All MIBs › CISCO-WIRELESS-IF-MIB › cwrThroughput
cwrThroughput
Module: CISCO-WIRELESS-IF-MIB
OID (symbolic): CISCO-WIRELESS-IF-MIB::cwrThroughput
OID (numeric): 1.3.6.1.4.1.9.9.136.1.3.2.1.3
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This represents an throughput expected of the identified radio link. There are 3 possible settings. The settings provide a tradeoff between bandwidth and the reliability of the radio link. The settings are: high(1): For a high throughput. The radio hardware will be configured such that it, favors throughput over error correction. It may not be able to correct all received errors. medium(2): This is a balance between high and low. low(3): The radio hardware is configured such that it trades off throughput for latency and error correction. It tries its very best to correct errors it detects.
What is cwrThroughput?
This read-write INTEGER (high, medium, or low) represents the throughput profile the radio hardware is configured to favor, trading off raw bandwidth against error-correction reliability. An admin picks a lower throughput setting when link reliability matters more than peak data rate, such as on a marginal RF path. For example, on a link that experiences frequent retransmissions, an admin might lower cwrThroughput from high to medium to favor error correction over maximum bit rate.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.9.136.1.3.2.1.3 snmpwalk -v2c -c public <target> CISCO-WIRELESS-IF-MIB::cwrThroughput
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.9.136.1.3.2.1.3.1 snmpget -v2c -c public <target> CISCO-WIRELESS-IF-MIB::cwrThroughput.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.9.136.1.3.2.1.3.1 i <value>
Start monitoring Cisco wireless point-to-point radio/bridge equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-WIRELESS-IF-MIB::cwrThroughput OID value, configure state conditions and alerts, and monitor any Cisco wireless point-to-point radio/bridge equipment (legacy) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.9 | ciscoMgmt | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.9.136 | ciscoWirelessIfMIB | CISCO-WIRELESS-IF-MIB |
| 1.3.6.1.4.1.9.9.136.1 | cwrRadioMibObjects | CISCO-WIRELESS-IF-MIB |
| 1.3.6.1.4.1.9.9.136.1.3 | cwrRadioBaseGroup | CISCO-WIRELESS-IF-MIB |
| 1.3.6.1.4.1.9.9.136.1.3.2 | cwrRadioPhyTable | CISCO-WIRELESS-IF-MIB |
| 1.3.6.1.4.1.9.9.136.1.3.2.1 | cwrRadioPhyEntry | CISCO-WIRELESS-IF-MIB |
| 1.3.6.1.4.1.9.9.136.1.3.2.1.3 | cwrThroughput | CISCO-WIRELESS-IF-MIB |