HMPRIV-MGMT-SNMP-MIB

All MIBs › HMPRIV-MGMT-SNMP-MIB

Organization: Hirschmann Automation and Control GmbH

Last Updated: 2012-09-04

Category: Device Management, Vendor: Belden

Description: Hirschmann private management SNMP MIB providing proprietary device configuration objects for Hirschmann legacy switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HMPRIV-MGMT-SNMP-MIB?

HMPRIV-MGMT-SNMP-MIB is a Hirschmann proprietary MIB providing private management objects for Hirschmann's modular/chassis-based industrial switch platforms. It exposes system-level product and version identification along with chassis-oriented hardware inventory, including maximum supported power supplies and fans, group/module capacity, and per-group module and port capacity tables. This gives it clear hardware-status monitoring value — an admin can determine how many power supplies and fan slots a chassis supports and cross-check against what's installed, alongside confirming the product model and firmware version running. Setting up HMPRIV-MGMT-SNMP-MIB SNMP monitoring typically involves polling these chassis inventory objects on a scheduled basis to catch power-supply or fan-slot changes that indicate a hardware fault, and as a legacy private MIB it largely stands alone but conceptually parallels standard entity/chassis MIB concepts (e.g. ENTITY-MIB) for physical inventory. It is deployed on Hirschmann's modular industrial Ethernet switch platforms used in industrial automation and rugged networking environments.

IPNetwork Monitor allows you to monitor SNMP objects defined in HMPRIV-MGMT-SNMP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Hirschmann RSPE-Expandable — current fanless managed industrial Ethernet switch (Belden)
Hirschmann MACH104-20TX-FR — current workgroup industrial switch

Monitoring Examples

An admin polling hmSysProduct and hmSysVersion identifies the exact switch model and firmware version in use. hmSysMaxPowerSupply and hmSysMaxFan reveal the chassis's designed redundancy capacity, which combined with hmSysGroupTable/hmSysGroupEntry (indexed by hmSysGroupID, reporting hmSysGroupType) shows how many module groups are actually populated. hmSysGroupModuleCapacity and hmSysModulePortCapacity help confirm a group hasn't exceeded its supported module/port count.

What Can Be Monitored

product model and firmware version
power supply capacity/redundancy
fan capacity
module group inventory
per-group module/port capacity

Imported Objects

From BRIDGE-MIB

dot1dStaticAddress

From IANA-ADDRESS-FAMILY-NUMBERS-MIB

AddressFamilyNumbers

From IF-MIB

ifIndex

OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From RMON2-MIB

TimeFilter

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
TimeTicks
enterprises

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
eagle	1.3.6.1.4.1.248.14.10.20
eagle_mguard	1.3.6.1.4.1.248.14.10.22
eagle20	1.3.6.1.4.1.248.14.10.23
eem1	1.3.6.1.4.1.248.14.10.200
hirschmann	1.3.6.1.4.1.248
INT hmAction	1.3.6.1.4.1.248.14.2.1	INTEGER	read-write	This object, when read, always returns a value of other(1). A value of reset(2) has the same effect as a power-on sequence (coldstart). Writing a value of hotRestart(10) leads to a warmstart. When set to resetStats(3), a reset of all statistic counters within the whole switch will be forced. A value of resetFDB(4) will clear the forwarding database. If set to resetARP(5), the ARP table will be flushed. The value gbl-reset(12) will result in a reset of the whole chassis. Any other value results in a badValue status code.
I32 hmActionResult	1.3.6.1.4.1.248.14.2.2	Integer32	read-only	Result of the last activated action. A value of zero indicates that the result is ok. Bits set in the result indicate error conditions.
NTF hmAddressRelearnDetectTrap	1.3.6.1.4.1.248.14.2.0.10			This trap is sent if the relearn threshold is exceeded.
hmAgent	1.3.6.1.4.1.248.14.2
hmAgentEvent	1.3.6.1.4.1.248.14.2.0			The events of hmAgent.
OCT hmAgentLoginBanner	1.3.6.1.4.1.248.14.2.17.1	OCTET STRING	read-write	The text added in this variable by the user will be display in the system login page as banner on every login into the CLI (local or remote) or when login into the system web interface. The default value is an empty string, which will not be displayed. Special meaning have the sequences '\t' and '\n' which allow the user to format the string with tabulator (t) and newline (n) format instructions.
hmAgentLoginGroup	1.3.6.1.4.1.248.14.2.17
INT hmAgentSnmpAuthenticationTrapFlag	1.3.6.1.4.1.248.14.2.13.5.1	INTEGER	read-write	Authentication Flag - Enable/Disable authentication Flag.
INT hmAgentSnmpBroadcastStormTrapFlag	1.3.6.1.4.1.248.14.2.13.5.5	INTEGER	read-write	Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery.
INT hmAgentSnmpChassisTrapFlag	1.3.6.1.4.1.248.14.2.13.5.6	INTEGER	read-write	Chassis Flag - Enable/Disable traps for hmTemperatureTrap hmModuleMapChange hmPowerSupplyTrap hmAutoconfigAdapterTrap
INT hmAgentSnmpCommunityAccessMode	1.3.6.1.4.1.248.14.2.13.2.1.5	INTEGER	read-write	The switch's Snmp Community Access Mode Access Mode - This value can be read-only or read/write. A community with a read-only access allows for switch information to be displayed. A community with a read/write access allows for configuration changes to be made and for information to be displayed.
hmAgentSnmpCommunityConfigEntry	1.3.6.1.4.1.248.14.2.13.2.1		not-accessible	Switch's SNMP Config entry
hmAgentSnmpCommunityConfigTable	1.3.6.1.4.1.248.14.2.13.2		not-accessible	A table of the switch's SNMP Config entries
STR hmAgentSnmpCommunityCreate	1.3.6.1.4.1.248.14.2.13.1	DisplayString	read-write	Creates a new SNMP Community entry. Defaults: IPAddress 0.0.0.0 IpMask 0.0.0.0 AccessMode read-only Status config
I32 hmAgentSnmpCommunityIndex	1.3.6.1.4.1.248.14.2.13.2.1.1	Integer32	read-only	The switch's Snmp Community Index
IP hmAgentSnmpCommunityIPAddress	1.3.6.1.4.1.248.14.2.13.2.1.3	IpAddress	read-write	The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.
IP hmAgentSnmpCommunityIPMask	1.3.6.1.4.1.248.14.2.13.2.1.4	IpAddress	read-write	The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255.
I32 hmAgentSnmpCommunityMaxEntries	1.3.6.1.4.1.248.14.2.13.6	Integer32	read-only	Max number of Entries in hmAgentSnmpCommunityConfigEntry
STR hmAgentSnmpCommunityName	1.3.6.1.4.1.248.14.2.13.2.1.2	DisplayString	read-write	The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 32 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored.
INT hmAgentSnmpCommunityStatus	1.3.6.1.4.1.248.14.2.13.2.1.6	INTEGER	read-write	The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP managers associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent.
hmAgentSnmpConfigGroup	1.3.6.1.4.1.248.14.2.13
INT hmAgentSnmpL2RedundancyTrapFlag	1.3.6.1.4.1.248.14.2.13.5.7	INTEGER	read-write	Chassis Flag - Enable/Disable traps hmRingRedReconfig and hmRingCplReconfig
INT hmAgentSnmpLinkUpDownTrapFlag	1.3.6.1.4.1.248.14.2.13.5.2	INTEGER	read-write	Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.
INT hmAgentSnmpLogGetRequest	1.3.6.1.4.1.248.14.2.13.8.1	INTEGER	read-write	Enable logging of SNMP GET requests.
HMA hmAgentSnmpLogGetSeverity	1.3.6.1.4.1.248.14.2.13.8.3	HmAgentLogSeverity	read-write	Define the log severity for SNMP GET requests.
hmAgentSnmpLoggingGroup	1.3.6.1.4.1.248.14.2.13.8
INT hmAgentSnmpLogSetRequest	1.3.6.1.4.1.248.14.2.13.8.2	INTEGER	read-write	Enable logging of SNMP SET requests.
HMA hmAgentSnmpLogSetSeverity	1.3.6.1.4.1.248.14.2.13.8.4	HmAgentLogSeverity	read-write	Define the log severity for SNMP SET requests.
INT hmAgentSnmpMultipleUsersTrapFlag	1.3.6.1.4.1.248.14.2.13.5.3	INTEGER	read-write	Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session.
INT hmAgentSnmpPortSecurityTrapFlag	1.3.6.1.4.1.248.14.2.13.5.8	INTEGER	read-write	PortSecurity Flag - enable/disable all port security traps.
INT hmAgentSnmpSpanningTreeTrapFlag	1.3.6.1.4.1.248.14.2.13.5.4	INTEGER	read-write	Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.
hmAgentSnmpTrapFlagsConfigGroup	1.3.6.1.4.1.248.14.2.13.5
STR hmAgentSnmpTrapReceiverCommunityName	1.3.6.1.4.1.248.14.2.13.4.1.2	DisplayString	read-write	The switch's Snmp Trap Receiver Community Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case-sensitive.
hmAgentSnmpTrapReceiverConfigEntry	1.3.6.1.4.1.248.14.2.13.4.1		not-accessible	Switch's Snmp Trace Receiver Config entry
hmAgentSnmpTrapReceiverConfigTable	1.3.6.1.4.1.248.14.2.13.4		not-accessible	Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.
STR hmAgentSnmpTrapReceiverCreate	1.3.6.1.4.1.248.14.2.13.3	DisplayString	read-write	Creates a new trap receiver entry. Defaults: IPAddress 0.0.0.0 status config
I32 hmAgentSnmpTrapReceiverIndex	1.3.6.1.4.1.248.14.2.13.4.1.1	Integer32	read-only	The switch's Snmp Trap Receiver Index
IP hmAgentSnmpTrapReceiverIPAddress	1.3.6.1.4.1.248.14.2.13.4.1.3	IpAddress	read-write	IP Address - Each IP address parameter is four integer numbers. The numbers range from 0 to 255.
I32 hmAgentSnmpTrapReceiverMaxEntries	1.3.6.1.4.1.248.14.2.13.7	Integer32	read-only	Max number of Entries in hmAgentSnmpTrapReceiverConfigEntry
INT hmAgentSnmpTrapReceiverStatus	1.3.6.1.4.1.248.14.2.13.4.1.4	INTEGER	read-write	The switch's Snmp Trap Reciever Status. active(1) - This trap receiver is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap reciever is not active; no SNMP Traps will be sent to this reciever until it's set back to active(1). config(3) - The trap reciever Status must be set to this value in order to configure it. When creating a new trap receiver entry, the Status will initially be set to this value. Note: hmAgentSnmpTrapReceiverIPAddress must be set to non-zero before changing to active(1) or notInService(2). destroy(4) - Set to this value to remove the trap receiver entry from the agent.
hmAUIGroup	1.3.6.1.4.1.248.14.1.12
INT hmAUIModuleDTEPowerMonitor	1.3.6.1.4.1.248.14.1.12.10.1.2	INTEGER	read-only	This variable shows the DTE Power Monitor DIP switch setting on the AUI module.
hmAUIModuleEntry	1.3.6.1.4.1.248.14.1.12.10.1		not-accessible	The entry of the hmAUIModuleTable.
I32 hmAUIModuleID	1.3.6.1.4.1.248.14.1.12.10.1.1	Integer32	read-only	This index is used to identify a specific module.
hmAUIModuleTable	1.3.6.1.4.1.248.14.1.12.10		not-accessible	This table contains all AUI variables that are module dependend.
INT hmAUIPortDTEPower	1.3.6.1.4.1.248.14.1.12.11.1.2	INTEGER	read-only	This variable shows the DTE Power value of the AUI port.
hmAUIPortEntry	1.3.6.1.4.1.248.14.1.12.11.1		not-accessible	The entry of the hmAUIPortTable.
I32 hmAUIPortID	1.3.6.1.4.1.248.14.1.12.11.1.1	Integer32	read-only	This index is used to identify a specific port.
INT hmAUIPortSQETest	1.3.6.1.4.1.248.14.1.12.11.1.3	INTEGER	read-only	This variable shows the SQE Test DIP switch setting on the AUI port.
hmAUIPortTable	1.3.6.1.4.1.248.14.1.12.11		not-accessible	This table contains all AUI variables that are port dependend.
hmAuthCommEntry	1.3.6.1.4.1.248.14.2.7.3.1		not-accessible	A list of SNMP Community properties.
I32 hmAuthCommIndex	1.3.6.1.4.1.248.14.2.7.3.1.1	Integer32	read-only	An index that uniquely identifies an ordered entry in the SNMP Community Table.
STR hmAuthCommName	1.3.6.1.4.1.248.14.2.7.3.1.2	DisplayString	read-write	The name of this SNMP Community Entry, e.g. public. This object can only be written.
INT hmAuthCommPerm	1.3.6.1.4.1.248.14.2.7.3.1.3	INTEGER	read-write	The Read/Write (GET/SET) permission for the community. A (1) indicates perm-ro (GET) permission. A (2) indicates perm-wr (GET/SET) permission.
INT hmAuthCommState	1.3.6.1.4.1.248.14.2.7.3.1.4	INTEGER	read-write	The state of this community entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that is no longer valid (e.g., an entry that was deleted) and should be ignored. An attempt to set a value of invalid (4) causes the agent to return SNMP_BADVALUE.
hmAuthCommTable	1.3.6.1.4.1.248.14.2.7.3		not-accessible	A list of valid SNMP Community Entries.
I32 hmAuthCommTableEntriesMax	1.3.6.1.4.1.248.14.2.7.2	Integer32	read-only	The maximum possible number of entries in the hmAuthCommTable. This value equates to the total number of communities which ly may be recognized.
hmAuthGroup	1.3.6.1.4.1.248.14.2.7
I32 hmAuthHostCommIndex	1.3.6.1.4.1.248.14.2.7.4.1.3	Integer32	read-write	The index of this SNMP Trusted Host Entry's community entry in the hmAuthCommTable.
hmAuthHostEntry	1.3.6.1.4.1.248.14.2.7.4.1		not-accessible	A list of SNMP Host properties.
I32 hmAuthHostIndex	1.3.6.1.4.1.248.14.2.7.4.1.1	Integer32	read-only	An index that uniquely identifies an ordered entry in the SNMP Trusted Host Table.
IP hmAuthHostIpAddress	1.3.6.1.4.1.248.14.2.7.4.1.4	IpAddress	read-write	The IP Address for the host. This identified host has permission to access information in this device's MIB tables, providing the SNMP security toggle is on (see hmMiscSNMPSecurity).
IP hmAuthHostIpMask	1.3.6.1.4.1.248.14.2.7.4.1.5	IpAddress	read-write	The Network Mask for the trusted Host entry.
STR hmAuthHostName	1.3.6.1.4.1.248.14.2.7.4.1.2	DisplayString	read-write	The name of this SNMP Trusted Host Entry, e.g. host1.
INT hmAuthHostState	1.3.6.1.4.1.248.14.2.7.4.1.6	INTEGER	read-write	The state of this trusted host entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that is no longer valid (e.g., an entry that was deleted) and should be ignored. An attempt to set a value of invalid (4) causes the agent to return SNMP_BADVALUE.
hmAuthHostTable	1.3.6.1.4.1.248.14.2.7.4		not-accessible	A list of valid SNMP Trusted Host Entries.
I32 hmAuthHostTableEntriesMax	1.3.6.1.4.1.248.14.2.7.1	Integer32	read-only	The maximum possible number of entries in the hmAuthHostTable. This value equates to the total number of trusted Hosts which potentially may be recognized.
STR hmAutoconfigAdapterSerialNum	1.3.6.1.4.1.248.14.2.4.200.2	DisplayString	read-only	The serial number provided by vendor (ASCII).
INT hmAutoconfigAdapterStatus	1.3.6.1.4.1.248.14.2.4.200.1	INTEGER	read-only	Status of the AutoConfiguration Adapter. notPresent(1): AutoConfiguration Adapter has not been detected. removed(2): Configuration was loaded from adapter, but adapter was removed in running mode of the agent. ok(3): Configuration of adapter and switch match. notInSync(4): Configuration of adapter and switch don't match, e.g. configuration has not yet been written into the adapter. outOfMemory(5): Configuration is too large for the adapter. wrongMachine(6): Adapter contains configuration which cannot be loaded into this machine because it was created by a different type of switch. checksumErr(7): Data in adapter fails consistency check. genericErr(8): Any other failure, e.g. hardware malfunction. autodisabled(9): USB port has been disabled for safety reasons.
NTF hmAutoconfigAdapterTrap	1.3.6.1.4.1.248.14.2.0.4			This trap reports a status change of the Autoconfiguration Adapter.
hmAutoconfigGroup	1.3.6.1.4.1.248.14.2.4.200
INT hmAutoConfigState	1.3.6.1.4.1.248.14.1.11.4.1	INTEGER	read-only	state of the configuration retrieval from a neighbour card
INT hmBcastLimiterMode	1.3.6.1.4.1.248.14.1.1.29	INTEGER	read-write	Global configuration of feature broadcast limiter. If enabled, for each port the maximum rate of broadcasts can be specified.
NTF hmBPDUGuardTrap	1.3.6.1.4.1.248.14.1.0.8			This trap is sent if on this port an BPDU guard functionality is enabled (globally or only for this port) and an (R)STP BPDU are received on this port. That means when hmIfaceStpBpduGuardStatus is set to true(1) for this port. Then IfAdminStatus for this port is set to down(2). If needed, it must be changed by hand to up(1)
hmChassis	1.3.6.1.4.1.248.14.1
hmChassisEvent	1.3.6.1.4.1.248.14.1.0			The events of hmChassis.
hmConfiguration	1.3.6.1.4.1.248.14			The Hirschmann Private MIB definitions for Platform devices.
NTF hmConfigurationChangedTrap	1.3.6.1.4.1.248.14.2.0.9			This trap is sent if the local and the running configuration doesn't match.
NTF hmConfigurationSavedTrap	1.3.6.1.4.1.248.14.2.0.8			This trap is sent after the configuration of the agent was successfully saved.
INT hmConfigurationStatus	1.3.6.1.4.1.248.14.2.4.12	INTEGER	read-only	Status of the local configuration. ok(1): Local and running configuration match. notInSync(2): Local and running configuration don't match, configuration has not yet been saved.
INT hmConfigWatchdogAdminStatus	1.3.6.1.4.1.248.14.2.4.201.1	INTEGER	read-write	Administrative status of the configuration watchdog. enable(1): start/trigger the watchdog timer disable(2): turn off the watchdog This feature provides recovery from situations where the switch cannot be reached by the management station anymore. Whenever this variable is set to enable(1), the value of hmConfigWatchdogTimeInterval is loaded into the watchdog timer. This timer must be triggered before hmConfigWatchdogTimerValue reaches 0. If the watchdog timer expires, the last saved configuration of the switch will be restored. The watchdog is triggered with MIB read and write accesses
hmConfigWatchdogGroup	1.3.6.1.4.1.248.14.2.4.201
IP hmConfigWatchdogIPAddress	1.3.6.1.4.1.248.14.2.4.201.5	IpAddress	read-only	Current IP Adress of station that triggers the watchdog.
INT hmConfigWatchdogOperStatus	1.3.6.1.4.1.248.14.2.4.201.2	INTEGER	read-only	Operational status of the configuration watchdog. enable(1): watchdog up and running disable(2): watchdog inactive
I32 hmConfigWatchdogTimeInterval	1.3.6.1.4.1.248.14.2.4.201.3	Integer32	read-write	Period of the watchdog timer in seconds.
I32 hmConfigWatchdogTimerValue	1.3.6.1.4.1.248.14.2.4.201.4	Integer32	read-only	Current count-down value of the watchdog timer in seconds.
I32 hmCpuAverageUtilization	1.3.6.1.4.1.248.14.2.15.2.2	Integer32	read-only	The average cpu utilization of the switch in percent, max. measured over the last 30 minutes.
I32 hmCpuMaxRunningProcesses	1.3.6.1.4.1.248.14.2.15.2.4	Integer32	read-only	The maximum number of processes running, max. since the last 30 minutes.
hmCpuResources	1.3.6.1.4.1.248.14.2.15.2
I32 hmCpuRunningProcesses	1.3.6.1.4.1.248.14.2.15.2.3	Integer32	read-only	The current number of processes running.
I32 hmCpuUtilization	1.3.6.1.4.1.248.14.2.15.2.1	Integer32	read-only	The current cpu utilization of the switch in percent.
MAC hmCurrentAddress	1.3.6.1.4.1.248.14.1.5.1.1	MacAddress	read-only	The destination MAC address in a frame to which this entry's filtering information applies. This object can take the value of a unicast address, a group address or the broadcast address.
OCT hmCurrentAddressEgressPorts	1.3.6.1.4.1.248.14.1.5.1.4	OCTET STRING	read-only	The complete set of ports, to which frames destined for this Group MAC Address are currently being forwarded. This includes Group MAC Addresses which were set statically or which were learnt by GMRP or some other dynamic mechanism. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.) The default value of this object is a string of ones of appropriate length.
hmCurrentAddressEntry	1.3.6.1.4.1.248.14.1.5.1		not-accessible	Filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific destination address are allowed to be forwarded.
I32 hmCurrentAddressReceivePort	1.3.6.1.4.1.248.14.1.5.1.2	Integer32	read-only	Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the bridge for which there is no other applicable entry.
OCT hmCurrentAddressStaticEgressPorts	1.3.6.1.4.1.248.14.1.5.1.3	OCTET STRING	read-only	The set of ports to which frames received from a specific port and destined for a specific MAC address, are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.) The default value of this object is a string of ones of appropriate length.
INT hmCurrentAddressStatus	1.3.6.1.4.1.248.14.1.5.1.5	INTEGER	read-only	This object indicates the status of this entry. The default value is permanent(3). other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
hmCurrentAddressTable	1.3.6.1.4.1.248.14.1.5		not-accessible	A table containing filtering information configured into the bridge by (local or network) management or dynamic by GMRP or IGMP Snooping specifying the set of ports to which frames received from specific ports and containing specific destination addresses are allowed to be forwarded. The value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast and for group/broadcast addresses.
hmDeviceMonitoringGroup	1.3.6.1.4.1.248.14.2.12
hmDevMonConfigEntry	1.3.6.1.4.1.248.14.2.12.3.1		not-accessible	Configuration of the device monitoring.
hmDevMonConfigTable	1.3.6.1.4.1.248.14.2.12.3		not-accessible	This table contains all variables to configure the behaviour of the device state.
I32 hmDevMonID	1.3.6.1.4.1.248.14.2.12.3.1.1	Integer32	read-only	This index is used to identify the associated device status (currently only one).
INT hmDevMonSenseACANotInSync	1.3.6.1.4.1.248.14.2.12.3.1.21	INTEGER	read-write	Sets the monitoring whether the configuration on ACA is in sync with the configuration in NVRAM.
INT hmDevMonSenseACARemoval	1.3.6.1.4.1.248.14.2.12.3.1.13	INTEGER	read-write	Sets the monitoring of the auto configuration adapter removal.
INT hmDevMonSenseControlLine	1.3.6.1.4.1.248.14.2.12.3.1.7	INTEGER	read-write	Sets the monitoring of the ring/network coupling.
INT hmDevMonSenseFan1State	1.3.6.1.4.1.248.14.2.12.3.1.16	INTEGER	read-write	Sets the monitoring of the cooling fan (platform dependant).
INT hmDevMonSenseLinkFailure	1.3.6.1.4.1.248.14.2.12.3.1.6	INTEGER	read-write	Sets the monitoring of the network connection(s).
INT hmDevMonSenseModuleRemoval	1.3.6.1.4.1.248.14.2.12.3.1.12	INTEGER	read-write	Sets the monitoring of module removal (platform dependant).
INT hmDevMonSensePS1State	1.3.6.1.4.1.248.14.2.12.3.1.9	INTEGER	read-write	Sets the monitoring of the power supply 1.
INT hmDevMonSensePS2State	1.3.6.1.4.1.248.14.2.12.3.1.10	INTEGER	read-write	Sets the monitoring of the power supply 2.
INT hmDevMonSensePS3State	1.3.6.1.4.1.248.14.2.12.3.1.14	INTEGER	read-write	Sets the monitoring of the power supply 3 (platform dependant).
INT hmDevMonSensePS4State	1.3.6.1.4.1.248.14.2.12.3.1.15	INTEGER	read-write	Sets the monitoring of the power supply 4 (platform dependant).
INT hmDevMonSensePS5State	1.3.6.1.4.1.248.14.2.12.3.1.17	INTEGER	read-write	Sets the monitoring of the power supply 5 (platform dependant).
INT hmDevMonSensePS6State	1.3.6.1.4.1.248.14.2.12.3.1.18	INTEGER	read-write	Sets the monitoring of the power supply 6 (platform dependant).
INT hmDevMonSensePS7State	1.3.6.1.4.1.248.14.2.12.3.1.19	INTEGER	read-write	Sets the monitoring of the power supply 7 (platform dependant).
INT hmDevMonSensePS8State	1.3.6.1.4.1.248.14.2.12.3.1.20	INTEGER	read-write	Sets the monitoring of the power supply 8 (platform dependant).
INT hmDevMonSenseRedNotGuaranteed	1.3.6.1.4.1.248.14.2.12.3.1.8	INTEGER	read-write	Sets the monitoring of the HIPER-Ring.
INT hmDevMonSenseTemperature	1.3.6.1.4.1.248.14.2.12.3.1.11	INTEGER	read-write	Sets the monitoring of the device temperature.
NTF hmDevMonStateChange	1.3.6.1.4.1.248.14.1.0.13			This trap is sent if the value of hmDevMonSwitchState changes its value. Variables included in this trap are hmDevMonSwitchState, hmDevMonTrapCause, hmDevMonTrapCauseIndex.
INT hmDevMonSwitchState	1.3.6.1.4.1.248.14.2.12.3.1.5	INTEGER	read-only	This attribute shows the current state of the device monitoring.
INT hmDevMonTrapCause	1.3.6.1.4.1.248.14.2.12.3.1.3	INTEGER	read-only	This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hmDevMonTrapCauseIndex.
I32 hmDevMonTrapCauseIndex	1.3.6.1.4.1.248.14.2.12.3.1.4	Integer32	read-only	This attribute specifies the entity which produces the trap. 1 - n: index of powersupply table / interfaces table 0: other errors
INT hmDevMonTrapEnable	1.3.6.1.4.1.248.14.2.12.3.1.2	INTEGER	read-write	Determines wether a trap shall be sent or not, when the device monitoring state changes.
hmDIPSwitchGroup	1.3.6.1.4.1.248.14.1.1.36
DIP hmDIPSwitchMICEConfig	1.3.6.1.4.1.248.14.1.1.36.2.4	DIPSwitchState	read-only	Status from DIP switch configuration. on (1) indicates DIP switch configuration is enabled. off (2) indicates DIP switch configuration is disabled.
hmDIPSwitchMICEGroup	1.3.6.1.4.1.248.14.1.1.36.2
DIP hmDIPSwitchMICERedundancyManager	1.3.6.1.4.1.248.14.1.1.36.2.1	DIPSwitchState	read-only	Status from redundancy manager DIP switch.
DIP hmDIPSwitchMICERingPort	1.3.6.1.4.1.248.14.1.1.36.2.2	DIPSwitchState	read-only	Status from ring ports DIP switch. on (1) indicates port 1 on module 1 and port 1 on module 2 are used as ring ports. off (2) indicates port 1 and 2 on module 1 are used as ring ports.
DIP hmDIPSwitchMICEStandby	1.3.6.1.4.1.248.14.1.1.36.2.3	DIPSwitchState	read-only	Status from Standby DIP switch.
hmDIPSwitchRSGroup	1.3.6.1.4.1.248.14.1.1.36.1
DIP hmDIPSwitchRSRedundancyManager	1.3.6.1.4.1.248.14.1.1.36.1.1	DIPSwitchState	read-only	Status from redundancy manager DIP switch.
DIP hmDIPSwitchRSStandby	1.3.6.1.4.1.248.14.1.1.36.1.2	DIPSwitchState	read-only	Status from Standby DIP switch.
NTF hmDuplexMismatchTrap	1.3.6.1.4.1.248.14.2.0.11			This trap indicates a possible serious situation. Check for duplex mismatch, or EMI, or too many cascaded hubs, or exceeded maximum distance at HDX port.
NTF hmDuplicateStaticAddressTrap	1.3.6.1.4.1.248.14.2.0.3			This trap is sent if a user attemps to set the same static unicast address at more than one agent of a chassis
INT hmEgressLimiterEnable	1.3.6.1.4.1.248.14.1.1.38.2.1	INTEGER	read-write	The global egress limiter can be enabled or disabled.
hmEgressLimiterGroup	1.3.6.1.4.1.248.14.1.1.38.2
INT hmEnableMeasurement	1.3.6.1.4.1.248.14.2.15.1	INTEGER	read-write	Enable or disable the resources measurement If disabled, the task - needed for measurement - is also deleted.
INT hmEtherNetIPAdminStatus	1.3.6.1.4.1.248.14.2.16.3.1	INTEGER	read-write	Enables/disables the EtherNet/IP(TM) functionality on this device. If disabled(2), the EtherNet/IP protocol is deactivated, but the EtherNet/IP MIBs can be accessed. The default value is disabled.
STR hmEtherNetIPCatalogName	1.3.6.1.4.1.248.14.2.16.3.7	DisplayString	read-only	Read the catolog name as provided in the EDS file for EtherNet/IP(TM). The size is restricted to 255 Characters.
hmEthernetIPConfigGroup	1.3.6.1.4.1.248.14.2.16.3
I32 hmEtherNetIPConnEstablished	1.3.6.1.4.1.248.14.2.16.4.1	Integer32	read-only	Statistics: number of connections that have been established within EtherNet/IP.
I32 hmEtherNetIPConnTimeouts	1.3.6.1.4.1.248.14.2.16.4.2	Integer32	read-only	Statistics: number of connection timeouts that have been occurred within EtherNet/IP.
I32 hmEtherNetIPErrorCode	1.3.6.1.4.1.248.14.2.16.3.2	Integer32	read-only	Read the error code within EtherNet/IP(TM) action.
I32 hmEtherNetIPProductCode	1.3.6.1.4.1.248.14.2.16.3.3	Integer32	read-only	Read the Product Code as shown in the Identity Object of EtherNet/IP(TM). Values 1 .. 65635 are valid product codes.
STR hmEtherNetIPProductName	1.3.6.1.4.1.248.14.2.16.3.6	DisplayString	read-only	Read the product name as shown in the Identity Object of EtherNet/IP(TM). The size is restricted to 32 Characters.
I32 hmEtherNetIPRevisionMajor	1.3.6.1.4.1.248.14.2.16.3.4	Integer32	read-only	Read the major revision number as shown in the Identity Object of EtherNet/IP(TM). Values 1 .. 255 are valid revisions.
I32 hmEtherNetIPRevisionMinor	1.3.6.1.4.1.248.14.2.16.3.5	Integer32	read-only	Read the minor revision number as shown in the Identity Object of EtherNet/IP(TM). Values 1 .. 255 are valid revisions.
hmEthernetIPStatisticsGroup	1.3.6.1.4.1.248.14.2.16.4
I32 hmEtherNetIPVendorObjRequests	1.3.6.1.4.1.248.14.2.16.4.3	Integer32	read-only	Statistics: number of requests to the vendor specific objects within EtherNet/IP.
NTF hmFan	1.3.6.1.4.1.248.14.1.0.3			This trap is sent if the value of hmFanCtrl changes.
hmFanEntry	1.3.6.1.4.1.248.14.1.3.1		not-accessible	The entry of the hmFanTable.
I32 hmFanID	1.3.6.1.4.1.248.14.1.3.1.2	Integer32	read-only	This Index is used to identify the associated fan.
INT hmFanState	1.3.6.1.4.1.248.14.1.3.1.3	INTEGER	read-only	Indicates the operational state of the associated fan.
I32 hmFanSysID	1.3.6.1.4.1.248.14.1.3.1.1	Integer32	read-only	The value of SysID is assigned so as to uniquely identify a chassis among the subordinate managed objects of the system.
hmFanTable	1.3.6.1.4.1.248.14.1.3		not-accessible	This table contains all variables related to the fan units of the chassis/switch. For each fan slot exists one instance.
INT hmFSAction	1.3.6.1.4.1.248.14.2.4.6	INTEGER	read-write	This object, when read, always returns a value of other (1). When set to update (2), the updatefile specified by hmFSUpdFileName will be loaded. config-load (3) will load the configuration stored in the local flash. config-save (4) will write the present configuration to the flash. config-load-remote (5) will load the configuration stored in a file specified by hmFSConfigFileName (which may be in binary or script format). config-save-remote (6) will save the present configuration in a file specified by hmFSConfigFileName. log-save (7) will save the local logfile to a file specified with hmFSLogFileName. config-load-default (8) will restore the default settings and set-to-factory (9) will apply the factory settings to the system and save the configuration to flash. log-clear (10) will clear the logfile of the agent. gbl-update (12) will perform a software update of the whole chassis. config-load-backup (13) loads an automatically saved backup configuration config-remote-and-save (15) loads a configuration via tftp and saves it to the flash. toggleImage (20) switches between main and backup software image to be active (so it will be loaded after the next coldstart). config-save-remote-script (21) saves the current configuration in script format to the file specified by hmFSConfigFileName. Any other value results in a badValue status code.
INT hmFSActionResult	1.3.6.1.4.1.248.14.2.4.8	INTEGER	read-only	Result of the last activated action.
INT hmFSBootConfiguration	1.3.6.1.4.1.248.14.2.4.9	INTEGER	read-write	By setting this MIB variable the user can control which configuration should be read during system initialization: default(1) : boot with factory settings local(2) : boot with locally stored configuration
STR hmFSConfFileName	1.3.6.1.4.1.248.14.2.4.2	DisplayString	read-write	Full specified name of the configuration file e.g. tftp://192.9.200.1/cfg/config1.sav .
TIK hmFSFileDate	1.3.6.1.4.1.248.14.2.4.100.1.4	TimeTicks	read-only	date in UNIX format (seconds since 1 jan 1970)
hmFSFileEntry	1.3.6.1.4.1.248.14.2.4.100.1		not-accessible	The entry of the hmFSFileTable.
I32 hmFSFileID	1.3.6.1.4.1.248.14.2.4.100.1.1	Integer32	read-only	This index is used to identify the associated file
STR hmFSFileName	1.3.6.1.4.1.248.14.2.4.100.1.2	DisplayString	read-only	file name excluding path
I32 hmFSFileSize	1.3.6.1.4.1.248.14.2.4.100.1.3	Integer32	read-only	file size in bytes
hmFSFileTable	1.3.6.1.4.1.248.14.2.4.100		not-accessible	a directory of the internal file system
STR hmFSLastMessage	1.3.6.1.4.1.248.14.2.4.11	DisplayString	read-only	error message of the last hmFSAction performed. If there was no error encountered, the value of this variable will be 'OK'
STR hmFSLogFileName	1.3.6.1.4.1.248.14.2.4.3	DisplayString	read-write	Local or full specified url of the log file. If value is local, the log will be written to the flash. e.g. tftp://192.9.200.1/log/log300599.log or local.
INT hmFSRunningConfiguration	1.3.6.1.4.1.248.14.2.4.10	INTEGER	read-write	By setting this MIB variable the user can control which configuration should be read after switch initialization: boot(1) : the one which is selected by hmFSBootConfiguration local(2) : boot with locally stored configuration remote(3) : use the remotely stored configuration according to hmFSConfFileName
hmFSTable	1.3.6.1.4.1.248.14.2.4
STR hmFSTPPassword	1.3.6.1.4.1.248.14.2.4.5	DisplayString	read-write	password for the used file transport protocol.
STR hmFSUpdFileName	1.3.6.1.4.1.248.14.2.4.1	DisplayString	read-write	Full specified filename of the update file e.g. tftp://192.9.200.1/upd/bootrom.v3 .
STR hmFSUserName	1.3.6.1.4.1.248.14.2.4.4	DisplayString	read-write	login name for the used file transport protocol.
hmFwdPriorityConfiguration	1.3.6.1.4.1.248.14.1.4
hmGMRP	1.3.6.1.4.1.248.14.2.10.2.1
hmGMRPGroup	1.3.6.1.4.1.248.14.2.10.2
INT hmGmrpUnknownMode	1.3.6.1.4.1.248.14.2.10.2.1.1	INTEGER	read-write	Sets the mode how unknown multicast packets will be treated. The default value is flood(2).
NTF hmGroupMapChange	1.3.6.1.4.1.248.14.1.0.1			This trap is sent when a change occurs in the group structure of a switch. This occurs only when a group is logically removed from or added to a switch. The varBind list contains the updated value of the hmSysGroupMap variable. hmNeighbourSlot identifies the related slot. hmNeighbourIpAddress shows whether a group was logically removed (0.0.0.0) or added (correct ipAddress).
INT hmIfaceAction	1.3.6.1.4.1.248.14.1.1.11.1.5	INTEGER	read-write	This object, when read, always returns a value of noAction(1). When set to resetStats(2), a reset of all statistic counters within this interfacecard will be forced.
I32 hmIfaceBcastLimit	1.3.6.1.4.1.248.14.1.1.11.1.12	Integer32	read-write	Broadcast rate: maximum number of broadcasts to be sent on this port within one second, use 0 for no limitation.
INT hmIfaceCableCrossing	1.3.6.1.4.1.248.14.1.1.11.1.27	INTEGER	read-write	This variable configures the cable crossing on twisted pair cables. When set to 'enable', the port uses the crossover mode. When set to 'disable', the port does not use the crossover mode. 'Unsupported' is shown, if a port does not support cable crossing. It is not possible to set 'unsupported' to any type of port.
I32 hmIfaceCapability	1.3.6.1.4.1.248.14.1.1.11.1.17	Integer32	read-only	Capability of the interface coded as an integer value with each bit representing a special capability. Meaning of the bits: Bit 0: cabletest capability Bit 1: realtime capability according to IEEE 1588.
INT hmIfaceEgressLimiterCalculationMode	1.3.6.1.4.1.248.14.1.1.11.1.22	INTEGER	read-write	The egress limiter can measure the traffic on a bytes per second or on a packets per second basis. The limiter calculation mode is hardware dependend. Not all modes are available on every hardware.
INT hmIfaceEgressLimiterMode	1.3.6.1.4.1.248.14.1.1.11.1.21	INTEGER	read-write	The egress limiter can work in different modes. Mode all limits the complete egress traffic. Mode bc limits only the egress broadcast traffic. Mode bc_mc limits the egress broadcast and multicast traffic. Mode bc_mc_uuc limits the egress broadcast, multicast and unknown unicast traffic. The limiter is hardware dependend. Not all modes are available on every hardware.
I32 hmIfaceEgressLimiterRate	1.3.6.1.4.1.248.14.1.1.11.1.23	Integer32	read-write	The rate of the egress limiter. The value 0 disables the limiter.
INT hmIfaceFlowControl	1.3.6.1.4.1.248.14.1.1.11.1.7	INTEGER	read-write	Enables or disables flow control per port
I32 hmIfaceGroupID	1.3.6.1.4.1.248.14.1.1.11.1.1	Integer32	read-only	index to identify an interface card. This value is never greater than hmSysGroupCapacity.
I32 hmIfaceID	1.3.6.1.4.1.248.14.1.1.11.1.2	Integer32	read-only	index to identify an interface within an interface card.
INT hmIfaceIngressLimiterCalculationMode	1.3.6.1.4.1.248.14.1.1.11.1.19	INTEGER	read-write	The ingress limiter can measure the traffic on a bytes per second or on a packets per second basis. The limiter calculation mode is hardware dependend. Not all modes are available on every hardware.
INT hmIfaceIngressLimiterMode	1.3.6.1.4.1.248.14.1.1.11.1.18	INTEGER	read-write	The ingress limiter can work in different modes. Mode all limits the complete ingress traffic. Mode bc limits only the ingress broadcast traffic. Mode bc_mc limits the ingress broadcast and multicast traffic. Mode bc_mc_uuc limits the ingress broadcast, multicast and unknown unicast traffic. The limiter is hardware dependend. Not all modes are available on every hardware.
I32 hmIfaceIngressLimiterRate	1.3.6.1.4.1.248.14.1.1.11.1.20	Integer32	read-write	The rate of the ingress limiter. The value 0 disables the limiter.
INT hmIfaceLinkType	1.3.6.1.4.1.248.14.1.1.11.1.4	INTEGER	read-write	Describes the link type of the interface.
STR hmIfaceName	1.3.6.1.4.1.248.14.1.1.11.1.9	DisplayString	read-write	User configurable textual description of the interface. On devices which support Power over Ethernet (IEEE 802.af), this object is mapped to pethPsePortType of the RFC3621 MIB.
MAC hmIfaceNextHopMacAddress	1.3.6.1.4.1.248.14.1.1.11.1.6	MacAddress	read-only	The macaddress of the next switch agent reachable via this interface. If the value is 0:0:0:0:0:0, no other switch is seen via this interface.
INT hmIfacePhyFastLinkDetection	1.3.6.1.4.1.248.14.1.1.11.1.28	INTEGER	read-write	This variable configures the PHY specific fast link detection feature on this port. 'Unsupported' is shown, if a port does not support this feature. It is not possible to set 'unsupported' to any type of port.
I32 hmIfacePriorityThreshold	1.3.6.1.4.1.248.14.1.1.11.1.8	Integer32	read-write	This object is used to support the dot1dTrafficClassTable. It defines the thresholds of the available priority-classes. Starting at MACH Release 2.20 this variable is not used any more.
INT hmIfacePrioTOSEnable	1.3.6.1.4.1.248.14.1.1.11.1.11	INTEGER	read-write	Enable or disable Priority setting from IP TOS field.
INT hmIfaceStpBpduGuardEnable	1.3.6.1.4.1.248.14.1.1.11.1.15	INTEGER	read-write	Enabled or disabled the BPDU guard functionality per port. If BPDU guard functionality are global enabled (hmSysStpBPDUGuardEnable=enable(1)), and BPDU guard are enabled per port (hmIfaceStpBpduGuardEnable=enable(1)) and (R)STP are globally enabled and an BPDU are received on the port, then hmIfaceStpBpduGuardStatus is set to true(1) for this port and IfAdminStatus for this port is set to down(2). Variable hmIfaceStpBpduGuardStatus can be reset to their original value (=false) with switching BPDU guard functionality globally off. IfAdminStatus can be reset to to their original values up() only manually.
INT hmIfaceStpBpduGuardStatus	1.3.6.1.4.1.248.14.1.1.11.1.16	INTEGER	read-only	Advertised the state of BPDU guard functionality for this port. If BPDU guard functionality fot this port is disabled or guard functionality is enabled, but no BPDUs are received on this port, then hmIfaceStpBpduGuardStatus is set to false(2) for this port. If BPDU is received on an port with enabled BPDU guard functionality for this port (hmIfaceStpBpduGuardEnable=enable(1)) and globally (hmSysStpBPDUGuardEnable=enable(1)) then hmIfaceStpBpduGuardStatus is set to true(1) and additionally IfAdminStatus for this port is set to down(2). Variable hmIfaceStpBpduGuardStatus can be reset (to their original values (=false)) with switching BPDU guard functionality globally off. IfAdminStatus can be again reset to to their original values up() only manually.
INT hmIfaceStpEnable	1.3.6.1.4.1.248.14.1.1.11.1.3	INTEGER	read-write	Enable or disable spanning tree protocol.
I32 hmIfaceTrunkID	1.3.6.1.4.1.248.14.1.1.11.1.10	Integer32	read-write	If the value of this variable is greater 0 then it belongs to the link aggregation instance with the same index. If the value is 0 no link aggregation uses this interface.
I32 hmIfaceUtilization	1.3.6.1.4.1.248.14.1.1.11.1.13	Integer32	read-only	The best estimate of the mean physical layer network utilization on this interface during the last sampling interval, in hundredths of a percent. The first historyControlInterval (rfc1757) of this interface is used as sampling interval.
T/F hmIfaceUtilizationAlarmCondition	1.3.6.1.4.1.248.14.1.1.11.1.26	TruthValue	read-only	The alarm condition is given (true), if the given hmIfaceUtilizationAlarmUpperThreshold limit is exceeded by the interface utilization. The alarm condition will be removed, when the interface utilization falls below the hmIfaceUtilizationAlarmLowerThreshold.
I32 hmIfaceUtilizationAlarmLowerThreshold	1.3.6.1.4.1.248.14.1.1.11.1.25	Integer32	read-write	Surveys the interface utilization hmInfaceUtilization and removes the alarm condition for this interfaces, if the utilization value is below the given limit. A value of 0 disables the alarm removal.
I32 hmIfaceUtilizationAlarmUpperThreshold	1.3.6.1.4.1.248.14.1.1.11.1.24	Integer32	read-write	Surveys the interface utilization hmIfaceUtilization and generates an alarm for this interfaces, if the given limit is exceeded. A value of 0 disables the alarm generation.
I32 hmIfaceUtilizationControlInterval	1.3.6.1.4.1.248.14.1.1.11.1.14	Integer32	read-only	The interval in seconds over which the data is sampled for hmIfaceUtilization. This interval can be any number of seconds between 1 and 3600 (1 hour). The first historyControlInterval (rfc1757) of this interface is used as sampling interval.
NTF hmIfaceUtilizationTrap	1.3.6.1.4.1.248.14.1.0.12			This trap is sent if the value of hmIfaceUtilization exceeds or falls back below the interface untilization threshholds hmIfaceUtilizationAlarmConditionThreshold and hmIfaceUtilizationAlarmRemovalThreshold.
hmIGMPGroup	1.3.6.1.4.1.248.14.2.10.1
hmIGMPQuerierGroup	1.3.6.1.4.1.248.14.2.10.1.2.100
I32 hmIGMPQuerierMaxResponseTime	1.3.6.1.4.1.248.14.2.10.1.2.100.4	Integer32	read-write	The maximum query response time in seconds advertised in IGMP v2 queries on this VLAN if the switch is the querier. Smaller values allow a switch to prune groups faster. So it is the maximum response time inserted into the general periodic queries. This variable enables the tuning of the burstiness of the IGMP traffic. If it is increased the responses have a larger time span in which to be generated by the hosts. The default is 10 seconds and the range is 1 to 3598 seconds.
INT hmIGMPQuerierMode	1.3.6.1.4.1.248.14.2.10.1.2.100.2	INTEGER	read-only	Shows the current mode of the IGMP Querier.
I32 hmIGMPQuerierProtocolVersion	1.3.6.1.4.1.248.14.2.10.1.2.100.5	Integer32	read-write	The Querier protocol version. The default is version 2.
INT hmIGMPQuerierStatus	1.3.6.1.4.1.248.14.2.10.1.2.100.1	INTEGER	read-write	Enables/disables IGMP Querier on this device. IGMP queries are only sent when hmIGMPSnoopStatus is also set. The default value is disable.
I32 hmIGMPQuerierTransmitInterval	1.3.6.1.4.1.248.14.2.10.1.2.100.3	Integer32	read-write	The frequency at which IGMP general query packets are transmitted by the querying switch in seconds. So this is the time between general periodic queries being sent out of the switch when it is acting as the IGMP querier. Large values lead to IGMP queries being sent less often. The default is 125 seconds and the range is 2 to 3599 seconds.
hmIGMPSnoop	1.3.6.1.4.1.248.14.2.10.1.2
I32 hmIGMPSnoopAgingTime	1.3.6.1.4.1.248.14.2.10.1.2.2	Integer32	read-write	The timeout period in seconds for aging out Multicast Groups dynamically learned with IGMP Snooping. Note that aging operates on a per interface per multicast group basis. This interval is also used to age out ports that have received IGMP Router Query PDUs. The default is 260 seconds and the range is 3 to 3600 seconds.
MAC hmIGMPSnoopFilterAddress	1.3.6.1.4.1.248.14.2.10.1.2.11.1.2	MacAddress	not-accessible	The multicast destination MAC address in a frame to which this entry's filtering information applies.
hmIGMPSnoopFilterEntry	1.3.6.1.4.1.248.14.2.10.1.2.11.1		not-accessible	The entry of the hmIGMPSnoopFilterTable.
OCT hmIGMPSnoopFilterLearntPorts	1.3.6.1.4.1.248.14.2.10.1.2.11.1.3	OCTET STRING	read-only	The set of ports, to which frames destined for this Group MAC Address learned by IGMP Snooping are currently being forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.)
hmIGMPSnoopFilterTable	1.3.6.1.4.1.248.14.2.10.1.2.11		not-accessible	A table containing the multicast filtering information on a per vlan basis learned with IGMP Snooping.
I32 hmIGMPSnoopFilterVlanIndex	1.3.6.1.4.1.248.14.2.10.1.2.11.1.1	Integer32	not-accessible	This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.
hmIGMPSnoopForwardAllEntry	1.3.6.1.4.1.248.14.2.10.1.2.12.1		not-accessible	Forwarding information for a VLAN, specifying the set of ports to which all multicasts should be forwarded, configured statically by management.
OCT hmIGMPSnoopForwardAllStaticPorts	1.3.6.1.4.1.248.14.2.10.1.2.12.1.2	OCTET STRING	read-write	The set of ports configured by management in this VLAN to which all multicast group-addressed frames learned by IGMP are to be forwarded. This value will be restored after the device is reset.
hmIGMPSnoopForwardAllTable	1.3.6.1.4.1.248.14.2.10.1.2.12		not-accessible	A table containing forwarding information for each VLAN, specifying the set of ports to which forwarding of all multicasts applies, configured statically by management. An entry appears in this table for all VLANs that are currently instantiated.
I32 hmIGMPSnoopForwardAllVlanIndex	1.3.6.1.4.1.248.14.2.10.1.2.12.1.1	Integer32	not-accessible	This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.
IP hmIGMPSnoopQuerierIPAddress	1.3.6.1.4.1.248.14.2.10.1.2.8	IpAddress	read-only	Shows the IP address of the active querier.
INT hmIGMPSnoopQuerierToPortmask	1.3.6.1.4.1.248.14.2.10.1.2.7	INTEGER	read-write	Enables or disables the addition of query ports to multicast filter portmasks.
hmIGMPSnoopQueryEntry	1.3.6.1.4.1.248.14.2.10.1.2.10.1		not-accessible	A table displaying the IGMP Router Query PDU ports. These are maintained on a per VLAN basis.
OCT hmIGMPSnoopQueryPorts	1.3.6.1.4.1.248.14.2.10.1.2.10.1.2	OCTET STRING	read-only	This read-only object displays the set of ports that have received IGMP Router Query PDUs for this VLAN as determined by the IGMP Snooping task.
OCT hmIGMPSnoopQueryStaticAutomaticPorts	1.3.6.1.4.1.248.14.2.10.1.2.13.1.3	OCTET STRING	read-only	The set of ports that are automatically learned by LLDP protocol to be IGMP-forwarding ports.
OCT hmIGMPSnoopQueryStaticAutomaticPortsEnable	1.3.6.1.4.1.248.14.2.10.1.2.13.1.4	OCTET STRING	read-write	The set of ports that are allowed to be learned automatically by LLDP protocol to be IGMP-forwarding ports.
hmIGMPSnoopQueryStaticEntry	1.3.6.1.4.1.248.14.2.10.1.2.13.1		not-accessible	The entry of the hmIGMPSnoopQueryStaticTable.
OCT hmIGMPSnoopQueryStaticPorts	1.3.6.1.4.1.248.14.2.10.1.2.13.1.2	OCTET STRING	read-write	The set of ports explicitly configured by management to be IGMP-forwarding ports.
hmIGMPSnoopQueryStaticTable	1.3.6.1.4.1.248.14.2.10.1.2.13		not-accessible	A table displaying the IGMP Static Query ports.
I32 hmIGMPSnoopQueryStaticVlanIndex	1.3.6.1.4.1.248.14.2.10.1.2.13.1.1	Integer32	not-accessible	This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.
hmIGMPSnoopQueryTable	1.3.6.1.4.1.248.14.2.10.1.2.10		not-accessible	A table displaying the IGMP Router Query PDU ports.
I32 hmIGMPSnoopQueryVlanIndex	1.3.6.1.4.1.248.14.2.10.1.2.10.1.1	Integer32	not-accessible	This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.
INT hmIGMPSnoopStatus	1.3.6.1.4.1.248.14.2.10.1.2.1	INTEGER	read-write	Enables/disables IGMP Snooping on this device. The default value is disable.
I32 hmIGMPSnoopUnknownAgingTime	1.3.6.1.4.1.248.14.2.10.1.2.4	Integer32	read-write	The timeout period in seconds approximately for aging out Unknown Multicast Groups dynamically learned with traffic snooping. The exactly value is UnknownLookupInterval/(UnknownLookupInterval-UnknownLookupResponseTime)*UnknownAgingTime. Note that aging operates on a per unknown multicast group basis. The default is 260 seconds and the range is 3 to 3600 seconds.
I32 hmIGMPSnoopUnknownLookupInterval	1.3.6.1.4.1.248.14.2.10.1.2.5	Integer32	read-write	The frequency at which Unknown Multicast Groups dynamically learned with traffic snooping are traffic checked by the switch in seconds. So this is the time between periodic traffic checking in which unknown multicast groups being aged on the switch when it is acting as Trafficsnooper. Large values lead to traffic checking less often. The default is 125 seconds and the range is 2 to 3599 seconds.
I32 hmIGMPSnoopUnknownLookupResponseTime	1.3.6.1.4.1.248.14.2.10.1.2.6	Integer32	read-write	The unknown lookup response time in seconds in which Unknown Multicast Groups dynamically learned with traffic snooping are traffic checked. So this is the time in which response traffic to the Trafficsnooper allowing the update of unknown multicast group aging timer. This variable enables the checking of bursty unknown multicast traffic. Small values lead to bad traffic checking but few snooper load and large values lead to good traffic checking but more snooper load. The default is 10 seconds and the range is 1 to 3598 seconds.
INT hmIGMPSnoopUnknownMode	1.3.6.1.4.1.248.14.2.10.1.2.3	INTEGER	read-write	Sets the mode how unknown Multicast packets will be treated. The default value is flood(2).
hmIndustrialEthernetProtocols	1.3.6.1.4.1.248.14.2.16
INT hmIngressLimiterEnable	1.3.6.1.4.1.248.14.1.1.38.1.1	INTEGER	read-write	The global ingress limiter can be enabled or disabled.
hmIngressLimiterGroup	1.3.6.1.4.1.248.14.1.1.38.1
INT hmIngressLimiterMode	1.3.6.1.4.1.248.14.1.1.38.1.2	INTEGER	read-write	The global ingress limiter can work in different modes. Mode all limits the complete ingress traffic. Mode bc limits only the ingress broadcast traffic. Mode bc_mc limits the ingress broadcast and multicast traffic. Mode bc_mc_uuc limits the ingress broadcast, multicast and unknown unicast traffic. The limiter is hardware dependend. Not all modes are available on every hardware.
INT hmIngressUnknUcLimiterCalculationMode	1.3.6.1.4.1.248.14.1.1.38.1.3.2	INTEGER	read-write	The global unknown unicast ingress limiter can measure the traffic on a bytes per second or on a packets per second basis. The limiter calculation mode is hardware dependend. Not all modes are available on every hardware.
hmIngressUnknUcLimiterGroup	1.3.6.1.4.1.248.14.1.1.38.1.3
INT hmIngressUnknUcLimiterMode	1.3.6.1.4.1.248.14.1.1.38.1.3.1	INTEGER	read-write	The global unknown unicast ingress limiter can be enabled or disabled. The limiter is hardware dependend.
I32 hmIngressUnknUcLimiterRate	1.3.6.1.4.1.248.14.1.1.38.1.3.3	Integer32	read-write	The rate of the global unknown unicast ingress limiter. The value 0 disables the limiter.
hmInterfaceEntry	1.3.6.1.4.1.248.14.1.1.11.1		not-accessible	The entry of the hmInterfaceTable.
hmInterfaceTable	1.3.6.1.4.1.248.14.1.1.11		not-accessible	This table contains variables for each interface of the switch.
hmLastAccessGroup	1.3.6.1.4.1.248.14.2.9
STR hmLastCommunity	1.3.6.1.4.1.248.14.2.9.3	DisplayString	read-only	Last community string used.
IP hmLastIpAddr	1.3.6.1.4.1.248.14.2.9.1	IpAddress	read-only	IP Address specified in the last request.
STR hmLastLoginUserName	1.3.6.1.4.1.248.14.2.9.4	DisplayString	read-only	Last login user name used.
I32 hmLastPort	1.3.6.1.4.1.248.14.2.9.2	Integer32	read-only	UDP port specified in the last request.
hmLEDGroup	1.3.6.1.4.1.248.14.1.1.35
LED hmLEDOctFault	1.3.6.1.4.1.248.14.1.1.35.2.4	LEDState	read-only	Status from the Fault LED.
hmLEDOctGroup	1.3.6.1.4.1.248.14.1.1.35.2
LED hmLEDOctPowerSupply1	1.3.6.1.4.1.248.14.1.1.35.2.1	LEDState	read-only	Status from the PowerSupply 1 LED.
LED hmLEDOctPowerSupply2	1.3.6.1.4.1.248.14.1.1.35.2.2	LEDState	read-only	Status from the PowerSupply 2 LED.
LED hmLEDOctRedundancyManager	1.3.6.1.4.1.248.14.1.1.35.2.3	LEDState	read-only	Status from the RM LED.
LED hmLEDRSFault	1.3.6.1.4.1.248.14.1.1.35.1.4	LEDState	read-only	Status from the Fault LED.
hmLEDRSGroup	1.3.6.1.4.1.248.14.1.1.35.1
LED hmLEDRSPowerSupply	1.3.6.1.4.1.248.14.1.1.35.1.1	LEDState	read-only	Status from the PowerSupply LED.
LED hmLEDRSRedundancyManager	1.3.6.1.4.1.248.14.1.1.35.1.3	LEDState	read-only	Status from the RM LED.
LED hmLEDRSRFault	1.3.6.1.4.1.248.14.1.1.35.3.4	LEDState	read-only	Status from the Fault LED.
hmLEDRSRGroup	1.3.6.1.4.1.248.14.1.1.35.3
LED hmLEDRSRPowerSupply	1.3.6.1.4.1.248.14.1.1.35.3.1	LEDState	read-only	Status from the PowerSupply LED.
LED hmLEDRSRRedundancyManager	1.3.6.1.4.1.248.14.1.1.35.3.3	LEDState	read-only	Status from the RM LED.
LED hmLEDRSRRelay1	1.3.6.1.4.1.248.14.1.1.35.3.5	LEDState	read-only	Status from the Relay1 LED.
LED hmLEDRSRRelay2	1.3.6.1.4.1.248.14.1.1.35.3.6	LEDState	read-only	Status from the Relay2 LED.
LED hmLEDRSRStandby	1.3.6.1.4.1.248.14.1.1.35.3.2	LEDState	read-only	Status from the Standby LED.
LED hmLEDRStandby	1.3.6.1.4.1.248.14.1.1.35.1.2	LEDState	read-only	Status from the Standby LED.
hmLimiterGroup	1.3.6.1.4.1.248.14.1.1.38
NTF hmLoginTrap	1.3.6.1.4.1.248.14.2.0.2			This trap is sent if a user attemps to login via telnet or serial connection. hmLastIpAddr contains the IP address of the login request. the value is 0.0.0.0, if the request was sent via serial connection. hmLastCommunity contains the used password. If the login was successfull, '******' will be sent instead.
hmMACH3ChassisExt	1.3.6.1.4.1.248.14.1.11
hmMACH3Misc	1.3.6.1.4.1.248.14.1.11.5
I32 hmMemoryAllocated	1.3.6.1.4.1.248.14.2.15.3.1	Integer32	read-only	The current allocated memory of the switch in kBytes.
I32 hmMemoryAllocatedAverage	1.3.6.1.4.1.248.14.2.15.3.3	Integer32	read-only	The average allocated memory of the switch in kBytes, measured over the last 30 minutes.
I32 hmMemoryFree	1.3.6.1.4.1.248.14.2.15.3.2	Integer32	read-only	The current free memory of the switch in kBytes.
I32 hmMemoryFreeAverage	1.3.6.1.4.1.248.14.2.15.3.4	Integer32	read-only	The average free memory of the switch in kBytes, measured over the last 30 minutes.
hmMemoryResources	1.3.6.1.4.1.248.14.2.15.3
INT hmMgmtBusSelected	1.3.6.1.4.1.248.14.1.11.2	INTEGER	read-only	this variable indicates which management bus is selected.
NTF hmModuleMapChange	1.3.6.1.4.1.248.14.1.0.7			This trap is sent when a change occurs in the module structure of a switch. This occurs only when a module is logically removed from or added to a switch. The varBind list contains the updated value of the variable hmSysGroupModuleMap.
hmMulticast	1.3.6.1.4.1.248.14.2.10
hmNeighbourAgentEntry	1.3.6.1.4.1.248.14.2.6.1		not-accessible	The entry of the hmNeighbourAgentTable.
hmNeighbourAgentTable	1.3.6.1.4.1.248.14.2.6		not-accessible	A list of the neighbour agents in a chassis
IP hmNeighbourIpAddress	1.3.6.1.4.1.248.14.2.6.1.2	IpAddress	read-only	The IP Address of the agent.
I32 hmNeighbourSlot	1.3.6.1.4.1.248.14.2.6.1.1	Integer32	read-only	An index that uniquely identifies an agent by the slot in the chassis.
OCT hmNetACDAddr	1.3.6.1.4.1.248.14.2.3.12.20.1.5	OCTET STRING	read-only	The string value used to identify the management address component associated with the local system.
hmNetACDAddrEntry	1.3.6.1.4.1.248.14.2.3.12.20.1		not-accessible	IP Address conflict detection information about a particular address on the local system kown to this agent. There may be multiple addresses configured on the system. Entries may be created and deleted in this table by the agent.
ADR hmNetACDAddrSubtype	1.3.6.1.4.1.248.14.2.3.12.20.1.3	AddressFamilyNumbers	read-only	The type of management address identifier encoding used in the associated 'hmNetACDAddr' object.
hmNetACDAddrTable	1.3.6.1.4.1.248.14.2.3.12.20		not-accessible	This table contains address conflict detection information on the local system known to this agent.
I32 hmNetACDDelay	1.3.6.1.4.1.248.14.2.3.12.5	Integer32	read-write	The maximum detection delay time in milliseconds. Time gap between arp probes.
INT hmNetACDFaultState	1.3.6.1.4.1.248.14.2.3.12.13	INTEGER	read-only	true(1) if an active address conflict is detected. false(2) if no present address conflict.
hmNetACDGroup	1.3.6.1.4.1.248.14.2.3.12
I32 hmNetACDIfId	1.3.6.1.4.1.248.14.2.3.12.20.1.9	Integer32	read-only	The integer value used to identify the interface number on the local system where the ip address conflict was detected.
MAC hmNetACDMAC	1.3.6.1.4.1.248.14.2.3.12.20.1.7	MacAddress	read-only	The physical address of the device that was detected causing the ip address conflict.
I32 hmNetACDMaxProtection	1.3.6.1.4.1.248.14.2.3.12.9	Integer32	read-write	Maximum number of frequent address protections.
NTF hmNetACDNotification	1.3.6.1.4.1.248.14.2.0.7			This trap reports an address conflict detection.
INT hmNetACDOngoingProbeStatus	1.3.6.1.4.1.248.14.2.3.12.3	INTEGER	read-write	If enabled, the device sends periodic arp probes.
I32 hmNetACDProtectInterval	1.3.6.1.4.1.248.14.2.3.12.11	Integer32	read-write	Delay in milliseconds between two protections.
I32 hmNetACDReleaseDelay	1.3.6.1.4.1.248.14.2.3.12.7	Integer32	read-write	Delay in seconds to the next arp probe cycle after an ip address conflict was detected.
INT hmNetACDStatus	1.3.6.1.4.1.248.14.2.3.12.1	INTEGER	read-write	Sets the mode of the ip address conflict detection mechanism on this device. enable(1): Both active and passive detection are active. disable(2): No detection takes place. activeDetectionOnly(3): During configuration of a local ip address the device actively probes the network for this ip address. passiveDetectionOnly(4): The device listens passively on the network if another device with an already locally configured ip address appears. In this case the own ip address is actively defended by transmitting gratituous arp's.
TIM hmNetACDTimeMark	1.3.6.1.4.1.248.14.2.3.12.20.1.1	TimeFilter	read-only	A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.
INT hmNetAction	1.3.6.1.4.1.248.14.2.3.7	INTEGER	read-write	This object, when read, always returns a value of other(1). Setting the object to activate(2) causes a reconfiguration of the IP protocol stack with the current values of hmNetLocalIPAddr, hmNetGatewayIPAddr and hmNetMask.
IP hmNetGatewayIPAddr	1.3.6.1.4.1.248.14.2.3.3	IpAddress	read-write	IP address of the default gateway. Changing this value will take effect after activating with hmNetAction.
hmNetGPSGroup	1.3.6.1.4.1.248.14.2.3.60
T/F hmNetGPSIsAvailable	1.3.6.1.4.1.248.14.2.3.60.1	TruthValue	read-only	Indicates if a GPS module is available.
T/F hmNetGPSIsSynchronized	1.3.6.1.4.1.248.14.2.3.60.2	TruthValue	read-only	Indicates if the GPS module is synchronized to the GPS signal.
INT hmNetGPSMode	1.3.6.1.4.1.248.14.2.3.60.3	INTEGER	read-write	Shows the mode of the GPS module. If hmNetGPSMode is gpsIn(1), the GPS module reads the signal from a GPS receiver in the format given in hmNetGPSTimeStringFormat. If the mode is gpsOut(2), the GPS module sends out a signal in the format given in hmNetGPSTimeStringFormat.
INT hmNetGPSTimeStringFormat	1.3.6.1.4.1.248.14.2.3.60.4	INTEGER	read-write	These are the GPS time string formats which a GPS module can read or write.
hmNetHiDiscoveryGroup	1.3.6.1.4.1.248.14.2.3.20
INT hmNetHiDiscoveryRelay	1.3.6.1.4.1.248.14.2.3.20.2	INTEGER	read-write	Relay/bridge HiDiscovery frames.
INT hmNetHiDiscoveryStatus	1.3.6.1.4.1.248.14.2.3.20.1	INTEGER	read-write	Enables/disables the HiDiscovery protocol on this device. This protocol allows a remote host to detect devices without an ip configuration. It also allows the host to set ip parameters, like the ip address, the netmask and the gateway address. If only detection and no configuration is allowed set this object to readOnly(3).
I32 hmNetIpDscpPriority	1.3.6.1.4.1.248.14.2.3.11	Integer32	read-write	IP DSCP value which is used in management replies.
IP hmNetLocalIPAddr	1.3.6.1.4.1.248.14.2.3.1	IpAddress	read-write	IP address of the management agent board. Changing this value will take effect after activating with hmNetAction.
MAC hmNetLocalPhysAddr	1.3.6.1.4.1.248.14.2.3.2	MacAddress	read-only	Physical base address (MAC-address) of the agent.
I32 hmNetLocalPhysAddrRange	1.3.6.1.4.1.248.14.2.3.9	Integer32	read-only	The number of MAC addresses reserved for this device, starting from hmNetLocalPhysAddr.
IP hmNetMask	1.3.6.1.4.1.248.14.2.3.4	IpAddress	read-write	Subnet mask. Changing this value will take effect after activating with hmNetAction.
IP hmNetNTPAnycastAddress	1.3.6.1.4.1.248.14.2.3.31.8	InetAddress	read-write	Destination address for NTP broadcasts. A broadcast, multicast or unicast address may be specified. Setting the address to 0.0.0.0 disables NTP broadcasts.
IPt hmNetNTPAnycastAddrType	1.3.6.1.4.1.248.14.2.3.31.7	InetAddressType	read-write	Address type for anycasts. Currently, only ipv4 is supported.
I32 hmNetNTPAnycastInterval	1.3.6.1.4.1.248.14.2.3.31.9	Integer32	read-write	Interval of NTP broadcast messages in seconds. NTP will round down the value to a power of 2.
hmNetNTPGroup	1.3.6.1.4.1.248.14.2.3.31
INT hmNetNTPOperation	1.3.6.1.4.1.248.14.2.3.31.1	INTEGER	read-write	Selects operation mode for NTP.
IP hmNetNTPServer1Address	1.3.6.1.4.1.248.14.2.3.31.3	InetAddress	read-write	The address of the first external time server.
IPt hmNetNTPServer1AddrType	1.3.6.1.4.1.248.14.2.3.31.2	InetAddressType	read-write	Address type for server 1. Currently, only ipv4 is supported.
IP hmNetNTPServer2Address	1.3.6.1.4.1.248.14.2.3.31.5	InetAddress	read-write	The address of the second external time server.
IPt hmNetNTPServer2AddrType	1.3.6.1.4.1.248.14.2.3.31.4	InetAddressType	read-write	Address type for server 2. Currently, only ipv4 is supported.
I32 hmNetNTPStatusCode	1.3.6.1.4.1.248.14.2.3.31.11	Integer32	read-only	Operational status of the NTP sub-system. The value is a bit mask: 1 local system clock synchronized 2 generic error (see hmNetNTPStatusText) 100 server 1 not synchronized 200 server 1 protocol error 400 server 1 not responding 800 server 1 synchronization in progress 10000 server 2 not synchronized 20000 server 2 protocol error 40000 server 2 not responding 80000 server 2 synchronization in progress (Note that all values are hexadecimal.)
STR hmNetNTPStatusText	1.3.6.1.4.1.248.14.2.3.31.10	DisplayString	read-only	Operational status of the NTP sub-system.
I32 hmNetNTPSyncInterval	1.3.6.1.4.1.248.14.2.3.31.6	Integer32	read-write	NTP synchronisation interval in seconds. NTP will round down the value to a power of 2. The protocol will use an interval between the rounded value and the next power of 2.
IP hmNetPPPBaseIPAddr	1.3.6.1.4.1.248.14.2.3.5	IpAddress	read-write	Base address of the IP address range used by the point-to-point protocol. The IP addresses hmNetPPPBaseAddress..hmNetPPPBaseAddress+4 are assigned to the client machines attached to management agents 1..5. The management agents can be reached using addresses hmNetPPPBaseAddress+10..hmNetPPPBaseAddress+14. Changing this variable on one agent automatically updates the value on the other agents in the same chassis.
IP hmNetPPPNetMask	1.3.6.1.4.1.248.14.2.3.6	IpAddress	read-write	Subnet mask used by the point-to-point protocol. Changing this variable on one agent automatically updates the value on the other agents in the same chassis.
INT hmNetPTP2AnnounceReceiptTimeout	1.3.6.1.4.1.248.14.2.3.41.2.1.6	INTEGER	read-write
PTP hmNetPTP2ClockIdentity	1.3.6.1.4.1.248.14.2.3.41.1.2	PTPClockIdentity	read-only
hmNetPTP2Configuration	1.3.6.1.4.1.248.14.2.3.41.1
I32 hmNetPTP2CurrentUtcOffset	1.3.6.1.4.1.248.14.2.3.41.1.17	Integer32	read-write
T/F hmNetPTP2CurrentUtcOffsetValid	1.3.6.1.4.1.248.14.2.3.41.1.18	TruthValue	read-write
NUM hmNetPTP2DelayAsymmetry	1.3.6.1.4.1.248.14.2.3.41.2.1.13	PTPTimeInterval	read-write
INT hmNetPTP2DelayMechanism	1.3.6.1.4.1.248.14.2.3.41.2.1.8	INTEGER	read-write
I32 hmNetPTP2DomainNumber	1.3.6.1.4.1.248.14.2.3.41.1.5	Integer32	read-write
T/F hmNetPTP2FrequencyTraceable	1.3.6.1.4.1.248.14.2.3.41.1.22	TruthValue	read-write
INT hmNetPTP2GrandmasterClockAccuracy	1.3.6.1.4.1.248.14.2.3.41.1.26	INTEGER	read-only
I32 hmNetPTP2GrandmasterClockClass	1.3.6.1.4.1.248.14.2.3.41.1.25	Integer32	read-only
PTP hmNetPTP2GrandmasterClockQuality	1.3.6.1.4.1.248.14.2.3.41.1.14	PTPClockQuality	read-only
I32 hmNetPTP2GrandmasterClockVariance	1.3.6.1.4.1.248.14.2.3.41.1.27	Integer32	read-only
PTP hmNetPTP2GrandmasterIdentity	1.3.6.1.4.1.248.14.2.3.41.1.13	PTPClockIdentity	read-only
I32 hmNetPTP2GrandmasterPriority1	1.3.6.1.4.1.248.14.2.3.41.1.15	Integer32	read-only
I32 hmNetPTP2GrandmasterPriority2	1.3.6.1.4.1.248.14.2.3.41.1.16	Integer32	read-only
hmNetPTP2Group	1.3.6.1.4.1.248.14.2.3.41
T/F hmNetPTP2Leap59	1.3.6.1.4.1.248.14.2.3.41.1.19	TruthValue	read-only
T/F hmNetPTP2Leap61	1.3.6.1.4.1.248.14.2.3.41.1.20	TruthValue	read-only
INT hmNetPTP2LogAnnounceInterval	1.3.6.1.4.1.248.14.2.3.41.2.1.5	INTEGER	read-write
I32 hmNetPTP2LogDelayReqInterval	1.3.6.1.4.1.248.14.2.3.41.2.1.3	Integer32	read-only
INT hmNetPTP2LogPdelayReqInterval	1.3.6.1.4.1.248.14.2.3.41.2.1.9	INTEGER	read-write
INT hmNetPTP2LogSyncInterval	1.3.6.1.4.1.248.14.2.3.41.2.1.7	INTEGER	read-write
NUM hmNetPTP2MeanPathDelay	1.3.6.1.4.1.248.14.2.3.41.1.8	PTPTimeInterval	read-only
INT hmNetPTP2NetworkProtocol	1.3.6.1.4.1.248.14.2.3.41.2.1.11	INTEGER	read-write
I32 hmNetPTP2ObservedParentClockPhaseChangeRate	1.3.6.1.4.1.248.14.2.3.41.1.12	Integer32	read-only
I32 hmNetPTP2ObservedParentOffsetScaledLogVariance	1.3.6.1.4.1.248.14.2.3.41.1.11	Integer32	read-only
NUM hmNetPTP2OffsetFromMaster	1.3.6.1.4.1.248.14.2.3.41.1.7	PTPTimeInterval	read-only
PTP hmNetPTP2ParentPortIdentity	1.3.6.1.4.1.248.14.2.3.41.1.9	PTPPortIdentity	read-only
T/F hmNetPTP2ParentStats	1.3.6.1.4.1.248.14.2.3.41.1.10	TruthValue	read-only
NUM hmNetPTP2PeerMeanPathDelay	1.3.6.1.4.1.248.14.2.3.41.2.1.4	PTPTimeInterval	read-only
BIT hmNetPTP2PortCapability	1.3.6.1.4.1.248.14.2.3.41.2.1.14	Bits	read-only	This object shows the capability of the ptp port.
T/F hmNetPTP2PortEnable	1.3.6.1.4.1.248.14.2.3.41.2.1.1	TruthValue	read-write
hmNetPTP2PortEntry	1.3.6.1.4.1.248.14.2.3.41.2.1		not-accessible	Entry for one port.
INT hmNetPTP2PortState	1.3.6.1.4.1.248.14.2.3.41.2.1.2	INTEGER	read-only	State of the PTP2 port intance.
hmNetPTP2PortTable	1.3.6.1.4.1.248.14.2.3.41.2		not-accessible	This table contains variables for each PTP2 port of the switch.
I32 hmNetPTP2Priority1	1.3.6.1.4.1.248.14.2.3.41.1.3	Integer32	read-write
I32 hmNetPTP2Priority2	1.3.6.1.4.1.248.14.2.3.41.1.4	Integer32	read-write
T/F hmNetPTP2PtpTimescale	1.3.6.1.4.1.248.14.2.3.41.1.23	TruthValue	read-write
I32 hmNetPTP2StepsRemoved	1.3.6.1.4.1.248.14.2.3.41.1.6	Integer32	read-only
PTP hmNetPTP2TCClockIdentity	1.3.6.1.4.1.248.14.2.3.42.1.1	PTPClockIdentity	read-only
hmNetPTP2TCConfiguration	1.3.6.1.4.1.248.14.2.3.42.1
PTP hmNetPTP2TCCurrentMaster	1.3.6.1.4.1.248.14.2.3.42.1.6	PTPPortIdentity	read-only
NUM hmNetPTP2TCDelayAsymmetry	1.3.6.1.4.1.248.14.2.3.42.2.1.5	PTPTimeInterval	read-write
INT hmNetPTP2TCDelayMechanism	1.3.6.1.4.1.248.14.2.3.42.1.2	INTEGER	read-write
T/F hmNetPTP2TCFaulty	1.3.6.1.4.1.248.14.2.3.42.2.1.3	TruthValue	read-only
hmNetPTP2TCGroup	1.3.6.1.4.1.248.14.2.3.42
INT hmNetPTP2TCLogPdelayReqInterval	1.3.6.1.4.1.248.14.2.3.42.2.1.2	INTEGER	read-write
T/F hmNetPTP2TCManagement	1.3.6.1.4.1.248.14.2.3.42.1.7	TruthValue	read-write
T/F hmNetPTP2TCMultiDomainMode	1.3.6.1.4.1.248.14.2.3.42.1.8	TruthValue	read-write
INT hmNetPTP2TCNetworkProtocol	1.3.6.1.4.1.248.14.2.3.42.1.5	INTEGER	read-write
NUM hmNetPTP2TCPeerMeanPathDelay	1.3.6.1.4.1.248.14.2.3.42.2.1.4	PTPTimeInterval	read-only
T/F hmNetPTP2TCPortEnable	1.3.6.1.4.1.248.14.2.3.42.2.1.1	TruthValue	read-write
hmNetPTP2TCPortEntry	1.3.6.1.4.1.248.14.2.3.42.2.1		not-accessible	Entry for one port.
hmNetPTP2TCPortTable	1.3.6.1.4.1.248.14.2.3.42.2		not-accessible	This table contains variables for each PTP2 TC port of the switch.
I32 hmNetPTP2TCPrimaryDomain	1.3.6.1.4.1.248.14.2.3.42.1.3	Integer32	read-write
T/F hmNetPTP2TCSyncLocalClock	1.3.6.1.4.1.248.14.2.3.42.1.9	TruthValue	read-write	Enable synchronisation of the local clock. This is only valid if syntonization is enabled
T/F hmNetPTP2TCSyntonized	1.3.6.1.4.1.248.14.2.3.42.1.4	TruthValue	read-write
I32 hmNetPTP2TCVlanID	1.3.6.1.4.1.248.14.2.3.42.1.10	Integer32	read-write	VLAN in which PTP packets are send. With a value of -1 all packets are send untagged
I32 hmNetPTP2TCVlanPriority	1.3.6.1.4.1.248.14.2.3.42.1.11	Integer32	read-write	VLAN priority of tagged ptp packets
INT hmNetPTP2TimeSource	1.3.6.1.4.1.248.14.2.3.41.1.24	INTEGER	read-write
T/F hmNetPTP2TimeTraceable	1.3.6.1.4.1.248.14.2.3.41.1.21	TruthValue	read-write
T/F hmNetPTP2TwoStepClock	1.3.6.1.4.1.248.14.2.3.41.1.1	TruthValue	read-only
INT hmNetPTP2V1Compatibility	1.3.6.1.4.1.248.14.2.3.41.2.1.12	INTEGER	read-write
INT hmNetPTP2VersionNumber	1.3.6.1.4.1.248.14.2.3.41.2.1.10	INTEGER	read-write
I32 hmNetPTP2VlanID	1.3.6.1.4.1.248.14.2.3.41.2.1.15	Integer32	read-write	VLAN in which PTP packets are send. With a value of -1 all packets are send untagged
I32 hmNetPTP2VlanPriority	1.3.6.1.4.1.248.14.2.3.41.2.1.16	Integer32	read-write	VLAN priority of tagged ptp packets
I32 hmNetPTPAbsMaxOffset	1.3.6.1.4.1.248.14.2.3.40.1.15	Integer32	read-only	This members value shall indicate the absolute value for the maximum offset between its parent and this node. The value is set to zero if the offset is the first time smaller than hmNetPTPSyncLowerBound. Offsets bigger than +/-1 second is indicated by the maximum value
INT hmNetPTPAction	1.3.6.1.4.1.248.14.2.3.40.1.2	INTEGER	read-write	Initialize the PTP Clock. Value 2: The specification initialization set shall be used. Value 3: The initialization set stored in nonvolatile storage for recovery after a power fail shall be used. Value 1: no action. In GET operations the variable always returns other(1)
OCT hmNetPTPClockIdentifier	1.3.6.1.4.1.248.14.2.3.40.1.9	OCTET STRING	read-only	The clock identifier indicates the nature and expected absolute accuracy and epoch of a given clock. Possible values are ATOM, GPS, NTP, HAND, INIT, DFLT. Values with less characters than the maximum allowed length will be padded with zero characters.
INT hmNetPTPClockMode	1.3.6.1.4.1.248.14.2.3.40.1.3	INTEGER	read-write	This members value shall indicate which clock mode is used. The ptp-mode-boundary-clock mode specifies the mode as described in the IEEE1588 standard. In the 'ptp-mode-simple-ptp' mode the device only accepts PTP sync messages, sets the time directly and no BMC algorithm will run. If the clock mode is changed, PTP will be initialized.
I32 hmNetPTPClockStratum	1.3.6.1.4.1.248.14.2.3.40.1.8	Integer32	read-only	The clock stratum, or stratum number, describes one measure of the quality of a clock. Each clock shall be characterized by a stratum number to be used by the best master clock algorithm as one parameter of clock quality. A clock stratum of 1 is the best, where the default clock stratum is 255.
I32 hmNetPTPClockVariance	1.3.6.1.4.1.248.14.2.3.40.1.10	Integer32	read-write	The clock variance reflects the inherent characteristics of the clock. It is an estimate of the local clock from a linear time scale when it is not synchronized to another PTP clock using the PTP protocol.
hmNetPTPConfiguration	1.3.6.1.4.1.248.14.2.3.40.1
I32 hmNetPTPCurrentUTCOffset	1.3.6.1.4.1.248.14.2.3.40.1.22	Integer32	read-only	UTC time differs from the TAI time by a constant offset. This offset is modified on occasion by adding or subtracting leap seconds. The current number of leap seconds is represented in PTP by the value of hmNetPTPCurrentUTCOffset.
INT hmNetPTPEnable	1.3.6.1.4.1.248.14.2.3.40.1.1	INTEGER	read-write	Enable or disable the Precision Time Protocol on this node.
I32 hmNetPTPEpochNumber	1.3.6.1.4.1.248.14.2.3.40.1.26	Integer32	read-only	The PTP epoch began at 0 hours on 1 January 1970. Times measured since this epoch are designated in this standard as PTP Seconds. When the epoch is the PTP epoch, the value of the epoch number shall be the current number of times the 32-bit seconds clock has rolled over since the PTP epoch.
MAC hmNetPTPGrandmasterUUID	1.3.6.1.4.1.248.14.2.3.40.1.21	MacAddress	read-only	The UUID of its Grandmaster. For Ethernet this is the MAC address of the management agent.
hmNetPTPGroup	1.3.6.1.4.1.248.14.2.3.40
INT hmNetPTPIsSynchronized	1.3.6.1.4.1.248.14.2.3.40.1.5	INTEGER	read-only	If the clock is synchronized to the current Master this object is set to true. Otherwise it is set to false. The clock sets this object to true, if the offset (ns) to the current Master is less than hmNetPTPSyncLowerBound. The clock sets this object to false, if the offset (ns) to the current Master is bigger than hmNetPTPSyncUpperBound.
INT hmNetPTPleap59	1.3.6.1.4.1.248.14.2.3.40.1.23	INTEGER	read-only	When TRUE the last minute of the current day will contain 59 seconds.
INT hmNetPTPleap61	1.3.6.1.4.1.248.14.2.3.40.1.24	INTEGER	read-only	When TRUE the last minute of the current day will contain 61 seconds.
I32 hmNetPTPObservedDrift	1.3.6.1.4.1.248.14.2.3.40.1.18	Integer32	read-only	Relative rate (frequency or drift) between its parent and this node in nanoseconds. Values greater than 1 second or less than -1 second are indicated by the maximum or minimum INTEGER values.
I32 hmNetPTPOffsetFromMasterNanoSecs	1.3.6.1.4.1.248.14.2.3.40.1.14	Integer32	read-only	Current offset between its parent and this node in nanoseconds. Values greater than 1 second or less than -1 second are indicated by the maximum or minimum INTEGER values.
I32 hmNetPTPOneWayDelayNanoSecs	1.3.6.1.4.1.248.14.2.3.40.1.16	Integer32	read-only	Current one_way_delay between its parent and this node in nanoseconds. Values greater than 1 second or less than -1 second are indicated by the maximum or minimum INTEGER values.
MAC hmNetPTPParentUUID	1.3.6.1.4.1.248.14.2.3.40.1.20	MacAddress	read-only	The UUID of its Parent. For Ethernet this is the MAC address of the management agent.
I32 hmNetPTPPiIntegral	1.3.6.1.4.1.248.14.2.3.40.1.19	Integer32	read-write	A digital PI servo has the following difference equation y(k) = y(k-1) + (Kp + Ki* T )* x(k) + Kp * x(k-1). This object specifies the Ki* 100000 term (integral part). Kp is 0.5. The default value of this object is 6250 that is Ki=1/16.
INT hmNetPTPPortBurstEnable	1.3.6.1.4.1.248.14.2.3.40.2.1.3	INTEGER	read-write	Controls the burst enable flag.
INT hmNetPTPPortEnable	1.3.6.1.4.1.248.14.2.3.40.2.1.4	INTEGER	read-write	The respective PTP Port of the Boundary Clock can be set to true (enabled) or set to false (disabled). If the port is disabled no PTP packets will be processed for the respective port.
hmNetPTPPortEntry	1.3.6.1.4.1.248.14.2.3.40.2.1		not-accessible	Entry for one port.
I32 hmNetPTPPortID	1.3.6.1.4.1.248.14.2.3.40.2.1.1	Integer32	read-only	Index to identify a port of the switch unit. This value is never greater than hmSysGroupCapacity.
INT hmNetPTPPortState	1.3.6.1.4.1.248.14.2.3.40.2.1.2	INTEGER	read-only	State of the PTP port intance.
hmNetPTPPortTable	1.3.6.1.4.1.248.14.2.3.40.2		not-accessible	This table contains variables for each PTP port of the switch.
INT hmNetPTPPreferredMaster	1.3.6.1.4.1.248.14.2.3.40.1.11	INTEGER	read-write	A clock may be administratively designated as part of a preferred master clock set. This creates a set of clocks that will be favored over those not so designated in the selection of master clocks within a subdomain. The purpose of this designation is to allow users to specify a clock that will remain master in the presence of disconnection or connection of other clocks.
I32 hmNetPTPSlavePort	1.3.6.1.4.1.248.14.2.3.40.1.4	Integer32	read-write	This members value shall indicate the slave port where this clock is synchronized in the ptp-mode-static-boundary-clock mode. The default value is 0 (i.e. clock is grandmaster).
I32 hmNetPTPStaticDrift	1.3.6.1.4.1.248.14.2.3.40.1.27	Integer32	read-write	Relative rate (frequency or drift) between a reference clock and this node in nanoseconds per second (ns/s). This value is only applied if no port is in slave state.
I32 hmNetPTPStepsRemoved	1.3.6.1.4.1.248.14.2.3.40.1.25	Integer32	read-only	This members value shall be the number of communication paths traversed between the local clock and the grandmaster clock. For example, steps_removed in a slave clock on the same PTP communication path as the grandmaster clock will have a value of 1, indicating that a single path was traversed.
OCT hmNetPTPSubdomainName	1.3.6.1.4.1.248.14.2.3.40.1.13	OCTET STRING	read-write	Each subdomain shall be characterized by a name recognized by all PTP clocks in the subdomain as the basis for sending and receiving PTP communications. Changes are applied after the initialization with the init key init-with-nvm or afer reboot if the configuration was saved. The values of the octets for the subdomain name may be chosen from the set consisting of the values of the printable ASCII characters starting with hex value 0x21 (!) up to and including hex value 0x7E (~).
INT hmNetPTPSyncInterval	1.3.6.1.4.1.248.14.2.3.40.1.12	INTEGER	read-write	The sync interval shall be the interval in seconds between successive Sync messages issued by master clocks. It shall have the same value for all clocks in a subdomain. The value of sync interval is a compromise between the inherent stability of the clocks, the responsiveness of the clocks in a subdomain to change, and the communication load imposed by PTP. Allowed values are 1,2,8,16 and 64. Changes are applied after the initialization with the init key init-with-nvm or after reboot if the configuration was saved.
I32 hmNetPTPSyncLowerBound	1.3.6.1.4.1.248.14.2.3.40.1.6	Integer32	read-write	This object defines when the hmNetPTPIsSynchronized object is set to true. If the absolute value of the offset is smaller than hmNetPTPSyncLowerBound, the hmNetPTPIsSynchronized is set true. The value is interpreted as nanoseconds.
I32 hmNetPTPSyncUpperBound	1.3.6.1.4.1.248.14.2.3.40.1.7	Integer32	read-write	This object defines when the hmNetPTPIsSynchronized object is set to false. If the absolute value of the offset is bigger than hmNetPTPSyncUpperBound, the hmNetPTPIsSynchronized is set false. The value is interpreted as nanoseconds.
I32 hmNetPTPTimeSeconds	1.3.6.1.4.1.248.14.2.3.40.1.17	Integer32	read-only	This members value shall indicate PTP time in seconds since 1.1.1970.
INT hmNetSNMPAccessStatus	1.3.6.1.4.1.248.14.2.3.50.4	INTEGER	read-write	Enables/disables the SNMP protocol access on this device. If only read access is allowed set this object to readOnly(3).
hmNetSNMPGroup	1.3.6.1.4.1.248.14.2.3.50
I32 hmNetSNMPPortNumber	1.3.6.1.4.1.248.14.2.3.50.6	Integer32	read-write	The port number of the snmp server. To activate the port number the device has to be restarted.
INT hmNetSNMPRadiusAuthenticate	1.3.6.1.4.1.248.14.2.3.50.7	INTEGER	read-write	Enables/disables authentication of SNMPv3 users via RADIUS server
INT hmNetSNMPSynchronizeV1V3Status	1.3.6.1.4.1.248.14.2.3.50.5	INTEGER	read-write	Enables/disables the synchronization between the SNMPv1 community and the SNMPv3 password. If enabled the first read-write community in hmAuthCommTable is used for the SNMPv3 admin password. This is the same password that is used in the user- and webinterface. Further, if enabled the first read-only community in hmAuthCommTable is used for the SNMPv3 user password.
INT hmNetSNMPv1Status	1.3.6.1.4.1.248.14.2.3.50.1	INTEGER	read-write	Enables/disables the SNMP Version 1 protocol.
INT hmNetSNMPv2Status	1.3.6.1.4.1.248.14.2.3.50.2	INTEGER	read-write	Enables/disables the SNMP Version 2 protocol.
INT hmNetSNMPv3EncryptionReadOnlyStatus	1.3.6.1.4.1.248.14.2.3.50.9	INTEGER	read-write	Enables/disables the SNMPv3 user Data Encryption.
INT hmNetSNMPv3EncryptionReadWriteStatus	1.3.6.1.4.1.248.14.2.3.50.8	INTEGER	read-write	Enables/disables the SNMPv3 admin Data Encryption.
INT hmNetSNMPv3Status	1.3.6.1.4.1.248.14.2.3.50.3	INTEGER	read-write	Enables/disables the SNMP Version 3 protocol.
INT hmNetSNTPAcceptBroadcasts	1.3.6.1.4.1.248.14.2.3.30.7	INTEGER	read-write	This MIB variable specifies whether SNTP broadcasts will be allowed to synchronize the local clock. If hmNetSNTPStatus is enabled, this variable will be ignored and broadcasts will not set the local clock.
IP hmNetSNTPAnycastAddr	1.3.6.1.4.1.248.14.2.3.30.8	IpAddress	read-write	Destination address for SNTP broadcasts. A broadcast, multicast or unicast address may be specified. Setting the address to 0.0.0.0 disables SNTP broadcasts.
I32 hmNetSNTPAnycastInterval	1.3.6.1.4.1.248.14.2.3.30.10	Integer32	read-write	Interval of SNTP broadcast messages in seconds.
I32 hmNetSNTPAnycastVlan	1.3.6.1.4.1.248.14.2.3.30.9	Integer32	read-write	Vlan for anycast mode.
INT hmNetSNTPClientStatus	1.3.6.1.4.1.248.14.2.3.30.16	INTEGER	read-write	Enables/disables the SNTP client on this device if hmNetSNTPStatus is enabled.
hmNetSNTPGroup	1.3.6.1.4.1.248.14.2.3.30
I32 hmNetSNTPLocalOffset	1.3.6.1.4.1.248.14.2.3.30.4	Integer32	read-write	The difference between local time and UTC in minutes.
INT hmNetSNTPOnceAtStartup	1.3.6.1.4.1.248.14.2.3.30.13	INTEGER	read-write	If enabled, SNTP ist automaticaly disabled after once synchronized to an SNTP Server.
I32 hmNetSNTPOperStatus	1.3.6.1.4.1.248.14.2.3.30.11	Integer32	read-only	Operational status of the SNTP sub-system. The value is a bit mask: 1 local system clock synchronized 2 SNTP loop detected 4 generic error 8 once synced, client disabled 100 server 1 not synchronized 200 server 1 bad protocol version 400 server 1 not responding 10000 server 2 not synchronized 20000 server 2 bad protocol version 40000 server 2 not responding (Note that all values are hexadecimal.)
IP hmNetSNTPServer	1.3.6.1.4.1.248.14.2.3.30.2	IpAddress	read-write	The IP Address of an external Time Server.
IP hmNetSNTPServer2	1.3.6.1.4.1.248.14.2.3.30.5	IpAddress	read-write	IP address of a secondary (backup) time server.
INT hmNetSNTPServerOnlyIfSync	1.3.6.1.4.1.248.14.2.3.30.14	INTEGER	read-write	The SNTP server is enabled only if synchronized to another external time reference. (e.g. SNTP or PTP)
INT hmNetSNTPServerStatus	1.3.6.1.4.1.248.14.2.3.30.15	INTEGER	read-write	Enables/disables the SNTP server on this device if hmNetSNTPStatus is enabled.
INT hmNetSNTPStatus	1.3.6.1.4.1.248.14.2.3.30.1	INTEGER	read-write	Enables/disables the Simple Network Time Protocol on this device.
I32 hmNetSNTPSyncInterval	1.3.6.1.4.1.248.14.2.3.30.6	Integer32	read-write	SNTP synchronisation interval in seconds.
TIK hmNetSNTPTime	1.3.6.1.4.1.248.14.2.3.30.3	TimeTicks	read-write	The time in seconds since 01/01/1900 UTC.
I32 hmNetSNTPTimeAdjustThreshold	1.3.6.1.4.1.248.14.2.3.30.12	Integer32	read-write	The threshold in milli-seconds whether to decide to set the received SNTP time directly to the local clock or not. If the hmNetSNTPTimeAdjustThreshold value is 0, the received SNTP time will be set directly to the local clock every time a SNTP message is received. If the difference between the local clock time and the received SNTP time is fewer than the hmNetSNTPTimeAdjustThreshold value, the local clock will not be set. If the difference between the local clock time and the received SNTP time is equal or larger than the hmNetSNTPTimeAdjustThreshold value, the local clock will be set.
I32 hmNetVlanID	1.3.6.1.4.1.248.14.2.3.8	Integer32	read-write	Vlan ID of the IP protocol stack. If the value is 0, Traffic from all Vlans is accepted. Every other value means that only traffic of the appropriate Vlan is accepted and outgoing traffic uses this Vlan ID.
I32 hmNetVlanPriority	1.3.6.1.4.1.248.14.2.3.10	Integer32	read-write	Vlan Priority which is used in management replies.
hmNetwork	1.3.6.1.4.1.248.14.2.3
I32 hmNetworkCpuIfAverageUtilization	1.3.6.1.4.1.248.14.2.15.4.2	Integer32	read-only	The average network utilization of the internal cpu interface in percent, measured over the last 30 minutes.
I32 hmNetworkCpuIfUtilization	1.3.6.1.4.1.248.14.2.15.4.1	Integer32	read-only	The current network utilization of the internal cpu interface in percent.
hmNetworkResources	1.3.6.1.4.1.248.14.2.15.4
NTF hmNTPTrap	1.3.6.1.4.1.248.14.2.0.12			This trap reports NTP error conditions. For a list of possible error conditions refer to hmNetNTPStatusCode.
hmPlugAndPlay	1.3.6.1.4.1.248.14.1.11.4
INT hmPNIOAdminStatus	1.3.6.1.4.1.248.14.2.16.1.1	INTEGER	read-write	Enables/disables the ProfinetIO functionality on this device. If disabled(2), the ProfinetIO protocol is inactive, but the ProfinetIO MIBs can be accessed. The default value is disabled.
INT hmPNIODcpMode	1.3.6.1.4.1.248.14.2.16.1.10.1.2	INTEGER	read-write	DCP mode for one port. Allowed values none(0), ingress(1), egress(2) or both(3) which is default.
hmPNIODcpModeEntry	1.3.6.1.4.1.248.14.2.16.1.10.1		not-accessible	DCP mode entry
INT hmPNIODcpModePortID	1.3.6.1.4.1.248.14.2.16.1.10.1.1	INTEGER	read-only	Port ID for the DCP mode table entry
hmPNIODcpModeTable	1.3.6.1.4.1.248.14.2.16.1.10		not-accessible	Table of DCP mode entries
I32 hmPNIODeviceID	1.3.6.1.4.1.248.14.2.16.1.2	Integer32	read-only	Identifier of the device family. Values 1 .. 65635 are valid device IDs.
STR hmPNIODeviceTypeDetails	1.3.6.1.4.1.248.14.2.16.1.5	DisplayString	read-only	Switch device type details, for example: 4 Port Rail Switch.
I32 hmPNIOHardwareRelease	1.3.6.1.4.1.248.14.2.16.1.7	Integer32	read-only	Version number of switch hardware in profinetio format.
I32 hmPNIOModuleIdentNumber	1.3.6.1.4.1.248.14.2.16.1.3	Integer32	read-only	Identifier ID of the device of port or module.
STR hmPNIONameOfStation	1.3.6.1.4.1.248.14.2.16.1.11	DisplayString	read-write	Device name. The size is restricted to 240 characters. It must be conform to the restrictions as decribed in PNIO protocol specification.
STR hmPNIOOrderID	1.3.6.1.4.1.248.14.2.16.1.4	DisplayString	read-only	Product (switch) order ID. The size is restricted to 64 characters.
STR hmPNIOOrderID9th	1.3.6.1.4.1.248.14.2.16.1.8	DisplayString	read-only	Product (switch) order ID. The size is restricted to 32 characters (In the form of the 9-th numbers).
STR hmPNIOSoftwareRelease	1.3.6.1.4.1.248.14.2.16.1.6	DisplayString	read-only	This value is a string that contains Version number of software in profinetio format, for example: 01.0.03.
INT hmPOEFastStartup	1.3.6.1.4.1.248.14.2.14.1.4	INTEGER	read-write	Enables/disables Power over Ethernet on this device. The default value is enable.
hmPOEGlobalGroup	1.3.6.1.4.1.248.14.2.14.1
hmPOEGroup	1.3.6.1.4.1.248.14.2.14
I32 hmPOEModuleDeliveredPower	1.3.6.1.4.1.248.14.2.14.3.1.5	Integer32	read-only	The measured usage power per module expressed in Watts.
hmPOEModuleEntry	1.3.6.1.4.1.248.14.2.14.3.1		not-accessible	The entries of the hmPOEModuleTable.
I32 hmPOEModuleIndex	1.3.6.1.4.1.248.14.2.14.3.1.1	Integer32	read-only	Slot number of the plugged PoE+ module.
I32 hmPOEModuleMaximumPower	1.3.6.1.4.1.248.14.2.14.3.1.3	Integer32	read-only	Maximum available power budget per module expressed in Watts. This value depends on the device or module.
T/F hmPOEModuleNotificationControlEnable	1.3.6.1.4.1.248.14.2.14.3.1.7	TruthValue	read-write	This object controls, on a per-module basis, whether or not notifications from the agent are enabled.
I32 hmPOEModulePower	1.3.6.1.4.1.248.14.2.14.3.1.2	Integer32	read-write	Configurable power budget per module expressed in Watts. The default value is hmPOEModuleMaximumPower and depends on the hardware.
NTF hmPOEModulePowerUsageOffNotification	1.3.6.1.4.1.248.14.2.0.15			This trap reports POE error condition. This Notification indicate PSE Threshold usage indication is on, the usage power is below the threshold. At least 500 msec must elapse between notifications being emitted by the same object instance.
NTF hmPOEModulePowerUsageOnNotification	1.3.6.1.4.1.248.14.2.0.14			This trap reports POE error condition. This Notification indicate PSE Threshold usage indication is on, the usage power is above the threshold. At least 500 msec must elapse between notifications being emitted by the same object instance.
I32 hmPOEModuleReservedPower	1.3.6.1.4.1.248.14.2.14.3.1.4	Integer32	read-only	The reserved power (depending on actual power classes) per module expressed in Watts.
hmPOEModuleTable	1.3.6.1.4.1.248.14.2.14.3		not-accessible	This table contains objects for each plugged PoE+ module of the switch. If the device is non-modular and supports PoE+ it contains only one entry.
I32 hmPOEModuleUsageThreshold	1.3.6.1.4.1.248.14.2.14.3.1.6	Integer32	read-write	The usage power threshold per module expressed in percent. If this threshold is exceeded a alarm is initiated.
I32 hmPOEPortConsumptionPower	1.3.6.1.4.1.248.14.2.14.2.1.2	Integer32	read-only	Measured usage power per interface expressed in Milliwatts.
hmPOEPortEntry	1.3.6.1.4.1.248.14.2.14.2.1		not-accessible	The entry of the hmPOEPortTable.
I32 hmPOEPortIndex	1.3.6.1.4.1.248.14.2.14.2.1.1	Integer32	read-only	Index to identify an Power over Ethernet interface.
hmPOEPortTable	1.3.6.1.4.1.248.14.2.14.2		not-accessible	This table contains variables for each Power over Ethernet interface of the switch.
I32 hmPOEReservedPower	1.3.6.1.4.1.248.14.2.14.1.3	Integer32	read-only	Reserved system power for active Power over Ethernet ports in Watts.
INT hmPOEScanning	1.3.6.1.4.1.248.14.2.14.1.2	INTEGER	read-write	Enables/disables port scanning on this device. The default value is enable.
INT hmPOEStatus	1.3.6.1.4.1.248.14.2.14.1.1	INTEGER	read-write	Enables/disables Power over Ethernet on this device. The default value is enable.
T/F hmPortMonitorAdminMode	1.3.6.1.4.1.248.14.2.18.1	TruthValue	read-write	Global switch to enable / disable the port state actions, which are performed if a condition becomes true
I32 hmPortMonitorConditionCrcFragmentsCount	1.3.6.1.4.1.248.14.2.18.3.3.2	Integer32	read-write	CrcFragments counter (1-1000000).
I32 hmPortMonitorConditionCrcFragmentsCountInterval	1.3.6.1.4.1.248.14.2.18.3.3.3.1.1	Integer32	read-only	CrcFragments count that occured in last interval.
I32 hmPortMonitorConditionCrcFragmentsCountTotal	1.3.6.1.4.1.248.14.2.18.3.3.3.1.2	Integer32	read-only	Total CrcFragments count.
hmPortMonitorConditionCrcFragmentsGroup	1.3.6.1.4.1.248.14.2.18.3.3
I32 hmPortMonitorConditionCrcFragmentsInterval	1.3.6.1.4.1.248.14.2.18.3.3.1	Integer32	read-write	Measure interval in seconds (5-180s) for CrcFragments detection.
hmPortMonitorConditionCrcFragmentsIntfEntry	1.3.6.1.4.1.248.14.2.18.3.3.3.1		not-accessible	Port condition CrcFragments interface entry.
hmPortMonitorConditionCrcFragmentsIntfTable	1.3.6.1.4.1.248.14.2.18.3.3.3		not-accessible	Port condition CrcFragments interface table.
T/F hmPortMonitorConditionCrcFragmentsMode	1.3.6.1.4.1.248.14.2.18.3.1.1.2	TruthValue	read-write	Interface CrcFragments mode.
BIT hmPortMonitorConditionField	1.3.6.1.4.1.248.14.2.18.3.1.1.3	Bits	read-only	Condition type field.
hmPortMonitorConditionGroup	1.3.6.1.4.1.248.14.2.18.3
hmPortMonitorConditionIntfEntry	1.3.6.1.4.1.248.14.2.18.3.1.1		not-accessible	Port state action interface entry.
I32 hmPortMonitorConditionLinkFlapCount	1.3.6.1.4.1.248.14.2.18.3.2.2	Integer32	read-write	Link flap counter (1-100).
I32 hmPortMonitorConditionLinkFlapCountInterval	1.3.6.1.4.1.248.14.2.18.3.2.3.1.1	Integer32	read-only	Link flap count that occured in last interval.
I32 hmPortMonitorConditionLinkFlapCountTotal	1.3.6.1.4.1.248.14.2.18.3.2.3.1.2	Integer32	read-only	Total link flap count.
hmPortMonitorConditionLinkFlapGroup	1.3.6.1.4.1.248.14.2.18.3.2
I32 hmPortMonitorConditionLinkFlapInterval	1.3.6.1.4.1.248.14.2.18.3.2.1	Integer32	read-write	Measure interval in seconds (1-180s) for link flap detection.
hmPortMonitorConditionLinkFlapIntfEntry	1.3.6.1.4.1.248.14.2.18.3.2.3.1		not-accessible	Port condition link flap interface entry.
hmPortMonitorConditionLinkFlapIntfTable	1.3.6.1.4.1.248.14.2.18.3.2.3		not-accessible	Port condition link flap interface table.
T/F hmPortMonitorConditionLinkFlapMode	1.3.6.1.4.1.248.14.2.18.3.1.1.1	TruthValue	read-write	Interface link flap mode.
hmPortMonitorConditionTable	1.3.6.1.4.1.248.14.2.18.3.1		not-accessible	Port state condition interface table.
hmPortMonitorGroup	1.3.6.1.4.1.248.14.2.18
INT hmPortMonitorIntfAction	1.3.6.1.4.1.248.14.2.18.2.1.3	INTEGER	read-write	Interface link disable state.
hmPortMonitorIntfEntry	1.3.6.1.4.1.248.14.2.18.2.1		not-accessible	Port state mode interface entry.
T/F hmPortMonitorIntfMode	1.3.6.1.4.1.248.14.2.18.2.1.1	TruthValue	read-write	Port monitor interface mode.
T/F hmPortMonitorIntfReset	1.3.6.1.4.1.248.14.2.18.2.1.2	TruthValue	read-write	Port monitor interface reset.
hmPortMonitorIntfTable	1.3.6.1.4.1.248.14.2.18.2		not-accessible	Port state mode interface table.
NTF hmPortMonitorPortDisabledTrap	1.3.6.1.4.1.248.14.2.0.13			This trap is sent if a port has been disabled by port disable action by port monitor.
NTF hmPowerSupply	1.3.6.1.4.1.248.14.1.0.2			This trap is sent if the state of a power supply unit changes.
MAC hmPrioMACAddress	1.3.6.1.4.1.248.14.1.4.10.1.1	MacAddress	read-only	same as dot1dStaticAddress
INT hmPrioMACAddressEnable	1.3.6.1.4.1.248.14.1.4.2	INTEGER	read-write	Global configuration of feature priority by MAC address. If enabled, for each static MAC address a priority could be specified
hmPrioMACAddressEntry	1.3.6.1.4.1.248.14.1.4.10.1		not-accessible	The entry of the hmPrioMACAddressTable.
hmPrioMACAddressTable	1.3.6.1.4.1.248.14.1.4.10		not-accessible	Table for assigning priority to MAC addresses
I32 hmPrioMACPriority	1.3.6.1.4.1.248.14.1.4.10.1.3	Integer32	read-write	priority value for the frame with the specific destination MAC address. 0..7: priority 8 : disabled (no priority by MAC address) 9 : discard the frame
I32 hmPrioMACReceivePort	1.3.6.1.4.1.248.14.1.4.10.1.2	Integer32	read-only	to be compatible with dot1dStaticTable
INT hmPrioMACStatus	1.3.6.1.4.1.248.14.1.4.10.1.4	INTEGER	read-write	status flag according to dot1dStaticStatus
INT hmPrioTOSEnable	1.3.6.1.4.1.248.14.1.4.1	INTEGER	read-write	Global configuration of feature IP-TOS priority to 802.1D-1998 priority. If enabled, the priority of the TOS field is mapped to 802.1D priority
hmPrioTosToPrioEntry	1.3.6.1.4.1.248.14.1.4.12.1		not-accessible	The entry of the hmPrioTosToPrioEntry.
hmPrioTosToPrioTable	1.3.6.1.4.1.248.14.1.4.12		not-accessible	Translation table IP-TOS priority to 802.1D-1998 priority
hmPrioTrafficClassEntry	1.3.6.1.4.1.248.14.1.4.11.1		not-accessible	The entry of the hmPrioTrafficClassTable.
I32 hmPrioTrafficClassID	1.3.6.1.4.1.248.14.1.4.11.1.1	Integer32	read-only	This index is used to identify the associated traffic class
hmPrioTrafficClassTable	1.3.6.1.4.1.248.14.1.4.11		not-accessible	Translation table for traffic classes to 802.1D-1998 priority
I32 hmPrioTrafficClassWeight	1.3.6.1.4.1.248.14.1.4.11.1.2	Integer32	read-write	With this parameter the queue mode of each traffic class can be set. 2..99: weight for WFQ (Weighted-Fair-Queuing) 100: strict priority
I32 hmPrioTTPPrio	1.3.6.1.4.1.248.14.1.4.12.1.2	Integer32	read-only	This index is used to identify the associated 802.1D priority
I32 hmPrioTTPTos	1.3.6.1.4.1.248.14.1.4.12.1.1	Integer32	read-only	This index is used to identify the associated TOS value
INT hmPrioVlan0TagTransparentMode	1.3.6.1.4.1.248.14.1.4.3	INTEGER	read-write	enables or disables the transparent mode for priority tagged frames (frames with VLAN-ID 0) for the switch unit.
hmProducts	1.3.6.1.4.1.248.14.10
hmProfinetIOConfigGroup	1.3.6.1.4.1.248.14.2.16.1
hmProfinetIOStatisticsGroup	1.3.6.1.4.1.248.14.2.16.2
STR hmPSDescription	1.3.6.1.4.1.248.14.1.2.1.6	DisplayString	read-only	Description of the associated power supply.
hmPSEntry	1.3.6.1.4.1.248.14.1.2.1		not-accessible	The entry of the hmPSTable.
I32 hmPSID	1.3.6.1.4.1.248.14.1.2.1.2	Integer32	read-only	This Index is used to identify the associated power supply unit.
I32 hmPSPowerBudget	1.3.6.1.4.1.248.14.1.2.1.9	Integer32	read-only	Power budget of the associated power supply.
STR hmPSProductCode	1.3.6.1.4.1.248.14.1.2.1.8	DisplayString	read-only	Product code of the associated power supply.
STR hmPSSerialNumber	1.3.6.1.4.1.248.14.1.2.1.7	DisplayString	read-only	Serial number of the associated power supply.
INT hmPSState	1.3.6.1.4.1.248.14.1.2.1.3	INTEGER	read-only	Indicates the operational state of the associated power supply. If the value of this variable changes, a hmPowerSupply trap is sent.
I32 hmPSSysID	1.3.6.1.4.1.248.14.1.2.1.1	Integer32	read-only	The value of SysID is assigned so as to uniquely identify a chassis/switch among the subordinate managed objects of the system.
hmPSTable	1.3.6.1.4.1.248.14.1.2		not-accessible	This table contains all variables related to the power supply units of the chassis/switch. For each power supply slot exists one instance.
INT hmPSType	1.3.6.1.4.1.248.14.1.2.1.4	INTEGER	read-only	Type of the associated power supply.
I32 hmPSVersion	1.3.6.1.4.1.248.14.1.2.1.5	Integer32	read-only	Version of the associated power supply.
C32 hmRelayBCPktInCnt	1.3.6.1.4.1.248.14.2.11.20	Counter32	read-only	The number of BOOTP/DHCP broadcast request packets received by the relay agent.
IP hmRelayDHCPServer2IpAddr	1.3.6.1.4.1.248.14.2.11.10.2	IpAddress	read-write	The IP address of the second DHCP-server to be addressed by the relay agent. If 0.0.0.0, DHCP relaying is switched off for this entry.
IP hmRelayDHCPServer3IpAddr	1.3.6.1.4.1.248.14.2.11.10.3	IpAddress	read-write	The IP address of the third DHCP-server to be addressed by the relay agent. If 0.0.0.0, DHCP relaying is switched off for this entry.
IP hmRelayDHCPServer4IpAddr	1.3.6.1.4.1.248.14.2.11.10.4	IpAddress	read-write	The IP address of the fourth DHCP-server to be addressed by the relay agent. If 0.0.0.0, DHCP relaying is switched off for this entry.
IP hmRelayDHCPServerIpAddr	1.3.6.1.4.1.248.14.2.11.10.1	IpAddress	read-write	The IP address of the first DHCP-server to be addressed by the relay agent. If 0.0.0.0, DHCP relaying is switched off for this entry.
NTF hmRelayDuplicateIPTrap	1.3.6.1.4.1.248.14.2.0.5			This trap reports the detection of a duplicate ip address by the relay agent.
C32 hmRelayErrCnt	1.3.6.1.4.1.248.14.2.11.24	Counter32	read-only	The number of errors encountered within the relay agent.
hmRelayGroup	1.3.6.1.4.1.248.14.2.11
INT hmRelayIfaceBCRequestFwd	1.3.6.1.4.1.248.14.2.11.11.1.4	INTEGER	read-write	Enable or disable relaying of incoming broadcasted BOOTP/DHCP request packets on this physical port. Hirschmann Multicast BOOTP/DHCP requests will always be relayed.
OCT hmRelayIfaceCircuitID	1.3.6.1.4.1.248.14.2.11.11.1.5	OCTET STRING	read-only	Contains the actual Circuit ID sub option for this interface of the relay agent. It is a best guess value, since some information is not known before the actual reception of a BOOTP/DHCP request message.
I32 hmRelayIfaceGroupID	1.3.6.1.4.1.248.14.2.11.11.1.1	Integer32	read-only	index to identify an interface card. This value is never greater than hmSysGroupCapacity.
I32 hmRelayIfaceID	1.3.6.1.4.1.248.14.2.11.11.1.2	Integer32	read-only	index to identify an interface within an interface card.
INT hmRelayIfaceOption82Enable	1.3.6.1.4.1.248.14.2.11.11.1.3	INTEGER	read-write	Enable or disable DHCP Option 82 on this physical port.
hmRelayInterfaceEntry	1.3.6.1.4.1.248.14.2.11.11.1		not-accessible	The entry of the hmRelayInterfaceTable.
hmRelayInterfaceTable	1.3.6.1.4.1.248.14.2.11.11		not-accessible	This table contains variables for each interface of the switch.
IP hmRelayLastDuplicateIP	1.3.6.1.4.1.248.14.2.11.25	IpAddress	read-only	The last duplicate ip address encounterd by the relay agent.
C32 hmRelayMCPktInCnt	1.3.6.1.4.1.248.14.2.11.21	Counter32	read-only	The number of BOOTP/DHCP multicast request packets received by the relay agent.
INT hmRelayOption82Status	1.3.6.1.4.1.248.14.2.11.1	INTEGER	read-write	Enables/disables the DHCP Option 82 defined in RFC 3046 on this device.
OCT hmRelayOptionRemoteID	1.3.6.1.4.1.248.14.2.11.3	OCTET STRING	read-only	Displays the actual content of the Remote ID sub option for this relay agent. The value is encoded in TLV (Type-Length-Value) format. The following type values are currently defined: 00 = mac adress A1 = ip address A2 = client identifier A3 = string in hmRelayOptionRemoteIDValue
INT hmRelayOptionRemoteIDType	1.3.6.1.4.1.248.14.2.11.2	INTEGER	read-write	This option determines the content of the Agent Remote ID (sub-option 2). ip(1) inserts the ip address of the relay's mgmt-interface and encodes it with sub option type A1. mac(2) inserts the mac adress of the relay's mgmt-interface and encodes it with sub option type 00. client-id(3) inserts the client identifier (sysName) of the relay's mgmt-interface and encodes it with sub option type A2. other(4) inserts the value in hmRelayOptionRemoteIDValue and encodes it with sub option type A3.
OCT hmRelayOptionRemoteIDValue	1.3.6.1.4.1.248.14.2.11.4	OCTET STRING	read-write	Contains an octet string to be used as value for Agent Remote ID Sub-option type A3
C32 hmRelayPktClientRelayCnt	1.3.6.1.4.1.248.14.2.11.23	Counter32	read-only	The number of BOOTP/DHCP replies relayed to the Client.
C32 hmRelayPktServerRelayCnt	1.3.6.1.4.1.248.14.2.11.22	Counter32	read-only	The number of BOOTP/DHCP requests relayed to the DHCP Server.
hmRelayServerGroup	1.3.6.1.4.1.248.14.2.11.10
hmRestrictedMgtAccessGroup	1.3.6.1.4.1.248.14.2.3.70
hmRMAEntry	1.3.6.1.4.1.248.14.2.3.70.2.1		not-accessible	An entry contains a rule for the Management Access.
INT hmRMAIndex	1.3.6.1.4.1.248.14.2.3.70.2.1.1	INTEGER	read-only	The unique index used for each row in the RMA Table
IP hmRMAIpAddr	1.3.6.1.4.1.248.14.2.3.70.2.1.3	IpAddress	read-write	Allowed IP address
IP hmRMANetMask	1.3.6.1.4.1.248.14.2.3.70.2.1.4	IpAddress	read-write	Network Mask
INT hmRMAOperation	1.3.6.1.4.1.248.14.2.3.70.1	INTEGER	read-write	Enables/disables Management Access globally
ROW hmRMARowStatus	1.3.6.1.4.1.248.14.2.3.70.2.1.2	RowStatus	read-create	Describes the status of a row in this table if it is active or not available ...
INT hmRMASrvHttp	1.3.6.1.4.1.248.14.2.3.70.2.1.5	INTEGER	read-write	Enables/disables HHTP access
INT hmRMASrvSnmp	1.3.6.1.4.1.248.14.2.3.70.2.1.6	INTEGER	read-write	Enables/disbales SNMP access
INT hmRMASrvSsh	1.3.6.1.4.1.248.14.2.3.70.2.1.8	INTEGER	read-write	Enables/disables SSH access
INT hmRMASrvTelnet	1.3.6.1.4.1.248.14.2.3.70.2.1.7	INTEGER	read-write	Enables/disables Telnet access
hmRMATable	1.3.6.1.4.1.248.14.2.3.70.2		not-accessible	A list of Management Access Entries (Rules) to increase security
INT hmRS2ConfigError	1.3.6.1.4.1.248.14.1.10.2	INTEGER	read-only	RS2hmConfigError indicates a configuration error of the system: no error: no configuration error, error: in normal mode hmConfigError indicates failure of control line or connection of 2 RS2 in normal mode, in stand by mode hmConfigError indicates absence of control line, failure of control line or connection of 2 RS2 in stand by mode.
hmRS2ConnectionMirroringGroup	1.3.6.1.4.1.248.14.1.10.8
I32 hmRS2ConnectionMirroringPortOne	1.3.6.1.4.1.248.14.1.10.8.2	Integer32	read-write	Set this variable to the first port to be mirrored.
I32 hmRS2ConnectionMirroringPortTwo	1.3.6.1.4.1.248.14.1.10.8.3	Integer32	read-write	Set this variable to the second port to be mirrored.
INT hmRS2ConnectionMirroringStatus	1.3.6.1.4.1.248.14.1.10.8.1	INTEGER	read-write	Set this variable to configure the status of the connection mirroring functionality. The definition of a destination port is not required.
hmRS2DisableLearningGroup	1.3.6.1.4.1.248.14.1.10.9
INT hmRS2DisableLearningStatus	1.3.6.1.4.1.248.14.1.10.9.1	INTEGER	read-write	When set to active the Learning Process is disabled, no new Dynamic Filtering Entries are created and exsisting Dynamic Filtering Entries are removed from the Filtering Database. Static Filtering Entries and Group Registration Entries are not affected.
hmRS2ext	1.3.6.1.4.1.248.14.1.10
hmRS2FDBGroup	1.3.6.1.4.1.248.14.1.10.16
hmRS2FDBHashGroup	1.3.6.1.4.1.248.14.1.10.16.1
INT hmRS2FDBHashOptimizingMode	1.3.6.1.4.1.248.14.1.10.16.1.1	INTEGER	read-write	Enables/disables the hash optimizing mode on this device. When enabled the switch will use another hash algorithm optimized for incrementing addresses. After setting this variable the switch have to be reset. The default value is disable.
INT hmRS2FDBHashOptimizingStatus	1.3.6.1.4.1.248.14.1.10.16.1.2	INTEGER	read-only	Shows the current hash mode of this device. When enabled the switch uses the optimized hash mode, else the normal mode.
INT hmRS2OperMode	1.3.6.1.4.1.248.14.1.10.1	INTEGER	read-only	hmRS2OperMode shows the operational mode of the system: normal: normal mode, standby-active: standby mode, but switch is active, because the master switch is e.g. not reachable, standby-inactive: stand by mode, redundancy-manager-active: redundancy mode and redundancy-manager has closed RS2 ring, redundancy-manager-inactive: redundancy mode and redundancy-manager has opened RS2 ring. If the value changes, a trap is sent.
IP hmRS2PartnerIpAddress	1.3.6.1.4.1.248.14.1.10.7.1	IpAddress	read-write	This variable can be used to set manually the redundancy partner of the RS2 agent.
INT hmRS2PSAlarm	1.3.6.1.4.1.248.14.1.10.13.1	INTEGER	read-write	Enables/disables an alarm for the signalling relay of the powersupply state.
hmRS2PSGroup	1.3.6.1.4.1.248.14.1.10.13
INT hmRS2RedNotGuaranteedAlarm	1.3.6.1.4.1.248.14.1.10.14.1	INTEGER	read-write	When enabled the message 'redundancy not guaranteed' will be signalled on the signalling relay.
hmRS2RedundancyGroup	1.3.6.1.4.1.248.14.1.10.14
hmRS2SelftestGroup	1.3.6.1.4.1.248.14.1.10.12
I32 hmRS2SelftestMode	1.3.6.1.4.1.248.14.1.10.12.2	Integer32	read-write	Mode of the selftest coded as an integer value with each bit representing a special behaviour of the tests. Meaning of the bits: Bit 0: reboot on failure Bit 1: show failure with hmRS2SigRelayState (a trap will be send also) Bit 2: do switch memory test on start up Bit 3: Clear Bit 2 after next reboot if test has been successfully completed
I32 hmRS2SelftestResult	1.3.6.1.4.1.248.14.1.10.12.1	Integer32	read-only	Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: error switch memory
hmRS2SigRelayGroup	1.3.6.1.4.1.248.14.1.10.10
INT hmRS2SigRelayManualState	1.3.6.1.4.1.248.14.1.10.10.2	INTEGER	read-write	When set to on, this is the default, the signalling relay is opened. When set to off the relay is closed.
INT hmRS2SigRelayMode	1.3.6.1.4.1.248.14.1.10.10.1	INTEGER	read-write	When set to standard, this is the default, the signalling relay shows the state of hmRS2SigRelayState. When set to manual, the relay is controlled by hmRS2SigRelayManualState.
INT hmRS2SigRelayState	1.3.6.1.4.1.248.14.1.10.3	INTEGER	read-only	hmRS2SigRelayState shows the state of the (non potential) signalling relay in standard mode: off: ok, on: powersupply not ok or linkstate of a port not ok or configuration error, see power supply table or ifMauTable (attribute ifMauMediaAvailable) or hmConfigError for details.
hmRS2TopologyEntry	1.3.6.1.4.1.248.14.1.10.7.2.1		not-accessible	The entry of the hmRS2TopologyTable.
hmRS2TopologyGroup	1.3.6.1.4.1.248.14.1.10.7
IP hmRS2TopologyIpAddress	1.3.6.1.4.1.248.14.1.10.7.2.1.2	IpAddress	read-write	This variable can be used to set manually the next RS2 agent.
I32 hmRS2TopologyLinkID	1.3.6.1.4.1.248.14.1.10.7.2.1.1	Integer32	read-only	This index is used to identify the associated link and corresponds with ifMauIfIndex.
hmRS2TopologyTable	1.3.6.1.4.1.248.14.1.10.7.2		not-accessible	This table describes the topology of rs2-rings.
hmRS2VlanGroup	1.3.6.1.4.1.248.14.1.10.11
INT hmRS2VlanMode	1.3.6.1.4.1.248.14.1.10.11.1	INTEGER	read-write	Enables/disables the VLAN mode on this device. When enabled the switch will operate in 802.1Q mode, else in 802.1d mode. After setting this variable the switch have to be reset. The default value is disable.
INT hmRS2VlanStatus	1.3.6.1.4.1.248.14.1.10.11.2	INTEGER	read-only	Shows the current VLAN mode of this device. When enabled the switch operates in 802.1Q mode, else in 802.1d mode.
hmRS4RGroup	1.3.6.1.4.1.248.14.1.10.15
hmRS4RVlanGroup	1.3.6.1.4.1.248.14.1.10.15.1
hmRS4RVlanPortEntry	1.3.6.1.4.1.248.14.1.10.15.1.1.1		not-accessible	The entry of the hmRS4RVlanPortTable.
I32 hmRS4RVlanPortID	1.3.6.1.4.1.248.14.1.10.15.1.1.1.1	Integer32	not-accessible	This index is used to identify the port.
hmRS4RVlanPortTable	1.3.6.1.4.1.248.14.1.10.15.1.1		not-accessible	This table describes private vlan enhancements of rs2-4r devices.
INT hmRS4RVlanPortTagFormatRstp	1.3.6.1.4.1.248.14.1.10.15.1.1.1.2	INTEGER	read-write	When enabled all tags are removed when sending packets on the port (egress). When disabled tag format is not changed, but RSTP frames are sent tagged. This variable is only used if RSTP is enabled. The default value is enable.
I32 hmSelfTestBBResult	1.3.6.1.4.1.248.14.1.11.1.2	Integer32	read-only	Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of backplane port no 1 Bit 1: selftest error of backplane port no 2 Bit 2: selftest error of backplane port no 3 Bit 3: selftest error of backplane port no 4 Bit 8: selftest error of network processor no 1 Bit 9: selftest error of network processor no 2 Bit 10: selftest error of network processor no 3 Bit 11: selftest error of network processor no 4 Bit 12: selftest error of xpif no 1 Bit 13: selftest error of xpif no 2 Bit 14: selftest error of xpif no 3 Bit 15: selftest error of xpif no 4 Bit 16: error packet memory size Bit 30: error on board eeprom
I32 hmSelfTestBPResult	1.3.6.1.4.1.248.14.1.11.1.3	Integer32	read-only	Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: communication error with card 1 Bit 1: communication error with card 2 Bit 2: communication error with card 3 Bit 3: communication error with card 4 Bit 4: communication error with card 5 Bit 24: main and redundant eeprom 2 are different Bit 25: main and redundant eeprom 1 are different Bit 27: error on redundant eeprom 2 Bit 28: error on redundant eeprom 1 Bit 29: error on main eeprom 2 Bit 30: error on main eeprom 1
I32 hmSelfTestCpuResult	1.3.6.1.4.1.248.14.1.11.1.1	Integer32	read-only	Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits 0..15 set in the result indicate warning conditions, bits 16..31 indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: default configuration activated and running Bit 2: BB_DATAMEM_ERROR caused by log-entry: S_mmcssp_CRC_ERROR_DATAMEM ( in mmcNP5400Int() ) S_mmcssp_LEN_ERROR_DATAMEM ( in mmcNP5400Int() ) Bit 3: BB_PARITY_ERROR caused by log-entry: S_mmcssp_PER_ON_VIX_OR_IPC ( in mmcNP5400Int() ) S_mmcssp_PE_PIF_VIX_DATA ( in mmcEpifPintProc(), mmcGpifPintProc(), mmcXpifPintProc() ) S_mmcssp_PE_PIF_GGI ( in mmcGpifPintProc(), mmcXpifPintProc() ) Bit 4: BOOT_ERROR_PIF caused by log-entry: S_mmcssp_PIF_BOOT_ERROR ( in mmcEpifPintProc(), mmcGpifPintProc(), mmcXpifPintProc() ) Bit 5: MMC_PORT_PROBLEM caused by log-entry: S_mmcssp_WRONG_PORT_IN_MSG ( in mmcGotAliveMsg() ) S_mmcssp_NO_ADDRESS_FOR_PORT ( in mmcPortConfig() ) Bit 16: configuration data in bootblock of flash was invalid through startup Bit 17: configuration in flash is corrupted
NTF hmSelftestError	1.3.6.1.4.1.248.14.1.0.6			This trap is sent if the value of one of the selftest results is not zero or if a value changes while the agent is running.
I32 hmSelfTestM1Result	1.3.6.1.4.1.248.14.1.11.1.4	Integer32	read-only	Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of port no 1 Bit 1: selftest error of port no 2 Bit 2: selftest error of port no 3 Bit 3: selftest error of port no 4 Bit 4: selftest error of port no 5 Bit 5: selftest error of port no 6 Bit 6: selftest error of port no 7 Bit 7: selftest error of port no 8 Bit 16: selftest error of pif no 1 Bit 17: selftest error of pif no 2 Bit 30: error on module eeprom
I32 hmSelfTestM2Result	1.3.6.1.4.1.248.14.1.11.1.5	Integer32	read-only	Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of port no 1 Bit 1: selftest error of port no 2 Bit 2: selftest error of port no 3 Bit 3: selftest error of port no 4 Bit 4: selftest error of port no 5 Bit 5: selftest error of port no 6 Bit 6: selftest error of port no 7 Bit 7: selftest error of port no 8 Bit 16: selftest error of pif no 1 Bit 17: selftest error of pif no 2 Bit 30: error on module eeprom
I32 hmSelfTestM3Result	1.3.6.1.4.1.248.14.1.11.1.6	Integer32	read-only	Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of port no 1 Bit 1: selftest error of port no 2 Bit 2: selftest error of port no 3 Bit 3: selftest error of port no 4 Bit 4: selftest error of port no 5 Bit 5: selftest error of port no 6 Bit 6: selftest error of port no 7 Bit 7: selftest error of port no 8 Bit 16: selftest error of pif no 1 Bit 17: selftest error of pif no 2 Bit 30: error on module eeprom
I32 hmSelfTestM4Result	1.3.6.1.4.1.248.14.1.11.1.7	Integer32	read-only	Result of the selftest coded as an integer value with each bit representing the result of a different sub part test. Bits set in the result indicate error conditions of the sub part tests. Meaning of the bits: Bit 0: selftest error of port no 1 Bit 1: selftest error of port no 2 Bit 2: selftest error of port no 3 Bit 3: selftest error of port no 4 Bit 4: selftest error of port no 5 Bit 5: selftest error of port no 6 Bit 6: selftest error of port no 7 Bit 7: selftest error of port no 8 Bit 16: selftest error of pif no 1 Bit 17: selftest error of pif no 2 Bit 30: error on module eeprom
INT hmSelfTestMode	1.3.6.1.4.1.248.14.1.11.1.8	INTEGER	read-write	Setting this variable to enable(1) results in a full report of all detected selftest errors. The default value is disable(2).
hmSelfTestResults	1.3.6.1.4.1.248.14.1.11.1
STR hmSerialNumBB	1.3.6.1.4.1.248.14.1.11.3.2	DisplayString	read-only	Serial Number of the basic board.
hmSerialNumbers	1.3.6.1.4.1.248.14.1.11.3
STR hmSerialNumBP	1.3.6.1.4.1.248.14.1.11.3.3	DisplayString	read-only	Serial Number of the packplane unit.
STR hmSerialNumCpu	1.3.6.1.4.1.248.14.1.11.3.1	DisplayString	read-only	Serial Number of the CPU board.
STR hmSerialNumM1	1.3.6.1.4.1.248.14.1.11.3.4	DisplayString	read-only	Serial Number of module 1.
STR hmSerialNumM2	1.3.6.1.4.1.248.14.1.11.3.5	DisplayString	read-only	Serial Number of module 2.
STR hmSerialNumM3	1.3.6.1.4.1.248.14.1.11.3.6	DisplayString	read-only	Serial Number of module 3.
STR hmSerialNumM4	1.3.6.1.4.1.248.14.1.11.3.7	DisplayString	read-only	Serial Number of module 4.
I32 hmSfpBitRate	1.3.6.1.4.1.248.14.1.1.13.1.11	Integer32	read-only	The SFP's nominal bitrate in units of MBits/sec. Contains -1 in case of a device read error.
NTF hmSFPChangeTrap	1.3.6.1.4.1.248.14.1.0.11			This trap is sent when a SFP has been added or removed. It is also sent for an otherwise unsupported SFP.
INT hmSfpConnector	1.3.6.1.4.1.248.14.1.1.13.1.3	INTEGER	read-only	The SFP's Connector Type.
STR hmSfpDateCode	1.3.6.1.4.1.248.14.1.1.13.1.10	DisplayString	read-only	The SFP's vendor manufacturing date code. Format is YY:MM:DD.
hmSFPEntry	1.3.6.1.4.1.248.14.1.1.13.1		not-accessible	Entry for a detected SFP.
I32 hmSfpGroupID	1.3.6.1.4.1.248.14.1.1.13.1.1	Integer32	not-accessible	Index to identify a module. This value is never greater than hmSysGroupModuleCapacity.
I32 hmSfpID	1.3.6.1.4.1.248.14.1.1.13.1.2	Integer32	not-accessible	Index to identify an interface within a module. This value is never greater than hmSysModulePortCapacity.
I32 hmSfpInfoMagic	1.3.6.1.4.1.248.14.1.1.13.1.23	Integer32	read-only	1, if SFP contains vendor specific information by Hirschmann, otherwise 0.
STR hmSfpInfoPartId	1.3.6.1.4.1.248.14.1.1.13.1.22	DisplayString	read-only	Part Identifier of SFP's Hirschmann Information.
STR hmSfpInfoPartNumber	1.3.6.1.4.1.248.14.1.1.13.1.21	DisplayString	read-only	Part Number of SFP's Hirschmann Information.
I32 hmSfpInfoVersion	1.3.6.1.4.1.248.14.1.1.13.1.20	Integer32	read-only	Version of SFP's Hirschmann Information. Contains -1 in case of a device read error.
I32 hmSfpMaxLength_copper	1.3.6.1.4.1.248.14.1.1.13.1.33	Integer32	read-only	Max. usable length for the cable type 'copper' with this SFP in units of meters.
I32 hmSfpMaxLength_fiber_50	1.3.6.1.4.1.248.14.1.1.13.1.31	Integer32	read-only	Max. usable length for the cable type '50/125 micrometer fiber' with this SFP in units of meters.
I32 hmSfpMaxLength_fiber_62_5	1.3.6.1.4.1.248.14.1.1.13.1.32	Integer32	read-only	Max. usable length for the cable type '62.5/125 micrometer fiber' with this SFP in units of meters.
I32 hmSfpMaxLength_fiber_9	1.3.6.1.4.1.248.14.1.1.13.1.30	Integer32	read-only	Max. usable length for the cable type '9/125 micrometer fiber' with this SFP in units of meters.
STR hmSfpPartNumber	1.3.6.1.4.1.248.14.1.1.13.1.7	DisplayString	read-only	The SFP's part description number (ASCII).
STR hmSfpPartRev	1.3.6.1.4.1.248.14.1.1.13.1.8	DisplayString	read-only	The SFP's part revision number (ASCII).
STR hmSfpRxPower	1.3.6.1.4.1.248.14.1.1.13.1.14	DisplayString	read-only	The SFP's internally measured Rx Power in units of milliWatts. (ASCII representation of floating point number).
NTF hmSFPRxPowerChangeTrap	1.3.6.1.4.1.248.14.1.0.14			This trap is sent when the state of the rx power of a SFP changes.
STR hmSfpRxPowerdBm	1.3.6.1.4.1.248.14.1.1.13.1.35	DisplayString	read-only	The SFP's internally measured Rx Power in units of dBm. (ASCII representation of floating point number).
I32 hmSfpRxPowerInt	1.3.6.1.4.1.248.14.1.1.13.1.16	Integer32	read-only	The SFP's internally measured Rx Power in units of 1/10 microWatts.
INT hmSfpRxPowerState	1.3.6.1.4.1.248.14.1.1.13.1.17	INTEGER	read-only	The state of the SFP's internally measured Rx.
STR hmSfpSerialNum	1.3.6.1.4.1.248.14.1.1.13.1.9	DisplayString	read-only	The SFP's serial number provided by vendor (ASCII).
T/F hmSfpSupported	1.3.6.1.4.1.248.14.1.1.13.1.24	TruthValue	read-only	Indicates if the local agent supports this SFP.
hmSFPTable	1.3.6.1.4.1.248.14.1.1.13		not-accessible	This table contains variables for each SFP.
I32 hmSfpTemperature	1.3.6.1.4.1.248.14.1.1.13.1.12	Integer32	read-only	This signed integer is used to identify the temperature within the SFP in units of centigrade (celsius). Contains -1000 in case of a device read error.
INT hmSfpTransceiver	1.3.6.1.4.1.248.14.1.1.13.1.4	INTEGER	read-only	The SFP's Transceiver type.
STR hmSfpTxPower	1.3.6.1.4.1.248.14.1.1.13.1.13	DisplayString	read-only	The SFP's internally measured Tx Power in units of milliWatts. (ASCII representation of floating point number).
STR hmSfpTxPowerdBm	1.3.6.1.4.1.248.14.1.1.13.1.34	DisplayString	read-only	The SFP's internally measured Tx Power in units of dBm. (ASCII representation of floating point number).
I32 hmSfpTxPowerInt	1.3.6.1.4.1.248.14.1.1.13.1.15	Integer32	read-only	The SFP's internally measured Tx Power in units of 1/10 microWatts.
STR hmSfpVendorName	1.3.6.1.4.1.248.14.1.1.13.1.6	DisplayString	read-only	The SFP's vendor name (ASCII).
OCT hmSfpVendorOUI	1.3.6.1.4.1.248.14.1.1.13.1.5	OCTET STRING	read-only	The SFP's vendor IEEE company ID (OUI).
hmSigConConfigEntry	1.3.6.1.4.1.248.14.2.12.1.1		not-accessible	The entry of the hmSigConConfigTable.
hmSigConConfigTable	1.3.6.1.4.1.248.14.2.12.1		not-accessible	This table contains all variables to configure the behaviour of the signalling contacts.
I32 hmSigConID	1.3.6.1.4.1.248.14.2.12.1.1.1	Integer32	read-only	This index is used to identify the associated signalling contact.
INT hmSigConLinkAlarm	1.3.6.1.4.1.248.14.2.12.2.1.2	INTEGER	read-write	Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.
hmSigConLinkEntry	1.3.6.1.4.1.248.14.2.12.2.1		not-accessible	The entry of the hmSigConLinkTable.
I32 hmSigConLinkID	1.3.6.1.4.1.248.14.2.12.2.1.1	Integer32	read-only	This index is used to identify the associated link and corresponds with ifMauIfIndex.
hmSigConLinkTable	1.3.6.1.4.1.248.14.2.12.2		not-accessible	This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifMauIfIndex. The table is also used for the device monitoring configuration.
INT hmSigConManualActivate	1.3.6.1.4.1.248.14.2.12.1.1.6	INTEGER	read-write	When operating in manual mode, the signal contact state can be set by this attribute.
INT hmSigConMode	1.3.6.1.4.1.248.14.2.12.1.1.5	INTEGER	read-write	This attribute specifies the behaviour of the relay contact. The factory settings for signal contact 1 is monitoring the correct operation of entries specified to be survied. When the device has also a second signal contact, the factory setting for it is the manual mode.
INT hmSigConOperState	1.3.6.1.4.1.248.14.2.12.1.1.7	INTEGER	read-only	This attribute shows the current operating state of the signal contact.
NTF hmSigConRelayChange	1.3.6.1.4.1.248.14.1.0.10			This trap is sent if the value of hmSigConOperState changes its value. Variables included in this trap are hmSigConOperState, hmSigConTrapCause, hmSigConTrapCauseIndex.
INT hmSigConSenseACANotInSync	1.3.6.1.4.1.248.14.2.12.1.1.23	INTEGER	read-write	Sets the monitoring whether the configuration on ACA is in sync with the configuration in NVRAM.
INT hmSigConSenseACARemoval	1.3.6.1.4.1.248.14.2.12.1.1.15	INTEGER	read-write	Sets the monitoring of the auto configuration adapter removal.
INT hmSigConSenseControlLine	1.3.6.1.4.1.248.14.2.12.1.1.9	INTEGER	read-write	Sets the monitoring of the ring/network coupling.
INT hmSigConSenseFan1State	1.3.6.1.4.1.248.14.2.12.1.1.18	INTEGER	read-write	Sets the monitoring of the cooling fan (platform dependant).
INT hmSigConSenseLinkFailure	1.3.6.1.4.1.248.14.2.12.1.1.8	INTEGER	read-write	Sets the monitoring of the network connection(s).
INT hmSigConSenseModuleRemoval	1.3.6.1.4.1.248.14.2.12.1.1.14	INTEGER	read-write	Sets the monitoring of module removal (platform dependant).
INT hmSigConSensePS1State	1.3.6.1.4.1.248.14.2.12.1.1.11	INTEGER	read-write	Sets the monitoring of the power supply 1.
INT hmSigConSensePS2State	1.3.6.1.4.1.248.14.2.12.1.1.12	INTEGER	read-write	Sets the monitoring of the power supply 2.
INT hmSigConSensePS3State	1.3.6.1.4.1.248.14.2.12.1.1.16	INTEGER	read-write	Sets the monitoring of the power supply 3 (platform dependant).
INT hmSigConSensePS4State	1.3.6.1.4.1.248.14.2.12.1.1.17	INTEGER	read-write	Sets the monitoring of the power supply 4 (platform dependant).
INT hmSigConSensePS5State	1.3.6.1.4.1.248.14.2.12.1.1.19	INTEGER	read-write	Sets the monitoring of the power supply 5 (platform dependant).
INT hmSigConSensePS6State	1.3.6.1.4.1.248.14.2.12.1.1.20	INTEGER	read-write	Sets the monitoring of the power supply 6 (platform dependant).
INT hmSigConSensePS7State	1.3.6.1.4.1.248.14.2.12.1.1.21	INTEGER	read-write	Sets the monitoring of the power supply 7 (platform dependant).
INT hmSigConSensePS8State	1.3.6.1.4.1.248.14.2.12.1.1.22	INTEGER	read-write	Sets the monitoring of the power supply 8 (platform dependant).
INT hmSigConSenseRedNotGuaranteed	1.3.6.1.4.1.248.14.2.12.1.1.10	INTEGER	read-write	Sets the monitoring of the HIPER-Ring.
INT hmSigConSenseTemperature	1.3.6.1.4.1.248.14.2.12.1.1.13	INTEGER	read-write	Sets the monitoring of the device temperature.
INT hmSigConTrapCause	1.3.6.1.4.1.248.14.2.12.1.1.3	INTEGER	read-only	This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hmSigConTrapCauseIndex.
I32 hmSigConTrapCauseIndex	1.3.6.1.4.1.248.14.2.12.1.1.4	Integer32	read-only	This attribute specifies the entity which produces the trap. 1 - n: index of powersupply table / interfaces table 0: other errors
INT hmSigConTrapEnable	1.3.6.1.4.1.248.14.2.12.1.1.2	INTEGER	read-write	Determines wether a trap shall be sent or not, when the signal contact operating state changes.
INT hmSigLinkAlarm	1.3.6.1.4.1.248.14.1.10.4.1.2	INTEGER	read-write	Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.
hmSigLinkEntry	1.3.6.1.4.1.248.14.1.10.4.1		not-accessible	The entry of the hmSigLinkTable.
I32 hmSigLinkID	1.3.6.1.4.1.248.14.1.10.4.1.1	Integer32	read-only	This index is used to identify the associated link and corresponds with ifMauIfIndex.
hmSigLinkTable	1.3.6.1.4.1.248.14.1.10.4		not-accessible	This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifMauIfIndex.
NTF hmSignallingRelay	1.3.6.1.4.1.248.14.1.0.4			This trap is sent if the value of hmRS2SigRelayState changes its value. Variables included in this trap are hmRS2SigRelayState, hmSigTrapReason, hmSigReasonIndex.
I32 hmSigReasonIndex	1.3.6.1.4.1.248.14.1.10.6	Integer32	read-only	This attribute specifies the entity which produces the trap. 1 - n: index of powersupply table / interfaces table 0: config-error.
OID hmSigTrapReason	1.3.6.1.4.1.248.14.1.10.5	OBJECT IDENTIFIER	read-only	This object identifies the reason for a trap. There are three reasons for a trap: hmRS2ConfigError ifMauMediaAvailable hmPSState The entity which produces the trap, is specified by hmSigReasonIndex.
NTF hmSNTPTrap	1.3.6.1.4.1.248.14.2.0.6			This trap reports SNTP error conditions. For a list of possible error conditions refer to hmNetSNTPOperStatus.
NTF hmStandby	1.3.6.1.4.1.248.14.1.0.5			This trap is sent if the value of hmRS2OperMode changes.
hmSwitchResources	1.3.6.1.4.1.248.14.2.15
INT hmSysBOOTPEnable	1.3.6.1.4.1.248.14.1.1.23	INTEGER	read-write	Enable/Disable BOOTP operation. A (1) enables, a (2) disables. When disabled, no BOOTPs are transmitted by the system. When enabled, the system sends BOOTP requests at booting.
STR hmSysChassisName	1.3.6.1.4.1.248.14.1.1.20	DisplayString	read-write	This displaystring represents the name of the Chassis. Any change of this variable will cause an automatically update of this value on each Basic Board in this Chassis.
INT hmSysDHCPEnable	1.3.6.1.4.1.248.14.1.1.24	INTEGER	read-write	Enable/Disable DHCP operation. A (1) enables, a (2) disables. When disabled, no DHCPs are transmitted by the system. When enabled, the system sends DHCP requests at booting.
INT hmSysFlowControl	1.3.6.1.4.1.248.14.1.1.22	INTEGER	read-write	enables or disables flow control for the switch unit.
INT hmSysGroupAction	1.3.6.1.4.1.248.14.1.1.9.1.7	INTEGER	read-write	This object, when read, always returns a value of other(1). A value of reset(2) has the same effect as a power-on sequence (coldstart). When set to resetStats(3), a reset of all statistic counters of the card's ports will be forced. Any other value results in a badValue status code.
I32 hmSysGroupActionDelayCurrent	1.3.6.1.4.1.248.14.1.1.9.1.12	Integer32	read-only	If a delayed reset is scheduled this object will incrementing from the start value to zero.
I32 hmSysGroupActionDelayPreset	1.3.6.1.4.1.248.14.1.1.9.1.11	Integer32	read-write	Time in seconds until a reset(2) or hotRestart(10) that was triggered over the hmSysGroupAction object is executed. Writing a zero will cancel any scheduled reset.
I32 hmSysGroupActionResult	1.3.6.1.4.1.248.14.1.1.9.1.8	Integer32	read-only	Result of the last activated action. A value of zero indicates that the result is ok. Bits set in the result indicate error conditions.
I32 hmSysGroupCapacity	1.3.6.1.4.1.248.14.1.1.3	Integer32	read-only	The hmSysGroupCapacity is the number of groups that can be contained within the chassis. Within each managed chassis/switch, the groups are uniquely numbered in the range from 1 to hmSysGroupCapacity. Some groups may not be present in the chassis, in which case the actual number of groups present will be less than hmSysGroupCapacity. The number of groups present will never be greater than hmSysGroupCapacity.
STR hmSysGroupDescription	1.3.6.1.4.1.248.14.1.1.9.1.3	DisplayString	read-only	Description of interface card.
hmSysGroupEntry	1.3.6.1.4.1.248.14.1.1.9.1		not-accessible	The entry of the hmSysGroupTable.
STR hmSysGroupHwVersion	1.3.6.1.4.1.248.14.1.1.9.1.4	DisplayString	read-only	Hardware version of interface card.
I32 hmSysGroupID	1.3.6.1.4.1.248.14.1.1.9.1.1	Integer32	read-only	index to identify an interface card. This value is never greater than hmSysGroupCapacity.
INT hmSysGroupIsolateMode	1.3.6.1.4.1.248.14.1.1.9.1.9	INTEGER	read-write	Setting this variable to enable(1) separates the group from the rest of the chassis, so that it will act like a standalone-switch.
STR hmSysGroupMap	1.3.6.1.4.1.248.14.1.1.4	DisplayString	read-only	This string represents the current configuration of the chassis, encoded as an octet string. Each module is represented by a single octet. If the value of a single octet is the ascii representation of the character '1', it indicates that the module represented by that octet is present, if '0', the module is absent. The number of octets in the string is given by hmSysGroupCapacity. If the value of this variable changes, a hmGroupMapChange trap is sent.
I32 hmSysGroupModuleCapacity	1.3.6.1.4.1.248.14.1.1.7	Integer32	read-only	Maximum number of modules that an individual group can contain in this system.
STR hmSysGroupModuleMap	1.3.6.1.4.1.248.14.1.1.9.1.6	DisplayString	read-only	This string represents the current configuration of a group, encoded as an octet string. Each module is represented by a single octet. If the value of a single octet is the ascii representation of the character '1', it indicates that the module represented by that octet is present, if '0', the module is absent. If the character is 'C', then the card is configurable but absent. The ports can be configured and by setting hmSysModStatus to remove(3) the card can be logically removed. The number of bytes in the string is given by hmSysGroupModuleCapacity.
STR hmSysGroupSerialNum	1.3.6.1.4.1.248.14.1.1.9.1.10	DisplayString	read-only	The serial number provided by vendor (ASCII).
STR hmSysGroupSwVersion	1.3.6.1.4.1.248.14.1.1.9.1.5	DisplayString	read-only	Software version of interface card.
hmSysGroupTable	1.3.6.1.4.1.248.14.1.1.9		not-accessible	This table contains variables for a closer description of a group.
INT hmSysGroupType	1.3.6.1.4.1.248.14.1.1.9.1.2	INTEGER	read-only	Type of interface card.
INT hmSysHTTPEnable	1.3.6.1.4.1.248.14.1.1.26	INTEGER	read-write	Enable/Disable HTTP connection. A (1) enables, a (2) disables. When disabled, no HTTP is allowed by the system.
INT hmSysHttpsEnable	1.3.6.1.4.1.248.14.1.1.44	INTEGER	read-write	Enables/Disables HTTPS access to the device. A (1) enables, a (2) disables.
INT hmSysHttpsPortNumber	1.3.6.1.4.1.248.14.1.1.45	INTEGER	read-write	The port number of the HTTPS web server.
I32 hmSysMaxFan	1.3.6.1.4.1.248.14.1.1.6	Integer32	read-only	Maximum number of fans for this chassis. Within each managed chassis/switch, the fans are uniquely numbered in the range from 0 to hmSysMaxFan.
I32 hmSysMaxPowerSupply	1.3.6.1.4.1.248.14.1.1.5	Integer32	read-only	Maximum number of power supplies for this chassis. Within each managed chassis/switch, the groups are uniquely numbered in the range from 1 to hmSysMaxPowerSupply.
I32 hmSysMaxSignalContacts	1.3.6.1.4.1.248.14.1.1.43	Integer32	read-only	Maximum number of signal contacts for this chassis. Within each managed chassis/switch, the groups are uniquely numbered in the range from 1 to hmSysMaxSignalContacts.
I32 hmSysMaxTrunks	1.3.6.1.4.1.248.14.1.1.37	Integer32	read-only	Maximum number of trunks for this chassis.
I32 hmSysMaxUSBPorts	1.3.6.1.4.1.248.14.1.1.39.1	Integer32	read-only	Maximum number of USB ports in this chassis.
STR hmSysModDescription	1.3.6.1.4.1.248.14.1.1.10.1.4	DisplayString	read-only	Description of the module.
I32 hmSysModFirstMauIndex	1.3.6.1.4.1.248.14.1.1.10.1.7	Integer32	read-only	value of the first mauIndex used by the module.
I32 hmSysModGroupID	1.3.6.1.4.1.248.14.1.1.10.1.1	Integer32	read-only	index to identify an interface card. This value is never greater than hmSysGroupCapacity.
I32 hmSysModID	1.3.6.1.4.1.248.14.1.1.10.1.2	Integer32	read-only	index to identify a module on an interface card. This value is never greater than hmSysGroupModuleCapacity.
I32 hmSysModNumOfPorts	1.3.6.1.4.1.248.14.1.1.10.1.6	Integer32	read-only	The numberOfPorts is the number of ports contained within the module. Within each module, the ports are uniquely numbered in the range from 1 to numberOfPorts.
STR hmSysModSerialNum	1.3.6.1.4.1.248.14.1.1.10.1.9	DisplayString	read-only	The serial number provided by vendor (ASCII).
INT hmSysModStatus	1.3.6.1.4.1.248.14.1.1.10.1.8	INTEGER	read-write	status of hot-pluggable modules, only for PowerMICE. If the value is physical(1), then the module is plugged in, if the value is configurable, the ports can be configured, but the card is absent, with the value remove(3) written to the agent the card can be logically removed.
INT hmSysModType	1.3.6.1.4.1.248.14.1.1.10.1.3	INTEGER	read-only	Type of a module.
hmSysModuleEntry	1.3.6.1.4.1.248.14.1.1.10.1		not-accessible	The entry of the hmSysModuleTable.
I32 hmSysModulePortCapacity	1.3.6.1.4.1.248.14.1.1.8	Integer32	read-only	Maximum number of ports that an individual module can contain in this system.
hmSysModuleTable	1.3.6.1.4.1.248.14.1.1.10		not-accessible	This table contains variables for a closer description of a module.
STR hmSysModVersion	1.3.6.1.4.1.248.14.1.1.10.1.5	DisplayString	read-only	version of the module.
hmSysOEMGroup	1.3.6.1.4.1.248.14.1.1.42
I32 hmSysOEMID	1.3.6.1.4.1.248.14.1.1.42.1	Integer32	read-only	Unique OEM ID.
INT hmSysPlugAndPlay	1.3.6.1.4.1.248.14.1.1.27	INTEGER	read-write	Enable/Disable Plug&Play feature. A (1) enables, a (2) disables. if this variable is set to enable(1), special Plug&Play actions are performed at boot time and after a successful completion the value is automatically reset to the disable(2) state.
INT hmSysProduct	1.3.6.1.4.1.248.14.1.1.1	INTEGER	read-only	Manufacturer-defined product identifier.
hmSysSelftestGroup	1.3.6.1.4.1.248.14.1.1.41
INT hmSysSelftestMMUStatus	1.3.6.1.4.1.248.14.1.1.41.3	INTEGER	read-only	Status of the memory managment unit.
NTF hmSysSelftestPortError	1.3.6.1.4.1.248.14.2.0.16			This trap is sent when the agent wants to reboot due to Opal Workaround 4. It shows that the specific port is in an error state and a device reboot is needed.
INT hmSysSelftestRAM	1.3.6.1.4.1.248.14.1.1.41.1	INTEGER	read-write	Controls RAM selftest on coldstart of the device. When disabled the device booting time is reduced.
INT hmSysSelftestRebootOnError	1.3.6.1.4.1.248.14.1.1.41.2	INTEGER	read-write	If enabled the software does make a reboot if there is a serious error detected.
NTF hmSysSelftestRebootOnErrorTrap	1.3.6.1.4.1.248.14.1.0.15			This trap is sent when the agent wants to reboot due to an internal circumstance.
INT hmSysSelftestRebootOnHdxError	1.3.6.1.4.1.248.14.1.1.41.4	INTEGER	read-write	If enabled the software does a reboot if there is a Half duplex mismatch error is detected. The option depends on hmSysSelftestRebootOnError.
INT hmSysSkipAcaOnBoot	1.3.6.1.4.1.248.14.1.1.46	INTEGER	read-write	Enable/disable loading from ACA on startup.
STR hmSysSoftwareCapability	1.3.6.1.4.1.248.14.1.1.34	DisplayString	read-only	This variable shows the capability of the running software. The string is formated as follow: Byte 1 : Always L (for Layer) Byte 2 : 2 or 3 (dependend if the software supports onyl switching (2) or also routing (3)) Byte 3 : E or P (Enhanced or Professional software functionality)
INT hmSysStpBPDUGuardEnable	1.3.6.1.4.1.248.14.1.1.32	INTEGER	read-write	This variable controls the BPDU Guard operation of the entire switch (globally). To control the BPDU Guard function of each port use hmIfaceStpBpduGuardEnable. If BPDU guard functionality are global enabled (hmSysStpBPDUGuardEnable=enable(1)), and BPDU guard are enabled per port (hmIfaceStpBpduGuardEnable=enable(1)) and (R)STP are globally enabled and an BPDU are received on the port, then hmIfaceStpBpduGuardStatus is set to true(1) for this port and IfAdminStatus is set to down(2) for this port. Variable hmIfaceStpBpduGuardStatus can be reset (to their original values (=false)) with switching BPDU guard functionality globally off (hmSysStpBPDUGuardEnable=disable(2)). IfAdminStatus can be again reset to to their original values up() only manually. The default value of hmSysStpBPDUGuardEnable is disable(2).
INT hmSysStpEnable	1.3.6.1.4.1.248.14.1.1.21	INTEGER	read-write	This variable controls the STP operation of the entire switch. To control the STP function of each port use hmIfaceStpEnable
I32 hmSysSTPErrorNumber	1.3.6.1.4.1.248.14.1.1.33	Integer32	read-only	Advertised the reason why (R)STP could not be switched on. Error reasons are coded as OR operation bit by bit, see values: 0x00 - no errors - (R)STP is switched on, 0x01 - (R)STP cannot be switched on, because of standby mode, 0x02 - (R)STP cannot be switched on, because of kopp Local Active, 0x04 - (R)STP cannot be switched on, because of kopp Slave Active, 0x08 - (R)STP cannot be switched on, because of kopp Master Active, 0x10 - (R)STP cannot be switched on, because of sysRingOn and sysRMMode, 0x20 - (R)STP cannot be switched on, because of error if BB_SetParameter is occured.
INT hmSysSwitchAddressRelearnDetection	1.3.6.1.4.1.248.14.1.1.40.4	INTEGER	read-write	Controls if detection of address relearns is enabled or not.
I32 hmSysSwitchAddressRelearnThreshold	1.3.6.1.4.1.248.14.1.1.40.5	Integer32	read-write	The value of relearnd addresses to signal address relearn threshold exceeded.
INT hmSysSwitchDuplexMismatchDetection	1.3.6.1.4.1.248.14.1.1.40.6	INTEGER	read-write	Controls if duplex mismatch detection is enabled or not.
INT hmSysSwitchFastLinkDetection	1.3.6.1.4.1.248.14.1.1.40.3	INTEGER	read-write	Controls if the fast link detection is enabled or not.
C32 hmSysSwitchFDBFullCounter	1.3.6.1.4.1.248.14.1.1.40.7	Counter32	read-only	The number of FDB Full indications that the agent has detected since reboot.
I32 hmSysSwitchFDBHashOptimizingMode	1.3.6.1.4.1.248.14.1.1.40.8	Integer32	read-write	Mode to optimize the MAC address table hashing algorithm. Which modes can be configured is hardware dependend. After configuration a reboot is needed.
I32 hmSysSwitchFDBHashOptimizingStatus	1.3.6.1.4.1.248.14.1.1.40.9	Integer32	read-only	Shows the current hash mode of this device.
hmSysSwitchGroup	1.3.6.1.4.1.248.14.1.1.40
INT hmSysSwitchLearning	1.3.6.1.4.1.248.14.1.1.40.1	INTEGER	read-write	Controls address learning by the switch. When disabled the address database of the switch will not be updated with dynamic filtering entries. Static Filtering Entries and Group Registration Entries are not affected.
INT hmSysSwitchMRU	1.3.6.1.4.1.248.14.1.1.40.2	INTEGER	read-write	The Maximum Receive Unit MRU that can be received by the switch.
hmSysSwitchRedundancyGroup	1.3.6.1.4.1.248.14.1.1.40.20
T/F hmSysSwitchRedundancyRstpMrpConfigError	1.3.6.1.4.1.248.14.1.1.40.20.2	TruthValue	read-only	This object indicates a Rstp Mrp fail configuration if the value true is shown.
BRI hmSysSwitchRedundancyRstpMrpConfigErrorBridge	1.3.6.1.4.1.248.14.1.1.40.20.3	BridgeIdOrNull	read-only	The identifier of the device which has a Rstp Mrp fail configuration or Null if there is no fail configuration.
INT hmSysSwitchRedundancyRstpMrpMode	1.3.6.1.4.1.248.14.1.1.40.20.1	INTEGER	read-write	Rstp Mrp is enabled if this object is set to enable(1). Rstp Mrp is disabled if this object is set to disable(2).
INT hmSysSwitchServiceMode	1.3.6.1.4.1.248.14.1.1.40.11.1	INTEGER	read-write	Enables the service mode. If enabled, the switch can be separated into two switching areas with the redundant power supply. The two HIPER Ring ports are in area one. The other ports are in area two. Area one is VLAN capable, area two is not VLAN capable.
hmSysSwitchServiceModeGroup	1.3.6.1.4.1.248.14.1.1.40.11
INT hmSysSwitchServiceModeOperState	1.3.6.1.4.1.248.14.1.1.40.11.3	INTEGER	read-only	If enabled, the switch has been separated into two switching areas with the redundant power supply. The two HIPER Ring ports are in area one. The other ports are in area two. Area one is VLAN capable, area two is not VLAN capable.
I32 hmSysSwitchServiceVlan	1.3.6.1.4.1.248.14.1.1.40.11.2	Integer32	read-write	Defined the Vlan for the service mode. The Vlan must be a valid Vlan and neither Vlan 0 (mgmt vlan) nor Vlan 1 (Default Vlan).
hmSysSwitchVLANGroup	1.3.6.1.4.1.248.14.1.1.40.10
INT hmSysSwitchVLANLearningMode	1.3.6.1.4.1.248.14.1.1.40.10.1	INTEGER	read-write	Controls the VLAN learning mode by the switch. When set to IVL Independend VLAN Learning is active. When set to SVL Shared VLAN Learning is active. After setting this variable the switch have to be restarted.
INT hmSysSwitchVLANLearningStatus	1.3.6.1.4.1.248.14.1.1.40.10.2	INTEGER	read-only	Shows the current VLAN learning mode. When set to IVL Independend VLAN Learning is active. When set to SVL Shared VLAN Learning is active.
INT hmSysTelnetEnable	1.3.6.1.4.1.248.14.1.1.25	INTEGER	read-write	Enable/Disable Telnet operation. A (1) enables, a (2) disables. When disabled, no Telnet sessions are allowed by the system.
hmSystemTable	1.3.6.1.4.1.248.14.1.1
TIK hmSystemTime	1.3.6.1.4.1.248.14.1.1.30	TimeTicks	read-write	Time measured in seconds since 00:00:00 UTC, January 1, 1970. The clock of the agents may be set using this variable. Changing this variable on one agent automatically updates the value on the other agents in the same chassis.
INT hmSystemTimeSource	1.3.6.1.4.1.248.14.1.1.31	INTEGER	read-only	Shows the source of the system time.
hmSysUSBGroup	1.3.6.1.4.1.248.14.1.1.39
STR hmSysVersion	1.3.6.1.4.1.248.14.1.1.2	DisplayString	read-only	This value is a string that contains at least the following data : SW: Version number of software CH: Version number of chassis BP: Version number of backplane
I32 hmTemperature	1.3.6.1.4.1.248.14.2.5.1	Integer32	read-only	This signed integer is used to identify the temperature within the agent in units of centigrade (celsius).
NTF hmTemperatureTrap	1.3.6.1.4.1.248.14.2.0.1			This trap is sent if the value of hmTemperature leaves or enters the range of the agent temperature threshholds hmTempUprLimit and hmTempLwrLimit.
I32 hmTempLwrLimit	1.3.6.1.4.1.248.14.2.5.3	Integer32	read-write	This value is used to define a minimum level for the temperature within a concentrator. If the temperature falls below this lower limit, the management station will be notified by a hmTemperature trap.
hmTempTable	1.3.6.1.4.1.248.14.2.5
I32 hmTempUprLimit	1.3.6.1.4.1.248.14.2.5.2	Integer32	read-write	This value is used to define a maximum level for the temperature within an agent. If the temperature rises above this upper limit, the management station will be notified by a hmTemperature trap.
INT hmTrapCommAuthentication	1.3.6.1.4.1.248.14.2.8.3.1.6	INTEGER	read-write	Enable (1) or Disable (2) the SNMP Authentication traps for this SNMP community.
INT hmTrapCommBridge	1.3.6.1.4.1.248.14.2.8.3.1.7	INTEGER	read-write	Enable (1) or Disable (2) the SNMP Bridge MIB traps for this SNMP community. Available Traps: newRoot (MACH) topologyChange (MACH)
INT hmTrapCommChassis	1.3.6.1.4.1.248.14.2.8.3.1.11	INTEGER	read-write	Enable (1) or Disable (2) the SNMP Enterprise chassis traps for this SNMP community. Available Traps: hmGroupMapChange (MACH) hmPowerSupply (MACH, MICE, RS2) hmFan (MACH) hmSignallingRelay (MICE, RS2) hmStandby (MACH, MICE, RS2) hmSelfTestError (MACH) hmModuleMapChange (MICE) hmTemperature (MACH) hmLoginTrap (MACH) hmDuplicateStaticAddressTrap (MACH)
INT hmTrapCommColdStart	1.3.6.1.4.1.248.14.2.8.3.1.3	INTEGER	read-write	Enable (1) or Disable (2) the SNMP ColdStart Trap for this SNMP community.
I32 hmTrapCommCommIndex	1.3.6.1.4.1.248.14.2.8.3.1.2	Integer32	read-write	The communities entry index of this SNMP Trap Community Entry.
INT hmTrapCommDualHoming	1.3.6.1.4.1.248.14.2.8.3.1.10	INTEGER	read-write	Enable (1) or Disable (2) the SNMP Enterprise dual homing traps for this SNMP community. Available Traps: hmDuHmReconfig (MACH) hmDuHmRedundancy (MACH) hmRingRedReconfig (MACH, MICE)
hmTrapCommEntry	1.3.6.1.4.1.248.14.2.8.3.1		not-accessible	A list of SNMP Trap Community properties.
I32 hmTrapCommIndex	1.3.6.1.4.1.248.14.2.8.3.1.1	Integer32	read-only	An index that uniquely identifies an ordered entry in the SNMP Community Trap Table.
INT hmTrapCommLinkDown	1.3.6.1.4.1.248.14.2.8.3.1.4	INTEGER	read-write	Enable (1) or Disable (2) the SNMP Link Down traps for this SNMP community.
INT hmTrapCommLinkUp	1.3.6.1.4.1.248.14.2.8.3.1.5	INTEGER	read-write	Enable (1) or Disable (2) the SNMP Link Up traps for this SNMP community.
INT hmTrapCommRMON	1.3.6.1.4.1.248.14.2.8.3.1.8	INTEGER	read-write	Enable (1) or Disable (2) the SNMP RMON traps for this SNMP community. Available Traps: risingAlarm (MACH, MICE, RS2) fallingAlarm (MACH, MICE, RS2)
INT hmTrapCommState	1.3.6.1.4.1.248.14.2.8.3.1.12	INTEGER	read-write	The state of this community entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that is no longer valid (e.g., an entry that was deleted) and should be ignored. An attempt to set a value of invalid (4) causes the agent to return SNMP_BADVALUE.
hmTrapCommTable	1.3.6.1.4.1.248.14.2.8.3		not-accessible	A list of valid SNMP Community Entries used for Traps.
I32 hmTrapCommTableEntriesMax	1.3.6.1.4.1.248.14.2.8.1	Integer32	read-only	The total number of entries in the hmTrapCommTable. This value equates to the total number of communities which potentially can be recognized.
INT hmTrapCommUsergroup	1.3.6.1.4.1.248.14.2.8.3.1.9	INTEGER	read-write	Enable (1) or Disable (2) the SNMP Enterprise usergroup traps for this SNMP community. Available Traps: hmNewUserTrap (MACH) hmPortSecurityTrap (MACH, MICE, RS2) hmPortSecConfigErrorTrap (MACH)
I32 hmTrapDestCommIndex	1.3.6.1.4.1.248.14.2.8.4.1.3	Integer32	read-write	The communities entry index of this SNMP Trusted Host Destination Entry's community.
hmTrapDestEntry	1.3.6.1.4.1.248.14.2.8.4.1		not-accessible	A list of SNMP Trap Trusted Host Destination properties.
I32 hmTrapDestIndex	1.3.6.1.4.1.248.14.2.8.4.1.1	Integer32	read-only	An index that uniquely identifies an ordered entry in the SNMP Trusted Host Destination Table.
IP hmTrapDestIpAddress	1.3.6.1.4.1.248.14.2.8.4.1.4	IpAddress	read-write	The IP Address for the host. This identified host has permission to access information in this device's MIB tables, providing the SNMP security toggle is on (see hmMiscSNMPSecurity).
IP hmTrapDestIpMask	1.3.6.1.4.1.248.14.2.8.4.1.5	IpAddress	read-write	The Network Mask for the trusted Host Destination entry.
STR hmTrapDestName	1.3.6.1.4.1.248.14.2.8.4.1.2	DisplayString	read-write	The name of this SNMP Trusted Host Destination Entry, e.g. Admin.
INT hmTrapDestState	1.3.6.1.4.1.248.14.2.8.4.1.6	INTEGER	read-write	The state of this trusted trap destination entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that is no longer valid (e.g., an entry that was deleted) and should be ignored. An attempt to set a value of invalid (4) causes the agent to return SNMP_BADVALUE.
hmTrapDestTable	1.3.6.1.4.1.248.14.2.8.4		not-accessible	A list of valid SNMP Trap Trusted Host Destination entries.
I32 hmTrapDestTableEntriesMax	1.3.6.1.4.1.248.14.2.8.2	Integer32	read-only	The total number of entries in the hmTrapDestTable. This equates to the total number of hosts which can potentially be sent SNMP traps.
hmTrapGroup	1.3.6.1.4.1.248.14.2.8
INT hmTrunkAction	1.3.6.1.4.1.248.14.1.1.12.1.4	INTEGER	read-write	action according to hmIfaceAction which is performed for all interfaces in the trunk
INT hmTrunkAdminStatus	1.3.6.1.4.1.248.14.1.1.12.1.5	INTEGER	read-write	The desired state of the trunk. if this variable is set to down(2), all interfaces which are aggregated in the trunk are switched off simultaneously. Reading this variable returns up(1) if at least one interface of the trunk is operational (up).
hmTrunkEntry	1.3.6.1.4.1.248.14.1.1.12.1		not-accessible	The entry of the hmTrunkTable.
I32 hmTrunkID	1.3.6.1.4.1.248.14.1.1.12.1.1	Integer32	read-only	Index to identify a link aggregation instance
OCT hmTrunkInterfaces	1.3.6.1.4.1.248.14.1.1.12.1.2	OCTET STRING	read-only	List of interfaces which are aggregated in the trunk. each octet pair contains the slotID and interfaceID. Interfaces are added or deleteted using the variable hmIfaceTrunkID.
TIK hmTrunkLastChange	1.3.6.1.4.1.248.14.1.1.12.1.7	TimeTicks	read-only	Time since system boot when there was a change in either the operational state of the trunk or the list of aggregated interfaces.
STR hmTrunkName	1.3.6.1.4.1.248.14.1.1.12.1.3	DisplayString	read-write	Textual description of the trunk
INT hmTrunkOperStatus	1.3.6.1.4.1.248.14.1.1.12.1.6	INTEGER	read-only	The operational state of the trunk. Reading this variable returns up(1) if at least one interface of the trunk is operational (up).
hmTrunkTable	1.3.6.1.4.1.248.14.1.1.12		not-accessible	This table contains variables for each trunk of the switch.
INT hmUserGroupStatus	1.3.6.1.4.1.248.14.1.11.5.1	INTEGER	read-only	state of the user group configuration
mach100	1.3.6.1.4.1.248.14.10.110
mach1000ge	1.3.6.1.4.1.248.14.10.131
mach100ge	1.3.6.1.4.1.248.14.10.130
mach3000	1.3.6.1.4.1.248.14.10.3
mach4002_24G	1.3.6.1.4.1.248.14.10.70
mach4002_24G_3X	1.3.6.1.4.1.248.14.10.71
mach4002_48_4G	1.3.6.1.4.1.248.14.10.50
mach4002_48G	1.3.6.1.4.1.248.14.10.75
mach4002_48G_3X	1.3.6.1.4.1.248.14.10.76
ms20	1.3.6.1.4.1.248.14.10.30
ms2108_2	1.3.6.1.4.1.248.14.10.4
ms30	1.3.6.1.4.1.248.14.10.31
ms3124_4	1.3.6.1.4.1.248.14.10.5
ms4128_5	1.3.6.1.4.1.248.14.10.10
octopus	1.3.6.1.4.1.248.14.10.60
octopus_os	1.3.6.1.4.1.248.14.10.120
osb20	1.3.6.1.4.1.248.14.10.45
railswitchrugged	1.3.6.1.4.1.248.14.10.100
rr_epl	1.3.6.1.4.1.248.14.10.21
rs2	1.3.6.1.4.1.248.14.10.2
rs2_16	1.3.6.1.4.1.248.14.10.6
rs2_4r	1.3.6.1.4.1.248.14.10.7
rs20	1.3.6.1.4.1.248.14.10.40
rs30	1.3.6.1.4.1.248.14.10.41
rsb20	1.3.6.1.4.1.248.14.10.44
ruggedswitch	1.3.6.1.4.1.248.14.10.90

RFC description

Hirschmann private MIB module defining SNMP management objects for Hirschmann Platform Layer 2 switches and ring management.

Start monitoring Hirschmann modular industrial Ethernet switch (e.g. RSPE-Expandable/MACH104 series) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HMPRIV-MGMT-SNMP-MIB

What Is HMPRIV-MGMT-SNMP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description