All MIBs › APEX-MIB › apexGbeConfIfRedundEnable
apexGbeConfIfRedundEnable
Module: APEX-MIB
OID (symbolic): APEX-MIB::apexGbeConfIfRedundEnable
OID (numeric): 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.2
Node type: OBJECT-TYPE
Type: EnableDisableTYPE
Access: read-write
Description: Enables GbE Interface Redundancy for ports pair. Failover is based on link status. If the primary GbE fails, the secondary GbE will become active and will start receiving content. There is no data rate comparison, as only one interface in the redundancy pair is active. The secondary GbE cannot be in use prior to enabling redundancy. TS redundancy may not be used at the same time as interface redundancy. Interface redundancy is not applicable when chassis redundancy is enabled.
Once written, the change to this table will only take immediate effect after apexGbeConfIfRedundApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig.
@Config(config=yes, reboot=no) @Commit(param=apexGbeConfIfRedundApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
What is apexGbeConfIfRedundEnable?
Enables link-based redundancy for a GbE interface pair, so that if the primary interface loses its link the secondary interface automatically takes over and begins receiving content. Only one interface in the pair is active at a time.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.2 snmpwalk -v2c -c public <target> APEX-MIB::apexGbeConfIfRedundEnable
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.2.1 snmpget -v2c -c public <target> APEX-MIB::apexGbeConfIfRedundEnable.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.2.1 s <value>
Start monitoring BigBand Networks APEX video/broadband gateway (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the APEX-MIB::apexGbeConfIfRedundEnable OID value, configure state conditions and alerts, and monitor any BigBand Networks APEX video/broadband gateway (legacy) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.1166 | gi | BCS-IDENT-MIB |
| 1.3.6.1.4.1.1166.1 | giproducts | BCS-IDENT-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.1166.1.31 | apex | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.7 | apexGbe | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.7.1 | apexGbeConfig | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.7.1.7 | apexGbeConfigInterfaceRedundancy | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.7.1.7.2 | apexGbeConfigInterfaceRedundancyTable | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.7.1.7.2.1 | apexGbeConfigInterfaceRedundancyEntry | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.2 | apexGbeConfIfRedundEnable | APEX-MIB |