CTRON-AP3000-MIB

All MIBs › CTRON-AP3000-MIB

Organization: Enterasys Networks, Inc

Last Updated: 2007-10-30

Category: Vendor: Cabletron/Enterasys, Wireless and WLAN

Description: Manages Cabletron AP3000 wireless access point radio configuration, association tables, and RF statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CTRON-AP3000-MIB?

CTRON-AP3000-MIB is an Enterasys Networks (Cabletron) vendor MIB for the AP3000 wireless access point, providing read-write configuration access to radio, bridging, filtering, and security settings on this early enterprise Wi-Fi access point. It exposes configuration and status objects covering protocol filtering rules (by ISO protocol designator), bridge control over which traffic types (AP management, Ethernet) are subject to filtering, IBSS relay mode settings, and SSH-based security access. Its monitoring value leans toward configuration and access-control status rather than deep radio statistics: enterpriseApFilterProtocolState reveals whether a given protocol filter is active or inactive, apvFilterControlTable tracks which filter policies apply per interface, and apSecuritySsh indicates whether secure management access is enabled, all useful for auditing the AP's security posture and traffic-filtering behavior. It is described as an extension to the base Enterasys AP3000 MIB under the Enterasys enterprise OID, so it depends on and complements that core AP3000 module for full device coverage. It is deployed on Enterasys/Cabletron AP3000 wireless access points in enterprise wireless LAN deployments. Engineers can download the CTRON-AP3000-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CTRON-AP3000-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Enterasys/Cabletron AP3000 wireless access point

Monitoring Examples

An administrator would walk enterpriseApFilterProtocolTable/enterpriseApFilterProtocolEntry to check each enterpriseApFilterProtocolState and confirm expected protocol filters (identified by enterpriseApFilterProtocolISODesignator) are active, and review apvFilterControlTable/apvFilterControlEntry to see which filter policies are bound to the AP's interfaces. Checking apSecuritySsh would confirm whether SSH management access is enabled, an important security posture check for the AP. apvGlobalIBSSRelayMode would be checked when troubleshooting ad-hoc/IBSS client relay behavior on the wireless network.

What Can Be Monitored

protocol filter state
filter policy assignment
IBSS relay mode
SSH management access status

Imported Objects

From RFC1155-SMI

Counter
IpAddress
enterprises
mgmt

From RFC1213-MIB

ifIndex

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks

How to Use in IPNetwork Monitor

Example using apWStationSessionTxPacketCount OID:

Select an Enterasys/Cabletron AP3000 wireless access point as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type apWStationSessionTxPacketCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This is the number of packets transmitted from the client to the AP. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
cabletron	1.3.6.1.4.1.52
mibs	1.3.6.1.4.1.52.4
ctronAP3000	1.3.6.1.4.1.52.4.13			This mib module defines a portion of the SNMP enterprise MIBs under Enterasys Networks enterprise OID as an extension to the Enterasys AP3000 MIB. This Enterasys Networks Proprietary MIB was designed to be used for read-write access to configuration objects in AP3000.
comPortMgnt	1.3.6.1.4.1.52.4.13.1
INT comPortControl	1.3.6.1.4.1.52.4.13.1.1	INTEGER	read-write	The administrative enable/disable state for COM Port Control in a System.
macFilterMgnt	1.3.6.1.4.1.52.4.13.2
macFilterTable	1.3.6.1.4.1.52.4.13.2.1		not-accessible	Table of status information about each configured MAC Filtering Entry.
macFilterEntry	1.3.6.1.4.1.52.4.13.2.1.1		not-accessible	An entry in the table, containing information about configuration of MAC Filter.
I32 macFilterIndex	1.3.6.1.4.1.52.4.13.2.1.1.1	Integer32	not-accessible	Filter index.
MAC macFilterAddress	1.3.6.1.4.1.52.4.13.2.1.1.2	MacAddress	read-write	This values indicates the MAC address of the MAC Filter entry.
INT macFilterAllowedToGo	1.3.6.1.4.1.52.4.13.2.1.1.3	INTEGER	read-write	The administrative allow/deny state for that specified MAC Filter Entry.
INT macFilterOpeStatus	1.3.6.1.4.1.52.4.13.2.1.1.4	INTEGER	read-create	This object indicates the status of this entry. other(0) - this entry is currently in use but the conditions under which it will remain so differ from the following values. valid(1) - this value to indicate this entry is currently in used. invalid(2) - write this value to the corresponding entry, the whole entry will be removed. Since the order of entry shall be re-order while it has been deleted. To re-freshed the whole table is recommended for new index. create(3) - write this value to indicate that the new MAC address will be added after next writing MAC address to that new entry. The adding action will be taken on the index that grater than 1.
INT apMacFilterControl	1.3.6.1.4.1.52.4.13.2.2	INTEGER	read-write	This value indicates the control of the MAC filter setting.
apvMacFilterOperateTable	1.3.6.1.4.1.52.4.13.2.3		not-accessible	The Table used to manage the function in MAC Filter Table.
apvMacFilterOperateEntry	1.3.6.1.4.1.52.4.13.2.3.1		not-accessible	An entry in the table, containing information about configuration in one VAP of the AP.
INT apvMacFilterPermission	1.3.6.1.4.1.52.4.13.2.3.1.1	INTEGER	read-write	This values indicates the Permission on all the active filter entry for each Vap. The negative permission will be applied on any inactive entry or any MAC that is not in the table.
OCT apvMacFilterAddressToAdd	1.3.6.1.4.1.52.4.13.2.3.1.2	OCTET STRING	read-write	This values indicates the MAC address to be added to the local MAC filter table as an active entry for each Vap.
apvMacFilterTable	1.3.6.1.4.1.52.4.13.2.4		not-accessible	Table of status information about each configured MAC Address Filtering Entry.
apvMacFilterEntry	1.3.6.1.4.1.52.4.13.2.4.1		not-accessible	An entry in the table, containing information about configuration in one radio of the AP. MacFilterEntry is created and managed using localMACFilterMgnt Table.
I32 apvMacFilterIndex	1.3.6.1.4.1.52.4.13.2.4.1.1	Integer32	not-accessible	MAC Filter index in each VAP.
MAC apvMacFilterAddress	1.3.6.1.4.1.52.4.13.2.4.1.2	MacAddress	read-only	This values indicates the MAC address of the filter entry.
INT apvMacFilterActivity	1.3.6.1.4.1.52.4.13.2.4.1.3	INTEGER	read-write	This value indicates the Activity of the MAC table entry by the filter permission. If allow(1), the filter permission will be applied to the MAC address. If denied(2), the filter permission will not be applied to the MAC address. If delete_entry(3), the filter entry will be deleted.
qosMgnt	1.3.6.1.4.1.52.4.13.3
INT qosModeControl	1.3.6.1.4.1.52.4.13.3.1	INTEGER	read-write	The administrative status and control of the QoS mode for the QoS management.
qosMACTypeTable	1.3.6.1.4.1.52.4.13.3.2		not-accessible	Table of status information about each configured MAC Type Entry for the QoS Management.
qosMACTypeEntry	1.3.6.1.4.1.52.4.13.3.2.1		not-accessible	An entry in the table, containing information about configuration MAC Type Entry for the QoS Management.
I32 qosMACTypeIndex	1.3.6.1.4.1.52.4.13.3.2.1.1	Integer32	not-accessible	Qos MAC Type index.
MAC qosMACTypeAddress	1.3.6.1.4.1.52.4.13.3.2.1.2	MacAddress	read-write	This values indicates the MAC address of that specified index in the entry.
I32 qosMACTypePriority	1.3.6.1.4.1.52.4.13.3.2.1.3	Integer32	read-write	This values indicates the level of priority of that specified MAC Address in entry.
INT qosMACTypeOpeStatus	1.3.6.1.4.1.52.4.13.3.2.1.4	INTEGER	read-create	This object indicates the status of this entry. other(0) - this entry is currently in use but the conditions under which it will remain so differ from the following values. valid(1) - this value to indicate this entry is currently in used. invalid(2) - write this value to the corresponding entry, the whole entry will be removed. Since the order of entry shall be re-order while it has been deleted. To re-freshed the whole table is recommended for new index. create(3) - write this value to indicate that the new MAC address will be added after next writing MAC address to that new entry. The adding action will be taken on the index that grater than 1.
qosEtherTypeTable	1.3.6.1.4.1.52.4.13.3.3		not-accessible	Table of status information about each configured Ether Type Entry for QoS Management.
qosEtherTypeEntry	1.3.6.1.4.1.52.4.13.3.3.1		not-accessible	An entry in the table, containing information about configuration Ether Type for QoS Management.
I32 qosEtherTypeIndex	1.3.6.1.4.1.52.4.13.3.3.1.1	Integer32	not-accessible	Qos Ether Type index in the table.
OCT qosEtherTypeHexValue	1.3.6.1.4.1.52.4.13.3.3.1.2	OCTET STRING	read-write	The Hex Value to indicate the type of Ether of that specified index in the entry.
I32 qosEtherTypePriority	1.3.6.1.4.1.52.4.13.3.3.1.3	Integer32	read-write	This values indicates the level of priority of that specified MAC Address in entry.
INT qosEtherTypeOpeStatus	1.3.6.1.4.1.52.4.13.3.3.1.4	INTEGER	read-create	This object indicates the status of this entry. other(0) - this entry is currently in use but the conditions under which it will remain so differ from the following values. valid(1) - this value to indicate this entry is currently in used. invalid(2) - write this value to the corresponding entry, the whole entry will be removed. Since the order of entry shall be re-order while it has been deleted. To re-freshed the whole table is recommended for new index. create(3) - write this value to indicate that the new Ether Value will be added after next writing Ether Type Value to that new entry. The adding action will be taken on the index that grater than 1.
INT qosQueueingMode	1.3.6.1.4.1.52.4.13.3.4	INTEGER	read-write	The administrative control of the QoS Queuing mode for the QoS management.
INT qosSVPStatus	1.3.6.1.4.1.52.4.13.3.5	INTEGER	read-write	The administrative enable/disable state for SVP.
linkQualityMgnt	1.3.6.1.4.1.52.4.13.4
linkQualityTable	1.3.6.1.4.1.52.4.13.4.1		not-accessible	Table of status information about the radio Interface Link Quality Entry.
linkQualityEntry	1.3.6.1.4.1.52.4.13.4.1.1		not-accessible	An entry in the table, containing information about configuration of the radio Interface Link Quality.
I32 linkQualityRadioIndex	1.3.6.1.4.1.52.4.13.4.1.1.1	Integer32	not-accessible	This is the value to define the index of the radio interface.
I32 linkQualityStaIndex	1.3.6.1.4.1.52.4.13.4.1.1.2	Integer32	not-accessible	This is value to define the index of link station.
MAC linkQualityStaMacAddress	1.3.6.1.4.1.52.4.13.4.1.1.3	MacAddress	read-only	This values indicates the MAC address of the link station.
I32 linkQualityStaRssi	1.3.6.1.4.1.52.4.13.4.1.1.4	Integer32	read-only	This values indicates the percentage RSSI of the link station.
apSnmpMgnt	1.3.6.1.4.1.52.4.13.5
INT trapControl	1.3.6.1.4.1.52.4.13.5.1	INTEGER	read-write	The administrative enable/disable state for SNMP Trap Control in a System.
trapConfiguration	1.3.6.1.4.1.52.4.13.5.2
INT trapSysSystemUp	1.3.6.1.4.1.52.4.13.5.2.1	INTEGER	read-write	The administrative enable/disable state for SNMP sysSystemUp trap.
INT trapSysSystemDown	1.3.6.1.4.1.52.4.13.5.2.2	INTEGER	read-write	The administrative enable/disable state for SNMP sysSystemDown trap.
INT trapSysRadiusServerChanged	1.3.6.1.4.1.52.4.13.5.2.3	INTEGER	read-write	The administrative enable/disable state for SNMP sysRadiusServerChanged trap.
INT trapDot11StationAssociation	1.3.6.1.4.1.52.4.13.5.2.4	INTEGER	read-write	The administrative enable/disable state for SNMP dot11StationAssociation trap.
INT trapDot11StationReAssociation	1.3.6.1.4.1.52.4.13.5.2.5	INTEGER	read-write	The administrative enable/disable state for SNMP dot11StationReAssociation trap.
INT trapDot11StationAuthentication	1.3.6.1.4.1.52.4.13.5.2.6	INTEGER	read-write	The administrative enable/disable state for SNMP dot11StationAuthentication trap.
INT trapDot11StationRequestFail	1.3.6.1.4.1.52.4.13.5.2.7	INTEGER	read-write	The administrative enable/disable state for SNMP dot11StationRequestFail trap.
INT trapLocalMacAddrAuthFail	1.3.6.1.4.1.52.4.13.5.2.9	INTEGER	read-write	The administrative enable/disable state for SNMP localMacAddrAuthFail trap.
INT trapLocalMacAddrAuthSuccess	1.3.6.1.4.1.52.4.13.5.2.10	INTEGER	read-write	The administrative enable/disable state for SNMP localMacAddrAuthSuccess trap.
INT trapDot1xAuthNotInitiated	1.3.6.1.4.1.52.4.13.5.2.11	INTEGER	read-write	The administrative enable/disable state for SNMP dot1xAuthNotInitiated trap.
INT trapDot1xAuthSuccess	1.3.6.1.4.1.52.4.13.5.2.12	INTEGER	read-write	The administrative enable/disable state for SNMP dot1xAuthSuccess trap.
INT trapDot1xAuthFail	1.3.6.1.4.1.52.4.13.5.2.13	INTEGER	read-write	The administrative enable/disable state for SNMP dot1xAuthFail trap.
INT trapDot1xMacAddrAuthSuccess	1.3.6.1.4.1.52.4.13.5.2.14	INTEGER	read-write	The administrative enable/disable state for SNMP dot1xMacAddrAuthSuccess trap.
INT trapDot1xMacAddrAuthFail	1.3.6.1.4.1.52.4.13.5.2.15	INTEGER	read-write	The administrative enable/disable state for SNMP dot1xMacAddrAuthFail trap.
INT trapPppLogonFail	1.3.6.1.4.1.52.4.13.5.2.16	INTEGER	read-write	The administrative enable/disable state for SNMP pppLogonFail trap.
INT trapIappStationRoamedFrom	1.3.6.1.4.1.52.4.13.5.2.17	INTEGER	read-write	The administrative enable/disable state for SNMP iappStationRoamedFrom trap.
INT trapIappStationRoamedTo	1.3.6.1.4.1.52.4.13.5.2.18	INTEGER	read-write	The administrative enable/disable state for SNMP iappStationRoamedFrom trap.
INT trapIappContextDataSent	1.3.6.1.4.1.52.4.13.5.2.19	INTEGER	read-write	The administrative enable/disable state for SNMP iappContextDataSent trap.
INT trapSntpServerFail	1.3.6.1.4.1.52.4.13.5.2.20	INTEGER	read-write	The administrative enable/disable state for SNMP sntpServerFail trap.
INT trapDot11InterfaceAFail	1.3.6.1.4.1.52.4.13.5.2.21	INTEGER	read-write	The administrative enable/disable state for SNMP dot11InterfaceAFail trap.
INT trapDot11InterfaceGFail	1.3.6.1.4.1.52.4.13.5.2.22	INTEGER	read-write	The administrative enable/disable state for SNMP dot11InterfaceGFail trap.
INT trapDot11WirelessSTPDetection	1.3.6.1.4.1.52.4.13.5.2.23	INTEGER	read-write	The administrative enable/disable state for SNMP dot11WirelessSTPDetection trap.
apSnmpTrapDestinationTable	1.3.6.1.4.1.52.4.13.5.3		not-accessible	Table of descriptive and status information about configuration of each trap receiving server.
apSnmpTrapDestinationEntry	1.3.6.1.4.1.52.4.13.5.3.1		not-accessible	An entry in the table, containing information about configuration of one trap receiving server.
INT apSnmpTrapDestinationIndex	1.3.6.1.4.1.52.4.13.5.3.1.1	INTEGER	not-accessible	Index of the Trap Destination Table.
STR apSnmpTrapDestinationCommunity	1.3.6.1.4.1.52.4.13.5.3.1.2	DisplayString	read-write	The SNMP Trap Community
IP apSnmpTrapDestinationIP	1.3.6.1.4.1.52.4.13.5.3.1.3	IpAddress	read-write	The IP address of the trap receiving server.
INT apSnmpTrapDestinationState	1.3.6.1.4.1.52.4.13.5.3.1.4	INTEGER	read-write	This value indicates whether the trap receiving server is enabled.
STR apSnmpCommunityReadOnly	1.3.6.1.4.1.52.4.13.5.4	DisplayString	read-write	The SNMP Read Only Community. The value if read, will only show ******.
STR apSnmpCommunityReadWrite	1.3.6.1.4.1.52.4.13.5.5	DisplayString	read-write	The SNMP Read Write Community. The value if read, will only show *****.
INT apSnmpVersionFilter	1.3.6.1.4.1.52.4.13.5.6	INTEGER	read-write	To set the version-filter of SNMP.
sysEntity	1.3.6.1.4.1.52.4.13.6
STR swHardwareVer	1.3.6.1.4.1.52.4.13.6.1	DisplayString	read-only	Hardware version of the main board.
STR swBootRomVer	1.3.6.1.4.1.52.4.13.6.2	DisplayString	read-only	Boot ROM code version of the main board.
STR swOpCodeVer	1.3.6.1.4.1.52.4.13.6.3	DisplayString	read-only	Operation code version of the main board.
STR swSerialNumber	1.3.6.1.4.1.52.4.13.6.4	DisplayString	read-only	Serial Number of the Access Point.
STR swProductName	1.3.6.1.4.1.52.4.13.6.5	DisplayString	read-only	The Product Name of the Access Point.
STR swCountrySetting	1.3.6.1.4.1.52.4.13.6.6	DisplayString	read-only	The current CountryCode Setting of the Access Point.
apSecurityMgnt	1.3.6.1.4.1.52.4.13.7
apRadioSecurityTable	1.3.6.1.4.1.52.4.13.7.1		not-accessible	Table of descriptive and status information about configuration of each radio in terms of security settings.
apRadioSecurityEntry	1.3.6.1.4.1.52.4.13.7.1.1		not-accessible	An entry in the table, containing information about configuration of one radio of the AP.
I32 apRadioSecurityIndex	1.3.6.1.4.1.52.4.13.7.1.1.1	Integer32	not-accessible	Radio Index for security settings.
INT apRadioSecurityWEPAuthType	1.3.6.1.4.1.52.4.13.7.1.1.2	INTEGER	read-write	This value indicates the type of WEP authentication in use for this radio interface. opensystem(0) Set authentication open sharedkey(1) Set authentication shared wpa(2) Set WPA Mode wpapsk(3) Set WPA-PSK Mode wpa-wpa2-mixed(4) Set WPA-WPA2-Mixed Mode wpawpa2pskmixed(5) Set WPA-WPA2 PSK Mixed Mode wpa2(6) Set WPA2 Mode wpa2psk(7) Set WPA2-PSK Mode
INT apRadioSecuritySharedKeyLen	1.3.6.1.4.1.52.4.13.7.1.1.3	INTEGER	read-only	This value indicates the shared key length for this radio interface.
INT apRadioSecurityWPAMode	1.3.6.1.4.1.52.4.13.7.1.1.4	INTEGER	read-write	This value indicates the state of WPA for this radio interface.
INT apRadioSecurityWPAKeyType	1.3.6.1.4.1.52.4.13.7.1.1.5	INTEGER	read-write	This value indicates the type of WPA Key Management in use for this radio interface.
INT apRadioSecurityWPACipher	1.3.6.1.4.1.52.4.13.7.1.1.6	INTEGER	read-write	This value indicates the type of WPA Cipher in use for this radio interface.
INT apRadioSecurityWPAPSKType	1.3.6.1.4.1.52.4.13.7.1.1.7	INTEGER	read-write	This value indicates the type of WPA Pre Shared Key in use for this radio interface.
STR apRadioSecurityWPAPSK	1.3.6.1.4.1.52.4.13.7.1.1.8	DisplayString	read-write	This value indicates WPA Pre Shared Key in use for this radio interface.
INT apRadioSecurityWEPKeyType	1.3.6.1.4.1.52.4.13.7.1.1.9	INTEGER	read-write	This value indicates the type of WEP Key in use for this radio interface.
T/F apRadioSecurityWEPEnabled	1.3.6.1.4.1.52.4.13.7.1.1.10	TruthValue	read-write	This value indicates whether WEP is enabled.
INT apRadioSecurityWPACipherSuite	1.3.6.1.4.1.52.4.13.7.1.1.11	INTEGER	read-write	This value indicates the type of WPA Cipher Suite in use for this radio interface.
INT apRadioApSecurityWPAPreAuthentication	1.3.6.1.4.1.52.4.13.7.1.1.12	INTEGER	read-write	Whether Pre-Authentication is enabled.
INT apRadioApSecurityWPAPmksaLifetime	1.3.6.1.4.1.52.4.13.7.1.1.13	INTEGER	read-write	The number (in minutes) for Pmksa-Lifetime.
apSecuritySsh	1.3.6.1.4.1.52.4.13.7.2
T/F apSecuritySshServerEnabled	1.3.6.1.4.1.52.4.13.7.2.1	TruthValue	read-write	This value indicates whether SSH server is enabled.
I32 apSecuritySshServerPort	1.3.6.1.4.1.52.4.13.7.2.2	Integer32	read-write	This value indicates SSH server's port number.
T/F apSecuritySshTelnetServerEnabled	1.3.6.1.4.1.52.4.13.7.2.3	TruthValue	read-write	This value indicates whether telnet server is enabled.
apRadioInterfaceMgnt	1.3.6.1.4.1.52.4.13.8
enterpriseApRadioTable	1.3.6.1.4.1.52.4.13.8.2		not-accessible	Table of descriptive and status information about configuration of each radio.
enterpriseApRadioEntry	1.3.6.1.4.1.52.4.13.8.2.1		not-accessible	An entry in the table, containing information about configuration of one radio of the AP.
I32 enterpriseApRadioIndex	1.3.6.1.4.1.52.4.13.8.2.1.1	Integer32	not-accessible	Radio Index for configuration.
INT enterpriseApRadioAutoChannel	1.3.6.1.4.1.52.4.13.8.2.1.2	INTEGER	read-write	This value indicates whether auto channel selection is enabled or not for this radio interface
INT enterpriseApRadioTransmitPower	1.3.6.1.4.1.52.4.13.8.2.1.3	INTEGER	read-write	This value indicates the transmit power for this radio interface.
INT enterpriseApRadioTurboMode	1.3.6.1.4.1.52.4.13.8.2.1.4	INTEGER	read-write	This value indicates whether turbo mode is enabled for this radio interface.
INT enterpriseApRadioDataRate	1.3.6.1.4.1.52.4.13.8.2.1.5	INTEGER	read-write	This value indicates the data rate for this radio interface. Radio interface A operates at 6, 9, 12, 18, 24, 36, 48, 54. Radio interface G operates all listed data rates. The auto setting will attempt to set the best data rate for the interface
INT enterpriseApRadioGMode	1.3.6.1.4.1.52.4.13.8.2.1.6	INTEGER	read-write	This value indicates the radio mode for the 802.11g radio. This setting is only valid for the 802.11g interface.
INT enterpriseApRadioAntennaMode	1.3.6.1.4.1.52.4.13.8.2.1.7	INTEGER	read-write	This value indicates the antenna mode in use for the G-radio. The values are interpreted as follows: both(1) means use both built-in antennas, left(2) means use left side. right(3) means use right side. invalid(4) means not support. This setting is only valid for the 802.11g interface.
INT rogueApState	1.3.6.1.4.1.52.4.13.8.2.1.8	INTEGER	read-write	This value is used to enable/disable Rogue Ap Detection for this radio interface.
INT rogueApInterval	1.3.6.1.4.1.52.4.13.8.2.1.9	INTEGER	read-write	How often to scan for Rogue Aps. The interval in minutes, with default of 720(minutes).
INT rogueApDuration	1.3.6.1.4.1.52.4.13.8.2.1.10	INTEGER	read-write	How long to scan each channel (in milliseconds). A longer duration will yield more complete results. A shorter duration will allow clients a better chance of remaining connected. Default value is 350(milliseconds).
INT rogueApScanNow	1.3.6.1.4.1.52.4.13.8.2.1.11	INTEGER	read-write	When writing the value to enable, the AP will trigger the Rouge AP scan function. The value will always return disable(2).
INT enterpriseApRadioAntennaModeControl	1.3.6.1.4.1.52.4.13.8.2.1.12	INTEGER	read-only	This value indicates which antenna is in use for the radio Interface. The values are interpreted as follows: fixed(1) specify to use built-in antennas, external(2) specify to use one external antenna.
INT enterpriseApRadioFixedAntennaType	1.3.6.1.4.1.52.4.13.8.2.1.13	INTEGER	read-write	This value indicates which antenna type is in use as the fixed antenna is selected.
INT enterpriseApRadioAntennaID	1.3.6.1.4.1.52.4.13.8.2.1.14	INTEGER	read-write	This value indicates which antenna ID will be in use for the radio Interface.
INT enterpriseApRadioMulticastDataRate	1.3.6.1.4.1.52.4.13.8.2.1.15	INTEGER	read-write	This value indicates the data rate for mc/bc packets from this radio interface. sixMbps(6), nineMbps(9), twelveMbps(12), eighteenMbps(18), twentyFourMbps(24), thirtySixMbps(36), fortyEightMbps(48), and fiftyFourMbps(54) are for 11a and g-only mode. The default for b-only and b+g mode is oneMbps(1), twoMbps(2), fiveAndHalfMbps(5) and elevenMbps(11).
INT enterpriseApRadioAutoDataRate	1.3.6.1.4.1.52.4.13.8.2.1.16	INTEGER	read-write	This value indicates whether automated data rate is enabled or not for this radio interface
INT enterpriseApRadioPreamble	1.3.6.1.4.1.52.4.13.8.2.1.17	INTEGER	read-write	This value indicates the preamble length of 11g. The values are interpreted as follows: long(1) sets the preamble length to long. short(2) sets the preamble length to short. invalid(3) means not support. This setting is only valid for the 802.11g interface.
INT enterpriseApRadioSWRetryMode	1.3.6.1.4.1.52.4.13.8.2.1.18	INTEGER	read-write	This value indicates whether SW retty mode is enabled or not for this radio interface
enterpriseApVapRadioTable	1.3.6.1.4.1.52.4.13.8.3		not-accessible	Table of descriptive and status information about configuration of each Vap radio.
enterpriseApVapRadioEntry	1.3.6.1.4.1.52.4.13.8.3.1		not-accessible	An entry in the table, containing information about configuration of one Vap radio of the AP.
I32 enterpriseApVapRadioIndex	1.3.6.1.4.1.52.4.13.8.3.1.1	Integer32	not-accessible	Radio Index for configuration.
INT enterpriseApVapRadioState	1.3.6.1.4.1.52.4.13.8.3.1.2	INTEGER	read-write	This value indicates the state of the radio interface.
INT enterpriseApVapRadioSecureAccess	1.3.6.1.4.1.52.4.13.8.3.1.3	INTEGER	read-write	This value indicates whether secure access is enabled for this radio interface.
INT enterpriseApVapRadioMaxAssoc	1.3.6.1.4.1.52.4.13.8.3.1.4	INTEGER	read-write	This value indicates the max number of clients allowed on this radio interface.
INT enterpriseApVapRadioTransmitKey	1.3.6.1.4.1.52.4.13.8.3.1.5	INTEGER	read-write	This value indicates default transmit key in use for this radio interface.
STR enterpriseApVapRadioDescription	1.3.6.1.4.1.52.4.13.8.3.1.6	DisplayString	read-write	This value indicates the description for this radio interface.
I32 enterpriseApVapRadioDefefaultPriority	1.3.6.1.4.1.52.4.13.8.3.1.7	Integer32	read-write	This values indicates the level of default priority of that specified VAP in entry.
enterpriseApRadioWdsTable	1.3.6.1.4.1.52.4.13.8.4		not-accessible	Table of configuration information for Wds for each Radio interface.
enterpriseApRadioWdsEntry	1.3.6.1.4.1.52.4.13.8.4.1		not-accessible	An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding to enterpriseApRadioTable). The table does not contain the radio index as a member of the table.
INT wdsApRole	1.3.6.1.4.1.52.4.13.8.4.1.1	INTEGER	read-write	This value indicates the role of the Ap for this radio, roleAp(1): AP operation. roleBridgeMaster(2): Root-Bridge mode. roleBridge(3): Bridge Mode.
INT wdsApAckTimeout	1.3.6.1.4.1.52.4.13.8.4.1.2	INTEGER	read-write	This value indicates the WDS Ack timeout for this radio in us, and the following values can be set to the system: 0 Set wireless Ack Timeout as system default 20 0 to 1 miles: Ack timeout is 20 us 40 1 to 3 miles: Ack timeout is 40 us 75 3 to 6 miles: Ack timeout is 75 us 115 6 to 10 miles: Ack timeout is 115 us
enterpriseApRadioWdsPeerTable	1.3.6.1.4.1.52.4.13.8.5		not-accessible	Table of configuration information for Wds Peers for each Radio interface.
enterpriseApRadioWdsPeerEntry	1.3.6.1.4.1.52.4.13.8.5.1		not-accessible	An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding to enterpriseApRadioTable) and the peer index (Up to 8). The table does not contain the radio index as a member of the table.
I32 wdsPeerIndex	1.3.6.1.4.1.52.4.13.8.5.1.1	Integer32	not-accessible	Peer Index for the radio interface.
STR wdsPeerBssid	1.3.6.1.4.1.52.4.13.8.5.1.2	DisplayString	read-write	The BSSID for this peer.
I32 wdsPeerRSSI	1.3.6.1.4.1.52.4.13.8.5.1.3	Integer32	read-only	This value indicates the RSSI value of the WDS peer link.
enterpriseApRadioWEPKeysTable	1.3.6.1.4.1.52.4.13.8.6		not-accessible	Conceptual table for WEP default keys.
enterpriseApRadioWEPKeysEntry	1.3.6.1.4.1.52.4.13.8.6.1		not-accessible	An Entry (conceptual row) in the WEP Default Keys Table. A collection of objects containing information used to determine if a WEPkey as been defined and if so, the value of the WEPkey.
INT enterpriseApRadioWEPKeysIndex	1.3.6.1.4.1.52.4.13.8.6.1.1	INTEGER	not-accessible	WEP Key Index for the radio interface.
INT enterpriseApRadioWEPKeyType	1.3.6.1.4.1.52.4.13.8.6.1.2	INTEGER	read-only	status of the WEP Key type
INT enterpriseApRadioWEPKeyLength	1.3.6.1.4.1.52.4.13.8.6.1.3	INTEGER	read-only	status of the WEP Key Length.
enterpriseApRadioAvAntennaListTable	1.3.6.1.4.1.52.4.13.8.7		not-accessible	Conceptual table for Available Antenna List used in the Radio.
enterpriseApRadioAvAntennaListEntry	1.3.6.1.4.1.52.4.13.8.7.1		not-accessible	An Entry (conceptual row) in the Antenna List Table. A collection of objects containing information used to show if an Antenna as been defined and if so, the value of the antenna Id.
INT enterpriseApRadioAvAntennaIndex	1.3.6.1.4.1.52.4.13.8.7.1.1	INTEGER	not-accessible	Available Antenna List Index for the radio interface.
INT enterpriseApRadioAvAntennaId	1.3.6.1.4.1.52.4.13.8.7.1.2	INTEGER	read-only	Available antenna Id in the entry.
STR enterpriseApRadioAvAntennaDesc	1.3.6.1.4.1.52.4.13.8.7.1.3	DisplayString	read-only	The description of the antenna ID.
enterpriseApRadioAvChannelListTable	1.3.6.1.4.1.52.4.13.8.8		not-accessible	Conceptual table for Available Channel List used in the Radio.
enterpriseApRadioAvChannelListEntry	1.3.6.1.4.1.52.4.13.8.8.1		not-accessible	An Entry (conceptual row) in the Channel List Table. A collection of objects containing information used to show if a Channel No. as been defined and if so, the value of the Channel No.
INT enterpriseApRadioAvChannelIndex	1.3.6.1.4.1.52.4.13.8.8.1.1	INTEGER	not-accessible	Channel List Index for the radio interface.
INT enterpriseApRadioAvChannelNo	1.3.6.1.4.1.52.4.13.8.8.1.2	INTEGER	read-only	Available channel number in the entry
apEtherInterfaceMgnt	1.3.6.1.4.1.52.4.13.9
apEtherNetConfig	1.3.6.1.4.1.52.4.13.9.1
IP netConfigIPAddress	1.3.6.1.4.1.52.4.13.9.1.1	IpAddress	read-write	The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
IP netConfigSubnetMask	1.3.6.1.4.1.52.4.13.9.1.2	IpAddress	read-write	The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
IP netConfigDefaultGateway	1.3.6.1.4.1.52.4.13.9.1.3	IpAddress	read-write	The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
INT netConfigHttpState	1.3.6.1.4.1.52.4.13.9.1.4	INTEGER	read-write	Whether HTTP is enabled.
INT netConfigHttpPort	1.3.6.1.4.1.52.4.13.9.1.5	INTEGER	read-write	The port number for HTTP.
INT netConfigHttpsState	1.3.6.1.4.1.52.4.13.9.1.6	INTEGER	read-write	Whether Secure HTTP is enabled.
INT netConfigHttpsPort	1.3.6.1.4.1.52.4.13.9.1.7	INTEGER	read-write	The port number for Secure HTTP.
INT netConfigDHCPState	1.3.6.1.4.1.52.4.13.9.1.8	INTEGER	read-write	Whether DHCP is enabled.
apFilterControlMgnt	1.3.6.1.4.1.52.4.13.10
INT apFilterControlBridge	1.3.6.1.4.1.52.4.13.10.1	INTEGER	read-write	This value indicates the local bridge filter setting.
INT enterpriseApFilterControlAPManage	1.3.6.1.4.1.52.4.13.10.2	INTEGER	read-write	This value indicates the AP management filter setting.
INT enterpriseApFilterControlEthernet	1.3.6.1.4.1.52.4.13.10.3	INTEGER	read-write	This value indicates the ethernet filter setting.
enterpriseApFilterProtocolTable	1.3.6.1.4.1.52.4.13.10.4		not-accessible	Table of descriptive and status information about configuration of the filter protocol table.
enterpriseApFilterProtocolEntry	1.3.6.1.4.1.52.4.13.10.4.1		not-accessible	An entry in the filter protocol table, containing information about configuration of one filter table entry.
I32 enterpriseApFilterProtocolIndex	1.3.6.1.4.1.52.4.13.10.4.1.1	Integer32	not-accessible	Index of the Protocol Filters.
STR enterpriseApFilterProtocolName	1.3.6.1.4.1.52.4.13.10.4.1.2	DisplayString	read-only	This value indicates the name of the protocol filter. One of the following: Aironet_DDP, Appletalk_ARP, ARP, Banyan, Berkeley_Trailer_Negotiation, CDP, DEC_LAT, DEC_MOP, DEC_MOP_Dump_Load, DEC_XNS, EAPOL, Enet_Config_Test, Ethertalk, IP, LAN_Test, NetBEUI, Novell_IPX(new), Novell_IPX(old), RARP, Telxon_TXP, X.25_Level3
STR enterpriseApFilterProtocolISODesignator	1.3.6.1.4.1.52.4.13.10.4.1.3	DisplayString	read-only	This value indicates the name of the protocol filter.
INT enterpriseApFilterProtocolState	1.3.6.1.4.1.52.4.13.10.4.1.4	INTEGER	read-write	This value indicates whether the protocol filter is enabled.
INT apvGlobalIBSSRelayMode	1.3.6.1.4.1.52.4.13.10.5	INTEGER	read-write	This value indicates the setting of the global IBSS Relay mode among the VAPs. In Per-VAP Mode enable, the traffic between the VAPs should be blocked. In Al-VAP Mode enable, the traffic between should not be blocked.
apvFilterControlTable	1.3.6.1.4.1.52.4.13.10.6		not-accessible	Table of the control and status information about configuration of the filter Control for each Vap.
apvFilterControlEntry	1.3.6.1.4.1.52.4.13.10.6.1		not-accessible	An entry in the table, containing information about configuration of the filter for each Vap of the AP.
I32 apvFilterControlIndex	1.3.6.1.4.1.52.4.13.10.6.1.1	Integer32	not-accessible	Index of the configuration.
INT apvIBSSFilterControl	1.3.6.1.4.1.52.4.13.10.6.1.2	INTEGER	read-write	This value indicates the local bridge filter(IBSS Relay Filter) setting.
INT apvAPManageFilterControl	1.3.6.1.4.1.52.4.13.10.6.1.3	INTEGER	read-write	This value indicates the AP management filter setting.
apVLANMgnt	1.3.6.1.4.1.52.4.13.11
INT apVLANMgntNativeId	1.3.6.1.4.1.52.4.13.11.1	INTEGER	read-write	This value indicates the native VLAN Id.
INT apVLANMgntState	1.3.6.1.4.1.52.4.13.11.2	INTEGER	read-only	This value indicates whether VLANs are enabled or disabled.
INT apVLANMgntStateNextBoot	1.3.6.1.4.1.52.4.13.11.3	INTEGER	read-write	This value indicates the VLANs state for the next reset.
apNativeVlanTable	1.3.6.1.4.1.52.4.13.11.6		not-accessible	Table used to manage the Vlans for each wireless interface.
apNativeVlanEntry	1.3.6.1.4.1.52.4.13.11.6.1		not-accessible	An entry in the table, containing information about VLAN configuration of one wireless interface.
I32 apNativeVlanIfIndex	1.3.6.1.4.1.52.4.13.11.6.1.1	Integer32	not-accessible	Interface Index of the wireless interface for which the VLAN is assigned to.
I32 apNativeVlanSsidNumber	1.3.6.1.4.1.52.4.13.11.6.1.2	Integer32	not-accessible	Associated Number for Service Set Id (SSID) of the wireless interface for which the VLAN is assigned to. Note: This is for future support of multiple SSIDs per radio interface.
I32 apNativeVlanVlanId	1.3.6.1.4.1.52.4.13.11.6.1.3	Integer32	read-write	This value indicates the native VLAN Id of the wireless interface associated with the if index and the SSID number(if it is not 0).
INT apNativeVlanState	1.3.6.1.4.1.52.4.13.11.6.1.4	INTEGER	read-write	This value indicates the Native VLANs state.
I32 apVLANMgntEtherUntaggedVlanId	1.3.6.1.4.1.52.4.13.11.7	Integer32	read-write	This value indicates the Untagged VlanID for Ether Interface.
apAuthenticationMgnt	1.3.6.1.4.1.52.4.13.12
apAuthenticationSetupEntry	1.3.6.1.4.1.52.4.13.12.1
INT ap8021xState	1.3.6.1.4.1.52.4.13.12.1.1	INTEGER	read-write	This attribute indicates that the Enterprise the state of the 802.1X authentication algorithm.
INT ap8021xBroadcastKeyRefreshRate	1.3.6.1.4.1.52.4.13.12.1.2	INTEGER	read-write	The number (in minutes) between changing the broadcast key for 802.1X and WPA clients
INT ap8021xSessionKeyRefreshRate	1.3.6.1.4.1.52.4.13.12.1.3	INTEGER	read-write	The number (in minutes) between changing session keys for 802.1X and WPA clients
INT ap8021xReauthenticationTimeout	1.3.6.1.4.1.52.4.13.12.1.4	INTEGER	read-write	The number (in minutes) between forcing 802.1X clients to reauthenticate
INT apAuthenticationMode	1.3.6.1.4.1.52.4.13.12.1.5	INTEGER	read-write	This value indicates the type of MAC authentication or RADIUS authentication in use, or not in use.
apAuthenticationServerTable	1.3.6.1.4.1.52.4.13.12.2		not-accessible	Table of descriptive and status information about configuration of each authentication server.
apAuthenticationServerEntry	1.3.6.1.4.1.52.4.13.12.2.1		not-accessible	An entry in the table, containing information about configuration of one authentication server of the AP.
I32 apAuthenticationServerIndex	1.3.6.1.4.1.52.4.13.12.2.1.1	Integer32	not-accessible	Index of the Authentication Server
STR apAuthenticationServer	1.3.6.1.4.1.52.4.13.12.2.1.2	DisplayString	read-write	This value indicates the IP address or host name of the authentication server.
INT apAuthenticationPort	1.3.6.1.4.1.52.4.13.12.2.1.3	INTEGER	read-write	This value indicates the UDP Port used by the authentication server.
STR apAuthenticationKey	1.3.6.1.4.1.52.4.13.12.2.1.4	DisplayString	read-write	This value indicates the shared key used by the authentication server.
INT apAuthenticationRetransmit	1.3.6.1.4.1.52.4.13.12.2.1.5	INTEGER	read-write	This value indicates the retransmit timer length used by the authentication server.
INT apAuthenticationTimeout	1.3.6.1.4.1.52.4.13.12.2.1.6	INTEGER	read-write	This value indicates the Timeout value(sec) used by the authentication server.
INT apAuthenticationAcctPort	1.3.6.1.4.1.52.4.13.12.2.1.7	INTEGER	read-write	UDP Accounting Port. The valid range is from 1024-65535. A value of 0 means accounting is disabled.
INT apAuthenticationAcctInterimUpdate	1.3.6.1.4.1.52.4.13.12.2.1.8	INTEGER	read-write	The interval between sending accounting updates.
INT apAuthenticationAcctState	1.3.6.1.4.1.52.4.13.12.2.1.9	INTEGER	read-write	This value indicates whether the Accounting Server is enabled.
apAuthenticationSupplicantTable	1.3.6.1.4.1.52.4.13.12.3		not-accessible	Table of descriptive and status information about configuration of supplicant
apAuthenticationSupplicantEntry	1.3.6.1.4.1.52.4.13.12.3.1		not-accessible	An entry in the table, containing information about configuration of one supplicant.
I32 ap8021xSuppIndex	1.3.6.1.4.1.52.4.13.12.3.1.1	Integer32	not-accessible	Index of the interface for which this supplicant is running. Currently only the ethernet interface.
INT ap8021xSuppState	1.3.6.1.4.1.52.4.13.12.3.1.2	INTEGER	read-write	This object is used to enable or disable the 802.1X supplicant.
STR ap8021xSuppUser	1.3.6.1.4.1.52.4.13.12.3.1.3	DisplayString	read-write	This value indicates the username for supplicant. If value is configured, will display ****. Else will display EMPTY.
STR ap8021xSuppPasswd	1.3.6.1.4.1.52.4.13.12.3.1.4	DisplayString	read-write	This value indicates the password for supplicant. If value is configured, will display ****. Else will display EMPTY.
apvAuthenticationSetupTable	1.3.6.1.4.1.52.4.13.12.4		not-accessible	Table of descriptive and status information about configuration of 8021x for each Vap.
apvAuthenticationSetupEntry	1.3.6.1.4.1.52.4.13.12.4.1		not-accessible	An entry in the table, containing information about configuration of 8021x for each Vap of the AP.
I32 apv8021xIndex	1.3.6.1.4.1.52.4.13.12.4.1.1	Integer32	not-accessible	Index for configuration.
INT apv8021xState	1.3.6.1.4.1.52.4.13.12.4.1.2	INTEGER	read-write	This attribute indicates that the Enterprise the state of the 802.1X authentication algorithm.
INT apv8021xBroadcastKeyRefreshRate	1.3.6.1.4.1.52.4.13.12.4.1.3	INTEGER	read-write	The number (in minutes) between changing the broadcast key for 802.1X and WPA clients
INT apv8021xSessionKeyRefreshRate	1.3.6.1.4.1.52.4.13.12.4.1.4	INTEGER	read-write	The number (in minutes) between changing history keys for 802.1X and WPA clients
INT apv8021xReauthenticationTimeout	1.3.6.1.4.1.52.4.13.12.4.1.5	INTEGER	read-write	The number (in minutes) between forcing 802.1X clients to reauthenticate
INT apvMACAuthenticationMode	1.3.6.1.4.1.52.4.13.12.4.1.6	INTEGER	read-write	This value indicates the mode of MAC authentication in use.
INT apvMACAuthenticationTimeout	1.3.6.1.4.1.52.4.13.12.4.1.7	INTEGER	read-write	The number (in minutes) between forcing RADIUS MAC to authenticate.
STR apvMACAuthenticationPasswd	1.3.6.1.4.1.52.4.13.12.4.1.8	DisplayString	read-write	This value indicates the password for MAC RADIUS Authentication. If value is configured, will display ****. Else will display EMPTY.
apWStationSessionMgnt	1.3.6.1.4.1.52.4.13.13
apWStationSessionTable	1.3.6.1.4.1.52.4.13.13.1		not-accessible	This table list all sessions (wireless stations) status
apWStationSessionEntry	1.3.6.1.4.1.52.4.13.13.1.1		not-accessible	An entry in the table, containing information about status and statistics of the wireless station.
I32 apWStationSessionIfIndex	1.3.6.1.4.1.52.4.13.13.1.1.1	Integer32	not-accessible	Interface index for the radio this session is associated with.
MAC apWStationSessionStationAddres	1.3.6.1.4.1.52.4.13.13.1.1.2	MacAddress	not-accessible	The unique MAC Address of the station for this session.
T/F apWStationSessionAuthenticated	1.3.6.1.4.1.52.4.13.13.1.1.3	TruthValue	read-only	Whether the session is authenticated or not.
T/F apWStationSessionAssociated	1.3.6.1.4.1.52.4.13.13.1.1.4	TruthValue	read-only	Whether the session is associated or not. It is rare case that not associated stations show up in the table.
T/F apWStationSessionIsForwarding	1.3.6.1.4.1.52.4.13.13.1.1.5	TruthValue	read-only	Whether the AP is forwarding the client station traffic (higher level authentication)
INT apWStationSessionKeyType	1.3.6.1.4.1.52.4.13.13.1.1.6	INTEGER	read-only	The encryption key type used by the station. Note that wpa-wep is not supported
I32 apWStationSessionAssociationId	1.3.6.1.4.1.52.4.13.13.1.1.7	Integer32	read-only	The internal association identify number
TIK apWStationSessionLastAuthenticatedTime	1.3.6.1.4.1.52.4.13.13.1.1.8	TimeTicks	read-only	This is the time in hundredths of a second last time the client is authenticated. Note that a session may be authenticated multiple times. The value is related to the system startup
TIK apWStationSessionAssociatedTime	1.3.6.1.4.1.52.4.13.13.1.1.9	TimeTicks	read-only	This is the time in hundredths of a second since the client associated. The value is related to the system startup
TIK apWStationSessionLastAssociatedTime	1.3.6.1.4.1.52.4.13.13.1.1.10	TimeTicks	read-only	This is the time in hundredths of a second when the client associated in last session. The value is related to the system startup
TIK apWStationSessionLastDisassociatedTime	1.3.6.1.4.1.52.4.13.13.1.1.11	TimeTicks	read-only	This is the time in hundredths of a second when the client disassociated in last session. The value is related to the system startup
C32 apWStationSessionTxPacketCountEx	1.3.6.1.4.1.52.4.13.13.1.1.12	Counter32	read-only	This is the number of packets transmitted from the client to the AP. It includes data, control and management packets.
C32 apWStationSessionRxPacketCount	1.3.6.1.4.1.52.4.13.13.1.1.13	Counter32	read-only	This is the number of unicast packets transmitted from the AP to the client. It includes data, control and management packets.
C32 apWStationSessionTxByteCount	1.3.6.1.4.1.52.4.13.13.1.1.14	Counter32	read-only	This is the number of bytes transmitted from the client to the AP. It includes the bytes of data, control and management packets.
C32 apWStationSessionRxByteCount	1.3.6.1.4.1.52.4.13.13.1.1.15	Counter32	read-only	This is the number of unicast bytes transmitted from the AP to the client. It includes the bytes of data, control and management packets.
INT apWStationSessionVlanID	1.3.6.1.4.1.52.4.13.13.1.1.16	INTEGER	read-only	The current VLAN Id used by the station.
apRogueApMgnt	1.3.6.1.4.1.52.4.13.14
rogueApDetectionTable	1.3.6.1.4.1.52.4.13.14.1		not-accessible	Table of each AP that has been detected.
rogueApDetectionEntry	1.3.6.1.4.1.52.4.13.14.1.1		not-accessible	An entry in the table, containing information about any AP detected.
INT rogueApIndex	1.3.6.1.4.1.52.4.13.14.1.1.1	INTEGER	not-accessible	Monotonically increasing index.
STR rogueApBssid	1.3.6.1.4.1.52.4.13.14.1.1.2	DisplayString	read-only	The AP BSSID
STR rogueApSsid	1.3.6.1.4.1.52.4.13.14.1.1.3	DisplayString	read-only	The AP SSID
I32 rogueApPortNumber	1.3.6.1.4.1.52.4.13.14.1.1.4	Integer32	read-only	Interface index for the radio.
I32 rogueApChannelNumber	1.3.6.1.4.1.52.4.13.14.1.1.5	Integer32	read-only	Channel where Ap detected.
I32 rogueApRSSIValue	1.3.6.1.4.1.52.4.13.14.1.1.6	Integer32	read-only	RSSI for AP detected.
apRougeApControl	1.3.6.1.4.1.52.4.13.14.2
INT rogueApRADIUSAuthenticate	1.3.6.1.4.1.52.4.13.14.2.1	INTEGER	read-write	Value is used to enable/disable RADIUS Authentication.
INT rogueApClear	1.3.6.1.4.1.52.4.13.14.2.2	INTEGER	read-write	This object is set to clear(1) to clear the Rogue AP detection table. When read, the value will have no meaning.
apAdminMgnt	1.3.6.1.4.1.52.4.13.15
STR apAdminUsername	1.3.6.1.4.1.52.4.13.15.1	DisplayString	read-write	This value indicates the username for management login.
STR appAdminPassword	1.3.6.1.4.1.52.4.13.15.2	DisplayString	read-write	This value indicates the password for management login.
apResetMgt	1.3.6.1.4.1.52.4.13.16
STR apRestartOpCodeFile	1.3.6.1.4.1.52.4.13.16.1	DisplayString	read-write	Name of op-code file for start-up.
INT apRestartControl	1.3.6.1.4.1.52.4.13.16.2	INTEGER	read-write	Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Setting this object to coldBoot(3) causes the device to reinitialize configuration parameters in non-volatile memory to default values and restart the application software. When the device is running normally, this variable has a value of running(1).
apSNTPMgnt	1.3.6.1.4.1.52.4.13.17
INT apSNTPState	1.3.6.1.4.1.52.4.13.17.1	INTEGER	read-write	This value indicates whether SNTP is enabled or not. At least one of the SNTP servers must have a valid IP address before SNTP can be enabled.
IP apSNTPPrimaryServer	1.3.6.1.4.1.52.4.13.17.2	IpAddress	read-write	This value indicates the IP address of the primary SNTP server.
IP apSNTPSecondaryServer	1.3.6.1.4.1.52.4.13.17.3	IpAddress	read-write	This value indicates the IP address of the secondary SNTP server.
INT apSNTPTimezone	1.3.6.1.4.1.52.4.13.17.4	INTEGER	read-write	This value indicates which timezone to use.
INT apSNTPDST	1.3.6.1.4.1.52.4.13.17.5	INTEGER	read-write	This value indicates whether Daylight Savings Time is enabled or not.
INT apSNTPDSTStartMonth	1.3.6.1.4.1.52.4.13.17.6	INTEGER	read-write	This value indicates the starting month for Daylight Savings Time.
INT apSNTPDSTStartDay	1.3.6.1.4.1.52.4.13.17.7	INTEGER	read-write	This value indicates the starting day for Daylight Savings Time.
INT apSNTPDSTEndMonth	1.3.6.1.4.1.52.4.13.17.8	INTEGER	read-write	This value indicates the ending month for Daylight Savings Time.
INT apSNTPDSTEndDay	1.3.6.1.4.1.52.4.13.17.9	INTEGER	read-write	This value indicates the ending day for Daylight Savings Time.
apDNSMgnt	1.3.6.1.4.1.52.4.13.18
IP apDNSPrimaryServer	1.3.6.1.4.1.52.4.13.18.1	IpAddress	read-write	This value indicates the IP address of the primary DNS server.
IP apDNSSecondaryServer	1.3.6.1.4.1.52.4.13.18.2	IpAddress	read-write	This value indicates the IP address of the secondary DNS server.
apIappMgnt	1.3.6.1.4.1.52.4.13.19
INT apIappEnabled	1.3.6.1.4.1.52.4.13.19.1	INTEGER	read-write	Whether IAPP is enabled.
apSyslogConfigMgnt	1.3.6.1.4.1.52.4.13.20
INT apLogConfigState	1.3.6.1.4.1.52.4.13.20.1	INTEGER	read-write	This value indicates whether syslog is enabled.
INT apSyslogConsoleState	1.3.6.1.4.1.52.4.13.20.2	INTEGER	read-write	This value indicates whether syslog console logging is enabled.
INT apSyslogLevel	1.3.6.1.4.1.52.4.13.20.3	INTEGER	read-write	This value indicates the syslog logging level.
apSyslogServerTable	1.3.6.1.4.1.52.4.13.20.4		not-accessible	Table of descriptive and status information about configuration of each syslog server.
apSyslogServerEntry	1.3.6.1.4.1.52.4.13.20.4.1		not-accessible	An entry in the table, containing information about configuration of one syslog server of the AP.
I32 apSyslogServerIndex	1.3.6.1.4.1.52.4.13.20.4.1.1	Integer32	not-accessible	Index of the Syslog Server
INT apSyslogServerState	1.3.6.1.4.1.52.4.13.20.4.1.2	INTEGER	read-write	This value indicates whether the syslog server is enabled.
STR apSyslogServerIPAddress	1.3.6.1.4.1.52.4.13.20.4.1.3	DisplayString	read-write	This value indicates the IP address of the syslog server.
INT apSyslogServerPort	1.3.6.1.4.1.52.4.13.20.4.1.4	INTEGER	read-write	This value indicates the UDP Port used by the syslog server.
apEventLogMgnt	1.3.6.1.4.1.52.4.13.21
apEventLogTable	1.3.6.1.4.1.52.4.13.21.1		not-accessible	This table is a snapshot of the current event log.
apEventLogEntry	1.3.6.1.4.1.52.4.13.21.1.1		not-accessible	An entry in the table, containing one message from the event log.
INT apEventLogIndex	1.3.6.1.4.1.52.4.13.21.1.1.1	INTEGER	not-accessible	Index of the Event Log Message
STR apEventLogMessage	1.3.6.1.4.1.52.4.13.21.1.1.2	DisplayString	read-only	The Event Log Message
INT apEventLogClear	1.3.6.1.4.1.52.4.13.21.2	INTEGER	read-write	This object is set to 1 to clear the event log. When read, the value will have no meaning.
apWSLSupportMgnt	1.3.6.1.4.1.52.4.13.22
INT apWSLSupportControl	1.3.6.1.4.1.52.4.13.22.1	INTEGER	read-write	The administrative enable/disable state for the control of the WSL function.
STR apWSLSupportMasterAddress	1.3.6.1.4.1.52.4.13.22.2	DisplayString	read-write	This value indicates IP address of the main WSL.
STR apWSLSupportSecondaryAddress	1.3.6.1.4.1.52.4.13.22.3	DisplayString	read-write	This value indicates IP address of the peer WSL.
INT apWSLSupportPort	1.3.6.1.4.1.52.4.13.22.4	INTEGER	read-write	This value indicates the TCP Port used by the WSL server.
INT apWSLSupportHeartbeatInterval	1.3.6.1.4.1.52.4.13.22.5	INTEGER	read-write	This value indicates the WSL Heartbeat Interval.
STR apWSLSupportHeartbeatLastChange	1.3.6.1.4.1.52.4.13.22.6	DisplayString	read-only	The sysUpTime at which the Heartbeat was last modified. The format is defined as hh:mm:ss - dd:mm:yy
INT apWSLSupportOperationMode	1.3.6.1.4.1.52.4.13.22.7	INTEGER	read-write	This attribute indicates that the WSL Operation Mode in 0: AP in standalone mode, or 1: AP in ETS WSL managed mode (associated mode).
INT apWSLSupportRxThreshold	1.3.6.1.4.1.52.4.13.22.8	INTEGER	read-write	This value indicates the WSL CCA rejection threshold in dBm scale.
INT apWSLSupportControlStatus	1.3.6.1.4.1.52.4.13.22.9	INTEGER	read-only	The operative enable/disable state for the control of the WSL function.
INT apWSLRFAreaPollControl	1.3.6.1.4.1.52.4.13.22.10	INTEGER	read-only	The administrative enable/disable state for the control of the WSL RF Area Poll function.
INT apWSLRFAreaPollControlStatus	1.3.6.1.4.1.52.4.13.22.11	INTEGER	read-only	The operative enable/disable state for the control of the WSL RF Area Poll function.
apWMMMgnt	1.3.6.1.4.1.52.4.13.23
apWMMControlTable	1.3.6.1.4.1.52.4.13.23.1		not-accessible	Table for WMM configuration per radio.
apWMMControlEntry	1.3.6.1.4.1.52.4.13.23.1.1		not-accessible	An Entry in the apWMMControlTable.
INT apWMMState	1.3.6.1.4.1.52.4.13.23.1.1.1	INTEGER	read-write	This value indicates the WMM state.
apWMMBssParamTable	1.3.6.1.4.1.52.4.13.23.2		not-accessible	Conceptual table for EDCA default parameter values at a non-AP QSTA. This table shall contain the four entries of the EDCA parameters corresponding to four possible ACs (access category): 1) AC_BE (best effort, ACI=0) 2) AC_BK (background, ACI=1) 3) AC_VI (video, ACI=2) 4) AC_VO (voice, ACI=3)
apWMMBssParamEntry	1.3.6.1.4.1.52.4.13.23.2.1		not-accessible	An Entry (conceptual row) in the apWMMBssParamTable. ifIndex - Each IEEE 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are indexed by ifIndex.
INT apWMMBssParamIndex	1.3.6.1.4.1.52.4.13.23.2.1.1	INTEGER	not-accessible	The index used to identify instances of the columnar objects in the apWMMBssParam Table. The value of this variable is 1) 1 AC_BE (best effort, ACI=0) 2) 2 AC_BK (background, ACI=1) 3) 3 AC_VI (video, ACI=2) 4) 4 AC_VO (voice, ACI=3)
INT apWMMBssParamCWmin	1.3.6.1.4.1.52.4.13.23.2.1.2	INTEGER	read-write	This attribute shall specify the value of the minimum size of the window in the exponent form that shall be used by a QSTA for a particular AC for generating a random number for the backoff.
INT apWMMBssParamCWmax	1.3.6.1.4.1.52.4.13.23.2.1.3	INTEGER	read-write	This attribute shall specify the value of the maximum size of the window in the exponent form that shall be used by a QSTA for a particular AC for generating a random number for the backoff.
INT apWMMBssParamAIFSN	1.3.6.1.4.1.52.4.13.23.2.1.4	INTEGER	read-write	This attribute shall specify the number of slots, after a SIFS duration, that the QSTA, for a particular AC, shall sense the medium idle either before transmitting or executing a backoff.
INT apWMMBssParamTXOPLimit	1.3.6.1.4.1.52.4.13.23.2.1.5	INTEGER	read-write	This attribute shall specify the maximum time of an TXOP in units of 32 microseconds for a given AC at a non-AP QSTA.
T/F apWMMBssParamAdmissionControl	1.3.6.1.4.1.52.4.13.23.2.1.6	TruthValue	read-write	This attribute, when TRUE, indicates that admission control is mandatory for the given AC. When False, this attribute indicates that the admission control is not mandatory for the given AC. The default value for this parameter shall be FALSE.
apWMMApParamTable	1.3.6.1.4.1.52.4.13.23.3		not-accessible	Conceptual table for EDCA default parameter values at the QAP. This table shall contain the four entries of the EDCA parameters corresponding to four possible ACs (access category): 1) AC_BE (best effort, ACI=0) 2) AC_BK (background, ACI=1) 3) AC_VI (video, ACI=2) 4) AC_VO (voice, ACI=3)
apWMMApParamEntry	1.3.6.1.4.1.52.4.13.23.3.1		not-accessible	An Entry (conceptual row) in the apWMMApParamTable. ifIndex - Each IEEE 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are indexed by ifIndex.
INT apWMMApParamIndex	1.3.6.1.4.1.52.4.13.23.3.1.1	INTEGER	not-accessible	The index used to identify instances of the columnar objects in the apWMMApParam Table. The value of this variable is 1) 1 AC_BE (best effort, ACI=0) 2) 2 AC_BK (background, ACI=1) 3) 3 AC_VI (video, ACI=2) 4) 4 AC_VO (voice, ACI=3)
INT apWMMApParamCWmin	1.3.6.1.4.1.52.4.13.23.3.1.2	INTEGER	read-write	This attribute shall specify the value of the minimum size of the window in the exponent form that shall be used by a QAP for a particular AC for generating a random number for the backoff.
INT apWMMApParamCWmax	1.3.6.1.4.1.52.4.13.23.3.1.3	INTEGER	read-write	This attribute shall specify the value of the maximum size of the window in the exponent form that shall be used by a QAP for a particular AC for generating a random number for the backoff.
INT apWMMApParamAIFSN	1.3.6.1.4.1.52.4.13.23.3.1.4	INTEGER	read-write	This attribute shall specify the number of slots, after a SIFS duration, that the QAP, for a particular AC, shall sense the medium idle either before transmitting or executing a backoff.
INT apWMMApParamTXOPLimit	1.3.6.1.4.1.52.4.13.23.3.1.5	INTEGER	read-write	This attribute shall specify the maximum time of an TXOP in units of 32 microseconds for a given AC at a QAP.
T/F apWMMApParamAdmissionControl	1.3.6.1.4.1.52.4.13.23.3.1.6	TruthValue	read-write	This attribute, when TRUE, indicates that admission control is mandatory for the given AC. When False, this attribute indicates that the admission control is not mandatory for the given AC. The default value for this parameter shall be FALSE.
apNotificationTrapTree	1.3.6.1.4.1.52.4.13.100
apNotificationObjects	1.3.6.1.4.1.52.4.13.100.1
MAC apNotificationDot11MacAddr	1.3.6.1.4.1.52.4.13.100.1.1	MacAddress	read-only	Mac Address of the affected interface, returned with traps only.
MAC apNotificationDot11Station	1.3.6.1.4.1.52.4.13.100.1.2	MacAddress	read-only	This attribute holds the MAC address of the wireless station
INT apNotificationDot11RequestType	1.3.6.1.4.1.52.4.13.100.1.3	INTEGER	read-only	This attribute defines the request type sent by the station. Value = 1: Unknown request type Value = 2: Association Request Value = 3: Re-association Request Value = 4: Authentication
INT apNotificationDot11ReasonCode	1.3.6.1.4.1.52.4.13.100.1.4	INTEGER	read-only	This attribute defines the reason for the failure of an operation. Value = 1: Invalid mode/state Value = 2: Station not authenticated. Value = 3: Internal error Value = 4: Out of sequence frame Value = 5: Un-supported algorithm Value = 6: Invalid frame length Value = 7: WEP is required on the AP Value = 8: WEP not allowed Value = 9: Challenge text mismatch
IP apNotificationDot11IpAddress	1.3.6.1.4.1.52.4.13.100.1.5	IpAddress	read-only	This value indicates the IP address of the Access Point
MAC apNotificationDot11AuthenticatorMacAddr	1.3.6.1.4.1.52.4.13.100.1.6	MacAddress	read-only	This attribute holds the MAC address of the authenticator for the AP.
apNotificationTrapObjects	1.3.6.1.4.1.52.4.13.100.2
NTF sysSystemUp	1.3.6.1.4.1.52.4.13.100.2.1			The system up notification shall be sent when the AP is fully up and running.
NTF sysSystemDown	1.3.6.1.4.1.52.4.13.100.2.2			The system down notification shall be sent before the AP is about to reboot.
NTF sysRadiusServerChanged	1.3.6.1.4.1.52.4.13.100.2.3			The RADIUS server changed notification shall be sent when the RADIUS server has changed from Primary / Secondary to Secondary / Primary.
NTF dot11StationAssociation	1.3.6.1.4.1.52.4.13.100.2.4			The associate notification shall be sent when a station successfully associates with the Access Point. The value of the notification shall include the MAC address of the station that has associated.
NTF dot11StationReAssociation	1.3.6.1.4.1.52.4.13.100.2.5			The re-associate notification shall be sent when a station successfully re-associates with the Access Point. The value of the notification shall include the MAC address of the station that has associated.
NTF dot11StationAuthentication	1.3.6.1.4.1.52.4.13.100.2.6			The authentication notification shall be sent when a station successfully authenticates with the Access Point. The value of the notification shall include the MAC address of the station that has authenticated.
NTF dot11StationRequestFail	1.3.6.1.4.1.52.4.13.100.2.7			The station request fail shall be sent out when a station fails to associate / re-associate / authenticate with the Access Point. The notification shall include the MAC address of the station and the reason code for the failure.
NTF dot1xMacAddrAuthSuccess	1.3.6.1.4.1.52.4.13.100.2.9			The 802.1X MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the RADIUS server. The value of the notification shall include the MAC address of the station that has authenticated.
NTF dot1xMacAddrAuthFail	1.3.6.1.4.1.52.4.13.100.2.10			The 802.1X MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the RADIUS server. The value of the notification shall include the MAC address of the station that failed to authenticate.
NTF dot1xAuthNotInitiated	1.3.6.1.4.1.52.4.13.100.2.11			The 802.1X authentication not initiated notification shall be sent when a station did not initiate 802.1X authentication with the RADIUS server. The value of the notification shall include the MAC address of the station that did not initiate 802.1X authentication.
NTF dot1xAuthSuccess	1.3.6.1.4.1.52.4.13.100.2.12			The 802.1X authentication success notification shall be sent when a station successfully authenticates with the RADIUS server. The value of the notification shall include the MAC address of the station that has authenticated.
NTF dot1xAuthFail	1.3.6.1.4.1.52.4.13.100.2.13			The 802.1X authentication failure notification shall be sent when a station fails to authenticate with the RADIUS server. The value of the notification shall include the MAC address of the station that failed to authenticate.
NTF localMacAddrAuthSuccess	1.3.6.1.4.1.52.4.13.100.2.14			The Local MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the database stored locally within the AP. The value of the notification shall include the MAC address of the station that has authenticated.
NTF localMacAddrAuthFail	1.3.6.1.4.1.52.4.13.100.2.15			The Local MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the database stored locally within the AP. The value of the notification shall include the MAC address of the station that has authenticated.
NTF pppLogonFail	1.3.6.1.4.1.52.4.13.100.2.16			The PPP Logon failure notification shall be sent out when the AP fails to login successfully to the PPP peer using the supplied username and password.
NTF iappStationRoamedFrom	1.3.6.1.4.1.52.4.13.100.2.17			The IAPP Station Roamed-From Notification shall be sent out whenever a station roams from another Access Point (AP) to this AP. The notification shall include the MAC address of the station and the IP address of the old AP.
NTF iappStationRoamedTo	1.3.6.1.4.1.52.4.13.100.2.18			The IAPP Station Roamed-To Notification shall be sent out whenever a station roams to another Access Point (AP) from this AP. The notification shall include the MAC address of the station and the IP address of the new AP.
NTF iappContextDataSent	1.3.6.1.4.1.52.4.13.100.2.19			The IAPP Context Data Sent notification shall be sent out whenever the context data for a station has been sent to the new AP with which the station has associated. The notification shall include the MAC address of the station and the IP address of the new AP.
NTF sntpServerFail	1.3.6.1.4.1.52.4.13.100.2.20			The sntpServerFail notification shall be sent when the AP fails to get time from the configured SNTP server.
NTF dot11InterfaceAFail	1.3.6.1.4.1.52.4.13.100.2.21			The InterfaceAFail notification shall be sent out when 802.11a wireless interface has failed.
NTF dot11InterfaceGFail	1.3.6.1.4.1.52.4.13.100.2.22			The InterfaceGFail notification shall be sent out when 802.11g wireless interface has failed.
NTF dot11WirelessSTPDetection	1.3.6.1.4.1.52.4.13.100.2.23			The WirelessSTPDetection notification shall be sent out when wireless STP packet has detected.

RFC description

Enterasys AP3000 wireless access point configuration for radio, security, VLAN, and authentication management.

Start monitoring Enterasys/Cabletron AP3000 wireless access point with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CTRON-AP3000-MIB