All MIBs › RAD-MIB › prtSParamStatus
prtSParamStatus
Module: RAD-MIB
OID (symbolic): RAD-MIB::prtSParamStatus
OID (numeric): 1.3.6.1.4.1.164.3.1.4.1.1.1.15
Node type: OBJECT-TYPE
Type: OCTET STRING
Access: read-only
Description:
This object indicates Status of parameters specific to the
selected port.
- For a port that has no special status or is supported
by prtSExHsfStatTable - 1 Octet: 00hex
- For VC-6, VC-6A, VC-6AG, VC-6A/4LB, VC-12, VC-12/6, external ports - 1 Octet :
Bit 7 (MSB)..Bit 2 = 0 (NA)
Bit 1: Tx Signaling '1'=On ; '0'=Off
Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off
- For VC-2/R2(FXS) external ports - 1 Octet :
Bit - 7 6 5 4 3 2 1 0
|_| |_________|
Call Call State
Direction
Bit 7 (MSB) and Bit 6 : Call Direction
00 - Incoming
01 - Outgoing
Bit 5..Bit 0: Call State
000000 - Idle
000001 - Seized
000010 - Both-Way Conflict
000011 - Seizure Ack
000100 - Answered
000101 - Clear Backward
000110 - Clear Forward
000111 - Blocked
001000 - Fault
001001 - Fault 3
001010 - Fault 4
001011 - Fault 5
001100 - Fault 6
001101 - Fault 7
- For ML-20 external port - 3 Octets :
- 1 MS Octet will represent the Real Rate used:
Bit - 7 6 5 4 3 2 1 0
|___| |_______|
spare Rate
Valid values: 0..31, meaning 0..31x64Kbps
Invalid values: 32..255.
- 2 LS Octets will represent the Status of 7 Control
Signals:
Signal - --- CTS DSR DCD RJ TM DTR RTS
Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Octet - 2 3 (LS)
'---' will always have the value 00
Rest of the Signals (2 bits each) can have the following
values:
00=NA ; 01=unused ; 10=Off ; 11=On
- For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet
Bit - 7 6 5 4 3 2 1 0
|___________|
spare Mode of Operation
Mode of Operation: '1'=Central ; '0'=Remote
- For ACM external port - 1 Octet
Bit - 7 6 5 4 3 2 1 0
|_________|
spare Alarm State
Alarm State: according to bits 1,0:
00=NA ; 01=unused ; 10=Off ; 11=On
- For HS-U/1 external port - 1 Octet
Bit 7 6 5 4 3 2 1 0 LSB
|________| |__| |__|
spare modem sync
modem: 00 = other sync: 00 = not sync
01 = unknown 01 = sync
10 = ASMi-31/2 10 = reserved
11 = reserved 11 = reserved
- For MTML-2/4 external ports, ML-8 externalports, ML-IP (MTML-IP)
internal ports and MTML-E2 internal ports - 1 Octet :
Bit 7 6 5 4 3 2 1 0 LSB
|
BERT State
BERT State (Bit 0):
0 = OFF (BERT is not running on this port or any of its TSs/Bits)
1 = ON (BERT is running on this port OR on one of its TSs/Bits)
- For ML-20N external ports - 4 Octets
- 1 MS Octet will represent the Actual Link Rate:
Bit - 7 6 5 4 3 2 1 0
|_| |_________|
spare Rate
Valid values: 0..34, meaning:
0..32 = (0..32)x64Kbps
33 = Invalid Rate
34 = not applicable (when Rate is not Auto)
35 = 0 Kbps
Invalid values: 36..255.
- 2 middle Octets will represent the Status of 4 Control
Signals:
- LS Octet - Bits 3-0: RTS/C (Command, for X.21 interface)
Bits 7-4: DCD/I (Indication for X.21 interface)
- MS Octet - Bits 3-0: DTR
Bits 7-4: DSR
Each 4 Bits are divided as follows:
- 2 MS bits: DCE
- 2 LS bits: DTE
For each 2 bits (DCE/DTE):
00=NA ; 01=unused ; 10=Off ; 11=On.
- LS Octet: (as for MTML-2):
Bit 7 6 5 4 3 2 1 0 LSB
|
BERT State
BERT State (Bit 0):
0 = OFF (BERT is not running on this port or any of its TSs/Bits)
1 = ON (BERT is running on this port OR on one of its TSs/Bits)
- For MP-2100/2200 MSL-4/E1, MSL-8/E1 External ports - 3 Octets
- MS octet: far-end modem channel interface
- Middle octet: Material (plastic/metal), far-end modem type,
synchronization with far-end modem
- LS octet: BERT state (at port/TS/Bit level)
- MS octet: 0000 0000 = no interface
0000 0001 = db15 (X21)
0000 0010 = IR-IP
0000 0011 = IR-ETH-Q
0000 0100 = V35
0000 0101 = ETH-RJ45
0000 0110 = G703
0000 0111 = db25 (RS530)
0000 1000 = ETH-BNC
0000 1001 = E1(Balanced)
0000 1010 = E1(Unbalanced)
0000 1011 = IR-ETH-QN
Rest of the combinations: reserved
- Middle octet:
Bit 7 6 5 4 3 2 1 0 LSB
| |___________| |__|
Box material modem sync
Box material modem: 00000 = other sync: 00 = not sync
(for ASMi-52 SA) 00001 = unknown 01 = sync
0=metal 00010 = reserved 10 = reserved
1=plastic 00011 = reserved 11 = reserved
00100 = reserved
00101 = reserved
00110 = ASMi-52 SA/2W/Slave
00111 = ASMi-52 SA/2W/Master
01000 = ASMi-52/CQ card of LRS-24
01001 = ASMi-52/CD card of LRS-24
01010 = D16GSDSL card of DXC-3000
01011 = LRS-52
01100 = FCD-IP
01101 = FCD-IPM
01110 = D8SL card of DXC-30
01111 = ASMi-52A
10000 = MP card (SHDSL)
10001 = ASMi-52L
Rest = reserved
- LS Octet: (as for MTML-2):
Bit 7 6 5 4 3 2 1 0 LSB
|
BERT State
BERT State (Bit 0):
0 = OFF (BERT is not running on this port or any of its TSs)
1 = ON (BERT is running on this port OR on one of its TSs)
- For MP-4100 MSL card Links - 4 Octets
- MS octet: far-end modem DTE2 interface (same as for MP-2100 MSL cards)
- after MS octet: far-end modem DTE1 interface (same as for MP-2100 MSL cards)
- before LS octet: Material (plastic/metal), far-end modem type,
synchronization with far-end modem (same as for MP-2100 MSL cards)
- LS octet: BERT state (at port/TS/Bit level)- same as for MP-2100 MSL cards
- For MP-4100, LRS-102 OP-108/106 Links - 3 Octets
- MS octet: far-end PS type and state
- Middle octet: synchronization with far-end device
- LS octet: BERT state (at port/TS level) - same as for MP-2100 MSL cards
- MS octet:
Bit 7 6 5 4 3 2 1 0 LSB
|__| |__| |__| |__|
PS-A PS-A PS-B PS-B
PS Type PS State PS Type PS State
00=None 00=None
01=AC-DC 01=OK
10=DC 10=Fail
- Middle octet:
Bit 7 6 5 4 3 2 1 0 LSB
|__|
sync:
00 = not sync
01 = sync
10 = reserved
11 = reserved
Rest = reserved
What is prtSParamStatus?
This OID holds raw status data (as a sequence of bytes) describing the current state of port or service parameters. The exact meaning depends on the device implementation. A technician would read this value when diagnosing port configuration issues to see the raw parameter state that affects link behavior.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.164.3.1.4.1.1.1.15 snmpwalk -v2c -c public <target> RAD-MIB::prtSParamStatus
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.164.3.1.4.1.1.1.15.1 snmpget -v2c -c public <target> RAD-MIB::prtSParamStatus.1
SNMPv3 example:
snmpget -v3 -l authPriv -u snmpv3-user -a SHA -A "AuthPassword1" -x AES -X "PrivPassword1" <target> prtSParamStatus.1
OID Breakdown
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | BIANCA-BRICK-PPP-MIB |
| 1.3.6 | dod | BIANCA-BRICK-PPP-MIB |
| 1.3.6.1 | internet | BIANCA-BRICK-PPP-MIB |
| 1.3.6.1.4 | private | BIANCA-BRICK-PPP-MIB |
| 1.3.6.1.4.1 | enterprises | ANIROOT-MIB |
| 1.3.6.1.4.1.164 | rad | DACS-MIB |
| 1.3.6.1.4.1.164.3 | radWan | DACS-MIB |
| 1.3.6.1.4.1.164.3.1 | wanGen | DACS-MIB |
| 1.3.6.1.4.1.164.3.1.4 | prtWanGen | DACS-MIB |
| 1.3.6.1.4.1.164.3.1.4.1 | statPrtGen | DACS-MIB |
| 1.3.6.1.4.1.164.3.1.4.1.1 | prtSInstTable | DACS-MIB |
| 1.3.6.1.4.1.164.3.1.4.1.1.1 | prtSInstEntry | DACS-MIB |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.15 | prtSParamStatus | RAD-MIB |