All MIBs › IPAD-ATM-MIB
Organization: Verilink Corporation
Last Updated: 2000-03-27
Category: ATM, Protocol: ATM, Vendor: ARRIS, Vendor: Verilink
Description: Verilink IPAD ATM MIB providing SNMP objects for ATM interface configuration and cell-layer statistics on IPAD access devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is IPAD-ATM-MIB?
IPAD-ATM-MIB is a Verilink-specific MIB for the IPAD family of ATM access/multiplexer devices, covering ATM interface configuration and cell-layer statistics. It exposes data organized around per-interface ATM parameters, virtual circuit connection (VCC) counters, and bandwidth allocation settings. For monitoring device health it is used to track ATM interface operational status, alarm conditions, and connection-establishment success versus failure counts, which reveal link or provisioning problems. It builds on standard ATM/interface concepts but is a proprietary enterprise MIB rather than one that formally imports a common IETF ATM MIB. It is typically deployed on WAN access multiplexers or ATM edge devices in carrier or enterprise access networks, where IPAD-ATM-MIB SNMP monitoring tracks interface status and VCC connection health.
IPNetwork Monitor allows you to monitor SNMP objects defined in IPAD-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Verilink IPAD ATM access multiplexer
Monitoring Examples
A monitoring system would poll ipadAtmTable/ipadAtmTableEntry (keyed by ipadAtmIfIndex) to check ipadAtmOperStatus, and compare ipadAtmVccsOpenedOK against ipadAtmVccsNotOpened to detect a rising failure rate in VCC setup. Bandwidth objects such as ipadAtmLineBandwidth, ipadAtmAAL5Bandwidth, and ipadAtmOverSubscriptionFactor let an operator confirm the link isn't oversubscribed beyond ipadAtmOverSubBandwidth. ipadAtmAlarmReset can be invoked to clear a latched alarm once the underlying condition is resolved.
What Can Be Monitored
- ATM interface operational status
- VCC open success/failure counts
- line and AAL5 bandwidth
- oversubscription factor
- alarm state
This MIB depends on
Related MIBs
Imported Objects
From IPADv2-MIB
| ipad | MODULE-IDENTITY |
From SNMPv2-SMI
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks |
From SNMPv2-TC
| DisplayString |
How to Use in IPNetwork Monitor
Example using ipadAtmOperStatus OID:
Select a Verilink IPAD ATM access multiplexer as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ipadAtmOperStatus into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The up/down status of this atm interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value is anything other than 'upCellSync', since that indicates the condition this object reports has changed to one worth investigating. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ipadAtm | 1.3.6.1.4.1.321.100.1.25 | The IPAD ATM MIB. | ||
| ipadAtmParms | 1.3.6.1.4.1.321.100.1.25.1 | |||
| ipadAtmTable | 1.3.6.1.4.1.321.100.1.25.1.1 | not-accessible | Table of ATM parameters. | |
| ipadAtmTableEntry | 1.3.6.1.4.1.321.100.1.25.1.1.1 | not-accessible | An entry in the ipad ATM parameter table. | |
| INT ipadAtmIfIndex | 1.3.6.1.4.1.321.100.1.25.1.1.1.1 | INTEGER | read-only | The index into the ATM table. |
| INT ipadAtmOperStatusEx | 1.3.6.1.4.1.321.100.1.25.1.1.1.2 | INTEGER | read-only | The up/down status of this atm interface. |
| INT ipadAtmVccsOpenedOK | 1.3.6.1.4.1.321.100.1.25.1.1.1.3 | INTEGER | read-only | The current number of successfully opened VCCs on this ATM interface. |
| INT ipadAtmVccsNotOpened | 1.3.6.1.4.1.321.100.1.25.1.1.1.4 | INTEGER | read-only | The current number of VCCs that were not successfully opened on this ATM interface. |
| INT ipadAtmAlarmReset | 1.3.6.1.4.1.321.100.1.25.1.1.1.5 | INTEGER | read-write | Reset the alarms or statistics of this ATM interface. |
| INT ipadAtmOverSubscriptionFactor | 1.3.6.1.4.1.321.100.1.25.1.1.1.6 | INTEGER | read-write | The current over-subscription-factor for this ATM interface. Used for VBR and UBR VC connection admission control to allow the either VBR or UBR service category connections to collectively use more bandwidth than is available in order to make use of the statistical multiplexing of the connections. The PCR of each individual VC is limited to the interface's line rate. However when multiple VCs are configured, the sum of their PCR values can go up to (OverSubscriptionFactor * (line-rate) / 53*8). A value of 1 indicates no oversubscription allowed. A value of 5 indicates 5 times oversubscription allowed. Note that CBR connections cannot be oversubscribed. Also, if CES is in use on the interface, all AAL5 connections have their PCR limited to the amount which the line rate can support above the commitment for CES, and the oversubscription applies only to that bandwidth above the CES commitment. |
| INT ipadAtmLineBandwidth | 1.3.6.1.4.1.321.100.1.25.1.1.1.7 | INTEGER | read-only | The current ATM Line interface Bandwidth in cells per second. |
| INT ipadAtmAAL5Bandwidth | 1.3.6.1.4.1.321.100.1.25.1.1.1.8 | INTEGER | read-only | The current AAL5 Bandwidth in cells per second. |
| INT ipadAtmOverSubBandwidth | 1.3.6.1.4.1.321.100.1.25.1.1.1.9 | INTEGER | read-only | The AAL5 Oversubscription Bandwidth in cells per second. This value is ipadAtmAAL5Bandwidth multiplied by the ipadAtmOversubscriptionFactor. |
| INT ipadAtmCbrUsedBandwidth | 1.3.6.1.4.1.321.100.1.25.1.1.1.10 | INTEGER | read-only | The amount of AAL5 Bandwidth allocated to CBR VCs in cells per second. |
| INT ipadAtmVbrUsedBandwidth | 1.3.6.1.4.1.321.100.1.25.1.1.1.11 | INTEGER | read-only | The amount of AAL5 Bandwidth allocated to VBR VCs in cells per second. When OversubscriptionFactor is greater than 1, this value can exceed ipadAtmAAL5Bandwidth. |
| INT ipadAtmUbrUsedBandwidth | 1.3.6.1.4.1.321.100.1.25.1.1.1.12 | INTEGER | read-only | The amount of AAL5 Bandwidth allocated to UBR VCs in cells per second. When OversubscriptionFactor is greater than 1, this value can exceed ipadAtmAAL5Bandwidth. |
| INT ipadAtmQos0Pcr | 1.3.6.1.4.1.321.100.1.25.1.1.1.13 | INTEGER | read-only | The value of PCR to be used for each VC which has no specified QOS profile (0). The VC is configured as UBR with the given Peak Cell Rate. |
| ipadAtmStatsParms | 1.3.6.1.4.1.321.100.1.25.2 | |||
| ipadAtmStatsTable | 1.3.6.1.4.1.321.100.1.25.2.1 | not-accessible | Table of ATM statistics. | |
| ipadAtmStatsTableEntry | 1.3.6.1.4.1.321.100.1.25.2.1.1 | not-accessible | An entry in the ipad ATM Stats parameter table. | |
| INT ipadAtmStatsIndex | 1.3.6.1.4.1.321.100.1.25.2.1.1.1 | INTEGER | read-only | The index representing the ATM interface. |
| INT ipadAtmStatsPeriodIndex | 1.3.6.1.4.1.321.100.1.25.2.1.1.2 | INTEGER | read-only | The index representing the period for the ATM stats entry. |
| TIK ipadAtmStatsTimeStamp | 1.3.6.1.4.1.321.100.1.25.2.1.1.3 | TimeTicks | read-only | The value of sysUpTime the last time the statistics were updated. |
| INT ipadAtmStatsRxFramesOK | 1.3.6.1.4.1.321.100.1.25.2.1.1.4 | INTEGER | read-only | The number of error-free frames received during the period. |
| INT ipadAtmStatsTxFramesOK | 1.3.6.1.4.1.321.100.1.25.2.1.1.5 | INTEGER | read-only | The number of frames successfully transmitted during the period. |
| INT ipadAtmStatsRxFramesError | 1.3.6.1.4.1.321.100.1.25.2.1.1.6 | INTEGER | read-only | The number of errored frames received during the period. |
| INT ipadAtmStatsTxFramesError | 1.3.6.1.4.1.321.100.1.25.2.1.1.7 | INTEGER | read-only | The number of transmitted frames that were errored. |
| INT ipadAtmStatsRxBytesOK | 1.3.6.1.4.1.321.100.1.25.2.1.1.8 | INTEGER | read-only | The number of error-free bytes received during the period. |
| INT ipadAtmStatsTxBytesOK | 1.3.6.1.4.1.321.100.1.25.2.1.1.9 | INTEGER | read-only | The number of successfully transmitted bytes during the period. |
| INT ipadAtmStatsLostSync | 1.3.6.1.4.1.321.100.1.25.2.1.1.10 | INTEGER | read-only | The number of times sync has been lost or recovered. |
| INT ipadAtmStatsOamCellsRx | 1.3.6.1.4.1.321.100.1.25.2.1.1.11 | INTEGER | read-only | The number of OAM cells received on this ATM link. |
| INT ipadAtmStatsOamCellsTx | 1.3.6.1.4.1.321.100.1.25.2.1.1.12 | INTEGER | read-only | The number of OAM cells transmitted on this ATM link. |
| ipadAtmVccParms | 1.3.6.1.4.1.321.100.1.25.3 | |||
| ipadAtmVccTable | 1.3.6.1.4.1.321.100.1.25.3.1 | not-accessible | Table of Virtual Channel parameters. | |
| ipadAtmVccTableEntry | 1.3.6.1.4.1.321.100.1.25.3.1.1 | not-accessible | An entry in the ipad ATM Vcc parameter table. | |
| INT ipadAtmVccIndex | 1.3.6.1.4.1.321.100.1.25.3.1.1.1 | INTEGER | read-only | The index into the ATM VCC table, corresponding to ifIndex. |
| INT ipadAtmVccVpiIndex | 1.3.6.1.4.1.321.100.1.25.3.1.1.2 | INTEGER | read-only | The VPI for the VCC. |
| INT ipadAtmVccVciIndex | 1.3.6.1.4.1.321.100.1.25.3.1.1.3 | INTEGER | read-only | The VCI for the VCC. |
| INT ipadAtmVccEncapsulationType | 1.3.6.1.4.1.321.100.1.25.3.1.1.4 | INTEGER | read-write | The encapsulation method used on this VCC. vcMux indicates null encapsulation and may be used for IP routing or PPP applications. llcMux indicates LLC encapsulation and may be used for IP routing, bridging, and PPP applications. serialPPPoA and serialHDLCoA indicate serial port applications. |
| INT ipadAtmVccTrafficType | 1.3.6.1.4.1.321.100.1.25.3.1.1.5 | INTEGER | read-only | The traffic type of this VCC. |
| INT ipadAtmVccChannelRate | 1.3.6.1.4.1.321.100.1.25.3.1.1.6 | INTEGER | read-only | The channel rate for this VCC. |
| INT ipadAtmVccAlarmReset | 1.3.6.1.4.1.321.100.1.25.3.1.1.7 | INTEGER | read-write | Reset the alarms or statistics of this VCC. |
| INT ipadAtmVccSLATimer | 1.3.6.1.4.1.321.100.1.25.3.1.1.8 | INTEGER | read-write | The time in seconds between SLA measurement packets being sent. |
| INT ipadAtmVccRemoteFramesOffered | 1.3.6.1.4.1.321.100.1.25.3.1.1.9 | INTEGER | read-only | The number of frames offered by the remote device. |
| INT ipadAtmVccFramesReceived | 1.3.6.1.4.1.321.100.1.25.3.1.1.10 | INTEGER | read-only | The number of frames received by this device. |
| INT ipadAtmVccRemoteDataOffered | 1.3.6.1.4.1.321.100.1.25.3.1.1.11 | INTEGER | read-only | The number of data bytes offered by the remote device. |
| INT ipadAtmVccDataReceived | 1.3.6.1.4.1.321.100.1.25.3.1.1.12 | INTEGER | read-only | The number of data bytes received by this device. |
| INT ipadAtmVccRemoteActive | 1.3.6.1.4.1.321.100.1.25.3.1.1.13 | INTEGER | read-only | The current state of the remote device as detected by the local device. |
| INT ipadAtmVccRemoteVpi | 1.3.6.1.4.1.321.100.1.25.3.1.1.14 | INTEGER | read-only | The remote VPI. |
| INT ipadAtmVccRemoteVci | 1.3.6.1.4.1.321.100.1.25.3.1.1.15 | INTEGER | read-only | The remote VCI. |
| IP ipadAtmVccRemoteIPAddress | 1.3.6.1.4.1.321.100.1.25.3.1.1.16 | IpAddress | read-only | The IP Address of the device connected to the remote end of this VCC. |
| STR ipadAtmVccRemoteUnitId | 1.3.6.1.4.1.321.100.1.25.3.1.1.17 | DisplayString | read-only | The Unit ID assigned to the devie connected to the remote end of this VCC. |
| INT ipadAtmVccEtoeLoopbackCommand | 1.3.6.1.4.1.321.100.1.25.3.1.1.18 | INTEGER | read-write | A command to issue on the VCC Loopback. The start command is used to start an OAM F5 VCC loopback. The stop command is used to terminate the OAM loopback. The statistics variables associated with the OAM loopback are automatically cleared when a loopback is started. |
| INT ipadAtmVccEtoeLoopbackState | 1.3.6.1.4.1.321.100.1.25.3.1.1.19 | INTEGER | read-only | The state of this VCC loopback function. The active state means OAM F5 loopback cells are being sent from this endpoint once every 5 seconds. The loopback state means that OAM F5 loopback cells are being received and returned from this endpoint. |
| INT ipadAtmVccEtoeLoopbackCellsTx | 1.3.6.1.4.1.321.100.1.25.3.1.1.20 | INTEGER | read-only | The number of OAM F5 Loopback cells transmitted for this VCC. |
| INT ipadAtmVccEtoeLoopbackCellsRx | 1.3.6.1.4.1.321.100.1.25.3.1.1.21 | INTEGER | read-only | The number of OAM F5 Loopback cells received for this VCC. |
| INT ipadAtmVccEtoeLoopbackRttMin | 1.3.6.1.4.1.321.100.1.25.3.1.1.22 | INTEGER | read-only | The minimum round trip time in milliseconds between sending a loopback cell and receiving the returned loopback cell. |
| INT ipadAtmVccEtoeLoopbackRttMax | 1.3.6.1.4.1.321.100.1.25.3.1.1.23 | INTEGER | read-only | The maximum round trip time in milliseconds between sending a loopback cell and receiving the returned loopback cell. |
| INT ipadAtmVccEtoeLoopbackRttAvg | 1.3.6.1.4.1.321.100.1.25.3.1.1.24 | INTEGER | read-only | The average round trip time in milliseconds between sending a loopback cell and receiving the returned loopback cell. |
| INT ipadAtmVccSegLoopbackCommand | 1.3.6.1.4.1.321.100.1.25.3.1.1.25 | INTEGER | read-write | A command to issue on the VCC Loopback. The start command is used to start an OAM F5 VCC loopback. The stop command is used to terminate the OAM loopback. The statistics variables associated with the OAM loopback are automatically cleared when a loopback is started. |
| INT ipadAtmVccSegLoopbackState | 1.3.6.1.4.1.321.100.1.25.3.1.1.26 | INTEGER | read-only | The state of this VCC loopback function. The active state means OAM F5 loopback cells are being sent from this endpoint once every 5 seconds. The loopback state means that OAM F5 loopback cells are being received and returned from this endpoint. |
| INT ipadAtmVccSegLoopbackCellsTx | 1.3.6.1.4.1.321.100.1.25.3.1.1.27 | INTEGER | read-only | The number of OAM F5 Loopback cells transmitted for this VCC. |
| INT ipadAtmVccSegLoopbackCellsRx | 1.3.6.1.4.1.321.100.1.25.3.1.1.28 | INTEGER | read-only | The number of OAM F5 Loopback cells received for this VCC. |
| INT ipadAtmVccSegLoopbackRttMin | 1.3.6.1.4.1.321.100.1.25.3.1.1.29 | INTEGER | read-only | The minimum round trip time in milliseconds between sending a loopback cell and receiving the returned loopback cell. |
| INT ipadAtmVccSegLoopbackRttMax | 1.3.6.1.4.1.321.100.1.25.3.1.1.30 | INTEGER | read-only | The maximum round trip time in milliseconds between sending a loopback cell and receiving the returned loopback cell. |
| INT ipadAtmVccSegLoopbackRttAvg | 1.3.6.1.4.1.321.100.1.25.3.1.1.31 | INTEGER | read-only | The average round trip time in milliseconds between sending a loopback cell and receiving the returned loopback cell. |
| INT ipadAtmVccEtoeContCheckCommand | 1.3.6.1.4.1.321.100.1.25.3.1.1.32 | INTEGER | read-write | ipadAtmVccEtoeContCheckCommand is used to request activation or deactivation of the End-to-End continuity check on this VCC. |
| INT ipadAtmVccEtoeContCheckAutoActivate | 1.3.6.1.4.1.321.100.1.25.3.1.1.33 | INTEGER | read-write | ipadAtmVccEtoeContCheckAutoActivate indicates whether End-to-End continuity check is automatically activated on this VCC. A Value of disable means CC is not automatically activated. A value of enable permits CC to be automatically activated after the VCC connection is established. |
| INT ipadAtmVccEtoeContCheckType | 1.3.6.1.4.1.321.100.1.25.3.1.1.34 | INTEGER | read-only | Default Continuity Check Type used for this VCC. A value of none selects no continuity check. A value of sink, source, or sinkAndSource selects the respective continuity check functions. ipadAtmVccEtoeContCheckType can only be changed when CC is not currently active. |
| INT ipadAtmVccEtoeContCheckTypeInUse | 1.3.6.1.4.1.321.100.1.25.3.1.1.35 | INTEGER | read-only | The current Continuity Check Type in use for this VCC. ipadAtmVccEtoeContCheckTypeInUse may differ from ipadAtmVccEtoeContCheckType if CC is activated via inband OAM. |
| INT ipadAtmVccEtoeContCheckStatus | 1.3.6.1.4.1.321.100.1.25.3.1.1.36 | INTEGER | read-only | The current state of Continuity Check for this VCC. In the ready state, no CC is being performed. The ready state indicates CC is permitted to be activated. The activating state indicates CC has been requested and is being activated. During activation, an OAM activation cell is sent to the opposite endpoint to request CC. Once an activation confirmed cell is received, the state is then changed to active. Reception of an activation denied response or a multiple of 3 ten-second time outs waiting for a confirmation will result in an activationFailed state. CC sourcing is performed when state is active or activating. CC sinking is performed when state is active. |
| INT ipadAtmVccEtoeContCheckCellsTx | 1.3.6.1.4.1.321.100.1.25.3.1.1.37 | INTEGER | read-only | The number of CC cells transmitted for this VCC for CC Sourcing function. |
| INT ipadAtmVccEtoeContCheckCellsRx | 1.3.6.1.4.1.321.100.1.25.3.1.1.38 | INTEGER | read-only | The number of CC cells received for this VCC for the CC Sinking function. |
| INT ipadAtmVccEtoeAisStatus | 1.3.6.1.4.1.321.100.1.25.3.1.1.39 | INTEGER | read-only | The current e-t-e_VC-AIS state. |
| INT ipadAtmVccEtoeRdiStatus | 1.3.6.1.4.1.321.100.1.25.3.1.1.40 | INTEGER | read-only | The current e-t-e_VC-RDI state. |
| ipadAtmVccStatsParms | 1.3.6.1.4.1.321.100.1.25.4 | |||
| ipadAtmVccStatsTable | 1.3.6.1.4.1.321.100.1.25.4.1 | not-accessible | Table of ATM statistics. | |
| ipadAtmVccStatsTableEntry | 1.3.6.1.4.1.321.100.1.25.4.1.1 | not-accessible | An entry in the ipad ATM VccStats parameter table. | |
| INT ipadAtmVccStatsIndex | 1.3.6.1.4.1.321.100.1.25.4.1.1.1 | INTEGER | read-only | The index representing the ATM interface. |
| INT ipadAtmVccStatsVpiIndex | 1.3.6.1.4.1.321.100.1.25.4.1.1.2 | INTEGER | read-only | The index representing the VPI of the VCC. |
| INT ipadAtmVccStatsVciIndex | 1.3.6.1.4.1.321.100.1.25.4.1.1.3 | INTEGER | read-only | The index representing the VCI of the VCC. |
| INT ipadAtmVccStatsPeriodIndex | 1.3.6.1.4.1.321.100.1.25.4.1.1.4 | INTEGER | read-only | The index representing the period for the VCC stats entry. |
| TIK ipadAtmVccStatsTimeStamp | 1.3.6.1.4.1.321.100.1.25.4.1.1.5 | TimeTicks | read-only | The value of sysUpTime the last time the statistics were updated. |
| INT ipadAtmVccStatsRxFramesOK | 1.3.6.1.4.1.321.100.1.25.4.1.1.6 | INTEGER | read-only | The number of error-free frames received this period. |
| INT ipadAtmVccStatsTxFramesOK | 1.3.6.1.4.1.321.100.1.25.4.1.1.7 | INTEGER | read-only | The number of frames successfully transmitted during this period. |
| INT ipadAtmVccStatsRxFramesError | 1.3.6.1.4.1.321.100.1.25.4.1.1.8 | INTEGER | read-only | The number of errored frames received this period. |
| INT ipadAtmVccStatsTxFramesError | 1.3.6.1.4.1.321.100.1.25.4.1.1.9 | INTEGER | read-only | The number of frames that were not successfully transmitted during this period. |
| INT ipadAtmVccStatsRxFramesCLP | 1.3.6.1.4.1.321.100.1.25.4.1.1.10 | INTEGER | read-only | The number of frames received with CLP set during the period. |
| INT ipadAtmVccStatsRxFramesCI | 1.3.6.1.4.1.321.100.1.25.4.1.1.11 | INTEGER | read-only | The number of frames received with congestion set during the period. |
| INT ipadAtmVccStatsRxFramesAbort | 1.3.6.1.4.1.321.100.1.25.4.1.1.12 | INTEGER | read-only | The number of frames whose reception was aborted during the period. |
| INT ipadAtmVccStatsRxFramesLenViolation | 1.3.6.1.4.1.321.100.1.25.4.1.1.13 | INTEGER | read-only | The number of frames received with a length violation during the period. |
| INT ipadAtmVccStatsRxFramesCRCError | 1.3.6.1.4.1.321.100.1.25.4.1.1.14 | INTEGER | read-only | The number of frames received with CRC errors during the period. |
| INT ipadAtmVccStatsRxFramesTimeout | 1.3.6.1.4.1.321.100.1.25.4.1.1.15 | INTEGER | read-only | The number of frames whose reception timed out during the period. |
| INT ipadAtmVccStatsRxFramesHCSError | 1.3.6.1.4.1.321.100.1.25.4.1.1.16 | INTEGER | read-only | The number of frames received with an HCS error in a cell. |
| INT ipadAtmVccStatsRxFramesNoBuffer | 1.3.6.1.4.1.321.100.1.25.4.1.1.17 | INTEGER | read-only | The number of frames discarded due to the lack of buffers. |
| INT ipadAtmVccStatsRxCellsOK | 1.3.6.1.4.1.321.100.1.25.4.1.1.18 | INTEGER | read-only | The number of cells successfully received. |
| INT ipadAtmVccStatsTxCellsOK | 1.3.6.1.4.1.321.100.1.25.4.1.1.19 | INTEGER | read-only | The number of cells successfully transmitted. |
| INT ipadAtmVccStatsRxBytesOK | 1.3.6.1.4.1.321.100.1.25.4.1.1.20 | INTEGER | read-only | The number of bytes successfully received. |
| INT ipadAtmVccStatsTxBytesOK | 1.3.6.1.4.1.321.100.1.25.4.1.1.21 | INTEGER | read-only | The number of bytes successfully transmitted. |
| INT ipadAtmVccStatsDelayPeak | 1.3.6.1.4.1.321.100.1.25.4.1.1.22 | INTEGER | read-only | The peak delay measured during this period. |
| INT ipadAtmVccStatsDelayAverage | 1.3.6.1.4.1.321.100.1.25.4.1.1.23 | INTEGER | read-only | The average delay measured during this period. |
| INT ipadAtmVccStatsRoundTripTimeouts | 1.3.6.1.4.1.321.100.1.25.4.1.1.24 | INTEGER | read-only | The number of round trip delay message timeouts measured. |
| INT ipadAtmVccStatsRemoteFramesOffered | 1.3.6.1.4.1.321.100.1.25.4.1.1.25 | INTEGER | read-only | The number of frames offered by the remote device. |
| INT ipadAtmVccStatsFramesReceived | 1.3.6.1.4.1.321.100.1.25.4.1.1.26 | INTEGER | read-only | The number of frames received by the local device. |
| STR ipadAtmVccStatsFDR | 1.3.6.1.4.1.321.100.1.25.4.1.1.27 | DisplayString | read-only | The calculated frame delivery ratio. |
| INT ipadAtmVccStatsRemoteDataOffered | 1.3.6.1.4.1.321.100.1.25.4.1.1.28 | INTEGER | read-only | The number of data bytes offered by the remote device. |
| INT ipadAtmVccStatsDataReceived | 1.3.6.1.4.1.321.100.1.25.4.1.1.29 | INTEGER | read-only | The number of data bytes received by the local device. |
| STR ipadAtmVccStatsDDR | 1.3.6.1.4.1.321.100.1.25.4.1.1.30 | DisplayString | read-only | The calculated data delivery ratio. |
| INT ipadAtmVccStatsUAS | 1.3.6.1.4.1.321.100.1.25.4.1.1.31 | INTEGER | read-only | The number of seconds which the remote device was unavailable. |
| ipadAtmCesParms | 1.3.6.1.4.1.321.100.1.25.5 | |||
| ipadAtmCesTable | 1.3.6.1.4.1.321.100.1.25.5.1 | not-accessible | Table of CES parameters. | |
| ipadAtmCesTableEntry | 1.3.6.1.4.1.321.100.1.25.5.1.1 | not-accessible | An entry in the ipad ATM CES parameter table. | |
| INT ipadAtmCesIndex | 1.3.6.1.4.1.321.100.1.25.5.1.1.1 | INTEGER | read-only | The index into the ATM CES table. |
| INT ipadAtmCesPayloadScrambling | 1.3.6.1.4.1.321.100.1.25.5.1.1.2 | INTEGER | read-write | ipadAtmCesPayloadScrambling indicates whether CES payload scrambling is enabled. |
| INT ipadAtmCesAutoChannelConfiguration | 1.3.6.1.4.1.321.100.1.25.5.1.1.3 | INTEGER | read-write | ipadAtmCesAutoChannelConfiguration indicates whether the CES channel configuration should be dynamic based on available line bandwidth. |
| ipadAtmFrParms | 1.3.6.1.4.1.321.100.1.25.6 | |||
| ipadAtmFrf5SvcTable | 1.3.6.1.4.1.321.100.1.25.6.1 | not-accessible | Table of ATM FRF5 profile parameters. | |
| ipadAtmFrf5SvcTableEntry | 1.3.6.1.4.1.321.100.1.25.6.1.1 | not-accessible | An entry in the ipad ATM FRF5 service table. | |
| INT ipadAtmFrf5SvcIfIndex | 1.3.6.1.4.1.321.100.1.25.6.1.1.1 | INTEGER | read-only | The index representing the ATM interface. |
| INT ipadAtmFrf5SvcVpiIndex | 1.3.6.1.4.1.321.100.1.25.6.1.1.2 | INTEGER | read-only | The index representing the VPI of the VCC. |
| INT ipadAtmFrf5SvcVciIndex | 1.3.6.1.4.1.321.100.1.25.6.1.1.3 | INTEGER | read-only | The index representing the VCI of the VCC. |
| INT ipadAtmFrf5SvcDeToClpMappingMode | 1.3.6.1.4.1.321.100.1.25.6.1.1.4 | INTEGER | read-write | Discard Eligibility to Cell Loss Priority mapping mode. mode1: The Discard Eligibility (DE) field in the Q.922 core frame shall be copied unchanged into the DE field in the FR-SSCS PDU header and mapped to the ATM Cell Loss Priority (CLP) of every ATM cell generated by the segmentation process of that frame. mode2Const0: The DE field in the Q.922 core frame shall be copied unchanged into the DE field in the FR-SSCS PDU header and the ATM Cell Loss Priority of every ATM cell generated by the segmentation process of that frame shall be set to the constant value 0. mode2Const1: The DE field in the Q.922 core frame shall be copied unchanged into the DE field in the FR-SSCS PDU header and the ATM Cell Loss Priority of every ATM cell generated by the segmentation process of that frame shall be set to the constant value 1. |
| INT ipadAtmFrf5SvcClpToDeMappingMode | 1.3.6.1.4.1.321.100.1.25.6.1.1.5 | INTEGER | read-write | Cell Loss Priority to Discard Eligibility mapping mode. mode1: If one or more ATM cells belonging to a frame has its CLP field set to one or if the DE field of the FR-SSCS PDU is set to one, the IWF shall set the DE field of the Q.922 core frame. mode2: No mapping is performed from the ATM layer to Q.922 core layer. The FR-SSCS PDU DE field is copied unchanged to the Q.922 core frame DE field, independent of CLP indications(s) received at the ATM layer. |
| INT ipadAtmFrf5SvcN1 | 1.3.6.1.4.1.321.100.1.25.6.1.1.6 | INTEGER | read-write | Number of keep alive requests between full status requests. |
| INT ipadAtmFrf5SvcN2 | 1.3.6.1.4.1.321.100.1.25.6.1.1.7 | INTEGER | read-write | Number of errors before alarm. |
| INT ipadAtmFrf5SvcN3 | 1.3.6.1.4.1.321.100.1.25.6.1.1.8 | INTEGER | read-write | Number of events to sample N2. |
| INT ipadAtmFrf5SvcT1 | 1.3.6.1.4.1.321.100.1.25.6.1.1.9 | INTEGER | read-write | Delay before issuing a poll sequence. |
| INT ipadAtmFrf5SvcT2 | 1.3.6.1.4.1.321.100.1.25.6.1.1.10 | INTEGER | read-write | T2 timer |
| INT ipadAtmFrf5SvcActive | 1.3.6.1.4.1.321.100.1.25.6.1.1.11 | INTEGER | read-only | Specifies if the frf5 service is active. |
| INT ipadAtmFrf5SvcAddDLCI | 1.3.6.1.4.1.321.100.1.25.6.1.1.12 | INTEGER | read-write | Identifies a DLCI number to be added. |
| INT ipadAtmFrf5SvcDeleteDLCI | 1.3.6.1.4.1.321.100.1.25.6.1.1.13 | INTEGER | read-write | Identifies a DLCI number to be deleted. |
| ipadAtmFrf5DlciTable | 1.3.6.1.4.1.321.100.1.25.6.2 | not-accessible | Table of Mapped DLCIs for VCCs. This table is used for FRF5 to map one or more DLCIs to a VCC. When only one DLCI is mapped, a one-to-one relationship exists between the DLCI and the VCC. When more than one DLCI is mapped, a many-to-one DLCI/VCC relationship exists. | |
| ipadAtmFrf5DlciTableEntry | 1.3.6.1.4.1.321.100.1.25.6.2.1 | not-accessible | An entry in the ipad ATM Vcc parameter table. | |
| INT ipadAtmFrf5DlciIfIndex | 1.3.6.1.4.1.321.100.1.25.6.2.1.1 | INTEGER | read-only | The index into the ATM FRF5 DLCI table, corresponding to ifIndex. |
| INT ipadAtmFrf5DlciVpiIndex | 1.3.6.1.4.1.321.100.1.25.6.2.1.2 | INTEGER | read-only | The VPI index into the ATM FRF5 DLCI table. |
| INT ipadAtmFrf5DlciVciIndex | 1.3.6.1.4.1.321.100.1.25.6.2.1.3 | INTEGER | read-only | The VCI index into the ATM FRF5 DLCI table. |
| INT ipadAtmFrf5DlciIndex | 1.3.6.1.4.1.321.100.1.25.6.2.1.4 | INTEGER | read-only | The DLCI index into the ATM FRF5 DLCI table. |
| STR ipadAtmFrf5DlciEndpointName | 1.3.6.1.4.1.321.100.1.25.6.2.1.5 | DisplayString | read-write | Identifies the attached endpoint for this FRF5 DLCI. |
| INT ipadAtmFrf5DlciStatus | 1.3.6.1.4.1.321.100.1.25.6.2.1.6 | INTEGER | read-only | The current status of this mapped entry. |
| INT ipadAtmFrf5DlciCongestion | 1.3.6.1.4.1.321.100.1.25.6.2.1.7 | INTEGER | read-only | Specifies if the dlci is receiving frames with FECN or BECN bit set. |
| ipadAtmFrf8SvcTable | 1.3.6.1.4.1.321.100.1.25.6.3 | not-accessible | Table of ATM FRF8 profile parameters. | |
| ipadAtmFrf8SvcTableEntry | 1.3.6.1.4.1.321.100.1.25.6.3.1 | not-accessible | An entry in the ipad ATM FRF8 service table. | |
| INT ipadAtmFrf8SvcIfIndex | 1.3.6.1.4.1.321.100.1.25.6.3.1.1 | INTEGER | read-only | The index representing the ATM interface. |
| INT ipadAtmFrf8SvcVpiIndex | 1.3.6.1.4.1.321.100.1.25.6.3.1.2 | INTEGER | read-only | The index representing the VPI of the VCC. |
| INT ipadAtmFrf8SvcVciIndex | 1.3.6.1.4.1.321.100.1.25.6.3.1.3 | INTEGER | read-only | The index representing the VCI of the VCC. |
| INT ipadAtmFrf8SvcDeToClpMappingMode | 1.3.6.1.4.1.321.100.1.25.6.3.1.4 | INTEGER | read-write | This object describes which mode of translation is in use for loss priority mapping in the frame relay to ATM direction. mode1(1) = the DE field in the Q.922 core frame shall be mapped to the ATM CLP field of every cell generated by the segmentation process of the AAL5 PDU containing the information of that frame. mode2Contst0(2) = the ATM CLP field of every cell generated by the segmentation process of the AAL5 PDU containing the information of that frame shall be set to constant 0. mode2Contst1(3) = the ATM CLP field of every cell generated by the segmentation process of the AAL5 PDU containing the information of that frame shall be set to constant 1. |
| INT ipadAtmFrf8SvcClpToDeMappingMode | 1.3.6.1.4.1.321.100.1.25.6.3.1.5 | INTEGER | read-write | This object describes which mode of translation is in use for loss priority mapping in the ATM to frame relay direction. mode1(1) = if one or more cells in a frame has its CLP field set, the DE field of the Q.922 core frame should be set. mode2Const0(2) = the DE field of the Q.922 core frame should be set to the constant 0. mode2Const1(3) = the DE field of the Q.922 core frame should be set to the constant 1. |
| INT ipadAtmFrf8SvcCongestionMappingMode | 1.3.6.1.4.1.321.100.1.25.6.3.1.6 | INTEGER | read-write | This object describes which mode of translation is in use for forward congestion indication mapping in the frame relay to ATM direction. mode1(1) = The FECN field in the Q.922 core frame shall be mapped to the ATM EFCI field of every cell generated by the segmentation process of the AAL5 PDU containing the information of that frame. mode2(2) = The FECN field in the Q.922 core frame shall not be mapped to the ATM EFCI field of cells generated by the segmentation process of the AAL5 PDU containing the information of that frame. The EFCI field is always set to 'congestion not experienced'. In both of the modes above, if there is congestion in the forward direction in the ATM layer within the IWF, then the IWF can set the EFCI field to 'congestion experienced'. |
| INT ipadAtmFrf8SvcEncapsulationMappingMode | 1.3.6.1.4.1.321.100.1.25.6.3.1.7 | INTEGER | read-write | This object indicates whether the mapping of upper layer protocol encapsulation is enabled on this interworking connection. transparentMode(1) = Forward the encapsulations unaltered. translationMode(2) = Perform mapping between the two encapsulations due to the incompatibilities of the two methods. |
| STR ipadAtmFrf8SvcEndpointName | 1.3.6.1.4.1.321.100.1.25.6.3.1.8 | DisplayString | read-write | Identifies the Frame Relay endpoint for this FRF8 Service. |
RFC description
IPAD ATM (Asynchronous Transfer Mode) interface parameters, statistics, and virtual circuit management for Verilink IPAD devices.
Start monitoring Verilink IPAD ATM access multiplexer with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.