CISCO-WIRELESS-IF-MIB

All MIBs › CISCO-WIRELESS-IF-MIB

Organization: Cisco Systems Inc.

Last Updated: 2006-01-04

Category: Vendor: Cisco Devices, Wireless and WLAN

Description: Manages Cisco 802.11 wireless interface parameters including radio configuration and association tables.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-WIRELESS-IF-MIB?

This MIB manages Cisco's proprietary 802.11 wireless point-to-point radio interfaces, extending the standard Interfaces MIB (IF-MIB) for the propWirelessP2P(157) interface type used by Cisco wireless bridge/radio hardware. It exposes radio-level configuration and status objects such as acquisition mode, privacy/encryption support, transmit/receive RF port indexing, antenna alignment, and self-test results. It is strongly hardware-status oriented, as administrators use self-test results to check radio diagnostic outcomes and acquisition mode/antenna alignment objects to verify a radio link has properly acquired its peer, which is essential for diagnosing degraded or failed wireless point-to-point links. It explicitly relates to and extends the standard IF-MIB, with each wireless interface represented via ifEntry and appearing in ifStackTable entries. It is deployed on Cisco fixed wireless bridge/radio equipment used for point-to-point wireless links, such as building-to-building connectivity. Engineers can download the CISCO-WIRELESS-IF-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-WIRELESS-IF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco wireless point-to-point radio/bridge equipment

Monitoring Examples

An administrator troubleshooting a degraded wireless bridge link would check cwrRadioBaseTable / cwrRadioBaseEntry for cwrSelfTest results and cwrAcquisitionMode to confirm the radio has successfully acquired its remote peer. The cwrAntAlignment object would be checked during installation or after a suspected physical disturbance to verify antenna alignment is still within tolerance. cwrTxRfIndex, cwrRx1RfIndex, and cwrRx2RfIndex identify which RF ports are active for transmit and diversity receive, useful for confirming correct radio port configuration.

What Can Be Monitored

radio self-test/diagnostic results
acquisition mode / peer link acquisition state
antenna alignment status
TX/RX RF port configuration
privacy/encryption support setting

Imported Objects

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From CISCO-WIRELESS-TC-MIB

CwrCollectionAction
CwrCollectionStatus
CwrCwConsecutiveSevErrSecond
CwrCwDegradedMinute
CwrCwDegradedSecond
CwrCwErrorFreeSecond
CwrCwErroredSecond
CwrCwSeverelyErroredSecond
CwrOscState
CwrRFZeroIndex
CwrRadioSignalAttribute
CwrThreshLimitType
WirelessGauge64

From IF-MIB

ifIndex

OBJECT-TYPE

From RMON-MIB

OwnerString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TimeInterval
TruthValue

How to Use in IPNetwork Monitor

Example using cwrArq1ByteErrs OID:

Select a Cisco wireless point-to-point radio/bridge equipment (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cwrArq1ByteErrs into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object identifies the number of 1 byte errors that were corrected since the the radio link reached linkOperational state. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ciscoWirelessIfMIB	1.3.6.1.4.1.9.9.136			This is the MIB Module for the Cisco Wireless Radio Point to Point interface specification. I) Relationship of the Cisco Wireless Radio IF MIB to Interfaces MIB: One instance of the ifEntry exists for each wireless interface. The ifType of each such interface will be propWirelessP2P(157). If (at least) one IP address is active on an interface with this ifType without the use of any intervening (multiplexing) sub-layer, then it will appear in exactly two ifStackTable entries: i.e., for an ifType=propWirelessP2P(157) interface with ifIndex 'x', the ifStackTable will contain: ifStackStatus.0.x=active ifStackStatus.x.0=active The ifTestTable and ifRcvAddressTable are not supported by this ifType. II) ifEntry for the Wireless MAC Layer: The ifEntry for the wireless MAC Layer supports the following groups in the Interfaces MIB : a. ifGeneralInformationGroup b. ifHCPacketGroup For all those objects where the behavior is as defined in the Interfaces MIB, refer to Interfaces MIB for description. Special conditions or exceptions are explicitly documented here. IfTable Attribute Comments ================= =============================================== ifType, The IANA value of propWirelessP2P(157). ifMtu, Return 1500. ifSpeed, Current configured bandwidth. It can be 1.5Mbits/sec to 12Mbits/sec. ifPhysAddress, Return 0 length octet string. ifAdminStatus, The administrative status of this interface. ifOperStatus, The current operational status of the wireless MAC layer interface. ifLastChange, Refer to the Interfaces MIB. ifInMulticastPkts, Returns 0. ifInBroadcastPkts, Returns 0. ifOutMulticastPkts, Returns 0. ifOutBroadcastPkts, Returns 0. ifHCInMulticastPkts, Not supported. ifHCInBroadcastPkts, Not supported. ifHCOutMulticastPkts, Not supported. ifHCOutBroadcastPkts, Not supported. Glossary The following terms are used in the MIB definitions below. Radio Interface: The interface that provides the wireless communication features. Radio Link: The bi-directional wireless link that exists between two communicating radio. Radio PHY: Represents the transmission characteristics of the Radio Link. RF Unit: The Radio Frequency components and the associated antennas. ARQ: Automatic Repeat Query. Cisco Wireless MIB Organization The Cisco Wireless Radio IF MIB provides the following management groups : o. Radio Base Group This group contains common information about a radio interface . It provides facilities to configure attributes such as self-test, acquisition mode, etc. It includes configuration information used to set up a radio link. o. Radio PHY Quality Group This group provides facilities to control/tune the transmission and reception quality of the Radio Link. The quality of the Radio Link is measured using the metrics defined in radio Radio Link metrics group. o. Radio Frequency Resource Group This contains information about the Radio frequency transmission and reception resources available on the system. This group determines the portions of the radio spectrum at which the radio subsystem can operate. This group in conjunction with the radio PHY group determine the acutal spectrum that gets used for communications. o. Radio Link Metrics Group This group contains metrics to measure the quality of radio Link. This includes metrics such as total received codeword errors, resync count, errored seconds etc. o. Radio Signal Group This group contains information about the radio signal(s) that were received or attributes of the radio signals computed from received signals. This group models the real-time data that is collected. The key characteristics are: 1. The amount of information captured in these parameters is large and cannot be modeled as single values. 2. They represent real-time information, which cannot be polled for as well. 3. Hardware captures this information. All the radio signal characteristics are modeled in three ways: 1. Histogram 2. Timelines 3. Snapshots For management purposes radio signal characteristics are made accessible via: 1. History Group 2. Timeline Group 3. Snapshot Group These groups are described below. o. History Group This group contains information about the radio system characteristics which are inherently modeled as historgrams. Certain characteristics of the radio system may be captured as histograms by the hardware. The user may configure these histograms as needed. It exists for the following reasons: 1. The amount of information contained in these parameters is large and cannot be modeled as single values. 2. They represent real-time information, which cannot be polled for as well. 3. Key signal processing information cannot be captured by normal SNMP (say 1 sec poll interval) monitoring. 4. Hardware captures this information as histograms. 5. In wireless environments this is key information that can be captured for fault and performance management. o. Timeline Group This group contains information about how raw radio signal characteristics that may be captured. Timelines are normally associated with a threshold defined in the threshold group. o. Threshold Group This provides provides facilities to define thresholds on the raw signal attributes that are processed by the hardware. Normally thresholds are used in conjunction with Timelines to capture specific radio signal behavior. o. Snapshot Group This group provides facilities that may be used to capture multiple radio signal attributes keyed to a single user initiated trigger. Simultaneous capture of multiple real-time attributes keyed to a single trigger provides indepth information about the behavior of the system. o. Test Group This provides facilities to establish loopback at various points in the hardware for diagnostic purposes. o. Antenna Group This group provides information about the antenna resources installed and available for use. o. Trap Group It provides the list of traps that the wireless system will generate.
CWR cwr1HrConsecSvErrSeconds	1.3.6.1.4.1.9.9.136.1.6.4.1.6	CwrCwConsecutiveSevErrSecond	read-only	This object represents the cumulative Codeword Consecutive Severely Errored Seconds (CSES) detected since link power up, captured at cwr1HrUpdateTime.
CWR cwr1HrDegradedMinutes	1.3.6.1.4.1.9.9.136.1.6.4.1.7	CwrCwDegradedMinute	read-only	This object represents the cumulative Codeword Degraded Minutes detected since link power up, captured at cwr1HrUpdateTime.
NUM cwr1HrErroredCodewords	1.3.6.1.4.1.9.9.136.1.6.4.1.8	WirelessGauge64	read-only	This object represents the cumulative errored codewords detected since link power up, captured at cwr1HrUpdateTime.
CWR cwr1HrErroredSeconds	1.3.6.1.4.1.9.9.136.1.6.4.1.4	CwrCwErroredSecond	read-only	This object represents the cumulative Codeword Errored Seconds (ES) detected since link power up, captured at cwr1HrUpdateTime.
CWR cwr1HrErrorFreeSeconds	1.3.6.1.4.1.9.9.136.1.6.4.1.3	CwrCwErrorFreeSecond	read-only	This object represents the cumulative Codeword Error Free Seconds (EFS) detected since link power up, captured at cwr1HrUpdateTime.
cwr1HrMetricsEntry	1.3.6.1.4.1.9.9.136.1.6.4.1		not-accessible	This represents one entry in the cwr1HrMetricsTable indexed by ifIndex and cwr1HrMetricsIndex. The first entry in the table (cwr1HrMetricsIndex = 1) represents the chronologically oldest data available.
I32 cwr1HrMetricsIndex	1.3.6.1.4.1.9.9.136.1.6.4.1.1	Integer32	not-accessible	Each entry represents the sum of the metrics from the previous 1 hour entry + the 1 hour period immdeiately prior to the most recent update.
cwr1HrMetricsTable	1.3.6.1.4.1.9.9.136.1.6.4		not-accessible	This table contains metrics collected over the duration of one hour. This table will have a maximum of 24 entries providing cumulative status of the link, identified by ifIndex, over the past 24 hours. This table is updated once every hour.
CWR cwr1HrSevErroredSeconds	1.3.6.1.4.1.9.9.136.1.6.4.1.5	CwrCwSeverelyErroredSecond	read-only	This object represents the cumulative Codeword Severely Errored Seconds (SES) detected since link power up, captured at cwr1HrUpdateTime.
NUM cwr1HrTotalCodewords	1.3.6.1.4.1.9.9.136.1.6.4.1.9	WirelessGauge64	read-only	This object represents the cumulative total received codewords detected since link power up, captured at cwr1HrUpdateTime.
I32 cwr1HrUpdateTime	1.3.6.1.4.1.9.9.136.1.6.4.1.2	Integer32	read-only	This object represents time in seconds since system power up at which time this entry was updated.
NUM cwr1MinCodewords	1.3.6.1.4.1.9.9.136.1.6.5.1.9	WirelessGauge64	read-only	This object represents the cumulative total received codewords detected since link power up, captured at cwr1MinUpdateTime.
CWR cwr1MinConsecSvCwErrSeconds	1.3.6.1.4.1.9.9.136.1.6.5.1.6	CwrCwConsecutiveSevErrSecond	read-only	This object represents the cumulative Codeword Consecutively Severely Errored Seconds (CSES) detected since link power up, captured at cwr1MinUpdateTime.
CWR cwr1MinDegradedSeconds	1.3.6.1.4.1.9.9.136.1.6.5.1.7	CwrCwDegradedSecond	read-only	This object represents the cumulative Codeword Degraded Seconds (DS) detected since link power up, captured at cwr1MinUpdateTime.
NUM cwr1MinErroredCodewords	1.3.6.1.4.1.9.9.136.1.6.5.1.8	WirelessGauge64	read-only	This object represents the cumulative errored codewords detected since link power up, captured at cwr1MinUpdateTime.
CWR cwr1MinErroredSeconds	1.3.6.1.4.1.9.9.136.1.6.5.1.4	CwrCwErroredSecond	read-only	This object represents the cumulative Codeword Errored Seconds (ES) detected since link power up, captured at cwr1MinUpdateTime.
CWR cwr1MinErrorFreeSeconds	1.3.6.1.4.1.9.9.136.1.6.5.1.3	CwrCwErrorFreeSecond	read-only	This object represents the cumulative Codeword Error Free Seconds (EFS) detected since link power up, captured at cwr1MinUpdateTime.
cwr1MinMetricsEntry	1.3.6.1.4.1.9.9.136.1.6.5.1		not-accessible	This represents one entry in the cwr1MinMetricsTable indexed by ifIndex and cwr1MinMetricsIndex. The first entry in the table (cwr1MinMetricsIndex = 1) represents the chronologically oldest data available.
I32 cwr1MinMetricsIndex	1.3.6.1.4.1.9.9.136.1.6.5.1.1	Integer32	not-accessible	Each entry represents the sum of the metrics from the previous 1 minute entry + the 1 minute period immdeiately prior to the most recent update.
cwr1MinMetricsTable	1.3.6.1.4.1.9.9.136.1.6.5		not-accessible	This table contains metrics collected over the duration of one minute. This table will have a maximum of 60 entries providing cumulative status of the link, identified by ifIndex, over the past 60 minutes. This table is updated once every minute.
CWR cwr1MinSevErroredSeconds	1.3.6.1.4.1.9.9.136.1.6.5.1.5	CwrCwSeverelyErroredSecond	read-only	This object represents the cumulative Codeword Severely Errored Seconds (SES) detected since link power up, captured at cwr1MinUpdateTime.
I32 cwr1MinUpdateTime	1.3.6.1.4.1.9.9.136.1.6.5.1.2	Integer32	read-only	This object represents time in seconds since system power up at which time this entry was updated.
G32 cwr1SecArqCodewordErrors	1.3.6.1.4.1.9.9.136.1.6.6.1.5	Gauge32	read-only	This object represents the cumulative number of uncorrectable codewords consumed by the Automatic Repeat Query error correction engine at the time this entry was updated. This is also called as Post ARQ codeword error.
G32 cwr1SecConsecutiveCwErrs	1.3.6.1.4.1.9.9.136.1.6.6.1.11	Gauge32	read-only	This object represents the size of the larget block of consecutive codeword errors received since this entry was last updated.
G32 cwr1SecCorrectedSyncByteErrs	1.3.6.1.4.1.9.9.136.1.6.6.1.10	Gauge32	read-only	This object represents the cumulative number of corrected sync byte errors, at the time this entry was updated.
I32 cwr1SecIndex	1.3.6.1.4.1.9.9.136.1.6.6.1.1	Integer32	not-accessible	Each entry represents the sum of the metrics from the previous 1 second entry + the 1 second period immdeiately prior to the most recent update.
cwr1SecMetricsEntry	1.3.6.1.4.1.9.9.136.1.6.6.1		not-accessible	This represents one entry in the cwr1SecMetricsTable indexed by ifIndex and cwr1SecMetricsIndex. The first entry in the table (cwr1SecIndex = 1) represents the chronologically oldest data available.
cwr1SecMetricsTable	1.3.6.1.4.1.9.9.136.1.6.6		not-accessible	This table contains metrics collected over a duration of 1 second. The data in this table is derived directly from the hardware. This table will have a maximum of 60 entries providing cumulative status of the link, identified by ifIndex, over the past 60 seconds. This table is updated once every second.
NUM cwr1SecPostARQGoodCodewords	1.3.6.1.4.1.9.9.136.1.6.6.1.12	WirelessGauge64	read-only	This object represents the cumulative number of error free codewords emitted by the Automatic Repeat Query error correction engine at the time this entry was updated. Also called as Post ARQ good codewords.
NUM cwr1SecRSCodewordErrors	1.3.6.1.4.1.9.9.136.1.6.6.1.4	WirelessGauge64	read-only	This object represents the cumulative uncorrectable codewords emitted by the Reed-Solomon error correction engine at the time this entry was updated. This is also called Pre ARQ codeword error.
NUM cwr1SecRxCodewords	1.3.6.1.4.1.9.9.136.1.6.6.1.3	WirelessGauge64	read-only	This object represents the cumulative total number of codewords received by this radio link at the time this entry was updated.
G32 cwr1SecRxRrCount	1.3.6.1.4.1.9.9.136.1.6.6.1.6	Gauge32	read-only	This represents the cumulative number of unique RR's (Retransmit Requests) received (from the remote end) at the time this entry was updated. The remote end issues a Retransmit Request if it receives an uncorrectable codeword.
G32 cwr1SecRxRrEventCount	1.3.6.1.4.1.9.9.136.1.6.6.1.7	Gauge32	read-only	This object represents the cumulative number of RRs (Retransmit Requests) that were serviced at the time this entry was updated.
G32 cwr1SecTxArqCount	1.3.6.1.4.1.9.9.136.1.6.6.1.8	Gauge32	read-only	This object represents cumulative number of unique ARQ's that were received by the transmit side of the local end at the time this entry was updated. This provides an indication of how error free the transmisisons of the local end of the link are from the the remote end's perspective.
G32 cwr1SecTxArqEventCount	1.3.6.1.4.1.9.9.136.1.6.6.1.9	Gauge32	read-only	This object represents cumulative number of ARQ's that were serviced at the time this entry was updated. A serviced ARQ results in a re-transmitted codeword.
I32 cwr1SecUpdateTime	1.3.6.1.4.1.9.9.136.1.6.6.1.2	Integer32	read-only	This object represents time in seconds since system power up at which time this entry was updated.
CWR cwr24HrConsecSvErrSeconds	1.3.6.1.4.1.9.9.136.1.6.3.1.6	CwrCwConsecutiveSevErrSecond	read-only	This object represents the number of Codeword Consecutively Severely Error Seconds (CSES) detected since link power up, captured at cwr24HrUpdateTime.
CWR cwr24HrDegradedMinutes	1.3.6.1.4.1.9.9.136.1.6.3.1.7	CwrCwDegradedMinute	read-only	This object represents the number of Codeword Degraded Minutes (DM) detected since link power up, captured at cwr24HrUpdateTime.
CWR cwr24HrErroredSeconds	1.3.6.1.4.1.9.9.136.1.6.3.1.4	CwrCwErroredSecond	read-only	This object represents the number of Codeword Error Seconds (ES) detected since link power up, captured at cwr24HrUpdateTime.
CWR cwr24HrErrorFreeSeconds	1.3.6.1.4.1.9.9.136.1.6.3.1.3	CwrCwErrorFreeSecond	read-only	This object represents the cumulative Codeword Error Free Seconds (EFS) detected since link power up, captured at cwr24HrUpdateTime.
cwr24HrMetricsEntry	1.3.6.1.4.1.9.9.136.1.6.3.1		not-accessible	This represents one entry in the cwr24HrMetricsTable indexed by ifIndex and cwr24HrMetricsIndex. The first entry in the table (cwr24HrMetricsIndex = 1) represents the chronologically oldest data available.
I32 cwr24HrMetricsIndex	1.3.6.1.4.1.9.9.136.1.6.3.1.1	Integer32	not-accessible	Each entry represents the sum of the metrics from the previous 24 hour entry + the 24 hour period immdeiately prior to the most recent update.
cwr24HrMetricsTable	1.3.6.1.4.1.9.9.136.1.6.3		not-accessible	This table contains metrics collected over the duration of 24 hours. This table is updated once every day for 32 days. Therefore, this table will have a maximum of 32 entries that provide cumulative status of the link, identified by ifIndex.
CWR cwr24HrSevErroredSeconds	1.3.6.1.4.1.9.9.136.1.6.3.1.5	CwrCwSeverelyErroredSecond	read-only	This object represents the number of Codeword Severely Error Seconds (SES) detected since link power up, captured at cwr24HrUpdateTime.
NUM cwr24HrTotalCodewords	1.3.6.1.4.1.9.9.136.1.6.3.1.9	WirelessGauge64	read-only	This object represents the total number of codewords received on this link since link power up, captured at cwr24HrUpdateTime.
NUM cwr24HrTotalErroredCodewords	1.3.6.1.4.1.9.9.136.1.6.3.1.8	WirelessGauge64	read-only	This object represents the total number of errored codewords detected since link power up, captured at cwr24HrUpdateTime.
I32 cwr24HrUpdateTime	1.3.6.1.4.1.9.9.136.1.6.3.1.2	Integer32	read-only	This object represents time in seconds since system power up at which time this entry was updated.
INT cwrAcquisitionMode	1.3.6.1.4.1.9.9.136.1.3.1.1.2	INTEGER	read-write	This object specifies whether the radio should act as the master or as the slave. The slave radio tracks the master's frequency.
T/F cwrAntAlignment	1.3.6.1.4.1.9.9.136.1.3.1.1.9	TruthValue	read-write	For normal operation this should be set to false(2). If it set true(1), then the radio link is placed in antenna alignment mode. In this mode control signals are sent to the RF resource which enables the operator to monitor the signal received strength at the RF resource. This is mainly used for antenna steering i.e. positioning the antenna for the best possible signal reception. If set to true(1), the radio link's response to rapid changes in signal strength may potentially be affected.
STR cwrAntennaDescr	1.3.6.1.4.1.9.9.136.1.10.1.1.5	DisplayString	read-write	This object describes the antenna.
cwrAntennaEntry	1.3.6.1.4.1.9.9.136.1.10.1.1		not-accessible	This represents one entry in the cwrAntennaTable. This table provides details on the antennas available for use on the local system. It is indexed by cwrAntennaIndex.
I32 cwrAntennaGain	1.3.6.1.4.1.9.9.136.1.10.1.1.6	Integer32	read-write	This object represents the gain of this antenna.
I32 cwrAntennaIndex	1.3.6.1.4.1.9.9.136.1.10.1.1.1	Integer32	not-accessible	This object represents the index of this entry in the cwrAntennaTable.
INT cwrAntennaPolarization	1.3.6.1.4.1.9.9.136.1.10.1.1.7	INTEGER	read-write	This object represents the electrirc polarization of the antanna.
cwrAntennaTable	1.3.6.1.4.1.9.9.136.1.10.1		not-accessible	This table contains information about the antenns available for use.
STR cwrAntennaType	1.3.6.1.4.1.9.9.136.1.10.1.1.4	DisplayString	read-write	This object represents antenna type for example 'dish-antenna'.
I32 cwrAntennaXDim	1.3.6.1.4.1.9.9.136.1.10.1.1.2	Integer32	read-write	This object represents the dimension of the antenna in the X direction.
I32 cwrAntennaYDim	1.3.6.1.4.1.9.9.136.1.10.1.1.3	Integer32	read-write	This object represents the dimension of the antenna in the Y direction.
C64 cwrArq1ByteErrsEx	1.3.6.1.4.1.9.9.136.1.4.2.1.1	Counter64	read-only	This object identifies the number of 1 byte errors that were corrected since the the radio link reached linkOperational state.
C64 cwrArq2ByteErrs	1.3.6.1.4.1.9.9.136.1.4.2.1.2	Counter64	read-only	This object identifies the number of consecutive 2 byte errors that were corrected since the the radio link reached linkOperational state.
C64 cwrArq3ByteErrs	1.3.6.1.4.1.9.9.136.1.4.2.1.3	Counter64	read-only	This object identifies the number of consecutive 3 byte errors that were corrected since the the radio link reached linkOperational state.
C64 cwrArq4ByteErrs	1.3.6.1.4.1.9.9.136.1.4.2.1.4	Counter64	read-only	This object identifies the number of consecutive 4 byte errors that were corrected since the the radio link reached linkOperational state.
C64 cwrArq5ByteErrs	1.3.6.1.4.1.9.9.136.1.4.2.1.5	Counter64	read-only	This object identifies the number of consecutive 5 byte errors that were corrected since the the radio link reached linkOperational state.
C64 cwrArq6ByteErrs	1.3.6.1.4.1.9.9.136.1.4.2.1.6	Counter64	read-only	This object identifies the number of consecutive 6 byte errors that were corrected since the the radio link reached linkOperational state.
C64 cwrArq7ByteErrs	1.3.6.1.4.1.9.9.136.1.4.2.1.7	Counter64	read-only	This object identifies the number of consecutive 7 byte errors that were corrected since the the radio link reached linkOperational state.
C64 cwrArq8ByteErrs	1.3.6.1.4.1.9.9.136.1.4.2.1.8	Counter64	read-only	This object identifies the number of consecutive 8 byte errors that were corrected since the the radio link reached linkOperational state.
C64 cwrArq9ByteErrs	1.3.6.1.4.1.9.9.136.1.4.2.1.9	Counter64	read-only	This object identifies the number of consecutive 9 byte errors that were corrected since the the radio link reached linkOperational state.
I32 cwrArqBurstSize	1.3.6.1.4.1.9.9.136.1.4.1.1.4	Integer32	read-write	This object specifies the maximum number of consecutive ARQ codewords that will be transmitted. ARQ codewords are transmitted for error correction. When an ARQ codeword is transmitted, a data codeword cannot be transmitted in that time slot, resulting jitter on the received data stream. Lower the value of the burst size, lower the peak jitter values.
I32 cwrArqDataLatency	1.3.6.1.4.1.9.9.136.1.4.1.1.3	Integer32	read-write	This object specifies the expected latency values for data. Reducing the latency, provides the ARQ engine less time to correct codeword errors. So if latency is reduced sufficiently, the data throughput will get effected. Also note that the latency values on both ends of the link should be kept identical, else the data throughput will be effected.
I32 cwrArqMaxLatencyJitter	1.3.6.1.4.1.9.9.136.1.4.1.1.7	Integer32	read-only	This object specifies the maximum latency jitter introduced by the ARQ engine, based on the settings defined in this table.
I32 cwrArqMinBitRate	1.3.6.1.4.1.9.9.136.1.4.1.1.6	Integer32	read-only	This object specifies the minimum error free bit rate that is supported on this link given the current configuration as specified in the cwrRadioPhyTable and the settings in this table.
T/F cwrArqOn	1.3.6.1.4.1.9.9.136.1.4.1.1.9	TruthValue	read-write	This object when set to true will enable the Automatic Repeat Query subsystem. Disabling the ARQ subsystem disables a major error correction mechanism of the radio, due to which an operating radio PHY may suffer large performance degradation.
INT cwrArqPctBw	1.3.6.1.4.1.9.9.136.1.4.1.1.1	INTEGER	read-write	This object specifies the percentage of the total radio PHY bandwidth available to the ARQ engine. Some or all of this allocated bandwidth is used to when detected errors are corrected. The percentage will be approximated to the closest value supported by the ARQ engine.
T/F cwrArqReset	1.3.6.1.4.1.9.9.136.1.4.1.1.8	TruthValue	read-write	This object when set to true will force the PHY quality parameters to be reset from the cwrRadioPhyTable. Reading this object will always return false. This is useful when arbitrary changes to the ARQ parameters have to be reset to known consistent valid values.
I32 cwrArqTypicalBitRate	1.3.6.1.4.1.9.9.136.1.4.1.1.5	Integer32	read-only	This object specifies the typical error free bit rate that is possible on this link given the current configuration as specified in the cwrRadioPhyTable. If the radio channel is excessively noisy then the bit rate will be lower than this value
I32 cwrArqVoiceLatency	1.3.6.1.4.1.9.9.136.1.4.1.1.2	Integer32	read-only	This object identifies the latency value for voice data.
C32 cwrAutomaticSyncLoss	1.3.6.1.4.1.9.9.136.1.6.2.1.12	Counter32	read-only	This object represents number of times the radio link was synchronized but lost synchronization with the remote end without manual or higher layer protocol layer intervention.
C32 cwrAvailableSeconds	1.3.6.1.4.1.9.9.136.1.6.2.1.1	Counter32	read-only	This object represents the number of Available Seconds cumulated since the link was powered up. It is equal to: Error Free Seconds + Errored Seconds - Severely Errored Seconds.
INT cwrBandwidth	1.3.6.1.4.1.9.9.136.1.3.2.1.2	INTEGER	read-write	This object specifies the bandwidth to use. Given bandwidth, the actual throughput of the radio link is determined by the cwrThroughput setting.
T/F cwrBasePrivacySupport	1.3.6.1.4.1.9.9.136.1.3.1.1.4	TruthValue	read-only	This object specifies whether the Baseline Privacy feature is available for use on this radio interface. If true then privacy is supported.
I32 cwrBinDelta	1.3.6.1.4.1.9.9.136.1.7.1.1.6	Integer32	read-create	This object represents the range of values of the sampled data that should be accounted for in one histogram bin. For example all data samples between x..y (where y = x + cwrBinDelta - 1), will be counted and placed in the same bin.
INT cwrBurstSize	1.3.6.1.4.1.9.9.136.1.3.2.1.11	INTEGER	read-write	This object defines the time duration of the data burst sent over the air. The burst size is dependant on the capability of the ODU which is represented by the cwrBurstSizeGroup variable in the cwrRfTable. The user must set this object based on the value of cwrBurstSizeGroup in the cwrRfTable. The approximate time duration for each of the burst sizes are: small(1): 50 microseconds medium(2): 100 microseconds large(3): 200 microseconds
OCT cwrBurstSizeGroup	1.3.6.1.4.1.9.9.136.1.5.1.1.17	OCTET STRING	read-only	This object indicates the range or burst sizes supported by the ODU. This information is read from the ODU EEPROM. The user may set the cwrBurstSize MIB object in the cwrRadioPhyTable based on the value of this object.
INT cwrCableLoss	1.3.6.1.4.1.9.9.136.1.3.2.1.8	INTEGER	read-write	This object represents the measured loss in signal power in dB that is imposed by the cable connecting the radio to the antenna head. This value enables the hardware to compensate for the cable loss by adjusting the gain appropriately. A value of 0 represents no degradation in signal due to the cable. This cable loss applies to the transmit antenna identified by cwrTxRfIndex.
INT cwrCableLossDiversity	1.3.6.1.4.1.9.9.136.1.3.2.1.10	INTEGER	read-write	This object represents the measured loss in signal power in dB that is imposed by the cable connecting the radio to the antenna head. This value enables the hardware to compensate for the cable loss by adjusting the gain appropriately. A value of 0 represents no degradation in signal due to the cable. This cable loss applies to the receive antenna identified by cwrRxRf2Index.
T/F cwrClockRefExt	1.3.6.1.4.1.9.9.136.1.3.1.1.8	TruthValue	read-write	When this object is set to true(1), the wireless radio uses a 10MHz external reference clock.
I32 cwrCollDuration	1.3.6.1.4.1.9.9.136.1.7.1.1.9	Integer32	read-create	This object specifies the duration for which this histogram must be accumulated. After successfully accumulating data for this amount of time the collection stops and the cwrHistStatus changes to statusCaptured.
cwrComplianceHistoryGroup	1.3.6.1.4.1.9.9.136.3.2.6			Group of objects implemented in the point to point wireless system for capturing histograms of radio signal parameters on the radio interface.
cwrComplianceNotifGroup	1.3.6.1.4.1.9.9.136.3.2.11			A group of notifications. Note that none of these notifications were originally defined with an OID having 0 as its next-to-last sub-identifier. Therefore, none of these notifications are reverse-mappable between SNMPv1 and SNMPv2/SNMPv3.
cwrComplianceRadioAntennaGroup	1.3.6.1.4.1.9.9.136.3.2.9			Group of objects implemented in the point to point wireless system for managing the antennas available in the system.
cwrComplianceRadioGroup	1.3.6.1.4.1.9.9.136.3.2.1			Group of objects implemented to configure a point to point wireless radio. This includes the cwrBurstSize object.
cwrComplianceRadioPhyByteErrGroup	1.3.6.1.4.1.9.9.136.3.2.10			Group of objects implemented in the point to point wireless system for tracking the number of errored bytes that were automatically corrected.
cwrComplianceRadioPhyQualityGroup	1.3.6.1.4.1.9.9.136.3.2.2			Group of objects implemented to tune phy quality in the point to point wireless systems.
cwrComplianceRadioRfGroup	1.3.6.1.4.1.9.9.136.3.2.3			Group of objects implemented to tune phy quality in the point to point wireless systems. This group includes cwrBurstSizeGroup.
cwrComplianceRadioSnapshotGroup	1.3.6.1.4.1.9.9.136.3.2.8			Group of objects implemented in the point to point wireless system for capturing snapshots of various parameters on the radio interface.
cwrComplianceRadioTestGroup	1.3.6.1.4.1.9.9.136.3.2.5			Group of objects implemented in the point to point wireless system for Testing the link.
cwrComplianceRadioTlGroup	1.3.6.1.4.1.9.9.136.3.2.7			Group of objects implemented in the point to point wireless system for establishing thresholds and capturing timeline data.
cwrComplianceReqLinkMetrics	1.3.6.1.4.1.9.9.136.3.2.4			Required Radio link metrics objects for the point to point wireless systems.
cwrCumulativeMetricsEntry	1.3.6.1.4.1.9.9.136.1.6.2.1		not-accessible	There exists one such entry for every interface in the ifTable which has an ifType of propWirelessP2P(157). Each of these entries are indexed by the value of ifIndex as defined in RFC2863.
cwrCumulativeMetricsTable	1.3.6.1.4.1.9.9.136.1.6.2		not-accessible	This table contains metrics used to measure the quality of the radio link identified by the ifIndex. The metrics in this table are cumulated since the last time the system powered up.
INT cwrDspNumber	1.3.6.1.4.1.9.9.136.1.7.1.1.4	INTEGER	read-create	This object identifies the DSP on which to create the histogram. If 0 is specified then the agent will automatically use the most logical DSP for the specified cwrHistClass parameter. If 0 has been specified then on reading this object the agent will return the DSP number that is being used to capture this histogram.
G32 cwrEffectivePhyDataRate	1.3.6.1.4.1.9.9.136.1.6.2.1.15	Gauge32	read-only	This object represents the effective data throughput of this link while the link was synchronized.
CWR cwrHistAction	1.3.6.1.4.1.9.9.136.1.7.1.1.14	CwrCollectionAction	read-create	This object represents the action to be carried out on this histogram specification. If a histogram has been successfully captured then it must be cleared before an other capture may be initiated.
INT cwrHistBinIndex	1.3.6.1.4.1.9.9.136.1.7.3.1.1	INTEGER	not-accessible	This object represents the histogram bin number for the value in cwrValue.
INT cwrHistBitShift	1.3.6.1.4.1.9.9.136.1.7.1.1.11	INTEGER	read-create	This object represents the number of bits by which the signal count is right shifted before it is stored in the histogram bin. This provides a mechanism to uniformly scale the collected histogram to account for overflows.
CWR cwrHistClass	1.3.6.1.4.1.9.9.136.1.7.1.1.2	CwrRadioSignalAttribute	read-create	This object represents the attribute that is being histogrammed.
cwrHistCtrlEntry	1.3.6.1.4.1.9.9.136.1.7.1.1		not-accessible	This represents one entry in the cwrHistogramTable. It is indexed by the ifIndex, cwrHistIndex.
cwrHistCtrlTable	1.3.6.1.4.1.9.9.136.1.7.1		not-accessible	This table contains information about histograms configured in hardware. When data is collected it will be stored in histogram bins as follows: All values (X (cwrStartBinValue + (cwrNumBins - 2) * cwrBinDelta)), i.e. any value that is greater than that may be stored in the last bin.
cwrHistDataEntry	1.3.6.1.4.1.9.9.136.1.7.3.1		not-accessible	This represents one entry in the cwrHistDataTable. It is indexed by the ifIndex and cwrHistIndex and cwrHistBinIndex.
cwrHistDataTable	1.3.6.1.4.1.9.9.136.1.7.3		not-accessible	This table contains histogram values collected based on the specifications in the cwrHistCtrlTable.
I32 cwrHistIndex	1.3.6.1.4.1.9.9.136.1.7.1.1.1	Integer32	not-accessible	This object, along with ifIndex, is the index into this table and represents one entry in the table. The entry in this table for which cwrHistIndex = x is associated with the entry in cwrHistSummaryTable and the entry in cwrHistDataTable for which the index variable in those tables has the same value, x.
I32 cwrHistMax	1.3.6.1.4.1.9.9.136.1.7.2.1.3	Integer32	read-only	This object represents the maximum value of the data sample seen for this histogram.
I32 cwrHistMean	1.3.6.1.4.1.9.9.136.1.7.2.1.4	Integer32	read-only	This object represents the arithemetic mean of the data sample values for this histogram.
I32 cwrHistMin	1.3.6.1.4.1.9.9.136.1.7.2.1.2	Integer32	read-only	This object represents the minimum value of the data sample seen for this histogram.
T/F cwrHistPeriodicSum	1.3.6.1.4.1.9.9.136.1.7.1.1.17	TruthValue	read-create	The histogram data is updated every cwrUpdateRate seconds. When this object is set to true(1), the latest histogram data set is summed with the previous histogram data set and the cwrHistSummaryTable will reflect cumulative values. When set to false(2), only the latest data set is made available and the cwrHistSummarytable will reflect the latest values.
ROW cwrHistRowStatus	1.3.6.1.4.1.9.9.136.1.7.1.1.16	RowStatus	read-create	This object may be used to create or delete a histogram control specification.
CWR cwrHistStatus	1.3.6.1.4.1.9.9.136.1.7.1.1.15	CwrCollectionStatus	read-only	This object represents the current state of this histogram collection. Once the histogram collection is complete the status changes statusCaptured and the data is available for use. None of the parameters of a histogram specification may be modified when the specification is in statusInProgress. A statusCaptured or statusStopped histogram must be actionClear'ed before another histogram specification may be started. The histogram may be read accurately between the cwrUpdateRate intervals. If the read spans across the update time data from the previous and current updates can be mingled.
cwrHistSummaryEntry	1.3.6.1.4.1.9.9.136.1.7.2.1		not-accessible	This represents one entry in the cwrHistSummaryTable. It is indexed by the ifIndex and cwrHistIndex.
cwrHistSummaryTable	1.3.6.1.4.1.9.9.136.1.7.2		not-accessible	This table contains histogram Summary collected based on the specifications in the cwrHistCtrlTable.
INT cwrHistToneSelection	1.3.6.1.4.1.9.9.136.1.7.1.1.12	INTEGER	read-create	This object identifies which tone in a burst should be sampled for capturing the data. cwrCirculate(1): The successive tones will be used for every successive burst. cwrAverage(2): The value of every tone in a burst will be averaged. cwrspecific(3): The identified tone is used.
I32 cwrHistToneValue	1.3.6.1.4.1.9.9.136.1.7.1.1.13	Integer32	read-create	If cwrHistToneSelection is cwrSpecificTone then this object identifies tone that should be used for sampling.
I32 cwrHistUpdateTime	1.3.6.1.4.1.9.9.136.1.7.2.1.1	Integer32	read-only	This object represents the time in seconds since power up when this histogram snapshot was retrieved from the hardware.
I32 cwrIfInpFreq	1.3.6.1.4.1.9.9.136.1.5.2.1.5	Integer32	read-only	This object represents the IF input frequency.
I32 cwrIfOutFreq	1.3.6.1.4.1.9.9.136.1.5.2.1.6	Integer32	read-only	This object represents the IF output frequency.
CWR cwrIfRefOscState	1.3.6.1.4.1.9.9.136.1.5.2.1.3	CwrOscState	read-only	This object represents the state of the IF reference oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
I32 cwrIfResIndex	1.3.6.1.4.1.9.9.136.1.5.2.1.4	Integer32	read-only	This object represents the index into CwrIntFreqEntityTable. It identifies the intermediate frequency resource.
CWR cwrIfRxOscState	1.3.6.1.4.1.9.9.136.1.5.2.1.2	CwrOscState	read-only	This object represents the state of the IF receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
CWR cwrIfTxOscState	1.3.6.1.4.1.9.9.136.1.5.2.1.1	CwrOscState	read-only	This object represents the state of the IF transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
I32 cwrImaginaryPart	1.3.6.1.4.1.9.9.136.1.9.3.1.3	Integer32	read-only	The data sample value. Imaginary part if the attribute is represented by a complex number.
cwrIntFreqEntry	1.3.6.1.4.1.9.9.136.1.5.2.1		not-accessible	This represents one entry in the cwrIntFreqTable. This table is largely a read only table which provides details on the state of the intermediate frequency subsystem available on the wireless radio.
cwrIntFreqTable	1.3.6.1.4.1.9.9.136.1.5.2		not-accessible	This table contains information about the state of the intermediate frequency subsystem on the wireless radio.
NUM cwrLastSyncFailTime	1.3.6.1.4.1.9.9.136.1.6.2.1.14	TimeInterval	read-only	This object represents elapsed time since the radio link lost synchronization with the remote end.
NUM cwrLastSyncSuccessTime	1.3.6.1.4.1.9.9.136.1.6.2.1.13	TimeInterval	read-only	This object represents elapsed time since the radio link successfully synchronized with the remote end.
U32 cwrLink1HrCSESAlarmThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.7	Unsigned32	read-write	This object specifies the one hour Codeword Consecutively Severely Errored Seconds threshold. When the number of Codeword Severely Errored Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink1HrThresh trap will be generated. Time measurement starts after the first operational second.
U32 cwrLink1HrDCMAlarmThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.8	Unsigned32	read-write	This object specifies the one hour Degraded Codeword Minute threshold. When the number of Degraded Codeword Minutes in a 1 Operational Hour period exceeds this limit cwrTrapLink1HrThresh trap will be generated. Time measurement starts after the first operational second.
U32 cwrLink1HrESAlarmThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.5	Unsigned32	read-write	This object specifies the one hour Codeword Error Second threshold. When the number of Codeword Error Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink1HrThresh trap will be generated. Time measurement starts after the first operational second.
U32 cwrLink1HrSESAlarmThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.6	Unsigned32	read-write	This object specifies the one hour Codeword Severely Errored Seconds threshold. When the number of Codeword Severely Errored Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink1HrThresh trap will be generated. Time measurement starts after the first operational second.
U32 cwrLink24HrCSESAlarmThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.11	Unsigned32	read-write	This object specifies the one hour Codeword Consecutively Severely Errored Seconds threshold. When the number of Codeword Severely Errored Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink24HrThresh trap will be generated. Time measurement starts after the first operational second.
U32 cwrLink24HrDCMAlarmThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.12	Unsigned32	read-write	This object specifies the one hour Degraded Codeword Minute threshold. When the number of Degraded Codeword Minutes in a 1 Operational Hour period exceeds this limit cwrTrapLink24HrThresh trap will be generated. Time measurement starts after the first operational second.
U32 cwrLink24HrESAlarmThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.9	Unsigned32	read-write	This object specifies the 24 hour Codeword Error Second threshold. When the number of Codeword Error Seconds in a 24 Operational Hour period exceeds this limit cwrTrapLink24HrThresh trap will be generated. Time measurement starts after the first operational second.
U32 cwrLink24HrSESAlarmThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.10	Unsigned32	read-write	This object specifies the one hour Codeword Severely Errored Seconds threshold. When the number of Codeword Severely Errored Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink24HrThresh trap will be generated. Time measurement starts after the first operational second.
U32 cwrLinkCSESThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.4	Unsigned32	read-write	When the number of severely errored codewords detected consecutively in one second equals this threshold value, the second is counted as a Consecutively Severely Errored Second.
U32 cwrLinkCwESThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.1	Unsigned32	read-write	If the number of Codeword Errors detected in a duration of 1 Operational second, is greater than this value then that second is counted as an Errored Second.
U32 cwrLinkHighCwDSThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.3	Unsigned32	read-write	This object specifies high degraded second threshold. When then number of codeword errors detected are greater than this value then that second is counted as a Codeword Severely Errored Second.
U32 cwrLinkLowCwDSThresh	1.3.6.1.4.1.9.9.136.1.6.1.1.2	Unsigned32	read-write	This object specifies low degraded second threshold. When the number of codeword errors detected are greater or equal than this value and less than cwrLinkHighCwDSThresh then that second is counted as a Codeword Degraded Second.
cwrLinkMetricsThreshEntry	1.3.6.1.4.1.9.9.136.1.6.1.1		not-accessible	There exists one such entry for every interface in the ifTable which has an ifType of propWirelessP2P(157). Each of these entries are indexed by the value of ifIndex as defined in RFC2863.
cwrLinkMetricsThresholdTable	1.3.6.1.4.1.9.9.136.1.6.1		not-accessible	This table contains threshold values that are the trigger points for controlling the collection of the Link Metrics such as Codeword Errored Seconds and others.
INT cwrLocalLoopbackPoint	1.3.6.1.4.1.9.9.136.1.1.1.1.1.1	INTEGER	read-write	This object represents the point in the system where the data signal is looped back. none(0) - no loopback codec(1) - loopback at the Encoder/Decoder module. This exercises the framer, and codec modules framer(2) - loopback at the 'framer' module. fir(3) - loopback at the 'Finite Impulse Response' module. This exercises the framer, codec, and FIR modules. if(4) - loopback at the 'Internal Frequency' module using both the main and the diversity receive paths. This exercises the framer, codec, FIR, and IF modules. rf(5) - loopback at the main RF unit via the main receive path in the IF module. This exercises the framer, codec, FIR, IF, and RF modules. rfDiversity(6) - loopback at the main RF unit but route it through the diversity receive path in the IF module. This exercises the framer, codec, FIR, IF, and RF modules. ifMain(7) - loopack at the IF module using only the Main receive path. This exercises the framer, codec, FIR, and IF modules. ifDiversity(8) - loopack at the IF module using only the diversity receive path. This exercises the framer, codec, FIR, and IF modules.
cwrLoopbackEntry	1.3.6.1.4.1.9.9.136.1.1.1.1.1		not-accessible	There exists one such entry for every interface in the ifTable which has an ifType of propWirelessP2P(157).
cwrLoopbackTable	1.3.6.1.4.1.9.9.136.1.1.1.1		not-accessible	This table provides facilities to establish loopback points in the radio hardware to exercise various sections of the hardware.
C32 cwrManagedSyncLoss	1.3.6.1.4.1.9.9.136.1.6.2.1.11	Counter32	read-only	This object represents number of times the radio link layer was shutdown by operator intervention or a higher layer protocol.
I32 cwrMaxTxPower	1.3.6.1.4.1.9.9.136.1.5.1.1.9	Integer32	read-only	This object represents the maximum power that the RF subsystem can supply the antenna.
I32 cwrMinTxPower	1.3.6.1.4.1.9.9.136.1.5.1.1.8	Integer32	read-only	This object represents the minimum power that the RF subsystem can supply the antenna.
I32 cwrNumHistBins	1.3.6.1.4.1.9.9.136.1.7.1.1.7	Integer32	read-create	This object represents total number of bins to be created for the histogram.
INT cwrNumRxAntenna	1.3.6.1.4.1.9.9.136.1.3.2.1.1	INTEGER	read-write	This object specifies the number of antennas to be used to receive the wireless transmissions.
INT cwrOperatingBand	1.3.6.1.4.1.9.9.136.1.3.2.1.4	INTEGER	read-write	This object represents the portion of the frequency spectrum in which the radio PHY will operate. bandUNII(1) - The U-NII (Unlicensed National Information Infrastructure) band represents the frequency range 5725.25 to 5823.75 MHz. bandMMDS(2) - The MMDS (Multichannel Multipoint Distribution Service) band represents the frequency range 2150.75 to 2688.25 MHz. bandOther(3)- For all other frequenciy ranges.
INT cwrOpStatus	1.3.6.1.4.1.9.9.136.1.3.2.1.9	INTEGER	read-only	This represents the current state of a radio Link. notOperational(1): The link is not operational. selftest(2) : Power on self test in progress download(3): Image download is in progress. txOnly(4): The radio link will switch to this state if the radio link is configured for transmit only. acquiring(5): Attempting to sync up with the far end transmitter. receiveUp(6): The receive side of the radio link has successfully sync'ed up with remote end. transmitUp(7): Transmit side of the radio link is up and running. linkOperational(8): The radio link is ready for duplex communication.
STR cwrOwnerId	1.3.6.1.4.1.9.9.136.1.7.1.1.10	OwnerString	read-create	This object identifies management station that created this histogram specification.
G32 cwrPctAvailSeconds	1.3.6.1.4.1.9.9.136.1.6.2.1.7	Gauge32	read-only	This object represents the ratio of cumulative Available seconds to Link Admin Up seconds, expressed as a percentage.
G32 cwrPctCwDegradedMinutes	1.3.6.1.4.1.9.9.136.1.6.2.1.8	Gauge32	read-only	This object represents the ratio of cumulative Codeword Degraded Minutes to Link Admin Up seconds, expressed as a percentage.
G32 cwrPctEffectivePhyDataRate	1.3.6.1.4.1.9.9.136.1.6.2.1.16	Gauge32	read-only	This object represents the ratio of total error free codewords received to the total codewords received as a percentage.
G32 cwrPctErroredSeconds	1.3.6.1.4.1.9.9.136.1.6.2.1.5	Gauge32	read-only	This object represents the ratio of cumulative Codeword Errored Seconds (ES) to Link Admin Up seconds, expressed as a percentage.
G32 cwrPctErrorFreeSeconds	1.3.6.1.4.1.9.9.136.1.6.2.1.4	Gauge32	read-only	This object represents the ratio of cumulative Codeword Error Free Seconds (EFS) to Link Admin Up seconds, expressed as a percentage.
G32 cwrPctSeverelyErroredSeconds	1.3.6.1.4.1.9.9.136.1.6.2.1.6	Gauge32	read-only	This object represents the ratio of cumulative Codeword Severely Errored Seconds (SES) to Link Admin Up seconds, expressed as a percentage.
cwrPhyCorrectedBytesEntry	1.3.6.1.4.1.9.9.136.1.4.2.1		not-accessible	There exists one such entry for every interface in the ifTable which has an ifType of propWirelessP2P(157). Each of these entries are indexed by the value of ifIndex as defined in RFC2863.
cwrPhyCorrectedBytesTable	1.3.6.1.4.1.9.9.136.1.4.2		not-accessible	This provides information on the number of byte detected and corrected by the ARQ engine. The ARQ engine can correct up to 9 consecutive byte errors. This table keeps a count of the number of byte errors corrected over time. The values in this table are cumulated from link power up.
cwrPhyQualityEntry	1.3.6.1.4.1.9.9.136.1.4.1.1		not-accessible	There exists one such entry for every interface in the ifTable which has an ifType of propWirelessP2P(157). Each of these entries are indexed by the value of ifIndex as defined in RFC2863.
cwrPhyQualityTable	1.3.6.1.4.1.9.9.136.1.4.1		not-accessible	This table contains information about the radio PHY quality control parameters. Note that the parameters in this table are automatically determined by the parameters configured in the cwrRadioPhyTable. These parameters may further be used to tune the characteristics when needed.
cwrRadioAntennaGroup	1.3.6.1.4.1.9.9.136.1.10
cwrRadioBaseEntry	1.3.6.1.4.1.9.9.136.1.3.1.1		not-accessible	There exists one such entry for every interface in the ifTable which has an ifType of propWirelessP2P(157). Each of these entries are indexed by the value of ifIndex as defined in RFC2863.
cwrRadioBaseGroup	1.3.6.1.4.1.9.9.136.1.3
cwrRadioBaseTable	1.3.6.1.4.1.9.9.136.1.3.1		not-accessible	This table contains information about the radio common to both the transmit and receive sides.
cwrRadioBasicCompliance	1.3.6.1.4.1.9.9.136.3.1.1			The compliance statement for devices that Point to Point wireless interface compliant to Cisco Systems Inc. specification.
cwrRadioCommon	1.3.6.1.4.1.9.9.136.1.2
cwrRadioDevTraps	1.3.6.1.4.1.9.9.136.2.2
cwrRadioFreqResGroup	1.3.6.1.4.1.9.9.136.1.5
cwrRadioHistoryGroup	1.3.6.1.4.1.9.9.136.1.7
cwrRadioIfCompliances	1.3.6.1.4.1.9.9.136.3.1
cwrRadioIfConformance	1.3.6.1.4.1.9.9.136.3
cwrRadioIfGroups	1.3.6.1.4.1.9.9.136.3.2
cwrRadioInternal	1.3.6.1.4.1.9.9.136.1.1
cwrRadioLatestTrap	1.3.6.1.4.1.9.9.136.2.1
cwrRadioMetricsGroup	1.3.6.1.4.1.9.9.136.1.6
cwrRadioMibObjects	1.3.6.1.4.1.9.9.136.1
I32 cwrRadioNextIndex	1.3.6.1.4.1.9.9.136.1.2.1	Integer32	read-only	This object should be used to generate unique indices when creating rows in the cwrRadioHistoryGroup, cwrRadioTimelineGroup, and the cwrRadioSnapshotGroup. Every GET request will generate a new index. The index will not be unique across power cycles of the router.
cwrRadioNotification	1.3.6.1.4.1.9.9.136.2
cwrRadioPhyEntry	1.3.6.1.4.1.9.9.136.1.3.2.1		not-accessible	There exists one such entry for every interface in the ifTable which has an ifType of propWirelessP2P(157). Each of these entries are indexed by the value of ifIndex as defined in RFC2863.
cwrRadioPhyQualityGroup	1.3.6.1.4.1.9.9.136.1.4
cwrRadioPhyTable	1.3.6.1.4.1.9.9.136.1.3.2		not-accessible	This table contains information about the currently configured physical layer. These configuration paramters must match the corresponding configuration parameter at the remote end for the wireless link to be established.
cwrRadioSnapshotGroup	1.3.6.1.4.1.9.9.136.1.9
cwrRadioThreshTraps	1.3.6.1.4.1.9.9.136.2.3
cwrRadioTimelineGroup	1.3.6.1.4.1.9.9.136.1.8
cwrRadioTrapEntry	1.3.6.1.4.1.9.9.136.2.1.1.1		not-accessible	This represents one entry in this table.
cwrRadioTrapTable	1.3.6.1.4.1.9.9.136.2.1.1		not-accessible	This table provides information about the last trap that was generated on this interface.
I32 cwrRealPart	1.3.6.1.4.1.9.9.136.1.9.3.1.2	Integer32	read-only	The data sample value. Real part.
I32 cwrRfAntIndex	1.3.6.1.4.1.9.9.136.1.5.1.1.11	Integer32	read-only	This object represents the index into the cwrAntennaTable. This object may be 0 if the cwrAntennaTable is not available.
INT cwrRfControlChannelStatus	1.3.6.1.4.1.9.9.136.1.5.1.1.16	INTEGER	read-only	Each RF resource has an associated control channel. The control channel is used to send/receive control information to the RF resource. For the RF resouce to operate properly, the control channel must be established. This object indicates the status of the control channel ok(1) - RF resource may be controlled successfully notOk(2) - Cannot talk to the RF resource.
cwrRfEntry	1.3.6.1.4.1.9.9.136.1.5.1.1		not-accessible	This represents one entry in the cwrRfTable. This table is largely a read only table which provides details on the state of radio frequency resources available on the system. Physically each RF resource may be realized by one antenna and its associated control hardware. A single antenna and its associated electronics may act as more than 1 RF resource. When an RF resource acts as both a transmit and receive resource, the transmit and receive frequency ranges may overlap. It is indexed by the ifIndex and cwrRfIndex.
I32 cwrRfIndex	1.3.6.1.4.1.9.9.136.1.5.1.1.1	Integer32	not-accessible	This object, along with ifIndex, represents the index of this entry in the cwrRfTable.
INT cwrRFOpMode	1.3.6.1.4.1.9.9.136.1.5.1.1.3	INTEGER	read-only	This object indicates if this RF resource is being used to either receive, transmit, or both.
I32 cwrRfResIndex	1.3.6.1.4.1.9.9.136.1.5.1.1.2	Integer32	read-only	This object represents the index into CwrRfEntityTable. This index identifies the radio frequency resource.
CWR cwrRfResourceId	1.3.6.1.4.1.9.9.136.1.7.1.1.3	CwrRFZeroIndex	read-create	This object identifies the RF resource for which this histogram specification applies. If this is 0, the agent will automatically use the most logical value for the specified cwrHistClass. If 0 has been specified then on reading this object the agent will return the RF resource id for which the histogram is being captured.
CWR cwrRfRxOscState	1.3.6.1.4.1.9.9.136.1.5.1.1.12	CwrOscState	read-only	This object represents the state of the receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
INT cwrRfStatus	1.3.6.1.4.1.9.9.136.1.5.1.1.15	INTEGER	read-only	This object specifies whether the RF resource is functioning properly or not. If it is functioning properly then it will be online(1), else offline(2).
INT cwrRfSupplyVoltageState	1.3.6.1.4.1.9.9.136.1.5.1.1.14	INTEGER	read-only	This object specifies whether the voltage supply to the RF unit is within specifications or not.
cwrRfTable	1.3.6.1.4.1.9.9.136.1.5.1		not-accessible	This table contains information about the state of the radio frequency resources used by the radio link.
I32 cwrRfTemperature	1.3.6.1.4.1.9.9.136.1.5.1.1.13	Integer32	read-only	This object represents the current temperature of the RF unit.
CWR cwrRfTxOscState	1.3.6.1.4.1.9.9.136.1.5.1.1.10	CwrOscState	read-only	This object represents the state of the transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
CWR cwrRx1RfIndex	1.3.6.1.4.1.9.9.136.1.3.1.1.6	CwrRFZeroIndex	read-only	This object specifies the index of the first receive antenna identified by the cwrRfTable. This index will be 0 if the associated receive antenna is not present.
CWR cwrRx2RfIndex	1.3.6.1.4.1.9.9.136.1.3.1.1.7	CwrRFZeroIndex	read-only	This object specifies the index of the second receive antenna in the cwrRfTable. This index will be 0 if the associated receive antenna is not present.
INT cwrRxFreqRangeMax	1.3.6.1.4.1.9.9.136.1.5.1.1.7	INTEGER	read-only	This object represents the highest transmission frequency that this RF resource can receive.
INT cwrRxFreqRangeMin	1.3.6.1.4.1.9.9.136.1.5.1.1.6	INTEGER	read-only	This object represents the lowest transmission frequency this RF resource can receive.
INT cwrRxFrequency	1.3.6.1.4.1.9.9.136.1.3.2.1.6	INTEGER	read-write	This object represents the center frequency that will be used to receive transmissions over the radio PHY. The specified receive frequency must match the operating band and the capability of the RF resource connected to the radio. The transmit frequency at the local end must be identical to the receive frequency at the remote end for a wireless link to be established.
I32 cwrScopePortAttribute	1.3.6.1.4.1.9.9.136.1.1.1.2.1.3	Integer32	read-write	This represents the attribute to be redirected to the scope port. The attributes that may be redirected to scope port is the same as that identified in cwrSnapshotType.
INT cwrScopePortDsp	1.3.6.1.4.1.9.9.136.1.1.1.2.1.2	INTEGER	read-write	This identifies the DSP that should redirect a portion of the signal data to the scope port.
cwrScopePortEntry	1.3.6.1.4.1.9.9.136.1.1.1.2.1		not-accessible	There exists one such entry for every interface in the ifTable which has an ifType of propWirelessP2P(157).
T/F cwrScopePortOn	1.3.6.1.4.1.9.9.136.1.1.1.2.1.1	TruthValue	read-write	If set to true(1), then the DSP identified by cwrScopePortDsp, will redirect a portion of the output signal for the attribute identified by cwrScopeAttribute to the scope port.
cwrScopePortTable	1.3.6.1.4.1.9.9.136.1.1.1.2		not-accessible	This table provides facilities to redirect a portion of the signal being processed by a DSP to a scope port on the radio. An oscilloscope may be connected to the scope port to analyze the signal.
INT cwrSelfTest	1.3.6.1.4.1.9.9.136.1.3.1.1.3	INTEGER	read-write	This object specifies the whether self test should be executed and if so whether to do it every time the radio link is started. Any changes made to this object will reflected the next time the radio link is started. off(1) - Self test never performed. once(2) - Self test will be performed the next time the radio link is started. always(3) - Every time the radio link is started.
I32 cwrSnapAttr1Id	1.3.6.1.4.1.9.9.136.1.9.2.1.2	Integer32	read-only	This object represents the first snapshot attribute value.
I32 cwrSnapAttr1Size	1.3.6.1.4.1.9.9.136.1.9.2.1.3	Integer32	read-only	This object represents the number of values captured for the snapshot cwrSnapAttr1Id.
I32 cwrSnapAttr2Id	1.3.6.1.4.1.9.9.136.1.9.2.1.4	Integer32	read-only	This object represents the second snapshot attribute value.
I32 cwrSnapAttr2Size	1.3.6.1.4.1.9.9.136.1.9.2.1.5	Integer32	read-only	This object represents the number of values captured for the snapshot cwrSnapAttr2Id.
I32 cwrSnapAttr3Id	1.3.6.1.4.1.9.9.136.1.9.2.1.6	Integer32	read-only	This object represents the third snapshot attribute value.
I32 cwrSnapAttr3Size	1.3.6.1.4.1.9.9.136.1.9.2.1.7	Integer32	read-only	This object represents the number of values captured for the snapshot cwrSnapAttr3Id.
I32 cwrSnapAttr4Id	1.3.6.1.4.1.9.9.136.1.9.2.1.8	Integer32	read-only	This object represents the third snapshot attribute value.
I32 cwrSnapAttr4Size	1.3.6.1.4.1.9.9.136.1.9.2.1.9	Integer32	read-only	This object represents the number of values captured for the snapshot cwrSnapAttr4Id.
cwrSnapDataEntry	1.3.6.1.4.1.9.9.136.1.9.3.1		not-accessible	This represents one entry in the cwrSnapDataTable. It is indexed by the ifIndex and cwrSnapValueIndex. The values in this table represent real numbers or complex numbers. If they are real numbers then cwrRealPart contains the data and cwrImaginaryPart is zero.
cwrSnapDataTable	1.3.6.1.4.1.9.9.136.1.9.3		not-accessible	This table contains snapshot values collected based on the specifications in the cwrSnapshotCtrlTable.
CWR cwrSnapshotAction	1.3.6.1.4.1.9.9.136.1.9.1.1.3	CwrCollectionAction	read-create	This object represents the action to be carried out on this snapshot specification. If a snapshot has been successfully captured then it must be cleared before an other capture may be initiated.
cwrSnapshotCtrlEntry	1.3.6.1.4.1.9.9.136.1.9.1.1		not-accessible	This represents one entry in the cwrSnapshotCtrlTable It is indexed by the ifIndex and cwrSnapshotDspNum.
cwrSnapshotCtrlTable	1.3.6.1.4.1.9.9.136.1.9.1		not-accessible	This table contains information about the snapshots configured in hardware. When data is collected it will be stored in cwrSnapDataTable.
INT cwrSnapshotDspNum	1.3.6.1.4.1.9.9.136.1.9.1.1.1	INTEGER	not-accessible	This object represents the DSP at which the snapshot needs to be collected.
ROW cwrSnapshotRowStatus	1.3.6.1.4.1.9.9.136.1.9.1.1.5	RowStatus	read-create	This object may be used to create or delete this snapshot specification.
CWR cwrSnapshotStatus	1.3.6.1.4.1.9.9.136.1.9.1.1.4	CwrCollectionStatus	read-only	This object represents the current status of this snapshot specification. When the status in statusInProgress none of the snapshot parameters can be configured. When the status is statusCaptured then data is available for use.
I32 cwrSnapshotType	1.3.6.1.4.1.9.9.136.1.9.1.1.2	Integer32	read-create	This object represents the attribute that is being snapshoted by the hardware. When a snapshot request is issued up to 4 simultaneous radio signal attribute may be captured at once. The 4 attributes are specified by bit OR'ing the snapshot types identified below. When a snapshot specification is started all the specified attributes are captured simultaneously. The TX and RX types cannot be mixed. RX, Sync types can be mixed. When a snapshot request is issued up to four radio signal attributes may be requested at once, one from each set: =============================================== Type Set1 Set2 =============================================== RX y1n(x1) y2n(x2) H2k(x80) H1k(x40) - - Sync - FreqCorr(x8000) - FLL_FFT_Sp(x20000) TX CodecIn(x200) IFFTIn(x400) =============================================== =============================================== Type Set3 Set4 =============================================== RX Y2k(x8) Y1k(x4) h1n(x10) h2n(x20) zhat(x100) - Sync FreqOffCF(x2000)() BrstTimeCF(x1000)() - TT_FCorr(x10000) TX - RoundOut(x800) =============================================== () BrstTimeCF cannot be mixed with Set2 () FreqOffCF cannot be mixed with Set1 Note that only the Tx* attributes may be captured on DSP's 1, 2. The attributes are: RxRawBurstAnt1Y1n(0x01): This represents a snapshot of the received signal for RF resource 1. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. RxRawBurstAnt2Y2n(0x02): This represents a snapshot of the received signal for RF resource 2. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. RxSpectrumAnt1Y1k(0x04): This represents a snapshot of the spectrum of the received signal for RF resource 1. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. RxSpectrumAnt2Y2k(0x08): This represents a snapshot of the spectrum of the received signal for RF resource 2. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. RxTimeDomainChannelAnt1H1n(0x10): This represents a snapshot of the time domain channel for RF resource 1. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. RxTimeDomainChannelAnt2H2n(0x20): This represents a snapshot of the time domain channel for RF resource 2. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. RxFreqDomainChannelAnt1H1k(0x40): This represents a snapshot of the frequency domain channel for RF resource 1. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. RxFreqDomainChannelAnt2H2k(0x80), This represents a snapshot of the frequency domain channel for RF resource 2. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. RxConstellationZHatk(0x100): This represents a snapshot of the soft decisions. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. TxCodecInput(0x200): This represents a snapshot of input values to the Tx Code. Units: Real values. Value: 32 bit quantities. TxIFFTInput(0x400): This represents a snapshot of the IFFT signal for the Transmitted data. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. TxRoundOutput(0x800): This represents a snapshot of the Rounded Constellation signal for the Transmitted data. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. SyncBurstTimeCostFunc(0x1000): This represents the timing cost function for Sync bursts. Units: Real values. Value: 32 bit quantities. SynFreqOffsetCostFunc(0x2000): This represents a snapshot of the frequeny offsets. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. SyncFllFreqCorrelation(0x8000): This represents a snapshot of Frequency correlation. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. SyncFllTrainToneCorrelation(0x10000): This represents a snapshot of Frequency locked loop's Training tone correlation. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities. SyncFllFFTSpectrum(0x20000): This represents a snapshot of Frequency locked loop, FFT Spectrum. For every sample the real and imaginary components are captured. Units: (I, q) Value: 32 bit quantities.
cwrSnapSummaryEntry	1.3.6.1.4.1.9.9.136.1.9.2.1		not-accessible	This represents one entry in the cwrSnapSummaryTable. It is indexed by the ifIndex and cwrSnapDspNum.
cwrSnapSummaryTable	1.3.6.1.4.1.9.9.136.1.9.2		not-accessible	This table contains summary information for captured snapshots defined in cwrSnapshotCtrlTable.
INT cwrSnapValueIndex	1.3.6.1.4.1.9.9.136.1.9.3.1.1	INTEGER	not-accessible	This object represents the snapshot entry index number.
I32 cwrStartBinValue	1.3.6.1.4.1.9.9.136.1.7.1.1.5	Integer32	read-create	This object represents the maximum of the values that will be collected in the first bin of the histogram. All values < cwrStartBinValue will be kept in the first histogram bin.
C32 cwrSyncFailureCount	1.3.6.1.4.1.9.9.136.1.6.2.1.10	Counter32	read-only	This object represents number of times the link attempted to synchronize with the far end but failed to.
C32 cwrSyncLossSeconds	1.3.6.1.4.1.9.9.136.1.6.2.1.3	Counter32	read-only	This object represents the number of Link Admin Up Seconds during which the radio link was out of sync with the remote end.
C32 cwrSyncSuccessCount	1.3.6.1.4.1.9.9.136.1.6.2.1.9	Counter32	read-only	This object represents number of times the radio link successfully synchronized with the far end.
cwrTestGroup	1.3.6.1.4.1.9.9.136.1.1.1
CWR cwrThreshAntId	1.3.6.1.4.1.9.9.136.1.8.1.1.4	CwrRFZeroIndex	read-create	This object identifies the RF resource for which this threshold should be defined.
CWR cwrThreshAttribute	1.3.6.1.4.1.9.9.136.1.8.1.1.2	CwrRadioSignalAttribute	read-create	This represents the attribute of a radio link which needs to be thresholded. For each of these attributes, the cwrThreshType identifies the type of change to monitor. When that threshold is exceeded a Trap with appropriate parameters will be generated.
INT cwrThreshDspNum	1.3.6.1.4.1.9.9.136.1.8.1.1.8	INTEGER	read-create	This object indicates the DSP used to monitor this threshold.
NUM cwrThreshHysteresisTime	1.3.6.1.4.1.9.9.136.1.8.1.1.6	TimeInterval	read-create	When radio signals oscillate around threshold values, they potentially flood the system with notifications. This object specifies the amount of time to wait before sending an identical notification if the oscillations continue. Notifications are not generated due to any threshold value which is reached/exceeded/crossed/etc. during this wait time
I32 cwrThreshIndex	1.3.6.1.4.1.9.9.136.1.8.1.1.1	Integer32	not-accessible	This object, along with ifIndex, identifies this entry.
NUM cwrThreshLimitTime	1.3.6.1.4.1.9.9.136.1.8.1.1.7	TimeInterval	read-create	This object specifies the amount of time for which the radio signal should stabilize before a trap is sent to indicate that the radio signal has stabilized.
cwrThresholdEntry	1.3.6.1.4.1.9.9.136.1.8.1.1		not-accessible	This represents one entry in the cwrThresholdTable.
cwrThresholdTable	1.3.6.1.4.1.9.9.136.1.8.1		not-accessible	This table provides facilities to establish thresholds for the radio signals analyzed on the radio interface. A threshold identified in this table may be used to trigger a timeline capture in the cwrTlTable.
ROW cwrThreshRowStatus	1.3.6.1.4.1.9.9.136.1.8.1.1.9	RowStatus	read-create	This object represents the status of this threshold entry. It may be used to create a new threshold specification. For every cwrThreshAttrClass one threshold of cwrThreshType on one DSP may be created.
CWR cwrThreshType	1.3.6.1.4.1.9.9.136.1.8.1.1.3	CwrThreshLimitType	read-create	This object represents the kind of change that needs to be monitored for the cwrThreshAttribute. An event is generated when the following condition is met.
I32 cwrThreshValue	1.3.6.1.4.1.9.9.136.1.8.1.1.5	Integer32	read-create	This object represents the value to be compared against. The cwrThreshType determines the way in which it is used. It is used as follows: if cwrThreshType is .. highThresh : Notify if data sample exceeds the cwrThreshValue. lowThresh : Notify if data sample recedes below the cwrThreshValue. upChange : Notify if data sample increases by more than cwrThreshValue. downChange : Notify if data sample decreases by more than cwrThreshValue. upLimit : Notify if data sample crosses cwrThreshValue while increasing in value. lowLimit : Notify if data sample crosses cwrThreshValue while decreasing in value.
INT cwrThroughput	1.3.6.1.4.1.9.9.136.1.3.2.1.3	INTEGER	read-write	This represents an throughput expected of the identified radio link. There are 3 possible settings. The settings provide a tradeoff between bandwidth and the reliability of the radio link. The settings are: high(1): For a high throughput. The radio hardware will be configured such that it, favors throughput over error correction. It may not be able to correct all received errors. medium(2): This is a balance between high and low. low(3): The radio hardware is configured such that it trades off throughput for latency and error correction. It tries its very best to correct errors it detects.
CWR cwrTlAction	1.3.6.1.4.1.9.9.136.1.8.2.1.11	CwrCollectionAction	read-create	This object represents the action to be carried out on this timeline specification. If a timeline has been successfully captured then it must be cleared before an other capture may be initiated.
CWR cwrTlClass	1.3.6.1.4.1.9.9.136.1.8.2.1.2	CwrRadioSignalAttribute	read-create	This object represents the attribute for which a timline capture is requested. When a timeline is requested, cwrTlNumDataValues worth of data will be captured.
cwrTlCtrlEntry	1.3.6.1.4.1.9.9.136.1.8.2.1		not-accessible	This represents one entry in the cwrTlCtrlTable. It is indexed by the ifIndex, cwrTlClass, cwrRfResourceId, cwrTlDspNum.
cwrTlCtrlTable	1.3.6.1.4.1.9.9.136.1.8.2		not-accessible	This table contains information about timelines configured in hardware. The number of data values captured for each timeline is configured by setting the variable cwrTlNumDataValues. The captured data values can be retreived by reading the cwrTlDataTable.
cwrTlDataEntry	1.3.6.1.4.1.9.9.136.1.8.4.1		not-accessible	This represents one entry in the cwrTlDataTable. It is indexed by ifIndex, cwrTlIndex, and cwrTlValueIndex.
cwrTlDataTable	1.3.6.1.4.1.9.9.136.1.8.4		not-accessible	This table contains data values collected for the timelines specified in the cwrTlCtrlTable. The number of data values displayed for each timeline is determined by the value specified for cwrTlNumDataValues in cwrTlCtrlTable.
I32 cwrTlDecimationFactor	1.3.6.1.4.1.9.9.136.1.8.2.1.6	Integer32	read-create	This object represents the number of successive data samples to be added and returned. This enables larger data sets to be captured even with limited cwrTlNumDataValues.
INT cwrTlDspNum	1.3.6.1.4.1.9.9.136.1.8.2.1.4	INTEGER	read-create	This object identifies the DSP on which this timeline needs to be captures. If 0 is specified then the agent will automatically use the most logical DSP for the specified cwrTlClass parameter. If 0 has been specified on create then on reading this object the agent will return the DSP number that is being used to capture this timeline.
I32 cwrTlIndex	1.3.6.1.4.1.9.9.136.1.8.2.1.1	Integer32	not-accessible	This object, along with ifIndex, is the index into this table and represents one entry in the table. The entry in this table for which cwrTlIndex = x is associated with the entry in cwrTlSummaryTable and the entry in cwrTlDataTable for which the index variable in those tables has the same value, x.
INT cwrTlNumDataValues	1.3.6.1.4.1.9.9.136.1.8.2.1.5	INTEGER	read-create	This object indicates the number of data values to be captured for this timeline. The captured data can be viewed by reading the cwrTlDataTable.
I32 cwrTlNumValues	1.3.6.1.4.1.9.9.136.1.8.3.1.2	Integer32	read-only	This object represents the number of values available in the timeline.
INT cwrTlPostTrigBufMgmt	1.3.6.1.4.1.9.9.136.1.8.2.1.13	INTEGER	read-create	Once a trigger fires, this object determines which portion of the collected data to capture for use. If it is: preTrigger(1) : Then most of the data collected prior to trigger is captured. postTrigger(2): Then most of the data collected after the trigger is captured.
I32 cwrTlPreSumShift	1.3.6.1.4.1.9.9.136.1.8.2.1.7	Integer32	read-create	This object represents the number of bits by which the raw data data should be right shifted before applying cwrTlDecimationFactor. This provides a mechanims of controlling overflow due to summation.
CWR cwrTlRfResourceId	1.3.6.1.4.1.9.9.136.1.8.2.1.3	CwrRFZeroIndex	read-create	This object identifies the RF resource for which this timeline specification applies. If this is 0 then the agent will automatically the most logical value for the specified cwrHistClass. If 0 has been specified then on reading this object the agent will return the RF resource id for which the timeline is being captured.
ROW cwrTlRowStatus	1.3.6.1.4.1.9.9.136.1.8.2.1.14	RowStatus	read-create	This object may be used to create or delete a timeline control specification. Once created data sampling starts based on the value of cwrTlAction. The data capture depends on the value of cwrTlThreshIndex. The actual data is collected based on the cwrTlThreshIndex, if cwrTlThreshIndex is 0 then there is no stop trigger associated with this timeline and the data samples are captured and returned immediately. If cwrTlThresIndex is not 0, then the data samples are captured when the threshold fires.
CWR cwrTlStatus	1.3.6.1.4.1.9.9.136.1.8.2.1.12	CwrCollectionStatus	read-only	This object represents the current state of this timeline collection. Once the timeline collection is complete the status changes statusCaptured and the data is available for use. None of the parameters of a timeline specification may be modified when the specification is in statusInProgress. A statusCaptured or statusStopped histogram must be actionClear'ed before another timeline specification may be started.
cwrTlSummaryEntry	1.3.6.1.4.1.9.9.136.1.8.3.1		not-accessible	This represents one entry in the cwrTlSummaryTable. It is indexed by the ifIndex and cwrTlIndex.
cwrTlSummaryTable	1.3.6.1.4.1.9.9.136.1.8.3		not-accessible	This table contains Timeline Summary collected based on the specifications in the cwrTlCtrlTable.
I32 cwrTlThreshIndex	1.3.6.1.4.1.9.9.136.1.8.2.1.10	Integer32	read-create	This object specifies the index of the threshold that when triggered will start the data capture for this timeline. For a timeline data capture to be triggered by a threshold, the threshold must be defined on the same DSP as the timeline. If cwrTlThreshIndex is 0 then there is no threshold associated with this timeline and the data samples are captured and returned immediately. If cwrTlThresIndex is not 0, then the data samples are captured when the threshold fires.
INT cwrTlToneSelection	1.3.6.1.4.1.9.9.136.1.8.2.1.8	INTEGER	read-create	This object identifies which tone in a burst should be used to sample data for the timeline. cwrCirculate(1): The successive tone will be used for every successive burst. cwrAverage(2): The value of every tone in a burst will be averaged. cwrspecific(3): The identified tone is used. DEFVAL { cwrAverage }
I32 cwrTlToneValue	1.3.6.1.4.1.9.9.136.1.8.2.1.9	Integer32	read-create	If cwrTlToneSelection is cwrSpecificTone then this object identifies the tone that should be used for sampling.
I32 cwrTlTriggerLoc	1.3.6.1.4.1.9.9.136.1.8.3.1.3	Integer32	read-only	This object contains the value of cwrTlValueIndex which represents the entry in the cwrTlDataTable that caused the stop trigger to fire, thereby resulting in this timeline to be collected.
I32 cwrTlUpdateTime	1.3.6.1.4.1.9.9.136.1.8.3.1.1	Integer32	read-only	This object represents the time in seconds since power up when this timeline capture was completed.
I32 cwrTlValue	1.3.6.1.4.1.9.9.136.1.8.4.1.2	Integer32	read-only	This object represents the radio signal data sampled.
INT cwrTlValueIndex	1.3.6.1.4.1.9.9.136.1.8.4.1.1	INTEGER	not-accessible	This object, along with ifIndex and cwrTlIndex, is the index into the timeline data table.
NTF cwrTrapConfigMismatch	1.3.6.1.4.1.9.9.136.2.2.1			The radio subsystem has detected that the combination of the configuration parameters that has been requested is inconsistent and cannot be supported. The cwrTrapReason is the textual description of what parameter causes the mismatch.
NTF cwrTrapIfRefOsc	1.3.6.1.4.1.9.9.136.2.2.8			The IF Reference Frequency oscillator has changed state.
NTF cwrTrapIfRxOsc	1.3.6.1.4.1.9.9.136.2.2.6			The IF receive frequency oscillator has changed state.
NTF cwrTrapIfTxOsc	1.3.6.1.4.1.9.9.136.2.2.7			The IF transmit frequency oscillator has changed state.
NTF cwrTrapInitFailure	1.3.6.1.4.1.9.9.136.2.2.2			The radio subsystem has failed to initialize the hardware successfully. This implies that there is a critical error condition in the associated hardware. The cwrTrapReason specifies the reason the init failed.
NTF cwrTrapLink1HrThresh	1.3.6.1.4.1.9.9.136.2.2.14			One of cwrLink1HrESAlarmThresh, cwrLink1HrSESAlarmThresh, cwrLink1HrCSESAlarmThresh, cwrLink1HrDCMAlarmThresh was was exceeded. The cwrTrapReason will identify which threshold was exceeded.
NTF cwrTrapLink24HrThresh	1.3.6.1.4.1.9.9.136.2.2.15			One of cwrLink24HrESAlarmThresh, cwrLink24HrSESAlarmThresh, cwrLink24HrCSESAlarmThresh, cwrLink24HrDCMAlarmThresh was was exceeded. The cwrTrapReason will identify which threshold was exceeded.
NTF cwrTrapLinkQuality	1.3.6.1.4.1.9.9.136.2.2.3			The radio subsystem has detected a significant change in the radio link quality. The cwrTrapReason will describe the quality.
NTF cwrTrapLinkSyncAcquired	1.3.6.1.4.1.9.9.136.2.2.5			The radio link has acquired synchronization with the remote end.
NTF cwrTrapLinkSyncLost	1.3.6.1.4.1.9.9.136.2.2.4			The radio link has lost synchronization with the remote end.
STR cwrTrapReason	1.3.6.1.4.1.9.9.136.2.1.1.1.1	DisplayString	read-only	The explanation string for the event trap cwrEventId.
NTF cwrTrapRfRxOsc	1.3.6.1.4.1.9.9.136.2.2.10			The RF receive frequency oscillator has changed state. The cwrRfIndex identifies the RF resource that is the cause of this trap. The cwrRfRxOscState specifies the state of the oscilator.
NTF cwrTrapRfStatusChange	1.3.6.1.4.1.9.9.136.2.2.13			This trap indicates that the RF resource either came online(1) or went offline(2). The cwrRfIndex will identify which resource changed state and cwrRfStatus will identify what state it is in.
NTF cwrTrapRfSupplyVoltage	1.3.6.1.4.1.9.9.136.2.2.9			The supply voltage to the RF resource has changed. The cwrRfSupplyVoltageState specifies whether the supply voltage is in spec or not.
NTF cwrTrapRfTemp	1.3.6.1.4.1.9.9.136.2.2.12			The temperature of the RF module identified by cwrRfIndex has exceeded a defined reference.
NTF cwrTrapRfTxOsc	1.3.6.1.4.1.9.9.136.2.2.11			The RF transmit frequency oscillator has changed state. The cwrRfIndex identifies the RF resource that is the cause of this trap. The cwrRfRxOscState specifies the state of the oscilator.
NTF cwrTrapThresh	1.3.6.1.4.1.9.9.136.2.3.1			The radio subsystem generates this trap when a threshold crosses its specified limit. The parameters identify the following cwrThreshValue - The value that was crossed. cwrThreshHysteresisTime - The Hysteresis time that was specified. cwrThreshLimitTime - The Limit time that was specified.
INT cwrTxFreqRangeMax	1.3.6.1.4.1.9.9.136.1.5.1.1.5	INTEGER	read-only	This object represents the maximum frequency at which this RF resource can transmit.
INT cwrTxFreqRangeMin	1.3.6.1.4.1.9.9.136.1.5.1.1.4	INTEGER	read-only	This object represents the minimum frequency at which this RF resource can transmit.
INT cwrTxFrequency	1.3.6.1.4.1.9.9.136.1.3.2.1.5	INTEGER	read-write	This object represents the center frequency that will be used to transmit data over the radio PHY. The specified transmit frequency must match the operating band and the capability of the RF resource connected to the radio.
INT cwrTxPower	1.3.6.1.4.1.9.9.136.1.3.2.1.7	INTEGER	read-write	This object represents the power that the antenna will transmit. The minimum average transmit power for the U-NII or MMDS band is 0.01 microwatts (-80 dBm). Maximum average transmit power: For the MMDS band is 2 Watts i.e. (+33dBm). For the U-NII band is 100 milliwatts i.e. (+20dBm). The power is specified in dBm.
CWR cwrTxRfIndex	1.3.6.1.4.1.9.9.136.1.3.1.1.5	CwrRFZeroIndex	read-only	This object specifies the index into the cwrRfTable identifying the antenna used for transmission. This index will be 0 if the associated transmit antenna is not present.
C32 cwrUnAvailableSeconds	1.3.6.1.4.1.9.9.136.1.6.2.1.2	Counter32	read-only	This object represents the number of seconds that the link was not available for use. It is equal to: Severely Errored Seconds + Sync Loss Seconds.
I32 cwrUpdateRate	1.3.6.1.4.1.9.9.136.1.7.1.1.8	Integer32	read-create	This object represents rate at which snapshots of the histogram will be available.
I32 cwrValue	1.3.6.1.4.1.9.9.136.1.7.3.1.2	Integer32	read-only	This object represents the value in the histogram bin cwrHistBinIndex.

RFC description

Cisco Wireless Radio Point-to-Point MIB for monitoring wireless interfaces, performance metrics, and link characteristics on Cisco wireless networking equipment.

Start monitoring Cisco wireless point-to-point radio/bridge equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-WIRELESS-IF-MIB