ADN-ENV-MIB

All MIBs › ADN-ENV-MIB

Category: Environmental Monitoring

Description: Monitors environmental conditions such as temperature and humidity for ADN network equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ADN-ENV-MIB?

ADN-ENV-MIB is a vendor-private MIB whose own module description flags it as internal, used by FRANP (Frame Relay Network Access Point) signalling for debugging purposes rather than for routine operational monitoring. Its data is a channel-level signalling table tracking resource availability, bandwidth threshold, a call-control-block (CCB) reference, and diagnostic trace controls per Frame Relay channel. Because the module itself frames this as a debug aid, it is mainly of interest when working with the vendor's support team to diagnose a Frame Relay signalling problem rather than for everyday capacity monitoring. It is deployed on Frame Relay access equipment implementing FRANP-based signalling. Engineers can download the ADN-ENV-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ADN-ENV-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Frame Relay access equipment implementing FRANP-based signalling

Monitoring Examples

A vendor support engineer enables adnFrtChanSiTraceCntl on a specific channel to capture FRANP signalling trace data while reproducing a reported Frame Relay call-setup problem.

What Can Be Monitored

per-channel resource availability and bandwidth threshold
signalling trace control

Imported Objects

From ADN-MIB

AdnCouplerIndex
AdnEnableDisabled
AdnFrtVCStates
AdnPercent
adn	OBJECT-IDENTITY
adnAtmUniVcCconnectIndex	OBJECT-TYPE
adnAtmUniVpCconnectIndex	OBJECT-TYPE
adnCongMgmtVCDLCIIndex	OBJECT-TYPE
adnEnvHss	OBJECT-IDENTITY
adnEquipIndex	OBJECT-TYPE
adnEquipType	OBJECT-TYPE
adnFrtVCDLCIIndex	OBJECT-TYPE
adnLapDLCIIndex	OBJECT-TYPE

From ATM-MIB

atmVclVci	OBJECT-TYPE
atmVclVpi	OBJECT-TYPE
atmVplVpi	OBJECT-TYPE

From FRNETSERV-MIB

frPVCEndptDLCIIndex

OBJECT-TYPE

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
adnFranpTrunkEnvMIB	1.3.6.1.4.1.637.3.1.8.5.1
adnFrtChanSiTable	1.3.6.1.4.1.637.3.1.8.5.1.1		not-accessible	This table is internal for use by FRANP Signalling for the purpose of debugging.
adnFrtChanSiEntry	1.3.6.1.4.1.637.3.1.8.5.1.1.1		not-accessible	An entry in the Signalling Trunk Channel Table. There will be one entry for each FRANP Signalling Trunk channel configured. This table will also be indexed by adnFrtChanSiIndex in order to be able to access individual trace entries.
INT adnFrtChanSiIndex	1.3.6.1.4.1.637.3.1.8.5.1.1.1.1	INTEGER	read-only	This entry represents the current instance or index of the table. It is provided in order to be able to dump each instance of each object.
INT adnFrtChanSiResourceAvail	1.3.6.1.4.1.637.3.1.8.5.1.1.1.2	INTEGER	read-write	This timer specifies the amount of time to wait for a resource available message to be sent to FRANP Path Select SwBB. If the timer expires, then the message is transmitted. This is expressed in SECONDS. The timer may be set by SNMP command.
ADN adnFrtChanSiBWThreshold	1.3.6.1.4.1.637.3.1.8.5.1.1.1.3	AdnPercent	read-write	The threshold value is specified as a percentage of the BAT. If the available bandwidth drops below this threshold, the resource available message sent to FRANP Path Select component. The value may be set by SNMP command.
OCT adnFrtChanSiCcb	1.3.6.1.4.1.637.3.1.8.5.1.1.1.4	OCTET STRING	read-only	This is the internal BINARY trace area for call control information trace area, maintained by FRANP_SI. It is placed here for maintenance purposes only.
INT adnFrtChanSiTraceCntl	1.3.6.1.4.1.637.3.1.8.5.1.1.1.5	INTEGER	read-write	This object provides a mechanism for controlling Franp Signalling ability to enable/disable tracing data from its Bus side, Trunk side, and Ism side. The following are the possible values it can hold. 1 - Trace activity enabled (normally is defaulted on) 2 - Trace activity disabled
INT adnFrtChanSiTraceSize	1.3.6.1.4.1.637.3.1.8.5.1.1.1.6	INTEGER	read-write	This object provides a mechanism for defining the number of entries the Franp Signalling trace area can have. Be aware when issuing a set command to modify this value, any existing trace data will be lost to make room for the new trace block size.
OCT adnFrtChanSiTraceArea	1.3.6.1.4.1.637.3.1.8.5.1.1.1.7	OCTET STRING	read-only	This is the internal BINARY message trace entry maintained by FRANP_SI for its 3 main interfaces, (Bus side, Trunk side, and Ism side). This entry is instantiated by AdnFrtChanSiInstance index that comprises the entire trace area table. The FRANP Signalling software is implemented as a Finite State Machine, and all message events received are stored here. It is placed here for maintenance purposes only.
OCT adnFrtChanSiBsiStat	1.3.6.1.4.1.637.3.1.8.5.1.1.1.8	OCTET STRING	read-only	This is the internal BINARY statistic trace table maintained by FRANP_SI for this Bus Side interface. The Franp Signalling software is implemented as a Finite State Machine, and all statistics collected are stored here. It is placed here for maintenance purposes only.
OCT adnFrtChanSiTsiStat	1.3.6.1.4.1.637.3.1.8.5.1.1.1.9	OCTET STRING	read-only	This is the internal BINARY statistic trace table maintained by FRANP_SI for this Trunk Side interface. The Franp Signalling software is implemented as a Finite State Machine, and all statistics collected are stored here. It is placed here for maintenance purposes only.
OCT adnFrtChanSiBsiCrfa	1.3.6.1.4.1.637.3.1.8.5.1.1.1.10	OCTET STRING	read-only	This is the internal BINARY call reference active trace maintained by FRANP_SI for this Bus Side interface. It is placed here for maintenance purposes only.
OCT adnFrtChanSiTsiCrfa	1.3.6.1.4.1.637.3.1.8.5.1.1.1.11	OCTET STRING	read-only	This is the internal BINARY call reference active trace maintained by FRANP_SI for this Trunk Side interface. It is placed here for maintenance purposes only.
OCT adnFrtChanSiTsiBwi	1.3.6.1.4.1.637.3.1.8.5.1.1.1.12	OCTET STRING	read-only	This is the internal BINARY Bandwidth Information table maintained by FRANP_SI for this Trunk Side interface. It is placed here for maintenance purposes only.
ADN adnFrtChanSiMinDlyPct	1.3.6.1.4.1.637.3.1.8.5.1.1.1.13	AdnPercent	read-write	This field is used to calculate the minimum delay change a periodic delay measurement can consider to be significant. Such significant delay changes may result in a new delay reported to ROUTES. The minimum delay change is calulated by multiplying this field as a percentage times the delay measured immediately after a RESTART/RESTART ACK exchange.
INT adnFrtChanSiMinDlyAmt	1.3.6.1.4.1.637.3.1.8.5.1.1.1.14	INTEGER	read-write	If the minimum delay change calculated using adnFrtChanSiMinDlyPct is less than this field, the minimum delay change a periodic delay measurement can consider to be significant is set equal to this field instead of the calculated value.
INT adnFrtChanSiDlyPersis	1.3.6.1.4.1.637.3.1.8.5.1.1.1.15	INTEGER	read-write	Before a periodic delay measurement can report a new delay value to ROUTES, a specified number of consecutive measurements must be significantly high OR a specified number of consecutive measurements must be significantly low. This field defines that specified number of consecutive measurements.
adnFrtChanSwTable	1.3.6.1.4.1.637.3.1.8.5.1.2		not-accessible	This table contains internal channel level information for FRANP_SW. There is no existing standard MIB for Alcatel internal network protocol.
adnFrtChanSwEntry	1.3.6.1.4.1.637.3.1.8.5.1.2.1		not-accessible	An entry in the internal FRANP Switching Channel Table. There will be one entry for each FRANP channel configured
OCT adnFrtChanSwFRSI	1.3.6.1.4.1.637.3.1.8.5.1.2.1.3	OCTET STRING	read-only	This is the BINARY internal channel structure maintained by FRSI portion of FRANP_SW for this channel. It is placed here for maintenance purposes only.
OCT adnFrtChanSwIWF	1.3.6.1.4.1.637.3.1.8.5.1.2.1.4	OCTET STRING	read-only	This is the BINARY internal channel structure maintained by TPX/F IWF portion of FRANP_SW for this channel. It is placed here for maintenance purposes only.
OCT adnFrtChanSwFRSIMsgtrace	1.3.6.1.4.1.637.3.1.8.5.1.2.1.5	OCTET STRING	read-only	This is the internal BINARY message trace table maintained by FRSI portion of FRANP_SW for this channel. It is placed here for maintenance purposes only.
adnFrtVCSiTable	1.3.6.1.4.1.637.3.1.8.5.1.3		not-accessible	This is the PVC table for FRANP trunk protocol.
adnFrtVCSiEntry	1.3.6.1.4.1.637.3.1.8.5.1.3.1		not-accessible	PVC table entry
INT adnFrtVCSiBsiCrf	1.3.6.1.4.1.637.3.1.8.5.1.3.1.1	INTEGER	read-only	This is the Bus Side Interface call reference associated with the VC.
ADN adnFrtVCSiBsiState	1.3.6.1.4.1.637.3.1.8.5.1.3.1.2	AdnFrtVCStates	read-write	Define here are the state that are implemented and supported for the FRANP Signalling bus Side Interface.
INT adnFrtVCSiTsiCrf	1.3.6.1.4.1.637.3.1.8.5.1.3.1.3	INTEGER	read-only	This is the Trunk Side Interface call reference associated with the VC.
ADN adnFrtVCSiTsiState	1.3.6.1.4.1.637.3.1.8.5.1.3.1.4	AdnFrtVCStates	read-write	Define here are the state that are implemented and supported for the FRANP Signalling Trunk Side Interface.
INT adnFrtVCSiLocalSuid	1.3.6.1.4.1.637.3.1.8.5.1.3.1.5	INTEGER	read-only	This is the local Suid associated with the VC.
INT adnFrtVCSiLocalLpx	1.3.6.1.4.1.637.3.1.8.5.1.3.1.6	INTEGER	read-only	This is the local LPX associated with the VC.
INT adnFrtVCSiLocalMcmp	1.3.6.1.4.1.637.3.1.8.5.1.3.1.7	INTEGER	read-only	This is the local Maximum Congestion Monitoring Period associated with the VC.
INT adnFrtVCSiLocalAppl	1.3.6.1.4.1.637.3.1.8.5.1.3.1.8	INTEGER	read-only	This is the local Application reference number associated with the VC.
INT adnFrtVCSiLocalData	1.3.6.1.4.1.637.3.1.8.5.1.3.1.9	INTEGER	read-only	This is the local Data Handler reference number associated with the VC.
INT adnFrtVCSiLocalFranpSi	1.3.6.1.4.1.637.3.1.8.5.1.3.1.10	INTEGER	read-only	This is the local Franp Signalling reference number associated with the VC.
NUM adnFrtVCSiLocalifIndex	1.3.6.1.4.1.637.3.1.8.5.1.3.1.11	InterfaceIndex	read-only	This indicates the ifindex of the remote Chassis/Slot/ Port/Channel.
INT adnFrtVCSiRemoteSuid	1.3.6.1.4.1.637.3.1.8.5.1.3.1.12	INTEGER	read-only	This is the remote Suid associated with the VC.
INT adnFrtVCSiRemoteLpx	1.3.6.1.4.1.637.3.1.8.5.1.3.1.13	INTEGER	read-only	This is the remote Lpx associated with the VC.
INT adnFrtVCSiRemoteMcmp	1.3.6.1.4.1.637.3.1.8.5.1.3.1.14	INTEGER	read-only	This is the remote Maximum Congestion Monitoring period associated with the VC.
INT adnFrtVCSiRemoteAppl	1.3.6.1.4.1.637.3.1.8.5.1.3.1.15	INTEGER	read-only	This is the remote Application reference number associated with the VC.
INT adnFrtVCSiRemoteData	1.3.6.1.4.1.637.3.1.8.5.1.3.1.16	INTEGER	read-only	This is the remote Data Handler reference number associated with the VC.
INT adnFrtVCSiRemoteFranpSi	1.3.6.1.4.1.637.3.1.8.5.1.3.1.17	INTEGER	read-only	This is the remote Franp Signalling reference number associated with the VC.
NUM adnFrtVCSiRemoteifIndex	1.3.6.1.4.1.637.3.1.8.5.1.3.1.18	InterfaceIndex	read-only	This indicates the ifindex of the remote Chassis/Slot/ Port/Channel.
INT adnFrtVCSiBsiTimer	1.3.6.1.4.1.637.3.1.8.5.1.3.1.19	INTEGER	read-only	This is the timer ID that is currently running for this VC.
INT adnFrtVCSiTsiTimer	1.3.6.1.4.1.637.3.1.8.5.1.3.1.20	INTEGER	read-only	This is the timer ID that is currently running for this VC.
CTR adnFrtVCSiBsiTimerExpCnt	1.3.6.1.4.1.637.3.1.8.5.1.3.1.21	Counter	read-only	This is the number of times this Bus Side Interface timer ID has expired.
CTR adnFrtVCSiTsiTimerExpCnt	1.3.6.1.4.1.637.3.1.8.5.1.3.1.22	Counter	read-only	This is the number of times this trunk Side Interface timer ID has expired.
adnFrtVCSwTable	1.3.6.1.4.1.637.3.1.8.5.1.4		not-accessible	This is the internal VC table for FRANP Switching.
adnFrtVCSwEntry	1.3.6.1.4.1.637.3.1.8.5.1.4.1		not-accessible	PVC table entry
OCT adnFrtVCSwFRSI	1.3.6.1.4.1.637.3.1.8.5.1.4.1.1	OCTET STRING	read-only	This is the BINARY internal VC structure maintained by the FRSI portion of FRANP_SW. It is placed here for maintenance purposes only.
OCT adnFrtVCSwIWF	1.3.6.1.4.1.637.3.1.8.5.1.4.1.2	OCTET STRING	read-only	This is the BINARY internal VC structure maintained by the TPX/F IWF portion of FRANP_SW. It is placed here for maintenance purposes only.
OCT adnFrtVCSwFRSIMsgtrace	1.3.6.1.4.1.637.3.1.8.5.1.4.1.3	OCTET STRING	read-only	This is the internal BINARY message trace table maintained by the FRSI portion of FRANP_SW for this VC. It is placed here for maintenance purposes only.
adnFrtSiTable	1.3.6.1.4.1.637.3.1.8.5.1.5		not-accessible	This is the FRANP Signalling table. It will exists once per FRANP Signalling instance on each LT.
adnFrtSiEntry	1.3.6.1.4.1.637.3.1.8.5.1.5.1		not-accessible	One instance of the adnFrtSiTable. There will be one instance for each FRANP Signalling on each LT.
INT adnFrtSiTraceIndex	1.3.6.1.4.1.637.3.1.8.5.1.5.1.1	INTEGER	read-only	This entry represents the current instance or index. It is provided in order to be able to dump each Franp_si trace instance of each object.
INT adnFrtSiTraceCntl	1.3.6.1.4.1.637.3.1.8.5.1.5.1.2	INTEGER	read-write	This object provides a mechanism for controlling Franp Signalling ability to enable/disable tracing data from its Bus side, Trunk side, and Ism side. The following are the possible values it can hold. 1 - Trace activity enabled 2 - Trace activity disabled (default setting)
INT adnFrtSiTraceSize	1.3.6.1.4.1.637.3.1.8.5.1.5.1.3	INTEGER	read-write	This object provides a mechanism for defining the number of entries the Franp Signalling trace area can have. Be aware when issuing a set command to modify this value, any existing trace data will be lost to make room for the new trace block size.
OCT adnFrtSiTraceArea	1.3.6.1.4.1.637.3.1.8.5.1.5.1.4	OCTET STRING	read-only	This is the internal BINARY message trace entry maintained by FRANP_SI for its 3 main interfaces, (Bus side, Trunk side, and Ism side). This entry is instanciated by AdnFrtSiInstance index that comprises the entire trace area table. The FRANP Signalling software is implemented as a Finite State Machine, and all message events received are stored here. It is placed here for maintenance purposes only.
OCT adnFrtSiStat	1.3.6.1.4.1.637.3.1.8.5.1.5.1.5	OCTET STRING	read-only	This is the internal FRANP_SI data structure. This will contain internal error counters and structures. This is the internal table maintained by FRANP_SI.
OCT adnFrtSiStatISMTrace	1.3.6.1.4.1.637.3.1.8.5.1.5.1.6	OCTET STRING	read-only	This is the ISM message trace area. All ISM Messages transmitted and received by FRANP_SI are stored here. It is placed here for maintenance purposes only.
adnFrtSwTable	1.3.6.1.4.1.637.3.1.8.5.1.6		not-accessible	This is the FRANP_SW table. It will exists once per FRANP_SW instance on each LT.
adnFrtSwEntry	1.3.6.1.4.1.637.3.1.8.5.1.6.1		not-accessible	One instance of the adnFrtSwTable. There will be one instance for each FRANP_SW on each LT.
OCT adnFrtSwStatFRSI	1.3.6.1.4.1.637.3.1.8.5.1.6.1.1	OCTET STRING	read-only	This is the internal FRSI data structure. This will contain internal error counters and structures. This is the internal table maintained by FRSI component of FRANP_SW.
OCT adnFrtSwStatIWF	1.3.6.1.4.1.637.3.1.8.5.1.6.1.2	OCTET STRING	read-only	This is the internal IWF data structure. This will contain internal error counters and structures. This is the internal table maintained by IWF component of FRANP_SW.
OCT adnFrtSwStatISMTrace	1.3.6.1.4.1.637.3.1.8.5.1.6.1.3	OCTET STRING	read-only	This is the ISM message trace area. All ISM Messages transmitted and received by FRSI component of FRANP_SW are stored here. It is placed here for maintenance purposes only.
adnFrsEnvMIB	1.3.6.1.4.1.637.3.1.8.5.2
adnFrChanPrivateTable	1.3.6.1.4.1.637.3.1.8.5.2.1		not-accessible	This table is an extension of the Frame Relay Management Signalling Group table and the Frame Relay Logical Port Group table from RFC1604.
adnFrChanPrivateEntry	1.3.6.1.4.1.637.3.1.8.5.2.1.1		not-accessible	An entry in the Channel Table. There will be one entry for each FRS channel configured
OCT adnFrChanPrivateSwitch	1.3.6.1.4.1.637.3.1.8.5.2.1.1.1	OCTET STRING	read-only	This is the BINARY internal channel structure maintained by FRS_SW. It is placed here for maintenance purposes only.
OCT adnFrChanPrivateSignalling	1.3.6.1.4.1.637.3.1.8.5.2.1.1.2	OCTET STRING	read-only	This is the BINARY internal channel structure maintained by FRS_SI. It is placed here for maintenance purposes only.
OCT adnFrChanPrivateSwMsgtrace	1.3.6.1.4.1.637.3.1.8.5.2.1.1.3	OCTET STRING	read-only	This is the internal BINARY message trace table maintained by FRS_SW for this channel. The FRS_SW software is implemented as a Finite State Machine, and all events received and their corresponding states are stored here. It is placed here for maintenance purposes only.
OCT adnFrChanPrivateSiMsgtrace	1.3.6.1.4.1.637.3.1.8.5.2.1.1.4	OCTET STRING	read-only	This is the internal BINARY message trace table maintained by Channel Management portion of FRS_SI for this VC. The Channel Management software is implemented as a Finite State Machine, and all events received and their corresponding states are stored here. It is placed here for maintenance purposes only.
adnFrVCPrivateTable	1.3.6.1.4.1.637.3.1.8.5.2.2		not-accessible	This is the PVC table extensions. The PVC End-Point Table in RFC1604 is not sufficient for our HSS network. These fields are the extensions to it
adnFrVCPrivateEntry	1.3.6.1.4.1.637.3.1.8.5.2.2.1		not-accessible	PVC table entry
OCT adnFrVCPrivateSwitch	1.3.6.1.4.1.637.3.1.8.5.2.2.1.1	OCTET STRING	read-only	This is the BINARY internal PVC structure maintained by FRS_SW. It is placed here for maintenance purposes only.
OCT adnFrVCPrivateSignalling	1.3.6.1.4.1.637.3.1.8.5.2.2.1.2	OCTET STRING	read-only	This is the BINARY internal PVC structure maintained by FRS_SI. It is placed here for maintenance purposes only.
OCT adnFrVCPrivateSwMsgtrace	1.3.6.1.4.1.637.3.1.8.5.2.2.1.3	OCTET STRING	read-only	This is the internal BINARY message trace table maintained by FRS_SW for this VC. The FRS_SW software is implemented as a Finite State Machine, and all events received and their corresponding states are stored here. It is placed here for maintenance purposes only.
OCT adnFrVCPrivateSiMsgtrace	1.3.6.1.4.1.637.3.1.8.5.2.2.1.4	OCTET STRING	read-only	This is the internal BINARY message trace table maintained by PVC handler portion of FRS_SI for this VC. The PVC handler software is implemented as a Finite State Machine, and all events received and their corresponding states are stored here. It is placed here for maintenance purposes only.
adnFrTable	1.3.6.1.4.1.637.3.1.8.5.2.3		not-accessible	This is the FRS table. It will exists once per FRS instance on each LT.
adnFrEntry	1.3.6.1.4.1.637.3.1.8.5.2.3.1		not-accessible	One instance of the adnFRSTable. There will be one instance for each FRS on each LT.
OCT adnFrStatSignalling	1.3.6.1.4.1.637.3.1.8.5.2.3.1.1	OCTET STRING	read-only	This is the internal FRS data structure. This will contain internal error counters and structures. This is the internal table maintained by FRS_SI.
OCT adnFrStatSwitching	1.3.6.1.4.1.637.3.1.8.5.2.3.1.2	OCTET STRING	read-only	This is the internal FRS data structure. This will contain internal error counters and structures. This is the internal table maintained by FRS_SW.
OCT adnFrStatISMTrace	1.3.6.1.4.1.637.3.1.8.5.2.3.1.3	OCTET STRING	read-only	This is the ISM message trace area. All ISM Messages transmitted and received by FRS_SI are stored here.
adnLdrEnvMIB	1.3.6.1.4.1.637.3.1.8.5.3
adnLdrEnvTable	1.3.6.1.4.1.637.3.1.8.5.3.1		not-accessible	This is the LDR software building block table. Each LDR on each LT has one. It mainly contains debug information.
adnLdrEnvEntry	1.3.6.1.4.1.637.3.1.8.5.3.1.1		not-accessible	There will be one instance for each LDR on each LT.
OCT adnLdrSoftStatus	1.3.6.1.4.1.637.3.1.8.5.3.1.1.1	OCTET STRING	read-only	This is the internal LDR data structure. It contains the internal error counters and other information of the LDR Software status. This is the internal table maintained by LDR.
OCT adnLdrISMTrace	1.3.6.1.4.1.637.3.1.8.5.3.1.1.2	OCTET STRING	read-only	This is the ISM message trace area. All ISM Messages transmitted and received by FRS_SI are stored here.
adnLdrChanEnvTable	1.3.6.1.4.1.637.3.1.8.5.3.2		not-accessible	This table contains internal channel structure maintained by LDR. It is used for maintenance purposes only.
adnLdrChanEnvEntry	1.3.6.1.4.1.637.3.1.8.5.3.2.1		not-accessible	An entry in the LDR Channel Environment Table. There will be one entry for each LDR channel configured.
ADN adnLdrChanTraceFlag	1.3.6.1.4.1.637.3.1.8.5.3.2.1.1	AdnEnableDisabled	read-write	Flag indicating if trace is enabled.
OCT adnLdrChanControlData	1.3.6.1.4.1.637.3.1.8.5.3.2.1.2	OCTET STRING	read-only	This is the BINARY channel control block data structure maintained by the LDR. It is placed here for maintenance purposes only
OCT adnLdrChanCmeMsgTrace	1.3.6.1.4.1.637.3.1.8.5.3.2.1.3	OCTET STRING	read-only	This is the trace area for LDR and CME-SUP interface. The information of messages that sent and received by the LDR are stored here.
OCT adnLdrChanInmpFuncTrace	1.3.6.1.4.1.637.3.1.8.5.3.2.1.4	OCTET STRING	read-only	This is the trace area for LDR and INMP Library interface. Function call information (LDR functions called by INMP Library, and functions in INMP Library called by LDR) are recorded here.
adnIsnaEnvMib	1.3.6.1.4.1.637.3.1.8.5.4
adnIsnaIcIntTable	1.3.6.1.4.1.637.3.1.8.5.4.1		not-accessible	This is the ISNA Internal Connection diagnostic table definitions. It is an extension to the adnIsnaIcTable definitions.
adnIsnaIcIntEntry	1.3.6.1.4.1.637.3.1.8.5.4.1.1		not-accessible	Internal ISNA IC level diagnostic table. Uses indeces 'adnIsnaIcifIndex and 'adnIsnaIcDlci' defined in 'adnIsnaIcTable' table.
INT adnIsnaIcIntifIndex	1.3.6.1.4.1.637.3.1.8.5.4.1.1.1	INTEGER	read-only	This object defines the 1st half of the Internal Connection defined in the 'adnIsnaIcTable' and is one to one mapping to 'adnIsnaIcifIndex' object.
INT adnIsnaIcIntDlci	1.3.6.1.4.1.637.3.1.8.5.4.1.1.2	INTEGER	read-only	This object defines the 2nd half of the Internal Connection defined in the 'adnIsnaIcTable' and is one to one mapping to 'adnIsnaIcDlci' object.
CTR adnIsnaIcIpOutPkts	1.3.6.1.4.1.637.3.1.8.5.4.1.1.3	Counter	read-only	The total number of packets transmitted by ISNA to the IP layer that are associated with a given Internal Connection
CTR adnIsnaIcIpInPkts	1.3.6.1.4.1.637.3.1.8.5.4.1.1.4	Counter	read-only	The total number of packets received by ISNA from the IP layer that are associated with a given Internal Connection
CTR adnIsnaIcIssOutPkts	1.3.6.1.4.1.637.3.1.8.5.4.1.1.5	Counter	read-only	The total number of ISS status packets transmitted by ISNA to ISOM that are associated with a given Internal Connection
CTR adnIsnaIcIssInPkts	1.3.6.1.4.1.637.3.1.8.5.4.1.1.6	Counter	read-only	The total number of ISS status packets received by ISNA from ISOM that are associated with a given Internal Connection
CTR adnIsnaIcIcmpIntPkts	1.3.6.1.4.1.637.3.1.8.5.4.1.1.7	Counter	read-only	The total number of ICMP packets received by ISNA from the local IP layer that are associated with a given Internal Connection
CTR adnIsnaIcIcmpExtPkts	1.3.6.1.4.1.637.3.1.8.5.4.1.1.8	Counter	read-only	The total number of ICMP packets transmitted by ISNA to the local IP layer that are associated with a given Internal Connection
CTR adnIsnaIcIpOutDiscards	1.3.6.1.4.1.637.3.1.8.5.4.1.1.9	Counter	read-only	The total number of IP packets destined to IP layer, discarded due to internal IP access failures or system resources errors. All packets discarded are associated with a given Internal Connection.
CTR adnIsnaIcIpInDiscards	1.3.6.1.4.1.637.3.1.8.5.4.1.1.10	Counter	read-only	The total number of IP packets received from IP layer, discarded due to internal ICS access failures or system resources errors. All packets discarded are associated with a given Internal Connection.
OCT adnIsnaIcIcbMsgtrace	1.3.6.1.4.1.637.3.1.8.5.4.1.1.11	OCTET STRING	read-only	This is the internal BINARY message trace table maintained by ISNA for this IC/PVC. The ISNA software is implemented as a Finite State Machine, and all events received and their corresponding states are stored here. It is placed here for maintenance purposes only.
adnIsnaIpTable	1.3.6.1.4.1.637.3.1.8.5.4.2		not-accessible	This is the ISNA IP diagnostic table definitions.
adnIsnaIpEntry	1.3.6.1.4.1.637.3.1.8.5.4.2.1		not-accessible	ISNA IP Trafic counters level diagnostic table. Uses index 'adnIsnaIpIndex' defined in 'adnIsnaIpTable' table.
INT adnIsnaIpIndex	1.3.6.1.4.1.637.3.1.8.5.4.2.1.1	INTEGER	read-only	This object is mapped to adnIsnaIpIndex in the adnIsnaIpTable.
CTR adnIsnaIpNumOfLpx	1.3.6.1.4.1.637.3.1.8.5.4.2.1.2	Counter	read-only	The total number of LPXs (logical processor index) in IIRT (IP ISNA routing table) table.
CTR adnIsnaIpNumOfInterface	1.3.6.1.4.1.637.3.1.8.5.4.2.1.3	Counter	read-only	The total number of Interfaces in IIRT (IP ISNA routing table) table.
CTR adnIsnaIpNumOfVc	1.3.6.1.4.1.637.3.1.8.5.4.2.1.4	Counter	read-only	The total number of VCs in IIRT (IP ISNA routing table) table.
CTR adnIsnaIpIpOutPkts	1.3.6.1.4.1.637.3.1.8.5.4.2.1.5	Counter	read-only	The total number of packets transmitted by ISNA_IP to the IP layer.
CTR adnIsnaIpIpInPkts	1.3.6.1.4.1.637.3.1.8.5.4.2.1.6	Counter	read-only	The total number of packets received by ISNA_IP from the IP layer.
CTR adnIsnaIpIpDiscards	1.3.6.1.4.1.637.3.1.8.5.4.2.1.7	Counter	read-only	The total number of discarded IP packets coming from IP layer.
CTR adnIsnaIpIpomOutPkts	1.3.6.1.4.1.637.3.1.8.5.4.2.1.9	Counter	read-only	The total number of packets transmitted by ISNA_IP to IPOM sybsystem.
CTR adnIsnaIpIpomInPkts	1.3.6.1.4.1.637.3.1.8.5.4.2.1.10	Counter	read-only	The total number of packets received by ISNA_IP from IPOM subsytem.
CTR adnIsnaIpIpomDiscards	1.3.6.1.4.1.637.3.1.8.5.4.2.1.11	Counter	read-only	The total number of discarded IP packets comming from IPOM subsystem.
CTR adnIsnaIpRdssInPkts	1.3.6.1.4.1.637.3.1.8.5.4.2.1.13	Counter	read-only	The total number of packets received by ISNA_IP from RDSS subsytem.
CTR adnIsnaIpRdssOutPkts	1.3.6.1.4.1.637.3.1.8.5.4.2.1.14	Counter	read-only	The total number of packets transmitted by ISNA_IP to RDSS sybsystem.
CTR adnIsnaIpRdssDiscards	1.3.6.1.4.1.637.3.1.8.5.4.2.1.15	Counter	read-only	The total number of discarded IP packets comming from RDSS subsystem.
adnIsnaIpIirtTable	1.3.6.1.4.1.637.3.1.8.5.4.3		not-accessible	This is the ISNA IP IIRT (IP ISNA routing table) tree table definitions.
adnIsnaIpIirtEntry	1.3.6.1.4.1.637.3.1.8.5.4.3.1		not-accessible	ISNA IP IIRT (IP ISNA routing table) tree entry table. Uses index 'adnIsnaIpIirtIpaddrs' defined in 'adnIsnaIpIirtTable' table.
IP adnIsnaIpIirtIpaddrs	1.3.6.1.4.1.637.3.1.8.5.4.3.1.1	IpAddress	read-only	The next hop IP address .
INT adnIsnaIpIirtVcNum	1.3.6.1.4.1.637.3.1.8.5.4.3.1.2	INTEGER	read-only	The VC number on the local Interface, The NHIPA (next hop IP address) apply to the remote interface which the VC is connecting.
INT adnIsnaIpIirtIfIndex	1.3.6.1.4.1.637.3.1.8.5.4.3.1.3	INTEGER	read-only	The ifindex Interface at the local machine.
INT adnIsnaIpIirtLpxNum	1.3.6.1.4.1.637.3.1.8.5.4.3.1.5	INTEGER	read-only	The LPX (logical processor index) local which the interface is configured on.
INT adnIsnaIpIirtSesid	1.3.6.1.4.1.637.3.1.8.5.4.3.1.6	INTEGER	read-only	The session id which IP packet is routed to.
INT adnIsnaIpIirtVcState	1.3.6.1.4.1.637.3.1.8.5.4.3.1.7	INTEGER	read-only	The status of the VC (up or down) which associate with NHIPA (next hop IP address.
adnNodeSupervisionEnvMIB	1.3.6.1.4.1.637.3.1.8.5.5
adnBoardMiscTable	1.3.6.1.4.1.637.3.1.8.5.5.1		not-accessible	This is the board miscellaneous characteristics table.
adnBoardMiscEntry	1.3.6.1.4.1.637.3.1.8.5.5.1.1		not-accessible	An entry in the Board Miscellaneous characteristics Table. There is one entry for each Board. The index corresponds to equipment type 'card' in the adnEquipTable.
OCT adnBoardMiscISL	1.3.6.1.4.1.637.3.1.8.5.5.1.1.1	OCTET STRING	read-only	This object contains the characteristics of the board retrieved through the ISL link. This object is a dump of 256 bytes of the EEPROM of the board, It contains information called 'group 2' information. The signification of each byte is detailed in the document 8BA00940001ASZZA. When the board is not plugged in, the value of this object is 00 00 00 00 ( that is, an octet string of length 4, with each octet having a zero decimal value).
adnAtmBoardErrCounterTable	1.3.6.1.4.1.637.3.1.8.5.5.2		not-accessible	This table is the ATM boards error counter table. Each counter corresponds to a defect number identified by a bit set in the adnAtmBoardASEStatus for ASe board, the adnAtmBoardCIGStatus for CIG board and the adnAtmBoardHSCStatus for HSC board. These nominators are defined in the adnAtmBoardErCounterTable. The counters are classified according to the board type. Some are specific to the broadband ATM switching element (BBASE) board also called the matrix board.
adnAtmBoardErrCounterEntry	1.3.6.1.4.1.637.3.1.8.5.5.2.1		not-accessible	An entry in the ATM boards error counter table.
CTR adnAtmBoardErrUFOFCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.1	Counter	read-only	The counter associated with the number of user FIFO overflows; counter #0 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAtmBoardErrUFRFCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.2	Counter	read-only	The counter associated with the number of user FIFO read failures; counter #1 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAtmBoardErrNFOFCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.3	Counter	read-only	The counter associated with the number of network FIFO overflows; counter #2 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAtmBoardErrPHTRAMPCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.4	Counter	read-only	The counter associated with the number of BGPHT chip RAM parity errors; counter #3 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAtmBoardErrNFRFCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.5	Counter	read-only	The counter associated with the number of network FIFO read failures; counter #4 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAtmBoardErrNAVCCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.6	Counter	read-only	The counter associated with the number of cells received on non active VC; counter #5 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAtmBoardErrNAVPCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.7	Counter	read-only	The counter associated with the number of cells received on non active VP; counter #6 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAtmBoardErrRBOFCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.8	Counter	read-only	The counter associated with the number of reception buffer overflows; counter #7 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAtmBoardErrQRP0RAMPCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.9	Counter	read-only	The counter associated with the number of QRP 0 chip RAM parity errors; counter #14 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP0DMACounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.10	Counter	read-only	The counter associated with the number of QRP 0 chip DMA errors; counter #15 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP0FIFOCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.11	Counter	read-only	The counter associated with the number of QRP 0 chip extraction FIFO overflows; counter #16 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP1RAMPCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.12	Counter	read-only	The counter associated with the number of QRP 1 chip RAM parity errors; counter #17 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP1DMACounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.13	Counter	read-only	The counter associated with the number of QRP 1 chip DMA errors; counter #18 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP1FIFOCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.14	Counter	read-only	The counter associated with the number of QRP 1 chip extraction FIFO overflows; counter #19 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP2RAMPCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.15	Counter	read-only	The counter associated with the number of QRP 2 chip RAM parity errors; counter #20 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP2DMACounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.16	Counter	read-only	The counter associated with the number of QRP 2 chip DMA errors; counter #21 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP2FIFOCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.17	Counter	read-only	The counter associated with the number of QRP 2 chip extraction FIFO overflows; counter #22 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP3RAMPCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.18	Counter	read-only	The counter associated with the number of QRP 3 chip RAM parity errors; counter #23 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP3DMACounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.19	Counter	read-only	The counter associated with the number of QRP 3 chip DMA errors; counter #24 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrQRP3FIFOCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.20	Counter	read-only	The counter associated with the number of QRP 3 chip extraction FIFO overflows; counter #25 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrHMP0LLPCCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.21	Counter	read-only	The counter associated with the number of low priority cells lost due to SCD; counter #26 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrHMP0LHPCCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.22	Counter	read-only	The counter associated with the number of high priority cells lost due to buffer overflow(FULC); counter #27 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrHMP0SYNCCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.23	Counter	read-only	The counter associated with the number of fault synchronization in the HMP 0 chip; counter #28 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrHMP1LLPCCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.24	Counter	read-only	The counter associated with the number of low priority cells lost in the HMP 1 chip; counter #29 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrHMP1LHPCCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.25	Counter	read-only	The counter associated with the number of high priority cells lost in the HMP 1 chip; counter #30 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardErrHMP1SYNCCounter	1.3.6.1.4.1.637.3.1.8.5.5.2.1.26	Counter	read-only	The counter associated with the number of fault synchronization in the HMP 1 chip; counter #31 of the ATM core; this counter is only relevant for the matrix board.
adnAtmBoardTrCounterTable	1.3.6.1.4.1.637.3.1.8.5.5.3		not-accessible	This table is the ATM boards traffic counter table. The counters are classified according to the board type. Some are specific to the broadband ATM switching element (BBASE) board also called the matrix board.
adnAtmBoardTrCounterEntry	1.3.6.1.4.1.637.3.1.8.5.5.3.1		not-accessible	An entry in the ATM boards traffic counter table.
CTR adnAtmBoardTrHMP0MTCounter	1.3.6.1.4.1.637.3.1.8.5.5.3.1.1	Counter	read-only	The counter associated with the observation threshold 1 crossing of the HMP 0 chip; counter #0 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAtmBoardTrHMP1MTCounter	1.3.6.1.4.1.637.3.1.8.5.5.3.1.2	Counter	read-only	The counter associated with the observation threshold 2 crossing of the HMP 1 chip; counter #1 of the ATM core; this counter is only relevant for the matrix board.
GAU adnAtmBoardTrFPTMICICounter	1.3.6.1.4.1.637.3.1.8.5.5.3.1.3	Gauge	read-only	The counter associated with the number of free outgoing point-to-multipoint (PTM) internal channel identifiers (ICI); counter #2 of the ATM core; this counter is only relevant for the matrix board.
adnAeiPortErrCounterTable	1.3.6.1.4.1.637.3.1.8.5.5.4		not-accessible	This table is the ATM electrical interface (AEI) port error counter table. Each counter corresponds to a defect number identified by a bit set in the adnAtmPortASEStatus for ASe board, the adnAtmPortCIGStatus for CIG board and the adnAtmPortHSCStatus for HSC board. These nominators are defined in the adnAtmPortErCounterTable. The counters are classified according to the board type. Some are specific to the broadband ATM switching element (BBASE) board also called the matrix board.
adnAeiPortErrCounterEntry	1.3.6.1.4.1.637.3.1.8.5.5.4.1		not-accessible	An entry in the ATM electrical interface (AEI) port error counter table.
CTR adnAeiPortErrOOSCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.1	Counter	read-only	The counter associated with the out of synchronization intervals; counter #0 of the ATM core.
CTR adnAeiPortErrLOSCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.2	Counter	read-only	The counter associated with the loss of synchronization intervals; counter #1 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAeiPortErrNFOFCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.3	Counter	read-only	The counter associated with the number of network FIFO overflows; counter #2 of the ATM core.
CTR adnAeiPortErrIEMRAMPCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.4	Counter	read-only	The counter associated with the number of BGIEM chip RAM parity errors; counter #3 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrCECHCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.5	Counter	read-only	The counter associated with the number of correctable errors on cells header; counter #4 of the ATM core.
CTR adnAeiPortErrUCECHCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.6	Counter	read-only	The counter associated with the number of uncorrectable errors on cells header; counter #5 of the ATM core.
CTR adnAeiPortErrCRCMA1Counter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.7	Counter	read-only	The counter associated with the number of CRC errors on payload field of maintenance active cells of type 1 (MA1); counter #6 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrCRCSICCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.8	Counter	read-only	The counter associated with the number of CRC errors on payload field of self identified cells (SIC); counter #7 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrNPECounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.9	Counter	read-only	The counter associated with the number of parity errors on payload field of cells; counter #8 of the ATM core.
CTR adnAeiPortErrRTAGCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.10	Counter	read-only	The counter associated with the number of unallowed routing tags; counter #9 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAeiPortErrNMA1Counter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.11	Counter	read-only	The counter associated with the number of lost data maintenance cells; counter #12 of the ATM core.
CTR adnAeiPortErrEMA1Counter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.12	Counter	read-only	The counter associated with the number of data maintenance cells received with error; counter #14 of the ATM core.
CTR adnAeiPortErrNSFOFCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.13	Counter	read-only	The counter associated with the number of network/signalling FIFO overflows; counter #17 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrNFWFCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.14	Counter	read-only	The counter associated with the number of network FIFO write failures; counter #18 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrSFWFCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.15	Counter	read-only	The counter associated with the number of signalling FIFO write failures; counter #19 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrNSFRFCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.16	Counter	read-only	The counter associated with the number of network/signalling FIFO read failures; counter #20 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrUSFRFCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.17	Counter	read-only	The counter associated with the number of user/signalling FIFO read failures; counter #22 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrUFWFCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.18	Counter	read-only	The counter associated with the number of user FIFO write failures; counter #23 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrUSFOFCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.19	Counter	read-only	The counter associated with the number of user/signalling FIFO overflows; counter #24 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrNICICounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.20	Counter	read-only	The counter associated with the number of cells received on non active internal channel identifier (ICI); counter #25 of the ATM core.
CTR adnAeiPortErrNCRCCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.21	Counter	read-only	The counter associated with the number of CRC errors on network side; counter #26 of the ATM core.
CTR adnAeiPortErrNAALCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.22	Counter	read-only	The counter associated with the number of ATM adaptation layer (AAL) sequence errors on network side; counter #27 of the ATM core.
CTR adnAeiPortErrUCRCCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.23	Counter	read-only	The counter associated with the number of CRC errors on user side; counter #28 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrUAALCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.24	Counter	read-only	The counter associated with the number of ATM adaptation layer (AAL) sequence errors on user side; counter #29 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortErrURCCounter	1.3.6.1.4.1.637.3.1.8.5.5.4.1.25	Counter	read-only	The counter associated with the number of unrouted cells; counter #30 of the ATM core; this counter is only relevant for the matrix board.
adnAeiPortTrCounterTable	1.3.6.1.4.1.637.3.1.8.5.5.5		not-accessible	This table is the ATM electrical interface (AEI) port traffic counters table. The counters are classified according to the board type. Some are specific to the broadband ATM switching element (BBASE) board also called the matrix board.
adnAeiPortTrCounterEntry	1.3.6.1.4.1.637.3.1.8.5.5.5.1		not-accessible	An entry in the ATM electrical interface (AEI) port traffic counters table.
CTR adnAeiPortTrPTPSetRqCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.1	Counter	read-only	The counter associated with the number of point-to-point (PTP) setup requests; counter #1 of the ATM core.
CTR adnAeiPortTrPTMSetRqCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.2	Counter	read-only	The counter associated with the number of point-to-multipoint (PTM) setup requests; counter #2 of the ATM core.
CTR adnAeiPortTrPTPSetRjBCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.3	Counter	read-only	The counter associated with the number of point-to-point (PTP) setup rejects due to blocking; counter #3 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortTrPTMSetRjBCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.4	Counter	read-only	The counter associated with the number of point-to-multipoint (PTM) setup rejects due to blocking; counter #4 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortTrPTPSetRjCCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.5	Counter	read-only	The counter associated with the number of point-to-point (PTP) setup rejects due to communication; counter #5 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortTrPTMSetRjCCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.6	Counter	read-only	The counter associated with the number of point-to-multipoint (PTM) setup rejects due to communication; counter #6 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortTrPTPSetTrCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.7	Counter	read-only	The counter associated with the number of point-to-point (PTP) setup trials; counter #7 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortTrPTMSetTrCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.8	Counter	read-only	The counter associated with the number of point-to-multipoint (PTM) setup trials; counter #8 of the ATM core; this counter is not relevant for the matrix board.
GAU adnAeiPortTrPTPCnxCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.9	Gauge	read-only	The counter associated with the number of point-to-point (PTP) connections in progress; counter #13 of the ATM core; this counter is not relevant for the matrix board.
GAU adnAeiPortTrPTMCnxCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.10	Gauge	read-only	The counter associated with the number of point-to-multipoint (PTM) connections in progress; counter #14 of the ATM core; this counter is not relevant for the matrix board.
CTR adnAeiPortTrPTPBWICIRqCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.11	Counter	read-only	The counter associated with the number of point-to-point (PTP) bandwith or internal channel identifier (BW,ICI) requests; counter #4 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAeiPortTrPTMBWICIRqCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.12	Counter	read-only	The counter associated with the number of point-to-multipoint (PTM) bandwith or internal channel identifier (BW,ICI) requests; counter #5 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAeiPortTrPTPBWRjCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.13	Counter	read-only	The counter associated with the number of point-to-point (PTP) bandwith (BW) requests failure; counter #6 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAeiPortTrPTMBWRjCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.14	Counter	read-only	The counter associated with the number of point-to-multipoint (PTM) bandwith (BW) requests failure; counter #7 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAeiPortTrPTPICIRjCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.15	Counter	read-only	The counter associated with the number of point-to-point (PTP) internal channel identifier (ICI) requests failure; counter #8 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAeiPortTrPTMICIRjCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.16	Counter	read-only	The counter associated with the number of point-to-multipoint (PTM) internal channel identifier (ICI) requests failure; counter #9 of the ATM core; this counter is only relevant for the matrix board.
GAU adnAeiPortTrPeakBWCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.17	Gauge	read-only	The counter associated with the reserved peak bandwith (BW); counter #10 of the ATM core; this counter is only relevant for the matrix board.
GAU adnAeiPortTrFPTPICICounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.18	Gauge	read-only	The counter associated with the number of free point-to-point (PTP) internal channel identifiers (ICI); counter #12 of the ATM core; this counter is only relevant for the matrix board.
GAU adnAeiPortTrMPriorBWCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.19	Gauge	read-only	The counter associated with the reserved mean priority bandwith (BW); Counter #14 of the ATM core; this counter is only relevant for the matrix board.
CTR adnAeiPortTrInCellsCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.20	Counter	read-only	The counter associated with the number of incoming cells; counter #15 of the ATM core.; this counter is only relevant for the matrix board.
CTR adnAeiPortTrOutCellsCounter	1.3.6.1.4.1.637.3.1.8.5.5.5.1.21	Counter	read-only	The counter associated with the number of outgoing cells; counter #16 of the ATM core; this counter is only relevant for the matrix board.
adnAtmBoardDefTable	1.3.6.1.4.1.637.3.1.8.5.5.20		not-accessible	This table is the ATM boards defects table. Some defects characteristics are updatable. Matrix board case: all the defects are only readable.
adnAtmBoardDefEntry	1.3.6.1.4.1.637.3.1.8.5.5.20.1		not-accessible	An entry in the ATM boards defects table. There will be one entry for each defect (i.e error/warning) configured. Notice that according to the defect number, default value of each parameter of the instance may be different between two instances.
INT adnAtmBoardDefBoardType	1.3.6.1.4.1.637.3.1.8.5.5.20.1.1	INTEGER	read-only	This is the ATM board type.
INT adnAtmBoardDefNumber	1.3.6.1.4.1.637.3.1.8.5.5.20.1.2	INTEGER	read-only	This indicates the defect number. The description of each defect is given via the adnAtmBoardErASEStatus for ASE board, the adnAtmBoardErHSCStatus for HSC board, the adnAtmBoardErCIGStatus for CIG board. These nominators are defined in the adnAtmBoardErTable. There's a one to one mapping between the bit position and the defect number.
INT adnAtmBoardDefEventClass	1.3.6.1.4.1.637.3.1.8.5.5.20.1.3	INTEGER	read-only	This indicates the event class from hardware side: event: single fault signalled by the hardware or another software module to the supervision antenna inside the coupler board. No end is signalled, the presence of the fault can't be checked. status: the beginning of the fault is signalled to the supervision antenna inside the coupler board; the presence of the fault can be checked. statusc: the hardware provides no interrupt; this status is periodically scanned by the supervision antenna inside the coupler board. counter: a n bit long hardware counter counts the elementary events; an interrupt is generally sent at saturation; its value can be read; it is reset to zero when read.
INT adnAtmBoardDefBegThreshold	1.3.6.1.4.1.637.3.1.8.5.5.20.1.4	INTEGER	read-write	This indicates the number of times an error is detected within a time period (defined by adnAtmBoardDefBegTimer) before an event (beginning of error) is generated and an error condition is entered.
INT adnAtmBoardDefEndThreshold	1.3.6.1.4.1.637.3.1.8.5.5.20.1.5	INTEGER	read-write	This indicates the maximum number of times a condition may be detected within a time period (defined by adnAtmBoardDefEndTimer) before an event (ending of error) is generated and an error condition is cleared.
INT adnAtmBoardDefBegTimer	1.3.6.1.4.1.637.3.1.8.5.5.20.1.6	INTEGER	read-write	This indicates the beginning timer in milliseconds during which the first appearance of an error is controlled.
INT adnAtmBoardDefEndTimer	1.3.6.1.4.1.637.3.1.8.5.5.20.1.7	INTEGER	read-write	This indicates the end timer in milliseconds during which the disappearance of an error is controlled.
INT adnAtmBoardDefSignalling	1.3.6.1.4.1.637.3.1.8.5.5.20.1.8	INTEGER	read-write	This indicates the defect signalling in addition to the report towards the control unit (CU). It is coded as a bit map. The various bit positions are: 1 : ERI (error indicator, bit inserted in the active maintenance cells to warn neighbour boards that an error is detected), 2 : P-FERF or RDI-P (path section far end received failure indication sent to the origin of the defect), 4 : MS-FERF or RDI-L (multiplexing section far end received failure indication sent to the origin of the defect), 8 : ATM-AIS (alarm indication signal is sent on a line defect towards the network handler dealing with VP/VC AIS management), 16 : RAI (remote alarm indication), 32 : RLED (the status led must be set permanent red).
INT adnAtmBoardDefErrOrWng	1.3.6.1.4.1.637.3.1.8.5.5.20.1.9	INTEGER	read-write	This indicates the defect type (i.e error or warning); an error is a critical defect which modifies the operational state of the object.
INT adnAtmBoardDefReportEnable	1.3.6.1.4.1.637.3.1.8.5.5.20.1.10	INTEGER	read-write	This indicates the report control of the defect towards the control unit (CU).
adnAeiPortDefTable	1.3.6.1.4.1.637.3.1.8.5.5.21		not-accessible	This table is the ATM electrical interface (AEI) port defects table. Some defects characteristics are updatable. Matrix board case: all the defects are only readable.
adnAeiPortDefEntry	1.3.6.1.4.1.637.3.1.8.5.5.21.1		not-accessible	An entry in the ATM electrical interface (AEI) port defects table. There will be one entry for each defect (i.e error/warning) configured. Notice that according to the defect number, default value of each parameter of the instance may be different between two instances.
INT adnAeiPortDefBoardType	1.3.6.1.4.1.637.3.1.8.5.5.21.1.1	INTEGER	read-only	This is the ATM board type.
INT adnAeiPortDefNumber	1.3.6.1.4.1.637.3.1.8.5.5.21.1.2	INTEGER	read-only	This indicates the defect number. The description of each defect is given via the adnAtmPortErASEStatus for ASE board, the adnAtmPortErHSCStatus for HSC board, the adnAtmPortErCIGStatus for CIG board. These nominators are defined in the adnAtmPortErTable. There's a one to one mappingbetween the bit position the defect number.
INT adnAeiPortDefEventClass	1.3.6.1.4.1.637.3.1.8.5.5.21.1.3	INTEGER	read-only	This indicates the event class from hardware side: event: single fault signalled by the hardware or another software module to the supervision antenna inside the coupler board. No end is signalled, the presence of the fault can't be checked. status: the beginning of the fault is signalled to the supervision antenna inside the coupler board; the presence of the fault can be checked. statusc: the hardware provides no interrupt; this status is periodically scanned by the supervision antenna inside the coupler board. counter: a n bit long hardware counter counts the elementary events; an interrupt is generally sent at saturation; its value can be read; it is reset to zero when read.
INT adnAeiPortDefDirection	1.3.6.1.4.1.637.3.1.8.5.5.21.1.4	INTEGER	read-only	This indicates the direction of the defect when it occurs.
INT adnAeiPortDefBegThreshold	1.3.6.1.4.1.637.3.1.8.5.5.21.1.5	INTEGER	read-write	This indicates the number of times an error is detected within a time period (defined by adnAeiPortDefBegTimer) before an event (beginning of error) is generated and an error condition is entered.
INT adnAeiPortDefEndThreshold	1.3.6.1.4.1.637.3.1.8.5.5.21.1.6	INTEGER	read-write	This indicates the maximum number of times a condition may be detected within a time period (defined by adnAeiPortDefEndTimer) before an event (ending of error) is generated and an error condition is cleared.
INT adnAeiPortDefBegTimer	1.3.6.1.4.1.637.3.1.8.5.5.21.1.7	INTEGER	read-write	This indicates the beginning timer in milliseconds during which the first appearance of an error is controlled.
INT adnAeiPortDefEndTimer	1.3.6.1.4.1.637.3.1.8.5.5.21.1.8	INTEGER	read-write	This indicates the end timer in milliseconds during which the disappearance of an error is controlled.
INT adnAeiPortDefSignalling	1.3.6.1.4.1.637.3.1.8.5.5.21.1.9	INTEGER	read-write	This indicates the defect signalling in addition to the report towards the control unit (CU). It is coded as a bit map. The various bit positions are: 1 : ERI (error indicator, bit inserted in the active maintenance cells to warn neighbour boards that an error is detected), 2 : P-FERF or RDI-P (path section far end received failure indication sent to the origin of the defect), 4 : MS-FERF or RDI-L (multiplexing section far end received failure indication sent to the origin of the defect), 8 : ATM-AIS (alarm indication signal is sent on a line defect towards the network handler dealing with VP/VC AIS management), 16 : RAI (remote alarm indication), 32 : RLED (the status led must be set permanent red).
INT adnAeiPortDefErrOrWng	1.3.6.1.4.1.637.3.1.8.5.5.21.1.10	INTEGER	read-write	This indicates the defect type (i.e error or warning); an error is a critical defect which modifies the operational state of the object.
INT adnAeiPortDefReportEnable	1.3.6.1.4.1.637.3.1.8.5.5.21.1.11	INTEGER	read-write	This indicates the report control of the defect towards the control unit (CU).
adnAtmLineDefTable	1.3.6.1.4.1.637.3.1.8.5.5.22		not-accessible	This table is the ATM line defects table.
adnAtmLineDefEntry	1.3.6.1.4.1.637.3.1.8.5.5.22.1		not-accessible	An entry in the ATM line errors/warnings and defects table. There will be one entry for each defect (error/warning) configured. Notice that according to the defect number, default value of each parameter of the instance may be different between two instances.
INT adnAtmLineDefLineType	1.3.6.1.4.1.637.3.1.8.5.5.22.1.1	INTEGER	read-only	This is the line type.
INT adnAtmLineDefNumber	1.3.6.1.4.1.637.3.1.8.5.5.22.1.2	INTEGER	read-only	This indicates the defect number.
INT adnAtmLineDefEventClass	1.3.6.1.4.1.637.3.1.8.5.5.22.1.3	INTEGER	read-only	This indicates the event class from hardware side: event: single fault signalled by the hardware or another software module to the supervision antenna inside the coupler board. No end is signalled, the presence of the fault can't be checked. status: the beginning of the fault is signalled to the supervision antenna inside the coupler board; the presence of the fault can be checked. statusc: the hardware provides no interrupt; this status is periodically scanned by the supervision antenna inside the coupler board. counter: a n bit long hardware counter counts the elementary events; an interrupt is generally sent at saturation; its value can be read; it is reset to zero when read.
INT adnAtmLineDefUseInPerfCalcul	1.3.6.1.4.1.637.3.1.8.5.5.22.1.4	INTEGER	read-write	This indicates if the defect is used or not in performance calculation. If the defect is used for the performance calculation (i.e DefUseInPerfCalcul = yes), then the type of this defect (DefPerfType) from performance side can be either: defect: then, each occurence of the defect contributes to the performance calculation, counter: then, a counter is used to take into account this defect in performance calculation when the threshold defined by DefPerfThr is reached.
INT adnAtmLineDefPerfType	1.3.6.1.4.1.637.3.1.8.5.5.22.1.5	INTEGER	read-only	This indicates the performance type : counter: a counter is used to take into account this defect in performance calculation when the threshold defined by DefPerfThr is reached, defect: each occurence of the defect contributes to the performance calculation, defectc: each occurence of the defect contributes to the performance calculation, with counting of seconds (ANSI only).
INT adnAtmLineDefPerfThreshold	1.3.6.1.4.1.637.3.1.8.5.5.22.1.6	INTEGER	read-only	This indicates the threshold value of the performance counter.
INT adnAtmLineDefDirection	1.3.6.1.4.1.637.3.1.8.5.5.22.1.7	INTEGER	read-only	This indicates the direction of the defect when it occurs: transmit: defect on transmission direction, receive: defect on reception direction, without inhibition of transmission counters, receiveInhib: defect on reception direction, with inhibition of transmission counters.
INT adnAtmLineDefBegThreshold	1.3.6.1.4.1.637.3.1.8.5.5.22.1.8	INTEGER	read-write	This indicates the number of times an error is detected within a time period (defined by adnAtmLineDefBegTimer) before an event (beginning of error) is generated and an error condition is entered.
INT adnAtmLineDefEndThreshold	1.3.6.1.4.1.637.3.1.8.5.5.22.1.9	INTEGER	read-write	This indicates the maximum number of times a condition may be detected within a time period (defined by adnAtmLineDefEndTimer) before an event (ending of error) is generated and an error condition is cleared.
INT adnAtmLineDefBegTimer	1.3.6.1.4.1.637.3.1.8.5.5.22.1.10	INTEGER	read-write	This indicates the beginning timer in milliseconds during which the first appearance of an error is controlled.
INT adnAtmLineDefEndTimer	1.3.6.1.4.1.637.3.1.8.5.5.22.1.11	INTEGER	read-write	This indicates the end timer in milliseconds during which the disappearance of an error is controlled.
INT adnAtmLineDefSignalling	1.3.6.1.4.1.637.3.1.8.5.5.22.1.12	INTEGER	read-only	This indicates the failure signalling in addition to the report towards the control unit (CU). It is coded as a bit map. The various bit positions are: 1 : ERI (error indicator, bit inserted in the active maintenance cells to warn neighbour boards that an error is detected), 2 : P-FERF or RDI-P (path section far end received failure indication sent to the origin of the defect), 4 : MS-FERF or RDI-L (multiplexing section far end received failure indication sent to the origin of the defect), 8 : ATM-AIS (alarm indication signal is sent on a line defect towards the network handler dealing with VP/VC AIS management), 16 : RAI (remote alarm indication), 32 : RLED (the status led must be set permanent red).
INT adnAtmLineDefErrOrWng	1.3.6.1.4.1.637.3.1.8.5.5.22.1.13	INTEGER	read-write	This indicates the defect type (i.e error or warning); an error is a critical defect which modifies the operational state of the object.
INT adnAtmLineDefReportEnable	1.3.6.1.4.1.637.3.1.8.5.5.22.1.14	INTEGER	read-write	This indicates the report control of the defect towards the control unit (CU).
INT adnAtmLineDefHierarchy	1.3.6.1.4.1.637.3.1.8.5.5.22.1.15	INTEGER	read-write	This indicates the current Defect hierarchy towards the other defects; it is coded as a long integer (i.e 32 bits). There's one bit per defect: - bit #n = 0 : defect n masked (i.e the current defect inhibits the #n one if both are present), - bit #n = 1 : defect n unmasked.
INT adnAtmLineDefPerfLevel	1.3.6.1.4.1.637.3.1.8.5.5.22.1.16	INTEGER	read-only	This indicates the level at which the defect is managed: line: the defect is managed at line level, path: the defect is managed at path level.
INT adnAtmLineDefFailureSig	1.3.6.1.4.1.637.3.1.8.5.5.22.1.17	INTEGER	read-write	This indicates the failure signalling in addition to the report towards the control unit (CU). It is coded as a bit map. The various bit positions are: 1 : ERI or RSA (error indicator, bit inserted in theactive maintenance cells to warn neighbour boards that an error is detected), 2 : P-FERF or RDI-P or RAI (path section far end received failure indication sent to the origin of the defect), 4 : MS-FERF or RDI-L (multiplexing section far end received failure indication sent to the origin of the defect), 8 : ATM-AIS (alarm indication signal is sent on a line defect towards the network handler dealing with VP/VC AIS management), 32 : RLED (the status led must be set permanent red).
INT adnAtmLineDefDefectSig	1.3.6.1.4.1.637.3.1.8.5.5.22.1.18	INTEGER	read-write	This indicates the defect signalling in addition to the report towards the control unit (CU). It is coded as a bit map. The various bit positions are: 1 : ERI or RSA (error indicator, bit inserted in theactive maintenance cells to warn neighbour boards that an error is detected), 2 : P-FERF or RDI-P or RAI (path section far end received failure indication sent to the origin of the defect), 4 : MS-FERF or RDI-L (multiplexing section far end received failure indication sent to the origin of the defect), 8 : ATM-AIS (ATM alarm indication signal is sent on a line defect towards the network handler dealing with VP/VC AIS management), 32 : RLED (the status led must be set permanent red), 64 : NB-AIS (not ATM alarm indication signal is sent on a line defect towards the AEI side), 128 : TCK (trunk conditioning: in circuit emulation, a specified pattern is sent in timeslots, except TS0: a pattern for TS16, another one for other TS).
adnAtmLinePerfTable	1.3.6.1.4.1.637.3.1.8.5.5.23		not-accessible	This table is the ATM line performance parameters table.
adnAtmLinePerfEntry	1.3.6.1.4.1.637.3.1.8.5.5.23.1		not-accessible	An entry in the ATM line performance parameters table. There will be one entry for each line type.
INT adnAtmLinePerfLineType	1.3.6.1.4.1.637.3.1.8.5.5.23.1.1	INTEGER	read-only	This is the line type.
INT adnAtmLinePerfBlocksPerSec	1.3.6.1.4.1.637.3.1.8.5.5.23.1.2	INTEGER	read-only	This indicates the number of blocks sent and received per second.
INT adnAtmLinePerfLowErrBlockThr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.3	INTEGER	read-write	This indicates the low second error block threshold; the value range of this threshold is 1..adnAtmLinePerfHighErrBlockThr.
INT adnAtmLinePerfHighErrBlockThr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.4	INTEGER	read-write	This indicates the high second error block threshold; the value range of this threshold is 1..adnAtmLinePerfBlocksPerSec.
INT adnAtmLinePerfBegUnAvailable	1.3.6.1.4.1.637.3.1.8.5.5.23.1.5	INTEGER	read-write	This indicates the number of consecutive severely erroned seconds necessary to declare the beginning of an unavailable period.
INT adnAtmLinePerfEndUnAvailable	1.3.6.1.4.1.637.3.1.8.5.5.23.1.6	INTEGER	read-write	This indicates the number of consecutive non severely erroned seconds necessary to declare the ending of the unavailable period.
INT adnAtmLinePerfConsSeverErrSec	1.3.6.1.4.1.637.3.1.8.5.5.23.1.7	INTEGER	read-write	This indicates the number of consecutive severely errored seconds used for the F3 maintenance flow calculation.
INT adnAtmLinePerfHighBBE15Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.8	INTEGER	read-write	This indicates the high threshold for background block error on 1/4 hour period; the value range of this threshold is 0..900*adnAtmLinePerfHighErrBlockThr.
INT adnAtmLinePerfHighES15Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.9	INTEGER	read-write	This indicates the high threshold for errored second on 1/4 hour period; the value range of this threshold is 0..900.
INT adnAtmLinePerfHighSES15Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.10	INTEGER	read-write	This indicates the high threshold for severely errored second on 1/4 hour period; the value range of this threshold is 0..900.
INT adnAtmLinePerfLowBBE15Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.11	INTEGER	read-write	This indicates the low threshold for background block error on 1/4 hour period; the value range of this threshold is 0..adnAtmLinePerfHighBBE15Thr.
INT adnAtmLinePerfLowES15Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.12	INTEGER	read-write	This indicates the low threshold for errored second on 1/4 hour period; the value range of this threshold is 0..adnAtmLinePerfHighES15Thr.
INT adnAtmLinePerfLowSES15Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.13	INTEGER	read-write	This indicates the low threshold for severely errored second on 1/4 hour period; the value range of this threshold is 0..adnAtmLinePerfHighSES15Thr.
INT adnAtmLinePerfBBE24Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.14	INTEGER	read-write	This indicates the threshold for background block error on 24 hours period; the value range of this threshold is 0..86400*adnAtmLinePerfHighErrBlockThr.
INT adnAtmLinePerfES24Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.15	INTEGER	read-write	This indicates the threshold for errored second on 24 hours period; the value range of this threshold is 0..86400.
INT adnAtmLinePerfSES24Thr	1.3.6.1.4.1.637.3.1.8.5.5.23.1.16	INTEGER	read-write	This indicates the threshold for severely errored second on 24 hours period; the value range of this threshold is 0..86400.
adnHscBoardTrMgtEnvTable	1.3.6.1.4.1.637.3.1.8.5.5.24		not-accessible	This table is the HSC Board Traffic Management parameters table. This is only relevant for HSC boards with output buffers
adnHscBoardTrMgtEnvEntry	1.3.6.1.4.1.637.3.1.8.5.5.24.1		not-accessible	An entry in the ATM Traffic Management parameters table.
INT adnHscBoardTrMgtEnvOBLineAssig	1.3.6.1.4.1.637.3.1.8.5.5.24.1.1	INTEGER	read-only	This indicates the line number the output buffer is assigned to.
INT adnHscBoardTrMgtEnvMOBEFCIOffTh	1.3.6.1.4.1.637.3.1.8.5.5.24.1.2	INTEGER	read-write	This indicates the Explicit Forward Congestion Indication (EFCI) activation threshold in medium priority output buffer (OB); EFCI is generated towards the receiver termination point, in order to prevent congestion situation to be encountered within the output buffer; EFCI tagging is activated as soon as the activation threshold is reached; EFCI tagging is stopped as soon as the filling of the OB is below the EFCI desactivation threshold; the value range of the threshold is 0..adnHscBoardTrMgtMOBSize; this is not relevant for E1B and T1B boards.
INT adnHscBoardTrMgtEnvLOBEFCIOffTh	1.3.6.1.4.1.637.3.1.8.5.5.24.1.3	INTEGER	read-write	This indicates the Explicit Forward Congestion Indication (EFCI) desactivation threshold in low priority output buffer (OB); EFCI is generated towards the receiver termination point, in order to prevent congestion situation to be encountered within the output buffer; EFCI tagging is activated as soon as the activation threshold is reached; EFCI tagging is stopped as soon as the filling of the OB is below the EFCI desactivation threshold; the value range of the threshold is 0..adnHscBoardTrMgtLOBSize; this is not relevant for E1B and T1B boards.
adnAseBoardTrMgtEnvTable	1.3.6.1.4.1.637.3.1.8.5.5.25		not-accessible	This table is the BBASE Board Traffic Management environment table; the index is the AEI port number of the BBASE; this is relevant only for the matrix board with adnEquipSubType equal to adnBbaseb.
adnAseBoardTrMgtEnvEntry	1.3.6.1.4.1.637.3.1.8.5.5.25.1		not-accessible	An entry in the BBASE Board Traffic Management environment table.
INT adnAseBoardTrMgtEnvAeiPort	1.3.6.1.4.1.637.3.1.8.5.5.25.1.1	INTEGER	read-only	This is BBASE AEI port number.
INT adnAseBoardTrMgtEnvAeiSpeed	1.3.6.1.4.1.637.3.1.8.5.5.25.1.2	INTEGER	read-write	This indicates the speed of the AEI port ; the allowed values are : - speed622 : 622.08 Mb/s - speed603 : 603.23 Mb/s - speed593 : 593.80 Mb/s - speed565 : 565.53 Mb/s - speed155 : 155.52 Mb/s - speed150 : 150.81 Mb/s - speed148 : 148.45 Mb/s - speed142 : 142.00 Mb/s - speedLine : speed of the outgoing physical line ; this is relevant only for the matrix board with adnEquipSubType equal to adnBbaseb.
adnCongMgmtPrivateMIB	1.3.6.1.4.1.637.3.1.8.5.6
adnCongMgmtLTTable	1.3.6.1.4.1.637.3.1.8.5.6.1		not-accessible	The Frame Relay LT Information table for Congestion Management.
adnCongMgmtLTEntry	1.3.6.1.4.1.637.3.1.8.5.6.1.1		not-accessible	An entry in the Frame Relay LT Information table . The line and channel portion of ifIndex is not significant.
ADN adnCongMgmtLTTraceFlag	1.3.6.1.4.1.637.3.1.8.5.6.1.1.1	AdnEnableDisabled	read-write	flag indicating if trace per LT is enabled
OCT adnCongMgmtFreeBd2CongLevelTable	1.3.6.1.4.1.637.3.1.8.5.6.1.1.2	OCTET STRING	read-write	This is the BINARY table that determines the congestion level based upon the percentage of free Cryspix Buffer descriptors. It is placed here so that the level could be changed to achieve fine tuning. It is placed here for debugging and maintenance purpose only
INT adnCongMgmtProcUtilization	1.3.6.1.4.1.637.3.1.8.5.6.1.1.3	INTEGER	read-only	This is the processor utilization value of this LT as calculated by the congestion management. it is placed here for maintenance purpose only
adnCongMgmtChanEnvTable	1.3.6.1.4.1.637.3.1.8.5.6.2		not-accessible	The Frame Relay channel Information table for Congestion Management.
adnCongMgmtChanEnvEntry	1.3.6.1.4.1.637.3.1.8.5.6.2.1		not-accessible	An entry in the Frame Relay Channel Information table.
OCT adnCongMgmtChannel	1.3.6.1.4.1.637.3.1.8.5.6.2.1.1	OCTET STRING	read-only	This is the BINARY internal structure per channel maintained by congestion management. It contains the contents of the channel control block. It is placed here for maintenance purposes only.
OCT adnCongMgmtChanDiscMsgtrace	1.3.6.1.4.1.637.3.1.8.5.6.2.1.2	OCTET STRING	read-only	This is the BINARY discard message trace table per channel maintained by congestion management. It contents the discard message received by this channel from other cards. It is placed here for maintenance purposes only.
OCT adnCongMgmtChanAppliMsgTrace	1.3.6.1.4.1.637.3.1.8.5.6.2.1.3	OCTET STRING	read-only	This is the BINARY message trace table per channel maintained by congestion management. It contents the trace of all the messages received by this channel from the application. It is placed here for maintenance purposes only.
ADN adnCongMgmtChanTraceFlag	1.3.6.1.4.1.637.3.1.8.5.6.2.1.4	AdnEnableDisabled	read-write	flag indicating if trace per channel is enabled
INT adnCongMgmtChanUtilization	1.3.6.1.4.1.637.3.1.8.5.6.2.1.5	INTEGER	read-only	Current channel utilization value in the egress direction
INT adnCongMgmtChanEgressMaxCUF	1.3.6.1.4.1.637.3.1.8.5.6.2.1.6	INTEGER	read-write	This is the maximum of the egress channel utilization and the processor utilization. This field may be set to zero via SNMP command, so that the user may be able to measure or read the maximum CUF over a period of time.
INT adnCongMgmtChanMinTPSF	1.3.6.1.4.1.637.3.1.8.5.6.2.1.7	INTEGER	read-write	This is the minimum time in microseconds needed to process a subframe. This value is used when calculating processor utilization.
adnCongMgmtVCEnvTable	1.3.6.1.4.1.637.3.1.8.5.6.3		not-accessible	This is the VC table for Frame Relay Congestion Management.
adnCongMgmtVCEnvEntry	1.3.6.1.4.1.637.3.1.8.5.6.3.1		not-accessible	VC table entry
OCT adnCongMgmtVCcb	1.3.6.1.4.1.637.3.1.8.5.6.3.1.1	OCTET STRING	read-only	This is the BINARY internal PVC structure maintained by FRANP_SW. It is placed here for maintenance purposes only.
OCT adnCongMgmtVCLineDataTrace	1.3.6.1.4.1.637.3.1.8.5.6.3.1.2	OCTET STRING	read-only	This is an internal BINARY message trace table maintained by congestion management for this VC. This trace will contain relevant info for each subframe comming from the Line and going to the bus. It is placed here for maintenance purposes only.
OCT adnCongMgmtVCBusDataTrace	1.3.6.1.4.1.637.3.1.8.5.6.3.1.3	OCTET STRING	read-only	This is an internal BINARY message trace table maintained by congestion management for this VC. This trace will contain relevant info for each subframe comming from the Bus and going to the Line. It is placed here for maintenance purposes only.
ADN adnCongMgmtVCTraceEnable	1.3.6.1.4.1.637.3.1.8.5.6.3.1.4	AdnEnableDisabled	read-write	value indicating if trace per VC is enabled
OCT adnCongMgmtVCStateMachineTrace	1.3.6.1.4.1.637.3.1.8.5.6.3.1.5	OCTET STRING	read-only	This is an internal BINARY message trace table maintained by congestion management for this VC. This trace will contain the state and events of the SIR update state machine and ISM congestion state machine. It is placed here for maintenance purposes only.
adnCongMgmtLTTraceTable	1.3.6.1.4.1.637.3.1.8.5.6.4		not-accessible	The Frame Relay LT Trace table for Congestion Management.
adnCongMgmtLTTraceEntry	1.3.6.1.4.1.637.3.1.8.5.6.4.1		not-accessible	An entry in the Franp cm trace table
OCT adnCongMgmtLTCQtrace	1.3.6.1.4.1.637.3.1.8.5.6.4.1.1	OCTET STRING	read-only	This is the trace area for the calendar queue related variables. It is placed here for maintenance purpose only
INT adnCongMgmtTraceIndex	1.3.6.1.4.1.637.3.1.8.5.6.4.1.2	INTEGER	read-write	Index indicating the current index of Calendar Queue trace. This is used to display more than 255 bytes of trace by means of repeated getnext message from the INMP
adnLapPrivateMIB	1.3.6.1.4.1.637.3.1.8.5.7
adnLapPrivateTable	1.3.6.1.4.1.637.3.1.8.5.7.1		not-accessible	This is the LAP private table. It will exist once per LAP instance on each LT.
adnLapPrivateEntry	1.3.6.1.4.1.637.3.1.8.5.7.1.1		not-accessible	One instance of the adnLapPrivateTable. There will be one instance for each LAP on each LT.
INT adnLapPrivateTraceL1flag	1.3.6.1.4.1.637.3.1.8.5.7.1.1.1	INTEGER	read-write	This identifies the enable state of the tracing option at the Level 1 interface.
OCT adnLapPrivateTraceL1buffer	1.3.6.1.4.1.637.3.1.8.5.7.1.1.2	OCTET STRING	read-only	This is internal Level 1 message trace BINARY buffer
INT adnLapPrivateTraceL3flag	1.3.6.1.4.1.637.3.1.8.5.7.1.1.3	INTEGER	read-write	This identifies the enable state of the tracing option at the Level 3 interface.
OCT adnLapPrivateTraceL3buffer	1.3.6.1.4.1.637.3.1.8.5.7.1.1.4	OCTET STRING	read-only	This is internal Level 3 message trace BINARY buffer
INT adnLapPrivateTraceNMGSflag	1.3.6.1.4.1.637.3.1.8.5.7.1.1.5	INTEGER	read-write	This identifies the enable state of the tracing option at the NMGS interface.
OCT adnLapPrivateTraceNMGSbuffer	1.3.6.1.4.1.637.3.1.8.5.7.1.1.6	OCTET STRING	read-only	This is internal NMGSmessage trace BINARY buffer
INT adnLapFlowRASInfoflag	1.3.6.1.4.1.637.3.1.8.5.7.1.1.7	INTEGER	read-write	This identifies the enable state of the tracing option for RASinfo.
OCT adnLapFlowRASInfo	1.3.6.1.4.1.637.3.1.8.5.7.1.1.8	OCTET STRING	read-only	The statistics, trace information and current states debug dump fields to be used for remote debugging information. RAS = reliability, accessibility, serviceability
adnSsupEnvMIB	1.3.6.1.4.1.637.3.1.8.5.8
adnSsupCUDbgPCBTable	1.3.6.1.4.1.637.3.1.8.5.8.1		not-accessible	SSUPCU maintained SM processor control blocks. There is one such block for every secondary module (SM) processor that has been created (configured). The SSUPCU will keep current status information about the remote processor (among many other things) in such a block.
adnSsupCUDbgPCBEntry	1.3.6.1.4.1.637.3.1.8.5.8.1.1		not-accessible	This is a description of a single entry in the SSUPCU Processor control block table. For debugging reason, a hex-dump is considered sufficient for now. Structures defined in C-header files will be used to determine the values of the appropriate fields. The table exists only on the CU, and therefore uses the CENTRALIZED indexing for SFAS/MSUP routing purposes. The additional index will be encoded to 'adnProcessor' type definition allow SSUPCU code to determine which instance is desired by the user.
OCT adnSsupCUDbgPCBData	1.3.6.1.4.1.637.3.1.8.5.8.1.1.4	OCTET STRING	read-only	This is the hex-dump that represents the SSUPCU processor control block entry. Each such entry contains information about a SM processor on a coupler card that is configured.
adnSsupOMDbgPCBTable	1.3.6.1.4.1.637.3.1.8.5.8.2		not-accessible	SSUPOM maintained SM processor control blocks. There is one such block per OM processor. Only a single instance is maintained in each OM's memory, that pertaining to itself. This block contains information needed for the functioning of the processor, as well as information relating to the LT processors on the card.
adnSsupOMDbgPCBEntry	1.3.6.1.4.1.637.3.1.8.5.8.2.1		not-accessible	This is a description of a single entry in the SSUPOM Processor control block table. For debugging reason, a hex-dump is considered sufficient for now. Structures defined in C-header files will be used to determine the values of the appropriate fields. The 'adnCouplerIndex' is used for SFAS/MSUP routing purposes. This unfortunately only contains information of the chassis, slot and _line_ number (not processor). The user has to be aware of what line would map to the OM processor. Currently the line should be encoded as 512. Note that this information is likely to change.
ADN adnCouplerIndex	1.3.6.1.4.1.637.3.1.8.5.8.2.1.1	AdnCouplerIndex	read-only	The defintion of the 'adnCouplerIndex' object. It is used for routing the SNMP command to the appropriate processor by SFAS/MSUP sub-systems.
OCT adnSsupOMDbgPCBData	1.3.6.1.4.1.637.3.1.8.5.8.2.1.2	OCTET STRING	read-only	This is the hex-dump that represents the SSUPOM processor control block entry. Each such entry contains information about the OM processor in which memory the block resides.
adnSsupLTDbgPCBTable	1.3.6.1.4.1.637.3.1.8.5.8.3		not-accessible	SSUPLT maintained SM processor control blocks. There is one such block per LT processor. Only one block exists in each LT processor's memory, and it contains information needed by that processor only.
adnSsupLTDbgPCBEntry	1.3.6.1.4.1.637.3.1.8.5.8.3.1		not-accessible	This is a description of a single entry in the SSUPLT Processor control block table. For debugging reason, a hex-dump is considered sufficient for now. Structures defined in C-header files will be used to determine the values of the appropriate fields. The 'adnCouplerIndex' is used for SFAS/MSUP routing purposes. This unfortunately only contains information of the chassis, slot and _line_ number (not processor). The user has to be aware of what line would map to the LT processor. Currently the line should be encoded as 255 for the LLT, and 383 for the ULT processor. Note that this information is likely to change.
OCT adnSsupLTDbgPCBData	1.3.6.1.4.1.637.3.1.8.5.8.3.1.1	OCTET STRING	read-only	This is the hex-dump that represents the SSUPLT processor control block entry. Each such entry contains information about the LT processor in which memory the block resides.
adnAAFDEnvMIB	1.3.6.1.4.1.637.3.1.8.5.10
adnAAFDMaintTable	1.3.6.1.4.1.637.3.1.8.5.10.1		not-accessible	This table contains internal AAFD SWBB data structure, one entry per AAFD SWBB instance.
adnAAFDMaintEntry	1.3.6.1.4.1.637.3.1.8.5.10.1.1		not-accessible	An entry in the adnAAFDMaintTable. There will be one entry for each AAFD SWBB instance.
OCT adnAAFDContxt1	1.3.6.1.4.1.637.3.1.8.5.10.1.1.1	OCTET STRING	read-only	This is the first part of internal AAFD data structure containing internal error counters and structures.
OCT adnAAFDContxt2	1.3.6.1.4.1.637.3.1.8.5.10.1.1.2	OCTET STRING	read-only	This is the second part internal AAFD data structure containing internal error counters and structures.
OCT adnAAFDContxt3	1.3.6.1.4.1.637.3.1.8.5.10.1.1.3	OCTET STRING	read-only	This is the third part internal AAFD data structure containing internal error counters and structures.
OCT adnAAFDContxt4	1.3.6.1.4.1.637.3.1.8.5.10.1.1.4	OCTET STRING	read-only	This is the fourth part of internal AAFD data structure containing internal error counters and structures.
OCT adnAAFDContxt5	1.3.6.1.4.1.637.3.1.8.5.10.1.1.5	OCTET STRING	read-only	This is the fifth part internal AAFD data structure containing internal error counters and structures.
OCT adnAAFDContxt6	1.3.6.1.4.1.637.3.1.8.5.10.1.1.6	OCTET STRING	read-only	This is the sixth part internal AAFD data structure containing internal error counters and structures.
OCT adnAAFDContxt7	1.3.6.1.4.1.637.3.1.8.5.10.1.1.7	OCTET STRING	read-only	This is the seventh part internal AAFD data structure containing internal error counters and structures.
adnAAFDVCCMaintTable	1.3.6.1.4.1.637.3.1.8.5.10.2		not-accessible	This table contains internal AAFD SWBB data structure, one entry per Frame Relay logical line.
adnAAFDVCCMaintEntry	1.3.6.1.4.1.637.3.1.8.5.10.2.1		not-accessible	An entry in the adnAAFDVCCMaintTable. There will be one entry for each Frame Relay logical line.
OCT adnAAFDVCCContext1	1.3.6.1.4.1.637.3.1.8.5.10.2.1.1	OCTET STRING	read-only	This is the first part of internal data structure containing internal errors counters and structures concerning this Frame Relay logical line.
OCT adnAAFDVCCContext2	1.3.6.1.4.1.637.3.1.8.5.10.2.1.2	OCTET STRING	read-only	This is the second part of internal data structure containing internal errors counters and structures concerning this Frame Relay logical line.
OCT adnAAFDVCCContext3	1.3.6.1.4.1.637.3.1.8.5.10.2.1.3	OCTET STRING	read-only	This is the third part of internal data structure containing internal errors counters and structures concerning this Frame Relay logical line.
adnPssMIB	1.3.6.1.4.1.637.3.1.8.5.11
adnPssBWTable	1.3.6.1.4.1.637.3.1.8.5.11.1		not-accessible	Entry AdnPssBWEntry
adnPssBWEntry	1.3.6.1.4.1.637.3.1.8.5.11.1.1		not-accessible	Each entry (row) in the adnPSSBWTable. There will be one entry per ifindex
OCT adnPssAvailBW	1.3.6.1.4.1.637.3.1.8.5.11.1.1.1	OCTET STRING	read-only	This is the internal binary available bandwidth information received by Path Select for a particular ifindex.
INT adnpssifindex	1.3.6.1.4.1.637.3.1.8.5.11.1.1.2	INTEGER	read-only	This is adn pss ifindex.
adnPssTracehdrTable	1.3.6.1.4.1.637.3.1.8.5.11.2		not-accessible	This table contains various trace areas used by Path Select for maintenance/diagnostic purpose only.
adnPssTracehdrEntry	1.3.6.1.4.1.637.3.1.8.5.11.2.1		not-accessible	Each entry (row) in the adnPssTraceTable.
INT adnPssPrintFlag	1.3.6.1.4.1.637.3.1.8.5.11.2.1.1	INTEGER	read-write	This value is used to set Pss_print_flag to determine which printf's are allowed.
OCT adnPssFromFrtBuf	1.3.6.1.4.1.637.3.1.8.5.11.2.1.2	OCTET STRING	read-only	This is a binary value
OCT adnPssToFrtBuf	1.3.6.1.4.1.637.3.1.8.5.11.2.1.3	OCTET STRING	read-only	The binary buffer value
adnPssTraceTable	1.3.6.1.4.1.637.3.1.8.5.11.3		not-accessible	This table contains various trace areas used by Path Select for maintenance/diagnostic purpose only.
adnPssTraceEntry	1.3.6.1.4.1.637.3.1.8.5.11.3.1		not-accessible	Each entry (row) in the adnPssTraceTable.
INT adnPssTraceIndex	1.3.6.1.4.1.637.3.1.8.5.11.3.1.1	INTEGER	not-accessible	Trace Index Number
OCT adnPssTraceValue	1.3.6.1.4.1.637.3.1.8.5.11.3.1.2	OCTET STRING	read-only	This is the binary. All messages received from the Franp_si component are stored here
adnRtsagtMIB	1.3.6.1.4.1.637.3.1.8.5.12
adnRtsagtPrintFlagTable	1.3.6.1.4.1.637.3.1.8.5.12.1		not-accessible	This table is to turn on and off the print capability Routes Agent for maintenance/diagnostic purpose only.
adnRtsagtPrintFlagHdrEntry	1.3.6.1.4.1.637.3.1.8.5.12.1.1		not-accessible	Each entry (row) in the adnRtsagtPrintFlagTable.
INT adnRtsagtPrintFlag	1.3.6.1.4.1.637.3.1.8.5.12.1.1.1	INTEGER	read-write	This value is used to set Rtsagt_print_flag to determine which printf's are allowed.
adnRtsagtTraceTable	1.3.6.1.4.1.637.3.1.8.5.12.2		not-accessible	This table contains various trace areas used by Routes Agent for maintenance/diagnostic purpose only.
adnRtsagtTraceEntry	1.3.6.1.4.1.637.3.1.8.5.12.2.1		not-accessible	Each entry (row) in the adnRtsagtTraceTable.
INT adnRtsagtTraceIndex	1.3.6.1.4.1.637.3.1.8.5.12.2.1.1	INTEGER	not-accessible	Trace Index Number
OCT adnRtsagtTraceValue	1.3.6.1.4.1.637.3.1.8.5.12.2.1.2	OCTET STRING	read-only	This is the binary.
adnRtsagtLinkCtrlBlkTable	1.3.6.1.4.1.637.3.1.8.5.12.3		not-accessible	This table contains Link Control Block values
adnRtsagtLinkCtrlBlkEntry	1.3.6.1.4.1.637.3.1.8.5.12.3.1		not-accessible	Entry in the adnRtsagtLinkCtrlBlkTable.
INT adnRtsagtIfIndex	1.3.6.1.4.1.637.3.1.8.5.12.3.1.1	INTEGER	read-only	Routes agent link control block ifindex.
INT adnRtsagtLpx	1.3.6.1.4.1.637.3.1.8.5.12.3.1.2	INTEGER	read-only	Routes agent lpx self
INT adnRtsagtUserNetFlag	1.3.6.1.4.1.637.3.1.8.5.12.3.1.3	INTEGER	read-only	Routes Agent 0:user, 1 : network.
INT adnRtsagtHssTpx	1.3.6.1.4.1.637.3.1.8.5.12.3.1.4	INTEGER	read-only	Routes agent hss : 1, tpx : 0, other : 2.
INT adnRtsagtSigIfState	1.3.6.1.4.1.637.3.1.8.5.12.3.1.5	INTEGER	read-only	Routes agent Signal channel status received, sent, signal enabled, sig disabled, sig blocked, no. of sig states.
INT adnRtsagtL2IfState	1.3.6.1.4.1.637.3.1.8.5.12.3.1.6	INTEGER	read-only	Routes agent states for L2 Interface Idle or link released, Waiting for establish, Link Established, Awaiting release conf, L2 flow controlled us, Number of L2 states.
INT adnRtsagtMhIfState	1.3.6.1.4.1.637.3.1.8.5.12.3.1.7	INTEGER	read-only	Routes agent MH States, Add request sent to MH, MH link status down, Sent link up request, Link with MH is up, MH has sent XOFF, Local XOFF sent to MH, Number of MH states.
INT adnRtsagtL3IfState	1.3.6.1.4.1.637.3.1.8.5.12.3.1.8	INTEGER	read-only	Routes agent state of l3 interface, L3 not yet established, Sent Establish Req, We sent Xoff to Remote, Remote sent Xoff to us, We sent block to Remote, Remote sent block to us, Link up in data xfer, Number of L3 states.
INT adnRtsagtLhMainState	1.3.6.1.4.1.637.3.1.8.5.12.3.1.9	INTEGER	read-only	Routes agent state of Link Handler, Processing Add Request, Waiting for enable, Waiting for MDL confirm, Waiting TPX setup, Waiting TPX release, Waiting L2 establish, Waiting L3 establish, Wait for link up from MH, Wait for releases Link operational, L3 up, MH down on purpose, IACS is down, Number of LH states.
INT adnRtsagtSiCcb	1.3.6.1.4.1.637.3.1.8.5.12.3.1.10	INTEGER	read-only	Routes agent Pointer to control Block of signal.
INT adnRtsagtLtLpx	1.3.6.1.4.1.637.3.1.8.5.12.3.1.11	INTEGER	read-only	Routes agent lpx of lt.
INT adnRtsagtMemLpx	1.3.6.1.4.1.637.3.1.8.5.12.3.1.12	INTEGER	read-only	Routes agent lpx for lt data transfer memory
INT adnRtsagtAtmSiIfap	1.3.6.1.4.1.637.3.1.8.5.12.3.1.13	INTEGER	read-only	Routes agent Signalling IFAP
INT adnRtsagtAtmSiSuid	1.3.6.1.4.1.637.3.1.8.5.12.3.1.14	INTEGER	read-only	Routes agent SUID
INT adnRtsagtL3MaxPktSize	1.3.6.1.4.1.637.3.1.8.5.12.3.1.15	INTEGER	read-only	Routes agent negotiated pkt size with peer
INT adnRtsagtPeerVersion	1.3.6.1.4.1.637.3.1.8.5.12.3.1.16	INTEGER	read-only	Routes agent link handler version of peer
INT adnRtsagtHeartBeatTime	1.3.6.1.4.1.637.3.1.8.5.12.3.1.17	INTEGER	read-only	Routes agent time period of sending heartbeat
INT adnRtsagtLinkDeadTime	1.3.6.1.4.1.637.3.1.8.5.12.3.1.18	INTEGER	read-only	Routes agent if no heartbeat for this time
OCT adnRtsagtSigIfInfo	1.3.6.1.4.1.637.3.1.8.5.12.3.1.19	OCTET STRING	read-only	Routes agent information relevant to sig_if
OCT adnRtsagtL2IfInfo	1.3.6.1.4.1.637.3.1.8.5.12.3.1.20	OCTET STRING	read-only	Routes agent information relevant to l2_if
OCT adnRtsagtL3IfInfo	1.3.6.1.4.1.637.3.1.8.5.12.3.1.21	OCTET STRING	read-only	Routes agent information relevant to l3_if
OCT adnRtsagtMhIfInfo	1.3.6.1.4.1.637.3.1.8.5.12.3.1.22	OCTET STRING	read-only	Routes agent information relevant to mh_if
OCT adnRtsagtLhMainInfo	1.3.6.1.4.1.637.3.1.8.5.12.3.1.23	OCTET STRING	read-only	Routes agent information relevant to lh_main
OCT adnRtsagtLhTimerInfo	1.3.6.1.4.1.637.3.1.8.5.12.3.1.24	OCTET STRING	read-only	Routes agent timer info
INT adnRtsagtNextLcb	1.3.6.1.4.1.637.3.1.8.5.12.3.1.25	INTEGER	read-only	Routes agent next LCB in the list
INT adnRtsagtPrevLcb	1.3.6.1.4.1.637.3.1.8.5.12.3.1.26	INTEGER	read-only	Routes agent next LCB in the list
OCT adnRtsagtTimerDurations	1.3.6.1.4.1.637.3.1.8.5.12.3.1.27	OCTET STRING	read-only	Routes agent durations for various timers
INT adnRtsagtLayer2IdCcb	1.3.6.1.4.1.637.3.1.8.5.12.3.1.28	INTEGER	read-only	Routes agent set by layer2_id of Add channel
INT adnRtsagtLayer2RefCcb	1.3.6.1.4.1.637.3.1.8.5.12.3.1.29	INTEGER	read-only	Routes agent set by l2_ctx.l2_ref of mdl_assign_conf
INT adnRtsagtChannelType	1.3.6.1.4.1.637.3.1.8.5.12.3.1.30	INTEGER	read-only	Routes agent IfIndex type
OCT adnRtsagtLineMetric	1.3.6.1.4.1.637.3.1.8.5.12.3.1.31	OCTET STRING	read-only	Routes agent trace containing the delay and monetary cost metrics per line. The first and third octet strings are fields which contain a number representing the type of cost (delay(3) and monetary(4)). The second and fourth octet strings contain the actual cost value for the cost type defined in the field before it.
INT adnRtsagtLinkDeadFlag	1.3.6.1.4.1.637.3.1.8.5.12.3.1.32	INTEGER	read-only	Routes agent flag representing the status of the link dead timer on each line. A one indicates the timer is on and a zero indicates the timer is off. The link dead timer is a timer that starts when a line is set up and expires when there are no messages sent across the line for a period of time. If the timer expires the link is deemed dead and is reset. However, the timer is refreshed every time a message is sent across the link.
adnRtsagtLocalAddrTable	1.3.6.1.4.1.637.3.1.8.5.12.4		not-accessible	Entry in the adnRtsagtLocalAddrTable
adnRtsagtLocalAddrEntry	1.3.6.1.4.1.637.3.1.8.5.12.4.1		not-accessible	Entry in the adnRtsagtLocalAddrTable
INT adnRtsagtLocalAddrIndex	1.3.6.1.4.1.637.3.1.8.5.12.4.1.1	INTEGER	not-accessible	Routes agent Address Index.
OCT adnRtsagtLocalAddrBlkHdr	1.3.6.1.4.1.637.3.1.8.5.12.4.1.2	OCTET STRING	read-only	Routes Agent address entry block
OCT adnRtsagtLocalAddrBlkCard	1.3.6.1.4.1.637.3.1.8.5.12.4.1.3	OCTET STRING	read-only	Routes Agent address entry block
adnRtsagtTimerHdrTable	1.3.6.1.4.1.637.3.1.8.5.12.5		not-accessible	Entry in the adnRtsagtTimerHdrTable
adnRtsagtTimerHdrEntry	1.3.6.1.4.1.637.3.1.8.5.12.5.1		not-accessible	Entry in the adnRtsagtTimerHdrTable
INT adnRtsagtTimerIndex	1.3.6.1.4.1.637.3.1.8.5.12.5.1.1	INTEGER	read-only	Routes agent Timer Index.
INT adnRtsagtTimerDuration	1.3.6.1.4.1.637.3.1.8.5.12.5.1.2	INTEGER	read-only	Routes Agent Timer duration
INT adnRtsagtTimerPurpose	1.3.6.1.4.1.637.3.1.8.5.12.5.1.3	INTEGER	read-only	Routes Agent Timer Purpose
INT adnRtsagtTimerToBeDeleted	1.3.6.1.4.1.637.3.1.8.5.12.5.1.4	INTEGER	read-only	Routes Agent Timer tobedeleted
INT adnRtsagtTimerNext	1.3.6.1.4.1.637.3.1.8.5.12.5.1.5	INTEGER	read-only	Routes Agent Next timer pointer
INT adnRtsagtTimerPrevious	1.3.6.1.4.1.637.3.1.8.5.12.5.1.6	INTEGER	read-only	Routes Agent Next timer pointer
adnMsupToolBoxEnvMIB	1.3.6.1.4.1.637.3.1.8.5.13
INT adnMsupToolBoxSetup	1.3.6.1.4.1.637.3.1.8.5.13.1	INTEGER	read-write	This object provides a mechanism for controling the whole MSUP tool box setup. - default : the MSUP tool box configuration parameters are set to the default values. - temporary : the MSUP tool box configuration parameters have been personalized, but a CU restart will restore the default values. - permanent : the MSUP tool box configuration parameters have been personalized and saved in order to retrieve the personalization after CU cold or mild restarts. A set to permanent saves the setup for next restarts. A set to temporary keeps the current setup but deletes the previous save. A set to default restaures the default setup.
adnMsupCtxTable	1.3.6.1.4.1.637.3.1.8.5.13.2		not-accessible	A set of adnMsupCtxEntry entries.
adnMsupCtxEntry	1.3.6.1.4.1.637.3.1.8.5.13.2.1		not-accessible	This object provides a mechanism to dump on the CU craft interface contexts in MSUP memory.
ADN adnMsupCtxType	1.3.6.1.4.1.637.3.1.8.5.13.2.1.1	AdnMsupCtxType	read-only	The types of contexts in MSUP that can be dumped : - chassisCtx(1) : context of a chassis - boardCtx(2) : context of a board - processorCtx(3) : context of a processor - aeiPortCtx(4) : context of an AEI port - atmCtx(5) : ATM init context - generalCtx(6) : general MSUP data context - nodeConfigCtx(7) : node system configuration context - nodeSystCtx(8) : node system contextual context - sessionCtx(9) : IACS session context - cuCtx(10) : CU management context
INT adnMsupCtxIndex	1.3.6.1.4.1.637.3.1.8.5.13.2.1.2	INTEGER	read-only	The index of a context.
INT adnMsupCtxAction	1.3.6.1.4.1.637.3.1.8.5.13.2.1.3	INTEGER	read-write	This object provides a mechanism to print on the CU craft interface information about a context. - dump : dumps the content of a context, - address : displays the address of a context, - format : displays the context in a C format.
adnMsupPrintMIB	1.3.6.1.4.1.637.3.1.8.5.13.3
INT adnMsupPrintInterface	1.3.6.1.4.1.637.3.1.8.5.13.3.1	INTEGER	read-write	This object is a bitmap that enables to activate the printing of MSUP exchanges on the CU craft interface. bit val meaning --- ------------------------------------------------------- 1 displays exchanges with SMSUP 2 displays exchanges with ATMSUP 4 displays exchanges with APSUP 8 displays exchanges with CUSUP 16 displays exchanges with NMGS in fixed format 32 displays exchanges with FLS 64 displays exchanges with Debug Manager 128 displays traps sent to SFAS 256 displays localization service messages
INT adnMsupPrintExecution	1.3.6.1.4.1.637.3.1.8.5.13.3.2	INTEGER	read-write	This object is a bitmap that enables to activate the printing of MSUP exchanges on the CU craft interface. bit val meaning --- ------------------------------------------------------- 1 displays execution traces about coupler redundancy 2 displays execution traces about configuration 4 displays execution traces about clock synchronization 8 displays board automaton traces 16 displays processor automaton traces 32 displays execution traces about CU management 64 displays execution traces about coupler debug 128 displays execution traces about timer management
INT adnMsupPrintCouplerStr	1.3.6.1.4.1.637.3.1.8.5.13.3.3	INTEGER	read-write	This object enable to active the display of STR received through SMSUP or APSUP from couplers on the CU craft interface
adnMsupHssTraceMIB	1.3.6.1.4.1.637.3.1.8.5.13.4
INT adnMsupHssTraceLocalizationService	1.3.6.1.4.1.637.3.1.8.5.13.4.1	INTEGER	read-write	This object indicates wether the MSUP localization service writes into the MSUP HSS trace buffer.
INT adnMsupHssTracePrint	1.3.6.1.4.1.637.3.1.8.5.13.4.2	INTEGER	read-write	This object indicates wether MSUP prints the HSS traces on the CU craft interface in real time.
INT adnMsupHssTraceFreeze	1.3.6.1.4.1.637.3.1.8.5.13.4.3	INTEGER	read-write	This object indicates wether the MSUP HSS trace is frozen. On any CU restart this object is reset to the default value.
INT adnMsupHssTraceFreezeOnAnyStr	1.3.6.1.4.1.637.3.1.8.5.13.4.4	INTEGER	read-write	This object indicates wether the MSUP HSS trace is to be frozen on next MSUP STR.
INT adnMsupHssTraceFreezeOnStrNumber	1.3.6.1.4.1.637.3.1.8.5.13.4.5	INTEGER	read-write	Number of the STR on which to freeze the MSUP HSS trace. 0 is an unused STR number.
INT adnMsupHssTraceDump	1.3.6.1.4.1.637.3.1.8.5.13.4.6	INTEGER	read-write	This object provides a mechanism to dump on the CU craft interface the formated content of the whole MSUP HSS trace buffer.
INT adnMsupHssTraceSize	1.3.6.1.4.1.637.3.1.8.5.13.4.7	INTEGER	read-write	The size of the MSUP HSS trace buffer. A modification of this object can only be taken into account at the next start up.
adnCvsiHssEnvMIB	1.3.6.1.4.1.637.3.1.8.5.14
adnCvsiHssTable	1.3.6.1.4.1.637.3.1.8.5.14.1		not-accessible	This table is used by CVSI for the purpose of debugging.
adnCvsiHssEntry	1.3.6.1.4.1.637.3.1.8.5.14.1.1		not-accessible	An entry in the CVSI HSS Table.
INT adnCvsiHssIndex	1.3.6.1.4.1.637.3.1.8.5.14.1.1.1	INTEGER	read-only	This entry represents the current instance or index of the table. It is provided in order to be able to dump each instance of each object.
INT adnCvsiHssTraceCntl	1.3.6.1.4.1.637.3.1.8.5.14.1.1.2	INTEGER	read-write	This object provides a mechanism for controlling Cvsi's ability to enable/disable tracing of various types of messages. The following are the possible values it can hold. 0 - Trace disabled 1 - Trace CVSI Library information messages 2 - Trace CVSI Library Minor error messages 4 - Trace CVSI Library Major error messages 8 - Trace CVSI Library detailed messages 16 - Trace CVSI relay messages 32 - Trace CVSI Master messages 64 - Trace ATM Signalling messages 128 - Trace CLCS messages
OCT adnCvsiHssTraceArea	1.3.6.1.4.1.637.3.1.8.5.14.1.1.3	OCTET STRING	read-only	This is the internal BINARY message trace entry maintained by CVSI.
OCT adnCvsiHssCounters	1.3.6.1.4.1.637.3.1.8.5.14.1.1.4	OCTET STRING	read-only	This is the internal BINARY pointer to set of Counters maintained by CVSI.
OCT adnCvsiHssGlobalVars	1.3.6.1.4.1.637.3.1.8.5.14.1.1.5	OCTET STRING	read-only	CVSI global variables.
INT adnCvsiHssPrintCntl	1.3.6.1.4.1.637.3.1.8.5.14.1.1.6	INTEGER	read-write	This object provides a mechanism for controlling Cvsi's ability to print on the CU console various debugging information. The following are the possible values for this object. 0 - Print disabled 1 - Print CVSI Library information messages 2 - Print CVSI Library Minor error messages 4 - Print CVSI Library Major error messages 8 - Print CVSI Library detailed messages 16 - Print CVSI relay messages 32 - Print CVSI Master messages 64 - Print ATM Signalling messages 128 - Print CLCS messages
INT adnCvsiHssVcActive	1.3.6.1.4.1.637.3.1.8.5.14.1.1.7	INTEGER	read-only	Indicates the number of active TDP Virtual Circuits in the current node.
adnRtsmgrMIB	1.3.6.1.4.1.637.3.1.8.5.15
adnRtsmgrTraceTable	1.3.6.1.4.1.637.3.1.8.5.15.1		not-accessible	This table is used to get Message handling entries values for Route Manager.
adnRtsmgrTraceEntry	1.3.6.1.4.1.637.3.1.8.5.15.1.1		not-accessible	Each entry (row) in the adnRtsmgrTraceTable.
INT adnRtsmgrTraceIndex	1.3.6.1.4.1.637.3.1.8.5.15.1.1.1	INTEGER	not-accessible	Trace Index Number.
OCT adnRtsmgrTraceValue	1.3.6.1.4.1.637.3.1.8.5.15.1.1.2	OCTET STRING	read-only	This string displays a string of 36 bytes combination of Route Manager trace entry constants, trace entry variables, and time stamp.
adnIprtEnvMIB	1.3.6.1.4.1.637.3.1.8.5.16
adnIpRouteNetstatTable	1.3.6.1.4.1.637.3.1.8.5.16.1		not-accessible	This is the IP Routing Environmental Table
adnIpRouteNetstatEntry	1.3.6.1.4.1.637.3.1.8.5.16.1.1		not-accessible	The IP Route Int Entry provides access to the CU TCP/UDP/IP stack information. It is recommended that the objects of this table be fetched with an SNMP get/getnext/etc. of all instances of the given object without any index postfix.
INT adnIpRouteNetstatIndex	1.3.6.1.4.1.637.3.1.8.5.16.1.1.1	INTEGER	read-only	This object defines the Index into this table.
STR adnIpRouteNetstatIfconfig	1.3.6.1.4.1.637.3.1.8.5.16.1.1.2	DisplayString	read-only	This object defines the ASCII string that includes the CU IP Interface description (similar to unix [netstat -i] command).
STR adnIpRouteNetstatRoutes	1.3.6.1.4.1.637.3.1.8.5.16.1.1.3	DisplayString	read-only	This object defines the ASCII string that includes the CU IP Forwarding memory cache (similar to unix [netstat -r] command).
STR adnIpRouteNetstatProtStats	1.3.6.1.4.1.637.3.1.8.5.16.1.1.4	DisplayString	read-only	This object defines the ASCII string that includes the CU IP/ TCP/UPD packet count statistics (similar to unix [netstat -s] command).
STR adnIpRouteNetstatNetSockets	1.3.6.1.4.1.637.3.1.8.5.16.1.1.5	DisplayString	read-only	This object defines the ASCII string that includes the CU IP network sockets (similar to unix [netstat -a] command).
STR adnIpRouteNetstatNetConnec	1.3.6.1.4.1.637.3.1.8.5.16.1.1.6	DisplayString	read-only	This object defines the ASCII string that includes the CU IP network connections (similar to unix [netstat -A] command).
STR adnIpRouteNetstatNetNum	1.3.6.1.4.1.637.3.1.8.5.16.1.1.7	DisplayString	read-only	This object defines the ASCII string that includes the CU IP network numbers (similar to unix [netstat -n] command).
adnIpRouteDiagTable	1.3.6.1.4.1.637.3.1.8.5.16.2		not-accessible	This is the IP Routing Environmental Table
adnIpRouteDiagEntry	1.3.6.1.4.1.637.3.1.8.5.16.2.1		not-accessible	The IP Route Diag Entry defines IP Routing supplemental objects used to diagnose/trouble shoot IP Routing subsystem problems.
INT adnIpRouteDiagIndex	1.3.6.1.4.1.637.3.1.8.5.16.2.1.1	INTEGER	read-only	This object defines the Index into this table.
INT adnIpRouteDiagPrintFlags	1.3.6.1.4.1.637.3.1.8.5.16.2.1.2	INTEGER	read-write	This object defines the print control flags bit mask used to enable printing debugging messages to the CU console screen. Each bit position is used to enable printing of processing different level of internal IP Routing processing messages: -- The hexidecimal bit positions are defined as follows: 0x0001 Do not print any diagnostic messages 0x0002 Print only NHP messages 0x0004 Print only GAT messages 0x0008 Print only SNMP messages 0x0010 Print only CONFIG messages 0x0020 Print NMGS FSM messages 0x0040 Print SFAS FSM messages 0x0080 Print RDSS FSM messages 0x0100 Print GATED FSM messages 0x0200 Print all ERROR messages 0x0400 Print all DEBUG messages 0x0800 Print ALL the above message types 0x1000 Activate GateD with its trace ON --
adnRdssMIB	1.3.6.1.4.1.637.3.1.8.5.100
adnRdssRegistrationTable	1.3.6.1.4.1.637.3.1.8.5.100.1		not-accessible	This table contains an array of records to those subsystems that have established IACS session with Routes Distribution.
adnRdssRegistrationEntry	1.3.6.1.4.1.637.3.1.8.5.100.1.1		not-accessible	Entry in the adnRdssRegistrationTable.
INT adnRdssRegLpxIndex	1.3.6.1.4.1.637.3.1.8.5.100.1.1.1	INTEGER	read-only	The LPX of subsystem which is registered to Routes Distribution.
INT adnRdssIcsRef	1.3.6.1.4.1.637.3.1.8.5.100.1.1.2	INTEGER	read-only	ICS Reference number
INT adnRdssSessionId	1.3.6.1.4.1.637.3.1.8.5.100.1.1.3	INTEGER	read-only	This field identifies which SWBB (IPforwarding, ISNA, GDC, SFAS or PRTA) this registration entry is belong to.
INT adnRdssCongestionFlag	1.3.6.1.4.1.637.3.1.8.5.100.1.1.4	INTEGER	read-only	This flag indicates whether the IACS session between Routes Distribution and the registered subsystem (IPforwarding, ISNA, GDC, SFAS or PRTA) in registration entry is congested or not.
INT adnRdssFatSequenceNum	1.3.6.1.4.1.637.3.1.8.5.100.1.1.5	INTEGER	read-only	This field identifies the sequence number used to send the last previous FAT message. The sequence number increments sequentially on every new FAT message sent. It will be rolled back to zero when reached maximum value.
INT adnRdssGatSequenceNum	1.3.6.1.4.1.637.3.1.8.5.100.1.1.6	INTEGER	read-only	This field identifies the sequence number used to send the last previous GAT message. The sequence number increments sequentially on every new GAT message sent. It will be rolled back to zero when reached maximum value.
INT adnRdssMatSequenceNum	1.3.6.1.4.1.637.3.1.8.5.100.1.1.7	INTEGER	read-only	This field identifies the sequence number used to send the last previous MAT message. The sequence number increments sequentially on every new MAT message sent. It will be rolled back to zero when reached maximum value.
INT adnRdssAckFlags	1.3.6.1.4.1.637.3.1.8.5.100.1.1.8	INTEGER	read-only	This is bit-map field represents the statuses of acknowledgment from a previous transmitted FAT, GAT, or MAT message. Bit 0 represents FAT acknowledgment, bit 1 represents GAT acknowledgment, and bit 2 represents MAT acknowledgment. If a bit position has value of zero, it indicates the correspond acknowledgment message has not been received. When an acknowledgment message is received, its sequence number is compared with the correspond transmitted message's sequence number. If both are match, then the correspond Ack Flag bit will be set. If both are not match, then the received message will be ignored.
INT adnRdssNextHopLastSequenceNum	1.3.6.1.4.1.637.3.1.8.5.100.1.1.9	INTEGER	read-only	This field hold the sequesnce number of the last received valid Next-Hop message. It is used for handling duplicate received messages. This field is intialized to 0xff.
INT adnRdssLatLastSequenceNum	1.3.6.1.4.1.637.3.1.8.5.100.1.1.10	INTEGER	read-only	This field hold the sequesnce number of the last received valid LAT message. It is used for handling duplicate received messages. This field is intialized to 0xff.
INT adnRdssMatLastSequenceNum	1.3.6.1.4.1.637.3.1.8.5.100.1.1.11	INTEGER	read-only	This field hold the sequesnce number of the last received valid MAT message. It is used for handling duplicate received messages. This field is intialized to 0xff.
INT adnRdssTransmitMsgBufId	1.3.6.1.4.1.637.3.1.8.5.100.1.1.12	INTEGER	read-only	This is the address of the message buffer for sending data.
INT adnRdssGatTableTraverseStatus	1.3.6.1.4.1.637.3.1.8.5.100.1.1.13	INTEGER	read-only	This field is used to indentify whether the traversing is currently on LPX, Ifindex or VC.
INT adnRdssGatTableTraverseLpxKey	1.3.6.1.4.1.637.3.1.8.5.100.1.1.14	INTEGER	read-only	This field is used to identify the LPX of corresponding interface being traverse.
INT adnRdssTypeOfTableRequested	1.3.6.1.4.1.637.3.1.8.5.100.1.1.15	INTEGER	read-only	This field is bit-map defining what types of tables are to be provided to the registering subsystem. Table types include FAT, GAT, MAT, and etc.
INT adnRdssGatTableTraverseStartKey	1.3.6.1.4.1.637.3.1.8.5.100.1.1.16	INTEGER	read-only	This key is used for the purpose of distributing the entries from the GAT table when a SWBB subsystem has just register (just came up) with Routes Distribution. The Start Key is the key to the first entry sent on the previous message to aid in the scenario when retransmission of the previous message is required. Set Start key to NULL to indicate completed table has been sent, or table is empty. Set Start Key to KEY {Root} to start traversal. Set Start Key equal to End Key to indicate GAT table traversal is completed.
INT adnRdssGatTableTraverseEndKey	1.3.6.1.4.1.637.3.1.8.5.100.1.1.17	INTEGER	read-only	This key is used for the purpose of distributing the entries from the GAT table when a SWBB subsystem has just register (just came up) with Routes Distribution. The End Key is the key to the last GAT entry sent on the previous message, and is used to keep track of where in the GAT table to continue for the next message.
INT adnRdssGatMsgQueueStartPointer	1.3.6.1.4.1.637.3.1.8.5.100.1.1.18	INTEGER	read-only	The GAT message queue contains linked list of updated entries. This start pointer marks an entry in the lists as beginning entry in the lists to be sent or is sending to the correspond IP Forwarding subsystem.
INT adnRdssFatEntranceKey	1.3.6.1.4.1.637.3.1.8.5.100.1.1.19	INTEGER	read-only	The FAT Entrance Key. This field is used to set the starting point to traverse the FAT table for this session.
adnRdssForwardingTable	1.3.6.1.4.1.637.3.1.8.5.100.2		not-accessible	The forwarding table contains data information to be forwarded, and status and control information relating to the entry itself for table book keeping purpose.
adnRdssForwardingEntry	1.3.6.1.4.1.637.3.1.8.5.100.2.1		not-accessible	Entry in the adnRdssForwardingTable.
IP adnRdssDestIpAddress	1.3.6.1.4.1.637.3.1.8.5.100.2.1.1	IpAddress	read-only	The IP address of the destination prefix.
INT adnRdssFatMask	1.3.6.1.4.1.637.3.1.8.5.100.2.1.2	INTEGER	read-only	This field represent the valid number of leading bits in the prefix of this address. It is the network IP mask.
INT adnRdssFatFlag	1.3.6.1.4.1.637.3.1.8.5.100.2.1.3	INTEGER	read-only	This field represents the type of the destination IP address.
ADN adnRdssFatCommand	1.3.6.1.4.1.637.3.1.8.5.100.2.1.4	AdnRdssCommandType	read-only	This is the same as the command field in the entry message header. Except when the value od this field is 255, then it is for internal used.
INT adnRdssFatStatusAckCnt	1.3.6.1.4.1.637.3.1.8.5.100.2.1.5	INTEGER	read-only	This field conveys the status information of the entry itself. It has dual functions and divided into two separated fields: Entry Status field and ACK count field.
IP adnRdssNextHopIpAddr	1.3.6.1.4.1.637.3.1.8.5.100.2.1.6	IpAddress	read-only	This field represents the IP address of the directly connected router or the local IP address. If the adnRdssFatFlag is Local Host entry, then this field is Zero.
INT adnRdssFatLowerFsm	1.3.6.1.4.1.637.3.1.8.5.100.2.1.7	INTEGER	read-only	This longword is part of the three longwords which composes of forty eight 2-bit fields. Each 2-bits field represents the FSM of this entry to the corresponding IP Forwarding subsystem. The FAT Entry Processing FSM Control Block keeps track of which IP Forwarding this entry needed to be forwarding to, and which IP Forwarding this entry has been forwarded to, and which IP Forwarding has already acknowledged the reception of this entry.
INT adnRdssFatMidFsm	1.3.6.1.4.1.637.3.1.8.5.100.2.1.8	INTEGER	read-only	This longword is part of the three longwords which composes of forty eight 2-bit fields. Each 2-bits field represents the FSM of this entry to the corresponding IP Forwarding subsystem. The FAT Entry Processing FSM Control Block keeps track of which IP Forwarding this entry needed to be forwarding to, and which IP Forwarding this entry has been forwarded to, and which IP Forwarding has already acknowledged the reception of this entry.
INT adnRdssFatUpperFsm	1.3.6.1.4.1.637.3.1.8.5.100.2.1.9	INTEGER	read-only	This longword is part of the three longwords which composes of forty eight 2-bit fields. Each 2-bits field represents the FSM of this entry to the corresponding IP Forwarding subsystem. The FAT Entry Processing FSM Control Block keeps track of which IP Forwarding this entry needed to be forwarding to, and which IP Forwarding this entry has been forwarded to, and which IP Forwarding has already acknowledged the reception of this entry.
adnRdssGatIfindexTable	1.3.6.1.4.1.637.3.1.8.5.100.3		not-accessible	This table contains all information associated with all the ifindexes, which are configured in the IP Forwarding subsystems.
adnRdssGatIfindexEntry	1.3.6.1.4.1.637.3.1.8.5.100.3.1		not-accessible	Entry in the adnRdssGatIfindexTable.
INT adnRdssGatIfindexLpxIndex	1.3.6.1.4.1.637.3.1.8.5.100.3.1.1	INTEGER	read-only	The LPX of subsystem which is registered to Routes Distribution.
INT adnRdssGatIfIndex	1.3.6.1.4.1.637.3.1.8.5.100.3.1.2	INTEGER	read-only	This is the unique identifier associated to the logical IP interface.
ADN adnRdssGatIfindexOption	1.3.6.1.4.1.637.3.1.8.5.100.3.1.3	AdnRdssOption	read-only	Type of LAT message.
ADN adnRdssGatIfindexCommandType	1.3.6.1.4.1.637.3.1.8.5.100.3.1.4	AdnRdssCommandType	read-only	Type of LAT command.
ADN adnRdssGatIfindexStatus	1.3.6.1.4.1.637.3.1.8.5.100.3.1.5	AdnRdssStatus	read-only	Status of the ifindex.
IP adnRdssGatIfLiiAddress	1.3.6.1.4.1.637.3.1.8.5.100.3.1.6	IpAddress	read-only	This field is the source address associated with the ifindex.
INT adnRdssGatIfMask	1.3.6.1.4.1.637.3.1.8.5.100.3.1.7	INTEGER	read-only	This field represents the valid number of leading bits in the prefix of the adnRdssGatIfLiiAddress. It is the network IP mask.
INT adnRdssGatIfServiceType	1.3.6.1.4.1.637.3.1.8.5.100.3.1.8	INTEGER	read-only	This field defines the type of the data link layer below the . Refer to RFC 1512 for the exhaustive list of the service types. We currently support only Frame Relay and AAL5/ATM.
INT adnRdssGatIfMtu	1.3.6.1.4.1.637.3.1.8.5.100.3.1.9	INTEGER	read-only	This field represents the size of the MTU associated with this ifindex.
INT adnRdssGatIfPrivateData	1.3.6.1.4.1.637.3.1.8.5.100.3.1.11	INTEGER	read-only	This field is used by IPFW and is passed as it is from RDSS to all other IP Forwarding subsystems.
IP adnRdssGatIfBroadcastAddr	1.3.6.1.4.1.637.3.1.8.5.100.3.1.12	IpAddress	read-only	This field represents the broadcast IP address associated with the Ifindex.
INT adnRdssGatIfCost	1.3.6.1.4.1.637.3.1.8.5.100.3.1.13	INTEGER	read-only	This is the interface cost associated with the ifindex.
adnRdssGatVcTable	1.3.6.1.4.1.637.3.1.8.5.100.4		not-accessible	This table contains all information associated with all the VCs, which are configured in the IP Forwarding subsystems.
adnRdssGatVcEntry	1.3.6.1.4.1.637.3.1.8.5.100.4.1		not-accessible	Entry in the adnRdssGatVcTable.
IP adnRdssGatVcNextHopAddr	1.3.6.1.4.1.637.3.1.8.5.100.4.1.1	IpAddress	read-only	This field represents the IP address of the directly connected router or the local IP address.
INT adnRdssGatVcLpx	1.3.6.1.4.1.637.3.1.8.5.100.4.1.2	INTEGER	read-only	The LPX of subsystem which is registered to Routes Distribution.
INT adnRdssGatVcIfIndex	1.3.6.1.4.1.637.3.1.8.5.100.4.1.3	INTEGER	read-only	This is the unique identifier associated to the VC.
INT adnRdssGatVcVpiVciOrDlci	1.3.6.1.4.1.637.3.1.8.5.100.4.1.4	INTEGER	read-only	This field represents the data link identifier (VPI/VCI for AAL5 or DLCI for Frame Relay for the Next-Hop under discussion.
ADN adnRdssGatVcOption	1.3.6.1.4.1.637.3.1.8.5.100.4.1.5	AdnRdssOption	read-only	Type of LAT message.
ADN adnRdssGatVcCommandType	1.3.6.1.4.1.637.3.1.8.5.100.4.1.6	AdnRdssCommandType	read-only	Type of LAT Vc command.
ADN adnRdssGatVcStatus	1.3.6.1.4.1.637.3.1.8.5.100.4.1.7	AdnRdssStatus	read-only	Status of Vc.
INT adnRdssGatVcServiceType	1.3.6.1.4.1.637.3.1.8.5.100.4.1.8	INTEGER	read-only	This field defines the type of the data link layer below the . Refer to RFC 1512 for the exhaustive list of the service types. We currently support only Frame Relay and AAL5/ATM.
INT adnRdssGatVcCost	1.3.6.1.4.1.637.3.1.8.5.100.4.1.9	INTEGER	read-only	This is the interface cost associated with the ifindex.
IP adnRdssGatVcLiiAddress	1.3.6.1.4.1.637.3.1.8.5.100.4.1.10	IpAddress	read-only	This field is the source address associated with the ifindex.
adnRdssTraceTable	1.3.6.1.4.1.637.3.1.8.5.100.5		not-accessible	Each entry (row) in the adnRdssTraceTable
adnRdssTraceEntry	1.3.6.1.4.1.637.3.1.8.5.100.5.1		not-accessible	Each entry (row) in the adnRtsagtTraceTable.
INT adnRdssTraceLpxIndex	1.3.6.1.4.1.637.3.1.8.5.100.5.1.1	INTEGER	not-accessible	LPX of registered subsystems.
INT adnRdssTraceIndex	1.3.6.1.4.1.637.3.1.8.5.100.5.1.2	INTEGER	not-accessible	Trace Index Number
OCT adnRdssTraceValue	1.3.6.1.4.1.637.3.1.8.5.100.5.1.3	OCTET STRING	read-only	This is the binary.
adnEnvMIB	1.3.6.1.4.1.637.3.2

RFC description

Provides environmental and debugging information for Alcatel Data Networks frame relay and ATM equipment.

Start monitoring Frame Relay access equipment (FRANP signalling) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ADN-ENV-MIB

What Is ADN-ENV-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description