All MIBs › CLARENT-MIB
Category: Telephony/VoIP
Description: Manages Clarent VoIP gateway configuration, call routing, and telephony performance metrics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CLARENT-MIB?
CLARENT-MIB is a vendor MIB from Clarent Corporation for managing its VoIP gateway product line, covering gateway configuration, call routing behavior, and telephony performance metrics. Given the vendor's VoIP gateway focus, its data categories likely span device/service configuration, call-processing statistics, and possibly trap-based fault notifications, though no module description or sample objects were provided to confirm specifics. In a monitoring context, such a MIB would typically be used to check gateway software/service status (e.g., call routing tables and call success/failure statistics) more than classic hardware sensors, since VoIP gateway health is largely judged by call quality and completion metrics. No dependency information is available from the provided material. It would be deployed on Clarent VoIP gateways within a carrier or enterprise voice network, likely alongside signaling protocols like H.323 or SIP. Engineers can download the CLARENT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CLARENT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Clarent VoIP gateway
Monitoring Examples
No sample object names were supplied for this MIB, so a concrete polling scenario cannot be honestly constructed; based on the short description alone, an admin would be expected to monitor call routing configuration and telephony performance counters (e.g., call volume or failure rates) on the gateway, but specific table/object names are not available to cite.
What Can Be Monitored
- call routing configuration
- telephony performance metrics
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| IpAddress | |
| NetworkAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| STR abortCommand | 1.3.6.1.4.1.2858.100.1.8 | DisplayString | read-write | Initiate an ABORT command. In the SET command, specify the package name. |
| INT abortError | 1.3.6.1.4.1.2858.100.1.2.1.20 | INTEGER | read-only | Package abort error |
| STR abortMessage | 1.3.6.1.4.1.2858.100.1.2.1.19 | DisplayString | read-only | Package abort status message |
| INT abortStatus | 1.3.6.1.4.1.2858.100.1.2.1.18 | INTEGER | read-only | Package abort status |
| INT autoCAMRestart | 1.3.6.1.4.1.2858.100.4.6 | INTEGER | read-write | Enable SNMP Agent to automatically restart the CAM |
| INT autoCCRestart | 1.3.6.1.4.1.2858.100.4.2 | INTEGER | read-write | Enable SNMP Agent to automatically restart the GW |
| INT autoDMRestart | 1.3.6.1.4.1.2858.100.4.4 | INTEGER | read-write | Enable SNMP Agent to automatically restart the DM |
| INT autoGKRestart | 1.3.6.1.4.1.2858.100.4.5 | INTEGER | read-write | Enable SNMP Agent to automatically restart the GK |
| INT autoGWRestart | 1.3.6.1.4.1.2858.100.4.1 | INTEGER | read-write | Enable SNMP Agent to automatically restart the GW |
| INT autoTPRestart | 1.3.6.1.4.1.2858.100.4.3 | INTEGER | read-write | Enable SNMP Agent to automatically restart the GW |
| INT avgHoldTime | 1.3.6.1.4.1.2858.8.2.1.4 | INTEGER | read-only | Average time per call on the port |
| STR baseURL | 1.3.6.1.4.1.2858.100.1.10 | DisplayString | read-write | Use this variable to set/get the BASE URL, which is a well-known URL identifying the location from which packages are downloaded. |
| INT buildMajorVersion | 1.3.6.1.4.1.2858.100.5.1.1.4 | INTEGER | read-only | Build Major Release Version Number |
| INT buildMinorVersion | 1.3.6.1.4.1.2858.100.5.1.1.5 | INTEGER | read-only | Major Release Version Number |
| NTF callRatingFailed | 1.3.6.1.4.1.2858.4.0.9918 | Call rating failed | ||
| ccControl | 1.3.6.1.4.1.2858.7 | |||
| STR ccControlval | 1.3.6.1.4.1.2858.7.1 | DisplayString | read-write | Controls Clarent Command Center |
| NTF ccCreditSChg | 1.3.6.1.4.1.2858.4.0.9930 | Clarent Connect credit status changed | ||
| NTF ccIsDown | 1.3.6.1.4.1.2858.4.0.9904 | Clarent Command Center is down | ||
| INT ccOperState | 1.3.6.1.4.1.2858.2.2 | INTEGER | read-only | State of the CC, enabled means running, disabled means not running |
| INT ccPortNumber | 1.3.6.1.4.1.2858.100.3.2.2 | INTEGER | read-write | Port number of the Command Center for the Clarent ThroughPacket server |
| ccreadvars | 1.3.6.1.4.1.2858.2 | |||
| STR ccStatus | 1.3.6.1.4.1.2858.2.1 | DisplayString | read-only | Clarent Command Center status |
| NTF cDiskSpaceLow | 1.3.6.1.4.1.2858.4.0.9942 | Drive has less than 50MB of free space available. This trap is issued on an hourly basis if the condition persists. | ||
| cGatekeeper | 1.3.6.1.4.1.2858.100.20 | |||
| cGkConfig | 1.3.6.1.4.1.2858.100.20.2 | |||
| cGkStatisticsManagement | 1.3.6.1.4.1.2858.100.20.3 | |||
| cGkStatus | 1.3.6.1.4.1.2858.100.20.1 | |||
| clarent | 1.3.6.1.4.1.2858 | |||
| clarent_gktraps | 1.3.6.1.4.1.2858.100.20.100 | |||
| clarent_traps | 1.3.6.1.4.1.2858.4 | |||
| STR clarentcfg | 1.3.6.1.4.1.2858.6.6 | DisplayString | read-write | Private control field |
| NTF clarentInfo | 1.3.6.1.4.1.2858.4.0.9933 | Generic Clarent error trap: Severity: Critical(0), Major(1), Minor(2), Warning(3), or Information(4) Class: Configuration(0), Hardware(1), or Software(2) Number of trap Count of total number of traps per class Descriptive text string | ||
| INT clarentreserved | 1.3.6.1.4.1.2858.8.2.1.11 | INTEGER | read-only | Reserved |
| clearinghouse | 1.3.6.1.4.1.2858.5 | |||
| NTF clrHseCreditSChg | 1.3.6.1.4.1.2858.4.0.9929 | Clarent Connect clearinghouse credit status changed | ||
| NTF cNoConnectRoute | 1.3.6.1.4.1.2858.4.0.9943 | Clarent Connect partner does not have a route for this call. This trap is issued no more than once every 5 minutes. | ||
| STR commitCommand | 1.3.6.1.4.1.2858.100.1.7 | DisplayString | read-write | Initiate a COMMIT command. In the SET command, specify the package name. |
| INT commitError | 1.3.6.1.4.1.2858.100.1.2.1.17 | INTEGER | read-only | Package commit error |
| INT commitLevel | 1.3.6.1.4.1.2858.100.1.2.1.27 | INTEGER | read-write | Mode of operation in which the package was installed |
| STR commitMessage | 1.3.6.1.4.1.2858.100.1.2.1.16 | DisplayString | read-only | Package commit status message |
| INT commitStatus | 1.3.6.1.4.1.2858.100.1.2.1.15 | INTEGER | read-only | Package commit status |
| STR component | 1.3.6.1.4.1.2858.100.5.1.1.1 | DisplayString | read-only | Name of Clarent Component that is versioned |
| NTF connectCCFailed | 1.3.6.1.4.1.2858.4.0.9908 | Clarent Gateway cannot connect to the specified Command Center | ||
| INT connectedCalls | 1.3.6.1.4.1.2858.8.2.1.24 | INTEGER | read-only | Number of calls answered |
| NTF connectNoVoicePort | 1.3.6.1.4.1.2858.4.0.9914 | Clarent Gateway cannot connect to another gateway; not responding | ||
| cSysControl | 1.3.6.1.4.1.2858.100.6.2 | |||
| cSysManagement | 1.3.6.1.4.1.2858.100.6 | |||
| INT cSysOperation | 1.3.6.1.4.1.2858.100.6.2.1 | INTEGER | read-write | User can reboot the system by issuing an enableShutdown operation followed by a startShutdown operation. When the system is enabled for shutdown the clarent shutdowntrap is emitted, disableShutdown inhibits shutdown until an enableShutdown is received. Default state is Shutdown disabled |
| cSysStatus | 1.3.6.1.4.1.2858.100.6.1 | |||
| INT cSystemError | 1.3.6.1.4.1.2858.100.6.1.2 | INTEGER | read-only | Error Code reflected from system |
| INT cSystemStatus | 1.3.6.1.4.1.2858.100.6.1.1 | INTEGER | read-only | Current status of the Clarent Network Element, if state is shutdownAllowed it means that an enableShutdown down operation has been received. At this point a startShutdown operation would start the shutdown process, if opError then the csystemError will contain an error code |
| STR currentAni | 1.3.6.1.4.1.2858.8.2.1.28 | DisplayString | read-only | Current ANI, if the port is connected |
| STR currentDnis | 1.3.6.1.4.1.2858.8.2.1.29 | DisplayString | read-only | Current DNIS, if the port is connected |
| INT currentHoldTime | 1.3.6.1.4.1.2858.8.2.1.27 | INTEGER | read-only | Current hold time, in seconds, if the port is connected |
| INT currentValue | 1.3.6.1.4.1.2858.48.9 | INTEGER | read-only | The current value of the paramater that has exceeded or rearmed the threshHold in the ThreshHold Trap |
| INT datacount | 1.3.6.1.4.1.2858.8.2.1.17 | INTEGER | read-only | Number of data events on the port |
| NTF dbClerkStarted | 1.3.6.1.4.1.2858.4.0.9945 | A new database clerk was started. The value of trapNumber represents the total number of clerks running. | ||
| NTF dbError | 1.3.6.1.4.1.2858.4.0.9944 | Clarent DB error trap contains the following information Severity: Critical(0), Major(1), Minor(2), Warning(3), or Information(4) Database error number Descriptive error text string Count of total number of database error traps sent since machine power up | ||
| STR deleteCommand | 1.3.6.1.4.1.2858.100.1.11 | DisplayString | read-write | Initiate a DELETE command. In the SET command, specify the package name. |
| INT deleteError | 1.3.6.1.4.1.2858.100.1.2.1.26 | INTEGER | read-only | Package delete error |
| STR deleteMessage | 1.3.6.1.4.1.2858.100.1.2.1.25 | DisplayString | read-only | Package delete status message |
| INT deleteStatus | 1.3.6.1.4.1.2858.100.1.2.1.24 | INTEGER | read-only | Package delete status |
| NTF dialUpNoVoicePort | 1.3.6.1.4.1.2858.4.0.9913 | Clarent Gateway cannot dial number; no voice port is available | ||
| INT disablePort | 1.3.6.1.4.1.2858.6.8 | INTEGER | read-write | Disable the port passed in the varbind. For example, to disable port 11, set the value of this variable to 11. Setting the value of this variable to -1 disables all ports. |
| NTF dmIsDown | 1.3.6.1.4.1.2858.4.0.9948 | Clarent Distribution Service is down | ||
| NTF dmRestarted | 1.3.6.1.4.1.2858.4.0.9947 | Clarent Distribution Service restarted successfully | ||
| STR downLoadCommand | 1.3.6.1.4.1.2858.100.1.3 | DisplayString | read-write | Initiate a DOWNLOAD command. In the SET command, specify the package name. |
| INT downloadError | 1.3.6.1.4.1.2858.100.1.2.1.5 | INTEGER | read-only | Package download error |
| STR downloadMessage | 1.3.6.1.4.1.2858.100.1.2.1.4 | DisplayString | read-only | Package download status message |
| INT downloadStatus | 1.3.6.1.4.1.2858.100.1.2.1.3 | INTEGER | read-only | Package download status |
| INT egressCount | 1.3.6.1.4.1.2858.8.2.1.10 | INTEGER | read-only | Total number of egress calls on the port |
| INT egressTime | 1.3.6.1.4.1.2858.8.2.1.9 | INTEGER | read-only | Total egress time, in seconds, on the port |
| INT enablePort | 1.3.6.1.4.1.2858.6.7 | INTEGER | read-write | Enable the port passed in the varbind. For example, to enable port 9, set the value of this variable to 9. Setting the value of this variable to -1 enables all ports. |
| INT faxcount | 1.3.6.1.4.1.2858.8.2.1.15 | INTEGER | read-only | Total number of fax calls on the port |
| gateway | 1.3.6.1.4.1.2858.1 | |||
| NTF gatewayConnect | 1.3.6.1.4.1.2858.4.0.9915 | Clarent Gateway, at the specified IP address, connected to Command Center | ||
| NTF gatewayDisconnect | 1.3.6.1.4.1.2858.4.0.9916 | Clarent Gateway, at the specified IP address, disconnected from Command Center | ||
| NTF gatewayIsDown | 1.3.6.1.4.1.2858.4.0.9901 | Clarent Gateway is down | ||
| gatewayports | 1.3.6.1.4.1.2858.8 | |||
| STR gatewayStatus | 1.3.6.1.4.1.2858.1.1 | DisplayString | read-only | The number of ports currently in use, as well as the number of calls, call time, and hold time for each port (# sign-delimited string) |
| gatewaytable | 1.3.6.1.4.1.2858.9 | |||
| INT gkAdminState | 1.3.6.1.4.1.2858.100.20.2.20 | INTEGER | read-write | Command object to shut down Gatekeeper gracefully or forcefully |
| STR gkAltGKList | 1.3.6.1.4.1.2858.100.20.1.3 | DisplayString | read-only | Alternate gatekeeper list |
| INT gkAverageHoldTime | 1.3.6.1.4.1.2858.100.20.1.6.1.4 | INTEGER | read-only | Average hold time for calls of a given call port type |
| INT gkCallPortType | 1.3.6.1.4.1.2858.100.20.1.6.1.1 | INTEGER | read-only | List of call port types. Call port types are: TOTAL, a call from any combination of call port types H323H323, an H.323 gateway-to-H.323 gateway call H323CLARENT, an H.323 gateway-to IP H323NONE , an H.323 gateway call that was not successfully routed CLARENT2H323, a Clarent Gateway-to-H.323 gateway call CLARENT2CLARENT, a Clarent Gateway-Clarent Gateway call CLARENT2CLARENT, a Clarent Gateway call that was not successfully routed. |
| gkCallStatsEntry | 1.3.6.1.4.1.2858.100.20.1.6.1 | not-accessible | Entry in the CallStatsTable for a given call port type | |
| gkCallStatsTable | 1.3.6.1.4.1.2858.100.20.1.6 | not-accessible | List of call statistics for all call port types | |
| INT gkCallTime | 1.3.6.1.4.1.2858.100.20.1.6.1.3 | INTEGER | read-only | Amount of time, in seconds, for calls of a given call port type |
| INT gkCCCKeepAliveTimer | 1.3.6.1.4.1.2858.100.20.2.19 | INTEGER | read-write | How often, in seconds, Clarent Gatekeeper checks its connection with the Command Center. Default = 10, minimum = 5, maximum = 120 |
| INT gkCCConnState | 1.3.6.1.4.1.2858.100.20.1.5 | INTEGER | read-only | Gatekeeper-to-Command Center connection state |
| INT gkCCUDPPort | 1.3.6.1.4.1.2858.100.20.2.4 | INTEGER | read-write | UDP port through which Clarent Command Center communicates with Clarent Gatekeeper |
| STR gkDebugFilePath | 1.3.6.1.4.1.2858.100.20.2.8 | DisplayString | read-write | Path to Clarent Gatekeeper trace configuration file |
| NTF gkEndpointUnreachable | 1.3.6.1.4.1.2858.100.20.100.0.8 | Endpoint stopped sending keepalive messages to Clarent Gatekeeper | ||
| NTF gkEndPointURQFailed | 1.3.6.1.4.1.2858.100.20.100.0.9 | Endpoint attempted to unregister but has active calls | ||
| IP gkExternalIPAddr | 1.3.6.1.4.1.2858.100.20.2.3 | IpAddress | read-write | IP address by which Clarent Gatekeeper is known to outside entities |
| INT gkGracefulShutdownPeriod | 1.3.6.1.4.1.2858.100.20.2.21 | INTEGER | read-write | Number of minutes to wait before shutting down Clarent Gatekeeper gracefully |
| STR gkGroup | 1.3.6.1.4.1.2858.100.20.2.16 | DisplayString | read-write | Group to which Clarent Gatekeeper belongs |
| IP gkIPAddr | 1.3.6.1.4.1.2858.100.20.2.2 | IpAddress | read-write | IP address of Clarent Gatekeeper |
| NTF gkIsDown | 1.3.6.1.4.1.2858.100.20.100.0.1 | Clarent Gatekeeper is down | ||
| NTF gkIsRejectingRasMsg | 1.3.6.1.4.1.2858.100.20.100.0.7 | Clarent Gatekeeper started rejecting H.225 RAS messages. Clarent::For Future Release | ||
| INT gkLoadState | 1.3.6.1.4.1.2858.100.20.1.4 | INTEGER | read-only | Clarent Gatekeeper load state |
| NTF gkLoadStateCritical | 1.3.6.1.4.1.2858.100.20.100.0.6 | Clarent Gatekeeper load state is critical. Load states are: Minimal (0), Light (1), Medium (2), Heavy (3), Dangerously Heavy (4), and Critical (5). | ||
| STR gkLogFileAppendString | 1.3.6.1.4.1.2858.100.20.2.11 | DisplayString | read-write | Character string to append to Clarent Gatekeeper log file names |
| STR gkLogFileDir | 1.3.6.1.4.1.2858.100.20.2.10 | DisplayString | read-write | Directory in which Clarent Gatekeeper saves log files |
| INT gkLogFileEnable | 1.3.6.1.4.1.2858.100.20.2.9 | INTEGER | read-write | Enable or disable file logging |
| INT gkLogFileMaxNumFiles | 1.3.6.1.4.1.2858.100.20.2.13 | INTEGER | read-write | Maximum number of log files Clarent Gatekeeper creates before overwriting existing logs |
| INT gkLogFileRolloverSize | 1.3.6.1.4.1.2858.100.20.2.12 | INTEGER | read-write | Size, in kilobytes, to which Clarent Gatekeeper allows a log file to grow before closing a log and starting another |
| STR gkName | 1.3.6.1.4.1.2858.100.20.2.1 | DisplayString | read-write | Clarent Gatekeeper name |
| NTF gkNotRegistered | 1.3.6.1.4.1.2858.100.20.100.0.4 | Clarent Gatekeeper cannot register with the Command Center | ||
| INT gkNumberOfCalls | 1.3.6.1.4.1.2858.100.20.1.6.1.2 | INTEGER | read-only | Number of call attempts for a given call port type |
| INT gkNumberOfConnectedCalls | 1.3.6.1.4.1.2858.100.20.1.6.1.5 | INTEGER | read-only | Number of call completions for a given call port type |
| INT gkOpState | 1.3.6.1.4.1.2858.100.20.1.2 | INTEGER | read-only | Clarent Gatekeeper operational state |
| NTF gkOpStateChg | 1.3.6.1.4.1.2858.100.20.100.0.5 | Clarent Gatekeeper changed operational state. Operational states are: disabled (0), enabled (1). | ||
| INT gkPortInUseCount | 1.3.6.1.4.1.2858.100.20.1.1 | INTEGER | read-only | Number of ports currently in use |
| IP gkPrimaryCCCIPAddr | 1.3.6.1.4.1.2858.100.20.2.5 | IpAddress | read-write | IP address of primary Command Center |
| INT gkPriority | 1.3.6.1.4.1.2858.100.20.2.17 | INTEGER | read-write | Priority of this Clarent Gatekeeper in the alternate gatekeeper list |
| INT gkRasKeepAliveTimer | 1.3.6.1.4.1.2858.100.20.2.18 | INTEGER | read-write | Amount of time, in seconds, that an H.323 gateway must register with Clarent Gatekeeper. Default = 25, miniumum = 0, maximum = 120. |
| NTF gkRestarted | 1.3.6.1.4.1.2858.100.20.100.0.3 | Clarent Gatekeeper restarted successfully | ||
| NTF gkRestartFailed | 1.3.6.1.4.1.2858.100.20.100.0.2 | Clarent Gatekeeper failed to restart | ||
| IP gkSecCCCIPAddr | 1.3.6.1.4.1.2858.100.20.2.6 | IpAddress | read-write | IP address of secondary Command Center |
| STR gkServiceLpdFilePath | 1.3.6.1.4.1.2858.100.20.2.7 | DisplayString | read-write | Location of telephone user interface, or Line Port Director (LPD) file |
| INT gkSysLogEnable | 1.3.6.1.4.1.2858.100.20.2.14 | INTEGER | read-write | Enable or disable logging to a system logging (syslog) daemon process running on another computer |
| IP gkSysLogIpAddr | 1.3.6.1.4.1.2858.100.20.2.15 | IpAddress | read-write | IP address of a system logging (syslog) daemon server |
| NTF gwAppShutdown | 1.3.6.1.4.1.2858.4.0.9927 | Clarent Gateway shut down | ||
| INT gwBoardType | 1.3.6.1.4.1.2858.1.8 | INTEGER | read-only | Type of boards loaded in Gateway |
| gwControl | 1.3.6.1.4.1.2858.6 | |||
| STR gwControlVal | 1.3.6.1.4.1.2858.6.1 | DisplayString | read-write | Controls Clarent Gateway |
| INT gwEnableStats | 1.3.6.1.4.1.2858.100.2.1 | INTEGER | read-write | Enables statistics messages from the gateway to the Command Center. Specify a value of 1 to enable statistics. The default value is 0 (zero), which disables statistics. |
| gwEntry | 1.3.6.1.4.1.2858.9.2.1 | not-accessible | Clarent Gateway entry | |
| INT gwId | 1.3.6.1.4.1.2858.9.2.1.1 | INTEGER | read-only | A unique number for each Clarent Gateway |
| NTF gwNotRegistered | 1.3.6.1.4.1.2858.4.0.9917 | Clarent Gateway is not registered | ||
| INT gwNumAttached | 1.3.6.1.4.1.2858.9.1 | INTEGER | read-only | The number of Clarent Gateways currently connected to the Command Center |
| STR gwnumberOfCalls | 1.3.6.1.4.1.2858.1.3 | DisplayString | read-only | Number of calls per port (comma-delimited string) |
| INT gwNumBoards | 1.3.6.1.4.1.2858.1.9 | INTEGER | read-only | Number of boards loaded in Gateway |
| INT gwNumPhysicalPorts | 1.3.6.1.4.1.2858.8.1 | INTEGER | read-only | Number of physical gateway ports present on this system (regardless of their current states) |
| INT gwOperState | 1.3.6.1.4.1.2858.1.7 | INTEGER | read-only | State of the GW, enabled means running, disabled means not running |
| gwPortEntry | 1.3.6.1.4.1.2858.8.2.1 | not-accessible | The status of a port | |
| INT gwPortsPerFirstSpan | 1.3.6.1.4.1.2858.1.10 | INTEGER | read-only | number of ports on the first span in a multi-span board |
| INT gwPortsPerSpan | 1.3.6.1.4.1.2858.1.11 | INTEGER | read-only | number of ports on a span in a multi-span board |
| OCT gwPortStatusList | 1.3.6.1.4.1.2858.1.13 | OCTET STRING | read-only | returns an OCTET string of length equal to the number of ports in the system. Each byte indicates the status of the port at that offset. That values are identical to the portStatus Value defined in the Port Table below |
| gwPortTable | 1.3.6.1.4.1.2858.8.2 | not-accessible | A list of gateway port entries. The number of usable ports is governed by the number of licensed ports. | |
| INT gwSpansPerBoard | 1.3.6.1.4.1.2858.1.12 | INTEGER | read-only | number of spans on a board |
| gwStatisticsManagement | 1.3.6.1.4.1.2858.100.2 | |||
| INT gwStatsInterval | 1.3.6.1.4.1.2858.100.2.2 | INTEGER | read-write | Interval, in minutes, between gateway statistic messages from the gateway to the Command Center |
| gwTable | 1.3.6.1.4.1.2858.9.2 | not-accessible | A list of Clarent Gateway entries | |
| gwtrafficstats | 1.3.6.1.4.1.2858.10 | |||
| INT hangupPort | 1.3.6.1.4.1.2858.6.9 | INTEGER | read-write | Hang up the port passed in the varbind. For example, to hang up port 10, set the value of this variable to 10. Setting the value of this variable to -1 hangs up all ports. |
| INT ingressCount | 1.3.6.1.4.1.2858.8.2.1.8 | INTEGER | read-only | Total number of ingress calls on the port |
| INT ingressTime | 1.3.6.1.4.1.2858.8.2.1.7 | INTEGER | read-only | Total ingress time, in seconds, on the port |
| INT inServerTable | 1.3.6.1.4.1.2858.9.2.1.3 | INTEGER | read-only | Whether the gateway is in the SERVER-INFO table |
| STR installCommand | 1.3.6.1.4.1.2858.100.1.5 | DisplayString | read-write | Initiate an INSTALL command. In the SET command, specify the package name. |
| INT installError | 1.3.6.1.4.1.2858.100.1.2.1.11 | INTEGER | read-only | Package install error |
| STR installMessage | 1.3.6.1.4.1.2858.100.1.2.1.10 | DisplayString | read-only | Package install status message |
| INT installStatus | 1.3.6.1.4.1.2858.100.1.2.1.9 | INTEGER | read-only | Package install status |
| NTF invalidCCLicense | 1.3.6.1.4.1.2858.4.0.9919 | Invalid Command Center license | ||
| INT ipPortLocMState | 1.3.6.1.4.1.2858.8.2.1.22 | INTEGER | read-only | Local maintenance state of the IP connection between gateways |
| INT ipPortRemMState | 1.3.6.1.4.1.2858.8.2.1.23 | INTEGER | read-only | Remote maintenance state of the IP connection between gateways. |
| INT ipPortState | 1.3.6.1.4.1.2858.8.2.1.21 | INTEGER | read-only | IP port state |
| NTF licRollBack | 1.3.6.1.4.1.2858.4.0.9932 | Clarent Command Center license key change rolled back | ||
| INT linePortLocMState | 1.3.6.1.4.1.2858.8.2.1.19 | INTEGER | read-only | Local maintenance state of the telephone line to the port |
| INT linePortRemMState | 1.3.6.1.4.1.2858.8.2.1.20 | INTEGER | read-only | Remote maintenance state of the telephone line to the port |
| INT linePortState | 1.3.6.1.4.1.2858.8.2.1.18 | INTEGER | read-only | Line port state |
| STR loadCommand | 1.3.6.1.4.1.2858.100.1.9 | DisplayString | read-write | Initiate a LOAD command. In the SET command, specify the package name. |
| INT loadError | 1.3.6.1.4.1.2858.100.1.2.1.23 | INTEGER | read-only | Package load error |
| STR loadMessage | 1.3.6.1.4.1.2858.100.1.2.1.22 | DisplayString | read-only | Package load status message |
| INT loadStatus | 1.3.6.1.4.1.2858.100.1.2.1.21 | INTEGER | read-only | Package load status |
| NTF lostCC | 1.3.6.1.4.1.2858.4.0.9907 | Clarent Gateway lost its connection to the specified Command Center | ||
| INT majorVersion | 1.3.6.1.4.1.2858.100.5.1.1.2 | INTEGER | read-only | Major Release Version Number |
| mgt | 1.3.6.1.4.1.2858.100 | |||
| INT minorVersion | 1.3.6.1.4.1.2858.100.5.1.1.3 | INTEGER | read-only | Minor Release Version Number |
| NTF numberIntercept | 1.3.6.1.4.1.2858.4.0.9935 | Call placed to the intercept number | ||
| INT numberOfCalls | 1.3.6.1.4.1.2858.8.2.1.3 | INTEGER | read-only | Number of calls made on the port |
| INT numPackages | 1.3.6.1.4.1.2858.100.1.1 | INTEGER | read-only | Number of packages on a Clarent Network Element. |
| packageEntry | 1.3.6.1.4.1.2858.100.1.2.1 | not-accessible | Package status entry | |
| packageManagement | 1.3.6.1.4.1.2858.100.1 | |||
| STR packageName | 1.3.6.1.4.1.2858.100.1.2.1.1 | DisplayString | read-only | Unique name of the package |
| INT packageOperation | 1.3.6.1.4.1.2858.100.1.99999 | INTEGER | read-write | List of allowed package operations |
| INT packageStatus | 1.3.6.1.4.1.2858.100.1.2.1.2 | INTEGER | read-only | Package status |
| packageTable | 1.3.6.1.4.1.2858.100.1.2 | not-accessible | A list of package entries | |
| NTF pinSuspended | 1.3.6.1.4.1.2858.4.0.9952 | An account was suspended | ||
| STR portCallTime | 1.3.6.1.4.1.2858.1.4 | DisplayString | read-only | Call time per port (comma-delimited string) |
| STR portHoldTime | 1.3.6.1.4.1.2858.1.5 | DisplayString | read-only | Hold time per port (comma-delimited string) |
| INT portIndex | 1.3.6.1.4.1.2858.8.2.1.1 | INTEGER | read-only | A unique number for each port, ranging from 0 (zero) to the number of physical ports |
| NTF portInService | 1.3.6.1.4.1.2858.4.0.9912 | Clarent Gateway port is back in service | ||
| INT portInUseCount | 1.3.6.1.4.1.2858.1.2 | INTEGER | read-only | Number of ports currently in use |
| NTF portOutOfService | 1.3.6.1.4.1.2858.4.0.9911 | Clarent Gateway port is out of service | ||
| INT portStatus | 1.3.6.1.4.1.2858.8.2.1.2 | INTEGER | read-only | Port state |
| STR prepareCommand | 1.3.6.1.4.1.2858.100.1.6 | DisplayString | read-write | Initiate a PREPARE command. In the SET command, specify the package name. |
| INT prepareError | 1.3.6.1.4.1.2858.100.1.2.1.14 | INTEGER | read-only | Package prepare error |
| STR prepareMessage | 1.3.6.1.4.1.2858.100.1.2.1.13 | DisplayString | read-only | Package prepare status message |
| INT prepareStatus | 1.3.6.1.4.1.2858.100.1.2.1.12 | INTEGER | read-only | Package prepare status |
| STR priCCIPAddress | 1.3.6.1.4.1.2858.100.3.2.1 | DisplayString | read-write | IP address of the primary Command Center for the Clarent ThroughPacket server |
| procManagement | 1.3.6.1.4.1.2858.100.4 | |||
| rdc | 1.3.6.1.4.1.2858.3 | |||
| STR rdcStatus | 1.3.6.1.4.1.2858.3.1 | DisplayString | read-only | Roaming Domain Controller status |
| NTF rebootCommand | 1.3.6.1.4.1.2858.4.0.9941 | The system has been enabled to receive a startShutdown command | ||
| INT recvCount | 1.3.6.1.4.1.2858.8.2.1.6 | INTEGER | read-only | |
| INT remoteChannel | 1.3.6.1.4.1.2858.8.2.1.25 | INTEGER | read-only | Port number on the remote gateway, if the port is connected |
| INT remoteGWId | 1.3.6.1.4.1.2858.8.2.1.26 | INTEGER | read-only | ID of the remote gateway, if the port is connected |
| NTF resettingDSPBrd | 1.3.6.1.4.1.2858.4.0.9928 | Resetting DSP board | ||
| NTF restartCCFailed | 1.3.6.1.4.1.2858.4.0.9906 | Clarent Command Center failed to restart | ||
| NTF restartCCSuccess | 1.3.6.1.4.1.2858.4.0.9905 | Clarent Command Center restarted successfully | ||
| NTF restartDMFailed | 1.3.6.1.4.1.2858.4.0.9946 | Clarent Distribution Service failed to restart | ||
| NTF restartGWFailed | 1.3.6.1.4.1.2858.4.0.9903 | Clarent Gateway failed to restart | ||
| NTF restartGWSuccess | 1.3.6.1.4.1.2858.4.0.9902 | Clarent Gateway restarted successfully | ||
| NTF restartTPFailed | 1.3.6.1.4.1.2858.4.0.9937 | Clarent ThroughPacket server failed to restart | ||
| STR secCCIPAddress | 1.3.6.1.4.1.2858.100.3.2.3 | DisplayString | read-write | IP address of the secondary Command Center for the Clarent ThroughPacket server |
| IP serverIpAddr | 1.3.6.1.4.1.2858.9.2.1.2 | IpAddress | read-only | IP Address of the Clarent Gateway |
| NTF sigGWMTPPause | 1.3.6.1.4.1.2858.4.0.9949 | The Message Transfer Protocol paused | ||
| NTF sigGWMTPResume | 1.3.6.1.4.1.2858.4.0.9950 | The Message Transfer Protocol resumed | ||
| NTF sigGWTaskActive | 1.3.6.1.4.1.2858.4.0.9951 | A signaling task started | ||
| NTF softwareUpdate | 1.3.6.1.4.1.2858.4.0.9934 | Software update: Name of package Package operation: Download(0), Unpack(1), Install(2), Prepare(3), Commit(4), Abort(5), Delete(8) Package operation status Error count | ||
| NTF ss7LinkDown | 1.3.6.1.4.1.2858.4.0.9922 | SS7 link is down | ||
| NTF ss7LinkUp | 1.3.6.1.4.1.2858.4.0.9921 | SS7 link is up | ||
| NTF systemReboot | 1.3.6.1.4.1.2858.4.0.9940 | The system is rebooting in response to a startShutdown command | ||
| INT threshHoldAction | 1.3.6.1.4.1.2858.48.10 | INTEGER | read-only | ThreshHold Action |
| STR threshHoldName | 1.3.6.1.4.1.2858.48.7 | DisplayString | read-only | Name of the Threshold Package being reported on in a ThreshHold Trap |
| NTF threshHoldTrap | 1.3.6.1.4.1.2858.4.0.9939 | Clarent ThreshHold Trap, indicates that a particular Threshold has been exceeded or rearmed by the named Application. This trap contains 1) The Severity of the Threshold (Critical, Major, Minor, Warning, Information) 2) the name of the Application (e.g. ThroughPacket) 3) the ThreshHold Name (e.g. PacketsperSecond, BytesPerSecond ) 4) the ThreshHold Value that was exceeded/rearmed ( e.g. 350000 ) 5) the current value of the variable being sampled. ( e.g. BytesPerSecond 355043 ) 6) the Action, Exceeded or Rearmed. Thresholds are rearmed when the moving average of the variable being measured is at 75% of the ThreshHold. | ||
| INT threshHoldValue | 1.3.6.1.4.1.2858.48.8 | INTEGER | read-only | The ThreshHoldValue That is being exceeded or rearmed |
| throughPacket | 1.3.6.1.4.1.2858.100.3 | |||
| INT totalConnectCall | 1.3.6.1.4.1.2858.10.15 | INTEGER | read-only | Total number of ingress calls that were terminated at a remote gateway |
| INT totalDataCount | 1.3.6.1.4.1.2858.10.12 | INTEGER | read-only | Total number of data events |
| INT totalDataTime | 1.3.6.1.4.1.2858.10.11 | INTEGER | read-only | Total time, in seconds, for data traffic |
| INT totalDataUsage | 1.3.6.1.4.1.2858.8.2.1.16 | INTEGER | read-only | Time, in seconds, used for data transfer/modem calls on the port |
| INT totalEgressCount | 1.3.6.1.4.1.2858.10.6 | INTEGER | read-only | Total number of egress events |
| INT totalEgressTime | 1.3.6.1.4.1.2858.10.5 | INTEGER | read-only | Total time, in seconds, for egress traffic |
| INT totalEventCount | 1.3.6.1.4.1.2858.10.2 | INTEGER | read-only | Total number of events in gateway |
| INT totalFaxCount | 1.3.6.1.4.1.2858.10.8 | INTEGER | read-only | Total number of fax events |
| INT totalFaxTime | 1.3.6.1.4.1.2858.10.7 | INTEGER | read-only | Total time, in seconds, for fax traffic |
| INT totalFaxUsage | 1.3.6.1.4.1.2858.8.2.1.14 | INTEGER | read-only | Time, in seconds, used for fax calls on the port |
| INT totalIngressCount | 1.3.6.1.4.1.2858.10.4 | INTEGER | read-only | Total number of ingress events |
| INT totalIngressTime | 1.3.6.1.4.1.2858.10.3 | INTEGER | read-only | Total time, in seconds, for ingress traffic |
| INT totalInterval | 1.3.6.1.4.1.2858.10.1 | INTEGER | read-only | Time, in seconds, since any member of the Traffic Stats group was last read |
| INT totalOutSvcCount | 1.3.6.1.4.1.2858.10.10 | INTEGER | read-only | Total number of egress events :: Reserved; Not Implemented |
| INT totalOutSvcTime | 1.3.6.1.4.1.2858.10.9 | INTEGER | read-only | Total time, in seconds, that the gateway has been out of service :: Reserved; Not Implemented |
| INT totalVoiceCount | 1.3.6.1.4.1.2858.10.14 | INTEGER | read-only | Total number of voice events |
| INT totalVoiceTime | 1.3.6.1.4.1.2858.10.13 | INTEGER | read-only | Total time, in seconds, for voice traffic |
| INT totalVoiceUsage | 1.3.6.1.4.1.2858.8.2.1.12 | INTEGER | read-only | Time, in seconds, used for voice calls on the port |
| tpConfig | 1.3.6.1.4.1.2858.100.3.2 | |||
| STR tpConfigCommand | 1.3.6.1.4.1.2858.100.3.2.4 | DisplayString | read-write | Use this variable to issue commands to the Clarent ThroughPacket server |
| INT tpEnableStats | 1.3.6.1.4.1.2858.100.3.3.1 | INTEGER | read-write | Enables statistics messages from Clarent ThroughPacket to the Command Center. Specify a value of 1 to enable statistics. The default value is 0 (zero), which disables statistics. |
| NTF tpIsDown | 1.3.6.1.4.1.2858.4.0.9936 | Clarent ThroughPacket server is down | ||
| INT tpOperState | 1.3.6.1.4.1.2858.100.3.1.3 | INTEGER | read-only | State of the TP, enabled means running, disabled means not running |
| NTF tpRestarted | 1.3.6.1.4.1.2858.4.0.9938 | Clarent ThroughPacket server restarted successfully | ||
| INT tpRunTimeCtrl | 1.3.6.1.4.1.2858.100.3.2.5 | INTEGER | read-write | Start or stop the Clarent ThroughPacket server |
| tpStatisticsManagement | 1.3.6.1.4.1.2858.100.3.3 | |||
| INT tpStatsInterval | 1.3.6.1.4.1.2858.100.3.3.2 | INTEGER | read-write | Interval, in minutes, between statistics messages from Clarent ThroughPacket to the Command Center |
| INT tpStatus | 1.3.6.1.4.1.2858.100.3.1.1 | INTEGER | read-only | Current status of the Clarent ThroughPacket server |
| INT tpstatusCode | 1.3.6.1.4.1.2858.100.3.1.2 | INTEGER | read-only | If tpstatus is inError, interrogate this variable for more information. |
| STR trafficStatus | 1.3.6.1.4.1.2858.1.6 | DisplayString | read-only | Traffic information: idle, ingress, egress, fax, and out of service time |
| trap_Parameters | 1.3.6.1.4.1.2858.48 | |||
| STR trapAppName | 1.3.6.1.4.1.2858.48.6 | DisplayString | read-only | Name of the Clarent Application issuing the Trap |
| INT trapClass | 1.3.6.1.4.1.2858.48.2 | INTEGER | read-only | Trap class |
| INT trapCount | 1.3.6.1.4.1.2858.48.5 | INTEGER | read-only | Number of specific traps sent from the agent |
| INT trapNumber | 1.3.6.1.4.1.2858.48.3 | INTEGER | read-only | Class-specific trap number |
| INT trapParm1 | 1.3.6.1.4.1.2858.6.2 | INTEGER | read-write | Allows traps to have integer parameters |
| INT trapParm2 | 1.3.6.1.4.1.2858.6.3 | INTEGER | read-write | Allows traps to have integer parameters |
| INT trapParm3 | 1.3.6.1.4.1.2858.6.4 | INTEGER | read-write | Allows traps to have integer parameters |
| STR trapParm4 | 1.3.6.1.4.1.2858.6.5 | DisplayString | read-write | Allows traps to have string parameters |
| INT trapSeverity | 1.3.6.1.4.1.2858.48.1 | INTEGER | read-only | Trap severity |
| STR trapText | 1.3.6.1.4.1.2858.48.4 | DisplayString | read-only | Text on a per trap Basis |
| STR unpackCommand | 1.3.6.1.4.1.2858.100.1.4 | DisplayString | read-write | Initiate an UNPACK command. In the SET command, specify the package name. |
| INT unpackError | 1.3.6.1.4.1.2858.100.1.2.1.8 | INTEGER | read-only | Package unpack error |
| STR unpackMessage | 1.3.6.1.4.1.2858.100.1.2.1.7 | DisplayString | read-only | Package unpack status message |
| INT unpackStatus | 1.3.6.1.4.1.2858.100.1.2.1.6 | INTEGER | read-only | Package unpack status |
| NTF validateEGErr | 1.3.6.1.4.1.2858.4.0.9931 | Clarent Gateway validate egress error | ||
| NTF validCCTmpLicense | 1.3.6.1.4.1.2858.4.0.9920 | Valid temporary Command Center license | ||
| versionEntry | 1.3.6.1.4.1.2858.100.5.1.1 | not-accessible | Version Table Entry containing version component information | |
| versionManagement | 1.3.6.1.4.1.2858.100.5 | |||
| STR versionString | 1.3.6.1.4.1.2858.100.5.1.1.6 | DisplayString | read-only | Version in String Format |
| versionTable | 1.3.6.1.4.1.2858.100.5.1 | not-accessible | A list of Version entries | |
| INT voicecount | 1.3.6.1.4.1.2858.8.2.1.13 | INTEGER | read-only | Total number of voice calls on the port |
| INT xmitCount | 1.3.6.1.4.1.2858.8.2.1.5 | INTEGER | read-only |
RFC description
Clarent gateway and gatekeeper management for VoIP call control and statistics.
Start monitoring Clarent VoIP gateway (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.