CDD-564

All MIBs › CDD-564

Organization: Comtech EF Data Corp.

Last Updated: 2005--1-2-

Category: Satellite, Vendor: Comtech EF Data

Description: Manages Comtech EF Data CDD-564 satellite modem demodulator configuration including symbol rate, FEC, and demodulator status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CDD-564?

CDD-564 is a Comtech EF Data vendor-specific MIB that manages and monitors the CDD-564 satellite demodulator, exposing configuration for demodulator behavior alongside live signal-quality telemetry. Its cdd564RxTable (indexed 1..4 per demodulator) carries cdd564RxFEC (uncoded/turbo), cdd564RxDemodulation (QPSK/8-PSK/16-QAM), cdd564RxSymbolRate, cdd564RxCodeRate, and alarm thresholds like cdd564RxEbNoAlarmPoint, while runtime status objects such as cdd564RxEbNo, cdd564AGCAlarmMask, and cdd564EbNoAlarmMask report actual signal-to-noise and automatic-gain-control conditions. Event history is tracked in a per-demodulator cdd564EventTable (indexed by cdd564EventDemod and cdd564EventIndex) and long-run signal statistics in cdd564StatisticTable (cdd564StatisticAvgEbNo, cdd564StatisticMinEbNo), while cdd564AccessListTable, cdd564RouteTable, and cdd564IGMPTable manage IP-over-satellite networking features. It depends on the ComtechEFData enterprise MIB tree for its OID placement and is deployed on Comtech EF Data CDD-564 satellite modem/demodulator units in VSAT and satellite backhaul links, where technicians can download the CDD-564 MIB to load into their MIB browser for provisioning and signal-quality monitoring.

IPNetwork Monitor allows you to monitor SNMP objects defined in CDD-564. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Comtech EF Data CDD-564 satellite modem/demodulator

Monitoring Examples

An operator polls cdd564RxEbNo against cdd564RxEbNoAlarmPoint for a given cdd564RxTableIndex to check demodulator signal margin, and reviews cdd564StatisticMinEbNo to see the worst Eb/No recorded over the period; an Eb/No value dropping below the configured alarm point combined with entries appearing in cdd564EventTable would indicate a degrading satellite link or antenna pointing issue.

What Can Be Monitored

demodulator Eb/No signal level and alarm threshold
AGC and Eb/No alarm masks
FEC/demodulation mode and symbol rate configuration
per-demodulator event log table
long-term Eb/No statistics (avg/min)
IP routing and IGMP table state

Imported Objects

From ComtechEFData

comtechEFData

MODULE-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT cdd546RxSpectrumInversion	1.3.6.1.4.1.6247.25.1.7.1.1.1.10	INTEGER	read-write	Rx spectrum inversion, where: 0 = Normal 1 = Rx spectrum inverted
cdd564	1.3.6.1.4.1.6247.25			Module for CDD-564 Satellite Demod
cdd5643xDESEncryption	1.3.6.1.4.1.6247.25.1.1.3
STR cdd5643xDESRxKey1	1.3.6.1.4.1.6247.25.1.1.3.1.1.2	DisplayString	read-write	The 3xDES receive decrypt key. The key length is 192 bits (24 bytes or 48 characters).
STR cdd5643xDESRxKey2	1.3.6.1.4.1.6247.25.1.1.3.1.1.3	DisplayString	read-write	The 3xDES receive decrypt key. The key length is 192 bits (24 bytes or 48 characters).
STR cdd5643xDESRxKey3	1.3.6.1.4.1.6247.25.1.1.3.1.1.4	DisplayString	read-write	The 3xDES receive decrypt key. The key length is 192 bits (24 bytes or 48 characters).
STR cdd5643xDESRxKey4	1.3.6.1.4.1.6247.25.1.1.3.1.1.5	DisplayString	read-write	The 3xDES receive decrypt key. The key length is 192 bits (24 bytes or 48 characters).
STR cdd5643xDESRxKey5	1.3.6.1.4.1.6247.25.1.1.3.1.1.6	DisplayString	read-write	The 3xDES receive decrypt key. The key length is 192 bits (24 bytes or 48 characters).
STR cdd5643xDESRxKey6	1.3.6.1.4.1.6247.25.1.1.3.1.1.7	DisplayString	read-write	The 3xDES receive decrypt key. The key length is 192 bits (24 bytes or 48 characters).
STR cdd5643xDESRxKey7	1.3.6.1.4.1.6247.25.1.1.3.1.1.8	DisplayString	read-write	The 3xDES receive decrypt key. The key length is 192 bits (24 bytes or 48 characters).
STR cdd5643xDESRxKey8	1.3.6.1.4.1.6247.25.1.1.3.1.1.9	DisplayString	read-write	The 3xDES receive decrypt key. The key length is 192 bits (24 bytes or 48 characters).
cdd5643xDESRxKeyEntry	1.3.6.1.4.1.6247.25.1.1.3.1.1		not-accessible	The entry (per demod) of the 3xDES receive decrypt key table.
INT cdd5643xDESRxKeyIndex	1.3.6.1.4.1.6247.25.1.1.3.1.1.1	INTEGER	read-only	The index (per demod) of the 3xDES receive decrypt key table.
cdd5643xDESRxKeyTable	1.3.6.1.4.1.6247.25.1.1.3.1		not-accessible	The table (one row per demod) for triple DES (3xDES) receive decrypt keys.
IP cdd564AccessIPAddress	1.3.6.1.4.1.6247.25.1.1.1.1.1.2	IpAddress	read-write	The IP addresses that can access the unit. The value of 0.0.0.0 means not defined.
INT cdd564AccessListEnforcement	1.3.6.1.4.1.6247.25.1.1.1.2	INTEGER	read-write	Enable or disable enforcement of the the access list. Note: Be sure that you have added the SNMP browser's/manager's IP Address to the access list before enabling access list filtering. Otherwise, the SNMP browser/manager will no longer be able to gain access to the unit.
cdd564AccessListEntry	1.3.6.1.4.1.6247.25.1.1.1.1.1		not-accessible	The entry for the access list table.
INT cdd564AccessListIndex	1.3.6.1.4.1.6247.25.1.1.1.1.1.1	INTEGER	read-only	The index for the access list from 1..4.
cdd564AccessLists	1.3.6.1.4.1.6247.25.1.1.1
cdd564AccessListTable	1.3.6.1.4.1.6247.25.1.1.1.1		not-accessible	The table for the access list.
INT cdd564AccessSubnetMaskLength	1.3.6.1.4.1.6247.25.1.1.1.1.1.3	INTEGER	read-write	The subnet mask length of the IP address for the access list. Subnet mask can be from 8..32. The value of 0 means not defined.
cdd564Administration	1.3.6.1.4.1.6247.25.1.1
INT cdd564AGCAlarmMask	1.3.6.1.4.1.6247.25.1.7.2.1.1.2	INTEGER	read-write	Rx AGC alarm mask, where: 0 = Unmasked 1 = Masked
cdd564AlarmMask	1.3.6.1.4.1.6247.25.1.7.2
cdd564AlarmMaskEntry	1.3.6.1.4.1.6247.25.1.7.2.1.1		not-accessible	Description.
INT cdd564AlarmMaskIndex	1.3.6.1.4.1.6247.25.1.7.2.1.1.1	INTEGER	read-only	The index for the Demodulator.
cdd564AlarmMaskTable	1.3.6.1.4.1.6247.25.1.7.2.1		not-accessible	Description.
INT cdd564BootImage	1.3.6.1.4.1.6247.25.1.5.2.1	INTEGER	read-write	Specifies which image will be booted: latest - boots the latest image determined by the most recent build date image 1 - boots image from bulk #1 image 2 - boots image from bulk #2
STR cdd564BootInfo	1.3.6.1.4.1.6247.25.1.5.1.1	DisplayString	read-only	The version and revision information for the boot application.
STR cdd564Bulk1Info	1.3.6.1.4.1.6247.25.1.5.1.2	DisplayString	read-only	The version and revision information for the bulk application in image 1.
STR cdd564Bulk2Info	1.3.6.1.4.1.6247.25.1.5.1.3	DisplayString	read-only	The version and revision information for the bulk application in image 2.
cdd564BulkDatabase	1.3.6.1.4.1.6247.25.1.5.2
STR cdd564CircuitID	1.3.6.1.4.1.6247.25.1.9.6.1.2	DisplayString	read-write	Sets or queries the user-defined Circuit ID string, which is a fixed length of 24 characters. Valid characters include: Space ( ) * + - , . / 0 thru 9 and A thru Z.
cdd564CircuitIDEntry	1.3.6.1.4.1.6247.25.1.9.6.1		not-accessible	The entry for the circuit ID table.
INT cdd564CircuitIDIndex	1.3.6.1.4.1.6247.25.1.9.6.1.1	INTEGER	read-only	The index for the Demodulator.
cdd564CircuitIDTable	1.3.6.1.4.1.6247.25.1.9.6		not-accessible	The table for Circuit IDs (Per Demod).
INT cdd564ClearAllStoredEvents	1.3.6.1.4.1.6247.25.1.8.4.2	INTEGER	read-write	This is a SET command to clear the event log for one of the four demods (1 - 4).
INT cdd564ClearAllStoredStatistics	1.3.6.1.4.1.6247.25.1.8.5.3	INTEGER	read-write	This is a SET command to clear the statistics log for one of the four demods (1 - 4).
cdd564Compliance	1.3.6.1.4.1.6247.25.3.2.1			CDD-564 Compliance.
cdd564Compliances	1.3.6.1.4.1.6247.25.3.2
cdd564Config	1.3.6.1.4.1.6247.25.1.7
cdd564Conformance	1.3.6.1.4.1.6247.25.3
cdd564DemodulatorInterfaces	1.3.6.1.4.1.6247.25.1.2.2
C32 cdd564DroppedPacketsBadBufferLength	1.3.6.1.4.1.6247.25.1.6.1.5.3	Counter32	read-only	The total number of packets dropped by the router because of a bad packet buffer length.
C32 cdd564DroppedPacketsBadIPHeader	1.3.6.1.4.1.6247.25.1.6.1.5.2	Counter32	read-only	The total number of packets dropped by the router because of a bad checksum in the IP header.
C32 cdd564DroppedPacketsBadIPVersion	1.3.6.1.4.1.6247.25.1.6.1.5.4	Counter32	read-only	The total number of packets dropped by the router because of the packet is not IPv4. Note: IPv6 packets are not support by the router.
C32 cdd564DroppedPacketsFiltered	1.3.6.1.4.1.6247.25.1.6.1.5.10	Counter32	read-only	The total number of packets dropped by the router for the following reasons: 1. Boot 2. Flow Descriptor 3. Unknown Reason Code 4. Flow Correlator 5. Management Path 6. Ping 7. Access Control 8. Vipersat Multicommand 9. Vipersat Unicommand 10. Codeload 11. Multicast 12. Bad Packet 13. Route 14. Bad Header Len 15. Bad Data Ptr 16. MAC Split Err 17. L3Type Err 18. Local Destination 19. ICMP Filter 20. Port Err 21. Per port route rule
C32 cdd564DroppedPacketsFilteredMulticast	1.3.6.1.4.1.6247.25.1.6.1.5.8	Counter32	read-only	The total number of multicast packets dropped by the router because the multicast address is not being forwarded.
C32 cdd564DroppedPacketsMulticastDisableGroup	1.3.6.1.4.1.6247.25.1.6.1.5.9	Counter32	read-only	The total number of multicast packets dropped by the router because the multicast group is not being forwarded.
C32 cdd564DroppedPacketsNoARPEntry	1.3.6.1.4.1.6247.25.1.6.1.5.7	Counter32	read-only	The total number of packets dropped by the router because the ARP table did not have an ARP entry for the packet's next hop.
C32 cdd564DroppedPacketsNoRoute	1.3.6.1.4.1.6247.25.1.6.1.5.6	Counter32	read-only	The total number of packets dropped by the router because the packet did not match any route in the route table and could not be forwarded.
C32 cdd564DroppedPacketsRouterQueueFull	1.3.6.1.4.1.6247.25.1.6.1.5.11	Counter32	read-only	The total number of packets dropped by the router because the router queue is full.
C32 cdd564DroppedPacketsTTLExpired	1.3.6.1.4.1.6247.25.1.6.1.5.5	Counter32	read-only	The total number of packets dropped by the router because the TTL (time to live) in the IP header had expired (i.e. reached zero).
INT cdd564EbNoAlarmMask	1.3.6.1.4.1.6247.25.1.7.2.1.1.3	INTEGER	read-write	Eb/No alarm mask, where: 0 = Unmasked 1 = Masked
INT cdd564EthernetClearCounters	1.3.6.1.4.1.6247.25.1.6.2.3	INTEGER	read-write	Reset all ethernet transmit & receive counters.
cdd564EthernetInterface	1.3.6.1.4.1.6247.25.1.2.1
cdd564EthernetRxStats	1.3.6.1.4.1.6247.25.1.6.2.2
INT cdd564EthernetSpeed	1.3.6.1.4.1.6247.25.1.2.1.2	INTEGER	read-write	The speed of the Ethernet interface.
cdd564EthernetStatistics	1.3.6.1.4.1.6247.25.1.6.2
cdd564EthernetTxStats	1.3.6.1.4.1.6247.25.1.6.2.1
C32 cdd564EtherRxAllignmentErrors	1.3.6.1.4.1.6247.25.1.6.2.2.3	Counter32	read-only	The number of frames that are both misaligned [in other words, CRS de-asserts on a non-octet boundary] and contain a CRC error.
C32 cdd564EtherRxCollisionDetectErrors	1.3.6.1.4.1.6247.25.1.6.2.2.6	Counter32	read-only	The number of frames that encountered collision during reception. This is always zero.
C32 cdd564EtherRxCRCErrorFrames	1.3.6.1.4.1.6247.25.1.6.2.2.2	Counter32	read-only	The number of aligned frames discarded due to CRC Errors.
C32 cdd564EtherRxFIFOOverrunErrors	1.3.6.1.4.1.6247.25.1.6.2.2.5	Counter32	read-only	The number of frames known to be lost because the internal receive FIFO overflowed [also known as receive overrun]. This can occur if the device is unable to get necessary PCI bandwidth. If the overflow condition persists for more than one frame, the frames that follow the first can also be lost. A frame that was counted as an overrun will not be counted in other error counters like (short frames, misaligned, CRC error).
C32 cdd564EtherRxFlowControlPauseFrames	1.3.6.1.4.1.6247.25.1.6.2.2.8	Counter32	read-only	The number of flow control frames received by the device. This count includes both XOFF and XON frames received.
C32 cdd564EtherRxGoodFrames	1.3.6.1.4.1.6247.25.1.6.2.2.1	Counter32	read-only	The number of frames properly received from the link. It is updated only after actual reception from the link is completed and all data bytes are stored in memory.
C32 cdd564EtherRxResourceErrors	1.3.6.1.4.1.6247.25.1.6.2.2.4	Counter32	read-only	The number of good frames discarded due to unavailable resources.
C32 cdd564EtherRxShortFrames	1.3.6.1.4.1.6247.25.1.6.2.2.7	Counter32	read-only	The number of received frames that are shorter than the minimum frame length.
C32 cdd564EtherTxDeferred	1.3.6.1.4.1.6247.25.1.6.2.1.6	Counter32	read-only	The number of frames deferred before transmission due to activity on the link.
C32 cdd564EtherTxDMAUnderrun	1.3.6.1.4.1.6247.25.1.6.2.1.4	Counter32	read-only	The number of frames that were either NOT transmitted or retransmitted due to Transmit DMA underrun. Underruns occur due to lack of PCI bandwidth resulting in the internal transmit FIFO running dry during the transmission of a frame.
C32 cdd564EtherTxFlowControlPauseFrames	1.3.6.1.4.1.6247.25.1.6.2.1.10	Counter32	read-only	The number of flow control frames transmitted by the device. This count includes both the XOFF and XON frames transmitted by the device.
C32 cdd564EtherTxGoodFrames	1.3.6.1.4.1.6247.25.1.6.2.1.1	Counter32	read-only	The number of transmitted good frames from the Ethernet interface.
C32 cdd564EtherTxLateCollisions	1.3.6.1.4.1.6247.25.1.6.2.1.3	Counter32	read-only	The number of frames that were NOT transmitted because they encountered collision outside the normal collision window.
C32 cdd564EtherTxLostCarrierSense	1.3.6.1.4.1.6247.25.1.6.2.1.5	Counter32	read-only	The number of frames transmitted by the device despite the fact that it detected the de-assertion of Transmit Lost Carrier Sense (CRS) during the transmission.
C32 cdd564EtherTxMaxCollisions	1.3.6.1.4.1.6247.25.1.6.2.1.2	Counter32	read-only	The number of frames that were NOT transmitted because they encountered the maximum configured collisions. This counter should only increment when network is heavily saturated with traffic.
C32 cdd564EtherTxMultipleCollisions	1.3.6.1.4.1.6247.25.1.6.2.1.8	Counter32	read-only	The number of transmitted frames that encountered more than 1 collision.
C32 cdd564EtherTxSingleCollisions	1.3.6.1.4.1.6247.25.1.6.2.1.7	Counter32	read-only	The number of transmitted frames that encountered only 1 collision.
C32 cdd564EtherTxTotalCollisions	1.3.6.1.4.1.6247.25.1.6.2.1.9	Counter32	read-only	The total number of collisions that were encountered while attempting to transmit. This count includes late collisions and collisions from frames that encountered maximum collisions.
INT cdd564EventDemod	1.3.6.1.4.1.6247.25.1.8.4.1.1.1	INTEGER	read-only	The demodulator index for which event log is being returned.
STR cdd564EventDescription	1.3.6.1.4.1.6247.25.1.8.4.1.1.3	DisplayString	read-only	Event description string with the following format seprated by commas: 1. Date in form dd/mm/yy, where: dd = day of the month (01 to 31) mm = month (01 to 12) yy = year (00 to 99) 2. Time in form hh:mm:ss, where: hh = hours (00 to 23) mm = minutes (00 to 59) ss = seconds (00 to 59) 3. Event Type in form xxxxx, where xxxxx is Clear = fault cleared Fault = fault occurred Info = information 4. Texual Description of Event
INT cdd564EventIndex	1.3.6.1.4.1.6247.25.1.8.4.1.1.2	INTEGER	read-only	The index for a demod's stored events table.
INT cdd564FeatureIndex	1.3.6.1.4.1.6247.25.1.1.2.5.1.1	INTEGER	read-only	The index for the FAST Feature (per demod) table.
cdd564Features	1.3.6.1.4.1.6247.25.1.1.2
cdd564FeaturesEntry	1.3.6.1.4.1.6247.25.1.1.2.5.1		not-accessible	The entry for the FAST Feature (per demod) table.
cdd564FeaturesTable	1.3.6.1.4.1.6247.25.1.1.2.5		not-accessible	The table (per demodulator) of FAST Features.
INT cdd564ForwardMulticasts	1.3.6.1.4.1.6247.25.1.1.2.4	INTEGER	read-write	Enable or disable forwarding all multicasts received from the Satellite interface to the Ethernet interface.
STR cdd564FPGARx1Info	1.3.6.1.4.1.6247.25.1.5.1.4	DisplayString	read-only	The version and revision information for the Rx FPGA in image 1.
STR cdd564FPGARx2Info	1.3.6.1.4.1.6247.25.1.5.1.5	DisplayString	read-only	The version and revision information for the Rx FPGA in image 2.
cdd564Groups	1.3.6.1.4.1.6247.25.3.1
INT cdd564HDLCAddress1	1.3.6.1.4.1.6247.25.1.2.2.3.1.3	INTEGER	read-write	The HDLC address #1 for the satellite interface. The valid values are: 1. Small network, 1 to 254 (0x1 - 0xFE). 2. Large network, 1 to 32766 (0x1 - 0x0x7FFE). 3. Point to point, not used. 4. EasyConnect, not used. HDLC address can not have 0x00 or 0xFF in least significant byte, i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses. Deletion: To delete the HDLC address, set it to zero.
INT cdd564HDLCAddress2	1.3.6.1.4.1.6247.25.1.2.2.3.1.4	INTEGER	read-write	The HDLC address #2 for the satellite interface. The valid values are: 1. Small network, 1 to 254 (0x1 - 0xFE). 2. Large network, 1 to 32766 (0x1 - 0x0x7FFE). 3. Point to point, not used. 4. EasyConnect, not used. HDLC address can not have 0x00 or 0xFF in least significant byte, i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses. Deletion: To delete the HDLC address, set it to zero.
INT cdd564HDLCAddress3	1.3.6.1.4.1.6247.25.1.2.2.3.1.5	INTEGER	read-write	The HDLC address #3 for the satellite interface. The valid values are: 1. Small network, 1 to 254 (0x1 - 0xFE). 2. Large network, 1 to 32766 (0x1 - 0x0x7FFE). 3. Point to point, not used. 4. EasyConnect, not used. HDLC address can not have 0x00 or 0xFF in least significant byte, i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses. Deletion: To delete the HDLC address, set it to zero.
INT cdd564HDLCAddress4	1.3.6.1.4.1.6247.25.1.2.2.3.1.6	INTEGER	read-write	The HDLC address #4 for the satellite interface. The valid values are: 1. Small network, 1 to 254 (0x1 - 0xFE). 2. Large network, 1 to 32766 (0x1 - 0x0x7FFE). 3. Point to point, not used. 4. EasyConnect, not used. HDLC address can not have 0x00 or 0xFF in least significant byte, i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses. Deletion: To delete the HDLC address, set it to zero.
cdd564HDLCAddressEntry	1.3.6.1.4.1.6247.25.1.2.2.3.1		not-accessible	The entry of the HDLC Address table.
INT cdd564HDLCAddressIndex	1.3.6.1.4.1.6247.25.1.2.2.3.1.1	INTEGER	read-only	The Demod number corresponding to 1 of 4 demodulators.
INT cdd564HDLCAddressMode	1.3.6.1.4.1.6247.25.1.2.2.2	INTEGER	read-only	The size of HDLC address used for sending packets over satellite interface can range from 0 - 2 bytes. The satellite interface will operate in one of the following modes: 1.Small Network mode - The packet uses a 1 byte HDLC address. The valid values are from 1 to 254 (0x1 - 0xFE). 2.Large Network mode - The packet uses a 2 byte HDLC address. The valid values are from 1 to 32766 (0x1 - 0x7FFE). 3. Point To Point mode - The packet does not use a HDLC address. An HDLC address cannot have 0x00 or 0xFF in least Significant Byte. i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses.
cdd564HDLCAddressTable	1.3.6.1.4.1.6247.25.1.2.2.3		not-accessible	The table for the Demodulator HDLC Addresses.
INT cdd564HeaderCompression	1.3.6.1.4.1.6247.25.1.1.2.5.1.2	INTEGER	read-write	Availability of header compression is based on FAST features Note: To use header compression, it must be FAST available and enabled on both the transmit and receive sides.
INT cdd564IGMP	1.3.6.1.4.1.6247.25.1.1.2.3	INTEGER	read-write	Enable or disable the Internet Group Management Protocol (IGMP).
INT cdd564IGMPClientState	1.3.6.1.4.1.6247.25.1.4.1.3.1.3	INTEGER	read-only	The state for the multicast group.
cdd564IGMPConfig	1.3.6.1.4.1.6247.25.1.4.1
cdd564IGMPEntry	1.3.6.1.4.1.6247.25.1.4.1.3.1		not-accessible	The entry for the IGMP group table.
IP cdd564IGMPGroupIPAddress	1.3.6.1.4.1.6247.25.1.4.1.3.1.5	IpAddress	read-only	The multicast group address.
INT cdd564IGMPIndex	1.3.6.1.4.1.6247.25.1.4.1.3.1.1	INTEGER	read-only	The index for the IGMP group table.
INT cdd564IGMPMaxMissBeforeLeavingGroup	1.3.6.1.4.1.6247.25.1.4.1.1.3	INTEGER	read-write	The maximum number of missed responses before leaving the IGMP group.
INT cdd564IGMPMaxResponseTime	1.3.6.1.4.1.6247.25.1.4.1.1.2	INTEGER	read-write	The IGMP maximum response time, in seconds.
C32 cdd564IGMPPacketsReceived	1.3.6.1.4.1.6247.25.1.6.1.4.1	Counter32	read-only	The total number of IGMP packets received by the endstation.
INT cdd564IGMPQueryPeriod	1.3.6.1.4.1.6247.25.1.4.1.1.1	INTEGER	read-write	The IGMP query period, in seconds.
cdd564IGMPServer	1.3.6.1.4.1.6247.25.1.4.1.1
INT cdd564IGMPSrc	1.3.6.1.4.1.6247.25.1.4.1.3.1.4	INTEGER	read-only	The interface from which the multicast group was received.
cdd564IGMPTable	1.3.6.1.4.1.6247.25.1.4.1.3		not-accessible	The table for IGMP groups.
INT cdd564IGMPTTL	1.3.6.1.4.1.6247.25.1.4.1.3.1.2	INTEGER	read-only	The TTL for the multicast group.
cdd564Interfaces	1.3.6.1.4.1.6247.25.1.2
INT cdd564InternalReferenceAdjust	1.3.6.1.4.1.6247.25.1.7.3.2	INTEGER	read-write	Internal Reference Adjust, from -999 to +999. Units = KHz
IP cdd564IPAddress	1.3.6.1.4.1.6247.25.1.2.1.3	IpAddress	read-write	The IP address assigned to the Ethernet interface.
C32 cdd564IPOptionPacketsReceived	1.3.6.1.4.1.6247.25.1.6.1.4.2	Counter32	read-only	The total number of packets received with IP Options in the IP header.
INT cdd564IPRoutingClearCounters	1.3.6.1.4.1.6247.25.1.6.1.6	INTEGER	read-write	This is a SET command to clear the IP routing counters.
cdd564IPRoutingDropped	1.3.6.1.4.1.6247.25.1.6.1.5
cdd564IPRoutingEndstation	1.3.6.1.4.1.6247.25.1.6.1.3
cdd564IPRoutingEthernet	1.3.6.1.4.1.6247.25.1.6.1.1
cdd564IPRoutingMisc	1.3.6.1.4.1.6247.25.1.6.1.4
cdd564IPRoutingSatellite	1.3.6.1.4.1.6247.25.1.6.1.2
cdd564IPRoutingStatistics	1.3.6.1.4.1.6247.25.1.6.1
cdd564LNB	1.3.6.1.4.1.6247.25.1.7.4
INT cdd564LNB10MHzReference	1.3.6.1.4.1.6247.25.1.7.4.1.1.3	INTEGER	read-write	LNB 10MHz frequency reference, where: 0 = Disable LNB 10MHz reference 1 = Enable LNB 10MHz reference
INT cdd564LNBAlarm	1.3.6.1.4.1.6247.25.1.8.3.1.1.2	INTEGER	read-only	LNB alarms Value Description of status parameter 0 No LNB faults 7 LNB current 9 LNB voltage
INT cdd564LNBAlarmMask	1.3.6.1.4.1.6247.25.1.7.2.1.1.5	INTEGER	read-write	LNB alarm mask, where: 0 = Unmasked 1 = Masked
NTF cdd564LNBAlarmNotification	1.3.6.1.4.1.6247.25.2.0.3			Trap for LNB alarms.
INT cdd564LNBCurrent	1.3.6.1.4.1.6247.25.1.8.3.1.1.3	INTEGER	read-only	Indicates the value of the LNB current, between 0 and 999 mA.
INT cdd564LNBDCPower	1.3.6.1.4.1.6247.25.1.7.4.1.1.2	INTEGER	read-write	LNB power control, where: 0 = Off 1 = On, 13V LNB voltage 2 = On, 18V LNB voltage 3 = On, 24V LNB voltage
cdd564LNBEntry	1.3.6.1.4.1.6247.25.1.7.4.1.1		not-accessible	The entry for the LNBs table.
INT cdd564LNBHighCurrentLimit	1.3.6.1.4.1.6247.25.1.7.4.1.1.5	INTEGER	read-write	LNB upper alarm limit for current, between 50 and 600 mA.
INT cdd564LNBIndex	1.3.6.1.4.1.6247.25.1.7.4.1.1.1	INTEGER	read-only	The index for the LNB..
INT cdd564LNBLOFrequency	1.3.6.1.4.1.6247.25.1.7.4.1.1.6	INTEGER	read-write	LNB receieve LO frequency, in the range of 3000 to 65000 MHz. Setting a 0 disables the feature. Terminal Frequency = LNB_LO +/- Rx_Frequency (depending on High/Low Mix)
INT cdd564LNBLOMix	1.3.6.1.4.1.6247.25.1.7.4.1.1.7	INTEGER	read-write	LO frequency mix, where: 0 = Low-side mix 1 = High-side mix
cdd564LNBMonitor	1.3.6.1.4.1.6247.25.1.8.3
cdd564LNBMonitorEntry	1.3.6.1.4.1.6247.25.1.8.3.1.1		not-accessible	The entry for the LNBs monitoring table.
INT cdd564LNBMonitorIndex	1.3.6.1.4.1.6247.25.1.8.3.1.1.1	INTEGER	read-only	The index for the LNBs monitoring table.
cdd564LNBMonitorTable	1.3.6.1.4.1.6247.25.1.8.3.1		not-accessible	The table for monitoring LNBs.
cdd564LNBTable	1.3.6.1.4.1.6247.25.1.7.4.1		not-accessible	The table for LNBs.
INT cdd564LNBTerminalRxFreq	1.3.6.1.4.1.6247.25.1.8.3.1.1.5	INTEGER	read-only	Terminal Rx frequency = LNB LO +/- Rx_Frequency (depending on LO mix) Units = 100 Hz Resolution = 100 Hz Returns 0 if LNB_LO is zero.
INT cdd564LNBVoltage	1.3.6.1.4.1.6247.25.1.8.3.1.1.4	INTEGER	read-only	Indicates the value of the LNB voltage, between 0 and 30 volts. Units = 0.1 volts If not available, response is 0.
STR cdd564MACAddress	1.3.6.1.4.1.6247.25.1.2.1.1	DisplayString	read-only	The MAC address assigned to the Ethernet interface.
cdd564Maint	1.3.6.1.4.1.6247.25.1.5
INT cdd564ModelNumber	1.3.6.1.4.1.6247.25.1.8.1.3	INTEGER	read-only	Unit's model number.
cdd564Monitor	1.3.6.1.4.1.6247.25.1.8
cdd564Notifications	1.3.6.1.4.1.6247.25.2
cdd564NotificationsGroup	1.3.6.1.4.1.6247.25.3.1.2			CDD-564 Trap Group.
cdd564NotificationsPrefix	1.3.6.1.4.1.6247.25.2.0
cdd564Objects	1.3.6.1.4.1.6247.25.1
cdd564ObjectsGroup	1.3.6.1.4.1.6247.25.3.1.1			CDD-564 Objects Group.
cdd564ParamDatabase	1.3.6.1.4.1.6247.25.1.5.3
INT cdd564ParamImage	1.3.6.1.4.1.6247.25.1.5.3.1	INTEGER	read-write	Specifies if configuration should be read from: paramFile - parameter file stored in flash factoryDefaults - the factory defaults
INT cdd564PingReply	1.3.6.1.4.1.6247.25.1.1.2.1	INTEGER	read-write	Enable or disable ping reply from unit.
cdd564Protocols	1.3.6.1.4.1.6247.25.1.4
INT cdd564Reboot	1.3.6.1.4.1.6247.25.1.5.4.1	INTEGER	read-write	The is a SET command that will reboot the unit. * Important * The command will reboot the unit without saving the configuration to the parameter file in flash.
cdd564RebootUnit	1.3.6.1.4.1.6247.25.1.5.4
cdd564Reference	1.3.6.1.4.1.6247.25.1.7.3
INT cdd564ReferenceFrequency	1.3.6.1.4.1.6247.25.1.7.3.1	INTEGER	read-write	External reference frequency, where: 0 = Internal 10 MHz
INT cdd564ReloadParamFromFlash	1.3.6.1.4.1.6247.25.1.5.3.3	INTEGER	read-write	This is a SET command to reload the configuration from the parameter file in flash.
INT cdd564RestoreFactoryDefaults	1.3.6.1.4.1.6247.25.1.5.3.4	INTEGER	read-write	This is a SET command that restore the configuration to the factory defaults. * Imporant * Setting this command ERASES the parameter file in flash.
IP cdd564RouteDestAddress	1.3.6.1.4.1.6247.25.1.3.1.1.3	IpAddress	read-write	The destination IP address for the route.
INT cdd564RouteDestMaskLen	1.3.6.1.4.1.6247.25.1.3.1.1.4	INTEGER	read-write	The subnet mask lenght for the destination IP address.
cdd564RouteEntry	1.3.6.1.4.1.6247.25.1.3.1.1		not-accessible	The entry for the the route table.
INT cdd564RouteIndex	1.3.6.1.4.1.6247.25.1.3.1.1.1	INTEGER	read-write	The index for the route table.
INT cdd564RouteInterface	1.3.6.1.4.1.6247.25.1.3.1.1.7	INTEGER	read-write	Routes are destined to the Ethernet interface.
INT cdd564RouteMulticast	1.3.6.1.4.1.6247.25.1.3.1.1.6	INTEGER	read-write	If the route is a multicast, packets can be: 1. forwarded 2. filtered If the route is unicast, the field is not applicable.
STR cdd564RouteName	1.3.6.1.4.1.6247.25.1.3.1.1.2	DisplayString	read-write	The name of the route. All routes must be named.
IP cdd564RouteNextHopAddress	1.3.6.1.4.1.6247.25.1.3.1.1.5	IpAddress	read-write	The next hop IP address for the route.
INT cdd564RouteRowStatus	1.3.6.1.4.1.6247.25.1.3.1.1.8	INTEGER	read-write	This value is used for status of route: active(1) - The route is active. These values are used to create or delete route: createAndGo(4) - The route is to be created. destroy(6) - The route to be deleted.
cdd564Routes	1.3.6.1.4.1.6247.25.1.3
cdd564RouteTable	1.3.6.1.4.1.6247.25.1.3.1		not-accessible	The route table used in Router mode.
STR cdd564RTCDate	1.3.6.1.4.1.6247.25.1.9.4	DisplayString	read-write	A date in the form dd/mm/yy, where dd = day of the month (01 to 31) mm = month (01 to 12) yy = year (00 to 99)
STR cdd564RTCTime	1.3.6.1.4.1.6247.25.1.9.5	DisplayString	read-write	A time in the form hh:mm:ss, indicating the time from midnight, where: hh = hours (00 to 23) mm = minutes (00 to 59) ss = seconds (00 to 59)
cdd564Rx	1.3.6.1.4.1.6247.25.1.7.1
C32 cdd564RxAbortOctetErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.7	Counter32	read-only	The count of aborted frames and octet error frames. Aborted frame: A frame is aborted when the frame is not complete and is terminated prematurely with the Abort signal, which is 8 consecutive '1's. Octet error: A frames that was not on a byte boudary or on a multiple of 8-bit boundary.
INT cdd564RxAcquisitionSweepWidth	1.3.6.1.4.1.6247.25.1.7.1.1.1.7	INTEGER	read-write	Rx +/- acquisition sweep range of demodulator, in KHz, ranging from: +/- 1 to +/- 32 KHz (rates = 625 ksym/second)
INT cdd564RxAlarm	1.3.6.1.4.1.6247.25.1.8.2.1.1.2	INTEGER	read-only	Modem RX Traffic Faults Value Description of status parameter 0 Rx Traffic OK 1 Demodulator unlocked 3 AGC Alarm - signal out of range 10 Buffer underflow 11 Buffer overflow 13 Eb/No alarm 15 AIS detected on incoming data
NTF cdd564RxAlarmNotification	1.3.6.1.4.1.6247.25.2.0.2			Trap for Rx alarms.
C32 cdd564RxBadHDLCAddressErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.5	Counter32	read-only	The count of received frames that did not match any of the Rx HDLC addresses.
INT cdd564RxBufferSize	1.3.6.1.4.1.6247.25.1.7.1.1.1.9	INTEGER	read-write	Rx buffer size, where: 0 = Buffer disabled (Clock mode = Rx satellite)
INT cdd564RxCodeRate	1.3.6.1.4.1.6247.25.1.7.1.1.1.4	INTEGER	read-write	Rx code rate, where 4 = Rate 3/4 5 = Rate 7/8 6 = Rate 0.95 7 = Rate 1/1 (Uncoded)
C32 cdd564RxCRCErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.14	Counter32	read-only	The number of frames with a CRC error detected by the Rx FPGA.
INT cdd564RxDataInversion	1.3.6.1.4.1.6247.25.1.7.1.1.1.11	INTEGER	read-write	Invert receive data, where: 0 = Normal 1 = Inverted
INT cdd564RxDataRate	1.3.6.1.4.1.6247.25.1.7.1.1.1.5	INTEGER	read-write	Rx data rate in bps (Varies based on chart below.) Units = bps Resolution = 1 bps FEC Type Modulation Code Rate Data Rate High Rate -------- ----------- ---------- --------------------- --------- Turbo QPSK Rate 3/4 16.0 Kbps to 4.5 Mbps N/A Turbo QPSK Rate 7/8 16.0 Kbps to 5.0 Mbps 5.25 Mbps Turbo QPSK Rate 0.95 16.0 Kbps to 5.0 Mbps 5.667 Mbps Turbo 8-PSK Rate 3/4 16.0 Kbps to 5.0 Mbps 6.75 Mbps Turbo 8-PSK Rate 7/8 16.0 Kbps to 5.0 Mbps 7.875 Mbps Turbo 8-PSK Rate 0.95 16.0 Kbps to 5.0 Mbps 8.5 Mbps Turbo 16-QAM Rate 3/4 16.0 Kbps to 5.0 Mbps 9.0 Mbps Turbo 16-QAM Rate 7/8 16.8 Kbps to 5.0 Mbps 9.98 Mbps
INT cdd564RxDemodulation	1.3.6.1.4.1.6247.25.1.7.1.1.1.3	INTEGER	read-write	Rx demodulation type, where: 1 = QPSK 3 = 8-PSK 4 = 16-QAM
INT cdd564RxDescrambling	1.3.6.1.4.1.6247.25.1.7.1.1.1.8	INTEGER	read-write	Rx descrambler state, where: 0 = Off 1 = On (default descrambler type) 2 = On - IESS-315 (Turbo only)
INT cdd564RxEbNo	1.3.6.1.4.1.6247.25.1.8.2.1.1.3	INTEGER	read-only	Unit returns the value of Eb/No, between 0 and 16 db. Units = 0.1 dB Resolution 0.1 dB Returns 999 if demod is unlocked. For values greater than 16 dB, the reply will be 160.
INT cdd564RxEbNoAlarmPoint	1.3.6.1.4.1.6247.25.1.7.1.1.1.12	INTEGER	read-write	Rx Eb/No alarm point in 0.1 dB, with a range between 0.1 dB and 16 dB. Units = 0.1 dB Resolution = 0.1 dB
cdd564RxEntry	1.3.6.1.4.1.6247.25.1.7.1.1.1		not-accessible	The entry for the Demodulator table.
INT cdd564RxFEC	1.3.6.1.4.1.6247.25.1.7.1.1.1.2	INTEGER	read-write	Rx FEC type where: 0 = Uncoded 6 = Turbo
INT cdd564RxFreqOffset	1.3.6.1.4.1.6247.25.1.8.2.1.1.5	INTEGER	read-only	Unit returns the value of the measured frequency offset of the carrier being demodulated in Hz. Units = Hz. Resolution 100 Hz. Range = -200,000 Hz to 0 Hz and 0 Hz to 200,000 Hz.
INT cdd564RxFrequency	1.3.6.1.4.1.6247.25.1.7.1.1.1.6	INTEGER	read-write	Rx frequency for L-Band and IF-Band modes. L-Band is 950 MHz to 1950 MHz. IF-Band is 50 MHz to 90 MHz and 100 MHz to 180 MHz. Units = Hz. Resolution = 100 Hz.
C32 cdd564RxGoodFrames	1.3.6.1.4.1.6247.25.1.6.3.1.1.2	Counter32	read-only	The total number of good frames received over satellite interface.
C32 cdd564RxHDLCCRCErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.9	Counter32	read-only	The HDLC CRC is the first stage of the CRC check, before 3xDES and paylod Decompression. It indicates any errors due to the satellite link only.
C32 cdd564RxHeaderBytes	1.3.6.1.4.1.6247.25.1.6.3.1.1.3	Counter32	read-only	The count of HDLC header bytes received over the satellite interface. HDLC header = Control + HDLC address + Flow ID + CRC
C32 cdd564RxHeaderDecompressionErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.12	Counter32	read-only	The number of frames with a compressed IP header that encountered an error in decompressing (rebuilding) the full IP header.
C32 cdd564RxInvalidFlowIDErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.10	Counter32	read-only	The number of frames received where the flow ID did not match to a valid flow descriptor.
C32 cdd564RxMemoryAlignmentErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.13	Counter32	read-only	The number of frames which were incorrectly transferred (frame too small) from the Rx FPGA.
cdd564RxMonitor	1.3.6.1.4.1.6247.25.1.8.2
cdd564RxMonitorEntry	1.3.6.1.4.1.6247.25.1.8.2.1.1		not-accessible	The entry for the demoduator monitor table.
INT cdd564RxMonitorIndex	1.3.6.1.4.1.6247.25.1.8.2.1.1.1	INTEGER	read-only	The index for the demodulator monitor table.
cdd564RxMonitorTable	1.3.6.1.4.1.6247.25.1.8.2.1		not-accessible	The table for monitoring demodulators.
C32 cdd564RxOverrunErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.8	Counter32	read-only	The count of received frames that exceeded the maximum frame length of 2K bytes or overflowed the buffer which stores complete HDLC frames.
C32 cdd564RxPayloadBytes	1.3.6.1.4.1.6247.25.1.6.3.1.1.4	Counter32	read-only	The count of payload bytes that were received over satellite interface, excluding any frame overhead.
C32 cdd564RxPktProcCRCErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.6	Counter32	read-only	The Packet Processor CRC check is the second CRC check performed after the HDLC CRC check. It is the checksum calculated after Decryption and Payload Decompression. Failures due to 3xDES and Payload Comp are detected at this level.
INT cdd564RxRecenterBuffer	1.3.6.1.4.1.6247.25.1.7.1.1.1.13	INTEGER	read-write	This is a SET command that recenters the receive Plesiochronous/Doppler buffer.
C32 cdd564RxSARReassembleErrors	1.3.6.1.4.1.6247.25.1.6.3.1.1.11	Counter32	read-only	The number of frames corresponding to a packet which had undergone segmentation and encountered an error in reassembly.
INT cdd564RxSignalLevel	1.3.6.1.4.1.6247.25.1.8.2.1.1.4	INTEGER	read-only	Unit returns the value of the Rx signal level, in dBm, between -20 and -99 dBm, Returns -100 if signal is less than -99dBm. Returns -19 if signal is greater than -20dBm.
INT cdd564RxStatsIndex	1.3.6.1.4.1.6247.25.1.6.3.1.1.1	INTEGER	read-only	The Rx index for the satellite interface, where index can be from 1 to 4.
INT cdd564RxSymbolRate	1.3.6.1.4.1.6247.25.1.7.1.1.1.14	INTEGER	read-only	Rx symbol rate in symbols per second (sym) Units = sym Resolution = 1 sym
cdd564RxTable	1.3.6.1.4.1.6247.25.1.7.1.1		not-accessible	The table of Demodulators.
INT cdd564RxTableIndex	1.3.6.1.4.1.6247.25.1.7.1.1.1.1	INTEGER	read-only	The index for the Rx table, where index can be from 1 to 4.
INT cdd564SatelliteClearCounters	1.3.6.1.4.1.6247.25.1.6.3.2	INTEGER	read-write	This is a SET command for clearing all the Satellite statistic counters.
cdd564SatelliteRxStatsEntry	1.3.6.1.4.1.6247.25.1.6.3.1.1		not-accessible	The entry for the Satellite interface statistics table.
cdd564SatelliteRxStatsTable	1.3.6.1.4.1.6247.25.1.6.3.1		not-accessible	The table for Satellite interface statistics.
cdd564SatelliteStatistics	1.3.6.1.4.1.6247.25.1.6.3
INT cdd564SaveParamToFlash	1.3.6.1.4.1.6247.25.1.5.3.2	INTEGER	read-write	This is a SET command to save the configuration to the parameter file in flash.
STR cdd564SerialNumber	1.3.6.1.4.1.6247.25.1.8.1.1	DisplayString	read-only	Unit's 9-digit serial number.
cdd564SMTP	1.3.6.1.4.1.6247.25.1.1.4
STR cdd564SMTPDomain	1.3.6.1.4.1.6247.25.1.1.4.2	DisplayString	read-write	The SMTP Domain for sending problem reports. This value should be comtechefdata.com.
IP cdd564SMTPServerIPAddress	1.3.6.1.4.1.6247.25.1.1.4.1	IpAddress	read-write	The IP address of the SMTP server for sending problem reports. This IP adderess should correspond to a local Mail server.
STR cdd564SMTPUserName	1.3.6.1.4.1.6247.25.1.1.4.3	DisplayString	read-write	The user name for sending problem reports. This value should be cdmipsupport.
cdd564SNMP	1.3.6.1.4.1.6247.25.1.1.5
STR cdd564SNMPAuthenticationFailureCommunity	1.3.6.1.4.1.6247.25.1.1.5.4	DisplayString	accessible-for-notify	The community that did not match valid SNMP Read or Write community. Note: This is ONLY used in the Authentication Failure trap.
IP cdd564SNMPAuthenticationFailureIPAddress	1.3.6.1.4.1.6247.25.1.1.5.5	IpAddress	accessible-for-notify	The IP address that did not send a valid SNMP Read or Write community. Note: This is ONLY used in the Authentication Failure trap.
STR cdd564SNMPTrapCommunity	1.3.6.1.4.1.6247.25.1.1.5.2	DisplayString	read-write	The community that will be included in SNMP notifications (traps) that are sent from unit.
IP cdd564SNMPTrapDestinationIPAddress	1.3.6.1.4.1.6247.25.1.1.5.1	IpAddress	read-write	The IP address were SNMP notifications (traps) are to be sent. This IP address should correspond to a SNMP manager or browser.
IP cdd564SNMPTrapDestinationIPAddress2	1.3.6.1.4.1.6247.25.1.1.5.6	IpAddress	read-write	The secondary IP address were SNMP notifications (traps) are to be sent. This IP address should correspond to a secondary SNMP manager or browser.
INT cdd564SNMPTrapVersion	1.3.6.1.4.1.6247.25.1.1.5.3	INTEGER	read-write	The SNMP version that will be used when sending traps from the unit. SNMPv1 will send V1 traps. SNMPv2 will send V2 notifications.
STR cdd564SoftwareRevision	1.3.6.1.4.1.6247.25.1.8.1.2	DisplayString	read-only	Unit returns the value of the internal software revision installed in the unit, in the form of x.x.x.
INT cdd564StatisticAvgEbNo	1.3.6.1.4.1.6247.25.1.8.5.1.1.5	INTEGER	read-only	Minimum Eb/No during sample period. Units = 0.1 dB. Returns 999 if demod was unlocked during sample period.
STR cdd564StatisticDate	1.3.6.1.4.1.6247.25.1.8.5.1.1.3	DisplayString	read-only	The date of the statistic in the form dd/mm/yy, where: dd = day of the month (01 to 31) mm = month (01 to 12) yy = year (00 to 99)
INT cdd564StatisticDemod	1.3.6.1.4.1.6247.25.1.8.5.1.1.1	INTEGER	read-only	The demod index for which statistics table is being returned.
INT cdd564StatisticIndex	1.3.6.1.4.1.6247.25.1.8.5.1.1.2	INTEGER	read-only	The index in one of the four demod's stored statistics table.
INT cdd564StatisticMinEbNo	1.3.6.1.4.1.6247.25.1.8.5.1.1.6	INTEGER	read-only	Minimum Eb/No during sample period. Units = 0.1 dB. Returns 999 if demod was unlocked during sample period.
cdd564Statistics	1.3.6.1.4.1.6247.25.1.6
INT cdd564StatisticsSampleInterval	1.3.6.1.4.1.6247.25.1.8.5.2.1.2	INTEGER	read-write	Used to set the sample interval for the statistics logging function, where the enumerated lists goes from 0 to 9 in 10 minute steps. Setting 0 disables the statistics logging function.
STR cdd564StatisticTime	1.3.6.1.4.1.6247.25.1.8.5.1.1.4	DisplayString	read-only	The time of the statistic in the form hh:mm:ss, indicating the time from midnight, where: hh = hours (00 to 23) mm = minutes (00 to 59) ss = seconds (00 to 59)
cdd564StoredEvents	1.3.6.1.4.1.6247.25.1.8.4
cdd564StoredEventsEntry	1.3.6.1.4.1.6247.25.1.8.4.1.1		not-accessible	The entry for stored events table for all 4 demods.
cdd564StoredEventsTable	1.3.6.1.4.1.6247.25.1.8.4.1		not-accessible	The table of stored events for all four demods.
cdd564StoredStatistics	1.3.6.1.4.1.6247.25.1.8.5
cdd564StoredStatisticsConfigEntry	1.3.6.1.4.1.6247.25.1.8.5.2.1		not-accessible	The entry for the stored statistics configuration table.
INT cdd564StoredStatisticsConfigIndex	1.3.6.1.4.1.6247.25.1.8.5.2.1.1	INTEGER	read-only	The index for the Demodulator.
cdd564StoredStatisticsConfigTable	1.3.6.1.4.1.6247.25.1.8.5.2		not-accessible	The configuration for the stored statistics (per Demod).
cdd564StoredStatisticsEntry	1.3.6.1.4.1.6247.25.1.8.5.1.1		not-accessible	The entry for stored statistics table for all four demods.
cdd564StoredStatisticsTable	1.3.6.1.4.1.6247.25.1.8.5.1		not-accessible	The table of stored statistics for all four demods.
INT cdd564SubnetMaskLen	1.3.6.1.4.1.6247.25.1.2.1.4	INTEGER	read-write	The subnet mask length of the IP address.
INT cdd564Telnet	1.3.6.1.4.1.6247.25.1.1.2.2	INTEGER	read-write	Enable or disable telnet access to unit.
INT cdd564Temperature	1.3.6.1.4.1.6247.25.1.8.1.5	INTEGER	read-only	Unit returns the value of the internal temperature, in degrees Celsius.
C32 cdd564TotalBroadcastsToEthernet	1.3.6.1.4.1.6247.25.1.6.1.1.4	Counter32	read-only	The total number of Broadcast packets routed to the Ethernet interface.
C32 cdd564TotalDroppedPackets	1.3.6.1.4.1.6247.25.1.6.1.5.1	Counter32	read-only	The total number of packets dropped by the router.
C32 cdd564TotalMulticastsToEthernet	1.3.6.1.4.1.6247.25.1.6.1.1.3	Counter32	read-only	The total number of Multicast packets routed to the Ethernet interface.
C32 cdd564TotalPacketsFromEndstation	1.3.6.1.4.1.6247.25.1.6.1.3.1	Counter32	read-only	The total number of packets received from the Endstation to be sent out one of the interfaces.
C32 cdd564TotalPacketsFromEthernet	1.3.6.1.4.1.6247.25.1.6.1.1.5	Counter32	read-only	The total number of IP packets received from the Ethernet interface.
C32 cdd564TotalPacketsFromSatellite	1.3.6.1.4.1.6247.25.1.6.1.2.1	Counter32	read-only	The total number of IP packets received from the satellite interfaces.
C32 cdd564TotalPacketsToEndstation	1.3.6.1.4.1.6247.25.1.6.1.3.2	Counter32	read-only	The total number of packets sent to the Endstation from one of the interfaces.
C32 cdd564TotalPacketsToEthernet	1.3.6.1.4.1.6247.25.1.6.1.1.1	Counter32	read-only	The total number of IP packets routed to the Ethernet interface.
C32 cdd564TotalUnicastsToEthernet	1.3.6.1.4.1.6247.25.1.6.1.1.2	Counter32	read-only	The total number of Unicast packets routed to the Ethernet interface.
INT cdd564UnitAlarm	1.3.6.1.4.1.6247.25.1.8.1.4	INTEGER	read-only	Modem Unit Faults: Value Description of unit fault 0 No faults 1 +5 Volt power supply 2 +12 Volt power supply 3 -5 Volt power supply 4 +23 Volt power supply 5 -12 Volt power supply 6 Rx 1st LO synthesize lock 7 Rx 2nd LO synthesize lock 8 Ref PLL lock 9 EEPROM checksum error
NTF cdd564UnitAlarmNotification	1.3.6.1.4.1.6247.25.2.0.1			Trap for Unit alarms.
cdd564UnitInformation	1.3.6.1.4.1.6247.25.1.5.1
cdd564UnitMonitor	1.3.6.1.4.1.6247.25.1.8.1
INT cdd564UpgradeImage	1.3.6.1.4.1.6247.25.1.5.2.2	INTEGER	read-write	Specifies which image will be overwritten during an upgrade: oldest - overwrites the oldest image determined by build date. image 1 - overwrites image 1 image 2 - overwrites image 2 NOTE: Set this value before performing an upgrade.
cdd564Util	1.3.6.1.4.1.6247.25.1.9
INT cdd564WorkingMode	1.3.6.1.4.1.6247.25.1.1.2.6	INTEGER	read-write	Configure the system's working mode. The CDM-IP can operate in any of these modes. 1. Router - Small Network Mode - The system functions as router and uses the route table to determine how to forward packets in a small network HDLC address mode. The HDLC packet uses a 1 byte HDLC address. The valid values are from 1 to 254 (0x1 - 0xFE). 2. Router - Small Network Mode - The system functions as router and uses the route table to determine how to forward packets in a large network HDLC address mode. The HDLC packet uses a 2- byte HDLC address. The valid values are from 1 to 32766 (0x1 - 0x7FFE). 3. Router - Point To Point Mode - The system functions as router but does not use HDLC addresses. 4. Router - Vipersat Mode - The system functions as router and is configured to work in a Vipersat network. * IMPORTANT NOTE * Changing Working mode requires the system to reboot. System configuration is saved before rebooting. Please make sure you are setting the correct value.
INT cddRxBERMultiplier	1.3.6.1.4.1.6247.25.1.8.2.1.1.7	INTEGER	read-only	Estimated corrected BER. The BER is calculated by multiplying the Multiplier by 10E-10. Calculuation: RxBER = (Multiplier) * 0.0000000001 Returns 2147483647 (max int) if demod is unlocked.
INT cdm564LLNBLowCurrentLimit	1.3.6.1.4.1.6247.25.1.7.4.1.1.4	INTEGER	read-write	LNB lower alarm limit for current, between 10 and 400 mA.

RFC description

Comtech EF Data CDD-564 satellite demodulator configuration and monitoring.

Start monitoring Comtech EF Data CDD-564 satellite demodulator with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CDD-564

What Is CDD-564?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description