EPPC-MIB

All MIBs › EPPC-MIB

Category: Domain: Power/UPS

Description: Proprietary UPS MIB providing management objects for three-phase power, battery, and module status monitoring on enterprise UPS systems.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is EPPC-MIB?

This is a proprietary UPS (uninterruptible power supply) MIB providing management objects for enterprise three-phase UPS systems, covering power, battery, and module status. Based on its object hierarchy (upsAgent, upsE, upsEIdentity, and associated traps), it exposes power-subsystem data such as UPS identity/agent information and status of UPS modules, consistent with typical UPS MIB structures covering input/output power, battery charge, and load. Its core purpose is monitoring the hardware status of the UPS itself, including battery health, module/phase status, and fault conditions communicated via upsETraps, making it directly relevant to power infrastructure uptime monitoring. No dependency on another standard MIB is indicated in the provided material, suggesting it is a vendor-specific, self-contained UPS MIB rather than an extension of the standard UPS-MIB (RFC 1628). It is deployed in data centers and facilities using three-phase UPS systems from this vendor to protect critical power infrastructure for racks of network and server equipment. Engineers can download the EPPC-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in EPPC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

three-phase UPS systems

Monitoring Examples

An administrator would poll objects under upsEIdentity to confirm the UPS model/agent identity and firmware are as expected, and monitor status objects under upsE/upsAgent for battery and module health to catch a failing battery module before it causes an outage. Receiving a trap from upsETraps would alert the admin to an event such as a phase failure, battery low condition, or module fault requiring immediate attention on a three-phase UPS supporting critical infrastructure.

What Can Be Monitored

UPS module status
battery status
power/phase status
UPS fault/event traps

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
IpAddress
enterprises

From SNMPv2-TC

DisplayString

From UPS-MIB

NonNegativeInteger
PositiveInteger

OIDs

OID symbolic	OID numeric	Type	Access	Description
ppc	1.3.6.1.4.1.935
device	1.3.6.1.4.1.935.10
upsAgent	1.3.6.1.4.1.935.10.1
upsE	1.3.6.1.4.1.935.10.1.1
upsEIdentity	1.3.6.1.4.1.935.10.1.1.1
STR upsEIdentityManufacturer	1.3.6.1.4.1.935.10.1.1.1.1	DisplayString	read-only	The name of the UPS manufacturer.
STR upsEIdentityModel	1.3.6.1.4.1.935.10.1.1.1.2	DisplayString	read-only	The UPS Model designation.
STR upsEIdentityUPSFirmwareVerison	1.3.6.1.4.1.935.10.1.1.1.3	DisplayString	read-only	The UPS firmware/software version(s).
STR upsEIndentityUPSSerialNumber	1.3.6.1.4.1.935.10.1.1.1.4	DisplayString	read-only	optional. Most UPS don't supply the value of UPS serial No.
STR upsEIdentityDescription	1.3.6.1.4.1.935.10.1.1.1.5	DisplayString	read-write	A string to identify the UPS. This object should be set by the administrator.
STR upsEIdentityAgentSoftwareVerison	1.3.6.1.4.1.935.10.1.1.1.6	DisplayString	read-only	The Network Management Card software/firmware version. This variable may or may not have the same value as upsEIdentGroupUPSSoftwareVersion in some implementations.
STR upsEIdentityAttachedDevices	1.3.6.1.4.1.935.10.1.1.1.7	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator
upsESystemSummary	1.3.6.1.4.1.935.10.1.1.2
INT upsESystemStatus	1.3.6.1.4.1.935.10.1.1.2.1	INTEGER	read-only	The indication of UPS system status.
INT upsESystemTemperature	1.3.6.1.4.1.935.10.1.1.2.2	INTEGER	read-only	The temperature of UPS presented in 0.1 degree.
STR upsESystemWarningCode	1.3.6.1.4.1.935.10.1.1.2.3	DisplayString	read-only	The warning code of UPS. Please refer the warning table of 'Q6' for details.
STR upsESystemFaultCode	1.3.6.1.4.1.935.10.1.1.2.4	DisplayString	read-only	The fault code of UPS.Please refer the fault code of 'Q6' for details.
NUM upsESystemConfigInputVoltage	1.3.6.1.4.1.935.10.1.1.2.5	NonNegativeInteger	read-only	The magnitude of the nominal input voltage presented in 0.1 V. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
NUM upsESystemConfigInputFrequence	1.3.6.1.4.1.935.10.1.1.2.6	NonNegativeInteger	read-only	The nominal input frequency presented in 0.1 Hz. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
NUM upsESystemConfigOutputVoltage	1.3.6.1.4.1.935.10.1.1.2.7	NonNegativeInteger	read-only	The magnitude of the nominal output voltage presented in 0.1V. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2
NUM upsESystemConfigOutputFrequency	1.3.6.1.4.1.935.10.1.1.2.8	NonNegativeInteger	read-only	The nominal output frequency presented in 0.1Hz. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
NUM upsESystemConfigOutputVA	1.3.6.1.4.1.935.10.1.1.2.9	NonNegativeInteger	read-only	The magnitude of the nominal Volt-Amp rating presented in VA.
NUM upsESystemConfigOutputPower	1.3.6.1.4.1.935.10.1.1.2.10	NonNegativeInteger	read-only	The magnitude of the nominal true power rating presented in W .
NUM upsESystemConfigOutputLoadHighSetPoint	1.3.6.1.4.1.935.10.1.1.2.11	NonNegativeInteger	read-write	The maximum output load allowed before the load is too high for UPS operation
NUM upsESystemConfigOverTemperatureSetPoint	1.3.6.1.4.1.935.10.1.1.2.12	NonNegativeInteger	read-write	The maximum temperature allowed before the UPS operation temperature is too high, presented in 0.1 degree.
INT upsESystemInputSourceNum	1.3.6.1.4.1.935.10.1.1.2.13	INTEGER	read-only	The present external source of input power.
CTR upsESystemInputLineBads	1.3.6.1.4.1.935.10.1.1.2.14	Counter	read-only	The number of times the Input was out of tolerance in voltage or frequency. Its value should be initialized 0 after agent restarting.
NUM upsESystemInputNumPhases	1.3.6.1.4.1.935.10.1.1.2.15	PositiveInteger	read-only	The number of input phase utilized is this device, serves as the table index. This value indicate the device initialized feature.
upsESystemInputTable	1.3.6.1.4.1.935.10.1.1.2.16		not-accessible	A list of input table entries. The number of entries is given by the value of upsESystemInputNumPhase.
upsESystemInputEntry	1.3.6.1.4.1.935.10.1.1.2.16.1		not-accessible	An entry containing information applicable to a particular input line.
NUM upsESystemInputPhase	1.3.6.1.4.1.935.10.1.1.2.16.1.1	PositiveInteger	not-accessible	The number of the phase. Serves as index for input table
NUM upsESystemInputFrequency	1.3.6.1.4.1.935.10.1.1.2.16.1.2	NonNegativeInteger	read-only	The measured input frquency from the UPS meters in 0.1Hz.
NUM upsESystemInputVoltage	1.3.6.1.4.1.935.10.1.1.2.16.1.3	NonNegativeInteger	read-only	The measured input voltage from the UPS meters in 0.1 volts
NUM upsESystemInputCurrent	1.3.6.1.4.1.935.10.1.1.2.16.1.4	NonNegativeInteger	read-only	The measured input mandatory from the UPS meters in 0.1 amps.
NUM upsESystemInputWatts	1.3.6.1.4.1.935.10.1.1.2.16.1.5	NonNegativeInteger	read-only	The measured input real power in watts.
NUM upsESystemOutputNumPhase	1.3.6.1.4.1.935.10.1.1.2.17	PositiveInteger	read-only	The number of metered output phases, serves as the table index. This value indicate the device initialized feature.
upsESystemOutputTable	1.3.6.1.4.1.935.10.1.1.2.18		not-accessible	A list of output table entries. The number of entries is given by the value of upsESystemOutputNumPhase.
upsESystemOutputEntry	1.3.6.1.4.1.935.10.1.1.2.18.1		not-accessible	An entry containing information applicable to a particular line.
NUM upsESystemOutputPhase	1.3.6.1.4.1.935.10.1.1.2.18.1.1	PositiveInteger	not-accessible	The number of the phase. Serves as index for output table
NUM upsESystemOutputFrequency	1.3.6.1.4.1.935.10.1.1.2.18.1.2	NonNegativeInteger	read-only	The measured output frequency from the UPS meters in 0.1Hz.
NUM upsESystemOutputVoltage	1.3.6.1.4.1.935.10.1.1.2.18.1.3	NonNegativeInteger	read-only	The measured output voltage from the UPS meters in 0.1 volts
NUM upsESystemOutputCurrent	1.3.6.1.4.1.935.10.1.1.2.18.1.4	NonNegativeInteger	read-only	The measured output mandatory from the UPS meters in 0.1 amps.
NUM upsESystemOutputWatts	1.3.6.1.4.1.935.10.1.1.2.18.1.5	NonNegativeInteger	read-only	The measured output real power in watts.
NUM upsESystemOutputVA	1.3.6.1.4.1.935.10.1.1.2.18.1.6	NonNegativeInteger	read-only	The measured output real complex power in VA.
NUM upsESystemOutputLoad	1.3.6.1.4.1.935.10.1.1.2.18.1.7	NonNegativeInteger	read-only	The UPS output load in percent of rated capacity.
NUM upsESystemBypassNumPhase	1.3.6.1.4.1.935.10.1.1.2.19	PositiveInteger	read-only	The number of bypass phases, serves as the table index. This value indicate the device initialized feature
upsESystemBypassTable	1.3.6.1.4.1.935.10.1.1.2.20		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsESystemBypassNumPhase.
upsESystemBypassEntry	1.3.6.1.4.1.935.10.1.1.2.20.1		not-accessible	An entry containing information applicable to a particular line.
NUM upsESystemBypassPhase	1.3.6.1.4.1.935.10.1.1.2.20.1.1	PositiveInteger	not-accessible	The number of the phase. Serves as index for bypass table
NUM upsESystemBypassFrequency	1.3.6.1.4.1.935.10.1.1.2.20.1.2	NonNegativeInteger	read-only	The measured bypass frequency from the UPS meters in 0.1 Hz.
NUM upsESystemBypassVoltage	1.3.6.1.4.1.935.10.1.1.2.20.1.3	NonNegativeInteger	read-only	The measured bypass voltage from the UPS meters in 0.1 volts
NUM upsESystemBypassCurrent	1.3.6.1.4.1.935.10.1.1.2.20.1.4	NonNegativeInteger	read-only	The measured bypass mandatory from the UPS meters in 0.1 amps
NUM upsESystemBypassWatts	1.3.6.1.4.1.935.10.1.1.2.20.1.5	NonNegativeInteger	read-only	The measured input real power in watts.
NUM upsESystemConfigBelowCapacityLimit	1.3.6.1.4.1.935.10.1.1.2.21	NonNegativeInteger	read-write	The UPS batteries capacity(%) limit for shutdown
NUM upsESystemConfigBelowRemainTimeLimit	1.3.6.1.4.1.935.10.1.1.2.22	NonNegativeInteger	read-write	The UPS batteries backup time(minute) limit for shutdown
upsEBatterySystem	1.3.6.1.4.1.935.10.1.1.3
INT upsEBatteryStatus	1.3.6.1.4.1.935.10.1.1.3.1	INTEGER	read-only	The status of UPS battery, a value of batteryLow indicates that the battery-low status bit has been set from device. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is mandatoryly absent and the UPS is unable to sustain the output)
NUM upsESecondsOnBattery	1.3.6.1.4.1.935.10.1.1.3.2	NonNegativeInteger	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. 0 shall be returned if the unit is not on battery power
NUM upsEBatteryEstimatedMinutesRemaining	1.3.6.1.4.1.935.10.1.1.3.3	PositiveInteger	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.
I32 upsEBatteryEstimatedChargeRemaining	1.3.6.1.4.1.935.10.1.1.3.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge
NUM upsEPositiveBatteryVoltage	1.3.6.1.4.1.935.10.1.1.3.5	NonNegativeInteger	read-only	The magnitude of the present positive battery voltage in 0.1 Volt DC
NUM upsENegativeBatteryVoltage	1.3.6.1.4.1.935.10.1.1.3.6	NonNegativeInteger	read-only	The magnitude of the present negative battery voltage in 0.1 Volt DC
NUM upsEBatteryCellNumber	1.3.6.1.4.1.935.10.1.1.3.7	NonNegativeInteger	read-only	This object indicate the cell number of each set.
INT upsEBatteryTemperature	1.3.6.1.4.1.935.10.1.1.3.8	INTEGER	read-only	The ambient temperature at or near the UPS Battery casing in 0.1 degree.
STR upsEBatteryLastReplacedDate	1.3.6.1.4.1.935.10.1.1.3.9	DisplayString	read-only	The date when the Batteries in this UPS were last replaced. The format should be DD/MM/YYYY.
INT upsEBatteryABMStatus	1.3.6.1.4.1.935.10.1.1.3.10	INTEGER	read-only	The status of ABM.
NUM upsEChargerModulesNum	1.3.6.1.4.1.935.10.1.1.3.11	NonNegativeInteger	read-only	The number of charger modules inserted to UPS systems. served as the index of the upsEChargerModulesTable. The default value 0 indicate that the UPS system don't have separate charger module.
upsEChargerModulesTable	1.3.6.1.4.1.935.10.1.1.3.12		not-accessible	A list of charger modules entries. The number of entries is given by the value of upsEchargerModulesNum.
upsEChargerModulesEntry	1.3.6.1.4.1.935.10.1.1.3.12.1		not-accessible	An entry containing information applicable to a particular charger module.
NUM chargerModulesNum	1.3.6.1.4.1.935.10.1.1.3.12.1.1	PositiveInteger	not-accessible	The number of charger modules. Serves as index for charger module table
NUM chargerModulesAddress	1.3.6.1.4.1.935.10.1.1.3.12.1.2	NonNegativeInteger	read-only	Charger Modules' address.
NUM positiveChargeVotlage	1.3.6.1.4.1.935.10.1.1.3.12.1.3	NonNegativeInteger	read-only	The measured positive charger voltage from the UPS meters in 0.1 volts
NUM negativeChargeVoltage	1.3.6.1.4.1.935.10.1.1.3.12.1.4	NonNegativeInteger	read-only	The measured nepositive charger voltage from the UPS meters in 0.1 volts
NUM positiveChargeCurrent	1.3.6.1.4.1.935.10.1.1.3.12.1.5	NonNegativeInteger	read-only	The measured positive charger mandatory from the UPS meters in in 0.1 amps.
NUM negativeChargeCurrent	1.3.6.1.4.1.935.10.1.1.3.12.1.6	NonNegativeInteger	read-only	The measured nepositive charger mandatory from the UPS meters in 0.1 amps.
INT chargerModulesTemperature	1.3.6.1.4.1.935.10.1.1.3.12.1.7	INTEGER	read-only	The measured charger temperature from the UPS meters in 0.1 degree.
INT chargerModulesMode	1.3.6.1.4.1.935.10.1.1.3.12.1.8	INTEGER	read-only	The working mode of charger modules.
upsEPowerConverterSystem	1.3.6.1.4.1.935.10.1.1.4
NUM upsEUPSModulesNum	1.3.6.1.4.1.935.10.1.1.4.1	NonNegativeInteger	read-only	The number of UPS modules inserted to UPS systems. served as the index of the upsEModulesTable. the default value 0 indicate that the UPS system do not have separate UPS module.
upsEModulesTable	1.3.6.1.4.1.935.10.1.1.4.2		not-accessible	A list of UPS modules entries. The number of entries is given by the value of upsEModulesNum.
upsEModulesEntry	1.3.6.1.4.1.935.10.1.1.4.2.1		not-accessible	An entry containing information applicable to a particular upsE module.
NUM upsEModulesNum	1.3.6.1.4.1.935.10.1.1.4.2.1.1	PositiveInteger	not-accessible	The number of UPS modules. Serves as index for UPS module table
INT upsEModuleAddress	1.3.6.1.4.1.935.10.1.1.4.2.1.2	INTEGER	read-only	the address of UPS modules.
NUM upsEModulePositiveBusVolt	1.3.6.1.4.1.935.10.1.1.4.2.1.3	NonNegativeInteger	read-only	The measured positive upsE module voltage from the UPS meters in 0.1 volts
NUM upsEModuleNegativeBusVolt	1.3.6.1.4.1.935.10.1.1.4.2.1.4	NonNegativeInteger	read-only	The measured nepositive upsE module voltage from the UPS meters in 0.1 volts
INT upsEModuleTemperature	1.3.6.1.4.1.935.10.1.1.4.2.1.5	INTEGER	read-only	The measured upsE module temperature from the UPS meters in 0.1 degree.
INT upsEModuleWorkingMode	1.3.6.1.4.1.935.10.1.1.4.2.1.6	INTEGER	read-only	The working mode of UPS modules.
NUM upsEModuleOutputCurrentR	1.3.6.1.4.1.935.10.1.1.4.2.1.7	NonNegativeInteger	read-only	The measured upsE module output mandatory from the UPS meters in 0.1 A.
NUM upsEModuleOutputWattR	1.3.6.1.4.1.935.10.1.1.4.2.1.8	NonNegativeInteger	read-only	The measured upsE module output watts from the UPS meters in watts.
INT upsEModuleOutputLoadR	1.3.6.1.4.1.935.10.1.1.4.2.1.9	INTEGER	read-only	The output load of UPS modules in %.
STR upsEModuleWarningCode	1.3.6.1.4.1.935.10.1.1.4.2.1.10	DisplayString	read-only	The warning code of ups modules.Please refer the warning table of 'QU,XX' for details.
STR upsEModuleFaultCode	1.3.6.1.4.1.935.10.1.1.4.2.1.11	DisplayString	read-only	The fault code of ups modules.Please refer command 'QU,XX' for details.
STR upsEModuleTrapState	1.3.6.1.4.1.935.10.1.1.4.2.1.12	DisplayString	read-only	the values indicate the unrestored traps. For example, after AC fail, so the value of upsETrapState should be '1'. And then the AC restore, the value of upsEModuleTrapState should change to empty.
NUM upsEModuleConfigOutputVA	1.3.6.1.4.1.935.10.1.1.4.2.1.13	NonNegativeInteger	read-only	The magnitude of the nominal Volt-Amp rating presented in VA.
NUM upsEModuleOutputCurrentS	1.3.6.1.4.1.935.10.1.1.4.2.1.14	NonNegativeInteger	read-only	The measured upsE module output mandatory from the UPS meters in 0.1 A.
NUM upsEModuleOutputCurrentT	1.3.6.1.4.1.935.10.1.1.4.2.1.15	NonNegativeInteger	read-only	The measured upsE module output mandatory from the UPS meters in 0.1 A.
NUM upsEModuleOutputWattS	1.3.6.1.4.1.935.10.1.1.4.2.1.16	NonNegativeInteger	read-only	The measured upsE module output watts from the UPS meters in watts.
NUM upsEModuleOutputWattT	1.3.6.1.4.1.935.10.1.1.4.2.1.17	NonNegativeInteger	read-only	The measured upsE module output watts from the UPS meters in watts.
INT upsEModuleOutputLoadS	1.3.6.1.4.1.935.10.1.1.4.2.1.18	INTEGER	read-only	The output load of UPS modules in %.
INT upsEModuleOutputLoadT	1.3.6.1.4.1.935.10.1.1.4.2.1.19	INTEGER	read-only	The output load of UPS modules in %.
NUM upsEModuleOutputVAR	1.3.6.1.4.1.935.10.1.1.4.2.1.20	NonNegativeInteger	read-only	The magnitude of the nominal Volt-Amp rating presented in VA.
NUM upsEModuleOutputVAS	1.3.6.1.4.1.935.10.1.1.4.2.1.21	NonNegativeInteger	read-only	The magnitude of the nominal Volt-Amp rating presented in VA.
NUM upsEModuleOutputVAT	1.3.6.1.4.1.935.10.1.1.4.2.1.22	NonNegativeInteger	read-only	The magnitude of the nominal Volt-Amp rating presented in VA.
upsELoadSegment	1.3.6.1.4.1.935.10.1.1.5
INT upsELoadSegment1OffDelay	1.3.6.1.4.1.935.10.1.1.5.1	INTEGER	read-write	Setting this object will shutdown the UPS Load Segment output after the indicated number of seconds, or less. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. Read this object will get countdown value of the Load Segment.
INT upsELoadSegment1OnDelay	1.3.6.1.4.1.935.10.1.1.5.2	INTEGER	read-write	Setting this object will start the Load segment output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown.
INT upsELoadSegment1AutoOffTimer	1.3.6.1.4.1.935.10.1.1.5.3	INTEGER	read-write	The load segment turns automatically off after the delay while the unit operates on battery, but the shutdown is cancelled if the utility return before the delay has expired.
INT upsELoadSegment1AutoOnTimer	1.3.6.1.4.1.935.10.1.1.5.4	INTEGER	read-write	The load segment is automatically turned on after a selected delay if it has been shutdown due to on battery.
INT upsELoadSegment1State	1.3.6.1.4.1.935.10.1.1.5.5	INTEGER	read-only	Load segment output state.
INT upsELoadSegment2OffDelay	1.3.6.1.4.1.935.10.1.1.5.6	INTEGER	read-write	Setting this object will shutdown the UPS Load Segment output after the indicated number of seconds, or less. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. Read this object will get countdown value of the Load Segment.
INT upsELoadSegment2OnDelay	1.3.6.1.4.1.935.10.1.1.5.7	INTEGER	read-write	Setting this object will start the Load segment output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown.
INT upsELoadSegment2AutoOffTimer	1.3.6.1.4.1.935.10.1.1.5.8	INTEGER	read-write	The load segment turns automatically off after the delay while the unit operates on battery, but the shutdown is cancelled if the utility return before the delay has expired.
INT upsELoadSegment2AutoOnTimer	1.3.6.1.4.1.935.10.1.1.5.9	INTEGER	read-write	The load segment is automatically turned on after a selected delay if it has been shutdown due to on battery.
INT upsELoadSegment2State	1.3.6.1.4.1.935.10.1.1.5.10	INTEGER	read-only	Load segment output state.
upsEEnvironment	1.3.6.1.4.1.935.10.1.1.6
upsEEnvironmentTemperature	1.3.6.1.4.1.935.10.1.1.6.1
INT upsEEnvironmentCurrentTemperature	1.3.6.1.4.1.935.10.1.1.6.1.1	INTEGER	read-only	The measurement of temperature sensor, in 0.1 degree
INT upsEEnvironmentTemperatureHighSetPoint	1.3.6.1.4.1.935.10.1.1.6.1.2	INTEGER	read-write	The set point for high temperature warning, in 0.1 degrees. This value must be greater than upsEEnvironmentTemperatureLowSetPoint, and the least significant digit must be zero.
INT upsEEnvironmentTemperatureHighStatus	1.3.6.1.4.1.935.10.1.1.6.1.3	INTEGER	read-write	To enable/disable high set point check with sensor temperature.
INT upsEEnvironmentTemperatureLowSetPoint	1.3.6.1.4.1.935.10.1.1.6.1.4	INTEGER	read-write	The set point for low temperature warning, in 0.1 degrees. This value must be less than upsEEnvironmentTemperatureHighSetPoint, and the least significant digit must be zero.
INT upsEEnvironmentTemperatureLowStatus	1.3.6.1.4.1.935.10.1.1.6.1.5	INTEGER	read-write	To enable/disable low set point check with sensor temperature.
INT upsEEnvironmentTemperatureOffset	1.3.6.1.4.1.935.10.1.1.6.1.6	INTEGER	read-write	The offset to calibrate temperature of EMD, in 0.1 degrees
upsEEnvironmentHumidity	1.3.6.1.4.1.935.10.1.1.6.2
INT upsEEnvironmentCurrentHumidity	1.3.6.1.4.1.935.10.1.1.6.2.1	INTEGER	read-only	The measurement of sensor humidity present in %.
INT upsEEnvironmentHumidityHighSetPoint	1.3.6.1.4.1.935.10.1.1.6.2.2	INTEGER	read-write	The set point for high humidity warning, in %. This value must be greater than upsEEnvironmentHumidityLowSetPoint.
INT upsEEnvironmentHumidityHighStatus	1.3.6.1.4.1.935.10.1.1.6.2.3	INTEGER	read-write	To enable/disable high set point check with emd humidity.
INT upsEEnvironmentHumidityLowSetPoint	1.3.6.1.4.1.935.10.1.1.6.2.4	INTEGER	read-write	The set point for low humidity warning, in %. This value must be less than upsEEnvironmentHumidityHighSetPoint.
INT upsEEnvironmentHumidityLowStatus	1.3.6.1.4.1.935.10.1.1.6.2.5	INTEGER	read-write	To enable/disable high set point check with emd humidity.
INT upsEEnvironmentHumidityOffset	1.3.6.1.4.1.935.10.1.1.6.2.6	INTEGER	read-write	The offset to calibrate humidity of EMD, in %.
NUM upsEEnvironmentContactsNum	1.3.6.1.4.1.935.10.1.1.6.3	NonNegativeInteger	read-only	The number of environment contacts, serves as the table index.
upsEEnvironmentContactTable	1.3.6.1.4.1.935.10.1.1.6.4		not-accessible	A list of contacts table entries. The number of entries is given by the value of upsEEnvironmentContactsNum
upsEEnvironmentContactEntry	1.3.6.1.4.1.935.10.1.1.6.4.1		not-accessible	An entry containing information applicable to a particular contact
NUM upsEEnvironmentContactIndex	1.3.6.1.4.1.935.10.1.1.6.4.1.1	PositiveInteger	not-accessible	The number of environment contacts. Serves as index for environment contact table
INT upsEEnvironmentContactType	1.3.6.1.4.1.935.10.1.1.6.4.1.2	INTEGER	read-write	operation type
INT upsEEnvironmentContactState	1.3.6.1.4.1.935.10.1.1.6.4.1.3	INTEGER	read-only	The mandatory status.
STR upsEEnvironmentContactDescription	1.3.6.1.4.1.935.10.1.1.6.4.1.4	DisplayString	read-write	Description of environment contact.
upsEBatteryTest	1.3.6.1.4.1.935.10.1.1.7
INT upsEBatteryTestStart	1.3.6.1.4.1.935.10.1.1.7.1	INTEGER	read-write	This object specify the battery test type and initiate battery test. If battTestWithTime selected, the test time is refer to upsEBatteryTestSettingTime.
NUM upsEBatteryTestSettingTime	1.3.6.1.4.1.935.10.1.1.7.2	NonNegativeInteger	read-write	The object specify the test time for battery test in seconds.
INT upsEBatteryTestResult	1.3.6.1.4.1.935.10.1.1.7.3	INTEGER	read-only	This object indicate the test result of battery.
STR upsEBatteryTestStartTime	1.3.6.1.4.1.935.10.1.1.7.4	DisplayString	read-only	The value of the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsETestBatteryTestResult is noTestsInitiated(6), upsETestStartTime has the value 01/01/1970 00:00:00.
STR upsEBatteryTestElapsedTime	1.3.6.1.4.1.935.10.1.1.7.5	DisplayString	read-only	The amount of time in format hh:mm:ss, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is idle(1), upsTestElapsedTime has the value 00:00:00.
upsEBatteryTestScheduleTable	1.3.6.1.4.1.935.10.1.1.7.6		not-accessible	This table describes the schedule for automatically battery test.
upsEBatteryTestScheduleEntry	1.3.6.1.4.1.935.10.1.1.7.6.1		not-accessible	An entry containing information applicable to schedule test.
NUM upsEBatteryTestScheduleIndex	1.3.6.1.4.1.935.10.1.1.7.6.1.1	PositiveInteger	not-accessible	The index of battery test scheduled.
INT upsEBatteryTestScheduleDay	1.3.6.1.4.1.935.10.1.1.7.6.1.2	INTEGER	read-write	The weekday or specaial day on which the UPS should start battery test.
STR upsEBatteryTestScheduleTime	1.3.6.1.4.1.935.10.1.1.7.6.1.3	DisplayString	read-write	The time that the battery test will be initiated in hh:mm format.
INT upsEBatteryTestScheduleType	1.3.6.1.4.1.935.10.1.1.7.6.1.5	INTEGER	read-write	The type of battery test.
NUM upsEBatteryTestScheduleTestWithTime	1.3.6.1.4.1.935.10.1.1.7.6.1.6	NonNegativeInteger	read-write	The battery time of setting time test in seconds.
STR upsEBatteryTestScheduleSpecialDay	1.3.6.1.4.1.935.10.1.1.7.6.1.7	DisplayString	read-write	The special day that the battery test will be initiated in dd/mm/yyyy format.
upsEControl	1.3.6.1.4.1.935.10.1.1.8
NUM upsEControlOutputOffDelay	1.3.6.1.4.1.935.10.1.1.8.1	NonNegativeInteger	read-write	Setting this value to other than zero will cause the UPS output to turn off after the number of seconds.
NUM upsEControlOutputOnDelay	1.3.6.1.4.1.935.10.1.1.8.2	NonNegativeInteger	read-write	Setting this value to other than zero will cause the UPS output to turn on after the number of seconds.
INT upsEControlOutputOnOffControl	1.3.6.1.4.1.935.10.1.1.8.3	INTEGER	read-write	upsEOutputOff ( 1 ) indicates the shutdown sequence, upsEOutputOffCancel ( 2 ) indicates cancel the shutdown sequence, upsESleep( 3 ) indicates shutdown UPS first, then switch on.
upsEShutdownEventsTable	1.3.6.1.4.1.935.10.1.1.8.4		not-accessible	This table describes the parametes for shutdown process when shutdown event occurs
upsEShutdownEventsEntry	1.3.6.1.4.1.935.10.1.1.8.4.1		not-accessible	An entry containing information applicable to a particular shutdown event line
INT upsEShutdownEvent	1.3.6.1.4.1.935.10.1.1.8.4.1.1	INTEGER	not-accessible	The shutdown event identification
INT upsEShutdownEventAction	1.3.6.1.4.1.935.10.1.1.8.4.1.2	INTEGER	read-write	Status of the corresponding shutdown Event. When set to disable(), shutdown process will not start when corresponding event occured.
NUM upsEShutdownwarningPeriodTime	1.3.6.1.4.1.935.10.1.1.8.4.1.3	NonNegativeInteger	read-write	The Delay in seconds after the occurance of the curresponding shutdown event, and warning message should be popped in this period.
NUM upsEShutdownWarningPeriodInterval	1.3.6.1.4.1.935.10.1.1.8.4.1.4	NonNegativeInteger	read-write	The frequency of sending warning messages to the connected clients when the curresponding shutdown event occurs. The value is in units of seconds.
upsEControlWeeklyScheduleTable	1.3.6.1.4.1.935.10.1.1.8.5		not-accessible	The table to schedule shutting down the ups by weekly
upsEControlWeeklyScheduleEntry	1.3.6.1.4.1.935.10.1.1.8.5.1		not-accessible	An entry containing information applicable to a particular line
NUM upsEControlWeeklyScheduleIndex	1.3.6.1.4.1.935.10.1.1.8.5.1.1	PositiveInteger	not-accessible	the index of schedule events.
INT upsEWeeklyScheduleShutdownDay	1.3.6.1.4.1.935.10.1.1.8.5.1.2	INTEGER	read-write	the weekday on which upsE shoud shutdown
STR upsEWeeklyScheduleShutdownTime	1.3.6.1.4.1.935.10.1.1.8.5.1.3	DisplayString	read-write	The time that the process of shutting down the UPS will be initiated in hh:mm format.
INT upsEWeeklyScheduleRestartDay	1.3.6.1.4.1.935.10.1.1.8.5.1.4	INTEGER	read-write	the weekday on which the UPS should restart.
STR upsEWeeklyScheduleRestartTime	1.3.6.1.4.1.935.10.1.1.8.5.1.5	DisplayString	read-write	The time the UPS will restart in hh:mm format.
upsEControlSpecialDayScheduleTable	1.3.6.1.4.1.935.10.1.1.8.6		not-accessible	The table to schedule shutting down the ups.
upsEControlSpecialDayScheduleEntry	1.3.6.1.4.1.935.10.1.1.8.6.1		not-accessible	An entry containing information applicable to a particular line.
NUM upsEControlSpecialDayScheduleIndex	1.3.6.1.4.1.935.10.1.1.8.6.1.1	PositiveInteger	not-accessible	The index of special day schedule.
STR upsESpecialDayScheduleShutdownDay	1.3.6.1.4.1.935.10.1.1.8.6.1.2	DisplayString	read-write	The special day on which UPS should shutdown with the format of DD/MM/YYYY.
STR upsESpecialDayScheduleShutdownTime	1.3.6.1.4.1.935.10.1.1.8.6.1.3	DisplayString	read-write	The time that the process of shutting down the UPS will be initiated in hh:mm format.
STR upsESpecialDayScheduleRestartDay	1.3.6.1.4.1.935.10.1.1.8.6.1.4	DisplayString	read-write	The special day on which the UPS should restart with the format of DD/MM/YYYY.
STR upsESpecialDayScheduleRestartTime	1.3.6.1.4.1.935.10.1.1.8.6.1.5	DisplayString	read-write	The time the UPS will restart in hh:mm format.
INT upsESystemMasterOffDelay	1.3.6.1.4.1.935.10.1.1.8.7	INTEGER	read-only	The UPS output will shutdown after the indicated number of seconds, -1 indicate no action.
INT upsESystemMasterOnDelay	1.3.6.1.4.1.935.10.1.1.8.8	INTEGER	read-only	The UPS output will start on after the indicated number of seconds, -1 indicate no action.
upsETrapControl	1.3.6.1.4.1.935.10.1.1.9
upsETrapsReceiversTable	1.3.6.1.4.1.935.10.1.1.9.1		not-accessible	This table list the managers'IP to send traps to.
upsETrapsReceiversEntry	1.3.6.1.4.1.935.10.1.1.9.1.1		not-accessible	An entry containing information applicable to a particular input line.
NUM upsETrapsReceiversIndex	1.3.6.1.4.1.935.10.1.1.9.1.1.1	PositiveInteger	not-accessible	The index to a trap receiver entry
STR upsETrapsReceiverAddress	1.3.6.1.4.1.935.10.1.1.9.1.1.2	DisplayString	read-write	The IP address of the manager to send a trap to.
STR upsETrapReceiverCommunityString	1.3.6.1.4.1.935.10.1.1.9.1.1.3	DisplayString	read-write	The community name to use in the trap when sent to the manager.
INT upsETrapType	1.3.6.1.4.1.935.10.1.1.9.1.1.4	INTEGER	read-write	The type of trap to be received by the manager.
INT upsETrapsSeverityLevel	1.3.6.1.4.1.935.10.1.1.9.1.1.5	INTEGER	read-write	The severity level of traps to be received by this manager.
STR upsETrapReceiverDescription	1.3.6.1.4.1.935.10.1.1.9.1.1.6	DisplayString	read-write	Description of trap receivers
STR upsETrapState	1.3.6.1.4.1.935.10.1.1.9.2	DisplayString	read-only	the values indicate the unrestored traps. For example, after AC fail, the agent send the trap 1(AC Fail) and trap 7(battery on) to NMS. so the value of upsETrapState should be '1,7'. And then the AC restore, the value of upsETrapState should change to empty.
upsETraps	1.3.6.1.4.1.935.10.1.2
NTF upsEPowerFail	1.3.6.1.4.1.935.10.1.2.0.1			WARNING: Utility power not available.
NTF upsEPowerRestored	1.3.6.1.4.1.935.10.1.2.0.2			INFORMATION: Utility power has restored.
NTF upsELowBattery	1.3.6.1.4.1.935.10.1.2.0.3			SEVERE: The UPS batteries are low and will soon be exhausted.
NTF upsEReturnFromLowBattery	1.3.6.1.4.1.935.10.1.2.0.4			INFORMATION: The UPS has return from a low battery condition.
NTF upsEFailed	1.3.6.1.4.1.935.10.1.2.0.5			SEVERE: The UPS is not working fine.
NTF upsEOk	1.3.6.1.4.1.935.10.1.2.0.6			INFORMATION: The UPS is working fine.
NTF upsEOnBattery	1.3.6.1.4.1.935.10.1.2.0.7			WARNING: The UPS has switched to battery backup power.
NTF upsENotOnBattery	1.3.6.1.4.1.935.10.1.2.0.8			INFORMATION: The UPS is not on battery power.
NTF upsETestInProgress	1.3.6.1.4.1.935.10.1.2.0.9			INFORMATION: The testing is going on ups.
NTF upsETestOver	1.3.6.1.4.1.935.10.1.2.0.10			INFORMATION: The testing of UPS is completed.
NTF upsEBypassOn	1.3.6.1.4.1.935.10.1.2.0.11			INFORMATION: The UPS has enabled bypass.
NTF upsEOnline	1.3.6.1.4.1.935.10.1.2.0.12			INFORMATION: The UPS is not on Bypass and return to normal status.
NTF upsECommunicationLost	1.3.6.1.4.1.935.10.1.2.0.13			SEVERE: Communication to the UPS has been lost.
NTF upsECommunicationEstablished	1.3.6.1.4.1.935.10.1.2.0.14			INFORMATION: Communication with the UPS has been established.
NTF upsEGoingShutdown	1.3.6.1.4.1.935.10.1.2.0.15			WARNING: The UPS is going to shutdown output.
NTF upsEShutdownCancelled	1.3.6.1.4.1.935.10.1.2.0.16			INFORMATION: The UPS is not going to shutdown output.
NTF upsEOutlet1GoingShutdown	1.3.6.1.4.1.935.10.1.2.0.17			WARNING: The UPS is going to shutdown outlet1.
NTF upsEOutlet1ShutdownCancelled	1.3.6.1.4.1.935.10.1.2.0.18			INFORMATION: The UPS is not going to shutdown outlet1.
NTF upsEOutlet2GoingShutdown	1.3.6.1.4.1.935.10.1.2.0.19			WARNING: The UPS is going to shutdown outlet2.
NTF upsEOutlet2ShutdownCancelled	1.3.6.1.4.1.935.10.1.2.0.20			INFORMATION: The UPS is not going to shutdown outlet2.
NTF upsESleeping	1.3.6.1.4.1.935.10.1.2.0.21			INFORMATION: UPS has entered sleep mode and power to load has been cut off.
NTF upsEWokeUp	1.3.6.1.4.1.935.10.1.2.0.22			INFORMATION: The UPS woke up from sleep mode and power to load has been restored.
NTF upsEOverTemperature	1.3.6.1.4.1.935.10.1.2.0.23			WARNING: The UPS temperature is over the setting limit.
NTF upsENotOverTemperature	1.3.6.1.4.1.935.10.1.2.0.24			INFORMATION: The UPS temperature is not over the setting limit.
NTF upsEOverLoad	1.3.6.1.4.1.935.10.1.2.0.25			WARNING: The UPS load is over the setting limit.
NTF upsENotOverLoad	1.3.6.1.4.1.935.10.1.2.0.26			INFORMATION: The UPS load is not over the setting limit.
NTF upsEModuleInserted	1.3.6.1.4.1.935.10.1.2.0.27			WARNING: UPS module or charger module plug-in.
NTF upsEModuleRemoved	1.3.6.1.4.1.935.10.1.2.0.28			WARNING: UPS module or charger module unplugs.
NTF sensorTemperatureTooHigh	1.3.6.1.4.1.935.10.1.2.0.29			WARNING: Sensor Temperature over high Set point.
NTF sensorTemperatureNotHigh	1.3.6.1.4.1.935.10.1.2.0.30			INFORMATION: Sensor Temperature not over high Set point.
NTF sensorTemperatureTooLow	1.3.6.1.4.1.935.10.1.2.0.31			WARNING: Sensor Temperature under low Set point.
NTF sensorTemperatureNotLow	1.3.6.1.4.1.935.10.1.2.0.32			INFORMATION: Sensor Temperature not under low Set point.
NTF sensorHumidityTooHigh	1.3.6.1.4.1.935.10.1.2.0.33			WARNING: Sensor Humidity over high Set point.
NTF sensorHumidityNotHigh	1.3.6.1.4.1.935.10.1.2.0.34			INFORMATION: Sensor Humidity not over high Set point.
NTF sensorHumidityTooLow	1.3.6.1.4.1.935.10.1.2.0.35			WARNING: Sensor Humidity under low Set point.
NTF sensorHumidityNotLow	1.3.6.1.4.1.935.10.1.2.0.36			INFORMATION: Sensor Humidity not under low Set point.
NTF contactAlarm1Active	1.3.6.1.4.1.935.10.1.2.0.37			WARNING: Contact Alarm-1 activated.
NTF concactAlarm1Normal	1.3.6.1.4.1.935.10.1.2.0.38			INFORMATION: Contact Alarm-1 not active.
NTF contactAlarm2Active	1.3.6.1.4.1.935.10.1.2.0.39			WARNING: Contact Alarm-2 activated.
NTF contactAlarm2Normal	1.3.6.1.4.1.935.10.1.2.0.40			INFORMATION: Contact Alarm-2 not active.
NTF upsEInternalwarning	1.3.6.1.4.1.935.10.1.2.0.41			WARNING: Internal warning.
NTF upsEReturnFromInternalwarning	1.3.6.1.4.1.935.10.1.2.0.42			INFORMATION: Return from Internal warning.
NTF upsEEPOActive	1.3.6.1.4.1.935.10.1.2.0.43			WARNING: EPO Active.
NTF upsEReturnFromEPOActive	1.3.6.1.4.1.935.10.1.2.0.44			INFORMATION: Return from EPO Active.
NTF upsEModuleUnlock	1.3.6.1.4.1.935.10.1.2.0.45			WARNING: Module Unlock.
NTF upsEReturnFromModuleUnlock	1.3.6.1.4.1.935.10.1.2.0.46			INFORMATION: Return from Module Unlock.
NTF upsEMain1Neutralloss	1.3.6.1.4.1.935.10.1.2.0.47			WARNING: Main 1 Neutral loss.
NTF upsEReturnFromMain1Neutralloss	1.3.6.1.4.1.935.10.1.2.0.48			INFORMATION: Return from Main 1 Neutral loss.
NTF upsEMain1phaseerror	1.3.6.1.4.1.935.10.1.2.0.49			WARNING: Main 1 phase error.
NTF upsEReturnFromMain1phaseerror	1.3.6.1.4.1.935.10.1.2.0.50			INFORMATION: Return from Main 1 phase error.
NTF upsESitefault	1.3.6.1.4.1.935.10.1.2.0.51			WARNING: Site fault.
NTF upsEReturnFromSitefault	1.3.6.1.4.1.935.10.1.2.0.52			INFORMATION: Return from Site fault.
NTF upsEBypassAbnormal	1.3.6.1.4.1.935.10.1.2.0.53			WARNING: Bypass Abnormal.
NTF upsEReturnFromBypassAbnormal	1.3.6.1.4.1.935.10.1.2.0.54			INFORMATION: Return from Bypass Abnormal.
NTF upsEBypassPhaseError	1.3.6.1.4.1.935.10.1.2.0.55			WARNING: Bypass Phase Error.
NTF upsEReturnFromBypassPhaseError	1.3.6.1.4.1.935.10.1.2.0.56			INFORMATION: Return from Bypass Phase Error.
NTF upsEBatteryOpen	1.3.6.1.4.1.935.10.1.2.0.57			WARNING: Battery Open.
NTF upsEReturnFromBatteryOpen	1.3.6.1.4.1.935.10.1.2.0.58			INFORMATION: Return from Battery Open.
NTF upsEBatteryOverCharge	1.3.6.1.4.1.935.10.1.2.0.59			WARNING: Battery Over Charge.
NTF upsEReturnFromBatteryOverCharge	1.3.6.1.4.1.935.10.1.2.0.60			INFORMATION: Return from Battery Over Charge.
NTF upsEBatteryReverse	1.3.6.1.4.1.935.10.1.2.0.61			WARNING: Battery Reverse.
NTF upsEReturnFromBatteryReverse	1.3.6.1.4.1.935.10.1.2.0.62			INFORMATION: Return from Battery Reverse.
NTF upsEOverloadforewarning	1.3.6.1.4.1.935.10.1.2.0.63			WARNING: Overload forewarning.
NTF upsEReturnFromOverloadforewarning	1.3.6.1.4.1.935.10.1.2.0.64			INFORMATION: Return from Overload forewarning.
NTF upsEOverloadWarning	1.3.6.1.4.1.935.10.1.2.0.65			WARNING: Overload Warning.
NTF upsEReturnFromOverloadWarning	1.3.6.1.4.1.935.10.1.2.0.66			INFORMATION: Return from Overload Warning.
NTF upsEFanLock	1.3.6.1.4.1.935.10.1.2.0.67			WARNING: Fan Lock.
NTF upsEReturnFromFanLock	1.3.6.1.4.1.935.10.1.2.0.68			INFORMATION: Return from Fan Lock.
NTF upsEMaintaincoverisopen	1.3.6.1.4.1.935.10.1.2.0.69			WARNING: Maintain cover is open.
NTF upsEReturnFromMaintaincoverisopen	1.3.6.1.4.1.935.10.1.2.0.70			INFORMATION: Return from Maintain cover is open.
NTF upsEChargerfault	1.3.6.1.4.1.935.10.1.2.0.71			WARNING: Charger fault.
NTF upsEReturnFromChargerfault	1.3.6.1.4.1.935.10.1.2.0.72			INFORMATION: Return from Charger fault.
NTF upsEModulelocationerror	1.3.6.1.4.1.935.10.1.2.0.73			WARNING: Module location error.
NTF upsEReturnFromModulelocationerror	1.3.6.1.4.1.935.10.1.2.0.74			INFORMATION: Return from Module location error.
NTF upsETurnonabnormal	1.3.6.1.4.1.935.10.1.2.0.75			WARNING: Turn on abnormal.
NTF upsEReturnFromTurnonabnormal	1.3.6.1.4.1.935.10.1.2.0.76			INFORMATION: Return from Turn on abnormal.
NTF upsERedundancyloss	1.3.6.1.4.1.935.10.1.2.0.77			WARNING: Redundancy loss.
NTF upsEReturnFromRedundancyloss	1.3.6.1.4.1.935.10.1.2.0.78			INFORMATION: Return from Redundancy loss.
NTF upsEHotSwapActived	1.3.6.1.4.1.935.10.1.2.0.79			WARNING: Hot Swap Active.
NTF upsEReturnFromHotSwapActived	1.3.6.1.4.1.935.10.1.2.0.80			INFORMATION: Return from Hot Swap Active.
NTF upsEBatteryInform	1.3.6.1.4.1.935.10.1.2.0.81			WARNING: Battery Inform.
NTF upsEReturnFromBatteryInform	1.3.6.1.4.1.935.10.1.2.0.82			INFORMATION: Return from Battery Inform.
NTF upsEInspectionInform	1.3.6.1.4.1.935.10.1.2.0.83			WARNING: Inspection Inform.
NTF upsEReturnFromInspectionInform	1.3.6.1.4.1.935.10.1.2.0.84			INFORMATION: Return from Inspection Inform.
NTF upsEGuaranteeInform	1.3.6.1.4.1.935.10.1.2.0.85			WARNING: Guarantee Inform.
NTF upsEReturnFromGuaranteeInform	1.3.6.1.4.1.935.10.1.2.0.86			INFORMATION: Return from Guarantee Inform.
NTF upsETemperatureLow	1.3.6.1.4.1.935.10.1.2.0.87			WARNING: Temperature Low.
NTF upsEReturnFromTemperatureLow	1.3.6.1.4.1.935.10.1.2.0.88			INFORMATION: Return from Temperature Low.
NTF upsETemperatureHigh	1.3.6.1.4.1.935.10.1.2.0.89			WARNING: Temperature High.
NTF upsEReturnFromTemperatureHigh	1.3.6.1.4.1.935.10.1.2.0.90			INFORMATION: Return from Temperature High.
NTF upsEBatteryOverTemperature	1.3.6.1.4.1.935.10.1.2.0.91			WARNING: Battery Over Temperature.
NTF upsEReturnFromBatteryOverTemperature	1.3.6.1.4.1.935.10.1.2.0.92			INFORMATION: Return from Battery Over Temperature.
NTF upsEFanMaintainInform	1.3.6.1.4.1.935.10.1.2.0.93			WARNING: Fan Maintain Inform.
NTF upsEReturnFromFanMaintainInform	1.3.6.1.4.1.935.10.1.2.0.94			INFORMATION: Return from Fan Maintain Inform.
NTF upsEBusCapacitanceMaintainInform	1.3.6.1.4.1.935.10.1.2.0.95			WARNING: Bus Capacitance Maintain Inform.
NTF upsEReturnFromBusCapacitanceMaintainInform	1.3.6.1.4.1.935.10.1.2.0.96			INFORMATION: Return from Bus Capacitance Maintain Inform.
NTF upsESystemOverCapacity	1.3.6.1.4.1.935.10.1.2.0.97			WARNING: System Over Capacity.
NTF upsEReturnFromSystemOverCapacity	1.3.6.1.4.1.935.10.1.2.0.98			INFORMATION: Return from System Over Capacity.
NTF upsEBelowCapacityLimit	1.3.6.1.4.1.935.10.1.2.0.123			SEVERE: The UPS batteries capacity is lower than setting limit.
NTF upsENotBelowCapacityLimit	1.3.6.1.4.1.935.10.1.2.0.124			INFORMATION: The UPS batteries capacity is not lower than setting limit.
NTF upsEBelowRemainTimeLimit	1.3.6.1.4.1.935.10.1.2.0.125			SEVERE: The UPS batteries backup time is below the setting limit.
NTF upsENotBelowRemainTimeLimit	1.3.6.1.4.1.935.10.1.2.0.126			INFORMATION: The UPS batteries backup time is not below the setting limit.
NTF upsELoadSegment1Off	1.3.6.1.4.1.935.10.1.2.0.127			WARNING: Load segment 1 is off.
NTF upsELoadSegment1On	1.3.6.1.4.1.935.10.1.2.0.128			INFORMATION: Load segment 1 is on.
NTF upsELoadSegment2Off	1.3.6.1.4.1.935.10.1.2.0.129			WARNING: Load segment 2 is off.
NTF upsELoadSegment2On	1.3.6.1.4.1.935.10.1.2.0.130			INFORMATION: Load segment 2 is on.

RFC description

UPS system MIB for managing uninterruptible power supplies, including battery, power converter, load segment, environmental monitoring, and battery testing.

Start monitoring Three-phase UPS system with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download EPPC-MIB

What Is EPPC-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description