All MIBs › TIMETRA-SAP-MIB
Organization: Alcatel
Last Updated: 2007-10-01
Description: TIMETRA-SAP-MIB module
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TIMETRA-SAP-MIB?
TIMETRA-SAP-MIB is an Alcatel-Lucent (Nokia) proprietary MIB for the 7x50 Service Router (SR) family, managing Service Access Points (SAPs) — the customer-facing service instances bound to ports and encapsulation values on the router. It exposes configuration and status data for each SAP, including the port it is bound to, encapsulation value, SAP type and description, and ingress QoS/MAC-filter policy assignments. It directly supports monitoring device operational status through sapAdminStatus and sapOperStatus per SAP, letting an operator detect a service that is administratively enabled but operationally down, and it defines a trap prefix for SAP-related fault notifications. TIMETRA-SAP-MIB SNMP monitoring is commonly used by service providers to verify that customer-facing SAPs remain operationally up after provisioning changes. It is a Nokia/Alcatel-Lucent proprietary MIB with no stated dependency on external IETF standards, built specifically for the TiMOS-based 7x50 SR service model, and it is deployed on Alcatel-Lucent/Nokia 7x50 Service Router platforms delivering Carrier Ethernet, VPLS, or VPRN services to end customers.
IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-SAP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia/Alcatel-Lucent 7x50 Service Router family, entire product line (Service Access Point admin/oper status)
Monitoring Examples
An operator walks sapBaseInfoTable/sapBaseInfoEntry, keyed by sapPortId and sapEncapValue, to compare sapAdminStatus against sapOperStatus for each SAP; a SAP administratively up but operationally down points to a physical port or encapsulation mismatch. sapNumEntries gives a quick count of provisioned SAPs to detect unexpected additions or deletions. sapIngressQosPolicyId and sapIngressMacFilterId are checked to confirm the correct QoS and filtering policy is applied to a customer's service instance, and sapRowStatus reveals SAPs left in a non-active provisioning state.
What Can Be Monitored
- SAP admin status
- SAP operational status
- SAP count
- ingress QoS policy assignment
- ingress MAC filter assignment
- SAP encapsulation configuration
This MIB depends on
Related MIBs
Imported Objects
From ATM-TC-MIB
| AtmTrafficDescrParamIndex |
From IF-MIB
| InterfaceIndexOrZero |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TimeStamp | |
| TruthValue |
From TIMETRA-FILTER-MIB
| TFilterID |
From TIMETRA-GLOBAL-MIB
| timetraSRMIBModules | OBJECT-IDENTITY |
From TIMETRA-QOS-MIB
| tSchedulerPolicyName | OBJECT-TYPE |
| tVirtualSchedulerName | OBJECT-TYPE |
From TIMETRA-SERV-MIB
| BridgeId | |
| CemSapEcid | |
| CemSapReportAlarm | |
| ConfigStatus | |
| L2ptProtocols | |
| MstiInstanceIdOrZero | |
| MvplsPruneState | |
| ServObjDesc | |
| ServObjName | |
| ServType | |
| StpExceptionCondition | |
| StpPortRole | |
| StpProtocol | |
| TQosQueueAttribute | |
| TSapEgrQueueId | |
| TSapIngQueueId | |
| TStpPortState | |
| TVirtSchedAttribute | |
| TdmOptionsCasTrunkFraming | |
| TlsLimitMacMove | |
| TlsLimitMacMoveLevel | |
| VpnId | |
| custId | OBJECT-TYPE |
| hostConnectivityChAddr | OBJECT-TYPE |
| hostConnectivityCiAddr | OBJECT-TYPE |
| hostConnectivityCiAddrType | OBJECT-TYPE |
| protectedMacForNotify | OBJECT-TYPE |
| staticHostDynamicMacConflict | OBJECT-TYPE |
| staticHostDynamicMacIpAddress | OBJECT-TYPE |
| svcDhcpClientLease | OBJECT-TYPE |
| svcDhcpCoAError | OBJECT-TYPE |
| svcDhcpLseStateNewChAddr | OBJECT-TYPE |
| svcDhcpLseStateNewCiAddr | OBJECT-TYPE |
| svcDhcpLseStateOldChAddr | OBJECT-TYPE |
| svcDhcpLseStateOldCiAddr | OBJECT-TYPE |
| svcDhcpLseStatePopulateError | OBJECT-TYPE |
| svcDhcpPacketProblem | OBJECT-TYPE |
| svcDhcpProxyError | OBJECT-TYPE |
| svcDhcpSubAuthError | OBJECT-TYPE |
| svcId | OBJECT-TYPE |
| svcTlsMacMoveMaxRate | OBJECT-TYPE |
| svcVpnId | OBJECT-TYPE |
| tlsDHCPClientLease | OBJECT-TYPE |
| tlsDhcpLseStateNewChAddr | OBJECT-TYPE |
| tlsDhcpLseStateNewCiAddr | OBJECT-TYPE |
| tlsDhcpLseStateOldChAddr | OBJECT-TYPE |
| tlsDhcpLseStateOldCiAddr | OBJECT-TYPE |
| tlsDhcpPacketProblem | OBJECT-TYPE |
| tlsMstiInstanceId | OBJECT-TYPE |
| tmnxCustomerBridgeId | OBJECT-TYPE |
| tmnxCustomerRootBridgeId | OBJECT-TYPE |
| tmnxOtherBridgeId | OBJECT-TYPE |
| tmnxServConformance | OBJECT-IDENTITY |
| tmnxServNotifications | OBJECT-IDENTITY |
| tmnxServObjs | OBJECT-IDENTITY |
| tstpTraps | OBJECT-IDENTITY |
From TIMETRA-TC-MIB
| ServiceAdminStatus | |
| TAdaptationRule | |
| TBurstPercentOrDefault | |
| TBurstSize | |
| TCIRRate | |
| TCpmProtPolicyID | |
| TEgressQueueId | |
| TIngressQueueId | |
| TItemDescription | |
| TNamedItem | |
| TNamedItemOrEmpty | |
| TPIRRate | |
| TPolicyStatementNameOrEmpty | |
| TPortSchedulerPIR | |
| TSapEgressPolicyID | |
| TSapIngressPolicyID | |
| TmnxActionType | |
| TmnxCustId | |
| TmnxEnabledDisabled | |
| TmnxEncapVal | |
| TmnxIgmpVersion | |
| TmnxOperState | |
| TmnxPortID | |
| TmnxServId |
How to Use in IPNetwork Monitor
Example using sapNumEntries OID:
Select a Nokia 7750 SR-s (current) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type sapNumEntries into the Find box to locate it in the OID tree, then select it and click OK. It reports the current number of Service Access Points (SAPs) configured on this router. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the SAP count changes unexpectedly, which would indicate an unplanned service-provisioning change. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF bridgedTLS | 1.3.6.1.4.1.6527.3.1.3.4.5.0.10 | The bridgedTLS notification is generated when a configuration BPDU has been received that identifies that another TLS with a different VPNID is attempting to bridge with this TLS. At least one ESR participating within one of the TLS that is locally connected must have an active VCP for this to be seen. The SAP that the configuration BPDU is received on will be blocked to prevent the TLS to TLS bridging. Reconfigure the bridged TLS into a single TLS or remove the connectivity. | ||
| NTF higherPriorityBridge | 1.3.6.1.4.1.6527.3.1.3.4.5.0.9 | The higherPriorityBridge notification is generated when a customer's device has been configured with a bridge priority equal to zero. The SAP that the customer's device is connected through will be blocked. Remove the customer's device or reconfigure the customer's bridge priority with a value greater than zero. | ||
| NTF hostConnectivityLost | 1.3.6.1.4.1.6527.3.1.3.4.3.0.13 | The hostConnectivityLost notification indicates that the system lost the connectivity with the indicated host. | ||
| NTF hostConnectivityRestored | 1.3.6.1.4.1.6527.3.1.3.4.3.0.14 | The hostConnectivityRestored notification indicates that the system has restored the connectivity with the indicated host. | ||
| msapCaptureSapStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.49.1 | not-accessible | Statistics for a specific 'capture' SAP. | |
| C32 msapCaptureSapStatsPktsDropped | 1.3.6.1.4.1.6527.3.1.2.4.3.49.1.4 | Counter32 | read-only | The value of msapCaptureSapStatsPktsDropped indicates the number of packets dropped on this 'capture' SAP. |
| C32 msapCaptureSapStatsPktsRecvd | 1.3.6.1.4.1.6527.3.1.2.4.3.49.1.2 | Counter32 | read-only | The value of msapCaptureSapStatsPktsRecvd indicates the number of packets received on this 'capture' SAP. |
| C32 msapCaptureSapStatsPktsRedirect | 1.3.6.1.4.1.6527.3.1.2.4.3.49.1.3 | Counter32 | read-only | The value of msapCaptureSapStatsPktsRedirect indicates the number of packets redirected on this 'capture' SAP. |
| msapCaptureSapStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.49 | not-accessible | A table that contains statistics for SAPs with a sapSubType value of 'capture'. | |
| INT msapCaptureSapStatsTriggerType | 1.3.6.1.4.1.6527.3.1.2.4.3.49.1.1 | INTEGER | not-accessible | The value of msapCaptureSapStatsTriggerType indicates the type of trigger packets this entry is for. |
| NTF msapCreationFailure | 1.3.6.1.4.1.6527.3.1.3.4.3.0.26 | The trap msapCreationFailure is sent whenever the system fails to create a managed SAP. The svcId, svcVpnId, sapPortId and sapEncapValue are those of the capturing SAP. | ||
| msapIgmpSnpgMcacLagEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.47.1 | not-accessible | Each row entry represents a particular multicast CAC lag port constraints for a Managed SAP policy.. Entries are created and deleted by the user. | |
| TIM msapIgmpSnpgMcacLagLastChanged | 1.3.6.1.4.1.6527.3.1.2.4.3.47.1.3 | TimeStamp | read-only | The value of msapIgmpSnpgMcacLagLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| U32 msapIgmpSnpgMcacLagLevel | 1.3.6.1.4.1.6527.3.1.2.4.3.47.1.4 | Unsigned32 | read-create | The value of msapIgmpSnpgMcacLagLevel specifies the level id to use when the value of msapIgmpSnpgMcacLagPortsDown matches the actual number of ports down in a lag. Using the value of msapIgmpSnpgMcacLagLevel as an index, the operational MSAP unconstrained bandwidth will be set to msapIgmpSnpgMcacLevelBW. By default, for all lag constraints the link level will be set to 1 at row creation. |
| U32 msapIgmpSnpgMcacLagPortsDown | 1.3.6.1.4.1.6527.3.1.2.4.3.47.1.1 | Unsigned32 | not-accessible | The value of msapIgmpSnpgMcacLagPortsDown indicates the configured number of ports in a lag group that are down. If the number of ports available in the lag is reduced by the number of ports configured for msapIgmpSnpgMcacLagPortsDown object then bandwidth allowed for bundle will be updated to the value of msapIgmpSnpgMcacLevelBW indexed by msapIgmpSnpgMcacLagLevel value. |
| ROW msapIgmpSnpgMcacLagRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.47.1.2 | RowStatus | read-create | The value of msapIgmpSnpgMcacLagRowStatus is used for creation and deletion of lag constraint in a CAC policy. |
| msapIgmpSnpgMcacLagTable | 1.3.6.1.4.1.6527.3.1.2.4.3.47 | not-accessible | The msapIgmpSnpgMcacLagTable has an entry for each lag port configured for a multicast CAC policy bundle configured for a Managed SAP policy. | |
| TIM msapIgmpSnpgMcacLagTblLastChgd | 1.3.6.1.4.1.6527.3.1.2.4.3.62 | TimeStamp | read-only | The value of msapIgmpSnpgMcacLagTblLastChgd indicates the sysUpTime at the time of the last modification of msapIgmpSnpgMcacLagTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| U32 msapIgmpSnpgMcacLevelBW | 1.3.6.1.4.1.6527.3.1.2.4.3.46.1.4 | Unsigned32 | read-create | The value of msapIgmpSnpgMcacLevelBW specifies the bandwidth in kilo-bits per second (kbps) for the level. |
| msapIgmpSnpgMcacLevelEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.46.1 | not-accessible | Each row entry represents a multicast CAC policy bundle level constraints for a particular Managed SAP policy. Entries are created and deleted by the user. | |
| U32 msapIgmpSnpgMcacLevelId | 1.3.6.1.4.1.6527.3.1.2.4.3.46.1.1 | Unsigned32 | not-accessible | The value of msapIgmpSnpgMcacLevelId indicates the level id of the multicast CAC policy bundle constraint. The value of level 1 has the highest priority and level 8 the lowest. |
| TIM msapIgmpSnpgMcacLevelLastChanged | 1.3.6.1.4.1.6527.3.1.2.4.3.46.1.3 | TimeStamp | read-only | The value of msapIgmpSnpgMcacLevelLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| ROW msapIgmpSnpgMcacLevelRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.46.1.2 | RowStatus | read-create | The value of msapIgmpSnpgMcacLevelRowStatus is used for creation and deletion of level constraint in a CAC for a Managed SAP policy. |
| msapIgmpSnpgMcacLevelTable | 1.3.6.1.4.1.6527.3.1.2.4.3.46 | not-accessible | The msapIgmpSnpgMcacLevelTable has an entry for each multicast CAC policy constraint level configured for a Managed SAP policy. | |
| TIM msapIgmpSnpgMcacLvlTblLastChgd | 1.3.6.1.4.1.6527.3.1.2.4.3.61 | TimeStamp | read-only | The value of msapIgmpSnpgMcacLvlTblLastChgd indicates the sysUpTime at the time of the last modification of msapIgmpSnpgMcacLevelTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| TNA msapInfoCreationPlcyName | 1.3.6.1.4.1.6527.3.1.2.4.3.48.1.2 | TNamedItem | read-only | The value of msapInfoCreationPlcyName indicates the value of the msapPlcyName object for MSAP policy used to create this MSAP. |
| TMN msapInfoCreationSapPortEncapVal | 1.3.6.1.4.1.6527.3.1.2.4.3.48.1.1 | TmnxEncapVal | read-only | The value of msapInfoCreationSapPortEncapVal indicates the port encapsulation value of the SAP with a sapSubType value of 'capture' that created this MSAP. |
| msapInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.48.1 | not-accessible | Information about a specific Managed SAP. | |
| TIM msapInfoLastChanged | 1.3.6.1.4.1.6527.3.1.2.4.3.48.1.4 | TimeStamp | read-only | The value of msapInfoLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| TMN msapInfoReEvalPolicy | 1.3.6.1.4.1.6527.3.1.2.4.3.48.1.3 | TmnxActionType | read-write | The value of msapInfoReEvalPolicy specifies whether to re-apply the Managed SAP policy associated with this MSAP. When a SET of this object is done with a value of 'doAction', the system will attempt to re-apply the MSAP policy indicated by msapInfoCreationPlcyName. If this action is successful, 'noError' will be returned. If this action is unsuccessful, an 'inconsistentValue' error will be returned. Attempting to SET this object with a value of 'notApplicable' will have no effect and will return 'noError'. SNMP GET and GETNEXT requests on this object will return 'notApplicable'. |
| msapInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.48 | not-accessible | A table that contains Managed SAP information. | |
| TIM msapInfoTblLastChgd | 1.3.6.1.4.1.6527.3.1.2.4.3.63 | TimeStamp | read-only | The value of msapInfoTblLastChgd indicates the sysUpTime at the time of the last modification of msapInfoTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| C32 msapPlcyAssociatedMsaps | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.19 | Counter32 | read-only | The value of msapPlcyAssociatedMsaps indicates the number of MSAPs associated with this MSAP policy. |
| T/F msapPlcyCpmProtMonitorMac | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.6 | TruthValue | read-create | The value of msapPlcyCpmProtMonitorMac specifies whether the tmnxCpmProtPolPerSrcRateLimit of the CPM Protection policy, as specified by msapPlcyCpmProtPolicyId, must be applied. If the value of msapPlcyCpmProtMonitorMac is 'true', the per-source rate limit must be applied. If the value of msapPlcyCpmProtPolicyId is equal to zero, the value of msapPlcyCpmProtMonitorMac is irrelevant and will be ignored. This object is not supported on SR-1 and ESS-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '5', and 7710, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '7' or '9'. An attempt to set msapPlcyCpmProtMonitorMac to 'true' on one of these unsupported chassis types will return an 'inconsistentValue' error. |
| TCP msapPlcyCpmProtPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.5 | TCpmProtPolicyID | read-create | The value of msapPlcyCpmProtPolicyId specifies a CPM Protection policy for the MSAP policy. If a corresponding policy is not defined in TIMETRA-SECURITY-MIB::tmnxCpmProtPolTable, an 'inconsistentValue' error will be returned. A value of one specifies that the default CPM Protection policy is associated with the Managed SAP. This object is not supported on SR-1 and ESS-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '5', and 7710, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '7' or '9'. An attempt to set msapPlcyCpmProtPolicyId to a non-zero value on one of these unsupported chassis types will return an 'inconsistentValue' error. |
| TIT msapPlcyDescription | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.4 | TItemDescription | read-create | The value of msapPlcyDescription specifies the description of the MSAP policy. |
| msapPlcyEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1 | not-accessible | Each entry represents the configuration for a managed SAP(MSAP) policy. The values for each entry will be used to populate the following tables when the MSAP policy is applied to a MSAP: TIMETRA-SAP-MIB::sapBaseInfoTable TIMETRA-SAP-MIB::sapSubMgmtInfoTable | |
| TIM msapPlcyLastChanged | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.3 | TimeStamp | read-only | The value of msapPlcyLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| TNA msapPlcyName | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.1 | TNamedItem | not-accessible | The value of msapPlcyName specifies the name of the MSAP policy. |
| ROW msapPlcyRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.2 | RowStatus | read-create | The value of msapPlcyRowStatus is used for the creation and deletion of MSAP policies. |
| TNA msapPlcySubMgmtDefAppProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.11 | TNamedItemOrEmpty | read-create | The value of msapPlcySubMgmtDefAppProfile specifies the default application profile applicable on the MSAP. If a corresponding profile is not defined in TIMETRA-BSX-MIB::tmnxBsxAppProfTable, an 'inconsistentValue' error will be returned. |
| TNA msapPlcySubMgmtDefSlaProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.10 | TNamedItemOrEmpty | read-create | The value of msapPlcySubMgmtDefSlaProfile specifies the default SLA profile applicable on the MSAP. If a corresponding profile is not defined in tmnxSLAProfileTable, an 'inconsistentValue' error will be returned. |
| INT msapPlcySubMgmtDefSubId | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.7 | INTEGER | read-create | The value of msapPlcySubMgmtDefSubId specifies what will be used as the default subscriber identification applicable on the MSAP. This value is used in case no other source (like Radius) provides a subscriber identification string. If the value of this object is set to 'useSapId', the SAP-id will be used as the default subscriber identification string. In this case, msapPlcySubMgmtDefSubIdStr must contain the empty string, so any non-empty string in msapPlcySubMgmtDefSubIdStr will be set to an empty string. If the value of this object is set to 'useString', the value of msapPlcySubMgmtDefSubIdStr will be used as the default subscriber identification string. In this case, an empty msapPlcySubMgmtDefSubIdStr means that there is no default subscriber identification configured. |
| TNA msapPlcySubMgmtDefSubIdStr | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.8 | TNamedItemOrEmpty | read-create | The value of msapPlcySubMgmtDefSubIdStr specifies the default subscriber identification string applicable on this MSAP. |
| TNA msapPlcySubMgmtDefSubProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.9 | TNamedItemOrEmpty | read-create | The value of msapPlcySubMgmtDefSubProfile specifies the default subscriber profile applicable on the MSAP. If a corresponding profile is not defined in tmnxSubProfileTable, an 'inconsistentValue' error will be returned. A value of 'default' is not allowed for this object. |
| TNA msapPlcySubMgmtNonSubTrafAppProf | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.18 | TNamedItemOrEmpty | read-create | The value of msapPlcySubMgmtNonSubTrafAppProf specifies the Application profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1. |
| TNA msapPlcySubMgmtNonSubTrafSlaProf | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.17 | TNamedItemOrEmpty | read-create | The value of msapPlcySubMgmtNonSubTrafSlaProf specifies the SLA profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1. |
| TNA msapPlcySubMgmtNonSubTrafSubId | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.15 | TNamedItemOrEmpty | read-create | The value of msapPlcySubMgmtNonSubTrafSubId specifies the subscriber identification applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1. |
| TNA msapPlcySubMgmtNonSubTrafSubProf | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.16 | TNamedItemOrEmpty | read-create | The value of msapPlcySubMgmtNonSubTrafSubProf specifies the subscriber profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1. |
| T/F msapPlcySubMgmtProfiledTrafOnly | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.14 | TruthValue | read-create | The value of msapPlcySubMgmtProfiledTrafOnly specifies whether only profiled traffic is applicable for the MSAP. If set to 'true', the MSAP queues will be deleted. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1. |
| TPO msapPlcySubMgmtSubIdPlcy | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.12 | TPolicyStatementNameOrEmpty | read-create | The value of msapPlcySubMgmtSubIdPlcy specifies the subscriber identification policy applicable on the MSAP. If a corresponding profile is not defined in tmnxSubIdentPolicyTable, an 'inconsistentValue' error will be returned. |
| U32 msapPlcySubMgmtSubscriberLimit | 1.3.6.1.4.1.6527.3.1.2.4.3.44.1.13 | Unsigned32 | read-create | The value of msapPlcySubMgmtSubscriberLimit specifies the maximum number of subscribers allowed for the MSAP. A value is 0 means there is no limit. The values for the objects msapPlcySubMgmtProfiledTrafOnly, msapPlcySubMgmtNonSubTrafSubProf, and msapPlcySubMgmtNonSubTrafSlaProf are only meaningful when the value of msapPlcySubMgmtSubscriberLimit is 1 and will not be used when the value of msapPlcySubMgmtSubscriberLimit is not 1. |
| msapPlcyTable | 1.3.6.1.4.1.6527.3.1.2.4.3.44 | not-accessible | The msapPlcyTable has an entry for each managed SAP(MSAP) policy configured in the system. | |
| TIM msapPlcyTblLastChgd | 1.3.6.1.4.1.6527.3.1.2.4.3.59 | TimeStamp | read-only | The value of msapPlcyTblLastChgd indicates the sysUpTime at the time of the last modification of msapPlcyTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| NTF msapStateChanged | 1.3.6.1.4.1.6527.3.1.3.4.3.0.25 | The msapStateChanged notification is generated when a Managed SAP is 'created', 'modified', or 'deleted', with the value of msapStatus indicated which state it has entered. | ||
| CON msapStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.100.2 | ConfigStatus | accessible-for-notify | The status of the Managed SAP which is used by the msapStateChanged notification to indicate what state the Managed SAP has entered: 'created', 'modified', or 'deleted'. |
| INT msapTlsPlcyArpReplyAgent | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.3 | INTEGER | read-create | The value of msapTlsPlcyArpReplyAgent specifies the status of the special ARP response mechanism in the system for ARP requests destined to static or dynamic hosts associated with the MSAP. 'disabled' - the ARP reply function is not operational 'enabled' - the ARP reply function is enabled without subscriber identification. 'enabledWithSubscrIdent' - the ARP reply function is enabled with subscriber identification. |
| INT msapTlsPlcyDhcpCircuitId | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.12 | INTEGER | read-create | The value of msapTlsPlcyDhcpCircuitId specifies whether or not the circuit-id suboption is present, and if it is present what information goes in it: none - the circuit-id suboption will not be part of the information option (Option 82). asciiTuple - the ASCII-encoded concatenated tuple consisting of the - access-node-identifier - service-id - interface-name is used. vlanAsciiTuple - the format will include VLAN-id and dot1p bits in addition to what is included in ascii-tuple already. The format is supported on dot1q and qinq encapsulated ports only. Thus, when the option 82 bits are stripped, dot1p bits will be copied to the Ethernet header of an outgoing packet. |
| INT msapTlsPlcyDhcpInfoAction | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.11 | INTEGER | read-create | The value of msapTlsPlcyDhcpInfoAction specifies the DHCP option reforwarding policy: 'replace' - replace existing information with configured information 'drop' - discard messages with existing relay information if the option-82 information is also present 'keep' - retain the existing relay information |
| U32 msapTlsPlcyDhcpLeasePopulate | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.5 | Unsigned32 | read-create | The value of msapTlsPlcyDhcpLeasePopulate specifies the maximum number of DHCP lease states allowed on the MSAP. |
| TMN msapTlsPlcyDhcpPrxyAdminState | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.6 | TmnxEnabledDisabled | read-create | The value of msapTlsPlcyDhcpPrxyAdminState specifies the desired administrative state of the proxy server on the interface. |
| U32 msapTlsPlcyDhcpPrxyLeaseTime | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.9 | Unsigned32 | read-create | The value of msapTlsPlcyDhcpPrxyLeaseTime specifies, in seconds, how long a DHCP client is allowed to use the offered IP address. A value of 0 means the lease time provided by a RADIUS or an upstream DHCP server will not be overridden. A value of 7 days (315446399 seconds) is used when RADIUS does not provide a lease time. |
| T/F msapTlsPlcyDhcpPrxyLTRadOverride | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.10 | TruthValue | read-create | The value of msapTlsPlcyDhcpPrxyLTRadOverride specifies whether or not the lease time provided by the RADIUS server is presented to the DHCP client. By default the proxy-server will always make use of msapTlsPlcyDhcpPrxyLeaseTime, regardless of what lease time information is provided from the RADIUS server. When msapTlsPlcyDhcpPrxyLTRadOverride is set to 'true', the proxy-server will use the lease time information provided by the RADIUS server, regardless of the configured lease time. |
| IP msapTlsPlcyDhcpPrxyServAddr | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.8 | InetAddress | read-create | The value of msapTlsPlcyDhcpPrxyServAddr specifies the IP address of the which will be used as the source address of the emulated DHCP server in the context of the VPLS MSAP. This address is mandatory for the proxy server capability and it should be in the context of the subnet represented by the VPLS. |
| IPt msapTlsPlcyDhcpPrxyServAddrType | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.7 | InetAddressType | read-create | The value of msapTlsPlcyDhcpPrxyServAddrType specifies the address type of msapTlsPlcyDhcpPrxyServAddr. |
| INT msapTlsPlcyDhcpRemoteId | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.13 | INTEGER | read-create | The value of msapTlsPlcyDhcpRemoteId specifies what information goes into the remote-id suboption in the DHCP Relay packet. If the value of this object is set to 'none', the remote-id suboption will not be part of the information option (Option 82). If the value of this object is set to 'mac', the MAC address of the remote end is encoded in the suboption. If the value of this object is set to 'remote-id', msapTlsPlcyDhcpRemoteIdString will represent the remote-id. By default, the remote-id value is none. |
| TNA msapTlsPlcyDhcpRemoteIdString | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.14 | TNamedItemOrEmpty | read-create | The value of msapTlsPlcyDhcpRemoteIdString specifies the remote-id. The value of this object is ignored if msapTlsPlcyDhcpRemoteId does not have the value of 'remote-id'. |
| BIT msapTlsPlcyDhcpVendorInclOpts | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.15 | Bits | read-create | The value of msapTlsPlcyDhcpVendorInclOpts specifies what is encoded in the Alcatel-Lucent vendor specific sub-option of option 82. The value of this object is only used when msapTlsPlcyDhcpInfoAction is 'replace'. |
| TNA msapTlsPlcyDhcpVendorOptStr | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.16 | TNamedItemOrEmpty | read-create | The value of msapTlsPlcyDhcpVendorOptStr specifies the string that goes into the Alcatel-Lucent vendor specific sub-option of option 82. This string is only used when msapTlsPlcyDhcpInfoAction is set to 'replace'. |
| TNA msapTlsPlcyEgressMcastGroup | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.17 | TNamedItemOrEmpty | read-create | The value of msapTlsPlcyEgressMcastGroup specifies the Egress Multicast Group for the MSAP. |
| msapTlsPlcyEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1 | not-accessible | Each entry represents the VPLS-related configuration for a managed SAP (MSAP) policy. The values for each entry will be used to populate the following VPLS-related tables when the MSAP policy is applied to a MSAP: TIMETRA-SAP-MIB::sapTlsInfoTable TIMETRA-SAP-MIB::sapTlsDhcpInfoTable ALCATEL-IGMP-SNOOPING-MIB::tlsIgmpSnpgConfigTable | |
| TMN msapTlsPlcyIgmpSnpgFastLeave | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.19 | TmnxEnabledDisabled | read-create | The value of msapTlsPlcyIgmpSnpgFastLeave specifies whether fast leave is allowed on this MSAP. If set to 'enabled', the system prunes the port on which an IGMP 'leave' message has been received without waiting for the Group Specific Query to timeout. |
| U32 msapTlsPlcyIgmpSnpgGenQueryIntv | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.21 | Unsigned32 | read-create | The value of msapTlsPlcyIgmpSnpgGenQueryIntv specifies the interval (in seconds) between two consecutive general queries sent by the system on the MSAP. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is 'enabled'. |
| TPO msapTlsPlcyIgmpSnpgImportPlcy | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.18 | TPolicyStatementNameOrEmpty | read-create | The value of msapTlsPlcyIgmpSnpgImportPlcy specifies the policy statement that is be applied to all incoming IGMP messages on the MSAP. |
| U32 msapTlsPlcyIgmpSnpgLastMembIntvl | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.24 | Unsigned32 | read-create | The value of msapTlsPlcyIgmpSnpgLastMembIntvl specifies the Max Response Time (in tenths of a second) used in Group-Specific and Group-Source-Specific Queries sent in response to 'leave' messages. This is also the amount of time between Group-Specific Query messages. This value may be tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group. |
| U32 msapTlsPlcyIgmpSnpgMaxNbrGrps | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.25 | Unsigned32 | read-create | The value of msapTlsPlcyIgmpSnpgMaxNbrGrps specifies how many group addresses are allowed for the MSAP. The value 0 means that no limit is imposed. |
| TPO msapTlsPlcyIgmpSnpgMcacPlcyName | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.28 | TPolicyStatementNameOrEmpty | read-create | The value of msapTlsPlcyIgmpSnpgMcacPlcyName specifies the name of the multicast CAC (Connection Admission Control) policy. |
| I32 msapTlsPlcyIgmpSnpgMcacPrRsvMnBW | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.30 | Integer32 | read-create | The value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW specifies the bandwidth pre-reserved for all the mandatory channels on a given interface in kilo-bits per second(kbps). If the value of msapTlsPlcyIgmpSnpgMcacUncnstBW is '0', no mandatory channels are allowed. If the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW is '-1', then all mandatory and optional channels are allowed. If the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW is equal to the value of msapTlsPlcyIgmpSnpgMcacUncnstBW, then all the unconstrained bandwidth on a given interface is allocated to mandatory channels configured through multicast CAC policy on that interface and no optional groups (channels) are allowed. The value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW should always be less than or equal to that of msapTlsPlcyIgmpSnpgMcacUncnstBW. An attempt to set the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW greater than that of msapTlsPlcyIgmpSnpgMcacUncnstBW will result in 'inconsistentValue' error. |
| I32 msapTlsPlcyIgmpSnpgMcacUncnstBW | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.29 | Integer32 | read-create | The value of msapTlsPlcyIgmpSnpgMcacUncnstBW specifies the bandwidth assigned for interface's multicast CAC policy traffic in kilo-bits per second(kbps). If the default value of '-1' is set, there is no constraint on bandwidth allocated at the interface. If the value of msapTlsPlcyIgmpSnpgMcacUncnstBW is set to '0' and if a multicast CAC policy is assigned on the interface, then no group (channel) from that policy is allowed on that interface. |
| TMN msapTlsPlcyIgmpSnpgMvrFromVplsId | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.26 | TmnxServId | read-create | The value of msapTlsPlcyIgmpSnpgMvrFromVplsId specifies from which VPLS the multicast streams corresponding to the groups learned via the MSAP are copied. Groups which cannot be joined to the corresponding MVR VPLS (because MVR is not up or the configured MVR policy rejects the group) copy the multicast streams from the local VPLS if IGMP snooping is up (i.e. tlsIgmpSnpgCfgAdminState is 'enabled'). |
| U32 msapTlsPlcyIgmpSnpgQueryRespIntv | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.22 | Unsigned32 | read-create | The value of msapTlsPlcyIgmpSnpgQueryRespIntv specifies the maximum response time (in seconds) advertised in IGMPv2/v3 queries. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is 'enabled'. |
| U32 msapTlsPlcyIgmpSnpgRobustCount | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.23 | Unsigned32 | read-create | The value of msapTlsPlcyIgmpSnpgRobustCount specifies the robustness variable on the MSAP. This object allows tuning for the expected packet loss on the MSAP. If a MSAP is expected to be lossy, the Robustness Variable may be increased. IGMP snooping is robust to (Robustness Variable-1) packet losses. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is 'enabled'. |
| TMN msapTlsPlcyIgmpSnpgSendQueries | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.20 | TmnxEnabledDisabled | read-create | The value of msapTlsPlcyIgmpSnpgSendQueries specifies whether the system generates General Queries by itself on the MSAP. |
| TMN msapTlsPlcyIgmpSnpgVersion | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.27 | TmnxIgmpVersion | read-create | The value of msapTlsPlcyIgmpSnpgVersion specifies the version of IGMP running on the MSAP. |
| TIM msapTlsPlcyLastChanged | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.1 | TimeStamp | read-only | The value of msapTlsPlcyLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| TNA msapTlsPlcySplitHorizonGrp | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.2 | TNamedItemOrEmpty | read-create | The value of msapTlsPlcySplitHorizonGrp specifies the name of the split-horizon group for the MSAP. If the name specified does not correspond to a tlsShgInfoEntry for the VPLS service, the creation of the MSAP will fail. Additionally, if msapTlsPlcySplitHorizonGrp is set to a new value, the sapSplitHorizonGrp object for any existing MSAPs created by this policy will not be updated. |
| T/F msapTlsPlcySubMgmtMacDaHashing | 1.3.6.1.4.1.6527.3.1.2.4.3.45.1.4 | TruthValue | read-create | The value of msapTlsPlcySubMgmtMacDaHashing specifies whether subscriber traffic egressing a LAG MSAP has its egress LAG link selected by a function of the MAC destination address instead of subscriber id. |
| msapTlsPlcyTable | 1.3.6.1.4.1.6527.3.1.2.4.3.45 | not-accessible | The msapTlsPlcyTable has an entry for each managed SAP (MSAP) policy configured in the system. | |
| TIM msapTlsPlcyTblLastChgd | 1.3.6.1.4.1.6527.3.1.2.4.3.60 | TimeStamp | read-only | The value of msapTlsPlcyTblLastChgd indicates the sysUpTime at the time of the last modification of msapTlsPlcyTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| NTF newRootSap | 1.3.6.1.4.1.6527.3.1.3.4.5.0.2 | The newRootSap notification is generated when the previous root bridge has been aged out and a new root bridge has been elected. A new root bridge creates a new spanning tree topology and it may denote loss of customer access or redundancy. Check the new topology against the provisioned topology to determine the severity of connectivity loss. | ||
| NTF receivedTCN | 1.3.6.1.4.1.6527.3.1.3.4.5.0.6 | The receivedTCN notification is generated when a SAP has received TCN from another bridge. This bridge will either have its configured BPDU with the topology change flag set if it is a root bridge, or it will pass TCN to its root bridge. Eventually the address aging timer for the forwarding database will be made shorter for a short period of time. No recovery is needed. | ||
| U32 sapAccountingPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.18 | Unsigned32 | read-create | This object specifies the policy to use to collect accounting statistics on this SAP. The value zero indicates that the agent should use the default accounting policy, if one exists. |
| NTF sapActiveProtocolChange | 1.3.6.1.4.1.6527.3.1.3.4.5.0.30 | The sapActiveProtocolChange notification is generated when the spanning tree protocol on this SAP changes from rstp to stp or vise versa. No recovery is needed. | ||
| SER sapAdminStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.6 | ServiceAdminStatus | read-create | The desired state of this SAP. |
| sapAntiSpoofEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.12.1 | not-accessible | An entry in the sapAntiSpoofTable. | |
| INT sapAntiSpoofing | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.29 | INTEGER | read-create | The value of the object sapAntiSpoofing specifies the type of anti-spoof filtering applicable on this SAP. 'nextHopIpAndMacAddr (4)' is not supported on SR-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '5'. |
| IP sapAntiSpoofIpAddress | 1.3.6.1.4.1.6527.3.1.2.4.3.12.1.1 | IpAddress | read-only | The value of sapAntiSpoofIpAddress indicates the IP address for which this table entry contains information. |
| MAC sapAntiSpoofMacAddress | 1.3.6.1.4.1.6527.3.1.2.4.3.12.1.2 | MacAddress | read-only | The value of sapAntiSpoofMacAddress indicates the MAC address for which this table entry contains information. |
| sapAntiSpoofTable | 1.3.6.1.4.1.6527.3.1.2.4.3.12 | not-accessible | The sapAntiSpoofTable contains information about anti-spoofing filters on a SAP. | |
| ATM sapAtmEgressTrafficDescIndex | 1.3.6.1.4.1.6527.3.1.2.4.3.4.1.3 | AtmTrafficDescrParamIndex | read-write | This object specifies the index of the ATM traffic descriptor in the ATM traffic data encapsulation used in for the egress direction over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification. |
| INT sapAtmEncapsulation | 1.3.6.1.4.1.6527.3.1.2.4.3.4.1.1 | INTEGER | read-write | This object specifies the data encapsulation used over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification. |
| sapAtmInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.4.1 | not-accessible | Information about a specific ATM SAP. | |
| sapAtmInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.4 | not-accessible | A table that contains ATM SAP information. | |
| ATM sapAtmIngressTrafficDescIndex | 1.3.6.1.4.1.6527.3.1.2.4.3.4.1.2 | AtmTrafficDescrParamIndex | read-write | This object specifies the index of the ATM traffic descriptor in the ATM traffic data encapsulation used in for the ingress direction over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification. |
| SER sapAtmOamAlarmCellHandling | 1.3.6.1.4.1.6527.3.1.2.4.3.4.1.4 | ServiceAdminStatus | read-write | A value of up specifies that the OAM status of a pvc affects the sap operational status and OAM AIS/RDI cell generation upon a sap operational status of down. A value of down specifies that the OAM status of a pvc will not affect the operational status of the associated sap and no OAM AIS/RDI cells are generated. |
| SER sapAtmOamPeriodicLoopback | 1.3.6.1.4.1.6527.3.1.2.4.3.4.1.6 | ServiceAdminStatus | read-write | The sapAtmOamPeriodicLoopback object specifies whether this SAP will run periodic OAM loopbacks or not. If enabled, an ATM OAM loopback cell will be transmitted every period as configured in tAtmSysOamLoopbackPeriod. If a response is not received and tAtmSysOamRetryDown consecutive retries also result in failure, the endpoint will transition to the eteAisLoc state. Once in the eteAisLoc state, an ATM OAM loopback cell will be transmitted every period as configured in tAtmSysOamLoopbackPeriod. If a response is received for the periodic loopback and tAtmSysOamRetryUp consecutive retries also each receive a response, the endpoint will transition back to the up state. This object is only configurable on IES or VPRN service endpoints. |
| SER sapAtmOamTerminate | 1.3.6.1.4.1.6527.3.1.2.4.3.4.1.5 | ServiceAdminStatus | read-write | The sapAtmOamTerminate object specifies whether this SAP will act as an OAM termination point. If enabled, OAM cells will be sunk by the SAP and can affect the SAP's operational status (if sapAtmOamAlarmCellHandling is also enabled). Otherwise the OAM cells will be passed into the APIPE service. This object is only configurable for ATM SAPs that are part of an APIPE service SDU or VCC mode. If the sapPortId belongs to an Multi-Chassis APS port, the default value is up. |
| sapBaseInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1 | not-accessible | Information about a specific SAP. | |
| sapBaseInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.2 | not-accessible | A table that contains basic SAP information. | |
| C32 sapBaseStatsAuthenticationPktsDiscarded | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.26 | Counter32 | read-only | The number of DHCP packets discarded as result of authentication. |
| C32 sapBaseStatsAuthenticationPktsSuccess | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.27 | Counter32 | read-only | The number of DHCP packets successfully authenticated. |
| TMN sapBaseStatsCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.23 | TmnxCustId | read-only | The Customer ID for the associated service. |
| C64 sapBaseStatsEgressQchipDroppedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.16 | Counter64 | read-only | The number of in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapBaseStatsEgressQchipDroppedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.15 | Counter64 | read-only | The number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapBaseStatsEgressQchipDroppedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.18 | Counter64 | read-only | The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapBaseStatsEgressQchipDroppedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.17 | Counter64 | read-only | The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapBaseStatsEgressQchipForwardedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.20 | Counter64 | read-only | The number of in-profile octets (rate below CIR) forwarded by the egress Qchip. |
| C64 sapBaseStatsEgressQchipForwardedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.19 | Counter64 | read-only | The number of in-profile packets (rate below CIR) forwarded by the egress Qchip. |
| C64 sapBaseStatsEgressQchipForwardedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.22 | Counter64 | read-only | The number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip. |
| C64 sapBaseStatsEgressQchipForwardedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.21 | Counter64 | read-only | The number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip. |
| sapBaseStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1 | not-accessible | Basic statistics about a specific SAP. | |
| C64 sapBaseStatsIngressPchipDroppedOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.2 | Counter64 | read-only | The number of octets dropped by the ingress Pchip due to: SAP state, ingress MAC, IP or IPv6 filter, same segment discard, bad checksum, etc. |
| C64 sapBaseStatsIngressPchipDroppedPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.1 | Counter64 | read-only | The number of packets dropped by the ingress Pchip due to: SAP state, ingress MAC, IP or IPv6 filter, same segment discard, bad checksum, etc. |
| C64 sapBaseStatsIngressPchipOfferedHiPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.4 | Counter64 | read-only | The number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapBaseStatsIngressPchipOfferedHiPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.3 | Counter64 | read-only | The number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapBaseStatsIngressPchipOfferedLoPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.6 | Counter64 | read-only | The number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapBaseStatsIngressPchipOfferedLoPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.5 | Counter64 | read-only | The number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapBaseStatsIngressPchipOfferedUncoloredOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.25 | Counter64 | read-only | The number of uncolored octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapBaseStatsIngressPchipOfferedUncoloredPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.24 | Counter64 | read-only | The number of uncolored packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapBaseStatsIngressQchipDroppedHiPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.8 | Counter64 | read-only | The number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapBaseStatsIngressQchipDroppedHiPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.7 | Counter64 | read-only | The number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapBaseStatsIngressQchipDroppedLoPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.10 | Counter64 | read-only | The number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapBaseStatsIngressQchipDroppedLoPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.9 | Counter64 | read-only | The number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapBaseStatsIngressQchipForwardedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.12 | Counter64 | read-only | The number of in-profile octets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapBaseStatsIngressQchipForwardedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.11 | Counter64 | read-only | The number of in-profile packets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapBaseStatsIngressQchipForwardedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.14 | Counter64 | read-only | The number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip. |
| C64 sapBaseStatsIngressQchipForwardedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.13 | Counter64 | read-only | The number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip. |
| TIM sapBaseStatsLastClearedTime | 1.3.6.1.4.1.6527.3.1.2.4.3.6.1.28 | TimeStamp | read-only | The value of sapBaseStatsLastClearedTime indicates the sysUpTime when the counters in this table were last cleared. |
| sapBaseStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.6 | not-accessible | A table that contains basic SAP statistics. In the descriptions below 'Pchip' refers to the Alcatel 7x50 SR series Packet Processing chip, while 'Qchip' refers to the Alcatel 7x50 SR series QoS Queueing Engine chip. | |
| U32 sapCemBitrate | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.3 | Unsigned32 | read-only | This object indicates the bit-rate in multiples of 64 Kbit/s of the CEM SAP. |
| TDM sapCemCasTrunkFraming | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.4 | TdmOptionsCasTrunkFraming | read-only | This object indicates the CAS trunk framing mode of the CEM SAP. |
| T/F sapCemDifferential | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.8 | TruthValue | read-only | This object specifies whether this CEM SAP is in differential mode. |
| INT sapCemEndpointType | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.2 | INTEGER | read-only | This object indicates the CEM SAP endpoint type. |
| sapCemInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1 | not-accessible | Information about a specific CEM SAP. | |
| sapCemInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.40 | not-accessible | A table that contains CEM SAP information. | |
| U32 sapCemJitterBuffer | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.6 | Unsigned32 | read-write | This object specifies the jitter buffer size in milliseconds (ms). Default value depends on the CEM SAP endpoint type (sapCemEndpointType), and if applicable, the number of timeslots (sapCemBitrate): --------------------------------------------------------- | Endpoint Type | Timeslots | Default jitter buf. | ---------------------+-----------+----------------------- | 'unstructuredE1' | n/a | 5 ms | ---------------------+-----------+----------------------- | 'unstructuredT1' | n/a | 5 ms | ---------------------+-----------+----------------------- | 'unstructuredE3' | n/a | 5 ms | ---------------------+-----------+----------------------- | 'unstructuredT3' | n/a | 5 ms | ---------------------+-----------+----------------------- | 'nxDS0' (E1/T1) | N = 1 | 32 ms | | +-----------+----------------------- | | N = 2..4 | 16 ms | | +-----------+----------------------- | | N = 5..15 | 8 ms | | +-----------+----------------------- | | N >= 16 | 5 ms | ---------------------+-----------+----------------------- | 'nxDS0WithCas' (E1)| N | 8 ms | ---------------------+-----------+----------------------- | 'nxDS0WithCas' (T1)| N | 12 ms | --------------------------------------------------------- Configuring sapCemPayloadSize and sapCemJitterBuffer to values that result in less than 2 packet buffers or greater than 32 packet buffers is not allowed. The valid range is 1 to 250 ms. Setting this object to 0 sets it back to the default value. |
| TIM sapCemLastMgmtChange | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.1 | TimeStamp | read-only | The value of the object sapCemLastMgmtChange indicates the value of sysUpTime at the time of the most recent management-initiated change to this CEM SAP information. |
| CEM sapCemLocalEcid | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.12 | CemSapEcid | read-write | The value of the object sapCemLocalEcid specifies the local ECID. Only valid if CEM SAP belongs to an EPIPE service. |
| NTF sapCemPacketDefectAlarm | 1.3.6.1.4.1.6527.3.1.3.4.3.0.23 | Generated when a CEM SAP alarm condition is detected. It is generated only when the packet error indicated by 'sapCemReportAlarmStatus' persists over a 3 second window. | ||
| NTF sapCemPacketDefectAlarmClear | 1.3.6.1.4.1.6527.3.1.3.4.3.0.24 | Generated when a CEM SAP alarm condition is cleared. It is generated only when the packet error indicated by 'sapCemReportAlarmStatus' no longer persists over a 10 second window. | ||
| U32 sapCemPayloadSize | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.5 | Unsigned32 | read-write | This object specifies the payload size (in bytes) of packets transmitted to the Packet Service Network (PSN) by the CEM SAP. This determines the size of the data that will be transmitted over the service. As well, if the size of the data received is not consistent with the payload size then the packet is considered malformed. Default value depends on the CEM SAP endpoint type (sapCemEndpointType), and if applicable, the number of timeslots (sapCemBitrate): --------------------------------------------------------- | Endpoint Type | Timeslots | Default payload size | ---------------------+-----------+----------------------- | 'unstructuredE1' | n/a | 256 bytes | ---------------------+-----------+----------------------- | 'unstructuredT1' | n/a | 192 bytes | ---------------------+-----------+----------------------- | 'unstructuredE3' | n/a | 1024 bytes | ---------------------+-----------+----------------------- | 'unstructuredT3' | n/a | 1024 bytes | ---------------------+-----------+----------------------- | 'nxDS0' (E1/T1) | N = 1 | 64 bytes | | +-----------+----------------------- | | N = 2..4 | N x 32 bytes | | +-----------+----------------------- | | N = 5..15 | N x 16 bytes | | +-----------+----------------------- | | N >= 16 | N x 8 bytes | ---------------------+-----------+----------------------- | 'nxDS0WithCas' (E1)| N | N x 16 bytes | ---------------------+-----------+----------------------- | 'nxDS0WithCas' (T1)| N | N x 24 bytes | --------------------------------------------------------- For all endpoint types except for 'nxDS0WithCas', valid payload size range is from the default (in the table above) to 2048 bytes. For 'nxDS0WithCas', sapCemPayloadSize divide by the number of timeslots (sapCemBitrate) must be an integer factor of the number of frames per trunk multiframe (i.e. 16 for E1 trunk and 24 for T1 trunk). For '1xDS0', sapCemPayloadSize must be a multiple of 2. For 'NxDS0', where N > 1, sapCemPayloadSize must be a multiple of the number of timeslots (sapCemBitrate). For 'unstructuredE1', 'unstructuredT1', 'unstructuredE3' and 'unstructuredT3', sapCemPayloadSize must be a multiple of 32 bytes. Configuring sapCemPayloadSize and sapCemJitterBuffer to values that result in less than 2 packet buffers or greater than 32 packet buffer is not allowed. Setting this object to 0 sets it back to the default value. |
| CEM sapCemRemoteEcid | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.14 | CemSapEcid | read-write | The value of the object sapCemRemoteEcid specifies the remote ECID. Only valid if CEM SAP belongs to an EPIPE service. |
| MAC sapCemRemoteMacAddr | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.13 | MacAddress | read-write | The value of the object sapCemRemoteMacAddr specifies the remote MAC address. Only valid if CEM SAP belongs to an EPIPE service. |
| CEM sapCemReportAlarm | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.10 | CemSapReportAlarm | read-write | The value of sapCemReportAlarm determines when and if to generate notifications for the CEM SAP. |
| CEM sapCemReportAlarmStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.11 | CemSapReportAlarm | read-only | The value of sapCemReportAlarmStatus indicates the current alarms on this CEM SAP. |
| C32 sapCemStatsEgressDroppedPkts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.4 | Counter32 | read-only | The value of sapCemStatsEgressDroppedPkts indicates the total number of packets that were dropped due to errors. |
| C32 sapCemStatsEgressESs | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.13 | Counter32 | read-only | The value of sapCemStatsEgressESs indicates the number of Error Seconds (ESs) encountered. Any malformed packet, seq. error, LOPS and similar are considered as error seconds. |
| C32 sapCemStatsEgressFailureCounts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.16 | Counter32 | read-only | The value of sapCemStatsEgressFailureCounts indicates the number failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. |
| C32 sapCemStatsEgressForwardedPkts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.3 | Counter32 | read-only | The value of sapCemStatsEgressForwardedPkts indicates the number of packets that were successfully forwarded. |
| C32 sapCemStatsEgressJtrBfrOverruns | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.8 | Counter32 | read-only | The value of sapCemStatsEgressJtrBfrOverruns indicates the number of times a packet was dropped because it could not fit in the jitter buffer. |
| C32 sapCemStatsEgressJtrBfrUnderruns | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.7 | Counter32 | read-only | The value of sapCemStatsEgressJtrBfrUnderruns indicates the number of times a packet needed to be played out and the jitter buffer was empty. |
| C32 sapCemStatsEgressLBitDropped | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.11 | Counter32 | read-only | The value of sapCemStatsEgressLBitDropped indicates the number of packets dropped due to the L bit set by the far end. |
| C32 sapCemStatsEgressMalformedPkts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.10 | Counter32 | read-only | The value of sapCemStatsEgressMalformedPkts indicates the number of packets detected with unexpected size, or bad headers' stack. |
| C32 sapCemStatsEgressMisOrderDropped | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.9 | Counter32 | read-only | The value of sapCemStatsEgressMisOrderDropped indicates the number of packets detected out of order (via control word sequence numbers), and could not be re-ordered, or could not be placed in the jitter buffer because it was out of the current window. |
| C32 sapCemStatsEgressMissingPkts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.5 | Counter32 | read-only | The value of sapCemStatsEgressMissingPkts indicates the number of missing packets (as detected via control word sequence number gaps). |
| C32 sapCemStatsEgressMultipleDropped | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.12 | Counter32 | read-only | The value of sapCemStatsEgressMultipleDropped indicates the number of packets dropped due to multiple sequence numbers. |
| C32 sapCemStatsEgressOverrunCounts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.18 | Counter32 | read-only | The value of sapCemStatsEgressOverrunCounts indicates the number of times the jitter buffer went into an overrun state. |
| C32 sapCemStatsEgressPktsReOrder | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.6 | Counter32 | read-only | The value of sapCemStatsEgressPktsReOrder indicates the number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. |
| C32 sapCemStatsEgressSESs | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.14 | Counter32 | read-only | The value of sapCemStatsEgressSESs indicates the number of Severely Error Seconds (SESs) encountered. This is when more than 30 percent of the packets within a one second window are missing. |
| C32 sapCemStatsEgressUASs | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.15 | Counter32 | read-only | The value of sapCemStatsEgressUASs indicates the number of Unavailable Seconds (UASs) encountered. Any consecutive ten seconds of SESs are counted as one UAS. |
| C32 sapCemStatsEgressUnderrunCounts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.17 | Counter32 | read-only | The value of sapCemStatsEgressUnderrunCounts indicates the number of times the jitter buffer went into an underrun state. |
| sapCemStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1 | not-accessible | Statistics for a specific CEM SAP. | |
| C32 sapCemStatsIngressDroppedPkts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.2 | Counter32 | read-only | The value of sapCemStatsIngressDroppedPkts indicates the total number of packets that were dropped due to errors. |
| C32 sapCemStatsIngressForwardedPkts | 1.3.6.1.4.1.6527.3.1.2.4.3.41.1.1 | Counter32 | read-only | The value of sapCemStatsIngressForwardedPkts indicates the number of packets that were successfully forwarded. |
| sapCemStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.41 | not-accessible | A table that contains CEM SAP statistics. | |
| U32 sapCemTimestampFreq | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.9 | Unsigned32 | read-only | This object specifies whether the value of the timestamp frequency in multiples of 8 KHz for this CEM SAP. |
| T/F sapCemUseRtpHeader | 1.3.6.1.4.1.6527.3.1.2.4.3.40.1.7 | TruthValue | read-write | This object specifies whether a RTP header is used when packets are transmitted to the Packet Service Network (PSN) by the CEM SAP. |
| T/F sapCollectAcctStats | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.17 | TruthValue | read-create | When the value of this object is 'true' the agent collects accounting statistics on this SAP. |
| T/F sapCpmProtMonitorMac | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.41 | TruthValue | read-create | The value of sapCpmProtMonitorMac specifies whether the tmnxCpmProtPolPerSrcRateLimit of the CPM Protection policy must be applied. If the value of sapCpmProtMonitorMac is 'true', the per-source rate limit must be applied. If the value of sapCpmProtPolicyId is equal to zero (0), the value of sapCpmProtMonitorMac is irrelevant and will be ignored. This object is not supported on SR-1 and ESS-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '5', and 7710, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '7' or '9'. |
| TCP sapCpmProtPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.40 | TCpmProtPolicyID | read-create | The value of sapCpmProtPolicyId associates a CPM Protection policy with a SAP. A value of zero (0) specifies that no CPM Protection policy is associated with this SAP. A value of one (1) specifies that the default CPM Protection policy is associated with this SAP. If no value for sapCpmProtPolicyId is specified when the sapBaseInfoEntry is created, the system assigns a default value as follows: if the system creates a corresponding entry in the sapSubMgmtInfoTable, the default value is 'one'; otherwise, the default value is 'zero'. This means that all SAP's that support Enhanced Subscriber Management get a default value of 'one'. If a SAP would get a default value of 'one', it is not allowed to set the value of sapCpmProtPolicyId to 'zero'. If a SAP would get a default value of 'zero', it is not allowed to modify the value of sapCpmProtPolicyId. This object is not supported on SR-1 and ESS-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '5', and 7710, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '7' or '9'. |
| NTF sapCreated | 1.3.6.1.4.1.6527.3.1.3.4.3.0.1 | This trap is sent when a new row is created in the sapBaseInfoTable. | ||
| TFI sapCurrentEgressIpFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.6 | TFilterID | read-only | The value of the object sapCurrentEgressIpFilterId indicates the index in the tIPFilterTable corresponding to the Egress filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressIpFilterId in case it is overruled by a ToD Suite policy. |
| TFI sapCurrentEgressIpv6FilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.7 | TFilterID | read-only | The value of the object sapCurrentEgressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the Egress Ipv6 filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressIpv6FilterId in case it is overruled by a ToD Suite policy. |
| TFI sapCurrentEgressMacFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.8 | TFilterID | read-only | The value of the object sapCurrentEgressMacFilterId indicates the index in the tMacFilterTable corresponding to the Egress Mac filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressMacFilterId in case it is overruled by a ToD Suite policy. |
| TSA sapCurrentEgressQosPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.9 | TSapEgressPolicyID | read-only | The value of the object sapCurrentEgressQosPolicyId indicates the index in the tSapEgressTable corresponding to the Egress Qos Policy applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressQosPolicyId in case it is overruled by a ToD Suite policy. |
| SER sapCurrentEgressQosSchedPlcy | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.10 | ServObjName | read-only | The value of the object sapCurrentEgressQosSchedPlcy indicates the Egress QoS scheduler on this SAP, or zero if none is currently active. The active policy may deviate from sapEgressQosSchedulerPolicy in case it is overruled by a ToD Suite policy defined on this SAP, or on the multi-customer this SAP belongs to. |
| TFI sapCurrentIngressIpFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.1 | TFilterID | read-only | The value of the object sapCurrentIngressIpFilterId indicates the index in the tIPFilterTable corresponding to the ingress filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressIpFilterId in case it is overruled by a ToD Suite policy. |
| TFI sapCurrentIngressIpv6FilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.2 | TFilterID | read-only | The value of the object sapCurrentIngressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the ingress Ipv6 filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressIpv6FilterId in case it is overruled by a ToD Suite policy. |
| TFI sapCurrentIngressMacFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.3 | TFilterID | read-only | The value of the object sapCurrentIngressMacFilterId indicates the index in the tMacFilterTable corresponding to the ingress Mac filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressMacFilterId in case it is overruled by a ToD Suite policy. |
| TSA sapCurrentIngressQosPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.4 | TSapIngressPolicyID | read-only | The value of the object sapCurrentIngressQosPolicyId indicates the index in the tSapIngressTable corresponding to the ingress Qos Policy applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressQosPolicyId in case it is overruled by a ToD Suite policy. |
| SER sapCurrentIngressQosSchedPlcy | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.5 | ServObjName | read-only | The value of the object sapCurrentIngressQosSchedPlcy indicates the ingress QoS scheduler on this SAP, or zero if none is currently active. The active policy may deviate from sapIngressQosSchedulerPolicy in case it is overruled by a ToD Suite policy defined on this SAP, or on the multi-service this SAP belongs to. |
| TMN sapCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.20 | TmnxCustId | read-only | The Customer ID of the associated service. |
| SER sapCustMultSvcSite | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.21 | ServObjName | read-create | The value of this object, when not null, indicates the Multi-Service Site this SAP is a member of. This information is used to configure the ingress and egress QoS schedulers for this SAP. |
| NTF sapDeleted | 1.3.6.1.4.1.6527.3.1.3.4.3.0.2 | This trap is sent when an existing row is deleted from the sapBaseInfoTable. | ||
| SER sapDescription | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.5 | ServObjDesc | read-create | Generic information about this SAP. |
| NTF sapDHCPCoAError | 1.3.6.1.4.1.6527.3.1.3.4.3.0.19 | The sapDHCPCoAError notification indicates that the system was unable to process a Change of Authorization (CoA) request from a Radius server. | ||
| sapDhcpInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.31.1 | not-accessible | DHCP specific information for a routed CO subscriber SAP. | |
| sapDhcpInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.31 | not-accessible | sapDhcpInfoTable contains DHCP information related to a routed CO subscriber SAP. This table complements sapBaseInfoTable, and contains an entry for each routed CO subscriber SAP. Rows in this table are created and deleted automatically by the system. | |
| NTF sapDHCPLeaseEntriesExceeded | 1.3.6.1.4.1.6527.3.1.3.4.3.0.9 | The sapDHCPLeaseEntriesExceeded notification is generated when the number of DHCP lease state entries on a given SAP reaches a user configurable upper limit. This limit is given by sapTlsDhcpLeasePopulate for a TLS service and by TIMETRA-VRTR-MIB::vRtrIfDHCPLeasePopulate for an IES or VPRN service. | ||
| NTF sapDHCPLseStateMobilityError | 1.3.6.1.4.1.6527.3.1.3.4.3.0.22 | The sapDHCPLseStateMobilityError notification indicates that the system was unable to perform a mobility check for this lease state. | ||
| NTF sapDHCPLseStateOverride | 1.3.6.1.4.1.6527.3.1.3.4.3.0.10 | The sapDHCPLseStateOverride notification is generated when an existing DHCP lease state is overridden by a new lease state which has the same IP address but a different MAC address. | ||
| NTF sapDHCPLseStatePopulateErr | 1.3.6.1.4.1.6527.3.1.3.4.3.0.12 | The sapDHCPLseStatePopulateErr notification indicates that the system was unable to update the DHCP Lease State table with the information contained in the DHCP ACK message. The DHCP ACK message has been discarded. | ||
| U32 sapDhcpOperLeasePopulate | 1.3.6.1.4.1.6527.3.1.2.4.3.31.1.1 | Unsigned32 | read-only | The value of the object sapDhcpOperLeasePopulate indicates the number of DHCP lease states currently allocated on this SAP. |
| NTF sapDHCPProxyServerError | 1.3.6.1.4.1.6527.3.1.3.4.3.0.18 | The sapDHCPProxyServerError notification indicates that the system was unable to proxy DHCP requests. | ||
| NTF sapDHCPSubAuthError | 1.3.6.1.4.1.6527.3.1.3.4.3.0.20 | The sapDHCPSubAuthError notification indicates that the system encountered a problem while trying to authenticate a subscriber. | ||
| NTF sapDHCPSuspiciousPcktRcvd | 1.3.6.1.4.1.6527.3.1.3.4.3.0.11 | The sapDHCPSuspiciousPcktRcvd notification is generated when a DHCP packet is received with suspicious content. | ||
| C64 sapEgQosPlcyDroppedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.3 | Counter64 | read-only | The value of the object sapEgQosPlcyDroppedInProfOctets indicates the number of in-profile octets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgQosPlcyDroppedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.2 | Counter64 | read-only | The value of the object sapEgQosPlcyDroppedInProfPackets indicates the number of in-profile packets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgQosPlcyDroppedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.5 | Counter64 | read-only | The value of the object sapEgQosPlcyDroppedOutProfOctets indicates the number of out-profile octets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgQosPlcyDroppedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.4 | Counter64 | read-only | The value of the object sapEgQosPlcyDroppedOutProfPackets indicates the number of out-profile packets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgQosPlcyForwardedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.7 | Counter64 | read-only | The value of the object sapEgQosPlcyForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the egress Qchip. |
| C64 sapEgQosPlcyForwardedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.6 | Counter64 | read-only | The value of the object sapEgQosPlcyForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the egress Qchip. |
| C64 sapEgQosPlcyForwardedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.9 | Counter64 | read-only | The value of the object sapEgQosPlcyForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip. |
| C64 sapEgQosPlcyForwardedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.8 | Counter64 | read-only | The value of the object sapEgQosPlcyForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip. |
| TSA sapEgQosPlcyId | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1.1 | TSapEgressPolicyID | not-accessible | The value of the object sapEgQosPlcyId indicates the row index in the tSapEgressTable corresponding to this egress QoS policy, or one if no policy is specified. |
| TMN sapEgQosPlcyQueueCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.11 | TmnxCustId | read-only | The value of the object sapEgQosPlcyQueueCustId indicates the Customer ID for the associated service. |
| TSA sapEgQosPlcyQueueId | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.2 | TSapEgrQueueId | not-accessible | The value of sapEgQosPlcyQueueId indicates index of the egress QoS queue of this SAP. |
| TSA sapEgQosPlcyQueuePlcyId | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.1 | TSapEgressPolicyID | not-accessible | The row index in the tSapEgressTable corresponding to this egress QoS policy. |
| C64 sapEgQosPlcyQueueStatsDroppedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.8 | Counter64 | read-only | The value of sapEgQosPlcyQueueStatsDroppedInProfOctets indicates the number in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgQosPlcyQueueStatsDroppedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.4 | Counter64 | read-only | The value of sapEgQosPlcyQueueStatsDroppedInProfPackets indicates the number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgQosPlcyQueueStatsDroppedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.10 | Counter64 | read-only | The value of sapEgQosPlcyQueueStatsDroppedOutProfOctets indicates the number out-of-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgQosPlcyQueueStatsDroppedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.6 | Counter64 | read-only | The value of sapEgQosPlcyQueueStatsDroppedOutProfPackets indicates the number out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgQosPlcyQueueStatsForwardedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.7 | Counter64 | read-only | The value of sapEgQosPlcyQueueStatsForwardedInProfOctets indicates the number ofin-profile octets (rate below CIR) forwarded by the egress Qchip. |
| C64 sapEgQosPlcyQueueStatsForwardedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.3 | Counter64 | read-only | The value of sapEgQosPlcyQueueStatsForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the egress Qchip. |
| C64 sapEgQosPlcyQueueStatsForwardedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.9 | Counter64 | read-only | The value of sapEgQosPlcyQueueStatsForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip. |
| C64 sapEgQosPlcyQueueStatsForwardedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1.5 | Counter64 | read-only | The value of sapEgQosPlcyQueueStatsForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip. |
| TPO sapEgressAggRateLimit | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.35 | TPortSchedulerPIR | read-create | The value of the object sapEgressAggRateLimit specifies the maximum total rate of all egress queues for this SAP. The value '-1' means that there is no limit. |
| T/F sapEgressFrameBasedAccounting | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.42 | TruthValue | read-create | The value of sapEgressFrameBasedAccounting specifies whether to use frame-based accounting when evaluating sapEgressAggRateLimit for all egress queues for this SAP. If the value is 'false', the default packet-based accounting method will be used. |
| TFI sapEgressIpFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.13 | TFilterID | read-create | The row index in the tIPFilterTable corresponding to this egress filter, or zero if no filter is specified. |
| TFI sapEgressIpv6FilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.31 | TFilterID | read-create | The value of the object sapEgressIpv6FilterId specifies the row index in the tIPv6FilterTable corresponding to this egress ipv6 filter, or zero if no ipv6 filter is specified. |
| TFI sapEgressMacFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.12 | TFilterID | read-create | The row index in the tMacFilterTable corresponding to this egress filter, or zero if no filter is specified. |
| T/F sapEgressQinQMarkTopOnly | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.34 | TruthValue | read-create | When the encapsulation type of the access port where this SAP is defined is qinq, the value of the object sapEgressQinQMarkTopOnly specifies which P-bits to mark during packet egress. When the value is false both set of P-bits are marked. When the value is true, only the P-bits in the top Q-tag are marked. |
| TSA sapEgressQosPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.11 | TSapEgressPolicyID | read-create | The row index in the tSapEgressTable corresponding to this egress QoS policy, or one if no policy is specified. |
| SER sapEgressQosSchedulerPolicy | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.23 | ServObjName | read-create | This object can be set only when sapCustMultSvcSite is null. It indicates the egress QoS scheduler for this SAP. |
| TMN sapEgrQosCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.10 | TmnxCustId | read-only | The Customer ID for the associated service. |
| sapEgrQosPlcyQueueStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.30.1 | not-accessible | Egress statistics about a specific SAP's QoS queue for a given Qos policy. | |
| sapEgrQosPlcyQueueStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.30 | not-accessible | A table that contains egress QoS queue SAP statistics per Egress QoS Policy the queue was used by. | |
| sapEgrQosPlcyStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.28.1 | not-accessible | Statistics about a specific Egress Qos Policy applied on a specific SAP. | |
| sapEgrQosPlcyStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.28 | not-accessible | A table that contains Egress Qos policy related statistics for a SAP. | |
| TCI sapEgrQosQAdminCIR | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.11 | TCIRRate | read-create | The value of sapEgrQosQAdminCIR specifies the desired CIR value for this queue. |
| TPI sapEgrQosQAdminPIR | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.10 | TPIRRate | read-create | The value of sapEgrQosQAdminPIR specifies the desired PIR value for this queue. |
| U32 sapEgrQosQAvgOverhead | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.12 | Unsigned32 | read-create | The value of sapEgrQosQAvgOverhead specifies the encapsulation overhead, in hundredths of a percent, used to translate packet-based rate to frame-based rate and vice versa. |
| TBU sapEgrQosQCBS | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.5 | TBurstSize | read-create | The value of sapEgrQosQCBS specifies the amount of reserved buffer space (in kilo bytes) for this queue. |
| TAD sapEgrQosQCIRAdaptation | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.8 | TAdaptationRule | read-create | The value of sapEgrQosQCIRAdaptation specifies the criteria to use to compute the operational CIR value for this queue, while maintaining a minimum offset. |
| TBU sapEgrQosQHiPrioOnly | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.7 | TBurstPercentOrDefault | read-create | The value of sapEgrQosQHiPrioOnly specifies the percentage of buffer space for this queue, used exclusively by high priority packets. |
| TEG sapEgrQosQId | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.1 | TEgressQueueId | not-accessible | The value of sapEgrQosQId indicates the ID of the queue whose parameters are to be overridden. |
| TIM sapEgrQosQLastMgmtChange | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.3 | TimeStamp | read-only | The value of sapEgrQosQLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row. |
| TBU sapEgrQosQMBS | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.6 | TBurstSize | read-create | The value of sapEgrQosQMBS specifies the maximum amount of buffer space (in kilo bytes) allowed for this queue. |
| TQO sapEgrQosQOverrideFlags | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.4 | TQosQueueAttribute | read-create | The value of sapEgrQosQOverrideFlags specifies the set of attributes whose values have been overridden via management on this queue. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAP's ingress QoS policy. |
| TAD sapEgrQosQPIRAdaptation | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.9 | TAdaptationRule | read-create | The value of sapEgrQosQPIRAdaptation specifies the criteria to use to compute the operational PIR value for this queue, while maintaining a minimum offset. |
| ROW sapEgrQosQRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1.2 | RowStatus | read-create | The value of sapEgrQosQRowStatus controls the creation and deletion of rows in this table. |
| TSA sapEgrQosQueueId | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.1 | TSapEgrQueueId | read-only | The index of the egress QoS queue of this SAP. |
| sapEgrQosQueueInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.20.1 | not-accessible | Override values for the specified SAP egress QoS queue. These values override the corresponding ones specified in the associated SAP egress QoS policy. | |
| sapEgrQosQueueInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.20 | not-accessible | This table is used to override the base parameters of a queue, as defined in the associated SAP egress QoS policy. | |
| C64 sapEgrQosQueueStatsDroppedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.7 | Counter64 | read-only | The number of in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgrQosQueueStatsDroppedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.3 | Counter64 | read-only | The number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgrQosQueueStatsDroppedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.9 | Counter64 | read-only | The number of out-of-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapEgrQosQueueStatsDroppedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.5 | Counter64 | read-only | The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| sapEgrQosQueueStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1 | not-accessible | Egress statistics about a specific SAP's QoS queue. | |
| C64 sapEgrQosQueueStatsForwardedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.6 | Counter64 | read-only | The number of in-profile octets (rate below CIR) forwarded by the egress Qchip. |
| C64 sapEgrQosQueueStatsForwardedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.2 | Counter64 | read-only | The number of in-profile packets (rate below CIR) forwarded by the egress Qchip. |
| C64 sapEgrQosQueueStatsForwardedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.8 | Counter64 | read-only | The number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip. |
| C64 sapEgrQosQueueStatsForwardedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.8.1.4 | Counter64 | read-only | The number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip. |
| sapEgrQosQueueStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.8 | not-accessible | A table that contains egress QoS queue SAP statistics. | |
| TMN sapEgrQosSchedCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.10.1.4 | TmnxCustId | read-only | The Customer ID for the associated service. |
| sapEgrQosSchedInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.22.1 | not-accessible | Override values for the specified SAP egress virtual scheduler. These values override the corresponding ones specified in the associated SAP egress scheduler policy. | |
| sapEgrQosSchedInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.22 | not-accessible | This table is used to override the base parameters of a virtual scheduler, as defined in the associated SAP egress scheduler policy. | |
| TNA sapEgrQosSchedName | 1.3.6.1.4.1.6527.3.1.2.4.3.10.1.1 | TNamedItem | not-accessible | The index of the egress QoS scheduler of this SAP. |
| sapEgrQosSchedStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.10.1 | not-accessible | Egress statistics about a specific SAP's QoS queue. | |
| C64 sapEgrQosSchedStatsForwardedOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.10.1.3 | Counter64 | read-only | The number of forwarded octets by the egress Qchip, as determined by the SAP egress scheduler policy. |
| C64 sapEgrQosSchedStatsForwardedPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.10.1.2 | Counter64 | read-only | The number of forwarded packets by the egress Qchip, as determined by the SAP egress scheduler policy. |
| sapEgrQosSchedStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.10 | not-accessible | A table that contains ingress QoS queue SAP statistics. | |
| TCI sapEgrQosSCIR | 1.3.6.1.4.1.6527.3.1.2.4.3.22.1.6 | TCIRRate | read-create | The value of sapEgrQosSCIR specifies the desired CIR value for this virtual scheduler. |
| TIM sapEgrQosSLastMgmtChange | 1.3.6.1.4.1.6527.3.1.2.4.3.22.1.3 | TimeStamp | read-only | The value of sapEgrQosSLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row. |
| TNA sapEgrQosSName | 1.3.6.1.4.1.6527.3.1.2.4.3.22.1.1 | TNamedItem | not-accessible | The value of sapEgrQosSName indicates the name of the virtual scheduler whose parameters are to be overridden. |
| TVI sapEgrQosSOverrideFlags | 1.3.6.1.4.1.6527.3.1.2.4.3.22.1.4 | TVirtSchedAttribute | read-create | The value of sapEgrQosSOverrideFlags specifies the set of attributes whose values have been overridden via management on this virtual scheduler. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAP's egress scheduler policy. |
| TPI sapEgrQosSPIR | 1.3.6.1.4.1.6527.3.1.2.4.3.22.1.5 | TPIRRate | read-create | The value of sapEgrQosSPIR specifies the desired PIR value for this virtual scheduler. |
| ROW sapEgrQosSRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.22.1.2 | RowStatus | read-create | The value of sapEgrQosSRowStatus controls the creation and deletion of rows in this table. |
| T/F sapEgrQosSSummedCIR | 1.3.6.1.4.1.6527.3.1.2.4.3.22.1.7 | TruthValue | read-create | The value of sapEgrQosSSummedCIR specifies if the CIR should be used as the summed CIR values of the children schedulers or queues. If set to 'true', the applicable scheduler CIR (sapEgrQosSCIR) loses its meaning. |
| sapEgrSchedPlcyPortStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.35.1 | not-accessible | Statistics about a specific SAP's egress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies. | |
| C64 sapEgrSchedPlcyPortStatsFwdOct | 1.3.6.1.4.1.6527.3.1.2.4.3.35.1.3 | Counter64 | read-only | The value of sapEgrSchedPlcyPortStatsFwdOct indicates the number of forwarded octets,as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip. |
| C64 sapEgrSchedPlcyPortStatsFwdPkt | 1.3.6.1.4.1.6527.3.1.2.4.3.35.1.2 | Counter64 | read-only | The value of sapEgrSchedPlcyPortStatsFwdPkt indicates the number of forwarded packets, as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip. |
| TMN sapEgrSchedPlcyPortStatsPort | 1.3.6.1.4.1.6527.3.1.2.4.3.35.1.1 | TmnxPortID | not-accessible | The value of sapEgrSchedPlcyPortStatsPort is used as an index of the egress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in 'link' mode, this object is the TmnxPortID of the member-port on which the scheduler is applied. |
| sapEgrSchedPlcyPortStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.35 | not-accessible | The sapEgrSchedPlcyPortStatsTable contains egress QoS scheduler statistics for the SAP's, organized per scheduler policy and per port. This table is used when the SAP is a CCAG or LAG in 'link' mode, or an APS. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies. | |
| sapEgrSchedPlcyStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.33.1 | not-accessible | Statistics about a specific SAP's egress QoS scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies. | |
| C64 sapEgrSchedPlcyStatsFwdOct | 1.3.6.1.4.1.6527.3.1.2.4.3.33.1.2 | Counter64 | read-only | The number of octets forwarded by the egress Qchip, as determined by the SAP egress scheduler policy. |
| C64 sapEgrSchedPlcyStatsFwdPkt | 1.3.6.1.4.1.6527.3.1.2.4.3.33.1.1 | Counter64 | read-only | The number of packets forwarded by the egress Qchip, as determined by the SAP egress scheduler policy. |
| sapEgrSchedPlcyStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.33 | not-accessible | A table that contains egress QoS scheduler statistics for the SAP's, organized by scheduler policy. | |
| NTF sapEncapDot1d | 1.3.6.1.4.1.6527.3.1.3.4.5.0.12 | The sapEncapDot1d notification is generated when the SAP receives a BPDU that is 802.1d encapsulated after having received BPDUs that were PVST encapsulated. The SAP BPDUs will also be 802.1d encapsulated. No recovery is needed. | ||
| NTF sapEncapPVST | 1.3.6.1.4.1.6527.3.1.3.4.5.0.11 | The sapEncapPVST notification is generated when the SAP receives a BPDU that is PVST encapsulated, after having received BPDUs that were 802.d encapsulated. The SAP BPDUs will also be PVST encapsulated. No recovery is needed. | ||
| TMN sapEncapValue | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.2 | TmnxEncapVal | read-only | The value of the label used to identify this SAP on the access port specified by sapPortId. |
| SER sapEndPoint | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.36 | ServObjName | read-create | The value of the object sapEndPoint specifies the service endpoint to which this SAP is attached. The svcId of the SAP MUST match the svcId of the service endpoint. |
| sapEthernetInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.43.1 | not-accessible | Information about a specific Ethernet SAP. | |
| sapEthernetInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.43 | not-accessible | A table that contains Ethernet SAP information. | |
| SER sapEthernetLLFAdminStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.43.1.1 | ServiceAdminStatus | read-create | sapEthernetLLFAdminStatus specifies whether or not Link- Loss Forwarding is enabled ('up'). When this object is set to 'up' the underlying port will be forced into the operationally 'down' state if the service is operationally 'down', or any of the 'sdpBindPwPeerStatusBits' are set, and will set the underlying port's tmnxPortEtherReasonDownFlags 'linklossFwd' bit. Setting this object to 'down' will clear the 'linklossFwd' reason. sapEthernetLLFAdminStatus can only be enabled on saps configured for an EPIPE service using an Ethernet port with the tmnxPortEncapType set to 'nullEncap.' |
| INT sapEthernetLLFOperStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.43.1.2 | INTEGER | read-only | sapEthernetLLFOperStatus indicates whether or not the underlying port is forced operationally 'down' due to the service being operationally 'down' or an sdpBindPwPeerStatusBits bit is set. sapEthernetLLFOperStatus is set to 'fault' when the sapEthernetLLFAdminStatus is set to 'up,' and either a fault has occurred on the pseudo-wire, or the service is down, otherwise sapEthernetLLFOperStatus is set to 'clear.' |
| NUM sapIesIfIndex | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.15 | InterfaceIndexOrZero | read-create | When the value of sapType is 'ies' this object specifies the index of the IES interface where this SAP is defined. The value of this object can be set only when the row is created and cannot be changed while the row status is 'active'. This object is otherwise not significant and should have the value zero. |
| C64 sapIgQosPlcyDroppedHiPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.3 | Counter64 | read-only | The value of the object sapIgQosPlcyDroppedHiPrioOctets indicates the number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIgQosPlcyDroppedHiPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.2 | Counter64 | read-only | The value of the object sapIgQosPlcyDroppedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIgQosPlcyDroppedLoPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.5 | Counter64 | read-only | The value of the object sapIgQosPlcyDroppedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIgQosPlcyDroppedLoPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.4 | Counter64 | read-only | The value of the object sapIgQosPlcyDroppedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIgQosPlcyForwardedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.7 | Counter64 | read-only | The value of the object sapIgQosPlcyForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapIgQosPlcyForwardedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.6 | Counter64 | read-only | The value of the object sapIgQosPlcyForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapIgQosPlcyForwardedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.9 | Counter64 | read-only | The value of the object sapIgQosPlcyForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip. |
| C64 sapIgQosPlcyForwardedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.8 | Counter64 | read-only | The value of the object sapIgQosPlcyForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip. |
| TSA sapIgQosPlcyId | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1.1 | TSapIngressPolicyID | not-accessible | The value of the object sapIgQosPlcyId indicates the row index in the tSapIngressTable corresponding to this ingress QoS policy, or one if no policy is specified. |
| TMN sapIgQosPlcyQueueCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.15 | TmnxCustId | read-only | The value of the object sapIgQosPlcyQueueCustId indicates the Customer ID for the associated service. |
| TSA sapIgQosPlcyQueueId | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.2 | TSapIngQueueId | not-accessible | The index of the ingress QoS queue of this SAP used by the policy indicated by sapIgQosPlcyQueuePlcyId. |
| TSA sapIgQosPlcyQueuePlcyId | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.1 | TSapIngressPolicyID | not-accessible | The value of the object sapIgQosPlcyQueuePlcyId indicates the row index in the tSapIngressTable corresponding to this ingress QoS policy. |
| C64 sapIgQosPlcyQueueStatsDroppedHiPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.8 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsDroppedHiPrioOctets indicates the number ofhigh priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIgQosPlcyQueueStatsDroppedHiPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.4 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsDroppedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIgQosPlcyQueueStatsDroppedLoPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.10 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsDroppedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIgQosPlcyQueueStatsDroppedLoPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.6 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsDroppedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIgQosPlcyQueueStatsForwardedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.13 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapIgQosPlcyQueueStatsForwardedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.11 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapIgQosPlcyQueueStatsForwardedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.14 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip. |
| C64 sapIgQosPlcyQueueStatsForwardedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.12 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip. |
| C64 sapIgQosPlcyQueueStatsOfferedHiPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.7 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsOfferedHiPrioOctets indicates the number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapIgQosPlcyQueueStatsOfferedHiPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.3 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsOfferedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapIgQosPlcyQueueStatsOfferedLoPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.9 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsOfferedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapIgQosPlcyQueueStatsOfferedLoPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.5 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsOfferedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapIgQosPlcyQueueStatsUncoloredOctetsOffered | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.17 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsUncoloredOctetsOffered indicates the number of uncolored octets offered to the ingress Qchip. |
| C64 sapIgQosPlcyQueueStatsUncoloredPacketsOffered | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1.16 | Counter64 | read-only | The value of sapIgQosPlcyQueueStatsUncoloredPacketsOffered indicates the number of uncolored packets offered to the ingress Qchip. |
| TMN sapIngQosCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.14 | TmnxCustId | read-only | The Customer ID for the associated service. |
| sapIngQosPlcyQueueStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.29.1 | not-accessible | Ingress statistics about a specific SAP's QoS queue for a given Qos policy. | |
| sapIngQosPlcyQueueStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.29 | not-accessible | A table that contains ingress QoS queue SAP statistics, per Ingress QoS Policy the queue was used by. | |
| TCI sapIngQosQAdminCIR | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.11 | TCIRRate | read-create | The value of sapIngQosQAdminCIR specifies the desired CIR value for this queue. |
| TPI sapIngQosQAdminPIR | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.10 | TPIRRate | read-create | The value of sapIngQosQAdminPIR specifies the desired PIR value for this queue. |
| TBU sapIngQosQCBS | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.5 | TBurstSize | read-create | The value of sapIngQosQCBS specifies the amount of reserved buffer space (in kilo bytes) for this queue. |
| TAD sapIngQosQCIRAdaptation | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.8 | TAdaptationRule | read-create | The value of sapIngQosQCIRAdaptation specifies the criteria to use to compute the operational CIR value for this queue, while maintaining a minimum offset. |
| TBU sapIngQosQHiPrioOnly | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.7 | TBurstPercentOrDefault | read-create | The value of sapIngQosQHiPrioOnly specifies the percentage of buffer space for this queue, used exclusively by high priority packets. |
| TIN sapIngQosQId | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.1 | TIngressQueueId | not-accessible | The value of sapIngQosQId indicates the ID of the queue whose parameters are to be overridden. |
| TIM sapIngQosQLastMgmtChange | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.3 | TimeStamp | read-only | The value of sapIngQosQLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row. |
| TBU sapIngQosQMBS | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.6 | TBurstSize | read-create | The value of sapIngQosQMBS specifies the maximum amount of buffer space (in kilo bytes) allowed for this queue. |
| TQO sapIngQosQOverrideFlags | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.4 | TQosQueueAttribute | read-create | The value of sapIngQosQOverrideFlags specifies the set of attributes whose values have been overridden via management on this queue. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAP's ingress QoS policy. |
| TAD sapIngQosQPIRAdaptation | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.9 | TAdaptationRule | read-create | The value of sapIngQosQPIRAdaptation specifies the criteria to use to compute the operational PIR value for this queue, while maintaining a minimum offset. |
| ROW sapIngQosQRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1.2 | RowStatus | read-create | The value of sapIngQosQRowStatus controls the creation and deletion of rows in this table. |
| TSA sapIngQosQueueId | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.1 | TSapIngQueueId | read-only | The index of the ingress QoS queue of this SAP. |
| sapIngQosQueueInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.19.1 | not-accessible | Override values for the specified SAP ingress QoS queue. These values override the corresponding ones specified in the associated SAP ingress QoS policy. | |
| sapIngQosQueueInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.19 | not-accessible | This table is used to override the base parameters of a queue, as defined in the associated SAP ingress QoS policy. | |
| C64 sapIngQosQueueStatsDroppedHiPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.7 | Counter64 | read-only | The number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIngQosQueueStatsDroppedHiPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.3 | Counter64 | read-only | The number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIngQosQueueStatsDroppedLoPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.9 | Counter64 | read-only | The number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| C64 sapIngQosQueueStatsDroppedLoPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.5 | Counter64 | read-only | The number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
| sapIngQosQueueStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1 | not-accessible | Ingress statistics about a specific SAP's QoS queue. | |
| C64 sapIngQosQueueStatsForwardedInProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.12 | Counter64 | read-only | The number of in-profile octets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapIngQosQueueStatsForwardedInProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.10 | Counter64 | read-only | The number of in-profile packets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapIngQosQueueStatsForwardedOutProfOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.13 | Counter64 | read-only | The number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip. |
| C64 sapIngQosQueueStatsForwardedOutProfPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.11 | Counter64 | read-only | The number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip. |
| C64 sapIngQosQueueStatsOfferedHiPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.6 | Counter64 | read-only | The number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapIngQosQueueStatsOfferedHiPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.2 | Counter64 | read-only | The number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapIngQosQueueStatsOfferedLoPrioOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.8 | Counter64 | read-only | The number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| C64 sapIngQosQueueStatsOfferedLoPrioPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.4 | Counter64 | read-only | The number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
| sapIngQosQueueStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.7 | not-accessible | A table that contains ingress QoS queue SAP statistics. | |
| C64 sapIngQosQueueStatsUncoloredOctetsOffered | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.16 | Counter64 | read-only | The number of uncolored octets offered to the ingress Qchip. |
| C64 sapIngQosQueueStatsUncoloredPacketsOffered | 1.3.6.1.4.1.6527.3.1.2.4.3.7.1.15 | Counter64 | read-only | The number of uncolored packets offered to the ingress Qchip. |
| TMN sapIngQosSchedCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.9.1.4 | TmnxCustId | read-only | The Customer ID for the associated service. |
| sapIngQosSchedInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.21.1 | not-accessible | Override values for the specified SAP ingress virtual scheduler. These values override the corresponding ones specified in the associated SAP ingress scheduler policy. | |
| sapIngQosSchedInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.21 | not-accessible | This table is used to override the base parameters of a virtual scheduler, as defined in the associated SAP ingress scheduler policy. | |
| TNA sapIngQosSchedName | 1.3.6.1.4.1.6527.3.1.2.4.3.9.1.1 | TNamedItem | not-accessible | The index of the ingress QoS scheduler of this SAP. |
| sapIngQosSchedStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.9.1 | not-accessible | Ingress statistics about a specific SAP's QoS queue. | |
| C64 sapIngQosSchedStatsForwardedOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.9.1.3 | Counter64 | read-only | The number of forwarded octets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip. |
| C64 sapIngQosSchedStatsForwardedPackets | 1.3.6.1.4.1.6527.3.1.2.4.3.9.1.2 | Counter64 | read-only | The number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip. |
| sapIngQosSchedStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.9 | not-accessible | A table that contains ingress QoS queue SAP statistics. | |
| TCI sapIngQosSCIR | 1.3.6.1.4.1.6527.3.1.2.4.3.21.1.6 | TCIRRate | read-create | The value of sapIngQosSCIR specifies the desired CIR value for this virtual scheduler. |
| TIM sapIngQosSLastMgmtChange | 1.3.6.1.4.1.6527.3.1.2.4.3.21.1.3 | TimeStamp | read-only | The value of sapIngQosSLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row. |
| TNA sapIngQosSName | 1.3.6.1.4.1.6527.3.1.2.4.3.21.1.1 | TNamedItem | not-accessible | The value of sapIngQosSName indicates the name of the virtual scheduler whose parameters are to be overridden. |
| TVI sapIngQosSOverrideFlags | 1.3.6.1.4.1.6527.3.1.2.4.3.21.1.4 | TVirtSchedAttribute | read-create | The value of sapIngQosSOverrideFlags specifies the set of attributes whose values have been overridden via management on this virtual scheduler. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAP's ingress scheduler policy. |
| TPI sapIngQosSPIR | 1.3.6.1.4.1.6527.3.1.2.4.3.21.1.5 | TPIRRate | read-create | The value of sapIngQosSPIR specifies the desired PIR value for this virtual scheduler. |
| ROW sapIngQosSRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.21.1.2 | RowStatus | read-create | The value of sapIngQosSRowStatus controls the creation and deletion of rows in this table. |
| T/F sapIngQosSSummedCIR | 1.3.6.1.4.1.6527.3.1.2.4.3.21.1.7 | TruthValue | read-create | The value of sapIngQosSSummedCIR specifies if the CIR should be used as the summed CIR values of the children schedulers or queues. If set to 'true', the applicable scheduler CIR (sapIngQosSCIR) loses its meaning. |
| TFI sapIngressIpFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.10 | TFilterID | read-create | The value of the object sapIngressIpFilterId specifies the row index in the tIPFilterTable corresponding to this ingress filter, or zero if no filter is specified. |
| TFI sapIngressIpv6FilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.30 | TFilterID | read-create | The value of the object sapIngressIpv6FilterId specifies the row index in the tIPv6FilterTable corresponding to this ingress ipv6 filter, or zero if no ipv6 filter is specified. |
| TFI sapIngressMacFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.9 | TFilterID | read-create | The value of the object sapIngressMacFilterId specifies the row index in the tMacFilterTable corresponding to this ingress filter, or zero if no filter is specified. |
| INT sapIngressMatchQinQDot1PBits | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.26 | INTEGER | read-create | This object applies only to SAP's defined on a port configured for qinq service encapsulation. It indicates which 802.1P bits will be used to match a QoS or a MAC filter policy when a double-tagged frame is received on this SAP. |
| TSA sapIngressQosPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.8 | TSapIngressPolicyID | read-create | The value of the object sapIngressQosPolicyId specifies the row index in the tSapIngressTable corresponding to this ingress QoS policy, or one if no policy is specified. The value 0 is needed for mirror SAPs that cannot have a qos policy assigned. |
| SER sapIngressQosSchedulerPolicy | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.22 | ServObjName | read-create | This object can be set only when sapCustMultSvcSite is null. It indicates the ingress QoS scheduler for this SAP. |
| SER sapIngressSharedQueuePolicy | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.25 | ServObjName | read-create | This object indicates the ingress shared queue policy used by this SAP. When the value of this object is null it means that the SAP will use individual ingress QoS queues, instead of the shared ones. |
| INT sapIngressVlanTranslation | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.37 | INTEGER | read-create | The value of sapIngressVlanTranslation specifies the desired Ingress Vlan Translation. A value of 'vlanId' specifies that the value of sapIngressVlanTranslationId is to be used to overwrite the preserved VLAN id in the packet. A value of 'copyOuter' specifies that the outer VLAN id should be used to overwrite the preserved VLAN id in the packet. An 'inconsistentValue' error is returned when an attempt is made to set the value of sapIngressVlanTranslation to 'vlanId' and sapIngressVlanTranslationId is set to '-1'. |
| I32 sapIngressVlanTranslationId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.38 | Integer32 | read-create | The value of sapIngressVlanTranslationId specifies the VLAN id to be used to overwrite the preserved VLAN id in the packet. An 'inconsistentValue' error is returned when an attempt is made to set the value of sapIngressVlanTranslationId to other than '-1' and sapIngressVlanTranslation is not set to 'vlanId'. |
| sapIngrQosPlcyStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.27.1 | not-accessible | Statistics about a specific Ingress Qos Policy applied on a specific SAP. | |
| sapIngrQosPlcyStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.27 | not-accessible | A table that contains Ingress Qos policy related statistics for a SAP. | |
| sapIngSchedPlcyPortStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.34.1 | not-accessible | Statistics about a specific SAP's ingress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies. | |
| C64 sapIngSchedPlcyPortStatsFwdOct | 1.3.6.1.4.1.6527.3.1.2.4.3.34.1.3 | Counter64 | read-only | The value of sapIngSchedPlcyPortStatsFwdOct indicates the number of forwarded octets,as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip. |
| C64 sapIngSchedPlcyPortStatsFwdPkt | 1.3.6.1.4.1.6527.3.1.2.4.3.34.1.2 | Counter64 | read-only | The value of sapIngSchedPlcyPortStatsFwdPkt indicates the number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip. |
| TMN sapIngSchedPlcyPortStatsPort | 1.3.6.1.4.1.6527.3.1.2.4.3.34.1.1 | TmnxPortID | not-accessible | The value of sapIngSchedPlcyPortStatsPort is used as an index of the ingress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in 'link' mode, this object is the TmnxPortID of the member-port on which the scheduler is applied. |
| sapIngSchedPlcyPortStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.34 | not-accessible | The sapIngSchedPlcyPortStatsTable contains ingress QoS scheduler statistics for the SAP's, organized per scheduler policy and per port. This table is used when the SAP is a CCAG or LAG in 'link' mode, or an APS. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies. | |
| sapIngSchedPlcyStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.32.1 | not-accessible | Statistics about a specific SAP's ingress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies. | |
| C64 sapIngSchedPlcyStatsFwdOct | 1.3.6.1.4.1.6527.3.1.2.4.3.32.1.2 | Counter64 | read-only | The number of forwarded octets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip. |
| C64 sapIngSchedPlcyStatsFwdPkt | 1.3.6.1.4.1.6527.3.1.2.4.3.32.1.1 | Counter64 | read-only | The number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip. |
| sapIngSchedPlcyStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.32 | not-accessible | A table that contains ingress QoS queue statistics for the SAP's, organized by scheduler policy. | |
| T/F sapIngUseMultipointShared | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.33 | TruthValue | read-create | When the value of sapIngressSharedQueuePolicy is not null, the value of the object sapIngUseMultipointShared specifies whether this SAP uses the multipoint-shared queues of the shared policy. |
| TFI sapIntendedEgressIpFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.16 | TFilterID | read-only | The value of the object sapIntendedEgressIpFilterId indicates the index in the tIPFilterTable corresponding to the Egress IP filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressIpFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| TFI sapIntendedEgressIpv6FilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.17 | TFilterID | read-only | The value of the object sapIntendedEgressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the Egress IPv6 filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressIpv6FilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| TFI sapIntendedEgressMacFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.18 | TFilterID | read-only | The value of the object sapIntendedEgressMacFilterId indicates the index in the tMacFilterTable corresponding to the Egress mac filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressMacFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| TSA sapIntendedEgressQosPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.19 | TSapEgressPolicyID | read-only | The value of the object sapIntendedEgressQosPolicyId indicates the index in the tSapEgressTable corresponding to the Egress Qos Policy that should be applied on this SAP. If it deviates from sapCurrentEgressQosPolicyId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| SER sapIntendedEgressQosSchedPlcy | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.20 | ServObjName | read-only | The value of the object sapIntendedEgressQosSchedPlcy indicates the index in the tSapEgressTable corresponding to the Egress Qos Scheduler policy that should be applied on this SAP. If it deviates from sapCurrentEgressQosSchedPlcy, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| TFI sapIntendedIngressIpFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.11 | TFilterID | read-only | The value of the object sapIntendedIngressIpFilterId indicates the index in the tIPFilterTable corresponding to the ingress IP filter that should be applied on this SAP. If it deviates from sapCurrentIngressIpFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| TFI sapIntendedIngressIpv6FilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.12 | TFilterID | read-only | The value of the object sapIntendedIngressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the ingress Ipv6 filter that should be applied on this SAP. If it deviates from sapCurrentIngressIpv6FilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| TFI sapIntendedIngressMacFilterId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.13 | TFilterID | read-only | The value of the object sapIntendedIngressMacFilterId indicates the index in the tMacFilterTable corresponding to the ingress Mac filter that should be applied on this SAP. If it deviates from sapCurrentIngressMacFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| TSA sapIntendedIngressQosPolicyId | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.14 | TSapIngressPolicyID | read-only | The value of the object sapIntendedIngressQosPolicyId indicates the index in the tSapIngressTable corresponding to the ingress Qos policy that should be applied on this SAP. If it deviates from sapCurrentIngressQosPolicyId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| SER sapIntendedIngressQosSchedPlcy | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1.15 | ServObjName | read-only | The value of the object sapIntendedIngressQosSchedPlcy indicates the ingress QoS scheduler that should be applied on this SAP. If it deviates from sapCurrentIngressQosSchedPlcy, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal. |
| MAC sapIpipeArpedMacAddress | 1.3.6.1.4.1.6527.3.1.2.4.3.25.1.5 | MacAddress | read-only | The value of the object sapIpipeArpedMacAddress indicates the MAC address of the local end host. |
| U32 sapIpipeArpedMacAddressTimeout | 1.3.6.1.4.1.6527.3.1.2.4.3.25.1.6 | Unsigned32 | read-only | The value of the object sapIpipeArpedMacAddressTimeout indicates the number of seconds to wait for the sapIpipeArpedMacAddress to be re-refreshed. |
| IP sapIpipeCeInetAddress | 1.3.6.1.4.1.6527.3.1.2.4.3.25.1.2 | InetAddress | read-write | The type of this address is determined by the value of the sapIpipeCeInetAddressType object. This object specifies the IPv4 address of the local end host of an IPIPE. |
| IPt sapIpipeCeInetAddressType | 1.3.6.1.4.1.6527.3.1.2.4.3.25.1.1 | InetAddressType | read-write | The value of the object sapIpipeCeInetAddressType specifies the addresstype of the local end host IP of an IPIPE. |
| sapIpipeInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.25.1 | not-accessible | IPIPE specific information about a SAP. | |
| sapIpipeInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.25 | not-accessible | A table that contains IPIPE specific SAP information. | |
| MAC sapIpipeMacAddress | 1.3.6.1.4.1.6527.3.1.2.4.3.25.1.4 | MacAddress | read-write | The value of the object sapIpipeMacAddress specifies the MAC address of an IPIPE Ethernet SAP. |
| U32 sapIpipeMacRefreshInterval | 1.3.6.1.4.1.6527.3.1.2.4.3.25.1.3 | Unsigned32 | read-write | The value of sapIpipeMacRefreshInterval specifies the interval between successive attempts to refresh the MAC address of the CE device associated with an Ethernet ipipe SAP. If no other event (such as reception of an ARP request from the CE) occurs that would refresh the MAC address before the end of the interval, an ARP request will be originated from the IPIPE SAP. |
| TIM sapLastMgmtChange | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.16 | TimeStamp | read-only | The value of sysUpTime at the time of the most recent management-initiated change to this SAP. |
| TIM sapLastStatusChange | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.28 | TimeStamp | read-only | The value of sysUpTime at the time of the most recent operating status change to this SAP. |
| INT sapMirrorStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.14 | INTEGER | read-only | This object specifies whether traffic mirroring has been enabled on this SAP. |
| TMN sapNotifyPortId | 1.3.6.1.4.1.6527.3.1.2.4.3.100.1 | TmnxPortID | accessible-for-notify | The ID of the access port where a SAP is defined. This object is used by the sapPortStateChangeProcessed notification to indicate the port ID that changed state and that resulted in having the associated sapStatusChanged events suppressed for all SAPs on that port. |
| I32 sapNumEntriesEx | 1.3.6.1.4.1.6527.3.1.2.4.3.1 | Integer32 | read-only | The current number of SAPs configured in this device. |
| BIT sapOperFlags | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.27 | Bits | read-only | This object specifies all the conditions that affect the operating status of this SAP. |
| INT sapOperStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.7 | INTEGER | read-only | The value of the object sapOperStatus indicates the operating state of this SAP. |
| TMN sapPortId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.1 | TmnxPortID | read-only | The ID of the access port where this SAP is defined. |
| TMN sapPortIdEgrPortId | 1.3.6.1.4.1.6527.3.1.2.4.3.18.1.2 | TmnxPortID | not-accessible | The value of sapPortIdEgrPortId is used as an index of the egress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in 'link' mode, this object is the TmnxPortID of the member-port on which the scheduler is applied. |
| TMN sapPortIdEgrQosSchedCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.18.1.5 | TmnxCustId | read-only | The value of sapPortIdEgrQosSchedCustId indicates the Customer ID for the associated service. |
| C64 sapPortIdEgrQosSchedFwdOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.18.1.4 | Counter64 | read-only | The value of sapPortIdEgrQosSchedFwdOctets indicates the number of forwarded octets,as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip. |
| C64 sapPortIdEgrQosSchedFwdPkts | 1.3.6.1.4.1.6527.3.1.2.4.3.18.1.3 | Counter64 | read-only | The value of sapPortIdEgrQosSchedFwdPkts indicates the number of forwarded packets, as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip. |
| TNA sapPortIdEgrQosSchedName | 1.3.6.1.4.1.6527.3.1.2.4.3.18.1.1 | TNamedItem | not-accessible | The value of sapPortIdEgrQosSchedName is used as an index of the egress QoS scheduler of this SAP. |
| sapPortIdEgrQosSchedStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.18.1 | not-accessible | Each entry represents the egress statistics about a specific SAP's QoS queue. Entries are created when a scheduler policy is applied to a SAP. | |
| sapPortIdEgrQosSchedStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.18 | not-accessible | The sapPortIdEgrQosSchedStatsTable contains egress QoS queue SAP statistics. This table is used when the SAP is a CCAG or LAG in 'link' mode, or an APS. | |
| TMN sapPortIdIngPortId | 1.3.6.1.4.1.6527.3.1.2.4.3.17.1.2 | TmnxPortID | not-accessible | The value of sapPortIdIngPortId is used as an index of the ingress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in 'link' mode, this object is the TmnxPortID of the member-port on which the scheduler is applied. |
| TMN sapPortIdIngQosSchedCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.17.1.5 | TmnxCustId | read-only | The value of sapPortIdIngQosSchedCustId indicates the Customer ID for the associated service. |
| C64 sapPortIdIngQosSchedFwdOctets | 1.3.6.1.4.1.6527.3.1.2.4.3.17.1.4 | Counter64 | read-only | The value of sapPortIdIngQosSchedFwdOctets indicates the number of forwarded octets,as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip. |
| C64 sapPortIdIngQosSchedFwdPkts | 1.3.6.1.4.1.6527.3.1.2.4.3.17.1.3 | Counter64 | read-only | The value of sapPortIdIngQosSchedFwdPkts indicates the number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip. |
| TNA sapPortIdIngQosSchedName | 1.3.6.1.4.1.6527.3.1.2.4.3.17.1.1 | TNamedItem | not-accessible | The value of sapPortIdIngQosSchedName is used as an index of the ingress QoS scheduler of this SAP. |
| sapPortIdIngQosSchedStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.17.1 | not-accessible | Each entry represents the ingress statistics about a specific SAP's QoS queue. Entries are created when a scheduler policy is applied to a SAP. | |
| sapPortIdIngQosSchedStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.17 | not-accessible | The sapPortIdIngQosSchedStatsTable contains ingress QoS queue SAP statistics. This table is used when the SAP is a CCAG or LAG in 'link' mode, or an APS. | |
| NTF sapPortStateChangeProcessed | 1.3.6.1.4.1.6527.3.1.3.4.3.0.21 | The sapPortStateChangeProcessed notification indicates that the agent has finished processing an access port state change event, and that the operating status of all the affected SAP's has been updated accordingly. The value of the sapNotifyPortId object indicates the ID of the port that experienced the state change. | ||
| NTF sapReceivedProtSrcMac | 1.3.6.1.4.1.6527.3.1.3.4.3.0.15 | The sapReceivedProtSrcMac notification is generated when a protected source MAC is received on a TLS SAP with sapTlsRestProtSrcMac 'true' and sapTlsRestProtSrcMacAction 'alarm-only', or if the TLS SAP belongs to an SHG with tlsShgRestProtSrcMac 'true' and tlsShgRestProtSrcMacAction 'alarm-only'. | ||
| NTF sapReceiveOwnBpdu | 1.3.6.1.4.1.6527.3.1.3.4.5.0.13 | The sapReceiveOwnBpdu notification is generated when the SAP STP received it's own BPDU. | ||
| ROW sapRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.3 | RowStatus | read-create | This object indicates the status of this row. The only values supported during a set operation are 'createAndGo' and 'destroy'. |
| SER sapSplitHorizonGrp | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.24 | ServObjName | read-create | This object specifies the name of the split-horizon group where the SAP belongs to. This object can be set only at the time the row is created. Per default a SAP does not belong to any split-horizon group. The name specified must correspond to an existing split- horizon group in the TLS service where this SAP is defined. |
| STR sapStaticHostAncpString | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.15 | DisplayString | read-create | The value of sapStaticHostAncpString specifies the ancp-string associated to this SAP host. |
| SER sapStaticHostAppProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.17 | ServObjName | read-create | The value of sapStaticHostAppProfile specifies the application profile for this static host. The specified application profile needs to exist in the TIMETRA-BSX-MIB::tmnxBsxAppProfTable. |
| MAC sapStaticHostDynMacAddress | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.11 | MacAddress | read-only | The value of the object sapStaticHostDynMacAddress gives the MAC address learned via ARP in case this is an IP-only static host (sapStaticHostMacAddress is set to 0:0:0:0:0:0). The value 0:0:0:0:0:0 indicates that no MAC address is learned yet. |
| NTF sapStaticHostDynMacConflict | 1.3.6.1.4.1.6527.3.1.3.4.3.0.16 | The sapStaticHostDynMacConflict notification indicates that the system is trying to learn a conflicting IP-only static host dynamic MAC address (sapStaticHostDynMacAddress). | ||
| sapStaticHostEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1 | not-accessible | Each row entry represents information on a statically configured host. Entries can be created and deleted via SNMP SET operations. | |
| TMN sapStaticHostFwdingState | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.14 | TmnxOperState | read-only | The value of sapStaticHostFwdingState indicates the forwarding state of this static host. When the value is 'outOfService', host traffic is not forwarded. When it is 'inService', host traffic is forwarded. |
| STR sapStaticHostIntermediateDestId | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.18 | DisplayString | read-create | The value of sapStaticHostIntermediateDestId specifies to which intermediate destination (for example a DSLAM) this host belongs. |
| IP sapStaticHostIpAddress | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.2 | IpAddress | not-accessible | The value of the object sapStaticHostIpAddress specifies the IP address associated with this static host. The value 0.0.0.0 indicates that no host IP address is specified. |
| MAC sapStaticHostMacAddress | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.3 | MacAddress | not-accessible | The value of the object sapStaticHostMacAddress specifies the MAC address associated with this static host. The value 0:0:0:0:0:0 indicates that no host MAC address is specified. |
| NUM sapStaticHostRetailerIf | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.13 | InterfaceIndexOrZero | read-only | The value of the object sapStaticHostRetailerIf indicates the interface index of the retailer VPRN interface to which this static host belongs. When this object is non zero, the static host belongs to a retailer VPRN. |
| TMN sapStaticHostRetailerSvcId | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.12 | TmnxServId | read-only | The value of the object sapStaticHostRetailerSvcId indicates the service ID of the retailer VPRN service to which this static host belongs. When this object is non zero, the static host belongs to a retailer VPRN. |
| ROW sapStaticHostRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.1 | RowStatus | read-create | The value of the object sapStaticHostRowStatus controls the creation and deletion of rows in this table. |
| U32 sapStaticHostShcvChecks | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.8 | Unsigned32 | read-only | The value of the object sapStaticHostShcvChecks specifies the number of connectivity checks for this static host. |
| INT sapStaticHostShcvOperState | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.7 | INTEGER | read-only | The value of the object sapStaticHostShcvOperState gives the state of the subscriber host connectivity check for this static host. |
| U32 sapStaticHostShcvReplies | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.9 | Unsigned32 | read-only | The value of the object sapStaticHostShcvReplies specifies the number of host replies for this static host. |
| TIM sapStaticHostShcvReplyTime | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.10 | TimeStamp | read-only | The value of the object sapStaticHostShcvReplyTime gives the timestamp of the last successful connectivity check for this static host. |
| SER sapStaticHostSlaProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.6 | ServObjName | read-create | The value of the object sapStaticHostSlaProfile specifies the SLA profile for this static host. The specified SLA profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSLAProfileTable. |
| T/F sapStaticHostSubIdIsSapId | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.16 | TruthValue | read-create | The value of the object sapStaticHostSubIdIsSapId specifies whether the SAP-id is taken as subscriber identification for this static host. |
| SER sapStaticHostSubProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.5 | ServObjName | read-create | The value of the object sapStaticHostSubProfile specifies the subscriber profile for this static host. The specified subscriber profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubProfileTable. |
| STR sapStaticHostSubscrIdent | 1.3.6.1.4.1.6527.3.1.2.4.3.13.1.4 | DisplayString | read-create | The value of the object sapStaticHostSubscrIdent specifies the subscriber identification for this static host. |
| sapStaticHostTable | 1.3.6.1.4.1.6527.3.1.2.4.3.13 | not-accessible | The sapStaticHostTable is used to configure static hosts on a SAP. | |
| NTF sapStatusChanged | 1.3.6.1.4.1.6527.3.1.3.4.3.0.3 | The sapStatusChanged notification is generated when there is a change in the administrative or operating status of an SAP. Notice that this trap is not generated whenever the SAP operating status change is caused by an operating status change on the associated access port. | ||
| TMN sapSubMgmtAdminStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.1 | TmnxEnabledDisabled | read-create | The value of sapSubMgmtAdminStatus specifies whether enhanced subscriber management is enabled on this SAP. |
| SER sapSubMgmtDefAppProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.13 | ServObjName | read-create | The value of sapSubMgmtDefAppProfile specifies the default application profile applicable on this SAP. The corresponding profile is defined in TIMETRA-BSX-MIB::tmnxBsxAppProfTable. |
| SER sapSubMgmtDefSlaProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.3 | ServObjName | read-create | The value of sapSubMgmtDefSlaProfile specifies the default SLA profile applicable on this SAP. The corresponding profile is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSLAProfileTable. |
| INT sapSubMgmtDefSubIdent | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.11 | INTEGER | read-create | The value of sapSubMgmtDefSubIdent specifies what is used as the default subscriber identification applicable on this SAP. This value is used in case no other source (like Radius) provides a subscriber identification string. If the value of this objects is set to 'useSapId', the SAP-id is used as the default subscriber identification string. In this case, sapSubMgmtDefSubIdentString must contain the empty string. If the value of this object is set to 'useString', the value of sapSubMgmtDefSubIdentString is used as the default subscriber identification string. In this case, an empty sapSubMgmtDefSubIdentString means that there is no default subscriber identification configured. |
| STR sapSubMgmtDefSubIdentString | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.12 | DisplayString | read-create | The value of sapSubMgmtDefSubIdentString specifies the default subscriber identification string applicable on this SAP. |
| SER sapSubMgmtDefSubProfile | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.2 | ServObjName | read-create | The value of sapSubMgmtDefSubProfile specifies the default subscriber profile applicable on this SAP. The corresponding profile is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubProfileTable. A value of 'default' is not allowed for this object. |
| sapSubMgmtInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1 | not-accessible | Subscriber management specific information about a SAP. | |
| sapSubMgmtInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.23 | not-accessible | A table that contains SAP subscriber management information. | |
| T/F sapSubMgmtMacDaHashing | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.10 | TruthValue | read-create | The value of sapSubMgmtMacDaHashing specifies whether subscriber traffic egressing a LAG SAP has its egress LAG link selected by a function of the MAC destination address instead of subscriber id. The value of this object is only meaningful if sapSubMgmtAdminStatus is set to 'enabled' and can only be configured for TLS services. |
| SER sapSubMgmtNonSubTrafficAppProf | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.14 | ServObjName | read-create | The value of sapSubMgmtNonSubTrafficAppProf specifies the application profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1. |
| SER sapSubMgmtNonSubTrafficSlaProf | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.9 | ServObjName | read-create | The value of sapSubMgmtNonSubTrafficSlaProf specifies the SLA profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1. |
| STR sapSubMgmtNonSubTrafficSubIdent | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.7 | DisplayString | read-create | The value of sapSubMgmtNonSubTrafficSubIdent specifies the subscriber identification applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1. |
| SER sapSubMgmtNonSubTrafficSubProf | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.8 | ServObjName | read-create | The value of sapSubMgmtNonSubTrafficSubProf specifies the subscriber profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1. |
| T/F sapSubMgmtProfiledTrafficOnly | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.6 | TruthValue | read-create | The value of sapSubMgmtProfiledTrafficOnly specifies whether only profiled traffic is applicable for this SAP. If set to 'true', all SAP queues will be deleted. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1. |
| SER sapSubMgmtSubIdentPolicy | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.4 | ServObjName | read-create | The value of sapSubMgmtSubIdentPolicy specifies the subscriber identification policy applicable on this SAP. The corresponding policy is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubIdentPolicyTable. |
| U32 sapSubMgmtSubscriberLimit | 1.3.6.1.4.1.6527.3.1.2.4.3.23.1.5 | Unsigned32 | read-create | The value of sapSubMgmtSubscriberLimit specifies the maximum number of subscribers allowed for this SAP. If the value is 0, there is no limit. Only if the value is 1, the 'single-sub-parameters' defined with objects sapSubMgmtProfiledTrafficOnly, sapSubMgmtNonSubTrafficSubProf and sapSubMgmtNonSubTrafficSlaProf are meaningful. |
| INT sapSubType | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.39 | INTEGER | read-create | The value of the object sapSubType indicates the sub-type for this SAP. A value of 'regular' indicates a standard SAP. A value of 'capture' specifies a capturing SAP in which triggering packets will be sent to the CPM. Non-triggering packets captured by the 'capture' SAP will be dropped. A value of 'managed' indicates a managed SAP which was created dynamically after receiving triggering packets on a SAP with a sapSubType value of 'capture'. Entries with a value of 'managed' are not user editable and are not maintained in the configuration file. Whereas any of the three values may be returned in in response to an SNMP GET request, only two values may be specified in an SNMP SET request: 'regular' and 'capture'. An attempt to specify a value of 'managed' in an SNMP SET request will fail with an error of 'wrongValue'. The value of this object cannot be changed after creation. |
| INT sapTlsArpReplyAgent | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.39 | INTEGER | read-write | The value of the object sapTlsArpReplyAgent specifies the status of the special ARP response mechanism in the system for ARP requests destined to static or dynamic hosts associated with this SAP. disabled: the ARP reply function is not operational enabled: the ARP reply function is enabled without subscriber identification. enabledWithSubscrIdent: the ARP reply function is enabled with subscriber identification. |
| TPO sapTlsAuthenticationPolicy | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.41 | TPolicyStatementNameOrEmpty | read-write | The value of the object sapTlsAuthenticationPolicy specifies which subscriber authentication policy must be applied when a DHCP msg is received on the interface. The authentication policies must be defined in tmnxSubAuthPlcyTable. The policy will only be applied when sapTlsDhcpSnoop is enabled. |
| INT sapTlsBpduTranslation | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.43 | INTEGER | read-write | The value of the object sapTlsBpduTranslation specifies whether received L2 Protocol Tunnel pdu's are translated before being sent out on this port or sap |
| INT sapTlsBpduTransOper | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.63 | INTEGER | read-only | The value of the object sapTlsBpduTransOper indicates the operational bpdu encapsulation used for BPDU translated frames. |
| TMN sapTlsCustId | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.18 | TmnxCustId | read-only | The Customer ID of the associated service. |
| TPO sapTlsDefMsapPolicy | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.64 | TPolicyStatementNameOrEmpty | read-write | The value of sapTlsDefMsapPolicy specifies the default Managed SAP policy to use to create Managed SAPs when the response from the Radius server does not specify a Managed SAP policy. The value of sapTlsDefMsapPolicy is only valid for a SAP with a sapSubType value of 'capture'. If the value is set to a non-empty string for a SAP with a sapSubType value other than 'capture', an 'inconsistentValue' error will be returned. The Managed SAP policy must be defined in msapPlcyTable, otherwise an 'inconsistentValue' error will be returned. |
| TMN sapTlsDhcpAdminState | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.1 | TmnxEnabledDisabled | read-write | The value of the object sapTlsDhcpAdminState specifies the overall enable/disable state of all DHCP related actions on this Sap. The value 'disabled' allows the user to configure individual DHCP commands but administratively disable them. |
| INT sapTlsDhcpCircuitId | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.7 | INTEGER | read-write | The value of the object sapTlsDhcpCircuitId specifies whether or not the circuit-id suboption is present, and if it is present what information goes in it: - 'none' the circuit-id suboption will not be part of the information option (Option 82). - 'asciiTuple' the ASCII-encoded concatenated tuple consisting of the - access-node-identifier - service-id - interface-name is used. - 'vlanAsciiTuple' the format will include VLAN-id and dot1p bits in addition to what is included in ascii-tuple already. The format is supported on dot1q and qinq encapsulated ports only. Thus, when the option 82 bits are stripped, dot1p bits will be copied to the Ethernet header of an outgoing packet. |
| SER sapTlsDhcpDescription | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.2 | ServObjDesc | read-write | The value of the object sapTlsDhcpDescription specifies a user provided description for DHCP on this Sap. It consists of any printable, seven-bit ASCII characters up to 80 characters in length. |
| INT sapTlsDhcpInfoAction | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.6 | INTEGER | read-write | The value of the object sapTlsDhcpInfoAction specifies the DHCP option reforwarding policy: 'replace' - replace existing information with configured information 'drop' - discard messages with existing relay information if the option-82 information is also present. 'keep' - retain the existing relay information. |
| sapTlsDhcpInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1 | not-accessible | DHCP specific information for a TLS SAP. | |
| sapTlsDhcpInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.14 | not-accessible | sapTlsDhcpInfoTable contains DHCP information related to a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system. | |
| U32 sapTlsDhcpLeasePopulate | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.4 | Unsigned32 | read-write | The value of the object sapTlsDhcpLeasePopulate specifies the maximum number of DHCP lease states allowed on this SAP. |
| sapTlsDhcpLeaseStateEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.16.1 | not-accessible | DHCP Lease State information on a TLS SAP. | |
| NTF sapTlsDHCPLeaseStateOverride | 1.3.6.1.4.1.6527.3.1.3.4.3.0.7 | The sapTlsDHCPLeaseStateOverride notification is generated when an existing DHCP lease state is overridden by a new lease state which has the same IP address but a different MAC address. | ||
| sapTlsDhcpLeaseStateTable | 1.3.6.1.4.1.6527.3.1.2.4.3.16 | not-accessible | sapTlsDhcpLeaseStateTable contains DHCP lease state info for a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system. The content of this table is moved to the svcDhcpLeaseStateTable. | |
| MAC sapTlsDhcpLseStateChAddr | 1.3.6.1.4.1.6527.3.1.2.4.3.16.1.2 | MacAddress | not-accessible | The value of the object sapTlsDhcpLseStateChAddr indicates the MAC address of the DHCP lease state. |
| IP sapTlsDhcpLseStateCiAddr | 1.3.6.1.4.1.6527.3.1.2.4.3.16.1.1 | IpAddress | not-accessible | The value of the object sapTlsDhcpLseStateCiAddr indicates the IP address of the DHCP lease state. |
| OCT sapTlsDhcpLseStateOption82 | 1.3.6.1.4.1.6527.3.1.2.4.3.16.1.4 | OCTET STRING | read-only | The value of the object sapTlsDhcpLseStateOption82 indicates the content of the Option82 for this DHCP lease state. This object was made obsolete in the 4.0 release. |
| U32 sapTlsDhcpLseStatePersistKey | 1.3.6.1.4.1.6527.3.1.2.4.3.16.1.5 | Unsigned32 | read-only | The value of the object sapTlsDhcpLseStatePersistKey indicates a key value that can be used to track this lease state in the persistence file. This object was made obsolete in the 4.0 release. |
| U32 sapTlsDhcpLseStateRemainLseTime | 1.3.6.1.4.1.6527.3.1.2.4.3.16.1.3 | Unsigned32 | read-only | The value of the object sapTlsDhcpLseStateRemainLseTime indicates the remaining lease time of the Ip address of the DHCP lease state. This object was made obsolete in the 4.0 release. |
| NTF sapTlsDHCPLseStEntriesExceeded | 1.3.6.1.4.1.6527.3.1.3.4.3.0.6 | The sapTlsDHCPLseStEntriesExceeded notification is generated when the number of DHCP lease states entries on a given SAP reaches a user configurable upper limit given by sapTlsDhcpLeasePopulate. | ||
| T/F sapTlsDhcpMsapTrigger | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.68 | TruthValue | read-write | The value of sapTlsDhcpMsapTrigger specifies whether the receipt of DHCP trigger packets on this VPLS SAP with a sapSubType value of 'capture' will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of 'managed'. An attempt to set the value sapTlsDhcpMsapTrigger to 'true' on a SAP with sapSubType other than 'capture' will return an 'inconsistentValue' error. |
| U32 sapTlsDhcpOperLeasePopulate | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.5 | Unsigned32 | read-only | The value of the object sapTlsDhcpOperLeasePopulate indicates the number of DHCP lease states currently allocated on this SAP. |
| TMN sapTlsDhcpProxyAdminState | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.10 | TmnxEnabledDisabled | read-write | The value of sapTlsDhcpProxyAdminState specifies the desired administrative state of the proxy server on this interface. Note that in order for the proxy server to be enabled, the value of sapTlsDhcpAdminState must also be 'enabled'. |
| U32 sapTlsDhcpProxyLeaseTime | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.12 | Unsigned32 | read-write | The value of sapTlsDhcpProxyLeaseTime specifies in seconds how long a DHCP client is allowed to use the offered IP address. Value 0 means the lease time provided by a RADIUS or an upstream DHCP server will not be overridden. A lease time of 7 days is used when RADIUS does not provide a lease time. |
| T/F sapTlsDhcpProxyLTRadiusOverride | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.13 | TruthValue | read-write | The value of sapTlsDhcpProxyLTRadiusOverride specifies whether or not the lease time provided by the RADIUS server is presented to the DHCP client. By default the proxy-server will always make use of sapTlsDhcpProxyLeaseTime, regardless of what lease time information is provided from the RADIUS server. When sapTlsDhcpProxyLTRadiusOverride is set to 'true', the proxy-server will use the lease time information provided by the RADIUS server, regardless of the configured one. |
| IP sapTlsDhcpProxyServerAddr | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.11 | IpAddress | read-write | The value of sapTlsDhcpProxyServerAddr specifies the IP address which will be used as the source address of the emulated DHCP server in the context of this VPLS SAP. This address is mandatory for the proxy server capability and it should be in the context of the subnet represented by this VPLS. |
| INT sapTlsDhcpRemoteId | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.8 | INTEGER | read-write | The value of the object sapTlsDhcpRemoteId specifies what information goes into the remote-id suboption in the DHCP Relay packet. If the value of this object is set to 'none', the remote-id suboption will not be part of the information option (Option 82). If the value of this object is set to 'mac', the MAC address of the remote end is encoded in the suboption. If the value of this object is set to 'remote-id', sapTlsDhcpRemoteIdString will represent the remote-id. By default, the remote-id value is none. |
| STR sapTlsDhcpRemoteIdString | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.9 | DisplayString | read-write | The value of the object sapTlsDhcpRemoteIdString specifies the remote-id. This object exists only if sapTlsDhcpRemoteId has a value of 'remote-id'. |
| TMN sapTlsDhcpSnoop | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.3 | TmnxEnabledDisabled | read-write | The value of the object sapTlsDhcpSnoop specifies the enable/disable state for DHCP snooping on this Sap. Note that in order for snooping to be enabled the object sapTlsDhcpAdminState must also have the value enabled. |
| TMN sapTlsDhcpSnooping | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.32 | TmnxEnabledDisabled | read-write | The value of the object sapTlsDhcpSnooping specifies whether or not DHCP packets received on this SAP will be snooped. This object was made obsolete in the 3.0 release. |
| C32 sapTlsDhcpStatsClntDropdPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.5 | Counter32 | read-only | The value of the object sapTlsDhcpStatsClntDropdPckts indicates the number of DHCP client packets that have been dropped on this SAP. |
| C32 sapTlsDhcpStatsClntForwdPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.3 | Counter32 | read-only | The value of the object sapTlsDhcpStatsClntForwdPckts indicates the number of DHCP client packets that have been forwarded on this SAP. |
| C32 sapTlsDhcpStatsClntProxLSPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.8 | Counter32 | read-only | The value of the object sapTlsDhcpStatsClntProxLSPckts indicates the number of DHCP client packets that have been proxied on this SAP based on a lease state. The lease itself can have been obtained from a DHCP or RADIUS server. This is the so called lease split functionality. |
| C32 sapTlsDhcpStatsClntProxRadPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.7 | Counter32 | read-only | The value of the object sapTlsDhcpStatsClntProxRadPckts indicates the number of DHCP client packets that have been proxied on this SAP based on data received from a RADIUS server. |
| C32 sapTlsDhcpStatsClntSnoopdPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.1 | Counter32 | read-only | The value of the object sapTlsDhcpStatsClntSnoopdPckts indicates the number of DHCP client packets that have been snooped on this SAP. |
| sapTlsDhcpStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1 | not-accessible | DHCP statistics for a TLS SAP. | |
| C32 sapTlsDhcpStatsGenForceRenPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.10 | Counter32 | read-only | The value of the object sapTlsDhcpStatsGenForceRenPckts indicates the number of DHCP FORCERENEW messages spoofed on this SAP to the DHCP clients. |
| C32 sapTlsDhcpStatsGenReleasePckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.9 | Counter32 | read-only | The value of the object sapTlsDhcpStatsGenReleasePckts indicates the number of DHCP RELEASE messages spoofed on this SAP to the DHCP server. |
| C32 sapTlsDhcpStatsSrvrDropdPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.6 | Counter32 | read-only | The value of the object sapTlsDhcpStatsSrvrDropdPckts indicates the number of DHCP server packets that have been dropped on this SAP. |
| C32 sapTlsDhcpStatsSrvrForwdPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.4 | Counter32 | read-only | The value of the object sapTlsDhcpStatsSrvrForwdPckts indicates the number of DHCP server packets that have been forwarded on this SAP. |
| C32 sapTlsDhcpStatsSrvrSnoopdPckts | 1.3.6.1.4.1.6527.3.1.2.4.3.15.1.2 | Counter32 | read-only | The value of the object sapTlsDhcpStatsSrvrSnoopdPckts indicates the number of DHCP server packets that have been snooped on this SAP. |
| sapTlsDhcpStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.15 | not-accessible | sapTlsDhcpStatsTable contains DHCP statistics related to a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system. | |
| NTF sapTlsDHCPSuspiciousPcktRcvd | 1.3.6.1.4.1.6527.3.1.3.4.3.0.8 | The sapTlsDHCPSuspiciousPcktRcvd notification is generated when a DHCP packet is received with suspicious content. | ||
| BIT sapTlsDhcpVendorIncludeOptions | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.14 | Bits | read-write | The value of sapTlsDhcpVendorIncludeOptions specifies what is encoded in the Alcatel vendor specific sub-option of option 82. The value of this object is only used when sapTlsDhcpInfoAction is 'replace'. |
| STR sapTlsDhcpVendorOptionString | 1.3.6.1.4.1.6527.3.1.2.4.3.14.1.15 | DisplayString | read-write | The value of sapTlsDhcpVendorOptionString specifies the string that goes into the Alcatel vendor specific sub-option of option 82. This string is only used when sapTlsDhcpInfoAction is set to 'replace'. |
| TMN sapTlsDiscardUnknownSource | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.34 | TmnxEnabledDisabled | read-write | with the object sapTlsMacAddressLimit a limit can be configured for the max number of MAC addresses that will be learned on this SAP. When this limit is reached, packets with unknown source MAC address are forwarded by default. By setting sapTlsDiscardUnknownSource to enabled, packets with unknown source MAC will be dropped in stead. |
| TNA sapTlsEgressMcastGroup | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.46 | TNamedItemOrEmpty | read-write | The value of the object sapTlsEgressMcastGroup specifies the Egress Multicast Group this SAP belongs to. |
| sapTlsInfoEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1 | not-accessible | TLS specific information about a SAP. | |
| sapTlsInfoTable | 1.3.6.1.4.1.6527.3.1.2.4.3.3 | not-accessible | A table that contains TLS SAP information. | |
| T/F sapTlsL2ptForceBoundary | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.61 | TruthValue | read-write | The value of sapTlsL2ptForceBoundary specifies if sapTlsL2ptTermination is enforced for its managed SAP's. Setting the value of the object sapTlsL2ptForceBoundary of a SAP in a Management VPLS to `true' forces all its managed SAP's to have sapTlsL2ptTermination enabled. This value can only be `true' if the SAP belongs to a management VPLS. If this SAP has managed SAP's already with sapTlsL2ptTermination disabled, it is not allowed to set sapTlsL2ptForceBoundary to `true'. |
| L2P sapTlsL2ptForceProtocols | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.66 | L2ptProtocols | read-write | The value of the object sapTlsL2ptForceProtocols specifies which L2 Protocol Tunnel pdu's must be terminated by SAP's managed by this SAP. This object is only relevant if the value of the object sapTlsL2ptForceBoundary is 'true'. For every SAP managed by this SAP, each L2 protocol specified by sapTlsL2ptForceProtocols must be terminated, while other L2 protocols may or may not be terminated, depending on the value of sapTlsL2ptProtocols of that managed SAP. |
| L2P sapTlsL2ptProtocols | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.65 | L2ptProtocols | read-write | The value of the object sapTlsL2ptTermination specifies which L2 Protocol Tunnel pdu's are terminated on this port or sap |
| C32 sapTlsL2ptStatsCdpBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.42 | Counter32 | read-only | The value of sapTlsL2ptStatsCdpBpdusRx indicates the number of CDP bpdus received on this SAP. |
| C32 sapTlsL2ptStatsCdpBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.43 | Counter32 | read-only | The value of sapTlsL2ptStatsCdpBpdusTx indicates the number of CDP bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsDtpBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.46 | Counter32 | read-only | The value of sapTlsL2ptStatsDtpBpdusRx indicates the number of DTP bpdus received on this SAP. |
| C32 sapTlsL2ptStatsDtpBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.47 | Counter32 | read-only | The value of sapTlsL2ptStatsDtpBpdusTx indicates the number of DTP bpdus transmitted on this SAP. |
| sapTlsL2ptStatsEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1 | not-accessible | Layer 2 Protocol Tunneling Statistics for a specific SAP. The statistics are provided for each combination of Destination Address and LLC SNAP type. | |
| C32 sapTlsL2ptStatsL2ptEncapCdpBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.32 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapCdpBpdusRx indicates the number of L2PT encapsulated CDP bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapCdpBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.33 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapCdpBpdusTx indicates the number of L2PT encapsulated CDP bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapDtpBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.36 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapDtpBpdusRx indicates the number of L2PT encapsulated DTP bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapDtpBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.37 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapDtpBpdusTx indicates the number of L2PT encapsulated DTP bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapPagpBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.38 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapPagpBpdusRx indicates the number of L2PT encapsulated PAGP bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapPagpBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.39 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapPagpBpdusTx indicates the number of L2PT encapsulated PAGP bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapPvstConfigBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.8 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapPvstConfigBpdusRx indicates the number of L2PT encapsulated PVST config bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapPvstConfigBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.9 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapPvstConfigBpdusTx indicates the number of L2PT encapsulated PVST config bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapPvstRstBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.10 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapPvstRstBpdusRx indicates the number of L2PT encapsulated PVST rst bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapPvstRstBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.11 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapPvstRstBpdusTx indicates the number of L2PT encapsulated PVST rst bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapPvstTcnBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.12 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapPvstTcnBpdusRx indicates the number of L2PT encapsulated PVST tcn bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapPvstTcnBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.13 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapPvstTcnBpdusTx indicates the number of L2PT encapsulated PVST tcn bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapStpConfigBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.2 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapStpConfigBpdusRx indicates the number of L2PT encapsulated STP config bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapStpConfigBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.3 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapStpConfigBpdusTx indicates the number of L2PT encapsulated STP config bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapStpRstBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.4 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapStpRstBpdusRx indicates the number of L2PT encapsulated STP rst bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapStpRstBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.5 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapStpRstBpdusTx indicates the number of L2PT encapsulated STP rst bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapStpTcnBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.6 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapStpTcnBpdusRx indicates the number of L2PT encapsulated STP tcn bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapStpTcnBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.7 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapStpTcnBpdusTx indicates the number of L2PT encapsulated STP tcn bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapUdldBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.40 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapUdldBpdusRx indicates the number of L2PT encapsulated UDLD bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapUdldBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.41 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapUdldBpdusTx indicates the number of L2PT encapsulated UDLD bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapVtpBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.34 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapVtpBpdusRx indicates the number of L2PT encapsulated VTP bpdus received on this SAP. |
| C32 sapTlsL2ptStatsL2ptEncapVtpBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.35 | Counter32 | read-only | The value of sapTlsL2ptStatsL2ptEncapVtpBpdusTx indicates the number of L2PT encapsulated VTP bpdus transmitted on this SAP. |
| TIM sapTlsL2ptStatsLastClearedTime | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.1 | TimeStamp | read-only | The value of sapTlsL2ptStatsLastClearedTime indicates the last time that these stats were cleared. The value zero indicates that they have not been cleared yet. |
| C32 sapTlsL2ptStatsOtherBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.26 | Counter32 | read-only | The value of sapTlsL2ptStatsOtherBpdusRx indicates the number of other bpdus received on this SAP. |
| C32 sapTlsL2ptStatsOtherBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.27 | Counter32 | read-only | The value of sapTlsL2ptStatsOtherBpdusTx indicates the number of other bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsOtherInvalidBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.30 | Counter32 | read-only | The value of sapTlsL2ptStatsOtherInvalidBpdusRx indicates the number of other invalid bpdus received on this SAP. |
| C32 sapTlsL2ptStatsOtherInvalidBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.31 | Counter32 | read-only | The value of sapTlsL2ptStatsOtherInvalidBpdusTx indicates the number of other invalid bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsOtherL2ptBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.28 | Counter32 | read-only | The value of sapTlsL2ptStatsOtherL2ptBpdusRx indicates the number of other L2PT bpdus received on this SAP. |
| C32 sapTlsL2ptStatsOtherL2ptBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.29 | Counter32 | read-only | The value of sapTlsL2ptStatsOtherL2ptBpdusTx indicates the number of other L2PT bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsPagpBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.48 | Counter32 | read-only | The value of sapTlsL2ptStatsPagpBpdusRx indicates the number of PAGP bpdus received on this SAP. |
| C32 sapTlsL2ptStatsPagpBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.49 | Counter32 | read-only | The value of sapTlsL2ptStatsPagpBpdusTx indicates the number of PAGP bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsPvstConfigBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.20 | Counter32 | read-only | The value of sapTlsL2ptStatsPvstConfigBpdusRx indicates the number of PVST config bpdus received on this SAP. |
| C32 sapTlsL2ptStatsPvstConfigBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.21 | Counter32 | read-only | The value of sapTlsL2ptStatsPvstConfigBpdusTx indicates the number of PVST config bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsPvstRstBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.22 | Counter32 | read-only | The value of sapTlsL2ptStatsPvstRstBpdusRx indicates the number of PVST rst bpdus received on this SAP. |
| C32 sapTlsL2ptStatsPvstRstBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.23 | Counter32 | read-only | The value of sapTlsL2ptStatsPvstRstBpdusTx indicates the number of PVST rst bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsPvstTcnBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.24 | Counter32 | read-only | The value of sapTlsL2ptStatsPvstTcnBpdusRx indicates the number of PVST tcn bpdus received on this SAP. |
| C32 sapTlsL2ptStatsPvstTcnBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.25 | Counter32 | read-only | The value of sapTlsL2ptStatsPvstTcnBpdusTx indicates the number of PVST tcn bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsStpConfigBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.14 | Counter32 | read-only | The value of sapTlsL2ptStatsStpConfigBpdusRx indicates the number of STP config bpdus received on this SAP. |
| C32 sapTlsL2ptStatsStpConfigBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.15 | Counter32 | read-only | The value of sapTlsL2ptStatsStpConfigBpdusTx indicates the number of STP config bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsStpRstBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.16 | Counter32 | read-only | The value of sapTlsL2ptStatsStpRstBpdusRx indicates the number of STP rst bpdus received on this SAP. |
| C32 sapTlsL2ptStatsStpRstBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.17 | Counter32 | read-only | The value of sapTlsL2ptStatsStpRstBpdusTx indicates the number of STP rst bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsStpTcnBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.18 | Counter32 | read-only | The value of sapTlsL2ptStatsStpTcnBpdusRx indicates the number of STP tcn bpdus received on this SAP. |
| C32 sapTlsL2ptStatsStpTcnBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.19 | Counter32 | read-only | The value of sapTlsL2ptStatsStpTcnBpdusTx indicates the number of STP tcn bpdus transmitted on this SAP. |
| sapTlsL2ptStatsTable | 1.3.6.1.4.1.6527.3.1.2.4.3.42 | not-accessible | A table that contains SAP Layer 2 Protocol Tunneling Statistics. This table complements sapTlsInfoTable. Rows in this table are created and deleted automatically by the system. | |
| C32 sapTlsL2ptStatsUdldBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.50 | Counter32 | read-only | The value of sapTlsL2ptStatsUdldBpdusRx indicates the number of UDLD bpdus received on this SAP. |
| C32 sapTlsL2ptStatsUdldBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.51 | Counter32 | read-only | The value of sapTlsL2ptStatsUdldBpdusTx indicates the number of UDLD bpdus transmitted on this SAP. |
| C32 sapTlsL2ptStatsVtpBpdusRx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.44 | Counter32 | read-only | The value of sapTlsL2ptStatsVtpBpdusRx indicates the number of VTP bpdus received on this SAP. |
| C32 sapTlsL2ptStatsVtpBpdusTx | 1.3.6.1.4.1.6527.3.1.2.4.3.42.1.45 | Counter32 | read-only | The value of sapTlsL2ptStatsVtpBpdusTx indicates the number of VTP bpdus transmitted on this SAP. |
| TMN sapTlsL2ptTermination | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.42 | TmnxEnabledDisabled | read-write | The value of the object sapTlsL2ptTermination specifies whether received L2 Protocol Tunnel pdu's are terminated on this port or sap |
| TLS sapTlsLimitMacMove | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.31 | TlsLimitMacMove | read-write | When sapTlsLimitMacMove value is set to 'blockable' the agent will monitor the MAC relearn rate on this SAP, and it will block it when the re-learn rate specified by svcTlsMacMoveMaxRate is exceeded. When the value is 'nonBlockable' this SAP will not be blocked, and another blockable SAP will be blocked instead. |
| TLS sapTlsLimitMacMoveLevel | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.62 | TlsLimitMacMoveLevel | read-write | The value of the object sapTlsLimitMacMoveLevel specifies the hierarchy in which SAPs are blocked when a MAC-move limit is exceeded. When a MAC is moving among multiple SAPs or spoke-SDPs, the SAP bind or spoke-SDP bind with the lower level is blocked first. (tertiary is the lowest) |
| I32 sapTlsMacAddressLimit | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.19 | Integer32 | read-write | The value of the object sapTlsMacAddressLimit specifies the maximum number of learned and static entries allowed in the FDB of this SAP. The value 0 means: no limit for this SAP. When the value of TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is not 'c', the maximum value of sapTlsMacAddressLimit is '131071'. |
| NTF sapTlsMacAddrLimitAlarmCleared | 1.3.6.1.4.1.6527.3.1.3.4.3.0.5 | The trap sapTlsMacAddrLimitAlarmCleared is sent whenever the number of MAC addresses stored in the FDB for this SAP drops to the watermark specified by the object svcTlsFdbTableFullLowWatermark. | ||
| NTF sapTlsMacAddrLimitAlarmRaised | 1.3.6.1.4.1.6527.3.1.3.4.3.0.4 | The trap sapTlsMacAddrLimitAlarmRaised is sent whenever the number of MAC addresses stored in the FDB for this SAP increases to reach the watermark specified by the object svcTlsFdbTableFullHighWatermark. | ||
| TMN sapTlsMacAgeing | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.23 | TmnxEnabledDisabled | read-write | The value of the object sapTlsMacAgeing specifies whether the MAC aging process is enabled for this SAP. the value is ignored if MAC aging is disabled on service level. |
| TMN sapTlsMacLearning | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.22 | TmnxEnabledDisabled | read-write | The value of the object sapTlsMacLearning specifies whether the MAC learning process is enabled for this SAP. The value is ignored if MAC learning is disabled on service level. |
| NTF sapTlsMacMoveExceeded | 1.3.6.1.4.1.6527.3.1.3.4.3.0.17 | The sapTlsMacMoveExceeded notification is generated when the SAP exceeds the TLS svcTlsMacMoveMaxRate. | ||
| U32 sapTlsMacMoveNextUpTime | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.58 | Unsigned32 | read-only | The value of the object sapTlsMacMoveNextUpTime counts down the time in seconds until a SAP that has been brought down due to exceeding the TLS svcTlsMacMoveMaxRate, sapOperFlags 'relearnLimitExceeded', is automatically brought up again. When this value is 0xffff, the SAP will never be automatically brought up. The value is zero when sapOperStatus is 'up'. |
| U32 sapTlsMacMoveRateExcdLeft | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.59 | Unsigned32 | read-only | The value of the object sapTlsMacMoveRateExcdLeft counts down the number of times this SAP can exceed the TLS svcTlsMacMoveMaxRate and still be automatically brought up. |
| TMN sapTlsMacPinning | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.33 | TmnxEnabledDisabled | read-write | The value of the object sapTlsMacPinning specifies whether or not MAC address pinning is active on this SAP. The value will be set by default to disabled. However for a SAP that belongs to a residential SHG, the value is set to enabled by the system, and cannot be altered by the operator. Setting the value to enable disables re-learning of MAC addresses on other SAPs or spoke-SDPs within the same VPLS; the MAC address will hence remain attached to the SAP for the duration of its age-timer. This object has effect only for MAC addresses learned via the normal MAC learning process, and not for entries learned via DHCP. |
| sapTlsManagedVlanListEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.11.1 | not-accessible | Each row specifies a range of VLANS associated with a SAP of a MVPLS. Ranges may contains overlapping sections only for Mvpls SAPs that belong to the same service. | |
| sapTlsManagedVlanListTable | 1.3.6.1.4.1.6527.3.1.2.4.3.11 | not-accessible | This table is used only for SAPs that are part of a management VPLS. It indicates for each SAP the ranges of associated VLANs that will be affected when the SAP changes state. | |
| T/F sapTlsMmrpDeclared | 1.3.6.1.4.1.6527.3.1.2.4.3.51.1.2 | TruthValue | read-only | The value of sapTlsMmrpDeclared indicates whether the MRP applicant on this SAP is declaring this MAC address on behalf of MMRP. |
| sapTlsMmrpEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.51.1 | not-accessible | MMRP specific information about a MAC address managed by MMRP on a SAP in a TLS. | |
| MAC sapTlsMmrpMacAddr | 1.3.6.1.4.1.6527.3.1.2.4.3.51.1.1 | MacAddress | not-accessible | The value of sapTlsMmrpMacAddr indicates an ethernet MAC address which is being managed by MMRP on this SAP. |
| T/F sapTlsMmrpRegistered | 1.3.6.1.4.1.6527.3.1.2.4.3.51.1.3 | TruthValue | read-only | The value of sapTlsMmrpRegistered indicates whether the MRP registrant on this SAP has notified MMRP of a registration of this MAC address. |
| sapTlsMmrpTable | 1.3.6.1.4.1.6527.3.1.2.4.3.51 | not-accessible | This table contains an entry for each MAC address managed by Multiple MAC Registration Protocol (MMRP) on the SAP for the TLS. Entries are dynamically created and destroyed by the system as the MAC Addresses are registered or declared in MMRP. | |
| C32 sapTlsMrpDroppedPdus | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.2 | Counter32 | read-only | The value of sapTlsMrpDroppedPdus indicates the number of dropped MRP packets on this SAP. |
| sapTlsMrpEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1 | not-accessible | MRP specific information about a SAP in a TLS. | |
| U32 sapTlsMrpJoinTime | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.69 | Unsigned32 | read-write | The value of sapTlsMrpJoinTime specifies a timer value in 10ths of seconds which determines the maximum rate at which attribute join messages can be sent on the SAP. |
| U32 sapTlsMrpLeaveAllTime | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.71 | Unsigned32 | read-write | The value of sapTlsMrpLeaveAllTime specifies the a timer value in 10ths of seconds which determines the frequency where all attribute declarations on the SAP are all refreshed. |
| U32 sapTlsMrpLeaveTime | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.70 | Unsigned32 | read-write | The value of sapTlsMrpLeaveTime specifies a timer value in 10ths of seconds which determines the amount of time a registered attribute is held in leave state before the registration is removed. |
| T/F sapTlsMrpPeriodicEnabled | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.73 | TruthValue | read-write | The value of sapTlsMrpPeriodicEnabled specifies whether re-transmission of attribute declarations is enabled. |
| U32 sapTlsMrpPeriodicTime | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.72 | Unsigned32 | read-write | The value of sapTlsMrpPeriodicTime specifies a timer value in 10ths of seconds which determines the frequency of re-transmission of attribute declarations. |
| C32 sapTlsMrpRxEmptyEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.8 | Counter32 | read-only | The value of sapTlsMrpRxEmptyEvent indicates the number of 'Empty' MRP events received on this SAP. |
| C32 sapTlsMrpRxInEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.6 | Counter32 | read-only | The value of sapTlsMrpRxInEvent indicates the number of 'In' MRP events received on this SAP. |
| C32 sapTlsMrpRxJoinEmptyEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.7 | Counter32 | read-only | The value of sapTlsMrpRxJoinEmptyEvent indicates the number of 'Join Empty' MRP events received on this SAP. |
| C32 sapTlsMrpRxJoinInEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.5 | Counter32 | read-only | The value of sapTlsMrpRxJoinInEvent indicates the number of 'Join-In' MRP events received on this SAP. |
| C32 sapTlsMrpRxLeaveEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.9 | Counter32 | read-only | The value of sapTlsMrpRxLeaveEvent indicates the number of 'Leave' MRP events received on this SAP. |
| C32 sapTlsMrpRxNewEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.4 | Counter32 | read-only | The value of sapTlsMrpRxNewEvent indicates the number of 'New' MRP events received on this SAP. |
| C32 sapTlsMrpRxPdus | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.1 | Counter32 | read-only | The value of sapTlsMrpRxPdus indicates the number of MRP packets received on this SAP. |
| sapTlsMrpTable | 1.3.6.1.4.1.6527.3.1.2.4.3.50 | not-accessible | The sapTlsMrpTable augments sapTlsInfoTable with attributes of the Multiple Registration Protocol (MRP) feature for the TLS SAP. | |
| C32 sapTlsMrpTxEmptyEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.14 | Counter32 | read-only | The value of sapTlsMrpTxEmptyEvent indicates the number of 'Empty' MRP events transmitted on this SAP. |
| C32 sapTlsMrpTxInEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.12 | Counter32 | read-only | The value of sapTlsMrpTxInEvent indicates the number of 'In' MRP events transmitted on this SAP. |
| C32 sapTlsMrpTxJoinEmptyEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.13 | Counter32 | read-only | The value of sapTlsMrpTxJoinEmptyEvent indicates the number of 'Join Empty' MRP events transmitted on this SAP. |
| C32 sapTlsMrpTxJoinInEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.11 | Counter32 | read-only | The value of sapTlsMrpTxJoinInEvent indicates the number of 'Join-In' MRP events transmitted on this SAP. |
| C32 sapTlsMrpTxLeaveEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.15 | Counter32 | read-only | The value of sapTlsMrpTxLeaveEvent indicates the number of 'Leave' MRP events transmitted on this SAP. |
| C32 sapTlsMrpTxNewEvent | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.10 | Counter32 | read-only | The value of sapTlsMrpTxNewEvent indicates the number of 'New' MRP events transmitted on this SAP. |
| C32 sapTlsMrpTxPdus | 1.3.6.1.4.1.6527.3.1.2.4.3.50.1.3 | Counter32 | read-only | The value of sapTlsMrpTxPdus indicates the number of MRP packets transmitted on this SAP. |
| BRI sapTlsMstiDesignatedBridge | 1.3.6.1.4.1.6527.3.1.2.4.3.24.1.6 | BridgeId | read-only | The value of the object sapTlsMstiDesignatedBridge indicates the Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment for this MSTI. |
| I32 sapTlsMstiDesignatedPort | 1.3.6.1.4.1.6527.3.1.2.4.3.24.1.7 | Integer32 | read-only | The value of the object sapTlsMstiDesignatedPort indicates the Port Identifier of the port on the Designated Bridge for this port's segment for this MSTI. |
| sapTlsMstiEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.24.1 | not-accessible | Information about a specific MSTI for a SAP. | |
| TIM sapTlsMstiLastMgmtChange | 1.3.6.1.4.1.6527.3.1.2.4.3.24.1.3 | TimeStamp | read-only | The value of the object sapTlsMstiLastMgmtChange indicates the value of sysUpTime at the time of the most recent management-initiated change to this SAP MSTI information. |
| INT sapTlsMstiPathCost | 1.3.6.1.4.1.6527.3.1.2.4.3.24.1.2 | INTEGER | read-write | The value of the object sapTlsMstiPathCost specifies the contribution of this port to the MSTI path cost of paths towards the spanning tree regional root which include this port. |
| STP sapTlsMstiPortRole | 1.3.6.1.4.1.6527.3.1.2.4.3.24.1.4 | StpPortRole | read-only | sapTlsMstiPortRole indicates the current role of the sap in the MSTI as defined by the Spanning Tree Protocol. |
| TST sapTlsMstiPortState | 1.3.6.1.4.1.6527.3.1.2.4.3.24.1.5 | TStpPortState | read-only | The value of the object sapTlsMstiPortState indicates the port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the 'broken' state. |
| I32 sapTlsMstiPriority | 1.3.6.1.4.1.6527.3.1.2.4.3.24.1.1 | Integer32 | read-write | The value of the object sapTlsMstiPriority specifies the value of the port priority field which is contained in the most significant 4 bits of the 16-bit Port ID associated with this SAP and MSTI. As only the most significant 4 bits of the value are used, the actual value of this object is limited to multiples of 16: e.g. the agent rounds down the value to one of: 0, 16, 32, .. , 224, 240. |
| sapTlsMstiTable | 1.3.6.1.4.1.6527.3.1.2.4.3.24 | not-accessible | This table contains Multiple Spanning Tree Instance information for the SAP. Each management VPLS running MSTP can have upto 15 MSTI. An entry in this table is automatically created when a tlsMstiEntry is created. | |
| U32 sapTlsMvplsMaxVlanTag | 1.3.6.1.4.1.6527.3.1.2.4.3.11.1.2 | Unsigned32 | not-accessible | The value of sapTlsMvplsMaxVlanTag specifies the right bound (i.e. max. value) of a range of VLANs that are associated with the Mvpls SAP. Special values are: 0: this value is reserved for the null tag. 4095: this value denotes the default SAP. |
| TMN sapTlsMvplsMgmtEncapValue | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.38 | TmnxEncapVal | read-only | The value of sapTlsMvplsMgmtEncapValue indicates the SAP Encap value of the SAP in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable. |
| MST sapTlsMvplsMgmtMsti | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.57 | MstiInstanceIdOrZero | read-only | The value of the object sapTlsMvplsMgmtMsti indicates the MST-instance in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. A value of 0 indicates the CIST. This object is only valid if sapTlsMvplsPruneState is different from notApplicable. |
| TMN sapTlsMvplsMgmtPortId | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.37 | TmnxPortID | read-only | The value of sapTlsMvplsMgmtPortId indicates the SAP port Id of the SAP in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable. |
| TMN sapTlsMvplsMgmtService | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.36 | TmnxServId | read-only | The value of sapTlsMvplsMgmtService indicates the service Id of the service where the STP instance is running that is managing this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable. |
| U32 sapTlsMvplsMinVlanTag | 1.3.6.1.4.1.6527.3.1.2.4.3.11.1.1 | Unsigned32 | not-accessible | The value of sapTlsMvplsMinVlanTag specifies the left bound (i.e. min. value) of a range of VLANs that are associated with the Mvpls SAP. sapTlsMvplsMinVlanTag must be smaller than (or equal to) sapTlsMvplsMaxVlanTag. Special values are: 0: this value is reserved for the null tag. 4095: this value denotes the default SAP. |
| MVP sapTlsMvplsPruneState | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.35 | MvplsPruneState | read-only | The value of sapTlsMvplsPruneState indicates the mVPLS prune state of the SAP. The object will be set to notApplicable if the SAP is not managed by a mVPLS. If the SAP is managed the state reflects whether or not the SAP is pruned by the STP instance running in the mVPLS instance. |
| ROW sapTlsMvplsRowStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.11.1.3 | RowStatus | read-create | The value of sapTlsMvplsRowStatus specifies the status of this row. The only values supported during a set operation are 'createAndGo' and 'destroy'. A row (i.e. a range of VLAN tags) can be destroyed only if there are no SAPs defined in regular VPLSses in this range. |
| I32 sapTlsNumMacAddresses | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.20 | Integer32 | read-only | The value of the object sapTlsNumMacAddresses indicates the number of MAC addresses currently present in the FDB that belong to this SAP (Both learned and static MAC addresses are counted). |
| I32 sapTlsNumStaticMacAddresses | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.21 | Integer32 | read-only | The value of the object sapTlsNumStaticMacAddresses indicates the number of static MAC addresses currently present in the FDB that belong to this SAP. |
| T/F sapTlsPppoeMsapTrigger | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.67 | TruthValue | read-write | The value of sapTlsPppoeMsapTrigger specifies whether the receipt of PPPoE trigger packets on a VPLS SAP with a sapSubType value of 'capture' will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of 'managed'. An attempt to set the value sapTlsPppoeMsapTrigger to 'true' on a SAP with sapSubType other than 'capture' will return an 'inconsistentValue' error. |
| T/F sapTlsRestProtSrcMac | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.49 | TruthValue | read-write | The value of the object sapTlsRestProtSrcMac specifies how the agent will handle relearn requests for protected MAC addresses. When the value of this object is 'true' requests to relearn a protected MAC address will be ignored. In addition, if the value of sapTlsRestProtSrcMacAction is 'disable', then the SAP where the protected source MAC was seen will be brought operationally down. |
| INT sapTlsRestProtSrcMacAction | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.60 | INTEGER | read-write | The value of the object sapTlsRestProtSrcMacAction indicates the action to take whenever a relearn request for a protected MAC is received on a restricted SAP. When the value of this object is 'disable' the SAP will be placed in the operational down state, with the operating flag 'recProtSrcMac' set. When the value of this object is 'alarm-only', the SAP will be left up and only a notification, sapReceivedProtSrcMac, will be generated. |
| T/F sapTlsRestUnprotDstMac | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.50 | TruthValue | read-write | The value of the object sapTlsRestUnprotDstMac specifies how the system will forward packets destined to an unprotected MAC address. When the value of this object is 'true' packets destined to an unprotected MAC address will be dropped. |
| INT sapTlsShcvAction | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.53 | INTEGER | read-write | The value of the object sapTlsShcvAction indicates whether any action should be triggered when the connectivity check fails. |
| U32 sapTlsShcvInterval | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.56 | Unsigned32 | read-write | The value of the object sapTlsShcvInterval specifies the interval in minutes between connectivity checks. Zero means no connectivity checking. |
| IP sapTlsShcvSrcIp | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.54 | IpAddress | read-write | The value of the object sapTlsShcvSrcIp specifies the source IP address used when doing the connectivity check. The value 0.0.0.0 indicates that no host IP address is specified. |
| MAC sapTlsShcvSrcMac | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.55 | MacAddress | read-write | The value of the object sapTlsShcvSrcMac specifies the MAC address used when doing the connectivity check. The value 0:0:0:0:0:0 indicates that no host MAC address is specified. |
| INT sapTlsStpAdminPointToPoint | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.25 | INTEGER | read-write | The value of the object sapTlsStpAdminPointToPoint specifies the administrative point-to-point status of the LAN segment attached to this sap. The value 'forceTrue' means that this port should always be treated as if it is connected to a point-to-point link. The value of 'forceFalse' means that this port should be treated as having a shared media connection. |
| TMN sapTlsStpAdminStatus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.1 | TmnxEnabledDisabled | read-write | The value of the object sapTlsStpAdminStatus specifies whether this SAP participates in the TLS's Spanning Tree Protocol. |
| TMN sapTlsStpAutoEdge | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.27 | TmnxEnabledDisabled | read-write | sapTlsStpAutoEdge specifies whether this SAP is enabled for auto-edge detection as defined by Rapid Spanning Tree Protocol. |
| INT sapTlsStpBpduEncap | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.6 | INTEGER | read-write | The value of the object sapTlsStpBpduEncap specifies the type of encapsulation used on BPDUs sent out and received on this SAP. |
| BRI sapTlsStpDesignatedBridge | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.8 | BridgeId | read-only | The value of the object sapTlsStpDesignatedBridge indicates the Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. |
| I32 sapTlsStpDesignatedPort | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.9 | Integer32 | read-only | The value of the object sapTlsStpDesignatedPort indicates the Port Identifier of the port on the Designated Bridge for this port's segment. |
| STP sapTlsStpException | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.40 | StpExceptionCondition | read-only | The value of the object sapTlsStpException indicates whether an STP exception condition is present on this Sap. - none : no exception condition found. - oneWayCommuniation : The neighbor RSTP peer on this link is not able to detect our presence. - downstreamLoopDetected :A loop is detected on this link. |
| G32 sapTlsStpForwardTransitions | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.10 | Gauge32 | read-only | The value of the object sapTlsStpForwardTransitions indicates the number of times this port has transitioned from the Learning state to the Forwarding state. |
| G32 sapTlsStpInBadBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.13 | Gauge32 | read-only | This object specifies the number of bad BPDUs received on this SAP. |
| G32 sapTlsStpInConfigBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.11 | Gauge32 | read-only | The value of the object sapTlsStpInConfigBpdus indicates the number of Configuration BPDUs received on this SAP. |
| G32 sapTlsStpInMstBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.47 | Gauge32 | read-only | The value of the object sapTlsStpInMstBpdus indicates the number of Multiple Spanning Tree (MST) BPDUs received on this SAP. |
| G32 sapTlsStpInRstBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.29 | Gauge32 | read-only | The value of the object sapTlsStpInRstBpdus indicates the number of Rapid Spanning Tree (RST) BPDUs received on this SAP. |
| T/F sapTlsStpInsideRegion | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.45 | TruthValue | read-only | The value of the object sapTlsStpInsideRegion indicates whether the network connected to the SAP is in the same MST region. It corresponds to the parameter 'infoInternal' in 802.1Q. |
| G32 sapTlsStpInTcnBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.12 | Gauge32 | read-only | The value of the object sapTlsStpInTcnBpdus indicates the number of Topology Change Notification BPDUs received on this SAP. |
| INT sapTlsStpOperBpduEncap | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.16 | INTEGER | read-only | The value of the object sapTlsStpOperBpduEncap indicates the operating encapsulation type used on BPDUs sent out and received on this SAP. |
| T/F sapTlsStpOperEdge | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.24 | TruthValue | read-only | The value of the object sapTlsStpOperEdge indicates the operational value of the Edge Port parameter. The object is initialized to the value of sapTlsStpRapidStart and is set FALSE on reception of a BPDU. |
| STP sapTlsStpOperProtocol | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.28 | StpProtocol | read-only | sapTlsStpOperProtocol indicates whether stp, rstp or mstp is running on this SAP. If the protocol is not enabled on this SAP, the value notApplicable is returned. |
| G32 sapTlsStpOutConfigBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.14 | Gauge32 | read-only | The value of the object sapTlsStpOutConfigBpdus indicates the number of Configuration BPDUs sent out this SAP. |
| G32 sapTlsStpOutMstBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.48 | Gauge32 | read-only | The value of the object sapTlsStpOutMstBpdus indicates the number of Multiple Spanning Tree (MST) BPDUs sent out on this SAP. |
| G32 sapTlsStpOutRstBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.30 | Gauge32 | read-only | The value of the object sapTlsStpOutRstBpdus indicates the number of Rapid Spanning Tree (RST) BPDUs sent out on this SAP. |
| G32 sapTlsStpOutTcnBpdus | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.15 | Gauge32 | read-only | This object specifies the number of Topology Change Notification BPDUs sent out this SAP. |
| INT sapTlsStpPathCost | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.4 | INTEGER | read-write | The value of the object sapTlsStpPathCost specifies the contribution of this port to the path cost of paths towards the spanning tree root which include this port. |
| INT sapTlsStpPortNum | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.3 | INTEGER | read-write | The value of the object sapTlsStpPortNum specifies the value of the port number field which is contained in the least significant 12 bits of the 16-bit Port ID associated with this SAP. Values in the range 2048..4094 are automatically assigned by the agent when the SAP is created or when the value of this object is set to zero via management. Values in the range 1..2047 can be set via management, to allow this object to have a deterministic value across system reboots. |
| STP sapTlsStpPortRole | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.26 | StpPortRole | read-only | sapTlsStpPortRole indicates the current role of the sap as defined by the Rapid Spanning Tree Protocol. |
| TST sapTlsStpPortState | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.7 | TStpPortState | read-only | The value of the object sapTlsStpPortState indicates the port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the 'broken' state. |
| INT sapTlsStpPriority | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.2 | INTEGER | read-write | The value of the object sapTlsStpPriority specifies the value of the port priority field which is contained in the most significant 4 bits of the 16-bit Port ID associated with this SAP. As only the most significant 4 bits of the value are used, the actual value of this object is limited to multiples of 16: e.g. the agent rounds down the value to one of: 0, 16, 32, .. , 224, 240. |
| TMN sapTlsStpRapidStart | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.5 | TmnxEnabledDisabled | read-write | The value of the object sapTlsStpRapidStart specifies whether Rapid Start is enabled on this SAP. When the value is 'enabled' the Spanning Tree Protocol state transitions on this SAP are driven by the value of the 'HelloTime' instead of the value of 'ForwardDelay', thus allowing a faster transition into the forwarding state. This parameter is also referred to as 'adminEdge'. |
| T/F sapTlsStpRootGuard | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.44 | TruthValue | read-write | The value of the object sapTlsStpRootGuard specifies whether this port is allowed to become STP root port. It corresponds to the parameter 'restrictedRole' in 802.1Q. If set, it can cause lack of spanning tree connectivity. |
| T/F sapTlsStpRootGuardViolation | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.52 | TruthValue | read-only | The value of the object sapTlsStpRootGuardViolation indicates whether there is a root-guard violation at the present time. This can only happen when sapTlsStpRootGuard is set to true. |
| BRI sapTlsStpRxdDesigBridge | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.51 | BridgeId | read-only | The value of the object sapTlsStpRxdDesigBridge indicates the designated Bridge Identifier in the last BPDU which was received on this SAP. It identifies which bridge is connected to the SAP. |
| VPN sapTlsVpnId | 1.3.6.1.4.1.6527.3.1.2.4.3.3.1.17 | VpnId | read-only | The value of the object sapTlsVpnId indicates the VPN ID of the associated service. |
| sapTodMonitorEntry | 1.3.6.1.4.1.6527.3.1.2.4.3.26.1 | not-accessible | Information about ToD policy modifiable config data for a SAP. | |
| sapTodMonitorTable | 1.3.6.1.4.1.6527.3.1.2.4.3.26 | not-accessible | This table contains information on configurable objects on SAP level, that can be modified by a scheduled policy. | |
| TNA sapTodSuite | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.32 | TNamedItemOrEmpty | read-create | The value of the object sapTodSuite specifies the Time of Day (ToD) suite to be applied on this SAP. An empty string indicates that no ToD suite is applied on this SAP. A set request will only be allowed, if the indicated suite is defined in TIMETRA-SCHEDULER-MIB::tmnxTodSuiteTable. |
| sapTraps | 1.3.6.1.4.1.6527.3.1.3.4.3.0 | |||
| sapTrapsPrefix | 1.3.6.1.4.1.6527.3.1.3.4.3 | |||
| SER sapType | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.4 | ServType | read-only | This object indicates the type of service where this SAP is defined. |
| VPN sapVpnId | 1.3.6.1.4.1.6527.3.1.2.4.3.2.1.19 | VpnId | read-only | The VPN ID of the associated service. |
| STR svcManagedSapCreationError | 1.3.6.1.4.1.6527.3.1.2.4.3.100.3 | DisplayString | accessible-for-notify | The value of the object svcManagedSapCreationError indicates the reason why the system was unable to create the managed SAP. |
| timetraSvcSapMIBModule | 1.3.6.1.4.1.6527.1.1.3.55 | This document is the SNMP MIB module to manage and provision the various services of the Alcatel 7x50 SR system. Copyright 2003-2008 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel's proprietary intellectual property. Alcatel retains all title and ownership in the Specification, including any revisions. Alcatel grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied `as is', and Alcatel makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| tmnxSap7450V6v0Compliance | 1.3.6.1.4.1.6527.3.1.1.4.3.1.100 | The compliance statement for management of services SAPs on Alcatel 7450 ESS series systems. | ||
| tmnxSap7710V6v0Compliance | 1.3.6.1.4.1.6527.3.1.1.4.3.1.102 | The compliance statement for management of services SAPs on Alcatel 7710 SR series systems. | ||
| tmnxSap7750V6v0Compliance | 1.3.6.1.4.1.6527.3.1.1.4.3.1.101 | The compliance statement for management of services SAPs on Alcatel 7750 SR series systems. | ||
| tmnxSapAtmV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.102 | The group of objects supporting management of Sap ATM capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapBaseV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.103 | The group of objects supporting management of Sap Base capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapBsxV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.119 | The group of objects supporting management of BSX (Application Assurance) capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapCemNotificationV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.401 | The group of notifications supporting the CEM Sap feature on Alcatel 7710 SR series systems. | ||
| tmnxSapCemV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.112 | The group of objects supporting management of Sap Cem capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapCompliances | 1.3.6.1.4.1.6527.3.1.1.4.3.1 | |||
| tmnxSapConformance | 1.3.6.1.4.1.6527.3.1.1.4.3 | |||
| tmnxSapDhcpV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.106 | The group of objects supporting management of Sap TLS DHCP capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapGroups | 1.3.6.1.4.1.6527.3.1.1.4.3.2 | |||
| tmnxSapIppipeV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.110 | The group of objects supporting management of Sap I-Pipe capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapIpV6FilterV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.118 | The group of objects supporting management of Sap Ingress Policy capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapL2ptV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.113 | The group of objects supporting management of Sap TLS L2pt capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapMrpV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.115 | The group of objects supporting management of Sap MRP capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapMsapV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.114 | The group of objects supporting management of managed SAP capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapMstiV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.109 | The group of objects supporting management of Sap TLS MSTI capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapNotificationObjV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.200 | The group of objects supporting management of notifications on Alcatel 7x50 SR series systems. | ||
| tmnxSapNotifyGroup | 1.3.6.1.4.1.6527.3.1.1.4.3.2.400 | The group of obsolete notifications for the Sap feature on Alcatel 7x50 SR series systems. | ||
| tmnxSapNotifyObjs | 1.3.6.1.4.1.6527.3.1.2.4.3.100 | |||
| tmnxSapObjs | 1.3.6.1.4.1.6527.3.1.2.4.3 | |||
| tmnxSapObsoletedNotifyGroup | 1.3.6.1.4.1.6527.3.1.1.4.3.2.402 | The group of obsolete notifications for the Sap feature on Alcatel 7x50 SR series systems. | ||
| tmnxSapObsoletedV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.300 | The group of obsolete objects for the services feature on Alcatel 7x50 SR series systems. | ||
| tmnxSapPolicyV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.111 | The group of objects supporting management of Sap ingress/egress capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapPortIdV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.107 | The group of objects supporting management of Sap Port ID capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapQosV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.104 | The group of objects supporting management of Sap Ingress/Egress QoS capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapStaticHostV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.105 | The group of objects supporting management of Sap static host capabilities on Alcatel 7x50 SR series systems. | ||
| NTF tmnxSapStpExcepCondStateChng | 1.3.6.1.4.1.6527.3.1.3.4.5.0.37 | The tmnxSapStpExcepCondStateChng notification is generated when the value of the object sapTlsStpException has changed, i.e. when the exception condition changes on the indicated SAP. | ||
| tmnxSapSubMgmtV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.108 | The group of objects supporting management of Sap Sub-management capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapTlsV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.101 | The group of objects supporting management of Sap TLS capabilities on Alcatel 7x50 SR series systems. | ||
| tmnxSapV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.100 | The group of objects supporting management of Sap general capabilities on Alcatel 7x50 SR series systems. | ||
| NTF tmnxStpRootGuardViolation | 1.3.6.1.4.1.6527.3.1.3.4.5.0.35 | The tmnxStpRootGuardViolation notification is generated when a SAP which has root-guard configured is trying to become root (has a better STP priority vector). The SAP will become alternate and traffic will be blocked. | ||
| tmnxTlsMsapPppoeV6v0Group | 1.3.6.1.4.1.6527.3.1.1.4.3.2.117 | The group of objects supporting PPPOE on Managed SAPs feature on the Alcatel 7x50 SR series systems. | ||
| NTF topologyChangeSapMajorState | 1.3.6.1.4.1.6527.3.1.3.4.5.0.1 | The topologyChangeSapMajorState notification is generated when a SAP has transitioned its state from learning to forwarding or from forwarding to blocking or broken. The spanning tree topology has been modified and it may denote loss of customer access or redundancy. Check the new topology against the provisioned topology to determine the severity of connectivity loss. | ||
| NTF topologyChangeSapState | 1.3.6.1.4.1.6527.3.1.3.4.5.0.5 | The topologyChangeSapState notification is generated when a SAP has transitioned state to blocking or broken from a state other than forwarding. This event complements what is not covered by topologyChangeSapMajorState. The spanning tree topology has been modified and it may denote loss of customer access or redundancy. Check the new topology against the provisioned topology to determine severity of connectivity loss. |
RFC description
Nokia/Alcatel proprietary MIB (last updated Release 25, Feb 2025) for managing service access point (SAP) objects on SROS network devices.
Start monitoring Nokia/Alcatel-Lucent 7x50 Service Router family, entire product line (Service Access Point admin/oper status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.