CPS-MIB

All MIBs › CPS-MIB

Category: Hardware and Environment

Description: Monitors CyberPower Systems UPS devices including input/output power, battery status, and load percentage.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CPS-MIB?

CPS-MIB is a private MIB (enterprise OID 3808) for a UPS product, defining trap-notification configuration alongside standard UPS identification objects. Its objects cover a trap-accepter table (address, community string, severity, active flag) with a count, DHCP-enable flag, device IP address, clock date/time, generic trap-info fields (integer, IP address, string, gauge, time-ticks, event-ID) for building custom traps, restart/reset control actions, and standard UPS identification (model, name, firmware revision, manufacture date, serial number). As a configuration/notification MIB it lets an administrator confirm which management stations receive traps and at what minimum severity. It is deployed on this vendor's UPS product line. Engineers can download the CPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

UPS product line (enterprise OID 3808)

Monitoring Examples

An administrator checks mconfigTrapAccepterTable to confirm the correct management station and minimum severity are configured to receive UPS alert traps.

What Can Be Monitored

trap-destination configuration and UPS identification

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Gauge
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT accepterActive	1.3.6.1.4.1.3808.2.1.2.1.5	INTEGER	read-write	A receiver will accept traps if yes, and none if no.
IP accepterAddr	1.3.6.1.4.1.3808.2.1.2.1.2	IpAddress	read-write	The trap receiver IP address.
INT acceptThisDevice	1.3.6.1.4.1.3808.1.1.1.5.1.2.1.4	INTEGER	read-write	An equipment is plugged if yes, unplugged if no.
NTF adminLoginInfo	1.3.6.1.4.1.3808.0.65			INFORMATION: Administrator login.
NTF adminLogoutInfo	1.3.6.1.4.1.3808.0.66			INFORMATION: Administrator logout.
ats	1.3.6.1.4.1.3808.1.1.5
NTF atsCancelPendingCommand	1.3.6.1.4.1.3808.0.337			INFORMATIONAL: A cancel pending command has been made on ATS. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number (0 indicates all outlets). The fourth argument is the outlet name (or device name if all outlets).
NTF atsCommunicationEstablished	1.3.6.1.4.1.3808.0.315			INFORMATIONAL: ATS communication has been established. The first argument is the device name. The second argument is the serial number.
NTF atsCommunicationLost	1.3.6.1.4.1.3808.0.314			MAJOR: ATS communication lost. The first argument is the device name. The second argument is the serial number.
atsConfig	1.3.6.1.4.1.3808.1.1.5.3
INT atsConfigDevLCDOffTime	1.3.6.1.4.1.3808.1.1.5.3.9	INTEGER	read-write	The amount of time (in seconds) which LCD turn off automatically after it remains idle for.
INT atsConfigFrequencyDeviation	1.3.6.1.4.1.3808.1.1.5.3.8	INTEGER	read-write	To configure the frequency deviation.
INT atsConfigMediumRangeValue	1.3.6.1.4.1.3808.1.1.5.3.6	INTEGER	read-write	To configure the Medium Range value of acceptable voltage from a power source.
INT atsConfigNarrowRangeValue	1.3.6.1.4.1.3808.1.1.5.3.5	INTEGER	read-write	To configure the Narrow Range value of acceptable voltage from a power source.
INT atsConfigNominalVoltage	1.3.6.1.4.1.3808.1.1.5.3.2	INTEGER	read-write	This variable returns the nominal voltage of the input.
INT atsConfigPreferredSource	1.3.6.1.4.1.3808.1.1.5.3.1	INTEGER	read-write	This variable returns the preferred source of power when both sources are OK.
INT atsConfigTransferVoltageRange	1.3.6.1.4.1.3808.1.1.5.3.4	INTEGER	read-write	This variable defines the range of acceptable voltage from a power source. If the voltage measured from the selected input source is not within this range, the Automatic Transfer Switch will switch over (transfer) to the alternate power source.
INT atsConfigVoltageSensitivity	1.3.6.1.4.1.3808.1.1.5.3.3	INTEGER	read-write	This variable defines the sensitivity to changes in voltage: high(1) for best protection, low(3) for frequent small line voltage changes.
INT atsConfigWideRangeValue	1.3.6.1.4.1.3808.1.1.5.3.7	INTEGER	read-write	To configure the Wide Range value of acceptable voltage from a power source.
atsControl	1.3.6.1.4.1.3808.1.1.5.4
INT atsCtrlClearEventCounts	1.3.6.1.4.1.3808.1.1.5.4.2	INTEGER	read-write	Setting this variable will clear all event counts in Automatic Transfer Switch. Returns (-1) if unsupported.
INT atsCtrlResetATS	1.3.6.1.4.1.3808.1.1.5.4.1	INTEGER	read-write	Setting this variable will cause the Automatic Transfer Switch to reboot or reset relative setting to default value.
NTF atsDB9CommunicationLost	1.3.6.1.4.1.3808.0.318			WARNING: DB9 communication lost. The first argument is the device name. The second argument is the serial number.
NTF atsDB9CommunicationLostCleared	1.3.6.1.4.1.3808.0.319			INFORMATIONAL: DB9 communication lost has been cleared. The first argument is the device name. The second argument is the serial number.
NTF atsDevHardwareFault	1.3.6.1.4.1.3808.0.322			CRITICAL: Device hardware failure. The first argument is the device name. The second argument is the serial number.
NTF atsDevHardwareFaultCleared	1.3.6.1.4.1.3808.0.323			INFORMATIONAL: Device hardware failure has been cleared. The first argument is the device name. The second argument is the serial number.
NTF atsDeviceConfigChanged	1.3.6.1.4.1.3808.0.325			INFORMATIONAL: A device configuration change has been made. The first argument is the device name. The second argument is the serial number.
NTF atsEventCountsCleared	1.3.6.1.4.1.3808.0.327			INFORMATIONAL: Event counts has been cleared. The first argument is the device name. The second argument is the serial number.
atsIdent	1.3.6.1.4.1.3808.1.1.5.1
STR atsIdentAgentFirmwareRevision	1.3.6.1.4.1.3808.1.1.5.1.12	DisplayString	read-only	A string identifying the Agent firmware revision.
STR atsIdentAgentHardwareRevision	1.3.6.1.4.1.3808.1.1.5.1.11	DisplayString	read-only	The hardware revision of the Agent.
STR atsIdentAgentModelName	1.3.6.1.4.1.3808.1.1.5.1.10	DisplayString	read-only	A string identifying the model name of the Agent.
STR atsIdentAgentSerialNumber	1.3.6.1.4.1.3808.1.1.5.1.13	DisplayString	read-only	A string identifying the serial number of the Agent.
STR atsIdentDateOfManufacture	1.3.6.1.4.1.3808.1.1.5.1.6	DisplayString	read-only	The date when the Automatic Transfer Switch was manufactured in mm/dd/yyyy format. This value is set at the factory.
INT atsIdentDeviceOutletNum	1.3.6.1.4.1.3808.1.1.5.1.9	INTEGER	read-only	This gives the outlet number of the device
INT atsIdentDeviceRatingCurrent	1.3.6.1.4.1.3808.1.1.5.1.8	INTEGER	read-only	This gives the device rating current in Amps
STR atsIdentDeviceRatingVoltage	1.3.6.1.4.1.3808.1.1.5.1.7	DisplayString	read-only	A string identifing the Automatic Transfer Switch rating voltage.
STR atsIdentFirmwareRev	1.3.6.1.4.1.3808.1.1.5.1.4	DisplayString	read-only	A string identifying the Automatic Transfer Switch firmware revision.
STR atsIdentHardwareRev	1.3.6.1.4.1.3808.1.1.5.1.3	DisplayString	read-only	The hardware revision of the Automatic Transfer Switch. This value is set at the factory.
STR atsIdentModelName	1.3.6.1.4.1.3808.1.1.5.1.2	DisplayString	read-only	A string identifying the model name of the Automatic Transfer Switch. This value is set at the factory.
STR atsIdentName	1.3.6.1.4.1.3808.1.1.5.1.1	DisplayString	read-write	The name of the ATS. The maximum string size is device dependent.
STR atsIdentSerialNumber	1.3.6.1.4.1.3808.1.1.5.1.5	DisplayString	read-only	A string identifying the serial number of the Automatic Transfer Switch. This value is set at the factory.
NTF atsInputHighFrequency	1.3.6.1.4.1.3808.0.310			WARNING: The upper frequency limit has been crossed. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the input frequency.
NTF atsInputHighFrequencyCleared	1.3.6.1.4.1.3808.0.311			INFORMATIONAL: The upper frequency condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the input frequency.
NTF atsInputHighVoltage	1.3.6.1.4.1.3808.0.306			WARNING: The upper voltage limit has been crossed. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the phase voltage.
NTF atsInputHighVoltageCleared	1.3.6.1.4.1.3808.0.307			INFORMATIONAL: The upper voltage condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the phase voltage.
NTF atsInputLowFrequency	1.3.6.1.4.1.3808.0.312			WARNING: The lower frequency limit has been crossed. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the input frequency.
NTF atsInputLowFrequencyCleared	1.3.6.1.4.1.3808.0.313			INFORMATIONAL: The lower frequency condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the input frequency.
NTF atsInputLowVoltage	1.3.6.1.4.1.3808.0.308			WARNING: The lower voltage limit has been crossed. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the phase voltage.
NTF atsInputLowVoltageCleared	1.3.6.1.4.1.3808.0.309			INFORMATIONAL: The lower voltage condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the phase voltage.
NTF atsLCDCommunicationLost	1.3.6.1.4.1.3808.0.316			WARNING: LCD communication lost. The first argument is the device name. The second argument is the serial number.
NTF atsLCDCommunicationLostCleared	1.3.6.1.4.1.3808.0.317			INFORMATIONAL: LCD communication lost has been cleared. The first argument is the device name. The second argument is the serial number.
atsLoad	1.3.6.1.4.1.3808.1.1.5.5
atsLoadCfgBankEntry	1.3.6.1.4.1.3808.1.1.5.5.3.4.1		not-accessible	The ATS phase to configure.
INT atsLoadCfgBankLowLoad	1.3.6.1.4.1.3808.1.1.5.5.3.4.1.2	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in Amps. A warning will be issued when the load is less than the threshold value. A threshold value of 0 Amps effectively disables this warning.
INT atsLoadCfgBankNearOverLoad	1.3.6.1.4.1.3808.1.1.5.5.3.4.1.3	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value.
INT atsLoadCfgBankOutletRestriction	1.3.6.1.4.1.3808.1.1.5.5.3.4.1.5	INTEGER	read-write	This OID controls the behavior of a ATS phase when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding phase to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigOverloadThreshold OID is exceeded.
INT atsLoadCfgBankOverLoad	1.3.6.1.4.1.3808.1.1.5.5.3.4.1.4	INTEGER	read-write	A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value.
atsLoadCfgBankTable	1.3.6.1.4.1.3808.1.1.5.5.3.4		not-accessible	Allows for configuration of each ATS bank.
INT atsLoadCfgBankTableIndex	1.3.6.1.4.1.3808.1.1.5.5.3.4.1.1	INTEGER	read-only	The index to the ATS bank entry.
INT atsLoadCfgBankTableSize	1.3.6.1.4.1.3808.1.1.5.5.3.3	INTEGER	read-only	The size of the Bank Table.
INT atsLoadCfgPhase	1.3.6.1.4.1.3808.1.1.5.5.3.2.1.2	INTEGER	read-only	For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), phase3 (3), phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
atsLoadCfgPhaseEntry	1.3.6.1.4.1.3808.1.1.5.5.3.2.1		not-accessible	The ATS phase to configure.
INT atsLoadCfgPhaseLowLoad	1.3.6.1.4.1.3808.1.1.5.5.3.2.1.3	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in Amps. A warning will be issued when the load is less than the threshold value. A threshold value of 0 Amps effectively disables this warning.
INT atsLoadCfgPhaseNearOverLoad	1.3.6.1.4.1.3808.1.1.5.5.3.2.1.4	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value.
INT atsLoadCfgPhaseOutletRestriction	1.3.6.1.4.1.3808.1.1.5.5.3.2.1.6	INTEGER	read-write	This OID controls the behavior of a ATS phase when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding phase to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigOverloadThreshold OID is exceeded.
INT atsLoadCfgPhaseOverLoad	1.3.6.1.4.1.3808.1.1.5.5.3.2.1.5	INTEGER	read-write	A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value.
atsLoadCfgPhaseTable	1.3.6.1.4.1.3808.1.1.5.5.3.2		not-accessible	Allows for configuration of each ATS phase.
INT atsLoadCfgPhaseTableIndex	1.3.6.1.4.1.3808.1.1.5.5.3.2.1.1	INTEGER	read-only	The index to the ATS phase entry.
INT atsLoadCfgPhaseTableSize	1.3.6.1.4.1.3808.1.1.5.5.3.1	INTEGER	read-only	The size of the Phase Table.
atsLoadConfig	1.3.6.1.4.1.3808.1.1.5.5.3
atsLoadDevBankEntry	1.3.6.1.4.1.3808.1.1.5.5.1.4.1		not-accessible	The ATS Banks Access.
INT atsLoadDevBankMaxLoad	1.3.6.1.4.1.3808.1.1.5.5.1.4.1.2	INTEGER	read-only	Getting this OID will return the maximum rated power that each bank of the ATS can provide. It is represented in Amps.
atsLoadDevBankTable	1.3.6.1.4.1.3808.1.1.5.5.1.4		not-accessible	Allows for getting the Bank Max Load in the ATS.
INT atsLoadDevBankTableIndex	1.3.6.1.4.1.3808.1.1.5.5.1.4.1.1	INTEGER	read-only	The index to the ATS bank entry.
INT atsLoadDevBankTableSize	1.3.6.1.4.1.3808.1.1.5.5.1.3	INTEGER	read-only	The size of the Bank Table.
atsLoadDevice	1.3.6.1.4.1.3808.1.1.5.5.1
INT atsLoadDevPhase	1.3.6.1.4.1.3808.1.1.5.5.1.2.1.2	INTEGER	read-only	For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), phase3 (3), phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
atsLoadDevPhaseEntry	1.3.6.1.4.1.3808.1.1.5.5.1.2.1		not-accessible	The ATS Phases Access.
INT atsLoadDevPhaseMaxLoad	1.3.6.1.4.1.3808.1.1.5.5.1.2.1.3	INTEGER	read-only	Getting this OID will return the maximum rated power that each phase of the ATS can provide. It is represented in Amps.
atsLoadDevPhaseTable	1.3.6.1.4.1.3808.1.1.5.5.1.2		not-accessible	Allows for getting the Phase Max Load in the ATS.
INT atsLoadDevPhaseTableIndex	1.3.6.1.4.1.3808.1.1.5.5.1.2.1.1	INTEGER	read-only	The index to ATS phase entry.
INT atsLoadDevPhaseTableSize	1.3.6.1.4.1.3808.1.1.5.5.1.1	INTEGER	read-only	The size of the Phase Table.
atsLoadStatus	1.3.6.1.4.1.3808.1.1.5.5.2
INT atsLoadStatusBankEnergy	1.3.6.1.4.1.3808.1.1.5.5.2.4.1.6	INTEGER	read-only	Getting this OID will return the phase/bank apparent power measured in 0.1 kilowatt-hours.
atsLoadStatusBankEntry	1.3.6.1.4.1.3808.1.1.5.5.2.4.1		not-accessible	The ATS Bank Access.
INT atsLoadStatusBankLoad	1.3.6.1.4.1.3808.1.1.5.5.2.4.1.3	INTEGER	read-only	The output current in 0.1 amperes drawn by the load on the ATS
INT atsLoadStatusBankLoadState	1.3.6.1.4.1.3808.1.1.5.5.2.4.1.4	INTEGER	read-only	Getting this OID will return the bank load state.
INT atsLoadStatusBankPhase	1.3.6.1.4.1.3808.1.1.5.5.2.4.1.2	INTEGER	read-only	Getting this OID will return the phase number.
INT atsLoadStatusBankPower	1.3.6.1.4.1.3808.1.1.5.5.2.4.1.5	INTEGER	read-only	The output power in Watts.
INT atsLoadStatusBankStartTime	1.3.6.1.4.1.3808.1.1.5.5.2.4.1.7	INTEGER	read-only	Getting this OID will return the date and time of the last energy meter reset
atsLoadStatusBankTable	1.3.6.1.4.1.3808.1.1.5.5.2.4		not-accessible	Allows for getting the Bank Load status in the ATS.
INT atsLoadStatusBankTableIndex	1.3.6.1.4.1.3808.1.1.5.5.2.4.1.1	INTEGER	read-only	The index to ATS bank entry.
INT atsLoadStatusBankTableSize	1.3.6.1.4.1.3808.1.1.5.5.2.3	INTEGER	read-only	The size of the Bank Table.
INT atsLoadStatusPhase	1.3.6.1.4.1.3808.1.1.5.5.2.2.1.2	INTEGER	read-only	For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), phase3 (3), phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
atsLoadStatusPhaseEntry	1.3.6.1.4.1.3808.1.1.5.5.2.2.1		not-accessible	The ATS Phases Access.
INT atsLoadStatusPhaseLoad	1.3.6.1.4.1.3808.1.1.5.5.2.2.1.3	INTEGER	read-only	The output current in 0.1 amperes drawn by the load on the ATS
INT atsLoadStatusPhaseLoadState	1.3.6.1.4.1.3808.1.1.5.5.2.2.1.4	INTEGER	read-only	Getting this OID will return the phase load state.
INT atsLoadStatusPhasePower	1.3.6.1.4.1.3808.1.1.5.5.2.2.1.5	INTEGER	read-only	The output power in Watts.
atsLoadStatusPhaseTable	1.3.6.1.4.1.3808.1.1.5.5.2.2		not-accessible	Allows for getting the Phase Load status in the ATS.
INT atsLoadStatusPhaseTableIndex	1.3.6.1.4.1.3808.1.1.5.5.2.2.1.1	INTEGER	read-only	The index to ATS phase entry.
INT atsLoadStatusPhaseTableSize	1.3.6.1.4.1.3808.1.1.5.5.2.1	INTEGER	read-only	The size of the Phase Table.
NTF atsLowLoad	1.3.6.1.4.1.3808.0.332			WARNING: The load has been lower than low load threshold. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
NTF atsLowLoadCleared	1.3.6.1.4.1.3808.0.333			INFORMATIONAL: The low load condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
NTF atsNearOverload	1.3.6.1.4.1.3808.0.330			WARNING: The load has exceeded near overload threshold. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
NTF atsNearOverloadCleared	1.3.6.1.4.1.3808.0.331			INFORMATIONAL: The near overload condition has beed cleared. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
atsOutlet	1.3.6.1.4.1.3808.1.1.5.6
atsOutletCfgEntry	1.3.6.1.4.1.3808.1.1.5.6.7.1		not-accessible	The outlet to configure.
STR atsOutletCfgOutletName	1.3.6.1.4.1.3808.1.1.5.6.7.1.2	DisplayString	read-write	The name of the outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size.
INT atsOutletCfgPowerOffTime	1.3.6.1.4.1.3808.1.1.5.6.7.1.4	INTEGER	read-write	The amount of time (in seconds) the outlet will delay powering off when a command that requires a turn-off delay is issued. Allowed values are: -1 - never power off. 0 - power off immediately. 1 to 7200 - power off up to 7200 seconds after being commanded.
INT atsOutletCfgPowerOnTime	1.3.6.1.4.1.3808.1.1.5.6.7.1.3	INTEGER	read-write	The amount of time (in seconds) the outlet will delay powering on at coldstart or when a command that requires a turn-on delay is issued. Allowed values are: -1 - never power on. 0 - power on immediately. 1 to 7200 - power on up to 7200 seconds after being commanded.
INT atsOutletCfgRebootDuration	1.3.6.1.4.1.3808.1.1.5.6.7.1.5	INTEGER	read-write	During a reboot sequence, power is turned off and then back on. This OID defines the amount of time to wait, in seconds, after turning the power off, at the start of the sequence, before turning power back on, at the end of the reboot sequence. Allowed range is any value between 5 and 60 seconds (1 minute).
atsOutletCfgTable	1.3.6.1.4.1.3808.1.1.5.6.7		not-accessible	Allows for configuration of individual outlets.
INT atsOutletCfgTableIndex	1.3.6.1.4.1.3808.1.1.5.6.7.1.1	INTEGER	read-only	The index to the outlet entry.
INT atsOutletCfgTableSize	1.3.6.1.4.1.3808.1.1.5.6.6	INTEGER	read-only	The size of the outlet config table.
NTF atsOutletConfigChanged	1.3.6.1.4.1.3808.0.326			INFORMATIONAL: A outlet configuration change has been made. The first argument is the device name. The second argument is the serial number.
INT atsOutletCtrlCommand	1.3.6.1.4.1.3808.1.1.5.6.5.1.3	INTEGER	read-write	Getting this variable will return the outlet state. If the outlet is on, the immediateOn (2) value will be returned. If the outlet is off, the immediateOff (2) value will be returned. Setting this variable to immediateOn (2) will immediately turn the outlet on. Setting this variable to immediateOff (3) will immediately turn the outlet off. Setting this variable to immediateReboot (4) will immediately reboot the outlet. Setting this variable to delayedOn (5) will turn the outlet on after the ePDUOutletConfigPowerOnTime OID time has elapsed. Setting this variable to delayedOff (6) will turn the outlet off after the ePDUOutletConfigPowerOffTime OID time has elapsed. Setting this variable to delayedReboot (7) will cause the ATS to perform a delayedOff command, wait the atsOutletCfgRebootDuration OID time, and then perform a delayedOn command. Setting this variable to cancelPendingCommand (8) will cause any pending command to this outlet to be canceled.
atsOutletCtrlEntry	1.3.6.1.4.1.3808.1.1.5.6.5.1		not-accessible	The outlet to control.
STR atsOutletCtrlOutletName	1.3.6.1.4.1.3808.1.1.5.6.5.1.2	DisplayString	read-only	The name of the outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size. This OID is provided for informational purposes only.
atsOutletCtrlTable	1.3.6.1.4.1.3808.1.1.5.6.5		not-accessible	Allows for control of the individual outlets.
INT atsOutletCtrlTableIndex	1.3.6.1.4.1.3808.1.1.5.6.5.1.1	INTEGER	read-only	The index to the outlet entry.
INT atsOutletCtrlTableSize	1.3.6.1.4.1.3808.1.1.5.6.4	INTEGER	read-only	The size of the outlet control table.
INT atsOutletDevColdStartDelay	1.3.6.1.4.1.3808.1.1.5.6.1.3	INTEGER	read-write	The amount of delay, in seconds, between when power is provided to the ATS and when the ATS provides basic master power to the outlets. Allowed values are: -1 - never apply power automatically. 0 - apply power immediately. 1 to 300 - delay up to 300 seconds (5 minutes).
INT atsOutletDevColdStartState	1.3.6.1.4.1.3808.1.1.5.6.1.4	INTEGER	read-write	The ATS outlet state after coldstart. Allowed values are: 1 - all outlets on after coldstart. 2 - outlet status same as previous state.
INT atsOutletDevCommand	1.3.6.1.4.1.3808.1.1.5.6.1.6	INTEGER	read-write	Setting this OID to immediateAllOn (2) will turn all outlets on immediately. Setting this OID to immediateAllOff (3) will turn all outlets off immediately. Setting this OID to immediateAllReboot (4) will reboot all outlets immediately. Setting this OID to delayedAllOn (5) will turn all outlets on as defined by each outlet's atsOutletCfgPowerOnTime OID value. Setting this OID to delayedAllOff (6) will turn all outlets off as defined by each outlet's atsOutletCfgPowerOffTime OID value. Setting this OID to delayedAllReboot (7) will cause a delayedAllOff command to be performed. Once all outlets are off, the Switched Rack ATS will then delay the largest atsOutletCfgRebootDuration OID time, and then perform a delayedAllOn command. Setting this OID to cancelAllPendingCommands (8) will cause all pending commands on the Switched Rack ATS to be canceled. Getting this OID will return the noCommandAll (1) value.
INT atsOutletDevCtrlOutletNum	1.3.6.1.4.1.3808.1.1.5.6.1.2	INTEGER	read-only	The number of controlled outlets on the ATS.
atsOutletDevice	1.3.6.1.4.1.3808.1.1.5.6.1
INT atsOutletDevLocalCtrl	1.3.6.1.4.1.3808.1.1.5.6.1.5	INTEGER	read-write	To configure enable or disable outlet local control function.
INT atsOutletDevTotalOutletNum	1.3.6.1.4.1.3808.1.1.5.6.1.1	INTEGER	read-only	The total number of outlets on the ATS.
NTF atsOutletOff	1.3.6.1.4.1.3808.0.339			INFORMATIONAL: An outlet on ATS has turned off. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF atsOutletOffCommand	1.3.6.1.4.1.3808.0.335			INFORMATIONAL: An outlet on ATS has been assigned to turn off. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF atsOutletOn	1.3.6.1.4.1.3808.0.338			INFORMATIONAL: An outlet on ATS has turned on. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF atsOutletOnCommand	1.3.6.1.4.1.3808.0.334			INFORMATIONAL: An outlet on ATS has been assigned to turn on. The first argument is the device name. The second argument is the serial number. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF atsOutletRebootCommand	1.3.6.1.4.1.3808.0.336			INFORMATIONAL: An outlet on ATS has been assigned to reboot. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
atsOutletStatusEntry	1.3.6.1.4.1.3808.1.1.5.6.3.1		not-accessible	The outlet to gather status from.
INT atsOutletStatusOutletBank	1.3.6.1.4.1.3808.1.1.5.6.3.1.6	INTEGER	read-only	The bank associated with this outlet.
INT atsOutletStatusOutletCmdPending	1.3.6.1.4.1.3808.1.1.5.6.3.1.4	INTEGER	read-only	Getting this variable will return the command pending state of the outlet. If a command is pending on the outlet, the outletStatusCommandPending (1) value will be returned. If there is not a command pending on the outlet, the outletStatusNoCommandPending (2) will be returned.
STR atsOutletStatusOutletName	1.3.6.1.4.1.3808.1.1.5.6.3.1.2	DisplayString	read-only	The name of the outlet. The maximum string size is device dependent. This OID is provided for informational purposes only.
INT atsOutletStatusOutletPhase	1.3.6.1.4.1.3808.1.1.5.6.3.1.5	INTEGER	read-only	The phase/s associated with this outlet. For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), or phase3 (3) for outlets tied to a single phase. For outlets tied to two phases, this object will return phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
INT atsOutletStatusOutletState	1.3.6.1.4.1.3808.1.1.5.6.3.1.3	INTEGER	read-only	Getting this variable will return the outlet state. If the outlet is on, the outletStatusOn (1) value will be returned. If the outlet is off, the outletStatusOff (2) value will be returned.
atsOutletStatusTable	1.3.6.1.4.1.3808.1.1.5.6.3		not-accessible	Allows for getting of status of individual outlets.
INT atsOutletStatusTableIndex	1.3.6.1.4.1.3808.1.1.5.6.3.1.1	INTEGER	read-only	The index to the outlet entry.
INT atsOutletStatusTableSize	1.3.6.1.4.1.3808.1.1.5.6.2	INTEGER	read-only	The size of the outlet status table.
NTF atsOverload	1.3.6.1.4.1.3808.0.328			WARNING: The load has exceeded overload threshold. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
NTF atsOverloadCleared	1.3.6.1.4.1.3808.0.329			INFORMATIONAL: The overload condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
NTF atsPowerSupplyFault	1.3.6.1.4.1.3808.0.320			CRITICAL: Power supply failure. The first argument is the device name. The second argument is the serial number. The third argument is the input source of the power supply.
NTF atsPowerSupplyFaultCleared	1.3.6.1.4.1.3808.0.321			CRITICAL: Power supply failure. The first argument is the device name. The second argument is the serial number. The third argument is the input source of the power supply.
NTF atsRedundancyFail	1.3.6.1.4.1.3808.0.304			WARNING: Redundancy fails. The first argument is the device name. The second argument is the serial number. The third argument is the source name.
NTF atsRedundancyRestored	1.3.6.1.4.1.3808.0.305			INFORMATIONAL: Redundancy has been restored. The first argument is the device name. The second argument is the serial number. The third argument is the source name.
NTF atsSourceConfigChanged	1.3.6.1.4.1.3808.0.324			INFORMATIONAL: A source configuration change has been made. The first argument is the device name. The second argument is the serial number.
NTF atsSourceFault	1.3.6.1.4.1.3808.0.302			WARNING: Source fault occurs. The first argument is the device name. The second argument is the serial number. The third argument is the source name.
NTF atsSourceFaultCleared	1.3.6.1.4.1.3808.0.303			INFORMATIONAL: Source fault has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name.
atsStatus	1.3.6.1.4.1.3808.1.1.5.2
INT atsStatusCommStatus	1.3.6.1.4.1.3808.1.1.5.2.1.1	INTEGER	read-only	This variable returns the current communication status between the Automatic Transfer Switch and the Agent.
INT atsStatusDevDB9CommStatus	1.3.6.1.4.1.3808.1.1.5.2.1.9	INTEGER	read-only	This variable returns the communication status of the DB9.
atsStatusDevice	1.3.6.1.4.1.3808.1.1.5.2.1
INT atsStatusDevInRelayStatus	1.3.6.1.4.1.3808.1.1.5.2.1.6	INTEGER	read-only	This variable returns the status of the input relay.
INT atsStatusDevLCDCommStatus	1.3.6.1.4.1.3808.1.1.5.2.1.8	INTEGER	read-only	This variable returns the communication status of the LCD.
INT atsStatusDevOutRelayStatus	1.3.6.1.4.1.3808.1.1.5.2.1.7	INTEGER	read-only	This variable returns the status of the Output relay.
INT atsStatusDevSourceRelayStatus	1.3.6.1.4.1.3808.1.1.5.2.1.5	INTEGER	read-only	This variable returns the status of the source relay.
atsStatusInput	1.3.6.1.4.1.3808.1.1.5.2.2
atsStatusInputEntry	1.3.6.1.4.1.3808.1.1.5.2.2.2.1		not-accessible	An entry containing information applicable to a particular input.
INT atsStatusInputFreqState	1.3.6.1.4.1.3808.1.1.5.2.2.2.1.8	INTEGER	read-only	The input frequency status.
INT atsStatusInputFrequency	1.3.6.1.4.1.3808.1.1.5.2.2.2.1.6	INTEGER	read-only	The input frequency in 0.1 Hertz.
STR atsStatusInputName	1.3.6.1.4.1.3808.1.1.5.2.2.2.1.2	DisplayString	read-write	A name given to a particular input.
INT atsStatusInputNum	1.3.6.1.4.1.3808.1.1.5.2.2.1	INTEGER	read-only	The number of input feeds to this device. This variable indicates the number of rows in the status input table.
INT atsStatusInputPhaseCurrent	1.3.6.1.4.1.3808.1.1.5.2.2.3.1.4	INTEGER	read-only	The input current in amperes, or -1 if it's unsupported by this Source.
atsStatusInputPhaseEntry	1.3.6.1.4.1.3808.1.1.5.2.2.3.1		not-accessible	An entry containing information applicable to a particular input phase.
INT atsStatusInputPhaseIndex	1.3.6.1.4.1.3808.1.1.5.2.2.3.1.2	INTEGER	read-only	The input phase identifier.
INT atsStatusInputPhasePower	1.3.6.1.4.1.3808.1.1.5.2.2.3.1.5	INTEGER	read-only	The input power in Watts, or -1 if it's unsupported by this Source.
atsStatusInputPhaseTable	1.3.6.1.4.1.3808.1.1.5.2.2.3		not-accessible	A list of input table entries. The number of entries is given by the sum of the atsNumInputPhases.
INT atsStatusInputPhaseTableIndex	1.3.6.1.4.1.3808.1.1.5.2.2.3.1.1	INTEGER	read-only	The input identifier.
INT atsStatusInputPhaseVoltage	1.3.6.1.4.1.3808.1.1.5.2.2.3.1.3	INTEGER	read-only	The input voltage in VAC, or -1 if it's unsupported by this Source.
atsStatusInputTable	1.3.6.1.4.1.3808.1.1.5.2.2.2		not-accessible	A list of input table entries. The number of entries is given by the value of atsNumInputs.
INT atsStatusInputTableIndex	1.3.6.1.4.1.3808.1.1.5.2.2.2.1.1	INTEGER	read-only	The input identifier.
INT atsStatusInputVolState	1.3.6.1.4.1.3808.1.1.5.2.2.2.1.7	INTEGER	read-only	The input voltage status.
INT atsStatusInputVoltage	1.3.6.1.4.1.3808.1.1.5.2.2.2.1.5	INTEGER	read-only	The input voltage in 0.1 Volt.
INT atsStatusInputVoltageOrientation	1.3.6.1.4.1.3808.1.1.5.2.2.2.1.4	INTEGER	read-only	The input voltage orientation: 1: unknown for this Source 2: singlePhase - phase 1 voltage is between Phase 1 and Neutral. 3: splitPhase - phase 1 voltage is between Phase 1 and Neutral; phase 2 voltage is between Phase 2 and Neutral; phase 3 voltage is between Phase 1 and Phase 2. 4: threePhasePhaseToNeutral - phase 1 voltage is between Phase 1 and Neutral; phase 2 voltage is between Phase 2 and Neutral; phase 3 voltage is between Phase 3 and Neutral. 5: threePhasePhaseToPhase - phase 1 voltage is between Phase 1 and Phase 2; phase 2 voltage is between Phase 2 and Phase 3; phase 3 voltage is between Phase 3 and Phase 1.
INT atsStatusNumInputPhase	1.3.6.1.4.1.3808.1.1.5.2.2.2.1.3	INTEGER	read-only	The number of input phases utilized in this device. The sum of all the atsStatusNumInputPhase variable indicates the number of rows in the status input phase table.
INT atsStatusPhaseSyncStatus	1.3.6.1.4.1.3808.1.1.5.2.1.4	INTEGER	read-only	This variable returns the status of the phase sync.
INT atsStatusPowerSupply12VStatus	1.3.6.1.4.1.3808.1.1.5.2.1.10.1.3	INTEGER	read-only	This variable returns the status of the power supply A 12V in system.
INT atsStatusPowerSupply3p3VStatus	1.3.6.1.4.1.3808.1.1.5.2.1.10.1.5	INTEGER	read-only	This variable returns the status of the power supply A 3.3V in system.
INT atsStatusPowerSupply5VStatus	1.3.6.1.4.1.3808.1.1.5.2.1.10.1.4	INTEGER	read-only	This variable returns the status of the power supply A 5V in system.
atsStatusPowerSupplyEntry	1.3.6.1.4.1.3808.1.1.5.2.1.10.1		not-accessible	An entry containing power supply information applicable to a particular input.
INT atsStatusPowerSupplyInputSource	1.3.6.1.4.1.3808.1.1.5.2.1.10.1.2	INTEGER	read-only	The input source to the power supply.
atsStatusPowerSupplyTable	1.3.6.1.4.1.3808.1.1.5.2.1.10		not-accessible	A list of power supply table entries.
INT atsStatusPowerSupplyTableIndex	1.3.6.1.4.1.3808.1.1.5.2.1.10.1.1	INTEGER	read-only	The input identifier.
INT atsStatusRedundancyState	1.3.6.1.4.1.3808.1.1.5.2.1.3	INTEGER	read-only	This variable returns the current redundancy state of the ATS. atsRedundancyLost(1) indicates that the ATS is unable to switch over to the alternate power source if the current source fails. atsFullyRedundant(2) indicates that the ATS will switch over to the alternate power source if the current source fails.
INT atsStatusSelectedSource	1.3.6.1.4.1.3808.1.1.5.2.1.2	INTEGER	read-only	This variable returns the current source of power.
NTF atsSwitchSource	1.3.6.1.4.1.3808.0.301			INFORMATIONAL: ATS has switched source. The first argument is the device name. The second argument is the serial number. The third argument is the selected source.
battmgr	1.3.6.1.4.1.3808.1.1.7
bmConfig	1.3.6.1.4.1.3808.1.1.7.3
INT bmConfigBattAH	1.3.6.1.4.1.3808.1.1.7.3.1	INTEGER	read-write	Battery manager battery AH type configuration, unit in 0.1 AH.
INT bmConfigHighResAlarmThreshold	1.3.6.1.4.1.3808.1.1.7.3.10	INTEGER	read-write	Battery high resistance alarm threshold, unit in 0.01 mOhm.
INT bmConfigHighResWarnThreshold	1.3.6.1.4.1.3808.1.1.7.3.12	INTEGER	read-write	Battery high resistance warning threshold, unit in 0.01 mOhm.
INT bmConfigHighTempAlarmThreshold	1.3.6.1.4.1.3808.1.1.7.3.8	INTEGER	read-write	Battery high temperature alarm threshold, unit in 0.1 degree C.
INT bmConfigHighVoltAlarmThreshold	1.3.6.1.4.1.3808.1.1.7.3.5	INTEGER	read-write	Battery high voltage alarm threshold setting, unit in 0.1 volt.
INT bmConfigHighVoltAlarmThreshold10mV	1.3.6.1.4.1.3808.1.1.7.3.16	INTEGER	read-write	Battery high voltage alarm threshold setting, unit in 10 mV (0.01 volt).
INT bmConfigLowResAlarmThreshold	1.3.6.1.4.1.3808.1.1.7.3.9	INTEGER	read-write	Battery low resistance alarm threshold, unit in 0.01 mOhm.
INT bmConfigLowResWarnThreshold	1.3.6.1.4.1.3808.1.1.7.3.11	INTEGER	read-write	Battery low resistance warning threshold, unit in 0.01 mOhm.
INT bmConfigLowTempAlarmThreshold	1.3.6.1.4.1.3808.1.1.7.3.7	INTEGER	read-write	Battery low temperature alarm threshold, unit in 0.1 degree C.
INT bmConfigLowVoltAlarmThreshold	1.3.6.1.4.1.3808.1.1.7.3.4	INTEGER	read-write	Battery low voltage alarm threshold setting, unit in 0.1 volt.
INT bmConfigLowVoltAlarmThreshold10mV	1.3.6.1.4.1.3808.1.1.7.3.15	INTEGER	read-write	Battery low voltage alarm threshold setting, unit in 10 mV (0.01 volt).
INT bmConfigMergeFeature	1.3.6.1.4.1.3808.1.1.7.3.17	INTEGER	read-write	String merge feature setting.
INT bmConfigProbesCountOnString	1.3.6.1.4.1.3808.1.1.7.3.3	INTEGER	read-write	Battery manager probe count on a string setting.
INT bmConfigResHealthAlarmThreshold	1.3.6.1.4.1.3808.1.1.7.3.13	INTEGER	read-write	Battery resistance health alarm threshold, unit in percentage and should larger than 100.
INT bmConfigResHealthWarnThreshold	1.3.6.1.4.1.3808.1.1.7.3.14	INTEGER	read-write	Battery resistance health warn threshold, unit in percentage and should larger than 100.
INT bmConfigStringCount	1.3.6.1.4.1.3808.1.1.7.3.2	INTEGER	read-write	Battery manager string count setting.
INT bmConfigVoltDiffAlarmThreshold	1.3.6.1.4.1.3808.1.1.7.3.6	INTEGER	read-write	Batteries within a string voltage difference threshold, unit in 0.1 volt.
bmControl	1.3.6.1.4.1.3808.1.1.7.4
INT bmControlProbeIndicator	1.3.6.1.4.1.3808.1.1.7.4.2	INTEGER	read-write	Battery manager will perform a probe indicator test when the variable is set to testIndicators(2). Get this oid will get noTestIndicators(1).
INT bmControlSysytemIdenticator	1.3.6.1.4.1.3808.1.1.7.4.1	INTEGER	read-write	Battery manager will perform a panel indicator test when the variable is set to testIndicators(2). Get this oid will get noTestIndicators(1).
bmFuncEqual	1.3.6.1.4.1.3808.1.1.7.7
INT bmFuncEqualActiveCond	1.3.6.1.4.1.3808.1.1.7.7.2	INTEGER	read-write	Volatge equalization will active when the voltage difference larger than this value, unit in 10mV.
TIK bmFuncEqualElapseTime	1.3.6.1.4.1.3808.1.1.7.7.5	TimeTicks	read-only	This oid shows the elapsed time since last equalization started.
INT bmFuncEqualEnable	1.3.6.1.4.1.3808.1.1.7.7.1	INTEGER	read-write	Battery voltage equalization configuration.
STR bmFuncEqualStartTime	1.3.6.1.4.1.3808.1.1.7.7.4	DisplayString	read-only	This oid shows the last equalization start time.
INT bmFuncEqualStatus	1.3.6.1.4.1.3808.1.1.7.7.3	INTEGER	read-only	This oid shows the current equalization status.
bmFuncRes	1.3.6.1.4.1.3808.1.1.7.6
bmFuncResMeasure	1.3.6.1.4.1.3808.1.1.7.6.1
INT bmFuncResMeasureInterval	1.3.6.1.4.1.3808.1.1.7.6.1.1	INTEGER	read-write	The time interval for battery manager to exercising resistance measurement, unit in hour(s).
STR bmFuncResMeasureLastUpdate	1.3.6.1.4.1.3808.1.1.7.6.1.4	DisplayString	read-only	When resistance measurement complete either by auto or manual, this oid will update to the last update time.
INT bmFuncResMeasureManualCmd	1.3.6.1.4.1.3808.1.1.7.6.1.2	INTEGER	read-write	This oid allows user to manual resistance measurement. Set this oid to measureResNow(2) to measure resistance immediately. Get bmFuncResMeasureLastCmdResult oid to check command acceptance.
INT bmFuncResMeasureManualResult	1.3.6.1.4.1.3808.1.1.7.6.1.3	INTEGER	read-only	Get this oid to confirm the last manual command result.
bmIdent	1.3.6.1.4.1.3808.1.1.7.1
STR bmIdentDateOfManufacture	1.3.6.1.4.1.3808.1.1.7.1.6	DisplayString	read-only	Battery manager manufacture date.
STR bmIdentFirmwareRev	1.3.6.1.4.1.3808.1.1.7.1.3	DisplayString	read-only	Battery manager firmware version.
STR bmIdentHardwareRev	1.3.6.1.4.1.3808.1.1.7.1.2	DisplayString	read-only	Battery manager hardware version.
STR bmIdentLCDFirmwareRev	1.3.6.1.4.1.3808.1.1.7.1.5	DisplayString	read-only	Battery manager LCD firmware version.
STR bmIdentLCDHardwareRev	1.3.6.1.4.1.3808.1.1.7.1.4	DisplayString	read-only	Battery manager LCD hardware version.
STR bmIdentLocation	1.3.6.1.4.1.3808.1.1.7.1.9	DisplayString	read-write	Battery manager system location.
STR bmIdentModelName	1.3.6.1.4.1.3808.1.1.7.1.1	DisplayString	read-only	Battery manager model name.
STR bmIdentName	1.3.6.1.4.1.3808.1.1.7.1.8	DisplayString	read-write	Battery manager system identification name.
STR bmIdentSerialNumber	1.3.6.1.4.1.3808.1.1.7.1.7	DisplayString	read-only	Battery manager serial number.
bmProbes	1.3.6.1.4.1.3808.1.1.7.5
NTF bmProbesAlarm	1.3.6.1.4.1.3808.0.603			ALARM: Probe alarm event. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the string index the probe located. The fifth argument is the battery index the probe located. The sixth argument is the alarm event specific identifier. The seventh argument is the trap information string.
INT bmProbesBattIndex	1.3.6.1.4.1.3808.1.1.7.5.3.1.4	INTEGER	read-only	The battery number the probe installed.
bmProbesEntry	1.3.6.1.4.1.3808.1.1.7.5.3.1		not-accessible	The status of probes installation to gather status from.
INT bmProbesIndex	1.3.6.1.4.1.3808.1.1.7.5.3.1.1	INTEGER	read-only	Probes table index
NTF bmProbesInfo	1.3.6.1.4.1.3808.0.605			INFO: Probe information. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the string index the probe located. The fifth argument is the battery index the probe located. The sixth argument is the alarm event specific identifier. The seventh argument is the trap information string.
INT bmProbesNum	1.3.6.1.4.1.3808.1.1.7.5.1	INTEGER	read-only	Current connected probe number.
INT bmProbesPackIndex	1.3.6.1.4.1.3808.1.1.7.5.3.1.2	INTEGER	read-only	The battery pack number the probe installed.
INT bmProbesResAlarmStatus	1.3.6.1.4.1.3808.1.1.7.5.9.1.6	INTEGER	read-only	The alarm status of the battery resistance.
INT bmProbesResBattIndex	1.3.6.1.4.1.3808.1.1.7.5.9.1.4	INTEGER	read-only	The index to the battery.
bmProbesResEntry	1.3.6.1.4.1.3808.1.1.7.5.9.1		not-accessible	The resistance status entry.
INT bmProbesResHealth	1.3.6.1.4.1.3808.1.1.7.5.9.1.8	INTEGER	read-only	The resistance health status, unit in percentage.
INT bmProbesResIndex	1.3.6.1.4.1.3808.1.1.7.5.9.1.1	INTEGER	read-only	The index of the resistance entry.
INT bmProbesResistance	1.3.6.1.4.1.3808.1.1.7.5.9.1.7	INTEGER	read-only	The resistance of the battery, unit in 0.01 mOhm.
INT bmProbesResPackIndex	1.3.6.1.4.1.3808.1.1.7.5.9.1.2	INTEGER	read-only	The battery pack index to the resistance entry.
INT bmProbesResProbeIndex	1.3.6.1.4.1.3808.1.1.7.5.9.1.5	INTEGER	read-only	The index to the probe.
INT bmProbesResStringIndex	1.3.6.1.4.1.3808.1.1.7.5.9.1.3	INTEGER	read-only	The index to the string.
bmProbesResTable	1.3.6.1.4.1.3808.1.1.7.5.9		not-accessible	Allows for getting of resistance of probes.
INT bmProbesResTableSize	1.3.6.1.4.1.3808.1.1.7.5.8	INTEGER	read-only	The size of the Resistance table
INT bmProbesStringIndex	1.3.6.1.4.1.3808.1.1.7.5.3.1.3	INTEGER	read-only	The string number the probe installed.
bmProbesTable	1.3.6.1.4.1.3808.1.1.7.5.3		not-accessible	Allows for getting of status of probes.
INT bmProbesTableSize	1.3.6.1.4.1.3808.1.1.7.5.2	INTEGER	read-only	Current configured probe number.
INT bmProbesTempAlarmStatus	1.3.6.1.4.1.3808.1.1.7.5.7.1.6	INTEGER	read-only	The alarm status of the temperature.
INT bmProbesTempBattIndex	1.3.6.1.4.1.3808.1.1.7.5.7.1.4	INTEGER	read-only	The index to the battery.
bmProbesTempEntry	1.3.6.1.4.1.3808.1.1.7.5.7.1		not-accessible	Temperature status entry.
INT bmProbesTemperature	1.3.6.1.4.1.3808.1.1.7.5.7.1.7	INTEGER	read-only	The temperature record, measure in 0.1 degree C.
INT bmProbesTempIndex	1.3.6.1.4.1.3808.1.1.7.5.7.1.1	INTEGER	read-only	The index of the temperature entry.
INT bmProbesTempPackIndex	1.3.6.1.4.1.3808.1.1.7.5.7.1.2	INTEGER	read-only	The battery pack index of the temperature entry.
INT bmProbesTempProbeIndex	1.3.6.1.4.1.3808.1.1.7.5.7.1.5	INTEGER	read-only	The index to the probe.
INT bmProbesTempStringIndex	1.3.6.1.4.1.3808.1.1.7.5.7.1.3	INTEGER	read-only	The index to the string.
bmProbesTempTable	1.3.6.1.4.1.3808.1.1.7.5.7		not-accessible	Allows for getting of temperature of probes.
INT bmProbesTempTableSize	1.3.6.1.4.1.3808.1.1.7.5.6	INTEGER	read-only	The size of the Temperature table
INT bmProbesVoltage	1.3.6.1.4.1.3808.1.1.7.5.5.1.7	INTEGER	read-only	Getting this oid to get battery voltage, unit in 10mV (0.01 volt).
INT bmProbesVoltageAlarmStatus	1.3.6.1.4.1.3808.1.1.7.5.5.1.6	INTEGER	read-only	The battery voltage alarm status.
INT bmProbesVoltageBattIndex	1.3.6.1.4.1.3808.1.1.7.5.5.1.4	INTEGER	read-only	The battery index to the voltage record within its string.
bmProbesVoltageEntry	1.3.6.1.4.1.3808.1.1.7.5.5.1		not-accessible	Batteries voltage status.
INT bmProbesVoltageEqualPercentage	1.3.6.1.4.1.3808.1.1.7.5.5.1.8	INTEGER	read-only	Getting this oid to get battery voltage equalizing power, unit in percentage.
INT bmProbesVoltageIndex	1.3.6.1.4.1.3808.1.1.7.5.5.1.1	INTEGER	read-only	The index of the voltage status entry.
INT bmProbesVoltagePackIndex	1.3.6.1.4.1.3808.1.1.7.5.5.1.2	INTEGER	read-only	The battery pack index to the voltage record.
INT bmProbesVoltageProbeIndex	1.3.6.1.4.1.3808.1.1.7.5.5.1.5	INTEGER	read-only	The probe index to the voltage record.
INT bmProbesVoltageStringIndex	1.3.6.1.4.1.3808.1.1.7.5.5.1.3	INTEGER	read-only	The battery string index to the voltage record.
bmProbesVoltageTable	1.3.6.1.4.1.3808.1.1.7.5.5		not-accessible	Allows for getting of voltage of batteries.
INT bmProbesVoltageTableSize	1.3.6.1.4.1.3808.1.1.7.5.4	INTEGER	read-only	The size of the battery voltage table
bmProperty	1.3.6.1.4.1.3808.1.1.7.2
STR bmPropertyInputVoltageRange	1.3.6.1.4.1.3808.1.1.7.2.3	DisplayString	read-only	Battery manager line input voltage range.
INT bmPropertyMaxProbeOnString	1.3.6.1.4.1.3808.1.1.7.2.2	INTEGER	read-only	Battery manager max probes on a string supported.
INT bmPropertyProbesRating	1.3.6.1.4.1.3808.1.1.7.2.4	INTEGER	read-only	Battery probes model rating.
INT bmPropertyStringMax	1.3.6.1.4.1.3808.1.1.7.2.1	INTEGER	read-only	Battery manager max string count supported.
NTF bmSProbesWarning	1.3.6.1.4.1.3808.0.604			WARNING: Probe warning event. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the string index the probe located. The fifth argument is the battery index the probe located. The sixth argument is the alarm event specific identifier. The seventh argument is the trap information string.
NTF bmSystemAlarm	1.3.6.1.4.1.3808.0.600			ALARM: System alarm occurance. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the alarm event specific identifier. The fifth argument is the trap information string.
NTF bmSystemInfo	1.3.6.1.4.1.3808.0.602			INFO: System information. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the alarm event specific identifier. The fifth argument is the trap information string.
NTF bmSystemWarning	1.3.6.1.4.1.3808.0.601			WARNING: System warning occurance. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the alarm event specific identifier. The fifth argument is the trap information string.
NTF clientRegistered	1.3.6.1.4.1.3808.0.70			Information: PowerPanel client has been registered.
NTF clientRemoved	1.3.6.1.4.1.3808.0.71			Information: PowerPanel client has been removed.
NTF communicationEstablished	1.3.6.1.4.1.3808.0.8			INFORMATIONAL: Communication to the UPS has been established.
NTF communicationLost	1.3.6.1.4.1.3808.0.1			SEVERE: Communication with the UPS has been lost.
STR communityString	1.3.6.1.4.1.3808.2.1.2.1.3	DisplayString	read-write	The trap receiver community name.
NTF configFileUpload	1.3.6.1.4.1.3808.0.64			INFORMATION: Configuration file uploaded.
NTF configurationChanged	1.3.6.1.4.1.3808.0.69			INFORMATION: Configuration has been changed.
cps	1.3.6.1.4.1.3808
cpsmgmt	1.3.6.1.4.1.3808.2
INT deviceIndex	1.3.6.1.4.1.3808.1.1.1.5.1.2.1.1	INTEGER	read-only	The index of the equipment plugged into the UPS.
NTF deviceLoginInfo	1.3.6.1.4.1.3808.0.67			INFORMATION: Device login.
NTF deviceLogoutInfo	1.3.6.1.4.1.3808.0.68			INFORMATION: Device logout.
STR deviceName	1.3.6.1.4.1.3808.1.1.1.5.1.2.1.2	DisplayString	read-write	The name of the equipment plugged into the UPS.
NTF envConntected	1.3.6.1.4.1.3808.0.210			INFORMATION: The Environment Sensor has been connected.
NTF envDisconntected	1.3.6.1.4.1.3808.0.211			INFORMATION: The Environment Sensor has been disconnected.
NTF envDryContactAbnormal	1.3.6.1.4.1.3808.0.208			INFORMATION: The Contact is abnormal.
NTF envDryContactNormal	1.3.6.1.4.1.3808.0.209			INFORMATION: The Contact has returned from abnormal.
NTF envHighHumidityBack	1.3.6.1.4.1.3808.0.205			INFORMATION: The environment humidity return from high value.
NTF envHighHumidityViolation	1.3.6.1.4.1.3808.0.204			WARNING: The environment high humidity threshold has been violated.
NTF envHighTemperatureBack	1.3.6.1.4.1.3808.0.201			INFORMATION: The environment temperature returned from high value.
NTF envHighTemperatureViolation	1.3.6.1.4.1.3808.0.200			WARNING: The environment high temperature threshold has been violated.
envirContact	1.3.6.1.4.1.3808.1.1.4.4
envirContactEntry	1.3.6.1.4.1.3808.1.1.4.4.2.1		not-accessible	This gives access to contact entries
INT envirContactIndex	1.3.6.1.4.1.3808.1.1.4.4.2.1.1	INTEGER	read-only	The index to the contact of the environment sensor.
STR envirContactName	1.3.6.1.4.1.3808.1.1.4.4.2.1.2	DisplayString	read-write	Getting or setting the name of the contact of the environment sensor.
INT envirContactNormalState	1.3.6.1.4.1.3808.1.1.4.4.2.1.4	INTEGER	read-write	Set the contact normal state.
INT envirContactStatus	1.3.6.1.4.1.3808.1.1.4.4.2.1.3	INTEGER	read-only	Getting this OID will return the Contact Status.
envirContactTable	1.3.6.1.4.1.3808.1.1.4.4.2		not-accessible	Allows for getting of information of each contact of the environment sensor.
INT envirContactTableSize	1.3.6.1.4.1.3808.1.1.4.4.1	INTEGER	read-only	The number of the contact in the environment sensor.
envirHumid	1.3.6.1.4.1.3808.1.1.4.3
INT envirHumidHighThreshold	1.3.6.1.4.1.3808.1.1.4.3.2	INTEGER	read-write	The high relative humidity threshold of the environment sensor. The value expressed in persentage.
INT envirHumidHysteresis	1.3.6.1.4.1.3808.1.1.4.3.5	INTEGER	read-write	The number of degrees beyond the relative humidity thresholds at which an active relative humidity alarm will be cleared. This configuration setting applies to all relative humidity thresholds. Units are displayed in persentage.
INT envirHumidity	1.3.6.1.4.1.3808.1.1.4.3.1	INTEGER	read-only	The environment relative humidity expressed in persentage.
INT envirHumidLowThreshold	1.3.6.1.4.1.3808.1.1.4.3.3	INTEGER	read-write	The low relative humidity threshold of the environment sensor. The value expressed in persentage.
INT envirHumidRateOfChange	1.3.6.1.4.1.3808.1.1.4.3.4	INTEGER	read-write	The rate of change of the relative humidity. The value expressed in persentage per 5 minute.
envirIdent	1.3.6.1.4.1.3808.1.1.4.1
STR envirIdentLocation	1.3.6.1.4.1.3808.1.1.4.1.2	DisplayString	read-write	The location of the environment sensor. The maximum string size is device dependent.
STR envirIdentName	1.3.6.1.4.1.3808.1.1.4.1.1	DisplayString	read-write	The name of the environment sensor. The maximum string size is device dependent.
environmentSensor	1.3.6.1.4.1.3808.1.1.4
envirTemp	1.3.6.1.4.1.3808.1.1.4.2
INT envirTempCelsiusHighThreshold	1.3.6.1.4.1.3808.1.1.4.2.7	INTEGER	read-write	The high temperature threshold of the environment sensor. The value expressed in Celsius.
INT envirTempCelsiusHysteresis	1.3.6.1.4.1.3808.1.1.4.2.10	INTEGER	read-write	The number of degrees beyond the temperature thresholds at which an active temperature alarm will be cleared. This configuration setting applies to all temperature thresholds. Units are displayed in Celsius.
INT envirTempCelsiusLowThreshold	1.3.6.1.4.1.3808.1.1.4.2.8	INTEGER	read-write	The low temperature threshold of the environment sensor. The value expressed in Celsius.
INT envirTempCelsiusRateOfChange	1.3.6.1.4.1.3808.1.1.4.2.9	INTEGER	read-write	The rate of change of the temperature. The value expressed in Celsius per 5 minute.
INT envirTemperature	1.3.6.1.4.1.3808.1.1.4.2.1	INTEGER	read-only	The environment temperature expressed in 1/10 Fahrenheit
INT envirTemperatureCelsius	1.3.6.1.4.1.3808.1.1.4.2.6	INTEGER	read-only	The environment temperature expressed in 1/10 Celsius
INT envirTempHighThreshold	1.3.6.1.4.1.3808.1.1.4.2.2	INTEGER	read-write	The high temperature threshold of the environment sensor. The value expressed in Fahrenheit.
INT envirTempHysteresis	1.3.6.1.4.1.3808.1.1.4.2.5	INTEGER	read-write	The number of degrees beyond the temperature thresholds at which an active temperature alarm will be cleared. This configuration setting applies to all temperature thresholds. Units are displayed in Fahrenheit.
INT envirTempLowThreshold	1.3.6.1.4.1.3808.1.1.4.2.3	INTEGER	read-write	The low temperature threshold of the environment sensor. The value expressed in Fahrenheit.
INT envirTempRateOfChange	1.3.6.1.4.1.3808.1.1.4.2.4	INTEGER	read-write	The rate of change of the temperature. The value expressed in Fahrenheit per 5 minute.
NTF envLowHumdBack	1.3.6.1.4.1.3808.0.207			INFORMATION: The environment humidity return from low value.
NTF envLowHumidityViolation	1.3.6.1.4.1.3808.0.206			WARNING: The environment low humidity threshold has been violated.
NTF envLowTempBack	1.3.6.1.4.1.3808.0.203			INFORMATION: The environment temperature returned from low value.
NTF envLowTemperatureViolation	1.3.6.1.4.1.3808.0.202			WARNING: The environment low temperature threshold has been violated.
NTF envRateOfHumdChangeAbnormal	1.3.6.1.4.1.3808.0.213			INFORMATION: The rate of humidity change is abnormal.
NTF envRateOfTemperatureChangeAbnormal	1.3.6.1.4.1.3808.0.212			INFORMATION: The rate of temperature change is abnormal.
ePDU	1.3.6.1.4.1.3808.1.1.3
ePDU2	1.3.6.1.4.1.3808.1.1.6
ePDU2Bank	1.3.6.1.4.1.3808.1.1.6.5
ePDU2BankConfigEntry	1.3.6.1.4.1.3808.1.1.6.5.2.1		not-accessible	Configuration data from currently queried Rack PDU bank.
INT ePDU2BankConfigIndex	1.3.6.1.4.1.3808.1.1.6.5.2.1.1	INTEGER	read-only	The index to the Rack PDU bank configuration table entry.
INT ePDU2BankConfigLowLoadThreshold	1.3.6.1.4.1.3808.1.1.6.5.2.1.5	INTEGER	read-write	User-defined low load bank current threshold in Amps.
INT ePDU2BankConfigModuleIndex	1.3.6.1.4.1.3808.1.1.6.5.2.1.2	INTEGER	read-only	The Rack PDU numeric ID.
INT ePDU2BankConfigNearOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.5.2.1.6	INTEGER	read-write	User-defined near bank overload current warning threshold in Amps.
INT ePDU2BankConfigNumber	1.3.6.1.4.1.3808.1.1.6.5.2.1.3	INTEGER	read-only	The numeric bank ID.
INT ePDU2BankConfigOverloadRestriction	1.3.6.1.4.1.3808.1.1.6.5.2.1.4	INTEGER	read-write	This OID controls the behavior of a Switched Rack PDU bank when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding bank to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding bank to turn on if the ePDU2BankConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding bank to turn on if the ePDU2BankConfigOverloadThreshold OID is exceeded.
INT ePDU2BankConfigOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.5.2.1.7	INTEGER	read-write	User-defined bank overload current threshold in Amps
INT ePDU2BankConfigPeakLoadReset	1.3.6.1.4.1.3808.1.1.6.5.2.1.8	INTEGER	read-write	Setting this OID to reset (2) will cause the existing peak current value to be replaced by the present load current value. Getting this OID will do nothing and return the noOperation(1) value.
ePDU2BankConfigTable	1.3.6.1.4.1.3808.1.1.6.5.2		not-accessible	A table of Rack PDU bank configuration data.
ePDU2BankInfoEntry	1.3.6.1.4.1.3808.1.1.6.5.3.1		not-accessible	Information data from currently queried Rack PDU bank.
INT ePDU2BankInfoIndex	1.3.6.1.4.1.3808.1.1.6.5.3.1.1	INTEGER	read-only	The index to the Rack PDU bank properties table entry.
INT ePDU2BankInfoModuleIndex	1.3.6.1.4.1.3808.1.1.6.5.3.1.2	INTEGER	read-only	The Rack PDU numeric ID.
INT ePDU2BankInfoNumber	1.3.6.1.4.1.3808.1.1.6.5.3.1.3	INTEGER	read-only	The numeric bank ID.
ePDU2BankInfoTable	1.3.6.1.4.1.3808.1.1.6.5.3		not-accessible	A table of Rack PDU bank information.
ePDU2BankStatusEntry	1.3.6.1.4.1.3808.1.1.6.5.4.1		not-accessible	Status data from currently queried Rack PDU bank
INT ePDU2BankStatusIndex	1.3.6.1.4.1.3808.1.1.6.5.4.1.1	INTEGER	read-only	The index to the Rack PDU bank status table entry.
GAU ePDU2BankStatusLoad	1.3.6.1.4.1.3808.1.1.6.5.4.1.5	Gauge	read-only	Indicates the current draw, in tenths of Amps, of the load on the Rack PDU bank being queried.
INT ePDU2BankStatusLoadState	1.3.6.1.4.1.3808.1.1.6.5.4.1.4	INTEGER	read-only	Indicates the present load status of the Rack PDU bank being queried.
INT ePDU2BankStatusModuleIndex	1.3.6.1.4.1.3808.1.1.6.5.4.1.2	INTEGER	read-only	The Rack PDU numeric ID.
INT ePDU2BankStatusNumber	1.3.6.1.4.1.3808.1.1.6.5.4.1.3	INTEGER	read-only	The numeric bank ID.
GAU ePDU2BankStatusPeakLoad	1.3.6.1.4.1.3808.1.1.6.5.4.1.6	Gauge	read-only	The peak current of the Rack PDU bank load in tenths of Amps.
STR ePDU2BankStatusPeakLoadStartTime	1.3.6.1.4.1.3808.1.1.6.5.4.1.8	DisplayString	read-only	Indicates the date and time of the last bank peak current reset.
STR ePDU2BankStatusPeakLoadTimestamp	1.3.6.1.4.1.3808.1.1.6.5.4.1.7	DisplayString	read-only	Indicates the date and time the bank peak current occurred.
ePDU2BankStatusTable	1.3.6.1.4.1.3808.1.1.6.5.4		not-accessible	A table of Rack PDU bank status data
INT ePDU2BankTableSize	1.3.6.1.4.1.3808.1.1.6.5.1	INTEGER	read-only	A Host Rack PDU response total bank number of Rack PDUs on daisy chain. Rack PDU as a Slave can only response itself number of bank.
ePDU2Device	1.3.6.1.4.1.3808.1.1.6.3
INT ePDU2DeviceConfigColdstartDelay	1.3.6.1.4.1.3808.1.1.6.3.2.1.7	INTEGER	read-write	The amount of delay, measured in seconds, between when power is provided to the Rack PDU and when the Rack PDU provides basic master power to the outlets. Allowed values are: -1 - never apply power automatically. 0 - apply power immediately. 1 to 300 - delay up to 300 seconds (5 minutes).
STR ePDU2DeviceConfigContact	1.3.6.1.4.1.3808.1.1.6.3.2.1.5	DisplayString	read-write	A user-defined string identifying the person to contact of the Rack PDU.
INT ePDU2DeviceConfigCurrentLowLoadThreshold	1.3.6.1.4.1.3808.1.1.6.3.2.1.8	INTEGER	read-write	User-defined low current draw alarm threshold, measured in Amps.
INT ePDU2DeviceConfigCurrentNearOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.3.2.1.9	INTEGER	read-write	User-defined near overload current threshold, measured in Amps.
INT ePDU2DeviceConfigCurrentOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.3.2.1.10	INTEGER	read-write	User-defined current overload threshold, measured in Amps.
INT ePDU2DeviceConfigDisplayOrientation	1.3.6.1.4.1.3808.1.1.6.3.2.1.6	INTEGER	read-write	Getting this OID will return the intended physical orientation of the Seven-Segment Display. displayNormal(1) indicates Normal. displayReverse(2)indicates Upside-Down. displayRotate90(3) indicates rotate 90 degree. displayRotate270(4) indicates rotate 270 degree. displayAuto(5) indicates auto-detect and rotate.
INT ePDU2DeviceConfigEnergyReset	1.3.6.1.4.1.3808.1.1.6.3.2.1.12	INTEGER	read-write	Setting this OID to resetAll (2) will cause the device energy meter value to be reset to zero. Setting this OID to resetDevice (3) to reset the Rack PDU only. Setting this OID to resetOutlets (4) to reset the PDU outlets only. Getting this OID in models that support this feature will do nothing and return the noOperation(1) value.
ePDU2DeviceConfigEntry	1.3.6.1.4.1.3808.1.1.6.3.2.1		not-accessible	Configuration data from Rack PDU being queried.
INT ePDU2DeviceConfigIndex	1.3.6.1.4.1.3808.1.1.6.3.2.1.1	INTEGER	read-only	The index to the Rack PDU table entry.
STR ePDU2DeviceConfigLocation	1.3.6.1.4.1.3808.1.1.6.3.2.1.4	DisplayString	read-write	A user-defined string identifying the location of the Rack PDU.
INT ePDU2DeviceConfigModuleIndex	1.3.6.1.4.1.3808.1.1.6.3.2.1.2	INTEGER	read-only	The Rack PDU numeric ID.
STR ePDU2DeviceConfigName	1.3.6.1.4.1.3808.1.1.6.3.2.1.3	DisplayString	read-write	A user-defined string identifying the name of Rack PDU.
INT ePDU2DeviceConfigPeakLoadReset	1.3.6.1.4.1.3808.1.1.6.3.2.1.11	INTEGER	read-write	Setting this OID to resetAll (2) will cause the existing peak current value of Rack PDU and its outlets to be replaced by the current load current value. Setting this OID to resetDevice (3) to reset the Rack PDU only. Setting this OID to resetOutlets (4) to reset the PDU outlets only. Getting this OID will do nothing and return the noOperation(1) value.
INT ePDU2DeviceConfigPowerLowLoadThreshold	1.3.6.1.4.1.3808.1.1.6.3.2.1.13	INTEGER	read-write	User-defined low power draw alarm threshold, measured in Watts.
INT ePDU2DeviceConfigPowerNearOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.3.2.1.14	INTEGER	read-write	User-defined near overload power threshold, measured in Watts.
INT ePDU2DeviceConfigPowerOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.3.2.1.15	INTEGER	read-write	User-defined power overload threshold, measured in Watts.
ePDU2DeviceConfigTable	1.3.6.1.4.1.3808.1.1.6.3.2		not-accessible	A table of Rack PDU configuration data.
INT ePDU2DeviceControlCommand	1.3.6.1.4.1.3808.1.1.6.3.5.1.4	INTEGER	read-write	Setting this OID to immediateAllOn (1) will turn all outlets on immediately. Setting this OID to immediateAllOff (2) will turn all outlets off immediately. Setting this OID to immediateAllReboot (3) will cause an immediateAllOff command to be performed. Once all outlets are off, the Switched Rack PDU will then delay the ePDU2OutletSwitchedConfigRebootDuration OID time, and then perform an immediateAllOn command. Setting this OID to delayedAllOn (4) will turn all outlets on as defined by each outlet's ePDU2OutletSwitchedConfigPowerOnTime OID value. Setting this OID to delayedAllOff (5) will turn all outlets off as defined by each outlet's ePDU2OutletSwitchedConfigPowerOffTime OID value. Setting this OID to delayedAllReboot (6) will cause a delayedAllOff command to be performed. Once all outlets are off, the Switched Rack PDU will then delay the largest ePDU2OutletSwitchedConfigRebootDuration OID time, and then perform a delayedAllOn command. Setting this OID to cancelAllPendingCommand (7) will cause all pending commands on the Switched Rack PDU to be cancelled. Setting this OID to noCommand (8) will have no effect. Getting this OID will return the noCommand (8) value.
ePDU2DeviceControlEntry	1.3.6.1.4.1.3808.1.1.6.3.5.1		not-accessible	Control data from Rack PDU being queried.
INT ePDU2DeviceControlIndex	1.3.6.1.4.1.3808.1.1.6.3.5.1.1	INTEGER	read-only	The index to the Rack PDU control table entry.
INT ePDU2DeviceControlModuleIndex	1.3.6.1.4.1.3808.1.1.6.3.5.1.2	INTEGER	read-only	The Rack PDU numeric ID.
STR ePDU2DeviceControlName	1.3.6.1.4.1.3808.1.1.6.3.5.1.3	DisplayString	read-only	A user-defined string identifying the name of the Rack PDU.
ePDU2DeviceControlTable	1.3.6.1.4.1.3808.1.1.6.3.5		not-accessible	A table of Rack PDU control data.
INT ePDU2DeviceInfoBreakerRating	1.3.6.1.4.1.3808.1.1.6.3.3.1.10	INTEGER	read-only	The maximum current rating, measured in Amps, for the Rack PDU. Getting this OID will return rating of the circuit breakers on the device if it has any.
ePDU2DeviceInfoEntry	1.3.6.1.4.1.3808.1.1.6.3.3.1		not-accessible	Information of the Rack PDU being queried.
INT ePDU2DeviceInfoIndex	1.3.6.1.4.1.3808.1.1.6.3.3.1.1	INTEGER	read-only	The index to the Rack PDU Information table entry.
INT ePDU2DeviceInfoMeteredOutlets	1.3.6.1.4.1.3808.1.1.6.3.3.1.7	INTEGER	read-only	The number of metered outlets on the Rack PDU.
INT ePDU2DeviceInfoModuleIndex	1.3.6.1.4.1.3808.1.1.6.3.3.1.2	INTEGER	read-only	The Rack PDU numeric ID.
STR ePDU2DeviceInfoName	1.3.6.1.4.1.3808.1.1.6.3.3.1.3	DisplayString	read-only	A user-defined string identifying the name of the Rack PDU.
INT ePDU2DeviceInfoNumBreakers	1.3.6.1.4.1.3808.1.1.6.3.3.1.9	INTEGER	read-only	The number of metered banks present in the Rack PDU.
INT ePDU2DeviceInfoNumOutlets	1.3.6.1.4.1.3808.1.1.6.3.3.1.5	INTEGER	read-only	The number of outlets on the Rack PDU.
INT ePDU2DeviceInfoNumPhases	1.3.6.1.4.1.3808.1.1.6.3.3.1.8	INTEGER	read-only	The number of phases present in the Rack PDU.
INT ePDU2DeviceInfoOrientation	1.3.6.1.4.1.3808.1.1.6.3.3.1.11	INTEGER	read-only	Rack PDU orientation.
INT ePDU2DeviceInfoOutletLayout	1.3.6.1.4.1.3808.1.1.6.3.3.1.12	INTEGER	read-only	Getting this OID will return outlet layout for the device. SeqPhaseToNeutral(1) indicates outlet layout as follows: 1:1-N,2:2-N,3:3-N,4:1-N,5:2-N,... SeqPhaseToPhase(2) indicates outlet layout as follows: 1:1-2,2:2-3,3:3-1,4:1-2,5:2-3,... SeqPhToNeu21PhToPh(3) indicates outlet layout as follows: 1:1-N,2:2-N...21:3-N,22:1-2,23:2-3,24:3-1,... SeqPhToPhGrouped(4) indicates outlet layout as follows: Otlts1-8::(3-1),Otlts9-16::(2-3),Otlts17-24::(1-2).
INT ePDU2DeviceInfoRating	1.3.6.1.4.1.3808.1.1.6.3.3.1.4	INTEGER	read-only	The electrical rating of the Rack PDU.
INT ePDU2DeviceInfoSwitchedOutlets	1.3.6.1.4.1.3808.1.1.6.3.3.1.6	INTEGER	read-only	The number of switched outlets on the Rack PDU.
ePDU2DeviceInfoTable	1.3.6.1.4.1.3808.1.1.6.3.3		not-accessible	A table of Rack PDU information.
GAU ePDU2DeviceStatusApparentPower	1.3.6.1.4.1.3808.1.1.6.3.4.1.15	Gauge	read-only	The apparent power consumption of the Rack PDU load in VoltAmps (VA).
INT ePDU2DeviceStatusCommandPending	1.3.6.1.4.1.3808.1.1.6.3.4.1.11	INTEGER	read-only	Indicates whether or not the device is processing a pending command.
GAU ePDU2DeviceStatusCurrentLoad	1.3.6.1.4.1.3808.1.1.6.3.4.1.5	Gauge	read-only	The power consumption of the Rack PDU load in tenths of Amps.
GAU ePDU2DeviceStatusCurrentPeakLoad	1.3.6.1.4.1.3808.1.1.6.3.4.1.6	Gauge	read-only	The peak power consumption of the Rack PDU load in tenths of Amps.
GAU ePDU2DeviceStatusEnergy	1.3.6.1.4.1.3808.1.1.6.3.4.1.9	Gauge	read-only	A user resettable energy meter measuring Rack PDU load energy consumption in tenths of kilowatt-hours.
STR ePDU2DeviceStatusEnergyStartTime	1.3.6.1.4.1.3808.1.1.6.3.4.1.10	DisplayString	read-only	Indicates the date and time of the last device energy meter reset.
ePDU2DeviceStatusEntry	1.3.6.1.4.1.3808.1.1.6.3.4.1		not-accessible	Status data from the Rack PDU being queried.
INT ePDU2DeviceStatusIndex	1.3.6.1.4.1.3808.1.1.6.3.4.1.1	INTEGER	read-only	The index to the Rack PDU status table entry.
INT ePDU2DeviceStatusLoadState	1.3.6.1.4.1.3808.1.1.6.3.4.1.4	INTEGER	read-only	Indicates the present load status of the Rack PDU.
INT ePDU2DeviceStatusModuleIndex	1.3.6.1.4.1.3808.1.1.6.3.4.1.2	INTEGER	read-only	The Rack PDU numeric ID
STR ePDU2DeviceStatusName	1.3.6.1.4.1.3808.1.1.6.3.4.1.3	DisplayString	read-only	A user-defined string identifying the name of the Rack PDU.
STR ePDU2DeviceStatusPeakLoadStartTime	1.3.6.1.4.1.3808.1.1.6.3.4.1.8	DisplayString	read-only	Indicates the date and time of the last device peak load reset.
STR ePDU2DeviceStatusPeakLoadTimestamp	1.3.6.1.4.1.3808.1.1.6.3.4.1.7	DisplayString	read-only	Indicates the date and time that peak load occurred.
GAU ePDU2DeviceStatusPowerFactor	1.3.6.1.4.1.3808.1.1.6.3.4.1.16	Gauge	read-only	The power factor of the Rack PDU load in hundredths.
GAU ePDU2DeviceStatusPowerLoad	1.3.6.1.4.1.3808.1.1.6.3.4.1.18	Gauge	read-only	The power consumption of the Rack PDU load in Watts.
GAU ePDU2DeviceStatusPowerPeakLoad	1.3.6.1.4.1.3808.1.1.6.3.4.1.19	Gauge	read-only	The peak power consumption of the Rack PDU load in Watts.
INT ePDU2DeviceStatusPowerSupply1Status	1.3.6.1.4.1.3808.1.1.6.3.4.1.13	INTEGER	read-only	Indicates whether or not an alarm is active in Power Supply 1.
INT ePDU2DeviceStatusPowerSupply2Status	1.3.6.1.4.1.3808.1.1.6.3.4.1.14	INTEGER	read-only	Indicates whether or not an alarm is active in Power Supply 2.
INT ePDU2DeviceStatusPowerSupplyAlarm	1.3.6.1.4.1.3808.1.1.6.3.4.1.12	INTEGER	read-only	Indicates a power supply alarm is active when value equals alarm (2).
INT ePDU2DeviceStatusRoleType	1.3.6.1.4.1.3808.1.1.6.3.4.1.17	INTEGER	read-only	Get this oid shows the role the PDU played on Daisy Chain Group. The PDU as a Host can access whole ePDU2 content, and the PDU be standalong or a Slave can access itself instead.
ePDU2DeviceStatusTable	1.3.6.1.4.1.3808.1.1.6.3.4		not-accessible	A table of Rack PDU current status.
INT ePDU2DeviceTableSize	1.3.6.1.4.1.3808.1.1.6.3.1	INTEGER	read-only	A Host Rack PDU response total number of Rack PDUs on daisy chain. Rack PDU as a Slave can only response 1.
ePDU2Group	1.3.6.1.4.1.3808.1.1.6.8
INT ePDU2GroupEnergyReset	1.3.6.1.4.1.3808.1.1.6.8.4	INTEGER	read-write	Setting this OID to reset (2) will cause the device energy meter value on each device in the Rack PDU Daisy Chain group to be reset to zero. Getting this OID in models that support this feature will do nothing and return the noOperation(1) value.
INT ePDU2GroupNumberOfDevices	1.3.6.1.4.1.3808.1.1.6.8.1	INTEGER	read-only	Getting this OID will return the number of Rack PDU devices contributing to the Daisy Chain group power and energy values. Queries to slave units in an Daisy Chain group will return 0.
INT ePDU2GroupPeakRecordReset	1.3.6.1.4.1.3808.1.1.6.8.5	INTEGER	read-write	Setting this OID to reset (2) will cause the device peak record value on each device in the Rack PDU Daisy Chain group to be reset to current load/power. Getting this OID in models that support this feature will do nothing and return the noOperation(1) value.
GAU ePDU2GroupTotalEnergy	1.3.6.1.4.1.3808.1.1.6.8.3	Gauge	read-only	Getting this OID will return the total energy consumption of the Rack PDU Daisy Chain group devices in tenths of kilowatt-hours. To reset the energy meters for each of the Rack PDU devices that contribute to this value, see the ePDU2GroupEnergyReset OID. To view the start time for each of the Rack PDU device energy meters that contribute to this value, see the ePDU2DeviceStatusEnergyStartTime OID. Queries to slave units in an Daisy Chain group will return 0.
GAU ePDU2GroupTotalPower	1.3.6.1.4.1.3808.1.1.6.8.2	Gauge	read-only	Getting this OID will return the total power consumption of the Rack PDU Daisy Chain group devices in watts. Queries to slave units in an Daisy Chain group will return 0.
ePDU2Ident	1.3.6.1.4.1.3808.1.1.6.2
STR ePDU2IdentContact	1.3.6.1.4.1.3808.1.1.6.2.2.1.5	DisplayString	read-only	A user-defined string identifying the person to contact of the Rack PDU.
STR ePDU2IdentDateOfManufacture	1.3.6.1.4.1.3808.1.1.6.2.2.1.8	DisplayString	read-only	The date the Rack PDU was manufactured in mm/dd/yyyy format.
ePDU2IdentEntry	1.3.6.1.4.1.3808.1.1.6.2.2.1		not-accessible	Identification data from Rack PDU being queried.
STR ePDU2IdentFirmwareRev	1.3.6.1.4.1.3808.1.1.6.2.2.1.7	DisplayString	read-only	The Rack PDU firmware version.
STR ePDU2IdentHardwareRev	1.3.6.1.4.1.3808.1.1.6.2.2.1.6	DisplayString	read-only	The Rack PDU hardware version.
INT ePDU2IdentIndex	1.3.6.1.4.1.3808.1.1.6.2.2.1.1	INTEGER	read-only	The index to the Rack PDU identification table entry.
INT ePDU2IdentIndicator	1.3.6.1.4.1.3808.1.1.6.2.2.1.11	INTEGER	read-write	PDU will perform a panel indicator test when the variable is set to testIndicators(2). It is no effective to set this value to noTestIndicators(1).
STR ePDU2IdentLocation	1.3.6.1.4.1.3808.1.1.6.2.2.1.4	DisplayString	read-only	A user-defined string identifying the location of the Rack PDU.
STR ePDU2IdentModelName	1.3.6.1.4.1.3808.1.1.6.2.2.1.9	DisplayString	read-only	The Rack PDU model number.
INT ePDU2IdentModuleIndex	1.3.6.1.4.1.3808.1.1.6.2.2.1.2	INTEGER	read-only	The Rack PDU identification table entry numeric ID.
STR ePDU2IdentName	1.3.6.1.4.1.3808.1.1.6.2.2.1.3	DisplayString	read-only	A user-defined string identifying the name of the Rack PDU.
STR ePDU2IdentSerialNumber	1.3.6.1.4.1.3808.1.1.6.2.2.1.10	DisplayString	read-only	The Rack PDU serial number.
ePDU2IdentTable	1.3.6.1.4.1.3808.1.1.6.2.2		not-accessible	A table of Rack PDU identification information.
INT ePDU2IdentTableSize	1.3.6.1.4.1.3808.1.1.6.2.1	INTEGER	read-only	PDU as a Host response total PDU ident number on daisy chain. PDU as a Slave can only response 1.
ePDU2Outlet	1.3.6.1.4.1.3808.1.1.6.6
ePDU2OutletMetered	1.3.6.1.4.1.3808.1.1.6.6.2
ePDU2OutletMeteredConfigEntry	1.3.6.1.4.1.3808.1.1.6.6.2.2.1		not-accessible	Configuration data from currently queried Rack PDU metered outlet.
INT ePDU2OutletMeteredConfigIndex	1.3.6.1.4.1.3808.1.1.6.6.2.2.1.1	INTEGER	read-only	The index to the Rack PDU metered outlet configuration table entry.
INT ePDU2OutletMeteredConfigLowLoadThreshold	1.3.6.1.4.1.3808.1.1.6.6.2.2.1.5	INTEGER	read-write	User-defined outlet low load current threshold in Watts.
INT ePDU2OutletMeteredConfigModuleIndex	1.3.6.1.4.1.3808.1.1.6.6.2.2.1.2	INTEGER	read-only	The user-defined Rack PDU numeric ID.
STR ePDU2OutletMeteredConfigName	1.3.6.1.4.1.3808.1.1.6.6.2.2.1.4	DisplayString	read-write	The user-defined metered outlet name string.
INT ePDU2OutletMeteredConfigNearOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.6.2.2.1.6	INTEGER	read-write	User-defined outlet near overload warning threshold in Watts.
INT ePDU2OutletMeteredConfigNumber	1.3.6.1.4.1.3808.1.1.6.6.2.2.1.3	INTEGER	read-only	The numeric metered outlet ID.
INT ePDU2OutletMeteredConfigOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.6.2.2.1.7	INTEGER	read-write	User-defined outlet overload current threshold in Watts.
ePDU2OutletMeteredConfigTable	1.3.6.1.4.1.3808.1.1.6.6.2.2		not-accessible	A table of Rack PDU metered outlet configuration data.
INT ePDU2OutletMeteredInfoBank	1.3.6.1.4.1.3808.1.1.6.6.2.3.1.7	INTEGER	read-only	This outlet's numeric bank ID.
ePDU2OutletMeteredInfoEntry	1.3.6.1.4.1.3808.1.1.6.6.2.3.1		not-accessible	Information of currently queried Rack PDU metered outlet.
INT ePDU2OutletMeteredInfoIndex	1.3.6.1.4.1.3808.1.1.6.6.2.3.1.1	INTEGER	read-only	The index to the Rack PDU metered information table entry.
INT ePDU2OutletMeteredInfoLayout	1.3.6.1.4.1.3808.1.1.6.6.2.3.1.5	INTEGER	read-only	This OID describes the phase connections of the referenced outlet as follows: seqPhase1ToNeutral(1) indicates that the outlet is wired from Phase 1 to Neutral. seqPhase2ToNeutral(2) indicates that the outlet is wired from Phase 2 to Neutral. seqPhase3ToNeutral(3) indicates that the outlet is wired from Phase 3 to Neutral. seqPhase1ToPhase2(4) indicates that the outlet is wired from Phase 1 to Phase 2. seqPhase2ToPhase3(5) indicates that the outlet is wired from Phase 2 to Phase 3. seqPhase3ToPhase1(6) indicates that the outlet is wired from Phase 3 to Phase 1.
INT ePDU2OutletMeteredInfoModuleIndex	1.3.6.1.4.1.3808.1.1.6.6.2.3.1.2	INTEGER	read-only	The Rack PDU numeric ID.
STR ePDU2OutletMeteredInfoName	1.3.6.1.4.1.3808.1.1.6.6.2.3.1.4	DisplayString	read-only	The user-defined metered outlet name string.
INT ePDU2OutletMeteredInfoNumber	1.3.6.1.4.1.3808.1.1.6.6.2.3.1.3	INTEGER	read-only	The numeric metered outlet ID.
INT ePDU2OutletMeteredInfoRating	1.3.6.1.4.1.3808.1.1.6.6.2.3.1.6	INTEGER	read-only	Maximum power rating of Rack PDU metered outlet.
ePDU2OutletMeteredInfoTable	1.3.6.1.4.1.3808.1.1.6.6.2.3		not-accessible	A table of Rack PDU metered outlet information.
GAU ePDU2OutletMeteredStatusActivePower	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.7	Gauge	read-only	Getting this OID will return the measured Outlet load for an Outlet Monitored Rack PDU in watts.
INT ePDU2OutletMeteredStatusAlarm	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.5	INTEGER	read-only	Getting this OID will return the current outlet alarm.
GAU ePDU2OutletMeteredStatusEnergy	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.11	Gauge	read-only	Energy meter measuring Rack PDU load energy consumption in tenths of kilowatt-hours.
STR ePDU2OutletMeteredStatusEnergyStart	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.12	DisplayString	read-only	Indicates the date and time of the last device energy meter reset.
ePDU2OutletMeteredStatusEntry	1.3.6.1.4.1.3808.1.1.6.6.2.4.1		not-accessible	Status data from currently queried Rack PDU metered outlet.
INT ePDU2OutletMeteredStatusIndex	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.1	INTEGER	read-only	The index to the Rack PDU metered status table entry.
GAU ePDU2OutletMeteredStatusLoad	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.6	Gauge	read-only	Getting this OID will return the measured Outlet load for an Outlet Monitored Rack PDU in tenths of Amps.
INT ePDU2OutletMeteredStatusModuleIndex	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.2	INTEGER	read-only	The Rack PDU numeric ID.
STR ePDU2OutletMeteredStatusName	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.4	DisplayString	read-only	The user-defined metered outlet name string.
INT ePDU2OutletMeteredStatusNumber	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.3	INTEGER	read-only	The numeric metered outlet ID.
GAU ePDU2OutletMeteredStatusPeakPower	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.8	Gauge	read-only	The peak power consumption of the Rack PDU load in watts.
STR ePDU2OutletMeteredStatusPeakPowerStartTime	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.10	DisplayString	read-only	Get this oid shows the date and time that peak power consumption started.
STR ePDU2OutletMeteredStatusPeakPowerTimestamp	1.3.6.1.4.1.3808.1.1.6.6.2.4.1.9	DisplayString	read-only	Get this oid shows the date and time that peak power consumption occurred.
ePDU2OutletMeteredStatusTable	1.3.6.1.4.1.3808.1.1.6.6.2.4		not-accessible	A table of Rack PDU metered outlet status data.
INT ePDU2OutletMeteredTableSize	1.3.6.1.4.1.3808.1.1.6.6.2.1	INTEGER	read-only	The number of metered outlets on connected Rack PDUs.
ePDU2OutletSwitched	1.3.6.1.4.1.3808.1.1.6.6.1
ePDU2OutletSwitchedConfigEntry	1.3.6.1.4.1.3808.1.1.6.6.1.2.1		not-accessible	Configuration data from currently queried Rack PDU switched outlet.
INT ePDU2OutletSwitchedConfigIndex	1.3.6.1.4.1.3808.1.1.6.6.1.2.1.1	INTEGER	read-only	The index to the Rack PDU switched outlet configuration table entry.
INT ePDU2OutletSwitchedConfigModuleIndex	1.3.6.1.4.1.3808.1.1.6.6.1.2.1.2	INTEGER	read-only	The Rack PDU numeric ID.
STR ePDU2OutletSwitchedConfigName	1.3.6.1.4.1.3808.1.1.6.6.1.2.1.4	DisplayString	read-write	The user-defined switched outlet name string.
INT ePDU2OutletSwitchedConfigNumber	1.3.6.1.4.1.3808.1.1.6.6.1.2.1.3	INTEGER	read-only	The numeric switched outlet ID.
INT ePDU2OutletSwitchedConfigPowerOffTime	1.3.6.1.4.1.3808.1.1.6.6.1.2.1.6	INTEGER	read-write	The amount of time (in seconds) the outlet will delay powering off when a command that requires a turn-off delay is issued. Allowed values are: -1 - never power off. 0 - power off immediately. 1 to 7200 - power off up to 7200 seconds after being commanded.
INT ePDU2OutletSwitchedConfigPowerOnTime	1.3.6.1.4.1.3808.1.1.6.6.1.2.1.5	INTEGER	read-write	The amount of time (in seconds) the outlet will delay powering on at coldstart or when a command that requires a turn-on delay is issued. Allowed values are: -1 - never power on. 0 - power on immediately. 1 to 7200 - power on up to 7200 seconds after being commanded.
INT ePDU2OutletSwitchedConfigRebootDuration	1.3.6.1.4.1.3808.1.1.6.6.1.2.1.7	INTEGER	read-write	During a reboot sequence, power is turned off and then back on. This OID defines the amount of time to wait, in seconds, after turning the power off, at the start of the sequence, before turning power back on, at the end of the reboot sequence. Allowed range is any value between 5 and 60 seconds (1 minute).
ePDU2OutletSwitchedConfigTable	1.3.6.1.4.1.3808.1.1.6.6.1.2		not-accessible	A table of Rack PDU switched outlet configuration data.
INT ePDU2OutletSwitchedControlCommand	1.3.6.1.4.1.3808.1.1.6.6.1.5.1.5	INTEGER	read-write	Getting this variable will return the outlet state. If the outlet is on, the immediateOn (1) value will be returned. If the outlet is off, the immediateOff (2) value will be returned. Setting this variable to immediateOn (1) will immediately turn the outlet on. Setting this variable to immediateOff (2) will immediately turn the outlet off. Setting this variable to immediateReboot (3) will immediately reboot the outlet. Setting this variable to delayedOn (4) will turn the outlet on after the ePDUOutletConfigPowerOnTime OID time has elapsed. Setting this variable to delayedOff (5) will turn the outlet off after the ePDUOutletConfigPowerOffTime OID time has elapsed. Setting this variable to delayedReboot (6) will cause the Switched Rack PDU to perform a delayedOff command, wait the ePDUOutletConfigRebootDuration OID time, and then perform a delayedOn command. Setting this variable to cancelPendingCommand (7) will cause any pending command to this outlet to be canceled. Setting this variable to outletIdentify (8) will cause PDU LED to display the number of the outlet.
ePDU2OutletSwitchedControlEntry	1.3.6.1.4.1.3808.1.1.6.6.1.5.1		not-accessible	Control data for currently queried Rack PDU switched outlet.
INT ePDU2OutletSwitchedControlIndex	1.3.6.1.4.1.3808.1.1.6.6.1.5.1.1	INTEGER	read-only	The index to the Rack PDU switched outlet control data table entry.
INT ePDU2OutletSwitchedControlModuleIndex	1.3.6.1.4.1.3808.1.1.6.6.1.5.1.2	INTEGER	read-only	The user-defined Rack PDU numeric ID.
STR ePDU2OutletSwitchedControlName	1.3.6.1.4.1.3808.1.1.6.6.1.5.1.4	DisplayString	read-only	The user-defined switched outlet name string.
INT ePDU2OutletSwitchedControlNumber	1.3.6.1.4.1.3808.1.1.6.6.1.5.1.3	INTEGER	read-only	The numeric switched outlet ID.
ePDU2OutletSwitchedControlTable	1.3.6.1.4.1.3808.1.1.6.6.1.5		not-accessible	A table of Rack PDU switched outlet control data.
INT ePDU2OutletSwitchedInfoBank	1.3.6.1.4.1.3808.1.1.6.6.1.3.1.6	INTEGER	read-only	The numeric bank ID.
ePDU2OutletSwitchedInfoEntry	1.3.6.1.4.1.3808.1.1.6.6.1.3.1		not-accessible	Information of the currently queried Rack PDU switched outlet.
INT ePDU2OutletSwitchedInfoIndex	1.3.6.1.4.1.3808.1.1.6.6.1.3.1.1	INTEGER	read-only	The index to the Rack PDU switched outlet information table entry.
INT ePDU2OutletSwitchedInfoModuleIndex	1.3.6.1.4.1.3808.1.1.6.6.1.3.1.2	INTEGER	read-only	The Rack PDU numeric ID.
STR ePDU2OutletSwitchedInfoName	1.3.6.1.4.1.3808.1.1.6.6.1.3.1.4	DisplayString	read-only	The numeric switched outlet name.
INT ePDU2OutletSwitchedInfoNumber	1.3.6.1.4.1.3808.1.1.6.6.1.3.1.3	INTEGER	read-only	The numeric switched outlet ID.
INT ePDU2OutletSwitchedInfoPhaseLayout	1.3.6.1.4.1.3808.1.1.6.6.1.3.1.5	INTEGER	read-only	This OID describes the phase connections of the referenced outlet as follows: seqPhase1ToNeutral(1) indicates that the outlet is wired from Phase 1 to Neutral. seqPhase2ToNeutral(2) indicates that the outlet is wired from Phase 2 to Neutral. seqPhase3ToNeutral(3) indicates that the outlet is wired from Phase 3 to Neutral. seqPhase1ToPhase2(4) indicates that the outlet is wired from Phase 1 to Phase 2. seqPhase2ToPhase3(5) indicates that the outlet is wired from Phase 2 to Phase 3. seqPhase3ToPhase1(6) indicates that the outlet is wired from Phase 3 to Phase 1.
ePDU2OutletSwitchedInfoTable	1.3.6.1.4.1.3808.1.1.6.6.1.3		not-accessible	A table of Rack PDU switched outlet information.
INT ePDU2OutletSwitchedStatusCommandPending	1.3.6.1.4.1.3808.1.1.6.6.1.4.1.6	INTEGER	read-only	Getting this variable will return the command pending state of the outlet. If a command is pending on the outlet, the outletStatusCommandPending (1) value will be returned. If there is not a command pending on the outlet, the outletStatusNoCommandPending (2) will be returned.
ePDU2OutletSwitchedStatusEntry	1.3.6.1.4.1.3808.1.1.6.6.1.4.1		not-accessible	Status information for currently queried Rack PDU switched outlet.
INT ePDU2OutletSwitchedStatusIndex	1.3.6.1.4.1.3808.1.1.6.6.1.4.1.1	INTEGER	read-only	The index to the Rack PDU switched outlet status information table entry.
INT ePDU2OutletSwitchedStatusModuleIndex	1.3.6.1.4.1.3808.1.1.6.6.1.4.1.2	INTEGER	read-only	The Rack PDU numeric ID.
STR ePDU2OutletSwitchedStatusName	1.3.6.1.4.1.3808.1.1.6.6.1.4.1.4	DisplayString	read-only	The user-defined switched outlet name string.
INT ePDU2OutletSwitchedStatusNumber	1.3.6.1.4.1.3808.1.1.6.6.1.4.1.3	INTEGER	read-only	The numeric switched outlet ID.
INT ePDU2OutletSwitchedStatusState	1.3.6.1.4.1.3808.1.1.6.6.1.4.1.5	INTEGER	read-only	Indicates the present switch state of the Rack PDU switched outlet being queried.
ePDU2OutletSwitchedStatusTable	1.3.6.1.4.1.3808.1.1.6.6.1.4		not-accessible	A table of Rack PDU switched outlet status information.
INT ePDU2OutletSwitchedTableSize	1.3.6.1.4.1.3808.1.1.6.6.1.1	INTEGER	read-only	The number of switched outlets on connected Rack PDUs.
ePDU2Phase	1.3.6.1.4.1.3808.1.1.6.4
ePDU2PhaseConfigEntry	1.3.6.1.4.1.3808.1.1.6.4.2.1		not-accessible	Configuration data from currently queried Rack PDU phase.
INT ePDU2PhaseConfigIndex	1.3.6.1.4.1.3808.1.1.6.4.2.1.1	INTEGER	read-only	The index to the Rack PDU phase configuration table entry.
INT ePDU2PhaseConfigLowLoadThreshold	1.3.6.1.4.1.3808.1.1.6.4.2.1.5	INTEGER	read-write	User-defined low load phase current threshold in Amps.
INT ePDU2PhaseConfigModuleIndex	1.3.6.1.4.1.3808.1.1.6.4.2.1.2	INTEGER	read-only	The Rack PDU numeric ID.
INT ePDU2PhaseConfigNearOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.4.2.1.6	INTEGER	read-write	User-defined near phase overload current warning threshold in Amps.
INT ePDU2PhaseConfigNumber	1.3.6.1.4.1.3808.1.1.6.4.2.1.3	INTEGER	read-only	The numeric phase ID.
INT ePDU2PhaseConfigOverloadRestriction	1.3.6.1.4.1.3808.1.1.6.4.2.1.4	INTEGER	read-write	This OID controls the behavior of a Switched Rack PDU phase when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding phase to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding phase to turn on if the ePDU2PhaseConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding phase to turn on if the ePDU2PhaseConfigOverloadThreshold OID is exceeded. Models that do not support this feature will respond to this OID with a value of notSupported (-1). Attempts to set this OID in these models will fail.
INT ePDU2PhaseConfigOverloadThreshold	1.3.6.1.4.1.3808.1.1.6.4.2.1.7	INTEGER	read-write	User-defined phase overload current threshold in Amps
INT ePDU2PhaseConfigPhasePeakLoadReset	1.3.6.1.4.1.3808.1.1.6.4.2.1.8	INTEGER	read-write	Setting this OID to reset (2) will cause the existing peak current value to be replaced by the present load current value. Getting this OID will do nothing and return the noOperation(1) value.
ePDU2PhaseConfigTable	1.3.6.1.4.1.3808.1.1.6.4.2		not-accessible	A table of Rack PDU phase configuration data.
ePDU2PhaseInfoEntry	1.3.6.1.4.1.3808.1.1.6.4.3.1		not-accessible	Information data from currently queried Rack PDU phase.
INT ePDU2PhaseInfoIndex	1.3.6.1.4.1.3808.1.1.6.4.3.1.1	INTEGER	read-only	The index to the Rack PDU phase properties table entry.
INT ePDU2PhaseInfoModuleIndex	1.3.6.1.4.1.3808.1.1.6.4.3.1.2	INTEGER	read-only	The Rack PDU numeric ID.
INT ePDU2PhaseInfoNumber	1.3.6.1.4.1.3808.1.1.6.4.3.1.3	INTEGER	read-only	The numeric phase ID.
ePDU2PhaseInfoTable	1.3.6.1.4.1.3808.1.1.6.4.3		not-accessible	A table of Rack PDU phase information.
GAU ePDU2PhaseStatusApparentPower	1.3.6.1.4.1.3808.1.1.6.4.4.1.8	Gauge	read-only	Indicates the load apparent power, in VoltAmps (VA), consumed on the Rack PDU phase being queried
ePDU2PhaseStatusEntry	1.3.6.1.4.1.3808.1.1.6.4.4.1		not-accessible	Status data from currently queried Rack PDU phase
INT ePDU2PhaseStatusIndex	1.3.6.1.4.1.3808.1.1.6.4.4.1.1	INTEGER	read-only	The index to the Rack PDU phase status table entry.
GAU ePDU2PhaseStatusLineToLineVoltage	1.3.6.1.4.1.3808.1.1.6.4.4.1.13	Gauge	read-only	Indicates the Line to Line Voltage, in tenths of Volts, of the Rack PDU phase being queried
GAU ePDU2PhaseStatusLoad	1.3.6.1.4.1.3808.1.1.6.4.4.1.5	Gauge	read-only	Indicates the current draw, in tenths of Amps, of the load on the Rack PDU phase being queried.
INT ePDU2PhaseStatusLoadState	1.3.6.1.4.1.3808.1.1.6.4.4.1.4	INTEGER	read-only	Indicates the present load status of the Rack PDU phase being queried.
INT ePDU2PhaseStatusModuleIndex	1.3.6.1.4.1.3808.1.1.6.4.4.1.2	INTEGER	read-only	The Rack PDU numeric ID.
INT ePDU2PhaseStatusNumber	1.3.6.1.4.1.3808.1.1.6.4.4.1.3	INTEGER	read-only	The numeric phase ID.
GAU ePDU2PhaseStatusPeakLoad	1.3.6.1.4.1.3808.1.1.6.4.4.1.10	Gauge	read-only	The peak current of the Rack PDU phase load in tenths of Amps
STR ePDU2PhaseStatusPeakLoadStartTime	1.3.6.1.4.1.3808.1.1.6.4.4.1.12	DisplayString	read-only	Indicates the date and time of the last phase peak current reset.
STR ePDU2PhaseStatusPeakLoadTimestamp	1.3.6.1.4.1.3808.1.1.6.4.4.1.11	DisplayString	read-only	Indicates the date and time the phase peak current occurred.
GAU ePDU2PhaseStatusPower	1.3.6.1.4.1.3808.1.1.6.4.4.1.7	Gauge	read-only	Indicates the load power, in watts, consumed on the Rack PDU phase being queried
GAU ePDU2PhaseStatusPowerFactor	1.3.6.1.4.1.3808.1.1.6.4.4.1.9	Gauge	read-only	Indicates the load power factor, in hundredths, of the Rack PDU phase being queried
ePDU2PhaseStatusTable	1.3.6.1.4.1.3808.1.1.6.4.4		not-accessible	A table of Rack PDU phase status data
GAU ePDU2PhaseStatusVoltage	1.3.6.1.4.1.3808.1.1.6.4.4.1.6	Gauge	read-only	Indicates the Voltage, in tenths of Volts, of the Rack PDU phase being queried
INT ePDU2PhaseTableSize	1.3.6.1.4.1.3808.1.1.6.4.1	INTEGER	read-only	A Host Rack PDU response total phase number of Rack PDUs on daisy chain. Rack PDU as a Slave can only response itself number of phase.
INT ePDU2Role	1.3.6.1.4.1.3808.1.1.6.1	INTEGER	read-only	Get this oid shows the role the PDU played on Daisy Chain Group. The PDU as a Host can access whole ePDU2 content, and the PDU be standalong or a Slave can access itself instead.
ePDU2Sensor	1.3.6.1.4.1.3808.1.1.6.7
INT ePDU2SensorTableSize	1.3.6.1.4.1.3808.1.1.6.7.1	INTEGER	read-only	ePDU2SensorTableSize
NTF ePDUBankLowLoad	1.3.6.1.4.1.3808.0.124			WARNING: A Rack PDU bank has violated the low load threshold. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
NTF ePDUBankLowLoadCleared	1.3.6.1.4.1.3808.0.125			INFORMATIONAL: The low load condition on a Rack PDU bank has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
NTF ePDUBankNearOverload	1.3.6.1.4.1.3808.0.126			WARNING: A Rack PDU bank is near an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
NTF ePDUBankNearOverloadCleared	1.3.6.1.4.1.3808.0.127			INFORMATIONAL: The near overload condition on a Rack PDU bank has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase/bank number.
NTF ePDUBankOverload	1.3.6.1.4.1.3808.0.128			SEVERE: A Rack PDU bank is in an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
NTF ePDUBankOverloadCleared	1.3.6.1.4.1.3808.0.129			INFORMATIONAL: The overload condition on a Rack PDU bank has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
NTF ePDUCancelPendingCommand	1.3.6.1.4.1.3808.0.115			INFORMATIONAL: A cancel pending command has been made on a Switched Rack PDU. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number (0 indicates all outlets). The fourth argument is the outlet name (or device name if all outlets).
NTF ePDUCommunicationEstablished	1.3.6.1.4.1.3808.0.100			INFORMATIONAL: Communication with a Rack PDU has been established. The first argument is the serial number. The second argument is the device name.
NTF ePDUCommunicationLost	1.3.6.1.4.1.3808.0.101			SEVERE: Communication with a Rack PDU has been lost. The first argument is the serial number. The second argument is the device name.
NTF ePDUComponentCommunicationEstablished	1.3.6.1.4.1.3808.0.130			INFORMATIONAL: Component communication lost has been cleared. The first argument is the serial number. The second argument is the device name.
NTF ePDUComponentCommunicationLost	1.3.6.1.4.1.3808.0.131			SEVERE: Component communication lost. The first argument is the serial number. The second argument is the device name.
NTF ePDUDelayOutletOffCommand	1.3.6.1.4.1.3808.0.113			INFORMATIONAL: An outlet on a Switched Rack PDU has been assigned to turn off. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF ePDUDelayOutletOnCommand	1.3.6.1.4.1.3808.0.112			INFORMATIONAL: An outlet on a Switched Rack PDU has been assigned to turn on. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF ePDUDelayOutletRebootCommand	1.3.6.1.4.1.3808.0.114			INFORMATIONAL: An outlet on a Switched Rack PDU has been assigned to reboot. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF ePDUDeviceConfigChange	1.3.6.1.4.1.3808.0.104			INFORMATIONAL: A device configuration change has been made on a Rack PDU. The first argument is the serial number. The second argument is the device name.
ePDUIdent	1.3.6.1.4.1.3808.1.1.3.1
STR ePDUIdentDateOfManufacture	1.3.6.1.4.1.3808.1.1.3.1.4	DisplayString	read-only	The date when the Rack PDU was manufactured in mm/dd/yyyy format. This value is set at the factory. The year 2000 will be represented by 00.
INT ePDUIdentDeviceBreakerRating	1.3.6.1.4.1.3808.1.1.3.1.11	INTEGER	read-only	Getting this OID will return rating of the circuit breakers on the device if it has any.
INT ePDUIdentDeviceDisplayOrientation	1.3.6.1.4.1.3808.1.1.3.1.14	INTEGER	read-write	Getting this OID will return the intended physical orientation of the Seven-Segment Display. displayNormal(1) indicates Normal. displayReverse(2)indicates Upside-Down. displayRotate90(3) indicates rotate 90 degree. displayRotate270(4) indicates rotate 270 degree. displayAuto(5) indicates auto-detect and rotate.
INT ePDUIdentDeviceLinetoLineVoltage	1.3.6.1.4.1.3808.1.1.3.1.15	INTEGER	read-write	Getting/Setting this OID will return/set the Line to Line Volatage. The valid range is between 0V to 440V
INT ePDUIdentDeviceNumBreakers	1.3.6.1.4.1.3808.1.1.3.1.10	INTEGER	read-only	Getting this OID will return the number of circuit breakers supported by the device. This is the same as the number of banks of outlets. 0 will be returned if the unit has no phase breakers.
INT ePDUIdentDeviceNumOutlets	1.3.6.1.4.1.3808.1.1.3.1.8	INTEGER	read-only	Getting this OID will return the number of outlets contained in the device.
INT ePDUIdentDeviceNumPhases	1.3.6.1.4.1.3808.1.1.3.1.9	INTEGER	read-only	Getting this OID will return the number of phases supported by the device.
INT ePDUIdentDeviceOrientation	1.3.6.1.4.1.3808.1.1.3.1.12	INTEGER	read-only	Getting this OID will return the intended physical orientation of the device. OrientHorizonatal(1) indicates Horizontal. OrientVertical(2) indicates Vertical.
INT ePDUIdentDeviceOutletLayout	1.3.6.1.4.1.3808.1.1.3.1.13	INTEGER	read-only	Getting this OID will return outlet layout for the device. SeqPhaseToNeutral(1) indicates outlet layout as follows: 1:1-N,2:2-N,3:3-N,4:1-N,5:2-N,... SeqPhaseToPhase(2) indicates outlet layout as follows: 1:1-2,2:2-3,3:3-1,4:1-2,5:2-3,... SeqPhToNeu21PhToPh(3) indicates outlet layout as follows: 1:1-N,2:2-N...21:3-N,22:1-2,23:2-3,24:3-1,... SeqPhToPhGrouped(4) indicates outlet layout as follows: Otlts1-8::(3-1),Otlts9-16::(2-3),Otlts17-24::(1-2).
INT ePDUIdentDeviceRating	1.3.6.1.4.1.3808.1.1.3.1.7	INTEGER	read-only	Getting this OID will return the electrical rating of the device.
STR ePDUIdentFirmwareRev	1.3.6.1.4.1.3808.1.1.3.1.3	DisplayString	read-only	An 8-byte ID string identifying the Rack PDU firmware revision. This value is set at the factory.
STR ePDUIdentHardwareRev	1.3.6.1.4.1.3808.1.1.3.1.2	DisplayString	read-only	The hardware revision of the Rack PDU. This value is set at the factory.
INT ePDUIdentIndicator	1.3.6.1.4.1.3808.1.1.3.1.16	INTEGER	read-write	PDU will perform a panel indicator test when the variable is set to testIndicators(2). It is no effective to set this value to noTestIndicators(1).
STR ePDUIdentModelNumber	1.3.6.1.4.1.3808.1.1.3.1.5	DisplayString	read-only	A 10-character string identifying the model number of the Rack PDU. This value is set at the factory.
STR ePDUIdentName	1.3.6.1.4.1.3808.1.1.3.1.1	DisplayString	read-write	The name of the Rack PDU. The maximum string size is device dependent.
STR ePDUIdentSerialNumber	1.3.6.1.4.1.3808.1.1.3.1.6	DisplayString	read-only	A 12-character string identifying the serial number of the Rack PDU. This value is set at the factory.
NTF ePDULineOvervoltage	1.3.6.1.4.1.3808.0.118			SEVERE: Utility Line Overvoltage. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
NTF ePDULineOvervoltageCleared	1.3.6.1.4.1.3808.0.119			INFORMATIONAL: Utility Line Overvoltage Cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
NTF ePDULineUndervoltage	1.3.6.1.4.1.3808.0.116			SEVERE: Utility Line Undervoltage The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
NTF ePDULineUndervoltageCleared	1.3.6.1.4.1.3808.0.117			INFORMATIONAL: Utility Line Undervoltage Cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
ePDULoad	1.3.6.1.4.1.3808.1.1.3.2
ePDULoadBankConfig	1.3.6.1.4.1.3808.1.1.3.2.4
INT ePDULoadBankConfigAlarm	1.3.6.1.4.1.3808.1.1.3.2.4.1.1.5	INTEGER	read-only	Getting this OID will return the current Bank Alarm.
ePDULoadBankConfigEntry	1.3.6.1.4.1.3808.1.1.3.2.4.1.1		not-accessible	The Rack PDU bank to configure.
INT ePDULoadBankConfigIndex	1.3.6.1.4.1.3808.1.1.3.2.4.1.1.1	INTEGER	read-only	The index to the Rack PDU bank entry.
INT ePDULoadBankConfigLowLoadThreshold	1.3.6.1.4.1.3808.1.1.3.2.4.1.1.2	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in Amps. A warning will be issued when the load is less than the threshold value. A threshold value of 0 Amps effectively disables this warning. Maximum value must be less than the value returned by the ePDULoadBankConfigNearOverloadThreshold OID.
INT ePDULoadBankConfigNearOverloadThreshold	1.3.6.1.4.1.3808.1.1.3.2.4.1.1.3	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than the value returned by the ePDULoadBankConfigLowLoadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadBankConfigOverloadThreshold OID.
INT ePDULoadBankConfigOverloadThreshold	1.3.6.1.4.1.3808.1.1.3.2.4.1.1.4	INTEGER	read-write	A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than or equal to the value returned by the ePDULoadBankConfigNearOverloadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadDevMaxBankLoad OID.
ePDULoadBankConfigTable	1.3.6.1.4.1.3808.1.1.3.2.4.1		not-accessible	Allows for configuration of each Rack PDU bank. The number of entries is contained in the ePDULoadDevNumBanks OID.
ePDULoadDevBankEntry	1.3.6.1.4.1.3808.1.1.3.2.1.6.1		not-accessible	The Rack PDU Banks Access.
INT ePDULoadDevBankIndex	1.3.6.1.4.1.3808.1.1.3.2.1.6.1.1	INTEGER	read-only	The index to the Rack PDU bank entry.
INT ePDULoadDevBankMaxLoad	1.3.6.1.4.1.3808.1.1.3.2.1.6.1.3	INTEGER	read-only	Getting this OID will return the maximum rated power that each bank of the Rack PDU can provide. It is represented in Amps.
INT ePDULoadDevBankNumber	1.3.6.1.4.1.3808.1.1.3.2.1.6.1.2	INTEGER	read-only	Getting this OID will return the bank number.
ePDULoadDevBankTable	1.3.6.1.4.1.3808.1.1.3.2.1.6		not-accessible	Allows for getting the Bank Max Load in the Rack PDU.
INT ePDULoadDevBankTableSize	1.3.6.1.4.1.3808.1.1.3.2.1.5	INTEGER	read-only	The size of the Bank Table.
ePDULoadDevice	1.3.6.1.4.1.3808.1.1.3.2.1
INT ePDULoadDevMaxBankLoad	1.3.6.1.4.1.3808.1.1.3.2.1.3	INTEGER	read-only	Getting this OID will return the maximum rated power that a bank of the Rack PDU can provide. It is represented in Amps. 0 will be returned if the device does not have any banks.
ePDULoadDevMaxOutletEntry	1.3.6.1.4.1.3808.1.1.3.2.1.8.1		not-accessible	This gives access to Max Outlet Load of an Outlet Monitored Rack PDU
INT ePDULoadDevMaxOutletLoad	1.3.6.1.4.1.3808.1.1.3.2.1.8.1.3	INTEGER	read-only	Getting this OID will return the maximum rated power that each Outlet of an Outlet Monitored Rack PDU can provide. It is represented in Amps.
ePDULoadDevMaxOutletTable	1.3.6.1.4.1.3808.1.1.3.2.1.8		not-accessible	Allows for getting the Max Outlet Load in an Outlet Monitored Rack PDU.
INT ePDULoadDevMaxOutletTableSize	1.3.6.1.4.1.3808.1.1.3.2.1.7	INTEGER	read-only	The size of the Outlet Table.
INT ePDULoadDevMaxPhaseLoad	1.3.6.1.4.1.3808.1.1.3.2.1.1	INTEGER	read-only	Getting this OID will return the maximum rated power that each phase of the Rack PDU can provide. It is represented in Amps. 0 will be returned if the unit is banked.
INT ePDULoadDevNumBanks	1.3.6.1.4.1.3808.1.1.3.2.1.4	INTEGER	read-only	The number of banks of outlets available with this Rack PDU. A bank of outlets has a unique circuit breaker for a subset of the total number of outlets on the ePDU. 0 will be returned if the unit no banks.
INT ePDULoadDevNumPhases	1.3.6.1.4.1.3808.1.1.3.2.1.2	INTEGER	read-only	The number of phases available with this Rack PDU.
INT ePDULoadDevOutletIndex	1.3.6.1.4.1.3808.1.1.3.2.1.8.1.1	INTEGER	read-only	The index to the Outlet Monitored Rack PDU Max Outlet Load entry.
INT ePDULoadDevOutletNumber	1.3.6.1.4.1.3808.1.1.3.2.1.8.1.2	INTEGER	read-only	Getting this OID will return the Outlet number.
ePDULoadPhaseConfig	1.3.6.1.4.1.3808.1.1.3.2.2
INT ePDULoadPhaseConfigAlarm	1.3.6.1.4.1.3808.1.1.3.2.2.1.1.5	INTEGER	read-only	Getting this OID will return the current Phase Alarm.
ePDULoadPhaseConfigEntry	1.3.6.1.4.1.3808.1.1.3.2.2.1.1		not-accessible	The Rack PDU phase to configure.
INT ePDULoadPhaseConfigIndex	1.3.6.1.4.1.3808.1.1.3.2.2.1.1.1	INTEGER	read-only	The index to the Rack PDU phase entry.
INT ePDULoadPhaseConfigLowLoadThreshold	1.3.6.1.4.1.3808.1.1.3.2.2.1.1.2	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in Amps. A warning will be issued when the load is less than the threshold value. A threshold value of 0 Amps effectively disables this warning. Maximum value must be less than the value returned by the ePDULoadPhaseConfigNearOverloadThreshold OID.
INT ePDULoadPhaseConfigNearOverloadThreshold	1.3.6.1.4.1.3808.1.1.3.2.2.1.1.3	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than the value returned by the ePDULoadPhaseConfigLowLoadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadPhaseConfigOverloadThreshold OID.
INT ePDULoadPhaseConfigOverloadThreshold	1.3.6.1.4.1.3808.1.1.3.2.2.1.1.4	INTEGER	read-write	A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than or equal to the value returned by the ePDULoadPhaseConfigNearOverloadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadDevMaxPhaseLoad OID.
ePDULoadPhaseConfigTable	1.3.6.1.4.1.3808.1.1.3.2.2.1		not-accessible	Allows for configuration of each Rack PDU phase. The number of entries is contained in the ePDULoadDevNumPhases OID.
ePDULoadStatus	1.3.6.1.4.1.3808.1.1.3.2.3
INT ePDULoadStatusActivePower	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.7	INTEGER	read-only	Getting this OID will return the phase/bank active power measured in watts.
INT ePDULoadStatusApparentPower	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.8	INTEGER	read-only	Getting this OID will return the phase/bank apparent power measured in VA.
INT ePDULoadStatusBankNumber	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.5	INTEGER	read-only	The bank number to which this record refers. A value of 0 will be returned if any bank is not present or if it is phase related.
INT ePDULoadStatusEnergy	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.10	INTEGER	read-only	Getting this OID will return the phase/bank apparent power measured in 0.1 kilowatt-hours.
STR ePDULoadStatusEnergyStartTime	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.11	DisplayString	read-only	Getting this OID will return the date and time of the last energy meter reset
ePDULoadStatusEntry	1.3.6.1.4.1.3808.1.1.3.2.3.1.1		not-accessible	The Rack PDU phase/bank to gather status from.
INT ePDULoadStatusIndex	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.1	INTEGER	read-only	The index to the Rack PDU phase/bank entry. All phase information will precede any bank information
GAU ePDULoadStatusLoad	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.2	Gauge	read-only	Getting this OID will return the phase/bank load measured in tenths of Amps.
INT ePDULoadStatusLoadState	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.3	INTEGER	read-only	Getting this OID will return the phase/bank load state. loadNormal(1) indicates that the phase/bank is operating properly within the ePDULoadConfigLowLoadThreshold and ePDULoadConfigNearOverloadThreshold OID values. loadLow(2) indicates that the phase/bank load has dropped below the ePDULoadConfigLowLoadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. loadNearOverload(3) indicates that the phase/bank load is greater than or equal to the ePDULoadConfigNearOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. loadOverload(4) indicates that the phase/bank load is greater than or equal to the ePDULoadConfigOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared.
INT ePDULoadStatusPhaseNumber	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.4	INTEGER	read-only	The phase number to which this record refers.
INT ePDULoadStatusPowerFactor	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.9	INTEGER	read-only	Getting this OID will return power factor of the output measured in hundredths. A value of 100 representing a unity power factor (1.00).
ePDULoadStatusTable	1.3.6.1.4.1.3808.1.1.3.2.3.1		not-accessible	Allows for getting of status of each Rack PDU phase/bank. The number of entries is calculated by adding the number of phases (ePDULoadDevNumPhases OID) and the number of banks of outlets (ePDULoadDevNumBanks) Number of entries = #phases + #banks. NOTE: If a device has phase and bank information, all phase information shall precede the bank information.
INT ePDULoadStatusVoltage	1.3.6.1.4.1.3808.1.1.3.2.3.1.1.6	INTEGER	read-only	Getting this OID will return the phase/bank voltage measured in 0.1 volts.
NTF ePDULowLoad	1.3.6.1.4.1.3808.0.106			WARNING: A Rack PDU has violated the low load threshold. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
NTF ePDULowLoadCleared	1.3.6.1.4.1.3808.0.107			INFORMATIONAL: The low load condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
NTF ePDUNearOverload	1.3.6.1.4.1.3808.0.108			WARNING: A Rack PDU is near an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
NTF ePDUNearOverloadCleared	1.3.6.1.4.1.3808.0.109			INFORMATIONAL: The near overload condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
ePDUOutlet	1.3.6.1.4.1.3808.1.1.3.3
ePDUOutletBank	1.3.6.1.4.1.3808.1.1.3.3.6
ePDUOutletBankEntry	1.3.6.1.4.1.3808.1.1.3.3.6.1.1		not-accessible	The bank to manage.
INT ePDUOutletBankIndex	1.3.6.1.4.1.3808.1.1.3.3.6.1.1.1	INTEGER	read-only	The index to the Switched Rack PDU bank entry.
INT ePDUOutletBankOverloadRestriction	1.3.6.1.4.1.3808.1.1.3.3.6.1.1.2	INTEGER	read-write	This OID controls the behavior of a Switched Rack PDU bank when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding bank to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding bank to turn on if the ePDULoadBankConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding bank to turn on if the ePDULoadBankConfigOverloadThreshold OID is exceeded.
ePDUOutletBankTable	1.3.6.1.4.1.3808.1.1.3.3.6.1		not-accessible	Allows for management of outlets on a per bank basis.
ePDUOutletConfig	1.3.6.1.4.1.3808.1.1.3.3.4
NTF ePDUOutletConfigChange	1.3.6.1.4.1.3808.0.105			INFORMATIONAL: An outlet configuration change has been made on a Switched Rack PDU. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
ePDUOutletConfigEntry	1.3.6.1.4.1.3808.1.1.3.3.4.1.1		not-accessible	The outlet to configure.
INT ePDUOutletConfigIndex	1.3.6.1.4.1.3808.1.1.3.3.4.1.1.1	INTEGER	read-only	The index to the outlet entry.
INT ePDUOutletConfigMonitoredEnergyReset	1.3.6.1.4.1.3808.1.1.3.3.4.3.1.8	INTEGER	read-write	Setting this OID to reset (2) will cause the device energy meter value to be reset to zero. Getting this oid will do nothing and return noAction (1) if the PDU support this feature, return notSupport (3) if the PDU do not support this feature.
ePDUOutletConfigMonitoredEntry	1.3.6.1.4.1.3808.1.1.3.3.4.3.1		not-accessible	This gives access to Monitored Outlet entries
INT ePDUOutletConfigMonitoredIndex	1.3.6.1.4.1.3808.1.1.3.3.4.3.1.1	INTEGER	read-only	The index to the RACK PDU Phase entry.
INT ePDUOutletConfigMonitoredLowLoadThreshold	1.3.6.1.4.1.3808.1.1.3.3.4.3.1.4	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in watts. A warning will be issued when the load is less than the threshold value. A threshold value of 0 effectively disables this warning. Maximum value must be less than the value returned by the ePDUOutletConfigMonitoredNearOverloadThreshold OID. 0 will be returned if the unit is not Outlet Monitored Rack PDU.
STR ePDUOutletConfigMonitoredName	1.3.6.1.4.1.3808.1.1.3.3.4.3.1.2	DisplayString	read-write	The name of the Monitored Outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size.
INT ePDUOutletConfigMonitoredNearOverloadThreshold	1.3.6.1.4.1.3808.1.1.3.3.4.3.1.5	INTEGER	read-write	A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in watts. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than the value returned by the ePDUOutletConfigMonitoredLowLoadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDUOutletConfigMonitoredOverloadThreshold OID. 0 will be returned if the unit is not Outlet Monitored Rack PDU.
INT ePDUOutletConfigMonitoredNumber	1.3.6.1.4.1.3808.1.1.3.3.4.3.1.3	INTEGER	read-only	The outlet number of an Outlet Monitored RACK PDU.
INT ePDUOutletConfigMonitoredOverloadThreshold	1.3.6.1.4.1.3808.1.1.3.3.4.3.1.6	INTEGER	read-write	A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in watts. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than or equal to the value returned by the ePDUOutletConfigMonitoredNearOverloadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadDevMaxOutletLoad OID. 0 will be returned if the unit is not Outlet Monitored Rack PDU.
INT ePDUOutletConfigMonitoredPeakLoadReset	1.3.6.1.4.1.3808.1.1.3.3.4.3.1.7	INTEGER	read-write	Setting this OID to reset (2) will cause the existing peak power value to be replaced by the current load power value. Getting this oid will do nothing and return noAction (1) if the PDU support this feature, return notSupport (3) if the PDU do not support this feature.
ePDUOutletConfigMonitoredTable	1.3.6.1.4.1.3808.1.1.3.3.4.3		not-accessible	Allows for getting/setting of outlet thresholds of an Outlet Monitored Rack PDU.
INT ePDUOutletConfigMonitoredTableSize	1.3.6.1.4.1.3808.1.1.3.3.4.2	INTEGER	read-only	The size of the Outlet Config Monitored Table
INT ePDUOutletConfigOutletBank	1.3.6.1.4.1.3808.1.1.3.3.4.1.1.7	INTEGER	read-only	The bank associated with this outlet.
STR ePDUOutletConfigOutletName	1.3.6.1.4.1.3808.1.1.3.3.4.1.1.2	DisplayString	read-write	The name of the outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size.
INT ePDUOutletConfigOutletPhase	1.3.6.1.4.1.3808.1.1.3.3.4.1.1.3	INTEGER	read-only	The phase/s associated with this outlet. For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), or phase3 (3) for outlets tied to a single phase. For outlets tied to two phases, this object will return phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
INT ePDUOutletConfigPowerOffTime	1.3.6.1.4.1.3808.1.1.3.3.4.1.1.5	INTEGER	read-write	The amount of time (in seconds) the outlet will delay powering off when a command that requires a turn-off delay is issued. Allowed values are: -1 - never power off. 0 - power off immediately. 1 to 7200 - power off up to 7200 seconds after being commanded.
INT ePDUOutletConfigPowerOnTime	1.3.6.1.4.1.3808.1.1.3.3.4.1.1.4	INTEGER	read-write	The amount of time (in seconds) the outlet will delay powering on at coldstart or when a command that requires a turn-on delay is issued. Allowed values are: -1 - never power on. 0 - power on immediately. 1 to 7200 - power on up to 7200 seconds after being commanded.
INT ePDUOutletConfigRebootDuration	1.3.6.1.4.1.3808.1.1.3.3.4.1.1.6	INTEGER	read-write	During a reboot sequence, power is turned off and then back on. This OID defines the amount of time to wait, in seconds, after turning the power off, at the start of the sequence, before turning power back on, at the end of the reboot sequence. Allowed range is any value between 5 and 60 seconds (1 minute).
ePDUOutletConfigTable	1.3.6.1.4.1.3808.1.1.3.3.4.1		not-accessible	Allows for configuration of individual outlets. The number of entries is contained in the ePDUOutletDevNumCntrlOutlets OID.
ePDUOutletControl	1.3.6.1.4.1.3808.1.1.3.3.3
ePDUOutletControlEntry	1.3.6.1.4.1.3808.1.1.3.3.3.1.1		not-accessible	The outlet to control.
INT ePDUOutletControlIndex	1.3.6.1.4.1.3808.1.1.3.3.3.1.1.1	INTEGER	read-only	The index to the outlet entry.
INT ePDUOutletControlOutletBank	1.3.6.1.4.1.3808.1.1.3.3.3.1.1.5	INTEGER	read-only	The bank associated with this outlet.
INT ePDUOutletControlOutletCommand	1.3.6.1.4.1.3808.1.1.3.3.3.1.1.4	INTEGER	read-write	Getting this variable will return the outlet state. If the outlet is on, the immediateOn (1) value will be returned. If the outlet is off, the immediateOff (2) value will be returned. Setting this variable to immediateOn (1) will immediately turn the outlet on. Setting this variable to immediateOff (2) will immediately turn the outlet off. Setting this variable to immediateReboot (3) will immediately reboot the outlet. Setting this variable to delayedOn (4) will turn the outlet on after the ePDUOutletConfigPowerOnTime OID time has elapsed. Setting this variable to delayedOff (5) will turn the outlet off after the ePDUOutletConfigPowerOffTime OID time has elapsed. Setting this variable to delayedReboot (6) will cause the Switched Rack PDU to perform a delayedOff command, wait the ePDUOutletConfigRebootDuration OID time, and then perform a delayedOn command. Setting this variable to cancelPendingCommand (7) will cause any pending command to this outlet to be canceled. Setting this variable to outletIdentify (8) will cause PDU LED to display the number of the outlet.
STR ePDUOutletControlOutletName	1.3.6.1.4.1.3808.1.1.3.3.3.1.1.2	DisplayString	read-only	The name of the outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size. This OID is provided for informational purposes only.
INT ePDUOutletControlOutletPhase	1.3.6.1.4.1.3808.1.1.3.3.3.1.1.3	INTEGER	read-only	The phase/s associated with this outlet. For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), or phase3 (3) for outlets tied to a single phase. For outlets tied to two phases, this object will return phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
ePDUOutletControlTable	1.3.6.1.4.1.3808.1.1.3.3.3.1		not-accessible	Allows for control of the individual outlets. The number of entries is contained in the ePDUOutletDevNumCntrlOutlets OID.
INT ePDUOutletDevColdstartDelay	1.3.6.1.4.1.3808.1.1.3.3.1.2	INTEGER	read-write	The amount of delay, in seconds, between when power is provided to the Switched Rack PDU and when the Switched Rack PDU provides basic master power to the outlets. Allowed values are: -1 - never apply power automatically. 0 - apply power immediately. 1 to 300 - delay up to 300 seconds (5 minutes).
INT ePDUOutletDevColdstartState	1.3.6.1.4.1.3808.1.1.3.3.1.6	INTEGER	read-write	The ePDU outlet state after coldstart. Allowed values are: 1 - all outlets on after coldstart. 2 - outlet status same as previous state.
INT ePDUOutletDevCommand	1.3.6.1.4.1.3808.1.1.3.3.1.1	INTEGER	read-write	Setting this OID to immediateAllOn (2) will turn all outlets on immediately. Setting this OID to immediateAllOff (3) will turn all outlets off immediately. Setting this OID to immediateAllReboot (4) will reboot all outlets immediately. Setting this OID to delayedAllOn (5) will turn all outlets on as defined by each outlet's ePDUOutletConfigPowerOnTime OID value. Setting this OID to delayedAllOff (6) will turn all outlets off as defined by each outlet's ePDUOutletConfigPowerOffTime OID value. Setting this OID to delayedAllReboot (7) will cause a delayedAllOff command to be performed. Once all outlets are off, the Switched Rack PDU will then delay the largest ePDUOutletConfigRebootDuration OID time, and then perform a delayedAllOn command. Setting this OID to cancelAllPendingCommands (8) will cause all pending commands on the Switched Rack PDU to be canceled. Getting this OID will return the noCommandAll (1) value.
ePDUOutletDevice	1.3.6.1.4.1.3808.1.1.3.3.1
INT ePDUOutletDevMonitoredOutlets	1.3.6.1.4.1.3808.1.1.3.3.1.5	INTEGER	read-only	The total number of monitored outlets on this Rack PDU.
INT ePDUOutletDevNumCntrlOutlets	1.3.6.1.4.1.3808.1.1.3.3.1.3	INTEGER	read-only	The number of controlled outlets on this Switched Rack PDU.
INT ePDUOutletDevNumTotalOutlets	1.3.6.1.4.1.3808.1.1.3.3.1.4	INTEGER	read-only	The total number of outlets on this Rack PDU.
NTF ePDUOutletLowLoad	1.3.6.1.4.1.3808.0.132			WARNING: A Rack PDU has violated the outlet low load threshold. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
NTF ePDUOutletLowLoadCleared	1.3.6.1.4.1.3808.0.133			INFORMATIONAL: The outlet low load condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
NTF ePDUOutletNearOverload	1.3.6.1.4.1.3808.0.134			WARNING: A Rack PDU is near an outlet overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
NTF ePDUOutletNearOverloadCleared	1.3.6.1.4.1.3808.0.135			INFORMATIONAL: The outlet near overload condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
NTF ePDUOutletOff	1.3.6.1.4.1.3808.0.103			INFORMATIONAL: An outlet on a Switched Rack PDU has turned off. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF ePDUOutletOn	1.3.6.1.4.1.3808.0.102			INFORMATIONAL: An outlet on a Switched Rack PDU has turned on. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
NTF ePDUOutletOverload	1.3.6.1.4.1.3808.0.136			SEVERE: A Rack PDU is in an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
NTF ePDUOutletOverloadCleared	1.3.6.1.4.1.3808.0.137			INFORMATIONAL: The outlet overload condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
ePDUOutletPhase	1.3.6.1.4.1.3808.1.1.3.3.2
ePDUOutletPhaseEntry	1.3.6.1.4.1.3808.1.1.3.3.2.1.1		not-accessible	The phase to manage.
INT ePDUOutletPhaseIndex	1.3.6.1.4.1.3808.1.1.3.3.2.1.1.1	INTEGER	read-only	The index to the Switched Rack PDU phase entry.
INT ePDUOutletPhaseOverloadRestriction	1.3.6.1.4.1.3808.1.1.3.3.2.1.1.2	INTEGER	read-write	This OID controls the behavior of a Switched Rack PDU phase when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding phase to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigOverloadThreshold OID is exceeded.
ePDUOutletPhaseTable	1.3.6.1.4.1.3808.1.1.3.3.2.1		not-accessible	Allows for management of outlets on a per phase basis.
ePDUOutletStatus	1.3.6.1.4.1.3808.1.1.3.3.5
GAU ePDUOutletStatusActivePower	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.8	Gauge	read-only	Getting this OID will return the measured Outlet load for an Outlet Monitored Rack PDU in watts
INT ePDUOutletStatusAlarm	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.9	INTEGER	read-only	Getting this OID will return the current outlet alarm
INT ePDUOutletStatusCommandPending	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.5	INTEGER	read-only	Getting this variable will return the command pending state of the outlet. If a command is pending on the outlet, the outletStatusCommandPending (1) value will be returned. If there is not a command pending on the outlet, the outletStatusNoCommandPending (2) will be returned.
GAU ePDUOutletStatusEnergy	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.13	Gauge	read-only	Energy meter measuring Rack PDU load energy consumption in tenths of kilowatt-hours. This value can be reset by setting the oid ePDUOutletConfigMonitoredEnergyReset to reset (2)
STR ePDUOutletStatusEnergyStartTime	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.14	DisplayString	read-only	Indicates the date and time of the last device energy meter reset
ePDUOutletStatusEntry	1.3.6.1.4.1.3808.1.1.3.3.5.1.1		not-accessible	The outlet to gather status from.
INT ePDUOutletStatusIndex	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.1	INTEGER	read-only	The index to the outlet entry.
GAU ePDUOutletStatusLoad	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.7	Gauge	read-only	Getting this OID will return the measured Outlet load for an Outlet Monitored Rack PDU in tenths of Amps.
INT ePDUOutletStatusOutletBank	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.6	INTEGER	read-only	The bank associated with this outlet.
STR ePDUOutletStatusOutletName	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.2	DisplayString	read-only	The name of the outlet. The maximum string size is device dependent. This OID is provided for informational purposes only.
INT ePDUOutletStatusOutletPhase	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.3	INTEGER	read-only	The phase/s associated with this outlet. For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), or phase3 (3) for outlets tied to a single phase. For outlets tied to two phases, this object will return phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
INT ePDUOutletStatusOutletState	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.4	INTEGER	read-only	Getting this variable will return the outlet state. If the outlet is on, the outletStatusOn (1) value will be returned. If the outlet is off, the outletStatusOff (2) value will be returned.
GAU ePDUOutletStatusPeakPower	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.10	Gauge	read-only	The peak power consumption of the Rack PDU load in watts. This value can be reset by setting the oid ePDUOutletConfigMonitoredPeakLoadReset to reset (2)
STR ePDUOutletStatusPeakPowerStart	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.12	DisplayString	read-only	Get this oid shows the date and time that peak power consumption started
STR ePDUOutletStatusPeakPowerTime	1.3.6.1.4.1.3808.1.1.3.3.5.1.1.11	DisplayString	read-only	Get this oid shows the date and time that peak power consumption occurred
ePDUOutletStatusTable	1.3.6.1.4.1.3808.1.1.3.3.5.1		not-accessible	Allows for getting of status of individual outlets. The number of entries is contained in the ePDUOutletDevNumCntrlOutlets OID.
NTF ePDUOverload	1.3.6.1.4.1.3808.0.110			SEVERE: A Rack PDU is in an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
NTF ePDUOverloadCleared	1.3.6.1.4.1.3808.0.111			INFORMATIONAL: The overload condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
ePDUPowerSupply	1.3.6.1.4.1.3808.1.1.3.4
NTF ePDUPowerSupply1Fail	1.3.6.1.4.1.3808.0.120			SEVERE: Power Supply 1 on Rack PDU is in FAIL state. The first argument is the serial number. The second argument is the device name.
NTF ePDUPowerSupply1Ok	1.3.6.1.4.1.3808.0.121			INFORMATIONAL: Power Supply 1 on Rack PDU is operating normally. The first argument is the serial number. The second argument is the device name.
INT ePDUPowerSupply1Status	1.3.6.1.4.1.3808.1.1.3.4.1.1	INTEGER	read-only	Getting this OID will return powerSupply1Ok(1) if power supply 1 is functioning normally. If not functioning normally, this OID will return powerSupply1Failed(2).
NTF ePDUPowerSupply2Fail	1.3.6.1.4.1.3808.0.122			SEVERE: Power Supply 2 on Rack PDU is in FAIL state. The first argument is the serial number. The second argument is the device name.
NTF ePDUPowerSupply2Ok	1.3.6.1.4.1.3808.0.123			INFORMATIONAL: Power Supply 2 on Rack PDU is operating normally. The first argument is the serial number. The second argument is the device name.
INT ePDUPowerSupply2Status	1.3.6.1.4.1.3808.1.1.3.4.1.2	INTEGER	read-only	Getting this OID will return powerSupply2Ok(1) if power supply 2 is functioning normally. If not functioning normally, this OID will return powerSupply2Failed(2). Metered Rack PDUs do not have a redundant powersupply.
INT ePDUPowerSupplyAlarm	1.3.6.1.4.1.3808.1.1.3.4.1.3	INTEGER	read-only	Getting this OID will return powerSupply Alarm
ePDUPowerSupplyDevice	1.3.6.1.4.1.3808.1.1.3.4.1
ePDUStatus	1.3.6.1.4.1.3808.1.1.3.5
ePDUStatusBankEntry	1.3.6.1.4.1.3808.1.1.3.5.2.1		not-accessible	This gives access to Bank entries
INT ePDUStatusBankIndex	1.3.6.1.4.1.3808.1.1.3.5.2.1.1	INTEGER	read-only	The index to the RACK PDU Bank entry.
INT ePDUStatusBankNumber	1.3.6.1.4.1.3808.1.1.3.5.2.1.2	INTEGER	read-only	Getting this OID will return the bank number.
INT ePDUStatusBankState	1.3.6.1.4.1.3808.1.1.3.5.2.1.3	INTEGER	read-only	Getting this OID will return the bank load state. bankLoadNormal(1) indicates that the bank is operating properly within the ePDULoadBankConfigLowLoadThreshold and ePDULoadBankConfigNearOverloadThreshold OID values. bankLoadLow(2) indicates that the bank load has dropped below the ePDULoadBankConfigLowLoadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. bankLoadNearOverload(3) indicates that the bank load is greater than or equal to the ePDULoadBankConfigNearOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. bankLoadOverload(4) indicates that the bank load is greater than or equal to the ePDULoadBankConfigOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared.
ePDUStatusBankTable	1.3.6.1.4.1.3808.1.1.3.5.2		not-accessible	Allows for getting of status of each Rack PDU Bank
INT ePDUStatusBankTableSize	1.3.6.1.4.1.3808.1.1.3.5.1	INTEGER	read-only	The size of the Status Bank Table
INT ePDUStatusInputFrequency	1.3.6.1.4.1.3808.1.1.3.5.8	INTEGER	read-only	The input frequency in 0.1 Hertz.
INT ePDUStatusInputVoltage	1.3.6.1.4.1.3808.1.1.3.5.7	INTEGER	read-only	The input voltage in 0.1 Volt.
ePDUStatusOutletEntry	1.3.6.1.4.1.3808.1.1.3.5.6.1		not-accessible	This gives access to Outlet entries
INT ePDUStatusOutletIndex	1.3.6.1.4.1.3808.1.1.3.5.6.1.1	INTEGER	read-only	The index to the RACK PDU Outlet entry.
INT ePDUStatusOutletNumber	1.3.6.1.4.1.3808.1.1.3.5.6.1.2	INTEGER	read-only	Getting this OID will return the Outlet number.
INT ePDUStatusOutletState	1.3.6.1.4.1.3808.1.1.3.5.6.1.3	INTEGER	read-only	Getting this OID will return the Outlet load state. outletLoadNormal(1) indicates that the Outlet is operating properly within the ePDUOutletConfigMonitoredLowLoadThreshold and ePDUOutletConfigMonitoredNearOverloadThreshold OID values. outletLoadLow(2) indicates that the Outlet load has dropped below the ePDUOutletConfigMonitoredLowLoadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. outletLoadNearOverload(3) indicates that the Outlet load is greater than or equal to the ePDUOutletConfigMonitoredNearOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. outletLoadOverload(4) indicates that the Outlet load is greater than or equal to the ePDUOutletConfigMonitoredOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared.
ePDUStatusOutletTable	1.3.6.1.4.1.3808.1.1.3.5.6		not-accessible	Allows for getting of status of each Outlet of an Outlet Monitored Rack PDU.
INT ePDUStatusOutletTableSize	1.3.6.1.4.1.3808.1.1.3.5.5	INTEGER	read-only	The size of the Status Outlet Table
ePDUStatusPhaseEntry	1.3.6.1.4.1.3808.1.1.3.5.4.1		not-accessible	This gives access to Phase entries
INT ePDUStatusPhaseIndex	1.3.6.1.4.1.3808.1.1.3.5.4.1.1	INTEGER	read-only	The index to the RACK PDU Phase entry.
INT ePDUStatusPhaseNumber	1.3.6.1.4.1.3808.1.1.3.5.4.1.2	INTEGER	read-only	Getting this OID will return the phase number.
INT ePDUStatusPhaseState	1.3.6.1.4.1.3808.1.1.3.5.4.1.3	INTEGER	read-only	Getting this OID will return the Phase load state. phaseLoadNormal(1) indicates that the Phase is operating properly within the ePDULoadPhaseConfigLowLoadThreshold and ePDULoadPhaseConfigNearOverloadThreshold OID values. phaseLoadLow(2) indicates that the Phase load has dropped below the ePDULoadPhaseConfigLowLoadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. phaseLoadNearOverload(3) indicates that the Phase load is greater than or equal to the ePDULoadPhaseConfigNearOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. phaseLoadOverload(4) indicates that the Phase load is greater than or equal to the ePDULoadPhaseConfigOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared.
ePDUStatusPhaseTable	1.3.6.1.4.1.3808.1.1.3.5.4		not-accessible	Allows for getting of status of each Rack PDU Phase
INT ePDUStatusPhaseTableSize	1.3.6.1.4.1.3808.1.1.3.5.3	INTEGER	read-only	The size of the Status Phase Table
eswitch	1.3.6.1.4.1.3808.1.1.2
INT eSwitchActOutlet	1.3.6.1.4.1.3808.1.1.2.2.3.1.2	INTEGER	read-write	The action outlets to be controlled.
INT eSwitchActType	1.3.6.1.4.1.3808.1.1.2.2.3.1.3	INTEGER	read-write	The on/off type of the action outlets. 1 for duration off, 2 for duration on, 3 for immediately off, 4 for immediately on, and 5 for reboot.
eSwitchBase	1.3.6.1.4.1.3808.1.1.2.2
eSwitchBaseCtrEntry	1.3.6.1.4.1.3808.1.1.2.2.3.1		not-accessible	An entry control information of individual switches.
eSwitchBaseCtrTable	1.3.6.1.4.1.3808.1.1.2.2.3		not-accessible	A list of switch control parameters. The number of entries is given by the value of eSwitchNumber.
eSwitchBaseEntry	1.3.6.1.4.1.3808.1.1.2.2.2.1		not-accessible	An entry information of the individual switch.
eSwitchBaseTable	1.3.6.1.4.1.3808.1.1.2.2.2		not-accessible	A list of switch information. The number of entries is given by the value of eSwitchNumber.
INT eSwitchCtrID	1.3.6.1.4.1.3808.1.1.2.2.3.1.1	INTEGER	read-write	Select the switch ID to be controlled.
INT eSwitchID	1.3.6.1.4.1.3808.1.1.2.2.2.1.1	INTEGER	read-only	The power switch ID number.
eSwitchIdent	1.3.6.1.4.1.3808.1.1.2.1
STR eSwitchIdentDateOfManufacture	1.3.6.1.4.1.3808.1.1.2.1.3	DisplayString	read-only	The manufacture date in mm/dd/yy format.
STR eSwitchIdentFirmwareRev	1.3.6.1.4.1.3808.1.1.2.1.2	DisplayString	read-only	The firmware revision set at the factory.
STR eSwitchIdentHardwareRev	1.3.6.1.4.1.3808.1.1.2.1.1	DisplayString	read-only	The hardware revision set at the factory.
STR eSwitchIdentModelName	1.3.6.1.4.1.3808.1.1.2.1.4	DisplayString	read-only	The model name set at the factory. This value need to consist with safty report.
INT eSwitchNumber	1.3.6.1.4.1.3808.1.1.2.2.1	INTEGER	read-only	The numbers of switch have been attached to the system.
INT eSwitchOutletNum	1.3.6.1.4.1.3808.1.1.2.2.2.1.2	INTEGER	read-only	The number of outlets provided in the switch.
STR eSwitchOutletState	1.3.6.1.4.1.3808.1.1.2.2.2.1.3	DisplayString	read-only	Getting this OID will reply the status of all outlets in the switch. '0' for outlet off, '1' for outlet on. The index from left to right is outlet#8, #7, #6, #5, #4, #3, #2, #1. For Example: If the string is '01011010', it means the outlets status are the following: outlet #8 is off, outlet #7 is on, outlet #6 is off, outlet #5 is on, outlet #4 is on, outlet #3 is off, outlet #2 is on, outlet #1 is off.
NTF failAuthViaConsole	1.3.6.1.4.1.3808.0.63			WARNING: Login authorization failure via Console.
NTF failAuthViaHTTP	1.3.6.1.4.1.3808.0.61			WARNING: Login authorization failure via HTTP.
hardware	1.3.6.1.4.1.3808.1.1
NTF lowBattery	1.3.6.1.4.1.3808.0.7			SEVERE: The UPS battery capacity is low than threshold, soon to be exhausted.
mconfig	1.3.6.1.4.1.3808.2.1
mconfigClock	1.3.6.1.4.1.3808.2.1.5
STR mconfigClockDate	1.3.6.1.4.1.3808.2.1.5.1	DisplayString	read-write	The current date in the mm/dd/yyyy format. Example: 01/01/2000.
STR mconfigClockTime	1.3.6.1.4.1.3808.2.1.5.2	DisplayString	read-write	The current time in the hh:mm:ss 24H format.
INT mconfigDHCPEnabled	1.3.6.1.4.1.3808.2.1.3	INTEGER	read-write	The system will automatically obtain its IP from a DHCP server if yes, and none if no.
IP mconfigMyAddr	1.3.6.1.4.1.3808.2.1.4	IpAddress	read-only	The system IP address.
INT mconfigNumTrapAccepters	1.3.6.1.4.1.3808.2.1.1	INTEGER	read-only	The number of receivers to send traps to.
mconfigTrapAccepterEntry	1.3.6.1.4.1.3808.2.1.2.1		not-accessible	The receivers to send traps to.
mconfigTrapAccepterTable	1.3.6.1.4.1.3808.2.1.2		not-accessible	A list of receivers to send traps to. The numbers of entries are given by the value of mconfigNumTrapAccepters.
mcontrol	1.3.6.1.4.1.3808.2.3
INT mcontrolReset	1.3.6.1.4.1.3808.2.3.2	INTEGER	read-write	Setting this OID to resetCurrentSystem (2) will reset the current system. Setting this OID to resetCurrentAgent (3) will reset the current agent. Setting this OID to resetCurrentSystemAndAgenta (4) will reset the current system and the current agent.
INT mcontrolRestart	1.3.6.1.4.1.3808.2.3.1	INTEGER	read-write	Setting this OID to restartCurrentSystem (2) will restart the current system. Setting this OID to restartCurrentAgent (3) will restart the current agent. Setting this OID to restartCurrentSystemAnd Agent (4) will restart the current the current system and agent.
mtrapinfo	1.3.6.1.4.1.3808.2.2
INT mtrapinfoBmEventId	1.3.6.1.4.1.3808.2.2.6	INTEGER	read-only	Allow CPS traps with an integer argument for providing detail information about Battery Manager specific event identifier. Not being defined in the MIB, only reply 0. Known Specific Event ID: Battery Manager 0 - not used 1 - Alarm: The battery manager system fault. 2 - Info: Device configuration changed. 3 - Alarm: Probe configuration mismatched. 4 - Info: Probe configuration matched. 5 - Alarm: Communication with battery manager has been lost. 6 - Info: Communication with battery manager has been restored. 7 - Alarm: Communication with LCD has been lost. 8 - Info: Communication with LCD has been restored. 9 - Warning: Enter battery equalization active mode. 10- Warning: Leave battery equalization active mode. 11- Alarm: Battery equalizing has failed. 12- Info: Battery equalizing succeed. Known Specific Event ID: Battery Probes 101 - Alarm: Low battery voltage. 102 - Alarm: High battery voltage. 103 - Info: Battery voltage event has cleared. 104 - Alarm: Low battery temperature. 105 - Alarm: High battery temperature. 106 - Info: Battery temperature event has cleared. 107 - Alarm: Critical low battery resistance. 108 - Alarm: Critical high battery resistance. 109 - Warning: Low battery resistance. 110 - Warning: high battery resistance. 111 - Info: Battery resistance event has cleared. 112 - Alarm: Battery resistance health has crossed alarm threshold. 113 - Warning: Battery resistance health has crossed warning threshold. 114 - Info: Battery resistance health has returned to Normal.
GAU mtrapinfoGauge	1.3.6.1.4.1.3808.2.2.4	Gauge	read-only	Allow CPS traps with an Gauge argument for providing detail information. Not being defined in the MIB, only reply 0.
INT mtrapinfoInteger	1.3.6.1.4.1.3808.2.2.1	INTEGER	read-only	Allow CPS traps with an integer argument for providing detail information. Not being defined in the MIB, only reply 0.
IP mtrapinfoIpAddress	1.3.6.1.4.1.3808.2.2.2	IpAddress	read-only	Allow CPS traps with an IP address argument for providing detail information. Not being defined in the MIB, only reply 0.0.0.0.
STR mtrapinfoString	1.3.6.1.4.1.3808.2.2.3	DisplayString	read-only	Allow CPS traps with an octet string argument for providing detail information. Not being defined in the MIB, only reply a NULL string.
TIK mtrapinfoTimeTicks	1.3.6.1.4.1.3808.2.2.5	TimeTicks	read-only	Allow CPS traps with an TimeTicks argument for providing detail information. Not being defined in the MIB, only reply 0.
NTF nclBankOff	1.3.6.1.4.1.3808.0.32			INFORMATIONAL: Non-Critical bank has been turned off.
NTF nclBankOn	1.3.6.1.4.1.3808.0.31			INFORMATIONAL: Non-Critical bank has been turned on.
NTF nclBankStartScheduleOff	1.3.6.1.4.1.3808.0.36			INFORMATION: Non-Critial bank has started its schedule off sequence.
NTF outletUserLoginInfo	1.3.6.1.4.1.3808.0.73			Information: Outlet User login.
NTF outletUserLogoutInfo	1.3.6.1.4.1.3808.0.74			Information: Outlet User logout.
NTF passwordChange	1.3.6.1.4.1.3808.0.62			INFORMATION: The password has been changed.
NTF pduBankAlarm	1.3.6.1.4.1.3808.0.407			Alarm: A PDU bank alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the bank table index. The foutrh argument is the bank number.
NTF pduBankAlarmClear	1.3.6.1.4.1.3808.0.408			INFORMATIONAL: A PDU bank alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the bank table index. The foutrh argument is the bank number.
NTF pduBankEvent	1.3.6.1.4.1.3808.0.406			INFORMATIONAL: A PDU bank event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the bank table index. The foutrh argument is the bank number.
NTF pduDaisyChainAlarm	1.3.6.1.4.1.3808.0.416			Alarm: A PDU daisy-chain alarm has been detected. The first argument is the host serial number. The second argument is the host device name. The third argument is the alarm device table index. The foutrh argument is the alarm device serial number. The fifth argument is the alarm device name.
NTF pduDaisyChainAlarmClear	1.3.6.1.4.1.3808.0.417			INFORMATIONAL: A PDU daisy-chain alarm has been cleared. The first argument is the host serial number. The second argument is the host device name. The third argument is the alarm device table index. The foutrh argument is the alarm deice serial number. The fifth argument is the alarm device name.
NTF pduDaisyChainEvent	1.3.6.1.4.1.3808.0.415			INFORMATIONAL: A PDU daisy-chain event has been happened. The first argument is the host serial number. The second argument is the host device name. The third argument is the event device table index. The foutrh argument is the event device serial number. The fifth argument is the event device name.
NTF pduDeviceAlarm	1.3.6.1.4.1.3808.0.401			Alarm: A PDU device alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the device table index.
NTF pduDeviceAlarmClear	1.3.6.1.4.1.3808.0.402			INFORMATIONAL: A PDU device alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the device table index.
NTF pduDeviceEvent	1.3.6.1.4.1.3808.0.400			INFORMATIONAL: A PDU device event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the device table index.
NTF pduOutletMeteredAlarm	1.3.6.1.4.1.3808.0.413			Alarm: A PDU metered outlet alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
NTF pduOutletMeteredAlarmClear	1.3.6.1.4.1.3808.0.414			INFORMATIONAL: A PDU metered outlet alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
NTF pduOutletMeteredEvent	1.3.6.1.4.1.3808.0.412			INFORMATIONAL: A PDU metered outlet event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
NTF pduOutletSwitchedAlarm	1.3.6.1.4.1.3808.0.410			Alarm: A PDU switched outlet alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
NTF pduOutletSwitchedAlarmClear	1.3.6.1.4.1.3808.0.411			INFORMATIONAL: A PDU switched outlet alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
NTF pduOutletSwitchedEvent	1.3.6.1.4.1.3808.0.409			INFORMATIONAL: A PDU switched outlet event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
NTF pduPhaseAlarm	1.3.6.1.4.1.3808.0.404			Alarm: A PDU phase alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the phase table index. The foutrh argument is the phase number.
NTF pduPhaseAlarmClear	1.3.6.1.4.1.3808.0.405			INFORMATIONAL: A PDU phase alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase table index. The foutrh argument is the phase number.
NTF pduPhaseEvent	1.3.6.1.4.1.3808.0.403			INFORMATIONAL: A PDU phase event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the phase table index. The foutrh argument is the phase number.
NTF powerRestored	1.3.6.1.4.1.3808.0.9			INFORMATIONAL: Utility power restored, return from backup mode.
products	1.3.6.1.4.1.3808.1
NTF returnFromChargerFailure	1.3.6.1.4.1.3808.0.24			INFORMATIONAL: The charger returned from a failure condition.
NTF returnFromDischarged	1.3.6.1.4.1.3808.0.20			INFORMATIONAL: The UPS runtime estimation completed.
NTF returnFromLowBattery	1.3.6.1.4.1.3808.0.11			INFORMATIONAL: The UPS has returned from a low battery condition.
NTF returnFromOverLoad	1.3.6.1.4.1.3808.0.19			INFORMATIONAL: The UPS has returned from an overload condition.
NTF returnFromOverTemp	1.3.6.1.4.1.3808.0.17			INFORMATIONAL: The UPS over temperature condition cleared.
INT severityDegree	1.3.6.1.4.1.3808.2.1.2.1.4	INTEGER	read-only	The trap receiver severity level. Traps are marked in severity level as informational(1), warning(2), severe(3). Only send the traps of equal or greater severity than this value to the receiver.
NTF testEvent	1.3.6.1.4.1.3808.0.72			Information: Test Event.
INT trapIndex	1.3.6.1.4.1.3808.2.1.2.1.1	INTEGER	not-accessible	The trap receiver entry index.
ups	1.3.6.1.4.1.3808.1.1.1
upsAdvanceBattery	1.3.6.1.4.1.3808.1.1.1.2.2
GAU upsAdvanceBatteryCapacity	1.3.6.1.4.1.3808.1.1.1.2.2.1	Gauge	read-only	The battery capacity expressed in percentage.
INT upsAdvanceBatteryCurrent	1.3.6.1.4.1.3808.1.1.1.2.2.7	INTEGER	read-only	The battery current expressed in percentage.
INT upsAdvanceBatteryFullChargeVoltage	1.3.6.1.4.1.3808.1.1.1.2.2.6	INTEGER	read-only	The battery charged voltage expressed in 1/10 VDC.
INT upsAdvanceBatteryLife	1.3.6.1.4.1.3808.1.1.1.2.2.9	INTEGER	read-only	The battery life expressed in 1/100 percentage.
INT upsAdvanceBatteryReplaceIndicator	1.3.6.1.4.1.3808.1.1.1.2.2.5	INTEGER	read-only	This value indicates if UPS batteries need to be replaced.
TIK upsAdvanceBatteryRunTimeRemaining	1.3.6.1.4.1.3808.1.1.1.2.2.4	TimeTicks	read-only	The UPS battery remaining run time.
GAU upsAdvanceBatteryTemperature	1.3.6.1.4.1.3808.1.1.1.2.2.3	Gauge	read-only	The UPS battery temperature expressed in Celsius.
INT upsAdvanceBatteryVoltage	1.3.6.1.4.1.3808.1.1.1.2.2.2	INTEGER	read-only	The battery voltage expressed in 1/10 VDC.
INT upsAdvanceBatteryVoltageRating	1.3.6.1.4.1.3808.1.1.1.2.2.8	INTEGER	read-only	The DC voltage rating of the battery set.
upsAdvanceConfig	1.3.6.1.4.1.3808.1.1.1.5.2
INT upsAdvanceConfigAlarm	1.3.6.1.4.1.3808.1.1.1.5.2.4	INTEGER	read-write	This value is set to handle audible alarms when power failure.
TIK upsAdvanceConfigAlarmTimer	1.3.6.1.4.1.3808.1.1.1.5.2.5	TimeTicks	read-write	The time after power failure at which the UPS begins giving audible alarms. This timer is effective only if the value of upsAdvanceConfigAlarm is timed(1). Accepted values are between 0 to 60 seconds. If a value other than a supported value is set, the value will not be accepted.
INT upsAdvanceConfigAutoRestore	1.3.6.1.4.1.3808.1.1.1.5.2.13	INTEGER	read-write	When this option is enabled, the UPS will restore output immediately when the utility power restores.When this option is disabled, the UPS will not restore output at that moment and users have to turn it on manually at a later time.
INT upsAdvanceConfigColdStart	1.3.6.1.4.1.3808.1.1.1.5.2.15	INTEGER	read-write	Set the ability of the UPS can start in the absence of input power.When this option is enabled the UPS can be turned on without having input power.
INT upsAdvanceConfigDeepDischargeProtection	1.3.6.1.4.1.3808.1.1.1.5.2.16	INTEGER	read-write	When the UPS is on Battery Mode with 0% load and the status remains for the time configured,the RMCARD will enforce the UPS to Sleep Mode and the output will be turned off. The possible values are 0, 20, 40, and 60 minutes. If a value other than a possible value is set, it will not be accepted.
INT upsAdvanceConfigHighTransferVolt	1.3.6.1.4.1.3808.1.1.1.5.2.2	INTEGER	read-write	Adjust the high transfer vloltage in VAC. The high transfer vloltage will become the UPS default value subtracts this value. The allowed values depend on the output: 100-127 volt system allow settings of 0-15. 208-240 volt system allow settings of 0-30. If the adjustable value is over the allowed values, it will not be accepted.
TIK upsAdvanceConfigLowBatteryRunTime	1.3.6.1.4.1.3808.1.1.1.5.2.8	TimeTicks	read-write	The desired run time, in seconds, UPS will enter in a low battery sequence. The possible values are 120, 300, 420, 600. If a value other than a supported value is set, the value will not be accepted.
INT upsAdvanceConfigLowBatteryThreshold	1.3.6.1.4.1.3808.1.1.1.5.2.18	INTEGER	read-write	When the UPS supplies battery power and the remaining capacity is lower than this threshold, the UPS will sound an alarm. The value expressed in percentage.
INT upsAdvanceConfigLowTransferVolt	1.3.6.1.4.1.3808.1.1.1.5.2.3	INTEGER	read-write	Adjust the low transfer vloltage in VAC. The low transfer vloltage will become the UPS default value adds this value. The allowed values depend on the output: 100-127 volt system allow settings of 0-15. 208-240 volt system allow settings of 0-30. If the adjustable value is over the allowed values, it will not be accepted.
INT upsAdvanceConfigMinReturnCapacity	1.3.6.1.4.1.3808.1.1.1.5.2.6	INTEGER	read-write	The minimum battery capacity that UPS will return from a low battery shutdown condition. The possible values are between 0 to 40. If a value other than a supported value is set, the value will not be accepted.
INT upsAdvanceConfigOutputVoltage	1.3.6.1.4.1.3808.1.1.1.5.2.1	INTEGER	read-write	The standard UPS output voltage in VAC. The possible values are 100, 110, 120, 127, 208, 220, 230, and 240. If a value other than a possible value is set, it will not be accepted.
INT upsAdvanceConfigRechargedCapacity	1.3.6.1.4.1.3808.1.1.1.5.2.14	INTEGER	read-write	When the utility power restores, the UPS will start to recharge until the specified battery capacity in percentage is met before restoring output power. The possible values are 0, 15, 30, 45, 60, 75, and 90. If a value other than a possible value is set, it will not be accepted.
TIK upsAdvanceConfigReturnDelay	1.3.6.1.4.1.3808.1.1.1.5.2.9	TimeTicks	read-write	The delay time the UPS will turn on after power recovery. The value is also used in a 'reboot' or 'wake up' sequence. The possible values are 0 to 600 seconds. If a value other than a supported value is set, the value will not be accepted.
INT upsAdvanceConfigSensitivity	1.3.6.1.4.1.3808.1.1.1.5.2.7	INTEGER	read-write	The sensitivity of the UPS to power failure detection.
INT upsAdvanceConfigSetEEPROMDefaults	1.3.6.1.4.1.3808.1.1.1.5.2.12	INTEGER	read-write	Reset the UPS EEPROM parameters to default values.
TIK upsAdvanceConfigShutoffDelay	1.3.6.1.4.1.3808.1.1.1.5.2.10	TimeTicks	read-write	The delay time the UPS will remain on after receiving a turn off command. The possible values are between 60 to 5940 seconds. If a value other than a supported value is set, the value will not be accepted.
INT upsAdvanceConfigSleepAfterAllClientShut	1.3.6.1.4.1.3808.1.1.1.5.2.17	INTEGER	read-write	If this option is enabled, UPS will enter sleep mode after utility power failed and remaining MSDT+2 minutes.More information about MSDT please reference to help page of UPS - > PowerPanel List.
TIK upsAdvanceConfigSleepDelay	1.3.6.1.4.1.3808.1.1.1.5.2.11	TimeTicks	read-write	The delay time the UPS will enter sleep mode after receiving a sleep command. WThe possible values are between 60 to 5940 seconds. If a value other than a supported value is set, the value will not be accepted.
upsAdvanceControl	1.3.6.1.4.1.3808.1.1.1.6.2
INT upsAdvanceControlFlashAndBeep	1.3.6.1.4.1.3808.1.1.1.6.2.5	INTEGER	read-write	UPS will beep and simultaneously turn on the panel lights when the variable is set to flashAndBeep(2). It is no effective to set this value to noSimulatePowerFailure(1).
INT upsAdvanceControlRebootUps	1.3.6.1.4.1.3808.1.1.1.6.2.2	INTEGER	read-write	UPS will shutdown and turn back on when the variable is set to rebootUps(2). It is no effective to set this value to noRebootUps(1).
INT upsAdvanceControlSimulatePowerFail	1.3.6.1.4.1.3808.1.1.1.6.2.4	INTEGER	read-write	UPS will transfer to backup mode when the variable is set to simulatePowerFailure(2). It is no effective to set this value to noFlashAndBeep(1).
INT upsAdvanceControlTurnOnUPS	1.3.6.1.4.1.3808.1.1.1.6.2.6	INTEGER	read-write	UPS will turned on immediately when the variable is set to turnOnUPS(2). It is no effective to set this value to noTurnOnUPS(1).
INT upsAdvanceControlUpsOff	1.3.6.1.4.1.3808.1.1.1.6.2.1	INTEGER	read-write	UPS will shutdown when the variable is set to turnUpsOff(2). UPS will shutdown after a delay period specified by upsAdvanceConfigShutoffDelay when the variable is Set to turnUpsOffGracefully(3). Without regard to the utility state the UPS will not provide output power in this state. It is no effective to set this value to noTurnUpsOff(1).
INT upsAdvanceControlUpsSleep	1.3.6.1.4.1.3808.1.1.1.6.2.3	INTEGER	read-write	UPS will enter sleep mode when the variable is set to putUpsToSleep(2). UPS will enter sleep mode after a delay period specified by upsAdvanceConfigSleepDelay when the variable is Set to putUpsToSleepGracefully(3). Without regard to the utility state the UPS will not provide output power in sleep mode. Output power will recover when specified time has elapsed. It is no effective to set this value to noPutUpsToSleep(1).
upsAdvanceIdent	1.3.6.1.4.1.3808.1.1.1.1.2
STR upsAdvanceIdentAgentFirmwareRevision	1.3.6.1.4.1.3808.1.1.1.1.2.4	DisplayString	read-only	The SNMP agent firmware revision.
STR upsAdvanceIdentAgentSerialNumber	1.3.6.1.4.1.3808.1.1.1.1.2.9	DisplayString	read-only	A string identifying the serial number of the Agent.
INT upsAdvanceIdentCurrentRating	1.3.6.1.4.1.3808.1.1.1.1.2.8	INTEGER	read-only	The output current rating of the UPS. Measured in tenths of Amps.
STR upsAdvanceIdentDateOfManufacture	1.3.6.1.4.1.3808.1.1.1.1.2.2	DisplayString	read-only	The UPS manufacture date in mm/dd/yy format.
STR upsAdvanceIdentFirmwareRevision	1.3.6.1.4.1.3808.1.1.1.1.2.1	DisplayString	read-only	The UPS firmware revision.
STR upsAdvanceIdentLCDFirmwareVersion	1.3.6.1.4.1.3808.1.1.1.1.2.5	DisplayString	read-only	The revision number of the UPS LCD firmware.
INT upsAdvanceIdentLoadPower	1.3.6.1.4.1.3808.1.1.1.1.2.7	INTEGER	read-only	The power rating(Watts) of the UPS.
INT upsAdvanceIdentPowerRating	1.3.6.1.4.1.3808.1.1.1.1.2.6	INTEGER	read-only	The Volt-Amp rating of the UPS.
STR upsAdvanceIdentSerialNumber	1.3.6.1.4.1.3808.1.1.1.1.2.3	DisplayString	read-only	The UPS serial number in the internal microprocessor.
upsAdvanceInput	1.3.6.1.4.1.3808.1.1.1.3.2
GAU upsAdvanceInputFrequency	1.3.6.1.4.1.3808.1.1.1.3.2.4	Gauge	read-only	The input line frequency in 1/10 Hz.
INT upsAdvanceInputLineFailCause	1.3.6.1.4.1.3808.1.1.1.3.2.5	INTEGER	read-only	The reason of UPS power failure. This value is set to: - noTransfer(1), if UPS is in utility mode. - highLineVoltage(2), if UPS switch to battery mode by reason of input voltage over the high transfer vloltage. - brownout(3), if UPS switch to battery mode by reason of input voltage under the low transfer vloltage. - selfTest(4), if the UPS was commanded to do a self test.
GAU upsAdvanceInputLineVoltage	1.3.6.1.4.1.3808.1.1.1.3.2.1	Gauge	read-only	The input line voltage in 1/10 VAC.
GAU upsAdvanceInputMaxLineVoltage	1.3.6.1.4.1.3808.1.1.1.3.2.2	Gauge	read-only	The maximum input line voltage in 1/10 VAC over the previous 1 minute period.
GAU upsAdvanceInputMinLineVoltage	1.3.6.1.4.1.3808.1.1.1.3.2.3	Gauge	read-only	The minimum input line voltage in 1/10 VAC over the previous 1 minute period.
INT upsAdvanceInputStatus	1.3.6.1.4.1.3808.1.1.1.3.2.6	INTEGER	read-only	Display the present status of the utility power supplied to the UPS.
upsAdvanceOutput	1.3.6.1.4.1.3808.1.1.1.4.2
GAU upsAdvanceOutputCurrent	1.3.6.1.4.1.3808.1.1.1.4.2.4	Gauge	read-only	The UPS output current in 1/10 Amps.
GAU upsAdvanceOutputFrequency	1.3.6.1.4.1.3808.1.1.1.4.2.2	Gauge	read-only	The UPS output frequency in 1/10 Hz.
GAU upsAdvanceOutputLoad	1.3.6.1.4.1.3808.1.1.1.4.2.3	Gauge	read-only	The UPS output load expressed in percentage
GAU upsAdvanceOutputPower	1.3.6.1.4.1.3808.1.1.1.4.2.5	Gauge	read-only	The total output active power of the UPS system in W.
GAU upsAdvanceOutputVoltage	1.3.6.1.4.1.3808.1.1.1.4.2.1	Gauge	read-only	The UPS output voltage in 1/10 VAC.
INT upsAdvanceSleepAfterDelay	1.3.6.1.4.1.3808.1.1.1.6.2.7	INTEGER	read-write	UPS will enter sleep mode after indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown.
upsAdvanceTest	1.3.6.1.4.1.3808.1.1.1.7.2
INT upsAdvanceTestDiagnostics	1.3.6.1.4.1.3808.1.1.1.7.2.2	INTEGER	read-write	UPS will do a diagnostic selftest when the variable is set to testDiagnostics(2). It is no effective to set this value to noTestDiagnostics(1).
INT upsAdvanceTestDiagnosticSchedule	1.3.6.1.4.1.3808.1.1.1.7.2.1	INTEGER	read-write	The schedule of the UPS automatic selftest.
INT upsAdvanceTestDiagnosticsResults	1.3.6.1.4.1.3808.1.1.1.7.2.3	INTEGER	read-only	The last UPS selftest result.
STR upsAdvanceTestEstimationDate	1.3.6.1.4.1.3808.1.1.1.7.2.8	DisplayString	read-only	The last UPS runtime estimation date
INT upsAdvanceTestEstimationResults	1.3.6.1.4.1.3808.1.1.1.7.2.7	INTEGER	read-only	The last runtime estimation result. This value means : - ok(1), if a successful runtime estimation. - invalidEstimation(2), if runtime estimation failure. - estimationInProgress(3), if estimation is processing now.
INT upsAdvanceTestIndicators	1.3.6.1.4.1.3808.1.1.1.7.2.5	INTEGER	read-write	UPS will perform a panel indicator test when the variable is set to testIndicators(2). It is no effective to set this value to noTestIndicators(1).
STR upsAdvanceTestLastDiagnosticsDate	1.3.6.1.4.1.3808.1.1.1.7.2.4	DisplayString	read-only	The last UPS selftest date in mm/dd/yy format.
INT upsAdvanceTestRuntimeEstimation	1.3.6.1.4.1.3808.1.1.1.7.2.6	INTEGER	read-write	UPS will discharge to calibrate the UPS runtime when the variable is set to performEstimation(2). This test runs until the UPS is in a low battery condition. UPS will cancel the discharge after setting performEstimation(2) when the variable is set to cancelCurrentEstimation(3). It is no effective to set this value to noPerformEstimation(1). The result of the runtime test will be stored in upsAdvanceTestEstimationResults.
INT upsBankControlIndex	1.3.6.1.4.1.3808.1.1.1.8.1.1.1.1	INTEGER	read-only	The index to the outlet entry.
INT upsBankControlOutletCommand	1.3.6.1.4.1.3808.1.1.1.8.1.1.1.2	INTEGER	read-write	Getting this variable will return the outlet bank state. If the outlet bank is on, the immediateOn (1) value will be returned. If the outlet bank is off, the immediateOff (2) value will be returned. If the outlet bank is critical (uncontrollable), the criticalBank (4) value will be returned. Setting this variable to immediateOn (1) will immediately turn the outlet on. Setting this variable to immediateOff (2) will immediately turn the outlet off.
upsBankOutletControl	1.3.6.1.4.1.3808.1.1.1.8.1
upsBankOutletControlEntry	1.3.6.1.4.1.3808.1.1.1.8.1.1.1		not-accessible	The outlet to control.
upsBankOutletControlTable	1.3.6.1.4.1.3808.1.1.1.8.1.1		not-accessible	Allows for control of the outlet banks.
upsBaseBattery	1.3.6.1.4.1.3808.1.1.1.2.1
INT upsBaseBatteryAgeRecommand	1.3.6.1.4.1.3808.1.1.1.2.1.4	INTEGER	read-only	Recommended battery life in month
STR upsBaseBatteryLastReplaceDate	1.3.6.1.4.1.3808.1.1.1.2.1.3	DisplayString	read-write	The UPS batteries last replaced date in mm/dd/yyyy format. This value is originally set when manufactured. If batteries replaced, administrator should reset this value.
INT upsBaseBatteryStatus	1.3.6.1.4.1.3808.1.1.1.2.1.1	INTEGER	read-only	The UPS battery status. A batteryLow(3) value means the battery will be exhausted soon under the current load. The amount of low battery run time can be configured by the upsAdvanceConfigLowBatteryRunTime.
TIK upsBaseBatteryTimeOnBattery	1.3.6.1.4.1.3808.1.1.1.2.1.2	TimeTicks	read-only	The UPS wasted battery time since the UPS has transfered to backup mode.
upsBaseConfig	1.3.6.1.4.1.3808.1.1.1.5.1
upsBaseConfigDeviceEntry	1.3.6.1.4.1.3808.1.1.1.5.1.2.1		not-accessible	The equipment plugged in to the UPS.
upsBaseConfigDeviceTable	1.3.6.1.4.1.3808.1.1.1.5.1.2		not-accessible	A list of equipment plugged into the UPS. The numbers of entries are given by the value of upsBaseConfigNumDevices.
INT upsBaseConfigNumDevices	1.3.6.1.4.1.3808.1.1.1.5.1.1	INTEGER	read-only	The number of equipment plugged into the UPS.
upsBaseControl	1.3.6.1.4.1.3808.1.1.1.6.1
INT upsBaseControlConserveBattery	1.3.6.1.4.1.3808.1.1.1.6.1.1	INTEGER	read-write	UPS on battery will enter sleeping when the variable is set to turnOffUpsToConserveBattery(2). When utility power recovers the UPS will turn back on. Trying to turn off a UPS that is not on battery mode will cause badValue error. It is no effective to set this value to noTurnOffUps(1).
upsBaseIdent	1.3.6.1.4.1.3808.1.1.1.1.1
STR upsBaseIdentModel	1.3.6.1.4.1.3808.1.1.1.1.1.1	DisplayString	read-only	The UPS model name.
STR upsBaseIdentName	1.3.6.1.4.1.3808.1.1.1.1.1.2	DisplayString	read-write	The UPS identified name could be set by the administrator.
upsBaseInput	1.3.6.1.4.1.3808.1.1.1.3.1
INT upsBaseInputPhase	1.3.6.1.4.1.3808.1.1.1.3.1.1	INTEGER	read-only	The AC input phase.
upsBaseOutput	1.3.6.1.4.1.3808.1.1.1.4.1
INT upsBaseOutputPhase	1.3.6.1.4.1.3808.1.1.1.4.1.2	INTEGER	read-only	The output phase.
INT upsBaseOutputStatus	1.3.6.1.4.1.3808.1.1.1.4.1.1	INTEGER	read-only	The UPS output status.
STR upsBaseOutputWorkingFrequency	1.3.6.1.4.1.3808.1.1.1.4.1.3	DisplayString	read-only	The frequency of the UPS output power.
upsBaseTest	1.3.6.1.4.1.3808.1.1.1.7.1
upsBattery	1.3.6.1.4.1.3808.1.1.1.2
NTF upsBatteryExpiration	1.3.6.1.4.1.3808.0.49			WARNING: The battery may not work well anymore.
NTF upsBatteryNotPresent	1.3.6.1.4.1.3808.0.39			WARNING: Battery is not present.
NTF upsBatteryOverThreeYear	1.3.6.1.4.1.3808.0.48			WARNING: Battery has been 3 years from last Replacement.
NTF upsBatteryReplacement	1.3.6.1.4.1.3808.0.50			WARNING: The battery has been replaced.
NTF upsBoostOn	1.3.6.1.4.1.3808.0.6			WARNING: The UPS has enabled boost, low utility voltage.
NTF upsBuckOn	1.3.6.1.4.1.3808.0.18			WARNING: The UPS has enabled buck, high utility voltage.
NTF upsBypassOverload	1.3.6.1.4.1.3808.0.44			WARNING: The UPS bypass overload.
NTF upsBypassOverloadCleared	1.3.6.1.4.1.3808.0.45			INFORMATION: The UPS bypass overload has been cleared.
NTF upsChargerFailure	1.3.6.1.4.1.3808.0.23			WARNING: The battery charger is abnormal.
NTF upsCommandCancel	1.3.6.1.4.1.3808.0.33			INFORMATION: The cancel command has been executed.
upsConfig	1.3.6.1.4.1.3808.1.1.1.5
upsControl	1.3.6.1.4.1.3808.1.1.1.6
NTF upsDiagnosticsFailed	1.3.6.1.4.1.3808.0.3			SEVERE: The UPS battery test failed.
NTF upsDiagnosticsPassed	1.3.6.1.4.1.3808.0.10			INFORMATIONAL: The UPS battery test passed.
NTF upsDischarged	1.3.6.1.4.1.3808.0.4			SEVERE: The UPS has started a runtime estimation process.
NTF upsEmergencyPowerOff	1.3.6.1.4.1.3808.0.30			Emergency Power Off (EPO)
NTF upsEnterBypassMode	1.3.6.1.4.1.3808.0.42			WARNING: The UPS enters bypass mode.
NTF upsEnterECOMode	1.3.6.1.4.1.3808.0.46			WARNING: The UPS enters ECO mode.
NTF upsEnterSleep	1.3.6.1.4.1.3808.0.22			WARNING: The UPS started sleep sequence.
NTF upsEstimationAbort	1.3.6.1.4.1.3808.0.37			WARNING: The UPS runtime estimation aborted.
NTF upsFirmwareUpgradeEnd	1.3.6.1.4.1.3808.0.57			WARNING: UPS firmware update is over.
NTF upsFirmwareUpgradeStart	1.3.6.1.4.1.3808.0.56			WARNING: UPS firmware starts to update.
NTF upsHardwareFault	1.3.6.1.4.1.3808.0.38			WARNING: The UPS hardware fault.
upsIdent	1.3.6.1.4.1.3808.1.1.1.1
upsInput	1.3.6.1.4.1.3808.1.1.1.3
NTF upsLostRedundant	1.3.6.1.4.1.3808.0.28			WARNING: Not enough power redundancy modules.
NTF upsModuleFanAlarm	1.3.6.1.4.1.3808.0.53			WARNING: The UPS module fan alarm.
NTF upsModuleInvertorAlarm	1.3.6.1.4.1.3808.0.51			WARNING: The UPS module invertor alarm.
NTF upsModuleManualShutdown	1.3.6.1.4.1.3808.0.54			WARNING: The UPS module manual shutdown.
NTF upsModuleOverload	1.3.6.1.4.1.3808.0.55			WARNING: The UPS module overload.
NTF upsModuleRectifierAlarm	1.3.6.1.4.1.3808.0.52			WARNING: The UPS module rectifier alarm.
NTF upsOnBattery	1.3.6.1.4.1.3808.0.5			WARNING: Utility power failed, transfer to backup mode.
upsOutlet	1.3.6.1.4.1.3808.1.1.1.8
upsOutput	1.3.6.1.4.1.3808.1.1.1.4
NTF upsOverload	1.3.6.1.4.1.3808.0.2			SEVERE: The UPS has sensed an overload condition.
NTF upsOverTemp	1.3.6.1.4.1.3808.0.16			SEVERE: The UPS inner temperature is too high.
upsPhase	1.3.6.1.4.1.3808.1.1.1.9
upsPhaseBypass	1.3.6.1.4.1.3808.1.1.1.9.3
INT upsPhaseBypassCurrent	1.3.6.1.4.1.3808.1.1.1.9.3.2.1.3	INTEGER	read-only	Getting this OID will return the bypass current that each phase of the UPS can provide. It is represented in 1/10 Amps.
upsPhaseBypassEntry	1.3.6.1.4.1.3808.1.1.1.9.3.2.1		not-accessible	The UPS Phase Bypass Access.
INT upsPhaseBypassFrequency	1.3.6.1.4.1.3808.1.1.1.9.3.2.1.4	INTEGER	read-only	Getting this OID will return the bypass frequency that each phase of the UPS can provide. It is represented in 1/10 Hz.
INT upsPhaseBypassPowerFactor	1.3.6.1.4.1.3808.1.1.1.9.3.2.1.5	INTEGER	read-only	Getting this OID will return the bypass power factor that each phase of the UPS can provide. It is represented in 1/100.
upsPhaseBypassTable	1.3.6.1.4.1.3808.1.1.1.9.3.2		not-accessible	Allows for getting the Phase Bypass in the UPS
INT upsPhaseBypassTableIndex	1.3.6.1.4.1.3808.1.1.1.9.3.2.1.1	INTEGER	read-only	The index to the UPS Phase Bypass entry.
INT upsPhaseBypassTableSize	1.3.6.1.4.1.3808.1.1.1.9.3.1	INTEGER	read-only	Getting this OID will return the Phase number.
INT upsPhaseBypassVoltage	1.3.6.1.4.1.3808.1.1.1.9.3.2.1.2	INTEGER	read-only	Getting this OID will return the bypass voltage that each phase of the UPS can provide. It is represented in 1/10 VAC.
upsPhaseInput	1.3.6.1.4.1.3808.1.1.1.9.1
INT upsPhaseInputCurrent	1.3.6.1.4.1.3808.1.1.1.9.1.2.1.3	INTEGER	read-only	Getting this OID will return the input current that each phase of the UPS can provide. It is represented in 1/10 Amps.
upsPhaseInputEntry	1.3.6.1.4.1.3808.1.1.1.9.1.2.1		not-accessible	The UPS Phase Input Access.
INT upsPhaseInputFrequency	1.3.6.1.4.1.3808.1.1.1.9.1.2.1.4	INTEGER	read-only	Getting this OID will return the input frequency that each phase of the UPS can provide. It is represented in 1/10 Hz.
INT upsPhaseInputPowerFactor	1.3.6.1.4.1.3808.1.1.1.9.1.2.1.5	INTEGER	read-only	Getting this OID will return the input power factor that each phase of the UPS can provide. It is represented in 1/100.
upsPhaseInputTable	1.3.6.1.4.1.3808.1.1.1.9.1.2		not-accessible	Allows for getting the Phase Input in the UPS
INT upsPhaseInputTableIndex	1.3.6.1.4.1.3808.1.1.1.9.1.2.1.1	INTEGER	read-only	The index to the UPS Phase Input entry.
INT upsPhaseInputTableSize	1.3.6.1.4.1.3808.1.1.1.9.1.1	INTEGER	read-only	Getting this OID will return the phase number.
INT upsPhaseInputVoltage	1.3.6.1.4.1.3808.1.1.1.9.1.2.1.2	INTEGER	read-only	Getting this OID will return the input voltage that each phase of the UPS can provide. It is represented in 1/10 VAC.
upsPhaseOutput	1.3.6.1.4.1.3808.1.1.1.9.2
INT upsPhaseOutputCurrent	1.3.6.1.4.1.3808.1.1.1.9.2.2.1.3	INTEGER	read-only	Getting this OID will return the output current that each phase of the UPS can provide. It is represented in 1/10 Amps.
upsPhaseOutputEntry	1.3.6.1.4.1.3808.1.1.1.9.2.2.1		not-accessible	The UPS Phase Output Access.
INT upsPhaseOutputFrequency	1.3.6.1.4.1.3808.1.1.1.9.2.2.1.4	INTEGER	read-only	Getting this OID will return the output frequency that each phase of the UPS can provide. It is represented in 1/10 Hz.
INT upsPhaseOutputPower	1.3.6.1.4.1.3808.1.1.1.9.2.2.1.6	INTEGER	read-only	Getting this OID will return the output power that each phase of the UPS can provide. It is represented in Watt.
INT upsPhaseOutputPowerFactor	1.3.6.1.4.1.3808.1.1.1.9.2.2.1.5	INTEGER	read-only	Getting this OID will return the output power factor that each phase of the UPS can provide. It is represented in 1/100.
upsPhaseOutputTable	1.3.6.1.4.1.3808.1.1.1.9.2.2		not-accessible	Allows for getting the Phase Output in the UPS
INT upsPhaseOutputTableIndex	1.3.6.1.4.1.3808.1.1.1.9.2.2.1.1	INTEGER	read-only	The index to the UPS Phase Output entry.
INT upsPhaseOutputTableSize	1.3.6.1.4.1.3808.1.1.1.9.2.1	INTEGER	read-only	Getting this OID will return the Phase number.
INT upsPhaseOutputVoltage	1.3.6.1.4.1.3808.1.1.1.9.2.2.1.2	INTEGER	read-only	Getting this OID will return the output voltage that each phase of the UPS can provide. It is represented in 1/10 VAC.
NTF upsRebootStarted	1.3.6.1.4.1.3808.0.15			WARNING: The UPS started reboot sequence.
NTF upsRemainRuntimeLowThanThreshold	1.3.6.1.4.1.3808.0.35			WARNING: The UPS remaining runtime is lower than threshold.
NTF upsRemoteCommandFailed	1.3.6.1.4.1.3808.0.27			WARNING: The UPS remote command failed.
NTF upsReturnFromBypassMode	1.3.6.1.4.1.3808.0.43			INFORMATION: The UPS leaves bypass mode.
NTF upsReturnFromECOMode	1.3.6.1.4.1.3808.0.47			WARNING: The UPS leaves ECO mode.
NTF upsRFC1628TrapAlarmEntryAdded	1.3.6.1.4.1.3808.0.60			WARNING: RFC1628: Alarm entry added.
NTF upsRFC1628TrapOnBattery	1.3.6.1.4.1.3808.0.58			WARNING: RFC1628: UPS is on battery.
NTF upsRFC1628TrapTestCompleted	1.3.6.1.4.1.3808.0.59			WARNING: RFC1628: UPS test completed.
NTF upsScheduleShutdown	1.3.6.1.4.1.3808.0.21			WARNING: The UPS has started its schedule shutdown sequence.
NTF upsSignalClientShutdown	1.3.6.1.4.1.3808.0.29			SEVERE: The UPS has signaled clients to shutdown.
NTF upsSleeping	1.3.6.1.4.1.3808.0.13			WARNING: The UPS entered sleep mode. Output power will not be provided.
NTF upsStartBatteryTest	1.3.6.1.4.1.3808.0.34			INFORMATION: The UPS has started a battery test process.
INT upsStatus	1.3.6.1.4.1.3808.1.1.1.10.1	INTEGER	read-only	The UPS system status.
upsSystem	1.3.6.1.4.1.3808.1.1.1.10
upsTest	1.3.6.1.4.1.3808.1.1.1.7
NTF upsTurnedOff	1.3.6.1.4.1.3808.0.12			WARNING: The UPS has been turned off.
NTF upsTurnedOn	1.3.6.1.4.1.3808.0.26			WARNING: The UPS has been turned on.
NTF upsTurnoffStarted	1.3.6.1.4.1.3808.0.25			WARNING: The UPS started turn off sequence.
NTF upsWiringFault	1.3.6.1.4.1.3808.0.40			WARNING: The UPS wiring fault has been detected.
NTF upsWiringFaultCleared	1.3.6.1.4.1.3808.0.41			INFORMATION: The UPS wiring fault has been cleared.
NTF upsWokeUp	1.3.6.1.4.1.3808.0.14			INFORMATION: The UPS woke up from sleep mode. Output power is being provided.
INT vaRating	1.3.6.1.4.1.3808.1.1.1.5.1.2.1.3	INTEGER	read-write	The VA rating of the equipment plugged into the UPS.

RFC description

Manages CyberPower UPS, power distribution, and environmental monitoring for power management systems.

Start monitoring UPS product line (vendor unclear, enterprise OID 3808) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CPS-MIB

What Is CPS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description