All MIBs › COMTROL-ES8510-MIB
Organization: Comtrol Corporation
Last Updated: 2018-05-14
Description: Comtrol ES8510 industrial managed Ethernet switch MIB covering VLANs, redundancy, traffic prioritization, multicast filtering, security, and port diagnostics
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is COMTROL-ES8510-MIB?
The COMTROL-ES8510-MIB is a vendor-specific SNMP MIB module for Comtrol Corporation's ES8510 series industrial managed Ethernet switches, used in factory automation and industrial networking environments. It exposes system identification objects (name, location, contact, description), firmware version, MAC address, and switch configuration settings alongside VLAN, redundancy, traffic prioritization, multicast filtering, and security features. It is used to monitor hardware/software status such as firmware version (systemFwVer), device identity (systemMacAddress, systemDescr), and administrative configuration state, giving operators visibility into whether the switch is running expected firmware and is properly configured. It sits under the standard enterprise OID tree (private.enterprises.comtrol) and relies on basic SNMPv2 conventions rather than deep dependency on other standard MIBs. Typical deployment is in industrial control/automation networks (factory floors, process control) where these ruggedized switches interconnect PLCs, sensors, and other OT devices. Engineers can download the COMTROL-ES8510-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in COMTROL-ES8510-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Comtrol ES8510 industrial managed Ethernet switch
Monitoring Examples
An administrator would poll systemFwVer and systemMacAddress to confirm which firmware image and hardware unit is deployed at a given switchSettingSystemLocation, and check switchSettingSystemName/switchSettingSystemContact for asset tracking. Monitoring whether adminPasswordUserName still reflects a default account can flag switches left with factory credentials, a security anomaly. Because objects like switchSettingSystemContact and systemDescr mirror sysContact/sysDescr conventions, a mismatch between systemDescr and the expected model string would indicate a hardware swap or firmware corruption.
What Can Be Monitored
- firmware version
- system MAC address
- system name/location/contact
- administrative account configuration
- switch settings (VLAN, redundancy, prioritization)
This MIB depends on
Related MIBs
Imported Objects
From Q-BRIDGE-MIB
| PortList |
From RFC1155-SMI
| Integer32 | |
| IpAddress | |
| internet |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TimeInterval |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| adminPassword | 1.3.6.1.4.1.2882.2.1.1.2.2 | |||
| STR adminPasswordPassword | 1.3.6.1.4.1.2882.2.1.1.2.2.2 | DisplayString | write-only | The password of security manager. This object can't be read. it's write-only. |
| STR adminPasswordUserName | 1.3.6.1.4.1.2882.2.1.1.2.2.1 | DisplayString | read-write | The name(ID) of security manager. |
| aggregatorSetting | 1.3.6.1.4.1.2882.2.1.1.3.4.1 | |||
| aggregatorStatus | 1.3.6.1.4.1.2882.2.1.1.3.4.2 | |||
| STR backupAgentBoardFwFileName | 1.3.6.1.4.1.2882.2.1.1.2.6.2 | DisplayString | read-write | The filename to backup to. |
| backupAndRestore | 1.3.6.1.4.1.2882.2.1.1.2.6 | |||
| IP backupServerIP | 1.3.6.1.4.1.2882.2.1.1.2.6.1 | IpAddress | read-write | The IP address of a TFTP server to which a startup configuration can be uploaded. |
| INT backupStatus | 1.3.6.1.4.1.2882.2.1.1.2.6.3 | INTEGER | read-write | Setting this object to active(1) trigger the TFTP upload action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read. |
| basicSetting | 1.3.6.1.4.1.2882.2.1.1.2 | |||
| clockSource | 1.3.6.1.4.1.2882.2.1.1.2.4.4 | |||
| clockSourceManual | 1.3.6.1.4.1.2882.2.1.1.2.4.4.2 | |||
| STR clockSourceManualSetting | 1.3.6.1.4.1.2882.2.1.1.2.4.4.2.1 | DisplayString | read-write | set system time, in format yyyy.mm.dd-hh:mm:ss |
| clockSourceNtp | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3 | |||
| INT clockSourceSelection | 1.3.6.1.4.1.2882.2.1.1.2.4.4.1 | INTEGER | read-write | . |
| comtrol | 1.3.6.1.4.1.2882 | |||
| contact | 1.3.6.1.4.1.2882.1 | Comtrol Corporation 100 Fifth Avenue NW New Brighton, MN 55112 TEL: +1.763.957.6000 E-mail: ftpadmin@comtrol.com | ||
| I32 daylightSavingOffset | 1.3.6.1.4.1.2882.2.1.1.2.4.3.3 | Integer32 | read-write | Daylight Saving Offset(Usually is 60 mins). When Enable and current time at Daylight Saving Period, the current time of the switch will be offseted by Daylight Saving Offset. |
| dayLightSavingTime | 1.3.6.1.4.1.2882.2.1.1.2.4.3 | |||
| STR daylightSavingTimeEnd | 1.3.6.1.4.1.2882.2.1.1.2.4.3.2 | DisplayString | read-write | The end-time of daylight saveing period, in format mm.n.d/hh:mm m is month, valid range 1-12 (1=January, 2=February, ..., 12=December). n is week of the month (1 to 5, 5 means the last week). d is weekday, valid range 0-6 (0=Sunday, 1=Monday, ..., 6=Saturday). hh:mm is time. |
| STR daylightSavingTimeStart | 1.3.6.1.4.1.2882.2.1.1.2.4.3.1 | DisplayString | read-write | The start-time of daylight saveing period, in format mm.n.d/hh:mm m is month, valid range 1-12 (1=January, 2=February, ..., 12=December). n is week of the month (1 to 5, 5 means the last week). d is weekday, valid range 0-6 (0=Sunday, 1=Monday, ..., 6=Saturday). hh:mm is time. |
| INT daylightSavingTimeStatus | 1.3.6.1.4.1.2882.2.1.1.2.4.3.4 | INTEGER | read-write | (1)Enable Daylight Saving Time. (2)Disable Daylight Saving Time. Daylight Saving Time: Use this OID to Enable/Disable Daylight Saving Time. |
| dhcpExcludedEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.3.1 | not-accessible | An entry containing DHCP server information of the switch. | |
| I32 dhcpExcludedIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.3.1.1 | Integer32 | not-accessible | The index of the Excluded Table. |
| IP dhcpExcludedIp | 1.3.6.1.4.1.2882.2.1.1.2.5.3.1.2 | IpAddress | read-write | The IP address . |
| ROW dhcpExcludedStatus | 1.3.6.1.4.1.2882.2.1.1.2.5.3.1.3 | RowStatus | read-create | The status of a address pool. |
| dhcpExcludedTable | 1.3.6.1.4.1.2882.2.1.1.2.5.3 | not-accessible | Table of descriptive information and configuration about DHCP server of the switch. | |
| IP dhcpHelperAddress | 1.3.6.1.4.1.2882.2.1.1.2.5.14.1.1 | IpAddress | read-write | The IP address . |
| dhcpHelperAddressEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.14.1 | not-accessible | An entry containing DHCP relay information of the switch. | |
| dhcpHelperAddressTable | 1.3.6.1.4.1.2882.2.1.1.2.5.14 | not-accessible | Table of descriptive information and configuration about DHCP relay helper address of the switch. | |
| dhcpManualBindingEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1 | not-accessible | An entry containing DHCP server information of the switch. | |
| I32 dhcpManualBindingIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1.1 | Integer32 | not-accessible | The index of the Static Binding Table. |
| IP dhcpManualBindingIp | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1.2 | IpAddress | read-write | The IP address. |
| MAC dhcpManualBindingMac | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1.3 | MacAddress | read-write | The MAC address. |
| ROW dhcpManualBindingStatus | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1.4 | RowStatus | read-create | The status of the binding. |
| dhcpManualBindingTable | 1.3.6.1.4.1.2882.2.1.1.2.5.4 | not-accessible | Table of descriptive information and configuration about DHCP server of the switch. | |
| INT dhcpOption82CircuitIdType | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.2 | INTEGER | read-write | The Circuit-ID type of this option. |
| OCT dhcpOption82CircuitIdValue | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.3 | OCTET STRING | read-write | The Circuit-ID value of this option. |
| dhcpOption82Entry | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1 | not-accessible | DHCP server option82 entry. | |
| I32 dhcpOption82Index | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.1 | Integer32 | not-accessible | The index of the table. |
| IP dhcpOption82Ip | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.6 | IpAddress | read-write | The IP Address bind to this option. |
| INT dhcpOption82RemoteIdType | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.4 | INTEGER | read-write | The Remote-ID type of this option. |
| OCT dhcpOption82RemoteIdValue | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.5 | OCTET STRING | read-write | The Remote-ID value of this option. |
| ROW dhcpOption82Status | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.7 | RowStatus | read-create | he status of a static port entry. |
| dhcpOption82Table | 1.3.6.1.4.1.2882.2.1.1.2.5.6 | not-accessible | DHCP server option82 table. | |
| OCT dhcpRelayAgentCircuitIdDisplay | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1.4 | OCTET STRING | read-only | Display the Circuit-ID value by Hexadecimal format |
| dhcpRelayAgentCircuitIdEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1 | not-accessible | Description. | |
| I32 dhcpRelayAgentCircuitIdPortNum | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1.1 | Integer32 | read-only | Description. |
| dhcpRelayAgentCircuitIdTable | 1.3.6.1.4.1.2882.2.1.1.2.5.10 | not-accessible | Description. | |
| INT dhcpRelayAgentCircuitIdType | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1.2 | INTEGER | read-write | Circuit-ID type of the Option82 added by Relay Agent. |
| OCT dhcpRelayAgentCircuitIdValue | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1.3 | OCTET STRING | read-write | Circuit-ID value of the Option82 added by Relay Agent, the format can be String or Hexadecimal value. |
| INT dhcpRelayAgentEnable | 1.3.6.1.4.1.2882.2.1.1.2.5.8 | INTEGER | read-write | Enable or disable dhcp relay agent function. |
| INT dhcpRelayAgentPolicy | 1.3.6.1.4.1.2882.2.1.1.2.5.9 | INTEGER | read-write | Keep(1): Keeps the original option 82 field and forwards to server drop(2): Drops the option 82 field and do not add any option 82 field replace(3): Replaces the existing option 82 field and adds new option 82 field. (This is the default setting) |
| OCT dhcpRelayAgentRemoteIdDisplay | 1.3.6.1.4.1.2882.2.1.1.2.5.13 | OCTET STRING | read-write | Remote-ID value of the Option82 added by Relay Agent. |
| INT dhcpRelayAgentRemoteIdType | 1.3.6.1.4.1.2882.2.1.1.2.5.11 | INTEGER | read-write | Remote-ID type of the Option82 added by Relay Agent. |
| OCT dhcpRelayAgentRemoteIdValue | 1.3.6.1.4.1.2882.2.1.1.2.5.12 | OCTET STRING | read-write | Remote-ID value of the Option82 added by Relay Agent, the format can be String or Hexadecimal value. |
| dhcpServer | 1.3.6.1.4.1.2882.2.1.1.2.5 | |||
| INT dhcpServerEnable | 1.3.6.1.4.1.2882.2.1.1.2.5.1 | INTEGER | read-write | Enable or disable dhcp server function. |
| dhcpServerLeasedEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1 | not-accessible | An entry containing DHCP server information of the switch. | |
| I32 dhcpServerLeasedIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.1 | Integer32 | not-accessible | The index of the Leased Table. |
| IP dhcpServerLeasedIp | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.2 | IpAddress | read-only | The client IP address. |
| MAC dhcpServerLeasedMac | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.3 | MacAddress | read-only | The client MAC address. |
| dhcpServerLeasedTable | 1.3.6.1.4.1.2882.2.1.1.2.5.7 | not-accessible | Table of descriptive information and configuration about DHCP server of the switch. | |
| I32 dhcpServerLeasedTime | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.5 | Integer32 | read-only | The lease time of the client. |
| INT dhcpServerLeasedType | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.4 | INTEGER | read-only | . |
| dhcpServerPoolEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1 | not-accessible | An entry containing DHCP server information of the switch. | |
| IP dhcpServerPoolGateway | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.5 | IpAddress | read-write | The gateway address of the IP Address Pool. |
| I32 dhcpServerPoolIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.1 | Integer32 | not-accessible | The index of the Address Pool. |
| I32 dhcpServerPoolLeaseTime | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.6 | Integer32 | read-write | The lease time(in second) of the Address Pool. |
| STR dhcpServerPoolName | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.2 | DisplayString | read-only | The address pool name. |
| IP dhcpServerPoolNetwork | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.3 | IpAddress | read-write | The Subnet of the IP Address Pool. |
| ROW dhcpServerPoolStatus | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.7 | RowStatus | read-create | The status of the Address Pool. |
| IP dhcpServerPoolSubMask | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.4 | IpAddress | read-write | The subnet mask of the IP Address Pool. |
| dhcpServerPoolTable | 1.3.6.1.4.1.2882.2.1.1.2.5.2 | not-accessible | Table of descriptive information and configuration about DHCP server of the switch. | |
| dhcpStaticPortEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1 | not-accessible | An entry containing DHCP server information of the switch. | |
| I32 dhcpStaticPortIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1.1 | Integer32 | not-accessible | The index of the StaticPort Table. |
| IP dhcpStaticPortIp | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1.3 | IpAddress | read-write | The IP address . |
| INT dhcpStaticPortNumber | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1.2 | INTEGER | read-write | The port number . |
| ROW dhcpStaticPortStatus | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1.4 | RowStatus | read-create | The status of a static port entry. |
| dhcpStaticPortTable | 1.3.6.1.4.1.2882.2.1.1.2.5.5 | not-accessible | Table of descriptive information and configuration about DHCP server of the switch. | |
| INT diConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.3 | INTEGER | read-write | The fault relay will be triggered if digital input is low or high. |
| dot1qGvrp | 1.3.6.1.4.1.2882.2.1.1.5.2.3 | |||
| INT dot1qGvrpStatus | 1.3.6.1.4.1.2882.2.1.1.5.2.3.1 | INTEGER | read-write | Enable GVRP Protocol. |
| INT dot1qPortAcceptableFrameTypes | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1.3 | INTEGER | read-write | When admitOnlyVlanTagged(2) the device will discard untagged frames or Priority-Tagged only frames received on this port. When admitAll(1), untagged frames or Priority-Tagged only frames received on this port will be accepted and assigned the PVID for this frame. This control does not affect VLAN independent BPDU frames, such as SuperRing, STP, GVRP and LACP. It does affect VLAN dependent BPDU frames, such as GMRP. |
| NUM dot1qPortGarpJoinTimer | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.3 | TimeInterval | read-write | The GARP Join timer, in centiseconds. |
| NUM dot1qPortGarpLeaveAllTimer | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.5 | TimeInterval | read-write | The GARP LeaveAll time, in centiseconds. |
| NUM dot1qPortGarpLeaveTimer | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.4 | TimeInterval | read-write | The GARP Leave time, in centiseconds. |
| dot1qPortGvrpEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1 | not-accessible | Information controlling GVRP configuration for a port on the device. | |
| INT dot1qPortGvrpIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.1 | INTEGER | not-accessible | The port identifier. |
| INT dot1qPortGvrpStatus | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.2 | INTEGER | read-write | The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port. |
| dot1qPortGvrpTable | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2 | not-accessible | A table containing per port control and status information for GVRP configuration in the device. | |
| INT dot1qPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1.1 | INTEGER | read-only | The port identifier. |
| INT dot1qPortIngressFiltering | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1.4 | INTEGER | read-write | When true(1) the device will discard incoming frames whose VLAN classification do not include this port in its Member set. When false(2), the port will accept all incoming frames regardless its VLAN classification. This control does not affect VLAN independent BPDU frames, such as SuperRing, STP, GVRP and LACP. It does affect VLAN dependent BPDU frames, such as GMRP. |
| dot1qPortVlanEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1 | not-accessible | Information controlling IEEE802.1Q VLAN configuration for a port on the device. | |
| dot1qPortVlanTable | 1.3.6.1.4.1.2882.2.1.1.5.2.1 | not-accessible | A table containing per port control and status information for IEEE802.1Q VLAN configuration in the device. | |
| INT dot1qPvid | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1.2 | INTEGER | read-write | The default Port VID, the VLAN ID assigned to an untagged frame or a Priority-Tagged frame received on the port. |
| dot1qTunnel | 1.3.6.1.4.1.2882.2.1.1.5.2.5 | |||
| OCT dot1qTunnelEtherType | 1.3.6.1.4.1.2882.2.1.1.5.2.5.1 | OCTET STRING | read-write | ethertype/TPID |
| dot1qTunnelPortEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.5.2.1 | not-accessible | Information controlling tunnel configuration for a port on the device. | |
| INT dot1qTunnelPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.5.2.1.1 | INTEGER | not-accessible | The port identifier. |
| INT dot1qTunnelPortMode | 1.3.6.1.4.1.2882.2.1.1.5.2.5.2.1.2 | INTEGER | read-write | Tunnel mode controls |
| dot1qTunnelPortTable | 1.3.6.1.4.1.2882.2.1.1.5.2.5.2 | not-accessible | A table containing per tunnel access or uplink port information in the device. | |
| POR dot1qVlanCurrentEgressPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1.2 | PortList | read-only | The set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames. |
| dot1qVlanCurrentEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1 | not-accessible | Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received. | |
| INT dot1qVlanCurrentIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1.1 | INTEGER | read-only | The VLAN Identifier (VID) refering to this VLAN. |
| dot1qVlanCurrentTable | 1.3.6.1.4.1.2882.2.1.1.5.2.4 | not-accessible | A table containing information about currently configured VLANs, either by (local or network) management, or dynamically created as a result of GVRP requests received. | |
| POR dot1qVlanCurrentUntaggedPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1.3 | PortList | read-only | The set of ports which are transmitting traffic for this VLAN as untagged frames. |
| INT dot1qVlanIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.1 | INTEGER | read-only | The VLAN Identifier (VID) refering to this VLAN. The valid range is from 1 to 4094. |
| POR dot1qVlanStaticEgressPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.3 | PortList | read-only | The set of ports which are permanently configured to transmitting traffic for this VLAN as either tagged or untagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros, indicating not fixed. |
| dot1qVlanStaticEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1 | not-accessible | Static information of a VLAN configured into the device by management. | |
| STR dot1qVlanStaticName | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.2 | DisplayString | read-write | An administratively assigned string, which is used to identify the VLAN. |
| ROW dot1qVlanStaticRowStatus | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.6 | RowStatus | read-create | This object is used to manage to creation and deletion of a VLAN, and is used to indicate the status of this entry. To Creating and activate a VLAN, first select a unused VID for dot1qVlanIndex and then set its dot1qVlanStaticRowStatus to 'createAndGo'. The VLAN will be created in the device without tagged or untagged ports. A default VLAN name is assigned and the status is set to 'active'. To configure tagged and untagged port members of the VLAN, assign appropriate of dot1qVlanStaticTaggedPorts and dot1qVlanStaticUntaggedPorts. A set operation takes effect on the device immediately. To delete a VLAN, select the VID for dot1qVlanIndex and set dot1qVlanStaticRowStatus to 'destory'. The row and the corresponding VLAN configurarion will be removed from the device. VLAN 1 is the default VLAN and can never be deleted. All untagged traffic falls into this VLAN by default. 'createAndWait', 'notInService', 'notReady' have no effects. |
| dot1qVlanStaticTable | 1.3.6.1.4.1.2882.2.1.1.5.2.2 | not-accessible | A table containing configuration information for each VLAN configured into the device by management. All entries are permanent and will be restored after the device is reset. Upto 64 VLANs can be configured in this device. IEEE 802.1Q Virtual LANs (VLANs) allow a single physical LAN to be partitioned into several smaller logical LANs. VLANs limit the broadcast domain, improve security and performance and are ideal for separating systems or departments from each other. | |
| POR dot1qVlanStaticTaggedPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.5 | PortList | read-create | The set of ports which are permanently configured to transmitting traffic for this VLAN as tagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object for the default VLAN is a portlist including all ports. There is no specified default for other VLANs. |
| POR dot1qVlanStaticUntaggedPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.4 | PortList | read-create | The set of ports which are permanently configured to transmitting traffic for this VLAN as untagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object for the default VLAN is a portlist including all ports. There is no specified default for other VLANs. |
| INT dot1qVlanStatus | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1.4 | INTEGER | read-only | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. permanent(2) - this entry, corresponding to an entry in dot1qVlanStaticTable, is currently in use and will remain so after the next reset of the device. The port lists for this entry include ports from the equivalent dot1qVlanStaticTable entry and ports learnt dynamically. dynamicGvrp(3) - this entry is currently in use and will remain so until removed by GVRP. There is no static entry for this VLAN and it will be removed when the last port leaves the VLAN. |
| dot1x | 1.3.6.1.4.1.2882.2.1.1.9.3 | |||
| INT dot1xAuthentication | 1.3.6.1.4.1.2882.2.1.1.9.3.2 | INTEGER | read-write | . |
| dot1xLocalUserEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1 | not-accessible | . | |
| I32 dot1xLocalUserIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1.1 | Integer32 | not-accessible | . |
| STR dot1xLocalUserName | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1.2 | DisplayString | read-write | set this field to empty to remove this user config. |
| STR dot1xLocalUserPassword | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1.3 | DisplayString | read-write | . |
| dot1xLocalUserTable | 1.3.6.1.4.1.2882.2.1.1.9.3.4 | not-accessible | . | |
| I32 dot1xLocalUserVid | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1.4 | Integer32 | read-write | . |
| INT dot1xPortAdminDirection | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.7 | INTEGER | read-write | . |
| INT dot1xPortAuthControl | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.2 | INTEGER | read-write | . |
| INT dot1xPortAuthStatus | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.3 | INTEGER | read-only | . |
| MAC dot1xPortAuthSupplicant | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.4 | MacAddress | read-only | . |
| INT dot1xPortClientReauth | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.10 | INTEGER | write-only | . |
| dot1xPortConfigEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1 | not-accessible | . | |
| I32 dot1xPortConfigIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.1 | Integer32 | not-accessible | . |
| INT dot1xPortConfigSetDefault | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.8 | INTEGER | read-write | . |
| dot1xPortConfigTable | 1.3.6.1.4.1.2882.2.1.1.9.3.5 | not-accessible | . | |
| INT dot1xPortCtrl | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.2 | INTEGER | read-only | . |
| INT dot1xPortGuestVlan | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.5 | INTEGER | read-write | . |
| INT dot1xPortHostMode | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.6 | INTEGER | read-write | . |
| INT dot1xPortMaxRequest | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.4 | INTEGER | read-write | . |
| INT dot1xPortOperDirection | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.5 | INTEGER | read-only | . |
| I32 dot1xPortQuietPeriod | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.3 | Integer32 | read-write | . |
| INT dot1xPortReauthentication | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.3 | INTEGER | read-write | . |
| I32 dot1xPortReauthPeriod | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.2 | Integer32 | read-write | . |
| INT dot1xPortReinitialize | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.9 | INTEGER | read-write | . |
| I32 dot1xPortServerTimeout | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.6 | Integer32 | read-write | . |
| dot1xPortStatusEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1 | not-accessible | . | |
| I32 dot1xPortStatusIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.1 | Integer32 | not-accessible | . |
| dot1xPortStatusTable | 1.3.6.1.4.1.2882.2.1.1.9.3.7 | not-accessible | . | |
| I32 dot1xPortSupplicantTimeout | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.5 | Integer32 | read-write | . |
| dot1xPortTimeoutConfigEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1 | not-accessible | . | |
| dot1xPortTimeoutConfigTable | 1.3.6.1.4.1.2882.2.1.1.9.3.6 | not-accessible | . | |
| I32 dot1xPortTimeoutIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.1 | Integer32 | not-accessible | . |
| I32 dot1xPortTxPeriod | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.4 | Integer32 | read-write | . |
| INT dot1xStatus | 1.3.6.1.4.1.2882.2.1.1.9.3.1 | INTEGER | read-write | IEEE802.1x protocol function status. (1) IEEE802.1x protocol function is enabled. (2) IEEE802.1x protocol function is disabled. 802.1x makes use of the physical access characteristics of IEEE802 LAN infrastructures in order to provide a means of authenticating and authorizing devices attached to a LAN port that has point-to-point connection characteristics, and of preventing access to that port in cases in which the authentication and authorization process fails. |
| INT dryOutputOffPeriodConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.5 | INTEGER | read-write | The fault relay will be opened after a period (in seconds). Together with dryOutputOnPeriodConfig, the fault relay can be configured to continue on and off. |
| INT dryOutputOnPeriodConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.4 | INTEGER | read-write | The fault relay will be closed after a period (in seconds). Together with dryOutputOffPeriodConfig, the fault relay can be configured to continue on and off. |
| emailAlertRcptEntry | 1.3.6.1.4.1.2882.2.1.1.10.2.3.7.1 | not-accessible | An entry containing recipient email address. | |
| emailAlertRcptTable | 1.3.6.1.4.1.2882.2.1.1.10.2.3.7 | not-accessible | Table configuring recipient email addresses. | |
| enterprises | 1.3.6.1.4.1 | |||
| es8510 | 1.3.6.1.4.1.2882.2.1.1 | |||
| eventAndEmailWarning | 1.3.6.1.4.1.2882.2.1.1.10.2 | |||
| ALE eventAuthenticationFailureEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.4 | AlertType | read-write | Select which warning machanism to take place when authentication failure. |
| ALE eventDeviceColdStartEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.2 | AlertType | read-write | Select which warning machanism to take place when the device cold starts. |
| ALE eventDeviceWarmStartEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.3 | AlertType | read-write | Select which warning machanism to take place when the device warm starts. |
| ALE eventDI1ChangeEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.11 | AlertType | read-write | Select which warning machanism to take place when DI1 changed . |
| ALE eventDI2ChangeEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.12 | AlertType | read-write | Select which warning machanism to take place when DI2 changed . |
| STR eventEmailAlertAccount | 1.3.6.1.4.1.2882.2.1.1.10.2.3.3 | DisplayString | read-write | The email account for SMTP server. It can't be modified when eventEmailAlertAuthentication is disabled. |
| INT eventEmailAlertAuthentication | 1.3.6.1.4.1.2882.2.1.1.10.2.3.4 | INTEGER | read-write | Set to (1)enabled if it needs authentication to connect to the SMTP server. It can't be modified when eventEmailAlertStatus is disabled. |
| STR eventEmailAlertPassword | 1.3.6.1.4.1.2882.2.1.1.10.2.3.6 | DisplayString | write-only | The password of email account. It can't be modified when eventEmailAlertAuthentication is disabled. |
| STR eventEmailAlertRcptEmailAddr | 1.3.6.1.4.1.2882.2.1.1.10.2.3.7.1.2 | DisplayString | read-write | A recipient email address. |
| I32 eventEmailAlertRcptIndex | 1.3.6.1.4.1.2882.2.1.1.10.2.3.7.1.1 | Integer32 | not-accessible | Index of recipient Email address. |
| IP eventEmailAlertServer | 1.3.6.1.4.1.2882.2.1.1.10.2.3.2 | IpAddress | read-write | The IP address of SMTP server. It can't be modified when eventEmailAlertStatus is disabled. |
| INT eventEmailAlertStatus | 1.3.6.1.4.1.2882.2.1.1.10.2.3.1 | INTEGER | read-write | Parameter to enable the email alert feature, When enabled, the switch will send an email to the address presented in emailAlertRcptTable. |
| STR eventEmailAlertUser | 1.3.6.1.4.1.2882.2.1.1.10.2.3.5 | DisplayString | read-write | The email account for SMTP server. It can't be modified when eventEmailAlertAuthentication is disabled. |
| ALE eventFaultRelayEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.8 | AlertType | read-write | Select which warning machanism to take place when a fault relay is triggered. |
| eventLog | 1.3.6.1.4.1.2882.2.1.1.11.4 | |||
| INT eventLogClear | 1.3.6.1.4.1.2882.2.1.1.11.4.1 | INTEGER | read-write | clear all event log. |
| STR eventLogDescription | 1.3.6.1.4.1.2882.2.1.1.11.4.2.1.2 | DisplayString | read-only | The description of a log. |
| eventLogEntry | 1.3.6.1.4.1.2882.2.1.1.11.4.2.1 | not-accessible | An entry in the table containing a log. | |
| I32 eventLogIndex | 1.3.6.1.4.1.2882.2.1.1.11.4.2.1.1 | Integer32 | read-only | Index of log. |
| eventLogTable | 1.3.6.1.4.1.2882.2.1.1.11.4.2 | not-accessible | Table of descriptive information about logs. | |
| ALE eventLoopDetectionEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.13 | AlertType | read-write | Select which warning machanism to take place when loop detection event occured. |
| INT eventPortEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.2.1.2 | INTEGER | read-write | Select the port event to react to. |
| I32 eventPortNumber | 1.3.6.1.4.1.2882.2.1.1.10.2.1.2.1.1 | Integer32 | read-only | Port number. |
| ALE eventPower1FailureEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.6 | AlertType | read-write | Select which warning machanism to take place when power1 failure. |
| ALE eventPower2FailureEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.7 | AlertType | read-write | Select which warning machanism to take place when power2 failure. |
| ALE eventRingEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.5 | AlertType | read-write | Select which warning machanism to take place when ring event occured. |
| eventSelection | 1.3.6.1.4.1.2882.2.1.1.10.2.1 | |||
| ALE eventSFPEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.10 | AlertType | read-write | Select which warning machanism to take place when SFP event occured. |
| I32 eventSystemEventIndex | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.1 | Integer32 | not-accessible | Index of events. |
| ALE eventTimeSynchronizeEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.9 | AlertType | read-write | Select which warning machanism to take place when time synchronizatonn failed. |
| factoryDefault | 1.3.6.1.4.1.2882.2.1.1.2.8 | |||
| INT factoryDefaultActive | 1.3.6.1.4.1.2882.2.1.1.2.8.1 | INTEGER | read-write | Set to active(1) to reload factory default configuration. Reloading factory default will overwrite your current configuration file with factocy default configuration while current IP configuration is reserved. Please reboot the device to make factory default configuration take effect. Set notActive(2) has no effect. The system always returns the value notActive(2) when this object is read. |
| faultRelay | 1.3.6.1.4.1.2882.2.1.1.10.1 | |||
| faultRelayEntry | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1 | not-accessible | A entry controlling a fault relay configuration. | |
| INT faultRelayEntryStatus | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.11 | INTEGER | read-write | Setting this object to active(1) to save the configuration to the device. Setting this object to notActive(3) disable the configuration. The system returns active(1) or notActive when the settings of the entry is enabled or disabled on the relay. And the status becomes configuring(2) when the settings of the entry are modified and not set to active(1) yet. |
| INT faultRelayId | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.1 | INTEGER | read-only | Index of fault relay. |
| faultRelayTable | 1.3.6.1.4.1.2882.2.1.1.10.1.1 | not-accessible | Table of configuration about fault relay. A fault relay is able to control an output circuit which is triggered by management defined fault events. There are two fault relays in the device, each is controlled by an faultRelayEntry in this table. To configure a fault relay, first select the type of fault event which will trigger the relay in faultSelection, and then configure the related column. Set faultRelayEntryStatus to active(1) to set the configuration to the device. | |
| INT faultSelection | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.2 | INTEGER | read-write | Select the type of fault event that triggers the relay. To config a fault relay, first select the founction this relay serves for, then configure the condition that triggers the relay in detail. At last, set the faultRelayEntryStatus to active(1) or nonActive(3) to enable or disable the setting on the relay. |
| hardwareStatus | 1.3.6.1.4.1.2882.2.1.1.10.3 | |||
| hardwareStatusEntry | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1 | read-only | ||
| hardwareStatusTable | 1.3.6.1.4.1.2882.2.1.1.10.3.1 | not-accessible | ||
| ieee8021qVlan | 1.3.6.1.4.1.2882.2.1.1.5.2 | |||
| igmpQuery | 1.3.6.1.4.1.2882.2.1.1.7.1 | |||
| I32 igmpQueryInterval | 1.3.6.1.4.1.2882.2.1.1.7.1.3 | Integer32 | read-write | The interval between General Queries sent by this Querier in seconds. |
| I32 igmpQueryMaxResponseTime | 1.3.6.1.4.1.2882.2.1.1.7.1.4 | Integer32 | read-write | Max Respocse Time is meaningful only in Membership Query messages, and specifies the maximum allowed time before sending a responding report in seconds. |
| INT igmpQueryStatus | 1.3.6.1.4.1.2882.2.1.1.7.1.2 | INTEGER | read-write | (1)enable IGMP Query on management vlan. (2)disable IGMP Query. |
| INT igmpQueryVersion | 1.3.6.1.4.1.2882.2.1.1.7.1.1 | INTEGER | read-write | (1)IGMP Query version 1. (2)IGMP Query version 2. |
| igmpSnooping | 1.3.6.1.4.1.2882.2.1.1.7.2 | |||
| igmpSnoopingEntry | 1.3.6.1.4.1.2882.2.1.1.7.2.2.1 | not-accessible | Inforamtion enabling or disabling IGMP snooping on a vlan. | |
| INT igmpSnoopingEntryStatus | 1.3.6.1.4.1.2882.2.1.1.7.2.2.1.2 | INTEGER | read-write | The state of igmp snooping functionality on a vlan. Set to enabled(1) indicates that igmp snooping is enabled on the vlan. When igmpSnoopingStatus is also turned on, each IGMP packets on the vlan will be processed. When disabled(2) with igmpSnoopingStatus enabled, igmp packets will not be processed and be propagated to other member ports of the vlan. A transition from disabled(2) to enabled(1) will cause a reset of all igmp snooping information on this vlan. |
| INT igmpSnoopingEntryVID | 1.3.6.1.4.1.2882.2.1.1.7.2.2.1.1 | INTEGER | read-only | The vlan id. |
| igmpSnoopingGroupEntry | 1.3.6.1.4.1.2882.2.1.1.7.2.3.1 | not-accessible | Information containing a multicast group and its member ports. | |
| IP igmpSnoopingGroupEntryIPAddr | 1.3.6.1.4.1.2882.2.1.1.7.2.3.1.2 | IpAddress | read-only | The multicast group IP address. |
| POR igmpSnoopingGroupEntryMembers | 1.3.6.1.4.1.2882.2.1.1.7.2.3.1.3 | PortList | read-only | The member ports of the group. |
| INT igmpSnoopingGroupEntryVID | 1.3.6.1.4.1.2882.2.1.1.7.2.3.1.1 | INTEGER | read-only | The VLAN ID of an IGMP entry. |
| igmpSnoopingGroupTable | 1.3.6.1.4.1.2882.2.1.1.7.2.3 | not-accessible | Table of descriptive information about IGMP snooped multicast groups. | |
| INT igmpSnoopingStatus | 1.3.6.1.4.1.2882.2.1.1.7.2.1 | INTEGER | read-write | Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for multicast traffic. The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP makes the device to gather multicast group membership information by snooping IGMP packets, which helps the device switch IP multicast traffic to the ports where group members exist instead of flooding the traffic to every ports. IGMP have three fundamental types of message as follows: Message Description -------------------------------------------------------------- Query A message sent from the querier (IGMP router or switch) asking for responses from each host belonging to a multicast group. Report A message sent by a host to the querier to indicate that the host wants to be or is a member of a given group indicated in the report message. Leave A message sent by a host to the querier to indicate that the host has quit to be a member for a specific multicast group. The IGMP snooping functionality is configured on a vlan basis. To enable or disable IGMP snooping on vlans: 1. set igmpSnoopingStatus to enable(1) or disable(2). 2. specify on which vlan IGMP snooping works by configuring each entries in the igmpSnoopingTable. As a result, you can turn on or off IGMP snooping functionality by setting igmpSnoopingStatus while keeping the configuration for each vlan. Or you can turn on or off IGMP snooping for a specific vlan in igmpSnoopingTable with the statuses on other vlan untouched. |
| igmpSnoopingTable | 1.3.6.1.4.1.2882.2.1.1.7.2.2 | not-accessible | Table of descriptive information about on which vlan is IGMP snooping enabled. | |
| ipConfiguration | 1.3.6.1.4.1.2882.2.1.1.2.3 | |||
| IP ipConfigurationAddress | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.3 | IpAddress | read-write | The IP address of switch. An IP address (Internet Protocol address) is a unique address that devices use in order to identify and communicate with each other on a computer network utilizing the Internet Protocol standard (IP). Any participating network device can has its own unique address. |
| INT ipConfigurationDHCPStatus | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.2 | INTEGER | read-write | Parameter configuring DHCP client functionality of the device. When enabled, device will be a DHCP client and request for the IP configuration from DHCP server. The Dynamic Host Configuration Protocol (DHCP) automates the assignment of IP addresses, subnet masks, default routers, and other IP parameters. The assignment usually occurs when the DHCP-configured machine boots up or regains connectivity to the network. The DHCP client sends out a query requesting a response from a DHCP server on the locally attached network. The query is typically initiated immediately after booting up and before the client initiates any IP based communication with other hosts. The DHCP server then replies to the client with its assigned IP address, subnet mask, DNS server and default gateway information. Note: Other items in this table will not be modified, when ipConfigurationDHCPStatus is enabled. |
| IP ipConfigurationDNS1 | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.6 | IpAddress | read-write | Parameter configuring the first DNS server of the device. The domain name system (DNS) stores and associates many types of information with domain names. Most importantly, it translates domain names (computer hostnames) to IP addresses, which makes it possible to attach easy-to-remember domain names to hard-to-remember IP addresses (such as 100.50.10.100). |
| IP ipConfigurationDNS2 | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.7 | IpAddress | read-write | Parameter configuring the second DNS server of the device. |
| ipConfigurationEntry | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1 | not-accessible | Information configuring static IP or DHCP configuration of the device. | |
| IP ipConfigurationGateway | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.5 | IpAddress | read-write | The default gateway IP address identifies the gateway (for example, a router) that receives and forwards those packets whose addresses are unknown to the local network. The agent uses the default gateway address when sending alert packets to the management workstation on a network other than the local network. |
| INT ipConfigurationIndex | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.1 | INTEGER | not-accessible | This object identifies IP configuration entries. |
| ROW ipConfigurationStatus | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.8 | RowStatus | read-create | The status of the IP configuration entry. Only one configuration entry is supported on the device. Set active(1) to activate the parameters of the entry on the device. |
| IP ipConfigurationSubMask | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.4 | IpAddress | read-write | The subnet mask is a 32-bit number in the same format and representation as IP addresses. The subnet mask determines which bits in the IP address are interpreted as the network number, which as the subnetwork number, and which as the host number. Each IP address bit that corresponds to a 1 in the subnet mask is in the network/subnetwork part of the address. This group of numbers is also called the Network ID. Each IP address bit that corresponds to a 0 is in the host part of the IP address. |
| ipConfigurationTable | 1.3.6.1.4.1.2882.2.1.1.2.3.1 | not-accessible | Table of descriptive information and configuration about the IP of the device. | |
| ipSecurity | 1.3.6.1.4.1.2882.2.1.1.9.2 | |||
| ipSecurityEntry | 1.3.6.1.4.1.2882.2.1.1.9.2.2.1 | not-accessible | An entry configuring an security IP address. | |
| I32 ipSecurityIndex | 1.3.6.1.4.1.2882.2.1.1.9.2.2.1.1 | Integer32 | not-accessible | Index of IP address entry. |
| IP ipSecurityIP | 1.3.6.1.4.1.2882.2.1.1.9.2.2.1.2 | IpAddress | read-write | An IP address that can access and manage the device. |
| ROW ipSecurityRowStatus | 1.3.6.1.4.1.2882.2.1.1.9.2.2.1.3 | RowStatus | read-create | This object is used to manage to creation and deletion of a authorized IP address, and is used to indicate the status of this entry. A empty entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory. |
| INT ipSecurityStatus | 1.3.6.1.4.1.2882.2.1.1.9.2.1 | INTEGER | read-write | Enable or disable IP security functionality. IP security allows you to assign specific IP addresses that are permitted to access the device for securing switch management. Set to (1) to enable IP Security. set to (2) to disable IP Security. Enabling IP Security without any entries configured in the ipSecurityTable has no effect on the access traffic. |
| ipSecurityTable | 1.3.6.1.4.1.2882.2.1.1.9.2.2 | not-accessible | Table configuring IP addresses that can access and manage the device through network, such as telnet, web or SNMP. Please note that enabling IP security function but without adding the IP address of your current management station will break current management connection. | |
| INT ledDI1Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.6 | INTEGER | read-only | |
| INT ledDI2Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.7 | INTEGER | read-only | |
| INT ledDO1Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.4 | INTEGER | read-only | |
| INT ledDO2Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.5 | INTEGER | read-only | |
| I32 ledHardwareStatusIndex | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.1 | Integer32 | not-accessible | Index of leds. |
| INT ledPower1Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.2 | INTEGER | read-only | |
| INT ledPower2Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.3 | INTEGER | read-only | |
| INT ledRMStatus | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.8 | INTEGER | read-only | |
| POR linkFailureConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.7 | PortList | read-write | The fault relay will be trigger if any of the configured links fails. |
| macAddrEntry | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1 | not-accessible | An entry containing inforamtion about a MAC address entry. | |
| MAC macAddressAddr | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.1 | MacAddress | read-write | MAC address of the entry. |
| POR macAddressPortList | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.3 | PortList | read-write | The port list, which must be valid when creating a new entry. |
| ROW macAddressStatus | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.5 | RowStatus | read-create | This object is used to manage to creation and deletion of a static entry, and is used to indicate the status of an entry. To Creating a static entry, select a unused value of macAddressIndex and set macAddressStatus to 'createAndWait'. A row will then be created with status set to 'notReady' and its macAddressType, macAddressPortList and macAddressVlanId left unspecified. macAddressType, macAddressPortList and macAddressVlanId are mandatory to activate an entry to the device. macAddressStatus remains 'notReady' if any of these three objects are invalid. macAddressStatus will be changed to 'notInService' when the three objects are correctly configured. Set macAddressStatus to 'active' to activate the MAC entry to the device. Static unicast and multicast entries and dynamic unicast entries are removable. To delete a MAC entry, select the macAddressIndex set macAddressStatus to 'destory'. The row and the corresponding MAC address configurarion will be removed from the device. Set macAddressStatus to 'createAndGo', 'notInService', 'notReady' have no effects. |
| macAddressTable | 1.3.6.1.4.1.2882.2.1.1.11.1 | |||
| INT macAddressType | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.2 | INTEGER | read-write | The type of this entry. dynamicUnicast(1) - unicast address that learned from source address of ingress frames. staticUnicast(2) - unicast address that configured by management and will remain so after the next reset of the device. Upto 10 static unicast entries can be configured for each port. managementUnicast(3) - unicast address that configured for management purpose or the MAC address of the device itself. Management unicast entries are read-only. dynamicMulticast(4) - dynamic multicast address that configured by IGMP snooping. These entries are read-only. staticMulticast(5) - multicast address that configured by management and will remain so after the next reset of the device. -- Upto 10 static multicast entries can be configured. managementMulticast(6) - multicast address that configured for management purpose, such as GVRP and so on. These entries are read-only. Management entries are read-only. Dynamic entries can be read and delete. Only static entries are read-create. |
| I32 macAddressVlanId | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.4 | Integer32 | read-write | The VLAN where the mac address learned from or configured to. |
| macAddrTable | 1.3.6.1.4.1.2882.2.1.1.11.1.1 | not-accessible | A table containing information about unicast or multicast MAC addresses that currently learned, configured by management or IGMP snooping. | |
| INT macAddrTableAgingTime | 1.3.6.1.4.1.2882.2.1.1.11.1.3 | INTEGER | read-write | This value determines the interval that an automatic learned MAC address entry remains valid in the forwarding database, since its last access as a source address, before being purged. The value should be times of 15 in seconds. The minimum age time is 15 seconds. The maximum age time is 3825 seconds or almost 64 minutes. if the value is set to 0, the aging function is disabled and all learned address will remain in the database forever. |
| INT macAddrTableClear | 1.3.6.1.4.1.2882.2.1.1.11.1.2 | INTEGER | read-write | Set to clear for cleaning all the dynamic MAC entries in the MAC address table. |
| managedSwitch | 1.3.6.1.4.1.2882.2.1 | |||
| monitorandDiag | 1.3.6.1.4.1.2882.2.1.1.11 | |||
| mstp | 1.3.6.1.4.1.2882.2.1.1.4.7 | |||
| mstpBridgeInformation | 1.3.6.1.4.1.2882.2.1.1.4.8 | |||
| mstpPerInstCfgEntry | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1 | not-accessible | Information configuring MSTP on a instance. | |
| I32 mstpPerInstCfgInstanceID | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1.1 | Integer32 | not-accessible | The instance ID. |
| INT mstpPerInstCfgInstancePriority | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1.3 | INTEGER | read-write | A value used to identify the instance root. The instance with the lowest value has the highest priority and is selected as the root. Enter a number 0 through 61440 in steps of 4096. |
| ROW mstpPerInstCfgStatus | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1.4 | RowStatus | read-create | Status of this Instance. |
| mstpPerInstCfgTable | 1.3.6.1.4.1.2882.2.1.1.4.7.3 | not-accessible | Table of descriptive information and configuration about STP on each port. | |
| STR mstpPerInstCfgVlanGroup | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1.2 | DisplayString | read-write | VLAN group of instance. |
| INT mstpPerPortCfgEdgePort | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.7 | INTEGER | read-write | Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages. |
| mstpPerPortCfgEntry | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1 | not-accessible | Information configuring MSTP on a port. | |
| I32 mstpPerPortCfgIndex | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.1 | Integer32 | not-accessible | The index of MstpPerPortCfgEntry. |
| I32 mstpPerPortCfgInstanceID | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.2 | Integer32 | read-only | The instance ID. |
| INT mstpPerPortCfgLinkType | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.6 | INTEGER | read-write | Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively. |
| I32 mstpPerPortCfgPathCost | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.4 | Integer32 | read-write | The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000. (0 will auto set path cost to standard recommended value) |
| I32 mstpPerPortCfgPortNum | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.3 | Integer32 | read-only | The port number. |
| INT mstpPerPortCfgPriority | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.5 | INTEGER | read-write | Decide which port should be blocked by priority in LAN. Enter a number from 0 through 240 in steps of 16. |
| mstpPerPortCfgTable | 1.3.6.1.4.1.2882.2.1.1.4.7.4 | not-accessible | Table of descriptive information and configuration about MSTP on each port. | |
| INT mstpPerPortInfoEdgePort | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.9 | INTEGER | read-only | Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages. |
| mstpPerPortInfoEntry | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1 | not-accessible | An entry in the table, containing information about MSTP (Per port). | |
| I32 mstpPerPortInfoIndex | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.1 | Integer32 | not-accessible | The index of MstpPerPortInfoEntry. |
| I32 mstpPerPortInfoInstanceID | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.2 | Integer32 | read-only | The instance ID. |
| INT mstpPerPortInfoLinkType | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.8 | INTEGER | read-only | Some of the rapid state transactions that are possible within MSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively. |
| I32 mstpPerPortInfoPathCost | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.6 | Integer32 | read-only | The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000. |
| I32 mstpPerPortInfoPortNum | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.3 | Integer32 | read-only | Port number. |
| I32 mstpPerPortInfoPriority | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.7 | Integer32 | read-only | Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 in steps of 16. |
| INT mstpPerPortInfoRole | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.4 | INTEGER | read-only | Descriptive information about MSTP switch port roles: disabled(1) MSTP is disabled on this port. root(2) A forwarding port that has been elected for the spanning-tree topology. designated(3) A forwarding port for every LAN segment. alternate(4) An alternate path to the root bridge. This path is different than using the root port. backup(5) A backup/redundant path to a segment where another switch port already connects. |
| INT mstpPerPortInfoState | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.5 | INTEGER | read-only | |
| mstpPerPortInfoTable | 1.3.6.1.4.1.2882.2.1.1.4.8.2 | not-accessible | Table of descriptive information and configuration about rapid spanning tree (Per port). | |
| STR mstpRegionName | 1.3.6.1.4.1.2882.2.1.1.4.7.1 | DisplayString | read-write | MSTP region name. |
| I32 mstpRegionRevision | 1.3.6.1.4.1.2882.2.1.1.4.7.2 | Integer32 | read-write | MSTP region revision. |
| mstpRootInformationEntry | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1 | not-accessible | An entry in the table, containing information about root bridge information of the MSTP. | |
| I32 mstpRootInformationForwardDelay | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.8 | Integer32 | read-only | Forward Delay Time. |
| I32 mstpRootInformationHelloTime | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.7 | Integer32 | read-only | Hello Time. |
| I32 mstpRootInformationInstanceID | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.1 | Integer32 | read-only | The instance ID. |
| I32 mstpRootInformationMaxAge | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.6 | Integer32 | read-only | Max Age. |
| STR mstpRootInformationRootAddress | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.2 | DisplayString | read-only | Root Address. |
| I32 mstpRootInformationRootPathCost | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.5 | Integer32 | read-only | Root Path Cost. |
| STR mstpRootInformationRootPort | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.4 | DisplayString | read-only | Root Port. |
| I32 mstpRootInformationRootPriority | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.3 | Integer32 | read-only | Root Priority. |
| mstpRootInformationTable | 1.3.6.1.4.1.2882.2.1.1.4.8.1 | not-accessible | Table of descriptive information about root bridge of rapid spanning tree in this system. | |
| multicastFiltering | 1.3.6.1.4.1.2882.2.1.1.7 | |||
| networkRedundancy | 1.3.6.1.4.1.2882.2.1.1.4 | |||
| ntpEntry | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3.1.1 | not-accessible | Information configuring IP addresses of NTP servers. | |
| I32 ntpIndex | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3.1.1.1 | Integer32 | not-accessible | This object identifies the entry. |
| IP ntpServerIP | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3.1.1.2 | IpAddress | read-write | The IP address of an NTP Server. Set 0.0.0.0 or 255.255.255.255 to remove this config. |
| ntpTable | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3.1 | not-accessible | Table of descriptive information and configuration about NTP servers. NTP (Network Time Protocol) synchronizes timekeeping among a set of distributed time servers and clients. This synchronization allows events to be correlated when system logs are created and other time-specific events occur. An NTP server is configured to synchronize NTP clients. Servers can be configured to synchronize any client or only specific clients. NTP servers, however, will accept no synchronization information from their clients and therefore will not let clients update or affect the server's time settings. This switch acts as an NTP client, which tries to let its clock be set and synchronized by an external NTP timeserver. It can be configured to use multiple servers (upto 4 servers). | |
| IP pingFailureIP | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.8 | IpAddress | read-write | The fault relay will be trigger if fail to ping the assigned IP address. |
| INT pingHoldTime | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.10 | INTEGER | read-write | Reset the ping process after pingResetTime, and then wait pingHoldTime to ping again. (optional) |
| INT pingResetTime | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.9 | INTEGER | read-write | Reset the ping process after pingResetTime, and then wait pingHoldTime to ping again. (optional) |
| portConfiguration | 1.3.6.1.4.1.2882.2.1.1.3 | |||
| portControl | 1.3.6.1.4.1.2882.2.1.1.3.1 | |||
| portCtrlEntry | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1 | not-accessible | An entry containing information and configuration for a port. | |
| INT portCtrlFlowControl | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.5 | INTEGER | read-write | Flow control configuration. Flow control is used to throttle the throughput rate of an end station to avoid dropping packets during network congestion. If flow control mode is not set and if there is no packet buffer space available, the incoming packets are discarded. Symmetric Flow Control stops and restarts packet transmission by transmitting and receiving pause frames. When a port's free buffer space is almost empty, the device send out a Pause frame to stop the remove node from sending more frames into the switch. When congestion on the port is relieved, the device send out a Pause frame with pause time equal to zero, making the remove node resume transmission. |
| INT portCtrlIndex | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.1 | INTEGER | not-accessible | Index of the port control entry. |
| STR portCtrlPortDescription | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.6 | DisplayString | read-write | The description of port. |
| STR portCtrlPortName | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.2 | DisplayString | read-only | The name of port. |
| INT portCtrlPortStatus | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.3 | INTEGER | read-write | To enable or disable of this port. |
| INT portCtrlSpeedAndDuplex | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.4 | INTEGER | read-write | Speed and duplex configuraion. Different speed and duplex modes are available. There are speeds: 1000 megabits per second (Gigabit Ethernet), 100 megabits per second (Fast Ethernet), and 10 megabits per second (Legacy Ethernet). Full-duplex allows packets to be transmitted in both directions at the same time, while half-duplex allows a device to either transmit or receive, but not both at the same time. Full-duplex may have double bandwidth than half-duplex. You can configure manually from the possible options, listed from best to worst: 1Gb full-duplex(6) 100Mb full-duplex(5) 100Mb half-duplex(4) 10Mb full-duplex(3) 10Mb half-duplex(2) Set to autoNegotiation(1) to allow the two interfaces on the link to exchange the capabilities and characteristics of the each side, and select the best operating mode automatically when a cable is plugged in. |
| portCtrlTable | 1.3.6.1.4.1.2882.2.1.1.3.1.1 | not-accessible | Table of information and configuration for each ports. | |
| portEventEntry | 1.3.6.1.4.1.2882.2.1.1.10.2.1.2.1 | not-accessible | An entry controlling the type of port events. | |
| portEventTable | 1.3.6.1.4.1.2882.2.1.1.10.2.1.2 | not-accessible | Table of descriptive information and controls the reactions to port link up, link down, or both link up and down. Three types of reactions will be triggered: (1)logging in the switch or send logs to remote syslog servers, (2)sending an email, or (3)send an snmp trap. Each type of alert is configured in sysLogConfiguration, smtpConfiguration, snmpTrapServerEnable and snmpTrapServerTable. | |
| I32 portMirrorDestinationPortRX | 1.3.6.1.4.1.2882.2.1.1.11.3.3 | Integer32 | read-write | The RX destination port (sniffer port). Destination port can be used to see all monitor port traffic. You can connect sniffer port to a LAN analysier or netxray. Set to 0 to clear the configuration. A destination port can not be the same as a source port. This object can not be modified if portMirrorStatus is disable. |
| I32 portMirrorDestinationPortTX | 1.3.6.1.4.1.2882.2.1.1.11.3.2 | Integer32 | read-write | The TX destination port (sniffer port). Destination port can be used to see all monitor port traffic. You can connect sniffer port to a LAN analysier or netxray. Set to 0 to clear the configuration. A destination port can not be the same as a source port. This object can not be modified if portMirrorStatus is disable. |
| portmirroring | 1.3.6.1.4.1.2882.2.1.1.11.3 | |||
| I32 portMirrorPortNum | 1.3.6.1.4.1.2882.2.1.1.11.3.4.1.1 | Integer32 | read-only | The Port number. |
| portMirrorSourceEntry | 1.3.6.1.4.1.2882.2.1.1.11.3.4.1 | not-accessible | Information configuring port mirroring on each port. | |
| INT portMirrorSourcePort | 1.3.6.1.4.1.2882.2.1.1.11.3.4.1.2 | INTEGER | read-write | The mode of source port (monitor port). (1) TX only. (2) RX only. (3) RX and TX. (4) Source port is disabled. The ports you want to monitor. All source port traffic will be copied to destination port (sniffer port). This object can not be modified if portMirrorStatus is disable. |
| portMirrorSourceTable | 1.3.6.1.4.1.2882.2.1.1.11.3.4 | not-accessible | Table of descriptive information and configuration of port mirroring in this system. Use this table to select monitor port for this switch. | |
| INT portMirrorStatus | 1.3.6.1.4.1.2882.2.1.1.11.3.1 | INTEGER | read-write | To enable or disable port mirroring. Port mirroring is used to send a copy of inbound or outbound network packets seen on one port to another switch port. Administrators may utilized this mechanism to monitor network traffic as well as the performance of a switch. |
| portSecurity | 1.3.6.1.4.1.2882.2.1.1.9.1 | |||
| MAC portSecurityMac | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.4 | MacAddress | read-write | MAC address of the entry. |
| portSecurityMacEntry | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1 | not-accessible | An entry configuring a static unicast MAC addresses on a port. | |
| I32 portSecurityMacIndex | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.1 | Integer32 | not-accessible | Index of MAC. |
| ROW portSecurityMacStatus | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.5 | RowStatus | read-create | The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory. |
| portSecurityMacTable | 1.3.6.1.4.1.2882.2.1.1.9.1.2 | not-accessible | Table configuring static unicast MAC address for each port. When you add a static MAC address, it remains in the switch's address table, regardless of whether the device is physically connected to the switch. With enabling port security in portSecurityStatusTable, only those MAC addresses configured in portSecurityMacTable are allowed to access the switch or transmit/receive through the port. | |
| I32 portSecurityPort | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.2 | Integer32 | read-write | The port id. |
| I32 portSecurityPortIndex | 1.3.6.1.4.1.2882.2.1.1.9.1.1.1.1 | Integer32 | not-accessible | The port id. |
| INT portSecurityPortStatus | 1.3.6.1.4.1.2882.2.1.1.9.1.1.1.2 | INTEGER | read-write | (1)enable port security on this port. (2)disable port security on this port. |
| portSecurityStatusEntry | 1.3.6.1.4.1.2882.2.1.1.9.1.1.1 | not-accessible | An entry configuring port security for a port. | |
| portSecurityStatusTable | 1.3.6.1.4.1.2882.2.1.1.9.1.1 | not-accessible | A table containing information about port security status on each port. Port security prevents a port from address learning. Only those MAC addresses that are configured by management are allowed to access the switch or transmit/receive through the port. Upto 10 MAC addresses can assigned to each port by adding address entries to portSecurityMacTable or macAddrTable. If the port security functionality is enabled but without any MAC address configured on a port, no traffic can access the switch or transmit/receive from the port. | |
| I32 portSecurityVlanIndex | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.3 | Integer32 | read-write | The vlan id where the MAC address belongs to. |
| STR portSfpDdmRxPowerCurrent | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.9 | DisplayString | read-only | The current SFP Receiveed Power of port. |
| STR portSfpDdmRxPowerRange | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.10 | DisplayString | read-only | The range of SFP Receiveed Power of port. |
| INT portSfpDdmStatus | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.4 | INTEGER | read-write | (1)Enable SFP digital diagnostic and monitoring. (2)Disable SFP digital diagnostic and monitoring. |
| STR portSfpDdmTempatureCurrent | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.5 | DisplayString | read-only | The current SFP Tempature of port. |
| STR portSfpDdmTempatureRange | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.6 | DisplayString | read-only | The range of SFP Tempature of port. |
| STR portSfpDdmTxPowerCurrent | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.7 | DisplayString | read-only | The current SFP Transmitted Power of port. |
| STR portSfpDdmTxPowerRange | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.8 | DisplayString | read-only | The range of SFP Transmitted Power of port. |
| INT portSfpEject | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.2 | INTEGER | read-write | Eject SFP |
| portSfpEntry | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1 | not-accessible | An entry containing SFP information of a port. | |
| I32 portSfpIndex | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.1 | Integer32 | read-only | Index of port SFP table. |
| INT portSfpScan | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.3 | INTEGER | read-write | Scan SFP |
| portSfpTable | 1.3.6.1.4.1.2882.2.1.1.3.2.2 | not-accessible | Table of descriptive information about SFP | |
| portStatistic | 1.3.6.1.4.1.2882.2.1.1.11.2 | |||
| portStatus | 1.3.6.1.4.1.2882.2.1.1.3.2 | |||
| portStatusEntry | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1 | not-accessible | An entry containing statistics information of a port. | |
| INT portStatusFlowCtrl | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.6 | INTEGER | read-only | Indicate the flow control status of the port. |
| I32 portStatusIndex | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.1 | Integer32 | read-only | Index of port statistic table. |
| INT portStatusLink | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.3 | INTEGER | read-only | Indicate the link state of the port. |
| INT portStatusSpeedDuplex | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.5 | INTEGER | read-only | Indicate the speed and duplex mode of the port. |
| INT portStatusState | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.4 | INTEGER | read-only | Indicate the state of the port. |
| portStatusTable | 1.3.6.1.4.1.2882.2.1.1.3.2.1 | not-accessible | Table of descriptive and statistics information about each ports. | |
| INT portStatusType | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.2 | INTEGER | read-only | Indicates the type of the port. |
| portTrunk | 1.3.6.1.4.1.2882.2.1.1.3.4 | |||
| INT portTrunkAggregatorGroupId | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1.1.2 | INTEGER | read-write | Trunk group Id. Upto 8 ports can be aggregated into a group and 5 groups can be configured in the device. |
| INT portTrunkAggregatorGroupIndex | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.1 | INTEGER | read-only | The trunk group identifier. |
| POR portTrunkAggregatorGroupMember | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.3 | PortList | read-only | The ports are aggregated with other ports. |
| INT portTrunkAggregatorGroupType | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.2 | INTEGER | read-only | The Aggregator type. (1) The trunk group is LACP disabled and configured staticly by administrator. (2) The trunk group is LACP enabled. |
| POR portTrunkAggregatorIndividual | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.4 | PortList | read-only | A port is LACP enabled but not aggregated with other ports. |
| POR portTrunkAggregatorLinkDown | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.5 | PortList | read-only | The ports which are linked down. |
| INT portTrunkAggregatorSettingApply | 1.3.6.1.4.1.2882.2.1.1.3.4.1.2 | INTEGER | read-write | set active(1) to apply the configuration |
| portTrunkAggregatorSettingEntry | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1.1 | not-accessible | Information controlling aggregator configuration. | |
| portTrunkAggregatorSettingTable | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1 | not-accessible | Table of descriptive information and configuration about of each trunk group in this system. Link aggregation, or IEEE 802.3ad, is a method of combining physical network links into a single logical link for increased bandwidth. With Link aggregation we are able to increase the capacity and availability of the communications channel between devices (both switches and end stations) using existing Fast Ethernet and Gigabit Ethernet technology. Two or more Gigabit Ethernet connections are combined in order to increase the bandwidth capability and to create resilient and redundant links. A set of multiple parallel physical links between two devices is grouped together to form a single logical link. Link Aggregation also provides load balancing where the processing and communications activity is distributed across the links in a trunk so that no single link is overwhelmed. | |
| portTrunkAggregatorStatusEntry | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1 | not-accessible | An entry containing information about current configuration of trunk groups. | |
| portTrunkAggregatorStatusTable | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1 | not-accessible | Table of descriptive information about trunk groups in the device. | |
| INT portTrunkAggregatorType | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1.1.3 | INTEGER | read-write | The Aggregator type. You can assign the aggregator staticly by setting to static(1), or setting to lacp(2) to enable the LACP protocol. The Link Aggregation Control Protocol (LACP) is required for dynamically exchanging configuration information between the peer devices in order to automatically configure and maintain link aggregation groups. The protocol is able to automatically detect the presence and capabilities of other aggregation capable devices, i.e. with LACP it is possible to specify which links in a system can be aggregated. This column has no effect if Group Id is set to none. |
| INT portTrunkPortIndex | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1.1.1 | INTEGER | read-only | The port number. |
| INT powerFailureConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.6 | INTEGER | read-write | The fault relay will be triggered if the configured power fails. Any means either power 1 or power2 fails |
| private | 1.3.6.1.4 | |||
| privateVlan | 1.3.6.1.4.1.2882.2.1.1.5.3 | |||
| privateVlanHostAssociationEntry | 1.3.6.1.4.1.2882.2.1.1.5.3.3.1 | not-accessible | Information controlling Private VLAN host port association configuration on the device. | |
| INT privateVlanHostAssociationPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.3.3.1.1 | INTEGER | not-accessible | The Private Host Port Index. |
| INT privateVlanHostAssociationPrimaryVid | 1.3.6.1.4.1.2882.2.1.1.5.3.3.1.2 | INTEGER | read-write | Private VLAN host Port association primary VLAN ID. If enter 0 then clear setting. |
| INT privateVlanHostAssociationSecondaryVid | 1.3.6.1.4.1.2882.2.1.1.5.3.3.1.3 | INTEGER | read-write | Private VLAN host Port association secondary VLAN ID(isolated/community). If enter 0 then clear setting. |
| privateVlanHostAssociationTable | 1.3.6.1.4.1.2882.2.1.1.5.3.3 | not-accessible | A table containing per Private VLAN host port association information in the device. | |
| INT privateVlanId | 1.3.6.1.4.1.2882.2.1.1.5.3.1.1.1 | INTEGER | not-accessible | The Private VLAN ID. |
| privateVlanIdEntry | 1.3.6.1.4.1.2882.2.1.1.5.3.1.1 | not-accessible | Information controlling Private VLAN ID configuration on the device. | |
| privateVlanIdTable | 1.3.6.1.4.1.2882.2.1.1.5.3.1 | not-accessible | A table containing per Private VLAN ID information in the device. | |
| INT privateVlanIdType | 1.3.6.1.4.1.2882.2.1.1.5.3.1.1.2 | INTEGER | read-write | Private VLAN ID type controls |
| privateVlanMappingEntry | 1.3.6.1.4.1.2882.2.1.1.5.3.4.1 | not-accessible | Information controlling Private VLAN promiscuous port mapping configuration on the device. | |
| INT privateVlanMappingPrimaryVid | 1.3.6.1.4.1.2882.2.1.1.5.3.4.1.2 | INTEGER | read-write | Private VLAN promiscuous Port mapping primary VLAN ID. If enter 0 then clear setting. |
| INT privateVlanMappingPromiscuousPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.3.4.1.1 | INTEGER | not-accessible | The Private Promiscuous Port Index. |
| STR privateVlanMappingSecondaryVidList | 1.3.6.1.4.1.2882.2.1.1.5.3.4.1.3 | DisplayString | read-write | Private VLAN promiscuous Port mapping secondary VLAN ID list. If enter zero-length string then clear setting. |
| privateVlanMappingTable | 1.3.6.1.4.1.2882.2.1.1.5.3.4 | not-accessible | A table containing per Private VLAN promiscuous port mapping information in the device. | |
| privateVlanPortEntry | 1.3.6.1.4.1.2882.2.1.1.5.3.2.1 | not-accessible | Information controlling Private VLAN Port configuration on the device. | |
| INT privateVlanPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.3.2.1.1 | INTEGER | not-accessible | The Private Port Index. |
| INT privateVlanPortMode | 1.3.6.1.4.1.2882.2.1.1.5.3.2.1.2 | INTEGER | read-write | Private VLAN Port mode controls |
| privateVlanPortTable | 1.3.6.1.4.1.2882.2.1.1.5.3.2 | not-accessible | A table containing per Private VLAN Port information in the device. | |
| products | 1.3.6.1.4.1.2882.2 | |||
| INT qosCOS | 1.3.6.1.4.1.2882.2.1.1.6.3.1.2 | INTEGER | read-write | The port priority will follow the COS priority that you have assigned (0)low, (1)middle, (2)high, or (3)highest. |
| qosCOSEntry | 1.3.6.1.4.1.2882.2.1.1.6.3.1 | not-accessible | An entry in the table, containing inforamtion about COS QOS. | |
| I32 qosCOSPriority | 1.3.6.1.4.1.2882.2.1.1.6.3.1.1 | Integer32 | read-only | COS priority. |
| qosCOSTable | 1.3.6.1.4.1.2882.2.1.1.6.3 | not-accessible | Table of descriptive information and configuration about COS QOS. | |
| INT qosDscp | 1.3.6.1.4.1.2882.2.1.1.6.4.1.2 | INTEGER | read-write | The port priority will follow the Dscp priority that you have assigned (0)low (1)middle, (2)high, (3)highest. |
| qosDscpEntry | 1.3.6.1.4.1.2882.2.1.1.6.4.1 | not-accessible | An entry in the table, containing inforamtion about DSCP QOS. | |
| I32 qosDscpPriority | 1.3.6.1.4.1.2882.2.1.1.6.4.1.1 | Integer32 | read-only | Dscp priority. |
| qosDscpTable | 1.3.6.1.4.1.2882.2.1.1.6.4 | not-accessible | Table of descriptive information and configuration about DSCP QOS. | |
| INT qosPolicy | 1.3.6.1.4.1.2882.2.1.1.6.1 | INTEGER | read-write | (1)8,4,2,1 weight round robin scheme: the switch will follow 8:4:2:1 rate to process priority queue from Hi to lowest queue. This approach prevents the lower priotiry packets from being starved out with only a slight delay to the higher priority packets. (2)Use the strict priority scheme: Queue with higher priority will always be process first, while queue with lower priority will only be processed when the higher priority queue is empty. This approach can cause the lower priorities the be startved out preventing them from transmitting any packets, but it ensures that all high priority packets serviced as soon as possible. |
| I32 qosPortDefaultCos | 1.3.6.1.4.1.2882.2.1.1.6.2.1.3 | Integer32 | read-write | The port priority will follow the default port priority |
| qosPortDefaultCosEntry | 1.3.6.1.4.1.2882.2.1.1.6.2.1 | not-accessible | An entry in the table, containing inforamtion about port default cos value. | |
| qosPortDefaultCosTable | 1.3.6.1.4.1.2882.2.1.1.6.2 | not-accessible | Table of descriptive information and configuration about port default cos value. | |
| I32 qosPortNum | 1.3.6.1.4.1.2882.2.1.1.6.2.1.1 | Integer32 | read-only | Port number. |
| INT qosPortTrust | 1.3.6.1.4.1.2882.2.1.1.6.2.1.2 | INTEGER | read-write | Two kinds of priority information are token into consideration when a packet is processed. One is COS, the IEEE 802.3ac tag containing IEEE 802.1p priority information, and the other is DSCP, the IPv4 Type of Service/DiffServ field. (1)COS only: the port priority will only follow the COS priority that you have assigned. (2)DSCP only: the port priority will only follow the DSCP priority that you have assigned. (3)COS first: the port priority will follow the COS priority first, and then other priority rule. (4)DSCP first: the port priority will follow the DSCP priority first, and the other priority rule. |
| I32 radiusServerAccountingPort | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.4 | Integer32 | read-write | Accounting Port: The UDP port number used by the authentication server to retrieve accounting information. |
| radiusServerEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1 | not-accessible | . | |
| I32 radiusServerIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.1 | Integer32 | not-accessible | Index of Radius server configuration. |
| IP radiusServerIp | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.2 | IpAddress | read-write | IP address of this radius server. |
| I32 radiusServerServerPort | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.3 | Integer32 | read-write | The UDP port number used by the authentication server to authenticate. |
| STR radiusServerSharedKey | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.5 | DisplayString | read-write | A key shared between this switch and authentication server. |
| radiusServerTable | 1.3.6.1.4.1.2882.2.1.1.9.3.3 | not-accessible | . | |
| rateLimiting | 1.3.6.1.4.1.2882.2.1.1.3.3 | |||
| I32 rateLimitingEgressRate | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1.4 | Integer32 | read-write | Egress rate in Mbps, the rate range is from 1 Mbps to 100 Mbps and zero means no limit. Egress rate limiting has effect on all types of packets, including unicast, multicast and broadcast packets. |
| rateLimitingEntry | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1 | not-accessible | An entry containing information and configuration about port rate limiting. | |
| INT rateLimitingIngressLimitType | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1.2 | INTEGER | read-write | The type of ingress packets to be filtered. |
| I32 rateLimitingIngressRate | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1.3 | Integer32 | read-write | Ingress rate in Mbps, the rate range is from 1 Mbps to 100 Mbps and zero means no limit. |
| I32 rateLimitingPortNum | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1.1 | Integer32 | read-only | The port number. |
| rateLimitingTable | 1.3.6.1.4.1.2882.2.1.1.3.3.1 | not-accessible | Table of descriptive information and configuration about port rate limiting. You can set up bandwidth rate and packet limitation type for each ports. Rate limiting is used to control the rate of traffic sent or received on a network interface. For ingress rate limiting, traffic that is less than or equal to the specified rate is received, whereas traffic that exceeds the rate is dropped. For egress rate limiting, traffic that is less than or equal to the specified rate is sent, whereas traffic that exceeds the rate is dropped. | |
| redundantRing | 1.3.6.1.4.1.2882.2.1.1.4.4 | |||
| redundantRingConfigEntry | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1 | not-accessible | An entry containing information about current configuration of rings. | |
| redundantRingConfigTable | 1.3.6.1.4.1.2882.2.1.1.4.4.1 | not-accessible | Table of configuration about redundancy protocol in the device. | |
| redundantRingStatusEntry | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1 | not-accessible | An entry containing information about current status of rings. | |
| redundantRingStatusTable | 1.3.6.1.4.1.2882.2.1.1.4.4.2 | not-accessible | Table of status information about redundancy protocol in the device. | |
| STR restoreAgentBoardFwFileName | 1.3.6.1.4.1.2882.2.1.1.2.6.5 | DisplayString | read-write | The file name to restore from. |
| IP restoreServerIP | 1.3.6.1.4.1.2882.2.1.1.2.6.4 | IpAddress | read-write | The IP address of a TFTP server from which the startup configuration can be downloaded. |
| INT restoreStatus | 1.3.6.1.4.1.2882.2.1.1.2.6.6 | INTEGER | read-write | Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read. |
| save | 1.3.6.1.4.1.2882.2.1.1.12 | |||
| INT saveCfgMgtAction | 1.3.6.1.4.1.2882.2.1.1.12.1 | INTEGER | read-write | Setting this object to active(1) saves current configuration. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read. |
| security | 1.3.6.1.4.1.2882.2.1.1.9 | |||
| I32 sfpDistance | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.9 | Integer32 | read-only | The maximum transimission distance in meters of the Small Form Pluggable (SFP) optical transceiver module. |
| STR sfpVender | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.7 | DisplayString | read-only | The vender name of the Small Form Pluggable (SFP) optical transceiver module. |
| I32 sfpWavelength | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.8 | Integer32 | read-only | The wave length in nanometers (nm) of the Small Form Pluggable (SFP) optical transceiver module. |
| smtpConfiguration | 1.3.6.1.4.1.2882.2.1.1.10.2.3 | |||
| snmp | 1.3.6.1.4.1.2882.2.1.1.8 | |||
| snmpCommunityStringEntry | 1.3.6.1.4.1.2882.2.1.1.8.1.1 | not-accessible | Inforamtion configuring an community string. | |
| I32 snmpCommunityStringIndex | 1.3.6.1.4.1.2882.2.1.1.8.1.1.1 | Integer32 | not-accessible | Index of community string. |
| STR snmpCommunityStringName | 1.3.6.1.4.1.2882.2.1.1.8.1.1.2 | DisplayString | read-write | A community string with maximum 32 characters. |
| INT snmpCommunityStringPrivilege | 1.3.6.1.4.1.2882.2.1.1.8.1.1.3 | INTEGER | read-write | The access privilege of the community string. |
| ROW snmpCommunityStringStatus | 1.3.6.1.4.1.2882.2.1.1.8.1.1.4 | RowStatus | read-create | The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the switch. An entry can be removed by setting to (6)destory. |
| snmpCommunityStringTable | 1.3.6.1.4.1.2882.2.1.1.8.1 | not-accessible | Table of information configuring community strings of SNMP agent. An SNMP community string is a text string that acts as a password. It is used to authenticate messages that are sent between the management station (the SNMP manager) and the device (the SNMP agent). The community string is included in every packet that is transmitted between the SNMP manager and the SNMP agent. After receiving an SNMP request, the SNMP agent compares the community string in the request to the community strings that are configured for the agent. The requests are valid under these circumstances: - Only SNMP Get and Get-next requests are valid if the community string in the request matches the read-only community. - SNMP Get, Get-next, and Set requests are valid if the community string in the request matches the agent's read-write community. By default, 'public' is the read-only community and 'private' is the read-write community. Total 4 community strings are allowed to configure in the device. | |
| INT snmpTrapServerEnable | 1.3.6.1.4.1.2882.2.1.1.8.3 | INTEGER | read-write | To enable, disable snmp trap functionality. SNMPv1 traps are defined in RFC 1157, and SNMPv2c trap is defined as NOTIFICATION. SNMP traps enable this device to notify the management station of significant events by way of an unsolicited SNMP message. After the manager receives the event, the manager displays it and can choose to take an action based on the event. For instance, the manager can poll the agent directly, or poll other associated device agents to get a better understanding of the event. |
| snmpTrapServerEntry | 1.3.6.1.4.1.2882.2.1.1.8.4.1 | not-accessible | An entry in the table, containing inforamtion about a trap server of SNMP agent. | |
| I32 snmpTrapServerIndex | 1.3.6.1.4.1.2882.2.1.1.8.4.1.1 | Integer32 | not-accessible | Index of trap server. |
| IP snmpTrapServerIPAddr | 1.3.6.1.4.1.2882.2.1.1.8.4.1.2 | IpAddress | read-write | Trap Server IP Address. |
| ROW snmpTrapServerStatus | 1.3.6.1.4.1.2882.2.1.1.8.4.1.5 | RowStatus | read-create | The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory. |
| snmpTrapServerTable | 1.3.6.1.4.1.2882.2.1.1.8.4 | not-accessible | Table of descriptive and information about trap servers. A trap server is the recipient of an SNMP trap. The device does not send a trap unless it knows to which station it should send a trap. | |
| STR snmpTrapServerTrapComm | 1.3.6.1.4.1.2882.2.1.1.8.4.1.3 | DisplayString | read-write | The community string of trap server. The password-like string will be sent with the notification operation. |
| INT snmpTrapServerTrapVer | 1.3.6.1.4.1.2882.2.1.1.8.4.1.4 | INTEGER | read-write | The trap version. |
| STR snmpV3UserAuthPassword | 1.3.6.1.4.1.2882.2.1.1.8.2.1.5 | DisplayString | read-write | |
| INT snmpV3UserAuthProtocol | 1.3.6.1.4.1.2882.2.1.1.8.2.1.4 | INTEGER | read-write | MD5(Message Digest 5) or SHA (Secure Hash Algorithm) |
| STR snmpV3UserDesPassword | 1.3.6.1.4.1.2882.2.1.1.8.2.1.6 | DisplayString | read-write | |
| snmpV3UserEntry | 1.3.6.1.4.1.2882.2.1.1.8.2.1 | not-accessible | An entry in the table, containing inforamtion about a trap server of SNMP agent. | |
| I32 snmpV3UserIndex | 1.3.6.1.4.1.2882.2.1.1.8.2.1.1 | Integer32 | not-accessible | Index of snmp v3 user. |
| STR snmpV3UserName | 1.3.6.1.4.1.2882.2.1.1.8.2.1.2 | DisplayString | read-write | |
| INT snmpV3UserSecurityLevel | 1.3.6.1.4.1.2882.2.1.1.8.2.1.3 | INTEGER | read-write | Specifiy the authentication and privacy level - noauth(1) no authentication and no privacy. - auth(2) enables MD5 or SHA packet authentication. - priv(3) enables MD5 or SHA packet authentication and DES packet encryption. |
| ROW snmpV3UserStatus | 1.3.6.1.4.1.2882.2.1.1.8.2.1.7 | RowStatus | read-create | |
| snmpV3UserTable | 1.3.6.1.4.1.2882.2.1.1.8.2 | not-accessible | Table of descriptive and information about trap servers. A trap server is the recipient of an SNMP trap. The device does not send a trap unless it knows to which station it should send a trap. | |
| stp | 1.3.6.1.4.1.2882.2.1.1.4.5 | |||
| STR stpBridgeAddress | 1.3.6.1.4.1.2882.2.1.1.4.5.2 | DisplayString | read-only | Bridge Address. |
| stpBridgeInformation | 1.3.6.1.4.1.2882.2.1.1.4.6 | |||
| INT stpBridgePriority | 1.3.6.1.4.1.2882.2.1.1.4.5.3 | INTEGER | read-write | A value used to identify the root bridge. The bridge with the lowest value has the highest priority and is selected as the root. Enter a number 0 through 61440 in steps of 4096. If you change the value, you must restart RSTP. This item can't be modified, if stpStatus was disabled. |
| I32 stpForwardDelayTime | 1.3.6.1.4.1.2882.2.1.1.4.5.6 | Integer32 | read-write | The number of seconds a port waits before changing from its Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a number 4 through 30. Note:2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if stpStatus was disabled. |
| I32 stpHelloTime | 1.3.6.1.4.1.2882.2.1.1.4.5.5 | Integer32 | read-write | The number of seconds between the transmission of Spanning-Tree Protocol configuration messages. Enter a number 1 through 10 Note: 2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if stpStatus was disabled. |
| I32 stpMaxAge | 1.3.6.1.4.1.2882.2.1.1.4.5.4 | Integer32 | read-write | The number of seconds a bridge waits without receiving Spanning-Tree Protocol configuration messages before attempting a reconfiguration. Enter a number 6 through 40. Note: 2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if stpStatus was disabled. |
| INT stpModeStatus | 1.3.6.1.4.1.2882.2.1.1.4.5.1 | INTEGER | read-write | Enable Spanning Tree protocol, Rapid Spanning Tree protocol, or disable . Rapid Spanning Tree Algorithm and Protocol (RSTP) provides a loop free topology for any LAN or bridged network. RSTP is an evolution of the Spanning Tree Protocol (STP), and was introduced in the extension IEEE 802.1w, and provides for faster spanning tree convergence after a topology change. |
| INT stpPerPortCfgEdgePort | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.6 | INTEGER | read-write | Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages. |
| stpPerPortCfgEntry | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1 | not-accessible | Information configuring STP on a port. | |
| INT stpPerPortCfgLinkType | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.5 | INTEGER | read-write | Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively. |
| I32 stpPerPortCfgPathCost | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.3 | Integer32 | read-write | The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000. (0 will auto set path cost to standard recommended value) |
| I32 stpPerPortCfgPortNum | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.1 | Integer32 | not-accessible | The port number. |
| INT stpPerPortCfgPriority | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.4 | INTEGER | read-write | Decide which port should be blocked by priority in LAN. Enter a number from 0 through 240 in steps of 16. |
| INT stpPerPortCfgStpState | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.2 | INTEGER | read-write | Enable/Disable STP/RSTP/MSTP at this port. Disable STP state when connecting a device in order to avoid STP waiting periods. |
| stpPerPortCfgTable | 1.3.6.1.4.1.2882.2.1.1.4.5.7 | not-accessible | Table of descriptive information and configuration about STP on each port. | |
| INT stpPerPortInfoEdgePort | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.7 | INTEGER | read-only | Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages. |
| stpPerPortInfoEntry | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1 | not-accessible | An entry in the table, containing inforamtion about STP (Per port). | |
| INT stpPerPortInfoLinkType | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.6 | INTEGER | read-only | Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively. STP does not support this function. |
| I32 stpPerPortInfoPathCost | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.4 | Integer32 | read-only | The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000. |
| I32 stpPerPortInfoPortNum | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.1 | Integer32 | not-accessible | Port number. |
| I32 stpPerPortInfoPriority | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.5 | Integer32 | read-only | Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 in steps of 16. |
| INT stpPerPortInfoRole | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.2 | INTEGER | read-only | Descriptive information about RSTP switch port roles: root(1) A forwarding port that has been elected for the spanning-tree topology. alternate(2) An alternate path to the root bridge. This path is different than using the root port. designated(3) A forwarding port for every LAN segment. backup(4) A backup/redundant path to a segment where another switch port already connects. disabled(5) RSTP is disabled on this port. |
| INT stpPerPortInfoState | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.3 | INTEGER | read-only | |
| stpPerPortInfoTable | 1.3.6.1.4.1.2882.2.1.1.4.6.2 | not-accessible | Table of descriptive information and configuration about rapid spanning tree (Per port). | |
| stpRootInformationEntry | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1 | not-accessible | An entry in the table, containing information about root bridge information of the STP. | |
| I32 stpRootInformationForwardDelay | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.8 | Integer32 | read-only | Forward Delay Time. |
| I32 stpRootInformationHelloTime | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.7 | Integer32 | read-only | Hello Time. |
| I32 stpRootInformationIndex | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.1 | Integer32 | not-accessible | Index of root bridge information table. |
| I32 stpRootInformationMaxAge | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.6 | Integer32 | read-only | Max Age. |
| STR stpRootInformationRootAddress | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.2 | DisplayString | read-only | Root Address. |
| I32 stpRootInformationRootPathCost | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.5 | Integer32 | read-only | Root Path Cost. |
| STR stpRootInformationRootPort | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.4 | DisplayString | read-only | Root Port. |
| I32 stpRootInformationRootPriority | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.3 | Integer32 | read-only | Root Priority. |
| stpRootInformationTable | 1.3.6.1.4.1.2882.2.1.1.4.6.1 | not-accessible | Table of descriptive information about root bridge of rapid spanning tree in this system. | |
| POR superRingBlockedPort | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.8 | PortList | read-only | The blocked ports in ring Normal state. |
| INT superRingConfigId | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.1 | INTEGER | not-accessible | Ring Id. |
| INT superRingConfigVersion | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.3 | INTEGER | read-write | Super Ring funtion version selection. Super Ring: Backward compatible with legacy super ring mechanism. Note: This model supports v1 non-Redundancy Management mode only. Rapid Super Ring: New mechanism. The recovery time is less than 30ms. Any Ring: |
| INT superRingDevicePriority | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.4 | INTEGER | read-write | Super Ring device priority setting. |
| INT superRingDeviceRole | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.3 | INTEGER | read-only | Super Ring role status. (1) disabled. (2) Redundancy manager. (3) Non redundancy manager. |
| STR superRingName | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.2 | DisplayString | read-write | Super Ring name. |
| INT superRingRapidDualHomingStatus | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.9 | INTEGER | read-write | Rapid Dual Homing funtion status. Rapid Dual Homing is a redundancy protocol, which is compatible with RSTP. (1) Rapid Dual Homing function is enabled. (2) Rapid Dual Homing function is disabled. |
| INT superRingRingPort1 | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.5 | INTEGER | read-write | RingPort1 should not equal to RingRort2. |
| INT superRingRingPort1PathCost | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.7 | INTEGER | read-write | |
| INT superRingRingPort2 | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.6 | INTEGER | read-write | RingPort2 should not equal to RingRort1. |
| INT superRingRingPort2PathCost | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.8 | INTEGER | read-write | |
| POR superRingRingPortList1 | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.4 | PortList | read-only | Port list for ring port1. |
| POR superRingRingPortList2 | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.5 | PortList | read-only | Port list for ring port2. |
| I32 superRingRingStateTransitionCount | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.10 | Integer32 | read-only | |
| INT superRingRingStatus | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.6 | INTEGER | read-only | Super Ring ring status. (1) Disabled - The ring on this device is disabled. (1) Normal - Ring is complete. (2) Abnormal - Ring is not complete. |
| MAC superRingRmMac | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.7 | MacAddress | read-only | RM mac address. |
| I32 superRingRoleTransitionCount | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.9 | Integer32 | read-only | |
| ROW superRingStatus | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.10 | RowStatus | read-create | Status of this ring. |
| INT superRingStatusId | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.1 | INTEGER | read-only | Ring Id. |
| INT superRingVersion | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.2 | INTEGER | read-only | Super Ring funtion version selection. Super Ring: Backward compatible with legacy super ring mechanism. Note: This model supports v1 non-Redundancy Management mode only. Rapid Super Ring: New mechanism. The recovery time is less than 30ms. Any Ring: Not Supported: |
| INT switchPortStatClear | 1.3.6.1.4.1.2882.2.1.1.11.2.2 | INTEGER | write-only | Set to clear(1) to clear all information in the statistics table. |
| switchPortStatEntry | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1 | not-accessible | An entry in the table containing descriptive information and statistics of a port. | |
| switchPortStatTable | 1.3.6.1.4.1.2882.2.1.1.11.2.1 | not-accessible | Table of descriptive and statistics information about each switch ports. | |
| switchSetting | 1.3.6.1.4.1.2882.2.1.1.2.1 | |||
| STR switchSettingSystemContact | 1.3.6.1.4.1.2882.2.1.1.2.1.3 | DisplayString | read-write | The textual identification of the contact person for this managed node, together with information on how to contact this person. |
| STR switchSettingSystemLocation | 1.3.6.1.4.1.2882.2.1.1.2.1.2 | DisplayString | read-write | The physical location of this node (e.g., telephone closet, 3rd floor'). |
| STR switchSettingSystemName | 1.3.6.1.4.1.2882.2.1.1.2.1.1 | DisplayString | read-write | An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name. |
| I32 swPortStatIndex | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.1 | Integer32 | not-accessible | Index of port statistic table. |
| INT swPortStatLink | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.3 | INTEGER | read-only | Indicates the link state. |
| I32 swPortStatPacketCollision | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.10 | Integer32 | read-only | The count of collision. |
| I32 swPortStatRXAbortPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.7 | Integer32 | read-only | The count of abort frames when receive, which is the total number of discarded and filtered frames. |
| I32 swPortStatRXBadPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.6 | Integer32 | read-only | The count of bad frames received, which is the total number of undersize, fragment, oversize, jabber, RXErr and FCSErr frames. |
| I32 swPortStatRXGoodPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.5 | Integer32 | read-only | The count of good frames received, which is the total number of recieved unicast, broadcast, multicast and pause frames. |
| INT swPortStatState | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.4 | INTEGER | read-only | Indicates the port state. |
| I32 swPortStatTXBadPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.9 | Integer32 | read-only | The count of FCSErr frames when transmit. |
| I32 swPortStatTXGoodPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.8 | Integer32 | read-only | The count of good frames transmitted, which is the total number of transmitted unicast, broadcast, multicast and pause frames. |
| INT swPortStatType | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.2 | INTEGER | read-only | Indicates the port type. |
| sysLogConfiguration | 1.3.6.1.4.1.2882.2.1.1.10.2.2 | |||
| INT sysLogLocalStatus | 1.3.6.1.4.1.2882.2.1.1.10.2.2.1 | INTEGER | read-write | Parameter to configure if the log should to be kept in the device or not. |
| INT sysLogRemoteStatus | 1.3.6.1.4.1.2882.2.1.1.10.2.2.2 | INTEGER | read-write | Parameter to configure the log should be sent to a syslog server specified in sysLogServerAddr or not. When disabled or sysLogServerAddr is 0, the device will not send out or record any log. |
| IP sysLogServerAddr | 1.3.6.1.4.1.2882.2.1.1.10.2.2.3 | IpAddress | read-write | The IP address of syslog server. |
| STR systemContact | 1.3.6.1.4.1.2882.2.1.1.1.3 | DisplayString | read-only | The textual identification of the contact person for this managed node, together with information on how to contact this person. |
| STR systemDescr | 1.3.6.1.4.1.2882.2.1.1.1.4 | DisplayString | read-only | A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters. |
| systemEventEntry | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1 | read-only | An entry containing type of system events. | |
| systemEventTable | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1 | not-accessible | Table of descriptive information and controls the reactions to system events. Three types of reactions will be triggered: (1)logging in the switch or send logs to remote syslog servers, (2)sending an email, or (3)send an snmp trap. Each type of alert is configured in sysLogConfiguration, smtpConfiguration, snmpTrapServerEnable and snmpTrapServerTable. | |
| STR systemFwVer | 1.3.6.1.4.1.2882.2.1.1.1.5 | DisplayString | read-only | Firmware version of the device. |
| systemInfo | 1.3.6.1.4.1.2882.2.1.1.1 | |||
| STR systemLocation | 1.3.6.1.4.1.2882.2.1.1.1.2 | DisplayString | read-only | The physical location of this node (e.g., telephone closet, 3rd floor'). |
| MAC systemMacAddress | 1.3.6.1.4.1.2882.2.1.1.1.6 | MacAddress | read-only | The MAC address of this device. An Media Access Control address (MAC address) is a unique identifier attached to most network adapters (NICs). It is a number that acts like a name for a particular network adapter |
| STR systemName | 1.3.6.1.4.1.2882.2.1.1.1.1 | DisplayString | read-only | An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name. |
| systemReboot | 1.3.6.1.4.1.2882.2.1.1.2.9 | |||
| INT systemRebootActive | 1.3.6.1.4.1.2882.2.1.1.2.9.1 | INTEGER | read-write | Set active(1) to restart the device. Set to notActive(2) has no effect. The device always returns the value notActive(2) when this object is read. |
| STR systemTime | 1.3.6.1.4.1.2882.2.1.1.2.4.1 | DisplayString | read-only | current system time in format yyyy.mm.dd-hh:mm:ss |
| STR tftpDownloadAgentBoardFwFileName | 1.3.6.1.4.1.2882.2.1.1.2.7.2 | DisplayString | read-write | The file name of the firmware to be downloaded. |
| IP tftpDownloadServerIP | 1.3.6.1.4.1.2882.2.1.1.2.7.1 | IpAddress | read-write | The IP address of a TFTP server where a firmware image can be downloaded. |
| INT tftpDownloadStatus | 1.3.6.1.4.1.2882.2.1.1.2.7.3 | INTEGER | read-write | Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read. |
| tftpUpgrade | 1.3.6.1.4.1.2882.2.1.1.2.7 | |||
| timeSetting | 1.3.6.1.4.1.2882.2.1.1.2.4 | |||
| trafficPrioritization | 1.3.6.1.4.1.2882.2.1.1.6 | |||
| unknownMulticast | 1.3.6.1.4.1.2882.2.1.1.7.3 | |||
| INT unknownMulticastStatus | 1.3.6.1.4.1.2882.2.1.1.7.3.1 | INTEGER | read-write | Select IGMP Unknown Multicast policy. (1) Send to Query Ports: The device sends the packets with an unknown MAC/IP Multicast address to query ports (2) Discard: The device discards all packets with an unknown MAC/IP Multicast address. (3) Send to All Ports: The device sends the packets with an unknown MAC/IP Multicast address to all ports. |
| INT utcTimeZone | 1.3.6.1.4.1.2882.2.1.1.2.4.2 | INTEGER | read-write | UTC Timezone list. (GMT-12:00) Eniwetok, Kwajalein (GMT-11:00) Midway Island, Samoa (GMT-10:00) Hawaii (GMT-09:00) Alaska (GMT-08:00) Pacific Time (US & Canada), Tijuana (GMT-07:00) Arizona (GMT-07:00) Mountain Time (US & Canada) (GMT-06:00) Central America (GMT-06:00) Central Time (US & Canada) (GMT-06:00) Mexico City (GMT-06:00) Saskatchewan (GMT-05:00) Bogota, Lima, Quito (GMT-05:00) Eastern Time (US & Canada) (GMT-05:00) Indiana (East) (GMT-04:00) Atlantic Time (Canada) (GMT-04:00) Caracas, La Paz (GMT-04:00) Santiago (GMT-03:00) NewFoundland (GMT-03:00) Brasilia (GMT-03:00) Buenos Aires, Georgetown (GMT-03:00) Greenland (GMT-02:00) Mid-Atlantic (GMT-01:00) Azores (GMT-01:00) Cape Verde Is. (GMT) Casablanca, Monrovia (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London (GMT+01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna (GMT+01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague (GMT+01:00) Brussels, Copenhagen, Madrid, Paris (GMT+01:00) Sarajevo, Skopje, Sofija, Vilnius, Warsaw, Zagreb (GMT+01:00) West Central Africa (GMT+02:00) Athens, Istanbul, Minsk (GMT+02:00) Bucharest (GMT+02:00) Cairo (GMT+02:00) Harare, Pretoria (GMT+02:00) Helsinki, Riga, Tallinn (GMT+02:00) Jerusalem (GMT+03:00) Baghdad (GMT+03:00) Kuwait, Riyadh (GMT+03:00) Moscow, St. Petersburg, Volgograd (GMT+03:00) Nairobi (GMT+03:30) Tehran (GMT+04:00) Abu Dhabi, Muscat (GMT+04:00) Baku, Tbilisi, Yerevan (GMT+04:30) Kabul (GMT+05:00) Ekaterinburg (GMT+05:00) Islamabad, Karachi, Tashkent (GMT+05:30) Calcutta, Chennai, Mumbai, New Delhi (GMT+05:45) Kathmandu (GMT+06:00) Almaty, Novosibirsk (GMT+06:00) Astana, Dhaka (GMT+06:00) Sri Jayawardenepura (GMT+06:30) Rangoon (GMT+07:00) Bangkok, Hanoi, Jakarta (GMT+07:00) Krasnoyarsk (GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi (GMT+08:00) Irkutsk, Ulaan Bataar (GMT+08:00) Kuala Lumpur, Singapore (GMT+08:00) Perth (GMT+08:00) Taipei (GMT+09:00) Osaka, Sapporo, Tokyo (GMT+09:00) Seoul (GMT+09:00) Yakutsk (GMT+09:30) Adelaide (GMT+09:30) Darwin (GMT+10:00) Brisbane (GMT+10:00) Canberra, Melbourne, Sydney (GMT+10:00) Guam, Port Moresby (GMT+10:00) Hobart (GMT+10:00) Vladivostok (GMT+11:00) Magadan, Solomon Is., New Caledonia (GMT+12:00) Aukland, Wellington (GMT+12:00) Fiji, Kamchatka, Marshall Is. (GMT+13:00) Nuku'alofa |
| vlan | 1.3.6.1.4.1.2882.2.1.1.5 | |||
| INT vlanManagementVlan | 1.3.6.1.4.1.2882.2.1.1.5.1 | INTEGER | read-write | The VLAN from which managemnet traffic can access the device. By default, VLAN 1 is management VLAN. |
| warning | 1.3.6.1.4.1.2882.2.1.1.10 |
RFC description
Vendor-private MIB for Comtrol ES8510 serial device server; manages serial port configuration, status, and connectivity.
Start monitoring Comtrol ES8510 industrial managed Ethernet switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.