All MIBs › APEX-MIB › apexEnableDtiSyncLossFault
apexEnableDtiSyncLossFault
Module: APEX-MIB
OID (symbolic): APEX-MIB::apexEnableDtiSyncLossFault
OID (numeric): 1.3.6.1.4.1.1166.1.31.102.1.8082
Node type: OBJECT-TYPE
Type: EnableDisableTYPE
Access: read-write
Description: This setting enables or disables apexAlarmDtiSyncLossFault. When set to 'enabled' the alarm will operate as described.
When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared.
Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
@Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
What is apexEnableDtiSyncLossFault?
Controls whether the DTI (DOCSIS Timing Interface) synchronization loss fault alarm is active. When enabled, the alarm is raised and rolled into the unit alarm status if DTI sync is lost; when disabled, sync-loss events are suppressed and the alarm condition stays 'ok'.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.1166.1.31.102.1.8082 snmpwalk -v2c -c public <target> APEX-MIB::apexEnableDtiSyncLossFault
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.1166.1.31.102.1.8082.1 snmpget -v2c -c public <target> APEX-MIB::apexEnableDtiSyncLossFault.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.1166.1.31.102.1.8082.1 s <value>
Start monitoring BigBand Networks APEX video/broadband gateway (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the APEX-MIB::apexEnableDtiSyncLossFault OID value, configure state conditions and alerts, and monitor any BigBand Networks APEX video/broadband gateway (legacy) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.1166 | gi | BCS-IDENT-MIB |
| 1.3.6.1.4.1.1166.1 | giproducts | BCS-IDENT-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.1166.1.31 | apex | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.102 | apexConfigAlarms | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.102.1 | apexConfAlarmEnable | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.102.1.8082 | apexEnableDtiSyncLossFault | APEX-MIB |