All MIBs › CISCO-SRP-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2005-12-19
Category: Cisco Devices, Network Interfaces, Optical and WDM
Description: Manages Spatial Reuse Protocol (SRP/DPT) ring interfaces and topology discovery on Cisco dynamic packet transport rings.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-SRP-MIB?
CISCO-SRP-MIB manages Spatial Reuse Protocol (SRP), also known as Dynamic Packet Transport (DPT), a Cisco ring-topology WAN technology, and belongs to Cisco's optical/ring-interface MIB family. It exposes MAC-layer identity data for SRP interfaces along with ring-level, host-level, and error counters describing traffic flow around the dual counter-rotating ring and any faults encountered. Its monitoring value is centered on interface/link performance and fault status rather than environmental hardware sensors: administrators track srpRingCounters and srpHostCounters to gauge ring traffic load and srpErrorsCounters to detect ring wraps, fiber cuts, or protocol errors, with traps under srpTrapsNotifications alerting to ring topology changes or failures. It builds on standard interface conventions (ifIndex/IF-MIB) to associate SRP counters with the underlying physical interface. It is deployed on Cisco DPT/SRP ring interface cards used in metro and long-haul optical ring networks. Engineers searching for cisco srp monitoring should note SRP here refers to Spatial Reuse Protocol/Dynamic Packet Transport, Cisco's ring-topology WAN technology, not Session Recording Protocol or other unrelated "SRP" acronyms.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-SRP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco DPT/SRP ring interface routers
Monitoring Examples
An operator would poll srpRingCounters and srpHostCounters on an SRP interface identified by srpMAC to baseline normal ring traffic levels, then watch srpErrorsCounters for a spike indicating ring errors such as wrap events or corrupted frames. A trap fired from srpTrapsNotifications would immediately flag a ring topology change, such as a fiber cut causing the ring to wrap and reroute traffic the long way around.
What Can Be Monitored
- SRP interface MAC address
- ring traffic counters
- host traffic counters
- ring error counters
- ring topology change/failure notifications
This MIB depends on
Related MIBs
Imported Objects
From CISCO-SMI
| ciscoExperiment | OBJECT-IDENTITY |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using srpMACIpsWrapCounter OID:
Select a Cisco DPT/SRP ring interface router as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type srpMACIpsWrapCounter into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of transition from unwrap to wrap state. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscosrpMIB | 1.3.6.1.4.1.9.10.60 | The MIB module to describe objects for Spatial Reuse Protocol (SRP) interface layer. | ||
| srpCompliance | 1.3.6.1.4.1.9.10.60.6.2.1 | The compliance statement for this MIB. | ||
| srpComplianceOld | 1.3.6.1.4.1.9.10.60.6.2.2 | A compliance statement whose only purpose is to list explicitly the deprecated groups. | ||
| srpCompliances | 1.3.6.1.4.1.9.10.60.6.2 | |||
| srpConformance | 1.3.6.1.4.1.9.10.60.6 | |||
| srpErrCntCurrEntry | 1.3.6.1.4.1.9.10.60.4.3.1 | not-accessible | Errors statistics for the current interval of a particular side of a particular SRP interface. The corresponding instance of srpIfTimeElapsed indicates the number of seconds which have elapsed so far in the current interval. | |
| srpErrCntCurrGroup | 1.3.6.1.4.1.9.10.60.6.1.11 | A collection of objects providing information about received errors, in the current 15 minute interval. | ||
| PER srpErrCntCurrHostRxDiscardPkts | 1.3.6.1.4.1.9.10.60.4.3.1.7 | PerfCurrentCount64 | read-only | The counter associated with the current number of packets which were prevented from being delivered to the Higher Layer because of a resource limitation, in the current 15 minute interval. |
| PER srpErrCntCurrHostRxGiantPkts | 1.3.6.1.4.1.9.10.60.4.3.1.9 | PerfCurrentCount64 | read-only | The counter associated with the current number of packets discarded because of being too big for the higher layer, in the current 15 minute interval. |
| PER srpErrCntCurrHostRxShortPkts | 1.3.6.1.4.1.9.10.60.4.3.1.8 | PerfCurrentCount64 | read-only | The counter associated with the current number of packets which were prevented from being delivered to the Higher Layer because of being too short, in the current 15 minute interval. |
| NUM srpErrCntCurrInterfaceSide | 1.3.6.1.4.1.9.10.60.4.3.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| PER srpErrCntCurrRingRxAbortPkts | 1.3.6.1.4.1.9.10.60.4.3.1.5 | PerfCurrentCount64 | read-only | The counter associated with the current number of aborted packets, received from the Physical medium dependent layer in the current 15 minute interval. Aborted packets are packets that have been aborted by an abort sequence code. |
| PER srpErrCntCurrRingRxCRC | 1.3.6.1.4.1.9.10.60.4.3.1.6 | PerfCurrentCount64 | read-only | The counter associated with the current number of packets with CRC errors, received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpErrCntCurrRingRxGiantPkts | 1.3.6.1.4.1.9.10.60.4.3.1.4 | PerfCurrentCount64 | read-only | The counter associated with the number of giant packets, received from the Physical medium dependent layer in the current 15 minute interval. A giant packet is larger than max size packet, which is 9216 octets. |
| PER srpErrCntCurrRingRxShortPkts | 1.3.6.1.4.1.9.10.60.4.3.1.3 | PerfCurrentCount64 | read-only | The counter associated with the number of short packets, received from the Physical medium dependent layer in the current 15 minute interval. A short packet is 16 octets or less. |
| PER srpErrCntCurrRingRxTtlExpPkts | 1.3.6.1.4.1.9.10.60.4.3.1.2 | PerfCurrentCount64 | read-only | The counter associated with the number of packets discarded due to TTL expiry, received from the Physical medium dependent layer in the current 15 minute interval. |
| srpErrCntCurrTable | 1.3.6.1.4.1.9.10.60.4.3 | not-accessible | The SRP Errors Current counters table. | |
| srpErrCntIntEntry | 1.3.6.1.4.1.9.10.60.4.4.1 | not-accessible | Error statistics collected for a particular interval of a particular side of a particular SRP interface. The number of 15-minute intervals is between 1 and 96, and identifies the intervals for which the set of statistics is available. The value of srpIfValidIntervals indicates how many intervals are currently available. | |
| srpErrCntIntGroup | 1.3.6.1.4.1.9.10.60.6.1.12 | A collection of objects providing information about received errors, in a particular 15-minute interval in the past 24 hours. | ||
| NUM srpErrCntIntHostRxDiscardPkts | 1.3.6.1.4.1.9.10.60.4.4.1.8 | PerfIntervalCount64 | read-only | The counter associated with the interval number of packets discarded due to resource limitations, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpErrCntIntHostRxGiantPkts | 1.3.6.1.4.1.9.10.60.4.4.1.10 | PerfIntervalCount64 | read-only | The counter associated with the interval number of packets discarded because of being too big for the higher layer, in a particular 15-minute interval in the past 24 hours. |
| NUM srpErrCntIntHostRxShortPkts | 1.3.6.1.4.1.9.10.60.4.4.1.9 | PerfIntervalCount64 | read-only | The counter associated with the interval number of packets discarded because of being too short for the higher layer, in a particular 15-minute interval in the past 24 hours. |
| NUM srpErrCntIntInterfaceSide | 1.3.6.1.4.1.9.10.60.4.4.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| I32 srpErrCntIntNumber | 1.3.6.1.4.1.9.10.60.4.4.1.2 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set od statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM srpErrCntIntRingRxAbortPkts | 1.3.6.1.4.1.9.10.60.4.4.1.6 | PerfIntervalCount64 | read-only | The counter associated with the interval number of aborted packets, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpErrCntIntRingRxCRC | 1.3.6.1.4.1.9.10.60.4.4.1.7 | PerfIntervalCount64 | read-only | The counter associated with the interval number of packets with CRC errors, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpErrCntIntRingRxGiantPkts | 1.3.6.1.4.1.9.10.60.4.4.1.5 | PerfIntervalCount64 | read-only | The counter associated with the interval number of giant packets, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpErrCntIntRingRxShortPkts | 1.3.6.1.4.1.9.10.60.4.4.1.4 | PerfIntervalCount64 | read-only | The counter associated with the interval number of short packets, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpErrCntIntRingRxTtlExpPkts | 1.3.6.1.4.1.9.10.60.4.4.1.3 | PerfIntervalCount64 | read-only | The counter associated with the interval number of expired packets, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| srpErrCntIntTable | 1.3.6.1.4.1.9.10.60.4.4 | not-accessible | The SRP Errors Interval counters table. | |
| srpErrorsCounters | 1.3.6.1.4.1.9.10.60.4 | |||
| srpErrorsCountersCurrentEntry | 1.3.6.1.4.1.9.10.60.4.1.1 | not-accessible | Errors statistics for the current interval of a particular side of a particular SRP interface. The corresponding instance of srpIfTimeElapsed indicates the number of seconds which have elapsed so far in the current interval. | |
| srpErrorsCountersCurrentGroup | 1.3.6.1.4.1.9.10.60.6.1.9 | A collection of objects providing information about errors coming from the ring to a particular node in the current 15 minute interval. | ||
| srpErrorsCountersCurrentTable | 1.3.6.1.4.1.9.10.60.4.1 | not-accessible | The SRP Errors Current counters table. | |
| srpErrorsCountersIntervalEntry | 1.3.6.1.4.1.9.10.60.4.2.1 | not-accessible | Error statistics collected for a particular interval of a particular side of a particular SRP interface. The number of 15-minute intervals is between 1 and 96, and identifies the intervals for which the set of statistics is available. | |
| srpErrorsCountersIntervalGroup | 1.3.6.1.4.1.9.10.60.6.1.10 | A collection of objects providing information about errors coming from the higher layer to a particular interface in the current 15 minute interval. | ||
| srpErrorsCountersIntervalTable | 1.3.6.1.4.1.9.10.60.4.2 | not-accessible | The SRP Errors Interval counters table. | |
| NUM srpErrorsInterfaceSide | 1.3.6.1.4.1.9.10.60.4.1.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| NUM srpErrorsIntervalInterfaceSide | 1.3.6.1.4.1.9.10.60.4.2.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| I32 srpErrorsIntervalNumber | 1.3.6.1.4.1.9.10.60.4.2.1.2 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set od statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and interval identified by N is the interval immediately preceding the one identified by N-1. |
| srpGroups | 1.3.6.1.4.1.9.10.60.6.1 | |||
| srpHostCounters | 1.3.6.1.4.1.9.10.60.3 | |||
| srpHostCountersCurrentEntry | 1.3.6.1.4.1.9.10.60.3.1.1 | not-accessible | Packets and octets statistics for the current interval for the Higher Layer of a particular side of a particular SRP interface. The corresponding instance of srpIfTimeElapsed indicates the number of seconds which have elapsed so far in the current interval. | |
| srpHostCountersCurrentGroup | 1.3.6.1.4.1.9.10.60.6.1.7 | A collection of objects providing information about uni or multicast packets and octets coming from the host to a particular node in the current 15 minute interval. | ||
| srpHostCountersCurrentTable | 1.3.6.1.4.1.9.10.60.3.1 | not-accessible | The Higher Layer Current counters table. | |
| srpHostCountersIntervalEntry | 1.3.6.1.4.1.9.10.60.3.2.1 | not-accessible | Packets and octets statistics collected for a particular interval for the Higher Layer of a particular side of a particular SRP interface. The number of 15-minute intervals is between 1 and 96, and identifies the intervals for which the set of statistics is available. | |
| srpHostCountersIntervalGroup | 1.3.6.1.4.1.9.10.60.6.1.8 | A collection of objects providing information about uni or multicast packets and octets coming from the host to a particular node in a particular 15-minute interval in the past 24 hours. | ||
| srpHostCountersIntervalTable | 1.3.6.1.4.1.9.10.60.3.2 | not-accessible | The Higher Layer Interval counters table. | |
| PER srpHostCurMcastHighPriOctetsIn | 1.3.6.1.4.1.9.10.60.3.1.1.9 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority multicast octets received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurMcastHighPriOctetsOut | 1.3.6.1.4.1.9.10.60.3.1.1.17 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority multicast octets going to the Higher Layer in the current 15 minute interval. |
| PER srpHostCurMcastHighPriPktsIn | 1.3.6.1.4.1.9.10.60.3.1.1.8 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority multicast packets received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurMcastHighPriPktsOut | 1.3.6.1.4.1.9.10.60.3.1.1.16 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority multicast packets going to the Higher Layer in the current 15 minute interval. |
| PER srpHostCurMcastLowPriOctetsIn | 1.3.6.1.4.1.9.10.60.3.1.1.5 | PerfCurrentCount64 | read-only | The counter associated with the number of total multicast octets received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurMcastLowPriOctetsOut | 1.3.6.1.4.1.9.10.60.3.1.1.13 | PerfCurrentCount64 | read-only | The counter associated with the number of total multicast octets going to the Higher Layer in the current 15 minute interval. |
| PER srpHostCurMcastLowPriPktsIn | 1.3.6.1.4.1.9.10.60.3.1.1.4 | PerfCurrentCount64 | read-only | The counter associated with the number of total multicast packets received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurMcastLowPriPktsOut | 1.3.6.1.4.1.9.10.60.3.1.1.12 | PerfCurrentCount64 | read-only | The counter associated with the number of total multicast packets going to the Higher Layer in the current 15 minute interval. |
| PER srpHostCurRxErrorsDataParity | 1.3.6.1.4.1.9.10.60.4.1.1.7 | PerfCurrentCount64 | read-only | The counter associated with the current number of data parity errors, received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurRxErrorsGiantPackets | 1.3.6.1.4.1.9.10.60.4.1.1.9 | PerfCurrentCount64 | read-only | The counter associated with the current number of giant packets, received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurRxErrorsShortPackets | 1.3.6.1.4.1.9.10.60.4.1.1.8 | PerfCurrentCount64 | read-only | The counter associated with the current number of short packets, received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurRxErrorsSideBadPackets | 1.3.6.1.4.1.9.10.60.4.1.1.10 | PerfCurrentCount64 | read-only | The counter associated with the current number of bad packets, received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurUcastHighPriOctetsIn | 1.3.6.1.4.1.9.10.60.3.1.1.7 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority unicast octets received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurUcastHighPriOctetsOut | 1.3.6.1.4.1.9.10.60.3.1.1.15 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority unicast octets going to from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurUcastHighPriPktsIn | 1.3.6.1.4.1.9.10.60.3.1.1.6 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority unicast packets received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurUcastHighPriPktsOut | 1.3.6.1.4.1.9.10.60.3.1.1.14 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority unicast packets going to the Higher Layer in the current 15 minute interval. |
| PER srpHostCurUcastLowPriOctetsIn | 1.3.6.1.4.1.9.10.60.3.1.1.3 | PerfCurrentCount64 | read-only | The counter associated with the number of total unicast octets received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurUcastLowPriOctetsOut | 1.3.6.1.4.1.9.10.60.3.1.1.11 | PerfCurrentCount64 | read-only | The counter associated with the number of total unicast octets going to the Higher Layer in the current 15 minute interval. |
| PER srpHostCurUcastLowPriPktsIn | 1.3.6.1.4.1.9.10.60.3.1.1.2 | PerfCurrentCount64 | read-only | The counter associated with the number of total unicast packets received from the Higher Layer in the current 15 minute interval. |
| PER srpHostCurUcastLowPriPktsOut | 1.3.6.1.4.1.9.10.60.3.1.1.10 | PerfCurrentCount64 | read-only | The counter associated with the number of total unicast packets going to the Higher Layer in the current 15 minute interval. |
| NUM srpHostInterfaceSide | 1.3.6.1.4.1.9.10.60.3.1.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| NUM srpHostIntInterfaceSide | 1.3.6.1.4.1.9.10.60.3.2.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| NUM srpHostIntMcastHighPriOctetsIn | 1.3.6.1.4.1.9.10.60.3.2.1.10 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority multicast octets received from the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntMcastHighPriOctetsOut | 1.3.6.1.4.1.9.10.60.3.2.1.18 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority multicast octets going to the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntMcastHighPriPktsIn | 1.3.6.1.4.1.9.10.60.3.2.1.9 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority multicast packets received from the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntMcastHighPriPktsOut | 1.3.6.1.4.1.9.10.60.3.2.1.17 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority multicast packets going to the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntMcastLowPriOctetsIn | 1.3.6.1.4.1.9.10.60.3.2.1.6 | PerfIntervalCount64 | read-only | The counter associated with the number of total multicast octets received from the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntMcastLowPriOctetsOut | 1.3.6.1.4.1.9.10.60.3.2.1.14 | PerfIntervalCount64 | read-only | The counter associated with the number of total multicast octets going to the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntMcastLowPriPktsIn | 1.3.6.1.4.1.9.10.60.3.2.1.5 | PerfIntervalCount64 | read-only | The counter associated with the number of total multicast packets received from the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntMcastLowPriPktsOut | 1.3.6.1.4.1.9.10.60.3.2.1.13 | PerfIntervalCount64 | read-only | The counter associated with the number of total multicast packets going to the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| I32 srpHostIntNumber | 1.3.6.1.4.1.9.10.60.3.2.1.2 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set od statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM srpHostIntRxErrorsDataParity | 1.3.6.1.4.1.9.10.60.4.2.1.8 | PerfIntervalCount64 | read-only | The counter associated with the interval number of data parity errors, received from the higher layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntRxErrorsGiantPackets | 1.3.6.1.4.1.9.10.60.4.2.1.10 | PerfIntervalCount64 | read-only | The counter associated with the interval number of giant packets, received from the higher layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntRxErrorsShortPackets | 1.3.6.1.4.1.9.10.60.4.2.1.9 | PerfIntervalCount64 | read-only | The counter associated with the interval number of short packets, received from the higher layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntRxErrorsSideBadPackets | 1.3.6.1.4.1.9.10.60.4.2.1.11 | PerfIntervalCount64 | read-only | The counter associated with the interval number of bad packets, received from the higher layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntUcastHighPriOctetsIn | 1.3.6.1.4.1.9.10.60.3.2.1.8 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority unicast octets received from from the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntUcastHighPriOctetsOut | 1.3.6.1.4.1.9.10.60.3.2.1.16 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority unicast octets going to the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntUcastHighPriPktsIn | 1.3.6.1.4.1.9.10.60.3.2.1.7 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority unicast packets received from the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntUcastHighPriPktsOut | 1.3.6.1.4.1.9.10.60.3.2.1.15 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority unicast packets going to the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntUcastLowPriOctetsIn | 1.3.6.1.4.1.9.10.60.3.2.1.4 | PerfIntervalCount64 | read-only | The counter associated with the number of total unicast octets received from the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntUcastLowPriOctetsOut | 1.3.6.1.4.1.9.10.60.3.2.1.12 | PerfIntervalCount64 | read-only | The counter associated with the number of total unicast octets going to the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntUcastLowPriPktsIn | 1.3.6.1.4.1.9.10.60.3.2.1.3 | PerfIntervalCount64 | read-only | The counter associated with the number of total unicast packets received from the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpHostIntUcastLowPriPktsOut | 1.3.6.1.4.1.9.10.60.3.2.1.11 | PerfIntervalCount64 | read-only | The counter associated with the number of total unicast packets going to the Higher Layer in a particular 15-minute interval in the past 24 hours. |
| srpIfEntry | 1.3.6.1.4.1.9.10.60.1.1.1 | not-accessible | There exists one such entry for every interface in the ifTable which has an ifType of SRP interface (151) Each of these entries are indexed by the value of ifIndex as defined in RFC2233. | |
| srpIfGroup | 1.3.6.1.4.1.9.10.60.6.1.1 | A collection of objects providing information independent from a particular side A or B and is applicable to all SRP interfaces. | ||
| srpIfTable | 1.3.6.1.4.1.9.10.60.1.1 | not-accessible | The SRP interface table. | |
| I32 srpIfTimeElapsed | 1.3.6.1.4.1.9.10.60.1.1.1.7 | Integer32 | read-only | The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement interval as described in RFC 2493. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| I32 srpIfValidIntervals | 1.3.6.1.4.1.9.10.60.1.1.1.8 | Integer32 | read-only | The number of previous 15-minute measurement intervals for which data was collected. A SRP interface must be capable of supporting at least n intervals. The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available. |
| T/F srpIpsLockedOut | 1.3.6.1.4.1.9.10.60.1.1.1.5 | TruthValue | read-write | The boolean flag to indicate node LockedOut of protection state. If it's true than Intelligent Protection Swiching is disabled and the node will not wrap on either side of the interface. |
| INT srpIpsState | 1.3.6.1.4.1.9.10.60.1.1.1.4 | INTEGER | read-only | Each node in the Intelligent Protection Switching (IPS) is one of the following states. Idle - In this mode the node is ready to perform protection and it sends to both neighboring nodes idle IPS messages, which include self in the source address field {0, SELF, 0, S}. PassThrough - Node participate in a protection switch by passing the wrapped traffic and long path signalling through itself. This state is entered based on received IPS messages. Wrapped - Node participate in a protection switch with a wrap present. This state is entered based on protection request issued locally or based on received IPS messages. When interface is down the value for IPS state is passThrough. |
| I32 srpIpsWaitToRestoreTimer | 1.3.6.1.4.1.9.10.60.1.1.1.6 | Integer32 | read-write | Indicates the length of time in seconds, to remain in the wrap state, after the cause of a wrap is removed. This mechanism prevents protection switch oscillations. Default value is 60 sec. |
| srpMAC | 1.3.6.1.4.1.9.10.60.1 | |||
| MAC srpMACAddress | 1.3.6.1.4.1.9.10.60.1.1.1.1 | MacAddress | read-only | The MAC's 48-bit individual MAC address. |
| INT srpMACClockSourceMode | 1.3.6.1.4.1.9.10.60.1.2.1.12 | INTEGER | read-write | Indicates the mode of the SRP interface clock source. Internal - mode specifies the clock source as internal, and is used when connecting between two routers over a dark fiber or over WDM system. The internal mode is used as a default value. Line - mode specifies the clock source as line, and is used when connecting a router to SONET/SDH ADM. |
| srpMACCountersEntry | 1.3.6.1.4.1.9.10.60.1.6.1 | not-accessible | A packet counting and packet reject capability for a source and/or destination address on a particular SRP interface. | |
| srpMACCountersGroup | 1.3.6.1.4.1.9.10.60.6.1.4 | A collection of objects providing information about packets received or rejected by a particular source or destination address. | ||
| srpMACCountersTable | 1.3.6.1.4.1.9.10.60.1.6 | not-accessible | The MAC layer traffic Counters table. | |
| C64 srpMACCountPktsByDest | 1.3.6.1.4.1.9.10.60.1.6.1.8 | Counter64 | read-only | Counter for the number of packets send to a particular destination node's MAC address. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of srpMACDestDiscontTimeStamp. |
| MAC srpMACCountPktsByDestAddress | 1.3.6.1.4.1.9.10.60.1.6.1.6 | MacAddress | read-write | Indicates the particular destination address for which packets are to be counted when the corresponding instance of srpMACCountPktsByDestinationFlag has the value 'true'. |
| T/F srpMACCountPktsByDestinationFlag | 1.3.6.1.4.1.9.10.60.1.6.1.5 | TruthValue | read-write | Indicates that packets are to be counted for a particular destination address. |
| C64 srpMACCountPktsBySource | 1.3.6.1.4.1.9.10.60.1.6.1.4 | Counter64 | read-only | Counter for the number of packets received from a particular source node's MAC address. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of srpMACSourceDiscontTimeStamp. |
| MAC srpMACCountPktsBySourceAddress | 1.3.6.1.4.1.9.10.60.1.6.1.2 | MacAddress | read-write | Indicates the particular source address for which packets are to be counted when the corresponding instance of srpMACCountPktsBySourceFlag has the value 'true'. |
| T/F srpMACCountPktsBySourceFlag | 1.3.6.1.4.1.9.10.60.1.6.1.1 | TruthValue | read-write | Indicates that packets are to be counted for a particular source address. |
| TIM srpMACDestDiscontTimeStamp | 1.3.6.1.4.1.9.10.60.1.6.1.7 | TimeStamp | read-only | The value of sysUpTime on the most recent occasion when there was a change in the value of the corresponding instances of either srpMACCountPktsByDestAddress or srpMACCountPktsByDestinationFlag. |
| NUM srpMACInterfaceSide | 1.3.6.1.4.1.9.10.60.1.2.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| IPS srpMACIpsActiveMode | 1.3.6.1.4.1.9.10.60.1.2.1.8 | IpsMode | read-only | The currently active IPS mode for the local node, which can be changed based on combined effect of the following variables: srpMACIpsMgmtRequestedMode, srpMACIpsAutoDetectMode, srpMACIpsRemoteMode, and srpMACIpsRemoteType according to the set of rules describing IPS protocol. |
| IPS srpMACIpsAutoDetectMode | 1.3.6.1.4.1.9.10.60.1.2.1.5 | IpsMode | read-only | The current IPS mode as automatically detected by the the local node that can affect the srpMACIpsActiveMode state of the SRP node, according to the set of rules describing IPS protocol. This variable value is one from the following subset (SignalFail, SignalDegrade, WaitToRestore). |
| TIM srpMACIpsLastUnWrapTimeStamp | 1.3.6.1.4.1.9.10.60.1.2.1.11 | TimeStamp | read-only | The value of sysUpTime for the last unwrap. |
| TIM srpMACIpsLastWrapTimeStamp | 1.3.6.1.4.1.9.10.60.1.2.1.10 | TimeStamp | read-only | The value of sysUpTime for the last wrap. |
| IPS srpMACIpsMgmtRequestedMode | 1.3.6.1.4.1.9.10.60.1.2.1.4 | IpsMode | read-write | The IPS mode requested by management for the local node that can affect the srpMACIpsActiveMode state of the SRP node, according to the set of rules describing IPS protocol. This variable value is one from the following subset (noRequest, manualSwitch, forcedSwitch). |
| IPS srpMACIpsRemoteMode | 1.3.6.1.4.1.9.10.60.1.2.1.6 | IpsMode | read-only | The IPS mode indicated in IPS messages being received by the local node from other nodes on the ring, that can affect the srpMACIpsActiveMode state of the SRP node, according to the set of rules describing IPS protocol. |
| INT srpMACIpsRemoteType | 1.3.6.1.4.1.9.10.60.1.2.1.7 | INTEGER | read-only | Indicates if srpMACIpsRemoteMode object value belongs to the adjacent node in the case of the shortPath or belongs to the non-adjacent node in the case of the longPath. |
| C32 srpMACIpsWrapCounterEx | 1.3.6.1.4.1.9.10.60.1.2.1.9 | Counter32 | read-only | The number of transition from unwrap to wrap state. |
| MAC srpMACNeighborAddress | 1.3.6.1.4.1.9.10.60.1.2.1.2 | MacAddress | read-only | The MAC's neighbor's 48-bit individual MAC address. |
| MAC srpMACRejectPktsByDestAddress | 1.3.6.1.4.1.9.10.60.1.6.1.12 | MacAddress | read-write | Indicates the particular destination address for which packets are to rejected when the corresponding instance of srpMACRejectPktsByDestFlag has the value 'true'. |
| T/F srpMACRejectPktsByDestFlag | 1.3.6.1.4.1.9.10.60.1.6.1.11 | TruthValue | read-write | Indicates that packets are to be rejected for a particular destination address. |
| MAC srpMACRejectPktsBySourceAddress | 1.3.6.1.4.1.9.10.60.1.6.1.10 | MacAddress | read-write | Indicates the particular source address for which packets are to rejected when the corresponding instance of srpMACRejectPktsBySourceFlag has the value 'true'. |
| T/F srpMACRejectPktsBySourceFlag | 1.3.6.1.4.1.9.10.60.1.6.1.9 | TruthValue | read-write | Indicates that packets are to be rejected for a particular source address. |
| srpMACSideEntry | 1.3.6.1.4.1.9.10.60.1.2.1 | not-accessible | A list of information specific to a particular side of a particular SRP interface. | |
| srpMACSideGroup | 1.3.6.1.4.1.9.10.60.6.1.2 | A collection of objects providing information dependent from a particular side A or B and is specific to MAC and IPS (Intelligent protection Switching). | ||
| srpMACSideTable | 1.3.6.1.4.1.9.10.60.1.2 | not-accessible | A table of information about the sides of SRP interfaces. | |
| T/F srpMACSideWrapped | 1.3.6.1.4.1.9.10.60.1.2.1.3 | TruthValue | read-only | The boolean flag to indicate the node's wrapped state. |
| TIM srpMACSourceDiscontTimeStamp | 1.3.6.1.4.1.9.10.60.1.6.1.3 | TimeStamp | read-only | The value of sysUpTime on the most recent occasion when there was a change in the value of the corresponding instances of either srpMACCountPktsBySourceAddress or srpMACCountPktsBySourceFlag. |
| I32 srpMACTopologyTimer | 1.3.6.1.4.1.9.10.60.1.2.1.13 | Integer32 | read-write | Indicates the topology-timer on a SRP ring, how frequently topology discovery messages are sent around ring to identify the nodes. Toplogy discovery is always on. The default value is 10 seconds. |
| U32 srpNodeHopsNumber | 1.3.6.1.4.1.9.10.60.1.3.1.1 | Unsigned32 | not-accessible | A value, between 0 and (srpNodesOnTheRing - 1), used to identify the particular node which is the number of hops around the ring (clock-wise) away from the local node. |
| MAC srpNodeMACAddress | 1.3.6.1.4.1.9.10.60.1.3.1.2 | MacAddress | read-only | The node MAC's 48-bit individual MAC address. |
| STR srpNodeName | 1.3.6.1.4.1.9.10.60.1.3.1.4 | DisplayString | read-only | The node name reported by the SRP protocol. If the name is not known then this field is left blank. |
| I32 srpNodesOnTheRing | 1.3.6.1.4.1.9.10.60.1.1.1.3 | Integer32 | read-only | The number of nodes in the SRP ring. When interface is down the value is 0. |
| T/F srpNodeWrapped | 1.3.6.1.4.1.9.10.60.1.3.1.3 | TruthValue | read-only | Indicates in general if the node is wrapped without specifying on which side. |
| srpNotificationsGroup | 1.3.6.1.4.1.9.10.60.6.1.13 | The collection of notifications used to indicate wrapped and unwrapped node state information. | ||
| I32 srpPriorityThreshold | 1.3.6.1.4.1.9.10.60.1.1.1.2 | Integer32 | read-write | The priority threshold value to be compared against the 3 bits of priority contained in each packet's SRP header. If a packet's priority is greater or equal to this threshold, that packet should be placed in the high priority transmit or transit queue. If a packet's priority is less than this threshold, it should be placed in the low priority transmit or transit queue. Since there are only two types of priority queues (High Priority and Low Priority) a packet is treated as either low or high priority once it is on the ring. Each node determines the threshold value for classifying what is considered a high priority packet and what is considered a low priority packet. |
| srpRingCounters | 1.3.6.1.4.1.9.10.60.2 | |||
| srpRingCountersCurrentEntry | 1.3.6.1.4.1.9.10.60.2.1.1 | not-accessible | Packets and octets statistics for the current interval for the Physical medium dependent layer of a particular side of a particular SRP interface. The corresponding instance of srpIfTimeElapsed indicates the number of seconds which have elapsed so far in the current interval. | |
| srpRingCountersCurrentGroup | 1.3.6.1.4.1.9.10.60.6.1.5 | A collection of objects providing information about unicast or multicast packets and octets coming from the ring to a particular node in the current 15 minute interval. | ||
| srpRingCountersCurrentTable | 1.3.6.1.4.1.9.10.60.2.1 | not-accessible | The Physical medium dependent layer Current counters table. | |
| srpRingCountersIntervalEntry | 1.3.6.1.4.1.9.10.60.2.2.1 | not-accessible | Packets and octets statistics collected for a particular interval for the Physical medium dependent layer of a particular side of a particular SRP interface. The number of 15-minute intervals is between 1 and 96, identifies the intervals for which the set of and statistics is available. | |
| srpRingCountersIntervalGroup | 1.3.6.1.4.1.9.10.60.6.1.6 | A collection of objects providing information about uni or multicast packets and octets coming from the ring to a particular node in a particular 15-minute interval in the past 24 hours. | ||
| srpRingCountersIntervalTable | 1.3.6.1.4.1.9.10.60.2.2 | not-accessible | The Physical medium dependent layer Interval counters table. | |
| PER srpRingCurMcastHighPriOctetsIn | 1.3.6.1.4.1.9.10.60.2.1.1.9 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority multicast octets received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurMcastHighPriOctetsOut | 1.3.6.1.4.1.9.10.60.2.1.1.17 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority multicast octets going to the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurMcastHighPriPktsIn | 1.3.6.1.4.1.9.10.60.2.1.1.8 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority multicast packets received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurMcastHighPriPktsOut | 1.3.6.1.4.1.9.10.60.2.1.1.16 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority multicast packets going to the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurMcastLowPriOctetsIn | 1.3.6.1.4.1.9.10.60.2.1.1.5 | PerfCurrentCount64 | read-only | The counter associated with the number of low priority multicast octets received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurMcastLowPriOctetsOut | 1.3.6.1.4.1.9.10.60.2.1.1.13 | PerfCurrentCount64 | read-only | The counter associated with the number of low priority multicast octets going to the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurMcastLowPriPktsIn | 1.3.6.1.4.1.9.10.60.2.1.1.4 | PerfCurrentCount64 | read-only | The counter associated with the number of low priority multicast packets received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurMcastLowPriPktsOut | 1.3.6.1.4.1.9.10.60.2.1.1.12 | PerfCurrentCount64 | read-only | The counter associated with the number of low priority multicast packets going to the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurRxErrorsCRC | 1.3.6.1.4.1.9.10.60.4.1.1.6 | PerfCurrentCount64 | read-only | The counter associated with the current number of packets with CRC errors, received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurRxErrorsDataParity | 1.3.6.1.4.1.9.10.60.4.1.1.2 | PerfCurrentCount64 | read-only | The counter associated with the number of data parity errors, received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurRxErrorsGiantPackets | 1.3.6.1.4.1.9.10.60.4.1.1.4 | PerfCurrentCount64 | read-only | The counter associated with the number of giant packets, received from the Physical medium dependent layer in the current 15 minute interval. A giant packet is larger than max size MTU, which is 9216 octets. |
| PER srpRingCurRxErrorsShortPackets | 1.3.6.1.4.1.9.10.60.4.1.1.3 | PerfCurrentCount64 | read-only | The counter associated with the number of short packets, received from the Physical medium dependent layer in the current 15 minute interval. A short packet is 16 octets or less. |
| PER srpRingCurRxErrorsSideBadPackets | 1.3.6.1.4.1.9.10.60.4.1.1.5 | PerfCurrentCount64 | read-only | The counter associated with the current number of bad packets, received from the Physical medium dependent layer in the current 15 minute interval. A bad packet is an empty packet with a valid Start-Of-Packet signal causing an incorrect CRC. |
| PER srpRingCurUcastHighPriOctetsIn | 1.3.6.1.4.1.9.10.60.2.1.1.7 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority unicast octets received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurUcastHighPriOctetsOut | 1.3.6.1.4.1.9.10.60.2.1.1.15 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority unicast octets going to the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurUcastHighPriPktsIn | 1.3.6.1.4.1.9.10.60.2.1.1.6 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority unicast packets received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurUcastHighPriPktsOut | 1.3.6.1.4.1.9.10.60.2.1.1.14 | PerfCurrentCount64 | read-only | The counter associated with the number of high priority unicast packets going to the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurUcastLowPriOctetsIn | 1.3.6.1.4.1.9.10.60.2.1.1.3 | PerfCurrentCount64 | read-only | The counter associated with the number of low priority unicast octets received from the Physical medium dependent layer in the current 15minute interval. |
| PER srpRingCurUcastLowPriOctetsOut | 1.3.6.1.4.1.9.10.60.2.1.1.11 | PerfCurrentCount64 | read-only | The counter associated with the number of low priority unicast octets going to the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurUcastLowPriPktsIn | 1.3.6.1.4.1.9.10.60.2.1.1.2 | PerfCurrentCount64 | read-only | The counter associated with the number of low priority unicast packets received from the Physical medium dependent layer in the current 15 minute interval. |
| PER srpRingCurUcastLowPriPktsOut | 1.3.6.1.4.1.9.10.60.2.1.1.10 | PerfCurrentCount64 | read-only | The counter associated with the number of low priority unicast packets going to the Physical medium dependent layer in the current 15 minute interval. |
| NUM srpRingInterfaceSide | 1.3.6.1.4.1.9.10.60.2.1.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| NUM srpRingIntInterfaceSide | 1.3.6.1.4.1.9.10.60.2.2.1.1 | InterfaceSide | not-accessible | An indication of the side of the interface for which this row contains information. |
| NUM srpRingIntMcastHighPriOctetsIn | 1.3.6.1.4.1.9.10.60.2.2.1.11 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority multicast octets received from the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntMcastHighPriOctetsOut | 1.3.6.1.4.1.9.10.60.2.2.1.19 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority multicast octets going to the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntMcastHighPriPktsIn | 1.3.6.1.4.1.9.10.60.2.2.1.10 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority multicast packets received from the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntMcastHighPriPktsOut | 1.3.6.1.4.1.9.10.60.2.2.1.18 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority multicast packets going to the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntMcastLowPriOctetsIn | 1.3.6.1.4.1.9.10.60.2.2.1.7 | PerfIntervalCount64 | read-only | The counter associated with the number of low priority multicast octets received from the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntMcastLowPriOctetsOut | 1.3.6.1.4.1.9.10.60.2.2.1.15 | PerfIntervalCount64 | read-only | The counter associated with the number of low priority multicast octets going to the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntMcastLowPriPktsIn | 1.3.6.1.4.1.9.10.60.2.2.1.6 | PerfIntervalCount64 | read-only | The counter associated with the number of low priority multicast packets received from the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntMcastLowPriPktsOut | 1.3.6.1.4.1.9.10.60.2.2.1.14 | PerfIntervalCount64 | read-only | The counter associated with the number of low priority multicast packets going to the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| I32 srpRingIntNumber | 1.3.6.1.4.1.9.10.60.2.2.1.2 | Integer32 | not-accessible | A number between 1 and 96, which identifies the intervals for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM srpRingIntRxErrorsCRC | 1.3.6.1.4.1.9.10.60.4.2.1.7 | PerfIntervalCount64 | read-only | The counter associated with the interval number of packets with CRC errors, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntRxErrorsDataParity | 1.3.6.1.4.1.9.10.60.4.2.1.3 | PerfIntervalCount64 | read-only | The counter associated with the interval number of data parity errors, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntRxErrorsGiantPackets | 1.3.6.1.4.1.9.10.60.4.2.1.5 | PerfIntervalCount64 | read-only | The counter associated with the interval number of giant packets, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntRxErrorsShortPackets | 1.3.6.1.4.1.9.10.60.4.2.1.4 | PerfIntervalCount64 | read-only | The counter associated with the interval number of short packets, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntRxErrorsSideBadPackets | 1.3.6.1.4.1.9.10.60.4.2.1.6 | PerfIntervalCount64 | read-only | The counter associated with the interval number of bad packets, received from the Layer 1 Physical medium in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntUcastHighPriOctetsIn | 1.3.6.1.4.1.9.10.60.2.2.1.9 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority unicast octets received from the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntUcastHighPriOctetsOut | 1.3.6.1.4.1.9.10.60.2.2.1.17 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority unicast octets going to the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntUcastHighPriPktsIn | 1.3.6.1.4.1.9.10.60.2.2.1.8 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority unicast packets received from the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntUcastHighPriPktsOut | 1.3.6.1.4.1.9.10.60.2.2.1.16 | PerfIntervalCount64 | read-only | The counter associated with the number of high priority unicast packets going to the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntUcastLowPriOctetsIn | 1.3.6.1.4.1.9.10.60.2.2.1.5 | PerfIntervalCount64 | read-only | The counter associated with the number of low priority unicast octets received from the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntUcastLowPriOctetsOut | 1.3.6.1.4.1.9.10.60.2.2.1.13 | PerfIntervalCount64 | read-only | The counter associated with the number of low priority unicast octets going to the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntUcastLowPriPktsIn | 1.3.6.1.4.1.9.10.60.2.2.1.4 | PerfIntervalCount64 | read-only | The counter associated with the number of low priority unicast packets received from the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| NUM srpRingIntUcastLowPriPktsOut | 1.3.6.1.4.1.9.10.60.2.2.1.12 | PerfIntervalCount64 | read-only | The counter associated with the number of low priority unicast packets going to the Physical medium dependent layer in a particular 15-minute interval in the past 24 hours. |
| C32 srpRingIntWrapCounter | 1.3.6.1.4.1.9.10.60.2.2.1.3 | Counter32 | read-only | The counter counts the number of transition from unwrap to wrap state for the last intervals described by the srpRingIntNumber variable. |
| srpRingTopologyMapEntry | 1.3.6.1.4.1.9.10.60.1.3.1 | not-accessible | A MAC entry containing information specific to a particular node on the ring. | |
| srpRingTopologyMapGroup | 1.3.6.1.4.1.9.10.60.6.1.3 | A collection of objects providing information on the ring topology and nodes status. | ||
| srpRingTopologyMapTable | 1.3.6.1.4.1.9.10.60.1.3 | not-accessible | A list of SRP ring topology map entries. | |
| NTF srpTrapRingRestored | 1.3.6.1.4.1.9.10.60.5.0.2 | An srpTrapRingRestored notification is sent when the value of an instance of rpMACIpsLastUnWrapTimeStamp is changed. | ||
| NTF srpTrapRingWrapped | 1.3.6.1.4.1.9.10.60.5.0.1 | An srpTrapRingWrapped notification is sent when the value of an instance of srpMACIpsWrapCounter increments. | ||
| srpTrapsNotifications | 1.3.6.1.4.1.9.10.60.5.0 | |||
| srpTrapsNotificationsPrefix | 1.3.6.1.4.1.9.10.60.5 |
RFC description
Manages Spatial Reuse Protocol (SRP) interface layer for Cisco dual-ring fiber networks including error counters and performance metrics.
Start monitoring Cisco DPT/SRP ring interface routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.