HUAWEI-RSVPTE-MIB

All MIBs › HUAWEI-RSVPTE-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2014-10-25

Category: MPLS and Traffic Engineering, Vendor: Huawei

Description: Huawei RSVP-TE (Resource Reservation Protocol Traffic Engineering) MIB for managing TE tunnels, LSP reservations, and constraints.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-RSVPTE-MIB?

HUAWEI-RSVPTE-MIB is a Huawei MPLS MIB implementing management objects for RSVP-TE (Resource Reservation Protocol - Traffic Engineering), described simply as covering the RSVP Protocol, used to signal and maintain MPLS traffic-engineered (TE) tunnels and their bandwidth/LSP reservations. It exposes configuration and state data for TE tunnels, associated LSPs, and the resource reservation constraints (bandwidth, priority) negotiated along each tunnel's path. For monitoring, it provides visibility into the software/protocol-level health of MPLS-TE tunnels, tracking whether a tunnel's RSVP-TE session is established, whether reserved bandwidth matches the configured constraint, and whether reservation failures or path re-optimizations have occurred, which are key indicators of traffic-engineering health distinct from raw interface hardware status. It is a Huawei implementation aligned with the IETF RSVP-TE standard (RFC 3209) and the broader MPLS-TE MIB framework. It is deployed on Huawei MPLS-capable routers in service-provider and enterprise WAN backbones that use traffic engineering to guarantee bandwidth and path selection for critical traffic. Engineers can download the HUAWEI-RSVPTE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-RSVPTE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei MPLS routers

Monitoring Examples

No sample objects were provided, but a typical scenario would be polling RSVP-TE tunnel/LSP state objects to confirm a TE tunnel remains signaled and its reserved bandwidth constraint is intact, catching a tunnel that failed to re-signal after a path failure and dropped to a lower-bandwidth backup path or went down entirely.

What Can Be Monitored

RSVP-TE tunnel/LSP state
reserved bandwidth
reservation/signaling failures
path re-optimization events

Imported Objects

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From INTEGRATED-SERVICES-MIB

BitRate
BurstSize
MessageSize
QosService
SessionType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus
TimeInterval
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using hwRsvpTeSessionSenders OID:

Select a Huawei MPLS router (RSVP-TE traffic-engineered tunnels) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hwRsvpTeSessionSenders into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of distinct senders currently known to be part of this session. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwRsvpTe	1.3.6.1.4.1.2011.5.25.148			The MIB module to describe the RSVP Protocol
hwRsvpTeObjects	1.3.6.1.4.1.2011.5.25.148.1
hwRsvpTeSessionTable	1.3.6.1.4.1.2011.5.25.148.1.1		not-accessible	A table of all sessions seen by a given sys- tem.
hwRsvpTeSessionEntry	1.3.6.1.4.1.2011.5.25.148.1.1.1		not-accessible	A single session seen by a given system.
G32 hwRsvpTeSessionNumber	1.3.6.1.4.1.2011.5.25.148.1.1.1.1	Gauge32	not-accessible	The number of this session. This is for SNMP Indexing purposes only and has no relation to any protocol value.
SES hwRsvpTeSessionType	1.3.6.1.4.1.2011.5.25.148.1.1.1.2	SessionType	read-only	The type of session (IP4, IP6, IP6 with flow information, etc).
OCT hwRsvpTeSessionDestAddr	1.3.6.1.4.1.2011.5.25.148.1.1.1.3	OCTET STRING	read-only	The destination address used by all senders in this session.
I32 hwRsvpTeSessionDestAddrLength	1.3.6.1.4.1.2011.5.25.148.1.1.1.4	Integer32	read-only	The CIDR prefix length of the session address, which is 32 for IP4 host and multicast ad- dresses, and 128 for IP6 addresses.
G32 hwRsvpTeSessionSendersEx	1.3.6.1.4.1.2011.5.25.148.1.1.1.5	Gauge32	read-only	The number of distinct senders currently known to be part of this session.
G32 hwRsvpTeSessionReceivers	1.3.6.1.4.1.2011.5.25.148.1.1.1.6	Gauge32	read-only	The number of reservations being requested of this system for this session.
G32 hwRsvpTeSessionRequests	1.3.6.1.4.1.2011.5.25.148.1.1.1.7	Gauge32	read-only	The number of reservation requests this system is sending upstream for this session.
I32 hwRsvpTeSessionTunnelId	1.3.6.1.4.1.2011.5.25.148.1.1.1.8	Integer32	read-only	A 16-bit identifier used in the SESSION that remains constant over the life of the tunnel.
IP hwRsvpTeSessionTunnelExtId	1.3.6.1.4.1.2011.5.25.148.1.1.1.9	IpAddress	read-only	An identifier used in the SESSION that remains constant over the life of the tunnel. Normally the identifier is set to all zeros. Ingress nodes that wish to narrow the scope of a SESSION to the ingress-egress pair may place their IPv4 address here as a globally unique identifier.
G32 hwRsvpTeSessionLspsNumber	1.3.6.1.4.1.2011.5.25.148.1.1.1.10	Gauge32	read-only	The number of LSPs that belong to this session.
INT hwRsvpTeSessionStyle	1.3.6.1.4.1.2011.5.25.148.1.1.1.11	INTEGER	read-only	An enumerable value to identify the treatment of reservations for different senders within the same session: WF 10001b, FF01010b, SE 10010b.
hwRsvpTeSenderTable	1.3.6.1.4.1.2011.5.25.148.1.2		not-accessible	Information describing the state information displayed by senders in PATH messages.
hwRsvpTeSenderEntry	1.3.6.1.4.1.2011.5.25.148.1.2.1		not-accessible	Information describing the state information displayed by a single sender's PATH message.
G32 hwRsvpTeSenderNumber	1.3.6.1.4.1.2011.5.25.148.1.2.1.1	Gauge32	not-accessible	The number of this sender. This is for SNMP Indexing purposes only and has no relation to any protocol value.
SES hwRsvpTeSenderType	1.3.6.1.4.1.2011.5.25.148.1.2.1.2	SessionType	read-only	The type of session (IP4, IP6, IP6 with flow information, etc).
OCT hwRsvpTeSenderDestAddr	1.3.6.1.4.1.2011.5.25.148.1.2.1.3	OCTET STRING	read-only	The destination address used by all senders in this session.
OCT hwRsvpTeSenderAddr	1.3.6.1.4.1.2011.5.25.148.1.2.1.4	OCTET STRING	read-only	The source address used by this sender in this session.
I32 hwRsvpTeSenderDestAddrLength	1.3.6.1.4.1.2011.5.25.148.1.2.1.5	Integer32	read-only	The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.
I32 hwRsvpTeSenderAddrLength	1.3.6.1.4.1.2011.5.25.148.1.2.1.6	Integer32	read-only	The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.
OCT hwRsvpTeSenderHopAddr	1.3.6.1.4.1.2011.5.25.148.1.2.1.7	OCTET STRING	read-only	The address used by the previous RSVP hop (which may be the original sender).
I32 hwRsvpTeSenderHopLih	1.3.6.1.4.1.2011.5.25.148.1.2.1.8	Integer32	read-only	The Logical Interface Handle used by the pre- vious RSVP hop (which may be the original sender).
I32 hwRsvpTeSenderInterface	1.3.6.1.4.1.2011.5.25.148.1.2.1.9	Integer32	read-only	The ifIndex value of the interface on which this PATH message was most recently received.
BIT hwRsvpTeSenderTSpecRate	1.3.6.1.4.1.2011.5.25.148.1.2.1.10	BitRate	read-only	The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeSenderTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed hwRsvpTeSen- derTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.
BIT hwRsvpTeSenderTSpecPeakRate	1.3.6.1.4.1.2011.5.25.148.1.2.1.11	BitRate	read-only	The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.
BUR hwRsvpTeSenderTSpecBurst	1.3.6.1.4.1.2011.5.25.148.1.2.1.12	BurstSize	read-only	The size of the largest burst expected from the sender at a time.
MES hwRsvpTeSenderTSpecMinTu	1.3.6.1.4.1.2011.5.25.148.1.2.1.13	MessageSize	read-only	The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.
MES hwRsvpTeSenderTSpecMaxTu	1.3.6.1.4.1.2011.5.25.148.1.2.1.14	MessageSize	read-only	The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.
I32 hwRsvpTeSenderInterval	1.3.6.1.4.1.2011.5.25.148.1.2.1.15	Integer32	read-only	The interval between refresh messages as ad- vertised by the previous hop.
T/F hwRsvpTeSenderRsvpHop	1.3.6.1.4.1.2011.5.25.148.1.2.1.16	TruthValue	read-only	If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop.
OCT hwRsvpTeSenderPolicy	1.3.6.1.4.1.2011.5.25.148.1.2.1.17	OCTET STRING	read-only	The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
T/F hwRsvpTeSenderAdspecBreak	1.3.6.1.4.1.2011.5.25.148.1.2.1.18	TruthValue	read-only	The global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in the path. If FALSE, no non-IS hops were detected.
I32 hwRsvpTeSenderAdspecHopCount	1.3.6.1.4.1.2011.5.25.148.1.2.1.19	Integer32	read-only	The hop count general characterization parame- ter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present
BIT hwRsvpTeSenderAdspecPathBw	1.3.6.1.4.1.2011.5.25.148.1.2.1.20	BitRate	read-only	The path bandwidth estimate general character- ization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present
I32 hwRsvpTeSenderAdspecMinLatency	1.3.6.1.4.1.2011.5.25.148.1.2.1.21	Integer32	read-only	The minimum path latency general characteriza- tion parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present
I32 hwRsvpTeSenderAdspecMtu	1.3.6.1.4.1.2011.5.25.148.1.2.1.22	Integer32	read-only	The composed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present
T/F hwRsvpTeSenderAdspecGuaranteedSvc	1.3.6.1.4.1.2011.5.25.148.1.2.1.23	TruthValue	read-only	If TRUE, the ADSPEC contains a Guaranteed Ser- vice fragment. If FALSE, the ADSPEC does not contain a Guaranteed Service fragment.
T/F hwRsvpTeSenderAdspecGuaranteedBreak	1.3.6.1.4.1.2011.5.25.148.1.2.1.24	TruthValue	read-only	If TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the guaranteed service. If FALSE, and hwRsvpTe- SenderAdspecGuaranteedSvc is TRUE, the 'break' bit is not set. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns FALSE or noSuchValue.
I32 hwRsvpTeSenderAdspecGuaranteedCtot	1.3.6.1.4.1.2011.5.25.148.1.2.1.25	Integer32	read-only	If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderAdspecGuaranteedDtot	1.3.6.1.4.1.2011.5.25.148.1.2.1.26	Integer32	read-only	If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderAdspecGuaranteedCsum	1.3.6.1.4.1.2011.5.25.148.1.2.1.27	Integer32	read-only	If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'C' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderAdspecGuaranteedDsum	1.3.6.1.4.1.2011.5.25.148.1.2.1.28	Integer32	read-only	If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'D' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderAdspecGuaranteedHopCount	1.3.6.1.4.1.2011.5.25.148.1.2.1.29	Integer32	read-only	If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.
BIT hwRsvpTeSenderAdspecGuaranteedPathBw	1.3.6.1.4.1.2011.5.25.148.1.2.1.30	BitRate	read-only	If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderAdspecGuaranteedMinLatency	1.3.6.1.4.1.2011.5.25.148.1.2.1.31	Integer32	read-only	If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderAdspecGuaranteedMtu	1.3.6.1.4.1.2011.5.25.148.1.2.1.32	Integer32	read-only	If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.
T/F hwRsvpTeSenderAdspecCtrlLoadSvc	1.3.6.1.4.1.2011.5.25.148.1.2.1.33	TruthValue	read-only	If TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load Service frag- ment.
T/F hwRsvpTeSenderAdspecCtrlLoadBreak	1.3.6.1.4.1.2011.5.25.148.1.2.1.34	TruthValue	read-only	If TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the controlled load service. If FALSE, and hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, the 'break' bit is not set. If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns FALSE or noSuchValue.
I32 hwRsvpTeSenderAdspecCtrlLoadHopCount	1.3.6.1.4.1.2011.5.25.148.1.2.1.35	Integer32	read-only	If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.
BIT hwRsvpTeSenderAdspecCtrlLoadPathBw	1.3.6.1.4.1.2011.5.25.148.1.2.1.36	BitRate	read-only	If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderAdspecCtrlLoadMinLatency	1.3.6.1.4.1.2011.5.25.148.1.2.1.37	Integer32	read-only	If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderAdspecCtrlLoadMtu	1.3.6.1.4.1.2011.5.25.148.1.2.1.38	Integer32	read-only	If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.
I32 hwRsvpTeSenderTtl	1.3.6.1.4.1.2011.5.25.148.1.2.1.39	Integer32	read-only	The TTL value in the RSVP header that was last received.
I32 hwRsvpTeLspId	1.3.6.1.4.1.2011.5.25.148.1.2.1.40	Integer32	read-only	A 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself.
I32 hwRsvpTeSenderMsgIdSndFlag	1.3.6.1.4.1.2011.5.25.148.1.2.1.41	Integer32	read-only	Indicates that the message sender requests the peer to send an acknowledgment for the message. (0x01: ACK desired.)
G32 hwRsvpTeSenderMsgIdSndEpoch	1.3.6.1.4.1.2011.5.25.148.1.2.1.42	Gauge32	read-only	A value that indicates when the Message_Identi- fier sequence has been reset.
G32 hwRsvpTeSenderMsgIdSndNumber	1.3.6.1.4.1.2011.5.25.148.1.2.1.43	Gauge32	read-only	When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the Epoch changes or when the value wraps. A return of 0 indicates the absence of the MESSAGE_ID object to be sent.
I32 hwRsvpTeSenderMsgIdRcvFlag	1.3.6.1.4.1.2011.5.25.148.1.2.1.44	Integer32	read-only	The message ID flag of the message latest received. It is used to identify whether ACK is desired or not. And it can be extended. (0x01: ACK desired.)
G32 hwRsvpTeSenderMsgIdRcvEpoch	1.3.6.1.4.1.2011.5.25.148.1.2.1.45	Gauge32	read-only	The message ID epoch of the message latest received form the interface.
G32 hwRsvpTeSenderMsgIdRcvNumber	1.3.6.1.4.1.2011.5.25.148.1.2.1.46	Gauge32	read-only	The message ID number of the message latest received form the interface. A return of 0 indicates the absence of the MESSAGE_ID object received.
I32 hwRsvpTeSenderClassType	1.3.6.1.4.1.2011.5.25.148.1.2.1.47	Integer32	read-only	Indicates the class-type. A return of zero indicates the absence of the object.
INT hwRsvpTeSenderLabelRequestCtype	1.3.6.1.4.1.2011.5.25.148.1.2.1.48	INTEGER	read-only	The type of label request (without label range, with ATM label range, with frame relay label range, etc).
I32 hwRsvpTeSenderLabelRequestL3pid	1.3.6.1.4.1.2011.5.25.148.1.2.1.49	Integer32	read-only	An identifier of the layer 3 protocol using this path. Standard Ethertype values are used.
I32 hwRsvpTeSenderLabelRequestAtmMinVpi	1.3.6.1.4.1.2011.5.25.148.1.2.1.50	Integer32	read-only	This 12 bit field specifies the lower bound of a block of Virtual Path Identifiers that is supported on the originating switch. If the VPI is less than 12-bits it must be right justified in this field and preceding bits must be set to zero.
I32 hwRsvpTeSenderLabelRequestAtmMinVci	1.3.6.1.4.1.2011.5.25.148.1.2.1.51	Integer32	read-only	This 16 bit field specifies the lower bound of a block of Virtual Connection Identifiers that is supported on the originating switch. If the VCI is less than 16-bits it must be right justified in this field and preceding bits must be set to zero.
I32 hwRsvpTeSenderLabelRequestAtmMaxVpi	1.3.6.1.4.1.2011.5.25.148.1.2.1.52	Integer32	read-only	This 12 bit field specifies the upper bound of a block of Virtual Path Identifiers that is supported on the originating switch. If the VPI is less than 12-bits it must be right justified in this field and preceding bits must be set to zero.
I32 hwRsvpTeSenderLabelRequestAtmMaxVci	1.3.6.1.4.1.2011.5.25.148.1.2.1.53	Integer32	read-only	This 16 bit field specifies the upper bound of a block of Virtual Connection Identifiers that is supported on the originating switch. If the VCI is less than 16-bits it must be right justified in this field and preceding bits must be set to zero.
I32 hwRsvpTeSenderLabelRequestFrMinDlci	1.3.6.1.4.1.2011.5.25.148.1.2.1.54	Integer32	read-only	This 23-bit field specifies the lower bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch. The DLCI must be right justified in this field and unused bits must be set to 0.
I32 hwRsvpTeSenderLabelRequestFrMaxDlci	1.3.6.1.4.1.2011.5.25.148.1.2.1.55	Integer32	read-only	This 23-bit field specifies the upper bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch. The DLCI must be right justified in this field and unused bits must be set to 0.
INT hwRsvpTeSenderSessionAttrType	1.3.6.1.4.1.2011.5.25.148.1.2.1.56	INTEGER	read-only	The type of the session_attribute (without resource affinities or with resource affinities).
I32 hwRsvpTeSenderSessionAttrSetupPrio	1.3.6.1.4.1.2011.5.25.148.1.2.1.57	Integer32	read-only	The priority of the session with respect to taking resources, in the range of 0 to 7. The value 0 is the highest priority. The Setup Priority is used in deciding whether this session can preempt another session. The default value is 7.
I32 hwRsvpTeSenderSessionAttrHoldPrio	1.3.6.1.4.1.2011.5.25.148.1.2.1.58	Integer32	read-only	The priority of the session with respect to holding resources, in the range of 0 to 7. The value 0 is the highest priority. Holding Priority is used in deciding whether this session can be preempted by another session. The default value is 7.
I32 hwRsvpTeSenderSessionAttrFlag	1.3.6.1.4.1.2011.5.25.148.1.2.1.59	Integer32	read-only	A mixed value. (0x01: Local protection desired; 0x02: Label recording desired; 0x04: SE Style desired; 0x08: bandwidth protection desired; 0x10: node protection desired; 0x20: Path re-evaluation request; 0x40: Soft preemption desired)
OCT hwRsvpTeSenderSessionAttrName	1.3.6.1.4.1.2011.5.25.148.1.2.1.60	OCTET STRING	read-only	Session name, a null padded string of characters.
G32 hwRsvpTeSenderSessionAttrExcludeAny	1.3.6.1.4.1.2011.5.25.148.1.2.1.61	Gauge32	read-only	A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link unacceptable.
G32 hwRsvpTeSenderSessionAttrIncludeAny	1.3.6.1.4.1.2011.5.25.148.1.2.1.62	Gauge32	read-only	A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link acceptable (with respect to this test). A null set (all bits set to zero) automatically passes.
G32 hwRsvpTeSenderSessionAttrIncludeAll	1.3.6.1.4.1.2011.5.25.148.1.2.1.63	Gauge32	read-only	A 32-bit vector representing a set of attribute filters associated with a tunnel all of which must be present for a link to be acceptable (with respect to this test). A null set (all bits set to zero) automatically passes.
I32 hwRsvpTeSenderFrrSetupPrio	1.3.6.1.4.1.2011.5.25.148.1.2.1.64	Integer32	read-only	The priority of the backup path with respect to taking resources, in the range 0 to 7. The value 0 is the highest priority. Setup Priority is used in deciding whether this session can preempt another session. See [RSVP-TE] for the usage on priority. The default value is 7.
I32 hwRsvpTeSenderFrrHoldPrio	1.3.6.1.4.1.2011.5.25.148.1.2.1.65	Integer32	read-only	The priority of the backup path with respect to holding resources, in the range 0 to 7. The value 0 is the highest priority. Holding Priority is used in deciding whether this session can be preempted by another session. The default value is 7.
I32 hwRsvpTeSenderFrrHopLimit	1.3.6.1.4.1.2011.5.25.148.1.2.1.66	Integer32	read-only	The maximum number of extra hops the backup path is allowed to take, from current node (a PLR) to an MP, with PLR and MP excluded from the count. For example, hop-limit of 0 means that only direct links between PLR and MP can be considered. The default value is 16.
INT hwRsvpTeSenderFrrFlag	1.3.6.1.4.1.2011.5.25.148.1.2.1.67	INTEGER	read-only	An enumerable value to indicate the protection schema desired (0x01, One-to-One Backup Desired; 0x02, Facility Backup Desired; 0x03, No Backup Desired).
BIT hwRsvpTeSenderFrrBandwidth	1.3.6.1.4.1.2011.5.25.148.1.2.1.68	BitRate	read-only	Bandwidth estimate; 32-bit IEEE floating point integer, in bits per second.
G32 hwRsvpTeSenderFrrExcludeAny	1.3.6.1.4.1.2011.5.25.148.1.2.1.69	Gauge32	read-only	A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link unacceptable.
G32 hwRsvpTeSenderFrrIncludeAny	1.3.6.1.4.1.2011.5.25.148.1.2.1.70	Gauge32	read-only	A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link acceptable (with respect to this test). A null set (all bits set to zero) automatically passes.
G32 hwRsvpTeSenderFrrIncludeAll	1.3.6.1.4.1.2011.5.25.148.1.2.1.71	Gauge32	read-only	A 32-bit vector representing a set of attribute filters associated with a backup path, all of which must be present for a link to be acceptable (with respect to this test). A null set (all bits set to zero) automatically passes.
INT hwRsvpTeSenderFrrInuseFlag	1.3.6.1.4.1.2011.5.25.148.1.2.1.72	INTEGER	read-only	An enumerable value to indicate the fast-reroute state of this sender (normal, PLR in use, MP in use, PLR in use and MP in use, under protection).
I32 hwRsvpTeSenderDiffServPsc	1.3.6.1.4.1.2011.5.25.148.1.2.1.73	Integer32	read-only	This 16 bits field indicates a PHB Scheduling Class to be supported by the LSP.
hwRsvpTeResvTable	1.3.6.1.4.1.2011.5.25.148.1.3		not-accessible	Information describing the state information displayed by receivers in RESV messages.
hwRsvpTeResvEntry	1.3.6.1.4.1.2011.5.25.148.1.3.1		not-accessible	Information describing the state information displayed by a single receiver's RESV message concerning a single sender.
G32 hwRsvpTeResvNumber	1.3.6.1.4.1.2011.5.25.148.1.3.1.1	Gauge32	not-accessible	The number of this reservation request. This is for SNMP Indexing purposes only and has no relation to any protocol value.
SES hwRsvpTeResvType	1.3.6.1.4.1.2011.5.25.148.1.3.1.2	SessionType	read-only	The type of session (IP4, IP6, IP6 with flow information, etc).
OCT hwRsvpTeResvDestAddr	1.3.6.1.4.1.2011.5.25.148.1.3.1.3	OCTET STRING	read-only	The destination address used by all senders in this session.
OCT hwRsvpTeResvSenderAddr	1.3.6.1.4.1.2011.5.25.148.1.3.1.4	OCTET STRING	read-only	The source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'.
I32 hwRsvpTeResvDestAddrLength	1.3.6.1.4.1.2011.5.25.148.1.3.1.5	Integer32	read-only	The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.
I32 hwRsvpTeResvSenderAddrLength	1.3.6.1.4.1.2011.5.25.148.1.3.1.6	Integer32	read-only	The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.
OCT hwRsvpTeResvHopAddr	1.3.6.1.4.1.2011.5.25.148.1.3.1.7	OCTET STRING	read-only	The address used by the next RSVP hop (which may be the ultimate receiver).
I32 hwRsvpTeResvHopLih	1.3.6.1.4.1.2011.5.25.148.1.3.1.8	Integer32	read-only	The Logical Interface Handle received from the previous RSVP hop (which may be the ultimate receiver).
I32 hwRsvpTeResvInterface	1.3.6.1.4.1.2011.5.25.148.1.3.1.9	Integer32	read-only	The ifIndex value of the interface on which this RESV message was most recently received.
QOS hwRsvpTeResvService	1.3.6.1.4.1.2011.5.25.148.1.3.1.10	QosService	read-only	The QoS Service classification requested by the receiver.
BIT hwRsvpTeResvTSpecRate	1.3.6.1.4.1.2011.5.25.148.1.3.1.11	BitRate	read-only	The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeResvTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed hwRsvpTeResvTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.
BIT hwRsvpTeResvTSpecPeakRate	1.3.6.1.4.1.2011.5.25.148.1.3.1.12	BitRate	read-only	The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.
BUR hwRsvpTeResvTSpecBurst	1.3.6.1.4.1.2011.5.25.148.1.3.1.13	BurstSize	read-only	The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option.
MES hwRsvpTeResvTSpecMinTu	1.3.6.1.4.1.2011.5.25.148.1.3.1.14	MessageSize	read-only	The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.
MES hwRsvpTeResvTSpecMaxTu	1.3.6.1.4.1.2011.5.25.148.1.3.1.15	MessageSize	read-only	The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.
BIT hwRsvpTeResvRSpecRate	1.3.6.1.4.1.2011.5.25.148.1.3.1.16	BitRate	read-only	If the requested service is guaranteed, as specified by hwRsvpTeResvService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue.
I32 hwRsvpTeResvRSpecSlack	1.3.6.1.4.1.2011.5.25.148.1.3.1.17	Integer32	read-only	If the requested service is guaranteed, as specified by hwRsvpTeResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.
I32 hwRsvpTeResvInterval	1.3.6.1.4.1.2011.5.25.148.1.3.1.18	Integer32	read-only	The interval between refresh messages as ad- vertised by the Next Hop.
OCT hwRsvpTeResvScope	1.3.6.1.4.1.2011.5.25.148.1.3.1.19	OCTET STRING	read-only	The contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. If the length is non-zero, this contains a series of IP4 or IP6 addresses.
T/F hwRsvpTeResvShared	1.3.6.1.4.1.2011.5.25.148.1.3.1.20	TruthValue	read-only	If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.
T/F hwRsvpTeResvExplicit	1.3.6.1.4.1.2011.5.25.148.1.3.1.21	TruthValue	read-only	If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.
T/F hwRsvpTeResvRsvpHop	1.3.6.1.4.1.2011.5.25.148.1.3.1.22	TruthValue	read-only	If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop.
OCT hwRsvpTeResvPolicy	1.3.6.1.4.1.2011.5.25.148.1.3.1.23	OCTET STRING	read-only	The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
I32 hwRsvpTeResvTtl	1.3.6.1.4.1.2011.5.25.148.1.3.1.24	Integer32	read-only	The TTL value in the RSVP header that was last received.
OCT hwRsvpTeResvConfirm	1.3.6.1.4.1.2011.5.25.148.1.3.1.25	OCTET STRING	read-only	Receiver's address.
hwRsvpTeResvFwdTable	1.3.6.1.4.1.2011.5.25.148.1.4		not-accessible	Information describing the state information displayed upstream in RESV messages.
hwRsvpTeResvFwdEntry	1.3.6.1.4.1.2011.5.25.148.1.4.1		not-accessible	Information describing the state information displayed upstream in an RESV message concern- ing a single sender.
G32 hwRsvpTeResvFwdNumber	1.3.6.1.4.1.2011.5.25.148.1.4.1.1	Gauge32	not-accessible	The number of this reservation request. This is for SNMP Indexing purposes only and has no relation to any protocol value.
SES hwRsvpTeResvFwdType	1.3.6.1.4.1.2011.5.25.148.1.4.1.2	SessionType	read-only	The type of session (IP4, IP6, IP6 with flow information, etc).
OCT hwRsvpTeResvFwdDestAddr	1.3.6.1.4.1.2011.5.25.148.1.4.1.3	OCTET STRING	read-only	The destination address used by all senders in this session.
OCT hwRsvpTeResvFwdSenderAddr	1.3.6.1.4.1.2011.5.25.148.1.4.1.4	OCTET STRING	read-only	The source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'.
I32 hwRsvpTeResvFwdDestAddrLength	1.3.6.1.4.1.2011.5.25.148.1.4.1.5	Integer32	read-only	The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.
I32 hwRsvpTeResvFwdSenderAddrLength	1.3.6.1.4.1.2011.5.25.148.1.4.1.6	Integer32	read-only	The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.
OCT hwRsvpTeResvFwdHopAddr	1.3.6.1.4.1.2011.5.25.148.1.4.1.7	OCTET STRING	read-only	The address of the (previous) RSVP that will receive this message.
I32 hwRsvpTeResvFwdHopLih	1.3.6.1.4.1.2011.5.25.148.1.4.1.8	Integer32	read-only	The Logical Interface Handle sent to the (pre- vious) RSVP that will receive this message.
I32 hwRsvpTeResvFwdInterface	1.3.6.1.4.1.2011.5.25.148.1.4.1.9	Integer32	read-only	The ifIndex value of the interface on which this RESV message was most recently sent.
QOS hwRsvpTeResvFwdService	1.3.6.1.4.1.2011.5.25.148.1.4.1.10	QosService	read-only	The QoS Service classification requested.
BIT hwRsvpTeResvFwdTSpecRate	1.3.6.1.4.1.2011.5.25.148.1.4.1.11	BitRate	read-only	The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeResvFwdT- SpecPeakRate (if supported by the service model);however, averaged across two or more burst intervals, the rate should not exceed hwRsvpTeResvFwdTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.
BIT hwRsvpTeResvFwdTSpecPeakRate	1.3.6.1.4.1.2011.5.25.148.1.4.1.12	BitRate	read-only	The Peak Bit Rate of the sender's data stream Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.
BUR hwRsvpTeResvFwdTSpecBurst	1.3.6.1.4.1.2011.5.25.148.1.4.1.13	BurstSize	read-only	The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option.
MES hwRsvpTeResvFwdTSpecMinTu	1.3.6.1.4.1.2011.5.25.148.1.4.1.14	MessageSize	read-only	The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.
MES hwRsvpTeResvFwdTSpecMaxTu	1.3.6.1.4.1.2011.5.25.148.1.4.1.15	MessageSize	read-only	The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.
BIT hwRsvpTeResvFwdRSpecRate	1.3.6.1.4.1.2011.5.25.148.1.4.1.16	BitRate	read-only	If the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue.
I32 hwRsvpTeResvFwdRSpecSlack	1.3.6.1.4.1.2011.5.25.148.1.4.1.17	Integer32	read-only	If the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.
I32 hwRsvpTeResvFwdInterval	1.3.6.1.4.1.2011.5.25.148.1.4.1.18	Integer32	read-only	The interval between refresh messages adver- tised to the Previous Hop.
OCT hwRsvpTeResvFwdScope	1.3.6.1.4.1.2011.5.25.148.1.4.1.19	OCTET STRING	read-only	The contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
T/F hwRsvpTeResvFwdShared	1.3.6.1.4.1.2011.5.25.148.1.4.1.20	TruthValue	read-only	If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.
T/F hwRsvpTeResvFwdExplicit	1.3.6.1.4.1.2011.5.25.148.1.4.1.21	TruthValue	read-only	If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.
T/F hwRsvpTeResvFwdRsvpHop	1.3.6.1.4.1.2011.5.25.148.1.4.1.22	TruthValue	read-only	If TRUE, the node believes that the next IP hop is an RSVP hop. If FALSE, the node be- lieves that the next IP hop may not be an RSVP hop.
OCT hwRsvpTeResvFwdPolicy	1.3.6.1.4.1.2011.5.25.148.1.4.1.23	OCTET STRING	read-only	The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
I32 hwRsvpTeResvFwdTtl	1.3.6.1.4.1.2011.5.25.148.1.4.1.24	Integer32	read-only	The TTL value in the RSVP header that was last received.
I32 hwRsvpTeResvFwdMsgIdFlag	1.3.6.1.4.1.2011.5.25.148.1.4.1.25	Integer32	read-only	Indicates that the message sender requests the peer to send an acknowledgment for the message. (0x01: ACK desired.)
G32 hwRsvpTeResvFwdMsgIdEpoch	1.3.6.1.4.1.2011.5.25.148.1.4.1.26	Gauge32	read-only	A value that indicates when the Message_Identi- fier sequence has been reset.
G32 hwRsvpTeResvFwdMsgIdNumber	1.3.6.1.4.1.2011.5.25.148.1.4.1.27	Gauge32	read-only	When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the epoch changes or when the value wraps. A return of 0 indicates the absence of the MESSAGE_ID object.
hwRsvpTeIfTable	1.3.6.1.4.1.2011.5.25.148.1.5		not-accessible	The RSVP-specific attributes of the system's interfaces.
hwRsvpTeIfEntry	1.3.6.1.4.1.2011.5.25.148.1.5.1		not-accessible	The RSVP-specific attributes of the a given interface.
G32 hwRsvpTeIfUdpNbrs	1.3.6.1.4.1.2011.5.25.148.1.5.1.1	Gauge32	read-only	The number of neighbors perceived to be using only the RSVP UDP Encapsulation.
G32 hwRsvpTeIfIpNbrs	1.3.6.1.4.1.2011.5.25.148.1.5.1.2	Gauge32	read-only	The number of neighbors perceived to be using only the RSVP IP Encapsulation.
G32 hwRsvpTeIfNbrs	1.3.6.1.4.1.2011.5.25.148.1.5.1.3	Gauge32	read-only	The number of neighbors currently perceived; this will exceed hwRsvpTeIfIpNbrs + hwRsvpTeIfUdpNbrs by the number of neighbors using both encapsu- lations.
I32 hwRsvpTeIfRefreshBlockadeMultiple	1.3.6.1.4.1.2011.5.25.148.1.5.1.4	Integer32	read-only	The value of the RSVP value 'Kb', Which is the minimum number of refresh intervals that blockade state will last once entered.
I32 hwRsvpTeIfRefreshMultiple	1.3.6.1.4.1.2011.5.25.148.1.5.1.5	Integer32	read-only	The value of the RSVP value 'K', which is the number of refresh intervals which must elapse (minimum) before a PATH or RESV message which is not being refreshed will be aged out.
I32 hwRsvpTeIfTtl	1.3.6.1.4.1.2011.5.25.148.1.5.1.6	Integer32	read-only	The value of SEND_TTL used on this interface for messages this node originates. If set to zero, the node determines the TTL via other means.
NUM hwRsvpTeIfRefreshInterval	1.3.6.1.4.1.2011.5.25.148.1.5.1.7	TimeInterval	read-only	The value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given PATH or RESV message on an interface. The default value is 30000.
NUM hwRsvpTeIfRouteDelay	1.3.6.1.4.1.2011.5.25.148.1.5.1.8	TimeInterval	read-only	The approximate period from the time a route is changed to the time a resulting message ap- pears on the interface. The default value is 200.
T/F hwRsvpTeIfEnabled	1.3.6.1.4.1.2011.5.25.148.1.5.1.9	TruthValue	read-only	Its value is always TRUE, if RSVP is enabled on this Interface.
T/F hwRsvpTeIfUdpRequired	1.3.6.1.4.1.2011.5.25.148.1.5.1.10	TruthValue	read-only	If TRUE, manual configuration forces the use of UDP encapsulation on the interface. If FALSE, UDP encapsulation is only used if hwRsvpTeI- fUdpNbrs is not zero.
ROW hwRsvpTeIfStatus	1.3.6.1.4.1.2011.5.25.148.1.5.1.11	RowStatus	read-create	'active' on interfaces that are configured for RSVP.
T/F hwRsvpTeIfHelloEnabled	1.3.6.1.4.1.2011.5.25.148.1.5.1.12	TruthValue	read-only	If TRUE, RSVPTE hello is enabled on this Interface. If FALSE, RSVPTE hello is not enabled on this interface
T/F hwRsvpTeIfSrefreshEnabled	1.3.6.1.4.1.2011.5.25.148.1.5.1.13	TruthValue	read-only	If TRUE, srefresh is enabled on this interface. If FALSE, srefresh is not enabled on this interface.
NUM hwRsvpTeIfSrefreshInterval	1.3.6.1.4.1.2011.5.25.148.1.5.1.14	TimeInterval	read-only	The srefresh interval. I.e. time difference between 2 refreshes. The default value is 30000.
I32 hwRsvpTeIfRetranIncDelta	1.3.6.1.4.1.2011.5.25.148.1.5.1.15	Integer32	read-only	Delta governs the speed with which the sender increases the retransmission interval. The ratio of two successive retransmission intervals is (1 + Delta).
NUM hwRsvpTeIfRetranInterval	1.3.6.1.4.1.2011.5.25.148.1.5.1.16	TimeInterval	read-only	The retransmission interval. The default value is 5000.
T/F hwRsvpTeIfAuthEnabled	1.3.6.1.4.1.2011.5.25.148.1.5.1.17	TruthValue	read-only	If TRUE, authentication is enabled on this interface. If FALSE, authentication is not enabled on this interface.
T/F hwRsvpTeIfAuthEncrypted	1.3.6.1.4.1.2011.5.25.148.1.5.1.18	TruthValue	read-only	This states that authentication key is encrypted or not.
T/F hwRsvpTeIfAuthHandshake	1.3.6.1.4.1.2011.5.25.148.1.5.1.19	TruthValue	read-only	Handshaking is enabled authentications.
NUM hwRsvpTeIfAuthLifeTime	1.3.6.1.4.1.2011.5.25.148.1.5.1.20	TimeInterval	read-only	Authentication life time. The default value is 1800000.
OCT hwRsvpTeIfAuthKey	1.3.6.1.4.1.2011.5.25.148.1.5.1.21	OCTET STRING	read-only	Authentication key, used for authentication processing. For security purposes, a get on this returns a zero length string.
I32 hwRsvpTeIfWindowSize	1.3.6.1.4.1.2011.5.25.148.1.5.1.22	Integer32	read-only	Administrators can specify a message window corresponding to the worst case reordering behavior. For example, one might specify that packets reordered within a 32 message window would be accepted. If no reordering can occur, the window is set to one. The maximum value is 64. The default value is 1.
hwRsvpTeNbrTable	1.3.6.1.4.1.2011.5.25.148.1.6		not-accessible	Information describing the Neighbors of an RSVP system.
hwRsvpTeNbrEntry	1.3.6.1.4.1.2011.5.25.148.1.6.1		not-accessible	Information describing a single RSVP Neigh- bor.
OCT hwRsvpTeNbrAddress	1.3.6.1.4.1.2011.5.25.148.1.6.1.1	OCTET STRING	not-accessible	The IP4 or IP6 Address used by this neighbor. This object may not be changed when the value of the RowStatus object is 'active'.
INT hwRsvpTeNbrProtocol	1.3.6.1.4.1.2011.5.25.148.1.6.1.2	INTEGER	read-only	The encapsulation being used by this neigh- bor.
ROW hwRsvpTeNbrStatus	1.3.6.1.4.1.2011.5.25.148.1.6.1.3	RowStatus	read-create	'active' for all neighbors. This object may be used to configure neighbors. In the pres- ence of configured neighbors, the implementa- tion may (but is not required to) limit the set of valid neighbors to those configured.
G32 hwRsvpTeNbrSendersNumber	1.3.6.1.4.1.2011.5.25.148.1.6.1.4	Gauge32	read-only	The number of senders on the neighbor.
G32 hwRsvpTeNbrReceiversNumber	1.3.6.1.4.1.2011.5.25.148.1.6.1.5	Gauge32	read-only	The number of receivers on the neighbor.
T/F hwRsvpTeNbrHelloEnabled	1.3.6.1.4.1.2011.5.25.148.1.6.1.6	TruthValue	read-only	If TRUE, hello is enabled on the neighbor.
G32 hwRsvpTeNbrHelloSrcInstance	1.3.6.1.4.1.2011.5.25.148.1.6.1.7	Gauge32	read-only	Source instance of the neighbor.
G32 hwRsvpTeNbrHelloDstInstance	1.3.6.1.4.1.2011.5.25.148.1.6.1.8	Gauge32	read-only	Destination instance of the neighbor.
G32 hwRsvpTeNbrHelloLostCounter	1.3.6.1.4.1.2011.5.25.148.1.6.1.9	Gauge32	read-only	The number of times the hello messages have been sent to the neighbor for which hello ACK has not received yet.
INT hwRsvpTeNbrHelloType	1.3.6.1.4.1.2011.5.25.148.1.6.1.10	INTEGER	read-only	Hello type that is being sent to the neighbor. A return of 3[none] indicates that hello is disabled on the nbr.
I32 hwRsvpTeNbrGrCapability	1.3.6.1.4.1.2011.5.25.148.1.6.1.11	Integer32	read-only	Gives neighbor capability to support GR or undergo GR, in case of control plane restart. A mixed value. (0x01: Self GR capability of neighbor; 0x02: GR support capability of neighbor; 0x04: Neighbor capable of receiving RecoveryPath message; 0x08: Neighbor capable of sending RecoveryPath message)
TIM hwRsvpTeNbrGrRestartTime	1.3.6.1.4.1.2011.5.25.148.1.6.1.12	TimeStamp	read-only	Neighbor nodes GR restart time value.
TIM hwRsvpTeNbrGrRecoveryTime	1.3.6.1.4.1.2011.5.25.148.1.6.1.13	TimeStamp	read-only	Neighbor nodes GR recovery time value.
INT hwRsvpTeNbrGrStatus	1.3.6.1.4.1.2011.5.25.148.1.6.1.14	INTEGER	read-only	Neighbor nodes GR status. (0x01, No GR activity; 0x02, Neighbor router is supporting GR; 0x03, Neighbor router is restarting; 0x04, Restart timer is running; 0x05, Recovery timer is running; 0x06, Neighbor GR end.)
OCT hwRsvpTeNbrAuthKeyId	1.3.6.1.4.1.2011.5.25.148.1.6.1.15	OCTET STRING	read-only	Neighbor's authentication key, used for authentication processing. A return of null string indicates the absence of the item. For security purposes, a get on this returns a zero length string.
T/F hwRsvpTeNbrReductionEnabled	1.3.6.1.4.1.2011.5.25.148.1.6.1.16	TruthValue	read-only	If TRUE srefresh is enabled on the neighbor, else srefresh is not enabled on the neighbor.
T/F hwRsvpTeNbrReliabilityEnabled	1.3.6.1.4.1.2011.5.25.148.1.6.1.17	TruthValue	read-only	If TRUE reliability is enabled on the neighbor, else reliability is not enabled on the neighbor.
hwRsvpTeMessageIdTable	1.3.6.1.4.1.2011.5.25.148.1.7		not-accessible	Information describes the MessageIds of an RSVP system.
hwRsvpTeMessageIdEntry	1.3.6.1.4.1.2011.5.25.148.1.7.1		not-accessible	Information describes the MessageIds of an RSVP system.
G32 hwRsvpTeMessageIdEpoch	1.3.6.1.4.1.2011.5.25.148.1.7.1.1	Gauge32	not-accessible	A value that indicates when the Message_Identi- fier sequence has been reset.
G32 hwRsvpTeMessageIdNumber	1.3.6.1.4.1.2011.5.25.148.1.7.1.2	Gauge32	not-accessible	When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the epoch changes or when the value wraps.
INT hwRsvpTeMessageIdFlag	1.3.6.1.4.1.2011.5.25.148.1.7.1.3	INTEGER	read-only	A enumerable value to indicate the type of this Message_Identifier. (1: SenderIncoming; 2: SenderOutgoing; 3: Resv; 4: ResvFwd; 5: RtBuff)
hwRsvpTeFilterSpecTable	1.3.6.1.4.1.2011.5.25.148.1.8		not-accessible	Information describes the FilterSpecs of an RSVP system.
hwRsvpTeFilterSpecEntry	1.3.6.1.4.1.2011.5.25.148.1.8.1		not-accessible	Information describes the FilterSpecs of an RSVP system.
G32 hwRsvpTeFilterSpecNumber	1.3.6.1.4.1.2011.5.25.148.1.8.1.1	Gauge32	not-accessible	The number of this Filter_Spec. This is for SNMP Indexing purposes only and has no relation to any protocol value.
I32 hwRsvpTeFilterSpecLspId	1.3.6.1.4.1.2011.5.25.148.1.8.1.2	Integer32	read-only	A 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself.
OCT hwRsvpTeFilterSpecIngressLsrId	1.3.6.1.4.1.2011.5.25.148.1.8.1.3	OCTET STRING	read-only	IP address for a sender node.
G32 hwRsvpTeFilterSpecLabel	1.3.6.1.4.1.2011.5.25.148.1.8.1.4	Gauge32	read-only	The value of the label arranged by next hop. A return of 4294967295 indicates the absence of the item.
hwRsvpTeRroTable	1.3.6.1.4.1.2011.5.25.148.1.9		not-accessible	Information describes the RRO sub-objects of an RSVP system.
hwRsvpTeRroEntry	1.3.6.1.4.1.2011.5.25.148.1.9.1		not-accessible	Information describes the RRO sub-objects of an RSVP system.
G32 hwRsvpTeRroNumber	1.3.6.1.4.1.2011.5.25.148.1.9.1.1	Gauge32	not-accessible	The number of this RRO sub-object. This is for SNMP Indexing purposes only and has no relation to any protocol value.
INT hwRsvpTeRroType	1.3.6.1.4.1.2011.5.25.148.1.9.1.2	INTEGER	read-only	An enumerable value that indicates the type of this sub-object. (0x01: IPv4 address; 0x02: IPv6 address; 0x03: Label.)
OCT hwRsvpTeRroIpAddr	1.3.6.1.4.1.2011.5.25.148.1.9.1.3	OCTET STRING	read-only	IP address for this sub-object if the type is 'IPv4 address' of 'IPv6 address'. A return of null string indicates the absence of the item.
I32 hwRsvpTeRroIpPrefixLen	1.3.6.1.4.1.2011.5.25.148.1.9.1.4	Integer32	read-only	IP prefix length for this sub-object if the type is 'IPv4 address' of 'IPv6 address'. A return of 0 indicates the absence of the item.
G32 hwRsvpTeRroLabel	1.3.6.1.4.1.2011.5.25.148.1.9.1.5	Gauge32	read-only	The value of the label if the type is 'Label'. A return of 4294967295 indicates the absence of the item.
I32 hwRsvpTeRroFlag	1.3.6.1.4.1.2011.5.25.148.1.9.1.6	Integer32	read-only	If hwRsvpTeRroType is IPv4 or IPv6, it is a mixed value. (0x01: Local protection available; 0x02: Local protection in use; 0x04: bandwidth protection; 0x08: node protection; 0x10: preemption pending; 0x20: node ID.) If hwRsvpTeRroType is Label, 0x01 means global label. A return of zero indicates no bit was set.
hwRsvpTeEroTable	1.3.6.1.4.1.2011.5.25.148.1.10		not-accessible	Information describes the ERO sub-objects of an RSVP system.
hwRsvpTeEroEntry	1.3.6.1.4.1.2011.5.25.148.1.10.1		not-accessible	Information describes the ERO sub-objects of an RSVP system.
G32 hwRsvpTeEroNumber	1.3.6.1.4.1.2011.5.25.148.1.10.1.1	Gauge32	not-accessible	The number of this ERO sub-object. This is for SNMP Indexing purposes only and has no relation to any protocol value.
INT hwRsvpTeEroType	1.3.6.1.4.1.2011.5.25.148.1.10.1.2	INTEGER	read-only	An enumerable value that indicates the type of this sub-object. (0x01: IPv4 address; 0x02: IPv6 address.)
OCT hwRsvpTeEroIpAddr	1.3.6.1.4.1.2011.5.25.148.1.10.1.3	OCTET STRING	read-only	IP address for this sub-object.
I32 hwRsvpTeEroIpPrefixLen	1.3.6.1.4.1.2011.5.25.148.1.10.1.4	Integer32	read-only	IP prefix length for this sub-object.
hwRsvpTeExtendObjects	1.3.6.1.4.1.2011.5.25.148.1.11
hwRsvpTeExtendTrap	1.3.6.1.4.1.2011.5.25.148.1.12
hwRsvpTeTrapObjects	1.3.6.1.4.1.2011.5.25.148.1.12.1
IP hwRsvpTeNbr	1.3.6.1.4.1.2011.5.25.148.1.12.1.1	IpAddress	accessible-for-notify	IP address of RSVP neighbour.
I32 hwRsvpTeIfNbrCurrentCount	1.3.6.1.4.1.2011.5.25.148.1.12.1.2	Integer32	accessible-for-notify	Number of existing neighbors of the RSVP interface.
I32 hwRsvpTeIfNbrThreshold	1.3.6.1.4.1.2011.5.25.148.1.12.1.3	Integer32	accessible-for-notify	Threshold for the number of neighbors of the RSVP interface.
I32 hwRsvpTeIfNbrTotalCount	1.3.6.1.4.1.2011.5.25.148.1.12.1.4	Integer32	accessible-for-notify	Maximum number of allowed neighbors of the RSVP interface.
STR hwRsvpTeIfName	1.3.6.1.4.1.2011.5.25.148.1.12.1.5	DisplayString	accessible-for-notify	The name of the RSVP interface.
hwRsvpTeTrap	1.3.6.1.4.1.2011.5.25.148.1.12.2
NTF hwRsvpTeHelloLost	1.3.6.1.4.1.2011.5.25.148.1.12.2.1			Indicates neighbour of RSVP hello lost.
NTF hwRsvpTeHelloLostRecovery	1.3.6.1.4.1.2011.5.25.148.1.12.2.2			Indicates neighbour of RSVP hello lost.
NTF hwRsvpTeAuthFail	1.3.6.1.4.1.2011.5.25.148.1.12.2.3			Indicates neighbour of RSVP hello lost.
NTF hwRsvpTeAuthSuccess	1.3.6.1.4.1.2011.5.25.148.1.12.2.4			Indicates neighbour of RSVP hello lost.
NTF hwRsvpTeIfNbrThresholdExceed	1.3.6.1.4.1.2011.5.25.148.1.12.2.5			Indicates that the number of RSVP interface neighbors has exceeded the upper threshold.
NTF hwRsvpTeIfNbrThresholdExceedClear	1.3.6.1.4.1.2011.5.25.148.1.12.2.6			Indicates that the number of RSVP interface neighbors has fallen below the lower threshold.
NTF hwRsvpTeIfNbrTotalCountExceed	1.3.6.1.4.1.2011.5.25.148.1.12.2.7			Indicates that the number of RSVP interface neighbors has reached the maximum number.
NTF hwRsvpTeIfNbrTotalCountExceedClear	1.3.6.1.4.1.2011.5.25.148.1.12.2.8			Indicates that the number of RSVP interface neighbors has fallen below the recovery number.
hwRsvpTeConformance	1.3.6.1.4.1.2011.5.25.148.2
hwRsvpTeGroups	1.3.6.1.4.1.2011.5.25.148.2.1
hwRsvpTeSessionGroup	1.3.6.1.4.1.2011.5.25.148.2.1.1			These objects are required for RSVP Systems.
hwRsvpTeSenderGroup	1.3.6.1.4.1.2011.5.25.148.2.1.2			These objects are required for RSVP Systems.
hwRsvpTeResvGroup	1.3.6.1.4.1.2011.5.25.148.2.1.3			These objects are required for RSVP Systems.
hwRsvpTeResvFwdGroup	1.3.6.1.4.1.2011.5.25.148.2.1.4			These objects are optional, used for some RSVP Systems.
hwRsvpTeIfGroup	1.3.6.1.4.1.2011.5.25.148.2.1.5			These objects are required for RSVP Systems.
hwRsvpTeNbrGroup	1.3.6.1.4.1.2011.5.25.148.2.1.6			These objects are required for RSVP Systems.
hwRsvpTeMessageIdGroup	1.3.6.1.4.1.2011.5.25.148.2.1.7			Description.
hwRsvpTeFilterSpecGroup	1.3.6.1.4.1.2011.5.25.148.2.1.8			Description.
hwRsvpTeRroGroup	1.3.6.1.4.1.2011.5.25.148.2.1.9			Description.
hwRsvpTeEroGroup	1.3.6.1.4.1.2011.5.25.148.2.1.10			Description.
hwRsvpTeTrapObjectsGroup	1.3.6.1.4.1.2011.5.25.148.2.1.11			Description.
hwRsvpTeTrapGroup	1.3.6.1.4.1.2011.5.25.148.2.1.12			Description.
hwRsvpTeCompliances	1.3.6.1.4.1.2011.5.25.148.2.2
hwRsvpTeCompliance	1.3.6.1.4.1.2011.5.25.148.2.2.1			The compliance statement. Note that the im- plementation of this module requires implemen- tation of the Integrated Services MIB as well.

RFC description

Manages RSVP-TE (Resource Reservation Protocol - Traffic Engineering) for QoS and traffic engineering in MPLS networks.

Start monitoring Huawei MPLS router (RSVP-TE traffic-engineered tunnels) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-RSVPTE-MIB