All MIBs › CISCO-WIRELESS-P2MP-PHY-MIB
Organization: Cisco Systems Inc.
Last Updated: 2000-10-22
Category: Vendor: Cisco Devices, Wireless and WLAN
Description: Manages Cisco wireless P2MP physical layer configuration including modulation and frequency settings.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-WIRELESS-P2MP-PHY-MIB?
CISCO-WIRELESS-P2MP-PHY-MIB is a Cisco MIB for the physical-layer configuration of Cisco's wireless Point-to-MultiPoint (P2MP) radio interfaces, used in fixed wireless broadband/backhaul products. It organizes objects into base radio objects, subscriber-unit (Su) radio objects, and head-end (He) radio objects, alongside groups for PHY configuration (modulation, frequency) and frequency-resource management. Its monitoring value centers on radio-link configuration and PHY-level status: administrators verify modulation scheme and frequency-channel assignment for each head-end/subscriber-unit radio, helping diagnose RF interference, mismatched modulation, or channel conflicts affecting a wireless P2MP link's throughput or stability. It depends on Cisco's broader wireless radio interface MIB conventions, ifIndex-based association, for correlating radio objects to logical interfaces. It's deployed in fixed wireless broadband access networks using Cisco P2MP radio head-end and subscriber-unit hardware, typically for last-mile connectivity. Network engineers evaluating or troubleshooting this functionality can download the CISCO-WIRELESS-P2MP-PHY-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-WIRELESS-P2MP-PHY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco wireless P2MP radio (head-end and subscriber-unit)
Monitoring Examples
An administrator would check p2mpRadioHeObjects and p2mpRadioSuObjects for the modulation and frequency settings under p2mpPhyConfigGroup on both ends of a link to confirm they match after a configuration change. A frequency or modulation mismatch between the head-end and subscriber-unit radios, visible via p2mpFreqResourceGroup, would explain a link that won't establish or shows degraded throughput. Because this module is PHY-configuration focused, it would typically be checked alongside standard interface counters for a complete link-quality picture.
What Can Be Monitored
- radio modulation configuration
- radio frequency/channel assignment
- head-end radio PHY settings
- subscriber-unit radio PHY settings
- frequency resource allocation
This MIB depends on
Related MIBs
Imported Objects
From CISCO-SMI
| ciscoMgmt | OBJECT-IDENTITY |
From CISCO-TC
| Unsigned32 |
| CwrOscState | |
| CwrRfFreqRange | |
| CwrRfType |
From ENTITY-MIB
| entPhysicalIndex | OBJECT-TYPE |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoWirelessPhyMIB | 1.3.6.1.4.1.9.9.170 | This is the MIB Module for the Cisco Wireless Radio Point to MultiPoint interface. | ||
| STR p2mpAntennaDescr | 1.3.6.1.4.1.9.9.170.1.1.2.3.1.6 | DisplayString | read-write | This object is used to describe the antenna. For example, it could be used to identify the manufacturer like in 'Manufactured by Watkins Johnson'. |
| p2mpAntennaEntry | 1.3.6.1.4.1.9.9.170.1.1.2.3.1 | not-accessible | An entry is created in this table when the managed system detects a RF resource. The entry is removed when the RF resource is removed from the wireless system. | |
| U32 p2mpAntennaGain | 1.3.6.1.4.1.9.9.170.1.1.2.3.1.7 | Unsigned32 | read-write | This object represents the receive and transmit gain of this antenna. |
| U32 p2mpAntennaIndex | 1.3.6.1.4.1.9.9.170.1.1.2.3.1.1 | Unsigned32 | not-accessible | This object, along with ifIndex, represents the index of this entry in the p2mpAntennaTable. |
| INT p2mpAntennaPolarization | 1.3.6.1.4.1.9.9.170.1.1.2.3.1.8 | INTEGER | read-only | This object represents the polarization of the antanna. |
| p2mpAntennaTable | 1.3.6.1.4.1.9.9.170.1.1.2.3 | not-accessible | This table contains information about the antennas available in the system. | |
| STR p2mpAntennaType | 1.3.6.1.4.1.9.9.170.1.1.2.3.1.5 | DisplayString | read-write | This object represents the antenna type. For example, 'dish-antenna'. |
| U32 p2mpAntennaXDim | 1.3.6.1.4.1.9.9.170.1.1.2.3.1.3 | Unsigned32 | read-write | This object represents the dimension of the antenna in the X direction. |
| U32 p2mpAntennaYDim | 1.3.6.1.4.1.9.9.170.1.1.2.3.1.4 | Unsigned32 | read-write | This object represents the dimension of the antenna in the Y direction. |
| U32 p2mpCableLoss | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.3 | Unsigned32 | read-write | This object indicates the measured signal power loss in dB due to the cable connecting the radio to the main antenna. The hardware compensates for this cable loss by adjusting the receive and transmit gain appropriately. A value of 0 indicates no degradation in the signal due to the cable. The radio hardware can compensate for a cable loss of no more than 15 db. This cable loss applies to the main antenna only. |
| U32 p2mpCableLossDiversity | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.4 | Unsigned32 | read-write | This object indicates the measured signal power loss in dB due to the cable connecting the radio to the diversity antenna. The hardware compensates for this loss by adjusting the receive and transmit gain appropriately. A value of 0 indicates no degradation in the signal due to the cable. The radio hardware can compensate for a cable loss of no more than 15 dB. This cable loss applies to the diversity antenna only. |
| T/F p2mpClockRefExt | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.6 | TruthValue | read-write | This object controls the use of external reference clock for IF module as follows: 'true(1)' - an external reference clock is used 'false(2)' - an internal reference clock is used. |
| p2mpCommonRadioGroup | 1.3.6.1.4.1.9.9.170.1.4.2.1 | Mandatory group of objects implemented to configure a point to multipoint wireless radio. | ||
| p2mpCommonRfGroup | 1.3.6.1.4.1.9.9.170.1.4.2.2 | Mandatory group of objects implemented to tune the phy quality in a point to multipoint wireless radio. | ||
| p2mpCommonTestGroup | 1.3.6.1.4.1.9.9.170.1.4.2.3 | Mandatory group of objects implemented in the point to multi point wireless system for Testing the link. | ||
| T/F p2mpCommonTrapEnable | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.7 | TruthValue | read-write | When set to true(1), the notifications common to the head end and subscriber unit are enabled. When set to false(2), these notifications are disabled. The notification controlled by this object are: - p2mpRadioPhyFailNotification - p2mpTrapRfSupplyVoltage - p2mpTrapRfRxOsc - p2mpTrapRfTxOsc - p2mpTrapRfTemp - p2mpTrapRfCommLinkError - p2mpTrapTxPower - p2mpTrapRfStatusChange |
| T/F p2mpDenyService | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.5 | TruthValue | read-only | Indicates if the service is disabled in the unit. For Head-end unit, if this object has the value of 'true', the link is in loopback mode; otherwise the link is enabled for transmitting / receiving data. For Subscriber unit, if this object has the value of 'true', the subscriber unit service is disabled; otherwise, the subscriber unit is enabled for transmitting / receiving data |
| T/F p2mpDiversityAntennaPresent | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.2 | TruthValue | read-write | When true(1), this object indicates that a diversity antenna is being used to receive the wireless transmissions. When false(2), the radio system is using a single antenna to transmit and receive. |
| STR p2mpDuplexerBurnDate | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.9 | DisplayString | read-only | This object indicates the date when the revision information was programmed into non-volatile memory. |
| p2mpDuplexerEntry | 1.3.6.1.4.1.9.9.170.1.1.2.2.1 | not-accessible | This represents one entry in the p2mpDuplexerTable. Each entry contains information about the duplexers capabilities and the associated RF resource. An entry is created in this table when the managed system detects a RF resource. The entry is removed when the RF resource is removed from the wireless system. | |
| CWR p2mpDuplexerHiPassbandMaxFreq | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.6 | CwrRfFreqRange | read-only | This object identifies the maximum frequency in the high passband that this duplexer will pass through without attenuation. |
| CWR p2mpDuplexerHiPassbandMinFreq | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.5 | CwrRfFreqRange | read-only | This object identifies the minimum frequency in the high passband that this duplexer will pass through without attenuation. |
| I32 p2mpDuplexerIndex | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.1 | Integer32 | not-accessible | This object, along with ifIndex, uniquely identifies an entry in this table. Each entry contains information about the duplexer's capabilities and also identifies the associated RF resource. |
| CWR p2mpDuplexerLoPassbandMaxFreq | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.4 | CwrRfFreqRange | read-only | This object identifies the maximum frequency in the low passband that this duplexer will pass through without attenuation. |
| CWR p2mpDuplexerLoPassbandMinFreq | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.3 | CwrRfFreqRange | read-only | This object identifies the minimum frequency in the low passband that this duplexer will pass through without attenuation. |
| INT p2mpDuplexerReceivePassband | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.7 | INTEGER | read-only | This object indicates which of the two passbands are being used to receive transmissions. The RF Resource can receive on either of the duplexer passbands. loPassband(1) - The RF Resource is receiving on a frequency in the low passband. hiPassband(2) - The RF Resource is receiving on a frequency in the high passband. |
| CWR p2mpDuplexerRF | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.2 | CwrRfType | read-only | This object identifies the RF resource associated with this duplexer. |
| p2mpDuplexerTable | 1.3.6.1.4.1.9.9.170.1.1.2.2 | not-accessible | This table contains information about the Duplexers available for use on the system. A Duplexer is a mechanical device, that acts as a band pass filter when installed in an RF resource. Normally a RF resource is capable of operating over a wide frequency range. To operate at restricted frequencies, the user has to own that part of the frequency spectrum. Since the user may not own parts of the frequency spectrum over which the RF resource may operate, a duplexer is installed at the RF. This restricts the RF resource to operate in the passband defined by the duplexer. | |
| I32 p2mpDuplexerTxInsertionLoss | 1.3.6.1.4.1.9.9.170.1.1.2.2.1.8 | Integer32 | read-only | This object represents the loss in 'dB' that would result in the transmission path due to the duplexer. |
| p2mpFreqResourceGroup | 1.3.6.1.4.1.9.9.170.1.1.2 | |||
| T/F p2mpHeAlcEnable | 1.3.6.1.4.1.9.9.170.1.3.1.1.1 | TruthValue | read-write | This object is used to enable/disable ALC at the Head End. A value of true(1), indicates that ALC is enabled. |
| p2mpHeAlcEntry | 1.3.6.1.4.1.9.9.170.1.3.1.1 | not-accessible | An entry containing the ALC configuration information the propDocsWirelessMaylayer interface at the head end. The entry is created when a propDocsWirelessMaclayer interface is detected in the head end unit. The entry is deleted after the associated propDocsWirelessMaclayer interface is removed. | |
| U32 p2mpHeAlcInterval | 1.3.6.1.4.1.9.9.170.1.3.1.1.2 | Unsigned32 | read-write | This object represents the scheduling interval. It is the regular interval at which the ALC grant in Map is transmitted to the SU's |
| U32 p2mpHeAlcNumMiniSlots | 1.3.6.1.4.1.9.9.170.1.3.1.1.3 | Unsigned32 | read-write | This indicates the number of minislots within each grant. |
| p2mpHeAlcTable | 1.3.6.1.4.1.9.9.170.1.3.1 | not-accessible | This table contains Automatic Line Control (ALC) configuration information. It is supported at the head end only. | |
| U32 p2mpHeIfInpFreq | 1.3.6.1.4.1.9.9.170.1.3.2.1.4 | Unsigned32 | read-only | This object represents the IF input frequency. |
| U32 p2mpHeIfOutFreq | 1.3.6.1.4.1.9.9.170.1.3.2.1.5 | Unsigned32 | read-only | This object represents the IF output frequency. |
| CWR p2mpHeIfRefOscState | 1.3.6.1.4.1.9.9.170.1.3.2.1.3 | CwrOscState | read-only | This object indicates the state of the IF reference oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly. |
| CWR p2mpHeIfRxOscState | 1.3.6.1.4.1.9.9.170.1.3.2.1.2 | CwrOscState | read-only | This object indicates the state of the IF receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly. |
| CWR p2mpHeIfTxOscState | 1.3.6.1.4.1.9.9.170.1.3.2.1.1 | CwrOscState | read-only | This object indicates the state of the IF transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly. |
| p2mpHeIntFreqEntry | 1.3.6.1.4.1.9.9.170.1.3.2.1 | not-accessible | The entry of this table is created when the managed system detects a propDocsWirelessMaclayer interface in the head end unit. The entry is deleted when the associated propDocsWirelessMaclayer interface is removed. | |
| p2mpHeIntFreqTable | 1.3.6.1.4.1.9.9.170.1.3.2 | not-accessible | This table contains information about the state of the intermediate frequency subsystem in the radio system. This table is supported at the head end only. | |
| T/F p2mpHeTrapEnable | 1.3.6.1.4.1.9.9.170.1.3.2.1.6 | TruthValue | read-write | When set to true(1), this enables the notifications that are specific to the head end. When set to false(2), these notifications are disabled. |
| STR p2mpLastPhyFailureReason | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.9 | DisplayString | read-only | This is a text string that describes the last physical link failure identified by p2mpLastPhyFailureType. |
| INT p2mpLastPhyFailureType | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.8 | INTEGER | read-only | This object indicates the last physical link failure that resulted in a p2mpRadioPhyFailNotification trap. none(1) - no failure p2mpHwConfigUnsupported(2) - The radio subsystem has detected that the configuration requested is not supported by the hardware. The p2mpLastPhyFailureReason variable will indicate which configuration parameter is not supported. p2mpHwConfigMismatch(3) - The radio subsystem has detected that the combination of the configuration parameters requested is inconsistent and cannot be supported. The p2mpLastPhyFailReason variable will indicate the configuration parameter that causes the mismatch. p2mpHwInitFailure(4) - The radio subsystem has failed to initialize the hardware. This implies that there is a critical error condition in the associated hardware. The p2mpLastPhyFailReason specifies the reason why the init failed. p2mpHostIfCommLinkError(5) - The host could not communicate with the IF module. p2mpAutoCableCompFailure(6) - Failed to achieve automatic cable compensation due to loss of Tx signal. |
| p2mpLedEntry | 1.3.6.1.4.1.9.9.170.1.1.4.1.1 | not-accessible | An entry in the table, containing the LED information. The entPhysicalIndex identifies the entity on which the LED's are present. | |
| p2mpLedGroup | 1.3.6.1.4.1.9.9.170.1.1.4 | |||
| I32 p2mpLedIndex | 1.3.6.1.4.1.9.9.170.1.1.4.1.1.1 | Integer32 | not-accessible | For a given entPhysicalIndex, this index value uniquely identifies an entry in the p2mpLedTable. |
| INT p2mpLedState | 1.3.6.1.4.1.9.9.170.1.1.4.1.1.3 | INTEGER | read-only | Indicates the state of the LED. |
| p2mpLedTable | 1.3.6.1.4.1.9.9.170.1.1.4.1 | not-accessible | Entity (Light emitting diode) LED information. For each LED on the entity, an entry will exist in this table, describing the location and current status of that LED. | |
| INT p2mpLedType | 1.3.6.1.4.1.9.9.170.1.1.4.1.1.2 | INTEGER | read-only | Indicates the type or label of the LED. |
| CWR p2mpLocalLoopbackAntenna | 1.3.6.1.4.1.9.9.170.1.1.3.1.1.2 | CwrRfType | read-write | This object identifies the RF resource used for loopback testing. This object is not applicable for loopback testing when p2mpLocalLoopbackMode has a value of 'noLoopback(1)'. |
| U32 p2mpLocalLoopbackChannel | 1.3.6.1.4.1.9.9.170.1.1.3.1.1.3 | Unsigned32 | read-write | This object identifies the channel being used to loopback the data. This object is not applicable for loopback testing when p2mpLocalLoopbackMode has a value of 'noLoopback(1)'. |
| INT p2mpLocalLoopbackMode | 1.3.6.1.4.1.9.9.170.1.1.3.1.1.1 | INTEGER | read-write | This object is used to configure the system in loopback mode prior to executing some system diagnostic tests. The user selects the point in the system where the data signal should be looped back. The diagnostic tests outlined in the user manual have to be manually executed to determine success or failure. Once all the tests are completed, normal operation is restored by setting this object to noLoopback(1). noLoopback(1) - no loopback fir(2) - loopback at the Finite Impulse Response (FIR) module. if(3) - loopback at the IF module. This exercises the FIR, and IF modules. rf(4) - loopback at the RF unit. This exercises the FIR, IF, and RF modules. This mode is supported only when p2mpRfLoopbackSupported is true(1). |
| p2mpLoopbackEntry | 1.3.6.1.4.1.9.9.170.1.1.3.1.1 | not-accessible | This represents one entry in the p2mpLoopbackTable. It is created when the managed system detects a propDocsWirelessMaclayer interface. The entry is removed when the associated propDocsWirelessMaclayer interface is deleted from the ifTable. | |
| p2mpLoopbackTable | 1.3.6.1.4.1.9.9.170.1.1.3.1 | not-accessible | This table provides facilities to establish loopback points to exercise various sections of the hardware. | |
| I32 p2mpMaxTxPower | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.9 | Integer32 | read-only | This object represents the maximum power that the RF subsystem can supply the antenna. |
| I32 p2mpMinTxPower | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.8 | Integer32 | read-only | This object represents the minimum power that the RF subsystem can supply the antenna. |
| p2mpPhyConfigGroup | 1.3.6.1.4.1.9.9.170.1.1.1 | |||
| p2mpPhyMIBNotification | 1.3.6.1.4.1.9.9.170.2.0 | |||
| p2mpPhyMIBNotificationPrefix | 1.3.6.1.4.1.9.9.170.2 | |||
| p2mpRadioAntennaGroup | 1.3.6.1.4.1.9.9.170.1.4.2.8 | Group of objects implemented in the point to multi point wireless system for managing the antennas available in the system. | ||
| p2mpRadioBaseObjects | 1.3.6.1.4.1.9.9.170.1.1 | |||
| p2mpRadioHeGroup | 1.3.6.1.4.1.9.9.170.1.4.2.6 | Group of objects implemented at the Head End. | ||
| p2mpRadioHeObjects | 1.3.6.1.4.1.9.9.170.1.3 | |||
| p2mpRadioObjects | 1.3.6.1.4.1.9.9.170.1 | |||
| p2mpRadioPhyCompliance | 1.3.6.1.4.1.9.9.170.1.4.1.1 | The compliance statement for devices that implement Point to Multipoint wireless interfaces compliant with the Cisco Systems Inc. specification. | ||
| p2mpRadioPhyCompliances | 1.3.6.1.4.1.9.9.170.1.4.1 | |||
| p2mpRadioPhyConformance | 1.3.6.1.4.1.9.9.170.1.4 | |||
| p2mpRadioPhyEntry | 1.3.6.1.4.1.9.9.170.1.1.1.1.1 | not-accessible | The entry of this table is created when the managed system detects a propDocsWirelessMaclayer interface. The entry is removed when the associated propDocsWirelessMaclayer interface is deleted from the ifTable. | |
| NTF p2mpRadioPhyFailNotification | 1.3.6.1.4.1.9.9.170.2.0.1 | A p2mpRadioPhyFailNotification is sent if the value of p2mpLastPhyFailureType changes due to the new failure being detected in the Radio interface. | ||
| p2mpRadioPhyGroups | 1.3.6.1.4.1.9.9.170.1.4.2 | |||
| p2mpRadioPhyTable | 1.3.6.1.4.1.9.9.170.1.1.1.1 | not-accessible | This table provides facilities to configure the physical layer characteristics of the radio link. The objects in this table are supported on the head end and at the subscriber unit. | |
| p2mpRadioSuGroup | 1.3.6.1.4.1.9.9.170.1.4.2.5 | Group of objects implemented at the Subscriber unit. | ||
| p2mpRadioSuObjects | 1.3.6.1.4.1.9.9.170.1.2 | |||
| p2mpRadioTestGroup | 1.3.6.1.4.1.9.9.170.1.1.3 | |||
| p2mpRfEntry | 1.3.6.1.4.1.9.9.170.1.1.2.1.1 | not-accessible | This represents one entry in the p2mpRfTable. An entry is created in this table when the managed system detects a RF resource. The entry is removed when the RF resource is removed from the wireless system. | |
| I32 p2mpRfIndex | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.1 | Integer32 | not-accessible | This object, along with the ifIndex of the MAC layer, represents the index of this entry in the p2mpRfTable. Each entry in the table provides details on the state of the RF resources available in the system. |
| T/F p2mpRfLoopbackSupported | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.15 | TruthValue | read-only | This object indicates if the RF unit supports loopback. When true(1), the user can configure loopback using the objects in p2mpLoopbackTable. When false(2), any attempt to configure RF loopback will fail. |
| INT p2mpRfOpMode | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.3 | INTEGER | read-only | This object specifies whether this RF resource can either transmit, receive, or do both. |
| CWR p2mpRfResource | 1.3.6.1.4.1.9.9.170.1.1.2.3.1.2 | CwrRfType | read-only | This object identifies if the antenna is connected to the main or the diversity RF resource. |
| CWR p2mpRfRxOscState | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.12 | CwrOscState | read-only | This object represents the state of the receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly. |
| INT p2mpRfStatus | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.14 | INTEGER | read-only | This object specifies whether the RF resource is functioning properly. If it is functioning properly then it will be online(1), else offline(2). At the Subscriber Unit, this object will reflect offline(2) if p2mpTxMuteEnable in the p2mpSuRadioPhyTable is true(1). |
| INT p2mpRfSupplyVoltageState | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.13 | INTEGER | read-only | This object specifies whether the voltage supply to the RF unit is within specifications or not. Voltage specifications are hardware dependent. |
| p2mpRfTable | 1.3.6.1.4.1.9.9.170.1.1.2.1 | not-accessible | This table contains information about the state of the radio frequency resources used by the radio system. Physically each RF resource may be realized by one antenna and its associated control hardware. A single antenna and its associated electronics may act as more than 1 RF resource. When an RF resource acts as both a transmit and receive resource, the transmit and receive frequency ranges may overlap. | |
| I32 p2mpRfTemperature | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.10 | Integer32 | read-only | This object represents the current temperature of the RF unit |
| CWR p2mpRfTxOscState | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.11 | CwrOscState | read-only | This object represents the state of the transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly. |
| CWR p2mpRfType | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.2 | CwrRfType | read-only | This object identifies the RF resource. |
| CWR p2mpRxFreqRangeMax | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.7 | CwrRfFreqRange | read-only | This object represents the highest transmission frequency that this RF resource can receive. |
| CWR p2mpRxFreqRangeMin | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.6 | CwrRfFreqRange | read-only | This object represents the lowest transmission frequency this RF resource can receive. |
| T/F p2mpSelfTest | 1.3.6.1.4.1.9.9.170.1.1.1.1.1.1 | TruthValue | read-write | This object is used to enable/disable self test. When set to true(1), the software tests the memory and hardware integrity shortly after the router powers up. |
| CWR p2mpSuCenterFrequency | 1.3.6.1.4.1.9.9.170.1.2.2.1.2 | CwrRfFreqRange | read-only | This object indicates the frequency at which the receive power at the subscriber unit was measured. |
| I32 p2mpSuMeasuredPower | 1.3.6.1.4.1.9.9.170.1.2.2.1.3 | Integer32 | read-only | This object represents the power measured at the frequency indicated by p2mpSuCenterFrequency. |
| p2mpSuPowerScanEntry | 1.3.6.1.4.1.9.9.170.1.2.2.1 | not-accessible | An entry containing the power related status information of the propDocsWirelessMaclayer interface in the subscriber unit. The entry is created when a propDocsWirelessMaclayer interface is detected in the subscriber unit. The entry is deleted after the associated propDocsWirelessMaylayer interface is removed. | |
| I32 p2mpSuPowerScanIndex | 1.3.6.1.4.1.9.9.170.1.2.2.1.1 | Integer32 | not-accessible | For a given ifIndex, this index value uniquely identifies an entry in the p2mpSuPowerScanTable. |
| p2mpSuPowerScanTable | 1.3.6.1.4.1.9.9.170.1.2.2 | not-accessible | This table contains information about the receive power measured at the different possible center frequencies. | |
| p2mpSuRadioPhyEntry | 1.3.6.1.4.1.9.9.170.1.2.1.1 | not-accessible | An entry containing the radio configuration information of the propDocsWirelessMaclayer interface in the subscriber unit. The entry is created when a propDocsWirelessMaclayer interface is detected in the subscriber unit. The entry is deleted when the associated propDocsWirelessMaclayer interface is removed. | |
| p2mpSuRadioPhyTable | 1.3.6.1.4.1.9.9.170.1.2.1 | not-accessible | This table contains information about the currently configured physical layer interfaces in the subscriber unit. | |
| U32 p2mpSuTxMuteDuration | 1.3.6.1.4.1.9.9.170.1.2.1.1.2 | Unsigned32 | read-write | This object indicates the duration of time (in minutes) for which the subscriber transmission will be turned off. |
| T/F p2mpSuTxMuteEnable | 1.3.6.1.4.1.9.9.170.1.2.1.1.1 | TruthValue | read-only | When true(1), this object indicates the subscriber unit transmission has been turned off for a duration indicated by p2mpSuTxMuteDuration. When false(2), this object indicates that the subscriber unit is transmitting. |
| NTF p2mpTrapHeIfExtRefOsc | 1.3.6.1.4.1.9.9.170.2.0.11 | The IF Reference Frequency oscillator has changed state. | ||
| NTF p2mpTrapHeIfRxOsc | 1.3.6.1.4.1.9.9.170.2.0.9 | The IF receive frequency oscillator has changed state. | ||
| NTF p2mpTrapHeIfTxOsc | 1.3.6.1.4.1.9.9.170.2.0.10 | The IF transmit frequency oscillator has changed state. | ||
| NTF p2mpTrapRfCommLinkError | 1.3.6.1.4.1.9.9.170.2.0.6 | This trap indicates that the host and the IF module cannot communicate with the RF resource identified by p2mpRfType. | ||
| NTF p2mpTrapRfRxOsc | 1.3.6.1.4.1.9.9.170.2.0.3 | The RF receive frequency oscillator has changed state. The p2mpRfRxOscState specifies the current state of the oscillator. | ||
| NTF p2mpTrapRfStatusChange | 1.3.6.1.4.1.9.9.170.2.0.8 | This trap indicates that the RF resource either came online(1) or went offline(2). | ||
| NTF p2mpTrapRfSupplyVoltage | 1.3.6.1.4.1.9.9.170.2.0.2 | The supply voltage to the RF resource has changed. The p2mpRfSupplyVoltageState specifies whether the supply voltage is in spec or not. | ||
| NTF p2mpTrapRfTemp | 1.3.6.1.4.1.9.9.170.2.0.5 | The temperature of the RF module identified by p2mpRfIndex has exceeded a defined reference. | ||
| NTF p2mpTrapRfTxOsc | 1.3.6.1.4.1.9.9.170.2.0.4 | The RF transmit frequency oscillator has changed state. The p2mpRfRxOscState specifies the state of the oscillator. | ||
| NTF p2mpTrapTxPower | 1.3.6.1.4.1.9.9.170.2.0.7 | This trap indicates that the transmit power for the RF resource identified by p2mpRfType exceeded a predefined threshold. | ||
| CWR p2mpTxFreqRangeMax | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.5 | CwrRfFreqRange | read-only | This object represents the maximum frequency at which this RF resource can transmit. |
| CWR p2mpTxFreqRangeMin | 1.3.6.1.4.1.9.9.170.1.1.2.1.1.4 | CwrRfFreqRange | read-only | This object represents the minimum frequency at which this RF resource can transmit. |
RFC description
Wireless point-to-multipoint radio physical layer configuration and monitoring for Cisco systems.
Start monitoring Cisco wireless P2MP radio (head-end and subscriber-unit, legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.