CIENA-CES-MPLS-MIB

All MIBs › CIENA-CES-MPLS-MIB

Organization: Ciena, Inc

Last Updated: 2016-11-22

Category: MPLS and Traffic Engineering, Vendor: Ciena

Description: Manages MPLS label switched paths and forwarding tables on Ciena CES Carrier Ethernet switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CIENA-CES-MPLS-MIB?

CIENA-CES-MPLS-MIB is a Ciena vendor MIB managing MPLS and GMPLS label switched path (LSP) data on Carrier Ethernet Switching (CES) platforms, extending the standard MPLS traffic-engineering model with explicit-route hop tracking. It exposes actual-route hop tables for both MPLS and GMPLS tunnels, recording each hop's index, address type, IP address, unnumbered interface identifier, and LSP ID along the established path. Its monitoring value is chiefly software/protocol-path oriented, allowing an operator to verify the actual path an LSP took through the network versus its intended path, which is essential for troubleshooting suboptimal routing, verifying traffic-engineering constraints, and diagnosing LSP setup failures on a carrier Ethernet/MPLS network. It builds directly on the standard MPLS-TE and GMPLS-TE MIBs, extending their tunnel model with Ciena-specific actual-hop reporting. It's deployed in service-provider MPLS/GMPLS backbone or metro networks running Ciena CES switches where LSP path verification is a routine operational task. Network engineers evaluating or troubleshooting this functionality can download the CIENA-CES-MPLS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CIENA-CES-MPLS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ciena CES Carrier Ethernet switch

Monitoring Examples

An engineer polls cienaMplsTunnelARHopListIndex and cienaMplsTunnelARHopIndex to enumerate the actual hop-by-hop path taken by a specific LSP, cross-referencing cienaMplsTunnelARHopIpAddr and cienaMplsTunnelARHopLspId against the intended explicit route. For GMPLS tunnels, the parallel cienaGmplsTunnelARHopIpAddr and cienaGmplsTunnelARHopLspId tables are used the same way to verify optical/TDM path setup. A mismatch between the actual hop list and the configured explicit route would indicate the LSP was signaled via an alternate path, possibly due to a link failure or constraint-based rerouting event upstream.

What Can Be Monitored

MPLS LSP actual hop path
GMPLS LSP actual hop path
hop IP address / unnumbered interface ID
LSP identifier per hop

Imported Objects

From CIENA-GLOBAL-MIB

cienaGlobalMacAddress	OBJECT-TYPE
cienaGlobalSeverity	OBJECT-TYPE

From CIENA-SMI

cienaCesConfig	OBJECT-IDENTITY
cienaCesNotifications	OBJECT-IDENTITY

From CIENA-TC

CienaGlobalState

From IANA-ADDRESS-FAMILY-NUMBERS-MIB

AddressFamilyNumbers

From MPLS-TC-STD-MIB

MplsBitRate

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowPointer
RowStatus
StorageType
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using cienaCesMplsTunnelPathUseCount OID:

Select a Ciena Carrier Ethernet switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cienaCesMplsTunnelPathUseCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Indicates the number of encap tunnels that are using this path. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
cienaCesMplsMIB	1.3.6.1.4.1.1271.2.1.18			This MIB module defines the mgmt objects for the MPLS feature for LEOS based Ciena products.
cienaCesMplsMIBObjects	1.3.6.1.4.1.1271.2.1.18.1
cienaCesMpls	1.3.6.1.4.1.1271.2.1.18.1.1
cienaCesMplsGlobalAttrs	1.3.6.1.4.1.1271.2.1.18.1.1.1
INT cienaCesMplsStaticAdminLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.1.1.1	INTEGER	read-only	The beginning of the static administrative label range. There cannot be any overlap between static and dynamic label ranges. Setting this object does not become effective until the device is rebooted.
INT cienaCesMplsStaticAdminLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.1.1.2	INTEGER	read-only	The end of the static administrative label range. There cannot be any overlap between static and dynamic label ranges. Setting this object does not become effective until the device is rebooted.
INT cienaCesMplsStaticOperLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.1.1.3	INTEGER	read-only	The beginning of the static operational label range. There cannot be any overlap between static and dynamic label ranges.
INT cienaCesMplsStaticOperLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.1.1.4	INTEGER	read-only	The end of the static operational label range. There cannot be any overlap between static and dynamic label ranges.
INT cienaCesMplsDynamicAdminLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.1.1.5	INTEGER	read-only	The beginning of the dynamic administrative label range. There cannot be any overlap between static and dynamic label ranges.
INT cienaCesMplsDynamicAdminLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.1.1.6	INTEGER	read-only	The end of the dynamic administrative label range. There cannot be any overlap between static and dynamic label ranges.
INT cienaCesMplsDynamicOperLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.1.1.7	INTEGER	read-only	The beginning of the dynamic operational label range. There cannot be any overlap between static and dynamic label ranges.
INT cienaCesMplsDynamicOperLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.1.1.8	INTEGER	read-only	The end of the dynamic operational label range. There cannot be any overlap between static and dynamic label ranges.
cienaCesMplsStaticIngressTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.2		not-accessible	The (conceptual) table listing the MPLS static encap tunnels.
cienaCesMplsStaticIngressTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.2.1		not-accessible	This represents an entry of the MPLS static encap tunnel table.
U32 cienaCesMplsStaticIngressTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.1	Unsigned32	not-accessible	Unique index in the table.
STR cienaCesMplsStaticIngressTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.2	DisplayString	read-only	This represents the encap tunnel name. Tunnel names are common across static and dynamic.
INT cienaCesMplsStaticIngressTunnelWeight	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.3	INTEGER	read-only	A parameter to select the order of precedence of encap tunnels during tunnel switchover or reversion (if tunnel reversion is enabled). A higher weight indicates higher preference during switchover or reversion.
IP cienaCesMplsStaticIngressTunnelNextHopIp	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.4	IpAddress	read-only	Specifies the next hop IP address for the static encap tunnel.
CIE cienaCesMplsStaticIngressTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.5	CienaGlobalState	read-only	Specifies the administrative status of the static encap tunnel.
CIE cienaCesMplsStaticIngressTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.6	CienaGlobalState	read-only	Specifies the operational status of the static encap tunnel.
IP cienaCesMplsStaticIngressTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.7	IpAddress	read-only	Destination IP address of the static encap tunnel. If not specified, the static encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the static encap tunnel entry is created.
INT cienaCesMplsStaticIngressTunnelLabel	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.8	INTEGER	read-only	The label for the static encap tunnel.
FCO cienaCesMplsStaticIngressTunnelFrmCosPolicy	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.9	FCosPolicy	read-only	Frame CoS policy of the static encap tunnel.
INT cienaCesMplsStaticIngressTunnelFrmCosMapId	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.10	INTEGER	read-only	The frame CoS map ID of the static encap tunnel. This value is valid if the frame CoS policy selected for the static encap tunnel is rcos-mapped. This value corresponds to the index cienaCesTceDpTsCosMapFcosMapId of the cienaCesTceDpTsCosMapFcosMapTable.
U32 cienaCesMplsStaticIngressTunnelFixedExp	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.11	Unsigned32	read-only	This object is deprecated and the new object to provide this information is cienaCesMplsStaticIngressTunnelFixedTC in this table.
TTL cienaCesMplsStaticIngressTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.12	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesMplsStaticIngressTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.13	Unsigned32	read-only	If the TTL policy for the static encap tunnel is fixed, then this object is the TTL value.
U32 cienaCesMplsStaticIngressTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.14	Unsigned32	read-only	The group ID of the tunnel group of which the static encap tunnel is a member.
INT cienaCesMplsStaticIngressTunnelReversion	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.16	INTEGER	read-only	Indicates whether tunnel reversion is turned on/off for this encap tunnel.
INT cienaCesMplsStaticIngressTunnelReversionTimeout	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.17	INTEGER	read-only	This object represents the tunnel reversion hold time in seconds before the primary encap tunnel switches back as active tunnel in its tunnel group.
STR cienaCesMplsStaticIngressTunnelPrimaryTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.18	DisplayString	read-only	This object represents the primary tunnel it is protecting, if this is a backup tunnel.
U32 cienaCesMplsStaticIngressTunnelFixedTC	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.19	Unsigned32	read-only	If the frame CoS policy for the static encap tunnel is fixed, this value is used for MPLS encapsulation.
INT cienaCesMplsStaticIngressTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.20	INTEGER	read-only	specifies the protection role of the static encap tunnel
INT cienaCesMplsStaticIngressTunnelProtectionState	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.21	INTEGER	read-only	specifies the protection status of the static encap tunnel
STR cienaCesMplsStaticIngressTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.22	DisplayString	read-only	This object represents the primary tunnel it is protecting, if this is a backup tunnel.
INT cienaCesMplsStaticIngressTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.23	INTEGER	read-only	This object represents Cos profile index
STR cienaCesMplsStaticIngressTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.24	DisplayString	read-only	Specifies the name of Cos profile
INT cienaCesMplsStaticIngressTunnelRecoveryDisjoint	1.3.6.1.4.1.1271.2.1.18.1.1.2.1.25	INTEGER	read-only	Specifies the type of Recovery Disjoint
cienaCesMplsDynamicIngressTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.3		not-accessible	The (conceptual) table listing the MPLS encap tunnels.
cienaCesMplsDynamicIngressTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.3.1		not-accessible	An entry in the dynamic encap tunnel table.
U32 cienaCesMplsDynamicIngressTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesMplsDynamicIngressTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.2	DisplayString	read-only	This represents the dynamic encap tunnel name.
INT cienaCesMplsDynamicIngressTunnelWeight	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.3	INTEGER	read-only	A parameter to select the order of precedence of encap tunnels during tunnel switchover or reversion (if tunnel reversion is enabled). A higher weight indicates higher preference during switchover or reversion.
U32 cienaCesMplsDynamicIngressTunnelLspId	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.4	Unsigned32	read-only	A unique index within a tunnel group.
IP cienaCesMplsDynamicIngressTunnelNextHopIp	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.5	IpAddress	read-only	Specifies the next hop IP address for the dynamic encap tunnel.
CIE cienaCesMplsDynamicIngressTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.6	CienaGlobalState	read-only	Specifies the administrative status of the dynamic encap tunnel.
CIE cienaCesMplsDynamicIngressTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.7	CienaGlobalState	read-only	Specifies the operational status of the dynamic encap tunnel.
IP cienaCesMplsDynamicIngressTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.8	IpAddress	read-only	Destination IP address of the dynamic encap tunnel. If not specified, the dynamic encap tunnel inherits the IP address of the tunnel group. This object cannot be modified once the dynamic encap tunnel entry is created.
INT cienaCesMplsDynamicIngressTunnelLabel	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.9	INTEGER	read-only	Label for the dynamic encap tunnel.
INT cienaCesMplsDynamicIngressTunnelFrmCosPolicy	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.10	INTEGER	read-only	Frame CoS policy of the dynamic encap tunnel.
INT cienaCesMplsDynamicIngressTunnelFrmCosMapId	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.11	INTEGER	read-only	The frame CoS map ID of the dynamic encap tunnel. This value is valid if the frame CoS policy selected for the dynamic encap tunnel is rcos-mapped. This value corresponds to the index cienaCesTceDpTsCosMapFcosMapId of the cienaCesTceDpTsCosMapFcosMapTable.
U32 cienaCesMplsDynamicIngressTunnelFixedExp	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.12	Unsigned32	read-only	This object is deprecated and the new object to provide this information is cienaCesMplsDynamicIngressTunnelFixedTC in this table.
U32 cienaCesMplsDynamicIngressTunnelSetupPriority	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.13	Unsigned32	read-only	Indicates the set up priority of the dynamic encap tunnel.
U32 cienaCesMplsDynamicIngressTunnelHoldPriority	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.14	Unsigned32	read-only	Indicates the holding priority of the dynamic encap tunnel.
INT cienaCesMplsDynamicIngressTunnelRecordRoute	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.15	INTEGER	read-only	Indicates whether or not an FRR (fast re-route) tunnel needs to be created for this dynamic encap tunnel.
INT cienaCesMplsDynamicIngressTunnelFastRoute	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.16	INTEGER	read-only	Indicates the fast route method for the dynamic encap tunnel. This object cannot be modified once the dynamic encap tunnel entry is created.
INT cienaCesMplsDynamicIngressTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.17	INTEGER	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesMplsDynamicIngressTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.18	Unsigned32	read-only	If the TTL policy for the dynamic encap tunnel is fixed, this object is the TTL value.
U32 cienaCesMplsDynamicIngressTunnelPathIndex	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.19	Unsigned32	read-only	Index into the cienaCesmplsTunnelPathTable entry that specifies the explicit route hops for this dynamic encap tunnel.
STR cienaCesMplsDynamicIngressTunnelPathName	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.20	DisplayString	read-only	The path name corresponding to the pathIndex object.
U32 cienaCesMplsDynamicIngressTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.21	Unsigned32	read-only	The group id of the tunnel group of which the dynamic encap tunnel is a member.
NUM cienaCesMplsDynamicIngressTunnelResourcePointer	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.23	RowPointer	read-only	The OID must be one of the entries in mplsTunnelResourceTable.
INT cienaCesMplsDynamicIngressTunnelReversion	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.24	INTEGER	read-only	Indicates whether tunnel reversion is turned on/off for this encap tunnel.
INT cienaCesMplsDynamicIngressTunnelReversionTimeout	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.25	INTEGER	read-only	This object represents the tunnel reversion hold time in seconds before the primary encap tunnel switches back as active tunnel in its tunnel group.
STR cienaCesMplsDynamicIngressTunnelBandwidthProfile	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.26	DisplayString	read-only	This object represents the bandwidth profile attached to this tunnel.
STR cienaCesMplsDynamicIngressTunnelPrimaryTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.27	DisplayString	read-only	This object represents the primary tunnel it is protecting, if this is a backup tunnel.
U32 cienaCesMplsDynamicIngressTunnelFixedTC	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.28	Unsigned32	read-only	If the frame CoS policy for the dynamic encap tunnel is fixed, this value is used for MPLS encapsulation.
INT cienaCesMplsDynamicIngressTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.29	INTEGER	read-only	specifies the protection role of the static encap tunnel
INT cienaCesMplsDynamicIngressTunnelProtectionState	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.30	INTEGER	read-only	specifies the protection status of the static encap tunnel
STR cienaCesMplsDynamicIngressTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.31	DisplayString	read-only	This object represents the primary tunnel it is protecting, if this is a backup tunnel.
INT cienaCesMplsDynamicIngressTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.32	INTEGER	read-only	This object represents Cos profile index
STR cienaCesMplsDynamicIngressTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.1.3.1.33	DisplayString	read-only	Specifies the name of Cos profile
cienaCesMplsStaticEgressTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.4		not-accessible	The (conceptual) table listing the MPLS decap tunnels.
cienaCesMplsStaticEgressTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.4.1		not-accessible	An entry in the static decap tunnel table.
U32 cienaCesMplsStaticEgressTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.4.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesMplsStaticEgressTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.4.1.2	DisplayString	read-only	This represents the decap tunnel name.
CIE cienaCesMplsStaticEgressTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.4.1.3	CienaGlobalState	read-only	Administrative status of the static decap tunnel.
CIE cienaCesMplsStaticEgressTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.4.1.4	CienaGlobalState	read-only	Indicates the operational status of the static decap tunnel.
IP cienaCesMplsStaticEgressTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.4.1.5	IpAddress	read-only	Source IP address of the static decap tunnel. This object cannot be modified once the static decap tunnel entry is created.
U32 cienaCesMplsStaticEgressTunnelLabel	1.3.6.1.4.1.1271.2.1.18.1.1.4.1.6	Unsigned32	read-only	Indicates the label of the static decap tunnel.
cienaCesMplsDynamicEgressTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.5		not-accessible	The (conceptual) table listing the MPLS dynamic decap tunnels.
cienaCesMplsDynamicEgressTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.5.1		not-accessible	An entry in the dynamic decap tunnel table.
U32 cienaCesMplsDynamicEgressTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.5.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesMplsDynamicEgressTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.5.1.2	DisplayString	read-only	This represents the dynamic decap tunnel name.
CIE cienaCesMplsDynamicEgressTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.5.1.3	CienaGlobalState	read-only	Indicates the administrative status of the dynamic decap tunnel.
CIE cienaCesMplsDynamicEgressTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.5.1.4	CienaGlobalState	read-only	Indicates the operational status of the dynamic decap tunnel.
U32 cienaCesMplsDynamicEgressTunnelInstance	1.3.6.1.4.1.1271.2.1.18.1.1.5.1.5	Unsigned32	read-only	Indicates the LSP ID.
IP cienaCesMplsDynamicEgressTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.5.1.6	IpAddress	read-only	Source IP address of the dynamic decap tunnel.
IP cienaCesMplsDynamicEgressTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.5.1.7	IpAddress	read-only	Destination IP address of the dynamic decap tunnel.
U32 cienaCesMplsDynamicEgressTunnelLabel	1.3.6.1.4.1.1271.2.1.18.1.1.5.1.8	Unsigned32	read-only	Idicates the label of the dynamic decap tunnel.
cienaCesMplsStaticTransitTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.6		not-accessible	The (conceptual) table listing the MPLS static transit tunnels.
cienaCesMplsStaticTransitTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.6.1		not-accessible	An entry in the static transit tunnel table.
U32 cienaCesMplsStaticTransitTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesMplsStaticTransitTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.2	DisplayString	read-only	This represents the static transit tunnel name.
CIE cienaCesMplsStaticTransitTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.3	CienaGlobalState	read-only	Indicates the administrative status of the static transit tunnel.
CIE cienaCesMplsStaticTransitTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.4	CienaGlobalState	read-only	Indicates the operational status of the static transit tunnel.
IP cienaCesMplsStaticTransitTunnelNextHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.5	IpAddress	read-only	Next hop IP address of the static transit tunnel.
INT cienaCesMplsStaticTransitTunnelInLabel	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.6	INTEGER	read-only	Indicates the incoming label of the static transit tunnel.
INT cienaCesMplsStaticTransitTunnelOutLabel	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.7	INTEGER	read-only	Indicates the outgoing label of the static transit tunnel.
FCO cienaCesMplsStaticTransitTunnelFcosPolicy	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.8	FCosPolicy	read-only	Frame CoS policy of the static transit tunnel.
U32 cienaCesMplsStaticTransitTunnelFixedTc	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.9	Unsigned32	read-only	If frame CoS policy for the static transit tunnel is fixed, this value is used for MPLS encapsulation.
INT cienaCesMplsStaticTransitTunnelFrmCosMapId	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.10	INTEGER	read-only	The frame CoS map ID of the static transit tunnel. This value is valid if the frame cos policy selected for the static transit tunnel is rcos-mapped.
TTL cienaCesMplsStaticTransitTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.11	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesMplsStaticTransitTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.12	Unsigned32	read-only	If the TTL policy for the static transit tunnel is fixed, then this object is the TTL value.
FCO cienaCesMplsStaticTransitTunnelRcosPolicy	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.13	FCosPolicy	read-only	Resolved CoS policy of the static transit tunnel.
INT cienaCesMplsStaticTransitTunnelRCosMapId	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.14	INTEGER	read-only	The resolved CoS map ID of the static transit tunnel. This value is valid if the resolved CoS policy selected for the static transit tunnel is rcos-mapped.
INT cienaCesMplsStaticTransitTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.15	INTEGER	read-only	This object represents Cos profile index
STR cienaCesMplsStaticTransitTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.16	DisplayString	read-only	Specifies the name of Cos profile
IP cienaCesMplsStaticTransitTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.17	IpAddress	read-only	Source IP address of the static transit tunnel.
IP cienaCesMplsStaticTransitTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.18	IpAddress	read-only	Destination IP address of the static transit tunnel.
U32 cienaCesMplsStaticTransitTunnelIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.19	Unsigned32	read-only	The number of incoming packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesMplsStaticTransitTunnelOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.20	Unsigned32	read-only	The number of outgoing packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesMplsStaticTransitTunnelIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.21	Unsigned32	read-only	The number of incoming bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesMplsStaticTransitTunnelOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.1.6.1.22	Unsigned32	read-only	The number of outgoing bytes for the given transit tunnel. This object is supported only on specific platforms.
cienaCesMplsDynamicTransitTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.7		not-accessible	The (conceptual) table listing the MPLS dynamic transit tunnels.
cienaCesMplsDynamicTransitTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.7.1		not-accessible	An entry in the dynamic transit tunnel table.
U32 cienaCesMplsDynamicTransitTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesMplsDynamicTransitTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.2	DisplayString	read-only	This represents the dynamic transit tunnel name.
CIE cienaCesMplsDynamicTransitTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.3	CienaGlobalState	read-only	Indicates the administrative status of the dynamic transit tunnel.
CIE cienaCesMplsDynamicTransitTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.4	CienaGlobalState	read-only	Indicates the operational status of the dynamic transit tunnel.
INT cienaCesMplsDynamicTransitTunnelInLabel	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.5	INTEGER	read-only	Indicates the incoming label of the dynamic transit tunnel.
INT cienaCesMplsDynamicTransitTunnelOutLabel	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.6	INTEGER	read-only	Indicates the outgoing label of the dynamic transit tunnel.
IP cienaCesMplsDynamicTransitTunnelNextHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.7	IpAddress	read-only	Next hop IP address of the Dynamic transit tunnel.
IP cienaCesMplsDynamicTransitTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.8	IpAddress	read-only	Source IP address of the static transit tunnel.
IP cienaCesMplsDynamicTransitTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.9	IpAddress	read-only	Destination IP address of the static transit tunnel.
U32 cienaCesMplsDynamicTransitTunnelIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.10	Unsigned32	read-only	The number of incoming packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesMplsDynamicTransitTunnelOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.11	Unsigned32	read-only	The number of outgoing packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesMplsDynamicTransitTunnelIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.12	Unsigned32	read-only	The number of incoming bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesMplsDynamicTransitTunnelOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.1.7.1.13	Unsigned32	read-only	The number of outgoing bytes for the given transit tunnel. This object is supported only on specific platforms.
cienaCesMplsTunnelPath	1.3.6.1.4.1.1271.2.1.18.1.1.8
cienaCesMplsTunnelPathTable	1.3.6.1.4.1.1271.2.1.18.1.1.8.1		not-accessible	The (conceptual) table listing the MPLS tunnel paths. To create an entry in the tunnel path table, cienaCesMplsTunnelPathName and cienaCesMplsTunnelPathRowStatus must both be specified.
cienaCesMplsTunnelPathEntry	1.3.6.1.4.1.1271.2.1.18.1.1.8.1.1		not-accessible	An entry in the tunnel path table.
U32 cienaCesMplsTunnelPathIndex	1.3.6.1.4.1.1271.2.1.18.1.1.8.1.1.1	Unsigned32	not-accessible	A unique index in the path entry table.
STR cienaCesMplsTunnelPathName	1.3.6.1.4.1.1271.2.1.18.1.1.8.1.1.2	DisplayString	read-only	Name associated with the path.
C32 cienaCesMplsTunnelPathUseCountEx	1.3.6.1.4.1.1271.2.1.18.1.1.8.1.1.3	Counter32	read-only	Indicates the number of encap tunnels that are using this path.
cienaCesMplsTunnelPathHopTable	1.3.6.1.4.1.1271.2.1.18.1.1.8.2		not-accessible	The (conceptual) table listing the MPLS tunnel path hop. To create an entry in the path-hop table, cienaCesMplsTunnelPathHopIpAddr and cienaCesMplsTunnelPathHopRowStatus must both be specified.
cienaCesMplsTunnelPathHopEntry	1.3.6.1.4.1.1271.2.1.18.1.1.8.2.1		not-accessible	A tunnel hop entry.
U32 cienaCesMplsTunnelPathHopIndex	1.3.6.1.4.1.1271.2.1.18.1.1.8.2.1.1	Unsigned32	not-accessible	Unique index in the path hop table.
IP cienaCesMplsTunnelPathHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.8.2.1.2	IpAddress	read-only	IP address associated with this hop. This object cannot be modified once the path hop is created.
INT cienaCesMplsTunnelPathHopType	1.3.6.1.4.1.1271.2.1.18.1.1.8.2.1.3	INTEGER	read-only	Indidcates the hop type of the path member. This object cannot be modified once the path hop is created.
cienaCesMplsEncapTunnelNotif	1.3.6.1.4.1.1271.2.1.18.1.1.9
cienaCesMplsNotifEncapTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.9.1		not-accessible	Table of notification objects required for encap tunnel notification.
cienaCesMplsNotifEncapTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.9.1.1		not-accessible	An entry (conceptual row) in the cienaCesMplsNotifEncapTunnelTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesMplsNotifEncapTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.9.1.1.1	Unsigned32	accessible-for-notify	Tunnel index of the encap tunnel associated with the notification.
INT cienaCesMplsNotifEncapTunnelType	1.3.6.1.4.1.1271.2.1.18.1.1.9.1.1.2	INTEGER	accessible-for-notify	Encap tunnel type of the encap tunnel associated with the notification.
STR cienaCesMplsNotifEncapTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.9.1.1.3	DisplayString	accessible-for-notify	This represents the encap tunnel name.
CIE cienaCesMplsNotifEncapTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.9.1.1.4	CienaGlobalState	accessible-for-notify	Administrative state of the encap tunnel.
CIE cienaCesMplsNotifEncapTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.9.1.1.5	CienaGlobalState	accessible-for-notify	Operational state of the encap tunnel.
TUN cienaCesMplsNotifEncapTunnelOamFaulted	1.3.6.1.4.1.1271.2.1.18.1.1.9.1.1.6	TunnelOamFault	accessible-for-notify	Indication if the tunnel has Oam fault.
IP cienaCesMplsNotifEncapTunnelFaultedNodeId	1.3.6.1.4.1.1271.2.1.18.1.1.9.1.1.7	IpAddress	accessible-for-notify	IP address of the node with the AIS fault.
cienaCesMplsTransitTunnelNotif	1.3.6.1.4.1.1271.2.1.18.1.1.10
cienaCesMplsNotifTransitTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.10.1		not-accessible	Table of notification objects required for transit tunnel notification.
cienaCesMplsNotifTransitTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.10.1.1		not-accessible	An entry (conceptual row) in the cienaCesMplsNotifTransitTunnelTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesMplsNotifTransitTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.10.1.1.1	Unsigned32	accessible-for-notify	Tunnel index of the transit tunnel associated with the notification.
INT cienaCesMplsNotifTransitTunnelType	1.3.6.1.4.1.1271.2.1.18.1.1.10.1.1.2	INTEGER	accessible-for-notify	Transit tunnel type of the transit tunnel associated with the notification.
STR cienaCesMplsNotifTransitTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.10.1.1.3	DisplayString	accessible-for-notify	This represents the transit tunnel name.
CIE cienaCesMplsNotifTransitTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.10.1.1.4	CienaGlobalState	accessible-for-notify	Administrative state of the transit tunnel.
CIE cienaCesMplsNotifTransitTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.10.1.1.5	CienaGlobalState	accessible-for-notify	Operational state of the transit tunnel.
TUN cienaCesMplsNotifTransitTunnelOamFaulted	1.3.6.1.4.1.1271.2.1.18.1.1.10.1.1.6	TunnelOamFault	accessible-for-notify	Indication if the tunnel has Oam fault.
cienaCesMplsEncapTunnelGrpNotif	1.3.6.1.4.1.1271.2.1.18.1.1.11
cienaCesMplsNotifEncapTunnelGrpTable	1.3.6.1.4.1.1271.2.1.18.1.1.11.1		not-accessible	Table of notification objects required for encap tunnel group notification.
cienaCesMplsNotifEncapTunnelGrpEntry	1.3.6.1.4.1.1271.2.1.18.1.1.11.1.1		not-accessible	An entry (conceptual row) in the cienaCesMplsNotifEncapTunnelGrpTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesMplsNotifEncapTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.1.11.1.1.1	Unsigned32	accessible-for-notify	Tunnel group index of the encap tunnel associated with the notification.
STR cienaCesMplsNotifEncapTunnelGrpName	1.3.6.1.4.1.1271.2.1.18.1.1.11.1.1.2	DisplayString	accessible-for-notify	Tunnel group name of the encap tunnel associated with the notification.
U32 cienaCesMplsNotifEncapTunnelGrpActiveEncapTunlIndex	1.3.6.1.4.1.1271.2.1.18.1.1.11.1.1.3	Unsigned32	accessible-for-notify	Active Encap Tunnel index of the tunnel group associated with the notification.
STR cienaCesMplsNotifEncapTunnelGrpActiveEncapTunlName	1.3.6.1.4.1.1271.2.1.18.1.1.11.1.1.4	DisplayString	accessible-for-notify	Active Encap Tunnel name of the Tunnel group associated with the notification.
INT cienaCesMplsNotifEncapTunnelGrpActiveEncapTunlType	1.3.6.1.4.1.1271.2.1.18.1.1.11.1.1.5	INTEGER	accessible-for-notify	Encap tunnel type of the encap tunnel associated with the notification.
cienaCesMplsAssociatedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.12		not-accessible	The table listing the MPLS Associated tunnels.
cienaCesMplsAssociatedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.12.1		not-accessible	This represents an entry of the MPLS associated tunnel table.
U32 cienaCesMplsAssociatedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.1	Unsigned32	not-accessible	Unique index in the table. Specifies mpls associated tunnel index
STR cienaCesMplsAssociatedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.2	DisplayString	read-only	specifies mpls associated tunnel name.
STR cienaCesMplsAssociatedForwardTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.3	DisplayString	read-only	specifies associated forward tunnel.
STR cienaCesMplsAssociatedForwardTunnelType	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.4	DisplayString	read-only	specifies associated forward tunnel type.
STR cienaCesMplsAssociatedReverseTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.5	DisplayString	read-only	specifies associated reverse tunnel.
STR cienaCesMplsAssociatedReverseTunnelType	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.6	DisplayString	read-only	specifies associated reverse tunnel type.
IP cienaCesMplsAssociatedForwardTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.7	IpAddress	read-only	specifies associated mpls forward tunnel destination IP address
IP cienaCesMplsAssociatedDynamicTunnelSrcIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.8	IpAddress	read-only	specifies associated mpls reverse tunnel source IP address.
CIE cienaCesMplsAssociatedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.9	CienaGlobalState	read-only	Administrative status of associated tunnel.
CIE cienaCesMplsAssociatedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.10	CienaGlobalState	read-only	Operational status of associated tunnel.
CIE cienaCesMplsAssociatedForwardTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.11	CienaGlobalState	read-only	Operational status of associated forward tunnel.
CIE cienaCesMplsAssociatedReverseTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.12	CienaGlobalState	read-only	Operational status of associated reverse tunnel.
INT cienaCesMplsAssociatedProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.13	INTEGER	read-only	specifies the protection role of the associated tunnel
INT cienaCesMplsAssociatedProtectionState	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.14	INTEGER	read-only	specifies the protection status of the associated tunnel
STR cienaCesMplsAssociatedTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.15	DisplayString	read-only	This object represents the tunnel name it is protecting
CIE cienaCesMplsAssociatedBfdMonitoring	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.16	CienaGlobalState	read-only	Specifies status of BFD monitoring.
STR cienaCesMplsAssociatedBfdProfileName	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.17	DisplayString	read-only	This object represent BFD profile name.
STR cienaCesMplsAssociatedBfdSessionName	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.18	DisplayString	read-only	Specifies BFD session name.
INT cienaCesMplsAssociatedBfdSessionFaulted	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.19	INTEGER	read-only	Indicates if BFD is faulted.
U32 cienaCesMplsAssociatedBfdProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.1.12.1.20	Unsigned32	read-only	This represents the BFD profile index in the BFD profile table configured for this associated tunnel
cienaCesMplsTunnelARHopTable	1.3.6.1.4.1.1271.2.1.18.1.1.13		not-accessible	The mplsTunnelARHopTable is used to indicate the hops for an MPLS tunnel defined in mplsTunnelTable, as reported by the MPLS signalling protocol. Thus at a transit LSR, this table (if the table is supported and if the signaling protocol is recording actual route information) contains the actual route of the whole tunnel. If the signaling protocol is not recording the actual route, this table MAY report the information from the mplsTunnelHopTable or the mplsTunnelCHopTable. Each row in this table is indexed by mplsTunnelARHopListIndex. Each row also has a secondary index mplsTunnelARHopIndex, corresponding to the next hop that this row corresponds to. Please note that since the information necessary to build entries within this table is not provided by some MPLS signalling protocols, implementation of this table is optional. Furthermore, since the information in this table is actually provided by the MPLS signalling protocol after the path has been set-up, the entries in this table are provided only for observation, and hence, all variables in this table are accessible exclusively as read- only. Note also that the contencts of this table may change while it is being read because of re-routing activities. A network administrator may verify that the actual route read is consistent by reference to the mplsTunnelLastPathChange object.
cienaCesMplsTunnelARHopEntry	1.3.6.1.4.1.1271.2.1.18.1.1.13.1		not-accessible	An entry in this table represents a tunnel hop. An entry is created by the agent for signaled ERLSP set up by an MPLS signalling protocol.
U32 cienaMplsTunnelARHopListIndex	1.3.6.1.4.1.1271.2.1.18.1.1.13.1.1	Unsigned32	not-accessible	Primary index into this table identifying a particular recorded hop list.
U32 cienaMplsTunnelARHopIndex	1.3.6.1.4.1.1271.2.1.18.1.1.13.1.2	Unsigned32	not-accessible	Secondary index into this table identifying the particular hop.
INT cienaMplsTunnelARHopAddrType	1.3.6.1.4.1.1271.2.1.18.1.1.13.1.3	INTEGER	read-only	The Hop Address Type of this tunnel hop. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP.
IP cienaMplsTunnelARHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.1.13.1.4	IpAddress	read-only	The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelARHopAddrType. If mplsTunnelARHopAddrType is set to unnum(4), then this value contains the LSR Router ID of the unnumbered interface. Otherwise the agent SHOULD set this object to the zero-length string and the manager should ignore this object.
U32 cienaMplsTunnelARHopAddrUnnum	1.3.6.1.4.1.1271.2.1.18.1.1.13.1.5	Unsigned32	read-only	If mplsTunnelARHopAddrType is set to unnum(4), then this value will contain the interface identifier of the unnumbered interface for this hop. This object should be used in conjunction with mplsTunnelARHopIpAddr which would contain the LSR Router ID in this case. Otherwise the agent should set this object to zero-length string and the manager should ignore this.
U32 cienaMplsTunnelARHopLspId	1.3.6.1.4.1.1271.2.1.18.1.1.13.1.6	Unsigned32	read-only	If mplsTunnelARHopAddrType is set to lspid(5), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact.
cienaCesMplsAssociatedTunnelNotif	1.3.6.1.4.1.1271.2.1.18.1.1.14
cienaCesMplsNotifAssociatedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.1.14.1		not-accessible	Table of notification objects required for associated tunnel notification.
cienaCesMplsNotifAssociatedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.1.14.1.1		not-accessible	An entry (conceptual row) in the cienaCesMplsNotifAssociatedTunnelTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesMplsNotifAssociatedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.1.14.1.1.1	Unsigned32	accessible-for-notify	Tunnel index of the associated tunnel associated with the notification.
INT cienaCesMplsNotifAssociatedTunnelType	1.3.6.1.4.1.1271.2.1.18.1.1.14.1.1.2	INTEGER	accessible-for-notify	Associated tunnel type of the associated tunnel associated with the notification.
STR cienaCesMplsNotifAssociatedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.1.14.1.1.3	DisplayString	accessible-for-notify	This represents the associated tunnel name.
CIE cienaCesMplsNotifAssociatedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.1.14.1.1.4	CienaGlobalState	accessible-for-notify	Administrative state of the associated tunnel.
CIE cienaCesMplsNotifAssociatedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.1.14.1.1.5	CienaGlobalState	accessible-for-notify	Operational state of the associated tunnel.
TUN cienaCesMplsNotifAssociatedTunnelOamFaulted	1.3.6.1.4.1.1271.2.1.18.1.1.14.1.1.6	TunnelOamFault	accessible-for-notify	Indication if the tunnel has Oam fault.
IP cienaCesMplsNotifAssociatedTunnelFaultedNodeId	1.3.6.1.4.1.1271.2.1.18.1.1.14.1.1.7	IpAddress	accessible-for-notify	IP address of the node with the AIS fault.
cienaCesMplsCacInterfaceNotif	1.3.6.1.4.1.1271.2.1.18.1.1.15
cienaCesMplsNotifCacInterfaceTable	1.3.6.1.4.1.1271.2.1.18.1.1.15.1		not-accessible	Table of notification objects required for CAC interface notification.
cienaCesMplsNotifCacInterfaceEntry	1.3.6.1.4.1.1271.2.1.18.1.1.15.1.1		not-accessible	An entry (conceptual row) in the cienaCesMplsNotifCACInterfaceTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesMplsNotifCacInterfaceIndex	1.3.6.1.4.1.1271.2.1.18.1.1.15.1.1.1	Unsigned32	accessible-for-notify	CAC entry index associated with the notification.
U32 cienaCesMplsNotifCacInterfaceClassType	1.3.6.1.4.1.1271.2.1.18.1.1.15.1.1.2	Unsigned32	accessible-for-notify	CAC class type value of the associated interface associated with the notification.
STR cienaCesMplsNotifCacInterfaceName	1.3.6.1.4.1.1271.2.1.18.1.1.15.1.1.3	DisplayString	accessible-for-notify	This represents the associated interface name.
U32 cienaCesMplsNotifCacInterfaceThreshold	1.3.6.1.4.1.1271.2.1.18.1.1.15.1.1.4	Unsigned32	accessible-for-notify	Alarm threshold value of the associated interface associated with the notification.
cienaCesMplsClassProfileTable	1.3.6.1.4.1.1271.2.1.18.1.1.16		not-accessible	The (conceptual) table listing the MPLS Class Profiles.
cienaCesMplsClassProfileEntry	1.3.6.1.4.1.1271.2.1.18.1.1.16.1		not-accessible	This represents an entry for MPLS Class Profile.
U32 cienaCesMplsClassProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.1.16.1.1	Unsigned32	not-accessible	This represents the unique index for MPLS Class Profile.
STR cienaCesMplsClassProfileName	1.3.6.1.4.1.1271.2.1.18.1.1.16.1.2	DisplayString	read-only	This represents the MPLS Class Profile name.
CAC cienaCesMplsClassProfileCacPolicy	1.3.6.1.4.1.1271.2.1.18.1.1.16.1.3	CacPolicy	read-only	MPLS Class Profile Cac policy.
cienaCesMplsTEClassTypeTable	1.3.6.1.4.1.1271.2.1.18.1.1.17		not-accessible	The (conceptual) table listing the MPLS Class Types.
cienaCesMplsTEClassTypeEntry	1.3.6.1.4.1.1271.2.1.18.1.1.17.1		not-accessible	This represents an entry for MPLS Class Type.
U32 cienaCesMplsClassType	1.3.6.1.4.1.1271.2.1.18.1.1.17.1.1	Unsigned32	not-accessible	Indicates the MPLS Class Type value. Used as an Index in combination with MPLS Class Profile Index.
U32 cienaCesMplsClassTypeQueueGroupIndex	1.3.6.1.4.1.1271.2.1.18.1.1.17.1.2	Unsigned32	read-only	Indicates the queue group index associated with MPLS Class Type.
U32 cienaCesMplsClassTypeQueueGroupInstance	1.3.6.1.4.1.1271.2.1.18.1.1.17.1.3	Unsigned32	read-only	Indicates the instance for MPLS Class Type mapped to a particular queue group.
U32 cienaCesMplsClassTypeLom	1.3.6.1.4.1.1271.2.1.18.1.1.17.1.4	Unsigned32	read-only	Indicates the link multiplier value for the MPLS Class Type.
U32 cienaCesMplsClassTypeAlarmThreshold	1.3.6.1.4.1.1271.2.1.18.1.1.17.1.5	Unsigned32	read-only	Indicates the Alarm Threshold percentage (%) for MPLS Class Type.
cienaCesGmpls	1.3.6.1.4.1.1271.2.1.18.1.2
cienaCesGmplsStaticIngressUniDirTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.1		not-accessible	The (conceptual) table listing the MPLS static encap tunnels.
cienaCesGmplsStaticIngressUniDirTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.1.1		not-accessible	This represents an entry of the MPLS static encap TP unidirectional tunnel table.
U32 cienaCesGmplsStaticIngressUniDirTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.1	Unsigned32	not-accessible	Unique index in the table.
STR cienaCesGmplsStaticIngressUniDirTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.2	DisplayString	read-only	This represents the encap tunnel name. Tunnel names are common across static and dynamic.
IP cienaCesGmplsStaticIngressUniDirTunnelNextHopIp	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.3	IpAddress	read-only	Specifies the next hop IP address for the static encap tunnel.
IP cienaCesGmplsStaticIngressUniDirTunnelSrcIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.4	IpAddress	read-only	Source IP address of the static encap tunnel. If not specified, the static encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the static encap tunnel entry is created.
IP cienaCesGmplsStaticIngressUniDirTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.5	IpAddress	read-only	Destination IP address of the static encap tunnel. If not specified, the static encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the static encap tunnel entry is created.
CIE cienaCesGmplsStaticIngressUniDirTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.6	CienaGlobalState	read-only	Specifies the administrative status of the static encap tunnel.
CIE cienaCesGmplsStaticIngressUniDirTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.7	CienaGlobalState	read-only	Specifies the operational status of the static encap tunnel.
U32 cienaCesGmplsStaticIngressUniDirTunnelForwardOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.8	Unsigned32	read-only	The label for the static encap tunnel.
INT cienaCesGmplsStaticIngressUniDirTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.9	INTEGER	read-only	The label for the static encap tunnel.
STR cienaCesGmplsStaticIngressUniDirTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.10	DisplayString	read-only	Protection partner name of the static encap tunnel.
INT cienaCesGmplsStaticIngressUniDirTunnelProtectionState	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.11	INTEGER	read-only	Specifies the Protection status of the static encap tunnel.
TTL cienaCesGmplsStaticIngressUniDirTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.12	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsStaticIngressUniDirTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.13	Unsigned32	read-only	If the TTL policy for the static encap tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsStaticIngressUniDirTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.14	Unsigned32	read-only	The group ID of the tunnel group of which the static encap tunnel is a member.
INT cienaCesGmplsStaticIngressUniDirTunnelReversion	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.15	INTEGER	read-only	Indicates whether tunnel reversion is turned on/off for this encap tunnel.
U32 cienaCesGmplsStaticIngressUniDirTunnelReversionTimeout	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.16	Unsigned32	read-only	This object represents the tunnel reversion hold time in seconds before the primary encap tunnel switches back as active tunnel in its tunnel group.
INT cienaCesGmplsStaticIngressUniDirTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.17	INTEGER	read-only	This object represents Cos profile index
STR cienaCesGmplsStaticIngressUniDirTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.18	DisplayString	read-only	Specifies the name of Cos profile
INT cienaCesGmplsStaticIngressUniDirTunnelRecoveryDisjoint	1.3.6.1.4.1.1271.2.1.18.1.2.1.1.19	INTEGER	read-only	Specifies the type of Recovery Disjoint
cienaCesGmplsStaticIngressCoroutedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.2		not-accessible	The (conceptual) table listing the MPLS static encap tunnels.
cienaCesGmplsStaticIngressCoroutedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.2.1		not-accessible	This represents an entry of the MPLS static encap tunnel table.
U32 cienaCesGmplsStaticIngressCoroutedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.1	Unsigned32	not-accessible	Unique index in the table.
STR cienaCesGmplsStaticIngressCoroutedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.2	DisplayString	read-only	This represents the encap tunnel name. Tunnel names are common across static and dynamic.
IP cienaCesGmplsStaticIngressCoroutedTunnelNextHopIp	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.3	IpAddress	read-only	Specifies the next hop IP address for the static encap tunnel.
IP cienaCesGmplsStaticIngressCoroutedTunnelSrcIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.4	IpAddress	read-only	Source IP address of the static encap tunnel. If not specified, the static encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the static encap tunnel entry is created.
IP cienaCesGmplsStaticIngressCoroutedTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.5	IpAddress	read-only	Destination IP address of the static encap tunnel. If not specified, the static encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the static encap tunnel entry is created.
CIE cienaCesGmplsStaticIngressCoroutedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.6	CienaGlobalState	read-only	Specifies the administrative status of the static encap tunnel.
CIE cienaCesGmplsStaticIngressCoroutedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.7	CienaGlobalState	read-only	Specifies the operational status of the static encap tunnel.
U32 cienaCesGmplsStaticIngressCoroutedTunnelForwardOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.8	Unsigned32	read-only	The label for the static encap tunnel.
U32 cienaCesGmplsStaticIngressCoroutedTunnelReverseInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.9	Unsigned32	read-only	The label for the static encap tunnel.
INT cienaCesGmplsStaticIngressCoroutedTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.10	INTEGER	read-only	The label for the static encap tunnel.
STR cienaCesGmplsStaticIngressCoroutedTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.11	DisplayString	read-only	Protection partner name of the static encap tunnel.
INT cienaCesGmplsStaticIngressCoroutedTunnelProtectionState	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.12	INTEGER	read-only	Specifies the Protection status of the static encap tunnel.
TTL cienaCesGmplsStaticIngressCoroutedTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.13	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsStaticIngressCoroutedTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.14	Unsigned32	read-only	If the TTL policy for the static encap tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsStaticIngressCoroutedTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.15	Unsigned32	read-only	The group ID of the tunnel group of which the static encap tunnel is a member.
INT cienaCesGmplsStaticIngressCoroutedTunnelReversion	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.16	INTEGER	read-only	Indicates whether tunnel reversion is turned on/off for this encap tunnel.
U32 cienaCesGmplsStaticIngressCoroutedTunnelReversionTimeout	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.17	Unsigned32	read-only	This object represents the tunnel reversion hold time in seconds before the primary encap tunnel switches back as active tunnel in its tunnel group.
INT cienaCesGmplsStaticIngressCoroutedTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.18	INTEGER	read-only	This object represents Cos profile index
STR cienaCesGmplsStaticIngressCoroutedTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.19	DisplayString	read-only	Specifies the name of Cos profile
CIE cienaCesGmplsStaticIngressCoroutedTunnelBfdMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.20	CienaGlobalState	read-only	Specifies status of BFD monitoring.
STR cienaCesGmplsStaticIngressCoroutedTunnelBfdProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.21	DisplayString	read-only	This object represent BFD profile name.
STR cienaCesGmplsStaticIngressCoroutedTunnelBfdSessionName	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.22	DisplayString	read-only	Specifies BFD session name.
CIE cienaCesGmplsStaticIngressCoroutedTunnelAisMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.23	CienaGlobalState	read-only	Specifies status of AIS monitoring.
STR cienaCesGmplsStaticIngressCoroutedTunnelAisProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.24	DisplayString	read-only	This object represent AIS profile name.
INT cienaCesGmplsStaticIngressCoroutedTunnelBfdSessionFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.25	INTEGER	read-only	Indicates if BFD is faulted.
U32 cienaCesGmplsStaticIngressCoroutedTunnelBfdProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.26	Unsigned32	read-only	This represents the BFD profile index in the BFD profile table configured for this gmpls static ingress corouted tunnel
INT cienaCesGmplsStaticIngressCoroutedTunnelRecoveryDisjoint	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.27	INTEGER	read-only	Specifies the type of Recovery Disjoint
U32 cienaCesGmplsStaticIngressCoroutedTunnelNextHopIfNum	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.28	Unsigned32	read-only	This represents next hop interface number for this gmpls static ingress corouted tunnel
U32 cienaCesGmplsStaticIngressCoroutedTunnelLspId	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.29	Unsigned32	read-only	This represents LSP ID for this gmpls static ingress corouted tunnel
U32 cienaCesGmplsStaticIngressCoroutedTunnelSrcTunnelId	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.30	Unsigned32	read-only	This represents source tunnel ID for this gmpls static ingress corouted tunnel
U32 cienaCesGmplsStaticIngressCoroutedTunnelDestTunnelId	1.3.6.1.4.1.1271.2.1.18.1.2.2.1.31	Unsigned32	read-only	This represents destination tunnel ID for this gmpls static ingress corouted tunnel
cienaCesGmplsDynamicIngressUniDirTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.3		not-accessible	The (conceptual) table listing the MPLS Dynamic encap tunnels.
cienaCesGmplsDynamicIngressUniDirTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.3.1		not-accessible	This represents an entry of the MPLS Dynamic encap tunnel table.
U32 cienaCesGmplsDynamicIngressUniDirTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.1	Unsigned32	not-accessible	Unique index in the table.
STR cienaCesGmplsDynamicIngressUniDirTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.2	DisplayString	read-only	This represents the encap tunnel name. Tunnel names are common across Dynamic and dynamic.
U32 cienaCesMplsDynamicIngressUniDirTunnelLspId	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.3	Unsigned32	read-only	A unique index within a tunnel group.
IP cienaCesGmplsDynamicIngressUniDirTunnelNextHopIp	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.4	IpAddress	read-only	Specifies the next hop IP address for the Dynamic encap tunnel.
IP cienaCesGmplsDynamicIngressUniDirTunnelSrcIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.5	IpAddress	read-only	Source IP address of the Dynamic encap tunnel. If not specified, the Dynamic encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the Dynamic encap tunnel entry is created.
IP cienaCesGmplsDynamicIngressUniDirTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.6	IpAddress	read-only	Destination IP address of the Dynamic encap tunnel. If not specified, the Dynamic encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the Dynamic encap tunnel entry is created.
CIE cienaCesGmplsDynamicIngressUniDirTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.7	CienaGlobalState	read-only	Specifies the administrative status of the Dynamic encap tunnel.
CIE cienaCesGmplsDynamicIngressUniDirTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.8	CienaGlobalState	read-only	Specifies the operational status of the Dynamic encap tunnel.
U32 cienaCesGmplsDynamicIngressUniDirTunnelForwardOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.9	Unsigned32	read-only	The label for the Dynamic encap tunnel.
INT cienaCesGmplsDynamicIngressUniDirTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.10	INTEGER	read-only	The label for the Dynamic encap tunnel.
STR cienaCesGmplsDynamicIngressUniDirTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.11	DisplayString	read-only	Protection partner name of the Dynamic encap tunnel.
INT cienaCesGmplsDynamicIngressUniDirTunnelProtectionState	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.12	INTEGER	read-only	Specifies the Protection status of the Dynamic encap tunnel.
TTL cienaCesGmplsDynamicIngressUniDirTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.13	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsDynamicIngressUniDirTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.14	Unsigned32	read-only	If the TTL policy for the Dynamic encap tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsDynamicIngressUniDirTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.15	Unsigned32	read-only	The group ID of the tunnel group of which the Dynamic encap tunnel is a member.
INT cienaCesGmplsDynamicIngressUniDirTunnelReversion	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.16	INTEGER	read-only	Indicates whether tunnel reversion is turned on/off for this encap tunnel.
U32 cienaCesGmplsDynamicIngressUniDirTunnelReversionTimeout	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.17	Unsigned32	read-only	This object represents the tunnel reversion hold time in seconds before the primary encap tunnel switches back as active tunnel in its tunnel group.
U32 cienaCesGmplsDynamicIngressUniDirTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.18	Unsigned32	read-only	This object represents Cos profile index
STR cienaCesGmplsDynamicIngressUniDirTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.19	DisplayString	read-only	Specifies the name of Cos profile
INT cienaCesGmplsDynamicIngressUniDirTunnelRecordRoute	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.20	INTEGER	read-only	Indicates whether or not an FRR (fast re-route) tunnel needs to be created for this dynamic encap tunnel.
INT cienaCesGmplsDynamicIngressUniDirTunnelFastRoute	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.21	INTEGER	read-only	Indicates the fast route method for the dynamic encap tunnel. This object cannot be modified once the dynamic encap tunnel entry is created.
U32 cienaCesGmplsDynamicIngressUniDirTunnelSetupPriority	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.22	Unsigned32	read-only	Indicates the set up priority of the dynamic encap tunnel.
U32 cienaCesGmplsDynamicIngressUniDirTunnelHoldPriority	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.23	Unsigned32	read-only	Indicates the holding priority of the dynamic encap tunnel.
U32 cienaCesGmplsDynamicIngressUniDirTunnelPathIndex	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.24	Unsigned32	read-only	Index into the cienaCesmplsTunnelPathTable entry that specifies the explicit route hops for this dynamic encap tunnel.
STR cienaCesGmplsDynamicIngressUniDirTunnelPathName	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.25	DisplayString	read-only	The path name corresponding to the pathIndex object.
STR cienaCesGmplsDynamicIngressUniDirTunnelBandwidthProfile	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.26	DisplayString	read-only	This object represents the bandwidth profile attached to this tunnel.
NUM cienaCesGmplsDynamicIngressUniDirTunnelResourcePointer	1.3.6.1.4.1.1271.2.1.18.1.2.3.1.27	RowPointer	read-only	The OID must be one of the entries in mplsTunnelResourceTable.
cienaCesGmplsDynamicIngressCoroutedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.4		not-accessible	The (conceptual) table listing the MPLS Dynamic encap co-routed tunnels.
cienaCesGmplsDynamicIngressCoroutedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.4.1		not-accessible	This represents an entry of the MPLS Dynamic encap co-routed tunnel table.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.1	Unsigned32	not-accessible	Unique index in the table.
STR cienaCesGmplsDynamicIngressCoroutedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.2	DisplayString	read-only	This represents the encap tunnel name. Tunnel names are common across Dynamic and dynamic.
IP cienaCesGmplsDynamicIngressCoroutedTunnelNextHopIp	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.3	IpAddress	read-only	Specifies the next hop IP address for the Dynamic encap tunnel.
IP cienaCesGmplsDynamicIngressCoroutedTunnelSrcIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.4	IpAddress	read-only	Source IP address of the Dynamic encap tunnel. If not specified, the Dynamic encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the Dynamic encap tunnel entry is created.
IP cienaCesGmplsDynamicIngressCoroutedTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.5	IpAddress	read-only	Destination IP address of the Dynamic encap tunnel. If not specified, the Dynamic encap tunnel inherits the IP address of the tunnel-group. This object cannot be modified once the Dynamic encap tunnel entry is created.
CIE cienaCesGmplsDynamicIngressCoroutedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.6	CienaGlobalState	read-only	Specifies the administrative status of the Dynamic encap tunnel.
CIE cienaCesGmplsDynamicIngressCoroutedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.7	CienaGlobalState	read-only	Specifies the operational status of the Dynamic encap tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelForwardOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.8	Unsigned32	read-only	The label for the Dynamic encap tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelReverseInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.9	Unsigned32	read-only	The label for the Dynamic encap tunnel.
INT cienaCesGmplsDynamicIngressCoroutedTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.10	INTEGER	read-only	The label for the Dynamic encap tunnel.
STR cienaCesGmplsDynamicIngressCoroutedTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.11	DisplayString	read-only	Protection partner name of the Dynamic encap tunnel.
INT cienaCesGmplsDynamicIngressCoroutedTunnelProtectionState	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.12	INTEGER	read-only	Specifies the Protection status of the Dynamic encap tunnel.
TTL cienaCesGmplsDynamicIngressCoroutedTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.13	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.14	Unsigned32	read-only	If the TTL policy for the Dynamic encap tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.15	Unsigned32	read-only	The group ID of the tunnel group of which the Dynamic encap tunnel is a member.
INT cienaCesGmplsDynamicIngressCoroutedTunnelReversion	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.16	INTEGER	read-only	Indicates whether tunnel reversion is turned on/off for this encap tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelReversionTimeout	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.17	Unsigned32	read-only	This object represents the tunnel reversion hold time in seconds before the primary encap tunnel switches back as active tunnel in its tunnel group.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.18	Unsigned32	read-only	This object represents Cos profile index
STR cienaCesGmplsDynamicIngressCoroutedTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.19	DisplayString	read-only	Specifies the name of Cos profile
INT cienaCesGmplsDynamicIngressCoroutedTunnelRecordRoute	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.20	INTEGER	read-only	Indicates whether or not an FRR (fast re-route) tunnel needs to be created for this dynamic encap tunnel.
INT cienaCesGmplsDynamicIngressCoroutedTunnelFastRoute	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.21	INTEGER	read-only	Indicates the fast route method for the dynamic encap tunnel. This object cannot be modified once the dynamic encap tunnel entry is created.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelSetupPriority	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.22	Unsigned32	read-only	Indicates the set up priority of the dynamic encap tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelHoldPriority	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.23	Unsigned32	read-only	Indicates the holding priority of the dynamic encap tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelPathIndex	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.24	Unsigned32	read-only	Index into the cienaCesmplsTunnelPathTable entry that specifies the explicit route hops for this dynamic encap tunnel.
STR cienaCesGmplsDynamicIngressCoroutedTunnelPathName	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.25	DisplayString	read-only	The path name corresponding to the pathIndex object.
STR cienaCesGmplsDynamicIngressCoroutedTunnelBandwidthProfile	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.26	DisplayString	read-only	This object represents the bandwidth profile attached to this tunnel.
NUM cienaCesGmplsDynamicIngressCoroutedTunnelResourcePointer	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.27	RowPointer	read-only	The OID must be one of the entries in mplsTunnelResourceTable.
CIE cienaCesGmplsDynamicIngressCoroutedTunnelBfdMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.28	CienaGlobalState	read-only	Specifies status of BFD monitoring.
STR cienaCesGmplsDynamicIngressCoroutedTunnelBfdProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.29	DisplayString	read-only	This object represent BFD profile name.
STR cienaCesGmplsDynamicIngressCoroutedTunnelBfdSessionName	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.30	DisplayString	read-only	Specifies BFD session name.
INT cienaCesGmplsDynamicIngressCoroutedTunnelBfdSessionFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.31	INTEGER	read-only	Indicates if BFD is faulted.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelBfdProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.32	Unsigned32	read-only	This represents the BFD profile index in the BFD profile table configured for this gmpls dynamic ingress corouted tunnel
INT cienaCesGmplsDynamicIngressCoroutedTunnelAutoBackupEnable	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.33	INTEGER	read-only	Indicates if auto-backup is enabled for this tunnel and always remains 0 in case of backup tunnel.
MPL cienaCesGmplsDynamicIngressCoroutedTunnelLspReoptimization	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.34	MplsGlobalState	read-only	Indicates if Lsp-Reoptimization is enabled or disabled for this tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelLspReOptTimeInterval	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.35	Unsigned32	read-only	Indicates Lsp-Reoptimization Time interval(in minutes) for this tunnel and always remains 0 in case of backup tunnel.
NUM cienaCesGmplsDynamicIngressCoroutedTunnelPathDisjointType	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.36	PathDisjointType	read-only	Indicates path diversification criteria used for this tunnel. It can either be node based or srlg based or link based or combination.
NUM cienaCesGmplsDynamicIngressCoroutedTunnelPathDisjointMode	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.37	PathDisjointMode	read-only	Indicates mode used for path diversification for this tunnel .
MPL cienaCesGmplsDynamicIngressCoroutedTunnelAutoSizeEnable	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.38	MplsGlobalState	read-only	Indicates if auto-size is enabled for this tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelAutoSizeInterval	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.39	Unsigned32	read-only	Indicates auto-sizing interval(in minutes) for this tunnel and always remains 0 in case of backup tunnel.
AUT cienaCesGmplsDynamicIngressCoroutedTunnelAutoSizeFailureHdlr	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.40	AutoSizeFailHdlr	read-only	Indicates auto-sizing failure handler for this tunnel.
AUT cienaCesGmplsDynamicIngressCoroutedTunnelAutoSizeState	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.41	AutoSizeState	read-only	Indicates dynamic auto-sizing states for this tunnel.
AUT cienaCesGmplsDynamicIngressCoroutedTunnelAutoSizeMode	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.42	AutoSizeMode	read-only	Indicates auto-sizing mode for this tunnel.
MPL cienaCesGmplsDynamicIngressCoroutedTunnelMinBandwidth	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.43	MplsBitRate	read-only	Indicates auto-size minimum bandwidth(in kbps) for this tunnel and always remains 0 in case of backup tunnel.
MPL cienaCesGmplsDynamicIngressCoroutedTunnelMaxBandwidth	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.44	MplsBitRate	read-only	Indicates auto-size maximum bandwidth(in kbps) for this tunnel and always remains 0 in case of backup tunnel.
MPL cienaCesGmplsDynamicIngressCoroutedTunnelIncBandwidth	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.45	MplsBitRate	read-only	Indicates auto-size increment bandwidth(in kbps) for this tunnel and always remains 0 in case of backup tunnel.
MPL cienaCesGmplsDynamicIngressCoroutedTunnelCurBandwidth	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.46	MplsBitRate	read-only	Indicates auto-size current bandwidth(in kbps) for this tunnel.
MPL cienaCesGmplsDynamicIngressCoroutedTunnelReqBandwidth	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.47	MplsBitRate	read-only	Indicates auto-size requested bandwidth(in kbps) for this tunnel.
MPL cienaCesGmplsDynamicIngressCoroutedTunnelUsedBandwidth	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.48	MplsBitRate	read-only	Indicates auto-size used bandwidth(in kbps) for this tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelClassType	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.49	Unsigned32	read-only	Indicates the DSTE class type (CT0-CT7) mapped to this Tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelResourceIncludeAll	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.50	Unsigned32	read-only	Resource affinity Admin Color-Group which is applied in include-all colors mode to constrain path selection and always remains 0 in case of backup tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelResourceIncludeAny	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.51	Unsigned32	read-only	Resource affinity Admin Color-Group which is applied in include-any colors mode to constrain path selection and always remains 0 in case of backup tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedTunnelResourceExcludeAny	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.52	Unsigned32	read-only	Resource affinity Admin Color-Group which is applied in exclude-any colors mode to constrain path selection and always remains 0 in case of backup tunnel.
U32 cienaCesGmplsDynamicIngressCoroutedLspId	1.3.6.1.4.1.1271.2.1.18.1.2.4.1.53	Unsigned32	read-only	Indicates the Ingress LSP ID.
cienaCesGmplsStaticEgressUniDirTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.5		not-accessible	The (conceptual) table listing the MPLS decap tunnels.
cienaCesGmplsStaticEgressUniDirTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.5.1		not-accessible	An entry in the static decap tunnel table.
U32 cienaCesGmplsStaticEgressUniDirTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.5.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesGmplsStaticEgressUniDirTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.5.1.2	DisplayString	read-only	This represents the decap tunnel name.
CIE cienaCesGmplsStaticEgressUniDirTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.5.1.3	CienaGlobalState	read-only	Administrative status of the static decap tunnel.
CIE cienaCesGmplsStaticEgressUniDirTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.5.1.4	CienaGlobalState	read-only	Indicates the operational status of the static decap tunnel.
IP cienaCesGmplsStaticEgressUniDirTunnelPrevHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.5.1.5	IpAddress	read-only	Prev hop IP address of the static decap tunnel. This object cannot be modified once the static decap tunnel entry is created.
IP cienaCesGmplsStaticEgressUniDirTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.5.1.6	IpAddress	read-only	Source IP address of the static decap tunnel. This object cannot be modified once the static decap tunnel entry is created.
IP cienaCesGmplsStaticEgressUniDirTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.5.1.7	IpAddress	read-only	destination IP address of the static decap tunnel. This object cannot be modified once the static decap tunnel entry is created.
U32 cienaCesGmplsStaticEgressUniDirTunnelForwardInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.5.1.8	Unsigned32	read-only	Indicates the label of the static decap tunnel.
cienaCesGmplsStaticEgressCoroutedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.6		not-accessible	The (conceptual) table listing the MPLS decap tunnels.
cienaCesGmplsStaticEgressCoroutedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.6.1		not-accessible	An entry in the static decap tunnel table.
U32 cienaCesGmplsStaticEgressCoroutedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesGmplsStaticEgressCoroutedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.2	DisplayString	read-only	This represents the decap tunnel name.
CIE cienaCesGmplsStaticEgressCoroutedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.3	CienaGlobalState	read-only	Administrative status of the static decap tunnel.
CIE cienaCesGmplsStaticEgressCoroutedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.4	CienaGlobalState	read-only	Indicates the operational status of the static decap tunnel.
IP cienaCesGmplsStaticEgressCoroutedTunnelPrevHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.5	IpAddress	read-only	Prev hop IP address of the static decap tunnel. This object cannot be modified once the static decap tunnel entry is created.
IP cienaCesGmplsStaticEgressCoroutedTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.6	IpAddress	read-only	Source IP address of the static decap tunnel. This object cannot be modified once the static decap tunnel entry is created.
IP cienaCesGmplsStaticEgressCoroutedTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.7	IpAddress	read-only	destination IP address of the static decap tunnel. This object cannot be modified once the static decap tunnel entry is created.
U32 cienaCesGmplsStaticEgressCoroutedTunnelForwardInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.8	Unsigned32	read-only	Indicates the in label of the static decap tunnel.
U32 cienaCesGmplsStaticEgressCoroutedTunnelReverseOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.9	Unsigned32	read-only	Indicates the out label of the static decap tunnel.
INT cienaCesGmplsStaticEgressCoroutedTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.10	INTEGER	read-only	specifies protection tunnel role.
STR cienaCesGmplsStaticEgressCoroutedTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.11	DisplayString	read-only	Protection partner name of the static encap tunnel.
INT cienaCesGmplsStaticEgressCoroutedTunnelProtectionState	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.12	INTEGER	read-only	Specifies the Protection status of the static encap tunnel.
U32 cienaCesGmplsStaticEgressCoroutedTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.13	Unsigned32	read-only	The group ID of the tunnel group of which the Dynamic encap tunnel is a member.
INT cienaCesGmplsStaticEgressCoroutedTunnelReversion	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.14	INTEGER	read-only	Indicates whether tunnel reversion is turned on/off for this encap tunnel.
U32 cienaCesGmplsStaticEgressCoroutedTunnelReversionTimeout	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.15	Unsigned32	read-only	This object represents the tunnel reversion hold time in seconds before the primary encap tunnel switches back as active tunnel in its tunnel group.
U32 cienaCesGmplsStaticEgressCoroutedTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.16	Unsigned32	read-only	This object represents Cos profile index
STR cienaCesGmplsStaticEgressCoroutedTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.17	DisplayString	read-only	Specifies the name of Cos profile
CIE cienaCesGmplsStaticEgressCoroutedTunnelBfdMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.18	CienaGlobalState	read-only	Specifies status of BFD monitoring.
STR cienaCesGmplsStaticEgressCoroutedTunnelBfdProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.19	DisplayString	read-only	This object represent BFD profile name.
STR cienaCesGmplsStaticEgressCoroutedTunnelBfdSessionName	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.20	DisplayString	read-only	Specifies BFD session name.
CIE cienaCesGmplsStaticEgressCoroutedTunnelAisMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.21	CienaGlobalState	read-only	Specifies status of AIS monitoring.
STR cienaCesGmplsStaticEgressCoroutedTunnelAisProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.22	DisplayString	read-only	This object represent AIS profile name.
INT cienaCesGmplsStaticEgressCoroutedTunnelBfdSessionFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.23	INTEGER	read-only	Indicates if BFD is faulted.
U32 cienaCesGmplsStaticEgressCoroutedTunnelBfdProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.24	Unsigned32	read-only	This represents the BFD profile index in the BFD profile table configured for this gmpls static egress corouted tunnel
INT cienaCesGmplsStaticEgressCoroutedTunnelRecoveryDisjoint	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.25	INTEGER	read-only	Specifies the type of Recovery Disjoint
TTL cienaCesGmplsStaticEgressCoroutedTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.26	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsStaticEgressCoroutedTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.27	Unsigned32	read-only	If the TTL policy for the Dynamic encap tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsStaticEgressCoroutedTunnelPrevHopIfNum	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.28	Unsigned32	read-only	This represents previous hop interface number for this gmpls static egress corouted tunnel.
U32 cienaCesGmplsStaticEgressCoroutedTunnelLspId	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.29	Unsigned32	read-only	This represents LSP ID for this gmpls static egress corouted tunnel.
U32 cienaCesGmplsStaticEgressCoroutedTunnelSrcTunnelId	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.30	Unsigned32	read-only	This represents source tunnel ID for this gmpls static egress corouted tunnel.
U32 cienaCesGmplsStaticEgressCoroutedTunnelDestTunnelId	1.3.6.1.4.1.1271.2.1.18.1.2.6.1.31	Unsigned32	read-only	This represents source tunnel ID for this gmpls static egress corouted tunnel.
cienaCesGmplsDynamicEgressUniDirTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.7		not-accessible	The (conceptual) table listing the MPLS dynamic decap tunnels.
cienaCesGmplsDynamicEgressUniDirTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.7.1		not-accessible	An entry in the dynamic decap tunnel table.
U32 cienaCesGmplsDynamicEgressUniDirTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesGmplsDynamicEgressUniDirTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.2	DisplayString	read-only	This represents the dynamic decap tunnel name.
CIE cienaCesGmplsDynamicEgressUniDirTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.3	CienaGlobalState	read-only	Indicates the administrative status of the dynamic decap tunnel.
CIE cienaCesGmplsDynamicEgressUniDirTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.4	CienaGlobalState	read-only	Indicates the operational status of the dynamic decap tunnel.
U32 cienaCesGmplsDynamicEgressUniDirLspId	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.5	Unsigned32	read-only	Indicates the LSP ID.
IP cienaCesGmplsDynamicEgressUniDirTunnelPrevHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.6	IpAddress	read-only	Source IP address of the dynamic decap tunnel.
IP cienaCesGmplsDynamicEgressUniDirTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.7	IpAddress	read-only	Source IP address of the dynamic decap tunnel.
IP cienaCesGmplsDynamicEgressUniDirTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.8	IpAddress	read-only	Destination IP address of the dynamic decap tunnel.
U32 cienaCesGmplsDynamicEgressUniDirTunnelForwardInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.7.1.9	Unsigned32	read-only	Idicates the label of the dynamic decap tunnel.
cienaCesGmplsDynamicEgressCoroutedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.8		not-accessible	The (conceptual) table listing the MPLS dynamic decap tunnels.
cienaCesGmplsDynamicEgressCoroutedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.8.1		not-accessible	An entry in the dynamic decap tunnel table.
U32 cienaCesGmplsDynamicEgressCoroutedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesGmplsDynamicEgressCoroutedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.2	DisplayString	read-only	This represents the dynamic decap tunnel name.
CIE cienaCesGmplsDynamicEgressCoroutedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.3	CienaGlobalState	read-only	Indicates the administrative status of the dynamic decap tunnel.
CIE cienaCesGmplsDynamicEgressCoroutedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.4	CienaGlobalState	read-only	Indicates the operational status of the dynamic decap tunnel.
U32 cienaCesGmplsDynamicEgressCoroutedLspId	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.5	Unsigned32	read-only	Indicates the LSP ID.
IP cienaCesGmplsDynamicEgressCoroutedTunnelPrevHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.6	IpAddress	read-only	Prev hop IP address of the dynamic decap tunnel.
IP cienaCesGmplsDynamicEgressCoroutedTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.7	IpAddress	read-only	Source IP address of the dynamic decap tunnel.
IP cienaCesGmplsDynamicEgressCoroutedTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.8	IpAddress	read-only	Destination IP address of the dynamic decap tunnel.
U32 cienaCesGmplsDynamicEgressCoroutedTunnelForwardInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.9	Unsigned32	read-only	Idicates the label of the dynamic decap tunnel.
U32 cienaCesGmplsDynamicEgressCoroutedTunnelReverseOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.10	Unsigned32	read-only	Indicates the out label of the dynamic decap tunnel.
INT cienaCesGmplsDynamicEgressCoroutedTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.11	INTEGER	read-only	specifies role of this dynamic tunnel
STR cienaCesGmplsDynamicEgressCoroutedTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.12	DisplayString	read-only	Protection partner name of the dynamic encap tunnel.
INT cienaCesGmplsDynamicEgressCoroutedTunnelProtectionState	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.13	INTEGER	read-only	Specifies the Protection status of the static encap tunnel.
U32 cienaCesGmplsDynamicEgressCoroutedTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.14	Unsigned32	read-only	The group ID of the tunnel group of which the Dynamic encap tunnel is a member.
INT cienaCesGmplsDynamicEgressCoroutedTunnelReversion	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.15	INTEGER	read-only	Indicates whether tunnel reversion is turned on/off for this encap tunnel.
U32 cienaCesGmplsDynamicEgressCoroutedTunnelReversionTimeout	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.16	Unsigned32	read-only	This object represents the tunnel reversion hold time in seconds before the primary encap tunnel switches back as active tunnel in its tunnel group.
U32 cienaCesGmplsDynamicEgressCoroutedTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.17	Unsigned32	read-only	This object represents Cos profile index
STR cienaCesGmplsDynamicEgressCoroutedTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.18	DisplayString	read-only	Specifies the name of Cos profile
CIE cienaCesGmplsDynamicEgressCoroutedTunnelBfdMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.19	CienaGlobalState	read-only	This parameter indicates if BFD monitoring is enabled or disableb on tunnel
STR cienaCesGmplsDynamicEgressCoroutedTunnelBfdProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.20	DisplayString	read-only	It Indicates assigned BFD profile names to tunnel
STR cienaCesGmplsDynamicEgressCoroutedTunnelBfdSessionName	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.21	DisplayString	read-only	It Indicates BFD session names.
INT cienaCesGmplsDynamicEgressCoroutedTunnelBfdSessionFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.22	INTEGER	read-only	Specifies if BFD faulted
U32 cienaCesGmplsDynamicEgressCoroutedTunnelBfdProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.23	Unsigned32	read-only	This represents the BFD profile index in the BFD profile table configured for this gmpls dynamic egress corouted tunnel
TTL cienaCesGmplsDynamicEgressCoroutedTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.24	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsDynamicEgressCoroutedTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.8.1.25	Unsigned32	read-only	If the TTL policy for the Dynamic encap tunnel is fixed, then this object is the TTL value.
cienaCesGmplsStaticTransitUniDirTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.9		not-accessible	The (conceptual) table listing the MPLS static TransitUniDir tunnels.
cienaCesGmplsStaticTransitUniDirTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.9.1		not-accessible	An entry in the static TransitUniDir tunnel table.
U32 cienaCesGmplsStaticTransitUniDirTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesGmplsStaticTransitUniDirTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.2	DisplayString	read-only	This represents the static TransitUniDir tunnel name.
CIE cienaCesGmplsStaticTransitUniDirTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.3	CienaGlobalState	read-only	Indicates the administrative status of the static TransitUniDir tunnel.
CIE cienaCesGmplsStaticTransitUniDirTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.4	CienaGlobalState	read-only	Indicates the operational status of the static TransitUniDir tunnel.
IP cienaCesGmplsStaticTransitUniDirTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.5	IpAddress	read-only	Source IP address of the static TransitUniDir tunnel.
IP cienaCesGmplsStaticTransitUniDirTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.6	IpAddress	read-only	Destination IP address of the static TransitUniDir tunnel.
IP cienaCesGmplsStaticTransitUniDirTunnelNextHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.7	IpAddress	read-only	Next hop IP address of the static TransitUniDir tunnel.
IP cienaCesGmplsStaticTransitUniDirTunnelPrevHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.8	IpAddress	read-only	Previous hop IP address of the static TransitUniDir tunnel.
U32 cienaCesGmplsStaticTransitUniDirTunnelForwardInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.9	Unsigned32	read-only	Indicates the incoming label of the static TransitUniDir tunnel.
U32 cienaCesGmplsStaticTransitUniDirTunnelForwardOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.10	Unsigned32	read-only	Indicates the outgoing label of the static TransitUniDir tunnel.
TTL cienaCesGmplsStaticTransitUniDirTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.11	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsStaticTransitUniDirTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.12	Unsigned32	read-only	If the TTL policy for the static TransitUniDir tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsStaticTransitUniDirTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.13	Unsigned32	read-only	This object represents Cos profile index
STR cienaCesGmplsStaticTransitUniDirTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.14	DisplayString	read-only	Specifies the name of Cos profile
CIE cienaCesGmplsStaticTransitUniDirTunnelAisMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.15	CienaGlobalState	read-only	Specifies AIS monitoring's status.
STR cienaCesGmplsStaticTransitUniDirTunnelAisProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.16	DisplayString	read-only	This object contais AIS profile name.
U32 cienaCesGmplsStaticTransitUniDirTunnelIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.17	Unsigned32	read-only	The number of incoming packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitUniDirTunnelOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.18	Unsigned32	read-only	The number of outgoing packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitUniDirTunnelIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.19	Unsigned32	read-only	The number of incoming bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitUniDirTunnelOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.9.1.20	Unsigned32	read-only	The number of outgoing bytes for the given transit tunnel. This object is supported only on specific platforms.
cienaCesGmplsStaticTransitCoroutedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.10		not-accessible	The (conceptual) table listing the MPLS static TransitCorouted tunnels.
cienaCesGmplsStaticTransitCoroutedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.10.1		not-accessible	An entry in the static TransitCorouted tunnel table.
U32 cienaCesGmplsStaticTransitCoroutedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesGmplsStaticTransitCoroutedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.2	DisplayString	read-only	This represents the static TransitCorouted tunnel name.
CIE cienaCesGmplsStaticTransitCoroutedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.3	CienaGlobalState	read-only	Indicates the administrative status of the static TransitCorouted tunnel.
CIE cienaCesGmplsStaticTransitCoroutedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.4	CienaGlobalState	read-only	Indicates the operational status of the static TransitCorouted tunnel.
IP cienaCesGmplsStaticTransitCoroutedTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.5	IpAddress	read-only	Source IP address of the static TransitCorouted tunnel.
IP cienaCesGmplsStaticTransitCoroutedTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.6	IpAddress	read-only	Destination IP address of the static TransitCorouted tunnel.
IP cienaCesGmplsStaticTransitCoroutedTunnelNextHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.7	IpAddress	read-only	Next hop IP address of the static TransitCorouted tunnel.
IP cienaCesGmplsStaticTransitCoroutedTunnelPrevHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.8	IpAddress	read-only	Previous hop IP address of the static TransitCorouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelForwardInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.9	Unsigned32	read-only	Indicates the incoming label of the static TransitCorouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelForwardOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.10	Unsigned32	read-only	Indicates the outgoing label of the static TransitCorouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelReverseInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.11	Unsigned32	read-only	Indicates the incoming label of the static TransitCorouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelReverseOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.12	Unsigned32	read-only	Indicates the outgoing label of the static TransitCorouted tunnel.
TTL cienaCesGmplsStaticTransitCoroutedTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.13	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsStaticTransitCoroutedTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.14	Unsigned32	read-only	If the TTL policy for the static TransitCorouted tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsStaticTransitCoroutedTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.15	Unsigned32	read-only	This object represents Cos profile index
STR cienaCesGmplsStaticTransitCoroutedTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.16	DisplayString	read-only	Specifies the name of Cos profile
CIE cienaCesGmplsStaticTransitCoroutedTunnelAisMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.17	CienaGlobalState	read-only	specifies AIS monitoring.
STR cienaCesGmplsStaticTransitCoroutedTunnelAisProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.18	DisplayString	read-only	This object contains AIS profile name
U32 cienaCesGmplsStaticTransitCoroutedTunnelPrevHopIfNum	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.19	Unsigned32	read-only	This represents previous hop interface number for this gmpls transit corouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelNextHopIfNum	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.20	Unsigned32	read-only	This represents next hop interface number for this gmpls transit corouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelLspId	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.21	Unsigned32	read-only	This represents LSP ID for this gmpls transit corouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelSrcTunnelId	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.22	Unsigned32	read-only	This represents source tunnel ID for this gmpls transit corouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelDestTunnelId	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.23	Unsigned32	read-only	This represents destination tunnel ID for this gmpls transit corouted tunnel.
U32 cienaCesGmplsStaticTransitCoroutedTunnelIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.24	Unsigned32	read-only	The number of incoming packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitCoroutedTunnelOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.25	Unsigned32	read-only	The number of outgoing packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitCoroutedTunnelIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.26	Unsigned32	read-only	The number of incoming bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitCoroutedTunnelOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.27	Unsigned32	read-only	The number of outgoing bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitCoroutedTunnelReverseIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.28	Unsigned32	read-only	The number of reverse direction incoming packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitCoroutedTunnelReverseOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.29	Unsigned32	read-only	The number of reverse direction outgoing packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitCoroutedTunnelReverseIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.30	Unsigned32	read-only	The number of reverse direction incoming bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsStaticTransitCoroutedTunnelReverseOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.10.1.31	Unsigned32	read-only	The number of reverse direction outgoing bytes for the given transit tunnel. This object is supported only on specific platforms.
cienaCesGmplsDynamicTransitUniDirTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.11		not-accessible	The (conceptual) table listing the MPLS Dynamic TransitUniDir tunnels.
cienaCesGmplsDynamicTransitUniDirTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.11.1		not-accessible	An entry in the Dynamic TransitUniDir tunnel table.
U32 cienaCesGmplsDynamicTransitUniDirTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesGmplsDynamicTransitUniDirTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.2	DisplayString	read-only	This represents the Dynamic TransitUniDir tunnel name.
CIE cienaCesGmplsDynamicTransitUniDirTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.3	CienaGlobalState	read-only	Indicates the administrative status of the Dynamic TransitUniDir tunnel.
CIE cienaCesGmplsDynamicTransitUniDirTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.4	CienaGlobalState	read-only	Indicates the operational status of the Dynamic TransitUniDir tunnel.
IP cienaCesGmplsDynamicTransitUniDirTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.5	IpAddress	read-only	Source IP address of the Dynamic TransitUniDir tunnel.
IP cienaCesGmplsDynamicTransitUniDirTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.6	IpAddress	read-only	Destination IP address of the Dynamic TransitUniDir tunnel.
IP cienaCesGmplsDynamicTransitUniDirTunnelNextHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.7	IpAddress	read-only	Next hop IP address of the Dynamic TransitUniDir tunnel.
U32 cienaCesGmplsDynamicTransitUniDirTunnelForwardInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.8	Unsigned32	read-only	Indicates the incoming label of the Dynamic TransitUniDir tunnel.
U32 cienaCesGmplsDynamicTransitUniDirTunnelForwardOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.9	Unsigned32	read-only	Indicates the outgoing label of the Dynamic TransitUniDir tunnel.
TTL cienaCesGmplsDynamicTransitUniDirTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.10	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsDynamicTransitUniDirTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.11	Unsigned32	read-only	If the TTL policy for the Dynamic TransitUniDir tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsDynamicTransitUniDirTunnelIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.12	Unsigned32	read-only	The number of incoming packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitUniDirTunnelOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.13	Unsigned32	read-only	The number of outgoing packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitUniDirTunnelIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.14	Unsigned32	read-only	The number of incoming bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitUniDirTunnelOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.11.1.15	Unsigned32	read-only	The number of outgoing bytes for the given transit tunnel. This object is supported only on specific platforms.
cienaCesGmplsDynamicTransitCoroutedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.12		not-accessible	The (conceptual) table listing the MPLS Dynamic TransitCoRouted tunnels.
cienaCesGmplsDynamicTransitCoroutedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.12.1		not-accessible	An entry in the Dynamic TransitCorouted tunnel table.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.1	Unsigned32	not-accessible	This represents the unique index in the table.
STR cienaCesGmplsDynamicTransitCoroutedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.2	DisplayString	read-only	This represents the Dynamic TransitCorouted tunnel name.
CIE cienaCesGmplsDynamicTransitCoroutedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.3	CienaGlobalState	read-only	Indicates the administrative status of the Dynamic TransitCorouted tunnel.
CIE cienaCesGmplsDynamicTransitCoroutedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.4	CienaGlobalState	read-only	Indicates the operational status of the Dynamic TransitCorouted tunnel.
IP cienaCesGmplsDynamicTransitCoroutedTunnelSourceIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.5	IpAddress	read-only	Source IP address of the Dynamic TransitCorouted tunnel.
IP cienaCesGmplsDynamicTransitCoroutedTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.6	IpAddress	read-only	Destination IP address of the Dynamic TransitCorouted tunnel.
IP cienaCesGmplsDynamicTransitCoroutedTunnelNextHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.7	IpAddress	read-only	Next hop IP address of the Dynamic TransitCorouted tunnel.
IP cienaCesGmplsDynamicTransitCoroutedTunnelPrevHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.8	IpAddress	read-only	Previous hop IP address of the Dynamic TransitCorouted tunnel.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelForwardInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.9	Unsigned32	read-only	Indicates the incoming label of the Dynamic TransitCorouted tunnel.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelForwardOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.10	Unsigned32	read-only	Indicates the outgoing label of the Dynamic TransitCorouted tunnel.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelReverseInLabel	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.11	Unsigned32	read-only	Indicates the incoming label of the Dynamic TransitCorouted tunnel.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelReverseOutLabel	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.12	Unsigned32	read-only	Indicates the outgoing label of the Dynamic TransitCorouted tunnel.
TTL cienaCesGmplsDynamicTransitCoroutedTunnelTTLPolicy	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.13	TTLPolicy	read-only	Specifies whether TTL is fixed or inherited from the frame.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelFixedTTL	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.14	Unsigned32	read-only	If the TTL policy for the Dynamic TransitCorouted tunnel is fixed, then this object is the TTL value.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.15	Unsigned32	read-only	The number of incoming packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.16	Unsigned32	read-only	The number of outgoing packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.17	Unsigned32	read-only	The number of incoming bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.18	Unsigned32	read-only	The number of outgoing bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelReverseIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.19	Unsigned32	read-only	The number of reverse incoming packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelReverseOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.20	Unsigned32	read-only	The number of reverse outgoing packets for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelReverseIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.21	Unsigned32	read-only	The number of reverse incoming bytes for the given transit tunnel. This object is supported only on specific platforms.
U32 cienaCesGmplsDynamicTransitCoroutedTunnelReverseOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.2.12.1.22	Unsigned32	read-only	The number of reverse outgoing bytes for the given transit tunnel. This object is supported only on specific platforms.
cienaCesGmplsAssociatedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.13		not-accessible	The (conceptual) table listing the Gmpls Associated tunnels.
cienaCesGmplsAssociatedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.13.1		not-accessible	This represents an entry of the Gmpls static encap tunnel table.
U32 cienaCesGmplsAssociatedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.1	Unsigned32	not-accessible	Unique tunnel index in the table.
STR cienaCesGmplsAssociatedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.2	DisplayString	read-only	specifies Gmpls associated tunnel name.
STR cienaCesGmplsAssociatedForwardTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.3	DisplayString	read-only	specifies associated forward tunnel.
STR cienaCesGmplsAssociatedForwardTunnelType	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.4	DisplayString	read-only	specifies associated forward tunnel type.
STR cienaCesGmplsAssociatedReverseTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.5	DisplayString	read-only	specifies associated reverse tunnel.
STR cienaCesGmplsAssociatedReverseTunnelType	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.6	DisplayString	read-only	specifies associated reverse tunnel type.
IP cienaCesGmplsAssociatedForwardTunnelDestIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.7	IpAddress	read-only	specifies associated Gmpls forward tunnel destination IP address
IP cienaCesGmplsAssociatedDynamicTunnelSrcIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.8	IpAddress	read-only	specifies associated Gmpls reverse tunnel source IP address.
CIE cienaCesGmplsAssociatedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.9	CienaGlobalState	read-only	Administrator status of associated tunnel.
CIE cienaCesGmplsAssociatedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.10	CienaGlobalState	read-only	Operational status of associated tunnel.
CIE cienaCesGmplsAssociatedForwardTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.11	CienaGlobalState	read-only	Operational status of associated forward tunnel.
CIE cienaCesGmplsAssociatedReverseTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.12	CienaGlobalState	read-only	Operational status of associated reverse tunnel.
INT cienaCesGmplsAssociatedProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.13	INTEGER	read-only	specifies the protection role of the associated tunnel
INT cienaCesGmplsAssociatedProtectionState	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.14	INTEGER	read-only	specifies the protection status of the associated tunnel
STR cienaCesGmplsAssociatedTunnelProtectionPartnerName	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.15	DisplayString	read-only	This object represents the tunnel name it is protecting
CIE cienaCesGmplsAssociatedBfdMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.16	CienaGlobalState	read-only	Specifies status of BFD monitoring.
STR cienaCesGmplsAssociatedBfdProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.17	DisplayString	read-only	This object represent BFD profile name.
STR cienaCesGmplsAssociatedBfdSessionName	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.18	DisplayString	read-only	Specifies BFD session name.
CIE cienaCesGmplsAssociatedAisMonitoring	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.19	CienaGlobalState	read-only	Specifies status of AIS monitoring.
STR cienaCesGmplsAssociatedAisProfileName	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.20	DisplayString	read-only	This object represent BFD profile name.
INT cienaCesGmplsAssociatedBfdSessionFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.21	INTEGER	read-only	Specifies BFD session error code.
U32 cienaCesGmplsAssociatedBfdProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.2.13.1.22	Unsigned32	read-only	This represents the BFD profile index in the BFD profile table configured for this gmpls associated tunnel
cienaCesGmplsTunnelARHopTable	1.3.6.1.4.1.1271.2.1.18.1.2.14		not-accessible	The GmplsTunnelARHopTable is used to indicate the hops for an Gmpls tunnel defined in GmplsTunnelTable, as reported by the Gmpls signalling protocol. Thus at a transit LSR, this table (if the table is supported and if the signaling protocol is recording actual route information) contains the actual route of the whole tunnel. If the signaling protocol is not recording the actual route, this table MAY report the information from the GmplsTunnelHopTable or the GmplsTunnelCHopTable. Each row in this table is indexed by GmplsTunnelARHopListIndex. Each row also has a secondary index GmplsTunnelARHopIndex, corresponding to the next hop that this row corresponds to. Please note that since the information necessary to build entries within this table is not provided by some Gmpls signalling protocols, implementation of this table is optional. Furthermore, since the information in this table is actually provided by the Gmpls signalling protocol after the path has been set-up, the entries in this table are provided only for observation, and hence, all variables in this table are accessible exclusively as read- only. Note also that the contencts of this table may change while it is being read because of re-routing activities. A network administrator may verify that the actual route read is consistent by reference to the GmplsTunnelLastPathChange object.
cienaCesGmplsTunnelARHopEntry	1.3.6.1.4.1.1271.2.1.18.1.2.14.1		not-accessible	An entry in this table represents a tunnel hop. An entry is created by the agent for signaled ERLSP set up by an Gmpls signalling protocol.
U32 cienaGmplsTunnelARHopListIndex	1.3.6.1.4.1.1271.2.1.18.1.2.14.1.1	Unsigned32	not-accessible	Primary index into this table identifying a particular recorded hop list.
U32 cienaGmplsTunnelARHopIndex	1.3.6.1.4.1.1271.2.1.18.1.2.14.1.2	Unsigned32	not-accessible	Secondary index into this table identifying the particular hop.
INT cienaGmplsTunnelARHopAddrType	1.3.6.1.4.1.1271.2.1.18.1.2.14.1.3	INTEGER	read-only	The Hop Address Type of this tunnel hop. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP.
IP cienaGmplsTunnelARHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.2.14.1.4	IpAddress	read-only	The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding GmplsTunnelARHopAddrType. If GmplsTunnelARHopAddrType is set to unnum(4), then this value contains the LSR Router ID of the unnumbered interface. Otherwise the agent SHOULD set this object to the zero-length string and the manager should ignore this object.
U32 cienaGmplsTunnelARHopAddrUnnum	1.3.6.1.4.1.1271.2.1.18.1.2.14.1.5	Unsigned32	read-only	If GmplsTunnelARHopAddrType is set to unnum(4), then this value will contain the interface identifier of the unnumbered interface for this hop. This object should be used in conjunction with GmplsTunnelARHopIpAddr which would contain the LSR Router ID in this case. Otherwise the agent should set this object to zero-length string and the manager should ignore this.
U32 cienaGmplsTunnelARHopLspId	1.3.6.1.4.1.1271.2.1.18.1.2.14.1.6	Unsigned32	read-only	If GmplsTunnelARHopAddrType is set to lspid(5), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact.
cienaCesGmplsEncapTunnelNotif	1.3.6.1.4.1.1271.2.1.18.1.2.15
cienaCesGmplsNotifEncapTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.15.1		not-accessible	Table of notification objects required for encap tunnel notification.
cienaCesGmplsNotifEncapTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1		not-accessible	An entry (conceptual row) in the cienaCesGmplsNotifEncapTunnelTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesGmplsNotifEncapTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.1	Unsigned32	accessible-for-notify	Tunnel index of the encap tunnel associated with the notification.
INT cienaCesGmplsNotifEncapTunnelType	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.2	INTEGER	accessible-for-notify	Encap tunnel type of the encap tunnel associated with the notification.
STR cienaCesGmplsNotifEncapTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.3	DisplayString	accessible-for-notify	This represents the encap tunnel name.
CIE cienaCesGmplsNotifEncapTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.4	CienaGlobalState	accessible-for-notify	Administrative state of the encap tunnel.
CIE cienaCesGmplsNotifEncapTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.5	CienaGlobalState	accessible-for-notify	Operational state of the encap tunnel.
TUN cienaCesGmplsNotifEncapTunnelAisFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.6	TunnelAisFault	accessible-for-notify	This is replaced by cienaCesGmplsNotifOamTunnelAisFaulted.
IP cienaCesGmplsNotifEncapTunnelFaultedNodeId	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.7	IpAddress	accessible-for-notify	IP address of the node with the AIS fault.
IP cienaCesGmplsNotifEncapTunnelFarEndLerId	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.8	IpAddress	accessible-for-notify	IP address of the far end LER for the tunne with the AIS fault.
INT cienaCesGmplsNotifEncapTunnelResult	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.9	INTEGER	accessible-for-notify	specifies the result of encap tunnel auto sizing/MBB.
INT cienaCesGmplsNotifEncapTunnelProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.10	INTEGER	accessible-for-notify	specifies the protection role of the dynamic encap tunnel.
U32 cienaCesGmplsNotifEncapTunnelRequestedBw	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.11	Unsigned32	accessible-for-notify	specifies the requested bandwidth of the dynamic encap tunnel.
U32 cienaCesGmplsNotifEncapTunnelOperationalBw	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.12	Unsigned32	accessible-for-notify	specifies the operational bandwidth of the dynamic encap tunnel.
INT cienaCesGmplsNotifEncapTunnelMbbParentApp	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.13	INTEGER	accessible-for-notify	specifies the parent application using MBB of the dynamic encap tunnel.
TUN cienaCesGmplsNotifEncapTunnelOamFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.15.1.1.14	TunnelOamFault	accessible-for-notify	Indication if the tunnel has Oam fault.
cienaCesGmplsDecapTunnelNotif	1.3.6.1.4.1.1271.2.1.18.1.2.16
cienaCesGmplsNotifDecapTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.16.1		not-accessible	Table of notification objects required for decap tunnel notification.
cienaCesGmplsNotifDecapTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1		not-accessible	An entry (conceptual row) in the cienaCesGmplsNotifDecapTunnelTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesGmplsNotifDecapTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.1	Unsigned32	accessible-for-notify	Tunnel index of the decap tunnel associated with the notification.
INT cienaCesGmplsNotifDecapTunnelType	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.2	INTEGER	accessible-for-notify	Decap tunnel type of the decap tunnel associated with the notification.
STR cienaCesGmplsNotifDecapTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.3	DisplayString	accessible-for-notify	This represents the decap tunnel name.
CIE cienaCesGmplsNotifDecapTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.4	CienaGlobalState	accessible-for-notify	Administrative state of the decap tunnel.
CIE cienaCesGmplsNotifDecapTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.5	CienaGlobalState	accessible-for-notify	Operational state of the decap tunnel.
TUN cienaCesGmplsNotifDecapTunnelAisFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.6	TunnelAisFault	accessible-for-notify	This is replaced by cienaCesGmplsNotifDecapTunnelOamFaulted.
IP cienaCesGmplsNotifDecapTunnelFaultedNodeId	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.7	IpAddress	accessible-for-notify	IP address of the node with the AIS fault.
IP cienaCesGmplsNotifDecapTunnelFarEndLerId	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.8	IpAddress	accessible-for-notify	IP address of the far end LER for the tunne with the AIS fault.
TUN cienaCesGmplsNotifDecapTunnelOamFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.16.1.1.9	TunnelOamFault	accessible-for-notify	Indication if the tunnel has Oam fault.
cienaCesGmplsTransitTunnelNotif	1.3.6.1.4.1.1271.2.1.18.1.2.17
cienaCesGmplsNotifTransitTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.17.1		not-accessible	Table of notification objects required for transit tunnel notification.
cienaCesGmplsNotifTransitTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.17.1.1		not-accessible	An entry (conceptual row) in the cienaCesGmplsNotifTransitTunnelTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesGmplsNotifTransitTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.17.1.1.1	Unsigned32	accessible-for-notify	Tunnel index of the transit tunnel associated with the notification.
INT cienaCesGmplsNotifTransitTunnelType	1.3.6.1.4.1.1271.2.1.18.1.2.17.1.1.2	INTEGER	accessible-for-notify	Transit tunnel type of the transit tunnel associated with the notification.
STR cienaCesGmplsNotifTransitTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.17.1.1.3	DisplayString	accessible-for-notify	This represents the transit tunnel name.
CIE cienaCesGmplsNotifTransitTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.17.1.1.4	CienaGlobalState	accessible-for-notify	Administrative state of the transit tunnel.
CIE cienaCesGmplsNotifTransitTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.17.1.1.5	CienaGlobalState	accessible-for-notify	Operational state of the transit tunnel.
TUN cienaCesGmplsNotifTransitTunnelOamFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.17.1.1.6	TunnelOamFault	accessible-for-notify	Indication if the tunnel has Oam fault.
cienaCesGmplsAssociatedTunnelNotif	1.3.6.1.4.1.1271.2.1.18.1.2.18
cienaCesGmplsNotifAssociatedTunnelTable	1.3.6.1.4.1.1271.2.1.18.1.2.18.1		not-accessible	Table of notification objects required for associated tunnel notification.
cienaCesGmplsNotifAssociatedTunnelEntry	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1		not-accessible	An entry (conceptual row) in the cienaCesGmplsNotifAssociatedTunnelTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesGmplsNotifAssociatedTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.1	Unsigned32	accessible-for-notify	Tunnel index of the associated tunnel associated with the notification.
INT cienaCesGmplsNotifAssociatedTunnelType	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.2	INTEGER	accessible-for-notify	Associated tunnel type of the associated tunnel associated with the notification.
STR cienaCesGmplsNotifAssociatedTunnelName	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.3	DisplayString	accessible-for-notify	This represents the associated tunnel name.
CIE cienaCesGmplsNotifAssociatedTunnelAdminState	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.4	CienaGlobalState	accessible-for-notify	Administrative state of the associated tunnel.
CIE cienaCesGmplsNotifAssociatedTunnelOperState	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.5	CienaGlobalState	accessible-for-notify	Operational state of the associated tunnel.
TUN cienaCesGmplsNotifAssociatedTunnelAisFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.6	TunnelAisFault	accessible-for-notify	Replaced by cienaCesGmplsNotifAssociatedTunnelOamFaulted
IP cienaCesGmplsNotifAssociatedTunnelFaultedNodeId	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.7	IpAddress	accessible-for-notify	IP address of the node with the AIS fault.
IP cienaCesGmplsNotifAssociatedTunnelFarEndLerId	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.8	IpAddress	accessible-for-notify	IP address of the far end LER for the tunne with the AIS fault.
TUN cienaCesGmplsNotifAssociatedTunnelOamFaulted	1.3.6.1.4.1.1271.2.1.18.1.2.18.1.1.9	TunnelOamFault	accessible-for-notify	Indication if the tunnel has Oam fault.
cienaCesGmplsEncapTunnelGrpNotif	1.3.6.1.4.1.1271.2.1.18.1.2.19
cienaCesGmplsNotifEncapTunnelGrpTable	1.3.6.1.4.1.1271.2.1.18.1.2.19.1		not-accessible	Table of notification objects required for encap tunnel group notification.
cienaCesGmplsNotifEncapTunnelGrpEntry	1.3.6.1.4.1.1271.2.1.18.1.2.19.1.1		not-accessible	An entry (conceptual row) in the cienaCesGmplsNotifEncapTunnelGrpTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesGmplsNotifEncapTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.2.19.1.1.1	Unsigned32	accessible-for-notify	Tunnel group index of the encap tunnel associated with the notification.
STR cienaCesGmplsNotifEncapTunnelGrpName	1.3.6.1.4.1.1271.2.1.18.1.2.19.1.1.2	DisplayString	accessible-for-notify	Tunnel group name of the encap tunnel associated with the notification.
U32 cienaCesGmplsNotifEncapTunnelGrpActiveEncapTunlIndex	1.3.6.1.4.1.1271.2.1.18.1.2.19.1.1.3	Unsigned32	accessible-for-notify	Active Encap Tunnel index of the tunnel group associated with the notification.
STR cienaCesGmplsNotifEncapTunnelGrpActiveEncapTunlName	1.3.6.1.4.1.1271.2.1.18.1.2.19.1.1.4	DisplayString	accessible-for-notify	Active Encap Tunnel name of the Tunnel group associated with the notification.
INT cienaCesGmplsNotifEncapTunnelGrpActiveEncapTunlType	1.3.6.1.4.1.1271.2.1.18.1.2.19.1.1.5	INTEGER	accessible-for-notify	Encap tunnel type of the encap tunnel associated with the notification.
cienaCesGmplsDecapTunnelGrpNotif	1.3.6.1.4.1.1271.2.1.18.1.2.20
cienaCesGmplsNotifDecapTunnelGrpTable	1.3.6.1.4.1.1271.2.1.18.1.2.20.1		not-accessible	Table of notification objects required for decap tunnel group notification.
cienaCesGmplsNotifDecapTunnelGrpEntry	1.3.6.1.4.1.1271.2.1.18.1.2.20.1.1		not-accessible	An entry(conceptual row) in the cienaCesGmplsNotifDecapTunnelGrpTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesGmplsNotifDecapTunnelGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.2.20.1.1.1	Unsigned32	accessible-for-notify	Tunnel group index of the decap tunnel associated with the notification.
STR cienaCesGmplsNotifDecapTunnelGrpName	1.3.6.1.4.1.1271.2.1.18.1.2.20.1.1.2	DisplayString	accessible-for-notify	Tunnel group name of the decap tunnel associated with the notification.
U32 cienaCesGmplsNotifDecapTunnelGrpActiveDecapTunlIndex	1.3.6.1.4.1.1271.2.1.18.1.2.20.1.1.3	Unsigned32	accessible-for-notify	Active Decap Tunnel index of the tunnel group associated with the notification.
STR cienaCesGmplsNotifDecapTunnelGrpActiveDecapTunlName	1.3.6.1.4.1.1271.2.1.18.1.2.20.1.1.4	DisplayString	accessible-for-notify	Active Decap Tunnel name of the Tunnel group associated with the notification.
INT cienaCesGmplsNotifDecapTunnelGrpActiveDecapTunlType	1.3.6.1.4.1.1271.2.1.18.1.2.20.1.1.5	INTEGER	accessible-for-notify	Decap tunnel type of the decap tunnel associated with the notification.
cienaCesGmplsTunnelAisFaultErrorNotif	1.3.6.1.4.1.1271.2.1.18.1.2.21
cienaCesGmplsNotifTunnelAisFaultErrorTable	1.3.6.1.4.1.1271.2.1.18.1.2.21.1		not-accessible	Table of notification objects required for tunnel Ais Fault error notification.
cienaCesGmplsNotifTunnelAisFaultErrorEntry	1.3.6.1.4.1.1271.2.1.18.1.2.21.1.1		not-accessible	An entry (conceptual row) in the cienaCesGmplsNotifTunnelAisFaultErrorTable No Get, GetNext or Set is allowed on this table.
U32 cienaCesGmplsNotifTunnelDecapLabel	1.3.6.1.4.1.1271.2.1.18.1.2.21.1.1.1	Unsigned32	accessible-for-notify	Decap label associated with the notification.
STR cienaCesGmplsNotifTunnelErrorMsg	1.3.6.1.4.1.1271.2.1.18.1.2.21.1.1.2	DisplayString	accessible-for-notify	This represents the fault error message for decap label associated with the notification
cienaCesMplsGlobal	1.3.6.1.4.1.1271.2.1.18.1.3
cienaCesMplsAttrs	1.3.6.1.4.1.1271.2.1.18.1.3.1
U32 cienaCesMplsGlobalStaticAdminLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.3.1.1	Unsigned32	read-only	The beginning of the static administrative label range. There cannot be any overlap between static and dynamic label ranges. Setting this object does not become effective until the device is rebooted.
U32 cienaCesMplsGlobalStaticAdminLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.3.1.2	Unsigned32	read-only	The end of the static administrative label range. There cannot be any overlap between static and dynamic label ranges. Setting this object does not become effective until the device is rebooted.
U32 cienaCesMplsGlobalStaticOperLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.3.1.3	Unsigned32	read-only	The beginning of the static operational label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalStaticOperLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.3.1.4	Unsigned32	read-only	The end of the static operational label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalDynamicAdminLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.3.1.5	Unsigned32	read-only	The beginning of the dynamic administrative label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalDynamicAdminLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.3.1.6	Unsigned32	read-only	The end of the dynamic administrative label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalDynamicOperLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.3.1.7	Unsigned32	read-only	The beginning of the dynamic operational label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalDynamicOperLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.3.1.8	Unsigned32	read-only	The end of the dynamic operational label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalStaticAdminTunnelLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.3.1.9	Unsigned32	read-only	The beginning of the static tunnel administrative label range. There cannot be any overlap between static and dynamic label ranges. Setting this object does not become effective until the device is rebooted.
U32 cienaCesMplsGlobalStaticAdminTunnelLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.3.1.10	Unsigned32	read-only	The end of the static tunnel administrative label range. There cannot be any overlap between static and dynamic label ranges. Setting this object does not become effective until the device is rebooted.
U32 cienaCesMplsGlobalStaticOperTunnelLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.3.1.11	Unsigned32	read-only	The beginning of the static tunnel operational label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalStaticOperTunnelLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.3.1.12	Unsigned32	read-only	The end of the static tunnel operational label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalStaticAdminVcLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.3.1.13	Unsigned32	read-only	The beginning of the static VC administrative label range. There cannot be any overlap between static and dynamic label ranges. Setting this object does not become effective until the device is rebooted.
U32 cienaCesMplsGlobalStaticAdminVcLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.3.1.14	Unsigned32	read-only	The end of the static VC administrative label range. There cannot be any overlap between static and dynamic label ranges. Setting this object does not become effective until the device is rebooted.
U32 cienaCesMplsGlobalStaticOperVcLabelRangeStart	1.3.6.1.4.1.1271.2.1.18.1.3.1.15	Unsigned32	read-only	The beginning of the static VC operational label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalStaticOperVcLabelRangeEnd	1.3.6.1.4.1.1271.2.1.18.1.3.1.16	Unsigned32	read-only	The end of the static VC operational label range. There cannot be any overlap between static and dynamic label ranges.
U32 cienaCesMplsGlobalNextFreeStaticVcLabel	1.3.6.1.4.1.1271.2.1.18.1.3.1.17	Unsigned32	read-only	The next free static VC label. There cannot be any overlap between static and dynamic label ranges.
cienaCesMplsTunnelCosProfileTable	1.3.6.1.4.1.1271.2.1.18.1.3.2		not-accessible	Mpls cos-profile table.
cienaCesMplsTunnelCosProfileEntry	1.3.6.1.4.1.1271.2.1.18.1.3.2.1		not-accessible	Mpls cos-profile table entry.
U32 cienaCesMplsTunnelCosProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.1	Unsigned32	not-accessible	Unique index for Mpls tunnel Cos profile.
STR cienaCesMplsTunnelCosProfileName	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.2	DisplayString	read-only	Mpls tunnel Cos profile name
FCO cienaCesMplsTunnelFrmCosPolicy	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.3	FCosPolicy	read-only	Frame CoS policy of the tunnel.
INT cienaCesMplsTunnelFrmCosMapId	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.4	INTEGER	read-only	The frame CoS map ID of tunnel. This value is valid if the frame CoS policy selected for the tunnel is rcos-mapped.
STR cienaCesMplsTunnelFrmCosMapName	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.5	DisplayString	read-only	Mpls tunnel frame cos Map name
U32 cienaCesMplsTunnelFixedTC	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.6	Unsigned32	read-only	If the frame CoS policy for the tunnel is fixed, this value is used for MPLS encapsulation.
RCO cienaCesMplsTunnelRcosPolicy	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.7	RCosPolicy	read-only	Resolved CoS policy of the tunnel.
STR cienaCesMplsTunnelRcosMapName	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.8	DisplayString	read-only	Mpls tunnel resolved cos Map name. This object is valid only for 39XX and 51XX platforms
INT cienaCesMplsTunnelRCosMapId	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.9	INTEGER	read-only	The resolved CoS map ID of the tunnel. This value is valid if the resolved CoS policy selected for the tunnel is rcos-mapped. This object is valid only for 39XX and 51XX platforms
STR cienaCesMplsTunnelRcosProfileName	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.10	DisplayString	read-only	Mpls Tunnel resolved cos Profile name. This object is valid only for 87XX platforms
U32 cienaCesMplsTunnelRCosProfileId	1.3.6.1.4.1.1271.2.1.18.1.3.2.1.11	Unsigned32	read-only	The resolved Cos profile ID of the Tunnel. This value is valid if the resolved Cos policy selected for the pseudowire is rcos-mapped. This object is valid only for 87XX platforms
cienaCesMplsGlobalTunnelPath	1.3.6.1.4.1.1271.2.1.18.1.3.3
cienaCesMplsGlobalTunnelPathTable	1.3.6.1.4.1.1271.2.1.18.1.3.3.1		not-accessible	The (conceptual) table listing the MPLS tunnel paths. To create an entry in the tunnel path table, cienaCesMplsGlobalTunnelPathName and cienaCesMplsGlobalTunnelPathRowStatus must both be specified.
cienaCesMplsGlobalTunnelPathEntry	1.3.6.1.4.1.1271.2.1.18.1.3.3.1.1		not-accessible	An entry in the tunnel path table.
U32 cienaCesMplsGlobalTunnelPathIndex	1.3.6.1.4.1.1271.2.1.18.1.3.3.1.1.1	Unsigned32	not-accessible	A unique index in the path entry table.
STR cienaCesMplsGlobalTunnelPathName	1.3.6.1.4.1.1271.2.1.18.1.3.3.1.1.2	DisplayString	read-only	Name associated with the path.
C32 cienaCesMplsGlobalTunnelPathUseCount	1.3.6.1.4.1.1271.2.1.18.1.3.3.1.1.3	Counter32	read-only	Indicates the number of encap tunnels that are using this path.
cienaCesMplsGlobalTunnelPathHopTable	1.3.6.1.4.1.1271.2.1.18.1.3.3.2		not-accessible	The (conceptual) table listing the MPLS tunnel path hop. To create an entry in the path-hop table, cienaCesMplsGlobalTunnelPathHopIpAddr and cienaCesMplsGlobalTunnelPathHopRowStatus must both be specified.
cienaCesMplsGlobalTunnelPathHopEntry	1.3.6.1.4.1.1271.2.1.18.1.3.3.2.1		not-accessible	A tunnel hop entry.
U32 cienaCesMplsGlobalTunnelPathHopIndex	1.3.6.1.4.1.1271.2.1.18.1.3.3.2.1.1	Unsigned32	not-accessible	Unique index in the path hop table.
IP cienaCesMplsGlobalTunnelPathHopIpAddr	1.3.6.1.4.1.1271.2.1.18.1.3.3.2.1.2	IpAddress	read-only	IP address associated with this hop. This object cannot be modified once the path hop is created.
INT cienaCesMplsGlobalTunnelPathHopType	1.3.6.1.4.1.1271.2.1.18.1.3.3.2.1.3	INTEGER	read-only	Indidcates the hop type of the path member. This object cannot be modified once the path hop is created.
cienaCesMplsGlobalFreeStaticTunnelLabelTable	1.3.6.1.4.1.1271.2.1.18.1.3.4		not-accessible	Mpls Free static Tunnel Label table.
cienaCesMplsGlobalFreeStaticTunnelLabelEntry	1.3.6.1.4.1.1271.2.1.18.1.3.4.1		not-accessible	Mpls Free static Tunnel Label table.
U32 cienaCesMplsGlobalFreeStaticTunnelLabelIndex	1.3.6.1.4.1.1271.2.1.18.1.3.4.1.1	Unsigned32	not-accessible	Unique index for Mpls Free static Tunnel Label table.
U32 cienaCesMplsGlobalFreeStaticTunnelLabel	1.3.6.1.4.1.1271.2.1.18.1.3.4.1.2	Unsigned32	read-only	Mpls Free static Tunnel Label.
cienaCesMplsPw	1.3.6.1.4.1.1271.2.1.18.1.4
cienaCesMplsPwTable	1.3.6.1.4.1.1271.2.1.18.1.4.1		not-accessible	The (conceptual) table listing the MPLS pseudo wires.
cienaCesMplsPwEntry	1.3.6.1.4.1.1271.2.1.18.1.4.1.1		not-accessible	This represents an entry of the MPLS pseudowire table.
U32 cienaCesMplsPwIndex	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.1	Unsigned32	not-accessible	Unique index in the table.
INT cienaCesMplsPwSignallingType	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.2	INTEGER	read-only	Specifies Pw signalling type
U32 cienaCesMplsPwId	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.3	Unsigned32	read-only	This represents the unique id that is signalled in LDP
STR cienaCesMplsPwName	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.4	DisplayString	read-only	This represents the pseudowire name
STR cienaCesMplsPwCustomerName	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.5	DisplayString	read-only	This represents the customer name
CIE cienaCesMplsPwAdminState	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.6	CienaGlobalState	read-only	This represents the pseudowire administrative status
CIE cienaCesMplsPwOperState	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.7	CienaGlobalState	read-only	This represents the pseudowire operational status
IP cienaCesMplsPwPeerIpAddr	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.8	IpAddress	read-only	Peer Ip address of the pseudowire
I32 cienaCesMplsPwInLabel	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.9	Integer32	read-only	Indicates the inbound label of the pseudowire
I32 cienaCesMplsPwOutLabel	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.10	Integer32	read-only	Indicates the outbound label of the pseudowire
INT cienaCesMplsPwStatusTlv	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.11	INTEGER	read-only	This represents whether the pseudowire status tlv is turned on or off
U32 cienaCesMplsPwRefreshStatusIntvl	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.12	Unsigned32	read-only	This represents the refresh interval for status tlv. This is only applicable for static Pseudowire. For dynamic Pseudowire this is displayed as 0.
VCS cienaCesMplsPwLocalFault	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.13	VCStatus	read-only	This represents the pseudowire local fault
VCS cienaCesMplsPwRemoteFault	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.14	VCStatus	read-only	This represents the pseudowire remote fault
U32 cienaCesMplsPwMtu	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.15	Unsigned32	read-only	Indicates the pseudowire mtu
INT cienaCesMplsPwType	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.16	INTEGER	read-only	This represents the pseudowire type raw or tagged
INT cienaCesMplsPwMode	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.17	INTEGER	read-only	This represents the pseudowire mode whether it is mesh, spoke, or a MS-PW segment
CIE cienaCesMplsPwEgressL2PtTransform	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.20	CienaGlobalState	read-only	This represents the pseudowire L2PT transform for classified L2 CFT control frames
STR cienaCesMplsPwLocalCcCv	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.23	DisplayString	read-only	This represents the CC/CV configured on the local pseudowire
STR cienaCesMplsPwRemoteCcCv	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.24	DisplayString	read-only	This represents the CC/CV configured on the remote pseudowire
STR cienaCesMplsPwOperatingCcCv	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.25	DisplayString	read-only	This represents the negotiated/operating CC/CV
INT cienaCesMplsPwBlocking	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.26	INTEGER	read-only	Specifies whether pseudowire is blocking or forwarding
U32 cienaCesMplsPwVifIndex	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.27	Unsigned32	read-only	This represents the Vif/tunnel group that is being used for the pseudowire
STR cienaCesMplsPwConfigTunnelName	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.28	DisplayString	read-only	This represents the configured transport tunnel name for the pseudowire
TUN cienaCesMplsPwConfigTunnelType	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.29	TunnelType	read-only	This represents the configured transport tunnel type for the pseudowire
U32 cienaCesMplsPwConfigTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.30	Unsigned32	read-only	Specifies the configured transport tunnel index in one of the cienaCesMplsTunnel/cienaCesGmplsTunnel tables for the pseudowire
STR cienaCesMplsPwActiveTunnelName	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.31	DisplayString	read-only	This represents the active transport tunnel name for the pseudowire
TUN cienaCesMplsPwActiveTunnelType	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.32	TunnelType	read-only	This represents the active transport tunnel type for the pseudo wire. This would be the same as configured tunnel type
U32 cienaCesMplsPwActiveTunnelIndex	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.33	Unsigned32	read-only	Specifies the active transport tunnel index in one of the cienaCesMplsTunnel/cienaCesGmplsTunnel tables for the pseudowire
INT cienaCesMplsPwRole	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.34	INTEGER	read-only	This represents the pseudowire role whether it is a protecting or primary pseudowire
STR cienaCesMplsPwPrimaryPwName	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.35	DisplayString	read-only	This represents the primary pseudowire name if this is a secondary pseudowire
U32 cienaCesMplsPwPrimaryPwIndex	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.36	Unsigned32	read-only	This represents the primary pseudowire index in cienaCesMplsPw table if this is a secondary pseudowire
U32 cienaCesMplsPwVsIndex	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.37	Unsigned32	read-only	This represents the virtual switch index in the virtual switch MIB table
U32 cienaCesServiceDelimiterVID	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.38	Unsigned32	read-only	This represents the service delimiter VID. This object is valid only for 39XX and 51XX platforms
U32 cienaCesServiceDelimiterTPID	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.39	Unsigned32	read-only	This represents the service delimiter TPID. This object is valid only for 39XX and 51XX platforms
INT cienaCesMplsPwReversion	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.40	INTEGER	read-only	This represents whether the Pseudowire Reversion is turned on or off. With the Reversion turned on, when the Primary Pseudowire has recovered from earlier failure, it will be held down for a period of cienaCesMplsPwRevertTime(sec) before the switchover from the Backup Pseudowire to Primary Pseudowire takes place. With the Reversion turned off, the user must use manual switchover command to perform a switchover back to the Primary Pseudowire
U32 cienaCesMplsPwRevertTime	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.41	Unsigned32	read-only	This represents the Reversion Hold-time(in seconds) on the Primary Pseudowire. When the Primary Pseudowire has recovered from earlier failure, it will be held down for the length of this hold time. Once the time has elapsed, and if the Primary Pseudowire does not encountered any more failure, there will be a switchover from the Backup Pseudowire back to the Primary Pseudowire
INT cienaCesMplsPwProtectionRole	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.42	INTEGER	read-only	This represents the role of the pseudowire in a Protection bundle.
INT cienaCesMplsPwProtectionState	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.43	INTEGER	read-only	This represents the pseudowire protection state. It only applies to those pseudowires in the protection bundle. For stand alone pseudowire this has no meaning and is reflected as n/a in this object
STR cienaCesMplsPwVsName	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.44	DisplayString	read-only	This represents the virtual switch name to which the pseudowire is attached.
INT cienaCesMplsPwStatusQuery	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.45	INTEGER	read-only	This represents whether the pseudowire status query is enabled. With the status query enabled, the pseudowire is able to query the remote status when it comes up and the remote status is unknown.
STR cienaCesMplsMsPwPeerPwName	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.46	DisplayString	read-only	This represents the peer pseudowire name if this is a MS-PW.
U32 cienaCesMplsMsPwPeerPwIndex	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.47	Unsigned32	read-only	This represents the peer pseudowire index if this is a MS-PW.
U32 cienaCesMplsPwIdInRemoteFault	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.48	Unsigned32	read-only	This represents the PW Id in the SP-PE TLV of the remote Status
IP cienaCesMplsLocalIpInRemoteFault	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.49	IpAddress	read-only	Local Ip address in the SP-PE TLV of the remote Status
IP cienaCesMplsRemoteIpInRemoteFault	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.50	IpAddress	read-only	Remote Ip address in the SP-PE TLV of the remote Status
VCS cienaCesMplsPwFaultToNextHop	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.51	VCStatus	read-only	This represents the aggregated MS-PW faults sent to the next hop
U32 cienaCesMplsPwIdInFaultToNextHop	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.52	Unsigned32	read-only	This represents the PW Id in the SP-PE TLV sent to the next hop
IP cienaCesMplsLocalIpInFaultToNextHop	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.53	IpAddress	read-only	Local Ip address in the SP-PE TLV sent to the next hop
IP cienaCesMplsRemoteIpInFaultToNextHop	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.54	IpAddress	read-only	Remote Ip address in the SP-PE TLV sent to the next hop
MPL cienaCesMplsPwConfigBandwidth	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.55	MplsBitRate	read-only	This represents the configured Bandwidth(in kbps) of pseudowire
MPL cienaCesMplsPwOperBandwidth	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.56	MplsBitRate	read-only	This represents the operational Bandwidth(in kbps) of pseudowire
INT cienaCesMplsPwBandwidthState	1.3.6.1.4.1.1271.2.1.18.1.4.1.1.57	INTEGER	read-only	This represents the Bandwidth state of pseudowire
cienaCesMplsPwCosProfileTable	1.3.6.1.4.1.1271.2.1.18.1.4.2		not-accessible	The (conceptual) table listing the MPLS pseudowire cos profiles.
cienaCesMplsPwCosProfileEntry	1.3.6.1.4.1.1271.2.1.18.1.4.2.1		not-accessible	This represents an entry of the MPLS pseudowire Cos profile table.
U32 cienaCesMplsPwCoSProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.1	Unsigned32	not-accessible	Unique index for Mpls Pw Cos profile.
STR cienaCesMplsPwCoSProfileName	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.2	DisplayString	read-only	Mpls pseudowire Cos profile name
FCO cienaCesMplsPwCosProfileFrmCosPolicy	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.3	FCosPolicy	read-only	Frame CoS policy of the pseudowire
U32 cienaCesMplsPwCosProfileFrmCosMapId	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.4	Unsigned32	read-only	The frame CoS map ID of pseudo wire. This value is valid if the frame Cos policy selected for the pseudowire is rcos-mapped
STR cienaCesMplsPwCosProfileFrmCosMapName	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.5	DisplayString	read-only	Mpls pseudowire frame cos Map name
U32 cienaCesMplsPwCosProfileFixedTC	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.6	Unsigned32	read-only	If the frame CoS policy for the pseudowire is fixed, this value is used for MPLS encapsulation.
RCO cienaCesMplsPwCosProfileRcosPolicy	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.7	RCosPolicy	read-only	Resolved CoS policy of the pseudowire
STR cienaCesMplsPwCosProfileRcosMapName	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.8	DisplayString	read-only	Mpls pseudowire resolved cos Map name. This object is valid only for 39XX and 51XX platforms
U32 cienaCesMplsPwCosProfileRCosMapId	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.9	Unsigned32	read-only	The resolved Cos map ID of the pseudo wire. This value is valid if the resolved Cos policy selected for the pseudowire is rcos-mapped. This object is valid only for 39XX and 51XX platforms
STR cienaCesMplsPwCosProfileRcosProfileName	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.10	DisplayString	read-only	Mpls pseudowire resolved cos Profile name. This object is valid only for 87XX
INT cienaCesMplsPwCosProfileRCosProfileId	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.11	INTEGER	read-only	The resolved Cos profile ID of the pseudo wire. This value is valid if the resolved Cos policy selected for the pseudowire is rcos-mapped. This object is valid only for 87XX
U32 cienaCesMplsPwCosProfileRCosFixed	1.3.6.1.4.1.1271.2.1.18.1.4.2.1.12	Unsigned32	read-only	If the resolved CoS policy for the pseudowire is fixed, this value is used
cienaCesMplsPwVccvProfileTable	1.3.6.1.4.1.1271.2.1.18.1.4.3		not-accessible	The (conceptual) table listing the MPLS pseudowire Vccv profiles.
cienaCesMplsPwVccvProfileEntry	1.3.6.1.4.1.1271.2.1.18.1.4.3.1		not-accessible	This represents an entry of the MPLS pseudowire Vccv profile table.
U32 cienaCesMplsPwVccVProfileIndex	1.3.6.1.4.1.1271.2.1.18.1.4.3.1.1	Unsigned32	not-accessible	Unique index for Mpls Pw Vccv profile.
STR cienaCesMplsPwVccVProfileName	1.3.6.1.4.1.1271.2.1.18.1.4.3.1.2	DisplayString	read-only	Mpls pseudowire Vccv profile name
INT cienaCesMplsPwVccvProfileCcTtlExp	1.3.6.1.4.1.1271.2.1.18.1.4.3.1.3	INTEGER	read-only	This represents the pseudowire TTL-expiry VCCV control channel (CC Type-3) operation
INT cienaCesMplsPwVccvProfileCcCienaOob	1.3.6.1.4.1.1271.2.1.18.1.4.3.1.4	INTEGER	read-only	This represents the pseudowire CIENA proprietary out-of-band VCCV control channel (CC Type-4) operation
cienaCesMplsPwNotif	1.3.6.1.4.1.1271.2.1.18.1.4.4
cienaCesMplsPwNotifTable	1.3.6.1.4.1.1271.2.1.18.1.4.4.1		not-accessible	Table of notification objects required for pseudowire notification.
cienaCesMplsPwNotifEntry	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1		not-accessible	An entry (conceptual row) in the cienaCesMplsPwNotifTable. No Get, GetNext or Set is allowed on this table.
U32 cienaCesMplsPwNotifPwIndex	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.1	Unsigned32	accessible-for-notify	Unique pseudowire index in the PW table
U32 cienaCesMplsPwNotifPwId	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.2	Unsigned32	accessible-for-notify	Unique Pseudowire ID used to identify the PW in the signaling. For the static PW this represents the locally configured value.
STR cienaCesMplsPwNotifPwName	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.3	DisplayString	accessible-for-notify	This represents the locally configured PW name.
IP cienaCesMplsPwNotifPwPeerIpAddr	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.4	IpAddress	accessible-for-notify	This represents the IP address of the Peer on the remote end of the PW.
U32 cienaCesMplsPwNotifPriPwId	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.5	Unsigned32	accessible-for-notify	This represents the PW Id of the primary PW.
STR cienaCesMplsPwNotifPriPwName	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.6	DisplayString	accessible-for-notify	This represents the PW name of the primary PW.
IP cienaCesMplsPwNotifPriPwPeerIpAddr	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.7	IpAddress	accessible-for-notify	This represents the IP address of the Peer on the remote end of the primary PW.
U32 cienaCesMplsPwNotifActPwIndex	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.8	Unsigned32	accessible-for-notify	Unique pseudowire index in the PW table
U32 cienaCesMplsPwNotifActPwId	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.9	Unsigned32	accessible-for-notify	This represents the PW Id of the active PW.
STR cienaCesMplsPwNotifActPwName	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.10	DisplayString	accessible-for-notify	This represents the PW name of the active PW.
IP cienaCesMplsPwNotifActPwPeerIpAddr	1.3.6.1.4.1.1271.2.1.18.1.4.4.1.1.11	IpAddress	accessible-for-notify	This represents the IP address of the Peer on the remote end of the active PW.
cienaCesMplsPWTrafficStatsTable	1.3.6.1.4.1.1271.2.1.18.1.4.5		not-accessible	Mpls PW Traffic Statistics table. The attributes in this table are supported only on specific platforms.
cienaCesMplsPWTrafficStatsEntry	1.3.6.1.4.1.1271.2.1.18.1.4.5.1		not-accessible	Mpls PW Traffic Statistics table entry.
U32 cienaCesMplsPWTrafficStatsPWIndex	1.3.6.1.4.1.1271.2.1.18.1.4.5.1.1	Unsigned32	not-accessible	Unique index for Mpls PW Traffic Statistics table.
U32 cienaCesMplsPWTrafficStatsIncomingPackets	1.3.6.1.4.1.1271.2.1.18.1.4.5.1.2	Unsigned32	read-only	The number of incoming packets for the given PW.
U32 cienaCesMplsPWTrafficStatsOutgoingPackets	1.3.6.1.4.1.1271.2.1.18.1.4.5.1.3	Unsigned32	read-only	The number of outgoing packets for the given PW.
U32 cienaCesMplsPWTrafficStatsIncomingBytes	1.3.6.1.4.1.1271.2.1.18.1.4.5.1.4	Unsigned32	read-only	The number of incoming bytes for the given PW.
U32 cienaCesMplsPWTrafficStatsOutgoingBytes	1.3.6.1.4.1.1271.2.1.18.1.4.5.1.5	Unsigned32	read-only	The number of outgoing bytes for the given PW.
cienaCesMplsTe	1.3.6.1.4.1.1271.2.1.18.1.5
cienaCesTeLinkTable	1.3.6.1.4.1.1271.2.1.18.1.5.1		not-accessible	This table captures the TE-link entries along with their respective attributes.
cienaCesTeLinkEntry	1.3.6.1.4.1.1271.2.1.18.1.5.1.1		not-accessible	This represents an entry for the TE-Link interface
U32 cienaCesTeIfIndex	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.1	Unsigned32	not-accessible	This represents the unique index for TE-Interface.
STR cienaCesTeInterfaceName	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.2	DisplayString	read-only	This represents the TE Interface name.
U32 cienaCesTeLinkMetric	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.3	Unsigned32	read-only	Link cost of the TE-Interface.
U32 cienaCesTeResourceColorGroupIndex	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.4	Unsigned32	read-only	Resource Color Group Index this TE-link is associated to.
OCT cienaCesTeResourceColorBitMask	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.5	OCTET STRING	read-only	This represents individual bit for Resource Color which will be set in Resource Color Group.
U32 cienaCesMplsClassProfIndex	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.6	Unsigned32	read-only	Class Profile Index this TE-link is associated to.
TEM cienaCesTeLinkMode	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.7	TEMode	read-only	TE mode of the TE-Interface.
U32 cienaCesTeLinkSrlgCount	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.8	Unsigned32	read-only	This identifies the total number of SRLGs configured on this TE link.
MPL cienaCesTeLinkMaximumBandwidth	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.9	MplsBitRate	read-only	Maximum TE-link Bandwidth(in kbps). This is same as the port bandwidth on which this TE-link is created
MPL cienaCesTeLinkMaximumReservableBandwidth	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.10	MplsBitRate	read-only	Maximum Reservable bandwidth(in kbps) on this TE-link.
MPL cienaCesTeLinkTotalBandwidthPrio0	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.11	MplsBitRate	read-only	Total Priority 0 Bandwidth(in kbps) allocated in this TE-link.
MPL cienaCesTeLinkReservedBandwidthPrio0	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.12	MplsBitRate	read-only	Reserved Priority 0 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkUnReservedBandwidthPrio0	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.13	MplsBitRate	read-only	UnReserved Priority 0 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkTotalBandwidthPrio1	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.14	MplsBitRate	read-only	Total Priority 1 Bandwidth(in kbps) allocated in this TE-link.
MPL cienaCesTeLinkReservedBandwidthPrio1	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.15	MplsBitRate	read-only	Reserved Priority 1 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkUnReservedBandwidthPrio1	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.16	MplsBitRate	read-only	UnReserved Priority 1 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkTotalBandwidthPrio2	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.17	MplsBitRate	read-only	Total Priority 2 Bandwidth(in kbps) allocated in this TE-link.
MPL cienaCesTeLinkReservedBandwidthPrio2	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.18	MplsBitRate	read-only	Reserved Priority 2 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkUnReservedBandwidthPrio2	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.19	MplsBitRate	read-only	UnReserved Priority 2 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkTotalBandwidthPrio3	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.20	MplsBitRate	read-only	Total Priority 3 Bandwidth(in kbps) allocated in this TE-link.
MPL cienaCesTeLinkReservedBandwidthPrio3	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.21	MplsBitRate	read-only	Reserved Priority 3 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkUnReservedBandwidthPrio3	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.22	MplsBitRate	read-only	UnReserved Priority 3 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkTotalBandwidthPrio4	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.23	MplsBitRate	read-only	Total Priority 4 Bandwidth(in kbps) allocated in this TE-link.
MPL cienaCesTeLinkReservedBandwidthPrio4	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.24	MplsBitRate	read-only	Reserved Priority 4 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkUnReservedBandwidthPrio4	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.25	MplsBitRate	read-only	UnReserved Priority 4 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkTotalBandwidthPrio5	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.26	MplsBitRate	read-only	Total Priority 5 Bandwidth(in kbps) allocated in this TE-link.
MPL cienaCesTeLinkReservedBandwidthPrio5	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.27	MplsBitRate	read-only	Reserved Priority 5 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkUnReservedBandwidthPrio5	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.28	MplsBitRate	read-only	UnReserved Priority 5 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkTotalBandwidthPrio6	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.29	MplsBitRate	read-only	Total Priority 6 Bandwidth(in kbps) allocated in this TE-link.
MPL cienaCesTeLinkReservedBandwidthPrio6	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.30	MplsBitRate	read-only	Reserved Priority 6 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkUnReservedBandwidthPrio6	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.31	MplsBitRate	read-only	UnReserved Priority 6 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkTotalBandwidthPrio7	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.32	MplsBitRate	read-only	Total Priority 7 Bandwidth(in kbps) allocated in this TE-link.
MPL cienaCesTeLinkReservedBandwidthPrio7	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.33	MplsBitRate	read-only	Reserved Priority 7 Bandwidth(in kbps) in this TE-link.
MPL cienaCesTeLinkUnReservedBandwidthPrio7	1.3.6.1.4.1.1271.2.1.18.1.5.1.1.34	MplsBitRate	read-only	UnReserved Priority 7 Bandwidth(in kbps) in this TE-link.
cienaCesTeResourceGrpTable	1.3.6.1.4.1.1271.2.1.18.1.5.2		not-accessible	This table captures the Resource Color Group Template entries.
cienaCesTeResGrpEntry	1.3.6.1.4.1.1271.2.1.18.1.5.2.1		not-accessible	An entry in this table exists for each of the Resource color group template.
U32 cienaCesTeResourceColorGrpIndex	1.3.6.1.4.1.1271.2.1.18.1.5.2.1.1	Unsigned32	not-accessible	This represents the unique index for Resource Color Group entry. Index 0 is used to get the colors which are not associated to any color group cienaCesTeResourceColorsTable
STR cienaCesTeResourceGrpName	1.3.6.1.4.1.1271.2.1.18.1.5.2.1.2	DisplayString	read-only	This represents the name of the Resource Color Group.
OCT cienaCesTeResourceColorGroupBitMask	1.3.6.1.4.1.1271.2.1.18.1.5.2.1.3	OCTET STRING	read-only	This represents the bitmask value for colors added to this Resource Color Group.
C32 cienaCesTeResourceColorGroupUseCount	1.3.6.1.4.1.1271.2.1.18.1.5.2.1.4	Counter32	read-only	Indicates the number of Tunnels using this MPLS Resource Color Group.
cienaCesTeResourceColorsTable	1.3.6.1.4.1.1271.2.1.18.1.5.3		not-accessible	This table captures the Resource Colors entries. These colors can be associated to any Resource Color Group
cienaCesTeResColorEntry	1.3.6.1.4.1.1271.2.1.18.1.5.3.1		not-accessible	An entry in this table exists for each of the Resource colors configured along with its associated Resource Group.
U32 cienaCesTeResourceColorIndex	1.3.6.1.4.1.1271.2.1.18.1.5.3.1.1	Unsigned32	not-accessible	This represents the unique index for Resource Color entry.
STR cienaCesTeResourceColorName	1.3.6.1.4.1.1271.2.1.18.1.5.3.1.2	DisplayString	read-only	This represents the name of the Resource Color.
OCT cienaCesTeResourceColorBit	1.3.6.1.4.1.1271.2.1.18.1.5.3.1.3	OCTET STRING	read-only	This represents individual bit for Resource Color which will be set in Resource Color Group's cienaCesTeResourceColorGroupBitMask.
C32 cienaCesTeResourceColorUseCount	1.3.6.1.4.1.1271.2.1.18.1.5.3.1.4	Counter32	read-only	Indicates the number of MPLS Resource Groups using this Resource Color.
cienaCesTeLinkSrlgTable	1.3.6.1.4.1.1271.2.1.18.1.5.4		not-accessible	This table specifies the SRLGs associated with TE links.
cienaCesTeLinkSrlgEntry	1.3.6.1.4.1.1271.2.1.18.1.5.4.1		not-accessible	An entry in this table contains information about an SRLG associated with a TE link. An ifEntry in the ifTable must exist before a teLinkSrlgEntry using the same ifIndex is created. The ifType of ifEntry must be teLink(200). If a TE link entry in the ifTable is destroyed, then so are all of the entries in the teLinkSrlgTable that use the ifIndex of this TE link.
U32 cienaCesTeLinkSrlg	1.3.6.1.4.1.1271.2.1.18.1.5.4.1.1	Unsigned32	not-accessible	This identifies an SRLG supported by the TE link. An SRLG is identified with a 32-bit number that is unique within an IGP domain. Zero is a valid SRLG number.
SRL cienaCesTeLinkSrlgStatus	1.3.6.1.4.1.1271.2.1.18.1.5.4.1.2	SRLGState	read-only	This variable represents the SRLG value status. Currently we support only active(1) indicating SRLG is configured.
cienaCesMplsMIBNotificationPrefix	1.3.6.1.4.1.1271.2.2.17
cienaCesMplsMIBNotifications	1.3.6.1.4.1.1271.2.2.17.0
NTF cienaCesMplsTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.0.1			This notification is sent when the operational state of an encap tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesMplsNotifEncapTunnelIndex, cienaCesMplsNotifEncapTunnelType, cienaCesMplsNotifEncapTunnelName, cienaCesMplsNotifEncapTunnelAdminState, cienaCesMplsNotifEncapTunnelOperState, cienaCesMplsNotifEncapTunnelOamFaulted, cienaCesMplsNotifEncapTunnelFaultNodeId.
NTF cienaCesMplsEncapTunnelGrpActiveEncapTunnelChange	1.3.6.1.4.1.1271.2.2.17.0.2			This notification is sent whenever the active encap tunnel in a tunnel group changes.
NTF cienaCesMplsTransitTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.0.3			This notification is sent when the operational state of a transit tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesMplsNotifTransitTunnelIndex, cienaCesMplsNotifTransitTunnelType, cienaCesMplsNotifTransitTunnelName, cienaCesMplsNotifTransitTunnelAdminState, cienaCesMplsNotifTransitTunnelOperState, cienaCesMplsNotifTransitTunnelOamFaulted.
NTF cienaCesMplsAssociatedTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.0.6			This notification is sent when the operational state of an associated tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesMplsNotifAssociatedTunnelIndex, cienaCesMplsNotifAssociatedTunnelType, cienaCesMplsNotifAssociatedTunnelName, cienaCesMplsNotifAssociatedTunnelAdminState, cienaCesMplsNotifAssociatedTunnelOperState, cienaCesMplsNotifAssociatedTunnelOamFaulted, cienaCesMplsNotifAssociatedTunnelFaultedNodeId.
NTF cienaCesMplsCacInterfaceThresholdTrap	1.3.6.1.4.1.1271.2.2.17.0.7			This notification is sent when LSP bandwith usage exceeds the threshold. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesMplsNotifCasInterfaceIndex, cienaCesMplsNotifCacInterfaceClassType, cienaCesMplsNotifCacInterfaceName, cienaCesMplsNotifCacInterfaceThreshold.
cienaCesGmplsMIBNotifications	1.3.6.1.4.1.1271.2.2.17.1
NTF cienaCesGmplsEncapUnidirTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.1			This notification is sent when the operational state of an encap uni-direction tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifEncapTunnelIndex, cienaCesGmplsNotifEncapTunnelType, cienaCesGmplsNotifEncapTunnelName, cienaCesGmplsNotifEncapTunnelAdminState, cienaCesGmplsNotifEncapTunnelOperState, cienaCesGmplsNotifEncapTunnelOamFaulted, cienaCesGmplsNotifEncapTunnelFaultedNodeId.
NTF cienaCesGmplsEncapCoroutedTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.2			This notification is sent when the operational state of an encap corouted tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifEncapTunnelIndex, cienaCesGmplsNotifEncapTunnelType, cienaCesGmplsNotifEncapTunnelName, cienaCesGmplsNotifEncapTunnelAdminState, cienaCesGmplsNotifEncapTunnelOperState, cienaCesGmplsNotifEncapTunnelOamFaulted, cienaCesGmplsNotifEncapTunnelFaultedNodeId.
NTF cienaCesGmplsDecapCoroutedTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.3			This notification is sent when the operational state of an decap corouted tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifDecapTunnelIndex, cienaCesGmplsNotifDecapTunnelType, cienaCesGmplsNotifDecapTunnelName, cienaCesGmplsNotifDecapTunnelAdminState, cienaCesGmplsNotifDecapTunnelOperState, cienaCesGmplsNotifDecapTunnelOamFaulted, cienaCesGmplsNotifDecapTunnelFaultedNodeId.
NTF cienaCesGmplsTransitUnidirTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.4			This notification is sent when the operational state of a transit uni-direcition tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifTransitTunnelIndex, cienaCesGmplsNotifTransitTunnelType, cienaCesGmplsNotifTransitTunnelName, cienaCesGmplsNotifTransitTunnelAdminState, cienaCesGmplsNotifTransitTunnelOperState, cienaCesGmplsNotifTransitTunnelOamFaulted.
NTF cienaCesGmplsTransitCoroutedTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.5			This notification is sent when the operational state of a transit corouted tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifTransitTunnelIndex, cienaCesGmplsNotifTransitTunnelType, cienaCesGmplsNotifTransitTunnelName, cienaCesGmplsNotifTransitTunnelAdminState, cienaCesGmplsNotifTransitTunnelOperState, cienaCesGmplsNotifTransitTunnelOamFaulted.
NTF cienaCesGmplsEncapUnidirTunnelGrpActiveEncapTunnelChangeTrap	1.3.6.1.4.1.1271.2.2.17.1.6			This notification is sent whenever the active encap tunnel in an encap uni-direction tunnel group changes.
NTF cienaCesGmplsEncapCoroutedTunnelGrpActiveEncapTunnelChangeTrap	1.3.6.1.4.1.1271.2.2.17.1.7			This notification is sent whenever the active encap tunnel in an encap corouted tunnel group changes.
NTF cienaCesGmplsDecapCoroutedTunnelGrpActiveDecapTunnelChangeTrap	1.3.6.1.4.1.1271.2.2.17.1.8			This notification is sent whenever the active decap tunnel in a decap corouted tunnel group changes.
NTF cienaCesGmplsAssociatedTunnelOperStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.9			This notification is sent when the operational state of an encap tunnel changes. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifAssociatedTunnelIndex, cienaCesGmplsNotifAssociatedTunnelType, cienaCesGmplsNotifAssociatedTunnelName, cienaCesGmplsNotifAssociatedTunnelAdminState, cienaCesGmplsNotifAssociatedTunnelOperState, cienaCesGmplsNotifAssociatedTunnelOamFaulted, cienaCesGmplsNotifAssociatedTunnelFaultedNodeId.
NTF cienaCesGmplsEncapCoroutedTunnelAisFaultStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.10			This notification is obsoleted, its functionality is absorbed in the OperState Change notification.
NTF cienaCesGmplsDecapCoroutedTunnelAisFaultStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.11			This notification is obsoleted, its functionality is absorbed in the OperState Change notification.
NTF cienaCesGmplsAssociatedTunnelAisFaultStateChgTrap	1.3.6.1.4.1.1271.2.2.17.1.12			This notification is obsoleted, its functionality is absorbed in the OperState Change notification.
NTF cienaCesGmplsTunnelAisFaultErrorTrap	1.3.6.1.4.1.1271.2.2.17.1.13			This notification is sent when there is a fault sent for a LSP whose label is not associated with any tunnel. This will happen whenever the AIS admin state is disabled for the bidirectional tunnel. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifTunnelDecapLabel, and cienaCesGmplsNotifTunnelErrorMsg
NTF cienaCesGmplsEncapTunnelResizeResultTrap	1.3.6.1.4.1.1271.2.2.17.1.14			This notification is sent when the encap tunnel auto size is done Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifEncapTunnelIndex, cienaCesGmplsNotifEncapTunnelType, cienaCesGmplsNotifEncapTunnelName, cienaCesGmplsNotifEncapTunnelResult, cienaCesGmplsNotifEncapTunnelProtectionRole, cienaCesGmplsNotifEncapTunnelRequestdBw and cienaCesGmplsNotifEncapTunnelOperationalBw.
NTF cienaCesGmplsEncapTunnelMbbResultTrap	1.3.6.1.4.1.1271.2.2.17.1.15			This notification is sent when the encap tunnel MBB done Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesGmplsNotifEncapTunnelIndex, cienaCesGmplsNotifEncapTunnelType, cienaCesGmplsNotifEncapTunnelName, cienaCesGmplsNotifEncapTunnelResult, cienaCesGmplsNotifEncapTunnelProtectionRole, cienaCesGmplsNotifEncapTunnelRequestdBw and cienaCesGmplsNotifEncapTunnelOperationalBw, cienaCesGmplsNotifEncapTunnelMbbParentApp.
cienaCesMplsPwMIBNotifications	1.3.6.1.4.1.1271.2.2.17.2
NTF cienaCesMplsPwDown	1.3.6.1.4.1.1271.2.2.17.2.1			This notification is sent when the operational state of a pseudowire has changed from up to down.
NTF cienaCesMplsPwUp	1.3.6.1.4.1.1271.2.2.17.2.2			This notification is sent when the operational state of a pseudowire has changed from down to up.
NTF cienaCesMplsPwBundleActivePwChange	1.3.6.1.4.1.1271.2.2.17.2.3			This notification is sent when the active member of the pseudowire bundle has changed.

RFC description

Ciena vendor-private MIB for MPLS services management on Ciena CES platforms.

Start monitoring Ciena Carrier Ethernet switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CIENA-CES-MPLS-MIB