AC-SYSTEM-MIB

All MIBs › AC-SYSTEM-MIB

Organization: AudioCodes Ltd

Last Updated: 2010-01-24

Category: Telephony and VoIP, Vendor: AudioCodes

Description: Provides system-wide management objects for AudioCodes devices, including device identification, software version, reset control, and administrative configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AC-SYSTEM-MIB?

AC-SYSTEM-MIB is AudioCodes' core enterprise MIB for system-wide management of its VoIP gateways and media servers, covering device identification, software/firmware version reporting, remote reset control, and general administrative configuration. It exposes objects that identify the running software version and hardware/product type, along with controls to trigger a device reset or apply administrative settings. As a status/health MIB it is central to confirming a device's software version, important for tracking firmware compliance, and its basic administrative identity, complementing the deeper performance data found in AC-PM-SYSTEM-MIB. It is the foundational AudioCodes system MIB that the other AudioCodes MIBs (AC-CONTROL-MIB, the AC-PM-* series) are typically deployed alongside for a complete management picture. It is used across the full range of AudioCodes Mediant gateway and media server products in VoIP deployments. Engineers can download the AC-SYSTEM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in AC-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

AudioCodes VoIP gateway
AudioCodes media server

Monitoring Examples

An operator polls the device-identification and software-version objects to confirm every gateway in a fleet is running the expected firmware release, and uses the reset-control object, when authorized, to remotely reboot a device stuck in a bad state. If a reported software version differs unexpectedly from the fleet baseline after a maintenance window, that flags a failed or partial upgrade needing follow-up.

What Can Be Monitored

device identification/product type
software/firmware version
remote reset control state
administrative configuration settings

Imported Objects

From AUDIOCODES-TYPES-MIB

acBoardMibs	OBJECT-IDENTITY
acGeneric	OBJECT-IDENTITY
acProducts	OBJECT-IDENTITY
acRegistrations	OBJECT-IDENTITY
audioCodes	OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From RFC1155-SMI

IpAddress

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TAddress
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
acFirewall	1.3.6.1.4.1.5003.9.10.10.1.7.23
acMultipleIP	1.3.6.1.4.1.5003.9.10.10.1.3.1.30
INT acMultipleIPEnable	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.1	INTEGER	read-write	Enables the multiple IPs feature. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: EnableMultipleIPs
INT acMultipleIPEnableDNSasOAM	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.3	INTEGER	read-write	Sets the location of the DNS. If this parameter is set and the machine is functioning in multiple IPs mode, the DNS is located on the OAM network. If not, the DNS is on the control network. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: EnableDNSasOAM
INT acMultipleIPEnableNetwotkSeparation	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.6	INTEGER	read-write	Enables Network Physical Separation. Allows the user to have separate port for each Network. Requires suitable hardware. 0 = Disabled 1 = Enabled. Access: Offline. AC INI-Param: ENABLENETWORKPHYSICALSEPARATION
INT acMultipleIPEnableNTPasOAM	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.4	INTEGER	read-write	Sets the location of the Network Time Protocol (NTP). If this parameter is set and the machine is functioning in multiple IPs mode, the NTP is located on the OAM network. If not, the NTP is located on the control network. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: EnableNTPasOAM
INT acMultipleIPEnableSCTPasControl	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.5	INTEGER	read-write	Sets the location of the Stream Control Transmission Protocol (SCTP). If this parameter is set and the machine is functioning in multiple IPs mode, the SCTP is located on the control network. If not, the SCTP is located on the OAM network. 0 = Default 1 = Enable. Access: Offline. AC INI-Param: EnableSCTPasControl
INT acMultipleIPEnableTPNCPasOAM	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.2	INTEGER	read-write	Sets the TPNCP location on the Operation, Administration and Management (OAM) network, when operating in multiple IPs mode. If this parameter is set and the machine is working in multiple IPs mode, TPNCP is located on the OAM network. 0 = TPNCP on Control network 1 = TPNCP on OAM network. Access: Offline. AC INI-Param: EnableTPNCPasOAM
INT acMultipleIPInterfaceTableAction	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.7	INTEGER	read-write	This is an action object. Set this to validateConfiguration(2) when you want the configuration in the acSysInterfaceTable to be validated immediately (as opposed to at reset). done(1) is the default value for any GET on this object. The results of the action should be followed in the syslog. Access: Instant. AC INI-Param: N/A
INT acNetworkIPAdminState	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.21.1.6	INTEGER	read-write	Determines if a row is currentely active or not. Lock(1) - the row is in configuration (non active) state. UnLock(2) - row is in active state. Access: Online. AC INI-Param: N/A
acNetworkIPEntry	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.21.1		not-accessible
U32 acNetworkIPIfIndex	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.21.1.2	Unsigned32	read-only	The row's index in the IF MIB. The IF MIB is not yet supported and so for now this is the same as the ipCidrRouteIfIndex object. 0 = OAM 1 = Media 2 = Control. AC INI-Param: N/A
INT acNetworkIPIndex	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.21.1.1	INTEGER	not-accessible	The row's index. AC INI-Param: N/A
IP acNetworkIPLocalDefGW	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.21.1.5	IpAddress	read-write	Sets the Default gateway for the OAM interface when operating in multiple IPs mode. Range: Legal IP address in subnet Default = 0.0.0.0. Access: Online. AC INI-Param: N/A
IP acNetworkIPLocalIPAddress	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.21.1.3	IpAddress	read-write	Sets the IP address of the OAM (Operation, Administration & Management) when operating in multiple IPs mode. Range: Legal IP address Default = 0.0.0.0. Access: Online. AC INI-Param: N/A
IP acNetworkIPLocalSubnetMask	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.21.1.4	IpAddress	read-write	Sets the Subnet Mask for the OAM interface, when operating in multiple IPs mode. Range: Legal Subnet Default = 0.0.0.0. Access: Online. AC INI-Param: N/A
acNetworkIPTable	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.21		not-accessible	IP control table. Enables to add, remove or configure the device's networks.
acSys802dot1x	1.3.6.1.4.1.5003.9.10.10.1.7.25
INT acSys802dot1xMode	1.3.6.1.4.1.5003.9.10.10.1.7.25.1	INTEGER	read-write	Enables support for IEEE 802.1x physical port security. 0 = Disabled 1 = EAP-MD5 2 = Protected EAP (PEAP) 3 = EAP-TLS . Access: Instant. AC INI-Param: 802.1xMode
STR acSys802dot1xPassword	1.3.6.1.4.1.5003.9.10.10.1.7.25.3	SnmpAdminString	read-write	Password for IEEE 802.1x support. Access: Instant. AC INI-Param: 802.1xPassword
STR acSys802dot1xUsername	1.3.6.1.4.1.5003.9.10.10.1.7.25.2	SnmpAdminString	read-write	Username for IEEE 802.1x support. Access: Instant. AC INI-Param: 802.1xUsername
INT acSys802dot1xVerifyPeerCertificate	1.3.6.1.4.1.5003.9.10.10.1.7.25.4	INTEGER	read-write	Verify Peer Certificate for IEEE 802.1x support. Access: Instant. AC INI-Param: 802.1xVerifyPeerCertificate
INT acSysAccessListAction	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.3	INTEGER	read-create	Mangement Field for ACTIONS. Internal parameter. AC INI-Param: N/A
INT acSysAccessListActionRes	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.4	INTEGER	read-only	Mangement Field for ACTIONS RESULT. Internal parameter. AC INI-Param: N/A
INT acSysAccessListAllowType	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.13	INTEGER	read-create	Allow or block traffic matching this rule. Access: Online. AC INI-Param: ACCESSLIST_Allow_Type
U32 acSysAccessListByteBurst	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.12	Unsigned32	read-create	Allowed traffic burst in bytes (0 = unused). Access: Online. AC INI-Param: ACCESSLIST_Byte_Burst
U32 acSysAccessListByteRate	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.11	Unsigned32	read-create	Allowed traffic in bytes per second (0 = unused). Access: Online. AC INI-Param: ACCESSLIST_Byte_Rate
U32 acSysAccessListEndPort	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.8	Unsigned32	read-create	Port range - end. Access: Online. AC INI-Param: ACCESSLIST_End_Port
acSysAccessListEntry	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1		not-accessible
U32 acSysAccessListIndex	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.1	Unsigned32	not-accessible	Index Field for line. Internal parameter. AC INI-Param: ACCESSLIST_Index
U32 acSysAccessListMatchCount	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.14	Unsigned32	read-only	Statistics: number of matched packets. AC INI-Param: ACCESSLIST_MatchCount
IP acSysAccessListNetMask	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.6	IpAddress	read-create	Mask for this access rule (bitwise ANDed with the source IP of the packet). Access: Online. AC INI-Param: ACCESSLIST_Net_Mask
U32 acSysAccessListPacketSize	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.10	Unsigned32	read-create	Maximum packet size (0 = unused). Access: Online. AC INI-Param: ACCESSLIST_Packet_Size
STR acSysAccessListProtocol	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.9	SnmpAdminString	read-create	IP user-level protocol (TCP, UDP, ICMP, ESP, SIP, MGCP, TPNCP, ANY or numeric value). Access: Online. AC INI-Param: ACCESSLIST_Protocol
ROW acSysAccessListRowStatus	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.2	RowStatus	read-create	ROWSTATUS field for line. Internal parameter. AC INI-Param: N/A
STR acSysAccessListSourceIP	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.5	SnmpAdminString	read-create	Source IP for access rule. Access: Online. AC INI-Param: ACCESSLIST_Source_IP
U32 acSysAccessListStartPort	1.3.6.1.4.1.5003.9.10.10.1.7.23.1.1.7	Unsigned32	read-create	Port range - start. Access: Online. AC INI-Param: ACCESSLIST_Start_Port
acSysAccessListTable	1.3.6.1.4.1.5003.9.10.10.1.7.23.1		not-accessible
acSysAction	1.3.6.1.4.1.5003.9.10.10.3.1
acSysActionAdmin	1.3.6.1.4.1.5003.9.10.10.3.1.2
INT acSysActionAdminState	1.3.6.1.4.1.5003.9.10.10.3.1.2.1	INTEGER	read-write	Determines the gateway's operational state. 0 - locked: Shutdown the GW In the time frame set by acgwAdminStateLockControl. 1 - shuttingDown: (read only) Graceful Shutdown is being carried out. 2 - unlocked: GW is in service. Access: Online. AC INI-Param: N/A
I32 acSysActionAdminStateLockTimeout	1.3.6.1.4.1.5003.9.10.10.3.1.2.2	Integer32	read-write	Defines the time remaining (in seconds) for the shutdown to complete. 0 = immediate shutdown -1 = waits until all calls drop (infinite) >0 = the number of seconds to wait. Access: Offline. AC INI-Param: N/A
acSysActionSet	1.3.6.1.4.1.5003.9.10.10.3.1.1
U32 acSysActionSetActionId	1.3.6.1.4.1.5003.9.10.10.3.1.1.12	Unsigned32	read-write	This field is for management use and is aimed to distinguish different managers managing a single device. Access: Instant. AC INI-Param: N/A
U32 acSysActionSetAutoUpdate	1.3.6.1.4.1.5003.9.10.10.3.1.1.5	Unsigned32	read-write	To update the system configuration according to the provisioned IniFileUrl, set the value of this object to 1. Access: Instant. AC INI-Param: N/A
STR acSysActionSetAutoUpdateActionResult	1.3.6.1.4.1.5003.9.10.10.3.1.1.13	SnmpAdminString	read-only	Indicates the autoupdates operation status in the form of a string: 'acSysActionId ; ; '. The status field can be: 'success'\'failure'\'inProgress'. The infromation is valid only when downloading one file at a time. Note - a second way of following the success of the file downloading is to see the files name being updated in the acSysFile subtree. AC INI-Param: N/A
INT acSysActionSetConvertNetworkIFsConfiguration	1.3.6.1.4.1.5003.9.10.10.3.1.1.11	INTEGER	read-write	SET to 1 will convert network configuration to advance multiple network Interfaces mode. Access: Instant. AC INI-Param: N/A
U32 acSysActionSetDefaults	1.3.6.1.4.1.5003.9.10.10.3.1.1.3	Unsigned32	read-write	To set the board to default values, set the value of this object to 1. Access: Instant. AC INI-Param: N/A
U32 acSysActionSetGetTimeFromNTPServer	1.3.6.1.4.1.5003.9.10.10.3.1.1.6	Unsigned32	read-write	Initiates an immediate NTP time fetch. Access: Instant. AC INI-Param: N/A
INT acSysActionSetGWAppTLSUpgrade	1.3.6.1.4.1.5003.9.10.10.3.1.1.10	INTEGER	read-write	To update the GWApp TLS configuration according to the provisioned TLS fils URL set the value of this object to 1. Access: Instant. AC INI-Param: N/A
INT acSysActionSetIPSecTLSUpgrade	1.3.6.1.4.1.5003.9.10.10.3.1.1.9	INTEGER	read-write	To update the IPSec TLS configuration according to the provisioned TLS fils URL set the value of this object to 1. Access: Instant. AC INI-Param: N/A
INT acSysActionSetOnLineChangesApply	1.3.6.1.4.1.5003.9.10.10.3.1.1.8	INTEGER	read-write	Applies the board on line changed params. Access: Instant. AC INI-Param: N/A
U32 acSysActionSetReset	1.3.6.1.4.1.5003.9.10.10.3.1.1.1	Unsigned32	read-write	remote Reset. To remote reset the board, set the value of this object to 1. Note: Before Reset, The current boardConfiguration parameters will be burned to the board. Access: Instant. AC INI-Param: N/A
INT acSysActionSetResetControl	1.3.6.1.4.1.5003.9.10.10.3.1.1.2	INTEGER	read-write	Determines the remote reset action. 1 - burn staged load image, if any, and config to flash, perform a reset, and load from flash 2 - perform a reset, and load from flash (staged load image, if any, and config is not burned to flash) 3 - perform a reset, and load from bootp/tftp (staged load image, if any, and config burn is not needed) * - an error is returned for any other value Note: The staged load image is an image of a cmp file that was previously loaded to a area in RAM via an HTTP upload. Access: Instant. AC INI-Param: RemoteResetControl
U32 acSysActionSetSaveConfig	1.3.6.1.4.1.5003.9.10.10.3.1.1.4	Unsigned32	read-write	To save all current configuration in the board onto the flash, set the value of this object to 1. NOTE: Do NOT save the configuration while voice is running - this will cause a delay. Access: Instant. AC INI-Param: N/A
INT acSysActionSetSwUpgrade	1.3.6.1.4.1.5003.9.10.10.3.1.1.7	INTEGER	read-write	Defines the type of SW upgrade in M3K HA system (Hitless or system reset). Access: Instant. AC INI-Param: M3KHASwUpgradeMode
acSysAMS	1.3.6.1.4.1.5003.9.10.10.1.10
IP acSysAMSApsIpAddress	1.3.6.1.4.1.5003.9.10.10.1.10.2	IpAddress	read-write	Sets the destination UDP port to which the Heartbeat Packets are sent. Range = IP address in dotted notation xxx.xxx.xxx.xxx Default = 0.0.0.0. Access: Offline. AC INI-Param: HeartbeatDestIP
U32 acSysAMSApsPort	1.3.6.1.4.1.5003.9.10.10.1.10.3	Unsigned32	read-write	Sets the destination UDP port to which the heartbeat packets are sent. Access: Offline. AC INI-Param: HeartbeatDestPort
INT acSysAMSAPSProfile	1.3.6.1.4.1.5003.9.10.10.1.10.6	INTEGER	read-write	Indicates if the system should expect to use APS bundle (vp.dat and segments.xml files), or if the system should expect the vp.dat file only. A 1 means that an APS bundle should be used. A 0 means that the system should use vp.dat only. The default setting is 1, meaning expect APS bundle. Access: Offline. AC INI-Param: APSEnabled
INT acSysAMSForceRepositoryEnable	1.3.6.1.4.1.5003.9.10.10.1.10.7	INTEGER	read-write	Indicates that a new audio repository (consisting of VP and XML files) should always be uploaded to the board regardless of whether signals are still being played on the old repository. Access: Instant. AC INI-Param: AMSForceRepositoryUpdateEnabled
STR acSysAMSPrimaryLanguage	1.3.6.1.4.1.5003.9.10.10.1.10.4	SnmpAdminString	read-write	Defines the Primary Language for the AMS. Range = String[3] - language ISO string. Access: Instant. AC INI-Param: AMSPrimaryLanguage
U32 acSysAMSProfile	1.3.6.1.4.1.5003.9.10.10.1.10.1	Unsigned32	read-write	Enable/Disable AMS Advanced IVR play functionality. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: AMSProfile
STR acSysAMSSecondaryLanguage	1.3.6.1.4.1.5003.9.10.10.1.10.5	SnmpAdminString	read-write	Defines the Secondary Language for the AMS. Range = String[3] - language ISO string. Access: Instant. AC INI-Param: AMSSecondaryLanguage
acSysControl	1.3.6.1.4.1.5003.9.10.10.1.1
INT acSysControlProtocolType	1.3.6.1.4.1.5003.9.10.10.1.1.1	INTEGER	read-write	Defines the control protocol type. Choose either: 0 = None 1 = MGCP 2 = MEGACO 4 = H.323 8 = SIP. Access: Offline. AC INI-Param: MGCONTROLPROTOCOLTYPE
INT acSysControlTrunkingToAnalogFunctionalityProfile	1.3.6.1.4.1.5003.9.10.10.1.1.2	INTEGER	read-write	This parameter defines the Trunking to Analog Functionality Profile. 0 = Disable 1 = Enable MelCAS/LoopStart/GroundStart to Analog Functionality Refer to the enumerator acTrunkingToAnalogFunctionalityProfile enum for the possible values. Access: Offline. AC INI-Param: TrunkingToAnalogFunctionalityProfile
acSysCount	1.3.6.1.4.1.5003.9.10.10.2.4
U32 acSysCountChannels	1.3.6.1.4.1.5003.9.10.10.2.4.2	Unsigned32	read-only	Channel Count. AC INI-Param: N/A
U32 acSysCountDSPs	1.3.6.1.4.1.5003.9.10.10.2.4.1	Unsigned32	read-only	DSP Count. AC INI-Param: N/A
U32 acSysCountTrunks	1.3.6.1.4.1.5003.9.10.10.2.4.3	Unsigned32	read-only	Trunks Count. AC INI-Param: N/A
acSysDayLightSavingTime	1.3.6.1.4.1.5003.9.10.10.1.3.3.21
STR acSysDayLightSavingTimeEnd	1.3.6.1.4.1.5003.9.10.10.1.3.3.21.4	SnmpAdminString	read-write	This parameter defines the date and time of ending day light time in current year. Format mo:dd:hh:mm. Access: Instant. AC INI-Param: DayLightSavingTimeEnd
INT acSysDayLightSavingTimeMode	1.3.6.1.4.1.5003.9.10.10.1.3.3.21.1	INTEGER	read-write	Determines whether to enable the time ajustment to day light saving time while update time from NTP server. Access: Instant. AC INI-Param: DayLightSavingTimeEnable
U32 acSysDayLightSavingTimeOffset	1.3.6.1.4.1.5003.9.10.10.1.3.3.21.2	Unsigned32	read-write	when DayLightSavingTimeEnable is Enable, this parametes determine the fix size in minutes: 0-120. Access: Instant. AC INI-Param: DayLightSavingTimeOffset
STR acSysDayLightSavingTimeStart	1.3.6.1.4.1.5003.9.10.10.1.3.3.21.3	SnmpAdminString	read-write	This parameter defines the date and time of starting day light time in current year. Format mo:dd:hh:mm. Access: Instant. AC INI-Param: DayLightSavingTimeStart
acSysDiagnostics	1.3.6.1.4.1.5003.9.10.10.1.4.1
INT acSysDiagnosticsEnable	1.3.6.1.4.1.5003.9.10.10.1.4.1.1	INTEGER	read-write	Checks the correct functionality of the different hardware components on the board. On completion of the check, the board sends an EV_END_BIT value, which contains information on the test results of each hardware component. 0 = No diagnostics (default) 1 = Perform diagnostics (full test of DSPs, PCM, Switch, LAN, PHY and Flash) 2 = Perform diagnostics (full test of DSPs, PCM, Switch, LAN, PHY, but partial, test of Flash, a quicker mode). Access: Offline. AC INI-Param: ENABLEDIAGNOSTICS
INT acSysDiagnosticsEnablePerformanceThresholdAlarms	1.3.6.1.4.1.5003.9.10.10.1.4.1.2	INTEGER	read-write	This parameter enables sending SNMP traps and Syslog messages when performance of the device is degraded (according to the configured thresholds). Access: Instant. AC INI-Param: PM_EnableThresholdAlarms
STR acSysDiagnosticsListOfActivitiesToLog	1.3.6.1.4.1.5003.9.10.10.1.4.1.3	SnmpAdminString	read-write	This parameter defines what activities are to be reported by the device in the form of a log message. Parameter format is x,y,z-... where x,y,z are activity codes to be reported by the device. Supported activity codes: PVC - Parameter Value Changes. AFL - Auxiliary Files Loading. DR - Device Reset. FB - Flash Burning. SWU - SoftWareUpdate. ARD - Access to Restricted Domains. NAA - Non Authorized Access. SPC - Sensitive Parameters Changes. Access: Online. AC INI-Param: ActivityListToLog
acSysEthernet	1.3.6.1.4.1.5003.9.10.10.2.6.1
U32 acSysEthernetActivePortNumber	1.3.6.1.4.1.5003.9.10.10.2.6.1.5	Unsigned32	read-only	Display the current active ethernet port number. 0 - not relevant. AC INI-Param: N/A
INT acSysEthernetFirstPortDuplexMode	1.3.6.1.4.1.5003.9.10.10.2.6.1.1	INTEGER	read-only	full-duplex or half-duplex connection. AC INI-Param: N/A
INT acSysEthernetFirstPortSpeed	1.3.6.1.4.1.5003.9.10.10.2.6.1.2	INTEGER	read-only	AC INI-Param: N/A
acSysEthernetPort	1.3.6.1.4.1.5003.9.10.10.1.3.12
INT acSysEthernetPortPhyConfiguration	1.3.6.1.4.1.5003.9.10.10.1.3.12.1	INTEGER	read-write	Controls the Ethernet connection mode type. Auto-negotiate falls back to Half-Duplex mode (HD) when the opposite port is not in Auto-negotiate mode. The speed (10 Base-T or 100 Base-TX) in this mode is always configured correctly. 0 = 10 Base-T half-duplex 1 = 10 Base-T full-duplex 2 = 100 Base-TX half-duplex 3 = 100 Base-TX full-duplex 4 = Auto-negotiate. Access: Offline. AC INI-Param: EthernetPhyConfiguration
INT acSysEthernetSecondPortDuplexMode	1.3.6.1.4.1.5003.9.10.10.2.6.1.3	INTEGER	read-only	full-duplex or half-duplex connection. AC INI-Param: N/A
INT acSysEthernetSecondPortSpeed	1.3.6.1.4.1.5003.9.10.10.2.6.1.4	INTEGER	read-only	AC INI-Param: N/A
INT acSysEthernetStatusActivePortNumber	1.3.6.1.4.1.5003.9.10.10.2.6.1.21.1.4	INTEGER	read-only	Status of ethernet port - active or not active. AC INI-Param: N/A
acSysEthernetStatusEntry	1.3.6.1.4.1.5003.9.10.10.2.6.1.21.1		not-accessible
U32 acSysEthernetStatusIndex	1.3.6.1.4.1.5003.9.10.10.2.6.1.21.1.1	Unsigned32	not-accessible	The row's index. On 8410 Systems: Index 1 � related to GBE port no.1 in the TER (Media). Index 2 � related to GBE port no.2 in the TER (Media). Index 3 � related to port 1A in PEM #1 (Control). Index 4 � related to port 1B in PEM #2 (Control). Index 5 � related to port 2A in PEM #1 (OAM). Index 6 � related to port 2B in PEM #2 (OAM). On MSBG only: 0 - WAN interface. 1-12 LAN interfaces. AC INI-Param: N/A
INT acSysEthernetStatusPortDuplexMode	1.3.6.1.4.1.5003.9.10.10.2.6.1.21.1.2	INTEGER	read-only	full-duplex or half-duplex connection. AC INI-Param: N/A
INT acSysEthernetStatusPortSpeed	1.3.6.1.4.1.5003.9.10.10.2.6.1.21.1.3	INTEGER	read-only	port speed. AC INI-Param: N/A
INT acSysEthernetStatusPortState	1.3.6.1.4.1.5003.9.10.10.2.6.1.21.1.5	INTEGER	read-only	Port State. AC INI-Param: N/A
INT acSysEthernetStatusPowerOverEthernet	1.3.6.1.4.1.5003.9.10.10.2.6.1.21.1.6	INTEGER	read-only	Power over Ethernet interface status. AC INI-Param: N/A
acSysEthernetStatusTable	1.3.6.1.4.1.5003.9.10.10.2.6.1.21		not-accessible	Ethernet relevant information
acSysFanTrayEntry	1.3.6.1.4.1.5003.9.10.10.4.22.1		not-accessible
INT acSysFanTrayExistence	1.3.6.1.4.1.5003.9.10.10.4.22.1.3	INTEGER	read-only	Is the Fan-Tray present or missing. AC INI-Param: N/A
OCT acSysFanTrayFansConfiguredSpeed	1.3.6.1.4.1.5003.9.10.10.4.22.1.7	OCTET STRING	read-only	The fan's configured speed in Tach units (RPM/120). Each Byte represents a fan. AC INI-Param: N/A
OCT acSysFanTrayFansCurrentSpeed	1.3.6.1.4.1.5003.9.10.10.4.22.1.8	OCTET STRING	read-only	The fan's mesured speed in Tach units (RPM/120). Each Byte represents a fan. AC INI-Param: N/A
OCT acSysFanTrayFansStatus	1.3.6.1.4.1.5003.9.10.10.4.22.1.9	OCTET STRING	read-only	A bit field which display the working status of each fan in the Fan-Tray. 0 - Working 1 - Faulty. AC INI-Param: N/A
U32 acSysFanTrayGeographicalPosition	1.3.6.1.4.1.5003.9.10.10.4.22.1.2	Unsigned32	read-only	The slot number in the chassis. AC INI-Param: N/A
U32 acSysFanTrayIndex	1.3.6.1.4.1.5003.9.10.10.4.22.1.1	Unsigned32	not-accessible	Fan-Tray's index in the system. AC INI-Param: N/A
OCT acSysFanTrayLEDs	1.3.6.1.4.1.5003.9.10.10.4.22.1.5	OCTET STRING	read-only	This object built as a bit-field which represents the Fan-Tray's LEDs status. The first four bites represent the System's LED status and the last four bites represent the Shelf-LED�s status. AC INI-Param: N/A
INT acSysFanTraySeverity	1.3.6.1.4.1.5003.9.10.10.4.22.1.6	INTEGER	read-only	The Severity of the whole fan tray according to the current active alarm in the alarm table: Critical, Major or cleared. AC INI-Param: N/A
acSysFanTrayTable	1.3.6.1.4.1.5003.9.10.10.4.22		not-accessible
STR acSysFanTrayType	1.3.6.1.4.1.5003.9.10.10.4.22.1.4	SnmpAdminString	read-only	The type of the Fan-Tray . AC INI-Param: N/A
acSysFile	1.3.6.1.4.1.5003.9.10.10.1.6
STR acSysFileCpt	1.3.6.1.4.1.5003.9.10.10.1.6.1	SnmpAdminString	read-only	Defines Call Progress Tone filenames (downloaded by TFTP). AC INI-Param: CALLPROGRESSTONESFILENAME
STR acSysFileDialPlanFileName	1.3.6.1.4.1.5003.9.10.10.1.6.7	SnmpAdminString	read-only	This parameter is used to indicate the name of the file containing the Dial Plan. AC INI-Param: gDialPlanFileName
STR acSysFileExternalCoder	1.3.6.1.4.1.5003.9.10.10.1.6.5	SnmpAdminString	read-only	Coders table file name. AC INI-Param: CODERTBLFILENAME
STR acSysFileFirstVideoFontFileName	1.3.6.1.4.1.5003.9.10.10.1.6.11	SnmpAdminString	read-only	Indicates the name of the first file containing the Video Font file index. AC INI-Param: VideoFontFIleName
STR acSysFilePrerecordedTones	1.3.6.1.4.1.5003.9.10.10.1.6.3	SnmpAdminString	read-only	Defines the name (and path) of the file containing the Prerecorded Tones. Range = String of ASCII characters. AC INI-Param: PrerecordedTonesFileName
STR acSysFileSecondVideoFontFileName	1.3.6.1.4.1.5003.9.10.10.1.6.12	SnmpAdminString	read-only	Indicates the name of the second file containing the Video Font file index. AC INI-Param: VideoFontFIleName
STR acSysFileThirdVideoFontFileName	1.3.6.1.4.1.5003.9.10.10.1.6.13	SnmpAdminString	read-only	Indicates the name of the first file containing the Video Font file index. AC INI-Param: VideoFontFIleName
STR acSysFileTLSCertFileName	1.3.6.1.4.1.5003.9.10.10.1.6.9	SnmpAdminString	read-only	Defines the name of the HTTPS server certificate file to be downloaded via TFTP. The file must be in base64-encoded PEM format. Range = String[47]. AC INI-Param: HTTPSCertFileName
STR acSysFileTLSPkeyFileName	1.3.6.1.4.1.5003.9.10.10.1.6.8	SnmpAdminString	read-only	This parameter defines the name of a private key file (internal). Set to blank to regenerate the key and certificate. AC INI-Param: HTTPSPkeyFileName
STR acSysFileTLSRootFileName	1.3.6.1.4.1.5003.9.10.10.1.6.10	SnmpAdminString	read-only	Defines the name of the HTTPS trusted root certificate file to be downloaded via TFTP. The file must be in base64-encoded PEM format. Range = String[47]. AC INI-Param: HTTPSRootFileName
STR acSysFileUserInfo	1.3.6.1.4.1.5003.9.10.10.1.6.6	SnmpAdminString	read-only	The file name to be loaded. AC INI-Param: N/A
STR acSysFileV5PortConfFileName	1.3.6.1.4.1.5003.9.10.10.1.6.14	SnmpAdminString	read-only	Indicates the name and location of the V5 Port Configuration file. AC INI-Param: V5PortConfigurationFileName
STR acSysFileVp	1.3.6.1.4.1.5003.9.10.10.1.6.2	SnmpAdminString	read-only	Defines the name (and path) of the file containing the Voice Prompts. Range = String of ASCII characters. AC INI-Param: VOICEPROMPTSFILENAME
STR acSysFileXml	1.3.6.1.4.1.5003.9.10.10.1.6.4	SnmpAdminString	read-only	This parameter is used to indicate the name of the file containing the XML file. AC INI-Param: XMLFileName
acSysGenericINI	1.3.6.1.4.1.5003.9.10.10.1.4.2
STR acSysGenericINILine	1.3.6.1.4.1.5003.9.10.10.1.4.2.1	SnmpAdminString	read-write	Flexible INI file line. Access: Offline. AC INI-Param: N/A
INT acSysGenericINISecureStartup	1.3.6.1.4.1.5003.9.10.10.1.4.2.2	INTEGER	read-write	Enables or disables secure startup mode. In this mode, downloading of the INI file is restricted to a URL provided in prior configuration (see parameter IniFileURL) or via DHCP. Access: Offline. AC INI-Param: EnableSecureStartup
acSysHA	1.3.6.1.4.1.5003.9.10.10.1.12
IP acSysHAGlobalIPAddress	1.3.6.1.4.1.5003.9.10.10.1.12.1	IpAddress	read-write	Defines the M3K global IP address to be used by the active module in HA system. (Dotted format notation. e.g., 192.10.1.255). Range = Legal IP address. Access: Offline. AC INI-Param: M3KGlobalIpAddr
acSysHAStatus	1.3.6.1.4.1.5003.9.10.10.2.10
INT acSysHAStatusReady	1.3.6.1.4.1.5003.9.10.10.2.10.1	INTEGER	read-only	Defines whether the M3K system supports HA or not. AC INI-Param: N/A
acSysHTTPClient	1.3.6.1.4.1.5003.9.10.10.1.3.8
INT acSysHTTPClientAutoUpdateCmpFile	1.3.6.1.4.1.5003.9.10.10.1.3.8.3	INTEGER	read-write	Enables / disables the automatic update mechanism for the cmp file. 0 = The automatic update mechanism doesn't apply to the cmp file (default). 1 = The automatic update mechanism includes the cmp file. Access: Offline. AC INI-Param: AutoUpdateCmpFile
U32 acSysHTTPClientAutoUpdateFrequency	1.3.6.1.4.1.5003.9.10.10.1.3.8.2	Unsigned32	read-write	Determines the number of minutes the gateway waits between automatic updates. The default value is 0 (the update at fixed intervals mechanism is disabled). Range: Any number . Access: Offline. AC INI-Param: AutoUpdateFrequency
STR acSysHTTPClientAutoUpdatePredefinedTime	1.3.6.1.4.1.5003.9.10.10.1.3.8.1	SnmpAdminString	read-write	Schedules an automatic update to a predefined time of the day. The range is 'HH:MM' (24-hour format). For example: 20:18 . Access: Offline. AC INI-Param: AutoUpdatePredefinedTime
STR acSysHTTPClientCASFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.12	SnmpAdminString	read-write	Provides a link to a Channel Associated Signaling (CAS) file to be downloaded from a remote server. Range = http://server_name/file, https://server_name/file. Access: Instant. AC INI-Param: CasFileUrl
STR acSysHTTPClientCmpFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.4	SnmpAdminString	read-write	This parameter provides a link to a software image (CMP file) to be downloaded from a remote server. . Access: Offline. AC INI-Param: CmpFileURL
STR acSysHTTPClientCoderTableFileUrl	1.3.6.1.4.1.5003.9.10.10.1.3.8.14	SnmpAdminString	read-write	Provides a link to a coder table (CTBL) file that is to be downloaded from a remote server. . Access: Instant. AC INI-Param: CoderTableFileUrl
STR acSysHTTPClientCPTFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.7	SnmpAdminString	read-write	Provides a link to a Call Progress Tones (CPT) file to be downloaded from a remote server. Range = http://server_name/file, https://server_name/file. Access: Instant. AC INI-Param: CptFileUrl
STR acSysHTTPClientDataConfigurationFileUrl	1.3.6.1.4.1.5003.9.10.10.1.3.8.23	SnmpAdminString	read-write	Provides a link to a data configuration file to be downloaded from a remote server using the Automatic Update facility. Access: Instant. AC INI-Param: RGCONFFILEURL
STR acSysHTTPClientDialPlanFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.16	SnmpAdminString	read-write	URL for downloading a Dial Plan file using the Automatic Update facility. Access: Instant. AC INI-Param: DialPlanFileUrl
STR acSysHTTPClientFXOCoeffFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.11	SnmpAdminString	read-write	Provides a link to an FXO coefficients file, to be downloaded from a remote server. Range = http://server_name/file, https://server_name/file. Access: Instant. AC INI-Param: FXOCoeffFileUrl
STR acSysHTTPClientFXSCoeffFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.10	SnmpAdminString	read-write	Provides a link to an FXS coefficients file, to be downloaded from a remote server. Range = http://server_name/file, https://server_name/file. Access: Instant. AC INI-Param: FXSCoeffFileUrl
STR acSysHTTPClientIniFileTemplateURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.6	SnmpAdminString	read-write	Provides a link to an ini file to be downloaded from a remote server, in addition to IniFileUrl. Range = http://server_name/file, https://server_name/file. Access: Offline. AC INI-Param: IniFileTemplateUrl
STR acSysHTTPClientIniFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.5	SnmpAdminString	read-write	This parameter provides a link to an ini file to be downloaded from a remote server. . Access: Offline. AC INI-Param: IniFileURL
STR acSysHTTPClientPRTFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.9	SnmpAdminString	read-write	Provides a link to a prerecorded tones dat file, to be downloaded from a remote server. Range = http://server_name/file, https://server_name/file. Access: Instant. AC INI-Param: PrtFileUrl
STR acSysHTTPClientTLSCertFileUrl	1.3.6.1.4.1.5003.9.10.10.1.3.8.18	SnmpAdminString	read-write	URL for downloading a TLS certificate file using the Automatic Update facility. Access: Offline. AC INI-Param: TLSCertFileUrl
STR acSysHTTPClientTLSPkeyFileUrl	1.3.6.1.4.1.5003.9.10.10.1.3.8.17	SnmpAdminString	read-write	URL for downloading a TLS private key file using the Automatic Update facility. Access: Offline. AC INI-Param: TLSPkeyFileUrl
STR acSysHTTPClientTLSRootFileUrl	1.3.6.1.4.1.5003.9.10.10.1.3.8.19	SnmpAdminString	read-write	URL for downloading a TLS trusted root certificate file using the Automatic Update facility. Access: Offline. AC INI-Param: TLSRootFileUrl
STR acSysHTTPClientUserInfoFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.15	SnmpAdminString	read-write	Provides a link to the user information file, to be downloaded using Automatic Update. Relevant only for H323 or SIP controlled devices. Access: Offline. AC INI-Param: UserInfoFileUrl
STR acSysHTTPClientV5PortConfFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.22	SnmpAdminString	read-write	Provides a link to a software (V5PortConfiguration file) to be downloaded from a remote server. Access: Instant. AC INI-Param: V5PortConfigurationFileURL
STR acSysHTTPClientVideoFontFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.21	SnmpAdminString	read-write	Indicates the URL for downloading a logo file for the web interface using the Automatic Update facility. Access: Offline. AC INI-Param: VideoFontFileUrl
STR acSysHTTPClientVPFileURL	1.3.6.1.4.1.5003.9.10.10.1.3.8.8	SnmpAdminString	read-write	Provides a link to a Voice Prompts file to be downloaded from a remote server. Range = http://server_name/file, https://server_name/file. Access: Instant. AC INI-Param: VpFileUrl
STR acSysHTTPClientWebLogoFileUrl	1.3.6.1.4.1.5003.9.10.10.1.3.8.20	SnmpAdminString	read-write	URL for downloading a logo file for the web interface using the Automatic Update facility. Access: Offline. AC INI-Param: WebLogoFileUrl
STR acSysHTTPClientXMLFileUrl	1.3.6.1.4.1.5003.9.10.10.1.3.8.13	SnmpAdminString	read-write	Provides a link to an XML segments file, to be downloaded from a remote server. See the chapter 'Automatic Update Facility' for supported URL options. Access: Instant. AC INI-Param: APSSegmentsFileUrl
acSysId	1.3.6.1.4.1.5003.9.10.10.2.3
U32 acSysIdFirstSerialNumber	1.3.6.1.4.1.5003.9.10.10.2.3.4	Unsigned32	read-only	The device's first serial number. When the device is part of a dual module board this is the first module's serial number. When the device is the first module in a dual module or the device is not in a dual module board, the values for asSysIdSerialNumber and acSysIdFirstSerialNumber are the same. AC INI-Param: N/A
STR acSysIdName	1.3.6.1.4.1.5003.9.10.10.2.3.1	SnmpAdminString	read-only	The name fo the board. AC INI-Param: N/A
U32 acSysIdSerialNumber	1.3.6.1.4.1.5003.9.10.10.2.3.2	Unsigned32	read-only	serial number of board. AC INI-Param: N/A
U32 acSysIdSlotNumber	1.3.6.1.4.1.5003.9.10.10.2.3.3	Unsigned32	read-only	Slot number. AC INI-Param: N/A
acSysIKE	1.3.6.1.4.1.5003.9.10.10.1.7.21
INT acSysIKEPolicyAction	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.3	INTEGER	read-create	This parameter is used for the Internet Key Encryption (IKE) Mangement Field for ACTIONS. Internal parameter. AC INI-Param: IKE_DB_ACTION
INT acSysIKEPolicyActionRes	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.4	INTEGER	read-only	This parameter is used for the Internet Key Encryption (IKE) Mangement Field for ACTIONS RESULT. Internal parameter. AC INI-Param: IKE_DB_ACTION_RESULT
INT acSysIKEPolicyAuthenticationMethod	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.20	INTEGER	read-create	This parameter is used for Internet Key Encryption (IKE) Policy - IKE Authentication Method (Preshared key/ RSA). Access: Offline. AC INI-Param: IKEPOLICYAUTHENTICATIONMETHOD
acSysIKEPolicyEntry	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1		not-accessible
U32 acSysIKEPolicyIndex	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.1	Unsigned32	not-accessible	This parameter is used for the Internet Key Encryption (IKE) Index Field for line. Internal parameter. AC INI-Param: IKE_DB_INDEX
U32 acSysIKEPolicyLifeInKB	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.7	Unsigned32	read-create	IKE Policy - IKE SA LifeTime in KB. Access: Instant. AC INI-Param: IKEPOLICYLIFEINKB
U32 acSysIKEPolicyLifeInSeconds	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.6	Unsigned32	read-create	IKE Policy - IKE SA LifeTime in seconds. Access: Instant. AC INI-Param: IKEPOLICYLIFEINSEC
INT acSysIKEPolicyProposal0Authentication	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.12	INTEGER	read-create	IKE Policy - Proposal 0 authentication type. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALAUTHENTICATION_0
INT acSysIKEPolicyProposal0DHGroup	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.16	INTEGER	read-create	IKE Policy - Proposal 0 Diffie Hellman Group. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALDHGROUP_0
INT acSysIKEPolicyProposal0Encryption	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.8	INTEGER	read-create	IKE Policy - Proposal 0 encryption type. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALENCRYPTION_0
INT acSysIKEPolicyProposal1Authentication	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.13	INTEGER	read-create	IKE Policy - Proposal 1 authentication type. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALAUTHENTICATION_1
INT acSysIKEPolicyProposal1DHGroup	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.17	INTEGER	read-create	IKE Policy - Proposal 1 Diffie Hellman Group. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALDHGROUP_1
INT acSysIKEPolicyProposal1Encryption	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.9	INTEGER	read-create	IKE Policy - Proposal 1 encryption type. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALENCRYPTION_1
INT acSysIKEPolicyProposal2Authentication	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.14	INTEGER	read-create	IKE Policy - Proposal 2 authentication type. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALAUTHENTICATION_2
INT acSysIKEPolicyProposal2DHGroup	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.18	INTEGER	read-create	IKE Policy - Proposal 2 Diffie Hellman Group. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALDHGROUP_2
INT acSysIKEPolicyProposal2Encryption	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.10	INTEGER	read-create	IKE Policy - Proposal 2 encryption type. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALENCRYPTION_2
INT acSysIKEPolicyProposal3Authentication	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.15	INTEGER	read-create	IKE Policy - Proposal 3 authentication type. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALAUTHENTICATION_3
INT acSysIKEPolicyProposal3DHGroup	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.19	INTEGER	read-create	IKE Policy - Proposal 3 Diffie Hellman Group. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALDHGROUP_3
INT acSysIKEPolicyProposal3Encryption	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.11	INTEGER	read-create	IKE Policy - Proposal 3 encryption type. Access: Instant. AC INI-Param: IKEPOLICYPROPOSALENCRYPTION_3
ROW acSysIKEPolicyRowStatus	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.2	RowStatus	read-create	This parameter is used for the Internet Key Encryption (IKE) ROWSTATUS Field for line. Internal parameter. AC INI-Param: IKE_DB_ROWSTATUS
STR acSysIKEPolicyShardKey	1.3.6.1.4.1.5003.9.10.10.1.7.21.1.1.5	SnmpAdminString	read-create	IKE Policy - Shared Key. Access: Instant. AC INI-Param: IKEPOLICYSHAREDKEY
acSysIKEPolicyTable	1.3.6.1.4.1.5003.9.10.10.1.7.21.1		not-accessible
INT acSysInterfaceAction	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.3	INTEGER	read-create	Mangement Field for ACTIONS. AC INI-Param: InterfaceTable_Action
INT acSysInterfaceActionRes	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.4	INTEGER	read-only	Mangement Field for ACTIONS RESULT. AC INI-Param: InterfaceTable_ActionRes
INT acSysInterfaceApplicationTypes	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.5	INTEGER	read-create	The type assigned to the interface. Access: Offline. AC INI-Param: InterfaceTable_ApplicationTypes
acSysInterfaceEntry	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1		not-accessible
STR acSysInterfaceGateway	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.9	SnmpAdminString	read-create	Default Gateway. Filled in one row only. 0 in others. Access: Offline. AC INI-Param: InterfaceTable_Gateway
U32 acSysInterfaceIndex	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.1	Unsigned32	not-accessible	Index Field for line. AC INI-Param: InterfaceTable_Index
STR acSysInterfaceIPAddress	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.7	SnmpAdminString	read-create	IP Address (can be either IPv4 or IPv6) for this interface. Access: Online. AC INI-Param: InterfaceTable_IPAddress
INT acSysInterfaceMode	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.6	INTEGER	read-create	Interface configuration mode. Access: Offline. AC INI-Param: InterfaceTable_InterfaceMode
STR acSysInterfaceName	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.11	SnmpAdminString	read-create	a 16 character string of this interface�s name. Access: Offline. AC INI-Param: InterfaceTable_InterfaceName
U32 acSysInterfacePrefixLength	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.8	Unsigned32	read-create	The number of �1� bits in this interface�s netmask. Access: Offline. AC INI-Param: InterfaceTable_PrefixLength
ROW acSysInterfaceRowStatus	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.2	RowStatus	read-create	ROWSTATUS Field for line. AC INI-Param: InterfaceTable_RowStatus
INT acSysInterfaceStatusApplicationTypes	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.3	INTEGER	read-only	The type assigned to the interface. AC INI-Param: N/A
acSysInterfaceStatusEntry	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1		not-accessible
U32 acSysInterfaceStatusEntryIndex	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.1	Unsigned32	not-accessible	Related Interface index in the interface configuration table (in case the table is empty - meaning there is only single IP the index will appear with 0). AC INI-Param: N/A
STR acSysInterfaceStatusGateway	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.7	SnmpAdminString	read-only	Default Gateway. AC INI-Param: N/A
STR acSysInterfaceStatusIPAddress	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.5	SnmpAdminString	read-only	IP Address (can be either IPv4 or IPv6) for this interface. AC INI-Param: N/A
INT acSysInterfaceStatusMode	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.4	INTEGER	read-only	Interface configuration mode. AC INI-Param: N/A
STR acSysInterfaceStatusName	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.9	SnmpAdminString	read-only	16 character string of this interface�s name. AC INI-Param: N/A
U32 acSysInterfaceStatusPrefixLength	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.6	Unsigned32	read-only	The number of �1� bits in this interface�s netmask. AC INI-Param: N/A
acSysInterfaceStatusTable	1.3.6.1.4.1.5003.9.10.10.2.6.4.21		not-accessible
U32 acSysInterfaceStatusTypeIndex	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.2	Unsigned32	not-accessible	1 - IP Address. 2 - IPv6 Link-Local Address. AC INI-Param: N/A
U32 acSysInterfaceStatusVlanID	1.3.6.1.4.1.5003.9.10.10.2.6.4.21.1.8	Unsigned32	read-only	VLAN ID of this interface. AC INI-Param: N/A
acSysInterfaceTable	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22		not-accessible	Multiple Interfaces' Interface Table
U32 acSysInterfaceVlanID	1.3.6.1.4.1.5003.9.10.10.1.3.1.30.22.1.10	Unsigned32	read-create	VLAN ID of this interface. Access: Offline. AC INI-Param: InterfaceTable_VlanID
acSysIP	1.3.6.1.4.1.5003.9.10.10.1.3.1
IP acSysIPAddress	1.3.6.1.4.1.5003.9.10.10.1.3.1.1	IpAddress	read-write	Board IP Address. In human readable form. in host byte order e.g. 192.10.1.2 = 0xc00a0102). Users should set the subnet mask to a valid value per the IP address. Access: Online. AC INI-Param: N/A
IP acSysIPDefaultGatewayAddress	1.3.6.1.4.1.5003.9.10.10.1.3.1.3	IpAddress	read-write	Default Gateway Address. Board's Default Gateway IP address. In human readable form. (in host byte order e.g. 192.10.1.255 = 0xc00a01ff). Access: Online. AC INI-Param: N/A
INT acSysIPDHCPEnable	1.3.6.1.4.1.5003.9.10.10.1.3.1.4	INTEGER	read-write	Enables/disables DHCP support. 0 = Disable 1 = Enable After the gateway is powered up, it attempts to communicate with a BootP server. If a BootP server does not respond and if DHCP is enabled, the gateway attempts to obtain its IP address and other network parameters from the DHCP server. Note that throughout the DHCP procedure, the BootP/TFTP application must be deactivated. If it isn�t deactivated, the gateway receives a response from the BootP server instead of the DHCP server. For additional information on DHCP, refer to the product documentation. Note: DHCPEnable is a special �Hidden� parameter. Once defined and saved in flash memory, its assigned value doesn�t revert to its default even if the parameter doesn't appear in the INI file. Access: Online. AC INI-Param: DHCPEnable
INT acSysIPDHCPLeaseRenewalEnable	1.3.6.1.4.1.5003.9.10.10.1.3.1.10	INTEGER	read-write	Enables/disables DHCP renewal support. This paramater will only take effect if DHCPEnable = 0. After the gateway is powered up, it attempts to communicate with a BootP server. If a BootP server does not respond and if DHCP is disabled, the gateway will boot from flash. It will then attempt to communicate with the DHCP server to renew the lease. Note that throughout the DHCP procedure, the BootP/TFTP application must be deactivated. If it isn�t deactivated, the gateway receives a response from the BootP server instead of the DHCP server. For additional information on DHCP, refer to the product documentation. For cases where the booting the board via DHCP is not desirable, but renewing DHCP leasing is. if DHCPEnable = 1, this paramater will not have any effect. Access: Online. AC INI-Param: EnableDHCPLeaseRenewal
U32 acSysIPDHCPSpeedFactor	1.3.6.1.4.1.5003.9.10.10.1.3.1.5	Unsigned32	read-write	Controls the DHCP renewal speed. When set to 0, the DHCP lease renewal is disabled. Otherwise, the renewal time is divided by this factor. Some DHCP-enabled routers perform better when set to 4. 0 = Disable DHCP 1 = Normal 2 to 10 = Fast. Access: Offline. AC INI-Param: DHCPSpeedFactor
IP acSysIPDnsPrimaryServer	1.3.6.1.4.1.5003.9.10.10.1.3.1.7	InetAddress	read-write	This parameter defines the DNS primary server's IP address. Range = Legal IP address. Access: Offline. AC INI-Param: DNSPriServerIP
INT acSysIPDnsPrimaryServerType	1.3.6.1.4.1.5003.9.10.10.1.3.1.6	INTEGER	read-write	This parameter defines the DNS primary server's IP address type. Access: Offline. AC INI-Param: N/A
IP acSysIPDnsSecondaryServer	1.3.6.1.4.1.5003.9.10.10.1.3.1.9	InetAddress	read-write	This parameter defines the DNS secondary server's IP address. Range = Legal IP address. Access: Offline. AC INI-Param: DNSSecServerIP
INT acSysIPDnsSecondaryServerType	1.3.6.1.4.1.5003.9.10.10.1.3.1.8	INTEGER	read-write	This parameter defines the DNS secondary server's IP address type. Access: Offline. AC INI-Param: N/A
acSysIPSec	1.3.6.1.4.1.5003.9.10.10.1.7.22
INT acSysIPSecDpdMode	1.3.6.1.4.1.5003.9.10.10.1.7.22.2	INTEGER	read-write	IPsec Dead Peer Detection (RFC 3706) - Mode of Operation. One of the following values: '0' - Disabled (Default) '1' - Periodic '2' - On demand. Access: Instant. AC INI-Param: IPSECDPDMODE
INT acSysIPSecEnable	1.3.6.1.4.1.5003.9.10.10.1.7.22.1	INTEGER	read-write	IPsec Enable flag. Access: Offline. AC INI-Param: ENABLEIPSEC
INT acSysIPSecIKECertificateExtValidate	1.3.6.1.4.1.5003.9.10.10.1.7.22.3	INTEGER	read-write	Enables or disables certificate extension checking for IKE. Access: Instant. AC INI-Param: IKEcertificateExtValidate
INT acSysIPsecProposalAction	1.3.6.1.4.1.5003.9.10.10.1.7.22.22.1.3	INTEGER	read-create	Mangement Field for ACTIONS. AC INI-Param: IPsecProposalTable_Action
INT acSysIPsecProposalActionRes	1.3.6.1.4.1.5003.9.10.10.1.7.22.22.1.4	INTEGER	read-only	Mangement Field for ACTIONS RESULT. AC INI-Param: IPsecProposalTable_ActionRes
INT acSysIPsecProposalAuthenticationAlgorithm	1.3.6.1.4.1.5003.9.10.10.1.7.22.22.1.6	INTEGER	read-create	Selects the message authentication (integrity) algorithm to use. Access: Online. AC INI-Param: IPsecProposalTable_AuthenticationAlgorithm
INT acSysIPsecProposalDiffieHellmanGroup	1.3.6.1.4.1.5003.9.10.10.1.7.22.22.1.7	INTEGER	read-create	Selects the Diffie-Hellman group to use. Access: Online. AC INI-Param: IPsecProposalTable_DHGroup
INT acSysIPsecProposalEncryptionAlgorithm	1.3.6.1.4.1.5003.9.10.10.1.7.22.22.1.5	INTEGER	read-create	Selects the encryption (privacy) algorithm to use. Access: Online. AC INI-Param: IPsecProposalTable_EncryptionAlgorithm
acSysIPsecProposalEntry	1.3.6.1.4.1.5003.9.10.10.1.7.22.22.1		not-accessible
U32 acSysIPsecProposalIndex	1.3.6.1.4.1.5003.9.10.10.1.7.22.22.1.1	Unsigned32	not-accessible	Index Field for line. AC INI-Param: IPsecProposalTable_Index
ROW acSysIPsecProposalRowStatus	1.3.6.1.4.1.5003.9.10.10.1.7.22.22.1.2	RowStatus	read-create	ROWSTATUS Field for line. AC INI-Param: IPsecProposalTable_RowStatus
acSysIPsecProposalTable	1.3.6.1.4.1.5003.9.10.10.1.7.22.22		not-accessible	IPsec Proposal table
U32 acSysIPsecSAAction	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.3	Unsigned32	read-create	Mangement Field for ACTIONS. AC INI-Param: IPsecSATable_Action
U32 acSysIPsecSAActionRes	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.4	Unsigned32	read-only	Mangement Field for ACTIONS RESULT. AC INI-Param: IPsecSATable_ActionRes
INT acSysIPsecSAAuthenticationMethod	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.6	INTEGER	read-create	Selects the method used for peer authentication during IKE main mode. Access: Online. AC INI-Param: IPsecSATable_AuthenticationMethod
U32 acSysIPsecSADestPort	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.9	Unsigned32	read-create	Defines the destination port to which this configuration applies. Access: Online. AC INI-Param: IPsecSATable_DestPort
INT acSysIPsecSADPDmode	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.14	INTEGER	read-create	Controls dead peer detection (DPD) as per RFC 3706. Access: Online. AC INI-Param: IPsecSATable_DPDmode
acSysIPsecSAEntry	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1		not-accessible
U32 acSysIPsecSAIndex	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.1	Unsigned32	not-accessible	Index Field for line. AC INI-Param: IPsecSATable_Index
INT acSysIPsecSAIPsecMode	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.15	INTEGER	read-create	Selects the IPSec mode of operation. 0 = Transport mode (default) 1 = Tunnel mode . Access: Online. AC INI-Param: IPsecSATable_IPsecMode
U32 acSysIPsecSAPhase1SaLifetimeInSec	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.11	Unsigned32	read-create	Determines the duration (in seconds) for which the negotiated IKE SA (main mode) is valid. After the time expires, the SA is re-negotiated. Access: Online. AC INI-Param: IPsecSATable_Phase1SaLifetimeInSec
U32 acSysIPsecSAPhase2SaLifetimeInKB	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.13	Unsigned32	read-create	Determines the maximum volume of traffic (in kilobytes) for which the negotiated IPSec SA (quick mode) is valid. Access: Online. AC INI-Param: IPsecSATable_Phase2SaLifetimeInKB
U32 acSysIPsecSAPhase2SaLifetimeInSec	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.12	Unsigned32	read-create	Determines the duration (in seconds) for which the negotiated IPSec SA (quick mode) is valid. After the time expires, the SA is re-negotiated. Access: Online. AC INI-Param: IPsecSATable_Phase2SaLifetimeInSec
U32 acSysIPsecSAProtocol	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.10	Unsigned32	read-create	Defines the protocol type to which this configuration applies. Standard IP protocol numbers should be used, e.g.: 0 = Any protocol (default) 17 = UDP 6 = TCP . Access: Online. AC INI-Param: IPsecSATable_Protocol
STR acSysIPsecSARemoteEndpointAddress	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.5	SnmpAdminString	read-create	IP address or DNS host name of the peer. Access: Online. AC INI-Param: IPsecSATable_RemoteEndpointAddressOrName
STR acSysIPsecSARemoteSubnetIPAddress	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.17	SnmpAdminString	read-create	IP address of the remote subnetwork. Access: Online. AC INI-Param: IPsecSATable_RemoteSubnetIPAddress
U32 acSysIPsecSARemoteSubnetPrefixLength	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.18	Unsigned32	read-create	Prefix length of the Remote Subnet IP Address parameter (in bits). Access: Online. AC INI-Param: IPsecSATable_RemoteSubnetPrefixLength
STR acSysIPsecSARemoteTunnelAddress	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.16	SnmpAdminString	read-create	IP address of the peer router. Access: Online. AC INI-Param: IPsecSATable_RemoteTunnelAddress
ROW acSysIPsecSARowStatus	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.2	RowStatus	read-create	ROWSTATUS Field for line. AC INI-Param: IPsecSATable_RowStatus
STR acSysIPsecSASharedKey	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.7	SnmpAdminString	read-create	Defines the pre-shared key (in textual format). Access: Online. AC INI-Param: IPsecSATable_SharedKey
U32 acSysIPsecSASourcePort	1.3.6.1.4.1.5003.9.10.10.1.7.22.23.1.8	Unsigned32	read-create	Defines the source port to which this configuration applies. Access: Online. AC INI-Param: IPsecSATable_SourcePort
acSysIPsecSATable	1.3.6.1.4.1.5003.9.10.10.1.7.22.23		not-accessible	IPsec SA table
INT acSysIPSecSPDAction	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.3	INTEGER	read-create	Security Policy Database (SPD) Mangement Field for ACTIONS. Internal parameter. AC INI-Param: SPD_ACTION
INT acSysIPSecSPDActionRes	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.4	INTEGER	read-only	Security Policy Database (SPD) Mangement Field for ACTIONS RESULT. Internal parameter. AC INI-Param: SPD_ACTION_RESULT
acSysIPSecSPDEntry	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1		not-accessible
U32 acSysIPSecSPDIndex	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.1	Unsigned32	not-accessible	Security Policy Database (SPD) Index Field for line. Internal parameter. AC INI-Param: SPD_INDEX
U32 acSysIPSecSPDKeyExchangeMethodIndex	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.9	Unsigned32	read-create	This parameter is used for the Secure Internet Protocol (IPsec) Policy - Index into the Key Exchange Method Table (IKE Table). Access: Offline. AC INI-Param: IPSECPOLICYKEYEXCHANGEMETHODINDEX
U32 acSysIPSecSPDLifeInKB	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.11	Unsigned32	read-create	IPsec Policy - IPSec SA LifeTime in KB. Access: Instant. AC INI-Param: IPSECPOLICYLIFEINKB
U32 acSysIPSecSPDLifeInSeconds	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.10	Unsigned32	read-create	IPsec Policy - IPSec SA LifeTime in seconds. Access: Instant. AC INI-Param: IPSECPOLICYLIFEINSEC
INT acSysIPSecSPDMode	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.21	INTEGER	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy - Mode of Operation (Transport/Tunneling). '0' - Transport '1' - Tunneling. Access: Instant. AC INI-Param: IPSECMODE
U32 acSysIPSecSPDPolicyDestPort	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.7	Unsigned32	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy Policy - Destination Port. Access: Instant. AC INI-Param: IPSECPOLICYDSTPORT
INT acSysIPSecSPDPolicyLocalIPAddrType	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.20	INTEGER	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy - Local IP address type (OAM/Control). Access: Offline. AC INI-Param: IPSECPOLICYLOCALIPADDRESSTYPE
IP acSysIPSecSPDPolicyLocalTunnelIPAddress	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.23	IpAddress	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy - IP Address of the Remote IPSec Tunnel Endpoint. Access: Instant. AC INI-Param: IPSECPOLICYLOCALTUNNELIPADDRESS
U32 acSysIPSecSPDPolicyProtocol	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.8	Unsigned32	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy Policy - Protocol. Access: Instant. AC INI-Param: IPSECPOLICYPROTOCOL
STR acSysIPSecSPDPolicyRemoteIPAddr	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.5	SnmpAdminString	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy Policy - Remote IP address as IP or Host Name. Access: Instant. AC INI-Param: IPSECPOLICYREMOTEIPADDRESS
IP acSysIPSecSPDPolicyRemoteTunnelIPAddress	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.22	IpAddress	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy - IP Address of the Remote IPSec Tunnel Endpoint. Access: Instant. AC INI-Param: IPSECPOLICYREMOTETUNNELIPADDRESS
IP acSysIPSecSPDPolicyRemoteTunnelSubnetMask	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.24	IpAddress	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy - Subnet Mask of the Remote IPSec Address. Access: Instant. AC INI-Param: IPSECPOLICYREMOTESUBNETMASK
U32 acSysIPSecSPDPolicySrcPort	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.6	Unsigned32	read-create	This parameter is used for Secure Internet Protocol (IPsec) Policy Policy - Source Port. Access: Instant. AC INI-Param: IPSECPOLICYSRCPORT
INT acSysIPSecSPDProposal0Authentication	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.16	INTEGER	read-create	IPsec Policy - Proposal 0 authentication type. Access: Instant. AC INI-Param: IPSECPOLICYPROPOSALAUTHENTICATION_0
INT acSysIPSecSPDProposal0Encryption	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.12	INTEGER	read-create	IPsec Policy - Proposal 0 encryption type. Access: Instant. AC INI-Param: IPSECPOLICYPROPOSALENCRYPTION_0
INT acSysIPSecSPDProposal1Authentication	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.17	INTEGER	read-create	IPsec Policy - Proposal 0 authentication type. Access: Instant. AC INI-Param: IPSECPOLICYPROPOSALAUTHENTICATION_1
INT acSysIPSecSPDProposal1Encryption	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.13	INTEGER	read-create	IPsec Policy - Proposal 1 encryption type. Access: Instant. AC INI-Param: IPSECPOLICYPROPOSALENCRYPTION_1
INT acSysIPSecSPDProposal2Authentication	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.18	INTEGER	read-create	IPsec Policy - Proposal 0 authentication type. Access: Instant. AC INI-Param: IPSECPOLICYPROPOSALAUTHENTICATION_2
INT acSysIPSecSPDProposal2Encryption	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.14	INTEGER	read-create	IPsec Policy - Proposal 2 encryption type. Access: Instant. AC INI-Param: IPSECPOLICYPROPOSALENCRYPTION_2
INT acSysIPSecSPDProposal3Authentication	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.19	INTEGER	read-create	IPsec Policy - Proposal 0 authentication type. Access: Instant. AC INI-Param: IPSECPOLICYPROPOSALAUTHENTICATION_3
INT acSysIPSecSPDProposal3Encryption	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.15	INTEGER	read-create	IPsec Policy - Proposal 3 encryption type. Access: Instant. AC INI-Param: IPSECPOLICYPROPOSALENCRYPTION_3
ROW acSysIPSecSPDRowStatus	1.3.6.1.4.1.5003.9.10.10.1.7.22.21.1.2	RowStatus	read-create	Security Policy Database (SPD) ROWSTATUS field for line. Internal parameter. AC INI-Param: SPD_ROWSTATUS
acSysIPSecSPDTable	1.3.6.1.4.1.5003.9.10.10.1.7.22.21		not-accessible
acSysIPStatus	1.3.6.1.4.1.5003.9.10.10.2.6.4
IP acSysIPSubNetAddress	1.3.6.1.4.1.5003.9.10.10.1.3.1.2	IpAddress	read-write	Board SubNet Address. In human readable form. (in host byte order e.g. 255.255.255.0 = 0xffffff00). default =255.255.255.0. Access: Online. AC INI-Param: N/A
acSysLDAP	1.3.6.1.4.1.5003.9.10.10.1.15
STR acSysLDAPBindDN	1.3.6.1.4.1.5003.9.10.10.1.15.7	SnmpAdminString	read-write	This parameter is used to indicate the of LDAP server bind DN. Access: Online. AC INI-Param: LDAPBINDDN
STR acSysLDAPPassword	1.3.6.1.4.1.5003.9.10.10.1.15.6	SnmpAdminString	read-write	This parameter is used to indicate the user password of LDAP server. Access: Online. AC INI-Param: LDAPPASSWORD
STR acSysLDAPSearchDN	1.3.6.1.4.1.5003.9.10.10.1.15.5	SnmpAdminString	read-write	This parameter is used to indicate the search DN for LDAP search request. Access: Online. AC INI-Param: LDAPSEARCHDN
STR acSysLDAPServerDomainName	1.3.6.1.4.1.5003.9.10.10.1.15.4	SnmpAdminString	read-write	This parameter is used to indicate the name of LDAP server. Access: Online. AC INI-Param: LDAPSERVERDOMAINNAME
IP acSysLDAPServerIp	1.3.6.1.4.1.5003.9.10.10.1.15.1	IpAddress	read-write	This parameter defines the IP address in dotted format notation. e.g., 192.10.1.255 Range = Legal IP address. Access: Online. AC INI-Param: LDAPSERVERIP
U32 acSysLDAPServerMaxRespondTime	1.3.6.1.4.1.5003.9.10.10.1.15.3	Unsigned32	read-write	Defines the period of time the module will wait for LDAP server response (seconds). Access: Online. AC INI-Param: LDAPSERVERMAXRESPONDTIME
U32 acSysLDAPServerPort	1.3.6.1.4.1.5003.9.10.10.1.15.2	Unsigned32	read-write	Defines the port number for the LDAP server. Range = Valid port number. Access: Online. AC INI-Param: LDAPSERVERPORT
INT acSysLDAPServiceEnable	1.3.6.1.4.1.5003.9.10.10.1.15.8	INTEGER	read-write	Used to either enable or disable LDAP service. 0- disable (default) 1 - enable. Access: Offline. AC INI-Param: LDAPSERVICEENABLE
acSysLDAPStatus	1.3.6.1.4.1.5003.9.10.10.2.11
INT acSysLDAPStatusServerMode	1.3.6.1.4.1.5003.9.10.10.2.11.1	INTEGER	read-only	LDAP server status. AC INI-Param: N/A
acSysLicenseKey	1.3.6.1.4.1.5003.9.10.10.1.5
STR acSysLicenseKeyActiveList	1.3.6.1.4.1.5003.9.10.10.1.5.2	SnmpAdminString	read-only	List of all avtivated features. AC INI-Param: N/A
STR acSysLicenseKeyString	1.3.6.1.4.1.5003.9.10.10.1.5.1	SnmpAdminString	read-write	Coded Key specific for board and required features. Access: Offline. AC INI-Param: N/A
acSyslog	1.3.6.1.4.1.5003.9.10.10.1.3.2
U32 acSyslogAcSyslogServerPortNumber	1.3.6.1.4.1.5003.9.10.10.1.3.2.3	Unsigned32	read-write	Defines the Port number of the Syslog Server. Range = Legal Port Number. Access: Instant. AC INI-Param: SyslogServerPort
INT acSyslogEnable	1.3.6.1.4.1.5003.9.10.10.1.3.2.2	INTEGER	read-write	Enable SysLog protocol log. Access: Online. AC INI-Param: ENABLESYSLOG
IP acSyslogServerIPAddress	1.3.6.1.4.1.5003.9.10.10.1.3.2.1	IpAddress	read-write	This parameter defines the IP address in dotted format notation. e.g., 192.10.1.255 Range = Legal IP address. Access: Instant. AC INI-Param: SYSLOGSERVERIP
acSysMediaEncription	1.3.6.1.4.1.5003.9.10.10.1.7.24
INT acSysMediaEncriptionRTCPEncryptionDisableRx	1.3.6.1.4.1.5003.9.10.10.1.7.24.6	INTEGER	read-write	On a secured RTP session, determines whether to enable Encryption on received RTCP packets. One of the following values: 0 = Enable 1 = Disable. Access: Online. AC INI-Param: RTCPEncryptionDisableRx
INT acSysMediaEncriptionRTCPEncryptionDisableTx	1.3.6.1.4.1.5003.9.10.10.1.7.24.5	INTEGER	read-write	On a secured RTP session, determines whether to enable Encryption on transmitted RTCP packets. One of the following values: 0 = Enable 1 = Disable. Access: Online. AC INI-Param: RTCPEncryptionDisableTx
INT acSysMediaEncriptionRTPAuthenticationDisableRx	1.3.6.1.4.1.5003.9.10.10.1.7.24.2	INTEGER	read-write	On a secured RTP session, determines whether to enable Authentication on received RTP packets 0 = Enable 1 = Disable. Access: Online. AC INI-Param: RTPAuthenticationDisableRx
INT acSysMediaEncriptionRTPAuthenticationDisableTx	1.3.6.1.4.1.5003.9.10.10.1.7.24.1	INTEGER	read-write	On a secured RTP session, determines whether to enable Authentication on transmitted RTP packets. One of the following values: 0 = Enable 1 = Disable. Access: Online. AC INI-Param: RTPAuthenticationDisableTx
INT acSysMediaEncriptionRTPEncryptionDisableRx	1.3.6.1.4.1.5003.9.10.10.1.7.24.4	INTEGER	read-write	On a secured RTP session, determines whether to enable Encryption on transmitted RTP packets. One of the following values: 0 = Enable 1 = Disable. Access: Online. AC INI-Param: RTPEncryptionDisableRx
INT acSysMediaEncriptionRTPEncryptionDisableTx	1.3.6.1.4.1.5003.9.10.10.1.7.24.3	INTEGER	read-write	On a secured RTP session, determines whether to enable Encryption on transmitted RTP packets. One of the following values: 0 = Enable 1 = Disable. Access: Online. AC INI-Param: RTPEncryptionDisableTx
acSysMiscConfig	1.3.6.1.4.1.5003.9.10.10.1.4
INT acSysModuleActions	1.3.6.1.4.1.5003.9.10.10.4.21.1.12	INTEGER	read-write	Actions to be performed by the module. Access: Instant. AC INI-Param: N/A
acSysModuleEntry	1.3.6.1.4.1.5003.9.10.10.4.21.1		not-accessible
U32 acSysModuleFirstPortNum	1.3.6.1.4.1.5003.9.10.10.4.21.1.16	Unsigned32	read-only	The logical number as seen in the general trunk/analog-channel table of the first port in the module in question. Since analog and digital ports can be operational at once, analog and digital ports may have same logical number. AC INI-Param: N/A
INT acSysModuleFRUaction	1.3.6.1.4.1.5003.9.10.10.4.21.1.13	INTEGER	read-write	Field Replace Unit actions Relevant to IF-Module only. Access: Instant. AC INI-Param: N/A
INT acSysModuleFRUstatus	1.3.6.1.4.1.5003.9.10.10.4.21.1.14	INTEGER	read-only	Field Replace Unit module's status. AC INI-Param: N/A
U32 acSysModuleGeographicalPosition	1.3.6.1.4.1.5003.9.10.10.4.21.1.2	Unsigned32	read-only	The slot number in the chassis. 1 being the bottom slot and so on. AC INI-Param: N/A
INT acSysModuleHAStatus	1.3.6.1.4.1.5003.9.10.10.4.21.1.9	INTEGER	read-only	Modules status with in the system. Designed to define the HA state. AC INI-Param: N/A
U32 acSysModuleIndex	1.3.6.1.4.1.5003.9.10.10.4.21.1.1	Unsigned32	not-accessible	The Module number in the system. AC INI-Param: N/A
OCT acSysModuleLEDs	1.3.6.1.4.1.5003.9.10.10.4.21.1.10	OCTET STRING	read-only	Bit Field for the LEDs on the front of the module. LSB in each nibble (half Byte) is 0 - constant, 1 - blinking. 3 MSB are the color - 0 - none 1- Green 2 - Red 3 - Yellow 4 - Orange 5 - Blue 7 - Gray (unknown). AC INI-Param: N/A
STR acSysModuleLicenseKeyList	1.3.6.1.4.1.5003.9.10.10.4.21.1.5	SnmpAdminString	read-only	List of active features as enabled by the license key. SA modules return NULL. AC INI-Param: N/A
U32 acSysModuleNumOfPorts	1.3.6.1.4.1.5003.9.10.10.4.21.1.15	Unsigned32	read-only	The number of physical interfaces in a module, analog or digital. AC INI-Param: N/A
INT acSysModuleOperationalState	1.3.6.1.4.1.5003.9.10.10.4.21.1.8	INTEGER	read-only	The operational state of the module. Determined internally by the system. AC INI-Param: N/A
INT acSysModulePresence	1.3.6.1.4.1.5003.9.10.10.4.21.1.4	INTEGER	read-only	Is the module present or missing. AC INI-Param: N/A
I32 acSysModuleSerialNumber	1.3.6.1.4.1.5003.9.10.10.4.21.1.6	Integer32	read-only	The module's serial number. For 6310 the serial number is the decimal form of the last 5 characters in the MAC Address. SA modules return 0. When the modules in the table are unavailable for audit (no HA) (-1) is returned. AC INI-Param: N/A
STR acSysModuleSWVersion	1.3.6.1.4.1.5003.9.10.10.4.21.1.7	SnmpAdminString	read-only	The version of the SW being run in the module placed . SA Modules return NULL. AC INI-Param: N/A
acSysModuleTable	1.3.6.1.4.1.5003.9.10.10.4.21		not-accessible
I32 acSysModuleTemperature	1.3.6.1.4.1.5003.9.10.10.4.21.1.11	Integer32	read-only	Temperature of the board in degrees Celsius. SA Modules return 0. AC INI-Param: N/A
INT acSysModuleType	1.3.6.1.4.1.5003.9.10.10.4.21.1.3	INTEGER	read-only	The module's type. AC INI-Param: N/A
acSysNAT	1.3.6.1.4.1.5003.9.10.10.2.6.2
acSysNATTraversal	1.3.6.1.4.1.5003.9.10.10.1.3.6
INT acSysNATType	1.3.6.1.4.1.5003.9.10.10.2.6.2.1	INTEGER	read-only	Identified NAT type. -1 - STUN client is disabled 0 - None 1 - FullCone 2 - Restricted 3 - PortRestricted 4 - Symmetric 5 - SymmetricFireWall 6 - Blocked 7 - Unknown 10 - NAT identification in progress. AC INI-Param: N/A
acSysNetwork	1.3.6.1.4.1.5003.9.10.10.2.6
acSysNetworkConfig	1.3.6.1.4.1.5003.9.10.10.1.3
acSysNetworkFileSystem	1.3.6.1.4.1.5003.9.10.10.1.11
INT acSysNFSAction	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.3	INTEGER	read-create	Mangement Field for ACTIONS. Internal parameter. AC INI-Param: N/A
INT acSysNFSActionRes	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.4	INTEGER	read-only	Mangement Field for ACTIONS RESULT. Internal parameter. AC INI-Param: N/A
INT acSysNFSAuthType	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.8	INTEGER	read-create	Identifies the authentication method used with this remote file system, 0 for AUTH_NULL, 1 for AUTH_UNIX (default). Access: Online. AC INI-Param: NFSServers_AuthType
acSysNFSEntry	1.3.6.1.4.1.5003.9.10.10.1.11.21.1		not-accessible
U32 acSysNFSGID	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.10	Unsigned32	read-create	Group ID used in authentication if using AUTH_UNIX. The default is 1. Access: Online. AC INI-Param: NFSServers_GID
STR acSysNFSHostOrIP	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.5	SnmpAdminString	read-create	The domain name or IP address of the NFS server. If a domain name is provided, then a DNS server must be configured. Access: Online. AC INI-Param: NFSServers_HostOrIP
U32 acSysNFSIndex	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.1	Unsigned32	not-accessible	Index Field for line. Internal parameter. AC INI-Param: NFSServers_Index
INT acSysNFSNfsVersion	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.7	INTEGER	read-create	NFS version to use with this remote file system, 2 or 3 (default). Access: Online. AC INI-Param: NFSServers_NfsVersion
STR acSysNFSRootPath	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.6	SnmpAdminString	read-create	Path to the root of the exported file system. Access: Online. AC INI-Param: NFSServers_RootPath
ROW acSysNFSRowStatus	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.2	RowStatus	read-create	ROWSTATUS field for line. Internal parameter. AC INI-Param: N/A
acSysNFSTable	1.3.6.1.4.1.5003.9.10.10.1.11.21		not-accessible
U32 acSysNFSUID	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.9	Unsigned32	read-create	User ID used in authentication if using AUTH_UNIX. The default is 0. Access: Online. AC INI-Param: NFSServers_UID
INT acSysNFSVlanType	1.3.6.1.4.1.5003.9.10.10.1.11.21.1.11	INTEGER	read-create	The VLAN, OAM(0) or Media(1), to use when accessing this remote file system. The default is to use the media VLAN. This parameters applies only if multiple IP addresses are configured on this board. Access: Online. AC INI-Param: NFSServers_VlanType
acSysNTP	1.3.6.1.4.1.5003.9.10.10.1.3.3
IP acSysNTPServerIPAddress	1.3.6.1.4.1.5003.9.10.10.1.3.3.1	IpAddress	read-write	This parameter is used to define the NTP server's IP address. Range = Legal IP address. Access: Instant. AC INI-Param: NTPServerIP
U32 acSysNTPUpdateInterval	1.3.6.1.4.1.5003.9.10.10.1.3.3.3	Unsigned32	read-write	This parameter defines the NTP update interval, in seconds. It's inadvisable to set it exceeding 1 month (2592000 seconds). Range = 0 to 2592000 seconds Default = 86400 seconds. Access: Instant. AC INI-Param: NTPUpdateInterval
I32 acSysNTPUtcOffset	1.3.6.1.4.1.5003.9.10.10.1.3.3.2	Integer32	read-write	This parameter is used to define the NTP time to offset, in seconds. Default = 0 Range = -43200 to +43200 seconds. Access: Instant. AC INI-Param: NTPServerUTCOffset
acSysPCM	1.3.6.1.4.1.5003.9.10.10.1.2.3
U32 acSysPCMIdleABCDPattern	1.3.6.1.4.1.5003.9.10.10.1.2.3.3	Unsigned32	read-write	Defines the ABCD (CAS) pattern to be applied on the signaling bus before it is changed by the user or the PSTN protocol. This is only relevant when using PSTN interface with CAS protocols. Range = 0x0 to 0xF. Access: Offline. AC INI-Param: IDLEABCDPATTERN
U32 acSysPCMIdlePattern	1.3.6.1.4.1.5003.9.10.10.1.2.3.2	Unsigned32	read-write	Defines the PCM pattern applied to the E1/T1 timeslot (B-channel) when the channel is idle. Default: 0xFF if PCMLawSelect is Mu-Law 0xD5 if PCMLawSelect is A-Law Range = 0x00 to 0xFF. Access: Offline. AC INI-Param: IDLEPCMPATTERN
INT acSysPCMLawSelect	1.3.6.1.4.1.5003.9.10.10.1.2.3.1	INTEGER	read-write	Selects the type of PCM companding law in input/output TDM bus (TDM bus is defined using the TDMBusType parameter). 1 = A-law 3 = Mu-Law. Access: Offline. AC INI-Param: PCMLAWSELECT
U32 acSysPCMSerialPortAuditIntervalMin	1.3.6.1.4.1.5003.9.10.10.1.2.3.4	Unsigned32	read-write	Interval timeout in minutes, of the Serial Port audit. In case of 0 value, the audit isn't running. Access: Offline. AC INI-Param: SerialPortAuditIntervalMin
INT acSysPEMElectricWireConnection	1.3.6.1.4.1.5003.9.10.10.4.24.1.5	INTEGER	read-only	Present the status of the electricity connector located on the PEM card. AC INI-Param: N/A
acSysPEMEntry	1.3.6.1.4.1.5003.9.10.10.4.24.1		not-accessible
INT acSysPEMExistence	1.3.6.1.4.1.5003.9.10.10.4.24.1.3	INTEGER	read-only	Is the PEM-Module present or missing. AC INI-Param: N/A
U32 acSysPEMGeographicalPosition	1.3.6.1.4.1.5003.9.10.10.4.24.1.2	Unsigned32	read-only	The slot number in the chassis. AC INI-Param: N/A
U32 acSysPEMIndex	1.3.6.1.4.1.5003.9.10.10.4.24.1.1	Unsigned32	not-accessible	PEM-Module's index in the system. AC INI-Param: N/A
acSysPEMTable	1.3.6.1.4.1.5003.9.10.10.4.24		not-accessible
STR acSysPEMType	1.3.6.1.4.1.5003.9.10.10.4.24.1.4	SnmpAdminString	read-only	PEM�s Type. AC INI-Param: N/A
acSysPLLStatusEntry	1.3.6.1.4.1.5003.9.10.10.4.26.21.1		not-accessible
U32 acSysPLLStatusIndex	1.3.6.1.4.1.5003.9.10.10.4.26.21.1.1	Unsigned32	not-accessible	Table's Index. AC INI-Param: N/A
INT acSysPLLStatusOperatingMode	1.3.6.1.4.1.5003.9.10.10.4.26.21.1.2	INTEGER	read-only	PLL's Current Operating Mode. AC INI-Param: N/A
acSysPLLStatusTable	1.3.6.1.4.1.5003.9.10.10.4.26.21		not-accessible
acSysPowerSupplyEntry	1.3.6.1.4.1.5003.9.10.10.4.23.1		not-accessible
INT acSysPowerSupplyExistence	1.3.6.1.4.1.5003.9.10.10.4.23.1.3	INTEGER	read-only	Is the Power-Supply present or missing. AC INI-Param: N/A
U32 acSysPowerSupplyGeographicalPosition	1.3.6.1.4.1.5003.9.10.10.4.23.1.2	Unsigned32	read-only	The slot number in the chassis. AC INI-Param: N/A
STR acSysPowerSupplyHwversion	1.3.6.1.4.1.5003.9.10.10.4.23.1.4	SnmpAdminString	read-only	PS�s HW version. AC INI-Param: N/A
U32 acSysPowerSupplyIndex	1.3.6.1.4.1.5003.9.10.10.4.23.1.1	Unsigned32	not-accessible	Power-Supply's index in the system. AC INI-Param: N/A
OCT acSysPowerSupplyLEDs	1.3.6.1.4.1.5003.9.10.10.4.23.1.5	OCTET STRING	read-only	A bit-field representation of the Power-Supply LEDs' status. The first four bites represent the Power-Supply LED's status and the last four bites represent the Fault LED's status. AC INI-Param: N/A
INT acSysPowerSupplySeverity	1.3.6.1.4.1.5003.9.10.10.4.23.1.6	INTEGER	read-only	The Severity of the power-supply according to the current active alarm in the alarm table. AC INI-Param: N/A
acSysPowerSupplyTable	1.3.6.1.4.1.5003.9.10.10.4.23		not-accessible
acSysRepositoryAMS	1.3.6.1.4.1.5003.9.10.10.2.9
INT acSysRepositoryAMSIsReadyForUpdate	1.3.6.1.4.1.5003.9.10.10.2.9.1	INTEGER	read-only	Verify if the old repository is free or there are signals still using it. AC INI-Param: N/A
acSysSATEntry	1.3.6.1.4.1.5003.9.10.10.4.25.21.1		not-accessible
acSysSATFramersEntry	1.3.6.1.4.1.5003.9.10.10.4.25.22.1		not-accessible
U32 acSysSATFramersFramerIndex	1.3.6.1.4.1.5003.9.10.10.4.25.22.1.2	Unsigned32	not-accessible	Framer's Index. AC INI-Param: N/A
INT acSysSATFramersFramerInterfaceStatus	1.3.6.1.4.1.5003.9.10.10.4.25.22.1.3	INTEGER	read-only	Framer Interface Status. AC INI-Param: N/A
INT acSysSATFramersFramerInterfaceType	1.3.6.1.4.1.5003.9.10.10.4.25.22.1.5	INTEGER	read-only	Framer Interface Type. AC INI-Param: N/A
INT acSysSATFramersFramerLoopBackRef	1.3.6.1.4.1.5003.9.10.10.4.25.22.1.4	INTEGER	read-only	Frame rLoop Back Reference. AC INI-Param: N/A
INT acSysSATFramersFramerTransmitControl	1.3.6.1.4.1.5003.9.10.10.4.25.22.1.6	INTEGER	read-only	Framer Transmit Control. AC INI-Param: N/A
INT acSysSATFramersIsUsedAsPLLClock	1.3.6.1.4.1.5003.9.10.10.4.25.22.1.8	INTEGER	read-only	Is Used As PLL Clock indication. AC INI-Param: N/A
INT acSysSATFramersRxStatus	1.3.6.1.4.1.5003.9.10.10.4.25.22.1.7	INTEGER	read-only	Provides the alarm status of the clock interface. AC INI-Param: N/A
U32 acSysSATFramersSatIndex	1.3.6.1.4.1.5003.9.10.10.4.25.22.1.1	Unsigned32	not-accessible	SAT-Module's index in the system. AC INI-Param: N/A
acSysSATFramersTable	1.3.6.1.4.1.5003.9.10.10.4.25.22		not-accessible
U32 acSysSATGeographicalPosition	1.3.6.1.4.1.5003.9.10.10.4.25.21.1.2	Unsigned32	read-only	The slot number in the chassis. AC INI-Param: N/A
INT acSysSATInitInformation	1.3.6.1.4.1.5003.9.10.10.4.25.21.1.4	INTEGER	read-only	Sat's Init Information. AC INI-Param: N/A
acSysSATModule	1.3.6.1.4.1.5003.9.10.10.4.25
U32 acSysSATSatIndex	1.3.6.1.4.1.5003.9.10.10.4.25.21.1.1	Unsigned32	not-accessible	SAT-Module's index in the system. AC INI-Param: N/A
acSysSATTable	1.3.6.1.4.1.5003.9.10.10.4.25.21		not-accessible
INT acSysSATTimingRefSelection	1.3.6.1.4.1.5003.9.10.10.4.25.21.1.6	INTEGER	read-only	SAT's Timing Reference Selection. AC INI-Param: N/A
INT acSysSATTimingUnitExistence	1.3.6.1.4.1.5003.9.10.10.4.25.21.1.5	INTEGER	read-only	Is the Timig Unit present or missing. AC INI-Param: N/A
STR acSysSATType	1.3.6.1.4.1.5003.9.10.10.4.25.21.1.3	SnmpAdminString	read-only	SAT�s Type. AC INI-Param: N/A
acSysSCTP	1.3.6.1.4.1.5003.9.10.10.1.3.11
U32 acSysSCTPAssociationsNum	1.3.6.1.4.1.5003.9.10.10.1.3.11.5	Unsigned32	read-write	Defines the maximum number of Stream Control Transmission Protocol (SCTP) associations that can be opened. Range: 1 to 8. Access: Offline. AC INI-Param: SCTPAssociationsNum
INT acSysSCTPCheckSumMethod	1.3.6.1.4.1.5003.9.10.10.1.3.11.3	INTEGER	read-write	Stream Control Transmission Protocol (SCTP) uses a checksum mechanism in order to authenticate packets on both sides (the receiving side and the transmitting side). Presently, two checksum mechanisms are available: 0 = adler32 checksum mechanism 1 = crc32c checksum mechanism (improved mechanism). Access: Offline. AC INI-Param: SCTPChecksumMethod
U32 acSysSCTPHeartBeatInterval	1.3.6.1.4.1.5003.9.10.10.1.3.11.1	Unsigned32	read-write	Defines the SCTP heartbeat interval. Range: 1 to 3600. Access: Offline. AC INI-Param: SCTPHBInterval
STR acSysSCTPHostName	1.3.6.1.4.1.5003.9.10.10.1.3.11.4	SnmpAdminString	read-write	When this parameter is set to any value other than an empty string, SCTP (Stream Control Transmission Protocol) uses the value as the value of the FQDN (Fully Qualified Domain Name) parameter attached to the INIT chunk. In this case, the FQDN parameter replaces any IP address parameters in the INIT chunk. This feature enables overcoming NAT problems where the original IP addresses belonging to the endpoint supports are converted into pseudo addresses. When this parameter is not set (default), the INIT chunk is sent without any FQDN parameter. Range = String[42]. Access: Offline. AC INI-Param: SCTPHOSTNAME
U32 acSysSCTPT4SACKTimer	1.3.6.1.4.1.5003.9.10.10.1.3.11.2	Unsigned32	read-write	Defines the SCTP T4 SACK timer interval. Range: 1 to 5. Access: Offline. AC INI-Param: SCTPT4SAckTimer
acSysSecurity	1.3.6.1.4.1.5003.9.10.10.1.7
INT acSysSecurityAUPDVerifyCertificates	1.3.6.1.4.1.5003.9.10.10.1.7.13	INTEGER	read-write	This parameter configures the AutoUpdate facility to verify server certificates when using HTTPS. Access: Offline. AC INI-Param: AUPDVerifyCertificates
STR acSysSecurityGenCsrSubjectName	1.3.6.1.4.1.5003.9.10.10.1.7.8	SnmpAdminString	read-write	generate CSR Subject Name. Access: Instant. AC INI-Param: N/A
INT acSysSecurityHTTPSRequireClientCertificate	1.3.6.1.4.1.5003.9.10.10.1.7.12	INTEGER	read-write	Requires client certificates for HTTPS connection. The client certificate must be preloaded on the gateway, and its matching private key must be installed on the managing computer. Time and date must be correctly set on the gateway, for the client certificate to be verified. Access: Offline. AC INI-Param: HTTPSRequireClientCertificate
INT acSysSecurityOcspDefaultResponse	1.3.6.1.4.1.5003.9.10.10.1.7.6	INTEGER	read-write	Determines default OCSP behavior when the server cannot be contacted. 0 = reject peer certificate. 1 = allow peer certificate. . Access: Instant. AC INI-Param: OcspDefaultResponse
INT acSysSecurityOcspEnable	1.3.6.1.4.1.5003.9.10.10.1.7.2	INTEGER	read-write	Enables or disables certificate checking via OCSP. Access: Instant. AC INI-Param: OcspEnable
IP acSysSecurityOcspSecondaryServerIP	1.3.6.1.4.1.5003.9.10.10.1.7.11	InetAddress	read-write	This parameter defines the OCSP secondary server IP address. Range = Legal IP address. Access: Instant. AC INI-Param: OcspSecondaryServerIP
IPt acSysSecurityOcspSecondaryServerIPType	1.3.6.1.4.1.5003.9.10.10.1.7.10	InetAddressType	read-write	This parameter defines the OCSP secondary server's IP address Type. Currently - IPv4 only. Access: Instant. AC INI-Param: N/A
IP acSysSecurityOcspServerIP	1.3.6.1.4.1.5003.9.10.10.1.7.4	InetAddress	read-write	This parameter defines the OCSP server's IP address. Range = Legal IP address. Access: Instant. AC INI-Param: OcspServerIP
IPt acSysSecurityOcspServerIPType	1.3.6.1.4.1.5003.9.10.10.1.7.3	InetAddressType	read-write	This parameter defines the OCSP server's IP address Type. Currently - IPv4 only. Access: Instant. AC INI-Param: N/A
U32 acSysSecurityOcspServerPort	1.3.6.1.4.1.5003.9.10.10.1.7.5	Unsigned32	read-write	This parameter defines the OCSP server's TCP port number. Range = 1 to 32767 . Access: Instant. AC INI-Param: OcspServerPort
STR acSysSecuritySelfSignedCertificateSubjectName	1.3.6.1.4.1.5003.9.10.10.1.7.9	SnmpAdminString	read-write	Access: Instant. AC INI-Param: N/A
INT acSysSecurityTLSFIPS140Mode	1.3.6.1.4.1.5003.9.10.10.1.7.7	INTEGER	read-write	Determines whether to enable the FIPS140 mode for TLS. Access: Offline. AC INI-Param: TLS_Fips140_Mode
U32 acSysSecurityTLSVersion	1.3.6.1.4.1.5003.9.10.10.1.7.1	Unsigned32	read-write	This parameter defines the supported versions of SSL/TLS. When set to 0, SSL/TLS handshakes always start with SSL 2.0 and switch to TLS 1.0 if both peers support it. When set to 1, TLS 1.0 is the only version supported clients attempting to contact the device using SSL 2.0 will be rejected. Possible values: 0 = SSL 2.0, SSL 3.0, and TLS 1.0 are supported (default) 1 = TLS 1.0 will always be used. Access: Offline. AC INI-Param: TLSVersion
acSysSerialIF	1.3.6.1.4.1.5003.9.10.10.1.8
U32 acSysSerialIFBaudRate	1.3.6.1.4.1.5003.9.10.10.1.8.1	Unsigned32	read-write	Enables changes to the Serial Baud Rate for Simplified Message Desk Interface (SMDI). Range = Any value accepted. Recommended standard values: 1200, 2400, 9600, 14400, 19200, 38400, 57600, 115200. Access: Offline. AC INI-Param: SerialBaudRate
U32 acSysSerialIFData	1.3.6.1.4.1.5003.9.10.10.1.8.2	Unsigned32	read-write	Changes the serial data bit for the Simplified Message Desk Interface (SMDI). 7 = 7 Bit 8 = 8 Bit. Access: Offline. AC INI-Param: SerialData
INT acSysSerialIFFlowControl	1.3.6.1.4.1.5003.9.10.10.1.8.5	INTEGER	read-write	Changes the serial flow control for the Simplified Message Desk Interface (SMDI). 0 = None 1 = Hardware. Access: Offline. AC INI-Param: SerialFlowControl
INT acSysSerialIFParity	1.3.6.1.4.1.5003.9.10.10.1.8.3	INTEGER	read-write	Changes the serial parity for the Simplified Message Desk Interface (SMDI). 0 = None 1 = Odd 2 = Even. Access: Offline. AC INI-Param: SerialParity
U32 acSysSerialIFStop	1.3.6.1.4.1.5003.9.10.10.1.8.4	Unsigned32	read-write	Changes the serial stop for the Simplified Message Desk Interface (SMDI). 1 = 1 Bit 2 = 2 Bit. Access: Offline. AC INI-Param: SerialStop
acSysSNMP	1.3.6.1.4.1.5003.9.10.10.1.3.9
U32 acSysSNMPEmsColdStrartIndication	1.3.6.1.4.1.5003.9.10.10.1.3.9.2	Unsigned32	read-write	EMS object to be used as indication to the device's state in the 'eyes' of the EMS. Default - 0. Access: Instant. AC INI-Param: N/A
U32 acSysSNMPKeepAliveTrapPort	1.3.6.1.4.1.5003.9.10.10.1.3.9.1	Unsigned32	read-write	The port to which the keep alive traps are sent to. Access: Instant. AC INI-Param: KeepAliveTrapPort
U32 acSysSNMPWanPort	1.3.6.1.4.1.5003.9.10.10.1.3.9.3	Unsigned32	read-write	This parameter specifies the WAN port number for SNMP requests and responses. If set to 0, WAN access to SNMP is disabled. Range = 0 to 65535. Access: Offline. AC INI-Param: WanMgmtSnmpPort
acSysSRTP	1.3.6.1.4.1.5003.9.10.10.1.7.24.21
U32 acSysSRTPPacketMKISize	1.3.6.1.4.1.5003.9.10.10.1.7.24.21.1	Unsigned32	read-write	Determines the size of the parameter Master Key Identifier (MKI) in SRTP Tx packets. One of the following values: 0 = MKI Disabled 1 - 4 = size (bytes of MKI). Access: Online. AC INI-Param: SRTPTxPacketMKISize
acSysState	1.3.6.1.4.1.5003.9.10.10.2.5
INT acSysStateGWSeverity	1.3.6.1.4.1.5003.9.10.10.2.5.4	INTEGER	read-only	The highest alarm severity on the device. AC INI-Param: N/A
INT acSysStateHAupdateInProgress	1.3.6.1.4.1.5003.9.10.10.2.5.3	INTEGER	read-only	Indicates during update process, which done between active and redundant boards. AC INI-Param: N/A
INT acSysStateIsPstnManagementEnable	1.3.6.1.4.1.5003.9.10.10.2.5.5	INTEGER	read-only	Is Pstn Management Enable 0 - Disable 1 - Enable. AC INI-Param: N/A
INT acSysStateOperational	1.3.6.1.4.1.5003.9.10.10.2.5.2	INTEGER	read-only	The operational state of the gateway. AC INI-Param: N/A
U32 acSysStateTemperature	1.3.6.1.4.1.5003.9.10.10.2.5.1	Unsigned32	read-only	Temperature of the board in degrees Celsius, should not go higher then 60!. AC INI-Param: N/A
acSysSTUN	1.3.6.1.4.1.5003.9.10.10.1.3.6.21
U32 acSysSTUNBindingLifeTime	1.3.6.1.4.1.5003.9.10.10.1.3.6.21.4	Unsigned32	read-write	This parameter is used to define the NAT binding lifetime, in seconds. STUN refreshes the binding information after this time expires. Range = 0 - 2592000. Access: Offline. AC INI-Param: NATBINDINGDEFAULTTIMEOUT
INT acSysSTUNEnable	1.3.6.1.4.1.5003.9.10.10.1.3.6.21.1	INTEGER	read-write	This parameter is used to enable the STUN module, used for NAT traversal of UDP packets. Access: Offline. AC INI-Param: ENABLESTUN
IP acSysSTUNPrimaryServerIP	1.3.6.1.4.1.5003.9.10.10.1.3.6.21.2	IpAddress	read-write	Defines the primary STUN Server IP address. Range = Legal IP address. Access: Offline. AC INI-Param: STUNSERVERPRIMARYIP
IP acSysSTUNSecondaryServerIP	1.3.6.1.4.1.5003.9.10.10.1.3.6.21.3	IpAddress	read-write	Defines the secondary STUN server IP address. Range = Legal IP address. Access: Offline. AC INI-Param: STUNSERVERSECONDARYIP
acSysTDM	1.3.6.1.4.1.5003.9.10.10.1.2
acSysTDMBus	1.3.6.1.4.1.5003.9.10.10.1.2.2
U32 acSysTDMBusOutputPort	1.3.6.1.4.1.5003.9.10.10.1.2.2.3	Unsigned32	read-write	Defines the SC/MVIP/H.100/H.110 output port to be used for the board's channel #0. All other channels then occupy the next timeslots sequentially. Range: 0 to 15 for SC/MVIP 0 to 31 for H.110. Access: Offline. AC INI-Param: TDMBUSOUTPUTPORT
U32 acSysTDMBusOutputStartingChannel	1.3.6.1.4.1.5003.9.10.10.1.2.2.4	Unsigned32	read-write	Defines the outgoing TDM Timeslot for board's channel #0. The remaining channels are organized sequentially. Access: Offline. AC INI-Param: TDMBUSOUTPUTSTARTINGCHANNEL
INT acSysTDMBusSpeed	1.3.6.1.4.1.5003.9.10.10.1.2.2.2	INTEGER	read-write	Selects the TDM bus speed according to the Bus Type as follows: SC = 0/2/3 H.110/H.100 = 3 MVIP = 0 Where: 0 = 2048 kbps 2 = 4096 kbps 3 = 8192 kbps 4 = 16384 kbps Default: TP-260 = 2 All other boards = 3. Access: Offline. AC INI-Param: TDMBUSSPEED
INT acSysTDMBusType	1.3.6.1.4.1.5003.9.10.10.1.2.2.1	INTEGER	read-write	Selects the TDM bus interface to be used (only one TDM bus interface can be enabled at one time although more than one can physically exist on the board). Range: 0 = acMVIP_BUS 1 = acSC_BUS 2 = acFRAMERS 4 = acH100_BUS 5 = EXT TDM 6 = Analog 8 = SW Pstn Default: TP-1610 and TP-2810 = 2 TPM-1100 = 5 TP-260 = 1. Access: Offline. AC INI-Param: TDMBUSTYPE
acSysTDMClock	1.3.6.1.4.1.5003.9.10.10.1.2.1
INT acSysTDMClockAutoFallBackEnable	1.3.6.1.4.1.5003.9.10.10.1.2.1.6	INTEGER	read-write	Enables or disables the PSTN trunk auto-fallback feature. Access: Offline. AC INI-Param: TDMBusPSTNAutoClockEnable
INT acSysTDMClockAutoFallBackRevertingEnable	1.3.6.1.4.1.5003.9.10.10.1.2.1.7	INTEGER	read-write	Enables/disables the PSTN trunk auto-fallback reverting feature. Access: Offline. AC INI-Param: TDMBusPSTNAutoClockRevertingEnable
U32 acSysTDMClockBitsReference	1.3.6.1.4.1.5003.9.10.10.1.2.1.8	Unsigned32	read-write	Configures the BITS clock reference when the board source clock is set to BITS and Fallback is set to manual or non-revertive. 1 = REF_1 2 = REF_2. Access: Online. AC INI-Param: TDMBITSClockReference
INT acSysTDMClockEnableFallBack	1.3.6.1.4.1.5003.9.10.10.1.2.1.2	INTEGER	read-write	Defines the auto fallback of the clock. Range: 0 = Manual 1 = Auto Non-Revertive 2 = Auto Revertive. Access: Online. AC INI-Param: TDMBUSENABLEFALLBACK
INT acSysTDMClockFallbackClock	1.3.6.1.4.1.5003.9.10.10.1.2.1.10	INTEGER	read-write	Selects the fallback clock source on which board synchronizes in the event of clock failure. 4 = PSTN Network 8 = H.110A 9 = H.110B 10 = NetRef1 11 = NetRef2. Access: Online. AC INI-Param: TDMBusFallbackClock
U32 acSysTDMClockLocalReference	1.3.6.1.4.1.5003.9.10.10.1.2.1.3	Unsigned32	read-write	When the clock source is set to Network, this parameter selects the Trunk ID to be used as the clock synchronization source of the board. When using H.110/H.100 bus, this parameter also selects the trunk used as the clock source for the NetRef clock generation (in this case, the clock source must not be set to Network. Range = 0 to (MAX_TRUNK _NUM-1). Access: Online. AC INI-Param: TDMBusLocalReference
INT acSysTDMClockMasterSlaveSelection	1.3.6.1.4.1.5003.9.10.10.1.2.1.4	INTEGER	read-write	Sets SC/MVIP/H.100/H.110 to either: 0 = Slave mode (another board in the system must supply the clock to the TDM bus) or Master mode (the board is the clock source for the TDM bus) or Secondary Master mode (for H100/H110 Bus only). 1 = H110A Master in Master mode 2 = H.110B Master. Access: Online. AC INI-Param: TDMBUSMASTERSLAVESELECTION
INT acSysTDMClockNetRefSpeed	1.3.6.1.4.1.5003.9.10.10.1.2.1.5	INTEGER	read-write	Determines the NetRef frequency (for both generation and synchronization). 0 = 8 kHz 1 = 1.544 MHz 2 = 2.048 MHz. Access: Online. AC INI-Param: TDMBUSNETREFSPEED
INT acSysTDMClockPLLOutOfRange	1.3.6.1.4.1.5003.9.10.10.1.2.1.9	INTEGER	read-write	Determines the valid PPM range outside the Stratum 3 standard. This parameter is only relevant for the TP8410 on the Mediant 3000. This parameter is enabled when bspTimingModuleCfgTimingMode is set to TM_External_MODE(1). One of the following possible values: OOR_9_2to12ppm(0),OOR_40to52ppm(1),OOR_100to130ppm(2),OOR_64to83ppm(3),OOR_13_8to18ppm(4),OOR_24_6to32ppm(5),OOR_36_6to47_5ppm(6),OOR_52to67_5ppm(7). Access: Online. AC INI-Param: PLLOutOfRange
INT acSysTDMClockSource	1.3.6.1.4.1.5003.9.10.10.1.2.1.1	INTEGER	read-write	Selects the clock source on which the board synchronizes. 1 = Local oscillator 3 = MVIP 4 = PSTN Network 8 = H.110A 9 = H.110B 10 = NetRef1 11 = NetRef2 12 = SC2M 13 = SC4M 14 = SC8M 15 = BITS 16 = Network-B 17 = ATM-OC3 18 = ATM-OC3-B 19 = ATM-OC12 20 = Network-DS3-1 21 = Network-DS3-2 22 = Network-DS3-3 Default = 1 TP-1610 = 3. Access: Online. AC INI-Param: TDMBUSCLOCKSOURCE
acSysTelnet	1.3.6.1.4.1.5003.9.10.10.1.3.7
INT acSysTelnetServerEnable	1.3.6.1.4.1.5003.9.10.10.1.3.7.1	INTEGER	read-write	Enables or disables the embedded Telnet server. Telnet is disabled by default for security reasons. 0 = Disable 1= Enable 2 = SSL mode (if available - requires an SSL-aware Telnet client software) SSL mode is not available on the MP-108 / MP-124 media gateways. Access: Instant. AC INI-Param: TelnetServerEnable
U32 acSysTelnetServerIdleDisconnect	1.3.6.1.4.1.5003.9.10.10.1.3.7.3	Unsigned32	read-write	This parameter is used to set the timeout for disconnection of an idle Telnet session (minutes). When set to zero, idle sessions are not disconnected. Range: Any number. Access: Offline. AC INI-Param: TelnetServerIdleDisconnect
U32 acSysTelnetServerPort	1.3.6.1.4.1.5003.9.10.10.1.3.7.2	Unsigned32	read-write	Defines the port number for the embedded Telnet server. Range = Valid port number. Access: Online. AC INI-Param: TELNETSERVERPORT
U32 acSysTelnetServerWanPort	1.3.6.1.4.1.5003.9.10.10.1.3.7.8	Unsigned32	read-write	Determines the WAN Telnet port of the device. If set to 0, WAN Telnet access will not be possible. Range = 0 to 65535 (other restrictions may apply in this range). Access: Offline. AC INI-Param: WanMgmtTelnetPort
STR acSysTelnetSSHAdminKey	1.3.6.1.4.1.5003.9.10.10.1.3.7.6	SnmpAdminString	read-write	This parameter holds an RSA public key for strong authentication to the SSH interface (if enabled). The value should be a base64-encoded string see the Security appendix for additional information. Access: Instant. AC INI-Param: SSHAdminKey
INT acSysTelnetSSHRequirePublicKey	1.3.6.1.4.1.5003.9.10.10.1.3.7.7	INTEGER	read-write	Enables or disables RSA public keys in SSH. When set to 0, RSA public keys are optional (if SSHAdminKey is set). When set to 1, RSA public keys are mandatory. Access: Instant. AC INI-Param: SSHRequirePublicKey
INT acSysTelnetSSHServerEnable	1.3.6.1.4.1.5003.9.10.10.1.3.7.5	INTEGER	read-write	Enables or disables the embedded SSH server. 0 = Disable 1= Enable . Access: Online. AC INI-Param: SSHServerEnable
U32 acSysTelnetSSHServerPort	1.3.6.1.4.1.5003.9.10.10.1.3.7.4	Unsigned32	read-write	Defines the port number for the embedded SSH server. Range = Valid port number. Access: Online. AC INI-Param: SSHServerPort
U32 acSysTelnetWanSSHServerPort	1.3.6.1.4.1.5003.9.10.10.1.3.7.9	Unsigned32	read-write	Determines the WAN Telnet port of the device. If set to 0, WAN Telnet access will not be possible. Range = 0 to 65535 (other restrictions may apply in this range). Access: Offline. AC INI-Param: WanMgmtSSHPort
acSystem	1.3.6.1.4.1.5003.9.10.10
acSystemAction	1.3.6.1.4.1.5003.9.10.10.3
acSystemChassis	1.3.6.1.4.1.5003.9.10.10.4
BIT acSystemChassisDryContactsInStatus	1.3.6.1.4.1.5003.9.10.10.4.2	Bits	read-only	Indicates current state of the alarm dry contacts - in signals (1 signals). The role of each input signal should be according to the customer's requirements. This is a bit-map of possible conditions. AC INI-Param: N/A
BIT acSystemChassisDryContactsOutStatus	1.3.6.1.4.1.5003.9.10.10.4.1	Bits	read-only	Indicates current state of the alarm dry contacts � out signals (3 signals). This is a bit-map of possible conditions. AC INI-Param: N/A
U32 acSystemChassisLastChanged	1.3.6.1.4.1.5003.9.10.10.4.3	Unsigned32	read-only	The value of sysUpTime at the time a row is modified in any of the acSystemChassis subtree's objects. AC INI-Param: N/A
acSystemConfiguration	1.3.6.1.4.1.5003.9.10.10.1
acSystemStatus	1.3.6.1.4.1.5003.9.10.10.2
acSysTime	1.3.6.1.4.1.5003.9.10.10.2.7
U32 acSysTimeUp	1.3.6.1.4.1.5003.9.10.10.2.7.1	Unsigned32	read-only	Time (in Seconds) that the board is alive. AC INI-Param: N/A
acSysTiming	1.3.6.1.4.1.5003.9.10.10.1.14
INT acSysTimingClockToDeriveA	1.3.6.1.4.1.5003.9.10.10.1.14.3	INTEGER	read-write	Which Clock to use in sync mode. Access: Online. AC INI-Param: TMClockToDerive_A
INT acSysTimingClockToDeriveB	1.3.6.1.4.1.5003.9.10.10.1.14.4	INTEGER	read-write	Which Clock to use in sync mode. Access: Online. AC INI-Param: TMClockToDerive_B
INT acSysTimingE1LineBuildOut	1.3.6.1.4.1.5003.9.10.10.1.14.9	INTEGER	read-write	Sets the transmission power between the timing module on the SAT and the E1 external reference clock (ohms). This parameter is only relevant for the Mediant 3000.This parameter is enabled when bspTimingModuleCfgTimingMode is set to TM_External_MODE(1). One of the following values: E_75_OHM_with_high_return_loss(4),E_120_OHM_with_high_return_loss(5),E_75_OHM_normal_PLUS_enable_transmit_and_receive_gapped_clock(6),E_120_OHM_normal_PLUS_enable_transmit_and_receive_gapped_clock(7),E_75_OHM_normal(0),E_120_OHM_normal(1). Access: Online. AC INI-Param: TME1LineBuildOut
INT acSysTimingExternalIFType	1.3.6.1.4.1.5003.9.10.10.1.14.5	INTEGER	read-write	Defines the external line reference (BITS) transmission format. Access: Online. AC INI-Param: TMExternalIFType
INT acSysTimingLoopBackRef1	1.3.6.1.4.1.5003.9.10.10.1.14.6	INTEGER	read-write	Enables loopback state, by connecting Rx path towards Tx path. Access: Online. AC INI-Param: TMLoopBackExternalRef1
INT acSysTimingLoopBackRef2	1.3.6.1.4.1.5003.9.10.10.1.14.7	INTEGER	read-write	Enables loopback state, by connecting Rx path towards Tx path. Access: Online. AC INI-Param: TMLoopBackExternalRef2
INT acSysTimingMode	1.3.6.1.4.1.5003.9.10.10.1.14.1	INTEGER	read-write	Determines the PSTN Timing synchonization mode of the Gateway. One of the following values: TM_External_MODE(1) -External Timing mode - use the SAT trunks Centralized Line Timing to synchronize the Gateway with one of the PSTN interfaces. TM_LineSync_MODE(2) -Distributed Line Timing mode (for the 1610 boards)- without using the SAT timing module. TM_Standalone_MODE(0) -Non-synchronized mode - each board or TPM is synchronized internally from one of the PSTN interfaces without using the SAT timing module. Access: Online. AC INI-Param: TMMode
acSysTimingModule	1.3.6.1.4.1.5003.9.10.10.4.26
INT acSysTimingT1LineBuildOut	1.3.6.1.4.1.5003.9.10.10.1.14.10	INTEGER	read-write	External Reference Transmit Line Build Out. Access: Online. AC INI-Param: TMT1LineBuildOut
INT acSysTimingTransmitControl	1.3.6.1.4.1.5003.9.10.10.1.14.8	INTEGER	read-write	Enables loopback state, by connecting Rx path towards Tx path. Access: Online. AC INI-Param: TMTransmitControl
U32 acSysTimingValidationTime	1.3.6.1.4.1.5003.9.10.10.1.14.2	Unsigned32	read-write	Reference validation time. Applicable for External timing and Line timing timing references. Range: 0 - 15 minutes. Resolution: 1 minute. Access: Online. AC INI-Param: TMReferenceValidationTime
acSysTransmission	1.3.6.1.4.1.5003.9.10.10.1.13
INT acSysTransmissionType	1.3.6.1.4.1.5003.9.10.10.1.13.1	INTEGER	read-write	Sets the PSTN Transmission type for the board: optical SONET / SDH or copper DS3. Access: Offline. AC INI-Param: PSTNTransmissionType
acSysType	1.3.6.1.4.1.5003.9.10.10.2.1
U32 acSysTypeCPUSpeed	1.3.6.1.4.1.5003.9.10.10.2.1.4	Unsigned32	read-only	CPU Speed. AC INI-Param: N/A
U32 acSysTypeDSP	1.3.6.1.4.1.5003.9.10.10.2.1.2	Unsigned32	read-only	Dsp Type. AC INI-Param: N/A
INT acSysTypeModule	1.3.6.1.4.1.5003.9.10.10.2.1.3	INTEGER	read-only	AC INI-Param: N/A
INT acSysTypeProduct	1.3.6.1.4.1.5003.9.10.10.2.1.1	INTEGER	read-only	The type of the Board. AC INI-Param: N/A
acSysUpload	1.3.6.1.4.1.5003.9.10.10.3.1.3
U32 acSysUploadActionID	1.3.6.1.4.1.5003.9.10.10.3.1.3.5	Unsigned32	read-write	This field is for management use and is aimed to distinguish different managers managing a single device. Access: Instant. AC INI-Param: N/A
STR acSysUploadActionResult	1.3.6.1.4.1.5003.9.10.10.3.1.3.6	SnmpAdminString	read-only	Action result. Includes action status (success, failure or inProgress), action ID. AC INI-Param: N/A
INT acSysUploadActionType	1.3.6.1.4.1.5003.9.10.10.3.1.3.1	INTEGER	read-write	Action to be carried out. Setting this field triggers the action. File upload supported for iniFile(1), v5PortFile(16) and DataConfigurationFile(17) only access is instant. File removal supported for all other then iniFile(1), v5PortFile(16) and DataConfigurationFile(17), (v5PortFile removal is done via acV5PortActionType) access is offline. Access: Instant. AC INI-Param: N/A
I32 acSysUploadFileNumber	1.3.6.1.4.1.5003.9.10.10.3.1.3.3	Integer32	read-write	File number for file types that have more then one file instance, such as CAS, VideoFont etc'. Access: Instant. AC INI-Param: N/A
INT acSysUploadFileType	1.3.6.1.4.1.5003.9.10.10.3.1.3.2	INTEGER	read-write	The file type to be uploaded. Note - for file types with more then one instance (like CAS files) use the acSysActionFileInstance to specify which instance you want to upload. Access: Instant. AC INI-Param: N/A
STR acSysUploadFileURI	1.3.6.1.4.1.5003.9.10.10.3.1.3.4	SnmpAdminString	read-write	URI indicating file location to be downloaded to. Access: Instant. AC INI-Param: N/A
acSysVersion	1.3.6.1.4.1.5003.9.10.10.2.2
U32 acSysVersionFlash	1.3.6.1.4.1.5003.9.10.10.2.2.2	Unsigned32	read-only	Flash [BootLoader] Version. AC INI-Param: N/A
U32 acSysVersionIniFile	1.3.6.1.4.1.5003.9.10.10.2.2.3	Unsigned32	read-only	Ini file version. AC INI-Param: INIFileVersion
STR acSysVersionSoftware	1.3.6.1.4.1.5003.9.10.10.2.2.1	SnmpAdminString	read-only	TrunkPack Software Version. AC INI-Param: N/A
STR acSysVersionSoftwareDate	1.3.6.1.4.1.5003.9.10.10.2.2.4	SnmpAdminString	read-only	TrunkPack Software Date. AC INI-Param: N/A
acSysVLAN	1.3.6.1.4.1.5003.9.10.10.1.3.10
U32 acSysVLANBronzeServiceClassDiffServ	1.3.6.1.4.1.5003.9.10.10.1.3.10.13	Unsigned32	read-write	Sets the DiffServ for the Bronze service class content. Range = 0 to 63 Default = 10. Access: Online. AC INI-Param: BRONZESERVICECLASSDIFFSERV
U32 acSysVLANBronzeServiceClassPriority	1.3.6.1.4.1.5003.9.10.10.1.3.10.7	Unsigned32	read-write	Sets the priority for the Bronze service class content. Range = 0 to 7 Default = 2. Access: Online. AC INI-Param: VLANBRONZESERVICECLASSPRIORITY
U32 acSysVLANControlVlanId	1.3.6.1.4.1.5003.9.10.10.1.3.10.2	Unsigned32	read-write	Sets the control VLAN identifier. Range: 1 to 4094. Access: Online. AC INI-Param: VLANCONTROLVLANID
U32 acSysVLANGoldServiceClassDiffServ	1.3.6.1.4.1.5003.9.10.10.1.3.10.12	Unsigned32	read-write	Sets the DiffServ for the Gold service class content. Range = 0 to 63 Default = 26. Access: Online. AC INI-Param: GOLDSERVICECLASSDIFFSERV
U32 acSysVLANGoldServiceClassPriority	1.3.6.1.4.1.5003.9.10.10.1.3.10.6	Unsigned32	read-write	Sets the priority for the Gold service class content. Range = 0 to 7 Default = 4. Access: Online. AC INI-Param: VLANGOLDSERVICECLASSPRIORITY
INT acSysVlanMapAction	1.3.6.1.4.1.5003.9.10.10.1.3.10.21.1.3	INTEGER	read-create	Mangement Field for ACTIONS. Internal parameter. AC INI-Param: N/A
INT acSysVlanMapActionRes	1.3.6.1.4.1.5003.9.10.10.1.3.10.21.1.4	INTEGER	read-only	Mangement Field for ACTIONS RESULT. Internal parameter. AC INI-Param: N/A
U32 acSysVlanMapDiffServ	1.3.6.1.4.1.5003.9.10.10.1.3.10.21.1.5	Unsigned32	read-create	Mapping of DiffServ (DSCP) to Vlan Priorities (IEEE 802.1p). Access: Online. AC INI-Param: DiffServToVlanPriority_DiffServ
acSysVlanMapEntry	1.3.6.1.4.1.5003.9.10.10.1.3.10.21.1		not-accessible
U32 acSysVlanMapIndex	1.3.6.1.4.1.5003.9.10.10.1.3.10.21.1.1	Unsigned32	not-accessible	Index Field for line. Internal parameter. AC INI-Param: DiffServToVlanPriority_Index
ROW acSysVlanMapRowStatus	1.3.6.1.4.1.5003.9.10.10.1.3.10.21.1.2	RowStatus	read-create	ROWSTATUS field for line. Internal parameter. AC INI-Param: N/A
acSysVlanMapTable	1.3.6.1.4.1.5003.9.10.10.1.3.10.21		not-accessible
U32 acSysVlanMapVlanPriority	1.3.6.1.4.1.5003.9.10.10.1.3.10.21.1.6	Unsigned32	read-create	Mapping of DiffServ (DSCP) to Vlan Priorities (IEEE 802.1p). Access: Online. AC INI-Param: DiffServToVlanPriority_VlanPriority
U32 acSysVLANMediaVlanId	1.3.6.1.4.1.5003.9.10.10.1.3.10.3	Unsigned32	read-write	Sets the media VLAN identifier. Range: 1 to 4094. Access: Online. AC INI-Param: VLANMEDIAVLANID
U32 acSysVLANMode	1.3.6.1.4.1.5003.9.10.10.1.3.10.15	Unsigned32	read-write	Sets the VLAN functionality. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: VLANMODE
U32 acSysVLANNetworkServiceClassDiffServ	1.3.6.1.4.1.5003.9.10.10.1.3.10.9	Unsigned32	read-write	This parameter is used to set the DiffServ for Network service class content. Range = 0 to 63 Default = 48. Access: Online. AC INI-Param: NETWORKSERVICECLASSDIFFSERV
U32 acSysVLANNetworkServiceClassPriority	1.3.6.1.4.1.5003.9.10.10.1.3.10.4	Unsigned32	read-write	This parameter is used to set the priority for Network service class content. Range = 0 to 7 Default = 7. Access: Online. AC INI-Param: VLANNETWORKSERVICECLASSPRIORITY
U32 acSysVLANOamVlanId	1.3.6.1.4.1.5003.9.10.10.1.3.10.1	Unsigned32	read-write	Sets the OAMP (Operation, Administration, Management and Provisioning) VLAN identifier. Range: 1 to 4094. Access: Online. AC INI-Param: VLANOAMVLANID
U32 acSysVLANPremiumServiceClassControlDiffServ	1.3.6.1.4.1.5003.9.10.10.1.3.10.11	Unsigned32	read-write	Sets the DiffServ for the Premium service class content and control traffic. Range: 0 to 63. Access: Online. AC INI-Param: PREMIUMSERVICECLASSCONTROLDIFFSERV
U32 acSysVLANPremiumServiceClassControlPriority	1.3.6.1.4.1.5003.9.10.10.1.3.10.8	Unsigned32	read-write	Sets the priority for the Premium service class content and control traffic. Range = 0 to 7 Default = 6. Access: Online. AC INI-Param: VLANPREMIUMSERVICECLASSCONTROLPRIORITY
U32 acSysVLANPremiumServiceClassMediaDiffServ	1.3.6.1.4.1.5003.9.10.10.1.3.10.10	Unsigned32	read-write	This parameter is used to set the DiffServ for Premium service class content and media traffic. Range = 0 to 63. Access: Online. AC INI-Param: PREMIUMSERVICECLASSMEDIADIFFSERV
U32 acSysVLANPremiumServiceClassMediaPriority	1.3.6.1.4.1.5003.9.10.10.1.3.10.5	Unsigned32	read-write	Sets the priority for the Premium service class content and media traffic. Range = 0 to 7 Default = 6. Access: Online. AC INI-Param: VLANPREMIUMSERVICECLASSMEDIAPRIORITY
U32 acSysVLANVlanNativeVlanId	1.3.6.1.4.1.5003.9.10.10.1.3.10.14	Unsigned32	read-write	Sets the native VLAN identifier. Access: Online. AC INI-Param: VLANNATIVEVLANID
acSysVoicePrompt	1.3.6.1.4.1.5003.9.10.10.2.8
U32 acSysVoicePromptMaxFreeMemorySize	1.3.6.1.4.1.5003.9.10.10.2.8.2	Unsigned32	read-only	Get the maximu voice prompt memory free size. AC INI-Param: N/A
U32 acSysVoicePromptTotalMemorySize	1.3.6.1.4.1.5003.9.10.10.2.8.1	Unsigned32	read-only	Get the total voice prompt memory size. AC INI-Param: N/A
acSysWEB	1.3.6.1.4.1.5003.9.10.10.1.3.4
acSysWEBAccess	1.3.6.1.4.1.5003.9.10.10.1.3.5
U32 acSysWEBAccessAction	1.3.6.1.4.1.5003.9.10.10.1.3.5.1.1.2	Unsigned32	read-create	WEB Access action. AC INI-Param: WEBAccessAction
U32 acSysWEBAccessActionResult	1.3.6.1.4.1.5003.9.10.10.1.3.5.1.1.3	Unsigned32	read-only	WEB Access action result. AC INI-Param: N/A
acSysWEBAccessEntry	1.3.6.1.4.1.5003.9.10.10.1.3.5.1.1		not-accessible
INT acSysWEBAccessIndex	1.3.6.1.4.1.5003.9.10.10.1.3.5.1.1.4	INTEGER	read-only	WEB Access index. AC INI-Param: N/A
U32 acSysWEBAccessRowStatus	1.3.6.1.4.1.5003.9.10.10.1.3.5.1.1.1	Unsigned32	read-write	WEB Basic row-status. AC INI-Param: WEBAccessRowStatus
acSysWEBAccessTable	1.3.6.1.4.1.5003.9.10.10.1.3.5.1		not-accessible
STR acSysWEBAccessUserCode	1.3.6.1.4.1.5003.9.10.10.1.3.5.1.1.6	SnmpAdminString	read-create	WEB Basic userAccess. Access: Instant. AC INI-Param: WEBAccessUserCode
STR acSysWEBAccessUserName	1.3.6.1.4.1.5003.9.10.10.1.3.5.1.1.5	SnmpAdminString	read-create	WEB Basic user name. Range = String[26]. Access: Instant. AC INI-Param: WEBAccessUserName
INT acSysWEBAccessWebAuthMode	1.3.6.1.4.1.5003.9.10.10.1.3.5.1.1.7	INTEGER	read-create	Selects HTTP basic (clear text) or digest (MD5) authentication for the web interface. When set to 0, basic authentication (clear text) will be used. When set to 1, digest authentication (MD5) will be used. When set to 2, digest authentication (MD5) will be used for HTTP, while basic authentication will be used for HTTPS. Note that turning on RADIUS login forces basic authentication. Access: Instant. AC INI-Param: WebAuthMode
acSysWEBACLEntry	1.3.6.1.4.1.5003.9.10.10.1.3.4.21.1		not-accessible
U32 acSysWEBACLIndex	1.3.6.1.4.1.5003.9.10.10.1.3.4.21.1.1	Unsigned32	read-only	WEB ACL (Access Control List) index. AC INI-Param: N/A
IP acSysWEBACLIP	1.3.6.1.4.1.5003.9.10.10.1.3.4.21.1.2	IpAddress	read-write	Allows IP addresses to connect to the Web interface. Set to zeroes to allow all IP addresses. Range: Valid IP address . Access: Instant. AC INI-Param: WEBACCESSLIST
acSysWEBACLTable	1.3.6.1.4.1.5003.9.10.10.1.3.4.21		not-accessible	Access control list for the WEB.
INT acSysWEBConfigDisable	1.3.6.1.4.1.5003.9.10.10.1.3.4.1	INTEGER	read-write	Enables or disables Web Configuration. 0 = Read & Write mode (default) 1 = Read Only mode. Access: Offline. AC INI-Param: DISABLEWEBCONFIG
U32 acSysWEBDenyAuthenticationTimer	1.3.6.1.4.1.5003.9.10.10.1.3.4.6	Unsigned32	read-write	Defines the time the next authentication attempt from the last authentication faild IP should be denied. The range can be any value from 0 - 86400 in seconds. Access: Online. AC INI-Param: DenyAuthenticationTimer
STR acSysWEBHTTPSCipherString	1.3.6.1.4.1.5003.9.10.10.1.3.4.5	SnmpAdminString	read-write	Requires client certificates for HTTPS connection. The client certificate must be preloaded on the gateway, and its matching private key must be installed on the managing computer. Time and date must be correctly set on the gateway, for the client certificate to be verified. Access: Offline. AC INI-Param: HTTPSCipherString
INT acSysWEBHTTPSOnly	1.3.6.1.4.1.5003.9.10.10.1.3.4.2	INTEGER	read-write	Use this parameter to allow only HTTPS connections (force security). When set to 1, unencrypted HTTP (normally, port 80) is blocked. Access: Offline. AC INI-Param: HTTPSOnly
U32 acSysWEBHTTPSPort	1.3.6.1.4.1.5003.9.10.10.1.3.4.3	Unsigned32	read-write	Determine the local Secure HTTPS port of the device. The default port is 443. Range = 1-65535 (other restrictions may apply in this range). Access: Offline. AC INI-Param: HTTPSPORT
acSysWebStat	1.3.6.1.4.1.5003.9.10.10.2.6.3
INT acSysWebStatPasswordControlViaSNMP	1.3.6.1.4.1.5003.9.10.10.2.6.3.1	INTEGER	read-only	If set to 1 it will allow changing the web interface username and password via SNMP. AC INI-Param: WEBPasswordControlViaSNMP
U32 acSysWEBWanHttpPort	1.3.6.1.4.1.5003.9.10.10.1.3.4.7	Unsigned32	read-write	Determines the WAN HTTP port of the device. If set to 0, WAN HTTP access will not be possible. Range = 0 to 65535 (other restrictions may apply in this range). Access: Offline. AC INI-Param: WanMgmtHttpPort
U32 acSysWEBWanHttpsPort	1.3.6.1.4.1.5003.9.10.10.1.3.4.8	Unsigned32	read-write	Determines the WAN HTTPS port of the device. If set to 0, WAN HTTPS access will not be possible. Range = 0 to 65535 (other restrictions may apply in this range). Access: Offline. AC INI-Param: WanMgmtHttpsPort
INT acSysWEBWebUseRadiusLogin	1.3.6.1.4.1.5003.9.10.10.1.3.4.4	INTEGER	read-write	Uses the RADIUS (Remote Authentication Dial-In User Server/Service) for Web interface authentication. Make sure that ENABLERADIUS is on. Use of this parameter without HTTPSONLY = 1 is not recommended. Access: Instant. AC INI-Param: WEBRADIUSLOGIN
acVoiceStream	1.3.6.1.4.1.5003.9.10.10.1.9
INT acVoiceStreamStatus	1.3.6.1.4.1.5003.9.10.10.1.9.1	INTEGER	read-write	Enables/disables the voice streaming for all voice source types (HTTP, NFS, Local Storage). When enabled, the module requires some system resources, such as tasks and memory allocation. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: N/A
INT acVoiceStreamUploadMethod	1.3.6.1.4.1.5003.9.10.10.1.9.2	INTEGER	read-write	Defines the HTTP request type for uploading the voice stream to the file server. 0 = POST 1 = PUT. Access: Offline. AC INI-Param: N/A
STR acVoiceStreamUploadPostUri	1.3.6.1.4.1.5003.9.10.10.1.9.3	SnmpAdminString	read-write	Defines the URI used on the POST request, to upload voice data from the media server to a web server. This parameter is used only when using the HTTP POST for recording and the command is not issued by the Lib (tpncp protocol). The path needs to be set to the upload script on the web server. . Access: Offline. AC INI-Param: N/A

RFC description

AudioCodes media gateway system configuration MIB for control protocols (MGCP, MEGACO, H.323, SIP) and board management.

Start monitoring AudioCodes Mediant-series gateways/media servers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AC-SYSTEM-MIB

What Is AC-SYSTEM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description