All MIBs › NNCEXTPVC-MIB
Organization: Alcatel Networks Corporation
Last Updated: 2001-01-26
Category: ATM
Description: Manages Alcatel/Newbridge Networks permanent virtual circuit configuration and status on ATM interfaces.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is NNCEXTPVC-MIB?
NNCEXTPVC-MIB is Alcatel/Newbridge Networks' proprietary MIB for managing Permanent Virtual Connections (PVCs) on Cell Relay (ATM) interfaces, covering both point-to-point and point-to-multipoint connections. It belongs to the ATM WAN switching technology area. It exposes configuration and status data for Permanent Virtual Path Connections (PVPCs, via nncCrPvpcTable) and Permanent Virtual Channel Connections (PVCCs, via nncCrPvccTable), supporting creation, modification, query, and deletion of these circuits, including cross-connections between Cell Relay and Frame Relay endpoints. Its role in monitoring is centered on configuration/status visibility, verifying that provisioned PVCs/PVPCs remain correctly configured and operationally up rather than exposing hardware environmental sensors. It is a proprietary extension layered on top of standard ATM PVC concepts rather than a direct dependency on a specific IETF MIB. It is typically deployed on Newbridge/Alcatel ATM switches in carrier networks provisioning permanent virtual circuits between customer sites. Engineers can download the NNCEXTPVC-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in NNCEXTPVC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Alcatel/Newbridge Networks ATM switch
Monitoring Examples
An operator would query nncCrPvpcTable and nncCrPvccTable to confirm the row status and endpoint configuration of a provisioned PVPC or PVCC, checking that a circuit connecting a Cell Relay endpoint to a Frame Relay endpoint remains active. If a PVC's row status shows other than active, or endpoint parameters mismatch, this indicates a misconfigured or torn-down permanent circuit needing correction. The MIB's row-based create/modify/delete model means monitoring here largely means polling connection status rather than performance counters.
What Can Be Monitored
- PVPC connection status
- PVCC connection status
- PVC endpoint configuration
- PVC row/administrative status
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex |
From NNCGNI0001-SMI
| nncExtensions | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| INT nncCrPvccBwdAbrDynTrfcIcr | 1.3.6.1.4.1.123.3.79.1.2.1.13 | INTEGER | read-create | ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s |
| INT nncCrPvccBwdAbrDynTrfcRdf | 1.3.6.1.4.1.123.3.79.1.2.1.15 | INTEGER | read-create | ABR traffic Rate Decrease Factor descriptor for the destination endpoint. Value is expressed as the -power of 2 Range: 0 - 9 |
| INT nncCrPvccBwdAbrDynTrfcRif | 1.3.6.1.4.1.123.3.79.1.2.1.14 | INTEGER | read-create | ABR traffic Rate Increase Factor for the destination endpoint. Value is expressed as the -power of 2. Range: 0 - 9 |
| INT nncCrPvccBwdServiceCategory | 1.3.6.1.4.1.123.3.79.1.2.1.9 | INTEGER | read-create | This object is used to set the traffic service category from destination end point to source endpoint. This object is dependent on the value specified in nncCrPvccBwdTmTrafficDescripton object |
| INT nncCrPvccBwdTmBucketOneCdvt | 1.3.6.1.4.1.123.3.79.1.2.1.30 | INTEGER | read-create | This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds |
| INT nncCrPvccBwdTmBucketOneRate | 1.3.6.1.4.1.123.3.79.1.2.1.29 | INTEGER | read-create | This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s |
| INT nncCrPvccBwdTmBucketTwoMbs | 1.3.6.1.4.1.123.3.79.1.2.1.32 | INTEGER | read-create | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells |
| INT nncCrPvccBwdTmBucketTwoRate | 1.3.6.1.4.1.123.3.79.1.2.1.31 | INTEGER | read-create | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s |
| INT nncCrPvccBwdTmCdv | 1.3.6.1.4.1.123.3.79.1.2.1.33 | INTEGER | read-create | This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds |
| INT nncCrPvccBwdTmClr | 1.3.6.1.4.1.123.3.79.1.2.1.34 | INTEGER | read-create | The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# Range: 0 - 7 |
| INT nncCrPvccBwdTmFrameDiscard | 1.3.6.1.4.1.123.3.79.1.2.1.35 | INTEGER | read-create | The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of the ATM cell header. |
| INT nncCrPvccBwdTmPolicingOption | 1.3.6.1.4.1.123.3.79.1.2.1.28 | INTEGER | read-create | Policing Option for an PVCC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor |
| INT nncCrPvccBwdTmTrafficDescriptor | 1.3.6.1.4.1.123.3.79.1.2.1.27 | INTEGER | read-create | This object contains the traffic descriptor for the SPVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only) |
| INT nncCrPvccCastType | 1.3.6.1.4.1.123.3.79.1.2.1.7 | INTEGER | read-create | This object is used to indicate whether the PVCC is point-to-point or point-to-multipoint |
| INT nncCrPvccCreator | 1.3.6.1.4.1.123.3.79.1.2.1.38 | INTEGER | read-only | The object retrieves the creator of a PVC connection. |
| INT nncCrPvccDstAlsConfig | 1.3.6.1.4.1.123.3.79.1.2.1.37 | INTEGER | read-create | This object is used to set OAM Alarm Surveillance configuration for the destination endpoint. |
| INT nncCrPvccDstBillingFlag | 1.3.6.1.4.1.123.3.79.1.2.1.17 | INTEGER | read-create | Billing Configuration for the destination endpoint. |
| NUM nncCrPvccDstIfIndex | 1.3.6.1.4.1.123.3.79.1.2.1.4 | InterfaceIndex | not-accessible | This object contains the ifIndex value for the destination endpoint. |
| INT nncCrPvccDstVci | 1.3.6.1.4.1.123.3.79.1.2.1.6 | INTEGER | not-accessible | This object contains the VCI value for the destination endpoint. |
| INT nncCrPvccDstVpi | 1.3.6.1.4.1.123.3.79.1.2.1.5 | INTEGER | not-accessible | This object contains the VPI value for the destination endpoint. |
| INT nncCrPvccFwdAbrDynTrfcIcr | 1.3.6.1.4.1.123.3.79.1.2.1.10 | INTEGER | read-create | ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s |
| INT nncCrPvccFwdAbrDynTrfcRdf | 1.3.6.1.4.1.123.3.79.1.2.1.12 | INTEGER | read-create | ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
| INT nncCrPvccFwdAbrDynTrfcRif | 1.3.6.1.4.1.123.3.79.1.2.1.11 | INTEGER | read-create | ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
| INT nncCrPvccFwdServiceCategory | 1.3.6.1.4.1.123.3.79.1.2.1.8 | INTEGER | read-create | This object is used to set the traffic service category from source endpoint to destination endpoint. This object is dependent on the value specified in nncCrPvccFwdTmTrafficDescripton object |
| INT nncCrPvccFwdTmBucketOneCdvt | 1.3.6.1.4.1.123.3.79.1.2.1.21 | INTEGER | read-create | This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds |
| INT nncCrPvccFwdTmBucketOneRate | 1.3.6.1.4.1.123.3.79.1.2.1.20 | INTEGER | read-create | This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s |
| INT nncCrPvccFwdTmBucketTwoMbs | 1.3.6.1.4.1.123.3.79.1.2.1.23 | INTEGER | read-create | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells |
| INT nncCrPvccFwdTmBucketTwoRate | 1.3.6.1.4.1.123.3.79.1.2.1.22 | INTEGER | read-create | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s |
| INT nncCrPvccFwdTmCdv | 1.3.6.1.4.1.123.3.79.1.2.1.24 | INTEGER | read-create | This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds |
| INT nncCrPvccFwdTmClr | 1.3.6.1.4.1.123.3.79.1.2.1.25 | INTEGER | read-create | The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# |
| INT nncCrPvccFwdTmFrameDiscard | 1.3.6.1.4.1.123.3.79.1.2.1.26 | INTEGER | read-create | The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of the ATM cell header. |
| INT nncCrPvccFwdTmPolicingOption | 1.3.6.1.4.1.123.3.79.1.2.1.19 | INTEGER | read-create | Policing Option for a PVcC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor |
| INT nncCrPvccFwdTmTrafficDescriptor | 1.3.6.1.4.1.123.3.79.1.2.1.18 | INTEGER | read-create | This object contains the traffic descriptor for the PVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only) |
| nncCrPvccGroup | 1.3.6.1.4.1.123.3.79.3.2 | Common MIB objects for configuring a CR PVCC on Alcatel CID equipment | ||
| ROW nncCrPvccRowStatus | 1.3.6.1.4.1.123.3.79.1.2.1.39 | RowStatus | read-create | This object is to control a row creation of a CR PVCC. When RowStatus is createAndWait, information for a row is cached in memory; when RowStatus is set to createAndGo or active, it indicates that all information is to be written to permanent storage, and the PVCC to be enabled. When querying the object, 'active' indicates the PVCC is physically connected and data traffic can flow. The Rowstatus of 'notInService' indicates the PVCC is physically connected but data cannot flow. If the RowStatus value of 'notReady' is returned, it indicates either the PVCC is not physically connected (ie. configured only) or the SNMP agent is awaiting further information before setting up the connection. When deleting a connection, use this object with the value 'destroy' |
| INT nncCrPvccSrcAlsConfig | 1.3.6.1.4.1.123.3.79.1.2.1.36 | INTEGER | read-create | This object is used to set OAM Alarm Surveillance configuration for the source endpoint. |
| INT nncCrPvccSrcBillingFlag | 1.3.6.1.4.1.123.3.79.1.2.1.16 | INTEGER | read-create | Billing Configuration for the source endpoint. |
| NUM nncCrPvccSrcIfIndex | 1.3.6.1.4.1.123.3.79.1.2.1.1 | InterfaceIndex | not-accessible | This object contains the ifIndex value for the source endpoint. |
| INT nncCrPvccSrcVci | 1.3.6.1.4.1.123.3.79.1.2.1.3 | INTEGER | not-accessible | This object contains the VCI value for the source endpoint. |
| INT nncCrPvccSrcVpi | 1.3.6.1.4.1.123.3.79.1.2.1.2 | INTEGER | not-accessible | This object contains the VPI value for the source endpoint. |
| nncCrPvccTable | 1.3.6.1.4.1.123.3.79.1.2 | not-accessible | nncCrPvccTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query Cell Relay PVC connections. | |
| nncCrPvccTableEntry | 1.3.6.1.4.1.123.3.79.1.2.1 | not-accessible | An entry of nncCrPvccTable. It contains the objects required to manage CR PVCs. | |
| INT nncCrPvpcBwdAbrDynTrfcIcr | 1.3.6.1.4.1.123.3.79.1.1.1.11 | INTEGER | read-create | ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s |
| INT nncCrPvpcBwdAbrDynTrfcRdf | 1.3.6.1.4.1.123.3.79.1.1.1.13 | INTEGER | read-create | ABR traffic Rate Decrease Factor descriptor for the destination endpoint. Value is expressed as the -power of 2 Range: 0 - 9 |
| INT nncCrPvpcBwdAbrDynTrfcRif | 1.3.6.1.4.1.123.3.79.1.1.1.12 | INTEGER | read-create | ABR traffic Rate Increase Factor for the destination endpoint. Value is expressed as the -power of 2. Range: 0 - 9 |
| INT nncCrPvpcBwdServiceCategory | 1.3.6.1.4.1.123.3.79.1.1.1.7 | INTEGER | read-create | This object is used to set the traffic service category from destination endpoint to source endpoint. This object is dependent on the value specified in nncCrPvpcBwdTmTrafficDescripton object |
| INT nncCrPvpcBwdTmBucketOneCdvt | 1.3.6.1.4.1.123.3.79.1.1.1.27 | INTEGER | read-create | This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds |
| INT nncCrPvpcBwdTmBucketOneRate | 1.3.6.1.4.1.123.3.79.1.1.1.26 | INTEGER | read-create | This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s |
| INT nncCrPvpcBwdTmBucketTwoMbs | 1.3.6.1.4.1.123.3.79.1.1.1.29 | INTEGER | read-create | This object is to set the maximum burst size, in cells, for SIR_0p or SIR_0+1p. Used for burst traffic. Range: 1 - 10000 cells |
| INT nncCrPvpcBwdTmBucketTwoRate | 1.3.6.1.4.1.123.3.79.1.1.1.28 | INTEGER | read-create | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s |
| INT nncCrPvpcBwdTmCdv | 1.3.6.1.4.1.123.3.79.1.1.1.30 | INTEGER | read-create | This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds |
| INT nncCrPvpcBwdTmClr | 1.3.6.1.4.1.123.3.79.1.1.1.31 | INTEGER | read-create | The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# Range: 1 - 7 |
| INT nncCrPvpcBwdTmPolicingOption | 1.3.6.1.4.1.123.3.79.1.1.1.25 | INTEGER | read-create | Policing Option for a PVPC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor |
| INT nncCrPvpcBwdTmTrafficDescriptor | 1.3.6.1.4.1.123.3.79.1.1.1.24 | INTEGER | read-create | This object contains the traffic descriptor for the PVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only) |
| INT nncCrPvpcCastType | 1.3.6.1.4.1.123.3.79.1.1.1.5 | INTEGER | read-create | This object is used to indicate whether the PVPC is point-to-point or point-to-multipoint |
| INT nncCrPvpcCreator | 1.3.6.1.4.1.123.3.79.1.1.1.34 | INTEGER | read-only | The object retrieves the creator of a PVC connection. |
| INT nncCrPvpcDstAlsConfig | 1.3.6.1.4.1.123.3.79.1.1.1.33 | INTEGER | read-create | This object is used to set OAM Alarm Surveillance configuration for the destination endpoint. |
| INT nncCrPvpcDstBillingFlag | 1.3.6.1.4.1.123.3.79.1.1.1.15 | INTEGER | read-create | Billing Configuration for the destination endpoint. |
| NUM nncCrPvpcDstIfIndex | 1.3.6.1.4.1.123.3.79.1.1.1.3 | InterfaceIndex | not-accessible | This object contains the ifIndex value for the destination endpoint |
| INT nncCrPvpcDstVpi | 1.3.6.1.4.1.123.3.79.1.1.1.4 | INTEGER | not-accessible | This object contains the VPI value for the destination endpoint. |
| INT nncCrPvpcFwdAbrDynTrfcIcr | 1.3.6.1.4.1.123.3.79.1.1.1.8 | INTEGER | read-create | ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s |
| INT nncCrPvpcFwdAbrDynTrfcRdf | 1.3.6.1.4.1.123.3.79.1.1.1.10 | INTEGER | read-create | ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
| INT nncCrPvpcFwdAbrDynTrfcRif | 1.3.6.1.4.1.123.3.79.1.1.1.9 | INTEGER | read-create | ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
| INT nncCrPvpcFwdServiceCategory | 1.3.6.1.4.1.123.3.79.1.1.1.6 | INTEGER | read-create | This object is used to set the traffic service category from source endpoint to destination endpoint. This object is dependent on the value specified in nncCrPvpcFwdTmTrafficDescripton object |
| INT nncCrPvpcFwdTmBucketOneCdvt | 1.3.6.1.4.1.123.3.79.1.1.1.19 | INTEGER | read-create | This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds |
| INT nncCrPvpcFwdTmBucketOneRate | 1.3.6.1.4.1.123.3.79.1.1.1.18 | INTEGER | read-create | This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s |
| INT nncCrPvpcFwdTmBucketTwoMbs | 1.3.6.1.4.1.123.3.79.1.1.1.21 | INTEGER | read-create | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells |
| INT nncCrPvpcFwdTmBucketTwoRate | 1.3.6.1.4.1.123.3.79.1.1.1.20 | INTEGER | read-create | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s |
| INT nncCrPvpcFwdTmCdv | 1.3.6.1.4.1.123.3.79.1.1.1.22 | INTEGER | read-create | This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category.. Range: 250-10000 microseconds |
| INT nncCrPvpcFwdTmClr | 1.3.6.1.4.1.123.3.79.1.1.1.23 | INTEGER | read-create | The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# |
| INT nncCrPvpcFwdTmPolicingOption | 1.3.6.1.4.1.123.3.79.1.1.1.17 | INTEGER | read-create | Policing Option for a PVPC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor |
| INT nncCrPvpcFwdTmTrafficDescriptor | 1.3.6.1.4.1.123.3.79.1.1.1.16 | INTEGER | read-create | This object contains the traffic descriptor for the SPVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only) |
| nncCrPvpcGroup | 1.3.6.1.4.1.123.3.79.3.1 | Common MIB objects for configuring a CR PVPC on Alcatel CID equipment | ||
| ROW nncCrPvpcRowStatus | 1.3.6.1.4.1.123.3.79.1.1.1.35 | RowStatus | read-create | This object is to control a row creation of a CR PVPC. When RowStatus is createAndWait, information for a row is cached in memory; when RowStatus is set to createAndGo or active, it indicates that all information is to be written to permanent storage, and the PVPC to be enabled. When querying the object, 'active' indicates the PVPC is physically connected and data traffic can flow. The Rowstatus of 'notInService' indicates the PVPC is physically connected but data cannot flow. If the RowStatus value of 'notReady' is returned, it indicates either the PVPC is not physically connected (ie. configured only) or the SNMP agent is awaiting further information before setting up the connection. When deleting a connection, use this object with the value 'destroy' |
| INT nncCrPvpcSrcAlsConfig | 1.3.6.1.4.1.123.3.79.1.1.1.32 | INTEGER | read-create | This object is used to set OAM Alarm Surveillance configuration for the source endpoint. |
| INT nncCrPvpcSrcBillingFlag | 1.3.6.1.4.1.123.3.79.1.1.1.14 | INTEGER | read-create | Billing Configuration for the source endpoint. |
| NUM nncCrPvpcSrcIfIndex | 1.3.6.1.4.1.123.3.79.1.1.1.1 | InterfaceIndex | not-accessible | This object contains the ifIndex value for the source endpoint |
| INT nncCrPvpcSrcVpi | 1.3.6.1.4.1.123.3.79.1.1.1.2 | INTEGER | not-accessible | This object contains the VPI value for the source endpoint. |
| nncCrPvpcTable | 1.3.6.1.4.1.123.3.79.1.1 | not-accessible | nncCrPvpcTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query PVC connections. | |
| nncCrPvpcTableEntry | 1.3.6.1.4.1.123.3.79.1.1.1 | not-accessible | An entry of nncCrPvpcTable | |
| nncExtPvc | 1.3.6.1.4.1.123.3.79 | This module contains Alcatel's proprietary MIB definition for managing point-to-point and point-to-multipoint Permanent Virtual Connections (PVCs). The MIB supports the creation, modification, query and deletion of PVCs (Permanent Virtual Connections) on Cell Relay endpoints, both Permanent Virtual Path Connection (PVPC) and Permanent Virtual Channel Connection (PVCC) are supported. PVPCs are defined by nncCrPvpcTable and PVCCs are defined by nncCrPvccTable. PVPCs or PVCC's connecting different endpoint types, CR to FR, FR to CR, CR to CE, CE to CR, CE to FR or FR to CE are not suppported at this point. Resource connections such as Signalling, PNNI, ILMI and CPSS are also not supported. PVCs can be created by one of two ways: using rowStats as 'createAndGo' or using rowStatus as 'createAndWait'+'active'. In some cases, to create a PVC via this table requires two SET-REQs, because one SET-REQ PDU cannot fit all required objects. In these cases, the rowStatus is set to createAndWait(5) for the first 1 SET-REQ and set to active(1) for the last SET-REQ. In some cases, all required MIB objects can fit in one SET-REQ PDU. In these cases the rowStatus should be set to createAndGo(4) To delete a PVC, the SNMP manager should set rowStatus of the PVC instance to 'destroy'. Each PVC is modeled as set of entries in the PVC table. A point- to-point PVC is modeled as one entry; a point-to-multipoint (N leafs) is modeled as N entries in this table. The N entries of a point-to- multipoint PVC shares the same source end point. Some abreviations: abr/ABR/Abr: Available Bit Rate Bwd: Backward. For traffice descriptors from destination end point to source end point cbr/CBR/Cbr: Constant Bit Rate Dst: Dstination end point Fwd: Forward. For traffic descriptors from source end point to destination end point nt-vbr/ntvbr/NT-VBR: Non-Real-Time Variable Bit Rate p2p: Point-to-Point p2mp: Point-to-Multipoint Src: Source end point Targ: Target. For the destination end point info in source end point table ubr/UBR/Ubr: Unspecified Bit Rate VCI/Vci/vci: Virtual channel identifier VCL/Vcl/vcl: Virtual channel link VPI/Vpi/vpi: Virtual path identifier VPL/Vpl/Vpl: Virtual path link | ||
| nncExtPvcCompliances | 1.3.6.1.4.1.123.3.79.4 | |||
| nncExtPvcGroups | 1.3.6.1.4.1.123.3.79.3 | |||
| nncExtPvcObjects | 1.3.6.1.4.1.123.3.79.1 | |||
| nncPvcCompliance | 1.3.6.1.4.1.123.3.79.4.1 | The compliance statement for Alcatel CID PVC MIB implementation. |
RFC description
Alcatel management of Permanent Virtual Connections (PVCs) on cell relay and ATM endpoints.
Start monitoring Alcatel/Newbridge Networks ATM switch (Permanent Virtual Connections) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.