All MIBs › APEX-MIB › apexEnableGbeMptsRedundFailOver
apexEnableGbeMptsRedundFailOver
Module: APEX-MIB
OID (symbolic): APEX-MIB::apexEnableGbeMptsRedundFailOver
OID (numeric): 1.3.6.1.4.1.1166.1.31.102.1.8025
Node type: OBJECT-TYPE
Type: EnableDisableTYPE
Access: read-write
Description: This setting enables or disables apexAlarmGbeMptsRedundFailOver.
When set to 'enabled' the alarm will operate as described.
When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared.
Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
@Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
What is apexEnableGbeMptsRedundFailOver?
Enables or disables alerting when the GbE MPTS redundancy system has performed an automatic failover from the primary to a backup transport stream. When enabled, operators are notified whenever the device switches away from the primary input due to a detected fault.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.1166.1.31.102.1.8025 snmpwalk -v2c -c public <target> APEX-MIB::apexEnableGbeMptsRedundFailOver
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.1166.1.31.102.1.8025.1 snmpget -v2c -c public <target> APEX-MIB::apexEnableGbeMptsRedundFailOver.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.1166.1.31.102.1.8025.1 s <value>
Start monitoring BigBand Networks APEX video/broadband gateway (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the APEX-MIB::apexEnableGbeMptsRedundFailOver OID value, configure state conditions and alerts, and monitor any BigBand Networks APEX video/broadband gateway (legacy) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.1166 | gi | BCS-IDENT-MIB |
| 1.3.6.1.4.1.1166.1 | giproducts | BCS-IDENT-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.1166.1.31 | apex | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.102 | apexConfigAlarms | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.102.1 | apexConfAlarmEnable | APEX-MIB |
| 1.3.6.1.4.1.1166.1.31.102.1.8025 | apexEnableGbeMptsRedundFailOver | APEX-MIB |