All MIBs › APEX-MIB
Organization: Motorola Connected Home Solutions
Last Updated: 2011-02-15
Category: Device Management
Description: BigBand Networks APEX video gateway configuration, channel management, and stream status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is APEX-MIB?
APEX-MIB is a proprietary MIB from BigBand Networks for the APEX video/broadband gateway platform, a headend/edge device used in cable and DOCSIS video networks for processing and inserting conditional-access data into MPEG transport streams. It exposes configuration data covering device identity and boot behavior (product name, boot method, auto-reboot setting), EMM (Entitlement Management Message) insertion parameters for conditional-access PID mapping, and a save-config action object. Monitoring here spans both software-configuration and hardware-reboot status: apexBootReason reveals why the device last restarted, useful for catching unexpected crashes versus scheduled reboots, apexAutoRebootEnable and apexSaveConfig relate to configuration persistence and recovery behavior, and apexMaxServiceMappings indicates the device's current capacity utilization for service mappings. It is a standalone BigBand Networks proprietary MIB likely used alongside the related APEX9-MIB and other BigBand video-headend MIBs sharing the same enterprise OID branch. It is deployed at cable/MSO video headends running BigBand APEX gateways for digital video processing and conditional-access EMM insertion into broadcast transport streams. Engineers can download the APEX-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in APEX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- BigBand Networks APEX video/broadband gateway
Monitoring Examples
An administrator would poll apexBootReason after an unexpected outage to determine whether the APEX gateway rebooted due to a crash or a scheduled event, and check apexAutoRebootEnable to confirm the recovery policy is set as intended. Monitoring apexMcEmmInsertionMode alongside apexMcEmmInsertionPid1 and apexMcEmmInsertionPid2 (with their Enable flags) verifies conditional-access EMM insertion is correctly configured for the expected PIDs. apexMaxServiceMappings shows how close the device is to its configured service-mapping capacity, useful before provisioning additional services.
What Can Be Monitored
- last boot reason
- auto-reboot configuration
- EMM insertion mode and PID configuration
- service mapping capacity
- configuration save status
This MIB depends on
Related MIBs
Imported Objects
From BCS-IDENT-MIB
| giproducts | OBJECT-IDENTITY |
From BCS-TRAPS-MIB
| trapAdditionalInfoInteger1 | OBJECT-TYPE |
| trapAdditionalInfoInteger2 | OBJECT-TYPE |
| trapAdditionalInfoInteger3 | OBJECT-TYPE |
| trapChangedObjectId | OBJECT-TYPE |
| trapChangedValueDisplayString | OBJECT-TYPE |
| trapChangedValueInteger | OBJECT-TYPE |
| trapChangedValueIpAddress | OBJECT-TYPE |
| trapChangedValueOID | OBJECT-TYPE |
| trapIdentifier | OBJECT-TYPE |
| trapNETrapLastTrapTimeStamp | OBJECT-TYPE |
| trapNetworkElemAdminState | OBJECT-TYPE |
| trapNetworkElemAlarmStatus | OBJECT-TYPE |
| trapNetworkElemAvailStatus | OBJECT-TYPE |
| trapNetworkElemModelNumber | OBJECT-TYPE |
| trapNetworkElemOperState | OBJECT-TYPE |
| trapNetworkElemSerialNum | OBJECT-TYPE |
| trapPerceivedSeverity | OBJECT-TYPE |
| trapSequenceId | OBJECT-TYPE |
| trapText | OBJECT-TYPE |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString |
How to Use in IPNetwork Monitor
Example using apexRdsProgramMessagesReceived OID:
Select a BigBand Networks APEX video/broadband gateway (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type apexRdsProgramMessagesReceived into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of successful ServiceEncrypt messages received in the last 15 minutes. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| apex | 1.3.6.1.4.1.1166.1.31 | The MIB module for the APEX. | ||
| apexAcp | 1.3.6.1.4.1.1166.1.31.17 | |||
| apexAcpConfig | 1.3.6.1.4.1.1166.1.31.17.1 | |||
| apexAcpConfigGeneral | 1.3.6.1.4.1.1166.1.31.17.1.1 | |||
| I32 apexAcpEvenCsn | 1.3.6.1.4.1.1166.1.31.17.2.2.1.4 | Integer32 | read-only | The Even Category Sequence Number of the ACP. Should match the even CSN assigned by DAC, if not may indicate a communications problem. |
| I32 apexAcpHealthByte | 1.3.6.1.4.1.1166.1.31.17.2.2.1.3 | Integer32 | read-only | The health byte of the ACP. Indicates whether the ACP has intact fuses. The health should read 255 (hex 0xFF) for all APEX ACPs. Otherwise, the ACP will not properly function. |
| I32 apexAcpOddCsn | 1.3.6.1.4.1.1166.1.31.17.2.2.1.5 | Integer32 | read-only | The Odd Category Sequence Number of the ACP. Should match the odd CSN assigned by DAC, if not may indicate a communications problem. |
| apexAcpStatus | 1.3.6.1.4.1.1166.1.31.17.2 | |||
| apexAcpStatusEntry | 1.3.6.1.4.1.1166.1.31.17.2.2.1 | not-accessible | Output Program Table Entry. | |
| apexAcpStatusGeneral | 1.3.6.1.4.1.1166.1.31.17.2.1 | |||
| I32 apexAcpStatusIndex | 1.3.6.1.4.1.1166.1.31.17.2.2.1.1 | Integer32 | not-accessible | Acp Status Index. Index for one of six control word generating ACPs. |
| apexAcpStatusTable | 1.3.6.1.4.1.1166.1.31.17.2.2 | not-accessible | This table shows the status of the Control Word Generating ACPs. | |
| STR apexAcpUnitAddress | 1.3.6.1.4.1.1166.1.31.17.2.2.1.2 | DisplayString | read-only | The unit address of the ACP in ASCII Hex. The Unit address is a 5 byte value. |
| I32 apexAcpUnitAttribute | 1.3.6.1.4.1.1166.1.31.17.2.2.1.6 | Integer32 | read-only | Unit attribute byte is made available to verify that the MC2.1 was properly unit created during factory production. |
| INT apexAlarmChassisRedundancyAvailabilityFault | 1.3.6.1.4.1.1166.1.31.100.8092 | INTEGER | read-only | Generated when redundancy status is unavailable (except for link loss) configuration not synchronized secondary in fault state Cleared when redundancy status is available or redundancy disabled. |
| INT apexAlarmChassisRedundancyConfigurationFault | 1.3.6.1.4.1.1166.1.31.100.8094 | INTEGER | read-only | Generated when primary APEX receives heartbeat from another primary. Critical if APEX was in active state (sourcing broadcast content) Major if APEX was in standby state (broadcast ports muted). Cleared when primary APEX receives heartbeat from a secondary, configuration is changed to secondary, or redundancy is disabled. |
| INT apexAlarmChassisRedundancyLinkFault | 1.3.6.1.4.1.1166.1.31.100.8093 | INTEGER | read-only | Generated when ENET2 link is lost Cleared when ENET 2 link is present or redundancy disabled. |
| INT apexAlarmChassisRedundancyPrimaryFailover | 1.3.6.1.4.1.1166.1.31.100.8090 | INTEGER | read-only | Generated when the primary active APEX fails over to the secondary standby unit. Trap tells if failover is operator induced, or automatic because of a fault. Major if automatic due to some fault Warning if force-failover. Cleared when redundancy is disabled or when the primary becomes active and the secondary is standby. |
| INT apexAlarmChassisRedundancySecondaryFailover | 1.3.6.1.4.1.1166.1.31.100.8091 | INTEGER | read-only | Generated when the secondary active APEX fails over to the primary standby unit. Trap tells if failover is operator induced, or automatic because of a fault. Major if automatic due to some fault Warning if force-failover. Cleared when redundancy is disabled or when the secondary becomes active and the primary is standby. |
| INT apexAlarmDepiControlConnectionFault | 1.3.6.1.4.1.1166.1.31.100.8080 | INTEGER | read-only | DEPI Control connection setup Fault. |
| INT apexAlarmDepiSessionSetupFault | 1.3.6.1.4.1.1166.1.31.100.8081 | INTEGER | read-only | DEPI Session Setup Fault. |
| INT apexAlarmDtiSyncLossFault | 1.3.6.1.4.1.1166.1.31.100.8082 | INTEGER | read-only | EQAM lost SYNC with the DTI Server. |
| INT apexAlarmFanFault | 1.3.6.1.4.1.1166.1.31.100.8003 | INTEGER | read-only | 'major' indicates one or more fans has reduced RPM readings. |
| INT apexAlarmGbeBufferFullness | 1.3.6.1.4.1.1166.1.31.100.8021 | INTEGER | read-only | Gigabit Ethernet Frame Buffer Fullness Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Frame buffers are about to or have overflowed. The overflow level is based on the actual input data rate. 'major' when the frame buffer crosses a user specified threshold (apexGbeConfigFrameBufferAlarmThreshold). Cleared when the buffer level drops below the threshold. 'critical' when the frame buffer is completely full and frames are being dropped. Cleared when the overflow condition stops. A Major alarm, depending on the threshold setting, indicates that the APEX is getting close to overflowing it's internal Gigabit Ethernet frame buffers. A Critical alarm indicates that the frame buffer levels have overflowed. This will cause loss of packets and may result in tiling and other output anomalies. |
| INT apexAlarmGbeInputStreamHighBitRate | 1.3.6.1.4.1.1166.1.31.100.8023 | INTEGER | read-only | Gigabit Ethernet Input Stream High Bit Rate Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams as configured in apexManRteGbeInRedTable or via a Session Controller have a high bit rate condition. For alarm status of each stream refer to entry apexGbeStatInTsPriHighBitRateAlarm and apexGbeStatInTsSecHighBitRateAlarm. 'major' when one or more stream bit rates are above their apexManRteGbeInRedPriHighAlarmBitRate or apexManRteGbeInRedSecHighAlarmBitRate. Clears when all streams have been restored to at or below their configured apexManRteGbeInRedPriHighAlarmBitRate or apexManRteGbeInRedSecHighAlarmBitRate. |
| INT apexAlarmGbeInputStreamLowBitRate | 1.3.6.1.4.1.1166.1.31.100.8022 | INTEGER | read-only | Gigabit Ethernet Input Stream Low Bit Rate Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams as configured in apexManRteGbeInRedTable have a low bit rate condition. For alarm status of each stream refer to entries apexGbeStatInTsPriLowBitRateAlarm and apexGbeStatInTsSecLowBitRateAlarm. 'major' when one or more stream bit rates are below their apexManRteGbeInRedPriLowAlarmBitRate or apexManRteGbeInRedSecLowAlarmBitRate. Clears when all streams have been restored to at or above their configured apexManRteGbeInRedPriLowAlarmBitRate or apexManRteGbeInRedSecLowAlarmBitRate. |
| INT apexAlarmGbeInterfaceRedundFailOver | 1.3.6.1.4.1.1166.1.31.100.8029 | INTEGER | read-only | Gigabit Ethernet Interface Redundant Fail Over Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet interfaces have Failed Over to the Secondary interface. The APEX determines an interface as failed when link has been lost. 'major' when one or more Primary interfaces have failed over to the Secondary. Clears when all Primary interfaces have been restored and the APEX has switched back to the Primary from the Secondary. |
| INT apexAlarmGbeLossOfInputStream | 1.3.6.1.4.1.1166.1.31.100.8027 | INTEGER | read-only | Loss of Gbe Input Stream Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams is missing. A missing input stream is determined based on user configured data or stream rate and detection timeout value. This alarm is only applicable when the input streams are configured to be monitored for loss of input stream. This alarm occurs on the first error. It is not issued for additional errors. It is cleared when all errors are cleared. |
| INT apexAlarmGbeLossOfPhysicalInput | 1.3.6.1.4.1.1166.1.31.100.8020 | INTEGER | read-only | Loss of Physical Gigabit Ethernet Input Alarm. 'critical' indicates that one or more physical interfaces that are configured as enabled to receive input have a failure (apexGbeStatusLossOfPhysicalInput). Physical input interfaces can be disabled to prevent this alarm when no input is connected. |
| INT apexAlarmGbeMptsRedundFailOver | 1.3.6.1.4.1.1166.1.31.100.8025 | INTEGER | read-only | Gigabit Ethernet Input MPTS Redundant Fail Over Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams configured in apexManRteGbeInRedTable as being the Primary stream of a Redundant Pair have Failed Over to the Secondary stream. For alarm status of each stream refer to entry apexGbeStatInTsMptsRedundFailAlarm. 'major' when one or more Redundant Primary streams have failed over to the Secondary. Clears when all Primary streams have been restored and the APEX has switched back to the Primary from the Secondary. |
| INT apexAlarmGbeMptsRedundPrimaryThreshold | 1.3.6.1.4.1.1166.1.31.100.8024 | INTEGER | read-only | Gigabit Ethernet Input MPTS Redundant Primary Stream Below Threshold Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams configured in apexManRteGbeInRedTable as being the Primary stream of a Redundant Pair are below the configured threshold. For alarm status of each stream refer to entry apexGbeStatInTsMptsRedundPriAlarm. 'major' when one or more stream bit rates are below their threshold as specified in apexManRteGbeInRedThreshold. Clears when all streams have been restored to at or above their configured apexManRteGbeInRedThreshold. |
| INT apexAlarmGigeToHostCommFault | 1.3.6.1.4.1.1166.1.31.100.8028 | INTEGER | read-only | Loss of Communications from Gige to Host Alarm. This alarm is used to inform the user when the Host processor is no longer receiving periodic status messages from the Gige processor. This alarm occurs on the first error. It is not issued for additional errors. It is cleared when the condition is resolved. |
| INT apexAlarmHardwareFault | 1.3.6.1.4.1.1166.1.31.100.8000 | INTEGER | read-only | Indicates that a Hardware related error occurred. Examples include missing or uncommunicative HW, failures in initialization of HW, and failures to configure HW. These can occur at startup or when the system is operational. Types of HW Faults include: Application File(s) Download failure; SPI Interface Initialization failure; PCI Interface Initialization failure; GigE Configuration failure; MUX Configuration failure; QAM Module Communication failure; Unsupported/Incorrect HW/FW Version (QAM, etc.); Fatal Host Firmware Exception. 'critical' indicates a fatal error occurred that prevents the APEX from performing operational requirements. 'warning' indicates an error that does not prevent the APEX from performing operational requirements. |
| INT apexAlarmInvalidInitData | 1.3.6.1.4.1.1166.1.31.100.8001 | INTEGER | read-only | Set when invalid Initialization data (ini files) is encountered. |
| INT apexAlarmOutputOverflow | 1.3.6.1.4.1.1166.1.31.100.8041 | INTEGER | read-only | Output Transport Stream Overflow Alarm. 'critical' when apexOutputTsUtilizOverflow occurs for an OTS. The alarm will clear when OTS no longer in overflow. |
| INT apexAlarmOutputUtilizationFault | 1.3.6.1.4.1.1166.1.31.100.8040 | INTEGER | read-only | Output Transport Stream Utilization Threshold Alarm. 'minor' when apexOutputTsUtilMonAlarmThreshold is met or exceeded for apexOutputTsUtilMonSetAlarmDelay for an OTS. The alarm will clear after the OTS remains below apexOutputTsUtilMonAlarmThreshold for apexOutputTsUtilMonClearAlarmDelay. |
| INT apexAlarmPowerFault | 1.3.6.1.4.1.1166.1.31.100.8004 | INTEGER | read-only | Power Supply Fault Alarm. 'warning' indicates power supply not compatible (apexPsStatusInstalled). 'major' indicates power supply or fan only module) removed (apexPsStatusInstalled). 'major' indicates power supply input power fault (apexPsStatusInputPowerStatus), output power fault (apexPsStatusOutputPowerStatus), or comm fault (apexPsStatusCommError). 'critical' indicates power supply over temperature fault (apexPsStatusTemperatureStatus). |
| INT apexAlarmQamChannelFault | 1.3.6.1.4.1.1166.1.31.100.8044 | INTEGER | read-only | QAM Channel Fault Alarm. 'critical' when any or all of the QAM Channel errors enumerated in apexQamChanStatError occur on a QAM channel. The alarm will clear after all faults clear on the QAM channel. The current alarm status on a QAM channel basis can be found in apexQamChanStatFaultCondition. |
| INT apexAlarmQamModuleFault | 1.3.6.1.4.1.1166.1.31.100.8042 | INTEGER | read-only | QAM Port Fault Alarm. 'major' when apexQamModuleStatError occurs when all QAM channels on the QAM Module have apexQamChanStatActive of not 'active'. 'critical' when apexQamModuleStatError occurs when all QAM channels on the QAM Module have apexQamChanStatActive of 'active'. The alarm will clear after all faults clear on the QAM Module. The current alarm status on a QAM Module basis can be found in apexQamModuleStatFaultCondition. |
| INT apexAlarmQamRfPortFault | 1.3.6.1.4.1.1166.1.31.100.8043 | INTEGER | read-only | QAM RF Port Fault Alarm. 'major' when power voltage or output RF level error occurs on the RF Port. 'critical' when clock, PLL, or data sync error occurs on the RF Port. The alarm will clear after all faults clear for the RF Port. The current alarm status on an RF port basis can be found in apexQamRfPortStatFaultCondition. |
| INT apexAlarmQamRfRedundFailOver | 1.3.6.1.4.1.1166.1.31.100.8045 | INTEGER | read-only | QAM RF Redundancy Fail Over Alarm. 'major' when the backup QAM RF Port status is 'active' (apexQamRfRedundStatusBackupPort). This occurs when a primary QAM RF Port has failed over to the backup RF Port or the user has forced a primary to the backup. The alarm will clear when the backup QAM RF Port status returns to 'standby'. The alarm is relevant only when apexQamRfRedundConfigEnable is 'enabled'. The current QAM RF Port that is active on the backup port can be found in apexQamRfRedundStatusFailedPort. |
| INT apexAlarmQamRfRedundMismatch | 1.3.6.1.4.1.1166.1.31.100.8046 | INTEGER | read-only | QAM RF Redundancy Mismatch Alarm. 'warning' when channels could be lost on QAM RF Fail Over to backup or on Switch Back to primary. Refer to apexQamRfRedundStatusMismatch for more information. The alarm will clear when mismatch condition clears. The alarm is relevant only when apexQamRfRedundConfigEnable is 'enabled'. |
| INT apexAlarmRdsCommFault | 1.3.6.1.4.1.1166.1.31.100.8060 | INTEGER | read-only | RDS Communication Fault. 'major' when experiencing an RDS communication fault. The alarm will clear when RDS connection is restored. |
| INT apexAlarmRemCommFault | 1.3.6.1.4.1.1166.1.31.100.8070 | INTEGER | read-only | REM Communication Fault. 'major' when experiencing an REM communication fault. The alarm will clear when REM connection is restored. Refer to apexQamRfRedundStatusRemConnection for more information. The alarm is relevant only when apexQamRfRedundConfigEnable is 'enabled' and apexQamRfRedundConfigRemConnection is not 'none'. |
| INT apexAlarmRemFault | 1.3.6.1.4.1.1166.1.31.100.8071 | INTEGER | read-only | REM Fault. 'warning' when REM is reporting a 0x05 error code. 'major' when error received from REM (other than 0x05) or REM is reporting incorrect switch configuration. The alarm will clear when REM errors clear. Refer to apexQamRfRedundStatusRemError and apexQamRfRedundStatusRemSwitch for more information. The alarm is relevant only when apexQamRfRedundConfigEnable is 'enabled' and apexQamRfRedundConfigRemConnection is not 'none'. |
| INT apexAlarmRtspControllerCommFault | 1.3.6.1.4.1.1166.1.31.100.8050 | INTEGER | read-only | RTSP Controller Communication Fault. 'major' when the RTSP Controller is experiencing a communication fault. The alarm will clear when connection is restored the RTSP controller. |
| apexAlarms | 1.3.6.1.4.1.1166.1.31.100 | |||
| INT apexAlarmServiceInError | 1.3.6.1.4.1.1166.1.31.100.8026 | INTEGER | read-only | Alarm Service In Error. 'major' indicates that one or more services is in error (unable to fully continue processing). However, this is only for very specific errors where the error could be caused by either the input stream being invalid or another command along with the input stream is causing the error. For example, if mapping an input service to an output and that PMT is not referenced in the PAT, or the number of PIDs in the PMT is greater than the number of PIDs supported, then the command is in error. This error condition would be cleared if a new PAT is received referencing the PMT or in the other case, if a new PMT is received referencing a valid number of PIDs. Refer to apexOutputProgramRoutingStatus for more information. This alarm occurs on the first error. It is not issued for additional errors. It is cleared when all errors are cleared. |
| INT apexAlarmTemperatureFault | 1.3.6.1.4.1.1166.1.31.100.8002 | INTEGER | read-only | 'critical' indicates one or more temperature sensors is reporting a high temperature condition. |
| apexAncillaryPidMapping | 1.3.6.1.4.1.1166.1.31.11 | |||
| apexAsi | 1.3.6.1.4.1.1166.1.31.5 | |||
| apexAsiConfig | 1.3.6.1.4.1.1166.1.31.5.1 | |||
| apexAsiMonitorPortConfig | 1.3.6.1.4.1.1166.1.31.5.1.2 | |||
| INT apexAsiMonitorPortEncryption | 1.3.6.1.4.1.1166.1.31.5.1.2.2 | INTEGER | read-write | Selects pre or post encryption for the ASI monitor port. This parameter is only applicable to APEXs with encryption capability. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexAsiMonitorPortOutputTsNum | 1.3.6.1.4.1.1166.1.31.5.1.2.1 | Integer32 | read-write | The number of the output transport stream to route to the ASI Monitor Port. Zero indicates that no stream is to be routed to the ASI Monitor port. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexAutoRebootEnable | 1.3.6.1.4.1.1166.1.31.1.1.1.4 | EnableDisableTYPE | read-write | Setting to 'enabled' allows the APEX to automatically reboot when specific APEX hardware errors occur. Setting this to Enabled will cause the APEX to automatically reboot upon specific HW faults, such as a GigE processor crash, or upon a Host processor watchdog event. When disabled, HW faults and watchdog events will not cause an automatic reboot. This is useful when it is necessary to debug the event (to allow time to gather status prior to manually rebooting). Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexBootMethod | 1.3.6.1.4.1.1166.1.31.1.1.1.3 | INTEGER | read-write | This parameter is used to set the boot method for the APEX. Selection of noDhcpOrBootp means the APEX will not use DHCP or BOOTP - this will result in about a 10 second savings in boot time. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexBootReason | 1.3.6.1.4.1.1166.1.31.1.2.1.1 | INTEGER | read-only | Indicates reason for APEX boot: 'powerCycle' - Power-up or power cycled. 'operatorReboot' - Operator commanded reboot (refer to manual). 'hwFault' - Automatic reboot occurred as per apexAutoRebootEnable. 'wdFault' - Automatic Watchdog reboot as per apexAutoRebootEnable. |
| apexChassisRedundancy | 1.3.6.1.4.1.1166.1.31.22 | |||
| INT apexChassisRedundancyCommunicationStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.4 | INTEGER | read-only | This parameter is applicable for an APEX where chassis redundancy is enabled. This parameter will report the chassis redundancy communication status. These are based on its knowledge about the secondary APEX from heartbeat messages. The APEX configured as primary will report the following values: disconnected(0): No heartbeat messages are received from secondary or communication timed out. connected(1): Heartbeat messages are received from secondary and communication has not timed out. The APEX configured as secondary will report the following values: disconnected(0): No heartbeat messages are received from primary or communication timed out. connected(1): Heartbeat messages are received from primary and communication has not timed out. |
| apexChassisRedundancyConfig | 1.3.6.1.4.1.1166.1.31.22.1 | |||
| APP apexChassisRedundancyConfigApplyChange | 1.3.6.1.4.1.1166.1.31.22.1.1.16 | ApplyDataToDeviceTYPE | read-write | The Apply for Chassis Redundancy Configuration parameters. This parameter MUST be set to 'apply' in order for the data to take effect. This parameter MUST be set LAST after all Chassis Redundancy parameters affected by this parameter have been configured. @Config(config=no, reboot=no) |
| ENA apexChassisRedundancyConfigEnable | 1.3.6.1.4.1.1166.1.31.22.1.1.1 | EnableDisableTYPE | read-write | This is to enable/disable APEX chassis redundancy. When set to disabled(1), APEX is not allowed to failover. When set to enabled(2), APEX can failover on its redundant APEX. Once written, the change to this parameter will only take immediate effect after apexChassisRedundancyConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexChassisRedundancyConfigGeneral | 1.3.6.1.4.1.1166.1.31.22.1.1 | |||
| INT apexChassisRedundancyConfigurationStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.5 | INTEGER | read-only | This parameter is applicable for an APEX where chassis redundancy is enabled. This parameter will report the chassis redundancy configuration status. These are based on its knowledge about the secondary APEX from heartbeat messages. The APEX configured as primary will report the following values: unknown(0): Secondary configuration is not known or secondary is not connected. synchronized(1): Secondary has same configuration as primary (except for QAM outputs). outofsync(2): Secondary configuration is not in sync with primary. The APEX configured as secondary will report the following values: unknown(0): Primary configuration is not known or primary is not connected. synchronized(1): Primary has same configuration as secondary (except for QAM outputs). outofsync(2): Primary configuration is not in sync with secondary. |
| IP apexChassisRedundancyCurrHBIntfIPStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.13 | IpAddress | read-only | This parameter indicates the heartbeat interface used for receiving heartbeat from the redundant APEX. |
| STR apexChassisRedundancyEventDescription | 1.3.6.1.4.1.1166.1.31.200.7.1.3 | DisplayString | read-only | Text string describing the event. |
| apexChassisRedundancyEventEntry | 1.3.6.1.4.1.1166.1.31.200.7.1 | not-accessible | Chassis Redundancy Event Table Entry. | |
| I32 apexChassisRedundancyEventIndex | 1.3.6.1.4.1.1166.1.31.200.7.1.1 | Integer32 | not-accessible | Index for Chassis Redundancy Event table. |
| apexChassisRedundancyEventTable | 1.3.6.1.4.1.1166.1.31.200.7 | not-accessible | Table of Chassis Redundancy Events. Maximum of 300 events will be recorded. | |
| I32 apexChassisRedundancyEventTimeLogged | 1.3.6.1.4.1.1166.1.31.200.7.1.2 | Integer32 | read-only | Time in GPS seconds (apexSystemTime) that this event was logged. |
| ENA apexChassisRedundancyFailOverEnet1LinkLoss | 1.3.6.1.4.1.1166.1.31.22.1.1.10 | EnableDisableTYPE | read-write | Configures if ENET1 link loss is cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexChassisRedundancyFailOverEnet2LinkLoss | 1.3.6.1.4.1.1166.1.31.22.1.1.11 | EnableDisableTYPE | read-write | Configures if ENET2 link loss is cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexChassisRedundancyFailOverGigE12LinkLoss | 1.3.6.1.4.1.1166.1.31.22.1.1.8 | EnableDisableTYPE | read-write | Configures if both GigE 1&2 link loss is cause for a failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexChassisRedundancyFailOverGigE34LinkLoss | 1.3.6.1.4.1.1166.1.31.22.1.1.9 | EnableDisableTYPE | read-write | Configures if both GigE 3&4 experience link loss is cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexChassisRedundancyFailOverQamChannelFault | 1.3.6.1.4.1.1166.1.31.22.1.1.15 | EnableDisableTYPE | read-write | Configures if a QAM channel fault is a cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexChassisRedundancyFailOverQamModuleFault | 1.3.6.1.4.1.1166.1.31.22.1.1.13 | EnableDisableTYPE | read-write | Configures if a QAM module fault is a cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexChassisRedundancyFailOverQamRfPortFault | 1.3.6.1.4.1.1166.1.31.22.1.1.14 | EnableDisableTYPE | read-write | Configures if a QAM RF port fault is a cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexChassisRedundancyFailOverTemperatureFault | 1.3.6.1.4.1.1166.1.31.22.1.1.12 | EnableDisableTYPE | read-write | Configures if the temperature fault is a cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexChassisRedundancyFirmwareMismatchStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.10 | INTEGER | read-only | This parameter indicates whether the Firmware version of the apexes in Chassis Redundancy pair match. Both the APEXs will report the following values: These are based on its knowledge about the secondary APEX Firmware version from heartbeat messages. unknown (0): Firmware version of pair APEX is not known (heartbeat not received). match (1): Firmware version of APEXs in redundancy pair match. mismatch (2): Firmware version of APEXs in redundancy pair do not match. |
| INT apexChassisRedundancyForceFailOver | 1.3.6.1.4.1.1166.1.31.22.1.1.7 | INTEGER | read-write | When set to failover(2), this results in the APEX unit failing over if it is in active state and the redundant APEX is in standby state. If the condition above is not met, setting the value to failvoer(2) has no effect. @Config(config=no, reboot=no) |
| STR apexChassisRedundancyGeneralConfigSyncStatusText | 1.3.6.1.4.1.1166.1.31.22.2.1.7 | DisplayString | read-only | GigE Config Sync Error info |
| INT apexChassisRedundancyGigE12LinkStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.11 | INTEGER | read-only | This parameter indicates the combined alarm status of the GigE 1 and GigE 2. Indicates the lower of the gigE input interface alarm conditions. ok (1): No alarm on either of GigE1 and GigE2. warning (3): Warning alarm on both GigE1 or GigE2 minor (4): minor alarm on both GigE1 or GigE2 major (5): Major alarm on both GigE1 or GigE2 critical (6): critical alarm on both GigE1 and GigE2. |
| INT apexChassisRedundancyGigE34LinkStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.12 | INTEGER | read-only | This parameter indicates the combined alarm status of the GigE3 and GigE4. Indicates the lower of the gigE input interface alarm conditions. ok (1): No alarm on either of GigE3 and GigE4. warning (3): Warning alarm on both GigE3 or GigE4 minor (4): minor alarm on both GigE3 or GigE4 major (5): Major alarm on both GigE3 or GigE4 critical (6): critical alarm on both GigE3 and GigE4. |
| INT apexChassisRedundancyGigEMismatchStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.8 | INTEGER | read-only | This parameter indicates whether the GigE configuration of the apexes in Chassis Redundancy pair match. Both the APEXs will report the following values: These are based on its knowledge about the secondary APEX GigE configuration from heartbeat messages. unknown (0): GigE configuration of pair APEX is not known (heartbeat not received). match (1): GigE configuration of APEXs in redundancy pair match. mismatch (2): GigE configuration of APEXs in redundancy pair do not match. |
| INT apexChassisRedundancyMode | 1.3.6.1.4.1.1166.1.31.22.1.1.2 | INTEGER | read-write | Configures the desired role of APEX. Primary has active output ports, secondary is inactive with output ports muted. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexChassisRedundancyMulticastRedundancyMode | 1.3.6.1.4.1.1166.1.31.22.1.1.3 | INTEGER | read-write | This is used to process route mappings by the standby APEX. When set to hot(0) on standby APEX, all the routes processed by the active APEX will also be processed by standby APEX. When set to warm(1) on standby APEX, all the routes processed by the active APEX will be muted by standby APEX. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexChassisRedundancyPrimaryApexStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.1 | INTEGER | read-only | This parameter is applicable for an APEX where chassis redundancy is enabled. The APEX configured as primary will report the following values: active(1): Primary RF outputs are active. standby(2): Primary RF outputs are muted. Waiting to become active. fault(3): Primary has experienced a fault. suspend(4): Primary is suspended. The APEX configured as secondary will report the following values. These are based on its knowledge about the primary APEX from heartbeat messages. unknown(0): State of primary is not known (heartbeat not received). active(1): Primary RF outputs are active. standby(2): Primary RF outputs are muted. Waiting to become active. fault(3): Primary has experienced a fault. suspend(4): Primary is suspended. |
| ENA apexChassisRedundancyPrimaryStandbyOverride | 1.3.6.1.4.1.1166.1.31.22.1.1.17 | EnableDisableTYPE | read-write | This parameter is set to ENABLED while configuring the apex as primary apex. If this parameter is set, the apex will goto ACTIVE state irrespective of secondary status. @Config(config=no, reboot=no) |
| INT apexChassisRedundancyQamMismatchStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.9 | INTEGER | read-only | This parameter indicates whether the QAM configuration of the apexes in Chassis Redundancy pair match. Both the APEXs will report the following values: These are based on its knowledge about the secondary APEX QAM configuration from heartbeat messages. unknown (0): QAM configuration of pair APEX is not known (heartbeat not received). match (1): QAM configuration of APEXs in redundancy pair match. mismatch (2): QAM configuration of APEXs in redundancy pair do not match. |
| IP apexChassisRedundancyRedundantApexIp | 1.3.6.1.4.1.1166.1.31.22.1.1.5 | IpAddress | read-write | Unicast IP address of redundant APEX. This IP address is used to send heartbeat messages to the redundant IP. This IP address should match with the ENET1 or ENET2 IP address of the redundant APEX. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexChassisRedundancyRedundantApexSecIp | 1.3.6.1.4.1.1166.1.31.22.1.1.18 | IpAddress | read-write | Unicast IP address of redundant APEX heartbeat backup interface. This IP address is used to send backup heartbeat messages to the redundant IP. This IP address should match with the ENET1 or ENET2 IP address of the redundant APEX. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexChassisRedundancyRedundantHBEnable | 1.3.6.1.4.1.1166.1.31.22.1.1.19 | EnableDisableTYPE | read-write | This parameter is set to ENABLED to configure backup heartbeat interface IP. Heartbeat message in the Backup heartbeat interface is used if the Primary heartbeat inteface fails. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexChassisRedundancySecondaryApexStatus | 1.3.6.1.4.1.1166.1.31.22.2.1.2 | INTEGER | read-only | This parameter is applicable for an APEX where chassis redundancy is enabled. The APEX configured as primary will report the following values: These are based on its knowledge about the secondary APEX from heartbeat messages. unknown(0): State of secondary is not known (heartbeat not received). active(1): Secondary RF outputs are active. standby(2): Secondary RF outputs are muted. Waiting to become active. fault(3): Secondary has experienced a fault. suspend(4): Secondary is suspended. The APEX configured as secondary will report the following values: active(1): Secondary RF outputs are active. standby(2): Secondary RF outputs are muted. Waiting to become active. fault(3): Secondary has experienced a fault. suspend(4): Secondary is suspended. |
| INT apexChassisRedundancyState | 1.3.6.1.4.1.1166.1.31.22.2.1.3 | INTEGER | read-only | This parameter is applicable for an APEX where chassis redundancy is enabled. This parameter will report the chassis redundancy availability status. These are based on its knowledge about the secondary APEX from heartbeat messages. The APEX configured as primary will report the following values: unknown(0): State of redundancy is not known (heartbeat not received). available(1): Primary is active and secondary is in standby, configurations are synchronized and no critical faults on either of the APEX. protected(2): Primary is fault and secondary is in active. unavailable(3): Configuration not synchronized or primary has not received heartbeat message from secondary. synchronizing(4): Synchronizing configuration between active and standby APEX's. The APEX configured as secondary will report the following values: unknown(0): State of redundancy is not known (heartbeat not received). available(1): Secondary is active and primary is in standby, configurations are synchronized and no critical faults on either of the APEX. protected(2): Secondary is in active and primary is fault state. unavailable(3): Configuration not synchronized or secondary is in fault state or secondary has not received heartbeat message from primary. synchronizing(4): Synchronizing configuration between active and standby APEX's. |
| apexChassisRedundancyStatus | 1.3.6.1.4.1.1166.1.31.22.2 | |||
| apexChassisRedundancyStatusGeneral | 1.3.6.1.4.1.1166.1.31.22.2.1 | |||
| STR apexChassisRedundancyStatusInvalidApplyText | 1.3.6.1.4.1.1166.1.31.22.2.1.6 | DisplayString | read-only | When apexChassisRedundancyConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. |
| ENA apexChassisRedundancySuspend | 1.3.6.1.4.1.1166.1.31.22.1.1.6 | EnableDisableTYPE | read-write | When set to enabled(2), this results in APEX unit failover and become active if it is in standby or suspend state. If the condition above is not met, setting the value to enabled(2) has no effect. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexChassisRedundancyUdpPort | 1.3.6.1.4.1.1166.1.31.22.1.1.4 | Integer32 | read-write | This UDP port number value is used as: (1) The port number on which to receive heartbeat messages from the redundant APEX (2) The port number to which heartbeat messages are sent to the redundant APEX. Valid range of UDP port numbers are 1024 to 65535. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| CLE apexClearInvalidInitData | 1.3.6.1.4.1.1166.1.31.102.2.8001 | ClearAlarmTYPE | read-write | Setting to 'clearAlarm' clears the apexAlarmInvalidInitData. The APEX will set this parameter back to 'clearAlarmNotInProgress' after clearing the alarm. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| apexConfAlarmClear | 1.3.6.1.4.1.1166.1.31.102.2 | |||
| apexConfAlarmEnable | 1.3.6.1.4.1.1166.1.31.102.1 | |||
| apexConfigAlarms | 1.3.6.1.4.1.1166.1.31.102 | |||
| APP apexCteApplyChange | 1.3.6.1.4.1.1166.1.31.20.1.2.6 | ApplyDataToDeviceTYPE | read-write | The Apply for CTE configuration items. This parameter MUST be set to 'apply' in order for any of the following to take effect: apexCteEncryptionMode apexCteCciLevel apexCteApsLevel apexCteCitEnable apexCteCommonTier This parameter MUST be set LAST after all associated parameters has been configured. @Config(config=no, reboot=no) |
| INT apexCteApsLevel | 1.3.6.1.4.1.1166.1.31.20.1.2.3 | INTEGER | read-write | Analog Protection System (APS) Level setting for PRK messages. Defines what copy protection encoding will be applied to the analog composite output by the settop box. - notDefined - analog protection is not defined, settop box applications can configure APS - off - no analog protection - splitBurstOff - AGC on, split burst off - splitBurst2Line - AGC on, 2 line split burst on - splitBurst4Line - AGC on, 4 line split burst on The APEX will set Tier Type based on apexCteApsLevel. The APEX will set tier type to subscription with right to tape when apexCteApsLevel is 'off' or 'notDefined'. The APEX will set tier type to subscription without right to tape when apexCteApsLevel is 'splitBurstOff', 'splitBurst2Line', or 'splitBurst4Line'. Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexCteCciLevel | 1.3.6.1.4.1.1166.1.31.20.1.2.2 | INTEGER | read-write | Copy Control Information (CCI) Level setting for PRK messages. - notDefined - CCI is not defined, settop box applications can configure CCI - copyFreely - program can be copied - copyOnce - program can be copied once - copyNever - program can never be copied - noMoreCopies - Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexCteCitEnable | 1.3.6.1.4.1.1166.1.31.20.1.2.4 | EnableDisableTYPE | read-write | Constrained Image Trigger (CIT) setting. If set to 'enabled' the settop box is notified not to allow a high quality digital output unless the receiving device also adheres to CIT processing. If the apexCteApsLevel is set to 'notDefined', the setting of the CIT value has no affect (CIT and APS are only used when APS is set to a defined value). Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexCteCommonTier | 1.3.6.1.4.1.1166.1.31.20.1.2.5 | Integer32 | read-write | EncryptionCommon Tier. Identifies the tier number for which access is granted. Range is 0 to 16777215. 65535 is reserved and cannot be used. The APEX will set Tier Type based on apexCteApsLevel setting. Refer to the apexCteApsLevel description for more details. Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexCteConfig | 1.3.6.1.4.1.1166.1.31.20.1.2 | |||
| INT apexCteEncryptionMode | 1.3.6.1.4.1.1166.1.31.20.1.2.1 | INTEGER | read-write | This parameter is used to set the Encryption Mode. It applies to all services on all QAMs in CTE mode. - 'full' - The APEX will use Full encryption. The APEX will only be able to encrypt programs in Full encryption mode if the APEX is able to communicate with an RDS. - 'fwk' - The APEX will use Fixed Working Key (FWK) encryption. - 'fpk' - The APEX will use Fixed Program Key (FPK) encryption. The APEX will not attempt to get EMMs. - 'clear' - The APEX performs no encryption of output programs. If the APEX is unable to encrypt programs in the configured mode, then those programs will not be mapped. Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexDataIp | 1.3.6.1.4.1.1166.1.31.6.4 | |||
| IP apexDataIpAddr | 1.3.6.1.4.1.1166.1.31.6.4.1.1.1 | IpAddress | read-write | This is the IP address of the Data IP (Enet2) interface of this APEX. The data IP address may directly be changed by setting this parameter. The Data IP address must be configured such that the Data IP interface and the OAMP interface are on different networks. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexDataIpAddrInUse | 1.3.6.1.4.1.1166.1.31.6.4.2.1.5 | IpAddress | read-only | Indicates the IP Address currently being used by the Data IP port (Enet2). This parameter will be either apexDataIpAddr or an APEX selected IP address. Refer to apexDataIpInUseReason for more information. |
| ENA apexDataIpAutoNegotiate | 1.3.6.1.4.1.1166.1.31.6.4.1.1.3 | EnableDisableTYPE | read-write | Data IP (Enet2) Ethernet Auto-Negotiation setting. 'disabled' is not supported. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexDataIpConfig | 1.3.6.1.4.1.1166.1.31.6.4.1 | |||
| apexDataIpConfigGeneral | 1.3.6.1.4.1.1166.1.31.6.4.1.1 | |||
| INT apexDataIpDuplexMode | 1.3.6.1.4.1.1166.1.31.6.4.2.1.3 | INTEGER | read-only | Data IP (Enet2) Ethernet Duplex Mode (full or half) This is determined by the results of the auto-negotiation process. If auto-negotiation fails, the default mode is Full. This status item is only valid when the Data IP port is enabled and properly configured. |
| I32 apexDataIpInputTsAssignedCount | 1.3.6.1.4.1.1166.1.31.6.4.2.1.4 | Integer32 | read-only | Number of input transport streams assigned to the Data IP interface. |
| INT apexDataIpInUseReason | 1.3.6.1.4.1.1166.1.31.6.4.2.1.7 | INTEGER | read-only | Reason for apexDataIpAddrInUse and apexDataIpSubnetMaskInUse Data IP (Enet2) parameters. 'notApplicable' - Enet2 not configured by user or for REM connection. 'userConfig' - APEX is not overriding user configured parameters. 'directRemConnection' - The DATA IP port (Enet2) is in use for QAM RF Redundancy so the APEX has overridden the user configured parameters. |
| ACT apexDataIpLinkActive | 1.3.6.1.4.1.1166.1.31.6.4.2.1.8 | ActiveTYPE | read-only | This indicates if the DataIP (ENET2) link is active. |
| STR apexDataIpMacAddr | 1.3.6.1.4.1.1166.1.31.6.4.2.1.1 | DisplayString | read-only | This is the MAC address of the APEX Data IP (Enet2) Interface. It is set at the factory and cannot be changed. The string length is 17 characters in the format 'hh:hh:hh:hh:hh:hh' where 'hh' is a hexadecimal number. |
| INT apexDataIpSpeed | 1.3.6.1.4.1.1166.1.31.6.4.2.1.2 | INTEGER | read-only | Data IP (Enet2) Ethernet speed (10Mbps or 100Mbps). This is determined by the results of the auto-negotiation process. If auto-negotiation fails, the default speed is 100Mbps. This status item is only valid when the Data IP port is enabled and properly configured. |
| apexDataIpStatus | 1.3.6.1.4.1.1166.1.31.6.4.2 | |||
| apexDataIpStatusGeneral | 1.3.6.1.4.1.1166.1.31.6.4.2.1 | |||
| IP apexDataIpSubnetMask | 1.3.6.1.4.1.1166.1.31.6.4.1.1.2 | IpAddress | read-write | This is subnet mask of the Data IP (Enet2) interface of this APEX. The data IP Subnet Mask may directly be changed by setting this parameter. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexDataIpSubnetMaskInUse | 1.3.6.1.4.1.1166.1.31.6.4.2.1.6 | IpAddress | read-only | Indicates the Subnet Mask currently being used by the Data IP port (Enet2). This parameter will be either apexDataIpSubnetMask or an APEX selected mask. Refer to apexDataIpInUseReason for more information. |
| apexDebug | 1.3.6.1.4.1.1166.1.31.5000 | |||
| apexDepi | 1.3.6.1.4.1.1166.1.31.24 | |||
| apexDepiConfig | 1.3.6.1.4.1.1166.1.31.24.1 | |||
| apexDepiConfigGeneral | 1.3.6.1.4.1.1166.1.31.24.1.1 | |||
| STR apexDepiConfigHostname | 1.3.6.1.4.1.1166.1.31.24.1.1.1 | DisplayString | read-write | Host name defined as the FQDM of the APEX-EQAM device. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2, default=yes) @File(config.ini, type='ini') |
| apexDepiControl | 1.3.6.1.4.1.1166.1.31.24.3 | |||
| apexDepiControlConfig | 1.3.6.1.4.1.1166.1.31.24.3.1 | |||
| APP apexDepiControlConfigApplyChange | 1.3.6.1.4.1.1166.1.31.24.3.1.2.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for any entries in the apexDepiControlConfigTable. Entries in the apexDepiControlConfigTable cannot be modified while DEPI Control Connections and DEPI Sessions currently exist. This parameter MUST be set to 'apply' in order for any of the data in the apexDepiControlConfigTable to take effect. This parameter MUST be set LAST after all other data in the group has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| apexDepiControlConfigApplyEntry | 1.3.6.1.4.1.1166.1.31.24.3.1.2.1 | not-accessible | DEPI Control Configuration Apply Table Entry. | |
| I32 apexDepiControlConfigApplyIndex | 1.3.6.1.4.1.1166.1.31.24.3.1.2.1.1 | Integer32 | not-accessible | The index of the Depi Control Config Apply Table. |
| apexDepiControlConfigApplyTable | 1.3.6.1.4.1.1166.1.31.24.3.1.2 | not-accessible | Table of Apply Change for the data for apexDepiControlConfigTable. Entries in the apexDepiControlConfigTable cannot be modified while DEPI Control Connections and DEPI Sessions currently exist. | |
| ENA apexDepiControlConfigEnable | 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.2 | EnableDisableTYPE | read-write | The enable setting for DEPI Control Connection. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| apexDepiControlConfigEntry | 1.3.6.1.4.1.1166.1.31.24.3.1.3.1 | not-accessible | DEPI Control Configuration Table Entry. | |
| apexDepiControlConfigGeneral | 1.3.6.1.4.1.1166.1.31.24.3.1.1 | |||
| I32 apexDepiControlConfigGeneralKeepaliveTimeout | 1.3.6.1.4.1.1166.1.31.24.3.1.1.1 | Integer32 | read-write | Timeout in seconds to wait while no control or data messages are received within the connection before sending a DEPI:HELLO message. Default is 60 seconds. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexDepiControlConfigIndex | 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.1 | Integer32 | not-accessible | The index of the Depi Control Config Table. |
| I32 apexDepiControlConfigInterfaceNumber | 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.3 | Integer32 | read-write | Represents the Gigabit Ethernet interface number. Range: '0' = Not Applicable GBE = 1-4 |
| INT apexDepiControlConfigOverUdp | 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.5 | INTEGER | read-write | This parameter indicates whether the DEPI Control Connection and Sessions will be accepted over the UDP protocol. |
| IP apexDepiControlConfigSrcIpAddr | 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.4 | IpAddress | read-write | This parameter indicates the M-CMTS Core IP address. |
| apexDepiControlConfigTable | 1.3.6.1.4.1.1166.1.31.24.3.1.3 | not-accessible | This table provides a list of DEPI Control Connections initiated by M-CMTS Cores. A maximum of 10 connections is accepted. Entries in the apexDepiControlConfigTable cannot be modified while DEPI Control Connections and DEPI Sessions currently exist. @Config(config=yes, reboot=no) @Commit(param=apexDepiControlConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| INT apexDepiControlConfigType | 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.6 | INTEGER | read-write | This parameter indicates whether DEPI Sessions are established dynamically using the DEPI control protocol or statically. Not supported. |
| apexDepiControlStatus | 1.3.6.1.4.1.1166.1.31.24.3.2 | |||
| INT apexDepiControlStatusConnectionStatus | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.4 | INTEGER | read-only | M-CMTS core to the EQAM control connection status |
| U32 apexDepiControlStatusCurrentSessions | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.12 | Unsigned32 | read-only | Number of session currently established on this control connection. Only valid for dynamically established connections. |
| apexDepiControlStatusEntry | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1 | not-accessible | DEPI Control Status Table Entry. | |
| apexDepiControlStatusGeneral | 1.3.6.1.4.1.1166.1.31.24.3.2.1 | |||
| I32 apexDepiControlStatusGeneralCurrentConnections | 1.3.6.1.4.1.1166.1.31.24.3.2.1.2 | Integer32 | read-only | The current number of DEPI Control Connections currently connected. |
| STR apexDepiControlStatusGeneralInvalidApplyText | 1.3.6.1.4.1.1166.1.31.24.3.2.1.6 | DisplayString | read-only | When apexDepiControlConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid. |
| I32 apexDepiControlStatusGeneralRejectedConnections | 1.3.6.1.4.1.1166.1.31.24.3.2.1.3 | Integer32 | read-only | The number of control connection requests rejected for any reason. |
| I32 apexDepiControlStatusGeneralTotalConnections | 1.3.6.1.4.1.1166.1.31.24.3.2.1.1 | Integer32 | read-only | The number of DEPI Control Connections established since reboot. |
| I32 apexDepiControlStatusGeneralUnknownConnectionMessages | 1.3.6.1.4.1.1166.1.31.24.3.2.1.4 | Integer32 | read-only | The number of DEPI control messages ignored not related to any existing control connection i.e. unrecognized connection identifier. |
| I32 apexDepiControlStatusGeneralUnknownSessionMessages | 1.3.6.1.4.1.1166.1.31.24.3.2.1.5 | Integer32 | read-only | The number of DEPI messages ignored not related to any existing session i.e. unrecognized session identifier. |
| U32 apexDepiControlStatusHbitSet | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.10 | Unsigned32 | read-only | Number of messages received on this control connection with H-bit set to 1. |
| I32 apexDepiControlStatusIndex | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.1 | Integer32 | not-accessible | DEPI Session ID |
| U32 apexDepiControlStatusInvalidVendorId | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.9 | Unsigned32 | read-only | Number of messages with an unsupported Vendor ID received on this control connection. The supported vendor IDs are 0 or 4491. |
| I32 apexDepiControlStatusLocalUdp | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.2 | Integer32 | read-only | The EQAM UDP port used in DEPI session messages from M-CMTS core. Only valid for DEPI connections using L2TPv3/UDP/IP. |
| U32 apexDepiControlStatusMalformedAvp | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.8 | Unsigned32 | read-only | Number of messages received on this control connection with malformed AVP. |
| U32 apexDepiControlStatusMalformedCtl | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.6 | Unsigned32 | read-only | Number of malformed DEPI messages received on this control connection. |
| U32 apexDepiControlStatusRejectedSessions | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.13 | Unsigned32 | read-only | Number of session setup related (ICQR/ICCN) messages rejected on this control connection. |
| I32 apexDepiControlStatusRemoteUdp | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.3 | Integer32 | read-only | The M-CMTS UDP port used in DEPI session messages from M-CMTS core. Only valid for DEPI connections using L2TPv3/UDP/IP. |
| apexDepiControlStatusTable | 1.3.6.1.4.1.1166.1.31.24.3.2.2 | not-accessible | Table of read-only status information pertaining to the DEPI Control Connections. | |
| U32 apexDepiControlStatusTotalSessions | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.11 | Unsigned32 | read-only | Total number of sessions established on this control connection since EQAM reboot. Only valid for dynamically established connections. |
| U32 apexDepiControlStatusUnknownAvp | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.7 | Unsigned32 | read-only | Number of messages received on this control connection with an unsupported AVP. |
| U32 apexDepiControlStatusUnknownCtl | 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.5 | Unsigned32 | read-only | Number of unrecognized DEPI messages not marked as mandatory received on this control connection. |
| apexDepiSession | 1.3.6.1.4.1.1166.1.31.24.4 | |||
| apexDepiSessionConfig | 1.3.6.1.4.1.1166.1.31.24.4.1 | |||
| APP apexDepiSessionConfigApplyChange | 1.3.6.1.4.1.1166.1.31.24.4.1.1.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for any entries in the apexDepiSessionConfigTable. This parameter MUST be set to 'apply' in order for any of the data in the apexDepiSessionConfigTable to take effect. This parameter MUST be set LAST after all other data in the table entry has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| apexDepiSessionConfigApplyEntry | 1.3.6.1.4.1.1166.1.31.24.4.1.1.1 | not-accessible | DEPI Session Status Table Entry. | |
| I32 apexDepiSessionConfigApplyOutputTsNum | 1.3.6.1.4.1.1166.1.31.24.4.1.1.1.1 | Integer32 | not-accessible | The index of the Depi Session Config Apply Table. |
| apexDepiSessionConfigApplyTable | 1.3.6.1.4.1.1166.1.31.24.4.1.1 | not-accessible | Table of Apply Change for the data for apexDepiSessionConfigTable. | |
| I32 apexDepiSessionConfigControlId | 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.3 | Integer32 | read-write | DOCSIS Control ID assignment. Value of 0 indicates transport stream to be used for Video only. |
| I32 apexDepiSessionConfigDocsisTsid | 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.4 | Integer32 | read-write | The system wide unique M-CMTS TSID mapped to the QAM. This TSID is specified by the remote ID from the ICRQ message. |
| ENA apexDepiSessionConfigEnable | 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.2 | EnableDisableTYPE | read-write | The enable setting for DEPI Session. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| apexDepiSessionConfigEntry | 1.3.6.1.4.1.1166.1.31.24.4.1.2.1 | not-accessible | DEPI Session Config Table Entry. | |
| I32 apexDepiSessionConfigOutputTsNum | 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.1 | Integer32 | not-accessible | The QAM output transport stream number which to associate the DEPI Session. |
| ENA apexDepiSessionConfigSyncCorrection | 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.6 | EnableDisableTYPE | read-write | Enable or disable updating the timestamp in the SYNC messages. This is only valid for static connections. (For dynamically established sessions, M-CMTS core enables or disables the SYNC correction during session establishment) |
| apexDepiSessionConfigTable | 1.3.6.1.4.1.1166.1.31.24.4.1.2 | not-accessible | Table of data for DEPI Session Mapping. There are 48 rows in this table mapping QAM output TS to DEPI Session. Once written, the change to this table will only take immediate effect after apexDepiSessionConfigApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexDepiSessionConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| I32 apexDepiSessionConfigUdpPort | 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.5 | Integer32 | read-write | UDP port number defining the DEPI Session (if UDP is enabled.) The range of valid port numbers is 1 to 65535. |
| apexDepiSessionStatus | 1.3.6.1.4.1.1166.1.31.24.4.2 | |||
| I32 apexDepiSessionStatusControlId | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.2 | Integer32 | read-only | The DEPI Control ID this session belongs to. |
| U32 apexDepiSessionStatusEgressDlmMsgs | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.17 | Unsigned32 | read-only | Number of DLM messages sent on this session. |
| apexDepiSessionStatusEntry | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1 | not-accessible | DEPI Session Status Table Entry. | |
| apexDepiSessionStatusGeneral | 1.3.6.1.4.1.1166.1.31.24.4.2.1 | |||
| STR apexDepiSessionStatusGeneralInvalidApplyText | 1.3.6.1.4.1.1166.1.31.24.4.2.1.1 | DisplayString | read-only | When apexDepiSessionConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid. |
| U32 apexDepiSessionStatusHbitSet | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.13 | Unsigned32 | read-only | Number of messages received on this session with H-bit set to 1. |
| U32 apexDepiSessionStatusInDataPacketDiscards | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.22 | Unsigned32 | read-only | Number of data packets received on this session that are discarded for reasons other than sequencing errors. |
| U32 apexDepiSessionStatusInDataPackets | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.20 | Unsigned32 | read-only | Number of data packets received on this session. |
| I32 apexDepiSessionStatusIndex | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.1 | Integer32 | not-accessible | DEPI Session ID. |
| U32 apexDepiSessionStatusIngressDlmMsgs | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.16 | Unsigned32 | read-only | Number of DLM messages received on this session. |
| U32 apexDepiSessionStatusInSequenceDiscards | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.21 | Unsigned32 | read-only | Number of data packets received on this session that are discarded due to sequencing error. |
| U32 apexDepiSessionStatusInSLIMsgs | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.14 | Unsigned32 | read-only | Number of SLI messages received on this session. |
| U32 apexDepiSessionStatusInvalidVendorId | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.12 | Unsigned32 | read-only | Number of messages with an unsupported Vendor ID received on this session. The supported vendor IDs are 0 or 4491. |
| U32 apexDepiSessionStatusLatencyEnd | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.19 | Unsigned32 | read-only | Last latency related timestamp end value received. |
| U32 apexDepiSessionStatusLatencyStart | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.18 | Unsigned32 | read-only | Last latency related timestamp start value received. |
| I32 apexDepiSessionStatusLocalUdp | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.4 | Integer32 | read-only | The local UDP port used by the APEX to communicate the DEPI Session messages to the M-CMTS Core |
| U32 apexDepiSessionStatusMalformedAvp | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.11 | Unsigned32 | read-only | Number of messages received on this session with malformed AVP. |
| U32 apexDepiSessionStatusMalformedCtl | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.9 | Unsigned32 | read-only | Number of malformed DEPI messages received on this session. |
| I32 apexDepiSessionStatusOutputQAMChannel | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.3 | Integer32 | read-only | The QAM Channel number this session is mapped to. |
| U32 apexDepiSessionStatusOutSLIMsgs | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.15 | Unsigned32 | read-only | Number of SLI messages sent on this session. |
| I32 apexDepiSessionStatusPerHopBehavior | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.7 | Integer32 | read-only | Per Hop Behavior value for this session. |
| I32 apexDepiSessionStatusRemoteUdp | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.5 | Integer32 | read-only | The remote UDP port used by the M-CMTS Core to communicate the DEPI Session messages to the Apex. |
| U32 apexDepiSessionStatusSessionID | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.23 | Unsigned32 | read-only | Remote DEPI Session ID, used by the Remote End to identify the DEPI Session and locally to bind the Session to a QAM Channel. |
| INT apexDepiSessionStatusStatus | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.6 | INTEGER | read-only | M-CMTS core to the EQAM control connection status |
| apexDepiSessionStatusTable | 1.3.6.1.4.1.1166.1.31.24.4.2.2 | not-accessible | Table of read-only status information pertaining to the DEPI Sessions. | |
| U32 apexDepiSessionStatusUnknownAvp | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.10 | Unsigned32 | read-only | Number of messages received on this session with an unsupported AVP. |
| U32 apexDepiSessionStatusUnknownCtl | 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.8 | Unsigned32 | read-only | Number of unrecognized DEPI messages not marked as mandatory received on this session. |
| apexDepiStatus | 1.3.6.1.4.1.1166.1.31.24.2 | |||
| apexDepiStatusGeneral | 1.3.6.1.4.1.1166.1.31.24.2.1 | |||
| I32 apexDepiStatusGeneralDtiClientPhaseError | 1.3.6.1.4.1.1166.1.31.24.2.1.4 | Integer32 | read-only | 24-bit Phase Error in units of 149.8 MHz sample clock cycles. The lower eight bits of the 24-bit field MUST be padded with zeros and MUST NOT be used by the DTI server. The value MUST be a signed 2's complement number. If the DTI client supports more bits of resolution, the DTI client MUST round the reported value to the nearest integer sample clock cycle. |
| INT apexDepiStatusGeneralDtiClientStatusMode | 1.3.6.1.4.1.1166.1.31.24.2.1.3 | INTEGER | read-only | The DTI Client MUST support and report these operational modes. |
| U32 apexDepiStatusGeneralDtiCurrentTimestamp | 1.3.6.1.4.1.1166.1.31.24.2.1.5 | Unsigned32 | read-only | DOCSIS 32-bit timestamp (DTS). |
| I32 apexDepiStatusGeneralDtiPort1CableAdvanceValue | 1.3.6.1.4.1.1166.1.31.24.2.1.6 | Integer32 | read-only | 24-bit Cable Advance value is derived by dividing the cable delay by 2. |
| ACT apexDepiStatusGeneralDtiPort1LinkActive | 1.3.6.1.4.1.1166.1.31.24.2.1.1 | ActiveTYPE | read-only | This indicates if the DTI Ethernet link is active. |
| I32 apexDepiStatusGeneralDtiPort2CableAdvanceValue | 1.3.6.1.4.1.1166.1.31.24.2.1.7 | Integer32 | read-only | 24-bit Cable Advance value is derived by dividing the cable delay by 2. |
| ACT apexDepiStatusGeneralDtiPort2LinkActive | 1.3.6.1.4.1.1166.1.31.24.2.1.2 | ActiveTYPE | read-only | This indicates if the second DTI Ethernet link is active. |
| STR apexDpmVersion | 1.3.6.1.4.1.1166.1.31.1.2.2.12 | DisplayString | read-only | APEX DPM Version. |
| apexDta | 1.3.6.1.4.1.1166.1.31.23 | |||
| apexDtaConfig | 1.3.6.1.4.1.1166.1.31.23.1 | |||
| APP apexDtaConfigApplyChange | 1.3.6.1.4.1.1166.1.31.23.1.2.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for a row of data in apexDtaRfPortConfigTable. The Apply for eight rows of data in apexDtaOtsConfigTable. A row in this table corresponds to the same row index in the apexDtaRfPortConfigTable. A row in this table corresponds to eight rows in the apexDtaOtsConfigTable when QAM module is type of either 2x4 or 2x8 as follows: Apply Table DTA OTS/QAM Config Table ----------- ----------------- 1 1-8 2 9-16 3 17-24 4 25-32 5 33-40 6 41-48 A row in this table corresponds to four rows in the apexDtaOtsConfigTable when QAM module is type of 4x4 as follows: Apply Table DTA OTS/QAM Config Table ----------- ----------------- 1 1-4 2 5-8 3 17-20 4 21-24 5 33-36 6 37-40 7 9-12 8 13-16 9 25-28 10 29-32 11 41-44 12 45-48 This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no) |
| apexDtaConfigApplyEntry | 1.3.6.1.4.1.1166.1.31.23.1.2.1 | not-accessible | DTA RF Port Configuration Apply Table Entry. | |
| I32 apexDtaConfigApplyIndex | 1.3.6.1.4.1.1166.1.31.23.1.2.1.1 | Integer32 | not-accessible | Defines the size of apexDtaRfPortConfigTable. DTA NET PID can be configured for each RF port. This shall be the number of maximum number of QAM RF port. |
| apexDtaConfigApplyTable | 1.3.6.1.4.1.1166.1.31.23.1.2 | not-accessible | Apply table for the configuration tables apexDtaRfPortConfigTable and apexDtaOtsConfigTable. | |
| apexDtaGeneralConfig | 1.3.6.1.4.1.1166.1.31.23.1.1 | |||
| APP apexDtaGeneralConfigApplyChange | 1.3.6.1.4.1.1166.1.31.23.1.1.7 | ApplyDataToDeviceTYPE | read-write | The Apply for DTA Configuration parameters. This parameter MUST be set to 'apply' in order for the DTA Cat Config data to take effect. This parameter MUST be set LAST after all DTA Config parameters affected by this parameter have been configured. @Config(config=no, reboot=no) |
| NUM apexDtaGeneralConfigCatEmmPidInterface | 1.3.6.1.4.1.1166.1.31.23.1.1.5 | EthernetInterfaceTYPE | read-write | Fast Ethernet Interface to receive CAT/EMM PID stream. One of ENET1 and ENET2 interfaces are used to receive CAT/EMM PID streams. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexDtaGeneralConfigCatEmmPidMulticastIP | 1.3.6.1.4.1.1166.1.31.23.1.1.2 | IpAddress | read-write | Multicast IPv4 address on which CAT/EMM PID stream is available. An IP Address of 0.0.0.0 indicates unicast stream. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexDtaGeneralConfigCatEmmPidSourceIP | 1.3.6.1.4.1.1166.1.31.23.1.1.3 | IpAddress | read-write | Source IP address to receive CAT/EMM PID stream. This is used only if apexQamRfConfigDtaNetworkPidMulticastIP is set to a multicast address. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexDtaGeneralConfigCatEmmPidUdpPort | 1.3.6.1.4.1.1166.1.31.23.1.1.4 | Integer32 | read-write | UDP port to receive CAT/EMM PID stream. The range of valid UDP port numbers are 1024 to 65535. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexDtaGeneralConfigCatSourceType | 1.3.6.1.4.1.1166.1.31.23.1.1.1 | INTEGER | read-write | When set to internal(0), APEX generates CAT and inserts EMM pid received from DAC. When set to external(1), APEX will not generate CAT, it will receive both CAT and EMM pids from DAC and inserts EMM pid into CAT. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexDtaGeneralConfigEmmPidNum | 1.3.6.1.4.1.1166.1.31.23.1.1.6 | Integer32 | read-write | EMM PID to insert on DTA enabled OTS. The range of valid PID numbers are 0x1C00 to 0x1FFE. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| STR apexDtaGeneralConfigInvalidApplyText | 1.3.6.1.4.1.1166.1.31.23.1.1.8 | DisplayString | read-only | When apexDtaGeneralConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with DTA CAT/EMM PID Config data or NET PID Config data. |
| ENA apexDtaOtsConfigEnable | 1.3.6.1.4.1.1166.1.31.23.1.4.1.2 | EnableDisableTYPE | read-write | This is to enable/disable of inserting DTA messages on OTS. When set to disabled(1), DTA messages are not allowed to insert on OTS. When set to enabled(2), DTA messages are allowed to insert on OTS. |
| apexDtaOtsConfigEntry | 1.3.6.1.4.1.1166.1.31.23.1.4.1 | not-accessible | DTA OTS enable configuration Table Entry. | |
| I32 apexDtaOtsConfigIndex | 1.3.6.1.4.1.1166.1.31.23.1.4.1.1 | Integer32 | not-accessible | The Output Transport Stream(OTS) number. |
| apexDtaOtsConfigTable | 1.3.6.1.4.1.1166.1.31.23.1.4 | not-accessible | Table of DTA configuration items for output transport streams (OTS). Once written, the change to this table will only take immediate effect after apexDtaConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexDtaConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| apexDtaRfPortConfigEntry | 1.3.6.1.4.1.1166.1.31.23.1.3.1 | not-accessible | DTA RF port configuration Table Entry. | |
| I32 apexDtaRfPortConfigIndex | 1.3.6.1.4.1.1166.1.31.23.1.3.1.1 | Integer32 | not-accessible | The QAM RF Port number. |
| NUM apexDtaRfPortConfigNetPidInterface | 1.3.6.1.4.1.1166.1.31.23.1.3.1.5 | EthernetInterfaceTYPE | read-write | Fast Ethernet Interface to receive Network PID stream. Network PID stream can be received either ENET1 or ENET2. |
| IP apexDtaRfPortConfigNetPidMulticastIP | 1.3.6.1.4.1.1166.1.31.23.1.3.1.2 | IpAddress | read-write | Multicast IPv4 address on which Network PID stream is available. An IP Address of 0.0.0.0 indicates unicast stream. |
| I32 apexDtaRfPortConfigNetPidNum | 1.3.6.1.4.1.1166.1.31.23.1.3.1.6 | Integer32 | read-write | Network PID to insert on DTA enabled OTS. The range of valid PID numbers are 0x1C00 to 0x1FFE. |
| IP apexDtaRfPortConfigNetPidSourceIP | 1.3.6.1.4.1.1166.1.31.23.1.3.1.3 | IpAddress | read-write | Source IP address to receive Network PID stream. This is used only if apexDtaRfPortConfigNetPidMulticastIP is set to a multicast address. |
| I32 apexDtaRfPortConfigNetPidUdpPort | 1.3.6.1.4.1.1166.1.31.23.1.3.1.4 | Integer32 | read-write | UDP port number to receive Network PID stream. The range of valid port numbers are 1024 to 65535. |
| apexDtaRfPortConfigTable | 1.3.6.1.4.1.1166.1.31.23.1.3 | not-accessible | Table of DTA configuration items configurable on a RF Port basis. Once written, the change to this table will only take immediate effect after apexDtaConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexDtaConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| STR apexDtiFpgaVersion | 1.3.6.1.4.1.1166.1.31.1.2.2.10 | DisplayString | read-only | APEX DTI FPGA Version. |
| apexEas | 1.3.6.1.4.1.1166.1.31.21 | |||
| APP apexEasApplyChange | 1.3.6.1.4.1.1166.1.31.21.1.1.1 | ApplyDataToDeviceTYPE | read-write | This object is obsolete. The Apply for any entries in the apexEasConfigGeneral group. This parameter MUST be set to 'apply' in order for any of the data in the apexEasConfigGeneral group to take effect. This parameter MUST be set LAST after all other data in the group has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| apexEasConfig | 1.3.6.1.4.1.1166.1.31.21.1 | |||
| apexEasConfigGeneral | 1.3.6.1.4.1.1166.1.31.21.1.1 | |||
| IP apexEasMulticastIpAddress | 1.3.6.1.4.1.1166.1.31.21.1.1.5 | IpAddress | read-write | This object is obsolete. This parameter indicates the Multicast IP Receive address on which to receive EAS messages. If 0.0.0.0, then EAS messages will be received via singlecast only. Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexEasNumInvalRcvMsgs | 1.3.6.1.4.1.1166.1.31.21.2.1.2 | Unsigned32 | read-only | Total number of Invalid EAS messages received (invalid CRC). These messages are discarded. |
| U32 apexEasNumRcvMsgs | 1.3.6.1.4.1.1166.1.31.21.2.1.1 | Unsigned32 | read-only | Total number of EAS messages received. |
| ENA apexEasOutputEnable | 1.3.6.1.4.1.1166.1.31.21.1.2.1.2 | EnableDisableTYPE | read-write | The enable setting for EAS output on this Output Transport Stream. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| apexEasOutputEntry | 1.3.6.1.4.1.1166.1.31.21.1.2.1 | not-accessible | A row in the EAS output table. | |
| I32 apexEasOutputStreamNum | 1.3.6.1.4.1.1166.1.31.21.1.2.1.1 | Integer32 | not-accessible | The output transport stream number. |
| apexEasOutputTable | 1.3.6.1.4.1.1166.1.31.21.1.2 | not-accessible | Table of parameters for configuring EAS Output. Table is indexed by Output Transport Stream Number. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| I32 apexEasPhysInPort | 1.3.6.1.4.1.1166.1.31.21.1.1.3 | Integer32 | read-write | This object is obsolete. Number of the input, of type configured by apexEasPhysInType, from which to extract EAS messages. Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(min=0) @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexEasPhysInType | 1.3.6.1.4.1.1166.1.31.21.1.1.2 | INTEGER | read-write | This object is obsolete. Input Type of input from which to extract EAS messages. When set to 0, no EAS is received (disables EAS extraction). Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexEasRcvUdpPort | 1.3.6.1.4.1.1166.1.31.21.1.1.4 | Integer32 | read-write | This object is obsolete. This parameter indicates the UDP port on which to receive EAS messages. Range is 1024 to 65535 when apexEasPhysInType is 'fastEnet'. Range is 0 to 65535 when apexEasPhysInType is 'gbe'. Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| APP apexEasServerApplyChange | 1.3.6.1.4.1.1166.1.31.21.1.3.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for a row in the apexEasServerTable. This parameter MUST be set to 'apply' in order for any of the data in the apexEasServerTable table to take effect. This parameter MUST be set LAST after all other data in the table has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| apexEasServerApplyEntry | 1.3.6.1.4.1.1166.1.31.21.1.3.1 | not-accessible | EAS Server Configuration Apply Table Entry. | |
| I32 apexEasServerApplyNum | 1.3.6.1.4.1.1166.1.31.21.1.3.1.1 | Integer32 | not-accessible | The EAS Server number. |
| apexEasServerApplyTable | 1.3.6.1.4.1.1166.1.31.21.1.3 | not-accessible | Apply table for the apexEasServerTable. Table is indexed by RF Port number. | |
| apexEasServerEntry | 1.3.6.1.4.1.1166.1.31.21.1.4.1 | not-accessible | A row in the EAS server table. | |
| IP apexEasServerMulticastIpAddress | 1.3.6.1.4.1.1166.1.31.21.1.4.1.5 | IpAddress | read-write | This parameter indicates the Multicast IP Receive address on which to receive EAS messages. If 0.0.0.0, then EAS messages will be received via singlecast only. Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| I32 apexEasServerNum | 1.3.6.1.4.1.1166.1.31.21.1.4.1.1 | Integer32 | not-accessible | The EAS Server number. |
| I32 apexEasServerPhysInPort | 1.3.6.1.4.1.1166.1.31.21.1.4.1.3 | Integer32 | read-write | Number of the input, of type configured by apexEasServerPhysInType, from which to extract EAS messages. Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(min=0) |
| INT apexEasServerPhysInType | 1.3.6.1.4.1.1166.1.31.21.1.4.1.2 | INTEGER | read-write | Input Type of input from which to extract EAS messages. When set to 0, no EAS is received (disables EAS extraction). Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| I32 apexEasServerRcvUdpPort | 1.3.6.1.4.1.1166.1.31.21.1.4.1.4 | Integer32 | read-write | This parameter indicates the UDP port on which to receive EAS messages. Range is 1024 to 65535 when apexEasServerPhysInType is 'fastEnet'. Range is 0 to 65535 when apexEasServerPhysInType is 'gbe'. Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| IP apexEasServerSourceIpAddress | 1.3.6.1.4.1.1166.1.31.21.1.4.1.6 | IpAddress | read-write | This parameter indicates the Source IP Receive address on which to receive EAS messages. This is only for IGMP v3 networks. If 0.0.0.0, then source IP is not used. Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| apexEasServerTable | 1.3.6.1.4.1.1166.1.31.21.1.4 | not-accessible | Table of parameters for configuring EAS Servers. Table is indexed by RF Port number. @Config(config=yes, reboot=no) @Commit(param=apexEasServerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| IP apexEasSourceIpAddress | 1.3.6.1.4.1.1166.1.31.21.1.1.6 | IpAddress | read-write | This object is obsolete. This parameter indicates the Source IP Receive address on which to receive EAS messages. This is only for IGMP v3 networks. If 0.0.0.0, then source IP is not used. Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexEasStatus | 1.3.6.1.4.1.1166.1.31.21.2 | |||
| apexEasStatusGeneral | 1.3.6.1.4.1.1166.1.31.21.2.1 | |||
| I32 apexEcmEmmFirstPid | 1.3.6.1.4.1.1166.1.31.15.1.1.7 | Integer32 | read-write | First ECM-EMM PID when PID Remapping is disabled on an output stream. This PID along with the apexEcmEmmNumberPids defines a range of PIDs that the APEX will use for all ECMs and EMMs. These configuration settings allow a user to select a range that other service and ancillary PIDs will not use. This allows the APEX to use PIDs for ECMs and EMMs without having PID collisions. PID collisions will cause the APEX to select another ECM or EMM PID causing momentary glitches of the output video and audio. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexEcmEmmNumberPids | 1.3.6.1.4.1.1166.1.31.15.1.1.8 | Integer32 | read-write | Number of ECM-EMM PIDs to use when PID Remapping is disabled on an output stream. Refer to the apexEcmEmmFirstPid parameter for a complete description. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableChassisRedundancyAvailabilityFault | 1.3.6.1.4.1.1166.1.31.102.1.8092 | EnableDisableTYPE | read-write | This setting enables or disables apexEnableChassisRedundancyAvailabilityFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableChassisRedundancyConfigurationFault | 1.3.6.1.4.1.1166.1.31.102.1.8094 | EnableDisableTYPE | read-write | This setting enables or disables apexEnableChassisRedundancyConfigurationFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableChassisRedundancyLinkFault | 1.3.6.1.4.1.1166.1.31.102.1.8093 | EnableDisableTYPE | read-write | This setting enables or disables apexEnableChassisRedundancyLinkFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableChassisRedundancyPrimaryFailover | 1.3.6.1.4.1.1166.1.31.102.1.8090 | EnableDisableTYPE | read-write | This setting enables or disables apexEnableChassisRedundancyPrimaryFailover. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableChassisRedundancySecondaryFailover | 1.3.6.1.4.1.1166.1.31.102.1.8091 | EnableDisableTYPE | read-write | This setting enables or disables apexEnableChassisRedundancySecondaryFailover. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableDepiControlConnectionFault | 1.3.6.1.4.1.1166.1.31.102.1.8080 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmDepiControlConnectionFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableDepiSessionSetupFault | 1.3.6.1.4.1.1166.1.31.102.1.8081 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmDepiSessionSetupFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableDtiSyncLossFault | 1.3.6.1.4.1.1166.1.31.102.1.8082 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmDtiSyncLossFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableGbeBufferFullness | 1.3.6.1.4.1.1166.1.31.102.1.8021 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmGbeBufferFullness. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableGbeInputStreamHighBitRate | 1.3.6.1.4.1.1166.1.31.102.1.8023 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmGbeInputStreamHighBitRate. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableGbeInputStreamLowBitRate | 1.3.6.1.4.1.1166.1.31.102.1.8022 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmGbeInputStreamLowBitRate. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableGbeInterfaceRedundFailOver | 1.3.6.1.4.1.1166.1.31.102.1.8029 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmGbeInterfaceRedundFailOver. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableGbeLossOfInputTsFault | 1.3.6.1.4.1.1166.1.31.102.1.8027 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmGbeLossOfInputStream. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableGbeLossOfPhysicalInput | 1.3.6.1.4.1.1166.1.31.102.1.8020 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmGbeLossOfPhysicalInput. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableGbeMptsRedundFailOver | 1.3.6.1.4.1.1166.1.31.102.1.8025 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmGbeMptsRedundFailOver. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableGbeMptsRedundPrimaryThreshold | 1.3.6.1.4.1.1166.1.31.102.1.8024 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmGbeMptsRedundPrimaryThreshold. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableInvalidInitData | 1.3.6.1.4.1.1166.1.31.102.1.8001 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmInvalidInitData. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableOutputOverflow | 1.3.6.1.4.1.1166.1.31.102.1.8041 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmOutputOverflow. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableOutputUtilizationFault | 1.3.6.1.4.1.1166.1.31.102.1.8040 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmOutputUtilizationFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableQamChannelFault | 1.3.6.1.4.1.1166.1.31.102.1.8044 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmQamChannelFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableQamModuleFault | 1.3.6.1.4.1.1166.1.31.102.1.8042 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmQamModuleFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableQamRfPortFault | 1.3.6.1.4.1.1166.1.31.102.1.8043 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmQamRfPortFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableQamRfRedundFailOver | 1.3.6.1.4.1.1166.1.31.102.1.8045 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmQamRfRedundFailOver. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableQamRfRedundMismatch | 1.3.6.1.4.1.1166.1.31.102.1.8046 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmQamRfRedundMismatch. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableRdsCommAlarmFault | 1.3.6.1.4.1.1166.1.31.102.1.8060 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmRdsCommFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableRemCommFault | 1.3.6.1.4.1.1166.1.31.102.1.8070 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmRemCommFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableRemFault | 1.3.6.1.4.1.1166.1.31.102.1.8071 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmRemFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableRtspControllerCommFault | 1.3.6.1.4.1.1166.1.31.102.1.8050 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmRtspControllerCommFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexEnableServiceInError | 1.3.6.1.4.1.1166.1.31.102.1.8026 | EnableDisableTYPE | read-write | This setting enables or disables apexAlarmServiceInError. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexEncryption | 1.3.6.1.4.1.1166.1.31.20 | |||
| INT apexEncryptionConfAlgorithm | 1.3.6.1.4.1.1166.1.31.20.1.1.1 | INTEGER | read-write | Configured encryption algorithm. This value determines which MUX FPGA image will be loaded. dvb-csa-simulcrypt must be selected to allow for configuration of Simulcrypt. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexEncryptionConfig | 1.3.6.1.4.1.1166.1.31.20.1 | |||
| apexEncryptionConfigGeneral | 1.3.6.1.4.1.1166.1.31.20.1.1 | |||
| U32 apexEncryptionCwCountsPerSecond | 1.3.6.1.4.1.1166.1.31.20.2.1.2.12.1.2 | Unsigned32 | read-only | Number of CW successfully generated on this MC2.1 per second, integrated over the last minute. |
| I32 apexEncryptionCwgPerSecond | 1.3.6.1.4.1.1166.1.31.20.2.1.2.1 | Integer32 | read-only | Average control words per second generated integrated over the last minute. |
| apexEncryptionCwgStatus | 1.3.6.1.4.1.1166.1.31.20.2.1.2 | |||
| I32 apexEncryptionEmmBadRepliesRecvd | 1.3.6.1.4.1.1166.1.31.20.2.1.2.8 | Integer32 | read-only | Counts number of triton EMM replies marked bad received from mc2.1 devices. |
| I32 apexEncryptionEmmGoodDeliveryTimeMs | 1.3.6.1.4.1.1166.1.31.20.2.1.2.9 | Integer32 | read-only | Amount of time expressed in milliseconds taken to deliver entire set of EMMs for most recent successful attempt. Note it takes MC2.1 a significant amount of time to process an EMM. They are delivered in batches of 6 (1 per MC2.1) the firmware then waits for all 6 EMM replies before continuing with the next batch. |
| I32 apexEncryptionEmmGoodRepliesRecvd | 1.3.6.1.4.1.1166.1.31.20.2.1.2.7 | Integer32 | read-only | Counts number of triton EMM replies marked good received from mc2.1 devices. |
| I32 apexEncryptionEmmMaxDeliveryTimeMs | 1.3.6.1.4.1.1166.1.31.20.2.1.2.10 | Integer32 | read-only | Maximum amount of time expressed in milliseconds taken to deliver an entire set of EMMs since the Apex unit was last rebooted. |
| I32 apexEncryptionEmmMinDeliveryTimeMs | 1.3.6.1.4.1.1166.1.31.20.2.1.2.11 | Integer32 | read-only | Minimum amount of time expressed in milliseconds taken to deliver an entire set of EMMs since the Apex unit was last rebooted. |
| I32 apexEncryptionEmmRequestsSent | 1.3.6.1.4.1.1166.1.31.20.2.1.2.6 | Integer32 | read-only | Counts number of triton EMM reports sent to 6 MC2.1 devices. |
| I32 apexEncryptionMcDiagDeviceIndex | 1.3.6.1.4.1.1166.1.31.20.2.1.2.12.1.1 | Integer32 | not-accessible | Index represents 1 of 6 MC2.1 devices installed on ACP Module. |
| apexEncryptionMcDiagEntry | 1.3.6.1.4.1.1166.1.31.20.2.1.2.12.1 | not-accessible | A row in the mc2.1 diagnostic table. | |
| apexEncryptionMcDiagTable | 1.3.6.1.4.1.1166.1.31.20.2.1.2.12 | not-accessible | Diagnostic table that breaks out individual mc21 performance parameters. Indexed 1-6 for the 6 MC2.1 devices in an APEX ACP Module. | |
| I32 apexEncryptionMux1CollisionCount | 1.3.6.1.4.1.1166.1.31.20.2.1.2.2 | Integer32 | read-only | Triton collision counter for MUX FPGA #1. |
| I32 apexEncryptionMux1RolloverCount | 1.3.6.1.4.1.1166.1.31.20.2.1.2.4 | Integer32 | read-only | Counts rollovers of triton message circular buffer for MUX FPGA #1. |
| I32 apexEncryptionMux2CollisionCount | 1.3.6.1.4.1.1166.1.31.20.2.1.2.3 | Integer32 | read-only | Triton collision counter for MUX FPGA #2. |
| I32 apexEncryptionMux2RolloverCount | 1.3.6.1.4.1.1166.1.31.20.2.1.2.5 | Integer32 | read-only | Counts rollovers of triton message circular buffer for MUX FPGA #2. |
| INT apexEncryptionStatAlgorithm | 1.3.6.1.4.1.1166.1.31.20.2.1.1 | INTEGER | read-only | Current encryption algorithm. This value determines which MUX FPGA image will be loaded. |
| apexEncryptionStatus | 1.3.6.1.4.1.1166.1.31.20.2 | |||
| apexEncryptionStatusGeneral | 1.3.6.1.4.1.1166.1.31.20.2.1 | |||
| U32 apexEventChassisRedunFirmwareVersionMismatch | 1.3.6.1.4.1.1166.1.31.101.8112 | Unsigned32 | read-only | Generated when the primary and secondary APEX firmware versions are mismatched. |
| U32 apexEventChassisRedunPrimaryForceFailover | 1.3.6.1.4.1.1166.1.31.101.8110 | Unsigned32 | read-only | Generated when the operator forces a failover from the primary, back to the secondary APEX. |
| U32 apexEventChassisRedunQAMVersionMismatch | 1.3.6.1.4.1.1166.1.31.101.8113 | Unsigned32 | read-only | Generated when the primary and secondary APEX QAM versions are mismatched. |
| U32 apexEventChassisRedunSecondaryForceFailover | 1.3.6.1.4.1.1166.1.31.101.8111 | Unsigned32 | read-only | Generated when the operator forces a failover from the secondary, back to the primary APEX. |
| U32 apexEventEmUserLoginFailed | 1.3.6.1.4.1.1166.1.31.101.8100 | Unsigned32 | read-only | Event to indicate APEX EM User login failed 5 times. |
| U32 apexEventQamModuleUpgraded | 1.3.6.1.4.1.1166.1.31.101.8101 | Unsigned32 | read-only | Event to indicate a QAM Module has been upgraded from 2x4 to 2x8 channel capability. |
| apexEvents | 1.3.6.1.4.1.1166.1.31.101 | |||
| I32 apexFanModuleInstalledCount | 1.3.6.1.4.1.1166.1.31.8.2.1.3 | Integer32 | read-only | Number of Fan-Only Modules currently installed in QAM Module slots. |
| apexFastEnet | 1.3.6.1.4.1.1166.1.31.6 | |||
| apexFastEnetConfig | 1.3.6.1.4.1.1166.1.31.6.1 | |||
| apexFastEnetConfigGeneral | 1.3.6.1.4.1.1166.1.31.6.1.1 | |||
| IP apexFastEnetDefaultGateway | 1.3.6.1.4.1.1166.1.31.6.1.1.1 | IpAddress | read-write | This is the IP address of the default gateway for the Fast Ethernet interfaces. This should be zero or a valid Class A, B, or C IP address. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexFastEnetInsertPacketsEntry | 1.3.6.1.4.1.1166.1.31.6.2.3.1 | not-accessible | A row in the Output Transport Stream FE Insert Packets table. | |
| apexFastEnetInsertPacketsTable | 1.3.6.1.4.1.1166.1.31.6.2.3 | not-accessible | Table of Output Transport Stream FE Insert Packet Statistics. Indexed by Output Transport Stream number. | |
| I32 apexFastEnetInsertRate | 1.3.6.1.4.1.1166.1.31.6.1.1.2.1.2 | Integer32 | read-write | Insertion Rate for the transport stream for Fast Ethernet MPEG data. Maximum MPEG data rate to insert data received via Fast Ethernet interfaces. Range is 0 Kbps to 2500 Kbps for each transport stream. Total for all transport streams must not exceed 10000 Kbps. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(min=0, max=2500) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexFastEnetInsertRateEntry | 1.3.6.1.4.1.1166.1.31.6.1.1.2.1 | not-accessible | Output Transport Rate of Fast Ethernet MPEG Insertion Configuration Table Entry. | |
| I32 apexFastEnetInsertRateOutputTsNum | 1.3.6.1.4.1.1166.1.31.6.1.1.2.1.1 | Integer32 | not-accessible | Output Transport Stream Number. |
| apexFastEnetInsertRateTable | 1.3.6.1.4.1.1166.1.31.6.1.1.2 | not-accessible | This is a table of configuration parameters for Output Transport Rate of Fast Ethernet MPEG data Insertion. | |
| U32 apexFastEnetInsPacketsNumDiscarded | 1.3.6.1.4.1.1166.1.31.6.2.3.1.4 | Unsigned32 | read-only | Number of MPEG packets discarded during the last monitoring period (currently 5 seconds) on this Output Transport Stream. This may be due to a buffer overflow or incorrect configuration of the FE output stream insertion rate. |
| U32 apexFastEnetInsPacketsNumPkts | 1.3.6.1.4.1.1166.1.31.6.2.3.1.2 | Unsigned32 | read-only | Number of MPEG packets inserted during the last monitoring period (currently 5 seconds) on this Output Transport Stream. |
| I32 apexFastEnetInsPacketsOutputTsNum | 1.3.6.1.4.1.1166.1.31.6.2.3.1.1 | Integer32 | not-accessible | Output Transport Stream Number. |
| U32 apexFastEnetInsPacketsTotDiscarded | 1.3.6.1.4.1.1166.1.31.6.2.3.1.5 | Unsigned32 | read-only | Total number of FE MPEG packets discarded on this Output Transport Stream. Discarded packets on an output stream are those packets discarded due to an overflow condition. |
| U32 apexFastEnetInsPacketsTotPkts | 1.3.6.1.4.1.1166.1.31.6.2.3.1.3 | Unsigned32 | read-only | Total number of MPEG packets inserted on this Output Transport Stream. |
| I32 apexFastEnetMaxInputUdpPorts | 1.3.6.1.4.1.1166.1.31.6.2.1.1 | Integer32 | read-only | Maximum number of Fast Ethernet input UDP ports that can be opened on this APEX. |
| U32 apexFastEnetPacketsNumDiscarded | 1.3.6.1.4.1.1166.1.31.6.2.2.1.4 | Unsigned32 | read-only | Number of MPEG packets discarded during the last monitoring period (currently 5 seconds) on this FE interface port. This may be due to a buffer overflow or incorrect configuration of the FE output stream insertion rate. |
| U32 apexFastEnetPacketsNumPkts | 1.3.6.1.4.1.1166.1.31.6.2.2.1.2 | Unsigned32 | read-only | Number of MPEG packets inserted during the last monitoring period (currently 5 seconds) on this FE interface port. |
| I32 apexFastEnetPacketsPortNum | 1.3.6.1.4.1.1166.1.31.6.2.2.1.1 | Integer32 | not-accessible | Fast Ethernet interface port Number. |
| U32 apexFastEnetPacketsTotDiscarded | 1.3.6.1.4.1.1166.1.31.6.2.2.1.5 | Unsigned32 | read-only | Total number of FE MPEG packets discarded on this Output Transport Stream. Discarded packets on an FE interface port are those packets discarded due to an overflow condition. |
| U32 apexFastEnetPacketsTotPkts | 1.3.6.1.4.1.1166.1.31.6.2.2.1.3 | Unsigned32 | read-only | Total number of MPEG packets inserted on this FE interface port. |
| APP apexFastEnetRoutingApplyChange | 1.3.6.1.4.1.1166.1.31.6.1.1.3 | ApplyDataToDeviceTYPE | read-write | The Apply for the Fast Ethernet Static Routing Table. This parameter MUST be set to 'apply' in order for any of the data in the apexFastEnetRoutingTable to take effect. This parameter MUST be set LAST after all other data in the apexFastEnetRoutingTable has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| IP apexFastEnetRoutingDestinIp | 1.3.6.1.4.1.1166.1.31.6.1.2.1.2 | IpAddress | read-write | The Fast Ethernet Routing Destination IP address. Once written, the change to this parameter will only take immediate effect after apexFastEnetRoutingApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| apexFastEnetRoutingEntry | 1.3.6.1.4.1.1166.1.31.6.1.2.1 | not-accessible | Fast Ethernet Interface Configuration Static Routing Table Entry. | |
| IP apexFastEnetRoutingGatewayIp | 1.3.6.1.4.1.1166.1.31.6.1.2.1.3 | IpAddress | read-write | The Fast Ethernet Routing Gateway IP address. Once written, the change to this parameter will only take immediate effect after apexFastEnetRoutingApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| I32 apexFastEnetRoutingIndex | 1.3.6.1.4.1.1166.1.31.6.1.2.1.1 | Integer32 | not-accessible | The index of the Routing table entry. Currently limited to 16. |
| IP apexFastEnetRoutingSubnetMask | 1.3.6.1.4.1.1166.1.31.6.1.2.1.4 | IpAddress | read-write | The Fast Ethernet Routing Subnet Mask. Once written, the change to this parameter will only take immediate effect after apexFastEnetRoutingApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. |
| apexFastEnetRoutingTable | 1.3.6.1.4.1.1166.1.31.6.1.2 | not-accessible | This table is the configuration Static Routing table for the Fast Ethernet Interface. @Commit(param=apexFastEnetRoutingApplyChange, value=2) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| apexFastEnetStatus | 1.3.6.1.4.1.1166.1.31.6.2 | |||
| apexFastEnetStatusGeneral | 1.3.6.1.4.1.1166.1.31.6.2.1 | |||
| apexFastEnetStatusPacketsEntry | 1.3.6.1.4.1.1166.1.31.6.2.2.1 | not-accessible | A row in the FE Insert Packets table. | |
| apexFastEnetStatusPacketsTable | 1.3.6.1.4.1.1166.1.31.6.2.2 | not-accessible | Table of Fast Ethernet Insert Packet Statistics for each Fast Ethernet interface. Indexed by FE interface port number. | |
| apexGbe | 1.3.6.1.4.1.1166.1.31.7 | |||
| STR apexGbeApplicationCodeVersion | 1.3.6.1.4.1.1166.1.31.7.2.1.2 | DisplayString | read-only | APEX Gigabit Ethernet Processor Application Code Version. |
| STR apexGbeBootCodeVersion | 1.3.6.1.4.1.1166.1.31.7.2.1.1 | DisplayString | read-only | APEX Gigabit Ethernet Processor Boot Code Version. |
| APP apexGbeConfIfRedundApplyChange | 1.3.6.1.4.1.1166.1.31.7.1.7.3.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the row of data in the GBE Config Interface Redundancy Table. A row in this table corresponds to the same row index in the GBE Config Interface Redundancy table. This parameter MUST be set to 'apply' in order for any of the data in the GBE Input Data Stream Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the GBE Input Data Stream Table row has been configured. @Config(config=no, reboot=no) |
| I32 apexGbeConfIfRedundApplyIndex | 1.3.6.1.4.1.1166.1.31.7.1.7.3.1.1 | Integer32 | not-accessible | The index of the GBE Config Interface Redundancy Table. |
| ENA apexGbeConfIfRedundAutoSwitchBackEnable | 1.3.6.1.4.1.1166.1.31.7.1.7.1.1 | EnableDisableTYPE | read-write | Enables the ability for the secondary interface to switch back when link is re-detected on the primary interface. Auto switch back to the primary interface will not occur if the user forced a failover to the secondary. Auto switch back only occurs after a non-forced failover. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') |
| I32 apexGbeConfIfRedundAutoSwitchBackPeriod | 1.3.6.1.4.1.1166.1.31.7.1.7.1.2 | Integer32 | read-write | Timer for determining that the primary interface is OK for auto- switchback. The primary interface must have link for the configured amount of time. Valid time is 1-30 seconds. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') |
| ENA apexGbeConfIfRedundEnable | 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.2 | EnableDisableTYPE | read-write | Enables GbE Interface Redundancy for ports pair. Failover is based on link status. If the primary GbE fails, the secondary GbE will become active and will start receiving content. There is no data rate comparison, as only one interface in the redundancy pair is active. The secondary GbE cannot be in use prior to enabling redundancy. TS redundancy may not be used at the same time as interface redundancy. Interface redundancy is not applicable when chassis redundancy is enabled. Once written, the change to this table will only take immediate effect after apexGbeConfIfRedundApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexGbeConfIfRedundApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') |
| INT apexGbeConfIfRedundForceFailover | 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.3 | INTEGER | read-write | When set to failover(2), this results in the APEX switching to the interface that is currently not in use. If the primary GbE is in use and this is set to failover(2) mappings will be then routed to the secondary GbE. If the secondary GbE is in use and this is set to failover(2) mappings will then be routed back to the primary GbE. Once written, the change to this table will take immediate @Config(config=no, reboot=no) |
| I32 apexGbeConfIfRedundIndex | 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.1 | Integer32 | not-accessible | GbE Interface Pair number. Value of 1 is GbE1 and GbE2 pair. Value of 2 is GbE3 and GbE4 pair. |
| ENA apexGbeConfIfRedundSuspendFailover | 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.4 | EnableDisableTYPE | read-write | Enables and disables suspending of Interface failover. Prevents failovers to or from backup. Force failover (apexGbeConfIfRedundForceFailover) overrides this setting. Once written, the change to this table will only take immediate effect after apexGbeConfIfRedundApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexGbeConfIfRedundApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') |
| apexGbeConfig | 1.3.6.1.4.1.1166.1.31.7.1 | |||
| ENA apexGbeConfigAutoNegotiate | 1.3.6.1.4.1.1166.1.31.7.1.2.1.5 | EnableDisableTYPE | read-write | Auto negotiation enabled or disabled. |
| ENA apexGbeConfigEnable | 1.3.6.1.4.1.1166.1.31.7.1.2.1.2 | EnableDisableTYPE | read-write | This parameter enables the Gigabit Ethernet Interface. |
| apexGbeConfigEntry | 1.3.6.1.4.1.1166.1.31.7.1.2.1 | not-accessible | Gigabit Ethernet Interface Configuration Table Entry. | |
| I32 apexGbeConfigFrameBufferAlarmThreshold | 1.3.6.1.4.1.1166.1.31.7.1.3.1.3 | Integer32 | read-write | User defined threshold representing a percentage of frame buffer depth. The frame buffer level is monitored by the APEX and the maximum level is based on the actual input data rate. The threshold percentage is used to determine when to issue a Gigabit Ethernet Frame Buffer Fullness alarm (apexAlarmGbeBufferFullness). |
| apexGbeConfigFrameBufferEntry | 1.3.6.1.4.1.1166.1.31.7.1.3.1 | not-accessible | Gigabit Ethernet Frame Buffer Configuration Table Entry. | |
| U32 apexGbeConfigFrameBufferMaxInDataRate | 1.3.6.1.4.1.1166.1.31.7.1.3.1.2 | Unsigned32 | read-write | Maximum Gigabit Ethernet MPEG input data rate in bps. This is the total amount of MPEG data expected to be received by Gigabit Ethernet frame interfaces on the processor. This data rate is used to determine the frame buffer reset limit. The expected data rate should always be set equal to or greater than the actual input data rate. The value of apexGbeJitterAbsorption can limit the valid range of this data rate. It is highly recommended that the user consult with Motorola prior to changing the expected data rate. |
| I32 apexGbeConfigFrameBufferProcessorNum | 1.3.6.1.4.1.1166.1.31.7.1.3.1.1 | Integer32 | not-accessible | Gigabit Ethernet Processor Number. Proc 1 = GBE Interfaces 1 and 2 Proc 2 = GBE Interfaces 3 and 4 |
| apexGbeConfigFrameBufferTable | 1.3.6.1.4.1.1166.1.31.7.1.3 | not-accessible | This is a table of configuration parameters related to Gigabit Ethernet Frame Buffer statistics gathering. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| apexGbeConfigGeneral | 1.3.6.1.4.1.1166.1.31.7.1.1 | |||
| APP apexGbeConfigInputDataTsApplyChange | 1.3.6.1.4.1.1166.1.31.7.1.6.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the row of data in the GBE Input Data Stream Table. A row in this table corresponds to the same row index in the GBE Input Data Stream table. This parameter MUST be set to 'apply' in order for any of the data in the GBE Input Data Stream Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the GBE Input Data Stream Table row has been configured. @Config(config=no, reboot=no) |
| apexGbeConfigInputDataTsApplyEntry | 1.3.6.1.4.1.1166.1.31.7.1.6.1 | not-accessible | GBE Input Data Stream Apply Table Entry. | |
| I32 apexGbeConfigInputDataTsApplyIndex | 1.3.6.1.4.1.1166.1.31.7.1.6.1.1 | Integer32 | not-accessible | The index of the GBE Input Data Stream Apply Table. |
| apexGbeConfigInputDataTsApplyTable | 1.3.6.1.4.1.1166.1.31.7.1.6 | not-accessible | Table of Apply Change for the GBE Input Data Stream Table. A row in this table corresponds to the same row index in the GBE Input Data Stream table (apexGbeConfigInputDataTsTable). | |
| STR apexGbeConfigInputDataTsApplyText | 1.3.6.1.4.1.1166.1.31.7.1.1.9 | DisplayString | read-only | When apexGbeConfigInputDataTsApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid. |
| ENA apexGbeConfigInputDataTsEnable | 1.3.6.1.4.1.1166.1.31.7.1.5.1.2 | EnableDisableTYPE | read-write | Indicates whether this GBE Input Data Stream entry is enabled or disabled. |
| apexGbeConfigInputDataTsEntry | 1.3.6.1.4.1.1166.1.31.7.1.5.1 | not-accessible | GBE Input Data Stream Table Entry. | |
| I32 apexGbeConfigInputDataTsIndex | 1.3.6.1.4.1.1166.1.31.7.1.5.1.1 | Integer32 | not-accessible | Index of GBE Input Data Stream Table. |
| I32 apexGbeConfigInputDataTsInterface | 1.3.6.1.4.1.1166.1.31.7.1.5.1.3 | Integer32 | read-write | Number of the input interface (Port number). Range: '0' = Not Applicable GBE = 1-4 |
| IP apexGbeConfigInputDataTsMulticastIp | 1.3.6.1.4.1.1166.1.31.7.1.5.1.5 | IpAddress | read-write | The Multicast receive IP address. An IP address of 0.0.0.0 indicates singlecast only. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved. |
| IP apexGbeConfigInputDataTsSourceIp | 1.3.6.1.4.1.1166.1.31.7.1.5.1.6 | IpAddress | read-write | This is the IP address of the source device. This field is only used when a multicast IP address is also specified. |
| apexGbeConfigInputDataTsTable | 1.3.6.1.4.1.1166.1.31.7.1.5 | not-accessible | Table of data for GBE input data stream identification. Each entry in this table identifies a Gigabit Ethernet input stream that is a data stream only. Data streams are streams without PCR. These streams require special processing to avoid overflowing the output. There are 128 rows in this table. Once written, the change to this table will only take immediate effect after apexGbeConfigInputDataTsApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexGbeConfigInputDataTsApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') | |
| I32 apexGbeConfigInputDataTsUdp | 1.3.6.1.4.1.1166.1.31.7.1.5.1.4 | Integer32 | read-write | GBE Input UDP Port. Range: 0-65535 |
| apexGbeConfigInputRedundancy | 1.3.6.1.4.1.1166.1.31.7.1.4 | |||
| apexGbeConfigInputRedundancyGeneral | 1.3.6.1.4.1.1166.1.31.7.1.4.1 | |||
| I32 apexGbeConfigInterfaceNum | 1.3.6.1.4.1.1166.1.31.7.1.2.1.1 | Integer32 | not-accessible | Gigabit Ethernet Interface Number. |
| apexGbeConfigInterfaceRedundancy | 1.3.6.1.4.1.1166.1.31.7.1.7 | |||
| apexGbeConfigInterfaceRedundancyApplyEntry | 1.3.6.1.4.1.1166.1.31.7.1.7.3.1 | not-accessible | GBE Config Interface Redundancy Table Entry. | |
| apexGbeConfigInterfaceRedundancyApplyTable | 1.3.6.1.4.1.1166.1.31.7.1.7.3 | not-accessible | Table of Apply Change for the GBE Interface Redundancy Configuration Table. A row in this table corresponds to the same row index in the GBE Config Interface Redundancy table (apexGbeConfigInterfaceRedundancyTable). | |
| apexGbeConfigInterfaceRedundancyEntry | 1.3.6.1.4.1.1166.1.31.7.1.7.2.1 | not-accessible | GbE Interface Redundancy Configuration Table Entry. | |
| apexGbeConfigInterfaceRedundancyGeneral | 1.3.6.1.4.1.1166.1.31.7.1.7.1 | |||
| apexGbeConfigInterfaceRedundancyTable | 1.3.6.1.4.1.1166.1.31.7.1.7.2 | not-accessible | This is a table of configuration parameters for GbE Interface Redundancy. | |
| IP apexGbeConfigIpAddr | 1.3.6.1.4.1.1166.1.31.7.1.2.1.3 | IpAddress | read-write | This is the IP address of this Gigabit Ethernet interface. It is recommended that each Gigabit Ethernet interface be on a different subnet. Each must be given a unique IP address. 0.0.0.0 indicates the interface is not in use. |
| IP apexGbeConfigIpSubnetMask | 1.3.6.1.4.1.1166.1.31.7.1.2.1.4 | IpAddress | read-write | This is subnet mask of this Gigabit Ethernet interface. |
| apexGbeConfigTable | 1.3.6.1.4.1.1166.1.31.7.1.2 | not-accessible | This is a table of configuration parameters for the Gigabit Ethernet Interfaces. Once written, the change to this table will only take immediate effect after apexGbeConfigTableApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexGbeConfigTableApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| APP apexGbeConfigTableApplyChange | 1.3.6.1.4.1.1166.1.31.7.1.1.5 | ApplyDataToDeviceTYPE | read-write | The Apply for the Gigabit Ethernet Configuration Table. This parameter MUST be set to 'apply' in order for any of the data in the apexGbeConfigTable to take effect. This parameter MUST be set LAST after all other data in the apexGbeConfigTable has been configured. @Config(config=no, reboot=no) |
| I32 apexGbeConfInputMulticastTimeout | 1.3.6.1.4.1.1166.1.31.7.1.1.11 | Integer32 | read-write | Loss of input stream timeout value (in milliseconds) for multicast inputs. This determines the amount of time a unicast input stream is missing before the APEX will declare the input stream lost. Loss of input is used for determining all SDV failover conditions. It is also used for Manual Routing failover conditions when using hot/warm transport stream redundancy. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(step=200) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexGbeConfInputUnicastTimeout | 1.3.6.1.4.1.1166.1.31.7.1.1.10 | Integer32 | read-write | Loss of input stream timeout value (in milliseconds) for unicast inputs. This determines the amount of time a unicast input stream is missing before the APEX will declare the input stream lost. Loss of input is used for determining all SDV failover conditions. It is also used for Manual Routing failover conditions when using hot/warm transport stream redundancy. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(step=200) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexGbeConfInRedundAutoSwitchBack | 1.3.6.1.4.1.1166.1.31.7.1.4.1.3 | EnableDisableTYPE | read-write | This is the enable/disable of automatic switch back from Secondary to Primary for Gigabit Ethernet redundancy. When 'enabled', switch back to the Primary will automatically occur when the Primary is restored. When 'disabled', the user must force back to the Primary using apexGbeConfInRedundForceToPrimary or apexManRteGbeInRedForceSwitch. This parameter applies to all configured redundant pairs. Auto switch back to the primary will not occur if the user forced a failover to the secondary. Auto switch back only occurs after a non-forced failover event. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') |
| INT apexGbeConfInRedundForceToPrimary | 1.3.6.1.4.1.1166.1.31.7.1.4.1.5 | INTEGER | read-write | The Gigabit Ethernet Redundant Pair force switch any pair that is currently on the Secondary to the Primary. This will have no effect if the corresponding row setting of apexManRteGbeInRedEnable is 'disabled'. This will only have an effect when the Secondary is the In-Use Input TS of a Redundant Pair (apexInputTsStatPriState or apexInputTsStatSecState is 'openedInUse'). Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| INT apexGbeConfInRedundForceToSecondary | 1.3.6.1.4.1.1166.1.31.7.1.4.1.4 | INTEGER | read-write | The Gigabit Ethernet Redundant Pair force switch any pair that is currently on the Primary to the Secondary. This will have no effect if the corresponding row setting of apexManRteGbeInRedEnable is 'disabled'. This will only have an effect when the Primary is the In-Use Input TS of a Redundant Pair (apexInputTsStatPriState or apexInputTsStatSecState is 'openedInUse'). Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| INT apexGbeConfInRedundManualRouteRedundType | 1.3.6.1.4.1.1166.1.31.7.1.4.1.6 | INTEGER | read-write | The redundancy type for output streams in Manual Routing operating mode. - hotWarm indicates only 1 input stream, primary or secondary, is open at any one time. For multicast streams, primary will be joined initially. The secondary is joined after a failover (the primary will be dropped prior to joining the secondary). When falling back to the primary, the secondary is dropped (closed), then the primary is joined (opened). - hotHot indicates both the primary and secondary streams are opened at the same time. For multicast streams, both streams are joined immediately. Changes to the redundancy type cannot be made while there are active routes. All routes must be deleted prior to changing the redundancy type. Once written, a save must be performed via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') |
| I32 apexGbeConfInRedundMonitorPeriod | 1.3.6.1.4.1.1166.1.31.7.1.4.1.1 | Integer32 | read-write | This is the time in seconds over which Redundant Gigabit Ethernet Input Transport Stream Pairs will be monitored. Range is 1 to 30 seconds. Primary to Secondary Fail Over - The monitored data rate of the Primary must be below the Secondary by apexManRteGbeInRedThreshold (for Manual Routing) percent for apexGbeConfInRedundMonitorPeriod before fail over to Secondary will occur. Fail over to Secondary will not occur if fail over is suspended for the Primary. Secondary to Primary Switch Back - The monitored data rate of the Primary must have returned above apexManRteGbeInRedThreshold (for Manual Routing) percent below the Secondary for apexGbeConfInRedundMonitorPeriod before switch back to Primary will occur. Switch back to Primary will not occur if fail over is suspended for the Secondary. Once the Primary is restored, switch back to Primary will be delayed by apexGbeConfInRedundSwitchTime when apexGbeConfInRedundAutoSwitchBack is 'enabled'. Note that if apexGbeConfInRedundAutoSwitchBack is 'disabled' switch back will not occur. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') |
| I32 apexGbeConfInRedundSwitchTime | 1.3.6.1.4.1.1166.1.31.7.1.4.1.2 | Integer32 | read-write | This is the time in seconds to wait before switching back to the Primary of a Redundant Gigabit Ethernet Input TS pair after the Primary is healthy. Range is 0 to 3600. This time is in addition to apexGbeConfInRedundMonitorPeriod. Switch back to Primary will not occur if fail over is suspended for the Secondary. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') |
| RAT apexGbeConfLossOfInputTsType | 1.3.6.1.4.1.1166.1.31.7.1.1.12 | RateComparisonTYPE | read-write | Loss of input stream type. Determines if detection of loss of an input stream is based on data rate or stream rate. Data rate includes only non-null MPEG packets (such as video and audio packets). Stream rate includes all packets, including null packets. The loss of an input stream uses the timeout value for the specific input (unicast or multicast) and the input type. If no packets are received within the specified timeout value, taking into account the loss of input type checking, then the input stream is determined to be missing. Data rate should be used for detecting loss of input when the input stream is normally null filled. When a user requires notification of a loss of input stream when there is no content streamed, data rate should be selected. Stream rate should be used for detecting loss of input stream when the user requires to be notified when there is no input stream at all being received. Loss of input is used for determining all SDV failover conditions. It is also used for Manual Routing failover conditions when using hot/warm transport stream redundancy. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexGbeDefaultGateway1 | 1.3.6.1.4.1.1166.1.31.7.1.1.1 | IpAddress | read-write | This is the IP address of the default gateway for Gigabit Ethernet interfaces 1 and 2. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexGbeDefaultGateway2 | 1.3.6.1.4.1.1166.1.31.7.1.1.2 | IpAddress | read-write | This is the IP address of the default gateway for Gigabit Ethernet interfaces 3 and 4. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexGbeFrameBufferAlarmStatus | 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.7 | INTEGER | read-only | The current highest severity of apexAlarmGbeBufferFullness for the GBE Processor. |
| I32 apexGbeFrameBufferCurrMsLevel | 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.3 | Integer32 | read-only | Current highest Gigabit Ethernet Frame Buffer level in milliseconds. |
| I32 apexGbeFrameBufferCurrPercentFull | 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.4 | Integer32 | read-only | Current highest Gigabit Ethernet Frame Buffer fullness as a percentage of the buffer depth available for a given aggregate rate. This percentage is calculated using the current buffer level (apexGbeFrameBufferCurrMsLevel) and the actual input data rate. |
| apexGbeFrameBufferHourlyEntry | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1 | not-accessible | Gigabit Ethernet Interface Frame Buffer Table Entry. | |
| I32 apexGbeFrameBufferHourlyGpsTime | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.9 | Integer32 | read-only | The GPS time when the maximum Gigabit Ethernet frame buffer level was reached. |
| I32 apexGbeFrameBufferHourlyIndex | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.2 | Integer32 | not-accessible | Second index of the Gigabit Ethernet Buffer Status Table. Each index represents one hour. There can be up to 24 entries in the table. The most recent entry is always at the beginning of the table. |
| I32 apexGbeFrameBufferHourlyInInterface | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.3 | Integer32 | read-only | Number of the input interface for the Gigabit Ethernet interface that experienced the highest buffer level for the hour. |
| IP apexGbeFrameBufferHourlyInMulticastIp | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.5 | IpAddress | read-only | Input Multicast IP address for the Gigabit Ethernet interface that experienced the highest buffer level for the hour. |
| IP apexGbeFrameBufferHourlyInSourceIp | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.6 | IpAddress | read-only | Input IGMP v3 Source IP for the Gigabit Ethernet interface that experienced the highest buffer level for the hour. |
| I32 apexGbeFrameBufferHourlyInUdp | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.4 | Integer32 | read-only | Input UDP Port for the Gigabit Ethernet interface that experienced the highest buffer level for the hour. |
| I32 apexGbeFrameBufferHourlyMaxMsLevel | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.7 | Integer32 | read-only | The maximum Gigabit Ethernet frame buffer level (in milliseconds) recorded for the hour. |
| I32 apexGbeFrameBufferHourlyMaxPercentFull | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.8 | Integer32 | read-only | The maximum Gigabit Ethernet frame buffer level percentage recorded for the hour. |
| I32 apexGbeFrameBufferHourlyOverflows | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.10 | Integer32 | read-only | The number of overflows recorded on Gigabit Ethernet interface for the hour. |
| I32 apexGbeFrameBufferHourlyProcessorNum | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.1 | Integer32 | not-accessible | First index of the Gigabit Ethernet Buffer Status Table. Gigabit Ethernet Processor Number. Proc 1 = GBE Interfaces 1 and 2 Proc 2 = GBE Interfaces 3 and 4 |
| I32 apexGbeFrameBufferHourlyResets | 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.11 | Integer32 | read-only | The number of resets reported by the GigE processor during the hour. |
| apexGbeFrameBufferHourlyTable | 1.3.6.1.4.1.1166.1.31.7.2.7.3 | not-accessible | Table of Gigabit Ethernet Frame Buffer Statistics. There can be up to 24 entries in the table for each GBE Processor. Each entry represents one hour. The newest entry is placed at the beginning of the table and, if necessary, the oldest entry is pushed off the end of the table. The table will not be full until 24 hours have passed. | |
| I32 apexGbeFrameBufferOverflowLevel | 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.6 | Integer32 | read-only | The point at which the GigE frame buffer will overflow, in milliseconds. This value is calculated based on the sum of the number of received frames per second for all interfaces. |
| I32 apexGbeFrameBufferProcessorNum | 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.1 | Integer32 | not-accessible | Index of the Gigabit Ethernet Buffer Statistics Table. Gigabit Ethernet Processor Number. Proc 1 = GBE Interfaces 1 and 2 Proc 2 = GBE Interfaces 3 and 4 |
| I32 apexGbeFrameBufferResetLevelLimit | 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.2 | Integer32 | read-only | The point at which the GigE frame buffer will be reset, in milliseconds. This value is equal to (maximum buffer depth - 5). The maximum buffer depth is calculated based on the expected input data rate (apexGbeConfigFrameBufferMaxInDataRate). |
| apexGbeFrameBufferStats | 1.3.6.1.4.1.1166.1.31.7.2.7 | |||
| apexGbeFrameBufferStatsEntry | 1.3.6.1.4.1.1166.1.31.7.2.7.2.1 | not-accessible | Gigabit Ethernet Frame Buffer Statistics Table Entry. | |
| apexGbeFrameBufferStatsGeneral | 1.3.6.1.4.1.1166.1.31.7.2.7.1 | |||
| apexGbeFrameBufferStatsTable | 1.3.6.1.4.1.1166.1.31.7.2.7.2 | not-accessible | Table of Gigabit Ethernet Frame Buffer Statistics for each GBE processor. | |
| I32 apexGbeFrameBufferUnderflowLevel | 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.5 | Integer32 | read-only | The point at which the GigE frame buffer will underflow, in milliseconds. This value is calculated based on the sum of the number of received frames per second for all interfaces. |
| I32 apexGbeFrameCounterGbeInterfaceNum | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.1 | Integer32 | not-accessible | The index of the Gigabit Ethernet Frame Counter Table. Represents the Gigabit Ethernet interface number. |
| RES apexGbeFrameCounterReset | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.2 | ResetStatisticsTYPE | read-write | Reset Ethernet Frame Counter Statistics totals for a single GigE interface: - apexGbeTotalRxSinglecastFrames - apexGbeTotalRxMulticastFrames - apexGbeTotalRxBroadcastFrames - apexGbeTotalRxErrorFrames - apexGbeTotalRxFrames - apexGbeTotalTxGoodFrames - apexGbeTotalTxErrorFrames Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| I32 apexGbeFrameCounterUpdateInterval | 1.3.6.1.4.1.1166.1.31.7.2.6.1.2 | Integer32 | read-only | Time in seconds between Gigabit Ethernet Frame Counter updates. The count during this time is defined as one sample. This time applies to packet counts contained in apexGbeStatusFrameCounterTable. To compute rate from frame count for the last update interval: Rate(bps) = (Frame_Count * 7 packets/frame 188 bytes/packet * 8 bits/byte) / Update_Interval This value is set by the APEX at startup and is constant. |
| I32 apexGbeGarpPeriodicity | 1.3.6.1.4.1.1166.1.31.7.1.1.4 | Integer32 | read-write | Gratuitous ARP period in range of 20 to 300 seconds. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexGbeInputDataTsBufferDepth | 1.3.6.1.4.1.1166.1.31.7.1.1.8 | Integer32 | read-write | GBE Input Data stream buffer depth. Amount of time in milliseconds that the GigE will buffer input streams that do not contain PCRs. This allows the GigE to buffer these streams to remove network jitter and then play them out with the packets equally spaced out. The buffer depth must be equal to or greater than the data stream smoothing period. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') |
| I32 apexGbeInputDataTsSmoothingPeriod | 1.3.6.1.4.1.1166.1.31.7.1.1.7 | Integer32 | read-write | Input Data stream smoothing period. Amount of time in milliseconds over which the GigE will smooth out input streams that do not contain PCRs. This allows the GigE to play out the input streams with the packets equally spaced out over this period. This helps to reduce network jitter and bursts of data to the output. The smoothing period is used in conjunction with the data stream buffer depth to perform this smoothing algorithm. The smoothing period must be equal to or less than the data stream buffer depth. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') |
| C32 apexGbeInputTsAssignedCount | 1.3.6.1.4.1.1166.1.31.7.2.3.1.2 | Counter32 | read-only | Number of input transport streams assigned to the GigE interface. |
| apexGbeInputTsAssignedEntry | 1.3.6.1.4.1.1166.1.31.7.2.3.1 | not-accessible | Gigabit Ethernet Interface Input TS Assigned Table Entry. | |
| I32 apexGbeInputTsAssignedGbeInterfaceNum | 1.3.6.1.4.1.1166.1.31.7.2.3.1.1 | Integer32 | not-accessible | The index of the Gigabit Ethernet Input TS Assigned Table. Represents the Gigabit Ethernet interface number. |
| apexGbeInputTsAssignedTable | 1.3.6.1.4.1.1166.1.31.7.2.3 | not-accessible | Table of Gigabit Ethernet Input TS Assigned data. | |
| I32 apexGbeInputTsEventAlarmCode | 1.3.6.1.4.1.1166.1.31.200.4.1.3 | Integer32 | read-only | Last number of alarm OID. Can be one of the following: 0 Indicates event is informational and may or may not cause an alarm. 8022 apexAlarmGbeInputStreamLowBitRate 8023 apexAlarmGbeInputStreamHighBitRate 8024 apexAlarmGbeMptsRedundPrimaryThreshold 8025 apexAlarmGbeMptsRedundFailOver More details about the error may be found in apexGbeInputTsEventDescription. |
| INT apexGbeInputTsEventAlarmSeverity | 1.3.6.1.4.1.1166.1.31.200.4.1.4 | INTEGER | read-only | Alarm severity level of this event. |
| STR apexGbeInputTsEventDescription | 1.3.6.1.4.1.1166.1.31.200.4.1.17 | DisplayString | read-only | Text description of the event. Maximum length is 128 characters. |
| apexGbeInputTsEventEntry | 1.3.6.1.4.1.1166.1.31.200.4.1 | not-accessible | Gigabit Ethernet Input Transport Stream Event Table Entry. | |
| I32 apexGbeInputTsEventGbeInterface | 1.3.6.1.4.1.1166.1.31.200.4.1.6 | Integer32 | read-only | Value of apexInputTsStatPriInputInterface or apexInputTsStatSecInputInterface at the time of the event. |
| I32 apexGbeInputTsEventIndex | 1.3.6.1.4.1.1166.1.31.200.4.1.1 | Integer32 | not-accessible | Index to Gigabit Ethernet Input Transport Stream Event table. |
| INP apexGbeInputTsEventInputTsState | 1.3.6.1.4.1.1166.1.31.200.4.1.10 | InputTsStateTYPE | read-only | Value of apexInputTsStatPriState or apexInputTsStatSecState at the time of the event. For threshold or fail over events, the state reported is always the Primary input stream state. |
| IP apexGbeInputTsEventMulticastIp | 1.3.6.1.4.1.1166.1.31.200.4.1.8 | IpAddress | read-only | Value of apexInputTsStatPriInputMulticastIp or apexInputTsStatSecInputMulticastIp at the time of the event. |
| C32 apexGbeInputTsEventPriCurDataCount | 1.3.6.1.4.1.1166.1.31.200.4.1.14 | Counter32 | read-only | Current Primary input data Packet Count at the time of the event. This is the number of data packets received (non-Nulls), during the sample period defined in apexGbeInputTsEventSamplingPeriod. |
| C32 apexGbeInputTsEventPriCurStreamCount | 1.3.6.1.4.1.1166.1.31.200.4.1.13 | Counter32 | read-only | Current Primary input stream Packet Count at the time of the event. This is the number of packets received, including Nulls, during the sample period defined in apexGbeInputTsEventSamplingPeriod. |
| RAT apexGbeInputTsEventRateCompareType | 1.3.6.1.4.1.1166.1.31.200.4.1.11 | RateComparisonTYPE | read-only | Comparison type at time of event (stream or data). |
| INT apexGbeInputTsEventRedundantConfig | 1.3.6.1.4.1.1166.1.31.200.4.1.5 | INTEGER | read-only | Indicates whether this input transport stream was configured as a primary or secondary at the time of the event. |
| I32 apexGbeInputTsEventSamplingPeriod | 1.3.6.1.4.1.1166.1.31.200.4.1.12 | Integer32 | read-only | Sample period in seconds of the stream and data counts reported. Using the sample period and the stream or data counts, the actual input rate at the time of the event can be computed. |
| C32 apexGbeInputTsEventSecCurDataCount | 1.3.6.1.4.1.1166.1.31.200.4.1.16 | Counter32 | read-only | Current Secondary input data Packet Count at the time of the event. This is the number of data packets received (non-Nulls), during the sample period defined in apexGbeInputTsEventSamplingPeriod. |
| C32 apexGbeInputTsEventSecCurStreamCount | 1.3.6.1.4.1.1166.1.31.200.4.1.15 | Counter32 | read-only | Current Secondary input stream Packet Count at the time of the event. This is the number of packets received, including Nulls, during the sample period defined in apexGbeInputTsEventSamplingPeriod. |
| IP apexGbeInputTsEventSourceIp | 1.3.6.1.4.1.1166.1.31.200.4.1.9 | IpAddress | read-only | Value of apexInputTsStatPriInputSourceIp or apexInputTsStatSecInputSourceIp at the time of the event. |
| apexGbeInputTsEventTable | 1.3.6.1.4.1.1166.1.31.200.4 | not-accessible | Table of Gigabit Ethernet Input Transport Stream Events that have occurred. Maximum of 100 events will be recorded. | |
| I32 apexGbeInputTsEventTimeLogged | 1.3.6.1.4.1.1166.1.31.200.4.1.2 | Integer32 | read-only | Time in GPS seconds (apexSystemTime) that this event was logged. |
| I32 apexGbeInputTsEventUdpPort | 1.3.6.1.4.1.1166.1.31.200.4.1.7 | Integer32 | read-only | Value of apexInputTsStatPriInputUdp or apexInputTsStatSecInputUdp at the time of the event. |
| C32 apexGbeIpFragmentedPkts | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.20 | Counter32 | read-only | Number of IP fragmented packets received during last status checking interval. Status checking interval is five seconds. |
| I32 apexGbeJitterAbsorption | 1.3.6.1.4.1.1166.1.31.7.1.1.3 | Integer32 | read-write | This object is obsolete. Jitter Absorption setting in range of 0 to 200 milliseconds in increments of 5 ms. A change to this parameter will cause the Gigabit Ethernet processor to reset all of its internal Ethernet frame buffers. This will result in a momentary loss of data causing a minor glitch on all output streams. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(step=5) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexGbeMaxInputTs | 1.3.6.1.4.1.1166.1.31.7.2.1.3 | Integer32 | read-only | Maximum number of Gigabit Ethernet input transport streams that can be opened on this APEX. This is the maximum across all installed GigE interfaces. One GigE interface can use all Input TS. |
| I32 apexGbeNominalBufferLevel | 1.3.6.1.4.1.1166.1.31.7.1.1.6 | Integer32 | read-write | Gigabit Ethernet Nominal Buffer Level. Range of 50 to 475 milliseconds in increments of 5 ms. A change to this parameter will cause the Gigabit Ethernet processor to reset all of its internal Ethernet frame buffers. This will result in a momentary loss of data causing a minor glitch on all output streams. The buffer level is the normal standard starting level for an input stream buffer. It is highly recommended that this level not be changed from its default setting. The buffer level needs to be set at an appropriate amount to allow for network jitter, clock skew between the APEX and input source, and for maximum time between PCRs (100ms). In addition, the level must not be set too high as the buffer needs to be able to grow as packets are received and PCR processing is applied. This buffer level is the initial level the APEX will attempt to maintain at all times. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| C32 apexGbeOpenInputUdpPortCount | 1.3.6.1.4.1.1166.1.31.7.2.4.1.2 | Counter32 | read-only | Number of open Input UDP Ports on the GigE interface. |
| apexGbeOpenInputUdpPortEntry | 1.3.6.1.4.1.1166.1.31.7.2.4.1 | not-accessible | Gigabit Ethernet Interface Input Open UDP Port Table Entry. | |
| I32 apexGbeOpenInputUdpPortGbeInterfaceNum | 1.3.6.1.4.1.1166.1.31.7.2.4.1.1 | Integer32 | not-accessible | The index of the Gigabit Ethernet Input Open UDP Port Table. Represents the Gigabit Ethernet interface number. |
| apexGbeOpenInputUdpPortTable | 1.3.6.1.4.1.1166.1.31.7.2.4 | not-accessible | Table of Gigabit Ethernet Input Open UDP Port data. | |
| I32 apexGbeRoutedPacketUpdateInterval | 1.3.6.1.4.1.1166.1.31.7.2.1.4 | Integer32 | read-only | Time in seconds between Gigabit Ethernet Routed Packet Count updates. The count during this time is defined as one sample. This time applies to packet counts contained in apexGbeStatusRoutedPacketTable. To compute rate from packet count for the last update interval: Rate(bps) = (Packet_Count * 188 bytes/packet * 8 bits/byte) / Update_Interval This value is set by the APEX at startup and is constant. |
| C32 apexGbeRxBroadcastFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.10 | Counter32 | read-only | Number of broadcast Ethernet frames received during last status checking interval. Status checking interval is apexGbeFrameCounterUpdateInterval. |
| C32 apexGbeRxDocsisFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.17 | Counter32 | read-only | Number of good Ethernet frames containing DOCSIS (singlecast, multicast, and broadcast) received during last status checking interval. Status checking interval is five seconds. |
| C32 apexGbeRxErrorFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.11 | Counter32 | read-only | Number of bad Ethernet frames received during last status checking interval. Status checking interval is apexGbeFrameCounterUpdateInterval. |
| C32 apexGbeRxFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.12 | Counter32 | read-only | Number of Ethernet frames received during last status checking interval. This is the sum of apexGbeRxSinglecastFrames, apexGbeRxMulticastFrames, apexGbeRxBroadcastFrames, and apexGbeRxErrorFrames. Status checking interval is five seconds. |
| C32 apexGbeRxMpegDocsisFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.19 | Counter32 | read-only | Number of MPEG packets generated from DOCSIS data (singlecast, multicast, and broadcast) received during last status checking interval. Status checking interval is five seconds. |
| C32 apexGbeRxMulticastFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.9 | Counter32 | read-only | Number of multicast Ethernet frames received during last status checking interval. Status checking interval is apexGbeFrameCounterUpdateInterval. |
| C32 apexGbeRxSinglecastFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.8 | Counter32 | read-only | Number of singlecast Ethernet frames received during last status checking interval. Status checking interval is apexGbeFrameCounterUpdateInterval. |
| apexGbeSfp | 1.3.6.1.4.1.1166.1.31.7.3 | |||
| apexGbeSfpConfig | 1.3.6.1.4.1.1166.1.31.7.3.1 | |||
| apexGbeSfpConfigGeneral | 1.3.6.1.4.1.1166.1.31.7.3.1.1 | |||
| apexGbeSfpStatus | 1.3.6.1.4.1.1166.1.31.7.3.2 | |||
| STR apexGbeSfpStatusDiagInfo | 1.3.6.1.4.1.1166.1.31.7.3.2.2.1.3 | DisplayString | read-only | ASCII format of bytes 96-127 from SFP Diagnostic Memory address A2h. Zero-length indicates that diagnostic information is not available. |
| apexGbeSfpStatusEntry | 1.3.6.1.4.1.1166.1.31.7.3.2.2.1 | not-accessible | SFP status table entry. | |
| I32 apexGbeSfpStatusGbeIfNum | 1.3.6.1.4.1.1166.1.31.7.3.2.2.1.1 | Integer32 | not-accessible | Gigabit Ethernet Interface Number. |
| apexGbeSfpStatusGeneral | 1.3.6.1.4.1.1166.1.31.7.3.2.1 | |||
| apexGbeSfpStatusTable | 1.3.6.1.4.1.1166.1.31.7.3.2.2 | not-accessible | Table of SFP status parameters. Indexed by Gigabit Ethernet Interface Number. | |
| STR apexGbeSfpStatusVendorId | 1.3.6.1.4.1.1166.1.31.7.3.2.2.1.2 | DisplayString | read-only | ASCII format of bytes 0-127 from SFP-MSA ID Memory Map address A0h. Zero-length indicates that no SFP module is installed. |
| INT apexGbeSfpUpdateStatus | 1.3.6.1.4.1.1166.1.31.7.3.1.1.1 | INTEGER | read-write | When set to 'update' the APEX will update the apexGbeSfpStatusTable by performing an one-time read of SFP memory. APEX sets back to 'updateNotInProgress' when complete. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| I32 apexGbeStatInTsErrorInputTsNum | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.1 | Integer32 | not-accessible | The Gigabit Ethernet Input Transport Stream Error Status table index. A row in this table corresponds to the same index row in apexInputTsStatTable and apexGbeStatusInputTsTable. |
| I32 apexGbeStatInTsInputTsNum | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.1 | Integer32 | not-accessible | The Gigabit Ethernet Input Transport Stream Status table index. A row in this table corresponds to the same index row in apexInputTsStatTable and apexGbeStatusInputTsErrorTable. |
| INT apexGbeStatInTsMptsRedundFailError | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.6 | INTEGER | read-only | The current fail over state for a redundancy pair. Ok indicates no errors or input stream is not part of a redundant pair. Error indicates primary input stream is no longer in use and the APEX has fallen over to use the secondary input stream. |
| INT apexGbeStatInTsMptsRedundPriError | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.5 | INTEGER | read-only | The current redundant threshold state for the primary input stream. Ok indicates no errors or input stream is not part of a redundant pair. Error indicates primary input stream is below the threshold level specified. |
| C32 apexGbeStatInTsPriAvgDataCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.4 | Counter32 | read-only | The Average Data Packet Count per sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsPriAvgStreamCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.8 | Counter32 | read-only | The Average Transport Stream Packet Count per sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsPriCurDataCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.3 | Counter32 | read-only | The Data Packet Count of the most recent sample for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsPriCurStreamCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.7 | Counter32 | read-only | The Transport Stream Packet Count of the most recent sample for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| INT apexGbeStatInTsPriErrorSummary | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.2 | INTEGER | read-only | The current highest error of the following errors for the primary input transport stream: apexGbeStatInTsPriLowBitRateError apexGbeStatInTsPriHighBitRateError apexGbeStatInTsMptsRedundPriError apexGbeStatInTsMptsRedundFailError apexGbeStatInTsPriLossInputError |
| INT apexGbeStatInTsPriHighBitRateError | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.4 | INTEGER | read-only | The current high bit rate state for the primary input stream. Ok indicates no errors or not checking high bit rate. Error indicates primary input stream is above the high bit rate specified. |
| INT apexGbeStatInTsPriLossInputError | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.10 | INTEGER | read-only | The current loss of input stream state for the primary input stream. Ok indicates no errors or not checking for loss of input stream. Error indicates primary input stream is missing. |
| INT apexGbeStatInTsPriLowBitRateError | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.3 | INTEGER | read-only | The current low bit rate state for the primary input stream. Ok indicates no errors or not checking low bit rate. Error indicates primary input stream is below the low bit rate specified. |
| C32 apexGbeStatInTsPriMinDataCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.5 | Counter32 | read-only | The Minimum Data Packet Count sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsPriMinStreamCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.9 | Counter32 | read-only | The Minimum Transport Stream Packet Count sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsPriPeakDataCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.6 | Counter32 | read-only | The Peak Data Packet Count sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsPriPeakStreamCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.10 | Counter32 | read-only | The Peak Transport Stream Packet Count sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| I32 apexGbeStatInTsSamplingPeriod | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.2 | Integer32 | read-only | The total time, in seconds, over which the packet counts statistics in this row have been collected. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsSecAvgDataCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.12 | Counter32 | read-only | The Average Data Packet Count per sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsSecAvgStreamCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.16 | Counter32 | read-only | The Average Transport Stream Packet Count per sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsSecCurDataCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.11 | Counter32 | read-only | The Data Packet Count of the most recent sample for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsSecCurStreamCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.15 | Counter32 | read-only | The Transport Stream Packet Count of the most recent sample for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| INT apexGbeStatInTsSecErrorSummary | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.7 | INTEGER | read-only | The current highest error state of the following for the secondary input transport stream: apexGbeStatInTsSecLowBitRateError apexGbeStatInTsSecHighBitRateError apexGbeStatInTsSecLossInputError |
| INT apexGbeStatInTsSecHighBitRateError | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.9 | INTEGER | read-only | The current high bit rate state for the secondary input stream. Ok indicates no errors or not checking high bit rate. Error indicates secondary input stream is above the high bit rate specified. |
| INT apexGbeStatInTsSecLossInputError | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.11 | INTEGER | read-only | The current loss of input stream state for the secondary input stream. Ok indicates no errors or not checking for loss of input stream. Error indicates secondary input stream is missing. |
| INT apexGbeStatInTsSecLowBitRateError | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.8 | INTEGER | read-only | The current low bit rate state for the secondary input stream. Ok indicates no errors or not checking low bit rate. Error indicates secondary input stream is below the low bit rate specified. |
| C32 apexGbeStatInTsSecMinDataCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.13 | Counter32 | read-only | The Minimum Data Packet Count sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsSecMinStreamCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.17 | Counter32 | read-only | The Minimum Transport Stream Packet Count sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsSecPeakDataCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.14 | Counter32 | read-only | The Peak Data Packet Count sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| C32 apexGbeStatInTsSecPeakStreamCount | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.18 | Counter32 | read-only | The Peak Transport Stream Packet Count sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates. |
| apexGbeStatus | 1.3.6.1.4.1.1166.1.31.7.2 | |||
| apexGbeStatusEntry | 1.3.6.1.4.1.1166.1.31.7.2.2.1 | not-accessible | Gigabit Ethernet Interface Status Table Entry. | |
| apexGbeStatusFrameCounter | 1.3.6.1.4.1.1166.1.31.7.2.6 | |||
| apexGbeStatusFrameCounterEntry | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1 | not-accessible | Gigabit Ethernet Interface Frame Counter Table Entry. | |
| apexGbeStatusFrameCounterGeneral | 1.3.6.1.4.1.1166.1.31.7.2.6.1 | |||
| apexGbeStatusFrameCounterTable | 1.3.6.1.4.1.1166.1.31.7.2.6.2 | not-accessible | Table of Gigabit Ethernet Frame Counter Statistics. | |
| RES apexGbeStatusFrameCounterTableResetAll | 1.3.6.1.4.1.1166.1.31.7.2.6.1.1 | ResetStatisticsTYPE | read-write | Reset Ethernet Frame Counter Totals for all GigE interfaces: - apexGbeTotalRxSinglecastFrames - apexGbeTotalRxMulticastFrames - apexGbeTotalRxBroadcastFrames - apexGbeTotalRxErrorFrames - apexGbeTotalRxFrames - apexGbeTotalTxGoodFrames - apexGbeTotalTxErrorFrames Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| I32 apexGbeStatusGbeInterfaceNum | 1.3.6.1.4.1.1166.1.31.7.2.2.1.1 | Integer32 | not-accessible | Gigabit Ethernet Interface Number. |
| apexGbeStatusGeneral | 1.3.6.1.4.1.1166.1.31.7.2.1 | |||
| INT apexGbeStatusIgmpVersion | 1.3.6.1.4.1.1166.1.31.7.2.2.1.4 | INTEGER | read-only | This indicates the IGMP Version being used on this interface. |
| apexGbeStatusInputTransportStream | 1.3.6.1.4.1.1166.1.31.7.2.8 | |||
| apexGbeStatusInputTsEntry | 1.3.6.1.4.1.1166.1.31.7.2.8.2.1 | not-accessible | Gigabit Ethernet Input Transport Stream Status Table Entry. | |
| apexGbeStatusInputTsErrorEntry | 1.3.6.1.4.1.1166.1.31.7.2.8.3.1 | not-accessible | Gigabit Ethernet Input Transport Stream Status Table Entry. | |
| apexGbeStatusInputTsErrorTable | 1.3.6.1.4.1.1166.1.31.7.2.8.3 | not-accessible | Table of Gigabit Ethernet Input Transport Stream Error status. A row in this table corresponds to the same index row in apexInputTsStatTable and apexGbeStatusInputTsTable. | |
| apexGbeStatusInputTsGeneral | 1.3.6.1.4.1.1166.1.31.7.2.8.1 | |||
| apexGbeStatusInputTsTable | 1.3.6.1.4.1.1166.1.31.7.2.8.2 | not-accessible | Table of Gigabit Ethernet Input Transport Stream status. A row in this table corresponds to the same index row in apexInputTsStatTable and apexGbeStatusInputTsErrorTable. Packet Counts are updated every apexGbeStatusInputTsUpdateInterval. The count during a apexGbeStatusInputTsUpdateInterval is a sample. The samples are accumulated into a set of rolling statistics that cover a maximum of a 15 minute sampling time period. The sampling period is the amount of time over which the data in the corresponding row has been collected. When the sampling period reaches 15 minutes, old data is removed from the accumulated statistics and new data is rolled in. In this way, the average, minimum, and peak rates for the sampling period are maintained. | |
| I32 apexGbeStatusInputTsUpdateInterval | 1.3.6.1.4.1.1166.1.31.7.2.8.1.1 | Integer32 | read-only | Time in seconds between Gigabit Ethernet Input Transport Stream Packet Count updates. The count during this time is defined as one sample. This time applies to packet counts contained in apexGbeStatusInputTsTable. To compute rate from packet count for the last update interval: Rate(bps) = (Packet_Count * 188 bytes/packet * 8 bits/byte) / Update_Interval This value is set by the APEX at startup and is constant. |
| apexGbeStatusInterfaceRedund | 1.3.6.1.4.1.1166.1.31.7.2.9 | |||
| I32 apexGbeStatusInterfaceRedundActiveIf | 1.3.6.1.4.1.1166.1.31.7.2.9.1.1.2 | Integer32 | read-only | The current active interface for the redundant pair. This is only applicable if GbE Interface Redundancy is enabled for the pair. If GbE Interface Redundancy is not enabled it will be set to zero. |
| apexGbeStatusInterfaceRedundEntry | 1.3.6.1.4.1.1166.1.31.7.2.9.1.1 | not-accessible | GbE Interface Redundancy Status Table Entry. | |
| INT apexGbeStatusInterfaceRedundFaultCondition | 1.3.6.1.4.1.1166.1.31.7.2.9.1.1.4 | INTEGER | read-only | Current fault condition of the GbE Interface pair. Reflects apexAlarmGbeInterfaceRedundFailOver for this redundant pair. |
| I32 apexGbeStatusInterfaceRedundIndex | 1.3.6.1.4.1.1166.1.31.7.2.9.1.1.1 | Integer32 | not-accessible | GbE Interface Pair number. Value of 1 is GbE1 and GbE2 pair. Value of 2 is GbE3 and GbE4 pair. |
| STR apexGbeStatusInterfaceRedundInvalidApplyText | 1.3.6.1.4.1.1166.1.31.7.2.9.1.1.3 | DisplayString | read-only | When apexGbeConfIfRedundApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of an entry that was invalid. |
| apexGbeStatusInterfaceRedundTable | 1.3.6.1.4.1.1166.1.31.7.2.9.1 | not-accessible | This is a table of status parameters for GbE Interface Redundancy. | |
| ACT apexGbeStatusLinkActive | 1.3.6.1.4.1.1166.1.31.7.2.2.1.3 | ActiveTYPE | read-only | This indicates if the Gigabit Ethernet optical link is active. |
| INT apexGbeStatusLossOfPhysicalInput | 1.3.6.1.4.1.1166.1.31.7.2.2.1.5 | INTEGER | read-only | The current severity of apexAlarmGbeLossOfPhysicalInput for this interface. |
| STR apexGbeStatusMacAddr | 1.3.6.1.4.1.1166.1.31.7.2.2.1.2 | DisplayString | read-only | This is the MAC address of the Gigabit Ethernet Interface. It is set at the factory and cannot be changed. The string length is 17 characters in the format 'hh:hh:hh:hh:hh:hh' where 'hh' is a hexadecimal number. |
| C32 apexGbeStatusNumRoutedPackets | 1.3.6.1.4.1.1166.1.31.7.2.5.1.3 | Counter32 | read-only | Number of Gigabit Ethernet MPEG packets routed to this Output Transport Stream during the last monitoring period (apexGbeRoutedPacketUpdateInterval). |
| apexGbeStatusRoutedPacketEntry | 1.3.6.1.4.1.1166.1.31.7.2.5.1 | not-accessible | Gigabit Ethernet Interface Status Routed Packet Table Entry. | |
| I32 apexGbeStatusRoutedPacketOutputTsNum | 1.3.6.1.4.1.1166.1.31.7.2.5.1.1 | Integer32 | not-accessible | The index of the Gigabit Ethernet Routed Packet Status Table. Represents Output Transport Stream number. |
| apexGbeStatusRoutedPacketTable | 1.3.6.1.4.1.1166.1.31.7.2.5 | not-accessible | This table contains Gigabit Ethernet MPEG packet counts for each Output Transport Stream of this APEX. Update interval is apexGbeRoutedPacketUpdateInterval. | |
| apexGbeStatusTable | 1.3.6.1.4.1.1166.1.31.7.2.2 | not-accessible | This is a table of status parameters for the Gigabit Ethernet Interface. | |
| C32 apexGbeStatusTotRoutedPackets | 1.3.6.1.4.1.1166.1.31.7.2.5.1.2 | Counter32 | read-only | Total number of Gigabit Ethernet MPEG packets routed to this Output Transport Stream. |
| C32 apexGbeTotalIpFragmentedPkts | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.21 | Counter32 | read-only | Total number of IP fragmented packets received during last status checking interval. Status checking interval is five seconds. |
| C32 apexGbeTotalRxBroadcastFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.5 | Counter32 | read-only | Total number of broadcast Ethernet frames received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset. |
| C32 apexGbeTotalRxDocsisFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.18 | Counter32 | read-only | Total number of good Ethernet frames containing DOCSIS(singlecast, multicast, and broadcast) received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset. |
| C32 apexGbeTotalRxErrorFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.6 | Counter32 | read-only | Total number of bad Ethernet frames received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset. |
| C32 apexGbeTotalRxFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.7 | Counter32 | read-only | Total number of Ethernet frames received since last reset. This is the sum of apexGbeTotalRxSinglecastFrames, apexGbeTotalRxMulticastFrames, apexGbeTotalRxBroadcastFrames, and apexGbeTotalRxErrorFrames. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset. |
| C32 apexGbeTotalRxMulticastFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.4 | Counter32 | read-only | Total number of multicast Ethernet frames received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset. |
| C32 apexGbeTotalRxSinglecastFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.3 | Counter32 | read-only | Total number of singlecast Ethernet frames received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset. |
| C32 apexGbeTotalTxErrorFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.14 | Counter32 | read-only | Total number of bad Ethernet frames transmitted since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset. |
| C32 apexGbeTotalTxGoodFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.13 | Counter32 | read-only | Total number of good Ethernet frames (singlecast, multicast, and broadcast) transmitted since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset. |
| C32 apexGbeTxErrorFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.16 | Counter32 | read-only | Number of bad Ethernet frames transmitted during last status checking interval. Status checking interval is five seconds. |
| C32 apexGbeTxGoodFrames | 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.15 | Counter32 | read-only | Number of good Ethernet frames (singlecast, multicast, and broadcast) transmitted during last status checking interval. Status checking interval is five seconds. |
| STR apexGlueCpldVersion | 1.3.6.1.4.1.1166.1.31.1.2.2.9 | DisplayString | read-only | APEX Glue CPLD Version. |
| STR apexGlueFpgaVersion | 1.3.6.1.4.1.1166.1.31.1.2.2.8 | DisplayString | read-only | APEX Glue FPGA Version. |
| STR apexHostApplicationDate | 1.3.6.1.4.1.1166.1.31.1.2.2.5 | DisplayString | read-only | APEX Host Processor Application Creation Date. |
| STR apexHostProcessorBootCodeVersion | 1.3.6.1.4.1.1166.1.31.1.2.2.1 | DisplayString | read-only | APEX Host Processor Boot Code Version. |
| I32 apexHwEventAlarmCode | 1.3.6.1.4.1.1166.1.31.200.1.1.3 | Integer32 | read-only | Last number of alarm OID. Can be one of the following: 0 Indicates event is informational and may or may not cause an alarm. 8000 apexAlarmHardwareFault 8002 apexAlarmTemperatureFault 8003 apexAlarmFanFault 8004 apexAlarmPowerFault 8042 apexAlarmQamModuleFault 8043 apexAlarmQamRfPortFault 8044 apexAlarmQamChannelFault 8045 apexAlarmQamRfRedundFailOver 8046 apexAlarmQamRfRedundMismatch 8070 apexAlarmRemCommFault 8071 apexAlarmRemFault More details about the error can be found in apexHwEventDescription. |
| INT apexHwEventAlarmSeverity | 1.3.6.1.4.1.1166.1.31.200.1.1.4 | INTEGER | read-only | Alarm severity level of this event. |
| I32 apexHwEventData | 1.3.6.1.4.1.1166.1.31.200.1.1.5 | Integer32 | read-only | Additional integer data. When apexHwEventAlarmCode is non-zero, this will be the same as Additional Data 1 as in the trap for the alarm. When apexHwEventAlarmCode is zero, this may contain additional data helpful in debug. |
| STR apexHwEventDescription | 1.3.6.1.4.1.1166.1.31.200.1.1.6 | DisplayString | read-only | Text description of the event. |
| apexHwEventEntry | 1.3.6.1.4.1.1166.1.31.200.1.1 | not-accessible | Hardware Event Table Entry. | |
| I32 apexHwEventIndex | 1.3.6.1.4.1.1166.1.31.200.1.1.1 | Integer32 | not-accessible | Index to HW Event table entry. |
| apexHwEventTable | 1.3.6.1.4.1.1166.1.31.200.1 | not-accessible | Table of Hardware Events that have occurred. Maximum of 100 events will be recorded. | |
| I32 apexHwEventTimeLogged | 1.3.6.1.4.1.1166.1.31.200.1.1.2 | Integer32 | read-only | Time in GPS seconds (apexSystemTime) that this event was logged. |
| apexInputTransport | 1.3.6.1.4.1.1166.1.31.13 | |||
| apexInputTsConfig | 1.3.6.1.4.1.1166.1.31.13.1 | |||
| apexInputTsConfigGeneral | 1.3.6.1.4.1.1166.1.31.13.1.1 | |||
| apexInputTsStatEntry | 1.3.6.1.4.1.1166.1.31.13.2.2.1 | not-accessible | Input Transport Stream Status Table Entry. | |
| I32 apexInputTsStatIndex | 1.3.6.1.4.1.1166.1.31.13.2.2.1.1 | Integer32 | not-accessible | Index of Input Transport Stream Status Table. |
| INT apexInputTsStatInputType | 1.3.6.1.4.1.1166.1.31.13.2.2.1.3 | INTEGER | read-only | Input Type of both primary and secondary inputs. |
| I32 apexInputTsStatPriInputInterface | 1.3.6.1.4.1.1166.1.31.13.2.2.1.6 | Integer32 | read-only | Number of the primary input interface of type Input Type. |
| IP apexInputTsStatPriInputMulticastIp | 1.3.6.1.4.1.1166.1.31.13.2.2.1.8 | IpAddress | read-only | The Multicast receive IP address for primary input. |
| IP apexInputTsStatPriInputSourceIp | 1.3.6.1.4.1.1166.1.31.13.2.2.1.9 | IpAddress | read-only | This is the IGMP v3 Source IP address of the source device for the primary input. |
| I32 apexInputTsStatPriInputUdp | 1.3.6.1.4.1.1166.1.31.13.2.2.1.7 | Integer32 | read-only | Input UDP Port for primary input. |
| INP apexInputTsStatPriState | 1.3.6.1.4.1.1166.1.31.13.2.2.1.5 | InputTsStateTYPE | read-only | The current state of the primary Gigabit Ethernet Input TS configured in apexManRteGbeInRedTable. States are: closed (0) - Input TS is closed or table row is not in use. openedInUse (1) - Input TS is opened and in use. openedBackup (2) - Input TS is opened as backup only. openedTransToBackup (3) - Input TS is opened, transitioning to backup state. openedTransToInUse (4) - Input TS is opened, transitioning to in use state. The states of 'openedBackup', 'openedTransToBackup', and 'openedTransToBackup' apply only to Redundant Pairs. The state of 'openedBackup' applies to the Input TS of the pair that is not currently in use. The state of 'openedTransToBackup' applies to the Input TS of the pair that is currently in use but is transitioning to be the backup, as when a Fail Over or Switch Back is occurring. The state of 'openedTransToInUse' applies to the Input TS of the pair that is currently the backup use but is transitioning to be the in use, as when a Fail Over or Switch Back is occurring. |
| RAT apexInputTsStatRateCompareType | 1.3.6.1.4.1.1166.1.31.13.2.2.1.15 | RateComparisonTYPE | read-only | This is the rate in use for comparing input streams. It is either Information rate or Stream rate. This applies to monitoring for Bit Rate alarming and monitoring of Redundant Pairs. |
| INT apexInputTsStatRoutingType | 1.3.6.1.4.1.1166.1.31.13.2.2.1.4 | INTEGER | read-only | Routing Type of both primary and secondary inputs. 'session' - applies to SDV session routes (RPC, RTSP). 'manual' - applies to all manual routes (Manual Routing, PID Mapping, and stream pass through). 'udpMapping - applies to UDP Port Mapping routes. |
| I32 apexInputTsStatSecInputInterface | 1.3.6.1.4.1.1166.1.31.13.2.2.1.11 | Integer32 | read-only | Number of the secondary input interface of type Input Type. |
| IP apexInputTsStatSecInputMulticastIp | 1.3.6.1.4.1.1166.1.31.13.2.2.1.13 | IpAddress | read-only | The Multicast receive IP address for secondary input. |
| IP apexInputTsStatSecInputSourceIp | 1.3.6.1.4.1.1166.1.31.13.2.2.1.14 | IpAddress | read-only | This is the IGMP v3 Source IP address of the source device for the secondary input. |
| I32 apexInputTsStatSecInputUdp | 1.3.6.1.4.1.1166.1.31.13.2.2.1.12 | Integer32 | read-only | Input UDP Port for secondary input. |
| INP apexInputTsStatSecState | 1.3.6.1.4.1.1166.1.31.13.2.2.1.10 | InputTsStateTYPE | read-only | The current state of the secondary Gigabit Ethernet Input TS configured in apexManRteGbeInRedTable. States are: closed (0) - Input TS is closed or table row is not in use. openedInUse (1) - Input TS is opened and in use. openedBackup (2) - Input TS is opened as backup only. openedTransToBackup (3) - Input TS is opened, transitioning to backup state. openedTransToInUse (4) - Input TS is opened, transitioning to in use state. The states of 'openedBackup', 'openedTransToBackup', and 'openedTransToBackup' apply only to Redundant Pairs. The state of 'openedBackup' applies to the Input TS of the pair that is not currently in use. The state of 'openedTransToBackup' applies to the Input TS of the pair that is currently in use but is transitioning to be the backup, as when a Fail Over or Switch Back is occurring. The state of 'openedTransToInUse' applies to the Input TS of the pair that is currently the backup use but is transitioning to be the in use, as when a Fail Over or Switch Back is occurring. |
| INT apexInputTsStatStreamInUse | 1.3.6.1.4.1.1166.1.31.13.2.2.1.2 | INTEGER | read-only | Indicates whether the primary or secondary is in use. Zero indicates this row is not in use. |
| apexInputTsStatTable | 1.3.6.1.4.1.1166.1.31.13.2.2 | not-accessible | Table of Input Transport Stream Status data. For each input stream in use, an entry in this row will be utilized. This table will indicate the input stream in use by type, interface, UDP, multicast IP, and Source IP address. This table will also indicate if the input stream is a Primary or Secondary input stream. Table of 768 GigE entries plus 16 Host entries (784 total input entries). List of GigE and Host Ethernet input streams currently in use. Each row contains an entry for Primary and Secondary information along with the 1 currently in use. | |
| apexInputTsStatus | 1.3.6.1.4.1.1166.1.31.13.2 | |||
| apexInputTsStatusGeneral | 1.3.6.1.4.1.1166.1.31.13.2.1 | |||
| apexInsertion | 1.3.6.1.4.1.1166.1.31.12 | |||
| apexInsertionConfig | 1.3.6.1.4.1.1166.1.31.12.1 | |||
| apexInsertionConfigGeneral | 1.3.6.1.4.1.1166.1.31.12.1.1 | |||
| INT apexInsertionMode | 1.3.6.1.4.1.1166.1.31.12.1.1.1 | INTEGER | read-write | This parameter is used to set the insertion mode for the APEX. The APEX may be configured to insert messages as efficiently as possible (efficient) or restrict insertion to a single section starting per packet (singleSection). Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexInsertionStatus | 1.3.6.1.4.1.1166.1.31.12.2 | |||
| apexInsertionStatusGeneral | 1.3.6.1.4.1.1166.1.31.12.2.1 | |||
| apexInsertPacketStatisticsEntry | 1.3.6.1.4.1.1166.1.31.12.2.2.1 | not-accessible | A row in the Output Transport Stream Insert Packet Statistics table. | |
| apexInsertPacketStatisticsTable | 1.3.6.1.4.1.1166.1.31.12.2.2 | not-accessible | Table of Output Transport Stream Insert Packet Statistics. Indexed by Output Transport Stream number. | |
| I32 apexInsertPacketStatNumPkts | 1.3.6.1.4.1.1166.1.31.12.2.2.1.3 | Integer32 | read-only | Number of packets inserted during the last monitoring period (currently 5 seconds). |
| I32 apexInsertPacketStatOutputTsNum | 1.3.6.1.4.1.1166.1.31.12.2.2.1.1 | Integer32 | not-accessible | Output Transport Stream Number. |
| I32 apexInsertPacketStatTotPkts | 1.3.6.1.4.1.1166.1.31.12.2.2.1.2 | Integer32 | read-only | Total number of packets inserted. |
| STR apexInvalidInitDataDescription | 1.3.6.1.4.1.1166.1.31.200.2.1.3 | DisplayString | read-only | Text string describing the data error. |
| apexInvalidInitDataEntry | 1.3.6.1.4.1.1166.1.31.200.2.1 | not-accessible | Invalid Initialization Data Table Entry. | |
| I32 apexInvalidInitDataIndex | 1.3.6.1.4.1.1166.1.31.200.2.1.1 | Integer32 | not-accessible | Index to Invalid Initialization Data table entry. |
| apexInvalidInitDataTable | 1.3.6.1.4.1.1166.1.31.200.2 | not-accessible | Table of Invalid Initialization Data Errors. Maximum of 100 errors will be recorded. | |
| I32 apexInvalidInitDataTimeLogged | 1.3.6.1.4.1.1166.1.31.200.2.1.2 | Integer32 | read-only | Time in GPS seconds (apexSystemTime) that this event was logged. |
| apexLogs | 1.3.6.1.4.1.1166.1.31.200 | |||
| I32 apexMainBoardTempAcpModule | 1.3.6.1.4.1.1166.1.31.3.2.2.3 | Integer32 | read-only | Ambient temperature at the ACP Module location. This reading is valid for all models whether an ACP Module is standard on the model. Measured in whole number degrees Celsius. |
| INT apexMainBoardTempAcpModuleFault | 1.3.6.1.4.1.1166.1.31.3.2.3.3 | INTEGER | read-only | Fault status of ambient temperature at the ACP Module location. |
| apexMainBoardTemperature | 1.3.6.1.4.1.1166.1.31.3.2.2 | |||
| apexMainBoardTemperatureFault | 1.3.6.1.4.1.1166.1.31.3.2.3 | |||
| I32 apexMainBoardTempFrontIntake | 1.3.6.1.4.1.1166.1.31.3.2.2.1 | Integer32 | read-only | Ambient temperature at the intake vent at the front of the unit. Measured in whole number degrees Celsius. |
| INT apexMainBoardTempFrontIntakeFault | 1.3.6.1.4.1.1166.1.31.3.2.3.1 | INTEGER | read-only | Fault status of ambient temperature at the intake vent at the front of the unit. |
| I32 apexMainBoardTempHostProcessor | 1.3.6.1.4.1.1166.1.31.3.2.2.4 | Integer32 | read-only | Ambient temperature at the Host Processor. Measured in whole number degrees Celsius. |
| INT apexMainBoardTempHostProcessorFault | 1.3.6.1.4.1.1166.1.31.3.2.3.4 | INTEGER | read-only | Fault status of ambient temperature at the Host Processor. |
| I32 apexMainBoardTempMuxFpga | 1.3.6.1.4.1.1166.1.31.3.2.2.2 | Integer32 | read-only | Ambient temperature at the MUX FPGAs. Measured in whole number degrees Celsius. |
| INT apexMainBoardTempMuxFpgaFault | 1.3.6.1.4.1.1166.1.31.3.2.3.2 | INTEGER | read-only | Fault status of ambient temperature at the MUX FPGAs. |
| I32 apexMainBoardType | 1.3.6.1.4.1.1166.1.31.1.2.2.7 | Integer32 | read-only | APEX Main Board Type. The revision is found in apexMainBoardVersion. |
| STR apexMainBoardVersion | 1.3.6.1.4.1.1166.1.31.1.2.2.4 | DisplayString | read-only | APEX Main Board Version. This is the revision of the apexMainBoardType. |
| APP apexManRteGbeInRedApplyChange | 1.3.6.1.4.1.1166.1.31.10.1.6.2.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the row of data in the Manual Routing Gbe Input Ts Configuration Table. A row in this table corresponds to the same row index in the Manual Routing Gbe Input Ts Configuration table. This parameter MUST be set to 'apply' in order for any of the data in the Manual Routing Gbe Input Ts Configuration Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the Manual Routing Gbe Input Ts Configuration Table row has been configured. @Config(config=no, reboot=no) |
| apexManRteGbeInRedApplyEntry | 1.3.6.1.4.1.1166.1.31.10.1.6.2.1 | not-accessible | Manual Routing Gbe Input Ts Configuration Apply Table Entry. | |
| I32 apexManRteGbeInRedApplyIndex | 1.3.6.1.4.1.1166.1.31.10.1.6.2.1.1 | Integer32 | not-accessible | The index of the Manual Routing Gbe Input Ts Configuration Apply Table. |
| apexManRteGbeInRedApplyTable | 1.3.6.1.4.1.1166.1.31.10.1.6.2 | not-accessible | Table of Apply Change for the data for Manual Route Table. A row in this table corresponds to the same row index in the Manual Route table. | |
| apexManRteGbeInRedConfigGeneral | 1.3.6.1.4.1.1166.1.31.10.1.6.1 | |||
| ENA apexManRteGbeInRedEnable | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.9 | EnableDisableTYPE | read-write | This entry is used to enable Redundancy. |
| apexManRteGbeInRedEntry | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1 | not-accessible | Manual Routing Gigabit Ethernet Input Transport Stream Configuration Table Entry. | |
| INT apexManRteGbeInRedForceSwitch | 1.3.6.1.4.1.1166.1.31.10.1.6.4.1.2 | INTEGER | read-write | The Gigabit Ethernet Redundant Pair force switch. This will have no effect if the corresponding row setting of apexManRteGbeInRedEnable is 'disabled'. The corresponding row setting apexManRteGbeInRedSuspend is ignored when 'forceSwitch' is set. The switch will occur even if apexManRteGbeInRedSuspend is 'suspended'. When forced to the Secondary of the pair, the APEX will stay on the Secondary until the user forces back to the Primary. The APEX will not automatically switch back to the Primary when the Primary is restored above the failover threshold. The APEX will not allow a force to the Primary unless the Primary is above the failover threshold. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| apexManRteGbeInRedForceSwitchEntry | 1.3.6.1.4.1.1166.1.31.10.1.6.4.1 | not-accessible | Gigabit Ethernet Input Stream Redundancy Configuration Table Entry. | |
| I32 apexManRteGbeInRedForceSwitchIndex | 1.3.6.1.4.1.1166.1.31.10.1.6.4.1.1 | Integer32 | not-accessible | The Manual Routing Gbe Input Ts Redundancy Configuration table index. A row in this table corresponds to the same index in the apexManRteGbeInRedTable. |
| apexManRteGbeInRedForceSwitchTable | 1.3.6.1.4.1.1166.1.31.10.1.6.4 | not-accessible | This table is the Manual Routing Gigabit Ethernet Input Transport Stream Redundancy Configuration Table. This table contains 768 rows. A row in this table corresponds to the same index in the apexManRteGbeInRedTable. | |
| I32 apexManRteGbeInRedIndex | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.1 | Integer32 | not-accessible | The Manual Routing Gbe Input Ts Configuration table index. |
| STR apexManRteGbeInRedInvalidApplyText | 1.3.6.1.4.1.1166.1.31.10.2.1.3 | DisplayString | read-only | When apexManRteGbeInRedTableApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a table entry that was invalid. |
| I32 apexManRteGbeInRedPriHighAlarmBitRate | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.7 | Integer32 | read-write | This is the bit rate, in bits per second, above which the APEX will issue the apexAlarmGbeInputStreamHighBitRate alarm for the primary interface. The APEX will compare either the current Information rate or Stream rate as configured in apexManRteGbeInRedRateCompareType. Setting to zero disables the bit rate alarming. The APEX updates the bit rate statistics every five seconds. Not supported. |
| I32 apexManRteGbeInRedPriInterface | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.2 | Integer32 | read-write | The primary Gigabit Ethernet Interface. Zero indicates this row of the table is not in use. |
| I32 apexManRteGbeInRedPriLowAlarmBitRate | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.6 | Integer32 | read-write | This is the bit rate, in bits per second, below which the APEX will issue the apexAlarmGbeInputStreamLowBitRate alarm for the primary interface. The APEX will compare either the current Information rate or Stream rate as configured in apexManRteGbeInRedRateCompareType. Setting to zero disables the bit rate alarming. The APEX updates the bit rate statistics every five seconds. |
| IP apexManRteGbeInRedPriMulticastIp | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.4 | IpAddress | read-write | The primary Multicast receive IP address. An IP address of 0.0.0.0 indicates table entry not in use. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved. |
| IP apexManRteGbeInRedPriSourceIp | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.5 | IpAddress | read-write | This is the IP address of the source device for the primary interface. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address. |
| I32 apexManRteGbeInRedPriUdp | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.3 | Integer32 | read-write | The primary Gigabit Ethernet Input UDP Port. |
| RAT apexManRteGbeInRedRateCompareType | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.8 | RateComparisonTYPE | read-write | This is the rate to use for comparing input streams. It is either Information rate or Stream rate. This applies to monitoring for Bit Rate alarming and monitoring of Redundant Pairs. |
| I32 apexManRteGbeInRedSecHighAlarmBitRate | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.17 | Integer32 | read-write | This is the bit rate, in bits per second, above which the APEX will issue the apexAlarmGbeInputStreamHighBitRate alarm for the secondary interface. The APEX will compare either the current Information rate or Stream rate as configured in apexManRteGbeInRedRateCompareType. Setting to zero disables the bit rate alarming. The APEX updates the bit rate statistics every five seconds. Not supported. |
| I32 apexManRteGbeInRedSecInterface | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.12 | Integer32 | read-write | The secondary Gigabit Ethernet Interface for redundancy. Zero is invalid when redundancy is enabled. |
| I32 apexManRteGbeInRedSecLowAlarmBitRate | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.16 | Integer32 | read-write | This is the bit rate, in bits per second, below which the APEX will issue the apexAlarmGbeInputStreamLowBitRate alarm for the secondary interface. The APEX will compare either the current Information rate or Stream rate as configured in apexManRteGbeInRedRateCompareType. Setting to zero disables the bit rate alarming. The APEX updates the bit rate statistics every five seconds. |
| IP apexManRteGbeInRedSecMulticastIp | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.14 | IpAddress | read-write | The secondary Multicast receive IP address for redundancy. An IP address of 0.0.0.0 indicates singlecast only. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved. |
| INT apexManRteGbeInRedSecRedundMcJoin | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.18 | INTEGER | read-write | This is not currently supported and is reserved for future use. |
| IP apexManRteGbeInRedSecSourceIp | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.15 | IpAddress | read-write | This is the IP address of the source device for the secondary interface. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address. |
| I32 apexManRteGbeInRedSecUdp | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.13 | Integer32 | read-write | The secondary Gigabit Ethernet Input UDP Port for redundancy. |
| apexManRteGbeInRedStatusGeneral | 1.3.6.1.4.1.1166.1.31.10.2.2.1 | |||
| apexManRteGbeInRedStatusMapEntry | 1.3.6.1.4.1.1166.1.31.10.2.2.2.1 | not-accessible | Gigabit Ethernet Input Stream Redundancy Configuration and Status Mapping Table Entry. | |
| I32 apexManRteGbeInRedStatusMapIndex | 1.3.6.1.4.1.1166.1.31.10.2.2.2.1.1 | Integer32 | not-accessible | The Manual Routing Gbe Input Ts Redundancy Configuration and status mapping table index. A index in this table corresponds to the same index in the apexManRteGbeInRedTable. |
| I32 apexManRteGbeInRedStatusMapInputTsStatRow | 1.3.6.1.4.1.1166.1.31.10.2.2.2.1.2 | Integer32 | read-only | The Manual Routing Gbe Input TS Status index. This provides the mapping between the entries in apexManRteGbeInRedTable and apexInputTsStatTable. The range of the index is 0 - 784, where 0 indicates no direct association between configuration and status and the 1-784 is the actual Input Stream status row (relative 1). @Config(config=no, reboot=no) |
| apexManRteGbeInRedStatusMapTable | 1.3.6.1.4.1.1166.1.31.10.2.2.2 | not-accessible | This table provides the mapping between the indexes in Manual Routing Gigabit Ethernet Input Transport Stream Redundancy Configuration and Input TS Status. This table contains 768 rows. The index in this table corresponds to the same index in the apexManRteGbeInRedTable. | |
| INT apexManRteGbeInRedSuspend | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.11 | INTEGER | read-write | This suspends Redundant Pair switching when set to 'suspended'. This has no effect when redundancy is disabled. Forced switching of Redundant Pairs is not prevented when this is set to 'suspended'. |
| apexManRteGbeInRedTable | 1.3.6.1.4.1.1166.1.31.10.1.6.3 | not-accessible | This table is the Manual Routing Gigabit Ethernet Input Transport Stream Configuration Table. This table contains 768 rows. For Force Switching a Redundancy pair for an Input TS configured in this table, refer to the same row index in apexManRteGbeInRedForceSwitchTable. Once written, the change to this table will only take immediate effect after apexManRteGbeInRedApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexManRteGbeInRedApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini') | |
| I32 apexManRteGbeInRedThreshold | 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.10 | Integer32 | read-write | Manual Routing Gigabit Ethernet Redundancy Threshold. This is the percent used to determine Fail Over from Primary to Secondary, and Switch Back from Secondary to Primary. If a value of zero is specified, Fail Over or Switch Back will not occur. Range is 0 to 100%. Primary Fail Over to Secondary: FailOver = (PrimaryRate) = (Threshold * SecondaryRate) The Primary must remain at or above the threshold for apexGbeConfInRedundMonitorPeriod seconds. The APEX will delay Switch Back an additional apexGbeConfInRedundSwitchTime seconds. Switch Back will not occur when apexManRteGbeInRedSuspend is set to 'suspended' or apexGbeConfInRedundAutoSwitchBack is 'disabled'. |
| APP apexManRtePassThroughApplyChange | 1.3.6.1.4.1.1166.1.31.10.1.4.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the row of data in the Manual Route Pass Through Table. A row in this table corresponds to the same row index in the Manual Route Pass Through table. This parameter MUST be set to 'apply' in order for any of the data in the Manual Route Pass Through Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the Manual Route Pass Through Table row has been configured. @Config(config=no, reboot=no) |
| apexManRtePassThroughApplyEntry | 1.3.6.1.4.1.1166.1.31.10.1.4.1 | not-accessible | Manual Route Apply Table Entry. | |
| I32 apexManRtePassThroughApplyOutputTsNum | 1.3.6.1.4.1.1166.1.31.10.1.4.1.1 | Integer32 | not-accessible | The index of the Manual Route Pass Through Apply Table. |
| apexManRtePassThroughApplyTable | 1.3.6.1.4.1.1166.1.31.10.1.4 | not-accessible | Table of Apply Change for the data for Manual Route Pass Through Table. A row in this table corresponds to the same row index in the Manual Route Pass Through table. | |
| ENA apexManRtePassThroughEnable | 1.3.6.1.4.1.1166.1.31.10.1.5.1.2 | EnableDisableTYPE | read-write | Indicates that this Manual Route Pass Through is enabled or disabled. An input stream can only be passed through to an output stream when there are no active service or PID mappings to the output stream. |
| apexManRtePassThroughEntry | 1.3.6.1.4.1.1166.1.31.10.1.5.1 | not-accessible | Manual Route Pass Through Table Entry. | |
| I32 apexManRtePassThroughInputInterface | 1.3.6.1.4.1.1166.1.31.10.1.5.1.4 | Integer32 | read-write | Number of the input interface, of type configured by Input Type, from which to obtain data. Range: '0' = Not Applicable GBE = 1-4 FastEnet = 1-2 |
| IP apexManRtePassThroughInputMulticastIp | 1.3.6.1.4.1.1166.1.31.10.1.5.1.6 | IpAddress | read-write | Input Multicast IP address from which to obtain data. An IP address of 0.0.0.0 indicates table entry not in use. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved. |
| IP apexManRtePassThroughInputSourceIp | 1.3.6.1.4.1.1166.1.31.10.1.5.1.7 | IpAddress | read-write | Input IGMP v3 Source IP address from which to obtain data. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address. |
| INT apexManRtePassThroughInputType | 1.3.6.1.4.1.1166.1.31.10.1.5.1.3 | INTEGER | read-write | Input Type of input from which to obtain data. |
| I32 apexManRtePassThroughInputUdp | 1.3.6.1.4.1.1166.1.31.10.1.5.1.5 | Integer32 | read-write | Input UDP Port from which to obtain data. Range: GBE = 0-65535 FastEnet = 1024-65535 |
| STR apexManRtePassThroughInvalidApplyText | 1.3.6.1.4.1.1166.1.31.10.2.1.2 | DisplayString | read-only | When apexManRtePassThroughApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a table entry that was invalid. |
| I32 apexManRtePassThroughOutputTsNum | 1.3.6.1.4.1.1166.1.31.10.1.5.1.1 | Integer32 | not-accessible | The index of the Manual Route Pass Through Table. |
| apexManRtePassThroughTable | 1.3.6.1.4.1.1166.1.31.10.1.5 | not-accessible | Table of data for Manual Route Pass Through. This table is used to pass through an entire input stream to an output stream. Once written, the change to a row this table will only take immediate effect after the appropriate apexManRtePassThroughApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexManRtePassThroughApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') | |
| APP apexManualRouteApplyChange | 1.3.6.1.4.1.1166.1.31.10.1.2.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the row of data in the Manual Route Table. A row in this table corresponds to the same row index in the Manual Route table. This parameter MUST be set to 'apply' in order for any of the data in the Manual Route Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the Manual Route Table row has been configured. @Config(config=no, reboot=no) |
| apexManualRouteApplyEntry | 1.3.6.1.4.1.1166.1.31.10.1.2.1 | not-accessible | Manual Route Apply Table Entry. | |
| I32 apexManualRouteApplyIndex | 1.3.6.1.4.1.1166.1.31.10.1.2.1.1 | Integer32 | not-accessible | The index of the Manual Route Apply Table. |
| apexManualRouteApplyTable | 1.3.6.1.4.1.1166.1.31.10.1.2 | not-accessible | Table of Apply Change for the data for Manual Route Table. A row in this table corresponds to the same row index in the Manual Route table. | |
| ENA apexManualRouteEnable | 1.3.6.1.4.1.1166.1.31.10.1.3.1.2 | EnableDisableTYPE | read-write | Indicates that this Manual Route is enabled or disabled. |
| apexManualRouteEntry | 1.3.6.1.4.1.1166.1.31.10.1.3.1 | not-accessible | Manual Route Table Entry. | |
| apexManualRouteGbeInputRedundConfig | 1.3.6.1.4.1.1166.1.31.10.1.6 | |||
| apexManualRouteGbeInputRedundStatus | 1.3.6.1.4.1.1166.1.31.10.2.2 | |||
| I32 apexManualRouteIndex | 1.3.6.1.4.1.1166.1.31.10.1.3.1.1 | Integer32 | not-accessible | The index of the Manual Route Table. |
| I32 apexManualRouteInputInterface | 1.3.6.1.4.1.1166.1.31.10.1.3.1.4 | Integer32 | read-write | Number of the input interface, of type configured by Input Type, from which to obtain data. Range: '0' = Not Applicable GBE = 1-4 FastEnet = 1-2 |
| IP apexManualRouteInputMulticastIp | 1.3.6.1.4.1.1166.1.31.10.1.3.1.6 | IpAddress | read-write | Input Multicast IP address from which to obtain data. An IP address of 0.0.0.0 indicates table entry not in use. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved. |
| ENA apexManualRouteInputPreEncryptCheck | 1.3.6.1.4.1.1166.1.31.10.1.3.1.9 | EnableDisableTYPE | read-write | Manual Routing Pre-Encryption Checking. Indicates if the APEX is to check if the input service is pre-encrypted or clear. Pre-encrypted is determined by examining the input PMT for a CA ECM descriptor (any CA ECM descriptor). If pre-encrypted, setting this flag will cause the APEX to pass through ECM PID for this service. For input services that have a GI CA ECM descriptor, the APEX will also pass through the PIT message (extract and re-insert the PIT). The output PMT for pre-encrypted services will contain a CA ECM descriptor (referencing the ECM PID). When PID Remapping is enabled, pre-encryption for a service is only valid when the input ECM PID is on a different PID than the associated PMT PID. If this flag is set to pre-encryption and the input service is not pre-encrypted, then the setting of this flag has no affect on the output service. |
| I32 apexManualRouteInputProgNum | 1.3.6.1.4.1.1166.1.31.10.1.3.1.8 | Integer32 | read-write | Input MPEG Program Number to multiplex. A value of 0 can be used as a wild card. This will cause the APEX to map the first program listed in the input PAT to the specified output (regardless of input program number). Input program number zero should only be used when mapping Single Program Transport Streams (SPTS). |
| IP apexManualRouteInputSourceIp | 1.3.6.1.4.1.1166.1.31.10.1.3.1.7 | IpAddress | read-write | Input IGMP v3 Source IP from which to obtain data. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address. |
| INT apexManualRouteInputType | 1.3.6.1.4.1.1166.1.31.10.1.3.1.3 | INTEGER | read-write | Input Type of input from which to obtain data. |
| I32 apexManualRouteInputUdp | 1.3.6.1.4.1.1166.1.31.10.1.3.1.5 | Integer32 | read-write | Input UDP Port from which to obtain data. Range: GBE = 0-65535 FastEnet = 1024-65535 |
| STR apexManualRouteInvalidApplyText | 1.3.6.1.4.1.1166.1.31.10.2.1.1 | DisplayString | read-only | When apexManualRouteApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a table entry that was invalid. |
| INT apexManualRouteOutputCopyProtectSource | 1.3.6.1.4.1.1166.1.31.10.1.3.1.13 | INTEGER | read-write | Copy Protection Source. Not supported. |
| INT apexManualRouteOutputEncryptMode | 1.3.6.1.4.1.1166.1.31.10.1.3.1.12 | INTEGER | read-write | Encryption Mode. Not supported. |
| I32 apexManualRouteOutputProgNum | 1.3.6.1.4.1.1166.1.31.10.1.3.1.11 | Integer32 | read-write | Output Program number to use for the program. Zero = NotApplicable and is only valid if the apexManualRouteTable entry is not being used. |
| I32 apexManualRouteOutputTsNum | 1.3.6.1.4.1.1166.1.31.10.1.3.1.10 | Integer32 | read-write | Output Transport Stream Number of the output on which to place data. Zero = NotApplicable and is only valid if the apexManualRouteTable entry is not being used. |
| I32 apexManualRouteProviderId | 1.3.6.1.4.1.1166.1.31.10.1.3.1.15 | Integer32 | read-write | Broadcast Encryption Provider ID. Only applies to programs if the input type is Gbe and the output encryption mode is Broadcast Encryption. (apexOutputTsConfEncryptionType set to 'broadcastEncryption') |
| APP apexManualRouteRmdClear | 1.3.6.1.4.1.1166.1.31.10.1.1.1 | ApplyDataToDeviceTYPE | read-write | Clear all RMD information from DRAM and flash. Note that apexManualRouteEnable must be set to disabled for all rows before RMD information will be cleared by this parameter. If RMD information was cleared, the APEX will set this parameter to applyNotInProgressValidData. If RMD information was not cleared, the APEX will set this parameter to applyNotInProgressInvalidData. Once written, the change to this parameter will take effect immediately. @Config(config=no, reboot=no) |
| I32 apexManualRouteSourceId | 1.3.6.1.4.1.1166.1.31.10.1.3.1.14 | Integer32 | read-write | Broadcast Encryption Source ID. Only applies to programs if the input type is Gbe and the output encryption mode is Broadcast Encryption. (apexOutputTsConfEncryptionType set to 'broadcastEncryption') |
| apexManualRouteTable | 1.3.6.1.4.1.1166.1.31.10.1.3 | not-accessible | Table of data for Manual Routes. Once written, the change to a row this table will only take immediate effect after the appropriate apexManualRouteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexManualRouteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') | |
| apexManualRouting | 1.3.6.1.4.1.1166.1.31.10 | |||
| apexManualRoutingConfig | 1.3.6.1.4.1.1166.1.31.10.1 | |||
| apexManualRoutingConfigGeneral | 1.3.6.1.4.1.1166.1.31.10.1.1 | |||
| apexManualRoutingStatus | 1.3.6.1.4.1.1166.1.31.10.2 | |||
| apexManualRoutingStatusGeneral | 1.3.6.1.4.1.1166.1.31.10.2.1 | |||
| I32 apexMappingErrorCode | 1.3.6.1.4.1.1166.1.31.200.6.1.3 | Integer32 | read-only | Error code for this mapping error. 0 indicates no error. |
| apexMappingErrorEntry | 1.3.6.1.4.1.1166.1.31.200.6.1 | not-accessible | Program, PID, Stream Pass Through Error Table Entry. | |
| I32 apexMappingErrorIndex | 1.3.6.1.4.1.1166.1.31.200.6.1.1 | Integer32 | not-accessible | Index to Program, PID, Stream Pass Through, DEPI Control, DEPI Session Error table. |
| I32 apexMappingErrorInputInterface | 1.3.6.1.4.1.1166.1.31.200.6.1.6 | Integer32 | read-only | Interface port number of the primary input interface. |
| I32 apexMappingErrorInputProgramPid | 1.3.6.1.4.1.1166.1.31.200.6.1.10 | Integer32 | read-only | For program mappings, this is the input program number of the program being mapped. For ancillary PID mappings, this is the input PID number being mapped. For stream pass through mappings, this field is not used and is set to 0. |
| INT apexMappingErrorInputType | 1.3.6.1.4.1.1166.1.31.200.6.1.5 | INTEGER | read-only | Input Type. Indicates if mapping is from Gigabit Ethernet or Fast Ethernet. |
| INT apexMappingErrorMappingType | 1.3.6.1.4.1.1166.1.31.200.6.1.4 | INTEGER | read-only | Type of mapping (program, ancillary PID, or stream pass through). |
| IP apexMappingErrorMulticastIp | 1.3.6.1.4.1.1166.1.31.200.6.1.8 | IpAddress | read-only | The Multicast receive IP address for primary input. |
| INT apexMappingErrorOutputOpMode | 1.3.6.1.4.1.1166.1.31.200.6.1.12 | INTEGER | read-only | Operating mode of the output transport stream for this mapping. |
| I32 apexMappingErrorOutputProgramPid | 1.3.6.1.4.1.1166.1.31.200.6.1.11 | Integer32 | read-only | For program mappings, this is the output program number of the program being mapped. For ancillary PID mappings, this is the output PID number being mapped. For stream pass through mappings, this field is not used and is set to 0. |
| I32 apexMappingErrorOutputTsNum | 1.3.6.1.4.1.1166.1.31.200.6.1.13 | Integer32 | read-only | The number of the output transport stream for this mapping error. |
| I32 apexMappingErrorSecInputInterface | 1.3.6.1.4.1.1166.1.31.200.6.1.14 | Integer32 | read-only | Interface port number of the secondary input interface. An interface number of 0 indicates no secondary input. |
| IP apexMappingErrorSecMulticastIp | 1.3.6.1.4.1.1166.1.31.200.6.1.16 | IpAddress | read-only | The Multicast receive IP address for secondary input. |
| IP apexMappingErrorSecSourceIp | 1.3.6.1.4.1.1166.1.31.200.6.1.17 | IpAddress | read-only | This is the IGMP v3 Source IP address of the source device for the secondary input. |
| I32 apexMappingErrorSecUdpPort | 1.3.6.1.4.1.1166.1.31.200.6.1.15 | Integer32 | read-only | Input UDP Port for secondary input. |
| IP apexMappingErrorSourceIp | 1.3.6.1.4.1.1166.1.31.200.6.1.9 | IpAddress | read-only | This is the IGMP v3 Source IP address of the source device for the primary input. |
| apexMappingErrorTable | 1.3.6.1.4.1.1166.1.31.200.6 | not-accessible | Table of program, ancillary PID, and stream pass through mapping errors that have occurred. Maximum of 100 error events will be recorded. | |
| I32 apexMappingErrorTimeLogged | 1.3.6.1.4.1.1166.1.31.200.6.1.2 | Integer32 | read-only | Time in GPS seconds (apexSystemTime) that this error was logged. |
| I32 apexMappingErrorUdpPort | 1.3.6.1.4.1.1166.1.31.200.6.1.7 | Integer32 | read-only | Input UDP Port for primary input. |
| I32 apexMaxServiceMappings | 1.3.6.1.4.1.1166.1.31.1.2.1.2 | Integer32 | read-only | Maximum number of service mappings supported by the APEX. |
| APP apexMcEmmInsertionApplyChange | 1.3.6.1.4.1.1166.1.31.1.1.2.6 | ApplyDataToDeviceTYPE | read-write | The Apply for the MediaCipher EMM Insertion group. This parameter MUST be set to 'apply' in order for any of the data in the MC EMM Insertion group to take effect in the device. This parameter MUST be set LAST after all other data in the MC Emm Insertion group has been configured. @Config(config=no, reboot=no) |
| INT apexMcEmmInsertionMode | 1.3.6.1.4.1.1166.1.31.1.1.2.1 | INTEGER | read-write | Specify the mode in which MediaCipher EMMs are inserted, out of band or full in band. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexMcEmmInsertionPid1 | 1.3.6.1.4.1.1166.1.31.1.1.2.3 | Unsigned32 | read-write | First EMM PID to include in the CAT for MediaCipher Full In Band mode. Allowed values: from 0x1C00 to 0x1FFE. Default value is 0x1C02. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexMcEmmInsertionPid1Enable | 1.3.6.1.4.1.1166.1.31.1.1.2.2 | EnableDisableTYPE | read-write | Enable/disable first EMM PID to include in the CAT for MediaCipher Full In Band mode. Default value is enabled. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexMcEmmInsertionPid2 | 1.3.6.1.4.1.1166.1.31.1.1.2.5 | Unsigned32 | read-write | Second EMM PID to include in the CAT for MediaCipher Full In Band mode. Allowed values: from 0x1C00 to 0x1FFE. Default value is 0x1C03. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexMcEmmInsertionPid2Enable | 1.3.6.1.4.1.1166.1.31.1.1.2.4 | EnableDisableTYPE | read-write | Enable/disable first EMM PID to include in the CAT for MediaCipher Full In Band mode. Default value is disabled. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| STR apexMpc2FpgaVersion | 1.3.6.1.4.1.1166.1.31.1.2.2.11 | DisplayString | read-only | APEX MPC2 FPGA Version. |
| INT apexMuxFpgaEncryption | 1.3.6.1.4.1.1166.1.31.1.2.2.3 | INTEGER | read-only | APEX MUX FPGA Encryption type currently loaded. |
| STR apexMuxFpgaVersion | 1.3.6.1.4.1.1166.1.31.1.2.2.2 | DisplayString | read-only | APEX MUX FPGA Version. |
| apexOamp | 1.3.6.1.4.1.1166.1.31.6.3 | |||
| ENA apexOampAutoNegotiate | 1.3.6.1.4.1.1166.1.31.6.3.1.1.3 | EnableDisableTYPE | read-write | OAMP IP (Enet1) Ethernet Auto-Negotiation setting. 'disabled' is not supported. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexOampConfig | 1.3.6.1.4.1.1166.1.31.6.3.1 | |||
| apexOampConfigGeneral | 1.3.6.1.4.1.1166.1.31.6.3.1.1 | |||
| INT apexOampDuplexMode | 1.3.6.1.4.1.1166.1.31.6.3.2.1.3 | INTEGER | read-only | OAMP IP (Enet1) Ethernet Duplex Mode (full or half) This is determined by the results of the auto-negotiation process. If auto-negotiation fails, the default mode is Full. |
| I32 apexOampInputTsAssignedCount | 1.3.6.1.4.1.1166.1.31.6.3.2.1.4 | Integer32 | read-only | Number of input transport streams assigned to the OAMP IP interface (Enet1). |
| IP apexOampIpAddr | 1.3.6.1.4.1.1166.1.31.6.3.1.1.1 | IpAddress | read-write | This is the IP address of the OAMP IP (Enet1) interface of the APEX. This IP address is set via a BootP when connected to a Bootp server. When not connected to a BootP server, the IP address may directly be changed by setting this parameter. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ACT apexOampLinkActive | 1.3.6.1.4.1.1166.1.31.6.3.2.1.5 | ActiveTYPE | read-only | This indicates if the OAMP (ENET1) link is active. |
| STR apexOampMacAddr | 1.3.6.1.4.1.1166.1.31.6.3.2.1.1 | DisplayString | read-only | This is the MAC address of the APEX OAMP IP (Enet1) Interface. It is set at the factory and cannot be changed. The string length is 17 characters in the format 'hh:hh:hh:hh:hh:hh' where 'hh' is a hexadecimal number. |
| INT apexOampSpeed | 1.3.6.1.4.1.1166.1.31.6.3.2.1.2 | INTEGER | read-only | OAMP IP (Enet1) Ethernet speed (10Mbps or 100Mbps). This is determined by the results of the auto-negotiation process. If auto-negotiation fails, the default speed is 100Mbps. |
| apexOampStatus | 1.3.6.1.4.1.1166.1.31.6.3.2 | |||
| apexOampStatusGeneral | 1.3.6.1.4.1.1166.1.31.6.3.2.1 | |||
| IP apexOampSubnetMask | 1.3.6.1.4.1.1166.1.31.6.3.1.1.2 | IpAddress | read-write | This is subnet mask of the OAMP IP (Enet1) interface of the APEX. The subnet mask is normally via a BootP when connected to a BootP server. When not connected to a Bootp Server, the Subnet Mask may directly be changed by setting this parameter. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexOperationalTime | 1.3.6.1.4.1.1166.1.31.2.2.1.8 | Integer32 | read-only | The Operational Time is the time in seconds since the APEX completed the boot sequence. It is the time that the APEX has been operational. |
| apexOutputProgram | 1.3.6.1.4.1.1166.1.31.16 | |||
| INT apexOutputProgramApsLevel | 1.3.6.1.4.1.1166.1.31.16.2.2.1.13 | INTEGER | read-only | Copy protection Analog Protection Services Level. This is only applicable when the program is being encrypted. |
| INT apexOutputProgramCciLevel | 1.3.6.1.4.1.1166.1.31.16.2.2.1.12 | INTEGER | read-only | Copy protection CCI Level. This is only applicable when the program is being encrypted. |
| INT apexOutputProgramCitSetting | 1.3.6.1.4.1.1166.1.31.16.2.2.1.14 | INTEGER | read-only | Copy protection Constraint Image Trigger setting. This is only applicable when the program is being encrypted. |
| apexOutputProgramConfig | 1.3.6.1.4.1.1166.1.31.16.1 | |||
| apexOutputProgramConfigGeneral | 1.3.6.1.4.1.1166.1.31.16.1.1 | |||
| INT apexOutputProgramDtaEncryptionMode | 1.3.6.1.4.1.1166.1.31.16.2.2.1.20 | INTEGER | read-only | This parameter identifies whether a service in Full Encryption is in Modified Privacy Mode (DTA) and whether the DTA service has CCM messages. This parameter is applicable only when apexOutputProgramEncryptionMode is 'full'. In other encryption modes this value is ignored. notApplicable - Non DTA Service and/or No DTA CA descriptor found dtaWithCcm - DTA, Full Encryption, Modified Privacy Mode, CCM present dtaWithoutCcm - DTA, Full Encryption, Modified Privacy Mode, CCM absent. |
| I32 apexOutputProgramEcmServiceId | 1.3.6.1.4.1.1166.1.31.16.2.2.1.11 | Integer32 | read-only | The ECM service ID used when this program is encrypted. This is the service ID used in all ECM messages for this program. |
| INT apexOutputProgramEncryptionMode | 1.3.6.1.4.1.1166.1.31.16.2.2.1.9 | INTEGER | read-only | Currently configured encryption mode for the program. none - indicates the program is not being encrypted for CTE or Broadcast encryption. unencrypted - Applies to Broadcast services only. Unencrypted services are treated the same as clear services (no encryption). preEncrypted - Applies to Broadcast services only. Input program pre-encryption checking is applied. Output program is not encrypted by the APEX, regardless if input encrypted or not. unencryptedWithCci - True unencrypted mode where packets are not scrambled, but ECMs are inserted and ECM CA reference is added to output PMT (PRK contains Copy Protection information). |
| STR apexOutputProgramEncryptionStatus | 1.3.6.1.4.1.1166.1.31.16.2.2.1.10 | DisplayString | read-only | Current Program Encryption Status. |
| apexOutputProgramEntry | 1.3.6.1.4.1.1166.1.31.16.2.2.1 | not-accessible | Output Program Table Entry. | |
| INT apexOutputProgramError | 1.3.6.1.4.1.1166.1.31.16.2.2.1.8 | INTEGER | read-only | Indicates if the program is in error. |
| I32 apexOutputProgramIndex | 1.3.6.1.4.1.1166.1.31.16.2.2.1.1 | Integer32 | not-accessible | Output Program Table Index. |
| INT apexOutputProgramInputPreEncrypted | 1.3.6.1.4.1.1166.1.31.16.2.2.1.6 | INTEGER | read-only | Indicates whether the program was pre-encrypted. Pre-encryption status is determined by the presence or absence of a CA ECM descriptor within the input PMT. |
| I32 apexOutputProgramInputProgNum | 1.3.6.1.4.1.1166.1.31.16.2.2.1.3 | Integer32 | read-only | Input MPEG Program Number. |
| I32 apexOutputProgramInputTsIndex | 1.3.6.1.4.1.1166.1.31.16.2.2.1.2 | Integer32 | read-only | The index into the apexInputTsStatTable. |
| I32 apexOutputProgramNumberTiers | 1.3.6.1.4.1.1166.1.31.16.2.2.1.15 | Integer32 | read-only | The number of program tiers. This is only applicable when the program is being encrypted. |
| I32 apexOutputProgramOutputProgNum | 1.3.6.1.4.1.1166.1.31.16.2.2.1.4 | Integer32 | read-only | Output MPEG Program Number. |
| I32 apexOutputProgramOutputTsNum | 1.3.6.1.4.1.1166.1.31.16.2.2.1.7 | Integer32 | read-only | Output Transport Stream Number. |
| INT apexOutputProgramProgramType | 1.3.6.1.4.1.1166.1.31.16.2.2.1.19 | INTEGER | read-only | Indicates how programs are to be built by the encryptor. 1 - programsDerived (default) - programs are derived where the encryptor builds the programs internally for the specified service. The program related ECM messages and program name/info messages are derived from the service RMD data and internal schedules. This program type is typically used for subscription services. 2 - programInfoProvided - the encryptor should build the programs based on the program information provided by the controller via the element of the ServiceProgramReply payload. The service RMD data is still used to generate the program related ECM messages. 3 - programEcmProvided - the encryptor should use pre-built ECM program messages as provided by the controller via the element of the ServiceProgramReply payload. For this program type, the controller provides the schedules; however, the encryptor must default much of the program info message since not detailed program information is provided. DTA content protection encryption makes use of the 'programEcmProvided' program type since the ECM messages cannot be derived by the encryptor. 4 - programInfoAndEcmProvided - the encryptor should build the programs based on both the program information and pre-built ECM messages provided by the controller via the and elements of the ServiceProgramReply payload. |
| I32 apexOutputProgramProviderId | 1.3.6.1.4.1.1166.1.31.16.2.2.1.18 | Integer32 | read-only | Broadcast Encryption Provider ID. Only applies to programs when the input type is Gbe and the output encryption mode is Broadcast Encryption. (apexOutputTsConfEncryptionType set to 'broadcastEncryption') |
| STR apexOutputProgramRoutingStatus | 1.3.6.1.4.1.1166.1.31.16.2.2.1.5 | DisplayString | read-only | Current Program Routing Status. |
| I32 apexOutputProgramSourceId | 1.3.6.1.4.1.1166.1.31.16.2.2.1.17 | Integer32 | read-only | Broadcast Encryption Source ID. Only applies to programs when the input type is Gbe and the output encryption mode is Broadcast Encryption. (apexOutputTsConfEncryptionType set to 'broadcastEncryption') |
| apexOutputProgramStatus | 1.3.6.1.4.1.1166.1.31.16.2 | |||
| apexOutputProgramStatusGeneral | 1.3.6.1.4.1.1166.1.31.16.2.1 | |||
| apexOutputProgramTable | 1.3.6.1.4.1.1166.1.31.16.2.2 | not-accessible | This table shows the input program to output program mapping status. | |
| STR apexOutputProgramTierData | 1.3.6.1.4.1.1166.1.31.16.2.2.1.16 | DisplayString | read-only | Current Program Tier Data. Tier information is in hexadecimal format. Up to 7 tiers of information are provided for each program. Tier information for each program consists of 8 bytes of information. First 4 bytes are the program tier value in hexadecimal. Next 4 bytes are the tier type in hexadecimal format. This is only applicable when the program is being encrypted. |
| apexOutputTransport | 1.3.6.1.4.1.1166.1.31.14 | |||
| APP apexOutputTsConfApplyChange | 1.3.6.1.4.1.1166.1.31.14.1.5.1.2 | ApplyDataToDeviceTYPE | read-write | The apply for Output Ts Config Table. This apply is only used for apexOutputTsConfOperatingMode, apexOutputTsConfEncryptionType, and apexOutputTsConfSimulcryptMode. A row in this table corresponds to the same row index in the Output Ts Config table. This parameter MUST be set to 'apply' in order for the items listed above to take effect in the APEX. This parameter MUST be set LAST after the relevant data in the Output Ts Config row has been configured. @Config(config=no, reboot=no) |
| apexOutputTsConfApplyEntry | 1.3.6.1.4.1.1166.1.31.14.1.5.1 | not-accessible | Output Transport Stream Apply Table Entry. | |
| I32 apexOutputTsConfApplyIndex | 1.3.6.1.4.1.1166.1.31.14.1.5.1.1 | Integer32 | not-accessible | Index of Output Transport Stream Apply Table. |
| apexOutputTsConfApplyTable | 1.3.6.1.4.1.1166.1.31.14.1.5 | not-accessible | Table of Apply Change for Output Ts Config Table. This apply is only used for apexOutputTsConfOperatingMode, apexOutputTsConfEncryptionType, and apexOutputTsConfSimulcryptMode. | |
| INT apexOutputTsConfEncryptionType | 1.3.6.1.4.1.1166.1.31.14.1.6.1.6 | INTEGER | read-write | This parameter is used to set the encryption type of the output. 'noEncryption' - All services are output in the clear 'cte' - Services on output use Common Tier Encryption. CTE parameters determine encryption mode, copy protection, and tiers. All services in CTE mode use the exact same configuration settings. - Valid for all operating modes - Simulcrypt Mode must be set to None 'broadcastEncryption' - Services on output use Broadcast Encryption. Requires connection to RDS (DAC) to get EMMs and Rights Meta Data (tiers, encryption mode, and copy protection settings) for each individual service. - Only valid when Operating Mode is Manual Routing. - Simulcrypt Mode must be set to None @Commit(param=apexOutputTsConfApplyChange, value=2) |
| apexOutputTsConfig | 1.3.6.1.4.1.1166.1.31.14.1 | |||
| apexOutputTsConfigEntry | 1.3.6.1.4.1.1166.1.31.14.1.6.1 | not-accessible | Output Transport Stream Configuration Table Entry. | |
| apexOutputTsConfigGeneral | 1.3.6.1.4.1.1166.1.31.14.1.1 | |||
| apexOutputTsConfigTable | 1.3.6.1.4.1.1166.1.31.14.1.6 | not-accessible | This is a table of configuration parameters for Output Transport Streams. Once written, a change to apexOutputTsConfEncryptionType, apexOutputTsConfOperatingMode, or apexOutputTsConfSimulcryptMode will only take immediate effect after the appropriate apexOutputTsConfApplyChange is set to 'apply'. All other changes to this table will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| INT apexOutputTsConfOperatingMode | 1.3.6.1.4.1.1166.1.31.14.1.6.1.3 | INTEGER | read-write | This parameter is used to set the operating mode of the output. Operating mode changes can only occur when the output is not in use (no service, PID, or stream mapping active to the output). Session Control - User must select either RTSP or RPC to communicate with external resource manager. All service mappings on output are controlled by the external manager. - Only valid when Encryption Type is set to CTE or None - Only valid when Simulcrypt Mode is set to None - PID Remapping mode should be Enabled (Without Reuse) Manual Routing - User manually maps each service - Encryption Type can be any valid setting (none, CTE, or Broadcast) - Simulcrypt Mode must be None or External EIS UDP Port Mapping - Standard UDP Port Mapping for use with VOD servers. Uses specific algorithm based on UDP Port to determine output program mappings. - Encryption Type must be None or CTE (broadcast not supported) - Simulcrypt Mode must be None or External EIS Operating mode changes can only occur when the output is not in use (no service, PID, or stream mapping active to the output). @Commit(param=apexOutputTsConfApplyChange, value=2) |
| I32 apexOutputTsConfOutPatTsId | 1.3.6.1.4.1.1166.1.31.14.1.6.1.4 | Integer32 | read-write | Output Transport Stream ID to use for the output PAT in this Output Transport Stream. Changes to the output PAT TS ID can be made at any time and will cause the output PAT to automatically be updated to reflect the new TS ID setting. |
| I32 apexOutputTsConfOutputTsNum | 1.3.6.1.4.1.1166.1.31.14.1.6.1.1 | Integer32 | not-accessible | Output Transport Stream Number. |
| ENA apexOutputTsConfPcrLess | 1.3.6.1.4.1.1166.1.31.14.1.6.1.8 | EnableDisableTYPE | read-write | This parameter indicates that PCR-less is enabled for the Output Transport Stream. |
| INT apexOutputTsConfPidRemappingMode | 1.3.6.1.4.1.1166.1.31.14.1.6.1.2 | INTEGER | read-write | The PID Remapping mode setting. When 'disabled', the output PIDs for all services and ancillary PIDs are the same as the input PID values. This scheme can only be used when either mapping an entire MPTS to a QAM output or when SPTS are mapped and the user has already ensured that all of the PIDs across all inputs mapped to the same output stream are unique. When 'remapWithoutReuse', the APEX will determine the output PIDs from a predetermined range of PIDs for services and ancillary PIDs. The APEX will use a scheme to limit the reuse of service PIDs for each service mapping. This scheme MUST be used for outputs in Session Control mode and in normally in UDP Port Mapping mode (exception noted below). When receiving SPTS inputs, in order to ensure there are no PID conflicts, this scheme should be selected. When 'remapProgramBased', the APEX will determine the output PIDs from a predetermined range of PIDs for services and ancillary PIDs. The APEX uses a scheme to select the PMT PID based on the program number. The PMT PID is calculated as follows: (Program Number + 1) * 16. The component PIDs are sequential after the PMT PID. This scheme only allows for a total of 15 component PIDs per program. Output program numbers are also limited (1-256). This scheme is intended to be used when in UDP Port Mapping mode at specific sites. When 'unrestricted', the APEX will allocate output PIDs as long as they are needed using the whole available PIDs range, unlike other pid-remapping modes where PID values are internally pre-allocated for different uses (PMT, components, ECM, ...). This scheme is only recommended for cases when the user need a special pre-assigned EMM pid that can't be configured in the other pid-remapping modes. PID Remapping mode changes can only occur when the output is not in use (no service, PID, or stream mapping active to the output). |
| ENA apexOutputTsConfPsipEnable | 1.3.6.1.4.1.1166.1.31.14.1.6.1.5 | EnableDisableTYPE | read-write | This parameter indicates that PSIP is enabled for the Output Transport Stream. |
| INT apexOutputTsConfSimulcryptMode | 1.3.6.1.4.1.1166.1.31.14.1.6.1.7 | INTEGER | read-write | This parameter is used to set the Simulcrypt mode of the output. The actual behavior is disable/enable (none/externalEIS). It can be set to externalEIS if the Encryption Algorithm is set to 'dvb-csa-simulcrypt and the Operating Mode is set to 'ManualRouting' or 'udpMapping'. It only can be none if there are no SCGs provisioned on that output TS. 'none' - Used for normal Mediacypher only encryption (CTE or Broadcast Encryption). 'externalEIS' - Used to indicate an external EIS can control the encryption of all services on the output. - Only valid when: - Operating Mode is set to 'ManualRouting' or 'udpMapping' - Encryption Algorithm is set to 'dvb-csa-simulcrypt' 'internalEIS' - Not supported at this time and is invalid to select. @Commit(param=apexOutputTsConfApplyChange, value=2) |
| I32 apexOutputTsEventAlarmCode | 1.3.6.1.4.1.1166.1.31.200.3.1.3 | Integer32 | read-only | Last number of alarm OID. Can be one of the following: 0 Indicates event is informational and may or may not cause an alarm. 8040 apexAlarmOutputUtilizationFault 8041 apexAlarmOutputOverflow More details about the error can be found in apexOutputTsEventDescription. |
| INT apexOutputTsEventAlarmSeverity | 1.3.6.1.4.1.1166.1.31.200.3.1.4 | INTEGER | read-only | Alarm severity level of this event. |
| I32 apexOutputTsEventAvgRate | 1.3.6.1.4.1.1166.1.31.200.3.1.7 | Integer32 | read-only | Value of apexOutputTsUtilizAvgRate when event occurred. |
| I32 apexOutputTsEventCurDropPackets | 1.3.6.1.4.1.1166.1.31.200.3.1.10 | Integer32 | read-only | Value of apexOutputTsUtilizCurDropPackets when event occurred. |
| I32 apexOutputTsEventCurRate | 1.3.6.1.4.1.1166.1.31.200.3.1.6 | Integer32 | read-only | Value of apexOutputTsUtilizCurRate when event occurred. |
| STR apexOutputTsEventDescription | 1.3.6.1.4.1.1166.1.31.200.3.1.14 | DisplayString | read-only | Text description of the event. Maximum length is 128 characters. |
| apexOutputTsEventEntry | 1.3.6.1.4.1.1166.1.31.200.3.1 | not-accessible | Output Stream Error Table Entry. | |
| I32 apexOutputTsEventIndex | 1.3.6.1.4.1.1166.1.31.200.3.1.1 | Integer32 | not-accessible | Index to Output Stream Error table. |
| I32 apexOutputTsEventMinRate | 1.3.6.1.4.1.1166.1.31.200.3.1.8 | Integer32 | read-only | Value of apexOutputTsUtilizMinRate when event occurred. |
| I32 apexOutputTsEventOutputTsNum | 1.3.6.1.4.1.1166.1.31.200.3.1.5 | Integer32 | read-only | The number of the output transport stream for this event. |
| I32 apexOutputTsEventPeakDropPackets | 1.3.6.1.4.1.1166.1.31.200.3.1.11 | Integer32 | read-only | Value of apexOutputTsUtilizPeakDropPackets when event occurred. |
| I32 apexOutputTsEventPeakRate | 1.3.6.1.4.1.1166.1.31.200.3.1.9 | Integer32 | read-only | Value of apexOutputTsUtilizPeakRate when event occurred. |
| I32 apexOutputTsEventRollingDropPackets | 1.3.6.1.4.1.1166.1.31.200.3.1.12 | Integer32 | read-only | Value of apexOutputTsUtilizRollingDropPackets when event occurred. |
| apexOutputTsEventTable | 1.3.6.1.4.1.1166.1.31.200.3 | not-accessible | Table of Output Stream events that have occurred. Maximum of 200 events will be recorded. | |
| I32 apexOutputTsEventTimeLogged | 1.3.6.1.4.1.1166.1.31.200.3.1.2 | Integer32 | read-only | Time in GPS seconds (apexSystemTime) that this event was logged. |
| I32 apexOutputTsEventTotalDropPackets | 1.3.6.1.4.1.1166.1.31.200.3.1.13 | Integer32 | read-only | Value of apexOutputTsUtilizTotalDropPackets when event occurred. |
| apexOutputTsStatus | 1.3.6.1.4.1.1166.1.31.14.2 | |||
| I32 apexOutputTsStatusAncillaryPidsMapped | 1.3.6.1.4.1.1166.1.31.14.2.5.1.4 | Integer32 | read-only | Number of ancillary PIDs currently mapped to the output. |
| I32 apexOutputTsStatusDepiSessionsMapped | 1.3.6.1.4.1.1166.1.31.14.2.5.1.8 | Integer32 | read-only | Number of DEPI sessions currently mapped to the output. |
| apexOutputTsStatusEntry | 1.3.6.1.4.1.1166.1.31.14.2.5.1 | not-accessible | A row in the Output Transport Stream Status table. | |
| INT apexOutputTsStatusFault | 1.3.6.1.4.1.1166.1.31.14.2.5.1.6 | INTEGER | read-only | Highest current fault condition associated with this Output Transport Stream. The following Alarms are included: - apexAlarmOutputOverflow - apexAlarmOutputUtilizationFault - apexAlarmQamModuleFault - apexAlarmQamRfPortFault - apexAlarmQamChannelFault |
| apexOutputTsStatusGeneral | 1.3.6.1.4.1.1166.1.31.14.2.1 | |||
| I32 apexOutputTsStatusInputStreamsMapped | 1.3.6.1.4.1.1166.1.31.14.2.5.1.5 | Integer32 | read-only | Number of input streams currently mapped to the output. |
| STR apexOutputTsStatusInvalidApplyText | 1.3.6.1.4.1.1166.1.31.14.2.1.1 | DisplayString | read-only | When apexOutputTsConfApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid. |
| I32 apexOutputTsStatusMessageGenerationNum | 1.3.6.1.4.1.1166.1.31.14.2.5.1.9 | Integer32 | read-only | Number of messages generated (DVB tables) currently in the output. |
| I32 apexOutputTsStatusOutputTsNum | 1.3.6.1.4.1.1166.1.31.14.2.5.1.1 | Integer32 | not-accessible | Output Transport Stream Number. |
| I32 apexOutputTsStatusProgramsPerTs | 1.3.6.1.4.1.1166.1.31.14.2.5.1.2 | Integer32 | read-only | Number of Output Programs supported on this Output Transport Stream. |
| I32 apexOutputTsStatusScgsProvisioned | 1.3.6.1.4.1.1166.1.31.14.2.5.1.10 | Integer32 | read-only | Number of SCGs provisioned currently in the output. |
| I32 apexOutputTsStatusServicesInError | 1.3.6.1.4.1.1166.1.31.14.2.5.1.7 | Integer32 | read-only | Number of services in error mapped to the output stream. |
| I32 apexOutputTsStatusServicesMapped | 1.3.6.1.4.1.1166.1.31.14.2.5.1.3 | Integer32 | read-only | Number of services currently mapped to the output. |
| I32 apexOutputTsStatusServicesMuxed | 1.3.6.1.4.1.1166.1.31.14.2.5.1.11 | Integer32 | read-only | Number of services successfully multiplexed. |
| apexOutputTsStatusTable | 1.3.6.1.4.1.1166.1.31.14.2.5 | not-accessible | Table of Output Transport Status. Indexed by Output Transport Stream number. | |
| apexOutputTsUtilization | 1.3.6.1.4.1.1166.1.31.14.2.2 | |||
| apexOutputTsUtilizationEntry | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1 | not-accessible | Output Transport Stream Bandwidth Utilization Table Entry. | |
| apexOutputTsUtilizationGeneral | 1.3.6.1.4.1.1166.1.31.14.2.2.1 | |||
| apexOutputTsUtilizationMonitorEntry | 1.3.6.1.4.1.1166.1.31.14.1.4.2.1 | not-accessible | Output Transport Rate Monitoring Configuration Table Entry. | |
| apexOutputTsUtilizationMonitorGeneral | 1.3.6.1.4.1.1166.1.31.14.1.4.1 | |||
| apexOutputTsUtilizationMonitoring | 1.3.6.1.4.1.1166.1.31.14.1.4 | |||
| apexOutputTsUtilizationMonitorTable | 1.3.6.1.4.1.1166.1.31.14.1.4.2 | not-accessible | This is a table of configuration parameters for Rate Monitoring of the Output Transport Stream Bandwidth Utilization. Utilization information is accessed via apexOutputTsUtilizationTable. | |
| I32 apexOutputTsUtilizationSamplePeriod | 1.3.6.1.4.1.1166.1.31.14.2.2.1.1 | Integer32 | read-only | Sample Period for Output Transport Stream Bandwidth Utilization Rate Monitoring. This parameter indicates the length of time in milliseconds the stream is monitored during a single sample. This can be used with apexOutputTsUtilizNumSamples to determine the amount of time or percent of time the stream was monitored during a fifteen minute sampling interval. |
| apexOutputTsUtilizationTable | 1.3.6.1.4.1.1166.1.31.14.2.2.2 | not-accessible | This is a table of status parameters containing bandwidth utilization for Output Transport Streams. The sampling interval is up to fifteen minutes. There is a rolling average as well as last sample, peak, and minimum information. There is overflow information and dropped packet counts. This table is indexed by Output Transport Stream Number. | |
| I32 apexOutputTsUtilizAvgPercent | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.7 | Integer32 | read-only | Average percent utilization over the rolling sampling interval. |
| U32 apexOutputTsUtilizAvgRate | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.11 | Unsigned32 | read-only | Average utilization for the rolling sampling interval in bits per second (bps). |
| U32 apexOutputTsUtilizCurDropPackets | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.15 | Unsigned32 | read-only | MPEG packets dropped during the most recently taken sample. |
| I32 apexOutputTsUtilizCurPercent | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.6 | Integer32 | read-only | Percent utilization of most recently taken sample. |
| U32 apexOutputTsUtilizCurRate | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.10 | Unsigned32 | read-only | Utilization of most recently taken sample in bits per second (bps). |
| INT apexOutputTsUtilizDataFlag | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.2 | INTEGER | read-only | Flag to indicate whether the Output Transport Stream was monitored a full fifteen minute sampling interval and a complete set of samples was obtained. 'samplingComplete' - indicates sampling complete with good samples. 'samplingIncomplete' - indicates incomplete sampling due to APEX startup or OTS rate changed during the period. |
| I32 apexOutputTsUtilizMinPercent | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.8 | Integer32 | read-only | Minimum percent utilization for a sample during the rolling sampling interval. |
| U32 apexOutputTsUtilizMinRate | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.12 | Unsigned32 | read-only | Minimum utilization for a sample during this sampling interval in bits per second (bps). |
| U32 apexOutputTsUtilizNumSamples | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.3 | Unsigned32 | read-only | Number of samples included in the data. This can be used with apexOutputTsUtilizationSamplePeriod to determine the amount of time or percent of time the stream was monitored during the sampling interval. |
| I32 apexOutputTsUtilizOutpuTsNum | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.1 | Integer32 | not-accessible | Output Transport Stream Number. |
| INT apexOutputTsUtilizOverflow | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.14 | INTEGER | read-only | Indicates whether an overflow error has occurred. This field will clear if the output has no overflows. This field is also cleared when the QAM output is disabled. |
| INT apexOutputTsUtilizOverflowAlarm | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.20 | INTEGER | read-only | Current fault condition of apexOutputTsUtilizOverflow. This is the apexAlarmOutputOverflow level for this output. |
| U32 apexOutputTsUtilizPeakDropPackets | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.16 | Unsigned32 | read-only | Peak MPEG packets dropped for a sample during the rolling sampling interval. |
| I32 apexOutputTsUtilizPeakPercent | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.9 | Integer32 | read-only | Peak percent utilization for a sample during the rolling sampling interval. |
| U32 apexOutputTsUtilizPeakRate | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.13 | Unsigned32 | read-only | Peak utilization for a sample during the rolling sampling interval in bits per second (bps). |
| U32 apexOutputTsUtilizRollingDropPackets | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.17 | Unsigned32 | read-only | Total MPEG packets dropped during the rolling sampling interval. |
| INT apexOutputTsUtilizThreshold | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.4 | INTEGER | read-only | Indicates whether there is a utilization error has occurred. The error occurs when Output Utilization Alarm Threshold has been reached for Output Utilization Set Alarm Delay seconds and will clear after the output is below the Output Utilization Alarm Threshold for Output Utilization Clear Alarm Delay. This field is also cleared when the QAM output is disabled. |
| INT apexOutputTsUtilizThresholdAlarm | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.19 | INTEGER | read-only | Current fault condition of apexOutputTsUtilizThreshold. This is the apexAlarmOutputUtilizationFault level for this output. |
| U32 apexOutputTsUtilizTime | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.5 | Unsigned32 | read-only | Time in GPS seconds (apexSystemTime) that this table row was saved. When GPS time is not available to the apex (apexSystemTime=0) a clock maintained inside the APEX will be used. This clock starts at GPS time zero when the apex is booted. The APEX will use real GPS time if and when GPS time becomes available to the APEX. |
| U32 apexOutputTsUtilizTotalDropPackets | 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.18 | Unsigned32 | read-only | Total MPEG packets dropped on the QAM Output. Can be reset using apexOutputTsUtilMonResetTotDropPacket. |
| I32 apexOutputTsUtilMonAlarmThreshold | 1.3.6.1.4.1.1166.1.31.14.1.4.1.1 | Integer32 | read-write | The threshold, in percent, used to produce the apexAlarmOutputUtilizationFault alarm 'minor' while monitoring Output Transport Stream Bandwidth Utilization. An alarm of 'minor' will occur when this threshold is met or exceeded for apexOutputTsUtilMonSetAlarmDelay. The alarm will clear after remaining below this threshold for apexOutputTsUtilMonClearAlarmDelay. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexOutputTsUtilMonClearAlarmDelay | 1.3.6.1.4.1.1166.1.31.14.1.4.1.3 | Integer32 | read-write | This is the time in seconds that the Output Transport Stream must be below apexOutputTsUtilMonAlarmThreshold before clearing the apexAlarmOutputUtilizationFault alarm. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexOutputTsUtilMonOutputTsNum | 1.3.6.1.4.1.1166.1.31.14.1.4.2.1.1 | Integer32 | not-accessible | Output Transport Stream Number. |
| RES apexOutputTsUtilMonResetTotDropPacket | 1.3.6.1.4.1.1166.1.31.14.1.4.2.1.2 | ResetStatisticsTYPE | read-write | Output Ts Reset total dropped packets. Setting to 'reset' resets same apexOutputTsUtilizTotalDropPackets index row in apexOutputTsUtilizationTable. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| I32 apexOutputTsUtilMonSetAlarmDelay | 1.3.6.1.4.1.1166.1.31.14.1.4.1.2 | Integer32 | read-write | This is the time in seconds that the Output Transport Stream must be at or exceeding apexOutputTsUtilMonAlarmThreshold before setting the apexAlarmOutputUtilizationFault alarm. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexPatVersionIncrement | 1.3.6.1.4.1.1166.1.31.15.1.1.5 | Integer32 | read-write | Increment of PAT version upon reboot. Used to force the APEX to use a different PAT version number upon rebooting. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| APP apexPidMapApplyChange | 1.3.6.1.4.1.1166.1.31.11.1.2.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the row of data in the PID Map Table. A row in this table corresponds to the same row index in the PID Map table. This parameter MUST be set to 'apply' in order for any of the data in the PID Map Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the PID Map Table row has been configured. @Config(config=no, reboot=no) |
| apexPidMapApplyEntry | 1.3.6.1.4.1.1166.1.31.11.1.2.1 | not-accessible | PID Map Apply Table Entry. | |
| I32 apexPidMapApplyIndex | 1.3.6.1.4.1.1166.1.31.11.1.2.1.1 | Integer32 | not-accessible | The index of the PID Map Apply Table. |
| apexPidMapApplyTable | 1.3.6.1.4.1.1166.1.31.11.1.2 | not-accessible | Table of Apply Change for the data for PID Map Table. A row in this table corresponds to the same row index in the PID Map table. | |
| apexPidMapConfig | 1.3.6.1.4.1.1166.1.31.11.1 | |||
| ENA apexPidMapEnable | 1.3.6.1.4.1.1166.1.31.11.1.1.1.2 | EnableDisableTYPE | read-write | Indicates whether this PID Mapping is enabled or disabled. |
| apexPidMapEntry | 1.3.6.1.4.1.1166.1.31.11.1.1.1 | not-accessible | Pid Mapping Table Entry. | |
| I32 apexPidMapIndex | 1.3.6.1.4.1.1166.1.31.11.1.1.1.1 | Integer32 | not-accessible | Index of Pid Mapping Table. |
| I32 apexPidMapInputInterface | 1.3.6.1.4.1.1166.1.31.11.1.1.1.4 | Integer32 | read-write | Number of the input, of type configured by Input Type, from which to obtain data. Range: '0' = Not Applicable GBE = 1-4 FastEnet = 1-2 |
| IP apexPidMapInputMulticastIp | 1.3.6.1.4.1.1166.1.31.11.1.1.1.6 | IpAddress | read-write | The Multicast receive IP address on which to receive data. An IP address of 0.0.0.0 indicates singlecast only. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved. |
| I32 apexPidMapInputPid | 1.3.6.1.4.1.1166.1.31.11.1.1.1.8 | Integer32 | read-write | Input MPEG PID to multiplex. When PID Remapping for an output is enabled, the input PID value and output PID value can be different. When PID Remapping for an output is disabled, the input and output PIDs must be the same. Input PID 0 (PAT PID) cannot be mapped by the user. |
| IP apexPidMapInputSourceIp | 1.3.6.1.4.1.1166.1.31.11.1.1.1.7 | IpAddress | read-write | This is the IP address of the source device. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address. |
| INT apexPidMapInputType | 1.3.6.1.4.1.1166.1.31.11.1.1.1.3 | INTEGER | read-write | Input Type of input from which to obtain data. |
| I32 apexPidMapInputUdp | 1.3.6.1.4.1.1166.1.31.11.1.1.1.5 | Integer32 | read-write | Input UDP Port from which to obtain data. Range: GBE = 0-65535 FastEnet = 1024-65535 |
| STR apexPidMapInvalidApplyText | 1.3.6.1.4.1.1166.1.31.11.2.1.3 | DisplayString | read-only | When apexPidMapApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a table entry that was invalid. |
| I32 apexPidMapMaxPidMappings | 1.3.6.1.4.1.1166.1.31.11.2.1.1 | Integer32 | read-only | Maximum number of Ancillary PID mappings supported. |
| I32 apexPidMapOutputPid | 1.3.6.1.4.1.1166.1.31.11.1.1.1.10 | Integer32 | read-write | Output PID to use for the data. This output PID value must match the input PID value when PID Remapping for the output stream is disabled. Zero is only valid if the apexPidMapTable entry is not being used. |
| I32 apexPidMapOutputTsNum | 1.3.6.1.4.1.1166.1.31.11.1.1.1.9 | Integer32 | read-write | Output Transport Stream Number of the output on which to place data. Zero is only valid if the apexPidMapTable entry is not being used. |
| apexPidMapStatus | 1.3.6.1.4.1.1166.1.31.11.2 | |||
| apexPidMapStatusGeneral | 1.3.6.1.4.1.1166.1.31.11.2.1 | |||
| apexPidMapTable | 1.3.6.1.4.1.1166.1.31.11.1.1 | not-accessible | Table of data for Ancillary Pid Mapping. There are 480 rows in this table (APEX supports up to 480 ancillary PID mappings). Once written, the change to this table will only take immediate effect after apexPidMapApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexPidMapApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') | |
| I32 apexPmtVersionIncrement | 1.3.6.1.4.1.1166.1.31.15.1.1.6 | Integer32 | read-write | Increment of PMT version upon reboot. Used to force the APEX to use a different PMT version number upon rebooting. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexPowerSupply | 1.3.6.1.4.1.1166.1.31.4 | |||
| apexPreencryption | 1.3.6.1.4.1.1166.1.31.26 | |||
| apexPreencryptionConfig | 1.3.6.1.4.1.1166.1.31.26.1 | |||
| apexPreencryptionConfigGeneral | 1.3.6.1.4.1.1166.1.31.26.1.1 | |||
| STR apexProductName | 1.3.6.1.4.1.1166.1.31.1.1.1.2 | DisplayString | read-write | This is the Product Name of the APEX loaded at initialization from the config.ini file. Specific configurations of the APEX have specific purposes and are identified by their product name. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2, default=yes) @File(config.ini, type='ini') |
| INT apexProductType | 1.3.6.1.4.1.1166.1.31.1.2.2.6 | INTEGER | read-only | APEX Product Type. The corresponding product name text setting can be found in identUnitModel. |
| I32 apexProgramBasedPmtOffset | 1.3.6.1.4.1.1166.1.31.15.1.1.9 | Integer32 | read-write | Program Based PID Remapping PMT PID offset. Determines the first PMT PID to use when Program Based algorithm selected. PMT PID is calculated as: (Program Number + Offset) * 16 Program Numbers can range from 1 - 255, allowing for PMTs to start at 0x0020 or 0x0030 up to 0x1000 and 0x1010. Changes to offset will NOT require a reboot, but if there are any service mappings already in use on an output in Program Based mode, then the change will NOT take effect and the user will have to remove all mappings on outputs in Program Based mode. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexPsConfig | 1.3.6.1.4.1.1166.1.31.4.1 | |||
| apexPsConfigGeneral | 1.3.6.1.4.1.1166.1.31.4.1.1 | |||
| apexPsi | 1.3.6.1.4.1.1166.1.31.15 | |||
| apexPsiConfig | 1.3.6.1.4.1.1166.1.31.15.1 | |||
| apexPsiConfigGeneral | 1.3.6.1.4.1.1166.1.31.15.1.1 | |||
| ENA apexPsiDetectionEnabled | 1.3.6.1.4.1.1166.1.31.15.1.1.1 | EnableDisableTYPE | read-write | The loss of input PSI detection enabled or disabled setting. When enabled, the APEX will check for missing input PSI (PATs and PMTs) based on the PSI detection timeout value. When an input PSI message is determined to be missing, the APEX will assume the input service or services are no longer being streamed and unmap the service(s). This checking only occurs after an initial PSI message has been extracted. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexPsiDetectionTimeout | 1.3.6.1.4.1.1166.1.31.15.1.1.2 | Integer32 | read-write | The loss of input PSI detection timeout value. When PSI detection is enabled, this is the number of seconds the APEX will use to determine if an input PSI message is missing. Each PSI message previously extracted will be checked to determine that it is still being received based on this setting. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexPsip | 1.3.6.1.4.1.1166.1.31.25 | |||
| apexPsipConfig | 1.3.6.1.4.1.1166.1.31.25.1 | |||
| APP apexPsipConfigApplyChange | 1.3.6.1.4.1.1166.1.31.25.1.1.1 | ApplyDataToDeviceTYPE | read-write | The Apply for parameters in apexPsipConfigGeneral. This parameter MUST be set to 'apply' in order for other apexPsipConfigGeneral parameters to take effect. This parameter MUST be set LAST after other apexPsipConfigGeneral parameters have been configured. @Config(config=no, reboot=no) |
| U32 apexPsipConfigCvctMsgInsertionPeriod | 1.3.6.1.4.1.1166.1.31.25.1.1.4 | Unsigned32 | read-write | Specify insertion rate (ms) for CVCT PSIP table. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigEit0InsertionPeriod | 1.3.6.1.4.1.1166.1.31.25.1.1.6 | Unsigned32 | read-write | EIT insertion rate (ms) of EIT-0. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigEit1InsertionPeriod | 1.3.6.1.4.1.1166.1.31.25.1.1.7 | Unsigned32 | read-write | EIT insertion rate (ms) of EIT-1. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigEit2InsertionPeriod | 1.3.6.1.4.1.1166.1.31.25.1.1.8 | Unsigned32 | read-write | EIT insertion rate (ms) of EIT-2. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigEit3InsertionPeriod | 1.3.6.1.4.1.1166.1.31.25.1.1.9 | Unsigned32 | read-write | EIT insertion rate (ms) of EIT-3. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexPsipConfigGeneral | 1.3.6.1.4.1.1166.1.31.25.1.1 | |||
| U32 apexPsipConfigMgtMsgInsertionPeriod | 1.3.6.1.4.1.1166.1.31.25.1.1.2 | Unsigned32 | read-write | Specify insertion rate (ms) for MGT PSIP table. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigRrtMsgInsertionPeriod | 1.3.6.1.4.1.1166.1.31.25.1.1.5 | Unsigned32 | read-write | Specify insertion rate (ms) for RRT PSIP table. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigSttMsgInsertionPeriod | 1.3.6.1.4.1.1166.1.31.25.1.1.3 | Unsigned32 | read-write | Specify insertion rate (ms) for STT PSIP table. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexPsipConfigTime | 1.3.6.1.4.1.1166.1.31.25.1.2 | |||
| APP apexPsipConfigTimeApplyChange | 1.3.6.1.4.1.1166.1.31.25.1.2.1 | ApplyDataToDeviceTYPE | read-write | The Apply for parameters in apexPsipConfigTime group. This parameter MUST be set to 'apply' in order for other apexPsipConfigTime parameters to take effect. This parameter MUST be set LAST after other apexPsipConfigTime parameters have been configured. @Config(config=no, reboot=no) |
| U32 apexPsipConfigTimeDsDayIn | 1.3.6.1.4.1.1166.1.31.25.1.2.3 | Unsigned32 | read-write | Configurable day for entering DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigTimeDsDayOut | 1.3.6.1.4.1.1166.1.31.25.1.2.6 | Unsigned32 | read-write | Configurable day for exiting DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigTimeDsHourIn | 1.3.6.1.4.1.1166.1.31.25.1.2.4 | Unsigned32 | read-write | Configurable hour for entering DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigTimeDsHourOut | 1.3.6.1.4.1.1166.1.31.25.1.2.7 | Unsigned32 | read-write | Configurable hour for exiting DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigTimeDsMonthIn | 1.3.6.1.4.1.1166.1.31.25.1.2.2 | Unsigned32 | read-write | Configurable month for entering DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexPsipConfigTimeDsMonthOut | 1.3.6.1.4.1.1166.1.31.25.1.2.5 | Unsigned32 | read-write | Configurable month for exiting DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexPsipStatus | 1.3.6.1.4.1.1166.1.31.25.2 | |||
| apexPsipStatusGeneral | 1.3.6.1.4.1.1166.1.31.25.2.1 | |||
| STR apexPsipStatusInputBody | 1.3.6.1.4.1.1166.1.31.25.2.2.1.7 | DisplayString | read-only | Raw ASCII hex of the PSIP message. |
| apexPsipStatusInputEntry | 1.3.6.1.4.1.1166.1.31.25.2.2.1 | not-accessible | PSIP Table Entry. | |
| I32 apexPsipStatusInputGpsTime | 1.3.6.1.4.1.1166.1.31.25.2.2.1.8 | Integer32 | read-only | The GPS time when the PSIP message was added to the table. |
| I32 apexPsipStatusInputIndex | 1.3.6.1.4.1.1166.1.31.25.2.2.1.1 | Integer32 | not-accessible | Indicates the input index for which this message applies. |
| STR apexPsipStatusInputInfo | 1.3.6.1.4.1.1166.1.31.25.2.2.1.9 | DisplayString | read-only | Comma-separated string showing Input Interface, UDP port, Multicast IP, and Source IP for this PSIP message. |
| I32 apexPsipStatusInputMessageType | 1.3.6.1.4.1.1166.1.31.25.2.2.1.3 | Integer32 | not-accessible | Indicates the PSIP message type. 199 - MGT 200 - TVCT 201 - CVCT 203 - EIT 202 - RRT 205 - STT |
| I32 apexPsipStatusInputPart | 1.3.6.1.4.1.1166.1.31.25.2.2.1.6 | Integer32 | not-accessible | Since a message can be 4096 bytes long the message may divided into parts. Each part of the message is indexed using this index. |
| I32 apexPsipStatusInputPid | 1.3.6.1.4.1.1166.1.31.25.2.2.1.2 | Integer32 | not-accessible | Indicates the PID that this message is contained in. |
| I32 apexPsipStatusInputSegment | 1.3.6.1.4.1.1166.1.31.25.2.2.1.5 | Integer32 | not-accessible | Indicates the segment number of this message. Otherwise this is 0. |
| I32 apexPsipStatusInputSourceId | 1.3.6.1.4.1.1166.1.31.25.2.2.1.4 | Integer32 | not-accessible | Indicates the Source Id of EIT tables. When a message is not specifically related to a program, this value is 0. |
| apexPsipStatusInputTable | 1.3.6.1.4.1.1166.1.31.25.2.2 | not-accessible | The following table contains a list of messages that are being extracted from the input side. | |
| STR apexPsipStatusOutputBody | 1.3.6.1.4.1.1166.1.31.25.2.3.1.7 | DisplayString | read-only | Raw ASCII hex of the PSIP message. |
| apexPsipStatusOutputEntry | 1.3.6.1.4.1.1166.1.31.25.2.3.1 | not-accessible | PSIP Table Entry. | |
| I32 apexPsipStatusOutputGpsTime | 1.3.6.1.4.1.1166.1.31.25.2.3.1.8 | Integer32 | read-only | The GPS time when the PSIP message was added to the table. |
| I32 apexPsipStatusOutputIndex | 1.3.6.1.4.1.1166.1.31.25.2.3.1.1 | Integer32 | not-accessible | Indicates the Output index for which this message applies. This is the Output Transport Stream number (1..48). |
| I32 apexPsipStatusOutputMessageType | 1.3.6.1.4.1.1166.1.31.25.2.3.1.3 | Integer32 | not-accessible | Indicates the PSIP message type. 199 - MGT 200 - TVCT 201 - CVCT 203 - EIT 202 - RRT 205 - STT |
| I32 apexPsipStatusOutputPart | 1.3.6.1.4.1.1166.1.31.25.2.3.1.6 | Integer32 | not-accessible | Since a message can be 4096 bytes long the message may divided into parts. Each part of the message is indexed using this index. |
| I32 apexPsipStatusOutputPid | 1.3.6.1.4.1.1166.1.31.25.2.3.1.2 | Integer32 | not-accessible | Indicates the PID that this message is contained in. |
| I32 apexPsipStatusOutputSegment | 1.3.6.1.4.1.1166.1.31.25.2.3.1.5 | Integer32 | not-accessible | Indicates the segment number of this message. Otherwise this is 0. |
| I32 apexPsipStatusOutputSourceId | 1.3.6.1.4.1.1166.1.31.25.2.3.1.4 | Integer32 | not-accessible | Indicates the Source Id of EIT tables. When a message is not specifically related to a program, this value is 0. |
| apexPsipStatusOutputTable | 1.3.6.1.4.1.1166.1.31.25.2.3 | not-accessible | The following table contains a list of messages that are being inserted to the output side of the apex. | |
| apexPsipStatusServiceEntry | 1.3.6.1.4.1.1166.1.31.25.2.4.1 | not-accessible | PSIP Status Table Entry per service. | |
| I32 apexPsipStatusServiceIndex | 1.3.6.1.4.1.1166.1.31.25.2.4.1.1 | Integer32 | not-accessible | Output Program Table Index. |
| I32 apexPsipStatusServiceNum | 1.3.6.1.4.1.1166.1.31.25.2.4.1.2 | Integer32 | read-only | Current Output Service Number. |
| I32 apexPsipStatusServiceOutputTs | 1.3.6.1.4.1.1166.1.31.25.2.4.1.3 | Integer32 | read-only | Current Output Transport Stream of this service. |
| I32 apexPsipStatusServiceSourceId | 1.3.6.1.4.1.1166.1.31.25.2.4.1.5 | Integer32 | read-only | Current PSIP Program Source Id. |
| STR apexPsipStatusServiceState | 1.3.6.1.4.1.1166.1.31.25.2.4.1.4 | DisplayString | read-only | Current program PSIP state. |
| apexPsipStatusServiceTable | 1.3.6.1.4.1.1166.1.31.25.2.4 | not-accessible | The following table shows the PSIP status per service. For each service, the service number, the Output Transport Stream number, its PSIP state and its source id are shown in the current entry. This table is indexed the same as apexOutputProgramTable. | |
| I32 apexPsiRangeStart | 1.3.6.1.4.1.1166.1.31.15.1.1.3 | Integer32 | read-write | Minimum PSI version number. Used to limit the APEX to use a specific range of PSI numbers. Set this to 0 to allow the APEX to use the full range of PSI version numbers (requires apexPsiRangeStop to be set to 31). Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexPsiRangeStop | 1.3.6.1.4.1.1166.1.31.15.1.1.4 | Integer32 | read-write | Maximum PSI version number. Used to limit the APEX to use a specific range of PSI numbers. Set this to 31 to allow the APEX to use the full range of PSI version numbers (requires apexPsiRangeStart to be set to 0). Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexPsiStatus | 1.3.6.1.4.1.1166.1.31.15.2 | |||
| STR apexPsiStatusBody | 1.3.6.1.4.1.1166.1.31.15.2.2.1.8 | DisplayString | read-only | Raw ASCII hex of the PSI message. |
| apexPsiStatusEntry | 1.3.6.1.4.1.1166.1.31.15.2.2.1 | not-accessible | PSI Table Entry. | |
| apexPsiStatusGeneral | 1.3.6.1.4.1.1166.1.31.15.2.1 | |||
| I32 apexPsiStatusGpsTime | 1.3.6.1.4.1.1166.1.31.15.2.2.1.9 | Integer32 | read-only | The GPS time when the PSI was added to the table. |
| I32 apexPsiStatusIndex | 1.3.6.1.4.1.1166.1.31.15.2.2.1.2 | Integer32 | not-accessible | Indicates the input index or output number for which this message applies. For input, this is the index into the apexInputTsStatTable (1..784). For output, this is the Output Transport Stream number (1..48). |
| I32 apexPsiStatusMessageType | 1.3.6.1.4.1.1166.1.31.15.2.2.1.4 | Integer32 | not-accessible | Indicates the MPEG message type of this message. |
| I32 apexPsiStatusPart | 1.3.6.1.4.1.1166.1.31.15.2.2.1.7 | Integer32 | not-accessible | Since a message can be 1024 bytes long the message may divided into parts. Each part of the message is indexed using this index. |
| I32 apexPsiStatusPid | 1.3.6.1.4.1.1166.1.31.15.2.2.1.3 | Integer32 | not-accessible | Indicates the PID that this message is contained in. |
| I32 apexPsiStatusProgramNumber | 1.3.6.1.4.1.1166.1.31.15.2.2.1.5 | Integer32 | not-accessible | Indicates the Program Number which this message is part of. When a message is not specifically related to a program, this value is 0. |
| I32 apexPsiStatusSegment | 1.3.6.1.4.1.1166.1.31.15.2.2.1.6 | Integer32 | not-accessible | Indicates the segment number of this message. Useful for PAT messages. Otherwise this is 0. |
| apexPsiStatusTable | 1.3.6.1.4.1.1166.1.31.15.2.2 | not-accessible | The following table contains a list of messages that are either being extracted from the input side or being inserted to the output side of the apex. On the input side all extracted messages that are being used by the APEX are displayed. On the output side, only PATs, PMTs, and CATs are displayed. These messages were either given to the apex when it is in external mode or created by the apex when it is in internal mode. | |
| INT apexPsiStatusTableType | 1.3.6.1.4.1.1166.1.31.15.2.2.1.1 | INTEGER | not-accessible | Indicates whether this message is extracted from an input or being inserted on an output. |
| apexPsStatus | 1.3.6.1.4.1.1166.1.31.4.2 | |||
| INT apexPsStatusCommError | 1.3.6.1.4.1.1166.1.31.4.2.2.1.14 | INTEGER | read-only | Communication with the Power Supply has failed and status cannot be determined. Only applies when valid PS installed. |
| I32 apexPsStatusDiagnosticData1 | 1.3.6.1.4.1.1166.1.31.4.2.2.1.12 | Integer32 | read-only | Diagnostic data word 1 (HP) - Contents for Motorola diagnostic purposes. |
| I32 apexPsStatusDiagnosticData2 | 1.3.6.1.4.1.1166.1.31.4.2.2.1.13 | Integer32 | read-only | Diagnostic data word 2 (PS) - Contents for Motorola diagnostic purposes. |
| apexPsStatusEntry | 1.3.6.1.4.1.1166.1.31.4.2.2.1 | not-accessible | Power Supply Status Table Entry. | |
| INT apexPsStatusErrorStatus | 1.3.6.1.4.1.1166.1.31.4.2.2.1.10 | INTEGER | read-only | Summary of errors reported on a power supply basis. The reported error will be the most severe. |
| U32 apexPsStatusFanSpeed | 1.3.6.1.4.1.1166.1.31.4.2.2.1.5 | Unsigned32 | read-only | The fan speed in RPM an installed Power Supply or Fan Module. Zero if not installed. |
| INT apexPsStatusFanStatus | 1.3.6.1.4.1.1166.1.31.4.2.2.1.6 | INTEGER | read-only | PS Fan Status. |
| INT apexPsStatusFaultCondition | 1.3.6.1.4.1.1166.1.31.4.2.2.1.11 | INTEGER | read-only | Current fault condition of the power supply errors. |
| apexPsStatusGeneral | 1.3.6.1.4.1.1166.1.31.4.2.1 | |||
| INT apexPsStatusInputPowerStatus | 1.3.6.1.4.1.1166.1.31.4.2.2.1.8 | INTEGER | read-only | Indicates whether AC Input is within specification. Note that Output Power Status will be 'error' when Input Power status is 'error' |
| INT apexPsStatusInstalled | 1.3.6.1.4.1.1166.1.31.4.2.2.1.2 | INTEGER | read-only | This parameter indicates installed status of the PS. |
| I32 apexPsStatusOutputCurrent | 1.3.6.1.4.1.1166.1.31.4.2.2.1.4 | Integer32 | read-only | PS measured output current in milli-Amps. |
| INT apexPsStatusOutputPowerStatus | 1.3.6.1.4.1.1166.1.31.4.2.2.1.9 | INTEGER | read-only | Indicates whether the +12V and +3.3V output power are within specification. If the output power error occurs with an Input Power error, apply input power to recover. If the output power error occurs with an Over Temperature error, a power cycle is not required for recovery. Otherwise, a power cycle is required for recovery. If the problem persists after the power cycle, the PS must be replaced for recovery. |
| I32 apexPsStatusOutputVoltage | 1.3.6.1.4.1.1166.1.31.4.2.2.1.3 | Integer32 | read-only | PS measured output voltage in milli-Volts. |
| I32 apexPsStatusPsNum | 1.3.6.1.4.1.1166.1.31.4.2.2.1.1 | Integer32 | not-accessible | PS Number. |
| apexPsStatusTable | 1.3.6.1.4.1.1166.1.31.4.2.2 | not-accessible | This is a table of status parameters for the two Power Supplies. | |
| INT apexPsStatusTemperatureStatus | 1.3.6.1.4.1.1166.1.31.4.2.2.1.7 | INTEGER | read-only | Indicates whether the power supply is in protection mode due to an over temperature condition. The PS is shut down while in 'overTemp' and will recover when the temperature returns to normal operating range. A power cycle is not required for recovery. Note that Output Power Status will be 'error' when Temperature status is 'overTemp'. |
| apexPsStatusVersionsEntry | 1.3.6.1.4.1.1166.1.31.4.2.3.1 | not-accessible | Power Supply Version Status Table Entry. | |
| STR apexPsStatusVersionsModel | 1.3.6.1.4.1.1166.1.31.4.2.3.1.2 | DisplayString | read-only | PS Model. |
| I32 apexPsStatusVersionsPsNum | 1.3.6.1.4.1.1166.1.31.4.2.3.1.1 | Integer32 | not-accessible | PS Number. |
| STR apexPsStatusVersionsSerialNumber | 1.3.6.1.4.1.1166.1.31.4.2.3.1.3 | DisplayString | read-only | PS serial number. |
| apexPsStatusVersionsTable | 1.3.6.1.4.1.1166.1.31.4.2.3 | not-accessible | This is a table of version status parameters for the two Power Supplies. | |
| apexQam | 1.3.6.1.4.1.1166.1.31.8 | |||
| I32 apexQamChanConfigChannelNum | 1.3.6.1.4.1.1166.1.31.8.1.5.1.1 | Integer32 | not-accessible | The QAM RF Port number. |
| INT apexQamChanConfigInterleaverSelect | 1.3.6.1.4.1.1166.1.31.8.1.5.1.2 | INTEGER | read-write | The interleaver selection for this Channel. Will use either apexQamRfConfigInterleaverDepth1 or apexQamRfConfigInterleaverDepth2. |
| INT apexQamChanConfigTestMode | 1.3.6.1.4.1.1166.1.31.8.1.5.1.3 | INTEGER | read-write | Test mode setting for the QAM Channel. Setting to other than 'off' will cause a service interruption. |
| APP apexQamChannelConfigApplyChange | 1.3.6.1.4.1.1166.1.31.8.1.7.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for a row of data in apexQamChannelConfigTable. A row in this table corresponds to the same row index in the apexQamChannelConfigTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no) |
| I32 apexQamChannelConfigApplyChannelNum | 1.3.6.1.4.1.1166.1.31.8.1.7.1.1 | Integer32 | not-accessible | The QAM Channel number. |
| apexQamChannelConfigApplyEntry | 1.3.6.1.4.1.1166.1.31.8.1.7.1 | not-accessible | QAM Channel Configuration Apply Table Entry. | |
| apexQamChannelConfigApplyTable | 1.3.6.1.4.1.1166.1.31.8.1.7 | not-accessible | Table of Apply Change for the data for apexQamChannelConfigTable. | |
| apexQamChannelConfigEntry | 1.3.6.1.4.1.1166.1.31.8.1.5.1 | not-accessible | QAM Channel Configuration Table Entry. | |
| apexQamChannelConfigTable | 1.3.6.1.4.1.1166.1.31.8.1.5 | not-accessible | Table of configuration items configurable on a QAM Channel basis. There are 48 Output Transport Streams (OTS) on an APEX1000. There can be up to 48 QAM Channels on an APEX1000 depending on how the 3 QAM slots are populated. There is a one-to-one mapping between QAM Channels and Output Transport Streams. QAM Channel (OTS) ranges are mapped to QAM slots as follows: Slot Channels 1 1..15 2 15..32 3 33..48 There can be either 4 or 8 QAM channels (OTS) on each RF Port. The slot and RF Port to QAM Channel (OTS) mappings for each QAM Module type are shown below. For a 2x4 or 2x8 QAM Module, QAM Channels (OTS) are mapped to RF Ports in a QAM Slot and table rows as follows: QAM Channel RF Port and OTS Slot/Port Table Row Table Rows 1/1 1 1..8 1/2 2 9..16 2/1 5 17..24 2/2 6 25..32 3/1 9 33..40 3/2 10 41..48 If a 2x4 QAM Module is in a slot, only the first four rows in this table for the slot/port are to be used. For example, if there is a 2x4 module in slot 3, rows 8..12 are to be used for configuring the QAM Channels of RF Port 1 on the module. For a 4x4 QAM Module, QAM Channels (OTS) are mapped to RF Ports in a QAM Slot and table rows as follows: QAM Channel RF Port and OTS Slot/Port Table Row Table Rows 1/1 1 1..4 1/2 2 5..8 1/3 7 9..12 1/4 8 13..16 2/1 3 17..20 2/2 4 21..24 2/3 9 25..28 2/4 10 29..32 3/1 5 33..36 3/2 6 37..40 3/3 11 41..44 3/4 12 45..48 Note that the QAM Channels on an RF Port are designated with the letters 'A'..'H' on the APEX Element Manager. Refer to the description of apexQamChannelConfigTable for information on QAM Channel to RF Port mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. Once written, the change to this table will only take immediate effect after apexQamConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamChannelConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| STR apexQamChannelIdChannelDescription | 1.3.6.1.4.1.1166.1.31.8.2.11.1.6 | DisplayString | read-only | Text description for the QAM Channel (Output Transport Stream). Format is as follows where brackets and bracketed descriptions are replaced by a number/letter as appropriate: [QAM Channel / TS Num]:Slot[QAM Slot Num]-[Module Rf Port Num][Channel Letter] Examples: TS 9, in QAM Slot 1, on RF Port 2: '09:Slot1-2A' TS 17, in QAM Slot 2, on RF Port 1: '17:Slot2-1A' TS 48, in QAM Slot 3, on RF Port 2: '48:Slot3-2H' TS 48, in QAM Slot 3, on RF Port 4: '48:Slot3-4D' This may be used for display purposes on a management system. String will be empty or contain '[QAM Channel / TS Num]:Inactive' if apexQamChanStatActive is not set to 'active', i.e. if QAM Channel is not present and/or not enabled. |
| STR apexQamChannelIdChannelLetter | 1.3.6.1.4.1.1166.1.31.8.2.11.1.5 | DisplayString | read-only | The letter symbol ('A'..'H') for the channel. String will be empty if QAM Channel not present. |
| I32 apexQamChannelIdChannelNum | 1.3.6.1.4.1.1166.1.31.8.2.11.1.1 | Integer32 | not-accessible | QAM Channel number (Output Transport number). |
| apexQamChannelIdEntry | 1.3.6.1.4.1.1166.1.31.8.2.11.1 | not-accessible | QAM Channel Identification Table Entry. | |
| I32 apexQamChannelIdModuleRfPortNum | 1.3.6.1.4.1.1166.1.31.8.2.11.1.4 | Integer32 | read-only | Module RF Port number of the channel. Corresponds to RF Port numbering on the back of physical QAM Module. '0' - Indicates QAM Channel is not present. |
| I32 apexQamChannelIdRfPortNum | 1.3.6.1.4.1.1166.1.31.8.2.11.1.3 | Integer32 | read-only | RF Port number of the channel. This may be used to access data in tables indexed by RF Port Number. '0' - Indicates QAM Channel is not present. |
| I32 apexQamChannelIdSlotNum | 1.3.6.1.4.1.1166.1.31.8.2.11.1.2 | Integer32 | read-only | QAM Slot number of the channel. |
| apexQamChannelIdTable | 1.3.6.1.4.1.1166.1.31.8.2.11 | not-accessible | Table of QAM Channel Identification data. Identifies the physical location of the QAM Channel (Output Transport Stream) in the APEX chassis. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. | |
| I32 apexQamChannelsActiveCount | 1.3.6.1.4.1.1166.1.31.8.2.1.4 | Integer32 | read-only | Number of QAM Channels that are present (QAM Module installed) and enabled for use. |
| apexQamChannelStatusEntry | 1.3.6.1.4.1.1166.1.31.8.2.6.1 | not-accessible | QAM Channel Status Table Entry. | |
| apexQamChannelStatusTable | 1.3.6.1.4.1.1166.1.31.8.2.6 | not-accessible | Table of QAM Channel Status. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. | |
| ACT apexQamChanStatActive | 1.3.6.1.4.1.1166.1.31.8.2.6.1.2 | ActiveTYPE | read-only | 'active' indicates that mappings can be made to the channel. This means that either: 1) The channel is present (apexQamModuleStatInstalled 'qam2x4Channel' or 'qam2x8Channel') and enabled for use (apexQamRfConfigNumChannelsEnabled); 2) Or, the channel is on the backup RF port when QAM RF Redundancy is enabled (apexQamRfRedundConfigEnable). |
| I32 apexQamChanStatChannelNum | 1.3.6.1.4.1.1166.1.31.8.2.6.1.1 | Integer32 | not-accessible | QAM Channel number. |
| INT apexQamChanStatDataPresent | 1.3.6.1.4.1.1166.1.31.8.2.6.1.5 | INTEGER | read-only | Indication of MPEG data activity on the interface for this QAM channel. This includes MPEG null packets. |
| I32 apexQamChanStatEiaChanNum | 1.3.6.1.4.1.1166.1.31.8.2.6.1.4 | Integer32 | read-only | The EIA Channel number for the QAM Channel. Will be zero if there is no EIA Channel number corresponding to the frequency in use. |
| INT apexQamChanStatError | 1.3.6.1.4.1.1166.1.31.8.2.6.1.6 | INTEGER | read-only | Summary of errors reported on a QAM channel. This is enumerated and the reported error will be the most severe. |
| INT apexQamChanStatFaultCondition | 1.3.6.1.4.1.1166.1.31.8.2.6.1.7 | INTEGER | read-only | Current fault condition of the QAM channel errors. Reflects apexAlarmQamChannelFault for this QAM Channel. |
| I32 apexQamChanStatRfFreq | 1.3.6.1.4.1.1166.1.31.8.2.6.1.3 | Integer32 | read-only | The center frequency for the QAM Channel in Hz. |
| apexQamConfig | 1.3.6.1.4.1.1166.1.31.8.1 | |||
| APP apexQamConfigApplyChange | 1.3.6.1.4.1.1166.1.31.8.1.3.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for a row of data in apexQamRfConfigTable. A row in this table corresponds to the same row index in the apexQamRfConfigTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no) |
| apexQamConfigApplyEntry | 1.3.6.1.4.1.1166.1.31.8.1.3.1 | not-accessible | QAM Configuration Apply Table Entry. | |
| I32 apexQamConfigApplyRfPortNum | 1.3.6.1.4.1.1166.1.31.8.1.3.1.1 | Integer32 | not-accessible | The QAM RF Port number. Port 1,2,7,8 is Slot 1 Port 3,4,9,10 is Slot 2 Port 5,6,11,12 is Slot 3 |
| apexQamConfigApplyTable | 1.3.6.1.4.1.1166.1.31.8.1.3 | not-accessible | Table of Apply Change for the data for apexQamRfConfigTable. | |
| apexQamConfigGeneral | 1.3.6.1.4.1.1166.1.31.8.1.1 | |||
| INT apexQamConfigTransmissionMode | 1.3.6.1.4.1.1166.1.31.8.1.1.1 | INTEGER | read-write | This is the QAM Transmission Mode as defined in: Series J: Transmission of Television, Sound Programme and other Multimedia Signals, ITU-T J.83. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexQamModuleInstalledCount | 1.3.6.1.4.1.1166.1.31.8.2.1.2 | Integer32 | read-only | Number of hot swappable QAM Modules currently installed. |
| STR apexQamModuleSerialNumber | 1.3.6.1.4.1.1166.1.31.8.2.3.1.2 | DisplayString | read-only | The serial number of an installed QAM Module. Zero if not installed. |
| apexQamModuleSerialNumEntry | 1.3.6.1.4.1.1166.1.31.8.2.3.1 | not-accessible | QAM Module Serial Number Table Entry. | |
| I32 apexQamModuleSerialNumQamModuleNum | 1.3.6.1.4.1.1166.1.31.8.2.3.1.1 | Integer32 | not-accessible | QAM Module slot number. |
| apexQamModuleSerialNumTable | 1.3.6.1.4.1.1166.1.31.8.2.3 | not-accessible | Table of QAM Module Serial Numbers. | |
| INT apexQamModuleStat3dot3VdcFault | 1.3.6.1.4.1.1166.1.31.8.2.2.1.16 | INTEGER | read-only | The +3.3 VDC supply fault of the 4x4 QAM module board. Used only for 4x4 QAM Modules. Indicates there is a problem with the direct 3.3 VDC supply or any internal module supply derived from the 3.3 VDC supply. Indicates voltage problem that can impair module function. |
| I32 apexQamModuleStat3dot3VdcSupply | 1.3.6.1.4.1.1166.1.31.8.2.2.1.15 | Integer32 | read-only | Measured level of the +3.3 VDC supply input of the 4x4 QAM module board. Used only for 4x4 QAM Modules. Range is 0 to 1000 representing 0 to 10 Volts in 0.01 Volt steps. |
| INT apexQamModuleStat5VdcFault | 1.3.6.1.4.1.1166.1.31.8.2.2.1.14 | INTEGER | read-only | The +5 VDC supply fault of the 4x4 QAM module board. Used only for 4x4 QAM Modules. Indicates there is a problem with the direct 5 VDC supply or any internal module supply derived from the 5 VDC supply. Indicates voltage problem that can impair module function. |
| I32 apexQamModuleStat5VdcSupply | 1.3.6.1.4.1.1166.1.31.8.2.2.1.13 | Integer32 | read-only | Measured level of the +5 VDC supply input of the 4x4 QAM module board. Used only for 4x4 QAM Modules. Range is 0 to 1000 representing 0 to 10 Volts in 0.01 Volt steps. |
| I32 apexQamModuleStatBoardTemperature | 1.3.6.1.4.1.1166.1.31.8.2.2.1.11 | Integer32 | read-only | Temperature of the 4x4 QAM module board ('plate' temp) in degrees Celsius. Used only for 4x4 QAM Modules. |
| INT apexQamModuleStatBoardTemperatureFault | 1.3.6.1.4.1.1166.1.31.8.2.2.1.12 | INTEGER | read-only | Board temperature fault of the 4x4 QAM module board ('plate' temp). Used only for 4x4 QAM Modules. This fault is reported in apexAlarmTemperatureFault not apexAlarmQamModuleFault. |
| INT apexQamModuleStatCodeInitError | 1.3.6.1.4.1.1166.1.31.8.2.2.1.18 | INTEGER | read-only | Code initialization error of the 4x4 QAM Module. Used only for 4x4 QAM Modules. Indicates a code, firmware, or FPGA startup issue. The module failed to load the FW/FPGA files to the devices or valid FW/FPGA files could not be found in the module. Code download is required to restore the module. |
| INT apexQamModuleStatCommError | 1.3.6.1.4.1.1166.1.31.8.2.2.1.17 | INTEGER | read-only | Communication with the 4x4 QAM Module has failed. Used only for 4x4 QAM Modules. |
| INT apexQamModuleStatError | 1.3.6.1.4.1.1166.1.31.8.2.2.1.7 | INTEGER | read-only | Summary of errors reported on an QAM Module basis. These errors are reported in apexAlarmQamModuleFault. ok - No errors. removed - Reflects apexQamModuleStatInstalled. unsupported - Reflects apexQamModuleStatInstalled. notInstalled - Reflects apexQamModuleStatInstalled. powerFault - Reflects apexQamModuleStatPowerFault. offline - Indicates the QAM Module and the RF Ports on it are being brought to operational mode after module is inserted or the module has recovered from a power fault. dc5VoltError - 5 Vdc error, see also apexQamModuleStat5VdcSupply and apexQamModuleStat5VdcFault. dc3-3VoltError - 3.3 Vdc error, see also apexQamModuleStat3dot3VdcSupply and apexQamModuleStat3dot3VdcFault. commLost - Communication Lost, see also apexQamModuleStatCommError. codeVersions - Incorrect Code Versions on module, see also apexQamModuleStatCodeInitError, apexQamQrmRevisionTable, and apexQamQrmRevisionStatusTable. codeDownload - Code Download In Progress, see also apexQrmDownloadStatusTable. codeDownloadError - Code Download Error, see also apexQrmDownloadStatusTable. |
| INT apexQamModuleStatFanFault | 1.3.6.1.4.1.1166.1.31.8.2.2.1.4 | INTEGER | read-only | Fan Fault. This fault is reported in apexAlarmFanFault not apexAlarmQamModuleFault. |
| U32 apexQamModuleStatFanSpeed | 1.3.6.1.4.1.1166.1.31.8.2.2.1.3 | Unsigned32 | read-only | The fan speed in RPM for installed QAM or Fan Module. Zero if not installed. |
| INT apexQamModuleStatFaultCondition | 1.3.6.1.4.1.1166.1.31.8.2.2.1.8 | INTEGER | read-only | Current fault condition of the QAM Module errors. Reflects apexAlarmQamModuleFault for this QAM Module. |
| INT apexQamModuleStatFaultSumm | 1.3.6.1.4.1.1166.1.31.8.2.2.1.9 | INTEGER | read-only | Roll-up of QAM RF Port and QAM Channel fault conditions for this QAM Module. |
| INT apexQamModuleStatInstalled | 1.3.6.1.4.1.1166.1.31.8.2.2.1.2 | INTEGER | read-only | Indicates if a module is installed and what type. notApplicable - When APEX does not boot properly. notInstalled - No QAM or Fan Module detected in slot. Reported in apexAlarmQamModuleFault. qam2x4Channel - A 2x4 Channel QAM Module installed. qam2x8Channel - A 2x8 Channel QAM Module installed. fanModule - A Fan Module installed. unsupported - Unknown module installed. Reported in apexAlarmQamModuleFault. removed - A QAM Module removed when there are active QAM channels. Reported in apexAlarmQamModuleFault. qamDiscovery - A QAM Module is present and type is being determined. qam4x4Channel - A 4x4 Channel QAM Module is installed. |
| INT apexQamModuleStatPowerFault | 1.3.6.1.4.1.1166.1.31.8.2.2.1.10 | INTEGER | read-only | Power fault. notApplicable - No module installed. ok - Power good. lowVoltageMainboard - Low voltage detected on Mainboard side of connector. lowVoltageQamModule - Low voltage detected on QAM Module side of connector. overCurrent - Over current detected on QAM Module. This fault is reported in apexAlarmQamModuleFault. |
| I32 apexQamModuleStatQamModuleNum | 1.3.6.1.4.1.1166.1.31.8.2.2.1.1 | Integer32 | not-accessible | QAM Module slot number. |
| I32 apexQamModuleStatTemperature | 1.3.6.1.4.1.1166.1.31.8.2.2.1.5 | Integer32 | read-only | Temperature at sensor near the fan of the QAM Module or Fan Module in degrees Celsius. |
| INT apexQamModuleStatTemperatureFault | 1.3.6.1.4.1.1166.1.31.8.2.2.1.6 | INTEGER | read-only | Temperature fault. This fault is reported in apexAlarmTemperatureFault not apexAlarmQamModuleFault. |
| apexQamModuleStatusEntry | 1.3.6.1.4.1.1166.1.31.8.2.2.1 | not-accessible | QAM Module Status Table Entry. | |
| apexQamModuleStatusTable | 1.3.6.1.4.1.1166.1.31.8.2.2 | not-accessible | Table of QAM Module Status. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. | |
| apexQamModuleUpgrade | 1.3.6.1.4.1.1166.1.31.8.1.2 | |||
| APP apexQamModuleUpgradeApplyChange | 1.3.6.1.4.1.1166.1.31.8.1.2.3 | ApplyDataToDeviceTYPE | read-write | This is the Apply for QAM Module Upgrade Slot and Code. This parameter MUST be set to 'apply' in order for apexQamModuleUpgradeSlot and apexQamModuleUpgradeCode to take effect. This parameter MUST be set LAST after apexQamModuleUpgradeSlot and apexQamModuleUpgradeCode has been configured. The APEX will set this to applyNotInProgressInvalidData if the Upgrade Code is incorrect and the QAM Module is not upgraded. @Config(config=no, reboot=no) |
| STR apexQamModuleUpgradeCode | 1.3.6.1.4.1.1166.1.31.8.1.2.2 | DisplayString | read-write | This is the encrypted upgrade code for the QAM Module that is being upgraded from a 2x4 channel module to a 2x8 channel module. The Upgrade Code is specific to a QAM Module and can only be used for the QAM Module with the serial number for which the Upgrade Code was created. Once written, the change to this parameter will only take immediate effect after the corresponding apexQamModuleUpgradeApplyChange is set to 'apply'. This parameter is cleared by the APEX after the apply is complete. @Config(config=no, reboot=no) @Commit(param=apexQamModuleUpgradeApplyChange, value=2) |
| I32 apexQamModuleUpgradeSlot | 1.3.6.1.4.1.1166.1.31.8.1.2.1 | Integer32 | read-write | This is the QAM slot number of the QAM Module that is being upgraded from a 2x4 channel module to a 2x8 channel module. Zero indicates no slot selected. Once written, the change to this table will only take immediate effect after apexQamModuleUpgradeApplyChange is set to 'apply'. @Config(config=no, reboot=no) @Commit(param=apexQamModuleUpgradeApplyChange, value=2) |
| STR apexQamQrmRevAppFw | 1.3.6.1.4.1.1166.1.31.8.2.4.1.3 | DisplayString | read-only | Application firmware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Hex XXYY where XX is major version and YY is minor version. 'FFFF' indicates no valid application code is present. |
| STR apexQamQrmRevBoardId | 1.3.6.1.4.1.1166.1.31.8.2.4.1.2 | DisplayString | read-only | Model ID of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Hex XXYY. |
| STR apexQamQrmRevBootLoaderFw | 1.3.6.1.4.1.1166.1.31.8.2.4.1.4 | DisplayString | read-only | Boot loader firmware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Hex XXYY where XX is major version and YY is minor version. |
| STR apexQamQrmRevFpga | 1.3.6.1.4.1.1166.1.31.8.2.4.1.5 | DisplayString | read-only | FPGA version of the 2x4/2x8 QAM Module's QRM board or FPGA1 version of the 4x4 QAM Module. Hex XXYY where XX is major version and YY is minor version. |
| STR apexQamQrmRevFpga2 | 1.3.6.1.4.1.1166.1.31.8.2.4.1.8 | DisplayString | read-only | FPGA2 version of the 4x4 QAM Module. Used only for 4x4 QAM Modules. Hex XXYY where XX is major version and YY is minor version. |
| STR apexQamQrmRevHw | 1.3.6.1.4.1.1166.1.31.8.2.4.1.6 | DisplayString | read-only | Hardware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Hex XXYY where XX is major version and YY is minor version. |
| apexQamQrmRevisionEntry | 1.3.6.1.4.1.1166.1.31.8.2.4.1 | not-accessible | QAM Module Revision Table Entry. | |
| apexQamQrmRevisionStatusEntry | 1.3.6.1.4.1.1166.1.31.8.2.9.1 | not-accessible | QRM Revision Status Table Entry | |
| apexQamQrmRevisionStatusTable | 1.3.6.1.4.1.1166.1.31.8.2.9 | not-accessible | Table of status of QRM hardware and software revisions. Indications of whether they are supported, current, etc.. There are 2 QRM modules on each 2x4/2x8 QAM Module. QRMs in QAM Module slots are mapped to table rows as follows: Slot/QRM Table Row 1/1 1 1/2 2 2/1 3 2/2 4 3/1 5 3/2 6 4x4 QAM Modules do not use QRM boards. There is only one board. These will be found in the odd indexed rows of this table. The even indexed rows of the table are not used for 4x4 QAM Modules. 4x4 QAM Modules in QAM Module slots are mapped to table rows as follows: Slot Table Row 1 1 2 3 3 5 | |
| apexQamQrmRevisionTable | 1.3.6.1.4.1.1166.1.31.8.2.4 | not-accessible | Table of QAM Module hardware and software revisions. There are 2 QRM modules on each 2x4/2x8 QAM Module. QRMs in QAM Module slots are mapped to table rows as follows: Slot/QRM Table Row 1/1 1 1/2 2 2/1 3 2/2 4 3/1 5 3/2 6 4x4 QAM Modules do not use QRM boards. There is only one board. These will be found in the odd indexed rows of this table. The even indexed rows of the table are not used for 4x4 QAM Modules. 4x4 QAM Modules in QAM Module slots are mapped to table rows as follows: Slot Table Row 1 1 2 3 3 5 | |
| I32 apexQamQrmRevRfPortNum | 1.3.6.1.4.1.1166.1.31.8.2.4.1.1 | Integer32 | not-accessible | QAM Module Revision Table index. |
| STR apexQamQrmRevSerialNumber | 1.3.6.1.4.1.1166.1.31.8.2.4.1.7 | DisplayString | read-only | The serial number of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Zero if not installed. |
| INT apexQamQrmRevStatAppFw | 1.3.6.1.4.1.1166.1.31.8.2.9.1.3 | INTEGER | read-only | Status of Application firmware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQrmFileRevisionTable for the revisions of files in the APEX release resident on the device. |
| INT apexQamQrmRevStatBoardId | 1.3.6.1.4.1.1166.1.31.8.2.9.1.2 | INTEGER | read-only | Status of the Model ID of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQamQrmRevisionTable for the revisions of each QRM. |
| INT apexQamQrmRevStatBootLoaderFw | 1.3.6.1.4.1.1166.1.31.8.2.9.1.4 | INTEGER | read-only | Status of Boot loader firmware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. |
| INT apexQamQrmRevStatFpga | 1.3.6.1.4.1.1166.1.31.8.2.9.1.5 | INTEGER | read-only | Status of FPGA version of the 2x4/2x8 QAM Module's QRM board or FPGA1 version of the 4x4 QAM Module. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQrmFileRevisionTable for the revisions of files in the APEX release resident on the device. |
| INT apexQamQrmRevStatFpga2 | 1.3.6.1.4.1.1166.1.31.8.2.9.1.8 | INTEGER | read-only | Status of FPGA2 version of the 4x4 QAM Module. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module. Refer to apexQrmFileRevisionTable for the revisions of files in the APEX release resident on the device. |
| INT apexQamQrmRevStatHw | 1.3.6.1.4.1.1166.1.31.8.2.9.1.6 | INTEGER | read-only | Status of Hardware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. |
| I32 apexQamQrmRevStatQrmNum | 1.3.6.1.4.1.1166.1.31.8.2.9.1.1 | Integer32 | not-accessible | QRM Revision Status Table index. |
| INT apexQamQrmRevStatQrmSupported | 1.3.6.1.4.1.1166.1.31.8.2.9.1.7 | INTEGER | read-only | Indicates if the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board is supported. Summary of above status. If any 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board revision status is 'notSupported' this parameter will indicate 'notSupported' and apexQamRfPortStatError will report 'unsupportedQrm'. |
| I32 apexQamRfConfigEiaChanNumChannelA | 1.3.6.1.4.1.1166.1.31.8.1.4.1.8 | Integer32 | read-write | The Channel Number for QAM Channel A. Range is 0 to 158, with valid channels being 1 to 158 and 0 indicating 'not applicable'. This parameter is valid only when QAM Transmission Mode is 'annexB-ATSC-DCII'. This parameter is configurable only when Tuning Mode is 'channel'. When Tuning Mode is 'channel', this is the Channel Number used to determine the output frequency of QAM Channel A using the selected Frequency Plan. When Tuning Mode is 'frequency', this value is determined by the APEX using the selected Frequency Plan. If there is no channel number for the frequency, the value is set to zero. This parameter is not configurable for Transmission Modes of 'annexA-DVB' or 'annexC-Asia-Pacific' and the value is set to zero by the APEX. Channel 1 is not defined in CEA Standard: Cable Television Channel Identification Plan (CEA-542-B) for the Standard (STD) North American frequency plan. Channel 1 cannot be selected when apexQamRfConfigEiaFrequencyPlan is 'std'. Channel 2 as defined in defined in CEA Standard: Cable Television Channel Identification Plan (CEA-542-B) for the Harmonic Related Carrier (HRC) frequency plan is below the APEX 57 MHz minimum frequency. Channel 2 cannot be selected when apexQamRfConfigEiaFrequencyPlan is 'hrc'. For 4x4 QAM Modules: Channels with frequencies below 69 MHz may not be available. This limitation is dependent upon the HW version installed and number of channels enabled. |
| INT apexQamRfConfigEiaFrequencyPlan | 1.3.6.1.4.1.1166.1.31.8.1.4.1.7 | INTEGER | read-write | This is the frequency plan to use for tuning of the QAM Channels enabled on the RF Port. Frequency plans are as per CEA Standard: Cable Television Channel Identification Plan (CEA-542-B). This parameter is valid only when QAM Transmission Mode is 'annexB-ATSC-DCII'. 'std' - Standard (STD) North American frequency plan. 'hrc' - Harmonic Related Carrier (HRC) frequency plan. 'irc' - Incremental Related Carrier (IRC) frequency plan. |
| apexQamRfConfigEntry | 1.3.6.1.4.1.1166.1.31.8.1.4.1 | not-accessible | QAM RF Port Configuration Table Entry. | |
| INT apexQamRfConfigInterleaverDepth1 | 1.3.6.1.4.1.1166.1.31.8.1.4.1.15 | INTEGER | read-write | The first of two Interleaver settings that can be assigned to the QAM Channels of this RF Port. Configurable only for Transmission Mode 'annexB-ATSC-DCII'. Values 1 to 12 used only for Transmission Mode 'annexB-ATSC-DCII'. Value 13 (i12-j17) used only for Transmission Modes 'annexA-DVB' and 'annexC-Asia-Pacific' and is set by the APEX. |
| INT apexQamRfConfigInterleaverDepth2 | 1.3.6.1.4.1.1166.1.31.8.1.4.1.16 | INTEGER | read-write | The second of two Interleaver settings that can be assigned to the QAM Channels of this RF Port. Configurable only for Transmission Mode 'annexB-ATSC-DCII'. Values 1 to 12 used only for Transmission Mode 'annexB-ATSC-DCII'. Value 13 (i12-j17) used only for Transmission Modes 'annexA-DVB' and 'annexC-Asia-Pacific' and is set by the APEX. |
| INT apexQamRfConfigModulationMode | 1.3.6.1.4.1.1166.1.31.8.1.4.1.3 | INTEGER | read-write | The QAM Modulation mode for the QAM RF Port. This is the QAM Modulation mode of all QAM Channels enabled on the RF Port. For 4x4 QAM Modules: This parameter applies on an RF pair basis, 1-2 and 7-8. APEX1000 will use only odd table indices. Even index of pair will be ignored and set to value for odd index of pair. |
| INT apexQamRfConfigMute | 1.3.6.1.4.1.1166.1.31.8.1.4.1.14 | INTEGER | read-write | Mute the RF Port. This will mute all QAM channels enabled on the RF Port. |
| I32 apexQamRfConfigNumChannelsEnabled | 1.3.6.1.4.1.1166.1.31.8.1.4.1.2 | Integer32 | read-write | The number of QAM Channels enabled on the RF Port. APEX will not allow enabling of more channels than the installed QAM Module will support. Note that when this parameter is changed and applied there will be an interruption in service on all active channels on this RF Port. When QAM Transmission Mode is 'annexA-DVB', enabled channels is also limited by the Channel Spacing such that the total bandwidth of the RF must not exceed 48 MHz. |
| I32 apexQamRfConfigRfCenterFreqChannelA | 1.3.6.1.4.1.1166.1.31.8.1.4.1.9 | Integer32 | read-write | The RF Center Frequency for QAM Channel A. When QAM Transmission Mode is 'annexA-DVB' the range is 85,000,000 Hz to 999,000,000 Hz in 250,000 Hz steps. For 2x4/2x8 QAM Modules: When QAM Transmission Mode is 'annexB-ATSC-DCII' or 'annexC-Asia-Pacific' the range is 57,000,000 Hz to 999,000,000 Hz in 250,000 Hz steps. For 4x4 QAM Modules: When QAM Transmission Mode is 'annexB-ATSC-DCII' or 'annexC-Asia-Pacific' the range may be limited to 69,000,000 Hz to 999,000,000 Hz in 250,000 Hz steps. This limitation is dependent upon the HW version installed and number of channels enabled. The APEX will correct values not on a 250 kHz boundary so the user or management system does not need to enforce the step size. This parameter is configurable ONLY when Tuning Mode is 'frequency'. When Tuning Mode is 'channel', the value is set by the APEX using the selected Frequency Plan. @Range(step=250000) |
| I32 apexQamRfConfigRfChanSpacing | 1.3.6.1.4.1.1166.1.31.8.1.4.1.10 | Integer32 | read-write | The Channel spacing for the QAM Channels enabled on the RF Port. This value must be in Hz in the range 1,000,000 Hz to 8,000,000 Hz in 500,000 Hz steps. The APEX will correct values not on a 500,000 Hz boundary so the user or management system does not need to enforce the step size. For 2x4/2x8 QAM Modules: When Transmission Mode is 'annexA-DVB' this value is configurable. Note that number of channels enabled can be affected by changing channel spacing. The total bandwidth of the RF must not exceed 48 MHz. For 2x4/2x8 QAM Modules: When Transmission Mode is 'annexB-ATSC-DCII' or 'annexC-Asia-Pacific' this value is fixed and is set by the APEX. For 4x4 QAM Modules: This value is fixed and is set by the APEX. @Range(step=500000) |
| I32 apexQamRfConfigRfLevelAttenuation | 1.3.6.1.4.1.1166.1.31.8.1.4.1.11 | Integer32 | read-write | The RF level attenuation setting of each enabled channel on the RF Port. Range is -300 to 800 representing -3 to 8 dB attenuation in 0.01 dB steps. (See 'Note' below.) Positive values are the amount below the nominal RF output level for the number of channels enabled on the RF Port. Negative values are the amount above the nominal. Number Nominal dBmV dBmV Channels dBmV W/-300 W/800 1 60 63 52 2 56 59 48 4 52 55 44 6 50 53 42 8 49 52 41 Note: Early APEX only supported attenuation. Gain was added later, hence the negative attenuation values for this parameter. For clarity, the APEX Element Manager display indicates 'RF Level Adjust', with a user selectable range of -8.00 to +3.00 dB, rather than 'Attenuation'. The APEX EM then sets this MIB parameter appropriately. |
| I32 apexQamRfConfigRfLevelHighThreshold | 1.3.6.1.4.1.1166.1.31.8.1.4.1.13 | Integer32 | read-write | The threshold delta relative to the configured RF level that will indicate an RF High condition. The measured output must rise this amount for RF High condition. Range is 0 to 100 representing 0 to 10 dB in 0.1 dB steps. |
| I32 apexQamRfConfigRfLevelLowThreshold | 1.3.6.1.4.1.1166.1.31.8.1.4.1.12 | Integer32 | read-write | The threshold delta relative to the configured RF level that will indicate an RF Low condition. The measured output must drop this amount for RF Low condition. Range is 0 to 100 representing 0 to 10 dB in 0.1 dB steps. |
| I32 apexQamRfConfigRfPortNum | 1.3.6.1.4.1.1166.1.31.8.1.4.1.1 | Integer32 | not-accessible | The QAM RF Port number. |
| INT apexQamRfConfigSpectrumInvert | 1.3.6.1.4.1.1166.1.31.8.1.4.1.5 | INTEGER | read-write | The Spectrum Inversion Setting of the QAM Channels enabled on the RF Port. |
| I32 apexQamRfConfigSymbolRate | 1.3.6.1.4.1.1166.1.31.8.1.4.1.4 | Integer32 | read-write | The Symbol Rate Setting of the QAM Channels enabled on the RF Port. It is in symbols per second (sps). When QAM Transmission Mode is 'annexA-DVB' the range is 800,000 sps to 6,980,000 sps in 1000 sps steps. When QAM Transmission Mode is 'annexC-Asia-Pacific' the range is 800,000 sps to 5,310,000 sps in 1000 sps steps. The APEX will correct values not on a 1000 sps boundary so the user or management system does not need to enforce the step size. When QAM Transmission Mode is 'annexB-ATSC-DCII' this parameter is not configurable and is set by the APEX based on QAM Modulation Mode. For 4x4 QAM Modules: This parameter applies on an RF pair basis, 1-2 and 7-8. APEX1000 will use only odd table indices. Even index of pair will be ignored and set to value for odd index of pair. @Range(step=1000) |
| apexQamRfConfigTable | 1.3.6.1.4.1.1166.1.31.8.1.4 | not-accessible | Table of configuration items configurable on a QAM RF Port basis. There can be up to 12 RF Ports on an APEX1000 depending on how the 3 QAM slots are populated. There can be 2 or 4 RF Ports in each QAM slot. The 2 RF Ports in a 2x8(2x4) QAM module (1,2) in a QAM slot are mapped to table rows as follows: Slot Rows (RF port) 1 1,2 2 3,4 3 5,6 If a QAM Module in a slot only has 2 RF ports, the first three rows in this table for that slot are to be used. For example, if there is a 2x4 or 2x8 module in slot 3, port 5 and 6 are to be used for configuring the RF Ports of the module. The 4 RF Ports in a 4x4 QAM module (1,2,7,8) in a QAM slot are mapped to table rows as follows: Slot Rows (RF port) 1 1,2,7,8 2 3,4,9,10 3 5,6,11,12 All entries/rows in this table are used for the 4x4 QAM Module with any exceptions noted in the descriptions for the table entries. All entries in this table have the same ranges for the 4x4 QAM Module with any exceptions noted in the descriptions for the table entries. Refer to the description of apexQamChannelConfigTable for information on QAM Channel to RF Port mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. Once written, the change to this table will only take immediate effect after apexQamConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') | |
| INT apexQamRfConfigTuningMode | 1.3.6.1.4.1.1166.1.31.8.1.4.1.6 | INTEGER | read-write | The tuning mode of the QAM Channels enabled on the RF Port. 'frequency' - The APEX tunes based on frequency as configured in RF Center Frequency for QAM Channel A and channel spacing as configured in RF Channel Spacing to determine the frequency of the B - H channels. 'channel' - The APEX tunes based on channel as configured in Channel Number for QAM Channel A using the selected Frequency Plan. The APEX will set the B - H channels to the next sequential channels. Applies only when QAM Transmission Mode is 'annexB-ATSC-DCII'. |
| I32 apexQamRfPortChannelInfoChanA | 1.3.6.1.4.1.1166.1.31.8.2.10.1.2 | Integer32 | read-only | QAM Channel number (Output Transport number) of QAM Channel 'A' on this RF port. This may be used to access data in tables indexed by QAM Number or Output Transport Stream. Used in combination with apexQamRfPortChannelInfoChanCount, data for all QAM Channels on this RF Port may be accessed. '0' - Indicates RF Port is not present. |
| I32 apexQamRfPortChannelInfoChanCount | 1.3.6.1.4.1.1166.1.31.8.2.10.1.3 | Integer32 | read-only | The number of QAM Channels on the RF port. '0' - Indicates RF Port is not present. '4' - RF Port has 4 QAM Channels, 'A'-'D'. '8' - RF Port has 8 QAM Channels, 'A'-'H'. |
| apexQamRfPortChannelInfoEntry | 1.3.6.1.4.1.1166.1.31.8.2.10.1 | not-accessible | QAM RF Port Channel Information Table Entry. | |
| I32 apexQamRfPortChannelInfoRfPortNum | 1.3.6.1.4.1.1166.1.31.8.2.10.1.1 | Integer32 | not-accessible | RF Port number. |
| apexQamRfPortChannelInfoTable | 1.3.6.1.4.1.1166.1.31.8.2.10 | not-accessible | Table of QAM Channel information for each QAM RF Port. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. | |
| INT apexQamRfPortMuteStatus | 1.3.6.1.4.1.1166.1.31.8.2.8.1.2 | INTEGER | read-only | Indicates whether the QAM channels on the RF port are muted or unmuted. |
| apexQamRfPortMuteStatusEntry | 1.3.6.1.4.1.1166.1.31.8.2.8.1 | not-accessible | QAM RF Port Mute Status Table Entry. | |
| I32 apexQamRfPortMuteStatusRfPortNum | 1.3.6.1.4.1.1166.1.31.8.2.8.1.1 | Integer32 | not-accessible | RF Port number. |
| apexQamRfPortMuteStatusTable | 1.3.6.1.4.1.1166.1.31.8.2.8 | not-accessible | Table of QAM RF Port Mute Status. | |
| INT apexQamRfPortStat3dot3VdcFault | 1.3.6.1.4.1.1166.1.31.8.2.5.1.11 | INTEGER | read-only | The +3.3 VDC supply fault of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Indicates voltage problem that can impair QRM function. |
| I32 apexQamRfPortStat3dot3VdcSupply | 1.3.6.1.4.1.1166.1.31.8.2.5.1.10 | Integer32 | read-only | Measured level of the +3.3 VDC supply input of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Range is 0 to 1000 representing 0 to 10 Volts in 0.01 Volt steps. |
| INT apexQamRfPortStat5VdcFault | 1.3.6.1.4.1.1166.1.31.8.2.5.1.9 | INTEGER | read-only | The +5 VDC supply fault of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Indicates voltage problem that can impair QRM function. |
| I32 apexQamRfPortStat5VdcSupply | 1.3.6.1.4.1.1166.1.31.8.2.5.1.8 | Integer32 | read-only | Measured level of the +5 VDC supply input of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Range is 0 to 1000 representing 0 to 10 Volts in 0.01 Volt steps. |
| INT apexQamRfPortStatChanFaultSumm | 1.3.6.1.4.1.1166.1.31.8.2.5.1.20 | INTEGER | read-only | Roll-up of Channel fault conditions for this RF Port. |
| INT apexQamRfPortStatCodeInitError | 1.3.6.1.4.1.1166.1.31.8.2.5.1.21 | INTEGER | read-only | Code initialization error of the 2x4/2x8 QAM Module's QRM board. Indicates a code, firmware, or FPGA startup issue. 'fpgaInitError' - FPGA not loaded. Caused by incompatible code images or corrupted FPGA image on the QRM. 'calDataError' - Working copy of calibration data was corrupted and needs to be restored by code download process. Caused by interruption of previous code download process. |
| INT apexQamRfPortStatCommError | 1.3.6.1.4.1.1166.1.31.8.2.5.1.17 | INTEGER | read-only | Communication with the 2x4/2x8 QAM Module's QRM board has failed. |
| INT apexQamRfPortStatDataClockPresent | 1.3.6.1.4.1.1166.1.31.8.2.5.1.15 | INTEGER | read-only | Data clock present indication. |
| INT apexQamRfPortStatDataSyncFault | 1.3.6.1.4.1.1166.1.31.8.2.5.1.16 | INTEGER | read-only | One or more of the QAM Channel data interfaces is not synchronized. |
| INT apexQamRfPortStatError | 1.3.6.1.4.1.1166.1.31.8.2.5.1.18 | INTEGER | read-only | Error status on an RF Port basis. These errors are reported in apexAlarmQamRfPortFault. 'major' for: 'outputRfLevel', 'dc5VoltError', 'dc3-3VoltError'. 'critical' for: 'freqPllNotLocked', 'extClkNotPresent', 'extClkNotLocked', 'dataClkNotPresent', 'dataSyncLost', 'commLost', 'codeVersions', 'codeDownload', 'codeDownloadError', 'unsupportedQrm', or 'configFailed'. outputRfLevel - RF Output Level error, see also apexQamRfPortStatOutputLevel and apexQamRfPortStatOutputLevelFault. dc5VoltError - 5 Vdc error, see also apexQamRfPortStat5VdcSupply and apexQamRfPortStat5VdcFault. dc3-3VoltError - 3.3 Vdc error, see also apexQamRfPortStat3dot3VdcSupply and apexQamRfPortStat3dot3VdcFault. freqPllNotLocked - Frequency PLL not locked, see also apexQamRfPortStatFreqPllLock. extClkNotPresent - External Reference Clock Not Present, see also apexQamRfPortStatRefClockPresent. extClkNotLocked - Not Locked to External Reference Clock, see also apexQamRfPortStatRefClockLock. dataClkNotPresent - Data Clock Not Present, see also apexQamRfPortStatDataClockPresent. dataSyncLost - Data Synchronization Lost, see also apexQamRfPortStatDataSyncFault. commLost - Communication Lost, see also apexQamRfPortStatCommError. unsupportedQrm - QRM Revision Not Supported, see also apexQamQrmRevisionTable and apexQamQrmRevisionStatusTable. configFailed - RF Port Configuration Failed. codeVersions - Incorrect Code Versions on QRM, see also apexQamRfPortStatCodeInitError, apexQamQrmRevisionTable, and apexQamQrmRevisionStatusTable. codeDownload - Code Download In Progress, see also apexQrmDownloadStatusTable. codeDownloadError - Code Download Error, see also apexQrmDownloadStatusTable. |
| INT apexQamRfPortStatFaultCondition | 1.3.6.1.4.1.1166.1.31.8.2.5.1.19 | INTEGER | read-only | Current fault condition of the RF Port errors. Reflects apexAlarmQamRfPortFault for this RF Port. |
| INT apexQamRfPortStatFreqPllLock | 1.3.6.1.4.1.1166.1.31.8.2.5.1.12 | INTEGER | read-only | Frequency tuning PLL lock status. |
| U32 apexQamRfPortStatInfoRate | 1.3.6.1.4.1.1166.1.31.8.2.5.1.2 | Unsigned32 | read-only | The information rate of the QAM channels on this RF Port in bits per second. |
| I32 apexQamRfPortStatNumChannelsActive | 1.3.6.1.4.1.1166.1.31.8.2.5.1.3 | Integer32 | read-only | Number of QAM Channels that are present (QAM Module installed) and enabled for use on this RF Port. |
| I32 apexQamRfPortStatOutputLevel | 1.3.6.1.4.1.1166.1.31.8.2.5.1.4 | Integer32 | read-only | Measured per channel RF Output Level. Range is 0 to 8000 representing 0 to 80 dBmV in 0.01 dBmV steps. |
| INT apexQamRfPortStatOutputLevelFault | 1.3.6.1.4.1.1166.1.31.8.2.5.1.5 | INTEGER | read-only | RF Output Level fault. Indicates if the user configured apexQamRfConfigRfLevelLowThreshold or apexQamRfConfigRfLevelHighThreshold has been reached. |
| INT apexQamRfPortStatRefClockLock | 1.3.6.1.4.1.1166.1.31.8.2.5.1.14 | INTEGER | read-only | Board not phase-locked to the External reference clock. |
| INT apexQamRfPortStatRefClockPresent | 1.3.6.1.4.1.1166.1.31.8.2.5.1.13 | INTEGER | read-only | External reference clock present indication. |
| I32 apexQamRfPortStatRfPortNum | 1.3.6.1.4.1.1166.1.31.8.2.5.1.1 | Integer32 | not-accessible | RF Port number. |
| I32 apexQamRfPortStatTemperature | 1.3.6.1.4.1.1166.1.31.8.2.5.1.6 | Integer32 | read-only | Temperature of the 2x4/2x8 QAM Module's QRM board ('plate' temp) in degrees Celsius. Used only for 2x4/2x8 QAM Modules. |
| INT apexQamRfPortStatTemperatureFault | 1.3.6.1.4.1.1166.1.31.8.2.5.1.7 | INTEGER | read-only | Temperature fault of the 2x4/2x8 QAM Module's QRM board ('plate' temp). Used only for 2x4/2x8 QAM Modules. This fault is reported in apexAlarmTemperatureFault not apexAlarmQamRfPortFault. |
| apexQamRfPortStatusEntry | 1.3.6.1.4.1.1166.1.31.8.2.5.1 | not-accessible | QAM RF Port Status Table Entry. | |
| apexQamRfPortStatusTable | 1.3.6.1.4.1.1166.1.31.8.2.5 | not-accessible | Table of QAM RF Port Status. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. | |
| apexQamRfRedundancyConfig | 1.3.6.1.4.1.1166.1.31.8.1.6 | |||
| apexQamRfRedundancyConfigGeneral | 1.3.6.1.4.1.1166.1.31.8.1.6.1 | |||
| apexQamRfRedundancyStatus | 1.3.6.1.4.1.1166.1.31.8.2.7 | |||
| apexQamRfRedundancyStatusGeneral | 1.3.6.1.4.1.1166.1.31.8.2.7.1 | |||
| I32 apexQamRfRedundConfigApexId | 1.3.6.1.4.1.1166.1.31.8.1.6.1.4 | Integer32 | read-write | Identifies which set of RF inputs on the REM1000 are associated with this APEX. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| APP apexQamRfRedundConfigApplyChange | 1.3.6.1.4.1.1166.1.31.8.1.6.1.1 | ApplyDataToDeviceTYPE | read-write | The Apply for QAM RF Redundancy Configuration parameters. This parameter MUST be set to 'apply' in order for the data to take effect. This parameter MUST be set LAST after all QAM RF Redundancy parameters affected by this parameter have been configured. @Config(config=no, reboot=no) |
| ENA apexQamRfRedundConfigAutoSwitchBack | 1.3.6.1.4.1.1166.1.31.8.1.6.1.6 | EnableDisableTYPE | read-write | This is the enable/disable of automatic switch back to the previous RF port from backup for QAM RF redundancy. When 'enabled', switch back to the previous RF port will automatically occur when the RF port comes back online. When 'disabled', the user must force back to the previous RF port using apexQamRfRedundConfigForceSwitch. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexQamRfRedundConfigEnable | 1.3.6.1.4.1.1166.1.31.8.1.6.1.2 | EnableDisableTYPE | read-write | Enables RF redundancy mode, allowing the APEX to failover to backup RF port and communicate with the REM1000. Allows for failover/ switching without requiring a REM1000 connection. Cannot be 'enabled' if the backup port (RF Port 6) is not present (there is no QAM Module in QAM slot 3). Cannot be 'enabled' if there are any mappings to any QAM Channel on the backup port. RF Port 6, QAM Channels 6A to 6H (Output Transport Streams 41 to 48). Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexQamRfRedundConfigForceSwitch | 1.3.6.1.4.1.1166.1.31.8.1.6.1.8 | INTEGER | read-write | Force a switch of an RF Port to or from the backup. Selects which RF Port to switch from. Overrides Suspend Failover (apexQamRfRedundConfigSuspendFailover). Parameter is ignored when: - apexQamRfRedundConfigEnable is 'disabled'. - backup is active and other than 'forceFromBackup' is selected. - backup is not active and 'forceFromBackup' is selected. 'forceFromBackup' will force back to the failed primary indicated in apexQamRfRedundStatusFailedPort. APEX sets back to 'switchNotInProgress' when complete. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| IP apexQamRfRedundConfigRemCommonIpAddr | 1.3.6.1.4.1.1166.1.31.8.1.6.1.5 | IpAddress | read-write | Target REM1000 IP address. Must be singlecast address. Only used when apexQamRfRedundConfigRemConnection is set to 'common'. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexQamRfRedundConfigRemConnection | 1.3.6.1.4.1.1166.1.31.8.1.6.1.3 | INTEGER | read-write | Configures how the APEX is connected to the REM1000. 'none' - Not connecting to REM1000. 'direct' - Connected to REM1000 dedicated IP interface through APEX Data IP (Enet2). Broadcast connection is always used in this case. Cannot be set to 'direct' if the QAM RF Redundancy UDP Port is in use on the Data IP Port (Enet2). QAM RF Redundancy UDP Port value is found in apexQamRfRedundStatusUdpPort. 'common' - Connected to REM1000 OAM&P interface through APEX OAM&P IP (Enet 1). Requires user to configure REM1000 IP address in apexQamRfRedundConfigRemCommonIpAddr. Cannot be set to 'common' if the QAM RF Redundancy UDP Port is in use on the OAM&P IP (Enet 1). QAM RF Redundancy UDP Port value is found in apexQamRfRedundStatusUdpPort. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexQamRfRedundConfigRemDirectIpOctet1 | 1.3.6.1.4.1.1166.1.31.8.1.6.1.9 | Integer32 | read-write | Target REM1000 IP address first octet. Only used when apexQamRfRedundConfigRemConnection is set to 'direct'. The remainder of the IP address will be filled in by the APEX. The IP address used will be reflected in apexDataIpAddrInUse. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexQamRfRedundConfigSuspendFailover | 1.3.6.1.4.1.1166.1.31.8.1.6.1.7 | EnableDisableTYPE | read-write | Enables and disables suspending of RF failover. Prevents failovers to or from backup. Force failover (apexQamRfRedundConfigForceSwitch) overrides this setting. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexQamRfRedundStatusBackupPort | 1.3.6.1.4.1.1166.1.31.8.2.7.1.1 | INTEGER | read-only | State of configured backup port. 'disabled' - QAM RF Redundancy is disabled. 'standby' - QAM RF Redundancy is enabled but backup is inactive. No failure has occurred. 'active' - Failover has occurred and backup is active. Refer to apexQamRfRedundStatusFailedPort for port being backed up. 'failed' - Backup port has failed. APEX cannot provide RF redundancy. 'removed' - QAM Module with Backup port has been removed. APEX cannot provide RF redundancy. |
| I32 apexQamRfRedundStatusFailedPort | 1.3.6.1.4.1.1166.1.31.8.2.7.1.2 | Integer32 | read-only | Indicates which port (1 to 5) has failed over to the backup port. Zero indicates backup port is not active. |
| STR apexQamRfRedundStatusInvalidApplyText | 1.3.6.1.4.1.1166.1.31.8.2.7.1.8 | DisplayString | read-only | When apexQamRfRedundConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid. |
| INT apexQamRfRedundStatusMismatch | 1.3.6.1.4.1.1166.1.31.8.2.7.1.3 | INTEGER | read-only | Indicates whether there is a potential for channels being lost when failing to the backup or when switching back to a primary due to a mixture of 2x4 and 2x8 QAM Modules. Indicates whether RF redundancy is unavailable due to a 4x4 QAM Module installed. A 2x4 QAM Module is capable of supporting a maximum of 4 channels per RF port. A 2x8 QAM Module is capable of supporting a maximum of 8 channels per RF port. The number of channels enabled (apexQamRfConfigNumChannelsEnabled) is not considered. 'notApplicable' - QAM RF Redundancy is disabled. 'noMismatch' - Indicates no channels would be lost because there is no mismatch. 'backup2x4' - Indicates a loss of channels could occur on failover to the backup because the backup RF Port is in a 2x4 module and at least one primary RF Port is in a 2x8 module. 'primary2x4' - Indicates a loss of channels could occur on switch- back from the backup to the primary because the backup RF Port is in a 2x8 module and the primary RF Port is in a 2x4 module. This would occur if the failed 2x8 primary is replaced with a 2x4. 'any4x4' - Indicates a 4x4 QAM Module is installed in any slot and RF Redundancy is not available. Failover and/or switchback are suspended until the 4x4 is replaced. |
| INT apexQamRfRedundStatusRemConnection | 1.3.6.1.4.1.1166.1.31.8.2.7.1.5 | INTEGER | read-only | State of communication with REM. 'notApplicable' - QAM RF Redundancy is not enabled and/or the connection to the REM is not enabled. 'notConnected' - Initial condition. APEX has not sent a switch_port() message yet. 'connected' - received ack() message from REM for current switch_port() message. 'connectionLost' - REM has not replied to last 3 heartbeat switch_port() messages. |
| I32 apexQamRfRedundStatusRemError | 1.3.6.1.4.1.1166.1.31.8.2.7.1.6 | Integer32 | read-only | Status of REM1000 taken from error_code field in REM1000 ack() response (defined in REM1000 Message Stream Protocol). Valid only when apexQamRfRedundConfigRemConnection is other than 'none'. Values as defined in REM1000 MSP: 0x00 - No Errors. No problems switching, parsing switch_port() message, or with HW. 0x01 - Invalid apex_id value in prior switch_port() message. 0x02 - Invalid msg_type value in prior switch_port() message. 0x03 - Invalid port value in prior switch_port() message. 0x04 - Error switching after receiving valid switch_port() message. 0x05 - Minor HW error. REM can still switch. 0x81 - Apex_id Conflict. Switch_port() messages with the same apex_id have been received from multiple APEXs. Switch reset to pass- through configuration. 0x85 - Major HW error. REM failure. Switch reset to pass-through configuration. |
| I32 apexQamRfRedundStatusRemSwitch | 1.3.6.1.4.1.1166.1.31.8.2.7.1.7 | Integer32 | read-only | Status of the REM1000 switches indicated through ack() response from REM1000 (e.g. pass-through or switching port 'x'). Valid only when apexQamRfRedundConfigRemConnection is other than 'none'. Zero indicates REM is in passing inputs 1 to 5 straight through to outputs 1 to 5. Values of 1 to 5 indicate REM backup input port is switched to output port 1 to 5 and other ports are passed through. |
| I32 apexQamRfRedundStatusUdpPort | 1.3.6.1.4.1.1166.1.31.8.2.7.1.4 | Integer32 | read-only | UDP Port that is used for QAM RF Redundancy communication between the APEX and REM. When apexQamRfRedundConfigRemConnection is: 'direct' - APEX sends/receives broadcast on this UDP Port. 'common' - APEX sends/receives singlecast on this UDP Port. |
| apexQamStatus | 1.3.6.1.4.1.1166.1.31.8.2 | |||
| apexQamStatusGeneral | 1.3.6.1.4.1.1166.1.31.8.2.1 | |||
| INT apexQamStatusTransmissionMode | 1.3.6.1.4.1.1166.1.31.8.2.1.1 | INTEGER | read-only | This is the QAM Transmission Mode that is currently in use. QAM Transmission Mode is defined in: Series J: Transmission of Television, Sound Programme and other Multimedia Signals, ITU-T J.83. |
| apexQrmDownload | 1.3.6.1.4.1.1166.1.31.8.3 | |||
| apexQrmDownloadConfig | 1.3.6.1.4.1.1166.1.31.8.3.1 | |||
| apexQrmDownloadConfigEntry | 1.3.6.1.4.1.1166.1.31.8.3.1.2.1 | not-accessible | QAM Code Download Configuration Table Entry. | |
| apexQrmDownloadConfigGeneral | 1.3.6.1.4.1.1166.1.31.8.3.1.1 | |||
| I32 apexQrmDownloadConfigQrmNum | 1.3.6.1.4.1.1166.1.31.8.3.1.2.1.1 | Integer32 | not-accessible | QAM Code Download Configuration Table index. |
| INT apexQrmDownloadConfigRequest | 1.3.6.1.4.1.1166.1.31.8.3.1.2.1.2 | INTEGER | read-write | User initiated manual 4x4 QAM Module or 2x4/2x8 QAM Module QRM board Code Download request. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| apexQrmDownloadConfigTable | 1.3.6.1.4.1.1166.1.31.8.3.1.2 | not-accessible | Table of QAM Module Code Download Configuration. There are 2 QRM modules on each 2x4/2x8 QAM Module. QRMs in QAM Module slots are mapped to table rows as follows: Slot/QRM Table Row 1/1 1 1/2 2 2/1 3 2/2 4 3/1 5 3/2 6 4x4 QAM Modules do not use QRM boards. There is only one board. These will be found in the odd indexed rows of this table. The even indexed rows of the table are not used for 4x4 QAM Modules. 4x4 QAM Modules in QAM Module slots are mapped to table rows as follows: Slot Table Row 1 1 2 3 3 5 | |
| INT apexQrmDownloadFileSet | 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.6 | INTEGER | read-only | Indicates which file set will be used for this module. |
| I32 apexQrmDownloadProgress | 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.3 | Integer32 | read-only | Completion percentage of Code Download. '-1' indicates failure. |
| INT apexQrmDownloadRequired | 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.5 | INTEGER | read-only | Indicates if the module requires Code Download. Code download is needed if the versions are not up to date with the resident APEX FW Release. Refer to apexQamQrmRevisionTable, apexQamQrmRevisionStatusTable, and apexQrmDownloadFileSet for additional status. The user can initiate a manual download (apexQrmDownloadConfigRequest) when download 'notRequired'. |
| apexQrmDownloadStatus | 1.3.6.1.4.1.1166.1.31.8.3.2 | |||
| STR apexQrmDownloadStatusDescription | 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.2 | DisplayString | read-only | Text description of the current state of 4x4 QAM Module or 2x4/2x8 QAM Module QRM board Code Download. |
| apexQrmDownloadStatusEntry | 1.3.6.1.4.1.1166.1.31.8.3.2.2.1 | not-accessible | QRM Code Download Status Table Entry. | |
| apexQrmDownloadStatusGeneral | 1.3.6.1.4.1.1166.1.31.8.3.2.1 | |||
| I32 apexQrmDownloadStatusRfPortNum | 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.1 | Integer32 | not-accessible | QAM Code Download Status Table index. |
| apexQrmDownloadStatusTable | 1.3.6.1.4.1.1166.1.31.8.3.2.2 | not-accessible | Table of QAM Module Code Download Status. Refer to apexQrmDownloadConfigTable description for table indexing information. | |
| INT apexQrmDownloadSupported | 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.4 | INTEGER | read-only | Indicates if the module HW and SW will support Code Download. 'notSupported' if the module is unsupported or the code download might downgrade the code resident on the module. Refer to apexQamQrmRevisionTable, apexQamQrmRevisionStatusTable, and apexQrmDownloadFileSet for additional status. The user cannot initiate a manual download (apexQrmDownloadConfigRequest) when download 'notSupported'. |
| STR apexQrmFileRevCalibration | 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.3 | DisplayString | read-only | Revision of the Calibration data file of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Module QRM board file sets. Hex XXYY where XX is major version and YY is minor version. |
| STR apexQrmFileRevDateTime | 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.6 | DisplayString | read-only | Date and time the 4x4 QAM Module code file was created. Used only for 4x4 QAM Module file sets. Format: 'MM/DD/YYYY HH:MM' Where HH is a 24 hour clock. |
| I32 apexQrmFileRevFileSetNum | 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.1 | Integer32 | not-accessible | QAM file set number. |
| STR apexQrmFileRevFirmware | 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.2 | DisplayString | read-only | Revision of the Application firmware file of the 2x4/2x8 QAM Module's QRM board or revision of the Application firmware portion of the 4x4 QAM Module Code File. Hex XXYY where XX is major version and YY is minor version. |
| STR apexQrmFileRevFpga | 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.4 | DisplayString | read-only | Revision of FPGA firmware file of the 2x4/2x8 QAM Module's QRM board or revision of the FPGA1 firmware portion of the 4x4 QAM Module Code File. Hex XXYY where XX is major version and YY is minor version. |
| STR apexQrmFileRevFpga2 | 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.5 | DisplayString | read-only | Revision of FPGA2 firmware portion of the 4x4 QAM Module Code File. Used only for 4x4 QAM Module file sets. Hex XXYY where XX is major version and YY is minor version. |
| apexQrmFileRevisionEntry | 1.3.6.1.4.1.1166.1.31.8.3.2.3.1 | not-accessible | QRM File Revision Table Entry. | |
| apexQrmFileRevisionTable | 1.3.6.1.4.1.1166.1.31.8.3.2.3 | not-accessible | Table of revisions of QAM Module files released with the resident APEX FW Release. Refer to identSoftwareVersion in BCS-IDENT-MIB for the release number. | |
| apexRds | 1.3.6.1.4.1.1166.1.31.19 | |||
| I32 apexRdsCetNextPollTime | 1.3.6.1.4.1.1166.1.31.19.2.1.3 | Integer32 | read-only | Time in seconds until the next CET polling period. |
| I32 apexRdsCetPollInterval | 1.3.6.1.4.1.1166.1.31.19.1.1.4 | Integer32 | read-write | Interval that the APEX will use to poll for CSN/State information. After receiving the CSN/State information, the APEX will determine if it needs to retrieve new EMMs. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexRdsCetRefresh | 1.3.6.1.4.1.1166.1.31.19.1.1.5 | INTEGER | read-write | Setting to 'refresh' forces the APEX to retrieve new EMMs (APEX performs an EMM rollover sequence). Once written, the change to this parameter will take effect immediately. @Config(config=no, reboot=no) |
| C32 apexRdsCommErrorCount | 1.3.6.1.4.1.1166.1.31.19.2.1.8 | Counter32 | read-only | Count of total server communication errors. This parameter is set to 0 when the APEX boots up. |
| INT apexRdsCommStatus | 1.3.6.1.4.1.1166.1.31.19.2.1.9 | INTEGER | read-only | Status of communication with RDS. |
| apexRdsConfig | 1.3.6.1.4.1.1166.1.31.19.1 | |||
| APP apexRdsConfigApplyChange | 1.3.6.1.4.1.1166.1.31.19.1.1.11 | ApplyDataToDeviceTYPE | read-write | The Apply for RDS configuration items. This parameter MUST be set to 'apply' in order for any of the following to take effect: apexRdsIpAddr apexRdsTcpPort apexRdsPollRandomization apexRdsCetPollInterval apexRdsRmdPollInterval apexRdsProgramEpochDuration apexRdsConfigRds2Enable apexRdsConfigServerUrl This parameter MUST be set LAST after all associated parameters has been configured. @Config(config=no, reboot=no) |
| apexRdsConfigGeneral | 1.3.6.1.4.1.1166.1.31.19.1.1 | |||
| ENA apexRdsConfigRds2Enable | 1.3.6.1.4.1.1166.1.31.19.1.1.12 | EnableDisableTYPE | read-write | Indicates whether RDS-2 Interface is enabled or disabled. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| STR apexRdsConfigServerUrl | 1.3.6.1.4.1.1166.1.31.19.1.1.13 | DisplayString | read-write | Rights Data Server Uniform Resource Locator (RDS-2 Server URL). This is introduced to support RDS 2 Interface since APEX 2.5 release. The syntax of this parameter shall be: [http://][:]/ Note: 1. The 'http://' protocol part is default and optional, 2. 'RDS-2 Server IP' is Class A, B, or C IP address, 3. 'TCP Port' is optional, if not present, default to 80, 4. 'Server Root Directory Path' is not optional e.g. http://192.168.30.107:1020/rds/controller 192.168.30.107:1020/rds/controller 192.168.30.107/rds/controller (default port is 80) The apex host will validate this parameter upon applying change, and set the following three status parameter accordingly: - apexRdsStatusServerIp - apexRdsStatusServerPort - apexRdsStatusServerRootDirPath - apexRdsStatusValidation This parameter is not changed by apexRdsSetDefault. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexRdsConnectionStatus | 1.3.6.1.4.1.1166.1.31.19.2.1.1 | INTEGER | read-only | Rights Data Server connection status. |
| I32 apexRdsCurrentCsn | 1.3.6.1.4.1.1166.1.31.19.2.1.2 | Integer32 | read-only | This is the current CSN that the APEX is using for encrypting all programs. |
| I32 apexRdsEmmStatusCsn | 1.3.6.1.4.1.1166.1.31.19.2.2.1.2 | Integer32 | read-only | Category Sequence Number (CSN). |
| apexRdsEmmStatusEntry | 1.3.6.1.4.1.1166.1.31.19.2.2.1 | not-accessible | RDS EMM Status Table Entry. | |
| I32 apexRdsEmmStatusGpsTime | 1.3.6.1.4.1.1166.1.31.19.2.2.1.4 | Integer32 | read-only | This is the time in GPS seconds that this row was written. |
| I32 apexRdsEmmStatusIndex | 1.3.6.1.4.1.1166.1.31.19.2.2.1.1 | Integer32 | not-accessible | Index of EMM Status Table. Size of table can be found in apexRdsEmmStatusTableSize. |
| U32 apexRdsEmmStatusServerError | 1.3.6.1.4.1.1166.1.31.19.2.2.1.5 | Unsigned32 | read-only | This is the error code reported to the APEX by the RDS. Zero indicates no error. |
| INT apexRdsEmmStatusState | 1.3.6.1.4.1.1166.1.31.19.2.2.1.3 | INTEGER | read-only | Category Epoch Transition (CET) State. |
| apexRdsEmmStatusTable | 1.3.6.1.4.1.1166.1.31.19.2.2 | not-accessible | Table of the most recent RDS responses. | |
| I32 apexRdsEmmStatusTableSize | 1.3.6.1.4.1.1166.1.31.19.2.1.5 | Integer32 | read-only | EMM Status Table Size. This is the maximum number of rows in the EMM Status Table and is the limit on apexRdsEmmStatusIndex. |
| STR apexRdsEmmStatusUnitAddress | 1.3.6.1.4.1.1166.1.31.19.2.2.1.6 | DisplayString | read-only | This is the ACP address of the ACP associated with the error reported in apexRdsEmmStatusServerError. If no address is contained in this entry, the error applies to all ACPs or to the entire APEX. The address is made up of decimal digits formatted as ###-#####-#####-###. |
| RES apexRdsErrorCountReset | 1.3.6.1.4.1.1166.1.31.19.1.1.10 | ResetStatisticsTYPE | read-write | Resets RDS Communication error counts. Once written, the change to this parameter will take effect immediately. @Config(config=no, reboot=no) |
| INT apexRdsEventCcmAvailable | 1.3.6.1.4.1.1166.1.31.19.2.4.1.17 | INTEGER | read-only | The flag indicates that CCM (odd and even) is available for the associated epoch. |
| STR apexRdsEventControlByte | 1.3.6.1.4.1.1166.1.31.19.2.4.1.15 | DisplayString | read-only | The program control byte used in the PRKM (1 Hexadecimal byte). |
| apexRdsEventEntry | 1.3.6.1.4.1.1166.1.31.19.2.4.1 | not-accessible | Rds2 Events Table Entry. | |
| I32 apexRdsEventEpochEnd | 1.3.6.1.4.1.1166.1.31.19.2.4.1.5 | Integer32 | read-only | End time in GPS seconds of the returned program epoch. |
| I32 apexRdsEventEpochNumber | 1.3.6.1.4.1.1166.1.31.19.2.4.1.3 | Integer32 | read-only | Uniquely identifies a program epoch for the specified service. |
| I32 apexRdsEventEpochStart | 1.3.6.1.4.1.1166.1.31.19.2.4.1.4 | Integer32 | read-only | Start time in GPS seconds of the returned program epoch for the specified service. |
| I32 apexRdsEventEventIndex | 1.3.6.1.4.1.1166.1.31.19.2.4.1.2 | Integer32 | not-accessible | Rds Event Index. |
| I32 apexRdsEventInterstitialDuration | 1.3.6.1.4.1.1166.1.31.19.2.4.1.6 | Integer32 | read-only | The interstitial duration provides the time duration in seconds between the start of the program epoch and the start of the actual program or event. |
| I32 apexRdsEventNumberTiers | 1.3.6.1.4.1.1166.1.31.19.2.4.1.9 | Integer32 | read-only | A program can be associated with at most 7 tiers. |
| I32 apexRdsEventPreviewDuration | 1.3.6.1.4.1.1166.1.31.19.2.4.1.7 | Integer32 | read-only | The preview window provides the time duration in seconds between the start of the program epoch and the start of the pay portion of the program. |
| INT apexRdsEventPrkmWkemAvailable | 1.3.6.1.4.1.1166.1.31.19.2.4.1.16 | INTEGER | read-only | The flag indicates that PRKM, WKEM (odd and even) is available for the associated epoch. |
| I32 apexRdsEventProgramCost | 1.3.6.1.4.1.1166.1.31.19.2.4.1.11 | Integer32 | read-only | Represents the cost, in program units, of the program epoch. |
| I32 apexRdsEventProgramIndex | 1.3.6.1.4.1.1166.1.31.19.2.4.1.1 | Integer32 | not-accessible | apexRdsEventProgramIndex is the last 10 bits of apexOutputProgramEcmServiceId from apexOutputProgramTable. |
| I32 apexRdsEventPurchaseDuration | 1.3.6.1.4.1.1166.1.31.19.2.4.1.8 | Integer32 | read-only | The purchase window provides the time duration in seconds between the start of the program epoch that IPPV purchases are allowed. |
| STR apexRdsEventRatingData | 1.3.6.1.4.1.1166.1.31.19.2.4.1.13 | DisplayString | read-only | Program Rating Data in Hexadecimal format (3 bytes). Contains 6 rating dimensions where each rating dimension is a 4-bit integer that represents a different rating control for the region. A US region defines 4 rating dimensions: MPAA rating, violence content rating, language content rating and sexual content rating. |
| I32 apexRdsEventRatingRegion | 1.3.6.1.4.1.1166.1.31.19.2.4.1.12 | Integer32 | read-only | Identifies the Program Rating Region. The US region attribute is 0. |
| STR apexRdsEventRatingText | 1.3.6.1.4.1.1166.1.31.19.2.4.1.14 | DisplayString | read-only | Program Rating optionally contains a Rating Text. |
| apexRdsEventTable | 1.3.6.1.4.1.1166.1.31.19.2.4 | not-accessible | Table of Rds2 Events. The first index (apexRdsEventProgramIndex) matches to the same row index in the apexManualRouteTable. | |
| STR apexRdsEventTierData | 1.3.6.1.4.1.1166.1.31.19.2.4.1.10 | DisplayString | read-only | Program Tier Data in Hexadecimal format (28 bytes). Up to 7 tiers of information are provided for each program. Tier information for each program consists of 4 bytes. First 3 bytes are the Tier Value, next 1 bytes are the Tier Type. |
| C32 apexRdsFlashWriteCount | 1.3.6.1.4.1.1166.1.31.19.2.1.10 | Counter32 | read-only | Running count of the number of flash memory erasures/writes. |
| I32 apexRdsInitialEcmRetryInterval | 1.3.6.1.4.1.1166.1.31.19.1.1.14 | Integer32 | read-write | This parameter is used to configure RDS2 server ECM retry time. This value defines when the next retry will be performed by the host. Units are seconds. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexRdsIpAddr | 1.3.6.1.4.1.1166.1.31.19.1.1.1 | IpAddress | read-write | Rights Data Server IP address. Class A, B, or C IP address of the RDS. Changing this parameter will cause the APEX to perform an EMM rollover sequence. This parameter is not changed by apexRdsSetDefault. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| U32 apexRdsMcast16 | 1.3.6.1.4.1.1166.1.31.19.2.1.11 | Unsigned32 | read-only | Multicast-16 bit address used for build PRK messages. The multicast-16 bit address is from the EMMs received. |
| I32 apexRdsPollRandomization | 1.3.6.1.4.1.1166.1.31.19.1.1.8 | Integer32 | read-write | RDS Polling Randomization Time. Maximum time in minutes to delay polling at startup in order to avoid having many APEXs polling the RDS simultaneously. The actual delay time will be randomly calculated by the APEX and will be no greater than this value. A value of zero means no delay and the APEX will poll immediately at startup. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexRdsProgramEpochDuration | 1.3.6.1.4.1.1166.1.31.19.1.1.3 | Integer32 | read-write | The Program Epoch Duration in minutes. Changes are not applied until the end of the current epoch. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| C32 apexRdsProgramMessagesFailed | 1.3.6.1.4.1.1166.1.31.19.2.1.7 | Counter32 | read-only | Number of failed ServiceEncrypt messages received in the last 15 minutes. |
| C32 apexRdsProgramMessagesReceivedEx | 1.3.6.1.4.1.1166.1.31.19.2.1.6 | Counter32 | read-only | Number of successful ServiceEncrypt messages received in the last 15 minutes. |
| I32 apexRdsRmdNextPollTime | 1.3.6.1.4.1.1166.1.31.19.2.1.4 | Integer32 | read-only | Time in seconds until the next RMD polling period. |
| I32 apexRdsRmdPollInterval | 1.3.6.1.4.1.1166.1.31.19.1.1.6 | Integer32 | read-write | Interval that the APEX will use to poll for RMD information. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexRdsRmdRefresh | 1.3.6.1.4.1.1166.1.31.19.1.1.7 | INTEGER | read-write | Setting to 'refresh' forces the APEX to retrieve new RMD data from RDS server. Once written, the change to this parameter will take effect immediately. @Config(config=no, reboot=no) |
| INT apexRdsSetDefault | 1.3.6.1.4.1.1166.1.31.19.1.1.9 | INTEGER | read-write | This parameter sets apexRdsCetPollInterval, apexRdsPollRandomization, apexRdsTcpPort, apexRdsRmdPollInterval, apexRdsProgramEpochDuration and apexRdsInitialEcmRetryInterval to default values. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'.. @Config(config=no, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) |
| STR apexRdsSourceLookupDescription | 1.3.6.1.4.1.1166.1.31.19.2.3.1.2 | DisplayString | read-only | Text Description of the service provided by the Rights Data Server. |
| apexRdsSourceLookupEntry | 1.3.6.1.4.1.1166.1.31.19.2.3.1 | not-accessible | Source Lookup Table Entry. | |
| I32 apexRdsSourceLookupIndex | 1.3.6.1.4.1.1166.1.31.19.2.3.1.1 | Integer32 | not-accessible | Source Lookup Table Index. |
| I32 apexRdsSourceLookupProviderId | 1.3.6.1.4.1.1166.1.31.19.2.3.1.4 | Integer32 | read-only | Provider Id of the service. |
| I32 apexRdsSourceLookupSourceId | 1.3.6.1.4.1.1166.1.31.19.2.3.1.3 | Integer32 | read-only | Source Id of the service. |
| apexRdsSourceLookupTable | 1.3.6.1.4.1.1166.1.31.19.2.3 | not-accessible | This table provides a list of Source IDs and Provider IDs along with an associated string. This table of information is provided by the RDS to make it easier for a user to figure out the Source ID and Provider ID for a particular service. | |
| apexRdsStatus | 1.3.6.1.4.1.1166.1.31.19.2 | |||
| apexRdsStatusGeneral | 1.3.6.1.4.1.1166.1.31.19.2.1 | |||
| IP apexRdsStatusServerIp | 1.3.6.1.4.1.1166.1.31.19.2.1.12 | IpAddress | read-only | Effective Rights Data Server IP address. Derived from RDS Server URL. This is set to 0.0.0.0 when validation on RDS Server URL fails. See apexRdsConfigServerUrl. |
| I32 apexRdsStatusServerPort | 1.3.6.1.4.1.1166.1.31.19.2.1.13 | Integer32 | read-only | Effective Rights Data Server TCP port. Derived from RDS Server URL. This is set to 0 when validation on RDS Server URL fails. See apexRdsConfigServerUrl. |
| STR apexRdsStatusServerRootDirPath | 1.3.6.1.4.1.1166.1.31.19.2.1.14 | DisplayString | read-only | Effective Rights Data Server Root Directory Path. Derived from RDS Server URL. This is set to Null String when validation on RDS Server URL fails. See apexRdsConfigServerUrl. |
| INT apexRdsStatusValidation | 1.3.6.1.4.1.1166.1.31.19.2.1.15 | INTEGER | read-only | Indicates whether the current RDS Server URL parameter is valid. urlValid (1) - RDS-2 URL is valid, missingIpOrPath (2) - RDS-2 IP or Root Path is missing, emptyRootPath (3) - RDS-2 Root Path cannot be empty, invalidTcpPort (4) - RDS-2 TCP Port ranges from 1~65535, default to 80, invalidIpClass (5) - RDS-2 IP shall be class A/B/C. See apexRdsConfigServerUrl. |
| I32 apexRdsTcpPort | 1.3.6.1.4.1.1166.1.31.19.1.1.2 | Integer32 | read-write | Rights Data Server TCP port. Changing this parameter will cause the APEX to perform an EMM rollover sequence. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexRpc | 1.3.6.1.4.1.1166.1.31.9.3 | |||
| APP apexRpcApplyChange | 1.3.6.1.4.1.1166.1.31.9.3.1.1.8 | ApplyDataToDeviceTYPE | read-write | The Apply for RPC Settings. This applies to apexRpcControlInterface, apexRpcNumShellSessions, apexRpcRfPortServiceGroup. @Config(config=no, reboot=no) |
| ENA apexRpcAvgBandwidthEnable | 1.3.6.1.4.1.1166.1.31.9.3.1.1.7 | EnableDisableTYPE | read-write | When enabled the APEX populates the sessionRate in the QuerySessionInfo Response message with groupRate divided by the number of sessionIds in the group. The value reported makes no distinction between bound and unbound sessions. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| apexRpcConfig | 1.3.6.1.4.1.1166.1.31.9.3.1 | |||
| apexRpcConfigGeneral | 1.3.6.1.4.1.1166.1.31.9.3.1.1 | |||
| NUM apexRpcControlInterface | 1.3.6.1.4.1.1166.1.31.9.3.1.1.5 | EthernetInterfaceTYPE | read-write | The Enet interface that will be used to set the IP address attribute in the generated XML file. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will only take immediate effect after apexRpcApplyChange is changed to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRpcApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| I32 apexRpcDataCarouselProgram | 1.3.6.1.4.1.1166.1.31.9.3.1.1.1 | Integer32 | read-write | Indicates which Input Program Number to use for the Data Carousel. The data carousel in SDV mode (RPC or RTSP) is on a fixed PMT PID along with a fixed component PID. In order to maintain these PID values, the APEX will check for a specific input service number defined by this parameter. This service mapping is assumed to be the Data Carousel mapping. The APEX will maintain the PMT PID value along with the component PID value. To facilitate this mapping, the Data Carousel input/output program number is configurable. - Data Carousel Service Number Default: 0xF38F (62351) The PMT PID and component PID will be determined by the APEX by analyzing the PAT and PMT based on the program number configured. A program number of zero (0) indicates that there is no data carousel. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| STR apexRpcDeviceName | 1.3.6.1.4.1.1166.1.31.9.3.1.1.3 | DisplayString | read-write | The device name of this APEX. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| STR apexRpcDeviceType | 1.3.6.1.4.1.1166.1.31.9.3.1.1.4 | DisplayString | read-write | The device type string reported in XML configuration file. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| I32 apexRpcNumShellSessions | 1.3.6.1.4.1.1166.1.31.9.3.1.1.6 | Integer32 | read-write | The number of shell sessions to be created on each channel marked for session control mode. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will only take immediate effect after apexRpcApplyChange is changed to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRpcApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| apexRpcQamStatEntry | 1.3.6.1.4.1.1166.1.31.9.3.2.3.1 | not-accessible | RPC Switched Digital Video QAM Status Table Entry. | |
| I32 apexRpcQamStatNumSdvSessions | 1.3.6.1.4.1.1166.1.31.9.3.2.3.1.2 | Integer32 | read-only | The Number of reserved SDV sessions on this QAM Channel. This is the number of SDV sessions that have been reserved by the manager. Each SDV session requires that a manager reserve a QAM. This is the count of SDV sessions reserved (not the actual number of active SDV sessions). |
| I32 apexRpcQamStatNumVodBcSessions | 1.3.6.1.4.1.1166.1.31.9.3.2.3.1.3 | Integer32 | read-only | The Number of VOD/Broadcast sessions on this QAM Channel. This is the number of VOD/Broadcast sessions active on a QAM Channel. Since VOD and Broadcast sessions are not required to be reserved for an output, this is the count of active VOD and Broadcast sessions on a specific QAM. |
| I32 apexRpcQamStatQamChannelNum | 1.3.6.1.4.1.1166.1.31.9.3.2.3.1.1 | Integer32 | not-accessible | The RPC Switched Digital Video QAM Status table index. |
| U32 apexRpcQamStatSdvGroupBandwidth | 1.3.6.1.4.1.1166.1.31.9.3.2.3.1.4 | Unsigned32 | read-only | The Group BW for SDV sessions (not used for VOD/Broadcast sessions). This is the total amount of BW allocated for all SDV sessions on a channel. The total SDV BW for a channel is defined by the session manager. The manager reserves this BW for future SDV sessions. This is not the BW of current active SDV sessions, but the total BW reserved by the manager for SDV sessions. |
| apexRpcQamStatTable | 1.3.6.1.4.1.1166.1.31.9.3.2.3 | not-accessible | Table of RPC Switched Digital Video QAM status. This table is indexed by output stream number and 48 rows. | |
| ENA apexRpcReportAllSessions | 1.3.6.1.4.1.1166.1.31.9.3.1.1.2 | EnableDisableTYPE | read-write | Session reporting mode. Indicates what sessions will be reported when the APEX is requested to report sessions to a manager. When 'enabled', the APEX will report all sessions. When 'disabled', the APEX will report only the sessions for the requesting manager. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| apexRpcRfChannelEntry | 1.3.6.1.4.1.1166.1.31.9.3.1.3.1 | not-accessible | RPC RF Channel Configuration Table Entry. | |
| STR apexRpcRfChannelName | 1.3.6.1.4.1.1166.1.31.9.3.1.3.1.2 | DisplayString | read-write | The name of this RF Channel. |
| I32 apexRpcRfChannelNum | 1.3.6.1.4.1.1166.1.31.9.3.1.3.1.1 | Integer32 | not-accessible | The RF Channel number. |
| apexRpcRfChannelTable | 1.3.6.1.4.1.1166.1.31.9.3.1.3 | not-accessible | Table of Configuration data for RPC Session RF Channels. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') | |
| apexRpcRfPortEntry | 1.3.6.1.4.1.1166.1.31.9.3.1.2.1 | not-accessible | RPC RF Port Configuration Table Entry. | |
| STR apexRpcRfPortName | 1.3.6.1.4.1.1166.1.31.9.3.1.2.1.2 | DisplayString | read-write | The RF Port name. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| I32 apexRpcRfPortNum | 1.3.6.1.4.1.1166.1.31.9.3.1.2.1.1 | Integer32 | not-accessible | The RF Port number. |
| U32 apexRpcRfPortServiceGroup | 1.3.6.1.4.1.1166.1.31.9.3.1.2.1.3 | Unsigned32 | read-write | The RF Port service group. Once written, the change to this parameter will only take immediate effect after apexRpcApplyChange is changed to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRpcApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| apexRpcRfPortTable | 1.3.6.1.4.1.1166.1.31.9.3.1.2 | not-accessible | Table of Configuration data for RPC Session RF Ports. This variable is only used to generate an XML configuration file via the EM. | |
| apexRpcSessionStatEntry | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1 | not-accessible | RPC Switched Digital Video Session Status Table Entry. | |
| I32 apexRpcSessionStatIndex | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.1 | Integer32 | not-accessible | The RPC Switched Digital Video Session Status table index. |
| I32 apexRpcSessionStatInputProgramNum | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.3 | Integer32 | read-only | The Gigabit Ethernet Input Program Number. A value of zero (0) indicates that the input is an SPTS and the first program listed in the input PAT will be mapped by the APEX. |
| I32 apexRpcSessionStatInputTsIndex | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.2 | Integer32 | read-only | The index into the apexInputTsStatTable. |
| IP apexRpcSessionStatManagerIpAddr | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.12 | IpAddress | read-only | The IP address of the RPC SDV, VOD, or Broadcast manager sending session commands. |
| I32 apexRpcSessionStatOutputProgramNum | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.6 | Integer32 | read-only | The Output Program Number (1 - 65535). |
| I32 apexRpcSessionStatOutputQamChannel | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.5 | Integer32 | read-only | The Output QAM Channel. |
| I32 apexRpcSessionStatProgramBandwidth | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.7 | Integer32 | read-only | The Expected Program Bandwidth (bps). This is the bandwidth of the program as defined in the service mapping. A value of 0 indicates that the program BW is unknown. |
| U32 apexRpcSessionStatSessionIdWord1 | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.9 | Unsigned32 | read-only | The Session ID Word 1. Session IDs are 10 byte character arrays. Session IDs are be stored as 3 4-byte words (3 ulongs) in this MIB. First 2 Bytes are always 0, next 10 contain the session ID. Session ID is broken up as follows: Word 1: 00:01 = 0x0000 (unused) Word 1: 02:03 = 1st 2 bytes of session ID (1st 2 bytes of MAC address) Word 2: 00:03 = Next 4 bytes (these 4 plus 1st 2 are the MAC address of manager) Word 3: 00:03 = Last 4 bytes (unique number assigned by manager) |
| U32 apexRpcSessionStatSessionIdWord2 | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.10 | Unsigned32 | read-only | The Session ID Word 2. Session IDs are 10 byte character arrays. Session IDs are be stored as 3 4-byte words (3 Unsigned32) in this MIB. First 2 Bytes are always 0, next 10 contain the session ID. Session ID is broken up as follows: Word 1: 00:01 = 0x0000 (unused) Word 1: 02:03 = 1st bytes of session ID (1st 2 bytes of MAC address) Word 2: 00:03 = Next 4 bytes (these 4 plus 1st 2 are the MAC address of manager) Word 3: 00:03 = Last 4 bytes (unique number assigned by manager) |
| U32 apexRpcSessionStatSessionIdWord3 | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.11 | Unsigned32 | read-only | The Session ID Word 3. Session IDs are 10 byte character arrays. Session IDs are be stored as 3 4-byte words (3 Unsigned32) in this MIB. First 2 Bytes are always 0, next 10 contain the session ID. Session ID is broken up as follows: Word 1: 00:01 = 0x0000 (unused) Word 1: 02:03 = 1st bytes of session ID (1st 2 bytes of MAC address) Word 2: 00:03 = Next 4 bytes (these 4 plus 1st 2 are the MAC address of manager) Word 3: 00:03 = Last 4 bytes (unique number assigned by manager) |
| INT apexRpcSessionStatSessionType | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.8 | INTEGER | read-only | The Type of session (SDV binding or VOD/Broadcast session). 1 = Switched Digital Video (SDV) 2 = VOD or Broadcast |
| IP apexRpcSessionStatSourceIpAddr3 | 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.4 | IpAddress | read-only | The Gigabit Ethernet IGMP v3 Source IP Address 3. This IP address is currently unsupported by the APEX. |
| apexRpcSessionStatTable | 1.3.6.1.4.1.1166.1.31.9.3.2.2 | not-accessible | Table of RPC Switched Digital Video Session status. This table contains 1 row up to the maximum number of service mappings supported. | |
| apexRpcStatus | 1.3.6.1.4.1.1166.1.31.9.3.2 | |||
| apexRpcStatusGeneral | 1.3.6.1.4.1.1166.1.31.9.3.2.1 | |||
| apexRtsp | 1.3.6.1.4.1.1166.1.31.9.4 | |||
| APP apexRtspConfControllerApplyChange | 1.3.6.1.4.1.1166.1.31.9.4.1.2.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for a row of data in apexRtspConfControllerTable and apexRtspConfControlNamesTable. A row in this table corresponds to the same row index in the apexRtspConfControllerTable and apexRtspConfControlNamesTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no) |
| apexRtspConfControllerApplyEntry | 1.3.6.1.4.1.1166.1.31.9.4.1.2.1 | not-accessible | RTSP Controller Configuration Apply Table Entry. | |
| I32 apexRtspConfControllerApplyNum | 1.3.6.1.4.1.1166.1.31.9.4.1.2.1.1 | Integer32 | not-accessible | The RTSP Session Controller number. |
| apexRtspConfControllerApplyTable | 1.3.6.1.4.1.1166.1.31.9.4.1.2 | not-accessible | Table of Apply Change for the data for apexRtspConfControllerTable. A row of this table corresponds to a row in apexRtspConfControllerTable. | |
| I32 apexRtspConfControllerBandwidthDelta | 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.5 | Integer32 | read-write | The Bandwidth Delta, in kilobits per second (kbps), for sending an Update Message. Whenever a QAM Channel's output utilization changes by more than the bandwidth delta, the APEX will send a update message providing the current BW being utilized. Zero indicates that the APEX should not send update messages based on bandwidth changes. |
| apexRtspConfControllerEntry | 1.3.6.1.4.1.1166.1.31.9.4.1.3.1 | not-accessible | RTSP Controller Configuration Table Entry. | |
| I32 apexRtspConfControllerHoldTime | 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.4 | Integer32 | read-write | The session hold time in seconds. If the APEX does not receive a keep session alive message from the controller in this time the APEX will close the session. The APEX will transmit keep session alive messages at one-third of this time. Zero indicates that the APEX should not send keep session alive messages. |
| IP apexRtspConfControllerIp | 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.2 | IpAddress | read-write | The IP Address of the RTSP session controller. |
| I32 apexRtspConfControllerNum | 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.1 | Integer32 | not-accessible | The Controller Number. APEX currently supports only one controller. |
| I32 apexRtspConfControllerPort | 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.3 | Integer32 | read-write | Port for the RTSP session controller. |
| apexRtspConfControllerTable | 1.3.6.1.4.1.1166.1.31.9.4.1.3 | not-accessible | Table of RTSP configuration items configurable on a Controller basis. Once written, the change to this table will only take immediate effect after apexRtspConfControllerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfControllerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') | |
| STR apexRtspConfControlNamesDeviceName | 1.3.6.1.4.1.1166.1.31.9.4.1.4.1.3 | DisplayString | read-write | The device name of this APEX. |
| apexRtspConfControlNamesEntry | 1.3.6.1.4.1.1166.1.31.9.4.1.4.1 | not-accessible | RTSP Controller Names Configuration Table Entry. | |
| I32 apexRtspConfControlNamesNum | 1.3.6.1.4.1.1166.1.31.9.4.1.4.1.1 | Integer32 | not-accessible | The Controller Number. APEX currently supports only one controller. |
| STR apexRtspConfControlNamesStreamingZone | 1.3.6.1.4.1.1166.1.31.9.4.1.4.1.2 | DisplayString | read-write | The streaming zone that the APEX is a member of. |
| apexRtspConfControlNamesTable | 1.3.6.1.4.1.1166.1.31.9.4.1.4 | not-accessible | Table of RTSP configuration items configurable on a Controller basis. Contains the control names. This table is a row-for-row index match to the apexRtspConfControllerTable. Once written, the change to this table will only take immediate effect after apexRtspConfControllerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfControllerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') | |
| apexRtspConfGbeEdgeGroupEntry | 1.3.6.1.4.1.1166.1.31.9.4.1.7.1 | not-accessible | RTSP GigE Edge Group Configuration Table Entry. | |
| STR apexRtspConfGbeEdgeGroupName | 1.3.6.1.4.1.1166.1.31.9.4.1.7.1.2 | DisplayString | read-write | The Name of this GigE Interface. |
| I32 apexRtspConfGbeEdgeGroupNum | 1.3.6.1.4.1.1166.1.31.9.4.1.7.1.1 | Integer32 | not-accessible | The GigE Edge Group Interface number. |
| apexRtspConfGbeEdgeGroupTable | 1.3.6.1.4.1.1166.1.31.9.4.1.7 | not-accessible | Table of Configuration data for RTSP Session GigE Interfaces. Once written, the change to this table will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') | |
| apexRtspConfig | 1.3.6.1.4.1.1166.1.31.9.4.1 | |||
| apexRtspConfigGeneral | 1.3.6.1.4.1.1166.1.31.9.4.1.1 | |||
| I32 apexRtspConfMhaAddressDomain | 1.3.6.1.4.1.1166.1.31.9.4.1.8.1.2 | Integer32 | read-write | Address Domain of the sender used in ERRP. Address Domain of the ERM and APEX must match in order to establish an ERRP connection. Zero is used as the global address domain, which is interpreted to mean that any advertised address can be reached from any address domain. |
| apexRtspConfMhaEntry | 1.3.6.1.4.1.1166.1.31.9.4.1.8.1 | not-accessible | MHA RTSP Configuration Table Entry. | |
| apexRtspConfMhaGeneral | 1.3.6.1.4.1.1166.1.31.9.4.1.9 | |||
| I32 apexRtspConfMhaNum | 1.3.6.1.4.1.1166.1.31.9.4.1.8.1.1 | Integer32 | not-accessible | The MHA Controller Number. APEX currently supports only one controller. |
| I32 apexRtspConfMhaPort | 1.3.6.1.4.1.1166.1.31.9.4.1.8.1.3 | Integer32 | read-write | Port for the MHA session controller. |
| apexRtspConfMhaSbe | 1.3.6.1.4.1.1166.1.31.9.4.1.10 | |||
| APP apexRtspConfMhaSbeApplyChange | 1.3.6.1.4.1.1166.1.31.9.4.1.10.5 | ApplyDataToDeviceTYPE | read-write | The Apply for the MHA session based encryption settings. This parameter MUST be set to 'apply' in order for any of the data in MHA SBE to take effect in the APEX. This parameter MUST be set LAST after all other data in the MHA SBE has been configured. @Config(config=no, reboot=no) |
| INT apexRtspConfMhaSbeApsLevel | 1.3.6.1.4.1.1166.1.31.9.4.1.10.3 | INTEGER | read-write | Analog Protection System (APS) Level setting for session based PRK messages if APS is not defined in the XML encryption blob. Defines what copy protection encoding will be applied to the analog composite output by the settop box. - notDefined - analog protection is not defined, settop box applications can configure APS - off - no analog protection - splitBurstOff - AGC on, split burst off - splitBurst2Line - AGC on, 2 line split burst on - splitBurst4Line - AGC on, 4 line split burst on Once written, the change to this parameter will only take immediate effect after apexRtspConfMhaSbeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfMhaSbeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| INT apexRtspConfMhaSbeCciLevel | 1.3.6.1.4.1.1166.1.31.9.4.1.10.2 | INTEGER | read-write | Copy Control Information (CCI) Level setting for session based PRK messages if CCI is not defined in the XML encryption blob. - notDefined - CCI is not defined, settop box applications can configure CCI - copyFreely - program can be copied - copyOnce - program can be copied once - copyNever - program can never be copied - noMoreCopies - Once written, the change to this parameter will only take immediate effect after apexRtspConfMhaSbeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfMhaSbeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| INT apexRtspConfMhaSbeCitSetting | 1.3.6.1.4.1.1166.1.31.9.4.1.10.4 | INTEGER | read-write | Copy protection Constraint Image Trigger setting. This is only applicable when the session is being encrypted and the CIT setting was not contained in the XML encryption blob. Once written, the change to this parameter will only take immediate effect after apexRtspConfMhaSbeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfMhaSbeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| INT apexRtspConfMhaSbeEncryptionMode | 1.3.6.1.4.1.1166.1.31.9.4.1.10.1 | INTEGER | read-write | This parameter is used to set the Session based Encryption Mode. It applies to all session based encryption sessions. - 'full' - The APEX will use Full encryption. - 'fwk' - The APEX will use Fixed Working Key (FWK) encryption. - 'fpk' - The APEX will use Fixed Program Key (FPK) encryption. The APEX will not attempt to get EMMs. Once written, the change to this parameter will only take immediate effect after apexRtspConfMhaSbeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfMhaSbeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| apexRtspConfMhaTable | 1.3.6.1.4.1.1166.1.31.9.4.1.8 | not-accessible | Table of MHA RTSP configuration items configurable on a Controller basis. Once written, the change to this table will only take immediate effect after apexRtspConfControllerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfControllerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') | |
| ENA apexRtspConfMhaUdpMapEnable | 1.3.6.1.4.1.1166.1.31.9.4.1.9.1 | EnableDisableTYPE | read-write | Indicates if the UDP Map is populated in the Update message sent by the APEX to the ERM when in MHA mode. When 'enabled', the APEX will report UDP ports available. When 'disabled', the APEX will include the UDP Map field but will not populate it with data. Once written, the change to this table will only take immediate effect after apexRtspConfControllerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfControllerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| APP apexRtspConfQamChannelApplyChange | 1.3.6.1.4.1.1166.1.31.9.4.1.5.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for a row of data in apexRtspConfQamChannelTable. A row in this table corresponds to the same row index in the apexRtspConfQamChannelTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no) |
| apexRtspConfQamChannelApplyEntry | 1.3.6.1.4.1.1166.1.31.9.4.1.5.1 | not-accessible | RTSP QAM Configuration Apply Table Entry. | |
| I32 apexRtspConfQamChannelApplyNum | 1.3.6.1.4.1.1166.1.31.9.4.1.5.1.1 | Integer32 | not-accessible | The QAM Channel number. |
| apexRtspConfQamChannelApplyTable | 1.3.6.1.4.1.1166.1.31.9.4.1.5 | not-accessible | Table of Apply Change for the data for apexRtspConfQamChannelTable. A row of this table corresponds to a row in apexRtspConfQamChannelTable. | |
| apexRtspConfQamChannelEntry | 1.3.6.1.4.1.1166.1.31.9.4.1.6.1 | not-accessible | RTSP QAM Configuration Table Entry. | |
| STR apexRtspConfQamChannelGroupName | 1.3.6.1.4.1.1166.1.31.9.4.1.6.1.2 | DisplayString | read-write | The QAM Group Name that this QAM Channel is a member of. |
| I32 apexRtspConfQamChannelNum | 1.3.6.1.4.1.1166.1.31.9.4.1.6.1.1 | Integer32 | not-accessible | The QAM Channel number. |
| apexRtspConfQamChannelTable | 1.3.6.1.4.1.1166.1.31.9.4.1.6 | not-accessible | Table of Configuration data for RTSP Session QAM Channels. Once written, the change to this table will only take immediate effect after apexRtspConfQamChannelApplyChange to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfQamChannelApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') | |
| IP apexRtspEventControllerIp | 1.3.6.1.4.1.1166.1.31.200.5.1.3 | IpAddress | read-only | IP address of the RTSP Controller associated with this event. Value will be zero if the event is not associated with a specific controller. Refer to apexRtspEventSourceDescription for the source of the event. |
| STR apexRtspEventDescription | 1.3.6.1.4.1.1166.1.31.200.5.1.6 | DisplayString | read-only | Text description of the event. |
| apexRtspEventEntry | 1.3.6.1.4.1.1166.1.31.200.5.1 | not-accessible | RTSP Event Table Entry. | |
| I32 apexRtspEventIndex | 1.3.6.1.4.1.1166.1.31.200.5.1.1 | Integer32 | not-accessible | Index to RTSP Event table entry. |
| I32 apexRtspEventSessionCount | 1.3.6.1.4.1.1166.1.31.200.5.1.4 | Integer32 | read-only | Number of active sessions for the RTSP Controller associated with this event. Value will be total count of all sessions for all controllers if the event is not associated with a specific controller. Refer to apexRtspEventSourceDescription for the source of the event. |
| STR apexRtspEventSourceDescription | 1.3.6.1.4.1.1166.1.31.200.5.1.5 | DisplayString | read-only | Text description of the source of the event. May indicate a controller identifier or an APEX application process. |
| apexRtspEventTable | 1.3.6.1.4.1.1166.1.31.200.5 | not-accessible | Table of RTSP Events that have occurred. Maximum of 100 events will be recorded. | |
| I32 apexRtspEventTimeLogged | 1.3.6.1.4.1.1166.1.31.200.5.1.2 | Integer32 | read-only | Time in GPS seconds (apexSystemTime) that this event was logged. |
| U32 apexRtspQamStatAllocatedBandwidth | 1.3.6.1.4.1.1166.1.31.9.4.2.4.1.3 | Unsigned32 | read-only | This is the total amount of BW allocated for all sessions on a channel. |
| apexRtspQamStatEntry | 1.3.6.1.4.1.1166.1.31.9.4.2.4.1 | not-accessible | RTSP Session QAM status Table Entry. | |
| I32 apexRtspQamStatNumSessions | 1.3.6.1.4.1.1166.1.31.9.4.2.4.1.2 | Integer32 | read-only | The Number of active sessions on this QAM Channel. |
| I32 apexRtspQamStatQamChannelNum | 1.3.6.1.4.1.1166.1.31.9.4.2.4.1.1 | Integer32 | not-accessible | The RTSP Session Control Video QAM Status table index. |
| apexRtspQamStatTable | 1.3.6.1.4.1.1166.1.31.9.4.2.4 | not-accessible | Table of RTSP Session QAM status. This table is indexed by QAM channel number and contains 48 rows. | |
| INT apexRtspReportGbeInterfaces | 1.3.6.1.4.1.1166.1.31.9.4.1.1.1 | INTEGER | read-write | This selects which pair of GBE interfaces are to be reported to the RTSP controller (ERM) via VREP. The pairedPortAssignment selection allows for both pairs of GBE interfaces to be reported to the ERM. This allows for all 4 GBE interfaces to be used by the ERM for session mappings. This effectively splits the APEX into 2x24 QAM devices where the first GBE interface pair (1&2) are assigned to the first 24 output QAM streams (output TS 1 - 24) and the second GBE pair (3&4) are assigned to the second 24 output QAM streams (output TS 25-48). Selecting reportGbe1and2 or reportGbe3and4 limits the ERM to 2 GBE interfaces only. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| STR apexRtspSessionId | 1.3.6.1.4.1.1166.1.31.9.4.2.3.1.2 | DisplayString | read-only | The Session ID. |
| apexRtspSessionIdEntry | 1.3.6.1.4.1.1166.1.31.9.4.2.3.1 | not-accessible | RTSP Session ID Table Entry. | |
| I32 apexRtspSessionIdIndex | 1.3.6.1.4.1.1166.1.31.9.4.2.3.1.1 | Integer32 | not-accessible | The RTSP Session ID table index. This is a row-for-row match to the RTSP Session Status table index. |
| apexRtspSessionIdTable | 1.3.6.1.4.1.1166.1.31.9.4.2.3 | not-accessible | Table of RTSP Session Ids. This table contains 768 rows and is a row-for-row index match to apexRtspSessionStatTable. | |
| apexRtspSessionStatEntry | 1.3.6.1.4.1.1166.1.31.9.4.2.2.1 | not-accessible | RTSP Session Status Table Entry. | |
| I32 apexRtspSessionStatIndex | 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.1 | Integer32 | not-accessible | The RTSP Session Status table index. |
| I32 apexRtspSessionStatInputProgramNum | 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.3 | Integer32 | read-only | The Gigabit Ethernet Input Program Number. A value of zero (0) indicates that the input is an SPTS and the first program listed in the input PAT will be mapped by the APEX. |
| I32 apexRtspSessionStatInputTsIndex | 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.2 | Integer32 | read-only | The index into the apexInputTsStatTable. |
| IP apexRtspSessionStatManagerIpAddr | 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.7 | IpAddress | read-only | The IP address of the manager sending session commands. |
| I32 apexRtspSessionStatOutputProgramNum | 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.5 | Integer32 | read-only | The Output Program Number. |
| I32 apexRtspSessionStatOutputQamChannel | 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.4 | Integer32 | read-only | The Output QAM Channel. |
| I32 apexRtspSessionStatProgramBandwidth | 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.6 | Integer32 | read-only | The Expected Program Bandwidth (bps). This is the bandwidth of the program as defined in the service mapping. A value of 0 indicates that the program BW is unknown. |
| apexRtspSessionStatTable | 1.3.6.1.4.1.1166.1.31.9.4.2.2 | not-accessible | Table of RTSP Session status. This table contains 768 rows. | |
| INT apexRtspStatControllerCommFault | 1.3.6.1.4.1.1166.1.31.9.4.2.5.1.4 | INTEGER | read-only | Current fault condition of apexRtspStatControllerConnection. This is the apexAlarmRtspControllerCommFault level for this controller. |
| INT apexRtspStatControllerConnection | 1.3.6.1.4.1.1166.1.31.9.4.2.5.1.3 | INTEGER | read-only | Status of the connection between the APEX and the Controller. 'notConnected' causes apexAlarmRtspControllerCommFault. |
| INT apexRtspStatControllerDiscovery | 1.3.6.1.4.1.1166.1.31.9.4.2.5.1.2 | INTEGER | read-only | Status of Controller to APEX discovery. |
| apexRtspStatControllerEntry | 1.3.6.1.4.1.1166.1.31.9.4.2.5.1 | not-accessible | RTSP Controller Status Table Entry. | |
| I32 apexRtspStatControllerNum | 1.3.6.1.4.1.1166.1.31.9.4.2.5.1.1 | Integer32 | not-accessible | The Controller Number. APEX currently supports only one controller. |
| apexRtspStatControllerTable | 1.3.6.1.4.1.1166.1.31.9.4.2.5 | not-accessible | Table of RTSP status items configurable on a Controller basis. | |
| apexRtspStatQamChannelEntry | 1.3.6.1.4.1.1166.1.31.9.4.2.6.1 | not-accessible | RTSP QAM Configuration Table Entry. | |
| STR apexRtspStatQamChannelName | 1.3.6.1.4.1.1166.1.31.9.4.2.6.1.2 | DisplayString | read-only | The Name of this QAM Channel. |
| I32 apexRtspStatQamChannelNum | 1.3.6.1.4.1.1166.1.31.9.4.2.6.1.1 | Integer32 | not-accessible | The QAM Channel number. |
| apexRtspStatQamChannelTable | 1.3.6.1.4.1.1166.1.31.9.4.2.6 | not-accessible | Table of Status data for RTSP Session QAM Channels. | |
| apexRtspStatQamMptsModeEntry | 1.3.6.1.4.1.1166.1.31.9.4.2.7.1 | not-accessible | RTSP QAM MPTS Mode Configuration Table Entry. | |
| INT apexRtspStatQamMptsModeQamChannelMode | 1.3.6.1.4.1.1166.1.31.9.4.2.7.1.2 | INTEGER | read-only | The MPTS mode of this QAM Channel. The first session established on the QAM channel defines the MPTS mode. Each new session must have the same mode as long as one session is still active. |
| I32 apexRtspStatQamMptsModeQamChannelNum | 1.3.6.1.4.1.1166.1.31.9.4.2.7.1.1 | Integer32 | not-accessible | The QAM Channel number. |
| apexRtspStatQamMptsModeTable | 1.3.6.1.4.1.1166.1.31.9.4.2.7 | not-accessible | Table of MPTS Mode Status data for RTSP Session QAM Channels. | |
| apexRtspStatus | 1.3.6.1.4.1.1166.1.31.9.4.2 | |||
| apexRtspStatusGeneral | 1.3.6.1.4.1.1166.1.31.9.4.2.1 | |||
| INT apexSaveConfig | 1.3.6.1.4.1.1166.1.31.1.1.1.1 | INTEGER | read-write | Writing this object will commit the current configuration to Flash. While a read returns the value savingConfigToFlash, the flash is being saved; the save may not have been initiated by an SNMP set. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| apexSesContConfEntry | 1.3.6.1.4.1.1166.1.31.9.1.2.1 | not-accessible | Session Control Configuration Table Entry. | |
| ENA apexSesContConfFollowDtcp | 1.3.6.1.4.1.1166.1.31.9.1.1.7 | EnableDisableTYPE | read-write | Determines how the copy protection settings (CCI, APS, and CIT) within the PRK will be set. All outputs in Session Control (SDV) mode will use this setting for following input DTCP. Disabled - Use ERM Configuration settings if encryption blob provided. Use CTE settings when in CTE encryption mode and no ERM encryption blob provided. Enabled - Follow input DTCP Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| I32 apexSesContConfGbePrimaryInterface | 1.3.6.1.4.1.1166.1.31.9.1.2.1.2 | Integer32 | read-write | The primary Gbe interface for Session Control. Zero indicates not available. This parameter cannot be changed for any output stream if there is at least 1 active session control mapping. Not configurable for RTSP. |
| I32 apexSesContConfGbeSecondaryInterface | 1.3.6.1.4.1.1166.1.31.9.1.2.1.3 | Integer32 | read-write | The secondary Gbe interface for RPC SDV. Zero indicates not available. This parameter cannot be changed for any output stream if there is at least 1 active session control mapping. Secondary selection is restricted based on Primary as follows: - Primary 1 or 2: Secondary must be 1 or 2 - Primary 3 or 4: Secondary must be 3 or 4 Not configurable for RTSP. |
| ENA apexSesContConfInputPreEncryptCheck | 1.3.6.1.4.1.1166.1.31.9.1.1.5 | EnableDisableTYPE | read-write | Session Control Pre-Encryption Checking. Indicates if the APEX is to check if the input service is pre-encrypted or clear. Pre-encrypted is determined by examining the input PMT for a CA ECM descriptor (any CA ECM descriptor). If pre-encrypted, setting this flag will cause the APEX to pass through ECM PID for this service. For input services that have a GI CA ECM descriptor, the APEX will also pass through the PIT message (extract and re-insert the PIT). The output PMT for pre-encrypted services will contain a CA ECM descriptor (referencing the ECM PID). When PID Remapping is enabled, pre-encryption for a service is only valid when the input ECM PID is on a different PID than the associated PMT PID. If this flag is set to pre-encryption and the input service is not pre-encrypted, then the setting of this flag has no affect on the output service. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| I32 apexSesContConfOutputTsNum | 1.3.6.1.4.1.1166.1.31.9.1.2.1.1 | Integer32 | not-accessible | Output transport stream number (index). |
| INT apexSesContConfProtocol | 1.3.6.1.4.1.1166.1.31.9.1.1.1 | INTEGER | read-write | The communication protocol for output streams in Session Control operating mode. This determines the type of protocol the APEX will use to communicate with an Edge Resource Manager/Switch Digital Video Manager. This parameter cannot be changed when there are any active Session Control mappings. All Session Control mappings must be removed prior to changing this protocol. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| RAT apexSesContConfRateCompareType | 1.3.6.1.4.1.1166.1.31.9.1.1.3 | RateComparisonTYPE | read-write | This is the rate to use for comparing input streams. It is either Information rate or Stream rate. This applies to monitoring for Bit Rate alarming and monitoring of Redundant Pairs. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| I32 apexSesContConfRedundThreshold | 1.3.6.1.4.1.1166.1.31.9.1.1.4 | Integer32 | read-write | This object is obsolete. Session Control Redundancy Threshold. This is the percent used to determine Fail Over from Primary to Secondary, and Switch Back from Secondary to Primary. If a value of zero is specified, Fail Over or Switch Back will not occur. Range is 0 to 100%. Primary Fail Over to Secondary: FailOver = (PrimaryRate) = (Threshold * SecondaryRate) The Primary must remain at or above the threshold for apexGbeConfInRedundMonitorPeriod seconds. The APEX will delay Switch Back an additional apexGbeConfInRedundSwitchTime seconds. Switch Back will not occur when apexGbeConfInRedundAutoSwitchBack is 'disabled'. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| INT apexSesContConfRedundType | 1.3.6.1.4.1.1166.1.31.9.1.1.6 | INTEGER | read-write | The redundancy type for output streams in Session Control operating mode. - hotWarm indicates only 1 input stream, primary or secondary, is open at any one time. For multicast streams, primary will be joined initially. The secondary is joined after a failover (the primary will be dropped prior to joining the secondary). - hotHot indicates both the primary and secondary streams are opened at the same time. For multicast streams, both streams are joined immediately. Changes to the redundancy type cannot be made while there are active routes or sessions. All routes and sessions must be deleted prior to changing the redundancy type. Once written, a save must be performed via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') |
| apexSesContConfTable | 1.3.6.1.4.1.1166.1.31.9.1.2 | not-accessible | This is a table of Session Control configuration parameters for each output transport stream. This table defines the primary and secondary Gigabit Ethernet interfaces for each output stream in Session Control operating mode. The primary and secondary interfaces cannot be changed for an output stream when there are active Session Control mappings. All Session Control mappings on an output stream must be removed prior to changing the primary or secondary interface settings. Once written, the change to this table will only take immediate effect after apexSesContConfTableApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexSesContConfTableApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini') | |
| APP apexSesContConfTableApplyChange | 1.3.6.1.4.1.1166.1.31.9.1.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the apexSesContConfTable. This parameter MUST be set to 'apply' in order for any of the data in the apexSesContConfTable to take effect. This parameter MUST be set LAST after all other data in the apexSesContConfTable has been configured. @Config(config=no, reboot=no) |
| INT apexSesContStatProtocol | 1.3.6.1.4.1.1166.1.31.9.2.1.1 | INTEGER | read-only | The communication protocol in use for output streams in Session Control operating mode. |
| apexSessionControl | 1.3.6.1.4.1.1166.1.31.9 | |||
| apexSessionControlConfig | 1.3.6.1.4.1.1166.1.31.9.1 | |||
| apexSessionControlConfigGeneral | 1.3.6.1.4.1.1166.1.31.9.1.1 | |||
| apexSessionControlStatus | 1.3.6.1.4.1.1166.1.31.9.2 | |||
| apexSessionControlStatusGeneral | 1.3.6.1.4.1.1166.1.31.9.2.1 | |||
| ENA apexSimulcryptEmEnable | 1.3.6.1.4.1.1166.1.31.20.1.1.3 | EnableDisableTYPE | read-write | Simulcrypt EM Enable. If set to 'enabled' the EM will display the Simulcrypt specific screens. User will be allowed to view Simulcrypt status and perform configuration changes via the EM. This parameter only enables and disables the ability to use the EM Simulcrypt screens. It does not enable or disable Simulcrypt as there is a specific Simulcrypt mode per output stream. Once written, the change to this parameter will only take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexSimulcryptExternalEisSetting | 1.3.6.1.4.1.1166.1.31.20.1.1.2 | INTEGER | read-write | Default simulcrypt External EIS encryption setting. This determines if services are sent out in the clear or are encrypted when Simulcrypt mode is set to External EIS and the services have not yet been provisioned. This allows a user to have services scrambled but unviewable prior to services being provisioned (to prevent services from being viewable). This parameter is only applicable for output streams that are in Simulcrypt External EIS mode. When this setting is changed, it only affects new service mappings. Services that are already mapped will not be modified. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| IP apexSntpServerIpAddr | 1.3.6.1.4.1.1166.1.31.2.1.1.4 | IpAddress | read-write | This contains the IP address of the specified SNTP server. If apexTimeSource is SNTP and apexSntpServerSpecified is set to specified, then the apex will poll for time from this IP address. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| INT apexSntpServerSpecified | 1.3.6.1.4.1.1166.1.31.2.1.1.3 | INTEGER | read-write | When the TimeSource is SNTP, this object specifies whether the APEX will only accept time for a single SNTP server or from any server that broadcasts time. When notSpecified, the APEX will accept time from any SNTP server. When specified, the APEX will poll for time from the address of the SNTP server specified by the SntpServerIP address object. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| I32 apexSntpUtcOffset | 1.3.6.1.4.1.1166.1.31.2.1.1.2 | Integer32 | read-write | The value of this object is the Universal Time Coordinated (UTC) offset from GPS time. Subtract this from GPS time to convert from GPS to UTC. Units are seconds. When time source is SNTP, this object can be set to specify the UTC offset that the APEX will use in calculating GPS time. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| ENA apexSupportPreencryptedSimulcrypt | 1.3.6.1.4.1.1166.1.31.26.1.1.1 | EnableDisableTYPE | read-write | Allows to configure the APEX to support services pre-encrypted with Simulcrypt. All the CA descriptors present in the input PMT will be copied to the output PMT, modifying the ECM PID references if needed. Default value is enabled. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexSys | 1.3.6.1.4.1.1166.1.31.1 | |||
| apexSysConfig | 1.3.6.1.4.1.1166.1.31.1.1 | |||
| apexSysConfigGeneral | 1.3.6.1.4.1.1166.1.31.1.1.1 | |||
| apexSysConfigMcEmmInsertion | 1.3.6.1.4.1.1166.1.31.1.1.2 | |||
| apexSysStatus | 1.3.6.1.4.1.1166.1.31.1.2 | |||
| apexSysStatusGeneral | 1.3.6.1.4.1.1166.1.31.1.2.1 | |||
| apexSysStatusVersions | 1.3.6.1.4.1.1166.1.31.1.2.2 | |||
| I32 apexSystemTime | 1.3.6.1.4.1.1166.1.31.2.2.1.1 | Integer32 | read-only | The value of this object is the current System Time of the APEX. The system time is reported in GPS seconds. To determine the APEXs system time in UTC the apexSntpUtcOffset object must also be read and used in the calculation. |
| apexTemperature | 1.3.6.1.4.1.1166.1.31.3 | |||
| apexTemperatureConfig | 1.3.6.1.4.1.1166.1.31.3.1 | |||
| apexTemperatureConfigGeneral | 1.3.6.1.4.1.1166.1.31.3.1.1 | |||
| apexTemperatureStatus | 1.3.6.1.4.1.1166.1.31.3.2 | |||
| apexTemperatureStatusGeneral | 1.3.6.1.4.1.1166.1.31.3.2.1 | |||
| apexTime | 1.3.6.1.4.1.1166.1.31.2 | |||
| apexTimeConfig | 1.3.6.1.4.1.1166.1.31.2.1 | |||
| apexTimeConfigGeneral | 1.3.6.1.4.1.1166.1.31.2.1.1 | |||
| INT apexTimeSource | 1.3.6.1.4.1.1166.1.31.2.1.1.1 | INTEGER | read-write | The source for system time. The time source can be configured to come from an SNTP time source, or be generated internally. When configured as internal: - The APEX will internally keep time starting at GPS time 0. A user can set the time to a valid GPS time in this mode. - The system time and UTC offset in internal mode are not updated and therefore are not valid. When configured to receive time via SNTP the SntpServerSpecified object and SntpServiceIP objects can be used to optionally define the SNTP server. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini') |
| apexTimeStatus | 1.3.6.1.4.1.1166.1.31.2.2 | |||
| apexTimeStatusGeneral | 1.3.6.1.4.1.1166.1.31.2.2.1 | |||
| apexTraps | 1.3.6.1.4.1.1166.1.31.0 | |||
| APP apexUdpMapApplyChange | 1.3.6.1.4.1.1166.1.31.18.1.2.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the row of data in the Udp Map Table. A row in this table corresponds to the same row index in the Udp Map table. This parameter MUST be set to 'apply' in order for any of the data in the Udp Map Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the Udp Map Table row has been configured. @Config(config=no, reboot=no) |
| apexUdpMapApplyEntry | 1.3.6.1.4.1.1166.1.31.18.1.2.1 | not-accessible | UDP Map Apply Table Entry. | |
| I32 apexUdpMapApplyOutputTsNum | 1.3.6.1.4.1.1166.1.31.18.1.2.1.1 | Integer32 | not-accessible | The index of the Udp Map Apply Table. |
| apexUdpMapApplyTable | 1.3.6.1.4.1.1166.1.31.18.1.2 | not-accessible | Table of Apply Change for the data for UDP Map Table. A row in this table corresponds to the same row index in the UDP Map table. | |
| apexUdpMapConfig | 1.3.6.1.4.1.1166.1.31.18.1 | |||
| apexUdpMapConfigGeneral | 1.3.6.1.4.1.1166.1.31.18.1.1 | |||
| apexUdpMapEntry | 1.3.6.1.4.1.1166.1.31.18.1.3.1 | not-accessible | Udp Mapping Table Entry. | |
| ENA apexUdpMapFollowDtcp | 1.3.6.1.4.1.1166.1.31.18.1.1.4 | EnableDisableTYPE | read-write | Determines how the copy protection settings (CCI, APS, and CIT) within the PRK will be set. All outputs in UDP Port Mapping mode will use this setting for following input DTCP. Disabled - Use CTE configured settings if output in CTE encryption mode Enabled - Follow input DTCP Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') |
| I32 apexUdpMapInputInterface | 1.3.6.1.4.1.1166.1.31.18.1.3.1.2 | Integer32 | read-write | Input GBE port. Range: '1 - 4' = GBE port number |
| STR apexUdpMapInvalidApplyText | 1.3.6.1.4.1.1166.1.31.18.2.2.1.2 | DisplayString | read-only | When apexUdpMapApplyChange is set to applyNotInProgressInvalidData, this entry may contain a text description of what was wrong with the data. |
| I32 apexUdpMapModeBits | 1.3.6.1.4.1.1166.1.31.18.1.1.2 | Integer32 | read-write | Value that will be placed in the two MSBs of each the calculated UDP port number (bits 14 and 15). Once written, the change to this parameter will take immediate effect and all mappings will be removed. Mappings will not be re-added until apexUdpMapApplyChange is set to 'apply' for all transport streams. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') |
| APP apexUdpMapMulticastApplyChange | 1.3.6.1.4.1.1166.1.31.18.1.5.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for the row of data in the UDP Map Multicast Table. A row in this table corresponds to the same row index in the UDP Map Multicast Table. This parameter MUST be set to 'apply' in order for any of the data in the UDP Map Multicast Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the UDP Map Multicast Table row has been configured. @Config(config=no, reboot=no) |
| apexUdpMapMulticastApplyEntry | 1.3.6.1.4.1.1166.1.31.18.1.5.1 | not-accessible | UDP Map Multicast Apply Table Entry. | |
| I32 apexUdpMapMulticastApplyIndex | 1.3.6.1.4.1.1166.1.31.18.1.5.1.1 | Integer32 | not-accessible | The index of the UDP Map Multicast Table. |
| apexUdpMapMulticastApplyTable | 1.3.6.1.4.1.1166.1.31.18.1.5 | not-accessible | Table of Apply Change for the UDP Map Multicast Table. A row in this table corresponds to the same row index in the UDP Map Multicast Table (apexUdpMapMulticastTable). | |
| ENA apexUdpMapMulticastEnable | 1.3.6.1.4.1.1166.1.31.18.1.4.1.2 | EnableDisableTYPE | read-write | Indicates whether this UDP Map Multicast entry is enabled or disabled. |
| apexUdpMapMulticastEntry | 1.3.6.1.4.1.1166.1.31.18.1.4.1 | not-accessible | UDP Map Multicast Table Entry. | |
| I32 apexUdpMapMulticastIndex | 1.3.6.1.4.1.1166.1.31.18.1.4.1.1 | Integer32 | not-accessible | Index of UDP Map Multicast Stream Table. |
| I32 apexUdpMapMulticastInterface | 1.3.6.1.4.1.1166.1.31.18.1.4.1.3 | Integer32 | read-write | Number of the input interface (Port number). Range: '0' = Not Applicable GBE = 1-4 |
| STR apexUdpMapMulticastInvalidApplyText | 1.3.6.1.4.1.1166.1.31.18.2.1.1 | DisplayString | read-only | When apexUdpMapMulticastApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid. |
| IP apexUdpMapMulticastMcastIp | 1.3.6.1.4.1.1166.1.31.18.1.4.1.5 | IpAddress | read-write | The Multicast receive IP address. An IP address of 0.0.0.0 indicates singlecast only. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved. |
| IP apexUdpMapMulticastSourceIp | 1.3.6.1.4.1.1166.1.31.18.1.4.1.6 | IpAddress | read-write | This is the IP address of the source device. This field is only used when a multicast IP address is also specified. |
| apexUdpMapMulticastTable | 1.3.6.1.4.1.1166.1.31.18.1.4 | not-accessible | Table of data for UDP Map Multicast. Each entry in this table identifies a Gigabit Ethernet input stream that is used for multicast UDP Port Mapping. Once written, the change to this table will only take immediate effect after apexUdpMapMulticastApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexUdpMapMulticastApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') | |
| I32 apexUdpMapMulticastUdp | 1.3.6.1.4.1.1166.1.31.18.1.4.1.4 | Integer32 | read-write | GBE Input UDP Port. Range: 0-65535 |
| I32 apexUdpMapNumberProgs | 1.3.6.1.4.1.1166.1.31.18.1.3.1.4 | Integer32 | read-write | Indicates the number of programs that are to be mapped to the output transport stream. One UDP port is opened for each program mapped to the output transport stream. |
| I32 apexUdpMapOutputTsNum | 1.3.6.1.4.1.1166.1.31.18.1.3.1.1 | Integer32 | not-accessible | Index of Udp Mapping Table. |
| ENA apexUdpMapPreEncryptCheck | 1.3.6.1.4.1.1166.1.31.18.1.1.1 | EnableDisableTYPE | read-write | UDP Mapping pre-encryption checking. Indicates if the APEX is to check if input services are pre-encrypted or clear. Pre-encrypted is determined by examining the input PMT for a CA ECM descriptor (any CA ECM descriptor). If pre-encrypted, setting this flag will cause the APEX to pass through ECM PID for the service. For input services that have a GI CA ECM descriptor, the APEX will also pass through the PIT message (extract and re-insert the PIT). The output PMT for pre-encrypted services will contain a CA ECM descriptor (referencing the ECM PID). When PID Remapping is enabled, pre-encryption for a service is only valid when the input ECM PID is on a different PID than the associated PMT PID. If this flag is set to pre-encryption and the input service is not pre-encrypted, then the setting of this flag has no affect on the output service. Once written, the change to this parameter will take immediate effect and all mappings will be removed. Mappings will not be re-added until apexUdpMapApplyChange is set to 'apply' for all transport streams. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') |
| I32 apexUdpMapStartProgNum | 1.3.6.1.4.1.1166.1.31.18.1.3.1.3 | Integer32 | read-write | Indicates the first program number in a sequential range of programs that are to be routed to the same output transport stream. |
| apexUdpMapStatus | 1.3.6.1.4.1.1166.1.31.18.2 | |||
| apexUdpMapStatusEntry | 1.3.6.1.4.1.1166.1.31.18.2.2.1 | not-accessible | Udp Mapping Status Table Entry. | |
| apexUdpMapStatusGeneral | 1.3.6.1.4.1.1166.1.31.18.2.1 | |||
| I32 apexUdpMapStatusOutputTsNum | 1.3.6.1.4.1.1166.1.31.18.2.2.1.1 | Integer32 | not-accessible | Index of Udp Mapping Status Table. |
| apexUdpMapStatusTable | 1.3.6.1.4.1.1166.1.31.18.2.2 | not-accessible | Table of status data for Udp Mapping. There are 48 rows in this table. Each row corresponds to one QAM channel. | |
| apexUdpMapTable | 1.3.6.1.4.1.1166.1.31.18.1.3 | not-accessible | Table of data for Udp Mapping. There are 48 rows in this table. Each row corresponds to one QAM channel. Once written, the change to this table will only take immediate effect after apexUdpMapApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexUdpMapApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') | |
| I32 apexUdpMapTsOffset | 1.3.6.1.4.1.1166.1.31.18.1.1.3 | Integer32 | read-write | Used as part of the Standardized UDP Port calculation. Transport Stream index can be relative 0 or relative 1. Once written, the change to this parameter will take immediate effect and all mappings will be removed. Mappings will not be re-added until apexUdpMapApplyChange is set to 'apply' for all transport streams. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini') |
| apexUdpPortMapping | 1.3.6.1.4.1.1166.1.31.18 | |||
| U32 apexUserSuppliedTime | 1.3.6.1.4.1.1166.1.31.2.1.1.5 | Unsigned32 | read-write | The value of this object is the GPS Time the APEX is given via user entry. The time is reported in GPS seconds. This time is ONLY used when the APEX is set to Internal time mode. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no) |
| NTF trapCannotCreateSemaphore | 1.3.6.1.4.1.1166.1.31.0.24 | This trap is issued when a semaphore cannot be created. The trapAdditionalInfoInteger1 will contain the task and Function ID, the trapAdditionalInfoInteger2 and trapAdditionalInfoInteger3 will not be used. | ||
| NTF trapCannotOpenSocket | 1.3.6.1.4.1.1166.1.31.0.25 | This trap is issued when a socket cannot be opened. The trapAdditionalInfoInteger1 will contain the task and Function ID. The trapAdditionalInfoInteger2 will contain the errno returned by the call to socket(). The trapAdditionalInfoInteger3 is not used. | ||
| NTF trapChassisRedundancyAvailabilityFault | 1.3.6.1.4.1.1166.1.31.0.8092 | See corresponding alarm apexAlarmChassisRedundancyAvailabilityFault. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapChassisRedundancyConfigurationFault | 1.3.6.1.4.1.1166.1.31.0.8094 | See corresponding alarm apexAlarmChassisRedundancyConfigurationFault. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapChassisRedundancyFirmwareVersionMismatch | 1.3.6.1.4.1.1166.1.31.0.8112 | See corresponding event apexEventChassisRedunFirmwareVersionMismatch. Additional Info is not used. | ||
| NTF trapChassisRedundancyLinkFault | 1.3.6.1.4.1.1166.1.31.0.8093 | See corresponding alarm apexAlarmChassisRedundancyLinkFault. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapChassisRedundancyPrimaryFailover | 1.3.6.1.4.1.1166.1.31.0.8090 | See corresponding alarm apexAlarmChassisRedundancyPrimaryFailover. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapChassisRedundancyPrimaryForceFailover | 1.3.6.1.4.1.1166.1.31.0.8110 | See corresponding event apexEventChassisRedunPrimaryForceFailover. Additional Info is not used. | ||
| NTF trapChassisRedundancyQAMVersionMismatch | 1.3.6.1.4.1.1166.1.31.0.8113 | See corresponding event apexEventChassisRedunQAMVersionMismatch. Additional Info is not used. | ||
| NTF trapChassisRedundancySecondaryFailover | 1.3.6.1.4.1.1166.1.31.0.8091 | See corresponding alarm apexAlarmChassisRedundancySecondaryFailover. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapChassisRedundancySecondaryForceFailover | 1.3.6.1.4.1.1166.1.31.0.8111 | See corresponding event apexEventChassisRedunSecondaryForceFailover. Additional Info is not used. | ||
| NTF trapConditionAlreadyInList | 1.3.6.1.4.1.1166.1.31.0.21 | This trap is issued if a condition is being set and it is already in the condition list. trapAdditionalInfoInteger1 : Task and Function ID (task and function generates the error condition) trapAdditionalInfoInteger2 : Condition number trapAdditionalInfoInteger3 : Condition severity | ||
| NTF trapConditionListFull | 1.3.6.1.4.1.1166.1.31.0.22 | This trap is issued if a condition is being set and the condition list is full. trapAdditionalInfoInteger1 : Task and Function ID (task and function generates the error condition) trapAdditionalInfoInteger2 : Condition number trapAdditionalInfoInteger3 : Condition severity | ||
| NTF trapConditionNotInList | 1.3.6.1.4.1.1166.1.31.0.20 | This trap is issued if a condition is being cleared and it is not in the condition list. trapAdditionalInfoInteger1 : Task and Function ID (task and function generates the error condition) trapAdditionalInfoInteger2 : Condition number trapAdditionalInfoInteger3 : Condition severity | ||
| NTF trapConfigurationChangeDisplayString | 1.3.6.1.4.1.1166.1.31.0.4 | This trap is issued if configuration of a single variable with DisplayString type was changed (via ANY interface). TrapChangedValueDisplayString variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate' | ||
| NTF trapConfigurationChangeInteger | 1.3.6.1.4.1.1166.1.31.0.3 | This trap is issued if configuration of a single variable with integer type was changed (via ANY interface). TrapChangedValueInteger variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate' | ||
| NTF trapConfigurationChangeIpAddress | 1.3.6.1.4.1.1166.1.31.0.6 | This trap is issued if configuration of a single variable with IpAddress type was changed (via ANY interface). TrapChangedValueIpAddress variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate' | ||
| NTF trapConfigurationChangeOID | 1.3.6.1.4.1.1166.1.31.0.5 | This trap is issued if configuration of a single variable with OID type was changed (via ANY interface). TrapChangedValueOID variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate' | ||
| NTF trapDepiControlConnectionFault | 1.3.6.1.4.1.1166.1.31.0.8080 | See corresponding alarm apexAlarmDepiControlConnectionFault. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapDepiSessionSetupFault | 1.3.6.1.4.1.1166.1.31.0.8081 | See corresponding alarm apexAlarmDepiSessionSetupFault. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapDtiSyncLossFault | 1.3.6.1.4.1.1166.1.31.0.8082 | See corresponding alarm apexAlarmDtiSyncLossFault. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapEmUserLoginFailed | 1.3.6.1.4.1.1166.1.31.0.8100 | See corresponding event apexEventEmUserLoginFailed. Additional Info is not used. | ||
| NTF trapFanFault | 1.3.6.1.4.1.1166.1.31.0.8003 | See corresponding alarm apexAlarmFanFault. This trap is sent on summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGbeBufferFullness | 1.3.6.1.4.1.1166.1.31.0.8021 | See corresponding alarm apexAlarmGbeBufferFullness. Additional Info 1 carries the Gigabit Ethernet Processor Number (1 to 2). Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGbeInputStreamHighBitRate | 1.3.6.1.4.1.1166.1.31.0.8023 | See corresponding alarm apexAlarmGbeInputStreamHighBitRate. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGbeInputStreamLowBitRate | 1.3.6.1.4.1.1166.1.31.0.8022 | See corresponding alarm apexAlarmGbeInputStreamLowBitRate. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGbeInterfaceRedundFailOver | 1.3.6.1.4.1.1166.1.31.0.8029 | See corresponding alarm apexAlarmGbeInterfaceRedundFailOver. This trap is sent on a GbE Redundant Pair basis. Additional Info 1 contains the GbE interface number that lost link. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGbeLossOfInputStream | 1.3.6.1.4.1.1166.1.31.0.8027 | See corresponding alarm apexAlarmGbeLossOfInputStream. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGbeLossOfPhysicalInput | 1.3.6.1.4.1.1166.1.31.0.8020 | See corresponding alarm apexAlarmGbeLossOfPhysicalInput. Additional Info 1 carries the Gigabit Ethernet Interface Number (1 to 4). Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGbeMptsRedundFailOver | 1.3.6.1.4.1.1166.1.31.0.8025 | See corresponding alarm apexAlarmGbeMptsRedundFailOver. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGbeMptsRedundPrimaryThreshold | 1.3.6.1.4.1.1166.1.31.0.8024 | See corresponding alarm apexAlarmGbeMptsRedundPrimaryThreshold. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapGigeToHostCommFault | 1.3.6.1.4.1.1166.1.31.0.8028 | See corresponding alarm apexAlarmGigeToHostCommFault. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapHardwareFault | 1.3.6.1.4.1.1166.1.31.0.8000 | See corresponding alarm apexAlarmHardwareFault. Additional Info 1 carries HW Error Code (refer to HW Event Log for details). Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapInvalidCaseInSwitch | 1.3.6.1.4.1.1166.1.31.0.23 | This trap is issued when in a switch statement the default case is reached. The trapAdditionalInfoInteger1 will contain the task and Function ID. The trapAdditionalInfoInteger2 will contain value of the switch. The trapAdditionalInfoInteger3 is not used. | ||
| NTF trapInvalidInitData | 1.3.6.1.4.1.1166.1.31.0.8001 | See corresponding alarm apexAlarmInvalidInitData. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapInvalidMessageReceived | 1.3.6.1.4.1.1166.1.31.0.27 | This trap is issued when an invalid message is received. The trapAdditionalInfoInteger1 will contain the task and Function ID. The trapAdditionalInfoInteger2 will contain the message ID and the trapAdditionalInfoInteger3 is not used. | ||
| NTF trapOutputOverflow | 1.3.6.1.4.1.1166.1.31.0.8041 | See corresponding alarm apexAlarmOutputOverflow. This trap is sent on an Output Transport Stream basis. Additional Info 1 carries the Output Transport Stream number (1 to 48). Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapOutputUtilizationFault | 1.3.6.1.4.1.1166.1.31.0.8040 | See corresponding alarm apexAlarmOutputUtilizationFault. This trap is sent on an Output Transport Stream basis. Additional Info 1 carries the Output Transport Stream number (1 to 48). Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapPowerFault | 1.3.6.1.4.1.1166.1.31.0.8004 | See corresponding alarm apexAlarmPowerFault. Additional Info 1 carries the apexPsStatusTable index (1 to 2). Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapQamChannelFault | 1.3.6.1.4.1.1166.1.31.0.8044 | See corresponding alarm apexAlarmQamChannelFault. This trap is sent on a QAM Channel basis. Additional Info 1 carries the QAM Channel number. 1 to 8 = QAM Module 1, RF 1, QAM Channel A to H 9 to 16 = QAM Module 1, RF 2, QAM Channel A to H 17 to 24 = QAM Module 2, RF 1, QAM Channel A to H 25 to 32 = QAM Module 2, RF 2, QAM Channel A to H 33 to 40 = QAM Module 3, RF 1, QAM Channel A to H 41 to 48 = QAM Module 3, RF 2, QAM Channel A to H Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapQamModuleFault | 1.3.6.1.4.1.1166.1.31.0.8042 | See corresponding alarm apexAlarmQamModuleFault. This trap is sent on a QAM Module basis. Additional Info 1 carries the QAM Module number (1 to 3). Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapQamModuleUpgraded | 1.3.6.1.4.1.1166.1.31.0.8101 | See corresponding event apexEventQamModuleUpgraded. Additional Info is not used. | ||
| NTF trapQamRfPortFault | 1.3.6.1.4.1.1166.1.31.0.8043 | See corresponding alarm apexAlarmQamRfPortFault. This trap is sent on a QAM RF Port basis. Additional Info 1 carries the QAM RF Port number: RF Port 1 = QAM Module 1, RF 1 RF Port 2 = QAM Module 1, RF 2 RF Port 3 = QAM Module 2, RF 1 RF Port 4 = QAM Module 2, RF 2 RF Port 5 = QAM Module 3, RF 1 RF Port 6 = QAM Module 3, RF 2 Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapQamRfRedundFailOver | 1.3.6.1.4.1.1166.1.31.0.8045 | See corresponding alarm apexAlarmQamRfRedundFailOver. This trap is sent on a Primary QAM RF Port basis. Additional Info 1 carries the Primary QAM RF Port number. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapQamRfRedundMismatch | 1.3.6.1.4.1.1166.1.31.0.8046 | See corresponding alarm apexAlarmQamRfRedundMismatch. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapRdsCommFault | 1.3.6.1.4.1.1166.1.31.0.8060 | See corresponding alarm apexAlarmRdsCommFault. Additional Info is not used. | ||
| NTF trapRemCommFault | 1.3.6.1.4.1.1166.1.31.0.8070 | See corresponding alarm apexAlarmRemCommFault. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapRemFault | 1.3.6.1.4.1.1166.1.31.0.8071 | See corresponding alarm apexAlarmRemFault. This trap is sent on a summary basis. Additional Info is not used. | ||
| NTF trapRtspControllerCommFault | 1.3.6.1.4.1.1166.1.31.0.8050 | See corresponding alarm apexAlarmRtspControllerCommFault. This trap is sent on a controller basis. Additional Info 1 carries the controller number. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapServiceInError | 1.3.6.1.4.1.1166.1.31.0.8026 | See corresponding alarm apexAlarmServiceInError. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapTemperatureFault | 1.3.6.1.4.1.1166.1.31.0.8002 | See corresponding alarm apexAlarmTemperatureFault. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used. | ||
| NTF trapUnknownMessageReceived | 1.3.6.1.4.1.1166.1.31.0.26 | This trap is issued when an unknown message is received. The trapAdditionalInfoInteger1 will contain the task and Function ID. The trapAdditionalInfoInteger2 will contain the message ID and the trapAdditionalInfoInteger3 is not used. |
RFC description
Monitors and configures Motorola APEX digital transport adapter system status and QAM modules.
Start monitoring BigBand Networks APEX video/broadband gateway (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.