CM-SA-MIB

All MIBs › CM-SA-MIB

Organization: ADVA Optical Networking

Last Updated: 2011-11-22

Category: Quality of Service, Vendor: Ceragon

Description: Manages service access (SA) parameters and traffic profiles for Ceragon microwave radio systems.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CM-SA-MIB?

CM-SA-MIB is an ADVA Optical Networking proprietary MIB providing Service Assurance test capabilities (ECPA — Ethernet Continuity/Performance Assessment) for the F3 (FSP150CM/CC) product lines. Its control table, keyed by index, configures source port, test type, frame count/duration, injector/monitor direction, up to three configured test streams, a start/stop action, test status, storage type, and row status, while a stream-configuration table defines each stream's name, frame size, rate, payload type, signature, and destination MAC address. As a diagnostic/configuration MIB it lets an administrator run an on-demand Ethernet service-assurance test between two points and review its pass/fail status. It is deployed on ADVA Optical Networking FSP150CM/CC (F3) platforms. Engineers can download the CM-SA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CM-SA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ADVA Optical Networking FSP150CM/CC (F3) platforms

Monitoring Examples

A field engineer configures ecpaConfigStreamTable with the required frame size and rate, then triggers ecpaControlAction to run a service-assurance test before turning up a new Ethernet circuit on an ADVA FSP150.

What Can Be Monitored

Ethernet service-assurance test configuration and status

Imported Objects

From ADVA-MIB

fsp150cm

OBJECT-IDENTITY

From CM-COMMON-MIB

AdminState
ClassOfServiceType
CmPmBinAction
IpPriorityMapMode
IpVersion
MepDestinationType
OperationalState
PerfCounter32
PerfCounter64
SchedActivityStatus
ScheduleType
SecondaryState
TrafficDirection
VlanId
VlanPriority

From CM-ENTITY-MIB

neIndex	OBJECT-TYPE
shelfIndex	OBJECT-TYPE
slotIndex	OBJECT-TYPE

From CM-FACILITY-MIB

BitErrRate
PolicerColorMode

From IEEE8021-CFM-MIB

Dot1agCfmMepIdOrZero

From IPV6-TC

Ipv6Address

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
RowStatus
StorageType
TEXTUAL-CONVENTION
TruthValue
VariablePointer

OIDs

OID symbolic	OID numeric	Type	Access	Description
cmServiceAssuranceMIB	1.3.6.1.4.1.2544.1.12.8			This module defines the Service Assurance MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.
cmServAssuranceObjects	1.3.6.1.4.1.2544.1.12.8.1
ecpaControlTable	1.3.6.1.4.1.2544.1.12.8.1.1		not-accessible	A list of entries for the control of Etherjack Connection Performance Analyzer Streams. Upto 12 ECPA streams can be configured per test head; 3 ECPA streams can be simultaneously executed.
ecpaControlEntry	1.3.6.1.4.1.2544.1.12.8.1.1.1		not-accessible	A conceptual row in the ecpaControlTable.
I32 ecpaControlIndex	1.3.6.1.4.1.2544.1.12.8.1.1.1.1	Integer32	read-only	An arbitrary integer index value used to uniquely identify this Etherjack Connection Performance Analyzer Control Test head. There is only one test head per card.
NUM ecpaControlSourcePort	1.3.6.1.4.1.2544.1.12.8.1.1.1.2	VariablePointer	read-write	Pointer to the Access or Network Port on which the ECPA test will be started within a card.
ECP ecpaControlTestType	1.3.6.1.4.1.2544.1.12.8.1.1.1.3	EcpaTestType	read-write	The type of ECPA test to be performed. When 'duration' test is specified, ECPA test is run for 'ecpaControlDuration' time. When 'numFrames' test is specified, ECPA test is run for 'ecpaControlNumFrames', when 'continous' test is specified, ECPA test is run until an explicit 'ecpaControlAction' of 'stop' of received.
I32 ecpaControlNumFrames	1.3.6.1.4.1.2544.1.12.8.1.1.1.4	Integer32	read-write	This object enables specification of the number of frames for traffic generation. Traffic Generation will be completed after the specified number of frames are transmitted.
I32 ecpaControlDuration	1.3.6.1.4.1.2544.1.12.8.1.1.1.5	Integer32	read-write	This object enables specification of the time in seconds for traffic generation. Traffic Generation will be stopped after the specified time interval is exhausted.
TRA ecpaControlInjectorDirection	1.3.6.1.4.1.2544.1.12.8.1.1.1.6	TrafficDirection	read-write	This object enables specification of the direction of traffic generation. This value must be specified if the interface is used for traffic generation. Both of ecpaControlInjectorDirection and ecpaControlMonitorDirection must be specified.
TRA ecpaControlMonitorDirection	1.3.6.1.4.1.2544.1.12.8.1.1.1.7	TrafficDirection	read-write	This object enables specification of the direction of receival of generated traffic. This value must be specified if the interface is used for receiving/monitoring generated traffic. Both of ecpaControlInjectorDirection and ecpaControlMonitorDirection must be specified.
I32 ecpaControlStream1	1.3.6.1.4.1.2544.1.12.8.1.1.1.8	Integer32	read-write	This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream1. Non 0 value indicates the selected ECPA stream.
I32 ecpaControlStream2	1.3.6.1.4.1.2544.1.12.8.1.1.1.9	Integer32	read-write	This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream2. Non 0 value indicates the selected ECPA stream.
I32 ecpaControlStream3	1.3.6.1.4.1.2544.1.12.8.1.1.1.10	Integer32	read-write	This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream3. Non 0 value indicates the selected ECPA stream.
ECP ecpaControlAction	1.3.6.1.4.1.2544.1.12.8.1.1.1.11	EcpaControlAction	read-write	This object enables starting/stopping of traffic generation as well as resetting of monitored streams. This object may not be specified at configuration creation time - in this case it will take the value of `none'. This allows manager to explicitly control the start and stop of traffic generation/monitoring activity. Value of `stop' is invalid if the activity is specified but not started. Value of `start' is valid during creation time, as well as when activity is already stopped. Specification of `reset' resets the specified streams to default values, as well as clears the control specification. Get on this variable gives the most recent SNMP set specification.
ECP ecpaControlTestStatus	1.3.6.1.4.1.2544.1.12.8.1.1.1.12	EcpaTestStatus	read-only	This object reflects the current status of test set configuration entry. Upon creation, the status has a value of `initial'; the status changes to `in-progress' upon ecpaControlAction indicating `start'; the status changes to `completed' upon ecpaControlAction indicating stop, as well as when the specified test generation completes autonomously upon completion of number of frames or completion of specified time interval.
STO ecpaControlStorageType	1.3.6.1.4.1.2544.1.12.8.1.1.1.13	StorageType	read-create	The type of storage configured for this entry.
ROW ecpaControlRowStatus	1.3.6.1.4.1.2544.1.12.8.1.1.1.14	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of ecpaControlRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with ecpaControlRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The ecpaControlRowStatus object may be modified if the associated instance of this object is equal to active(1).
ecpaConfigStreamTable	1.3.6.1.4.1.2544.1.12.8.1.2		not-accessible	A list of entries for the configuration of Etherjack Connection Performance Analyzer Stream Specifications.
ecpaConfigStreamEntry	1.3.6.1.4.1.2544.1.12.8.1.2.1		not-accessible	A conceptual row in the ecpaConfigStreamTable.
I32 ecpaConfigStreamIndex	1.3.6.1.4.1.2544.1.12.8.1.2.1.1	Integer32	read-write	An arbitrary integer index value used to uniquely identify this Etherjack Connection Performance Analyzer.
STR ecpaConfigStreamName	1.3.6.1.4.1.2544.1.12.8.1.2.1.2	DisplayString	read-write	Symbolic Stream Name that can be associated with an ECPA stream.
I32 ecpaConfigStreamFrameSize	1.3.6.1.4.1.2544.1.12.8.1.2.1.3	Integer32	read-write	This object enables specification of fixed length frame size in bytes for traffic generation. If not specified, default value of 64 bytes is used. CM Aggregation Product limits the upper range value to 9600.
U32 ecpaConfigStreamRate	1.3.6.1.4.1.2544.1.12.8.1.2.1.4	Unsigned32	read-write	The object enables specification of the traffic generation rate.
ECP ecpaConfigStreamPayloadType	1.3.6.1.4.1.2544.1.12.8.1.2.1.5	EcpaPayloadType	read-write	This object enables specification of type of payload to generate `fixed' type indicates a generation pattern of 5A, A5, 5A, A5 bytes. `random' type indicates traffic generation with pseudo-random pattern.
STR ecpaConfigStreamSignature	1.3.6.1.4.1.2544.1.12.8.1.2.1.6	DisplayString	read-write	Indicates an 8-byte signature specified by the user in hexadecimal or ASCII format. This signature is currently used by the FSP150Mx products for test frame recognition and will be appended directly after the ECPA Signature in the test frame and be 4-byte aligned. This will allow the F3 ECPA feature to interoperate with the existing FSP150Mx products. Hexadecimal signature must be prefixed with 0x/0X.
MAC ecpaConfigStreamDestinationMAC	1.3.6.1.4.1.2544.1.12.8.1.2.1.7	MacAddress	read-write	Allows specification of destination MAC in the generated traffic.
MAC ecpaConfigStreamSourceMAC	1.3.6.1.4.1.2544.1.12.8.1.2.1.8	MacAddress	read-write	Allows specification of source MAC in the generated traffic.
T/F ecpaConfigStreamOuterVlanEnabled	1.3.6.1.4.1.2544.1.12.8.1.2.1.9	TruthValue	read-write	Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
VLA ecpaConfigStreamOuterVlanId	1.3.6.1.4.1.2544.1.12.8.1.2.1.10	VlanId	read-write	Outer VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
VLA ecpaConfigStreamOuterVlanPrio	1.3.6.1.4.1.2544.1.12.8.1.2.1.11	VlanPriority	read-write	Outer VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
I32 ecpaConfigStreamOuterVlanEtherType	1.3.6.1.4.1.2544.1.12.8.1.2.1.12	Integer32	read-write	EtherType associated with the Outer VLAN Tag. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
T/F ecpaConfigStreamInnerVlanEnabled	1.3.6.1.4.1.2544.1.12.8.1.2.1.13	TruthValue	read-write	Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
VLA ecpaConfigStreamInnerVlanId	1.3.6.1.4.1.2544.1.12.8.1.2.1.14	VlanId	read-write	Inner VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
VLA ecpaConfigStreamInnerVlanPrio	1.3.6.1.4.1.2544.1.12.8.1.2.1.15	VlanPriority	read-write	Inner VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
I32 ecpaConfigStreamInnerVlanEtherType	1.3.6.1.4.1.2544.1.12.8.1.2.1.16	Integer32	read-write	EtherType associated with the Inner VLAN Tag. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
IPV ecpaConfigStreamIpVersion	1.3.6.1.4.1.2544.1.12.8.1.2.1.17	IpVersion	read-write	This object enables specification of IP data in the generated test traffic. Value of `ipv4' allows test data to be IP v4 compatible. Value of `ipv6' allows test data to be IP v6 compatible.
IP ecpaConfigStreamIpV4Address	1.3.6.1.4.1.2544.1.12.8.1.2.1.18	IpAddress	read-write	This object enables specification of ipv4 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv4.
ADR ecpaConfigStreamIpV6Address	1.3.6.1.4.1.2544.1.12.8.1.2.1.19	Ipv6Address	read-write	This object enables specification of ipv6 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv6.
IPP ecpaConfigStreamPrioMapMode	1.3.6.1.4.1.2544.1.12.8.1.2.1.20	IpPriorityMapMode	read-write	This object enables specification of Priority Mapping Mode for the test stream.
I32 ecpaConfigStreamPrioVal	1.3.6.1.4.1.2544.1.12.8.1.2.1.21	Integer32	read-write	This object enables specification of Priority Value for ecpaConfigStreamPrioMapMode as TOS/DSCP.
T/F ecpaConfigStreamInnerVlan2Enabled	1.3.6.1.4.1.2544.1.12.8.1.2.1.22	TruthValue	read-write	Allows specification of a VLAN tagged ECPA stream. This variable enables the second(inner) VLAN specification, in the case of a 3-tagged ECPA stream. If a three tagged ECPA stream is desired, this specification is mandatory.
VLA ecpaConfigStreamInnerVlan2Id	1.3.6.1.4.1.2544.1.12.8.1.2.1.23	VlanId	read-write	Inner (second) VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
VLA ecpaConfigStreamInnerVlan2Prio	1.3.6.1.4.1.2544.1.12.8.1.2.1.24	VlanPriority	read-write	Inner (second) VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
I32 ecpaConfigStreamInnerVlan2EtherType	1.3.6.1.4.1.2544.1.12.8.1.2.1.25	Integer32	read-write	EtherType associated with the Inner (second) VLAN Tag. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
IP ecpaConfigStreamDestIpV4Address	1.3.6.1.4.1.2544.1.12.8.1.2.1.26	IpAddress	read-write	This object enables specification of destination ipv4 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv4.
ADR ecpaConfigStreamDestIpV6Address	1.3.6.1.4.1.2544.1.12.8.1.2.1.27	Ipv6Address	read-write	This object enables specification of destination ipv6 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv6.
T/F ecpaConfigStreamUsePortSourceMAC	1.3.6.1.4.1.2544.1.12.8.1.2.1.28	TruthValue	read-write	This object when not enabled indicates that MAC Address specified by ecpaConfigStreamSourceMAC as the source MAC Address of the ECPA test stream. For EGX, if enabled indicates that the corresponding ECPA test stream will use the associated Source Port's MAC Address. For GE110 products and CC products, if enabled indicates that the corresponding ECPA test stream will use the associated Source Port's Diagnostic MAC Address.
U32 ecpaConfigStreamRateHi	1.3.6.1.4.1.2544.1.12.8.1.2.1.29	Unsigned32	read-write	The object enables specification of the higher 32 bits of the traffic generation rate.
ecpaTestStreamTable	1.3.6.1.4.1.2544.1.12.8.1.3		not-accessible	A list of entries containing results of a previous test.
ecpaTestStreamEntry	1.3.6.1.4.1.2544.1.12.8.1.3.1		not-accessible	A conceptual row in the ecpaTestStreamTable. Entries in this table show results of the current ECPA test.
I32 ecpaTestStreamIndex	1.3.6.1.4.1.2544.1.12.8.1.3.1.1	Integer32	read-only	An integer index value corresponding to the stream index for which the ECPA test was initiated.
NUM ecpaTestStreamSourcePort	1.3.6.1.4.1.2544.1.12.8.1.3.1.2	VariablePointer	read-only	An integer index value corresponding to the ifIndex for which the ECPA test was initiated.
STR ecpaTestStreamName	1.3.6.1.4.1.2544.1.12.8.1.3.1.3	DisplayString	read-write	Symbolic Stream Name that can be associated with an ECPA stream.
I32 ecpaTestStreamFrameSize	1.3.6.1.4.1.2544.1.12.8.1.3.1.4	Integer32	read-write	This object enables specification of fixed length frame size in bytes for traffic generation. If not specified, default value of 64 bytes is used.
U32 ecpaTestStreamRate	1.3.6.1.4.1.2544.1.12.8.1.3.1.5	Unsigned32	read-write	The object enables specification of the traffic generation rate.
ECP ecpaTestStreamPayloadType	1.3.6.1.4.1.2544.1.12.8.1.3.1.6	EcpaPayloadType	read-write	This object enables specification of type of payload to generate `fixed' type indicates a generation pattern of 5A, A5, 5A, A5 bytes. `random' type indicates traffic generation with pseudo-random pattern.
STR ecpaTestStreamSignature	1.3.6.1.4.1.2544.1.12.8.1.3.1.7	DisplayString	read-write	Indicates an 8-byte signature specified by the user in hexadecimal or ASCII format. This signature is currently used by the FSP150Mx products for test frame recognition and will be appended directly after the ECPA Signature in the test frame and be 4-byte aligned. This will allow the F3 ECPA feature to interoperate with the existing FSP150Mx products. Hexadecimal signature must be prefixed with 0x/0X.
MAC ecpaTestStreamDestinationMAC	1.3.6.1.4.1.2544.1.12.8.1.3.1.8	MacAddress	read-write	Allows specification of destination MAC in the generated traffic.
MAC ecpaTestStreamSourceMAC	1.3.6.1.4.1.2544.1.12.8.1.3.1.9	MacAddress	read-write	Allows specification of source MAC in the generated traffic.
T/F ecpaTestStreamOuterVlanEnabled	1.3.6.1.4.1.2544.1.12.8.1.3.1.10	TruthValue	read-write	Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
VLA ecpaTestStreamOuterVlanId	1.3.6.1.4.1.2544.1.12.8.1.3.1.11	VlanId	read-write	Outer VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
VLA ecpaTestStreamOuterVlanPrio	1.3.6.1.4.1.2544.1.12.8.1.3.1.12	VlanPriority	read-write	Outer VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
I32 ecpaTestStreamOuterVlanEtherType	1.3.6.1.4.1.2544.1.12.8.1.3.1.13	Integer32	read-write	EtherType associated with the Outer VLAN Tag. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
T/F ecpaTestStreamInnerVlanEnabled	1.3.6.1.4.1.2544.1.12.8.1.3.1.14	TruthValue	read-write	Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
VLA ecpaTestStreamInnerVlanId	1.3.6.1.4.1.2544.1.12.8.1.3.1.15	VlanId	read-write	Inner VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
VLA ecpaTestStreamInnerVlanPrio	1.3.6.1.4.1.2544.1.12.8.1.3.1.16	VlanPriority	read-write	Inner VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
I32 ecpaTestStreamInnerVlanEtherType	1.3.6.1.4.1.2544.1.12.8.1.3.1.17	Integer32	read-write	EtherType associated with the Inner VLAN Tag. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
IPV ecpaTestStreamIpVersion	1.3.6.1.4.1.2544.1.12.8.1.3.1.18	IpVersion	read-write	This object enables specification of IP data in the generated test traffic. Value of `ipv4' allows test data to be IP v4 compatible. Value of `ipv6' allows test data to be IP v6 compatible.
IP ecpaTestStreamIpV4Address	1.3.6.1.4.1.2544.1.12.8.1.3.1.19	IpAddress	read-write	This object enables specification of ipv4 IP Address for the test stream.This is used when ecpaTestStreamIpVersion is ipv4.
ADR ecpaTestStreamIpV6Address	1.3.6.1.4.1.2544.1.12.8.1.3.1.20	Ipv6Address	read-write	This object enables specification of ipv6 IP Address for the test stream.This is used when ecpaTestStreamIpVersion is ipv6.
IPP ecpaTestStreamPrioMapMode	1.3.6.1.4.1.2544.1.12.8.1.3.1.21	IpPriorityMapMode	read-write	This object enables specification of Priority Mapping Mode for the test stream.
I32 ecpaTestStreamPrioVal	1.3.6.1.4.1.2544.1.12.8.1.3.1.22	Integer32	read-write	This object enables specification of Priority Value for ecpaTestStreamPrioMapMode as TOS/DSCP.
DAT ecpaTestStreamMonStartTime	1.3.6.1.4.1.2544.1.12.8.1.3.1.23	DateAndTime	read-only	The start time of the ECPA test for this stream.
DAT ecpaTestStreamMonEndTime	1.3.6.1.4.1.2544.1.12.8.1.3.1.24	DateAndTime	read-only	The end time of the ECPA test for this stream.
I32 ecpaTestStreamMonElapsedTime	1.3.6.1.4.1.2544.1.12.8.1.3.1.25	Integer32	read-only	The elapsed time of ECPA test for this stream in seconds.
NUM ecpaTestStreamMonTxFrames	1.3.6.1.4.1.2544.1.12.8.1.3.1.26	PerfCounter64	read-only	The total number of frames transmitted(generated) so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
NUM ecpaTestStreamMonRxFrames	1.3.6.1.4.1.2544.1.12.8.1.3.1.27	PerfCounter64	read-only	The total number of frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
I32 ecpaTestStreamMonRxPercentSuccess	1.3.6.1.4.1.2544.1.12.8.1.3.1.28	Integer32	read-only	Received frames as a percentage of transmitted frames. This object does not exist if the ecpaControlTestStatus indicates initial state.
NUM ecpaTestStreamMonRxOutOfSeqErrs	1.3.6.1.4.1.2544.1.12.8.1.3.1.29	PerfCounter64	read-only	The total number of out of sequence errors received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
NUM ecpaTestStreamMonRxSeqGaps	1.3.6.1.4.1.2544.1.12.8.1.3.1.30	PerfCounter64	read-only	The total number of sequence gaps received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
NUM ecpaTestStreamMonRxNonEcpaFrames	1.3.6.1.4.1.2544.1.12.8.1.3.1.31	PerfCounter64	read-only	The total number of non ECPA frames received during the execution.
U32 ecpaTestStreamMonRxMinDelay	1.3.6.1.4.1.2544.1.12.8.1.3.1.32	Unsigned32	read-only	The minimum delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
U32 ecpaTestStreamMonRxMaxDelay	1.3.6.1.4.1.2544.1.12.8.1.3.1.33	Unsigned32	read-only	The maximum delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
U32 ecpaTestStreamMonRxAvgDelay	1.3.6.1.4.1.2544.1.12.8.1.3.1.34	Unsigned32	read-only	The average delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
I32 ecpaTestStreamMonRx1stFrameSize	1.3.6.1.4.1.2544.1.12.8.1.3.1.35	Integer32	read-only	Frame size of the Monitored First Frame.
STR ecpaTestStreamMonRx1stFrame1Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.36	DisplayString	read-only	The frame contents of the first received frame - first 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame2Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.37	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame3Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.38	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame4Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.39	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame5Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.40	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame6Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.41	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame7Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.42	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame8Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.43	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame9Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.44	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
STR ecpaTestStreamMonRx1stFrame10Octets	1.3.6.1.4.1.2544.1.12.8.1.3.1.45	DisplayString	read-only	The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
NUM ecpaTestStreamMonRxBitRate	1.3.6.1.4.1.2544.1.12.8.1.3.1.46	PerfCounter64	read-only	The object provides the average bit rate on the ECPA test stream.
T/F ecpaTestStreamInnerVlan2Enabled	1.3.6.1.4.1.2544.1.12.8.1.3.1.47	TruthValue	read-only	This variable indicates the second(inner) VLAN specification, in the case of a 3-tagged ECPA stream. If a three tagged ECPA stream is desired, this indicates true.
VLA ecpaTestStreamInnerVlan2Id	1.3.6.1.4.1.2544.1.12.8.1.3.1.48	VlanId	read-only	This variable provides the Inner (second) VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
VLA ecpaTestStreamInnerVlan2Prio	1.3.6.1.4.1.2544.1.12.8.1.3.1.49	VlanPriority	read-only	This variable provides the Inner (second) VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
I32 ecpaTestStreamInnerVlan2EtherType	1.3.6.1.4.1.2544.1.12.8.1.3.1.50	Integer32	read-only	This variable provides the EtherType associated with the Inner (second) VLAN Tag. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
IP ecpaTestStreamDestIpV4Address	1.3.6.1.4.1.2544.1.12.8.1.3.1.51	IpAddress	read-only	This object provides the destination ipv4 IP Address for the test stream. This is valid when ecpaTestStreamIpVersion is ipv4.
ADR ecpaTestStreamDestIpV6Address	1.3.6.1.4.1.2544.1.12.8.1.3.1.52	Ipv6Address	read-only	This object provides the destination ipv6 IP Address for the test stream. This is valid when ecpaTestStreamIpVersion is ipv6.
T/F ecpaTestStreamConfigChanged	1.3.6.1.4.1.2544.1.12.8.1.3.1.53	TruthValue	read-only	This object provides information on whether the associated ecpaConfigStream is changed.
U32 ecpaTestStreamRateHi	1.3.6.1.4.1.2544.1.12.8.1.3.1.54	Unsigned32	read-write	The object enables specification of the higher 32 bits of the traffic generation rate.
esaProbeTable	1.3.6.1.4.1.2544.1.12.8.1.4		not-accessible	A list of entries corresponding to ESA Probes.
esaProbeEntry	1.3.6.1.4.1.2544.1.12.8.1.4.1		not-accessible	A row in the esaProbeTable. Entries can be created in this table by management application action. The slotIndex should be 255 if the product is cm5.1.
I32 esaProbeIndex	1.3.6.1.4.1.2544.1.12.8.1.4.1.1	Integer32	read-only	An integer index value used to uniquely identify this ESA Probe within a Card.
STR esaProbeName	1.3.6.1.4.1.2544.1.12.8.1.4.1.2	DisplayString	read-create	A unique identifier used by the Manager to distinguish the ESA Probe.
NUM esaProbeSourcePort	1.3.6.1.4.1.2544.1.12.8.1.4.1.3	VariablePointer	read-create	This object points to the Port to which the ESA Probe is attached, i.e.on which the service to be monitored resides.
NUM esaProbeAssocSchedGroup	1.3.6.1.4.1.2544.1.12.8.1.4.1.4	VariablePointer	read-only	This object points to the probe's associated Scheduled Group. Initially, when the probe is not associated with a Group, this object's value is set to {0.0}.
ESA esaProbeDirection	1.3.6.1.4.1.2544.1.12.8.1.4.1.5	EsaProbeDirection	read-create	This object allows to specify the direction of Probe traffic generation.
ESA esaProbeProtocol	1.3.6.1.4.1.2544.1.12.8.1.4.1.6	EsaProbeProtocol	read-create	Protocol to be used in ESA Probe messages. 'icmpTimestamp', 'icmpEcho', 'udpEcho' protocols support layer-3 ethernet service assurance. If the remote reflector is an ADVA equipment based on CM family of products, one-way loss measurement, one-way delay measurement, round-trip delay measurement and one-way jitter measurements are computed. Else, only round-trip delay measurements are applicable. 'y1731' protocol can be used for layer-2 ethernet service assurance. One-way loss measurement, one-way and round-trip delay measurement, and one-way jitter measurements are available for this protocol. 'y1731-slm-slr' protocol can be used for layer-2 ethernet service assurance using Synthetic Loss Measurement messages. One-way loss measurement, one-way and round-trip delay measurement, and one-way jitter measurements are available for this protocol.
IP esaProbeSrcIpAddress	1.3.6.1.4.1.2544.1.12.8.1.4.1.7	IpAddress	read-create	Variable that allows specification of the Probe's source IP Address. This IP Address is used in the IP header of the ESA Probe generated packets, as source address. NOTE: This attribute is not applicable to Y.1731 probes.
IP esaProbeSrcSubnetMask	1.3.6.1.4.1.2544.1.12.8.1.4.1.8	IpAddress	read-create	Variable that allows specification of the Probe's source IP Subnet Mask. NOTE: This attribute is not applicable to Y.1731 probes.
IP esaProbeDestIpAddress	1.3.6.1.4.1.2544.1.12.8.1.4.1.9	IpAddress	read-create	Variable that allows specification of the Reflector's destination IP Address. This IP Address is used in the IP header of the ESA Probe generated packets, as destination address. NOTE: This attribute is not applicable to Y.1731 probes.
NUM esaProbeSrcMep	1.3.6.1.4.1.2544.1.12.8.1.4.1.10	VariablePointer	read-create	This attribute is applicable only for Y.1731 probes. It identifies the source MEP that initiates the Y.1731 LMMs and DMMs.
MEP esaProbeDestMepType	1.3.6.1.4.1.2544.1.12.8.1.4.1.11	MepDestinationType	read-create	This attribute is applicable only for Y.1731 probes. This indicates if the destination MEP is specified using the MEP ID object esaProbeDestMepId.
MAC esaProbeDestMepMacAddr	1.3.6.1.4.1.2544.1.12.8.1.4.1.12	MacAddress	read-create	This attribute is applicable only for Y.1731 probes. It identifies the destination MEP that responds to the LMMs and DMMs. This MAC address will be the destination MAC address for LMM and DMM frames if esaProbeY1731DestMepType is 'macaddress'. If CC protocol is not enabled between source and destination MEP then this is the only choice to identify the remote MEP.
DOT esaProbeDestMepId	1.3.6.1.4.1.2544.1.12.8.1.4.1.13	Dot1agCfmMepIdOrZero	read-create	This attribute is applicable only for Y.1731 probes. It identifies the destination MEP that responds to the LMMs and DMMs. The MAC address of this RMEP ID from RMEP database will be the destination MAC address for LMM and DMM. This value is used only if the esaProbeY1731DestMepType is 'mepid'. CC protocol must be enabled between source and destination MEP if the RMEP ID is used to identify the Remote MEP.
T/F esaProbeVlanTagEnabled	1.3.6.1.4.1.2544.1.12.8.1.4.1.14	TruthValue	read-write	Ability to specify whether or not to use VLAN tagged or untagged ESA traffic generation on the Probe. NOTE: This attribute is not applicable to Y.1731 probes.
U32 esaProbeVlanTagEtherType	1.3.6.1.4.1.2544.1.12.8.1.4.1.15	Unsigned32	read-write	This variable allows the user to specify the monitored service's VLAN tag Ether Type. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
VLA esaProbeVlanId	1.3.6.1.4.1.2544.1.12.8.1.4.1.16	VlanId	read-write	This variable allows the user to specify the monitored service's VLAN tag. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
VLA esaProbeVlanPrio	1.3.6.1.4.1.2544.1.12.8.1.4.1.17	VlanPriority	read-write	This variable allows the user to specify the monitored service's VLAN priority. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
T/F esaProbeInnerVlanTagEnabled	1.3.6.1.4.1.2544.1.12.8.1.4.1.18	TruthValue	read-write	Ability to specify whether or not to use Inner VLAN tag. NOTE: This attribute is not applicable to Y.1731 probes.
U32 esaProbeInnerVlanTagEtherType	1.3.6.1.4.1.2544.1.12.8.1.4.1.19	Unsigned32	read-write	This variable allows the user to specify the monitored service's Inner VLAN tag Ether Type. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
VLA esaProbeInnerVlanId	1.3.6.1.4.1.2544.1.12.8.1.4.1.20	VlanId	read-write	This variable allows the user to specify the monitored service's Inner VLAN tag. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
VLA esaProbeInnerVlanPrio	1.3.6.1.4.1.2544.1.12.8.1.4.1.21	VlanPriority	read-write	This variable allows the user to specify the monitored service's Inner VLAN priority. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
IPP esaProbeIpPrioMapMode	1.3.6.1.4.1.2544.1.12.8.1.4.1.22	IpPriorityMapMode	read-write	This object enables specification of Priority Mapping Mode for the ESA Probe. NOTE: This attribute is not applicable to Y.1731 probes.
I32 esaProbeIpPriority	1.3.6.1.4.1.2544.1.12.8.1.4.1.23	Integer32	read-write	This object enables specification of Priority Value for esaProbePrioMapMode as priomap-tos,priomap-dscp. NOTE: This attribute is not applicable to Y.1731 probes.
I32 esaProbePktsPerSample	1.3.6.1.4.1.2544.1.12.8.1.4.1.24	Integer32	read-write	This object enables specification of number of packets within a sample run for ESA traffic generation. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
I32 esaProbePktSize	1.3.6.1.4.1.2544.1.12.8.1.4.1.25	Integer32	read-write	This object enables specification of fixed length frame size in bytes for ESA traffic generation. If not specified, default value of 104 bytes is used. NOTE: This attribute is not available to Y.1731 probes.
I32 esaProbeInterPktGap	1.3.6.1.4.1.2544.1.12.8.1.4.1.26	Integer32	read-write	This object enables specification of interval in milliseconds between packet generation. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
I32 esaProbePktDeadInterval	1.3.6.1.4.1.2544.1.12.8.1.4.1.27	Integer32	read-write	This object enables specification of the dead interval in seconds after 'esaProbePktsPerSample' have been generated within the sample. This allows for settling time of the ESA traffic. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
I32 esaProbeResponseTimeout	1.3.6.1.4.1.2544.1.12.8.1.4.1.28	Integer32	read-write	This object allows specification of the timeout value to determine lost packets. Time specified in seconds. NOTE: This attribute is not applicable to Y.1731 probes. This object is applicable to Layer 3 and SLM/SLR Probes.
I32 esaProbeY1731DmmPktSize	1.3.6.1.4.1.2544.1.12.8.1.4.1.29	Integer32	read-write	This object is only applicable to Y.1731 probes. This object enables specification of the TLV size for Delay Measurement Frames (DMMs). Value of 0 is a read-only value when the Probe protocol is not y1731. GE206 Release 4.4.x supports 2000 bytes
NUM esaProbeY1731LmmInterval	1.3.6.1.4.1.2544.1.12.8.1.4.1.30	EsaProbePktIntervalType	read-create	LMM frame transmission period. For Loss Measurement Frames, only interval-1sec is supported. This attribute is only applicable to Y.1731 probes.
NUM esaProbeY1731DmmInterval	1.3.6.1.4.1.2544.1.12.8.1.4.1.31	EsaProbePktIntervalType	read-create	DMM frame transmission period. This attribute is only applicable to Y.1731 probes.
I32 esaProbeHistoryBins	1.3.6.1.4.1.2544.1.12.8.1.4.1.32	Integer32	read-write	This object allows specification of number of history bins. This is the total history data that will be maintained for an ESA Probe run, at any instance.
NUM esaProbeHistoryInterval	1.3.6.1.4.1.2544.1.12.8.1.4.1.33	EsaProbeHistoryIntervalType	read-write	This object allows specification of the history interval period.
I32 esaProbeDistHistoryBins	1.3.6.1.4.1.2544.1.12.8.1.4.1.34	Integer32	read-write	This object allows specification of number of distribution history bins. This is the total history distribution data that will be maintained for an ESA Probe run, at any instance.
NUM esaProbeDistHistoryInterval	1.3.6.1.4.1.2544.1.12.8.1.4.1.35	EsaProbeHistoryIntervalType	read-write	This object allows specification of the history distribution interval period.
DAT esaProbeCreationTime	1.3.6.1.4.1.2544.1.12.8.1.4.1.36	DateAndTime	read-only	This object provides the creation time of the ESA Probe.
STO esaProbeStorageType	1.3.6.1.4.1.2544.1.12.8.1.4.1.37	StorageType	read-create	The type of storage configured for this entry.
ROW esaProbeRowStatus	1.3.6.1.4.1.2544.1.12.8.1.4.1.38	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeRowStatus object may be modified if the associated instance of this object is equal to active(1).
T/F esaProbeMultiCOSEnabled	1.3.6.1.4.1.2544.1.12.8.1.4.1.39	TruthValue	read-create	This object is introduced for FSP150CC Release 4.3. This object is only applicable for Y.1731 and SLM-SLR Probe Protocol Types. This object can be used to specify the multiple class of services (COS) for each ESA Probe.
ESA esaProbeSLAMonitorType	1.3.6.1.4.1.2544.1.12.8.1.4.1.40	EsaProbeSLAMonitorType	read-create	This object indicates whether the Probe is a point-to-point type or a point-to-multipoint type. Only SLM-SLR probes can be point-to-multipoint.
CLA esaProbeCOSType	1.3.6.1.4.1.2544.1.12.8.1.4.1.41	ClassOfServiceType	read-create	This object can be used to specify the first Class of Service associated with the Y.1731/SLM-SLR ESA Probe. In the case of a multiCOS Probe, this object has no semantics when multiple COS levels exist. This object is only valid for Y.1731/SLM-SLR ESA Probes.
T/F esaProbeSLMMulticastMACEnabled	1.3.6.1.4.1.2544.1.12.8.1.4.1.42	TruthValue	read-create	This object can be used to specify whether the SLM/SLR protocol Probe will use multicast MAC address in SLM (Synthetic Loss Measurement) messages. This object is only valid for SLM-SLR ESA Probes.
NUM esaProbeSOAMInterval	1.3.6.1.4.1.2544.1.12.8.1.4.1.43	EsaProbePktIntervalType	read-create	This object can be used to specify the packet interval type for Y.1731 LM/DM and SLM/SLR based ESA Probes, for the first Class of Service. In the case of a multiCOS Probe, this object has no semantics when multiple COS levels exist. This attribute is applicable for Y.1731 LM/DM and SLM/SLR based probes.
I32 esaProbeSOAMPktSize	1.3.6.1.4.1.2544.1.12.8.1.4.1.44	Integer32	read-write	This object can be used to specify the packet size for SLM-SLR based ESA Probes, for the first Class of Service. In the case of multiCOS Probe, this object has no semantics when multiple COS levels exist. In such cases this will return a value of 0.
T/F esaProbeInner2VlanTagEnabled	1.3.6.1.4.1.2544.1.12.8.1.4.1.45	TruthValue	read-write	Ability to specify whether or not to use Inner2 VLAN tag. NOTE: This attribute is not applicable to Y.1731 probes.
U32 esaProbeInner2VlanTagEtherType	1.3.6.1.4.1.2544.1.12.8.1.4.1.46	Unsigned32	read-write	This variable allows the user to specify the monitored service's Inner2 VLAN tag Ether Type. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
VLA esaProbeInner2VlanId	1.3.6.1.4.1.2544.1.12.8.1.4.1.47	VlanId	read-write	This variable allows the user to specify the monitored service's Inner2 VLAN tag. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
VLA esaProbeInner2VlanPrio	1.3.6.1.4.1.2544.1.12.8.1.4.1.48	VlanPriority	read-write	This variable allows the user to specify the monitored service's Inner2 VLAN priority. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
ADM esaProbeAdminState	1.3.6.1.4.1.2544.1.12.8.1.4.1.49	AdminState	read-only	This object represents the Administrative State of the ESA Probe. This is not externally managed.
OPE esaProbeOperationalState	1.3.6.1.4.1.2544.1.12.8.1.4.1.50	OperationalState	read-only	This object represents the Operational State of the ESA Probe.
SEC esaProbeSecondaryState	1.3.6.1.4.1.2544.1.12.8.1.4.1.51	SecondaryState	read-only	This object represents the Secondary State of the ESA Probe.
MAC esaProbeMacAddress	1.3.6.1.4.1.2544.1.12.8.1.4.1.52	MacAddress	read-only	This attribute is applicable only for Y.1731 probes. It identifies the destination MacAddress which esa using
STR esaProbeAlias	1.3.6.1.4.1.2544.1.12.8.1.4.1.53	DisplayString	read-create	This object allows SNMP management entities to provide an alias for an ESA Probe.
esaProbeScheduleGroupTable	1.3.6.1.4.1.2544.1.12.8.1.5		not-accessible	A list of entries that allow groups of ESA Probes to be scheduled.
esaProbeScheduleGroupEntry	1.3.6.1.4.1.2544.1.12.8.1.5.1		not-accessible	A row in esaProbeScheduleGroupTable. Entries are created in this table by management application action.
I32 esaProbeScheduleGroupIndex	1.3.6.1.4.1.2544.1.12.8.1.5.1.1	Integer32	read-create	A unique index to distinguish the ESA Probe Schedule Group.
STR esaProbeScheduleGroupDescr	1.3.6.1.4.1.2544.1.12.8.1.5.1.2	DisplayString	read-create	Description of the probe schedule group.
STR esaProbeScheduleGroupProbeList	1.3.6.1.4.1.2544.1.12.8.1.5.1.3	DisplayString	read-create	A comma separated list of esaProbeName's, that will have the same schedule.
SCH esaProbeScheduleGroupType	1.3.6.1.4.1.2544.1.12.8.1.5.1.4	ScheduleType	read-create	This object allows to specify whether the ESA probe group schedule is 'one-shot' or 'periodic'. A 'one-shot' schedule executes only once and then stops. A 'periodic' schedule reoccurs every 'esaProbeScheduleGroupInterval' seconds and continues until explicitly stopped.
DAT esaProbeScheduleGroupStartTime	1.3.6.1.4.1.2544.1.12.8.1.5.1.5	DateAndTime	read-create	This object allows specification of the start time of the ESA Probe Group. Value of time less than current system time will equate to current time. When the system time reaches this configured time, the ESA Probe Group will be activated.
U32 esaProbeScheduleGroupDuration	1.3.6.1.4.1.2544.1.12.8.1.5.1.6	Unsigned32	read-create	This object allows specification of the duration in 'seconds' for ESA Probe Group run. Note that a value of 4294967295 means Duration as FOREVER. FOREVER value is only applicable to schedule type oneshot. The value 4294967295 cannot be used if schedule type is periodic.
U32 esaProbeScheduleGroupInterval	1.3.6.1.4.1.2544.1.12.8.1.5.1.7	Unsigned32	read-create	This object allows specification of the interval in 'seconds' between successive runs for ESA Probe Group. This variable is only valid if the 'esaProbeScheduleGroupType' is 'periodic'.
ESA esaProbeScheduleGroupAction	1.3.6.1.4.1.2544.1.12.8.1.5.1.8	EsaAction	read-write	This object allows to suspend/resume the ESA scheduled group.
SCH esaProbeScheduleGroupStatus	1.3.6.1.4.1.2544.1.12.8.1.5.1.9	SchedActivityStatus	read-only	This object indicates the current status of the ESA Probe Group.
STO esaProbeScheduleGroupStorageType	1.3.6.1.4.1.2544.1.12.8.1.5.1.10	StorageType	read-create	The type of storage configured for this entry.
ROW esaProbeScheduleGroupRowStatus	1.3.6.1.4.1.2544.1.12.8.1.5.1.11	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeScheduleGroupRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeScheduleGroupRowStatus object may be modified if the associated instance of this object is equal to active(1).
STR esaProbeScheduleGroupActionProbeList	1.3.6.1.4.1.2544.1.12.8.1.5.1.12	DisplayString	read-write	A comma separated list of esaProbeName's, if set esaProbeScheduleGroupAction as add or remove, they will be add or remove from esaProbeScheduleGroupProbeList.
esaReflectorTable	1.3.6.1.4.1.2544.1.12.8.1.6		not-accessible	A list of entries corresponding to ESA Reflectors. NOTE: There is no need to create reflectors for Y.1731 probes as the MEPs will respond by default.
esaReflectorEntry	1.3.6.1.4.1.2544.1.12.8.1.6.1		not-accessible	A row in the esaReflectorTable. Entries can be created in this table by management application action.
I32 esaReflectorIndex	1.3.6.1.4.1.2544.1.12.8.1.6.1.1	Integer32	read-create	A unique index to distinguish the ESA Reflector.
STR esaReflectorName	1.3.6.1.4.1.2544.1.12.8.1.6.1.2	DisplayString	read-create	A unique identifier to distinguish the ESA Reflector.
IP esaReflectorIpAddress	1.3.6.1.4.1.2544.1.12.8.1.6.1.3	IpAddress	read-create	This object allows specification of the Reflector's IP Address. Reflector listens for packets destined at this IP Address.
IP esaReflectorSubnetMask	1.3.6.1.4.1.2544.1.12.8.1.6.1.4	IpAddress	read-create	This object allows specification of the Reflector's IP Subnet mask.
NUM esaReflectorSourcePort	1.3.6.1.4.1.2544.1.12.8.1.6.1.5	VariablePointer	read-create	This object points to the Port to which the ESA Reflector is attached, i.e.on which the service to be monitored resides.
IPP esaReflectorIpPrioMapMode	1.3.6.1.4.1.2544.1.12.8.1.6.1.6	IpPriorityMapMode	read-write	This object enables specification of Priority Mapping Mode for the ESA Reflector.
I32 esaReflectorIpPriority	1.3.6.1.4.1.2544.1.12.8.1.6.1.7	Integer32	read-write	This object enables specification of Priority Value for esaReflectorPrioMapMode as priomap-tos,priomap-dscp.
ESA esaReflectorAction	1.3.6.1.4.1.2544.1.12.8.1.6.1.8	EsaAction	read-write	This object allows to suspend/resume the ESA reflector.
T/F esaReflectorSuspended	1.3.6.1.4.1.2544.1.12.8.1.6.1.9	TruthValue	read-only	This object indicates whether the ESA Reflector is active or suspended.
DAT esaReflectorCreationTime	1.3.6.1.4.1.2544.1.12.8.1.6.1.10	DateAndTime	read-only	This object provides the creation time of the ESA Reflector.
STO esaReflectorStorageType	1.3.6.1.4.1.2544.1.12.8.1.6.1.11	StorageType	read-create	The type of storage configured for this entry.
ROW esaReflectorRowStatus	1.3.6.1.4.1.2544.1.12.8.1.6.1.12	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaReflectorRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaReflectorRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaReflectorRowStatus object may be modified if the associated instance of this object is equal to active(1).
ESA esaReflectorDirection	1.3.6.1.4.1.2544.1.12.8.1.6.1.13	EsaReflectorDirection	read-create	This object provides the direction of the ESA Reflector.
ADM esaReflectorAdminState	1.3.6.1.4.1.2544.1.12.8.1.6.1.14	AdminState	read-only	This object represents the Administrative State of the ESA Reflector. This is not externally managed.
OPE esaReflectorOperationalState	1.3.6.1.4.1.2544.1.12.8.1.6.1.15	OperationalState	read-only	This object represents the Operational State of the ESA Reflector.
SEC esaReflectorSecondaryState	1.3.6.1.4.1.2544.1.12.8.1.6.1.16	SecondaryState	read-only	This object represents the Secondary State of the ESA Reflector.
MAC esaReflectorMacAddress	1.3.6.1.4.1.2544.1.12.8.1.6.1.17	MacAddress	read-only	This attribute is applicable only for Y.1731 probes. It identifies the destination MacAddress which esa using
STR esaReflectorAlias	1.3.6.1.4.1.2544.1.12.8.1.6.1.18	DisplayString	read-create	This object allows SNMP management entities to provide an alias for an ESA Reflector.
esaProbeStatsTable	1.3.6.1.4.1.2544.1.12.8.1.7		not-accessible	A collection of ESA Probe related statistics kept for a particular ESA Probe entity. These reflect the current data.
esaProbeStatsEntry	1.3.6.1.4.1.2544.1.12.8.1.7.1		not-accessible	A conceptual row in the esaProbeStatsTable. An entry exists in this table for each ESA Probe.
I32 esaProbeStatsDestinationIndex	1.3.6.1.4.1.2544.1.12.8.1.7.1.1	Integer32	read-only	An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
I32 esaProbeStatsCOSIndex	1.3.6.1.4.1.2544.1.12.8.1.7.1.2	Integer32	read-only	An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
I32 esaProbeStatsIndex	1.3.6.1.4.1.2544.1.12.8.1.7.1.3	Integer32	read-only	An arbitrary integer index value used to uniquely identify this ESA Probe statistics entry. Index 1 corresponds to current and index 2 to rollover.
NUM esaProbeStatsIntervalType	1.3.6.1.4.1.2544.1.12.8.1.7.1.4	EsaProbePmIntervalType	read-only	Indicates the type of collection, i.e. whether it is current, or rollover.
CLA esaProbeStatsCOS	1.3.6.1.4.1.2544.1.12.8.1.7.1.5	ClassOfServiceType	read-only	The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
T/F esaProbeStatsValid	1.3.6.1.4.1.2544.1.12.8.1.7.1.6	TruthValue	read-only	Indicates the validity of the bin.
CMP esaProbeStatsAction	1.3.6.1.4.1.2544.1.12.8.1.7.1.7	CmPmBinAction	read-write	Allows the Manager to clear the bin.
NUM esaProbeStatsP2RPkts	1.3.6.1.4.1.2544.1.12.8.1.7.1.8	PerfCounter64	read-only	The total number of Transmitted Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeStatsR2PPkts.
NUM esaProbeStatsP2RErredPkts	1.3.6.1.4.1.2544.1.12.8.1.7.1.9	PerfCounter64	read-only	The total number of Packets in the current interval, for which there was a problem in transmission. This error is counted when there is a failure in packet transmission due to resource limitations (buffers). This can happen if the Probe Configuration was changed to send in a large number of packets in a time interval. NOTE: This is not applicable for Y.1731 probes.
NUM esaProbeStatsP2RSyncErrs	1.3.6.1.4.1.2544.1.12.8.1.7.1.10	PerfCounter64	read-only	The number of (time) Synchronization Errors from probe to reflector in the current interval.
NUM esaProbeStatsP2RLostPkts	1.3.6.1.4.1.2544.1.12.8.1.7.1.11	PerfCounter64	read-only	The number of Lost Pkts from probe to reflector in the current interval. For Y.1731 probes, these are the actual data frames lost.
NUM esaProbeStatsR2PPkts	1.3.6.1.4.1.2544.1.12.8.1.7.1.12	PerfCounter64	read-only	The total number of Received Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeStatsP2RPkts.
NUM esaProbeStatsR2PErredPkts	1.3.6.1.4.1.2544.1.12.8.1.7.1.13	PerfCounter64	read-only	The total number of Received Packets in the current interval, which had errors such as length of received packet is less than the protocol header length, packet was received after it was marked as lost (i.e.beyond timeout). NOTE: This is not applicable for Y.1731 probes.
NUM esaProbeStatsR2PSyncErrs	1.3.6.1.4.1.2544.1.12.8.1.7.1.14	PerfCounter64	read-only	The number of (time) Synchronization Errors from reflector to probe in the current interval.
NUM esaProbeStatsR2PLostPkts	1.3.6.1.4.1.2544.1.12.8.1.7.1.15	PerfCounter64	read-only	The number of Lost Pkts from reflector to probe in the current interval. For Y.1731 probes, these are the actual data frames lost.
NUM esaProbeStatsLostPkts	1.3.6.1.4.1.2544.1.12.8.1.7.1.16	PerfCounter64	read-only	The total number of Lost Packets in the current interval. Packets which are not received from the reflector end beyond the configured timeout value are termed as lost. NOTE: This is not applicable for Y.1731 probes.
NUM esaProbeStatsSeqGaps	1.3.6.1.4.1.2544.1.12.8.1.7.1.17	PerfCounter64	read-only	The total number of sequence gaps across all packets received in the current interval. If (Received Seq Number) is greater than or equal to (Last Received Seq Number + 2)) it is termed as a sequence gap. NOTE: This is not applicable for Y.1731 probes.
NUM esaProbeStatsOutOfSeqErrs	1.3.6.1.4.1.2544.1.12.8.1.7.1.18	PerfCounter64	read-only	The total number of out of sequence errors across all packets received in the current interval. If (Received Seq Number) is less than or equal to (Last Received Seq Number), it is termed as out of sequence error. NOTE: This is not applicable for Y.1731 probes.
U32 esaProbeStatsMinRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.19	Unsigned32	read-only	The minimum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
U32 esaProbeStatsMaxRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.20	Unsigned32	read-only	The maximum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
U32 esaProbeStatsAvgRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.21	Unsigned32	read-only	The average round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
NUM esaProbeStatsSumRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.22	PerfCounter64	read-only	The total sum of round trip delay(in microseconds) in the current interval. The reflector's processing time is excluded from the value.
NUM esaProbeStatsSumOfSqRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.23	PerfCounter64	read-only	The sum of square of round trip delays in the current interval.
U32 esaProbeStatsMinOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.24	Unsigned32	read-only	The minimum one-way source to destination delay(in microseconds) across all packets received in the current interval.
U32 esaProbeStatsMaxOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.25	Unsigned32	read-only	The maximum one-way source to destination delay(in microseconds) across all packets received in the current interval.
U32 esaProbeStatsAvgOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.26	Unsigned32	read-only	The average one-way source to destination delay(in microseconds) across all packets received in the current interval.
NUM esaProbeStatsSumOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.27	PerfCounter64	read-only	The total sum of one-way delay from source to destination in the current interval.
NUM esaProbeStatsSumOfSqOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.28	PerfCounter64	read-only	The sum of square of one-way delay from source to destination in the current interval.
U32 esaProbeStatsMinOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.29	Unsigned32	read-only	The minimum one-way destination to source delay(in microseconds) across all packets received in the current interval.
U32 esaProbeStatsMaxOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.30	Unsigned32	read-only	The maximum one-way destination to source delay(in microseconds) across all packets received in the current interval.
U32 esaProbeStatsAvgOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.31	Unsigned32	read-only	The average one-way destination to source delay(in microseconds) across all packets received in the current interval.
NUM esaProbeStatsSumOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.32	PerfCounter64	read-only	The total sum of one-way delay from destination to source in the current interval.
NUM esaProbeStatsSumOfSqOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.7.1.33	PerfCounter64	read-only	The sum of square of one-way delay from destination to source in the current interval.
U32 esaProbeStatsMinPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.34	Unsigned32	read-only	The minimum positive one-way jitter from source to destination in the current interval.
U32 esaProbeStatsMaxPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.35	Unsigned32	read-only	The maximum positive one-way jitter from source to destination in the current interval.
NUM esaProbeStatsNumPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.36	PerfCounter64	read-only	The total number of positive one-way jitters from source to destination in the current interval.
NUM esaProbeStatsSumPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.37	PerfCounter64	read-only	The total sum of positive one-way jitters from source to destination in the current interval.
NUM esaProbeStatsSumOfSqPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.38	PerfCounter64	read-only	The sum of square of positive one-way jitters from source to destination in the current interval.
U32 esaProbeStatsMinNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.39	Unsigned32	read-only	The minimum negative one-way jitter from source to destination in the current interval.
U32 esaProbeStatsMaxNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.40	Unsigned32	read-only	The maximum negative one-way jitter from source to destination in the current interval.
NUM esaProbeStatsNumNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.41	PerfCounter64	read-only	The total number of negative one-way jitters from source to destination in the current interval.
NUM esaProbeStatsSumNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.42	PerfCounter64	read-only	The total sum of negative one-way jitters from source to destination in the current interval.
NUM esaProbeStatsSumOfSqNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.43	PerfCounter64	read-only	The sum of square of negative one-way jitters from source to destination in the current interval.
U32 esaProbeStatsMinPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.44	Unsigned32	read-only	The minimum positive one-way jitter from destination to source in the current interval.
U32 esaProbeStatsMaxPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.45	Unsigned32	read-only	The maximum positive one-way jitter from destination to source in the current interval.
NUM esaProbeStatsNumPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.46	PerfCounter64	read-only	The total number of positive one-way jitters from destination to source in the current interval.
NUM esaProbeStatsSumPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.47	PerfCounter64	read-only	The total sum of positive one-way jitters from destination to source in the current interval.
NUM esaProbeStatsSumOfSqPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.48	PerfCounter64	read-only	The sum of square of positive one-way jitters from destination to source in the current interval.
U32 esaProbeStatsMinNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.49	Unsigned32	read-only	The minimum negative one-way jitter from destination to source in the current interval.
U32 esaProbeStatsMaxNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.50	Unsigned32	read-only	The maximum negative one-way jitter from destination to source in the current interval.
NUM esaProbeStatsNumNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.51	PerfCounter64	read-only	The total number of negative one-way jitters from destination to source in the current interval.
NUM esaProbeStatsSumNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.52	PerfCounter64	read-only	The total sum of negative one-way jitters from destination to source in the current interval.
NUM esaProbeStatsSumOfSqNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.53	PerfCounter64	read-only	The sum of square of negative one-way jitters from destination to source in the current interval.
NUM esaProbeStatsY1731P2RNegLossOccurrences	1.3.6.1.4.1.2544.1.12.8.1.7.1.54	PerfCounter64	read-only	This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from Source MEP (Probe) to Destination MEP (Reflector). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
NUM esaProbeStatsY1731R2PNegLossOccurrences	1.3.6.1.4.1.2544.1.12.8.1.7.1.55	PerfCounter64	read-only	This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from to Destination MEP (Reflector) to Source MEP (Probe). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
T/F esaProbeStatsY1731RxLmSamples	1.3.6.1.4.1.2544.1.12.8.1.7.1.56	TruthValue	read-only	This attribute is only applicable to Y.1731 probes. This flag indicates that at least one loss measurement sample was received for this bin period (LMRs received). This is used by the user to differentiate between valid zero frame loss and not receiving any LMRs.
T/F esaProbeStatsY1731RxDmSamples	1.3.6.1.4.1.2544.1.12.8.1.7.1.57	TruthValue	read-only	This attribute is only applicable to Y.1731 probes. This flag indicates that at least one delay measurement sample was received for this bin period (DMRs received).
NUM esaProbeStatsY1731P2RFrames	1.3.6.1.4.1.2544.1.12.8.1.7.1.58	PerfCounter64	read-only	This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Source MEP (Probe) that are transmitted towards the Destination MEP (Reflector). Based on the configuration the MEP counts the data frames with: - MEP's LM TX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
NUM esaProbeStatsY1731R2PFrames	1.3.6.1.4.1.2544.1.12.8.1.7.1.59	PerfCounter64	read-only	This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Destination MEP (Reflector) that are transmitted towards the Source MEP (Probe). Based on the configuration the MEP counts the data frames with: - MEP's LM RX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
U32 esaProbeStatsAvgAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.60	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute P2R Jitter value. .
U32 esaProbeStatsAvgAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.61	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute R2P Jitter value. .
U32 esaProbeStatsMinAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.62	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute P2R Jitter value. .
U32 esaProbeStatsMinAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.63	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute R2P Jitter value. .
U32 esaProbeStatsMaxAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.64	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute P2R Jitter value. .
U32 esaProbeStatsMaxAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.65	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute R2P Jitter value. .
NUM esaProbeStatsNumAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.66	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute P2R Jitters.
NUM esaProbeStatsNumAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.67	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute R2P Jitters.
NUM esaProbeStatsSumAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.68	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute P2R Jitter values.
NUM esaProbeStatsSumAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.69	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute R2P Jitter values.
NUM esaProbeStatsSumOfSqAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.70	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute P2R Jitter values.
NUM esaProbeStatsSumOfSqAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.7.1.71	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute R2P Jitter values.
esaProbeHistoryTable	1.3.6.1.4.1.2544.1.12.8.1.8		not-accessible	A collection of ESA Probe related history kept for a particular ESA Probe entity. These reflect the current data.
esaProbeHistoryEntry	1.3.6.1.4.1.2544.1.12.8.1.8.1		not-accessible	A conceptual row in the esaProbeHistoryTable. An entry exists in this table for each ESA Probe.
I32 esaProbeHistoryDestinationIndex	1.3.6.1.4.1.2544.1.12.8.1.8.1.1	Integer32	read-only	An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
I32 esaProbeHistoryCOSIndex	1.3.6.1.4.1.2544.1.12.8.1.8.1.2	Integer32	read-only	An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
I32 esaProbeHistoryIndex	1.3.6.1.4.1.2544.1.12.8.1.8.1.3	Integer32	read-only	An arbitrary integer index value used to uniquely identify this ESA Probe statistics history entry.
DAT esaProbeHistoryTime	1.3.6.1.4.1.2544.1.12.8.1.8.1.4	DateAndTime	read-only	Indicates the time of history bin creation.
T/F esaProbeHistoryValid	1.3.6.1.4.1.2544.1.12.8.1.8.1.5	TruthValue	read-only	Indicates the validity of the bin.
CMP esaProbeHistoryAction	1.3.6.1.4.1.2544.1.12.8.1.8.1.6	CmPmBinAction	read-write	Allows the Manager to clear the bin.
CLA esaProbeHistoryCOS	1.3.6.1.4.1.2544.1.12.8.1.8.1.7	ClassOfServiceType	read-only	The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
NUM esaProbeHistoryP2RPkts	1.3.6.1.4.1.2544.1.12.8.1.8.1.8	PerfCounter64	read-only	The total number of Transmitted Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeHistoryR2PPkts.
NUM esaProbeHistoryP2RErredPkts	1.3.6.1.4.1.2544.1.12.8.1.8.1.9	PerfCounter64	read-only	The total number of Packets in the current interval, for which there was a problem in transmission. This error is counted when there is a failure in packet transmission due to resource limitations (buffers). This can happen if the Probe Configuration was changed to send in a large number of packets in a time interval. NOTE: This is not applicable for Y.1731 probes.
NUM esaProbeHistoryP2RSyncErrs	1.3.6.1.4.1.2544.1.12.8.1.8.1.10	PerfCounter64	read-only	The number of (time) Synchronization Errors from probe to reflector in the current interval.
NUM esaProbeHistoryP2RLostPkts	1.3.6.1.4.1.2544.1.12.8.1.8.1.11	PerfCounter64	read-only	The number of Lost Pkts from probe to reflector in the current interval. For Y.1731 probes, these are the actual data frames lost.
NUM esaProbeHistoryR2PPkts	1.3.6.1.4.1.2544.1.12.8.1.8.1.12	PerfCounter64	read-only	The total number of Received Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeHistoryP2RPkts.
NUM esaProbeHistoryR2PErredPkts	1.3.6.1.4.1.2544.1.12.8.1.8.1.13	PerfCounter64	read-only	The total number of Received Packets in the current interval, which had errors such as length of received packet is less than the protocol header length, packet was received after it was marked as lost (i.e.beyond timeout). NOTE: This is not applicable for Y.1731 probes.
NUM esaProbeHistoryR2PSyncErrs	1.3.6.1.4.1.2544.1.12.8.1.8.1.14	PerfCounter64	read-only	The number of (time) Synchronization Errors from reflector to probe in the current interval.
NUM esaProbeHistoryR2PLostPkts	1.3.6.1.4.1.2544.1.12.8.1.8.1.15	PerfCounter64	read-only	The number of Lost Pkts from reflector to probe in the current interval. For Y.1731 probes, these are the actual data frames lost.
NUM esaProbeHistoryLostPkts	1.3.6.1.4.1.2544.1.12.8.1.8.1.16	PerfCounter64	read-only	The total number of Lost Packets in the current interval. Packets which are not received from the reflector end beyond the configured timeout value are termed as lost. NOTE: This is not applicable for Y.1731 probes.
NUM esaProbeHistorySeqGaps	1.3.6.1.4.1.2544.1.12.8.1.8.1.17	PerfCounter64	read-only	The total number of sequence gaps across all packets received in the current interval. If (Received Seq Number) is greater than or equal to (Last Received Seq Number + 2)) it is termed as a sequence gap. NOTE: This is not applicable for Y.1731 probes.
NUM esaProbeHistoryOutOfSeqErrs	1.3.6.1.4.1.2544.1.12.8.1.8.1.18	PerfCounter64	read-only	The total number of out of sequence errors across all packets received in the current interval. If (Received Seq Number) is less than or equal to (Last Received Seq Number), it is termed as out of sequence error. NOTE: This is not applicable for Y.1731 probes.
U32 esaProbeHistoryMinRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.19	Unsigned32	read-only	The minimum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
U32 esaProbeHistoryMaxRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.20	Unsigned32	read-only	The maximum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
U32 esaProbeHistoryAvgRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.21	Unsigned32	read-only	The average round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
NUM esaProbeHistorySumRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.22	PerfCounter64	read-only	The total sum of round trip delay(in microseconds) in the current interval. The reflector's processing time is excluded from the value.
NUM esaProbeHistorySumOfSqRoundTripDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.23	PerfCounter64	read-only	The sum of square of round trip delays in the current interval.
U32 esaProbeHistoryMinOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.24	Unsigned32	read-only	The minimum one-way source to destination delay(in microseconds) across all packets received in the current interval.
U32 esaProbeHistoryMaxOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.25	Unsigned32	read-only	The maximum one-way source to destination delay(in microseconds) across all packets received in the current interval.
U32 esaProbeHistoryAvgOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.26	Unsigned32	read-only	The average one-way source to destination delay(in microseconds) across all packets received in the current interval.
NUM esaProbeHistorySumOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.27	PerfCounter64	read-only	The total sum of one-way delay from source to destination in the current interval.
NUM esaProbeHistorySumOfSqOnewayP2RDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.28	PerfCounter64	read-only	The sum of square of one-way delay from source to destination in the current interval.
U32 esaProbeHistoryMinOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.29	Unsigned32	read-only	The minimum one-way destination to source delay(in microseconds) across all packets received in the current interval.
U32 esaProbeHistoryMaxOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.30	Unsigned32	read-only	The maximum one-way destination to source delay(in microseconds) across all packets received in the current interval.
U32 esaProbeHistoryAvgOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.31	Unsigned32	read-only	The average one-way destination to source delay(in microseconds) across all packets received in the current interval.
NUM esaProbeHistorySumOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.32	PerfCounter64	read-only	The total sum of one-way delay from destination to source in the current interval.
NUM esaProbeHistorySumOfSqOnewayR2PDelay	1.3.6.1.4.1.2544.1.12.8.1.8.1.33	PerfCounter64	read-only	The sum of square of one-way delay from destination to source in the current interval.
U32 esaProbeHistoryMinPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.34	Unsigned32	read-only	The minimum positive one-way jitter from source to destination in the current interval.
U32 esaProbeHistoryMaxPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.35	Unsigned32	read-only	The maximum positive one-way jitter from source to destination in the current interval.
NUM esaProbeHistoryNumPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.36	PerfCounter64	read-only	The total number of positive one-way jitters from source to destination in the current interval.
NUM esaProbeHistorySumPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.37	PerfCounter64	read-only	The total sum of positive one-way jitters from source to destination in the current interval.
NUM esaProbeHistorySumOfSqPosP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.38	PerfCounter64	read-only	The sum of square of positive one-way jitters from source to destination in the current interval.
U32 esaProbeHistoryMinNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.39	Unsigned32	read-only	The minimum negative one-way jitter from source to destination in the current interval.
U32 esaProbeHistoryMaxNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.40	Unsigned32	read-only	The maximum negative one-way jitter from source to destination in the current interval.
NUM esaProbeHistoryNumNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.41	PerfCounter64	read-only	The total number of negative one-way jitters from source to destination in the current interval.
NUM esaProbeHistorySumNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.42	PerfCounter64	read-only	The total sum of negative one-way jitters from source to destination in the current interval.
NUM esaProbeHistorySumOfSqNegP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.43	PerfCounter64	read-only	The sum of square of negative one-way jitters from source to destination in the current interval.
U32 esaProbeHistoryMinPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.44	Unsigned32	read-only	The minimum positive one-way jitter from destination to source in the current interval.
U32 esaProbeHistoryMaxPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.45	Unsigned32	read-only	The maximum positive one-way jitter from destination to source in the current interval.
NUM esaProbeHistoryNumPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.46	PerfCounter64	read-only	The total number of positive one-way jitters from destination to source in the current interval.
NUM esaProbeHistorySumPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.47	PerfCounter64	read-only	The total sum of positive one-way jitters from destination to source in the current interval.
NUM esaProbeHistorySumOfSqPosR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.48	PerfCounter64	read-only	The sum of square of positive one-way jitters from destination to source in the current interval.
U32 esaProbeHistoryMinNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.49	Unsigned32	read-only	The minimum negative one-way jitter from destination to source in the current interval.
U32 esaProbeHistoryMaxNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.50	Unsigned32	read-only	The maximum negative one-way jitter from destination to source in the current interval.
NUM esaProbeHistoryNumNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.51	PerfCounter64	read-only	The total number of negative one-way jitters from destination to source in the current interval.
NUM esaProbeHistorySumNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.52	PerfCounter64	read-only	The total sum of negative one-way jitters from destination to source in the current interval.
NUM esaProbeHistorySumOfSqNegR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.53	PerfCounter64	read-only	The sum of square of negative one-way jitters from destination to source in the current interval.
NUM esaProbeHistoryY1731P2RNegLossOccurrences	1.3.6.1.4.1.2544.1.12.8.1.8.1.54	PerfCounter64	read-only	This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from Source MEP (Probe) to Destination MEP (Reflector). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
NUM esaProbeHistoryY1731R2PNegLossOccurrences	1.3.6.1.4.1.2544.1.12.8.1.8.1.55	PerfCounter64	read-only	This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from to Destination MEP (Reflector) to Source MEP (Probe). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
T/F esaProbeHistoryY1731RxLmSamples	1.3.6.1.4.1.2544.1.12.8.1.8.1.56	TruthValue	read-only	This attribute is only applicable to Y.1731 probes. This flag indicates that at least one loss measurement sample was received for this bin period (LMRs received). This is used by the user to differentiate between valid zero frame loss and not receiving any LMRs.
T/F esaProbeHistoryY1731RxDmSamples	1.3.6.1.4.1.2544.1.12.8.1.8.1.57	TruthValue	read-only	This attribute is only applicable to Y.1731 probes. This flag indicates that at least one delay measurement sample was received for this bin period (DMRs received).
NUM esaProbeHistoryY1731P2RFrames	1.3.6.1.4.1.2544.1.12.8.1.8.1.58	PerfCounter64	read-only	This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Source MEP (Probe) that are transmitted towards the Destination MEP (Reflector). Based on the configuration the MEP counts the data frames with: - MEP's LM TX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
NUM esaProbeHistoryY1731R2PFrames	1.3.6.1.4.1.2544.1.12.8.1.8.1.59	PerfCounter64	read-only	This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Destination MEP (Reflector) that are transmitted towards the Source MEP (Probe). Based on the configuration the MEP counts the data frames with: - MEP's LM RX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
U32 esaProbeHistoryAvgAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.60	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute P2R Jitter value. .
U32 esaProbeHistoryAvgAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.61	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute R2P Jitter value. .
U32 esaProbeHistoryMinAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.62	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute P2R Jitter value. .
U32 esaProbeHistoryMinAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.63	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute R2P Jitter value. .
U32 esaProbeHistoryMaxAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.64	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute P2R Jitter value. .
U32 esaProbeHistoryMaxAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.65	Unsigned32	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute R2P Jitter value. .
NUM esaProbeHistoryNumAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.66	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute P2R Jitters.
NUM esaProbeHistoryNumAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.67	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute R2P Jitters.
NUM esaProbeHistorySumAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.68	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute P2R Jitter values.
NUM esaProbeHistorySumAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.69	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute R2P Jitter values.
NUM esaProbeHistorySumOfSqAbsP2RJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.70	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute P2R Jitter values.
NUM esaProbeHistorySumOfSqAbsR2PJitter	1.3.6.1.4.1.2544.1.12.8.1.8.1.71	PerfCounter64	read-only	This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute R2P Jitter values.
esaProbeDistStatsConfigTable	1.3.6.1.4.1.2544.1.12.8.1.9		not-accessible	A list of entries that need to be configured in order to obtain statistical distribution of ESA Probe collected data.
esaProbeDistStatsConfigEntry	1.3.6.1.4.1.2544.1.12.8.1.9.1		not-accessible	A row in the esaProbeDistStatsConfigTable.
I32 esaProbeDistStatsConfigIndex	1.3.6.1.4.1.2544.1.12.8.1.9.1.1	Integer32	read-only	A unique index for each row. Each row corresponds to each enumeration type specified in EsaProbeDistStatsType.
ESA esaProbeDistStatsConfigType	1.3.6.1.4.1.2544.1.12.8.1.9.1.2	EsaProbeDistStatsType	read-only	Indicates whether the statistical distribution is for round-trip delay (rt-delay), one-way probe to reflector delay (oneway-p2rdelay), one-way reflector to probe delay(oneway-r2pdelay), probe to reflector jitter (oneway-p2rjitter) or one-way reflector to probe jitter (oneway-r2pjitter).
I32 esaProbeDistStatsConfigMinVal	1.3.6.1.4.1.2544.1.12.8.1.9.1.3	Integer32	read-write	Minimum sample value in distribution.
I32 esaProbeDistStatsConfigMaxVal	1.3.6.1.4.1.2544.1.12.8.1.9.1.4	Integer32	read-write	Maximum sample value in distribution.
U32 esaProbeDistStatsConfigNumBins	1.3.6.1.4.1.2544.1.12.8.1.9.1.5	Unsigned32	read-write	Number of distribution bins.
I32 esaProbeDistStatsConfigLowBoundOfBin1	1.3.6.1.4.1.2544.1.12.8.1.9.1.6	Integer32	read-write	The lower bound of the 1st bin.
I32 esaProbeDistStatsConfigLowBoundOfBin2	1.3.6.1.4.1.2544.1.12.8.1.9.1.7	Integer32	read-write	The lower bound of the 2nd bin.
I32 esaProbeDistStatsConfigLowBoundOfBin3	1.3.6.1.4.1.2544.1.12.8.1.9.1.8	Integer32	read-write	The lower bound of the 3rd bin.
I32 esaProbeDistStatsConfigLowBoundOfBin4	1.3.6.1.4.1.2544.1.12.8.1.9.1.9	Integer32	read-write	The lower bound of the 4th bin.
I32 esaProbeDistStatsConfigLowBoundOfBin5	1.3.6.1.4.1.2544.1.12.8.1.9.1.10	Integer32	read-write	The lower bound of the 5th bin.
I32 esaProbeDistStatsConfigLowBoundOfBin6	1.3.6.1.4.1.2544.1.12.8.1.9.1.11	Integer32	read-write	The lower bound of the 6th bin.
I32 esaProbeDistStatsConfigLowBoundOfBin7	1.3.6.1.4.1.2544.1.12.8.1.9.1.12	Integer32	read-write	The lower bound of the 7th bin.
I32 esaProbeDistStatsConfigLowBoundOfBin8	1.3.6.1.4.1.2544.1.12.8.1.9.1.13	Integer32	read-write	The lower bound of the 8th bin.
I32 esaProbeDistStatsConfigLowBoundOfBin9	1.3.6.1.4.1.2544.1.12.8.1.9.1.14	Integer32	read-write	The lower bound of the 9th bin.
esaProbeDistStatsTable	1.3.6.1.4.1.2544.1.12.8.1.10		not-accessible	A list of entries that provide statistical distribution of ESA Probe collected data.
esaProbeDistStatsEntry	1.3.6.1.4.1.2544.1.12.8.1.10.1		not-accessible	A row in the esaProbeDistStatsTable.
I32 esaProbeDistStatsDestinationIndex	1.3.6.1.4.1.2544.1.12.8.1.10.1.1	Integer32	read-only	An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
I32 esaProbeDistStatsCOSIndex	1.3.6.1.4.1.2544.1.12.8.1.10.1.2	Integer32	read-only	An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
CMP esaProbeDistStatsAction	1.3.6.1.4.1.2544.1.12.8.1.10.1.3	CmPmBinAction	read-write	Allows the Manager to clear the bin.
CLA esaProbeDistStatsCOS	1.3.6.1.4.1.2544.1.12.8.1.10.1.4	ClassOfServiceType	read-only	The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
I32 esaProbeDistStatsNumBins	1.3.6.1.4.1.2544.1.12.8.1.10.1.5	Integer32	read-only	Number of bins over which the statistical data is distributed.
NUM esaProbeDistStatsLTMin	1.3.6.1.4.1.2544.1.12.8.1.10.1.6	PerfCounter64	read-only	Number of sample data points which are less than the minimum value specified.
NUM esaProbeDistStatsGTMax	1.3.6.1.4.1.2544.1.12.8.1.10.1.7	PerfCounter64	read-only	Number of sample data points which are greater than the maximum value specified.
esaProbeDistStatsBinTable	1.3.6.1.4.1.2544.1.12.8.1.11		not-accessible	A list of entries that provide statistical distribution of ESA Probe collected data for specific BINs.
esaProbeDistStatsBinEntry	1.3.6.1.4.1.2544.1.12.8.1.11.1		not-accessible	A row in the esaProbeDistStatsBinTable.
I32 esaProbeDistStatsBinIndex	1.3.6.1.4.1.2544.1.12.8.1.11.1.1	Integer32	read-only	An index for each row that uniquely provides statistical data for a range.
I32 esaProbeDistStatsBinLower	1.3.6.1.4.1.2544.1.12.8.1.11.1.2	Integer32	read-only	The lower limit of values collected in this bin.
I32 esaProbeDistStatsBinUpper	1.3.6.1.4.1.2544.1.12.8.1.11.1.3	Integer32	read-only	The upper limit of values collected in this bin.
NUM esaProbeDistStatsBinNumSamples	1.3.6.1.4.1.2544.1.12.8.1.11.1.4	PerfCounter64	read-only	Number of sample data points which fall between the lower and upper limits.
esaProbeDistHistoryTable	1.3.6.1.4.1.2544.1.12.8.1.12		not-accessible	A list of entries that provide statistical distribution history of ESA Probe collected data.
esaProbeDistHistoryEntry	1.3.6.1.4.1.2544.1.12.8.1.12.1		not-accessible	A row in the esaProbeDistHistoryTable.
I32 esaProbeDistHistoryDestinationIndex	1.3.6.1.4.1.2544.1.12.8.1.12.1.1	Integer32	read-only	An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
I32 esaProbeDistHistoryCOSIndex	1.3.6.1.4.1.2544.1.12.8.1.12.1.2	Integer32	read-only	An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
I32 esaProbeDistHistoryIndex	1.3.6.1.4.1.2544.1.12.8.1.12.1.3	Integer32	read-only	An arbitrary integer index value used to uniquely identify this ESA Probe Distribution History entry.
DAT esaProbeDistHistoryTime	1.3.6.1.4.1.2544.1.12.8.1.12.1.4	DateAndTime	read-only	Indicates the time of history bin creation.
CMP esaProbeDistHistoryAction	1.3.6.1.4.1.2544.1.12.8.1.12.1.5	CmPmBinAction	read-write	Allows the Manager to clear the bin.
CLA esaProbeDistHistoryCOS	1.3.6.1.4.1.2544.1.12.8.1.12.1.6	ClassOfServiceType	read-only	The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
I32 esaProbeDistHistoryNumBins	1.3.6.1.4.1.2544.1.12.8.1.12.1.7	Integer32	read-only	Number of bins over which the statistical data is distributed.
NUM esaProbeDistHistoryLTMin	1.3.6.1.4.1.2544.1.12.8.1.12.1.8	PerfCounter64	read-only	Number of sample data points which are less than the minimum value specified.
NUM esaProbeDistHistoryGTMax	1.3.6.1.4.1.2544.1.12.8.1.12.1.9	PerfCounter64	read-only	Number of sample data points which are greater than the maximum value specified.
esaProbeDistHistoryBinTable	1.3.6.1.4.1.2544.1.12.8.1.13		not-accessible	A list of entries that provide historical statistical distribution of ESA Probe collected data for specific BINs.
esaProbeDistHistoryBinEntry	1.3.6.1.4.1.2544.1.12.8.1.13.1		not-accessible	A row in the esaProbeDistHistoryBinTable.
I32 esaProbeDistHistoryBinIndex	1.3.6.1.4.1.2544.1.12.8.1.13.1.1	Integer32	read-only	An index for each row that uniquely provides statistical data for a range.
I32 esaProbeDistHistoryBinLower	1.3.6.1.4.1.2544.1.12.8.1.13.1.2	Integer32	read-only	The lower limit of values collected in this bin.
I32 esaProbeDistHistoryBinUpper	1.3.6.1.4.1.2544.1.12.8.1.13.1.3	Integer32	read-only	The upper limit of values collected in this bin.
NUM esaProbeDistHistoryBinNumSamples	1.3.6.1.4.1.2544.1.12.8.1.13.1.4	PerfCounter64	read-only	Number of sample data points which fall between the lower and upper limits.
esaProbeStatsThresholdTable	1.3.6.1.4.1.2544.1.12.8.1.14		not-accessible	A table of entries that allow manageability of ESA Probe Thresholds.
esaProbeStatsThresholdEntry	1.3.6.1.4.1.2544.1.12.8.1.14.1		not-accessible	A conceptual row in the esaProbeStatsThresholdTable.
I32 esaProbeStatsThresholdIndex	1.3.6.1.4.1.2544.1.12.8.1.14.1.1	Integer32	read-only	An index that uniquely identifies an entry in the esaProbeStatsThresholdTable.
NUM esaProbeStatsThresholdVariable	1.3.6.1.4.1.2544.1.12.8.1.14.1.2	VariablePointer	read-only	The object identifier of the particular variable to be sampled. Objects of the esaProbeStatsTable table are monitored. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, PerfCounter64, Gauge, or TimeTicks) may be sampled.
U32 esaProbeStatsThresholdAbsValueLo	1.3.6.1.4.1.2544.1.12.8.1.14.1.3	Unsigned32	read-write	Lower 32 bits of the absolute value of the threshold.
U32 esaProbeStatsThresholdAbsValueHi	1.3.6.1.4.1.2544.1.12.8.1.14.1.4	Unsigned32	read-write	Higher 32 bits of the absolute value of the threshold.
NUM esaProbeStatsThresholdMonValue	1.3.6.1.4.1.2544.1.12.8.1.14.1.5	PerfCounter64	read-only	Monitored value corresponding to esaProbeStatsThresholdVariable.
esaProbeCOSConfigTable	1.3.6.1.4.1.2544.1.12.8.1.15		not-accessible	A list of entries corresponding to ESA Probes COS Configuration Levels.
esaProbeCOSConfigEntry	1.3.6.1.4.1.2544.1.12.8.1.15.1		not-accessible	A row in the esaProbeCOSConfigTable. Entries can be created in this table by management application action.
I32 esaProbeCOSConfigIndex	1.3.6.1.4.1.2544.1.12.8.1.15.1.1	Integer32	read-create	An integer index value used to uniquely identify SLA (Service Level Agreement) for a specific Class of Service. Index 1 is associated with cos-0, index 2 with cos-1, index 3 with cos-2 and so on.
CLA esaProbeCOSConfigType	1.3.6.1.4.1.2544.1.12.8.1.15.1.2	ClassOfServiceType	read-create	This is the Class of Service Type for Y.1731/SLM-SLR Probes, associated with the row.
NUM esaProbeCOSConfigInterval	1.3.6.1.4.1.2544.1.12.8.1.15.1.3	EsaProbePktIntervalType	read-create	This is the Class of Service Y.1731/SLM-SLR packet interval type.
I32 esaProbeCOSConfigPktSize	1.3.6.1.4.1.2544.1.12.8.1.15.1.4	Integer32	read-create	This is the Class of Service Y.1731/SLM-SLR Packet Size. This object enables specification of the TLV size for Delay Measurement Measures(DMMs) as well as Synthetic Loss Measurement Frames (SLMs).
STO esaProbeCOSConfigStorageType	1.3.6.1.4.1.2544.1.12.8.1.15.1.5	StorageType	read-create	The type of storage configured for this entry.
ROW esaProbeCOSConfigRowStatus	1.3.6.1.4.1.2544.1.12.8.1.15.1.6	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeCOSConfigRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeCOSConfigRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeCOSConfigRowStatus object may be modified if the associated instance of this object is equal to active(1).
NUM esaProbeCOSConfigslmInterval	1.3.6.1.4.1.2544.1.12.8.1.15.1.7	EsaProbePktIntervalType	read-create	This allows specification of the interval between subsequent SLM packets.
I32 esaProbeCOSConfigslmPktSize	1.3.6.1.4.1.2544.1.12.8.1.15.1.8	Integer32	read-create	This allows specification of the SLM Packet Size.
U32 esaProbeCOSConfigSoamPmExtAvailFlrThreshold	1.3.6.1.4.1.2544.1.12.8.1.15.1.9	Unsigned32	read-write	Frame loss ratio threshold for Availability (m%).
U32 esaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus	1.3.6.1.4.1.2544.1.12.8.1.15.1.10	Unsigned32	read-write	This is the number of loss measurement PDUs. delta_t is this attribute multiplied by the loss measurement message period. For example, if SLM message period is 100ms and this attribute is 10, then the delta_t is 1second.
U32 esaProbeCOSConfigSoamPmExtConDeltaTsForAvail	1.3.6.1.4.1.2544.1.12.8.1.15.1.11	Unsigned32	read-write	This is the number of consecutive delta_ts used in the computation of availability/unavailability (n).
esaProbeMultiDestinationTable	1.3.6.1.4.1.2544.1.12.8.1.16		not-accessible	A list of entries corresponding to ESA Probes Multi Destinations.
esaProbeMultiDestinationEntry	1.3.6.1.4.1.2544.1.12.8.1.16.1		not-accessible	A row in the esaProbeMultiDestinationTable. Entries can be created in this table by management application action. Entries in this table represent destinations in a point-to-multipoint ESA Probe.
I32 esaProbeDestinationIndex	1.3.6.1.4.1.2544.1.12.8.1.16.1.1	Integer32	read-create	An integer index value used to uniquely identify a destination.
MEP esaProbeDestinationMepType	1.3.6.1.4.1.2544.1.12.8.1.16.1.2	MepDestinationType	read-create	This attribute is applicable only for point-to-multipoint probes. This indicates if the destination MEP is specified using the MEP ID object esaProbeDestinationMepId.
MAC esaProbeDestinationMepMacAddr	1.3.6.1.4.1.2544.1.12.8.1.16.1.3	MacAddress	read-create	This attribute is applicable only for point-to-multipoint probes. It identifies the destination MEP. This MAC address will be the destination MAC address for frames if esaProbeDestinationMepType is 'macaddress'. If CC protocol is not enabled between source and destination MEP then this is the only choice to identify the remote MEP.
DOT esaProbeDestinationMepId	1.3.6.1.4.1.2544.1.12.8.1.16.1.4	Dot1agCfmMepIdOrZero	read-create	This attribute is applicable only for point-to-multipoint probes. It identifies the destination MEP. The MAC address of this RMEP ID from RMEP database will be the destination MAC address. This value is used only if the esaProbeDestinationMepType is 'mepid'. CC protocol must be enabled between source and destination MEP if the RMEP ID is used to identify the Remote MEP.
STO esaProbeDestinationStorageType	1.3.6.1.4.1.2544.1.12.8.1.16.1.5	StorageType	read-create	The type of storage configured for this entry.
ROW esaProbeDestinationRowStatus	1.3.6.1.4.1.2544.1.12.8.1.16.1.6	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeDestinationRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeDestinationRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeDestinationRowStatus object may be modified if the associated instance of this object is equal to active(1).
bertControlTable	1.3.6.1.4.1.2544.1.12.8.1.17		not-accessible	A list of entries for the control of BERT Streams.
bertControlEntry	1.3.6.1.4.1.2544.1.12.8.1.17.1		not-accessible	A conceptual row in the bertControlTable.
I32 bertControlIndex	1.3.6.1.4.1.2544.1.12.8.1.17.1.1	Integer32	not-accessible	An arbitrary integer index value used to uniquely identify this BERT Control.
NUM bertControlSourceEntity	1.3.6.1.4.1.2544.1.12.8.1.17.1.2	VariablePointer	read-write	Pointer to the entity on which the BERT will be started within a card.
BER bertControlTestMode	1.3.6.1.4.1.2544.1.12.8.1.17.1.3	BerTestMode	read-write	The mode of BERT to be performed.
I32 bertControlDuration	1.3.6.1.4.1.2544.1.12.8.1.17.1.4	Integer32	read-write	This object enables specification of the time in seconds for BERT. BERT will be stopped after the specified time interval is exhausted.
I32 bertControlStream	1.3.6.1.4.1.2544.1.12.8.1.17.1.5	Integer32	read-write	This object specifies which stream should be included in the BERT execution. Value of 0 indicates that no streams is selected by bertControlStream. Non 0 value indicates the selected BERT stream.
BER bertControlAction	1.3.6.1.4.1.2544.1.12.8.1.17.1.6	BertControlAction	read-write	This object enables starting/stopping of traffic generation as well as resetting of monitored streams. This object may not be specified at configuration creation time - in this case it will take the value of `none'. This allows manager to explicitly control the start and stop of traffic generation/monitoring activity. Value of `stop' is invalid if the activity is specified but not started. Value of `start' is valid during creation time, as well as when activity is already stopped. Specification of `reset' resets the specified streams to default values, as well as clears the control specification. Get on this variable gives the most recent SNMP set specification.
BER bertControlTestStatus	1.3.6.1.4.1.2544.1.12.8.1.17.1.7	BerTestStatus	read-only	This object reflects the current status of test set configuration entry. Upon creation, the status has a value of `initial'; the status changes to `in-progress' upon ecpaControlAction indicating `start'; the status changes to `completed' upon ecpaControlAction indicating stop, as well as when the specified test generation completes autonomously upon completion of number of frames or completion of specified time interval.
bertConfigStreamTable	1.3.6.1.4.1.2544.1.12.8.1.18		not-accessible	A list of entries for the configuration of BERT Config Stream Specifications.
bertConfigStreamEntry	1.3.6.1.4.1.2544.1.12.8.1.18.1		not-accessible	A conceptual row in the bertConfigStreamTable.
I32 bertConfigStreamIndex	1.3.6.1.4.1.2544.1.12.8.1.18.1.1	Integer32	not-accessible	An arbitrary integer index value used to uniquely identify this BERT configStream.
STR bertConfigStreamName	1.3.6.1.4.1.2544.1.12.8.1.18.1.2	DisplayString	read-write	Symbolic Stream Name that can be associated with an BERT Config stream.
BER bertConfigStreamTxPattern	1.3.6.1.4.1.2544.1.12.8.1.18.1.3	BertPattern	read-write	Allows specification of the Tx pattern of this BERT Config stream.
T/F bertConfigStreamErrInjectEnabled	1.3.6.1.4.1.2544.1.12.8.1.18.1.4	TruthValue	read-write	This object allows specification of whether Bit Error be injected.
BIT bertConfigStreamErrInjectRate	1.3.6.1.4.1.2544.1.12.8.1.18.1.5	BitErrRate	read-write	Bit Error Rate, applicable when Error Injection is enabled.
I32 bertConfigStreamErrInjectRateMultiplier	1.3.6.1.4.1.2544.1.12.8.1.18.1.6	Integer32	read-write	BER value with 0.1 Step, in this release is fixed 10, only applicable when Error Injection is enabled.
BER bertConfigStreamUserPatternLength	1.3.6.1.4.1.2544.1.12.8.1.18.1.7	BertUserPatternLength	read-write	User defined testing pattern length.
STR bertConfigStreamUserPattern	1.3.6.1.4.1.2544.1.12.8.1.18.1.8	DisplayString	read-write	User defined testing pattern in a HEX format display string, applicable when test pattern is user defined.
bertTestStreamTable	1.3.6.1.4.1.2544.1.12.8.1.19		not-accessible	A list of entries containing results of a previous test.
bertTestStreamEntry	1.3.6.1.4.1.2544.1.12.8.1.19.1		not-accessible	A conceptual row in the bertTestStreamTable. Entries in this table show results of the current BERT.
I32 bertTestStreamIndex	1.3.6.1.4.1.2544.1.12.8.1.19.1.1	Integer32	not-accessible	An integer index value corresponding to the stream index for which the BERT was initiated.
STR bertTestStreamName	1.3.6.1.4.1.2544.1.12.8.1.19.1.2	DisplayString	read-write	Symbolic Stream Name that can be associated with an BERT stream.
BER bertTestStreamTxPattern	1.3.6.1.4.1.2544.1.12.8.1.19.1.3	BertPattern	read-only	Allows specification of the Tx pattern of this BERT Test stream.
T/F bertTestStreamErrInjectEnabled	1.3.6.1.4.1.2544.1.12.8.1.19.1.4	TruthValue	read-only	This object allows specification of whether Bit Error be injected.
BIT bertTestStreamErrInjectRate	1.3.6.1.4.1.2544.1.12.8.1.19.1.5	BitErrRate	read-only	Bit Error Rate, applicable when Error Injection is enabled.
I32 bertTestStreamErrInjectRateMultiplier	1.3.6.1.4.1.2544.1.12.8.1.19.1.6	Integer32	read-only	BER value with 0.1 Step, in this release is fixed 10, only applicable when Error Injection is enabled.
BER bertTestStreamUserPatternLength	1.3.6.1.4.1.2544.1.12.8.1.19.1.7	BertUserPatternLength	read-only	User defined testing pattern length.
STR bertTestStreamUserPattern	1.3.6.1.4.1.2544.1.12.8.1.19.1.8	DisplayString	read-only	User defined testing pattern in a HEX format display string, applicable when test pattern is user defined.
DAT bertTestStreamMonStartTime	1.3.6.1.4.1.2544.1.12.8.1.19.1.9	DateAndTime	read-only	The start time of the BERT for this stream.
DAT bertTestStreamMonEndTime	1.3.6.1.4.1.2544.1.12.8.1.19.1.10	DateAndTime	read-only	The end time of the BERT for this stream.
I32 bertTestStreamMonElapsedTime	1.3.6.1.4.1.2544.1.12.8.1.19.1.11	Integer32	read-only	The elapsed time of BERT for this stream in seconds.
BER bertTestStreamMonSyncState	1.3.6.1.4.1.2544.1.12.8.1.19.1.12	BertSyncState	read-only	The Sync State of the BERT.
BER bertTestStreamMonRxPattern	1.3.6.1.4.1.2544.1.12.8.1.19.1.13	BertPattern	read-only	Allows specification of the Rx pattern of this BERT Test stream.
U32 bertTestStreamMonSyncCounts	1.3.6.1.4.1.2544.1.12.8.1.19.1.14	Unsigned32	read-only	Allows specification of the Sync counts from test start.
NUM bertTestStreamMonRxBitErrsSinceStart	1.3.6.1.4.1.2544.1.12.8.1.19.1.15	PerfCounter64	read-only	Allows specification of the Received Errors since test start.
NUM bertTestStreamMonRxBitsSinceStart	1.3.6.1.4.1.2544.1.12.8.1.19.1.16	PerfCounter64	read-only	Allows specification of the Received Bits since test start.
U32 bertTestStreamMonRxESsSinceStart	1.3.6.1.4.1.2544.1.12.8.1.19.1.17	Unsigned32	read-only	Allows specification of the Error seconds since test start.
BIT bertTestStreamMonRxErrRateSinceStart	1.3.6.1.4.1.2544.1.12.8.1.19.1.18	BitErrRate	read-only	Allows specification of the Received BER Unit since test start.
I32 bertTestStreamMonRxErrRateMultiplierSinceStart	1.3.6.1.4.1.2544.1.12.8.1.19.1.19	Integer32	read-only	Allows specification of the Received BER value with 0.1 Step since test start.
NUM bertTestStreamMonRxBitErrsSinceLastSync	1.3.6.1.4.1.2544.1.12.8.1.19.1.20	PerfCounter64	read-only	Allows specification of the Received Errors since last sync.
NUM bertTestStreamMonRxBitsSinceLastSync	1.3.6.1.4.1.2544.1.12.8.1.19.1.21	PerfCounter64	read-only	Allows specification of the Received Bits since last sync.
U32 bertTestStreamMonRxESsSinceLastSync	1.3.6.1.4.1.2544.1.12.8.1.19.1.22	Unsigned32	read-only	Allows specification of the Received Error seconds since last sync.
BIT bertTestStreamMonRxErrRateSinceLastSync	1.3.6.1.4.1.2544.1.12.8.1.19.1.23	BitErrRate	read-only	Allows specification of the Received BER Unit since last sync.
U32 bertTestStreamMonRxErrRateMultiplierSinceLastSync	1.3.6.1.4.1.2544.1.12.8.1.19.1.24	Unsigned32	read-only	Allows specification of the Received BER value with 0.1 Step since last sync.
T/F bertTestStreamConfigChangedFlag	1.3.6.1.4.1.2544.1.12.8.1.19.1.25	TruthValue	read-only	This object provides information on whether the associated bertConfigStream is changed.
U32 bertTestStreamMonOOSSsSinceStart	1.3.6.1.4.1.2544.1.12.8.1.19.1.26	Unsigned32	read-only	This object means the Out of Sync Seconds since start.
f3EsaProbeCOSConfigSoamPmExtTable	1.3.6.1.4.1.2544.1.12.8.1.20		not-accessible	A list of entries corresponding to ESA Probe Cos Configurations MEF 35.
f3EsaProbeCOSConfigSoamPmExtEntry	1.3.6.1.4.1.2544.1.12.8.1.20.1		not-accessible	A row in the esaProbeCOSConfigTable MEF 35. Entries can be created in this table by management application action.
U32 f3EsaProbeCOSConfigSoamPmExtAvailFlrThreshold	1.3.6.1.4.1.2544.1.12.8.1.20.1.1	Unsigned32	read-write	Frame loss ratio threshold for Availability (m%).
U32 f3EsaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus	1.3.6.1.4.1.2544.1.12.8.1.20.1.2	Unsigned32	read-write	This is the number of loss measurement PDUs. delta_t is this attribute multiplied by the loss measurement message period. For example, if SLM message period is 100ms and this attribute is 10, then the delta_t is 1second.
U32 f3EsaProbeCOSConfigSoamPmExtConDeltaTsForAvail	1.3.6.1.4.1.2544.1.12.8.1.20.1.3	Unsigned32	read-write	This is the number of consecutive delta_ts used in the computation of availability/unavailability (n).
f3EsaProbeStatsSoamPmExtTable	1.3.6.1.4.1.2544.1.12.8.1.21		not-accessible	A collection of ESA Probe MEF 35 related statistics kept for a particular ESA Probe entity. These reflect the current data.
f3EsaProbeStatsSoamPmExtEntry	1.3.6.1.4.1.2544.1.12.8.1.21.1		not-accessible	A conceptual row in the f3EsaProbeStatsSoamPmExtTable.
NUM f3EsaProbeStatsSoamPmExtMinP2RFlr	1.3.6.1.4.1.2544.1.12.8.1.21.1.1	PerfCounter64	read-only	This is the minimum probe to reflector FLR (m%).
NUM f3EsaProbeStatsSoamPmExtMaxP2RFlr	1.3.6.1.4.1.2544.1.12.8.1.21.1.2	PerfCounter64	read-only	This is the maximum probe to reflector FLR (m%).
NUM f3EsaProbeStatsSoamPmExtAvgP2RFlr	1.3.6.1.4.1.2544.1.12.8.1.21.1.3	PerfCounter64	read-only	This is the average probe to reflector FLR (m%).
NUM f3EsaProbeStatsSoamPmExtMinR2PFlr	1.3.6.1.4.1.2544.1.12.8.1.21.1.4	PerfCounter64	read-only	This is the minimum reflector to probe FLR (m%).
NUM f3EsaProbeStatsSoamPmExtMaxR2PFlr	1.3.6.1.4.1.2544.1.12.8.1.21.1.5	PerfCounter64	read-only	This is the maximum reflector to probe FLR (m%).
NUM f3EsaProbeStatsSoamPmExtAvgR2PFlr	1.3.6.1.4.1.2544.1.12.8.1.21.1.6	PerfCounter64	read-only	This is the average reflector to probe FLR (m%).
NUM f3EsaProbeStatsSoamPmExtP2rSeverelyErroredDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.21.1.7	PerfCounter64	read-only	This is the number of delta_ts in which the FLR is greater than availability threshold in the probe to reflector direction.
NUM f3EsaProbeStatsSoamPmExtR2PSeverelyErroredDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.21.1.8	PerfCounter64	read-only	This is the number of delta_ts in which the FLR is greater than availability threshold in the reflector to probe direction.
NUM f3EsaProbeStatsSoamPmExtP2rAvailableTime	1.3.6.1.4.1.2544.1.12.8.1.21.1.9	PerfCounter64	read-only	This is the probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeStatsSoamPmExtR2PAvailableTime	1.3.6.1.4.1.2544.1.12.8.1.21.1.10	PerfCounter64	read-only	This is the reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeStatsSoamPmExtP2rUnavailableTime	1.3.6.1.4.1.2544.1.12.8.1.21.1.11	PerfCounter64	read-only	This is the probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeStatsSoamPmExtR2PUnavailableTime	1.3.6.1.4.1.2544.1.12.8.1.21.1.12	PerfCounter64	read-only	This is the reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeStatsSoamPmExtMinAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.21.1.13	PerfCounter64	read-only	Minimum absolute round-trip (two-way) jitter in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtMaxAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.21.1.14	PerfCounter64	read-only	Maximum absolute round-trip (two-way) jitter in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtAvgAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.21.1.15	PerfCounter64	read-only	Average absolute round-trip (two-way) jitter in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtNumAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.21.1.16	PerfCounter64	read-only	Number of absolute round-trip (two-way) jitter samples (microseconds).
NUM f3EsaProbeStatsSoamPmExtSumAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.21.1.17	PerfCounter64	read-only	Sum of absolute round-trip (two-way) jitter samples (microseconds).
NUM f3EsaProbeStatsSoamPmExtSumOfSqAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.21.1.18	PerfCounter64	read-only	Sum of squares of absolute round-trip (two-way) jitter samples (microseconds^2).
NUM f3EsaProbeStatsSoamPmExtMaxP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.19	PerfCounter64	read-only	Maximum P2R (Forward) FDR in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtAvgP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.20	PerfCounter64	read-only	Average P2R (Forward) FDR in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtNumP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.21	PerfCounter64	read-only	Number of P2R (Forward) FDR samples (microseconds).
NUM f3EsaProbeStatsSoamPmExtSumP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.22	PerfCounter64	read-only	Sum of P2R (Forward) FDR samples (microseconds).
NUM f3EsaProbeStatsSoamPmExtSumOfSqP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.23	PerfCounter64	read-only	Sum of squares of P2R (Forward) FDR samples (microseconds^2).
NUM f3EsaProbeStatsSoamPmExtMaxR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.24	PerfCounter64	read-only	Maximum R2P (Backward) FDR in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtAvgR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.25	PerfCounter64	read-only	Average R2P (Backward) FDR in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtNumR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.26	PerfCounter64	read-only	Number of R2P (Backward) FDR samples (microseconds).
NUM f3EsaProbeStatsSoamPmExtSumR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.27	PerfCounter64	read-only	Sum of R2P (Backward) FDR samples (microseconds).
NUM f3EsaProbeStatsSoamPmExtSumOfSqR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.28	PerfCounter64	read-only	Sum of squares of R2P (Backward) FDR samples (microseconds^2).
NUM f3EsaProbeStatsSoamPmExtMaxRTFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.29	PerfCounter64	read-only	Maximum round-trip (two-way) FDR in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtAvgRTFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.30	PerfCounter64	read-only	Average round-trip (two-way) FDR in a measurement interval (microseconds).
NUM f3EsaProbeStatsSoamPmExtNumRTFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.31	PerfCounter64	read-only	Number of round-trip (two-way) FDR samples (microseconds).
NUM f3EsaProbeStatsSoamPmExtSumRTFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.32	PerfCounter64	read-only	Sum of round-trip (two-way) FDR samples (microseconds).
NUM f3EsaProbeStatsSoamPmExtSumOfSqRTFDR	1.3.6.1.4.1.2544.1.12.8.1.21.1.33	PerfCounter64	read-only	Sum of squares of round-trip (two-way) FDR samples (microseconds^2).
NUM f3EsaProbeStatsSoamPmExtP2rAvailableDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.21.1.34	PerfCounter64	read-only	Probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeStatsSoamPmExtR2pAvailableDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.21.1.35	PerfCounter64	read-only	Reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeStatsSoamPmExtP2rUnavailableDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.21.1.36	PerfCounter64	read-only	Probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeStatsSoamPmExtR2pUnavailableDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.21.1.37	PerfCounter64	read-only	Reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeStatsSoamPmExtElapsedTime	1.3.6.1.4.1.2544.1.12.8.1.21.1.38	PerfCounter64	read-only	The elapsed time (monotonic time) for the interval which could be less or more than measurement interval based on which the Time of Day was moved forward or backwards respectively (miliseconds).
f3EsaProbeHistorySoamPmExtTable	1.3.6.1.4.1.2544.1.12.8.1.22		not-accessible	A collection of ESA Probe MEF 35 related history kept for a particular ESA Probe entity. These reflect the history data.
f3EsaProbeHistorySoamPmExtEntry	1.3.6.1.4.1.2544.1.12.8.1.22.1		not-accessible	A conceptual row in the f3EsaProbeHistorySoamPmExtTable.
NUM f3EsaProbeHistorySoamPmExtMinP2RFlr	1.3.6.1.4.1.2544.1.12.8.1.22.1.1	PerfCounter64	read-only	This is the minimum probe to reflector FLR.
NUM f3EsaProbeHistorySoamPmExtMaxP2RFlr	1.3.6.1.4.1.2544.1.12.8.1.22.1.2	PerfCounter64	read-only	This is the maximum probe to reflector FLR.
NUM f3EsaProbeHistorySoamPmExtAvgP2RFlr	1.3.6.1.4.1.2544.1.12.8.1.22.1.3	PerfCounter64	read-only	This is the average probe to reflector FLR.
NUM f3EsaProbeHistorySoamPmExtMinR2PFlr	1.3.6.1.4.1.2544.1.12.8.1.22.1.4	PerfCounter64	read-only	This is the minimum reflector to probe FLR.
NUM f3EsaProbeHistorySoamPmExtMaxR2PFlr	1.3.6.1.4.1.2544.1.12.8.1.22.1.5	PerfCounter64	read-only	This is the maximum reflector to probe FLR.
NUM f3EsaProbeHistorySoamPmExtAvgR2PFlr	1.3.6.1.4.1.2544.1.12.8.1.22.1.6	PerfCounter64	read-only	This is the average reflector to probe FLR.
NUM f3EsaProbeHistorySoamPmExtP2rSeverelyErroredDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.22.1.7	PerfCounter64	read-only	This is the number of delta_ts in which the FLR is greater than availability threshold in the probe to reflector direction.
NUM f3EsaProbeHistorySoamPmExtR2PSeverelyErroredDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.22.1.8	PerfCounter64	read-only	This is the number of delta_ts in which the FLR is greater than availability threshold in the reflector to probe direction.
NUM f3EsaProbeHistorySoamPmExtP2rAvailableTime	1.3.6.1.4.1.2544.1.12.8.1.22.1.9	PerfCounter64	read-only	This is the probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeHistorySoamPmExtR2PAvailableTime	1.3.6.1.4.1.2544.1.12.8.1.22.1.10	PerfCounter64	read-only	This is the reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeHistorySoamPmExtP2rUnavailableTime	1.3.6.1.4.1.2544.1.12.8.1.22.1.11	PerfCounter64	read-only	This is the probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeHistorySoamPmExtR2PUnavailableTime	1.3.6.1.4.1.2544.1.12.8.1.22.1.12	PerfCounter64	read-only	This is the reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeHistorySoamPmExtMinAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.22.1.13	PerfCounter64	read-only	Minimum absolute round-trip (two-way) jitter in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtMaxAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.22.1.14	PerfCounter64	read-only	Maximum absolute round-trip (two-way) jitter in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtAvgAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.22.1.15	PerfCounter64	read-only	Average absolute round-trip (two-way) jitter in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtNumAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.22.1.16	PerfCounter64	read-only	Number of absolute round-trip (two-way) jitter samples.
NUM f3EsaProbeHistorySoamPmExtSumAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.22.1.17	PerfCounter64	read-only	Sum of absolute round-trip (two-way) jitter samples.
NUM f3EsaProbeHistorySoamPmExtSumOfSqAbsRTJitter	1.3.6.1.4.1.2544.1.12.8.1.22.1.18	PerfCounter64	read-only	Sum of squares of absolute round-trip (two-way) jitter samples.
NUM f3EsaProbeHistorySoamPmExtMaxP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.19	PerfCounter64	read-only	Maximum P2R (Forward) FDR in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtAvgP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.20	PerfCounter64	read-only	Average P2R (Forward) FDR in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtNumP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.21	PerfCounter64	read-only	Number of P2R (Forward) FDR samples.
NUM f3EsaProbeHistorySoamPmExtSumP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.22	PerfCounter64	read-only	Sum of P2R (Forward) FDR samples.
NUM f3EsaProbeHistorySoamPmExtSumOfSqP2RFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.23	PerfCounter64	read-only	Sum of squares of P2R (Forward) FDR samples.
NUM f3EsaProbeHistorySoamPmExtMaxR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.24	PerfCounter64	read-only	Maximum R2P (Backward) FDR in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtAvgR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.25	PerfCounter64	read-only	Average R2P (Backward) FDR in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtNumR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.26	PerfCounter64	read-only	Number of R2P (Backward) FDR samples.
NUM f3EsaProbeHistorySoamPmExtSumR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.27	PerfCounter64	read-only	Sum of R2P (Backward) FDR samples.
NUM f3EsaProbeHistorySoamPmExtSumOfSqR2PFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.28	PerfCounter64	read-only	Sum of squares of R2P (Backward) FDR samples.
NUM f3EsaProbeHistorySoamPmExtMaxRTFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.29	PerfCounter64	read-only	Maximum round-trip (two-way) FDR in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtAvgRTFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.30	PerfCounter64	read-only	Average round-trip (two-way) FDR in a measurement interval.
NUM f3EsaProbeHistorySoamPmExtNumRTFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.31	PerfCounter64	read-only	Number of round-trip (two-way) FDR samples.
NUM f3EsaProbeHistorySoamPmExtSumRTFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.32	PerfCounter64	read-only	Sum of round-trip (two-way) FDR samples.
NUM f3EsaProbeHistorySoamPmExtSumOfSqRTFDR	1.3.6.1.4.1.2544.1.12.8.1.22.1.33	PerfCounter64	read-only	Sum of squares of round-trip (two-way) FDR samples.
NUM f3EsaProbeHistorySoamPmExtP2rAvailableDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.22.1.34	PerfCounter64	read-only	Probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeHistorySoamPmExtR2pAvailableDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.22.1.35	PerfCounter64	read-only	Reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeHistorySoamPmExtP2rUnavailableDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.22.1.36	PerfCounter64	read-only	Probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeHistorySoamPmExtR2pUnavailableDeltaTs	1.3.6.1.4.1.2544.1.12.8.1.22.1.37	PerfCounter64	read-only	Reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
NUM f3EsaProbeHistorySoamPmExtElapsedTime	1.3.6.1.4.1.2544.1.12.8.1.22.1.38	PerfCounter64	read-only	The elapsed time (monotonic time) for the interval which could be less or more than measurement interval based on which the Time of Day was moved forward or backwards respectively (miliseconds).
cmServAssuranceNotifications	1.3.6.1.4.1.2544.1.12.8.2
NTF cmOperateLoopbackTrap	1.3.6.1.4.1.2544.1.12.8.2.1			This is the Operate Loopback Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1).
NTF cmReleaseLoopbackTrap	1.3.6.1.4.1.2544.1.12.8.2.2			This is the Release Loopback Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1).
NTF esaProbeThresholdCrossingAlert	1.3.6.1.4.1.2544.1.12.8.2.3			This trap is sent each time a threshold on a PM condition on ESA Probe is crossed.
cmServAssuranceConformance	1.3.6.1.4.1.2544.1.12.8.3
cmServAssuranceCompliances	1.3.6.1.4.1.2544.1.12.8.3.1
cmServAssuranceCompliance	1.3.6.1.4.1.2544.1.12.8.3.1.1			Describes the requirements for conformance to the CM ServAssurance group.
cmServAssuranceGroups	1.3.6.1.4.1.2544.1.12.8.3.2
cmServAssuranceObjectGroup	1.3.6.1.4.1.2544.1.12.8.3.2.1			*************** THIS OBJECT GROUP IS NOW DEPRECATED ************* A collection of objects used to manage the CM ServAssurance group.
cmServAssuranceNotifGroup	1.3.6.1.4.1.2544.1.12.8.3.2.2			*************** THIS OBJECT GROUP IS NOW DEPRECATED **************** A collection of notifications used in the CM ServAssurance group.
cmEcpaGroup	1.3.6.1.4.1.2544.1.12.8.3.2.3			A collection of objects used to manage the CM ServAssurance ECPA functionality.
cmEsaGroup	1.3.6.1.4.1.2544.1.12.8.3.2.4			A collection of objects used to manage the CM ServAssurance ESA functionality.
cmServAssuranceGenNotifGroup	1.3.6.1.4.1.2544.1.12.8.3.2.5			A collection of notifications used in the generic CM ServAssurance functionality.
cmServAssuranceEsaNotifGroup	1.3.6.1.4.1.2544.1.12.8.3.2.6			A collection of notifications used in the CM ServAssurance ESA functionality.
cmBertGroup	1.3.6.1.4.1.2544.1.12.8.3.2.7			A collection of objects used to manage the CM ServAssurance BERT functionality.

RFC description

Manages service assurance, probes, reflectors, and performance monitoring on ADVA FSP150 optical networking equipment.

Start monitoring ADVA/Ceragon FSP150 CM/CC (F3) microwave & Carrier Ethernet transport platform with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CM-SA-MIB

What Is CM-SA-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description