All MIBs › CTRON-AppleTalk-ROUTER-MIB
Category: Protocol: AppleTalk, Technology: Routing, Vendor: Cabletron
Description: Manages AppleTalk routing tables, zones, and protocol statistics on Cabletron routers.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CTRON-AppleTalk-ROUTER-MIB?
CTRON-AppleTalk-ROUTER-MIB is a Cabletron Systems MIB for managing AppleTalk routing on Cabletron network routers, exposing routing tables, zone information, and protocol statistics for the legacy AppleTalk network protocol. It provides system-level status objects for the AppleTalk router process and its forwarding counter subsystem, alongside version and revision information. This MIB is used to monitor the software status of the AppleTalk routing process, with objects like nwAtSysAdminSTATUS/nwAtSysOperSTATUS indicating whether AppleTalk routing is administratively enabled and actually running, nwAtSysOperationalTime tracking process uptime, and nwAtFwdCtrInPkts providing forwarding traffic counters to detect abnormal traffic levels or a stalled forwarding process. It is a legacy vendor-specific MIB with no apparent dependency on other MIBs, tied to Cabletron's own router architecture. It was typically deployed in 1990s-era mixed AppleTalk/IP enterprise networks using Cabletron routing equipment to route AppleTalk traffic between Macintosh network segments. Network engineers evaluating or troubleshooting this functionality can download the CTRON-AppleTalk-ROUTER-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CTRON-AppleTalk-ROUTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cabletron Systems router (AppleTalk-capable)
Monitoring Examples
An operator would poll nwAtSysAdminSTATUS against nwAtSysOperSTATUS to confirm the AppleTalk routing process is both enabled and actually operational, and check nwAtSysOperationalTime to see how long it has been running since nwAtSysAdminReset. Monitoring nwAtFwdCtrInPkts alongside nwAtFwdCtrOperationalTime would reveal whether the forwarding counter subsystem is actively counting traffic or has stalled, which combined with nwAtSysVersion would help confirm the router is running expected software before troubleshooting a routing outage.
What Can Be Monitored
- AppleTalk routing admin/operational status
- router operational uptime
- forwarding counter admin status and uptime
- inbound forwarded packet counts
- router software version
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| TimeTicks |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
From ROUTER-OIDS
| nwRouter | OBJECT-IDENTITY |
| nwRtrProtoSuites | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| nwAtAccessControl | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7 | |||
| ATN nwAtAclDestZone | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.2.1.5 | AtName | read-write | Specifies the destination zone name used to compare for matches on the access control list. |
| nwAtAclEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.2.1 | not-accessible | Each entry contains AppleTalk source/destination access information. | |
| INT nwAtAclIdentifier | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.2.1.1 | INTEGER | read-only | This is the primary (major) index into the AppleTalk access control list table. Essentially, this identifies the access control list by a unique identifier (at least 1) and is arbitrarily assigned by the user. All entries that have the same ID belong to the same access control list. |
| CTR nwAtAclMatches | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.2.1.4 | Counter | read-only | Indicates the number of matches on this entry that have resulted in the access restriction permit/deny being applied as part of the forwarding process. |
| INT nwAtAclPermission | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.2.1.3 | INTEGER | read-write | Specifies whether access is allowed or denied between the source and destination address pairs. Note that source and destination are interchangeable when bi-directional control is selected. To remove an existing entry set invalid (2), and it will disappear after reboot. |
| INT nwAtAclSequence | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.2.1.2 | INTEGER | read-only | This is the secondary (minor) index into the AppleTalk access control list table. This number corresponds to a sequence number used to order multiple entries within the same access control list. |
| ATN nwAtAclSrcZone | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.2.1.6 | AtName | read-write | Specifies the source zone to be used to compare for matches on the access control list. |
| nwAtAclTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.2 | not-accessible | This table contains the Access Control List information for theAppleTalk protocol. This table contains entries, each of which allows packet forwarding between source/destination pairs to be permitted or denied. The particular list is identified by the access control list ID. Each list may contain multiple entries ordered by sequence number. When a particular access control list is searched, it is searched in sequence number order and the first match found ends the search. If no match is found, access defaults to permitted. | |
| GAU nwAtAclValidEntries | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.7.1 | Gauge | read-only | Indicates the number of valid entries that exist in the Access Control List Table. |
| nwAtComponents | 1.3.6.1.4.1.52.4.2.2.2.3.4.2 | |||
| nwAtDistanceVector | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1 | |||
| nwAtEndSystems | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6 | |||
| nwAtEvent | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10 | |||
| INT nwAtEventAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.1.1 | INTEGER | read-write | Sets the administrative state of AppleTalk event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive. |
| nwAtEventEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1.1 | not-accessible | Each entry contains the information about an event that has been logged to the event table. | |
| nwAtEventFilterEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2.1.1 | not-accessible | Each entry describes an event filter which defines a particular type of event to be logged to the event log. The value of nwIpEventProtocol indicates the value used in either the nwRtgProtocolTable or the nwComponentTable Cabletron Routing Services MIB, which indentifies the protocol to which the entry exists. | |
| nwAtEventFilterTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2.1 | not-accessible | This table contains an entry for each event filter configured for AppleTalk Routing Service's events. | |
| INT nwAtEventFltrAction | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2.1.1.6 | INTEGER | read-write | Specifies how the events are to be logged. Logging to the `log' stores the events in the event log table (nwIpEventFltrAction). Logging to `trap' sends events out through the trap mechanism. |
| INT nwAtEventFltrControl | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2.1.1.3 | INTEGER | read-write | Set this value to 3 to add the entry to the event log table. Set this value to 2 to remove the entry from the event filter table. |
| INT nwAtEventFltrIfNum | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2.1.1.2 | INTEGER | read-only | Specifies the router port involved in the event for which the event filter exists. |
| INT nwAtEventFltrProtocol | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2.1.1.1 | INTEGER | read-only | Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentRtgInstance, which identifies the protocol involved in the event for which the event filter exists. |
| INT nwAtEventFltrSeverity | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2.1.1.5 | INTEGER | read-write | Specifies the level of severity an event must meet in order to be logged. Controls the amount of event logging by ignoring events of a lower priority than specified by this filter value. `Highmed' ignores only events of the lowest severity. `Highlow' logs all events highest priority through lowest. `Highest' severity causes all events except those of the highest severity to be ignored. `Highmed' severity is the default setting which causes only events of the lowest severity to be ignored. `Highlow' severity logs all events, regardless of severity. |
| INT nwAtEventFltrType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2.1.1.4 | INTEGER | read-write | This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events are to be logged. Setting any bit to 0 removes an event type from this field and prevents that type of event from being logged. Setting any bit to 1 adds an event type to this field and enables that type of event to be logged. |
| INT nwAtEventIfNum | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1.1.6 | INTEGER | read-only | Indicates the router port that was involved in the event. |
| nwAtEventLogConfig | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.1 | |||
| nwAtEventLogFilterTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.2 | |||
| nwAtEventLogTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3 | |||
| INT nwAtEventMaxEntries | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.1.2 | INTEGER | read-write | Sets the maximum number of entries allowed in the event log table. When the number of entries reaches the value of nwAtEventMaxEntries the first (oldest) entry is deleted to allow a new entry to be added. |
| INT nwAtEventNumber | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1.1.1 | INTEGER | read-only | An ordinal value assigned to the event for which the log entry exists. nwAtEvnetNumber is assigned so that each event in the event log can be uniquely identified by the value of nwAtEventNumber. |
| INT nwAtEventProtocol | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1.1.5 | INTEGER | read-only | Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentInstance which identifies the protocol or component that was involved in the event. |
| INT nwAtEventSeverity | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1.1.4 | INTEGER | read-only | Indicates the severity that was assigned to this event. |
| nwAtEventTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1 | not-accessible | This table contains an entry for each event that has been logged. | |
| OCT nwAtEventTextString | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1.1.7 | OCTET STRING | read-only | Contains the actual text string that was logged. |
| TIK nwAtEventTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1.1.2 | TimeTicks | read-only | Indicates the time at which the event was logged to the event log |
| INT nwAtEventTraceAll | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.1.3 | INTEGER | read-write | Enabled (3) allows logging of all event types on all router ports from all protocols and components. Disabled (2) causes the event log filter table to specify which events to log. |
| INT nwAtEventType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.10.3.1.1.3 | INTEGER | read-only | Indicates the type of event that was logged. |
| nwAtFib | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5 | |||
| ATN nwAtFibEndNet | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5.1.1.2 | AtNetworkNumber | read-only | Indicates the end of the network range for the route. |
| nwAtFibEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5.1.1 | not-accessible | Each entry in the table describes an AppleTalk route to a particular destination. | |
| INT nwAtFibHops | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5.1.1.5 | INTEGER | read-only | Indicates the number of hops required to reach the destination for which the entry exists. It is considered as metric 1. |
| ADR nwAtFibNextHop | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5.1.1.3 | AtDdpNodeAddress | read-only | Indicates the full AppleTalk network address of the next hop router for the route. An address of all zeros indicates a directly connected net. |
| INT nwAtFibNextHopIf | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5.1.1.4 | INTEGER | read-only | Indicates the value of MIB 2 ifindex, which identifies the router port through which the next hop node exists. Packets destined for the network specified by the entry will be forwarded on this router port. |
| INT nwAtFibRouteType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5.1.1.6 | INTEGER | read-only | Indicates the type of route (Allows for PPP entries later). |
| ATN nwAtFibStartNet | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5.1.1.1 | AtNetworkNumber | read-only | Indicates the start of the network range for the route. |
| nwAtFibTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.5.1 | not-accessible | This table contains an entry for each route being used to forward AppleTalk data packets. | |
| nwAtFilters | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.8 | |||
| nwAtForwarding | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2 | |||
| nwAtFwdCounters | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1 | |||
| CTR nwAtFwdCtrAddrErrPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.9 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded, system-wide, during nwAtFwdCtrOperationalTime because of addressing errors in the AppleTalk header. |
| INT nwAtFwdCtrAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.1 | INTEGER | read-write | Sets the administrative state of the aggregate (system-wide) AppleTalk packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive. |
| CTR nwAtFwdCtrDiscardBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.16 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been discarded, system wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrDiscardPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.8 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded, system-wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrFilteredBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.15 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been administratively filtered, system-wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrFilteredPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.7 | Counter | read-only | Indicates the total number of AppleTalk packets that have been administratively filtered, system-wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrFwdBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.14 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been forwarded, system-wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrFwdPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.6 | Counter | read-only | Indicates the total number of AppleTalk packets that have been forwarded, system-wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrHdrErrPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.11 | Counter | read-only | Indicates the total number of at packets that have been discarded, device-wide, during nwAtFwdCtrOperationalTime, because of an invalid at header. |
| CTR nwAtFwdCtrHostDiscardBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.22 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been discarded by the local host, during nwAtFwdCtrOperationalTime, due to a lack of host resources. |
| CTR nwAtFwdCtrHostDiscardPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.19 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded by the local host, during nwAtFwdCtrOperationalTiime, due to a lack of host resources. |
| CTR nwAtFwdCtrHostInBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.20 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been received by the local host, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrHostInPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.17 | Counter | read-only | Indicates the total number of AppleTalk packets that have been successfully delivered to the local host, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrHostOutBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.21 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been transmitted by the local host, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrHostOutPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.18 | Counter | read-only | Indicates the total number of AppleTalk packets that have been transmitted by the local host, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrInBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.12 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been received, system-wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrInPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.4 | Counter | read-only | Indicates the total number of AppleTalk packets that have been received, system-wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrLenErrPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.10 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded, system-wide, during nwAtFwdCtrOperationalTime, because an invalid packet length is contained in the AppleTalk header. |
| TIK nwAtFwdCtrOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.3 | TimeTicks | read-only | Indicates the elapsed time, in hundredths of a second, that nwAtFwdCtrAdminStatus has been in the current state. |
| CTR nwAtFwdCtrOutBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.13 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been transmitted, system-wide, during nwAtFwdCtrOperationalTime. |
| CTR nwAtFwdCtrOutPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.5 | Counter | read-only | Indicates the total number of AppleTalk packets that have been transmitted, system-wide, during nwAtFwdCtrOperationalTime. |
| INT nwAtFwdCtrReset | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1.1.2 | INTEGER | read-write | Reset(2) resets the aggregate (system-wide) AppleTalk packet and byte counters. Reset (2) resets the AppleTalk aggregate counters to 0.nwAtFwdCtrOperationalTime is also reset to 0. |
| INT nwAtFwdIfAclIdentifier | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.9 | INTEGER | read-write | Specifies the Access Control ID of the access control list in effect for AppleTalk packets being routed on the router port for which the entry exists. A value of 0 indicates that no access control list is in effect. |
| INT nwAtFwdIfAclSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.10 | INTEGER | read-write | Controls the operation of any access control list configured for AppleTalk traffic on the router port for which the entry exists. Enabled (3) applies the access control list indicated by the value of nwAtFwdIfAclIdentifier to all AppleTalk traffic being routed on the port. Disabled (2) prevents the access control list from being applied. |
| INT nwAtFwdIfAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.2 | INTEGER | read-write | Sets the administrative state of AppleTalk Routing Services on the router port for which the entry exists. Enabled (3) causes AppleTalk Routing Services to become active. Disabled (2) causes it to become inactive. |
| INT nwAtFwdIfCacheControl | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.11 | INTEGER | read-write | Controls AppleTalk Address caching on the router port for which the entry exists. When AppleTalk Address caching is enabled, AppleTalk Addresses used for address validation, filtering, and forwarding are stored in the cache. This cache is checked first before doing a full route table lockup, which speeds up the switching process. Enabled (3) turns on AppleTalk Address caching. Disabled (2) turns it off. |
| CTR nwAtFwdIfCacheEntries | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.12 | Counter | read-only | Indicates the number of entries in the AppleTalk Address cache on the router port for which the entry exists. |
| CTR nwAtFwdIfCacheHits | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.13 | Counter | read-only | Indicates the number of times entries in the AppleTalk Address cache have been used to provide the AppleTalk address required to validate, filter, or forward an AppleTalk packet on the router port. |
| CTR nwAtFwdIfCacheMisses | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.14 | Counter | read-only | Indicates the number of times the AppleTalk Address required to validate, filter, or forward an AppleTalk packet on the router port was not found in the AppleTalk Address cache. |
| nwAtFwdIfConfig | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1 | |||
| INT nwAtFwdIfControl | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.5 | INTEGER | read-write | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect. |
| nwAtFwdIfCounters | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2 | |||
| CTR nwAtFwdIfCtrAddrErrPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.10 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded, because of addressing errors in the AppleTalk header, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| INT nwAtFwdIfCtrAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.2 | INTEGER | read-write | Sets the administrative state of the per-port AppleTalk packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive. |
| CTR nwAtFwdIfCtrDiscardBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.17 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been discarded, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrDiscardPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.9 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded (dropped), during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| nwAtFwdIfCtrEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1 | not-accessible | Each entry indicates the current packet and byte count of AppleTalk packets on the router port for which the entry exists. | |
| CTR nwAtFwdIfCtrFilteredBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.16 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been administratively filtered, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrFilteredPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.8 | Counter | read-only | Indicates the total number of AppleTalk packets that have been administratively filtered, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrFwdBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.15 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been forwarded, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrFwdPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.7 | Counter | read-only | Indicates the total number of AppleTalk packets that have been forwarded, during nwAtFwdIfCtrOperationaltime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrHdrErrPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.12 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded, because of an invalid AppleTalk header, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrHostDiscardBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.23 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been discarded by the local host, due to a lack of host resources during nwAtFwdIfCtrOperationalTime, that were received on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrHostDiscardPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.20 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded by the local host due to a lack of host resources during nwAtFwdIfCtrOperationalTime, that were received on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrHostInBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.21 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been successfully delivered to the local host, during nwAtFwdIfCtrOperationalTime, that were received on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrHostInPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.18 | Counter | read-only | Indicates the total number of AppleTalk packets that have been successfully delivered to the local host during nwAtFwdIfCtrOperationalTime, that were received on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrHostOutBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.22 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been transmitted by the local host, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrHostOutPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.19 | Counter | read-only | Indicates the total number of AppleTalk packets that have been transmitted by the local host, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| INT nwAtFwdIfCtrIfIndex | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.1 | INTEGER | read-only | Indicates the value MIB 2 ifindex, which identifies the router port for which the entry exists. |
| CTR nwAtFwdIfCtrInBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.13 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been received, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrInPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.5 | Counter | read-only | Indicates the total number of AppleTalk packets that have been received, during nwAtFwdIfCtrOperationaltime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrLenErrPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.11 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded, because an invalid packet length was contained in the AppleTalk header, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| TIK nwAtFwdIfCtrOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.4 | TimeTicks | read-only | Indicates the amount of time, in hundredths of a second, that nwAtFwdIfCtrAdminStatus has been in the current state. |
| CTR nwAtFwdIfCtrOutBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.14 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been transmitted, durin nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| CTR nwAtFwdIfCtrOutPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.6 | Counter | read-only | Indicates the total number of AppleTalk packets that have been transmitted, during nwAtFwdIfCtrOperationaltime, on the router port for which the entry exists. |
| INT nwAtFwdIfCtrReset | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1.1.3 | INTEGER | read-write | Resets the per-port AppleTalk packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwAtFwdIfCtrOperationalTime is also reset to 0. |
| nwAtFwdIfCtrTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.2.1 | not-accessible | This table contains an entry for each router port configured and enabled for AppleTalk Routing Services. | |
| nwAtFwdIfEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1 | not-accessible | Each entry specifies the AppeTalk Routing Services configuration for the router port for which the entry exists. | |
| INT nwAtFwdIfForwarding | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.7 | INTEGER | read-write | Controls forwarding of AppleTalk packets on the AppleTalk router port for which the entry exists. Enabled (3) causes AppleTalk packets to be forwarded. Disabled (2) prevents AppleTalk packets from being forwarded. |
| INT nwAtFwdIfFrameType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.8 | INTEGER | read-write | Specifies the framing type for AppleTalk packets forwarded on the router port for which the entry exists. Some frame types are only valid for specific media types. The comments reflect those valid media types. |
| INT nwAtFwdIfIndex | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.1 | INTEGER | read-only | Indicates the value of the MIB 2 ifIndex, which identifies the router port for which the entry exists. |
| INT nwAtFwdIfMtu | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.6 | INTEGER | read-write | Specifies the Maximum Transmissions Unit (MTU) for AppleTalk packets on the router port for which the entry exists. This includes the AppleTalk header and data, but does not include framing. |
| TIK nwAtFwdIfOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.4 | TimeTicks | read-only | Indicates the elapsed time, in hundredths of a second, that nwAtFwdIfOper Status has been in its current state. |
| INT nwAtFwdIfOperSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1.1.3 | INTEGER | read-only | Indicates the current operating condition of AppleTalk Routing Services on the AppleTalk router port for which the entry exists. The value of nwAtFwdIfOperStatus indicates any problem with the configuration of AppleTalk Routing Services on the router port. A value of 6 indicates that regardless of the state of nwAtFwdIfAdminStatus AppleTalk Routing Services is not operating because of an invalid port-level configuration. |
| nwAtFwdIfTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.1 | not-accessible | This table contains an entry for each router port. This table is indexed by nwAtFwdIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which each entry exists. | |
| nwAtFwdInterfaces | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2 | |||
| nwAtFwdSystem | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.1 | |||
| INT nwAtHostCtlAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.2 | INTEGER | read-write | Sets the administrative state of the AARP cache on the router port for which the entry exists. Enabled (3) causes AARP caching to become active. Disabled (2) causes AARP caching to perform a graceful shutdown. |
| CTR nwAtHostCtlCacheHits | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.12 | Counter | read-only | Indicates the number of times an entry in the AARP cache has been used to successfully provide the physical address required to forward an AppleTalk packet on the router port for which the entry exists. |
| INT nwAtHostCtlCacheMax | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.8 | INTEGER | read-write | Indicates the maximum number of entry slots the AARP cache can consist of. nwAtHostCtlCacheMax cannot be set to less than 16. Setting this value does not allocate any memory for the cache. |
| CTR nwAtHostCtlCacheMisses | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.13 | Counter | read-only | Indicates the number of times the physical address required to forward an AppleTalk packet has not been found in the AARP cache on the router port for which the entry exists. |
| INT nwAtHostCtlCacheSize | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.9 | INTEGER | read-write | Indicates the current number of entry slots in the AARP cache on the router port for which the entry exists. The cache automatically resizes to accommodate all entries up to the maximum number of entries set by nwAtHostCtlCacheMax. |
| nwAtHostCtlEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1 | not-accessible | Each entry contains the control information for the ARP cache on the router port indicated by the value nwAtHostCtlIfIndex. | |
| INT nwAtHostCtlIfIndex | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.1 | INTEGER | read-only | Indicates the value of MIB2 ifindex, which identifies the router port for which the entry exists. |
| CTR nwAtHostCtlNumDynamics | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.11 | Counter | read-only | Indicates the number of dynamic entries in the AARP cache on the router port for which the entry exists. Dynamic entries area added and aged out by the AARP protocol. |
| CTR nwAtHostCtlNumStatics | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.10 | Counter | read-only | Indicates the total number of static entries in the AARP cache on the router port for which the entry exists. Static entries remain in the cache until they are administratively removed. |
| TIK nwAtHostCtlOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.4 | TimeTicks | read-only | Indicates the amount of time, in hundredths of a second, that nwAtHostCtlOperStatus has been in the current state. |
| INT nwAtHostCtlOperSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.3 | INTEGER | read-only | Indicates the current operating condition of the AARP Table on the router port for which the entry exists. |
| INT nwAtHostCtlProtocol | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.5 | INTEGER | read-write | Controls the operation of the AARP protocol on the router port for which the entry exists. |
| INT nwAtHostCtlProxy | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.7 | INTEGER | read-write | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect. |
| INT nwAtHostCtlSnooping | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1.1.6 | INTEGER | read-write | Controls AARP Snooping on the router port for which the entry exists. Given the AARP protocol is enabled, setting nwAtHostCtlIfSnooping to enabled (3) turns on AARP Snooping. When AARP Snooping is enabled the source AppleTalk and physical addresses of all AARP packets received on the router port are added to the AARP Table. |
| nwAtHostCtlTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2.1 | not-accessible | This table contains the control information for maintaining an AARP cache on each router port. Note that the cache entries are maintained by theAppleTalk Address Resolution Protocol Table of the AppleTalk MIB. | |
| ADR nwAtHostMapAtAddr | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1.1.2 | AtDdpNodeAddress | read-only | The AtDdpNodeAddress corresponding to the media-dependent 'physical' address and circuit identifier (if applic). |
| INT nwAtHostMapCircuitID | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1.1.5 | INTEGER | read-write | The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the IP Address at the end of the circuit. For non-WAN interfaces, the value of this object is zero. |
| nwAtHostMapEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1.1 | not-accessible | Each entry contains one AtNetworkNumber to 'physical' address equivalence, including a circuit identifier if applicable. Also provided is the framing and port number required to converse with this host. | |
| INT nwAtHostMapFraming | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1.1.6 | INTEGER | read-write | Specifies the framing type required to converse with the host for which this entry exists. |
| INT nwAtHostMapIfIndex | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1.1.1 | INTEGER | read-only | This is the primary (major) index into the HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the IP router port for which the entry exists. |
| PHY nwAtHostMapPhysAddr | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1.1.3 | PhysAddress | read-write | The media-dependent 'physical' address. The value of this object is 0 for entries indicating native-wan(8) framing. |
| INT nwAtHostMapPortNumber | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1.1.7 | INTEGER | read-only | The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of interfaces in the system and the number of circuits present on interfaces which are of WAN type. |
| nwAtHostMapTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1 | not-accessible | The Ip Address translation table used for mapping an IP address to physical address, framing, port and circuit identifier, if applicable. | |
| INT nwAtHostMapType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3.1.1.4 | INTEGER | read-write | Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwAtHostMapTable. That is, it effectively dissasociates the circuit identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant nwAtHostMapType object. |
| nwAtHostsInterfaces | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.2 | |||
| CTR nwAtHostsRetryCount | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.1.2 | Counter | read-only | Indicates the maximum number of times AppleTalk Routing Services will retry each attempt to resolve a host address. |
| nwAtHostsSystem | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.1 | |||
| INT nwAtHostsTimeToLive | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.1.1 | INTEGER | read-only | Indicates the amount of time (in minutes) that an entry can remain in the AARP cache. |
| nwAtHostsToMedia | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.6.3 | |||
| nwAtLinkState | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.2 | |||
| STR nwAtMibRevText | 1.3.6.1.4.1.52.4.2.2.2.3.4.1.1 | DisplayString | read-only | Indicates the current revision level of the Cabletron at Routing Services MIB in textual format. |
| nwAtMibs | 1.3.6.1.4.1.52.4.2.2.2.3.4.1 | |||
| nwAtNetDiag | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12 | |||
| nwAtNetDiagOutbound | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3 | |||
| INT nwAtNetDiagOutboundATEchoStatus | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.6 | INTEGER | read-write | The current status of the echo diagnostic. |
| INT nwAtNetDiagOutboundATEchoType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.5 | INTEGER | read-write | The type of echo diagnostic function to initiate. Upon setting this to send EchoRequest (2), an echo request will be initiated and the value will be set to noAction (1). |
| ATN nwAtNetDiagOutboundNBPEntityObject | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.7 | AtName | read-write | The entity object or wildcard object used in the NBP lookup diagnostic. |
| ATN nwAtNetDiagOutboundNBPEntityType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.8 | AtName | read-write | The entity type or wildcard type used in the NBP lookup diagnostic. |
| ATN nwAtNetDiagOutboundNBPEntityZone | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.9 | AtName | read-write | The entity zone used in the NBP lookup diagnostic. |
| INT nwAtNetDiagOutboundNBPStatus | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.11 | INTEGER | read-write | Indicates the current status of the outbound NBP diagnostic. |
| INT nwAtNetDiagOutboundNBPType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.10 | INTEGER | read-write | Specifies the type of outbound NBP diagnostic function to initiate. Upon setting this value to any value other than noAction (1) or other (10), the corresponding request will be made and the value will be set to noAction (1). |
| ADR nwAtNetDiagOutboundNetAddress | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.1 | AtDdpNodeAddress | read-write | The AppleTalk Network Address of a node with which the diagnostic test will directly correspond. |
| INT nwAtNetDiagOutboundPort | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.2 | INTEGER | read-write | An integer representing the port through which the diagnostic test will broadcast or multicast packets. |
| INT nwAtNetDiagOutboundRetries | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.4 | INTEGER | read-write | An integer representing the number of times a request will be repeated before failure. |
| ATN nwAtNetDiagOutboundRTMPNetEnd | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.15 | AtNetworkNumber | read-write | The end of the network range from the last successful outbound RTMP request or route data request. |
| ATN nwAtNetDiagOutboundRTMPNetStart | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.14 | AtNetworkNumber | read-write | The start of the network range from the last successful outbound RTMP request or route data request. |
| INT nwAtNetDiagOutboundRTMPStatus | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.13 | INTEGER | read-write | The current status of the outbound RTMP diagnostic. |
| INT nwAtNetDiagOutboundRTMPType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.12 | INTEGER | read-write | The type of outbound RTMP diagnostic function to initiate. Upon setting this value to a value other than noAction(1) or other(8), the corresponding request will be initiated and the value will be set to noAction(1). |
| INT nwAtNetDiagOutboundTimeout | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.3 | INTEGER | read-write | An integer representing the number of seconds before a diagnostic request will time out. |
| ATN nwAtNetDiagOutboundZIPGetNetInfoDefaultZone | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.24 | AtName | read-write | The default zone name from the last successful ZIP get-net-info request. |
| OCT nwAtNetDiagOutboundZIPGetNetInfoMulticast | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.23 | OCTET STRING | read-write | The data-link multicast address from the last successful ZIP get-net-info request. |
| ATN nwAtNetDiagOutboundZIPGetNetInfoNetEnd | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.22 | AtNetworkNumber | read-write | The end of the network range from the last successful ZIP get-net-info request. |
| ATN nwAtNetDiagOutboundZIPGetNetInfoNetStart | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.21 | AtNetworkNumber | read-write | The start of the network range from the last successful ZIP get-net-info request. |
| ATN nwAtNetDiagOutboundZIPGetNetInfoZone | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.20 | AtName | read-write | The zone name to be used in a ZIP get-net-info request diagnostic. |
| ATN nwAtNetDiagOutboundZIPQueryNet | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.18 | AtNetworkNumber | read-write | The start of the network range to send ZIP query for. |
| ATN nwAtNetDiagOutboundZIPQueryZone | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.19 | AtName | read-write | The first zone from the last successful ZIP query. |
| INT nwAtNetDiagOutboundZIPStatus | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.17 | INTEGER | read-write | The current status of the outbound ZIP diagnostic. |
| INT nwAtNetDiagOutboundZIPType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.3.16 | INTEGER | read-write | The type of outbound ZIP diagnostic function to initiate. Upon setting this value to a value other than noAction(1) or other(8), the corresponding request will be initiated and the value will be set to noAction(1). |
| nwAtNetDiagPing | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.1 | |||
| nwAtNetDiagTelnet | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.12.2 | |||
| OCT nwAtportConflictPhysAddr | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.18 | OCTET STRING | read-only | Indicates the link-layer address of the device which caused nwAtportStatus to be set to off (3). If this address is not available, or if nwAtportStatus is not set to off, this object will be a zero length octet string. |
| ATN nwAtportCurrentZone | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.17 | AtName | read-write | Specifies the current zone name for the port. In general, this is the zone name in which services on the port will be registered. If the port is not a native AppleTalk port, this object will contain an octet string of zero length. |
| STR nwAtportDescr | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.2 | DisplayString | read-write | This text string provides a description of the port to the end-user; it must not contain anything but printable ASCII characters. |
| nwAtportEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1 | not-accessible | Each entry specifies the AppleTalk address information for the router port for which the entry exists. | |
| INT nwAtportHome | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.16 | INTEGER | read-only | The value of nwAtportHome indicates whether or not the AppleTalk Routing Services-enabled device, the routing entity, is `homed' on the port for which the entry exists. If the entity is homed on the port, then it could perform NBP (Name Binding Protocol) registrations for services that it chooses to advertise. |
| INT nwAtportIfIndex | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.11 | INTEGER | read-write | Indicates the value of MIB 2 ifIndex, which identifies the router port for which the entry exists. |
| INT nwAtportIndex | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.1 | INTEGER | read-only | Indicates a unique value for each router port. The value of nwAtportIndex is an integer between 1 and the total number of ports configured for AppleTalk Routing Services. |
| CTR nwAtportInPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.14 | Counter | read-only | The total number of AppleTalk packets received on the port. |
| ADR nwAtportNetAddress | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.6 | AtDdpNodeAddress | read-write | The AppleTalk node number configured for the port. This value may be used as a hint for an initial node number used during node-finding. If the port is not a native AppleTalk port, this object shall have the value of three octets of zero. |
| INT nwAtportNetConfig | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.8 | INTEGER | read-write | Specifies the network configuration type of the port. If the port is not a native AppleTalk port, this object will have an unconfigured (4) value. |
| ATN nwAtportNetEnd | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.5 | AtNetworkNumber | read-write | The last AppleTalk network address in the network range configured for the port. If the network to which this AppleTalk port is connected is a non-extended network, or if it is not a native AppleTalk port, the value for nwAtportNetEnd will be two octets of zero. Set this value to the last network address in the network range configured for the port. |
| ADR nwAtportNetFrom | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.12 | AtDdpNodeAddress | read-only | When nwAtportNetConfig is set to garnered (2), this variable contains the DDP address of the entity from which the AppleTalk network number was garnered. When nwAtportNetConfig is set to conflictOrientedSeed (1), conflictAverseSeed (5), or softSeed (6), this variable contains the DDP address of an entity which supplied or confirmed the AppleTalk network number. If nwAtportNetConfig is set to guessed (3) or unconfigured (4), or if the AppleTalk Routing Services-enabled device has not received any network number confirmation, this object will be set to three octets of zero. |
| ATN nwAtportNetStart | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.4 | AtNetworkNumber | read-write | The first AppleTalk network address in the network range configured for the port. If the port is not a native AppleTalk port, this object will have the value of two octets of zero. Set this value to the first network address in the network range configured for the port. |
| CTR nwAtportOutPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.15 | Counter | read-only | The total number of AppleTalk packets transmitted on the port. |
| INT nwAtportSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.7 | INTEGER | read-write | Indicates the current state of the router port's AppleTalk configuration. If either nwAtportNetConfig or nwApportZoneConfig are set to (5), conflictAverseSeed, and either the configured network number range or zone name seeded by the port conflict with the settings of a neighbor router, nwApPortStatus will have a value of (6), offDueToConflict. |
| nwAtportTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2 | not-accessible | This table contains an entry for each router port configured for AppleTalk Routing Services. | |
| INT nwAtportType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.3 | INTEGER | read-write | The value of nwArPortType indicates which link-layer protocol is running immediately below DDP in the protocol stack on the router port for which the entry exists. The value of nwAtPortType determines the format of address octet stings throughout the entire AppleTalk MIB. |
| INT nwAtportZoneConfig | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.9 | INTEGER | read-write | Specifies the zone information configuration type of the port. If the port is not a native AppleTalk port, this object will have an unconfigured (4) value. |
| ATN nwAtportZoneDefault | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.10 | AtName | read-write | Specifies the name of the default zone for the port. If the port only has one zone, that zone is represented here. If the port is not a native AppleTalk port, this object will contain an octet string of zero length. |
| nwAtportZoneEntry | 1.3.6.1.4.1.52.4.2.2.2.4.1.1 | not-accessible | An entry of zone information for a port. | |
| ADR nwAtportZoneFrom | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.2.2.1.2.1.13 | AtDdpNodeAddress | read-only | When nwAtportZoneConfig is set to garnered (2), this variable contains the DDP address of the entity from which the AppleTalk Zone List was garnered. When nwAtportZoneConfig is set to conflictOrientedSeed (1), conflictAverseSeed (5), or softSeed (6), this variable contains the DDP address of an entity which supplied or confirmed the AppleTalk zone information. If nwAtportZoneConfig is set to guessed (3) or unconfigured (4), or if the AppleTalk Routing Services-enabled device has not received any zone confirmation, this object will be set to three octets of zero. |
| ATN nwAtportZoneName | 1.3.6.1.4.1.52.4.2.2.2.4.1.1.2 | AtName | read-only | A zone name configured for the AppleTalk port referred to in the corresponding entry of nwAtportZonePort. When this value is changed in a router, the router must send a zipNotify packet on the associated network. |
| INT nwAtportZonePort | 1.3.6.1.4.1.52.4.2.2.2.4.1.1.1 | INTEGER | read-only | An integer representing the port to which this zone belongs. The port identified by a particular value of this object is the same port as identified by the same value of nwAtportIndex. |
| INT nwAtportZoneStatus | 1.3.6.1.4.1.52.4.2.2.2.4.1.1.3 | INTEGER | read-write | The status of this zone entry. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwAtportZoneTable. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive from agents tabular information corresponding to entries not currently in use. Proper interpretation of such entries requires examination of the relevant nwAtportZoneStatus object. |
| nwAtportZoneTable | 1.3.6.1.4.1.52.4.2.2.2.4.1 | not-accessible | The table of zone information for non-default zones on ports. | |
| nwAtProto | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1 | |||
| INT nwAtProtoAdminReset | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.3 | INTEGER | read-write | Resets the routing protocol. Reset (2) forces a system-wide restart of the protocol without a graceful shutdown on any active router ports. |
| INT nwAtProtoAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.1 | INTEGER | read-write | Sets the administrative state of the AppleTalk distance-vector based routing protocol system-wide. Enabled (3) causes the routing protocol to become active on all router ports configured and enabled for AppleTalk Routing Services. Disabled (2) causes the routing protocol to become inactive. |
| INT nwAtProtoAgeOut | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.9 | INTEGER | read-write | Specifies the amount of time (in seconds) an inactive entry will be allowed to remain in the AppleTalk routing protocol routing table, before it is deleted, or aged-out. |
| nwAtProtoConfig | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1 | |||
| nwAtProtoCounters | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2 | |||
| INT nwAtProtoCtrAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.1 | INTEGER | read-write | Sets the administrative state of the aggregate (system-wide) AppleTalk routing protocol packet and byte counters. Enabled (3)causes these counters to become active. Disabled (2) causes these counters to be come inactive. |
| CTR nwAtProtoCtrDiscardBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.11 | Counter | read-only | Indicates the total number of bytes in the AppleTalk routing protocol packets that have been discarded, system-wide during nwAtProtoCtrOperationalTime. |
| CTR nwAtProtoCtrDiscardPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.7 | Counter | read-only | Indicates the total number of AppleTalk routing protocol packets that have been discarded, system-wide, during nwAtProtoCtrOperationalTime. |
| CTR nwAtProtoCtrFilteredBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.10 | Counter | read-only | Indicates the total number of bytes in the AppleTalk routing protocol packets that have been administratively filtered, system-wide, during nwAtProtoCtrOperationalTime. |
| CTR nwAtProtoCtrFilteredPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.6 | Counter | read-only | Indicates the total number of AppleTalk routing protocol packets that have been administratively filtered, system-wide, during nwAtProtoCtrOperationalTime. |
| CTR nwAtProtoCtrInBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.8 | Counter | read-only | Indicates the total number of bytes in the AppleTalk routing protocol packets that have been received, system-wide, during nwAtProtoCtrOperationalTime. |
| CTR nwAtProtoCtrInPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.4 | Counter | read-only | Indicates the total number of AppleTalk routing protocol packets that have been received, system-wide, during nwAtProtoCtrOperationalTime. |
| TIK nwAtProtoCtrOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.3 | TimeTicks | read-only | Indicates the elapsed time, in hundreds of seconds, that nwAtProtoCtrAdminStatus, has been in the current administrative state. |
| CTR nwAtProtoCtrOutBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.9 | Counter | read-only | Indicates the total number of bytes in the AppleTalk routing protocol packets that have been transmitted, system-wide, during nwAtProtoCtrOperationalTime. |
| CTR nwAtProtoCtrOutPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.5 | Counter | read-only | Indicates the total number of AppleTalk routing protocol packets that have been transmitted, system-wide, during nwAtProtoCtrOperationalTime. |
| INT nwAtProtoCtrReset | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.2.2 | INTEGER | read-write | Resets the aggregate (system-wide) AppleTalk distance-vector based routing protocol packet and byte counters. Reset (2) resets the AppleTalk aggregate counters to 0. nwAtProtoCtrOperationalTime is also reset to 0. |
| INT nwAtProtoDatabaseThreshold | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.8 | INTEGER | read-write | Specifies the run-time maximum number of entries that can be held in the AppleTalk routing protocol route table. |
| INT nwAtProtoHoldDown | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.10 | INTEGER | read-write | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect. |
| INT nwAtProtoIfAclIdentifier | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.16 | INTEGER | read-write | Specifies the Access Control List ID of the access control list in effect for AppleTalk routing protocol packets on the router port for which the entry exists. A value of 0 indicates that there is no access control list in effect for AppleTalk routing protocol packets on the router port. |
| INT nwAtProtoIfAclSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.17 | INTEGER | read-write | Controls the operation of the access control list identified by nwAtProtoIfAclIdentifier. Enabled (3) causes the access control list to be applied to all AppleTalk routing protocol packet traffic on the router port for which the entry exists. Disabled (2) prevents the access control list from being applied. |
| INT nwAtProtoIfAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.2 | INTEGER | read-write | Sets the administrative state of the AppleTalk routing protocol on the router port for which the entry exists. Enabled (3) causes the routing protocol to become active on the router port. Disabled (2) causes it to become inactive. |
| INT nwAtProtoIfAdvertisement | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.6 | INTEGER | read-write | This specifies the periodic interval (in seconds) that the AppleTalk routing protocol agent will advertise routes on this DECnet routing port. |
| nwAtProtoIfConfig | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1 | |||
| nwAtProtoIfCounters | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2 | |||
| INT nwAtProtoIfCtrAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.2 | INTEGER | read-write | Sets the administrative state of the AppleTalk packet and byte counters on the router port for which the entry exists. enabled(3) causes these counters to become active on the configured AppleTalk router port. disabled(2) causes these counters to become inactive on the configured AppleTalk router port. |
| CTR nwAtProtoIfCtrDiscardBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.12 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been discarded, that were received on the router port for which the entry exists, during nwAtIfCtrOperationalTime. |
| CTR nwAtProtoIfCtrDiscardPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.8 | Counter | read-only | Indicates the total number of AppleTalk packets that have been discarded, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime. |
| nwAtProtoIfCtrEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1 | not-accessible | Each entry specifies the DECnet Phase IV packet and byte counters on a per router port basis. | |
| CTR nwAtProtoIfCtrFilteredBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.11 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been administratively filtered, that were received on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime. |
| CTR nwAtProtoIfCtrFilteredPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.7 | Counter | read-only | Indicates the total number of AppleTalk packets that have been administratively filtered, on the router port for which this entry exists, during nwAtProtoIfCtrOperationalTime. |
| INT nwAtProtoIfCtrIfIndex | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.1 | INTEGER | read-only | This is the primary index into the AppleTalk interface counter table. This number corresponds to the index into the mib2 InterfaceTable which describes the router port for which the entry exists. |
| CTR nwAtProtoIfCtrInBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.9 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been received, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime. |
| CTR nwAtProtoIfCtrInPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.5 | Counter | read-only | Indicates the total number of AppleTalk packets that have been received, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime. |
| TIK nwAtProtoIfCtrOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.4 | TimeTicks | read-only | Indicates the amount of time (No. of time ticks) that the interface-specific AppleTalk packet and byte counters have been active on the router port for which the entry exists. |
| CTR nwAtProtoIfCtrOutBytes | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.10 | Counter | read-only | Indicates the total number of bytes in the AppleTalk packets that have been forwarded, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime. |
| CTR nwAtProtoIfCtrOutPkts | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.6 | Counter | read-only | Indicates the total number of AppleTalk packets that have been forwarded, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime. |
| INT nwAtProtoIfCtrReset | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1.1.3 | INTEGER | read-write | Resets the AppleTalk packet and byte counters on the router port for which the entry exists. reset (2) resets the interface-specific counters to 0. nwAtProtoIfCtrOperationalTime is also reset to 0. |
| nwAtProtoIfCtrTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.2.1 | not-accessible | This table contains the AppleTalk packet and byte counters for each router port on this device. | |
| nwAtProtoIfEntry | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1 | not-accessible | Each entry contains the AppleTalk routing protocol configuration for the router port for which the entry exists. | |
| INT nwAtProtoIfFloodDelay | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.7 | INTEGER | read-write | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol specific MIBs. Setting this object has no effect |
| INT nwAtProtoIfHelloTimer | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.10 | INTEGER | read-write | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol specific MIBs. Setting this object has no effect. |
| INT nwAtProtoIfIndex | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.1 | INTEGER | read-only | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| TIK nwAtProtoIfOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.4 | TimeTicks | read-only | Indicates the elapsed time, in hundreds of seconds, that nwAtProtoIfOperStatus has been in the current state. |
| INT nwAtProtoIfOperSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.3 | INTEGER | read-only | Indicates the current operating condition of the AppleTalk routing protocol on the router port for which the entry exists. The value of nwAtProtoIfOperStatus indicates any problem with your AppleTalk routing protocol configuration on the router port. A value of 6 indicates that regardless of the value of nwAtProtoIfAdminStatus, the routing protocol is not operating on the router port because of an invalid configuration. |
| INT nwAtProtoIfPoisonReverse | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.12 | INTEGER | read-write | Sets the operating condition of Poison Reverse on the router port for which the entry exists. When Poison Reverse is enabled, the AppleTalk routing protocol advertises any downed routes as unreachable during the period of time that it must wait before removing the route from the route table. |
| INT nwAtProtoIfPriority | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.9 | INTEGER | read-write | Sets the priority of the AppleTalk routing protocol on the router port for which the entry exists. |
| INT nwAtProtoIfRequestDelay | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.8 | INTEGER | read-write | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol specific MIBs. Setting this object has no effect. |
| INT nwAtProtoIfSnooping | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.13 | INTEGER | read-write | Controls the operation of AppleTalk routing protocol Snooping on the router port. When AppleTalk routing protocol Snooping is enabled, the routing protocol operates in passive mode, so that it receives route information, builds and maintains a route table, but does not advertise or send updates on the router port for which the entry exists. |
| INT nwAtProtoIfSplitHorizon | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.11 | INTEGER | read-write | Sets the operating condition of Split Horizon on the router port for which the entry exists. When Split Horizon is enabled, the AppleTalk routing protocol keeps track of which router port route information is received on, and prevents information about a route form being sent back out the same router port it was received on. |
| nwAtProtoIfTable | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1 | not-accessible | This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwAtProtoIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. | |
| INT nwAtProtoIfType | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.14 | INTEGER | read-write | Indicates whether the directly connected network segment does or does not support broadcast media access. If broadcast media access is supported, AppleTalk routing protocol advertisements are sent out one broadcast packet per port. If broadcast media is not supported, AppleTalk routing protocol advertisements are sent to each neighbor. |
| INT nwAtProtoIfVersion | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.5 | INTEGER | read-write | Indicates the revision level of AppleTalk routing protocol firmware on the router port for which the entry exists, in textual format. |
| INT nwAtProtoIfXmitCost | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2.1.1.1.15 | INTEGER | read-write | Sets the cost of transmitting a packet on the network segment connected to router port for which the entry exists. |
| nwAtProtoInterface | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.2 | |||
| TIK nwAtProtoOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.4 | TimeTicks | read-only | Indicates the elapsed time, in hundredths of a second, that nwAtProtoOperStatus has been in the current state. |
| INT nwAtProtoOperSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.2 | INTEGER | read-only | Indicates the current operating condition of the AppleTalk Routing Services distance-vector-based routing protocol, system-wide. The value of nwAtProtoOperStatus indicates any problem with the routing protocol configuration. A value of 6 indicates that regardless of the value of nwAtProtoAdminStatus, the routing protocol is not operating because of an invalid configuration. |
| INT nwAtProtoStackSize | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.6 | INTEGER | read-write | Specifies the stack size of the AppleTalk routing protocol thread. In order for a change of this value to take effect, the protocol (nwAtProtoAdminReset), AppleTalk Routing Services (nwAtProtoAdminReset), or the device running Routing Services must be reset. |
| nwAtProtoSystem | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1 | |||
| INT nwAtProtoThreadPriority | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.7 | INTEGER | read-write | Specifies the run-time execution priority of the AppleTalk routing protocol thread. In order for a change of this value to take effect, the AppleTalk protocol (nwAtProtoAdminReset), AppleTalk Routing Services (nwAtProtoAdminReset), or the device running Routing Services must be reset. |
| STR nwAtProtoVersion | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4.1.1.1.1.5 | DisplayString | read-only | Indicates the current revision level of the AppleTalk routing protocol firmware, in textual format. |
| nwAtRedirector | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.9 | |||
| nwAtRouter | 1.3.6.1.4.1.52.4.2.2.2.3.4 | |||
| nwAtSysAdministration | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1.2 | |||
| INT nwAtSysAdminReset | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1.2.3 | INTEGER | read-write | Resets AppleTalk Routing Services system-wide. Reset (2) forces a restart of AppleTalk Routing Services without a graceful shutdown on any active router ports and without affecting any other routing services. |
| INT nwAtSysAdminSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1.2.1 | INTEGER | read-write | Sets the administrative state of AppleTalk Routing Services system wide. Enabled (3) causes AppleTalk Routing Services to become active on all router ports configured and enabled for AppleTalk Routing Services. Disabled (2) causes AppleTalk Routing Services to become inactive system-wide. |
| nwAtSysConfig | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1.1 | |||
| TIK nwAtSysOperationalTime | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1.2.4 | TimeTicks | read-only | Indicates the elapsed time, in hundredths of a second, that nwAtSysOperStatus has been in its current state. |
| INT nwAtSysOperSTATUS | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1.2.2 | INTEGER | read-only | Indicates the operating condition of AppleTalk Routing Services system- wide. The value of nwAtSysOperStatus indicates any problem with your AppleTalk Routing Services configuration. A value of 6 indicates that regardless of the value of nwAtSysAdminStatus, AppleTalk Routing Services is not operating because of an invalid configuration. |
| ATN nwAtSysRouterId | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1.1.1 | AtNetworkNumber | read-write | The AppleTalk node address used to uniquely identify the host (device) running the AppleTalk Routing Services. The value of nwAtSysRouterId is equal to the highest AppleTalk node address assigned to any router port. |
| nwAtSystem | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1 | |||
| STR nwAtSysVersion | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.1.2.5 | DisplayString | read-only | Indicates the current revision level of the AppleTalk Routing Services firmware, in textual format. |
| nwAtTopology | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.4 | |||
| nwAtWorkGroup | 1.3.6.1.4.1.52.4.2.2.2.3.4.2.11 | |||
| nwRtrExperimental | 1.3.6.1.4.1.52.4.2.2.2.4 |
RFC description
Provides AppleTalk routing services including system configuration, forwarding, and topology for Cabletron routers.
Start monitoring Cabletron Systems router (AppleTalk, legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.