All MIBs › CISCOSB-POLICY-MIB
Organization: Cisco Small Business
Last Updated: 2006-06-26
Category: Quality of Service, Vendor: RADLAN/Cisco SB
Description: Manages Cisco Small Business policy-map and class-map configuration for QoS and traffic enforcement.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCOSB-POLICY-MIB?
CISCOSB-POLICY-MIB is a Cisco Small Business private MIB (ORGANIZATION "Cisco Small Business", rooted under the switch001 enterprise branch) that models generic traffic-policy configuration on CISCOSB switches, functionally equivalent to CLI-based QoS class-map/policy-map configuration even though its object naming (inherited from a shared switch-silicon MIB base) uses "rlPolicy" rather than Cisco's usual class-map terminology. It defines classifier tables (rlPolicyClassifierTable, indexed by classifier type/list/sub-list) that match traffic using flow-classification byte offsets (rlPolicyFlowClassificationOffsetsTable) and OMPC (offset-match-pattern-condition) rules (rlPolicyOMPCTable), alongside metering and forwarding-action objects referenced elsewhere in the module. This lets an operator see exactly how incoming traffic is being classified and what marking/policing action a policy applies, which is essential for diagnosing QoS misclassification or unexpected DSCP remarking on a switch. It depends on the broader CISCOSB QoS/statistics MIB family (e.g., companion Dell/Cisco "rlQos"-style MIBs) for interface-level policy attachment and counters. It is deployed on Cisco Small Business managed switches used in SMB network environments; administrators can download the CISCOSB-POLICY-MIB file to load it into their MIB browser for that purpose.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCOSB-POLICY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco Small Business managed switches (CISCOSB series)
Monitoring Examples
An operator polls rlPolicyClassifierTable to review the offset-based match criteria (via rlPolicyOMPCTable entries) defining a traffic class, and checks the associated action objects to confirm DSCP remarking or metering is applied as expected; a classifier row with an unexpected rlPolicyOMPCPattern or missing rlPolicyOMPCStatus of active would explain why certain traffic isn't receiving its intended QoS treatment.
What Can Be Monitored
- traffic classifier table entries
- offset-based match pattern conditions (OMPC)
- flow classification offset groups
- classifier row/entry status
- policy action assignment
This MIB depends on
Related MIBs
Imported Objects
From CISCOSB-BRIDGEMIBOBJECTS-MIB
| VlanList1 | |
| VlanList2 | |
| VlanList3 | |
| VlanList4 |
From CISCOSB-MIB
| Percents | |
| VlanPriority | |
| switch001 | MODULE-IDENTITY |
From DIFF-SERV-MIB
| diffServClassifierEntry | OBJECT-TYPE |
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero |
From Q-BRIDGE-MIB
| PortList | |
| VlanId |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 | |
| zeroDotZero |
From SNMPv2-TC
| DisplayString | |
| RowPointer | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using rlPolicyRulesDroppedPackets OID:
Select a Cisco Small Business managed switch (CISCOSB series) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type rlPolicyRulesDroppedPackets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of packets blocked by this filtering rule. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| rlDiffservBoundaryEntry | 1.3.6.1.4.1.9.6.1.101.59.7.3.1 | not-accessible | Each boundary/interior ports table entry consists of the following parameters | |
| INT rlDiffservBoundaryIfIndex | 1.3.6.1.4.1.9.6.1.101.59.7.3.1.1 | INTEGER | read-only | The Interface index whose type is being defined |
| INT rlDiffservBoundaryPortType | 1.3.6.1.4.1.9.6.1.101.59.7.3.1.2 | INTEGER | read-write | The boundary status of the port. |
| ROW rlDiffservBoundaryStatus | 1.3.6.1.4.1.9.6.1.101.59.7.3.1.3 | RowStatus | read-write | Status of this entry. |
| rlDiffservBoundaryTable | 1.3.6.1.4.1.9.6.1.101.59.7.3 | not-accessible | Indicates whether a port is considered a boundary or an interior node of the Diffserv domain | |
| INT rlDiffservModeEnabled | 1.3.6.1.4.1.9.6.1.101.59.7.2 | INTEGER | read-write | Indicates whether Diffserv mode is currently enabled. |
| INT rlDiffservModeSupported | 1.3.6.1.4.1.9.6.1.101.59.7.1.1 | INTEGER | read-only | Indicates whether Diffserv mode is supported on the platform. |
| rlPolicy | 1.3.6.1.4.1.9.6.1.101.59 | The private MIB module definition generic traffic policy in CISCOSB devices. | ||
| rlPolicyAction | 1.3.6.1.4.1.9.6.1.101.59.5 | |||
| U32 rlPolicyActionAddTunnel | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.24 | Unsigned32 | read-write | If not zero - Tunnel is added to matched packets. |
| T/F rlPolicyActionAdvancedTrustMode | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.16 | TruthValue | read-write | Indicates if egress queue is assigned for packets match rule according to global trust mode or note. |
| T/F rlPolicyActionChangeDscp | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.3 | TruthValue | read-write | If true, the packet is re-marked with the value indicated by newDscp above. If false, the packet's DSCP value is not changed |
| T/F rlPolicyActionChangeDscpNonConform | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.14 | TruthValue | read-write | If true, the packet is re-marked with the value indicated by newDscp for non conforming packets. If false, the packet's DSCP value is not changed |
| T/F rlPolicyActionChangeIpPrecedence | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.18 | TruthValue | read-write | If true, the packet is re-marked with the value indicated by newIpPrecedence above. If false, the packet's DSCP value is not changed |
| INT rlPolicyActionChangeNewDscpNonConform | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.15 | INTEGER | read-write | Indicates the new DSCP with which the packet should be marked |
| RLP rlPolicyActionChangeVidAction | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.21 | RlPolicyMarkVlanAction | read-write | If 'mark', than the classified traffic will be remarked with new VLAN id. If 'disabled' VLAN id is not changed. If markNestedVlan, if the egress interface defined as VLAN tagged member then a new VLAN tag is added to the packet. |
| T/F rlPolicyActionChangeVpt | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.10 | TruthValue | read-write | Routed packets that run through the Rules receive VPT as define at the service class they attached to, bridge packets receive through the 802.1p operation unless we define to change the VPT for those packets. |
| T/F rlPolicyActionDroppedDropPrecedenceSupported | 1.3.6.1.4.1.9.6.1.101.59.5.1.3 | TruthValue | read-only | Indicates whether the platform support at drop precedence. |
| T/F rlPolicyActionDroppedPacketCountSupported | 1.3.6.1.4.1.9.6.1.101.59.5.1.2 | TruthValue | read-only | Indicates whether the platform can maintain a count of packets Marked for drop by a particular action. |
| C32 rlPolicyActionDroppedPackets | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.7 | Counter32 | read-only | The number of packets dropped by this action |
| INT rlPolicyActionDropPolicy | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.6 | INTEGER | read-write | |
| T/F rlPolicyActionDscpSupport | 1.3.6.1.4.1.9.6.1.101.59.5.1.6 | TruthValue | read-only | Indicates whether the platform support at DSCP filed modification. |
| INT rlPolicyActionDsQueueManagmentSupported | 1.3.6.1.4.1.9.6.1.101.59.5.1.7 | INTEGER | read-only | Indicates whether the platform supports at Q managment for implementation, mred, randomDrop used by the min/max threshold |
| rlPolicyActionEntry | 1.3.6.1.4.1.9.6.1.101.59.5.2.1 | not-accessible | Each multifield classification statement consists of the following parameters | |
| INT rlPolicyActionIndex | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.1 | INTEGER | read-only | This enumerates the Action entry. |
| OCT rlPolicyActionInProfileDropPrecedence | 1.3.6.1.4.1.9.6.1.101.59.5.1.4 | OCTET STRING | read-only | A bit mask indicating which drop precedence supported ---------- |87654321| ---------- 1 - low, 2 - medium, 3 - high, 4 - drop |
| INT rlPolicyActionMaxThreshold | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.5 | INTEGER | read-write | The max-threshold is the maximum permissible queue depth. In tail drop scenarios, the queue will drop if a packet is presented to it and it is instantaneously full by this measure. In random drop scenarios, the queue will drop if a packet is presented to it and the average queue depth exceeds the max-threshold. This object is in the action table rather than the queue table because Differentiated Services PHBs, such as the Assured Service, permit differently classified traffic to have different drop parameters even though they occupy the same queue. |
| INT rlPolicyActionMinThreshold | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.4 | INTEGER | read-write | The min-threshold is the queue depth that a random drop process will seek to manage the queue's depth to. This object is in the action table rather than the queue table because Differentiated Services PHBs, such as the Assured Service, permit differently classified traffic to have different drop parameters even though they occupy the same queue. |
| INT rlPolicyActionMREDSupported | 1.3.6.1.4.1.9.6.1.101.59.5.1.1 | INTEGER | read-only | Indicates whether the platform supports setting MRED characteristics in the packet action |
| INT rlPolicyActionNewDscp | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.2 | INTEGER | read-write | Indicates the new DSCP with which the packet should be marked |
| NUM rlPolicyActionNewInterface | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.20 | InterfaceIndexOrZero | read-write | Relevant if rlQosClassMapRedirect is either 'redirectToInterface' or 'analyzerPort'. Specified the output interface the packet is redireted to or the port that gets copy of the packet in addition to the port it was farwarded. |
| INT rlPolicyActionNewIpPrecedence | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.17 | INTEGER | read-write | Indicates the new Ip- Precedence with which the packet should be marked |
| INT rlPolicyActionNewVid | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.22 | INTEGER | read-write | If rlPolicyActionChangeVid is true, specify the new Vlan id to assigned to the packet |
| INT rlPolicyActionNewVpt | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.11 | INTEGER | read-write | Priority Tag that will be written to packets . |
| INT rlPolicyActionNonDsInProfileDropPrecedence | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.8 | INTEGER | read-write | This paramer is used at non diffserv mode to attached the drop precedence for packet InProfile (metering), only if there is a support for drop precedence and with what level. |
| INT rlPolicyActionNonDsOutProfileDropPrecedence | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.9 | INTEGER | read-write | This paramer is used at non diffserv mode to attached the drop precedence for packet OutProfile (metering), only if there is a support for drop precedence and with what level. |
| OCT rlPolicyActionOutProfileDropPrecedence | 1.3.6.1.4.1.9.6.1.101.59.5.1.5 | OCTET STRING | read-only | A bit mask indicating which drop precedence supported ---------- |87654321| ---------- 1 - low, 2 - medium, 3 - high, 4 - drop |
| rlPolicyActionPlatDependParams | 1.3.6.1.4.1.9.6.1.101.59.5.1 | |||
| RLP rlPolicyActionReDirect | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.19 | RlPolicyRedirectAction | read-write | Specified the redirection action/ |
| INT rlPolicyActionServiceClassPointer | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.12 | INTEGER | read-write | Specifies the index in rlPolicyServiceClassTable denoting the service class to which the packet should be assigned after the action specified in this entry is carried out. A value of 0 means that no Service class is assigned. A value of 0 is legal only for routedIp packets in Diffserv mode on Inbound processing. |
| ROW rlPolicyActionStatus | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.13 | RowStatus | read-write | The status of the table entry |
| rlPolicyActionTable | 1.3.6.1.4.1.9.6.1.101.59.5.2 | not-accessible | This table defines the Actions for packets that pass the meter table ie. the characteristics that are assigned to packets before they reach the scheduler. When Diffserv is not in effect(ie. IPX, bridging, or IP when the global option for Diffserv is off), certain table parameters are not available(see below). The DiffServ option is enabled or disabled by setting rlDiffservModeEnabled. | |
| INT rlPolicyActionTrapTypeId | 1.3.6.1.4.1.9.6.1.101.59.5.2.1.23 | INTEGER | read-write | If now zero, Indicates the trap type id the matched packets arrives with, relevant when RedirectAction is trap or mirror. |
| INT rlPolicyActiveServiceClassTable | 1.3.6.1.4.1.9.6.1.101.59.6.3 | INTEGER | read-write | Specifies the Service Class table preform active action (usuarlly after set of entries at the service class tentative table). Specifies the current status of a table, there could be two options, tentative/active table. only the tentative table is the read-write and the active table is read-only. at set to activeAction the tentative table will be copied to the active table. |
| RLP rlPolicyAdvcGlobalTrustMode | 1.3.6.1.4.1.9.6.1.101.59.16.1.4 | RlPolicyTrustTypes | read-write | This field replaces deprecated scalar rlPolicyCliBasicModeCfg. Defines the global qos trust operation mode when qos mode is advanced. |
| RLP rlPolicyBasicGlobalTrustMode | 1.3.6.1.4.1.9.6.1.101.59.16.1.3 | RlPolicyTrustTypes | read-write | This field replaces deprecated scalar rlPolicyCliBasicModeCfg. Defines the global qos trust operation mode when qos mode is basic. |
| INT rlPolicyBoundedPriorityQueueSupport | 1.3.6.1.4.1.9.6.1.101.59.6.1.2 | INTEGER | read-only | Indicates whether the platform supports setting an upper limit to the bandwidth of traffic transmitted on queues operating in Strict Priority mode. |
| rlPolicyClassifier | 1.3.6.1.4.1.9.6.1.101.59.2 | |||
| OCT rlPolicyClassifierAdditionalCriteriaSupported | 1.3.6.1.4.1.9.6.1.101.59.2.1.8 | OCTET STRING | read-only | A bit mask indicating which additional Criteria may be supported by the classifier: ---------- |87654321| ---------- 1 - input port supported 2 - output port supported 3 - VLAN ID for bridging supported 4 - VPT ID for bridging supported 5 - EtherType ID for bridging supported 6 - Inner VLAN ID for bridging supported |
| T/F rlPolicyClassifierAdditionalCriteriaUsedInOffsetCount | 1.3.6.1.4.1.9.6.1.101.59.2.1.9 | TruthValue | read-only | Indicates whether the additional FCOG or Classifier criteria (ie. inPort, outPort VID count towards the maximum number of offsets ie. whether using inPort in the FCOG reduces the maximum number of offsets available. |
| RLP rlPolicyClassifierDiffservInIfType | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.9 | RlPolicyClassifierDiffservIfType | read-write | For a classifier used by the Diffserv Rules table. Enables specification of a classifier that should apply to all Diffserv boundary ports or all Diffserv Interior ports. If normal is specified, the rlPolicyClassifierInIfIndex field is used as it is in the non-diffserv case. If allBoundary or allInterior is selected, rlPolicyClassifierInIfIndex is ignored |
| RLP rlPolicyClassifierDiffservOutIfType | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.10 | RlPolicyClassifierDiffservIfType | read-write | For a classifier used by the Diffserv Rules table. Enables specification of a classifier that should apply to outbound traffic on all Diffserv boundary ports or all Diffserv Interior ports. If normal is specified, the rlPolicyClassifierOutIfIndex field is used as it is in the non-diffserv case. If allBoundary or allInterior is selected, rlPolicyClassifierOutIfIndex is ignored |
| rlPolicyClassifierEntry | 1.3.6.1.4.1.9.6.1.101.59.2.4.1 | not-accessible | Classifiers can be of the ingress, egress, or post-routing phase varieties. Each multifield classification statement consists of the following parameters. | |
| INT rlPolicyClassifierEtherTypeID | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.16 | INTEGER | read-write | EtherType ID, to be compared with. 65535 is used to indicate not used value for this classifier 1499 is uded to indicate IPv4 ethertype that is originated from IPv4 ACL with permit/deny any any any 1500 is uded to indicate IPv6 ethertype that is originated from IPv6 ACL with permit/deny any any any |
| INT rlPolicyClassifierIndex | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.4 | INTEGER | read-only | Index into the Classifier Table. |
| NUM rlPolicyClassifierInIfIndex | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.6 | InterfaceIndexOrZero | read-write | Input interface index to be compared with received packet, a value of 0 denotes that the classifier is applied to all ports. |
| POR rlPolicyClassifierInIfIndexList | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.12 | PortList | read-write | allow to define list of ports for the specific classifier for ingress classification. if rlPolicyClassifierInIfIndex equal to zero then the following list should be reffered , if the list is empty we refer to ALL Ports |
| INT rlPolicyClassifierInnerVID | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.17 | INTEGER | read-write | INNER VLAN ID, used only for double tagged traffic. |
| INT rlPolicyClassifierListIndex | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.2 | INTEGER | read-only | List Index into the Classifier Table. |
| OCT rlPolicyClassifierOMPCActions | 1.3.6.1.4.1.9.6.1.101.59.2.1.11 | OCTET STRING | read-only | A bit mask indicating which operation could be performed with OPMC ---------- |87654321| ---------- 1 - equal, 2 - notEqual, 3 - bigger, 4 - smaller. |
| OID rlPolicyClassifierOmpcList | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.5 | OBJECT IDENTIFIER | read-write | The list of OMPCs to check with this Classifier. Each subidentifier together with rlPolicyClassifierType specify one OMPC. |
| NUM rlPolicyClassifierOutIfIndex | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.7 | InterfaceIndexOrZero | read-write | Output interface index to be compared with sent packet, a value of 0 denotes that the classifier is applied to all ports. |
| POR rlPolicyClassifierOutIfIndexList | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.13 | PortList | read-write | allow to define list of ports for the specific classifier for egress classification. if rlPolicyClassifierOutIfIndex equal to zero then the following list should be reffered , if the list is empty we refer to ALL Ports |
| OCT rlPolicyClassifierPermittedOffsetTypes | 1.3.6.1.4.1.9.6.1.101.59.2.1.10 | OCTET STRING | read-only | A bit mask indicating which offset types are supported by the platform for FCOG and OMPC definitions: ---------- |87654321| ---------- 1 - L2 offsets supported 2 - L3 offsets supported |
| rlPolicyClassifierPlatDependParams | 1.3.6.1.4.1.9.6.1.101.59.2.1 | |||
| ROW rlPolicyClassifierStatus | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.11 | RowStatus | read-write | The status of a table entry. It is used to delete an entry from this table. |
| INT rlPolicyClassifierSubListIndex | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.3 | INTEGER | read-only | SubList Index into the Classifier Table. |
| rlPolicyClassifierTable | 1.3.6.1.4.1.9.6.1.101.59.2.4 | not-accessible | The table of Classifier statement. | |
| RLP rlPolicyClassifierType | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.1 | RlPolicyGroupType | read-only | Specifies a classifier type for which offset bytes can be specified. |
| rlPolicyClassifierUtilization | 1.3.6.1.4.1.9.6.1.101.59.13 | |||
| rlPolicyClassifierUtilizationEntry | 1.3.6.1.4.1.9.6.1.101.59.13.1.1 | not-accessible | A Single entry containing Classifier utilization information. | |
| U32 rlPolicyClassifierUtilizationPercent | 1.3.6.1.4.1.9.6.1.101.59.13.1.1.2 | Unsigned32 | read-only | The classifier utilization percentage. |
| U32 rlPolicyClassifierUtilizationRulesNumber | 1.3.6.1.4.1.9.6.1.101.59.13.1.1.3 | Unsigned32 | read-only | The classifier utilization number of used rules, in short rules resolution. |
| rlPolicyClassifierUtilizationTable | 1.3.6.1.4.1.9.6.1.101.59.13.1 | not-accessible | A table containing Classifier utilization information. Each row represents objects for a particular Unit present in this system. | |
| U32 rlPolicyClassifierUtilizationUnitId | 1.3.6.1.4.1.9.6.1.101.59.13.1.1.1 | Unsigned32 | not-accessible | The Unit ID of this Classifier. must be unique per entry. This is an index into the table. |
| INT rlPolicyClassifierVID | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.8 | INTEGER | read-write | VLAN ID, used only for bridged traffic. |
| INT rlPolicyClassifierVPTID | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.14 | INTEGER | read-write | VPT ID - user priority tag to be compared with . 8 is used to indicate not used value for this classifier |
| INT rlPolicyClassifierVPTIDMask | 1.3.6.1.4.1.9.6.1.101.59.2.4.1.15 | INTEGER | read-write | VPT ID Mask ,mask the user priority field . 0 is the default indicate Mask all compared with any VPT value |
| INT rlPolicyClearCounters | 1.3.6.1.4.1.9.6.1.101.59.12.4 | INTEGER | read-write | This scalar indicates to clear all the counters. |
| INT rlPolicyCPUSafeGuardEnable | 1.3.6.1.4.1.9.6.1.101.59.15 | INTEGER | read-write | This scalar enables/disables CPU Safeguard. |
| INT rlPolicyDefaultForwardingAction | 1.3.6.1.4.1.9.6.1.101.59.11.1.8 | INTEGER | read-write | Default Forwarding Action specify permit or deny |
| rlPolicyDefaultForwardingEntry | 1.3.6.1.4.1.9.6.1.101.59.11.1 | not-accessible | Since the table is search to find match according to first match Entries with specific protocol should be set before entries for entire layer. | |
| INT rlPolicyDefaultForwardingIndex | 1.3.6.1.4.1.9.6.1.101.59.11.1.1 | INTEGER | read-only | Default Forwarding Index. |
| INT rlPolicyDefaultForwardingLayer | 1.3.6.1.4.1.9.6.1.101.59.11.1.7 | INTEGER | read-write | Default Forwarding Action specify layer l2 l3 l3-ipv6 |
| POR rlPolicyDefaultForwardingPortList | 1.3.6.1.4.1.9.6.1.101.59.11.1.2 | PortList | read-write | Default Forwarding Port List. |
| INT rlPolicyDefaultForwardingProtocol | 1.3.6.1.4.1.9.6.1.101.59.11.1.10 | INTEGER | read-write | The protocol type to be applied with the default action. |
| ROW rlPolicyDefaultForwardingStatus | 1.3.6.1.4.1.9.6.1.101.59.11.1.9 | RowStatus | read-write | The status of a table entry. It is used to delete/Add an entry from this table. |
| rlPolicyDefaultForwardingTable | 1.3.6.1.4.1.9.6.1.101.59.11 | not-accessible | This table specifies The default forwarding values : permit or deny for list of specific ports , vlans | |
| VLA rlPolicyDefaultForwardingVlanId1025To2048 | 1.3.6.1.4.1.9.6.1.101.59.11.1.4 | VlanList2 | read-write | Default Forwarding VlanId List 2. |
| VLA rlPolicyDefaultForwardingVlanId1To1024 | 1.3.6.1.4.1.9.6.1.101.59.11.1.3 | VlanList1 | read-write | Default Forwarding VlanId List 1. |
| VLA rlPolicyDefaultForwardingVlanId2049To3072 | 1.3.6.1.4.1.9.6.1.101.59.11.1.5 | VlanList3 | read-write | Default Forwarding VlanId List 3. |
| VLA rlPolicyDefaultForwardingVlanId3073To4096 | 1.3.6.1.4.1.9.6.1.101.59.11.1.6 | VlanList4 | read-write | Default Forwarding VlanId List 4. |
| INT rlPolicyDefaultServiceClass | 1.3.6.1.4.1.9.6.1.101.59.6.2 | INTEGER | read-write | Indicates which service class is default one for packets whose COS is undetermined. |
| rlPolicyDiffServ | 1.3.6.1.4.1.9.6.1.101.59.7 | |||
| rlPolicyDiffServPlatDependParams | 1.3.6.1.4.1.9.6.1.101.59.7.1 | |||
| INT rlPolicyDp | 1.3.6.1.4.1.9.6.1.101.59.10.7.1.2 | INTEGER | read-write | New DP. |
| T/F rlPolicyDroppedPacketCountSupported | 1.3.6.1.4.1.9.6.1.101.59.3.1.1 | TruthValue | read-only | Indicates whether the dropped packets counter in the rlPolicyRulesTable is supported. |
| rlPolicyDropProfileEntry | 1.3.6.1.4.1.9.6.1.101.59.6.7.1 | not-accessible | Configuration parameters for each port/service class. | |
| INT rlPolicyDropProfileIndex | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.1 | INTEGER | read-only | Interface index. |
| INT rlpolicyDropProfilePointer | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.5 | INTEGER | read-write | pointing to drop algorithem profile. the profile describs the drop algorithem (tail, red)and params |
| INT rlPolicyDropProfileQueueNumber | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.2 | INTEGER | read-only | Interface Queue number. |
| INT rlPolicyDropProfileRedMaxDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.7 | INTEGER | read-write | WRED Max Threshold for Drop Precedence 0. UNITS percent 0-100 0-100 |
| INT rlPolicyDropProfileRedMaxDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.10 | INTEGER | read-write | WRED Max Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyDropProfileRedMaxDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.13 | INTEGER | read-write | WRED Max Threshold for Drop Precedence 2. UNITS percent 0-100 |
| INT rlPolicyDropProfileRedMinDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.6 | INTEGER | read-write | WRED Min Threshold for Drop Precedence 0. UNITS percent 0-100 |
| INT rlPolicyDropProfileRedMinDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.9 | INTEGER | read-write | WRED Min Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyDropProfileRedMinDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.12 | INTEGER | read-write | WRED Min Threshold for Drop Precedence 2. UNITS percent 0-100 |
| INT rlPolicyDropProfileRedProbDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.8 | INTEGER | read-write | WRED probability for Drop Precedence 0. |
| INT rlPolicyDropProfileRedProbDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.11 | INTEGER | read-write | WRED probability for Drop Precedence 1. |
| INT rlPolicyDropProfileRedProbDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.14 | INTEGER | read-write | WRED probability for Drop Precedence 2. |
| INT rlPolicyDropProfileRedQweight | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.15 | INTEGER | read-write | additional parameter for the WRED algorithem supporting the Queue weight exponentail factor |
| ROW rlPolicyDropProfileStatus | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.16 | RowStatus | read-write | Status of this entry. |
| rlPolicyDropProfileTable | 1.3.6.1.4.1.9.6.1.101.59.6.7 | not-accessible | this table defines drop profile which describ the queue's drop algorithems | |
| INT rlPolicyDropProfileTdThersholdDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.3 | INTEGER | read-write | Tail Drop Threshold for Drop Precedence 0. UNITS percent 0-100 |
| INT rlPolicyDropProfileTdThersholdDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.4 | INTEGER | read-write | Tail Drop Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyDropProfileTdThersholdDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.7.1.5 | INTEGER | read-write | Tail Drop Threshold for Drop Precedence 2. UNITS percent 0-100 |
| INT rlPolicyDscp | 1.3.6.1.4.1.9.6.1.101.59.10.7.1.1 | INTEGER | read-only | Packet DSCP. |
| INT rlPolicyDscpIndex | 1.3.6.1.4.1.9.6.1.101.59.10.1.1.1 | INTEGER | read-only | DSCP value. |
| T/F rlPolicyDscpMutationEnable | 1.3.6.1.4.1.9.6.1.101.59.16.1.6 | TruthValue | read-write | This field indicates if dscp to dscp mutation mode is enable. It can be set to true in the following terms: 1.rlQosGlobalTrustMode is in {dscp, vpt-dscp} ( rlQosGlobalQoSMode must be basic or advanced) 2.if rlQosGlobalQoSMode is advanced then rlQoSPortTrustAdvancedMode must be set to true. |
| rlPolicyDscpMutationEntry | 1.3.6.1.4.1.9.6.1.101.59.10.4.1 | not-accessible | Each entry in this table describes the new DSCP for the packet. The index is Old DSCP represent by rlPolicyOldDscp | |
| ROW rlPolicyDscpMutationStatus | 1.3.6.1.4.1.9.6.1.101.59.10.4.1.3 | RowStatus | read-write | The status of a table entry. It is used to delete/Add an entry from this table. |
| rlPolicyDscpMutationTable | 1.3.6.1.4.1.9.6.1.101.59.10.4 | not-accessible | This table specifies The DSCP Mutation table | |
| rlPolicyDscpRemarkEntry | 1.3.6.1.4.1.9.6.1.101.59.10.3.1 | not-accessible | Each entry in this table describes the new DSCP for the packet. The index is Old DSCP represent by rlPolicyOldDscp | |
| ROW rlPolicyDscpRemarkStatus | 1.3.6.1.4.1.9.6.1.101.59.10.3.1.3 | RowStatus | read-write | The status of a table entry. It is used to delete/Add an entry from this table. |
| rlPolicyDscpRemarkTable | 1.3.6.1.4.1.9.6.1.101.59.10.3 | not-accessible | This table specifies The DSCP Remark table | |
| rlPolicyDscpServiceClassEntry | 1.3.6.1.4.1.9.6.1.101.59.10.1.1 | not-accessible | Each entry in this table describes The ServiceClass assigned to a Dscp value. The index is DSCP represent by rlPolicyDscpIndex | |
| ROW rlPolicyDscpServiceClassStatus | 1.3.6.1.4.1.9.6.1.101.59.10.1.1.3 | RowStatus | read-write | The status of a table entry. It is used to delete/Add an entry from this table. |
| rlPolicyDscpServiceClassTable | 1.3.6.1.4.1.9.6.1.101.59.10.1 | not-accessible | This table specifies The DSCP to ServiceClass map table | |
| rlPolicyDscpToDpEntry | 1.3.6.1.4.1.9.6.1.101.59.10.7.1 | not-accessible | Each entry in this table describes the new DP for the packet. The index is DSCP represent by rlPolicyDscp | |
| ROW rlPolicyDscpToDpStatus | 1.3.6.1.4.1.9.6.1.101.59.10.7.1.3 | RowStatus | read-write | The status of a table entry. It is used to delete/Add an entry from this table. |
| rlPolicyDscpToDpTable | 1.3.6.1.4.1.9.6.1.101.59.10.7 | not-accessible | This table specifies The DSCP To Dp table | |
| INT rlPolicyDscpValue | 1.3.6.1.4.1.9.6.1.101.59.10.6.1.1 | INTEGER | read-only | DSCP value. |
| rlPolicyDscpVptEntry | 1.3.6.1.4.1.9.6.1.101.59.10.6.1 | not-accessible | Each entry in this table describes The VPT assigned to a Dscp value. The index is DSCP represent by rlPolicyDscpValue. | |
| ROW rlPolicyDscpVptStatus | 1.3.6.1.4.1.9.6.1.101.59.10.6.1.3 | RowStatus | read-write | The status of a table entry. It is used to delete/Add an entry from this table. |
| rlPolicyDscpVptTable | 1.3.6.1.4.1.9.6.1.101.59.10.6 | not-accessible | This table specifies The DSCP to VPT map table | |
| T/F rlPolicyEgressMeteringSupported | 1.3.6.1.4.1.9.6.1.101.59.3.1.4 | TruthValue | read-only | Specifies whether the platform supports metering on outbound packet rules (for Diffserv). |
| OCT rlPolicyFilterActionOptions | 1.3.6.1.4.1.9.6.1.101.59.3.1.2 | OCTET STRING | read-only | A bit mask indicating which operation could be perform ---------- |87654321| ---------- 1 - block, 2 - blockAndTrap, 3 - permitAndTrap, 4 - permit. |
| INT rlPolicyFlowClassificationOffsetGroupMaximumOffset | 1.3.6.1.4.1.9.6.1.101.59.2.1.3 | INTEGER | read-only | Indicates the maximum value of a byte offset in a Flow Classification Offset Group. If 0, there is no limit. |
| rlPolicyFlowClassificationOffsetsGroupEntry | 1.3.6.1.4.1.9.6.1.101.59.2.2.1 | not-accessible | The flow classification offset table entry includes the following parameters | |
| OCT rlPolicyFlowClassificationOffsetsGroupMask | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.4 | OCTET STRING | read-write | The list of masks corresponding to the offsets to be included in the Flow Classification Offset Group are specified as bytes in the OID(after the first 2 bytes which must be 1.1). |
| OID rlPolicyFlowClassificationOffsetsGroupOffset | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.2 | OBJECT IDENTIFIER | read-write | The list of offsets to be included in the Flow Classification Offset Group are specified as subidentifiers in the OID(after the first 2 bytes which must be 1.1). The maximal number of permissible offsets is given by rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup. The maximal value that an offset can have is rlPolicyFlowClassificationOffsetGroupMaximumOffset. |
| OID rlPolicyFlowClassificationOffsetsGroupOffsetType | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.3 | OBJECT IDENTIFIER | read-write | Indicates whether the corresponding byte denotes an offset from beginning of L2, from the beginning of L3 IPv4 packet data or from the beginning of L3 IPv6 packet data. Each byte in the OID contains either: (1) - L2 offset (2) - L3 Offset (3) - L3 IPv6 Offset |
| INT rlPolicyFlowClassificationOffsetsGroupScheme | 1.3.6.1.4.1.9.6.1.101.59.2.1.1 | INTEGER | read-only | Some platforms allow Policy statements to examine all packet offsets(Opal); other platforms require specification of specific byte offsets for routedIp packets, another set of offsets for routedIpx, a third set for bridge. |
| ROW rlPolicyFlowClassificationOffsetsGroupStatus | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.8 | RowStatus | read-write | The status of a table entry. It is used to delete an entry from this table. |
| RLP rlPolicyFlowClassificationOffsetsGroupType | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.1 | RlPolicyGroupType | read-only | Specifies a classifier type for which offset bytes can be specified. |
| T/F rlPolicyFlowClassificationOffsetsGroupUseEtherTypeId | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.10 | TruthValue | read-write | Indicates whether or not the EtherType is usable in Policy Rule definitions for bridged packets |
| T/F rlPolicyFlowClassificationOffsetsGroupUseInnerVlanId | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.11 | TruthValue | read-write | Indicates whether or not the inner VlanId is usable in Policy Rule definitions for bridged packets |
| T/F rlPolicyFlowClassificationOffsetsGroupUseInputInterface | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.5 | TruthValue | read-write | Indicates whether or not the Input Interface Index is usable in Policy Rule definitions. |
| T/F rlPolicyFlowClassificationOffsetsGroupUseOutputInterface | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.6 | TruthValue | read-write | Indicates whether or not the Output Interface Index(ie. routing/bridging decision) is usable in Policy Rule definitions |
| T/F rlPolicyFlowClassificationOffsetsGroupUseVlanId | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.7 | TruthValue | read-write | Indicates whether or not the VlanId is usable in Policy Rule definitions for bridged packets |
| T/F rlPolicyFlowClassificationOffsetsGroupUseVPTId | 1.3.6.1.4.1.9.6.1.101.59.2.2.1.9 | TruthValue | read-write | Indicates whether or not the VPT is usable in Policy Rule definitions for bridged packets |
| rlPolicyFlowClassificationOffsetsTable | 1.3.6.1.4.1.9.6.1.101.59.2.2 | not-accessible | Specifies the byte offsets that the platform can use for policy decisions. This table is used for platforms which impose limitations on choosing the OMPCs for classification. If the platform does not impose any limitations, the value of rlPolicyFlowClassificationOffsetsGroupScheme is allOffsetsPermitted. Each entry in the table specifies a combination of byte offsets which can be used to specify flow classification. A rule may use a subset of the bytes of its Offset Group. The maximum value for each offset is given by rlPolicyFlowClassificationOffsetGroupMaximumOffset. The maximum number of offsets per Offset Group is given by rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup. | |
| INT rlPolicyGlobalAdminTrapfrequency | 1.3.6.1.4.1.9.6.1.101.59.9.3 | INTEGER | read-write | define the the min number of seconds between successive traps. 0 means no traps will be sent, uints in Sec |
| T/F rlPolicyGlobalClassifyIpPrecedenceSupported | 1.3.6.1.4.1.9.6.1.101.59.9.9 | TruthValue | read-only | Indicates if the system support classification according ip precedence most significant 3 bits in the TOS byte |
| T/F rlPolicyGlobalDefaultForwarding | 1.3.6.1.4.1.9.6.1.101.59.9.2 | TruthValue | read-write | Indicates whether or not the unmach traffic is forwarded or blocked. |
| INT rlPolicyGlobalDeviceQosOperationTypes | 1.3.6.1.4.1.9.6.1.101.59.9.7 | INTEGER | read-only | Indicates if the system support basic or advanced mode or Both basic and Advanced |
| INT rlPolicyGlobalDeviceShapingTypeSupported | 1.3.6.1.4.1.9.6.1.101.59.9.10 | INTEGER | read-only | Indicates the shaper shaper type supported for the device |
| T/F rlPolicyGlobalDscpMutationSupported | 1.3.6.1.4.1.9.6.1.101.59.9.8 | TruthValue | read-only | mutation over the ingress packet dscp field supported for the device. |
| T/F rlPolicyGlobalDscpRemarkingSupported | 1.3.6.1.4.1.9.6.1.101.59.9.11 | TruthValue | read-only | Indicates if dscp remarking supported for the device |
| INT rlPolicyGlobalIndex | 1.3.6.1.4.1.9.6.1.101.59.16.1.1 | INTEGER | not-accessible | Entry index - currenly only one entry can exist, indexes hard coded with value '1'. |
| INT rlPolicyGlobalOperationEnabled | 1.3.6.1.4.1.9.6.1.101.59.9.1 | INTEGER | read-write | Indicates whether Policy is currently enabled. |
| INT rlPolicyGlobalOperTrapElapsedTime | 1.3.6.1.4.1.9.6.1.101.59.9.4 | INTEGER | read-only | show the time out elaps from the last trap sent uints in Sec. |
| rlPolicyGlobalParams | 1.3.6.1.4.1.9.6.1.101.59.9 | |||
| RLP rlPolicyGlobalQoSMode | 1.3.6.1.4.1.9.6.1.101.59.9.5 | RlPolicyQosMode | read-write | V750 DEPRECATED - replaced with rlPolicyGlobalQosMode field in rlPolicyQosModeGlobalCfg table. user can set the system to operate either in the Basic mode or in the Advanced mode |
| INT rlPolicyGlobalqueueSchedulerPerDeviceOrPort | 1.3.6.1.4.1.9.6.1.101.59.9.12 | INTEGER | read-only | indicates if the system support scheduling configuration per port or per device. device (1 ) or port (2) |
| C64 rlPolicyGlobalStatisticsCntrsCounterValue | 1.3.6.1.4.1.9.6.1.101.59.12.3.1.3 | Counter64 | read-only | Counter value. |
| rlPolicyGlobalStatisticsCntrsEntry | 1.3.6.1.4.1.9.6.1.101.59.12.3.1 | not-accessible | Each entry represents global counter. | |
| STA rlPolicyGlobalStatisticsCntrsNumOfBits | 1.3.6.1.4.1.9.6.1.101.59.12.3.1.2 | StatisticsCntrNumOfBitsType | read-only | Counter size in bits. |
| rlPolicyGlobalStatisticsCntrsTable | 1.3.6.1.4.1.9.6.1.101.59.12.3 | not-accessible | This table specifies statistics global counters for specific rules for all ports that they are connected to | |
| STA rlPolicyGlobalStatisticsCntrsType | 1.3.6.1.4.1.9.6.1.101.59.12.3.1.1 | StatisticsCntrType | read-only | Counter type. |
| ROW rlPolicyGlobalStatisticsStatus | 1.3.6.1.4.1.9.6.1.101.59.12.3.1.4 | RowStatus | read-write | The status of a table entry. It is used to delete an entry from this table. |
| RLP rlPolicyGlobalTrustMode | 1.3.6.1.4.1.9.6.1.101.59.9.6 | RlPolicyTrustTypes | read-write | V750 DEPRECATED - replaced with rlPolicyGlobalTrustMode field in rlPolicyQosModeGlobalCfg table. Global Trust state. the value refered to Basic mode and specify the trust mode the device is support. all phisical ports are trusted |
| T/F rlPolicyIngressMeteringSupported | 1.3.6.1.4.1.9.6.1.101.59.3.1.3 | TruthValue | read-only | Specifies whether the platform supports metering in inbound packet rules. |
| U32 rlPolicyIsTCAvailable | 1.3.6.1.4.1.9.6.1.101.59.14 | Unsigned32 | read-only | This scalar indicates the number of currently reserved amount of traffic conditioners. |
| INT rlPolicyMappedServiceClass | 1.3.6.1.4.1.9.6.1.101.59.10.2.1.3 | INTEGER | read-write | ServiceClass value. |
| rlPolicyMapping | 1.3.6.1.4.1.9.6.1.101.59.10 | |||
| INT rlPolicyMaxOMPCLengthForBiggerSmallerOperation | 1.3.6.1.4.1.9.6.1.101.59.2.1.7 | INTEGER | read-only | Indicates the maximal permissible length of an OMPC using bigger' or 'smaller' condition. If 0, there is no limit. |
| rlPolicyMeterClass | 1.3.6.1.4.1.9.6.1.101.59.4 | |||
| rlPolicyMeterClassTable | 1.3.6.1.4.1.9.6.1.101.59.4.2 | not-accessible | This table defines the Metering classes for the system. | |
| INT rlPolicyMeterDepth | 1.3.6.1.4.1.9.6.1.101.59.4.1.1 | INTEGER | read-only | Indicates how many meters can be chained in succession (ie. so that if the first meter fails, the second can be examined). The final meter in a sequence is always 'always-conform', so if the value of this parameter is 2, the platform that supports a single meter and then a second marking/action for meter failure. |
| INT rlPolicyMeteringClassActionPointer | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.7 | INTEGER | read-write | Specifies the index in the rlPolicyActionTable to be accessed for packets that are in-profile. Value 0 is interpreted to mean no action. A non-zero value may be specified only for RoutedIp packets in Diffserv mode. |
| INT rlPolicyMeteringClassAggregateMeterBurstSize | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.4 | INTEGER | read-write | The Burst Size parameter for the aggregate meter leaky bucket. A value of 0 means that the device should choose the Burst Size that it thinks is most suitable for the rule. The interval can be derived from (burstSizex8/Rate). |
| INT rlPolicyMeteringClassAggregateMeterRate | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.3 | INTEGER | read-write | The rate in kilobytes/second of traffic considered within the bandwidth allocated for this policy entry. |
| T/F rlPolicyMeteringClassAlwaysConform | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.2 | TruthValue | read-write | If true, the meter always accepts all traffic; its rate is effectively infinite. In such a case, the token bucket defined by the MeterRate and Burst-Size parameters is ignored. also used when there isn't metering support. |
| rlPolicyMeteringClassEntry | 1.3.6.1.4.1.9.6.1.101.59.4.2.1 | not-accessible | Each statement consists of the following parameters | |
| INT rlPolicyMeteringClassFailMeterPointer | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.8 | INTEGER | read-write | Specifies an index in the rlPolicyMeterClassTable. This is the meter that is to be used if the packet is out-of-profile relative to the current meter. If non-Diffserv mode, this field is not used. If the current meter is AlwaysConform, this field is not used. |
| INT rlPolicyMeteringClassIndex | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.1 | INTEGER | read-only | This enumerates the table entry. |
| C32 rlPolicyMeteringClassInProfileCounter | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.11 | Counter32 | read-only | meter counter for packets that are in profile . |
| INT rlPolicyMeteringClassMaxSessionLimit | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.6 | INTEGER | read-write | indicate a the maximum number of session for a sepecific rule to guarante minimum bandwidth. Value 0 at rlPolicyMeteringClassPerSessionMetering and rlPolicyMeteringClassMaxSessionLimit is interpreted to mean no sepecific requarment and the aggregate metering will be done by the system decision. |
| C32 rlPolicyMeteringClassOutProfileCounter | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.12 | Counter32 | read-only | meter counter for packets that are out of profile |
| INT rlPolicyMeteringClassPerSessionMeteringRate | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.5 | INTEGER | read-write | A Quantitative Appliction policy rule where each individual session requires a guaranteed minimum bandwidth. Specifies the Ingress traffic flow meter per session indicate a bandwidth limit to be applied to each individual session Value 0 at rlPolicyMeteringClassPerSessionMetering and rlPolicyMeteringClassMaxSessionLimit is interpreted to mean no sepecific requarment and the aggregate metering will be done by the system decision. The rate in kilobytes/second |
| ROW rlPolicyMeteringClassStatus | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.9 | RowStatus | read-write | The status of a table entry. It is used to delete an entry from this table. |
| T/F rlPolicyMeteringCounterEnable | 1.3.6.1.4.1.9.6.1.101.59.4.2.1.10 | TruthValue | read-write | Enable metering counter for the meter entry. |
| rlPolicyMeterPlatDependParams | 1.3.6.1.4.1.9.6.1.101.59.4.1 | |||
| INT rlPolicyMibVersion | 1.3.6.1.4.1.9.6.1.101.59.1 | INTEGER | read-only | MIB's version, the current version is 14 1 - original version 2 - two new fields rlPolicyActionChangeDscpNonConform rlPolicyActionNewDscpNonConform were added. 3 - added support new policy features QoS modes: basic and advanced support for trusted mode operations mapping tables for trusted ports dscp, tcpUdp, mutation, remarking. 4 - I) added support to service mode. II)DSCP to VPT mapping table III) download marker 5 - Added cos-Dscp to RlPolicyTrustTypes 6 - Added rlPolicyFlowClassificationOffsetsGroupUseVPTId and rlPolicyFlowClassificationOffsetsGroupUseEtherTypeId To rlPolicyFlowClassificationOffsetsTable Added rlPolicyClassifierVPTID And rlPolicyClassifierEtherTypeID To rlPolicyClassifierTable Added Vpt and Ethertype support to rlPolicyClassifierAdditionalCriteriaSupported 7 - Added rlPolicyPortCfgPortRateLimitStatus,rlPolicyPortCfgCirPortRateLimit rlPolicyPortCfgCbsPortRateLimit to rlPolicyPortConfigurationTable 8 - Added rlPolicyDefaultForwardingProtocol to rlPolicyDefaultForwardingTable Added rlPolicyDscpToDpTable 9 - Add statistics 10 - Add classifier utilization 11 -Added rlPolicyFlowClassificationOffsetsGroupUseInnerVlanId To rlPolicyFlowClassificationOffsetsTable Added rlPolicyClassifierInnerVID To rlPolicyClassifierTable Added Inner vlan id support to rlPolicyClassifierAdditionalCriteriaSupported 12 - Added rlPolicyVlanConfigurationTable 13 - Added rlPolicyIsTCAvailable scalar 14 - Added rlPolicyCPUSafeGuardEnable |
| ROW rlPolicyModeGlobalCfgStatus | 1.3.6.1.4.1.9.6.1.101.59.16.1.7 | RowStatus | read-write | This status of entry action. In current implementation only one entry exist, therefor only status = active is acceptable. |
| INT rlPolicyNewDscp | 1.3.6.1.4.1.9.6.1.101.59.10.4.1.2 | INTEGER | read-write | New DSCP. |
| INT rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup | 1.3.6.1.4.1.9.6.1.101.59.2.1.2 | INTEGER | read-only | For platforms which require an FCOG, indicates the maximum number of byte offsets specifiable for each offset group. |
| INT rlPolicyNumberOfOffsetsPerOmpcGroup | 1.3.6.1.4.1.9.6.1.101.59.2.1.4 | INTEGER | read-only | indicates the maximum number of byte offsets specifiable for each Ompc offset group. |
| INT rlPolicyNumberOfServiceClassesSupported | 1.3.6.1.4.1.9.6.1.101.59.6.1.1 | INTEGER | read-only | Indicates the number of service classes supported on each port of the platform. Service classes can be neither created nor destroyed. |
| INT rlPolicyOldDscp | 1.3.6.1.4.1.9.6.1.101.59.10.4.1.1 | INTEGER | read-only | Old DSCP. |
| INT rlPolicyOMPCCondition | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.7 | INTEGER | read-write | These define the operation carried out on the two 'operands' (frame and pattern), i.e. Bigger means that frame bits should be bigger than pattern bits. The permitted values are according to rlPolicyOMPCPermittedOperators parameter, if this OMPC is used by an entry in the rlPolicyClassifierTable whose rlPolicyClassifierType is a protocol for which predefined offsets in rlPolicyFlowClassificationOffsetsTable are required. rlPolicyRequiredOffsetGroups indicates for which protocols there is such a requirement. |
| STR rlPolicyOMPCDescription | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.8 | DisplayString | read-write | Free text specifing the nature of this OMPC. |
| rlPolicyOMPCEntry | 1.3.6.1.4.1.9.6.1.101.59.2.3.1 | not-accessible | Each classification statement consists of the following parameters | |
| RLP rlPolicyOMPCGroupType | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.1 | RlPolicyGroupType | read-only | Specifies a classifier type for which offset bytes can be specified. |
| INT rlPolicyOMPCIndex | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.2 | INTEGER | read-only | Index into the OMPC Table. |
| OCT rlPolicyOMPCMask | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.5 | OCTET STRING | read-write | Specifies which bits of the rlPolicyOMPCPattern field are significant for packet comparison. The length of the mask, in case of 'bigger' or 'smaller' rlPolicyOMPCCondition, is limited by rlPolicyMaxOMPCLengthForBiggerSmallerOperation. |
| INT rlPolicyOmpcMaximumOffset | 1.3.6.1.4.1.9.6.1.101.59.2.1.5 | INTEGER | read-only | Indicates the maximum value of a byte offset in a Ompc Group. If 0, there is no limit. |
| INT rlPolicyOMPCOffset | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.3 | INTEGER | read-write | Specifies the offset within the frame (in bytes) from the layer according to rlPolicyGroupType. The limitation of this field is according to the rlPolicyFlowClassificationOffsetGroupMaximumOffset parameter if this OMPC is used by an entry in the rlPolicyClassifierTable whose rlPolicyClassifierType is a protocol for which predefined offsets in rlPolicyFlowClassificationOffsetsTable are required. rlPolicyRequiredOffsetGroups indicates for which protocols there is such a requirement. |
| INT rlPolicyOMPCOffsetType | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.4 | INTEGER | read-write | Indicates whether the offset should be interpreted as relative to the beginning of L2 or the beginning of L3 |
| OCT rlPolicyOMPCPattern | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.6 | OCTET STRING | read-write | Describes the mask field. The length of this object must be equal to the length of rlPolicyOMPCMask. |
| OCT rlPolicyOMPCPermittedOperators | 1.3.6.1.4.1.9.6.1.101.59.2.1.6 | OCTET STRING | read-only | A bit mask indicating which operators are permissable in an OMPC: ---------- |87654321| ---------- 1 - equal operator permitted 2 - not-equal operator permitted 3 - greater-than operator permitted 4 - less-than operator permitted |
| ROW rlPolicyOMPCStatus | 1.3.6.1.4.1.9.6.1.101.59.2.3.1.9 | RowStatus | read-write | The status of a table entry. It is used to delete an entry from this table. |
| rlPolicyOMPCTable | 1.3.6.1.4.1.9.6.1.101.59.2.3 | not-accessible | The table of OMPC statements. | |
| STA rlPolicyOutQueueStatisticsCntrNumOfBits | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.12 | StatisticsCntrNumOfBitsType | read-only | Counter size in bits for the counter. |
| C64 rlPolicyOutQueueStatisticsCounterAllValue | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.11 | Counter64 | read-only | The counter for all traffic value. |
| C64 rlPolicyOutQueueStatisticsCounterTailDropValue | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.10 | Counter64 | read-only | The counter for tail dropped value. |
| INT rlPolicyOutQueueStatisticsCountrID | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.1 | INTEGER | read-only | Counter id, the key of the table. |
| STA rlPolicyOutQueueStatisticsDP | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.8 | StatisticsDPType | read-write | Drop Precedence for which the flow is counted. |
| T/F rlPolicyOutQueueStatisticsDPAll | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.9 | TruthValue | read-write | Indication for whether the DP is configured as range of all the DPs |
| rlPolicyOutQueueStatisticsEntry | 1.3.6.1.4.1.9.6.1.101.59.12.2.1 | not-accessible | Each entry includes port, vlan, queue, drop precedence and counter value. | |
| POR rlPolicyOutQueueStatisticsIfIndexList | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.2 | PortList | read-write | Port for which the flow is counted. |
| T/F rlPolicyOutQueueStatisticsPortAll | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.3 | TruthValue | read-write | Indication for whether the port is configured as range of all the ports |
| INT rlPolicyOutQueueStatisticsQueue | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.6 | INTEGER | read-write | Queue for which the flow is counted. |
| T/F rlPolicyOutQueueStatisticsQueueAll | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.7 | TruthValue | read-write | Indication for whether the Queue is configured as range of all the Queues |
| ROW rlPolicyOutQueueStatisticsStatus | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.13 | RowStatus | read-write | The status of a table entry. It is used to delete an entry from this table. |
| rlPolicyOutQueueStatisticsTable | 1.3.6.1.4.1.9.6.1.101.59.12.2 | not-accessible | Each entry in this table describes counter per any permutation of Port/VLAN/Queue/Drop Precedence . Each of the above can a group off 'All'. The index is port represent by rlPolicyOutQueueStatisticsCountrID. In each entry there are fields representing whether the counter is enabled and counters value. | |
| INT rlPolicyOutQueueStatisticsVlan | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.4 | INTEGER | read-write | VLAN for which the flow is counted. |
| T/F rlPolicyOutQueueStatisticsVlanAll | 1.3.6.1.4.1.9.6.1.101.59.12.2.1.5 | TruthValue | read-write | Indication for whether the Vlan is configured as range of all the Vlans |
| STA rlPolicyPolicyStatisticsCntrSize | 1.3.6.1.4.1.9.6.1.101.59.12.1.1.3 | StatisticsCntrNumOfBitsType | read-only | Counter size in bits. |
| C64 rlPolicyPolicyStatisticsCounterValue | 1.3.6.1.4.1.9.6.1.101.59.12.1.1.5 | Counter64 | read-only | Counter value. |
| T/F rlPolicyPolicyStatisticsEnableCounting | 1.3.6.1.4.1.9.6.1.101.59.12.1.1.4 | TruthValue | read-write | Indication whether the counter is enabled. |
| INT rlPolicyPortCfgCbsPortRateLimit | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.14 | INTEGER | read-write | The CBS for the port Rate Limit. N/A when the Rate Limit is disabled. UNITS bytes |
| INT rlPolicyPortCfgCbsPortShaper | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.11 | INTEGER | read-write | The CBS for the port shaper. N/A when the shper is disabled. UNITS bytes |
| OID rlPolicyPortCfgCbsQueueShaper | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.8 | OBJECT IDENTIFIER | read-write | The CBS for the Queue shaper. N/A when the shper is disabled. UNITS bytes |
| INT rlPolicyPortCfgCirPortRateLimit | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.13 | INTEGER | read-write | The CIR for the port Rate limit. N/A when the Rate limit is disabled UNITS bps bits per second |
| INT rlPolicyPortCfgCirPortShaper | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.10 | INTEGER | read-write | The CIR for the port shaper. N/A when the shper is disabled UNITS bps bits per second |
| OID rlPolicyPortCfgCirQueueShaper | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.7 | OBJECT IDENTIFIER | read-write | The CIR for the Queue shaper. N/A when the shper is disabled UNITS bps bits per second |
| rlPolicyPortCfgEntry | 1.3.6.1.4.1.9.6.1.101.59.6.6.1 | not-accessible | Configuration parameters for each port/service class. | |
| NUM rlPolicyPortCfgIfIndex | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.1 | InterfaceIndex | read-only | Interface index. |
| OID rlPolicyPortCfgMaximalBandwidth | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.3 | OBJECT IDENTIFIER | read-write | The list of objects contain parameters at Precents type for the maximal bandwidth to this port/service class at SP . The OID length is based on the number of the service class number, every OID define parameter of service class. |
| OID rlPolicyPortCfgMinimalBandwidth | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.2 | OBJECT IDENTIFIER | read-write | The list of objects contain parameters at Precents type for the minimal bandwidth to this port/service class at WWR . The OID length is based on the number of the service class number, every OID define parameter of service class. |
| T/F rlPolicyPortCfgPortRateLimitStatus | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.12 | TruthValue | read-write | If there is Rate Limit on the port |
| T/F rlPolicyPortCfgPortShaperStatus | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.9 | TruthValue | read-write | If there is shaper on the port |
| OID rlPolicyPortCfgQueueShaperStatus | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.6 | OBJECT IDENTIFIER | read-write | If there is shaper on the Queue |
| ROW rlPolicyPortCfgStatus | 1.3.6.1.4.1.9.6.1.101.59.6.6.1.4 | RowStatus | read-write | Status of this entry. |
| rlPolicyPortConfigurationTable | 1.3.6.1.4.1.9.6.1.101.59.6.6 | not-accessible | This table enables the network administrator to fine-tune the bandwidth given to each service class on each port. The values in this table will thus override those of the rlServiceClassTable (THIS TABLE IS MANAGE FROM 3SW). | |
| STA rlPolicyPortPolicyStatisticsCntrType | 1.3.6.1.4.1.9.6.1.101.59.12.1.1.2 | StatisticsCntrType | read-only | Counter type. |
| rlPolicyPortPolicyStatisticsEntry | 1.3.6.1.4.1.9.6.1.101.59.12.1.1 | not-accessible | Each entry in this table describes counter per port. The index is port represent by rlIfIndex. In each entry represents counter, it's type , it's size and whether it's enabled. | |
| INT rlPolicyPortPolicyStatisticsIfIndex | 1.3.6.1.4.1.9.6.1.101.59.12.1.1.1 | INTEGER | read-write | Interface index. |
| rlPolicyPortPolicyStatisticsTable | 1.3.6.1.4.1.9.6.1.101.59.12.1 | not-accessible | This table specifies statistics counter for policies with specific actions | |
| T/F rlPolicyPortTrustAdvancedMode | 1.3.6.1.4.1.9.6.1.101.59.16.1.5 | TruthValue | read-write | This field specified whether ports are set to trused or not-trusted by default when switching to qos advanced mode. |
| L4P rlPolicyProtocolType | 1.3.6.1.4.1.9.6.1.101.59.10.2.1.1 | L4ProtType | read-only | TCP/UDP port type. |
| rlPolicyQosModeGlobalCfgEntry | 1.3.6.1.4.1.9.6.1.101.59.16.1 | not-accessible | This table responsible to set the global qos mode configuration: qos mode, qos trust mode, and if port are trusted by default in qos advanced mode. Current implemnetaion assumes only one entry exist. | |
| rlPolicyQosModeGlobalCfgTable | 1.3.6.1.4.1.9.6.1.101.59.16 | not-accessible | This table responsible to set the global qos mode configuration: qos mode, qos trust mode, and if port are trusted by default in qos advanced mode. | |
| INT rlPolicyRmNewDscp | 1.3.6.1.4.1.9.6.1.101.59.10.3.1.2 | INTEGER | read-write | New DSCP. |
| INT rlPolicyRmOldDscp | 1.3.6.1.4.1.9.6.1.101.59.10.3.1.1 | INTEGER | read-only | Old DSCP. |
| rlPolicyRules | 1.3.6.1.4.1.9.6.1.101.59.3 | |||
| RLP rlPolicyRulesActionDropType | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.20 | RlPolicyRulesActionDropType | read-write | This field is valid only if rlPolicyRulesFilteringAction is not permit. Used to distinguish between Hard and Soft drop. |
| INT rlPolicyRulesActionPointer | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.13 | INTEGER | read-write | This further reference indicate on the entry at the action table, The rlPolicyRulesActionPointer points on the action table if the aggregate metering feature is supported,or if meter is not belong to data path. |
| C32 rlPolicyRulesCounter | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.12 | Counter32 | read-only | The number of packets that matched this filtering rule. |
| INT rlPolicyRulesCounterIdx | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.11 | INTEGER | read-write | If not zero, perform counting of matched packets . |
| STR rlPolicyRulesDescription | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.9 | DisplayString | read-write | Free text specifing the nature of this Rule. |
| INT rlPolicyRulesDestPortRangeEnd | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.19 | INTEGER | read-write | End port of port range for destination port. |
| INT rlPolicyRulesDestPortRangeStart | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.18 | INTEGER | read-write | Start port of port range for destination port. |
| INT rlPolicyRulesDownloadMarker | 1.3.6.1.4.1.9.6.1.101.59.3.3 | INTEGER | read-write | Indicates when rules download or removing starts and terminates. |
| C32 rlPolicyRulesDroppedPacketsEx | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.7 | Counter32 | read-only | The number of packets blocked by this filtering rule. |
| rlPolicyRulesEntry | 1.3.6.1.4.1.9.6.1.101.59.3.2.1 | not-accessible | Each multifield classification statement consists of the following parameters. | |
| INT rlPolicyRulesFilteringAction | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.6 | INTEGER | read-write | Specifies the action for the filter. Values 1-10 reserved for the System filtering implemetation; Values starting from 11 may be used for user definition about future application. |
| INT rlPolicyRulesFurtherRefPointer | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.8 | INTEGER | read-write | This further reference indicate on the entry at the metering or action table, based on the supported features. The rlPolicyRulesFurtherRefPointer points on the metering table if the metering feature is supported, if not this fields points on the Action table |
| INT rlPolicyRulesIndex | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.5 | INTEGER | read-only | Enumerates the rule index entry. |
| INT rlPolicyRulesInterfaceDirection | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.2 | INTEGER | read-only | Specifies the direction for this entry on the interface. 'inbound' traffic is operated on during receipt, while 'outbound' traffic is operated on prior to transmission. Based on the metering support: inbound available while the ingress metering supported, outbound available while egress metering supported, and none while no metering supported. |
| INT rlPolicyRulesListIndex | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.3 | INTEGER | read-only | Enumerates the rule list entry. |
| rlPolicyRulesPlatDependParams | 1.3.6.1.4.1.9.6.1.101.59.3.1 | |||
| INT rlPolicyRulesSrcPortRangeEnd | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.17 | INTEGER | read-write | End port of port range for source port. |
| INT rlPolicyRulesSrcPortRangeStart | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.16 | INTEGER | read-write | Start port of port range for source port. |
| ROW rlPolicyRulesStatus | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.10 | RowStatus | read-write | Row status of the Rules entry. |
| INT rlPolicyRulesSubListIndex | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.4 | INTEGER | read-only | Enumerates the rule sub-list entry. |
| rlPolicyRulesTable | 1.3.6.1.4.1.9.6.1.101.59.3.2 | not-accessible | The table of rules and Rules statements applied to all incoming traffic at the post-routing phase - ie. both the inPort and outPort are available for classification When Diffserv is not in effect(ie. IPX, bridging, or IP when the global option for Diffserv is off), certain table parameters are not available(see below). The DiffServ option is enabled or disabled by setting rlDiffservModeEnabled. | |
| RLP rlPolicyRulesTableType | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.1 | RlPolicyGroupType | read-only | Specifies a classifier type for which offset bytes can be specified. |
| INT rlPolicyRulesTimeRange1 | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.14 | INTEGER | read-write | Time range of the first ACL. |
| INT rlPolicyRulesTimeRange2 | 1.3.6.1.4.1.9.6.1.101.59.3.2.1.15 | INTEGER | read-write | Time range of the second ACL. |
| rlPolicyServiceClass | 1.3.6.1.4.1.9.6.1.101.59.6 | |||
| INT rlPolicyServiceClassActive8021DPri | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.7 | INTEGER | read-only | 802.1D Priority Tag that will be written to routed packets and untagged bridged packets transmitted with this service class. |
| INT rlPolicyServiceClassActiveCbsQueueShaper | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.23 | INTEGER | read-only | The CBS for the queue shaper. N/A when the shper is disabled. UNITS bytes |
| INT rlPolicyServiceClassActiveCirQueueShaper | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.22 | INTEGER | read-only | The CIR for the queue shaper. N/A when the shper is disabled UNITS bps bits per second |
| rlPolicyServiceClassActiveEntry | 1.3.6.1.4.1.9.6.1.101.59.6.5.1 | not-accessible | Each multifield classification statement consists of the following parameters | |
| INT rlPolicyServiceClassActiveIndex | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.1 | INTEGER | read-only | This enumerates the ServiceClass Active entry. |
| INT rlPolicyServiceClassActiveMaxRate | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.5 | INTEGER | read-only | Specifies either the upper limit on the throughput of the queue as a percentage of the throughput of each output port on which the service class is implemented. If zero, there is no maximum rate. This field can not be set by the user if rlDiffservModeEnabled = disabled and rlPolicyServiceClassPriority = 0 or rlDiffservModeEnabled = enabled and rlPolicyServiceClassPhbType != expeditedForwarding or rlBoundedPriorityQueueSupport = notSupported. |
| INT rlPolicyServiceClassActiveMinRate | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.4 | INTEGER | read-only | Specifies either the minimum throughput of the queue as a percentage of the throughput of each output port on which the service class is implemented. If zero, there is no minimum rate. This field can not be set by the user if rlDiffservModeEnabled = disabled and rlPolicyServiceClassPriority > 0 or rlDiffservModeEnabled = enabled and rlPolicyServiceClassPhbType = expeditedForwarding. |
| STR rlPolicyServiceClassActiveName | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.2 | DisplayString | read-only | The name given by the system administrator to the class. |
| INT rlPolicyServiceClassActivePhbType | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.3 | INTEGER | read-only | Indicates the type of Diffserv per-hop behaviour that this service class is intended to support. This object can be set by the user only in DiffServ mode (i.e. rlDiffservModeEnabled = enabled). |
| INT rlPolicyServiceClassActivePriority | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.6 | INTEGER | read-only | If non-zero, this service class will operate as a priority service class with the specified priority value. This object can not be set in Diffserv mode (i.e. rlDiffservModeEnabled = enabled), in which case rlServiceClassPhbType should be used instead. It can't be set when rlBoundedPriorityQueueSupport = notSupported as well. |
| INT rlPolicyServiceClassActiveRedMaxDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.12 | INTEGER | read-only | WRED Max Threshold for Drop Precedence 0. UNITS percent 0-100 |
| INT rlPolicyServiceClassActiveRedMaxDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.15 | INTEGER | read-only | WRED Max Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyServiceClassActiveRedMaxDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.18 | INTEGER | read-only | WRED Max Threshold for Drop Precedence 2. UNITS percent 0-100 |
| INT rlPolicyServiceClassActiveRedMinDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.11 | INTEGER | read-only | WRED Min Threshold for Drop Precedence 0. UNITS percent 0-100 |
| INT rlPolicyServiceClassActiveRedMinDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.14 | INTEGER | read-only | WRED Min Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyServiceClassActiveRedMinDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.17 | INTEGER | read-only | WRED Min Threshold for Drop Precedence 2. UNITS percent 0-100 |
| INT rlPolicyServiceClassActiveRedProbDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.13 | INTEGER | read-only | WRED probability for Drop Precedence 0. |
| INT rlPolicyServiceClassActiveRedProbDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.16 | INTEGER | read-only | WRED probability for Drop Precedence 1. |
| INT rlPolicyServiceClassActiveRedProbDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.19 | INTEGER | read-only | WRED probability for Drop Precedence 2. |
| INT rlPolicyServiceClassActiveRedQweight | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.20 | INTEGER | read-only | additional parameter for the WRED algorithem supporting the Queue weight exponentail factor |
| T/F rlPolicyServiceClassActiveShaperStatus | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.21 | TruthValue | read-only | If there is shaper on the Queue |
| rlPolicyServiceClassActiveTable | 1.3.6.1.4.1.9.6.1.101.59.6.5 | not-accessible | This table defines the service classes for the system ie. the queue discipline and weight characteristics that are implemented on each port unless the user configures a port specific value in .... The total number of service classes defined can not exceed rlPolicyNumberOfTransmitQueuesPerPort. | |
| INT rlPolicyServiceClassActiveTdThersholdDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.8 | INTEGER | read-only | Tail Drop Threshold for Drop Precedence 0. UNITS percent 0-100 |
| INT rlPolicyServiceClassActiveTdThersholdDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.9 | INTEGER | read-only | Tail Drop Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyServiceClassActiveTdThersholdDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.5.1.10 | INTEGER | read-only | Tail Drop Threshold for Drop Precedence 2. UNITS percent 0-100 |
| rlPolicyServiceClassPlatDependParams | 1.3.6.1.4.1.9.6.1.101.59.6.1 | |||
| INT rlPolicyServiceClassTentative8021DPri | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.7 | INTEGER | read-write | 802.1D Priority Tag that will be written to routed packets and untagged bridged packets transmitted with this service class. |
| INT rlPolicyServiceClassTentativeCbsQueueShaper | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.24 | INTEGER | read-write | The CBS for the Queue shaper. N/A when the shper is disabled. UNITS bytes |
| INT rlPolicyServiceClassTentativeCirQueueShaper | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.23 | INTEGER | read-write | The CIR for the Queue shaper. N/A when the shper is disabled. UNITS bps bits per second |
| rlPolicyServiceClassTentativeEntry | 1.3.6.1.4.1.9.6.1.101.59.6.4.1 | not-accessible | Each multifield classification statement consists of the following parameters | |
| INT rlPolicyServiceClassTentativeIndex | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.1 | INTEGER | read-only | This enumerates the ServiceClass Tentative entry. |
| INT rlPolicyServiceClassTentativeMaxRate | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.5 | INTEGER | read-write | Specifies either the upper limit on the throughput of the queue as a percentage of the throughput of each output port on which the service class is implemented. If zero, there is no maximum rate. This field can not be set by the user if rlDiffservModeEnabled = disabled and rlPolicyServiceClassPriority = 0 or rlDiffservModeEnabled = enabled and rlPolicyServiceClassPhbType != expeditedForwarding or rlBoundedPriorityQueueSupport = notSupported. |
| INT rlPolicyServiceClassTentativeMinRate | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.4 | INTEGER | read-write | Specifies either the minimum throughput of the queue as a percentage of the throughput of each output port on which the service class is implemented. If zero, there is no minimum rate. This field can not be set by the user if rlDiffservModeEnabled = disabled and rlPolicyServiceClassPriority > 0 or rlDiffservModeEnabled = enabled and rlPolicyServiceClassPhbType = expeditedForwarding. |
| STR rlPolicyServiceClassTentativeName | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.2 | DisplayString | read-write | The name given by the system administrator to the class. |
| INT rlPolicyServiceClassTentativePhbType | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.3 | INTEGER | read-write | Indicates the type of Diffserv per-hop behaviour that this service class is intended to support. This object can be set by the user only in DiffServ mode (i.e. rlDiffservModeEnabled = enabled). |
| INT rlPolicyServiceClassTentativePriority | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.6 | INTEGER | read-write | If non-zero, this service class will operate as a priority service class with the specified priority value. This object can not be set in Diffserv mode (i.e. rlDiffservModeEnabled = enabled), in which case rlServiceClassPhbType should be used instead. It can't be set when rlBoundedPriorityQueueSupport = notSupported as well. |
| INT rlPolicyServiceClassTentativeRedMaxDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.13 | INTEGER | read-write | WRED Max Threshold for Drop Precedence 0. UNITS percent 0-100 |
| INT rlPolicyServiceClassTentativeRedMaxDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.16 | INTEGER | read-write | WRED Max Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyServiceClassTentativeRedMaxDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.19 | INTEGER | read-write | WRED Max Threshold for Drop Precedence 2. UNITS percent 0-100 |
| INT rlPolicyServiceClassTentativeRedMinDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.12 | INTEGER | read-write | WRED Min Threshold for Drop Precedence 0. UNITS percent 0-100 |
| INT rlPolicyServiceClassTentativeRedMinDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.15 | INTEGER | read-write | WRED Min Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyServiceClassTentativeRedMinDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.18 | INTEGER | read-write | WRED Min Threshold for Drop Precedence 2. UNITS percent 0-100 |
| INT rlPolicyServiceClassTentativeRedProbDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.14 | INTEGER | read-write | WRED probability for Drop Precedence 0. |
| INT rlPolicyServiceClassTentativeRedProbDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.17 | INTEGER | read-write | WRED probability for Drop Precedence 1. |
| INT rlPolicyServiceClassTentativeRedProbDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.20 | INTEGER | read-write | WRED probability for Drop Precedence 2. |
| INT rlPolicyServiceClassTentativeRedQweight | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.21 | INTEGER | read-write | additional parameter for the WRED algorithem supporting the Queue weight exponentail factor |
| T/F rlPolicyServiceClassTentativeShaperStatus | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.22 | TruthValue | read-write | If there is shaper on the Queue |
| ROW rlPolicyServiceClassTentativeStatus | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.8 | RowStatus | read-write | Status of this entry. |
| rlPolicyServiceClassTentativeTable | 1.3.6.1.4.1.9.6.1.101.59.6.4 | not-accessible | This table defines the service classes for the system ie. the queue discipline and weight characteristics that are implemented on each port unless the user configures a port specific value in .... The total number of service classes defined can not exceed rlPolicyNumberOfTransmitQueuesPerPort. | |
| INT rlPolicyServiceClassTentativeTdThersholdDp0 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.9 | INTEGER | read-write | Tail Drop Threshold for Drop Precedence 0. UNITS percent 0-100 |
| INT rlPolicyServiceClassTentativeTdThersholdDp1 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.10 | INTEGER | read-write | Tail Drop Threshold for Drop Precedence 1. UNITS percent 0-100 |
| INT rlPolicyServiceClassTentativeTdThersholdDp2 | 1.3.6.1.4.1.9.6.1.101.59.6.4.1.11 | INTEGER | read-write | Tail Drop Threshold for Drop Precedence 2. UNITS percent 0-100 |
| INT rlPolicyServiceClassValue | 1.3.6.1.4.1.9.6.1.101.59.10.1.1.2 | INTEGER | read-write | ServiceClass value. |
| rlPolicyStatistics | 1.3.6.1.4.1.9.6.1.101.59.12 | |||
| INT rlPolicyTcpUdpPort | 1.3.6.1.4.1.9.6.1.101.59.10.2.1.2 | INTEGER | read-only | TCP/UDP port number. |
| rlPolicyTcpUdpPortServiceClassEntry | 1.3.6.1.4.1.9.6.1.101.59.10.2.1 | not-accessible | Each entry in this table describes The ServiceClass Value. The index is TCP/UDP port represent by rlPolicyTcpUdpPort | |
| ROW rlPolicyTcpUdpPortServiceClassStatus | 1.3.6.1.4.1.9.6.1.101.59.10.2.1.4 | RowStatus | read-write | The status of a table entry. It is used to delete/Add an entry from this table. |
| rlPolicyTcpUdpPortServiceClassTable | 1.3.6.1.4.1.9.6.1.101.59.10.2 | not-accessible | This table specifies TCP/UDP Port to ServiceClass map table | |
| rlPolicyTrustModeEntry | 1.3.6.1.4.1.9.6.1.101.59.10.5.1 | not-accessible | describes the ports status that belongs to the global trusted state | |
| INT rlPolicyTrustModePortNumber | 1.3.6.1.4.1.9.6.1.101.59.10.5.1.1 | INTEGER | read-only | phisical port number . |
| INT rlPolicyTrustModePortState | 1.3.6.1.4.1.9.6.1.101.59.10.5.1.2 | INTEGER | read-write | the port state for the trusted mode. the port can be enabled or disabled for the basic trust mode |
| rlPolicyTrustModeTable | 1.3.6.1.4.1.9.6.1.101.59.10.5 | not-accessible | This table specifies the port state for the trusted basic mode | |
| INT rlPolicyVlanCfgCbsPortRateLimit | 1.3.6.1.4.1.9.6.1.101.59.6.8.1.4 | INTEGER | read-write | The CBS for the port Rate Limit. N/A when the Rate Limit is disabled. UNITS bytes |
| INT rlPolicyVlanCfgCirPortRateLimit | 1.3.6.1.4.1.9.6.1.101.59.6.8.1.3 | INTEGER | read-write | The CIR for the port Rate limit. N/A when the Rate limit is disabled UNITS bps bits per second |
| rlPolicyVlanCfgEntry | 1.3.6.1.4.1.9.6.1.101.59.6.8.1 | not-accessible | Configuration parameters for each vlan. | |
| T/F rlPolicyVlanCfgPortRateLimitStatus | 1.3.6.1.4.1.9.6.1.101.59.6.8.1.2 | TruthValue | read-write | If there is Rate Limit on the vlan |
| ROW rlPolicyVlanCfgStatus | 1.3.6.1.4.1.9.6.1.101.59.6.8.1.5 | RowStatus | read-write | Status of this entry. |
| VLA rlPolicyVlanCfgVlanId | 1.3.6.1.4.1.9.6.1.101.59.6.8.1.1 | VlanId | read-only | Interface index. |
| rlPolicyVlanConfigurationTable | 1.3.6.1.4.1.9.6.1.101.59.6.8 | not-accessible | This table enables the network administrator to fine-tune the rate limit given to each vlan. The values in this table will thus override those of the rlQosIfPolicyTable (THIS TABLE IS MANAGED FROM 3SW). | |
| INT rlPolicyVptValue | 1.3.6.1.4.1.9.6.1.101.59.10.6.1.2 | INTEGER | read-write | VPT value. |
RFC description
Quality of Service (QoS) policy configuration for Cisco Small Business switches, managing traffic classification and rate limiting.
Start monitoring Cisco Small Business managed switches (CISCOSB series) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.