All MIBs › CISCO-WIRELESS-P2MP-PHY-MIB › p2mpLocalLoopbackMode
p2mpLocalLoopbackMode
Module: CISCO-WIRELESS-P2MP-PHY-MIB
OID (symbolic): CISCO-WIRELESS-P2MP-PHY-MIB::p2mpLocalLoopbackMode
OID (numeric): 1.3.6.1.4.1.9.9.170.1.1.3.1.1.1
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This object is used to configure the system in loopback mode prior to executing some system diagnostic tests. The user selects the point in the system where the data signal should be looped back. The diagnostic tests outlined in the user manual have to be manually executed to determine success or failure. Once all the tests are completed, normal operation is restored by setting this object to noLoopback(1).
noLoopback(1) - no loopback fir(2) - loopback at the Finite Impulse Response (FIR) module. if(3) - loopback at the IF module. This exercises the FIR, and IF modules. rf(4) - loopback at the RF unit. This exercises the FIR, IF, and RF modules. This mode is supported only when p2mpRfLoopbackSupported is true(1).
What is p2mpLocalLoopbackMode?
This read-write object selects where in the signal chain, FIR, IF, or RF stage, the system should loop the data signal back to itself for diagnostic testing, or noLoopback(1) for normal operation. Per the desc, the admin must manually run the diagnostic tests described in the user manual after setting this and must set it back to noLoopback(1) to restore normal service. For example, a technician suspecting an IF-stage fault would set p2mpLocalLoopbackMode to if(3), run the prescribed test, and then return the object to noLoopback(1) once finished.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.9.170.1.1.3.1.1.1 snmpwalk -v2c -c public <target> CISCO-WIRELESS-P2MP-PHY-MIB::p2mpLocalLoopbackMode
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.9.170.1.1.3.1.1.1.1 snmpget -v2c -c public <target> CISCO-WIRELESS-P2MP-PHY-MIB::p2mpLocalLoopbackMode.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.9.170.1.1.3.1.1.1.1 i <value>
Start monitoring Cisco wireless P2MP radio (head-end and subscriber-unit, legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-WIRELESS-P2MP-PHY-MIB::p2mpLocalLoopbackMode OID value, configure state conditions and alerts, and monitor any Cisco wireless P2MP radio (head-end and subscriber-unit, legacy) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.9 | ciscoMgmt | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.9.170 | ciscoWirelessPhyMIB | CISCO-WIRELESS-P2MP-PHY-MIB |
| 1.3.6.1.4.1.9.9.170.1 | p2mpRadioObjects | CISCO-WIRELESS-P2MP-PHY-MIB |
| 1.3.6.1.4.1.9.9.170.1.1 | p2mpRadioBaseObjects | CISCO-WIRELESS-P2MP-PHY-MIB |
| 1.3.6.1.4.1.9.9.170.1.1.3 | p2mpRadioTestGroup | CISCO-WIRELESS-P2MP-PHY-MIB |
| 1.3.6.1.4.1.9.9.170.1.1.3.1 | p2mpLoopbackTable | CISCO-WIRELESS-P2MP-PHY-MIB |
| 1.3.6.1.4.1.9.9.170.1.1.3.1.1 | p2mpLoopbackEntry | CISCO-WIRELESS-P2MP-PHY-MIB |
| 1.3.6.1.4.1.9.9.170.1.1.3.1.1.1 | p2mpLocalLoopbackMode | CISCO-WIRELESS-P2MP-PHY-MIB |