CTRON-IP-ROUTER-MIB

All MIBs › CTRON-IP-ROUTER-MIB

Category: Routing Protocols, Vendor: Cabletron/Enterasys

Description: Manages Cabletron IP routing configuration, routing tables, static routes, and IP protocol parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CTRON-IP-ROUTER-MIB?

CTRON-IP-ROUTER-MIB is a Cabletron Systems (now part of Enterasys/Extreme Networks) proprietary module for managing IP routing configuration and behavior on Cabletron routing devices, covering router-level identity, administrative/operational status, and IP forwarding statistics. It exposes both configuration and performance data: a router ID, system admin/operational status and reset controls, an operational-time (uptime-like) counter, IP MIB revision/version text, and separate forwarding-control objects with their own admin status, reset, operational time, and inbound packet counters. Its monitoring value spans both software/service status and traffic performance: administrators check nwIpSysOperStatus against nwIpSysAdminStatus to confirm the IP routing subsystem is actually running as configured, use nwIpSysOperationalTime as an uptime-style health indicator, and monitor nwIpFwdCtrInPkts for forwarding throughput or to detect a forwarding engine that has stopped counting packets. It builds on standard IP MIB (RFC 1213-style) conventions, as reflected in its IP-focused object naming and version text field. It is deployed on legacy Cabletron IP routers and Layer 3 switches in enterprise networks running Cabletron's networking equipment, and locating the CTRON-IP-ROUTER-MIB OID branch on the router is the starting point for polling these router ID, status, and forwarding-counter objects directly.

IPNetwork Monitor allows you to monitor SNMP objects defined in CTRON-IP-ROUTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cabletron Systems IP router/Layer 3 switch
legacy Cabletron/Enterasys routing platforms

Monitoring Examples

An administrator would compare nwIpSysAdminStatus to nwIpSysOperStatus to detect a router whose IP forwarding subsystem is administratively enabled but operationally down, and monitor nwIpSysOperationalTime for unexpected resets (a drop to a low value indicates a recent restart, possibly via nwIpSysAdminReset). Watching nwIpFwdCtrInPkts over time reveals whether the forwarding counter subsystem (nwIpFwdCtrAdminStatus/nwIpFwdCtrOperationalTime) is actively counting traffic; a counter that stops incrementing while admin status remains enabled points to a stalled forwarding engine needing a reset.

What Can Be Monitored

router ID and IP MIB version
system admin/operational status
system operational time (uptime)
forwarding counter admin/operational status
inbound forwarded packet counts

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks

From RFC1213-MIB

DisplayString
PhysAddress

From ROUTER-OIDS

nwRtrProtoSuites

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
nwIpAccessControl	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7
IP nwIpAclDestAddress	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.5	IpAddress	read-write	Specifies the destination IP address used to compare for matches on the access control list.
IP nwIpAclDestMask	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.6	IpAddress	read-write	Specifies the mask to be applied to the destination address to determine the portion of the address used to compare for matches on the access control list. Only bits that are matching are used in the comparison. This allows for wild-carding and partial matching.
nwIpAclEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1		not-accessible	Each entry contains IP source/destination access information.
INT nwIpAclIdentifier	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.1	INTEGER	read-only	This is the primary (major) index into the IP access control list table. This value identifies the access control list by a unique identifier arbitrarily assigned by the user. All entries that have the same value for nwIpAclIdentifier belong to the same access control list.
CTR nwIpAclMatches	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.4	Counter	read-only	Indicates the number of matches on this entry that have resulted in the permit/deny access restriction being applied as part of the forwarding process.
INT nwIpAclPermission	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.3	INTEGER	read-write	Specifies whether access is allowed or denied between the source and destination address pair. Note that source and destination are interchangeable when bi-directional control is selected. To remove an existing entry set nwIpAclPermission to invalid (2). Invalid entries disappear after reboot.
INT nwIpAclPortNumber	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.10	INTEGER	read-write	Specifies the port number used to compare for matches on the access control list. nwIpAclPortNumber only applies if nwIpAclProtocol is equal to 4 or 5, UDP or TCP nwIpAclPortNumber ranges from 0 to 65536. The value 0 is a wildcard which matches any port.
INT nwIpAclProtocol	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.9	INTEGER	read-write	Specifies the IP protocols checked to compare for matches on the access control list.
INT nwIpAclSequence	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.2	INTEGER	read-only	This is the secondary (minor) index into the IP access control list table. This number corresponds to a sequence number used to order multiple entries within the same access control list.
IP nwIpAclSrcAddress	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.7	IpAddress	read-write	Specifies the source address used to compare for matches on the access control list.
IP nwIpAclSrcMask	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.8	IpAddress	read-write	Specifies the mask to be applied to the source address to determine the portion of the address to be used to compare for matches on the access control list. Only bits that are matching are used in the comparison. This allows for wild-carding and partial matching.
nwIpAclTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2		not-accessible	This table contains the access control list information for IP traffic. This table contains entries, each of which allows packet forwarding between source/destination pairs to be permitted or denied. The list is identified by the Access Control List ID. Each list may contain multiple entries ordered by sequence number. When an access control list is searched, it is searched in sequence number order and the first match found ends the search. If no match is found, access defaults to permitted.
GAU nwIpAclValidEntries	1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.1	Gauge	read-only	Indicates the number of valid entries that exist in the access control list table.
nwIpAddrEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1		not-accessible	Each entry specifies the IP addressing information for the logical IP network for which the entry exists.
nwIpAddressTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2		not-accessible	This table contains an entry for each IP Address assigned to each router port.
IP nwIpAddrIfAddress	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.2	IpAddress	read-write	This is the IP Address assigned to the logical IP network for which the entry exist. As multiple IP Addresses may be assigned to a single router port, all addresses assigned to the port must be of the same subnet.
INT nwIpAddrIfAddrType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.4	INTEGER	read-write	Specifies whether the IP address, nwIpAddrIfAddress, is the primary, workgroup or secondary IP address for the IP router port for which the entry exists. A primary or workgroup address must be specified before a router port can be enabled.
INT nwIpAddrIfBcastAddr	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.6	INTEGER	read-write	Specifies the IP broadcast address type for the logical IP network for which the entry exists. A router port may be configured to send IP broadcasts using the all-ones-based format or the all-zeros-based format. nwIpAddrIfBcastAddr determines the value of the broadcast portion of the IP broadcast address being used to address broadcast packets.
INT nwIpAddrIfControl	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.3	INTEGER	read-write	Set this object to add or delete this entry from the table.
INT nwIpAddrIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.1	INTEGER	read-write	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
IP nwIpAddrIfMask	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.5	IpAddress	read-write	Specifies the Subnet Mask for the logical IP network for which the entry exists.
nwIpClientServices	1.3.6.1.4.1.52.4.2.2.2.3.1.2.12
nwIpComponents	1.3.6.1.4.1.52.4.2.2.2.3.1.2
nwIpDistanceVector	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1
nwIpEndSystems	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6
nwIpEvent	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10
INT nwIpEventAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.1.1	INTEGER	read-write	Sets the administrative state of IP event logging. enabled(3) causes the event log to become active. disabled(2) causes the event log to become inactive.
nwIpEventEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1		not-accessible	Each entry contains the information about an event that has been logged to the event table.
nwIpEventFilterEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1		not-accessible	Each entry describes an event filter which defines a particular type of event to be logged to the event log. The value of nwIpEventProtocol indicates the value used in either the nwRtgProtocolTable or the nwComponentTable in the Cabletron Routing Services MIB, which identifies the protocol to which the entry exists.
nwIpEventFilterTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1		not-accessible	This table contains an entry for each event filter configured for IP Routing Services events.
INT nwIpEventFltrAction	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.6	INTEGER	read-write	Specifies how the events are to be logged. Logging to the `log' stores the events in the event log table (nwIpEventFltrAction). Logging to `trap' sends events out through the trap mechanism.
INT nwIpEventFltrControl	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.3	INTEGER	read-write	Set this value to 3 to add the entry to the event filter table. Set this value to 2 to remove the entry from the event filter table.
INT nwIpEventFltrIfNum	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.2	INTEGER	read-only	Specifies the router port involved in the event for which the event filter exists.
INT nwIpEventFltrProtocol	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.1	INTEGER	read-only	Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentRtgInstance which identifies the protocol involved in the event for which the event filter exists.
INT nwIpEventFltrSeverity	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.5	INTEGER	read-write	Specifies the level of severity an event must meet in order to be logged. Controls the amount of event logging by ignoring events of a lower priority than specified by this filter value. `Highmed' ignores only events of the lowest severity. `Highlow' logs all events highest priority through lowest. `Highest' severity causes all events except those of the highest severity to be ignored. `Highmed' severity is the default setting which causes only events of the lowest severity to be ignored. `Highlow' severity logs all events, regardless of severity.
INT nwIpEventFltrType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.4	INTEGER	read-write	This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events are to be logged. Setting any bit to 0 removes an event type from this field and prevents that type of event from being logged.Setting any bit to 1 adds an event type to this field and enables that type of event to be logged.
INT nwIpEventIfNum	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.6	INTEGER	read-only	Indicates the router port that was involved in the event.
nwIpEventLogConfig	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.1
nwIpEventLogFilterTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2
nwIpEventLogTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3
INT nwIpEventMaxEntries	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.1.2	INTEGER	read-write	Sets the administrative state of IP event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive.
INT nwIpEventNumber	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.1	INTEGER	read-only	An ordinal value assigned to the event for which the log entry exists. nwIpEventNumber is assigned so that each event in the event log can be uniquely identified by the value of nwIpEventNumber.
INT nwIpEventProtocol	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.5	INTEGER	read-only	Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentInstance which indentifies the protocol or component that was involved in the event.
INT nwIpEventSeverity	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.4	INTEGER	read-only	Indicates the severity that was assigned to the event.
nwIpEventTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1		not-accessible	This table contains an entry for each event that has been logged.
OCT nwIpEventTextString	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.7	OCTET STRING	read-only	Contains the actual text string that was logged.
TIK nwIpEventTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.2	TimeTicks	read-only	Indicates the time at which the event was logged to the event log.
INT nwIpEventTraceAll	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.1.3	INTEGER	read-write	Enabled (3) allows logging of all event types on all router ports for all protocols and components. Disabled (2) causes the filter table to specify which events to log.
INT nwIpEventType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.3	INTEGER	read-only	Indicates the type of event that was logged.
nwIpFib	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5
nwIpFibSystem	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.1
nwIpFilters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.8
nwIpForwarding	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2
nwIpFwdCounters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1
CTR nwIpFwdCtrAddrErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.9	Counter	read-only	Indicates the total number of IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime, because of addressing errors in the IP header.
INT nwIpFwdCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.1	INTEGER	read-write	Sets the administrative state of the aggregate (system-wide) IP packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
CTR nwIpFwdCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.16	Counter	read-only	Indicates the total number of bytes in the IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.8	Counter	read-only	Indicates the total number of IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.15	Counter	read-only	Indicates the total number of bytes in the IP packets that have been administratively filtered, system-wide, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.7	Counter	read-only	Indicates the total number of IP packets that have been administratively filtered, system-wide, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrFwdBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.14	Counter	read-only	Indicates the total number of bytes in the IP packets that have been forwarded, system-wide, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrFwdPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.6	Counter	read-only	Indicates the total number of IP packets that have been forwarded, system-wide, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrHdrErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.11	Counter	read-only	Indicates the total number of IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime, because of an invalid IP header.
CTR nwIpFwdCtrHostDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.22	Counter	read-only	Indicates the total number of bytes in the IP packets that have been discarded by the local host, during nwIpFwdCtrOperationalTime, due to a lack of host resources.
CTR nwIpFwdCtrHostDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.19	Counter	read-only	Indicates the total number of IP packets that have been discarded by the local host, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrHostInBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.20	Counter	read-only	Indicates the total number of IP packets that have been received by the local host, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrHostInPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.17	Counter	read-only	Indicates the total number of IP packets that have been successfully delivered to the local host, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrHostOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.21	Counter	read-only	Indicates the total number of IP packets that have been transmitted by the local host, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrHostOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.18	Counter	read-only	Indicates the total number of IP packets that have been forwarded by the local host, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.12	Counter	read-only	Indicates the total number of bytes in the IP packets that have been received, system-wide, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.4	Counter	read-only	Indicates the total number of IP packets that have been received, system-wide, during nwIpFwdCtrOperationalTime.
CTR nwIpFwdCtrLenErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.10	Counter	read-only	Indicates the total number of IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime, because an invalid packet length is contained in the IP header.
TIK nwIpFwdCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.3	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwIpFwdCtrAdminStatus has been in the current state.
CTR nwIpFwdCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.13	Counter	read-only	Indicates the total number of bytes in the IP packets that have been transmitted, system-wide, during nwIpFwdOperationalTime.
CTR nwIpFwdCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.5	Counter	read-only	Indicates the total number of IP packets that have been transmitted, system-wide, during nwIpFwdCtrOperationalTime.
INT nwIpFwdCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.2	INTEGER	read-write	Resets the aggregate (system-wide) IP packet and byte counters. Reset (2) resets the IP aggregate counters to 0. nwIpFwdCtrOperationalTime is also reset to 0.
INT nwIpFwdIfAclIdentifier	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.9	INTEGER	read-write	Specifies the Access Control ID of the access control list in effect for the IP packets being routed on the router port for which the entry exists. A value of 0 indicates that no access control list is in effect.
INT nwIpFwdIfAclStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.10	INTEGER	read-write	Controls the operation of any access control list configured for IP traffic for the IP packets being routed on the router port for which the entry exists. Enabled (3) applies the access control list, indicated by nwIpFwdIfAclIdentifier to all IP traffic being routed on the port. Disabled (2) prevents the access control list from being applied.
INT nwIpFwdIfAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.2	INTEGER	read-write	Sets the administrative state of IP Routing Services on the router port for which the entry exists. Enabled (3) causes IP Routing Services to become active. Disabled (2) causes it to become inactive.
INT nwIpFwdIfCacheControl	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.11	INTEGER	read-write	Controls IP Address caching on the router port for which the entry exists. IP Address caching speeds-up the switching process. When IP Addresses caching is enabled, IP Addresses used for address validation, filtering, and forwarding are stored in the cache. This cache is checked first before doing a full route table lookup, which speeds up the switching process. Enabled (3) turns on IP Address caching. Disabled (2 turns it off.
CTR nwIpFwdIfCacheEntries	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.12	Counter	read-only	Indicates the number of entries in the IP Address cache on the router port for which the entry exists.
CTR nwIpFwdIfCacheHits	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.13	Counter	read-only	Indicates the number of times entries in the IP Address Cache have been used to provide the IP Address required to validate, filter, or forward an IP packet on the router port.
CTR nwIpFwdIfCacheMisses	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.14	Counter	read-only	Indicates the number of times the IP Address required to validate, filter, or forward an IP packet on the router port was not found in the IP Address cache.
nwIpFwdIfConfig	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1
INT nwIpFwdIfControl	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.5	INTEGER	read-write	This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
nwIpFwdIfCounters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2
CTR nwIpFwdIfCtrAddrErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.10	Counter	read-only	Indicates the total number of IP packets that have been discarded, because of addressing errors in the IP header, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
INT nwIpFwdIfCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.2	INTEGER	read-write	Sets the administrative state of the per-port IP packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
CTR nwIpFwdIfCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.17	Counter	read-only	Indicates the total number of bytes in the IP packets that have been discarded, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwIpFwdIfCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.9	Counter	read-only	Indicates the total number of IP packets that have been discarded (dropped), during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
nwIpFwdIfCtrEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1		not-accessible	Each entry indicates the packet and byte count of IP packets on the router port for which the entry exists.
CTR nwIpFwdIfCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.16	Counter	read-only	Indicates the total number of bytes in the IP packets that have been administratively filtered, during nwIpFwdIfCtrOperationalTime, on the IP router port for which the entry exists.
CTR nwIpFwdIfCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.8	Counter	read-only	Indicates the total number of IP packets that have been administratively filtered, during nwIpFwdIfCtrOperationalTime, on the IP router port for which this entry exists.
CTR nwIpFwdIfCtrFwdBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.15	Counter	read-only	Indicates the total number of bytes in the IP packets that have been forwarded, on the router port for which the entry exists, during nwIpFwdIfCtrOperationalTime.
CTR nwIpFwdIfCtrFwdPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.7	Counter	read-only	Indicates the total number of IP packets that have been forwarded during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwIpFwdIfCtrHdrErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.12	Counter	read-only	Indicates the total number of IP packets that have been discarded, because of an invalid IP header, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwIpFwdIfCtrHostDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.23	Counter	read-only	Indicates the total number of bytes in the IP packets that have been discarded by the local host due to a lack of host resources, that were received on the router port for which the entry exists, during nwIpFwdIfCtrOperationalTime.
CTR nwIpFwdIfCtrHostDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.20	Counter	read-only	Indicates the total number of IP packets discarded by the local host due to a lack of host resources, that were received on the router port for which the entry exists, during nwIpFwdIfCtrOperationalTime.
CTR nwIpFwdIfCtrHostInBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.21	Counter	read-only	Indicates the total number of bytes in the IP packets that have been successfully delivered to the local host, that were received on the router port for which the entry exists, during nwIpFwdIfCtrOperationalTime.
CTR nwIpFwdIfCtrHostInPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.18	Counter	read-only	Indicates the total number of IP packets that have been successfully delivered to the local host, that were received on the router port for which the entry exists, during nwIpFwdIfCtrOperationalTime.
CTR nwIpFwdIfCtrHostOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.22	Counter	read-only	Indicates the total number of bytes in the IP packets that have been transmitted by the local host, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwIpFwdIfCtrHostOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.19	Counter	read-only	Indicates the total number of IP packets that have been transmitted by the local host, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
INT nwIpFwdIfCtrIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
CTR nwIpFwdIfCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.13	Counter	read-only	Indicates the total number of bytes in the IP packets that have been received, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwIpFwdIfCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.5	Counter	read-only	Indicates the total number of IP packets that have been received, during nwIpFwdIfCtrOperationaltime, on the router port for which the entry exists.
CTR nwIpFwdIfCtrLenErrPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.11	Counter	read-only	Indicates the total number of IP packets that have been discarded, because an invalid packet length was contained in the IP header, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
TIK nwIpFwdIfCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that the per-port IP packet and byte counters have been active on the router port for which the entry exists.
CTR nwIpFwdIfCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.14	Counter	read-only	Indicates the total number of bytes in the IP packets that have been transmitted, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwIpFwdIfCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.6	Counter	read-only	Indicates the total number of IP packets that have been transmitted, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists.
INT nwIpFwdIfCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.3	INTEGER	read-write	Resets the per-port IP packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwIpFwdIfCtrOperationalTime is also reset to 0.
nwIpFwdIfCtrTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1		not-accessible	This table contains an entry for each router port configured and enabled for IP Routing Services.
nwIpFwdIfEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1		not-accessible	Each entry specifies the IP Routing Services configuration for the router port for which the entry exists.
INT nwIpFwdIfForwarding	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.7	INTEGER	read-write	Controls forwarding of IP packets on the router port for which the entry exists. Enabled (3) causes IP packets to be forwarded. Disabled (2) prevents IP packets from being forwarded.
INT nwIpFwdIfFrameType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.8	INTEGER	read-write	Specifies the framing type for IP packets forwarded on the router port for which the entry exists.
INT nwIpFwdIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port.
INT nwIpFwdIfMtu	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.6	INTEGER	read-write	Specifies the Maximum Transmission Unit (MTU) for IP packets on the router port for which the entry exists. This includes the IP header and data, but does not include framing.
TIK nwIpFwdIfOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwIpFwdIfOperStatus has been in its current state.
INT nwIpFwdIfOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.3	INTEGER	read-only	Indicates the current operating condition of IP Routing Services on the router port for which the entry exists. The value of nwIpFwdIfOperStatus indicates any problem with the configuration of IP routing Services on the router port. A value of 6 indicates that regardless of the value of nwIpFwdIfAdminStatus, IP Routing Services is not operating because of an invalid port-level configuration.
nwIpFwdIfTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1		not-accessible	This table contains an entry for each router port. This table is indexed by nwIpFwdIfIndex, which indicates the value of MIB 2 ifindex which identifies the router port for which each entry exists.
nwIpFwdInterfaces	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2
nwIpFwdSystem	1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1
INT nwIpHostCtlAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.2	INTEGER	read-write	This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol specific MIBS. Setting this object has no effect.
CTR nwIpHostCtlCacheHits	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.12	Counter	read-only	Indicates the number of times an entry in the cache has been used to successfully provide the physical address required to forward an IP packet on the router port for which the entry exists.
INT nwIpHostCtlCacheMax	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.8	INTEGER	read-write	Indicates the maximum number of entry slots the cache can consist of. nwIpHostCtlCacheMax cannot be set to less than 16. Setting this value does not allocate any memory for the cache.
CTR nwIpHostCtlCacheMisses	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.13	Counter	read-only	Indicates the number of times the physical address required to forward an IP packet has not been found in the cache on the router port for which the entry exists.
INT nwIpHostCtlCacheSize	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.9	INTEGER	read-only	Indicates the current number of entry slots in the cache. The cache automatically resizes to accommodate all entries up to the maximum number of entries set by nwIpHostCtlCacheMax.
nwIpHostCtlEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1		not-accessible	Each entry contains the control information for maintaining the cache on each router port.
INT nwIpHostCtlIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
CTR nwIpHostCtlNumDynamics	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.11	Counter	read-only	Indicates the number of dynamic entries in the cache on the router port for which the entry exists. Dynamic entries area added and aged out by the ARP protocol.
CTR nwIpHostCtlNumStatics	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.10	Counter	read-only	Indicates the total number of static entries in the cache on the router port for which the entry exists. Static entries remain in the cache until they are administratively removed.
TIK nwIpHostCtlOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwIpHostCtlOperStatus has been in the current state.
INT nwIpHostCtlOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.3	INTEGER	read-only	Indicates the current operating condition of the IP Host Address cache on the router port for which the entry exists.
INT nwIpHostCtlProtocol	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.5	INTEGER	read-write	Controls the operation of the ARP protocol on the router port for which the entry exists.
INT nwIpHostCtlProxy	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.7	INTEGER	read-write	Controls the operations of Proxy ARP on the router port for which the entry exists. Given the ARP protocol is enabled, nwIpHostCtlProtocol=3, setting nwIpHostCtlProxy to enabled (3) turns on Proxy ARP. When Proxy ARP is enabled on a router port, and an ARP request is received, requesting the address for an IP host whose network address is listed on the IP route table, then IP Routing Services sends a Proxy ARP response, with the physical address of the receiving router port in place of the requested host's physical address. Based on this proxy response, the requesting host will then forward packets to the router port, and IP Routing Services will then forward them to the correct destination.
INT nwIpHostCtlSnooping	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.6	INTEGER	read-write	Controls ARP Snooping on the router port for which the entry exists. Given the ARP protocol is enabled, nwIpHostCtlProtocol=3, setting nwIpHostCtlIfSnooping to enabled (3) turns on ARP Snooping. When ARP Snooping is enabled the source IP and physical addresses of all ARP packets received on the router port are added to the MIB 2 Net-to-Media Table.
nwIpHostCtlTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1		not-accessible	This table contains the control information for maintaining a cache of IP host addresses on each router port. Note that the of actual entries are maintained by the IP Address Translation Table (Net-to-Media) of MIB 2.
INT nwIpHostMapCircuitID	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.5	INTEGER	read-write	The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the IP Address at the end of the circuit. For non-WAN interfaces, the value of this object is zero.
nwIpHostMapEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1		not-accessible	Each entry contains one IpAddress to 'physical' address equivalence, including a circuit identifier if applicable. Also provided is the framing and port number required to converse with this host.
INT nwIpHostMapFraming	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.6	INTEGER	read-write	Specifies the framing type required to converse with the host for which this entry exists.
INT nwIpHostMapIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.1	INTEGER	read-only	This is the primary (major) index into the HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the IP router port for which the entry exists.
IP nwIpHostMapIpAddr	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.2	IpAddress	read-only	The IpAddress corresponding to the media-dependent 'physical' address and circuit identifier (if applic).
PHY nwIpHostMapPhysAddr	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.3	PhysAddress	read-write	The media-dependent 'physical' address. The value of this object is 0 for entries indicating native-wan(8) framing.
INT nwIpHostMapPortNumber	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.7	INTEGER	read-only	The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of interfaces in the system and the number of circuits present on interfaces which are of WAN type.
nwIpHostMapTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1		not-accessible	The Ip Address translation table used for mapping an IP address to physical address, framing, port and circuit identifier, if applicable.
INT nwIpHostMapType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.4	INTEGER	read-write	Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwIpHostMapTable. That is, it effectively dissasociates the circuit identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant nwIpHostMapType object.
nwIpHostsInterfaces	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2
CTR nwIpHostsRetryCount	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.1.2	Counter	read-only	Indicates the maximum number of times IP Routing Services will retry each attempt to resolve a host address.
nwIpHostsSystem	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.1
INT nwIpHostsTimeToLive	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.1.1	INTEGER	read-only	Indicates the amount of time (number of minutes) that an entry can remain in the ARP cache.
nwIpHostsToMedia	1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3
nwIpLinkState	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2
STR nwIpMibRevText	1.3.6.1.4.1.52.4.2.2.2.3.1.1.1	DisplayString	read-only	Indicates the current revision level of the IP MIB in textual format.
nwIpMibs	1.3.6.1.4.1.52.4.2.2.2.3.1.1
nwIpOspf	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1
INT nwIpOspfAdminReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.3	INTEGER	read-write	Resets OSPF. reset(2) will force a restart of OSPF on any active IP router ports, configured for OSPF, without a graceful shutdown, without affecting any other routing services.
INT nwIpOspfAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.1	INTEGER	read-write	Sets the administrative state of the OSPF routing protocol. enabled(3) causes OSPF to become active on any IP configured router ports. disabled(2) causes OSPF to perform a graceful shutdown on any active IP configured router ports.
nwIpOspfBgp4Table	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.4
nwIpOspfConfig	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1
nwIpOspfCounters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2
INT nwIpOspfCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.1	INTEGER	read-write	Sets the operating condition of the aggregate (device-wide) OSPF packet and byte counters. enable (3) causes these counters to become active on any router ports running OSPF. disabled (2) cause these counters to become inactive on any router port running OSPF.
CTR nwIpOspfCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.11	Counter	read-only	Indicates the total number of bytes in the OSPF packets that have been discarded, during nwIpOspfCtrOperationalTime.
CTR nwIpOspfCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.7	Counter	read-only	Indicates the total number of OSPF packets that have been discarded, device-wide, during nwIpOspfCtrOperationalTime.
CTR nwIpOspfCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.10	Counter	read-only	Indicates the total number of bytes in the OSPF packets that have been administratively filtered, device-wide, during nwIpOspfCtrOperationalTime.
CTR nwIpOspfCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.6	Counter	read-only	Indicates the total number of OSPF packets that have been administratively filtered, device-wide, during nwIpOspfCtrOperationalTime.
CTR nwIpOspfCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.8	Counter	read-only	Indicates the total number of bytes in the OSFP packets that have been received, device-wide, during nwIpOspfCtrOperationalTime.
CTR nwIpOspfCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.4	Counter	read-only	Indicates the total number of OSPF packets that have been received, device-wide, during nwIpOspfCtrOperationalTime.
TIK nwIpOspfCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.3	TimeTicks	read-only	Indicates the amount of time (# of time ticks) that the aggregate OSPF packet and byte counters have been active.
CTR nwIpOspfCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.9	Counter	read-only	Indicates the total number of bytes in the OSPF packets that have been transmitted, device-wide, during nwIpOspfCtrOperationalTime.
CTR nwIpOspfCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.5	Counter	read-only	Indicates the total number of OSPF packets that have been transmitted, device-wide, during nwIpOspfCtr- Operational-Time.
INT nwIpOspfCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.2	INTEGER	read-write	Resets the aggregate (device-wide) OSPF packet and byte counters. reset(2) resets the aggregate OSPF counters to 0 and nwIpOspfCtrOperationalTime to 0.
nwIpOspfDatabase	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.3
nwIpOspfDynamicTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.2
nwIpOspfFib	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2
nwIpOspfFibControl	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1
nwIpOspfFibEntries	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2
nwIpOspfFilters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.4
INT nwIpOspfForward	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1.1	INTEGER	read-only	The total number of valid Cabletron IP OSPF FIB entries to include static, dynamic, RIP and BGP4 type routes.
INT nwIpOspfIfAclIdentifier	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.8	INTEGER	read-write	Specifies the Access Control List ID of the access control list applied to OSPF traffic on the IP router port for which the entry exists. A value of 0 indicates that no Access List applies.
INT nwIpOspfIfAclStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.9	INTEGER	read-write	Controls the operation of the access list configured for OSPF traffic on the IP router port for which the entry exists. enabled(3) causes the access list to be applied. disabled(2) causes the access list not to be applied.
INT nwIpOspfIfAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.2	INTEGER	read-write	Sets the administrative state of OSPF on the IP router port for which the entry exists. enabled(3) causes OSPF to become active on the router port. disabled(2) causes OSPF to become inactive on the router port.
nwIpOspfIfConfig	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1
nwIpOspfIfCounters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2
INT nwIpOspfIfCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.2	INTEGER	read-write	Sets the administrative state of the OSPF packet and byte counters on the IP router port for which the entry exists. enabled(3) causes these counters to become active on the router port. disabled(2) turns these counters off.
CTR nwIpOspfIfCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.12	Counter	read-only	Indicates the total number of bytes in the OSPF packets that have been discarded, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime.
CTR nwIpOspfIfCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.8	Counter	read-only	Indicates the total number of OSPF packets that have been discarded, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime.
nwIpOspfIfCtrEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1		not-accessible	Each entry specifies the OSPF packet and byte counter for for the router for which the entry exists.
CTR nwIpOspfIfCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.11	Counter	read-only	Indicates the total number of bytes in the OSPF packets that have been administratively filtered, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime
CTR nwIpOspfIfCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.7	Counter	read-only	Indicates the total number of OSPF packets that have been administratively filtered, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime.
INT nwIpOspfIfCtrIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.1	INTEGER	read-only	This is the primary index into the OSPF interface counter table. This number corresponds to the index into the MIB-2 Interface Table which describes the router port for which the entry exists.
CTR nwIpOspfIfCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.9	Counter	read-only	Indicates the total number of bytes in the OSPF packets that have been received, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime.
CTR nwIpOspfIfCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.5	Counter	read-only	Indicates the total number of OSPF packets that have been received, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime.
TIK nwIpOspfIfCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.4	TimeTicks	read-only	Indicates the amount of time (# of time ticks) that the interface-specific OSPF packet and byte counters have been active on the router port for which the entry exists.
CTR nwIpOspfIfCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.10	Counter	read-only	Indicates the total number of bytes in the OSPF packets that have been transmitted, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime.
CTR nwIpOspfIfCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.6	Counter	read-only	Indicates the total number of OSPF packets that have been transmitted, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime.
INT nwIpOspfIfCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.3	INTEGER	read-write	Resets the OSPF packet and byte counters on the router port for which the entry exists. reset (2) resets the interface-specific counters to 0 and nwIpOspfIfCtrOperationalTime to 0.
nwIpOspfIfCtrTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1		not-accessible	This table contains the OSPF packet and byte counter for each configured OSPF router port.
nwIpOspfIfEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1		not-accessible	Each entry specifies the OSPF configuration information for the IP router port for which the entry exists.
INT nwIpOspfIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.1	INTEGER	read-only	This is the primary index into the OSPF interface table. This number corresponds to the index into the MIB-2 Interface Table which describes the router port for which the entry exists.
TIK nwIpOspfIfOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwIpOspfIfAdminStatus has been in its current state.
INT nwIpOspfIfOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.3	INTEGER	read-only	Sets the administrative state of OSPF on the IP router port for which the entry exists. enabled(3) causes OSPF to become active on the router port. disabled(2) causes OSPF to become inactive on the router port.
INT nwIpOspfIfSnooping	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.6	INTEGER	read-write	Controls the operation of OSPF Snooping on the IP router port for which the entry exists.OSPF Snooping is operating OSPF in passive mode, so it receives route information, builds and maintains a route information table, but does not advertise. enable (3) turns on OSPF Snooping. disable (2) turns it off.
nwIpOspfIfTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1		not-accessible	This table contains the OSPF configuration information for each IP router port
INT nwIpOspfIfType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.7	INTEGER	read-only	Specifies whether the attached network segment does or does not support broadcast media access. bma (2) indicates that route advertisements can be sent as broadcasts. nbma (3) indicates that route advertisements must be addresses directly to each neighbor.
INT nwIpOspfIfVersion	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.5	INTEGER	read-write	Indicates the OSPF protocol revision level supported on the router port.
nwIpOspfInterfaces	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2
INT nwIpOspfLeakAllBgp4Routes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1.4	INTEGER	read-write	Add all BGP4 routes in the IP FIB to the Cabletron IP OSPF FIB for advertisement in OSPF routing protocol announcements.
INT nwIpOspfLeakAllRipRoutes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1.3	INTEGER	read-write	Add all RIP routes in the IP FIB to the Cabletron IP OSPF FIB for advertisement in OSPF routing protocol announcements.
INT nwIpOspfLeakAllStaticRoutes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1.2	INTEGER	read-write	Add all static routes in the IP FIB to the Cabletron IP OSPF FIB for advertisement in OSPF routing protocol announcements.
TIK nwIpOspfOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.4	TimeTicks	read-only	Indicates the amount of time (#of time ticks) that OSPF has been in its current operational state.
INT nwIpOspfOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.2	INTEGER	read-only	Indicates the current operating condition of OSPF.
nwIpOspfRipTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.3
INT nwIpOSPFRoutePriority	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.1.2	INTEGER	read-write	Specifies the route priority assigned to routes learned by the OSPF routing protocol.
INT nwIpOspfStackSize	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.6	INTEGER	read-write	Specifies the stack size for the OSPF thread. In order for a change of this value to take effect, OSPF (nwIpOspfAdminStatus), IP (nwIpSysAdminStatus), or the device itself must be reset.
IP nwIpOspfStaticDest	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.1	IpAddress	read-only	The network Address of a static route leaked from the IP FIB into the Cabletron IP OSPF FIB.
nwIpOspfStaticEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1		not-accessible	A list of information for each static entry in the Cabletron IP OSPF FIB.
IP nwIpOspfStaticForwardMask	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.2	IpAddress	read-only	The network mask of a static route leaked from the IP FIB into the Cabletron IP OSPF FIB.
INT nwIpOspfStaticMetric	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.4	INTEGER	read-write	The Cabletron IP OSPF advertised cost of reaching the leaked static route.
INT nwIpOspfStaticMetricType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.5	INTEGER	read-write	The Cabletron IP OSPF metric type to be advertised using OSPF: Autonomous System External type 1 (1) or Autonomous System External type 2 (2).
IP nwIpOspfStaticNextHop	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.3	IpAddress	read-only	The next hop address of a static route leaked from the IP FIB into the Cabletron IP OSPF FIB. A value of 0.0.0.0 indicates that packets for the external destination should be forwarded to the advertising router.
INT nwIpOspfStaticStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.6	INTEGER	read-write	By setting this OID to inactive for a particular static route, the static route will be added to the IP OSPF FIB but not advertised. Setting this OID to active for a particular static route, the static route will be advertised by the OSPF router. By setting this OID to delete for a particular static route, the entry will no longer be advertised using OSPF and will be deleted from the IP OSPF FIB.
nwIpOspfStaticTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1		not-accessible	A table of statically configured entries in the Cabletron IP OSPF FIB.
nwIpOspfSystem	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1
INT nwIpOspfThreadPriority	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.7	INTEGER	read-write	Specifies the run-time execution priority of the OSPF protocol thread. In order for a change of this value to take effect, OSPF or the IP routing services, or the device must be reset.
STR nwIpOspfVersion	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.5	DisplayString	read-only	Indicates the current Cabletron revision level of OSPF in textual format, not the OSPF version supported.
IP nwIpRedirectAddress	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1.2	IpAddress	read-write	Sets the IP address to which the UDP broadcast packets matching the UDP redirect port value (nwIpRedirectPort) will be forwarded.
CTR nwIpRedirectCount	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1.4	Counter	read-only	Indicates how many UDP broadcast packets have been redirected, as specified by this entry.
nwIpRedirectEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1		not-accessible	Each entry contains the UDP port number of and IP Address to which UDP packets received as LAN broadcasts, should be redirected.
nwIpRedirector	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9
nwIpRedirectorInterface	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.2
nwIpRedirectorSystem	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1
INT nwIpRedirectPort	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1.1	INTEGER	read-only	This is the primary index into the UDP redirector table, identifying the UDP port number of the packets that will be redirected.
nwIpRedirectTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1		not-accessible	This table contains an entry for each UDP port configured for UDP broadcast redirection.
INT nwIpRedirectType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1.3	INTEGER	read-write	Set this object to enable or disable the redirector feature for the UDP port specified by nwIpRedirectAddress.
nwIpRip	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1
INT nwIpRipAdminReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.3	INTEGER	read-write	Resets the RIP routing protocol. Reset (2) forces a system-wide restart of the protocol system-wide without a graceful shutdown on any active router ports.
INT nwIpRipAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.1	INTEGER	read-write	Sets the administrative state of the RIP routing protocol system-wide. Enabled (3) causes RIP to become active on all router ports configured and enabled for IP Routing Services. Disabled (2) causes RIP to become inactive.
INT nwIpRipAgeOut	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.9	INTEGER	read-write	Specifies the amount of time, in seconds, that an inactive route table entry will be allowed to remain in the RIP route table before it is aged-out.
nwIpRipConfig	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1
nwIpRipCounters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2
INT nwIpRipCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.1	INTEGER	read-write	Sets the administrative state of the aggregate (system-wide) RIP routing protocol packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
CTR nwIpRipCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.11	Counter	read-only	Indicates the total number of bytes in the RIP packets that have been discarded, system-wide, during nwIpRipCtrOperationalTime.
CTR nwIpRipCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.7	Counter	read-only	Indicates the total number of RIP packets that have been discarded, system-wide, during nwIpRipCtrOperationalTime.
CTR nwIpRipCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.10	Counter	read-only	Indicates the total number of bytes in the RIP packets that have been administratively filtered, system-wide, during nwIpRipCtrOperationalTime.
CTR nwIpRipCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.6	Counter	read-only	Indicates the total number of RIP packets that have been administratively filtered, system-wide, during nwIpRipCtrOperationalTime.
CTR nwIpRipCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.8	Counter	read-only	Indicates the total number of bytes in the RIP packets that have been received, system-wide, during nwIpRipCtrOperationalTime.
CTR nwIpRipCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.4	Counter	read-only	Indicates the total number of RIP packets that have been received, system-wide, during nwIpRipCtrOperationalTime.
TIK nwIpRipCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.3	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwIpRipCtrAdminStatus has been in the current state.
CTR nwIpRipCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.9	Counter	read-only	Indicates the total number of bytes in the RIP packets that have been transmitted, system-wide, during nwIpRipCtrOperationalTime.
CTR nwIpRipCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.5	Counter	read-only	Indicates the total number of RIP packets that have been transmitted, system-wide, during nwIpRipCtrOperationalTime.
INT nwIpRipCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.2	INTEGER	read-write	Resets the aggregate (system-wide) RIP routing protocol packet and byte counters. Reset (2) resets the RIP aggregate counters to 0. nwIpRipCtrOperationalTime is also reset to 0.
nwIpRipDatabase	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3
INT nwIpRipDatabaseThreshold	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.8	INTEGER	read-write	Specifies the run-time maximum number of RIP entries that can be held in the RIP route table.
nwIpRipFilters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.4
INT nwIpRipHoldDown	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.10	INTEGER	read-write	Specifies the amount of time (in seconds) to wait before removing an entry from the route table, after receiving an update indicating that the destination has become unreachable. All routers exchanging RIP routing protocol information must have the same hold down time. The time must be long enough to allow all participating routers to receive the same update.
INT nwIpRipIfAclIdentifier	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.16	INTEGER	read-write	Specifies the Access Control ID of the access control list in effect for RIP routing protocol packets on the router port for which the entry exists. A value of 0 indicates that there is no access control list in effect for RIP routing protocol packets on the router port.
INT nwIpRipIfAclStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.17	INTEGER	read-write	Controls the operation of the access control list identified by nwIpRipIfAclIdentifier. Enabled (3) applies the access control list to all RIP routing protocol packet traffic on the router port for which the entry exists. Disabled (2) prevents the access control list from being applied.
INT nwIpRipIfAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.2	INTEGER	read-write	Sets the administrative state of the RIP routing protocol on the router port for which the entry exists. Enabled (3) causes RIP to become active on the router port. Disabled (2) causes RIP to become inactive on the router port.
INT nwIpRipIfAdvertisement	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.6	INTEGER	read-write	Sets the interval, in seconds, at which RIP advertises the RIP route table on the router port for which the entry exists.
nwIpRipIfConfig	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1
nwIpRipIfCounters	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2
INT nwIpRipIfCtrAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.2	INTEGER	read-write	Sets the administrative state of the RIP packet and byte counters on the router port for which this entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
CTR nwIpRipIfCtrDiscardBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.12	Counter	read-only	Indicates the total number of bytes in the RIP routing protocol packets that have been discarded during nwIpRipIfCtrOperationalTime, that were received on the router port for which the entry exists.
CTR nwIpRipIfCtrDiscardPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.8	Counter	read-only	Indicates the total number of RIP routing protocol packets that have been discarded, during nwIpRipIfCtrOperationalTime. that were received through the router port for which the entry exists.
nwIpRipIfCtrEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1		not-accessible	Each entry indicates the current packet and byte count of RIP routing protocol packets on the router port for which the entry exists.
CTR nwIpRipIfCtrFilteredBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.11	Counter	read-only	Indicates the total number of bytes in the RIP routing protocol packets that have been administratively filtered, during nwIpRipIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwIpRipIfCtrFilteredPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.7	Counter	read-only	Indicates the total number of RIP packets that have been administratively filtered during nwIpRipIfCtrOperationalTime, on the router port for which the entry exists.
INT nwIpRipIfCtrIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
CTR nwIpRipIfCtrInBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.9	Counter	read-only	Indicates the total number of bytes in the RIP routing protocol packets that have been received, during nwIpRipIfCtrOperationalTime, on the router port for which this entry exists.
CTR nwIpRipIfCtrInPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.5	Counter	read-only	Indicates the total number of RIP routing protocol packets that have been received, during nwIpRipIfCtrOperationalTime, on the router port for which the entry exists.
TIK nwIpRipIfCtrOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwIpRipIfCtrAdminStatus has been in the current state.
CTR nwIpRipIfCtrOutBytes	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.10	Counter	read-only	Indicates the total number of bytes in the RIP routing protocol packets that have been transmitted, during nwIpRipIfCtrOperationalTime, on the router port for which the entry exists.
CTR nwIpRipIfCtrOutPkts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.6	Counter	read-only	Indicates the total number of RIP packets that have been transmitted, during nwIpRipIfCtrOperationalTime, on the router port for which the entry exists.
INT nwIpRipIfCtrReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.3	INTEGER	read-write	Resets the per-port RIP packet and byte counters on the router port for which this entry exists. Reset (2) resets the counters to 0. nwIpRipIfCtrOperationalTime is also reset to 0.
nwIpRipIfCtrTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1		not-accessible	This table contains an entry for each router port.This table is indexed by nwIpRipIfCtrIfIndex which indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
nwIpRipIfEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1		not-accessible	Each entry contains the RIP routing protocol configuration for the router port for which the entry exists.
INT nwIpRipIfFloodDelay	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.7	INTEGER	read-write	Sets the length of time, in seconds, that the RIP routing protocol should wait after discovering that a directly connected route has gone down, before flooding updates (triggered updates) on the router port for which the entry exists. A value of 0 specifies that if a directly connected route goes down, updates should be sent immediately.
INT nwIpRipIfHelloTimer	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.10	INTEGER	read-write	This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interfaced to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
INT nwIpRipIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.1	INTEGER	read-only	Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
TIK nwIpRipIfOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, nwIpRipIfOperStatus, has been in its current state.
INT nwIpRipIfOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.3	INTEGER	read-only	Indicates the current operating condition of the RIP routing protocol on the router port for which the entry exists. The value of nwIpRipIfOperStatus indicates any problem with your RIP configuration on the router port. A value of 6 indicates that regardless of the value of nwIpRipIfAdminStatus, RIP is not operating on the port because of an invalid configuration.
INT nwIpRipIfPoisonReverse	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.12	INTEGER	read-write	Sets the operating condition of Poison Reverse on the router port for which the entry exists. When Poison Reverse is enabled, the RIP routing protocol advertises any downed route as unreachable during the period of time that it must wait before removing the route from the route table.
INT nwIpRipIfPriority	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.9	INTEGER	read-write	This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
INT nwIpRipIfRequestDelay	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.8	INTEGER	read-write	Sets the length of time, in hundredths of a second, that the RIP routing protocol should wait after receiving a route request packet, before sending a response on the router port for which the entry exists. A value of 0 specifies that if a route request packet is received on the port, a response should be sent immediately.
INT nwIpRipIfSnooping	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.13	INTEGER	read-write	Controls the operation of RIP Snooping on the router port. When RIP Snooping is enabled the RIP routing protocol operates in passive mode so that it receives route information, builds and maintains a route table, but does not advertise the route table or send updates on the router port for which the entry exists.
INT nwIpRipIfSplitHorizon	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.11	INTEGER	read-write	Sets the operating condition of Split Horizon on the router port for which the entry exists. When Split Horizon is enabled, the RIP routing protocol keeps track of which router port route information is received on, and prevents information about a route form being sent back out the same router port it was received on.
nwIpRipIfTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1		not-accessible	This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwIpRipIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
INT nwIpRipIfType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.14	INTEGER	read-only	Indicates whether the directly connected network segment does or does not support broadcast media access. If broadcast media access is supported, RIP advertisements are sent out one broadcast packet per router port. If broadcast media is not supported, RIP advertisements are sent directly to each neighbor router access.
INT nwIpRipIfVersion	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.5	INTEGER	read-write	Indicates the revision level of the RIP routing protocol firmware on the router port for which the entry exists, in textual format.
INT nwIpRipIfXmitCost	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.15	INTEGER	read-write	This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
nwIpRipInterfaces	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2
TIK nwIpRipOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwIpRipOperStatus, has been in its current state.
INT nwIpRipOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.2	INTEGER	read-only	Indicates the current operating condition of the RIP routing protocol system-wide. The value of nwIpRipOperStatus indicates any problem with your RIP configuration. A value of 6 indicates that regardless of the value of nwIpRipAdminStatus, RIP is not operating because of an invalid configuration.
nwIpRipRouteEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1		not-accessible	Each entry describes the RIP route to the destination network for which the entry exists.
INT nwIpRipRoutePriority	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.1.1	INTEGER	read-write	Specifies the route priority assigned to routes learned by the RIP routing protocol.
nwIpRipRouteTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1		not-accessible	This table contains the RIP route table. This table contains an entry for each route learned through the RIP routing protocol. Only the best routes from this table are added to the IP forwarding table to be used for packet switching.
TIK nwIpRipRtAge	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.6	TimeTicks	read-only	Indicates the amount of time, in seconds, since an update has been received for the route for which the entry exists.
INT nwIpRipRtFlags	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.8	INTEGER	read-only	Specifies properties of the RIP route. The bit mask is as follows: source-changed (1), best-source (2), local net (4), net-down (8), update-fib-only (16).
INT nwIpRipRtHops	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.5	INTEGER	read-only	Indicates the number of hops required to reach the destination for which the entry exists.
INT nwIpRipRtIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.2	INTEGER	read-only	This is a secondary index into IP-RIP route table. This number corresponds to the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
IP nwIpRipRtMask	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.4	IpAddress	read-only	Indicates the Subnet Mask of the IP Address for which the entry exists.
IP nwIpRipRtNetId	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.1	IpAddress	read-only	This is the primary index into the RIP route table. This number indicates the IP Address of the destination for which the entry exists.
IP nwIpRipRtSrcNode	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.3	IpAddress	read-only	This is a secondary index into the RIP route table. This number indicates the IP Address of the source router from which this route was learned. A value of 0.0.0.0 indicates that the source is on the network segment directly connected to the router port, nwIpRipRtIfIndex.
INT nwIpRipRtType	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.7	INTEGER	read-only	Indicates whether the destination network is directly connected through the router port specified by nwIpRipRtIfIndex, or is indirectly connected through another router, specified by nwIpRipRtSrcNode.
INT nwIpRipStackSize	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.6	INTEGER	read-write	Specifies the stack size of the RIP routing protocol thread. In order for a change of this value to take effect, the protocol (nwIpRipAdminReset), IP Routing Services (nwIpSysAdminReset), or the device running Routing Services must be reset.
nwIpRipSystem	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1
INT nwIpRipThreadPriority	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.7	INTEGER	read-write	Specifies the run-time execution priority of the RIP routing protocol thread. In order for a change of this value to take effect, RIP (nwIpRipAdminReset), IP Routing Services (nwIpAdminReset), or the device running Routing Services must be reset.
STR nwIpRipVersion	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.5	DisplayString	read-only	Indicates the current revision level of the RIP routing protocol firmware, in textual format.
nwIpRouter	1.3.6.1.4.1.52.4.2.2.2.3.1
INT nwIpStaticRoutePriority	1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.1.3	INTEGER	read-write	Specifies the route priority assigned to routes learned by statically configured routes..
nwIpSysAdministration	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2
INT nwIpSysAdminReset	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.3	INTEGER	read-write	Resets IP Routing Services, system-wide. Reset (2) forces a restart of IP Routing Services without a graceful shutdown on any active router ports, without affecting any other routing services.
INT nwIpSysAdminStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.1	INTEGER	read-write	Sets the administrative state of IP Routing Services system-wide. Enabled(3) causes IP Routing Services to become active on all router ports configured and enabled for IP Routing Services. Disabled(2) causes IP Routing Services to become inactive system-wide.
nwIpSysConfig	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.1
TIK nwIpSysOperationalTime	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.4	TimeTicks	read-only	Indicates the elapsed time, in hundredths of a second, that nwIpSysOperStatus has been in its current administrative state.
INT nwIpSysOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.2	INTEGER	read-only	Indicates the operating condition of IP Routing Services, system-wide. The value of nwIpSysOperStatus indicates any problem with your IP Routing Services configuration. A value of 6 indicates that regardless of the value of nwIpSysAdminStatus,IP Routing Services is not operating because of an invalid configuration.
IP nwIpSysRouterId	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.1.1	IpAddress	read-write	The IP Address used to uniquely identify the host (device) running IP Routing Services. The value of nwIpSysRouterId is equal to the highest IP Address in the IP Address Table.
nwIpSystem	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1
STR nwIpSysVersion	1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.5	DisplayString	read-only	Indicates the current revision level of the IP Routing Services firmware, in textual format.
nwIpTopology	1.3.6.1.4.1.52.4.2.2.2.3.1.2.4
nwIpWgDefEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1		not-accessible	Each entry specifies the configuration and status of an individual work group.
INT nwIpWgDefFastPath	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.5	INTEGER	read-write	Enabled (3) provides a fast path for packets through the router when both source and destination are within this workgroup - done mostly by skipping IP header validation.
IP nwIpWgDefHostAddress	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.2	IpAddress	read-write	The IP address of the IP router host which applies to every interface included in the workgroup.
INT nwIpWgDefIdentifier	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.1	INTEGER	read-only	An index into the definition table, unique to each entry, arbitrarily assigned by the user.
INT nwIpWgDefNumActiveIntf	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.8	INTEGER	read-only	The number of interfaces (ports) in this workgroup which have an operational status nwIpWgIfOperStatus of `OK' in the IP Work Group Interface table below.
INT nwIpWgDefNumTotalIntf	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.9	INTEGER	read-only	The number of interfaces (ports) in this workgroup which have an administrative status nwIpWgIfRowStatus of `active' in the IP Work Group Interface table below.
INT nwIpWgDefOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.7	INTEGER	read-only	The operational status of this workgroup definition entry. It will be `disabled' if this entry's row status is not active. It will be `subnetConflict' if there is a conflict with an existing active entry in this workgroup definition table.
INT nwIpWgDefRowStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.6	INTEGER	read-write	This status instance does not support `createAndGo.' A row entry should be created by a set of `createAndWait' which brings the status to `notReady.' The missing row info may then be supplied by setting nwIpWgDefHostAddr and nwIpWgDefSubnetMask. If defaults are OK for nwIpWgDefFastPath and nwIpWgDefSecurity this status instance may then be set to `active' to activate the row.
INT nwIpWgDefSecurity	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.4	INTEGER	read-write	A security level which applies to this workgroup as a whole. Security applies in conjunction with the range table below, which locks hosts to interfaces and/or physical address. Packets are filtered out if security is violated. For a high (4) security workgroup, a host must reside on the interface and with the physical address configured in a range table entry. For medium (3) security a host must reside on a configured interface, but unless a physical address is also specified in that range entry, the physical address is not constrained. For low (2) security a host is free to reside on any interface with any physical address if not configured in the range table, but if configured must match a configured entry. If security is none (1) the range table does not apply.
IP nwIpWgDefSubnetMask	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.3	IpAddress	read-write	The subnet mask for the IP address above, thereby defining the subnet which applies to every interface included in the workgroup.
nwIpWgDefTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1		not-accessible	This table has an entry for each workgroup subnet definition. It is indexed by and arbitrary integer indentifier.
INT nwIpWgHostDefIdent	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.3	INTEGER	read-only	The workgroup identifier. This corresponds to the primary index into the IP Work Group Interface Table.
nwIpWgHostEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1		not-accessible	Each entry shows a workgroup host. Entry is indexed by IP address and interface (port). It gives the workgroup and the physical address found for the host.
IP nwIpWgHostHostAddr	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.1	IpAddress	read-only	The host IP address. This is the primary index to the IP Work Group Host Table.
INT nwIpWgHostIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.2	INTEGER	read-only	The interface (port) number. This is the secondary index to the IP Work Group Host Table, matching the primary index to the MIB-2 IfTable which describes the router port.
OCT nwIpWgHostPhysAddr	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.4	OCTET STRING	read-only	The physical address of the host with the IP address given in the nwIpWgHostHostAddr for this conceptual row entry.
INT nwIpWgHostStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.5	INTEGER	read-only	This status of the host with respect to the workgroup. The host may be `unknown' if ARP has not discovered on which port it resides. The status of `invalid-multiple' means the same host IP address was later found duplicated on another port. The status of `invalid-physaddr' means the host matched an entry in the IP Work Group Range Table with respect to range and port, but did not match that entry for physical address. If the workgroup was high security this status would result even if no physical address was given in the range entry. The status of `invalid-range' could either mean that, in a high or medium security workgroup, the host was not in the range of any entry in the IP WORK GROUP Range Table, or that it was not in the range of an entry with a matching port. The status of `invalid-interface' could mean the port was physically down or just not in service in the IP Work Group Interface Table. The status of `invalid-workgroup' could mean the workgroup does not exist or is not in service in the IP Work Group Definition Table. The status of `invalid-expired' means the host became inactive and aged out on the port on which it was learned.
nwIpWgHostTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4		not-accessible	A read only status table for hosts in workgroups. It has the information similar to a net-to-media table.
INT nwIpWgIfDefIdent	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.1	INTEGER	read-only	The workgroup identifier. This is the primary index into the IP Work Group Interface Table, matching the index into the Definition Table above.
nwIpWgIfEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1		not-accessible	Each entry specifies the association of a router port to a defined workgroup.
INT nwIpWgIfIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.2	INTEGER	read-only	The interface number. This is the secondary index into the IP Work Group Interface Table, matching the primary index into the MIB-2 IfTable which describes the router port.
INT nwIpWgIfNumActiveHosts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.3	INTEGER	read-only	The number of hosts known to be active on this interface in this workgroup. These hosts are visible in the IP Work Group Host Table below. Hosts age out and become inactive in approximately 10 minutes if not rediscovered thrugh ARP.
CTR nwIpWgIfNumKnownHosts	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.4	Counter	read-only	The number of hosts seen on this interface in this workgroup since this interface entry was last activated.
INT nwIpWgIfOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.6	INTEGER	read-only	The operational status of this interface (port) entry. It will be `disabled' if this entry's row status is not active. It will be `workgroupInvalid' if either there is no workgroup defined for this entry's nwIpWgIfDefIdent or if the operational status for the workgroup in the definition table is not ok. It will be `addressConflict' if an entry in nwIpAddressTable is a conflict with the workgroup address of the definition. If there is no conflict and this entry's row status has just been activated, this operational status will be `resetRequired'. It will be `linkDown' if there are no physical connections on this interface and `routingDown' if routing or forwarding has been adminstratively disabled. If unspecified internal problems occur the status will be `internalError'.
INT nwIpWgIfRowStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.5	INTEGER	read-write	This status instance supports `createAndGo' semantics to create an active entry.
nwIpWgIfTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2		not-accessible	This table contains an entry for each port in a workgroup. It is indexed by the workgroup identifier and the MIB-II interface indentifier.
IP nwIpWgRngBegHostAddr	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.1	IpAddress	read-only	The beginning (lower) IP address of the address range. This is the primary index into the IP Work Group Range Table.
IP nwIpWgRngEndHostAddr	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.2	IpAddress	read-only	The ending (higher) IP address of the address range. This is the secondary index of the IP Work Group Range Table.
nwIpWgRngEntry	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1		not-accessible	Each entry configures a range of host IP addresses to be associated with a given interface ( port ). If the range consists of a single host address the entry may optionally specify a physical address. The entry is indexed by the range and the port. Ranges may not overlap. However a range may be duplicated on different ports. The address range must lie within the subnet defined for a given workgroup and thus the entry acquires the security level of that workgroup. If security is violated, packets to and from a given host IP address will be filtered out passing through the router. The source and destination IP packet addresses are checked against ranges in the range table during packet forwarding and must match as follows: For a high (4) security workgroup, a host must match a single host range entry - it must reside on the port with the physical address as configured in that entry. For a medium (3) security workgroup, a host must match a range entry in that it resides on that port, but unless a physical address is also specified in that entry, the physical address is not constrained. For a low (2) security workgroup, a host is free to reside on any port with any physical address as long as its IP address does not lie within the range of any entry in the range table, but if it does fall in a range then it must completely match that entry, or another entry with the duplicate range. Match completely means match the port and, if a physical address is specified, match that as well.
INT nwIpWgRngIfIndex	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.3	INTEGER	read-only	The interface number. This is the tertiary index into the IP Work Group Interface Table, matching the primary index into the MIB-2 IfTable which describes the router port.
INT nwIpWgRngOperStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.6	INTEGER	read-only	The operational status of this range table entry. It will be `disabled' if this entry's row status is not active. It will be `workgroupInvalid' if either there is no workgroup or if the operational status for the workgroup in the definition table associated with this address range is not ok. It will be `interfaceInvalid' if this interface is not in the workgroup interface table or if operational status of the interface entry is not ok. It will be `physAddrRequired' if the security level of the associated workgroup is high and no physical address has been specified for this entry.
OCT nwIpWgRngPhysAddr	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.4	OCTET STRING	read-write	The physical address of the host with the IP address given in the nwIpWgRngBegHostAddr for this conceptual row entry. Only single host range entry in which nwIpWgRngEndHostAddr is the same as nwIpWgRngBegHostAddr may set a physical address.
INT nwIpWgRngRowStatus	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.5	INTEGER	read-write	This status instance supports `createAndGo' semantics to create an active entry.
nwIpWgRngTable	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3		not-accessible	This table locks ranges of IP hosts (addresses) to ports. Entries in this table represent explicit permissions. The host(s) represented by a range entry may exchange packets with this router if it (they) match the port specified in the entry. Optionally physical address may be locked as well. This table functions in concert with the workgroup security level as defined in the IP Work Group Definition Table entry. For hosts not entered in this table the default for a low security workgroup is to permit packet exchange, whereas the default for medium and high security is to deny packet exchange.
nwIpWorkGroup	1.3.6.1.4.1.52.4.2.2.2.3.1.2.11

RFC description

Cabletron Systems IP routing services management and configuration objects.

Start monitoring Cabletron Systems IP router/Layer 3 switch (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CTRON-IP-ROUTER-MIB

What Is CTRON-IP-ROUTER-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description