CISCO-SRP-MIB :: srpHostIntUcastLowPriOctetsIn

MIB Reference — IPNetwork Monitor · Updated September 14, 2026

All MIBsCISCO-SRP-MIBsrpHostIntUcastLowPriOctetsIn

srpHostIntUcastLowPriOctetsIn

Module: CISCO-SRP-MIB

OID (symbolic): CISCO-SRP-MIB::srpHostIntUcastLowPriOctetsIn

OID (numeric): 1.3.6.1.4.1.9.10.60.3.2.1.4

Node type: OBJECT-TYPE

Type: PerfIntervalCount64

Access: read-only

Description: The counter associated with the number of total unicast octets received from the Higher Layer in a particular 15-minute interval in the past 24 hours.

What is srpHostIntUcastLowPriOctetsIn?

This is a 64-bit counter of unicast bytes (octet count) delivered up from the ring into the router's own higher-layer stack, labeled by its real description simply as the 'total' count rather than explicitly 'low priority' (even though the object's own name says LowPri), measured over one specific, already-completed 15-minute bucket from the rolling 24-hour history, rather than a live count. Because this is measured on the host side, it reflects only traffic this specific router is locally sourcing or sinking, so comparing it against the Ring-side counters on the same box shows how much of what crosses the ring this node actually originates versus just passes through, because SRP always drains high-priority traffic first, a plateau or drop in this low-priority counter while the matching high-priority counter is climbing indicates best-effort traffic is being squeezed out by real-time/control traffic rather than genuinely dropping off, with unicast traffic being the more direct proxy for ordinary point-to-point application load between specific ring nodes, and pairing this byte count with the matching packet counter for the same traffic class is how you'd derive the average frame size and the actual bit rate that class is consuming. For instance, this counter might read roughly 776,902,742 bytes of unicast traffic over that window, which combined with the matching packet counter lets you compute an average frame size for that class.

Examples

Walk all instances (SNMPv2c):

snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.60.3.2.1.4
snmpwalk -v2c -c public <target> CISCO-SRP-MIB::srpHostIntUcastLowPriOctetsIn

Get a specific instance (index 1):

snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.60.3.2.1.4.1
snmpget -v2c -c public <target> CISCO-SRP-MIB::srpHostIntUcastLowPriOctetsIn.1

Start monitoring Cisco DPT/SRP ring interface routers with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-SRP-MIB::srpHostIntUcastLowPriOctetsIn OID value, configure state conditions and alerts, and monitor any Cisco DPT/SRP ring interface routers from a single console.

OID Breakdown

Upper-level ancestors (8 from the standard OID tree / other modules)
Numeric OIDNameModule
1isoLANART-AGENT
1.3orgAirPair-MIB
1.3.6dodAirPair-MIB
1.3.6.1internetAirPair-MIB
1.3.6.1.4privateAirPair-MIB
1.3.6.1.4.1enterprisesAirPair-MIB
1.3.6.1.4.1.9ciscoCAT2600-MIB
1.3.6.1.4.1.9.10ciscoExperimentCISCO-SMI
Numeric OIDNameModule
1.3.6.1.4.1.9.10.60ciscosrpMIBCISCO-SRP-MIB
1.3.6.1.4.1.9.10.60.3srpHostCountersCISCO-SRP-MIB
1.3.6.1.4.1.9.10.60.3.2srpHostCountersIntervalTableCISCO-SRP-MIB
1.3.6.1.4.1.9.10.60.3.2.1srpHostCountersIntervalEntryCISCO-SRP-MIB
1.3.6.1.4.1.9.10.60.3.2.1.4srpHostIntUcastLowPriOctetsInCISCO-SRP-MIB