ACMIB (page 2 of 2) - SNMP MIB Browser

OID symbolic	OID numeric	Type	Access	Description
INT tasTrapTstId	1.3.6.1.4.1.1751.2.18.15.51	INTEGER	read-only	Announcement ID for trap.
INT tasTrapAnnceId	1.3.6.1.4.1.1751.2.18.15.52	INTEGER	read-only	test id for trap.
INT atmVpi	1.3.6.1.4.1.1751.2.18.15.53	INTEGER	read-only	Vpi is used in identification of Traps
INT atmVci	1.3.6.1.4.1.1751.2.18.15.54	INTEGER	read-only	Vci is used in identification of Traps
INT iptResultCode	1.3.6.1.4.1.1751.2.18.15.55	INTEGER	read-only	Various result codes for the operator's command forsetting/deleting interface protection group. interfaceProtectioniptAlreadyExistInterface: Expect another interface to be protected. interfaceProtectioniptInvalidInterface:interface invalid interfaceProtectioniptInvalidParams: invalid Parameters interfaceProtectioniptTryToDeleteEmptyTable:Table is already empty,can not be deleted . interfaceProtectioniptInvalidConfiguation: interfaceProtectioniptSuccessfulSwichOver: interface is switched over to the secondry interface. interfaceProtectioniptSuccessfulSwichBack: interface is switched back from secondry interface. interfaceProtectioniptFailedSwichOver: interface is failed switched over to the secondry interface. interfaceProtectioniptFailedSwichBack: interface is failed switched back from secondry interface.
INT pgtResultCode	1.3.6.1.4.1.1751.2.18.15.56	INTEGER	read-only	Various result codes for the operator's command for interface protection .
INT tasmControlBlockAllocFailReasonCode	1.3.6.1.4.1.1751.2.18.15.57	INTEGER	read-only	The result of a tasm control block memory allocation request.
INT tasmCacheMemAllocFailReasonCode	1.3.6.1.4.1.1751.2.18.15.58	INTEGER	read-only	The result of a tasm control block memory allocation request.
INT atmTrunkingConfigFailureCode	1.3.6.1.4.1.1751.2.18.15.59	INTEGER	read-only	An identified reason for failure while configuring/modifying ATM Trunking parameters: localIWFAlreadyConfigured(1) : Local IWF has already been configured, the parameters can not be changed or apply again. localIWFAtmAddressError(2): the ATM Address for Local IWF is not valid or this address has been used by someone else. localIWFIdOutOfRange(3): the Identification of Local IWF is out of range. maxNumberRmtIWFOutOfRange(4): the maximum number of Remote IWF is out of range. rmtIWFAlreadyConfigured(5): this remote IWF has already been configured( with index atmTrunkingRmtIWFIdentifier). rmtIWFIdOutOfRange: the identifier for the remote IWF is out of range. rmtIWFAtmAddressError: the ATM Address for remote IWF is not valid or this address has been used by someone else. vccIdError: the VCC ID for the SigVcc or BrVcc is 0, or this VCC ID is out of range or it has been used by someone else. vccPvcParameterNotAcceptable: the parameters of PVC side, including slot, port, channel, vpi, vci, are not acceptable. vccTrafficParameterNotValid: the VCC traffic parameters are not acceptable, including FwPcr01, BwPcr01, FwScr01, BwScr01, FWMbs01, BwMbs01, BrVccServiceType, BrVccSarType. vccViVuniNotValid: the configuration of Egress Vi/VUNI is not acceptable. vccTrunkParameterNotValid: the parameters for the Trunk is not supported, including BrVccMaxAal2ChanId, BrVccCircuitModeDataSupp, BrVccFrameModeSupp, BrVccFaxModeSupp, CASPktXportSupp, BrVccDTMFPktXportSupp, BrVccMFR1PktXportSupp, BrVccMFR2PktXportSupp, BrVccPCMEncoding, BrVccMaxFrameLength, BrVccIdleChannSuprSupp, BrVccSilenceDetSupp, BrVccCompressionSpec,AudioProfileId, SigVccSignaling. vccTrunkFeatureParameterNotValid: PSAX proprietary feature parameters not supported including SigVccInactiveTimer, SigVccRetryTimer, SigVccRetryLimit, BrVccInactiveTimer, BrVccRetryTimer, BrVccRetryLimit, BrVccGr303Supp, BrVccOamStatus. localIwfNotConfigured(14) : Local IWF not Configured localIwfIdNotMatch(15): specified Local IWF not match localIwfStatus(16): this operation is not supported because of the status of Local IWF rmtIwfNotConfigured(17): Remote IWF Not Configured rmtIwfModeNotCompatible(18): the Mode of Remote IWF is not compatiable rmtIwfStatus(19): this operation is not support because of the Status of Remote IWF vccAlreadyConfigured(20): This VCC has been configured vccPvcCacReject(21): PVC Configuration rejected by Cac Reservation Function requiredFieldMissing(22): mandatory fields missing outOfResource(23): Atm Trunking Task or System out of resource for this configuration rowStatusError(24):Row Status Error with the SNMP command generalErrorUnspecified(25): all other unspecified failure cause.
INT sapphireIntfAddressFailReasonCode	1.3.6.1.4.1.1751.2.18.15.60	INTEGER	read-only	The result of assigning the Sapphire Interface address when PSAX is Sapphire client. address-ok(1), Address assignment succeeded fail-Ilegal-IP-address(2), Illegal IP address assigned address not matching fail-not-match-InBandManagement-Switch-CPU-IP-Address(3) In-Band Management IP or Switch IP or CPU IP address fail-Switch-or-CPU-IP-Address-unconfigured(4) Switch IP or CPU IP address unconfigured fail-InBandManagement-IP-Address-unconfigured(5) InBandManagement IP address unconfigured.
INT chassisOverTempAlarmReasonCode	1.3.6.1.4.1.1751.2.18.15.61	INTEGER	read-only	Indicator of presence of chassis over temperature alarm.
sysControl	1.3.6.1.4.1.1751.2.18.16
INT saveConfiguration	1.3.6.1.4.1.1751.2.18.16.1	INTEGER	read-write	save configuration
INT upgradeSoftware	1.3.6.1.4.1.1751.2.18.16.2	INTEGER	read-write	software load management
NUM purgePvcConnections	1.3.6.1.4.1.1751.2.18.16.3	IntfIndex	read-write	purge PVC connections on indicated interface
INT purgeRoutingTable	1.3.6.1.4.1.1751.2.18.16.4	INTEGER	read-write	purge indicated routing table
I32 resetPortStatistics	1.3.6.1.4.1.1751.2.18.16.5	Integer32	read-write	Reset the statistics counters for the given port Id (SSPP)
NUM resetInterfaceStatistics	1.3.6.1.4.1.1751.2.18.16.6	IntfIndex	read-write	Reset the interface counters for the given port Id (SSPPCCC)
I32 resetAllStatistics	1.3.6.1.4.1.1751.2.18.16.7	Integer32	read-write	Reset all port and interface statistics counters, accpets any integer value
IP upgradeIpAddress	1.3.6.1.4.1.1751.2.18.16.8	IpAddress	read-write	IP Address for upgrade ftp server.
STR upgradeAccountName	1.3.6.1.4.1.1751.2.18.16.9	DisplayString	read-write	ftp account name for access to upgrade ftp server.
STR upgradeAccountPassword	1.3.6.1.4.1.1751.2.18.16.10	DisplayString	read-write	ftp account password for access to upgrade ftp server.
STR upgradeCdromFile	1.3.6.1.4.1.1751.2.18.16.11	DisplayString	read-write	cdrom file path on upgrade ftp server to upgrade image library.
STR upgradeLicenseKey	1.3.6.1.4.1.1751.2.18.16.12	DisplayString	read-write	software license key.
INT upgradeSwCopyStatus	1.3.6.1.4.1.1751.2.18.16.13	INTEGER	read-only	Current status of the ftp software upgrade download. Status of the software upgrade. noActivity is the initial start state from boot-up. working is set while ftp'ing the upgrade. The final state is one of doneSuccessfully, doneWithError, or aborted, all self-explanatory. It will stay in this state until re-boot or starting an upgrade. If the state is doneWithError then upgradeSwErrorStatus will be set to reflect the type of error.
INT upgradeSwErrorStatus	1.3.6.1.4.1.1751.2.18.16.14	INTEGER	read-only	The result of the finish of the ftp software upgrade download. Set to a value 3-22 if upgradeSwCopyStatus is doneWithError. Set to none if upgradeSwCopyStatus is doneSuccessfully. Set to userAbort if upgradeSwCopyStatus is aborted.
INT systemSwCopy	1.3.6.1.4.1.1751.2.18.16.15	INTEGER	read-write	start copy system files according to the profile. When upgradeSwCopyStatus is working, the start request will be ignored. Abort will have effect only when upgradeSwCopystatus is working.
fwReleaseTable	1.3.6.1.4.1.1751.2.18.16.16		not-accessible	Table of firmware inventory data
fwReleaseEntry	1.3.6.1.4.1.1751.2.18.16.16.1		not-accessible	Row definition for firmware inventory
INT fwReleaseSlot	1.3.6.1.4.1.1751.2.18.16.16.1.1	INTEGER	not-accessible	Physical slot location. Valid range is a number between 1 and 16.
OCT fwReleaseRunning	1.3.6.1.4.1.1751.2.18.16.16.1.2	OCTET STRING	read-only	the firmware release currently running in a physical slot (e.g., 01.03.C01).
OCT fwReleaseEpromVersion	1.3.6.1.4.1.1751.2.18.16.16.1.3	OCTET STRING	read-only	the version of the firmware located on the I/O card (e.g., 01.03.C01).
OCT fwReleaseCurrentVersion	1.3.6.1.4.1.1751.2.18.16.16.1.4	OCTET STRING	read-only	the version of the firmware located in /scsi/current/io on the CPU disk drive (e.g., 01.03.C01).
OCT fwReleaseNextVersion	1.3.6.1.4.1.1751.2.18.16.16.1.5	OCTET STRING	read-only	the version of the firmware located in /scsi/next/io on the CPU disk drive (e.g., 01.03.C01).
INT fwReleaseUpdate	1.3.6.1.4.1.1751.2.18.16.16.1.6	INTEGER	read-write	Update the fwReleaseCurrentVersion and the fwReleaseNextVersion variables by remapping the firmware files from the CPU disk drive.
INT fwReleaseUpgrade	1.3.6.1.4.1.1751.2.18.16.16.1.7	INTEGER	read-write	Update the fwReleaseCurrentVersion and the fwReleaseNextVersion variables by remapping the firmware files from the CPU disk drive.
I32 resetBridgeDomainStatistics	1.3.6.1.4.1.1751.2.18.16.17	Integer32	read-write	Resets bridge domain statistics.
INT remoteRebootCommand	1.3.6.1.4.1.1751.2.18.16.18	INTEGER	read-write	type of reboot.
I32 resetFrLmiStatistics	1.3.6.1.4.1.1751.2.18.16.19	Integer32	read-write	Reset the frame relay LMI statistics counters for the given port Id (SSPPCCC)
INT removeConfigurationFiles	1.3.6.1.4.1.1751.2.18.16.20	INTEGER	read-write	Removes the user configuration/connection files from the hard disk on the cpu.
INT systemFilesDirtyBitStatus	1.3.6.1.4.1.1751.2.18.16.21	INTEGER	read-only	Bit mask for system files: 0: all are clean 1: console.def 2: ecd.def 4: ssid.def 8: cnctn.db 16: iisp.cbr 32: iisp.vbr 64: spvc.db 128: vipr.cfg 256: fwc.def 512: vi.db 1024: iproute.db 2048: atmvuni.db
I32 resetAtmIlmiStatistics	1.3.6.1.4.1.1751.2.18.16.22	Integer32	read-write	Reset the ATM ILMI statistics counters for the given channel Id (SSPPCCC)
NUM resetImaGrpChannelStatistics	1.3.6.1.4.1.1751.2.18.16.23	IntfIndex	read-write	Reset the IMA Group Statistics counters for the given port Id (SSPPCCC)
I32 oc3APSResetStats	1.3.6.1.4.1.1751.2.18.16.24	Integer32	read-write	Reset the oc3aps Group Statistics counters for the given port Id (SSPP)
I32 resetsonetSectionStatistics	1.3.6.1.4.1.1751.2.18.16.25	Integer32	read-write	Reset the sonetSectionCurrent Statistics counters for the given port Id (SSPP)
I32 resetsonetLineStatistics	1.3.6.1.4.1.1751.2.18.16.26	Integer32	read-write	Reset the sonetLineCurrent Statistics counters for the given port Id (SSPP)
I32 resetsonetVTPathStatistics	1.3.6.1.4.1.1751.2.18.16.27	Integer32	read-write	Reset the sonetVTPathCurrent Statistics counters for the given port Id (SSPP)
I32 viprVpnReset	1.3.6.1.4.1.1751.2.18.16.28	Integer32	read-write	Reset the VPN statistics for VPN specified by (SSVV)
INT svcRetBackupStatus	1.3.6.1.4.1.1751.2.18.16.29	INTEGER	read-only	Indicates backup status wrt SVC retention
I32 resetsonetPathStatistics	1.3.6.1.4.1.1751.2.18.16.30	Integer32	read-write	Reset the sonetPathCurrent Statistics counters for the given port Id (SSPP)
I32 ambientTemperature	1.3.6.1.4.1.1751.2.18.16.31	Integer32	read-only	Ambient temperature in degree Celcius where the system is kept
remoteDbServerGroup	1.3.6.1.4.1.1751.2.18.16.32
IP remoteDbServerIpAddress	1.3.6.1.4.1.1751.2.18.16.32.1	IpAddress	read-write	IP Address for remote database server.
STR remoteDbServerLogin	1.3.6.1.4.1.1751.2.18.16.32.2	DisplayString	read-write	ftp account name for remote database server.
STR remoteDbServerPassword	1.3.6.1.4.1.1751.2.18.16.32.3	DisplayString	read-write	ftp account password for remote database server.
STR remoteDbServerDirectory	1.3.6.1.4.1.1751.2.18.16.32.4	DisplayString	read-write	directory on remote database server where to save/restore database files from.
INT remoteDbCommand	1.3.6.1.4.1.1751.2.18.16.32.5	INTEGER	read-write	remote database operation.
INT remoteDbOperationStatus	1.3.6.1.4.1.1751.2.18.16.32.6	INTEGER	read-only	Current status of remote database command.
INT remoteDbOperationErrorStatus	1.3.6.1.4.1.1751.2.18.16.32.7	INTEGER	read-only	The result at the finish of remote database operation.
stratumConfig	1.3.6.1.4.1.1751.2.18.17
INT stratumSyncSource	1.3.6.1.4.1.1751.2.18.17.1	INTEGER	read-write	Clock source for the stratum card - lineTiming: must have slot and port specified in stratumPrimaryLineId. compositeClock: local clock must be available.
I32 stratumPrimaryLineId	1.3.6.1.4.1.1751.2.18.17.2	Integer32	read-write	Format SSPP (slot and port #'s) to be used when lineTiming is specified in stratumSyncSource.
I32 stratumSecondaryLineId	1.3.6.1.4.1.1751.2.18.17.3	Integer32	read-write	Format SSPP (slot and port #'s) to be used if the primary line has failed. Zeros imply that the stratum should switch to holdover mode instead.
INT stratumLevel	1.3.6.1.4.1.1751.2.18.17.4	INTEGER	read-write	Enable or disable the switching over to stratum 4 when stratum 3 is not possible.
INT stratumLineCommand	1.3.6.1.4.1.1751.2.18.17.5	INTEGER	read-write	Forces the stratum card to use one of the two specified lines as its clock source when the stratumSyncSource is lineTiming.
INT stratumLineTimingStatus	1.3.6.1.4.1.1751.2.18.17.6	INTEGER	read-only	Represents the source of the current clock.
INT stratumMode	1.3.6.1.4.1.1751.2.18.17.7	INTEGER	read-only	Current status of the primary stratum card. synchronized3(1) stratum is synchronized with accuracy 4.6 x 10e-6 synchronized4(2) stratum is synchronized with accuracy 3.2 x 10e-5 holdover(3) an operating condition of a clock that has lost its controlling input and is using stored data acquired while in normal operation, to control its output freerun(4) an operating condition of the clock whose output signals are internally controlled cardRemoved(5) stratum removed
INT stratumBackupMode	1.3.6.1.4.1.1751.2.18.17.8	INTEGER	read-only	Current status of the backup stratum card.
INT stratumRefFailAction	1.3.6.1.4.1.1751.2.18.17.9	INTEGER	read-write	Defines whether the stratum should switch to freerun or holdover on reference clock failure.
INT stratumPortStatus	1.3.6.1.4.1.1751.2.18.17.10	INTEGER	read-only	Current status of the primary stratum card. portFOS indicates port frequency offset.
INT stratumBkupPortStatus	1.3.6.1.4.1.1751.2.18.17.11	INTEGER	read-only	Current status of the backup stratum card. portFOS indicates port frequency offset.
INT activeStratum	1.3.6.1.4.1.1751.2.18.17.12	INTEGER	read-only	Current status of the backup stratum card.
cellTest	1.3.6.1.4.1.1751.2.18.18
NUM cellTestIfB	1.3.6.1.4.1.1751.2.18.18.1	IntfIndex	read-write	Interface index used for testing cell transfer. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
INT cellTestVpiB	1.3.6.1.4.1.1751.2.18.18.2	INTEGER	read-write	VPI value for testing cell transfer to an I/O card. Valid range is a number between 0 and 4095. If the I/O card interface is not ATM, then this will always be zero.
INT cellTestVcidB	1.3.6.1.4.1.1751.2.18.18.3	INTEGER	read-write	Virtual Check Id for testing cell transfer to an I/O card. Valid range is a number between 0 and 65535. If the I/O card interface is frame relay, this field acts as DLCI and the valid range is a number between 0 and 1023. If the I/O card interface is circuit emulation, then this will always be 0.
INT cellTestServiceType	1.3.6.1.4.1.1751.2.18.18.4	INTEGER	read-write	Service types for testing cell transfer
INT cellTestConnType	1.3.6.1.4.1.1751.2.18.18.5	INTEGER	read-write	Connection types for testing cell transfer
INT cellTestProtocol	1.3.6.1.4.1.1751.2.18.18.6	INTEGER	read-only	Protocol (interface type) on the I/O
OCT cellTestPayLoadTx	1.3.6.1.4.1.1751.2.18.18.7	OCTET STRING	read-write	PayLoad to be transmitted on I/O interface
OCT cellTestPayLoadRx	1.3.6.1.4.1.1751.2.18.18.8	OCTET STRING	read-only	Last PayLoad received on I/O interface
INT cellTestAction	1.3.6.1.4.1.1751.2.18.18.9	INTEGER	read-write	PayLoad received on I/O interface
I32 cellTestRxPduCount	1.3.6.1.4.1.1751.2.18.18.10	Integer32	read-only	Valid cells received (Input Billing Count)
I32 cellTestTxPduCount	1.3.6.1.4.1.1751.2.18.18.11	Integer32	read-only	Valid cells transmitted (Output Billing Count)
I32 cellTestMismatchPduCount	1.3.6.1.4.1.1751.2.18.18.12	Integer32	read-only	Number of times Rx payload mismatched with Tx payload.
INT cellTestStatus	1.3.6.1.4.1.1751.2.18.18.13	INTEGER	read-only	Indicates whether a cellTest test is in progress or not.
INT cellTestVUNIB	1.3.6.1.4.1.1751.2.18.18.14	INTEGER	read-write	VUNI id for testing cell transfer to an I/O card. This field is valid only for ATM interface.
sysInfo	1.3.6.1.4.1.1751.2.18.19
I32 sysInfoTxOneCellTotal	1.3.6.1.4.1.1751.2.18.19.1	Integer32	read-only	Total amount of cells within the transmit one cell pool.
I32 sysInfoTxOneCellUsed	1.3.6.1.4.1.1751.2.18.19.2	Integer32	read-only	Amount of cells currently being used within the transmit one cell pool.
I32 sysInfoTxOneCellHigh	1.3.6.1.4.1.1751.2.18.19.3	Integer32	read-only	High-water mark of cells used within the transmit one cell pool.
I32 sysInfoRxOneCellTotal	1.3.6.1.4.1.1751.2.18.19.4	Integer32	read-only	Total amount of cells within the receive one cell pool.
I32 sysInfoRxOneCellUsed	1.3.6.1.4.1.1751.2.18.19.5	Integer32	read-only	Amount of cells currently being used within the receive one cell pool.
I32 sysInfoRxOneCellHigh	1.3.6.1.4.1.1751.2.18.19.6	Integer32	read-only	High-water mark of cells used within the receive one cell pool.
I32 sysInfoRxMultiCellTotal	1.3.6.1.4.1.1751.2.18.19.7	Integer32	read-only	Total amount of multi-cells within the receive multi-cell pool.
I32 sysInfoRxMultiCellUsed	1.3.6.1.4.1.1751.2.18.19.8	Integer32	read-only	Amount of multi-cells currently being used within the receive multi-cell pool.
I32 sysInfoRxMultiCellHigh	1.3.6.1.4.1.1751.2.18.19.9	Integer32	read-only	High-water mark of multi-cells used within the receive multi-cell pool.
I32 sysInfoMsgPoolTotal	1.3.6.1.4.1.1751.2.18.19.10	Integer32	read-only	Total amount of messages within the message pool.
I32 sysInfoMsgPoolUsed	1.3.6.1.4.1.1751.2.18.19.11	Integer32	read-only	Amount of messages currently being used within the message pool.
I32 sysInfoMsgPoolHigh	1.3.6.1.4.1.1751.2.18.19.12	Integer32	read-only	High-water mark of messages used within the message pool.
I32 sysInfoDiscFreeKBytes	1.3.6.1.4.1.1751.2.18.19.13	Integer32	read-only	Amount of disc free space available in KB's.
INT sysInfoCpuUtilization1	1.3.6.1.4.1.1751.2.18.19.14	INTEGER	read-only	xx.yy% - cpuUtilization1 is the xx part of it.
INT sysInfoCpuUtilization2	1.3.6.1.4.1.1751.2.18.19.15	INTEGER	read-only	xx.yy% - cpuUtilization2 is the yy part of it.
I32 sysInfoSysUptime	1.3.6.1.4.1.1751.2.18.19.16	Integer32	read-only	Amount of time cpu has been up in seconds.
I32 sysInfoBadCellRx	1.3.6.1.4.1.1751.2.18.19.17	Integer32	read-only	The number of bad cells (BIP16) received so far.
I32 sysInfoMisaligned	1.3.6.1.4.1.1751.2.18.19.18	Integer32	read-only	The number of misaligned cells received so far.
INT sysInfoClockAErr	1.3.6.1.4.1.1751.2.18.19.19	INTEGER	read-only	Value is 1, TRUE, if the clock on backplane A is errored, otherwise, the value is 0, FALSE.
INT sysInfoClockBErr	1.3.6.1.4.1.1751.2.18.19.20	INTEGER	read-only	Value is 1, TRUE, if the clock on backplane B is errored, otherwise, the value is 0, FALSE.
INT sysInfoBIPAErr	1.3.6.1.4.1.1751.2.18.19.21	INTEGER	read-only	Value is 1, TRUE, if the cell circuit on backplane A is errored, otherwise, the value is 0, FALSE.
INT sysInfoBIPBErr	1.3.6.1.4.1.1751.2.18.19.22	INTEGER	read-only	Value is 1, TRUE, if the cell circuit on backplane B is errored, otherwise, the value is 0, FALSE.
I32 sysInfoDiscTotalKBytes	1.3.6.1.4.1.1751.2.18.19.23	Integer32	read-only	Amount of disc space available in KB's.
I32 sysInfoRAMFreeKBytes	1.3.6.1.4.1.1751.2.18.19.24	Integer32	read-only	Amount of RAM memory available for use in KB's.
I32 sysInfoRAMTotalKBytes	1.3.6.1.4.1.1751.2.18.19.25	Integer32	read-only	Amount of RAM memory available on cpu card in KB's.
msgPoolViewTable	1.3.6.1.4.1.1751.2.18.19.26		not-accessible	Table of Msg Pools In the System, Used only for diagnostic purposes
msgPoolViewEntry	1.3.6.1.4.1.1751.2.18.19.26.1		not-accessible	Row definition of Msg Pool Table
I32 msgPoolViewIndex	1.3.6.1.4.1.1751.2.18.19.26.1.1	Integer32	not-accessible	It is the index of the MsgPool array for which the information is requested. Information about Msgs Which are not there in the free pool is returned.A msg is said to be out of the free pool by comparing the signature. The limit being the max number of msgs allowed on the system
I32 msgPoolViewTskId	1.3.6.1.4.1.1751.2.18.19.26.1.2	Integer32	read-only	Task Id of the Sender of the Particular Msg, This will give the integer value, has to be converted to hex for comparison
STR msgPoolViewTskName	1.3.6.1.4.1.1751.2.18.19.26.1.3	DisplayString	read-only	Task Name of the Sender of the Particular Msg
I32 msgPoolViewMsgCmd	1.3.6.1.4.1.1751.2.18.19.26.1.4	Integer32	read-only	msgCmd being sent by the sending Task
INT primaryCpuHwType	1.3.6.1.4.1.1751.2.18.19.27	INTEGER	read-only	Indicates the hardware version type of the primary CPU. version1: 150MHz Saturn13 board supporting 8MB-64MB Memory. version2: 200MHz Saturn15 board supporting 64MB-256MB Memory.
INT secondaryCpuHwType	1.3.6.1.4.1.1751.2.18.19.28	INTEGER	read-only	Indicates the hardware version type of the secondary CPU. version1: 150MHz Saturn13 board supporting 8MB-64MB Memory. version2: 200MHz Saturn15 board supporting 64MB-256MB Memory.
INT sysInfoDiskCheck	1.3.6.1.4.1.1751.2.18.19.29	INTEGER	read-only	Indicates the checking status of the disk in CPU card.
INT switchAlarmStatus	1.3.6.1.4.1.1751.2.18.19.30	INTEGER	read-only	Current status of the alarm on the switch. notAvailable - The alarm status could not be retreived. none - No alarm is present. minor, major, critical - An alarm of the enumerated type is present
ethernetConfig	1.3.6.1.4.1.1751.2.18.20
arp1Table	1.3.6.1.4.1.1751.2.18.20.1		not-accessible	Table of ARP cache data.
arp1Entry	1.3.6.1.4.1.1751.2.18.20.1.1		not-accessible	Row definition for ARP cache.
INT arp1CardSlot	1.3.6.1.4.1.1751.2.18.20.1.1.1	INTEGER	not-accessible	Slot ethernet card is in.
INT arp1BridgeGroupNum	1.3.6.1.4.1.1751.2.18.20.1.1.2	INTEGER	not-accessible	Bridge Group the entry belongs to.
IP arp1IpAddress	1.3.6.1.4.1.1751.2.18.20.1.1.3	IpAddress	not-accessible	Entry IP address.
OCT arp1PhysicalAddr	1.3.6.1.4.1.1751.2.18.20.1.1.4	OCTET STRING	read-only	Entry physical address.
I32 arp1EntryAge	1.3.6.1.4.1.1751.2.18.20.1.1.5	Integer32	read-only	Age of cache entry.
arp2Table	1.3.6.1.4.1.1751.2.18.20.2		not-accessible	Table of ARP cache data.
arp2Entry	1.3.6.1.4.1.1751.2.18.20.2.1		not-accessible	Row definition for ARP cache.
INT arp2CardSlot	1.3.6.1.4.1.1751.2.18.20.2.1.1	INTEGER	not-accessible	Slot ethernet card is in.
INT arp2BridgeGroupNum	1.3.6.1.4.1.1751.2.18.20.2.1.2	INTEGER	not-accessible	Bridge Group the entry belongs to.
OCT arp2PhysicalAddr	1.3.6.1.4.1.1751.2.18.20.2.1.3	OCTET STRING	not-accessible	Entry physical address.
IP arp2IpAddress	1.3.6.1.4.1.1751.2.18.20.2.1.4	IpAddress	read-only	Entry IP address.
I32 arp2EntryAge	1.3.6.1.4.1.1751.2.18.20.2.1.5	Integer32	read-only	Age of cache entry.
bridgeCacheTable	1.3.6.1.4.1.1751.2.18.20.3		not-accessible	Table of bridge cache data.
bridgeCacheEntry	1.3.6.1.4.1.1751.2.18.20.3.1		not-accessible	Row definition for bridge cache.
INT bridgeCacheCardSlot	1.3.6.1.4.1.1751.2.18.20.3.1.1	INTEGER	not-accessible	Slot ethernet card is in.
INT bridgeCacheBridgeGroupNum	1.3.6.1.4.1.1751.2.18.20.3.1.2	INTEGER	not-accessible	Bridge Group the entry belongs to.
OCT bridgeCachePhysicalAddr	1.3.6.1.4.1.1751.2.18.20.3.1.3	OCTET STRING	not-accessible	Entry physical address.
INT bridgeCacheType	1.3.6.1.4.1.1751.2.18.20.3.1.4	INTEGER	read-only	Type of Entry.
INT bridgeCacheSourcePort	1.3.6.1.4.1.1751.2.18.20.3.1.5	INTEGER	read-only	Port entry was obtained from.
I32 bridgeCacheEntryAge	1.3.6.1.4.1.1751.2.18.20.3.1.6	Integer32	read-only	Age of cache entry.
alarmConfig	1.3.6.1.4.1.1751.2.18.21
OCT alarmStatusInputBitmap	1.3.6.1.4.1.1751.2.18.21.1	OCTET STRING	read-only	Remote status from external device. bit = 0 closed, bit = 1 open, LSB 15 bits represent 15 external inputs. MSB bit 15 is always 0.
OCT alarmStatusOutputBitmap	1.3.6.1.4.1.1751.2.18.21.2	OCTET STRING	read-write	Control output for alarm card. bit = 0 deactivated, bit = 1 activated, LSB 4 bits represent 4 external outputs. Bit 0 through bit 3 is output 1 through 4 Control output 4 will be activated upon power failure.
OCT alarmSeverityLevelBitmap	1.3.6.1.4.1.1751.2.18.21.3	OCTET STRING	read-write	Alarm severity level. bit = 0 noAlarm, bit = 1 Alarm present, LSB 3 bits represent severity levels. bit 0 = Minor Alarm, bit 1 = Major Alarm, bit 2 = Critical Alarm.
OCT alarmAcoStatusBitmap	1.3.6.1.4.1.1751.2.18.21.4	OCTET STRING	read-only	Audio alarm status. bit = 0 No alarm cutoff, bit = 1 Alarm cutoff, LSB 3 bits represent audio alarms. bit 0 = Local alarm cutoff, bit 1 = remote alarm cutoff, bit 2 = composite alarm cutoff status.
sysTest	1.3.6.1.4.1.1751.2.18.22
oamTest	1.3.6.1.4.1.1751.2.18.22.1
NUM oamTestIfB	1.3.6.1.4.1.1751.2.18.22.1.1	IntfIndex	read-write	Interface index used for starting loopback test. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
INT oamTestVpiB	1.3.6.1.4.1.1751.2.18.22.1.2	INTEGER	read-write	VPI value under testing for oam loopback test. Valid range is a number between 0 and 4095.
INT oamTestVciB	1.3.6.1.4.1.1751.2.18.22.1.3	INTEGER	read-write	VCI value under testing for oam loopback test. Valid range is a number between 0 and 65535.
INT oamTestStatus	1.3.6.1.4.1.1751.2.18.22.1.4	INTEGER	read-only	Inidcates the current status of oam test.
INT oamTestAction	1.3.6.1.4.1.1751.2.18.22.1.5	INTEGER	read-write	Test action to be performed.
I32 oamTestTxCount	1.3.6.1.4.1.1751.2.18.22.1.6	Integer32	read-only	Valid cells transmitted.
I32 oamTestRxCount	1.3.6.1.4.1.1751.2.18.22.1.7	Integer32	read-only	Valid cells received.
I32 oamTestMismatchCount	1.3.6.1.4.1.1751.2.18.22.1.8	Integer32	read-only	Number of times Rx correlation tag is mismatched with the Tx correlation tag.
OCT oamTestLocationID	1.3.6.1.4.1.1751.2.18.22.1.9	OCTET STRING	read-write	Location ID of the ATM Node where the loopback is to occur.
INT oamTestLoopbackType	1.3.6.1.4.1.1751.2.18.22.1.10	INTEGER	read-write	OAM Loopback type. Determines whether to send ete or segment loopback cell, and the value of location Id field in the cell. Only for specific-location value, user specified locationId field value taken into account.
oamActDeactTable	1.3.6.1.4.1.1751.2.18.22.2		not-accessible	Table of oam activate and deactivate functions
oamActDeactEntry	1.3.6.1.4.1.1751.2.18.22.2.1		not-accessible	Row definition of oam activate and deactivate
NUM oamActDeactIfB	1.3.6.1.4.1.1751.2.18.22.2.1.1	IntfIndex	not-accessible	Interface index for an OAM CC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
INT oamActDeactVpiB	1.3.6.1.4.1.1751.2.18.22.2.1.2	INTEGER	not-accessible	VPI value for an oam CC connection. Valid range is a number between 0 and 4095.
INT oamActDeactVciB	1.3.6.1.4.1.1751.2.18.22.2.1.3	INTEGER	not-accessible	VCI value for oam CC connection. Valid range is a number between 0 and 65535.
INT oamActDeactFuncType	1.3.6.1.4.1.1751.2.18.22.2.1.4	INTEGER	read-write	OAM Function type represents the OAM flow for activation or deactivattion for this connection. the possible function types activated in one connection are : fpm-and-br : forward performance monitoring/backward reporting fpm-only : forward performance monitoring continuity-check : continuity check pmbr-and-cc : forward performance monitoring/backward reporting and continuity check pm-and-cc : forward performance monitoring and continuity check
INT oamActDeactDirFlow	1.3.6.1.4.1.1751.2.18.22.2.1.5	INTEGER	read-write	The direction in which cells will be transmitted.
INT oamActDeactFlowType	1.3.6.1.4.1.1751.2.18.22.2.1.6	INTEGER	read-write	Flow Type.
INT oamActDeactBlkSizeAB	1.3.6.1.4.1.1751.2.18.22.2.1.7	INTEGER	read-write	Block Size A-B represents the size of the block of user cells taken into consideration for performance monitoring in A-B direction.
INT oamActDeactBlkSizeBA	1.3.6.1.4.1.1751.2.18.22.2.1.8	INTEGER	read-write	Block Size A-B is the size of the block of user cells taken into consideration for performance monitoring in B-A direction.
INT oamActDeactStsSrcPointEteCC	1.3.6.1.4.1.1751.2.18.22.2.1.9	INTEGER	read-only	Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
INT oamActDeactStsSnkPointEteCC	1.3.6.1.4.1.1751.2.18.22.2.1.10	INTEGER	read-only	Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
INT oamActDeactRsltPrevReq	1.3.6.1.4.1.1751.2.18.22.2.1.11	INTEGER	read-only	Cause of Failure shows the reasons of failure of the last activation request on this connection form the local user.
ROW oamActDeactRowStatus	1.3.6.1.4.1.1751.2.18.22.2.1.12	RowStatus	read-write	row status
INT oamActDeactStsSrcPointEtePM	1.3.6.1.4.1.1751.2.18.22.2.1.13	INTEGER	read-only	Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
INT oamActDeactStsSnkPointEtePM	1.3.6.1.4.1.1751.2.18.22.2.1.14	INTEGER	read-only	Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
INT oamActDeactStsSrcPointEtePMBR	1.3.6.1.4.1.1751.2.18.22.2.1.15	INTEGER	read-only	Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
INT oamActDeactStsSnkPointEtePMBR	1.3.6.1.4.1.1751.2.18.22.2.1.16	INTEGER	read-only	Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
INT oamActDeactBRBlockError	1.3.6.1.4.1.1751.2.18.22.2.1.17	INTEGER	read-only	Backware reporting Block error for PM connection. Valid range is a number between 0 and 32768.
INT oamActDeactBRLostInsertedCell	1.3.6.1.4.1.1751.2.18.22.2.1.18	INTEGER	read-only	Backware reporting lost inserted cell for PM connection. Valid range is a number between 0 and 32768.
INT oamActDeactBRMisInsertedCell	1.3.6.1.4.1.1751.2.18.22.2.1.19	INTEGER	read-only	Backware reporting misinserted cell for PM connection. Valid range is a number between 0 and 32768.
INT oamActDeactStsSrcPointSegPM	1.3.6.1.4.1.1751.2.18.22.2.1.20	INTEGER	read-only	Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
INT oamActDeactStsSnkPointSegPM	1.3.6.1.4.1.1751.2.18.22.2.1.21	INTEGER	read-only	Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
INT oamActDeactStsSrcPointSegPMBR	1.3.6.1.4.1.1751.2.18.22.2.1.22	INTEGER	read-only	Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
INT oamActDeactStsSnkPointSegPMBR	1.3.6.1.4.1.1751.2.18.22.2.1.23	INTEGER	read-only	Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
INT oamActDeactStsSrcPointSegCC	1.3.6.1.4.1.1751.2.18.22.2.1.24	INTEGER	read-only	Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
INT oamActDeactStsSnkPointSegCC	1.3.6.1.4.1.1751.2.18.22.2.1.25	INTEGER	read-only	Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
oamLoopbackTable	1.3.6.1.4.1.1751.2.18.22.3		not-accessible	Table of oam loopback functions
oamLoopbackEntry	1.3.6.1.4.1.1751.2.18.22.3.1		not-accessible	Row definition of oam loop back
NUM oamLpbkIfB	1.3.6.1.4.1.1751.2.18.22.3.1.1	IntfIndex	not-accessible	Interface index used for starting loopback test. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
INT oamLpbkVpiB	1.3.6.1.4.1.1751.2.18.22.3.1.2	INTEGER	not-accessible	VPI value under testing for oam loopback test. Valid range is a number between 0 and 4095.
INT oamLpbkVciB	1.3.6.1.4.1.1751.2.18.22.3.1.3	INTEGER	not-accessible	VCI value under testing for oam loopback test. Valid range is a number between 0 and 65535.
INT oamLoopbackType	1.3.6.1.4.1.1751.2.18.22.3.1.4	INTEGER	read-write	OAM Loopback type. Determines whether to send ete or segment loopback cell, and the value of location Id field in the cell. Only for specific-location value, user specified locationId field value taken into account.
OCT oamLpbkLocationID	1.3.6.1.4.1.1751.2.18.22.3.1.5	OCTET STRING	read-write	Location ID of the ATM Node where the loopback is to occur.
INT oamLpbkAction	1.3.6.1.4.1.1751.2.18.22.3.1.6	INTEGER	read-write	Test action to be performed. endLoopbackContinuously is not used.
INT oamLpbkStatus	1.3.6.1.4.1.1751.2.18.22.3.1.7	INTEGER	read-only	Inidcates the current status of oam test.
I32 oamLpbkTxCount	1.3.6.1.4.1.1751.2.18.22.3.1.8	Integer32	read-only	Valid cells transmitted.
I32 oamLpbkRxCount	1.3.6.1.4.1.1751.2.18.22.3.1.9	Integer32	read-only	Valid cells received.
I32 oamLpbkMismatchCount	1.3.6.1.4.1.1751.2.18.22.3.1.10	Integer32	read-only	Number of times Rx correlation tag is mismatched with the Tx correlation tag.
I32 oamLpbkTimeout	1.3.6.1.4.1.1751.2.18.22.3.1.11	Integer32	read-only	number of time out
fwDriverSup	1.3.6.1.4.1.1751.2.18.23
cardFwVerTable	1.3.6.1.4.1.1751.2.18.23.1		not-accessible	Table of card firware version status
cardFwVerEntry	1.3.6.1.4.1.1751.2.18.23.1.1		not-accessible	Row definition for card firmware version status
INT cardFwVerSlot	1.3.6.1.4.1.1751.2.18.23.1.1.1	INTEGER	not-accessible	card slot number
I32 cardFwVerType	1.3.6.1.4.1.1751.2.18.23.1.1.2	Integer32	read-write	Card type
OCT cardFwVerCurrent	1.3.6.1.4.1.1751.2.18.23.1.1.3	OCTET STRING	read-only	Card firmware version currently loaded on firmware
I32 cardFwVerCurrentIsDefault	1.3.6.1.4.1.1751.2.18.23.1.1.4	Integer32	read-only	curent driver is default
OCT cardFwVerNext	1.3.6.1.4.1.1751.2.18.23.1.1.5	OCTET STRING	read-write	Card firmware version that user wants to upgrade to. The values are limited those supported by the release.
INT cardFwVerNextIsDefault	1.3.6.1.4.1.1751.2.18.23.1.1.6	INTEGER	read-write	next driver is default
INT cardFwDnldStatus	1.3.6.1.4.1.1751.2.18.23.1.1.7	INTEGER	read-only	firmware download procedure status
I32 cardFwRetries	1.3.6.1.4.1.1751.2.18.23.1.1.8	Integer32	read-only	Number of times firmware download procedure failed consequently.
fwDriverTable	1.3.6.1.4.1.1751.2.18.23.2		not-accessible	Table of available firmware drivers
fwDriverEntry	1.3.6.1.4.1.1751.2.18.23.2.1		not-accessible	Row definition for available firmware drivers
I32 fwSlotId	1.3.6.1.4.1.1751.2.18.23.2.1.1	Integer32	not-accessible	driver slot id
I32 fwDriverType	1.3.6.1.4.1.1751.2.18.23.2.1.2	Integer32	not-accessible	firmware driver type - definition consistent with cardType.
I32 fwIsDefault	1.3.6.1.4.1.1751.2.18.23.2.1.3	Integer32	not-accessible	firmware driver wether default or not
OCT fwDriverName	1.3.6.1.4.1.1751.2.18.23.2.1.4	OCTET STRING	not-accessible	firmware driver file name
I32 fwDriverFrn	1.3.6.1.4.1.1751.2.18.23.2.1.5	Integer32	read-only	Firmware Release Number of firmware driver
I32 fwDriverSize	1.3.6.1.4.1.1751.2.18.23.2.1.6	Integer32	read-only	file size of firmware driver
I32 fwDriverChecksum	1.3.6.1.4.1.1751.2.18.23.2.1.7	Integer32	read-only	checksum of firmware driver file
viprConfig	1.3.6.1.4.1.1751.2.18.24
viprRouterConfigTable	1.3.6.1.4.1.1751.2.18.24.1		not-accessible	Table of Vipr Router Instance Information
viprRouterConfigEntry	1.3.6.1.4.1.1751.2.18.24.1.1		not-accessible	definition for VIPR Route instance attributes
I32 viprSlot	1.3.6.1.4.1.1751.2.18.24.1.1.1	Integer32	not-accessible	The slot number of the Virtual Router card (SS)
INT viprRouterId	1.3.6.1.4.1.1751.2.18.24.1.1.2	INTEGER	not-accessible	A unique Id for the Router Instance in a router card
STR viprRouterName	1.3.6.1.4.1.1751.2.18.24.1.1.3	DisplayString	read-write	The ASCII name of the Router Instance
INT viprRouterNoOfInterfaces	1.3.6.1.4.1.1751.2.18.24.1.1.4	INTEGER	read-only	This variable describes the no of interfaces defined in the Router Instance
INT viprRouterNoOfRoutes	1.3.6.1.4.1.1751.2.18.24.1.1.5	INTEGER	read-only	This variable describes the no of static routes defined in the Router Instance
INT viprRouterAdminStatus	1.3.6.1.4.1.1751.2.18.24.1.1.6	INTEGER	read-write	This variable represents the various X.731 states the Router state machine can take Administartively
INT viprRouterOperStatus	1.3.6.1.4.1.1751.2.18.24.1.1.7	INTEGER	read-only	This variable represents the various X.731 states the Router state machine can take operationally
I32 viprRouterInitTmr	1.3.6.1.4.1.1751.2.18.24.1.1.8	Integer32	read-write	This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.
I32 viprRouterDisabWarnTmr	1.3.6.1.4.1.1751.2.18.24.1.1.9	Integer32	read-write	This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.
I32 viprRouterShutDwnWarnTmr	1.3.6.1.4.1.1751.2.18.24.1.1.10	Integer32	read-write	This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.
INT viprRouterDisableWarning	1.3.6.1.4.1.1751.2.18.24.1.1.11	INTEGER	read-write	This variable when disabled will mask all the warning messages.
INT viprRouterDisableReason	1.3.6.1.4.1.1751.2.18.24.1.1.12	INTEGER	read-only	This variable describes the reason why the Router in the unlocked-Disabled state.
ROW viprRouterRowStatus	1.3.6.1.4.1.1751.2.18.24.1.1.13	RowStatus	read-write	row status
viprIntfConfigTable	1.3.6.1.4.1.1751.2.18.24.2		not-accessible	Table of Vipr Interface Config Information
viprIntfConfigEntry	1.3.6.1.4.1.1751.2.18.24.2.1		not-accessible	definition for VIPR interface attributes
I32 viprIntfId	1.3.6.1.4.1.1751.2.18.24.2.1.1	Integer32	not-accessible	A unique Id for the Interface in a router instance
IP viprIntfIPAddress	1.3.6.1.4.1.1751.2.18.24.2.1.2	IpAddress	read-write	The IP address of the entrprise network to which the interface is attached to
IP viprIntfIPNetMask	1.3.6.1.4.1.1751.2.18.24.2.1.3	IpAddress	read-write	The IP Subnet Mask of the entrprise network to which the interface is attached to
INT viprIntfAdminStatus	1.3.6.1.4.1.1751.2.18.24.2.1.4	INTEGER	read-write	This variable represents the various X.731 states the Interfce statemachine can take Administratively
INT viprIntfOperStatus	1.3.6.1.4.1.1751.2.18.24.2.1.5	INTEGER	read-only	This variable represents the various X.731 states the Interfce statemachine can take operationally
I32 viprIntfInitTmr	1.3.6.1.4.1.1751.2.18.24.2.1.6	Integer32	read-write	This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.
I32 viprIntfDisabWarnTmr	1.3.6.1.4.1.1751.2.18.24.2.1.7	Integer32	read-write	This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.
I32 viprIntfShutDwnWarnTmr	1.3.6.1.4.1.1751.2.18.24.2.1.8	Integer32	read-write	This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.
INT viprIntfDisableWarning	1.3.6.1.4.1.1751.2.18.24.2.1.9	INTEGER	read-write	This variable when disabled will mask all the Disable warning messages.
INT viprIntfDisableReason	1.3.6.1.4.1.1751.2.18.24.2.1.10	INTEGER	read-only	This variable describes the reason why the Interface in the unlocked-Disabled state.
INT viprIntfRipVersion	1.3.6.1.4.1.1751.2.18.24.2.1.11	INTEGER	read-write	This specifies the version of RIP that interface supports.
INT viprIntfRipMode	1.3.6.1.4.1.1751.2.18.24.2.1.12	INTEGER	read-write	This specifies the mode in which RIP protocol runs.
ROW viprIntfRowStatus	1.3.6.1.4.1.1751.2.18.24.2.1.13	RowStatus	read-write	row status
INT viprIntfRipLineType	1.3.6.1.4.1.1751.2.18.24.2.1.14	INTEGER	read-write	This specifies the line type when the RIP version is 2. When the RIP version is 1, the RIP line type will be set to broadcast(1).
STR viprIntfAuthPasswd	1.3.6.1.4.1.1751.2.18.24.2.1.15	DisplayString	read-write	The authentication password for RIP version 2
viprSubChnlConfigTable	1.3.6.1.4.1.1751.2.18.24.3		not-accessible	Table of Vipr Sub Channel Config Information
viprSubChnlConfigEntry	1.3.6.1.4.1.1751.2.18.24.3.1		not-accessible	definition for VIPR sub channel attributes
I32 viprSubChnlId	1.3.6.1.4.1.1751.2.18.24.3.1.1	Integer32	not-accessible	A unique Id for the sub channel in the interface
NUM viprSubChnlIntfIndex	1.3.6.1.4.1.1751.2.18.24.3.1.2	IntfIndex	read-write	The Slot Port Channel to which the IP Packet to be forwarded when the TOS specified in the incoming IP packet is matched to the TosValue, TosMask pair
INT viprSubChnlTrafficType	1.3.6.1.4.1.1751.2.18.24.3.1.3	INTEGER	read-write	The type of interface configured on the SSPPCCC, viprSubChnlIntfIndex
INT viprSubChnlLlcEncapType	1.3.6.1.4.1.1751.2.18.24.3.1.4	INTEGER	read-write	The encapsulation technique used in making IP packet to ATM cell
INT viprSubChnlMacEncapType	1.3.6.1.4.1.1751.2.18.24.3.1.5	INTEGER	read-write	The encapsulation technique used in making IP packet to ATM cell
INT viprSubChnlTosFeature	1.3.6.1.4.1.1751.2.18.24.3.1.6	INTEGER	read-only	Allow the user to set the TOS values or not
INT viprSubChnlTosValue	1.3.6.1.4.1.1751.2.18.24.3.1.7	INTEGER	read-only	The type of service specified in IP packet masked with viprSubChnlTosMask has to be equal to this value in order to have the IP packets getting forwarded in this sub channel
INT viprSubChnlTosMask	1.3.6.1.4.1.1751.2.18.24.3.1.8	INTEGER	read-only	The Type of Service mask
INT viprSubChnlVpiDlci	1.3.6.1.4.1.1751.2.18.24.3.1.9	INTEGER	read-write	The VPI/DLCI value of the connection
INT viprSubChnlVci	1.3.6.1.4.1.1751.2.18.24.3.1.10	INTEGER	read-write	The VCI value of the connection
INT viprSubChnlSarType	1.3.6.1.4.1.1751.2.18.24.3.1.11	INTEGER	read-only	The SAR Type supported for the connection
INT viprSubChnlServiceType	1.3.6.1.4.1.1751.2.18.24.3.1.12	INTEGER	read-write	The Service types that are supported
INT viprSubChnlFwdErrCorrection	1.3.6.1.4.1.1751.2.18.24.3.1.13	INTEGER	read-write	The Forward error correction to be used
INT viprSubChnlInterworkingType	1.3.6.1.4.1.1751.2.18.24.3.1.14	INTEGER	read-write	The Encapsulation type used for Frame relay subchannels
I32 viprSubChnlFrameSize	1.3.6.1.4.1.1751.2.18.24.3.1.15	Integer32	read-write	The value of this object is the size in octets of the largest frame relay information field for this PVC in the ingress direction (out of the frame relay UNI).
I32 viprSubChnlComBurstSize	1.3.6.1.4.1.1751.2.18.24.3.1.16	Integer32	read-write	The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this PVC in the ingress direction (into the frame relay UNI).
I32 viprSubChnlExcessBurstSize	1.3.6.1.4.1.1751.2.18.24.3.1.17	Integer32	read-write	The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this PVC in the ingress direction (into the frame relay UNI).
I32 viprSubChnlCommitedInfoRate	1.3.6.1.4.1.1751.2.18.24.3.1.18	Integer32	read-write	The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this PVC in the ingress direction (into the frame relay UNI).
INT viprSubChnlTimeInterval	1.3.6.1.4.1.1751.2.18.24.3.1.19	INTEGER	read-only	The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.
I32 viprSubChnlAtmPeakCellRate	1.3.6.1.4.1.1751.2.18.24.3.1.20	Integer32	read-write	Peak cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.
I32 viprSubChnlAtmSustainedCellRate	1.3.6.1.4.1.1751.2.18.24.3.1.21	Integer32	read-write	Sustained cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.
I32 viprSubChnlAtmMaxBurstSize	1.3.6.1.4.1.1751.2.18.24.3.1.22	Integer32	read-write	Maximum burst size, in cells, this will reflect the frame relay parameters in atm terms.
I32 viprSubChnlFrPeakCellRate	1.3.6.1.4.1.1751.2.18.24.3.1.23	Integer32	read-only	Peak cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.
I32 viprSubChnlFrSustainedCellRate	1.3.6.1.4.1.1751.2.18.24.3.1.24	Integer32	read-only	Sustained cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.
I32 viprSubChnlFrMaxBurstSize	1.3.6.1.4.1.1751.2.18.24.3.1.25	Integer32	read-only	Maximum burst size, in cells, this will reflect the frame relay parameters in atm terms.
INT viprSubChnlFlowType	1.3.6.1.4.1.1751.2.18.24.3.1.26	INTEGER	read-write	The type of flow
INT viprSubChnlAdminStatus	1.3.6.1.4.1.1751.2.18.24.3.1.27	INTEGER	read-write	This variable represents the various X.731 states the Sub Channel state machine can take Administartively
INT viprSubChnlOperStatus	1.3.6.1.4.1.1751.2.18.24.3.1.28	INTEGER	read-only	This variable represents the various X.731 states the Sub Channel state machine can take Operationally
I32 viprSubChnlInitTmr	1.3.6.1.4.1.1751.2.18.24.3.1.29	Integer32	read-write	This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.
I32 viprSubChnlDisabWarnTmr	1.3.6.1.4.1.1751.2.18.24.3.1.30	Integer32	read-write	This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.
I32 viprSubChnlShutDwnWarnTmr	1.3.6.1.4.1.1751.2.18.24.3.1.31	Integer32	read-write	This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.
INT viprSubChnlDisableWarning	1.3.6.1.4.1.1751.2.18.24.3.1.32	INTEGER	read-write	This variable when disabled will mask all the Disable warning messages.
INT viprSubChnlDisableReason	1.3.6.1.4.1.1751.2.18.24.3.1.33	INTEGER	read-only	This variable describes the reason why the SubChnl in the unlocked-Disabled state.
ROW viprSubChnlRowStatus	1.3.6.1.4.1.1751.2.18.24.3.1.34	RowStatus	read-write	row status
IP viprSubChnlImIpAddr	1.3.6.1.4.1.1751.2.18.24.3.1.35	IpAddress	read-write	inband management IpAddr
IP viprSubChnlImMask	1.3.6.1.4.1.1751.2.18.24.3.1.36	IpAddress	read-write	inband management Mask
INT viprSubChnlViB	1.3.6.1.4.1.1751.2.18.24.3.1.37	INTEGER	read-write	The viB value of the connection
INT viprSubChnlVUNIB	1.3.6.1.4.1.1751.2.18.24.3.1.38	INTEGER	read-write	The VUNIB value of the connection
INT viprSubChnlTrafficShaping	1.3.6.1.4.1.1751.2.18.24.3.1.39	INTEGER	read-write	Traffic Shaping Support in the A2B direction for outgoing ATM connections.
INT viprSubChnlAtmOamStatus	1.3.6.1.4.1.1751.2.18.24.3.1.40	INTEGER	read-write	Indicates the OAM monitoring status. The 3 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI. End-Seg-Pt: Connection endPoint that is also a segment endPoint.
viprRouteConfigTable	1.3.6.1.4.1.1751.2.18.24.4		not-accessible	Table of Vipr static route Config Information
viprRouteConfigEntry	1.3.6.1.4.1.1751.2.18.24.4.1		not-accessible	Definition for Vipr static route attributes
I32 viprRouteId	1.3.6.1.4.1.1751.2.18.24.4.1.1	Integer32	not-accessible	The unique Id to the routing table entry
IP viprRouteIPAddress	1.3.6.1.4.1.1751.2.18.24.4.1.2	IpAddress	read-write	The IP address of the host/network in the route entry
IP viprRouteIPNetMask	1.3.6.1.4.1.1751.2.18.24.4.1.3	IpAddress	read-write	The IP Subnet Mask for the route entry to identify whether the route entry is a host or network
IP viprRouteDestAddress	1.3.6.1.4.1.1751.2.18.24.4.1.4	IpAddress	read-write	The IP address of the host/network in the route entry
IP viprRouteGatewayAddress	1.3.6.1.4.1.1751.2.18.24.4.1.5	IpAddress	read-write	The IP address of the Gateway
INT viprRouteServiceType	1.3.6.1.4.1.1751.2.18.24.4.1.6	INTEGER	read-write	The Service types that are supported
I32 viprRouteMetric	1.3.6.1.4.1.1751.2.18.24.4.1.7	Integer32	read-write	A scalar value for user-supplied static route metric values.
INT viprRouteAdminStatus	1.3.6.1.4.1.1751.2.18.24.4.1.8	INTEGER	read-write	This variable represents the various X.731 states the Route state machine can take Administratively
INT viprRouteOperStatus	1.3.6.1.4.1.1751.2.18.24.4.1.9	INTEGER	read-only	This variable represents the various X.731 states the Route state machine can take Operationally
I32 viprRouteInitTmr	1.3.6.1.4.1.1751.2.18.24.4.1.10	Integer32	read-write	This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.
I32 viprRouteDisabWarnTmr	1.3.6.1.4.1.1751.2.18.24.4.1.11	Integer32	read-write	This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.
I32 viprRouteShutDwnWarnTmr	1.3.6.1.4.1.1751.2.18.24.4.1.12	Integer32	read-write	This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.
INT viprRouteDisableWarning	1.3.6.1.4.1.1751.2.18.24.4.1.13	INTEGER	read-write	This variable when disabled will mask all the Disable warning messages.
INT viprRouteDisableReason	1.3.6.1.4.1.1751.2.18.24.4.1.14	INTEGER	read-only	This variable describes the reason why the Route in the unlocked-Disabled state.
ROW viprRouteRowStatus	1.3.6.1.4.1.1751.2.18.24.4.1.15	RowStatus	read-write	row status
IP viprRouteDestMask	1.3.6.1.4.1.1751.2.18.24.4.1.16	IpAddress	read-write	The IP Mask of the host/network in the route entry
viprRoutingConfigTable	1.3.6.1.4.1.1751.2.18.24.5		not-accessible	Table of Vipr routes Config Information
viprRoutingConfigEntry	1.3.6.1.4.1.1751.2.18.24.5.1		not-accessible	Definition for Vipr route attributes
INT viprRoutingCommand	1.3.6.1.4.1.1751.2.18.24.5.1.1	INTEGER	not-accessible	The Routing table request command Set to start to initiate the caching of first 15 entries Set to more to initiate the caching of next 15 entries Set to abort to reset the counter in I/O card Set to retrieve in order to get the entries
IP viprRoutingIPAddress	1.3.6.1.4.1.1751.2.18.24.5.1.2	IpAddress	read-only	The IP address of the host/network in the route entry
IP viprRoutingIPNetMask	1.3.6.1.4.1.1751.2.18.24.5.1.3	IpAddress	read-only	The IP Subnet Mask for the route entry to identify whether the route entry is a host or network
IP viprRoutingDestAddress	1.3.6.1.4.1.1751.2.18.24.5.1.4	IpAddress	read-only	The IP address of the host/network in the route entry
IP viprRoutingGatewayAddress	1.3.6.1.4.1.1751.2.18.24.5.1.5	IpAddress	read-only	The IP address of the Gateway
INT viprRoutingServiceType	1.3.6.1.4.1.1751.2.18.24.5.1.6	INTEGER	read-only	The Service types that are supported
INT viprRoutingType	1.3.6.1.4.1.1751.2.18.24.5.1.7	INTEGER	read-only	Route types supported by the RS Card.
I32 viprRoutingMetric	1.3.6.1.4.1.1751.2.18.24.5.1.8	Integer32	read-only	The Path cost
IP viprRoutingDestMask	1.3.6.1.4.1.1751.2.18.24.5.1.9	IpAddress	read-only	The IP address Mask of the host/network in the route entry
I32 viprRoutingAge	1.3.6.1.4.1.1751.2.18.24.5.1.10	Integer32	read-only	Age of the routing entry
I32 viprRoutingIndex	1.3.6.1.4.1.1751.2.18.24.5.1.11	Integer32	not-accessible	Index to the routing entry
viprArpConfigTable	1.3.6.1.4.1.1751.2.18.24.6		not-accessible	Table of Vipr Arp Table Information
viprArpConfigEntry	1.3.6.1.4.1.1751.2.18.24.6.1		not-accessible	Definition for Vipr Arp Table attributes
INT viprArpCommand	1.3.6.1.4.1.1751.2.18.24.6.1.1	INTEGER	not-accessible	The ARP table request command Set to start to initiate the caching of first 15 entries Set to more to initiate the caching of next 15 entries Set to abort to reset the counter in I/O card Set to retrieve in order to get the entries
IP viprArpIPAddress	1.3.6.1.4.1.1751.2.18.24.6.1.2	IpAddress	read-only	The IP address of the host/network
OCT viprArpHwAddress	1.3.6.1.4.1.1751.2.18.24.6.1.3	OCTET STRING	read-only	The hardware address of the host/network
I32 viprArpEntryAge	1.3.6.1.4.1.1751.2.18.24.6.1.4	Integer32	read-only	Age of cache entry.
IP viprArpInterfaceIPAddress	1.3.6.1.4.1.1751.2.18.24.6.1.5	IpAddress	read-only	The Interface IP address through which it is learned
IP viprArpInterfaceIPMask	1.3.6.1.4.1.1751.2.18.24.6.1.6	IpAddress	read-only	The Interface IP address Mask
INT viprArpInterfaceServiceType	1.3.6.1.4.1.1751.2.18.24.6.1.7	INTEGER	read-only	The Service type of the interface through which the ARP table is learned
I32 viprArpIndex	1.3.6.1.4.1.1751.2.18.24.6.1.8	Integer32	not-accessible	The Index to the Arp table
viprPingConfigTable	1.3.6.1.4.1.1751.2.18.24.7		not-accessible	Table of Vipr Ping Table Information
viprPingConfigEntry	1.3.6.1.4.1.1751.2.18.24.7.1		not-accessible	Definition for Vipr Ping Table attributes
IP ipAddr	1.3.6.1.4.1.1751.2.18.24.7.1.1	IpAddress	not-accessible	The IP address of the host/network to be echoed
INT pingStatus	1.3.6.1.4.1.1751.2.18.24.7.1.2	INTEGER	read-only	The response value - Alive/Not Alive
viprRipConfigTable	1.3.6.1.4.1.1751.2.18.24.8		not-accessible	Table of Vipr Rip Update Interval for each card
viprRipConfigEntry	1.3.6.1.4.1.1751.2.18.24.8.1		not-accessible	Definition of Rip Update attributes
INT viprRipUpdateInt	1.3.6.1.4.1.1751.2.18.24.8.1.1	INTEGER	read-write	This variable represents the Rip Update Interval used by the RIP protocol to transmit packets. The unit is in seconds. The default is 30 seconds and user can change it to 8 or 16 seconds for a route server card. The value will apply to all VPN's in a route server card. But different route server cards in different slots can have separate values for Rip Update Interval
toneAnnceControl	1.3.6.1.4.1.1751.2.18.25
INT tasCmprsAnnceId	1.3.6.1.4.1.1751.2.18.25.31	INTEGER	read-write	Announcement ID for this announcement file to be compressed.
INT tasCmprsAnnceReplaceId	1.3.6.1.4.1.1751.2.18.25.32	INTEGER	read-write	Announcement ID of the announcement file to be replaced from the announcement table by this file.
STR tasCmprsAnnceFilename	1.3.6.1.4.1.1751.2.18.25.33	DisplayString	read-write	File name for this announcement which is to be compressed.
STR tasCmprsAnnceDescription	1.3.6.1.4.1.1751.2.18.25.34	DisplayString	read-write	Description for this announcement which is to to be compressed.
INT tasCmprsAnnceCmprsType	1.3.6.1.4.1.1751.2.18.25.35	INTEGER	read-write	The type of compression used for storing this announcement.
INT tasCmprsAnnceType	1.3.6.1.4.1.1751.2.18.25.36	INTEGER	read-write	The type of this announcement.
NUM tasCmprsAnnceIntfIndex	1.3.6.1.4.1.1751.2.18.25.37	IntfIndex	read-write	Interface index in SSPPCCC format of TASM card on which this announcement is to be compressed.
INT tasCmprsAction	1.3.6.1.4.1.1751.2.18.25.38	INTEGER	read-write	Action to be performed on this announcement.
INT tasTstAnnceId	1.3.6.1.4.1.1751.2.18.25.39	INTEGER	read-write	Announcement ID to be played for testing.
NUM tasTstAnnceIntfIndex	1.3.6.1.4.1.1751.2.18.25.40	IntfIndex	read-write	Interface index in SSPPCCC format of CE card on which this announcement is to be played for testing.
INT tasTstAnnceLawType	1.3.6.1.4.1.1751.2.18.25.41	INTEGER	read-write	The type of CE card towards which this announcement is to be played. A-Law is for E1 and U-Law is for DS1
INT tasTstAnnceAction	1.3.6.1.4.1.1751.2.18.25.42	INTEGER	read-write	Action to be performed on this announcement for testing.
I32 tasTstLineId	1.3.6.1.4.1.1751.2.18.25.43	Integer32	read-write	Test ID to be started for line testing.
NUM tasTstLineIntfIndex	1.3.6.1.4.1.1751.2.18.25.44	IntfIndex	read-write	Interface index in SSPPCCC format of CE card on which this test is to be initiated.
INT tasTstLineAction	1.3.6.1.4.1.1751.2.18.25.45	INTEGER	read-write	Test action to be performed.
NUM tasMemIntfIndex	1.3.6.1.4.1.1751.2.18.25.46	IntfIndex	read-write	Interface index in SSPPCCC format of TASM card on which the memory is to be initialised.
INT tasMemAction	1.3.6.1.4.1.1751.2.18.25.47	INTEGER	read-write	Test action to be performed.
IP toneAnnceIpAddress	1.3.6.1.4.1.1751.2.18.25.48	IpAddress	read-write	IP Address for announcement ftp server.
STR toneAnnceAccountName	1.3.6.1.4.1.1751.2.18.25.49	DisplayString	read-write	ftp account name for access to announcement ftp server.
STR toneAnnceAccountPassword	1.3.6.1.4.1.1751.2.18.25.50	DisplayString	read-write	ftp account password for access to announcement ftp server.
STR toneAnnceSourceFile	1.3.6.1.4.1.1751.2.18.25.51	DisplayString	read-write	announcement file with complete path on the ftp server
STR toneAnnceDestinationFile	1.3.6.1.4.1.1751.2.18.25.52	DisplayString	read-write	The announcementSourceFile will be renamed with MS DOS file format and placed in the /scsi/announce directory on the disk.
INT toneAnnceFtpStatus	1.3.6.1.4.1.1751.2.18.25.53	INTEGER	read-only	Current status of the ftp announcement download. Status of the software announcement. noActivity is the initial start state from boot-up. working is set while ftp'ing the announcement. The final state is one of doneSuccessfully, doneWithError, or aborted, all self-explanatory. It will stay in this state until re-boot or starting an announcement. If the state is doneWithError then announcementSwErrorStatus will be set to reflect the type of error.
INT toneAnnceFtpErrorStatus	1.3.6.1.4.1.1751.2.18.25.54	INTEGER	read-only	The result of the finish of the ftp software announcement download. Set to a value 3-21 if announcementSwCopyStatus is doneWithError. Set to none if announcementFtpCopyStatus is doneSuccessfully. Set to userAbort if announcementSwCopyStatus is aborted.
INT toneAnnceFtpAction	1.3.6.1.4.1.1751.2.18.25.55	INTEGER	read-write	start ftp announcement files. When announcementFtpCopyStatus is working, the start request will be ignored. Abort will have effect only when announcementFtpCopystatus is working.
gr303Config	1.3.6.1.4.1.1751.2.18.26
gr303IgConfig	1.3.6.1.4.1.1751.2.18.26.1
gr303IgConfigTable	1.3.6.1.4.1.1751.2.18.26.1.1		not-accessible	Table of GR303 group configuration
gr303IgConfigEntry	1.3.6.1.4.1.1751.2.18.26.1.1.1		not-accessible	Row definition for GR303 group configuration
INT gr303IgId	1.3.6.1.4.1.1751.2.18.26.1.1.1.1	INTEGER	not-accessible	This is used as an index into GR303IG table which recognizes GR303 Interface Group
ROW gr303IgRowStatus	1.3.6.1.4.1.1751.2.18.26.1.1.1.2	RowStatus	read-write	GR303IG config entry row status
INT gr303IgAdminStatus	1.3.6.1.4.1.1751.2.18.26.1.1.1.3	INTEGER	read-write	Administrative status of the GR303IG
NUM gr303IgPrimaryTMCChanIntfId	1.3.6.1.4.1.1751.2.18.26.1.1.1.4	IntfIndex	read-write	Primary TMC channel Interface Id in SSPPCCC format
NUM gr303IgPrimaryEOCChanIntfId	1.3.6.1.4.1.1751.2.18.26.1.1.1.5	IntfIndex	read-write	Primary EOC channel Interface Id in SSPPCCC format
NUM gr303IgBackupTMCChanIntfId	1.3.6.1.4.1.1751.2.18.26.1.1.1.6	IntfIndex	read-write	Backup TMC channel Interface Id in SSPPCCC format
NUM gr303IgBackupEOCChanIntfId	1.3.6.1.4.1.1751.2.18.26.1.1.1.7	IntfIndex	read-write	Backup EOC channel Interface Id in SSPPCCC format
INT gr303IgPrimaryTMCStatus	1.3.6.1.4.1.1751.2.18.26.1.1.1.8	INTEGER	read-only	Primary TMC channel Status
INT gr303IgPrimaryEOCStatus	1.3.6.1.4.1.1751.2.18.26.1.1.1.9	INTEGER	read-only	Primary EOC channel Status
INT gr303IgBackupTMCStatus	1.3.6.1.4.1.1751.2.18.26.1.1.1.10	INTEGER	read-only	Backup TMC channel Status.Value null(5) Indicates that the Backup TMC has not been configured.
INT gr303IgBackupEOCStatus	1.3.6.1.4.1.1751.2.18.26.1.1.1.11	INTEGER	read-only	Backup EOC channel Status.Value null(5) Indicates that the Backup EOC has not been configured.
INT gr303IgTMCProtSwitchProvState	1.3.6.1.4.1.1751.2.18.26.1.1.1.12	INTEGER	read-write	Lock/Unlock the protection switch
INT gr303IgEOCProtSwitchProvState	1.3.6.1.4.1.1751.2.18.26.1.1.1.13	INTEGER	read-write	Lock/Unlock the protection switch
INT gr303IgTMCProtSwitchCommand	1.3.6.1.4.1.1751.2.18.26.1.1.1.14	INTEGER	read-write	User command to do path protection switch
INT gr303IgEOCProtSwitchCommand	1.3.6.1.4.1.1751.2.18.26.1.1.1.15	INTEGER	read-write	User command to do path protection switch
INT gr303IgLocalDigitalSwitchType	1.3.6.1.4.1.1751.2.18.26.1.1.1.16	INTEGER	read-write	LDS (IDT) type
INT gr303IgLocalDigitalSwitchVersion	1.3.6.1.4.1.1751.2.18.26.1.1.1.17	INTEGER	read-write	LDS (IDT)Version
gr303IgIntfConfigTable	1.3.6.1.4.1.1751.2.18.26.1.2		not-accessible	Table of interface attributes in an GR303IG
gr303IgIntfConfigEntry	1.3.6.1.4.1.1751.2.18.26.1.2.1		not-accessible	Row definition for GR303 Access Arrangement Interface configuration
INT gr303IntfIgId	1.3.6.1.4.1.1751.2.18.26.1.2.1.1	INTEGER	not-accessible	This is used as an index into GR303Ig table which recognizes GR303 Interface Group. This is used as a first index into this interface table.
INT gr303IgIntfId	1.3.6.1.4.1.1751.2.18.26.1.2.1.2	INTEGER	not-accessible	This is used as an index into IG interface table which recognizes GR303 Ig interfaces. This is used as a second index into this table
I32 gr303IgIntfPhysId	1.3.6.1.4.1.1751.2.18.26.1.2.1.3	Integer32	read-write	Interface's Physical ID (SSPPCCC)
I32 gr303IgIntfNetId	1.3.6.1.4.1.1751.2.18.26.1.2.1.4	Integer32	read-only	gr303Ig Interface (DS1) Net Id assigned by the network
ROW gr303IgIntfRowStatus	1.3.6.1.4.1.1751.2.18.26.1.2.1.5	RowStatus	read-write	GR303IG interface entry row status - row status can not be made active until all the values are set
gr303LapdConfigTable	1.3.6.1.4.1.1751.2.18.26.1.4		not-accessible	Table of LAPD attributes in an GR303IG
gr303LapdConfigEntry	1.3.6.1.4.1.1751.2.18.26.1.4.1		not-accessible	Row definition for LAPD attributes in a GR303IG
INT gr303LapdIgId	1.3.6.1.4.1.1751.2.18.26.1.4.1.1	INTEGER	not-accessible	GR303IG Number index which recognizes GR303 Interface group
INT gr303T200	1.3.6.1.4.1.1751.2.18.26.1.4.1.2	INTEGER	read-write	value of Lapd T200 timer in miliseconds in step size of 50 ms
INT gr303T203	1.3.6.1.4.1.1751.2.18.26.1.4.1.3	INTEGER	read-write	value of Lapd T203 timer in seconds
INT gr303N200	1.3.6.1.4.1.1751.2.18.26.1.4.1.4	INTEGER	read-write	Maximum number of retransmissions
INT gr303K	1.3.6.1.4.1.1751.2.18.26.1.4.1.5	INTEGER	read-write	Maximum number of outstanding I frames - Lapd - window size.
gr303TMCConfigTable	1.3.6.1.4.1.1751.2.18.26.1.5		not-accessible	Table of Layer 3 attributes in an GR303IG
gr303TMCConfigEntry	1.3.6.1.4.1.1751.2.18.26.1.5.1		not-accessible	Row definition for GR303 Access Arrangement Layer3 parameters configuration
INT gr303TMCIgId	1.3.6.1.4.1.1751.2.18.26.1.5.1.1	INTEGER	not-accessible	GR303IG Number index which recognizes GR303 Interface group
INT gr303TMCT303	1.3.6.1.4.1.1751.2.18.26.1.5.1.2	INTEGER	read-write	value of TMC T303 timer in miliseconds with a step size of 500 ms
INT gr303TMCT396	1.3.6.1.4.1.1751.2.18.26.1.5.1.3	INTEGER	read-write	value of TMC T396 timer in miliseconds with a step size of 1000 ms
gr303Stats	1.3.6.1.4.1.1751.2.18.27
gr303IgStats	1.3.6.1.4.1.1751.2.18.27.1
gr303IgStatsTable	1.3.6.1.4.1.1751.2.18.27.1.1		not-accessible	Table of GR303 GR303IG based stats attributes
gr303IgStatsEntry	1.3.6.1.4.1.1751.2.18.27.1.1.1		not-accessible	Row definition for GR303 GR303IG based stats
INT gr303IgStatsIgId	1.3.6.1.4.1.1751.2.18.27.1.1.1.1	INTEGER	not-accessible	This is used as an index into GR303 Ig table which recognizes GR303 Interface Group Interface group
I32 gr303IgStatsCurrentInCalls	1.3.6.1.4.1.1751.2.18.27.1.1.1.2	Integer32	read-only	Total number of Currently established incoming calls
I32 gr303IgStatsCurrentOutCalls	1.3.6.1.4.1.1751.2.18.27.1.1.1.3	Integer32	read-only	Total number of Currently established outgoing calls
I32 gr303IgStatsOutCallSuccessful	1.3.6.1.4.1.1751.2.18.27.1.1.1.4	Integer32	read-only	Total number successful outgoing calls
I32 gr303IgStatsOutCallFailed	1.3.6.1.4.1.1751.2.18.27.1.1.1.5	Integer32	read-only	Total number of Failed outgoing calls
I32 gr303IgStatsInCallSuccessful	1.3.6.1.4.1.1751.2.18.27.1.1.1.6	Integer32	read-only	Total number successful incoming calls
I32 gr303IgStatsInCallFailed	1.3.6.1.4.1.1751.2.18.27.1.1.1.7	Integer32	read-only	Total number of Failed incoming calls
INT gr303IgStatsReset	1.3.6.1.4.1.1751.2.18.27.1.1.1.8	INTEGER	read-write	gr303Ig reset statistics button
atmTrunkingMIBObjects	1.3.6.1.4.1.1751.2.18.28
atmTrunkingIWFBaseGroup	1.3.6.1.4.1.1751.2.18.28.1
I32 atmTrunkingIWFIdentifier	1.3.6.1.4.1.1751.2.18.28.1.1	Integer32	read-write	IWF ID for the local endpoint
OCT atmTrunkingIWFLocalAddress	1.3.6.1.4.1.1751.2.18.28.1.2	OCTET STRING	read-write	IWF ATM address for the local endpoint
I32 atmTrunkingIWFMaxRemoteIWF	1.3.6.1.4.1.1751.2.18.28.1.3	Integer32	read-write	Maximum remote IWF that can connect to this endpoint
INT atmTrunkingIWFAdminStatus	1.3.6.1.4.1.1751.2.18.28.1.4	INTEGER	read-write	Indicates whether the Local IWF is active or not
atmTrunkingRemoteIWFTable	1.3.6.1.4.1.1751.2.18.28.2		not-accessible	Remote IWF table
atmTrunkingRemoteIWFEntry	1.3.6.1.4.1.1751.2.18.28.2.1		not-accessible	Entry in atmTrunkingRemoteIWFTable
I32 atmTrunkingRemoteIWFIdentifier	1.3.6.1.4.1.1751.2.18.28.2.1.1	Integer32	not-accessible	IWF ID for the remote IWF
OCT atmTrunkingRemoteIWFAddress	1.3.6.1.4.1.1751.2.18.28.2.1.2	OCTET STRING	read-create	IWF ATM address for the remote IWF
INT atmTrunkingRemoteIWFTrnkMode	1.3.6.1.4.1.1751.2.18.28.2.1.3	INTEGER	read-create	Maximum remote IWF that can connect to this endpoint
INT atmTrunkingRemoteIWFAdminStatus	1.3.6.1.4.1.1751.2.18.28.2.1.4	INTEGER	read-create	Indicates whether the Local IWF is active or not
ROW atmTrunkingRemoteIWFRowStatus	1.3.6.1.4.1.1751.2.18.28.2.1.5	RowStatus	read-create	Maximum remote IWF that can connect to this endpoint
atmTrunkingSigVccTable	1.3.6.1.4.1.1751.2.18.28.3		not-accessible	Table of iwf signaling vcc configuration entities
atmTrunkingSigVccEntry	1.3.6.1.4.1.1751.2.18.28.3.1		not-accessible	Entry in atmTrunkingSigVccTable
I32 atmTrunkingSigVccRmtIWFIdentifier	1.3.6.1.4.1.1751.2.18.28.3.1.1	Integer32	not-accessible	IWF ID for the remote IWF
INT atmTrunkingSigVccIdentifier	1.3.6.1.4.1.1751.2.18.28.3.1.2	INTEGER	not-accessible	Vcc ID assigned by the owner of this signaling Vcc
NUM atmTrunkingSigVccOutgoingIfIndex	1.3.6.1.4.1.1751.2.18.28.3.1.3	IntfIndex	read-create	Intf index of the outgoing interface,readonly for SVC/SPVC
INT atmTrunkingSigVccOutgoingVpi	1.3.6.1.4.1.1751.2.18.28.3.1.4	INTEGER	read-create	VPI used at the outgoing interface, readonly for SVC/SPVC
INT atmTrunkingSigVccOutgoingVci	1.3.6.1.4.1.1751.2.18.28.3.1.5	INTEGER	read-create	VCI used at the outgoing interface, readonly for SVC/SPVC
INT atmTrunkingSigVccOwner	1.3.6.1.4.1.1751.2.18.28.3.1.6	INTEGER	read-create	Indicates who is the owner of the Sig VCC
I32 atmTrunkingSigVccInactiveTimer	1.3.6.1.4.1.1751.2.18.28.3.1.7	Integer32	read-create	Inactive time period on which to clear the call
INT atmTrunkingSigVccType	1.3.6.1.4.1.1751.2.18.28.3.1.8	INTEGER	read-create	Indicates if the SigVcc should be setup as PVC/SPVC/SVC
INT atmTrunkingSigVccSignaling	1.3.6.1.4.1.1751.2.18.28.3.1.9	INTEGER	read-create	Indicates the signalling protocol used between the IWFs
I32 atmTrunkingSigVccFwPcr01	1.3.6.1.4.1.1751.2.18.28.3.1.10	Integer32	read-create	Forward PCR for the call
I32 atmTrunkingSigVccBwPcr01	1.3.6.1.4.1.1751.2.18.28.3.1.11	Integer32	read-create	Backward PCR for the call
I32 atmTrunkingSigVccFwScr01	1.3.6.1.4.1.1751.2.18.28.3.1.12	Integer32	read-create	Forward SCR for the call
I32 atmTrunkingSigVccBwScr01	1.3.6.1.4.1.1751.2.18.28.3.1.13	Integer32	read-create	Backward SCR for the call
I32 atmTrunkingSigVccFwMbs01	1.3.6.1.4.1.1751.2.18.28.3.1.14	Integer32	read-create	Forward MBS for the call
I32 atmTrunkingSigVccBwMbs01	1.3.6.1.4.1.1751.2.18.28.3.1.15	Integer32	read-create	Backward MBS for the call
I32 atmTrunkingSigVccMaxAal2Vcc	1.3.6.1.4.1.1751.2.18.28.3.1.16	Integer32	read-create	Maximum number of bearer VCCs controlled by this SigVcc
I32 atmTrunkingSigVccActiveAal2Vcc	1.3.6.1.4.1.1751.2.18.28.3.1.17	Integer32	read-only	Number of active bearer VCCs controlled by this SigVcc
INT atmTrunkingSigVccOperStatus	1.3.6.1.4.1.1751.2.18.28.3.1.18	INTEGER	read-only	Indicates whether the Local IWF is active or not
ROW atmTrunkingSigVccRowStatus	1.3.6.1.4.1.1751.2.18.28.3.1.19	RowStatus	read-create	Row status
INT atmTrunkingSigVccViB	1.3.6.1.4.1.1751.2.18.28.3.1.20	INTEGER	read-create	VI to associate the Egress part of A2B connection
INT atmTrunkingSigVccVUNIB	1.3.6.1.4.1.1751.2.18.28.3.1.21	INTEGER	read-create	VUNI associated the Egress part of A2B connection
I32 atmTrunkingSigVccRetryTimer	1.3.6.1.4.1.1751.2.18.28.3.1.22	Integer32	read-create	the time(seconds) to wait before attempting to establish the ATM Trunking Signalling VCC SPVC after previous failed call attempt. 0 indicates retries will be attempted immedi ately
I32 atmTrunkingSigVccRetryLimit	1.3.6.1.4.1.1751.2.18.28.3.1.23	Integer32	read-create	ATM Trunking Signalling VCC SPVC Retry Limit. 0 indicates unlimited
INT atmTrunkingSigVccRestart	1.3.6.1.4.1.1751.2.18.28.3.1.24	INTEGER	read-write	The active ATM Trunking SPVC is released, if necessary, and a new setup procedure is begun if restart, otherwise, noop.
INT atmTrunkingSigVccPriority	1.3.6.1.4.1.1751.2.18.28.3.1.25	INTEGER	read-write	Priority of TrunkingSigVcc - priority-1 being highest priority .
I32 atmTrunkingSigVccRetryCounter	1.3.6.1.4.1.1751.2.18.28.3.1.26	Integer32	read-only	Indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the SigVcc SPVC is restarted.
atmTrunkingBrVccConfigTable	1.3.6.1.4.1.1751.2.18.28.4		not-accessible	Table of iwf aal2 bearer vcci configuration entities
atmTrunkingBrVccConfigEntry	1.3.6.1.4.1.1751.2.18.28.4.1		not-accessible	Row definition for iwf aal2 vcci configuration
I32 atmTrunkingBrVccRmtIWFId	1.3.6.1.4.1.1751.2.18.28.4.1.1	Integer32	not-accessible	IWF ID for the remote IWF
INT atmTrunkingBrVccSigVccId	1.3.6.1.4.1.1751.2.18.28.4.1.2	INTEGER	read-only	Signalling Vcc associated with this Br Vcc
INT atmTrunkingBrVccId	1.3.6.1.4.1.1751.2.18.28.4.1.3	INTEGER	not-accessible	Id of the AAL2 Bear Vcc
NUM atmTrunkingBrVccIf	1.3.6.1.4.1.1751.2.18.28.4.1.4	IntfIndex	read-create	Intf index of the outgoing interface, readonly for SVC/SPVC
INT atmTrunkingBrVccVpi	1.3.6.1.4.1.1751.2.18.28.4.1.5	INTEGER	read-create	VPI value of this VCC connection. Valid range is a number between 0 and 4095.
INT atmTrunkingBrVccVci	1.3.6.1.4.1.1751.2.18.28.4.1.6	INTEGER	read-create	VCI value of this VCC connection. Valid range is a number between 0 and 65535.
INT atmTrunkingBrVccViB	1.3.6.1.4.1.1751.2.18.28.4.1.7	INTEGER	read-create	VI to associate the Egress part of A2B connection
INT atmTrunkingBrVccVUNIB	1.3.6.1.4.1.1751.2.18.28.4.1.8	INTEGER	read-create	VUNI associated the Egress part of A2B connection
INT atmTrunkingBrVccServiceType	1.3.6.1.4.1.1751.2.18.28.4.1.9	INTEGER	read-create	service type
INT atmTrunkingBrVccSarType	1.3.6.1.4.1.1751.2.18.28.4.1.10	INTEGER	read-create	sar type
INT atmTrunkingBrVccOwner	1.3.6.1.4.1.1751.2.18.28.4.1.11	INTEGER	read-create	The owner of this Vcc
INT atmTrunkingBrVccOperStatus	1.3.6.1.4.1.1751.2.18.28.4.1.12	INTEGER	read-only	The Operational Status of this Bearer Vcc
I32 atmTrunkingBrVccFwAtmPcr01	1.3.6.1.4.1.1751.2.18.28.4.1.13	Integer32	read-create	Forward pcr (0+1)
I32 atmTrunkingBrVccBwAtmPcr01	1.3.6.1.4.1.1751.2.18.28.4.1.14	Integer32	read-create	Backward pcr (0+1)
I32 atmTrunkingBrVccFwAtmScr01	1.3.6.1.4.1.1751.2.18.28.4.1.15	Integer32	read-create	Forward scr (0+1)
I32 atmTrunkingBrVccBwAtmScr01	1.3.6.1.4.1.1751.2.18.28.4.1.16	Integer32	read-create	Backward scr (0+1)
I32 atmTrunkingBrVccFwAtmMbs01	1.3.6.1.4.1.1751.2.18.28.4.1.17	Integer32	read-create	Forward Mbs (0+1)
I32 atmTrunkingBrVccBwAtmMbs01	1.3.6.1.4.1.1751.2.18.28.4.1.18	Integer32	read-create	Backward Mbs (0+1)
INT atmTrunkingBrVccConnType	1.3.6.1.4.1.1751.2.18.28.4.1.19	INTEGER	read-create	connection type
I32 atmTrunkingBrVccActiveChanCnt	1.3.6.1.4.1.1751.2.18.28.4.1.20	Integer32	read-only	Number of currently active channels in this Vcc
INT atmTrunkingBrVccMaxAal2ChanId	1.3.6.1.4.1.1751.2.18.28.4.1.21	INTEGER	read-create	Max Id of channels supported within this br vcc
INT atmTrunkingBrVccCircuitModeDataSupp	1.3.6.1.4.1.1751.2.18.28.4.1.22	INTEGER	read-create	Circuit mode data
INT atmTrunkingBrVccFrameModeSupp	1.3.6.1.4.1.1751.2.18.28.4.1.23	INTEGER	read-create	Frame mode data
INT atmTrunkingBrVccFaxModSupp	1.3.6.1.4.1.1751.2.18.28.4.1.24	INTEGER	read-create	FAX Demodulation
INT atmTrunkingBrVccCASPktXportSupp	1.3.6.1.4.1.1751.2.18.28.4.1.25	INTEGER	read-create	Channel Associated Signaling
INT atmTrunkingBrVccDTMFPktXportSupp	1.3.6.1.4.1.1751.2.18.28.4.1.26	INTEGER	read-create	DTMF Dialed Digits
INT atmTrunkingBrVccMFR1PktXportSupp	1.3.6.1.4.1.1751.2.18.28.4.1.27	INTEGER	read-create	MF-R1 Dialed Digits
INT atmTrunkingBrVccMFR2PktXportSupp	1.3.6.1.4.1.1751.2.18.28.4.1.28	INTEGER	read-create	MF-R2 Dialed Digits
INT atmTrunkingBrVccPCMEncoding	1.3.6.1.4.1.1751.2.18.28.4.1.29	INTEGER	read-create	DTMF Dialed Digits
INT atmTrunkingBrVccMaxFrameLength	1.3.6.1.4.1.1751.2.18.28.4.1.30	INTEGER	read-create	Maximum length of frame mode data
INT atmTrunkingBrVccIdleChannSuprSupp	1.3.6.1.4.1.1751.2.18.28.4.1.31	INTEGER	read-create	Idle Channel Supression
INT atmTrunkingBrVccSilenceDetSupp	1.3.6.1.4.1.1751.2.18.28.4.1.32	INTEGER	read-create	Silence Detection
INT atmTrunkingBrVccCompressionSpec	1.3.6.1.4.1.1751.2.18.28.4.1.33	INTEGER	read-create	Compression Type

INT tasTrapTstId

1.3.6.1.4.1.1751.2.18.15.51

INTEGER

read-only

Announcement ID for trap.

INT tasTrapAnnceId

1.3.6.1.4.1.1751.2.18.15.52

INTEGER

read-only

test id for trap.

INT atmVpi

1.3.6.1.4.1.1751.2.18.15.53

INTEGER

read-only

Vpi is used in identification of Traps

INT atmVci

1.3.6.1.4.1.1751.2.18.15.54

INTEGER

read-only

Vci is used in identification of Traps

INT iptResultCode

1.3.6.1.4.1.1751.2.18.15.55

INTEGER

read-only

Various result codes for the operator's command forsetting/deleting interface protection group. interfaceProtectioniptAlreadyExistInterface: Expect another interface to be protected. interfaceProtectioniptInvalidInterface:interface invalid interfaceProtectioniptInvalidParams: invalid Parameters interfaceProtectioniptTryToDeleteEmptyTable:Table is already empty,can not be deleted . interfaceProtectioniptInvalidConfiguation: interfaceProtectioniptSuccessfulSwichOver: interface is switched over to the secondry interface. interfaceProtectioniptSuccessfulSwichBack: interface is switched back from secondry interface. interfaceProtectioniptFailedSwichOver: interface is failed switched over to the secondry interface. interfaceProtectioniptFailedSwichBack: interface is failed switched back from secondry interface.

INT pgtResultCode

1.3.6.1.4.1.1751.2.18.15.56

INTEGER

read-only

Various result codes for the operator's command for interface protection .

INT tasmControlBlockAllocFailReasonCode

1.3.6.1.4.1.1751.2.18.15.57

INTEGER

read-only

The result of a tasm control block memory allocation request.

INT tasmCacheMemAllocFailReasonCode

1.3.6.1.4.1.1751.2.18.15.58

INTEGER

read-only

The result of a tasm control block memory allocation request.

INT atmTrunkingConfigFailureCode

1.3.6.1.4.1.1751.2.18.15.59

INTEGER

read-only

An identified reason for failure while configuring/modifying ATM Trunking parameters: localIWFAlreadyConfigured(1) : Local IWF has already been configured, the parameters can not be changed or apply again. localIWFAtmAddressError(2): the ATM Address for Local IWF is not valid or this address has been used by someone else. localIWFIdOutOfRange(3): the Identification of Local IWF is out of range. maxNumberRmtIWFOutOfRange(4): the maximum number of Remote IWF is out of range. rmtIWFAlreadyConfigured(5): this remote IWF has already been configured( with index atmTrunkingRmtIWFIdentifier). rmtIWFIdOutOfRange: the identifier for the remote IWF is out of range. rmtIWFAtmAddressError: the ATM Address for remote IWF is not valid or this address has been used by someone else. vccIdError: the VCC ID for the SigVcc or BrVcc is 0, or this VCC ID is out of range or it has been used by someone else. vccPvcParameterNotAcceptable: the parameters of PVC side, including slot, port, channel, vpi, vci, are not acceptable. vccTrafficParameterNotValid: the VCC traffic parameters are not acceptable, including FwPcr01, BwPcr01, FwScr01, BwScr01, FWMbs01, BwMbs01, BrVccServiceType, BrVccSarType. vccViVuniNotValid: the configuration of Egress Vi/VUNI is not acceptable. vccTrunkParameterNotValid: the parameters for the Trunk is not supported, including BrVccMaxAal2ChanId, BrVccCircuitModeDataSupp, BrVccFrameModeSupp, BrVccFaxModeSupp, CASPktXportSupp, BrVccDTMFPktXportSupp, BrVccMFR1PktXportSupp, BrVccMFR2PktXportSupp, BrVccPCMEncoding, BrVccMaxFrameLength, BrVccIdleChannSuprSupp, BrVccSilenceDetSupp, BrVccCompressionSpec,AudioProfileId, SigVccSignaling. vccTrunkFeatureParameterNotValid: PSAX proprietary feature parameters not supported including SigVccInactiveTimer, SigVccRetryTimer, SigVccRetryLimit, BrVccInactiveTimer, BrVccRetryTimer, BrVccRetryLimit, BrVccGr303Supp, BrVccOamStatus. localIwfNotConfigured(14) : Local IWF not Configured localIwfIdNotMatch(15): specified Local IWF not match localIwfStatus(16): this operation is not supported because of the status of Local IWF rmtIwfNotConfigured(17): Remote IWF Not Configured rmtIwfModeNotCompatible(18): the Mode of Remote IWF is not compatiable rmtIwfStatus(19): this operation is not support because of the Status of Remote IWF vccAlreadyConfigured(20): This VCC has been configured vccPvcCacReject(21): PVC Configuration rejected by Cac Reservation Function requiredFieldMissing(22): mandatory fields missing outOfResource(23): Atm Trunking Task or System out of resource for this configuration rowStatusError(24):Row Status Error with the SNMP command generalErrorUnspecified(25): all other unspecified failure cause.

INT sapphireIntfAddressFailReasonCode

1.3.6.1.4.1.1751.2.18.15.60

INTEGER

read-only

The result of assigning the Sapphire Interface address when PSAX is Sapphire client. address-ok(1), Address assignment succeeded fail-Ilegal-IP-address(2), Illegal IP address assigned address not matching fail-not-match-InBandManagement-Switch-CPU-IP-Address(3) In-Band Management IP or Switch IP or CPU IP address fail-Switch-or-CPU-IP-Address-unconfigured(4) Switch IP or CPU IP address unconfigured fail-InBandManagement-IP-Address-unconfigured(5) InBandManagement IP address unconfigured.

INT chassisOverTempAlarmReasonCode

1.3.6.1.4.1.1751.2.18.15.61

INTEGER

read-only

Indicator of presence of chassis over temperature alarm.

sysControl

1.3.6.1.4.1.1751.2.18.16

INT saveConfiguration

1.3.6.1.4.1.1751.2.18.16.1

INTEGER

read-write

save configuration

INT upgradeSoftware

1.3.6.1.4.1.1751.2.18.16.2

INTEGER

read-write

software load management

NUM purgePvcConnections

1.3.6.1.4.1.1751.2.18.16.3

IntfIndex

read-write

purge PVC connections on indicated interface

INT purgeRoutingTable

1.3.6.1.4.1.1751.2.18.16.4

INTEGER

read-write

purge indicated routing table

I32 resetPortStatistics

1.3.6.1.4.1.1751.2.18.16.5

Integer32

read-write

Reset the statistics counters for the given port Id (SSPP)

NUM resetInterfaceStatistics

1.3.6.1.4.1.1751.2.18.16.6

IntfIndex

read-write

Reset the interface counters for the given port Id (SSPPCCC)

I32 resetAllStatistics

1.3.6.1.4.1.1751.2.18.16.7

Integer32

read-write

Reset all port and interface statistics counters, accpets any integer value

IP upgradeIpAddress

1.3.6.1.4.1.1751.2.18.16.8

IpAddress

read-write

IP Address for upgrade ftp server.

STR upgradeAccountName

1.3.6.1.4.1.1751.2.18.16.9

DisplayString

read-write

ftp account name for access to upgrade ftp server.

STR upgradeAccountPassword

1.3.6.1.4.1.1751.2.18.16.10

DisplayString

read-write

ftp account password for access to upgrade ftp server.

STR upgradeCdromFile

1.3.6.1.4.1.1751.2.18.16.11

DisplayString

read-write

cdrom file path on upgrade ftp server to upgrade image library.

STR upgradeLicenseKey

1.3.6.1.4.1.1751.2.18.16.12

DisplayString

read-write

software license key.

INT upgradeSwCopyStatus

1.3.6.1.4.1.1751.2.18.16.13

INTEGER

read-only

Current status of the ftp software upgrade download. Status of the software upgrade. noActivity is the initial start state from boot-up. working is set while ftp'ing the upgrade. The final state is one of doneSuccessfully, doneWithError, or aborted, all self-explanatory. It will stay in this state until re-boot or starting an upgrade. If the state is doneWithError then upgradeSwErrorStatus will be set to reflect the type of error.

INT upgradeSwErrorStatus

1.3.6.1.4.1.1751.2.18.16.14

INTEGER

read-only

The result of the finish of the ftp software upgrade download. Set to a value 3-22 if upgradeSwCopyStatus is doneWithError. Set to none if upgradeSwCopyStatus is doneSuccessfully. Set to userAbort if upgradeSwCopyStatus is aborted.

INT systemSwCopy

1.3.6.1.4.1.1751.2.18.16.15

INTEGER

read-write

start copy system files according to the profile. When upgradeSwCopyStatus is working, the start request will be ignored. Abort will have effect only when upgradeSwCopystatus is working.

fwReleaseTable

1.3.6.1.4.1.1751.2.18.16.16

not-accessible

Table of firmware inventory data

fwReleaseEntry

1.3.6.1.4.1.1751.2.18.16.16.1

not-accessible

Row definition for firmware inventory

INT fwReleaseSlot

1.3.6.1.4.1.1751.2.18.16.16.1.1

INTEGER

not-accessible

Physical slot location. Valid range is a number between 1 and 16.

OCT fwReleaseRunning

1.3.6.1.4.1.1751.2.18.16.16.1.2

OCTET STRING

read-only

the firmware release currently running in a physical slot (e.g., 01.03.C01).

OCT fwReleaseEpromVersion

1.3.6.1.4.1.1751.2.18.16.16.1.3

OCTET STRING

read-only

the version of the firmware located on the I/O card (e.g., 01.03.C01).

OCT fwReleaseCurrentVersion

1.3.6.1.4.1.1751.2.18.16.16.1.4

OCTET STRING

read-only

the version of the firmware located in /scsi/current/io on the CPU disk drive (e.g., 01.03.C01).

OCT fwReleaseNextVersion

1.3.6.1.4.1.1751.2.18.16.16.1.5

OCTET STRING

read-only

the version of the firmware located in /scsi/next/io on the CPU disk drive (e.g., 01.03.C01).

INT fwReleaseUpdate

1.3.6.1.4.1.1751.2.18.16.16.1.6

INTEGER

read-write

Update the fwReleaseCurrentVersion and the fwReleaseNextVersion variables by remapping the firmware files from the CPU disk drive.

INT fwReleaseUpgrade

1.3.6.1.4.1.1751.2.18.16.16.1.7

INTEGER

read-write

Update the fwReleaseCurrentVersion and the fwReleaseNextVersion variables by remapping the firmware files from the CPU disk drive.

I32 resetBridgeDomainStatistics

1.3.6.1.4.1.1751.2.18.16.17

Integer32

read-write

Resets bridge domain statistics.

INT remoteRebootCommand

1.3.6.1.4.1.1751.2.18.16.18

INTEGER

read-write

type of reboot.

I32 resetFrLmiStatistics

1.3.6.1.4.1.1751.2.18.16.19

Integer32

read-write

Reset the frame relay LMI statistics counters for the given port Id (SSPPCCC)

INT removeConfigurationFiles

1.3.6.1.4.1.1751.2.18.16.20

INTEGER

read-write

Removes the user configuration/connection files from the hard disk on the cpu.

INT systemFilesDirtyBitStatus

1.3.6.1.4.1.1751.2.18.16.21

INTEGER

read-only

Bit mask for system files: 0: all are clean 1: console.def 2: ecd.def 4: ssid.def 8: cnctn.db 16: iisp.cbr 32: iisp.vbr 64: spvc.db 128: vipr.cfg 256: fwc.def 512: vi.db 1024: iproute.db 2048: atmvuni.db

I32 resetAtmIlmiStatistics

1.3.6.1.4.1.1751.2.18.16.22

Integer32

read-write

Reset the ATM ILMI statistics counters for the given channel Id (SSPPCCC)

NUM resetImaGrpChannelStatistics

1.3.6.1.4.1.1751.2.18.16.23

IntfIndex

read-write

Reset the IMA Group Statistics counters for the given port Id (SSPPCCC)

I32 oc3APSResetStats

1.3.6.1.4.1.1751.2.18.16.24

Integer32

read-write

Reset the oc3aps Group Statistics counters for the given port Id (SSPP)

I32 resetsonetSectionStatistics

1.3.6.1.4.1.1751.2.18.16.25

Integer32

read-write

Reset the sonetSectionCurrent Statistics counters for the given port Id (SSPP)

I32 resetsonetLineStatistics

1.3.6.1.4.1.1751.2.18.16.26

Integer32

read-write

Reset the sonetLineCurrent Statistics counters for the given port Id (SSPP)

I32 resetsonetVTPathStatistics

1.3.6.1.4.1.1751.2.18.16.27

Integer32

read-write

Reset the sonetVTPathCurrent Statistics counters for the given port Id (SSPP)

I32 viprVpnReset

1.3.6.1.4.1.1751.2.18.16.28

Integer32

read-write

Reset the VPN statistics for VPN specified by (SSVV)

INT svcRetBackupStatus

1.3.6.1.4.1.1751.2.18.16.29

INTEGER

read-only

Indicates backup status wrt SVC retention

I32 resetsonetPathStatistics

1.3.6.1.4.1.1751.2.18.16.30

Integer32

read-write

Reset the sonetPathCurrent Statistics counters for the given port Id (SSPP)

I32 ambientTemperature

1.3.6.1.4.1.1751.2.18.16.31

Integer32

read-only

Ambient temperature in degree Celcius where the system is kept

remoteDbServerGroup

1.3.6.1.4.1.1751.2.18.16.32

IP remoteDbServerIpAddress

1.3.6.1.4.1.1751.2.18.16.32.1

IpAddress

read-write

IP Address for remote database server.

STR remoteDbServerLogin

1.3.6.1.4.1.1751.2.18.16.32.2

DisplayString

read-write

ftp account name for remote database server.

STR remoteDbServerPassword

1.3.6.1.4.1.1751.2.18.16.32.3

DisplayString

read-write

ftp account password for remote database server.

STR remoteDbServerDirectory

1.3.6.1.4.1.1751.2.18.16.32.4

DisplayString

read-write

directory on remote database server where to save/restore database files from.

INT remoteDbCommand

1.3.6.1.4.1.1751.2.18.16.32.5

INTEGER

read-write

remote database operation.

INT remoteDbOperationStatus

1.3.6.1.4.1.1751.2.18.16.32.6

INTEGER

read-only

Current status of remote database command.

INT remoteDbOperationErrorStatus

1.3.6.1.4.1.1751.2.18.16.32.7

INTEGER

read-only

The result at the finish of remote database operation.

stratumConfig

1.3.6.1.4.1.1751.2.18.17

INT stratumSyncSource

1.3.6.1.4.1.1751.2.18.17.1

INTEGER

read-write

Clock source for the stratum card - lineTiming: must have slot and port specified in stratumPrimaryLineId. compositeClock: local clock must be available.

I32 stratumPrimaryLineId

1.3.6.1.4.1.1751.2.18.17.2

Integer32

read-write

Format SSPP (slot and port #'s) to be used when lineTiming is specified in stratumSyncSource.

I32 stratumSecondaryLineId

1.3.6.1.4.1.1751.2.18.17.3

Integer32

read-write

Format SSPP (slot and port #'s) to be used if the primary line has failed. Zeros imply that the stratum should switch to holdover mode instead.

INT stratumLevel

1.3.6.1.4.1.1751.2.18.17.4

INTEGER

read-write

Enable or disable the switching over to stratum 4 when stratum 3 is not possible.

INT stratumLineCommand

1.3.6.1.4.1.1751.2.18.17.5

INTEGER

read-write

Forces the stratum card to use one of the two specified lines as its clock source when the stratumSyncSource is lineTiming.

INT stratumLineTimingStatus

1.3.6.1.4.1.1751.2.18.17.6

INTEGER

read-only

Represents the source of the current clock.

INT stratumMode

1.3.6.1.4.1.1751.2.18.17.7

INTEGER

read-only

Current status of the primary stratum card. synchronized3(1) stratum is synchronized with accuracy 4.6 x 10e-6 synchronized4(2) stratum is synchronized with accuracy 3.2 x 10e-5 holdover(3) an operating condition of a clock that has lost its controlling input and is using stored data acquired while in normal operation, to control its output freerun(4) an operating condition of the clock whose output signals are internally controlled cardRemoved(5) stratum removed

INT stratumBackupMode

1.3.6.1.4.1.1751.2.18.17.8

INTEGER

read-only

Current status of the backup stratum card.

INT stratumRefFailAction

1.3.6.1.4.1.1751.2.18.17.9

INTEGER

read-write

Defines whether the stratum should switch to freerun or holdover on reference clock failure.

INT stratumPortStatus

1.3.6.1.4.1.1751.2.18.17.10

INTEGER

read-only

Current status of the primary stratum card. portFOS indicates port frequency offset.

INT stratumBkupPortStatus

1.3.6.1.4.1.1751.2.18.17.11

INTEGER

read-only

Current status of the backup stratum card. portFOS indicates port frequency offset.

INT activeStratum

1.3.6.1.4.1.1751.2.18.17.12

INTEGER

read-only

Current status of the backup stratum card.

cellTest

1.3.6.1.4.1.1751.2.18.18

NUM cellTestIfB

1.3.6.1.4.1.1751.2.18.18.1

IntfIndex

read-write

Interface index used for testing cell transfer. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.

INT cellTestVpiB

1.3.6.1.4.1.1751.2.18.18.2

INTEGER

read-write

VPI value for testing cell transfer to an I/O card. Valid range is a number between 0 and 4095. If the I/O card interface is not ATM, then this will always be zero.

INT cellTestVcidB

1.3.6.1.4.1.1751.2.18.18.3

INTEGER

read-write

Virtual Check Id for testing cell transfer to an I/O card. Valid range is a number between 0 and 65535. If the I/O card interface is frame relay, this field acts as DLCI and the valid range is a number between 0 and 1023. If the I/O card interface is circuit emulation, then this will always be 0.

INT cellTestServiceType

1.3.6.1.4.1.1751.2.18.18.4

INTEGER

read-write

Service types for testing cell transfer

INT cellTestConnType

1.3.6.1.4.1.1751.2.18.18.5

INTEGER

read-write

Connection types for testing cell transfer

INT cellTestProtocol

1.3.6.1.4.1.1751.2.18.18.6

INTEGER

read-only

Protocol (interface type) on the I/O

OCT cellTestPayLoadTx

1.3.6.1.4.1.1751.2.18.18.7

OCTET STRING

read-write

PayLoad to be transmitted on I/O interface

OCT cellTestPayLoadRx

1.3.6.1.4.1.1751.2.18.18.8

OCTET STRING

read-only

Last PayLoad received on I/O interface

INT cellTestAction

1.3.6.1.4.1.1751.2.18.18.9

INTEGER

read-write

PayLoad received on I/O interface

I32 cellTestRxPduCount

1.3.6.1.4.1.1751.2.18.18.10

Integer32

read-only

Valid cells received (Input Billing Count)

I32 cellTestTxPduCount

1.3.6.1.4.1.1751.2.18.18.11

Integer32

read-only

Valid cells transmitted (Output Billing Count)

I32 cellTestMismatchPduCount

1.3.6.1.4.1.1751.2.18.18.12

Integer32

read-only

Number of times Rx payload mismatched with Tx payload.

INT cellTestStatus

1.3.6.1.4.1.1751.2.18.18.13

INTEGER

read-only

Indicates whether a cellTest test is in progress or not.

INT cellTestVUNIB

1.3.6.1.4.1.1751.2.18.18.14

INTEGER

read-write

VUNI id for testing cell transfer to an I/O card. This field is valid only for ATM interface.

sysInfo

1.3.6.1.4.1.1751.2.18.19

I32 sysInfoTxOneCellTotal

1.3.6.1.4.1.1751.2.18.19.1

Integer32

read-only

Total amount of cells within the transmit one cell pool.

I32 sysInfoTxOneCellUsed

1.3.6.1.4.1.1751.2.18.19.2

Integer32

read-only

Amount of cells currently being used within the transmit one cell pool.

I32 sysInfoTxOneCellHigh

1.3.6.1.4.1.1751.2.18.19.3

Integer32

read-only

High-water mark of cells used within the transmit one cell pool.

I32 sysInfoRxOneCellTotal

1.3.6.1.4.1.1751.2.18.19.4

Integer32

read-only

Total amount of cells within the receive one cell pool.

I32 sysInfoRxOneCellUsed

1.3.6.1.4.1.1751.2.18.19.5

Integer32

read-only

Amount of cells currently being used within the receive one cell pool.

I32 sysInfoRxOneCellHigh

1.3.6.1.4.1.1751.2.18.19.6

Integer32

read-only

High-water mark of cells used within the receive one cell pool.

I32 sysInfoRxMultiCellTotal

1.3.6.1.4.1.1751.2.18.19.7

Integer32

read-only

Total amount of multi-cells within the receive multi-cell pool.

I32 sysInfoRxMultiCellUsed

1.3.6.1.4.1.1751.2.18.19.8

Integer32

read-only

Amount of multi-cells currently being used within the receive multi-cell pool.

I32 sysInfoRxMultiCellHigh

1.3.6.1.4.1.1751.2.18.19.9

Integer32

read-only

High-water mark of multi-cells used within the receive multi-cell pool.

I32 sysInfoMsgPoolTotal

1.3.6.1.4.1.1751.2.18.19.10

Integer32

read-only

Total amount of messages within the message pool.

I32 sysInfoMsgPoolUsed

1.3.6.1.4.1.1751.2.18.19.11

Integer32

read-only

Amount of messages currently being used within the message pool.

I32 sysInfoMsgPoolHigh

1.3.6.1.4.1.1751.2.18.19.12

Integer32

read-only

High-water mark of messages used within the message pool.

I32 sysInfoDiscFreeKBytes

1.3.6.1.4.1.1751.2.18.19.13

Integer32

read-only

Amount of disc free space available in KB's.

INT sysInfoCpuUtilization1

1.3.6.1.4.1.1751.2.18.19.14

INTEGER

read-only

xx.yy% - cpuUtilization1 is the xx part of it.

INT sysInfoCpuUtilization2

1.3.6.1.4.1.1751.2.18.19.15

INTEGER

read-only

xx.yy% - cpuUtilization2 is the yy part of it.

I32 sysInfoSysUptime

1.3.6.1.4.1.1751.2.18.19.16

Integer32

read-only

Amount of time cpu has been up in seconds.

I32 sysInfoBadCellRx

1.3.6.1.4.1.1751.2.18.19.17

Integer32

read-only

The number of bad cells (BIP16) received so far.

I32 sysInfoMisaligned

1.3.6.1.4.1.1751.2.18.19.18

Integer32

read-only

The number of misaligned cells received so far.

INT sysInfoClockAErr

1.3.6.1.4.1.1751.2.18.19.19

INTEGER

read-only

Value is 1, TRUE, if the clock on backplane A is errored, otherwise, the value is 0, FALSE.

INT sysInfoClockBErr

1.3.6.1.4.1.1751.2.18.19.20

INTEGER

read-only

Value is 1, TRUE, if the clock on backplane B is errored, otherwise, the value is 0, FALSE.

INT sysInfoBIPAErr

1.3.6.1.4.1.1751.2.18.19.21

INTEGER

read-only

Value is 1, TRUE, if the cell circuit on backplane A is errored, otherwise, the value is 0, FALSE.

INT sysInfoBIPBErr

1.3.6.1.4.1.1751.2.18.19.22

INTEGER

read-only

Value is 1, TRUE, if the cell circuit on backplane B is errored, otherwise, the value is 0, FALSE.

I32 sysInfoDiscTotalKBytes

1.3.6.1.4.1.1751.2.18.19.23

Integer32

read-only

Amount of disc space available in KB's.

I32 sysInfoRAMFreeKBytes

1.3.6.1.4.1.1751.2.18.19.24

Integer32

read-only

Amount of RAM memory available for use in KB's.

I32 sysInfoRAMTotalKBytes

1.3.6.1.4.1.1751.2.18.19.25

Integer32

read-only

Amount of RAM memory available on cpu card in KB's.

msgPoolViewTable

1.3.6.1.4.1.1751.2.18.19.26

not-accessible

Table of Msg Pools In the System, Used only for diagnostic purposes

msgPoolViewEntry

1.3.6.1.4.1.1751.2.18.19.26.1

not-accessible

Row definition of Msg Pool Table

I32 msgPoolViewIndex

1.3.6.1.4.1.1751.2.18.19.26.1.1

Integer32

not-accessible

It is the index of the MsgPool array for which the information is requested. Information about Msgs Which are not there in the free pool is returned.A msg is said to be out of the free pool by comparing the signature. The limit being the max number of msgs allowed on the system

I32 msgPoolViewTskId

1.3.6.1.4.1.1751.2.18.19.26.1.2

Integer32

read-only

Task Id of the Sender of the Particular Msg, This will give the integer value, has to be converted to hex for comparison

STR msgPoolViewTskName

1.3.6.1.4.1.1751.2.18.19.26.1.3

DisplayString

read-only

Task Name of the Sender of the Particular Msg

I32 msgPoolViewMsgCmd

1.3.6.1.4.1.1751.2.18.19.26.1.4

Integer32

read-only

msgCmd being sent by the sending Task

INT primaryCpuHwType

1.3.6.1.4.1.1751.2.18.19.27

INTEGER

read-only

Indicates the hardware version type of the primary CPU. version1: 150MHz Saturn13 board supporting 8MB-64MB Memory. version2: 200MHz Saturn15 board supporting 64MB-256MB Memory.

INT secondaryCpuHwType

1.3.6.1.4.1.1751.2.18.19.28

INTEGER

read-only

Indicates the hardware version type of the secondary CPU. version1: 150MHz Saturn13 board supporting 8MB-64MB Memory. version2: 200MHz Saturn15 board supporting 64MB-256MB Memory.

INT sysInfoDiskCheck

1.3.6.1.4.1.1751.2.18.19.29

INTEGER

read-only

Indicates the checking status of the disk in CPU card.

INT switchAlarmStatus

1.3.6.1.4.1.1751.2.18.19.30

INTEGER

read-only

Current status of the alarm on the switch. notAvailable - The alarm status could not be retreived. none - No alarm is present. minor, major, critical - An alarm of the enumerated type is present

ethernetConfig

1.3.6.1.4.1.1751.2.18.20

arp1Table

1.3.6.1.4.1.1751.2.18.20.1

not-accessible

Table of ARP cache data.

arp1Entry

1.3.6.1.4.1.1751.2.18.20.1.1

not-accessible

Row definition for ARP cache.

INT arp1CardSlot

1.3.6.1.4.1.1751.2.18.20.1.1.1

INTEGER

not-accessible

Slot ethernet card is in.

INT arp1BridgeGroupNum

1.3.6.1.4.1.1751.2.18.20.1.1.2

INTEGER

not-accessible

Bridge Group the entry belongs to.

IP arp1IpAddress

1.3.6.1.4.1.1751.2.18.20.1.1.3

IpAddress

not-accessible

Entry IP address.

OCT arp1PhysicalAddr

1.3.6.1.4.1.1751.2.18.20.1.1.4

OCTET STRING

read-only

Entry physical address.

I32 arp1EntryAge

1.3.6.1.4.1.1751.2.18.20.1.1.5

Integer32

read-only

Age of cache entry.

arp2Table

1.3.6.1.4.1.1751.2.18.20.2

not-accessible

Table of ARP cache data.

arp2Entry

1.3.6.1.4.1.1751.2.18.20.2.1

not-accessible

Row definition for ARP cache.

INT arp2CardSlot

1.3.6.1.4.1.1751.2.18.20.2.1.1

INTEGER

not-accessible

Slot ethernet card is in.

INT arp2BridgeGroupNum

1.3.6.1.4.1.1751.2.18.20.2.1.2

INTEGER

not-accessible

Bridge Group the entry belongs to.

OCT arp2PhysicalAddr

1.3.6.1.4.1.1751.2.18.20.2.1.3

OCTET STRING

not-accessible

Entry physical address.

IP arp2IpAddress

1.3.6.1.4.1.1751.2.18.20.2.1.4

IpAddress

read-only

Entry IP address.

I32 arp2EntryAge

1.3.6.1.4.1.1751.2.18.20.2.1.5

Integer32

read-only

Age of cache entry.

bridgeCacheTable

1.3.6.1.4.1.1751.2.18.20.3

not-accessible

Table of bridge cache data.

bridgeCacheEntry

1.3.6.1.4.1.1751.2.18.20.3.1

not-accessible

Row definition for bridge cache.

INT bridgeCacheCardSlot

1.3.6.1.4.1.1751.2.18.20.3.1.1

INTEGER

not-accessible

Slot ethernet card is in.

INT bridgeCacheBridgeGroupNum

1.3.6.1.4.1.1751.2.18.20.3.1.2

INTEGER

not-accessible

Bridge Group the entry belongs to.

OCT bridgeCachePhysicalAddr

1.3.6.1.4.1.1751.2.18.20.3.1.3

OCTET STRING

not-accessible

Entry physical address.

INT bridgeCacheType

1.3.6.1.4.1.1751.2.18.20.3.1.4

INTEGER

read-only

Type of Entry.

INT bridgeCacheSourcePort

1.3.6.1.4.1.1751.2.18.20.3.1.5

INTEGER

read-only

Port entry was obtained from.

I32 bridgeCacheEntryAge

1.3.6.1.4.1.1751.2.18.20.3.1.6

Integer32

read-only

Age of cache entry.

alarmConfig

1.3.6.1.4.1.1751.2.18.21

OCT alarmStatusInputBitmap

1.3.6.1.4.1.1751.2.18.21.1

OCTET STRING

read-only

Remote status from external device. bit = 0 closed, bit = 1 open, LSB 15 bits represent 15 external inputs. MSB bit 15 is always 0.

OCT alarmStatusOutputBitmap

1.3.6.1.4.1.1751.2.18.21.2

OCTET STRING

read-write

Control output for alarm card. bit = 0 deactivated, bit = 1 activated, LSB 4 bits represent 4 external outputs. Bit 0 through bit 3 is output 1 through 4 Control output 4 will be activated upon power failure.

OCT alarmSeverityLevelBitmap

1.3.6.1.4.1.1751.2.18.21.3

OCTET STRING

read-write

Alarm severity level. bit = 0 noAlarm, bit = 1 Alarm present, LSB 3 bits represent severity levels. bit 0 = Minor Alarm, bit 1 = Major Alarm, bit 2 = Critical Alarm.

OCT alarmAcoStatusBitmap

1.3.6.1.4.1.1751.2.18.21.4

OCTET STRING

read-only

Audio alarm status. bit = 0 No alarm cutoff, bit = 1 Alarm cutoff, LSB 3 bits represent audio alarms. bit 0 = Local alarm cutoff, bit 1 = remote alarm cutoff, bit 2 = composite alarm cutoff status.

sysTest

1.3.6.1.4.1.1751.2.18.22

oamTest

1.3.6.1.4.1.1751.2.18.22.1

NUM oamTestIfB

1.3.6.1.4.1.1751.2.18.22.1.1

IntfIndex

read-write

Interface index used for starting loopback test. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.

INT oamTestVpiB

1.3.6.1.4.1.1751.2.18.22.1.2

INTEGER

read-write

VPI value under testing for oam loopback test. Valid range is a number between 0 and 4095.

INT oamTestVciB

1.3.6.1.4.1.1751.2.18.22.1.3

INTEGER

read-write

VCI value under testing for oam loopback test. Valid range is a number between 0 and 65535.

INT oamTestStatus

1.3.6.1.4.1.1751.2.18.22.1.4

INTEGER

read-only

Inidcates the current status of oam test.

INT oamTestAction

1.3.6.1.4.1.1751.2.18.22.1.5

INTEGER

read-write

Test action to be performed.

I32 oamTestTxCount

1.3.6.1.4.1.1751.2.18.22.1.6

Integer32

read-only

Valid cells transmitted.

I32 oamTestRxCount

1.3.6.1.4.1.1751.2.18.22.1.7

Integer32

read-only

Valid cells received.

I32 oamTestMismatchCount

1.3.6.1.4.1.1751.2.18.22.1.8

Integer32

read-only

Number of times Rx correlation tag is mismatched with the Tx correlation tag.

OCT oamTestLocationID

1.3.6.1.4.1.1751.2.18.22.1.9

OCTET STRING

read-write

Location ID of the ATM Node where the loopback is to occur.

INT oamTestLoopbackType

1.3.6.1.4.1.1751.2.18.22.1.10

INTEGER

read-write

OAM Loopback type. Determines whether to send ete or segment loopback cell, and the value of location Id field in the cell. Only for specific-location value, user specified locationId field value taken into account.

oamActDeactTable

1.3.6.1.4.1.1751.2.18.22.2

not-accessible

Table of oam activate and deactivate functions

oamActDeactEntry

1.3.6.1.4.1.1751.2.18.22.2.1

not-accessible

Row definition of oam activate and deactivate

NUM oamActDeactIfB

1.3.6.1.4.1.1751.2.18.22.2.1.1

IntfIndex

not-accessible

Interface index for an OAM CC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.

INT oamActDeactVpiB

1.3.6.1.4.1.1751.2.18.22.2.1.2

INTEGER

not-accessible

VPI value for an oam CC connection. Valid range is a number between 0 and 4095.

INT oamActDeactVciB

1.3.6.1.4.1.1751.2.18.22.2.1.3

INTEGER

not-accessible

VCI value for oam CC connection. Valid range is a number between 0 and 65535.

INT oamActDeactFuncType

1.3.6.1.4.1.1751.2.18.22.2.1.4

INTEGER

read-write

OAM Function type represents the OAM flow for activation or deactivattion for this connection. the possible function types activated in one connection are : fpm-and-br : forward performance monitoring/backward reporting fpm-only : forward performance monitoring continuity-check : continuity check pmbr-and-cc : forward performance monitoring/backward reporting and continuity check pm-and-cc : forward performance monitoring and continuity check

INT oamActDeactDirFlow

1.3.6.1.4.1.1751.2.18.22.2.1.5

INTEGER

read-write

The direction in which cells will be transmitted.

INT oamActDeactFlowType

1.3.6.1.4.1.1751.2.18.22.2.1.6

INTEGER

read-write

Flow Type.

INT oamActDeactBlkSizeAB

1.3.6.1.4.1.1751.2.18.22.2.1.7

INTEGER

read-write

Block Size A-B represents the size of the block of user cells taken into consideration for performance monitoring in A-B direction.

INT oamActDeactBlkSizeBA

1.3.6.1.4.1.1751.2.18.22.2.1.8

INTEGER

read-write

Block Size A-B is the size of the block of user cells taken into consideration for performance monitoring in B-A direction.

INT oamActDeactStsSrcPointEteCC

1.3.6.1.4.1.1751.2.18.22.2.1.9

INTEGER

read-only

Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point

INT oamActDeactStsSnkPointEteCC

1.3.6.1.4.1.1751.2.18.22.2.1.10

INTEGER

read-only

Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point

INT oamActDeactRsltPrevReq

1.3.6.1.4.1.1751.2.18.22.2.1.11

INTEGER

read-only

Cause of Failure shows the reasons of failure of the last activation request on this connection form the local user.

ROW oamActDeactRowStatus

1.3.6.1.4.1.1751.2.18.22.2.1.12

RowStatus

read-write

row status

INT oamActDeactStsSrcPointEtePM

1.3.6.1.4.1.1751.2.18.22.2.1.13

INTEGER

read-only

Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point

INT oamActDeactStsSnkPointEtePM

1.3.6.1.4.1.1751.2.18.22.2.1.14

INTEGER

read-only

Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point

INT oamActDeactStsSrcPointEtePMBR

1.3.6.1.4.1.1751.2.18.22.2.1.15

INTEGER

read-only

Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point

INT oamActDeactStsSnkPointEtePMBR

1.3.6.1.4.1.1751.2.18.22.2.1.16

INTEGER

read-only

Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point

INT oamActDeactBRBlockError

1.3.6.1.4.1.1751.2.18.22.2.1.17

INTEGER

read-only

Backware reporting Block error for PM connection. Valid range is a number between 0 and 32768.

INT oamActDeactBRLostInsertedCell

1.3.6.1.4.1.1751.2.18.22.2.1.18

INTEGER

read-only

Backware reporting lost inserted cell for PM connection. Valid range is a number between 0 and 32768.

INT oamActDeactBRMisInsertedCell

1.3.6.1.4.1.1751.2.18.22.2.1.19

INTEGER

read-only

Backware reporting misinserted cell for PM connection. Valid range is a number between 0 and 32768.

INT oamActDeactStsSrcPointSegPM

1.3.6.1.4.1.1751.2.18.22.2.1.20

INTEGER

read-only

Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point

INT oamActDeactStsSnkPointSegPM

1.3.6.1.4.1.1751.2.18.22.2.1.21

INTEGER

read-only

Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point

INT oamActDeactStsSrcPointSegPMBR

1.3.6.1.4.1.1751.2.18.22.2.1.22

INTEGER

read-only

Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point

INT oamActDeactStsSnkPointSegPMBR

1.3.6.1.4.1.1751.2.18.22.2.1.23

INTEGER

read-only

Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point

INT oamActDeactStsSrcPointSegCC

1.3.6.1.4.1.1751.2.18.22.2.1.24

INTEGER

read-only

Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point

INT oamActDeactStsSnkPointSegCC

1.3.6.1.4.1.1751.2.18.22.2.1.25

INTEGER

read-only

Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point

oamLoopbackTable

1.3.6.1.4.1.1751.2.18.22.3

not-accessible

Table of oam loopback functions

oamLoopbackEntry

1.3.6.1.4.1.1751.2.18.22.3.1

not-accessible

Row definition of oam loop back

NUM oamLpbkIfB

1.3.6.1.4.1.1751.2.18.22.3.1.1

IntfIndex

not-accessible

Interface index used for starting loopback test. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.

INT oamLpbkVpiB

1.3.6.1.4.1.1751.2.18.22.3.1.2

INTEGER

not-accessible

VPI value under testing for oam loopback test. Valid range is a number between 0 and 4095.

INT oamLpbkVciB

1.3.6.1.4.1.1751.2.18.22.3.1.3

INTEGER

not-accessible

VCI value under testing for oam loopback test. Valid range is a number between 0 and 65535.

INT oamLoopbackType

1.3.6.1.4.1.1751.2.18.22.3.1.4

INTEGER

read-write

OAM Loopback type. Determines whether to send ete or segment loopback cell, and the value of location Id field in the cell. Only for specific-location value, user specified locationId field value taken into account.

OCT oamLpbkLocationID

1.3.6.1.4.1.1751.2.18.22.3.1.5

OCTET STRING

read-write

Location ID of the ATM Node where the loopback is to occur.

INT oamLpbkAction

1.3.6.1.4.1.1751.2.18.22.3.1.6

INTEGER

read-write

Test action to be performed. endLoopbackContinuously is not used.

INT oamLpbkStatus

1.3.6.1.4.1.1751.2.18.22.3.1.7

INTEGER

read-only

Inidcates the current status of oam test.

I32 oamLpbkTxCount

1.3.6.1.4.1.1751.2.18.22.3.1.8

Integer32

read-only

Valid cells transmitted.

I32 oamLpbkRxCount

1.3.6.1.4.1.1751.2.18.22.3.1.9

Integer32

read-only

Valid cells received.

I32 oamLpbkMismatchCount

1.3.6.1.4.1.1751.2.18.22.3.1.10

Integer32

read-only

Number of times Rx correlation tag is mismatched with the Tx correlation tag.

I32 oamLpbkTimeout

1.3.6.1.4.1.1751.2.18.22.3.1.11

Integer32

read-only

number of time out

fwDriverSup

1.3.6.1.4.1.1751.2.18.23

cardFwVerTable

1.3.6.1.4.1.1751.2.18.23.1

not-accessible

Table of card firware version status

cardFwVerEntry

1.3.6.1.4.1.1751.2.18.23.1.1

not-accessible

Row definition for card firmware version status

INT cardFwVerSlot

1.3.6.1.4.1.1751.2.18.23.1.1.1

INTEGER

not-accessible

card slot number

I32 cardFwVerType

1.3.6.1.4.1.1751.2.18.23.1.1.2

Integer32

read-write

Card type

OCT cardFwVerCurrent

1.3.6.1.4.1.1751.2.18.23.1.1.3

OCTET STRING

read-only

Card firmware version currently loaded on firmware

I32 cardFwVerCurrentIsDefault

1.3.6.1.4.1.1751.2.18.23.1.1.4

Integer32

read-only

curent driver is default

OCT cardFwVerNext

1.3.6.1.4.1.1751.2.18.23.1.1.5

OCTET STRING

read-write

Card firmware version that user wants to upgrade to. The values are limited those supported by the release.

INT cardFwVerNextIsDefault

1.3.6.1.4.1.1751.2.18.23.1.1.6

INTEGER

read-write

next driver is default

INT cardFwDnldStatus

1.3.6.1.4.1.1751.2.18.23.1.1.7

INTEGER

read-only

firmware download procedure status

I32 cardFwRetries

1.3.6.1.4.1.1751.2.18.23.1.1.8

Integer32

read-only

Number of times firmware download procedure failed consequently.

fwDriverTable

1.3.6.1.4.1.1751.2.18.23.2

not-accessible

Table of available firmware drivers

fwDriverEntry

1.3.6.1.4.1.1751.2.18.23.2.1

not-accessible

Row definition for available firmware drivers

I32 fwSlotId

1.3.6.1.4.1.1751.2.18.23.2.1.1

Integer32

not-accessible

driver slot id

I32 fwDriverType

1.3.6.1.4.1.1751.2.18.23.2.1.2

Integer32

not-accessible

firmware driver type - definition consistent with cardType.

I32 fwIsDefault

1.3.6.1.4.1.1751.2.18.23.2.1.3

Integer32

not-accessible

firmware driver wether default or not

OCT fwDriverName

1.3.6.1.4.1.1751.2.18.23.2.1.4

OCTET STRING

not-accessible

firmware driver file name

I32 fwDriverFrn

1.3.6.1.4.1.1751.2.18.23.2.1.5

Integer32

read-only

Firmware Release Number of firmware driver

I32 fwDriverSize

1.3.6.1.4.1.1751.2.18.23.2.1.6

Integer32

read-only

file size of firmware driver

I32 fwDriverChecksum

1.3.6.1.4.1.1751.2.18.23.2.1.7

Integer32

read-only

checksum of firmware driver file

viprConfig

1.3.6.1.4.1.1751.2.18.24

viprRouterConfigTable

1.3.6.1.4.1.1751.2.18.24.1

not-accessible

Table of Vipr Router Instance Information

viprRouterConfigEntry

1.3.6.1.4.1.1751.2.18.24.1.1

not-accessible

definition for VIPR Route instance attributes

I32 viprSlot

1.3.6.1.4.1.1751.2.18.24.1.1.1

Integer32

not-accessible

The slot number of the Virtual Router card (SS)

INT viprRouterId

1.3.6.1.4.1.1751.2.18.24.1.1.2

INTEGER

not-accessible

A unique Id for the Router Instance in a router card

STR viprRouterName

1.3.6.1.4.1.1751.2.18.24.1.1.3

DisplayString

read-write

The ASCII name of the Router Instance

INT viprRouterNoOfInterfaces

1.3.6.1.4.1.1751.2.18.24.1.1.4

INTEGER

read-only

This variable describes the no of interfaces defined in the Router Instance

INT viprRouterNoOfRoutes

1.3.6.1.4.1.1751.2.18.24.1.1.5

INTEGER

read-only

This variable describes the no of static routes defined in the Router Instance

INT viprRouterAdminStatus

1.3.6.1.4.1.1751.2.18.24.1.1.6

INTEGER

read-write

This variable represents the various X.731 states the Router state machine can take Administartively

INT viprRouterOperStatus

1.3.6.1.4.1.1751.2.18.24.1.1.7

INTEGER

read-only

This variable represents the various X.731 states the Router state machine can take operationally

I32 viprRouterInitTmr

1.3.6.1.4.1.1751.2.18.24.1.1.8

Integer32

read-write

This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.

I32 viprRouterDisabWarnTmr

1.3.6.1.4.1.1751.2.18.24.1.1.9

Integer32

read-write

This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.

I32 viprRouterShutDwnWarnTmr

1.3.6.1.4.1.1751.2.18.24.1.1.10

Integer32

read-write

This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.

INT viprRouterDisableWarning

1.3.6.1.4.1.1751.2.18.24.1.1.11

INTEGER

read-write

This variable when disabled will mask all the warning messages.

INT viprRouterDisableReason

1.3.6.1.4.1.1751.2.18.24.1.1.12

INTEGER

read-only

This variable describes the reason why the Router in the unlocked-Disabled state.

ROW viprRouterRowStatus

1.3.6.1.4.1.1751.2.18.24.1.1.13

RowStatus

read-write

row status

viprIntfConfigTable

1.3.6.1.4.1.1751.2.18.24.2

not-accessible

Table of Vipr Interface Config Information

viprIntfConfigEntry

1.3.6.1.4.1.1751.2.18.24.2.1

not-accessible

definition for VIPR interface attributes

I32 viprIntfId

1.3.6.1.4.1.1751.2.18.24.2.1.1

Integer32

not-accessible

A unique Id for the Interface in a router instance

IP viprIntfIPAddress

1.3.6.1.4.1.1751.2.18.24.2.1.2

IpAddress

read-write

The IP address of the entrprise network to which the interface is attached to

IP viprIntfIPNetMask

1.3.6.1.4.1.1751.2.18.24.2.1.3

IpAddress

read-write

The IP Subnet Mask of the entrprise network to which the interface is attached to

INT viprIntfAdminStatus

1.3.6.1.4.1.1751.2.18.24.2.1.4

INTEGER

read-write

This variable represents the various X.731 states the Interfce statemachine can take Administratively

INT viprIntfOperStatus

1.3.6.1.4.1.1751.2.18.24.2.1.5

INTEGER

read-only

This variable represents the various X.731 states the Interfce statemachine can take operationally

I32 viprIntfInitTmr

1.3.6.1.4.1.1751.2.18.24.2.1.6

Integer32

read-write

This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.

I32 viprIntfDisabWarnTmr

1.3.6.1.4.1.1751.2.18.24.2.1.7

Integer32

read-write

This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.

I32 viprIntfShutDwnWarnTmr

1.3.6.1.4.1.1751.2.18.24.2.1.8

Integer32

read-write

This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.

INT viprIntfDisableWarning

1.3.6.1.4.1.1751.2.18.24.2.1.9

INTEGER

read-write

This variable when disabled will mask all the Disable warning messages.

INT viprIntfDisableReason

1.3.6.1.4.1.1751.2.18.24.2.1.10

INTEGER

read-only

This variable describes the reason why the Interface in the unlocked-Disabled state.

INT viprIntfRipVersion

1.3.6.1.4.1.1751.2.18.24.2.1.11

INTEGER

read-write

This specifies the version of RIP that interface supports.

INT viprIntfRipMode

1.3.6.1.4.1.1751.2.18.24.2.1.12

INTEGER

read-write

This specifies the mode in which RIP protocol runs.

ROW viprIntfRowStatus

1.3.6.1.4.1.1751.2.18.24.2.1.13

RowStatus

read-write

row status

INT viprIntfRipLineType

1.3.6.1.4.1.1751.2.18.24.2.1.14

INTEGER

read-write

This specifies the line type when the RIP version is 2. When the RIP version is 1, the RIP line type will be set to broadcast(1).

STR viprIntfAuthPasswd

1.3.6.1.4.1.1751.2.18.24.2.1.15

DisplayString

read-write

The authentication password for RIP version 2

viprSubChnlConfigTable

1.3.6.1.4.1.1751.2.18.24.3

not-accessible

Table of Vipr Sub Channel Config Information

viprSubChnlConfigEntry

1.3.6.1.4.1.1751.2.18.24.3.1

not-accessible

definition for VIPR sub channel attributes

I32 viprSubChnlId

1.3.6.1.4.1.1751.2.18.24.3.1.1

Integer32

not-accessible

A unique Id for the sub channel in the interface

NUM viprSubChnlIntfIndex

1.3.6.1.4.1.1751.2.18.24.3.1.2

IntfIndex

read-write

The Slot Port Channel to which the IP Packet to be forwarded when the TOS specified in the incoming IP packet is matched to the TosValue, TosMask pair

INT viprSubChnlTrafficType

1.3.6.1.4.1.1751.2.18.24.3.1.3

INTEGER

read-write

The type of interface configured on the SSPPCCC, viprSubChnlIntfIndex

INT viprSubChnlLlcEncapType

1.3.6.1.4.1.1751.2.18.24.3.1.4

INTEGER

read-write

The encapsulation technique used in making IP packet to ATM cell

INT viprSubChnlMacEncapType

1.3.6.1.4.1.1751.2.18.24.3.1.5

INTEGER

read-write

The encapsulation technique used in making IP packet to ATM cell

INT viprSubChnlTosFeature

1.3.6.1.4.1.1751.2.18.24.3.1.6

INTEGER

read-only

Allow the user to set the TOS values or not

INT viprSubChnlTosValue

1.3.6.1.4.1.1751.2.18.24.3.1.7

INTEGER

read-only

The type of service specified in IP packet masked with viprSubChnlTosMask has to be equal to this value in order to have the IP packets getting forwarded in this sub channel

INT viprSubChnlTosMask

1.3.6.1.4.1.1751.2.18.24.3.1.8

INTEGER

read-only

The Type of Service mask

INT viprSubChnlVpiDlci

1.3.6.1.4.1.1751.2.18.24.3.1.9

INTEGER

read-write

The VPI/DLCI value of the connection

INT viprSubChnlVci

1.3.6.1.4.1.1751.2.18.24.3.1.10

INTEGER

read-write

The VCI value of the connection

INT viprSubChnlSarType

1.3.6.1.4.1.1751.2.18.24.3.1.11

INTEGER

read-only

The SAR Type supported for the connection

INT viprSubChnlServiceType

1.3.6.1.4.1.1751.2.18.24.3.1.12

INTEGER

read-write

The Service types that are supported

INT viprSubChnlFwdErrCorrection

1.3.6.1.4.1.1751.2.18.24.3.1.13

INTEGER

read-write

The Forward error correction to be used

INT viprSubChnlInterworkingType

1.3.6.1.4.1.1751.2.18.24.3.1.14

INTEGER

read-write

The Encapsulation type used for Frame relay subchannels

I32 viprSubChnlFrameSize

1.3.6.1.4.1.1751.2.18.24.3.1.15

Integer32

read-write

The value of this object is the size in octets of the largest frame relay information field for this PVC in the ingress direction (out of the frame relay UNI).

I32 viprSubChnlComBurstSize

1.3.6.1.4.1.1751.2.18.24.3.1.16

Integer32

read-write

The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this PVC in the ingress direction (into the frame relay UNI).

I32 viprSubChnlExcessBurstSize

1.3.6.1.4.1.1751.2.18.24.3.1.17

Integer32

read-write

The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this PVC in the ingress direction (into the frame relay UNI).

I32 viprSubChnlCommitedInfoRate

1.3.6.1.4.1.1751.2.18.24.3.1.18

Integer32

read-write

The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this PVC in the ingress direction (into the frame relay UNI).

INT viprSubChnlTimeInterval

1.3.6.1.4.1.1751.2.18.24.3.1.19

INTEGER

read-only

The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.

I32 viprSubChnlAtmPeakCellRate

1.3.6.1.4.1.1751.2.18.24.3.1.20

Integer32

read-write

Peak cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.

I32 viprSubChnlAtmSustainedCellRate

1.3.6.1.4.1.1751.2.18.24.3.1.21

Integer32

read-write

Sustained cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.

I32 viprSubChnlAtmMaxBurstSize

1.3.6.1.4.1.1751.2.18.24.3.1.22

Integer32

read-write

Maximum burst size, in cells, this will reflect the frame relay parameters in atm terms.

I32 viprSubChnlFrPeakCellRate

1.3.6.1.4.1.1751.2.18.24.3.1.23

Integer32

read-only

Peak cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.

I32 viprSubChnlFrSustainedCellRate

1.3.6.1.4.1.1751.2.18.24.3.1.24

Integer32

read-only

Sustained cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.

I32 viprSubChnlFrMaxBurstSize

1.3.6.1.4.1.1751.2.18.24.3.1.25

Integer32

read-only

Maximum burst size, in cells, this will reflect the frame relay parameters in atm terms.

INT viprSubChnlFlowType

1.3.6.1.4.1.1751.2.18.24.3.1.26

INTEGER

read-write

The type of flow

INT viprSubChnlAdminStatus

1.3.6.1.4.1.1751.2.18.24.3.1.27

INTEGER

read-write

This variable represents the various X.731 states the Sub Channel state machine can take Administartively

INT viprSubChnlOperStatus

1.3.6.1.4.1.1751.2.18.24.3.1.28

INTEGER

read-only

This variable represents the various X.731 states the Sub Channel state machine can take Operationally

I32 viprSubChnlInitTmr

1.3.6.1.4.1.1751.2.18.24.3.1.29

Integer32

read-write

This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.

I32 viprSubChnlDisabWarnTmr

1.3.6.1.4.1.1751.2.18.24.3.1.30

Integer32

read-write

This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.

I32 viprSubChnlShutDwnWarnTmr

1.3.6.1.4.1.1751.2.18.24.3.1.31

Integer32

read-write

This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.

INT viprSubChnlDisableWarning

1.3.6.1.4.1.1751.2.18.24.3.1.32

INTEGER

read-write

This variable when disabled will mask all the Disable warning messages.

INT viprSubChnlDisableReason

1.3.6.1.4.1.1751.2.18.24.3.1.33

INTEGER

read-only

This variable describes the reason why the SubChnl in the unlocked-Disabled state.

ROW viprSubChnlRowStatus

1.3.6.1.4.1.1751.2.18.24.3.1.34

RowStatus

read-write

row status

IP viprSubChnlImIpAddr

1.3.6.1.4.1.1751.2.18.24.3.1.35

IpAddress

read-write

inband management IpAddr

IP viprSubChnlImMask

1.3.6.1.4.1.1751.2.18.24.3.1.36

IpAddress

read-write

inband management Mask

INT viprSubChnlViB

1.3.6.1.4.1.1751.2.18.24.3.1.37

INTEGER

read-write

The viB value of the connection

INT viprSubChnlVUNIB

1.3.6.1.4.1.1751.2.18.24.3.1.38

INTEGER

read-write

The VUNIB value of the connection

INT viprSubChnlTrafficShaping

1.3.6.1.4.1.1751.2.18.24.3.1.39

INTEGER

read-write

Traffic Shaping Support in the A2B direction for outgoing ATM connections.

INT viprSubChnlAtmOamStatus

1.3.6.1.4.1.1751.2.18.24.3.1.40

INTEGER

read-write

Indicates the OAM monitoring status. The 3 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI. End-Seg-Pt: Connection endPoint that is also a segment endPoint.

viprRouteConfigTable

1.3.6.1.4.1.1751.2.18.24.4

not-accessible

Table of Vipr static route Config Information

viprRouteConfigEntry

1.3.6.1.4.1.1751.2.18.24.4.1

not-accessible

Definition for Vipr static route attributes

I32 viprRouteId

1.3.6.1.4.1.1751.2.18.24.4.1.1

Integer32

not-accessible

The unique Id to the routing table entry

IP viprRouteIPAddress

1.3.6.1.4.1.1751.2.18.24.4.1.2

IpAddress

read-write

The IP address of the host/network in the route entry

IP viprRouteIPNetMask

1.3.6.1.4.1.1751.2.18.24.4.1.3

IpAddress

read-write

The IP Subnet Mask for the route entry to identify whether the route entry is a host or network

IP viprRouteDestAddress

1.3.6.1.4.1.1751.2.18.24.4.1.4

IpAddress

read-write

The IP address of the host/network in the route entry

IP viprRouteGatewayAddress

1.3.6.1.4.1.1751.2.18.24.4.1.5

IpAddress

read-write

The IP address of the Gateway

INT viprRouteServiceType

1.3.6.1.4.1.1751.2.18.24.4.1.6

INTEGER

read-write

The Service types that are supported

I32 viprRouteMetric

1.3.6.1.4.1.1751.2.18.24.4.1.7

Integer32

read-write

A scalar value for user-supplied static route metric values.

INT viprRouteAdminStatus

1.3.6.1.4.1.1751.2.18.24.4.1.8

INTEGER

read-write

This variable represents the various X.731 states the Route state machine can take Administratively

INT viprRouteOperStatus

1.3.6.1.4.1.1751.2.18.24.4.1.9

INTEGER

read-only

This variable represents the various X.731 states the Route state machine can take Operationally

I32 viprRouteInitTmr

1.3.6.1.4.1.1751.2.18.24.4.1.10

Integer32

read-write

This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.

I32 viprRouteDisabWarnTmr

1.3.6.1.4.1.1751.2.18.24.4.1.11

Integer32

read-write

This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.

I32 viprRouteShutDwnWarnTmr

1.3.6.1.4.1.1751.2.18.24.4.1.12

Integer32

read-write

This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.

INT viprRouteDisableWarning

1.3.6.1.4.1.1751.2.18.24.4.1.13

INTEGER

read-write

This variable when disabled will mask all the Disable warning messages.

INT viprRouteDisableReason

1.3.6.1.4.1.1751.2.18.24.4.1.14

INTEGER

read-only

This variable describes the reason why the Route in the unlocked-Disabled state.

ROW viprRouteRowStatus

1.3.6.1.4.1.1751.2.18.24.4.1.15

RowStatus

read-write

row status

IP viprRouteDestMask

1.3.6.1.4.1.1751.2.18.24.4.1.16

IpAddress

read-write

The IP Mask of the host/network in the route entry

viprRoutingConfigTable

1.3.6.1.4.1.1751.2.18.24.5

not-accessible

Table of Vipr routes Config Information

viprRoutingConfigEntry

1.3.6.1.4.1.1751.2.18.24.5.1

not-accessible

Definition for Vipr route attributes

INT viprRoutingCommand

1.3.6.1.4.1.1751.2.18.24.5.1.1

INTEGER

not-accessible

The Routing table request command Set to start to initiate the caching of first 15 entries Set to more to initiate the caching of next 15 entries Set to abort to reset the counter in I/O card Set to retrieve in order to get the entries

IP viprRoutingIPAddress

1.3.6.1.4.1.1751.2.18.24.5.1.2

IpAddress

read-only

The IP address of the host/network in the route entry

IP viprRoutingIPNetMask

1.3.6.1.4.1.1751.2.18.24.5.1.3

IpAddress

read-only

The IP Subnet Mask for the route entry to identify whether the route entry is a host or network

IP viprRoutingDestAddress

1.3.6.1.4.1.1751.2.18.24.5.1.4

IpAddress

read-only

The IP address of the host/network in the route entry

IP viprRoutingGatewayAddress

1.3.6.1.4.1.1751.2.18.24.5.1.5

IpAddress

read-only

The IP address of the Gateway

INT viprRoutingServiceType

1.3.6.1.4.1.1751.2.18.24.5.1.6

INTEGER

read-only

The Service types that are supported

INT viprRoutingType

1.3.6.1.4.1.1751.2.18.24.5.1.7

INTEGER

read-only

Route types supported by the RS Card.

I32 viprRoutingMetric

1.3.6.1.4.1.1751.2.18.24.5.1.8

Integer32

read-only

The Path cost

IP viprRoutingDestMask

1.3.6.1.4.1.1751.2.18.24.5.1.9

IpAddress

read-only

The IP address Mask of the host/network in the route entry

I32 viprRoutingAge

1.3.6.1.4.1.1751.2.18.24.5.1.10

Integer32

read-only

Age of the routing entry

I32 viprRoutingIndex

1.3.6.1.4.1.1751.2.18.24.5.1.11

Integer32

not-accessible

Index to the routing entry

viprArpConfigTable

1.3.6.1.4.1.1751.2.18.24.6

not-accessible

Table of Vipr Arp Table Information

viprArpConfigEntry

1.3.6.1.4.1.1751.2.18.24.6.1

not-accessible

Definition for Vipr Arp Table attributes

INT viprArpCommand

1.3.6.1.4.1.1751.2.18.24.6.1.1

INTEGER

not-accessible

The ARP table request command Set to start to initiate the caching of first 15 entries Set to more to initiate the caching of next 15 entries Set to abort to reset the counter in I/O card Set to retrieve in order to get the entries

IP viprArpIPAddress

1.3.6.1.4.1.1751.2.18.24.6.1.2

IpAddress

read-only

The IP address of the host/network

OCT viprArpHwAddress

1.3.6.1.4.1.1751.2.18.24.6.1.3

OCTET STRING

read-only

The hardware address of the host/network

I32 viprArpEntryAge

1.3.6.1.4.1.1751.2.18.24.6.1.4

Integer32

read-only

Age of cache entry.

IP viprArpInterfaceIPAddress

1.3.6.1.4.1.1751.2.18.24.6.1.5

IpAddress

read-only

The Interface IP address through which it is learned

IP viprArpInterfaceIPMask

1.3.6.1.4.1.1751.2.18.24.6.1.6

IpAddress

read-only

The Interface IP address Mask

INT viprArpInterfaceServiceType

1.3.6.1.4.1.1751.2.18.24.6.1.7

INTEGER

read-only

The Service type of the interface through which the ARP table is learned

I32 viprArpIndex

1.3.6.1.4.1.1751.2.18.24.6.1.8

Integer32

not-accessible

The Index to the Arp table

viprPingConfigTable

1.3.6.1.4.1.1751.2.18.24.7

not-accessible

Table of Vipr Ping Table Information

viprPingConfigEntry

1.3.6.1.4.1.1751.2.18.24.7.1

not-accessible

Definition for Vipr Ping Table attributes

IP ipAddr

1.3.6.1.4.1.1751.2.18.24.7.1.1

IpAddress

not-accessible

The IP address of the host/network to be echoed

INT pingStatus

1.3.6.1.4.1.1751.2.18.24.7.1.2

INTEGER

read-only

The response value - Alive/Not Alive

viprRipConfigTable

1.3.6.1.4.1.1751.2.18.24.8

not-accessible

Table of Vipr Rip Update Interval for each card

viprRipConfigEntry

1.3.6.1.4.1.1751.2.18.24.8.1

not-accessible

Definition of Rip Update attributes

INT viprRipUpdateInt

1.3.6.1.4.1.1751.2.18.24.8.1.1

INTEGER

read-write

This variable represents the Rip Update Interval used by the RIP protocol to transmit packets. The unit is in seconds. The default is 30 seconds and user can change it to 8 or 16 seconds for a route server card. The value will apply to all VPN's in a route server card. But different route server cards in different slots can have separate values for Rip Update Interval

toneAnnceControl

1.3.6.1.4.1.1751.2.18.25

INT tasCmprsAnnceId

1.3.6.1.4.1.1751.2.18.25.31

INTEGER

read-write

Announcement ID for this announcement file to be compressed.

INT tasCmprsAnnceReplaceId

1.3.6.1.4.1.1751.2.18.25.32

INTEGER

read-write

Announcement ID of the announcement file to be replaced from the announcement table by this file.

STR tasCmprsAnnceFilename

1.3.6.1.4.1.1751.2.18.25.33

DisplayString

read-write

File name for this announcement which is to be compressed.

STR tasCmprsAnnceDescription

1.3.6.1.4.1.1751.2.18.25.34

DisplayString

read-write

Description for this announcement which is to to be compressed.

INT tasCmprsAnnceCmprsType

1.3.6.1.4.1.1751.2.18.25.35

INTEGER

read-write

The type of compression used for storing this announcement.

INT tasCmprsAnnceType

1.3.6.1.4.1.1751.2.18.25.36

INTEGER

read-write

The type of this announcement.

NUM tasCmprsAnnceIntfIndex

1.3.6.1.4.1.1751.2.18.25.37

IntfIndex

read-write

Interface index in SSPPCCC format of TASM card on which this announcement is to be compressed.

INT tasCmprsAction

1.3.6.1.4.1.1751.2.18.25.38

INTEGER

read-write

Action to be performed on this announcement.

INT tasTstAnnceId

1.3.6.1.4.1.1751.2.18.25.39

INTEGER

read-write

Announcement ID to be played for testing.

NUM tasTstAnnceIntfIndex

1.3.6.1.4.1.1751.2.18.25.40

IntfIndex

read-write

Interface index in SSPPCCC format of CE card on which this announcement is to be played for testing.

INT tasTstAnnceLawType

1.3.6.1.4.1.1751.2.18.25.41

INTEGER

read-write

The type of CE card towards which this announcement is to be played. A-Law is for E1 and U-Law is for DS1

INT tasTstAnnceAction

1.3.6.1.4.1.1751.2.18.25.42

INTEGER

read-write

Action to be performed on this announcement for testing.

I32 tasTstLineId

1.3.6.1.4.1.1751.2.18.25.43

Integer32

read-write

Test ID to be started for line testing.

NUM tasTstLineIntfIndex

1.3.6.1.4.1.1751.2.18.25.44

IntfIndex

read-write

Interface index in SSPPCCC format of CE card on which this test is to be initiated.

INT tasTstLineAction

1.3.6.1.4.1.1751.2.18.25.45

INTEGER

read-write

Test action to be performed.

NUM tasMemIntfIndex

1.3.6.1.4.1.1751.2.18.25.46

IntfIndex

read-write

Interface index in SSPPCCC format of TASM card on which the memory is to be initialised.

INT tasMemAction

1.3.6.1.4.1.1751.2.18.25.47

INTEGER

read-write

Test action to be performed.

IP toneAnnceIpAddress

1.3.6.1.4.1.1751.2.18.25.48

IpAddress

read-write

IP Address for announcement ftp server.

STR toneAnnceAccountName

1.3.6.1.4.1.1751.2.18.25.49

DisplayString

read-write

ftp account name for access to announcement ftp server.

STR toneAnnceAccountPassword

1.3.6.1.4.1.1751.2.18.25.50

DisplayString

read-write

ftp account password for access to announcement ftp server.

STR toneAnnceSourceFile

1.3.6.1.4.1.1751.2.18.25.51

DisplayString

read-write

announcement file with complete path on the ftp server

STR toneAnnceDestinationFile

1.3.6.1.4.1.1751.2.18.25.52

DisplayString

read-write

The announcementSourceFile will be renamed with MS DOS file format and placed in the /scsi/announce directory on the disk.

INT toneAnnceFtpStatus

1.3.6.1.4.1.1751.2.18.25.53

INTEGER

read-only

Current status of the ftp announcement download. Status of the software announcement. noActivity is the initial start state from boot-up. working is set while ftp'ing the announcement. The final state is one of doneSuccessfully, doneWithError, or aborted, all self-explanatory. It will stay in this state until re-boot or starting an announcement. If the state is doneWithError then announcementSwErrorStatus will be set to reflect the type of error.

INT toneAnnceFtpErrorStatus

1.3.6.1.4.1.1751.2.18.25.54

INTEGER

read-only

The result of the finish of the ftp software announcement download. Set to a value 3-21 if announcementSwCopyStatus is doneWithError. Set to none if announcementFtpCopyStatus is doneSuccessfully. Set to userAbort if announcementSwCopyStatus is aborted.

INT toneAnnceFtpAction

1.3.6.1.4.1.1751.2.18.25.55

INTEGER

read-write

start ftp announcement files. When announcementFtpCopyStatus is working, the start request will be ignored. Abort will have effect only when announcementFtpCopystatus is working.

gr303Config

1.3.6.1.4.1.1751.2.18.26

gr303IgConfig

1.3.6.1.4.1.1751.2.18.26.1

gr303IgConfigTable

1.3.6.1.4.1.1751.2.18.26.1.1

not-accessible

Table of GR303 group configuration

gr303IgConfigEntry

1.3.6.1.4.1.1751.2.18.26.1.1.1

not-accessible

Row definition for GR303 group configuration

INT gr303IgId

1.3.6.1.4.1.1751.2.18.26.1.1.1.1

INTEGER

not-accessible

This is used as an index into GR303IG table which recognizes GR303 Interface Group

ROW gr303IgRowStatus

1.3.6.1.4.1.1751.2.18.26.1.1.1.2

RowStatus

read-write

GR303IG config entry row status

INT gr303IgAdminStatus

1.3.6.1.4.1.1751.2.18.26.1.1.1.3

INTEGER

read-write

Administrative status of the GR303IG

NUM gr303IgPrimaryTMCChanIntfId

1.3.6.1.4.1.1751.2.18.26.1.1.1.4

IntfIndex

read-write

Primary TMC channel Interface Id in SSPPCCC format

NUM gr303IgPrimaryEOCChanIntfId

1.3.6.1.4.1.1751.2.18.26.1.1.1.5

IntfIndex

read-write

Primary EOC channel Interface Id in SSPPCCC format

NUM gr303IgBackupTMCChanIntfId

1.3.6.1.4.1.1751.2.18.26.1.1.1.6

IntfIndex

read-write

Backup TMC channel Interface Id in SSPPCCC format

NUM gr303IgBackupEOCChanIntfId

1.3.6.1.4.1.1751.2.18.26.1.1.1.7

IntfIndex

read-write

Backup EOC channel Interface Id in SSPPCCC format

INT gr303IgPrimaryTMCStatus

1.3.6.1.4.1.1751.2.18.26.1.1.1.8

INTEGER

read-only

Primary TMC channel Status

INT gr303IgPrimaryEOCStatus

1.3.6.1.4.1.1751.2.18.26.1.1.1.9

INTEGER

read-only

Primary EOC channel Status

INT gr303IgBackupTMCStatus

1.3.6.1.4.1.1751.2.18.26.1.1.1.10

INTEGER

read-only

Backup TMC channel Status.Value null(5) Indicates that the Backup TMC has not been configured.

INT gr303IgBackupEOCStatus

1.3.6.1.4.1.1751.2.18.26.1.1.1.11

INTEGER

read-only

Backup EOC channel Status.Value null(5) Indicates that the Backup EOC has not been configured.

INT gr303IgTMCProtSwitchProvState

1.3.6.1.4.1.1751.2.18.26.1.1.1.12

INTEGER

read-write

Lock/Unlock the protection switch

INT gr303IgEOCProtSwitchProvState

1.3.6.1.4.1.1751.2.18.26.1.1.1.13

INTEGER

read-write

Lock/Unlock the protection switch

INT gr303IgTMCProtSwitchCommand

1.3.6.1.4.1.1751.2.18.26.1.1.1.14

INTEGER

read-write

User command to do path protection switch

INT gr303IgEOCProtSwitchCommand

1.3.6.1.4.1.1751.2.18.26.1.1.1.15

INTEGER

read-write

User command to do path protection switch

INT gr303IgLocalDigitalSwitchType

1.3.6.1.4.1.1751.2.18.26.1.1.1.16

INTEGER

read-write

LDS (IDT) type

INT gr303IgLocalDigitalSwitchVersion

1.3.6.1.4.1.1751.2.18.26.1.1.1.17

INTEGER

read-write

LDS (IDT)Version

gr303IgIntfConfigTable

1.3.6.1.4.1.1751.2.18.26.1.2

not-accessible

Table of interface attributes in an GR303IG

gr303IgIntfConfigEntry

1.3.6.1.4.1.1751.2.18.26.1.2.1

not-accessible

Row definition for GR303 Access Arrangement Interface configuration

INT gr303IntfIgId

1.3.6.1.4.1.1751.2.18.26.1.2.1.1

INTEGER

not-accessible

This is used as an index into GR303Ig table which recognizes GR303 Interface Group. This is used as a first index into this interface table.

INT gr303IgIntfId

1.3.6.1.4.1.1751.2.18.26.1.2.1.2

INTEGER

not-accessible

This is used as an index into IG interface table which recognizes GR303 Ig interfaces. This is used as a second index into this table

I32 gr303IgIntfPhysId

1.3.6.1.4.1.1751.2.18.26.1.2.1.3

Integer32

read-write

Interface's Physical ID (SSPPCCC)

I32 gr303IgIntfNetId

1.3.6.1.4.1.1751.2.18.26.1.2.1.4

Integer32

read-only

gr303Ig Interface (DS1) Net Id assigned by the network

ROW gr303IgIntfRowStatus

1.3.6.1.4.1.1751.2.18.26.1.2.1.5

RowStatus

read-write

GR303IG interface entry row status - row status can not be made active until all the values are set

gr303LapdConfigTable

1.3.6.1.4.1.1751.2.18.26.1.4

not-accessible

Table of LAPD attributes in an GR303IG

gr303LapdConfigEntry

1.3.6.1.4.1.1751.2.18.26.1.4.1

not-accessible

Row definition for LAPD attributes in a GR303IG

INT gr303LapdIgId

1.3.6.1.4.1.1751.2.18.26.1.4.1.1

INTEGER

not-accessible

GR303IG Number index which recognizes GR303 Interface group

INT gr303T200

1.3.6.1.4.1.1751.2.18.26.1.4.1.2

INTEGER

read-write

value of Lapd T200 timer in miliseconds in step size of 50 ms

INT gr303T203

1.3.6.1.4.1.1751.2.18.26.1.4.1.3

INTEGER

read-write

value of Lapd T203 timer in seconds

INT gr303N200

1.3.6.1.4.1.1751.2.18.26.1.4.1.4

INTEGER

read-write

Maximum number of retransmissions

INT gr303K

1.3.6.1.4.1.1751.2.18.26.1.4.1.5

INTEGER

read-write

Maximum number of outstanding I frames - Lapd - window size.

gr303TMCConfigTable

1.3.6.1.4.1.1751.2.18.26.1.5

not-accessible

Table of Layer 3 attributes in an GR303IG

gr303TMCConfigEntry

1.3.6.1.4.1.1751.2.18.26.1.5.1

not-accessible

Row definition for GR303 Access Arrangement Layer3 parameters configuration

INT gr303TMCIgId

1.3.6.1.4.1.1751.2.18.26.1.5.1.1

INTEGER

not-accessible

GR303IG Number index which recognizes GR303 Interface group

INT gr303TMCT303

1.3.6.1.4.1.1751.2.18.26.1.5.1.2

INTEGER

read-write

value of TMC T303 timer in miliseconds with a step size of 500 ms

INT gr303TMCT396

1.3.6.1.4.1.1751.2.18.26.1.5.1.3

INTEGER

read-write

value of TMC T396 timer in miliseconds with a step size of 1000 ms

gr303Stats

1.3.6.1.4.1.1751.2.18.27

gr303IgStats

1.3.6.1.4.1.1751.2.18.27.1

gr303IgStatsTable

1.3.6.1.4.1.1751.2.18.27.1.1

not-accessible

Table of GR303 GR303IG based stats attributes

gr303IgStatsEntry

1.3.6.1.4.1.1751.2.18.27.1.1.1

not-accessible

Row definition for GR303 GR303IG based stats

INT gr303IgStatsIgId

1.3.6.1.4.1.1751.2.18.27.1.1.1.1

INTEGER

not-accessible

This is used as an index into GR303 Ig table which recognizes GR303 Interface Group Interface group

I32 gr303IgStatsCurrentInCalls

1.3.6.1.4.1.1751.2.18.27.1.1.1.2

Integer32

read-only

Total number of Currently established incoming calls

I32 gr303IgStatsCurrentOutCalls

1.3.6.1.4.1.1751.2.18.27.1.1.1.3

Integer32

read-only

Total number of Currently established outgoing calls

I32 gr303IgStatsOutCallSuccessful

1.3.6.1.4.1.1751.2.18.27.1.1.1.4

Integer32

read-only

Total number successful outgoing calls

I32 gr303IgStatsOutCallFailed

1.3.6.1.4.1.1751.2.18.27.1.1.1.5

Integer32

read-only

Total number of Failed outgoing calls

I32 gr303IgStatsInCallSuccessful

1.3.6.1.4.1.1751.2.18.27.1.1.1.6

Integer32

read-only

Total number successful incoming calls

I32 gr303IgStatsInCallFailed

1.3.6.1.4.1.1751.2.18.27.1.1.1.7

Integer32

read-only

Total number of Failed incoming calls

INT gr303IgStatsReset

1.3.6.1.4.1.1751.2.18.27.1.1.1.8

INTEGER

read-write

gr303Ig reset statistics button

atmTrunkingMIBObjects

1.3.6.1.4.1.1751.2.18.28

atmTrunkingIWFBaseGroup

1.3.6.1.4.1.1751.2.18.28.1

I32 atmTrunkingIWFIdentifier

1.3.6.1.4.1.1751.2.18.28.1.1

Integer32

read-write

IWF ID for the local endpoint

OCT atmTrunkingIWFLocalAddress

1.3.6.1.4.1.1751.2.18.28.1.2

OCTET STRING

read-write

IWF ATM address for the local endpoint

I32 atmTrunkingIWFMaxRemoteIWF

1.3.6.1.4.1.1751.2.18.28.1.3

Integer32

read-write

Maximum remote IWF that can connect to this endpoint

INT atmTrunkingIWFAdminStatus

1.3.6.1.4.1.1751.2.18.28.1.4

INTEGER

read-write

Indicates whether the Local IWF is active or not

atmTrunkingRemoteIWFTable

1.3.6.1.4.1.1751.2.18.28.2

not-accessible

Remote IWF table

atmTrunkingRemoteIWFEntry

1.3.6.1.4.1.1751.2.18.28.2.1

not-accessible

Entry in atmTrunkingRemoteIWFTable

I32 atmTrunkingRemoteIWFIdentifier

1.3.6.1.4.1.1751.2.18.28.2.1.1

Integer32

not-accessible

IWF ID for the remote IWF

OCT atmTrunkingRemoteIWFAddress

1.3.6.1.4.1.1751.2.18.28.2.1.2

OCTET STRING

read-create

IWF ATM address for the remote IWF

INT atmTrunkingRemoteIWFTrnkMode

1.3.6.1.4.1.1751.2.18.28.2.1.3

INTEGER

read-create

Maximum remote IWF that can connect to this endpoint

INT atmTrunkingRemoteIWFAdminStatus

1.3.6.1.4.1.1751.2.18.28.2.1.4

INTEGER

read-create

Indicates whether the Local IWF is active or not

ROW atmTrunkingRemoteIWFRowStatus

1.3.6.1.4.1.1751.2.18.28.2.1.5

RowStatus

read-create

Maximum remote IWF that can connect to this endpoint

atmTrunkingSigVccTable

1.3.6.1.4.1.1751.2.18.28.3

not-accessible

Table of iwf signaling vcc configuration entities

atmTrunkingSigVccEntry

1.3.6.1.4.1.1751.2.18.28.3.1

not-accessible

Entry in atmTrunkingSigVccTable

I32 atmTrunkingSigVccRmtIWFIdentifier

1.3.6.1.4.1.1751.2.18.28.3.1.1

Integer32

not-accessible

IWF ID for the remote IWF

INT atmTrunkingSigVccIdentifier

1.3.6.1.4.1.1751.2.18.28.3.1.2

INTEGER

not-accessible

Vcc ID assigned by the owner of this signaling Vcc

NUM atmTrunkingSigVccOutgoingIfIndex

1.3.6.1.4.1.1751.2.18.28.3.1.3

IntfIndex

read-create

Intf index of the outgoing interface,readonly for SVC/SPVC

INT atmTrunkingSigVccOutgoingVpi

1.3.6.1.4.1.1751.2.18.28.3.1.4

INTEGER

read-create

VPI used at the outgoing interface, readonly for SVC/SPVC

INT atmTrunkingSigVccOutgoingVci

1.3.6.1.4.1.1751.2.18.28.3.1.5

INTEGER

read-create

VCI used at the outgoing interface, readonly for SVC/SPVC

INT atmTrunkingSigVccOwner

1.3.6.1.4.1.1751.2.18.28.3.1.6

INTEGER

read-create

Indicates who is the owner of the Sig VCC

I32 atmTrunkingSigVccInactiveTimer

1.3.6.1.4.1.1751.2.18.28.3.1.7

Integer32

read-create

Inactive time period on which to clear the call

INT atmTrunkingSigVccType

1.3.6.1.4.1.1751.2.18.28.3.1.8

INTEGER

read-create

Indicates if the SigVcc should be setup as PVC/SPVC/SVC

INT atmTrunkingSigVccSignaling

1.3.6.1.4.1.1751.2.18.28.3.1.9

INTEGER

read-create

Indicates the signalling protocol used between the IWFs

I32 atmTrunkingSigVccFwPcr01

1.3.6.1.4.1.1751.2.18.28.3.1.10

Integer32

read-create

Forward PCR for the call

I32 atmTrunkingSigVccBwPcr01

1.3.6.1.4.1.1751.2.18.28.3.1.11

Integer32

read-create

Backward PCR for the call

I32 atmTrunkingSigVccFwScr01

1.3.6.1.4.1.1751.2.18.28.3.1.12

Integer32

read-create

Forward SCR for the call

I32 atmTrunkingSigVccBwScr01

1.3.6.1.4.1.1751.2.18.28.3.1.13

Integer32

read-create

Backward SCR for the call

I32 atmTrunkingSigVccFwMbs01

1.3.6.1.4.1.1751.2.18.28.3.1.14

Integer32

read-create

Forward MBS for the call

I32 atmTrunkingSigVccBwMbs01

1.3.6.1.4.1.1751.2.18.28.3.1.15

Integer32

read-create

Backward MBS for the call

I32 atmTrunkingSigVccMaxAal2Vcc

1.3.6.1.4.1.1751.2.18.28.3.1.16

Integer32

read-create

Maximum number of bearer VCCs controlled by this SigVcc

I32 atmTrunkingSigVccActiveAal2Vcc

1.3.6.1.4.1.1751.2.18.28.3.1.17

Integer32

read-only

Number of active bearer VCCs controlled by this SigVcc

INT atmTrunkingSigVccOperStatus

1.3.6.1.4.1.1751.2.18.28.3.1.18

INTEGER

read-only

Indicates whether the Local IWF is active or not

ROW atmTrunkingSigVccRowStatus

1.3.6.1.4.1.1751.2.18.28.3.1.19

RowStatus

read-create

Row status

INT atmTrunkingSigVccViB

1.3.6.1.4.1.1751.2.18.28.3.1.20

INTEGER

read-create

VI to associate the Egress part of A2B connection

INT atmTrunkingSigVccVUNIB

1.3.6.1.4.1.1751.2.18.28.3.1.21

INTEGER

read-create

VUNI associated the Egress part of A2B connection

I32 atmTrunkingSigVccRetryTimer

1.3.6.1.4.1.1751.2.18.28.3.1.22

Integer32

read-create

the time(seconds) to wait before attempting to establish the ATM Trunking Signalling VCC SPVC after previous failed call attempt. 0 indicates retries will be attempted immedi ately

I32 atmTrunkingSigVccRetryLimit

1.3.6.1.4.1.1751.2.18.28.3.1.23

Integer32

read-create

ATM Trunking Signalling VCC SPVC Retry Limit. 0 indicates unlimited

INT atmTrunkingSigVccRestart

1.3.6.1.4.1.1751.2.18.28.3.1.24

INTEGER

read-write

The active ATM Trunking SPVC is released, if necessary, and a new setup procedure is begun if restart, otherwise, noop.

INT atmTrunkingSigVccPriority

1.3.6.1.4.1.1751.2.18.28.3.1.25

INTEGER

read-write

Priority of TrunkingSigVcc - priority-1 being highest priority .

I32 atmTrunkingSigVccRetryCounter

1.3.6.1.4.1.1751.2.18.28.3.1.26

Integer32

read-only

Indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the SigVcc SPVC is restarted.

atmTrunkingBrVccConfigTable

1.3.6.1.4.1.1751.2.18.28.4

not-accessible

Table of iwf aal2 bearer vcci configuration entities

atmTrunkingBrVccConfigEntry

1.3.6.1.4.1.1751.2.18.28.4.1

not-accessible

Row definition for iwf aal2 vcci configuration

I32 atmTrunkingBrVccRmtIWFId

1.3.6.1.4.1.1751.2.18.28.4.1.1

Integer32

not-accessible

IWF ID for the remote IWF

INT atmTrunkingBrVccSigVccId

1.3.6.1.4.1.1751.2.18.28.4.1.2

INTEGER

read-only

Signalling Vcc associated with this Br Vcc

INT atmTrunkingBrVccId

1.3.6.1.4.1.1751.2.18.28.4.1.3

INTEGER

not-accessible

Id of the AAL2 Bear Vcc

NUM atmTrunkingBrVccIf

1.3.6.1.4.1.1751.2.18.28.4.1.4

IntfIndex

read-create

Intf index of the outgoing interface, readonly for SVC/SPVC

INT atmTrunkingBrVccVpi

1.3.6.1.4.1.1751.2.18.28.4.1.5

INTEGER

read-create

VPI value of this VCC connection. Valid range is a number between 0 and 4095.

INT atmTrunkingBrVccVci

1.3.6.1.4.1.1751.2.18.28.4.1.6

INTEGER

read-create

VCI value of this VCC connection. Valid range is a number between 0 and 65535.

INT atmTrunkingBrVccViB

1.3.6.1.4.1.1751.2.18.28.4.1.7

INTEGER

read-create

VI to associate the Egress part of A2B connection

INT atmTrunkingBrVccVUNIB

1.3.6.1.4.1.1751.2.18.28.4.1.8

INTEGER

read-create

VUNI associated the Egress part of A2B connection

INT atmTrunkingBrVccServiceType

1.3.6.1.4.1.1751.2.18.28.4.1.9

INTEGER

read-create

service type

INT atmTrunkingBrVccSarType

1.3.6.1.4.1.1751.2.18.28.4.1.10

INTEGER

read-create

sar type

INT atmTrunkingBrVccOwner

1.3.6.1.4.1.1751.2.18.28.4.1.11

INTEGER

read-create

The owner of this Vcc

INT atmTrunkingBrVccOperStatus

1.3.6.1.4.1.1751.2.18.28.4.1.12

INTEGER

read-only

The Operational Status of this Bearer Vcc

I32 atmTrunkingBrVccFwAtmPcr01

1.3.6.1.4.1.1751.2.18.28.4.1.13

Integer32

read-create

Forward pcr (0+1)

I32 atmTrunkingBrVccBwAtmPcr01

1.3.6.1.4.1.1751.2.18.28.4.1.14

Integer32

read-create

Backward pcr (0+1)

I32 atmTrunkingBrVccFwAtmScr01

1.3.6.1.4.1.1751.2.18.28.4.1.15

Integer32

read-create

Forward scr (0+1)

I32 atmTrunkingBrVccBwAtmScr01

1.3.6.1.4.1.1751.2.18.28.4.1.16

Integer32

read-create

Backward scr (0+1)

I32 atmTrunkingBrVccFwAtmMbs01

1.3.6.1.4.1.1751.2.18.28.4.1.17

Integer32

read-create

Forward Mbs (0+1)

I32 atmTrunkingBrVccBwAtmMbs01

1.3.6.1.4.1.1751.2.18.28.4.1.18

Integer32

read-create

Backward Mbs (0+1)

INT atmTrunkingBrVccConnType

1.3.6.1.4.1.1751.2.18.28.4.1.19

INTEGER

read-create

connection type

I32 atmTrunkingBrVccActiveChanCnt

1.3.6.1.4.1.1751.2.18.28.4.1.20

Integer32

read-only

Number of currently active channels in this Vcc

INT atmTrunkingBrVccMaxAal2ChanId

1.3.6.1.4.1.1751.2.18.28.4.1.21

INTEGER

read-create

Max Id of channels supported within this br vcc

INT atmTrunkingBrVccCircuitModeDataSupp

1.3.6.1.4.1.1751.2.18.28.4.1.22

INTEGER

read-create

Circuit mode data

INT atmTrunkingBrVccFrameModeSupp

1.3.6.1.4.1.1751.2.18.28.4.1.23

INTEGER

read-create

Frame mode data

INT atmTrunkingBrVccFaxModSupp

1.3.6.1.4.1.1751.2.18.28.4.1.24

INTEGER

read-create

FAX Demodulation

INT atmTrunkingBrVccCASPktXportSupp

1.3.6.1.4.1.1751.2.18.28.4.1.25

INTEGER

read-create

Channel Associated Signaling

INT atmTrunkingBrVccDTMFPktXportSupp

1.3.6.1.4.1.1751.2.18.28.4.1.26

INTEGER

read-create

DTMF Dialed Digits

INT atmTrunkingBrVccMFR1PktXportSupp

1.3.6.1.4.1.1751.2.18.28.4.1.27

INTEGER

read-create

MF-R1 Dialed Digits

INT atmTrunkingBrVccMFR2PktXportSupp

1.3.6.1.4.1.1751.2.18.28.4.1.28

INTEGER

read-create

MF-R2 Dialed Digits

INT atmTrunkingBrVccPCMEncoding

1.3.6.1.4.1.1751.2.18.28.4.1.29

INTEGER

read-create

DTMF Dialed Digits

INT atmTrunkingBrVccMaxFrameLength

1.3.6.1.4.1.1751.2.18.28.4.1.30

INTEGER

read-create

Maximum length of frame mode data

INT atmTrunkingBrVccIdleChannSuprSupp

1.3.6.1.4.1.1751.2.18.28.4.1.31

INTEGER

read-create

Idle Channel Supression

INT atmTrunkingBrVccSilenceDetSupp

1.3.6.1.4.1.1751.2.18.28.4.1.32

INTEGER

read-create

Silence Detection

INT atmTrunkingBrVccCompressionSpec

1.3.6.1.4.1.1751.2.18.28.4.1.33

INTEGER

read-create

Compression Type

INT atmTrunkingBrVccAudioProfileSource

1.3.6.1.4.1.1751.2.18.28.4.1.34

INTEGER

read-create

Profile Source

INT atmTrunkingBrVccAudioProfileId

1.3.6.1.4.1.1751.2.18.28.4.1.35

INTEGER

read-create

Profile ID

I32 atmTrunkingBrVccAvailBw

1.3.6.1.4.1.1751.2.18.28.4.1.36

Integer32

read-only

Available Bandwidth left in this Vcc

ROW atmTrunkingBrVccRowStatus

1.3.6.1.4.1.1751.2.18.28.4.1.37

RowStatus

read-create

Row status

INT atmTrunkingBrVccGr303Supp

1.3.6.1.4.1.1751.2.18.28.4.1.38

INTEGER

read-create

GR303 Support

INT atmTrunkingBrVccOamStatus

1.3.6.1.4.1.1751.2.18.28.4.1.39

INTEGER

read-write

Indicates the OAM monitoring status of side A. The 2 possible states are: Unsupp: No monitoring enabled. End-Pt: Atm side is only an end point, therefore it will respond to AIS/RDI.

I32 atmTrunkingBrVccInactiveTimer

1.3.6.1.4.1.1751.2.18.28.4.1.40

Integer32

read-create

The time(in seconds) to wait before releasing the ATM Trunking Bearer VCC SVC after all narrow band calls are dropped

I32 atmTrunkingBrVccRetryTimer

1.3.6.1.4.1.1751.2.18.28.4.1.41

Integer32

read-create

the time(seconds) to wait before attempting to establish the ATM Trunking Bearer VCC SPVC after previous failed call attempt. 0 indicates retries will be attempted immediately

I32 atmTrunkingBrVccRetryLimit

1.3.6.1.4.1.1751.2.18.28.4.1.42

Integer32

read-create

ATM Trunking Bearer VCC SPVC Retry Limit. 0 indicates unlimited

INT atmTrunkingBrVccRestart

1.3.6.1.4.1.1751.2.18.28.4.1.43

INTEGER

read-write

The active ATM Trunking BrVcc SPVC is released, if necessary, and a new setup procedure is begun if 'restart', otherwise, noop.

INT atmTrunkingBrVccCuTimer

1.3.6.1.4.1.1751.2.18.28.4.1.44

INTEGER

read-write

CuTimer represents combined use timer, is set to zero such that every ATM cell transmitted contains one, and only one, AAL2 packet, and the first octet of the AAL2 packet header follows immediately after the Start Field in the ATM cell payload. If the AAL2 packet payload is less than 44 octets, the remainder of the ATM cell payload following the end of the AAL2 packet shall be filled with zeros as padding. Each increment of CuTimer means 5ms more to wait. And cuTimer default value 4 means to wait 20ms before the ATM cell is sent out.

INT atmTrunkingBrVccPriority

1.3.6.1.4.1.1751.2.18.28.4.1.45

INTEGER

read-write

Priority of TrunkingBrVcc - priority-1 being highest priority .

I32 atmTrunkingBrVccRetryCounter

1.3.6.1.4.1.1751.2.18.28.4.1.46

Integer32

read-only

Indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the BrVcc SPVC is restarted.

atmTrunkingDataChannelConfigTable

1.3.6.1.4.1.1751.2.18.28.5

not-accessible

Table of iwf aal2 data channel configuration entities

atmTrunkingDataChannelConfigEntry

1.3.6.1.4.1.1751.2.18.28.5.1

not-accessible

Row definition for iwf aal2 data channel configuration

I32 atmTrunkingDataChannelRmtIWFId

1.3.6.1.4.1.1751.2.18.28.5.1.1

Integer32

not-accessible

IWF ID for the remote IWF

INT atmTrunkingDataChannelSigVccId

1.3.6.1.4.1.1751.2.18.28.5.1.2

INTEGER

read-only

Vcc ID assigned by the owner of this signaling Vcc

INT atmTrunkingDataChannelBrVccId

1.3.6.1.4.1.1751.2.18.28.5.1.3

INTEGER

not-accessible

Id of the AAL2 Bear Vcc

INT atmTrunkingDataChannelId

1.3.6.1.4.1.1751.2.18.28.5.1.4

INTEGER

not-accessible

The AAL2 Channel Id of this channel

INT atmTrunkingDataChanOperStatus

1.3.6.1.4.1.1751.2.18.28.5.1.5

INTEGER

read-only

Operational Status of this channel

INT atmTrunkingDataChanOwner

1.3.6.1.4.1.1751.2.18.28.5.1.6

INTEGER

read-only

The owner of this channel

NUM atmTrunkingDataChanNBIntf

1.3.6.1.4.1.1751.2.18.28.5.1.7

IntfIndex

read-only

The index of narrowband interface this channel is mapped to

protectionGroup

1.3.6.1.4.1.1751.2.18.29

protectionGroupTable

1.3.6.1.4.1.1751.2.18.29.1

not-accessible

Table of interface protection group attributes

protectionGroupEntry

1.3.6.1.4.1.1751.2.18.29.1.1

not-accessible

Defines one interface protection group

I32 pgtGroupId

1.3.6.1.4.1.1751.2.18.29.1.1.1

Integer32

not-accessible

a user selected logical number representing a protection group uniquely within a PSAX

INT pgtSwitchoverMethod

1.3.6.1.4.1.1751.2.18.29.1.1.2

INTEGER

read-write

switchover method to switch traffic from failed primary interface to available standby interface. In auto method, PSAX automatically switches the traffic without user intervention. In manual method, a failed primary does not switch traffic and gives control to user to do so.

INT pgtSwitchbackMethod

1.3.6.1.4.1.1751.2.18.29.1.1.3

INTEGER

read-write

switchback method to switch traffic from a standby to its corresponding recovered primary interface. In auto method, PSAX automatically switches the traffic without user intervention. In manual method, standby does not switch traffic and gives control to user to do so.

INT pgtStandbySelection

1.3.6.1.4.1.1751.2.18.29.1.1.4

INTEGER

read-write

Standby selection method determines the order of selection of standby when primary interface fails. The options are: sequential -- internally select next higher available standby to the last one, latest_used -- used last one freed, oldest_used -- used to longest idle one, random \255 randomly select one, explicit -- selected by user.

ROW pgtRowStatus

1.3.6.1.4.1.1751.2.18.29.1.1.5

RowStatus

read-write

row status

interfaceProtectionTable

1.3.6.1.4.1.1751.2.18.29.2

not-accessible

Table of interface protection attributes

interfaceProtectionEntry

1.3.6.1.4.1.1751.2.18.29.2.1

not-accessible

Defines attributes for interface protection

I32 iptGroupId

1.3.6.1.4.1.1751.2.18.29.2.1.1

Integer32

not-accessible

a user selected logical number representing a protection group uniquely within a PSAX.

I32 iptLogicalIntfId

1.3.6.1.4.1.1751.2.18.29.2.1.2

Integer32

not-accessible

Logical interface number assigned by user

I32 iptPhysicalIntfId

1.3.6.1.4.1.1751.2.18.29.2.1.3

Integer32

read-write

physical interface in SSPPCCC format

INT iptIntfType

1.3.6.1.4.1.1751.2.18.29.2.1.4

INTEGER

read-write

interface primary or secondary.

INT iptOperState

1.3.6.1.4.1.1751.2.18.29.2.1.5

INTEGER

read-only

indicates operational state of the interface.

I32 iptOperatingIntf

1.3.6.1.4.1.1751.2.18.29.2.1.6

Integer32

read-only

protection operational state of the interface. Indicates which logical interface is carrying traffic originally configured for this interface.

INT iptProtCommand

1.3.6.1.4.1.1751.2.18.29.2.1.7

INTEGER

read-write

protection operational state of the interface. Indicates which logical interface is carrying traffic originally configured for this interface.

I32 iptSelectedStandby

1.3.6.1.4.1.1751.2.18.29.2.1.8

Integer32

read-write

Standby interface logical number on which to switch traffic. Used only in case of manual switchover with explicit standby selection.

ROW iptRowStatus

1.3.6.1.4.1.1751.2.18.29.2.1.9

RowStatus

read-write

row status

h248Config

1.3.6.1.4.1.1751.2.18.30

h248TermIdTable

1.3.6.1.4.1.1751.2.18.30.1

not-accessible

Table of H.248 Terminations

h248TermIdEntry

1.3.6.1.4.1.1751.2.18.30.1.1

not-accessible

Row definition for H.248 Termination ID table

INT h248TermSlotId

1.3.6.1.4.1.1751.2.18.30.1.1.1

INTEGER

not-accessible

Slot # for termination

INT h248TermPhyPortId

1.3.6.1.4.1.1751.2.18.30.1.1.2

INTEGER

not-accessible

Physical Port # for termination

INT h248TermLogPortId

1.3.6.1.4.1.1751.2.18.30.1.1.3

INTEGER

not-accessible

Logical Port # for termination

INT h248TermChanId

1.3.6.1.4.1.1751.2.18.30.1.1.4

INTEGER

not-accessible

Chan # for termination

INT h248TermVpi

1.3.6.1.4.1.1751.2.18.30.1.1.5

INTEGER

not-accessible

VPI # for termination. Value 0 is reserved to indicate N/A, e.g., TDM termination. Thus, VPI = h248TermVpi - 1, for h248TermVpi > 0.

INT h248TermVci

1.3.6.1.4.1.1751.2.18.30.1.1.6

INTEGER

not-accessible

VCI # for termination. Value 0 is reserved to indicate N/A, e.g., TDM termination. Thus, VCI = h248TermVci - 1, for h248TermVci > 0.

OCT h248TermId

1.3.6.1.4.1.1751.2.18.30.1.1.7

OCTET STRING

read-write

Termination ID is provisioned by user and used for identifying termination between MGC and MG

INT h248TermAal2Cid

1.3.6.1.4.1.1751.2.18.30.1.1.8

INTEGER

read-write

AAL2 CID

INT h248TermActivation

1.3.6.1.4.1.1751.2.18.30.1.1.9

INTEGER

read-write

Activation for termination ID

ROW h248TermRowStatus

1.3.6.1.4.1.1751.2.18.30.1.1.10

RowStatus

read-write

h248TermIdEntry row status

h248SysControl

1.3.6.1.4.1.1751.2.18.31

I32 h248MaxNumberOfContexts

1.3.6.1.4.1.1751.2.18.31.1

Integer32

read-write

The value of the property gives the maximum number of contexts that can exist at anytime. The NULL context is not included in this number.

I32 h248MaxTerminationsPerContext

1.3.6.1.4.1.1751.2.18.31.2

Integer32

read-write

The max number of terminations allowed in a context.

I32 h248NormalMGExecutionTime

1.3.6.1.4.1.1751.2.18.31.3

Integer32

read-write

Settable by the MGC to indicate the interval within which the MGC expects a response to any transaction from the MG (exclusive of the network delay). Value represents milliseconds.

I32 h248NormalMGCExecutionTime

1.3.6.1.4.1.1751.2.18.31.4

Integer32

read-write

Settable by the MGC to indicate the interval within which the MG expects a response to any transaction from the MG (exclusive of the network delay). Value represents milliseconds.

I32 h248MGProvisionalResponseTimerValue

1.3.6.1.4.1.1751.2.18.31.5

Integer32

read-write

Indicates the time within which the MGC should expect a Pending Response from the MG if a Transaction can not be completed. Initially set to h248NormalMGExecutionTime, plus network delay, but maybe lowered. Value represents milliseconds.

I32 h248MGCProvisionalResponseTimerValue

1.3.6.1.4.1.1751.2.18.31.6

Integer32

read-write

Indicates the time within which the MG should expect a Pending Response from the MGC if a Transaction can not be completed. Initially set to h248NormalMGCExecutionTime, plus network delay, but maybe lowered. Value represents milliseconds.

IP h248MGCIpAddress1

1.3.6.1.4.1.1751.2.18.31.7

IpAddress

read-write

The IP address of the 1st MGC.

IP h248MGCIpAddress2

1.3.6.1.4.1.1751.2.18.31.8

IpAddress

read-write

The IP address of the 2nd MGC.