3.3.1.1.14	INTEGER	read-write	This object indicates the clock polarity.
INT prtHSCTS	1.3.6.1.4.1.164.3.3.3.3.1.1.7	INTEGER	read-write	Selection of CTS line state in the user data channel. on - CTS continuously ON. rts - CTS line follows the RTS line.
INT prtHSDCD	1.3.6.1.4.1.164.3.3.3.3.1.1.13	INTEGER	read-write	Selection of DCD line state in the user data channel. linkOK - DCD line is ON only when active link is OK. on - DCD continuously ON.
INT prtHSFifoSize	1.3.6.1.4.1.164.3.3.3.3.1.1.5	INTEGER	read-write	This object selects the size of the user data channel buffer FIFO used in the DTE2 mode. In the other modes, buffer size is automatically set by the DACS agent. Buffer FIFO size in bits, corresponds to FIFO lengths of +/-16, +/-30, +/-52, +/-72 bits.
INT prtHsfPrtIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.3	INTEGER	read-only	This attribute indicates a unique external port index. Hs2 has only two ports (exPrt1,exPrt2). Hs3 has three ports (exPrt1,exPrt2,exPrt3). Hsq and hsqN has four ports. Hs6 has six external ports. Hs12 has twelve external ports. inPrt1, inPrt2 - are relevant for VID card.
INT prtHsfSltIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtHSInbandLoopback	1.3.6.1.4.1.164.3.3.3.3.1.1.9	INTEGER	read-write	This object indicates if Inband Loopback from the Network should be enabled or disabled.
INT prtHSInbandLoopPatternCfg	1.3.6.1.4.1.164.3.3.3.3.1.1.10	INTEGER	read-write	This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtHSActivatePolyPattern and prtHSDeactivatePolyPattern.
INT prtHSInterfaceType	1.3.6.1.4.1.164.3.3.3.3.1.1.15	INTEGER	read-write	This object indicates the selected electrical interface type.
INT prtHSRate	1.3.6.1.4.1.164.3.3.3.3.1.1.4	INTEGER	read-write	This object indicates the port rate (speed). auto - rate is selected automatically by system.
INT prtHSRtsState	1.3.6.1.4.1.164.3.3.3.3.1.1.8	INTEGER	read-only	RTS state of the port.
INT prtHSSlt	1.3.6.1.4.1.164.3.3.3.3.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtHSUnframed	1.3.6.1.4.1.164.3.3.3.3.1.1.16	INTEGER	read-write	Unframed line for HS ports. yes - means that all TSs must be transferred, including TS0. In this case, prtHSRate must be r31x56eq1736Kbps OR r31x64eq1984Kbps.
INT prtIConnect	1.3.6.1.4.1.164.3.3.3.6.1.1.4	INTEGER	read-write	D channel connection. no - disconnected yes - connected.
INT prtIn1p6VcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.2.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtIn1p6VcPbxEchoCanceler	1.3.6.1.4.1.164.3.2.3.2.15.2.1.6	INTEGER	read-write	Echo canceler activation.
INT prtIn1p6VcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtIn1p6VcPbxRate	1.3.6.1.4.1.164.3.2.3.2.15.2.1.5	INTEGER	read-write	This object indicates the port Rate. For Normal mode (prtIn7p8VcPbxMode=normal), only part of the values are valid (constant rate). For Server mode (prtIn7p8VcPbxMode=server), all values are applicable (user can select the desired compression rate).
INT prtIn1p6VcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtIn7p8VcPbxConnect	1.3.6.1.4.1.164.3.2.3.2.15.3.1.4	INTEGER	read-write	This object indicates whether the port should be considered in any of the mux algorithms.
INT prtIn7p8VcPbxLinkTo	1.3.6.1.4.1.164.3.2.3.2.15.3.1.9	INTEGER	read-write	This object indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For Server mode (prtIn7p8VcPbxMode=server), this object is not applicable. Both ports, 7 and 8 should be linked to the same Slot. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtIn7p8VcPbxMode	1.3.6.1.4.1.164.3.2.3.2.15.3.1.5	INTEGER	read-write	This object indicates the working mode of the port: - normal - the compressed voice will be sent to an MTML card inside the Mux. - server - the compressed voice will be sent to the Digital Voice connector, as a service to an outside user.
INT prtIn7p8VcPbxOos	1.3.6.1.4.1.164.3.2.3.2.15.3.1.8	INTEGER	read-write	Out of service Signaling mode.
INT prtIn7p8VcPbxPrtIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtIn7p8VcPbxRate	1.3.6.1.4.1.164.3.2.3.2.15.3.1.6	INTEGER	read-write	This object indicates the port Main Rate. For Server mode (prtIn7p8VcPbxMode=server), the value will be notApplicable.
INT prtIn7p8VcPbxSignalMode	1.3.6.1.4.1.164.3.2.3.2.15.3.1.7	INTEGER	read-write	This object indicates the Signal Mode. For Server mode (prtIn7p8VcPbxMode=server), the only valid values are: - none - aBit
INT prtIn7p8VcPbxSltIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtInHsiConnect	1.3.6.1.4.1.164.3.2.3.2.8.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInHsiRate	1.3.6.1.4.1.164.3.2.3.2.8.2.1.5	INTEGER	read-write	This object indicates the port speed. For HS-U/I and HS-S ports: 2 bit - up to 9600bps 4 bit - 19200bps 8 bit - 38400bps .. 64kbps. concentrated - this D channel goes to a Concentration channel, that represents many channels that this value was selected for them. The Concentrated channel is an Internal D Channel of the same card. This value is applicable only for D channels, except Concentration channel itself. --for HS-S and HS-U/I cards the Concentration channel will always be: internal-13 --for MP-2200 HS-S12, HS-S6, HS-U12, HS-U6 and DXC HS-U8 and HS-U16 cards, the Concentration channel is selected via the prtInHsiConcentratedTo object. notConnected - same as prtInHsiConnect=no.
INT prtInHsiSltIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.2	INTEGER	read-only	This object indicates a unique slot position where the card is inserted.
INT prtInLs2Connect	1.3.6.1.4.1.164.3.2.3.2.4.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel.
INT prtInLs2EnvAssign	1.3.6.1.4.1.164.3.2.3.2.4.2.1.8	INTEGER	read-write	Envelope assignment type.
INT prtInLs2LinkTo	1.3.6.1.4.1.164.3.2.3.2.4.2.1.7	INTEGER	read-write	It indicates the slot of the main link card to which the LS2 card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInLs2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.3	INTEGER	read-only	This attribute indicates a unique internal port index.
INT prtInLs2SltIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtInLs6Connect	1.3.6.1.4.1.164.3.2.3.2.13.3.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel.
INT prtInLs6LinkTo	1.3.6.1.4.1.164.3.2.3.2.13.3.1.8	INTEGER	read-write	It indicates the slot of the main link card to which the Ls6 card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - when prtInLs6TandemMode=tandemSlave. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInLs6PrtIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.3	INTEGER	read-only	This attribute indicates a unique internal port index.
INT prtInLs6Rate	1.3.6.1.4.1.164.3.2.3.2.13.3.1.6	INTEGER	read-write	Main Rate in Kbps.
INT prtInLs6RemoteType	1.3.6.1.4.1.164.3.2.3.2.13.3.1.7	INTEGER	read-write	Remote Type. notApplicable - when prtInLs6TandemMode=tandemSlave
INT prtInLs6SltIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtInLs6TandemMode	1.3.6.1.4.1.164.3.2.3.2.13.3.1.5	INTEGER	read-write	This object indicates the Tandem Mode. tandemSlave - is valid only for an LS-6 card having on the (current slot-1) an LS-6 card with 'tandemMaster' mode.
INT prtInMbeConnect	1.3.6.1.4.1.164.3.2.3.2.11.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInMbeLinkTo	1.3.6.1.4.1.164.3.2.3.2.11.2.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInMbePrtIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtInMbeRate	1.3.6.1.4.1.164.3.2.3.2.11.2.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInMbeSltIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtInPh1MlAssociatedExCh	1.3.6.1.4.1.164.3.2.3.2.2.3.1.20	INTEGER	read-write	This object indicates the external port associated to this internal port. At present, it is used by the Hybrid (mp2100h), MHS-4 cards which can have up to 64 dynamic internal ports associated with External ports. For ISDN cards, the value will be: notApplicable (255). The associated external of an ISDN internal port is represented by the MIB object: prtIsdnDirectoryPrtNu.
INT prtInPh1MlBearerCh	1.3.6.1.4.1.164.3.2.3.2.2.3.1.19	INTEGER	read-write	Defines which B (bearer) channels are used for transferring ISDN data. Default value is: none (255). anyChannel (2) is skipped because it is not in use here.
INT prtInPh1MlCcittCrc	1.3.6.1.4.1.164.3.2.3.2.2.3.1.23	INTEGER	read-write	This object indicates how many Bits are used for CRC (HDLC item).
INT prtInPh1MlClockEncoding	1.3.6.1.4.1.164.3.2.3.2.2.3.1.21	INTEGER	read-write	This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols.
INT prtInPh1MlCongResponse	1.3.6.1.4.1.164.3.2.3.2.2.3.1.8	INTEGER	read-write	This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/receive becn to/from the network). no - do nothing FlowControl - translate the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done in both directions.
INT prtInPh1MlConnect	1.3.6.1.4.1.164.3.2.3.2.2.3.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInPh1MlConnectionTyp	1.3.6.1.4.1.164.3.2.3.2.2.3.1.7	INTEGER	read-write	This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management operation (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetNotMana - indicates network internal line, but the remote mux is not managed by the nms. User - User to Network Interface. OtherNet - Network To Network Interfce. PubNet - Access Mux To PubNet Interface.
INT prtInPh1MlDlciIConPrt	1.3.6.1.4.1.164.3.2.3.2.2.4.1.7	INTEGER	read-write	This attribute indicates a unique port id which the dlci is routed to.
INT prtInPh1MlDlciIConSlt	1.3.6.1.4.1.164.3.2.3.2.2.4.1.6	INTEGER	read-write	This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtInPh1MlDlciPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.3	INTEGER	read-only	This attribute indicates a unique internal port number. MPH.1/E1 and MPH.1/T1 cards have three internal ports.
INT prtInPh1MlDlciRxBc	1.3.6.1.4.1.164.3.2.3.2.2.4.1.11	INTEGER	read-write	This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line.
INT prtInPh1MlDlciRxBe	1.3.6.1.4.1.164.3.2.3.2.2.4.1.12	INTEGER	read-write	This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line.
INT prtInPh1MlDlciSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
INT prtInPh1MlDlciStatus	1.3.6.1.4.1.164.3.2.3.2.2.4.1.14	INTEGER	read-only	This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
INT prtInPh1MlDlciTxBc	1.3.6.1.4.1.164.3.2.3.2.2.4.1.9	INTEGER	read-write	This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line.
INT prtInPh1MlDlciTxBe	1.3.6.1.4.1.164.3.2.3.2.2.4.1.10	INTEGER	read-write	This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line.
INT prtInPh1MlDlciValid	1.3.6.1.4.1.164.3.2.3.2.2.4.1.5	INTEGER	read-write	This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
INT prtInPh1MlFlowControl	1.3.6.1.4.1.164.3.2.3.2.2.3.1.11	INTEGER	read-write	This attribute indicates the required flow control betweeen the port and the remote equipment.
INT prtInPh1MlFrameSeparator	1.3.6.1.4.1.164.3.2.3.2.2.3.1.24	INTEGER	read-write	This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line.
INT prtInPh1MlFrMngProt	1.3.6.1.4.1.164.3.2.3.2.2.3.1.13	INTEGER	read-write	This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtInPh1MlConnectionTyp = sameNetManaged, this object will be RO (internally determined).
INT prtInPh1MlProtocol	1.3.6.1.4.1.164.3.2.3.2.2.3.1.6	INTEGER	read-write	This attribute indicates the applied protocol.
INT prtInPh1MlRate	1.3.6.1.4.1.164.3.2.3.2.2.3.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInPh1MlSegment	1.3.6.1.4.1.164.3.2.3.2.2.3.1.12	INTEGER	read-write	This object is the Segmentation in Bytes. In protocol FR+, ISDN internals, MX 30/300 the segmentation is: 50 (2) ,158 (3) ,266 (4) ,376 (5), 484 (6) In MX 3000/4: For protocol FR+ (internal ISDN ports of MHS.S, MHS.U, MHS.E1, MHS.T1 cards) segmentation values are: 236 (7),472 (8), 708 (9), 944 (10) ,1180 (11)
INT prtInPh1MlSltType	1.3.6.1.4.1.164.3.2.3.2.2.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For ISDN BRI port of MX300/30: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtInPh1MlTc	1.3.6.1.4.1.164.3.2.3.2.2.3.1.10	INTEGER	read-write	This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports in the specific card. 255=notApplicable.
INT prtInTreConnect	1.3.6.1.4.1.164.3.2.3.2.12.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInTreLinkTo	1.3.6.1.4.1.164.3.2.3.2.12.2.1.6	INTEGER	read-write	It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInTrePrtIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.3	INTEGER	read-only	A unique port identifier within the card.
INT prtInTreRate	1.3.6.1.4.1.164.3.2.3.2.12.2.1.5	INTEGER	read-write	This attribute indicates the port speed.
INT prtInTreSltIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtInVc3Connect	1.3.6.1.4.1.164.3.2.3.2.14.2.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtInVc3LinkTo	1.3.6.1.4.1.164.3.2.3.2.14.2.1.7	INTEGER	read-write	This attribute indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
INT prtInVc3Oos	1.3.6.1.4.1.164.3.2.3.2.14.2.1.6	INTEGER	read-write	This object is equal for all the ports in the specific card because of HW limitations
INT prtInVc3PrtIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.3	INTEGER	read-only	A unique identifier of the port, within the card.
INT prtInVc3Rate	1.3.6.1.4.1.164.3.2.3.2.14.2.1.5	INTEGER	read-write	Rate in bps.
INT prtInVc3SltIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtIpParamConnect	1.3.6.1.4.1.164.6.2.15.6.1.1.18	INTEGER	read-write	Port Connection.
INT prtIpParamEncapsulationProt	1.3.6.1.4.1.164.6.2.15.6.1.1.20	INTEGER	read-write	Encapsulation Protocol.
INT prtIpParamLimitPacketType	1.3.6.1.4.1.164.6.2.15.6.1.1.33	INTEGER	read-write	The packet type that will be rate limited. Rate limitation determined in prtIpParamRateLimit. all - All packet types are rate limited. broadMultiFloodedUnicast - Broadcast, Multicast and Flooded Unicast packets are rate limited. broadcastMulticast - Broadcast and Multicast packets are rate limited. broadcast - Broadcast packets are rate limited.
INT prtIpParamMaxTxBandwidth	1.3.6.1.4.1.164.6.2.15.6.1.1.16	INTEGER	read-write	This object shows the Max Bandwidth allowed on the LAN. Full - means that a Maximum of 100 Mega Byte Rate may go through the LAN. e1(3) means that the maximum is an E1 rate. t1(4) is for a maximum of a T1 rate.
INT prtIpParamMediaMode	1.3.6.1.4.1.164.6.2.15.6.1.1.7	INTEGER	read-only	This object indicates the real Media Mode.
INT prtIpParamMediaRate	1.3.6.1.4.1.164.6.2.15.6.1.1.8	INTEGER	read-only	This object indicates the real Media Rate (Mbps).
INT prtIpParamMng	1.3.6.1.4.1.164.6.2.15.6.1.1.30	INTEGER	read-write	This object indicates whether Management is enabled/disabled via this port.
INT prtIpParamMngVlanSupport	1.3.6.1.4.1.164.6.2.15.6.1.1.9	INTEGER	read-write	Management VLAN support (Tagging). no - No support of VLAN Tagging. yes - 4 VLAN bytes will be added to the frame.
INT prtIpParamProtIpEnable	1.3.6.1.4.1.164.6.2.15.6.1.1.13	INTEGER	read-write	This object indicates whether a list of Protected IP Addresses is enabled or not. This object is applicable only if prtIpParamRingMode=enable.
INT prtIpParamRingMode	1.3.6.1.4.1.164.6.2.15.6.1.1.12	INTEGER	read-write	This object indicates If Ring Mode is enabled or not.
INT prtIpParamTrafficPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.14	INTEGER	read-write	This object indicates the traffic priority of this port.
INT prtIpParamVlanSupport	1.3.6.1.4.1.164.6.2.15.6.1.1.22	INTEGER	read-write	VLAN support (Tagging). 'no' - No support of VLAN Tagging. 'yes' - 4 VLAN bytes will be added to the frame.
INT prtIpParamVlanTagging	1.3.6.1.4.1.164.6.2.15.6.1.1.27	INTEGER	read-write	VLAN Tagging. 'unmodified' - No change will be done to the Frame. 'tag' - Add Tag to Untagged Frames. 'doubleTag' - Add Tag to all Frames. 'doubleTagAndFallBack' - Double Tagging will have different rules for VLANs that this port is member in, than these it is not a member in. 'untag' - Remove Tag from tagged frames.
INT prtIRate	1.3.6.1.4.1.164.3.3.3.6.1.1.3	INTEGER	read-write	This object indicates the port rate in bits. Each TS contains 8 bits. Thus, 1 bit is equivalent to 8Kbps rate.
INT prtIsdnAbSide	1.3.6.1.4.1.164.3.2.3.2.16.1.1.12	INTEGER	read-write	This parameter indicates the QSIG side in layer 3. This definition is from the QSIG Standard.
INT prtIsdnBasicRateLineTopology	1.3.6.1.4.1.164.3.2.3.2.16.1.1.6	INTEGER	read-write	This attribute is relevant for ISDN BRI only. It is equivalent to isdnBasicRateLineTopology in the isdn MIB.
INT prtIsdnCallMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.15	INTEGER	read-write	This object indicates the acceptance of incoming calls. Initiate - Callout Listen - Callin.
INT prtIsdnConnect	1.3.6.1.4.1.164.3.2.3.2.16.1.1.4	INTEGER	read-write	This attribute indicates if the port is connected.
INT prtIsdnDirectorySltIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For MX300/30 ports: io1(5) = isdn1(5) and io2(6) = isdn2(6). In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
INT prtIsdnEndpointBearerCh	1.3.6.1.4.1.164.3.2.3.2.16.2.1.8	INTEGER	read-create	This is the selected dialing channel. anyChannel - the system selects the dialing channel.
INT prtIsdnEndpointIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.4	INTEGER	read-only	Since more than one endpoint may be defined per isdn entity, this field is a simple index. It corresponds to isdnEndpointIdx in the isdn MIB.
INT prtIsdnEndpointSltIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
INT prtIsdnEndpointTeiType	1.3.6.1.4.1.164.3.2.3.2.16.2.1.5	INTEGER	read-create	The type of TEI (Terminal Endpoint Identifier) used for this Terminal Endpoint. In case of dynamic(1), the TEI value is selected by the switch. In case of static(2), a valid TEI value has to be entered in the isdnEndpointTeiValue object. interface type as well as the Terminal Endpoint type. static(2). On Basic Rate interfaces the default value is dynamic(1) for isdn(63) Terminal Endpoints. It corresponds to isdnEndpointTeiType in the isdn MIB.
INT prtIsdnFilter	1.3.6.1.4.1.164.3.2.3.2.16.1.1.8	INTEGER	read-write	This attribute allows the user to configure the port: answerAll(2): accept all incoming calls, rejectAll(3): reject all incoming calls, selective(4): accept or reject according directory table. callBack (5): In this mode the ISDN Ch will reject incoming calls and will initiate call back to the rejected phone number.
INT prtIsdnInterface	1.3.6.1.4.1.164.3.2.3.2.16.1.1.14	INTEGER	read-write	It indicates the interface type: lt = line termination nt = network termination te = terminal equipment.
INT prtIsdnMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.7	INTEGER	read-write	This attribute allows the user to configure the port as leased(2) in case of connection to a TDM network.
INT prtIsdnQsigRole	1.3.6.1.4.1.164.3.2.3.2.16.1.1.13	INTEGER	read-write	This parameter indicates the QSIG side in layer 1 & 2.
INT prtIsdnSignalingProtocol	1.3.6.1.4.1.164.3.2.3.2.16.1.1.5	INTEGER	read-write	This attribute fixes which signaling protocol is used at this port (D-Channel). It is equivalent to isdnSignalingProtocol in the isdn MIB.
INT prtIsdnSimultaneousCall	1.3.6.1.4.1.164.3.2.3.2.16.1.1.9	INTEGER	read-write	In case of simultaneous call (local,remote and remote,local): accept(2): accept the incoming call, reject(3): reject the incoming call.
INT prtIsdnSltIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
INT prtIsdnStatusCallDirection	1.3.6.1.4.1.164.3.2.3.1.16.1.6	INTEGER	read-only	Attribute indicating the Direction of the Call. The value of notApplicable will be used for example when prtIsdnStatusCallState = notActive(14).
INT prtIsdnStatusCallState	1.3.6.1.4.1.164.3.2.3.1.16.1.2	INTEGER	read-only	The state that the current call is in.
INT prtIsdnStatusDspMode	1.3.6.1.4.1.164.3.2.3.1.16.1.1	INTEGER	read-only	The DSP can be in one of the following Modes: Voice, Idle, Fax, Voice Band Data (VBD)- Modem.
INT prtIsdnSwitchMode	1.3.6.1.4.1.164.3.2.3.2.16.1.1.11	INTEGER	read-write	For KM2100. auto - The call is initiated automatically by one of the IO cards connected to KML.10(ISDN card) having ISDN Switch Mode. manual - The call is initiated by the user manually, for KML.10 having ISDN Switch Mode (via mdlSCmd). connect- The call is initiated 'immediately', for KML.10 having ISDN Switch Mode. 'immediately'- means: immediately after power-up (when product performed Reset) OR, since this value appears in the active configuration. In this case, the call can be disconnected only by power-off of the product or by changing this object to another value (or actual Remove of the KML.10 relevant card). notApplicable - For other card types.
INT prtLanWanEgressVlanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.6	INTEGER	read-write	This object determines what to do with the VLAN frames that exit via the WAN side of the port. This object is not applicable when prtLanWanMode=l3SubnetSwitch(4).
INT prtLanWanL2Protocol	1.3.6.1.4.1.164.3.2.3.2.22.1.1.7	INTEGER	read-write	L2 Protocol. When prtLanWanMode=l3SubnetSwitch(4), the only valid value is ppp(3).
INT prtLanWanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.4	INTEGER	read-write	This object determines the working mode of this port. For FCD155, layer3SubnetSwitch is not applicable
INT prtLanWanSltIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.2	INTEGER	not-accessible	This object indicates a unique slot position where the module is inserted.
INT prtLanWanToLanVlanMode	1.3.6.1.4.1.164.3.2.3.2.22.1.1.10	INTEGER	read-write	This object determines what to do with the VLAN frames that come from WAN side of the port and exit towards one of the LAN ports. This object is applicable only when prtLanWanDestIf=100 or 101 (Switching Table or inPrt1).
INT prtLanWanVlanType	1.3.6.1.4.1.164.3.2.3.2.22.1.1.14	INTEGER	read-write	This oject indicates type of VLAN this port is assigned to. Port Base Vlan parameters are defined by objects under radBridgePortBaseVlan
INT prtLogicalConnect	1.3.6.1.4.1.164.3.2.3.2.17.1.1.4	INTEGER	read-create	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtLogicalFunction	1.3.6.1.4.1.164.3.2.3.2.17.1.1.5	INTEGER	read-create	This parameter defines the function of the relevant channel.
INT prtLogicalSltIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.2	INTEGER	read-only	Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
INT prtMl4CGA	1.3.6.1.4.1.164.3.2.3.2.19.1.1.5	INTEGER	read-write	This object selects the method used to signal the CGA state to the other end, through the main link. 'none' - non-transparent mode. When one of the links (main) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos' will be transmitted to the other end. 'trans' - when one of the links (main) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos' will be transmitted to the other end.
INT prtMl4CrossConnectLevel	1.3.6.1.4.1.164.3.2.3.2.19.1.1.20	INTEGER	read-write	This object indicates whether the cross connect is on DS1 or DS0 (time-slots) level. When cross connect level is ds1, Destination Slot is indicated by prtGenCnfgLinkToSlot, Destination Port is indicated by prtGenCnfgLinkToPort. For Unframed Line Type, cross connect level can be either notApplicable (NC=not connected) or DS1. Otherwise, default value is ds0.
INT prtMl4EchoCanceler	1.3.6.1.4.1.164.3.2.3.2.19.1.1.13	INTEGER	read-write	Echo canceler activation.
INT prtMl4Oos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.6	INTEGER	read-write	'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0
INT prtMl4OosErrorSource	1.3.6.1.4.1.164.3.2.3.2.19.1.1.14	INTEGER	read-write	OOS (Out-of-Service) Error Source. This object is applicable for T1 ports only.
INT prtMl4PppEchoFailDetection	1.3.6.1.4.1.164.3.2.3.2.19.1.1.21	INTEGER	read-write	This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Disable. Enable - will be selected mainly when a T1/E1 Ring exists and between 2 adjacent Ring devices there is another device or Net, that causes these Ring devices not to sense that the PPP connection between them is lost. In this case, Echo Request should be initiated by the port.
INT prtMl4PrtIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.3	INTEGER	read-only	This attribute indicates a unique port number.
INT prtMl4RemCrc	1.3.6.1.4.1.164.3.2.3.2.19.1.1.19	INTEGER	read-write	This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.
INT prtMl4Service	1.3.6.1.4.1.164.3.2.3.2.19.1.1.9	INTEGER	read-write	Link Service. leasedLine - usual TDM interface. v51 - V5.1 interface. v52Master - V5.2 Link to Local Exchange. v52Slave - a ML that is transferred to the v52Master.
INT prtMl4SignalingMode	1.3.6.1.4.1.164.3.2.3.2.19.1.1.12	INTEGER	read-write	Refers to the signaling mode of the port (or framer module). notApplicable(1)- means that no framer is needed for this port (no signaling), or that this object is not relevant. cas(2) means Channel Associated Signaling. Used for E1 Links. ccs(3) is the Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). robbedBit(4) is a method implementing 7 bits for the voice and 1 bit dedicated for signaling. Used for T1 Links. other (5)- Signaling generally exists though not specifically according to one of the values listed ; this port uses a framer in this case.
INT prtMl4SigProfile	1.3.6.1.4.1.164.3.2.3.2.19.1.1.4	INTEGER	read-write	This object indicates the Signaling Profile of the port. none - when the Frame is G732N (no MF) or Unframed. p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5 perTS = when Signaling Profile is selected per TS.
INT prtMl4SltIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted.
INT prtMonitoringEnable	1.3.6.1.4.1.164.3.3.3.1.6.1.3	INTEGER	read-write	This object indicates if the prtMonitoringIdx is configured as a monitoring port or not. disabled = the port is NOT configured to monitor. Setting this object to this value will cause reset (to 0) of the prtMonitoringTSs and prtMonitoredTSs objects. enabled = the port IS configured to monitor. For Optimux-T3: always enabled (RO supported).
INT prtParamAlarmIndication	1.3.6.1.4.1.164.6.2.15.5.1.1.13	INTEGER	read-only	This object indicates status-aggregation of non-masked alarms associated with all interface layers, related to this physical port. When at least one non-masked alarm exists on any layer, value of this object is on (3). Indication will be off (2) only when there's no active non-masked alarm on any interface layer related to this port. Masking an Alarm, will consider it as not exist for this indication. Example: When a port has an ATM higher layer and at least one VC has alarm, value of this object will be on (3)
INT prtParamClearAlarm	1.3.6.1.4.1.164.6.2.15.5.1.1.8	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Port Alarms. Upon completion, the value will automatically change to off(2).
INT prtParamClkSrc	1.3.6.1.4.1.164.6.2.15.5.1.1.3	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' or 'loopback' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' or 'internal' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' or 'external' indicates that recovered receive clock from another card or interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'master' and 'fallback' values may be used RO to indicate active clock. 'station' - indicate clock received from station port is used as transmit clock.
INT prtParamClkSsmRxSource	1.3.6.1.4.1.164.6.2.15.5.1.1.24	INTEGER	read-write	This object indicates the Sa-bit of the E1 frame, in which SSM messages are carried.
INT prtParamClkWaveShape	1.3.6.1.4.1.164.6.2.15.5.1.1.15	INTEGER	read-write	Wave shape of station clock source signal.
INT prtParamInterfaceType	1.3.6.1.4.1.164.6.2.15.5.1.1.7	INTEGER	read-write	The type of the port.
INT prtParamLineLength	1.3.6.1.4.1.164.6.2.15.5.1.1.10	INTEGER	read-write	Line Length of the line connected to this port.
INT prtParamLoopDetect	1.3.6.1.4.1.164.6.2.15.5.1.1.20	INTEGER	read-write	Enable/disable Loop Detection on a port. Examples of ports: physical, Channelized Bundle over TDM Uplink, Bridge Ports.
INT prtParamMappingMode	1.3.6.1.4.1.164.6.2.15.5.1.1.12	INTEGER	read-write	This object defines path protection on SONET/SDH link Auto - SONET/SDH mapping for port is copied automatically to same TU on the redundant SONET/SDH local (reside on same slot) link by agent. Manual - the user can configure the redundant mapping for port on the same link or to the other link on any TU Adjacent - similar to auto, but mapping is copied automatically by agent to link on adjacent slot .
INT prtParamPhantom	1.3.6.1.4.1.164.6.2.15.5.1.1.4	INTEGER	read-write	Power feeding to another device.
INT prtParamPSNLayer	1.3.6.1.4.1.164.6.2.15.5.1.1.22	INTEGER	read-write	This object indicates the network layer from which clock is derived.
INT prtParamResetStatsCmd	1.3.6.1.4.1.164.6.2.15.5.1.1.5	INTEGER	read-write	Reset statistics of the selected port.
INT prtParamRxSsm	1.3.6.1.4.1.164.6.2.15.5.1.1.23	INTEGER	read-write	This object indicates if Station Clock SSM messages received will serve as criteria for clock selection.
INT prtParamStatus	1.3.6.1.4.1.164.6.2.15.5.1.1.16	INTEGER	read-only	Station clock source Status.
INT prtParamTxClk	1.3.6.1.4.1.164.6.2.15.5.1.1.27	INTEGER	read-write	enable/disable station clock signal output.
INT prtParamUsage	1.3.6.1.4.1.164.6.2.15.5.1.1.11	INTEGER	read-write	Defines whether this port works as User port or as Network port.
INT prtPerfPeriodRef	1.3.6.1.4.1.164.6.2.15.3.1.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. lastPeriod - the period between last two commands of prtPerfSaveAndResetCmd. - If only one command occured since Start-up: the period between Start-up and last command. - If no command occured since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
INT prtPerfSaveAndResetCmd	1.3.6.1.4.1.164.6.2.15.3.1.1.10	INTEGER	read-write	A command per port/interface, to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. This object is applicable only for prtPerfPeriodRef=currentPeriod. Setting this object to on(3) for prtPerfPeriodRef=last, will cause the agent to return: Bad Value response. When setting validly this object to on(3), agent will perform the required command and will reset automatically the value of this object to off(2). Setting this object to off(2), will do nothing.
INT prtPhMlBus	1.3.6.1.4.1.164.3.2.3.2.2.5.1.11	INTEGER	read-write	The TDM BUS this port is linked to.
INT prtPhMlCAS	1.3.6.1.4.1.164.3.2.3.2.2.5.1.6	INTEGER	read-write	This attribute indicates whether Channel Associated Signaling (CAS) is used.
INT prtPhMlClockMode	1.3.6.1.4.1.164.3.2.3.2.2.5.1.7	INTEGER	read-write	Clock mode.
INT prtPhMlClockPolarity	1.3.6.1.4.1.164.3.2.3.2.2.5.1.18	INTEGER	read-write	This object indicates the clock polarity.
INT prtPhMlClockSource	1.3.6.1.4.1.164.3.2.3.2.2.5.1.13	INTEGER	read-write	The Clock Source: TC (Tx Clock) or RC (Rx Clock) signals.
INT prtPhMlConnect	1.3.6.1.4.1.164.3.2.3.2.2.5.1.4	INTEGER	read-write	This attribute indicates whether the port should be considered in any of the mux algorithms.
INT prtPhMlControlSignals	1.3.6.1.4.1.164.3.2.3.2.2.5.1.16	INTEGER	read-write	This object shows whether the Port will ignore or implement the control signals like DCD, CTS, DTR.
INT prtPhMlCorrectionMode	1.3.6.1.4.1.164.3.2.3.2.2.5.1.15	INTEGER	read-write	This object is applicable only when prtPhMlErrCorrection=yes. random - enables to correct up to 3 random errors in an 23 bit frame built from 12 data bits and 11 appended parity bits. bursty - interleaving 3 frames, allows correcting bursts of 9 bit length.
INT prtPhMlDialProcess	1.3.6.1.4.1.164.3.2.3.2.2.5.1.9	INTEGER	read-write	Dial Process.
INT prtPhMlErrCorrection	1.3.6.1.4.1.164.3.2.3.2.2.5.1.14	INTEGER	read-write	This object indicates if Error Correction mechanism should be applied or not. It will be applicable only if the interface HW includes the Error Correction chip.
INT prtPhMlInterfaceType	1.3.6.1.4.1.164.3.2.3.2.2.5.1.17	INTEGER	read-write	The SW Configurable Interface Type.
INT prtPhMlMfSyncSlot	1.3.6.1.4.1.164.3.2.3.2.2.5.1.12	INTEGER	read-write	This attribute indicates whether the sync is synchronized according to a certain card and the slot of this card. This operation is required in order to bypass signaling of PCM voice channels. In the ?004 Unit the entries io6(10)..io12(16) are not valid
INT prtPhMlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.3	INTEGER	read-only	This attribute indicates a unique port number. ML-20 cards have just one external interface.
INT prtPhMlRate	1.3.6.1.4.1.164.3.2.3.2.2.5.1.5	INTEGER	read-write	This attribute indicates the configured port speed. auto - rate is adapted automatically to the attached modem rate.
INT prtPhMlSatBuffer	1.3.6.1.4.1.164.3.2.3.2.2.5.1.8	INTEGER	read-write	Satellite Buffer (+/- 256).
INT prtPhMlSltIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used.
INT prtQosDirection	1.3.6.1.4.1.164.6.3.4.2.1.3	INTEGER	not-accessible	This object indicates the port's QoS Direction.
INT prtQosRateLimitPacketType	1.3.6.1.4.1.164.6.3.4.2.1.4	INTEGER	read-write	This object indicates the Type of Packets on which Rate Limitation is applied.
INT prtSActiveStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.5	INTEGER	read-only	This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the ch is not connected according to the active config. offLine(3) indicates that the ch is down (not working) because of any problem. onLine(4) indicates that the ch is up (working) offLineRedundancy(5) indicates that the ch is down, because it is redundant port. onLineRedundancy(6) indicates that the ch is up, and it is the active link
INT prtSAlarmInvert	1.3.6.1.4.1.164.3.3.3.1.4.1.1.6	INTEGER	read-only	Alarm Invert is : on/off.
INT prtSAlarmMask	1.3.6.1.4.1.164.3.3.3.1.4.1.1.5	INTEGER	read-only	Alarm Mask is : on/off.
INT prtSAlarmOnOff	1.3.6.1.4.1.164.3.3.3.1.4.1.1.7	INTEGER	read-only	Alarm state is : on/off.
INT prtSAlarmState	1.3.6.1.4.1.164.3.3.3.1.4.1.1.4	INTEGER	read-only	This object indicates the port alarm severity.
INT prtSAlrCardType	1.3.6.1.4.1.164.3.1.4.1.2.1.11	INTEGER	read-only	This attribute indicates the type of card installed in the specific slot position. The enumeration is according to mdlSInstCardType.
INT prtSAlrInvert	1.3.6.1.4.1.164.3.1.4.1.2.1.10	INTEGER	read-only	Alarm invert : on/off.
INT prtSAlrMask	1.3.6.1.4.1.164.3.1.4.1.2.1.9	INTEGER	read-only	Alarm mask : on/off.
INT prtSAlrSeverity	1.3.6.1.4.1.164.3.1.4.1.2.1.6	INTEGER	read-only	The severity of the alarm.
INT prtSAlrSltIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.2	INTEGER	read-only	This attribute indicates a unique identifier of the slot where the card is inserted. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
INT prtSAlrState	1.3.6.1.4.1.164.3.1.4.1.2.1.7	INTEGER	read-only	State of the alarm.
INT prtSAlrStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.6	INTEGER	read-only	Indicates the alarm state in the port(ch) agent level. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT prtSBertClrCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.12	INTEGER	read-write	Setting this attribute initiates bert count clear operation. It is valid only when bert test is active on the specific port.
INT prtSClearAlrCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.8	INTEGER	read-write	Setting this attribute to on(3) enforces a clear operation of the alarm status events in the given port. The clear operation will not be applied for masked/inverted alarms.
INT prtSExHsfInterfaceTyp	1.3.6.1.4.1.164.3.2.3.1.6.1.3	INTEGER	read-only	This attribute indicates a unique interface type of a selected port.
INT prtSExHsfPrtIdx	1.3.6.1.4.1.164.3.2.3.1.6.1.2	INTEGER	read-only	This attribute indicates a unique port number.
INT prtSExHsfRts	1.3.6.1.4.1.164.3.2.3.1.6.1.4	INTEGER	read-only	This attribute indicates a unique RTS control signal state.
INT prtSExHsfSltIdx	1.3.6.1.4.1.164.3.2.3.1.6.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
INT prtSInstPrtType	1.3.6.1.4.1.164.3.1.4.1.1.1.3	INTEGER	read-only	This attribute describes the type of the designated port. In MX 3000 only external & internal options are used. All the other options are only for MX 30/300 which need special handling. In order to support interface types in MX 3000, return an ascii string for prtSInterfaceType in this table or support the general RAD value of physicalConnector. External port - is a port with a physical connector. Internal port - might be of two types: a) A composite port which collects a few external ports data into a common bandwidth (usually routed through DS1 link) b) A port which gets only part of the external ports (usually a few DS0's) The following types are used when all ports are external/ internal and the connector/interface type is necessary (for example, stand-alone units): High Speed port types Low Speed port types Voice port types, CL port types. ISDN Voice in MX 30/300 Phase 4: voiceS0 (16), voiceU (17) should be used. ISDN Voice in MX 30/300 Phase 5: voiceQsigS(18), voiceQsigU (19) should be used.
INT prtSInstSltIdx	1.3.6.1.4.1.164.3.1.4.1.1.1.1	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted. In the ?004 Unit the entries io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
INT prtSMaskedAlrStat	1.3.6.1.4.1.164.3.1.4.1.1.1.7	INTEGER	read-only	Indicates the alarm state in the port(ch) agent level, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
INT prtSpActCallOut	1.3.6.1.4.1.164.3.3.3.4.1.1.20	INTEGER	read-write	This object indicates when to Activate Call-Out. It is used by FCD-T1/E1. always - to activate call-out always. linkFail - to activate call-out only when Link of Inband Management fails.
INT prtSpAlrRelayMode	1.3.6.1.4.1.164.3.3.3.4.1.1.21	INTEGER	read-write	This attribute indicates the Alarm Relay Mode. notApplicable - for DP.
INT prtSpAltNumMode	1.3.6.1.4.1.164.3.3.3.4.1.1.15	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. It determines wether to use the alternate number or not. Default = no.
INT prtSpCallOutMode	1.3.6.1.4.1.164.3.3.3.4.1.1.7	INTEGER	read-write	This attribute indicates the call-out mode. For DXC - this object is applicable only for the DP port (2).
INT prtSpCTS	1.3.6.1.4.1.164.3.3.3.4.1.1.9	INTEGER	read-write	CTS line state. This object is applicable only for port (1) = SP
INT prtSpDataBits	1.3.6.1.4.1.164.3.3.3.4.1.1.5	INTEGER	read-write	This attribute indicates the number of data bits in async frame
INT prtSpDcdDelay	1.3.6.1.4.1.164.3.3.3.4.1.1.10	INTEGER	read-write	DCD delay in msec. d10 = delay of 10msec. This object is applicable only for port (1) = SP
INT prtSpDialMode	1.3.6.1.4.1.164.3.3.3.4.1.1.14	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. Dialing mode. Default=tone
INT prtSpDsr	1.3.6.1.4.1.164.3.3.3.4.1.1.11	INTEGER	read-write	DSR line state. This object is applicable only for port (1) = SP
INT prtSpInterface	1.3.6.1.4.1.164.3.3.3.4.1.1.8	INTEGER	read-write	This attribute indicates the supervisory port interface. dce - the DACS appears as a DCE for the port. dte - the DACS operates as a DTE, for connection via modem, for the port.
INT prtSpParity	1.3.6.1.4.1.164.3.3.3.4.1.1.6	INTEGER	read-write	This attribute indicates the parity mode in async frame
INT prtSpRate	1.3.6.1.4.1.164.3.3.3.4.1.1.4	INTEGER	read-write	This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
INT prtSpRoutProtocol	1.3.6.1.4.1.164.3.3.3.4.1.1.18	INTEGER	read-write	This attribute indicates the routing protocol of the port. notApplicable - for DP.
INT prtSpStopBits	1.3.6.1.4.1.164.3.3.3.4.1.1.22	INTEGER	read-write	This attribute indicates number of stop bits in an async frame.
INT prtSpUsage	1.3.6.1.4.1.164.3.3.3.4.1.1.3	INTEGER	read-write	This attribute indicates what is the usage of the port.
INT prtSpWaitForConnect	1.3.6.1.4.1.164.3.3.3.4.1.1.13	INTEGER	read-write	For DXC - this object is applicable only for port (2) = DP. Waiting time for connect, in seconds. Default = 30 sec.
INT prtSRdnStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.17	INTEGER	read-only	Redundancy Status of this port. noRdn - this port is not part of a Redundancy pair/group. offline - this port is offline from Redundancy point of view. online - this port is online from Redundancy point of view.
INT prtSTstCmd	1.3.6.1.4.1.164.3.1.4.1.1.1.10	INTEGER	read-write	Setting this attribute to any of the above values will initiate a test on the specific port if the operation is legal. If the operation is not legal, the mux will ignore the operation. testPerTS(31) - when this test is selected, the selection of tests for each TS is done via the prtExPh1MlTsTest object. If a test time out is needed, the test will be set with a default timeout of 2 minutes until the user will set the parameter 'prtSTstDuration' to the required time out. If no time out is needed , the test will be set with infinite timeout until the user will set the parameter 'prtSTstDuration' to the required time out.
INT prtSupervisoryCTS	1.3.6.1.4.1.164.6.2.15.2.1.1.8	INTEGER	read-write	CTS line state.
INT prtSupervisoryDataBits	1.3.6.1.4.1.164.6.2.15.2.1.1.3	INTEGER	read-write	This attribute indicates the number of data bits in an async frame
INT prtSupervisoryDcdDelay	1.3.6.1.4.1.164.6.2.15.2.1.1.9	INTEGER	read-write	DCD delay in msec.
INT prtSupervisoryDSR	1.3.6.1.4.1.164.6.2.15.2.1.1.10	INTEGER	read-write	DSR line state.
INT prtSupervisoryInterface	1.3.6.1.4.1.164.6.2.15.2.1.1.7	INTEGER	read-write	This attribute indicates the supervisory port interface.
INT prtSupervisoryParity	1.3.6.1.4.1.164.6.2.15.2.1.1.4	INTEGER	read-write	This attribute indicates the parity mode in an async frame
INT prtSupervisoryRate	1.3.6.1.4.1.164.6.2.15.2.1.1.2	INTEGER	read-write	This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
INT prtSupervisoryRoutProtocol	1.3.6.1.4.1.164.6.2.15.2.1.1.11	INTEGER	read-write	This attribute indicates the routing protocol of the port. notApplicable - for DP.
INT prtSupervisoryStopBits	1.3.6.1.4.1.164.6.2.15.2.1.1.5	INTEGER	read-write	This attribute indicates the parity mode in an async frame.
INT prtSupervisoryUsage	1.3.6.1.4.1.164.6.2.15.2.1.1.6	INTEGER	read-write	This attribute indicates the usage of the SP port.
INT prtT1E1CGA	1.3.6.1.4.1.164.3.3.3.2.2.1.10	INTEGER	read-write	This object selects the method used to signal the CGA state to the other end, through the main/sub link. 'none' - non-transparent mode. When one of the links (main/sub) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos Signal' will be transmitted to the other end. 'trans' - when one of the links (main/sub) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main/sub) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos Signal' will be transmitted to the other end.
INT prtT1E1ConnectedTS	1.3.6.1.4.1.164.3.3.3.2.2.1.27	INTEGER	read-only	This parameter indicates if there is any connected TS for this interface.
INT prtT1E1EocTsConfig	1.3.6.1.4.1.164.3.3.3.2.2.1.32	INTEGER	read-write	This object indicates whether the use of EOC for TS Configuration is enabled or not.
INT prtT1E1Fdl	1.3.6.1.4.1.164.3.3.3.2.2.1.7	INTEGER	read-write	This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following is used. 'ansi-T1-403' refers to the FDL exchange recommended by ANSI. 'att-54016' refers to ESF FDL exchanges. 'fdl-none' indicates that the device does not use the FDL. 'transFdl' indicates transition between two ports of the same card.
INT prtT1E1FdlMode	1.3.6.1.4.1.164.3.3.3.2.2.1.8	INTEGER	read-write	Fdl Mode of the T1 selected port. notApplicable - will be used for an E1 port.
INT prtT1E1FdlMsgFdlType	1.3.6.1.4.1.164.3.3.3.2.3.1.2	INTEGER	read-only	The Fdl type reference of the Fdl message.
INT prtT1E1FdlMsgSlt	1.3.6.1.4.1.164.3.3.3.2.3.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtT1E1InbandMng	1.3.6.1.4.1.164.3.3.3.2.2.1.17	INTEGER	read-write	A unique number to identify an Inband management over the link. internal - supported by KM-2100 only. It means that the management is internal to the frame. It takes part of the ML Frame bits (instead of data).
INT prtT1E1InbandMngRate	1.3.6.1.4.1.164.3.3.3.2.2.1.18	INTEGER	read-write	A unique number to identify the rate of the Inband management. It is required only for E1 links and is applicable only when prtExT1E1InbandMng selected is FdlOrTs0 or dedicatedTs.
INT prtT1E1InbandMngRoutProt	1.3.6.1.4.1.164.3.3.3.2.2.1.20	INTEGER	read-write	Inband Mng Routing Protocol of the port. When prtT1E1InbandMng is 'dedicatedPpp'-'proprietary' and 'rip2' are applicable. For other values - only 'proprietary' is applicable. For FCD-M and FCD-A: When prtT1E1InbandMng is 'dedicatedPpp' or 'dedicatedFr': 'None', 'proprietary' and 'rip2' are applicable. When prtT1E1InbandMng is 'fdlOrTS0' or 'dedicatedTs': 'None' and 'proprietary' are applicable. When prtT1E1InbandMng is 'off': 'None' is applicable.
INT prtT1E1LineCode	1.3.6.1.4.1.164.3.3.3.2.2.1.5	INTEGER	read-write	This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. jbzs=b7zs refers the Jammed Bit Zero Suppres- sion, in which the AT&T specification of at least one pulse every 8 bit periods is literal- ly implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data (used for T1). b8zs refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits (used for T1). ANSI Clear Channels may use zbtsi, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use hdb3 or ami (= TRAN). amI (=TRAN) refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
INT prtT1E1LineLengthMask	1.3.6.1.4.1.164.3.3.3.2.2.1.15	INTEGER	read-write	This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft 'fcc68' - provides compliance with the FCC 68.308 Option A output pulse mask.
INT prtT1E1LineMode	1.3.6.1.4.1.164.3.3.3.2.2.1.25	INTEGER	read-write	Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values
INT prtT1E1LineType	1.3.6.1.4.1.164.3.3.3.2.2.1.4	INTEGER	read-write	This variable indicates the variety of T1/E1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: esf Extended SuperFrame DS1 d4 AT&T D4 format DS1 - SF e1 CCITT Recommendation G.704 (Table 4a) - G732N e1Crc CCITT Recommendation G.704 (Table 4b) - G732N with CRC e1MF G.704 (Table 4a) with TS16 multiframing enabled - G732S e1CrcMF G.704 (Table 4b) with TS16 multiframing enabled - G732S with CRC unframed T1 - applicable values: (1),(2),(3),(8) E1 - applicable values: (1),(4),(5),(6),(7),(8)
INT prtT1E1LinkMode	1.3.6.1.4.1.164.3.3.3.2.2.1.21	INTEGER	read-write	regular - TSs are connected by user via TS Assignment only transparent - when a port with this Link Mode is connected to an internal T1/E1 port of a T3/E3 card, TS0, TS16 and Fbit are transparently transferred to the E3/T3 stream.
INT prtT1E1Multiplier	1.3.6.1.4.1.164.3.3.3.2.2.1.22	INTEGER	read-write	The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps. For T1 only.
INT prtT1E1OosSignal	1.3.6.1.4.1.164.3.3.3.2.2.1.12	INTEGER	read-write	'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0
INT prtT1E1PppEchoFailDetection	1.3.6.1.4.1.164.3.3.3.2.2.1.34	INTEGER	read-write	This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Disable. Enable - will be selected mainly when a T1/E1 Ring exists and between 2 adjacent Ring devices there is another device or Net, that causes these Ring devices not to sense that the PPP connection between them is lost. In this case, Echo Request should be initiated by the port.
INT prtT1E1RAI	1.3.6.1.4.1.164.3.3.3.2.2.1.24	INTEGER	read-write	Remote Alarm Signal
INT prtT1E1RemCrc4	1.3.6.1.4.1.164.3.3.3.2.2.1.30	INTEGER	read-write	This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.
INT prtT1E1Role	1.3.6.1.4.1.164.3.3.3.2.2.1.33	INTEGER	read-write	This object indicates whether this port behaves as SUB or Main link.
INT prtT1E1RxGain	1.3.6.1.4.1.164.3.3.3.2.2.1.23	INTEGER	read-write	This attribute is the rx volume (dB).
INT prtT1E1SameFeCnfg	1.3.6.1.4.1.164.3.3.3.2.2.1.29	INTEGER	read-write	This parameter indicates whether the same E1 configuration parameters and TS assignment are set both to the local and remote device. Read-Write access is applicable only in G732N framed mode. For G732S and UNFRAMED this parameter is set by agent to YES and is Read Only. In Case of conflict during power-up between the central and remote, the value set by the central unit is the valid one.
INT prtT1E1SignalMode	1.3.6.1.4.1.164.3.3.3.2.2.1.6	INTEGER	read-write	'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Signaling is in use. 'bitOriented' indicates that E1 Channel Associated Signaling (CAS) is in use. 'messageOriented' indicates that Common Channel Signaling (CCS) is in use either on channel 16 of an E1 link or channel 24 of a T1.
INT prtT1E1Slt	1.3.6.1.4.1.164.3.3.3.2.2.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtT1E1SSlt	1.3.6.1.4.1.164.3.3.3.2.1.1.2	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtT1E1Sync	1.3.6.1.4.1.164.3.3.3.2.2.1.9	INTEGER	read-write	This object enables returning to normal operation, after the end of a main/sub link red alarm event, in reduced time. 'tr62411' - complies with AT&T TR-62411 (after 10 seconds). Applicable for both T1 and E1 interfaces. 'ccitt' - complies with CCITT standard. Applicable only for E1 interfaces. 'fast' - after 1 second.
INT prtT1E1Ts0SaBit	1.3.6.1.4.1.164.3.3.3.2.2.1.28	INTEGER	read-write	This parameter indicates whether to send TS 0, or not. noMng= TS 0 is looped, therefore not sent. mng= TS 0 isn't looped, therefore it is sent.
INT prtT1E1TxGainMask	1.3.6.1.4.1.164.3.3.3.2.2.1.16	INTEGER	read-write	This attribute is the tx gain mask parameter (dB), used only for T1/CSU interfaces.
INT prtT1FdlMsgFdlTxRx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.3	INTEGER	read-only	The Fdl tx/rx reference of the Fdl message.
INT prtT1FdlMsgPrtIdx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.2	INTEGER	read-only	This attribute indicates a unique port number. MTML-1/T1 modules have just one external interface.
INT prtT1FdlMsgSltIdx	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.1	INTEGER	read-only	This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
INT prtT3E3AisFrame	1.3.6.1.4.1.164.3.3.3.8.1.1.6	INTEGER	read-write	This object is applicable only for Optimux-T3. It allows user to select whether the AIS sent will be framed or unframed.
INT prtT3E3AisTransmit	1.3.6.1.4.1.164.3.3.3.8.1.1.9	INTEGER	read-write	Indicates if AIS signal will be transmitted over the tributary E3/DS3 upon failure.
INT prtT3E3InbandMng	1.3.6.1.4.1.164.3.3.3.8.1.1.5	INTEGER	read-write	A unique number to identify the Frame Type over the link. For Optimux-T3: only values (4), (7) are supported.
INT prtT3E3LineLength	1.3.6.1.4.1.164.3.3.3.8.1.1.4	INTEGER	read-write	This object is the length of the ds3 line in feet. It provides information for line build out circuitry if it exists and can use this object to adjust the line build out. len0p450ft = 0 - 450 feet len451p900ft = 451 - 900 feet.
INT prtT3E3RoutProt	1.3.6.1.4.1.164.3.3.3.8.1.1.8	INTEGER	read-write	Routing Protocol of the port. This object is applicable only for T3 ports.
INT prtT3E3Slt	1.3.6.1.4.1.164.3.3.3.8.1.1.3	INTEGER	read-only	This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
INT prtT3E3TxClockSource	1.3.6.1.4.1.164.3.3.3.8.1.1.7	INTEGER	read-write	Tx Clock Source.
INT prtTestInitiator	1.3.6.1.4.1.164.6.2.15.4.1.1.4	INTEGER	read-only	This object indicates who initiated this port's test/s.
INT prtTestMacSwapLoopDataMode	1.3.6.1.4.1.164.6.2.15.4.1.1.14	INTEGER	read-write	This object defines which part of the data will be looped back.
INT prtTestMacSwapLoopDirection	1.3.6.1.4.1.164.6.2.15.4.1.1.16	INTEGER	read-write	This object defines the direction of the performed loopback. In ETX102 'local' corresponds to Ingress loop (either on User port or on Network port), and 'remote' corresponds to Egress loop (either on User port or on Network port).
INT prtTestVctCmd	1.3.6.1.4.1.164.6.2.15.4.1.1.10	INTEGER	read-write	Vct command. on (3) = Start Vct on both cables connected to RX and TX connectors of this port. Agent will perform the required command and change automatically the value of this object to off(2).
INT prtTestVctRxResult	1.3.6.1.4.1.164.6.2.15.4.1.1.6	INTEGER	read-only	This object indicates the result of the Vct on the cable connected to the RX connector.
INT prtTestVctTxResult	1.3.6.1.4.1.164.6.2.15.4.1.1.7	INTEGER	read-only	This object indicates the result of the Vct on the cable connected to the TX connector.
INT prtVc2SltIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.2	INTEGER	read-only	This attribute indicates a unique slot position where the card is inserted. For Stand Alone products like WR: notApplicable (255)
INT qInternalProfileScheduling	1.3.6.1.4.1.164.6.3.11.2.1.3	INTEGER	read-create	This attribute determines the queue scheduling method.
INT radBridgeAction	1.3.6.1.4.1.164.4.1.1	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the tables maintained by the network device. Send actions are not currently implemented. Not all actions can be performed on all bridges.
INT radBridgeAgingTime	1.3.6.1.4.1.164.4.1.9.5	INTEGER	read-write	This variable defines whether the Aging Time will be finite or infinite. When selecting the finite (3) value, the exact time will be determined by another variable of the standard MIB (ex. 1493.dot1dTpAgingTime). or by radBridgeAgingTime below.
INT radBridgeAgingTimeSec	1.3.6.1.4.1.164.4.1.9.4.1.4	INTEGER	read-write	This variable duplicates scalar object dot1dTpAgingTimeThe of BRIDGE-MIB with configuration index and Bridge index. It defines the timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
INT radBridgeCODAnswerConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.5	INTEGER	read-write	CODCondAnswerConnect allows the user to specify the condition under which the link is connected. The options are: onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE .
INT radBridgeCODDay	1.3.6.1.4.1.164.4.1.4.2.1.2	INTEGER	read-only	The day of the week in which the dial up connection operates.
INT radBridgeCODImplicitSwitch	1.3.6.1.4.1.164.4.1.4.1.1.6	INTEGER	read-write	The inplicit switch allows the user to ignore implicit triggers provided by the COD software.
INT radBridgeCODManualConnect	1.3.6.1.4.1.164.4.1.4.1.1.2	INTEGER	read-write	The management station can start connection manually by setting this parameter
INT radBridgeCODMode	1.3.6.1.4.1.164.4.1.4.1.1.3	INTEGER	read-write	In answer mode only one incoming call may be accepted at a time. Other nodes attempting to access the local modem will receive a busy signal until the connection is terminated. (Answer mode has no difficulty supporting multiple remote connections to one local port, as blocking multiple incoming calls is just a modem function. Originate mode, on the other hand will only support a single local port to remote port connection). The disable parameter disables the COD utility for this interface. Choosing any other mode will enable the COD utility.
INT radBridgeCODOriginateConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.2	INTEGER	read-write	This condition, allows the user to specify the condition under which the link is connected. The options are onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=connect).
INT radBridgeCODOriginateDisConnectCondition	1.3.6.1.4.1.164.4.1.4.4.1.3	INTEGER	read-write	This condition allows the user to specify the condition under which the link is disconnected. The options are: noStationOnLan - When there is no station on lan. Counts 15 minutes from the point the last frame from lan has been received. If no frame have been transmitted on lan by the end of this period, disconnect the connection. onTraffic - On traffic. The user can specify the condition/s for disconnection. The disconnection will be defined in CODSpecificOnTrafficConditionOID . onDelayFromConnectionOnRequest - On Delay From Connection On Request . The delay time period will be defined in CODOriginateDisConnectDelay . onManualDisConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=disconnect).
INT radBridgeCODProtocolType	1.3.6.1.4.1.164.4.1.4.3.1.1.1	INTEGER	read-only	The Protocol Type of the Traffic Table
INT radBridgeCODTimeTriggerStatus	1.3.6.1.4.1.164.4.1.4.2.1.6	INTEGER	read-write	The status of a table entry.
INT radBridgeCODTrafficTriggerStatus	1.3.6.1.4.1.164.4.1.4.3.1.1.2	INTEGER	read-write	Command of Status of the Protocol Traffic Trigger
INT radBridgeDot1qVlanSplitHorizon	1.3.6.1.4.1.164.4.1.9.2.1.3	INTEGER	read-create	When 'enable (3)', packets having this VLAN will not be switched back to other bridge ports which are members of this VLAN.
INT radBridgeForwardingMode	1.3.6.1.4.1.164.4.1.12	INTEGER	read-write	This object determines the Bridge Forwarding Mode: transparent - Forward all frames received (not dependent on VLAN). filter - Filter frames received according to MAC Address. filterTagged = Filter frames received according to VLAN. transparentTagged = VLAN aware + Transparent.
INT radBridgeGenCfgBridgeAction	1.3.6.1.4.1.164.4.1.9.4.1.3	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the tables maintained by the Bridge. After performing the action, Agent will automatically Set the value of this variable to noOp(255).
INT radBridgeGenFlowBasicClassification	1.3.6.1.4.1.164.4.1.9.1.1.7	INTEGER	read-create	This object defines whether Classification based on Port should be taken into account (either as default, or in addition to other classifications).
INT radBridgeGenFlowQosMode	1.3.6.1.4.1.164.4.1.9.1.1.5	INTEGER	read-create	This object controls Quality of Service mode. User may select which field(s) (in case of fields - which one has precedence) will affect prioritization of data between egress queues.
INT radBridgeGenFlowSchedulingMode	1.3.6.1.4.1.164.4.1.9.1.1.6	INTEGER	read-create	This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme, Strict Priority (SP) or ATM CoS
INT radBridgeIPXForwarding	1.3.6.1.4.1.164.4.1.5.1.1	INTEGER	read-write	The indication of whether this entity is acting as an IPX gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IPX gateways forward datagrams. IPX hosts do not. Note that changing this parameter requiers RESET of the router.
INT radBridgeIPXRipForwardType	1.3.6.1.4.1.164.4.1.5.2.6.1.9	INTEGER	read-write	The type of route. Note that local(2) refers to a route for which the next hop is the final destination; remote(3) refers to a route for which the next hop is not the final destination.
INT radBridgeIPXRipPolicy	1.3.6.1.4.1.164.4.1.5.2.6.1.2	INTEGER	read-only	A value specifying the precidence of the route. A value of zero means that the route is the best route, a value of one means that the route is the second best route and so on.
INT radBridgeIPXRipValueStatus	1.3.6.1.4.1.164.4.1.5.2.6.1.8	INTEGER	read-write	The entry status value; whether the entry is permanent (added statically), reachable or unreachable. In the latter two cases it would be added by RIP. A semiDynamic entry is an entry enterd manualy by the user and can be updated by the router.
INT radBridgeIPXSapStatus	1.3.6.1.4.1.164.4.1.5.3.6.1.9	INTEGER	read-write	The status of the entry.
INT radBridgeMaskCond1	1.3.6.1.4.1.164.4.1.3.1.9	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that matches the content of radBridgeMaskPat1. false - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that does not match the content of radBridgeMaskPat1.
INT radBridgeMaskCond2	1.3.6.1.4.1.164.4.1.3.1.14	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that matches the content of radBridgeMaskPat2. false - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that does not match the content of radBridgeMaskPat2.
INT radBridgeMaskCond3	1.3.6.1.4.1.164.4.1.3.1.19	INTEGER	read-write	Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that matches the content of radBridgeMaskPat3 false - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that does not match the content of radBridgeMaskPat3.
INT radBridgeMaskDest	1.3.6.1.4.1.164.4.1.3.1.4	INTEGER	read-write	Specifies the type of destination address carried by the frame to which the mask will be applied. Unassigned-condition deactivates the mask entry.
INT radBridgeMaskFrom1	1.3.6.1.4.1.164.4.1.3.1.7	INTEGER	read-write	Offset base of radBridgeMaskPat1 within the frame. Net can be in some cases the data start point.
INT radBridgeMaskFrom2	1.3.6.1.4.1.164.4.1.3.1.12	INTEGER	read-write	Offset base of radBridgeMaskPat2 within the frame. Net can be in some cases the data start point.
INT radBridgeMaskFrom3	1.3.6.1.4.1.164.4.1.3.1.17	INTEGER	read-write	Offset base of radBridgeMaskPat3 within the frame. Net can be in some cases the data start point.
INT radBridgeMaskOper	1.3.6.1.4.1.164.4.1.3.1.20	INTEGER	read-write	The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list.
INT radBridgeMaskType	1.3.6.1.4.1.164.4.1.3.1.1	INTEGER	read-only	Defines the type of mask entry.
INT radBridgeMngFlow	1.3.6.1.4.1.164.4.1.9.6	INTEGER	read-write	This variable defines whether the Management Flow is passed through the bridge (enable) or not (disable).
INT radBridgePortBaseVlanMng	1.3.6.1.4.1.164.4.1.8.1.1.7	INTEGER	read-create	This object allows user to enable/disable management traffic on this VLAN. disable - only non-management data is allowed. enable - mixture of management traffic 0with other types of data is allowed.
INT radBridgePortCnfgDot1x	1.3.6.1.4.1.164.4.1.13.1.1.11	INTEGER	read-write	This feature is currently supported via the variable ethIfTable.ethDot1xEnable. Determnines if the Port-Based Network Access Protocol (IEEE-802.1x)is enabled for the bridge Port.
INT radBridgePortCnfgMcastMode	1.3.6.1.4.1.164.4.1.13.1.1.5	INTEGER	read-write	This object indicates this Bridge Port's Multicast Mode: flooding (1) - flood multicast MAC addresses forwarding (2) - forward multicast MAC addresses to the subnet indicated.
INT radBridgePortCnfgMngFlow	1.3.6.1.4.1.164.4.1.13.1.1.4	INTEGER	read-write	This object indicates whether this Bridge Port is dedicated for management flow.
INT radBridgeSplitHorizon	1.3.6.1.4.1.164.4.1.9.4.1.7	INTEGER	read-write	This object configure 'split horizon' switching between bridge Ports. - disable - normal (VLAN aware) bridge behavior. - enable - all packets, regardless their VLAN, coming from user side are blocked from being switched back to other user side bridge ports. - vlanBased - split horizon behavior is applicable only for specific VLANs, according to radBridgeDot1qVlanSplitHorizon.
INT radBridgeStpCnfgStpVersion	1.3.6.1.4.1.164.4.1.11.1.1.7	INTEGER	read-write	This object determines the STP version used: stp - usual Spanning Tree Protocol. rstp - Rapid Spanning Tree Protocol.
INT radDot1qPortCopyOriginVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.2	INTEGER	read-write	This object indicates whether use the original VLAN Priority of the frame, as the priority of the VLAN added by this port.
INT radDot1qPortEgressTagHandling	1.3.6.1.4.1.164.4.1.9.3.1.5	INTEGER	read-write	This object indicates how is the Egress VLAN Tag processed. It is mainly for use with Double Tagging.
INT radDot1qPortIngressTagHandling	1.3.6.1.4.1.164.4.1.9.3.1.6	INTEGER	read-write	This object indicates how is the Ingress VLAN Tag processed. It is mainly for use with Double Tagging.
INT radDot1qPortReplaceVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.7	INTEGER	read-write	This object indicates whether for each received tagged frame on this Bridge Port - VLAN Priority will be replaced by another Priority. no(2) = no repacement yes(3) = VLAN Priority will be replaced For Egate-100: When value is 'yes', the original Priority is replaced by the Default Priority.
INT radDot1qPortStacking	1.3.6.1.4.1.164.4.1.9.3.1.1	INTEGER	read-write	This object indicates the port stacking operation: unmodify (2) = Do not add Tag. tag (3) = Add Tag to Untagged Frames. stack (4) = Add Tag to all Frames.
INT radDot1qPortTagStripping	1.3.6.1.4.1.164.4.1.9.3.1.4	INTEGER	read-write	This object indicates whether remove a tag from the frame on this port, frame with double tag will remain with one tag and frame with one tag will remain untagged.
INT radDot1qPortVlanCnodeLevel1Agent	1.3.6.1.4.1.164.4.1.9.3.1.9	INTEGER	read-write	Specify if a Level 1 cNode agent is enabled or not for the bridge port.
INT radMdFormat	1.3.6.1.4.1.164.3.1.6.1.3.3.1.2	INTEGER	read-create	The type (and thereby format) of the Maintenance Domain Name.
INT radMepCcInterval	1.3.6.1.4.1.164.3.1.6.1.3.1.1.19	INTEGER	read-create	Indicates the interval at which CCMs are sent by a MEP Valid only if radMepOamMode = initiate(4).
INT radMepCcStat	1.3.6.1.4.1.164.3.1.6.1.3.5.1.3	INTEGER	read-only	This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpectedMep -A MEP detects an Unexpected MEP condition when a CCM frame arrives with the correct MEG level, the correct MEG ID, but an unexpected MEP ID, which includes the MEP's own MEP ID. unexpectedMeLevel - A MEP detects an Unexpected MEG Level condition when a CCM frame arrives with incorrect MEG Level. Incorrect MEG Level is less than the MEP's own MEG level. unexpectedPeriod - A MEP detects an Unexpected Period condition when a CCM frame arrives with a correct MEG level. a correct MEG ID, a correct MEP ID, but with the Period field value different from the MEP's own CCM transmission period. rdi - A MEP detects RDI when it receives a CCM frame with the RDI field set.
INT radMepCcStatus	1.3.6.1.4.1.164.3.1.6.1.3.1.1.13	INTEGER	read-only	This object indicates the Continuity Check (CC) status.
INT radMepContinuityVerMode	1.3.6.1.4.1.164.3.1.6.1.3.1.1.8	INTEGER	read-create	This object determines the OAM behavior of the MEP: disabled - no CC is done cc_based - CC is done based on incoming messages lb_based - CC is done based on loopback messages.
INT radMepLtrEgress	1.3.6.1.4.1.164.3.1.6.1.3.4.1.8	INTEGER	read-only	The value returned in the Egress Action Field of the LTM. The value egrNoTlv(1) indicates that no Reply Egress TLV was returned in the LTM. 802.1ag clauses 12.14.7.5.3:o and 20.36.2.10
INT radMepLtrIngress	1.3.6.1.4.1.164.3.1.6.1.3.4.1.5	INTEGER	read-only	The value returned in the Ingress Action Field of the LTM. ingNoTlv - no Reply Ingress TLV was returned in the LTM. ingOK - the target data frame would be passed through to the MAC Relay Entity. ingDown - the Bridge Port's MAC_Operational parameter is false. ingBlocked - the target data frame would not be forwarded if received on this port. ingVid - the ingress port is not in the members of the LTM's VID, and ingress filtering is enabled, so the target data frame would be filtered by the ingress filtering. 802.1ag clauses 12.14.7.5.3:k and 20.36.2.6
INT radMepLtrRelay	1.3.6.1.4.1.164.3.1.6.1.3.4.1.4	INTEGER	read-only	The value returned in the Relay Action field: rlyHit - the LTM reached an MP whose MAC address matches the target MAC address. rlyFdb - the Egress Port was determined by consulting the Filtering Database. rlyMpdb - the Egress Port was determined by consulting the MIP CCM Database. 802.1ag clauses 12.14.7.5.3:g and 20.36.2.5
INT radMepMaFormat	1.3.6.1.4.1.164.3.1.6.1.3.1.1.16	INTEGER	read-create	The type (and thereby format) of the Maintenance Association Name.
INT radMepOamDestAddrType	1.3.6.1.4.1.164.3.1.6.1.3.1.1.10	INTEGER	read-create	This object determines if the OAM messages are sent to user defined unicast address, or to RAD proprietary multicast address.
INT radMepOamMode	1.3.6.1.4.1.164.3.1.6.1.3.1.1.7	INTEGER	read-create	This object determines the OAM mode of the MEP: disabled - no CC is initiated nor responded initiate - the device initiates and responds to CC react - the device does not initiate a CC, but responds to CC.
INT radMepOamProtocol	1.3.6.1.4.1.164.3.1.6.1.3.1.1.14	INTEGER	read-create	Determines whether to use proprietary OAM mechanism, or to use the standard (IEEE 802.1ag, ITU-T Y.1731).
INT radMepTransmitLbmDestIsMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.22	INTEGER	read-create	yes (3) indicates that MEPID of the target MEP is used for loopback transmission. no (2) indicates that unicast destination MAC address of the target MEP is used. 802.1ag clause 12.14.7.3.2:b.
INT radMepTransmitLbmVlanDropEnable	1.3.6.1.4.1.164.3.1.6.1.3.1.1.25	INTEGER	read-create	Drop Enable bit to be used in the VLAN tag, if present, in the transmitted frame. 802.1ag clause 12.14.7.3.2:e
INT radMepTransmitLtmActivationCmd	1.3.6.1.4.1.164.3.1.6.1.3.1.1.33	INTEGER	read-create	Activation command for starting Loop Trace. Set will be always to 'on' value. After operation was finished, Agent will turn the value to 'off'.
INT radMepTransmitLtmTargetIsMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.31	INTEGER	read-create	yes (3) indicates that MEPID of the target MEP is used for Linktrace transmission. no (2) indicates that unicast destination MAC address of the target MEP is used. 802.1ag clause 12.14.7.4.2:c.
INT ripSapIfConfMode	1.3.6.1.4.1.164.11.7.2.3.4.1.2	INTEGER	read-create	The ifIndex RIP/SAP mode.
INT schedWeekInMonth	1.3.6.1.4.1.164.6.2.14.5.1.2	INTEGER	read-create	The week in month (schedMonth) during which the scheduled action should take place.
INT serviceStatDirection	1.3.6.1.4.1.164.6.3.8.1.1	INTEGER	not-accessible	The direction in wich the measurement is taken.
INT srvResetStatsCmd	1.3.6.1.4.1.164.6.3.8.1.18	INTEGER	read-create	Reset statistic counters of the service.
INT sysBufferAlrClearCmd	1.3.6.1.4.1.164.3.3.1.5.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2).
INT sysBufferAlrSlot	1.3.6.1.4.1.164.3.3.1.5.1.1.4	INTEGER	read-only	The slot number this alarm refers to. When the alarm refers to a system function OR the DACS agent is a stand-alone unit, the value will be 'notApplicable(255)'. local/remote - for OP-4 device.
INT sysBufferAlrState	1.3.6.1.4.1.164.3.3.1.5.1.1.3	INTEGER	read-only	This object indicates the alarm type. minor/major/warning/critical - indicates appearance of the problem and the type. event - indicates occurence of an event. off - indicates disappearance of an alarm.
INT sysCAutoConfigEnable	1.3.6.1.4.1.164.3.3.1.6.2.1.5	INTEGER	read-write	This object enables user to enable/disable activating the Auto Configuration. When Auto Configuration is activated, the device learns its configuration Automatically from the Net it is connected to.
INT sysCBuPrimaryPort	1.3.6.1.4.1.164.3.3.1.6.2.1.7	INTEGER	read-write	This object enables the user to configure a Backup mechanism. If a backup mechanism exists, it is possible to configure the primary port. The traffic will flow via the primary port when the port functionality is OK. In Vmux-2100 device the backup mechanism is relevant for the Main Board only. The primary port can be the E1/T1/Serial port or the ETH port.
INT sysCBuRecMode	1.3.6.1.4.1.164.3.3.1.6.2.1.10	INTEGER	read-write	Recovery Mode. This object determines if after recovery of the Primary Link (used in Vmux) it will become on-line again or not: auto - automatic. In this case, the failed Link will become on-line again after recovery, automatically. manual - In this case, the failed Link will not become on-line again after recovery but user can manually flip to this Link.
INT sysCClkSrcIdx	1.3.6.1.4.1.164.3.3.1.6.1.1.2	INTEGER	read-only	An index in the table. There are only two entries in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
INT sysCClkSrcMode	1.3.6.1.4.1.164.3.3.1.6.1.1.3	INTEGER	read-write	This entry indicates the source the nodal timing is locked to. none - is an invalid option for Master clock. internal - is an invalid option for Fallback clock . station - is an invalid option for a stand-alone unit. lbt - loop-back timing ntr - Network Time Reference adaptive - clock locking is achieved by altering the clock according to the data load system - irrelevant when sysCClkCnfgIdx refers to System Clock. sSubSystem - SONET/SDH Sub System. recovered - clock recovery. notApplicable - for ML source of Kmux or ML Timing combinations when Master/Fallback clock are not applicable.
INT sysCClkSsmBased	1.3.6.1.4.1.164.3.3.1.6.1.1.10	INTEGER	read-write	This parameter indicates whether clock source will be selected based on receive clock quality, indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging). It is relevant only for sysCClkSrcIdx=master. When the value is Yes, sysCClkSrcMode must be notApplicable.
INT sysCClkSSubsystemSlot	1.3.6.1.4.1.164.3.3.1.6.1.1.11	INTEGER	read-write	This entry indicates the Slot from which the S Subsytem Source will be taken. The value will be applicable only when the sysCClkSrcMode is 'sSubsystem'.
INT sysCClkStationCableMode	1.3.6.1.4.1.164.3.3.1.6.1.1.8	INTEGER	read-write	This parameter indicates whether both Station clocks get their clock from the same source (Y Cable)or each one get its clock independently. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkStationFreq	1.3.6.1.4.1.164.3.3.1.6.1.1.5	INTEGER	read-write	This entry indicates the frequency of the station clock when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkStationIf	1.3.6.1.4.1.164.3.3.1.6.1.1.7	INTEGER	read-write	This entry indicates the electrical interface connected to the station clock, when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCClkStationOutState	1.3.6.1.4.1.164.3.3.1.6.1.1.9	INTEGER	read-write	This parameter indicates whether station clock can send its clock to another device. The value will be applicable only when the sysCClkSrcMode is 'station'.
INT sysCEnableLanOverTdm	1.3.6.1.4.1.164.3.3.1.6.2.1.8	INTEGER	read-write	This object enables/disables transferring traffic from the LAN port to the TDM port. It is possible to enable only part of the traffic on the TDM port for security reasons or in order to minimize the bandwidth .
INT sysCIntTsAllocMode	1.3.6.1.4.1.164.3.3.1.6.2.1.6	INTEGER	read-write	This object enables user to select the mode of Internal TS Allocation. static - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). This number will be allocated to the ports, so that if number of connected TSs will grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports. dynamic- TS allocation is done dynamically according to the connected TSs. No future reservations are done. This mode may cause data disruption on other ports/slots if user will want to change the number of connected TSs for a Dynamic card port. staticOneToOne - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). In addition, the TSs themselves cannot be higher than this defined Maximum (e.g if Maximum TSs=5 user cannot selects TSs higher than 5). This mode ensures that if number of TSs grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports AND for the selected port itself. Default=static(2).
INT sysCIsdnFormat	1.3.6.1.4.1.164.3.3.1.6.2.1.3	INTEGER	read-write	ISDN format. This parameter controls the operation mode of the ISDN ports. te - ISDN timing is derived from the signal received from the equipment it is connected to. nt - timing of the transmit path is locked to the nodal timing source. notApplicable - for agents that do not support this feature.
INT sysCMatrixMode	1.3.6.1.4.1.164.3.3.1.6.2.1.2	INTEGER	read-write	Indicates the TS Matrix Mode: bidirectional - TS Assignment Matrix is symmetric. unidirectional - TS Assignment Matrix can be asymmetric. notApplicable - for agents that do not support this feature.
INT sysCRdnHwSwFlip	1.3.6.1.4.1.164.3.3.1.6.3.1.9	INTEGER	read-create	HW or SW decision for Redundancy Flip. This object is applicable only for sysCRdnMode=singleSlotProtection. HW - decision is by I/O card SW - decision is by CL SW.
INT sysCRdnMode	1.3.6.1.4.1.164.3.3.1.6.3.1.6	INTEGER	read-create	Redundancy Mode. DXC supports: yCable(3), singleSlotProtection(6) and dualCableParallelTx(4) MP supports: yCable(3), dualCableParallelTx(4), onePlusOne(7) and oneToOne(8). (dualCableAIS and backup were planned for MP but were not implemented). backup - will be used when a port is backup of more than one port. IPmux: onePlusOne(7) and oneToOne(8) are used for Bundle redundancy.
INT sysCRdnOnline	1.3.6.1.4.1.164.3.3.1.6.3.1.11	INTEGER	read-only	Status - who is the Online (current) Redundancy Slot/Port. This object shows only the Online Slot/Port regarding the Redundancy. mdlSActivity or prtGenActiveStatus of the same Slot/Port may be Offline.
INT sysCRdnPrimePriority	1.3.6.1.4.1.164.3.3.1.6.3.1.19	INTEGER	read-create	The Primary port priority. In ETX2xx/2xxA: When selecting sysCRdnMode = manual (10), this parameter determines the forced active port: low - means that the secondary port is selected to be active high - means that the primary port is selected to be active.
INT sysCRdnPrimeSlot	1.3.6.1.4.1.164.3.3.1.6.3.1.2	INTEGER	read-only	The slot number of the Primary card of Redundancy. The Primary card should be the card that user wishes to be the online card (usually the more important one). For some Redundancy modes the importance of the redundant cards/ports is the same.
INT sysCRdnRecMode	1.3.6.1.4.1.164.3.3.1.6.3.1.7	INTEGER	read-create	Recovery Mode. This object determines if after recovery of the failed Primary card/port it will become on-line again or not: auto - automatic . In this case, the failed card/port will become on-line again after recovery, automatically. manual - In this case, the failed card/port will not become on-line again after recovery. But, user can manually flip to this card/port. nonRevertive - same as manual, but here user CANNOT manually flip to this card/port. It will become on-line again, only if the Secondary/Backup card/port will fail.
INT sysCRdnSecPriority	1.3.6.1.4.1.164.3.3.1.6.3.1.20	INTEGER	read-create	The Secondary port priority.
INT sysCRdnSecSlot	1.3.6.1.4.1.164.3.3.1.6.3.1.4	INTEGER	read-create	The slot number of the Secondary card of Redundancy matching the Primary slot.
INT sysCRdnSwitchingMode	1.3.6.1.4.1.164.3.3.1.6.3.1.12	INTEGER	read-create	This object defines which Self Healing Ring (SHR) SDH ring is used: Uni Directional or BiDirectional. The type of the ring is defined according to the direction of traffic flow under normal working conditions. In Bi Directional ring, the duplex traffic is on the same path and transverses the same set of nodes for both directions of transmission. In Uni Directional ring, the duplex traffic travels over opposite path (per direction) and all the node of the ring are involved. For Uni Directional SHR Protection Switching (Single Ended Switching) is controlled by one node of the SDH ring, and does not require a protocol. For Bi Directional SHR Protection Switching (Dual Ended switching) is controlled by some nodes of the ring and requires a protocol
INT sysCRoutingOnEth	1.3.6.1.4.1.164.3.3.1.6.2.1.4	INTEGER	read-write	Mng Routing Protocol on the online CL Ethernet port, or on device Ethernet port dedicated for mangement.
INT sysDbaseFlipActivation	1.3.6.1.4.1.164.3.3.1.7.4.1.3	INTEGER	read-write	This attribute indicates if the Dbase flip will be activated at the time specified for this configuration (enable) or not (disable). No more than one flip should be enabled for the same time.
INT sysDbaseSanityCheckCmd	1.3.6.1.4.1.164.3.3.1.7.1	INTEGER	read-write	Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion, the value will automatically change to off(2).
INT sysDclActiveCl	1.3.6.1.4.1.164.3.3.1.2.2.1.1.3	INTEGER	read-write	Active desired DCL. When 'auto' is selected, the system automatically selects the active DCL.
INT sysDclConfigDownloadSrc	1.3.6.1.4.1.164.3.3.1.2.2.1.1.8	INTEGER	read-write	In case of mismatch between the 2 CL card's configuration, the user can decide which card has the suitable configuration. The selected configuration will be downloaded from card A to card B if the value is dclA(2) or from card B to card A if the value is dclB(3). off(1) is used by part of the devices. In this case, after operation ends - value should be automatically set to off(1), which is the default state.
INT sysDclCopyDbCmd	1.3.6.1.4.1.164.3.3.1.2.2.3.1.2	INTEGER	read-write	When this command is sent to the agent, on(3), the Database specified (Db Idx), will be copied from the Offline Dcl to the Online Dcl. Afterwards the value of this object will automatically change to off(2).
INT sysDclFlipCmd	1.3.6.1.4.1.164.3.3.1.2.2.4	INTEGER	read-write	When the 'flip(3)' command is received by Agent, it will flip (switch) between Offline Dcl and Online Dcl cards. Afterwards the value of this object will automatically change to off(2).
INT sysDclFlipUponStnClk	1.3.6.1.4.1.164.3.3.1.2.2.1.1.5	INTEGER	read-write	This object allows user to decide (yes/no) if Agent should Flip from one DCL card to another, when there is Station Clock Fail in the Online DCL card.
INT sysDclOnline	1.3.6.1.4.1.164.3.3.1.2.2.2	INTEGER	read-only	The active Dcl card of the agent.
INT sysDclRedundancy	1.3.6.1.4.1.164.3.3.1.2.2.1.1.2	INTEGER	read-write	DCL redundancy desired state.
INT sysDclSwDownloadSrc	1.3.6.1.4.1.164.3.3.1.2.2.1.1.9	INTEGER	read-write	In case of mismatch between the 2 CL card's software, the user can decide which card has the suitable SW. The selected SW will be downloaded from card A to card B if the value is dclA(2) or from card B to card A if the value is dclB(3). off(1) is used by part of the devices. In this case, after operation ends - value should be automatically set to off(1), which is the default state.
INT sysSaBuActivePort	1.3.6.1.4.1.164.3.3.1.1.6	INTEGER	read-only	This object shows through which port the traffic is flowing (the current Active Port) when the Backup mechanism exists. When No Backup exists in the device, the value should be: notApplicable(1).
INT sysSAlarmInvert	1.3.6.1.4.1.164.3.3.1.4.1.1.5	INTEGER	read-only	Alarm Invert is : on/off.
INT sysSAlarmMask	1.3.6.1.4.1.164.3.3.1.4.1.1.4	INTEGER	read-only	Alarm Mask is : on/off.
INT sysSAlarmOnOff	1.3.6.1.4.1.164.3.3.1.4.1.1.6	INTEGER	read-only	Alarm state is : on/off.
INT sysSAlrClearAllCmd	1.3.6.1.4.1.164.3.3.1.4.3	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on all levels alarms . Upon completion, the value will automatically change to off(2).
INT sysSAlrClearCmd	1.3.6.1.4.1.164.3.3.1.4.2	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the system level alarms . Upon completion, the value will automatically change to off(2).
INT sysSAlrDataUpdateCmd	1.3.6.1.4.1.164.3.3.1.4.6	INTEGER	read-write	on(3) - will cause Update of the Alarms Severity, Attributes and Report tables. off(2) - Upon completion, the value will automatically change to off(2).
INT sysSAlrMaskAll	1.3.6.1.4.1.164.3.3.1.4.4	INTEGER	read-write	on(3) - will cause masking of all the system level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all system level alarms except those masked via the sysSAlrMask.
INT sysSAlrState	1.3.6.1.4.1.164.3.3.1.4.1.1.3	INTEGER	read-only	This object indicates the alarm Severity.
INT sysSAlrStatus	1.3.6.1.4.1.164.3.3.1.3.8	INTEGER	read-only	Indicates the current alarm state only for system level. This object will be : - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT sysSAlrStatusAll	1.3.6.1.4.1.164.3.3.1.3.9	INTEGER	read-only	Indicates the current alarm state including all levels: system, card, port. - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
INT sysSBusStatus	1.3.6.1.4.1.164.3.3.1.3.21.1.2	INTEGER	read-only	The Status of sysSBusPortIdx. free - not used physical - captured by the port of the card physically installed virtual - captured virtually by another port. Example: DIM port (by Destination) or by Transparent T3/E3 port.
INT sysSClkSrc	1.3.6.1.4.1.164.3.3.1.3.7	INTEGER	read-only	This entry indicates the source of the system clock.
INT sysSDateFormat	1.3.6.1.4.1.164.3.3.1.3.1	INTEGER	read-write	This object indicates the date and time format used for the sysSDateAndTimeCmd and for the alarm buffer report.
INT sysSEditBy	1.3.6.1.4.1.164.3.3.1.3.6	INTEGER	read-only	This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after a load operation.
INT sysSErrType	1.3.6.1.4.1.164.3.3.1.3.13.1.1	INTEGER	read-only	The errors are recorded in the agent, in two separate lists, according to their type: error or warning.
INT sysSInvertedAlr	1.3.6.1.4.1.164.3.3.1.3.17	INTEGER	read-only	Indicates if there is any Inverted alarm at any level of the system (sys, card, port). notApplicable - for agents that do not support this object.
INT sysSRdnEnforcedChannel	1.3.6.1.4.1.164.3.3.1.3.22.1.1	INTEGER	read-write	This is a command to override all switching considerations and enforce use of primary/ secondary connection only. noEnforcement - cancels the state of override and goes back to usual switching considerations. Default = noEnforcement(2).
INT sysSRdnFlipSlot	1.3.6.1.4.1.164.3.3.1.3.18.1.2	INTEGER	read-only	The slot number from which Flip was performed.
INT sysSRdnFlipTableClearCmd	1.3.6.1.4.1.164.3.3.1.3.19	INTEGER	read-write	This command, when Set to 'on', clears the Redundancy Flip table (sysSRdnFlipTable). After clear is performed, the agent will turn the value to 'off' automatically.
INT sysSRdnLockFlip	1.3.6.1.4.1.164.3.3.1.3.22.1.2	INTEGER	read-write	This is a command to lock the Redundancy flip for this redundancy couple. Default = off(2).
INT sysSRdnManualFlip	1.3.6.1.4.1.164.3.3.1.3.22.1.3	INTEGER	read-write	This is a command to move to manual Redundancy flip mode for this redundancy couple. Default = off(2).
INT sysSRelayState	1.3.6.1.4.1.164.3.3.1.3.16	INTEGER	read-only	Indicates the current state of the alarm relay. notApplicable - for agents that do not support this object.
INT sysSSanityCheckStatus	1.3.6.1.4.1.164.3.3.1.3.11	INTEGER	read-only	Upon completion of the Sanity Check process on the TmpCnfg this object will be set to: - fail(2): when there is at least one error (which is not just a warning) encountered otherwise, - warning(3): when there are only warnings otherwise, - ok(4). The value should be unknown(1), if the TmpCnfg was changed after the last Sanity check.
INT sysSTestStatus	1.3.6.1.4.1.164.3.3.1.3.10	INTEGER	read-only	Indicates the current test status (for all levels: system, card, port). This attribute will be set to: - on(3): when there is at least one test in progress on the system/card/port otherwise the value will be off(2).
INT systemClearTablesCmd	1.3.6.1.4.1.164.6.2.17	INTEGER	read-write	tempCnfgTables - Set RowStatus = destroy for all entries of some tables having RowStatus object, for temporary configuration only! (255). For the relevant tables, see product's specification. This object should be used by WAN product applications before performing the Update operation, in order to clear old entries of these tables. For MP-104/204 the entries will be destroyed for cnfg=1. off - agent will automatically change to this value, after performing the command.
INT systemNtpCmd	1.3.6.1.4.1.164.6.2.14.4.6	INTEGER	read-write	This variable represents NTP possible commands. After the Agent accepts a command, it will automatically change the value to off(2).
INT systemNtpMode	1.3.6.1.4.1.164.6.2.14.4.1	INTEGER	read-write	This variable represents the NTP Mode.
INT systemOamDescrCCDirection	1.3.6.1.4.1.164.6.2.36.2.1.4	INTEGER	read-create	OAM Continuity Check function mode. both(2) - Agent sends OAM CC cells and checks received OAM CC cells. none(3) - Agent does not send and does not check received OAM CC cells. source(4)- Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells.
INT systemOamDescrLoopbackOperation	1.3.6.1.4.1.164.6.2.36.2.1.5	INTEGER	read-create	The OAM Loopback function mode. off(2) - Stop sending loopback OAM cells. on(3) - Start loopback OAM cells.
INT systemOamDescrMode	1.3.6.1.4.1.164.6.2.36.2.1.3	INTEGER	read-create	The OAM Mode of the Descriptor.
INT systemOamLinkCheck	1.3.6.1.4.1.164.6.2.36.1.1.4	INTEGER	read-write	This MIB object determines whether continuous connectivity Link checks will be performed by the device for uplinks. For Vmux-2100: enable (3) value can be set upon device installation. In this case, TDM Link Connectivity checks can be performed even before the user configures the Links of the device.If the value is enable (3) and there is no connection with the remote side, the Test LED will blink on the Main Board Module.
INT systemPsHotSwap	1.3.6.1.4.1.164.6.2.25.1.5	INTEGER	read-only	Is PS unit hot swap or fixed.
INT systemPsStatus	1.3.6.1.4.1.164.6.2.25.1.4	INTEGER	read-only	The Status of the PS unit.
INT systemPsType	1.3.6.1.4.1.164.6.2.25.1.3	INTEGER	read-only	The type of PS, for a stand-alone product. acDc - PS that supports both AC and DC. acPF - Power Feeding (phantom) box that is feeding another box by external AC. dcPF - Power Feeding (phantom) box that is feeding another box by external DC.
INT systemReset	1.3.6.1.4.1.164.6.2.13	INTEGER	read-write	Reset action to be performed on the system. - resetMapping - reset SDH/SONET mapping to default for all SDH/SONET links. - resetStandby(6) - can be used only by devices with redundancy on MAIN/CL.
INT systemResetAllStatsCmd	1.3.6.1.4.1.164.6.2.16	INTEGER	read-write	Reset statistics of all ports and connections of the device.
INT systemSaveAndResetAllStatsCmd	1.3.6.1.4.1.164.6.2.23	INTEGER	read-write	on - a command to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. off - agent will automatically change to this value, after performing the command.
INT systemVoiceCoderAndRate	1.3.6.1.4.1.164.3.1.2.12.1.1.7	INTEGER	read-write	This object indicates the Coder and Rate for the Voice Compression.
INT systemVoiceCoderCoderAndRate	1.3.6.1.4.1.164.3.1.2.12.2.1.3	INTEGER	read-write	This object indicates the Coder and Rate for the Voice Compression.
INT systemVoiceDtmfRelayMethod	1.3.6.1.4.1.164.3.1.2.12.1.1.10	INTEGER	read-write	This object indicates the DTMF Relay Method that is used to transmit DTMF tones. rfc2833(1) - inband DTMF relay according to RFC-2833. sipInfo(2) - out of band DTMF relay using SIP INFO method.
INT systemVoiceDtmfRelayPayloadTypeNeg	1.3.6.1.4.1.164.3.1.2.12.1.1.12	INTEGER	read-write	This object indicates whether Payload Type Negotiation is used (according to RFC-2833) or not. It is relevant only when DTMF Relay Method is RFC-2833.
INT systemVoiceEchoCanceler	1.3.6.1.4.1.164.3.1.2.12.1.1.8	INTEGER	read-write	This object indicates the Echo Canceler activation.
INT systemVoiceFaxRate	1.3.6.1.4.1.164.3.1.2.12.1.1.5	INTEGER	read-write	This object indicates the Fax Rate limit. It is irrelevant when Fax support is NA or disabled.
INT systemVoiceFaxSupport	1.3.6.1.4.1.164.3.1.2.12.1.1.4	INTEGER	read-write	This object allows the user to Disable/Enable Fax support.
INT systemVoiceModemSupport	1.3.6.1.4.1.164.3.1.2.12.1.1.6	INTEGER	read-write	This object allows the user to Disable/Enable Modem support.
INT systemVoiceNationalTone	1.3.6.1.4.1.164.3.1.2.12.1.1.2	INTEGER	read-write	Tone Characteristics (Amplitude, Frequency, delays etc.). These characteristics are defined according to the country.
INT tftpStatus	1.3.6.1.4.1.164.6.2.12.6	INTEGER	read-write	Status of tftp session. When a session ended with success, the tftpStatus should be endedOk(6). Before restarting a tftp session, the NMS should set the tftpStatus to noOp(2). That's the reason of MAX-ACCESS read-write to this field.
INT wfqSchedulingMode	1.3.6.1.4.1.164.6.3.1.1.1.7	INTEGER	read-create	This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme or priority Queue (Strict Priority).
INT wrAutoLearnLanIpxNets	1.3.6.1.4.1.164.11.7.2.3.1	INTEGER	read-write	Activating (disable/enable) the auto-learn operation.
INT wrBraodcastCtrlCmd	1.3.6.1.4.1.164.11.7.2.1.1	INTEGER	read-write	This parameter is a command to the webranger CPU. It enables blocking or forwarding broadcast frames, which may cause a trigger to a connection. block (1) - blocks the broadcast frames. forward (2) - forwards the broadcast frames. blockLinkPropagation (3) - blocks the broadcast frames to the links, tx to the LAN.
INT wrDhcpAction	1.3.6.1.4.1.164.11.7.2.2.1.1	INTEGER	read-write	Activating (disable/enable) DHCP server operation. Since DHCP Server and DHCP Relay cannot reside in same device, DHCP Relay may be enabled (per interface), only if server action is disabled. For some devices, this object is used in order to enable/disable the DHCP Client. See device SDS.
INT wrDhcpInterface	1.3.6.1.4.1.164.11.7.2.2.1.2.1.7	INTEGER	read-create	The IP addresse allocation is done according to the interface type from which the DHCP request arrives.
INT wrDhcpPort	1.3.6.1.4.1.164.11.7.2.2.1.5	INTEGER	read-write	This parameter defines the port that DHCP flow will be actiavted.
INT wrDNSRelayAction	1.3.6.1.4.1.164.11.7.2.2.2.1	INTEGER	read-write	When Enabled, device will act as a DNS Relay: whenever the device receives a DNS request from its host, it will forward it to the DNS server as if the request was initiated by the device itself. The reply from the DNS server is forwarded by the device to the host as if the device was answering the request.
INT wrFrCllmMessages	1.3.6.1.4.1.164.11.7.2.4.5.1.2	INTEGER	read-write	This parameter enables/disables the Webranger to Tx/Rx CLLM (Consolidated Link Layer Management) messages via DLCI 1023. The CLLM messages are link layer control messages. They can be used for example in cases of congestion. The CLLM message contains a code for cause of congestion and list of all DLCIs that should act to reduce data transmission.
INT wrFrDlciLearningMode	1.3.6.1.4.1.164.11.7.2.4.5.1.1	INTEGER	read-write	This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol for the current interface. off - the WR will read the user's configuration for this interface. on - the WR will begin self learning of the current interface's maintanance protocol and DLCIs.
INT wrFrSelfLearningMode	1.3.6.1.4.1.164.11.7.2.1.2	INTEGER	read-write	This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol. off - will get the configuration by setting it. on - disables configuration and start self learning.
INT wrGratuitousArp	1.3.6.1.4.1.164.11.7.2.1.3	INTEGER	read-write	This parameter enables/disables the Gratuitous ARP feature. When enabled, the feature means: when receiving ARP with sender's Source IP Address that already exists in the ARP table - replace MAC Address with sender's Source MAC Address.
INT wrLanBridgeRouterMode	1.3.6.1.4.1.164.11.7.2.4.3.1.2	INTEGER	read-write	This parameter indicates whether the link is Bridge or Router and specifies the Router's type.
INT wrLanIfState	1.3.6.1.4.1.164.11.7.2.4.3.1.3	INTEGER	read-write	The LAN is disabled or enabled. For LAN 2 it can be also 'redundancy'.
INT wrLanIpxFrameType	1.3.6.1.4.1.164.11.7.2.3.2.1.2	INTEGER	read-only	Frame Type
INT wrSyncClkMode	1.3.6.1.4.1.164.11.7.2.4.4.1.2	INTEGER	read-write	Clock Mode.
INT wrSyncClkRate	1.3.6.1.4.1.164.11.7.2.4.4.1.3	INTEGER	read-write	Clock Rate in. Rate can be changed if Clock Mode is Program only.
INT xcAdminStatus	1.3.6.1.4.1.164.6.2.31.1.8	INTEGER	read-create	The desired administrative status of this bi-directional cross-connect.
INT xcAttachedIfType	1.3.6.1.4.1.164.6.2.31.1.10	INTEGER	read-only	This object indicates if the specific VCC is already attached to any interface, and indicates the type of the interface. This object's purpose is to ease the checking to the NMS. notApplicable - used for entries that are not LAN (as HDLC), or when the VCC was attached to a bridge, or when this parameter is irrelevant. free - the LAN VCC wasn't attached yet to any router interface. routerAtm - attached to an ATM router interface. lis - attached to a LIS interface.
INT xcOperStatus	1.3.6.1.4.1.164.6.2.31.1.9	INTEGER	read-only	The operational status of this bi-directional cross-connect.
Integer32 (855)
I32 agnAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.2.3.3.1.2	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
I32 agnAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.2.3.3.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnAlrBufCmprAlarmIdx	1.3.6.1.4.1.164.3.1.2.3.4.1.2	Integer32	read-only	A unique number to identify an entry in the history alarms buffer of the agent.
I32 agnAlrBufCmprVersion	1.3.6.1.4.1.164.3.1.2.3.4.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnCBuMlCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.12.1.1	Integer32	not-accessible	This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.
I32 agnCBuMlOamFrequency	1.3.6.1.4.1.164.3.1.2.2.12.1.6	Integer32	read-write	Time in sec. between 2 OAM packets.
I32 agnCBuMlOamTimeoutCycles	1.3.6.1.4.1.164.3.1.2.2.12.1.7	Integer32	read-write	No. of cycles the Link will send OAM packets without receiving a response from the remote Link before switching to the Backup Link.
I32 agnCClkCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..100) being accessed and Idx 255 relates to the TmpCnfg.
I32 agnCClkSrcIdx	1.3.6.1.4.1.164.3.1.2.2.4.1.2	Integer32	read-only	An index to the table. There are only two entries to this table. Index 1 points to the Master clock parameters and Index 2 points to the Fallback clock parameters
I32 agnCClkSrcPrt	1.3.6.1.4.1.164.3.1.2.2.4.1.5	Integer32	read-write	This entry is valid only when we are working in rxClk or adaptive mode. For an invalid entry, the return value will be '7fff'h. - For rxClk mode, the values can be: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , notApplicable (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) - For adaptive mode, the value will be the ifIndex of the selected IP Bundle.
I32 agnCDefaultCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.6	Integer32	read-write	Setting this attribute will define the desired working configuration when no conditions of the Flip DB Table are fulfilled and no Net GO command was issued. This command will be accepted only if the Configuration number exists (agnSEntryIsValid=yes).
I32 agnCDeleteCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.5	Integer32	read-write	Setting this attribute will delete the requested DB from the NVRAM .
I32 agnCFlipDbNo	1.3.6.1.4.1.164.3.1.2.5.3.1.5	Integer32	read-write	The ID of the required DB
I32 agnCFlipIdx	1.3.6.1.4.1.164.3.1.2.5.3.1.2	Integer32	read-only	Entry number within the table
I32 agnCFlipNetEventIdx	1.3.6.1.4.1.164.3.1.2.5.2.1.2	Integer32	read-only	Entry within the table
I32 agnCFlipNetEventISD	1.3.6.1.4.1.164.3.1.2.5.2.1.8	Integer32	read-write	The time in seconds since the Net Event was reported as ON until it is considered as ON. Not relevant for time events.
I32 agnCFlipNetEventNo	1.3.6.1.4.1.164.3.1.2.5.2.1.5	Integer32	read-write	The Net Event No. (Bit Index)
I32 agnCFlipNetEventOSD	1.3.6.1.4.1.164.3.1.2.5.2.1.9	Integer32	read-write	The time in seconds since the net event was reported as OFF until it is considered as OFF. Not relevant for time events.
I32 agnCFlipNetEventPort	1.3.6.1.4.1.164.3.1.2.5.2.1.7	Integer32	read-write	The port within the relevant slot. Valid values: - extPrt1(1)..exPrt16(16) - notApplicable(100) - inPrt1(101)..inPrt84(184)
I32 agnClkSrcPort	1.3.6.1.4.1.164.6.2.52.1.1.4	Integer32	read-create	This object indicates the Port/Interface Index of the port that is to be used as Clock Source. In case of Recovered Clock - it indicates the PW number.
I32 agnClkSrcPortCnfgIdx	1.3.6.1.4.1.164.6.2.52.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. For product supporting a single configuration, the value will be 1.
I32 agnClkSrcPortIdx	1.3.6.1.4.1.164.6.2.52.1.1.3	Integer32	not-accessible	This object indicates the running Idx of the port that is to be used as Clock Source, for each agnClkSrcPortSrcIdx instance. In case of Recovered Clock - it indicates the Clock ID.
I32 agnCLoadCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.3	Integer32	read-write	This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on Valid configurations (agnSEntryIsValid)
I32 agnCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 agnCmprTypIdx	1.3.6.1.4.1.164.3.1.2.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 agnCmprVersion	1.3.6.1.4.1.164.3.1.2.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnCNetDelay	1.3.6.1.4.1.164.3.1.2.5.4.6	Integer32	read-write	This attribute determines the period of time in seconds that takes for a message to be transferred over all the network. After a 'GO' command the MUX issues a delay of 'agnCNetDelay' before activating the appropriate DB. The delay will be applied only after performing agnCSaveFlipDbCmd.
I32 agnCNetEventsBcastInterval	1.3.6.1.4.1.164.3.1.2.5.4.8	Integer32	read-write	When agnCNetEventsBcast is enabled, this object determines the interval of time in seconds, between two consecutive Net Events transferred over the network. Default=40 sec. The interval will be applied only after performing agnCSaveFlipDbCmd.
I32 agnCnfgAlrCode	1.3.6.1.4.1.164.3.1.2.2.8.2.1.1	Integer32	read-only	The alarm code. The following attributes refer this code.
I32 agnCnfgAlrFilterReset	1.3.6.1.4.1.164.3.1.2.2.8.2.1.8	Integer32	read-write	This is a bottom threshold causing the alarm that does not pass it, to be declared Reset (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at most, during the window, in order to be considered OFF. This value should be less than the one of agnCnfgAlrFilterSet. Agents that do not support Alarms Filter, will return 0.
I32 agnCnfgAlrFilterSet	1.3.6.1.4.1.164.3.1.2.2.8.2.1.7	Integer32	read-write	This is a top threshold causing the alarm that passes it, to be declared Set (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at least, during the window in order to be considered ON. The maximum value will be 255. This value should be greater than the one of agnCnfgAlrFilterReset. Agents that do not support Alarms Filter, will return 0.
I32 agnCnfgAlrFilterWindow	1.3.6.1.4.1.164.3.1.2.2.8.1	Integer32	read-write	Window of time, in seconds. During this Window, the alarms filter is performed. Same Window for all agent alarms that need filtering. Upon end of the Window, the state of the alarm is updated and a new Window starts. If no alarm needs filtering, this object's value will not be used.
I32 agnCnfgAlrPort	1.3.6.1.4.1.164.3.1.2.2.8.2.1.3	Integer32	read-only	The alarm port. The following attributes apply for the alarm code,slot and port selected. 200 = all = the attributes apply to all ports of the selected slot. When selected Slot is 'all', only 'all' or 'notApplicable' are valid Port selections. notApplicable = the selected alarm is for system or card level. =255 for MP =100 for DXC - For MP: - valid cards' ports are: exPrt1(1)..exPrt16(16) inPrt1(101)..inPrt48 (148) - IP Bundles - For DXC, the port index will include the Slot, as for all DXC tables: [(IO Slot+10)&n] ; n=odd for external ports n=even for internal ports.
I32 agnCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.7.1.1	Integer32	read-only	This object indicates the Idx of the agent' Cnfg the following objects refer. 255=Temporary Cnfg (Set is done only to this configuration).
I32 agnCQ50BlockNewModemRelayCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.5	Integer32	read-write	This object indicates the Modem Relay Calls Threshold percent (%) above which new modem calls will be rejected.
I32 agnCQ50BlockNewModemVbdCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.4	Integer32	read-write	This object indicates the Modem VBD Calls Threshold percent (%) above which new modem calls will be rejected.
I32 agnCQ50CnfgIdx	1.3.6.1.4.1.164.3.1.2.2.13.1.1	Integer32	not-accessible	This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.
I32 agnCQ50DiscardPktThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.3	Integer32	read-write	This object indicates the Bandwidth Threshold percent (%) above which voice packets will be discarded. Usually, the value selected should be higher than the value of agnCQ50StopCallsThresh.
I32 agnCQ50StopCallsThresh	1.3.6.1.4.1.164.3.1.2.2.13.1.2	Integer32	read-write	This object indicates the Bandwidth Threshold percent (%) above which new Calls from the PBX will be disabled.
I32 agnCSaveCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.2.2	Integer32	read-write	This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown
I32 agnCSaveNetCnfgIdxCmd	1.3.6.1.4.1.164.3.1.2.5.4.3	Integer32	read-write	This attribute specifies the Id of the target NVRAM Cnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown. This attribute doesn't cause actual Flip.
I32 agnCT1E1RingCnfgIdx	1.3.6.1.4.1.164.3.1.2.2.10.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
I32 agnCT1E1RingPrimePort	1.3.6.1.4.1.164.3.1.2.2.10.1.3	Integer32	read-only	The port number in the Primary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104
I32 agnCT1E1RingRecTime	1.3.6.1.4.1.164.3.1.2.2.10.1.6	Integer32	read-create	T1/E1 Ring Recovery Time (sec). Valid Values: 1..99, 65535. 65535=NA.
I32 agnCT1E1RingSecPort	1.3.6.1.4.1.164.3.1.2.2.10.1.5	Integer32	read-create	The port number in the Secondary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104
I32 agnCurrClkObjIdx	1.3.6.1.4.1.164.6.2.52.2.1.1	Integer32	not-accessible	This MIB object identifies the object for which the Clock Source is used (System, Other System, Card).
I32 agnCurrClkPort	1.3.6.1.4.1.164.6.2.52.2.1.4	Integer32	read-only	This object indicates the Port/Interface Index of the port that is Currently used as Clock Source.
I32 agnDlciCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.2.1.1	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 agnDlciCmprDlciIdx	1.3.6.1.4.1.164.3.1.2.3.2.1.3	Integer32	read-only	This attribute indicates a unique identifier of the Dlci, the compressed information relates to. The values are between 16 - 991.
I32 agnDlciCmprVersion	1.3.6.1.4.1.164.3.1.2.3.2.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 agnDlciCnfgIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 agnDlciHIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.7	Integer32	read-only	This attribute indicates a unique internal connection DLCI number where the Source DLCI is routed to - the Destination Side of the DLCI.
I32 agnDlciHPrtIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.6	Integer32	read-only	This attribute indicates a unique port number where the DLCI is routed to - Destination Port.
I32 agnDlciLIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used DLCI(16..991). This is the Source Side of the DLCI. 0=notApplicable (for voice switching) LIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
I32 agnDlciLPrtIdx	1.3.6.1.4.1.164.3.1.2.8.1.1.3	Integer32	read-only	This attribute indicates a unique external or internal port number, including linkSelector or encapsulator. This is the Source Port of the DLCI. 100=noConnect (for voice switching) LPrtIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
I32 agnDlciPriority	1.3.6.1.4.1.164.3.1.2.8.1.1.12	Integer32	read-create	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 7 is the highest priority.
I32 agnListDecodingCode	1.3.6.1.4.1.164.3.1.2.7.1.1.2	Integer32	read-only	The specific code for which decoding is needed.
I32 agnManagerConfigPorts	1.3.6.1.4.1.164.6.2.46	Integer32	read-write	This variable defines from which port/s this manager can manage the device. The value is a sum of 2**n, where n is a bit assigned to a certain port. For RIC-E1 and ETX 102 the value will be according to the ports combination: Network = bit 0 User= bit 1 For Example: All = 3.
I32 agnMaxNoOfConns	1.3.6.1.4.1.164.6.2.53	Integer32	read-only	This variable indicates the maximum number of connections that can be configured for the agent.
I32 agnNoOfCurrentConns	1.3.6.1.4.1.164.6.2.48	Integer32	read-only	This variable indicates the number of connections currently configured for the agent.
I32 agnSActiveCnfg	1.3.6.1.4.1.164.3.1.2.1.4	Integer32	read-only	This entry specifies the unique identifier of the configuration, that is currently active and running.
I32 agnSAlrCode	1.3.6.1.4.1.164.3.1.2.1.15.1.3	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at system level.
I32 agnSAlrCounter	1.3.6.1.4.1.164.3.1.2.1.15.1.6	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
I32 agnSAlrIdx	1.3.6.1.4.1.164.3.1.2.1.15.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
I32 agnSaSwchStatus	1.3.6.1.4.1.164.3.1.2.6.1	Integer32	read-only	This object indicates the status of the switches on the stand-alone unit. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits: bit 0 NMS (LSB) bit 1 Terminal '1' = forces the DCE to be terminal with Rate=9600bps, Data bits=8, Stop bits=1 bit 2 Xray bit 3 SW-Load '1' = when SW is loaded bit 4 DBS Default of all bits=0 When the status of these switches is unknown, the value of this object is 255.
I32 agnSCmprErrIdx	1.3.6.1.4.1.164.3.1.2.3.5.1.2	Integer32	read-only	Unique number to identify an entry in the errors list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'.
I32 agnSCmprErrVersion	1.3.6.1.4.1.164.3.1.2.3.5.1.1	Integer32	read-only	The version of the compressed data
I32 agnSEditCnfg	1.3.6.1.4.1.164.3.1.2.1.5	Integer32	read-only	This entry indicates the unique identifier of the configuration that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process.
I32 agnSendTrapParameter	1.3.6.1.4.1.164.6.2.27	Integer32	read-write	This object specifies if the agent will attach a specific parameter to a trap. For ACE2002 the agent will attach or not the openViewSeverity parameter according to the value of this parameter: 1 - will attach openViewSeverity. 0 - will not attach openViewSeverity.
I32 agnSEntryIdx	1.3.6.1.4.1.164.3.1.2.1.22.1.1	Integer32	read-only	Unique number to identify an entry in the configuration table.
I32 agnSErrIdx	1.3.6.1.4.1.164.3.1.2.1.20.1.1	Integer32	read-only	Unique number to identify an entry in the error list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'.
I32 agnSigProfCnfgIdx	1.3.6.1.4.1.164.3.1.2.10.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
I32 agnSigProfIdx	1.3.6.1.4.1.164.3.1.2.10.2.1.2	Integer32	read-only	This attribute indicates the Signaling Profile (1..5).
I32 agnSigProfileCnfgIdx	1.3.6.1.4.1.164.3.1.2.10.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. For products supporting more than one configuration,the write operation is valid only to the TmpCnfg. For Gmux2000 the range limitation (1..255) was discarded since the Idx is computed as: x 1000 + 255.
I32 agnSigProfileIdx	1.3.6.1.4.1.164.3.1.2.10.1.1.2	Integer32	read-only	This attribute indicates the Signaling Profile (1..5). For MP-104/204, only Profile=1 will exist.
I32 agnSMaxNoOfCnfg	1.3.6.1.4.1.164.3.1.2.1.21	Integer32	read-only	Maximum number of configurations that can be defined and stored in the MUX. If the mux has a large capacity, the maximum will be limited to 254.
I32 agnSNoOfSanityCheckErr	1.3.6.1.4.1.164.3.1.2.1.19	Integer32	read-only	This entry indicates the number of errors/warnings discovered by the last SanityCheck process.
I32 agnStatNoOfUploadedIntervals	1.3.6.1.4.1.164.6.2.57	Integer32	read-only	This parameter indicates the Number of Intervals that were successfully collected and uploaded in the last statistics collection session.
I32 agnTrapMask	1.3.6.1.4.1.164.6.2.2	Integer32	read-write	The value of this attribute determines the type of traps the agent should mask and not send to the management console. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
I32 agnTsCmprCnfgIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.2	Integer32	read-only	This object indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration.
I32 agnTsCmprPduIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.5	Integer32	read-only	This object indicates the PDU index within the same port. That provides for the case when one PDU is not sufficient for all TS Assignment data of the same port.
I32 agnTsCmprPortIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.4	Integer32	read-only	This object indicates the Port within the Slot, to which the Compressed information is related. For Port Index see each product's spec.
I32 agnTsCmprSlotIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.3	Integer32	read-only	This object indicates the Slot to which the Compressed information is related. For MP-2100: IO-1..IO-12 = (5).. (16) For DXC-30 : IO-1..IO-15 = (5).. (19). NA=255.
I32 agnTsCmprVerIdx	1.3.6.1.4.1.164.3.1.2.3.6.1.1	Integer32	read-only	This object indicates the version of the internal format of the Compressed data.
I32 agnVoiceSwConfHGExt	1.3.6.1.4.1.164.3.1.2.9.5.1.4	Integer32	read-write	This is the extension number of the hunt group. 0 is for not valid. The allowed range is 10 - 99.
I32 agnVoiceSwConfHGIdx	1.3.6.1.4.1.164.3.1.2.9.5.1.2	Integer32	read-only	For Vmux-300 devices - This object represents a combination of - Hunt Group number and Extension number OR - Port number and Extension number. For other devices (e.g. MXcess, MP-2100H) - There may be up to 10 Hunt Groups per MXcess. That's the index of the hunt group relevant to this row.
I32 agnVoiceSwConfLidt	1.3.6.1.4.1.164.3.1.2.9.1.1.6	Integer32	read-write	LIDT: Long Inter Digit Timeout used as timer between digits before routing is completed. If no digits were dialed and LIDT expired then the user will get an error tone and the call will be disconnected. 0 = notApplicable Default=15 sec.
I32 agnVoiceSwConfNoOfHops	1.3.6.1.4.1.164.3.1.2.9.1.1.4	Integer32	read-write	Number of hops the frame will go through the net before deciding to discard the frame (like time-to-live in IP). 0 = notApplicable Default=20 .
I32 agnVoiceSwConfRtDlci	1.3.6.1.4.1.164.3.1.2.9.2.1.8	Integer32	read-create	Routing DLCI- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). Valid values: 0=notApplicable (for non-routing case). 1, 16..991
I32 agnVoiceSwConfRtIdx	1.3.6.1.4.1.164.3.1.2.9.2.1.2	Integer32	read-only	The Index of the row.
I32 agnVoiceSwConfRtMaxCalls	1.3.6.1.4.1.164.3.1.2.9.2.1.10	Integer32	read-create	Maximum no. of simultaneous voice calls that are allowed in the direction defined by the current entry. Default=0 (No Limit).
I32 agnVoiceSwConfRtPort	1.3.6.1.4.1.164.3.1.2.9.2.1.7	Integer32	read-create	Routing Port- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). 100=noConnect (for non-routing case).
I32 agnVoiceSwConfRtPriority	1.3.6.1.4.1.164.3.1.2.9.2.1.11	Integer32	read-create	This attribute indicates a unique priority of the Voice Switching Route. 1 is the lowest priority and 7 is the highest priority. 0 means N/A
I32 agnVoiceSwConfSidt	1.3.6.1.4.1.164.3.1.2.9.1.1.5	Integer32	read-write	SIDT: Short Inter Digit Timeout used as timer (in sec.) between digits after routing is completed. The timeout indicates end of dialing and the call can then be setup. 0 = notApplicable Default=2 sec.
I32 agnXCmprIdx3	1.3.6.1.4.1.164.3.1.2.3.7.1.3	Integer32	read-only	3rd index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant, this attribute indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration.
I32 agnXCmprIdx4	1.3.6.1.4.1.164.3.1.2.3.7.1.4	Integer32	read-only	4th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique number of the slot position where the card is inserted. Valid values: psA(1),psB(2),clA(3),clB(4),io1(5)..io12(16); notApplicable=255.
I32 agnXCmprIdx5	1.3.6.1.4.1.164.3.1.2.3.7.1.5	Integer32	read-only	5th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt12 (12) , inPrt1 (101) .. inPrt48 (148).
I32 agnXCmprIdx6	1.3.6.1.4.1.164.3.1.2.3.7.1.6	Integer32	read-only	6th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates the Variant index. Valid values are: 0..127, 255 (= temp cnfg).Set can be performed only to the temporary configuration.
I32 agnXCmprIdx7	1.3.6.1.4.1.164.3.1.2.3.7.1.7	Integer32	read-only	7th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute is not needed. Therefore, its value will be always 255=notApplicable.
I32 agnXCmprTypIdx	1.3.6.1.4.1.164.3.1.2.3.7.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred. One of the types is V5.1 Variant data.
I32 agnXCmprVersion	1.3.6.1.4.1.164.3.1.2.3.7.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data.
I32 alarmForwardingFailPort	1.3.6.1.4.1.164.6.2.50.1.1	Integer32	not-accessible	An Index of the port on which a fail occurs.
I32 alarmForwardingGroupConditions	1.3.6.1.4.1.164.6.2.50.1.5	Integer32	read-create	This parameter is applicable when there is a group of interfaces in which a fault may occur, and one interface to which alarm is propagated (forwarded). 0 = All - Forwarding will take place only when all interfaces of the same group are faulty. 1 = Single - Forwarding will take place when at least one (single) interface of the same group (any of them) is faulty. n - forwarding will take place only when n (n < all) interfaces of the same group fail.
I32 alarmForwardingRecoveryTime	1.3.6.1.4.1.164.6.2.50.1.4	Integer32	read-create	This parameter defines the maximum time (sec) the affected port will hold the down state.
I32 alarmForwardingToPort	1.3.6.1.4.1.164.6.2.50.1.2	Integer32	not-accessible	An Index of the port that will be affected upon the failure of the alarmForwardingFailPort.
I32 alrBufIdx	1.3.6.1.4.1.164.3.1.2.4.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify this entry
I32 alrGenCode	1.3.6.1.4.1.164.3.3.4.3.1.1	Integer32	read-only	This object is a unique code number, identifying a certain alarm.
I32 alrGenDebounce	1.3.6.1.4.1.164.3.3.4.3.1.6	Integer32	read-write	Debounce time for each alarm code, in seconds. The meaning is, that an alarm will be 'declared' as ON (or OFF), only after it was actually ON/OFF the Debouncing time selected by user. 0 = default debounce selection (each alarm has a default value). 250 = maximum value of seconds for debounce. 253 = mask = the alarm will Never be reported. 254 = default debounce selection (each alarm has a default value). 255 = not applicable
I32 atmAlarmForwardingFailPort	1.3.6.1.4.1.164.12.3.1.1.32.1.1	Integer32	not-accessible	An Index of the port on which a fail occurs.
I32 atmAlarmForwardingToPort	1.3.6.1.4.1.164.12.3.1.1.32.1.2	Integer32	not-accessible	An Index of the port that will be affected upon the failure of the atmAlarmForwardingFailPort.
I32 atmConfIfAllocatedBw	1.3.6.1.4.1.164.12.3.2.1.1.1.10	Integer32	read-only	Total VC Bandwidth Allocation.
I32 atmConfIfInputRate	1.3.6.1.4.1.164.12.3.2.1.1.1.8	Integer32	read-write	This parameter indicates the input rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.
I32 atmConfIfLowerVpi	1.3.6.1.4.1.164.12.3.2.1.1.1.11	Integer32	read-write	The Lower possible VPI.
I32 atmConfIfOutputRate	1.3.6.1.4.1.164.12.3.2.1.1.1.7	Integer32	read-write	This parameter indicates the output rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.
I32 atmConfVpLoopbackFailureThreshold	1.3.6.1.4.1.164.12.3.2.1.3.1.12	Integer32	read-write	The number of the LB failures before starting transmission of the Indication defined by atmConfVcLoopbackFailureInd. Range: 1..16. Default: 1.
I32 atmConfVpOamDescrIndex	1.3.6.1.4.1.164.12.3.2.1.3.1.14	Integer32	read-write	This parameter indicates the VPL's OAM Descriptor index, according to the OAM Descriptor Configuration Table.
I32 atmGenSysCxRefIndex	1.3.6.1.4.1.164.12.2.2.1.5.1.1	Integer32	read-only	The index specifies an entry in the table of the object.
I32 atmGenSysLogIndex	1.3.6.1.4.1.164.12.2.2.1.3.1.1	Integer32	read-only	The index of the log buffer.
I32 atmGenSysSelfTestIndex	1.3.6.1.4.1.164.12.2.2.1.1.1.1	Integer32	read-only	A running index for the table.
I32 atmIfIntervalNumber	1.3.6.1.4.1.164.12.2.1.1.3.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
I32 atmIfTimeElapsed	1.3.6.1.4.1.164.12.2.1.1.1.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
I32 atmIfValidIntervals	1.3.6.1.4.1.164.12.2.1.1.1.1.2	Integer32	read-only	The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
I32 atmInterfaceActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.2.1.1	Integer32	read-only	A Bit String of the active alarms on this interface. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - LOS 2 - LOF 3 - Line AIS (SONET)/ PLCP LOF (DS3) 4 - LOP 5 - Path AIS 6 - SLM 7 - LCD 8 - Line RDI (SONET)/ PLCP Yellow (DS3) 9 - Path RDI (SONET)/ RDI (DS3) 10 - Section BIP (SONET)/ P1/P2 (DS3) > Threshold 11 - Line BIP (SONET)/ PLCP BIP (DS3) > Threshold 12 - Line FEBE (SONET)/ PLCP FEBE (DS3) > Threshold 13 - Path BIP > Threshold 14 - Path FEBE > Threshold 15 - HW Failure
I32 atmInterfaceMaskAlarms	1.3.6.1.4.1.164.12.3.2.1.2.1.11	Integer32	read-write	A Bit String of alarms mask on this interface. An up bit (1) means that the respective alarm is masked. A down bit (0) means no mask. The mask is supported for the following alarms: 1 - LOS
I32 atmIntervalDateInterval	1.3.6.1.4.1.164.12.2.1.3.1.1	Integer32	read-only	The interval number defining this entry.
I32 atmLoopbackVcAverageDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.6	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVcCDV	1.3.6.1.4.1.164.12.3.2.2.2.1.5	Integer32	read-only	Cell Delay Variation for this sampling.
I32 atmLoopbackVcErrSessions	1.3.6.1.4.1.164.12.3.2.2.2.1.9	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
I32 atmLoopbackVcIfIndex	1.3.6.1.4.1.164.12.3.2.2.2.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVcIvlAverageDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.7	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVcIvlCDV	1.3.6.1.4.1.164.12.3.2.2.4.1.6	Integer32	read-only	Cell Delay Variation for this interval.
I32 atmLoopbackVcIvlErrSessions	1.3.6.1.4.1.164.12.3.2.2.4.1.10	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
I32 atmLoopbackVcIvlIfIndex	1.3.6.1.4.1.164.12.3.2.2.4.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVcIvlIvl	1.3.6.1.4.1.164.12.3.2.2.4.1.4	Integer32	read-only	The relevant interval number.
I32 atmLoopbackVcIvlMaxDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.8	Integer32	read-only	The maximum delay without including lost cells.
I32 atmLoopbackVcIvlMinDelay	1.3.6.1.4.1.164.12.3.2.2.4.1.9	Integer32	read-only	The minimum delay.
I32 atmLoopbackVcIvlVci	1.3.6.1.4.1.164.12.3.2.2.4.1.3	Integer32	read-only	The VCI of the OAM VCL.
I32 atmLoopbackVcIvlVpi	1.3.6.1.4.1.164.12.3.2.2.4.1.2	Integer32	read-only	The VPI of the OAM VCL.
I32 atmLoopbackVcMaxDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.7	Integer32	read-only	The maximum delay without including lost cells.
I32 atmLoopbackVcMinDelay	1.3.6.1.4.1.164.12.3.2.2.2.1.8	Integer32	read-only	The minimum delay.
I32 atmLoopbackVcVci	1.3.6.1.4.1.164.12.3.2.2.2.1.3	Integer32	read-only	The VCI of the OAM VCL.
I32 atmLoopbackVcVpi	1.3.6.1.4.1.164.12.3.2.2.2.1.2	Integer32	read-only	The VPI of the OAM VCL.
I32 atmLoopbackVpAverageDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.5	Integer32	read-only	Average delay without including lost cells.
I32 atmLoopbackVpCDV	1.3.6.1.4.1.164.12.3.2.2.1.1.4	Integer32	read-only	Cell Delay Variation for this sampling.
I32 atmLoopbackVpErrSessions	1.3.6.1.4.1.164.12.3.2.2.1.1.8	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
I32 atmLoopbackVpIfIndex	1.3.6.1.4.1.164.12.3.2.2.1.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVpIvlAverageDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.6	Integer32	read-only	Average delay without including lost cells for this interval.
I32 atmLoopbackVpIvlCDV	1.3.6.1.4.1.164.12.3.2.2.3.1.5	Integer32	read-only	Cell Delay Variation for this interval.
I32 atmLoopbackVpIvlErrSessions	1.3.6.1.4.1.164.12.3.2.2.3.1.9	Integer32	read-only	Errored Sessions. Will be updated once in 5 seconds.
I32 atmLoopbackVpIvlIfIndex	1.3.6.1.4.1.164.12.3.2.2.3.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmLoopbackVpIvlIvl	1.3.6.1.4.1.164.12.3.2.2.3.1.3	Integer32	read-only	The relevant interval number.
I32 atmLoopbackVpIvlMaxDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.7	Integer32	read-only	The maximum delay without including lost cells for this interval.
I32 atmLoopbackVpIvlMinDelay	1.3.6.1.4.1.164.12.3.2.2.3.1.8	Integer32	read-only	The minimum delay for this interval.
I32 atmLoopbackVpIvlVpi	1.3.6.1.4.1.164.12.3.2.2.3.1.2	Integer32	read-only	The VPI of the OAM VPL.
I32 atmLoopbackVpMaxDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.6	Integer32	read-only	Maximum delay without including lost cells.
I32 atmLoopbackVpMinDelay	1.3.6.1.4.1.164.12.3.2.2.1.1.7	Integer32	read-only	Minimum delay.
I32 atmLoopbackVpVpi	1.3.6.1.4.1.164.12.3.2.2.1.1.2	Integer32	read-only	The VPI of the OAM VPL.
I32 atmNteConnectionsNumber	1.3.6.1.4.1.164.12.3.1.2.13	Integer32	read-only	This object specifies a quantity of connections.
I32 atmNteDefaultLoopbackThreshold	1.3.6.1.4.1.164.12.3.1.1.27	Integer32	read-write	The Default OAM Loopback Failure Threshold value that will be used for configuration.
I32 atmNteDefaultVci	1.3.6.1.4.1.164.12.3.1.1.21	Integer32	read-write	Default Vci for management.
I32 atmNteDefaultVpi	1.3.6.1.4.1.164.12.3.1.1.20	Integer32	read-write	Default Vpi for management.
I32 atmNteDPLTCR	1.3.6.1.4.1.164.12.3.1.1.3	Integer32	read-write	The Degraded ES Limit threshold for Performance Management.
I32 atmNteDSESLTCR	1.3.6.1.4.1.164.12.3.1.1.6	Integer32	read-write	The Degraded ES Limit threshold for Performance Management.
I32 atmNteGranularityFactor	1.3.6.1.4.1.164.12.3.1.1.29	Integer32	read-write	This parameter affects the granularity of the guaranteed Rate (SCR+MCR) in spaced connection (cell/sec units). It is also defines the minimum guaranteed rate in spaced connection.
I32 atmNteHostAtmIfIndex	1.3.6.1.4.1.164.12.3.1.1.11.1.4	Integer32	read-create	ATM interface index. Will be 1 for user port, and 2 for network port.
I32 atmNteHostDefaultVlanID	1.3.6.1.4.1.164.12.3.1.1.11.1.12	Integer32	read-create	Default VLAN ID of this Host.
I32 atmNteHostDefaultVlanPriority	1.3.6.1.4.1.164.12.3.1.1.11.1.13	Integer32	read-create	Default VLAN priority for this Host.
I32 atmNteHostPvcIndex	1.3.6.1.4.1.164.12.3.1.1.11.1.1	Integer32	read-only	A PVC index. The range is 1..10.
I32 atmNteHostRdnVci	1.3.6.1.4.1.164.12.3.1.1.11.1.9	Integer32	read-create	The VCI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).
I32 atmNteHostRdnVpi	1.3.6.1.4.1.164.12.3.1.1.11.1.8	Integer32	read-create	The VPI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).
I32 atmNteHostVci	1.3.6.1.4.1.164.12.3.1.1.11.1.6	Integer32	read-create	VCI of the PVC connected to that host interface.
I32 atmNteHostVpi	1.3.6.1.4.1.164.12.3.1.1.11.1.5	Integer32	read-create	VPI of the PVC connected to that host interface.
I32 atmNteIdIndex	1.3.6.1.4.1.164.12.3.1.2.1.1.1	Integer32	read-only	An Index of the Unit ID table. The following units have IDs in this table: 1 - System 2 - ATM Board 3 - User Card 4 - Trunk 1 card 5 - Trunk 2 card 6 - Shaper 7 - Clock Unit 8 - Slot 1 card 9 - Slot 2 card 10 - Slot 3 card 11 - Slot 4 card 12 - Fan1 13 - Fan2 14 - Control Unit.
I32 atmNteIntervalMaxNumber	1.3.6.1.4.1.164.12.3.1.2.10	Integer32	read-only	The MAX number of connections intervals supported by system. This parameter value is a function of atmNteConnectionsMaxNumber parameter. This parameter should affect the threshold values selected by user. Applicable to ace2002.
I32 atmNteLoopbackTimeout	1.3.6.1.4.1.164.12.3.1.1.25	Integer32	read-write	The Loopback state timeout in minutes. A value of zero means no timeout (for ever). Default is 5 min.
I32 atmNteManagerConfigPorts	1.3.6.1.4.1.164.12.3.1.1.1.1.13	Integer32	read-create	This variable defines from which port/s this manager can configure the device. For IPmux 11 the value of this variable will be according to the ports combination: Network =1 User1=2 User2=4 (For Example: All ports = 7).
I32 atmNteManagerIfIndex	1.3.6.1.4.1.164.12.3.1.1.1.1.3	Integer32	read-create	The ATM interface index of the management port.
I32 atmNteManagerPvc	1.3.6.1.4.1.164.12.3.1.1.1.1.2	Integer32	read-only	A PVC index. The range is 1..8. There are four PVCs on the User Port and four PVCs on the Network Port. The default VPI, VCI values are specified below.
I32 atmNteManagerTrapMask	1.3.6.1.4.1.164.12.3.1.1.1.1.6	Integer32	read-create	The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
I32 atmNteManagerVci	1.3.6.1.4.1.164.12.3.1.1.1.1.5	Integer32	read-create	The VCI of the management VCL. Defaults: 32,33,34,35.
I32 atmNteManagerVlanFramePriority	1.3.6.1.4.1.164.12.3.1.1.1.1.11	Integer32	read-create	VLAN Frame priority.Range is 0..7.
I32 atmNteManagerVlanIdentifier	1.3.6.1.4.1.164.12.3.1.1.1.1.10	Integer32	read-create	VLAN ID. Range is 0..4095.
I32 atmNteManagerVpi	1.3.6.1.4.1.164.12.3.1.1.1.1.4	Integer32	read-create	The VPI of the management VCL. Default: 0.
I32 atmNteMaxBurstSize	1.3.6.1.4.1.164.12.3.1.1.28	Integer32	read-write	The Maximum allowed burst size (cell units). This object is applicable for each Physical port.
I32 atmNteMdlSlotIndex	1.3.6.1.4.1.164.12.3.3.1.1.1.1	Integer32	not-accessible	The slot number.
I32 atmNteOutputRate	1.3.6.1.4.1.164.12.3.1.1.13	Integer32	read-write	Aggregate shaping output rate in Cells per Seconds units. Default value is the Network port rate.
I32 atmNteReservedVpi	1.3.6.1.4.1.164.12.3.1.1.22	Integer32	read-write	Internal use VPI, where shaperMode=vpInbandMng.
I32 atmNteTotalCc	1.3.6.1.4.1.164.12.3.1.2.15	Integer32	read-only	This parameter counts the total number of end-points that were configured with Continuity Check (CC).
I32 atmNteTotalInputRate	1.3.6.1.4.1.164.12.3.1.1.30	Integer32	read-only	This parameter indicates the total input rate of the device in cells/sec.
I32 atmNteTotalLb	1.3.6.1.4.1.164.12.3.1.2.14	Integer32	read-only	This parameter counts the total number of end-points that were configured with Loopback (LB).
I32 atmNteTotalOutputRate	1.3.6.1.4.1.164.12.3.1.1.31	Integer32	read-only	This parameter indicates the total output rate of the device in cells/sec.
I32 atmNteTotalPm	1.3.6.1.4.1.164.12.3.1.2.16	Integer32	read-only	This parameter counts the total number of end-points that were configured with PM.
I32 atmNteUnitId	1.3.6.1.4.1.164.12.3.1.2.1.1.2	Integer32	read-only	The ID of the Unit. For index = 6, the id will describe the validity of a shaper in the system: 0 - Shaper Not exist 1 - Shaper exist. For index = 7, the id will describe the validity of a clock in the system: 0 - Clock Not exist 1 - Clock exist. 2- Clock exist but failed. For index = 12,13 the id will describe the functionality of a FAN1 : 0 - OK 1 - Failed.
I32 atmNteUPLTCR	1.3.6.1.4.1.164.12.3.1.1.2	Integer32	read-write	The Unacceptable ES Limit threshold for Performance Management.
I32 atmNteUSESLTCR	1.3.6.1.4.1.164.12.3.1.1.5	Integer32	read-write	The Unacceptable SES Limit threshold for Performance Management.
I32 atmNteVcActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.6.1.3	Integer32	read-only	A Bit String of the active alarms on this VC. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VC AIS 2 - VC Loss Of Continuity 3 - VC RDI 4 - VC Errored Cells > Threshold 5 - VC Lost Cells > Threshold 6 - VC Misinserted Cells > Threshold 7 - Tx VC AIS 8 - Tx VC RDI 9 - VC Loopback Failure
I32 atmNteVcAlarmVci	1.3.6.1.4.1.164.12.3.2.1.6.1.2	Integer32	read-only	The VCI of the VC on which there is an active alarm.
I32 atmNteVcAlarmVpi	1.3.6.1.4.1.164.12.3.2.1.6.1.1	Integer32	read-only	The VPI of the VC on which there is an active alarm.
I32 atmNteVpActiveAlarms	1.3.6.1.4.1.164.12.3.2.1.5.1.2	Integer32	read-only	A Bit String of the active alarms on this VP. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VP AIS 2 - VP Loss Of Continuity 3 - VP RDI Reception 4 - VP Errored Cells > Threshold 5 - VP Lost Cells > Threshold 6 - VP Misinserted Cells > Threshold 9 - VP Loopback Failure
I32 atmNteVpAlarmVpi	1.3.6.1.4.1.164.12.3.2.1.5.1.1	Integer32	read-only	The VPI on which there is an active alarm.
I32 atmSysConfigCellTestQuantity	1.3.6.1.4.1.164.12.3.1.1.33.8	Integer32	read-write	Quantity of cells to send.
I32 atmSysConfigCellTestVci	1.3.6.1.4.1.164.12.3.1.1.33.3	Integer32	read-write	The VCI on which the cell test will be sent.
I32 atmSysConfigCellTestVpi	1.3.6.1.4.1.164.12.3.1.1.33.2	Integer32	read-write	The VPI on which the cell test will be sent.
I32 atmSysFanUnits	1.3.6.1.4.1.164.12.3.1.2.4	Integer32	read-only	The number of fan units.
I32 atmSysIntervalNumber	1.3.6.1.4.1.164.12.3.1.2.8.2.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
I32 atmSysNetPrts	1.3.6.1.4.1.164.12.3.1.2.5	Integer32	read-only	The number of network ports.
I32 atmSysPSunits	1.3.6.1.4.1.164.12.3.1.2.2	Integer32	read-only	The number of power supply units.
I32 atmThresholdErroredCells	1.3.6.1.4.1.164.12.3.2.1.2.1.7	Integer32	read-write	When Errored Cells are greater than this threshold, an active alarm is raised.
I32 atmThresholdLineBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.3	Integer32	read-write	When Line BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
I32 atmThresholdLineFEBE	1.3.6.1.4.1.164.12.3.2.1.2.1.4	Integer32	read-write	When Line FEBEs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
I32 atmThresholdLostCells	1.3.6.1.4.1.164.12.3.2.1.2.1.8	Integer32	read-write	When Lost Cells are greater than this threshold, an active alarm is raised.
I32 atmThresholdMisinsertedCells	1.3.6.1.4.1.164.12.3.2.1.2.1.9	Integer32	read-write	When Misinserted Cells are greater than this threshold, an active alarm is raised.
I32 atmThresholdPathBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.5	Integer32	read-write	When Path BIPs are greater than this threshold, an active alarm is raised.
I32 atmThresholdPathFEBE	1.3.6.1.4.1.164.12.3.2.1.2.1.6	Integer32	read-write	When Path FEBEs are greater than this threshold, an active alarm is raised.
I32 atmThresholdSectionBIP	1.3.6.1.4.1.164.12.3.2.1.2.1.2	Integer32	read-write	When Section BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
I32 atmVcCurrentVci	1.3.6.1.4.1.164.12.2.1.2.2.1.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.2.1.1.1	Integer32	read-only	The VPI of the VCL.
I32 atmVcIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.2.3.1.3	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
I32 atmVcIntervalVci	1.3.6.1.4.1.164.12.2.1.2.2.3.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.2.3.1.1	Integer32	read-only	The VPI of the VCL.
I32 atmVcPmBlockSize	1.3.6.1.4.1.164.12.3.2.3.2.1.6	Integer32	read-create	Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.
I32 atmVcPMCurrentDir	1.3.6.1.4.1.164.12.2.1.2.2.2.1.3	Integer32	read-only	The direction of Performance Management.
I32 atmVcPMCurrentVci	1.3.6.1.4.1.164.12.2.1.2.2.2.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcPMCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.2.2.1.1	Integer32	read-only	The VPI of the VCL.
I32 atmVcPmIfIndex	1.3.6.1.4.1.164.12.3.2.3.2.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmVcPMIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.2.4.1.4	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
I32 atmVcPMIntervalVci	1.3.6.1.4.1.164.12.2.1.2.2.4.1.2	Integer32	read-only	The VCI of the VCL.
I32 atmVcPMIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.2.4.1.1	Integer32	read-only	The VPI of the VCL.
I32 atmVcPmVci	1.3.6.1.4.1.164.12.3.2.3.2.1.3	Integer32	read-only	The VCI of the PM VCL.
I32 atmVcPmVpi	1.3.6.1.4.1.164.12.3.2.3.2.1.2	Integer32	read-only	The VPI of the Performance Monitoring VCL.
I32 atmVcQoSElapsedTime	1.3.6.1.4.1.164.12.2.1.2.2.6.1.2	Integer32	read-only	Elapsed Time in seconds. - for atmVcQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVcQoSPeriodRef = lastPeriod: The value of atmVcQoSElapsedTime when last systemResetAllStatsCmd was received.
I32 atmVcShaperMaxOccupation	1.3.6.1.4.1.164.12.2.1.2.2.8.1.3	Integer32	read-only	The Maximum number of Cells that were stored in the buffer, since this VC was activated. This parameter is limited to 20 bits.
I32 atmVcShaperOccupation	1.3.6.1.4.1.164.12.2.1.2.2.8.1.2	Integer32	read-only	The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.
I32 atmVpCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.1.1.1.1	Integer32	read-only	The VPI of the VPL.
I32 atmVpIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.1.3.1.2	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
I32 atmVpIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.1.3.1.1	Integer32	read-only	The VPI of the VPL.
I32 atmVpPmBlockSize	1.3.6.1.4.1.164.12.3.2.3.1.1.5	Integer32	read-create	Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.
I32 atmVpPMCurrentVpi	1.3.6.1.4.1.164.12.2.1.2.1.2.1.1	Integer32	read-only	The VPI of the VPL.
I32 atmVpPmIfIndex	1.3.6.1.4.1.164.12.3.2.3.1.1.1	Integer32	read-only	The interface index of the ATM layer.
I32 atmVpPMIntervalNumber	1.3.6.1.4.1.164.12.2.1.2.1.4.1.3	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
I32 atmVpPMIntervalVpi	1.3.6.1.4.1.164.12.2.1.2.1.4.1.1	Integer32	read-only	The VPI of the VPL.
I32 atmVpPmVpi	1.3.6.1.4.1.164.12.3.2.3.1.1.2	Integer32	read-only	The VPI of the Performance Monitoring VPL.
I32 atmVpQoSElapsedTime	1.3.6.1.4.1.164.12.2.1.2.1.5.1.2	Integer32	read-only	Elapsed Time in seconds. - for atmVpQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVpQoSPeriodRef = lastPeriod: The value of atmVpQoSElapsedTime when last systemResetAllStatsCmd was received.
I32 atmVpShaperMaxOccupation	1.3.6.1.4.1.164.12.2.1.2.1.7.1.3	Integer32	read-only	The Maximum number of Cells that were stored in the buffer, since this VP was activated. This parameter is limited to 20 bits.
I32 atmVpShaperOccupation	1.3.6.1.4.1.164.12.2.1.2.1.7.1.2	Integer32	read-only	The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.
I32 autoFileTransferOccurrenceRecurrence	1.3.6.1.4.1.164.6.2.12.13.1.1.6	Integer32	read-write	This object defines Occurrence reccurence interval, e.g N can be in 'every N alarms', 'every N log entries' etc. zero is used to indicate There's no Event Reccurence. (0= notApplicable) This object is taken into account only if autoFileTransferScheduling = recurrence Occurence Type (Alarms, etc.) is according to autoFileTransferType.
I32 autoFileTransferTimeRecurrence	1.3.6.1.4.1.164.6.2.12.13.1.1.5	Integer32	read-write	This object defines time reccurence interval, e.g. M can be 'every M days', 'every M hours' etc. Zero is used to indicate there's no time reccurence (0= notApplicable). This object is taken into account only if autoFileTransferScheduling = recurrence For LA-110 time units are days.
I32 bitMappingIndex	1.3.6.1.4.1.164.6.2.38.1.2	Integer32	read-only	The interface index or any other index that should be mapped.
I32 bitMappingLocation	1.3.6.1.4.1.164.6.2.38.1.1	Integer32	not-accessible	The bit location in an octet string.
I32 chassTotalNoOfClSlt	1.3.6.1.4.1.164.3.3.1.2.1.4	Integer32	read-only	This object indicates the number of physical Common Logic slots in the chassis.
I32 chassTotalNoOfIoSlt	1.3.6.1.4.1.164.3.3.1.2.1.2	Integer32	read-only	This object indicates the total number of physical IO slots in the chassis, (not all slots must be occupied and active).
I32 chassTotalNoOfMlSlt	1.3.6.1.4.1.164.3.3.1.2.1.5	Integer32	read-only	This object indicates the number of physical Main Link slots in the chassis (Kmux).
I32 chassTotalNoOfPsSlt	1.3.6.1.4.1.164.3.3.1.2.1.3	Integer32	read-only	This object indicates the number of physical Power Supply slots in the chassis.
I32 chassTotalNoOfSlt	1.3.6.1.4.1.164.3.3.1.2.1.1	Integer32	read-only	This object indicates the number of physical slots in the Hub chassis.
I32 chasTotalNoOfClSlt	1.3.6.1.4.1.164.3.1.1.5	Integer32	read-only	This entry indicates the number of physical Common Logic slots in the chassis.
I32 chasTotalNoOfIoSlt	1.3.6.1.4.1.164.3.1.1.3	Integer32	read-only	This entry indicates the total number of physical IO slots in the chassis, (not all slots hardware should be occupied and active) .
I32 chasTotalNoOfPsSlt	1.3.6.1.4.1.164.3.1.1.4	Integer32	read-only	This entry indicates the number of physical Power Supply slots in the chassis.
I32 chasTotalNoOfSlt	1.3.6.1.4.1.164.3.1.1.2	Integer32	read-only	This entry indicates the number of physical slots in the chassis.
I32 clearDwldStatusLog	1.3.6.1.4.1.164.6.2.12.12	Integer32	read-write	This object clears the status log. Value: off(2), external(3), internal(4) The Agent will change the value of this MIB object to off(2) automatically, after accepting the command .
I32 cmprCnfgIdx	1.3.6.1.4.1.164.3.3.4.1.1.2	Integer32	read-only	This object indicates the configuration number the Compressed information relates to.
I32 cmprPrtIdx	1.3.6.1.4.1.164.3.3.4.1.1.5	Integer32	read-only	This object indicates a unique identifier of the port, the compressed information relates to. For DXC - according to the order in the card of cmprSltIdx: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For FCD: see product's specification. If the port number is irrelevant to this parameter (if it is a system/card level alarm) the value will be 9999.
I32 cmprTypeIdx	1.3.6.1.4.1.164.3.3.4.1.1.1	Integer32	read-only	This object indicates the Type of the Compressed data referred (which table, which level, etc). The type is a code according to a convention between agent and NMS.
I32 cmprVersion	1.3.6.1.4.1.164.3.3.4.1.1.3	Integer32	read-only	This object indicates the version of the internal format of the Compressed data (the version of the convention used).
I32 dhcpClientLeaseExpirationTime	1.3.6.1.4.1.164.11.7.2.2.1.6.1.3	Integer32	read-only	This parameter holds the time (in minutes) left until lease expiration.
I32 dhcpPoolAllocTimeLeft	1.3.6.1.4.1.164.11.7.2.2.1.3.1.4	Integer32	read-only	IP address leasing time left in seconds
I32 dhcpRelayMaxHop	1.3.6.1.4.1.164.11.7.2.2.1.4.1.3	Integer32	read-write	Maximum number of hops till DHCP Server. upper limit is 16 hops
I32 dscpMappingCnfgIdx	1.3.6.1.4.1.164.6.3.2.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer to. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.
I32 dscpMappingRegenPriority	1.3.6.1.4.1.164.6.3.2.1.1.3	Integer32	read-write	The Regenerated Priority level the incoming DSCP value is mapped to. For FCD-155, valid values are 0,1,2,3
I32 dsx1BundleNextIndex	1.3.6.1.4.1.164.3.1.6.4.2.1.21	Integer32	read-only	This parameter indicates the Next free Bundle Index for this DS1 port.
I32 dsx1ClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.19	Integer32	read-write	This entry specifies the source from which the clock will be taken. Refer to device specification for source Index
I32 dsx1DataStreamStatIfIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.1	Integer32	not-accessible	The index of the DS1 interface. It may be ifIndex.
I32 dsx1DataStreamStatIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.2	Integer32	not-accessible	The DS1 Data Stream Index. For Vmux - the following indices are used: 1 for Transparent 2-3 for SS71-SS72 (respectively) 4-7 for Data1-Data4 (respectively) 8 for HDLC Ph2 Compatible 9-16 for Sub-CH1-1...Sub-CH1-8 (respectively).
I32 dsx1IdleCode	1.3.6.1.4.1.164.3.1.6.4.2.1.1	Integer32	read-write	Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).
I32 dsx1TcFirstSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.6	Integer32	read-write	Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used also for Space Signaling Code (in this case 0xFF is not NULL).
I32 dsx1TcPattern	1.3.6.1.4.1.164.3.1.6.4.2.1.8	Integer32	read-write	Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.
I32 dsx1TcSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.7	Integer32	read-write	Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).
I32 ethIfCurrentIndex	1.3.6.1.4.1.164.3.1.6.1.2.1.1.1	Integer32	read-only	The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval type can indicate: 1 minute, 15 minutes, 1 hour, 24 hours. For the exact formula, see device specification.
I32 ethIfIdx	1.3.6.1.4.1.164.3.1.6.1.1.1.1	Integer32	read-only	A unique index of the ethernet interface/port.
I32 ethIfIntervalIndex	1.3.6.1.4.1.164.3.1.6.1.2.2.1.1	Integer32	read-only	The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval type can indicate: 1 minute, 15 minutes, 1 hour, 24 hours. For the exact formula, see device specification.
I32 ethIfIntervalNumber	1.3.6.1.4.1.164.3.1.6.1.2.2.1.2	Integer32	read-only	The Interval Number. This number is between 1 and x, where 1 is the most recently completed interval and x is the least recently completed interval. For 15 minute intervals, usually x=96, but it can be different, depending on device capabilities.
I32 ethIfUse	1.3.6.1.4.1.164.3.1.6.1.1.1.19	Integer32	read-write	This parameter defines the use of the port. 1=NET 2=USER .
I32 ethOamServiceDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.6	Integer32	read-create	This object determines the delay threshold defined for this service, in measurement unit of 0.1 msec.
I32 ethOamServiceDelayVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.7	Integer32	read-create	This object determines the delay variation threshold defined for this service, in measurement unit of 0.1 msec.
I32 ethOamServiceFrameLossRatioThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.5	Integer32	read-create	This object determines the Frame Loss ratio threshold in exponent of 1/10. That is, a value of 4 means that the threshold is 1E-4.
I32 ethOamServiceUnavailRatioThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.8	Integer32	read-create	This object determines the Unavailability ratio threshold in exponent of 1/10. That is, a value of 4 means that the threshold is 1E-4.
I32 ethOamSvcCurrElapsedTime	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.12	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current interval.
I32 ethOamSvcIntervalNum	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.1	Integer32	not-accessible	The Interval index, which is actualy the Interval number, where 1 is the most recently completed 15 minute interval, and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
I32 ethRateLimit	1.3.6.1.4.1.164.3.1.6.1.1.1.15	Integer32	read-write	This parameter defines the Rate Limit of the line, in Mbps.
I32 hostIndex	1.3.6.1.4.1.164.6.2.40.1.1	Integer32	not-accessible	The Host Table Index. This index can have the same value as Host No.
I32 hostMode	1.3.6.1.4.1.164.6.2.40.1.5	Integer32	read-create	This parameter represents the Host mode of operation. There can be different values for each application. For example: Not Applicable = 1.
I32 hostParam1	1.3.6.1.4.1.164.6.2.40.1.6	Integer32	read-create	This parameter represents the first Host parameter. There can be different values for each application. For example: Not Applicable = 1.
I32 hostParam2	1.3.6.1.4.1.164.6.2.40.1.7	Integer32	read-create	This parameter represents the 2nd Host parameter. There can be different values for each application.
I32 hostParam3	1.3.6.1.4.1.164.6.2.40.1.8	Integer32	read-create	This parameter represents the 3nd Host parameter. There can be different values for each application.
I32 hostVlanId	1.3.6.1.4.1.164.6.2.40.1.11	Integer32	read-create	Host VLAN ID.
I32 hostVlanPriority	1.3.6.1.4.1.164.6.2.40.1.12	Integer32	read-create	Host VLAN Frame priority.
I32 ifCreateConnectedTo	1.3.6.1.4.1.164.6.2.35.1.1.7	Integer32	read-create	This object indicates the entity connected to the created Interface. The value of this object can be ifIndex of the connected entity or any other number that can identify it.
I32 ifCreateEntityIdx	1.3.6.1.4.1.164.6.2.35.1.1.2	Integer32	read-only	This object indicates the Index of the Entity that exists above the created interface. For a Logical Port, this value can be: 9999 - N/A when there is no fixed entity above it.
I32 ifCreateIndex	1.3.6.1.4.1.164.6.2.35.1.1.6	Integer32	read-only	This object indicates the ifIndex of the created Interface. The ifIndex is assigned by the device.
I32 ifCreateNumber	1.3.6.1.4.1.164.6.2.35.1.1.3	Integer32	read-only	This object indicates the number of the Interface that is created.
I32 ifPerfCounterType	1.3.6.1.4.1.164.6.2.35.2.1.1.1	Integer32	not-accessible	2nd index of the ifPerfTable. This parameter represents the Counter Type. Each application can have a different association between this object's value and counter type - see relevant application spec. For VPLS-MTU application use the following values: 1= Rx Octets, 2= Tx Octets, 3= Rx Frames, 4= Tx Frames, 5=Rx Dropped Frames, 6= Tx Dropped Frames. Optionally, counter type description appears in agnListDecodingTable
I32 ifTeQosIdx1	1.3.6.1.4.1.164.6.3.3.1.1.1	Integer32	not-accessible	This object indicates the 1st Index of the table.
I32 ifTeQosIdx2	1.3.6.1.4.1.164.6.3.3.1.1.2	Integer32	not-accessible	This object indicates the 2nd Index of the table.
I32 ifTeQosIdx3	1.3.6.1.4.1.164.6.3.3.1.1.3	Integer32	not-accessible	This object indicates the 3rd Index of the table.
I32 intSwdlFileIdx	1.3.6.1.4.1.164.6.2.12.10.1.2	Integer32	read-only	The index of the files included in intSwdlObjIdx. One of these files can be selected to be internally downloaded.
I32 intSwdlFlashIdx	1.3.6.1.4.1.164.6.2.12.10.1.10	Integer32	read-only	The index of the flash memory this file is stored in (1 or 2) (Example: 1= The file is stored in flash No.1). ASMi52 file will always be stored in Flash No.2 (intSwdlFlashIdx=2).
I32 intSwdlObjIdx	1.3.6.1.4.1.164.6.2.12.10.1.1	Integer32	read-only	The index of the object from which down-load is performed.
I32 invNameXCIndex	1.3.6.1.4.1.164.6.2.41.1.3	Integer32	read-only	The XC Table (invNameXCType) may include more than one index. This object represents the value of the first XC Index.
I32 ip2IfBandWidth	1.3.6.1.4.1.164.3.1.6.7.1.1.26	Integer32	read-create	Defines the Bandwidth of the bundle. For TDM bundles - it is the Number of Time Slots in The Bundle. - For T1 the value will be: 1..24 - For E1 the value will be: 1..31 - For T3 the value will be: 1..84 - For E3 the value will be: 1..63 This parameter is required for devices like Emux where the bandwidth of the bundles is unknown. The bundles that are received should be transmitted without any change in the bandwidth. It is the user's responsibility to enter the correct bandwidth. For Ethernet bundles - it is the bandwidth, measured in Kbps.
I32 ip2IfBundleUsage	1.3.6.1.4.1.164.3.1.6.7.1.1.18	Integer32	read-only	The Bundle Resource usage in Kbps.
I32 ip2IfCallerIdDelay	1.3.6.1.4.1.164.3.1.6.7.1.1.44	Integer32	read-create	Time in msec between CLID (Caller ID) signal detection on the line and CLID signal transmission. The CLID must be sent between ringing signals and the value of the delay is used for synchronizing the CLID transmission with the ringing signals transmission. Valid values: 0 - 3000 msec.
I32 ip2IfCallerIdRxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.89	Integer32	read-create	The gain value in dBm units of the Caller ID signal received on the bundle.
I32 ip2IfCallerIdTxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.88	Integer32	read-create	The gain value in dBm units used for transmitting the Caller ID signal on the bundle.
I32 ip2IfChannelIndex	1.3.6.1.4.1.164.3.1.6.7.1.1.1	Integer32	read-only	The channel index, which is actualy the bundle ID.
I32 ip2IfConnCheckPktFrequency	1.3.6.1.4.1.164.3.1.6.7.1.1.32	Integer32	read-create	Time in sec. between 2 Bundle Connectivity Check packets. Valid values: 0..60. 0 = Not Applicable.
I32 ip2IfConnPktTimeOutCycles	1.3.6.1.4.1.164.3.1.6.7.1.1.33	Integer32	read-create	No. of cycles the agent will send Bundle Connectivity packets without receiving a response from the remote device before declaring that the bundle connection to the remote side is down - Time Out. Valid values: 0..5. 0 = Not Applicable.
I32 ip2IfCurrentStatMaxDelayVar	1.3.6.1.4.1.164.3.1.6.7.10.1.4	Integer32	read-only	The maximum deviation from the center of the buffer (in msec) for the current interval.
I32 ip2IfDestPort	1.3.6.1.4.1.164.3.1.6.7.1.1.7	Integer32	read-create	The destination Bundle at the far-end device.
I32 ip2IfExitChannel	1.3.6.1.4.1.164.3.1.6.7.1.1.66	Integer32	read-create	The channelized bundle that the voice bundle exits through. In Gmux2000 it is the ifIndex of the Channelized Bundle (sub-channel) that the Voice Bundle exits through. The ifIndex contains the Slot+Prt+Channelized Bundle No.
I32 ip2IfFarEndTdmStatus	1.3.6.1.4.1.164.3.1.6.7.7.1.14	Integer32	read-only	This variable indicates the Status of the Far-End TDM Line. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The farEndTdmNoDefect must be set if and only if no other flag is set. The various bit positions are: 1 farEndTdmNoDefect 2 farEndTdmAIS Alarm Indication Signal 4 farEndTdmRDI Remote Defect Indication
I32 ip2IfIntervalStatIndex	1.3.6.1.4.1.164.3.1.6.7.11.1.1	Integer32	read-only	The Interval index, which is actualy the Interval number.
I32 ip2IfIntervalStatMaxDelayVar	1.3.6.1.4.1.164.3.1.6.7.11.1.5	Integer32	read-only	The maximum size of the buffer (in 10's of usec) in the selected interval.
I32 ip2IfJitterBuffer	1.3.6.1.4.1.164.3.1.6.7.1.1.9	Integer32	read-create	The maximum cell arrival jitter in 10 usec that the reassembly process will tolerate in the cell stream, without producing errors on the CBR service interface. For KM2100: KML.11 - The range that will be used is 3...300 msec in steps of 1 msec. For Vmux: The range that will be used is 20...100 msec in steps of 10 msec.
I32 ip2IfMaxRelayModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.68	Integer32	read-create	Maximum Relay modem calls for this bundle.
I32 ip2IfMaxVBDModemCalls	1.3.6.1.4.1.164.3.1.6.7.1.1.67	Integer32	read-create	Maximum VBD modem calls for this bundle.
I32 ip2IfMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.1.1.27	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
I32 ip2IfMinPowerLevel	1.3.6.1.4.1.164.3.1.6.7.1.1.40	Integer32	read-create	Indicates the minimum power level in dBm of the MF (Multi Frequency) tone transmitted by the switch. Valid values: -1...-35 dBm.
I32 ip2IfMinPulseWidth	1.3.6.1.4.1.164.3.1.6.7.1.1.39	Integer32	read-create	Indicates the minimum width in milliseconds of the MF (Multi Frequency) tone transmitted by the switch. Valid values: 45-300 msec. notApplicable=0.
I32 ip2IfMplsRxLabel	1.3.6.1.4.1.164.3.1.6.7.1.1.49	Integer32	read-create	This MIB object defines the MPLS Rx. Label for this Bundle.
I32 ip2IfMplsTxExpBits	1.3.6.1.4.1.164.3.1.6.7.1.1.52	Integer32	read-create	The MPLS Network priority (EXP bits) used for this bundle.
I32 ip2IfMplsTxLabel	1.3.6.1.4.1.164.3.1.6.7.1.1.51	Integer32	read-create	This MIB object defines the MPLS Tx. Label for this Bundle.
I32 ip2IfPortIndex	1.3.6.1.4.1.164.3.1.6.7.9.1.1	Integer32	read-only	The Port index, which is actualy the ifIndex.
I32 ip2IfPortTotalThroughput	1.3.6.1.4.1.164.3.1.6.7.9.1.4	Integer32	read-only	This parameter indicates the total Throughput of the port in bps.
I32 ip2IfPortUsage	1.3.6.1.4.1.164.3.1.6.7.9.1.2	Integer32	read-only	This parameter indicates the usage of the port (percents).
I32 ip2IfPulseMeterPeriod	1.3.6.1.4.1.164.3.1.6.7.1.1.63	Integer32	read-create	Duration of synthesized pulse metering. current values are: 100-250.
I32 ip2IfRateLimit	1.3.6.1.4.1.164.3.1.6.7.8	Integer32	read-write	The maximum rate permitted to transfer via the network portin Mbps.
I32 ip2IfRxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.71	Integer32	read-create	Receive gain in dBm.
I32 ip2IfSrcPort	1.3.6.1.4.1.164.3.1.6.7.1.1.37	Integer32	read-create	The source Bundle at the local device, this parameter used for cases where there is no match between ip2IfChannelIndex and the Source Bundle ID.
I32 ip2IfStatBufOverflows	1.3.6.1.4.1.164.3.1.6.7.7.1.4	Integer32	read-only	Number of events that the buffer overflows. This records the count of the number of events the Receive (Eth to TDM) buffer overflows.
I32 ip2IfStatBufUnderflows	1.3.6.1.4.1.164.3.1.6.7.7.1.3	Integer32	read-only	Number of events that the buffer underflows. This records the count of the number of events the Receive (Eth to TDM) buffer underflows. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
I32 ip2IfStatChIndex	1.3.6.1.4.1.164.3.1.6.7.7.1.1	Integer32	read-only	The channel index, which is actualy the bundle ID.
I32 ip2IfStatFrameTrackLongSerMiss	1.3.6.1.4.1.164.3.1.6.7.7.1.27	Integer32	read-only	The longest series of consecutive missing sequential numbers. Missing sequential numbers represent missing packets that was expected to be received successively.
I32 ip2IfStatRxMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.7.1.29	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the received payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
I32 ip2IfStatSeqErrors	1.3.6.1.4.1.164.3.1.6.7.7.1.2	Integer32	read-only	Number of events that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state.
I32 ip2IfStatTxMeasuredSilence	1.3.6.1.4.1.164.3.1.6.7.7.1.28	Integer32	read-only	This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
I32 ip2IfTDMBytesInFrame	1.3.6.1.4.1.164.3.1.6.7.1.1.11	Integer32	read-create	The number of TDM bytes to be placed in a single IP frame payload. For ip2IfTDMoIpMode = cesOverPsn this parameter indicates the number of IP frames, calculated as: 1440/.
I32 ip2IfTDMFrameBytes	1.3.6.1.4.1.164.3.1.6.7.2	Integer32	read-write	The number of TDM bytes to be placed in a single IP frame payload.
I32 ip2IfTimeElapsed	1.3.6.1.4.1.164.3.1.6.7.1.1.21	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
I32 ip2IfToneAckInterval	1.3.6.1.4.1.164.3.1.6.7.1.1.54	Integer32	read-create	Time Interval in milli seconds from the time a Vmux sends tone/s to a local PBX until it receives an acknowledgement from this PBX. Valid values: 60...400 in steps of 20.
I32 ip2IfTos	1.3.6.1.4.1.164.3.1.6.7.1.1.10	Integer32	read-create	The TOS (Type of Service) value: 0..255. In Vmux-2100/110 devices versions 3.1 and up, in Vmux-210 and in Vmux-4x0: LSB 8 bits - 00 00 00 XX will be used for Signaling packets TOS. Next 8 bits - 00 00 XX 00 will be used for Media packets TOS. Next 16 bits - will be 0. XX = Hex values: 0..FF For mixed packets, TOS of Media Packets will be used. Signaling packets are for example: Keep alive packets and ABCD signaling bits. Media packets are for example: voice, fax, HDLC, payload packets.
I32 ip2IfTosValue	1.3.6.1.4.1.164.3.1.6.7.3	Integer32	read-write	The TOS value to write in the IP frame.
I32 ip2IfTxGain	1.3.6.1.4.1.164.3.1.6.7.1.1.35	Integer32	read-create	Transmit gain in dBm.
I32 ip2IfValidIntervals	1.3.6.1.4.1.164.3.1.6.7.1.1.22	Integer32	read-only	The number of previous intervals for which data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute intervals since the interface has been online.
I32 ip2IfVlanFramePriority	1.3.6.1.4.1.164.3.1.6.7.1.1.14	Integer32	read-create	VLAN Frame priority.
I32 ip2IfVlanID	1.3.6.1.4.1.164.3.1.6.7.5	Integer32	read-write	VLAN ID.
I32 ip2IfVlanIdentifier	1.3.6.1.4.1.164.3.1.6.7.1.1.13	Integer32	read-create	VLAN ID.
I32 ip2IfVlanPriority	1.3.6.1.4.1.164.3.1.6.7.6	Integer32	read-write	Frame priority.
I32 linkSelectorCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 linkSelectorMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.17.2.1.4	Integer32	read-write	Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=move immediately to higher prioritized connected link. UNIT is seconds.
I32 linkSelectorMinBUSession	1.3.6.1.4.1.164.3.2.3.2.17.2.1.7	Integer32	read-write	Minimum duration of a backup session before returning to Main Link. Relevant in Backup Mode and when Revert is auto(2). Value 255 is for NEVER which means never return to Main Link. UNIT is minutes.
I32 linkSelectorPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.2.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be internal port number: higher or equal to linkSeL1(201).
I32 mapLinkId	1.3.6.1.4.1.164.3.1.5.1.1.1	Integer32	read-only	A unique identifier of the link
I32 mapLinkIdx	1.3.6.1.4.1.164.3.3.4.2.1.1	Integer32	read-only	A unique identifier of the link
I32 mapLinkPortIdx	1.3.6.1.4.1.164.3.3.4.2.1.3	Integer32	read-write	This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 maskingCurrentEntries	1.3.6.1.4.1.164.4.1.6.2	Integer32	read-only	The number of entries in the mask table.
I32 maskingHighLevelProt	1.3.6.1.4.1.164.4.1.6.3.1.18	Integer32	read-write	This field is set in connection to the maskingProtocolType variable. This variable specifies the high level protocols (application). As for today it supports just IP protocol stack. The object's value is a sum of the following instances values (selected by user): none (0), -- don't care ftp (1), ftpC (2), telnet (4), smtp (8), tftp (16), snmp (32), snmpTrap (64), ipRip (128), www (256), email (512), dns (1024), For Apple Protocol only: rtmp (2048), nbp (4096), atp (8192), aep (16384), zip (32768), adsp (65536), pap (131072), asp (262144) Example: if ftp(1), snmp(32) and snmpTrap(64) instances were selected, the value should be 97 (=1+32+64).
I32 maskingIfIndex	1.3.6.1.4.1.164.4.1.6.3.1.2	Integer32	read-only	Specifies the ifIndex of the interface to which the mask is applied.
I32 maskingIndex	1.3.6.1.4.1.164.4.1.6.3.1.3	Integer32	read-only	An index to the masking table. This number should not be greater than maskingMaxEntries
I32 maskingMaxEntries	1.3.6.1.4.1.164.4.1.6.1	Integer32	read-only	The maximum number of entries in the masking table.
I32 maskingPortNum	1.3.6.1.4.1.164.4.1.6.3.1.20	Integer32	read-write	The port number is the same as in high level protocol. It specifies the dest. port in IP case or the dest. socket in case of IPX & apple protocols. IP - This object is applicable only if none (0) value was selected in maskingHighLevelProt. IPX - This object is applicable only if the socket entered in maskingDestAddress is 'don't care'(00) AND maskingLowLevelProt is NOT ipxRip or ipxSap. Apple - This option is applicable only if the socket entered in maskingDestAddress is 'don't care'(00).
I32 maskingSrcPortNum	1.3.6.1.4.1.164.4.1.6.3.1.23	Integer32	read-write	The source port number. For IP: No Condition. For IPX: This object is applicable only if the socket entered in maskingSourceAddress is don't care (00) and maskingLowLevelProt is NOT ipxRip or ipxSap. For Apple:This object is applicable only if the socket entered in maskingSourceAddress is don't care (00).
I32 mdlAlarmCounter	1.3.6.1.4.1.164.3.3.2.1.3.1.1.8	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
I32 mdlAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.3.3.2.1.3	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
I32 mdlAlarmsCmprAlarmSlot	1.3.6.1.4.1.164.3.1.3.3.2.1.2	Integer32	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid.
I32 mdlAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.3.3.2.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 mdlAlrCode	1.3.6.1.4.1.164.3.3.2.1.3.1.1.3	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
I32 mdlAlrIdx	1.3.6.1.4.1.164.3.3.2.1.3.1.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive
I32 mdlCCnfgIdx	1.3.6.1.4.1.164.3.1.3.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..100) being referred. Value 255 specifies the TmpCnfg
I32 mdlCConfigIdx	1.3.6.1.4.1.164.3.3.2.1.2.1.1	Integer32	read-only	This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch).
I32 mdlClSwchStatus	1.3.6.1.4.1.164.3.3.2.2.1.1.2	Integer32	read-only	This object indicates the status of the switches on the referred DCL card. Each switch is represented by a bit. The status is a sum of 2n, according to the bits. There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (21 + 2**0). When the status of the switches is unknown, the value of this object will be 255.
I32 mdlCmprCnfgIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 mdlCmprTypIdx	1.3.6.1.4.1.164.3.1.3.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 mdlCmprVersion	1.3.6.1.4.1.164.3.1.3.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 mdlCNoOfExternPrt	1.3.6.1.4.1.164.3.1.3.2.1.1.4	Integer32	read-only	Number of external ports in the programmed card of the specific slot position
I32 mdlCNoOfExtPrt	1.3.6.1.4.1.164.3.3.2.1.2.1.4	Integer32	read-only	Number of external ports in the programmed module of the specific slot position
I32 mdlCNoOfInternPrt	1.3.6.1.4.1.164.3.1.3.2.1.1.5	Integer32	read-only	Number of internal ports in the programmed card of the specific slot position.
I32 mdlCNoOfIntPrt	1.3.6.1.4.1.164.3.3.2.1.2.1.5	Integer32	read-only	Number of internal ports in the programmed module of the specific slot position.
I32 mdlCParam	1.3.6.1.4.1.164.3.3.2.1.2.1.6	Integer32	read-write	General configuration object at card level (per configuration). NotApplicable=0, for cards that don't support this object. For D8U and D16U cards of DXC, the object will indicate the port on which BERT will be performed. The port can be one of the external ports, any of its associated B1, B2, D ports or no port of the card (None=0). For port indexes see DXC R6 spec. For Gmux-2000, this parameter used for determining the Gigabit ETH exit port
I32 mdlPbxFraCnfgIdx	1.3.6.1.4.1.164.3.2.2.1.1.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 mdlPbxFraTransSigTs	1.3.6.1.4.1.164.3.2.2.1.1.1.1.10	Integer32	read-write	This is the Time Slot that is used for Transparent CCS signaling. The values of this TS are 1-24 for T1 & 1-31 for E1. The default for E1 is 16 & for T1 it is 24. If no signaling is used then the TS should be 255 (None).
I32 mdlProtIpCnfgIdx	1.3.6.1.4.1.164.3.2.2.1.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being accessed. Idx 255 relates to the TmpCnfg. For Agents having several configuration, Write operation is allowed only to the Temporary Configuration.
I32 mdlSAlrCode	1.3.6.1.4.1.164.3.1.3.1.2.1.4	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at card level.
I32 mdlSAlrCounter	1.3.6.1.4.1.164.3.1.3.1.2.1.7	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
I32 mdlSAlrIdx	1.3.6.1.4.1.164.3.1.3.1.2.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive.
I32 mdlSCmd	1.3.6.1.4.1.164.3.3.2.1.1.1.13	Integer32	read-write	General object for any special command at card level. 0=NotApplicable, for cards that don't support this object. For KML.10(ISDN) card of KM-2100, the object will indicate Manual Call Command in Switch mode. It is applicable only when for KML.10, prtIsdnSwitchMode=manual. KML.10 valid values: '1' = noOp, will be used by agents that do not support this feature or object (old KM agents) '2' = off, Set call command mode to disconnect state. Disconnects the call. '3' = on, Set call command mode to connect state. Connects the call. For DXC IO cards, the object will be used for IO Card Reset HW command: '2' = off, this will be always the Get value for these cards. '3' = on, this is the Set command used to Reset the IO card. Upon completing the operation, the value will automatically change to off(2), by Agent. For Slots that are NOT IO Slots and for empty IO Slots, the Get value will be always '0' (NotApplicable).
I32 mdlSTemperature	1.3.6.1.4.1.164.3.1.3.1.1.1.12	Integer32	read-only	Temperature of the card, in Celsius degrees.
I32 mngID	1.3.6.1.4.1.164.6.2.7.1.1	Integer32	read-only	This value indicates an index of a specific IP address
I32 mngTrapMask	1.3.6.1.4.1.164.6.2.7.1.4	Integer32	read-write	The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
I32 modlParamIndex	1.3.6.1.4.1.164.6.2.32.1.1.1.1	Integer32	read-only	The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4.
I32 optPrtMonitorLaserBias	1.3.6.1.4.1.164.6.2.15.8.1.1.4	Integer32	read-only	LASER bias current level. Value is given in units of microAmper (uA).
I32 optPrtMonitorLaserTemp	1.3.6.1.4.1.164.6.2.15.8.1.1.5	Integer32	read-only	LASER temperature level, in hundredth (1/100) (C) degrees.
I32 optPrtMonitorPrtIdx	1.3.6.1.4.1.164.6.2.15.8.1.1.1	Integer32	not-accessible	This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
I32 optPrtMonitorRxPower	1.3.6.1.4.1.164.6.2.15.8.1.1.6	Integer32	read-only	Received optical power in units of hundredth (1/100) of dBm.
I32 optPrtMonitorSupplyVoltage	1.3.6.1.4.1.164.6.2.15.8.1.1.7	Integer32	read-only	Supply voltage, in hundredth (1/100) of volts (V).
I32 optPrtMonitorTxPower	1.3.6.1.4.1.164.6.2.15.8.1.1.3	Integer32	read-only	Transmitted optical power level. Value is given in units of hundredth (1/100) of dBm.
I32 pLinkCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 pLinkIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.4	Integer32	read-only	This index is the row number.
I32 pLinkPortNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.6	Integer32	read-write	The port of the prioritized link. Value 100 is for noConnect.
I32 pLinkPrioNu	1.3.6.1.4.1.164.3.2.3.2.17.3.1.7	Integer32	read-write	The priority of the prioritized link. MIN=1...., MAX=8.
I32 pLinkPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.3.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be the link selector number.
I32 portIdx	1.3.6.1.4.1.164.6.2.15.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
I32 portTrafficClass	1.3.6.1.4.1.164.6.3.5.1.1.3	Integer32	read-write	This object indicates the Traffic Class level of this port.
I32 portTrafficClassIdx1	1.3.6.1.4.1.164.6.3.5.1.1.1	Integer32	not-accessible	This attribute indicates the 1st index of the table. This may be the Idx of the Cnfg(1..255) being accessed; Idx of 255 relates to the TmpCnfg, or any other Index.
I32 portTrafficClassPortIdx	1.3.6.1.4.1.164.6.3.5.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
I32 prtAcmCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.20.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
I32 prtAgendaBehaviourCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtAgendaBehaviourPrtIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.3	Integer32	read-only	This parameter should be: - port number for MX300/30 - 100 = N/A for MX3000.
I32 prtAgendaBehaviourSltIdx	1.3.6.1.4.1.164.3.1.4.2.2.1.1.2	Integer32	read-only	This parameter should be: - slot number for MX3000 - 255 = N/A for MX300/30.
I32 prtAlarmsCmprAlarmIdx	1.3.6.1.4.1.164.3.1.4.3.3.1.4	Integer32	read-only	A unique number to identify an entry in the alarm status table of the agent.
I32 prtAlarmsCmprAlarmPort	1.3.6.1.4.1.164.3.1.4.3.3.1.3	Integer32	read-only	This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a non-existing port. IP Bundles are considered a port too, for this matter.
I32 prtAlarmsCmprAlarmSlot	1.3.6.1.4.1.164.3.1.4.3.3.1.2	Integer32	read-only	This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For Stand-alone units, notApplicable(255) will appear.
I32 prtAlarmsCmprVersion	1.3.6.1.4.1.164.3.1.4.3.3.1.1	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 prtAlrMaskPrtIdx	1.3.6.1.4.1.164.3.3.3.1.4.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtBdbandCnfgIdx	1.3.6.1.4.1.164.3.1.6.8.1.1.1.1	Integer32	read-only	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
I32 prtBdbandIdx	1.3.6.1.4.1.164.3.1.6.8.1.1.1.2	Integer32	read-only	This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.
I32 prtBertCounter	1.3.6.1.4.1.164.6.2.15.4.1.1.3	Integer32	read-only	This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counter starts from zero (0) anytime BERT is initiated.
I32 prtBertErrorBits	1.3.6.1.4.1.164.3.3.3.1.5.1.9	Integer32	read-only	How many Error Bits were detected since BERT started to run.
I32 prtBertESs	1.3.6.1.4.1.164.3.3.3.1.5.1.7	Integer32	read-only	How many Errored Seconds were detected since BERT started to run. Counter for Kmux and MP.
I32 prtBertPrtIdx	1.3.6.1.4.1.164.3.3.3.1.5.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the MP : - first two digits will be: (IO slot number+10) - last one/two digits will be according to the external port number within the card: exPrt1 -> 1 exPrt2 -> 3 exPrt3 -> 5 exPrt4 -> 7 .
I32 prtBertRunTime	1.3.6.1.4.1.164.3.3.3.1.5.1.6	Integer32	read-only	This object indicates how much time (seconds) passed since BERT started to run.
I32 prtBertRxBits	1.3.6.1.4.1.164.3.3.3.1.5.1.15	Integer32	read-only	How many data bits were Received since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
I32 prtBertSyncLoss	1.3.6.1.4.1.164.3.3.3.1.5.1.8	Integer32	read-only	How many times Sync Loss was detected since BERT started to run. For some products: number of seconds in which Sync Loss occured since BERT started to run. See product specification.
I32 prtBertTxBits	1.3.6.1.4.1.164.3.3.3.1.5.1.14	Integer32	read-only	How many data bits were transmitted since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
I32 prtBertTxErrorBits	1.3.6.1.4.1.164.3.3.3.1.5.1.16	Integer32	read-only	Number of injected error bits since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
I32 prtCfgParamCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.7.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtCfgParamIdx	1.3.6.1.4.1.164.3.3.3.1.7.1.1.2	Integer32	read-only	A unique identifier of the port (within the card when applicable). - For KM-2100: Slot*100+Ch external ports: Ch=1..10 internal ports (sub-channels): Ch=11..20. - For FCD-T1/E1(L): MAIN=111, SUB=113, CH1=122, CH2=124. - For other devices, see specific device's spec.
I32 prtClkSrcCnfgIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
I32 prtClkSrcPrt	1.3.6.1.4.1.164.6.2.15.7.1.1.5	Integer32	read-write	This entry is valid only when working in rxClk mode. It specifies the port from which the clock willl be taken. Refer to device specification for source port Index
I32 prtClkSrcPrtIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index (receiving clock). Refer to device specification for port Index
I32 prtCmprCnfgIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.2	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 prtCmprPrtIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.5	Integer32	read-only	This attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148).
I32 prtCmprTypIdx	1.3.6.1.4.1.164.3.1.4.3.1.1.1	Integer32	read-only	This attribute indicates the Type of the Compressed being referred.
I32 prtCmprVersion	1.3.6.1.4.1.164.3.1.4.3.1.1.3	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 prtCnfgAgendaCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtCnfgAgendaFrom	1.3.6.1.4.1.164.3.1.4.2.2.2.1.6	Integer32	read-write	Start from time interval in seconds.
I32 prtCnfgAgendaPrtIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.3	Integer32	read-only	This attribute is equal to: - port number for MX300/30 - port number for MX3000. For example 1-4 in MHS-4 cards. - 100 = N/A for MX3000 when not used.
I32 prtCnfgAgendaSesId	1.3.6.1.4.1.164.3.1.4.2.2.2.1.5	Integer32	read-only	The user may define 4 different active intervals per day.
I32 prtCnfgAgendaSltIdx	1.3.6.1.4.1.164.3.1.4.2.2.2.1.2	Integer32	read-only	This attribute is equal to: -slot number for MX3000 -255 = N/A for MX300/30
I32 prtCnfgAgendaTo	1.3.6.1.4.1.164.3.1.4.2.2.2.1.7	Integer32	read-write	To time interval in seconds.
I32 prtControlCnfg	1.3.6.1.4.1.164.6.2.15.5.1.1.2	Integer32	read-write	This object may be used for port RW general parameter/s. For detailed meaning, see product's spec. Supported by: PRBi-E3/T3. For ACE2002: This parameter will include the value of the new index generated by agent. For Optimux-T3 and OP-155-1: This parameter will be used for Release Remote LLB Command: on=2= Set value only. Command to release LLB of Remote Unit. Agent will return automatically to 'off' value after performing the command. off=3=Get value only. For LA140 This parameter will be used as EchoCanceler per timeslot off = 2 Echo Canceler is disabled on = 3 Echo Canceler is enabled For FCD-155 This parameter will be used to select the port that is clock source for a PDH port, For E1/T1 PDH VC12/VT1.5 = 2 SDH/SONET = 3 For E3/T3 PDH VC3/DS3 = 2 SDH/SONET = 3 For ACE-52 This parameter will be used as Transmit Frame Type, i.e. which type of frame the corresponding bridge port will transmit: Untagged = 2 Tagged = 3 .
I32 prtCrTimeElapsed	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.4	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0.
I32 prtDest	1.3.6.1.4.1.164.3.3.3.5.2.1.4	Integer32	read-write	Destination port,(of a T1/E1 port), that is connected to the DIM card, for the specified Destination number. 0 = No destination port. Else: For external ports: (IO Slot+10) & 1 for port 1 (IO Slot+10) & 3 for port 2 Example: port2 of IO slot 12 will be: 223 . For internal ports : (IO Slot+10) & 2 for port 1 (IO Slot+10) & 4 for port 2 (IO Slot+10) & 6 for port 3 (IO Slot+10) & 8 for port 4, etc...
I32 prtDestCnfgIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
I32 prtDestDimIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.2	Integer32	read-only	This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10) & 1 Example: port1 of IO slot 11 will be: 211 .
I32 prtDestIdx	1.3.6.1.4.1.164.3.3.3.5.2.1.3	Integer32	read-only	This attribute indicates a destination number of the DIM card.
I32 prtDimCnfgIdx	1.3.6.1.4.1.164.3.3.3.5.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
I32 prtDimIdx	1.3.6.1.4.1.164.3.3.3.5.1.1.2	Integer32	read-only	This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10)*10 + 1 Example: port1 of IO slot 11 will be: 211 .
I32 prtDlciCmprCnfgIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.1	Integer32	read-only	This attribute indicates the configuration to which the Compressed information is related.
I32 prtDlciCmprDlciIdx	1.3.6.1.4.1.164.3.1.4.3.2.1.5	Integer32	read-only	This attribute indicates a unique identifier of the Dlci the compressed information relates to. The values are between 16 - 991.
I32 prtDlciCmprVersion	1.3.6.1.4.1.164.3.1.4.3.2.1.2	Integer32	read-only	This attribute indicates the version of the internal format of the Compressed data
I32 prtDlciIdx	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.3	Integer32	read-only	This attribute indicates a unique DLCI index for each valid DLCI (16..991).
I32 prtDs3IfTimeElapsed	1.3.6.1.4.1.164.3.1.6.3.1.1.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
I32 prtDs3IfValidIntervals	1.3.6.1.4.1.164.3.1.6.3.1.1.1.2	Integer32	read-only	The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
I32 prtDs3IntervalNumber	1.3.6.1.4.1.164.3.1.6.3.1.3.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
I32 prtE2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.21.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
I32 prtExClCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.1.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExHs4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.7.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExHs4IdleCode	1.3.6.1.4.1.164.3.2.3.2.7.1.1.11	Integer32	read-write	Type value(00 - FF HEX), excluding 0H,8H,10H,12H,21H,24H, 42H,49H,84H,92H
I32 prtExHs4TsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExHs4TsIConTs	1.3.6.1.4.1.164.3.2.3.2.7.2.1.7	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Module and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
I32 prtExHs4TsIdx	1.3.6.1.4.1.164.3.2.3.2.7.2.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling.
I32 prtExHsiCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExHsiPrtIdx	1.3.6.1.4.1.164.3.2.3.2.8.1.1.3	Integer32	read-only	A unique port identifier within the card. For MP : 1..12 For DXC: 111 .. 2531. See DXC R6 spec for port index convention. For FCD-A, 'S' Interface external ports: 131, 141, 151, 161.
I32 prtExHsrCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExHsrPrtIdx	1.3.6.1.4.1.164.3.2.3.2.10.1.1.3	Integer32	read-only	A unique prt identifier within the card. Valid values: For MP: - For HS-R cards: exPrt1 (1) .. exPrt4 (4) - For HS-U/1 cards: inPrt1 (101) .. inPrt4 (104) - For HS-S12, HS-S6, HS-U12, HS-U6 cards: exPrt1 (1) .. exPrt12 (12). This MIB table is used only for LT-1 interface. For DXC: - For HS-U8, HS-U16 cards: 111 .. 2531 (See DXC R6 spec for port index convention). This MIB table is used only for LT-1 interface.
I32 prtExLs2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExLs2EnvIdx	1.3.6.1.4.1.164.3.2.3.2.4.1.1.9	Integer32	read-write	Envelope Index. When prtInLs2EnvAssign=auto, the value is 0 (not applicable).
I32 prtExLs6CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExLs6VCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExLs6VRxGain	1.3.6.1.4.1.164.3.2.3.2.13.2.1.9	Integer32	read-write	Receive gain in dBm. E&M - values range: -17 .. 2 FXO - values range: -17 .. -1 FXS - values range: -17 .. 2
I32 prtExLs6VTxGain	1.3.6.1.4.1.164.3.2.3.2.13.2.1.8	Integer32	read-write	Transmit gain in dBm. E&M - values range: -17 .. 8 FXO - values range: -16 .. 4 FXS - values range: -13 .. 8
I32 prtExMbeCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.11.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExPh1MlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExPh1MlFragmentSize	1.3.6.1.4.1.164.3.2.3.2.2.1.1.32	Integer32	read-write	This parameter indicates the maximum number of bytes permitted in a packet send over the Link. Exceeding this size will cause packet fragmentation.
I32 prtExPh1MlIdleCode	1.3.6.1.4.1.164.3.2.3.2.2.1.1.11	Integer32	read-write	Determines the code for transmission in empty time slots. Type value(00-FFH), Excluding 0H,8H,10H,12H,21H,24H,42H,49H, 84H,92H
I32 prtExPh1MlRedundRecTime	1.3.6.1.4.1.164.3.2.3.2.2.1.1.22	Integer32	read-write	Redundancy Recovery Time (sec). After switching the ML card to the current (prtExPh1MlSltIdx), the next ML switch can be performed only after a minimum time, indicated by this object.
I32 prtExPh1MlSupportedTS	1.3.6.1.4.1.164.3.2.3.2.2.1.1.26	Integer32	read-only	Number of Supported Time Slots by the agent. For Vmux-110 there is HW that supports less than 31/24 Time Slots for the E1/T1 port.
I32 prtExPh1MlTsBundle	1.3.6.1.4.1.164.3.2.3.2.2.2.1.11	Integer32	read-write	The number of the bundle containing this Time Slot. If no bundle exists for this TS or the bundle number is irrelevant, the value will be 0.
I32 prtExPh1MlTsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExPh1MlTsIConPrt	1.3.6.1.4.1.164.3.2.3.2.2.2.1.6	Integer32	read-write	This attribute indicates the internally (In Mux) connected/routed port. For MP, the values will be: { exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , noConnect (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109) , inPrt10 (110) , inPrt11 (111) , inPrt12 (112) } For other products see specific values at spec.
I32 prtExPh1MlTsIConTs	1.3.6.1.4.1.164.3.2.3.2.2.2.1.7	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated to multiframe synchronization and voice signaling.
I32 prtExPh1MlTsIdx	1.3.6.1.4.1.164.3.2.3.2.2.2.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
I32 prtExPh1MlTsSubChMask	1.3.6.1.4.1.164.3.2.3.2.2.2.1.14	Integer32	read-write	The Sub-Channel Type Mask. This variable is relevant only when Time-Slot Type is SubCh (e.g. prtExPh1MlTsType = subCh1...subCh8).
I32 prtExPh1MlTsTestDuration	1.3.6.1.4.1.164.3.2.3.2.2.2.1.12	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific TS. This entry applies to all the test operations. For the Vmux2100 the values are: 0 - 60 seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtExPh1MlTsTest' parameter.
I32 prtExPhPlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExPhPlCongLevel	1.3.6.1.4.1.164.3.2.3.2.3.1.1.12	Integer32	read-write	This attribute indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5 percent.
I32 prtExPhPlDlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExPhPlDlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.3.2.1.8	Integer32	read-write	This attribute indicates a unique internal connection dlci number, the dlci is routed to.
I32 prtExPhPlDlciIdx	1.3.6.1.4.1.164.3.2.3.2.3.2.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, its type is 'user' and the only valid index is 1.
I32 prtExPhPlDlciPriority	1.3.6.1.4.1.164.3.2.3.2.3.2.1.13	Integer32	read-write	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority.
I32 prtExPhPlEnqPeriod	1.3.6.1.4.1.164.3.2.3.2.3.1.1.23	Integer32	read-write	This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlErrorsThreshold	1.3.6.1.4.1.164.3.2.3.2.3.1.1.26	Integer32	read-write	This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlFrWindowSize	1.3.6.1.4.1.164.3.2.3.2.3.1.1.25	Integer32	read-write	This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlFullRptPeriod	1.3.6.1.4.1.164.3.2.3.2.3.1.1.24	Integer32	read-write	This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
I32 prtExPhPlIdleCode	1.3.6.1.4.1.164.3.2.3.2.3.1.1.34	Integer32	read-write	Determines the code for transmission when there are no frames to transmit on the line. The value should be 0 to FFH.
I32 prtExPhPlJitter	1.3.6.1.4.1.164.3.2.3.2.3.1.1.35	Integer32	read-write	Maximum variant delay of the FR network, in msec.
I32 prtExPhPlLXoff	1.3.6.1.4.1.164.3.2.3.2.3.1.1.21	Integer32	read-write	This attribute indicates the character used as X-Off to notify receive disable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable
I32 prtExPhPlLXon	1.3.6.1.4.1.164.3.2.3.2.3.1.1.20	Integer32	read-write	This attribute indicates the character used as X-On to notify receive enable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable
I32 prtExPhPlMinSeparators	1.3.6.1.4.1.164.3.2.3.2.3.1.1.31	Integer32	read-write	Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable
I32 prtExPhPlModemCallDelay	1.3.6.1.4.1.164.3.2.3.2.3.3.1.8	Integer32	read-write	Time in Seconds that the device will wait before dialing to the remote device. This feature is mostly used when there is a backup modem to the main link and the main link is down. In this case it is important to prevent the 2 devices from dialing through the backup modems to each other at the same time. It is advised to configure one side with a small call delay and the other side with a large call delay. Legal Values are: 0 - 30, 60, 120, 180, 240, 300, 600, 900, 1200, 1500, 1800 . 65535 sec. means that this parameter is not applicable. Default: 0 sec
I32 prtExPhPlModemCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.3.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExPhPlModemMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.3.3.1.6	Integer32	read-write	Max Time allowed in Seconds without any traffic before the line is disconnected. Legal Values are: 1 sec, 2 sec .. 5 sec, 10 sec, 20 sec.. 1 min, 2 min .. 10 min, 15 min, 20 min, 25 min, 30 min. 65535 sec. means that this parameter is not applicable. Default: 1 sec.
I32 prtExPhPlModemTimeBtwnCalls	1.3.6.1.4.1.164.3.2.3.2.3.3.1.7	Integer32	read-write	Minimum Time in Seconds which is required after a call was disconnected. In this time no other call will be initiated from this Modem port even if there were frames transmitted to this port. This time is required for some Modems which have initializations that take a few seconds. Legal Values are: 0 sec. - 30 sec., 1-5 min. 65535 sec. means that this parameter is not applicable. Default: 0 sec
I32 prtExPVc4ChannelId	1.3.6.1.4.1.164.3.2.3.2.9.1.1.31	Integer32	read-write	Channel Identifier. According to FRF11 each voice port that works as force connect should add a CH Id after the DLCI in the frame header. Default : 1 Applicable only for Force Connect. Not Applicable value will be 0.
I32 prtExPVc4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExPVc4CongLevel	1.3.6.1.4.1.164.3.2.3.2.9.1.1.14	Integer32	read-write	This object indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5%.
I32 prtExPVc4DelayStart	1.3.6.1.4.1.164.3.2.3.2.9.1.1.25	Integer32	read-write	This parameter is used only for Delay Protocol. This is the time that the calling party will wait after sending an Off hook signal and before sending DTMF digits to the called party. The delay values are 100..5000 msec in intervals of 100 msec.
I32 prtExPVc4DestBundle	1.3.6.1.4.1.164.3.2.3.2.9.1.1.48	Integer32	read-write	This object defines the destination Bundle at the far-end device.
I32 prtExPVc4DiscOnSilence	1.3.6.1.4.1.164.3.2.3.2.9.1.1.36	Integer32	read-write	No. of silenced seconds after which the call will be disconected. A value of 0 means that there will be no disconnect when there is silence. Possible values: 0 - 900 sec.
I32 prtExPVc4DlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.9.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExPVc4DlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.9.2.1.7	Integer32	read-write	This attribute indicates a unique internal connection dlci number, the dlci is routed to.
I32 prtExPVc4DlciPriority	1.3.6.1.4.1.164.3.2.3.2.9.2.1.12	Integer32	read-write	This attribute indicates a unique priority of the pvc. 6 is the lowest priority and 8 is the highest priority.
I32 prtExPVc4FrameSize	1.3.6.1.4.1.164.3.2.3.2.9.1.1.40	Integer32	read-write	Defines the maximum size in Bytes of the multiplexed frame. In some cases this must be limited to avoid IP fragmentation, which makes the multiplexing useless, and can also decrease the damage in case of frame loss. Valid range: 100..1461. notApplicable=0.
I32 prtExPVc4HuntGroupIdx	1.3.6.1.4.1.164.3.2.3.2.9.1.1.20	Integer32	read-write	If it belongs to an hunt group, this fields indicates the index of the relevant hunt group. 0 = notApplicable
I32 prtExPVc4MinPowerLevel	1.3.6.1.4.1.164.3.2.3.2.9.1.1.45	Integer32	read-write	Defines the minimum Power Level in dBm. Valid values: -1..-35 dBm.
I32 prtExPVc4MinPulseWidth	1.3.6.1.4.1.164.3.2.3.2.9.1.1.44	Integer32	read-write	Defines the minimum Pulse Width in msec. Valid values: 45-100 msec. notApplicable=0.
I32 prtExPVc4MultiplexInterval	1.3.6.1.4.1.164.3.2.3.2.9.1.1.41	Integer32	read-write	Defines the maximum amout of time (msec.) between multiplexed frames that are sent. For Vmux-400/420 devices: It defines the Payload Packetizing Interval. Valid values: 10-90 msec. notApplicable=0.
I32 prtExPVc4Rate	1.3.6.1.4.1.164.3.2.3.2.9.1.1.39	Integer32	read-write	This is the Rate of the port in TS units. It is used by VF-30 card family. 0 = NA = port is not intended to be connected; therefore, no Rate.
I32 prtExPVc4RxGain	1.3.6.1.4.1.164.3.2.3.2.9.1.1.8	Integer32	read-write	Reception gain in dBm.
I32 prtExPVc4TxGain	1.3.6.1.4.1.164.3.2.3.2.9.1.1.7	Integer32	read-write	Transmission gain in dB.
I32 prtExPVc4VarDelay	1.3.6.1.4.1.164.3.2.3.2.9.1.1.13	Integer32	read-write	Maximum variant delay of the FR network, in msec.
I32 prtExPVc4WinkMaxDuration	1.3.6.1.4.1.164.3.2.3.2.9.1.1.27	Integer32	read-write	This parameter is used only for Wink Protocol. Max Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec.
I32 prtExPVc4WinkMinDuration	1.3.6.1.4.1.164.3.2.3.2.9.1.1.26	Integer32	read-write	This parameter is used only for Wink Protocol. Min Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec.
I32 prtExTreCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.12.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExTsBit	1.3.6.1.4.1.164.3.1.4.2.1.1.5	Integer32	read-only	This attribute indicates a unique Bit within the time slot. The valid Bits are: 1..8. 255=NA.
I32 prtExTsCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExTsIConPrt	1.3.6.1.4.1.164.3.1.4.2.1.1.7	Integer32	read-write	This attribute indicates the internally (In Mux) connected/routed port. For other products' index see their specification.
I32 prtExTsIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.4	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling.
I32 prtExTsPrtIdx	1.3.6.1.4.1.164.3.1.4.2.1.1.3	Integer32	read-only	This attribute indicates a unique port number. Most ML cards have only one external interface. inPrt1 - for MTML-H/E1 cards. For other products' index see their specification.
I32 prtExVc2ReceiveGain	1.3.6.1.4.1.164.3.2.3.2.5.1.6	Integer32	read-write	Receive gain in dBm. For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8 VC-4/Omni and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps.
I32 prtExVc2TransGain	1.3.6.1.4.1.164.3.2.3.2.5.1.5	Integer32	read-write	Transmit gain in dBm. For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8 VC-4/Omni and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps.
I32 prtExVc3CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.14.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExVc3ReceiveGain	1.3.6.1.4.1.164.3.2.3.2.14.1.1.6	Integer32	read-write	Receive gain in dBm.
I32 prtExVc3TransGain	1.3.6.1.4.1.164.3.2.3.2.14.1.1.5	Integer32	read-write	Transmit gain in dBm.
I32 prtExVcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtExVcPbxTransSignalTs	1.3.6.1.4.1.164.3.2.3.2.15.1.1.7	Integer32	read-write	This object specifies the ML Time-Slot dedicated to the signaling of the PABX Transparent TSs. None = 255. When prtExVcPbxTransparent=no this object's value=None (255) When prtExVcPbxTransparent=notApplicable, this object's value=None (255). When prtExVcPbxTransparent=yes: - for VC-PBX/T1 ports, this object's valid values are 1..16 or None (255). - for VC-PBX/E1 ports, this object's value will be 16 or None (255).
I32 prtExVcPbxTsCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtExVcPbxTsIConTs	1.3.6.1.4.1.164.3.2.3.2.15.4.1.8	Integer32	read-write	This attribute indicates the ML TS to which this TS is connected. This object is not applicable for VF-PBX cards. For VF-24/30/48/60 cards it is applicable only when prtExVcPbxTsMode=transparent or voiceTransparent. The valid time slots are 1..24 for ML T1 cards and 1..31 for ML E1 cards. notApplicable - 255.
I32 prtExVcPbxTsIdx	1.3.6.1.4.1.164.3.2.3.2.15.4.1.4	Integer32	read-only	This attribute indicates a unique PABX time slot position. The valid time slots are 1..24 for T1 cards and 1..31 for E1 cards.
I32 prtExVcPbxTsRemTs	1.3.6.1.4.1.164.3.2.3.2.15.4.1.10	Integer32	read-write	This attribute indicates the end-point TS on the Remote unit. The valid time slots are 1..24 for T1 ports and 1..31 for E1 ports. notApplicable - 255.
I32 prtFrPlusCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtFrPlusPrtIdx	1.3.6.1.4.1.164.3.2.3.2.18.1.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be: - for ISDN cards: inPrt1(101)->inPrt50(150) - for MHS1 card : exPrt1(1) - for MHS3, MLS3 cards: exPrt1(1)->exPrt3(3) - for MLS6 cards: exPrt1(1)->exPrt6(6).
I32 prtFrTimeElapsed	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.4	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0.
I32 prtGenCnfgIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
I32 prtGenCnfgLinkToPort	1.3.6.1.4.1.164.3.1.4.2.3.1.5	Integer32	read-write	This attribute indicates the port in the prtGenCnfgLinkToSlot of the ML card to which the IO port is mapped. For MP: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109), inPrt10 (110), inPrt11 (111), inPrt12 (112), inPrt13 (113), inPrt14 (114), inPrt15 (115), inPrt16 (116), inPrt17 (117), inPrt18 (118), inPrt19 (119), inPrt20 (120), inPrt21 (121), inPrt22 (122), inPrt23 (123), inPrt24 (124), inPrt25 (125), inPrt26 (126), inPrt27 (127), inPrt28 (128), inPrt29 (129), inPrt30 (130), inPrt31 (131), inPrt32 (132), inPrt33 (133), inPrt34 (134), inPrt35 (135), inPrt36 (136), inPrt37 (137), inPrt38 (138), inPrt39 (139), inPrt40 (140), inPrt41 (141), inPrt42 (142), inPrt43 (143), inPrt44 (144), inPrt45 (145), inPrt46 (146), inPrt47 (147), inPrt48 (148), inPrt49 (149), inPrt50 (150), inPrt51 (151), inPrt52 (152), inPrt53 (153), inPrt54 (154), inPrt55 (155), inPrt56 (156), inPrt57 (157), inPrt58 (158), inPrt59 (159), inPrt60 (160), inPrt61 (161), inPrt62 (162), inPrt63 (163), inPrt64 (164), inPrt65 (165), inPrt66 (166), inPrt67 (167), inPrt68 (168), inPrt69 (169), inPrt70 (170), inPrt71 (171), inPrt72 (172), inPrt73 (173), inPrt74 (174), inPrt75 (175), inPrt76 (176), inPrt77 (177), inPrt78 (178), inPrt79 (179), inPrt80 (180), inPrt81 (181), inPrt82 (182), inPrt83 (183), inPrt84 (184), notApplicable (255)
I32 prtGenCnfgPortId	1.3.6.1.4.1.164.3.1.4.2.3.1.6	Integer32	read-write	IO Port Id for V5.1 use. This object is applicable only for part of the PSTN and ISDN IO ports. Generally, 0 is a valid value. Nevertheless, for ports that do not support this object, the value will be: notApplicable= 0
I32 prtGenCnfgPrtIdx	1.3.6.1.4.1.164.3.1.4.2.3.1.3	Integer32	read-only	This attribute indicates a unique external or internal port number. For MP: exPrt1 (1) .. exPrt16 (16) , notApplicable(100), inPrt1 (101) .. inPrt84 (184)
I32 prtGenIfIndex	1.3.6.1.4.1.164.3.3.3.1.1.1.4	Integer32	read-only	This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx, the value will be '7fffffff'h.
I32 prtGenPrtIdx	1.3.6.1.4.1.164.3.3.3.1.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtGenTestCmd	1.3.6.1.4.1.164.3.3.3.1.1.1.9	Integer32	read-write	Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMask). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the requested value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system.
I32 prtGenTestDuration	1.3.6.1.4.1.164.3.3.3.1.2.1.3	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to the specified test . The resolution will be a minute, and the maximum duration is limited to 30 minutes . A zero value specifies no time limitation. When the test isn't active the agent initiates this object to 2 min. when the duration is needed and to 0 if it's not required.
I32 prtGenTestMask	1.3.6.1.4.1.164.3.3.3.1.1.1.8	Integer32	read-only	This is a mask which indicates which tests from the 'prtGenTestCmd' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
I32 prtGenTestPrtIdx	1.3.6.1.4.1.164.3.3.3.1.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtGenTestRunning	1.3.6.1.4.1.164.3.3.3.1.1.1.10	Integer32	read-only	This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only!
I32 prtGenTsCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
I32 prtGenTsIConPrt	1.3.6.1.4.1.164.3.3.3.1.3.1.5	Integer32	read-write	This attribute indicates the internally (In Mux) connected port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside ports will be for example, the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * noConnection - will be indicated as 10 for DXC and FCD-E1/T1. - will be indicated as 100 for FCD-E1/I and SMODs. * Split TS (same TS is Split to several ports) - 11. * notApplicable- will be indicated as 100 for LRS IMODs. All HS port's timeslots must have the same destination port.
I32 prtGenTsIConTs	1.3.6.1.4.1.164.3.3.3.1.3.1.6	Integer32	read-write	This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 (or HS) Card. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling. * For DXC: All HS port's timeslots must start with Timeslot no.1
I32 prtGenTsIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.3	Integer32	read-only	This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 or HS Card . In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
I32 prtGenTsPrtIdx	1.3.6.1.4.1.164.3.3.3.1.3.1.2	Integer32	read-only	This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtHdslIdx	1.3.6.1.4.1.164.3.3.3.7.1.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The HDSL ports will be external. For port index, see product specification.
I32 prtHSBertPrtIdx	1.3.6.1.4.1.164.3.3.3.3.2.1.1	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtHSBertTestResult	1.3.6.1.4.1.164.3.3.3.3.2.1.4	Integer32	read-only	This object indicates the number of Bit Error Rate indicated during the BERT test. Active only when bert test is running on the selected port.
I32 prtHSCnfgIdx	1.3.6.1.4.1.164.3.3.3.3.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
I32 prtHsfCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.6.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relate to the TmpCnfg.
I32 prtHSPrtIdx	1.3.6.1.4.1.164.3.3.3.3.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtICnfgIdx	1.3.6.1.4.1.164.3.3.3.6.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
I32 prtIIdx	1.3.6.1.4.1.164.3.3.3.6.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The ISDN B1, B2, D channels will be inside ports. For port index, see product specification.
I32 prtIn1p6VcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.2.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtIn1p6VcPbxPabxTs	1.3.6.1.4.1.164.3.2.3.2.15.2.1.7	Integer32	read-only	This object defines the PABX Time-Slot assigned to this internal port. For a T1 link, the valid values are: 1 .. 24. For an E1 link, the valid values are: 1 .. 31. This object is NOT applicable when prtIn1p6VcPbxConnect=no. This object is applicable for all cards of VC-PBX family. Default=the internal port index (1..6).
I32 prtIn7p8VcPbxCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.15.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtInHsiCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtInHsiConcentratedTo	1.3.6.1.4.1.164.3.2.3.2.8.2.1.6	Integer32	read-write	The Concentration D Channel of the prtInHsiPrtIdx port. The port always belongs to the same card as prtInHsiPrtIdx port. This object is applicable only when prtInHsiRate=concentrated. Valid values: - notApplicable: 255 - for MP-2200: HS-S12, HS-U12 cards: inPrt37 (137) .. inPrt48 (148). HS-S6, HS-U6 cards: inPrt19 (119) .. inPrt24 (124). - for DXC: HS-U8 cards: 112 .. 254 HS-U16 cards: 112 .. 258. See DXC R6 spec for port index convention.
I32 prtInHsiPrtIdx	1.3.6.1.4.1.164.3.2.3.2.8.2.1.3	Integer32	read-only	A unique port identifier within the card. Valid values for MP: inPrt1 (101) .. inPrt48 (148). Valid values for DXC: 11012.. 25316. See DXC R6 spec for port index convention.
I32 prtInLs2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.4.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtInLs2Group	1.3.6.1.4.1.164.3.2.3.2.4.2.1.5	Integer32	read-write	This attribute indicates the group number of the port. LS-2 internal ports with the same group number share the same Time slot of the main link
I32 prtInLs2Member	1.3.6.1.4.1.164.3.2.3.2.4.2.1.6	Integer32	read-write	This attribute indicates the group member id of the port. This parameter is for the automatic envelope assignment algorithm.
I32 prtInLs6CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.13.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtInMbeCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.11.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtInPh1MlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtInPh1MlCongLevel	1.3.6.1.4.1.164.3.2.3.2.2.3.1.9	Integer32	read-write	This attribute indicates the level of delayed data in precents of the total available dynamic memory, for which the port will start to operate . The resolution of the parameter is 5 percent. Valid values: 10..70, 255. 255=notApplicable.
I32 prtInPh1MlDlciCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtInPh1MlDlciIConDlci	1.3.6.1.4.1.164.3.2.3.2.2.4.1.8	Integer32	read-write	This attribute indicates a unique internal connection dlci number which the src dlci is routed to.
I32 prtInPh1MlDlciIdx	1.3.6.1.4.1.164.3.2.3.2.2.4.1.4	Integer32	read-only	This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, then its type is 'user' and the only valid index is 1.
I32 prtInPh1MlDlciPriority	1.3.6.1.4.1.164.3.2.3.2.2.4.1.13	Integer32	read-write	This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority.
I32 prtInPh1MlEnqPeriod	1.3.6.1.4.1.164.3.2.3.2.2.3.1.14	Integer32	read-write	This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlErrorsThreshold	1.3.6.1.4.1.164.3.2.3.2.2.3.1.17	Integer32	read-write	This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlFrWindowSize	1.3.6.1.4.1.164.3.2.3.2.2.3.1.16	Integer32	read-write	This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlFullRptPeriod	1.3.6.1.4.1.164.3.2.3.2.2.3.1.15	Integer32	read-write	This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite (never sent). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
I32 prtInPh1MlMaxIdleTime	1.3.6.1.4.1.164.3.2.3.2.2.3.1.18	Integer32	read-write	Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=Never. Never move to higher prioritized connected link. UNIT is seconds. Valid values are: 0, 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 120, 180, 240, 300, 360, 420, 480, 540, 600, 900, 1200, 1500, 1800. Attempt to Set an invalid value will result in getting the default value.
I32 prtInPh1MlMinSeparators	1.3.6.1.4.1.164.3.2.3.2.2.3.1.22	Integer32	read-write	Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable
I32 prtInPh1MlPrtIdx	1.3.6.1.4.1.164.3.2.3.2.2.3.1.3	Integer32	read-only	This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have three internal interfaces. MX3000 modules may have up to 50 internal ports.
I32 prtInTreCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.12.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtInVc3CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.14.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtIpParamAgingTime	1.3.6.1.4.1.164.6.2.15.6.1.1.19	Integer32	read-write	Aging Time in seconds.
I32 prtIpParamConfigIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.1	Integer32	read-only	This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). For products having Agent and Edit configurations, Write operation for the table entries is allowed only to Config=255.
I32 prtIpParamDefInterface	1.3.6.1.4.1.164.6.2.15.6.1.1.29	Integer32	read-write	The Default Interface for packets with unresolved destination subnet. For internal-X port: 100 + X .
I32 prtIpParamDoubleTagVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.25	Integer32	read-write	VLAN Identifier of the Double Tagging VLAN.
I32 prtIpParamDoubleTagVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.26	Integer32	read-write	VLAN Frame priority of the Double Tagging VLAN.
I32 prtIpParamEncapProtPort	1.3.6.1.4.1.164.6.2.15.6.1.1.21	Integer32	read-write	Encapsulation Protocol Port (TCP/UDP Port).
I32 prtIpParamFloodedRateLimit	1.3.6.1.4.1.164.6.2.15.6.1.1.31	Integer32	read-write	The maximum rate permitted to transfer broadcast, multicast, and unicast flooded frames via this port, in Kbps. 0 - Disable. In Ipmux14 this parameter is applicable when prtIpParamRateLimit=0 (disable).
I32 prtIpParamIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.3	Integer32	read-only	This object indicates a unique Port Index.
I32 prtIpParamKeepAliveInterval	1.3.6.1.4.1.164.6.2.15.6.1.1.34	Integer32	read-write	This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
I32 prtIpParamKeepAliveThresh	1.3.6.1.4.1.164.6.2.15.6.1.1.35	Integer32	read-write	This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
I32 prtIpParamMngVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.10	Integer32	read-write	Management VLAN ID.
I32 prtIpParamMngVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.11	Integer32	read-write	Management VLAN Frame priority.
I32 prtIpParamP2pKeepAliveVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.36	Integer32	read-write	Dedicated VLAN ID for keep alive messages.
I32 prtIpParamP2pKeepAliveVlanPrio	1.3.6.1.4.1.164.6.2.15.6.1.1.37	Integer32	read-write	VLAN priority for P2P keep alive messages .
I32 prtIpParamRateLimit	1.3.6.1.4.1.164.6.2.15.6.1.1.28	Integer32	read-write	The maximum rate permitted to transfer via this port, in Kbps.
I32 prtIpParamSlotIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.2	Integer32	read-only	This object indicates a unique number of the slot position in which the module is inserted. notApplicable = 255 (for products that don't have slots). For KM: kmxMlA (103), kmxMlB (104).
I32 prtIpParamTos	1.3.6.1.4.1.164.6.2.15.6.1.1.17	Integer32	read-write	TOS = Type of Service transmitted. Valid values: 0..255.
I32 prtIpParamVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.23	Integer32	read-write	VLAN Identifier.
I32 prtIpParamVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.24	Integer32	read-write	VLAN Frame priority.
I32 prtIsdnCallBackTimeout	1.3.6.1.4.1.164.3.2.3.2.16.1.1.16	Integer32	read-write	This object is applicable only if 'prtIsdnFilter' is 'CallBack' and determines how long to wait from receiving the incoming call until initiating the call back call. The vaules range should be '1..20 sec' and the default 10 sec.
I32 prtIsdnCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtIsdnDirectoryCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtIsdnDirectoryPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.3.1.3	Integer32	read-only	For MAXcess this is the internal port number: 101, 102,.... For KM-2100 the port index is calculated as follows: 100*Slot+Ch
I32 prtIsdnDirectoryPrtNu	1.3.6.1.4.1.164.3.2.3.2.16.3.1.8	Integer32	read-create	This is the external port number connected to this entry.
I32 prtIsdnDirectoryTeiId	1.3.6.1.4.1.164.3.2.3.2.16.3.1.9	Integer32	read-create	This is the abstract terminal id if relevant, connected to this entry.
I32 prtIsdnEndpointCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtIsdnEndpointPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.2.1.3	Integer32	read-only	This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch
I32 prtIsdnEndpointTeiValue	1.3.6.1.4.1.164.3.2.3.2.16.2.1.6	Integer32	read-create	When the TEI Type is static, the value of the TEI should be between 0 and 63. Else, it is not selectable by user. 255 = notApplicable. It corresponds to isdnEndpointTeiValue in the isdn MIB
I32 prtIsdnNumOfAbstractTerm	1.3.6.1.4.1.164.3.2.3.2.16.1.1.10	Integer32	read-write	An object for KM2100/4 agents. 255=Not Applicable When ISDN Standard = ETSI or NTT (European) the value should be 255 (NotApplicable) else If ML speed is 64Kbps value should be 1. If ML speed is 128Kbps value can be either 1 or 2 (user selection).
I32 prtIsdnPrtIdx	1.3.6.1.4.1.164.3.2.3.2.16.1.1.3	Integer32	read-only	This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch
I32 prtLanWanCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
I32 prtLanWanDestIf	1.3.6.1.4.1.164.3.2.3.2.22.1.1.5	Integer32	read-write	This object determines the Destination Interface for the frames received by this port. - Switching Table = 100 (it means that the destination interface will be determined by the Switching Table) - inPrtX (internal-X port): 100 + X . For FCD-155 this object is not applicable =0
I32 prtLanWanMtu	1.3.6.1.4.1.164.3.2.3.2.22.1.1.13	Integer32	read-write	The size of the largest packet which can be sent/received on the interface, specified in octets. Valid values change per device. 0=not applicable.
I32 prtLanWanPrtIdx	1.3.6.1.4.1.164.3.2.3.2.22.1.1.3	Integer32	not-accessible	This object indicates a unique number to identify a port in a specific card. Generally, for MP-210X/2200, the Port Index will be according to the external/internal port number: - exPrtX : X - inPrtX : 100 + X For FCD-155, refer to device specification
I32 prtLanWanStpCost	1.3.6.1.4.1.164.3.2.3.2.22.1.1.9	Integer32	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
I32 prtLanWanStpPriority	1.3.6.1.4.1.164.3.2.3.2.22.1.1.8	Integer32	read-write	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID.
I32 prtLanWanVlanId	1.3.6.1.4.1.164.3.2.3.2.22.1.1.11	Integer32	read-write	This is the VLAN Id attached to a frame, when the relevant Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is tag or doubleTag. 0=not applicable.
I32 prtLanWanVlanPriority	1.3.6.1.4.1.164.3.2.3.2.22.1.1.12	Integer32	read-write	This is the VLAN Priority attached to a frame, when the relevant Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is tag or doubleTag. Valid values: 0..7 255=not applicable.
I32 prtLogicalCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtLogicalPrtIdx	1.3.6.1.4.1.164.3.2.3.2.17.1.1.3	Integer32	read-only	This attribute indicates a unique port number. This port number should be an internal port number: inPrt1(101)->inPrt50(150), linkSel1(200)->linkSel50(250), encaps1(300)-> encaps50(350), huntGr1(101) -> huntGr10(110).
I32 prtMl4CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.19.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
I32 prtMl4DedicatedTs	1.3.6.1.4.1.164.3.2.3.2.19.1.1.18	Integer32	read-write	A unique number to identify Dedicated TS of the E1 port (V5.2). It is applicable only when prtMl4Service=v52Slave and prtExPh1MlInbandMng selected is dedicatedTs, dedicatedPpp or dedicatedFr. 1..31 - Dedicated TS of E1 255 - notApplicable Other values are invalid.
I32 prtMl4LogicalLinkId	1.3.6.1.4.1.164.3.2.3.2.19.1.1.17	Integer32	read-write	This object defines for a V5.2 Master ML the Logical Link Id. Valid values are: 0..256. NA=257.
I32 prtMl4OosEntryThreshold	1.3.6.1.4.1.164.3.2.3.2.19.1.1.15	Integer32	read-write	This object defines the number of Errors per Second that determine the minimum unacceptable noise level. This value will be the Entry Threshold to the OOS (Out-of-Service) state. This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable.
I32 prtMl4OosExitThreshold	1.3.6.1.4.1.164.3.2.3.2.19.1.1.16	Integer32	read-write	This object defines the number of consecutive Error-Free-Seconds before going from OOS state to Normal state. This value will be the Exit Threshold from the OOS (Out-of-Service) state. Units=seconds This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable.
I32 prtMonCnfgIdx	1.3.6.1.4.1.164.3.3.3.1.6.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. For products that do not support configurations, 1 will be always used.
I32 prtMonitoredPort	1.3.6.1.4.1.164.3.3.3.1.6.1.5	Integer32	read-write	This object indicates the MONITORED Port Index that the Monitoring port monitors. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * 100 - no port monitored For Optimux-T3: The valid channels are: 0 = no Ch monitored 1..21 or 1..28 (=CH1..CH21 or CH1..CH28) according to product's configuration.
I32 prtMonitoringIdx	1.3.6.1.4.1.164.3.3.3.1.6.1.2	Integer32	read-only	This object indicates the Monitoring Port Index. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Optimux-T3: 255 (Not Applicable) will be always used. The Monitoring port is always the Station Clock (not considered an interface).
I32 prtParamIdx	1.3.6.1.4.1.164.6.2.15.5.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. For ACE2002: This parameter is the physical layer ifIndex of the slot on which the NMS requires the next interface index.
I32 prtParamSignalLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.17	Integer32	read-only	This object indicates signal level (in thenth of dB units) on selected port.
I32 prtPerfBBE	1.3.6.1.4.1.164.6.2.15.3.1.1.7	Integer32	read-only	Number of Background Block (or Frame) Errors for the reference period (prtPerfPeriodRef).
I32 prtPerfBlocksPerSec	1.3.6.1.4.1.164.6.2.15.3.1.1.8	Integer32	read-only	Blocks per second (or frames per second) of the port/interface indicated by portIdx. This object is constant for a certain port/interface. It is not affected by the prtPerfPeriodRef index.
I32 prtPerfElapsedTime	1.3.6.1.4.1.164.6.2.15.3.1.1.3	Integer32	read-only	Elapsed Time in seconds. - for prtPerfPeriodRef=currentPeriod: The period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. - for prtPerfPeriodRef=lastPeriod: The value of prtPerfElapsedTime when last prtPerfSaveAndResetCmd was received.
I32 prtPerfES	1.3.6.1.4.1.164.6.2.15.3.1.1.5	Integer32	read-only	Number of Errored Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfIdx	1.3.6.1.4.1.164.6.2.15.3.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
I32 prtPerfSES	1.3.6.1.4.1.164.6.2.15.3.1.1.6	Integer32	read-only	Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfUAS	1.3.6.1.4.1.164.6.2.15.3.1.1.4	Integer32	read-only	Number of Unavailable Seconds for the reference period (prtPerfPeriodRef).
I32 prtPhMlCnfgIdx	1.3.6.1.4.1.164.3.2.3.2.2.5.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
I32 prtPhMlSyncRestore	1.3.6.1.4.1.164.3.2.3.2.2.5.1.10	Integer32	read-write	Sync Restoration time, in seconds. notApplicable=0.
I32 prtPhyIntervalNumber	1.3.6.1.4.1.164.3.1.6.8.2.2.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
I32 prtPhyTimeElapsed	1.3.6.1.4.1.164.3.1.6.8.1.2.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period.
I32 prtPhyValidIntervals	1.3.6.1.4.1.164.3.1.6.8.1.2.1.2	Integer32	read-only	The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute since the interface has been online.
I32 prtPriorityIdx	1.3.6.1.4.1.164.6.3.4.1.1.3	Integer32	not-accessible	This object indicates the Traffic Priority Index.
I32 prtPriorityIdx1	1.3.6.1.4.1.164.6.3.4.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. or any other Index.
I32 prtPriorityIngressRateLimit	1.3.6.1.4.1.164.6.3.4.1.1.4	Integer32	read-write	The maximum rate permitted at Ingress of this port with this Traffic Priority, in Kbps.
I32 prtPriorityPrtIdx	1.3.6.1.4.1.164.6.3.4.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
I32 prtSAlarmCode	1.3.6.1.4.1.164.3.3.3.1.4.1.1.3	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
I32 prtSAlarmCounter	1.3.6.1.4.1.164.3.3.3.1.4.1.1.8	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
I32 prtSAlarmIdx	1.3.6.1.4.1.164.3.3.3.1.4.1.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive.
I32 prtSAlarmPrtIdx	1.3.6.1.4.1.164.3.3.3.1.4.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
I32 prtSAlrCode	1.3.6.1.4.1.164.3.1.4.1.2.1.5	Integer32	read-only	A code identifying the alarm of an entry in the alarm status table at port level.
I32 prtSAlrCounter	1.3.6.1.4.1.164.3.1.4.1.2.1.8	Integer32	read-only	A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
I32 prtSAlrIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.1	Integer32	read-only	A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive
I32 prtSAlrPrtIdx	1.3.6.1.4.1.164.3.1.4.1.2.1.3	Integer32	read-only	This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a port which does not exist. Valid valuesfor MP-2100/2200: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148), IP Bundles. For other products, see product's spec.
I32 prtSBertTstRslt	1.3.6.1.4.1.164.3.1.4.1.1.1.13	Integer32	read-only	This attribute indicates the number of Bit Error Rate indicated during the BERT operation. It is valid only when bert test is active on the specific port.
I32 prtSInstIfIndex	1.3.6.1.4.1.164.3.1.4.1.1.1.4	Integer32	read-only	This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx the value will be '7fffffff'h.
I32 prtSInstPrtIdx	1.3.6.1.4.1.164.3.1.4.1.1.1.2	Integer32	read-only	This attribute indicates a unique number to identify a port in a specific card. The valid ports depend on the installed card: the valid external ports (interfaces) are (1..mdlCNoOfExternPrt) if any, and the valid internal ports are (101..100+mdlCNoOfInternPrt) if any. Generally, for MP-2100/2200: exPrt1 (1) .. exPrt16 (16),inPrt1(101) .. inPrt48 (148) For the Vmux-2100 device: This index will have values of 1...4 for the physical ports & values of ifIndex for the bundles. For other products, see product's spec.
I32 prtSpCnfgIdx	1.3.6.1.4.1.164.3.3.3.4.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
I32 prtSpNoOfRetries	1.3.6.1.4.1.164.3.3.3.4.1.1.12	Integer32	read-write	For DXC - this object is applicable only for port (2) = DP. The number of dialing retries requested. Default = 0
I32 prtSpPrtIdx	1.3.6.1.4.1.164.3.3.3.4.1.1.2	Integer32	read-only	This attribute indicates a unique port number of the SPor DP port. For DXC, it is the port in the active DCL card: - SP = 1 - NP ; DP = 2 For Kilomux, the port index is calculated as follows: 100*Slot+Ch. For FCD, PRBi, the SP port index=1. For Optimux-T3, the SP port index=71.
I32 prtSTestMask	1.3.6.1.4.1.164.3.1.4.1.1.1.9	Integer32	read-only	This is a mask which indicates which tests from the 'prtSTstCmd' list are allowed for the requested port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
I32 prtSTstDuration	1.3.6.1.4.1.164.3.1.4.1.1.1.11	Integer32	read-write	This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to all the test operations. The resolution will be a minute, and the maximum duration is limited to 30 minutes. For Vmux devices, the values are in seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtSTstCmd' parameter.
I32 prtSupervisoryIndex	1.3.6.1.4.1.164.6.2.15.2.1.1.1	Integer32	read-only	The SP port index. For some products, having modules (cards): The LS byte of the integer is the port index 1..255. The MS byte is different than 0 only if the port belongs to a module. In that case it is the module number. For other products' index see their specification.
I32 prtT1E1CnfgIdx	1.3.6.1.4.1.164.3.3.3.2.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
I32 prtT1E1DedicatedTs	1.3.6.1.4.1.164.3.3.3.2.2.1.19	Integer32	read-write	The value is differently determined for different products. There are two methods: 1) A unique number to identify Dedicated TS of the T1/E1 port. It is applicable only when prtExT1E1InbandMng selected is dedicatedTs. 1..24 - Dedicated TS of T1 1..31 - Dedicated TS of E1 255 - notApplicable (for agents that do not support this feature) Other values are invalid. 2) For FCD-STM, up to five TSs may be dedicated to management. This object value is the Sum (sigma) of 2n, where n =TS-1 e.g. Time slots 3,5,7,9,11 are dedicated to management: 2 2 +2 4 +2 6 +2 8 +210 = 4+16+64+256+1024=1364 User should consult the product specification, to find out the method employed.
I32 prtT1E1FdlMsgPrtIdx	1.3.6.1.4.1.164.3.3.3.2.3.1.1	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 .
I32 prtT1E1MaxTSs	1.3.6.1.4.1.164.3.3.3.2.2.1.31	Integer32	read-write	This object is applicable only for DXC D4T1, D4E1, D8T1, D8E1 external ports and D8GSL internal E1 ports. It is relevant only when sysCIntTsAllocMode=static(2). 255=not applicable If prtT1E1LineType=unframed(8), the value of this object must be 32. Else, the valid values are 0..31.
I32 prtT1E1PrtIdx	1.3.6.1.4.1.164.3.3.3.2.2.1.2	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20.
I32 prtT1E1SPrtIdx	1.3.6.1.4.1.164.3.3.3.2.1.1.1	Integer32	read-only	This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 .
I32 prtT3E3CnfgIdx	1.3.6.1.4.1.164.3.3.3.8.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For DXC, write operations can be performed only on the Temp Config. For products that do not support configurations, always 1 will be used.
I32 prtT3E3PrtIdx	1.3.6.1.4.1.164.3.3.3.8.1.1.2	Integer32	read-only	This attribute indicates a unique port number. For DXC: The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The external ports convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For Optimux-T3: Link-A: 51 Link-B: 61 .
I32 prtTestCmdAndStatus	1.3.6.1.4.1.164.6.2.15.4.1.1.2	Integer32	read-write	Setting this object to a value as detailed further on (except 0) will initiate a test on the specific port. The test/s requested will be set according to the respective bit. The value of this object will be a sum of (2**n), where n is the Bit: TEST BIT VALUE ----------- --- ------ reserved 0 1 PayloadLoop=RLB 1 (=Remote Loopback) 2 LineLoop=DIG 2 (=Digital) 4 OtherLoop 3 8 InwardLoop=LLB 4 (=Local Loopback) 16 BERT 5 32 LC 6 64 ToneInjection 7 128 Inband 8 256 BERT Remote (or E1/T1 RLB) 9 512 Downstream-AIS (or E1/T1 LLB) 10 1024 Upstream-AIS 11 2048 Rem-Loop-on-Rem-Unit 12 4096 MacSwapLoop 13 8192 OamETHLoopback 14 16384 OamETHLinkTrace 15 32768 e.g : If the requested value is 20 -> 010100 -> Bits 2 & 4 are set -> the requested tests are : LineLoopback=DIG InwardLoopback=LLB Not all tests combinations are valid. For valid test combination, see each product's specification. For LRS52, only single test is allowed simultaneously The terminology and order of the first tests (except BERT) is according to the one used for Test Status of DS1 and DS3 standards. The notations : RLB, LLB, DIG are the most used in RAD's products, but they can be different. For exact definition see product's spec. Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port. When no test is running on the port, the Get value (test status) will be 0. PayloadLoop=RLB The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. LineLoop=DIG The received signal at this interface does not go through the device (minimum penetration) but is looped back out. OtherLoop Loopbacks that are not defined here. InwardLoop=LLB The sent signal at this interface is looped back through the device. LC This loop is applicable only for HSSI interface, towards the router . ToneInjection This loop is applicable for analog voice (like FXS). Downstream-AIS E1 AIS signal (all ones) is transmitted in the relevant channel toward the STM-1 line. Upstream-AIS E1 AIS signal (all ones) is generated in the relevant channel toward the local received tributary channel output Rem-Loop-on-Rem-Unit Request from far end device to activate remote loopback towards near-end device MacSwapLoop This loop is applicable for ethernet port. Loop is implemented by swapping the MAC addresses of the incoming message. OamETHLoopback Ethernet Loopback is used to verify connectivity of a MEP with a MIP or peer MEP(s) (ITU-T Y.1731, Clause 7.2). OamETHLinkTrace Ethernet Link Trace is an on-demand OAM function which can be used for the two following purposes: - Adjacent Relation Retrieval - Fault Localization (ITU-T Y.1731, Clause 7.3).
I32 prtTestIdx	1.3.6.1.4.1.164.6.2.15.4.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
I32 prtTestMacSwapLoopVlanId	1.3.6.1.4.1.164.6.2.15.4.1.1.15	Integer32	read-write	This object specifies the VLAN ID for prtTestMacSwapLoopDataMode=specificVlan.
I32 prtTestTimeout	1.3.6.1.4.1.164.6.2.15.4.1.1.5	Integer32	read-write	This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. For RICi-E1T1, RICi-E3T3 the measurement unit is in seconds. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever
I32 prtTestVctRxCrossPair	1.3.6.1.4.1.164.6.2.15.4.1.1.11	Integer32	read-only	This object should be equal to the Index (prtTestIdx) of the Rx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair. This object was especially created for ETX-202. Currently not in use.
I32 prtTestVctRxDistance	1.3.6.1.4.1.164.6.2.15.4.1.1.8	Integer32	read-only	This object indicates the distance in Meters to the RX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
I32 prtTestVctTxCrossPair	1.3.6.1.4.1.164.6.2.15.4.1.1.12	Integer32	read-only	This object should be equal to the Index (prtTestIdx) of the Tx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.
I32 prtTestVctTxDistance	1.3.6.1.4.1.164.6.2.15.4.1.1.9	Integer32	read-only	This object indicates the distance in Meters to the TX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
I32 prtVc2CnfgIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
I32 prtVc2PrtIdx	1.3.6.1.4.1.164.3.2.3.2.5.1.3	Integer32	read-only	A unique identifier of the port, within the card. For MP-2100/2200 card ports, Web Ranger and FCD-IP Voice ports the values will be: exPrt1 (1) exPrt2 (2) exPrt3 (3) exPrt4 (4) exPrt5 (5) exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) exPrt10 (10) exPrt11 (11) exPrt12 (12) exPrt13 (13) exPrt14 (14) exPrt15 (15) exPrt16 (16) For LA-240: The index for fixed voice ports will be - exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) The index for voice card ports will be - Slot number * 100 + ch (for IO-1: 101..104, for IO-2: 201..204). For other products' index see their specification.
I32 radBridgeCODCondIfIndex	1.3.6.1.4.1.164.4.1.4.4.1.1	Integer32	read-only	The interface, this COD entry is applicable to.
I32 radBridgeCODConnectDelay	1.3.6.1.4.1.164.4.1.4.1.1.4	Integer32	read-write	The connect delay defines the minimum time period that the link must stay disconnected, between 2 succesive connections (in seconds).
I32 radBridgeCODDisConnectMinimunFramesNumber	1.3.6.1.4.1.164.4.1.4.4.1.7	Integer32	read-write	Frames rate.
I32 radBridgeCODIfIndex	1.3.6.1.4.1.164.4.1.4.1.1.1	Integer32	read-only	The interface to which this COD entry is applicable.
I32 radBridgeCODisConnectDelay	1.3.6.1.4.1.164.4.1.4.1.1.5	Integer32	read-write	The disconnect delay defines the minimum time period the link must stay connected, between 2 succesive disconnections (in seconds).
I32 radBridgeCODOriginateDisConnectDelay	1.3.6.1.4.1.164.4.1.4.4.1.4	Integer32	read-write	Delay time in seconds.
I32 radBridgeCODTimeIfIndex	1.3.6.1.4.1.164.4.1.4.2.1.1	Integer32	read-only	The interface to which this COD Time Trigger entry is applicable.
I32 radBridgeCODTimeTriggerNum	1.3.6.1.4.1.164.4.1.4.2.1.3	Integer32	read-only	Every day of the week the user can configure 3 dial up connections.
I32 radBridgeCODTotalConnecTime	1.3.6.1.4.1.164.4.1.4.1.1.8	Integer32	read-only	The sum of all the connect time intervals since the COD was reset.
I32 radBridgeCurrentIndex	1.3.6.1.4.1.164.4.1.7.1.1.1	Integer32	read-only	The index of the Bridge interface or Bridge Port. It may be ifIndex.
I32 radBridgeGenCfgIdx	1.3.6.1.4.1.164.4.1.9.4.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg. For Agents that support only one Configuration, this object will be constant=1.
I32 radBridgeGenCfgIdx2	1.3.6.1.4.1.164.4.1.9.4.1.2	Integer32	not-accessible	For Agents having more than one bridge, this index may be used as bridge index
I32 radBridgeGenFlowBroadcastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.9	Integer32	read-create	The Traffic Class the received Broadcast frame is mapped to.
I32 radBridgeGenFlowCnfgIdx	1.3.6.1.4.1.164.4.1.9.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.
I32 radBridgeGenFlowFloodOrBcastMaxRate	1.3.6.1.4.1.164.4.1.9.1.1.4	Integer32	read-create	This object controls maximum Flooding or Broadcast Rate: Max number of multicast along with unknown or flooded unicast frames allowed to enter any port. The number can be presented either as percentage of bandwidth, or bandwidth in Kbps. Once the limit is exceeded, any multicast or flooded frame entering from the port is discarded For RIC-155, and FCD-155 valid values are 3% , 6%, 12% and 100% = No Limit
I32 radBridgeGenFlowIdx	1.3.6.1.4.1.164.4.1.9.1.1.2	Integer32	not-accessible	For Agent having more than one bridge, this index may be used as bridge index
I32 radBridgeGenFlowMulticastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.8	Integer32	read-create	The Traffic Class the received Multicast frame is mapped to.
I32 radBridgeGenFlowUnkownUnicastTrafficClass	1.3.6.1.4.1.164.4.1.9.1.1.10	Integer32	read-create	The Traffic Class the received Unkonwn Unicast frame is mapped to.
I32 radBridgeInactiveArpTimeOut	1.3.6.1.4.1.164.4.1.2	Integer32	read-write	This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
I32 radBridgeIntervalIndex	1.3.6.1.4.1.164.4.1.7.2.1.1	Integer32	read-only	The index of the bridge interface or Bridge Port. It may be ifIndex.
I32 radBridgeIntervalNumber	1.3.6.1.4.1.164.4.1.7.2.1.2	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
I32 radBridgeInvBasePort	1.3.6.1.4.1.164.4.1.10.1.1.2	Integer32	read-only	The Bridge port number.
I32 radBridgeInvBasePortIfIndex	1.3.6.1.4.1.164.4.1.10.1.1.1	Integer32	read-only	The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this Bridge port.
I32 radBridgeIPXRipHopMetric	1.3.6.1.4.1.164.4.1.5.2.6.1.6	Integer32	read-write	The metric, in terms of distance , associated with the route given by the entry.
I32 radBridgeIPXRipInfAgeMultiplier	1.3.6.1.4.1.164.4.1.5.2.7.1.3	Integer32	read-write	The holding multiplier for information received in RIP periodic updates. Zero value corresponds to infinite aging time.
I32 radBridgeIPXRipInfBcastUpdate	1.3.6.1.4.1.164.4.1.5.2.7.1.2	Integer32	read-write	The RIP periodic update interval, in seconds. Zero value corresponds to infinite interval.
I32 radBridgeIPXRipInfIfIndex	1.3.6.1.4.1.164.4.1.5.2.7.1.1	Integer32	read-only	This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.
I32 radBridgeIPXRipNIC	1.3.6.1.4.1.164.4.1.5.2.6.1.4	Integer32	read-write	An interface identifier specifying what IPX interface the next hop can be found on.
I32 radBridgeIPXRipTblBcastTrigUpdateInterval	1.3.6.1.4.1.164.4.1.5.2.5	Integer32	read-write	The default time interval (in seconds)between triggered RIP updates on a broadcast type interface. A triggered update occurs when a change is detected in the routing database. This time interval delays the broadcasting of these updates so that changes on the network will not result in a lot of triggered updates.
I32 radBridgeIPXRipTblNoOfEntries	1.3.6.1.4.1.164.4.1.5.2.4	Integer32	read-only	The max number of entries that exist in the RIP routing table.
I32 radBridgeIPXRipTickMetric	1.3.6.1.4.1.164.4.1.5.2.6.1.5	Integer32	read-write	The metric, in terms of transit time, associated with the route given by the entry. This time is in terms of 1/18ths of a second.
I32 radBridgeIPXSapHopsToServer	1.3.6.1.4.1.164.4.1.5.3.6.1.6	Integer32	read-write	The number of hops to the entity on which this server exists.
I32 radBridgeIPXSapInfAgeMultiplier	1.3.6.1.4.1.164.4.1.5.3.7.1.3	Integer32	read-write	The holding multiplier for information received in SAP periodic updates. Zero value corresponds to infinite aging time.
I32 radBridgeIPXSapInfBcastUpdate	1.3.6.1.4.1.164.4.1.5.3.7.1.2	Integer32	read-write	The SAP periodic update interval, in seconds. Zero value corresponds to infinite interval.
I32 radBridgeIPXSapInfIfIndex	1.3.6.1.4.1.164.4.1.5.3.7.1.1	Integer32	read-only	This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.
I32 radBridgeIPXSapNIC	1.3.6.1.4.1.164.4.1.5.3.6.1.7	Integer32	read-write	An Network Interface Card identifier specifying what IPX interface the next hop can be found on.
I32 radBridgeIPXSapServerType	1.3.6.1.4.1.164.4.1.5.3.6.1.1	Integer32	read-only	The type of the server for which this entry pertains.
I32 radBridgeIPXSapSocket	1.3.6.1.4.1.164.4.1.5.3.6.1.5	Integer32	read-write	The IPX socket number that is being used by the server to which this entry pertains.
I32 radBridgeIPXSapTblBcastTrigUpdateInterval	1.3.6.1.4.1.164.4.1.5.3.5	Integer32	read-write	The default time interval (in seconds) between triggered SAP updates on a broadcast style interface. A triggered update occurs when a change is detected in the service database. This time interval delays the transmission of these updates so that changes on the network will not result in a lot of triggered updates.
I32 radBridgeIPXSapTblNoOfEntries	1.3.6.1.4.1.164.4.1.5.3.4	Integer32	read-only	The max number of entries that exist in the SAP Server Information table.
I32 radBridgeMaskIfIndex	1.3.6.1.4.1.164.4.1.3.1.2	Integer32	read-only	Specifies the if Index of the interface to which the mask is applied.
I32 radBridgeMaskNum	1.3.6.1.4.1.164.4.1.3.1.3	Integer32	read-only	The Mask entry number, defined by its line number in the mask table.
I32 radBridgeMaskOffset1	1.3.6.1.4.1.164.4.1.3.1.8	Integer32	read-write	Specifies the radBridgeMaskPat1 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm1.The mask offset is an even decimal number in the range of 0 to 1518.
I32 radBridgeMaskOffset2	1.3.6.1.4.1.164.4.1.3.1.13	Integer32	read-write	Specifies the radBridgeMaskPat2 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm2.The mask offset is an even decimal number in the range of 0 to 1518.
I32 radBridgeMaskOffset3	1.3.6.1.4.1.164.4.1.3.1.18	Integer32	read-write	Specifies the radBridgeMaskPat3 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm3. The mask offset is an even decimal number in the range of 0 to 1518.
I32 radBridgePortBaseVlanCnfgIdx	1.3.6.1.4.1.164.4.1.8.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
I32 radBridgePortBaseVlanIdx	1.3.6.1.4.1.164.4.1.8.1.1.2	Integer32	not-accessible	Index of the port based VLAN.
I32 radBridgePortCnfgDefaultVci	1.3.6.1.4.1.164.4.1.13.1.1.7	Integer32	read-write	This object indicates the VCI of this Bridge Port's Default VCL. An incoming frame with priority that is not assigned to any VCL will be transferred to the Default VCL.
I32 radBridgePortCnfgDefaultVpi	1.3.6.1.4.1.164.4.1.13.1.1.6	Integer32	read-write	This object indicates the VPI of this Bridge Port's Default VCL. An incoming frame with priority that is not assigned to any VCL will be transferred to the Default VCL.
I32 radBridgePortCnfgEgressMtu	1.3.6.1.4.1.164.4.1.13.1.1.10	Integer32	read-write	The size of the largest packet which can be sent on the interface, specified in octets.
I32 radBridgePortCnfgIdx	1.3.6.1.4.1.164.4.1.13.1.1.1	Integer32	not-accessible	The first index of the table. It can serve for Configuration index, Bridge index or other.
I32 radBridgePortCnfgIngressMtu	1.3.6.1.4.1.164.4.1.13.1.1.9	Integer32	read-write	The size of the largest packet which can be received on the interface, specified in octets.
I32 radBridgePortCnfgMaxMacAddr	1.3.6.1.4.1.164.4.1.13.1.1.3	Integer32	read-write	This object indicates the maximum number of total MAC Addresses (static and learned) supported by this Bridge Port.
I32 radBridgePortCnfgPrtIdx	1.3.6.1.4.1.164.4.1.13.1.1.2	Integer32	not-accessible	This object indicates the Bridge Port index.
I32 radBridgePortCnfgStatVlanId	1.3.6.1.4.1.164.4.1.13.1.1.8	Integer32	read-write	This object indicates the selected VlanId of the bridge port on which statistics are being collected. 0=no Statistics collected for VLAN on this bridge port.
I32 radBridgePortVlanMemberBridgeIdx	1.3.6.1.4.1.164.4.1.8.2.1.1	Integer32	read-only	This object indicates the Bridge Index.
I32 radBridgePortVlanMemberPortIdx	1.3.6.1.4.1.164.4.1.8.2.1.2	Integer32	read-only	This object indicates the Bridge's Port Index. For some cases, it can be used as the Port ofIndex.
I32 radBridgePortVlanMemberVlanId	1.3.6.1.4.1.164.4.1.8.2.1.3	Integer32	read-only	This object indicates the VLAN ID.
I32 radBridgeStpCnfgIdx1	1.3.6.1.4.1.164.4.1.11.1.1.1	Integer32	not-accessible	This object indicates the Index of the Agent Configuration the following objects refer to. For Agents that support more than one configuration: 255=Temporary Cnfg ; Set can be done only to this configuration. For Agents that support only one configuration, this object will be constant=1.
I32 radBridgeStpCnfgIdx2	1.3.6.1.4.1.164.4.1.11.1.1.2	Integer32	not-accessible	For Agents having the table objects per Card/Bridge/Interface this will be the index of the Card/Bridge/Interface used.
I32 radBridgeStpCnfgPriority	1.3.6.1.4.1.164.4.1.11.1.1.6	Integer32	read-write	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID, per radBridgeStpCnfgIdx2 instance.
I32 radBridgeStpStatIdx	1.3.6.1.4.1.164.4.1.11.2.1.1	Integer32	not-accessible	For Agents having the table objects per Card/Bridge/Interface this will be the index of the Card/Bridge/Interface used.
I32 radBridgeStpStatRootCost	1.3.6.1.4.1.164.4.1.11.2.1.6	Integer32	read-only	The cost of the path to the root as seen from this bridge.
I32 radDot1qPortDefaultVlanPriority	1.3.6.1.4.1.164.4.1.9.3.1.3	Integer32	read-write	Default VLAN Frame priority of the VLAN added by this port.
I32 radMepTransmitLbmMassages	1.3.6.1.4.1.164.3.1.6.1.3.1.1.23	Integer32	read-create	The number of Loopback messages to be transmitted.
I32 ripSapIfConfIfIndex	1.3.6.1.4.1.164.11.7.2.3.4.1.1	Integer32	read-only	The interface ifIndex.
I32 rowInfoCounter	1.3.6.1.4.1.164.6.2.43.1.2	Integer32	read-only	The Number of rows in the table, indicated by rowInfoTableId.
I32 rowInfoIndexNext	1.3.6.1.4.1.164.6.2.43.1.3	Integer32	read-only	The First Free Index of the table, indicated by rowInfoTableId.
I32 rowInfoMaxNoOfRows	1.3.6.1.4.1.164.6.2.43.1.4	Integer32	read-only	The maximum possible number of rows in the table, indicated by rowInfoTableId.
I32 schedParam	1.3.6.1.4.1.164.6.2.14.5.1.3	Integer32	read-create	A Parameter that might be used whenever the scheduled action takes place. For summer-time schedule - This variable represents the time offset (in minutes), meaning: the number of minutes that should be added for summer-time.
I32 swdlStatusIdx	1.3.6.1.4.1.164.6.2.12.11.1.2	Integer32	read-only	The index of the status rows.
I32 swdlStatusStatus	1.3.6.1.4.1.164.6.2.12.11.1.6	Integer32	read-only	The status of the down load process. Value: Fail (2), OK (3), InProcess (4).
I32 swdlStatusTypeIdx	1.3.6.1.4.1.164.6.2.12.11.1.1	Integer32	read-only	The index of the down-load type (e.g. external (1) or internal (2)).
I32 sysBufferAlrCode	1.3.6.1.4.1.164.3.3.1.5.1.1.2	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and thir related descriptions will be known by the NMS (for display purpose) and will appear in the unit's user manual.
I32 sysBufferAlrIdx	1.3.6.1.4.1.164.3.3.1.5.1.1.1	Integer32	read-only	An index number of the current alarms.
I32 sysBufferAlrPort	1.3.6.1.4.1.164.3.3.1.5.1.1.5	Integer32	read-only	The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999.
I32 sysCClkCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. It can be also a combination of the configuration number and the Card/Port/Other System index.
I32 sysCClkRevertiveTimeout	1.3.6.1.4.1.164.3.3.1.6.1.1.6	Integer32	read-write	The time in seconds in which the system will monitor the higher level clock source, before decision to revert to that clock. In case the time is zero, revertive mode will be disabled.
I32 sysCClkSrcPrt	1.3.6.1.4.1.164.3.3.1.6.1.1.4	Integer32	read-write	This entry is valid only when working in rxClk mode (for IPmux1000 this entry will be valid whe working in LBT mode). For ACE2002 in case of invalid entry the return value will be 0. For other products in case of invalid entry the return value will be 9999. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The SP ports will be numbered as follows: - SP port 1 : 1 - SP port 2 : 2 For external ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Kmux, the port will be according to : Slot*100+Ch. For ACE2002, LA140 and IPmux1000 (GMUX), the port will be ifIndex.
I32 sysCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.2.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. For Gmux2000 the range limitation (1..255) was discarded since the Idx is computed as: x 1000 + 255.
I32 sysCRdnBufferErrorsThreshold	1.3.6.1.4.1.164.3.3.1.6.3.1.17	Integer32	read-create	This parameter determines the number of Buffer undeflow/ overflow events occured in the time window that cause switching.
I32 sysCRdnBuffUnderrunTime	1.3.6.1.4.1.164.3.3.1.6.3.1.18	Integer32	read-create	This parameter determines how much time to wait before switching, after jitter buffer underrun. Switching occurs if no frame arrives within that time. For Ipmux time is counted in msec.
I32 sysCRdnCnfgIdx	1.3.6.1.4.1.164.3.3.1.6.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
I32 sysCRdnEventsTimeWindow	1.3.6.1.4.1.164.3.3.1.6.3.1.15	Integer32	read-create	This parameter determines the time window in which to count events to trigger protection switching. For Ipmux time is counted in seconds.
I32 sysCRdnFlipUponEvent	1.3.6.1.4.1.164.3.3.1.6.3.1.13	Integer32	read-create	This object allows user to define if Flip to the other port will be performed (or not), for certain possible events. Each event is represented by a bit. The value of the object is a sum of 2**n, according to the bits having '1' value. '1' - means that Flip should occur due to this event. Bit 0 (LSB) = SD (Signal Degraded). For IPmux: Bit 0 (LSB) = TDM Line LOS/LOF. Bit 1 = Sequence Number. Bit 2 = Jitter Buffer errors.
I32 sysCRdnLosOrLofTime	1.3.6.1.4.1.164.3.3.1.6.3.1.14	Integer32	read-create	This parameter determines how much time to wait before switching, after LOF or LOS are detected on the TDM Line. For Ipmux time is counted in msec.
I32 sysCRdnPrimePort	1.3.6.1.4.1.164.3.3.1.6.3.1.3	Integer32	read-only	The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For an IP Bundle that is in an External Device (not in this MP), the value will be: 70,000 + ifIndex of Secondary Bundle. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level).
I32 sysCRdnRecTime	1.3.6.1.4.1.164.3.3.1.6.3.1.8	Integer32	read-create	Redundancy Recovery Time (sec). After switching to the current online card, the next switch can be performed only after a minimum time, indicated by this object. Valid Values: 0..300, 65535. 65535=NA. This object is applicable only when sysCRdnRecMode=auto.
I32 sysCRdnSecPort	1.3.6.1.4.1.164.3.3.1.6.3.1.5	Integer32	read-create	The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For an IP Bundle that is in an External Device (not in this MP), the value will be: 0. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level).
I32 sysCRdnSequenceNumberThreshold	1.3.6.1.4.1.164.3.3.1.6.3.1.16	Integer32	read-create	This parameter determines the number of Sequence Number errors that should occur in the time window in order to cause switching.
I32 sysCSs7FisuSuppression	1.3.6.1.4.1.164.3.3.1.6.2.1.9	Integer32	read-write	SS7 Suppresion is used for SS7 Spoofing. The SS7 spoofing terminates the keep alive messages from the local VMUX without sending them over the network, thus improving the bandwidth utilization. FISU means Fill in Service Unit - Keep alive that is sent when no one is talking on the line. This object enables the configuration of the SS7 Keep Alive packet % that will be discarded. Legal Values: 0 - No Suppression, 10%, 20%, 30% .. 90% Example: For a value of 10, 1 keep alive packet will be discarded out of 10 keep alive packets that were supposed to be sent over the network.
I32 sysDbaseDownloadCnfgIdxCmd	1.3.6.1.4.1.164.3.3.1.7.2	Integer32	read-write	This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command, the DACS agent will initiate the Sanity-Check process. If successful, the actual transfer will be performed. If there will be errors, the user will have to perform the command again after errors correction. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg.
I32 sysDbaseFlipIdx	1.3.6.1.4.1.164.3.3.1.7.4.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg being the target Configuration.
I32 sysDbaseUploadCnfgIdxCmd	1.3.6.1.4.1.164.3.3.1.7.3	Integer32	read-write	This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg.
I32 sysDclChFailThreshold	1.3.6.1.4.1.164.3.3.1.2.2.1.1.6	Integer32	read-write	This object indicates the number of failed channels that will trigger the redundancy procedure.
I32 sysDclCnfgIdx	1.3.6.1.4.1.164.3.3.1.2.2.1.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. For devices that work on line with NMS (no Temp configuration in NMS), Get and Set will be performed with index value of sysDclCnfgIdx = 1.
I32 sysDclCopyDbIdx	1.3.6.1.4.1.164.3.3.1.2.2.3.1.1	Integer32	read-only	This object indicates the Idx of the Cnfg(1..255) being accessed.
I32 sysDclFlipDelay	1.3.6.1.4.1.164.3.3.1.2.2.1.1.4	Integer32	read-write	If one DCL flip occurred and a second one should be performed, the time from the previous flip is checked. If the time is shorter than the delay specified here, the system should delay the flip operation until time reaches the specified delay. For DXC the values are 1 minute to 4 minutes (1..4). For Optimux-155-1 and Optimux-155-3 the values are: 0...60 Sec. 0 means No Delay.
I32 sysSActiveCnfg	1.3.6.1.4.1.164.3.3.1.3.4	Integer32	read-only	This object specifies the configuration number, that is currently active and running.
I32 sysSAlarmCounter	1.3.6.1.4.1.164.3.3.1.4.1.1.7	Integer32	read-only	A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
I32 sysSAlrAttrIndication	1.3.6.1.4.1.164.3.3.1.3.23	Integer32	read-only	This object indicates the status of the Alarm Attributes for the whole device. It is a sum of 2**(Bit-1). A Bit will be '1', when any alarm in the device is Filtered/Masked/Inverted (respectively). The Bit assignment is: Bit 1: Filter (LSB) Bit 2: Mask Bit 3: Invert (MSB). Examples: - Alarms are filtered and masked but not inverted: value=3 - Alarm is Inverted (not filtered or masked): value=4 - Alarm is masked (not inverted or filtered): value=2
I32 sysSAlrCode	1.3.6.1.4.1.164.3.3.1.4.1.1.2	Integer32	read-only	This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
I32 sysSAlrIdx	1.3.6.1.4.1.164.3.3.1.4.1.1.1	Integer32	read-only	An index number of the current system alarms.
I32 sysSaPorts	1.3.6.1.4.1.164.3.3.1.1.4	Integer32	read-only	This object indicates the ports that are present in the system. Each possible port is represented by a bit. The value of this object is a sum of 2**n, n=number of bits. '1' - means that the port exists '0' - means that the port does not exist For detailed bit assignment, see product's spec. Bit 0 = LSB When this object is not relevant, the value will be 0. In some cases, this object may represent ports configuration of the system AND its far-end unit.
I32 sysSaReadSwch	1.3.6.1.4.1.164.3.3.1.1.5	Integer32	read-write	This object indicates wether the configuration will be read from the DIP switches on the SA (stand alone) unit. Each switch is represented by a bit. If the bit is 1: the configuration will be read from the HW switch position. If the bit is 0: the configuration will be read from the SW user configuration. The DIP switches are different in each of the RAD devices. In the Tiny Router (starting from the LSB) the following switches exist: Bit 0: WAN Loop Bit 1: LAN Full Duplex (When LAN AUI connector, it is SQE) Bit 2: PPP (When WAN 4 Wire connector, it is LONG) Bit 3: IP Learn
I32 sysSaSwchStatus	1.3.6.1.4.1.164.3.3.1.1.1	Integer32	read-only	This object indicates the status of the switches on the SA unit. Each switch is represented by a bit. The status is a sum of 2n, according to the bits. For SMODs products see modem's specification. For DXC product see the following: There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (21 + 2**0). When the status of the switches is unknown, the value of this object will be 255.
I32 sysSBusCapturePort	1.3.6.1.4.1.164.3.3.1.3.21.1.3	Integer32	read-only	The Port that Captured the sysSBusPortIdx. - if sysSBusStatus=free, the value will be 'none'=0 - else, if sysSBusStatus=fixed, the value will be: sysSBusPortIdx - else, the value will be according to the port index that captured this Bus Port (according to DXC port index convention): - xx1, xx3, xx11, xx13, xx31, xx33, xx2..xx56(even numbers) - xx = (IO slot number+10)
I32 sysSBusPortIdx	1.3.6.1.4.1.164.3.3.1.3.21.1.1	Integer32	read-only	The DXC BUS port number: - first two digits will be: (IO slot number+10) - last one/two digits will be the Bus port number, in odd numbers: port1 = 1 port2 = 3 Example: port2 of IO slot 11 will be: 213.
I32 sysSBusUtilization	1.3.6.1.4.1.164.3.3.1.3.21.1.4	Integer32	read-only	Utilization of sysSBusPortIdx resources, in percent [%].
I32 sysSEditCnfg	1.3.6.1.4.1.164.3.3.1.3.5	Integer32	read-only	This object indicates the unique configuration number that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process.
I32 sysSErrIdx	1.3.6.1.4.1.164.3.3.1.3.13.1.2	Integer32	read-only	Unique index number to identify an entry in the error or warning list . The maximum value cannot exceed the value of 'sysSNoOfSanityCheckErr' (actually, the sum of the Errors list max. index and the Warning list max. index should equal the value of'sysSNoOfSanityCheckErr').
I32 sysSMaxNoOfCnfg	1.3.6.1.4.1.164.3.3.1.3.14	Integer32	read-only	Maximum number of configurations that can be defined and stored in the DACS agent. If the DACS agent has a large capacity, the maximum will be limited to 254.
I32 sysSNoOfSanityCheckErr	1.3.6.1.4.1.164.3.3.1.3.12	Integer32	read-only	This object indicates the number of errors/warnings discovered by the last Sanity Check process.
I32 sysSRdnFlipIdx	1.3.6.1.4.1.164.3.3.1.3.18.1.1	Integer32	read-only	Unique index number to identify an entry in the Redundancy Flip list.
I32 sysSRdnFlipPort	1.3.6.1.4.1.164.3.3.1.3.18.1.3	Integer32	read-only	The port number from which Flip was performed. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 100=notApplicable (when Redundancy is at card level).
I32 sysSSelfTestResult	1.3.6.1.4.1.164.3.3.1.3.15	Integer32	read-only	The test is performed by the active Common Logic card. The result will be a sum of 2**n according to the following bit convention: For DXC: bit 0 Database 1 Checksum Error (LSB) bit 1 Database 2 Checksum Error bit 2 I/O Expander Error bit 3 Counter Error bit 4 Matrix DPR Error bit 5 PS-A 5 Volt Error bit 6 PS-A 12 Volt Error bit 7 PS-B 5 Volt Error bit 8 PS-B 12 Volt Error bit 9 EPROM Failure For FCD: bit 0 I/O Expander Error (LSB) bit 1 Counter Error bit 2 EPROM Failure bit 3 Illegal Sys Config bit 4 SFIFO bit 5 EPIC Failure (ISDN) bit 6 XL Flash Fail -- for MSDSL interface bit 7 XL MITEL Fail -- for MSDSL interface bit 8 XL Framer Fail -- for MSDSL interface bit 9 XL DSP Fail -- for MSDSL interface For LRS52 - refer to product's spec When a bit is ('1'), the error exists. When NO ERROR is encountered, this object's value will be 0.
I32 systemNtpGmt	1.3.6.1.4.1.164.6.2.14.4.2	Integer32	read-write	This variable represents the NTP GMT (Greenwich Mean Time), Possible values range is -12..12. For new devices/versions this variable will be in minutes.
I32 systemOamCnfgIdx	1.3.6.1.4.1.164.6.2.36.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
I32 systemOamDescrIdx	1.3.6.1.4.1.164.6.2.36.2.1.1	Integer32	not-accessible	The OAM Descriptor Index.
I32 systemOamFrequency	1.3.6.1.4.1.164.6.2.36.1.1.2	Integer32	read-write	Time in sec. between 2 OAM packets.
I32 systemOamTimeoutCycles	1.3.6.1.4.1.164.6.2.36.1.1.3	Integer32	read-write	No. of cycles the agent will send OAM packets without receiving a response from the remote device before declaring that the connection to the remote side is down - Time Out.
I32 systemParameter	1.3.6.1.4.1.164.6.2.18	Integer32	read-write	This parameter can be used for different purposes: - TELNET session time-out in seconds. - Ace20: when trying to create row in a table that already has row with the same values, if set of values has to be unique in table, this attribute is set to the index of the existing row. - Optimux-T3: when CH interfaces are RJ-45, user can select via this object, the interface type for each Group of channels: T1 or E1: The selection will be a sum of the following Bits. '0' = T1 '1' = E1 Bit Group Value for each Bit having '1' 1 1 (CH-1..CH-8) 1 2 2 (CH-9..CH-12) 2 3 3 (CH-13..CH-20) 4 4 4 (CH-21..CH-28) 8 Examples: 15 = all Groups are selected to be E1 6 = Group 2 and Group 3 are selected to be E1 (Group 1 and Group 4 are T1). - FCD-A, FCD-M: user can select via this object the configuration used for Get values of MSDSL parameters that don't have configuration index. 1 =active configuration 255=temporary configuration. Set of this object should be done before Getting the MSDSL RW parameters. - Ace2002: This parameter indicates the number of intervals that were successfully uploaded upon statistics collection session. - FCD-IP, WR, FCD-IPD, LA-240: This parameter indicates whether Telnet Access is enabled/disabled: Values: 2 - Telnet Access is Disabled. 3 - Telnet Access is Enabled. -Vmux-110: This parameter value equals to maximum number of bundles. -Optimux-155: Simmilar usage to Optimux T3. user can select via this object, interface type T1 or E1 for each Group of channels (LIU): LIU group consists of 7 channels. Up to 12 LIUs are represented (84 T1 Channels). The selection will be a sum of the 2**n For each bit:'0' = T1 ,'1' = E1 Bit Group 1 1 (CH-1 .. CH-7) 2 2 (CH-8 .. CH-14) 3 3 (CH-15 ..CH-21) ... 9 9 (CH-56.. CH-63) ... 10 10 (CH-64..CH-70) 11 11 (CH-71..CH-77) 12 12 (CH-78..CH-84)
I32 systemPsIndex1	1.3.6.1.4.1.164.6.2.25.1.1	Integer32	read-only	First Index. In HUBs: 1 = PS-A slot 2 = PS-B slot 3 = PS-C slot. In SA units: 1 = PS1 2 = PS2 Default = 1
I32 systemPsIndex2	1.3.6.1.4.1.164.6.2.25.1.2	Integer32	read-only	Second Index. In HUBs: 1 always. In SA units: 1 = Local 2 = Remote Default = 1.
I32 systemTimeElapsed	1.3.6.1.4.1.164.6.2.14.3	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period. Same for all ports of the device.
I32 systemVoiceConfIdx	1.3.6.1.4.1.164.3.1.2.12.1.1.1	Integer32	read-only	This attribute indicates the Idx of the Cnfg (1..100) being accessed - Active or Temporary Configurations. Idx 255 relates to the temporary TmpCnfg. All configurations can be read but only the Temporary can be written to.
I32 systemVoiceTxGain	1.3.6.1.4.1.164.3.1.2.12.1.1.9	Integer32	read-write	This object indicates the Transmit Gain (volume) in dB.
I32 tftpRetryTimeOut	1.3.6.1.4.1.164.6.2.12.4	Integer32	read-write	General Retransmission time-out value (seconds)
I32 tftpTotalTimeOut	1.3.6.1.4.1.164.6.2.12.5	Integer32	read-write	Total Retransmission time-out value (seconds)
I32 trapID	1.3.6.1.4.1.164.6.2.11.1.1	Integer32	read-only	This object indicates an index of a specific trap. Can be used also for any trap, while trapVal is used as 'accessible-for-notify' or trapNumeric is used.
I32 trapNumeric	1.3.6.1.4.1.164.6.2.11.1.4	Integer32	accessible-for-notify	This object is a numeric general parameter, that can be attached to any trap. Values can be positive or negative.
I32 wfqCnfgIdx	1.3.6.1.4.1.164.6.3.1.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
I32 wfqPrtIdx	1.3.6.1.4.1.164.6.3.1.1.1.2	Integer32	not-accessible	This object indicates a unique port or interface number, for which Weighted Fair Queueing table is applicable . For numbering, see product's spec. For some products, the numbering can equal ifIndex. Value of 255 (not applicable) refer to system level queue
I32 wfqQueueIdx	1.3.6.1.4.1.164.6.3.1.1.1.4	Integer32	not-accessible	This object indicates a queue index. For FCD-155, valid queues are 1..3. The 4th queue is not in MIB. Its weight will be RO, Calculated according to the sum of the 3 first queues.
I32 wfqTblIdx	1.3.6.1.4.1.164.6.3.1.1.1.3	Integer32	not-accessible	This object indicates which Weighted Fair Queueing (WFQ) Table is being used. There can be several tables. For FCD-155 User will select which one will be used for a virtual concatenation group.Valid values are 1,2
I32 wfqWeightValue	1.3.6.1.4.1.164.6.3.1.1.1.6	Integer32	read-create	This object indicates a relative weight value. User should make sure that the sum of values for all queues will not exceed 100% (sum should be BELOW 100% in order to leave some BW percentage for last queue) Note that when this attribute is being used, the wfqMinRateAbsolute attribute is NA.
I32 wrDhcpIpAddressLeaseTime	1.3.6.1.4.1.164.11.7.2.2.1.2.1.9	Integer32	read-create	Allocated IP Address lease time in seconds. A zero value specifies no time limitation.
I32 wrIpIfIndex	1.3.6.1.4.1.164.11.7.2.4.1.1.1	Integer32	read-only	Port interface index.
I32 wrLanIfIndex	1.3.6.1.4.1.164.11.7.2.3.2.1.1	Integer32	read-only	LAN port ifIndex.
I32 wrLanIfRdnTimeout	1.3.6.1.4.1.164.11.7.2.4.3.1.4	Integer32	read-write	LAN Redundancy Timeout in seconds. Applicable when wrLanIfState=redundancy.
I32 wrSpoofingAction	1.3.6.1.4.1.164.11.7.2.4.2.1.2	Integer32	read-create	Spoofing action is applied by bit code: enable : bit 0 set (disable: bit 0 is 0) keepAlive : bit 1 ... : bit 2 and so on. For the above example, to set spoofing to keepAlive action, the object's value will be 3 = [ 20 + 21 ] Only the Remote WEBRANger will accept this object ! -------
I32 wrSpoofingAgingStation	1.3.6.1.4.1.164.11.7.2.4.2.1.3	Integer32	read-create	Aging time of stations list, in min. The agent 'translates' the time entered in minutes, to 10 min. resolution, as follows: 1..10 min - 10 min 11..20 min - 20 min and so on... 0 is not a valid value. Only the Remote WEBRANger will accept this object ! ----------------
I32 wrSpoofingIfIndex	1.3.6.1.4.1.164.11.7.2.4.2.1.1	Integer32	read-only	Port interface index.
I32 wrSyncIfIndex	1.3.6.1.4.1.164.11.7.2.4.4.1.1	Integer32	read-only	Sync interface index.
I32 xcBitMapping	1.3.6.1.4.1.164.6.2.31.1.12	Integer32	read-only	This object maps this entry to a bit of an octet string. For ACE2002 this object maps the LAN VCC to the bit of the VLAN Port Lists. If the value is '0' then it means that this VCC is not mapped to a port list or it may be an HDSL entry.
I32 xcIfIndex1	1.3.6.1.4.1.164.6.2.31.1.2	Integer32	not-accessible	The interface Index from the ifTable, which identify one side of the connection.
I32 xcIfIndex2	1.3.6.1.4.1.164.6.2.31.1.5	Integer32	not-accessible	The interface Index from the ifTable, which identifies the other side of the connection.
I32 xcIndex	1.3.6.1.4.1.164.6.2.31.1.1	Integer32	not-accessible	Cross Connect Identifier.
I32 xcIndexNext	1.3.6.1.4.1.164.6.2.30	Integer32	read-only	This object contains an appropriate value to be used for xcIndex when creating entries in the xcTable. The value 0 indicates that no unassigned entries are available. To obtain the xcIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
I32 xcInputPriority	1.3.6.1.4.1.164.6.2.31.1.11	Integer32	read-create	This object is the priority, by which the LAN frames will be internaly sent to the ATM HW. This parameter is applicable if atmNteMdlInputPriorityMechanism=enabled. 1 - Highest priority. Will be the first to be sent to the ATM HW. 4 - Lowest priority. Will be the last to be sent to the ATM HW.
I32 xcVci	1.3.6.1.4.1.164.6.2.31.1.4	Integer32	not-accessible	The VCI value.
I32 xcVpi	1.3.6.1.4.1.164.6.2.31.1.3	Integer32	not-accessible	The VPI value.
InterfaceIndex (4)
NUM atmNtePlugAndPlayIfIndex	1.3.6.1.4.1.164.12.3.1.1.24	InterfaceIndex	read-write	The ifIndex of the Plug and Play VCC.
NUM atmSysConfigCellTestPort	1.3.6.1.4.1.164.12.3.1.1.33.1	InterfaceIndex	read-write	An Index of the port on which the cell test will be sent.
NUM dsx3MappingDs3Index	1.3.6.1.4.1.164.3.1.6.3.3.1.1	InterfaceIndex	not-accessible	The index value which uniquely identifies the DS3/E3 interface to which this entry is applicable. This value is also equal to dsx3LineIndex used in dsx3ConfigEntry. For RICi-16 this is the ifIndex of the T3 interface.
NUM dsx3MappingIfIndex	1.3.6.1.4.1.164.3.1.6.3.3.1.3	InterfaceIndex	read-write	An index value that uniquely identifies a logical or physical interface mapped to a DS3/E3 channel. If no interface is currently using a channel, the value should be zero. If a single interface occupies more than one channel, that ifIndex value will be found in multiple channels. For RICi-16 this is the ifIndex of the T1 or VCG interface.
IpAddress (58)
IP agnCBuMlDefaultGateway	1.3.6.1.4.1.164.3.1.2.2.12.1.4	IpAddress	read-write	Default Gateway's IP Address.
IP agnCBuMlSubnetMask	1.3.6.1.4.1.164.3.1.2.2.12.1.5	IpAddress	read-write	The Link subnet mask.
IP agnCnfgUpdMnger	1.3.6.1.4.1.164.3.1.2.2.7.1.5	IpAddress	read-only	This object indicates the IP Address of the Manager who performed the last update of this configuration. When update is performed, the agent should save the IP Address of the Manager who commanded the update. That will enable a manager to know if he performed the last update, or another manager did.
IP atmNteHostDefaultNextHop	1.3.6.1.4.1.164.12.3.1.1.11.1.10	IpAddress	read-create	The host interface Default Next Hop address. This address will be used as default next hop for every Bundle mapped to this Host.
IP atmNteHostIP	1.3.6.1.4.1.164.12.3.1.1.11.1.2	IpAddress	read-create	The host interface IP address.
IP atmNteHostMask	1.3.6.1.4.1.164.12.3.1.1.11.1.3	IpAddress	read-create	The host interface subnet mask.
IP atmNteManagerIP	1.3.6.1.4.1.164.12.3.1.1.1.1.1	IpAddress	read-only	The IP address of the NMS.
IP atmNteManagerNextHop	1.3.6.1.4.1.164.12.3.1.1.1.1.8	IpAddress	read-create	This parameter is relevant to Ethernet out of band host only (PVC=10). The Next Hop IP address of the entry route.
IP autoFileTransferServerIp	1.3.6.1.4.1.164.6.2.12.13.1.1.2	IpAddress	read-write	This object defines the IP Address of the server to which the file is uploaded.
IP dhcpClientServerIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.6.1.2	IpAddress	read-write	DHCP Server IP Address.
IP dhcpIfClientIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.7.1.2	IpAddress	read-create	DHCP Client IP Address.
IP dhcpPoolAllocLeasingIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.2	IpAddress	read-only	Single IP Address belonging to dhcp pool whose Lowest Ip Address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing or may be leased by Host its MacAddress is dhcpPoolAllocMacAddress. All posible statuses of IP address are indicated by dhcpPoolAllocFlags
IP dhcpPoolAllocLowIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.1	IpAddress	read-only	Lowest IP address of this pool, value eqaul to wrDhcpLowIpAddress for the pool.
IP dhcpRelayServerIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.4.1.2	IpAddress	read-write	DHCP Server IP Address.
IP fileServerIP	1.3.6.1.4.1.164.6.2.12.1	IpAddress	read-write	The IP address of the server from which the file is loaded
IP hostDefaultNextHop	1.3.6.1.4.1.164.6.2.40.1.4	IpAddress	read-create	The host interface Default Next Hop address.
IP hostIP	1.3.6.1.4.1.164.6.2.40.1.2	IpAddress	read-create	The host interface IP address.
IP hostIPMask	1.3.6.1.4.1.164.6.2.40.1.3	IpAddress	read-create	The host interface subnet mask.
IP ip2IfDestAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.5	IpAddress	read-create	The destination IP address.
IP ip2IfNextHop	1.3.6.1.4.1.164.3.1.6.7.1.1.6	IpAddress	read-create	The next hop to which the frame should be sent. Default value - 0.0.0.0. Upon setting the default value the frame is sent to the default Gateway.
IP ip2IfSourceAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.25	IpAddress	read-create	Source IP Address of the bundle.
IP ip2IfTdmBackUpNextHop	1.3.6.1.4.1.164.3.1.6.7.1.1.30	IpAddress	read-create	Defines the TDM bundle default router in case there was a switch from the Primary Link (for example an ETH port) to a TDM backup Link like E1, T1 or Serial Link. This parameter is relevant only when a Backup Link is configured. When a Backup Link is not configured the value will be: 0.0.0.0
IP mdlProtIpAddress	1.3.6.1.4.1.164.3.2.2.1.2.1.3	IpAddress	read-only	A Protected IP address.
IP mdlStatDefaultGateway	1.3.6.1.4.1.164.3.2.2.2.1.1.4	IpAddress	read-only	Default Gateway's IP Address when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
IP mdlStatHostIP	1.3.6.1.4.1.164.3.2.2.2.1.1.2	IpAddress	read-only	The host interface IP address when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
IP mdlStatHostMask	1.3.6.1.4.1.164.3.2.2.2.1.1.3	IpAddress	read-only	The host interface subnet mask when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
IP mngIP	1.3.6.1.4.1.164.6.2.7.1.2	IpAddress	read-write	This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.
IP mngIPMask	1.3.6.1.4.1.164.6.2.7.1.3	IpAddress	read-write	This value indicates the mask of the destination addresses of the traps.
IP prtExPVc4DefaultGateway	1.3.6.1.4.1.164.3.2.3.2.9.1.1.51	IpAddress	read-write	This object defines the Default Gateway for this interface.
IP prtExPVc4DestIp	1.3.6.1.4.1.164.3.2.3.2.9.1.1.47	IpAddress	read-write	This object defines the destination IP Address.
IP prtExPVc4SrcIpAddress	1.3.6.1.4.1.164.3.2.3.2.9.1.1.49	IpAddress	read-write	This object defines the Source IP Address.
IP prtExPVc4SrcIpMask	1.3.6.1.4.1.164.3.2.3.2.9.1.1.50	IpAddress	read-write	This object defines the Source IP Mask.
IP prtIpParamDefaultGateway	1.3.6.1.4.1.164.6.2.15.6.1.1.6	IpAddress	read-write	Default Gateway's IP Address.
IP prtIpParamHostIP	1.3.6.1.4.1.164.6.2.15.6.1.1.4	IpAddress	read-write	The host interface IP address.
IP prtIpParamHostMask	1.3.6.1.4.1.164.6.2.15.6.1.1.5	IpAddress	read-write	The host interface subnet mask.
IP prtIpParamRemoteIP	1.3.6.1.4.1.164.6.2.15.6.1.1.15	IpAddress	read-write	This is the IP Address of the remote device that is connected to the current device (Point to Point Application). It is used for sending OAM packets on the LAN to the remote side in order to check that the connection is OK.
IP prtIsdnStatusCalledIP	1.3.6.1.4.1.164.3.2.3.1.16.1.5	IpAddress	read-only	This is the remote IP Address associated with this entry.
IP prtMl4IpAddress	1.3.6.1.4.1.164.3.2.3.2.19.1.1.10	IpAddress	read-write	IP Address of the port.
IP prtMl4IpMask	1.3.6.1.4.1.164.3.2.3.2.19.1.1.11	IpAddress	read-write	IP subnet mask of the port.
IP prtTestDestinationIpAddress	1.3.6.1.4.1.164.6.2.15.4.1.1.23	IpAddress	read-write	Indicates the destination IP Address in the transmitted messages that are looped back.
IP qosFlowMappingFromDestIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.18	IpAddress	read-create	This attribute determines the first destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.
IP qosFlowMappingFromSrcIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.16	IpAddress	read-create	This attribute determines the first source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.
IP qosFlowMappingToDestIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.19	IpAddress	read-create	This attribute determines the last destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.
IP qosFlowMappingToSrcIpAddr	1.3.6.1.4.1.164.6.3.9.2.1.17	IpAddress	read-create	This attribute determines the last source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.
IP radBridgeCODIPMask	1.3.6.1.4.1.164.4.1.4.3.3	IpAddress	read-write	This is the Mask of the Remote IP Address
IP radBridgeCODRemoteIPAddr	1.3.6.1.4.1.164.4.1.4.3.2	IpAddress	read-write	This is the Remote IP Address
IP systemDefaultGateway	1.3.6.1.4.1.164.6.2.24	IpAddress	read-write	Default Gateway's IP Address.
IP wrDhcpDefaultGateway	1.3.6.1.4.1.164.11.7.2.2.1.2.1.4	IpAddress	read-create	Default Gateway's IP Address.
IP wrDhcpHighIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.2	IpAddress	read-create	DHCP High Ip Address.
IP wrDhcpIpMaskAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.3	IpAddress	read-create	IP mask Address.
IP wrDhcpLowIpAddress	1.3.6.1.4.1.164.11.7.2.2.1.2.1.1	IpAddress	read-create	DHCP Low Ip Address.
IP wrDhcpPrimaryDNS	1.3.6.1.4.1.164.11.7.2.2.1.2.1.5	IpAddress	read-create	Primary DNS.
IP wrDhcpSecondaryDNS	1.3.6.1.4.1.164.11.7.2.2.1.2.1.6	IpAddress	read-create	Secondary DNS.
IP wrDhcpTftpServerIp	1.3.6.1.4.1.164.11.7.2.2.1.2.1.11	IpAddress	read-create	DHCP pool - TFTP-server IP Address.
IP wrDialInIpxNet	1.3.6.1.4.1.164.11.7.2.3.3	IpAddress	read-write	Net address through a link.
IP wrIpAddress	1.3.6.1.4.1.164.11.7.2.4.1.1.2	IpAddress	read-create	Link IP Address.
IP wrIpMask	1.3.6.1.4.1.164.11.7.2.4.1.1.3	IpAddress	read-create	Link IP mask Address.
IP wrIpxNetAddress	1.3.6.1.4.1.164.11.7.2.3.2.1.3	IpAddress	read-write	Net address per Frame Type & LAN port.
LldpPortIdSubtype (2)
LLD radMepLtrEgressPortIdSubtype	1.3.6.1.4.1.164.3.1.6.1.3.4.1.9	LldpPortIdSubtype	read-only	The format of the egress Port ID. If the radMepLtrEgress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:q and 20.36.2.12
LLD radMepLtrIngressPortIdSubtype	1.3.6.1.4.1.164.3.1.6.1.3.4.1.6	LldpPortIdSubtype	read-only	The format of the Ingress Port ID. If the radMepLtrIngress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:m and 20.36.2.8
MacAddress (19)
MAC dhcpPoolAllocMacAddress	1.3.6.1.4.1.164.11.7.2.2.1.3.1.3	MacAddress	read-only	MAC Address to which the IP address has been leased
MAC dot1agXCfmMepDestMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.9.1.3	MacAddress	read-create	This object determines the MAC address that OAM packets are sent to.
MAC ethFlowCtrlMacAddress	1.3.6.1.4.1.164.3.1.6.1.1.1.14	MacAddress	read-write	In case of flow control - transmit frame with this specific MAC address to inform the other end to stop sending frames. Default: 01.80.C2.00.00.01.
MAC ethIfSrcMacCtrlAddr	1.3.6.1.4.1.164.3.1.6.1.7.2.1.2	MacAddress	not-accessible	A unicast source MAC address that was learned or statically configured for the current interface. Packets with this source MAC address will be accepted by the device.
MAC ethIfSrcMacCtrlLastViolatingAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.10	MacAddress	read-write	This object indicates the last MAC address that violated the security on the current interface. If no violation, the agent will return: 00-00-00-00-00-00 .
MAC ethOamStdMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.7	MacAddress	read-write	The Standard MAC Address in an OAM message. This object will be RW until a formal value will be issued for standard MAC Address. When such Standard will exist, this object will be supported RO to reflect the Standard value.
MAC ip2IfMacAddr	1.3.6.1.4.1.164.3.1.6.7.1.1.8	MacAddress	read-create	The Destination MAC address of the next hop or destination station.
MAC prtIpParamRingAdjacentMacAddr	1.3.6.1.4.1.164.6.2.15.6.1.1.38	MacAddress	read-only	The MAC address of the adjacent NE connected to this port in an ETH ring. If the port is not a member of a ring, the value of this parameter will be 00-00-00-00-00-00.
MAC prtTestMacSwapLoopDestAddr	1.3.6.1.4.1.164.6.2.15.4.1.1.17	MacAddress	read-write	Configures the MAC address that will be sent in the Destination field of the packet in the outgoing direction.
MAC prtTestMacSwapLoopSrcAddr	1.3.6.1.4.1.164.6.2.15.4.1.1.18	MacAddress	read-write	Configures the MAC address that will be sent in the Source field of the packet in the outgoing direction.
MAC qosFlowMappingFromDestMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.14	MacAddress	read-create	This attribute determines the first destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingFromSrcMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.12	MacAddress	read-create	This attribute determines the first source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingToDestMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.15	MacAddress	read-create	This attribute determines the last destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.
MAC qosFlowMappingToSrcMacAddr	1.3.6.1.4.1.164.6.3.9.2.1.13	MacAddress	read-create	This attribute determines the last source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.
MAC radMepCcStatusMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.5.1.4	MacAddress	read-only	This object indicates the MAC Address in the CC Status message received.
MAC radMepLtrMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.4.1.3	MacAddress	read-only	The MAC address in the header of the returned LTR.
MAC radMepOamDestMacAddr	1.3.6.1.4.1.164.3.1.6.1.3.1.1.11	MacAddress	read-create	This object determines the MAC address that OAM packets are sent to.
MAC radMepTransmitLbmDestMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.1.1.20	MacAddress	read-create	The Target MAC Address Field to be transmitted in the Loopback Message: For unicast MAC Address this is the unicast destination MAC address. For multicast MAC Address, this variable is read-only. This address will be used if the value of radMepTransmitLbmDestIsMepId is no (2). 802.1ag clause 12.14.7.3.2:b.
MAC radMepTransmitLtmTargetMacAddress	1.3.6.1.4.1.164.3.1.6.1.3.1.1.29	MacAddress	read-create	The Target MAC Address Field to be transmitted in the Link Trace Message: A unicast destination MAC address. This address will be used if the value of radMepTransmitLtmTargetIsMepId is no (2). 802.1ag clause 12.14.7.4.2:c.
OBJECT IDENTIFIER (9)
OID agnRowPointerIndex	1.3.6.1.4.1.164.6.2.63.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of an entry in a table.
OID agnSpecific	1.3.6.1.4.1.164.6.2.5	OBJECT IDENTIFIER	read-only	Object identifier of entity containing additional information regarding this instance.
OID agnStringToIndexTableId	1.3.6.1.4.1.164.6.2.62.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of the Table, having as index numeric values. In this table, the value of agnStringToIndexUserName is an attribute.
OID invNameXCType	1.3.6.1.4.1.164.6.2.41.1.2	OBJECT IDENTIFIER	read-only	The OBJECT IDENTIFIER of the respective XC Table. Examples: XC Table invNameXCType --------------------------------------------------- atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .
OID maskingSmartMaskOID	1.3.6.1.4.1.164.4.1.6.3.1.5	OBJECT IDENTIFIER	read-only	A reference to a specific Smart mask table (old radBridgeMaskTable) which enables a more specific mask type. If this information is not available, its value should be set to the OBJECT IDENTIFIER { 0 0 }.
OID prtExPh1MlTsExt	1.3.6.1.4.1.164.3.2.3.2.2.2.1.8	OBJECT IDENTIFIER	read-only	A pointer to an extension of this table: prtExTsSplitTable. - If prtExPh1MlTsIConSlot='split', its value should be set to the OBJECT IDENTIFIER of the prtExTsSplitTable, with its relevant CnfgIdx, SltIdx, PrtIdx, TsIdx and 1st TsBit. - If prtExPh1MlTsIConSlot is not 'split', its value should be set to the OBJECT IDENTIFIER { 0 0 }.
OID radBridgeCODSpecificOnTrafficOIDCondition	1.3.6.1.4.1.164.4.1.4.4.1.6	OBJECT IDENTIFIER	read-only	A reference to a specific entry in the radBridgeMaskTable, which describes the particular COD condition . If Connect or Disconnect Conditions are not onTraffic, its value should be set to the OBJECT IDENTIFIER { 0 0 }.
OID rowInfoTableId	1.3.6.1.4.1.164.6.2.43.1.1	OBJECT IDENTIFIER	not-accessible	The OBJECT IDENTIFIER of the Table, which its information is held by this table (rowInfoTable). Examples: Table Name rowInfoTableId --------------------------------------------------- atmTrafficDescrParamTable 1.3.6.1.2.1.37.1.5 atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .
OID sysSRdnFlipCmd	1.3.6.1.4.1.164.3.3.1.3.20	OBJECT IDENTIFIER	read-write	This object enables the user to send a command to the Agent, to Flip from a current Online IO card to its Redundant card. The value sent will be an Object Identifier of an entry in the sysCRdnTable. This entry defines the Redundant couple of Slots on which the Flip is applied. Setting this object, will cause the Agent to Flip from current Online card to its Redundant card. This manual flip command is applicable only for entries having Redundancy Mode=Y Cable. For Vmux: This command will cause flipping from Secondary or Third Link to the Primary Link. If the active link is the primary link, the agent will flip to the secondary link. The value sent will be the Object Identifier of the following Table: agnCBuMlTable. Agent will send the value 0 for Get.
OCTET STRING (106)
OCT agnAlarmsCmprObj	1.3.6.1.4.1.164.3.1.2.3.3.1.3	OCTET STRING	read-only	This attribute is the compressed information itself.
OCT agnAlrBufCmprObj	1.3.6.1.4.1.164.3.1.2.3.4.1.3	OCTET STRING	read-only	This attribute is the compressed information itself.
OCT agnCmprObj	1.3.6.1.4.1.164.3.1.2.3.1.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
OCT agnConfigMsg	1.3.6.1.4.1.164.6.2.6	OCTET STRING	read-only	Full configuration message coded in internal RAD application format. This entry describes agent's configuration. For MP-2200 R3, this object describes agent's support of the V5.1 feature: 1 octet ; bit 0 (LSB). '1' - V5.1 feature is supported '0' - V5.1 feature is not supported.
OCT agnDeviceCapabilities	1.3.6.1.4.1.164.6.2.42	OCTET STRING	read-only	Indicates the optional capabilities that are implemented by this device and are manageable through this MIB. For each capability 1 BIT is allocated in each Octet starting from the LSB. If the value of the BIT = 1, the capability is Enabled. If the value of the BIT = 0, the capability is Disabled. For bit assignment, refer to device specification. Capabilities example: Router - BIT 0 (0000 0001 = 01 Hex = 1 Decimal). The 2nd octet (MSB) will represent the maximum number of intervals that the Agent can keep in its DB (same for all ports). For Vmux, this object describes agent's support of LBRAD coder feature: 1 octet ; bit 0 (LSB). '1' - LBRAD feature is supported '0' - LBRAD feature is not supported.
OCT agnDlciCmprObj	1.3.6.1.4.1.164.3.1.2.3.2.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
OCT agnFans	1.3.6.1.4.1.164.6.2.26	OCTET STRING	read-only	This entry specifies the FANs existence and status. Each fan will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each fan: 00 - FAN does not exist 01 - FAN exists and OK (Low Mode) 10 - High Mode (FAN OK) 11 - FAN exists and is Failed bits 0-1 are for first fan bits 2-3 are for 2nd fan (if exists) bits 4-5 are for 3nd fan (if exists) bits 6-7 are for 4nd fan (if exists) bits 8-9 are for 5nd fan (if exists) bits 10-11 are for 6nd fan (if exists) bits 12-13 are for 7nd fan (if exists) bits 14-15 are for 8nd fan (if exists).
OCT agnGlobalAlarmMask	1.3.6.1.4.1.164.6.2.19	OCTET STRING	read-write	The value of this attribute determines the alarm traps the agent should mask and not send to the managers. Each bit from a certain octet represents a certain alarm.
OCT agnLed	1.3.6.1.4.1.164.6.2.10	OCTET STRING	read-only	This entry specifies the LEDs status of the agent module . Each led will be represented by 4 bits where the first 2 bits (left) will specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY)
OCT agnSCmprErrObj	1.3.6.1.4.1.164.3.1.2.3.5.1.3	OCTET STRING	read-only	This attribute is a full text description of the error, including: error code, slot and port numbers related to the code .
OCT agnSensorsStatus	1.3.6.1.4.1.164.6.2.28	OCTET STRING	read-only	This entry specifies the Sensors (Temperature sensors or others) existence and status. Each sensor will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each sensor: 00 - sensor does not exist 01 - sensor exists and status is OK 11 - sensor exists and status is not OK ( e.g. temperature exceeds pre-defined threshold) bits 0-1 are for first sensor bits 2-3 are for 2nd sensor (if exists) and so on... Bit 0 is the LSB.
OCT agnSigProfileABCD	1.3.6.1.4.1.164.3.1.2.10.1.1.4	OCTET STRING	read-write	For MP-2100/MP-2200 and for MP-104/204 from R2: This object represents 6 parameters, by 3 Octets : Busy Code-MSB nibble, - applicable only for Rx translation Idle Code- nibble, - applicable only for Rx translation D Bit Code- nibble, C Bit Code- nibble, B Bit Code- nibble, A Bit Code-LSB nibble. Each of Busy and Idle Code nibble will have the valid values: 0000 .. FFFF. Each of A,B,C,D Bit Code nibble represents: 0 hex = 0000 = 0 1 hex = 0001 = 1 2 hex = 0010 = A bit 3 hex = 0011 = B bit 4 hex = 0100 = C bit 5 hex = 0101 = D bit 6 hex = 0110 = A bit inverse 7 hex = 0111 = B bit inverse 8 hex = 1000 = C bit inverse 9 hex = 1001 = D bit inverse A-F hex - not used (invalid values) For MP-104/204 R1: This object represents 3 parameters, by 2 Octets : Bit 1 = Bit A - OFF Hook for Tx ; Ring for Rx (LSB) Bit 2 = Bit B - OFF Hook for Tx ; Ring for Rx Bit 3 = Bit C - OFF Hook for Tx ; Ring for Rx Bit 4 = Bit D - OFF Hook for Tx ; Ring for Rx Bit 5 = Bit A - ON Hook for Tx ; Idle for Rx Bit 6 = Bit B - ON Hook for Tx ; Idle for Rx Bit 7 = Bit C - ON Hook for Tx ; Idle for Rx Bit 8 = Bit D - ON Hook for Tx ; Idle for Rx Bit 9 = Bit A - OOS State for both Tx and Rx Bit 10 = Bit B - OOS State for both Tx and Rx Bit 11 = Bit C - OOS State for both Tx and Rx Bit 12 = Bit D - OOS State for both Tx and Rx Bit 13 = Spare (always 0) Bit 14 = Spare (always 0) Bit 15 = Spare (always 0) Bit 16 = Spare (always 0) (MSB) When the object is not applicable, the Octet String will have 0 bytes.
OCT agnTrapValue	1.3.6.1.4.1.164.6.2.3	OCTET STRING	read-only	The value of the trap decoded in internal RAD format. Full description is given in the Trap definition file
OCT agnTsCmprData	1.3.6.1.4.1.164.3.1.2.3.6.1.6	OCTET STRING	read-write	This object is the compressed information itself. It provides information about all TSs of a port.
OCT agnXCmprObj	1.3.6.1.4.1.164.3.1.2.3.7.1.8	OCTET STRING	read-write	This attribute is the compressed information itself.
OCT atmConfVpCongestionControl	1.3.6.1.4.1.164.12.3.2.1.3.1.5	OCTET STRING	read-write	Each bit indicates a selection of one option as the following description. All combinations are possible and legal. The codes are: 1 - EPD 2 - CLP 4 - EFCI
OCT atmConfVpLoopbackSinkAddress	1.3.6.1.4.1.164.12.3.2.1.3.1.4	OCTET STRING	read-write	Destination address. For ace101: 2 bytes are used. For ace2002: 16 bytes are used.
OCT atmNteConfLoopbackSourceAdd	1.3.6.1.4.1.164.12.3.1.1.9.3.2	OCTET STRING	read-write	Loopback source address. This field is relevant when atmNteConfOamAddMode is on.
OCT atmNteManagerAlarmTrapMask	1.3.6.1.4.1.164.12.3.1.1.1.1.12	OCTET STRING	read-create	The value of this object determines the alarm traps that the agent should mask and not send to this NMS. The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. More details on the masked traps exist in the product specification. For products that do not mask specific traps, the value of the bits will be 0.
OCT atmNteTosHighPriority	1.3.6.1.4.1.164.12.3.1.1.16	OCTET STRING	read-write	Priorities options are High or Low. High priority will be represented by bit = 1. Low priority will be represented by bit = 0. Each TOS value will be represented by the bit location. For example, the string for TOS 2, 9, 15 with High priority, will be: \|0000 0000\|... ...\|0000 0000\|1000 0010\|0000 0100\| ...98 7654 3210 (Bit #) 8 ... 3 2 1 (Byte #).
OCT atmNteTosMask	1.3.6.1.4.1.164.12.3.1.1.15	OCTET STRING	read-write	This parameter determines the seqence of bits that will be used for TOS. For ACE101 this parameter is applicable only if atmNteTosMode = enable. Valid only for IP-TOS process.
OCT atmSysConfigCellTestPayload	1.3.6.1.4.1.164.12.3.1.1.33.7	OCTET STRING	read-write	The payload of the cell. For OAM cell the payload is set automatically to 6A.
OCT bitMappingView	1.3.6.1.4.1.164.6.2.39	OCTET STRING	read-only	A view of the bitMappingTable in one object - each entry in the biMappingTable will have the corresponding Bit of this object (bitMappingLocation) = '1'. For ACE-2002 it is used to describe all the existing LAN VCC's So that the NMS can easily calculate which VCC's can be selected as members for a VLAN, instead of reading all the bitMapping Table.
OCT cmprObj	1.3.6.1.4.1.164.3.3.4.1.1.6	OCTET STRING	read-write	This object is the compressed information itself, according to a predefined format, both agent and NMS agreed about.
OCT cosProfileCosMapping	1.3.6.1.4.1.164.6.3.10.1.5	OCTET STRING	read-create	This attribute defines the value of the CoS that is assigned for each priority. The number of the valid octets depends upon the priority method selected: Octet 0 corresponds to priority = 0 Octet 1 corresponds to priority = 1 ... Octet 63 corresponds to priority = 63.
OCT dsx1CurrentStatus	1.3.6.1.4.1.164.3.1.6.4.1.2.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
OCT dsx1IntervalStatus	1.3.6.1.4.1.164.3.1.6.4.1.3.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
OCT dsx1TsEchoCancel	1.3.6.1.4.1.164.3.1.6.4.2.1.13	OCTET STRING	read-write	This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., 4th octet bit'7' = TS#32. Octets and bits order is from left to right: [31,30,..24] [23..16] [15..8] [7..0] MSB LSB MSB LSB MSB LSB MSB LSB For each bit values are: 0 - Echo-Cancellation off. 1 - Echo-Cancellation on.
OCT ethIfCurrentStatus	1.3.6.1.4.1.164.3.1.6.1.2.1.1.2	OCTET STRING	read-only	The status of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
OCT ethIfIntervalStatus	1.3.6.1.4.1.164.3.1.6.1.2.2.1.3	OCTET STRING	read-only	The status of the interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
OCT fileTransferToSubSystems	1.3.6.1.4.1.164.6.2.12.8	OCTET STRING	read-write	This object represents the sub-systems the fileTransCmd refers to. It should be used when a system is divided to sub-systems and each sub-system (or part of them) can have a different SW/Configuration. Each bit of this object will represent one of the sub-systems. Bit='1' - APPLY to respective sub-system Bit='0' - DO NOT APPLY to respective sub-system For the meaning of each bit, see product's specification. User will select the sub-systems envolved by filling-in the bits that represent these sub-systems. In this case, the file represented by 'fileName' will include several parts, each representing one of the sub-systems. The agent will refer only to the part/s indicated by this object. 0 Octet Strings = not applicable DEFVAL = 0h for the products that support this object.
OCT ifTeQosParam	1.3.6.1.4.1.164.6.3.3.1.1.4	OCTET STRING	read-write	This object is used for QOS attributes of the entry's entities.
OCT ifTeQosParam2	1.3.6.1.4.1.164.6.3.3.1.1.5	OCTET STRING	read-write	This object is used for 2nd group QOS attributes of the entry's entities.
OCT intSwdlToSubSystem	1.3.6.1.4.1.164.6.2.12.10.1.8	OCTET STRING	read-write	This object defines the subsystem for download. Bit='1'- APPLY to respective sub system. Bit='0'- DO NOT APPLY to respective sub system. For more details see product specification. For every octet bit0=LSB, bit7=MSB
OCT ip2IfDataOos	1.3.6.1.4.1.164.3.1.6.7.1.1.17	OCTET STRING	read-create	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT ip2IfModemProtocolMode	1.3.6.1.4.1.164.3.1.6.7.1.1.84	OCTET STRING	read-create	This octet string contains the mode of each Modem Protocol used on the bundle. For each protocol one octet will be used. Octet #1 will be used for V.22 Protocol. Octet #2, #3, #4... are reserved for future protocols. Octet #1 values: 0 - Not Applicable 1 - VBD: Voice Band Data. 2 - Relay: Pulse Code Modulated (PCM) data is sent via the bundle. For V.22: This MIB object is relevant only when ip2IfModemCalls = relay (4).
OCT ip2IfOAM	1.3.6.1.4.1.164.3.1.6.7.1.1.19	OCTET STRING	read-create	This parameter determine the OAM configuration. The LSB (Bit 0 the most right one) is used for OAM connectivity. Values: 0 = disable, 1= enable.
OCT ip2IfSuperTandemBitMask	1.3.6.1.4.1.164.3.1.6.7.1.1.86	OCTET STRING	read-create	This MIB object enables controlling the Time Slot/Channel rate. Valid values: 1 - FF HEX Each BIT represents 1/8 of the TS. Example: 7E (0111 1110) means that 6/8 of the TS (the center ones) are masked and data will be Tx/Rx only through them. This MIB object is relevant only when Super Tandem is enabled.
OCT ip2IfVoiceOos	1.3.6.1.4.1.164.3.1.6.7.1.1.16	OCTET STRING	read-create	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT markingSpVlanPBit	1.3.6.1.4.1.164.6.3.12.1.4	OCTET STRING	read-create	For ETX-202A : This attribute defines the value of the SP VLAN P-Bit that is assigned for each CoS: Octet 0 corresponds to CoS = 0 Octet 1 corresponds to CoS = 1 ... Octet 7 corresponds to CoS = 7. For LA-210 from V1.5 : This attribute defines the value of the SP VLAN P-Bit that is assigned for each frame according to the value of markingProfileMethod parameter : Octet 0 corresponds to value 0 of 802.1 P-bit/DSCP/TOS. Octet 1 corresponds to value 1 of 802.1 P-bit/DSCP/TOS. ... Octet 7 corresponds to value 7 of 802.1 P-bit/DSCP/TOS. Octets 8-63 correspond to DSCP values 8-63.
OCT mdlAlarmsCmprObj	1.3.6.1.4.1.164.3.1.3.3.2.1.4	OCTET STRING	read-write	This attribute is the compressed information itself.
OCT mdlAlrMask	1.3.6.1.4.1.164.3.3.2.1.3.2.1.2	OCTET STRING	read-write	This object is a mask that indicates which card level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the card level will be 0. This object is applicable only when mdlSAlrMaskAll=off (otherwise all card alarms are masked). Example: When Alarm having the code 8 is masked, the value of this object will be 100 (hex).
OCT mdlCInterfaces	1.3.6.1.4.1.164.3.1.3.2.1.1.9	OCTET STRING	read-only	Octet string which indicates 'present' interfaces in card. Each '0' bit stands for non-present interface. Each '1' bit stands for present interface. For ASMi54C card of LRS-102 and MP-4100 notPresent interfaces may be: - SHDSL Line ID with no wire pairs assigned to it (does not exist in ifTable) - PCS without SHDSL Line binded to it, (exist in ifTable, with ifOperStatus= notPresent) - External DS1 when its LIU is used by an Internal DS1 of the same card - Internal DS1 when single bearer is not TDM. In each octet, MS bit represents port 1 and LS bit represents port 8 MSB LSB 1 0 0 0 1 0 0 0 -- Example: Port # 1 and 5 are present. Port 1 2 3 4 5 6 7 8 1st Octet (MSB octet) represents SDHSL Lines 2nd Octet represents PCS 3rd Octet represents External DS1 4th Octet represents Internal DS1 5th and 6th Octets are reserved for future Internal DS1. For OP-108/106 cards of LRS-102 and MP-4100 notPresent interfaces may be: - External DS1 when its 'associated' Int-DS1 port is connected to another card - Internal DS1 when its 'associated' Ext-DS1 port is connected to another card (Both may be 'present' when inter-connected). 1st Octet represents External DS1 2nd Octet represents Internal DS1 Bit representation, same as for ASMi-54C card.
OCT mdlCmprObj	1.3.6.1.4.1.164.3.1.3.3.1.1.5	OCTET STRING	read-write	This attribute is the compressed information itself.
OCT mdlPbxFraSignalMask	1.3.6.1.4.1.164.3.2.2.1.1.1.1.7	OCTET STRING	read-write	In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the 'don't care' A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote.
OCT mdlPbxFraSignalVector	1.3.6.1.4.1.164.3.2.2.1.1.1.1.6	OCTET STRING	read-write	In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote In conjunction with the Mask, mdlPbxFraSignalMask, it is possible to compute the signal mode.
OCT mngAlarmTrapMask	1.3.6.1.4.1.164.6.2.7.1.5	OCTET STRING	read-write	The value of this object determines the alarm traps that the agent should mask (not send to this manager). The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. For more details on the specific alarm traps masked, see product specification.
OCT modlParamLeds	1.3.6.1.4.1.164.6.2.32.1.1.1.4	OCTET STRING	read-only	This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
OCT prtAlarmsCmprObj	1.3.6.1.4.1.164.3.1.4.3.3.1.5	OCTET STRING	read-only	This attribute is the compressed information itself.
OCT prtAlrMask	1.3.6.1.4.1.164.3.3.3.1.4.2.1.2	OCTET STRING	read-write	This object is a mask that indicates which port level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the port level will be 0. This object is applicable only when prtGenAlrMaskAll=off (otherwise all port alarms are masked). Example: When Alarms having the codes 31 and 40 are masked, the value of this object will be 10080000000 (hex).
OCT prtBertTs	1.3.6.1.4.1.164.3.3.3.1.5.1.12	OCTET STRING	read-write	This object indicates on which TSs of the selected port, BERT should be applied. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - BERT should be applied on this TS. For a T1 port, the valid raised bits ('1') are: 1..25. For an E1 port, the valid raised bits ('1') are: 1..31. Agents that do not support this feature will send SIZE 0.
OCT prtCmprObj	1.3.6.1.4.1.164.3.1.4.3.1.1.6	OCTET STRING	read-write	This attribute is the compressed information itself.
OCT prtCmprStatisticObj	1.3.6.1.4.1.164.3.1.4.3.1.1.7	OCTET STRING	read-only	This attribute is the compressed statistics information itself.
OCT prtDlciCmprObj	1.3.6.1.4.1.164.3.1.4.3.2.1.6	OCTET STRING	read-write	This attribute is the compressed information itself.
OCT prtDs3CurrentStatus	1.3.6.1.4.1.164.3.1.6.3.1.2.1.19	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
OCT prtDs3IntervalStatus	1.3.6.1.4.1.164.3.1.6.3.1.3.1.20	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
OCT prtExTsRxIoSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.12	OCTET STRING	read-only	IO - Rx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is received from IO port for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExTsRxSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.10	OCTET STRING	read-only	Link - Rx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is received from Link for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExTsTxIoSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.11	OCTET STRING	read-only	IO - Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is sent to IO port for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExTsTxSignaling	1.3.6.1.4.1.164.3.1.4.2.1.1.9	OCTET STRING	read-only	Link - Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is sent to Link for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
OCT prtExVc2RxBitOutput	1.3.6.1.4.1.164.3.2.3.2.5.1.21	OCTET STRING	read-write	- - - For MP (VC-Q card only) & FCD - - - This object represents 3 parameters by 2 Octets: Spare -MSB nibble, always=0 hex E Lead Output - nibble, Reverse Polarity Output- nibble, Metering Pulse Output -LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = Rx A bit 2 hex = 0010 = Rx A bit inverse 3 hex = 0011 = Rx B bit 4 hex = 0100 = Rx B bit inverse 5 hex = 0101 = Rx C bit 6 hex = 0110 = Rx C bit inverse 7 hex = 0111 = Rx D bit 8 hex = 1000 = Rx D bit inverse 9 hex = 1001 = none A-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For MP (VC-8, VC-16, VC-16A cards) - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = not used (invalid value) 2 hex = 0010 = not used (invalid value) 3 hex = 0011 = not used (invalid value) 4 hex = 0100 = not used (invalid value) 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO. - - - For WR II - - - This object represents the following 2 parameters in 1 Octet: 1. On/Off hook signaling receive mode from the T1/E1 into the FXS/FXO (MSB nibble 1). 2. E (Ear) Signaling receive mode from the T1/E1 into the E&M (LSB nibble 2). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook E (Ear) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable 1 hex = 0001 Rx A bit Rx A bit 2 hex = 0010 Rx A bit inverse Rx A bit inverse 3 hex = 0011 Rx B bit Rx B bit 4 hex = 0100 Rx B bit inverse Rx B bit inverse 5-F hex not used-invalid not Used-invalid Default value: 11
OCT prtExVc2TxBitCode	1.3.6.1.4.1.164.3.2.3.2.5.1.20	OCTET STRING	read-write	- - - For MP & FCD - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = M lead 2 hex = 0010 = M lead inverse 3 hex = 0011 = Reverse Polarity 4 hex = 0100 = Metering Pulse 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For WR II - - - This object represents the following 4 parameters by 2 Octets: 1. On/Off hook signaling transmission mode from the FXS towards the T1/E1 (MSB nibble 1). 2. Default signaling bits that are not in use (nibble 2). 3. Ring Detection signaling transmission mode from the FXO towards the T1/E1(nibble 3). 4. M (Mouth) Signaling transmission mode from the E&M towards the T1/E1(LSB nibble 4). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook Default sig. Ring Detect. M (Mouth) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable. Not Applicable Not Applicable 1 hex = 0001 Tx A bit Values 1-3 are Tx A bit Tx A bit 2 hex = 0010 Tx A bit inverse for On/Off Hook Tx A bit inv. Tx A bit inv. 3 hex = 0011 Tx B bit A,B,A Inv,B Inv. Tx B bit Tx B bit 4 hex = 0100 Tx B bit inverse Values 4-7 are Tx B bit inv. Tx B bit inv. 5 hex = 0101 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid 6 hex = 0110 not Used-invalid A, A Inverse. not Used-invalid not Used-invalid 7 hex = 0111 not Used-invalid not Used-invalid not Used-invalid 8 hex = 1000 not Used-invalid Values 8-11 are not Used-invalid not Used-invalid 9 hex = 1001 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid A hex = 1010 not used-invalid B, B Inverse. not Used-invalid not Used-invalid B hex = 1011 not used-invalid The Bits order: not Used-invalid not Used-invalid C-F hex not used-invalid ABCD not Used-invalid not Used-invalid Default value: 11 11
OCT prtFrPlusNotSegmentedPriorities	1.3.6.1.4.1.164.3.2.3.2.18.1.1.4	OCTET STRING	read-write	This parameter is relevant only for FR+ protocol and asks the MXcess NOT to segment data with specified priorities: from LSB: bit 1 is for priority 1, bit 2 is for priority 2, .... till bit 7 for priority 7. - a priority selected to be segmented : its bit will be '0' - a priority not to be segmented : its bit will be '1' Default is 00000000; i.e, segment all priorities.
OCT prtGenParamStatus	1.3.6.1.4.1.164.3.3.3.1.1.1.15	OCTET STRING	read-only	This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For HS cards (Dxc cards) - 1 octet: Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 0 and 1 indicates RTS control signal state: Bit 1: '1'=active ; '0'=notActive Bit 0 (LSB): '1'=unknown ; '0'=NA - For HS-U/1 external port (MP card, used in FCD-M) - 1 Octet: Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For VC-6, VC-12, VC-12/6 external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 \|___\| \|_______\| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=Unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|___________\| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For KM2100, KVF.5 cards - indicates the status of A and B signaling for each internal channel. 1 Octet: Bit - 7 6 5 4 3 2 1 0 \|_____\| \|_\| \|_\| spare B A Bit 0 (LSB) and Bit 1 : A status Bit 2 and Bit 3 : B status 00 - Off 01 - On 11 - Unknown - For FCD-W, NETWORK and USER ports - 1 Octet Status of Control Signals: '1'=On ; '0'=Off or when not applicable Bit - 7 6 5 4 3 2 1 0 Bit 7 (MSB) - Signal Loss (applicable only for G.703 interface) Bit 6 - CONTROL (applicable only for X.21 interface) Bit 5 - INDICATION (applicable only for X.21 interface) Bit 4 - DSR (applicable only for V.35 interface) Bit 3 - RTS (applicable only for V.35 interface) Bit 2 - CTS (applicable only for V.35 interface) Bit 1 - DTR (applicable only for V.35 interface) Bit 0 - DCD (applicable only for V.35 interface) - For DXC R6 , D8U, D16U External ports - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For DXC DE1-HDSL, DT1-HDSL, D16GSDSL, D8SL External ports - 2 Octets MSB octet: far-end modem channel interface LSB octet: Sub Link existence (Y/N), far-end modem type, synchronization with far-end modem MSB octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) 0000 1011 = IR-ETH-QN Rest of the combinations: reserved LSB octet: Bit 7 6 5 4 3 2 1 0 LSB \| \|___________\| \|__\| SL modem sync or Box material SL: modem: 00000 = other sync: 00 = not sync 0=not exist 00001 = unknown 01 = sync 1=exists 00010 = ASMi-31/2 10 = reserved 00011 = HCD-E1 11 = reserved Box material 00100 = HTU-E1 (for D8SL card): 00101 = HTU-2 0=metal 00110 = ASMi-52 SA/2W/Slave 1=plastic 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD 01110 = D8GSDSL card of DXC-3000 01111 = ASMi-52A Rest = reserved
OCT prtGenTestCmdXP	1.3.6.1.4.1.164.3.3.3.1.1.1.18	OCTET STRING	read-write	This is an Expanded test command of the prtGenTestCmd object. The prtGenTestCmd object reached its maximum, being an Integer with 31 bits. Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMaskXP). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the requested value is 00000003 hex -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system.
OCT prtGenTestMaskXP	1.3.6.1.4.1.164.3.3.3.1.1.1.17	OCTET STRING	read-only	This is an Expanded test mask of the prtGenTestMask object. The prtGenTestMask object reached its maximum, being an Integer with 31 bits. This object indicates which tests from the 'prtGenTestCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
OCT prtGenTestRunningXP	1.3.6.1.4.1.164.3.3.3.1.1.1.19	OCTET STRING	read-only	This is an Expanded object of the prtGenTestRunning object. The prtGenTestRunning object reached its maximum, being an Integer with 31 bits. This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only!
OCT prtMl4DataOos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.8	OCTET STRING	read-write	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT prtMl4VoiceOos	1.3.6.1.4.1.164.3.2.3.2.19.1.1.7	OCTET STRING	read-write	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT prtMonitoredTSs	1.3.6.1.4.1.164.3.3.3.1.6.1.6	OCTET STRING	read-write	This object indicates which TSs of the Monitored port, should be monitored. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled.
OCT prtMonitoringTSs	1.3.6.1.4.1.164.3.3.3.1.6.1.4	OCTET STRING	read-write	This object indicates which TSs of the Monitoring port, the test equipment should monitor. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled.
OCT prtParamActUponLoopDetect	1.3.6.1.4.1.164.6.2.15.5.1.1.21	OCTET STRING	read-write	This parameter is used to indicate which actions should be taken in case a loop is detected in the network the port is part of. Each action is represented by a bit. Currently defined (for RIC155GE/RIC622GE): Bit 0 - Transmit Shut Down Bit 1 - Forward Alarms If bit value = '1' then the action is taken. If bit value = '0' then the actions is not taken.
OCT prtParamClkQualityLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.14	OCTET STRING	read-only	This parameter indicates quality level of clock signal. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows (when bit1=0): Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit)- Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization) 0001 PRS (=ST1 = Stratum 1 Traceable) 0111 ST2 (Stratum 2 Traceable) 1010 ST3 (Stratum 3 Traceable) 1100 SMC (SONET Minimum Clock Traceable) 1101 Stratum 3E Traceable bit1 = '1' - indicates all octet is Not Applicable
OCT prtParamClkUserQualityLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.18	OCTET STRING	read-write	This parameter allows user to mark quality level of clock. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows: Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit) Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization)
OCT prtParamLeds	1.3.6.1.4.1.164.6.2.15.5.1.1.9	OCTET STRING	read-only	This entry specifies the LEDs status of the port. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
OCT prtPhyCurrentStatus	1.3.6.1.4.1.164.3.1.6.8.2.1.1.6	OCTET STRING	read-only	The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
OCT prtPhyIntervalStatus	1.3.6.1.4.1.164.3.1.6.8.2.2.1.7	OCTET STRING	read-only	The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
OCT prtSParamStatus	1.3.6.1.4.1.164.3.1.4.1.1.1.15	OCTET STRING	read-only	This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For VC-6, VC-6A, VC-6AG, VC-6A/4LB, VC-12, VC-12/6, external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 \|___\| \|_______\| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|___________\| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For ACM external port - 1 Octet Bit - 7 6 5 4 3 2 1 0 \|_________\| spare Alarm State Alarm State: according to bits 1,0: 00=NA ; 01=unused ; 10=Off ; 11=On - For HS-U/1 external port - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB \|________\| \|__\| \|__\| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For MTML-2/4 external ports, ML-8 externalports, ML-IP (MTML-IP) internal ports and MTML-E2 internal ports - 1 Octet : Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) - For ML-20N external ports - 4 Octets - 1 MS Octet will represent the Actual Link Rate: Bit - 7 6 5 4 3 2 1 0 \|_\| \|_________\| spare Rate Valid values: 0..34, meaning: 0..32 = (0..32)x64Kbps 33 = Invalid Rate 34 = not applicable (when Rate is not Auto) 35 = 0 Kbps Invalid values: 36..255. - 2 middle Octets will represent the Status of 4 Control Signals: - LS Octet - Bits 3-0: RTS/C (Command, for X.21 interface) Bits 7-4: DCD/I (Indication for X.21 interface) - MS Octet - Bits 3-0: DTR Bits 7-4: DSR Each 4 Bits are divided as follows: - 2 MS bits: DCE - 2 LS bits: DTE For each 2 bits (DCE/DTE): 00=NA ; 01=unused ; 10=Off ; 11=On. - LS Octet: (as for MTML-2): Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) - For MP-2100/2200 MSL-4/E1, MSL-8/E1 External ports - 3 Octets - MS octet: far-end modem channel interface - Middle octet: Material (plastic/metal), far-end modem type, synchronization with far-end modem - LS octet: BERT state (at port/TS/Bit level) - MS octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) 0000 1011 = IR-ETH-QN Rest of the combinations: reserved - Middle octet: Bit 7 6 5 4 3 2 1 0 LSB \| \|___________\| \|__\| Box material modem sync Box material modem: 00000 = other sync: 00 = not sync (for ASMi-52 SA) 00001 = unknown 01 = sync 0=metal 00010 = reserved 10 = reserved 1=plastic 00011 = reserved 11 = reserved 00100 = reserved 00101 = reserved 00110 = ASMi-52 SA/2W/Slave 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD-IP 01101 = FCD-IPM 01110 = D8SL card of DXC-30 01111 = ASMi-52A 10000 = MP card (SHDSL) 10001 = ASMi-52L Rest = reserved - LS Octet: (as for MTML-2): Bit 7 6 5 4 3 2 1 0 LSB \| BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs) 1 = ON (BERT is running on this port OR on one of its TSs) - For MP-4100 MSL card Links - 4 Octets - MS octet: far-end modem DTE2 interface (same as for MP-2100 MSL cards) - after MS octet: far-end modem DTE1 interface (same as for MP-2100 MSL cards) - before LS octet: Material (plastic/metal), far-end modem type, synchronization with far-end modem (same as for MP-2100 MSL cards) - LS octet: BERT state (at port/TS/Bit level)- same as for MP-2100 MSL cards - For MP-4100, LRS-102 OP-108/106 Links - 3 Octets - MS octet: far-end PS type and state - Middle octet: synchronization with far-end device - LS octet: BERT state (at port/TS level) - same as for MP-2100 MSL cards - MS octet: Bit 7 6 5 4 3 2 1 0 LSB \|__\| \|__\| \|__\| \|__\| PS-A PS-A PS-B PS-B PS Type PS State PS Type PS State 00=None 00=None 01=AC-DC 01=OK 10=DC 10=Fail - Middle octet: Bit 7 6 5 4 3 2 1 0 LSB \|__\| sync: 00 = not sync 01 = sync 10 = reserved 11 = reserved Rest = reserved
OCT prtSpCmd	1.3.6.1.4.1.164.3.3.3.4.1.1.19	OCTET STRING	read-write	SP Command. For LRS this parameter will be used for a Modem Command. Upon NMS's Get operation for devices that this parameter is notApplicable, agent will send NULL string.
OCT prtSTestMaskXp	1.3.6.1.4.1.164.3.1.4.1.1.1.16	OCTET STRING	read-write	This is an Expanded test mask of the prtSTestMask object. The prtSTestMask object reached its maximum, being an Integer with 32 bits. This object indicates which tests from the 'prtSTstCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 csuLoopAndBert 32 dsuLoopAndBert 33 remoteOcuLoopAndBert 34 remoteCsuLoopAndBert 35 remoteDsuLoopAndBert 36 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
OCT prtT1E1DataOos	1.3.6.1.4.1.164.3.3.3.2.2.1.14	OCTET STRING	read-write	Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT prtT1E1FdlMsg	1.3.6.1.4.1.164.3.3.3.2.3.1.4	OCTET STRING	read-only	FDL message.
OCT prtT1E1IdleCode	1.3.6.1.4.1.164.3.3.3.2.2.1.11	OCTET STRING	read-write	This object selects the code transmitted to fill idle (unused) time slots in the main link frame. Valid range: (0 - FF HEX) .
OCT prtT1E1TS0SaBits	1.3.6.1.4.1.164.3.3.3.2.2.1.26	OCTET STRING	read-write	This object is applicable only for E1 ports. For T1, string size will be 0. For E1, it enables user to select the use of TS0 Sa Bits 4..8, by 3 octets: The order (in hexa display): free Sa-Bit-4 Sa-Bit-5 Sa-Bit-6 Sa-Bit-7 Sa-Bit-8 \|___________\| \|________________\| \|________________\| MSByte LSByte Each Sa Bit will be represented by a nibble, having the following meaning: 0000 = zero 0001 = one 0010 = management 0011 = transparent the rest are reserved for future use.
OCT prtT1E1VoiceOos	1.3.6.1.4.1.164.3.3.3.2.2.1.13	OCTET STRING	read-write	Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
OCT prtT1FdlMsg	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.4	OCTET STRING	read-only	FDL message.
OCT qProfileInternalQProfile	1.3.6.1.4.1.164.6.3.11.1.1.5	OCTET STRING	read-create	This attribute holds the indexes to the queue profiles in the qInternalProfileTable. Each couple of octets holds an index to the qInternalProfileTable.
OCT radBridgeCODTrafficTriggerProtType	1.3.6.1.4.1.164.4.1.4.3.4	OCTET STRING	read-write	Protocol Type for the User Defined Protocol Traffic Trigger (3).
OCT radBridgeIPXRipDestNetwork	1.3.6.1.4.1.164.4.1.5.2.6.1.1	OCTET STRING	read-only	The destination network address to which this entry's routing information pertains.
OCT radBridgeIPXRipForwardingRouter	1.3.6.1.4.1.164.4.1.5.2.6.1.3	OCTET STRING	read-write	The IPX node address of the next hop (router) for the entry's associated destination network.
OCT radBridgeIPXSapNetwork	1.3.6.1.4.1.164.4.1.5.3.6.1.3	OCTET STRING	read-write	The IPX network address of the host on which this server exists.
OCT radBridgeIPXSapNode	1.3.6.1.4.1.164.4.1.5.3.6.1.4	OCTET STRING	read-write	The IPX node address of the host on which this server exists.
OCT radBridgeMaskActiveBit1	1.3.6.1.4.1.164.4.1.3.1.6	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat1 field.
OCT radBridgeMaskActiveBit2	1.3.6.1.4.1.164.4.1.3.1.11	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat2 field.
OCT radBridgeMaskActiveBit3	1.3.6.1.4.1.164.4.1.3.1.16	OCTET STRING	read-write	Specifies the positions of the wild card characters (*) in the radBridgeMaskPat3 field.
OCT radBridgeMaskPat1	1.3.6.1.4.1.164.4.1.3.1.5	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
OCT radBridgeMaskPat2	1.3.6.1.4.1.164.4.1.3.1.10	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
OCT radBridgeMaskPat3	1.3.6.1.4.1.164.4.1.3.1.15	OCTET STRING	read-write	Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
OCT radMdName	1.3.6.1.4.1.164.3.1.6.1.3.3.1.3	OCTET STRING	read-create	The Maintenance Domain name. The type/format of this object is determined by the value of the radMdNameType object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain.
OCT radMepLtrEgressPortId	1.3.6.1.4.1.164.3.1.6.1.3.4.1.10	OCTET STRING	read-only	Egress Port ID. The format of this object is determined by the value of the radMepLtrEgressPortIdSubtype object. If the radMepLtrEgress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:r and 20.36.2.13
OCT radMepLtrIngressPortId	1.3.6.1.4.1.164.3.1.6.1.3.4.1.7	OCTET STRING	read-only	Ingress Port ID. This is an alpha-numeric string that contains a specific identifier for the port. The format of this object is determined by the value of the radMepLtrIngressPortIdSubtype object. If the radMepLtrIngress object contains the value ingNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:n and 20.36.2.9
OCT radMepMaName	1.3.6.1.4.1.164.3.1.6.1.3.1.1.17	OCTET STRING	read-create	The Short Maintenance Association name.
OCT sysDclChPriority	1.3.6.1.4.1.164.3.3.1.2.2.1.1.7	OCTET STRING	read-write	This object indicates the Priority for all the channels in the Main Access (Common Logic) card. Each channel is represented by 1 bit. The order of the bits in each byte is from Right to Left (LSB Bit to MSB) starting from BIT 0: 7 6 5 4 3 2 1 0 Channel no. 1 is represented by bit 0. Channel no. 2 is represented by bit 1. Channel no. n is represented by bit n-1. The value of the bit shows the priority. For bit value = 1, Priority = High. For bit value = 0, Priority = Low.
OCT sysSAlrMask	1.3.6.1.4.1.164.3.3.1.4.5	OCTET STRING	read-write	This object is a mask that indicates which system level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the system level will be 0. This object is applicable only when sysSAlrMaskAll=off (otherwise all system alarms are masked). Example: When Alarms having the codes 6 and 11 are masked, the value of this object will be 840 (hex).
OCT systemOamDescrLoopbackDestAddr	1.3.6.1.4.1.164.6.2.36.2.1.6	OCTET STRING	read-create	Loopback Destination Address.
OCT tftpError	1.3.6.1.4.1.164.6.2.12.7	OCTET STRING	read-only	The MSB represents the standard error code. The LSB represents the private error code. 0x0000 is No Error 0x0100 is File Not Found 0x0200 is Access violation 0x0300 is Disk full or allocation exceeded 0x0400 is Illegal TFTP operation 0x0500 is Unknown transfer ID 0x0600 is File already exists 0x0700 is No such user 0x0001 is Server Overflow 0x0002 is No empty UDP port 0x0003 is No empty connection 0x0004 is Illegal File Mode 0x0007 is Illegal PDU size 0x0008 is TFTP Server does not exist 0x0009 is Incorrect File 0x000A is Wrong License format 0x000B is License ID already used
PerfCurrentCount (18)
PER dsx1CurrentAIS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.4	PerfCurrentCount	read-only	The counter associated with the number of AIS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentBPV	1.3.6.1.4.1.164.3.1.6.4.1.2.1.9	PerfCurrentCount	read-only	The counter associated with the number of BPVs (Bi-Polar Violations) encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentCRCErrors	1.3.6.1.4.1.164.3.1.6.4.1.2.1.12	PerfCurrentCount	read-only	Counts the number of CRC error events, encountered in the current 15 minute interval.
PER dsx1CurrentFEBE	1.3.6.1.4.1.164.3.1.6.4.1.2.1.7	PerfCurrentCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in the current 15 minute interval.
PER dsx1CurrentLOC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.3	PerfCurrentCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
PER dsx1CurrentLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.10	PerfCurrentCount	read-only	Loss of CRC4 Multi-Frame sequence in E1. encountered in the current 15 minute interval
PER dsx1CurrentLOF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.2	PerfCurrentCount	read-only	The counter associated with the number of LOF seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOFC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.11	PerfCurrentCount	read-only	Counts the number of loss of frame events measured. encountered in the current 15 minute interval
PER dsx1CurrentLOMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.6	PerfCurrentCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
PER dsx1CurrentLOS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.1	PerfCurrentCount	read-only	The counter associated with the number of LOS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentRAI	1.3.6.1.4.1.164.3.1.6.4.1.2.1.5	PerfCurrentCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
PER ethOamSvcCurrFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.1	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay greater than the threshold value defined for the service.
PER ethOamSvcCurrFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.3	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay variation greater than the threshold value defined for the service.
PER ethOamSvcCurrFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.2	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay lower than or equal to the threshold value defined for the service.
PER ethOamSvcCurrFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.4	PerfCurrentCount	read-only	Number of frames that arrived in the current interval at a delay variation lower than or equal to the threshold value defined for the service.
PER ethOamSvcCurrFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.6	PerfCurrentCount	read-only	Number of lost frames in the current interval.
PER ethOamSvcCurrFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.5	PerfCurrentCount	read-only	Number of trnasmitted frames in the current interval.
PER ethOamSvcCurrUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.13	PerfCurrentCount	read-only	The number of seconds that the service was unavailable in the current interval.
PerfIntervalCount (17)
NUM dsx1IntervalAIS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.4	PerfIntervalCount	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalBPV	1.3.6.1.4.1.164.3.1.6.4.1.3.1.9	PerfIntervalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalFEBE	1.3.6.1.4.1.164.3.1.6.4.1.3.1.7	PerfIntervalCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in one of the previous 96, individual, 15 minute intervals.
NUM dsx1IntervalLOC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.3	PerfIntervalCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
NUM dsx1IntervalLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.10	PerfIntervalCount	read-only	Loss of CRC4 Multi-Frame sequence in E1.
NUM dsx1IntervalLOF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.2	PerfIntervalCount	read-only	The counter associated with the number of OOF seconds, encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.11	PerfIntervalCount	read-only	Counts the number of loss of frame events measured in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.6	PerfIntervalCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
NUM dsx1IntervalLOS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.1	PerfIntervalCount	read-only	The counter associated with the number of LOS seconds , encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalRAI	1.3.6.1.4.1.164.3.1.6.4.1.3.1.5	PerfIntervalCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
NUM ethOamSvcIntervalFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.2	PerfIntervalCount	read-only	Number of frames that arrived in a delay greater than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.4	PerfIntervalCount	read-only	Number of frames that arrived in a delay variation greater than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.3	PerfIntervalCount	read-only	Number of frames that arrived in a delay lower than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.5	PerfIntervalCount	read-only	Number of frames that arrived in a delay variation lower than the threshold value defined for the service in the selected interval.
NUM ethOamSvcIntervalFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.7	PerfIntervalCount	read-only	Number of lost frames in the selected interval.
NUM ethOamSvcIntervalFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.6	PerfIntervalCount	read-only	Number of trnasmitted frames in the selected interval.
NUM ethOamSvcIntervalUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.13	PerfIntervalCount	read-only	The number of seconds that the service was unavailable in the selected interval.
PerfTotalCount (10)
PER dsx1TotalBPV	1.3.6.1.4.1.164.3.1.6.4.1.4.1.9	PerfTotalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.4.1.11	PerfTotalCount	read-only	The counter associated with the number loss of frames encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOS	1.3.6.1.4.1.164.3.1.6.4.1.4.1.1	PerfTotalCount	read-only	The counter associated with the number of LOS (Loss of Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER ethOamSvcTotalFramesAboveDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.1	PerfTotalCount	read-only	Number of frames that arrived in a delay greater than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesAboveDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.3	PerfTotalCount	read-only	Number of frames that arrived in a delay variation greater than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesBelowDelayThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.2	PerfTotalCount	read-only	Number of frames that arrived in a delay lower than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesBelowDVarThresh	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.4	PerfTotalCount	read-only	Number of frames that arrived in a delay variation lower than the threshold value defined for the service in the last 24H.
PER ethOamSvcTotalFramesLossCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.6	PerfTotalCount	read-only	Number of lost frames in the last 24H.
PER ethOamSvcTotalFramesTxCounter	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.5	PerfTotalCount	read-only	Number of trnasmitted frames in the last 24H.
PER ethOamSvcTotalUnavailSec	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.12	PerfTotalCount	read-only	The number of seconds that the service was unavailable in the last 24H.
PortList (6)
POR ethIfRingPorts	1.3.6.1.4.1.164.3.1.6.1.4.1.1.3	PortList	read-write	The set of ports which are assigned to be ring members. The default value of this object is a string of zeros.
POR lagPortMembers	1.3.6.1.4.1.164.6.2.54.1.1.3	PortList	read-create	The set of ports which are permanently assigned to the Link Aggregation Group. The default value of this object is a string of zeros.
POR radBridgeDot1qVlanTaggedPorts	1.3.6.1.4.1.164.4.1.9.2.1.1	PortList	read-create	The set of ports which should transmit egress packets for this VLAN as tagged.
POR radBridgeDot1qVlanUnmodifiedPorts	1.3.6.1.4.1.164.4.1.9.2.1.2	PortList	read-create	The set of ports which should transmit egress packets for this VLAN as unmodified.
POR radBridgePortBaseVlanEgressPorts	1.3.6.1.4.1.164.4.1.8.1.1.4	PortList	read-create	The set of ports which are permanently assigned to the egress list for this port based VLAN by management. The default value of this object is a string of zeros.
POR radBridgePortBaseVlanVirtualGroups	1.3.6.1.4.1.164.4.1.8.1.1.5	PortList	read-create	The set of Virtual Groups which are permanently assigned to this port based VLAN by management. (read Virtual Group instead of port in PortList Textual Convention) The default value of this object is a string of zeros.
RowPointer (1)
NUM ifCreateConnectionPointer	1.3.6.1.4.1.164.6.2.35.1.1.9	RowPointer	read-create	This parameter represents the entity that is connected to this Interface. It can be used instead of ifCreateConnectedTo. It is an OBJECT IDENTIFIER. This parameter's SYNTAX allows the following possibilities: - can be simply used for entity that is not an interface - is not limited to include up to 32 bits The value of this parameter is a pointer to an existing row of a table, where the entity connected to this Interface is defined (i.e. the pointer uniquely identifies the connected entity). Examples: In case of an interface (from 2863.ifTable): points to 'ifEntry' of corresponding row = . In case of a VPI/VCI (from 2515.atmVclTable): points to 'atmVclEntry' of corresponding row = ..VPI.VCI In case no entity is connected, value = 0 .
RowStatus (45)
ROW agnClkSrcPortRowStatus	1.3.6.1.4.1.164.6.2.52.1.1.5	RowStatus	read-create	This object enables Creation/ Deletion of rows in the table.
ROW agnCT1E1RingRowStatus	1.3.6.1.4.1.164.3.1.2.2.10.1.7	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW agnDlciRowStatus	1.3.6.1.4.1.164.3.1.2.8.1.1.17	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set agnRowStatus.255.id2.id3.id4.id5.id6.id7 = active(1). For destroying a row, the NMS should set: agnRowStatus.255.id2.id3.id4.id5.id6.id7 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW agnGroupRowStatus	1.3.6.1.4.1.164.6.2.56.1.4	RowStatus	read-create	This object enables user to create/delete entries of this table. destroy - If a Group is used in another table, Agent may not allow destroying the entry/ies that belong to this Group Index.
ROW agnVoiceSwConfRtRowStatus	1.3.6.1.4.1.164.3.1.2.9.2.1.9	RowStatus	read-create	Status of the row for creating/deleting entries in the table. The only possible supported RowStatus vaules are active (1), notInService (2), notReady(3), createAndGo(4), createAndWait(5) and destroy(6).
ROW alarmForwardingRowStatus	1.3.6.1.4.1.164.6.2.50.1.3	RowStatus	read-create	Creation/ Deletion of rows in the table.
ROW atmAlarmForwardingRowStatus	1.3.6.1.4.1.164.12.3.1.1.32.1.3	RowStatus	read-create	Creation/Deletion of rows in the table.
ROW atmNteHostRowStatus	1.3.6.1.4.1.164.12.3.1.1.11.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
ROW atmNteManagerRowStatus	1.3.6.1.4.1.164.12.3.1.1.1.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
ROW atmVcPmRowStatus	1.3.6.1.4.1.164.12.3.2.3.2.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
ROW atmVpPmRowStatus	1.3.6.1.4.1.164.12.3.2.3.1.1.6	RowStatus	read-create	Creation/Deletion of rows in the table.
ROW cosProfileRowStatus	1.3.6.1.4.1.164.6.3.10.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
ROW dhcpIfClientRowStatus	1.3.6.1.4.1.164.11.7.2.2.1.7.1.3	RowStatus	read-create	The row status used for creating, modifying, and deleting instances of the columnar objects in the dhcpIfClientTable. For Vmux Devices, it will be possible only to Delete instances. The addition of Clients will be done automatically by the Server according to Network messages that are sent by the Clients; not via SNMP. In order to Delete a Client, this MIB object should be set to: destroy (6).
ROW dot3OamDescrRowStatus	1.3.6.1.4.1.164.3.1.6.1.6.1.1.2	RowStatus	read-create	This object controls creation/deletion of the associated entry in this table per the semantics of RowStatus. If an active entry is referenced in dot3OamXDescrId, the entry MUST remain active until all references are removed.
ROW ethOamServiceRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.2	RowStatus	read-create	This attribute allows to create/delete a row in this table.
ROW evcCosRowStatus	1.3.6.1.4.1.164.6.3.7.1.3	RowStatus	read-create	This attribute allows to create/delete a row in this table.
ROW flowMappingProfileRowStatus	1.3.6.1.4.1.164.6.3.9.1.1.3	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
ROW hostRowStatus	1.3.6.1.4.1.164.6.2.40.1.9	RowStatus	read-create	Creation/Deletion of rows in the table.
ROW ifCreateRowStatus	1.3.6.1.4.1.164.6.2.35.1.1.4	RowStatus	read-create	This object enables the user to create/delete entries in this table.
ROW ip2IfRowStatus	1.3.6.1.4.1.164.3.1.6.7.1.1.2	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table.
ROW lagRowStatus	1.3.6.1.4.1.164.6.2.54.1.1.7	RowStatus	read-create	This object enables user to create/delete entries of this table. Note: When using LAG standard package, this table is static, hence, only the values active(1), notInService(2) are used.
ROW markingProfileRowStatus	1.3.6.1.4.1.164.6.3.12.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
ROW mdlProtIpRowStatus	1.3.6.1.4.1.164.3.2.2.1.2.1.4	RowStatus	read-create	This parameter allows creating/deleting entries of this table.
ROW prtBdbandRowStatus	1.3.6.1.4.1.164.3.1.6.8.1.1.1.6	RowStatus	read-create	Creation/Deletion of rows in the table.
ROW prtIsdnDirectoryRowStatus	1.3.6.1.4.1.164.3.2.3.2.16.3.1.10	RowStatus	read-create	This is the status for the row. It allows to know whether to consider this row or not. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW prtIsdnEndpointRowStatus	1.3.6.1.4.1.164.3.2.3.2.16.2.1.9	RowStatus	read-create	This field indicates whether to consider this endpoint or not. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW prtLogicalRowStatus	1.3.6.1.4.1.164.3.2.3.2.17.1.1.6	RowStatus	read-create	This parameter allows the NMS to create/delete logical ports. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW qInternalProfileRowStatus	1.3.6.1.4.1.164.6.3.11.2.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
ROW qosFlowMappingRowStatus	1.3.6.1.4.1.164.6.3.9.2.1.4	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
ROW qProfileRowStatus	1.3.6.1.4.1.164.6.3.11.1.1.2	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
ROW queueGroupRowStatus	1.3.6.1.4.1.164.6.3.11.3.1.4	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
ROW radBridgeGenFlowRowStatus	1.3.6.1.4.1.164.4.1.9.1.1.3	RowStatus	read-create	This object enable user to create/delete entries in this table.
ROW radBridgePortBaseVlanRowStatus	1.3.6.1.4.1.164.4.1.8.1.1.6	RowStatus	read-create	This object enable user to create/delete entries in this table.
ROW radBridgePortVlanMemberRowStatus	1.3.6.1.4.1.164.4.1.8.2.1.4	RowStatus	read-create	This object enables the user to create/delete entries in this table.
ROW radMdRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.3.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
ROW radMepRowStatus	1.3.6.1.4.1.164.3.1.6.1.3.1.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table.
ROW ripSapIfConfStatus	1.3.6.1.4.1.164.11.7.2.3.4.1.3	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set ripSapIfConfStatus.id1 = active(1). For destroying a row, the NMS should set: ripSapIfConfStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW serviceRowStatus	1.3.6.1.4.1.164.6.3.6.1.3	RowStatus	read-create	This attribute is used to create a new row or to delete an existing row in the table.
ROW sysCRdnRowStatus	1.3.6.1.4.1.164.3.3.1.6.3.1.10	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table. The possible supported RowStatus values are active (1) and destroy (6). For Vmux-2100 the supported values are: active (1), createAndGo (4) and destroy (6).
ROW systemOamDescrRowStatus	1.3.6.1.4.1.164.6.2.36.2.1.2	RowStatus	read-create	Enables the user to create/delete entries in this table.
ROW wfqRowStatus	1.3.6.1.4.1.164.6.3.1.1.1.5	RowStatus	read-create	This object enables Creation/Deletion of rows in the WFQ table. For FCD-155, rows are not created nor destroyed by user.
ROW wrDhcpRowStatus	1.3.6.1.4.1.164.11.7.2.2.1.2.1.8	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrDhcpRowStatus.id = active(1). For destroying a row, the NMS should set: wrDhcpStatus.id = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW wrIpRowStatus	1.3.6.1.4.1.164.11.7.2.4.1.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrIpRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrIpRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW wrSpoofingRowStatus	1.3.6.1.4.1.164.11.7.2.4.2.1.4	RowStatus	read-create	This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrSpoofingRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrSpoofingRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
ROW xcRowStatus	1.3.6.1.4.1.164.6.2.31.1.6	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table.
SnmpAdminString (25)
STR agnStringToIndexUserName	1.3.6.1.4.1.164.6.2.62.1.2	SnmpAdminString	not-accessible	This object indicates a unique name used by agnStringToIndexTableId, although it is not it's index.
STR agnVoiceSwConfHGExtString	1.3.6.1.4.1.164.3.1.2.9.5.1.5	SnmpAdminString	read-write	This is the extension string of the hunt group. This string is a combination of digits, * and #.
STR agnVoiceSwConfHGUserParams	1.3.6.1.4.1.164.3.1.2.9.5.1.6	SnmpAdminString	read-write	This object indicates the User's parameters.
STR atmVcCrossConnectName	1.3.6.1.4.1.164.12.3.1.1.35.1.1	SnmpAdminString	read-create	The Connection's name.
STR atmVpCrossConnectName	1.3.6.1.4.1.164.12.3.1.1.34.1.1	SnmpAdminString	read-create	The Connection's name.
STR autoFileTransferFileName	1.3.6.1.4.1.164.6.2.12.13.1.1.3	SnmpAdminString	read-write	This object defines the name of the file to be uploaded.
STR cosProfileName	1.3.6.1.4.1.164.6.3.10.1.4	SnmpAdminString	read-create	This attribute defines the name assigned to CoS profile.
STR evcCosEvcName	1.3.6.1.4.1.164.6.3.7.1.5	SnmpAdminString	read-create	A string that identifies the EVC. It should be unique in the Maintenance Domain (i.e., in the managed network) Used as MEG ID field in OAM messages.
STR flowMappingProfileName	1.3.6.1.4.1.164.6.3.9.1.1.6	SnmpAdminString	read-create	This attribute defines the name assigned to flowMappingIndex profile.
STR invNameXC	1.3.6.1.4.1.164.6.2.41.1.1	SnmpAdminString	not-accessible	The unique Connection name, associated to a Cross-Connection.
STR markingProfileName	1.3.6.1.4.1.164.6.3.12.1.3	SnmpAdminString	read-create	This attribute defines the unique name assigned to the Marking profile.
STR mdlSPiggybackVer	1.3.6.1.4.1.164.3.3.2.1.1.1.18	SnmpAdminString	read-only	This attribute indicates the Piggyback version of the card installed in the specific slot position.
STR physicalConnectorString	1.3.6.1.4.1.164.6.2.15.1.1.9	SnmpAdminString	read-only	(SFP) connector type. It can be Vendor Specific (unknown in advance). Being a string, the object is not affected by any future new connectors. This object will usually not be used for drawing the connector.
STR portMfgName	1.3.6.1.4.1.164.6.2.15.1.1.7	SnmpAdminString	read-only	(SFP) Port Manufacturer name (Maximum - 16 characters).
STR portVendorPartNo	1.3.6.1.4.1.164.6.2.15.1.1.10	SnmpAdminString	read-only	SFP Vendor Part Number. Being a string, the object is not affected by any future new SFPs.
STR qProfileName	1.3.6.1.4.1.164.6.3.11.1.1.3	SnmpAdminString	read-create	This attribute holds the name of the Queue cluster profile.
STR queueGroupName	1.3.6.1.4.1.164.6.3.11.3.1.1	SnmpAdminString	not-accessible	Defines the Queue Group unique name.
STR queueGroupPointToQBlock	1.3.6.1.4.1.164.6.3.11.3.1.7	SnmpAdminString	read-create	This attribute defines the Queue Block name of the next Queue Block level that is pointed by this Queue Block.
STR queueGroupQBlockName	1.3.6.1.4.1.164.6.3.11.3.1.9	SnmpAdminString	read-create	This attribute holds the name of the Queue Block.
STR radBridgePortBaseVlanName	1.3.6.1.4.1.164.4.1.8.1.1.3	SnmpAdminString	read-create	An administratively assigned string, which may be used to identify the the port based VLAN.
STR serviceName	1.3.6.1.4.1.164.6.3.6.1.4	SnmpAdminString	read-create	This attribute defines the service name.
STR sysBufferAlrInfo	1.3.6.1.4.1.164.3.3.1.5.1.1.9	SnmpAdminString	read-only	This parameter includes information about the alarm (additional to the Description).
STR sysCRdnName	1.3.6.1.4.1.164.3.3.1.6.3.1.22	SnmpAdminString	read-create	A textual name for the redundancy group.
STR wrDhcpConfigFileName	1.3.6.1.4.1.164.11.7.2.2.1.2.1.12	SnmpAdminString	read-create	TFTP-name of the configuration File Name for DHCP pool.
STR wrDhcpPoolName	1.3.6.1.4.1.164.11.7.2.2.1.2.1.10	SnmpAdminString	read-create	DHCP pool name - string with max length of 10 characters
SysIfEntityType (1)
SYS ifCreateEntityType	1.3.6.1.4.1.164.6.2.35.1.1.1	SysIfEntityType	read-only	This object indicates the Type of the Entity that exists above the created interface. For a Logical Port, this value can be: other (1) when there is no fixed entity above it.
Timeout (6)
TIM radBridgeStpCnfgForwardDelay	1.3.6.1.4.1.164.4.1.11.1.1.3	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for Forward Delay when this bridge is acting as the root. Note that the range for this parameter is related to the value of radBridgeStpCnfgMaxAge (according to 802.1D-1990 for the similar scalars of BRIDGE-MIB). The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM radBridgeStpCnfgHelloTime	1.3.6.1.4.1.164.4.1.11.1.1.5	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for Hello Time when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM radBridgeStpCnfgMaxAge	1.3.6.1.4.1.164.4.1.11.1.1.4	Timeout	read-write	The value that the bridge of radBridgeStpCnfgIdx2 uses for MaxAge when this bridge is acting as the root. Note that the range for this parameter is related to the value of radBridgeStpCnfgHelloTime (according to 802.1D-1990 for the similar scalars of BRIDGE-MIB). The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM radBridgeStpStatForwardDelay	1.3.6.1.4.1.164.4.1.11.2.1.2	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to radBridgeStpCnfgForwardDelay which is the value that this bridge would start using if/when this bridge were to become the root.]
TIM radBridgeStpStatHelloTime	1.3.6.1.4.1.164.4.1.11.2.1.4	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM radBridgeStpStatMaxAge	1.3.6.1.4.1.164.4.1.11.2.1.3	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TimeStamp (1)
TIM prtParamLastResetStatsTime	1.3.6.1.4.1.164.6.2.15.5.1.1.6	TimeStamp	read-only	The value of MIB II's sysUpTime object at the last time that prtParamResetStatsCmd was Set to on(3) for this port. If prtParamResetStatsCmd was never Set to on(3) since last re-initialization of the agent, then this object contains a zero value. This object enables calculating the running time of Statistics counters for this port, by: [sysUpTime-prtParamLastResetStatsTime]. For some devices other types of 'Reset' may affect this parameter
TimeTicks (5)
TIK prtPerfTimeTag	1.3.6.1.4.1.164.6.2.15.3.1.1.9	TimeTicks	read-only	Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was executed. This object is applicable only for prtPerfPeriodRef=lastPeriod. For prtPerfPeriodRef=currentPeriod, the value will always be 0.
TIK radBridgeIPXRipAgingTime	1.3.6.1.4.1.164.4.1.5.2.6.1.7	TimeTicks	read-only	The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.
TIK radBridgeIPXSapAgingTime	1.3.6.1.4.1.164.4.1.5.3.6.1.8	TimeTicks	read-only	The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.
TIK sysBufferAlrUpTime	1.3.6.1.4.1.164.3.3.1.5.1.1.8	TimeTicks	read-only	The time when the alarm occured. This parameter holds the sysUpTime value when the alarm occured.
TIK trapTimeSinceOccurrence	1.3.6.1.4.1.164.6.2.11.1.3	TimeTicks	read-only	This object indicates the amount of time passed since the occurrence of the event that triggered this trap.
TruthValue (1)
T/F dsx1DataStreamStatValid	1.3.6.1.4.1.164.3.1.6.4.1.5.1.3	TruthValue	read-only	Indicates whether this Data Stream is valid or not. When invalid - all counters are irrelevant.
Unsigned32 (188)
U32 agnCBuMlWaitToRestore	1.3.6.1.4.1.164.3.1.2.2.12.1.8	Unsigned32	read-write	This object defines traffic recovery time (in milliseconds) of the link after its recovery. This object is applicable only when Recovery Mode is revertive.
U32 agnClkCurrentIndex	1.3.6.1.4.1.164.6.2.52.3.1.1.1	Unsigned32	not-accessible	An Index that is uniquely represents the Clock.
U32 agnClkIntervalIndex	1.3.6.1.4.1.164.6.2.52.3.2.1.1	Unsigned32	not-accessible	An Index that is uniquely represents the Clock.
U32 agnClkIntervalNumber	1.3.6.1.4.1.164.6.2.52.3.2.1.2	Unsigned32	not-accessible	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
U32 agnCT1E1RingWTR	1.3.6.1.4.1.164.3.1.2.2.10.1.8	Unsigned32	read-create	T1/E1 Ring Wait to Restore (sec). Valid Values: 0..999, 65535. 65535=NA. When the value <> 65535, the value of agnCT1E1RingRecTime must be 65535.
U32 agnGroupCnfgIdx	1.3.6.1.4.1.164.6.2.56.1.1	Unsigned32	not-accessible	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 agnGroupComponentIdx	1.3.6.1.4.1.164.6.2.56.1.3	Unsigned32	not-accessible	This object indicates a unique Component Index that belongs to the Group defined by agnGroupIdx.
U32 agnGroupIdx	1.3.6.1.4.1.164.6.2.56.1.2	Unsigned32	not-accessible	This object indicates a unique Group Index.
U32 agnRowPointerNoOfUsages	1.3.6.1.4.1.164.6.2.63.1.2	Unsigned32	read-only	The number of usages of specific entry in a table, which is pointed by agnRowPointerIndex.Usually, when the value of this counter is greater than 0,the entry cannot be removed.
U32 agnStringToIndexTableIndex	1.3.6.1.4.1.164.6.2.62.1.3	Unsigned32	read-only	The numeric Index of agnStringToIndexTableId.
U32 agnSyslogDeviceUdpPort	1.3.6.1.4.1.164.6.2.58.1	Unsigned32	read-write	The UDP Port of the device, from which Syslog messages are sent. Default=514.
U32 agnTrapDelay	1.3.6.1.4.1.164.6.2.60	Unsigned32	read-write	This variable enables the user to set a delay (in seconds) before a trap is sent. This delay will be used only for traps that need to be sent during device initialization. It is needed because the device connected to our device starts transmitting traps later. The delay starts from the end of the Boot process. The device will keep the init traps in the correct order, and cancel those which clear former ones in the list. After this init delay, traps will be sent without a delay.
U32 alarmForwardingDelay	1.3.6.1.4.1.164.6.2.50.1.9	Unsigned32	read-create	This parameter determines the period of time (in seconds) the alarm of the alarmForwardingFailPort should exist before starting alarm forwarding.
U32 alrBufCode	1.3.6.1.4.1.164.3.1.2.4.1.1.3	Unsigned32	read-only	A code identifying the alarm of an entry in the alarm buffer table.
U32 alrBufIdxUponLastAck	1.3.6.1.4.1.164.3.1.2.4.3	Unsigned32	read-only	This attribute indicates the value of alrBufIdx for the last existing entry of alrBufTable, when alrBufferClearCmd was last Set to on(3). That will enable a user to see only Alarms that entered the alrBufTable after last Set of alrBufferClearCmd, by GetNext of alrBufDescription with this index.
U32 alrBufPort	1.3.6.1.4.1.164.3.1.2.4.1.1.5	Unsigned32	read-only	The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999.
U32 atmAlarmForwardingTimeFilterWindow	1.3.6.1.4.1.164.12.3.1.1.32.1.7	Unsigned32	read-create	This parameter determines the Time Filter Window, meaning: how much time (in seconds) should the alarm exist in order to start the Alarm Forwarding operation.
U32 cosProfileIndex	1.3.6.1.4.1.164.6.3.10.1.1	Unsigned32	not-accessible	Defines the CoS Profile ID.
U32 dot3OamDescrId	1.3.6.1.4.1.164.3.1.6.1.6.1.1.1	Unsigned32	not-accessible	This object is the unique index associated with this Descriptor (profile). Entries in this table are referenced via the object dot3OamXDescrId in dot3OamXEntry.
U32 dot3OamDescrRateLimit	1.3.6.1.4.1.164.3.1.6.1.6.1.1.5	Unsigned32	read-create	This object defines how many OAM frames can be sent per second (maximum) for an OAM EFM Link referencing this Descriptor.
U32 dot3OamXDescrId	1.3.6.1.4.1.164.3.1.6.1.6.2.1.1	Unsigned32	read-write	This object points to an entry of dot3OamDescrTable (dot3OamDescrId), which defines part of the configuration parameters for this OAM EFM Link. As long as one of the OAM EFM Links refers an entry in the dot3OamDescrTable, this entry cannot be removed. When an OAM EFM Link supports this object (RW), the standard MIB objects of: dot3OamMode (parallel to dot3OamDescrMode) and dot3OamLoopbackIgnoreRx (parallel to dot3OamDescrLbRxOperation) will be supported by Agent RO.
U32 dsx3MappingNumber	1.3.6.1.4.1.164.3.1.6.3.3.1.2	Unsigned32	not-accessible	The channel number for this entry. For RICi-16 this is the channel number 1...28.
U32 ethIfRingIdx	1.3.6.1.4.1.164.3.1.6.1.4.1.1.1	Unsigned32	not-accessible	This object is an Index that can indicate Slot, Ring, Cnfg etc., according to the device used. When NA, 1 will be used.
U32 ethIfRingKeepAliveInterval	1.3.6.1.4.1.164.3.1.6.1.4.1.1.5	Unsigned32	read-write	This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
U32 ethIfRingKeepAliveThresh	1.3.6.1.4.1.164.3.1.6.1.4.1.1.6	Unsigned32	read-write	This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
U32 ethIfRingKeepAliveVlanId	1.3.6.1.4.1.164.3.1.6.1.4.1.1.7	Unsigned32	read-write	Dedicated VLAN ID for keep alive messages.
U32 ethIfRingMultiCastVlanId	1.3.6.1.4.1.164.3.1.6.1.4.1.1.8	Unsigned32	read-write	Dedicated VLAN ID for multicast messages.
U32 ethIfSrcMacCtrlAddrIdx3	1.3.6.1.4.1.164.3.1.6.1.7.2.1.3	Unsigned32	not-accessible	A third index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.
U32 ethIfSrcMacCtrlAddrIndex	1.3.6.1.4.1.164.3.1.6.1.7.2.1.1	Unsigned32	not-accessible	The index of the interface for which the source MAC addresses exist in this table. It may be the ifIndex of the ETH/Bridge Port.
U32 ethIfSrcMacCtrlAging	1.3.6.1.4.1.164.3.1.6.1.7.1.1.7	Unsigned32	read-write	The timeout period in seconds for aging out dynamically learned source MAC addresses. Valid Values: 0 - disable 10-1000000
U32 ethIfSrcMacCtrlCurNumPermitAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.5	Unsigned32	read-only	This is the number of source MAC addresses currently permitted for the current interface.
U32 ethIfSrcMacCtrlIdx2	1.3.6.1.4.1.164.3.1.6.1.7.1.1.2	Unsigned32	not-accessible	A second index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.
U32 ethIfSrcMacCtrlIndex	1.3.6.1.4.1.164.3.1.6.1.7.1.1.1	Unsigned32	not-accessible	The index of the MAC Layer interface supporting source MAC control feature. It may be the ifIndex of the ETH/Bridge Port.
U32 ethIfSrcMacCtrlMaxPermitAddr	1.3.6.1.4.1.164.3.1.6.1.7.1.1.4	Unsigned32	read-write	This is the maximum number of permitted MAC addresses (static and learned) for the current interface.
U32 ethIfStormCnfgIdx	1.3.6.1.4.1.164.3.1.6.1.5.1.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 ethIfStormIfIdx	1.3.6.1.4.1.164.3.1.6.1.5.1.1.2	Unsigned32	not-accessible	A unique index of the ethernet interface/port.
U32 ethIfStormMaxRate	1.3.6.1.4.1.164.3.1.6.1.5.1.1.6	Unsigned32	read-write	This object indicates the Maximum Rate at which Storming packets are forwarded, in Kbps.For some devices the units are PPS(Packets Per Second ) or kilobytes per second.
U32 ethOamServiceFrameLossRatio	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.13	Unsigned32	read-only	Indicates the ratio of the lost frames since the time the service is up. The value is the ratio multiplied by 1E10. 0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).
U32 ethOamServiceIdx	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.1	Unsigned32	not-accessible	This object indicates the Index of the service being accessed.
U32 ethOamServicePriority	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.3	Unsigned32	read-create	This object determines the priority of the service. It is sent as P bits in an OAM message originated by this service.
U32 ethOamServiceUnavailRatio	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.16	Unsigned32	read-only	Indicates the ratio of the unavailable seconds since the time the service is up. The value is the ratio multiplied by 1E10. 0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).
U32 ethOamStdEtherType	1.3.6.1.4.1.164.3.1.6.1.3.6	Unsigned32	read-write	The Standard Ether Type in an OAM message. This object will be RW until a formal value will be issued for standard Ethernet Type. When such Standard will exist, this object will be supported RO to reflect the Standard value.
U32 ethOamSvcCurrAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.9	Unsigned32	read-only	The average round trip delay in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.11	Unsigned32	read-only	The average round trip delay variation in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.8	Unsigned32	read-only	The maximum value of round trip delay in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.10	Unsigned32	read-only	The maximum value of round trip delay variation in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcCurrMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.7	Unsigned32	read-only	The mininal value of round trip delay in the current interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.10	Unsigned32	read-only	The average round trip delay in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.12	Unsigned32	read-only	The average round trip delay variation in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.9	Unsigned32	read-only	The maximum value of round trip delay in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.11	Unsigned32	read-only	The maximum value of round trip delay variation in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcIntervalMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.8	Unsigned32	read-only	The mininal value of round trip delay in the selected interval. Values units are of 0.1 msec.
U32 ethOamSvcTotalAvgRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.9	Unsigned32	read-only	The average round trip delay in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalAvgRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.11	Unsigned32	read-only	The average round trip delay variation in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.8	Unsigned32	read-only	The maximum value of round trip delay in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalMaxRoundTripDVar	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.10	Unsigned32	read-only	The maximum value of round trip delay variation in the last 24H. Values units are of 0.1 msec.
U32 ethOamSvcTotalMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.7	Unsigned32	read-only	The mininal value of round trip delay in the last 24H. Values units are of 0.1 msec.
U32 evcCosCnfgIdx	1.3.6.1.4.1.164.6.3.7.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 evcCosEvcIdx	1.3.6.1.4.1.164.6.3.7.1.2	Unsigned32	not-accessible	This attribute indicates EVC Id.
U32 evcCosSpVlanId	1.3.6.1.4.1.164.6.3.7.1.6	Unsigned32	read-create	This object indicates the SP (Service Provider) VLAN used when sending an OAM message for the specified EVC.
U32 fileTransferServerPort	1.3.6.1.4.1.164.6.2.12.14	Unsigned32	read-write	Server Port number used for File Transfer. Applicable for SFTP. Valid values: 0..65535.
U32 flowIndex	1.3.6.1.4.1.164.6.3.6.1.1	Unsigned32	not-accessible	Defines the Flow ID the service is associated to.
U32 flowMappingProfileIndex	1.3.6.1.4.1.164.6.3.9.1.1.1	Unsigned32	not-accessible	A running index for the Flow Mapping Profile table.
U32 flowMappingProfileMapIndex	1.3.6.1.4.1.164.6.3.9.1.1.5	Unsigned32	read-create	This attribute holds a reference to the mapping index. It specifies the mapping selected for the Mapping Profile for the selected Priority. When flowMappingProfileNumOfMaps=0, this attribute is not relevant.
U32 flowMappingProfileNumOfMaps	1.3.6.1.4.1.164.6.3.9.1.1.4	Unsigned32	read-create	This attribute determines the number of the mappings associated to the Flow Mapping Profile.
U32 gfpCnfgIdx	1.3.6.1.4.1.164.6.2.55.1.1.1	Unsigned32	not-accessible	Index to GFP configuration table.
U32 ifCreateParams	1.3.6.1.4.1.164.6.2.35.1.1.8	Unsigned32	read-create	This object represents one or more parameters of the created Interface. Each group of bits (one or more bits) represents a specific parameter and its possible values. This object's mapping and interpretation will be specified in each device's specification documents. The parameter should be used within the create PDU assuming atomic operation.
U32 ifPerfHighCounterPart	1.3.6.1.4.1.164.6.2.35.2.1.1.3	Unsigned32	read-only	This parameter holds the High 32 bits of the counter (see description in the above parameter).
U32 ifPerfLowCounterPart	1.3.6.1.4.1.164.6.2.35.2.1.1.2	Unsigned32	read-only	In order to support Counters having 64 bit length, the performance counter is divided into two 32 bit parameters as follows: [ 64 bit parameter ] = [ High 32 bit parameter ][ Low 32 bit parameter ]. This parameter holds the Low 32 bits of the counter, while the following parameter holds the High 32 bits of the counter.
U32 ip2IfCdisCngDetectionTime	1.3.6.1.4.1.164.3.1.6.7.1.1.85	Unsigned32	read-create	When working with CDIS (Call DIScrimination method) or CNG (Comfort Noise Generation): The time in msec that the device will detect 1100Hz & 2100Hz signals on the line before switching to modem or fax. For Vmux: the values will be in steps of 10 msec.
U32 ip2IfCurrentStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.10.1.6	Unsigned32	read-only	The Maximum jitter buffer level (in msec) for the current interval.
U32 ip2IfCurrentStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.10.1.5	Unsigned32	read-only	The Minimum jitter buffer level (in msec) for the current interval.
U32 ip2IfDtdErlRatioCutoffQ3	1.3.6.1.4.1.164.3.1.6.7.1.1.77	Unsigned32	read-create	The DTD ERL cutoff level is used in order to determine whether the near-end is talking or not. This parameter is used by the echo canceller when echo exists and there is voice with low volume on the line. DTD means Double Talk Detection. ERL means Echo Return Loss. It is the power difference [dB] between the far-end signal to the echo returned. The cutoff level is calculated for the value entering Q.3. This value will be divided by 2^3=8 in order to get the linear ratio.
U32 ip2IfIntervalStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.11.1.7	Unsigned32	read-only	The Maximum jitter buffer level (in msec) for the selected interval.
U32 ip2IfIntervalStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.11.1.6	Unsigned32	read-only	The Minimum jitter buffer level (in msec) for the selected interval.
U32 ip2IfMaxGprsTxQueue	1.3.6.1.4.1.164.3.1.6.7.1.1.82	Unsigned32	read-create	Max GPRS Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on the network. High buffer size allows to store this burst and not lose packets.
U32 ip2IfMaxTxQueue	1.3.6.1.4.1.164.3.1.6.7.1.1.81	Unsigned32	read-create	Max Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on the network. High buffer size allows to store this burst and not lose packets.
U32 ip2IfNlpCutoffLevel	1.3.6.1.4.1.164.3.1.6.7.1.1.76	Unsigned32	read-create	Non Linear Processor (NLP) Cutoff Level for this bundle. This parameter is used by the echo canceller. It is the maximum absolute linear PCM amplitude of the near-end signal that will cause the NLP module to be active and to mute low level residual echo & noisy surroundings.
U32 ip2IfStatAvrRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.24	Unsigned32	read-only	The avarage Round Trip delay (in msec). 0= not applicable.
U32 ip2IfStatMaxJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.7.1.18	Unsigned32	read-only	The Maximum jitter buffer level (in msec).
U32 ip2IfStatMaxRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.23	Unsigned32	read-only	The maximum Round Trip delay (in msec). 0= not applicable.
U32 ip2IfStatMinJittBufLevel	1.3.6.1.4.1.164.3.1.6.7.7.1.17	Unsigned32	read-only	The Minimum jitter buffer level (in msec).
U32 ip2IfStatMinRoundTripDelay	1.3.6.1.4.1.164.3.1.6.7.7.1.22	Unsigned32	read-only	The minimum Round Trip delay (in msec). 0= not applicable.
U32 ip2IfStatRecommendedJittBufSize	1.3.6.1.4.1.164.3.1.6.7.7.1.19	Unsigned32	read-only	The Recommended jitter buffer Size (in msec). 0= not applicable.
U32 ip2IfVbdSwitchbackTime	1.3.6.1.4.1.164.3.1.6.7.1.1.87	Unsigned32	read-create	Time in msec required for the DSP to switch back from VBD (Voice Band Data) to Voice. For Vmux: the values will be in steps of 30 msec.
U32 lagCnfgIdx	1.3.6.1.4.1.164.6.2.54.1.1.1	Unsigned32	not-accessible	This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
U32 lagIdx	1.3.6.1.4.1.164.6.2.54.1.1.2	Unsigned32	not-accessible	This object indicates LAG unique index.
U32 lagShutDownDurationUponFlip	1.3.6.1.4.1.164.6.2.54.1.1.8	Unsigned32	read-create	This object defines the duration (in seconds) the active port transmission is shut down after LAG Flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0=no shut-down. This object is applicable only when lagDistributionMethod=oneToOne(3) and mainly when each of the Links of our device is connected to a different device.
U32 lagStatActivePort	1.3.6.1.4.1.164.6.2.54.2.1.2	Unsigned32	read-only	This object indicates the current active port. It is applicable only when lagDistributionMethod = oneToOne. The value is the ifIndex of the port. 0 = none of the ports is active.
U32 lagStatForcePort	1.3.6.1.4.1.164.6.2.54.2.1.1	Unsigned32	read-write	This object enables user to enforce the active port. 0 = No Enforcement; Otherwise the ifIndex of the port.
U32 lagWaitToRestore	1.3.6.1.4.1.164.6.2.54.1.1.6	Unsigned32	read-create	This object defines traffic recovery time (in seconds) to the port after its recovery. This object is applicable only when lagRecoveryMode= revertive (3).
U32 markingProfileIndex	1.3.6.1.4.1.164.6.3.12.1.1	Unsigned32	not-accessible	Defines the Marking Profile ID.
U32 mngSnmpTrapUdpPort	1.3.6.1.4.1.164.6.2.7.1.6	Unsigned32	read-write	This variable enables to set the UDP port (socket) used for SNMP traps.
U32 optPrtCnfgIdx	1.3.6.1.4.1.164.6.2.15.8.2.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.x.
U32 optPrtCnfgPrtIdx	1.3.6.1.4.1.164.6.2.15.8.2.1.2	Unsigned32	not-accessible	This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
U32 portTypicalMaxRange	1.3.6.1.4.1.164.6.2.15.1.1.8	Unsigned32	read-only	Maximum range supported by SFP port, in meter units.
U32 prtExPVc4SigPacketInterval	1.3.6.1.4.1.164.3.2.3.2.9.1.1.52	Unsigned32	read-write	Defines the Signaling Packetizing Interval, which is the maximum time interval, measured in msec (milliseconds), between multiplexed signaling frames.
U32 prtExVcPbxTsRemConnID	1.3.6.1.4.1.164.3.2.3.2.15.4.1.11	Unsigned32	read-write	This attribute indicates the Connection ID with the Remote unit. notApplicable = 0.
U32 prtExVcPbxTsSourcePrt	1.3.6.1.4.1.164.3.2.3.2.15.4.1.13	Unsigned32	read-write	For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Port within the Slot of the Analog Voice Card, we want to compress. exPrt1 - exPrt16 = 1 - 16 noConnect=100 - when prtExVcPbxTsCvServiceSlot=noConnect.
U32 prtIpParamBurstSize	1.3.6.1.4.1.164.6.2.15.6.1.1.32	Unsigned32	read-write	The burst size that the port can support beyond rate limitation determined in prtIpParamRateLimit. Burst Size is measured in bytes.
U32 prtParamDataRate	1.3.6.1.4.1.164.6.2.15.5.1.1.19	Unsigned32	read-write	Rate of serial data port (V.11, V.24, V.35) in kbps units.
U32 prtParamFarEndDevice	1.3.6.1.4.1.164.6.2.15.5.1.1.26	Unsigned32	read-write	Programmed Far-End device connected to this port. This object is relevant for products having multiple DBs. It will enable configuring offline, the relevant data. For MP-4100, LRS-102 OP-108/106 cards, the options will be: 1 = None (when a port is not connected to any remote device) 2 = OP-108 3 = OP-108/ETH 4 = OP-106 5 = OP-106/ETH 6 = card of MP or LRS-102
U32 prtQosIdx	1.3.6.1.4.1.164.6.3.4.2.1.1	Unsigned32	not-accessible	The first index of the table. This attribute might indicate the Idx of the Cnfg (1..255) being accessed ; Idx of 255 relates to the TmpCnfg or any other Index.
U32 prtQosPrtIdx	1.3.6.1.4.1.164.6.3.4.2.1.2	Unsigned32	not-accessible	This object indicates a unique Port Index. Refer to device specification for port Index.
U32 prtQosRateLimitCBS	1.3.6.1.4.1.164.6.3.4.2.1.6	Unsigned32	read-write	This object indicates the port's CBS (Committed Burst Size) in KB. Value=0 represents best effort.
U32 prtQosRateLimitCIR	1.3.6.1.4.1.164.6.3.4.2.1.5	Unsigned32	read-write	This object indicates the port's CIR (Committed Information Rate) in Kbps. Value=0 represents best effort.
U32 prtQosRateLimitEBS	1.3.6.1.4.1.164.6.3.4.2.1.8	Unsigned32	read-write	This object indicates the port's EBS (Excess Burst Size) in KB.
U32 prtQosRateLimitEIR	1.3.6.1.4.1.164.6.3.4.2.1.7	Unsigned32	read-write	This object indicates the port's EIR (Excess Information Rate) in Kbps.
U32 prtTestActivationDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.13	Unsigned32	read-write	This object is applicable only when a single test is running. It indicates test activation delay in seconds. A Value of 0 indicates that the test starts immediately.
U32 prtTestBwProfile	1.3.6.1.4.1.164.6.2.15.4.1.1.25	Unsigned32	read-write	Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test in order to limit the traffic that is looped back.
U32 prtTestOamAvgRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.21	Unsigned32	read-only	The average round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamMaxRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.20	Unsigned32	read-only	The maximum value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamMinRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.19	Unsigned32	read-only	The mininal value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamTxInterval	1.3.6.1.4.1.164.6.2.15.4.1.1.22	Unsigned32	read-write	Indicates the interval between loopback sent messages.Units are msec.
U32 prtTestTTL	1.3.6.1.4.1.164.6.2.15.4.1.1.24	Unsigned32	read-write	Time-to-live.Number of hops the loopback message will go through the net before deciding to discard it.
U32 qInternalProfileIndex	1.3.6.1.4.1.164.6.3.11.2.1.1	Unsigned32	not-accessible	Defines the Queue Profile ID.
U32 qInternalProfileQueueLength	1.3.6.1.4.1.164.6.3.11.2.1.5	Unsigned32	read-create	This attribute determines the length of the queue.
U32 qInternalProfileRateLimit	1.3.6.1.4.1.164.6.3.11.2.1.9	Unsigned32	read-create	This attribute determines the Rate Limit of the queue in Kbps. Value=0 represents best effort.
U32 qInternalProfileShaperProfile	1.3.6.1.4.1.164.6.3.11.2.1.10	Unsigned32	read-create	This attribute defines the Shaper Profile (bwProfileIndex from bwProfileTable) assigned to this qInternalProfile. Valid range of bwProfileIndex for Shaper Profiles is 0x8000001-0x8000041. If set to '0', no profile is assigned to this qInternalProfile.
U32 qInternalProfileWFQWeight	1.3.6.1.4.1.164.6.3.11.2.1.4	Unsigned32	read-create	This attribute determines the weight that each WFQ (Weighted Fair Queue) participant gets. It is applicable only when scheduling is configured to WFQ.
U32 qInternalProfileWredDropAllThresh	1.3.6.1.4.1.164.6.3.11.2.1.7	Unsigned32	read-create	This attribute determines the length that the queue (Stop Value) must reach before the WRED (Weighted Random Early Detection) shaper mechanism stops dropping randomly, and just drops all further packets marked as yellow.
U32 qInternalProfileWredDropProbability	1.3.6.1.4.1.164.6.3.11.2.1.8	Unsigned32	read-create	This attribute determines the percentage of packets that are being dropped at the point when the length of the queue reaches the Stop value. So, effectively, this defines how quickly the rate of dropping packet must increase as the queue length grows from the Start Value to the Stop Value.
U32 qInternalProfileWredStartDropThresh	1.3.6.1.4.1.164.6.3.11.2.1.6	Unsigned32	read-create	This attribute determines the length that the queue (Start Value) must reach before the packets colored yellow will start being dropped by the WRED (Weighted Random Early Detection/Discard) mechanism. WRED is one the most commonly used method for congestion avoidance.
U32 qosFlowMappingFromDscp	1.3.6.1.4.1.164.6.3.9.2.1.8	Unsigned32	read-create	This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromInnerVlanId	1.3.6.1.4.1.164.6.3.9.2.1.31	Unsigned32	read-create	This attribute determines the first inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromIpPrecedence	1.3.6.1.4.1.164.6.3.9.2.1.28	Unsigned32	read-create	This attribute determines the first IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromTcpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.22	Unsigned32	read-create	This attribute determines the first TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromTcpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.20	Unsigned32	read-create	This attribute determines the first TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromUdpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.26	Unsigned32	read-create	This attribute determines the first UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromUdpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.24	Unsigned32	read-create	This attribute determines the first UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingFromVlanId	1.3.6.1.4.1.164.6.3.9.2.1.10	Unsigned32	read-create	This attribute determines the first VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingIdx1	1.3.6.1.4.1.164.6.3.9.2.1.1	Unsigned32	not-accessible	- In case the table is accessed via flowMappingProfileTable this is a running index for the QoS Flow Mapping table. - In case the table is not accessed via flowMappingProfileTable, this will be the ifIndex of the XNI (bridge port) to which the QoS mapping applies.
U32 qosFlowMappingIdx2	1.3.6.1.4.1.164.6.3.9.2.1.2	Unsigned32	not-accessible	An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the index of the Flow (EVC) to which the QoS mapping applies.
U32 qosFlowMappingIdx3	1.3.6.1.4.1.164.6.3.9.2.1.3	Unsigned32	not-accessible	An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the Priority to which the QoS mapping applies.
U32 qosFlowMappingIeee802dot1p	1.3.6.1.4.1.164.6.3.9.2.1.6	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different 802.1 P-bit value. Setting '1' to the bit means that the corresponding 802.1 P-bit value is applicable. It is relevant only in case the ieee802dot1p bit(0) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingInnerIeee802dot1p	1.3.6.1.4.1.164.6.3.9.2.1.30	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different inner 802.1 P-bit value. Setting '1' to the bit means that the corresponding inner 802.1 P-bit value is applicable. It is relevant only in case the innerIeee802dot1p bit (13) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToDscp	1.3.6.1.4.1.164.6.3.9.2.1.9	Unsigned32	read-create	This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToInnerVlanId	1.3.6.1.4.1.164.6.3.9.2.1.32	Unsigned32	read-create	This attribute determines the last inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToIpPrecedence	1.3.6.1.4.1.164.6.3.9.2.1.29	Unsigned32	read-create	This attribute determines the last IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingTos	1.3.6.1.4.1.164.6.3.9.2.1.7	Unsigned32	read-create	This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different TOS value. Setting '1' to the bit means that the corresponding TOS value is applicable. It is relevant only in case the tos bit (1) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToTcpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.23	Unsigned32	read-create	This attribute determines the last TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToTcpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.21	Unsigned32	read-create	This attribute determines the last TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToUdpDestPort	1.3.6.1.4.1.164.6.3.9.2.1.27	Unsigned32	read-create	This attribute determines the last UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToUdpSrcPort	1.3.6.1.4.1.164.6.3.9.2.1.25	Unsigned32	read-create	This attribute determines the last UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.
U32 qosFlowMappingToVlanId	1.3.6.1.4.1.164.6.3.9.2.1.11	Unsigned32	read-create	This attribute determines the last VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.
U32 qProfileIndex	1.3.6.1.4.1.164.6.3.11.1.1.1	Unsigned32	not-accessible	Defines the Queue Cluster Profile ID.
U32 qProfileNumberOfInternalQ	1.3.6.1.4.1.164.6.3.11.1.1.4	Unsigned32	read-create	This attribute holds the number of the internal queue profiles that are pointed by qInternalQProfile.
U32 queueGroupPointToInternalQueue	1.3.6.1.4.1.164.6.3.11.3.1.8	Unsigned32	read-create	This attribute defines the internal queue whithin queueGroupPointToQBlock that is pointed by this Queue Block.
U32 queueGroupQBlockIdx	1.3.6.1.4.1.164.6.3.11.3.1.3	Unsigned32	not-accessible	This attribute holds the ID of the Queue Block. NA=2^32-1.
U32 queueGroupQBlockLevel	1.3.6.1.4.1.164.6.3.11.3.1.2	Unsigned32	not-accessible	This attribute holds the Level of the Queue Block .First level is 1. NA=2^32-1.
U32 queueGroupQBlockProfile	1.3.6.1.4.1.164.6.3.11.3.1.5	Unsigned32	read-create	This attribute defines the Queue profile assigned to this Queue Block. This object points to qProfileIndex in qProfileTable.
U32 queueGroupQBlockShaperProfile	1.3.6.1.4.1.164.6.3.11.3.1.6	Unsigned32	read-create	This attribute defines the Shaper profile assigned to this Queue Block.
U32 radBridgeEthType	1.3.6.1.4.1.164.4.1.9.4.1.8	Unsigned32	read-write	Value of Ethertype field in Ethernet frame. This field indicates which protocol is being transported in an ethernet frame.
U32 radBridgeLoopDetectVlanId	1.3.6.1.4.1.164.4.1.9.4.1.6	Unsigned32	read-write	This variable indicates the VLAN ID used for Loop Detection packets. Valid values: 1 - 4095: VLAN ID 0 - Means that the Loop Detection is Disabled.
U32 radBridgeMngVlanId	1.3.6.1.4.1.164.4.1.9.4.1.5	Unsigned32	read-write	This variable indicates the VLAN ID used for remote management traffic. 0 = Not Applicable.
U32 radDot1qPortVlanEthType	1.3.6.1.4.1.164.4.1.9.3.1.8	Unsigned32	read-write	This object indicates the Ethernet Type. For some devices, it is applicable only when radDot1qPortStacking = stack.
U32 radMdIndex	1.3.6.1.4.1.164.3.1.6.1.3.3.1.1	Unsigned32	not-accessible	The index to the maintenance domain table.
U32 radMepCcStatusRemMepId	1.3.6.1.4.1.164.3.1.6.1.3.5.1.2	Unsigned32	read-create	This attribute indicates the Remote MEP ID from which the CC messages has arrived.
U32 radMepDefaultPriority	1.3.6.1.4.1.164.3.1.6.1.3.1.1.12	Unsigned32	read-create	This object defines the priority of the OAM messages sent when no service is defined on EVC. If a service is defined, the OAM messages will get the highest service priority existing on the EVC.
U32 radMepIdx	1.3.6.1.4.1.164.3.1.6.1.3.1.1.3	Unsigned32	not-accessible	This object indicates the ID of the MEP being accessed.
U32 radMepLocalMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.5	Unsigned32	read-create	This object indicates the local MEP ID.
U32 radMepLtrReceiveOrder	1.3.6.1.4.1.164.3.1.6.1.3.4.1.1	Unsigned32	not-accessible	An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. radMepLtrReceiveOrder are assigned sequentially from 1, in the order that the Linktrace Initiator received the LTRs.
U32 radMepLtrTtl	1.3.6.1.4.1.164.3.1.6.1.3.4.1.2	Unsigned32	read-only	TTL field value for a returned LTR.
U32 radMepMdId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.15	Unsigned32	read-create	The index of the Maintenance Domain in the radMdTable (radMdIndex).
U32 radMepMeLevel	1.3.6.1.4.1.164.3.1.6.1.3.1.1.9	Unsigned32	read-create	At any point in a network, ME Level is used to distinguish between OAM signals belonging to different nested MEs. Maintenance Entity Levels are defined as follows: 0,1,2 are assigned to customers 3,4 are assigned to providers 5,6,7 are assigned to operators.
U32 radMepRemoteMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.6	Unsigned32	read-create	This atribute is currently implemneted at radMepCcTable, that supports multicast.
U32 radMepRemoteMepIdx	1.3.6.1.4.1.164.3.1.6.1.3.5.1.1	Unsigned32	not-accessible	This is a running index for arriving CC messages (from different Remote MEPs) for a specific MEP ID.
U32 radMepSpVlanId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.18	Unsigned32	read-create	The SP (Service Provider) VLAN used when sending an OAM message.
U32 radMepTransmitLbmDestMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.21	Unsigned32	read-create	The MEPID of another MEP in the same MA to which the LBM is to be sent. This address will be used if the value of radMepTransmitLbmDestIsMepId is yes (3). 802.1ag clause 12.14.7.3.2:b.
U32 radMepTransmitLbmVlanPriority	1.3.6.1.4.1.164.3.1.6.1.3.1.1.24	Unsigned32	read-create	The priority to be used in the VLAN tag, if present, in the transmitted frame. The default value is CCM priority. 802.1ag clause 12.14.7.3.2:e
U32 radMepTransmitLtmTargetMepId	1.3.6.1.4.1.164.3.1.6.1.3.1.1.30	Unsigned32	read-create	The MEPID of another MEP in the same MA to which LTM is to be transmitted. This address will be used if the value of radMepTransmitLtmTargetIsMepId is yes (3). 802.1ag clause 12.14.7.4.2:c.
U32 radMepTransmitLtmTtl	1.3.6.1.4.1.164.3.1.6.1.3.1.1.32	Unsigned32	read-create	The LTM TTL field. Default value, if not specified, is 64. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 each Linktrace Responder that handles the LTM. The value received in the LTM is returned in the LTR. If 0 on input, the LTM is not transmitted to the next hop. 802.1ag clause 12.14.7.4.2:b and 21.8.4.
U32 radOamEvcIdx	1.3.6.1.4.1.164.3.1.6.1.3.1.1.2	Unsigned32	not-accessible	This object indicates the Index of the EVC (Ethernet Virtual Circuit) that the MEP is associated to.
U32 radOamIdx1	1.3.6.1.4.1.164.3.1.6.1.3.1.1.1	Unsigned32	not-accessible	This object may indicate the Bridge Index or Configuration index.
U32 schedYear	1.3.6.1.4.1.164.6.2.14.5.1.1	Unsigned32	read-create	The year during which the scheduled action should take place.
U32 serviceBwProfileId	1.3.6.1.4.1.164.6.3.6.1.5	Unsigned32	read-create	This variable holds the index of the Ingress BW profile assigned to that service.
U32 serviceIndex	1.3.6.1.4.1.164.6.3.6.1.2	Unsigned32	not-accessible	Defines the Service ID - according to the CoS.
U32 sysCClkRecoveredID	1.3.6.1.4.1.164.3.3.1.6.1.1.12	Unsigned32	read-write	This entry indicates the Recovered Clock ID. The value will be applicable only when sysCClkSrcMode is 'recovered'.
U32 sysCRdnTxDownDurationUponFlip	1.3.6.1.4.1.164.3.3.1.6.3.1.23	Unsigned32	read-create	This object defines the duration (in seconds) the active port transmission is shut down after flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0 = no shut-down. This object is applicable only when sysCRdnMode = oneToOne(8) and mainly when each of the links of our device is connected to a different device.
U32 sysCRdnWTR	1.3.6.1.4.1.164.3.3.1.6.3.1.21	Unsigned32	read-create	Redundancy Wait to Restore (sec). Valid Values: 0..999, 65535. 65535=NA. When the value <> 65535, the value of sysCRdnRecTime must be 65535.
U32 systemNtpUpdateInterval	1.3.6.1.4.1.164.6.2.14.4.5	Unsigned32	read-write	This variable represents the NTP Update Interval, measured in seconds.
U32 systemVoiceCoderConfIdx	1.3.6.1.4.1.164.3.1.2.12.2.1.1	Unsigned32	not-accessible	The first index of the table. This object might represent the Configuration Index (1..100) being accessed; Index=255 relates to the TmpCnfg. For devices with multiple configurations, Set is permitted to TmpCnfg(255) only. Not-Applicable = 1.
U32 systemVoiceCoderPriority	1.3.6.1.4.1.164.3.1.2.12.2.1.2	Unsigned32	not-accessible	This object indicates the Coder's Priority.
U32 systemVoiceDtmfRelayRxPayloadType	1.3.6.1.4.1.164.3.1.2.12.1.1.11	Unsigned32	read-write	This object indicates the Rx Payload Type for DTMF relay RTP packets. It is relevant only when DTMF Relay Method is RFC-2833.
U32 systemVoiceDtmfRelayTxPayloadType	1.3.6.1.4.1.164.3.1.2.12.1.1.13	Unsigned32	read-write	This object indicates the Tx Payload Type for DTMF relay RTP packets. It is relevant only when the Payload Type Negotiation is disabled.
U32 systemVoicePacketRate	1.3.6.1.4.1.164.3.1.2.12.1.1.3	Unsigned32	read-write	This object indicates the G.729 and G.711 Coders transmitted Packet Rate in milliseconds.
U32 wfqMaxPacketSize	1.3.6.1.4.1.164.6.3.1.1.1.9	Unsigned32	read-create	The size of the largest packet which can be received on this queue, specified in octets. Packets larger than this size will be discarded.
U32 wfqMinRateAbsolute	1.3.6.1.4.1.164.6.3.1.1.1.8	Unsigned32	read-create	The minimum absolute rate, in kbps, that should be allocated to this queue. If the value is zero, then there is effectively no minimum rate guarantee. If the value is non-zero, then the servicing of this queue in at least this rate is assured. Note that when this attribute is being used, the wfqWeightValue attribute is NA.
No type (1307)
agnAccess	1.3.6.1.4.1.164.6.2.34
NTF agnActualLowRate	1.3.6.1.4.1.164.6.1.0.21			The main link is synchronized at a rate lower than expected.
NTF agnAlarmBufferClear	1.3.6.1.4.1.164.6.1.0.18			This trap indicates that alarm buffer has been cleared.
NTF agnAlarmBufferOverflow	1.3.6.1.4.1.164.6.1.0.17			This trap indicates that the quantity of alarm messages which have been written in the alarm buffer, since the last clear command, exceeds predefined threshold. (Buffer size) The new alarms are overwriting the oldest alarms (the first alarms written in the buffer). For LA-110,threshold value is 200 alarms.
agnAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.2.3.3.1		not-accessible	An entry in table.
agnAlarmsCmprTable	1.3.6.1.4.1.164.3.1.2.3.3		not-accessible	A table.
agnAlrBufCmprEntry	1.3.6.1.4.1.164.3.1.2.3.4.1		not-accessible	An entry in table.
agnAlrBufCmprTable	1.3.6.1.4.1.164.3.1.2.3.4		not-accessible	A table.
agnCAgendaEntry	1.3.6.1.4.1.164.3.1.2.5.1.1		not-accessible	An entry in table.
agnCAgendaTable	1.3.6.1.4.1.164.3.1.2.5.1		not-accessible	This table devides the week days into categories needed for DB flip consideration.
agnCBuMlEntry	1.3.6.1.4.1.164.3.1.2.2.12.1		not-accessible	An Entry in table agnCBuMlTable
agnCBuMlTable	1.3.6.1.4.1.164.3.1.2.2.12		not-accessible	Configuration for Primary, Secondary and Third Link. These are used for Link Backup.
agnCClkSrcEntry	1.3.6.1.4.1.164.3.1.2.2.4.1		not-accessible	An entry in table.
agnCClkSrcTable	1.3.6.1.4.1.164.3.1.2.2.4		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
agnCFlipEntry	1.3.6.1.4.1.164.3.1.2.5.3.1		not-accessible	An entry in table.
agnCFlipNetEventsEntry	1.3.6.1.4.1.164.3.1.2.5.2.1		not-accessible	An entry in table.
agnCFlipNetEventsTable	1.3.6.1.4.1.164.3.1.2.5.2		not-accessible	This table holds the Net Events the MUX should trace
agnCFlipTable	1.3.6.1.4.1.164.3.1.2.5.3		not-accessible	The DB Flip Decisions Table
agnClkCurrentEntry	1.3.6.1.4.1.164.6.2.52.3.1.1		not-accessible	An entry in the Clock Current table.
agnClkCurrentTable	1.3.6.1.4.1.164.6.2.52.3.1		not-accessible	The Clock Current table.
agnClkIntervalEntry	1.3.6.1.4.1.164.6.2.52.3.2.1		not-accessible	An entry in the Clock Interval table.
agnClkIntervalTable	1.3.6.1.4.1.164.6.2.52.3.2		not-accessible	The Clock Interval table.
NTF agnClkSrcFrequencyAlarmTrap	1.3.6.1.4.1.164.6.1.0.31			The trap is sent upon Recovered Clock Frequency alarm.
agnClkSrcPortEntry	1.3.6.1.4.1.164.6.2.52.1.1		not-accessible	An entry in the table.
agnClkSrcPortTable	1.3.6.1.4.1.164.6.2.52.1		not-accessible	Pool of Ports for the Master/Fallback Clock Source and of Recovered IDs. For devices with more than one configuration: Set operation is valid only to the TmpCnfg entry.
NTF agnClkSrcStateChangeTrap	1.3.6.1.4.1.164.6.1.0.28			The trap is sent upon change in Recovery Clock State.
agnClockMonitoring	1.3.6.1.4.1.164.6.2.52.3
agnClockSource	1.3.6.1.4.1.164.6.2.52
agnCmprEntry	1.3.6.1.4.1.164.3.1.2.3.1.1		not-accessible	An entry in table.
agnCmprTable	1.3.6.1.4.1.164.3.1.2.3.1		not-accessible	A table.
agnCnfgAlarm	1.3.6.1.4.1.164.3.1.2.2.8
agnCnfgAlrEntry	1.3.6.1.4.1.164.3.1.2.2.8.2.1		not-accessible	An entry in table.
agnCnfgAlrReportEntry	1.3.6.1.4.1.164.3.1.2.2.8.3.1		not-accessible	An entry in table.
agnCnfgAlrReportTable	1.3.6.1.4.1.164.3.1.2.2.8.3		not-accessible	This table enables the user to configure the desired Alarm Reports according to alarms severity.
agnCnfgAlrTable	1.3.6.1.4.1.164.3.1.2.2.8.2		not-accessible	This table enables the user to set attributes to each alarm. Setting for a non-existing entry agnCnfgAlrMask, agnCnfgAlrInvert or agnCnfgAlrFilter to 'yes'(or yesAndSave for Mask) will add this new entry to the table. Setting for an existing entry agnCnfgAlrMask/ agnCnfgAlrInvert/agnCnfgAlrFilter (one or more) to 'no' (noAndSave for Mask) so that ALL these objects' values are 'no' , will delete this entry from the table. For agnCnfgAlrMask, only if [(last saved value=noAndSave) AND (new value is 'no' or 'noAndSave')] the object's value is considered 'no' for deleting the entry. For some products (like MP, MPH, Vmux2100) the Active Alarms are always part of the table and cannot be removed even if their Mask/Invert/Filter are No.
agnCnfgDataEntry	1.3.6.1.4.1.164.3.1.2.2.7.1		not-accessible	An entry in table.
agnCnfgDataTable	1.3.6.1.4.1.164.3.1.2.2.7		not-accessible	This table contains data about the agent configurations. The table will support only data about valid configurations of the agent.
NTF agnConfigDBChecksumError	1.3.6.1.4.1.164.6.1.0.16			This trap indicates that the database currently stored in the non-volatile memory of the device is corrupted
NTF agnCounterChange	1.3.6.1.4.1.164.6.1.0.6			This notification is sent when the value of a specific Counter is changed. Agent can send as attached object the updated Counter. For details about this Counter and attached object, see spec of the relevant application.
agnCQ50Entry	1.3.6.1.4.1.164.3.1.2.2.13.1		not-accessible	An Entry in table agnCQ50Table
agnCQ50Table	1.3.6.1.4.1.164.3.1.2.2.13		not-accessible	Table for the device Q50 parameters. Q50 is a Signaling protocol used between PBX devices. It is possible to control the initiation of calls using Q.50. This is useful for devices when there is a congestion.
agnCT1E1RingEntry	1.3.6.1.4.1.164.3.1.2.2.10.1		not-accessible	An Entry in table agnCT1E1RingTable
agnCT1E1RingTable	1.3.6.1.4.1.164.3.1.2.2.10		not-accessible	Configuration of all T1/E1 Ring ML cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that does not participate in the T1/E1 Ring, will not exist in this table. A ML port that exists in this table, cannot exist at the same time in the IO Redundancy table (sysCRdnTable).
agnCurrClkEntry	1.3.6.1.4.1.164.6.2.52.2.1		not-accessible	An entry in the table.
agnCurrClkTable	1.3.6.1.4.1.164.6.2.52.2		not-accessible	Current Clock Source.
agnDlciCmprEntry	1.3.6.1.4.1.164.3.1.2.3.2.1		not-accessible	An entry in table.
agnDlciCmprTable	1.3.6.1.4.1.164.3.1.2.3.2		not-accessible	A table.
agnDlciEntry	1.3.6.1.4.1.164.3.1.2.8.1.1		not-accessible	An entry in table.
agnDlciTable	1.3.6.1.4.1.164.3.1.2.8.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
NTF agnDriverSwMismatch	1.3.6.1.4.1.164.6.1.0.20			There is mismatch between the SW driver and the HW of the device uplink interface.
NTF agnFanFailureTrap	1.3.6.1.4.1.164.6.1.0.14			This trap is sent upon fan failure/recovery.
agnFlipDb	1.3.6.1.4.1.164.3.1.2.5
agnFlipDbControls	1.3.6.1.4.1.164.3.1.2.5.4
agnFunctionEntry	1.3.6.1.4.1.164.6.2.45.1		not-accessible	An entry in the table.
agnFunctionTable	1.3.6.1.4.1.164.6.2.45		not-accessible	This table is used in order to activate/deactivate device functions. The index indicates the function. Each function can be Enabled or Disabled.
agnGroupEntry	1.3.6.1.4.1.164.6.2.56.1		not-accessible	An entry in the agnGroupTable.
agnGroupTable	1.3.6.1.4.1.164.6.2.56		not-accessible	A table that enables associating components to Group/s (or removing components of a group). The Group Idx can then be used in other tables (e.g alarmForwardingTable).
agnLinkMapEntry	1.3.6.1.4.1.164.3.1.5.1.1		not-accessible	An entry in table.
agnLinkMapTable	1.3.6.1.4.1.164.3.1.5.1		not-accessible	A table.
agnListDecoding	1.3.6.1.4.1.164.3.1.2.7
agnListDecodingEntry	1.3.6.1.4.1.164.3.1.2.7.1.1		not-accessible	An entry in table.
agnListDecodingTable	1.3.6.1.4.1.164.3.1.2.7.1		not-accessible	A decoding table . For each type of list, a description is given for each existing code.
agnMux	1.3.6.1.4.1.164.3.2.1
NTF agnParametersValueChanged	1.3.6.1.4.1.164.6.1.0.19			This trap indicates that due to software upgrade, some of the parameters are assigned new values
NTF agnPowerFailureTrap	1.3.6.1.4.1.164.6.1.0.13			This trap is sent upon power failure. It is applicable for the following devices: 1. Devices having one PS unit, which sense the failure in advance, and still have time to send this trap before it goes off. 2. Devices having 2 PS units and send this trap in order to notify a failure in one of the units.
agnRowPointerEntry	1.3.6.1.4.1.164.6.2.63.1		not-accessible	An entry in the table.
agnRowPointerTable	1.3.6.1.4.1.164.6.2.63		not-accessible	This table holds information about a specific entry in a table. For example, number of usages of this row.
agnSa	1.3.6.1.4.1.164.3.1.2.6
agnSAlrEntry	1.3.6.1.4.1.164.3.1.2.1.15.1		not-accessible	An entry in table.
agnSAlrTable	1.3.6.1.4.1.164.3.1.2.1.15		not-accessible	List of agent related alarms and indications for alarms at system level.
agnSCmprErrListEntry	1.3.6.1.4.1.164.3.1.2.3.5.1		not-accessible	An entry in table.
agnSCmprErrListTable	1.3.6.1.4.1.164.3.1.2.3.5		not-accessible	A table.
agnSCnfgEntry	1.3.6.1.4.1.164.3.1.2.1.22.1		not-accessible	An entry in table.
agnSCnfgTable	1.3.6.1.4.1.164.3.1.2.1.22		not-accessible	This table contains an entry per configuration. It indicates if the configuration is valid.
NTF agnSelfTestResultChangeTrap	1.3.6.1.4.1.164.6.1.0.29			The trap is sent upon each change in the result of a Self State operation.
agnSErrListEntry	1.3.6.1.4.1.164.3.1.2.1.20.1		not-accessible	An entry in table.
agnSErrListTable	1.3.6.1.4.1.164.3.1.2.1.20		not-accessible	List of errors and warnings found during Sanity Check process.
agnSigProfEntry	1.3.6.1.4.1.164.3.1.2.10.2.1		not-accessible	An entry in table.
agnSigProfile	1.3.6.1.4.1.164.3.1.2.10
agnSigProfileEntry	1.3.6.1.4.1.164.3.1.2.10.1.1		not-accessible	An entry in table.
agnSigProfileTable	1.3.6.1.4.1.164.3.1.2.10.1		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to agnSigProfileCnfgIdx=1. The table includes signaling profile parameters for Legacy Profiles.
agnSigProfTable	1.3.6.1.4.1.164.3.1.2.10.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. This is the general table of signaling profiles.
NTF agnStationClkFailureTrap	1.3.6.1.4.1.164.6.1.0.23			This trap is sent upon Station Clock failure.
NTF agnStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.2			This trap is sent whenever the state of the entity the agent is responsible for changed. TDM devices will send agnTestStatus variable to indicate the current test status.
agnStringToIndexEntry	1.3.6.1.4.1.164.6.2.62.1		not-accessible	An entry in the table.
agnStringToIndexTable	1.3.6.1.4.1.164.6.2.62		not-accessible	This table holds the conversions of tables from unique String to numeric index.
agnSyslog	1.3.6.1.4.1.164.6.2.58
agnSystemDlci	1.3.6.1.4.1.164.3.1.2.8
NTF agnSystemParameterChangeTrap	1.3.6.1.4.1.164.6.1.0.15			This trap is sent upon any change of the systemParameter value.
agnSystemTs	1.3.6.1.4.1.164.3.1.2.11
agnt	1.3.6.1.4.1.164.6.2
agnTsCmprEntry	1.3.6.1.4.1.164.3.1.2.3.6.1		not-accessible	An entry in table.
agnTsCmprTable	1.3.6.1.4.1.164.3.1.2.3.6		not-accessible	A table.
NTF agnUploadDataTrap	1.3.6.1.4.1.164.6.1.0.11			This trap is sent upon an upload data session termination. For more details see product specification.
agnVoiceSwConfEntry	1.3.6.1.4.1.164.3.1.2.9.1.1		not-accessible	An entry in table.
agnVoiceSwConfHGEntry	1.3.6.1.4.1.164.3.1.2.9.5.1		not-accessible	An entry in table.
agnVoiceSwConfHGTable	1.3.6.1.4.1.164.3.1.2.9.5		not-accessible	Table of Hunt Groups.
agnVoiceSwConfRtEntry	1.3.6.1.4.1.164.3.1.2.9.2.1		not-accessible	An entry in table.
agnVoiceSwConfRtTable	1.3.6.1.4.1.164.3.1.2.9.2		not-accessible	Routing Table for Voice Switching.
agnVoiceSwConfTable	1.3.6.1.4.1.164.3.1.2.9.1		not-accessible	MXcess Configuration for Voice Switching.
agnVoiceSwitching	1.3.6.1.4.1.164.3.1.2.9
agnWanGen	1.3.6.1.4.1.164.3.1.2
agnXCmprEntry	1.3.6.1.4.1.164.3.1.2.3.7.1		not-accessible	An entry in table.
agnXCmprTable	1.3.6.1.4.1.164.3.1.2.3.7		not-accessible	A table.
NTF alarmAIS	1.3.6.1.4.1.164.6.1.3.0.10			This trap indicates AIS.
NTF alarmFEBE	1.3.6.1.4.1.164.6.1.3.0.12			This trap indicates FEBE.
alarmForwardingEntry	1.3.6.1.4.1.164.6.2.50.1		not-accessible	Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.
alarmForwardingTable	1.3.6.1.4.1.164.6.2.50		not-accessible	The Alarm Forwarding Mechanism will be operated for this table entries.
NTF alarmLOF	1.3.6.1.4.1.164.6.1.3.0.8			This trap indicates Loss Of Frame.
NTF alarmLOS	1.3.6.1.4.1.164.6.1.3.0.7			This trap indicates Loss Of Signal.
NTF alarmRDI	1.3.6.1.4.1.164.6.1.3.0.11			This trap indicates RDI.
NTF alarmStatusTrap	1.3.6.1.4.1.164.6.1.3.0.5			The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm.
NTF alarmsTrap	1.3.6.1.4.1.164.3.2.0.1			This trap is sent whenever alarm occurs in the agent.
alrBufEntry	1.3.6.1.4.1.164.3.1.2.4.1.1		not-accessible	An entry in table.
alrBuffGen	1.3.6.1.4.1.164.3.1.2.4
alrBufTable	1.3.6.1.4.1.164.3.1.2.4.1		not-accessible	A table.
alrGenEntry	1.3.6.1.4.1.164.3.3.4.3.1		not-accessible	An entry in table.
alrGenTable	1.3.6.1.4.1.164.3.3.4.3		not-accessible	A table.
NTF atmAceAlarmCluster	1.3.6.1.4.1.164.6.1.12.0.36			This trap is sent upon atmNteAlarmType start or end, for a cluster of VPs/VCs (according to atmNteLevel) with the same alarm on the same physical port. This trap replaces sending the same alarm for a big quantity (the quantity described in the product specification document) of VPs/VCs in order to prevent flooding the NMS and the network with traps.
NTF atmAceAlarmForwardingTrap	1.3.6.1.4.1.164.6.1.12.0.7			This trap is sent upon starting or stopping Alarm Forwarding Mechanism.
NTF atmAceAlarmLCD	1.3.6.1.4.1.164.6.1.12.0.18			This trap indicates Loss of Cell Delineation.
NTF atmAceAlarmLineAIS	1.3.6.1.4.1.164.6.1.12.0.21			This trap indicates Line AIS.
NTF atmAceAlarmLineBIP	1.3.6.1.4.1.164.6.1.12.0.26			This trap indicates Line Bit Interleave Parity.
NTF atmAceAlarmLineFEBE	1.3.6.1.4.1.164.6.1.12.0.28			This trap indicates Line Far End Block Error.
NTF atmAceAlarmLineRDI	1.3.6.1.4.1.164.6.1.12.0.23			This trap indicates Line RDI.
NTF atmAceAlarmLOF	1.3.6.1.4.1.164.6.1.12.0.17			This trap indicates Loss Of Frame.
NTF atmAceAlarmLOP	1.3.6.1.4.1.164.6.1.12.0.20			This trap indicates Loss of Pointer.
NTF atmAceAlarmLOS	1.3.6.1.4.1.164.6.1.12.0.16			This trap indicates Loss Of Signal.
NTF atmAceAlarmPathAIS	1.3.6.1.4.1.164.6.1.12.0.22			This trap indicates Path AIS.
NTF atmAceAlarmPathBIP	1.3.6.1.4.1.164.6.1.12.0.27			This trap indicates Path Bit Interleave Parity.
NTF atmAceAlarmPathFEBE	1.3.6.1.4.1.164.6.1.12.0.29			This trap indicates Path Far End Block Error.
NTF atmAceAlarmPathRDI	1.3.6.1.4.1.164.6.1.12.0.24			This trap indicates Path RDIand Path RAI(Yellow) for DS1 interfaces.
NTF atmAceAlarmPlcpBIP	1.3.6.1.4.1.164.6.1.12.0.32			This trap indicates T3 Plcp Bit Interleave Parity.
NTF atmAceAlarmPlcpFEBE	1.3.6.1.4.1.164.6.1.12.0.33			This trap indicates T3 Plcp Far End Block Error.
NTF atmAceAlarmPlcpLOF	1.3.6.1.4.1.164.6.1.12.0.30			This trap indicates T3 PLCP Loss Of Frame.
NTF atmAceAlarmPlcpP1P2	1.3.6.1.4.1.164.6.1.12.0.34			This trap indicates T3 Plcp Parity errors in P1/P2 bytes.
NTF atmAceAlarmPlcpYELLOW	1.3.6.1.4.1.164.6.1.12.0.31			This trap indicates T3 Plcp Yellow.
NTF atmAceAlarmSectionBIP	1.3.6.1.4.1.164.6.1.12.0.25			This trap indicates Section Bit Interleave Parity.
NTF atmAceAlarmSLM	1.3.6.1.4.1.164.6.1.12.0.19			This trap indicates Signal Line Mismatch.
NTF atmAceAlarmTrap	1.3.6.1.4.1.164.12.3.0.2			The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm. An active alarm state exists if: 1) The atmInterfaceActiveAlarms vector is different than 0. 2) The atmNteAlarmVpTable contains entries. 3) The atmNteAlarmVcTable contains entries. The trap is also sent when a transition into the no alarm state occurs. The second variable will be atmInterfaceActiveAlarms to indicate the kind of the alarm. The trap is not sent more than once in a 10 second interval.
NTF atmAceAlarmUAS	1.3.6.1.4.1.164.6.1.12.0.35			This trap is sent upon UAS start or end per port.
NTF atmAceAlarmVcAISReception	1.3.6.1.4.1.164.6.1.12.0.57			This trap indicates AIS Reception on a VC.
NTF atmAceAlarmVcContinuityLoss	1.3.6.1.4.1.164.6.1.12.0.56			This trap indicates Loss of Continuity Check on a VC Connection.
NTF atmAceAlarmVcErroredCells	1.3.6.1.4.1.164.6.1.12.0.59			This trap indicates Errored Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcGCRAViolation	1.3.6.1.4.1.164.6.1.12.0.65			This trap indicates GCRA violation on a VC Connection reported by UPC device.
NTF atmAceAlarmVcLoopback	1.3.6.1.4.1.164.6.1.12.0.64			This trap is sent upon OAM LoopBack fail status per VC.
NTF atmAceAlarmVcLostCells	1.3.6.1.4.1.164.6.1.12.0.60			This trap indicates Lost Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcMisinsertedCells	1.3.6.1.4.1.164.6.1.12.0.61			This trap indicates Misinserted Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcRDIReception	1.3.6.1.4.1.164.6.1.12.0.58			This trap indicates RDI Reception on a VC Connection.
NTF atmAceAlarmVcUAS	1.3.6.1.4.1.164.6.1.12.0.63			This trap is sent upon UAS start or end per VC.
NTF atmAceAlarmVcUnexpectedCell	1.3.6.1.4.1.164.6.1.12.0.62			This trap indicates an unexpected cell from user or network port.
NTF atmAceAlarmVpAISReception	1.3.6.1.4.1.164.6.1.12.0.41			This trap indicates AIS Reception on a VP Connection.
NTF atmAceAlarmVpContinuityLoss	1.3.6.1.4.1.164.6.1.12.0.40			This trap indicates Loss of Continuity Check on a VP Connection.
NTF atmAceAlarmVpErroredCells	1.3.6.1.4.1.164.6.1.12.0.43			This trap indicates Errored Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpGCRAViolation	1.3.6.1.4.1.164.6.1.12.0.48			This trap indicates GCRA violation on a VP Connection reported by UPC device.
NTF atmAceAlarmVpLoopback	1.3.6.1.4.1.164.6.1.12.0.47			This trap is sent upon OAM LoopBack fail status per VP.
NTF atmAceAlarmVpLostCells	1.3.6.1.4.1.164.6.1.12.0.44			This trap indicates Lost Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpMisinsertedCells	1.3.6.1.4.1.164.6.1.12.0.45			This trap indicates Misinserted Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpRDIReception	1.3.6.1.4.1.164.6.1.12.0.42			This trap indicates RDI Reception on a VP Connection.
NTF atmAceAlarmVpUAS	1.3.6.1.4.1.164.6.1.12.0.46			This trap is sent upon UAS start or end per VP.
NTF atmAceDateAndTimeRequest	1.3.6.1.4.1.164.6.1.12.0.8			This trap is sent upon restart. Upon recieving this trap the NMS will set the device's date and time. This trap's purpose is to fix a problem in ACE2002, ACE-2002E, ACE-202. The problem is that the Date and Time is stored in the NVRAM, and when the NVRAM's battery is empty, the device loses this information.
NTF atmAceHwFailure	1.3.6.1.4.1.164.6.1.12.0.37			This trap is sent upon HW failure per port.
NTF atmAceModuleChangeTrap	1.3.6.1.4.1.164.12.3.0.3			The trap is sent every time a module is changed (Hot swapping). The second variable will be atmNteCardType to indicate the type of card that was inserted. The value empty(255) indicates that a card was taken out.
NTF atmAceModuleMismatchTrap	1.3.6.1.4.1.164.12.3.0.5			The trap is sent upon starting or stopping of a module mismatch state. A possible mismatch is when the inserted module is other than the programmed one.
NTF atmAceRedundancyTrap	1.3.6.1.4.1.164.12.3.0.4			The trap is sent upon change in link as a result of redundancy. The ifIndex parameter indicates the current active link.
NTF atmAceStatusChange	1.3.6.1.4.1.164.12.3.0.1			The trap is sent every time there is a change in the state of one of the LEDs.
NTF atmAceSystemTrap	1.3.6.1.4.1.164.6.1.12.0.6			This trap alerts of major problems in the device.
NTF atmAceUnavailableBwTrap	1.3.6.1.4.1.164.6.1.12.0.38			This trap is sent when Bandwidth allocation is > max possible value for the installed card. For ACE2002 this trap will be sent for the following cases: Card insertion - if the total Input and/or Output Bandwidth is over allocated, then the specific card rate will be set to 0 and this trap will be sent with the Input/Output rates values. Upgrade from former version - when an over allocated Bandwidth is detected, this trap will be sent with atmConfIfInputRate=atmConfIfOutputRate=0xFFFFFFFF.
atmAlarmForwardingEntry	1.3.6.1.4.1.164.12.3.1.1.32.1		not-accessible	Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.
atmAlarmForwardingTable	1.3.6.1.4.1.164.12.3.1.1.32		not-accessible	The Alarm Forwarding Mechanism will be operated for this table entries.
atmGen	1.3.6.1.4.1.164.12.2
atmGenSysCxRefEntry	1.3.6.1.4.1.164.12.2.2.1.5.1		not-accessible	The entries will be added by the agent upon an entry addition in the referenced tables (TD table, FR Descriptor etc.)
atmGenSysCxRefTable	1.3.6.1.4.1.164.12.2.2.1.5		not-accessible	A Cross Reference table. The table maintains an index of an object which is also the table index, and a counter that indicates how many times this object was referenced. When using this table for more than one referenced table, which uses the same range of indexes, then the index should be shifted by a unique offset per table. In ACE2002 this table is used for TD and for FR Desc. Thus, the index for FR Descriptor is: FR Descriptor index + offset. The offset is described in the ACE2002 NMS SRS.
atmGenSysGen	1.3.6.1.4.1.164.12.2.2.1
atmGenSysLogEntry	1.3.6.1.4.1.164.12.2.2.1.3.1		not-accessible	An entry in table.
atmGenSysLogTable	1.3.6.1.4.1.164.12.2.2.1.3		not-accessible	A copy of the log buffer.
atmGenSysSelfTestEntry	1.3.6.1.4.1.164.12.2.2.1.1.1		not-accessible	An entry in table.
atmGenSysSelfTestTable	1.3.6.1.4.1.164.12.2.2.1.1		not-accessible	A table containing the results of the initial testing of the device.
atmGenSystem	1.3.6.1.4.1.164.12.2.2
atmIfCurrentEntry	1.3.6.1.4.1.164.12.2.1.1.2.1		not-accessible	An entry in the ATM interface Current table.
atmIfCurrentTable	1.3.6.1.4.1.164.12.2.1.1.2		not-accessible	The ATM interface Current table.
atmIfDataEntry	1.3.6.1.4.1.164.12.2.1.1.1.1		not-accessible	An entry in the ATM interface Data table.
atmIfDataTable	1.3.6.1.4.1.164.12.2.1.1.1		not-accessible	The ATM interface Data table.
atmIfIntervalEntry	1.3.6.1.4.1.164.12.2.1.1.3.1		not-accessible	An entry in the ATM interface Interval table.
atmIfIntervalTable	1.3.6.1.4.1.164.12.2.1.1.3		not-accessible	The ATM interface Interval table.
atmIfPerformance	1.3.6.1.4.1.164.12.2.1.1
atmIntervalDateEntry	1.3.6.1.4.1.164.12.2.1.3.1		not-accessible	The date & time for the given interval.
atmIntervalDateTable	1.3.6.1.4.1.164.12.2.1.3		not-accessible	The agent will keep in this group the date & time corresponding to each interval.
atmLoopbackVcEntry	1.3.6.1.4.1.164.12.3.2.2.2.1		not-accessible	An entry in table.
atmLoopbackVcIvlEntry	1.3.6.1.4.1.164.12.3.2.2.4.1		not-accessible	An entry in table.
atmLoopbackVcIvlTable	1.3.6.1.4.1.164.12.3.2.2.4		not-accessible	This table contains parameters for an OAM VC loopback test.
atmLoopbackVcTable	1.3.6.1.4.1.164.12.3.2.2.2		not-accessible	This table contains parameters for an OAM VC loopback test.
atmLoopbackVpEntry	1.3.6.1.4.1.164.12.3.2.2.1.1		not-accessible	An entry in table atmLoopbackVpTable.
atmLoopbackVpIvlEntry	1.3.6.1.4.1.164.12.3.2.2.3.1		not-accessible	An entry in table.
atmLoopbackVpIvlTable	1.3.6.1.4.1.164.12.3.2.2.3		not-accessible	This table contains parameters for an OAM VP loopback test, according interval number.
atmLoopbackVpTable	1.3.6.1.4.1.164.12.3.2.2.1		not-accessible	This table contains parameters for an OAM VP loopback test.
atmNte	1.3.6.1.4.1.164.12.3
atmNteAlarmIfEntry	1.3.6.1.4.1.164.12.3.2.1.2.1		not-accessible	An entry in the interface Alarm table.
atmNteAlarmIfTable	1.3.6.1.4.1.164.12.3.2.1.2		not-accessible	The interface Alarm table.
atmNteAlarmVcEntry	1.3.6.1.4.1.164.12.3.2.1.6.1		not-accessible	An entry in the ATM VC Alarm table. ifIndex of the ATM layer.
atmNteAlarmVcTable	1.3.6.1.4.1.164.12.3.2.1.6		not-accessible	The ATM VC Alarm table.
atmNteAlarmVpEntry	1.3.6.1.4.1.164.12.3.2.1.5.1		not-accessible	An entry in the ATM VP Alarm table. ifIndex of the ATM layer.
atmNteAlarmVpTable	1.3.6.1.4.1.164.12.3.2.1.5		not-accessible	The ATM VP Alarm table.
atmNteConfCAC	1.3.6.1.4.1.164.12.3.1.1.10
atmNteConfIfEntry	1.3.6.1.4.1.164.12.3.2.1.1.1		not-accessible	An entry in the Physical interface configuration table. The ifIndex is of the lowest physical layer.
atmNteConfIfTable	1.3.6.1.4.1.164.12.3.2.1.1		not-accessible	The Physical interface configuration table.
atmNteConfOam	1.3.6.1.4.1.164.12.3.1.1.9
atmNteConfOamAddressing	1.3.6.1.4.1.164.12.3.1.1.9.3
atmNteConfOamIfEntry	1.3.6.1.4.1.164.12.3.1.1.9.4.1		not-accessible	.
atmNteConfOamIfTable	1.3.6.1.4.1.164.12.3.1.1.9.4		not-accessible	OAM support per ATM interface.
atmNteConfOamTransmission	1.3.6.1.4.1.164.12.3.1.1.9.2
atmNteConfVpEntry	1.3.6.1.4.1.164.12.3.2.1.3.1		not-accessible	An entry in the ATM VP configuration table. ifIndex of the ATM layer.
atmNteConfVpTable	1.3.6.1.4.1.164.12.3.2.1.3		not-accessible	The ATM VP configuration table. The table is an extension to the atmVplTable of RFC-1695.
atmNteEvents	1.3.6.1.4.1.164.12.3.0			The events for RAD ATM products.
atmNteHostIfEntry	1.3.6.1.4.1.164.12.3.1.1.11.1		not-accessible	.
atmNteHostIfTable	1.3.6.1.4.1.164.12.3.1.1.11		not-accessible	Host IP interface table.
atmNteIdEntry	1.3.6.1.4.1.164.12.3.1.2.1.1		not-accessible	.
atmNteIdTable	1.3.6.1.4.1.164.12.3.1.2.1		not-accessible	The IDs of the cards and of the system.
atmNteLoopback	1.3.6.1.4.1.164.12.3.2.2
atmNteManagerEntry	1.3.6.1.4.1.164.12.3.1.1.1.1		not-accessible	A single manager and the PVC for receiving traps.
atmNteManagerTable	1.3.6.1.4.1.164.12.3.1.1.1		not-accessible	The Manager Table includes all the NMSs that receive traps from this agent. A single manager can receive traps on more than one PVC. The agent will set implicitly the correct ifIndex, VPI, VCI values to all relevant entries in the table when the user changes them for one of the PVCs.
atmNteMdl	1.3.6.1.4.1.164.12.3.3
atmNteMdlConfig	1.3.6.1.4.1.164.12.3.3.1
atmNteMdlConfigEntry	1.3.6.1.4.1.164.12.3.3.1.1.1		not-accessible	There is an entry in this table just for those modules that have parameters that are relevant to module level only.
atmNteMdlConfigTable	1.3.6.1.4.1.164.12.3.3.1.1		not-accessible	Module configuration table.
atmNteOamEntry	1.3.6.1.4.1.164.12.3.1.1.26.1		not-accessible	An entry in the OAM table. Each entry in this table will indicate a special OAM.
atmNteOamTable	1.3.6.1.4.1.164.12.3.1.1.26		not-accessible	This table is a static table, which is created by agent once upon initialization. The created entries are actually, only the supported OAM features. This table enables addition of new features by adding new entries rather than adding scalar parameters. An OAM feature is defined by the indexes values combination.
atmNtePM	1.3.6.1.4.1.164.12.3.2.3
atmNteProtection	1.3.6.1.4.1.164.12.3.1.1.8
atmNtePrt	1.3.6.1.4.1.164.12.3.2
atmNtePrtConfig	1.3.6.1.4.1.164.12.3.2.1
atmNteSys	1.3.6.1.4.1.164.12.3.1
atmNteSysConfig	1.3.6.1.4.1.164.12.3.1.1
atmNteSysInfo	1.3.6.1.4.1.164.12.3.1.2
atmPerfHistory	1.3.6.1.4.1.164.12.2.1
atmPvcPerformance	1.3.6.1.4.1.164.12.2.1.2
atmSysConfigCellTest	1.3.6.1.4.1.164.12.3.1.1.33
atmSysIntervalEntry	1.3.6.1.4.1.164.12.3.1.2.8.2.1		not-accessible	.
atmSysIntervalTable	1.3.6.1.4.1.164.12.3.1.2.8.2		not-accessible	The system level Interval table.
atmSysStats	1.3.6.1.4.1.164.12.3.1.2.8
atmTrafficDescrParamXEntry	1.3.6.1.4.1.164.12.3.1.1.38.1		not-accessible	An entry in the table.
atmTrafficDescrParamXTable	1.3.6.1.4.1.164.12.3.1.1.38		not-accessible	An Augment to ATM Traffic Descriptor Parameter Table (atmTrafficDescrParamTable in ATM-MIB; RFC-2515).
atmVcCrossConnectExtenEntry	1.3.6.1.4.1.164.12.3.1.1.35.1		not-accessible	An entry in the table.
atmVcCrossConnectExtenTable	1.3.6.1.4.1.164.12.3.1.1.35		not-accessible	An extension to the ATM VC Cross Connect table (RFC2515 - atmVcCrossConnectTable).
atmVcCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.2.1.1		not-accessible	An entry in the ATM VC Current table.
atmVcCurrentTable	1.3.6.1.4.1.164.12.2.1.2.2.1		not-accessible	The ATM VC Current table.
atmVcIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.2.3.1		not-accessible	An entry in the ATM Vc Interval table.
atmVcIntervalTable	1.3.6.1.4.1.164.12.2.1.2.2.3		not-accessible	The ATM Vc Interval table.
atmVcPerformance	1.3.6.1.4.1.164.12.2.1.2.2
atmVcPMCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.2.2.1		not-accessible	An entry in the ATM VC Current table for Performance Management.
atmVcPMCurrentTable	1.3.6.1.4.1.164.12.2.1.2.2.2		not-accessible	The ATM VC Current table for Performance Management.
atmVcPmEntry	1.3.6.1.4.1.164.12.3.2.3.2.1		not-accessible	An entry in table.
atmVcPMIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.2.4.1		not-accessible	An entry in the ATM Vc Interval table for Performance Management.
atmVcPMIntervalTable	1.3.6.1.4.1.164.12.2.1.2.2.4		not-accessible	The ATM Vc Interval table for Performance Management.
atmVcPMQoSEntry	1.3.6.1.4.1.164.12.2.1.2.2.7.1		not-accessible	An entry in the VC PM QoS table.
atmVcPMQoSTable	1.3.6.1.4.1.164.12.2.1.2.2.7		not-accessible	The PM VC QoS table.
atmVcPmTable	1.3.6.1.4.1.164.12.3.2.3.2		not-accessible	This table contains parameters for VC performance monitoring.
atmVcQoSEntry	1.3.6.1.4.1.164.12.2.1.2.2.6.1		not-accessible	An entry in the ATM VP table.
atmVcQoSTable	1.3.6.1.4.1.164.12.2.1.2.2.6		not-accessible	The ATM VP QoS table.
atmVcShaperStatEntry	1.3.6.1.4.1.164.12.2.1.2.2.8.1		not-accessible	An entry in the ATM VC shaper statistics table.
atmVcShaperStatTable	1.3.6.1.4.1.164.12.2.1.2.2.8		not-accessible	The ATM VC shaper statistics table.
atmVpCrossConnectExtenEntry	1.3.6.1.4.1.164.12.3.1.1.34.1		not-accessible	An entry in the table.
atmVpCrossConnectExtenTable	1.3.6.1.4.1.164.12.3.1.1.34		not-accessible	An extension to the ATM VP Cross Connect table (RFC2515 - atmVpCrossConnectTable).
atmVpCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.1.1.1		not-accessible	An entry in the ATM VP Current table.
atmVpCurrentTable	1.3.6.1.4.1.164.12.2.1.2.1.1		not-accessible	The ATM VP Current table.
atmVpIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.1.3.1		not-accessible	An entry in the ATM Vp Interval table.
atmVpIntervalTable	1.3.6.1.4.1.164.12.2.1.2.1.3		not-accessible	The ATM Vp Interval table.
atmVpPerformance	1.3.6.1.4.1.164.12.2.1.2.1
atmVpPMCurrentEntry	1.3.6.1.4.1.164.12.2.1.2.1.2.1		not-accessible	An entry in the ATM VP Current table for Performance Management.
atmVpPMCurrentTable	1.3.6.1.4.1.164.12.2.1.2.1.2		not-accessible	The ATM VP Current table for Performance Management.
atmVpPmEntry	1.3.6.1.4.1.164.12.3.2.3.1.1		not-accessible	An entry in table.
atmVpPMIntervalEntry	1.3.6.1.4.1.164.12.2.1.2.1.4.1		not-accessible	An entry in the ATM Vp Interval table for Performance Management.
atmVpPMIntervalTable	1.3.6.1.4.1.164.12.2.1.2.1.4		not-accessible	The ATM Vp Interval table for Performance Management.
atmVpPMQoSEntry	1.3.6.1.4.1.164.12.2.1.2.1.6.1		not-accessible	.
atmVpPMQoSTable	1.3.6.1.4.1.164.12.2.1.2.1.6		not-accessible	The PM VP QoS table.
atmVpPmTable	1.3.6.1.4.1.164.12.3.2.3.1		not-accessible	This table contains parameters for VP performance monitoring.
atmVpQoSEntry	1.3.6.1.4.1.164.12.2.1.2.1.5.1		not-accessible	.
atmVpQoSTable	1.3.6.1.4.1.164.12.2.1.2.1.5		not-accessible	The VP QoS table.
atmVpShaperStatEntry	1.3.6.1.4.1.164.12.2.1.2.1.7.1		not-accessible	An entry in the ATM VP shaper statistics table.
atmVpShaperStatTable	1.3.6.1.4.1.164.12.2.1.2.1.7		not-accessible	The ATM VP shaper statistics table.
autoFileTransfer	1.3.6.1.4.1.164.6.2.12.13
autoFileTransferEntry	1.3.6.1.4.1.164.6.2.12.13.1.1		not-accessible	An entry in the table.
autoFileTransferTable	1.3.6.1.4.1.164.6.2.12.13.1		not-accessible	Scheduling configuration table for Agent initiated file transfer.
bdbandConfig	1.3.6.1.4.1.164.3.1.6.8.1
bitMappingEntry	1.3.6.1.4.1.164.6.2.38.1		not-accessible	Each entry in the table describes a correlation of a bit location to an interface. For ACE-2002 - Upon creation of a new LAN VCC the agent will add an entry to this table that will define the bit location for that VCC.
bitMappingTable	1.3.6.1.4.1.164.6.2.38		not-accessible	This table maps bits of an octet string to an interface. For ACE-2002 this table is used to map bits of VLAN port lists to LAN VCC's. This table is the opposite view of the xcTable for xcBitMapping. It is used to ease the bit translation for the NMS.
broadbandIf	1.3.6.1.4.1.164.3.1.6.8
NTF bundleConnectionStatusTrap	1.3.6.1.4.1.164.6.1.3.0.15			This trap is sent upon any change in the connectivity status of a Bundle (ip2IfOperStatus). The ifAlias index is the ifIndex of the bundle that its status has been changed.
NTF channelOperStatusTrap	1.3.6.1.4.1.164.6.1.3.0.9			This trap is sent upon any change in one or more channels.
chasWanGen	1.3.6.1.4.1.164.3.1.1
NTF clkSrcChangeTrap	1.3.6.1.4.1.164.6.1.0.10			This trap is sent upon any change in Clock Source.
cmprAgnGen	1.3.6.1.4.1.164.3.1.2.3
cmprEntry	1.3.6.1.4.1.164.3.3.4.1.1		not-accessible	An entry in table.
cmprMdlGen	1.3.6.1.4.1.164.3.1.3.3
cmprPrtGen	1.3.6.1.4.1.164.3.1.4.3
cmprTable	1.3.6.1.4.1.164.3.3.4.1		not-accessible	A table.
cnfgAgnGen	1.3.6.1.4.1.164.3.1.2.2
NTF cnfgFlipTrap	1.3.6.1.4.1.164.3.2.0.3			This trap is sent upon change of the active Configuration DB. Attached, is the new active Configuration no.
cnfgMdlGen	1.3.6.1.4.1.164.3.1.3.2
cnfgMdlMux	1.3.6.1.4.1.164.3.2.2.1
cnfgPrtGen	1.3.6.1.4.1.164.3.1.4.2
cnfgPrtMux	1.3.6.1.4.1.164.3.2.3.2
NTF cnfgUpdateTrap	1.3.6.1.4.1.164.3.3.0.6			This trap is sent upon change of the active Configuration DB.
cosProfileEntry	1.3.6.1.4.1.164.6.3.10.1		not-accessible	A conceptual row where each row contains one CoS attributes.
cosProfileTable	1.3.6.1.4.1.164.6.3.10		not-accessible	Class of Service Profile table. Each profile holds a priority method, and a mappring function that maps the priority values (range according to the method) into CoS values.
dacsMux	1.3.6.1.4.1.164.3.3
NTF dacsMuxAlarmsTrap	1.3.6.1.4.1.164.3.3.0.2			This trap is sent when an alarm occurs.
dacsMuxEvents	1.3.6.1.4.1.164.3.3.0			The events for DACS MUX.
dhcpClientEntry	1.3.6.1.4.1.164.11.7.2.2.1.6.1		not-accessible	DHCP Client parameters per entry of the DHCP Client table.
dhcpClientTable	1.3.6.1.4.1.164.11.7.2.2.1.6		not-accessible	A list of DHCP client entries.
dhcpIfClientEntry	1.3.6.1.4.1.164.11.7.2.2.1.7.1		not-accessible	DHCP Clients per entry of the DHCP Interface Client table.
dhcpIfClientTable	1.3.6.1.4.1.164.11.7.2.2.1.7		not-accessible	DHCP client entries for each Interface.
dhcpPoolAllocEntry	1.3.6.1.4.1.164.11.7.2.2.1.3.1		not-accessible	DHCP Pool Allocation parameters per entry of the DHCP Pool Allocation table.
dhcpPoolAllocTable	1.3.6.1.4.1.164.11.7.2.2.1.3		not-accessible	A list of DHCP Pool Allocation entries. Each entry (row) consist of a single IP Address belonging to DHCP pool whose lowest IP address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing, or may already be leased (in use) by Host it's MacAddress is dhcpPoolAllocMacAddress. Time left for leasing period is indicated by dhcpPoolAllocTimeLeft. All posible statuses of IP address are indicated and controlled by dhcpPoolAllocFlags
dhcpRelayEntry	1.3.6.1.4.1.164.11.7.2.2.1.4.1		not-accessible	DHCP Relay parameters per entry of the DHCP relay table.
dhcpRelayTable	1.3.6.1.4.1.164.11.7.2.2.1.4		not-accessible	A list of DHCP relay entries.
diverseIfWanGen	1.3.6.1.4.1.164.3.1.6
dot1agXCfmMdEntry	1.3.6.1.4.1.164.3.1.6.1.3.8.1		not-accessible	The Maintenance Domain table entry.
dot1agXCfmMdTable	1.3.6.1.4.1.164.3.1.6.1.3.8		not-accessible	The Maintenance Domain table. Each row in the table represents a different maintenance association.
dot1agXCfmMepDbEntry	1.3.6.1.4.1.164.3.1.6.1.3.10.1		not-accessible	The MEP Database table entry.
dot1agXCfmMepDbTable	1.3.6.1.4.1.164.3.1.6.1.3.10		not-accessible	The MEP DB table
dot1agXCfmMepEntry	1.3.6.1.4.1.164.3.1.6.1.3.9.1		not-accessible	The MEP table entry
dot1agXCfmMepTable	1.3.6.1.4.1.164.3.1.6.1.3.9		not-accessible	The Maintenance Association End Point (MEP) table.
dot3OamDescrEntry	1.3.6.1.4.1.164.3.1.6.1.6.1.1		not-accessible	Each entry corresponds to a single OAM EFM Descriptor (profile). Each Descriptor contains a set of OAM EFM Link configuration parameters. The configuration parameters are applied to the OAM EFM Links referencing this Descriptor (see dot3OamXDescrId object). Descriptors may be created/deleted using the row creation/deletion mechanism via dot3OamDescrRowStatus. If an active entry is referenced in dot3OamXDescrId, the entry MUST remain active until all references are removed.
dot3OamDescrTable	1.3.6.1.4.1.164.3.1.6.1.6.1		not-accessible	This table supports definitions of Descriptors (profiles) of OAM EFM Links.
dot3OamEvents	1.3.6.1.4.1.164.3.1.6.1.6.0
NTF dot3OamOperStatusChange	1.3.6.1.4.1.164.3.1.6.1.6.0.1			This trap is sent when OAM EFM Link goes Up or Down. Up - is considered when dot3OamOperStatus value changes to operational(9) from any other value. Down - is considered when dot3OamOperStatus value changes from operational(9) to any other value.
NTF dot3OamPeerEvent	1.3.6.1.4.1.164.3.1.6.1.6.0.2			This trap is sent when value of dot3OamXPeerState changes from any value to one of the following values: linkFault, dyingGasp, criticalEvent. This trap has no recovery (clearing value).
dot3OamXEntry	1.3.6.1.4.1.164.3.1.6.1.6.2.1		not-accessible	An entry in dot3OamXTable.
dot3OamXTable	1.3.6.1.4.1.164.3.1.6.1.6.2		not-accessible	This table is an extension of dot3OamTable of standard DOT3-OAM-MIB.
NTF ds1AisSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.10			This trap indicates near end (Local) Loss of Frame Alignment (Sync Loss), caused by the reception of AIS at the user DS1 interface.
NTF ds1AisTrap	1.3.6.1.4.1.164.3.1.6.4.0.11			This trap indicates AIS being received at the user DS1 interface.
NTF ds1BpvErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.4			This trap indicates a Bipolar Violation (BPV) error has been detected at the user DS1 interface.
NTF ds1Crc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.6			This trap indicates that a frame with CRC-4 error has been detected at the user DS1 interface.
NTF ds1ExcessiveBpvTrap	1.3.6.1.4.1.164.3.1.6.4.0.5			This trap indicates excessive number of Bipolar Violation errors (BPV) detected by the user DS1 interface
NTF ds1ExcessiveCrc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.16			This trap indicates that the error rate detected on the CRC-4 bits at the user DS1 interface, is high.
NTF ds1ExcessiveErrorRatioTrap	1.3.6.1.4.1.164.3.1.6.4.0.7			This trap indicates that the error rate, detected at the user DS1 interface, on the frame synchronization bits is high, as defined by ITU-T Rec. G.732.
NTF ds1ExcessiveFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.15			This trap indicates that the number of Frame Slips detected at the user DS1 interface, during the last minute exceeds threshold. For LA-110, threshold value is 10. This usually indicates timing problems (incorrect selection of timing reference) on the user DS1.
NTF ds1ExcessiveLocalMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.17			This trap indicates that the number of local Loss of Multiframe Alignment events, detected at the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveLocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.20			This trap indicates that the number of Loss of local Synchronization alarms reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.18			This trap indicates that the number of Loss of multiframe alignment events reported by the remote unit connected to the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.19			This trap indicates that the number of far end (remote) Loss of Synchronization alarms, reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
ds1Interface	1.3.6.1.4.1.164.3.1.6.4
NTF ds1LinkFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.3			This trap indicates that a Frame Slip occurred at the user DS1 interface. This usually indicates timing problems (incorrect selection of timing reference), on the user DS1 link.
NTF ds1LocalLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.14			This trap indicates that a local loopback has been activated on the user port.
NTF ds1LocalMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.1			This trap indicates near end (Local) Loss of Multiframe Alignment, of the user E1 interface.
NTF ds1LocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.9			This trap indicates near end (Local) Loss of Frame Alignment failure (Sync Loss), of the user DS1 interface
NTF ds1NetworkRemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.12			This trap indicates that a remote loopback has been activated, on the local uplink interface.
NTF ds1RemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.13			This trap indicates that a remote loopback has been activated, on the local user port.
NTF ds1RemoteMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.2			This trap indicates that the far end (remote) unit, connected to the user E1 interface, reports Loss of Multiframe Alignment.
NTF ds1RemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.8			This trap indicates that the far-end (remote) unit, connected to user DS1 interface, reports Loss of Frame Alignment (Sync Loss).
NTF ds1SignalLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.21			This trap indicates Signal Loss. (possible reason - cable disconnection. etc.)
ds3Interface	1.3.6.1.4.1.164.3.1.6.3
dscpMapping	1.3.6.1.4.1.164.6.3.2
dscpMappingEntry	1.3.6.1.4.1.164.6.3.2.1.1		not-accessible	An entry in dscpMappingTable.
dscpMappingTable	1.3.6.1.4.1.164.6.3.2.1		not-accessible	Mapping of DSCP value to a regenerated priority level.
dsx1DataStreamStatEntry	1.3.6.1.4.1.164.3.1.6.4.1.5.1		not-accessible	An entry in the DS1 Data Stream Statistics table.
dsx1DataStreamStatTable	1.3.6.1.4.1.164.3.1.6.4.1.5		not-accessible	The DS1 Data Stream Statistics table.
dsx1XConfigEntry	1.3.6.1.4.1.164.3.1.6.4.2.1		not-accessible	An entry containing additional configuration parameters.
dsx1XConfigTable	1.3.6.1.4.1.164.3.1.6.4.2		not-accessible	An extension to the DS1 Configuration table.
dsx1XCurrentEntry	1.3.6.1.4.1.164.3.1.6.4.1.2.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
dsx1XCurrentTable	1.3.6.1.4.1.164.3.1.6.4.1.2		not-accessible	A list of current statistics entries. This table contains additional objects for the current table.
dsx1XIntervalEntry	1.3.6.1.4.1.164.3.1.6.4.1.3.1		not-accessible	An entry containing additional statistical counters applicable to a particular interval table.
dsx1XIntervalTable	1.3.6.1.4.1.164.3.1.6.4.1.3		not-accessible	A list of Interval entries. This table contains additional objects for the interval table.
dsx1XTotalEntry	1.3.6.1.4.1.164.3.1.6.4.1.4.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
dsx1XTotalTable	1.3.6.1.4.1.164.3.1.6.4.1.4		not-accessible	A list of Total statistics entries. This table contains additional objects for the Total table.
dsx3MappingEntry	1.3.6.1.4.1.164.3.1.6.3.3.1		not-accessible	An entry in the DS3 mapping table.
dsx3MappingTable	1.3.6.1.4.1.164.3.1.6.3.3		not-accessible	The DS3/E3 mapping table associates DS3/E3 channels with logical or physical interfaces. For example, consider a DS3 device with 16 T1's and 1 VCG. There are 28 logical/internal channels, numbered 1 through 28 but only 17 are actually connected. We might describe the allocation of channels, in the dsx3MappingTable, as follows: dsx3MappingIfIndex.1. 1 = 1001 dsx3MappingIfIndex.1.15 = 1015 dsx3MappingIfIndex.1. 2 = 1002 dsx3MappingIfIndex.1.16 = 1016 dsx3MappingIfIndex.1. 3 = 1003 dsx3MappingIfIndex.1.17 = 1017 dsx3MappingIfIndex.1. 4 = 1004 dsx3MappingIfIndex.1.18 = 0 dsx3MappingIfIndex.1. 5 = 1005 dsx3MappingIfIndex.1.19 = 0 dsx3MappingIfIndex.1. 6 = 1006 dsx3MappingIfIndex.1.20 = 0 dsx3MappingIfIndex.1. 7 = 1007 dsx3MappingIfIndex.1.21 = 0 dsx3MappingIfIndex.1. 8 = 1008 dsx3MappingIfIndex.1.22 = 0 dsx3MappingIfIndex.1. 9 = 1009 dsx3MappingIfIndex.1.23 = 0 dsx3MappingIfIndex.1.10 = 1010 dsx3MappingIfIndex.1.24 = 0 dsx3MappingIfIndex.1.11 = 1011 dsx3MappingIfIndex.1.25 = 0 dsx3MappingIfIndex.1.12 = 1012 dsx3MappingIfIndex.1.26 = 0 dsx3MappingIfIndex.1.13 = 1013 dsx3MappingIfIndex.1.27 = 0 dsx3MappingIfIndex.1.14 = 1014 dsx3MappingIfIndex.1.28 = 0 Note that in the case above all channels are mapped to one T3 port with ifIndex = 1. The Channels 1...28 are represented via the 2nd index. The values of 1001...1016 are the T1 interface ifIndexes. The value of 1017 is the ifIndex of the VCG. Unconnected channels have a value of 0.
dsx3XConfigEntry	1.3.6.1.4.1.164.3.1.6.3.2.1		not-accessible	An entry containing additional configuration parameters.
dsx3XConfigTable	1.3.6.1.4.1.164.3.1.6.3.2		not-accessible	An extension to the DS3 Configuration table.
NTF enrollmentTrap	1.3.6.1.4.1.164.6.1.0.12			This trap is a periodically trap, which sent to manager untill Agent get any response (Get or Set) from this manager.
ethIf	1.3.6.1.4.1.164.3.1.6.1
ethIfCurrentEntry	1.3.6.1.4.1.164.3.1.6.1.2.1.1		not-accessible	An entry in the Ethernet Current table.
ethIfCurrentTable	1.3.6.1.4.1.164.3.1.6.1.2.1		not-accessible	The Ethernet Current table. When the index specifies the Ethernet interface (only), the counters are for an interval of 15 minutes.
ethIfEntry	1.3.6.1.4.1.164.3.1.6.1.1.1		not-accessible	An entry in table.
ethIfIntervalEntry	1.3.6.1.4.1.164.3.1.6.1.2.2.1		not-accessible	An entry in the Ethernet Interval table.
ethIfIntervalTable	1.3.6.1.4.1.164.3.1.6.1.2.2		not-accessible	The Ethernet Interval table. When ethIfIntervalIndex specifies the Ethernet interface (only), the counters are for an interval of 15 minutes.
NTF ethIfMacAccessViolation	1.3.6.1.4.1.164.3.1.6.1.7.0.1			This trap indicates that an Access Violation occurred.
ethIfMacLayer	1.3.6.1.4.1.164.3.1.6.1.7
ethIfMacLayerEvents	1.3.6.1.4.1.164.3.1.6.1.7.0
ethIfOamCfm	1.3.6.1.4.1.164.3.1.6.1.3
ethIfOamCfmEvents	1.3.6.1.4.1.164.3.1.6.1.3.0
ethIfOamEfm	1.3.6.1.4.1.164.3.1.6.1.6
ethIfPerfEntry	1.3.6.1.4.1.164.3.1.6.1.2.4.1		not-accessible	An entry in the Ethernet Performance table.
ethIfPerformance	1.3.6.1.4.1.164.3.1.6.1.2
ethIfPerfTable	1.3.6.1.4.1.164.3.1.6.1.2.4		not-accessible	The Ethernet Performance table.
ethIfRing	1.3.6.1.4.1.164.3.1.6.1.4
ethIfRingEntry	1.3.6.1.4.1.164.3.1.6.1.4.1.1		not-accessible	An entry in the table.
ethIfRingEvents	1.3.6.1.4.1.164.3.1.6.1.4.0
NTF ethIfRingStatusChange	1.3.6.1.4.1.164.3.1.6.1.4.0.1			This trap indicates that the status of the Ethernet Ring has been changed.
ethIfRingTable	1.3.6.1.4.1.164.3.1.6.1.4.1		not-accessible	Ethernet Ring Table.
ethIfSrcMacCtrlAddrEntry	1.3.6.1.4.1.164.3.1.6.1.7.2.1		not-accessible	An entry in the table.
ethIfSrcMacCtrlAddrTable	1.3.6.1.4.1.164.3.1.6.1.7.2		not-accessible	This table shows which MAC Addresses are permitted when the source MAC control is enabled and which non permitted MAC Addresses attempted to access the current interface. It contains static source MAC Addresses as well as learned MAC Addresses. The user can configure Static permitted source MAC Addresses via this table.
ethIfSrcMacCtrlEntry	1.3.6.1.4.1.164.3.1.6.1.7.1.1		not-accessible	An entry in the table.
ethIfSrcMacCtrlTable	1.3.6.1.4.1.164.3.1.6.1.7.1		not-accessible	This table supports source MAC addresses control parameters per interface. Source MAC control will be used mainly for security. Only packets with certain source MAC Addresses will be allowed to access the device. The source MAC addresses can be static or learned. The static addresses will be defined by the user in another table: ethIfSrcMacCtrlAddrTable. The learned addresses will exist in the ethIfSrcMacCtrlAddrTable as well.
ethIfStormEntry	1.3.6.1.4.1.164.3.1.6.1.5.1.1		not-accessible	An entry in the table.
ethIfStorming	1.3.6.1.4.1.164.3.1.6.1.5
ethIfStormTable	1.3.6.1.4.1.164.3.1.6.1.5.1		not-accessible	Ethernet Storming Table.
ethIfTable	1.3.6.1.4.1.164.3.1.6.1.1		not-accessible	A table.
NTF ethOamCfmDefectCondition	1.3.6.1.4.1.164.3.1.6.1.3.0.1			This trap indicates that a MEP has a persistent defect condition.
ethOamService	1.3.6.1.4.1.164.3.1.6.1.3.2
ethOamServiceEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.1.1		not-accessible	An entry in the table.
ethOamServiceTable	1.3.6.1.4.1.164.3.1.6.1.3.2.1		not-accessible	Service configuration table associated with Services running on a MEP.
ethOamSvcCurrentStatEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.2.1		not-accessible	Current Statistics per service
ethOamSvcCurrentStatTable	1.3.6.1.4.1.164.3.1.6.1.3.2.2		not-accessible	Service Current Statistics Table.
ethOamSvcIntervalEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.3.1		not-accessible	Interval Statistics per service
ethOamSvcIntervalTable	1.3.6.1.4.1.164.3.1.6.1.3.2.3		not-accessible	Service Interval Statistics Table.
ethOamSvcTotalEntry	1.3.6.1.4.1.164.3.1.6.1.3.2.4.1		not-accessible	Total Statistics per service
ethOamSvcTotalTable	1.3.6.1.4.1.164.3.1.6.1.3.2.4		not-accessible	ETH OAM Service Total (24H) Statistics Table.
evcCosEntry	1.3.6.1.4.1.164.6.3.7.1		not-accessible	An entry in table.
evcCosTable	1.3.6.1.4.1.164.6.3.7		not-accessible	This table defines mapping of Ethernet Virtual Connection (EVC) ID to Class of Service (CoS) ID
NTF failedLogin	1.3.6.1.4.1.164.6.1.0.25			This trap is sent when a user tried to Login via Terminal/Telnet/Web and failed. This trap is used when the device is located at End-User's premises while management is at Service Provider's premises.
fileTransfer	1.3.6.1.4.1.164.6.2.12
NTF flipDbChangeTrap	1.3.6.1.4.1.164.3.2.0.4			This trap is sent upon change of the active Flip tables (Flip DB).
flowMappingProfileEntry	1.3.6.1.4.1.164.6.3.9.1.1		not-accessible	Each entry in this table describes one Flow mapping profile with one of its Flow Mapping supported, according to the Priority order. The information includes a reference to a Flow Mapping index.
flowMappingProfileTable	1.3.6.1.4.1.164.6.3.9.1		not-accessible	This table holds flow mapping profiles.
genBridge	1.3.6.1.4.1.164.4.1
genDacsMux	1.3.6.1.4.1.164.3.3.4
gfp	1.3.6.1.4.1.164.6.2.55
gfpCnfgEntry	1.3.6.1.4.1.164.6.2.55.1.1		not-accessible	An entry in the GFP configuration table.
gfpCnfgTable	1.3.6.1.4.1.164.6.2.55.1		not-accessible	Configuration table for GFP (General Framing Protocol).
hostEntry	1.3.6.1.4.1.164.6.2.40.1		not-accessible	An entry in the Host Table. The hostParam1, hostParam2, and hostParam3 entries may have different use in different applications.
hostTable	1.3.6.1.4.1.164.6.2.40		not-accessible	Host interface table.
ifCreateEntry	1.3.6.1.4.1.164.6.2.35.1.1		not-accessible	An entry in the Interface Configuration table.
ifCreateTable	1.3.6.1.4.1.164.6.2.35.1		not-accessible	The Interface Configuration Table. This table enables to create interfaces of Entities.
ifPerfEntry	1.3.6.1.4.1.164.6.2.35.2.1.1		not-accessible	An entry in the Interface Performance Table.
ifPerfTable	1.3.6.1.4.1.164.6.2.35.2.1		not-accessible	Interface Performance Table. The propose of this table is to support statistics counters having 64 bit by using 2 parameters with syntax= Integer32. This is because SNMPv1 does not support Counter64 properly. For SNMPv3, ifPerfHCCounter (Counter64) may be supported.
ifTeQos	1.3.6.1.4.1.164.6.3.3
ifTeQosEntry	1.3.6.1.4.1.164.6.3.3.1.1		not-accessible	An entry in the TE QOS Interface table.
ifTeQosTable	1.3.6.1.4.1.164.6.3.3.1		not-accessible	The TE QOS Interface Table.
interfacePerformance	1.3.6.1.4.1.164.6.2.35.2
intSwdlEntry	1.3.6.1.4.1.164.6.2.12.10.1		not-accessible	An entry in table.
NTF intSwdlSlotFileMismatch	1.3.6.1.4.1.164.6.1.0.5			This notification is sent when the card in the chosen slot doesn't match the chosen file. The attached object indicates the File Name.
intSwdlTable	1.3.6.1.4.1.164.6.2.12.10		not-accessible	This parameters table is for internal Software down load. It also includes data about all files contained in the Object from which down-load is performed.
invNameXCEntry	1.3.6.1.4.1.164.6.2.41.1		not-accessible	An entry in the table.
invNameXCTable	1.3.6.1.4.1.164.6.2.41		not-accessible	Inverse Name XC Table. This table can be used to ease the search for a connection first index by the connection name.
ip2If	1.3.6.1.4.1.164.3.1.6.7
ip2IfCurrentStatEntry	1.3.6.1.4.1.164.3.1.6.7.10.1		not-accessible	IP Current Statistics per bundle
ip2IfCurrentStatTable	1.3.6.1.4.1.164.3.1.6.7.10		not-accessible	Channels (Bundles) Current Statistics Table.
ip2IfEntry	1.3.6.1.4.1.164.3.1.6.7.1.1		not-accessible	Application layer configuration per link
ip2IfIntervalStatEntry	1.3.6.1.4.1.164.3.1.6.7.11.1		not-accessible	IP Interval Statistics per bundle
ip2IfIntervalStatTable	1.3.6.1.4.1.164.3.1.6.7.11		not-accessible	Channels (Bundles) Interval Statistics Table.
ip2IfPortEntry	1.3.6.1.4.1.164.3.1.6.7.9.1		not-accessible	Application layer configuration per Port
ip2IfPortTable	1.3.6.1.4.1.164.3.1.6.7.9		not-accessible	Port Table.
ip2IfStatEntry	1.3.6.1.4.1.164.3.1.6.7.7.1		not-accessible	IP Statistics per bundle
ip2IfStatTable	1.3.6.1.4.1.164.3.1.6.7.7		not-accessible	Channels (Bundles) Statistics Table.
ip2IfTable	1.3.6.1.4.1.164.3.1.6.7.1		not-accessible	Channels Configuration Table.
lag	1.3.6.1.4.1.164.6.2.54
lagEntry	1.3.6.1.4.1.164.6.2.54.1.1		not-accessible	An entry in the LAG table.
lagStatEntry	1.3.6.1.4.1.164.6.2.54.2.1		not-accessible	An entry in the LAG Status table.
lagStatTable	1.3.6.1.4.1.164.6.2.54.2		not-accessible	A table defining Link Aggregation Groups Redundancy. This table is applicable only when lagDistributionMethod = oneToOne.
lagTable	1.3.6.1.4.1.164.6.2.54.1		not-accessible	A table defining Link Aggregation Groups port association, and other parameters.
NTF licenseUpdateTrap	1.3.6.1.4.1.164.6.1.0.27			This trap is sent whenever a license is successfully downloaded or whenever a license's demo duration is expired.
linkSelectorCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.17.2.1		not-accessible	An entry in table.
linkSelectorCnfgTable	1.3.6.1.4.1.164.3.2.3.2.17.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
linkSelectorPLinkEntry	1.3.6.1.4.1.164.3.2.3.2.17.3.1		not-accessible	An entry in table.
linkSelectorPLinkTable	1.3.6.1.4.1.164.3.2.3.2.17.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
NTF localConnStatusTrap	1.3.6.1.4.1.164.6.1.3.0.13			This trap is sent upon a change in Local connectivity of Bundle connection.
mapLinkEntry	1.3.6.1.4.1.164.3.3.4.2.1		not-accessible	An entry in table.
mapLinkTable	1.3.6.1.4.1.164.3.3.4.2		not-accessible	A table.
mappingProfileObjects	1.3.6.1.4.1.164.6.3.9
mapWanGen	1.3.6.1.4.1.164.3.1.5
markingProfileEntry	1.3.6.1.4.1.164.6.3.12.1		not-accessible	A conceptual row where each row contains one Marking attribute.
markingProfileTable	1.3.6.1.4.1.164.6.3.12		not-accessible	Marking profile table. Each profile holds a marking function which converts CoS values to Service Provider priority values.
maskingEntry	1.3.6.1.4.1.164.4.1.6.3.1		not-accessible	Defines the contents of each line in the mask table.
maskingTable	1.3.6.1.4.1.164.4.1.6.3		not-accessible	This is the new masking scheme. Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement and an action defined by maskingOperation.
mdlAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.3.3.2.1		not-accessible	An entry in table.
mdlAlarmsCmprTable	1.3.6.1.4.1.164.3.1.3.3.2		not-accessible	A table.
mdlAlr	1.3.6.1.4.1.164.3.3.2.1.3
mdlAlrEntry	1.3.6.1.4.1.164.3.3.2.1.3.1.1		not-accessible	An entry in table.
mdlAlrMaskEntry	1.3.6.1.4.1.164.3.3.2.1.3.2.1		not-accessible	An entry in table.
mdlAlrMaskTable	1.3.6.1.4.1.164.3.3.2.1.3.2		not-accessible	The list of card masked alarms.
mdlAlrTable	1.3.6.1.4.1.164.3.3.2.1.3.1		not-accessible	The list of card alarms.
mdlCEntry	1.3.6.1.4.1.164.3.3.2.1.2.1		not-accessible	An entry in table.
mdlCl	1.3.6.1.4.1.164.3.3.2.2
mdlClEntry	1.3.6.1.4.1.164.3.3.2.2.1.1		not-accessible	An entry in table.
mdlClTable	1.3.6.1.4.1.164.3.3.2.2.1		not-accessible	A table.
mdlCmprEntry	1.3.6.1.4.1.164.3.1.3.3.1.1		not-accessible	An entry in table.
mdlCmprTable	1.3.6.1.4.1.164.3.1.3.3.1		not-accessible	A table.
NTF mdlConnectTrap	1.3.6.1.4.1.164.3.3.0.3			This trap is sent when a card is removed.
mdlCPrgEntry	1.3.6.1.4.1.164.3.1.3.2.1.1		not-accessible	An entry in table.
mdlCPrgTable	1.3.6.1.4.1.164.3.1.3.2.1		not-accessible	A table.
mdlCTable	1.3.6.1.4.1.164.3.3.2.1.2		not-accessible	A table.
mdlDacsMux	1.3.6.1.4.1.164.3.3.2
mdlGen	1.3.6.1.4.1.164.3.3.2.1
mdlMux	1.3.6.1.4.1.164.3.2.2
mdlPbxFramerCnfg	1.3.6.1.4.1.164.3.2.2.1.1
mdlPbxFramerCnfgEntry	1.3.6.1.4.1.164.3.2.2.1.1.1.1		not-accessible	An entry in table.
mdlPbxFramerCnfgTable	1.3.6.1.4.1.164.3.2.2.1.1.1		not-accessible	This table contains parameters relevant to a module belonging to a digital voice system, except mdlPbxFraEnhEcho which is relevant also for analog cards.
mdlProtIpEntry	1.3.6.1.4.1.164.3.2.2.1.2.1		not-accessible	An entry in table.
mdlProtIpTable	1.3.6.1.4.1.164.3.2.2.1.2		not-accessible	This table contains Protected IP Addresses for ML-IP cards when working in IP Ring Mode.
mdlPs	1.3.6.1.4.1.164.3.3.2.3
mdlPsEntry	1.3.6.1.4.1.164.3.3.2.3.1.1		not-accessible	An entry in table.
mdlPsTable	1.3.6.1.4.1.164.3.3.2.3.1		not-accessible	A table.
mdlSAlrEntry	1.3.6.1.4.1.164.3.1.3.1.2.1		not-accessible	An entry in table.
mdlSAlrTable	1.3.6.1.4.1.164.3.1.3.1.2		not-accessible	The list of card agent alarms ; includes also an alarm indicating existence of alarms on its ports if there are any.
mdlSEntry	1.3.6.1.4.1.164.3.3.2.1.1.1		not-accessible	An entry in table.
mdlSInstEntry	1.3.6.1.4.1.164.3.1.3.1.1.1		not-accessible	An entry in table.
mdlSInstTable	1.3.6.1.4.1.164.3.1.3.1.1		not-accessible	A table.
mdlSTable	1.3.6.1.4.1.164.3.3.2.1.1		not-accessible	A table.
mdlStatEntry	1.3.6.1.4.1.164.3.2.2.2.1.1		not-accessible	An entry in table.
mdlStatTable	1.3.6.1.4.1.164.3.2.2.2.1		not-accessible	A table.
mdlWanGen	1.3.6.1.4.1.164.3.1.3
mngEntry	1.3.6.1.4.1.164.6.2.7.1		not-accessible	An entry in table.
mngTrapIpTable	1.3.6.1.4.1.164.6.2.7		not-accessible	This table indicates the destination address of the traps. Internally it will be limited to ten addresses.
NTF modlChangeTrap	1.3.6.1.4.1.164.6.1.0.26			This trap is sent whenever a module is inserted or removed. The trap should include the new module type (e.g. modlParamType).
modlParam	1.3.6.1.4.1.164.6.2.32.1
modlParamEntry	1.3.6.1.4.1.164.6.2.32.1.1.1		not-accessible	An entry in table.
modlParamTable	1.3.6.1.4.1.164.6.2.32.1.1		not-accessible	This table include parameters for system modules.
NTF moduleFailTrap	1.3.6.1.4.1.164.6.1.0.8			This trap is sent upon a module failure.
NTF moduleInitFailTrap	1.3.6.1.4.1.164.6.1.0.9			This trap is sent upon a module initialization failure.
muxHub	1.3.6.1.4.1.164.3.2
muxHubEvents	1.3.6.1.4.1.164.3.2.0			The events for .
newMasking	1.3.6.1.4.1.164.4.1.6
opticalPort	1.3.6.1.4.1.164.6.2.15.8
optPrtCnfgEntry	1.3.6.1.4.1.164.6.2.15.8.2.1		not-accessible	An entry in table.
optPrtCnfgTable	1.3.6.1.4.1.164.6.2.15.8.2		not-accessible	A table - optical port configuration
optPrtMonitorEntry	1.3.6.1.4.1.164.6.2.15.8.1.1		not-accessible	An entry in table.
optPrtMonitorTable	1.3.6.1.4.1.164.6.2.15.8.1		not-accessible	A table - optical port (e.g SFP) monitoring parameters, according to SFF-8472 Specification for Diagnostic Monitoring Interface for Optical Xcvrs. and ITU-T rec. G.958
physicalConnectorEntry	1.3.6.1.4.1.164.6.2.15.1.1		not-accessible	An entry in table.
physicalConnectorTable	1.3.6.1.4.1.164.6.2.15.1		not-accessible	This table includes the connector type of ports or interfaces.
portQos	1.3.6.1.4.1.164.6.3.4
portTrafficClassEntry	1.3.6.1.4.1.164.6.3.5.1.1		not-accessible	An entry in portTrafficClassTable.
portTrafficClassTable	1.3.6.1.4.1.164.6.3.5.1		not-accessible	Mapping of port to Traffic Class level.
prtAcmCnfg	1.3.6.1.4.1.164.3.2.3.2.20
prtAcmCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.20.1.1		not-accessible	An entry in table.
prtAcmCnfgTable	1.3.6.1.4.1.164.3.2.3.2.20.1		not-accessible	This is a table for ACM port parameters.
prtAgendaBehaviourEntry	1.3.6.1.4.1.164.3.1.4.2.2.1.1		not-accessible	An entry in table.
prtAgendaBehaviourTable	1.3.6.1.4.1.164.3.1.4.2.2.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtAlarmsCmprEntry	1.3.6.1.4.1.164.3.1.4.3.3.1		not-accessible	An entry in table.
prtAlarmsCmprTable	1.3.6.1.4.1.164.3.1.4.3.3		not-accessible	A table.
prtAlr	1.3.6.1.4.1.164.3.3.3.1.4
prtAlrMaskEntry	1.3.6.1.4.1.164.3.3.3.1.4.2.1		not-accessible	An entry in table.
prtAlrMaskTable	1.3.6.1.4.1.164.3.3.3.1.4.2		not-accessible	A table.
prtBdbandIndEntry	1.3.6.1.4.1.164.3.1.6.8.1.1.1		not-accessible	An entry in the Indication Signal table.
prtBdbandIndTable	1.3.6.1.4.1.164.3.1.6.8.1.1		not-accessible	The Indication Signal table.
prtBertEntry	1.3.6.1.4.1.164.3.3.3.1.5.1		not-accessible	An entry in table.
prtBertTable	1.3.6.1.4.1.164.3.3.3.1.5		not-accessible	This table includes the BERT parameters, counters and commands. The configurable parameters: - prtBertPattern - prtBertInjectRate - prtBertTs are not Set per configuration (same for all Configurations) but start being applied by the Agent only upon successful Update/Download operation. Therefore, Set will enter the values to the Temporary Configuration of the agent, while Get will get the values of the Active Configuration.
prtCfgParam	1.3.6.1.4.1.164.3.3.3.1.7
prtCfgParamEntry	1.3.6.1.4.1.164.3.3.3.1.7.1.1		not-accessible	An entry in table.
prtCfgParamTable	1.3.6.1.4.1.164.3.3.3.1.7.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. KMUX parameters are for the cards: KMBE/New, KVF.6 family.
prtClCnfg	1.3.6.1.4.1.164.3.2.3.2.1
prtClkSrc	1.3.6.1.4.1.164.6.2.15.7
NTF prtClkSrcChangeTrap	1.3.6.1.4.1.164.6.1.0.7			This trap is sent upon any port clock change.
prtClkSrcEntry	1.3.6.1.4.1.164.6.2.15.7.1.1		not-accessible	An entry in table.
prtClkSrcTable	1.3.6.1.4.1.164.6.2.15.7.1		not-accessible	A table - Parameters for master and fallback clock source of ports .
prtCmprEntry	1.3.6.1.4.1.164.3.1.4.3.1.1		not-accessible	An entry in table.
prtCmprTable	1.3.6.1.4.1.164.3.1.4.3.1		not-accessible	A table.
prtCnfgAgenda	1.3.6.1.4.1.164.3.1.4.2.2
prtCnfgAgendaEntry	1.3.6.1.4.1.164.3.1.4.2.2.2.1		not-accessible	An entry in table.
prtCnfgAgendaTable	1.3.6.1.4.1.164.3.1.4.2.2.2		not-accessible	This table allows the user to schedule the time a session is active per week basis.
prtCrStatis	1.3.6.1.4.1.164.3.1.4.1.3.2
prtCrStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.2.1.1		not-accessible	An entry in table.
prtCrStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.2.1		not-accessible	This table is applicable only for an active port running a CR protocol .
prtDacsMux	1.3.6.1.4.1.164.3.3.3
prtDim	1.3.6.1.4.1.164.3.3.3.5
prtDimCnfgEntry	1.3.6.1.4.1.164.3.3.3.5.1.1		not-accessible	The write operation into the Table Objects is valid only for the TmpCnfg entry (prtDimCnfgIdx=255).
prtDimCnfgTable	1.3.6.1.4.1.164.3.3.3.5.1		not-accessible	A table.
prtDimDestEntry	1.3.6.1.4.1.164.3.3.3.5.2.1		not-accessible	The write operation is valid only for the TmpCnfg entry (prtDimDestCnfgIdx=255).
prtDimDestTable	1.3.6.1.4.1.164.3.3.3.5.2		not-accessible	A table.
prtDlciCmprEntry	1.3.6.1.4.1.164.3.1.4.3.2.1		not-accessible	An entry in table.
prtDlciCmprTable	1.3.6.1.4.1.164.3.1.4.3.2		not-accessible	A table.
prtDlciStatis	1.3.6.1.4.1.164.3.1.4.1.3.3
prtDlciStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.3.1.1		not-accessible	An entry in table.
prtDlciStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.3.1		not-accessible	This table is applicable only for an active port running an FR, FR+ or CR protocol, with valid DLCIs .
prtDS1Events	1.3.6.1.4.1.164.3.1.6.4.0
prtDs1PerfHistory	1.3.6.1.4.1.164.3.1.6.4.1
prtDs3CurrentEntry	1.3.6.1.4.1.164.3.1.6.3.1.2.1		not-accessible	An entry in the DS3 Current table.
prtDs3CurrentTable	1.3.6.1.4.1.164.3.1.6.3.1.2		not-accessible	The DS3 Current table.
prtDs3IfEntry	1.3.6.1.4.1.164.3.1.6.3.1.1.1		not-accessible	An entry in the DS3 interface table.
prtDs3IntervalEntry	1.3.6.1.4.1.164.3.1.6.3.1.3.1		not-accessible	An entry in the DS3 Interval table.
prtDs3IntervalTable	1.3.6.1.4.1.164.3.1.6.3.1.3		not-accessible	The DS3 Interval table.
prtDs3PerfHistory	1.3.6.1.4.1.164.3.1.6.3.1
prtDs3TotalEntry	1.3.6.1.4.1.164.3.1.6.3.1.4.1		not-accessible	An entry of Total table.
prtDs3TotalTable	1.3.6.1.4.1.164.3.1.6.3.1.4		not-accessible	A list of Total entries.
prtE2Cnfg	1.3.6.1.4.1.164.3.2.3.2.21
prtE2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.21.1.1		not-accessible	An entry in table.
prtE2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.21.1		not-accessible	This is a table for E2 port parameters.
prtExClCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.1.1.1		not-accessible	All the entries at this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExClCnfgTable	1.3.6.1.4.1.164.3.2.3.2.1.1		not-accessible	A table.
prtExHs4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.7.1.1		not-accessible	An entry in table.
prtExHs4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.7.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExHs4TsCnfgTable	1.3.6.1.4.1.164.3.2.3.2.7.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExHs4TsEntry	1.3.6.1.4.1.164.3.2.3.2.7.2.1		not-accessible	An entry in table.
prtExHsiCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.8.1.1		not-accessible	An entry in table.
prtExHsiCnfgTable	1.3.6.1.4.1.164.3.2.3.2.8.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExHsrCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.10.1.1		not-accessible	An entry in table.
prtExHsrCnfgTable	1.3.6.1.4.1.164.3.2.3.2.10.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExLs2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.4.1.1		not-accessible	An entry in table.
prtExLs2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.4.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExLs6CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.1.1		not-accessible	An entry in table.
prtExLs6CnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExLs6VCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.2.1		not-accessible	An entry in table.
prtExLs6VCnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExMbeCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.11.1.1		not-accessible	An entry in table.
prtExMbeCnfgTable	1.3.6.1.4.1.164.3.2.3.2.11.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExPh1MlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.1.1		not-accessible	An entry in table.
prtExPh1MlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.1		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to prtExPh1MlCnfgIdx=1.
prtExPh1MlTsEntry	1.3.6.1.4.1.164.3.2.3.2.2.2.1		not-accessible	An entry in table.
prtExPh1MlTsTable	1.3.6.1.4.1.164.3.2.3.2.2.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExPh1MlTsTest that will be written directly to the Active Configuration.
prtExPhPlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.3.1.1		not-accessible	An entry in table.
prtExPhPlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.3.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExPhPlDlciEntry	1.3.6.1.4.1.164.3.2.3.2.3.2.1		not-accessible	An entry in table.
prtExPhPlDlciTable	1.3.6.1.4.1.164.3.2.3.2.3.2		not-accessible	The write operation into the Table Objects is valid only at the TmpCnfg entry.
prtExPhPlModemEntry	1.3.6.1.4.1.164.3.2.3.2.3.3.1		not-accessible	An entry in table.
prtExPhPlModemTable	1.3.6.1.4.1.164.3.2.3.2.3.3		not-accessible	External Modem Parameters. The write operation into the Table Objects is valid only for the TmpCnfg entry.
prtExPVc4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.9.1.1		not-accessible	An entry in table.
prtExPVc4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.9.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExPVc4DlciEntry	1.3.6.1.4.1.164.3.2.3.2.9.2.1		not-accessible	An entry in table.
prtExPVc4DlciTable	1.3.6.1.4.1.164.3.2.3.2.9.2		not-accessible	The write operation into the Table Objects is valid only at the TmpCnfg entry.
prtExTreCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.12.1.1		not-accessible	An entry in table.
prtExTreCnfgTable	1.3.6.1.4.1.164.3.2.3.2.12.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExTsSplitEntry	1.3.6.1.4.1.164.3.1.4.2.1.1		not-accessible	An entry in table.
prtExTsSplitTable	1.3.6.1.4.1.164.3.1.4.2.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExTsBitTest that will be written directly to the Active Configuration.
prtExVc3CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.14.1.1		not-accessible	An entry in table.
prtExVc3CnfgTable	1.3.6.1.4.1.164.3.2.3.2.14.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExVcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.1.1		not-accessible	An entry in table.
prtExVcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtExVcPbxTsEntry	1.3.6.1.4.1.164.3.2.3.2.15.4.1		not-accessible	An entry in table.
prtExVcPbxTsTable	1.3.6.1.4.1.164.3.2.3.2.15.4		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtFrPlusCnfg	1.3.6.1.4.1.164.3.2.3.2.18
prtFrPlusCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.18.1.1		not-accessible	An entry in table.
prtFrPlusCnfgTable	1.3.6.1.4.1.164.3.2.3.2.18.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtFrStatis	1.3.6.1.4.1.164.3.1.4.1.3.1
prtFrStatisEntry	1.3.6.1.4.1.164.3.1.4.1.3.1.1.1		not-accessible	An entry in table.
prtFrStatisTable	1.3.6.1.4.1.164.3.1.4.1.3.1.1		not-accessible	This table is applicable only for an active port running an FR protocol .
prtGen	1.3.6.1.4.1.164.3.3.3.1
prtGenCnfgEntry	1.3.6.1.4.1.164.3.1.4.2.3.1		not-accessible	An entry in table.
prtGenCnfgTable	1.3.6.1.4.1.164.3.1.4.2.3		not-accessible	This table allows the user to configure general port parameters.
prtGenEntry	1.3.6.1.4.1.164.3.3.3.1.1.1		not-accessible	An entry in table.
prtGenParamTable	1.3.6.1.4.1.164.3.3.3.1.1		not-accessible	A table.
prtGenTestDurationEntry	1.3.6.1.4.1.164.3.3.3.1.2.1		not-accessible	An entry in table.
prtGenTestDurationTable	1.3.6.1.4.1.164.3.3.3.1.2		not-accessible	A table.
prtGenTsEntry	1.3.6.1.4.1.164.3.3.3.1.3.1		not-accessible	An entry in table.
prtGenTsTable	1.3.6.1.4.1.164.3.3.3.1.3		not-accessible	The write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch),exept some products which enable direct writing to the ActiveCnfg. This is written in the respective product's spec.
prtHdsl	1.3.6.1.4.1.164.3.3.3.7
prtHdslEntry	1.3.6.1.4.1.164.3.3.3.7.1.1		not-accessible	An entry in table.
prtHdslTable	1.3.6.1.4.1.164.3.3.3.7.1		not-accessible	HDSL port table.
prtHS	1.3.6.1.4.1.164.3.3.3.3
prtHs4Cnfg	1.3.6.1.4.1.164.3.2.3.2.7
prtHSBertEntry	1.3.6.1.4.1.164.3.3.3.3.2.1		not-accessible	An entry in table.
prtHSBertTable	1.3.6.1.4.1.164.3.3.3.3.2		not-accessible	A table.
prtHsfCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.6.1		not-accessible	An entry in table.
prtHsfCnfgTable	1.3.6.1.4.1.164.3.2.3.2.6		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtHsiCnfg	1.3.6.1.4.1.164.3.2.3.2.8
prtHSParamEntry	1.3.6.1.4.1.164.3.3.3.3.1.1		not-accessible	An entry in table.
prtHSParamTable	1.3.6.1.4.1.164.3.3.3.3.1		not-accessible	A table.
prtHsrCnfg	1.3.6.1.4.1.164.3.2.3.2.10
prtI	1.3.6.1.4.1.164.3.3.3.6
prtICnfgEntry	1.3.6.1.4.1.164.3.3.3.6.1.1		not-accessible	An entry in table.
prtICnfgTable	1.3.6.1.4.1.164.3.3.3.6.1		not-accessible	A table.
prtIn1p6VcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.2.1		not-accessible	An entry in table.
prtIn1p6VcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtIn7p8VcPbxCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.15.3.1		not-accessible	An entry in table.
prtIn7p8VcPbxCnfgTable	1.3.6.1.4.1.164.3.2.3.2.15.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInHsiCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.8.2.1		not-accessible	An entry in table.
prtInHsiCnfgTable	1.3.6.1.4.1.164.3.2.3.2.8.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry. This table is not applicable for MP-2100 HS-U card type.
prtInLs2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.4.2.1		not-accessible	An entry in table.
prtInLs2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.4.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInLs6CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.13.3.1		not-accessible	An entry in table.
prtInLs6CnfgTable	1.3.6.1.4.1.164.3.2.3.2.13.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInMbeCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.11.2.1		not-accessible	An entry in table.
prtInMbeCnfgTable	1.3.6.1.4.1.164.3.2.3.2.11.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInPh1MlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.3.1		not-accessible	An entry in table.
prtInPh1MlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.3		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInPh1MlDlciEntry	1.3.6.1.4.1.164.3.2.3.2.2.4.1		not-accessible	An entry in table.
prtInPh1MlDlciTable	1.3.6.1.4.1.164.3.2.3.2.2.4		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInTreCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.12.2.1		not-accessible	An entry in table.
prtInTreCnfgTable	1.3.6.1.4.1.164.3.2.3.2.12.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtInVc3CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.14.2.1		not-accessible	An entry in table.
prtInVc3CnfgTable	1.3.6.1.4.1.164.3.2.3.2.14.2		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtIP	1.3.6.1.4.1.164.6.2.15.6
prtIpParamEntry	1.3.6.1.4.1.164.6.2.15.6.1.1		not-accessible	An entry in table.
prtIpParamTable	1.3.6.1.4.1.164.6.2.15.6.1		not-accessible	A table - Parameters for IP Ports.
prtIsdnCnfg	1.3.6.1.4.1.164.3.2.3.2.16
prtIsdnCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.16.1.1		not-accessible	An entry in table.
prtIsdnCnfgTable	1.3.6.1.4.1.164.3.2.3.2.16.1		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtIsdnDirectoryEntry	1.3.6.1.4.1.164.3.2.3.2.16.3.1		not-accessible	An entry in table.
prtIsdnDirectoryTable	1.3.6.1.4.1.164.3.2.3.2.16.3		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtIsdnEndpointEntry	1.3.6.1.4.1.164.3.2.3.2.16.2.1		not-accessible	An entry in table.
prtIsdnEndpointTable	1.3.6.1.4.1.164.3.2.3.2.16.2		not-accessible	The write operation into the table objects is valid only to the TmpCnfg entry.
prtIsdnStatusEntry	1.3.6.1.4.1.164.3.2.3.1.16.1		not-accessible	Entries for ISDN Statistics parameters that do not appear in the standard MIBs or for agents that don't support the standard Index of Call Set Up Time.
prtIsdnStatusTable	1.3.6.1.4.1.164.3.2.3.1.16		not-accessible	This table contains ISDN Statistics parameters that do not appear in the standard MIBs or for agents that don't support the standard Index of Call Set Up Time.
prtLanWanCnfg	1.3.6.1.4.1.164.3.2.3.2.22
prtLanWanCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.22.1.1		not-accessible	An entry in table.
prtLanWanCnfgTable	1.3.6.1.4.1.164.3.2.3.2.22.1		not-accessible	This is a table for Lan-Wan port parameters.
prtLogicalCnfg	1.3.6.1.4.1.164.3.2.3.2.17
prtLogicalCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.17.1.1		not-accessible	An entry in table.
prtLogicalCnfgTable	1.3.6.1.4.1.164.3.2.3.2.17.1		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtLs2Cnfg	1.3.6.1.4.1.164.3.2.3.2.4
prtLs6Cnfg	1.3.6.1.4.1.164.3.2.3.2.13
prtMbeCnfg	1.3.6.1.4.1.164.3.2.3.2.11
prtMl4Cnfg	1.3.6.1.4.1.164.3.2.3.2.19
prtMl4CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.19.1.1		not-accessible	An entry in table.
prtMl4CnfgTable	1.3.6.1.4.1.164.3.2.3.2.19.1		not-accessible	This is an extension table for MTML-4 card parameters.
prtMonEntry	1.3.6.1.4.1.164.3.3.3.1.6.1		not-accessible	An entry in table.
prtMonTable	1.3.6.1.4.1.164.3.3.3.1.6		not-accessible	For DXC, the write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch).
prtMux	1.3.6.1.4.1.164.3.2.3
prtParam	1.3.6.1.4.1.164.6.2.15.5
prtParamEntry	1.3.6.1.4.1.164.6.2.15.5.1.1		not-accessible	An entry in table.
prtParamTable	1.3.6.1.4.1.164.6.2.15.5.1		not-accessible	This table includes general port parameters. The meaning is different for every product that supports it due to a general parameter - prtControlCnfg. For ACE2002: -This table is used as a mechanism to create the next interface index. The algorithm description: The NMS will send the agent the following get command: get(nextIfIndex.index), where index=interface on which the new index is dependent on. Upon this command the agent will generate and return the new index to the NMS. - This table is partially supported according to the interface type. Upon getNext function the irrelevant parameters will be skipped.
prtPerfEntry	1.3.6.1.4.1.164.6.2.15.3.1.1		not-accessible	An entry in table.
prtPerformance	1.3.6.1.4.1.164.6.2.15.3
prtPerfTable	1.3.6.1.4.1.164.6.2.15.3.1		not-accessible	This table includes G.826 ports or interfaces.
prtPh1MlCnfg	1.3.6.1.4.1.164.3.2.3.2.2
prtPhMlCnfgEntry	1.3.6.1.4.1.164.3.2.3.2.2.5.1		not-accessible	An entry in table.
prtPhMlCnfgTable	1.3.6.1.4.1.164.3.2.3.2.2.5		not-accessible	The write operation into the Table Objects is valid only to the TmpCnfg entry.
prtPhPlCnfg	1.3.6.1.4.1.164.3.2.3.2.3
prtPhyConfigEntry	1.3.6.1.4.1.164.3.1.6.8.1.2.1		not-accessible	An entry in the Phy Config table.
prtPhyConfigTable	1.3.6.1.4.1.164.3.1.6.8.1.2		not-accessible	The Phy Config table. Used now for Phy25.6 Mbps.
prtPhyCurrentEntry	1.3.6.1.4.1.164.3.1.6.8.2.1.1		not-accessible	An entry in the 25.6 Mbps Line Current table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.
prtPhyCurrentTable	1.3.6.1.4.1.164.3.1.6.8.2.1		not-accessible	The 25.6 Mbps Section/Line Current table.
prtPhyIntervalEntry	1.3.6.1.4.1.164.3.1.6.8.2.2.1		not-accessible	An entry in the 25.6 Mbps Line Interval table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.
prtPhyIntervalTable	1.3.6.1.4.1.164.3.1.6.8.2.2		not-accessible	The Line Interval table.
prtPhyPerfHistory	1.3.6.1.4.1.164.3.1.6.8.2
prtPriorityEntry	1.3.6.1.4.1.164.6.3.4.1.1		not-accessible	An entry in table.
prtPriorityTable	1.3.6.1.4.1.164.6.3.4.1		not-accessible	A table - Parameters per port per Priority .
prtPVc4Cnfg	1.3.6.1.4.1.164.3.2.3.2.9
prtQosEntry	1.3.6.1.4.1.164.6.3.4.2.1		not-accessible	An entry in table.
prtQosTable	1.3.6.1.4.1.164.6.3.4.2		not-accessible	Port QoS (Quality of Service) table.
prtSAlarmEntry	1.3.6.1.4.1.164.3.3.3.1.4.1.1		not-accessible	An entry in table.
prtSAlarmTable	1.3.6.1.4.1.164.3.3.3.1.4.1		not-accessible	A table.
prtSAlrEntry	1.3.6.1.4.1.164.3.1.4.1.2.1		not-accessible	An entry in table.
prtSAlrTable	1.3.6.1.4.1.164.3.1.4.1.2		not-accessible	The list of port agent alarms.
prtSDs3IfTable	1.3.6.1.4.1.164.3.1.6.3.1.1		not-accessible	The DS3 interface table.
prtSExHsfStatEntry	1.3.6.1.4.1.164.3.2.3.1.6.1		not-accessible	An entry in table.
prtSExHsfStatTable	1.3.6.1.4.1.164.3.2.3.1.6		not-accessible	A table.
prtSInstEntry	1.3.6.1.4.1.164.3.1.4.1.1.1		not-accessible	An entry in table.
prtSInstTable	1.3.6.1.4.1.164.3.1.4.1.1		not-accessible	A table.
prtSP	1.3.6.1.4.1.164.3.3.3.4
prtSpCnfgEntry	1.3.6.1.4.1.164.3.3.3.4.1.1		not-accessible	All the entries at this table are identical(have the same value) at all the configurations(1..255) except at the TmpCnfg. - For products supporting more than one configuration, the write operation into the Table Objects is valid only at the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table Objects will be to prtSpCnfgIdx=1.
prtSpCnfgTable	1.3.6.1.4.1.164.3.3.3.4.1		not-accessible	A table.
prtSpEntry	1.3.6.1.4.1.164.6.2.15.2.1.1		not-accessible	Supervisory port parameter table.
prtSpTable	1.3.6.1.4.1.164.6.2.15.2.1		not-accessible	A table.
NTF prtStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.3			This trap is sent whenever the state of a port changed. Attached, will be parameter/s that indicate the new port status. The attached variables will be specified in the specifications of the products supporting this trap.
prtSupervisory	1.3.6.1.4.1.164.6.2.15.2
prtT1E1	1.3.6.1.4.1.164.3.3.3.2
prtT1E1CnfgEntry	1.3.6.1.4.1.164.3.3.3.2.2.1		not-accessible	An entry in the T1/E1 port configuration table.
prtT1E1CnfgTable	1.3.6.1.4.1.164.3.3.3.2.2		not-accessible	T1/E1 port configuration table.
prtT1E1FdlMsgEntry	1.3.6.1.4.1.164.3.3.3.2.3.1		not-accessible	An entry in table.
prtT1E1FdlMsgTable	1.3.6.1.4.1.164.3.3.3.2.3		not-accessible	This table is applicable for a T1 interface with 'esf' LineType or E1 interface, when CRC is enabled (LineType).
prtT1E1StatEntry	1.3.6.1.4.1.164.3.3.3.2.1.1		not-accessible	An entry in the T1/E1 port statistics table.
prtT1E1StatTable	1.3.6.1.4.1.164.3.3.3.2.1		not-accessible	T1/E1 port statistics table.
prtT1FdlMsgEntry	1.3.6.1.4.1.164.3.1.4.1.3.4.1.1		not-accessible	An entry in table.
prtT1FdlMsgTable	1.3.6.1.4.1.164.3.1.4.1.3.4.1		not-accessible	This table is applicable for a T1 interface with 'esf' LineType .
prtT1Statis	1.3.6.1.4.1.164.3.1.4.1.3.4
prtT3E3	1.3.6.1.4.1.164.3.3.3.8
prtT3E3CnfgEntry	1.3.6.1.4.1.164.3.3.3.8.1.1		not-accessible	An entry in the T3/E3 port configuration table.
prtT3E3CnfgTable	1.3.6.1.4.1.164.3.3.3.8.1		not-accessible	T3/E3 port configuration table.
prtTest	1.3.6.1.4.1.164.6.2.15.4
prtTestEntry	1.3.6.1.4.1.164.6.2.15.4.1.1		not-accessible	An entry in table.
prtTestTable	1.3.6.1.4.1.164.6.2.15.4.1		not-accessible	This table includes test data for ports or interfaces.
prtTrafficClass	1.3.6.1.4.1.164.6.3.5
prtTreCnfg	1.3.6.1.4.1.164.3.2.3.2.12
prtVc2CnfgEntry	1.3.6.1.4.1.164.3.2.3.2.5.1		not-accessible	An entry in table.
prtVc2CnfgTable	1.3.6.1.4.1.164.3.2.3.2.5		not-accessible	- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to prtVc2CnfgIdx=1.
prtVc3Cnfg	1.3.6.1.4.1.164.3.2.3.2.14
prtVcPbxCnfg	1.3.6.1.4.1.164.3.2.3.2.15
prtWanGen	1.3.6.1.4.1.164.3.1.4
qInternalProfileEntry	1.3.6.1.4.1.164.6.3.11.2.1		not-accessible	A conceptual row where each row contains one Queue attribute.
qInternalProfileTable	1.3.6.1.4.1.164.6.3.11.2		not-accessible	This table holds queue profiles.
qosFlowMappingEntry	1.3.6.1.4.1.164.6.3.9.2.1		not-accessible	Each entry in this table describes one Flow Mapping. The information includes combination (AND function) of all the classifications, as defined in the qosFlowMappingCriteria field. Classifiers are: TOS, DSCP, VLAN ID, MAC and IP source and destination addresses, IP protocol, IP Precedence, TCP and UDP source and destination ports.
qosFlowMappingTable	1.3.6.1.4.1.164.6.3.9.2		not-accessible	A table of Flow Mapping.
qProfileEntry	1.3.6.1.4.1.164.6.3.11.1.1		not-accessible	A conceptual row where each row contains one Queue Cluster attribute.
qProfileTable	1.3.6.1.4.1.164.6.3.11.1		not-accessible	This table defines the profiles for a cluster of queues.
queueGroupEntry	1.3.6.1.4.1.164.6.3.11.3.1		not-accessible	A conceptual row where each row contains one Queue group.
queueGroupTable	1.3.6.1.4.1.164.6.3.11.3		not-accessible	This table defines the queue groups/blocks,their level and connections between them.
queueProfileObjects	1.3.6.1.4.1.164.6.3.11
rad	1.3.6.1.4.1.164
radAce	1.3.6.1.4.1.164.6.1.12.3
radAce101	1.3.6.1.4.1.164.6.1.12.3.1
radAce102	1.3.6.1.4.1.164.6.1.12.3.2
radAce2002	1.3.6.1.4.1.164.6.1.12.2.6
radAce2002E	1.3.6.1.4.1.164.6.1.12.2.7
radAce2005	1.3.6.1.4.1.164.6.1.12.2.5
radAce201	1.3.6.1.4.1.164.6.1.12.3.7
radAce202	1.3.6.1.4.1.164.6.1.12.2.14
radAce20E	1.3.6.1.4.1.164.6.1.12.2.3
radAce20T	1.3.6.1.4.1.164.6.1.12.2.4
radAce2E	1.3.6.1.4.1.164.6.1.12.2.8
radAce2T	1.3.6.1.4.1.164.6.1.12.2.9
radAce3100	1.3.6.1.4.1.164.6.1.12.3.9
radAce3100PSN	1.3.6.1.4.1.164.6.1.12.3.12
radAce3105	1.3.6.1.4.1.164.6.1.12.3.18
radAce3200	1.3.6.1.4.1.164.6.1.12.3.8
radAce3200PSN	1.3.6.1.4.1.164.6.1.12.3.13
radAce3205	1.3.6.1.4.1.164.6.1.12.3.17
radAce3400	1.3.6.1.4.1.164.6.1.12.3.10
radAce3400PSN	1.3.6.1.4.1.164.6.1.12.3.14
radAce3402	1.3.6.1.4.1.164.6.1.12.3.11
radAce3402PSN	1.3.6.1.4.1.164.6.1.12.3.15
radAce3600	1.3.6.1.4.1.164.6.1.12.3.16
radAce50	1.3.6.1.4.1.164.6.1.12.3.3
radAce52	1.3.6.1.4.1.164.6.1.12.3.4
radAce52L	1.3.6.1.4.1.164.6.1.12.3.5
radAmc102	1.3.6.1.4.1.164.6.1.12.2.12
radAmc102c	1.3.6.1.4.1.164.6.1.12.2.13
radAmcdE1	1.3.6.1.4.1.164.6.1.12.2.1
radAmcdT1	1.3.6.1.4.1.164.6.1.12.2.2
radAPD2	1.3.6.1.4.1.164.6.1.8.6
radAPD8	1.3.6.1.4.1.164.6.1.8.7
radAPS16	1.3.6.1.4.1.164.6.1.8.9
radAPS24	1.3.6.1.4.1.164.6.1.8.10
radAPS8	1.3.6.1.4.1.164.6.1.8.8
radAsmi450R1152	1.3.6.1.4.1.164.6.1.3.47
radAsmi450R1152Sa	1.3.6.1.4.1.164.6.1.3.46
radAsmi450R768	1.3.6.1.4.1.164.6.1.3.45
radAsmi450R768Sa	1.3.6.1.4.1.164.6.1.3.44
radAsmi52A	1.3.6.1.4.1.164.6.1.3.99
radAsmi52L	1.3.6.1.4.1.164.6.1.3.121
radAsmi54	1.3.6.1.4.1.164.6.1.3.140
radAtm	1.3.6.1.4.1.164.12
radAtmCsuDsu	1.3.6.1.4.1.164.6.1.12.2
radBridgeCOD	1.3.6.1.4.1.164.4.1.4
radBridgeCODCondEntry	1.3.6.1.4.1.164.4.1.4.4.1		not-accessible	Each radBridgeCODCondEntry consists of the following parameters
radBridgeCODCondTable	1.3.6.1.4.1.164.4.1.4.4		not-accessible	The table of COD Condition parameters
radBridgeCODEntry	1.3.6.1.4.1.164.4.1.4.1.1		not-accessible	Each radBridgeCODEntry consists of the following parameters
radBridgeCODParamTable	1.3.6.1.4.1.164.4.1.4.1		not-accessible	The table of COD parameters
radBridgeCODTimeTriggerEntry	1.3.6.1.4.1.164.4.1.4.2.1		not-accessible	Each radBridgeCODTimeTriggerEntry consists of the following parameters
radBridgeCODTimeTriggerTable	1.3.6.1.4.1.164.4.1.4.2		not-accessible	The table of COD parameters
radBridgeCODTraffic	1.3.6.1.4.1.164.4.1.4.3
radBridgeCODTrafficEntry	1.3.6.1.4.1.164.4.1.4.3.1.1		not-accessible	Each radBridgeCODTrafficEntry consists of the following parameters.
radBridgeCODTrafficTable	1.3.6.1.4.1.164.4.1.4.3.1		not-accessible	The table of COD Traffic trigger
radBridgeCurrentEntry	1.3.6.1.4.1.164.4.1.7.1.1		not-accessible	An entry in the RAD Bridge Current table.
radBridgeCurrentTable	1.3.6.1.4.1.164.4.1.7.1		not-accessible	The RAD Bridge Current table.
radBridgeDot1qVlanStaticEntry	1.3.6.1.4.1.164.4.1.9.2.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
radBridgeDot1qVlanStaticTable	1.3.6.1.4.1.164.4.1.9.2		not-accessible	A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
radBridgeGenCfgEntry	1.3.6.1.4.1.164.4.1.9.4.1		not-accessible	Describes an entry in the radBridgeGenCfgTable.
radBridgeGenCfgTable	1.3.6.1.4.1.164.4.1.9.4		not-accessible	A table containing Bridge configuration parameters.
radBridgeGenCnfg	1.3.6.1.4.1.164.4.1.9
radBridgeGenFlowEntry	1.3.6.1.4.1.164.4.1.9.1.1		not-accessible	Static information for a Bridge configured into the device by management.
radBridgeGenFlowTable	1.3.6.1.4.1.164.4.1.9.1		not-accessible	A table containing static configuration information for Bridge configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
radBridgeIntervalEntry	1.3.6.1.4.1.164.4.1.7.2.1		not-accessible	An entry in the RAD Bridge Interval table.
radBridgeIntervalTable	1.3.6.1.4.1.164.4.1.7.2		not-accessible	The RAD Bridge Interval table.
radBridgeInvBasePortEntry	1.3.6.1.4.1.164.4.1.10.1.1		not-accessible	The bridge port number for each bridge port interface index.
radBridgeInvBasePortTable	1.3.6.1.4.1.164.4.1.10.1		not-accessible	An inversed table to dot1dBasePortTable from RFC1493 with reduced information. This table index is known to the NMS and this way the needed information can be received by just one Get command, instead of searching the entire dot1dBasePortTable (where it is an attribute).
radBridgeIPX	1.3.6.1.4.1.164.4.1.5
radBridgeIPXdriver	1.3.6.1.4.1.164.4.1.5.1
radBridgeIPXRip	1.3.6.1.4.1.164.4.1.5.2
radBridgeIPXRipInfEntry	1.3.6.1.4.1.164.4.1.5.2.7.1		not-accessible	Each entry corresponds to one ifindex.
radBridgeIPXRipInfTable	1.3.6.1.4.1.164.4.1.5.2.7		not-accessible	The RIP interface table.
radBridgeIPXRipTable	1.3.6.1.4.1.164.4.1.5.2.6		not-accessible	The routing table used by RIP to calculate routes to remote desination networks.
radBridgeIPXRipTableEntry	1.3.6.1.4.1.164.4.1.5.2.6.1		not-accessible	The routing information for one of this entity's destination networks.
radBridgeIPXSap	1.3.6.1.4.1.164.4.1.5.3
radBridgeIPXSapInfEntry	1.3.6.1.4.1.164.4.1.5.3.7.1		not-accessible	Each entry corresponds to one ifindex.
radBridgeIPXSapInfTable	1.3.6.1.4.1.164.4.1.5.3.7		not-accessible	The Sap interface table.
radBridgeIPXSapTable	1.3.6.1.4.1.164.4.1.5.3.6		not-accessible	The Server Information table is used by SAP to store information of services which are available on the internetwork.
radBridgeIPXSapTableEntry	1.3.6.1.4.1.164.4.1.5.3.6.1		not-accessible	The server information for one of this entity's server entries.
radBridgeMaskEntry	1.3.6.1.4.1.164.4.1.3.1		not-accessible	An entry in table radBridgeMaskTable.
radBridgeMaskTable	1.3.6.1.4.1.164.4.1.3		not-accessible	Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement consisting of up to three mask definitions and an action defined by radBridgeMaskOper. Different types of mask entries are supported, as defined by radBridgeMaskType.
radBridgePerformance	1.3.6.1.4.1.164.4.1.7
radBridgePort	1.3.6.1.4.1.164.4.1.13
radBridgePortBaseVlan	1.3.6.1.4.1.164.4.1.8
radBridgePortBaseVlanEntry	1.3.6.1.4.1.164.4.1.8.1.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
radBridgePortBaseVlanTable	1.3.6.1.4.1.164.4.1.8.1		not-accessible	A table containing static configuration information for each VLAN configured into the device by management. All entries are permanent and will be restored after the device is reset.
radBridgePortCnfgEntry	1.3.6.1.4.1.164.4.1.13.1.1		not-accessible	An entry in the table.
radBridgePortCnfgTable	1.3.6.1.4.1.164.4.1.13.1		not-accessible	The Bridge Port Configuration Table.
radBridgePortVlanMemberEntry	1.3.6.1.4.1.164.4.1.8.2.1		not-accessible	An entry in the Bridge Ports-VLANs Memebership table.
radBridgePortVlanMemberTable	1.3.6.1.4.1.164.4.1.8.2		not-accessible	The Bridge Ports-VLAN Membership table. This table enables the user to assign: - Several VLANs to a Port. - Several Ports to a VLAN.
radBridges	1.3.6.1.4.1.164.4
radBridgeStatus	1.3.6.1.4.1.164.4.1.10
radBridgeStp	1.3.6.1.4.1.164.4.1.11
radBridgeStpCnfgEntry	1.3.6.1.4.1.164.4.1.11.1.1		not-accessible	An entry in the radBridgeStpCnfgTable.
radBridgeStpCnfgTable	1.3.6.1.4.1.164.4.1.11.1		not-accessible	STP Configuration table. STP=Spanning Tree Protocol. It includes STP configurable parameters that in BRIDGE-MIB are scalars, while we need them per card/bridge/interface and per different configurations.
radBridgeStpStatEntry	1.3.6.1.4.1.164.4.1.11.2.1		not-accessible	An entry in the radBridgeStpStatTable.
radBridgeStpStatTable	1.3.6.1.4.1.164.4.1.11.2		not-accessible	STP Status table. STP=Spanning Tree Protocol. It includes STP status parameters that in BRIDGE-MIB are scalars, while we need them per card/bridge/interface. For devices that have several configurations, this table is for Status of the Active configuration.
radConverters	1.3.6.1.4.1.164.5
radDot1qPortVlanEntry	1.3.6.1.4.1.164.4.1.9.3.1		not-accessible	Information controlling VLAN configuration for a port. This is indexed by dot1dBasePort.
radDot1qPortVlanTable	1.3.6.1.4.1.164.4.1.9.3		not-accessible	A table containing control and status information for VLAN configuration per port.
radDXC10A	1.3.6.1.4.1.164.6.1.3.21
radDXC30	1.3.6.1.4.1.164.6.1.3.20
radDXC3000	1.3.6.1.4.1.164.6.1.3.24
radDXC30E	1.3.6.1.4.1.164.6.1.3.23
radDxc4	1.3.6.1.4.1.164.6.1.3.105
radDXC8R	1.3.6.1.4.1.164.6.1.3.22
radDXC8RNew	1.3.6.1.4.1.164.6.1.3.25
radEFcdIp	1.3.6.1.4.1.164.6.1.11.10
radEGate100	1.3.6.1.4.1.164.6.1.6.2
radEGate20	1.3.6.1.4.1.164.6.1.6.3
radEP4FL	1.3.6.1.4.1.164.6.1.9.5
radEP4T2FL	1.3.6.1.4.1.164.6.1.9.3
radEP4TAUI	1.3.6.1.4.1.164.6.1.9.2
radEP4TFL	1.3.6.1.4.1.164.6.1.9.4
radEP8T	1.3.6.1.4.1.164.6.1.9.1
radEPR4FL	1.3.6.1.4.1.164.6.1.9.11
radEPR4T2FL	1.3.6.1.4.1.164.6.1.9.9
radEPR4TAUI	1.3.6.1.4.1.164.6.1.9.8
radEPR4TFL	1.3.6.1.4.1.164.6.1.9.10
radEPR8T	1.3.6.1.4.1.164.6.1.9.7
radEthAccess	1.3.6.1.4.1.164.6.1.6
radETS4	1.3.6.1.4.1.164.6.1.7.7
radETS4fddiDAS	1.3.6.1.4.1.164.6.1.7.3
radETS4fddiSAS	1.3.6.1.4.1.164.6.1.7.4
radETX102	1.3.6.1.4.1.164.6.1.5.38
radETX102A	1.3.6.1.4.1.164.6.1.6.11
radETX102H	1.3.6.1.4.1.164.6.1.6.22
radETX105	1.3.6.1.4.1.164.6.1.5.44
radETX201	1.3.6.1.4.1.164.6.1.6.14
radETX201A	1.3.6.1.4.1.164.6.1.6.13
radETX202	1.3.6.1.4.1.164.6.1.5.43
radETX202A	1.3.6.1.4.1.164.6.1.6.12
radETX202AW	1.3.6.1.4.1.164.6.1.6.21
radETX202H	1.3.6.1.4.1.164.6.1.6.23
radETX205	1.3.6.1.4.1.164.6.1.5.45
radETX208	1.3.6.1.4.1.164.6.1.6.20
radETX510	1.3.6.1.4.1.164.6.1.6.1
radETX550	1.3.6.1.4.1.164.6.1.6.9
radFastWay100	1.3.6.1.4.1.164.6.1.4.28
radFcd155	1.3.6.1.4.1.164.6.1.3.90
radFcd155E	1.3.6.1.4.1.164.6.1.3.118
radFcd155ES	1.3.6.1.4.1.164.6.1.3.119
radFcd155EwAPS	1.3.6.1.4.1.164.6.1.3.130
radFcd155EwAPS2pdh	1.3.6.1.4.1.164.6.1.3.132
radFcd622	1.3.6.1.4.1.164.6.1.3.142
radFcdE1	1.3.6.1.4.1.164.6.1.3.31
radFcdE1A	1.3.6.1.4.1.164.6.1.3.37
radFcdE1I	1.3.6.1.4.1.164.6.1.3.32
radFcdE1L	1.3.6.1.4.1.164.6.1.3.29
radFcdE1LC	1.3.6.1.4.1.164.6.1.3.27
radFcdE1M	1.3.6.1.4.1.164.6.1.3.34
radFcdIP	1.3.6.1.4.1.164.6.1.3.35
radFcdIpD	1.3.6.1.4.1.164.6.1.11.11
radFcdIpL	1.3.6.1.4.1.164.6.1.11.13
radFcdIpM	1.3.6.1.4.1.164.6.1.11.12
radFcdIsdn	1.3.6.1.4.1.164.6.1.11.9
radFcdSTM	1.3.6.1.4.1.164.6.1.3.39
radFcdT1	1.3.6.1.4.1.164.6.1.3.30
radFcdT1A	1.3.6.1.4.1.164.6.1.3.36
radFcdT1L	1.3.6.1.4.1.164.6.1.3.28
radFcdT1LC	1.3.6.1.4.1.164.6.1.3.26
radFcdT1M	1.3.6.1.4.1.164.6.1.3.33
radFcdW	1.3.6.1.4.1.164.6.1.3.38
radFddi	1.3.6.1.4.1.164.2
radFdsl101	1.3.6.1.4.1.164.6.1.3.110
radFdsl201	1.3.6.1.4.1.164.6.1.3.111
radFDX100	1.3.6.1.4.1.164.6.1.2.1
radFEB4DAS	1.3.6.1.4.1.164.6.1.4.10
radFEB4FDX	1.3.6.1.4.1.164.6.1.4.22
radFEB4SAS	1.3.6.1.4.1.164.6.1.4.23
radFEC1	1.3.6.1.4.1.164.6.1.5.30
radFEC1UDP	1.3.6.1.4.1.164.6.1.5.33
radFEC2	1.3.6.1.4.1.164.6.1.5.32
radFEC2UDP	1.3.6.1.4.1.164.6.1.5.35
radFomiE3	1.3.6.1.4.1.164.6.1.3.72
radFomiT3	1.3.6.1.4.1.164.6.1.3.73
radFPS12	1.3.6.1.4.1.164.6.1.8.13
radFPS4	1.3.6.1.4.1.164.6.1.8.17
radFPS8	1.3.6.1.4.1.164.6.1.8.12
radFPS8c	1.3.6.1.4.1.164.6.1.8.16
radFRmon	1.3.6.1.4.1.164.6.1.3.80
radFTBDAS	1.3.6.1.4.1.164.6.1.4.26
radFTBSAS	1.3.6.1.4.1.164.6.1.4.27
radFTC1	1.3.6.1.4.1.164.6.1.5.10
radFTC1UDP	1.3.6.1.4.1.164.6.1.5.13
radFTC2	1.3.6.1.4.1.164.6.1.5.12
radFTC2UDP	1.3.6.1.4.1.164.6.1.5.15
radGen	1.3.6.1.4.1.164.6
radGmux2000	1.3.6.1.4.1.164.6.1.3.94
radGmux2004	1.3.6.1.4.1.164.6.1.3.149
radHcd4Sa	1.3.6.1.4.1.164.6.1.3.78
radHcdE1	1.3.6.1.4.1.164.6.1.3.52
radHcdE1Sa	1.3.6.1.4.1.164.6.1.3.51
radHtu2	1.3.6.1.4.1.164.6.1.3.43
radHtu2Sa	1.3.6.1.4.1.164.6.1.3.42
radHtuE1	1.3.6.1.4.1.164.6.1.3.41
radHtuE1Sa	1.3.6.1.4.1.164.6.1.3.40
radHtuE1SaV2	1.3.6.1.4.1.164.6.1.3.70
radHtuE1V2	1.3.6.1.4.1.164.6.1.3.71
radHtuT1	1.3.6.1.4.1.164.6.1.3.54
radHtuT1Sa	1.3.6.1.4.1.164.6.1.3.53
radImx2	1.3.6.1.4.1.164.6.1.3.62
radImx2T1E1	1.3.6.1.4.1.164.6.1.3.65
radImx4E1	1.3.6.1.4.1.164.6.1.3.64
radImx4T1	1.3.6.1.4.1.164.6.1.3.63
radImx64	1.3.6.1.4.1.164.6.1.3.60
radImx6L	1.3.6.1.4.1.164.6.1.3.61
radIMXI4	1.3.6.1.4.1.164.6.1.3.66
radIpMux1	1.3.6.1.4.1.164.6.1.3.82
radIpMux11	1.3.6.1.4.1.164.6.1.3.106
radIpMux116	1.3.6.1.4.1.164.6.1.3.115
radIpMux12	1.3.6.1.4.1.164.6.1.3.127
radIpMux14	1.3.6.1.4.1.164.6.1.3.107
radIpMux16	1.3.6.1.4.1.164.6.1.3.83
radIpMux1E	1.3.6.1.4.1.164.6.1.3.84
radIpMux216	1.3.6.1.4.1.164.6.1.3.147
radIpMux24	1.3.6.1.4.1.164.6.1.3.136
radIpMux2L	1.3.6.1.4.1.164.6.1.3.145
radIpMux4	1.3.6.1.4.1.164.6.1.3.81
radIpMux8	1.3.6.1.4.1.164.6.1.3.91
radKM2100	1.3.6.1.4.1.164.6.1.3.15
radKM2104	1.3.6.1.4.1.164.6.1.3.16
radLA104	1.3.6.1.4.1.164.6.1.13.3
radLA110	1.3.6.1.4.1.164.6.1.13.2
radLA130	1.3.6.1.4.1.164.6.1.13.4
radLA140	1.3.6.1.4.1.164.6.1.13.1
radLA210	1.3.6.1.4.1.164.6.1.13.5
radLA240	1.3.6.1.4.1.164.6.1.11.6
radLA240I	1.3.6.1.4.1.164.6.1.11.8
radLrs102	1.3.6.1.4.1.164.6.1.3.148
radLrs102unbal	1.3.6.1.4.1.164.6.1.3.150
radLrs12B	1.3.6.1.4.1.164.6.1.3.49
radLrs12F	1.3.6.1.4.1.164.6.1.3.48
radLrs16	1.3.6.1.4.1.164.6.1.3.151
radLrs22	1.3.6.1.4.1.164.6.1.3.143
radLrs52	1.3.6.1.4.1.164.6.1.3.50
radMBE1	1.3.6.1.4.1.164.6.1.4.5
radMBE1D	1.3.6.1.4.1.164.6.1.4.6
radMBE8	1.3.6.1.4.1.164.6.1.4.7
radMBE8D	1.3.6.1.4.1.164.6.1.4.8
radMBERAS	1.3.6.1.4.1.164.6.1.4.20
radMBERASa	1.3.6.1.4.1.164.6.1.4.21
radMdEntry	1.3.6.1.4.1.164.3.1.6.1.3.3.1		not-accessible	The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage
radMdTable	1.3.6.1.4.1.164.3.1.6.1.3.3		not-accessible	The MaintenanceDomain table. Each row in the table represents a different maintenance domain. A Maintenance domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance.
radMepCcStatusEntry	1.3.6.1.4.1.164.3.1.6.1.3.5.1		not-accessible	An entry in the CC Status Table.
radMepCcStatusTable	1.3.6.1.4.1.164.3.1.6.1.3.5		not-accessible	This table contains a list of CC Status received by a specific MEP from different Remote MEPs.
radMepEntry	1.3.6.1.4.1.164.3.1.6.1.3.1.1		not-accessible	An entry in the table.
radMepLtrEntry	1.3.6.1.4.1.164.3.1.6.1.3.4.1		not-accessible	The LinktraceReply table entry.
radMepLtrTable	1.3.6.1.4.1.164.3.1.6.1.3.4		not-accessible	This table contains a list of Linktrace replies received by a specific MEP in response to a linktrace message.
radMepTable	1.3.6.1.4.1.164.3.1.6.1.3.1		not-accessible	MEG End Point (MEP) configuration table associated with Maitenance Entity Group (MEG) End Point. MEP is a short name for an expanded ETH flow point that includes a compound ETH Segment flow termination function, which marks the end point of an ETH ME, and a compound ETH Diagnostic flow function.
radMiniCVS	1.3.6.1.4.1.164.6.1.3.154
radMiricE1T1	1.3.6.1.4.1.164.6.1.5.49
radMiricE3T3	1.3.6.1.4.1.164.6.1.5.50
radMlAtmE1	1.3.6.1.4.1.164.6.1.12.2.10
radMlAtmT1	1.3.6.1.4.1.164.6.1.12.2.11
radMLBT	1.3.6.1.4.1.164.6.1.4.9
radMP104	1.3.6.1.4.1.164.6.1.3.86
radMP204	1.3.6.1.4.1.164.6.1.3.87
radMP2100	1.3.6.1.4.1.164.6.1.3.1
radMP2100B	1.3.6.1.4.1.164.6.1.3.3
radMP2100F	1.3.6.1.4.1.164.6.1.3.4
radMP2100H	1.3.6.1.4.1.164.6.1.3.5
radMP2100VoIP	1.3.6.1.4.1.164.6.1.3.134
radMP2104	1.3.6.1.4.1.164.6.1.3.2
radMP2104H	1.3.6.1.4.1.164.6.1.3.6
radMP2104VoIP	1.3.6.1.4.1.164.6.1.3.135
radMP2200B	1.3.6.1.4.1.164.6.1.3.7
radMP2200F	1.3.6.1.4.1.164.6.1.3.8
radMP4100	1.3.6.1.4.1.164.6.1.3.120
radMX30	1.3.6.1.4.1.164.6.1.3.11
radMX300	1.3.6.1.4.1.164.6.1.3.12
radMX3000	1.3.6.1.4.1.164.6.1.3.9
radMX3004	1.3.6.1.4.1.164.6.1.3.10
radOp1550	1.3.6.1.4.1.164.6.1.3.108
radOp16E1L	1.3.6.1.4.1.164.6.1.3.95
radOp16E1LS	1.3.6.1.4.1.164.6.1.3.96
radOp25	1.3.6.1.4.1.164.6.1.3.139
radOp34E1	1.3.6.1.4.1.164.6.1.3.123
radOp4E1	1.3.6.1.4.1.164.6.1.3.103
radOp4E1LNew	1.3.6.1.4.1.164.6.1.3.116
radOp4E1NG1	1.3.6.1.4.1.164.6.1.3.137
radOp4T1	1.3.6.1.4.1.164.6.1.3.104
radOp4T1LNew	1.3.6.1.4.1.164.6.1.3.117
radOp4T1NG1	1.3.6.1.4.1.164.6.1.3.138
radOpt4E1C	1.3.6.1.4.1.164.6.1.3.74
radOpt4T1C	1.3.6.1.4.1.164.6.1.3.75
radOptimux155	1.3.6.1.4.1.164.6.1.3.67
radOptimux155DS3	1.3.6.1.4.1.164.6.1.3.92
radOptimux4E1	1.3.6.1.4.1.164.6.1.3.55
radOptimux4E1L	1.3.6.1.4.1.164.6.1.3.69
radOptimux4E1Mar06	1.3.6.1.4.1.164.6.1.3.129
radOptimux4E1V3dot5	1.3.6.1.4.1.164.6.1.3.128
radOptimux4T1	1.3.6.1.4.1.164.6.1.3.56
radOptimux4T1L	1.3.6.1.4.1.164.6.1.3.68
radOptimux4T1Mar06	1.3.6.1.4.1.164.6.1.3.131
radOptimuxT3	1.3.6.1.4.1.164.6.1.3.79
radOptimuxT3L	1.3.6.1.4.1.164.6.1.3.93
radOptimuxXL16E1	1.3.6.1.4.1.164.6.1.3.59
radOptimuxXLE1	1.3.6.1.4.1.164.6.1.3.57
radOptimuxXLT1	1.3.6.1.4.1.164.6.1.3.58
radOpXL16E1	1.3.6.1.4.1.164.6.1.3.102
radOpXLE1	1.3.6.1.4.1.164.6.1.3.100
radOpXLT1	1.3.6.1.4.1.164.6.1.3.101
radPrbiE3	1.3.6.1.4.1.164.6.1.3.76
radPrbiT3	1.3.6.1.4.1.164.6.1.3.77
radPRBm20	1.3.6.1.4.1.164.6.1.3.97
radPRBm22	1.3.6.1.4.1.164.6.1.3.98
radRADring	1.3.6.1.4.1.164.6.1.1.1
radRBHE	1.3.6.1.4.1.164.6.1.7.1
radRBHEEvents	1.3.6.1.4.1.164.6.1.7.1.0			The events for RAD Stackable products.
radRBHT	1.3.6.1.4.1.164.6.1.7.2
radRBHTEvents	1.3.6.1.4.1.164.6.1.7.2.0			The events for RAD Stackable products.
radRIC155	1.3.6.1.4.1.164.6.1.5.36
radRIC155GE	1.3.6.1.4.1.164.6.1.5.39
radRIC622GE	1.3.6.1.4.1.164.6.1.5.47
radRICE1	1.3.6.1.4.1.164.6.1.5.37
radRici155GE	1.3.6.1.4.1.164.6.1.6.18
radRici16	1.3.6.1.4.1.164.6.1.6.10
radRici4E1	1.3.6.1.4.1.164.6.1.6.6
radRici4E1L	1.3.6.1.4.1.164.6.1.6.16
radRici4T1	1.3.6.1.4.1.164.6.1.6.7
radRici622GE	1.3.6.1.4.1.164.6.1.6.19
radRici8E1	1.3.6.1.4.1.164.6.1.6.4
radRici8E1L	1.3.6.1.4.1.164.6.1.6.17
radRici8T1	1.3.6.1.4.1.164.6.1.6.5
radRiciE3	1.3.6.1.4.1.164.6.1.5.41
radRiciSE	1.3.6.1.4.1.164.6.1.5.46
radRiciT1	1.3.6.1.4.1.164.6.1.5.42
radRiciT3	1.3.6.1.4.1.164.6.1.5.40
radRingMonitor	1.3.6.1.4.1.164.6.1.1.3
radRouter	1.3.6.1.4.1.164.11
radRRFTBDAS	1.3.6.1.4.1.164.6.1.4.24
radRRFTBSAS	1.3.6.1.4.1.164.6.1.4.25
radRRMLBT	1.3.6.1.4.1.164.6.1.4.15
radRRMLBTF	1.3.6.1.4.1.164.6.1.4.16
radRRTRE1D	1.3.6.1.4.1.164.6.1.4.17
radRRTRE8	1.3.6.1.4.1.164.6.1.4.13
radRRTRE8D	1.3.6.1.4.1.164.6.1.4.14
radRTEC	1.3.6.1.4.1.164.6.1.11.3
radRTED	1.3.6.1.4.1.164.6.1.11.1
radRTEM	1.3.6.1.4.1.164.6.1.11.2
radSAH16Eext	1.3.6.1.4.1.164.6.1.7.12
radSAH16Eint	1.3.6.1.4.1.164.6.1.7.10
radSAH16Text	1.3.6.1.4.1.164.6.1.7.13
radSAH16Tint	1.3.6.1.4.1.164.6.1.7.11
radSAHEMU	1.3.6.1.4.1.164.6.1.7.8
radSAHEMX	1.3.6.1.4.1.164.6.1.7.5
radSAHTM	1.3.6.1.4.1.164.6.1.7.6
radSEC1	1.3.6.1.4.1.164.6.1.5.20
radSEC1UDP	1.3.6.1.4.1.164.6.1.5.23
radSEC2	1.3.6.1.4.1.164.6.1.5.22
radSEC2UDP	1.3.6.1.4.1.164.6.1.5.25
radSPH	1.3.6.1.4.1.164.6.1.5.48
radSPS12	1.3.6.1.4.1.164.6.1.8.5
radSPS2	1.3.6.1.4.1.164.6.1.8.1
radSPS3	1.3.6.1.4.1.164.6.1.8.2
radSPS3S	1.3.6.1.4.1.164.6.1.8.11
radSPS3Sc2S	1.3.6.1.4.1.164.6.1.8.15
radSPS3ScSL	1.3.6.1.4.1.164.6.1.8.14
radSPS4	1.3.6.1.4.1.164.6.1.8.18
radSPS6	1.3.6.1.4.1.164.6.1.8.3
radSPS9	1.3.6.1.4.1.164.6.1.8.4
radStarSwitch	1.3.6.1.4.1.164.6.1.12.1
radStarSwitchATM155	1.3.6.1.4.1.164.6.1.12.1.3
radStarSwitchATM25	1.3.6.1.4.1.164.6.1.12.1.1
radStarSwitchATM25L	1.3.6.1.4.1.164.6.1.12.1.2
radSTC1	1.3.6.1.4.1.164.6.1.5.1
radSTC1UDP	1.3.6.1.4.1.164.6.1.5.4
radSTC2	1.3.6.1.4.1.164.6.1.5.3
radSTC2UDP	1.3.6.1.4.1.164.6.1.5.6
radStkHub	1.3.6.1.4.1.164.7
radSuperLan	1.3.6.1.4.1.164.6.1.11.7
radSysAtm	1.3.6.1.4.1.164.6.1.12
radSysAtmEvents	1.3.6.1.4.1.164.6.1.12.0			The events for RAD ATM products.
radSysBRG	1.3.6.1.4.1.164.6.1.4
radSysCnvrtr	1.3.6.1.4.1.164.6.1.5
radSysEth	1.3.6.1.4.1.164.6.1.9
radSysFddi	1.3.6.1.4.1.164.6.1.2
radSysLA	1.3.6.1.4.1.164.6.1.13
radSysPS	1.3.6.1.4.1.164.6.1.8
radSysPSEvents	1.3.6.1.4.1.164.6.1.8.0			The events for RAD Packet Switch (PS) products.
radSysRtr	1.3.6.1.4.1.164.6.1.11
radSysRtrEvents	1.3.6.1.4.1.164.6.1.11.0			The events for RAD Router products.
radSysStkHub	1.3.6.1.4.1.164.6.1.7
radSysTerminal	1.3.6.1.4.1.164.6.1.100
radSysTR	1.3.6.1.4.1.164.6.1.1
radSysWan	1.3.6.1.4.1.164.6.1.3
radSysWanEvents	1.3.6.1.4.1.164.6.1.3.0			The events for RAD Wan products.
radTinyRouter	1.3.6.1.4.1.164.6.1.11.5
radTMA	1.3.6.1.4.1.164.6.1.1.2
radTokenRing	1.3.6.1.4.1.164.1
radTransport	1.3.6.1.4.1.164.6.4
radTransportDomains	1.3.6.1.4.1.164.6.4.1
radTransportDomainSnmpEfmOam	1.3.6.1.4.1.164.6.4.1.1			The SNMP over EFM OAM transport domain. The corresponding transport address is of type RadTransportAddressEfmOam for EFM OAM addresses (port).
radTRE1	1.3.6.1.4.1.164.6.1.4.1
radTRE1D	1.3.6.1.4.1.164.6.1.4.2
radTRE8	1.3.6.1.4.1.164.6.1.4.3
radTRE8D	1.3.6.1.4.1.164.6.1.4.4
radTRERAS	1.3.6.1.4.1.164.6.1.4.18
radTRERASa	1.3.6.1.4.1.164.6.1.4.19
radTrimBrg10	1.3.6.1.4.1.164.6.1.4.11
radTrimBrg16	1.3.6.1.4.1.164.6.1.4.12
radUNT20E1	1.3.6.1.4.1.164.6.1.3.144
radUNT20Fcd	1.3.6.1.4.1.164.6.1.3.146
radUNT20Ric	1.3.6.1.4.1.164.6.1.6.15
radVmux110	1.3.6.1.4.1.164.6.1.3.88
radVmux120	1.3.6.1.4.1.164.6.1.3.112
radVmux210	1.3.6.1.4.1.164.6.1.3.122
radVmux2100	1.3.6.1.4.1.164.6.1.3.85
radVmux2200	1.3.6.1.4.1.164.6.1.3.113
radVmux312	1.3.6.1.4.1.164.6.1.3.124
radVmux314	1.3.6.1.4.1.164.6.1.3.141
radVmux320	1.3.6.1.4.1.164.6.1.3.133
radVmux400	1.3.6.1.4.1.164.6.1.3.114
radVmux404	1.3.6.1.4.1.164.6.1.3.125
radVmux405	1.3.6.1.4.1.164.6.1.3.152
radVmux420	1.3.6.1.4.1.164.6.1.3.126
radVmux425	1.3.6.1.4.1.164.6.1.3.153
radVOIP	1.3.6.1.4.1.164.6.1.3.13
radWan	1.3.6.1.4.1.164.3
radWebRanger	1.3.6.1.4.1.164.6.1.11.4
NTF remoteConnStatusTrap	1.3.6.1.4.1.164.6.1.3.0.14			This trap is sent upon a change in Remote connectivity of Bundle connection.
ripSapIfConfEntry	1.3.6.1.4.1.164.11.7.2.3.4.1		not-accessible	A Single Routing Domain in a single Subnet.
ripSapIfConfTable	1.3.6.1.4.1.164.11.7.2.3.4		not-accessible	A list of Interfaces which require separate configuration in RIP/SAP.
rowInfoEntry	1.3.6.1.4.1.164.6.2.43.1		not-accessible	An entry in the table.
rowInfoTable	1.3.6.1.4.1.164.6.2.43		not-accessible	This table holds information of other tables.
rtrBridge	1.3.6.1.4.1.164.11.7
NTF sanityCheckTrap	1.3.6.1.4.1.164.3.3.0.1			This trap is sent after a data base download attempt. It returns the sanity result status and the configuration no.checked.
NTF sanityTrap	1.3.6.1.4.1.164.3.2.0.2			This trap is sent after a data base update. It returns the sanity result status and the configuration no. checked. If the result is of Flip DB Sanity Check, the configuration no. sent will be 0. If the result is of Variant Sanity Check, the configuration no. sent will be 100.
schedXEntry	1.3.6.1.4.1.164.6.2.14.5.1		not-accessible	An entry in the table.
schedXTable	1.3.6.1.4.1.164.6.2.14.5		not-accessible	An Augment to the Schedule table (schedTable in DISMAN-SCHEDULE-MIB; RFC-3231).
serviceEntry	1.3.6.1.4.1.164.6.3.6.1		not-accessible	An entry in the Service Table.
services	1.3.6.1.4.1.164.6.3
serviceStatEntry	1.3.6.1.4.1.164.6.3.8.1		not-accessible	An entry in the Service Statistics Table.
serviceStatTable	1.3.6.1.4.1.164.6.3.8		not-accessible	Service statistics table.
serviceTable	1.3.6.1.4.1.164.6.3.6		not-accessible	Table of services.
statAgnGen	1.3.6.1.4.1.164.3.1.2.1
statisPrtGen	1.3.6.1.4.1.164.3.1.4.1.3
statMdlGen	1.3.6.1.4.1.164.3.1.3.1
statMdlMux	1.3.6.1.4.1.164.3.2.2.2
statPrtGen	1.3.6.1.4.1.164.3.1.4.1
statPrtMux	1.3.6.1.4.1.164.3.2.3.1
NTF statusChangedTrap	1.3.6.1.4.1.164.3.2.0.5			This trap is sent upon any change of the LEDs status.
NTF successfulLogin	1.3.6.1.4.1.164.6.1.0.24			This trap is sent when a user performed successful Login via Terminal/Telnet/Web. This trap is used when the device is located at End-User's premises while management is at Service Provider's premises.
swdlStatusEntry	1.3.6.1.4.1.164.6.2.12.11.1		not-accessible	An entry in table.
NTF swdlStatusResult	1.3.6.1.4.1.164.6.1.0.4			This notification is sent when Software Down Load is finished. The attached object indicates the File Name.
swdlStatusTable	1.3.6.1.4.1.164.6.2.12.11		not-accessible	This parameters table is for software download status. It also includes data about the files down-loaded or attempted to be down-loaded.
NTF sysAlrStatusTrap	1.3.6.1.4.1.164.3.3.0.4			This trap is sent upon any change in the value of any of the variables.
sysBufferAlr	1.3.6.1.4.1.164.3.3.1.5
sysBufferAlrEntry	1.3.6.1.4.1.164.3.3.1.5.1.1		not-accessible	An entry in table.
sysBufferAlrTable	1.3.6.1.4.1.164.3.3.1.5.1		not-accessible	List of current existing alarms (of all levels).
sysCClkSrcEntry	1.3.6.1.4.1.164.3.3.1.6.1.1		not-accessible	An entry in table.
sysCClkSrcTable	1.3.6.1.4.1.164.3.3.1.6.1		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. For devices with more than one configuration: The write operation into the Table Objects is valid only for the TmpCnfg entry.
sysChas	1.3.6.1.4.1.164.3.3.1.2.1
sysCnfgEntry	1.3.6.1.4.1.164.3.3.1.6.2.1		not-accessible	An entry in table.
sysCnfgTable	1.3.6.1.4.1.164.3.3.1.6.2		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
sysConfig	1.3.6.1.4.1.164.3.3.1.6
sysCRdnEntry	1.3.6.1.4.1.164.3.3.1.6.3.1		not-accessible	An entry in table.
sysCRdnTable	1.3.6.1.4.1.164.3.3.1.6.3		not-accessible	Configuration of all Redundant I/O cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that have no Redundancy, will not exist in this table.
sysCurrentAlr	1.3.6.1.4.1.164.3.3.1.4
sysDbase	1.3.6.1.4.1.164.3.3.1.7
sysDbaseFlipEntry	1.3.6.1.4.1.164.3.3.1.7.4.1		not-accessible	An entry in table.
sysDbaseFlipTable	1.3.6.1.4.1.164.3.3.1.7.4		not-accessible	Dbase Flip time and activation for every configuration.
sysDcl	1.3.6.1.4.1.164.3.3.1.2.2
sysDclCopyDbEntry	1.3.6.1.4.1.164.3.3.1.2.2.3.1		not-accessible	An entry in table.
sysDclCopyDbTable	1.3.6.1.4.1.164.3.3.1.2.2.3		not-accessible	This table enables to copy a cofiguration from the Offline Dcl to the Online Dcl.
sysDclEntry	1.3.6.1.4.1.164.3.3.1.2.2.1.1		not-accessible	An entry in table.
sysDclTable	1.3.6.1.4.1.164.3.3.1.2.2.1		not-accessible	All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
sysHub	1.3.6.1.4.1.164.3.3.1.2
NTF sysRedundancyActiveCardTrap	1.3.6.1.4.1.164.3.3.0.8			The trap is sent upon change of Active Main/CL Card.
NTF sysRedundancyActivePortTrap	1.3.6.1.4.1.164.3.3.0.9			The trap is sent upon change of Active Port of Redundancy Group.
NTF sysRedundancyStatusTrap	1.3.6.1.4.1.164.3.3.0.7			The trap is sent upon change in Redundancy Status.
sysSa	1.3.6.1.4.1.164.3.3.1.1
sysSAlrEntry	1.3.6.1.4.1.164.3.3.1.4.1.1		not-accessible	An entry in table.
sysSAlrTable	1.3.6.1.4.1.164.3.3.1.4.1		not-accessible	List of system level current existing alarms .
sysSBusEntry	1.3.6.1.4.1.164.3.3.1.3.21.1		not-accessible	An entry in table.
sysSBusTable	1.3.6.1.4.1.164.3.3.1.3.21		not-accessible	This table includes data and status about the internal DXC BUS.
sysSErrListEntry	1.3.6.1.4.1.164.3.3.1.3.13.1		not-accessible	An entry in table.
sysSErrListTable	1.3.6.1.4.1.164.3.3.1.3.13		not-accessible	A table.
sysSRdnCmdEntry	1.3.6.1.4.1.164.3.3.1.3.22.1		not-accessible	An entry in table.
sysSRdnCmdTable	1.3.6.1.4.1.164.3.3.1.3.22		not-accessible	This table includes commands used for IO Redundancy.
sysSRdnFlipEntry	1.3.6.1.4.1.164.3.3.1.3.18.1		not-accessible	An entry in table.
sysSRdnFlipTable	1.3.6.1.4.1.164.3.3.1.3.18		not-accessible	This table includes all the Flip events due to I/O Redundancy since last Clear command of this table.
sysStatus	1.3.6.1.4.1.164.3.3.1.3
NTF sysStatusChangedTrap	1.3.6.1.4.1.164.3.3.0.5			This trap is sent when Leds status is changed.
systemDacsMux	1.3.6.1.4.1.164.3.3.1
systemInterface	1.3.6.1.4.1.164.6.2.35
systemModule	1.3.6.1.4.1.164.6.2.32
systemNtp	1.3.6.1.4.1.164.6.2.14.4
systemOam	1.3.6.1.4.1.164.6.2.36
systemOamDescrEntry	1.3.6.1.4.1.164.6.2.36.2.1		not-accessible	An entry in the OAM table.
systemOamDescrTable	1.3.6.1.4.1.164.6.2.36.2		not-accessible	The OAM Descriptors Configuration Table.
systemOamEntry	1.3.6.1.4.1.164.6.2.36.1.1		not-accessible	An entry in the OAM table.
systemOamTable	1.3.6.1.4.1.164.6.2.36.1		not-accessible	The OAM Configuration Table.
systemPort	1.3.6.1.4.1.164.6.2.15
systemPsEntry	1.3.6.1.4.1.164.6.2.25.1		not-accessible	An entry in table.
systemPsTable	1.3.6.1.4.1.164.6.2.25		not-accessible	This table describes the PS types of a device. Usage of this table is specified in the device's NMS SRS
systems	1.3.6.1.4.1.164.6.1
systemsEvents	1.3.6.1.4.1.164.6.1.0			The events for RAD products.
systemTiming	1.3.6.1.4.1.164.6.2.14
NTF systemTrap	1.3.6.1.4.1.164.6.1.3.0.6			This trap alerts of major problems in the device.
systemVoice	1.3.6.1.4.1.164.3.1.2.12
systemVoiceCoderEntry	1.3.6.1.4.1.164.3.1.2.12.2.1		not-accessible	An entry in Voice Coders table.
systemVoiceCoderTable	1.3.6.1.4.1.164.3.1.2.12.2		not-accessible	Voice Coders table.
systemVoiceEntry	1.3.6.1.4.1.164.3.1.2.12.1.1		not-accessible	An entry in table.
systemVoiceTable	1.3.6.1.4.1.164.3.1.2.12.1		not-accessible	General Parameters for voice - system level.
NTF tftpStatusChangeTrap	1.3.6.1.4.1.164.6.1.0.1			This trap is sent whenever the status of tftp changed.
trapEntry	1.3.6.1.4.1.164.6.2.11.1		not-accessible	An entry in trapTable.
trapTable	1.3.6.1.4.1.164.6.2.11		not-accessible	This table may include the last few traps generated by the agent, for future retrieval. The table has a limited capacity. If traps are not retrieved in proper time, they will be over-written by new traps. For other devices, it can include generic variables that will be attached to traps as 'accessible-for-notify'.
unknown	1.3.6.1.4.1.164.6.1.7.9
wanGen	1.3.6.1.4.1.164.3.1
webranger	1.3.6.1.4.1.164.11.7.2
wfq	1.3.6.1.4.1.164.6.3.1
wfqEntry	1.3.6.1.4.1.164.6.3.1.1.1		not-accessible	An entry in the Weighted Fair Queueing table.
wfqTable	1.3.6.1.4.1.164.6.3.1.1		not-accessible	This table allows user to define several WFQ tables per output port. WFQ supports flows with different bandwidth requirements by giving each queue a weight that assigns it a different percentage of output port bandwidth. When Weighted Fair Queuing is used, it is possible to precisely attribute bandwidth partitioning among the queues. When there is congestion, each class (queue) is not allowed to use more bandwidth than the amount allocated to it.
wrConfigIpDhcp	1.3.6.1.4.1.164.11.7.2.2.1
wrConfigIpDNS	1.3.6.1.4.1.164.11.7.2.2.2
wrConfigIpxRouterInfo	1.3.6.1.4.1.164.11.7.2.3
wrDhcpEntry	1.3.6.1.4.1.164.11.7.2.2.1.2.1		not-accessible	DHCP parameters per entry of the DHCP table.
wrDhcpTable	1.3.6.1.4.1.164.11.7.2.2.1.2		not-accessible	A list of DHCP entries. The number of entries is up to DHCP current entries, according to the WEBRANger model.
wrFrCnfgEntry	1.3.6.1.4.1.164.11.7.2.4.5.1		not-accessible	Configuration entry for Fr parameters that do not exist in RFC2115.
wrFrCnfgTable	1.3.6.1.4.1.164.11.7.2.4.5		not-accessible	Configuration table for Fr parameters that do not exist in RFC2115.
wrInterface	1.3.6.1.4.1.164.11.7.2.4
wrIpAddressEntry	1.3.6.1.4.1.164.11.7.2.4.1.1		not-accessible	Ip Address per Link
wrIpAddressTable	1.3.6.1.4.1.164.11.7.2.4.1		not-accessible	Link IP addresses Table.
wrIpRouterInfo	1.3.6.1.4.1.164.11.7.2.2
wrLanIfEntry	1.3.6.1.4.1.164.11.7.2.4.3.1		not-accessible	Ip Address per Link
wrLanIfTable	1.3.6.1.4.1.164.11.7.2.4.3		not-accessible	Link IP addresses Table.
wrLanIpxNetEntry	1.3.6.1.4.1.164.11.7.2.3.2.1		not-accessible	IPX Nets per frame type & LAN port. The table entries will be created by the agent
wrLanIpxNetTable	1.3.6.1.4.1.164.11.7.2.3.2		not-accessible	Lan IPX nets Table.
wrSpoofingEntry	1.3.6.1.4.1.164.11.7.2.4.2.1		not-accessible	Spoofing per Link
wrSpoofingTable	1.3.6.1.4.1.164.11.7.2.4.2		not-accessible	Spoofing Table.
wrSyncCnfgEntry	1.3.6.1.4.1.164.11.7.2.4.4.1		not-accessible	Configuration table
wrSyncCnfgTable	1.3.6.1.4.1.164.11.7.2.4.4		not-accessible	Configuration table for Async interface.
wrSysConfig	1.3.6.1.4.1.164.11.7.2.1
xcEntry	1.3.6.1.4.1.164.6.2.31.1		not-accessible	An entry in table.
xcTable	1.3.6.1.4.1.164.6.2.31		not-accessible	Configuration of system cross-connect entries. The table follows the behavior described in RFC 2515, RFC 1604 regarding the creation deletion and modification of an entry within the table.
NTF xModemFileTransferStatusTrap	1.3.6.1.4.1.164.6.1.0.22			This trap is sent in the following cases: - When an xModem File Transfer Session begins. In this case, the trapVal.1 string sent will be: 'Start'. - When an xModem File Transfer Session ends. In this case, the trapVal.1 string sent will be one of the following, according to the way the session ended : - 'End: OK' - 'End: Failed'

RFC description

RAD Data Communications enterprise MIB for WAN access device management.

Start monitoring RAD Data Communications access/transmission/multiplexer equipment, entire product line (base enterprise MIB) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RAD-MIB

This MIB depends on

Related MIBs

What Is RAD-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description