CISCO-WAN-SVC-MIB

All MIBs › CISCO-WAN-SVC-MIB

Organization: Cisco System, Inc

Last Updated: 2003-03-10

Category: ATM, Vendor: Cisco Devices

Description: Manages Cisco WAN Switched Virtual Circuit (SVC) configuration and call control on ATM platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-WAN-SVC-MIB?

CISCO-WAN-SVC-MIB is a vendor-specific MIB for Cisco's BPX-SES and MGX ATM WAN switching platforms, describing ATM network services including Switched Virtual Circuit (SVC) call control, provisioning, and status gathering, using ATM/PNNI terminology such as ABR, AINI, and ENNI. It exposes configuration data (software revision, controller status) and connection-oriented protocol state, notably SSCOP (Service Specific Connection Oriented Protocol) timer and status tables used in signaling between ATM switches. Its monitoring value spans both hardware/software status (controller and standby-controller operational state, software revision) and protocol-layer health (SSCOP connection timers governing PNNI/AINI signaling links), letting an operator confirm that ATM signaling adjacencies between switches remain stable and that redundant controllers are correctly synchronized. It is closely tied to standard ATM and PNNI signaling concepts and to Cisco's broader WAN switching MIB family for the BPX-SES/MGX product lines. It is deployed on Cisco BPX-SES and MGX ATM switches in carrier/enterprise ATM backbone networks providing SVC-based connectivity. Network engineers evaluating or troubleshooting this functionality can download the CISCO-WAN-SVC-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-WAN-SVC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco BPX-SES ATM switch
Cisco MGX ATM switch

Monitoring Examples

An administrator would check cwsControllerStatus and cwspPnniStndbyControllerStatus / cwspPnniControllerStatus (with cwspPnniControllerPhySlot identifying the physical slot) to confirm the active and standby PNNI controllers are both healthy and correctly synchronized. Polling cwspSscopTable / cwspSscopEntry for timer values like cwspSscopTmrKeepAlive, cwspSscopTmrNoResp, and cwspSscopTmrPoll would reveal whether an SSCOP signaling link to a neighboring switch is stable or repeatedly timing out, which would indicate an ATM inter-switch signaling adjacency problem affecting SVC call setup. cwsSwRevision lets the operator confirm the running software version matches the expected baseline across redundant controllers.

What Can Be Monitored

active/standby ATM controller status
software revision
SSCOP signaling timers
PNNI controller physical slot status
SVC call/service configuration

Imported Objects

From ATM-FORUM-TC-MIB

AtmAddress
NetPrefix

From CISCO-WAN-ATM-CONN-MIB

CiscoWanNsapAtmAddress

From CISCOWAN-SMI

stratacom

MODULE-IDENTITY

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From PNNI-MIB

PnniNodeId
PnniPortId

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using cwspSscopIgnoredPduRcv OID:

Select a Cisco BPX-SES/MGX ATM switch (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cwspSscopIgnoredPduRcv into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object stores the number of SSCOP PDUs that are received but ignored due to incorrect size, invalid PDU, unknown PDU type. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT ciscoWANPnniLinkStatus	1.3.6.1.4.1.351.140.1.3.1	INTEGER	read-only	Indicates the status of a link has changed: 1 - the link entered the 2-Way Inside state, 2 - the link exit the 2-Way Inside state, 3 - the link entered the 2-Way Outside state, 4 - the link exit the 2-Way Outside state. 5 - the link entered the Common Outside state, or 6 - the link exit the Common Outside state and entered the 1-Way Outside state.
INT ciscoWANPnniPglStatus	1.3.6.1.4.1.351.140.1.3.2	INTEGER	read-only	Indicates the status of PGL process has changed: 1 - the PGL exit the hung-election state, or 2 - the PGL entered the hung-election state.
PNN ciscoWANPnniPortId	1.3.6.1.4.1.351.140.1.3.5	PnniPortId	read-only	The port identifier of the port.
INT ciscoWANPnniReachability	1.3.6.1.4.1.351.140.1.3.3	INTEGER	read-only	This object is used in conjunction with ciscoWANPnniRemoteNodeId to indicate the reachability of the RemoteNode has changed: 1 - RemoteNode became reachable, or 2 - RemoteNode became unreachable.
PNN ciscoWANPnniRemoteNodeId	1.3.6.1.4.1.351.140.1.3.4	PnniNodeId	read-only	Indicates the node identifier of a remote node. If the remote node ID is unknown, this attribute is set to all zeros.
ciscoWANPnniRouting	1.3.6.1.4.1.351.140.1.3
ciscoWANSpvc	1.3.6.1.4.1.351.140.1.4
CWS ciscoWANSpvcFailReason	1.3.6.1.4.1.351.140.1.4.1	CwspSpvcState	read-only	Defines SPVC manager failures. Refer description in the textual convention. Note: this object is for Supporting Varbinds used only in trap definitions. The NMS applications should not depend on the implementation of this object. The SNMP Requests(GET,GET-NEXT) is not valid for this object.
ciscoWANSvcInfo	1.3.6.1.4.1.351.140.1.1
ciscoWANSvcMIB	1.3.6.1.4.1.351.140			The MIB modules describe an ATM network service on a BPX-SES or a MGX ATM switch. This MIB module provides configuring, provisioning, as well as status gathering for ATM services. Abbreviation used: ABR -- Available Bit Rate AINI -- ATM Inter-Network Interface ATM -- Asynchronous Transfer Mode BGN -- Begin BW -- Bandwidth CBR -- Constant Bit Rate ENNI -- Enhanced Network to Network Interface Note: The 'ENNI' term used here indicating 'enhanced' or 'friendly' NNI for linking two networks of CISCO AutoRoute or PNNI switches. The XPVCs and XPVPs are provisioned across them. Functionality includes changing segment OAM cell handling so that these cells flow over 'end-to-end OAM segment' loops for the provisioned length of the XPVC or XPVP, i.e. the 'segment' comprises the two or three segments between the user ports. Also implemented at ENNIs is an LMI functionality that enables auto-discovery of the ENNIs. ER -- Error Recovery GAT -- Generic Application Transport IE -- Information Element IISP -- Interim Inter-Switch Signaling Protocol ILMI -- Interim Local Management Interface MD -- Management Data PNNI -- Private Network-Network Interface RS -- Resynchronization REJ -- Rejection SD -- Sequence Data SDP -- Sequence Data with Poll SPVC -- Soft Permanent Virtual Circuit SSCOP -- Service Specific Connection Oriented Protocol SVC -- Switched Virtual Circuit UBR -- Unspecified Bit Rate UD -- Unit Data UNI -- User-Network Interface USTAT -- Unsolicited STAT VBR -- Variable Bit Rate
ciscoWANSvcMIBCompliance	1.3.6.1.4.1.351.140.3.1.1			The compliance statement for entities that support the Cisco SVC MIB.
ciscoWANSvcMIBCompliance2	1.3.6.1.4.1.351.140.3.1.2			The compliance statement for entities that support the Cisco SVC MIB.
ciscoWANSvcMIBCompliance3	1.3.6.1.4.1.351.140.3.1.3			The compliance statement for entities that support the Cisco SVC MIB.
ciscoWANSvcMIBCompliances	1.3.6.1.4.1.351.140.3.1
ciscoWANSvcMIBConformance	1.3.6.1.4.1.351.140.3
ciscoWANSvcMIBGroups	1.3.6.1.4.1.351.140.3.2
ciscoWANSvcMIBObjects	1.3.6.1.4.1.351.140.1
ciscoWANSvcPort	1.3.6.1.4.1.351.140.1.2
CWS cwsControllerStatus	1.3.6.1.4.1.351.140.1.1.6	CwspControllerState	read-only	The administrative status for the pnni active controller.
cwsInfoGrp	1.3.6.1.4.1.351.140.3.2.1			A collection of objects providing device level information.
cwspAbrCall	1.3.6.1.4.1.351.140.1.2.9
INT cwspAbrCallBearerClass	1.3.6.1.4.1.351.140.1.2.9.1.1.14	INTEGER	read-only	The Bearer Class of the ABR call. It could be BCOB-A, BCOB-C, BCOB-X or VP Service.
I32 cwspAbrCallBwdAdtf	1.3.6.1.4.1.351.140.1.2.9.1.1.38	Integer32	read-only	The Allowed Cell Rate (ACR) Decrease Time Factor for the ABR call in the backward direction. This is the time permitted between sending RM-cells before the rate is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 msecs. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds).
INT cwspAbrCallBwdCdf	1.3.6.1.4.1.351.140.1.2.9.1.1.39	INTEGER	read-only	The Cutoff Decrease Factor for the ABR call in the backward direction. This controls the decrease in Allowed Cell Rate (ACR) associated with missing RM-cell count (CRM). Larger values result in faster rate decrease. The default value is cdfOneOver16(4).
INT cwspAbrCallBwdFrameDiscard	1.3.6.1.4.1.351.140.1.2.9.1.1.40	INTEGER	read-only	Whether Frame Discard is enabled or disabled in the backward direction for the ABR call.
I32 cwspAbrCallBwdIcr	1.3.6.1.4.1.351.140.1.2.9.1.1.32	Integer32	read-only	The Initial Cell Rate for the ABR call in the backward direction. This is the rate at which the source starts, both initially and after an idle period. The value must not be larger than PCR, and is usually lower.
I32 cwspAbrCallBwdMcr	1.3.6.1.4.1.351.140.1.2.9.1.1.31	Integer32	read-only	The Minimum Cell Rate for the ABR call in the backward direction.
INT cwspAbrCallBwdNrm	1.3.6.1.4.1.351.140.1.2.9.1.1.36	INTEGER	read-only	The Maximum Number of Cells a source may send for each forward RM-cell in the backward direction for the ABR call. The default value is nrm32(5).
I32 cwspAbrCallBwdPcr	1.3.6.1.4.1.351.140.1.2.9.1.1.30	Integer32	read-only	The Peak Cell Rate for the ABR call in the backward direction.
INT cwspAbrCallBwdRdf	1.3.6.1.4.1.351.140.1.2.9.1.1.34	INTEGER	read-only	The Rate Decrease Factor for the ABR call in the backward direction. This controls the rate decrease which occurs when forward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12).
INT cwspAbrCallBwdRif	1.3.6.1.4.1.351.140.1.2.9.1.1.33	INTEGER	read-only	The Rate Increase Factor for the ABR call in the backward direction. This controls the rate at which the rate increases, when a forward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12).
I32 cwspAbrCallBwdTbe	1.3.6.1.4.1.351.140.1.2.9.1.1.35	Integer32	read-only	The Transient Buffer Exposure for the ABR call in the backward direction. This is the negotiated number of cells that the network would like to limit the source to sending during setup periods, before the first RM-cell returns.
INT cwspAbrCallBwdTrm	1.3.6.1.4.1.351.140.1.2.9.1.1.37	INTEGER	read-only	The Upper Bound on the time between forward RM-cells in the backward direction for the ABR call.
I32 cwspAbrCallCallRef	1.3.6.1.4.1.351.140.1.2.9.1.1.3	Integer32	read-only	The Call Reference value of the ABR call on this interface.
INT cwspAbrCallCastType	1.3.6.1.4.1.351.140.1.2.9.1.1.16	INTEGER	read-only	The Cast Type of the ABR call, which can only be Point-to-Point(p2p) call.
ADR cwspAbrCallCldAddress	1.3.6.1.4.1.351.140.1.2.9.1.1.5	AtmAddress	read-only	The Called Party Address of the ABR call.
ADR cwspAbrCallCldSubAddr	1.3.6.1.4.1.351.140.1.2.9.1.1.7	AtmAddress	read-only	The Called Party Subaddress of the ABR call.
ADR cwspAbrCallClgAddress	1.3.6.1.4.1.351.140.1.2.9.1.1.4	AtmAddress	read-only	The Calling Party Address of the ABR call.
ADR cwspAbrCallClgSubAddr	1.3.6.1.4.1.351.140.1.2.9.1.1.6	AtmAddress	read-only	The Calling Party Subaddress of the ABR call.
INT cwspAbrCallClipSusceptibility	1.3.6.1.4.1.351.140.1.2.9.1.1.17	INTEGER	read-only	Susceptibility to Clipping. It can be susceptible or not susceptible.
cwspAbrCallEntry	1.3.6.1.4.1.351.140.1.2.9.1.1		not-accessible	An entry in the table, containing information about an ABR call.
I32 cwspAbrCallFrtt	1.3.6.1.4.1.351.140.1.2.9.1.1.41	Integer32	read-only	The Fixed Round-Trip Time for the ABR call. This is the sum of the fixed and propagation delays from the source to the furthest destination and back.
I32 cwspAbrCallFwdAdtf	1.3.6.1.4.1.351.140.1.2.9.1.1.27	Integer32	read-only	The Allowed Cell Rate (ACR) Decrease Time Factor for the ABR call in the forward direction. This is the time permitted between sending RM-cells before the rate is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 msecs. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds).
INT cwspAbrCallFwdCdf	1.3.6.1.4.1.351.140.1.2.9.1.1.28	INTEGER	read-only	The Cutoff Decrease Factor for the ABR call in the forward direction. This controls the decrease in Allowed Cell Rate (ACR) associated with missing RM-cell count (CRM). Larger values result in faster rate decrease. The default value is cdfOneOver16(4).
INT cwspAbrCallFwdConformance	1.3.6.1.4.1.351.140.1.2.9.1.1.18	INTEGER	read-only	The Conformance of the ABR call to the traffic sets in the forward direction. It can only be ABR as defined in ATMF Traffic Management 4.0 specification.
INT cwspAbrCallFwdFrameDiscard	1.3.6.1.4.1.351.140.1.2.9.1.1.29	INTEGER	read-only	Whether Frame Discard is enabled or disabled in the forward direction for the ABR call.
I32 cwspAbrCallFwdIcr	1.3.6.1.4.1.351.140.1.2.9.1.1.21	Integer32	read-only	The Initial Cell Rate for the ABR call in the forward direction. This is the rate at which the source starts, both initially and after an idle period. The value must not be larger than PCR, and is usually lower.
I32 cwspAbrCallFwdMcr	1.3.6.1.4.1.351.140.1.2.9.1.1.20	Integer32	read-only	The Minimum Cell Rate for the ABR call in the forward direction.
INT cwspAbrCallFwdNrm	1.3.6.1.4.1.351.140.1.2.9.1.1.25	INTEGER	read-only	The Maximum Number of Cells a source may send for each forward RM-cell in the forward direction for the ABR call. The default value is nrm32(5).
I32 cwspAbrCallFwdPcr	1.3.6.1.4.1.351.140.1.2.9.1.1.19	Integer32	read-only	The Peak Cell Rate for the ABR call in the forward direction.
INT cwspAbrCallFwdRdf	1.3.6.1.4.1.351.140.1.2.9.1.1.23	INTEGER	read-only	The Rate Decrease Factor for the ABR call in the forward direction. This controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12).
INT cwspAbrCallFwdRif	1.3.6.1.4.1.351.140.1.2.9.1.1.22	INTEGER	read-only	The Rate Increase Factor for the ABR call in the forward direction. This controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12).
I32 cwspAbrCallFwdTbe	1.3.6.1.4.1.351.140.1.2.9.1.1.24	Integer32	read-only	The Transient Buffer Exposure for the ABR call in the forward direction. This is the negotiated number of cells that the network would like to limit the source to sending during setup periods, before the first RM-cell returns.
INT cwspAbrCallFwdTrm	1.3.6.1.4.1.351.140.1.2.9.1.1.26	INTEGER	read-only	The Upper Bound on the time between forward RM-cells in the forward direction for the ABR call.
cwspAbrCallGrp	1.3.6.1.4.1.351.140.3.2.7			A collection of objects providing information about ABR calls and associated parameters of a interface.
I32 cwspAbrCallMaxBwdCdv	1.3.6.1.4.1.351.140.1.2.9.1.1.45	Integer32	read-only	The Maximum Cell Delay Variation in the backward direction for the ABR call on this interface.
I32 cwspAbrCallMaxBwdClr	1.3.6.1.4.1.351.140.1.2.9.1.1.46	Integer32	read-only	The Maximum Cell Loss Ratio in the backward direction for the ABR call on this interface.
I32 cwspAbrCallMaxCtd	1.3.6.1.4.1.351.140.1.2.9.1.1.42	Integer32	read-only	The Maximum Cell Transfer Delay for the ABR call on this interface.
I32 cwspAbrCallMaxFwdCdv	1.3.6.1.4.1.351.140.1.2.9.1.1.43	Integer32	read-only	The Maximum Cell Delay Variation in the forward direction for the ABR call on this interface.
I32 cwspAbrCallMaxFwdClr	1.3.6.1.4.1.351.140.1.2.9.1.1.44	Integer32	read-only	The Maximum Cell Loss Ratio in the forward direction for the ABR call on this interface.
I32 cwspAbrCallOtherIntfCallRef	1.3.6.1.4.1.351.140.1.2.9.1.1.11	Integer32	read-only	The Call Reference of the ABR call on the partner interface.
I32 cwspAbrCallOtherIntfIndex	1.3.6.1.4.1.351.140.1.2.9.1.1.8	Integer32	read-only	The Other Interface ID of the ABR call. Generally this would be the outgoing/egress interface for the call.
I32 cwspAbrCallOtherIntfVci	1.3.6.1.4.1.351.140.1.2.9.1.1.10	Integer32	read-only	The VCI value of the ABR call on the partner interface. The value should be in the range of 32-65535 (0=SPVP).
I32 cwspAbrCallOtherIntfVpi	1.3.6.1.4.1.351.140.1.2.9.1.1.9	Integer32	read-only	The VPI value of the ABR call on the partner interface.
INT cwspAbrCallServiceCategory	1.3.6.1.4.1.351.140.1.2.9.1.1.15	INTEGER	read-only	The Service Category of the ABR call, which is ABR.
TIM cwspAbrCallStartTime	1.3.6.1.4.1.351.140.1.2.9.1.1.13	TimeStamp	read-only	The start time of the ABR call. This is the timestamp when the Setup Message (or Add Party Message) was first received on this interface.
cwspAbrCallTable	1.3.6.1.4.1.351.140.1.2.9.1		not-accessible	This table contains information for ABR calls on an interface.
INT cwspAbrCallType	1.3.6.1.4.1.351.140.1.2.9.1.1.12	INTEGER	read-only	The Call Type for the ABR call on this interface. The call type could be SVC or SPVC.
I32 cwspAbrCallVci	1.3.6.1.4.1.351.140.1.2.9.1.1.2	Integer32	not-accessible	The VCI value of the ABR call on this interface. The value should be in the range of 32-65535 (0=SPVP).
I32 cwspAbrCallVpi	1.3.6.1.4.1.351.140.1.2.9.1.1.1	Integer32	not-accessible	The VPI value of the ABR call on this interface.
C32 cwspAddPtyAckRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.16	Counter32	read-only	Number of ADD PARTY ACK messages received on this interface.
C32 cwspAddPtyAckXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.38	Counter32	read-only	Number of ADD PARTY ACK messages transmitted from this interface.
C32 cwspAddPtyRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.15	Counter32	read-only	Number of ADD PARTY messages received on this interface.
C32 cwspAddPtyRejRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.17	Counter32	read-only	Number of ADD PARTY REJECT messages received on this interface.
C32 cwspAddPtyRejXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.39	Counter32	read-only	Number of ADD PARTY REJECT messages transmitted from this interface.
C32 cwspAddPtyXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.37	Counter32	read-only	Number of ADD PARTY messages transmitted from this interface.
cwspAddress	1.3.6.1.4.1.351.140.1.2.11
cwspAddressEntry	1.3.6.1.4.1.351.140.1.2.11.1.1		not-accessible	An entry in the table, containing information about a reachable address.
cwspAddressGrp	1.3.6.1.4.1.351.140.3.2.10			A collection of objects providing information about ATM End System Addresses.
ROW cwspAddressRowStatus	1.3.6.1.4.1.351.140.1.2.11.1.1.8	RowStatus	read-create	To create or delete a reachable address. Note that NMS should use CreateAndGo to create a row and Destroy to delete a row. The managed device will return active or notInService as row status.
cwspAddressTable	1.3.6.1.4.1.351.140.1.2.11.1		not-accessible	The Interface ATM Address Table. This table contains all the attributes necessary to determine what the PNNI entity believes is reachable in terms of ATM End System Addresses and to determine which nodes are advertising this reachability. This table is also used to configure static routes to reachable addresses. Entries in this table can be created/deleted by setting the intfAddressRowStatus object to appropriate values. Existing entries in this table cannot be modified. Entries in this table can also be created/deleted through the command provided by the CLI.
INT cwspAddrLen	1.3.6.1.4.1.351.140.1.2.11.1.1.2	INTEGER	not-accessible	The address length in bits to be applied to the ATM End System Address.
INT cwspAddrPlan	1.3.6.1.4.1.351.140.1.2.11.1.1.5	INTEGER	read-create	The address plan. For NSAP address, the first byte of the address automatically implies one of the three NSAP address plans: NSAP E.164, NSAP DCC or NSAP ICD.
INT cwspAddrPlanSupported	1.3.6.1.4.1.351.140.1.2.1.1.1.30	INTEGER	read-create	The ATM address plan supported on an interface. This can only be modified if interface is public UNI. For all other interfaces, the value is aesa.
INT cwspAddrProto	1.3.6.1.4.1.351.140.1.2.11.1.1.4	INTEGER	read-create	The routing mechanism via which the connectivity from the advertising node to the reachable address was learned. A 'local' address indicates this address is automatically advertised. A 'static' address is not automatically advertised. By setting 'cwspAddrRedistribute' variable (see below) to 'true' will force a 'static' address to be advertised.
T/F cwspAddrRedistribute	1.3.6.1.4.1.351.140.1.2.11.1.1.7	TruthValue	read-create	Whether or not the reachable address specified by this entry is to be advertised by the local node into its PNNI routing domain. This object is only meaningful if the routing mechanism (cwspAddrProto) is static.
INT cwspAddrScope	1.3.6.1.4.1.351.140.1.2.11.1.1.6	INTEGER	read-create	The PNNI scope of advertisement (i.e. level of PNNI hierarchy) of the reachability from the advertising node to the address.
INT cwspAddrType	1.3.6.1.4.1.351.140.1.2.11.1.1.3	INTEGER	read-create	The type of reachability from the advertising node to the address. This variable indicates either this ATM address ('internal') is a reachable ATM destination that is directly attached to the logical node advertising this address or an ATM address('exterior') that can be reached through a PNNI routing domain but which is not located in that routing domain.
INT cwspAdminStatus	1.3.6.1.4.1.351.140.1.2.1.1.1.1	INTEGER	read-create	The administrative status of the interface. inService (1) means that the interface is operational while outService (2) indicates that the interface is put out of service by the administrator.
C32 cwspAlertRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.13	Counter32	read-only	Number of ALERT messages received on this interface.
C32 cwspAlertXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.35	Counter32	read-only	Number of ALERT messages transmitted from this interface.
ADR cwspAtmAddress	1.3.6.1.4.1.351.140.1.2.11.1.1.1	AtmAddress	not-accessible	The value of the ATM End System Address.
cwspCacConfig	1.3.6.1.4.1.351.140.1.2.2
cwspCacConfigEntry	1.3.6.1.4.1.351.140.1.2.2.1.1		not-accessible	An entry contains CAC information.
cwspCacConfigGrp	1.3.6.1.4.1.351.140.3.2.3			A collection of objects providing information about CAC information of a interface.
cwspCacConfigTable	1.3.6.1.4.1.351.140.1.2.2.1		not-accessible	A table specifying the CAC(Connection Admission Control) information for each interface.
cwspCall	1.3.6.1.4.1.351.140.1.2.8
INT cwspCallBearerClass	1.3.6.1.4.1.351.140.1.2.8.1.1.15	INTEGER	read-only	This object shows the Bearer Class of the Call. It could be BcobA, BcobC, BcobX or VP Service
I32 cwspCallBwdCdvt	1.3.6.1.4.1.351.140.1.2.8.1.1.29	Integer32	read-only	This object shows the Cell Delay Variation Tolerance in the backward direction for the call, for PCR and SCR.
INT cwspCallBwdConformance	1.3.6.1.4.1.351.140.1.2.8.1.1.25	INTEGER	read-only	This object shows the conformance of the call to the traffic sets in the backward direction. It can be CBR.1, CBR.2, CBR.3, VBR.1 VBR.2, VBR.3, ABR, UBR.1 or UBR.2. This is as defined in ATMF Traffic Management 4.0 specification.
INT cwspCallBwdFrameDiscard	1.3.6.1.4.1.351.140.1.2.8.1.1.30	INTEGER	read-only	This object shows if the Frame Discard is enabled or disabled in the backward direction for the call.
I32 cwspCallBwdMbs	1.3.6.1.4.1.351.140.1.2.8.1.1.28	Integer32	read-only	This object shows the Maximum Burst Size of the call in the backward direction.
I32 cwspCallBwdPcr	1.3.6.1.4.1.351.140.1.2.8.1.1.26	Integer32	read-only	This object shows the Peak Cell Rate in the backward direction of the call.
I32 cwspCallBwdScr	1.3.6.1.4.1.351.140.1.2.8.1.1.27	Integer32	read-only	This object shows the Sustainable Cell Rate in the backward direction of the call.
ADR cwspCallCalledAddress	1.3.6.1.4.1.351.140.1.2.8.1.1.6	AtmAddress	read-only	This object shows the Called Party Address of the call.
ADR cwspCallCalledSubAddr	1.3.6.1.4.1.351.140.1.2.8.1.1.8	AtmAddress	read-only	This object shows the Called Party Subaddress of the call.
ADR cwspCallCallingAddress	1.3.6.1.4.1.351.140.1.2.8.1.1.5	AtmAddress	read-only	This object shows the Calling Party Address of the call.
ADR cwspCallCallingSubAddr	1.3.6.1.4.1.351.140.1.2.8.1.1.7	AtmAddress	read-only	This object shows the Calling Party Subaddress of the call.
I32 cwspCallCallRef	1.3.6.1.4.1.351.140.1.2.8.1.1.4	Integer32	read-only	This object shows the Call Reference value of the call on this interface.
INT cwspCallCastType	1.3.6.1.4.1.351.140.1.2.8.1.1.17	INTEGER	read-only	This object shows the Cast Type of the call, which can be a Point-to-Point (p2p), Point-to-MultiPoint (p2mp) or MultiPoint-to-Point (mp2p) call.
INT cwspCallClipSusceptibility	1.3.6.1.4.1.351.140.1.2.8.1.1.18	INTEGER	read-only	This object shows Susceptibility to Clipping. It can be susceptible or not susceptible.
cwspCallEntry	1.3.6.1.4.1.351.140.1.2.8.1.1		not-accessible	This object shows the multiple key index to get the Call record information. The key comprise of Interface Index, VPI/VCI value and Call Reference Value for the call.
I32 cwspCallFwdCdvt	1.3.6.1.4.1.351.140.1.2.8.1.1.23	Integer32	read-only	This object shows the Cell Delay Variation Tolerance(cdvt) in the forward direction for the call, for PCR and SCR.
INT cwspCallFwdConformance	1.3.6.1.4.1.351.140.1.2.8.1.1.19	INTEGER	read-only	This object shows the conformance of the call to the traffic sets in the forward direction. It can be CBR.1, CBR.2, CBR.3, VBR.1 VBR.2, VBR.3, ABR, UBR.1 or UBR.2. This is as defined in ATMF Traffic Management 4.0 specification.
INT cwspCallFwdFrameDiscard	1.3.6.1.4.1.351.140.1.2.8.1.1.24	INTEGER	read-only	This object shows if the Frame Discard is enabled or disabled in the forward direction for the call
I32 cwspCallFwdMbs	1.3.6.1.4.1.351.140.1.2.8.1.1.22	Integer32	read-only	This object shows the Maximum Burst Size(mbs) of the call in the forward direction.
I32 cwspCallFwdPcr	1.3.6.1.4.1.351.140.1.2.8.1.1.20	Integer32	read-only	This object shows the Peak Cell Rate(pcr) in the forward direction of the call.
I32 cwspCallFwdScr	1.3.6.1.4.1.351.140.1.2.8.1.1.21	Integer32	read-only	This object shows the Sustainable Cell Rate(scr) in the forward direction of the call.
cwspCallGrp	1.3.6.1.4.1.351.140.3.2.6			A collection of objects providing information about the p2p or p2mp SVC/SPVC calls and associated parameters.
I32 cwspCallLeafReference	1.3.6.1.4.1.351.140.1.2.8.1.1.3	Integer32	not-accessible	This object shows the value of the Leaf Reference (EndPointReference) of the Call on this interface.
I32 cwspCallMaxBwdCdv	1.3.6.1.4.1.351.140.1.2.8.1.1.34	Integer32	read-only	This object shows the Maximum Cell Delay Variation in the backward direction for this call on this interface.
I32 cwspCallMaxBwdClr	1.3.6.1.4.1.351.140.1.2.8.1.1.35	Integer32	read-only	This object shows the Maximum Cell Loss Ratio in the backward direction for this call on this interface.
I32 cwspCallMaxCtd	1.3.6.1.4.1.351.140.1.2.8.1.1.31	Integer32	read-only	This object shows the Maximum Cell Transfer Delay for the call on this interface.
I32 cwspCallMaxFwdCdv	1.3.6.1.4.1.351.140.1.2.8.1.1.32	Integer32	read-only	This object shows the Maximum Cell Delay Variation in the forward direction for this call on this interface.
I32 cwspCallMaxFwdClr	1.3.6.1.4.1.351.140.1.2.8.1.1.33	Integer32	read-only	This object shows the Maximum Cell Loss Ratio in the forward direction for this call on this interface.
I32 cwspCallOtherIntfCallRef	1.3.6.1.4.1.351.140.1.2.8.1.1.12	Integer32	read-only	This object shows the Call Reference of the call on the partner interface.
I32 cwspCallOtherIntfIndex	1.3.6.1.4.1.351.140.1.2.8.1.1.9	Integer32	read-only	This object shows the Other Interface of the call. Generally, this would be the outgoing/egress interface for the call.
I32 cwspCallOtherIntfVci	1.3.6.1.4.1.351.140.1.2.8.1.1.11	Integer32	read-only	This object shows The VCI of the call on the partner o interface. The value should be in the range of 32-65535 (0=SPVP).
I32 cwspCallOtherIntfVpi	1.3.6.1.4.1.351.140.1.2.8.1.1.10	Integer32	read-only	This object shows the VPI of the call on the partner interface.
C32 cwspCallProcRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.2	Counter32	read-only	Number of CALL PROCEEDING messages received on this interface.
C32 cwspCallProcXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.24	Counter32	read-only	Number of CALL PROCEEDING messages transmitted from this interface.
INT cwspCallServiceCategory	1.3.6.1.4.1.351.140.1.2.8.1.1.16	INTEGER	read-only	This object shows the service category of the call, which can be CBR, rtVBR, nrtVBR, ABR or UBR
TIM cwspCallStartTime	1.3.6.1.4.1.351.140.1.2.8.1.1.14	TimeStamp	read-only	This object shows the start time of the call. This is the timestamp when the Setup Message (or Add Party Message) was first received on this interface.
cwspCallStats	1.3.6.1.4.1.351.140.1.2.5
cwspCallStatsEntry	1.3.6.1.4.1.351.140.1.2.5.1.1		not-accessible	An entry contains SVC/SPVC call statistics
cwspCallStatsGrp	1.3.6.1.4.1.351.140.3.2.4			A collection of objects providing information about call statistics of a interface.
cwspCallStatsTable	1.3.6.1.4.1.351.140.1.2.5.1		not-accessible	This Table contains objects showing the Statistics for SVC/SPVC calls on a given interface.
cwspCallTable	1.3.6.1.4.1.351.140.1.2.8.1		not-accessible	This Table contains the objects which show parameters associated with a Point-to-Point(p2p) or Point-to-MultiPoint (p2mp) SVC/SPVC call.
INT cwspCallType	1.3.6.1.4.1.351.140.1.2.8.1.1.13	INTEGER	read-only	This object shows the Call Type for the call on this interface. The call type could be SVC or SPVC.
I32 cwspCallVci	1.3.6.1.4.1.351.140.1.2.8.1.1.2	Integer32	not-accessible	This object shows The VCI value of the call on this interface. The value should be in the range of 32-65535 (0=SPVP).
I32 cwspCallVpi	1.3.6.1.4.1.351.140.1.2.8.1.1.1	Integer32	not-accessible	This object shows the VPI value of the call on this interface.
cwspConfig	1.3.6.1.4.1.351.140.1.2.1
cwspConfigEntry	1.3.6.1.4.1.351.140.1.2.1.1.1		not-accessible	An entry in the interface configuration table containing information about an interface
cwspConfigGrp	1.3.6.1.4.1.351.140.3.2.2			A collection of objects providing information about the controller interface operation and associated parameters.
cwspConfigGrp2	1.3.6.1.4.1.351.140.3.2.20			A collection of objects providing information about the controller interface operation and associated parameters.
cwspConfigGrp3	1.3.6.1.4.1.351.140.3.2.21			A collection of objects providing information about the controller interface operation and associated parameters.
cwspConfigTable	1.3.6.1.4.1.351.140.1.2.1.1		not-accessible	The Interface configuration table collects attributes that affect the operation of the controller interface. There is a single row for each interface that the managed system is expected to be added or managed.
ROW cwspConfigTableRowStatus	1.3.6.1.4.1.351.140.1.2.1.1.1.29	RowStatus	read-create	Used to create and delete the Interface. However, only createAndGo, destroy, active and notInService are supported. NMS should only use createAndGo to create a row and destroy to delete a row. The managed device will either return active or notInService for a row status.
C32 cwspConnectAckRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.4	Counter32	read-only	Number of CONNECT ACK messages received on this interface.
C32 cwspConnectAckXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.26	Counter32	read-only	Number of CONNECT ACK messages transmitted from this interface.
C32 cwspConnectRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.3	Counter32	read-only	Number of CONNECT messages received on this interface.
C32 cwspConnectXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.25	Counter32	read-only	Number of CONNECT messages transmitted from this interface.
cwspConnTrace	1.3.6.1.4.1.351.140.1.2.14
I32 cwspConnTraceAvail	1.3.6.1.4.1.351.140.1.2.14.1	Integer32	read-only	This object tells the number of calls can be traced concurrently. Depending on the system resource, this object may vary sometime to time. NMS should query this object to ensure there is system resource available before creating a row in the cwspConnTraceCntlTable.
I32 cwspConnTraceCallRef	1.3.6.1.4.1.351.140.1.2.14.3.1.6	Integer32	read-only	This object shows the Call Reference value of the call on this interface.
cwspConnTraceCntlEntry	1.3.6.1.4.1.351.140.1.2.14.3.1		not-accessible	This object controls the connection trace creation. NMS needs to acquire the next index available to create a row. In addition, NMS needs to provide all read-create objects in the same pdu with RowStatus to be CreateAndGo.
cwspConnTraceCntlTable	1.3.6.1.4.1.351.140.1.2.14.3		not-accessible	This Table contains the objects which control the creation of connection trace for the existing SVC call.
I32 cwspConnTraceDataIndex	1.3.6.1.4.1.351.140.1.2.14.4.1.1	Integer32	not-accessible	Along with cwspConnTraceIndex, this object specified an unique entry in the cwspConnTraceTable.
I32 cwspConnTraceDestCallRef	1.3.6.1.4.1.351.140.1.2.14.3.1.10	Integer32	read-only	This object shows the endpoint call reference on this interface.
I32 cwspConnTraceDestVci	1.3.6.1.4.1.351.140.1.2.14.3.1.9	Integer32	read-only	This object shows the endpoint VCI value of the call on this interface.
I32 cwspConnTraceDestVpi	1.3.6.1.4.1.351.140.1.2.14.3.1.8	Integer32	read-only	This object shows the endpoint VPI value of the call on this interface.
I32 cwspConnTraceEgressCallRef	1.3.6.1.4.1.351.140.1.2.14.4.1.6	Integer32	read-only	This object shows the Egress port's call reference.
OCT cwspConnTraceEgressPhyPortId	1.3.6.1.4.1.351.140.1.2.14.4.1.7	OCTET STRING	read-only	This object shows the Egress port's physical port Identifier for the traversed node; if this object is 0 meaning that the destination node for the traced connection has been reached. the meaning for the bytes are: first byte -- flag (used by CLI to decode the rest of bytes ) 2nd byte -- shelf 3rd & 4th bytes -- slot 5th byte -- subslot 6th & 7th bytes -- port 8th byte -- subport
PNN cwspConnTraceEgressPortId	1.3.6.1.4.1.351.140.1.2.14.4.1.3	PnniPortId	read-only	This object represents 4 bytes logical port ID of the traversed node. When 0 is specified, the destination node for the trace is reached.
I32 cwspConnTraceEgressVci	1.3.6.1.4.1.351.140.1.2.14.4.1.5	Integer32	read-only	This object shows the Egress port's VCI value for the traced connection
I32 cwspConnTraceEgressVpi	1.3.6.1.4.1.351.140.1.2.14.4.1.4	Integer32	read-only	This object shows the Egress port's VPI value for the traced connection.
cwspConnTraceEntry	1.3.6.1.4.1.351.140.1.2.14.4.1		not-accessible	A conceptual row of the cwspConnTraceTable used to return information about all the nodes belongs to the connection which search criteria is corresponding to instance of the cwspConnTraceCntlTable.
cwspConnTraceGrp	1.3.6.1.4.1.351.140.3.2.16			A collection of objects providing trace information about SVC/PNNI connnection.
cwspConnTraceGrp2	1.3.6.1.4.1.351.140.3.2.19			A collection of objects providing trace information about SVC/PNNI connnection.
NUM cwspConnTraceifIndex	1.3.6.1.4.1.351.140.1.2.14.3.1.2	InterfaceIndex	read-create	The 'ifIndex' indicates the port to a trace connection.
I32 cwspConnTraceIndex	1.3.6.1.4.1.351.140.1.2.14.3.1.1	Integer32	not-accessible	Index to a row of connection trace.
T/F cwspConnTraceLastNode	1.3.6.1.4.1.351.140.1.2.14.4.1.8	TruthValue	read-only	This value indicates if this entry contains the information about the last node where this trace ends. If it is the last node, this value is 'true(1)' or it is 'false(2)'.
I32 cwspConnTraceLeafRef	1.3.6.1.4.1.351.140.1.2.14.3.1.7	Integer32	read-create	This object shows the value of the Leaf Reference (EndPointReference) of the Call on this interface, this value is used to support p2mp call trace. For p2p call, this value should be set as 0 by NMS.
I32 cwspConnTraceNextIndex	1.3.6.1.4.1.351.140.1.2.14.2	Integer32	read-only	When creating a row in the cwspConnTraceCntlTable, NMS should query this object to obtain the index value to be used for row creation.
PNN cwspConnTraceNodeId	1.3.6.1.4.1.351.140.1.2.14.4.1.2	PnniNodeId	read-only	This octet string represents 22 bytes nodeId in the traced connection.
ROW cwspConnTraceQueryStatus	1.3.6.1.4.1.351.140.1.2.14.3.1.12	RowStatus	read-create	This object used to manage rows in this table. However, only CreateAndGo, NotInService, Active, and Destroy are start up the trace. To remove a row, NMS set this value to Destroy. The managed device will either return Active or NotInService.
INT cwspConnTraceResultStatus	1.3.6.1.4.1.351.140.1.2.14.3.1.11	INTEGER	read-only	This object shows the result of tracing the call. NMS should get positive result (i.e. traceCompleted) for this attribute before query the cwspConnTraceTable.
I32 cwspConnTraceSrcVci	1.3.6.1.4.1.351.140.1.2.14.3.1.4	Integer32	read-create	This object shows The VCI value of the starting point on this interface. The value should be in the range of 32-65535 (0=SPVP).
I32 cwspConnTraceSrcVpi	1.3.6.1.4.1.351.140.1.2.14.3.1.3	Integer32	read-create	This object shows the VPI value of the starting point on this interface.
cwspConnTraceTable	1.3.6.1.4.1.351.140.1.2.14.4		not-accessible	This table contains the objects which show the traversed node information in the existing SVC call.
INT cwspConnTraceType	1.3.6.1.4.1.351.140.1.2.14.3.1.5	INTEGER	read-create	Setting this object to either p2p or p2mp to specify tracing a p2p or p2mp connection.
INT cwspCountReset	1.3.6.1.4.1.351.140.1.2.5.1.1.1	INTEGER	read-write	Writing a 2 to this object resets all counters.
I32 cwspDefaultCdvtAbr	1.3.6.1.4.1.351.140.1.2.2.1.1.34	Integer32	read-write	This is the default CDVT for ABR service.
I32 cwspDefaultCdvtCbr	1.3.6.1.4.1.351.140.1.2.2.1.1.31	Integer32	read-write	This is the default CDVT for CBR service.
I32 cwspDefaultCdvtNrtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.33	Integer32	read-write	This is the default CDVT non-real time VBR service.
I32 cwspDefaultCdvtRtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.32	Integer32	read-write	This is the default CDVT real time VBR service.
I32 cwspDefaultCdvtUbr	1.3.6.1.4.1.351.140.1.2.2.1.1.35	Integer32	read-write	This is the default CDVT for UBR service.
I32 cwspDefaultMbsNrtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.37	Integer32	read-write	This is the default MBS non-real time VBR service.
I32 cwspDefaultMbsRtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.36	Integer32	read-write	This is the default MBS real time VBR service.
C32 cwspDropPtyRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.18	Counter32	read-only	Number of DROP PARTY messages received on this interface.
C32 cwspDropPtyXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.40	Counter32	read-only	Number of DROP PARTY messages transmitted from this interface.
T/F cwspEnhancedIisp	1.3.6.1.4.1.351.140.1.2.1.1.1.28	TruthValue	read-create	Indicates whether the enhanced features for IISP are enabled or disabled.
T/F cwspIlmiAddrRegEnable	1.3.6.1.4.1.351.140.1.2.1.1.1.5	TruthValue	read-create	Indicates whether ILMI address registration is enabled or disabled.
T/F cwspIlmiAttachmentPoint	1.3.6.1.4.1.351.140.1.2.1.1.1.32	TruthValue	read-create	Indicates whether detection of loss of attachment procedures are enabled on this interface. When set to true, then standard ILMI procedures are employed to detect loss of attachment point. If set to false, then ILMI protocol on the interface does not detect the loss of attachment.
T/F cwspIlmiAutoConfEnable	1.3.6.1.4.1.351.140.1.2.1.1.1.6	TruthValue	read-create	Indicates whether auto-configuration of the interface is turned on or off. If auto-configuration is enabled, then the interface comes up using the ILMI auto-configuration.
T/F cwspIlmiLocalAttrStd	1.3.6.1.4.1.351.140.1.2.1.1.1.33	TruthValue	read-create	Indicates whether on modification of local attributes, procedures as recommended by ILMI 4.0 specification are followed or cisco proprietery procedures are followed. When set to true, the standard ILMI procedures are followed.
T/F cwspIlmiSecureLink	1.3.6.1.4.1.351.140.1.2.1.1.1.31	TruthValue	read-create	Indicates whether ILMI Secure Link Protocol is enabled or disabled. When secure link protocol is enabled, loss in ILMI connectivity is treated as loss of attachment point which results in all SVCs/SVPs being released on the interface.
T/F cwspIlmiServRegEnable	1.3.6.1.4.1.351.140.1.2.1.1.1.7	TruthValue	read-create	Indicates whether service registry is enabled or disabled on the interface.
T/F cwspIlmiUCSMEnable	1.3.6.1.4.1.351.140.1.2.1.1.1.34	TruthValue	read-create	Indicates whether ILMI user connection status monitoring is enabled or disabled.
C32 cwspInCallAttempts	1.3.6.1.4.1.351.140.1.2.5.1.1.2	Counter32	read-only	This object shows the number of incoming Signaling messages (Setup and Add Party) received by the switching node on this interface for Call establishment.
C32 cwspInCallEstabs	1.3.6.1.4.1.351.140.1.2.5.1.1.3	Counter32	read-only	This object shows the number of incoming Signaling Messages (Connect and Add Party Ack) received by the switching node on this interface which marks that a call has been successfully established.
C32 cwspInCallFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.4	Counter32	read-only	This object shows the total number of incoming Point-to-Point (p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC call attempts failed on this interface.
C32 cwspIncorrectMsgRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.20	Counter32	read-only	Number of Incorrect messages received on this interface.
C32 cwspInCrankbacks	1.3.6.1.4.1.351.140.1.2.5.1.1.9	Counter32	read-only	This object shows the number of Crankback IEs received on this interface for incoming Point-to-Point(p2p) and Point-to-MultiPoint (p2mp) SVC/SPVC call attempts.
C32 cwspInFilterFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.5	Counter32	read-only	This object shows the number of incoming Point-to-Point(p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC call attempts which failed due to address filtering on this interface.
C32 cwspInResrcFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.7	Counter32	read-only	This object shows the number of incoming Point-to-Point(p2p) and Point-to-MulitPoint(p2mp) SVC/SPVC call attempts on this interface which failed because there were not enough resources as requested in the parameters of the call.
C32 cwspInRouteFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.6	Counter32	read-only	This object shows the number of incoming Point-to-Point(p2p) and Point-to-MulitPoint(p2mp) SVC/SPVC call attempts on this interface which failed because there was no route to the destination available.
C32 cwspInTimerFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.8	Counter32	read-only	This object shows the number of signaling timers timed out for incoming Point-to-Point(p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC calls on this interface.
C32 cwspLastCause	1.3.6.1.4.1.351.140.1.2.6.1.1.22	Counter32	read-only	to indicate the last cause of release or cranckback.
I32 cwspLastDiagnostic	1.3.6.1.4.1.351.140.1.2.6.1.1.23	Integer32	read-only	to indicate the last diagnostic of release or cranckback.
cwspLoad	1.3.6.1.4.1.351.140.1.2.13
I32 cwspLoadAvlBwAbr	1.3.6.1.4.1.351.140.1.2.13.1.1.11	Integer32	read-only	The available bandwith for ABR service.
I32 cwspLoadAvlBwCbr	1.3.6.1.4.1.351.140.1.2.13.1.1.8	Integer32	read-only	The available bandwith for CBR service.
I32 cwspLoadAvlBwNrtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.10	Integer32	read-only	The available bandwith for non-real time VBR service.
I32 cwspLoadAvlBwRtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.9	Integer32	read-only	The available bandwith for real time VBR service.
I32 cwspLoadAvlBwUbr	1.3.6.1.4.1.351.140.1.2.13.1.1.12	Integer32	read-only	The available bandwith for UBR service.
I32 cwspLoadAvlVcAbr	1.3.6.1.4.1.351.140.1.2.13.1.1.17	Integer32	read-only	The number of VCs used by ABR service.
I32 cwspLoadAvlVcCbr	1.3.6.1.4.1.351.140.1.2.13.1.1.14	Integer32	read-only	The number of VCs used by CBR service.
I32 cwspLoadAvlVcNrtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.16	Integer32	read-only	The number of VCs used by non-real time VBR service.
I32 cwspLoadAvlVcRtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.15	Integer32	read-only	The number of VCs used by real time VBR service.
I32 cwspLoadAvlVcUbr	1.3.6.1.4.1.351.140.1.2.13.1.1.18	Integer32	read-only	The number of VCs used by UBR service.
I32 cwspLoadBwAvail	1.3.6.1.4.1.351.140.1.2.13.1.1.7	Integer32	read-only	The total available bandwidth of the interface.
I32 cwspLoadBwTotal	1.3.6.1.4.1.351.140.1.2.13.1.1.1	Integer32	read-only	The total bandwidth of the interface.
I32 cwspLoadCdvAbr	1.3.6.1.4.1.351.140.1.2.13.1.1.27	Integer32	read-only	The cell delay variation of ABR service.
I32 cwspLoadCdvCbr	1.3.6.1.4.1.351.140.1.2.13.1.1.24	Integer32	read-only	The cell delay variation of CBR service.
I32 cwspLoadCdvNrtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.26	Integer32	read-only	The cell delay variation of non-real time VBR service.
I32 cwspLoadCdvRtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.25	Integer32	read-only	The cell delay variation of real time VBR service.
I32 cwspLoadCdvUbr	1.3.6.1.4.1.351.140.1.2.13.1.1.28	Integer32	read-only	The cell delay variation of UBR service.
I32 cwspLoadClr01Abr	1.3.6.1.4.1.351.140.1.2.13.1.1.37	Integer32	read-only	The cell loss ratio-1 of ABR service, -1 implies N/A.
I32 cwspLoadClr01Cbr	1.3.6.1.4.1.351.140.1.2.13.1.1.34	Integer32	read-only	The cell loss ratio-1 of CBR service, -1 implies N/A.
I32 cwspLoadClr01NrtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.36	Integer32	read-only	The cell loss ratio-1 of non-real time VBR service, -1 implies N/A.
I32 cwspLoadClr01RtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.35	Integer32	read-only	The cell loss ratio-1 of real time VBR service, -1 implies N/A.
I32 cwspLoadClr01Ubr	1.3.6.1.4.1.351.140.1.2.13.1.1.38	Integer32	read-only	The cell loss ratio-1 of UBR service, -1 implies N/A.
I32 cwspLoadClr0Abr	1.3.6.1.4.1.351.140.1.2.13.1.1.32	Integer32	read-only	The cell loss ratio-0 of ABR service, -1 implies N/A.
I32 cwspLoadClr0Cbr	1.3.6.1.4.1.351.140.1.2.13.1.1.29	Integer32	read-only	The cell loss ratio-0 of CBR service, -1 implies N/A.
I32 cwspLoadClr0NrtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.31	Integer32	read-only	The cell loss ratio-0 of non-real time VBR service, -1 implies N/A.
I32 cwspLoadClr0RtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.30	Integer32	read-only	The cell loss ratio-0 of real time VBR service, -1 implies N/A.
I32 cwspLoadClr0Ubr	1.3.6.1.4.1.351.140.1.2.13.1.1.33	Integer32	read-only	The cell loss ratio-0 of UBR service, -1 implies N/A.
I32 cwspLoadCtdAbr	1.3.6.1.4.1.351.140.1.2.13.1.1.22	Integer32	read-only	The cell transfer delay of ABR service.
I32 cwspLoadCtdCbr	1.3.6.1.4.1.351.140.1.2.13.1.1.19	Integer32	read-only	The cell transfer delay of CBR service.
I32 cwspLoadCtdNrtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.21	Integer32	read-only	The cell transfer delay of non-real time VBR service.
I32 cwspLoadCtdRtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.20	Integer32	read-only	The cell transfer delay of real time VBR service.
I32 cwspLoadCtdUbr	1.3.6.1.4.1.351.140.1.2.13.1.1.23	Integer32	read-only	The cell transfer delay of UBR service.
cwspLoadEntry	1.3.6.1.4.1.351.140.1.2.13.1.1		not-accessible	An entry contains the load information.
cwspLoadGrp	1.3.6.1.4.1.351.140.3.2.9			A collection of objects providing information about load information and associated parameters of a interface.
I32 cwspLoadMaxBwAbr	1.3.6.1.4.1.351.140.1.2.13.1.1.5	Integer32	read-only	The maximum bandwith for ABR service.
I32 cwspLoadMaxBwCbr	1.3.6.1.4.1.351.140.1.2.13.1.1.2	Integer32	read-only	The Maximum bandwith for CBR service.
I32 cwspLoadMaxBwNrtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.4	Integer32	read-only	The maximum bandwith for non-real time VBR service.
I32 cwspLoadMaxBwRtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.3	Integer32	read-only	The maximum bandwith for real time VBR service.
I32 cwspLoadMaxBwUbr	1.3.6.1.4.1.351.140.1.2.13.1.1.6	Integer32	read-only	The maximum bandwith for UBR service.
I32 cwspLoadMinGurCrAbr	1.3.6.1.4.1.351.140.1.2.13.1.1.42	Integer32	read-only	The minimum guaranteed cell rate capacity of ABR service.
I32 cwspLoadMinGurCrCbr	1.3.6.1.4.1.351.140.1.2.13.1.1.39	Integer32	read-only	The minimum guaranteed cell rate capacity of CBR service.
I32 cwspLoadMinGurCrNrtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.41	Integer32	read-only	The minimum guaranteed cell rate capacity of non-real time VBR service.
I32 cwspLoadMinGurCrRtVbr	1.3.6.1.4.1.351.140.1.2.13.1.1.40	Integer32	read-only	The minimum guaranteed cell rate capacity of real time VBR service.
I32 cwspLoadMinGurCrUbr	1.3.6.1.4.1.351.140.1.2.13.1.1.43	Integer32	read-only	The minimum guaranteed cell rate capacity of UBR service.
cwspLoadTable	1.3.6.1.4.1.351.140.1.2.13.1		not-accessible	A table specifying the load information for each interface.
I32 cwspLoadVcAvail	1.3.6.1.4.1.351.140.1.2.13.1.1.13	Integer32	read-only	The total number of available VCs of the interface.
I32 cwspMaxBwAbr	1.3.6.1.4.1.351.140.1.2.2.1.1.9	Integer32	read-write	This is the maximum bandwidth for ABR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxBwCbr	1.3.6.1.4.1.351.140.1.2.2.1.1.6	Integer32	read-write	This is the maximum bandwidth for CBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxBwNrtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.8	Integer32	read-write	This is the maximum bandwidth for non-real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxBwRtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.7	Integer32	read-write	This is the maximum bandwidth for real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxBwUbr	1.3.6.1.4.1.351.140.1.2.2.1.1.10	Integer32	read-write	This is the maximum bandwidth for UBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxP2mpLeafs	1.3.6.1.4.1.351.140.1.2.1.1.1.21	Integer32	read-create	Indicates the maximum number of leaf VCs (for point-to-multipoint) allowed on the interface.
I32 cwspMaxP2mpRoots	1.3.6.1.4.1.351.140.1.2.1.1.1.20	Integer32	read-create	Indicates the maximum number of root VCs (for point-to-multipoint) allowed on the interface.
I32 cwspMaxP2pCalls	1.3.6.1.4.1.351.140.1.2.1.1.1.19	Integer32	read-create	Indicates the maximum number of point to point calls (including VCs and VPs allowed on the interface.
I32 cwspMaxSvccVci	1.3.6.1.4.1.351.140.1.2.1.1.1.25	Integer32	read-create	Indicates the maximum SVCC VCI configured on the interface.
I32 cwspMaxSvccVpi	1.3.6.1.4.1.351.140.1.2.1.1.1.23	Integer32	read-create	Indicates the maximum SVCC VPI configured on the interface.
I32 cwspMaxSvpcVpi	1.3.6.1.4.1.351.140.1.2.1.1.1.27	Integer32	read-create	Indicates the maximum SVPC VPI configured on the interface.
I32 cwspMaxVcAbr	1.3.6.1.4.1.351.140.1.2.2.1.1.19	Integer32	read-write	This is the maximum number of VCs for ABR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxVcBwAbr	1.3.6.1.4.1.351.140.1.2.2.1.1.29	Integer32	read-write	This is the maximum bandwidth allowed for a VC for ABR service. The value is in the unit of cells per second.
I32 cwspMaxVcBwCbr	1.3.6.1.4.1.351.140.1.2.2.1.1.26	Integer32	read-write	This is the maximum bandwidth allowed for a VC for real time CBR service. The value is in the unit of cells per second.
I32 cwspMaxVcBwNrtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.28	Integer32	read-write	This is the maximum bandwidth allowed for a VC for non-real time VBR service. The value is in the unit of cells per second.
I32 cwspMaxVcBwRtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.27	Integer32	read-write	This is the maximum bandwidth allowed for a VC for real time VBR service. The value is in the unit of cells per second.
I32 cwspMaxVcBwUbr	1.3.6.1.4.1.351.140.1.2.2.1.1.30	Integer32	read-write	This is the maximum bandwidth allowed for UBR service. The value is in the unit of cells per second.
I32 cwspMaxVcCbr	1.3.6.1.4.1.351.140.1.2.2.1.1.16	Integer32	read-write	This is the maximum number of VCs for CBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxVciBits	1.3.6.1.4.1.351.140.1.2.1.1.1.14	Integer32	read-only	The maximum number of active VCI bits on this ATM Interface.
I32 cwspMaxVcNrtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.18	Integer32	read-write	This is the maximum number of VCs for non-real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxVcRtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.17	Integer32	read-write	This is the maximum number of VCs for real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxVcUbr	1.3.6.1.4.1.351.140.1.2.2.1.1.20	Integer32	read-write	This is the maximum number of VCs for UBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMaxVpiBits	1.3.6.1.4.1.351.140.1.2.1.1.1.13	Integer32	read-only	The maximum number of active VPI bits on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), this value has no meaning and is set to zero.
I32 cwspMinBwAbr	1.3.6.1.4.1.351.140.1.2.2.1.1.14	Integer32	read-write	This is the minimum bandwidth for ABR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMinBwCbr	1.3.6.1.4.1.351.140.1.2.2.1.1.11	Integer32	read-write	This is the minimum bandwidth for CBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMinBwNrtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.13	Integer32	read-write	This is the minimum bandwidth for non-real time VBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMinBwRtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.12	Integer32	read-write	This is the minimum bandwidth for real time VBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMinBwUbr	1.3.6.1.4.1.351.140.1.2.2.1.1.15	Integer32	read-only	This is the minimum bandwidth for UBR service in percentage. The value for this variable is always 0.
I32 cwspMinSvccVci	1.3.6.1.4.1.351.140.1.2.1.1.1.24	Integer32	read-create	Indicates the minimum SVCC VCI configured on the interface.
I32 cwspMinSvccVpi	1.3.6.1.4.1.351.140.1.2.1.1.1.22	Integer32	read-create	Indicates the minimum SVCC VPI configured on the interface.
I32 cwspMinSvpcVpi	1.3.6.1.4.1.351.140.1.2.1.1.1.26	Integer32	read-create	Indicates the minimum SVPC VPI configured on the interface.
I32 cwspMinVcAbr	1.3.6.1.4.1.351.140.1.2.2.1.1.24	Integer32	read-write	This is the minimum number of VCs for ABR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMinVcCbr	1.3.6.1.4.1.351.140.1.2.2.1.1.21	Integer32	read-write	This is the minimum number of VCs for CBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. This variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMinVcNrtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.23	Integer32	read-write	This is the minimum number of VCs for non-real time VBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr,cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMinVcRtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.22	Integer32	read-write	This is the minimum number of VCs for real time VBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
I32 cwspMinVcUbr	1.3.6.1.4.1.351.140.1.2.2.1.1.25	Integer32	read-write	This is the minimum number of VCs for UBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
NET cwspNetPrefix	1.3.6.1.4.1.351.140.1.2.10.1.1.1	NetPrefix	not-accessible	The network prefix specified for use in ILMI address registration.
INT cwspNniVersion	1.3.6.1.4.1.351.140.1.2.1.1.1.16	INTEGER	read-create	An indication of the latest version of the ATM Forum PNNI Signaling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed.
C32 cwspNotifyRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.12	Counter32	read-only	Number of NOTIFY messages received on this interface.
C32 cwspNotifyXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.34	Counter32	read-only	Number of NOTIFY messages transmitted from this interface.
INT cwspOperAddrPlanSupported	1.3.6.1.4.1.351.140.1.2.15.1.1.19	INTEGER	read-only	The ATM address plan supported on a public UNI. For all other interfaces, the value is aesa.
cwspOperation	1.3.6.1.4.1.351.140.1.2.15
cwspOperationEntry	1.3.6.1.4.1.351.140.1.2.15.1.1		not-accessible	An entry in the interface operation table containing negotiated values of an interface
cwspOperationGrp	1.3.6.1.4.1.351.140.3.2.17			A collection of objects providing information about runtime negotiated values between platform, PNNI controller and peer on an interface.
cwspOperationTable	1.3.6.1.4.1.351.140.1.2.15.1		not-accessible	The Interface operation table contains the runtime negotiated values between platform, PNNI controller and peer on an interface
INT cwspOperDeviceType	1.3.6.1.4.1.351.140.1.2.15.1.1.10	INTEGER	read-only	This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2).
INT cwspOperFailReason	1.3.6.1.4.1.351.140.1.2.15.2	INTEGER	read-only	Defined SVC port failures. Note: this object is used as trap varbind only. The NMS applications should not issue SNMP get, get-next for this object.
INT cwspOperIfcSide	1.3.6.1.4.1.351.140.1.2.15.1.1.3	INTEGER	read-only	The IME type of the ATM device which is concluded from automatic interface type determination procedure.
INT cwspOperIfcType	1.3.6.1.4.1.351.140.1.2.15.1.1.2	INTEGER	read-only	The interface type of an interface publicUni -- Public User-Network Interface privateUni -- Private User-Network Interface iisp -- Interim Inter-Switch Signaling Protocol pnni -- Private Network-Network Interface aini -- ATM Inter-Network Interface enni -- Enhanced Network-Network Interface, a cisco proprietary interfac type.
T/F cwspOperIlmiEnable	1.3.6.1.4.1.351.140.1.2.15.1.1.1	TruthValue	read-only	The operational state of ILMI.
INT cwspOperIlmiVersion	1.3.6.1.4.1.351.140.1.2.15.1.1.11	INTEGER	read-only	An indication of the latest version of the ATM Forum ILMI Specification that is supported on this ATM Interface. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. If this object is not present, a version of the ILMI earlier than 4.0 is supported.
I32 cwspOperMaxSvccVci	1.3.6.1.4.1.351.140.1.2.15.1.1.17	Integer32	read-only	The maximum switched VCC VCI.
I32 cwspOperMaxSvccVpi	1.3.6.1.4.1.351.140.1.2.15.1.1.15	Integer32	read-only	The maximum switched VCC VPI.
I32 cwspOperMaxSvpcVpi	1.3.6.1.4.1.351.140.1.2.15.1.1.13	Integer32	read-only	The maximum switched VPC VPI.
I32 cwspOperMaxVCCs	1.3.6.1.4.1.351.140.1.2.15.1.1.5	Integer32	read-only	The maximum number of switched and permanent VCCs supported on this ATM interface
I32 cwspOperMaxVciBits	1.3.6.1.4.1.351.140.1.2.15.1.1.7	Integer32	read-only	The maximum number of active VCI bits on this ATM interface.
I32 cwspOperMaxVPCs	1.3.6.1.4.1.351.140.1.2.15.1.1.4	Integer32	read-only	The maximum number of switched and permanent VPCs supported on this ATM interface
I32 cwspOperMaxVpiBits	1.3.6.1.4.1.351.140.1.2.15.1.1.6	Integer32	read-only	The maximum number of active VPI bits on this ATM interface.
I32 cwspOperMinSvccVci	1.3.6.1.4.1.351.140.1.2.15.1.1.18	Integer32	read-only	The minimum switched VCC VCI.
I32 cwspOperMinSvccVpi	1.3.6.1.4.1.351.140.1.2.15.1.1.16	Integer32	read-only	The minimum switched VCC VPI.
I32 cwspOperMinSvpcVpi	1.3.6.1.4.1.351.140.1.2.15.1.1.14	Integer32	read-only	The minimum switched VPC VPI.
INT cwspOperNniSigVersion	1.3.6.1.4.1.351.140.1.2.15.1.1.12	INTEGER	read-only	An indication of the latest version of the ATM Forum PNNI Signaling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. Note that 'enni' is not a signaling protocol.
INT cwspOperStatus	1.3.6.1.4.1.351.140.1.2.1.1.1.2	INTEGER	read-only	The operational state of the interface. This status is derived from the physical state of the interface. failed (2) indicates that the interface has failed. ok (1) indicates that the interface is in operational status, while other (3) denotes that the interface is in an unknown state.
INT cwspOperUniType	1.3.6.1.4.1.351.140.1.2.15.1.1.8	INTEGER	read-only	The type of the ATM device, either public or private.
INT cwspOperUniVersion	1.3.6.1.4.1.351.140.1.2.15.1.1.9	INTEGER	read-only	An indication of the latest version of the ATM Forum UNI Signaling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed.
C32 cwspOutCallAttempts	1.3.6.1.4.1.351.140.1.2.5.1.1.10	Counter32	read-only	This object shows the number of outgoing Signaling messages (Setup and Add Party) on this interface for Call establishment.
C32 cwspOutCallEstabs	1.3.6.1.4.1.351.140.1.2.5.1.1.11	Counter32	read-only	This object shows the number of outgoing Signaling messages (Connect and Add Party Ack) which mark the call being established on this interface
C32 cwspOutCallFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.12	Counter32	read-only	This object shows the total number of outgoing Signaling messages for Point-to-Point and Point-to-MultiPoint call establishment on this interface which failed.
C32 cwspOutCrankbacks	1.3.6.1.4.1.351.140.1.2.5.1.1.17	Counter32	read-only	This object shows the number of Crankback IEs being sent on this interface for outgoing signaling Release messages. This is generated on the node which generates the Crankback IEs.
C32 cwspOutFilterFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.13	Counter32	read-only	This object shows the number of outgoing Signaling messages for call establishment on this interface which failed the address filtering.
C32 cwspOutResrcFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.15	Counter32	read-only	This object shows the number of outgoing Signaling messages for call establishment on this interface which failed because the resource requested was not available.
C32 cwspOutRouteFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.14	Counter32	read-only	This object shows the number of outgoing Signaling messages for call establishment on this interface which failed because the route was not available.
C32 cwspOutTimerFailures	1.3.6.1.4.1.351.140.1.2.5.1.1.16	Counter32	read-only	This object shows the number of Signaling timers timed-out on this interface for outgoing signaling messages.
STR cwspPhyIdentifier	1.3.6.1.4.1.351.140.1.2.1.1.1.8	DisplayString	read-create	Indicates the physical identification of the interface. Mandatory when the port is provisioned for the first time through SNMP.
I32 cwspPnniControllerPhySlot	1.3.6.1.4.1.351.140.1.1.9	Integer32	read-only	The pnni controller physical location for MGX or BPX-SES. Note: this object is only used in the trap varbind, snmp get operation is meaningless.
INT cwspPnniControllerStatus	1.3.6.1.4.1.351.140.1.1.8	INTEGER	read-only	The administrative status of the pnni controller. Note: this object is only used in the trap varbind, snmp get operation is meaningless.
CWS cwspPnniStndbyControllerStatus	1.3.6.1.4.1.351.140.1.1.7	CwspControllerState	read-only	The administrative status for the standby controller.
cwspPrefix	1.3.6.1.4.1.351.140.1.2.10
cwspPrefixEntry	1.3.6.1.4.1.351.140.1.2.10.1.1		not-accessible	Information about a single network prefix contained in the prefix table.
cwspPrefixGrp	1.3.6.1.4.1.351.140.3.2.8			A table specifying the network prefix(es) used for ILMI address registration.
ROW cwspPrefixRowStatus	1.3.6.1.4.1.351.140.1.2.10.1.1.2	RowStatus	read-create	Used to create, delete, activate and de-activate network prefixes used in ILMI address registration.
cwspPrefixTable	1.3.6.1.4.1.351.140.1.2.10.1		not-accessible	A table specifying the network prefix(es) used for ILMI address registration.
C32 cwspProgressRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.14	Counter32	read-only	Number of PROGRESS messages received on this interface.
C32 cwspProgressXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.36	Counter32	read-only	Number of PROGRESS messages transmitted from this interface.
cwspRegAddress	1.3.6.1.4.1.351.140.1.2.12
cwspRegAddressEntry	1.3.6.1.4.1.351.140.1.2.12.1.1		not-accessible	An entry in the ATM Interface Registered Address table.
cwspRegAddressGrp	1.3.6.1.4.1.351.140.3.2.14			A collection of objects providing information about registed ATM address.
INT cwspRegAddressOrgSscope	1.3.6.1.4.1.351.140.1.2.12.1.1.2	INTEGER	read-write	This object indicates the organizational scope for the referenced address. The information of the referenced address shall not be distributed outside the indicated scope. The default values for organizational scope are localNetwork(1) for ATM group addresses, and global(15) for individual addresses.
cwspRegAddressTable	1.3.6.1.4.1.351.140.1.2.12.1		not-accessible	This table contains a list of ATM addresses that can be used for calls to and from a given interface by a switch or service. The ATM addresses are registered by the endsystem via ILMI. ILMI registered addresses cannot be deleted using this table. This table only applies to switches and network services.
ADR cwspRegAtmAddress	1.3.6.1.4.1.351.140.1.2.12.1.1.1	AtmAddress	read-only	An address registered for a given switch or service interface.
C32 cwspReleaseComplRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.7	Counter32	read-only	Number of RELEASE COMPLETE messages received on this interface.
C32 cwspReleaseComplXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.29	Counter32	read-only	Number of RELEASE COMPLETE messages transmitted from this interface.
C32 cwspReleaseRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.6	Counter32	read-only	Number of RELEASE messages received on this interface.
C32 cwspReleaseXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.28	Counter32	read-only	Number of RELEASE messages transmitted from this interface.
C32 cwspRestartAckRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.9	Counter32	read-only	Number of RESTART ACK messages received on this interface.
C32 cwspRestartAckXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.31	Counter32	read-only	Number of RESTART ACK messages transmitted from this interface.
C32 cwspRestartRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.8	Counter32	read-only	Number of RESTART messages received on this interface.
C32 cwspRestartXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.30	Counter32	read-only	Number of RESTART messages transmitted from this interface.
cwspRoutingGrp	1.3.6.1.4.1.351.140.3.2.15			A collection of objects providing information about PNNI topology.
I32 cwspRoutingPriority	1.3.6.1.4.1.351.140.1.2.1.1.1.35	Integer32	read-create	This object is the routing priority to be assigned to connections which enter the network from this ingress interface, but does not carry the routing priority signaling in the SETUP message. SETUP message. A default routing priority of 8 is used if this object is not configured. A routing priority 1 is the highest priority for a user connection. A connection tagged with a routing priority of 1 is derouted ahead of connections tagged with other priority values.
I32 cwspRoutingVci	1.3.6.1.4.1.351.140.1.2.1.1.1.12	Integer32	read-create	Indicates the VCI used for the PNNI lowest level RCC, acceptable value is 32-65535, and 18 being the default.
I32 cwspRoutingVpi	1.3.6.1.4.1.351.140.1.2.1.1.1.11	Integer32	read-create	Indicates the VPI used for PNNI lowest level RCC.
C32 cwspSetupRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.5	Counter32	read-only	Number of SETUP messages received on this interface.
C32 cwspSetupXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.27	Counter32	read-only	Number of SETUP messages transmitted from this interface.
INT cwspSide	1.3.6.1.4.1.351.140.1.2.1.1.1.18	INTEGER	read-create	This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2).
I32 cwspSigCfgT301	1.3.6.1.4.1.351.140.1.2.3.1.1.1	Integer32	read-write	Timer started when ALERT message received at Call Received State. Normally, timer is stopped when CONNECT message is received. Clear call at first expiry.
I32 cwspSigCfgT303	1.3.6.1.4.1.351.140.1.2.3.1.1.2	Integer32	read-write	Timer started when SETUP message sent at Call Present State. Normally, timer is stopped when ALERT, CONNECT, RELEASE COMPLETE or CALL PROCEEDING message is received. Resend SETUP message and restart the timer at first expiry; Clear network connection and enter NULL state at second expiry.
I32 cwspSigCfgT308	1.3.6.1.4.1.351.140.1.2.3.1.1.3	Integer32	read-write	Timer started when RELEASE message sent at Release Indication State. Normally, timer is stopped when RELEASE COMPLETE or RELEASE message is received. Resend RELEASE and restart the timer at first expiry; Release call reference and enter NULL state at second expiry.
I32 cwspSigCfgT310	1.3.6.1.4.1.351.140.1.2.3.1.1.4	Integer32	read-write	Timer started when CALL PROCEEDING message received at Incoming Call Proceeding State. Normally, timer is stopped when ALERT, CONNECT or RELEASE message is received. Clear call at first expiry. Range from 10 to 20 seconds for UNI 3.0/3.1 with default of 10; 30 to 120 seconds for UNI 4.0 with default of 30, default number can be 10 or 30, 10 is used.
I32 cwspSigCfgT316	1.3.6.1.4.1.351.140.1.2.3.1.1.5	Integer32	read-write	Timer started when RESTART message sent Restart Request State. Normally, timer is stopped when RESTART ACK message is received. RESTART may be sent multiple times in both first or second expiry.
I32 cwspSigCfgT317	1.3.6.1.4.1.351.140.1.2.3.1.1.6	Integer32	read-write	Timer started when RESTART message received at Restart State. Normally, timer is stopped when Internal clearing of call references happen. Maintenance notification at first expiry. The value of this timer should be less than T316.
I32 cwspSigCfgT322	1.3.6.1.4.1.351.140.1.2.3.1.1.7	Integer32	read-write	Timer started when STATUS ENQUIRY message sent at any call state. Normally, timer is stopped when STATUS RELEASE or RELEASE COMPLETE message is received. STATUS ENQUIREY message may be resent several times in both first or second expiry.
I32 cwspSigCfgT397	1.3.6.1.4.1.351.140.1.2.3.1.1.8	Integer32	read-write	Timer started when ALERTING or PARTY ALERTING message received in point-to-multipoint call. Normally timer is stopped when ADD PARTY ACK message is received. Clear party at first expiry.
I32 cwspSigCfgT398	1.3.6.1.4.1.351.140.1.2.3.1.1.9	Integer32	read-write	Timer is started when DROP PARTY message sent at Drop Party Initiated State. Normally, timer is stopped when DROP PARTY ACK or RELEASE message is received. Send DROP PARTY ACK or RELEASE at first expiry.
I32 cwspSigCfgT399	1.3.6.1.4.1.351.140.1.2.3.1.1.10	Integer32	read-write	Timer is started when ADD PARTY message sent at Add Party Initiated State. Normally, timer is stopped when ADD PARTY ACK, ADD PARTY REJ or RELEASE message is received. Clear the party and enter NULL Party State at first expiry. Range from 14 to 28 seconds for UNI 3.0/3.1 with default of 14; 34 to 124 seconds for UNI 4.0 with default of 34, default can be 14 or 34, 14 is used.
cwspSigConfig	1.3.6.1.4.1.351.140.1.2.3
cwspSigConfigEntry	1.3.6.1.4.1.351.140.1.2.3.1.1		not-accessible	An entry in the signaling configuration table. Each entry indexed by the ifIndex of a port.
cwspSigConfigGrp	1.3.6.1.4.1.351.140.3.2.11			A collection of objects providing information about signaling configuration and associated parameters.
cwspSigConfigTable	1.3.6.1.4.1.351.140.1.2.3.1		not-accessible	This table specifies signaling configuration parameters.
INT cwspSigCounterReset	1.3.6.1.4.1.351.140.1.2.6.1.1.1	INTEGER	read-write	Writing a 2 to this object resets the all Sig counters.
I32 cwspSignallingVci	1.3.6.1.4.1.351.140.1.2.1.1.1.10	Integer32	read-create	Indicates the signaling VCI used on the interface, acceptable value is 32-65535, and 5 being the default.
I32 cwspSignallingVpi	1.3.6.1.4.1.351.140.1.2.1.1.1.9	Integer32	read-create	Denotes the Signaling VPI used on the interface.
cwspSigStats	1.3.6.1.4.1.351.140.1.2.6
cwspSigStatsEntry	1.3.6.1.4.1.351.140.1.2.6.1.1		not-accessible	An entry contains signaling statistics.
cwspSigStatsGrp	1.3.6.1.4.1.351.140.3.2.5			A collection of objects providing information about signaling statistics.
cwspSigStatsTable	1.3.6.1.4.1.351.140.1.2.6.1		not-accessible	This table contains signaling statistics counters
ADR cwspSpvcAddress	1.3.6.1.4.1.351.140.1.2.1.1.1.36	CiscoWanNsapAtmAddress	read-only	This object identifies the internal NSAP assigned to a port by the switch. a) The format is that of 13-byte node prefix and 7-byte port number. b) When the switch's node prefix is modified, the node prefix part of this variable is also changed accordingly. Note: the switch's node prefix cannot be changed if there are connections on the switch. c) The port number can be physical port identifier or the ifIndex of this port.
T/F cwspSpvcBlocked	1.3.6.1.4.1.351.140.1.2.1.1.1.4	TruthValue	read-create	Indicates whether soft permanent virtual connections are allowed through this interface.
cwspSpvcGrp	1.3.6.1.4.1.351.140.3.2.18			A collection of objects providing spvc related information in pnni controller.
OCT cwspSpvcNodePrefix	1.3.6.1.4.1.351.140.1.4.2	OCTET STRING	read-write	Spvc node prefix for the pnni controller. This node prefix identifies an SPVC node in the network.
C32 cwspSscopBgakRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.4	Counter32	read-only	This object stores the number of SSCOP BGN ACK PDUs received at this interface.
C32 cwspSscopBgakXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.19	Counter32	read-only	This object stores the number of SSCOP BGN ACK PDUs transmitted on this interface.
C32 cwspSscopBgnRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.3	Counter32	read-only	This object stores the number of SSCOP BGN PDUs received at this interface.
C32 cwspSscopBgnXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.18	Counter32	read-only	This object stores the number of SSCOP BGN PDUs transmitted over this interface.
C32 cwspSscopBgrejRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.9	Counter32	read-only	This object stores the number of SSCOP BGN REJ PDUs received at this interface.
C32 cwspSscopBgrejXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.24	Counter32	read-only	This object stores the number of SSCOP BGN REJ PDUs transmitted over this interface.
cwspSscopConfig	1.3.6.1.4.1.351.140.1.2.4
cwspSscopConfigGrp	1.3.6.1.4.1.351.140.3.2.12			A collection of objects providing information about SSCOP configuration and associated parameters.
INT cwspSscopCounterReset	1.3.6.1.4.1.351.140.1.2.7.1.1.1	INTEGER	read-write	This object specifies whether the SSCOP statistics collected for this interface needs to be reset.
C32 cwspSscopEndakRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.6	Counter32	read-only	This object stores the number of SSCOP END ACK PDUs received at this interface.
C32 cwspSscopEndakXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.21	Counter32	read-only	This object stores the number of SSCOP END ACK PDUs transmitted on this interface.
C32 cwspSscopEndRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.5	Counter32	read-only	This object stores the number of SSCOP END PDUs received at this interface.
C32 cwspSscopEndXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.20	Counter32	read-only	This object stores the number of SSCOP END PDUs transmitted on this interface.
cwspSscopEntry	1.3.6.1.4.1.351.140.1.2.4.1.1		not-accessible	An entry in the SSCOP configuration table. Each entry indexed by the ifIndex of a port.
C32 cwspSscopErakRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.17	Counter32	read-only	This object stores the number of SSCOP ER ACK (error recovery ack) PDUs received at this interface.
C32 cwspSscopErakXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.32	Counter32	read-only	This object stores the number of SSCOP ER(error recovery) ACK PDUs transmitted over this interface.
C32 cwspSscopIgnoredPduRcvEx	1.3.6.1.4.1.351.140.1.2.7.1.1.2	Counter32	read-only	This object stores the number of SSCOP PDUs that are received but ignored due to incorrect size, invalid PDU, unknown PDU type.
I32 cwspSscopMaxCC	1.3.6.1.4.1.351.140.1.2.4.1.1.6	Integer32	read-write	This object contains the upper limit for the number of transmissions of a BGN, END, ER or RS PDU.
I32 cwspSscopMaxPD	1.3.6.1.4.1.351.140.1.2.4.1.1.7	Integer32	read-write	This object contains an upper limit for a counter which counts the number of SD PDUs transmitted between transmissions of POLL PDUs or the number of SD PDUs transmitted before the transmission of the first POLL PDU after POLL timer became active.
I32 cwspSscopMaxSTAT	1.3.6.1.4.1.351.140.1.2.4.1.1.8	Integer32	read-write	This object contains an upper limit for the number of list elements placed in a STAT PDU.
C32 cwspSscopMdRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.16	Counter32	read-only	This object stores the number of SSCOP MD (Management data) PDUs received at this interface.
C32 cwspSscopMdXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.31	Counter32	read-only	This object stores the number of SSCOP MD PDUs transmitted over this interface.
C32 cwspSscopPollRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.12	Counter32	read-only	This object stores the number of SSCOP POLL PDUs received at this interface.
C32 cwspSscopPollXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.27	Counter32	read-only	This object stores the number of SSCOP POLL PDUs transmitted over this interface.
C32 cwspSscopRsakRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.8	Counter32	read-only	This object stores the number of SSCOP RS(Resync) ACK PDUs received at this interface.
C32 cwspSscopRsakXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.23	Counter32	read-only	This object stores the number of SSCOP RS (Resync) ACK PDUs transmitted over this interface.
C32 cwspSscopRsRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.7	Counter32	read-only	This object stores the number of SSCOP RS(Resync) PDUs received at this interface.
C32 cwspSscopRsXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.22	Counter32	read-only	This object stores the number of SSCOP RS (Resync) PDUs transmitted over this interface.
C32 cwspSscopSdpRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.11	Counter32	read-only	This object stores the number of SSCOP SDP (Sequenced Data with Poll) PDUs received at this interface.
C32 cwspSscopSdpXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.26	Counter32	read-only	This object stores the number of SSCOP SDP PDUs transmitted over this interface.
C32 cwspSscopSdRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.10	Counter32	read-only	This object stores the number of SSCOP SD (Sequenced Data) PDUs received at this interface.
C32 cwspSscopSdXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.25	Counter32	read-only	This object stores the number of SSCOP SD transmitted over this interface.
C32 cwspSscopStatRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.13	Counter32	read-only	This object stores the number of SSCOP STAT PDUs received at this interface.
cwspSscopStats	1.3.6.1.4.1.351.140.1.2.7
cwspSscopStatsEntry	1.3.6.1.4.1.351.140.1.2.7.1.1		not-accessible	An entry contains SSCOP (Layer 2) statistics.
cwspSscopStatsGrp	1.3.6.1.4.1.351.140.3.2.13			A collection of objects providing information about SSCOP statistics.
cwspSscopStatsTable	1.3.6.1.4.1.351.140.1.2.7.1		not-accessible	This table contains SSCOP (Layer 2) statistics counters.
INT cwspSscopStatus	1.3.6.1.4.1.351.140.1.2.6.1.1.42	INTEGER	read-only	Sscop link status on an NNI interface, object is meaningful along with ciscoWANSscopLinkChange trap.
C32 cwspSscopStatXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.28	Counter32	read-only	This object stores the number of SSCOP STAT PDUs transmitted over this interface.
cwspSscopTable	1.3.6.1.4.1.351.140.1.2.4.1		not-accessible	This table specifies SSCOP (Layer 2) configuration parameters.
I32 cwspSscopTmrCC	1.3.6.1.4.1.351.140.1.2.4.1.1.1	Integer32	read-write	This object contains the value for Connection control timer.
I32 cwspSscopTmrKeepAlive	1.3.6.1.4.1.351.140.1.2.4.1.1.2	Integer32	read-write	This object contains the value for keep alive timer
I32 cwspSscopTmrNoResp	1.3.6.1.4.1.351.140.1.2.4.1.1.3	Integer32	read-write	This object contains the value for no response timer.
I32 cwspSscopTmrPoll	1.3.6.1.4.1.351.140.1.2.4.1.1.4	Integer32	read-write	This object contains the value for poll timer.
I32 cwspSscopTmtIdle	1.3.6.1.4.1.351.140.1.2.4.1.1.5	Integer32	read-write	This object contains the value for idle timer.
C32 cwspSscopUdRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.15	Counter32	read-only	This object stores the number of SSCOP UD (Unit data) PDUs received at this interface.
C32 cwspSscopUdXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.30	Counter32	read-only	This object stores the number of SSCOP UD PDUs transmitted over this interface.
C32 cwspSscopUstatRcv	1.3.6.1.4.1.351.140.1.2.7.1.1.14	Counter32	read-only	This object stores the number of SSCOP USTAT (Unsolicited STAT) PDUs received at this interface.
C32 cwspSscopUstatXmt	1.3.6.1.4.1.351.140.1.2.7.1.1.29	Counter32	read-only	This object stores the number of SSCOP USTAT PDUs transmitted over this interface.
C32 cwspStatusEnqRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.11	Counter32	read-only	Number of STATUS ENQUIRY messages received on this interface.
C32 cwspStatusEnqXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.33	Counter32	read-only	Number of STATUS ENQUIRY messages transmitted from this interface.
C32 cwspStatusRcv	1.3.6.1.4.1.351.140.1.2.6.1.1.10	Counter32	read-only	Number of STATUS messages received on this interface.
C32 cwspStatusXmt	1.3.6.1.4.1.351.140.1.2.6.1.1.32	Counter32	read-only	Number of STATUS messages transmitted from this interface.
T/F cwspSvcBlocked	1.3.6.1.4.1.351.140.1.2.1.1.1.3	TruthValue	read-create	Indicates whether Switches virtual connections are allowed through this interface.
C32 cwspTimerExpiries	1.3.6.1.4.1.351.140.1.2.6.1.1.21	Counter32	read-only	Number of timeouts occurred on this interface.
INT cwspUniType	1.3.6.1.4.1.351.140.1.2.1.1.1.17	INTEGER	read-create	The type of the ATM device, either public or private.
INT cwspUniVersion	1.3.6.1.4.1.351.140.1.2.1.1.1.15	INTEGER	read-create	An indication of the latest version of the ATM Forum UNI Signaling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. The value of 'self(9)' indicates this entry is a voice port. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed.
I32 cwspUtilFactorAbr	1.3.6.1.4.1.351.140.1.2.2.1.1.4	Integer32	read-write	This is the booking factor for ABR service
I32 cwspUtilFactorCbr	1.3.6.1.4.1.351.140.1.2.2.1.1.1	Integer32	read-write	This is the booking factor for CBR service.
I32 cwspUtilFactorNrtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.3	Integer32	read-write	This is the booking factor for non-real time VBR service
I32 cwspUtilFactorRtVbr	1.3.6.1.4.1.351.140.1.2.2.1.1.2	Integer32	read-write	This is the booking factor for real time VBR service
I32 cwspUtilFactorUbr	1.3.6.1.4.1.351.140.1.2.2.1.1.5	Integer32	read-write	This is the booking factor for UBR service.
STR cwsSwRevision	1.3.6.1.4.1.351.140.1.1.1	DisplayString	read-only	PNNI network controller software revision number.

RFC description

Cisco vendor-private MIB for ATM service management on BPX-SES and MGX switches, supporting SVC (Switched Virtual Circuit) provisioning and configuration.

Start monitoring Cisco BPX-SES/MGX ATM switch (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-WAN-SVC-MIB