All MIBs › RAD-MIB › prtGenParamStatus
prtGenParamStatus
Module: RAD-MIB
OID (symbolic): RAD-MIB::prtGenParamStatus
OID (numeric): 1.3.6.1.4.1.164.3.3.3.1.1.1.15
Node type: OBJECT-TYPE
Type: OCTET STRING
Access: read-only
Description:
This object indicates Status of parameters specific to the
selected port.
- For a port that has no special status or is supported
by prtSExHsfStatTable - 1 Octet: 00hex
- For HS cards (Dxc cards) - 1 octet:
Bit 7 (MSB)..Bit 2 = 0 (NA)
Bit 0 and 1 indicates RTS control signal state:
Bit 1: '1'=active ; '0'=notActive
Bit 0 (LSB): '1'=unknown ; '0'=NA
- For HS-U/1 external port (MP card, used in FCD-M) - 1 Octet:
Bit 7 6 5 4 3 2 1 0 LSB
|________| |__| |__|
spare modem sync
modem: 00 = other sync: 00 = not sync
01 = unknown 01 = sync
10 = ASMi-31/2 10 = reserved
11 = reserved 11 = reserved
- For VC-6, VC-12, VC-12/6 external ports - 1 Octet :
Bit 7 (MSB)..Bit 2 = 0 (NA)
Bit 1: Tx Signaling '1'=On ; '0'=Off
Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off
- For VC-2/R2(FXS) external ports - 1 Octet :
Bit - 7 6 5 4 3 2 1 0
|_| |_________|
Call Call State
Direction
Bit 7 (MSB) and Bit 6 : Call Direction
00 - Incoming
01 - Outgoing
Bit 5..Bit 0: Call State
000000 - Idle
000001 - Seized
000010 - Both-Way Conflict
000011 - Seizure Ack
000100 - Answered
000101 - Clear Backward
000110 - Clear Forward
000111 - Blocked
001000 - Fault
001001 - Fault 3
001010 - Fault 4
001011 - Fault 5
001100 - Fault 6
001101 - Fault 7
- For ML-20 external port - 3 Octets :
- 1 MS Octet will represent the Real Rate used:
Bit - 7 6 5 4 3 2 1 0
|___| |_______|
spare Rate
Valid values: 0..31, meaning 0..31x64Kbps
Invalid values: 32..255.
- 2 LS Octets will represent the Status of 7 Control
Signals:
Signal - --- CTS DSR DCD RJ TM DTR RTS
Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Octet - 2 3 (LS)
'---' will always have the value 00
Rest of the Signals (2 bits each) can have the following
values:
00=NA ; 01=Unused ; 10=Off ; 11=On
- For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet
Bit - 7 6 5 4 3 2 1 0
|___________|
spare Mode of Operation
Mode of Operation: '1'=Central ; '0'=Remote
- For KM2100, KVF.5 cards - indicates the status of A and B signaling
for each internal channel.
1 Octet:
Bit - 7 6 5 4 3 2 1 0
|_____| |_| |_|
spare B A
Bit 0 (LSB) and Bit 1 : A status
Bit 2 and Bit 3 : B status
00 - Off
01 - On
11 - Unknown
- For FCD-W, NETWORK and USER ports - 1 Octet
Status of Control Signals: '1'=On ; '0'=Off or when not applicable
Bit - 7 6 5 4 3 2 1 0
Bit 7 (MSB) - Signal Loss (applicable only for G.703 interface)
Bit 6 - CONTROL (applicable only for X.21 interface)
Bit 5 - INDICATION (applicable only for X.21 interface)
Bit 4 - DSR (applicable only for V.35 interface)
Bit 3 - RTS (applicable only for V.35 interface)
Bit 2 - CTS (applicable only for V.35 interface)
Bit 1 - DTR (applicable only for V.35 interface)
Bit 0 - DCD (applicable only for V.35 interface)
- For DXC R6 , D8U, D16U External ports - 1 Octet
Bit 7 6 5 4 3 2 1 0 LSB
|________| |__| |__|
spare modem sync
modem: 00 = other sync: 00 = not sync
01 = unknown 01 = sync
10 = ASMi-31/2 10 = reserved
11 = reserved 11 = reserved
- For DXC DE1-HDSL, DT1-HDSL, D16GSDSL, D8SL External ports - 2 Octets
MSB octet: far-end modem channel interface
LSB octet: Sub Link existence (Y/N), far-end modem type,
synchronization with far-end modem
MSB octet: 0000 0000 = no interface
0000 0001 = db15 (X21)
0000 0010 = IR-IP
0000 0011 = IR-ETH-Q
0000 0100 = V35
0000 0101 = ETH-RJ45
0000 0110 = G703
0000 0111 = db25 (RS530)
0000 1000 = ETH-BNC
0000 1001 = E1(Balanced)
0000 1010 = E1(Unbalanced)
0000 1011 = IR-ETH-QN
Rest of the combinations: reserved
LSB octet:
Bit 7 6 5 4 3 2 1 0 LSB
| |___________| |__|
SL modem sync
or Box material
SL: modem: 00000 = other sync: 00 = not sync
0=not exist 00001 = unknown 01 = sync
1=exists 00010 = ASMi-31/2 10 = reserved
00011 = HCD-E1 11 = reserved
Box material 00100 = HTU-E1
(for D8SL card): 00101 = HTU-2
0=metal 00110 = ASMi-52 SA/2W/Slave
1=plastic 00111 = ASMi-52 SA/2W/Master
01000 = ASMi-52/CQ card of LRS-24
01001 = ASMi-52/CD card of LRS-24
01010 = D16GSDSL card of DXC-3000
01011 = LRS-52
01100 = FCD
01110 = D8GSDSL card of DXC-3000
01111 = ASMi-52A
Rest = reserved Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.164.3.3.3.1.1.1.15 snmpwalk -v2c -c public <target> RAD-MIB::prtGenParamStatus
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.164.3.3.3.1.1.1.15.1 snmpget -v2c -c public <target> RAD-MIB::prtGenParamStatus.1
OID Breakdown
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | BIANCA-BRICK-PPP-MIB |
| 1.3.6 | dod | BIANCA-BRICK-PPP-MIB |
| 1.3.6.1 | internet | BIANCA-BRICK-PPP-MIB |
| 1.3.6.1.4 | private | BIANCA-BRICK-PPP-MIB |
| 1.3.6.1.4.1 | enterprises | ANIROOT-MIB |
| 1.3.6.1.4.1.164 | rad | DACS-MIB |
| 1.3.6.1.4.1.164.3 | radWan | DACS-MIB |
| 1.3.6.1.4.1.164.3.3 | dacsMux | DACS-MIB |
| 1.3.6.1.4.1.164.3.3.3 | prtDacsMux | DACS-MIB |
| 1.3.6.1.4.1.164.3.3.3.1 | prtGen | DACS-MIB |
| 1.3.6.1.4.1.164.3.3.3.1.1 | prtGenParamTable | DACS-MIB |
| 1.3.6.1.4.1.164.3.3.3.1.1.1 | prtGenEntry | DACS-MIB |
| 1.3.6.1.4.1.164.3.3.3.1.1.1.15 | prtGenParamStatus | RAD-MIB |