CM-SAT-MIB

All MIBs › CM-SAT-MIB

Organization: ADVA Optical Networking SE

Last Updated: 2017-04-05

Category: Vendor: Ceragon

Description: Provides Service Activation Test (SAT) objects for end-to-end diagnostics on Ceragon radio links.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CM-SAT-MIB?

CM-SAT-MIB provides Service Activation Test (SAT) objects, per its module description, for the F3 (FSP150CM/CC) product line associated with ADVA/Ceragon, used for end-to-end diagnostic testing on microwave radio/Carrier Ethernet links. It exposes a control table for configuring and running test instances - test mode, test procedures, committed-information-rate (CIR) test step configuration, and test duration - along with a status object reporting test progress/outcome and an action object to start/stop tests. This is a diagnostics/software-function status MIB rather than a passive hardware-health one: satControlStatus reports whether a service-activation test is running, completed, or failed, which is used to verify that a newly provisioned circuit or radio link meets its committed performance parameters before being placed into production. It is specific to the ADVA/Ceragon F3 (FSP150CM/CC) product architecture and its own cmServActivation object tree rather than a general IETF standard. Typical deployment context is telecom/carrier microwave backhaul or Carrier Ethernet access networks where service activation testing validates SLA compliance on newly turned-up links. Engineers can download the CM-SAT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CM-SAT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ADVA/Ceragon FSP150CM/CC microwave radio or Carrier Ethernet access node

Monitoring Examples

An administrator would configure satControlTable/satControlEntry with satControlTestMode, satControlConfigCIRTestStepNum, and satControlConfigCIRTestStepDuration, then trigger satControlAction to start a CIR step test and poll satControlStatus for pass/fail results. A satControlStatus indicating failure during the configured satControlPerfTestDuration would reveal that the circuit does not meet its committed rate, prompting further link diagnostics. Receiving a trap from cmServActivationNotifications would alert the NMS that a test referenced by satControlIndex/satControlName has completed or encountered an error.

What Can Be Monitored

service activation test status
CIR test step configuration and results
test duration/procedures
test start/stop control

Imported Objects

From ADVA-MIB

fsp150cm

OBJECT-IDENTITY

From CM-COMMON-MIB

AdminState
CmPmBinAction
MepDestinationType
OperationalState
SecondaryState
VlanId
VlanPriority

From CM-ENTITY-MIB

neIndex	OBJECT-TYPE
networkElementEntry	OBJECT-TYPE
shelfIndex	OBJECT-TYPE
slotIndex	OBJECT-TYPE

From CM-FACILITY-MIB

PolicerColorMode

From CM-SA-MIB

EsaProbePktIntervalType

From IEEE8021-CFM-MIB

Dot1agCfmMepIdOrZero
dot1agCfmMepEntry	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
RowStatus
StorageType
TEXTUAL-CONVENTION
TruthValue
VariablePointer

OIDs

OID symbolic	OID numeric	Type	Access	Description
cmServiceActivationMIB	1.3.6.1.4.1.2544.1.12.28			This module defines the Service Activation MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA.
cmServActivationObjects	1.3.6.1.4.1.2544.1.12.28.1
satControlTable	1.3.6.1.4.1.2544.1.12.28.1.1		not-accessible	A list of entries for the control of SAT Control.
satControlEntry	1.3.6.1.4.1.2544.1.12.28.1.1.1		not-accessible	A conceptual row in the satControlTable.
I32 satControlIndex	1.3.6.1.4.1.2544.1.12.28.1.1.1.1	Integer32	not-accessible	The index of the Service Activation Test.
STR satControlName	1.3.6.1.4.1.2544.1.12.28.1.1.1.2	DisplayString	read-write	The alias of the Service Activation Test.
SER satControlTestMode	1.3.6.1.4.1.2544.1.12.28.1.1.1.3	ServiceActivationTestMode	read-write	The mode of the Service Activation Test.
SAT satControlTestProcedures	1.3.6.1.4.1.2544.1.12.28.1.1.1.4	SatProceduresList	read-write	A List of Service Activation Test procedures.
I32 satControlConfigTestDuration	1.3.6.1.4.1.2544.1.12.28.1.1.1.5	Integer32	read-write	The duration of CIR step test, expressed in seconds.
I32 satControlConfigCIRTestStepNum	1.3.6.1.4.1.2544.1.12.28.1.1.1.6	Integer32	read-write	The number of steps in CIR step test.
I32 satControlConfigCIRTestStepDuration	1.3.6.1.4.1.2544.1.12.28.1.1.1.7	Integer32	read-write	The duration of each CIR step test.
I32 satControlPerfTestDuration	1.3.6.1.4.1.2544.1.12.28.1.1.1.8	Integer32	read-write	The duration of the SAT Performance Test, expressed in minutes.
SAT satControlStatus	1.3.6.1.4.1.2544.1.12.28.1.1.1.9	SatStatus	read-only	The overall SAT Control Test Status.
SAT satControlAction	1.3.6.1.4.1.2544.1.12.28.1.1.1.10	SatTestAction	read-write	The start/stop action of the SAT Control.
STO satControlStorageType	1.3.6.1.4.1.2544.1.12.28.1.1.1.11	StorageType	read-create	The type of storage configured for this entry.
ROW satControlRowStatus	1.3.6.1.4.1.2544.1.12.28.1.1.1.12	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of satControlRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with satControlRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The satControlRowStatus object may be modified if the associated instance of this object is equal to active(1).
STR satControlFailCause	1.3.6.1.4.1.2544.1.12.28.1.1.1.13	DisplayString	read-only	The information about the reason of the Test failure.
DAT satControlTestStartTime	1.3.6.1.4.1.2544.1.12.28.1.1.1.14	DateAndTime	read-only	The start time of this SAT Control.
T/F satControlFlpduTagOverride	1.3.6.1.4.1.2544.1.12.28.1.1.1.15	TruthValue	read-write	Whether permit user to configure FLPDU explicitly. Disabled: FLPDUs tag is inherited from SCM of MEP. Enabled: User can configure FLPDUs tag explicitly, which will override the VLAN tags from MEP.
satStreamTable	1.3.6.1.4.1.2544.1.12.28.1.2		not-accessible	A list of entries for the control of SAT Streams.
satStreamEntry	1.3.6.1.4.1.2544.1.12.28.1.2.1		not-accessible	A conceptual row in the satStreamTable.
I32 satStreamIndex	1.3.6.1.4.1.2544.1.12.28.1.2.1.1	Integer32	not-accessible	The index of the Service Activation Test Stream.
STR satStreamName	1.3.6.1.4.1.2544.1.12.28.1.2.1.2	DisplayString	read-write	The alias of the Service Activation Test Stream.
NUM satStreamTestPort	1.3.6.1.4.1.2544.1.12.28.1.2.1.3	VariablePointer	read-write	The related port of the Service Activation Test Stream.
SAT satStreamTestDirection	1.3.6.1.4.1.2544.1.12.28.1.2.1.4	SatDirection	read-write	The direction of the Service Activation Test Stream.
MAC satStreamDestMacAddress	1.3.6.1.4.1.2544.1.12.28.1.2.1.5	MacAddress	read-write	This object describes the destination MAC address of FLPDU.
SAT satStreamFramePayloadType	1.3.6.1.4.1.2544.1.12.28.1.2.1.6	SatFramePayloadType	read-write	The type of Payload of the Frame Loss PDU.
STR satStreamCustomFramePayload	1.3.6.1.4.1.2544.1.12.28.1.2.1.7	DisplayString	read-write	This object describes the customized frame payload.
STR satStreamFrameSizeList	1.3.6.1.4.1.2544.1.12.28.1.2.1.8	DisplayString	read-write	This object describes a list of Frame Sizes used in FLPDU.
NUM satStreamSacProfileId	1.3.6.1.4.1.2544.1.12.28.1.2.1.9	VariablePointer	read-write	This object describes the related Service Acceptance Criteria (SAC) Profile Id.
NUM satStreamSrcMepId	1.3.6.1.4.1.2544.1.12.28.1.2.1.10	VariablePointer	read-write	This object describes the Local MEP related with SAT Test Stream.
MEP satStreamDestMepType	1.3.6.1.4.1.2544.1.12.28.1.2.1.11	MepDestinationType	read-write	This object describes the type of Destination MEP, which can be based on MEP id or MAC Address. This is applicable only if satStreamDestMepEnabled is true.
I32 satStreamDestMepId	1.3.6.1.4.1.2544.1.12.28.1.2.1.12	Integer32	read-write	This object describes the destination MEP id. This is applicable only if satStreamDestMepEnabled is true.
MAC satStreamDestMepMacAddr	1.3.6.1.4.1.2544.1.12.28.1.2.1.13	MacAddress	read-write	This object describes the Destination MEP's MAC Address. This is applicable only if satStreamDestMepEnabled is true.
I32 satStreamDmmPacketSize	1.3.6.1.4.1.2544.1.12.28.1.2.1.14	Integer32	read-write	This object describes the Delay Measurement Message (DMM) frame size.
NUM satStreamDmmPacketInterval	1.3.6.1.4.1.2544.1.12.28.1.2.1.15	EsaProbePktIntervalType	read-write	This object describes the Delay Measurement Message (DMM) frame generation interval.
SAT satStreamOverallResult	1.3.6.1.4.1.2544.1.12.28.1.2.1.16	SatResult	read-only	This object describes the test result.
SAT satStreamAction	1.3.6.1.4.1.2544.1.12.28.1.2.1.17	SatTestAction	read-write	This object describes the operation on this test.
SAT satStreamStatus	1.3.6.1.4.1.2544.1.12.28.1.2.1.18	SatStatus	read-only	This object describes the test status of this Test Stream.
SAT satStreamCurrentTestProcedure	1.3.6.1.4.1.2544.1.12.28.1.2.1.19	SatProceduresType	read-only	This object describes the current test procedure.
I32 satStreamCurrentConfigCirTestStep	1.3.6.1.4.1.2544.1.12.28.1.2.1.20	Integer32	read-only	This object describes the current step number of CIR Test.
VLA satStreamInner1VlanId	1.3.6.1.4.1.2544.1.12.28.1.2.1.21	VlanId	read-write	This object describes the Inner1 VLAN Id.
VLA satStreamInner1VlanPri	1.3.6.1.4.1.2544.1.12.28.1.2.1.22	VlanPriority	read-write	This object describes the Inner1 VLAN Priority.
T/F satStreamInner1VlanEnabled	1.3.6.1.4.1.2544.1.12.28.1.2.1.23	TruthValue	read-write	This object describes whether the Inner1 VLAN enabled.
I32 satStreamInner1ValnEtherType	1.3.6.1.4.1.2544.1.12.28.1.2.1.24	Integer32	read-write	This object describes the Inner2 VLAN EtherType.
VLA satStreamInner2VlanId	1.3.6.1.4.1.2544.1.12.28.1.2.1.25	VlanId	read-write	This object describes the Inner2 VLAN Id.
VLA satStreamInner2VlanPri	1.3.6.1.4.1.2544.1.12.28.1.2.1.26	VlanPriority	read-write	This object describes the Inner2 VLAN Priority.
T/F satStreamInner2VlanEnabled	1.3.6.1.4.1.2544.1.12.28.1.2.1.27	TruthValue	read-write	This object describes whether the Inner2 VLAN enabled.
I32 satStreamInner2VlanEtherType	1.3.6.1.4.1.2544.1.12.28.1.2.1.28	Integer32	read-write	This object describes whether the Inner2 VLAN ether type.
VLA satStreamOuterVlanId	1.3.6.1.4.1.2544.1.12.28.1.2.1.29	VlanId	read-write	This object describes the Outer VLAN Id.
VLA satStreamOuterVlanPri	1.3.6.1.4.1.2544.1.12.28.1.2.1.30	VlanPriority	read-write	This object describes the Outer VLAN Priority.
T/F satStreamOuterVlanEnabled	1.3.6.1.4.1.2544.1.12.28.1.2.1.31	TruthValue	read-write	This object describes whether the Outer VLAN enabled.
I32 satStreamOuterVlanEtherType	1.3.6.1.4.1.2544.1.12.28.1.2.1.32	Integer32	read-write	This object describes whether the Outer VLAN Ethertype.
T/F satStreamDeiEnabled	1.3.6.1.4.1.2544.1.12.28.1.2.1.33	TruthValue	read-write	This object describes whether the DEI enabled.
I32 satStreamGreenPcp	1.3.6.1.4.1.2544.1.12.28.1.2.1.34	Integer32	read-write	This object describes the PCP value for Green Packets.
I32 satStreamYellowPcp	1.3.6.1.4.1.2544.1.12.28.1.2.1.35	Integer32	read-write	This object describes the PCP value for Yellow Packets.
POL satStreamColorMode	1.3.6.1.4.1.2544.1.12.28.1.2.1.36	PolicerColorMode	read-write	This object describes the color mode for Policing test.
U32 satStreamCirLo	1.3.6.1.4.1.2544.1.12.28.1.2.1.37	Unsigned32	read-write	This object describes CIR low 32 bits.
U32 satStreamCirHi	1.3.6.1.4.1.2544.1.12.28.1.2.1.38	Unsigned32	read-write	This object describes CIR high 32 bits.
U32 satStreamEirLo	1.3.6.1.4.1.2544.1.12.28.1.2.1.39	Unsigned32	read-write	This object describes EIR low 32 bits.
U32 satStreamEirHi	1.3.6.1.4.1.2544.1.12.28.1.2.1.40	Unsigned32	read-write	This object describes EIR high 32 bits.
U32 satStreamCbs	1.3.6.1.4.1.2544.1.12.28.1.2.1.41	Unsigned32	read-write	This object describes CBS.
U32 satStreamEbs	1.3.6.1.4.1.2544.1.12.28.1.2.1.42	Unsigned32	read-write	This object describes CBS.
STO satStreamStorageType	1.3.6.1.4.1.2544.1.12.28.1.2.1.43	StorageType	read-create	The type of storage configured for this entry.
ROW satStreamRowStatus	1.3.6.1.4.1.2544.1.12.28.1.2.1.44	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of satStreamRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with satStreamRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The satStreamRowStatus object may be modified if the associated instance of this object is equal to active(1).
VLA satStreamDmmPktPriority	1.3.6.1.4.1.2544.1.12.28.1.2.1.45	VlanPriority	read-write	This object describes the Dmm packet priority.
U32 satStreamMFactor	1.3.6.1.4.1.2544.1.12.28.1.2.1.46	Unsigned32	read-write	The M factor is used in test result validation. It is added to allow for the effect of the traffic policer's CBS and EBS settings and test time. Roughly, it equals to EBS/Test Duration, user should configure its value based on experience test.
T/F satStreamDestMepEnabled	1.3.6.1.4.1.2544.1.12.28.1.2.1.47	TruthValue	read-write	For a SAT two-way test, the remote end is expected to have a loopback for FLPDUs, but it may or may not have a Responder MEP to process DMMs. This object indicates whether the remote end has a Responder MEP or not. If the Responder MEP is present, two-way delay is computed by the Controller MEP once DMR is received, if the Responder MEP is not present, the two-way delay is computed when the Controller MEP receives the looped back DMM.
T/F satStreamLlActivateEnabled	1.3.6.1.4.1.2544.1.12.28.1.2.1.48	TruthValue	read-write	This attribute specifies whether Latching Loopback needs to be activated for the SAT stream during a SAT test. It is only applicable for two way test.
satResultStatsTable	1.3.6.1.4.1.2544.1.12.28.1.3		not-accessible	A list of entries for the control of SAT Result Statistics.
satResultStatsEntry	1.3.6.1.4.1.2544.1.12.28.1.3.1		not-accessible	A conceptual row in the satResultStatsTable.
SAT satResultStatsTestType	1.3.6.1.4.1.2544.1.12.28.1.3.1.1	SatProceduresType	not-accessible	The Test Type of the Service Activation Test.
I32 satResultStatsStepNumber	1.3.6.1.4.1.2544.1.12.28.1.3.1.2	Integer32	not-accessible	The Test step number of the Service Activation Test.
U32 satResultStatsSessionId	1.3.6.1.4.1.2544.1.12.28.1.3.1.3	Unsigned32	read-only	The session id of the Service Activation Test.
DAT satResultStatsStartTime	1.3.6.1.4.1.2544.1.12.28.1.3.1.4	DateAndTime	read-only	The start time of the Service Activation Test.
DAT satResultStatsEndTime	1.3.6.1.4.1.2544.1.12.28.1.3.1.5	DateAndTime	read-only	The end time of the Service Activation Test.
SAT satResultStatsStatus	1.3.6.1.4.1.2544.1.12.28.1.3.1.6	SatStatus	read-only	The Status of the Service Activation Test.
SAT satResultStatsResult	1.3.6.1.4.1.2544.1.12.28.1.3.1.7	SatResult	read-only	This object describes SAT whether pass.
C64 satResultStatsMinIRGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.8	Counter64	read-only	This object describes the minimum Information Rate (IR) for Green Packets.
C64 satResultStatsAvgIRGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.9	Counter64	read-only	This object describes the average Information Rate (IR) for Green Packets.
C64 satResultStatsMaxIRGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.10	Counter64	read-only	This object describes the maximum Information Rate (IR) for Green Packets.
C64 satResultStatsMinIRYMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.11	Counter64	read-only	This object describes the minimum Information Rate (IR) for Yellow Packets.
C64 satResultStatsAvgIRYMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.12	Counter64	read-only	This object describes the average Information Rate (IR) for Yellow Packets.
C64 satResultStatsMaxIRYMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.13	Counter64	read-only	This object describes the maximum Information Rate (IR) for Yellow Packets.
I32 satResultStatsFlrGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.14	Integer32	read-only	This object describes the Frame Loss Ratio (FLR) for Green Packets. From the EGX8.2 and GE110 7.1, If its value is 26000001, it means 26.000001% frame lost. For the earlier release, If its value is 260001, it means 26.0001% frame lost.
I32 satResultStatsFlrYMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.15	Integer32	read-only	This object describes the Frame Loss Ratio (FLR) for Yellow Packets. From the EGX8.2 and GE110 7.1, If its value is 26000001, it means 26.000001% frame lost. For the earlier release, If its value is 260001, it means 26.0001% frame lost.
C64 satResultStatsFlrGCounts	1.3.6.1.4.1.2544.1.12.28.1.3.1.16	Counter64	read-only	This object describes the Frame Loss (FL) count for Green Packets.
C64 satResultStatsFlrYCounts	1.3.6.1.4.1.2544.1.12.28.1.3.1.17	Counter64	read-only	This object describes the Frame Loss (FL) count for Yellow Packets.
U32 satResultStatsMinFTDGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.18	Unsigned32	read-only	This object describes the minimum Frame Transfer Delay (FTD) for Green Packets.
U32 satResultStatsAvgFTDGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.19	Unsigned32	read-only	This object describes the average Frame Transfer Delay (FTD) for Green Packets.
U32 satResultStatsMaxFTDGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.20	Unsigned32	read-only	This object describes the maximum Frame Transfer Delay (FTD) for Green Packets.
U32 satResultStatsIMinFDVGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.21	Unsigned32	read-only	This object describes the minimum Frame Delay Variation (FDV) for Green Packets.
U32 satResultStatsIAvgFDVGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.22	Unsigned32	read-only	This object describes the average Frame Delay Variation (FDV) for Green Packets.
U32 satResultStatsIMaxFDVGMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.23	Unsigned32	read-only	This object describes the maximum Frame Delay Variation (FDV) for Green Packets.
U32 satResultStatsISyncErrorsNum	1.3.6.1.4.1.2544.1.12.28.1.3.1.24	Unsigned32	read-only	The number of (time) Synchronization Errors between SAT Control and SAT Responder in the current Test.
T/F satResultStatsIfNegFLG	1.3.6.1.4.1.2544.1.12.28.1.3.1.25	TruthValue	read-only	This object means whether negative green frame loss. True: negative loss of green packets occurs, which means receiving more green packets than expected. False: negative loss of green packets doesn't occur, which means not receiving more green packets than expected.
T/F satResultStatsIfNegFLY	1.3.6.1.4.1.2544.1.12.28.1.3.1.26	TruthValue	read-only	This object means whether negative yellow frame loss. True: negative loss of yellow packets occurs, which means receiving more yellow packets than expected. False: negative loss of yellow packets doesn't occur, which means not receiving more yellow packets than expected.
C64 satResultStatsAvgIRT	1.3.6.1.4.1.2544.1.12.28.1.3.1.27	Counter64	read-only	This object describes Average IR of total packets, non distinguishing green or yellow. Only valid for color blind test.
I32 satResultStatsFlrTMeasured	1.3.6.1.4.1.2544.1.12.28.1.3.1.28	Integer32	read-only	This object describes the Frame Loss Ratio (FLR) for Total Packets. No distinguish color, negative value means receiving much more packets than expected. Only valid for color blind test. If its value is 26000001, it means 26.000001% frame lost.
C64 satResultStatsFlTCounts	1.3.6.1.4.1.2544.1.12.28.1.3.1.29	Counter64	read-only	This object describes the Frame Loss (FL) count for Total Packets.
T/F satResultStatsIfNegFLT	1.3.6.1.4.1.2544.1.12.28.1.3.1.30	TruthValue	read-only	This object means whether negative total frame loss. True: negative loss of green packets occurs, which means receiving more green packets than expected. False: negative loss of green packets doesn't occur, which means not receiving more green packets than expected.
satSacProfileTable	1.3.6.1.4.1.2544.1.12.28.1.4		not-accessible	A list of entries for the control of SAT Service Acceptance Criteria (SAC) Profile.
satSacProfileEntry	1.3.6.1.4.1.2544.1.12.28.1.4.1		not-accessible	A conceptual row in the satSacProfileTable.
I32 satSacProfileIndex	1.3.6.1.4.1.2544.1.12.28.1.4.1.1	Integer32	not-accessible	The index of SAT Service Acceptance Criteria (SAC) Profile.
STR satSacProfileAlias	1.3.6.1.4.1.2544.1.12.28.1.4.1.2	DisplayString	read-write	The alias of SAT Service Acceptance Criteria (SAC) Profile.
I32 satSacProfileFLR	1.3.6.1.4.1.2544.1.12.28.1.4.1.3	Integer32	read-write	The Frame Loss Ratio (FLR) acceptance criteria of this SAC Profile. From the EGX8.2 and GE110 7.1, If its value is 26000001, it means 26.000001% frame lost. For the earlier release, If its value is 260001, it means 26.0001% frame lost.
U32 satSacProfileFTD	1.3.6.1.4.1.2544.1.12.28.1.4.1.4	Unsigned32	read-write	The Frame Transfer Delay (FTD) acceptance criteria of this SAC Profile.
U32 satSacProfileFDV	1.3.6.1.4.1.2544.1.12.28.1.4.1.5	Unsigned32	read-write	The frame transfer delay variation of SAT Service Acceptance Criteria (SAC) Profile.
STO satSacProfileStorageType	1.3.6.1.4.1.2544.1.12.28.1.4.1.6	StorageType	read-create	The type of storage configured for this entry.
ROW satSacProfileRowStatus	1.3.6.1.4.1.2544.1.12.28.1.4.1.7	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of satSacProfileRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with satSacProfileRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The satSacProfileRowStatus object may be modified if the associated instance of this object is equal to active(1).
satResponderSessionTable	1.3.6.1.4.1.2544.1.12.28.1.5		not-accessible	A list of entries for the control of SAT Responder Session.
satResponderSessionEntry	1.3.6.1.4.1.2544.1.12.28.1.5.1		not-accessible	A conceptual row in the satResponderSessionTable.
U32 satResponderSessionIndex	1.3.6.1.4.1.2544.1.12.28.1.5.1.1	Unsigned32	not-accessible	The index of the entry.
U32 satResponderSessionId	1.3.6.1.4.1.2544.1.12.28.1.5.1.2	Unsigned32	read-only	The id of active test session negotiated between SAT Responder and SAT Control.
MAC satResponderSessionControlMepMacAddr	1.3.6.1.4.1.2544.1.12.28.1.5.1.3	MacAddress	read-only	This object describes the Control MEP's MAC Address.
NUM satResponderSessionMepId	1.3.6.1.4.1.2544.1.12.28.1.5.1.4	VariablePointer	read-only	The local MEP Id.
STO satResponderSessionStorageType	1.3.6.1.4.1.2544.1.12.28.1.5.1.5	StorageType	read-create	The type of storage configured for this entry.
ROW satResponderSessionRowStatus	1.3.6.1.4.1.2544.1.12.28.1.5.1.6	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of satResponderSessionRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with satResponderSessionRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The satResponderSessionRowStatus object may be modified if the associated instance of this object is equal to active(1).
networkElementSatParamsTable	1.3.6.1.4.1.2544.1.12.28.1.6		not-accessible	Entries may be auto discovered, or can be explicitly created by SNMP Manager. Each remotely discovered shelf is represented as a row in this table.
networkElementSatParamsEntry	1.3.6.1.4.1.2544.1.12.28.1.6.1		not-accessible	A conceptual row in the networkElementSatParamsTable.
U32 neSatParamsEtherType	1.3.6.1.4.1.2544.1.12.28.1.6.1.1	Unsigned32	read-write	This object describes the SAT System EtherType.
satCfmMepExtTable	1.3.6.1.4.1.2544.1.12.28.1.7		not-accessible	This objects describe the SAT responder whether enabled on the MEP.
satCfmMepExtEntry	1.3.6.1.4.1.2544.1.12.28.1.7.1		not-accessible	A conceptual row in the satCfmMepExtTable.
T/F satCfmMepSatResponderEnabled	1.3.6.1.4.1.2544.1.12.28.1.7.1.1	TruthValue	read-write	This objects describes the SAT Responder whether enabled on the MEP.
cmServActivationNotifications	1.3.6.1.4.1.2544.1.12.28.2
cmServActivationConformance	1.3.6.1.4.1.2544.1.12.28.3
cmServActivationCompliances	1.3.6.1.4.1.2544.1.12.28.3.1
cmServActivationCompliance	1.3.6.1.4.1.2544.1.12.28.3.1.1			Describes the requirements for conformance to the CM SAT group.
cmServActivationGroups	1.3.6.1.4.1.2544.1.12.28.3.2
cmSatGroup	1.3.6.1.4.1.2544.1.12.28.3.2.1			A collection of objects used to manage the CM SAT functionality.

RFC description

Vendor MIB for cable modem and satellite system management (vendor-private).

Start monitoring ADVA/Ceragon FSP150 CM/CC (F3) microwave & Carrier Ethernet transport platform with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CM-SAT-MIB

What Is CM-SAT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description