RAD-MIB (page 2 of 2) - SNMP MIB Browser

OID symbolic	OID numeric	Type	Access	Description
radMiricE3T3	1.3.6.1.4.1.164.6.1.5.50
radEthAccess	1.3.6.1.4.1.164.6.1.6
radETX510	1.3.6.1.4.1.164.6.1.6.1
radEGate100	1.3.6.1.4.1.164.6.1.6.2
radEGate20	1.3.6.1.4.1.164.6.1.6.3
radRici8E1	1.3.6.1.4.1.164.6.1.6.4
radRici8T1	1.3.6.1.4.1.164.6.1.6.5
radRici4E1	1.3.6.1.4.1.164.6.1.6.6
radRici4T1	1.3.6.1.4.1.164.6.1.6.7
radETX550	1.3.6.1.4.1.164.6.1.6.9
radRici16	1.3.6.1.4.1.164.6.1.6.10
radETX102A	1.3.6.1.4.1.164.6.1.6.11
radETX202A	1.3.6.1.4.1.164.6.1.6.12
radETX201A	1.3.6.1.4.1.164.6.1.6.13
radETX201	1.3.6.1.4.1.164.6.1.6.14
radUNT20Ric	1.3.6.1.4.1.164.6.1.6.15
radRici4E1L	1.3.6.1.4.1.164.6.1.6.16
radRici8E1L	1.3.6.1.4.1.164.6.1.6.17
radRici155GE	1.3.6.1.4.1.164.6.1.6.18
radRici622GE	1.3.6.1.4.1.164.6.1.6.19
radETX208	1.3.6.1.4.1.164.6.1.6.20
radETX202AW	1.3.6.1.4.1.164.6.1.6.21
radETX102H	1.3.6.1.4.1.164.6.1.6.22
radETX202H	1.3.6.1.4.1.164.6.1.6.23
radSysStkHub	1.3.6.1.4.1.164.6.1.7
radRBHE	1.3.6.1.4.1.164.6.1.7.1
radRBHEEvents	1.3.6.1.4.1.164.6.1.7.1.0			The events for RAD Stackable products.
radRBHT	1.3.6.1.4.1.164.6.1.7.2
radRBHTEvents	1.3.6.1.4.1.164.6.1.7.2.0			The events for RAD Stackable products.
radETS4fddiDAS	1.3.6.1.4.1.164.6.1.7.3
radETS4fddiSAS	1.3.6.1.4.1.164.6.1.7.4
radSAHEMX	1.3.6.1.4.1.164.6.1.7.5
radSAHTM	1.3.6.1.4.1.164.6.1.7.6
radETS4	1.3.6.1.4.1.164.6.1.7.7
radSAHEMU	1.3.6.1.4.1.164.6.1.7.8
unknown	1.3.6.1.4.1.164.6.1.7.9
radSAH16Eint	1.3.6.1.4.1.164.6.1.7.10
radSAH16Tint	1.3.6.1.4.1.164.6.1.7.11
radSAH16Eext	1.3.6.1.4.1.164.6.1.7.12
radSAH16Text	1.3.6.1.4.1.164.6.1.7.13
radSysPS	1.3.6.1.4.1.164.6.1.8
radSysPSEvents	1.3.6.1.4.1.164.6.1.8.0			The events for RAD Packet Switch (PS) products.
radSPS2	1.3.6.1.4.1.164.6.1.8.1
radSPS3	1.3.6.1.4.1.164.6.1.8.2
radSPS6	1.3.6.1.4.1.164.6.1.8.3
radSPS9	1.3.6.1.4.1.164.6.1.8.4
radSPS12	1.3.6.1.4.1.164.6.1.8.5
radAPD2	1.3.6.1.4.1.164.6.1.8.6
radAPD8	1.3.6.1.4.1.164.6.1.8.7
radAPS8	1.3.6.1.4.1.164.6.1.8.8
radAPS16	1.3.6.1.4.1.164.6.1.8.9
radAPS24	1.3.6.1.4.1.164.6.1.8.10
radSPS3S	1.3.6.1.4.1.164.6.1.8.11
radFPS8	1.3.6.1.4.1.164.6.1.8.12
radFPS12	1.3.6.1.4.1.164.6.1.8.13
radSPS3ScSL	1.3.6.1.4.1.164.6.1.8.14
radSPS3Sc2S	1.3.6.1.4.1.164.6.1.8.15
radFPS8c	1.3.6.1.4.1.164.6.1.8.16
radFPS4	1.3.6.1.4.1.164.6.1.8.17
radSPS4	1.3.6.1.4.1.164.6.1.8.18
radSysEth	1.3.6.1.4.1.164.6.1.9
radEP8T	1.3.6.1.4.1.164.6.1.9.1
radEP4TAUI	1.3.6.1.4.1.164.6.1.9.2
radEP4T2FL	1.3.6.1.4.1.164.6.1.9.3
radEP4TFL	1.3.6.1.4.1.164.6.1.9.4
radEP4FL	1.3.6.1.4.1.164.6.1.9.5
radEPR8T	1.3.6.1.4.1.164.6.1.9.7
radEPR4TAUI	1.3.6.1.4.1.164.6.1.9.8
radEPR4T2FL	1.3.6.1.4.1.164.6.1.9.9
radEPR4TFL	1.3.6.1.4.1.164.6.1.9.10
radEPR4FL	1.3.6.1.4.1.164.6.1.9.11
radSysRtr	1.3.6.1.4.1.164.6.1.11
radSysRtrEvents	1.3.6.1.4.1.164.6.1.11.0			The events for RAD Router products.
radRTED	1.3.6.1.4.1.164.6.1.11.1
radRTEM	1.3.6.1.4.1.164.6.1.11.2
radRTEC	1.3.6.1.4.1.164.6.1.11.3
radWebRanger	1.3.6.1.4.1.164.6.1.11.4
radTinyRouter	1.3.6.1.4.1.164.6.1.11.5
radLA240	1.3.6.1.4.1.164.6.1.11.6
radSuperLan	1.3.6.1.4.1.164.6.1.11.7
radLA240I	1.3.6.1.4.1.164.6.1.11.8
radFcdIsdn	1.3.6.1.4.1.164.6.1.11.9
radEFcdIp	1.3.6.1.4.1.164.6.1.11.10
radFcdIpD	1.3.6.1.4.1.164.6.1.11.11
radFcdIpM	1.3.6.1.4.1.164.6.1.11.12
radFcdIpL	1.3.6.1.4.1.164.6.1.11.13
radSysAtm	1.3.6.1.4.1.164.6.1.12
radSysAtmEvents	1.3.6.1.4.1.164.6.1.12.0			The events for RAD ATM products.
NTF atmAceSystemTrap	1.3.6.1.4.1.164.6.1.12.0.6			This trap alerts of major problems in the device.
NTF atmAceAlarmForwardingTrap	1.3.6.1.4.1.164.6.1.12.0.7			This trap is sent upon starting or stopping Alarm Forwarding Mechanism.
NTF atmAceDateAndTimeRequest	1.3.6.1.4.1.164.6.1.12.0.8			This trap is sent upon restart. Upon recieving this trap the NMS will set the device's date and time. This trap's purpose is to fix a problem in ACE2002, ACE-2002E, ACE-202. The problem is that the Date and Time is stored in the NVRAM, and when the NVRAM's battery is empty, the device loses this information.
NTF atmAceAlarmLOS	1.3.6.1.4.1.164.6.1.12.0.16			This trap indicates Loss Of Signal.
NTF atmAceAlarmLOF	1.3.6.1.4.1.164.6.1.12.0.17			This trap indicates Loss Of Frame.
NTF atmAceAlarmLCD	1.3.6.1.4.1.164.6.1.12.0.18			This trap indicates Loss of Cell Delineation.
NTF atmAceAlarmSLM	1.3.6.1.4.1.164.6.1.12.0.19			This trap indicates Signal Line Mismatch.
NTF atmAceAlarmLOP	1.3.6.1.4.1.164.6.1.12.0.20			This trap indicates Loss of Pointer.
NTF atmAceAlarmLineAIS	1.3.6.1.4.1.164.6.1.12.0.21			This trap indicates Line AIS.
NTF atmAceAlarmPathAIS	1.3.6.1.4.1.164.6.1.12.0.22			This trap indicates Path AIS.
NTF atmAceAlarmLineRDI	1.3.6.1.4.1.164.6.1.12.0.23			This trap indicates Line RDI.
NTF atmAceAlarmPathRDI	1.3.6.1.4.1.164.6.1.12.0.24			This trap indicates Path RDIand Path RAI(Yellow) for DS1 interfaces.
NTF atmAceAlarmSectionBIP	1.3.6.1.4.1.164.6.1.12.0.25			This trap indicates Section Bit Interleave Parity.
NTF atmAceAlarmLineBIP	1.3.6.1.4.1.164.6.1.12.0.26			This trap indicates Line Bit Interleave Parity.
NTF atmAceAlarmPathBIP	1.3.6.1.4.1.164.6.1.12.0.27			This trap indicates Path Bit Interleave Parity.
NTF atmAceAlarmLineFEBE	1.3.6.1.4.1.164.6.1.12.0.28			This trap indicates Line Far End Block Error.
NTF atmAceAlarmPathFEBE	1.3.6.1.4.1.164.6.1.12.0.29			This trap indicates Path Far End Block Error.
NTF atmAceAlarmPlcpLOF	1.3.6.1.4.1.164.6.1.12.0.30			This trap indicates T3 PLCP Loss Of Frame.
NTF atmAceAlarmPlcpYELLOW	1.3.6.1.4.1.164.6.1.12.0.31			This trap indicates T3 Plcp Yellow.
NTF atmAceAlarmPlcpBIP	1.3.6.1.4.1.164.6.1.12.0.32			This trap indicates T3 Plcp Bit Interleave Parity.
NTF atmAceAlarmPlcpFEBE	1.3.6.1.4.1.164.6.1.12.0.33			This trap indicates T3 Plcp Far End Block Error.
NTF atmAceAlarmPlcpP1P2	1.3.6.1.4.1.164.6.1.12.0.34			This trap indicates T3 Plcp Parity errors in P1/P2 bytes.
NTF atmAceAlarmUAS	1.3.6.1.4.1.164.6.1.12.0.35			This trap is sent upon UAS start or end per port.
NTF atmAceAlarmCluster	1.3.6.1.4.1.164.6.1.12.0.36			This trap is sent upon atmNteAlarmType start or end, for a cluster of VPs/VCs (according to atmNteLevel) with the same alarm on the same physical port. This trap replaces sending the same alarm for a big quantity (the quantity described in the product specification document) of VPs/VCs in order to prevent flooding the NMS and the network with traps.
NTF atmAceHwFailure	1.3.6.1.4.1.164.6.1.12.0.37			This trap is sent upon HW failure per port.
NTF atmAceUnavailableBwTrap	1.3.6.1.4.1.164.6.1.12.0.38			This trap is sent when Bandwidth allocation is > max possible value for the installed card. For ACE2002 this trap will be sent for the following cases: Card insertion - if the total Input and/or Output Bandwidth is over allocated, then the specific card rate will be set to 0 and this trap will be sent with the Input/Output rates values. Upgrade from former version - when an over allocated Bandwidth is detected, this trap will be sent with atmConfIfInputRate=atmConfIfOutputRate=0xFFFFFFFF.
NTF atmAceAlarmVpContinuityLoss	1.3.6.1.4.1.164.6.1.12.0.40			This trap indicates Loss of Continuity Check on a VP Connection.
NTF atmAceAlarmVpAISReception	1.3.6.1.4.1.164.6.1.12.0.41			This trap indicates AIS Reception on a VP Connection.
NTF atmAceAlarmVpRDIReception	1.3.6.1.4.1.164.6.1.12.0.42			This trap indicates RDI Reception on a VP Connection.
NTF atmAceAlarmVpErroredCells	1.3.6.1.4.1.164.6.1.12.0.43			This trap indicates Errored Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpLostCells	1.3.6.1.4.1.164.6.1.12.0.44			This trap indicates Lost Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpMisinsertedCells	1.3.6.1.4.1.164.6.1.12.0.45			This trap indicates Misinserted Cells on a VP Connection reported by PM.
NTF atmAceAlarmVpUAS	1.3.6.1.4.1.164.6.1.12.0.46			This trap is sent upon UAS start or end per VP.
NTF atmAceAlarmVpLoopback	1.3.6.1.4.1.164.6.1.12.0.47			This trap is sent upon OAM LoopBack fail status per VP.
NTF atmAceAlarmVpGCRAViolation	1.3.6.1.4.1.164.6.1.12.0.48			This trap indicates GCRA violation on a VP Connection reported by UPC device.
NTF atmAceAlarmVcContinuityLoss	1.3.6.1.4.1.164.6.1.12.0.56			This trap indicates Loss of Continuity Check on a VC Connection.
NTF atmAceAlarmVcAISReception	1.3.6.1.4.1.164.6.1.12.0.57			This trap indicates AIS Reception on a VC.
NTF atmAceAlarmVcRDIReception	1.3.6.1.4.1.164.6.1.12.0.58			This trap indicates RDI Reception on a VC Connection.
NTF atmAceAlarmVcErroredCells	1.3.6.1.4.1.164.6.1.12.0.59			This trap indicates Errored Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcLostCells	1.3.6.1.4.1.164.6.1.12.0.60			This trap indicates Lost Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcMisinsertedCells	1.3.6.1.4.1.164.6.1.12.0.61			This trap indicates Misinserted Cells on a VC Connection reported by PM.
NTF atmAceAlarmVcUnexpectedCell	1.3.6.1.4.1.164.6.1.12.0.62			This trap indicates an unexpected cell from user or network port.
NTF atmAceAlarmVcUAS	1.3.6.1.4.1.164.6.1.12.0.63			This trap is sent upon UAS start or end per VC.
NTF atmAceAlarmVcLoopback	1.3.6.1.4.1.164.6.1.12.0.64			This trap is sent upon OAM LoopBack fail status per VC.
NTF atmAceAlarmVcGCRAViolation	1.3.6.1.4.1.164.6.1.12.0.65			This trap indicates GCRA violation on a VC Connection reported by UPC device.
radStarSwitch	1.3.6.1.4.1.164.6.1.12.1
radStarSwitchATM25	1.3.6.1.4.1.164.6.1.12.1.1
radStarSwitchATM25L	1.3.6.1.4.1.164.6.1.12.1.2
radStarSwitchATM155	1.3.6.1.4.1.164.6.1.12.1.3
radAtmCsuDsu	1.3.6.1.4.1.164.6.1.12.2
radAmcdE1	1.3.6.1.4.1.164.6.1.12.2.1
radAmcdT1	1.3.6.1.4.1.164.6.1.12.2.2
radAce20E	1.3.6.1.4.1.164.6.1.12.2.3
radAce20T	1.3.6.1.4.1.164.6.1.12.2.4
radAce2005	1.3.6.1.4.1.164.6.1.12.2.5
radAce2002	1.3.6.1.4.1.164.6.1.12.2.6
radAce2002E	1.3.6.1.4.1.164.6.1.12.2.7
radAce2E	1.3.6.1.4.1.164.6.1.12.2.8
radAce2T	1.3.6.1.4.1.164.6.1.12.2.9
radMlAtmE1	1.3.6.1.4.1.164.6.1.12.2.10
radMlAtmT1	1.3.6.1.4.1.164.6.1.12.2.11
radAmc102	1.3.6.1.4.1.164.6.1.12.2.12
radAmc102c	1.3.6.1.4.1.164.6.1.12.2.13
radAce202	1.3.6.1.4.1.164.6.1.12.2.14
radAce	1.3.6.1.4.1.164.6.1.12.3
radAce101	1.3.6.1.4.1.164.6.1.12.3.1
radAce102	1.3.6.1.4.1.164.6.1.12.3.2
radAce50	1.3.6.1.4.1.164.6.1.12.3.3
radAce52	1.3.6.1.4.1.164.6.1.12.3.4
radAce52L	1.3.6.1.4.1.164.6.1.12.3.5
radAce201	1.3.6.1.4.1.164.6.1.12.3.7
radAce3200	1.3.6.1.4.1.164.6.1.12.3.8
radAce3100	1.3.6.1.4.1.164.6.1.12.3.9
radAce3400	1.3.6.1.4.1.164.6.1.12.3.10
radAce3402	1.3.6.1.4.1.164.6.1.12.3.11
radAce3100PSN	1.3.6.1.4.1.164.6.1.12.3.12
radAce3200PSN	1.3.6.1.4.1.164.6.1.12.3.13
radAce3400PSN	1.3.6.1.4.1.164.6.1.12.3.14
radAce3402PSN	1.3.6.1.4.1.164.6.1.12.3.15
radAce3600	1.3.6.1.4.1.164.6.1.12.3.16
radAce3205	1.3.6.1.4.1.164.6.1.12.3.17
radAce3105	1.3.6.1.4.1.164.6.1.12.3.18
radSysLA	1.3.6.1.4.1.164.6.1.13
radLA140	1.3.6.1.4.1.164.6.1.13.1
radLA110	1.3.6.1.4.1.164.6.1.13.2
radLA104	1.3.6.1.4.1.164.6.1.13.3
radLA130	1.3.6.1.4.1.164.6.1.13.4
radLA210	1.3.6.1.4.1.164.6.1.13.5
radSysTerminal	1.3.6.1.4.1.164.6.1.100
agnt	1.3.6.1.4.1.164.6.2
STR agnHwVersion	1.3.6.1.4.1.164.6.2.1	DisplayString	read-write	ASCII string for description and display of the agent hardware version, as it is known by the agent software.The user can update the version upon request when he changes components in the agent's module
I32 agnTrapMask	1.3.6.1.4.1.164.6.2.2	Integer32	read-write	The value of this attribute determines the type of traps the agent should mask and not send to the management console. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
OCT agnTrapValue	1.3.6.1.4.1.164.6.2.3	OCTET STRING	read-only	The value of the trap decoded in internal RAD format. Full description is given in the Trap definition file
C32 agnChangeCnt	1.3.6.1.4.1.164.6.2.4	Counter32	read-only	The number of changes in system configuration that were reported to the manager since last cold start
OID agnSpecific	1.3.6.1.4.1.164.6.2.5	OBJECT IDENTIFIER	read-only	Object identifier of entity containing additional information regarding this instance.
OCT agnConfigMsg	1.3.6.1.4.1.164.6.2.6	OCTET STRING	read-only	Full configuration message coded in internal RAD application format. This entry describes agent's configuration. For MP-2200 R3, this object describes agent's support of the V5.1 feature: 1 octet ; bit 0 (LSB). '1' - V5.1 feature is supported '0' - V5.1 feature is not supported.
mngTrapIpTable	1.3.6.1.4.1.164.6.2.7		not-accessible	This table indicates the destination address of the traps. Internally it will be limited to ten addresses.
mngEntry	1.3.6.1.4.1.164.6.2.7.1		not-accessible	An entry in table.
I32 mngID	1.3.6.1.4.1.164.6.2.7.1.1	Integer32	read-only	This value indicates an index of a specific IP address
IP mngIP	1.3.6.1.4.1.164.6.2.7.1.2	IpAddress	read-write	This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.
IP mngIPMask	1.3.6.1.4.1.164.6.2.7.1.3	IpAddress	read-write	This value indicates the mask of the destination addresses of the traps.
I32 mngTrapMask	1.3.6.1.4.1.164.6.2.7.1.4	Integer32	read-write	The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
OCT mngAlarmTrapMask	1.3.6.1.4.1.164.6.2.7.1.5	OCTET STRING	read-write	The value of this object determines the alarm traps that the agent should mask (not send to this manager). The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. For more details on the specific alarm traps masked, see product specification.
U32 mngSnmpTrapUdpPort	1.3.6.1.4.1.164.6.2.7.1.6	Unsigned32	read-write	This variable enables to set the UDP port (socket) used for SNMP traps.
INT agnIndication	1.3.6.1.4.1.164.6.2.8	INTEGER	read-only	Attribute describing the state of the entity the agent is responsible for. In case of a modular entity, the value of this attribute will be according to the component which is in the worst state. The order of severity (from top to bottom) is: critical-> major (or faulty)-> minor-> event-> warning-> normal (off).
INT agnMonitorModeCmd	1.3.6.1.4.1.164.6.2.9	INTEGER	read-write	Setting this attribute to ON, will enforce the agent to change its mode of operation to Monitor Mode
OCT agnLed	1.3.6.1.4.1.164.6.2.10	OCTET STRING	read-only	This entry specifies the LEDs status of the agent module . Each led will be represented by 4 bits where the first 2 bits (left) will specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY)
trapTable	1.3.6.1.4.1.164.6.2.11		not-accessible	This table may include the last few traps generated by the agent, for future retrieval. The table has a limited capacity. If traps are not retrieved in proper time, they will be over-written by new traps. For other devices, it can include generic variables that will be attached to traps as 'accessible-for-notify'.
trapEntry	1.3.6.1.4.1.164.6.2.11.1		not-accessible	An entry in trapTable.
I32 trapID	1.3.6.1.4.1.164.6.2.11.1.1	Integer32	read-only	This object indicates an index of a specific trap. Can be used also for any trap, while trapVal is used as 'accessible-for-notify' or trapNumeric is used.
STR trapVal	1.3.6.1.4.1.164.6.2.11.1.2	DisplayString	read-only	This object is the actual ASCII description of the trap. It can be used also as attached variable of traps, in order to detail in explicit ASCII text, data of the trap. In this case, it is used as 'accessible-for-notify'.
TIK trapTimeSinceOccurrence	1.3.6.1.4.1.164.6.2.11.1.3	TimeTicks	read-only	This object indicates the amount of time passed since the occurrence of the event that triggered this trap.
I32 trapNumeric	1.3.6.1.4.1.164.6.2.11.1.4	Integer32	accessible-for-notify	This object is a numeric general parameter, that can be attached to any trap. Values can be positive or negative.
fileTransfer	1.3.6.1.4.1.164.6.2.12
IP fileServerIP	1.3.6.1.4.1.164.6.2.12.1	IpAddress	read-write	The IP address of the server from which the file is loaded
STR fileName	1.3.6.1.4.1.164.6.2.12.2	DisplayString	read-write	The name of the file to be loaded. For protection, read returns NULL.
INT fileTransCmd	1.3.6.1.4.1.164.6.2.12.3	INTEGER	read-write	The command to be executed on fileName at fileServerIP.
I32 tftpRetryTimeOut	1.3.6.1.4.1.164.6.2.12.4	Integer32	read-write	General Retransmission time-out value (seconds)
I32 tftpTotalTimeOut	1.3.6.1.4.1.164.6.2.12.5	Integer32	read-write	Total Retransmission time-out value (seconds)
INT tftpStatus	1.3.6.1.4.1.164.6.2.12.6	INTEGER	read-write	Status of tftp session. When a session ended with success, the tftpStatus should be endedOk(6). Before restarting a tftp session, the NMS should set the tftpStatus to noOp(2). That's the reason of MAX-ACCESS read-write to this field.
OCT tftpError	1.3.6.1.4.1.164.6.2.12.7	OCTET STRING	read-only	The MSB represents the standard error code. The LSB represents the private error code. 0x0000 is No Error 0x0100 is File Not Found 0x0200 is Access violation 0x0300 is Disk full or allocation exceeded 0x0400 is Illegal TFTP operation 0x0500 is Unknown transfer ID 0x0600 is File already exists 0x0700 is No such user 0x0001 is Server Overflow 0x0002 is No empty UDP port 0x0003 is No empty connection 0x0004 is Illegal File Mode 0x0007 is Illegal PDU size 0x0008 is TFTP Server does not exist 0x0009 is Incorrect File 0x000A is Wrong License format 0x000B is License ID already used
OCT fileTransferToSubSystems	1.3.6.1.4.1.164.6.2.12.8	OCTET STRING	read-write	This object represents the sub-systems the fileTransCmd refers to. It should be used when a system is divided to sub-systems and each sub-system (or part of them) can have a different SW/Configuration. Each bit of this object will represent one of the sub-systems. Bit='1' - APPLY to respective sub-system Bit='0' - DO NOT APPLY to respective sub-system For the meaning of each bit, see product's specification. User will select the sub-systems envolved by filling-in the bits that represent these sub-systems. In this case, the file represented by 'fileName' will include several parts, each representing one of the sub-systems. The agent will refer only to the part/s indicated by this object. 0 Octet Strings = not applicable DEFVAL = 0h for the products that support this object.
STR fileNameWithinProduct	1.3.6.1.4.1.164.6.2.12.9	DisplayString	read-write	The file name used by the product within the product file system.
intSwdlTable	1.3.6.1.4.1.164.6.2.12.10		not-accessible	This parameters table is for internal Software down load. It also includes data about all files contained in the Object from which down-load is performed.
intSwdlEntry	1.3.6.1.4.1.164.6.2.12.10.1		not-accessible	An entry in table.
I32 intSwdlObjIdx	1.3.6.1.4.1.164.6.2.12.10.1.1	Integer32	read-only	The index of the object from which down-load is performed.
I32 intSwdlFileIdx	1.3.6.1.4.1.164.6.2.12.10.1.2	Integer32	read-only	The index of the files included in intSwdlObjIdx. One of these files can be selected to be internally downloaded.
STR intSwdlFileName	1.3.6.1.4.1.164.6.2.12.10.1.3	DisplayString	read-only	The name of the file.
STR intSwdlFileSwVer	1.3.6.1.4.1.164.6.2.12.10.1.4	DisplayString	read-only	The software version of the file.
STR intSwdlSwDate	1.3.6.1.4.1.164.6.2.12.10.1.5	DisplayString	read-only	The software version date of the file.
STR intSwdlSize	1.3.6.1.4.1.164.6.2.12.10.1.6	DisplayString	read-only	The size of the file.
INT intSwdlCmd	1.3.6.1.4.1.164.6.2.12.10.1.7	INTEGER	read-write	The command to down-load a SW file to an object. The Agent will change the value of this MIB object to off(2) automatically, after accepting the command.
OCT intSwdlToSubSystem	1.3.6.1.4.1.164.6.2.12.10.1.8	OCTET STRING	read-write	This object defines the subsystem for download. Bit='1'- APPLY to respective sub system. Bit='0'- DO NOT APPLY to respective sub system. For more details see product specification. For every octet bit0=LSB, bit7=MSB
INT intSwdlCardType	1.3.6.1.4.1.164.6.2.12.10.1.9	INTEGER	read-only	This object defines the Card type that this file is relevant for.
I32 intSwdlFlashIdx	1.3.6.1.4.1.164.6.2.12.10.1.10	Integer32	read-only	The index of the flash memory this file is stored in (1 or 2) (Example: 1= The file is stored in flash No.1). ASMi52 file will always be stored in Flash No.2 (intSwdlFlashIdx=2).
swdlStatusTable	1.3.6.1.4.1.164.6.2.12.11		not-accessible	This parameters table is for software download status. It also includes data about the files down-loaded or attempted to be down-loaded.
swdlStatusEntry	1.3.6.1.4.1.164.6.2.12.11.1		not-accessible	An entry in table.
I32 swdlStatusTypeIdx	1.3.6.1.4.1.164.6.2.12.11.1.1	Integer32	read-only	The index of the down-load type (e.g. external (1) or internal (2)).
I32 swdlStatusIdx	1.3.6.1.4.1.164.6.2.12.11.1.2	Integer32	read-only	The index of the status rows.
STR swdlStatusFileName	1.3.6.1.4.1.164.6.2.12.11.1.3	DisplayString	read-only	The name of the file.
STR swdlStatusSlot	1.3.6.1.4.1.164.6.2.12.11.1.4	DisplayString	read-only	The slot of the updated (or attempted to be updated) object.
STR swdlStatusSubSystem	1.3.6.1.4.1.164.6.2.12.11.1.5	DisplayString	read-only	The subsystem that updated (or attempted to be updated).
I32 swdlStatusStatus	1.3.6.1.4.1.164.6.2.12.11.1.6	Integer32	read-only	The status of the down load process. Value: Fail (2), OK (3), InProcess (4).
STR swdlStatusTime	1.3.6.1.4.1.164.6.2.12.11.1.7	DisplayString	read-only	This MIB parameter indicates the time SW download was finished. The format shuld be YYYY-MM-DD, hh:mm:ss
I32 clearDwldStatusLog	1.3.6.1.4.1.164.6.2.12.12	Integer32	read-write	This object clears the status log. Value: off(2), external(3), internal(4) The Agent will change the value of this MIB object to off(2) automatically, after accepting the command .
autoFileTransfer	1.3.6.1.4.1.164.6.2.12.13
autoFileTransferTable	1.3.6.1.4.1.164.6.2.12.13.1		not-accessible	Scheduling configuration table for Agent initiated file transfer.
autoFileTransferEntry	1.3.6.1.4.1.164.6.2.12.13.1.1		not-accessible	An entry in the table.
INT autoFileTransferType	1.3.6.1.4.1.164.6.2.12.13.1.1.1	INTEGER	read-only	This object defines the type of file to be transferred by agent.
IP autoFileTransferServerIp	1.3.6.1.4.1.164.6.2.12.13.1.1.2	IpAddress	read-write	This object defines the IP Address of the server to which the file is uploaded.
STR autoFileTransferFileName	1.3.6.1.4.1.164.6.2.12.13.1.1.3	SnmpAdminString	read-write	This object defines the name of the file to be uploaded.
INT autoFileTransferScheduling	1.3.6.1.4.1.164.6.2.12.13.1.1.4	INTEGER	read-write	This object defines schedule for TFTP Automatic session(s) initiated by Agent, according to the value selected: now - initiate immediate single session. recurrence- initiate single session 'every M time units'. or 'every N occurrences' or upon both, (earliest event). Time reccurence period (M) is defined by fileTransferTimeRecurrence. Occurrence reccurence (N) is defined by fileTransferOccurrenceRecurrence. Zero value means that the object is not relevant (not taken into account for the recurrence). It is invalid that both will have zero values in our case (recurrence). When both are non zero, file is transferred upon earliest event
I32 autoFileTransferTimeRecurrence	1.3.6.1.4.1.164.6.2.12.13.1.1.5	Integer32	read-write	This object defines time reccurence interval, e.g. M can be 'every M days', 'every M hours' etc. Zero is used to indicate there's no time reccurence (0= notApplicable). This object is taken into account only if autoFileTransferScheduling = recurrence For LA-110 time units are days.
I32 autoFileTransferOccurrenceRecurrence	1.3.6.1.4.1.164.6.2.12.13.1.1.6	Integer32	read-write	This object defines Occurrence reccurence interval, e.g N can be in 'every N alarms', 'every N log entries' etc. zero is used to indicate There's no Event Reccurence. (0= notApplicable) This object is taken into account only if autoFileTransferScheduling = recurrence Occurence Type (Alarms, etc.) is according to autoFileTransferType.
U32 fileTransferServerPort	1.3.6.1.4.1.164.6.2.12.14	Unsigned32	read-write	Server Port number used for File Transfer. Applicable for SFTP. Valid values: 0..65535.
INT fileTransferProtocol	1.3.6.1.4.1.164.6.2.12.15	INTEGER	read-write	File Transfer protocol used.
INT systemReset	1.3.6.1.4.1.164.6.2.13	INTEGER	read-write	Reset action to be performed on the system. - resetMapping - reset SDH/SONET mapping to default for all SDH/SONET links. - resetStandby(6) - can be used only by devices with redundancy on MAIN/CL.
systemTiming	1.3.6.1.4.1.164.6.2.14
STR systemDate	1.3.6.1.4.1.164.6.2.14.1	DisplayString	read-write	System date.
STR systemTime	1.3.6.1.4.1.164.6.2.14.2	DisplayString	read-write	System time.
I32 systemTimeElapsed	1.3.6.1.4.1.164.6.2.14.3	Integer32	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period. Same for all ports of the device.
systemNtp	1.3.6.1.4.1.164.6.2.14.4
INT systemNtpMode	1.3.6.1.4.1.164.6.2.14.4.1	INTEGER	read-write	This variable represents the NTP Mode.
I32 systemNtpGmt	1.3.6.1.4.1.164.6.2.14.4.2	Integer32	read-write	This variable represents the NTP GMT (Greenwich Mean Time), Possible values range is -12..12. For new devices/versions this variable will be in minutes.
IPt systemNtpServerAddressType	1.3.6.1.4.1.164.6.2.14.4.3	InetAddressType	read-write	This variable represents the NTP Server Address Type.
IP systemNtpServerAddress	1.3.6.1.4.1.164.6.2.14.4.4	InetAddress	read-write	This variable represents the NTP Server Address.
U32 systemNtpUpdateInterval	1.3.6.1.4.1.164.6.2.14.4.5	Unsigned32	read-write	This variable represents the NTP Update Interval, measured in seconds.
INT systemNtpCmd	1.3.6.1.4.1.164.6.2.14.4.6	INTEGER	read-write	This variable represents NTP possible commands. After the Agent accepts a command, it will automatically change the value to off(2).
schedXTable	1.3.6.1.4.1.164.6.2.14.5		not-accessible	An Augment to the Schedule table (schedTable in DISMAN-SCHEDULE-MIB; RFC-3231).
schedXEntry	1.3.6.1.4.1.164.6.2.14.5.1		not-accessible	An entry in the table.
U32 schedYear	1.3.6.1.4.1.164.6.2.14.5.1.1	Unsigned32	read-create	The year during which the scheduled action should take place.
INT schedWeekInMonth	1.3.6.1.4.1.164.6.2.14.5.1.2	INTEGER	read-create	The week in month (schedMonth) during which the scheduled action should take place.
I32 schedParam	1.3.6.1.4.1.164.6.2.14.5.1.3	Integer32	read-create	A Parameter that might be used whenever the scheduled action takes place. For summer-time schedule - This variable represents the time offset (in minutes), meaning: the number of minutes that should be added for summer-time.
systemPort	1.3.6.1.4.1.164.6.2.15
physicalConnectorTable	1.3.6.1.4.1.164.6.2.15.1		not-accessible	This table includes the connector type of ports or interfaces.
physicalConnectorEntry	1.3.6.1.4.1.164.6.2.15.1.1		not-accessible	An entry in table.
I32 portIdx	1.3.6.1.4.1.164.6.2.15.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
INT physicalConnector	1.3.6.1.4.1.164.6.2.15.1.1.2	INTEGER	read-only	The connector of the port/interface. other - none of the specified connectors none - no connector.
INT portOptWaveLength	1.3.6.1.4.1.164.6.2.15.1.1.3	INTEGER	read-only	Wave Length of an Optical interface/port in [nm] and specification if Laser or not. notApplicable - for non-optical ports.
INT portOptMode	1.3.6.1.4.1.164.6.2.15.1.1.4	INTEGER	read-only	Laser Mode of an Optical Laser interface/port. notApplicable - for non-Laser ports.
INT portBalance	1.3.6.1.4.1.164.6.2.15.1.1.5	INTEGER	read-write	This object is according to the port Impedance. For T1 - always balanced. For E1 - there are different impedance values for balanced and unbalanced.
INT portDdmSupport	1.3.6.1.4.1.164.6.2.15.1.1.6	INTEGER	read-only	SFP (Small Form Pluggable) port -support Digital Diagnostics Monitoring.
STR portMfgName	1.3.6.1.4.1.164.6.2.15.1.1.7	SnmpAdminString	read-only	(SFP) Port Manufacturer name (Maximum - 16 characters).
U32 portTypicalMaxRange	1.3.6.1.4.1.164.6.2.15.1.1.8	Unsigned32	read-only	Maximum range supported by SFP port, in meter units.
STR physicalConnectorString	1.3.6.1.4.1.164.6.2.15.1.1.9	SnmpAdminString	read-only	(SFP) connector type. It can be Vendor Specific (unknown in advance). Being a string, the object is not affected by any future new connectors. This object will usually not be used for drawing the connector.
STR portVendorPartNo	1.3.6.1.4.1.164.6.2.15.1.1.10	SnmpAdminString	read-only	SFP Vendor Part Number. Being a string, the object is not affected by any future new SFPs.
prtSupervisory	1.3.6.1.4.1.164.6.2.15.2
prtSpTable	1.3.6.1.4.1.164.6.2.15.2.1		not-accessible	A table.
prtSpEntry	1.3.6.1.4.1.164.6.2.15.2.1.1		not-accessible	Supervisory port parameter table.
I32 prtSupervisoryIndex	1.3.6.1.4.1.164.6.2.15.2.1.1.1	Integer32	read-only	The SP port index. For some products, having modules (cards): The LS byte of the integer is the port index 1..255. The MS byte is different than 0 only if the port belongs to a module. In that case it is the module number. For other products' index see their specification.
INT prtSupervisoryRate	1.3.6.1.4.1.164.6.2.15.2.1.1.2	INTEGER	read-write	This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
INT prtSupervisoryDataBits	1.3.6.1.4.1.164.6.2.15.2.1.1.3	INTEGER	read-write	This attribute indicates the number of data bits in an async frame
INT prtSupervisoryParity	1.3.6.1.4.1.164.6.2.15.2.1.1.4	INTEGER	read-write	This attribute indicates the parity mode in an async frame
INT prtSupervisoryStopBits	1.3.6.1.4.1.164.6.2.15.2.1.1.5	INTEGER	read-write	This attribute indicates the parity mode in an async frame.
INT prtSupervisoryUsage	1.3.6.1.4.1.164.6.2.15.2.1.1.6	INTEGER	read-write	This attribute indicates the usage of the SP port.
INT prtSupervisoryInterface	1.3.6.1.4.1.164.6.2.15.2.1.1.7	INTEGER	read-write	This attribute indicates the supervisory port interface.
INT prtSupervisoryCTS	1.3.6.1.4.1.164.6.2.15.2.1.1.8	INTEGER	read-write	CTS line state.
INT prtSupervisoryDcdDelay	1.3.6.1.4.1.164.6.2.15.2.1.1.9	INTEGER	read-write	DCD delay in msec.
INT prtSupervisoryDSR	1.3.6.1.4.1.164.6.2.15.2.1.1.10	INTEGER	read-write	DSR line state.
INT prtSupervisoryRoutProtocol	1.3.6.1.4.1.164.6.2.15.2.1.1.11	INTEGER	read-write	This attribute indicates the routing protocol of the port. notApplicable - for DP.
prtPerformance	1.3.6.1.4.1.164.6.2.15.3
prtPerfTable	1.3.6.1.4.1.164.6.2.15.3.1		not-accessible	This table includes G.826 ports or interfaces.
prtPerfEntry	1.3.6.1.4.1.164.6.2.15.3.1.1		not-accessible	An entry in table.
I32 prtPerfIdx	1.3.6.1.4.1.164.6.2.15.3.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
INT prtPerfPeriodRef	1.3.6.1.4.1.164.6.2.15.3.1.1.2	INTEGER	read-only	This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. lastPeriod - the period between last two commands of prtPerfSaveAndResetCmd. - If only one command occured since Start-up: the period between Start-up and last command. - If no command occured since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
I32 prtPerfElapsedTime	1.3.6.1.4.1.164.6.2.15.3.1.1.3	Integer32	read-only	Elapsed Time in seconds. - for prtPerfPeriodRef=currentPeriod: The period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. - for prtPerfPeriodRef=lastPeriod: The value of prtPerfElapsedTime when last prtPerfSaveAndResetCmd was received.
I32 prtPerfUAS	1.3.6.1.4.1.164.6.2.15.3.1.1.4	Integer32	read-only	Number of Unavailable Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfES	1.3.6.1.4.1.164.6.2.15.3.1.1.5	Integer32	read-only	Number of Errored Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfSES	1.3.6.1.4.1.164.6.2.15.3.1.1.6	Integer32	read-only	Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef).
I32 prtPerfBBE	1.3.6.1.4.1.164.6.2.15.3.1.1.7	Integer32	read-only	Number of Background Block (or Frame) Errors for the reference period (prtPerfPeriodRef).
I32 prtPerfBlocksPerSec	1.3.6.1.4.1.164.6.2.15.3.1.1.8	Integer32	read-only	Blocks per second (or frames per second) of the port/interface indicated by portIdx. This object is constant for a certain port/interface. It is not affected by the prtPerfPeriodRef index.
TIK prtPerfTimeTag	1.3.6.1.4.1.164.6.2.15.3.1.1.9	TimeTicks	read-only	Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was executed. This object is applicable only for prtPerfPeriodRef=lastPeriod. For prtPerfPeriodRef=currentPeriod, the value will always be 0.
INT prtPerfSaveAndResetCmd	1.3.6.1.4.1.164.6.2.15.3.1.1.10	INTEGER	read-write	A command per port/interface, to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. This object is applicable only for prtPerfPeriodRef=currentPeriod. Setting this object to on(3) for prtPerfPeriodRef=last, will cause the agent to return: Bad Value response. When setting validly this object to on(3), agent will perform the required command and will reset automatically the value of this object to off(2). Setting this object to off(2), will do nothing.
prtTest	1.3.6.1.4.1.164.6.2.15.4
prtTestTable	1.3.6.1.4.1.164.6.2.15.4.1		not-accessible	This table includes test data for ports or interfaces.
prtTestEntry	1.3.6.1.4.1.164.6.2.15.4.1.1		not-accessible	An entry in table.
I32 prtTestIdx	1.3.6.1.4.1.164.6.2.15.4.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
I32 prtTestCmdAndStatus	1.3.6.1.4.1.164.6.2.15.4.1.1.2	Integer32	read-write	Setting this object to a value as detailed further on (except 0) will initiate a test on the specific port. The test/s requested will be set according to the respective bit. The value of this object will be a sum of (2**n), where n is the Bit: TEST BIT VALUE ----------- --- ------ reserved 0 1 PayloadLoop=RLB 1 (=Remote Loopback) 2 LineLoop=DIG 2 (=Digital) 4 OtherLoop 3 8 InwardLoop=LLB 4 (=Local Loopback) 16 BERT 5 32 LC 6 64 ToneInjection 7 128 Inband 8 256 BERT Remote (or E1/T1 RLB) 9 512 Downstream-AIS (or E1/T1 LLB) 10 1024 Upstream-AIS 11 2048 Rem-Loop-on-Rem-Unit 12 4096 MacSwapLoop 13 8192 OamETHLoopback 14 16384 OamETHLinkTrace 15 32768 e.g : If the requested value is 20 -> 010100 -> Bits 2 & 4 are set -> the requested tests are : LineLoopback=DIG InwardLoopback=LLB Not all tests combinations are valid. For valid test combination, see each product's specification. For LRS52, only single test is allowed simultaneously The terminology and order of the first tests (except BERT) is according to the one used for Test Status of DS1 and DS3 standards. The notations : RLB, LLB, DIG are the most used in RAD's products, but they can be different. For exact definition see product's spec. Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port. When no test is running on the port, the Get value (test status) will be 0. PayloadLoop=RLB The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. LineLoop=DIG The received signal at this interface does not go through the device (minimum penetration) but is looped back out. OtherLoop Loopbacks that are not defined here. InwardLoop=LLB The sent signal at this interface is looped back through the device. LC This loop is applicable only for HSSI interface, towards the router . ToneInjection This loop is applicable for analog voice (like FXS). Downstream-AIS E1 AIS signal (all ones) is transmitted in the relevant channel toward the STM-1 line. Upstream-AIS E1 AIS signal (all ones) is generated in the relevant channel toward the local received tributary channel output Rem-Loop-on-Rem-Unit Request from far end device to activate remote loopback towards near-end device MacSwapLoop This loop is applicable for ethernet port. Loop is implemented by swapping the MAC addresses of the incoming message. OamETHLoopback Ethernet Loopback is used to verify connectivity of a MEP with a MIP or peer MEP(s) (ITU-T Y.1731, Clause 7.2). OamETHLinkTrace Ethernet Link Trace is an on-demand OAM function which can be used for the two following purposes: - Adjacent Relation Retrieval - Fault Localization (ITU-T Y.1731, Clause 7.3).
I32 prtBertCounter	1.3.6.1.4.1.164.6.2.15.4.1.1.3	Integer32	read-only	This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counter starts from zero (0) anytime BERT is initiated.
INT prtTestInitiator	1.3.6.1.4.1.164.6.2.15.4.1.1.4	INTEGER	read-only	This object indicates who initiated this port's test/s.
I32 prtTestTimeout	1.3.6.1.4.1.164.6.2.15.4.1.1.5	Integer32	read-write	This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. For RICi-E1T1, RICi-E3T3 the measurement unit is in seconds. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever
INT prtTestVctRxResult	1.3.6.1.4.1.164.6.2.15.4.1.1.6	INTEGER	read-only	This object indicates the result of the Vct on the cable connected to the RX connector.
INT prtTestVctTxResult	1.3.6.1.4.1.164.6.2.15.4.1.1.7	INTEGER	read-only	This object indicates the result of the Vct on the cable connected to the TX connector.
I32 prtTestVctRxDistance	1.3.6.1.4.1.164.6.2.15.4.1.1.8	Integer32	read-only	This object indicates the distance in Meters to the RX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
I32 prtTestVctTxDistance	1.3.6.1.4.1.164.6.2.15.4.1.1.9	Integer32	read-only	This object indicates the distance in Meters to the TX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
INT prtTestVctCmd	1.3.6.1.4.1.164.6.2.15.4.1.1.10	INTEGER	read-write	Vct command. on (3) = Start Vct on both cables connected to RX and TX connectors of this port. Agent will perform the required command and change automatically the value of this object to off(2).
I32 prtTestVctRxCrossPair	1.3.6.1.4.1.164.6.2.15.4.1.1.11	Integer32	read-only	This object should be equal to the Index (prtTestIdx) of the Rx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair. This object was especially created for ETX-202. Currently not in use.
I32 prtTestVctTxCrossPair	1.3.6.1.4.1.164.6.2.15.4.1.1.12	Integer32	read-only	This object should be equal to the Index (prtTestIdx) of the Tx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.
U32 prtTestActivationDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.13	Unsigned32	read-write	This object is applicable only when a single test is running. It indicates test activation delay in seconds. A Value of 0 indicates that the test starts immediately.
INT prtTestMacSwapLoopDataMode	1.3.6.1.4.1.164.6.2.15.4.1.1.14	INTEGER	read-write	This object defines which part of the data will be looped back.
I32 prtTestMacSwapLoopVlanId	1.3.6.1.4.1.164.6.2.15.4.1.1.15	Integer32	read-write	This object specifies the VLAN ID for prtTestMacSwapLoopDataMode=specificVlan.
INT prtTestMacSwapLoopDirection	1.3.6.1.4.1.164.6.2.15.4.1.1.16	INTEGER	read-write	This object defines the direction of the performed loopback. In ETX102 'local' corresponds to Ingress loop (either on User port or on Network port), and 'remote' corresponds to Egress loop (either on User port or on Network port).
MAC prtTestMacSwapLoopDestAddr	1.3.6.1.4.1.164.6.2.15.4.1.1.17	MacAddress	read-write	Configures the MAC address that will be sent in the Destination field of the packet in the outgoing direction.
MAC prtTestMacSwapLoopSrcAddr	1.3.6.1.4.1.164.6.2.15.4.1.1.18	MacAddress	read-write	Configures the MAC address that will be sent in the Source field of the packet in the outgoing direction.
U32 prtTestOamMinRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.19	Unsigned32	read-only	The mininal value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamMaxRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.20	Unsigned32	read-only	The maximum value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamAvgRoundTripDelay	1.3.6.1.4.1.164.6.2.15.4.1.1.21	Unsigned32	read-only	The average round trip delay of loopback message for a session of OAM loopback.Units are msec.
U32 prtTestOamTxInterval	1.3.6.1.4.1.164.6.2.15.4.1.1.22	Unsigned32	read-write	Indicates the interval between loopback sent messages.Units are msec.
IP prtTestDestinationIpAddress	1.3.6.1.4.1.164.6.2.15.4.1.1.23	IpAddress	read-write	Indicates the destination IP Address in the transmitted messages that are looped back.
U32 prtTestTTL	1.3.6.1.4.1.164.6.2.15.4.1.1.24	Unsigned32	read-write	Time-to-live.Number of hops the loopback message will go through the net before deciding to discard it.
U32 prtTestBwProfile	1.3.6.1.4.1.164.6.2.15.4.1.1.25	Unsigned32	read-write	Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test in order to limit the traffic that is looped back.
prtParam	1.3.6.1.4.1.164.6.2.15.5
prtParamTable	1.3.6.1.4.1.164.6.2.15.5.1		not-accessible	This table includes general port parameters. The meaning is different for every product that supports it due to a general parameter - prtControlCnfg. For ACE2002: -This table is used as a mechanism to create the next interface index. The algorithm description: The NMS will send the agent the following get command: get(nextIfIndex.index), where index=interface on which the new index is dependent on. Upon this command the agent will generate and return the new index to the NMS. - This table is partially supported according to the interface type. Upon getNext function the irrelevant parameters will be skipped.
prtParamEntry	1.3.6.1.4.1.164.6.2.15.5.1.1		not-accessible	An entry in table.
I32 prtParamIdx	1.3.6.1.4.1.164.6.2.15.5.1.1.1	Integer32	read-only	This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. For ACE2002: This parameter is the physical layer ifIndex of the slot on which the NMS requires the next interface index.
I32 prtControlCnfg	1.3.6.1.4.1.164.6.2.15.5.1.1.2	Integer32	read-write	This object may be used for port RW general parameter/s. For detailed meaning, see product's spec. Supported by: PRBi-E3/T3. For ACE2002: This parameter will include the value of the new index generated by agent. For Optimux-T3 and OP-155-1: This parameter will be used for Release Remote LLB Command: on=2= Set value only. Command to release LLB of Remote Unit. Agent will return automatically to 'off' value after performing the command. off=3=Get value only. For LA140 This parameter will be used as EchoCanceler per timeslot off = 2 Echo Canceler is disabled on = 3 Echo Canceler is enabled For FCD-155 This parameter will be used to select the port that is clock source for a PDH port, For E1/T1 PDH VC12/VT1.5 = 2 SDH/SONET = 3 For E3/T3 PDH VC3/DS3 = 2 SDH/SONET = 3 For ACE-52 This parameter will be used as Transmit Frame Type, i.e. which type of frame the corresponding bridge port will transmit: Untagged = 2 Tagged = 3 .
INT prtParamClkSrc	1.3.6.1.4.1.164.6.2.15.5.1.1.3	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' or 'loopback' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' or 'internal' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' or 'external' indicates that recovered receive clock from another card or interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'master' and 'fallback' values may be used RO to indicate active clock. 'station' - indicate clock received from station port is used as transmit clock.
INT prtParamPhantom	1.3.6.1.4.1.164.6.2.15.5.1.1.4	INTEGER	read-write	Power feeding to another device.
INT prtParamResetStatsCmd	1.3.6.1.4.1.164.6.2.15.5.1.1.5	INTEGER	read-write	Reset statistics of the selected port.
TIM prtParamLastResetStatsTime	1.3.6.1.4.1.164.6.2.15.5.1.1.6	TimeStamp	read-only	The value of MIB II's sysUpTime object at the last time that prtParamResetStatsCmd was Set to on(3) for this port. If prtParamResetStatsCmd was never Set to on(3) since last re-initialization of the agent, then this object contains a zero value. This object enables calculating the running time of Statistics counters for this port, by: [sysUpTime-prtParamLastResetStatsTime]. For some devices other types of 'Reset' may affect this parameter
INT prtParamInterfaceType	1.3.6.1.4.1.164.6.2.15.5.1.1.7	INTEGER	read-write	The type of the port.
INT prtParamClearAlarm	1.3.6.1.4.1.164.6.2.15.5.1.1.8	INTEGER	read-write	Setting this attribute to ON, will enforce a clear operation on the Port Alarms. Upon completion, the value will automatically change to off(2).
OCT prtParamLeds	1.3.6.1.4.1.164.6.2.15.5.1.1.9	OCTET STRING	read-only	This entry specifies the LEDs status of the port. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
INT prtParamLineLength	1.3.6.1.4.1.164.6.2.15.5.1.1.10	INTEGER	read-write	Line Length of the line connected to this port.
INT prtParamUsage	1.3.6.1.4.1.164.6.2.15.5.1.1.11	INTEGER	read-write	Defines whether this port works as User port or as Network port.
INT prtParamMappingMode	1.3.6.1.4.1.164.6.2.15.5.1.1.12	INTEGER	read-write	This object defines path protection on SONET/SDH link Auto - SONET/SDH mapping for port is copied automatically to same TU on the redundant SONET/SDH local (reside on same slot) link by agent. Manual - the user can configure the redundant mapping for port on the same link or to the other link on any TU Adjacent - similar to auto, but mapping is copied automatically by agent to link on adjacent slot .
INT prtParamAlarmIndication	1.3.6.1.4.1.164.6.2.15.5.1.1.13	INTEGER	read-only	This object indicates status-aggregation of non-masked alarms associated with all interface layers, related to this physical port. When at least one non-masked alarm exists on any layer, value of this object is on (3). Indication will be off (2) only when there's no active non-masked alarm on any interface layer related to this port. Masking an Alarm, will consider it as not exist for this indication. Example: When a port has an ATM higher layer and at least one VC has alarm, value of this object will be on (3)
OCT prtParamClkQualityLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.14	OCTET STRING	read-only	This parameter indicates quality level of clock signal. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows (when bit1=0): Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit)- Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization) 0001 PRS (=ST1 = Stratum 1 Traceable) 0111 ST2 (Stratum 2 Traceable) 1010 ST3 (Stratum 3 Traceable) 1100 SMC (SONET Minimum Clock Traceable) 1101 Stratum 3E Traceable bit1 = '1' - indicates all octet is Not Applicable
INT prtParamClkWaveShape	1.3.6.1.4.1.164.6.2.15.5.1.1.15	INTEGER	read-write	Wave shape of station clock source signal.
INT prtParamStatus	1.3.6.1.4.1.164.6.2.15.5.1.1.16	INTEGER	read-only	Station clock source Status.
I32 prtParamSignalLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.17	Integer32	read-only	This object indicates signal level (in thenth of dB units) on selected port.
OCT prtParamClkUserQualityLevel	1.3.6.1.4.1.164.6.2.15.5.1.1.18	OCTET STRING	read-write	This parameter allows user to mark quality level of clock. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows: Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit) Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization)
U32 prtParamDataRate	1.3.6.1.4.1.164.6.2.15.5.1.1.19	Unsigned32	read-write	Rate of serial data port (V.11, V.24, V.35) in kbps units.
INT prtParamLoopDetect	1.3.6.1.4.1.164.6.2.15.5.1.1.20	INTEGER	read-write	Enable/disable Loop Detection on a port. Examples of ports: physical, Channelized Bundle over TDM Uplink, Bridge Ports.
OCT prtParamActUponLoopDetect	1.3.6.1.4.1.164.6.2.15.5.1.1.21	OCTET STRING	read-write	This parameter is used to indicate which actions should be taken in case a loop is detected in the network the port is part of. Each action is represented by a bit. Currently defined (for RIC155GE/RIC622GE): Bit 0 - Transmit Shut Down Bit 1 - Forward Alarms If bit value = '1' then the action is taken. If bit value = '0' then the actions is not taken.
INT prtParamPSNLayer	1.3.6.1.4.1.164.6.2.15.5.1.1.22	INTEGER	read-write	This object indicates the network layer from which clock is derived.
INT prtParamRxSsm	1.3.6.1.4.1.164.6.2.15.5.1.1.23	INTEGER	read-write	This object indicates if Station Clock SSM messages received will serve as criteria for clock selection.
INT prtParamClkSsmRxSource	1.3.6.1.4.1.164.6.2.15.5.1.1.24	INTEGER	read-write	This object indicates the Sa-bit of the E1 frame, in which SSM messages are carried.
U32 prtParamFarEndDevice	1.3.6.1.4.1.164.6.2.15.5.1.1.26	Unsigned32	read-write	Programmed Far-End device connected to this port. This object is relevant for products having multiple DBs. It will enable configuring offline, the relevant data. For MP-4100, LRS-102 OP-108/106 cards, the options will be: 1 = None (when a port is not connected to any remote device) 2 = OP-108 3 = OP-108/ETH 4 = OP-106 5 = OP-106/ETH 6 = card of MP or LRS-102
INT prtParamTxClk	1.3.6.1.4.1.164.6.2.15.5.1.1.27	INTEGER	read-write	enable/disable station clock signal output.
prtIP	1.3.6.1.4.1.164.6.2.15.6
prtIpParamTable	1.3.6.1.4.1.164.6.2.15.6.1		not-accessible	A table - Parameters for IP Ports.
prtIpParamEntry	1.3.6.1.4.1.164.6.2.15.6.1.1		not-accessible	An entry in table.
I32 prtIpParamConfigIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.1	Integer32	read-only	This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). For products having Agent and Edit configurations, Write operation for the table entries is allowed only to Config=255.
I32 prtIpParamSlotIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.2	Integer32	read-only	This object indicates a unique number of the slot position in which the module is inserted. notApplicable = 255 (for products that don't have slots). For KM: kmxMlA (103), kmxMlB (104).
I32 prtIpParamIdx	1.3.6.1.4.1.164.6.2.15.6.1.1.3	Integer32	read-only	This object indicates a unique Port Index.
IP prtIpParamHostIP	1.3.6.1.4.1.164.6.2.15.6.1.1.4	IpAddress	read-write	The host interface IP address.
IP prtIpParamHostMask	1.3.6.1.4.1.164.6.2.15.6.1.1.5	IpAddress	read-write	The host interface subnet mask.
IP prtIpParamDefaultGateway	1.3.6.1.4.1.164.6.2.15.6.1.1.6	IpAddress	read-write	Default Gateway's IP Address.
INT prtIpParamMediaMode	1.3.6.1.4.1.164.6.2.15.6.1.1.7	INTEGER	read-only	This object indicates the real Media Mode.
INT prtIpParamMediaRate	1.3.6.1.4.1.164.6.2.15.6.1.1.8	INTEGER	read-only	This object indicates the real Media Rate (Mbps).
INT prtIpParamMngVlanSupport	1.3.6.1.4.1.164.6.2.15.6.1.1.9	INTEGER	read-write	Management VLAN support (Tagging). no - No support of VLAN Tagging. yes - 4 VLAN bytes will be added to the frame.
I32 prtIpParamMngVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.10	Integer32	read-write	Management VLAN ID.
I32 prtIpParamMngVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.11	Integer32	read-write	Management VLAN Frame priority.
INT prtIpParamRingMode	1.3.6.1.4.1.164.6.2.15.6.1.1.12	INTEGER	read-write	This object indicates If Ring Mode is enabled or not.
INT prtIpParamProtIpEnable	1.3.6.1.4.1.164.6.2.15.6.1.1.13	INTEGER	read-write	This object indicates whether a list of Protected IP Addresses is enabled or not. This object is applicable only if prtIpParamRingMode=enable.
INT prtIpParamTrafficPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.14	INTEGER	read-write	This object indicates the traffic priority of this port.
IP prtIpParamRemoteIP	1.3.6.1.4.1.164.6.2.15.6.1.1.15	IpAddress	read-write	This is the IP Address of the remote device that is connected to the current device (Point to Point Application). It is used for sending OAM packets on the LAN to the remote side in order to check that the connection is OK.
INT prtIpParamMaxTxBandwidth	1.3.6.1.4.1.164.6.2.15.6.1.1.16	INTEGER	read-write	This object shows the Max Bandwidth allowed on the LAN. Full - means that a Maximum of 100 Mega Byte Rate may go through the LAN. e1(3) means that the maximum is an E1 rate. t1(4) is for a maximum of a T1 rate.
I32 prtIpParamTos	1.3.6.1.4.1.164.6.2.15.6.1.1.17	Integer32	read-write	TOS = Type of Service transmitted. Valid values: 0..255.
INT prtIpParamConnect	1.3.6.1.4.1.164.6.2.15.6.1.1.18	INTEGER	read-write	Port Connection.
I32 prtIpParamAgingTime	1.3.6.1.4.1.164.6.2.15.6.1.1.19	Integer32	read-write	Aging Time in seconds.
INT prtIpParamEncapsulationProt	1.3.6.1.4.1.164.6.2.15.6.1.1.20	INTEGER	read-write	Encapsulation Protocol.
I32 prtIpParamEncapProtPort	1.3.6.1.4.1.164.6.2.15.6.1.1.21	Integer32	read-write	Encapsulation Protocol Port (TCP/UDP Port).
INT prtIpParamVlanSupport	1.3.6.1.4.1.164.6.2.15.6.1.1.22	INTEGER	read-write	VLAN support (Tagging). 'no' - No support of VLAN Tagging. 'yes' - 4 VLAN bytes will be added to the frame.
I32 prtIpParamVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.23	Integer32	read-write	VLAN Identifier.
I32 prtIpParamVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.24	Integer32	read-write	VLAN Frame priority.
I32 prtIpParamDoubleTagVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.25	Integer32	read-write	VLAN Identifier of the Double Tagging VLAN.
I32 prtIpParamDoubleTagVlanPriority	1.3.6.1.4.1.164.6.2.15.6.1.1.26	Integer32	read-write	VLAN Frame priority of the Double Tagging VLAN.
INT prtIpParamVlanTagging	1.3.6.1.4.1.164.6.2.15.6.1.1.27	INTEGER	read-write	VLAN Tagging. 'unmodified' - No change will be done to the Frame. 'tag' - Add Tag to Untagged Frames. 'doubleTag' - Add Tag to all Frames. 'doubleTagAndFallBack' - Double Tagging will have different rules for VLANs that this port is member in, than these it is not a member in. 'untag' - Remove Tag from tagged frames.
I32 prtIpParamRateLimit	1.3.6.1.4.1.164.6.2.15.6.1.1.28	Integer32	read-write	The maximum rate permitted to transfer via this port, in Kbps.
I32 prtIpParamDefInterface	1.3.6.1.4.1.164.6.2.15.6.1.1.29	Integer32	read-write	The Default Interface for packets with unresolved destination subnet. For internal-X port: 100 + X .
INT prtIpParamMng	1.3.6.1.4.1.164.6.2.15.6.1.1.30	INTEGER	read-write	This object indicates whether Management is enabled/disabled via this port.
I32 prtIpParamFloodedRateLimit	1.3.6.1.4.1.164.6.2.15.6.1.1.31	Integer32	read-write	The maximum rate permitted to transfer broadcast, multicast, and unicast flooded frames via this port, in Kbps. 0 - Disable. In Ipmux14 this parameter is applicable when prtIpParamRateLimit=0 (disable).
U32 prtIpParamBurstSize	1.3.6.1.4.1.164.6.2.15.6.1.1.32	Unsigned32	read-write	The burst size that the port can support beyond rate limitation determined in prtIpParamRateLimit. Burst Size is measured in bytes.
INT prtIpParamLimitPacketType	1.3.6.1.4.1.164.6.2.15.6.1.1.33	INTEGER	read-write	The packet type that will be rate limited. Rate limitation determined in prtIpParamRateLimit. all - All packet types are rate limited. broadMultiFloodedUnicast - Broadcast, Multicast and Flooded Unicast packets are rate limited. broadcastMulticast - Broadcast and Multicast packets are rate limited. broadcast - Broadcast packets are rate limited.
I32 prtIpParamKeepAliveInterval	1.3.6.1.4.1.164.6.2.15.6.1.1.34	Integer32	read-write	This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
I32 prtIpParamKeepAliveThresh	1.3.6.1.4.1.164.6.2.15.6.1.1.35	Integer32	read-write	This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
I32 prtIpParamP2pKeepAliveVlanId	1.3.6.1.4.1.164.6.2.15.6.1.1.36	Integer32	read-write	Dedicated VLAN ID for keep alive messages.
I32 prtIpParamP2pKeepAliveVlanPrio	1.3.6.1.4.1.164.6.2.15.6.1.1.37	Integer32	read-write	VLAN priority for P2P keep alive messages .
MAC prtIpParamRingAdjacentMacAddr	1.3.6.1.4.1.164.6.2.15.6.1.1.38	MacAddress	read-only	The MAC address of the adjacent NE connected to this port in an ETH ring. If the port is not a member of a ring, the value of this parameter will be 00-00-00-00-00-00.
prtClkSrc	1.3.6.1.4.1.164.6.2.15.7
prtClkSrcTable	1.3.6.1.4.1.164.6.2.15.7.1		not-accessible	A table - Parameters for master and fallback clock source of ports .
prtClkSrcEntry	1.3.6.1.4.1.164.6.2.15.7.1.1		not-accessible	An entry in table.
I32 prtClkSrcCnfgIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
I32 prtClkSrcPrtIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.2	Integer32	not-accessible	This object indicates a unique Port Index (receiving clock). Refer to device specification for port Index
INT prtClkSrcIdx	1.3.6.1.4.1.164.6.2.15.7.1.1.3	INTEGER	not-accessible	An index in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
INT prtClkSrcMode	1.3.6.1.4.1.164.6.2.15.7.1.1.4	INTEGER	read-write	This entry indicates the source the nodal timing is locked to.
I32 prtClkSrcPrt	1.3.6.1.4.1.164.6.2.15.7.1.1.5	Integer32	read-write	This entry is valid only when working in rxClk mode. It specifies the port from which the clock willl be taken. Refer to device specification for source port Index
opticalPort	1.3.6.1.4.1.164.6.2.15.8
optPrtMonitorTable	1.3.6.1.4.1.164.6.2.15.8.1		not-accessible	A table - optical port (e.g SFP) monitoring parameters, according to SFF-8472 Specification for Diagnostic Monitoring Interface for Optical Xcvrs. and ITU-T rec. G.958
optPrtMonitorEntry	1.3.6.1.4.1.164.6.2.15.8.1.1		not-accessible	An entry in table.
I32 optPrtMonitorPrtIdx	1.3.6.1.4.1.164.6.2.15.8.1.1.1	Integer32	not-accessible	This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
INT optPrtMonitorSample	1.3.6.1.4.1.164.6.2.15.8.1.1.2	INTEGER	not-accessible	This index indicates historic and current values - minimum, maximum and actual (current) value.
I32 optPrtMonitorTxPower	1.3.6.1.4.1.164.6.2.15.8.1.1.3	Integer32	read-only	Transmitted optical power level. Value is given in units of hundredth (1/100) of dBm.
I32 optPrtMonitorLaserBias	1.3.6.1.4.1.164.6.2.15.8.1.1.4	Integer32	read-only	LASER bias current level. Value is given in units of microAmper (uA).
I32 optPrtMonitorLaserTemp	1.3.6.1.4.1.164.6.2.15.8.1.1.5	Integer32	read-only	LASER temperature level, in hundredth (1/100) (C) degrees.
I32 optPrtMonitorRxPower	1.3.6.1.4.1.164.6.2.15.8.1.1.6	Integer32	read-only	Received optical power in units of hundredth (1/100) of dBm.
I32 optPrtMonitorSupplyVoltage	1.3.6.1.4.1.164.6.2.15.8.1.1.7	Integer32	read-only	Supply voltage, in hundredth (1/100) of volts (V).
optPrtCnfgTable	1.3.6.1.4.1.164.6.2.15.8.2		not-accessible	A table - optical port configuration
optPrtCnfgEntry	1.3.6.1.4.1.164.6.2.15.8.2.1		not-accessible	An entry in table.
U32 optPrtCnfgIdx	1.3.6.1.4.1.164.6.2.15.8.2.1.1	Unsigned32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.x.
U32 optPrtCnfgPrtIdx	1.3.6.1.4.1.164.6.2.15.8.2.1.2	Unsigned32	not-accessible	This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
INT optPrtCnfgALS	1.3.6.1.4.1.164.6.2.15.8.2.1.3	INTEGER	read-write	enable/disable Automatic Laser Shutdown
INT systemResetAllStatsCmd	1.3.6.1.4.1.164.6.2.16	INTEGER	read-write	Reset statistics of all ports and connections of the device.
INT systemClearTablesCmd	1.3.6.1.4.1.164.6.2.17	INTEGER	read-write	tempCnfgTables - Set RowStatus = destroy for all entries of some tables having RowStatus object, for temporary configuration only! (255). For the relevant tables, see product's specification. This object should be used by WAN product applications before performing the Update operation, in order to clear old entries of these tables. For MP-104/204 the entries will be destroyed for cnfg=1. off - agent will automatically change to this value, after performing the command.
I32 systemParameter	1.3.6.1.4.1.164.6.2.18	Integer32	read-write	This parameter can be used for different purposes: - TELNET session time-out in seconds. - Ace20: when trying to create row in a table that already has row with the same values, if set of values has to be unique in table, this attribute is set to the index of the existing row. - Optimux-T3: when CH interfaces are RJ-45, user can select via this object, the interface type for each Group of channels: T1 or E1: The selection will be a sum of the following Bits. '0' = T1 '1' = E1 Bit Group Value for each Bit having '1' 1 1 (CH-1..CH-8) 1 2 2 (CH-9..CH-12) 2 3 3 (CH-13..CH-20) 4 4 4 (CH-21..CH-28) 8 Examples: 15 = all Groups are selected to be E1 6 = Group 2 and Group 3 are selected to be E1 (Group 1 and Group 4 are T1). - FCD-A, FCD-M: user can select via this object the configuration used for Get values of MSDSL parameters that don't have configuration index. 1 =active configuration 255=temporary configuration. Set of this object should be done before Getting the MSDSL RW parameters. - Ace2002: This parameter indicates the number of intervals that were successfully uploaded upon statistics collection session. - FCD-IP, WR, FCD-IPD, LA-240: This parameter indicates whether Telnet Access is enabled/disabled: Values: 2 - Telnet Access is Disabled. 3 - Telnet Access is Enabled. -Vmux-110: This parameter value equals to maximum number of bundles. -Optimux-155: Simmilar usage to Optimux T3. user can select via this object, interface type T1 or E1 for each Group of channels (LIU): LIU group consists of 7 channels. Up to 12 LIUs are represented (84 T1 Channels). The selection will be a sum of the 2**n For each bit:'0' = T1 ,'1' = E1 Bit Group 1 1 (CH-1 .. CH-7) 2 2 (CH-8 .. CH-14) 3 3 (CH-15 ..CH-21) ... 9 9 (CH-56.. CH-63) ... 10 10 (CH-64..CH-70) 11 11 (CH-71..CH-77) 12 12 (CH-78..CH-84)
OCT agnGlobalAlarmMask	1.3.6.1.4.1.164.6.2.19	OCTET STRING	read-write	The value of this attribute determines the alarm traps the agent should mask and not send to the managers. Each bit from a certain octet represents a certain alarm.
INT alarmSeverity	1.3.6.1.4.1.164.6.2.20	INTEGER	read-only	This object specifies the severity of the alarms.
INT alarmState	1.3.6.1.4.1.164.6.2.21	INTEGER	read-only	.
INT agnTestStatus	1.3.6.1.4.1.164.6.2.22	INTEGER	read-only	Indicates the current test status (for all levels: system, card, port). This attribute will be set to: on(3): when there is at least one test in progress on the system/card/port off(2): when there is NO test in progress on the system/card/port
INT systemSaveAndResetAllStatsCmd	1.3.6.1.4.1.164.6.2.23	INTEGER	read-write	on - a command to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. off - agent will automatically change to this value, after performing the command.
IP systemDefaultGateway	1.3.6.1.4.1.164.6.2.24	IpAddress	read-write	Default Gateway's IP Address.
systemPsTable	1.3.6.1.4.1.164.6.2.25		not-accessible	This table describes the PS types of a device. Usage of this table is specified in the device's NMS SRS
systemPsEntry	1.3.6.1.4.1.164.6.2.25.1		not-accessible	An entry in table.
I32 systemPsIndex1	1.3.6.1.4.1.164.6.2.25.1.1	Integer32	read-only	First Index. In HUBs: 1 = PS-A slot 2 = PS-B slot 3 = PS-C slot. In SA units: 1 = PS1 2 = PS2 Default = 1
I32 systemPsIndex2	1.3.6.1.4.1.164.6.2.25.1.2	Integer32	read-only	Second Index. In HUBs: 1 always. In SA units: 1 = Local 2 = Remote Default = 1.
INT systemPsType	1.3.6.1.4.1.164.6.2.25.1.3	INTEGER	read-only	The type of PS, for a stand-alone product. acDc - PS that supports both AC and DC. acPF - Power Feeding (phantom) box that is feeding another box by external AC. dcPF - Power Feeding (phantom) box that is feeding another box by external DC.
INT systemPsStatus	1.3.6.1.4.1.164.6.2.25.1.4	INTEGER	read-only	The Status of the PS unit.
INT systemPsHotSwap	1.3.6.1.4.1.164.6.2.25.1.5	INTEGER	read-only	Is PS unit hot swap or fixed.
OCT agnFans	1.3.6.1.4.1.164.6.2.26	OCTET STRING	read-only	This entry specifies the FANs existence and status. Each fan will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each fan: 00 - FAN does not exist 01 - FAN exists and OK (Low Mode) 10 - High Mode (FAN OK) 11 - FAN exists and is Failed bits 0-1 are for first fan bits 2-3 are for 2nd fan (if exists) bits 4-5 are for 3nd fan (if exists) bits 6-7 are for 4nd fan (if exists) bits 8-9 are for 5nd fan (if exists) bits 10-11 are for 6nd fan (if exists) bits 12-13 are for 7nd fan (if exists) bits 14-15 are for 8nd fan (if exists).
I32 agnSendTrapParameter	1.3.6.1.4.1.164.6.2.27	Integer32	read-write	This object specifies if the agent will attach a specific parameter to a trap. For ACE2002 the agent will attach or not the openViewSeverity parameter according to the value of this parameter: 1 - will attach openViewSeverity. 0 - will not attach openViewSeverity.
OCT agnSensorsStatus	1.3.6.1.4.1.164.6.2.28	OCTET STRING	read-only	This entry specifies the Sensors (Temperature sensors or others) existence and status. Each sensor will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each sensor: 00 - sensor does not exist 01 - sensor exists and status is OK 11 - sensor exists and status is not OK ( e.g. temperature exceeds pre-defined threshold) bits 0-1 are for first sensor bits 2-3 are for 2nd sensor (if exists) and so on... Bit 0 is the LSB.
INT agnStationClockCard	1.3.6.1.4.1.164.6.2.29	INTEGER	read-only	This entry specifies the station clock card existence and status. notExist - station clock card (piggy) does not exist. notValid - station clock card exists but clock status is not valid. ok - station clock card exists, and its status is OK When the sepcific reason for clock status not being valid is known, it may be reported by lossOfSync or lossOfSignal values.
I32 xcIndexNext	1.3.6.1.4.1.164.6.2.30	Integer32	read-only	This object contains an appropriate value to be used for xcIndex when creating entries in the xcTable. The value 0 indicates that no unassigned entries are available. To obtain the xcIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
xcTable	1.3.6.1.4.1.164.6.2.31		not-accessible	Configuration of system cross-connect entries. The table follows the behavior described in RFC 2515, RFC 1604 regarding the creation deletion and modification of an entry within the table.
xcEntry	1.3.6.1.4.1.164.6.2.31.1		not-accessible	An entry in table.
I32 xcIndex	1.3.6.1.4.1.164.6.2.31.1.1	Integer32	not-accessible	Cross Connect Identifier.
I32 xcIfIndex1	1.3.6.1.4.1.164.6.2.31.1.2	Integer32	not-accessible	The interface Index from the ifTable, which identify one side of the connection.
I32 xcVpi	1.3.6.1.4.1.164.6.2.31.1.3	Integer32	not-accessible	The VPI value.
I32 xcVci	1.3.6.1.4.1.164.6.2.31.1.4	Integer32	not-accessible	The VCI value.
I32 xcIfIndex2	1.3.6.1.4.1.164.6.2.31.1.5	Integer32	not-accessible	The interface Index from the ifTable, which identifies the other side of the connection.
ROW xcRowStatus	1.3.6.1.4.1.164.6.2.31.1.6	RowStatus	read-create	This parameter allows NMS to create/delete entries of this table.
STR xcDescr	1.3.6.1.4.1.164.6.2.31.1.7	DisplayString	read-create	A textual string containing information about the xc entry.
INT xcAdminStatus	1.3.6.1.4.1.164.6.2.31.1.8	INTEGER	read-create	The desired administrative status of this bi-directional cross-connect.
INT xcOperStatus	1.3.6.1.4.1.164.6.2.31.1.9	INTEGER	read-only	The operational status of this bi-directional cross-connect.
INT xcAttachedIfType	1.3.6.1.4.1.164.6.2.31.1.10	INTEGER	read-only	This object indicates if the specific VCC is already attached to any interface, and indicates the type of the interface. This object's purpose is to ease the checking to the NMS. notApplicable - used for entries that are not LAN (as HDLC), or when the VCC was attached to a bridge, or when this parameter is irrelevant. free - the LAN VCC wasn't attached yet to any router interface. routerAtm - attached to an ATM router interface. lis - attached to a LIS interface.
I32 xcInputPriority	1.3.6.1.4.1.164.6.2.31.1.11	Integer32	read-create	This object is the priority, by which the LAN frames will be internaly sent to the ATM HW. This parameter is applicable if atmNteMdlInputPriorityMechanism=enabled. 1 - Highest priority. Will be the first to be sent to the ATM HW. 4 - Lowest priority. Will be the last to be sent to the ATM HW.
I32 xcBitMapping	1.3.6.1.4.1.164.6.2.31.1.12	Integer32	read-only	This object maps this entry to a bit of an octet string. For ACE2002 this object maps the LAN VCC to the bit of the VLAN Port Lists. If the value is '0' then it means that this VCC is not mapped to a port list or it may be an HDSL entry.
systemModule	1.3.6.1.4.1.164.6.2.32
modlParam	1.3.6.1.4.1.164.6.2.32.1
modlParamTable	1.3.6.1.4.1.164.6.2.32.1.1		not-accessible	This table include parameters for system modules.
modlParamEntry	1.3.6.1.4.1.164.6.2.32.1.1.1		not-accessible	An entry in table.
I32 modlParamIndex	1.3.6.1.4.1.164.6.2.32.1.1.1.1	Integer32	read-only	The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4.
INT modlParamReset	1.3.6.1.4.1.164.6.2.32.1.1.1.2	INTEGER	read-write	Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2).
INT modlParamSwdlStatus	1.3.6.1.4.1.164.6.2.32.1.1.1.3	INTEGER	read-only	This parameter indicates whatever the swdl is in process or not.
OCT modlParamLeds	1.3.6.1.4.1.164.6.2.32.1.1.1.4	OCTET STRING	read-only	This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
INT modlParamType	1.3.6.1.4.1.164.6.2.32.1.1.1.5	INTEGER	read-only	This attribute indicates the Module Type.
STR modlParamSwVer	1.3.6.1.4.1.164.6.2.32.1.1.1.6	DisplayString	read-only	This attribute indicates the Module's Software Version.
INT agnNearFarConnection	1.3.6.1.4.1.164.6.2.33	INTEGER	read-only	This parameter describes the connection between near-end and far-end agents.
agnAccess	1.3.6.1.4.1.164.6.2.34
INT agnTelnetAccess	1.3.6.1.4.1.164.6.2.34.1	INTEGER	read-write	Enable/Disable accessing the device via Telnet. disable - no one will be allowed to access the device via Telnet. enable - all users are allowed Telnet Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSH) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSH).
INT agnWebAccess	1.3.6.1.4.1.164.6.2.34.2	INTEGER	read-write	Enable/Disable accessing the device via Web. disable - no one will be allowed to access the device via Web. enable - all users are allowed Web Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSL) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSL).
INT agnRadiusAccess	1.3.6.1.4.1.164.6.2.34.3	INTEGER	read-write	Enable/Disable authentication via RADIUS server.
INT agnSshAccess	1.3.6.1.4.1.164.6.2.34.4	INTEGER	read-write	Enable/Disable accessing the device via SSH. disable - no one will be allowed to access the device via SSH. enable - all users are allowed SSH Access. managersOnly - Only manager stations listed in the manager's list are allowed.
systemInterface	1.3.6.1.4.1.164.6.2.35
ifCreateTable	1.3.6.1.4.1.164.6.2.35.1		not-accessible	The Interface Configuration Table. This table enables to create interfaces of Entities.
ifCreateEntry	1.3.6.1.4.1.164.6.2.35.1.1		not-accessible	An entry in the Interface Configuration table.
SYS ifCreateEntityType	1.3.6.1.4.1.164.6.2.35.1.1.1	SysIfEntityType	read-only	This object indicates the Type of the Entity that exists above the created interface. For a Logical Port, this value can be: other (1) when there is no fixed entity above it.
I32 ifCreateEntityIdx	1.3.6.1.4.1.164.6.2.35.1.1.2	Integer32	read-only	This object indicates the Index of the Entity that exists above the created interface. For a Logical Port, this value can be: 9999 - N/A when there is no fixed entity above it.
I32 ifCreateNumber	1.3.6.1.4.1.164.6.2.35.1.1.3	Integer32	read-only	This object indicates the number of the Interface that is created.
ROW ifCreateRowStatus	1.3.6.1.4.1.164.6.2.35.1.1.4	RowStatus	read-create	This object enables the user to create/delete entries in this table.
IAN ifCreateType	1.3.6.1.4.1.164.6.2.35.1.1.5	IANAifType	read-create	This object indicates the Type of the Interface that is created.
I32 ifCreateIndex	1.3.6.1.4.1.164.6.2.35.1.1.6	Integer32	read-only	This object indicates the ifIndex of the created Interface. The ifIndex is assigned by the device.
I32 ifCreateConnectedTo	1.3.6.1.4.1.164.6.2.35.1.1.7	Integer32	read-create	This object indicates the entity connected to the created Interface. The value of this object can be ifIndex of the connected entity or any other number that can identify it.
U32 ifCreateParams	1.3.6.1.4.1.164.6.2.35.1.1.8	Unsigned32	read-create	This object represents one or more parameters of the created Interface. Each group of bits (one or more bits) represents a specific parameter and its possible values. This object's mapping and interpretation will be specified in each device's specification documents. The parameter should be used within the create PDU assuming atomic operation.
NUM ifCreateConnectionPointer	1.3.6.1.4.1.164.6.2.35.1.1.9	RowPointer	read-create	This parameter represents the entity that is connected to this Interface. It can be used instead of ifCreateConnectedTo. It is an OBJECT IDENTIFIER. This parameter's SYNTAX allows the following possibilities: - can be simply used for entity that is not an interface - is not limited to include up to 32 bits The value of this parameter is a pointer to an existing row of a table, where the entity connected to this Interface is defined (i.e. the pointer uniquely identifies the connected entity). Examples: In case of an interface (from 2863.ifTable): points to 'ifEntry' of corresponding row = . In case of a VPI/VCI (from 2515.atmVclTable): points to 'atmVclEntry' of corresponding row = ..VPI.VCI In case no entity is connected, value = 0 .
interfacePerformance	1.3.6.1.4.1.164.6.2.35.2
ifPerfTable	1.3.6.1.4.1.164.6.2.35.2.1		not-accessible	Interface Performance Table. The propose of this table is to support statistics counters having 64 bit by using 2 parameters with syntax= Integer32. This is because SNMPv1 does not support Counter64 properly. For SNMPv3, ifPerfHCCounter (Counter64) may be supported.
ifPerfEntry	1.3.6.1.4.1.164.6.2.35.2.1.1		not-accessible	An entry in the Interface Performance Table.
I32 ifPerfCounterType	1.3.6.1.4.1.164.6.2.35.2.1.1.1	Integer32	not-accessible	2nd index of the ifPerfTable. This parameter represents the Counter Type. Each application can have a different association between this object's value and counter type - see relevant application spec. For VPLS-MTU application use the following values: 1= Rx Octets, 2= Tx Octets, 3= Rx Frames, 4= Tx Frames, 5=Rx Dropped Frames, 6= Tx Dropped Frames. Optionally, counter type description appears in agnListDecodingTable
U32 ifPerfLowCounterPart	1.3.6.1.4.1.164.6.2.35.2.1.1.2	Unsigned32	read-only	In order to support Counters having 64 bit length, the performance counter is divided into two 32 bit parameters as follows: [ 64 bit parameter ] = [ High 32 bit parameter ][ Low 32 bit parameter ]. This parameter holds the Low 32 bits of the counter, while the following parameter holds the High 32 bits of the counter.
U32 ifPerfHighCounterPart	1.3.6.1.4.1.164.6.2.35.2.1.1.3	Unsigned32	read-only	This parameter holds the High 32 bits of the counter (see description in the above parameter).
C64 ifPerfHCCounter	1.3.6.1.4.1.164.6.2.35.2.1.1.4	Counter64	read-only	This High Capacity counter holds whole 64 bits of the counter indicated by ifPerfCounterType (concatenates both counter parts ifPerfHighCounterPart&ifPerfLowCounterPart) This object can be supported only by agents using SNMPv2 or SNMPv3.
systemOam	1.3.6.1.4.1.164.6.2.36
systemOamTable	1.3.6.1.4.1.164.6.2.36.1		not-accessible	The OAM Configuration Table.
systemOamEntry	1.3.6.1.4.1.164.6.2.36.1.1		not-accessible	An entry in the OAM table.
I32 systemOamCnfgIdx	1.3.6.1.4.1.164.6.2.36.1.1.1	Integer32	not-accessible	This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
I32 systemOamFrequency	1.3.6.1.4.1.164.6.2.36.1.1.2	Integer32	read-write	Time in sec. between 2 OAM packets.
I32 systemOamTimeoutCycles	1.3.6.1.4.1.164.6.2.36.1.1.3	Integer32	read-write	No. of cycles the agent will send OAM packets without receiving a response from the remote device before declaring that the connection to the remote side is down - Time Out.
INT systemOamLinkCheck	1.3.6.1.4.1.164.6.2.36.1.1.4	INTEGER	read-write	This MIB object determines whether continuous connectivity Link checks will be performed by the device for uplinks. For Vmux-2100: enable (3) value can be set upon device installation. In this case, TDM Link Connectivity checks can be performed even before the user configures the Links of the device.If the value is enable (3) and there is no connection with the remote side, the Test LED will blink on the Main Board Module.
systemOamDescrTable	1.3.6.1.4.1.164.6.2.36.2		not-accessible	The OAM Descriptors Configuration Table.

radMiricE3T3

1.3.6.1.4.1.164.6.1.5.50

radEthAccess

1.3.6.1.4.1.164.6.1.6

radETX510

1.3.6.1.4.1.164.6.1.6.1

radEGate100

1.3.6.1.4.1.164.6.1.6.2

radEGate20

1.3.6.1.4.1.164.6.1.6.3

radRici8E1

1.3.6.1.4.1.164.6.1.6.4

radRici8T1

1.3.6.1.4.1.164.6.1.6.5

radRici4E1

1.3.6.1.4.1.164.6.1.6.6

radRici4T1

1.3.6.1.4.1.164.6.1.6.7

radETX550

1.3.6.1.4.1.164.6.1.6.9

radRici16

1.3.6.1.4.1.164.6.1.6.10

radETX102A

1.3.6.1.4.1.164.6.1.6.11

radETX202A

1.3.6.1.4.1.164.6.1.6.12

radETX201A

1.3.6.1.4.1.164.6.1.6.13

radETX201

1.3.6.1.4.1.164.6.1.6.14

radUNT20Ric

1.3.6.1.4.1.164.6.1.6.15

radRici4E1L

1.3.6.1.4.1.164.6.1.6.16

radRici8E1L

1.3.6.1.4.1.164.6.1.6.17

radRici155GE

1.3.6.1.4.1.164.6.1.6.18

radRici622GE

1.3.6.1.4.1.164.6.1.6.19

radETX208

1.3.6.1.4.1.164.6.1.6.20

radETX202AW

1.3.6.1.4.1.164.6.1.6.21

radETX102H

1.3.6.1.4.1.164.6.1.6.22

radETX202H

1.3.6.1.4.1.164.6.1.6.23

radSysStkHub

1.3.6.1.4.1.164.6.1.7

radRBHE

1.3.6.1.4.1.164.6.1.7.1

radRBHEEvents

1.3.6.1.4.1.164.6.1.7.1.0

The events for RAD Stackable products.

radRBHT

1.3.6.1.4.1.164.6.1.7.2

radRBHTEvents

1.3.6.1.4.1.164.6.1.7.2.0

The events for RAD Stackable products.

radETS4fddiDAS

1.3.6.1.4.1.164.6.1.7.3

radETS4fddiSAS

1.3.6.1.4.1.164.6.1.7.4

radSAHEMX

1.3.6.1.4.1.164.6.1.7.5

radSAHTM

1.3.6.1.4.1.164.6.1.7.6

radETS4

1.3.6.1.4.1.164.6.1.7.7

radSAHEMU

1.3.6.1.4.1.164.6.1.7.8

unknown

1.3.6.1.4.1.164.6.1.7.9

radSAH16Eint

1.3.6.1.4.1.164.6.1.7.10

radSAH16Tint

1.3.6.1.4.1.164.6.1.7.11

radSAH16Eext

1.3.6.1.4.1.164.6.1.7.12

radSAH16Text

1.3.6.1.4.1.164.6.1.7.13

radSysPS

1.3.6.1.4.1.164.6.1.8

radSysPSEvents

1.3.6.1.4.1.164.6.1.8.0

The events for RAD Packet Switch (PS) products.

radSPS2

1.3.6.1.4.1.164.6.1.8.1

radSPS3

1.3.6.1.4.1.164.6.1.8.2

radSPS6

1.3.6.1.4.1.164.6.1.8.3

radSPS9

1.3.6.1.4.1.164.6.1.8.4

radSPS12

1.3.6.1.4.1.164.6.1.8.5

radAPD2

1.3.6.1.4.1.164.6.1.8.6

radAPD8

1.3.6.1.4.1.164.6.1.8.7

radAPS8

1.3.6.1.4.1.164.6.1.8.8

radAPS16

1.3.6.1.4.1.164.6.1.8.9

radAPS24

1.3.6.1.4.1.164.6.1.8.10

radSPS3S

1.3.6.1.4.1.164.6.1.8.11

radFPS8

1.3.6.1.4.1.164.6.1.8.12

radFPS12

1.3.6.1.4.1.164.6.1.8.13

radSPS3ScSL

1.3.6.1.4.1.164.6.1.8.14

radSPS3Sc2S

1.3.6.1.4.1.164.6.1.8.15

radFPS8c

1.3.6.1.4.1.164.6.1.8.16

radFPS4

1.3.6.1.4.1.164.6.1.8.17

radSPS4

1.3.6.1.4.1.164.6.1.8.18

radSysEth

1.3.6.1.4.1.164.6.1.9

radEP8T

1.3.6.1.4.1.164.6.1.9.1

radEP4TAUI

1.3.6.1.4.1.164.6.1.9.2

radEP4T2FL

1.3.6.1.4.1.164.6.1.9.3

radEP4TFL

1.3.6.1.4.1.164.6.1.9.4

radEP4FL

1.3.6.1.4.1.164.6.1.9.5

radEPR8T

1.3.6.1.4.1.164.6.1.9.7

radEPR4TAUI

1.3.6.1.4.1.164.6.1.9.8

radEPR4T2FL

1.3.6.1.4.1.164.6.1.9.9

radEPR4TFL

1.3.6.1.4.1.164.6.1.9.10

radEPR4FL

1.3.6.1.4.1.164.6.1.9.11

radSysRtr

1.3.6.1.4.1.164.6.1.11

radSysRtrEvents

1.3.6.1.4.1.164.6.1.11.0

The events for RAD Router products.

radRTED

1.3.6.1.4.1.164.6.1.11.1

radRTEM

1.3.6.1.4.1.164.6.1.11.2

radRTEC

1.3.6.1.4.1.164.6.1.11.3

radWebRanger

1.3.6.1.4.1.164.6.1.11.4

radTinyRouter

1.3.6.1.4.1.164.6.1.11.5

radLA240

1.3.6.1.4.1.164.6.1.11.6

radSuperLan

1.3.6.1.4.1.164.6.1.11.7

radLA240I

1.3.6.1.4.1.164.6.1.11.8

radFcdIsdn

1.3.6.1.4.1.164.6.1.11.9

radEFcdIp

1.3.6.1.4.1.164.6.1.11.10

radFcdIpD

1.3.6.1.4.1.164.6.1.11.11

radFcdIpM

1.3.6.1.4.1.164.6.1.11.12

radFcdIpL

1.3.6.1.4.1.164.6.1.11.13

radSysAtm

1.3.6.1.4.1.164.6.1.12

radSysAtmEvents

1.3.6.1.4.1.164.6.1.12.0

The events for RAD ATM products.

NTF atmAceSystemTrap

1.3.6.1.4.1.164.6.1.12.0.6

This trap alerts of major problems in the device.

NTF atmAceAlarmForwardingTrap

1.3.6.1.4.1.164.6.1.12.0.7

This trap is sent upon starting or stopping Alarm Forwarding Mechanism.

NTF atmAceDateAndTimeRequest

1.3.6.1.4.1.164.6.1.12.0.8

This trap is sent upon restart. Upon recieving this trap the NMS will set the device's date and time. This trap's purpose is to fix a problem in ACE2002, ACE-2002E, ACE-202. The problem is that the Date and Time is stored in the NVRAM, and when the NVRAM's battery is empty, the device loses this information.

NTF atmAceAlarmLOS

1.3.6.1.4.1.164.6.1.12.0.16

This trap indicates Loss Of Signal.

NTF atmAceAlarmLOF

1.3.6.1.4.1.164.6.1.12.0.17

This trap indicates Loss Of Frame.

NTF atmAceAlarmLCD

1.3.6.1.4.1.164.6.1.12.0.18

This trap indicates Loss of Cell Delineation.

NTF atmAceAlarmSLM

1.3.6.1.4.1.164.6.1.12.0.19

This trap indicates Signal Line Mismatch.

NTF atmAceAlarmLOP

1.3.6.1.4.1.164.6.1.12.0.20

This trap indicates Loss of Pointer.

NTF atmAceAlarmLineAIS

1.3.6.1.4.1.164.6.1.12.0.21

This trap indicates Line AIS.

NTF atmAceAlarmPathAIS

1.3.6.1.4.1.164.6.1.12.0.22

This trap indicates Path AIS.

NTF atmAceAlarmLineRDI

1.3.6.1.4.1.164.6.1.12.0.23

This trap indicates Line RDI.

NTF atmAceAlarmPathRDI

1.3.6.1.4.1.164.6.1.12.0.24

This trap indicates Path RDIand Path RAI(Yellow) for DS1 interfaces.

NTF atmAceAlarmSectionBIP

1.3.6.1.4.1.164.6.1.12.0.25

This trap indicates Section Bit Interleave Parity.

NTF atmAceAlarmLineBIP

1.3.6.1.4.1.164.6.1.12.0.26

This trap indicates Line Bit Interleave Parity.

NTF atmAceAlarmPathBIP

1.3.6.1.4.1.164.6.1.12.0.27

This trap indicates Path Bit Interleave Parity.

NTF atmAceAlarmLineFEBE

1.3.6.1.4.1.164.6.1.12.0.28

This trap indicates Line Far End Block Error.

NTF atmAceAlarmPathFEBE

1.3.6.1.4.1.164.6.1.12.0.29

This trap indicates Path Far End Block Error.

NTF atmAceAlarmPlcpLOF

1.3.6.1.4.1.164.6.1.12.0.30

This trap indicates T3 PLCP Loss Of Frame.

NTF atmAceAlarmPlcpYELLOW

1.3.6.1.4.1.164.6.1.12.0.31

This trap indicates T3 Plcp Yellow.

NTF atmAceAlarmPlcpBIP

1.3.6.1.4.1.164.6.1.12.0.32

This trap indicates T3 Plcp Bit Interleave Parity.

NTF atmAceAlarmPlcpFEBE

1.3.6.1.4.1.164.6.1.12.0.33

This trap indicates T3 Plcp Far End Block Error.

NTF atmAceAlarmPlcpP1P2

1.3.6.1.4.1.164.6.1.12.0.34

This trap indicates T3 Plcp Parity errors in P1/P2 bytes.

NTF atmAceAlarmUAS

1.3.6.1.4.1.164.6.1.12.0.35

This trap is sent upon UAS start or end per port.

NTF atmAceAlarmCluster

1.3.6.1.4.1.164.6.1.12.0.36

This trap is sent upon atmNteAlarmType start or end, for a cluster of VPs/VCs (according to atmNteLevel) with the same alarm on the same physical port. This trap replaces sending the same alarm for a big quantity (the quantity described in the product specification document) of VPs/VCs in order to prevent flooding the NMS and the network with traps.

NTF atmAceHwFailure

1.3.6.1.4.1.164.6.1.12.0.37

This trap is sent upon HW failure per port.

NTF atmAceUnavailableBwTrap

1.3.6.1.4.1.164.6.1.12.0.38

This trap is sent when Bandwidth allocation is > max possible value for the installed card. For ACE2002 this trap will be sent for the following cases: Card insertion - if the total Input and/or Output Bandwidth is over allocated, then the specific card rate will be set to 0 and this trap will be sent with the Input/Output rates values. Upgrade from former version - when an over allocated Bandwidth is detected, this trap will be sent with atmConfIfInputRate=atmConfIfOutputRate=0xFFFFFFFF.

NTF atmAceAlarmVpContinuityLoss

1.3.6.1.4.1.164.6.1.12.0.40

This trap indicates Loss of Continuity Check on a VP Connection.

NTF atmAceAlarmVpAISReception

1.3.6.1.4.1.164.6.1.12.0.41

This trap indicates AIS Reception on a VP Connection.

NTF atmAceAlarmVpRDIReception

1.3.6.1.4.1.164.6.1.12.0.42

This trap indicates RDI Reception on a VP Connection.

NTF atmAceAlarmVpErroredCells

1.3.6.1.4.1.164.6.1.12.0.43

This trap indicates Errored Cells on a VP Connection reported by PM.

NTF atmAceAlarmVpLostCells

1.3.6.1.4.1.164.6.1.12.0.44

This trap indicates Lost Cells on a VP Connection reported by PM.

NTF atmAceAlarmVpMisinsertedCells

1.3.6.1.4.1.164.6.1.12.0.45

This trap indicates Misinserted Cells on a VP Connection reported by PM.

NTF atmAceAlarmVpUAS

1.3.6.1.4.1.164.6.1.12.0.46

This trap is sent upon UAS start or end per VP.

NTF atmAceAlarmVpLoopback

1.3.6.1.4.1.164.6.1.12.0.47

This trap is sent upon OAM LoopBack fail status per VP.

NTF atmAceAlarmVpGCRAViolation

1.3.6.1.4.1.164.6.1.12.0.48

This trap indicates GCRA violation on a VP Connection reported by UPC device.

NTF atmAceAlarmVcContinuityLoss

1.3.6.1.4.1.164.6.1.12.0.56

This trap indicates Loss of Continuity Check on a VC Connection.

NTF atmAceAlarmVcAISReception

1.3.6.1.4.1.164.6.1.12.0.57

This trap indicates AIS Reception on a VC.

NTF atmAceAlarmVcRDIReception

1.3.6.1.4.1.164.6.1.12.0.58

This trap indicates RDI Reception on a VC Connection.

NTF atmAceAlarmVcErroredCells

1.3.6.1.4.1.164.6.1.12.0.59

This trap indicates Errored Cells on a VC Connection reported by PM.

NTF atmAceAlarmVcLostCells

1.3.6.1.4.1.164.6.1.12.0.60

This trap indicates Lost Cells on a VC Connection reported by PM.

NTF atmAceAlarmVcMisinsertedCells

1.3.6.1.4.1.164.6.1.12.0.61

This trap indicates Misinserted Cells on a VC Connection reported by PM.

NTF atmAceAlarmVcUnexpectedCell

1.3.6.1.4.1.164.6.1.12.0.62

This trap indicates an unexpected cell from user or network port.

NTF atmAceAlarmVcUAS

1.3.6.1.4.1.164.6.1.12.0.63

This trap is sent upon UAS start or end per VC.

NTF atmAceAlarmVcLoopback

1.3.6.1.4.1.164.6.1.12.0.64

This trap is sent upon OAM LoopBack fail status per VC.

NTF atmAceAlarmVcGCRAViolation

1.3.6.1.4.1.164.6.1.12.0.65

This trap indicates GCRA violation on a VC Connection reported by UPC device.

radStarSwitch

1.3.6.1.4.1.164.6.1.12.1

radStarSwitchATM25

1.3.6.1.4.1.164.6.1.12.1.1

radStarSwitchATM25L

1.3.6.1.4.1.164.6.1.12.1.2

radStarSwitchATM155

1.3.6.1.4.1.164.6.1.12.1.3

radAtmCsuDsu

1.3.6.1.4.1.164.6.1.12.2

radAmcdE1

1.3.6.1.4.1.164.6.1.12.2.1

radAmcdT1

1.3.6.1.4.1.164.6.1.12.2.2

radAce20E

1.3.6.1.4.1.164.6.1.12.2.3

radAce20T

1.3.6.1.4.1.164.6.1.12.2.4

radAce2005

1.3.6.1.4.1.164.6.1.12.2.5

radAce2002

1.3.6.1.4.1.164.6.1.12.2.6

radAce2002E

1.3.6.1.4.1.164.6.1.12.2.7

radAce2E

1.3.6.1.4.1.164.6.1.12.2.8

radAce2T

1.3.6.1.4.1.164.6.1.12.2.9

radMlAtmE1

1.3.6.1.4.1.164.6.1.12.2.10

radMlAtmT1

1.3.6.1.4.1.164.6.1.12.2.11

radAmc102

1.3.6.1.4.1.164.6.1.12.2.12

radAmc102c

1.3.6.1.4.1.164.6.1.12.2.13

radAce202

1.3.6.1.4.1.164.6.1.12.2.14

radAce

1.3.6.1.4.1.164.6.1.12.3

radAce101

1.3.6.1.4.1.164.6.1.12.3.1

radAce102

1.3.6.1.4.1.164.6.1.12.3.2

radAce50

1.3.6.1.4.1.164.6.1.12.3.3

radAce52

1.3.6.1.4.1.164.6.1.12.3.4

radAce52L

1.3.6.1.4.1.164.6.1.12.3.5

radAce201

1.3.6.1.4.1.164.6.1.12.3.7

radAce3200

1.3.6.1.4.1.164.6.1.12.3.8

radAce3100

1.3.6.1.4.1.164.6.1.12.3.9

radAce3400

1.3.6.1.4.1.164.6.1.12.3.10

radAce3402

1.3.6.1.4.1.164.6.1.12.3.11

radAce3100PSN

1.3.6.1.4.1.164.6.1.12.3.12

radAce3200PSN

1.3.6.1.4.1.164.6.1.12.3.13

radAce3400PSN

1.3.6.1.4.1.164.6.1.12.3.14

radAce3402PSN

1.3.6.1.4.1.164.6.1.12.3.15

radAce3600

1.3.6.1.4.1.164.6.1.12.3.16

radAce3205

1.3.6.1.4.1.164.6.1.12.3.17

radAce3105

1.3.6.1.4.1.164.6.1.12.3.18

radSysLA

1.3.6.1.4.1.164.6.1.13

radLA140

1.3.6.1.4.1.164.6.1.13.1

radLA110

1.3.6.1.4.1.164.6.1.13.2

radLA104

1.3.6.1.4.1.164.6.1.13.3

radLA130

1.3.6.1.4.1.164.6.1.13.4

radLA210

1.3.6.1.4.1.164.6.1.13.5

radSysTerminal

1.3.6.1.4.1.164.6.1.100

agnt

1.3.6.1.4.1.164.6.2

STR agnHwVersion

1.3.6.1.4.1.164.6.2.1

DisplayString

read-write

ASCII string for description and display of the agent hardware version, as it is known by the agent software.The user can update the version upon request when he changes components in the agent's module

I32 agnTrapMask

1.3.6.1.4.1.164.6.2.2

Integer32

read-write

The value of this attribute determines the type of traps the agent should mask and not send to the management console. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.

OCT agnTrapValue

1.3.6.1.4.1.164.6.2.3

OCTET STRING

read-only

The value of the trap decoded in internal RAD format. Full description is given in the Trap definition file

C32 agnChangeCnt

1.3.6.1.4.1.164.6.2.4

Counter32

read-only

The number of changes in system configuration that were reported to the manager since last cold start

OID agnSpecific

1.3.6.1.4.1.164.6.2.5

OBJECT IDENTIFIER

read-only

Object identifier of entity containing additional information regarding this instance.

OCT agnConfigMsg

1.3.6.1.4.1.164.6.2.6

OCTET STRING

read-only

Full configuration message coded in internal RAD application format. This entry describes agent's configuration. For MP-2200 R3, this object describes agent's support of the V5.1 feature: 1 octet ; bit 0 (LSB). '1' - V5.1 feature is supported '0' - V5.1 feature is not supported.

mngTrapIpTable

1.3.6.1.4.1.164.6.2.7

not-accessible

This table indicates the destination address of the traps. Internally it will be limited to ten addresses.

mngEntry

1.3.6.1.4.1.164.6.2.7.1

not-accessible

An entry in table.

I32 mngID

1.3.6.1.4.1.164.6.2.7.1.1

Integer32

read-only

This value indicates an index of a specific IP address

IP mngIP

1.3.6.1.4.1.164.6.2.7.1.2

IpAddress

read-write

This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.

IP mngIPMask

1.3.6.1.4.1.164.6.2.7.1.3

IpAddress

read-write

This value indicates the mask of the destination addresses of the traps.

I32 mngTrapMask

1.3.6.1.4.1.164.6.2.7.1.4

Integer32

read-write

The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.

OCT mngAlarmTrapMask

1.3.6.1.4.1.164.6.2.7.1.5

OCTET STRING

read-write

The value of this object determines the alarm traps that the agent should mask (not send to this manager). The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. For more details on the specific alarm traps masked, see product specification.

U32 mngSnmpTrapUdpPort

1.3.6.1.4.1.164.6.2.7.1.6

Unsigned32

read-write

This variable enables to set the UDP port (socket) used for SNMP traps.

INT agnIndication

1.3.6.1.4.1.164.6.2.8

INTEGER

read-only

Attribute describing the state of the entity the agent is responsible for. In case of a modular entity, the value of this attribute will be according to the component which is in the worst state. The order of severity (from top to bottom) is: critical-> major (or faulty)-> minor-> event-> warning-> normal (off).

INT agnMonitorModeCmd

1.3.6.1.4.1.164.6.2.9

INTEGER

read-write

Setting this attribute to ON, will enforce the agent to change its mode of operation to Monitor Mode

OCT agnLed

1.3.6.1.4.1.164.6.2.10

OCTET STRING

read-only

This entry specifies the LEDs status of the agent module . Each led will be represented by 4 bits where the first 2 bits (left) will specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY)

trapTable

1.3.6.1.4.1.164.6.2.11

not-accessible

This table may include the last few traps generated by the agent, for future retrieval. The table has a limited capacity. If traps are not retrieved in proper time, they will be over-written by new traps. For other devices, it can include generic variables that will be attached to traps as 'accessible-for-notify'.

trapEntry

1.3.6.1.4.1.164.6.2.11.1

not-accessible

An entry in trapTable.

I32 trapID

1.3.6.1.4.1.164.6.2.11.1.1

Integer32

read-only

This object indicates an index of a specific trap. Can be used also for any trap, while trapVal is used as 'accessible-for-notify' or trapNumeric is used.

STR trapVal

1.3.6.1.4.1.164.6.2.11.1.2

DisplayString

read-only

This object is the actual ASCII description of the trap. It can be used also as attached variable of traps, in order to detail in explicit ASCII text, data of the trap. In this case, it is used as 'accessible-for-notify'.

TIK trapTimeSinceOccurrence

1.3.6.1.4.1.164.6.2.11.1.3

TimeTicks

read-only

This object indicates the amount of time passed since the occurrence of the event that triggered this trap.

I32 trapNumeric

1.3.6.1.4.1.164.6.2.11.1.4

Integer32

accessible-for-notify

This object is a numeric general parameter, that can be attached to any trap. Values can be positive or negative.

fileTransfer

1.3.6.1.4.1.164.6.2.12

IP fileServerIP

1.3.6.1.4.1.164.6.2.12.1

IpAddress

read-write

The IP address of the server from which the file is loaded

STR fileName

1.3.6.1.4.1.164.6.2.12.2

DisplayString

read-write

The name of the file to be loaded. For protection, read returns NULL.

INT fileTransCmd

1.3.6.1.4.1.164.6.2.12.3

INTEGER

read-write

The command to be executed on fileName at fileServerIP.

I32 tftpRetryTimeOut

1.3.6.1.4.1.164.6.2.12.4

Integer32

read-write

General Retransmission time-out value (seconds)

I32 tftpTotalTimeOut

1.3.6.1.4.1.164.6.2.12.5

Integer32

read-write

Total Retransmission time-out value (seconds)

INT tftpStatus

1.3.6.1.4.1.164.6.2.12.6

INTEGER

read-write

Status of tftp session. When a session ended with success, the tftpStatus should be endedOk(6). Before restarting a tftp session, the NMS should set the tftpStatus to noOp(2). That's the reason of MAX-ACCESS read-write to this field.

OCT tftpError

1.3.6.1.4.1.164.6.2.12.7

OCTET STRING

read-only

The MSB represents the standard error code. The LSB represents the private error code. 0x0000 is No Error 0x0100 is File Not Found 0x0200 is Access violation 0x0300 is Disk full or allocation exceeded 0x0400 is Illegal TFTP operation 0x0500 is Unknown transfer ID 0x0600 is File already exists 0x0700 is No such user 0x0001 is Server Overflow 0x0002 is No empty UDP port 0x0003 is No empty connection 0x0004 is Illegal File Mode 0x0007 is Illegal PDU size 0x0008 is TFTP Server does not exist 0x0009 is Incorrect File 0x000A is Wrong License format 0x000B is License ID already used

OCT fileTransferToSubSystems

1.3.6.1.4.1.164.6.2.12.8

OCTET STRING

read-write

This object represents the sub-systems the fileTransCmd refers to. It should be used when a system is divided to sub-systems and each sub-system (or part of them) can have a different SW/Configuration. Each bit of this object will represent one of the sub-systems. Bit='1' - APPLY to respective sub-system Bit='0' - DO NOT APPLY to respective sub-system For the meaning of each bit, see product's specification. User will select the sub-systems envolved by filling-in the bits that represent these sub-systems. In this case, the file represented by 'fileName' will include several parts, each representing one of the sub-systems. The agent will refer only to the part/s indicated by this object. 0 Octet Strings = not applicable DEFVAL = 0h for the products that support this object.

STR fileNameWithinProduct

1.3.6.1.4.1.164.6.2.12.9

DisplayString

read-write

The file name used by the product within the product file system.

intSwdlTable

1.3.6.1.4.1.164.6.2.12.10

not-accessible

This parameters table is for internal Software down load. It also includes data about all files contained in the Object from which down-load is performed.

intSwdlEntry

1.3.6.1.4.1.164.6.2.12.10.1

not-accessible

An entry in table.

I32 intSwdlObjIdx

1.3.6.1.4.1.164.6.2.12.10.1.1

Integer32

read-only

The index of the object from which down-load is performed.

I32 intSwdlFileIdx

1.3.6.1.4.1.164.6.2.12.10.1.2

Integer32

read-only

The index of the files included in intSwdlObjIdx. One of these files can be selected to be internally downloaded.

STR intSwdlFileName

1.3.6.1.4.1.164.6.2.12.10.1.3

DisplayString

read-only

The name of the file.

STR intSwdlFileSwVer

1.3.6.1.4.1.164.6.2.12.10.1.4

DisplayString

read-only

The software version of the file.

STR intSwdlSwDate

1.3.6.1.4.1.164.6.2.12.10.1.5

DisplayString

read-only

The software version date of the file.

STR intSwdlSize

1.3.6.1.4.1.164.6.2.12.10.1.6

DisplayString

read-only

The size of the file.

INT intSwdlCmd

1.3.6.1.4.1.164.6.2.12.10.1.7

INTEGER

read-write

The command to down-load a SW file to an object. The Agent will change the value of this MIB object to off(2) automatically, after accepting the command.

OCT intSwdlToSubSystem

1.3.6.1.4.1.164.6.2.12.10.1.8

OCTET STRING

read-write

This object defines the subsystem for download. Bit='1'- APPLY to respective sub system. Bit='0'- DO NOT APPLY to respective sub system. For more details see product specification. For every octet bit0=LSB, bit7=MSB

INT intSwdlCardType

1.3.6.1.4.1.164.6.2.12.10.1.9

INTEGER

read-only

This object defines the Card type that this file is relevant for.

I32 intSwdlFlashIdx

1.3.6.1.4.1.164.6.2.12.10.1.10

Integer32

read-only

The index of the flash memory this file is stored in (1 or 2) (Example: 1= The file is stored in flash No.1). ASMi52 file will always be stored in Flash No.2 (intSwdlFlashIdx=2).

swdlStatusTable

1.3.6.1.4.1.164.6.2.12.11

not-accessible

This parameters table is for software download status. It also includes data about the files down-loaded or attempted to be down-loaded.

swdlStatusEntry

1.3.6.1.4.1.164.6.2.12.11.1

not-accessible

An entry in table.

I32 swdlStatusTypeIdx

1.3.6.1.4.1.164.6.2.12.11.1.1

Integer32

read-only

The index of the down-load type (e.g. external (1) or internal (2)).

I32 swdlStatusIdx

1.3.6.1.4.1.164.6.2.12.11.1.2

Integer32

read-only

The index of the status rows.

STR swdlStatusFileName

1.3.6.1.4.1.164.6.2.12.11.1.3

DisplayString

read-only

The name of the file.

STR swdlStatusSlot

1.3.6.1.4.1.164.6.2.12.11.1.4

DisplayString

read-only

The slot of the updated (or attempted to be updated) object.

STR swdlStatusSubSystem

1.3.6.1.4.1.164.6.2.12.11.1.5

DisplayString

read-only

The subsystem that updated (or attempted to be updated).

I32 swdlStatusStatus

1.3.6.1.4.1.164.6.2.12.11.1.6

Integer32

read-only

The status of the down load process. Value: Fail (2), OK (3), InProcess (4).

STR swdlStatusTime

1.3.6.1.4.1.164.6.2.12.11.1.7

DisplayString

read-only

This MIB parameter indicates the time SW download was finished. The format shuld be YYYY-MM-DD, hh:mm:ss

I32 clearDwldStatusLog

1.3.6.1.4.1.164.6.2.12.12

Integer32

read-write

This object clears the status log. Value: off(2), external(3), internal(4) The Agent will change the value of this MIB object to off(2) automatically, after accepting the command .

autoFileTransfer

1.3.6.1.4.1.164.6.2.12.13

autoFileTransferTable

1.3.6.1.4.1.164.6.2.12.13.1

not-accessible

Scheduling configuration table for Agent initiated file transfer.

autoFileTransferEntry

1.3.6.1.4.1.164.6.2.12.13.1.1

not-accessible

An entry in the table.

INT autoFileTransferType

1.3.6.1.4.1.164.6.2.12.13.1.1.1

INTEGER

read-only

This object defines the type of file to be transferred by agent.

IP autoFileTransferServerIp

1.3.6.1.4.1.164.6.2.12.13.1.1.2

IpAddress

read-write

This object defines the IP Address of the server to which the file is uploaded.

STR autoFileTransferFileName

1.3.6.1.4.1.164.6.2.12.13.1.1.3

SnmpAdminString

read-write

This object defines the name of the file to be uploaded.

INT autoFileTransferScheduling

1.3.6.1.4.1.164.6.2.12.13.1.1.4

INTEGER

read-write

This object defines schedule for TFTP Automatic session(s) initiated by Agent, according to the value selected: now - initiate immediate single session. recurrence- initiate single session 'every M time units'. or 'every N occurrences' or upon both, (earliest event). Time reccurence period (M) is defined by fileTransferTimeRecurrence. Occurrence reccurence (N) is defined by fileTransferOccurrenceRecurrence. Zero value means that the object is not relevant (not taken into account for the recurrence). It is invalid that both will have zero values in our case (recurrence). When both are non zero, file is transferred upon earliest event

I32 autoFileTransferTimeRecurrence

1.3.6.1.4.1.164.6.2.12.13.1.1.5

Integer32

read-write

This object defines time reccurence interval, e.g. M can be 'every M days', 'every M hours' etc. Zero is used to indicate there's no time reccurence (0= notApplicable). This object is taken into account only if autoFileTransferScheduling = recurrence For LA-110 time units are days.

I32 autoFileTransferOccurrenceRecurrence

1.3.6.1.4.1.164.6.2.12.13.1.1.6

Integer32

read-write

This object defines Occurrence reccurence interval, e.g N can be in 'every N alarms', 'every N log entries' etc. zero is used to indicate There's no Event Reccurence. (0= notApplicable) This object is taken into account only if autoFileTransferScheduling = recurrence Occurence Type (Alarms, etc.) is according to autoFileTransferType.

U32 fileTransferServerPort

1.3.6.1.4.1.164.6.2.12.14

Unsigned32

read-write

Server Port number used for File Transfer. Applicable for SFTP. Valid values: 0..65535.

INT fileTransferProtocol

1.3.6.1.4.1.164.6.2.12.15

INTEGER

read-write

File Transfer protocol used.

INT systemReset

1.3.6.1.4.1.164.6.2.13

INTEGER

read-write

Reset action to be performed on the system. - resetMapping - reset SDH/SONET mapping to default for all SDH/SONET links. - resetStandby(6) - can be used only by devices with redundancy on MAIN/CL.

systemTiming

1.3.6.1.4.1.164.6.2.14

STR systemDate

1.3.6.1.4.1.164.6.2.14.1

DisplayString

read-write

System date.

STR systemTime

1.3.6.1.4.1.164.6.2.14.2

DisplayString

read-write

System time.

I32 systemTimeElapsed

1.3.6.1.4.1.164.6.2.14.3

Integer32

read-only

The number of seconds that have elapsed since the beginning of the current error-measurement period. Same for all ports of the device.

systemNtp

1.3.6.1.4.1.164.6.2.14.4

INT systemNtpMode

1.3.6.1.4.1.164.6.2.14.4.1

INTEGER

read-write

This variable represents the NTP Mode.

I32 systemNtpGmt

1.3.6.1.4.1.164.6.2.14.4.2

Integer32

read-write

This variable represents the NTP GMT (Greenwich Mean Time), Possible values range is -12..12. For new devices/versions this variable will be in minutes.

IPt systemNtpServerAddressType

1.3.6.1.4.1.164.6.2.14.4.3

InetAddressType

read-write

This variable represents the NTP Server Address Type.

IP systemNtpServerAddress

1.3.6.1.4.1.164.6.2.14.4.4

InetAddress

read-write

This variable represents the NTP Server Address.

U32 systemNtpUpdateInterval

1.3.6.1.4.1.164.6.2.14.4.5

Unsigned32

read-write

This variable represents the NTP Update Interval, measured in seconds.

INT systemNtpCmd

1.3.6.1.4.1.164.6.2.14.4.6

INTEGER

read-write

This variable represents NTP possible commands. After the Agent accepts a command, it will automatically change the value to off(2).

schedXTable

1.3.6.1.4.1.164.6.2.14.5

not-accessible

An Augment to the Schedule table (schedTable in DISMAN-SCHEDULE-MIB; RFC-3231).

schedXEntry

1.3.6.1.4.1.164.6.2.14.5.1

not-accessible

An entry in the table.

U32 schedYear

1.3.6.1.4.1.164.6.2.14.5.1.1

Unsigned32

read-create

The year during which the scheduled action should take place.

INT schedWeekInMonth

1.3.6.1.4.1.164.6.2.14.5.1.2

INTEGER

read-create

The week in month (schedMonth) during which the scheduled action should take place.

I32 schedParam

1.3.6.1.4.1.164.6.2.14.5.1.3

Integer32

read-create

A Parameter that might be used whenever the scheduled action takes place. For summer-time schedule - This variable represents the time offset (in minutes), meaning: the number of minutes that should be added for summer-time.

systemPort

1.3.6.1.4.1.164.6.2.15

physicalConnectorTable

1.3.6.1.4.1.164.6.2.15.1

not-accessible

This table includes the connector type of ports or interfaces.

physicalConnectorEntry

1.3.6.1.4.1.164.6.2.15.1.1

not-accessible

An entry in table.

I32 portIdx

1.3.6.1.4.1.164.6.2.15.1.1.1

Integer32

read-only

This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.

INT physicalConnector

1.3.6.1.4.1.164.6.2.15.1.1.2

INTEGER

read-only

The connector of the port/interface. other - none of the specified connectors none - no connector.

INT portOptWaveLength

1.3.6.1.4.1.164.6.2.15.1.1.3

INTEGER

read-only

Wave Length of an Optical interface/port in [nm] and specification if Laser or not. notApplicable - for non-optical ports.

INT portOptMode

1.3.6.1.4.1.164.6.2.15.1.1.4

INTEGER

read-only

Laser Mode of an Optical Laser interface/port. notApplicable - for non-Laser ports.

INT portBalance

1.3.6.1.4.1.164.6.2.15.1.1.5

INTEGER

read-write

This object is according to the port Impedance. For T1 - always balanced. For E1 - there are different impedance values for balanced and unbalanced.

INT portDdmSupport

1.3.6.1.4.1.164.6.2.15.1.1.6

INTEGER

read-only

SFP (Small Form Pluggable) port -support Digital Diagnostics Monitoring.

STR portMfgName

1.3.6.1.4.1.164.6.2.15.1.1.7

SnmpAdminString

read-only

(SFP) Port Manufacturer name (Maximum - 16 characters).

U32 portTypicalMaxRange

1.3.6.1.4.1.164.6.2.15.1.1.8

Unsigned32

read-only

Maximum range supported by SFP port, in meter units.

STR physicalConnectorString

1.3.6.1.4.1.164.6.2.15.1.1.9

SnmpAdminString

read-only

(SFP) connector type. It can be Vendor Specific (unknown in advance). Being a string, the object is not affected by any future new connectors. This object will usually not be used for drawing the connector.

STR portVendorPartNo

1.3.6.1.4.1.164.6.2.15.1.1.10

SnmpAdminString

read-only

SFP Vendor Part Number. Being a string, the object is not affected by any future new SFPs.

prtSupervisory

1.3.6.1.4.1.164.6.2.15.2

prtSpTable

1.3.6.1.4.1.164.6.2.15.2.1

not-accessible

A table.

prtSpEntry

1.3.6.1.4.1.164.6.2.15.2.1.1

not-accessible

Supervisory port parameter table.

I32 prtSupervisoryIndex

1.3.6.1.4.1.164.6.2.15.2.1.1.1

Integer32

read-only

The SP port index. For some products, having modules (cards): The LS byte of the integer is the port index 1..255. The MS byte is different than 0 only if the port belongs to a module. In that case it is the module number. For other products' index see their specification.

INT prtSupervisoryRate

1.3.6.1.4.1.164.6.2.15.2.1.1.2

INTEGER

read-write

This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.

INT prtSupervisoryDataBits

1.3.6.1.4.1.164.6.2.15.2.1.1.3

INTEGER

read-write

This attribute indicates the number of data bits in an async frame

INT prtSupervisoryParity

1.3.6.1.4.1.164.6.2.15.2.1.1.4

INTEGER

read-write

This attribute indicates the parity mode in an async frame

INT prtSupervisoryStopBits

1.3.6.1.4.1.164.6.2.15.2.1.1.5

INTEGER

read-write

This attribute indicates the parity mode in an async frame.

INT prtSupervisoryUsage

1.3.6.1.4.1.164.6.2.15.2.1.1.6

INTEGER

read-write

This attribute indicates the usage of the SP port.

INT prtSupervisoryInterface

1.3.6.1.4.1.164.6.2.15.2.1.1.7

INTEGER

read-write

This attribute indicates the supervisory port interface.

INT prtSupervisoryCTS

1.3.6.1.4.1.164.6.2.15.2.1.1.8

INTEGER

read-write

CTS line state.

INT prtSupervisoryDcdDelay

1.3.6.1.4.1.164.6.2.15.2.1.1.9

INTEGER

read-write

DCD delay in msec.

INT prtSupervisoryDSR

1.3.6.1.4.1.164.6.2.15.2.1.1.10

INTEGER

read-write

DSR line state.

INT prtSupervisoryRoutProtocol

1.3.6.1.4.1.164.6.2.15.2.1.1.11

INTEGER

read-write

This attribute indicates the routing protocol of the port. notApplicable - for DP.

prtPerformance

1.3.6.1.4.1.164.6.2.15.3

prtPerfTable

1.3.6.1.4.1.164.6.2.15.3.1

not-accessible

This table includes G.826 ports or interfaces.

prtPerfEntry

1.3.6.1.4.1.164.6.2.15.3.1.1

not-accessible

An entry in table.

I32 prtPerfIdx

1.3.6.1.4.1.164.6.2.15.3.1.1.1

Integer32

read-only

This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.

INT prtPerfPeriodRef

1.3.6.1.4.1.164.6.2.15.3.1.1.2

INTEGER

read-only

This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. lastPeriod - the period between last two commands of prtPerfSaveAndResetCmd. - If only one command occured since Start-up: the period between Start-up and last command. - If no command occured since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.

I32 prtPerfElapsedTime

1.3.6.1.4.1.164.6.2.15.3.1.1.3

Integer32

read-only

Elapsed Time in seconds. - for prtPerfPeriodRef=currentPeriod: The period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. - for prtPerfPeriodRef=lastPeriod: The value of prtPerfElapsedTime when last prtPerfSaveAndResetCmd was received.

I32 prtPerfUAS

1.3.6.1.4.1.164.6.2.15.3.1.1.4

Integer32

read-only

Number of Unavailable Seconds for the reference period (prtPerfPeriodRef).

I32 prtPerfES

1.3.6.1.4.1.164.6.2.15.3.1.1.5

Integer32

read-only

Number of Errored Seconds for the reference period (prtPerfPeriodRef).

I32 prtPerfSES

1.3.6.1.4.1.164.6.2.15.3.1.1.6

Integer32

read-only

Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef).

I32 prtPerfBBE

1.3.6.1.4.1.164.6.2.15.3.1.1.7

Integer32

read-only

Number of Background Block (or Frame) Errors for the reference period (prtPerfPeriodRef).

I32 prtPerfBlocksPerSec

1.3.6.1.4.1.164.6.2.15.3.1.1.8

Integer32

read-only

Blocks per second (or frames per second) of the port/interface indicated by portIdx. This object is constant for a certain port/interface. It is not affected by the prtPerfPeriodRef index.

TIK prtPerfTimeTag

1.3.6.1.4.1.164.6.2.15.3.1.1.9

TimeTicks

read-only

Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was executed. This object is applicable only for prtPerfPeriodRef=lastPeriod. For prtPerfPeriodRef=currentPeriod, the value will always be 0.

INT prtPerfSaveAndResetCmd

1.3.6.1.4.1.164.6.2.15.3.1.1.10

INTEGER

read-write

A command per port/interface, to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. This object is applicable only for prtPerfPeriodRef=currentPeriod. Setting this object to on(3) for prtPerfPeriodRef=last, will cause the agent to return: Bad Value response. When setting validly this object to on(3), agent will perform the required command and will reset automatically the value of this object to off(2). Setting this object to off(2), will do nothing.

prtTest

1.3.6.1.4.1.164.6.2.15.4

prtTestTable

1.3.6.1.4.1.164.6.2.15.4.1

not-accessible

This table includes test data for ports or interfaces.

prtTestEntry

1.3.6.1.4.1.164.6.2.15.4.1.1

not-accessible

An entry in table.

I32 prtTestIdx

1.3.6.1.4.1.164.6.2.15.4.1.1.1

Integer32

read-only

This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.

I32 prtTestCmdAndStatus

1.3.6.1.4.1.164.6.2.15.4.1.1.2

Integer32

read-write

Setting this object to a value as detailed further on (except 0) will initiate a test on the specific port. The test/s requested will be set according to the respective bit. The value of this object will be a sum of (2**n), where n is the Bit: TEST BIT VALUE ----------- --- ------ reserved 0 1 PayloadLoop=RLB 1 (=Remote Loopback) 2 LineLoop=DIG 2 (=Digital) 4 OtherLoop 3 8 InwardLoop=LLB 4 (=Local Loopback) 16 BERT 5 32 LC 6 64 ToneInjection 7 128 Inband 8 256 BERT Remote (or E1/T1 RLB) 9 512 Downstream-AIS (or E1/T1 LLB) 10 1024 Upstream-AIS 11 2048 Rem-Loop-on-Rem-Unit 12 4096 MacSwapLoop 13 8192 OamETHLoopback 14 16384 OamETHLinkTrace 15 32768 e.g : If the requested value is 20 -> 010100 -> Bits 2 & 4 are set -> the requested tests are : LineLoopback=DIG InwardLoopback=LLB Not all tests combinations are valid. For valid test combination, see each product's specification. For LRS52, only single test is allowed simultaneously The terminology and order of the first tests (except BERT) is according to the one used for Test Status of DS1 and DS3 standards. The notations : RLB, LLB, DIG are the most used in RAD's products, but they can be different. For exact definition see product's spec. Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port. When no test is running on the port, the Get value (test status) will be 0. PayloadLoop=RLB The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. LineLoop=DIG The received signal at this interface does not go through the device (minimum penetration) but is looped back out. OtherLoop Loopbacks that are not defined here. InwardLoop=LLB The sent signal at this interface is looped back through the device. LC This loop is applicable only for HSSI interface, towards the router . ToneInjection This loop is applicable for analog voice (like FXS). Downstream-AIS E1 AIS signal (all ones) is transmitted in the relevant channel toward the STM-1 line. Upstream-AIS E1 AIS signal (all ones) is generated in the relevant channel toward the local received tributary channel output Rem-Loop-on-Rem-Unit Request from far end device to activate remote loopback towards near-end device MacSwapLoop This loop is applicable for ethernet port. Loop is implemented by swapping the MAC addresses of the incoming message. OamETHLoopback Ethernet Loopback is used to verify connectivity of a MEP with a MIP or peer MEP(s) (ITU-T Y.1731, Clause 7.2). OamETHLinkTrace Ethernet Link Trace is an on-demand OAM function which can be used for the two following purposes: - Adjacent Relation Retrieval - Fault Localization (ITU-T Y.1731, Clause 7.3).

I32 prtBertCounter

1.3.6.1.4.1.164.6.2.15.4.1.1.3

Integer32

read-only

This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counter starts from zero (0) anytime BERT is initiated.

INT prtTestInitiator

1.3.6.1.4.1.164.6.2.15.4.1.1.4

INTEGER

read-only

This object indicates who initiated this port's test/s.

I32 prtTestTimeout

1.3.6.1.4.1.164.6.2.15.4.1.1.5

Integer32

read-write

This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. For RICi-E1T1, RICi-E3T3 the measurement unit is in seconds. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever

INT prtTestVctRxResult

1.3.6.1.4.1.164.6.2.15.4.1.1.6

INTEGER

read-only

This object indicates the result of the Vct on the cable connected to the RX connector.

INT prtTestVctTxResult

1.3.6.1.4.1.164.6.2.15.4.1.1.7

INTEGER

read-only

This object indicates the result of the Vct on the cable connected to the TX connector.

I32 prtTestVctRxDistance

1.3.6.1.4.1.164.6.2.15.4.1.1.8

Integer32

read-only

This object indicates the distance in Meters to the RX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.

I32 prtTestVctTxDistance

1.3.6.1.4.1.164.6.2.15.4.1.1.9

Integer32

read-only

This object indicates the distance in Meters to the TX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.

INT prtTestVctCmd

1.3.6.1.4.1.164.6.2.15.4.1.1.10

INTEGER

read-write

Vct command. on (3) = Start Vct on both cables connected to RX and TX connectors of this port. Agent will perform the required command and change automatically the value of this object to off(2).

I32 prtTestVctRxCrossPair

1.3.6.1.4.1.164.6.2.15.4.1.1.11

Integer32

read-only

This object should be equal to the Index (prtTestIdx) of the Rx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair. This object was especially created for ETX-202. Currently not in use.

I32 prtTestVctTxCrossPair

1.3.6.1.4.1.164.6.2.15.4.1.1.12

Integer32

read-only

This object should be equal to the Index (prtTestIdx) of the Tx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.

U32 prtTestActivationDelay

1.3.6.1.4.1.164.6.2.15.4.1.1.13

Unsigned32

read-write

This object is applicable only when a single test is running. It indicates test activation delay in seconds. A Value of 0 indicates that the test starts immediately.

INT prtTestMacSwapLoopDataMode

1.3.6.1.4.1.164.6.2.15.4.1.1.14

INTEGER

read-write

This object defines which part of the data will be looped back.

I32 prtTestMacSwapLoopVlanId

1.3.6.1.4.1.164.6.2.15.4.1.1.15

Integer32

read-write

This object specifies the VLAN ID for prtTestMacSwapLoopDataMode=specificVlan.

INT prtTestMacSwapLoopDirection

1.3.6.1.4.1.164.6.2.15.4.1.1.16

INTEGER

read-write

This object defines the direction of the performed loopback. In ETX102 'local' corresponds to Ingress loop (either on User port or on Network port), and 'remote' corresponds to Egress loop (either on User port or on Network port).

MAC prtTestMacSwapLoopDestAddr

1.3.6.1.4.1.164.6.2.15.4.1.1.17

MacAddress

read-write

Configures the MAC address that will be sent in the Destination field of the packet in the outgoing direction.

MAC prtTestMacSwapLoopSrcAddr

1.3.6.1.4.1.164.6.2.15.4.1.1.18

MacAddress

read-write

Configures the MAC address that will be sent in the Source field of the packet in the outgoing direction.

U32 prtTestOamMinRoundTripDelay

1.3.6.1.4.1.164.6.2.15.4.1.1.19

Unsigned32

read-only

The mininal value of round trip delay of loopback message for a session of OAM loopback.Units are msec.

U32 prtTestOamMaxRoundTripDelay

1.3.6.1.4.1.164.6.2.15.4.1.1.20

Unsigned32

read-only

The maximum value of round trip delay of loopback message for a session of OAM loopback.Units are msec.

U32 prtTestOamAvgRoundTripDelay

1.3.6.1.4.1.164.6.2.15.4.1.1.21

Unsigned32

read-only

The average round trip delay of loopback message for a session of OAM loopback.Units are msec.

U32 prtTestOamTxInterval

1.3.6.1.4.1.164.6.2.15.4.1.1.22

Unsigned32

read-write

Indicates the interval between loopback sent messages.Units are msec.

IP prtTestDestinationIpAddress

1.3.6.1.4.1.164.6.2.15.4.1.1.23

IpAddress

read-write

Indicates the destination IP Address in the transmitted messages that are looped back.

U32 prtTestTTL

1.3.6.1.4.1.164.6.2.15.4.1.1.24

Unsigned32

read-write

Time-to-live.Number of hops the loopback message will go through the net before deciding to discard it.

U32 prtTestBwProfile

1.3.6.1.4.1.164.6.2.15.4.1.1.25

Unsigned32

read-write

Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test in order to limit the traffic that is looped back.

prtParam

1.3.6.1.4.1.164.6.2.15.5

prtParamTable

1.3.6.1.4.1.164.6.2.15.5.1

not-accessible

This table includes general port parameters. The meaning is different for every product that supports it due to a general parameter - prtControlCnfg. For ACE2002: -This table is used as a mechanism to create the next interface index. The algorithm description: The NMS will send the agent the following get command: get(nextIfIndex.index), where index=interface on which the new index is dependent on. Upon this command the agent will generate and return the new index to the NMS. - This table is partially supported according to the interface type. Upon getNext function the irrelevant parameters will be skipped.

prtParamEntry

1.3.6.1.4.1.164.6.2.15.5.1.1

not-accessible

An entry in table.

I32 prtParamIdx

1.3.6.1.4.1.164.6.2.15.5.1.1.1

Integer32

read-only

This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. For ACE2002: This parameter is the physical layer ifIndex of the slot on which the NMS requires the next interface index.

I32 prtControlCnfg

1.3.6.1.4.1.164.6.2.15.5.1.1.2

Integer32

read-write

This object may be used for port RW general parameter/s. For detailed meaning, see product's spec. Supported by: PRBi-E3/T3. For ACE2002: This parameter will include the value of the new index generated by agent. For Optimux-T3 and OP-155-1: This parameter will be used for Release Remote LLB Command: on=2= Set value only. Command to release LLB of Remote Unit. Agent will return automatically to 'off' value after performing the command. off=3=Get value only. For LA140 This parameter will be used as EchoCanceler per timeslot off = 2 Echo Canceler is disabled on = 3 Echo Canceler is enabled For FCD-155 This parameter will be used to select the port that is clock source for a PDH port, For E1/T1 PDH VC12/VT1.5 = 2 SDH/SONET = 3 For E3/T3 PDH VC3/DS3 = 2 SDH/SONET = 3 For ACE-52 This parameter will be used as Transmit Frame Type, i.e. which type of frame the corresponding bridge port will transmit: Untagged = 2 Tagged = 3 .

INT prtParamClkSrc

1.3.6.1.4.1.164.6.2.15.5.1.1.3

INTEGER

read-write

The source of Transmit Clock. 'loopTiming' or 'loopback' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' or 'internal' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' or 'external' indicates that recovered receive clock from another card or interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'master' and 'fallback' values may be used RO to indicate active clock. 'station' - indicate clock received from station port is used as transmit clock.

INT prtParamPhantom

1.3.6.1.4.1.164.6.2.15.5.1.1.4

INTEGER

read-write

Power feeding to another device.

INT prtParamResetStatsCmd

1.3.6.1.4.1.164.6.2.15.5.1.1.5

INTEGER

read-write

Reset statistics of the selected port.

TIM prtParamLastResetStatsTime

1.3.6.1.4.1.164.6.2.15.5.1.1.6

TimeStamp

read-only

The value of MIB II's sysUpTime object at the last time that prtParamResetStatsCmd was Set to on(3) for this port. If prtParamResetStatsCmd was never Set to on(3) since last re-initialization of the agent, then this object contains a zero value. This object enables calculating the running time of Statistics counters for this port, by: [sysUpTime-prtParamLastResetStatsTime]. For some devices other types of 'Reset' may affect this parameter

INT prtParamInterfaceType

1.3.6.1.4.1.164.6.2.15.5.1.1.7

INTEGER

read-write

The type of the port.

INT prtParamClearAlarm

1.3.6.1.4.1.164.6.2.15.5.1.1.8

INTEGER

read-write

Setting this attribute to ON, will enforce a clear operation on the Port Alarms. Upon completion, the value will automatically change to off(2).

OCT prtParamLeds

1.3.6.1.4.1.164.6.2.15.5.1.1.9

OCTET STRING

read-only

This entry specifies the LEDs status of the port. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.

INT prtParamLineLength

1.3.6.1.4.1.164.6.2.15.5.1.1.10

INTEGER

read-write

Line Length of the line connected to this port.

INT prtParamUsage

1.3.6.1.4.1.164.6.2.15.5.1.1.11

INTEGER

read-write

Defines whether this port works as User port or as Network port.

INT prtParamMappingMode

1.3.6.1.4.1.164.6.2.15.5.1.1.12

INTEGER

read-write

This object defines path protection on SONET/SDH link Auto - SONET/SDH mapping for port is copied automatically to same TU on the redundant SONET/SDH local (reside on same slot) link by agent. Manual - the user can configure the redundant mapping for port on the same link or to the other link on any TU Adjacent - similar to auto, but mapping is copied automatically by agent to link on adjacent slot .

INT prtParamAlarmIndication

1.3.6.1.4.1.164.6.2.15.5.1.1.13

INTEGER

read-only

This object indicates status-aggregation of non-masked alarms associated with all interface layers, related to this physical port. When at least one non-masked alarm exists on any layer, value of this object is on (3). Indication will be off (2) only when there's no active non-masked alarm on any interface layer related to this port. Masking an Alarm, will consider it as not exist for this indication. Example: When a port has an ATM higher layer and at least one VC has alarm, value of this object will be on (3)

OCT prtParamClkQualityLevel

1.3.6.1.4.1.164.6.2.15.5.1.1.14

OCTET STRING

read-only

This parameter indicates quality level of clock signal. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows (when bit1=0): Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit)- Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization) 0001 PRS (=ST1 = Stratum 1 Traceable) 0111 ST2 (Stratum 2 Traceable) 1010 ST3 (Stratum 3 Traceable) 1100 SMC (SONET Minimum Clock Traceable) 1101 Stratum 3E Traceable bit1 = '1' - indicates all octet is Not Applicable

INT prtParamClkWaveShape

1.3.6.1.4.1.164.6.2.15.5.1.1.15

INTEGER

read-write

Wave shape of station clock source signal.

INT prtParamStatus

1.3.6.1.4.1.164.6.2.15.5.1.1.16

INTEGER

read-only

Station clock source Status.

I32 prtParamSignalLevel

1.3.6.1.4.1.164.6.2.15.5.1.1.17

Integer32

read-only

This object indicates signal level (in thenth of dB units) on selected port.

OCT prtParamClkUserQualityLevel

1.3.6.1.4.1.164.6.2.15.5.1.1.18

OCTET STRING

read-write

This parameter allows user to mark quality level of clock. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows: Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit) Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization)

U32 prtParamDataRate

1.3.6.1.4.1.164.6.2.15.5.1.1.19

Unsigned32

read-write

Rate of serial data port (V.11, V.24, V.35) in kbps units.

INT prtParamLoopDetect

1.3.6.1.4.1.164.6.2.15.5.1.1.20

INTEGER

read-write

Enable/disable Loop Detection on a port. Examples of ports: physical, Channelized Bundle over TDM Uplink, Bridge Ports.

OCT prtParamActUponLoopDetect

1.3.6.1.4.1.164.6.2.15.5.1.1.21

OCTET STRING

read-write

This parameter is used to indicate which actions should be taken in case a loop is detected in the network the port is part of. Each action is represented by a bit. Currently defined (for RIC155GE/RIC622GE): Bit 0 - Transmit Shut Down Bit 1 - Forward Alarms If bit value = '1' then the action is taken. If bit value = '0' then the actions is not taken.

INT prtParamPSNLayer

1.3.6.1.4.1.164.6.2.15.5.1.1.22

INTEGER

read-write

This object indicates the network layer from which clock is derived.

INT prtParamRxSsm

1.3.6.1.4.1.164.6.2.15.5.1.1.23

INTEGER

read-write

This object indicates if Station Clock SSM messages received will serve as criteria for clock selection.

INT prtParamClkSsmRxSource

1.3.6.1.4.1.164.6.2.15.5.1.1.24

INTEGER

read-write

This object indicates the Sa-bit of the E1 frame, in which SSM messages are carried.

U32 prtParamFarEndDevice

1.3.6.1.4.1.164.6.2.15.5.1.1.26

Unsigned32

read-write

Programmed Far-End device connected to this port. This object is relevant for products having multiple DBs. It will enable configuring offline, the relevant data. For MP-4100, LRS-102 OP-108/106 cards, the options will be: 1 = None (when a port is not connected to any remote device) 2 = OP-108 3 = OP-108/ETH 4 = OP-106 5 = OP-106/ETH 6 = card of MP or LRS-102

INT prtParamTxClk

1.3.6.1.4.1.164.6.2.15.5.1.1.27

INTEGER

read-write

enable/disable station clock signal output.

prtIP

1.3.6.1.4.1.164.6.2.15.6

prtIpParamTable

1.3.6.1.4.1.164.6.2.15.6.1

not-accessible

A table - Parameters for IP Ports.

prtIpParamEntry

1.3.6.1.4.1.164.6.2.15.6.1.1

not-accessible

An entry in table.

I32 prtIpParamConfigIdx

1.3.6.1.4.1.164.6.2.15.6.1.1.1

Integer32

read-only

This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). For products having Agent and Edit configurations, Write operation for the table entries is allowed only to Config=255.

I32 prtIpParamSlotIdx

1.3.6.1.4.1.164.6.2.15.6.1.1.2

Integer32

read-only

This object indicates a unique number of the slot position in which the module is inserted. notApplicable = 255 (for products that don't have slots). For KM: kmxMlA (103), kmxMlB (104).

I32 prtIpParamIdx

1.3.6.1.4.1.164.6.2.15.6.1.1.3

Integer32

read-only

This object indicates a unique Port Index.

IP prtIpParamHostIP

1.3.6.1.4.1.164.6.2.15.6.1.1.4

IpAddress

read-write

The host interface IP address.

IP prtIpParamHostMask

1.3.6.1.4.1.164.6.2.15.6.1.1.5

IpAddress

read-write

The host interface subnet mask.

IP prtIpParamDefaultGateway

1.3.6.1.4.1.164.6.2.15.6.1.1.6

IpAddress

read-write

Default Gateway's IP Address.

INT prtIpParamMediaMode

1.3.6.1.4.1.164.6.2.15.6.1.1.7

INTEGER

read-only

This object indicates the real Media Mode.

INT prtIpParamMediaRate

1.3.6.1.4.1.164.6.2.15.6.1.1.8

INTEGER

read-only

This object indicates the real Media Rate (Mbps).

INT prtIpParamMngVlanSupport

1.3.6.1.4.1.164.6.2.15.6.1.1.9

INTEGER

read-write

Management VLAN support (Tagging). no - No support of VLAN Tagging. yes - 4 VLAN bytes will be added to the frame.

I32 prtIpParamMngVlanId

1.3.6.1.4.1.164.6.2.15.6.1.1.10

Integer32

read-write

Management VLAN ID.

I32 prtIpParamMngVlanPriority

1.3.6.1.4.1.164.6.2.15.6.1.1.11

Integer32

read-write

Management VLAN Frame priority.

INT prtIpParamRingMode

1.3.6.1.4.1.164.6.2.15.6.1.1.12

INTEGER

read-write

This object indicates If Ring Mode is enabled or not.

INT prtIpParamProtIpEnable

1.3.6.1.4.1.164.6.2.15.6.1.1.13

INTEGER

read-write

This object indicates whether a list of Protected IP Addresses is enabled or not. This object is applicable only if prtIpParamRingMode=enable.

INT prtIpParamTrafficPriority

1.3.6.1.4.1.164.6.2.15.6.1.1.14

INTEGER

read-write

This object indicates the traffic priority of this port.

IP prtIpParamRemoteIP

1.3.6.1.4.1.164.6.2.15.6.1.1.15

IpAddress

read-write

This is the IP Address of the remote device that is connected to the current device (Point to Point Application). It is used for sending OAM packets on the LAN to the remote side in order to check that the connection is OK.

INT prtIpParamMaxTxBandwidth

1.3.6.1.4.1.164.6.2.15.6.1.1.16

INTEGER

read-write

This object shows the Max Bandwidth allowed on the LAN. Full - means that a Maximum of 100 Mega Byte Rate may go through the LAN. e1(3) means that the maximum is an E1 rate. t1(4) is for a maximum of a T1 rate.

I32 prtIpParamTos

1.3.6.1.4.1.164.6.2.15.6.1.1.17

Integer32

read-write

TOS = Type of Service transmitted. Valid values: 0..255.

INT prtIpParamConnect

1.3.6.1.4.1.164.6.2.15.6.1.1.18

INTEGER

read-write

Port Connection.

I32 prtIpParamAgingTime

1.3.6.1.4.1.164.6.2.15.6.1.1.19

Integer32

read-write

Aging Time in seconds.

INT prtIpParamEncapsulationProt

1.3.6.1.4.1.164.6.2.15.6.1.1.20

INTEGER

read-write

Encapsulation Protocol.

I32 prtIpParamEncapProtPort

1.3.6.1.4.1.164.6.2.15.6.1.1.21

Integer32

read-write

Encapsulation Protocol Port (TCP/UDP Port).

INT prtIpParamVlanSupport

1.3.6.1.4.1.164.6.2.15.6.1.1.22

INTEGER

read-write

VLAN support (Tagging). 'no' - No support of VLAN Tagging. 'yes' - 4 VLAN bytes will be added to the frame.

I32 prtIpParamVlanId

1.3.6.1.4.1.164.6.2.15.6.1.1.23

Integer32

read-write

VLAN Identifier.

I32 prtIpParamVlanPriority

1.3.6.1.4.1.164.6.2.15.6.1.1.24

Integer32

read-write

VLAN Frame priority.

I32 prtIpParamDoubleTagVlanId

1.3.6.1.4.1.164.6.2.15.6.1.1.25

Integer32

read-write

VLAN Identifier of the Double Tagging VLAN.

I32 prtIpParamDoubleTagVlanPriority

1.3.6.1.4.1.164.6.2.15.6.1.1.26

Integer32

read-write

VLAN Frame priority of the Double Tagging VLAN.

INT prtIpParamVlanTagging

1.3.6.1.4.1.164.6.2.15.6.1.1.27

INTEGER

read-write

VLAN Tagging. 'unmodified' - No change will be done to the Frame. 'tag' - Add Tag to Untagged Frames. 'doubleTag' - Add Tag to all Frames. 'doubleTagAndFallBack' - Double Tagging will have different rules for VLANs that this port is member in, than these it is not a member in. 'untag' - Remove Tag from tagged frames.

I32 prtIpParamRateLimit

1.3.6.1.4.1.164.6.2.15.6.1.1.28

Integer32

read-write

The maximum rate permitted to transfer via this port, in Kbps.

I32 prtIpParamDefInterface

1.3.6.1.4.1.164.6.2.15.6.1.1.29

Integer32

read-write

The Default Interface for packets with unresolved destination subnet. For internal-X port: 100 + X .

INT prtIpParamMng

1.3.6.1.4.1.164.6.2.15.6.1.1.30

INTEGER

read-write

This object indicates whether Management is enabled/disabled via this port.

I32 prtIpParamFloodedRateLimit

1.3.6.1.4.1.164.6.2.15.6.1.1.31

Integer32

read-write

The maximum rate permitted to transfer broadcast, multicast, and unicast flooded frames via this port, in Kbps. 0 - Disable. In Ipmux14 this parameter is applicable when prtIpParamRateLimit=0 (disable).

U32 prtIpParamBurstSize

1.3.6.1.4.1.164.6.2.15.6.1.1.32

Unsigned32

read-write

The burst size that the port can support beyond rate limitation determined in prtIpParamRateLimit. Burst Size is measured in bytes.

INT prtIpParamLimitPacketType

1.3.6.1.4.1.164.6.2.15.6.1.1.33

INTEGER

read-write

The packet type that will be rate limited. Rate limitation determined in prtIpParamRateLimit. all - All packet types are rate limited. broadMultiFloodedUnicast - Broadcast, Multicast and Flooded Unicast packets are rate limited. broadcastMulticast - Broadcast and Multicast packets are rate limited. broadcast - Broadcast packets are rate limited.

I32 prtIpParamKeepAliveInterval

1.3.6.1.4.1.164.6.2.15.6.1.1.34

Integer32

read-write

This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.

I32 prtIpParamKeepAliveThresh

1.3.6.1.4.1.164.6.2.15.6.1.1.35

Integer32

read-write

This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.

I32 prtIpParamP2pKeepAliveVlanId

1.3.6.1.4.1.164.6.2.15.6.1.1.36

Integer32

read-write

Dedicated VLAN ID for keep alive messages.

I32 prtIpParamP2pKeepAliveVlanPrio

1.3.6.1.4.1.164.6.2.15.6.1.1.37

Integer32

read-write

VLAN priority for P2P keep alive messages .

MAC prtIpParamRingAdjacentMacAddr

1.3.6.1.4.1.164.6.2.15.6.1.1.38

MacAddress

read-only

The MAC address of the adjacent NE connected to this port in an ETH ring. If the port is not a member of a ring, the value of this parameter will be 00-00-00-00-00-00.

prtClkSrc

1.3.6.1.4.1.164.6.2.15.7

prtClkSrcTable

1.3.6.1.4.1.164.6.2.15.7.1

not-accessible

A table - Parameters for master and fallback clock source of ports .

prtClkSrcEntry

1.3.6.1.4.1.164.6.2.15.7.1.1

not-accessible

An entry in table.

I32 prtClkSrcCnfgIdx

1.3.6.1.4.1.164.6.2.15.7.1.1.1

Integer32

not-accessible

This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.

I32 prtClkSrcPrtIdx

1.3.6.1.4.1.164.6.2.15.7.1.1.2

Integer32

not-accessible

This object indicates a unique Port Index (receiving clock). Refer to device specification for port Index

INT prtClkSrcIdx

1.3.6.1.4.1.164.6.2.15.7.1.1.3

INTEGER

not-accessible

An index in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters

INT prtClkSrcMode

1.3.6.1.4.1.164.6.2.15.7.1.1.4

INTEGER

read-write

This entry indicates the source the nodal timing is locked to.

I32 prtClkSrcPrt

1.3.6.1.4.1.164.6.2.15.7.1.1.5

Integer32

read-write

This entry is valid only when working in rxClk mode. It specifies the port from which the clock willl be taken. Refer to device specification for source port Index

opticalPort

1.3.6.1.4.1.164.6.2.15.8

optPrtMonitorTable

1.3.6.1.4.1.164.6.2.15.8.1

not-accessible

A table - optical port (e.g SFP) monitoring parameters, according to SFF-8472 Specification for Diagnostic Monitoring Interface for Optical Xcvrs. and ITU-T rec. G.958

optPrtMonitorEntry

1.3.6.1.4.1.164.6.2.15.8.1.1

not-accessible

An entry in table.

I32 optPrtMonitorPrtIdx

1.3.6.1.4.1.164.6.2.15.8.1.1.1

Integer32

not-accessible

This object indicates a unique (optical) Port Index . Refer to device specification for port Index.

INT optPrtMonitorSample

1.3.6.1.4.1.164.6.2.15.8.1.1.2

INTEGER

not-accessible

This index indicates historic and current values - minimum, maximum and actual (current) value.

I32 optPrtMonitorTxPower

1.3.6.1.4.1.164.6.2.15.8.1.1.3

Integer32

read-only

Transmitted optical power level. Value is given in units of hundredth (1/100) of dBm.

I32 optPrtMonitorLaserBias

1.3.6.1.4.1.164.6.2.15.8.1.1.4

Integer32

read-only

LASER bias current level. Value is given in units of microAmper (uA).

I32 optPrtMonitorLaserTemp

1.3.6.1.4.1.164.6.2.15.8.1.1.5

Integer32

read-only

LASER temperature level, in hundredth (1/100) (C) degrees.

I32 optPrtMonitorRxPower

1.3.6.1.4.1.164.6.2.15.8.1.1.6

Integer32

read-only

Received optical power in units of hundredth (1/100) of dBm.

I32 optPrtMonitorSupplyVoltage

1.3.6.1.4.1.164.6.2.15.8.1.1.7

Integer32

read-only

Supply voltage, in hundredth (1/100) of volts (V).

optPrtCnfgTable

1.3.6.1.4.1.164.6.2.15.8.2

not-accessible

A table - optical port configuration

optPrtCnfgEntry

1.3.6.1.4.1.164.6.2.15.8.2.1

not-accessible

An entry in table.

U32 optPrtCnfgIdx

1.3.6.1.4.1.164.6.2.15.8.2.1.1

Unsigned32

not-accessible

This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.x.

U32 optPrtCnfgPrtIdx

1.3.6.1.4.1.164.6.2.15.8.2.1.2

Unsigned32

not-accessible

This object indicates a unique (optical) Port Index . Refer to device specification for port Index.

INT optPrtCnfgALS

1.3.6.1.4.1.164.6.2.15.8.2.1.3

INTEGER

read-write

enable/disable Automatic Laser Shutdown

INT systemResetAllStatsCmd

1.3.6.1.4.1.164.6.2.16

INTEGER

read-write

Reset statistics of all ports and connections of the device.

INT systemClearTablesCmd

1.3.6.1.4.1.164.6.2.17

INTEGER

read-write

tempCnfgTables - Set *RowStatus = destroy for all entries of some tables having *RowStatus object, for temporary configuration only! (255). For the relevant tables, see product's specification. This object should be used by WAN product applications before performing the Update operation, in order to clear old entries of these tables. For MP-104/204 the entries will be destroyed for cnfg=1. off - agent will automatically change to this value, after performing the command.

I32 systemParameter

1.3.6.1.4.1.164.6.2.18

Integer32

read-write

This parameter can be used for different purposes: - TELNET session time-out in seconds. - Ace20: when trying to create row in a table that already has row with the same values, if set of values has to be unique in table, this attribute is set to the index of the existing row. - Optimux-T3: when CH interfaces are RJ-45, user can select via this object, the interface type for each Group of channels: T1 or E1: The selection will be a sum of the following Bits. '0' = T1 '1' = E1 Bit Group Value for each Bit having '1' 1 1 (CH-1..CH-8) 1 2 2 (CH-9..CH-12) 2 3 3 (CH-13..CH-20) 4 4 4 (CH-21..CH-28) 8 Examples: 15 = all Groups are selected to be E1 6 = Group 2 and Group 3 are selected to be E1 (Group 1 and Group 4 are T1). - FCD-A, FCD-M: user can select via this object the configuration used for Get values of MSDSL parameters that don't have configuration index. 1 =active configuration 255=temporary configuration. Set of this object should be done before Getting the MSDSL RW parameters. - Ace2002: This parameter indicates the number of intervals that were successfully uploaded upon statistics collection session. - FCD-IP, WR, FCD-IPD, LA-240: This parameter indicates whether Telnet Access is enabled/disabled: Values: 2 - Telnet Access is Disabled. 3 - Telnet Access is Enabled. -Vmux-110: This parameter value equals to maximum number of bundles. -Optimux-155: Simmilar usage to Optimux T3. user can select via this object, interface type T1 or E1 for each Group of channels (LIU): LIU group consists of 7 channels. Up to 12 LIUs are represented (84 T1 Channels). The selection will be a sum of the 2**n For each bit:'0' = T1 ,'1' = E1 Bit Group 1 1 (CH-1 .. CH-7) 2 2 (CH-8 .. CH-14) 3 3 (CH-15 ..CH-21) ... 9 9 (CH-56.. CH-63) ... 10 10 (CH-64..CH-70) 11 11 (CH-71..CH-77) 12 12 (CH-78..CH-84)

OCT agnGlobalAlarmMask

1.3.6.1.4.1.164.6.2.19

OCTET STRING

read-write

The value of this attribute determines the alarm traps the agent should mask and not send to the managers. Each bit from a certain octet represents a certain alarm.

INT alarmSeverity

1.3.6.1.4.1.164.6.2.20

INTEGER

read-only

This object specifies the severity of the alarms.

INT alarmState

1.3.6.1.4.1.164.6.2.21

INTEGER

read-only

.

INT agnTestStatus

1.3.6.1.4.1.164.6.2.22

INTEGER

read-only

Indicates the current test status (for all levels: system, card, port). This attribute will be set to: on(3): when there is at least one test in progress on the system/card/port off(2): when there is NO test in progress on the system/card/port

INT systemSaveAndResetAllStatsCmd

1.3.6.1.4.1.164.6.2.23

INTEGER

read-write

on - a command to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. off - agent will automatically change to this value, after performing the command.

IP systemDefaultGateway

1.3.6.1.4.1.164.6.2.24

IpAddress

read-write

Default Gateway's IP Address.

systemPsTable

1.3.6.1.4.1.164.6.2.25

not-accessible

This table describes the PS types of a device. Usage of this table is specified in the device's NMS SRS

systemPsEntry

1.3.6.1.4.1.164.6.2.25.1

not-accessible

An entry in table.

I32 systemPsIndex1

1.3.6.1.4.1.164.6.2.25.1.1

Integer32

read-only

First Index. In HUBs: 1 = PS-A slot 2 = PS-B slot 3 = PS-C slot. In SA units: 1 = PS1 2 = PS2 Default = 1

I32 systemPsIndex2

1.3.6.1.4.1.164.6.2.25.1.2

Integer32

read-only

Second Index. In HUBs: 1 always. In SA units: 1 = Local 2 = Remote Default = 1.

INT systemPsType

1.3.6.1.4.1.164.6.2.25.1.3

INTEGER

read-only

The type of PS, for a stand-alone product. acDc - PS that supports both AC and DC. acPF - Power Feeding (phantom) box that is feeding another box by external AC. dcPF - Power Feeding (phantom) box that is feeding another box by external DC.

INT systemPsStatus

1.3.6.1.4.1.164.6.2.25.1.4

INTEGER

read-only

The Status of the PS unit.

INT systemPsHotSwap

1.3.6.1.4.1.164.6.2.25.1.5

INTEGER

read-only

Is PS unit hot swap or fixed.

OCT agnFans

1.3.6.1.4.1.164.6.2.26

OCTET STRING

read-only

This entry specifies the FANs existence and status. Each fan will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each fan: 00 - FAN does not exist 01 - FAN exists and OK (Low Mode) 10 - High Mode (FAN OK) 11 - FAN exists and is Failed bits 0-1 are for first fan bits 2-3 are for 2nd fan (if exists) bits 4-5 are for 3nd fan (if exists) bits 6-7 are for 4nd fan (if exists) bits 8-9 are for 5nd fan (if exists) bits 10-11 are for 6nd fan (if exists) bits 12-13 are for 7nd fan (if exists) bits 14-15 are for 8nd fan (if exists).

I32 agnSendTrapParameter

1.3.6.1.4.1.164.6.2.27

Integer32

read-write

This object specifies if the agent will attach a specific parameter to a trap. For ACE2002 the agent will attach or not the openViewSeverity parameter according to the value of this parameter: 1 - will attach openViewSeverity. 0 - will not attach openViewSeverity.

OCT agnSensorsStatus

1.3.6.1.4.1.164.6.2.28

OCTET STRING

read-only

This entry specifies the Sensors (Temperature sensors or others) existence and status. Each sensor will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each sensor: 00 - sensor does not exist 01 - sensor exists and status is OK 11 - sensor exists and status is not OK ( e.g. temperature exceeds pre-defined threshold) bits 0-1 are for first sensor bits 2-3 are for 2nd sensor (if exists) and so on... Bit 0 is the LSB.

INT agnStationClockCard

1.3.6.1.4.1.164.6.2.29

INTEGER

read-only

This entry specifies the station clock card existence and status. notExist - station clock card (piggy) does not exist. notValid - station clock card exists but clock status is not valid. ok - station clock card exists, and its status is OK When the sepcific reason for clock status not being valid is known, it may be reported by lossOfSync or lossOfSignal values.

I32 xcIndexNext

1.3.6.1.4.1.164.6.2.30

Integer32

read-only

This object contains an appropriate value to be used for xcIndex when creating entries in the xcTable. The value 0 indicates that no unassigned entries are available. To obtain the xcIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.

xcTable

1.3.6.1.4.1.164.6.2.31

not-accessible

Configuration of system cross-connect entries. The table follows the behavior described in RFC 2515, RFC 1604 regarding the creation deletion and modification of an entry within the table.

xcEntry

1.3.6.1.4.1.164.6.2.31.1

not-accessible

An entry in table.

I32 xcIndex

1.3.6.1.4.1.164.6.2.31.1.1

Integer32

not-accessible

Cross Connect Identifier.

I32 xcIfIndex1

1.3.6.1.4.1.164.6.2.31.1.2

Integer32

not-accessible

The interface Index from the ifTable, which identify one side of the connection.

I32 xcVpi

1.3.6.1.4.1.164.6.2.31.1.3

Integer32

not-accessible

The VPI value.

I32 xcVci

1.3.6.1.4.1.164.6.2.31.1.4

Integer32

not-accessible

The VCI value.

I32 xcIfIndex2

1.3.6.1.4.1.164.6.2.31.1.5

Integer32

not-accessible

The interface Index from the ifTable, which identifies the other side of the connection.

ROW xcRowStatus

1.3.6.1.4.1.164.6.2.31.1.6

RowStatus

read-create

This parameter allows NMS to create/delete entries of this table.

STR xcDescr

1.3.6.1.4.1.164.6.2.31.1.7

DisplayString

read-create

A textual string containing information about the xc entry.

INT xcAdminStatus

1.3.6.1.4.1.164.6.2.31.1.8

INTEGER

read-create

The desired administrative status of this bi-directional cross-connect.

INT xcOperStatus

1.3.6.1.4.1.164.6.2.31.1.9

INTEGER

read-only

The operational status of this bi-directional cross-connect.

INT xcAttachedIfType

1.3.6.1.4.1.164.6.2.31.1.10

INTEGER

read-only

This object indicates if the specific VCC is already attached to any interface, and indicates the type of the interface. This object's purpose is to ease the checking to the NMS. notApplicable - used for entries that are not LAN (as HDLC), or when the VCC was attached to a bridge, or when this parameter is irrelevant. free - the LAN VCC wasn't attached yet to any router interface. routerAtm - attached to an ATM router interface. lis - attached to a LIS interface.

I32 xcInputPriority

1.3.6.1.4.1.164.6.2.31.1.11

Integer32

read-create

This object is the priority, by which the LAN frames will be internaly sent to the ATM HW. This parameter is applicable if atmNteMdlInputPriorityMechanism=enabled. 1 - Highest priority. Will be the first to be sent to the ATM HW. 4 - Lowest priority. Will be the last to be sent to the ATM HW.

I32 xcBitMapping

1.3.6.1.4.1.164.6.2.31.1.12

Integer32

read-only

This object maps this entry to a bit of an octet string. For ACE2002 this object maps the LAN VCC to the bit of the VLAN Port Lists. If the value is '0' then it means that this VCC is not mapped to a port list or it may be an HDSL entry.

systemModule

1.3.6.1.4.1.164.6.2.32

modlParam

1.3.6.1.4.1.164.6.2.32.1

modlParamTable

1.3.6.1.4.1.164.6.2.32.1.1

not-accessible

This table include parameters for system modules.

modlParamEntry

1.3.6.1.4.1.164.6.2.32.1.1.1

not-accessible

An entry in table.

I32 modlParamIndex

1.3.6.1.4.1.164.6.2.32.1.1.1.1

Integer32

read-only

The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4.

INT modlParamReset

1.3.6.1.4.1.164.6.2.32.1.1.1.2

INTEGER

read-write

Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2).

INT modlParamSwdlStatus

1.3.6.1.4.1.164.6.2.32.1.1.1.3

INTEGER

read-only

This parameter indicates whatever the swdl is in process or not.

OCT modlParamLeds

1.3.6.1.4.1.164.6.2.32.1.1.1.4

OCTET STRING

read-only

This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.

INT modlParamType

1.3.6.1.4.1.164.6.2.32.1.1.1.5

INTEGER

read-only

This attribute indicates the Module Type.

STR modlParamSwVer

1.3.6.1.4.1.164.6.2.32.1.1.1.6

DisplayString

read-only

This attribute indicates the Module's Software Version.

INT agnNearFarConnection

1.3.6.1.4.1.164.6.2.33

INTEGER

read-only

This parameter describes the connection between near-end and far-end agents.

agnAccess

1.3.6.1.4.1.164.6.2.34

INT agnTelnetAccess

1.3.6.1.4.1.164.6.2.34.1

INTEGER

read-write

Enable/Disable accessing the device via Telnet. disable - no one will be allowed to access the device via Telnet. enable - all users are allowed Telnet Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSH) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSH).

INT agnWebAccess

1.3.6.1.4.1.164.6.2.34.2

INTEGER

read-write

Enable/Disable accessing the device via Web. disable - no one will be allowed to access the device via Web. enable - all users are allowed Web Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSL) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSL).

INT agnRadiusAccess

1.3.6.1.4.1.164.6.2.34.3

INTEGER

read-write

Enable/Disable authentication via RADIUS server.

INT agnSshAccess

1.3.6.1.4.1.164.6.2.34.4

INTEGER

read-write

Enable/Disable accessing the device via SSH. disable - no one will be allowed to access the device via SSH. enable - all users are allowed SSH Access. managersOnly - Only manager stations listed in the manager's list are allowed.

systemInterface

1.3.6.1.4.1.164.6.2.35

ifCreateTable

1.3.6.1.4.1.164.6.2.35.1

not-accessible

The Interface Configuration Table. This table enables to create interfaces of Entities.

ifCreateEntry

1.3.6.1.4.1.164.6.2.35.1.1

not-accessible

An entry in the Interface Configuration table.

SYS ifCreateEntityType

1.3.6.1.4.1.164.6.2.35.1.1.1

SysIfEntityType

read-only

This object indicates the Type of the Entity that exists above the created interface. For a Logical Port, this value can be: other (1) when there is no fixed entity above it.

I32 ifCreateEntityIdx

1.3.6.1.4.1.164.6.2.35.1.1.2

Integer32

read-only

This object indicates the Index of the Entity that exists above the created interface. For a Logical Port, this value can be: 9999 - N/A when there is no fixed entity above it.

I32 ifCreateNumber

1.3.6.1.4.1.164.6.2.35.1.1.3

Integer32

read-only

This object indicates the number of the Interface that is created.

ROW ifCreateRowStatus

1.3.6.1.4.1.164.6.2.35.1.1.4

RowStatus

read-create

This object enables the user to create/delete entries in this table.

IAN ifCreateType

1.3.6.1.4.1.164.6.2.35.1.1.5

IANAifType

read-create

This object indicates the Type of the Interface that is created.

I32 ifCreateIndex

1.3.6.1.4.1.164.6.2.35.1.1.6

Integer32

read-only

This object indicates the ifIndex of the created Interface. The ifIndex is assigned by the device.

I32 ifCreateConnectedTo

1.3.6.1.4.1.164.6.2.35.1.1.7

Integer32

read-create

This object indicates the entity connected to the created Interface. The value of this object can be ifIndex of the connected entity or any other number that can identify it.

U32 ifCreateParams

1.3.6.1.4.1.164.6.2.35.1.1.8

Unsigned32

read-create

This object represents one or more parameters of the created Interface. Each group of bits (one or more bits) represents a specific parameter and its possible values. This object's mapping and interpretation will be specified in each device's specification documents. The parameter should be used within the create PDU assuming atomic operation.

NUM ifCreateConnectionPointer

1.3.6.1.4.1.164.6.2.35.1.1.9

RowPointer

read-create

This parameter represents the entity that is connected to this Interface. It can be used instead of ifCreateConnectedTo. It is an OBJECT IDENTIFIER. This parameter's SYNTAX allows the following possibilities: - can be simply used for entity that is not an interface - is not limited to include up to 32 bits The value of this parameter is a pointer to an existing row of a table, where the entity connected to this Interface is defined (i.e. the pointer uniquely identifies the connected entity). Examples: In case of an interface (from 2863.ifTable): points to 'ifEntry' of corresponding row = . In case of a VPI/VCI (from 2515.atmVclTable): points to 'atmVclEntry' of corresponding row = ..VPI.VCI In case no entity is connected, value = 0 .

interfacePerformance

1.3.6.1.4.1.164.6.2.35.2

ifPerfTable

1.3.6.1.4.1.164.6.2.35.2.1

not-accessible

Interface Performance Table. The propose of this table is to support statistics counters having 64 bit by using 2 parameters with syntax= Integer32. This is because SNMPv1 does not support Counter64 properly. For SNMPv3, ifPerfHCCounter (Counter64) may be supported.

ifPerfEntry

1.3.6.1.4.1.164.6.2.35.2.1.1

not-accessible

An entry in the Interface Performance Table.

I32 ifPerfCounterType

1.3.6.1.4.1.164.6.2.35.2.1.1.1

Integer32

not-accessible

2nd index of the ifPerfTable. This parameter represents the Counter Type. Each application can have a different association between this object's value and counter type - see relevant application spec. For VPLS-MTU application use the following values: 1= Rx Octets, 2= Tx Octets, 3= Rx Frames, 4= Tx Frames, 5=Rx Dropped Frames, 6= Tx Dropped Frames. Optionally, counter type description appears in agnListDecodingTable

U32 ifPerfLowCounterPart

1.3.6.1.4.1.164.6.2.35.2.1.1.2

Unsigned32

read-only

In order to support Counters having 64 bit length, the performance counter is divided into two 32 bit parameters as follows: [ 64 bit parameter ] = [ High 32 bit parameter ][ Low 32 bit parameter ]. This parameter holds the Low 32 bits of the counter, while the following parameter holds the High 32 bits of the counter.

U32 ifPerfHighCounterPart

1.3.6.1.4.1.164.6.2.35.2.1.1.3

Unsigned32

read-only

This parameter holds the High 32 bits of the counter (see description in the above parameter).

C64 ifPerfHCCounter

1.3.6.1.4.1.164.6.2.35.2.1.1.4

Counter64

read-only

This High Capacity counter holds whole 64 bits of the counter indicated by ifPerfCounterType (concatenates both counter parts ifPerfHighCounterPart&ifPerfLowCounterPart) This object can be supported only by agents using SNMPv2 or SNMPv3.

systemOam

1.3.6.1.4.1.164.6.2.36

systemOamTable

1.3.6.1.4.1.164.6.2.36.1

not-accessible

The OAM Configuration Table.

systemOamEntry

1.3.6.1.4.1.164.6.2.36.1.1

not-accessible

An entry in the OAM table.

I32 systemOamCnfgIdx

1.3.6.1.4.1.164.6.2.36.1.1.1

Integer32

not-accessible

This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.

I32 systemOamFrequency

1.3.6.1.4.1.164.6.2.36.1.1.2

Integer32

read-write

Time in sec. between 2 OAM packets.

I32 systemOamTimeoutCycles

1.3.6.1.4.1.164.6.2.36.1.1.3

Integer32

read-write

No. of cycles the agent will send OAM packets without receiving a response from the remote device before declaring that the connection to the remote side is down - Time Out.

INT systemOamLinkCheck

1.3.6.1.4.1.164.6.2.36.1.1.4

INTEGER

read-write

This MIB object determines whether continuous connectivity Link checks will be performed by the device for uplinks. For Vmux-2100: enable (3) value can be set upon device installation. In this case, TDM Link Connectivity checks can be performed even before the user configures the Links of the device.If the value is enable (3) and there is no connection with the remote side, the Test LED will blink on the Main Board Module.

systemOamDescrTable

1.3.6.1.4.1.164.6.2.36.2

not-accessible

The OAM Descriptors Configuration Table.

systemOamDescrEntry

1.3.6.1.4.1.164.6.2.36.2.1

not-accessible

An entry in the OAM table.

I32 systemOamDescrIdx

1.3.6.1.4.1.164.6.2.36.2.1.1

Integer32

not-accessible

The OAM Descriptor Index.

ROW systemOamDescrRowStatus

1.3.6.1.4.1.164.6.2.36.2.1.2

RowStatus

read-create

Enables the user to create/delete entries in this table.

INT systemOamDescrMode

1.3.6.1.4.1.164.6.2.36.2.1.3

INTEGER

read-create

The OAM Mode of the Descriptor.

INT systemOamDescrCCDirection

1.3.6.1.4.1.164.6.2.36.2.1.4

INTEGER

read-create

OAM Continuity Check function mode. both(2) - Agent sends OAM CC cells and checks received OAM CC cells. none(3) - Agent does not send and does not check received OAM CC cells. source(4)- Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells.

INT systemOamDescrLoopbackOperation

1.3.6.1.4.1.164.6.2.36.2.1.5

INTEGER

read-create

The OAM Loopback function mode. off(2) - Stop sending loopback OAM cells. on(3) - Start loopback OAM cells.

OCT systemOamDescrLoopbackDestAddr

1.3.6.1.4.1.164.6.2.36.2.1.6

OCTET STRING

read-create

Loopback Destination Address.

G32 systemOamDescrXcCounter

1.3.6.1.4.1.164.6.2.36.2.1.7

Gauge32

read-only

The number of connections that use this OAM Descriptor.

INT agnDeviceView

1.3.6.1.4.1.164.6.2.37

INTEGER

read-only

This variable denotes the view of the device: Look: old look, new look or new look 2. Material: Plastic or Metal.

bitMappingTable

1.3.6.1.4.1.164.6.2.38

not-accessible

This table maps bits of an octet string to an interface. For ACE-2002 this table is used to map bits of VLAN port lists to LAN VCC's. This table is the opposite view of the xcTable for xcBitMapping. It is used to ease the bit translation for the NMS.

bitMappingEntry

1.3.6.1.4.1.164.6.2.38.1

not-accessible

Each entry in the table describes a correlation of a bit location to an interface. For ACE-2002 - Upon creation of a new LAN VCC the agent will add an entry to this table that will define the bit location for that VCC.

I32 bitMappingLocation

1.3.6.1.4.1.164.6.2.38.1.1

Integer32

not-accessible

The bit location in an octet string.

I32 bitMappingIndex

1.3.6.1.4.1.164.6.2.38.1.2

Integer32

read-only

The interface index or any other index that should be mapped.

OCT bitMappingView

1.3.6.1.4.1.164.6.2.39

OCTET STRING

read-only

A view of the bitMappingTable in one object - each entry in the biMappingTable will have the corresponding Bit of this object (bitMappingLocation) = '1'. For ACE-2002 it is used to describe all the existing LAN VCC's So that the NMS can easily calculate which VCC's can be selected as members for a VLAN, instead of reading all the bitMapping Table.

hostTable

1.3.6.1.4.1.164.6.2.40

not-accessible

Host interface table.

hostEntry

1.3.6.1.4.1.164.6.2.40.1

not-accessible

An entry in the Host Table. The hostParam1, hostParam2, and hostParam3 entries may have different use in different applications.

I32 hostIndex

1.3.6.1.4.1.164.6.2.40.1.1

Integer32

not-accessible

The Host Table Index. This index can have the same value as Host No.

IP hostIP

1.3.6.1.4.1.164.6.2.40.1.2

IpAddress

read-create

The host interface IP address.

IP hostIPMask

1.3.6.1.4.1.164.6.2.40.1.3

IpAddress

read-create

The host interface subnet mask.

IP hostDefaultNextHop

1.3.6.1.4.1.164.6.2.40.1.4

IpAddress

read-create

The host interface Default Next Hop address.

I32 hostMode

1.3.6.1.4.1.164.6.2.40.1.5

Integer32

read-create

This parameter represents the Host mode of operation. There can be different values for each application. For example: Not Applicable = 1.

I32 hostParam1

1.3.6.1.4.1.164.6.2.40.1.6

Integer32

read-create

This parameter represents the first Host parameter. There can be different values for each application. For example: Not Applicable = 1.

I32 hostParam2

1.3.6.1.4.1.164.6.2.40.1.7

Integer32

read-create

This parameter represents the 2nd Host parameter. There can be different values for each application.

I32 hostParam3

1.3.6.1.4.1.164.6.2.40.1.8

Integer32

read-create

This parameter represents the 3nd Host parameter. There can be different values for each application.

ROW hostRowStatus

1.3.6.1.4.1.164.6.2.40.1.9

RowStatus

read-create

Creation/Deletion of rows in the table.

INT hostVlanTagging

1.3.6.1.4.1.164.6.2.40.1.10

INTEGER

read-create

Host VLAN support (Tagging). untag - No support of VLAN Tagging. tag - 4 VLAN bytes will be added to the frame.

I32 hostVlanId

1.3.6.1.4.1.164.6.2.40.1.11

Integer32

read-create

Host VLAN ID.

I32 hostVlanPriority

1.3.6.1.4.1.164.6.2.40.1.12

Integer32

read-create

Host VLAN Frame priority.

invNameXCTable

1.3.6.1.4.1.164.6.2.41

not-accessible

Inverse Name XC Table. This table can be used to ease the search for a connection first index by the connection name.

invNameXCEntry

1.3.6.1.4.1.164.6.2.41.1

not-accessible

An entry in the table.

STR invNameXC

1.3.6.1.4.1.164.6.2.41.1.1

SnmpAdminString

not-accessible

The unique Connection name, associated to a Cross-Connection.

OID invNameXCType

1.3.6.1.4.1.164.6.2.41.1.2

OBJECT IDENTIFIER

read-only

The OBJECT IDENTIFIER of the respective XC Table. Examples: XC Table invNameXCType --------------------------------------------------- atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .

I32 invNameXCIndex

1.3.6.1.4.1.164.6.2.41.1.3

Integer32

read-only

The XC Table (invNameXCType) may include more than one index. This object represents the value of the first XC Index.

OCT agnDeviceCapabilities

1.3.6.1.4.1.164.6.2.42

OCTET STRING

read-only

Indicates the optional capabilities that are implemented by this device and are manageable through this MIB. For each capability 1 BIT is allocated in each Octet starting from the LSB. If the value of the BIT = 1, the capability is Enabled. If the value of the BIT = 0, the capability is Disabled. For bit assignment, refer to device specification. Capabilities example: Router - BIT 0 (0000 0001 = 01 Hex = 1 Decimal). The 2nd octet (MSB) will represent the maximum number of intervals that the Agent can keep in its DB (same for all ports). For Vmux, this object describes agent's support of LBRAD coder feature: 1 octet ; bit 0 (LSB). '1' - LBRAD feature is supported '0' - LBRAD feature is not supported.

rowInfoTable

1.3.6.1.4.1.164.6.2.43

not-accessible

This table holds information of other tables.

rowInfoEntry

1.3.6.1.4.1.164.6.2.43.1

not-accessible

An entry in the table.

OID rowInfoTableId

1.3.6.1.4.1.164.6.2.43.1.1

OBJECT IDENTIFIER

not-accessible

The OBJECT IDENTIFIER of the Table, which its information is held by this table (rowInfoTable). Examples: Table Name rowInfoTableId --------------------------------------------------- atmTrafficDescrParamTable 1.3.6.1.2.1.37.1.5 atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .

I32 rowInfoCounter

1.3.6.1.4.1.164.6.2.43.1.2

Integer32

read-only

The Number of rows in the table, indicated by rowInfoTableId.

I32 rowInfoIndexNext

1.3.6.1.4.1.164.6.2.43.1.3

Integer32

read-only

The First Free Index of the table, indicated by rowInfoTableId.

I32 rowInfoMaxNoOfRows

1.3.6.1.4.1.164.6.2.43.1.4

Integer32

read-only

The maximum possible number of rows in the table, indicated by rowInfoTableId.

INT agnStoreCmd

1.3.6.1.4.1.164.6.2.44

INTEGER

read-write

Store command. inFlash(3) = store the current Agent configuration in Flash memory. asDefConfigFile(4) = store the current Agent configuration as Default Configuration file (e.g. 'DefConfig.cfg'). Agent will perform the required command and change automatically the value of this object to off(2).

agnFunctionTable

1.3.6.1.4.1.164.6.2.45

not-accessible

This table is used in order to activate/deactivate device functions. The index indicates the function. Each function can be Enabled or Disabled.

agnFunctionEntry

1.3.6.1.4.1.164.6.2.45.1

not-accessible

An entry in the table.

INT agnFunction

1.3.6.1.4.1.164.6.2.45.1.1

INTEGER

not-accessible

This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock.

INT agnFunctionActivation

1.3.6.1.4.1.164.6.2.45.1.2

INTEGER

read-write

This MIB object indicates the activation of the current function.

I32 agnManagerConfigPorts

1.3.6.1.4.1.164.6.2.46

Integer32

read-write

This variable defines from which port/s this manager can manage the device. The value is a sum of 2**n, where n is a bit assigned to a certain port. For RIC-E1 and ETX 102 the value will be according to the ports combination: Network = bit 0 User= bit 1 For Example: All = 3.

INT agnEgressRateRange

1.3.6.1.4.1.164.6.2.47

INTEGER

read-write

This variable defines the valid ranges of egress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.

I32 agnNoOfCurrentConnsEx

1.3.6.1.4.1.164.6.2.48

Integer32

read-only

This variable indicates the number of connections currently configured for the agent.

INT agnIngressRateRange

1.3.6.1.4.1.164.6.2.49

INTEGER

read-write

This variable defines the valid ranges of ingress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.

alarmForwardingTable

1.3.6.1.4.1.164.6.2.50

not-accessible

The Alarm Forwarding Mechanism will be operated for this table entries.

alarmForwardingEntry

1.3.6.1.4.1.164.6.2.50.1

not-accessible

Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.

I32 alarmForwardingFailPort

1.3.6.1.4.1.164.6.2.50.1.1

Integer32

not-accessible

An Index of the port on which a fail occurs.

I32 alarmForwardingToPort

1.3.6.1.4.1.164.6.2.50.1.2

Integer32

not-accessible

An Index of the port that will be affected upon the failure of the alarmForwardingFailPort.

ROW alarmForwardingRowStatus

1.3.6.1.4.1.164.6.2.50.1.3

RowStatus

read-create

Creation/ Deletion of rows in the table.

I32 alarmForwardingRecoveryTime

1.3.6.1.4.1.164.6.2.50.1.4

Integer32

read-create

This parameter defines the maximum time (sec) the affected port will hold the down state.

I32 alarmForwardingGroupConditions

1.3.6.1.4.1.164.6.2.50.1.5

Integer32

read-create

This parameter is applicable when there is a group of interfaces in which a fault may occur, and one interface to which alarm is propagated (forwarded). 0 = All - Forwarding will take place only when all interfaces of the same group are faulty. 1 = Single - Forwarding will take place when at least one (single) interface of the same group (any of them) is faulty. n - forwarding will take place only when n (n < all) interfaces of the same group fail.

BIT alarmForwardingCause

1.3.6.1.4.1.164.6.2.50.1.6

Bits

read-create

Bit map representing the cause upon which alarm forwarding will take place. bit 0 - LOSS (LINE DOWN) bit 1 - AIS bit 2 - RDI bit 3 - PROTOCOL DOWN.

INT alarmForwardingRecoveryMode

1.3.6.1.4.1.164.6.2.50.1.7

INTEGER

read-create

This parameter determines the Recovery Mode. manual - The user should stop the alarm forwarding by using the alarmForwardingRecoveryCommand. automatic - Alarm forwarding will be automatically stopped upon alarmForwardingFailPort recovery.

INT alarmForwardingRecoveryCommand

1.3.6.1.4.1.164.6.2.50.1.8

INTEGER

read-create

This parameter is a command. It is applicable when alarmForwardingRecoveryMode = manual. on - Will stop alarm forwarding. After setting to 'On', the agent will set this parameter back to 'Off'.

U32 alarmForwardingDelay

1.3.6.1.4.1.164.6.2.50.1.9

Unsigned32

read-create

This parameter determines the period of time (in seconds) the alarm of the alarmForwardingFailPort should exist before starting alarm forwarding.

INT alarmForwardingDirection

1.3.6.1.4.1.164.6.2.50.1.10

INTEGER

read-create

This parameter determines the Direction of the Alarm Forwarding. unidirectional - alarmForwardingFailPort affects the alarmForwardingToPort. bidirectional - alarmForwardingFailPort affects the alarmForwardingToPort AND vice-versa. For such cases, this value will be selected, instead of entering an additional unidirectional entry in the table, where the indexes are swapped.

BIT alarmForwardingAction

1.3.6.1.4.1.164.6.2.50.1.11

Bits

read-create

Bit map representing the action to be performed when alarm forwarding will take place. bit 0 - No Action. '1' value - device should NOT perform any action, though other bits indicate the action to be taken. '0' value - device should perform the action/s indicated by rest of the bits. In this case, one of the other bits should be '1'. bit 1 - Interface Deactivation (of the affected Port: alarmForwardingToPort) bit 2 - OAM Signaling. Affected Port (alarmForwardingToPort) will send special OAM Signaling to the Far-End unit about the Failure. This object will be used only for devices that support Deactivation per entry OR can support more than one action.

INT agnSwVersionSwapCmd

1.3.6.1.4.1.164.6.2.51

INTEGER

read-write

SW switch command. mainAndBackup (3) = Swap between Main SW and the backup one. Agent will perform the required command and change automatically the value of this object to off(2).

agnClockSource

1.3.6.1.4.1.164.6.2.52

agnClkSrcPortTable

1.3.6.1.4.1.164.6.2.52.1

not-accessible

Pool of Ports for the Master/Fallback Clock Source and of Recovered IDs. For devices with more than one configuration: Set operation is valid only to the TmpCnfg entry.

agnClkSrcPortEntry

1.3.6.1.4.1.164.6.2.52.1.1

not-accessible

An entry in the table.

I32 agnClkSrcPortCnfgIdx

1.3.6.1.4.1.164.6.2.52.1.1.1

Integer32

not-accessible

This object indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. For product supporting a single configuration, the value will be 1.

INT agnClkSrcPortSrcIdx

1.3.6.1.4.1.164.6.2.52.1.1.2

INTEGER

not-accessible

Clock Source Index. master - refers to Master clock fallback - refers to Fallback clock recovered - refers to Recovered clock.

I32 agnClkSrcPortIdx

1.3.6.1.4.1.164.6.2.52.1.1.3

Integer32

not-accessible

This object indicates the running Idx of the port that is to be used as Clock Source, for each agnClkSrcPortSrcIdx instance. In case of Recovered Clock - it indicates the Clock ID.

I32 agnClkSrcPort

1.3.6.1.4.1.164.6.2.52.1.1.4

Integer32

read-create

This object indicates the Port/Interface Index of the port that is to be used as Clock Source. In case of Recovered Clock - it indicates the PW number.

ROW agnClkSrcPortRowStatus

1.3.6.1.4.1.164.6.2.52.1.1.5

RowStatus

read-create

This object enables Creation/ Deletion of rows in the table.

INT agnClkSrcPortAdminStatus

1.3.6.1.4.1.164.6.2.52.1.1.6

INTEGER

read-create

This object indicates the Recovered Clock Administrative Status.

INT agnClkSrcPortType

1.3.6.1.4.1.164.6.2.52.1.1.7

INTEGER

read-create

This object is relevant only in case of Recovery Clock. It indicates the Clock Type.

INT agnClkSrcPortQuality

1.3.6.1.4.1.164.6.2.52.1.1.8

INTEGER

read-create

This object indicates the Clock Source Quality.

INT agnClkSrcPortNetType

1.3.6.1.4.1.164.6.2.52.1.1.9

INTEGER

read-create

This object is relevant only in case of Recovery Clock. It indicates the Clock Network Type, i.e. the PSN network characteristics and behavior.

INT agnClkSrcPortState

1.3.6.1.4.1.164.6.2.52.1.1.10

INTEGER

read-only

This object indicates the Clock State. freeRun(1) - Clock recovery is not locked to any clock. frequencyAcquisition(2) - Adaptive clock recovery is learning the frequency. rapidPhaseLock(3) - Clock recovery is in training process till it reaches fine phase lock. finePhaseLock(4) - Clock is locked and clock recovery is qualified and stable. holdover(5) - Clock recovery is in holdover mode. notApplicable(6) - Clock recovery is not applicable. .

agnCurrClkTable

1.3.6.1.4.1.164.6.2.52.2

not-accessible

Current Clock Source.

agnCurrClkEntry

1.3.6.1.4.1.164.6.2.52.2.1

not-accessible

An entry in the table.

I32 agnCurrClkObjIdx

1.3.6.1.4.1.164.6.2.52.2.1.1

Integer32

not-accessible

This MIB object identifies the object for which the Clock Source is used (System, Other System, Card).

INT agnCurrClkMode

1.3.6.1.4.1.164.6.2.52.2.1.2

INTEGER

read-only

Current Clock Source Mode. master - refers Master clock fallback - refers Fallback clock internal - only when both Master and Fallback Sources failed

INT agnCurrClkSrc

1.3.6.1.4.1.164.6.2.52.2.1.3

INTEGER

read-only

This object indicates the Current Clock Source.

I32 agnCurrClkPort

1.3.6.1.4.1.164.6.2.52.2.1.4

Integer32

read-only

This object indicates the Port/Interface Index of the port that is Currently used as Clock Source.

INT agnCurrClkHoldover

1.3.6.1.4.1.164.6.2.52.2.1.5

INTEGER

read-only

Current Clock Holdover State. As a last resort, in the absence of higher quality timing: - a SONET/SDH object can enter 'holdover' state, until higher quality external timing becomes available again. In this state (value=yes) the SONET/SDH object uses its own timing circuits for clock of the SONET/SDH signal. - for other objects, the 'holdover'=yes state means that the object uses last available clock (stored by the object) for a pre-defined time, until another clock source is used.

INT agnCurrClkSsmBased

1.3.6.1.4.1.164.6.2.52.2.1.6

INTEGER

read-only

This parameter indicates whether clock source is selected based on receive clock quality. Clock quality is indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging).

INT agnCurrClkState

1.3.6.1.4.1.164.6.2.52.2.1.7

INTEGER

read-only

This object indicates the Current Clock State. freeRun(1) - Current clock state machine is not locked and run from the internal oscillator. rapidPhaseLock(2) - Current clock state machine is locked. finePhaseLock(3) - Current clock state machine is in pre-locking. holdover(4) - Current clock state machine is in holdover mode (due to loss of event). .

INT agnCurrClkQualification

1.3.6.1.4.1.164.6.2.52.2.1.8

INTEGER

read-only

This object indicates the Current Clock Qualification and defines whether the PLL can locked according to the stratum definitions.

agnClockMonitoring

1.3.6.1.4.1.164.6.2.52.3

agnClkCurrentTable

1.3.6.1.4.1.164.6.2.52.3.1

not-accessible

The Clock Current table.

agnClkCurrentEntry

1.3.6.1.4.1.164.6.2.52.3.1.1

not-accessible

An entry in the Clock Current table.

U32 agnClkCurrentIndex

1.3.6.1.4.1.164.6.2.52.3.1.1.1

Unsigned32

not-accessible

An Index that is uniquely represents the Clock.

G32 agnClkCurrentRxPackets

1.3.6.1.4.1.164.6.2.52.3.1.1.2

Gauge32

read-only

The counter associated with the number of Received Packets, encountered by a Bridge Port in the current 15 minute interval.

G32 agnClkCurrentLostPackets

1.3.6.1.4.1.164.6.2.52.3.1.1.3

Gauge32

read-only

The counter associated with the number of Lost Packets, encountered by a Bridge Port in the current 15 minute interval.

G32 agnClkCurrentOutOfOrderPackets

1.3.6.1.4.1.164.6.2.52.3.1.1.4

Gauge32

read-only

The counter associated with the number of times Out-of-Order Packets encountered by a Bridge Port in the current 15 minute interval.

G32 agnClkCurrentBufferUnderflow

1.3.6.1.4.1.164.6.2.52.3.1.1.5

Gauge32

read-only

The counter associated with the number of times Underflow event encountered by a Bridge Port in the current 15 minute interval.

agnClkIntervalTable

1.3.6.1.4.1.164.6.2.52.3.2

not-accessible

The Clock Interval table.

agnClkIntervalEntry

1.3.6.1.4.1.164.6.2.52.3.2.1

not-accessible

An entry in the Clock Interval table.

U32 agnClkIntervalIndex

1.3.6.1.4.1.164.6.2.52.3.2.1.1

Unsigned32

not-accessible

An Index that is uniquely represents the Clock.

U32 agnClkIntervalNumber

1.3.6.1.4.1.164.6.2.52.3.2.1.2

Unsigned32

not-accessible

A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).

G32 agnClkIntervalRxPackets

1.3.6.1.4.1.164.6.2.52.3.2.1.3

Gauge32

read-only

The counter associated with the number of Received Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.

G32 agnClkIntervalLostPackets

1.3.6.1.4.1.164.6.2.52.3.2.1.4

Gauge32

read-only

The counter associated with the number of Lost Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.

G32 agnClkIntervalOutOfOrderPackets

1.3.6.1.4.1.164.6.2.52.3.2.1.5

Gauge32

read-only

The counter associated with the number of times Out-of-Order Packets are detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.

G32 agnClkIntervalBufferUnderflow

1.3.6.1.4.1.164.6.2.52.3.2.1.6

Gauge32

read-only

The counter associated with the number of times Underflow event is detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.

I32 agnMaxNoOfConns

1.3.6.1.4.1.164.6.2.53

Integer32

read-only

This variable indicates the maximum number of connections that can be configured for the agent.

lag

1.3.6.1.4.1.164.6.2.54

lagTable

1.3.6.1.4.1.164.6.2.54.1

not-accessible

A table defining Link Aggregation Groups port association, and other parameters.

lagEntry

1.3.6.1.4.1.164.6.2.54.1.1

not-accessible

An entry in the LAG table.

U32 lagCnfgIdx

1.3.6.1.4.1.164.6.2.54.1.1.1

Unsigned32

not-accessible

This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.

U32 lagIdx

1.3.6.1.4.1.164.6.2.54.1.1.2

Unsigned32

not-accessible

This object indicates LAG unique index.

POR lagPortMembers

1.3.6.1.4.1.164.6.2.54.1.1.3

PortList

read-create

The set of ports which are permanently assigned to the Link Aggregation Group. The default value of this object is a string of zeros.

INT lagDistributionMethod

1.3.6.1.4.1.164.6.2.54.1.1.4

INTEGER

read-create

This object defines the criteria for the 802.3ad (LAG) to split the traffic between ports

INT lagRecoveryMode

1.3.6.1.4.1.164.6.2.54.1.1.5

INTEGER

read-create

This object defines whether traffic will be returned to a port after its recovery. This object is applicable only when lagDistributionMethod= oneToOne (3).

U32 lagWaitToRestore

1.3.6.1.4.1.164.6.2.54.1.1.6

Unsigned32

read-create

This object defines traffic recovery time (in seconds) to the port after its recovery. This object is applicable only when lagRecoveryMode= revertive (3).

ROW lagRowStatus

1.3.6.1.4.1.164.6.2.54.1.1.7

RowStatus

read-create

This object enables user to create/delete entries of this table. Note: When using LAG standard package, this table is static, hence, only the values active(1), notInService(2) are used.

U32 lagShutDownDurationUponFlip

1.3.6.1.4.1.164.6.2.54.1.1.8

Unsigned32

read-create

This object defines the duration (in seconds) the active port transmission is shut down after LAG Flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0=no shut-down. This object is applicable only when lagDistributionMethod=oneToOne(3) and mainly when each of the Links of our device is connected to a different device.

INT lagRdnMethod

1.3.6.1.4.1.164.6.2.54.1.1.9

INTEGER

read-create

This object defines the redundancy method.

INT lagLacpEnable

1.3.6.1.4.1.164.6.2.54.1.1.10

INTEGER

read-create

Enabling/Disabling the LACP for a LAG. The LACP will be enabled for all ports belonging to this LAG.

lagStatTable

1.3.6.1.4.1.164.6.2.54.2

not-accessible

A table defining Link Aggregation Groups Redundancy. This table is applicable only when lagDistributionMethod = oneToOne.

lagStatEntry

1.3.6.1.4.1.164.6.2.54.2.1

not-accessible

An entry in the LAG Status table.

U32 lagStatForcePort

1.3.6.1.4.1.164.6.2.54.2.1.1

Unsigned32

read-write

This object enables user to enforce the active port. 0 = No Enforcement; Otherwise the ifIndex of the port.

U32 lagStatActivePort

1.3.6.1.4.1.164.6.2.54.2.1.2

Unsigned32

read-only

This object indicates the current active port. It is applicable only when lagDistributionMethod = oneToOne. The value is the ifIndex of the port. 0 = none of the ports is active.

gfp

1.3.6.1.4.1.164.6.2.55

gfpCnfgTable

1.3.6.1.4.1.164.6.2.55.1

not-accessible

Configuration table for GFP (General Framing Protocol).

gfpCnfgEntry

1.3.6.1.4.1.164.6.2.55.1.1

not-accessible

An entry in the GFP configuration table.

U32 gfpCnfgIdx

1.3.6.1.4.1.164.6.2.55.1.1.1

Unsigned32

not-accessible

Index to GFP configuration table.

INT gfpPayloadFcs

1.3.6.1.4.1.164.6.2.55.1.1.2

INTEGER

read-write

This object defines whether protocol header will include FCS.

INT gfpRxTxScramble

1.3.6.1.4.1.164.6.2.55.1.1.3

INTEGER

read-write

This object defines whether transmission will be scrambled.

INT gfpVcatHeader

1.3.6.1.4.1.164.6.2.55.1.1.4

INTEGER

read-write

VCAT header is LCAS CONTROL packet as described in the G-7043. one control packet is transmitted in a period of 16 Multi frame

agnGroupTable

1.3.6.1.4.1.164.6.2.56

not-accessible

A table that enables associating components to Group/s (or removing components of a group). The Group Idx can then be used in other tables (e.g alarmForwardingTable).

agnGroupEntry

1.3.6.1.4.1.164.6.2.56.1

not-accessible

An entry in the agnGroupTable.

U32 agnGroupCnfgIdx

1.3.6.1.4.1.164.6.2.56.1.1

Unsigned32

not-accessible

This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.

U32 agnGroupIdx

1.3.6.1.4.1.164.6.2.56.1.2

Unsigned32

not-accessible

This object indicates a unique Group Index.

U32 agnGroupComponentIdx

1.3.6.1.4.1.164.6.2.56.1.3

Unsigned32

not-accessible

This object indicates a unique Component Index that belongs to the Group defined by agnGroupIdx.

ROW agnGroupRowStatus

1.3.6.1.4.1.164.6.2.56.1.4

RowStatus

read-create

This object enables user to create/delete entries of this table. destroy - If a Group is used in another table, Agent may not allow destroying the entry/ies that belong to this Group Index.

I32 agnStatNoOfUploadedIntervalsEx

1.3.6.1.4.1.164.6.2.57

Integer32

read-only

This parameter indicates the Number of Intervals that were successfully collected and uploaded in the last statistics collection session.

agnSyslog

1.3.6.1.4.1.164.6.2.58

U32 agnSyslogDeviceUdpPort

1.3.6.1.4.1.164.6.2.58.1

Unsigned32

read-write

The UDP Port of the device, from which Syslog messages are sent. Default=514.

INT agnSyslogFacility

1.3.6.1.4.1.164.6.2.58.2

INTEGER

read-write

A user defined SW module, task or function, from which Syslog messages are sent to the remote Server.

INT agnSyslogSeverityLevel

1.3.6.1.4.1.164.6.2.58.3

INTEGER

read-write

Device will send events equal or exceeding this severity level (configured by user).

INT agnNetworkInterfaceType

1.3.6.1.4.1.164.6.2.59

INTEGER

read-write

This MIB object indicates the network interface type to be used by the device. It is used for devices that use only one network port type.

U32 agnTrapDelay

1.3.6.1.4.1.164.6.2.60

Unsigned32

read-write

This variable enables the user to set a delay (in seconds) before a trap is sent. This delay will be used only for traps that need to be sent during device initialization. It is needed because the device connected to our device starts transmitting traps later. The delay starts from the end of the Boot process. The device will keep the init traps in the correct order, and cancel those which clear former ones in the list. After this init delay, traps will be sent without a delay.

agnStringToIndexTable

1.3.6.1.4.1.164.6.2.62

not-accessible

This table holds the conversions of tables from unique String to numeric index.

agnStringToIndexEntry

1.3.6.1.4.1.164.6.2.62.1

not-accessible

An entry in the table.

OID agnStringToIndexTableId

1.3.6.1.4.1.164.6.2.62.1.1

OBJECT IDENTIFIER

not-accessible

The OBJECT IDENTIFIER of the Table, having as index numeric values. In this table, the value of agnStringToIndexUserName is an attribute.

STR agnStringToIndexUserName

1.3.6.1.4.1.164.6.2.62.1.2

SnmpAdminString

not-accessible

This object indicates a unique name used by agnStringToIndexTableId, although it is not it's index.

U32 agnStringToIndexTableIndex

1.3.6.1.4.1.164.6.2.62.1.3

Unsigned32

read-only

The numeric Index of agnStringToIndexTableId.

agnRowPointerTable

1.3.6.1.4.1.164.6.2.63

not-accessible

This table holds information about a specific entry in a table. For example, number of usages of this row.

agnRowPointerEntry

1.3.6.1.4.1.164.6.2.63.1

not-accessible

An entry in the table.

OID agnRowPointerIndex

1.3.6.1.4.1.164.6.2.63.1.1

OBJECT IDENTIFIER

not-accessible

The OBJECT IDENTIFIER of an entry in a table.

U32 agnRowPointerNoOfUsages

1.3.6.1.4.1.164.6.2.63.1.2

Unsigned32

read-only

The number of usages of specific entry in a table, which is pointed by agnRowPointerIndex.Usually, when the value of this counter is greater than 0,the entry cannot be removed.

services

1.3.6.1.4.1.164.6.3

wfq

1.3.6.1.4.1.164.6.3.1

wfqTable

1.3.6.1.4.1.164.6.3.1.1

not-accessible

This table allows user to define several WFQ tables per output port. WFQ supports flows with different bandwidth requirements by giving each queue a weight that assigns it a different percentage of output port bandwidth. When Weighted Fair Queuing is used, it is possible to precisely attribute bandwidth partitioning among the queues. When there is congestion, each class (queue) is not allowed to use more bandwidth than the amount allocated to it.

wfqEntry

1.3.6.1.4.1.164.6.3.1.1.1

not-accessible

An entry in the Weighted Fair Queueing table.

I32 wfqCnfgIdx

1.3.6.1.4.1.164.6.3.1.1.1.1

Integer32

not-accessible

This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.

I32 wfqPrtIdx

1.3.6.1.4.1.164.6.3.1.1.1.2

Integer32

not-accessible

This object indicates a unique port or interface number, for which Weighted Fair Queueing table is applicable . For numbering, see product's spec. For some products, the numbering can equal ifIndex. Value of 255 (not applicable) refer to system level queue

I32 wfqTblIdx

1.3.6.1.4.1.164.6.3.1.1.1.3

Integer32

not-accessible

This object indicates which Weighted Fair Queueing (WFQ) Table is being used. There can be several tables. For FCD-155 User will select which one will be used for a virtual concatenation group.Valid values are 1,2

I32 wfqQueueIdx

1.3.6.1.4.1.164.6.3.1.1.1.4

Integer32

not-accessible

This object indicates a queue index. For FCD-155, valid queues are 1..3. The 4th queue is not in MIB. Its weight will be RO, Calculated according to the sum of the 3 first queues.

ROW wfqRowStatus

1.3.6.1.4.1.164.6.3.1.1.1.5

RowStatus

read-create

This object enables Creation/Deletion of rows in the WFQ table. For FCD-155, rows are not created nor destroyed by user.

I32 wfqWeightValue

1.3.6.1.4.1.164.6.3.1.1.1.6

Integer32

read-create

This object indicates a relative weight value. User should make sure that the sum of values for all queues will not exceed 100% (sum should be BELOW 100% in order to leave some BW percentage for last queue) Note that when this attribute is being used, the wfqMinRateAbsolute attribute is NA.

INT wfqSchedulingMode

1.3.6.1.4.1.164.6.3.1.1.1.7

INTEGER

read-create

This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme or priority Queue (Strict Priority).

U32 wfqMinRateAbsolute

1.3.6.1.4.1.164.6.3.1.1.1.8

Unsigned32

read-create

The minimum absolute rate, in kbps, that should be allocated to this queue. If the value is zero, then there is effectively no minimum rate guarantee. If the value is non-zero, then the servicing of this queue in at least this rate is assured. Note that when this attribute is being used, the wfqWeightValue attribute is NA.

U32 wfqMaxPacketSize

1.3.6.1.4.1.164.6.3.1.1.1.9

Unsigned32

read-create

The size of the largest packet which can be received on this queue, specified in octets. Packets larger than this size will be discarded.

dscpMapping

1.3.6.1.4.1.164.6.3.2

dscpMappingTable

1.3.6.1.4.1.164.6.3.2.1

not-accessible

Mapping of DSCP value to a regenerated priority level.

dscpMappingEntry

1.3.6.1.4.1.164.6.3.2.1.1

not-accessible

An entry in dscpMappingTable.

I32 dscpMappingCnfgIdx

1.3.6.1.4.1.164.6.3.2.1.1.1

Integer32

not-accessible

This object indicates the Idx of the Agent Cnfg the following objects refer to. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.

DSC dscpMappingDscpIdx

1.3.6.1.4.1.164.6.3.2.1.1.2

Dscp

not-accessible

DSCP value of the incoming IP packet

I32 dscpMappingRegenPriority

1.3.6.1.4.1.164.6.3.2.1.1.3

Integer32

read-write

The Regenerated Priority level the incoming DSCP value is mapped to. For FCD-155, valid values are 0,1,2,3

ifTeQos

1.3.6.1.4.1.164.6.3.3

ifTeQosTable

1.3.6.1.4.1.164.6.3.3.1

not-accessible

The TE QOS Interface Table.

ifTeQosEntry

1.3.6.1.4.1.164.6.3.3.1.1

not-accessible

An entry in the TE QOS Interface table.

I32 ifTeQosIdx1

1.3.6.1.4.1.164.6.3.3.1.1.1

Integer32

not-accessible

This object indicates the 1st Index of the table.

I32 ifTeQosIdx2

1.3.6.1.4.1.164.6.3.3.1.1.2

Integer32

not-accessible

This object indicates the 2nd Index of the table.

I32 ifTeQosIdx3

1.3.6.1.4.1.164.6.3.3.1.1.3

Integer32

not-accessible

This object indicates the 3rd Index of the table.

OCT ifTeQosParam

1.3.6.1.4.1.164.6.3.3.1.1.4

OCTET STRING

read-write

This object is used for QOS attributes of the entry's entities.

OCT ifTeQosParam2

1.3.6.1.4.1.164.6.3.3.1.1.5

OCTET STRING

read-write

This object is used for 2nd group QOS attributes of the entry's entities.

INT ifTeQosStatus

1.3.6.1.4.1.164.6.3.3.1.1.6

INTEGER

read-write

This object is used to create, activate and destroy entries of this table.

portQos

1.3.6.1.4.1.164.6.3.4

prtPriorityTable

1.3.6.1.4.1.164.6.3.4.1

not-accessible

A table - Parameters per port per Priority .

prtPriorityEntry

1.3.6.1.4.1.164.6.3.4.1.1

not-accessible

An entry in table.

I32 prtPriorityIdx1

1.3.6.1.4.1.164.6.3.4.1.1.1

Integer32

not-accessible

This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. or any other Index.

I32 prtPriorityPrtIdx

1.3.6.1.4.1.164.6.3.4.1.1.2

Integer32

not-accessible

This object indicates a unique Port Index. Refer to device specification for port Index.

I32 prtPriorityIdx

1.3.6.1.4.1.164.6.3.4.1.1.3

Integer32

not-accessible

This object indicates the Traffic Priority Index.

I32 prtPriorityIngressRateLimit

1.3.6.1.4.1.164.6.3.4.1.1.4

Integer32

read-write

The maximum rate permitted at Ingress of this port with this Traffic Priority, in Kbps.

prtQosTable

1.3.6.1.4.1.164.6.3.4.2

not-accessible

Port QoS (Quality of Service) table.

prtQosEntry

1.3.6.1.4.1.164.6.3.4.2.1

not-accessible

An entry in table.

U32 prtQosIdx

1.3.6.1.4.1.164.6.3.4.2.1.1

Unsigned32

not-accessible

The first index of the table. This attribute might indicate the Idx of the Cnfg (1..255) being accessed ; Idx of 255 relates to the TmpCnfg or any other Index.

U32 prtQosPrtIdx

1.3.6.1.4.1.164.6.3.4.2.1.2

Unsigned32

not-accessible

This object indicates a unique Port Index. Refer to device specification for port Index.

INT prtQosDirection

1.3.6.1.4.1.164.6.3.4.2.1.3

INTEGER

not-accessible

This object indicates the port's QoS Direction.

INT prtQosRateLimitPacketType

1.3.6.1.4.1.164.6.3.4.2.1.4

INTEGER

read-write

This object indicates the Type of Packets on which Rate Limitation is applied.

U32 prtQosRateLimitCIR

1.3.6.1.4.1.164.6.3.4.2.1.5

Unsigned32

read-write

This object indicates the port's CIR (Committed Information Rate) in Kbps. Value=0 represents best effort.

U32 prtQosRateLimitCBS

1.3.6.1.4.1.164.6.3.4.2.1.6

Unsigned32

read-write

This object indicates the port's CBS (Committed Burst Size) in KB. Value=0 represents best effort.

U32 prtQosRateLimitEIR

1.3.6.1.4.1.164.6.3.4.2.1.7

Unsigned32

read-write

This object indicates the port's EIR (Excess Information Rate) in Kbps.

U32 prtQosRateLimitEBS

1.3.6.1.4.1.164.6.3.4.2.1.8

Unsigned32

read-write

This object indicates the port's EBS (Excess Burst Size) in KB.

prtTrafficClass

1.3.6.1.4.1.164.6.3.5

portTrafficClassTable

1.3.6.1.4.1.164.6.3.5.1

not-accessible

Mapping of port to Traffic Class level.

portTrafficClassEntry

1.3.6.1.4.1.164.6.3.5.1.1

not-accessible

An entry in portTrafficClassTable.

I32 portTrafficClassIdx1

1.3.6.1.4.1.164.6.3.5.1.1.1

Integer32

not-accessible

This attribute indicates the 1st index of the table. This may be the Idx of the Cnfg(1..255) being accessed; Idx of 255 relates to the TmpCnfg, or any other Index.

I32 portTrafficClassPortIdx

1.3.6.1.4.1.164.6.3.5.1.1.2

Integer32

not-accessible

This object indicates a unique Port Index. Refer to device specification for port Index.

I32 portTrafficClass

1.3.6.1.4.1.164.6.3.5.1.1.3

Integer32

read-write

This object indicates the Traffic Class level of this port.

serviceTable

1.3.6.1.4.1.164.6.3.6

not-accessible

Table of services.

serviceEntry

1.3.6.1.4.1.164.6.3.6.1

not-accessible

An entry in the Service Table.

U32 flowIndex

1.3.6.1.4.1.164.6.3.6.1.1

Unsigned32

not-accessible

Defines the Flow ID the service is associated to.

U32 serviceIndex

1.3.6.1.4.1.164.6.3.6.1.2

Unsigned32

not-accessible

Defines the Service ID - according to the CoS.

ROW serviceRowStatus

1.3.6.1.4.1.164.6.3.6.1.3

RowStatus

read-create

This attribute is used to create a new row or to delete an existing row in the table.

STR serviceName

1.3.6.1.4.1.164.6.3.6.1.4

SnmpAdminString

read-create

This attribute defines the service name.

U32 serviceBwProfileId

1.3.6.1.4.1.164.6.3.6.1.5

Unsigned32

read-create

This variable holds the index of the Ingress BW profile assigned to that service.

evcCosTable

1.3.6.1.4.1.164.6.3.7

not-accessible

This table defines mapping of Ethernet Virtual Connection (EVC) ID to Class of Service (CoS) ID

evcCosEntry

1.3.6.1.4.1.164.6.3.7.1

not-accessible

An entry in table.

U32 evcCosCnfgIdx

1.3.6.1.4.1.164.6.3.7.1.1

Unsigned32

not-accessible

This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.

U32 evcCosEvcIdx

1.3.6.1.4.1.164.6.3.7.1.2

Unsigned32

not-accessible

This attribute indicates EVC Id.

ROW evcCosRowStatus

1.3.6.1.4.1.164.6.3.7.1.3

RowStatus

read-create

This attribute allows to create/delete a row in this table.

STR evcCosEvcName

1.3.6.1.4.1.164.6.3.7.1.5

SnmpAdminString

read-create

A string that identifies the EVC. It should be unique in the Maintenance Domain (i.e., in the managed network) Used as MEG ID field in OAM messages.

U32 evcCosSpVlanId

1.3.6.1.4.1.164.6.3.7.1.6

Unsigned32

read-create

This object indicates the SP (Service Provider) VLAN used when sending an OAM message for the specified EVC.

serviceStatTable

1.3.6.1.4.1.164.6.3.8

not-accessible

Service statistics table.

serviceStatEntry

1.3.6.1.4.1.164.6.3.8.1

not-accessible

An entry in the Service Statistics Table.

INT serviceStatDirection

1.3.6.1.4.1.164.6.3.8.1.1

INTEGER

not-accessible

The direction in wich the measurement is taken.

G32 srvForwardGreenPackets

1.3.6.1.4.1.164.6.3.8.1.2

Gauge32

read-only

This attribute displays the counted number of forwarded packets that where marked Green.

G32 srvForwardGreenPacktesOverflow

1.3.6.1.4.1.164.6.3.8.1.3

Gauge32

read-only

This attribute displays the number of times that the forwardGreenPackets counter has overflowed.

G32 srvForwardYellowPackets

1.3.6.1.4.1.164.6.3.8.1.4

Gauge32

read-only

This attribute displays the counted number of forwarded packets that where marked Yellow.

G32 srvForwardYellowPacketsOverflow

1.3.6.1.4.1.164.6.3.8.1.5

Gauge32

read-only

This attribute displays the number of times that the forwardYellowPackets counter has overflowed.

G32 srvDiscardGreenPacket

1.3.6.1.4.1.164.6.3.8.1.6

Gauge32

read-only

This attribute displays the counted number of discarded packets that where marked Green.

G32 srvDiscardGreenPacketOverflow

1.3.6.1.4.1.164.6.3.8.1.7

Gauge32

read-only

This attribute displays the number of times that the discardGreenPacket counter has overflowed.

G32 srvDiscardYellowRedPackets

1.3.6.1.4.1.164.6.3.8.1.8

Gauge32

read-only

This attribute displays the counted number of discarded packets that where marked Yellow or Red.

G32 srvDiscardYellowRedPacketsOverflow

1.3.6.1.4.1.164.6.3.8.1.9

Gauge32

read-only

This attribute displays the number of times that the discardYellowRedPackets counter has overflowed.

G32 srvForwardGreenBytes

1.3.6.1.4.1.164.6.3.8.1.10

Gauge32

read-only

This attribute displays the counted number of forwarded bytes that where marked Green.

G32 srvForwardGreenBytesOverflow

1.3.6.1.4.1.164.6.3.8.1.11

Gauge32

read-only

This attribute displays the number of times that the forwardGreenBytes counter has overflowed.

G32 srvForwardYellowBytes

1.3.6.1.4.1.164.6.3.8.1.12

Gauge32

read-only

This attribute displays the counted number of forwarded bytes that where marked Yellow.

G32 srvForwardYellowBytesOverflow

1.3.6.1.4.1.164.6.3.8.1.13

Gauge32

read-only

This attribute displays the number of times that the forwardYellowBytes counter has overflowed.

G32 srvDiscardGreenBytes

1.3.6.1.4.1.164.6.3.8.1.14

Gauge32

read-only

This attribute displays the counted number of discarded bytes that where marked Green.

G32 srvDiscardGreenBytesOverflow

1.3.6.1.4.1.164.6.3.8.1.15

Gauge32

read-only

This attribute displays the number of times that the discardGreenBytes counter has overflowed.

G32 srvDiscardYellowRedBytes

1.3.6.1.4.1.164.6.3.8.1.16

Gauge32

read-only

This attribute displays the counted number of discarded bytes that where marked Yellow or Red.

G32 srvDiscardYellowRedBytesOverflow

1.3.6.1.4.1.164.6.3.8.1.17

Gauge32

read-only

This attribute displays the number of times that the discardYellowRedBytes counter has overflowed.

INT srvResetStatsCmd

1.3.6.1.4.1.164.6.3.8.1.18

INTEGER

read-create

Reset statistic counters of the service.

G32 srvDiscardYellowPackets

1.3.6.1.4.1.164.6.3.8.1.19

Gauge32

read-only

This attribute displays the counted number of discarded packets that where marked Yellow.

G32 srvDiscardYellowPacketsOverflow

1.3.6.1.4.1.164.6.3.8.1.20

Gauge32

read-only

This attribute displays the number of times that the discardYellowPackets counter has overflowed.

G32 srvDiscardYellowBytes

1.3.6.1.4.1.164.6.3.8.1.21

Gauge32

read-only

This attribute displays the counted number of discarded bytes that where marked Yellow.

G32 srvDiscardYellowBytesOverflow

1.3.6.1.4.1.164.6.3.8.1.22

Gauge32

read-only

This attribute displays the number of times that the discardYellowBytes counter has overflowed.

G32 srvDiscardRedPackets

1.3.6.1.4.1.164.6.3.8.1.23

Gauge32

read-only

This attribute displays the counted number of discarded packets that where marked Red.

G32 srvDiscardRedPacketsOverflow

1.3.6.1.4.1.164.6.3.8.1.24

Gauge32

read-only

This attribute displays the number of times that the discardRedPackets counter has overflowed.

G32 srvDiscardRedBytes

1.3.6.1.4.1.164.6.3.8.1.25

Gauge32

read-only

This attribute displays the counted number of discarded bytes that where marked Red.

G32 srvDiscardRedBytesOverflow

1.3.6.1.4.1.164.6.3.8.1.26

Gauge32

read-only

This attribute displays the number of times that the discardRedBytes counter has overflowed.

mappingProfileObjects

1.3.6.1.4.1.164.6.3.9

flowMappingProfileTable

1.3.6.1.4.1.164.6.3.9.1

not-accessible

This table holds flow mapping profiles.

flowMappingProfileEntry

1.3.6.1.4.1.164.6.3.9.1.1

not-accessible

Each entry in this table describes one Flow mapping profile with one of its Flow Mapping supported, according to the Priority order. The information includes a reference to a Flow Mapping index.

U32 flowMappingProfileIndex

1.3.6.1.4.1.164.6.3.9.1.1.1

Unsigned32

not-accessible

A running index for the Flow Mapping Profile table.

INT flowMappingProfilePriority

1.3.6.1.4.1.164.6.3.9.1.1.2

INTEGER

not-accessible

The priority of the Mapping selected by flowMappingProfileMapIndex within the Flow Mapping Profile.

ROW flowMappingProfileRowStatus

1.3.6.1.4.1.164.6.3.9.1.1.3

RowStatus

read-create

This attribute is used to create a new row or to delete an existing row in the table.

U32 flowMappingProfileNumOfMaps

1.3.6.1.4.1.164.6.3.9.1.1.4

Unsigned32

read-create

This attribute determines the number of the mappings associated to the Flow Mapping Profile.

U32 flowMappingProfileMapIndex

1.3.6.1.4.1.164.6.3.9.1.1.5

Unsigned32

read-create

This attribute holds a reference to the mapping index. It specifies the mapping selected for the Mapping Profile for the selected Priority. When flowMappingProfileNumOfMaps=0, this attribute is not relevant.

STR flowMappingProfileName

1.3.6.1.4.1.164.6.3.9.1.1.6

SnmpAdminString

read-create

This attribute defines the name assigned to flowMappingIndex profile.

qosFlowMappingTable

1.3.6.1.4.1.164.6.3.9.2

not-accessible

A table of Flow Mapping.

qosFlowMappingEntry

1.3.6.1.4.1.164.6.3.9.2.1

not-accessible

Each entry in this table describes one Flow Mapping. The information includes combination (AND function) of all the classifications, as defined in the qosFlowMappingCriteria field. Classifiers are: TOS, DSCP, VLAN ID, MAC and IP source and destination addresses, IP protocol, IP Precedence, TCP and UDP source and destination ports.

U32 qosFlowMappingIdx1

1.3.6.1.4.1.164.6.3.9.2.1.1

Unsigned32

not-accessible

- In case the table is accessed via flowMappingProfileTable this is a running index for the QoS Flow Mapping table. - In case the table is not accessed via flowMappingProfileTable, this will be the ifIndex of the XNI (bridge port) to which the QoS mapping applies.

U32 qosFlowMappingIdx2

1.3.6.1.4.1.164.6.3.9.2.1.2

Unsigned32

not-accessible

An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the index of the Flow (EVC) to which the QoS mapping applies.

U32 qosFlowMappingIdx3

1.3.6.1.4.1.164.6.3.9.2.1.3

Unsigned32

not-accessible

An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the Priority to which the QoS mapping applies.

ROW qosFlowMappingRowStatus

1.3.6.1.4.1.164.6.3.9.2.1.4

RowStatus

read-create

This attribute is used to create a new row or to delete an existing row in the table.

BIT qosFlowMappingCriteria

1.3.6.1.4.1.164.6.3.9.2.1.5

Bits

read-create

This attribute determines upon which criterion the flow will be mapped.

U32 qosFlowMappingIeee802dot1p

1.3.6.1.4.1.164.6.3.9.2.1.6

Unsigned32

read-create

This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different 802.1 P-bit value. Setting '1' to the bit means that the corresponding 802.1 P-bit value is applicable. It is relevant only in case the ieee802dot1p bit(0) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingTos

1.3.6.1.4.1.164.6.3.9.2.1.7

Unsigned32

read-create

This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different TOS value. Setting '1' to the bit means that the corresponding TOS value is applicable. It is relevant only in case the tos bit (1) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingFromDscp

1.3.6.1.4.1.164.6.3.9.2.1.8

Unsigned32

read-create

This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingToDscp

1.3.6.1.4.1.164.6.3.9.2.1.9

Unsigned32

read-create

This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingFromVlanId

1.3.6.1.4.1.164.6.3.9.2.1.10

Unsigned32

read-create

This attribute determines the first VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingToVlanId

1.3.6.1.4.1.164.6.3.9.2.1.11

Unsigned32

read-create

This attribute determines the last VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.

MAC qosFlowMappingFromSrcMacAddr

1.3.6.1.4.1.164.6.3.9.2.1.12

MacAddress

read-create

This attribute determines the first source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.

MAC qosFlowMappingToSrcMacAddr

1.3.6.1.4.1.164.6.3.9.2.1.13

MacAddress

read-create

This attribute determines the last source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.

MAC qosFlowMappingFromDestMacAddr

1.3.6.1.4.1.164.6.3.9.2.1.14

MacAddress

read-create

This attribute determines the first destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.

MAC qosFlowMappingToDestMacAddr

1.3.6.1.4.1.164.6.3.9.2.1.15

MacAddress

read-create

This attribute determines the last destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.

IP qosFlowMappingFromSrcIpAddr

1.3.6.1.4.1.164.6.3.9.2.1.16

IpAddress

read-create

This attribute determines the first source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.

IP qosFlowMappingToSrcIpAddr

1.3.6.1.4.1.164.6.3.9.2.1.17

IpAddress

read-create

This attribute determines the last source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.

IP qosFlowMappingFromDestIpAddr

1.3.6.1.4.1.164.6.3.9.2.1.18

IpAddress

read-create

This attribute determines the first destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.

IP qosFlowMappingToDestIpAddr

1.3.6.1.4.1.164.6.3.9.2.1.19

IpAddress

read-create

This attribute determines the last destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingFromTcpSrcPort

1.3.6.1.4.1.164.6.3.9.2.1.20

Unsigned32

read-create

This attribute determines the first TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingToTcpSrcPort

1.3.6.1.4.1.164.6.3.9.2.1.21

Unsigned32

read-create

This attribute determines the last TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingFromTcpDestPort

1.3.6.1.4.1.164.6.3.9.2.1.22

Unsigned32

read-create

This attribute determines the first TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingToTcpDestPort

1.3.6.1.4.1.164.6.3.9.2.1.23

Unsigned32

read-create

This attribute determines the last TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingFromUdpSrcPort

1.3.6.1.4.1.164.6.3.9.2.1.24

Unsigned32

read-create

This attribute determines the first UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingToUdpSrcPort

1.3.6.1.4.1.164.6.3.9.2.1.25

Unsigned32

read-create

This attribute determines the last UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingFromUdpDestPort

1.3.6.1.4.1.164.6.3.9.2.1.26

Unsigned32

read-create

This attribute determines the first UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingToUdpDestPort

1.3.6.1.4.1.164.6.3.9.2.1.27

Unsigned32

read-create

This attribute determines the last UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingFromIpPrecedence

1.3.6.1.4.1.164.6.3.9.2.1.28

Unsigned32

read-create

This attribute determines the first IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingToIpPrecedence

1.3.6.1.4.1.164.6.3.9.2.1.29

Unsigned32

read-create

This attribute determines the last IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingInnerIeee802dot1p

1.3.6.1.4.1.164.6.3.9.2.1.30

Unsigned32

read-create

This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different inner 802.1 P-bit value. Setting '1' to the bit means that the corresponding inner 802.1 P-bit value is applicable. It is relevant only in case the innerIeee802dot1p bit (13) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingFromInnerVlanId

1.3.6.1.4.1.164.6.3.9.2.1.31

Unsigned32

read-create

This attribute determines the first inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.

U32 qosFlowMappingToInnerVlanId

1.3.6.1.4.1.164.6.3.9.2.1.32

Unsigned32

read-create

This attribute determines the last inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.

cosProfileTable

1.3.6.1.4.1.164.6.3.10

not-accessible

Class of Service Profile table. Each profile holds a priority method, and a mappring function that maps the priority values (range according to the method) into CoS values.

cosProfileEntry

1.3.6.1.4.1.164.6.3.10.1

not-accessible

A conceptual row where each row contains one CoS attributes.

U32 cosProfileIndex

1.3.6.1.4.1.164.6.3.10.1.1

Unsigned32

not-accessible

Defines the CoS Profile ID.

ROW cosProfileRowStatus

1.3.6.1.4.1.164.6.3.10.1.2

RowStatus

read-create

This attribute is used to create a new row or to delete an existing row in the table.

INT cosProfileCosMethod

1.3.6.1.4.1.164.6.3.10.1.3

INTEGER

read-create

Defines the priority method upon CoS mapping is done.

STR cosProfileName

1.3.6.1.4.1.164.6.3.10.1.4

SnmpAdminString

read-create

This attribute defines the name assigned to CoS profile.

OCT cosProfileCosMapping

1.3.6.1.4.1.164.6.3.10.1.5

OCTET STRING

read-create

This attribute defines the value of the CoS that is assigned for each priority. The number of the valid octets depends upon the priority method selected: Octet 0 corresponds to priority = 0 Octet 1 corresponds to priority = 1 ... Octet 63 corresponds to priority = 63.

queueProfileObjects

1.3.6.1.4.1.164.6.3.11

qProfileTable

1.3.6.1.4.1.164.6.3.11.1

not-accessible

This table defines the profiles for a cluster of queues.

qProfileEntry

1.3.6.1.4.1.164.6.3.11.1.1

not-accessible

A conceptual row where each row contains one Queue Cluster attribute.

U32 qProfileIndex

1.3.6.1.4.1.164.6.3.11.1.1.1

Unsigned32

not-accessible

Defines the Queue Cluster Profile ID.

ROW qProfileRowStatus

1.3.6.1.4.1.164.6.3.11.1.1.2

RowStatus

read-create

This attribute is used to create a new row or to delete an existing row in the table.

STR qProfileName

1.3.6.1.4.1.164.6.3.11.1.1.3

SnmpAdminString

read-create

This attribute holds the name of the Queue cluster profile.

U32 qProfileNumberOfInternalQ

1.3.6.1.4.1.164.6.3.11.1.1.4

Unsigned32

read-create

This attribute holds the number of the internal queue profiles that are pointed by qInternalQProfile.

OCT qProfileInternalQProfile

1.3.6.1.4.1.164.6.3.11.1.1.5

OCTET STRING

read-create

This attribute holds the indexes to the queue profiles in the qInternalProfileTable. Each couple of octets holds an index to the qInternalProfileTable.

qInternalProfileTable

1.3.6.1.4.1.164.6.3.11.2

not-accessible

This table holds queue profiles.

qInternalProfileEntry

1.3.6.1.4.1.164.6.3.11.2.1

not-accessible

A conceptual row where each row contains one Queue attribute.

U32 qInternalProfileIndex

1.3.6.1.4.1.164.6.3.11.2.1.1

Unsigned32

not-accessible

Defines the Queue Profile ID.

ROW qInternalProfileRowStatus

1.3.6.1.4.1.164.6.3.11.2.1.2

RowStatus

read-create

This attribute is used to create a new row or to delete an existing row in the table.

INT qInternalProfileScheduling

1.3.6.1.4.1.164.6.3.11.2.1.3

INTEGER

read-create

This attribute determines the queue scheduling method.

U32 qInternalProfileWFQWeight

1.3.6.1.4.1.164.6.3.11.2.1.4

Unsigned32

read-create

This attribute determines the weight that each WFQ (Weighted Fair Queue) participant gets. It is applicable only when scheduling is configured to WFQ.

U32 qInternalProfileQueueLength

1.3.6.1.4.1.164.6.3.11.2.1.5

Unsigned32

read-create

This attribute determines the length of the queue.

U32 qInternalProfileWredStartDropThresh

1.3.6.1.4.1.164.6.3.11.2.1.6

Unsigned32

read-create

This attribute determines the length that the queue (Start Value) must reach before the packets colored yellow will start being dropped by the WRED (Weighted Random Early Detection/Discard) mechanism. WRED is one the most commonly used method for congestion avoidance.

U32 qInternalProfileWredDropAllThresh

1.3.6.1.4.1.164.6.3.11.2.1.7

Unsigned32

read-create

This attribute determines the length that the queue (Stop Value) must reach before the WRED (Weighted Random Early Detection) shaper mechanism stops dropping randomly, and just drops all further packets marked as yellow.

U32 qInternalProfileWredDropProbability

1.3.6.1.4.1.164.6.3.11.2.1.8

Unsigned32

read-create

This attribute determines the percentage of packets that are being dropped at the point when the length of the queue reaches the Stop value. So, effectively, this defines how quickly the rate of dropping packet must increase as the queue length grows from the Start Value to the Stop Value.

U32 qInternalProfileRateLimit

1.3.6.1.4.1.164.6.3.11.2.1.9

Unsigned32

read-create

This attribute determines the Rate Limit of the queue in Kbps. Value=0 represents best effort.

U32 qInternalProfileShaperProfile

1.3.6.1.4.1.164.6.3.11.2.1.10

Unsigned32

read-create

This attribute defines the Shaper Profile (bwProfileIndex from bwProfileTable) assigned to this qInternalProfile. Valid range of bwProfileIndex for Shaper Profiles is 0x8000001-0x8000041. If set to '0', no profile is assigned to this qInternalProfile.

queueGroupTable

1.3.6.1.4.1.164.6.3.11.3

not-accessible

This table defines the queue groups/blocks,their level and connections between them.

queueGroupEntry

1.3.6.1.4.1.164.6.3.11.3.1

not-accessible

A conceptual row where each row contains one Queue group.

STR queueGroupName

1.3.6.1.4.1.164.6.3.11.3.1.1

SnmpAdminString

not-accessible

Defines the Queue Group unique name.

U32 queueGroupQBlockLevel

1.3.6.1.4.1.164.6.3.11.3.1.2

Unsigned32

not-accessible

This attribute holds the Level of the Queue Block .First level is 1. NA=2^32-1.

U32 queueGroupQBlockIdx

1.3.6.1.4.1.164.6.3.11.3.1.3

Unsigned32

not-accessible

This attribute holds the ID of the Queue Block. NA=2^32-1.

ROW queueGroupRowStatus

1.3.6.1.4.1.164.6.3.11.3.1.4

RowStatus

read-create

This attribute is used to create a new row or to delete an existing row in the table.

U32 queueGroupQBlockProfile

1.3.6.1.4.1.164.6.3.11.3.1.5

Unsigned32

read-create

This attribute defines the Queue profile assigned to this Queue Block. This object points to qProfileIndex in qProfileTable.

U32 queueGroupQBlockShaperProfile

1.3.6.1.4.1.164.6.3.11.3.1.6

Unsigned32

read-create

This attribute defines the Shaper profile assigned to this Queue Block.

STR queueGroupPointToQBlock

1.3.6.1.4.1.164.6.3.11.3.1.7

SnmpAdminString

read-create

This attribute defines the Queue Block name of the next Queue Block level that is pointed by this Queue Block.

U32 queueGroupPointToInternalQueue

1.3.6.1.4.1.164.6.3.11.3.1.8

Unsigned32

read-create

This attribute defines the internal queue whithin queueGroupPointToQBlock that is pointed by this Queue Block.

STR queueGroupQBlockName

1.3.6.1.4.1.164.6.3.11.3.1.9

SnmpAdminString

read-create

This attribute holds the name of the Queue Block.

markingProfileTable

1.3.6.1.4.1.164.6.3.12

not-accessible

Marking profile table. Each profile holds a marking function which converts CoS values to Service Provider priority values.

markingProfileEntry

1.3.6.1.4.1.164.6.3.12.1

not-accessible

A conceptual row where each row contains one Marking attribute.

U32 markingProfileIndex

1.3.6.1.4.1.164.6.3.12.1.1

Unsigned32

not-accessible

Defines the Marking Profile ID.

ROW markingProfileRowStatus

1.3.6.1.4.1.164.6.3.12.1.2

RowStatus

read-create

This attribute is used to create a new row or to delete an existing row in the table.

STR markingProfileName

1.3.6.1.4.1.164.6.3.12.1.3

SnmpAdminString

read-create

This attribute defines the unique name assigned to the Marking profile.

OCT markingSpVlanPBit

1.3.6.1.4.1.164.6.3.12.1.4

OCTET STRING

read-create

For ETX-202A : This attribute defines the value of the SP VLAN P-Bit that is assigned for each CoS: Octet 0 corresponds to CoS = 0 Octet 1 corresponds to CoS = 1 ... Octet 7 corresponds to CoS = 7. For LA-210 from V1.5 : This attribute defines the value of the SP VLAN P-Bit that is assigned for each frame according to the value of markingProfileMethod parameter : Octet 0 corresponds to value 0 of 802.1 P-bit/DSCP/TOS. Octet 1 corresponds to value 1 of 802.1 P-bit/DSCP/TOS. ... Octet 7 corresponds to value 7 of 802.1 P-bit/DSCP/TOS. Octets 8-63 correspond to DSCP values 8-63.

INT markingProfileMethod

1.3.6.1.4.1.164.6.3.12.1.5

INTEGER

read-create

This attribute defines the method upon which marking is done.

radTransport

1.3.6.1.4.1.164.6.4

radTransportDomains

1.3.6.1.4.1.164.6.4.1

radTransportDomainSnmpEfmOam

1.3.6.1.4.1.164.6.4.1.1

The SNMP over EFM OAM transport domain. The corresponding transport address is of type RadTransportAddressEfmOam for EFM OAM addresses (port).

1.3.6.1.4.1.164.7

1.3.6.1.4.1.164.11

1.3.6.1.4.1.164.11.7

1.3.6.1.4.1.164.11.7.2

wrSysConfig

1.3.6.1.4.1.164.11.7.2.1

INT wrBraodcastCtrlCmd

1.3.6.1.4.1.164.11.7.2.1.1

INTEGER

read-write

This parameter is a command to the webranger CPU. It enables blocking or forwarding broadcast frames, which may cause a trigger to a connection. block (1) - blocks the broadcast frames. forward (2) - forwards the broadcast frames. blockLinkPropagation (3) - blocks the broadcast frames to the links, tx to the LAN.

INT wrFrSelfLearningMode

1.3.6.1.4.1.164.11.7.2.1.2

INTEGER

read-write

This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol. off - will get the configuration by setting it. on - disables configuration and start self learning.

INT wrGratuitousArp

1.3.6.1.4.1.164.11.7.2.1.3

INTEGER

read-write

This parameter enables/disables the Gratuitous ARP feature. When enabled, the feature means: when receiving ARP with sender's Source IP Address that already exists in the ARP table - replace MAC Address with sender's Source MAC Address.

wrIpRouterInfo

1.3.6.1.4.1.164.11.7.2.2

wrConfigIpDhcp

1.3.6.1.4.1.164.11.7.2.2.1

INT wrDhcpAction

1.3.6.1.4.1.164.11.7.2.2.1.1

INTEGER

read-write

Activating (disable/enable) DHCP server operation. Since DHCP Server and DHCP Relay cannot reside in same device, DHCP Relay may be enabled (per interface), only if server action is disabled. For some devices, this object is used in order to enable/disable the DHCP Client. See device SDS.

wrDhcpTable

1.3.6.1.4.1.164.11.7.2.2.1.2

not-accessible

A list of DHCP entries. The number of entries is up to DHCP current entries, according to the WEBRANger model.

wrDhcpEntry

1.3.6.1.4.1.164.11.7.2.2.1.2.1

not-accessible

DHCP parameters per entry of the DHCP table.

IP wrDhcpLowIpAddress

1.3.6.1.4.1.164.11.7.2.2.1.2.1.1

IpAddress

read-create

DHCP Low Ip Address.

IP wrDhcpHighIpAddress

1.3.6.1.4.1.164.11.7.2.2.1.2.1.2

IpAddress

read-create

DHCP High Ip Address.

IP wrDhcpIpMaskAddress

1.3.6.1.4.1.164.11.7.2.2.1.2.1.3

IpAddress

read-create

IP mask Address.

IP wrDhcpDefaultGateway

1.3.6.1.4.1.164.11.7.2.2.1.2.1.4

IpAddress

read-create

Default Gateway's IP Address.

IP wrDhcpPrimaryDNS

1.3.6.1.4.1.164.11.7.2.2.1.2.1.5

IpAddress

read-create

Primary DNS.

IP wrDhcpSecondaryDNS

1.3.6.1.4.1.164.11.7.2.2.1.2.1.6

IpAddress

read-create

Secondary DNS.

INT wrDhcpInterface

1.3.6.1.4.1.164.11.7.2.2.1.2.1.7

INTEGER

read-create

The IP addresse allocation is done according to the interface type from which the DHCP request arrives.

ROW wrDhcpRowStatus

1.3.6.1.4.1.164.11.7.2.2.1.2.1.8

RowStatus

read-create

This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrDhcpRowStatus.id = active(1). For destroying a row, the NMS should set: wrDhcpStatus.id = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).

I32 wrDhcpIpAddressLeaseTime

1.3.6.1.4.1.164.11.7.2.2.1.2.1.9

Integer32

read-create

Allocated IP Address lease time in seconds. A zero value specifies no time limitation.

STR wrDhcpPoolName

1.3.6.1.4.1.164.11.7.2.2.1.2.1.10

SnmpAdminString

read-create

DHCP pool name - string with max length of 10 characters

IP wrDhcpTftpServerIp

1.3.6.1.4.1.164.11.7.2.2.1.2.1.11

IpAddress

read-create

DHCP pool - TFTP-server IP Address.

STR wrDhcpConfigFileName

1.3.6.1.4.1.164.11.7.2.2.1.2.1.12

SnmpAdminString

read-create

TFTP-name of the configuration File Name for DHCP pool.

dhcpPoolAllocTable

1.3.6.1.4.1.164.11.7.2.2.1.3

not-accessible

A list of DHCP Pool Allocation entries. Each entry (row) consist of a single IP Address belonging to DHCP pool whose lowest IP address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing, or may already be leased (in use) by Host it's MacAddress is dhcpPoolAllocMacAddress. Time left for leasing period is indicated by dhcpPoolAllocTimeLeft. All posible statuses of IP address are indicated and controlled by dhcpPoolAllocFlags

dhcpPoolAllocEntry

1.3.6.1.4.1.164.11.7.2.2.1.3.1

not-accessible

DHCP Pool Allocation parameters per entry of the DHCP Pool Allocation table.

IP dhcpPoolAllocLowIpAddress

1.3.6.1.4.1.164.11.7.2.2.1.3.1.1

IpAddress

read-only

Lowest IP address of this pool, value eqaul to wrDhcpLowIpAddress for the pool.

IP dhcpPoolAllocLeasingIpAddress

1.3.6.1.4.1.164.11.7.2.2.1.3.1.2

IpAddress

read-only

Single IP Address belonging to dhcp pool whose Lowest Ip Address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing or may be leased by Host its MacAddress is dhcpPoolAllocMacAddress. All posible statuses of IP address are indicated by dhcpPoolAllocFlags

MAC dhcpPoolAllocMacAddress

1.3.6.1.4.1.164.11.7.2.2.1.3.1.3

MacAddress

read-only

MAC Address to which the IP address has been leased

I32 dhcpPoolAllocTimeLeft

1.3.6.1.4.1.164.11.7.2.2.1.3.1.4

Integer32

read-only

IP address leasing time left in seconds

INT dhcpPoolAllocFlags

1.3.6.1.4.1.164.11.7.2.2.1.3.1.5

INTEGER

read-only

These flags indicates status of each IP address. User may change value to free, via dhcpPoolAllocFreeCmd

INT dhcpPoolAllocFreeCmd

1.3.6.1.4.1.164.11.7.2.2.1.3.1.6

INTEGER

read-write

Setting this attribute to On (3), will enforce the agent to Free this entry. The Agent will change the value of this MIB object to off(2) automatically, after performing the command. Setting this object to off(2), will do nothing

dhcpRelayTable

1.3.6.1.4.1.164.11.7.2.2.1.4

not-accessible

A list of DHCP relay entries.

dhcpRelayEntry

1.3.6.1.4.1.164.11.7.2.2.1.4.1

not-accessible

DHCP Relay parameters per entry of the DHCP relay table.

INT dhcpRelayAction

1.3.6.1.4.1.164.11.7.2.2.1.4.1.1

INTEGER

read-write

Setting this attribute to enable (3), will enable DHCP Relay action for this interface (Only if DHCP Server is disabled for device - wrDhcpAction=disable). dhcpRelayServerIpAddressaddress should not be 0.0.0.0 when enable is set

IP dhcpRelayServerIpAddress

1.3.6.1.4.1.164.11.7.2.2.1.4.1.2

IpAddress

read-write

DHCP Server IP Address.

I32 dhcpRelayMaxHop

1.3.6.1.4.1.164.11.7.2.2.1.4.1.3

Integer32

read-write

Maximum number of hops till DHCP Server. upper limit is 16 hops

INT wrDhcpPort

1.3.6.1.4.1.164.11.7.2.2.1.5

INTEGER

read-write

This parameter defines the port that DHCP flow will be actiavted.

dhcpClientTable

1.3.6.1.4.1.164.11.7.2.2.1.6

not-accessible

A list of DHCP client entries.

dhcpClientEntry

1.3.6.1.4.1.164.11.7.2.2.1.6.1

not-accessible

DHCP Client parameters per entry of the DHCP Client table.

INT dhcpClientAction

1.3.6.1.4.1.164.11.7.2.2.1.6.1.1

INTEGER

read-write

This parameter default value is enable(3). Setting this attribute to disable (2), will disable DHCP Client action for this interface. This parameter can be changed to disable (2) only (it cannot be changed from disable to enable).

IP dhcpClientServerIpAddress

1.3.6.1.4.1.164.11.7.2.2.1.6.1.2

IpAddress

read-write

DHCP Server IP Address.

I32 dhcpClientLeaseExpirationTime

1.3.6.1.4.1.164.11.7.2.2.1.6.1.3

Integer32

read-only

This parameter holds the time (in minutes) left until lease expiration.

STR dhcpClientStatus

1.3.6.1.4.1.164.11.7.2.2.1.6.1.4

DisplayString

read-only

This parametr displays the DHCP status.

dhcpIfClientTable

1.3.6.1.4.1.164.11.7.2.2.1.7

not-accessible

DHCP client entries for each Interface.

dhcpIfClientEntry

1.3.6.1.4.1.164.11.7.2.2.1.7.1

not-accessible

DHCP Clients per entry of the DHCP Interface Client table.

IP dhcpIfClientIpAddress

1.3.6.1.4.1.164.11.7.2.2.1.7.1.2

IpAddress

read-create

DHCP Client IP Address.

ROW dhcpIfClientRowStatus

1.3.6.1.4.1.164.11.7.2.2.1.7.1.3

RowStatus

read-create

The row status used for creating, modifying, and deleting instances of the columnar objects in the dhcpIfClientTable. For Vmux Devices, it will be possible only to Delete instances. The addition of Clients will be done automatically by the Server according to Network messages that are sent by the Clients; not via SNMP. In order to Delete a Client, this MIB object should be set to: destroy (6).

INT dhcpServerAction

1.3.6.1.4.1.164.11.7.2.2.1.8

INTEGER

read-write

This variable enables the operator to perform one of the specified actions on the Server. deleteAllClients (3) is an option that is used for a device functioning as a server. It will remove all the clients from all the interfaces of the device. When the operation is complete, the agent will return a noOp (2) value.

wrConfigIpDNS

1.3.6.1.4.1.164.11.7.2.2.2

INT wrDNSRelayAction

1.3.6.1.4.1.164.11.7.2.2.2.1

INTEGER

read-write

When Enabled, device will act as a DNS Relay: whenever the device receives a DNS request from its host, it will forward it to the DNS server as if the request was initiated by the device itself. The reply from the DNS server is forwarded by the device to the host as if the device was answering the request.

wrConfigIpxRouterInfo

1.3.6.1.4.1.164.11.7.2.3

INT wrAutoLearnLanIpxNets

1.3.6.1.4.1.164.11.7.2.3.1

INTEGER

read-write

Activating (disable/enable) the auto-learn operation.

wrLanIpxNetTable

1.3.6.1.4.1.164.11.7.2.3.2

not-accessible

Lan IPX nets Table.

wrLanIpxNetEntry

1.3.6.1.4.1.164.11.7.2.3.2.1

not-accessible

IPX Nets per frame type & LAN port. The table entries will be created by the agent

I32 wrLanIfIndex

1.3.6.1.4.1.164.11.7.2.3.2.1.1

Integer32

read-only

LAN port ifIndex.

INT wrLanIpxFrameType

1.3.6.1.4.1.164.11.7.2.3.2.1.2

INTEGER

read-only

Frame Type

IP wrIpxNetAddress

1.3.6.1.4.1.164.11.7.2.3.2.1.3

IpAddress

read-write

Net address per Frame Type & LAN port.

IP wrDialInIpxNet

1.3.6.1.4.1.164.11.7.2.3.3

IpAddress

read-write

Net address through a link.

ripSapIfConfTable

1.3.6.1.4.1.164.11.7.2.3.4

not-accessible

A list of Interfaces which require separate configuration in RIP/SAP.

ripSapIfConfEntry

1.3.6.1.4.1.164.11.7.2.3.4.1

not-accessible

A Single Routing Domain in a single Subnet.

I32 ripSapIfConfIfIndex

1.3.6.1.4.1.164.11.7.2.3.4.1.1

Integer32

read-only

The interface ifIndex.

INT ripSapIfConfMode

1.3.6.1.4.1.164.11.7.2.3.4.1.2

INTEGER

read-create

The ifIndex RIP/SAP mode.

ROW ripSapIfConfStatus

1.3.6.1.4.1.164.11.7.2.3.4.1.3

RowStatus

read-create

This attribute allows to create/delete a row in this table. For creating a row, the NMS should set ripSapIfConfStatus.id1 = active(1). For destroying a row, the NMS should set: ripSapIfConfStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).

wrInterface

1.3.6.1.4.1.164.11.7.2.4

wrIpAddressTable

1.3.6.1.4.1.164.11.7.2.4.1

not-accessible

Link IP addresses Table.

wrIpAddressEntry

1.3.6.1.4.1.164.11.7.2.4.1.1

not-accessible

Ip Address per Link

I32 wrIpIfIndex

1.3.6.1.4.1.164.11.7.2.4.1.1.1

Integer32

read-only

Port interface index.

IP wrIpAddress

1.3.6.1.4.1.164.11.7.2.4.1.1.2

IpAddress

read-create

Link IP Address.

IP wrIpMask

1.3.6.1.4.1.164.11.7.2.4.1.1.3

IpAddress

read-create

Link IP mask Address.

ROW wrIpRowStatus

1.3.6.1.4.1.164.11.7.2.4.1.1.4

RowStatus

read-create

This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrIpRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrIpRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).

wrSpoofingTable

1.3.6.1.4.1.164.11.7.2.4.2

not-accessible

Spoofing Table.

wrSpoofingEntry

1.3.6.1.4.1.164.11.7.2.4.2.1

not-accessible

Spoofing per Link

I32 wrSpoofingIfIndex

1.3.6.1.4.1.164.11.7.2.4.2.1.1

Integer32

read-only

Port interface index.

I32 wrSpoofingAction

1.3.6.1.4.1.164.11.7.2.4.2.1.2

Integer32

read-create

Spoofing action is applied by bit code: enable : bit 0 set (disable: bit 0 is 0) keepAlive : bit 1 ... : bit 2 and so on. For the above example, to set spoofing to keepAlive action, the object's value will be 3 = [ 2**0 + 2**1 ] Only the Remote WEBRANger will accept this object ! -------

I32 wrSpoofingAgingStation

1.3.6.1.4.1.164.11.7.2.4.2.1.3

Integer32

read-create

Aging time of stations list, in min. The agent 'translates' the time entered in minutes, to 10 min. resolution, as follows: 1..10 min - 10 min 11..20 min - 20 min and so on... 0 is not a valid value. Only the Remote WEBRANger will accept this object ! ----------------

ROW wrSpoofingRowStatus

1.3.6.1.4.1.164.11.7.2.4.2.1.4

RowStatus

read-create

This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrSpoofingRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrSpoofingRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).

wrLanIfTable

1.3.6.1.4.1.164.11.7.2.4.3

not-accessible

Link IP addresses Table.

wrLanIfEntry

1.3.6.1.4.1.164.11.7.2.4.3.1

not-accessible

Ip Address per Link

INT wrLanBridgeRouterMode

1.3.6.1.4.1.164.11.7.2.4.3.1.2

INTEGER

read-write

This parameter indicates whether the link is Bridge or Router and specifies the Router's type.

INT wrLanIfState

1.3.6.1.4.1.164.11.7.2.4.3.1.3

INTEGER

read-write

The LAN is disabled or enabled. For LAN 2 it can be also 'redundancy'.

I32 wrLanIfRdnTimeout

1.3.6.1.4.1.164.11.7.2.4.3.1.4

Integer32

read-write

LAN Redundancy Timeout in seconds. Applicable when wrLanIfState=redundancy.

wrSyncCnfgTable

1.3.6.1.4.1.164.11.7.2.4.4

not-accessible

Configuration table for Async interface.

wrSyncCnfgEntry

1.3.6.1.4.1.164.11.7.2.4.4.1

not-accessible

Configuration table

I32 wrSyncIfIndex

1.3.6.1.4.1.164.11.7.2.4.4.1.1

Integer32

read-only

Sync interface index.

INT wrSyncClkMode

1.3.6.1.4.1.164.11.7.2.4.4.1.2

INTEGER

read-write

Clock Mode.

INT wrSyncClkRate

1.3.6.1.4.1.164.11.7.2.4.4.1.3

INTEGER

read-write

Clock Rate in. Rate can be changed if Clock Mode is Program only.

wrFrCnfgTable

1.3.6.1.4.1.164.11.7.2.4.5

not-accessible

Configuration table for Fr parameters that do not exist in RFC2115.

wrFrCnfgEntry

1.3.6.1.4.1.164.11.7.2.4.5.1

not-accessible

Configuration entry for Fr parameters that do not exist in RFC2115.

INT wrFrDlciLearningMode

1.3.6.1.4.1.164.11.7.2.4.5.1.1

INTEGER

read-write

This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol for the current interface. off - the WR will read the user's configuration for this interface. on - the WR will begin self learning of the current interface's maintanance protocol and DLCIs.

INT wrFrCllmMessages

1.3.6.1.4.1.164.11.7.2.4.5.1.2

INTEGER

read-write

This parameter enables/disables the Webranger to Tx/Rx CLLM (Consolidated Link Layer Management) messages via DLCI 1023. The CLLM messages are link layer control messages. They can be used for example in cases of congestion. The CLLM message contains a code for cause of congestion and list of all DLCIs that should act to reduce data transmission.

radAtm

1.3.6.1.4.1.164.12

atmGen

1.3.6.1.4.1.164.12.2

atmPerfHistory

1.3.6.1.4.1.164.12.2.1

atmIfPerformance

1.3.6.1.4.1.164.12.2.1.1

atmIfDataTable

1.3.6.1.4.1.164.12.2.1.1.1

not-accessible

The ATM interface Data table.

atmIfDataEntry

1.3.6.1.4.1.164.12.2.1.1.1.1

not-accessible

An entry in the ATM interface Data table.

I32 atmIfTimeElapsed

1.3.6.1.4.1.164.12.2.1.1.1.1.1

Integer32

read-only

The number of seconds that have elapsed since the beginning of the near end current error- measurement period.

I32 atmIfValidIntervals

1.3.6.1.4.1.164.12.2.1.1.1.1.2

Integer32

read-only

The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.

C32 atmIfTxCells

1.3.6.1.4.1.164.12.2.1.1.1.1.3

Counter32

read-only

The counter associated with the total number of transmitted cells, encountered by an ATM interface.

C32 atmIfRxCells

1.3.6.1.4.1.164.12.2.1.1.1.1.4

Counter32

read-only

The counter associated with the total number of received cells, encountered by an ATM interface.

C32 atmIfUncorrectedHecs

1.3.6.1.4.1.164.12.2.1.1.1.1.5

Counter32

read-only

The counter associated with the total number of cells with uncorrected HEC errors, encountered by an ATM interface.

atmIfCurrentTable

1.3.6.1.4.1.164.12.2.1.1.2

not-accessible

The ATM interface Current table.

atmIfCurrentEntry

1.3.6.1.4.1.164.12.2.1.1.2.1

not-accessible

An entry in the ATM interface Current table.

G32 atmIfCurrentTxCells

1.3.6.1.4.1.164.12.2.1.1.2.1.1

Gauge32

read-only

The counter associated with the number of transmitted cells, encountered by an ATM interface in the current 15 minute interval.

G32 atmIfCurrentRxCells

1.3.6.1.4.1.164.12.2.1.1.2.1.2

Gauge32

read-only

The counter associated with the number of received cells, encountered by an ATM interface in the current 15 minute interval.

G32 atmIfCurrentCorrectedHecs

1.3.6.1.4.1.164.12.2.1.1.2.1.3

Gauge32

read-only

The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in the current 15 minute interval.

G32 atmIfCurrentUncorrectedHecs

1.3.6.1.4.1.164.12.2.1.1.2.1.4

Gauge32

read-only

The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in the current 15 minute interval.

G32 atmIfCurrentHecErrorSeconds

1.3.6.1.4.1.164.12.2.1.1.2.1.5

Gauge32

read-only

The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in the current 15 minute interval.

atmIfIntervalTable

1.3.6.1.4.1.164.12.2.1.1.3

not-accessible

The ATM interface Interval table.

atmIfIntervalEntry

1.3.6.1.4.1.164.12.2.1.1.3.1

not-accessible

An entry in the ATM interface Interval table.

I32 atmIfIntervalNumber

1.3.6.1.4.1.164.12.2.1.1.3.1.1

Integer32

read-only

A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).

G32 atmIfIntervalTxCells

1.3.6.1.4.1.164.12.2.1.1.3.1.2

Gauge32

read-only

The counter associated with the number of transmitted cells , encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.

G32 atmIfIntervalRxCells

1.3.6.1.4.1.164.12.2.1.1.3.1.3

Gauge32

read-only

The counter associated with the number of received cells, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.

G32 atmIfIntervalCorrectedHecs

1.3.6.1.4.1.164.12.2.1.1.3.1.4

Gauge32

read-only

The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.

G32 atmIfIntervalUncorrectedHecs

1.3.6.1.4.1.164.12.2.1.1.3.1.5

Gauge32

read-only

The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.

G32 atmIfIntervalHecErrorSeconds

1.3.6.1.4.1.164.12.2.1.1.3.1.6

Gauge32

read-only

The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.

atmPvcPerformance

1.3.6.1.4.1.164.12.2.1.2

atmVpPerformance

1.3.6.1.4.1.164.12.2.1.2.1

atmVpCurrentTable

1.3.6.1.4.1.164.12.2.1.2.1.1

not-accessible

The ATM VP Current table.

atmVpCurrentEntry

1.3.6.1.4.1.164.12.2.1.2.1.1.1

not-accessible

An entry in the ATM VP Current table.

I32 atmVpCurrentVpi

1.3.6.1.4.1.164.12.2.1.2.1.1.1.1

Integer32

read-only

The VPI of the VPL.

G32 atmVpCurrentRxCellsClp01

1.3.6.1.4.1.164.12.2.1.2.1.1.1.2

Gauge32

read-only

The counter associated with the number of transmitted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentRxCellsClp0

1.3.6.1.4.1.164.12.2.1.2.1.1.1.3

Gauge32

read-only

The counter associated with the number of received cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentGcra0Violations

1.3.6.1.4.1.164.12.2.1.2.1.1.1.4

Gauge32

read-only

The counter associated with the number of cells violating GCRA0, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentGcra1Violations

1.3.6.1.4.1.164.12.2.1.2.1.1.1.5

Gauge32

read-only

The counter associated with the number of cells violating GCRA1, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentRxAIS

1.3.6.1.4.1.164.12.2.1.2.1.1.1.6

Gauge32

read-only

The counter associated with the number of received AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentTxAIS

1.3.6.1.4.1.164.12.2.1.2.1.1.1.7

Gauge32

read-only

The counter associated with the number of transmitted AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.

G32 atmVpCurrentRxRDI

1.3.6.1.4.1.164.12.2.1.2.1.1.1.8

Gauge32

read-only

The counter associated with the number of received RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentTxRDI

1.3.6.1.4.1.164.12.2.1.2.1.1.1.9

Gauge32

read-only

The counter associated with the number of transmitted RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentContinuityLoss

1.3.6.1.4.1.164.12.2.1.2.1.1.1.10

Gauge32

read-only

The counter associated with the number of loss of continuity cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentUAS

1.3.6.1.4.1.164.12.2.1.2.1.1.1.11

Gauge32

read-only

The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentSES

1.3.6.1.4.1.164.12.2.1.2.1.1.1.12

Gauge32

read-only

The counter associated with the number of Severerly Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpCurrentCDC

1.3.6.1.4.1.164.12.2.1.2.1.1.1.13

Gauge32

read-only

Amount of cells dropped in the current 15 minute interval of the VP connection.

G32 atmVpCurrentTotalDiscards

1.3.6.1.4.1.164.12.2.1.2.1.1.1.14

Gauge32

read-only

The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.

G32 atmVpCurrentClp0Discards

1.3.6.1.4.1.164.12.2.1.2.1.1.1.15

Gauge32

read-only

The total number of valid ATM cells received with CLP=0 and discarded by the traffic policing entity.

G32 atmVpCurrentTotalCellOuts

1.3.6.1.4.1.164.12.2.1.2.1.1.1.16

Gauge32

read-only

The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.

G32 atmVpCurrentClp0CellOuts

1.3.6.1.4.1.164.12.2.1.2.1.1.1.17

Gauge32

read-only

The total number of valid ATM cells transmitted with CLP=0 by this VPL.

G32 atmVpCurrentTaggedOuts

1.3.6.1.4.1.164.12.2.1.2.1.1.1.18

Gauge32

read-only

The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.

G32 atmVpCurrentPCR

1.3.6.1.4.1.164.12.2.1.2.1.1.1.19

Gauge32

read-only

The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second).

G32 atmVpCurrentSCR

1.3.6.1.4.1.164.12.2.1.2.1.1.1.20

Gauge32

read-only

The average traffic rate during the last interval of the VP connection.

G32 atmVpCurrentMCR

1.3.6.1.4.1.164.12.2.1.2.1.1.1.21

Gauge32

read-only

MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second).

G32 atmVpCurrentShaperTotalDiscards

1.3.6.1.4.1.164.12.2.1.2.1.1.1.22

Gauge32

read-only

The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.

G32 atmVpCurrentShaperClp0Discards

1.3.6.1.4.1.164.12.2.1.2.1.1.1.23

Gauge32

read-only

The total number of CLP0 cells discarded due to congestion by the traffic shaper.

G32 atmVpCurrentShaperClp1Discards

1.3.6.1.4.1.164.12.2.1.2.1.1.1.24

Gauge32

read-only

The total number of CLP1 cells discarded due to congestion by the traffic shaper.

atmVpPMCurrentTable

1.3.6.1.4.1.164.12.2.1.2.1.2

not-accessible

The ATM VP Current table for Performance Management.

atmVpPMCurrentEntry

1.3.6.1.4.1.164.12.2.1.2.1.2.1

not-accessible

An entry in the ATM VP Current table for Performance Management.

I32 atmVpPMCurrentVpi

1.3.6.1.4.1.164.12.2.1.2.1.2.1.1

Integer32

read-only

The VPI of the VPL.

INT atmVpPMCurrentDir

1.3.6.1.4.1.164.12.2.1.2.1.2.1.2

INTEGER

read-only

The direction of performance management.

G32 atmVpPMCurrentTxClp01

1.3.6.1.4.1.164.12.2.1.2.1.2.1.3

Gauge32

read-only

The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentTxClp0

1.3.6.1.4.1.164.12.2.1.2.1.2.1.4

Gauge32

read-only

The counter associated with the number of transmitted CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentRxClp01

1.3.6.1.4.1.164.12.2.1.2.1.2.1.5

Gauge32

read-only

The counter associated with the number of received CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentRxClp0

1.3.6.1.4.1.164.12.2.1.2.1.2.1.6

Gauge32

read-only

The counter associated with the number of received CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentErroredCells

1.3.6.1.4.1.164.12.2.1.2.1.2.1.7

Gauge32

read-only

The counter associated with the number of errored cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentLostCells

1.3.6.1.4.1.164.12.2.1.2.1.2.1.8

Gauge32

read-only

The counter associated with the number of lost cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentMisinsertedCells

1.3.6.1.4.1.164.12.2.1.2.1.2.1.9

Gauge32

read-only

The counter associated with the number of misinserted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentECB

1.3.6.1.4.1.164.12.2.1.2.1.2.1.10

Gauge32

read-only

The counter associated with the number of ECB, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentSECB

1.3.6.1.4.1.164.12.2.1.2.1.2.1.11

Gauge32

read-only

The counter associated with the number of SECB, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentES

1.3.6.1.4.1.164.12.2.1.2.1.2.1.12

Gauge32

read-only

The counter associated with the number of Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentSES

1.3.6.1.4.1.164.12.2.1.2.1.2.1.13

Gauge32

read-only

The counter associated with the number of Severely Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.

G32 atmVpPMCurrentUAS

1.3.6.1.4.1.164.12.2.1.2.1.2.1.14

Gauge32

read-only

The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.

INT atmVpPMCurrentIntervalQuality

1.3.6.1.4.1.164.12.2.1.2.1.2.1.15

INTEGER

read-only

If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.

INT atmVpPMCurrentLastDayQuality

1.3.6.1.4.1.164.12.2.1.2.1.2.1.16

INTEGER

read-only

If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.

atmVpIntervalTable

1.3.6.1.4.1.164.12.2.1.2.1.3

not-accessible

The ATM Vp Interval table.

atmVpIntervalEntry

1.3.6.1.4.1.164.12.2.1.2.1.3.1

not-accessible

An entry in the ATM Vp Interval table.

I32 atmVpIntervalVpi

1.3.6.1.4.1.164.12.2.1.2.1.3.1.1

Integer32

read-only

The VPI of the VPL.

I32 atmVpIntervalNumber

1.3.6.1.4.1.164.12.2.1.2.1.3.1.2

Integer32

read-only

A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).

G32 atmVpIntervalRxCellsClp01

1.3.6.1.4.1.164.12.2.1.2.1.3.1.3

Gauge32

read-only

The counter associated with the number of transmitted cells , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalRxCellsClp0

1.3.6.1.4.1.164.12.2.1.2.1.3.1.4

Gauge32

read-only

The counter associated with the number of received cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalGcra0Violations

1.3.6.1.4.1.164.12.2.1.2.1.3.1.5

Gauge32

read-only

The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalGcra1Violations

1.3.6.1.4.1.164.12.2.1.2.1.3.1.6

Gauge32

read-only

The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalRxAIS

1.3.6.1.4.1.164.12.2.1.2.1.3.1.7

Gauge32

read-only

The counter associated with the number of received AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalTxAIS

1.3.6.1.4.1.164.12.2.1.2.1.3.1.8

Gauge32

read-only

The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.

G32 atmVpIntervalRxRDI

1.3.6.1.4.1.164.12.2.1.2.1.3.1.9

Gauge32

read-only

The counter associated with the number of received RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalTxRDI

1.3.6.1.4.1.164.12.2.1.2.1.3.1.10

Gauge32

read-only

The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalContinuityLoss

1.3.6.1.4.1.164.12.2.1.2.1.3.1.11

Gauge32

read-only

The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalUAS

1.3.6.1.4.1.164.12.2.1.2.1.3.1.12

Gauge32

read-only

The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalSES

1.3.6.1.4.1.164.12.2.1.2.1.3.1.13

Gauge32

read-only

The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalCDC

1.3.6.1.4.1.164.12.2.1.2.1.3.1.14

Gauge32

read-only

Amount of cells dropped in the 15 minute interval of the VP connection.

G32 atmVpIntervalTotalDiscards

1.3.6.1.4.1.164.12.2.1.2.1.3.1.15

Gauge32

read-only

The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.

G32 atmVpIntervalClp0Discards

1.3.6.1.4.1.164.12.2.1.2.1.3.1.16

Gauge32

read-only

The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.

G32 atmVpIntervalTotalCellOuts

1.3.6.1.4.1.164.12.2.1.2.1.3.1.17

Gauge32

read-only

The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.

G32 atmVpIntervalClp0CellOuts

1.3.6.1.4.1.164.12.2.1.2.1.3.1.18

Gauge32

read-only

The total number of valid ATM cells transmitted with CLP=0 by this VPL.

G32 atmVpIntervalTaggedOuts

1.3.6.1.4.1.164.12.2.1.2.1.3.1.19

Gauge32

read-only

The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.

G32 atmVpIntervalPCR

1.3.6.1.4.1.164.12.2.1.2.1.3.1.20

Gauge32

read-only

The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalSCR

1.3.6.1.4.1.164.12.2.1.2.1.3.1.21

Gauge32

read-only

The average traffic rate during the last interval of the VP connection , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalMCR

1.3.6.1.4.1.164.12.2.1.2.1.3.1.22

Gauge32

read-only

MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpIntervalShaperTotalDiscards

1.3.6.1.4.1.164.12.2.1.2.1.3.1.23

Gauge32

read-only

The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.

G32 atmVpIntervalShaperClp0Discards

1.3.6.1.4.1.164.12.2.1.2.1.3.1.24

Gauge32

read-only

The total number of CLP0 cells discarded due to congestion by the traffic shaper.

G32 atmVpIntervalShaperClp1Discards

1.3.6.1.4.1.164.12.2.1.2.1.3.1.25

Gauge32

read-only

The total number of CLP1 cells discarded due to congestion by the traffic shaper.

atmVpPMIntervalTable

1.3.6.1.4.1.164.12.2.1.2.1.4

not-accessible

The ATM Vp Interval table for Performance Management.

atmVpPMIntervalEntry

1.3.6.1.4.1.164.12.2.1.2.1.4.1

not-accessible

An entry in the ATM Vp Interval table for Performance Management.

I32 atmVpPMIntervalVpi

1.3.6.1.4.1.164.12.2.1.2.1.4.1.1

Integer32

read-only

The VPI of the VPL.

INT atmVpPMIntervalDir

1.3.6.1.4.1.164.12.2.1.2.1.4.1.2

INTEGER

read-only

The direction of performance management.

I32 atmVpPMIntervalNumber

1.3.6.1.4.1.164.12.2.1.2.1.4.1.3

Integer32

read-only

A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).

G32 atmVpPMIntervalTxClp01

1.3.6.1.4.1.164.12.2.1.2.1.4.1.4

Gauge32

read-only

The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalTxClp0

1.3.6.1.4.1.164.12.2.1.2.1.4.1.5

Gauge32

read-only

The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalRxClp01

1.3.6.1.4.1.164.12.2.1.2.1.4.1.6

Gauge32

read-only

The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalRxClp0

1.3.6.1.4.1.164.12.2.1.2.1.4.1.7

Gauge32

read-only

The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalErroredCells

1.3.6.1.4.1.164.12.2.1.2.1.4.1.8

Gauge32

read-only

The counter associated with the number of Errored cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalLostCells

1.3.6.1.4.1.164.12.2.1.2.1.4.1.9

Gauge32

read-only

The counter associated with the number of Lost cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalMisinsertedCells

1.3.6.1.4.1.164.12.2.1.2.1.4.1.10

Gauge32

read-only

The counter associated with the number of Misinserted cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalECB

1.3.6.1.4.1.164.12.2.1.2.1.4.1.11

Gauge32

read-only

The counter associated with the number of ECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalSECB

1.3.6.1.4.1.164.12.2.1.2.1.4.1.12

Gauge32

read-only

The counter associated with the number of SECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalES

1.3.6.1.4.1.164.12.2.1.2.1.4.1.13

Gauge32

read-only

The counter associated with the number of Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalSES

1.3.6.1.4.1.164.12.2.1.2.1.4.1.14

Gauge32

read-only

The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

G32 atmVpPMIntervalUAS

1.3.6.1.4.1.164.12.2.1.2.1.4.1.15

Gauge32

read-only

The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.

INT atmVpPMIntervalQuality

1.3.6.1.4.1.164.12.2.1.2.1.4.1.16

INTEGER

read-only

If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.

INT atmVpPMIntervalLastDayQuality

1.3.6.1.4.1.164.12.2.1.2.1.4.1.17

INTEGER

read-only

If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.

atmVpQoSTable

1.3.6.1.4.1.164.12.2.1.2.1.5

not-accessible

The VP QoS table.

atmVpQoSEntry

1.3.6.1.4.1.164.12.2.1.2.1.5.1

not-accessible

.

INT atmVpQoSPeriodRef

1.3.6.1.4.1.164.12.2.1.2.1.5.1.1

INTEGER

read-only

This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.

I32 atmVpQoSElapsedTime

1.3.6.1.4.1.164.12.2.1.2.1.5.1.2

Integer32

read-only

Elapsed Time in seconds. - for atmVpQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVpQoSPeriodRef = lastPeriod: The value of atmVpQoSElapsedTime when last systemResetAllStatsCmd was received.

G32 atmVpQoSUAS

1.3.6.1.4.1.164.12.2.1.2.1.5.1.3

Gauge32

read-only

Number of Unavailable Seconds for the reference period (atmVpQoSPeriodRef).

atmVpPMQoSTable

1.3.6.1.4.1.164.12.2.1.2.1.6

not-accessible

The PM VP QoS table.

atmVpPMQoSEntry

1.3.6.1.4.1.164.12.2.1.2.1.6.1

not-accessible

.

INT atmVpPMQoSDirection

1.3.6.1.4.1.164.12.2.1.2.1.6.1.1

INTEGER

read-only

The direction of performance management.

INT atmVpPMQoSPeriodRef

1.3.6.1.4.1.164.12.2.1.2.1.6.1.2

INTEGER

read-only

This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.

G32 atmVpPMQoSCLR

1.3.6.1.4.1.164.12.2.1.2.1.6.1.3

Gauge32

read-only

Cell Loss Ratio counter for the reference period (atmVpPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.

G32 atmVpPMQoSCER

1.3.6.1.4.1.164.12.2.1.2.1.6.1.4

Gauge32

read-only

Cell Error Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.

G32 atmVpPMQoSCMR

1.3.6.1.4.1.164.12.2.1.2.1.6.1.5

Gauge32

read-only

Cell Misinsertion Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .

atmVpShaperStatTable

1.3.6.1.4.1.164.12.2.1.2.1.7

not-accessible

The ATM VP shaper statistics table.

atmVpShaperStatEntry

1.3.6.1.4.1.164.12.2.1.2.1.7.1

not-accessible

An entry in the ATM VP shaper statistics table.

C32 atmVpShaperDiscarded

1.3.6.1.4.1.164.12.2.1.2.1.7.1.1

Counter32

read-only

The number of Cells that were discarded in the shaper on that VPC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.

I32 atmVpShaperOccupation

1.3.6.1.4.1.164.12.2.1.2.1.7.1.2

Integer32

read-only

The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.

I32 atmVpShaperMaxOccupation

1.3.6.1.4.1.164.12.2.1.2.1.7.1.3

Integer32

read-only

The Maximum number of Cells that were stored in the buffer, since this VP was activated. This parameter is limited to 20 bits.

INT atmVpShaperLevel

1.3.6.1.4.1.164.12.2.1.2.1.7.1.4

INTEGER

read-only

The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VPC.

C32 atmVpShaperEpdDropped

1.3.6.1.4.1.164.12.2.1.2.1.7.1.5

Counter32

read-only

The number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VP only.

C32 atmVpShaperTotalEpdDropped

1.3.6.1.4.1.164.12.2.1.2.1.7.1.6

Counter32

read-only

The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VP only.

atmVcPerformance

1.3.6.1.4.1.164.12.2.1.2.2

atmVcCurrentTable

1.3.6.1.4.1.164.12.2.1.2.2.1

not-accessible

The ATM VC Current table.

atmVcCurrentEntry

1.3.6.1.4.1.164.12.2.1.2.2.1.1

not-accessible

An entry in the ATM VC Current table.

I32 atmVcCurrentVpi

1.3.6.1.4.1.164.12.2.1.2.2.1.1.1

Integer32

read-only

The VPI of the VCL.

I32 atmVcCurrentVci

1.3.6.1.4.1.164.12.2.1.2.2.1.1.2

Integer32

read-only

The VCI of the VCL.

G32 atmVcCurrentRxCellsClp01

1.3.6.1.4.1.164.12.2.1.2.2.1.1.3

Gauge32

read-only

The counter associated with the number of transmitted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentRxCellsClp0

1.3.6.1.4.1.164.12.2.1.2.2.1.1.4

Gauge32

read-only

The counter associated with the number of received cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentGcra0Violations

1.3.6.1.4.1.164.12.2.1.2.2.1.1.5

Gauge32

read-only

The counter associated with the number of cells violating GCRA0, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentGcra1Violations

1.3.6.1.4.1.164.12.2.1.2.2.1.1.6

Gauge32

read-only

The counter associated with the number of cells violating GCRA1, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentRxAIS

1.3.6.1.4.1.164.12.2.1.2.2.1.1.7

Gauge32

read-only

The counter associated with the number of received AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentTxAIS

1.3.6.1.4.1.164.12.2.1.2.2.1.1.8

Gauge32

read-only

The counter associated with the number of transmitted AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.

G32 atmVcCurrentRxRDI

1.3.6.1.4.1.164.12.2.1.2.2.1.1.9

Gauge32

read-only

The counter associated with the number of received RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentTxRDI

1.3.6.1.4.1.164.12.2.1.2.2.1.1.10

Gauge32

read-only

The counter associated with the number of transmitted RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentContinuityLoss

1.3.6.1.4.1.164.12.2.1.2.2.1.1.11

Gauge32

read-only

The counter associated with the number of loss of continuity cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentUAS

1.3.6.1.4.1.164.12.2.1.2.2.1.1.12

Gauge32

read-only

The counter associated with the number of Unavailable Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentSES

1.3.6.1.4.1.164.12.2.1.2.2.1.1.13

Gauge32

read-only

The counter associated with the number of Severerly Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcCurrentCDC

1.3.6.1.4.1.164.12.2.1.2.2.1.1.14

Gauge32

read-only

Amount of cells dropped in the current 15 minute interval of the VC connection.

G32 atmVcCurrentTotalDiscards

1.3.6.1.4.1.164.12.2.1.2.2.1.1.15

Gauge32

read-only

The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.

G32 atmVcCurrentClp0Discards

1.3.6.1.4.1.164.12.2.1.2.2.1.1.16

Gauge32

read-only

The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.

G32 atmVcCurrentTotalCellOuts

1.3.6.1.4.1.164.12.2.1.2.2.1.1.17

Gauge32

read-only

The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.

G32 atmVcCurrentClp0CellOuts

1.3.6.1.4.1.164.12.2.1.2.2.1.1.18

Gauge32

read-only

The total number of valid ATM cells transmitted with CLP=0 by this VPL.

G32 atmVcCurrentTaggedOuts

1.3.6.1.4.1.164.12.2.1.2.2.1.1.19

Gauge32

read-only

The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.

G32 atmVcCurrentPCR

1.3.6.1.4.1.164.12.2.1.2.2.1.1.20

Gauge32

read-only

The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second).

G32 atmVcCurrentSCR

1.3.6.1.4.1.164.12.2.1.2.2.1.1.21

Gauge32

read-only

The average traffic rate during the last interval of the VC connection.

G32 atmVcCurrentMCR

1.3.6.1.4.1.164.12.2.1.2.2.1.1.22

Gauge32

read-only

MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second).

G32 atmVcCurrentShaperTotalDiscards

1.3.6.1.4.1.164.12.2.1.2.2.1.1.23

Gauge32

read-only

The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.

G32 atmVcCurrentShaperClp0Discards

1.3.6.1.4.1.164.12.2.1.2.2.1.1.24

Gauge32

read-only

The total number of CLP0 cells discarded due to congestion by the traffic shaper.

G32 atmVcCurrentShaperClp1Discards

1.3.6.1.4.1.164.12.2.1.2.2.1.1.25

Gauge32

read-only

The total number of CLP1 cells discarded due to congestion by the traffic shaper.

atmVcPMCurrentTable

1.3.6.1.4.1.164.12.2.1.2.2.2

not-accessible

The ATM VC Current table for Performance Management.

atmVcPMCurrentEntry

1.3.6.1.4.1.164.12.2.1.2.2.2.1

not-accessible

An entry in the ATM VC Current table for Performance Management.

I32 atmVcPMCurrentVpi

1.3.6.1.4.1.164.12.2.1.2.2.2.1.1

Integer32

read-only

The VPI of the VCL.

I32 atmVcPMCurrentVci

1.3.6.1.4.1.164.12.2.1.2.2.2.1.2

Integer32

read-only

The VCI of the VCL.

I32 atmVcPMCurrentDir

1.3.6.1.4.1.164.12.2.1.2.2.2.1.3

Integer32

read-only

The direction of Performance Management.

G32 atmVcPMCurrentTxClp01

1.3.6.1.4.1.164.12.2.1.2.2.2.1.4

Gauge32

read-only

The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentTxClp0

1.3.6.1.4.1.164.12.2.1.2.2.2.1.5

Gauge32

read-only

The counter associated with the number of transmitted CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentRxClp01

1.3.6.1.4.1.164.12.2.1.2.2.2.1.6

Gauge32

read-only

The counter associated with the number of received CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentRxClp0

1.3.6.1.4.1.164.12.2.1.2.2.2.1.7

Gauge32

read-only

The counter associated with the number of received CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentErroredCells

1.3.6.1.4.1.164.12.2.1.2.2.2.1.8

Gauge32

read-only

The counter associated with the number of errored cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentLostCells

1.3.6.1.4.1.164.12.2.1.2.2.2.1.9

Gauge32

read-only

The counter associated with the number of lost cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentMisinsertedCells

1.3.6.1.4.1.164.12.2.1.2.2.2.1.10

Gauge32

read-only

The counter associated with the number of misinserted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentECB

1.3.6.1.4.1.164.12.2.1.2.2.2.1.11

Gauge32

read-only

The counter associated with the number of ECBs encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentSECB

1.3.6.1.4.1.164.12.2.1.2.2.2.1.12

Gauge32

read-only

The counter associated with the number of SECBs encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentES

1.3.6.1.4.1.164.12.2.1.2.2.2.1.13

Gauge32

read-only

The counter associated with the number of Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentSES

1.3.6.1.4.1.164.12.2.1.2.2.2.1.14

Gauge32

read-only

The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.

G32 atmVcPMCurrentUAS

1.3.6.1.4.1.164.12.2.1.2.2.2.1.15

Gauge32

read-only

The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.

INT atmVcPMCurrentIntervalQuality

1.3.6.1.4.1.164.12.2.1.2.2.2.1.16

INTEGER

read-only

If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.

INT atmVcPMCurrentLastDayQuality

1.3.6.1.4.1.164.12.2.1.2.2.2.1.17

INTEGER

read-only

If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.

atmVcIntervalTable

1.3.6.1.4.1.164.12.2.1.2.2.3

not-accessible

The ATM Vc Interval table.

atmVcIntervalEntry

1.3.6.1.4.1.164.12.2.1.2.2.3.1

not-accessible

An entry in the ATM Vc Interval table.

I32 atmVcIntervalVpi

1.3.6.1.4.1.164.12.2.1.2.2.3.1.1

Integer32

read-only

The VPI of the VCL.

I32 atmVcIntervalVci

1.3.6.1.4.1.164.12.2.1.2.2.3.1.2

Integer32

read-only

The VCI of the VCL.

I32 atmVcIntervalNumber

1.3.6.1.4.1.164.12.2.1.2.2.3.1.3

Integer32

read-only

A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).

G32 atmVcIntervalRxCellsClp01

1.3.6.1.4.1.164.12.2.1.2.2.3.1.4

Gauge32

read-only

The counter associated with the number of transmitted cells , encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalRxCellsClp0

1.3.6.1.4.1.164.12.2.1.2.2.3.1.5

Gauge32

read-only

The counter associated with the number of received cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalGcra0Violations

1.3.6.1.4.1.164.12.2.1.2.2.3.1.6

Gauge32

read-only

The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalGcra1Violations

1.3.6.1.4.1.164.12.2.1.2.2.3.1.7

Gauge32

read-only

The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalRxAIS

1.3.6.1.4.1.164.12.2.1.2.2.3.1.8

Gauge32

read-only

The counter associated with the number of received AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalTxAIS

1.3.6.1.4.1.164.12.2.1.2.2.3.1.9

Gauge32

read-only

The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.

G32 atmVcIntervalRxRDI

1.3.6.1.4.1.164.12.2.1.2.2.3.1.10

Gauge32

read-only

The counter associated with the number of received RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalTxRDI

1.3.6.1.4.1.164.12.2.1.2.2.3.1.11

Gauge32

read-only

The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalContinuityLoss

1.3.6.1.4.1.164.12.2.1.2.2.3.1.12

Gauge32

read-only

The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalUAS

1.3.6.1.4.1.164.12.2.1.2.2.3.1.13

Gauge32

read-only

The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalSES

1.3.6.1.4.1.164.12.2.1.2.2.3.1.14

Gauge32

read-only

The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalCDC

1.3.6.1.4.1.164.12.2.1.2.2.3.1.15

Gauge32

read-only

Amount of cells dropped in the 15 minute interval of the VC connection.

G32 atmVcIntervalTotalDiscards

1.3.6.1.4.1.164.12.2.1.2.2.3.1.16

Gauge32

read-only

The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.

G32 atmVcIntervalClp0Discards

1.3.6.1.4.1.164.12.2.1.2.2.3.1.17

Gauge32

read-only

The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.

G32 atmVcIntervalTotalCellOuts

1.3.6.1.4.1.164.12.2.1.2.2.3.1.18

Gauge32

read-only

The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.

G32 atmVcIntervalClp0CellOuts

1.3.6.1.4.1.164.12.2.1.2.2.3.1.19

Gauge32

read-only

The total number of valid ATM cells transmitted with CLP=0 by this VPL.

G32 atmVcIntervalTaggedOuts

1.3.6.1.4.1.164.12.2.1.2.2.3.1.20

Gauge32

read-only

The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.

G32 atmVcIntervalPCR

1.3.6.1.4.1.164.12.2.1.2.2.3.1.21

Gauge32

read-only

The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalSCR

1.3.6.1.4.1.164.12.2.1.2.2.3.1.22

Gauge32

read-only

The average traffic rate during the last interval of the VC connection, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalMCR

1.3.6.1.4.1.164.12.2.1.2.2.3.1.23

Gauge32

read-only

MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcIntervalShaperTotalDiscards

1.3.6.1.4.1.164.12.2.1.2.2.3.1.24

Gauge32

read-only

The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.

G32 atmVcIntervalShaperClp0Discards

1.3.6.1.4.1.164.12.2.1.2.2.3.1.25

Gauge32

read-only

The total number of CLP0 cells discarded due to congestion by the traffic shaper.

G32 atmVcIntervalShaperClp1Discards

1.3.6.1.4.1.164.12.2.1.2.2.3.1.26

Gauge32

read-only

The total number of CLP1 cells discarded due to congestion by the traffic shaper.

atmVcPMIntervalTable

1.3.6.1.4.1.164.12.2.1.2.2.4

not-accessible

The ATM Vc Interval table for Performance Management.

atmVcPMIntervalEntry

1.3.6.1.4.1.164.12.2.1.2.2.4.1

not-accessible

An entry in the ATM Vc Interval table for Performance Management.

I32 atmVcPMIntervalVpi

1.3.6.1.4.1.164.12.2.1.2.2.4.1.1

Integer32

read-only

The VPI of the VCL.

I32 atmVcPMIntervalVci

1.3.6.1.4.1.164.12.2.1.2.2.4.1.2

Integer32

read-only

The VCI of the VCL.

INT atmVcPMIntervalDir

1.3.6.1.4.1.164.12.2.1.2.2.4.1.3

INTEGER

read-only

The direction of Performance Management.

I32 atmVcPMIntervalNumber

1.3.6.1.4.1.164.12.2.1.2.2.4.1.4

Integer32

read-only

A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).

G32 atmVcPMIntervalTxClp01

1.3.6.1.4.1.164.12.2.1.2.2.4.1.5

Gauge32

read-only

The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalTxClp0

1.3.6.1.4.1.164.12.2.1.2.2.4.1.6

Gauge32

read-only

The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalRxClp01

1.3.6.1.4.1.164.12.2.1.2.2.4.1.7

Gauge32

read-only

The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalRxClp0

1.3.6.1.4.1.164.12.2.1.2.2.4.1.8

Gauge32

read-only

The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalErroredCells

1.3.6.1.4.1.164.12.2.1.2.2.4.1.9

Gauge32

read-only

The counter associated with the number of Errored cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalLostCells

1.3.6.1.4.1.164.12.2.1.2.2.4.1.10

Gauge32

read-only

The counter associated with the number of Lost cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalMisinsertedCells

1.3.6.1.4.1.164.12.2.1.2.2.4.1.11

Gauge32

read-only

The counter associated with the number of Misinserted cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalECB

1.3.6.1.4.1.164.12.2.1.2.2.4.1.12

Gauge32

read-only

The counter associated with the number of ECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalSECB

1.3.6.1.4.1.164.12.2.1.2.2.4.1.13

Gauge32

read-only

The counter associated with the number of SECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalES

1.3.6.1.4.1.164.12.2.1.2.2.4.1.14

Gauge32

read-only

The counter associated with the number of Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalSES

1.3.6.1.4.1.164.12.2.1.2.2.4.1.15

Gauge32

read-only

The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

G32 atmVcPMIntervalUAS

1.3.6.1.4.1.164.12.2.1.2.2.4.1.16

Gauge32

read-only

The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.

INT atmVcPMIntervalQuality

1.3.6.1.4.1.164.12.2.1.2.2.4.1.17

INTEGER

read-only

If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.

INT atmVcPMIntervalLastDayQuality

1.3.6.1.4.1.164.12.2.1.2.2.4.1.18

INTEGER

read-only

If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.

atmVcQoSTable

1.3.6.1.4.1.164.12.2.1.2.2.6

not-accessible

The ATM VP QoS table.

atmVcQoSEntry

1.3.6.1.4.1.164.12.2.1.2.2.6.1

not-accessible

An entry in the ATM VP table.

INT atmVcQoSPeriodRef

1.3.6.1.4.1.164.12.2.1.2.2.6.1.1

INTEGER

read-only

This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.

I32 atmVcQoSElapsedTime

1.3.6.1.4.1.164.12.2.1.2.2.6.1.2

Integer32

read-only

Elapsed Time in seconds. - for atmVcQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVcQoSPeriodRef = lastPeriod: The value of atmVcQoSElapsedTime when last systemResetAllStatsCmd was received.

G32 atmVcQoSUAS

1.3.6.1.4.1.164.12.2.1.2.2.6.1.3

Gauge32

read-only

Number of Unavailable Seconds for the reference period (atmVcQoSPeriodRef).

atmVcPMQoSTable

1.3.6.1.4.1.164.12.2.1.2.2.7

not-accessible

The PM VC QoS table.

atmVcPMQoSEntry

1.3.6.1.4.1.164.12.2.1.2.2.7.1

not-accessible

An entry in the VC PM QoS table.

INT atmVcPMQoSDirection

1.3.6.1.4.1.164.12.2.1.2.2.7.1.1

INTEGER

read-only

The direction of performance management.

INT atmVcPMQoSPeriodRef

1.3.6.1.4.1.164.12.2.1.2.2.7.1.2

INTEGER

read-only

This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.

G32 atmVcPMQoSCLR

1.3.6.1.4.1.164.12.2.1.2.2.7.1.3

Gauge32

read-only

Cell Loss Ratio counter for the reference period (atmVcPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.

G32 atmVcPMQoSCER

1.3.6.1.4.1.164.12.2.1.2.2.7.1.4

Gauge32

read-only

Cell Error Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.

G32 atmVcPMQoSCMR

1.3.6.1.4.1.164.12.2.1.2.2.7.1.5

Gauge32

read-only

Cell Miss-insertion Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .

atmVcShaperStatTable

1.3.6.1.4.1.164.12.2.1.2.2.8

not-accessible

The ATM VC shaper statistics table.

atmVcShaperStatEntry

1.3.6.1.4.1.164.12.2.1.2.2.8.1

not-accessible

An entry in the ATM VC shaper statistics table.

C32 atmVcShaperDiscarded

1.3.6.1.4.1.164.12.2.1.2.2.8.1.1

Counter32

read-only

The number of Cells that were discarded in the shaper on that VCC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.

I32 atmVcShaperOccupation

1.3.6.1.4.1.164.12.2.1.2.2.8.1.2

Integer32

read-only

The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.

I32 atmVcShaperMaxOccupation

1.3.6.1.4.1.164.12.2.1.2.2.8.1.3

Integer32

read-only

The Maximum number of Cells that were stored in the buffer, since this VC was activated. This parameter is limited to 20 bits.

INT atmVcShaperLevel

1.3.6.1.4.1.164.12.2.1.2.2.8.1.4

INTEGER

read-only

The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VCC.

C32 atmVcShaperEpdDropped

1.3.6.1.4.1.164.12.2.1.2.2.8.1.5

Counter32

read-only

The number of Cells that were dropped in the shaper on that VCC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VC only.

C32 atmVcShaperTotalEpdDropped

1.3.6.1.4.1.164.12.2.1.2.2.8.1.6

Counter32

read-only

The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VC only.

atmIntervalDateTable

1.3.6.1.4.1.164.12.2.1.3

not-accessible

The agent will keep in this group the date & time corresponding to each interval.

atmIntervalDateEntry

1.3.6.1.4.1.164.12.2.1.3.1

not-accessible

The date & time for the given interval.

I32 atmIntervalDateInterval

1.3.6.1.4.1.164.12.2.1.3.1.1

Integer32

read-only

The interval number defining this entry.

STR atmIntervalDateDate

1.3.6.1.4.1.164.12.2.1.3.1.2

DisplayString

read-only

The date corresponding to this interval.

STR atmIntervalDateTime

1.3.6.1.4.1.164.12.2.1.3.1.3

DisplayString

read-only

The time corresponding to this interval.

atmGenSystem

1.3.6.1.4.1.164.12.2.2

atmGenSysGen

1.3.6.1.4.1.164.12.2.2.1

atmGenSysSelfTestTable

1.3.6.1.4.1.164.12.2.2.1.1

not-accessible

A table containing the results of the initial testing of the device.

atmGenSysSelfTestEntry

1.3.6.1.4.1.164.12.2.2.1.1.1

not-accessible

An entry in table.

I32 atmGenSysSelfTestIndex

1.3.6.1.4.1.164.12.2.2.1.1.1.1

Integer32

read-only

A running index for the table.

STR atmGenSysSelfTestResult

1.3.6.1.4.1.164.12.2.2.1.1.1.2

DisplayString

read-only

The results of the initial testing of the device.

STR atmGenSysSelfTestModule

1.3.6.1.4.1.164.12.2.2.1.1.1.3

DisplayString

read-only

The name of module on which the test was performed.

INT atmGenSysLogClearAll

1.3.6.1.4.1.164.12.2.2.1.2

INTEGER

read-write

Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).

atmGenSysLogTable

1.3.6.1.4.1.164.12.2.2.1.3

not-accessible

A copy of the log buffer.

atmGenSysLogEntry

1.3.6.1.4.1.164.12.2.2.1.3.1

not-accessible

An entry in table.

I32 atmGenSysLogIndex

1.3.6.1.4.1.164.12.2.2.1.3.1.1

Integer32

read-only

The index of the log buffer.

STR atmGenSysLogMessage

1.3.6.1.4.1.164.12.2.2.1.3.1.2

DisplayString

read-only

The log buffer entry message text.

INT atmGenSysSetDefaultConfg

1.3.6.1.4.1.164.12.2.2.1.4

INTEGER

read-write

When set to on(3), the agent will set all the configuration parameters to their default values. The variable is then reset to off(2) by the agent. The agent must be reset for the default configuration to apply.

atmGenSysCxRefTable

1.3.6.1.4.1.164.12.2.2.1.5

not-accessible

A Cross Reference table. The table maintains an index of an object which is also the table index, and a counter that indicates how many times this object was referenced. When using this table for more than one referenced table, which uses the same range of indexes, then the index should be shifted by a unique offset per table. In ACE2002 this table is used for TD and for FR Desc. Thus, the index for FR Descriptor is: FR Descriptor index + offset. The offset is described in the ACE2002 NMS SRS.

atmGenSysCxRefEntry

1.3.6.1.4.1.164.12.2.2.1.5.1

not-accessible

The entries will be added by the agent upon an entry addition in the referenced tables (TD table, FR Descriptor etc.)

I32 atmGenSysCxRefIndex

1.3.6.1.4.1.164.12.2.2.1.5.1.1

Integer32

read-only

The index specifies an entry in the table of the object.

G32 atmGenSysCxRefCounter

1.3.6.1.4.1.164.12.2.2.1.5.1.2

Gauge32

read-only

The counter counts the number of references that have been made to the object .

atmNte

1.3.6.1.4.1.164.12.3

atmNteEvents

1.3.6.1.4.1.164.12.3.0

The events for RAD ATM products.

NTF atmAceStatusChange

1.3.6.1.4.1.164.12.3.0.1

The trap is sent every time there is a change in the state of one of the LEDs.

NTF atmAceAlarmTrap

1.3.6.1.4.1.164.12.3.0.2

The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm. An active alarm state exists if: 1) The atmInterfaceActiveAlarms vector is different than 0. 2) The atmNteAlarmVpTable contains entries. 3) The atmNteAlarmVcTable contains entries. The trap is also sent when a transition into the no alarm state occurs. The second variable will be atmInterfaceActiveAlarms to indicate the kind of the alarm. The trap is not sent more than once in a 10 second interval.

NTF atmAceModuleChangeTrap

1.3.6.1.4.1.164.12.3.0.3

The trap is sent every time a module is changed (Hot swapping). The second variable will be atmNteCardType to indicate the type of card that was inserted. The value empty(255) indicates that a card was taken out.

NTF atmAceRedundancyTrap

1.3.6.1.4.1.164.12.3.0.4

The trap is sent upon change in link as a result of redundancy. The ifIndex parameter indicates the current active link.

NTF atmAceModuleMismatchTrap

1.3.6.1.4.1.164.12.3.0.5

The trap is sent upon starting or stopping of a module mismatch state. A possible mismatch is when the inserted module is other than the programmed one.

atmNteSys

1.3.6.1.4.1.164.12.3.1

atmNteSysConfig

1.3.6.1.4.1.164.12.3.1.1

atmNteManagerTable

1.3.6.1.4.1.164.12.3.1.1.1

not-accessible

The Manager Table includes all the NMSs that receive traps from this agent. A single manager can receive traps on more than one PVC. The agent will set implicitly the correct ifIndex, VPI, VCI values to all relevant entries in the table when the user changes them for one of the PVCs.

atmNteManagerEntry

1.3.6.1.4.1.164.12.3.1.1.1.1

not-accessible

A single manager and the PVC for receiving traps.

IP atmNteManagerIP

1.3.6.1.4.1.164.12.3.1.1.1.1.1

IpAddress

read-only

The IP address of the NMS.

I32 atmNteManagerPvc

1.3.6.1.4.1.164.12.3.1.1.1.1.2

Integer32

read-only

A PVC index. The range is 1..8. There are four PVCs on the User Port and four PVCs on the Network Port. The default VPI, VCI values are specified below.

I32 atmNteManagerIfIndex

1.3.6.1.4.1.164.12.3.1.1.1.1.3

Integer32

read-create

The ATM interface index of the management port.

I32 atmNteManagerVpi

1.3.6.1.4.1.164.12.3.1.1.1.1.4

Integer32

read-create

The VPI of the management VCL. Default: 0.

I32 atmNteManagerVci

1.3.6.1.4.1.164.12.3.1.1.1.1.5

Integer32

read-create

The VCI of the management VCL. Defaults: 32,33,34,35.

I32 atmNteManagerTrapMask

1.3.6.1.4.1.164.12.3.1.1.1.1.6

Integer32

read-create

The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.

ROW atmNteManagerRowStatus

1.3.6.1.4.1.164.12.3.1.1.1.1.7

RowStatus

read-create

Creation/Deletion of rows in the table.

IP atmNteManagerNextHop

1.3.6.1.4.1.164.12.3.1.1.1.1.8

IpAddress

read-create

This parameter is relevant to Ethernet out of band host only (PVC=10). The Next Hop IP address of the entry route.

INT atmNteManagerVlanSupport

1.3.6.1.4.1.164.12.3.1.1.1.1.9

INTEGER

read-create

VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.

I32 atmNteManagerVlanIdentifier

1.3.6.1.4.1.164.12.3.1.1.1.1.10

Integer32

read-create

VLAN ID. Range is 0..4095.

I32 atmNteManagerVlanFramePriority

1.3.6.1.4.1.164.12.3.1.1.1.1.11

Integer32

read-create

VLAN Frame priority.Range is 0..7.

OCT atmNteManagerAlarmTrapMask

1.3.6.1.4.1.164.12.3.1.1.1.1.12

OCTET STRING

read-create

The value of this object determines the alarm traps that the agent should mask and not send to this NMS. The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. More details on the masked traps exist in the product specification. For products that do not mask specific traps, the value of the bits will be 0.

I32 atmNteManagerConfigPorts

1.3.6.1.4.1.164.12.3.1.1.1.1.13

Integer32

read-create

This variable defines from which port/s this manager can configure the device. For IPmux 11 the value of this variable will be according to the ports combination: Network =1 User1=2 User2=4 (For Example: All ports = 7).

I32 atmNteUPLTCR

1.3.6.1.4.1.164.12.3.1.1.2

Integer32

read-write

The Unacceptable ES Limit threshold for Performance Management.

I32 atmNteDPLTCR

1.3.6.1.4.1.164.12.3.1.1.3

Integer32

read-write

The Degraded ES Limit threshold for Performance Management.

INT atmNteSysLogClearAll

1.3.6.1.4.1.164.12.3.1.1.4

INTEGER

read-write

Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).

I32 atmNteUSESLTCR

1.3.6.1.4.1.164.12.3.1.1.5

Integer32

read-write

The Unacceptable SES Limit threshold for Performance Management.

I32 atmNteDSESLTCR

1.3.6.1.4.1.164.12.3.1.1.6

Integer32

read-write

The Degraded ES Limit threshold for Performance Management.

atmNteProtection

1.3.6.1.4.1.164.12.3.1.1.8

INT atmNteProtectionMode

1.3.6.1.4.1.164.12.3.1.1.8.1

INTEGER

read-write

Protection Mode. MspOn - Multiplex section protection. pathOn - High order path protection. mspUniOn - Multiplex section Uni-directional protection. mspOneToN - Multiplex section protection.

INT atmNteProtectionWorkingLink

1.3.6.1.4.1.164.12.3.1.1.8.2

INTEGER

read-write

Selects the working link when atmNteProtectionMode is off.

INT atmNteProtectionSwitchLink

1.3.6.1.4.1.164.12.3.1.1.8.3

INTEGER

read-write

ForceSwitch - will force Switching from the working link to the backup link. Afterwards the agent will set atmNteProtectionSwitchLink back to off(1). atmNteProtectionMode must be either mspOn or pathOn.

atmNteConfOam

1.3.6.1.4.1.164.12.3.1.1.9

INT atmNteConfOamSupport

1.3.6.1.4.1.164.12.3.1.1.9.1

INTEGER

read-write

OAM support mode, which determines the device location in a segment wise.

atmNteConfOamTransmission

1.3.6.1.4.1.164.12.3.1.1.9.2

INT atmNteConfOamAIS

1.3.6.1.4.1.164.12.3.1.1.9.2.1

INTEGER

read-write

Defines if a F4 segment OAM cell is transmitted due to problems in the other port, i.e. physical layer alarm or F4 defect. This is valid only when the ACE101 has ATM UNI interfaces in both sides and is configured for 'Non-Intrusive' mode. none - AIS is not sent to any of the ports. user - F4 AIS will be sent toward the user when defect is detected in the network port. network - F4 AIS will be sent toward the network when defect is detected in the user port. both - F4 AIS will be sent toward the network when defect is detected in the user port and toward the user when defect is detected in the network port.

INT atmNteConfOamRDI

1.3.6.1.4.1.164.12.3.1.1.9.2.2

INTEGER

read-write

Defines if an F4 OAM RDI cell is transmitted due to physical layer problems in the port (in addition to F4 RDI cells transmitted due to ATM layer problems). The type of F4 RDI (Segment or End-to-End) is according to the ACE-101 OAM mode. For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4 RDI cell back to the trunk.

atmNteConfOamAddressing

1.3.6.1.4.1.164.12.3.1.1.9.3

INT atmNteConfLoopbackAddMode

1.3.6.1.4.1.164.12.3.1.1.9.3.1

INTEGER

read-write

Loopback addressing mode. on - will enable loopback addressing. off - will disable loopback addressing.

OCT atmNteConfLoopbackSourceAdd

1.3.6.1.4.1.164.12.3.1.1.9.3.2

OCTET STRING

read-write

Loopback source address. This field is relevant when atmNteConfOamAddMode is on.

atmNteConfOamIfTable

1.3.6.1.4.1.164.12.3.1.1.9.4

not-accessible

OAM support per ATM interface.

atmNteConfOamIfEntry

1.3.6.1.4.1.164.12.3.1.1.9.4.1

not-accessible

.

INT atmNteConfOamIfAisRdi

1.3.6.1.4.1.164.12.3.1.1.9.4.1.1

INTEGER

read-write

This parameter controls the generation of F4/F5 AIS and RDI due to lower order problems such as physical layer problems. For AIS: Defines if F4/F5 AIS cell is transmitted due to problems such as physical layer alarm or F4/F5 defect. This is applicable for all ports . off - Problems in this port will not trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. on - Problems in this port will trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. For RDI: Defines if F4/F5 RDI cell will be transmitted due to physical layer problems in that port (in addition to F4/F5 RDI cells transmitted due to ATM layer problems). For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4/F5 RDI cell back to the trunk. The type of F4/F5 (Segment or End-to-End) is according to the configuration of the VPC/VCC.

atmNteConfCAC

1.3.6.1.4.1.164.12.3.1.1.10

INT atmNteConfCACMode

1.3.6.1.4.1.164.12.3.1.1.10.1

INTEGER

read-write

CAC support mode. For ACE2002, the following are the applicable values: disable(1), enable(2), 10 - 1000.

atmNteHostIfTable

1.3.6.1.4.1.164.12.3.1.1.11

not-accessible

Host IP interface table.

atmNteHostIfEntry

1.3.6.1.4.1.164.12.3.1.1.11.1

not-accessible

.

I32 atmNteHostPvcIndex

1.3.6.1.4.1.164.12.3.1.1.11.1.1

Integer32

read-only

A PVC index. The range is 1..10.

IP atmNteHostIP

1.3.6.1.4.1.164.12.3.1.1.11.1.2

IpAddress

read-create

The host interface IP address.

IP atmNteHostMask

1.3.6.1.4.1.164.12.3.1.1.11.1.3

IpAddress

read-create

The host interface subnet mask.

I32 atmNteHostAtmIfIndex

1.3.6.1.4.1.164.12.3.1.1.11.1.4

Integer32

read-create

ATM interface index. Will be 1 for user port, and 2 for network port.

I32 atmNteHostVpi

1.3.6.1.4.1.164.12.3.1.1.11.1.5

Integer32

read-create

VPI of the PVC connected to that host interface.

I32 atmNteHostVci

1.3.6.1.4.1.164.12.3.1.1.11.1.6

Integer32

read-create

VCI of the PVC connected to that host interface.

ROW atmNteHostRowStatus

1.3.6.1.4.1.164.12.3.1.1.11.1.7

RowStatus

read-create

Creation/Deletion of rows in the table.

I32 atmNteHostRdnVpi

1.3.6.1.4.1.164.12.3.1.1.11.1.8

Integer32

read-create

The VPI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).

I32 atmNteHostRdnVci

1.3.6.1.4.1.164.12.3.1.1.11.1.9

Integer32

read-create

The VCI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).

IP atmNteHostDefaultNextHop

1.3.6.1.4.1.164.12.3.1.1.11.1.10

IpAddress

read-create

The host interface Default Next Hop address. This address will be used as default next hop for every Bundle mapped to this Host.

INT atmNteHostVlanTagging

1.3.6.1.4.1.164.12.3.1.1.11.1.11

INTEGER

read-create

VLAN Tag support. no - No support to VLAN. yes - 4 VLAN bytes will be added to each frame connected to this Host.

I32 atmNteHostDefaultVlanID

1.3.6.1.4.1.164.12.3.1.1.11.1.12

Integer32

read-create

Default VLAN ID of this Host.

I32 atmNteHostDefaultVlanPriority

1.3.6.1.4.1.164.12.3.1.1.11.1.13

Integer32

read-create

Default VLAN priority for this Host.

INT atmNteShaperMode

1.3.6.1.4.1.164.12.3.1.1.12

INTEGER

read-write

Shaper Mode. vpInbandMng - Vcc within a Vp for management.

I32 atmNteOutputRate

1.3.6.1.4.1.164.12.3.1.1.13

Integer32

read-write

Aggregate shaping output rate in Cells per Seconds units. Default value is the Network port rate.

INT atmNteTosMode

1.3.6.1.4.1.164.12.3.1.1.14

INTEGER

read-write

TOS Mode.

OCT atmNteTosMask

1.3.6.1.4.1.164.12.3.1.1.15

OCTET STRING

read-write

This parameter determines the seqence of bits that will be used for TOS. For ACE101 this parameter is applicable only if atmNteTosMode = enable. Valid only for IP-TOS process.

OCT atmNteTosHighPriority

1.3.6.1.4.1.164.12.3.1.1.16

OCTET STRING

read-write

Priorities options are High or Low. High priority will be represented by bit = 1. Low priority will be represented by bit = 0. Each TOS value will be represented by the bit location. For example, the string for TOS 2, 9, 15 with High priority, will be: |0000 0000|... ...|0000 0000|1000 0010|0000 0100| ...98 7654 3210 (Bit #) 8 ... 3 2 1 (Byte #).

INT atmNtePlugAndPlayActivity

1.3.6.1.4.1.164.12.3.1.1.17

INTEGER

read-write

Activity control for Manager Plug And Play. disable - disable the feature. offline - Automatic learn IP address into offline memory. online - Automatic learn IP address into online memory.

INT atmNteSlotUsage

1.3.6.1.4.1.164.12.3.1.1.18

INTEGER

read-write

Applicable to ace2002. Slot 2 might be configured as user slot or as network slot.

INT atmNteConnectionsMaxNumber

1.3.6.1.4.1.164.12.3.1.1.19

INTEGER

read-write

The MAX number of connections supported by system. Setting this parameter will affect the number of MAX intervals supported. This parameter will affect the system only after reset. Changing this parameter from high value to a low value, will be accepted by agent only if the actual used connection <= the desired connection Max number. Applicable to ace2002.

I32 atmNteDefaultVpi

1.3.6.1.4.1.164.12.3.1.1.20

Integer32

read-write

Default Vpi for management.

I32 atmNteDefaultVci

1.3.6.1.4.1.164.12.3.1.1.21

Integer32

read-write

Default Vci for management.

I32 atmNteReservedVpi

1.3.6.1.4.1.164.12.3.1.1.22

Integer32

read-write

Internal use VPI, where shaperMode=vpInbandMng.

INT atmNteRdnManagement

1.3.6.1.4.1.164.12.3.1.1.23

INTEGER

read-only

The redundancy management status.

NUM atmNtePlugAndPlayIfIndex

1.3.6.1.4.1.164.12.3.1.1.24

InterfaceIndex

read-write

The ifIndex of the Plug and Play VCC.

I32 atmNteLoopbackTimeout

1.3.6.1.4.1.164.12.3.1.1.25

Integer32

read-write

The Loopback state timeout in minutes. A value of zero means no timeout (for ever). Default is 5 min.

atmNteOamTable

1.3.6.1.4.1.164.12.3.1.1.26

not-accessible

This table is a static table, which is created by agent once upon initialization. The created entries are actually, only the supported OAM features. This table enables addition of new features by adding new entries rather than adding scalar parameters. An OAM feature is defined by the indexes values combination.

atmNteOamEntry

1.3.6.1.4.1.164.12.3.1.1.26.1

not-accessible

An entry in the OAM table. Each entry in this table will indicate a special OAM.

INT atmNteOamMode

1.3.6.1.4.1.164.12.3.1.1.26.1.1

INTEGER

read-only

The OAM cell path. endToEnd(1) - the entire path.

INT atmNteOamCellType

1.3.6.1.4.1.164.12.3.1.1.26.1.2

INTEGER

read-only

This object indicates a unique Indication Signal. aisAndRdi(1) - Alarm Indication Signal (AIS) and Remote Defect Indication (RDI) cell. loopback(2) - Loopback cell.

INT atmNteOamLevel

1.3.6.1.4.1.164.12.3.1.1.26.1.3

INTEGER

read-only

The level of the OAM cell. -- f4 (2) - VP level, f5 (3) - VC level.

INT atmNteOamEnable

1.3.6.1.4.1.164.12.3.1.1.26.1.4

INTEGER

read-write

This parameter determines if the specified OAM cells will be enabled.

I32 atmNteDefaultLoopbackThreshold

1.3.6.1.4.1.164.12.3.1.1.27

Integer32

read-write

The Default OAM Loopback Failure Threshold value that will be used for configuration.

I32 atmNteMaxBurstSize

1.3.6.1.4.1.164.12.3.1.1.28

Integer32

read-write

The Maximum allowed burst size (cell units). This object is applicable for each Physical port.

I32 atmNteGranularityFactor

1.3.6.1.4.1.164.12.3.1.1.29

Integer32

read-write

This parameter affects the granularity of the guaranteed Rate (SCR+MCR) in spaced connection (cell/sec units). It is also defines the minimum guaranteed rate in spaced connection.

I32 atmNteTotalInputRate

1.3.6.1.4.1.164.12.3.1.1.30

Integer32

read-only

This parameter indicates the total input rate of the device in cells/sec.

I32 atmNteTotalOutputRate

1.3.6.1.4.1.164.12.3.1.1.31

Integer32

read-only

This parameter indicates the total output rate of the device in cells/sec.

atmAlarmForwardingTable

1.3.6.1.4.1.164.12.3.1.1.32

not-accessible

The Alarm Forwarding Mechanism will be operated for this table entries.

atmAlarmForwardingEntry

1.3.6.1.4.1.164.12.3.1.1.32.1

not-accessible

Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.

I32 atmAlarmForwardingFailPort

1.3.6.1.4.1.164.12.3.1.1.32.1.1

Integer32

not-accessible

An Index of the port on which a fail occurs.

I32 atmAlarmForwardingToPort

1.3.6.1.4.1.164.12.3.1.1.32.1.2

Integer32

not-accessible

An Index of the port that will be affected upon the failure of the atmAlarmForwardingFailPort.

ROW atmAlarmForwardingRowStatus

1.3.6.1.4.1.164.12.3.1.1.32.1.3

RowStatus

read-create

Creation/Deletion of rows in the table.

BIT atmAlarmForwardingFailureLevel

1.3.6.1.4.1.164.12.3.1.1.32.1.4

Bits

read-create

This parameter determines the level of failure that will operate the Alarm Forwarding Mechanism.

INT atmAlarmForwardingRecoveryMode

1.3.6.1.4.1.164.12.3.1.1.32.1.5

INTEGER

read-create

This parameter determines the Recovery Mode. manual - The user should stop the RDI transmission by using the atmAlarmForwardingRecoveryCommand. automatic - The RDI transmission will be automatically stopped upon atmAlarmForwardingFailPort recovery.

INT atmAlarmForwardingRecoveryCommand

1.3.6.1.4.1.164.12.3.1.1.32.1.6

INTEGER

read-create

This parameter is a command. It is applicable when atmAlarmForwardingRecoveryMode = manual. on - Will stop the RDI transmission. After setting to 'On' the agent will set this parameter back to 'Off'.

U32 atmAlarmForwardingTimeFilterWindow

1.3.6.1.4.1.164.12.3.1.1.32.1.7

Unsigned32

read-create

This parameter determines the Time Filter Window, meaning: how much time (in seconds) should the alarm exist in order to start the Alarm Forwarding operation.

atmSysConfigCellTest

1.3.6.1.4.1.164.12.3.1.1.33

NUM atmSysConfigCellTestPort

1.3.6.1.4.1.164.12.3.1.1.33.1

InterfaceIndex

read-write

An Index of the port on which the cell test will be sent.

I32 atmSysConfigCellTestVpi

1.3.6.1.4.1.164.12.3.1.1.33.2

Integer32

read-write

The VPI on which the cell test will be sent.

I32 atmSysConfigCellTestVci

1.3.6.1.4.1.164.12.3.1.1.33.3

Integer32

read-write

The VCI on which the cell test will be sent.

INT atmSysConfigCellTestPti

1.3.6.1.4.1.164.12.3.1.1.33.4

INTEGER

read-write

The cell type.

INT atmSysConfigCellTestClp

1.3.6.1.4.1.164.12.3.1.1.33.5

INTEGER

read-write

The type of the Cell.

INT atmSysConfigCellTestOamType

1.3.6.1.4.1.164.12.3.1.1.33.6

INTEGER

read-write

The OAM type of the Cell. This object is applicable if atmSysConfigCellTestPti = oamSegment/oamEndToEnd .

OCT atmSysConfigCellTestPayload

1.3.6.1.4.1.164.12.3.1.1.33.7

OCTET STRING

read-write

The payload of the cell. For OAM cell the payload is set automatically to 6A.

I32 atmSysConfigCellTestQuantity

1.3.6.1.4.1.164.12.3.1.1.33.8

Integer32

read-write

Quantity of cells to send.

INT atmSysConfigCellTestSendCmd

1.3.6.1.4.1.164.12.3.1.1.33.9

INTEGER

read-write

Setting the variable to send(3) perfroms cell test. The agent will immediately reset the variable to off(2).

atmVpCrossConnectExtenTable

1.3.6.1.4.1.164.12.3.1.1.34

not-accessible

An extension to the ATM VP Cross Connect table (RFC2515 - atmVpCrossConnectTable).

atmVpCrossConnectExtenEntry

1.3.6.1.4.1.164.12.3.1.1.34.1

not-accessible

An entry in the table.

STR atmVpCrossConnectName

1.3.6.1.4.1.164.12.3.1.1.34.1.1

SnmpAdminString

read-create

The Connection's name.

atmVcCrossConnectExtenTable

1.3.6.1.4.1.164.12.3.1.1.35

not-accessible

An extension to the ATM VC Cross Connect table (RFC2515 - atmVcCrossConnectTable).

atmVcCrossConnectExtenEntry

1.3.6.1.4.1.164.12.3.1.1.35.1

not-accessible

An entry in the table.

STR atmVcCrossConnectName

1.3.6.1.4.1.164.12.3.1.1.35.1.1

SnmpAdminString

read-create

The Connection's name.

INT atmNteQosMode

1.3.6.1.4.1.164.12.3.1.1.37

INTEGER

read-write

This variable defines the QoS Mode. disable(1) - QoS is disabled. multipleVc(2) - QoS is enabled and multiple VCs can be bound per bridge port. singleVc(3) - QoS is enabled and only single VC can be bound per bridge port.

atmTrafficDescrParamXTable

1.3.6.1.4.1.164.12.3.1.1.38

not-accessible

An Augment to ATM Traffic Descriptor Parameter Table (atmTrafficDescrParamTable in ATM-MIB; RFC-2515).

atmTrafficDescrParamXEntry

1.3.6.1.4.1.164.12.3.1.1.38.1

not-accessible

An entry in the table.

INT atmTrafficDescrParamMode

1.3.6.1.4.1.164.12.3.1.1.38.1.1

INTEGER

read-create

The Mode of the Traffic Descriptor.

atmNteSysInfo

1.3.6.1.4.1.164.12.3.1.2

atmNteIdTable

1.3.6.1.4.1.164.12.3.1.2.1

not-accessible

The IDs of the cards and of the system.

atmNteIdEntry

1.3.6.1.4.1.164.12.3.1.2.1.1

not-accessible

.

I32 atmNteIdIndex

1.3.6.1.4.1.164.12.3.1.2.1.1.1

Integer32

read-only

An Index of the Unit ID table. The following units have IDs in this table: 1 - System 2 - ATM Board 3 - User Card 4 - Trunk 1 card 5 - Trunk 2 card 6 - Shaper 7 - Clock Unit 8 - Slot 1 card 9 - Slot 2 card 10 - Slot 3 card 11 - Slot 4 card 12 - Fan1 13 - Fan2 14 - Control Unit.

I32 atmNteUnitId

1.3.6.1.4.1.164.12.3.1.2.1.1.2

Integer32

read-only

The ID of the Unit. For index = 6, the id will describe the validity of a shaper in the system: 0 - Shaper Not exist 1 - Shaper exist. For index = 7, the id will describe the validity of a clock in the system: 0 - Clock Not exist 1 - Clock exist. 2- Clock exist but failed. For index = 12,13 the id will describe the functionality of a FAN1 : 0 - OK 1 - Failed.

STR atmNteUnitVersion

1.3.6.1.4.1.164.12.3.1.2.1.1.3

DisplayString

read-only

Hardware and Software version of the module.

INT atmNteCardType

1.3.6.1.4.1.164.12.3.1.2.1.1.4

INTEGER

read-only

The card type.

INT atmNteCardStatus

1.3.6.1.4.1.164.12.3.1.2.1.1.5

INTEGER

read-only

Status of the card in the selected slot. notActive - Connections are in NotReady state. No configuration is available for the card. The access to the card HW is blocked. This state is relevant for an extracted card, and for a case in which the card was deactivated. active - The module installed and functions. A card that in this state can be configured. inProgress - The status during proccessing of a command from atmNteCardCmd. empty - No information is valid for the selected slot. This status is relevant to a case in which the card configaration was deleted, or in case in which a slot was empty since the device startup.

INT atmNteCardCmd

1.3.6.1.4.1.164.12.3.1.2.1.1.6

INTEGER

read-write

Command on the card that is installed in the selected slot. The commands are applicable according to the value of atmNteCardStatus. See the specification document for details. deleteConfig - Deletes the card configuration. deactivate - All the connections state will be changed to NotReady. The card configuration will be blocked. activate - Does the same as done upon card insertion: Initiates the relevant parameters, activates the physical layer, ATM layer and logical layer.

INT atmNteProgCardType

1.3.6.1.4.1.164.12.3.1.2.1.1.7

INTEGER

read-write

The programmed card type.

I32 atmSysPSunits

1.3.6.1.4.1.164.12.3.1.2.2

Integer32

read-only

The number of power supply units.

INT atmSysPSunitsInUse

1.3.6.1.4.1.164.12.3.1.2.3

INTEGER

read-only

The main power supply in this unit.

I32 atmSysFanUnits

1.3.6.1.4.1.164.12.3.1.2.4

Integer32

read-only

The number of fan units.

I32 atmSysNetPrts

1.3.6.1.4.1.164.12.3.1.2.5

Integer32

read-only

The number of network ports.

INT atmSysNetPrtInUse

1.3.6.1.4.1.164.12.3.1.2.6

INTEGER

read-only

The network port in use.

INT atmNteBridgingMode

1.3.6.1.4.1.164.12.3.1.2.7

INTEGER

read-write

Bridging mode can be one of the following: ATM <> Ethernet - Bridging is between the Ethernet port and the ATM port (there is no bridging between VCs). ATM <> Ethernet + ATM - Bridging is done both between the Ethernet port and the ATM port and also between VCs.

atmSysStats

1.3.6.1.4.1.164.12.3.1.2.8

G32 atmSysCurrentCdc

1.3.6.1.4.1.164.12.3.1.2.8.1

Gauge32

read-only

Seconds in which cells dropped was occured in the current 15 minutes interval.

atmSysIntervalTable

1.3.6.1.4.1.164.12.3.1.2.8.2

not-accessible

The system level Interval table.

atmSysIntervalEntry

1.3.6.1.4.1.164.12.3.1.2.8.2.1

not-accessible

.

I32 atmSysIntervalNumber

1.3.6.1.4.1.164.12.3.1.2.8.2.1.1

Integer32

read-only

A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).

G32 atmSysIntervalCdc

1.3.6.1.4.1.164.12.3.1.2.8.2.1.2

Gauge32

read-only

Seconds in which cells dropped was occured in 15 minutes interval.

INT atmNteEventType

1.3.6.1.4.1.164.12.3.1.2.9

INTEGER

read-only

This parameter identifies the event. On - the problem exist. Off - the problem not exist. InvalidLogin - Invalid login on local console. CorrectLogin - Successful login operation.

I32 atmNteIntervalMaxNumber

1.3.6.1.4.1.164.12.3.1.2.10

Integer32

read-only

The MAX number of connections intervals supported by system. This parameter value is a function of atmNteConnectionsMaxNumber parameter. This parameter should affect the threshold values selected by user. Applicable to ace2002.

INT atmNteAlarmType

1.3.6.1.4.1.164.12.3.1.2.11

INTEGER

read-only

This object specifies the type of the alarm.

INT atmNteLevel

1.3.6.1.4.1.164.12.3.1.2.12

INTEGER

read-only

This object specifies the ATM level.

I32 atmNteConnectionsNumber

1.3.6.1.4.1.164.12.3.1.2.13

Integer32

read-only

This object specifies a quantity of connections.

I32 atmNteTotalLb

1.3.6.1.4.1.164.12.3.1.2.14

Integer32

read-only

This parameter counts the total number of end-points that were configured with Loopback (LB).

I32 atmNteTotalCc

1.3.6.1.4.1.164.12.3.1.2.15

Integer32

read-only

This parameter counts the total number of end-points that were configured with Continuity Check (CC).

I32 atmNteTotalPm

1.3.6.1.4.1.164.12.3.1.2.16

Integer32

read-only

This parameter counts the total number of end-points that were configured with PM.

atmNtePrt

1.3.6.1.4.1.164.12.3.2

atmNtePrtConfig

1.3.6.1.4.1.164.12.3.2.1

atmNteConfIfTable

1.3.6.1.4.1.164.12.3.2.1.1

not-accessible

The Physical interface configuration table.

atmNteConfIfEntry

1.3.6.1.4.1.164.12.3.2.1.1.1

not-accessible

An entry in the Physical interface configuration table. The ifIndex is of the lowest physical layer.

INT atmConfIfTransmitClk

1.3.6.1.4.1.164.12.3.2.1.1.1.1

INTEGER

read-write

The transmit clock of the port.

INT atmConfIfLoopback

1.3.6.1.4.1.164.12.3.2.1.1.1.2

INTEGER

read-write

Interface Loopback.

INT atmConfIfFrameType

1.3.6.1.4.1.164.12.3.2.1.1.1.3

INTEGER

read-write

The frame type. Valid values for a 155M interface: sonet(2), sdh(3). Valid values for a T3 interface: direct(4), plcpInternal(5), plcpExternal(6), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbling(12). Valid values for Ethernet interface: ethCrcTrans (8), ethCrcNotTrans(9). (DS1 interfaces frame type is specified in the DSX1 mib).

INT atmConfIfCardType

1.3.6.1.4.1.164.12.3.2.1.1.1.4

INTEGER

read-only

The card type.

INT atmConfAtmIfVpiVciLimit

1.3.6.1.4.1.164.12.3.2.1.1.1.5

INTEGER

read-only

The limit on the sum of the VPI+VCI bits for this interface.

INT atmConfIfHwFeatures

1.3.6.1.4.1.164.12.3.2.1.1.1.6

INTEGER

read-write

HW features command.

I32 atmConfIfOutputRate

1.3.6.1.4.1.164.12.3.2.1.1.1.7

Integer32

read-write

This parameter indicates the output rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.

I32 atmConfIfInputRate

1.3.6.1.4.1.164.12.3.2.1.1.1.8

Integer32

read-write

This parameter indicates the input rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.

INT atmConfAlarmForwarding

1.3.6.1.4.1.164.12.3.2.1.1.1.9

INTEGER

read-write

Enables Path AIS Alarm forwarding upon a failure detection. The following might be considered as a failure: LOS, LOF, LOC, SLM, LOP, Path AIS and Line AIS. disable(2) - will not forward an alarm upon a failure on this port. enable(3) - will forward an alarm upon a failure on this port.

I32 atmConfIfAllocatedBw

1.3.6.1.4.1.164.12.3.2.1.1.1.10

Integer32

read-only

Total VC Bandwidth Allocation.

I32 atmConfIfLowerVpi

1.3.6.1.4.1.164.12.3.2.1.1.1.11

Integer32

read-write

The Lower possible VPI.

INT atmConfIfOamMode

1.3.6.1.4.1.164.12.3.2.1.1.1.12

INTEGER

read-write

OAM support Mode, which determines the interface's location in a segment wise.

INT atmConfIfOamFailureInd

1.3.6.1.4.1.164.12.3.2.1.1.1.13

INTEGER

read-write

This object allows user to define the type of indication (if any) that will be created upon a LB cell failure, for all VCs on which OAM loopback traffic is activated. disabled(2) - no indication will be created. ais(3) - will cause Tx of AIS. rdi(4) - will cause Tx of RDI. aisAndRdi(5) - will cause Tx of AIS & RDI. For LA-110, indication will be sent only for VCs with atmConfVcLoopbackFailureInd <> disabled

atmNteAlarmIfTable

1.3.6.1.4.1.164.12.3.2.1.2

not-accessible

The interface Alarm table.

atmNteAlarmIfEntry

1.3.6.1.4.1.164.12.3.2.1.2.1

not-accessible

An entry in the interface Alarm table.

I32 atmInterfaceActiveAlarms

1.3.6.1.4.1.164.12.3.2.1.2.1.1

Integer32

read-only

A Bit String of the active alarms on this interface. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - LOS 2 - LOF 3 - Line AIS (SONET)/ PLCP LOF (DS3) 4 - LOP 5 - Path AIS 6 - SLM 7 - LCD 8 - Line RDI (SONET)/ PLCP Yellow (DS3) 9 - Path RDI (SONET)/ RDI (DS3) 10 - Section BIP (SONET)/ P1/P2 (DS3) > Threshold 11 - Line BIP (SONET)/ PLCP BIP (DS3) > Threshold 12 - Line FEBE (SONET)/ PLCP FEBE (DS3) > Threshold 13 - Path BIP > Threshold 14 - Path FEBE > Threshold 15 - HW Failure

I32 atmThresholdSectionBIP

1.3.6.1.4.1.164.12.3.2.1.2.1.2

Integer32

read-write

When Section BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.

I32 atmThresholdLineBIP

1.3.6.1.4.1.164.12.3.2.1.2.1.3

Integer32

read-write

When Line BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.

I32 atmThresholdLineFEBE

1.3.6.1.4.1.164.12.3.2.1.2.1.4

Integer32

read-write

When Line FEBEs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.

I32 atmThresholdPathBIP

1.3.6.1.4.1.164.12.3.2.1.2.1.5

Integer32

read-write

When Path BIPs are greater than this threshold, an active alarm is raised.

I32 atmThresholdPathFEBE

1.3.6.1.4.1.164.12.3.2.1.2.1.6

Integer32

read-write

When Path FEBEs are greater than this threshold, an active alarm is raised.

I32 atmThresholdErroredCells

1.3.6.1.4.1.164.12.3.2.1.2.1.7

Integer32

read-write

When Errored Cells are greater than this threshold, an active alarm is raised.

I32 atmThresholdLostCells

1.3.6.1.4.1.164.12.3.2.1.2.1.8

Integer32

read-write

When Lost Cells are greater than this threshold, an active alarm is raised.

I32 atmThresholdMisinsertedCells

1.3.6.1.4.1.164.12.3.2.1.2.1.9

Integer32

read-write

When Misinserted Cells are greater than this threshold, an active alarm is raised.

INT atmInterfaceAlarmStatus

1.3.6.1.4.1.164.12.3.2.1.2.1.10

INTEGER

read-only

The variable is on(3) when there is any active alarm on this interface.

I32 atmInterfaceMaskAlarms

1.3.6.1.4.1.164.12.3.2.1.2.1.11

Integer32

read-write

A Bit String of alarms mask on this interface. An up bit (1) means that the respective alarm is masked. A down bit (0) means no mask. The mask is supported for the following alarms: 1 - LOS

atmNteConfVpTable

1.3.6.1.4.1.164.12.3.2.1.3

not-accessible

The ATM VP configuration table. The table is an extension to the atmVplTable of RFC-1695.

atmNteConfVpEntry

1.3.6.1.4.1.164.12.3.2.1.3.1

not-accessible

An entry in the ATM VP configuration table. ifIndex of the ATM layer.

INT atmConfVpPolicing

1.3.6.1.4.1.164.12.3.2.1.3.1.1

INTEGER

read-write

Policing method desired for this VPL.

INT atmConfVpCCAdminStatus

1.3.6.1.4.1.164.12.3.2.1.3.1.2

INTEGER

read-write

up(2) - Activate Continuity Check (CC). down(3) - Deactivate CC. source(4) - Activate OAM CC(Continuity Check) of local agent ( start sending Oam cells to the remote side ). sink(5) - Activate CC of remote agent ( start receiving Oam cells from remote side ). listenToActivationCells (6) - Passive listener till gets an activation request originateActivationCells(7) - Sands Activation cell according to atmConfVcCCDirection.

INT atmConfVpLoopbackAdminStatus

1.3.6.1.4.1.164.12.3.2.1.3.1.3

INTEGER

read-write

up(2) - Start loopback OAM cells. down(3) - Stop sending loopback OAM cells. For ace2002: up(2) - Transmitting LB cells with llid all ones (i.e. FFFF..FF) down(3) - Not transmitting LB cells. llid(4) - Transmitting LB cells with llid indicated in the address field. segment(5) - Transmitting Segment LB cells with llid all ones. endToEnd(6) - Transmitting End to End LB cells with llid all ones. segmentLlid(7) - Transmitting Segment LB cells with llid indicated in the address field. endToEndLlid(8) - Transmitting LB cells with llid indicated in the address field. This parameter value might be in conflict with atmConfVpOamSupport value, since this parameter is for LB, while atmConfVpOamSupport is for any other OAM cells.

OCT atmConfVpLoopbackSinkAddress

1.3.6.1.4.1.164.12.3.2.1.3.1.4

OCTET STRING

read-write

Destination address. For ace101: 2 bytes are used. For ace2002: 16 bytes are used.

OCT atmConfVpCongestionControl

1.3.6.1.4.1.164.12.3.2.1.3.1.5

OCTET STRING

read-write

Each bit indicates a selection of one option as the following description. All combinations are possible and legal. The codes are: 1 - EPD 2 - CLP 4 - EFCI

INT atmConfVpCCDirection

1.3.6.1.4.1.164.12.3.2.1.3.1.6

INTEGER

read-write

both(2) - Agent send OAM CC cells and check received OAM CC cells source(4)- Agent send OAM CC cells. sink(5) - Agent checks received OAM CC cells.

DAT atmConfVpCreationTime

1.3.6.1.4.1.164.12.3.2.1.3.1.7

DateAndTime

read-only

A date-time in which the VP was created.

INT atmConfVpOamSupport

1.3.6.1.4.1.164.12.3.2.1.3.1.8

INTEGER

read-write

OAM support mode, which determines the device location in a segment wise.

INT atmConfVpCCOperStatus

1.3.6.1.4.1.164.12.3.2.1.3.1.9

INTEGER

read-only

initial(1) - The CC activation process is not started. source(4) - Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells. both (8) - OAM CC of local and remote agents activation. timeout (9) - Timeout occured on receiving answer from the remote agent. denied (10) - CC activation process rejected by remote agent. conflict (11) - local and remote sides requested activation simultaneously. manual (12) - OAM CC of local agent activated manually.

INT atmConfVpLoopbackTraffic

1.3.6.1.4.1.164.12.3.2.1.3.1.10

INTEGER

read-write

This parameter has both command and status meanings: off(2) - Set to 'Off' will Stop traffic loop. Getting this value means that the loop is not running. on (3) - Set to 'On' will start traffic loop. Getting this value means that the loop is currently running.

INT atmConfVpLoopbackFailureInd

1.3.6.1.4.1.164.12.3.2.1.3.1.11

INTEGER

read-write

This object allows user to define the Indication that will be created upon a LB cell failure. disabled(2) - no indication will be created. segmentAis(3) - will cause Tx of a segment AIS. segmentRdi(4) - will cause Tx of a segment RDI. segmentAisAndRdi(5) - will cause Tx of a segment AIS & RDI. endToEndAis(6) - will cause Tx of an End to End AIS. endToEndRdi(7) - will cause Tx of an End to End RDI. endToEndAisAndRdi(8) - will cause Tx of an End to End AIS & RDI. Default: disabled(2).

I32 atmConfVpLoopbackFailureThreshold

1.3.6.1.4.1.164.12.3.2.1.3.1.12

Integer32

read-write

The number of the LB failures before starting transmission of the Indication defined by atmConfVcLoopbackFailureInd. Range: 1..16. Default: 1.

INT atmConfVpOamDirection

1.3.6.1.4.1.164.12.3.2.1.3.1.13

INTEGER

read-write

The direction of OAM cell insertion. downStream(2) - The OAM cell will be inserted in downStream. upStream(3) - The OAM cell will be inserted in upStream.

I32 atmConfVpOamDescrIndex

1.3.6.1.4.1.164.12.3.2.1.3.1.14

Integer32

read-write

This parameter indicates the VPL's OAM Descriptor index, according to the OAM Descriptor Configuration Table.

INT atmConfVpConnected

1.3.6.1.4.1.164.12.3.2.1.3.1.15

INTEGER

read-write

This object indicates whether this VP is connected and if connected, what is it connected to.

atmNteAlarmVpTable

1.3.6.1.4.1.164.12.3.2.1.5

not-accessible

The ATM VP Alarm table.

atmNteAlarmVpEntry

1.3.6.1.4.1.164.12.3.2.1.5.1

not-accessible

An entry in the ATM VP Alarm table. ifIndex of the ATM layer.

I32 atmNteVpAlarmVpi

1.3.6.1.4.1.164.12.3.2.1.5.1.1

Integer32

read-only

The VPI on which there is an active alarm.

I32 atmNteVpActiveAlarms

1.3.6.1.4.1.164.12.3.2.1.5.1.2

Integer32

read-only

A Bit String of the active alarms on this VP. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VP AIS 2 - VP Loss Of Continuity 3 - VP RDI Reception 4 - VP Errored Cells > Threshold 5 - VP Lost Cells > Threshold 6 - VP Misinserted Cells > Threshold 9 - VP Loopback Failure

atmNteAlarmVcTable

1.3.6.1.4.1.164.12.3.2.1.6

not-accessible

The ATM VC Alarm table.

atmNteAlarmVcEntry

1.3.6.1.4.1.164.12.3.2.1.6.1

not-accessible

An entry in the ATM VC Alarm table. ifIndex of the ATM layer.

I32 atmNteVcAlarmVpi

1.3.6.1.4.1.164.12.3.2.1.6.1.1

Integer32

read-only

The VPI of the VC on which there is an active alarm.

I32 atmNteVcAlarmVci

1.3.6.1.4.1.164.12.3.2.1.6.1.2

Integer32

read-only

The VCI of the VC on which there is an active alarm.

I32 atmNteVcActiveAlarms

1.3.6.1.4.1.164.12.3.2.1.6.1.3

Integer32

read-only

A Bit String of the active alarms on this VC. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VC AIS 2 - VC Loss Of Continuity 3 - VC RDI 4 - VC Errored Cells > Threshold 5 - VC Lost Cells > Threshold 6 - VC Misinserted Cells > Threshold 7 - Tx VC AIS 8 - Tx VC RDI 9 - VC Loopback Failure

atmNteLoopback

1.3.6.1.4.1.164.12.3.2.2

atmLoopbackVpTable

1.3.6.1.4.1.164.12.3.2.2.1

not-accessible

This table contains parameters for an OAM VP loopback test.

atmLoopbackVpEntry

1.3.6.1.4.1.164.12.3.2.2.1.1

not-accessible

An entry in table atmLoopbackVpTable.

I32 atmLoopbackVpIfIndex

1.3.6.1.4.1.164.12.3.2.2.1.1.1

Integer32

read-only

The interface index of the ATM layer.

I32 atmLoopbackVpVpi

1.3.6.1.4.1.164.12.3.2.2.1.1.2

Integer32

read-only

The VPI of the OAM VPL.

INT atmLoopbackVpOperStatus

1.3.6.1.4.1.164.12.3.2.2.1.1.3

INTEGER

read-only

-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.

I32 atmLoopbackVpCDV

1.3.6.1.4.1.164.12.3.2.2.1.1.4

Integer32

read-only

Cell Delay Variation for this sampling.

I32 atmLoopbackVpAverageDelay

1.3.6.1.4.1.164.12.3.2.2.1.1.5

Integer32

read-only

Average delay without including lost cells.

I32 atmLoopbackVpMaxDelay

1.3.6.1.4.1.164.12.3.2.2.1.1.6

Integer32

read-only

Maximum delay without including lost cells.

I32 atmLoopbackVpMinDelay

1.3.6.1.4.1.164.12.3.2.2.1.1.7

Integer32

read-only

Minimum delay.

I32 atmLoopbackVpErrSessions

1.3.6.1.4.1.164.12.3.2.2.1.1.8

Integer32

read-only

Errored Sessions. Will be updated once in 5 seconds.

atmLoopbackVcTable

1.3.6.1.4.1.164.12.3.2.2.2

not-accessible

This table contains parameters for an OAM VC loopback test.

atmLoopbackVcEntry

1.3.6.1.4.1.164.12.3.2.2.2.1

not-accessible

An entry in table.

I32 atmLoopbackVcIfIndex

1.3.6.1.4.1.164.12.3.2.2.2.1.1

Integer32

read-only

The interface index of the ATM layer.

I32 atmLoopbackVcVpi

1.3.6.1.4.1.164.12.3.2.2.2.1.2

Integer32

read-only

The VPI of the OAM VCL.

I32 atmLoopbackVcVci

1.3.6.1.4.1.164.12.3.2.2.2.1.3

Integer32

read-only

The VCI of the OAM VCL.

INT atmLoopbackVcOperStatus

1.3.6.1.4.1.164.12.3.2.2.2.1.4

INTEGER

read-only

-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.

I32 atmLoopbackVcCDV

1.3.6.1.4.1.164.12.3.2.2.2.1.5

Integer32

read-only

Cell Delay Variation for this sampling.

I32 atmLoopbackVcAverageDelay

1.3.6.1.4.1.164.12.3.2.2.2.1.6

Integer32

read-only

Average delay without including lost cells.

I32 atmLoopbackVcMaxDelay

1.3.6.1.4.1.164.12.3.2.2.2.1.7

Integer32

read-only

The maximum delay without including lost cells.

I32 atmLoopbackVcMinDelay

1.3.6.1.4.1.164.12.3.2.2.2.1.8

Integer32

read-only

The minimum delay.

I32 atmLoopbackVcErrSessions

1.3.6.1.4.1.164.12.3.2.2.2.1.9

Integer32

read-only

Errored Sessions. Will be updated once in 5 seconds.

atmLoopbackVpIvlTable

1.3.6.1.4.1.164.12.3.2.2.3

not-accessible

This table contains parameters for an OAM VP loopback test, according interval number.

atmLoopbackVpIvlEntry

1.3.6.1.4.1.164.12.3.2.2.3.1

not-accessible

An entry in table.

I32 atmLoopbackVpIvlIfIndex

1.3.6.1.4.1.164.12.3.2.2.3.1.1

Integer32

read-only

The interface index of the ATM layer.

I32 atmLoopbackVpIvlVpi

1.3.6.1.4.1.164.12.3.2.2.3.1.2

Integer32

read-only

The VPI of the OAM VPL.

I32 atmLoopbackVpIvlIvl

1.3.6.1.4.1.164.12.3.2.2.3.1.3

Integer32

read-only

The relevant interval number.

INT atmLoopbackVpIvlOperStatus

1.3.6.1.4.1.164.12.3.2.2.3.1.4

INTEGER

read-only

-noActive(1) means that the loopback test has not been activated for this VP during this interval. -inProgress(2) has no meaning for an ended interval. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was OK.

I32 atmLoopbackVpIvlCDV

1.3.6.1.4.1.164.12.3.2.2.3.1.5

Integer32

read-only

Cell Delay Variation for this interval.

I32 atmLoopbackVpIvlAverageDelay

1.3.6.1.4.1.164.12.3.2.2.3.1.6

Integer32

read-only

Average delay without including lost cells for this interval.

I32 atmLoopbackVpIvlMaxDelay

1.3.6.1.4.1.164.12.3.2.2.3.1.7

Integer32

read-only

The maximum delay without including lost cells for this interval.

I32 atmLoopbackVpIvlMinDelay

1.3.6.1.4.1.164.12.3.2.2.3.1.8

Integer32

read-only

The minimum delay for this interval.

I32 atmLoopbackVpIvlErrSessions

1.3.6.1.4.1.164.12.3.2.2.3.1.9

Integer32

read-only

Errored Sessions. Will be updated once in 5 seconds.

atmLoopbackVcIvlTable

1.3.6.1.4.1.164.12.3.2.2.4

not-accessible

This table contains parameters for an OAM VC loopback test.

atmLoopbackVcIvlEntry

1.3.6.1.4.1.164.12.3.2.2.4.1

not-accessible

An entry in table.

I32 atmLoopbackVcIvlIfIndex

1.3.6.1.4.1.164.12.3.2.2.4.1.1

Integer32

read-only

The interface index of the ATM layer.

I32 atmLoopbackVcIvlVpi

1.3.6.1.4.1.164.12.3.2.2.4.1.2

Integer32

read-only

The VPI of the OAM VCL.

I32 atmLoopbackVcIvlVci

1.3.6.1.4.1.164.12.3.2.2.4.1.3

Integer32

read-only

The VCI of the OAM VCL.

I32 atmLoopbackVcIvlIvl

1.3.6.1.4.1.164.12.3.2.2.4.1.4

Integer32

read-only

The relevant interval number.

INT atmLoopbackVcIvlOperStatus

1.3.6.1.4.1.164.12.3.2.2.4.1.5

INTEGER

read-only

-noActive(1) means that the loopback test has not been activated for this VC during this interval. -inProgress(2) has no meaning per interval. -failed(3) means there was problem for this test during this interval. -endSuccessfully(4) means that the test was OK.

I32 atmLoopbackVcIvlCDV

1.3.6.1.4.1.164.12.3.2.2.4.1.6

Integer32

read-only

Cell Delay Variation for this interval.

I32 atmLoopbackVcIvlAverageDelay

1.3.6.1.4.1.164.12.3.2.2.4.1.7

Integer32

read-only

Average delay without including lost cells.

I32 atmLoopbackVcIvlMaxDelay

1.3.6.1.4.1.164.12.3.2.2.4.1.8

Integer32

read-only

The maximum delay without including lost cells.

I32 atmLoopbackVcIvlMinDelay

1.3.6.1.4.1.164.12.3.2.2.4.1.9

Integer32

read-only

The minimum delay.

I32 atmLoopbackVcIvlErrSessions

1.3.6.1.4.1.164.12.3.2.2.4.1.10

Integer32

read-only

Errored Sessions. Will be updated once in 5 seconds.

atmNtePM

1.3.6.1.4.1.164.12.3.2.3

atmVpPmTable

1.3.6.1.4.1.164.12.3.2.3.1

not-accessible

This table contains parameters for VP performance monitoring.

atmVpPmEntry

1.3.6.1.4.1.164.12.3.2.3.1.1

not-accessible

An entry in table.

I32 atmVpPmIfIndex

1.3.6.1.4.1.164.12.3.2.3.1.1.1

Integer32

read-only

The interface index of the ATM layer.

I32 atmVpPmVpi

1.3.6.1.4.1.164.12.3.2.3.1.1.2

Integer32

read-only

The VPI of the Performance Monitoring VPL.

INT atmVpPmAdminStatus

1.3.6.1.4.1.164.12.3.2.3.1.1.3

INTEGER

read-create

up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .

INT atmVpPmDirection

1.3.6.1.4.1.164.12.3.2.3.1.1.4

INTEGER

read-create

The direction of PM.

I32 atmVpPmBlockSize

1.3.6.1.4.1.164.12.3.2.3.1.1.5

Integer32

read-create

Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.

ROW atmVpPmRowStatus

1.3.6.1.4.1.164.12.3.2.3.1.1.6

RowStatus

read-create

Creation/Deletion of rows in the table.

INT atmVpPmSink

1.3.6.1.4.1.164.12.3.2.3.1.1.7

INTEGER

read-create

off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.

INT atmVpPmSource

1.3.6.1.4.1.164.12.3.2.3.1.1.8

INTEGER

read-create

off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.

atmVcPmTable

1.3.6.1.4.1.164.12.3.2.3.2

not-accessible

This table contains parameters for VC performance monitoring.

atmVcPmEntry

1.3.6.1.4.1.164.12.3.2.3.2.1

not-accessible

An entry in table.

I32 atmVcPmIfIndex

1.3.6.1.4.1.164.12.3.2.3.2.1.1

Integer32

read-only

The interface index of the ATM layer.

I32 atmVcPmVpi

1.3.6.1.4.1.164.12.3.2.3.2.1.2

Integer32

read-only

The VPI of the Performance Monitoring VCL.

I32 atmVcPmVci

1.3.6.1.4.1.164.12.3.2.3.2.1.3

Integer32

read-only

The VCI of the PM VCL.

INT atmVcPmAdminStatus

1.3.6.1.4.1.164.12.3.2.3.2.1.4

INTEGER

read-create

up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .

INT atmVcPmDirection

1.3.6.1.4.1.164.12.3.2.3.2.1.5

INTEGER

read-create

The direction of PM.

I32 atmVcPmBlockSize

1.3.6.1.4.1.164.12.3.2.3.2.1.6

Integer32

read-create

Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.

ROW atmVcPmRowStatus

1.3.6.1.4.1.164.12.3.2.3.2.1.7

RowStatus

read-create

Creation/Deletion of rows in the table.

INT atmVcPmSink

1.3.6.1.4.1.164.12.3.2.3.2.1.8

INTEGER

read-create

off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.

INT atmVcPmSource

1.3.6.1.4.1.164.12.3.2.3.2.1.9

INTEGER

read-create

off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.

atmNteMdl

1.3.6.1.4.1.164.12.3.3

atmNteMdlConfig

1.3.6.1.4.1.164.12.3.3.1

atmNteMdlConfigTable

1.3.6.1.4.1.164.12.3.3.1.1

not-accessible

Module configuration table.

atmNteMdlConfigEntry

1.3.6.1.4.1.164.12.3.3.1.1.1

not-accessible

There is an entry in this table just for those modules that have parameters that are relevant to module level only.

I32 atmNteMdlSlotIndex

1.3.6.1.4.1.164.12.3.3.1.1.1.1

Integer32

not-accessible

The slot number.

INT atmNteMdlPrtCpuSharing

1.3.6.1.4.1.164.12.3.3.1.1.1.2

INTEGER

read-write

This object lets the user decide what will be the CPU sharing between the ports of the module. This object is applicable for modules in which the same CPU handles the traffic of all ports. equal - All ports will have the same CPU resource. port1 - Port 1 will have higher priority than the other ports.

INT atmNteMdlInputPriorityMechanism

1.3.6.1.4.1.164.12.3.3.1.1.1.3

INTEGER

read-write

This object allows the user to Enable/Disable the Input priority mechanism. This object is applicable for modules with more than one port, in which the total ports input may be greater than the port output. disabled - all LAN VCCs will be transmitted through the same queue (queue 1). Upon congestion frames will be dropped randomly. enabled - the user should configure each port/connection priority. Upon congestion frames will be dropped according to priority.