CTRON-DECIV-ROUTER-MIB

All MIBs › CTRON-DECIV-ROUTER-MIB

Category: Routing Protocols, SNA and Legacy Protocols, Vendor: Cabletron/Enterasys

Description: Manages Cabletron DECnet IV routing protocol configuration, routing tables, and adjacency status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CTRON-DECIV-ROUTER-MIB?

CTRON-DECIV-ROUTER-MIB is a Cabletron Systems private MIB for managing DECnet Phase IV routing protocol configuration and status on Cabletron routers/multiprotocol switches. It exposes objects covering router identity, node type, adjacency and routing limits (max nodes, max broadcast/level routing area entries, max hops, max cost, max visits), and timer configuration for broadcast and non-broadcast circuits. As a routing-protocol configuration MIB it is used mainly to confirm the software-level DECnet routing setup and scaling limits are correctly applied on a router, rather than to expose hardware sensors, though hitting configured limits (e.g., max nodes or max hops) can reveal a network that has outgrown its configured DECnet routing parameters. It is specific to the legacy DECnet Phase IV protocol and has no dependency on modern IETF routing MIBs like OSPF-MIB or BGP4-MIB. It would be encountered only when managing legacy Cabletron network equipment still running DECnet Phase IV in older DEC-centric network environments, where administrators can download the CTRON-DECIV-ROUTER-MIB file to load into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CTRON-DECIV-ROUTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cabletron router/multiprotocol switch (legacy DECnet Phase IV)

Monitoring Examples

An administrator can check nwDecIVSysRouterId and nwDecIVNodeType to confirm a router's DECnet identity and role (Level 1 or Level 2 router). Reviewing nwDecIVMaxNodes, nwDecIVMaxHops, and nwDecIVMaxCost against actual network size helps determine whether the DECnet area has grown beyond its configured routing limits, which would explain unreachable distant nodes; nwDecIVBroadcastTimer and nwDecIVNonBroadcastTimer settings help diagnose slow adjacency formation on broadcast versus point-to-point circuits.

What Can Be Monitored

DECnet router ID and node type
max nodes/hops/cost routing limits
broadcast and non-broadcast timer settings
adjacency/area configuration limits

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
TimeTicks

From RFC1213-MIB

DisplayString

From ROUTER-OIDS

nwRtrProtoSuites

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
nwDecIVAccessControl	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7
ADR nwDecIVAclDestAddress	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.5	DecIVAddress	read-write	Specifies the destination DECnet Address used to compare for matches on the access control list. Either the Area ID or Node ID of this address may be set to 0, a wildcard value which matches all areas or all nodes.
nwDecIVAclEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1		not-accessible	Each entry contains DECnet source/destination access information.
INT nwDecIVAclIdentifier	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.1	INTEGER	read-only	This is the primary (major) index into the DECnet access control list table. This value identifies each access control list by a unique identifier, a number arbitrarily assigned by the user. All entries that have the same value for nwDecIVAclIdentifier belong to the same access control list.
CTR nwDecIVAclMatches	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.4	Counter	read-only	Indicates the number of matches on this entry that have resulted in the permit/deny access restriction being applied as part of the forwarding process.
INT nwDecIVAclPermission	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.3	INTEGER	read-write	Specifies whether access is allowed or denied between the source and destination address pair. Note that source and destination are interchangeable when bi-directional control is selected. To remove an existing entry set nwDecIVAclPermission to invalid (2). Invalid entries disappear after reboot.
INT nwDecIVAclSequence	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.2	INTEGER	read-only	This is the secondary (minor) index into the DECnet access control list table. This number corresponds to a sequence number used to order multiple entries within the same access control list.
ADR nwDecIVAclSrcAddress	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.6	DecIVAddress	read-write	Specifies the source DECnet Address used to compare for matches on the access control list. Either the Area ID or Node ID of this address may be set to a wildcard value which matches all areas or all nodes.
nwDecIVAclTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2		not-accessible	This table contains the access control list information for DECnet traffic. This table contains entries each of which specifies whether packet forwarding between a particular source destination pair is permitted or denied. Each entry is part of a particular access control list. Each list is identified by a unique Access Control ID. Each list may contain multiple entries ordered by sequence number. When an Access Control List is searched, it is searched in sequence number order and the first match found ends the search. If no match is found, access defaults to permitted.
GAU nwDecIVAclValidEntries	1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.1	Gauge	read-only	Indicates the number of valid entries that exist in the access control list table, nwDecIVAclTable.
INT nwDecIVAreas	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.11	INTEGER	read-write	Specifies the maximum number of areas allowed within a Level 2 (inter-area)routing domain.
TIK nwDecIVBroadcastTimer	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.10	TimeTicks	read-write	Specifies the periodic interval (in seconds) at which DECnet Routing Services advertises its route table on any multi-access broadcast networks attached to any router port configured and enabled for DECnet Phase IV Routing Services.
nwDecIVComponents	1.3.6.1.4.1.52.4.2.2.2.3.3.2
nwDecIVDistanceVector	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1
nwDecIVEndSystems	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6
nwDecIVEvent	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10
INT nwDecIVEventAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.1	INTEGER	read-write	Sets the administrative state of DECnet event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive.
nwDecIVEventEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1		not-accessible	Each entry contains the information about an event that has been logged to the event table.
nwDecIVEventFilterEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1		not-accessible	Each entry describes an event filter which defines a particular type of event to be logged to the event log. The value of nwDecIVEventFltrProtocol indicates the value used either in the nwRtgProtocolTable or the nwComponentTable in the Cabletron Routing Services MIB, which identifies the protocol or component to which the entry applies.
nwDecIVEventFilterTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1		not-accessible	This table contains and entry for each event filter configured for DECnet Phase IV Routing Services events.
INT nwDecIVEventFltrAction	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.6	INTEGER	read-write	Specifies how the events are to be logged. Logging to the `log' stores the events in the event log table (nwDecIVEventLogTable). Logging to'trap' sends events out through the trap mechanism.
INT nwDecIVEventFltrControl	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.3	INTEGER	read-write	Set this value to 3 to add the entry to the event filter table. Set this value to 2 to remove the entry from the event filter table.
INT nwDecIVEventFltrIfNum	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.2	INTEGER	read-only	Specifies the router port involved in the event for which the event filter exists.
INT nwDecIVEventFltrProtocol	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.1	INTEGER	read-only	Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentRtgInstance which identifies the protocol involved in the event for which the event filter exists.
INT nwDecIVEventFltrSeverity	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.5	INTEGER	read-write	Specifies the level of severity an event must meet in order to be logged. Controls the amount of event logging by ignoring events of a lower priority than specified by this filter value. `Highmed' ignores only events of the lowest severity. `Highlow' logs all events highest priority through lowest. `Highest' severity causes all events except those of the highest severity to be ignored. `Highmed' severity is the default setting which causes only events of the lowest severity to be ignored. `Highlow' severity logs all events, regardless of severity.
INT nwDecIVEventFltrType	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.4	INTEGER	read-write	This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events are to be logged. Setting any bit to 0 removes an event type from this field and prevents that type of event from being logged. Setting any bit to 1 adds an event type to this field and enables that type of event to be logged.
INT nwDecIVEventIfNum	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.6	INTEGER	read-only	Indicates the router port that was involved in the event.
nwDecIVEventLogConfig	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1
nwDecIVEventLogFilterTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2
nwDecIVEventLogTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3
INT nwDecIVEventMaxEntries	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.2	INTEGER	read-write	Sets the maximum number of entries allowed in the event log table. When the number of entries reaches the value of nwDecIVEventMaxEntries, the first (oldest) entry is deleted to allow a new entry to be added.
INT nwDecIVEventNumber	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.1	INTEGER	read-only	An ordinal value assigned to the event for which the log entry exists. nwDecIVEventNumber is assigned so that each event in the event log can be uniquely identified by the value of nwDecIVEventNumber.
INT nwDecIVEventProtocol	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.5	INTEGER	read-only	Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentInstance which identifies the protocol or component that was involved in the event.
INT nwDecIVEventSeverity	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.4	INTEGER	read-only	Indicates the severity that was assigned to the event.
nwDecIVEventTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1		not-accessible	This table contains an entry for each event that has been logged.
OCT nwDecIVEventTextString	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.7	OCTET STRING	read-only	Contains the actual text string that was logged.
TIK nwDecIVEventTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.2	TimeTicks	read-only	Indicates the time at which the event was logged to the event log.
INT nwDecIVEventTraceAll	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.3	INTEGER	read-write	Enabled (3) allows logging of all event types on all router ports for all protocols and components. Disabled (2) causes the filter table to specify which events to log.
INT nwDecIVEventType	1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.3	INTEGER	read-only	Indicates the type of event that was logged.
nwDecIVFib	1.3.6.1.4.1.52.4.2.2.2.3.3.2.5
nwDecIVFibEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1		not-accessible	Each entry in the table describes a route to a particular DECnet destination network and node.
INT nwDecIVFibNextHopIf	1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.3	INTEGER	read-write	Indicates the value of MIB 2 ifindex, which identifies the router port through which the route exists.
ADR nwDecIVFibNextHopNodeId	1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.2	DecIVAddress	read-write	Contains the DECnet Address of the next hop router for the route for which the entry exists.
ADR nwDecIVFibNodeId	1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.1	DecIVAddress	read-only	Contains the DECnet Address of the destination node of the route for which the entry exists.
INT nwDecIVFibRouteType	1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.4	INTEGER	read-write	Indicates the status of the route. A value of 3 indicates that the destination is on the network segment that is directly connected to the router port identified by nwDecIVFibNextHopIf. A value of 4 indicates that the destination is on an indirectly connected network segment, which is reachable through the next hop router indicated by the value of nwDecIVFibNextHopNodeId. A value of 2 indicates that the route is invalid.
nwDecIVFibTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1		not-accessible	This table contains an entry for each route being used to forward DECnet data packets..
nwDecIVFilters	1.3.6.1.4.1.52.4.2.2.2.3.3.2.8
nwDecIVForwarding	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2
nwDecIVFwdCounters	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1
CTR nwDecIVFwdCtrAddrErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.9	Counter	read-only	Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because of addressing errors in the DECnet header.
INT nwDecIVFwdCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.1	INTEGER	read-write	Sets the administrative state of the aggregate (system-wide) DECnet packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
CTR nwDecIVFwdCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.16	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been discarded, system wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.8	Counter	read-only	Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.15	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been administratively filtered, system-wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.7	Counter	read-only	Indicates the total number of DECnet packets that have been administratively filtered, system-wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrFwdBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.14	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been forwarded, system-wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrFwdPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.6	Counter	read-only	Indicates the total number of DECnet packets that have been forwarded, system-wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrHdrErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.11	Counter	read-only	Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because of an invalid DECnet header.
CTR nwDecIVFwdCtrHostDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.22	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been discarded by the local host, during nwDecIVFwdCtrOperationalTime, due to a lack of host resources.
CTR nwDecIVFwdCtrHostDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.19	Counter	read-only	Indicates the total number of DECnet packets that have been discarded by the local host, during nwDecIVFwdCtrOperationalTime, due to a lack of host resources.
CTR nwDecIVFwdCtrHostInBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.20	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been received by the local host, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrHostInPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.17	Counter	read-only	Indicates the total number of DECnet packets that have been successfully delivered to the local host, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrHostOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.21	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been transmitted by the local host, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrHostOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.18	Counter	read-only	Indicates the total number of DECnet packets that have been transmitted by the local host, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.12	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been received, system-wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.4	Counter	read-only	Indicates the total number of DECnet packets that have been received, system-wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrLenErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.10	Counter	read-only	Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because an invalid packet length is contained in the DECnet header.
TIK nwDecIVFwdCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.3	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that DecIVFwdCtrOperStatus has been in the current state.
CTR nwDecIVFwdCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.13	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been transmitted, system-wide, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.5	Counter	read-only	Indicates the total number of DECnet packets that have been transmitted, system-wide, during nwDecIVFwdCtrOperationalTime.
INT nwDecIVFwdCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.2	INTEGER	read-write	Resets the aggregate (system-wide) DECnet packet and byte counters. Reset (2) resets the DECnet aggregate counters to 0. nwDecIVFwdCtrOperationalTime is also reset to 0.
INT nwDecIVFwdIfAclIdentifier	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.9	INTEGER	read-write	Specifies the Access Control ID of the access control list in effect for DECnet packets being routed on the router port for which the entry exists. A value of 0 indicates that no access control list is in effect.
INT nwDecIVFwdIfAclStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.10	INTEGER	read-write	Controls the operation of any access control list configured for DECnet traffic on the router port for which the entry exists. Enabled (3) applies the access control list indicated by the value of nwDecIVFwdIfAclIdentifier to all DECnet traffic being routed on the port. Disabled (2) prevents the access control list from being applied.
INT nwDecIVFwdIfAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.2	INTEGER	read-write	Sets the administrative state of DECnet Phase IV Routing Services on the router port for which the entry exists. Enabled (3) causes DECnet Phase IV Routing Services to become active. Disabled (2) causes it to become inactive.
INT nwDecIVFwdIfCacheControl	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.11	INTEGER	read-write	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
CTR nwDecIVFwdIfCacheEntries	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.12	Counter	read-only	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
CTR nwDecIVFwdIfCacheHits	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.13	Counter	read-only	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
CTR nwDecIVFwdIfCacheMisses	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.14	Counter	read-only	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
nwDecIVFwdIfConfig	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1
INT nwDecIVFwdIfControl	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.5	INTEGER	read-write	This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
nwDecIVFwdIfCounters	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2
CTR nwDecIVFwdIfCtrAddrErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.10	Counter	read-only	Indicates the total number of DECnet packets that have been discarded because of addressing errors in the DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
INT nwDecIVFwdIfCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.2	INTEGER	read-write	Sets the administrative state of the per-port DECnet packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
CTR nwDecIVFwdIfCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.17	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been discarded, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.9	Counter	read-only	Indicates the total number of DECnet packets that have been discarded (dropped), during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
nwDecIVFwdIfCtrEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1		not-accessible	Each entry indicates the current packet and byte count of DECnet packets on each router port for which the entry exists.
CTR nwDecIVFwdIfCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.16	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been administratively filtered, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.8	Counter	read-only	Indicates the total number of DECnet packets that have been administratively filtered, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrFwdBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.15	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been forwarded, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrFwdPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.7	Counter	read-only	Indicates the total number of DECnet packets that have been forwarded on the router port for which the entry exists, during nwDecIVFwdCtrOperationalTime.
CTR nwDecIVFwdIfCtrHdrErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.12	Counter	read-only	Indicates the total number of DECnet packets that have been discarded because of an invalid DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrHostDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.23	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been discarded by the local host, due to a lack of host resources, that were received on the router port for which the entry exists, during nwDecIVFwdIfCtrOperationalTime.
CTR nwDecIVFwdIfCtrHostDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.20	Counter	read-only	Indicates the total number of DECnet packets that have been discarded by the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrHostInBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.21	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been delivered to the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrHostInPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.18	Counter	read-only	Indicates the total number of DECnet packets that have been delivered to the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrHostOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.22	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrHostOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.19	Counter	read-only	Indicates the total number of DECnet packets that have been transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
INT nwDecIVFwdIfCtrIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
CTR nwDecIVFwdIfCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.13	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been received, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.5	Counter	read-only	Indicates the total number of DECnet packets that have been received, during nwDecIVFwdIfCtrOperationaltime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrLenErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.11	Counter	read-only	Indicates the total number of DECnet packets that have been discarded because an invalid packet length was contained in the DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
TIK nwDecIVFwdIfCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that the per-port DECnet packet and byte counters have been active on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.14	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVFwdIfCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.6	Counter	read-only	Indicates the total number of DECnet packets that have been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
INT nwDecIVFwdIfCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.3	INTEGER	read-write	Resets the per-port DECnet packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwDecIVFwdIfCtrOperationalTime is also reset to 0.
nwDecIVFwdIfCtrTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1		not-accessible	This table contains an entry for each router port configured and enabled for DECnet Phase IV Routing Services.
nwDecIVFwdIfEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1		not-accessible	Each entry specifies the DECnet Phase IV Routing Services configuration for the router port for which the entry exists.
INT nwDecIVFwdIfForwarding	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.7	INTEGER	read-write	Controls the forwarding of DECnet packets on the router port for which the entry exists. Enabled (3) causes DECnet packets to be forwarded. Disabled (2) prevents DECnet packets from being forwarded.
INT nwDecIVFwdIfFrameType	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.8	INTEGER	read-write	Specifies the framing type for DECnet packets forwarded on the router port for which the entry exists. Some frame types are only valid for specific media types. The comments reflect those valid media types.
INT nwDecIVFwdIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
INT nwDecIVFwdIfMtu	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.6	INTEGER	read-write	Specifies the Maximum Transmission Unit (MTU) for DECnet packets on the router port for which the entry exists. This includes the DECnet header and data, but does not include framing.
TIK nwDecIVFwdIfOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwDecIVFwdIfOperStatus has been in its current state.
INT nwDecIVFwdIfOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.3	INTEGER	read-only	Indicates the current operating condition of DECnet Phase IV Routing Services on the router port for which the entry exists. The value of nwDecIVFwdIfOperStatus indicates any problem with the configuration of DECnet Phase IV Routing Services on the router port. value of 6 indicates that regardless of the value of nwDecIVFwdIfAdminStatus, DECnet Phase IV Routing Services is not operating because of an invalid port-level configuration.
nwDecIVFwdIfTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1		not-accessible	This table contains an entry for each router port. This table is indexed by nwDecIVFwdIfIndex, which indicates the value of MIB 2 ifIndex, which identifies the router port for which each entry exists.
nwDecIVFwdInterfaces	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2
nwDecIVFwdSystem	1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1
INT nwDecIVHostMapCircuitID	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.4	INTEGER	read-write	The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the DecIV Address at the end of the circuit. For non-WAN interfaces, the value of this object is zero.
ADR nwDecIVHostMapDecIVAddr	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.2	DecIVAddress	read-only	The DecIVAddress of the host on the corresponding interface and circuit (if applicable).
nwDecIVHostMapEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1		not-accessible	Each entry contains one DecIVAddress to circuit equivalence. Also provided is the framing required to converse with this host, and the corresponding logical port number.
INT nwDecIVHostMapFraming	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.5	INTEGER	read-write	Specifies the framing type required to converse with the host for which this entry exists.
INT nwDecIVHostMapIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.1	INTEGER	read-only	This is the primary (major) index into the DecIV HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the DecIV router port for which the entry exists.
INT nwDecIVHostMapPortNumber	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.6	INTEGER	read-only	The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of configured interfaces in the system and the number of circuits present on those interfaces which are of WAN type.
nwDecIVHostMapTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1		not-accessible	The DecIV Address translation table used for mapping a DecIV address to a circuit identifier (if applicable), corresponding port number, and framing type.
INT nwDecIVHostMapType	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.3	INTEGER	read-write	Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwDecIVHostMapTable. That is, it effectively dissasociates the circuitand/or interface identified with said entry from the mapping identified with said entry. It is an implementation- specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper inter- pretation of such entries requires examination of the relevant wDecIVHostMapType object.
nwDecIVHostsInterfaces	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.2
nwDecIVHostsSystem	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.1
nwDecIVHostsToMedia	1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3
nwDecIVLinkState	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.2
INT nwDecIVMaxAreaCost	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.13	INTEGER	read-write	Specifies the maximum cost allowed for a valid Level 2 (inter-area) route. Any inter-area route with a cost greater than nwDecIVMaxAreaCost is considered unreachable.
INT nwDecIVMaxAreaHops	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.12	INTEGER	read-write	Specifies the maximum number of areas that can be hopped by a valid inter-area route. Any inter-area route requiring a greater number of areas to be hopped than specified by nwDecIVMaxAreaHops is considered invalid.
INT nwDecIVMaxBEA	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.5	INTEGER	read-write	Specifies the maximum number of endnode adjacencies supported by this node.
INT nwDecIVMaxBRA	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.4	INTEGER	read-write	Specifies the maximum number of router adjacencies supported by this node.
INT nwDecIVMaxCost	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.7	INTEGER	read-write	Specifies the maximum cost allowed for a valid route within the area. Any intra-area route with a cost greater than nwDecIVMaxCost is considered unreachable.
INT nwDecIVMaxHops	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.6	INTEGER	read-write	Specifies the maximum number of hops allowed for a valid route within the area. Any intra-area route consisting of a greater number of hops than specified by nwDecIVMaxHops is considered unreachable.
INT nwDecIVMaxNodes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.3	INTEGER	read-write	Specifies the maximum number of DECnet nodes allowed within an area.
INT nwDecIVMaxVisits	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.8	INTEGER	read-write	Specifies the maximum number of intra-area hops a packet can be forwarded. A packet is dropped once it has been forwarded nwDecIVMaxVisits.
STR nwDecIVMibRevText	1.3.6.1.4.1.52.4.2.2.2.3.3.1.1	DisplayString	read-only	Indicates the current revision level of the DECnet Phase IV MIB in textual format.
nwDecIVMibs	1.3.6.1.4.1.52.4.2.2.2.3.3.1
INT nwDecIVNodeType	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.2	INTEGER	read-write	Specifies the node type. Setting this value to 2, (routing-iv), establishes the Routing Services-enabled device as a DECnet Level 1, intra-area router. Setting this value to 2, establishes the Routing Services-enabled device as a DECnet Phase IV Level 2, or inter-area router.
TIK nwDecIVNonBroadcastTimer	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.9	TimeTicks	read-write	Specifies the periodic interval (in seconds) at which DECnet Routing Services advertises its route table, on any non-broadcast networks attached to any router port configured and enabled for DECnet Phase IV Routing Services.
nwDecIVProto	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1
INT nwDecIVProtoAdminReset	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.3	INTEGER	read-write	Resets the DECnet Phase IV distance-vector-based routing protocol. Reset (2) forces a system-wide restart of the protocol without a graceful shut-down on any active router ports.
INT nwDecIVProtoAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.1	INTEGER	read-write	Sets the administrative state of the DECnet Phase IV distance-vector-based routing protocol system-wide. Enabled (3) causes the routing protocol to become active on all router ports configured and enabled for DECnet Routing Services. Disabled (2) causes the routing protocol to become inactive.
INT nwDecIVProtoAgeOut	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.9	INTEGER	read-write	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
nwDecIVProtoConfig	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1
nwDecIVProtoCounters	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2
INT nwDecIVProtoCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.1	INTEGER	read-write	Sets the administrative state of the aggregate (system-wide) DECnet Phase IV distance-vector-based routing protocol packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
CTR nwDecIVProtoCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.11	Counter	read-only	Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been discarded system-wide, during nwDecIVProtoCtrOperationalTime.
CTR nwDecIVProtoCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.7	Counter	read-only	Indicates the total number of the DECnet Phase IV distance-vector -based routing protocol packets that have been discarded, system-wide, during nwDecIVProtoCtrOperationalTime.
CTR nwDecIVProtoCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.10	Counter	read-only	Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been administratively filtered, system-wide, during nwDecIVProtoCtrOperationalTime.
CTR nwDecIVProtoCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.6	Counter	read-only	Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, system-wide, during nwDecIVProtoCtrOperationalTime.
CTR nwDecIVProtoCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.8	Counter	read-only	Indicates the total number of bytes in the DECnet Phase IV distance-vector based routing protocol packets that have been received, system-wide, during nwDecIVProtoCtrOperationalTime.
CTR nwDecIVProtoCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.4	Counter	read-only	Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been received, system-wide, during nwDecIVProtoCtrOperationalTime.
TIK nwDecIVProtoCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.3	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoCtrAdminStatus has been in it's current state.
CTR nwDecIVProtoCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.9	Counter	read-only	Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been transmitted, system-wide, during nwDecIVProtoCtrOperationalTime.
CTR nwDecIVProtoCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.5	Counter	read-only	Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, system-wide, during nwDecIVProtoCtrOperationalTime.
INT nwDecIVProtoCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.2	INTEGER	read-write	Resets the aggregate (system-wide) DECnet Phase IV distance-vector-based routing protocol packet and byte counters. Reset (2) resets the DECnet aggregate counters to 0. nwDecIVProtoCtrOperationalTime is also reset to 0.
INT nwDecIVProtoDatabaseThreshold	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.8	INTEGER	read-write	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
INT nwDecIVProtoHoldDown	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.10	INTEGER	read-write	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
INT nwDecIVProtoIfAclIdentifier	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.16	INTEGER	read-write	Specifies the Access Control ID of the access control list in effect for DECnet Phase IV distance-vector-based routing protocol packets on the router port for which the entry exists. A value of 0 indicates that there is no access control list in effect for DECnet Phase IV distance-vector-based routing protocol packets on the router port.
INT nwDecIVProtoIfAclStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.17	INTEGER	read-write	Controls the operation of the access control list identified by nwDecIVProtoIfAclIdentifier. Enabled (3) applies the access control list to all DECnet Phase IV distance-vector-based routing protocol packet traffic on the router port for which the entry exists. Disabled (2) prevents the access control list from being applied.
INT nwDecIVProtoIfAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.2	INTEGER	read-write	Sets the administrative state of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. Enabled (3) causes the routing protocol to become active on the router port. Disabled (2) causes it to become inactive.
INT nwDecIVProtoIfAdvertisement	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.6	INTEGER	read-write	Sets the interval, in seconds, at which the DECnet Phase IV distance-vectorbased routing protocol advertises its route table on the router port for which the entry exists. Change this value to cause the DECnet Phase IV distance-vector-based routing protocol to advertise its route table more or less frequently on the router port.
nwDecIVProtoIfConfig	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1
nwDecIVProtoIfCounters	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2
INT nwDecIVProtoIfCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.2	INTEGER	read-write	Sets the administrative state of the per-port DECnet Phase IV distance-vectorbased routing protocol packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
CTR nwDecIVProtoIfCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.12	Counter	read-only	Indicates the total number of bytes in the DECnet packets that have been discarded, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exists.
CTR nwDecIVProtoIfCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.8	Counter	read-only	Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been discarded, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exist.
nwDecIVProtoIfCtrEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1		not-accessible	Each entry indicates the current packet and byte count of DECnet Phase IV distance-vector-based routing protocol packets on the router port for which the entry exists.
CTR nwDecIVProtoIfCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.11	Counter	read-only	Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exists.
CTR nwDecIVProtoIfCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.7	Counter	read-only	Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
INT nwDecIVProtoIfCtrIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
CTR nwDecIVProtoIfCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.9	Counter	read-only	Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been received, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVProtoIfCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.5	Counter	read-only	Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been received, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
TIK nwDecIVProtoIfCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoIfCtrAdminStatus has been in the current state.
CTR nwDecIVProtoIfCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.10	Counter	read-only	Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwDecIVProtoIfCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.6	Counter	read-only	Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
INT nwDecIVProtoIfCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.3	INTEGER	read-write	Resets the per-port DECnet Phase IV distance-vector-based routing protocol packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwDecIVProtoIfCtrOperationalTime is also reset to 0.
nwDecIVProtoIfCtrTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1		not-accessible	This table contains an entry for each router port. This table is indexed by nwDecIVProtoIfCtrIfIndex which indicates the value of MIB2 ifindex, which identifies the router port for which the entry exists.
nwDecIVProtoIfEntry	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1		not-accessible	Each entry contains the DECnet Phase IV distance-vector-based routing protocol configuration for the router port for which the entry exists.
INT nwDecIVProtoIfFloodDelay	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.7	INTEGER	read-write	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
INT nwDecIVProtoIfHelloTimer	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.10	INTEGER	read-write	Sets the interval, in seconds, at which DECnet Phase IV distance-vector-based routing protocol sends Hello packets on the router port for which the entry exists.
INT nwDecIVProtoIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
TIK nwDecIVProtoIfOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoIfOperStatus has been in it`s current state.
INT nwDecIVProtoIfOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.3	INTEGER	read-only	Indicates the current operating condition of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. The value of nwDecIVProtoIfOperStatus indicates any problem with your routing protocol configuration on the router port. A value of 6 indicates that regardless of the value of nwDecIVProtoIfAdminStatus, the routing protocol is not operating because of an invalid configuration.
INT nwDecIVProtoIfPoisonReverse	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.12	INTEGER	read-write	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
INT nwDecIVProtoIfPriority	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.9	INTEGER	read-write	Sets the priority of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. Within an area, the router with the highest value for nwDecIVProtoIfPriority becomes the priority or designated router. The highest possible value for nwDecIVProtocolIfPriority is 127. Set this value high to cause your DECnet Phase IV Routing Services-enabled device to become the designated router. Set this value low to guarantee that it does not become the designated router.
INT nwDecIVProtoIfRequestDelay	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.8	INTEGER	read-write	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
INT nwDecIVProtoIfSnooping	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.13	INTEGER	read-write	Controls the operation of DECnet Phase IV distance-vector-based routing protocol snooping on the router port. When snooping is enabled the DECnet Phase IV distance-vector-based routing protocol operates in passive mode, so that it receives route information, builds and maintains a route table, but does not advertise the route table or send updates on the router port for which the entry exists.
INT nwDecIVProtoIfSplitHorizon	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.11	INTEGER	read-write	This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
nwDecIVProtoIfTable	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1		not-accessible	This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwDecIVProtoIfIndex, which indicates the value of MIB 2 ifIndex, which identifies the router port for which each entry exists.
INT nwDecIVProtoIfType	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.14	INTEGER	read-only	Indicates whether the directly connected network segment does or does not support broadcast media access.
INT nwDecIVProtoIfVersion	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.5	INTEGER	read-write	Indicates the revision level of the DECnet Phase IV distance-vector-based routing protocol firmware on the router port for which the entry exists, in textual format.
INT nwDecIVProtoIfXmitCost	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.15	INTEGER	read-write	Sets the cost of transmitting a packet on the network segment connected to the router port for which the entry exists. The DECnet Phase IV distance-vector-based routing protocol picks the route with the least total nwDecIVProtoIfXmitCost as the best route. If nwDecIVProtocolIfXmitCost, also known as path cost, is the same for all possible routes , the best route chosen is the route with the least number of hops is chosen as the best route.
nwDecIVProtoInterface	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2
TIK nwDecIVProtoOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoOperStatus has been in current state.
INT nwDecIVProtoOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.2	INTEGER	read-only	Indicates the current operating condition of the DECnet Phase IV distance-vector-based routing protocol system-wide. The value of nwDecIVProtoOperStatus indicates any problem with the DECnet Phase IV distance-vector-based routing protocol configuration. A value of 6 indicates that regardless of the value of nwDecIVProtoAdminStatus, the DECnet Phase IV distance-vector-based routing protocol is not operating because of an invalid configuration.
INT nwDecIVProtoStackSize	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.6	INTEGER	read-write	Specifies the stack size of the DECnet Phase IV distance-vector- based routing protocol thread. In order for a change of this value to take effect, the protocol (nwDecIVProtoAdminReset), DECnet Phase IV Routing Services (nwDecIVSysAdminReset), or the device running Routing Services must be reset.
nwDecIVProtoSystem	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1
INT nwDecIVProtoThreadPriority	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.7	INTEGER	read-write	Specifies the run-time execution priority of the DECnet Phase IV distance-vector-based routing protocol thread. In order for a change of this value to take effect, the protocol (nwDecIVProtoAdminReset), DECnet Phase IV Routing Services (nwDecIVSysAdminReset), or the device running Routing Services must be reset.
STR nwDecIVProtoVersion	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.5	DisplayString	read-only	Indicates the current revision level of the DECnet Phase IV distance-vector-based routing protocol firmware, in textual format.
nwDecIVRedirector	1.3.6.1.4.1.52.4.2.2.2.3.3.2.9
nwDecIVRouter	1.3.6.1.4.1.52.4.2.2.2.3.3
nwDecIVSysAdministration	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2
INT nwDecIVSysAdminReset	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.3	INTEGER	read-write	Resets DECnet Phase IV Routing Services, system-wide. Reset (2) forces a restart of DECnet Phase IV Routing Services without a graceful shutdown on any active router ports and without affecting any other routing services.
INT nwDecIVSysAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.1	INTEGER	read-write	Sets the administrative state of DECnet Phase IV Routing Services, system-wide. Enabled (3) causes DECnet Phase IV system-wide Routing Services to become active on all router ports configured and enabled for DECnet Phase IV Routing Services. Disabled (2) causes DECnet Phase IV Routing Services to become inactive system-wide.
nwDecIVSysConfig	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1
TIK nwDecIVSysOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwDecIVSysOperStatus has been in it's current state.
INT nwDecIVSysOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.2	INTEGER	read-only	Indicates the current operating condition of DECnet Phase IV Routing Services system-wide. The value of nwDecIVSysOperStatus indicates any problem with your DECnet Phase IV Routing Services configuration. A value of 6 indicates that regardless of the value of nwDecIVSysAdminStatus, DECnet Phase IV Routing Services is not operating because of an invalid configuration.
ADR nwDecIVSysRouterId	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.1	DecIVAddress	read-write	The DECnet Address used to uniquely identify the host (device) running DECnet Phase IV Routing Services. Since DECnet Phase IV uses a single address to identify the host and all of its router ports, rather than using an address per router port, nwDecIVSysRouterID is the DECnet node address for all the router ports on the device.
nwDecIVSystem	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1
STR nwDecIVSysVersion	1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.5	DisplayString	read-only	Indicates the current revision level of the DECnet Phase IV Routing Services firmware, in textual format.
nwDecIVTopology	1.3.6.1.4.1.52.4.2.2.2.3.3.2.4
nwDecIVWorkGroup	1.3.6.1.4.1.52.4.2.2.2.3.3.2.11

RFC description

Cabletron DECnet Phase IV router MIB defining routing services, forwarding, and network topology management.

Start monitoring Cabletron router/multiprotocol switch (legacy DECnet Phase IV) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CTRON-DECIV-ROUTER-MIB

What Is CTRON-DECIV-ROUTER-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description