GEPARALLELUPS-MIB

OID symbolic	OID numeric	Type	Access	Description
imv	1.3.6.1.4.1.818			The MIB module to describe GE Digital Energy Uninterruptible Power Supplies.
geHardware	1.3.6.1.4.1.818.1
geUPS	1.3.6.1.4.1.818.1.1
I32 geDiscoveredUPSsMask	1.3.6.1.4.1.818.1.1.1	Integer32	read-only	Reading this variable returns bit mask indicating which UPSs in a parallel system are alive. Management software should poll only these UPSs on their snmp branches 11-18 as follows: 1 FirstUPS alive 2 SecondUPS alive 4 ThirdUPS alive 8 FourthUPS alive 16 FifthUPS alive 32 SixthUPS alive 64 SeventhUPS alive 128 EigthUPS alive Since the management software should always monitor the GenericUPS branch (10), this value has no meaning for single upses (which provide values on that snmp branch), and should be set to zero in that case.
STR geRequestPacket	1.3.6.1.4.1.818.1.1.2	DisplayString	read-write	Put the string, formatted as a IMV/CP4 packet, directly to internally RS485 bus. This OID could be used for accede directly to the internally RS485 bus from a remote place.
STR geReplyPacket	1.3.6.1.4.1.818.1.1.3	DisplayString	read-only	Contain the reply of the IMV/CP4 request packet sent using the OID geRequestPacket. Every time that a write command has be made at the OID ge RequestPacket, the value of this OID is erased.
geGenericUPS	1.3.6.1.4.1.818.1.1.10
upsIdent	1.3.6.1.4.1.818.1.1.10.1
STR upsIdentManufacturer	1.3.6.1.4.1.818.1.1.10.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel	1.3.6.1.4.1.818.1.1.10.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion	1.3.6.1.4.1.818.1.1.10.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion	1.3.6.1.4.1.818.1.1.10.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName	1.3.6.1.4.1.818.1.1.10.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices	1.3.6.1.4.1.818.1.1.10.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber	1.3.6.1.4.1.818.1.1.10.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion	1.3.6.1.4.1.818.1.1.10.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime	1.3.6.1.4.1.818.1.1.10.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery	1.3.6.1.4.1.818.1.1.10.2
INT upsBatteryStatus	1.3.6.1.4.1.818.1.1.10.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
I32 upsSecondsOnBattery	1.3.6.1.4.1.818.1.1.10.2.2	Integer32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining	1.3.6.1.4.1.818.1.1.10.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining	1.3.6.1.4.1.818.1.1.10.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage	1.3.6.1.4.1.818.1.1.10.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent	1.3.6.1.4.1.818.1.1.10.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature	1.3.6.1.4.1.818.1.1.10.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
I32 upsBatteryRipple	1.3.6.1.4.1.818.1.1.10.2.8	Integer32	read-only	The present DC link RMS voltage ripple.(*)
upsInput	1.3.6.1.4.1.818.1.1.10.3
C32 upsInputLineBadsEx	1.3.6.1.4.1.818.1.1.10.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines	1.3.6.1.4.1.818.1.1.10.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable	1.3.6.1.4.1.818.1.1.10.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry	1.3.6.1.4.1.818.1.1.10.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex	1.3.6.1.4.1.818.1.1.10.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency	1.3.6.1.4.1.818.1.1.10.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage	1.3.6.1.4.1.818.1.1.10.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent	1.3.6.1.4.1.818.1.1.10.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower	1.3.6.1.4.1.818.1.1.10.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin	1.3.6.1.4.1.818.1.1.10.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax	1.3.6.1.4.1.818.1.1.10.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput	1.3.6.1.4.1.818.1.1.10.4
INT upsOutputSource	1.3.6.1.4.1.818.1.1.10.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency	1.3.6.1.4.1.818.1.1.10.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines	1.3.6.1.4.1.818.1.1.10.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable	1.3.6.1.4.1.818.1.1.10.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry	1.3.6.1.4.1.818.1.1.10.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex	1.3.6.1.4.1.818.1.1.10.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage	1.3.6.1.4.1.818.1.1.10.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent	1.3.6.1.4.1.818.1.1.10.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower	1.3.6.1.4.1.818.1.1.10.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad	1.3.6.1.4.1.818.1.1.10.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
I32 upsOutputPowerFactor	1.3.6.1.4.1.818.1.1.10.4.4.1.6	Integer32	read-only	The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)
I32 upsOutputPeakCurrent	1.3.6.1.4.1.818.1.1.10.4.4.1.7	Integer32	read-only	The present output peak current.(*)
I32 upsOutputShareCurrent	1.3.6.1.4.1.818.1.1.10.4.4.1.8	Integer32	read-only	In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)
upsBypass	1.3.6.1.4.1.818.1.1.10.5
NUM upsBypassFrequency	1.3.6.1.4.1.818.1.1.10.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines	1.3.6.1.4.1.818.1.1.10.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable	1.3.6.1.4.1.818.1.1.10.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry	1.3.6.1.4.1.818.1.1.10.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex	1.3.6.1.4.1.818.1.1.10.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage	1.3.6.1.4.1.818.1.1.10.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent	1.3.6.1.4.1.818.1.1.10.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower	1.3.6.1.4.1.818.1.1.10.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm	1.3.6.1.4.1.818.1.1.10.6
G32 upsAlarmsPresent	1.3.6.1.4.1.818.1.1.10.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable	1.3.6.1.4.1.818.1.1.10.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry	1.3.6.1.4.1.818.1.1.10.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId	1.3.6.1.4.1.818.1.1.10.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr	1.3.6.1.4.1.818.1.1.10.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime	1.3.6.1.4.1.818.1.1.10.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms	1.3.6.1.4.1.818.1.1.10.6.3
upsAlarmBatteryBad	1.3.6.1.4.1.818.1.1.10.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery	1.3.6.1.4.1.818.1.1.10.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery	1.3.6.1.4.1.818.1.1.10.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery	1.3.6.1.4.1.818.1.1.10.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad	1.3.6.1.4.1.818.1.1.10.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad	1.3.6.1.4.1.818.1.1.10.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad	1.3.6.1.4.1.818.1.1.10.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload	1.3.6.1.4.1.818.1.1.10.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass	1.3.6.1.4.1.818.1.1.10.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad	1.3.6.1.4.1.818.1.1.10.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested	1.3.6.1.4.1.818.1.1.10.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested	1.3.6.1.4.1.818.1.1.10.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed	1.3.6.1.4.1.818.1.1.10.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff	1.3.6.1.4.1.818.1.1.10.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff	1.3.6.1.4.1.818.1.1.10.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure	1.3.6.1.4.1.818.1.1.10.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure	1.3.6.1.4.1.818.1.1.10.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault	1.3.6.1.4.1.818.1.1.10.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed	1.3.6.1.4.1.818.1.1.10.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost	1.3.6.1.4.1.818.1.1.10.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower	1.3.6.1.4.1.818.1.1.10.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending	1.3.6.1.4.1.818.1.1.10.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent	1.3.6.1.4.1.818.1.1.10.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress	1.3.6.1.4.1.818.1.1.10.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff	1.3.6.1.4.1.818.1.1.10.6.3.25			The receptacle are switch off
upsAlarmHighSpeedBusFailure	1.3.6.1.4.1.818.1.1.10.6.3.26			A problem on the High Speed Bus communication is detected
upsAlarmHighSpeedBusJACRCFailure	1.3.6.1.4.1.818.1.1.10.6.3.27			A CRC problem on the Highspeed Bus JA is detected.
upsAlarmConnectivityBusFailure	1.3.6.1.4.1.818.1.1.10.6.3.28			A problem on the Connectivity Bus communication is detected
upsAlarmHighSpeedBusJBCRCFailure	1.3.6.1.4.1.818.1.1.10.6.3.29			A CRC problem on the Highspeed Bus JB is detected.
upsAlarmCurrentSharing	1.3.6.1.4.1.818.1.1.10.6.3.30			The System detects an high current sharing on the parallel system
upsAlarmDCRipple	1.3.6.1.4.1.818.1.1.10.6.3.31			The System detects an high ripple voltage on one DC link
U32 upsAlarmMaskA	1.3.6.1.4.1.818.1.1.10.6.4	Unsigned32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest	1.3.6.1.4.1.818.1.1.10.7
OID upsTestId	1.3.6.1.4.1.818.1.1.10.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock	1.3.6.1.4.1.818.1.1.10.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto tryagain } if (errorindex == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lockvalue + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary	1.3.6.1.4.1.818.1.1.10.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail	1.3.6.1.4.1.818.1.1.10.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime	1.3.6.1.4.1.818.1.1.10.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime	1.3.6.1.4.1.818.1.1.10.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests	1.3.6.1.4.1.818.1.1.10.7.7
upsTestNoTestsInitiated	1.3.6.1.4.1.818.1.1.10.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress	1.3.6.1.4.1.818.1.1.10.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest	1.3.6.1.4.1.818.1.1.10.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest	1.3.6.1.4.1.818.1.1.10.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration	1.3.6.1.4.1.818.1.1.10.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl	1.3.6.1.4.1.818.1.1.10.8
INT upsShutdownType	1.3.6.1.4.1.818.1.1.10.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay	1.3.6.1.4.1.818.1.1.10.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay	1.3.6.1.4.1.818.1.1.10.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration	1.3.6.1.4.1.818.1.1.10.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart	1.3.6.1.4.1.818.1.1.10.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum	1.3.6.1.4.1.818.1.1.10.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable	1.3.6.1.4.1.818.1.1.10.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry	1.3.6.1.4.1.818.1.1.10.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex	1.3.6.1.4.1.818.1.1.10.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff	1.3.6.1.4.1.818.1.1.10.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode	1.3.6.1.4.1.818.1.1.10.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff	1.3.6.1.4.1.818.1.1.10.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod	1.3.6.1.4.1.818.1.1.10.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff	1.3.6.1.4.1.818.1.1.10.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff	1.3.6.1.4.1.818.1.1.10.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource	1.3.6.1.4.1.818.1.1.10.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig	1.3.6.1.4.1.818.1.1.10.9
NUM upsConfigInputVoltage	1.3.6.1.4.1.818.1.1.10.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq	1.3.6.1.4.1.818.1.1.10.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage	1.3.6.1.4.1.818.1.1.10.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq	1.3.6.1.4.1.818.1.1.10.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA	1.3.6.1.4.1.818.1.1.10.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower	1.3.6.1.4.1.818.1.1.10.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime	1.3.6.1.4.1.818.1.1.10.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus	1.3.6.1.4.1.818.1.1.10.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint	1.3.6.1.4.1.818.1.1.10.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint	1.3.6.1.4.1.818.1.1.10.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity	1.3.6.1.4.1.818.1.1.10.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent	1.3.6.1.4.1.818.1.1.10.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown	1.3.6.1.4.1.818.1.1.10.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay	1.3.6.1.4.1.818.1.1.10.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet	1.3.6.1.4.1.818.1.1.10.10
NUM upsEventGetNext	1.3.6.1.4.1.818.1.1.10.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious	1.3.6.1.4.1.818.1.1.10.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp	1.3.6.1.4.1.818.1.1.10.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp	1.3.6.1.4.1.818.1.1.10.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize	1.3.6.1.4.1.818.1.1.10.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable	1.3.6.1.4.1.818.1.1.10.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry	1.3.6.1.4.1.818.1.1.10.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex	1.3.6.1.4.1.818.1.1.10.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
I32 upsEventCode	1.3.6.1.4.1.818.1.1.10.10.6.1.2	Integer32	read-only	The event code in numerical format.
NUM upsEventStatus	1.3.6.1.4.1.818.1.1.10.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.
NUM upsEventTime	1.3.6.1.4.1.818.1.1.10.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead	1.3.6.1.4.1.818.1.1.10.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite	1.3.6.1.4.1.818.1.1.10.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress	1.3.6.1.4.1.818.1.1.10.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize	1.3.6.1.4.1.818.1.1.10.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable	1.3.6.1.4.1.818.1.1.10.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry	1.3.6.1.4.1.818.1.1.10.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex	1.3.6.1.4.1.818.1.1.10.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue	1.3.6.1.4.1.818.1.1.10.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus	1.3.6.1.4.1.818.1.1.10.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues
NUM upsMainsStatisticsMBfail	1.3.6.1.4.1.818.1.1.10.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail	1.3.6.1.4.1.818.1.1.10.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2	1.3.6.1.4.1.818.1.1.10.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5	1.3.6.1.4.1.818.1.1.10.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10	1.3.6.1.4.1.818.1.1.10.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200	1.3.6.1.4.1.818.1.1.10.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel	1.3.6.1.4.1.818.1.1.10.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTimegen	1.3.6.1.4.1.818.1.1.10.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPgenERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission	1.3.6.1.4.1.818.1.1.10.10.21	DisplayString	read-write	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode	1.3.6.1.4.1.818.1.1.10.10.22	Integer32	read-write	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock	1.3.6.1.4.1.818.1.1.10.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock	1.3.6.1.4.1.818.1.1.10.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps	1.3.6.1.4.1.818.1.1.10.11
NTF upsTrapAlarmBatteryBad	1.3.6.1.4.1.818.1.1.10.11.1			One or more batteries have been determined to require replacement.
NTF upsTrapAlarmOnBattery	1.3.6.1.4.1.818.1.1.10.11.2			The UPS is drawing power from the batteries.
NTF upsTrapAlarmLowBattery	1.3.6.1.4.1.818.1.1.10.11.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsTrapAlarmDepletedBattery	1.3.6.1.4.1.818.1.1.10.11.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsTrapAlarmTempBad	1.3.6.1.4.1.818.1.1.10.11.5			A temperature is out of tolerance.
NTF upsTrapAlarmInputBad	1.3.6.1.4.1.818.1.1.10.11.6			An input condition is out of tolerance.
NTF upsTrapAlarmOutputBad	1.3.6.1.4.1.818.1.1.10.11.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsTrapAlarmOutputOverload	1.3.6.1.4.1.818.1.1.10.11.8			The output load exceeds the UPS output capacity.
NTF upsTrapAlarmOnBypass	1.3.6.1.4.1.818.1.1.10.11.9			The Bypass is presently engaged on the UPS.
NTF upsTrapAlarmBypassBad	1.3.6.1.4.1.818.1.1.10.11.10			The Bypass is out of tolerance.
NTF upsTrapAlarmOutputOffAsRequested	1.3.6.1.4.1.818.1.1.10.11.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsTrapAlarmUpsOffAsRequested	1.3.6.1.4.1.818.1.1.10.11.12			The entire UPS has shutdown as commanded.
NTF upsTrapAlarmChargerFailed	1.3.6.1.4.1.818.1.1.10.11.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsTrapAlarmUpsOutputOff	1.3.6.1.4.1.818.1.1.10.11.14			The output of the UPS is in the off state.
NTF upsTrapAlarmUpsSystemOff	1.3.6.1.4.1.818.1.1.10.11.15			The UPS system is in the off state.
NTF upsTrapAlarmFanFailure	1.3.6.1.4.1.818.1.1.10.11.16			The failure of one or more fans in the UPS has been detected.
NTF upsTrapAlarmFuseFailure	1.3.6.1.4.1.818.1.1.10.11.17			The failure of one or more fuses has been detected.
NTF upsTrapAlarmGeneralFault	1.3.6.1.4.1.818.1.1.10.11.18			A general fault in the UPS has been detected.
NTF upsTrapAlarmDiagnosticTestFailed	1.3.6.1.4.1.818.1.1.10.11.19			The result of the last diagnostic test indicates a failure.
NTF upsTrapAlarmCommunicationsLost	1.3.6.1.4.1.818.1.1.10.11.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsTrapAlarmAwaitingPower	1.3.6.1.4.1.818.1.1.10.11.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsTrapAlarmShutdownPending	1.3.6.1.4.1.818.1.1.10.11.22			A upsShutdownAfterDelay countdown is underway.
NTF upsTrapAlarmShutdownImminent	1.3.6.1.4.1.818.1.1.10.11.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsTrapAlarmTestInProgress	1.3.6.1.4.1.818.1.1.10.11.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsTrapAlarmReceptacleOff	1.3.6.1.4.1.818.1.1.10.11.25			A receptacle has been switched off.
NTF upsTrapAlarmHighspeedBusFailure	1.3.6.1.4.1.818.1.1.10.11.26			A problem on the Highspeed Bus communication is detected.
NTF upsTrapAlarmHighspeedBusJACRCFailure	1.3.6.1.4.1.818.1.1.10.11.27			A CRC failure on the Highspeed Bus JA is detected.
NTF upsTrapAlarmConnectivityBusFailure	1.3.6.1.4.1.818.1.1.10.11.28			A problem on the Connectivity Bus is detected.
NTF upsTrapAlarmHighspeedBusJBCRCFailure	1.3.6.1.4.1.818.1.1.10.11.29			A CRC failure on the Highspeed Bus JB is detected.
NTF upsTrapAlarmCurrentSharingFailure	1.3.6.1.4.1.818.1.1.10.11.30			An high current sharing on the parallel system is detected.
NTF upsTrapAlarmDCRippleFailure	1.3.6.1.4.1.818.1.1.10.11.31			An high ripple voltage on his DC link is detected.
NTF upsTrapAlarmBatteryBadRestored	1.3.6.1.4.1.818.1.1.10.11.33			A Battery bad condition is restored.
NTF upsTrapAlarmOnBatteryRestored	1.3.6.1.4.1.818.1.1.10.11.34			The UPS is drawing power from mains again.
NTF upsTrapAlarmLowBatteryRestored	1.3.6.1.4.1.818.1.1.10.11.35			A Low Battery condition is restored.
NTF upsTrapAlarmDepletedBatteryRestored	1.3.6.1.4.1.818.1.1.10.11.36			A Depleted Battery condition is restored.
NTF upsTrapAlarmTempBadRestored	1.3.6.1.4.1.818.1.1.10.11.37			A bad temperature condition is restored.
NTF upsTrapAlarmInputBadRestored	1.3.6.1.4.1.818.1.1.10.11.38			An input bad condition is restored.
NTF upsTrapAlarmOutputBadRestored	1.3.6.1.4.1.818.1.1.10.11.39			An output bad condition is restored.
NTF upsTrapAlarmOutputOverloadRestored	1.3.6.1.4.1.818.1.1.10.11.40			An output overload condition is restored.
NTF upsTrapAlarmOnBypassRestored	1.3.6.1.4.1.818.1.1.10.11.41			An On Bypass condition is restored.
NTF upsTrapAlarmBypassBadRestored	1.3.6.1.4.1.818.1.1.10.11.42			A Bypass bad condition is restored.
NTF upsTrapAlarmOutputOffAsRequestedRestored	1.3.6.1.4.1.818.1.1.10.11.43			A request shutdown has been restored.
NTF upsTrapAlarmUpsOffAsRequestedRestored	1.3.6.1.4.1.818.1.1.10.11.44			A entire UPS command has been restored.
NTF upsTrapAlarmChargerFailedRestored	1.3.6.1.4.1.818.1.1.10.11.45			A Charger Failer condition is restored.
NTF upsTrapAlarmUpsOutputOn	1.3.6.1.4.1.818.1.1.10.11.46			The output of the UPS switched in the on state.
NTF upsTrapAlarmUpsSystemOn	1.3.6.1.4.1.818.1.1.10.11.47			The UPS system is switched in the on state.
NTF upsTrapAlarmFanFailureRestored	1.3.6.1.4.1.818.1.1.10.11.48			A Fan failure condition is restored.
NTF upsTrapAlarmFuseFailureRestored	1.3.6.1.4.1.818.1.1.10.11.49			A Fuse failure condition is restored.
NTF upsTrapAlarmGeneralFaultRestored	1.3.6.1.4.1.818.1.1.10.11.50			A general fault is restored.
NTF upsTrapAlarmDiagnosticTestFailedRestored	1.3.6.1.4.1.818.1.1.10.11.51			A last diagnostic test indicates a failure is restored.
NTF upsTrapAlarmCommunicationsLostRestored	1.3.6.1.4.1.818.1.1.10.11.52			A problem in the communication between the agent and the UPS is restored.
NTF upsTrapAlarmAwaitingPowerRestored	1.3.6.1.4.1.818.1.1.10.11.53			A awaiting power condition is restored (*).
NTF upsTrapAlarmShutdownPendingRestored	1.3.6.1.4.1.818.1.1.10.11.54			A upsShutdownAfterDelay countdown is restored.
NTF upsTrapAlarmShutdownImminentRestored	1.3.6.1.4.1.818.1.1.10.11.55			A shutdown imminent condition is restored.
NTF upsTrapAlarmTestInProgressRestored	1.3.6.1.4.1.818.1.1.10.11.56			The test is in progress is terminated.
NTF upsTrapAlarmReceptacleOn	1.3.6.1.4.1.818.1.1.10.11.57			A receptacle has been switched on.
NTF upsTrapAlarmHighspeedBusRestored	1.3.6.1.4.1.818.1.1.10.11.58			A problem on the Highspeed Bus communication is restored.
NTF upsTrapAlarmHighspeedBusJACRCRestored	1.3.6.1.4.1.818.1.1.10.11.59			A CRC failure on the Highspeed Bus JA is restored.
NTF upsTrapAlarmConnectivityBusRestored	1.3.6.1.4.1.818.1.1.10.11.60			A problem on the Connectivity Bus communication is restored.
NTF upsTrapAlarmHighspeedBusJBCRCRestored	1.3.6.1.4.1.818.1.1.10.11.61			A CRC failure on the Highspeed Bus JB is restored.
NTF upsTrapAlarmCurrentSharingRestored	1.3.6.1.4.1.818.1.1.10.11.62			An high current sharing on the parallel system is restored.
NTF upsTrapAlarmDCRippleRestored	1.3.6.1.4.1.818.1.1.10.11.63			An high ripple voltage on his DC link is restored.
NTF upsTrapAlarmValueLow	1.3.6.1.4.1.818.1.1.10.11.129			A measurement value reached a value below its low-level threshold.
NTF upsTrapAlarmValueHigh	1.3.6.1.4.1.818.1.1.10.11.130			A measurement value reached a value higher than its high-level threshold.
NTF upsTrapAlarmValueLowRestored	1.3.6.1.4.1.818.1.1.10.11.133			A ValueLow alarm condition is restored.
NTF upsTrapAlarmValueHighRestored	1.3.6.1.4.1.818.1.1.10.11.134			A ValueHigh alarm condition is restored.
upsDiagnostic	1.3.6.1.4.1.818.1.1.10.12
I32 upsDiagnosticBusJACommunicationStatus	1.3.6.1.4.1.818.1.1.10.12.1	Integer32	read-only	Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)
I32 upsDiagnosticBusJBCommunicationStatus	1.3.6.1.4.1.818.1.1.10.12.2	Integer32	read-only	Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)
I32 upsDiagnosticBatteryLifetime	1.3.6.1.4.1.818.1.1.10.12.3	Integer32	read-only	The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)
I32 upsDiagnosticFansLifetime	1.3.6.1.4.1.818.1.1.10.12.4	Integer32	read-only	The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)
I32 upsDiagnosticDCcapacitorsLifetime	1.3.6.1.4.1.818.1.1.10.12.5	Integer32	read-only	The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)
I32 upsDiagnosticACcapacitorsLifetime	1.3.6.1.4.1.818.1.1.10.12.6	Integer32	read-only	The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)
I32 upsDiagnosticGlobalServiceCheck	1.3.6.1.4.1.818.1.1.10.12.7	Integer32	read-only	The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)
geFirstUPS	1.3.6.1.4.1.818.1.1.11
upsIdentfirst	1.3.6.1.4.1.818.1.1.11.1
STR upsIdentManufacturerfirst	1.3.6.1.4.1.818.1.1.11.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModelfirst	1.3.6.1.4.1.818.1.1.11.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersionfirst	1.3.6.1.4.1.818.1.1.11.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersionfirst	1.3.6.1.4.1.818.1.1.11.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentNamefirst	1.3.6.1.4.1.818.1.1.11.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevicesfirst	1.3.6.1.4.1.818.1.1.11.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumberfirst	1.3.6.1.4.1.818.1.1.11.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersionfirst	1.3.6.1.4.1.818.1.1.11.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTimefirst	1.3.6.1.4.1.818.1.1.11.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBatteryfirst	1.3.6.1.4.1.818.1.1.11.2
INT upsBatteryStatusfirst	1.3.6.1.4.1.818.1.1.11.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
I32 upsSecondsOnBatteryfirst	1.3.6.1.4.1.818.1.1.11.2.2	Integer32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemainingfirst	1.3.6.1.4.1.818.1.1.11.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemainingfirst	1.3.6.1.4.1.818.1.1.11.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltagefirst	1.3.6.1.4.1.818.1.1.11.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrentfirst	1.3.6.1.4.1.818.1.1.11.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperaturefirst	1.3.6.1.4.1.818.1.1.11.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
I32 upsBatteryRipplefirst	1.3.6.1.4.1.818.1.1.11.2.8	Integer32	read-only	The present DC link RMS voltage ripple.(*)
upsInputfirst	1.3.6.1.4.1.818.1.1.11.3
C32 upsInputLineBadsfirst	1.3.6.1.4.1.818.1.1.11.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLinesfirst	1.3.6.1.4.1.818.1.1.11.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputFirstTable	1.3.6.1.4.1.818.1.1.11.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputFirstEntry	1.3.6.1.4.1.818.1.1.11.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndexfirst	1.3.6.1.4.1.818.1.1.11.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequencyfirst	1.3.6.1.4.1.818.1.1.11.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltagefirst	1.3.6.1.4.1.818.1.1.11.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrentfirst	1.3.6.1.4.1.818.1.1.11.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePowerfirst	1.3.6.1.4.1.818.1.1.11.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMinfirst	1.3.6.1.4.1.818.1.1.11.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMaxfirst	1.3.6.1.4.1.818.1.1.11.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutputfirst	1.3.6.1.4.1.818.1.1.11.4
INT upsOutputSourcefirst	1.3.6.1.4.1.818.1.1.11.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequencyfirst	1.3.6.1.4.1.818.1.1.11.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLinesfirst	1.3.6.1.4.1.818.1.1.11.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputFirstTable	1.3.6.1.4.1.818.1.1.11.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputFirstEntry	1.3.6.1.4.1.818.1.1.11.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndexfirst	1.3.6.1.4.1.818.1.1.11.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltagefirst	1.3.6.1.4.1.818.1.1.11.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrentfirst	1.3.6.1.4.1.818.1.1.11.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPowerfirst	1.3.6.1.4.1.818.1.1.11.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoadfirst	1.3.6.1.4.1.818.1.1.11.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
I32 upsOutputPowerFactorfirst	1.3.6.1.4.1.818.1.1.11.4.4.1.6	Integer32	read-only	The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)
I32 upsOutputPeakCurrentfirst	1.3.6.1.4.1.818.1.1.11.4.4.1.7	Integer32	read-only	The present output peak current.(*)
I32 upsOutputShareCurrentfirst	1.3.6.1.4.1.818.1.1.11.4.4.1.8	Integer32	read-only	In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)
upsBypassfirst	1.3.6.1.4.1.818.1.1.11.5
NUM upsBypassFrequencyfirst	1.3.6.1.4.1.818.1.1.11.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLinesfirst	1.3.6.1.4.1.818.1.1.11.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassFirstTable	1.3.6.1.4.1.818.1.1.11.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassFirstEntry	1.3.6.1.4.1.818.1.1.11.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndexfirst	1.3.6.1.4.1.818.1.1.11.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltagefirst	1.3.6.1.4.1.818.1.1.11.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrentfirst	1.3.6.1.4.1.818.1.1.11.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPowerfirst	1.3.6.1.4.1.818.1.1.11.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarmfirst	1.3.6.1.4.1.818.1.1.11.6
G32 upsAlarmsPresentfirst	1.3.6.1.4.1.818.1.1.11.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmFirstTable	1.3.6.1.4.1.818.1.1.11.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmFirstEntry	1.3.6.1.4.1.818.1.1.11.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmIdfirst	1.3.6.1.4.1.818.1.1.11.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescrfirst	1.3.6.1.4.1.818.1.1.11.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTimefirst	1.3.6.1.4.1.818.1.1.11.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarmsfirst	1.3.6.1.4.1.818.1.1.11.6.3
upsAlarmBatteryBadfirst	1.3.6.1.4.1.818.1.1.11.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBatteryfirst	1.3.6.1.4.1.818.1.1.11.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBatteryfirst	1.3.6.1.4.1.818.1.1.11.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBatteryfirst	1.3.6.1.4.1.818.1.1.11.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBadfirst	1.3.6.1.4.1.818.1.1.11.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBadfirst	1.3.6.1.4.1.818.1.1.11.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBadfirst	1.3.6.1.4.1.818.1.1.11.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverloadfirst	1.3.6.1.4.1.818.1.1.11.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypassfirst	1.3.6.1.4.1.818.1.1.11.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBadfirst	1.3.6.1.4.1.818.1.1.11.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequestedfirst	1.3.6.1.4.1.818.1.1.11.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequestedfirst	1.3.6.1.4.1.818.1.1.11.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailedfirst	1.3.6.1.4.1.818.1.1.11.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOfffirst	1.3.6.1.4.1.818.1.1.11.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOfffirst	1.3.6.1.4.1.818.1.1.11.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailurefirst	1.3.6.1.4.1.818.1.1.11.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailurefirst	1.3.6.1.4.1.818.1.1.11.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFaultfirst	1.3.6.1.4.1.818.1.1.11.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailedfirst	1.3.6.1.4.1.818.1.1.11.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLostfirst	1.3.6.1.4.1.818.1.1.11.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPowerfirst	1.3.6.1.4.1.818.1.1.11.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPendingfirst	1.3.6.1.4.1.818.1.1.11.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminentfirst	1.3.6.1.4.1.818.1.1.11.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgressfirst	1.3.6.1.4.1.818.1.1.11.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOfffirst	1.3.6.1.4.1.818.1.1.11.6.3.25			The receptacle are switch off
upsAlarmHighSpeedBusFailurefirst	1.3.6.1.4.1.818.1.1.11.6.3.26			A problem on the High Speed Bus communication is detected
upsAlarmHighSpeedBusJACRCFailurefirst	1.3.6.1.4.1.818.1.1.11.6.3.27			A CRC failure on High Speed Bus JA is detected.
upsAlarmConnectivityBusFailurefirst	1.3.6.1.4.1.818.1.1.11.6.3.28			A problem on the Connectivity Bus communication is detected.
upsAlarmHighSpeedBusJBCRCFailurefirst	1.3.6.1.4.1.818.1.1.11.6.3.29			A CRC failure on High Speed Bus JB is detected.
upsAlarmCurrentSharingfirst	1.3.6.1.4.1.818.1.1.11.6.3.30			The UPS detects an high current sharing on the parallel system.
upsAlarmDCRipplefirst	1.3.6.1.4.1.818.1.1.11.6.3.31			The UPS detects an high ripple voltage on his DC link.
U32 upsAlarmMaskAfirst	1.3.6.1.4.1.818.1.1.11.6.4	Unsigned32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTestfirst	1.3.6.1.4.1.818.1.1.11.7
OID upsTestIdfirst	1.3.6.1.4.1.818.1.1.11.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLockfirst	1.3.6.1.4.1.818.1.1.11.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto tryagain } if (errorindex == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lockvalue + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummaryfirst	1.3.6.1.4.1.818.1.1.11.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetailfirst	1.3.6.1.4.1.818.1.1.11.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTimefirst	1.3.6.1.4.1.818.1.1.11.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTimefirst	1.3.6.1.4.1.818.1.1.11.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTestsfirst	1.3.6.1.4.1.818.1.1.11.7.7
upsTestNoTestsInitiatedfirst	1.3.6.1.4.1.818.1.1.11.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgressfirst	1.3.6.1.4.1.818.1.1.11.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTestfirst	1.3.6.1.4.1.818.1.1.11.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTestfirst	1.3.6.1.4.1.818.1.1.11.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibrationfirst	1.3.6.1.4.1.818.1.1.11.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControlfirst	1.3.6.1.4.1.818.1.1.11.8
INT upsShutdownTypefirst	1.3.6.1.4.1.818.1.1.11.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelayfirst	1.3.6.1.4.1.818.1.1.11.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelayfirst	1.3.6.1.4.1.818.1.1.11.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDurationfirst	1.3.6.1.4.1.818.1.1.11.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestartfirst	1.3.6.1.4.1.818.1.1.11.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNumfirst	1.3.6.1.4.1.818.1.1.11.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleFirstTable	1.3.6.1.4.1.818.1.1.11.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleFirstEntry	1.3.6.1.4.1.818.1.1.11.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndexfirst	1.3.6.1.4.1.818.1.1.11.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOfffirst	1.3.6.1.4.1.818.1.1.11.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSModefirst	1.3.6.1.4.1.818.1.1.11.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOfffirst	1.3.6.1.4.1.818.1.1.11.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethodfirst	1.3.6.1.4.1.818.1.1.11.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOfffirst	1.3.6.1.4.1.818.1.1.11.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOfffirst	1.3.6.1.4.1.818.1.1.11.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSourcefirst	1.3.6.1.4.1.818.1.1.11.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfigfirst	1.3.6.1.4.1.818.1.1.11.9
NUM upsConfigInputVoltagefirst	1.3.6.1.4.1.818.1.1.11.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreqfirst	1.3.6.1.4.1.818.1.1.11.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltagefirst	1.3.6.1.4.1.818.1.1.11.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreqfirst	1.3.6.1.4.1.818.1.1.11.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVAfirst	1.3.6.1.4.1.818.1.1.11.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPowerfirst	1.3.6.1.4.1.818.1.1.11.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTimefirst	1.3.6.1.4.1.818.1.1.11.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatusfirst	1.3.6.1.4.1.818.1.1.11.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPointfirst	1.3.6.1.4.1.818.1.1.11.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPointfirst	1.3.6.1.4.1.818.1.1.11.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacityfirst	1.3.6.1.4.1.818.1.1.11.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrentfirst	1.3.6.1.4.1.818.1.1.11.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdownfirst	1.3.6.1.4.1.818.1.1.11.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelayfirst	1.3.6.1.4.1.818.1.1.11.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSetfirst	1.3.6.1.4.1.818.1.1.11.10
NUM upsEventGetNextfirst	1.3.6.1.4.1.818.1.1.11.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPreviousfirst	1.3.6.1.4.1.818.1.1.11.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStampfirst	1.3.6.1.4.1.818.1.1.11.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStampfirst	1.3.6.1.4.1.818.1.1.11.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSizefirst	1.3.6.1.4.1.818.1.1.11.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventFirstTable	1.3.6.1.4.1.818.1.1.11.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventFirstEntry	1.3.6.1.4.1.818.1.1.11.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndexfirst	1.3.6.1.4.1.818.1.1.11.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
I32 upsEventCodefirst	1.3.6.1.4.1.818.1.1.11.10.6.1.2	Integer32	read-only	The event code in numerical format.
NUM upsEventStatusfirst	1.3.6.1.4.1.818.1.1.11.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.
NUM upsEventTimefirst	1.3.6.1.4.1.818.1.1.11.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersReadfirst	1.3.6.1.4.1.818.1.1.11.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWritefirst	1.3.6.1.4.1.818.1.1.11.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddressfirst	1.3.6.1.4.1.818.1.1.11.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSizefirst	1.3.6.1.4.1.818.1.1.11.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterFirstTable	1.3.6.1.4.1.818.1.1.11.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterFirstEntry	1.3.6.1.4.1.818.1.1.11.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndexfirst	1.3.6.1.4.1.818.1.1.11.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValuefirst	1.3.6.1.4.1.818.1.1.11.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatusfirst	1.3.6.1.4.1.818.1.1.11.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues
NUM upsMainsStatisticsMBfailfirst	1.3.6.1.4.1.818.1.1.11.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfailfirst	1.3.6.1.4.1.818.1.1.11.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2first	1.3.6.1.4.1.818.1.1.11.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5first	1.3.6.1.4.1.818.1.1.11.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10first	1.3.6.1.4.1.818.1.1.11.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200first	1.3.6.1.4.1.818.1.1.11.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRelfirst	1.3.6.1.4.1.818.1.1.11.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTimefirst	1.3.6.1.4.1.818.1.1.11.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPfirstERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermissionfirst	1.3.6.1.4.1.818.1.1.11.10.21	DisplayString	read-write	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCodefirst	1.3.6.1.4.1.818.1.1.11.10.22	Integer32	read-write	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLockfirst	1.3.6.1.4.1.818.1.1.11.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLockfirst	1.3.6.1.4.1.818.1.1.11.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTrapsfirst	1.3.6.1.4.1.818.1.1.11.11
NTF upsTrapAlarmBatteryBadfirst	1.3.6.1.4.1.818.1.1.11.11.1			One or more batteries have been determined to require replacement.
NTF upsTrapAlarmOnBatteryfirst	1.3.6.1.4.1.818.1.1.11.11.2			The UPS is drawing power from the batteries.
NTF upsTrapAlarmLowBatteryfirst	1.3.6.1.4.1.818.1.1.11.11.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsTrapAlarmDepletedBatteryfirst	1.3.6.1.4.1.818.1.1.11.11.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsTrapAlarmTempBadfirst	1.3.6.1.4.1.818.1.1.11.11.5			A temperature is out of tolerance.
NTF upsTrapAlarmInputBadfirst	1.3.6.1.4.1.818.1.1.11.11.6			An input condition is out of tolerance.
NTF upsTrapAlarmOutputBadfirst	1.3.6.1.4.1.818.1.1.11.11.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsTrapAlarmOutputOverloadfirst	1.3.6.1.4.1.818.1.1.11.11.8			The output load exceeds the UPS output capacity.
NTF upsTrapAlarmOnBypassfirst	1.3.6.1.4.1.818.1.1.11.11.9			The Bypass is presently engaged on the UPS.
NTF upsTrapAlarmBypassBadfirst	1.3.6.1.4.1.818.1.1.11.11.10			The Bypass is out of tolerance.
NTF upsTrapAlarmOutputOffAsRequestedfirst	1.3.6.1.4.1.818.1.1.11.11.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsTrapAlarmUpsOffAsRequestedfirst	1.3.6.1.4.1.818.1.1.11.11.12			The entire UPS has shutdown as commanded.
NTF upsTrapAlarmChargerFailedfirst	1.3.6.1.4.1.818.1.1.11.11.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsTrapAlarmUpsOutputOfffirst	1.3.6.1.4.1.818.1.1.11.11.14			The output of the UPS is in the off state.
NTF upsTrapAlarmUpsSystemOfffirst	1.3.6.1.4.1.818.1.1.11.11.15			The UPS system is in the off state.
NTF upsTrapAlarmFanFailurefirst	1.3.6.1.4.1.818.1.1.11.11.16			The failure of one or more fans in the UPS has been detected.
NTF upsTrapAlarmFuseFailurefirst	1.3.6.1.4.1.818.1.1.11.11.17			The failure of one or more fuses has been detected.
NTF upsTrapAlarmGeneralFaultfirst	1.3.6.1.4.1.818.1.1.11.11.18			A general fault in the UPS has been detected.
NTF upsTrapAlarmDiagnosticTestFailedfirst	1.3.6.1.4.1.818.1.1.11.11.19			The result of the last diagnostic test indicates a failure.
NTF upsTrapAlarmCommunicationsLostfirst	1.3.6.1.4.1.818.1.1.11.11.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsTrapAlarmAwaitingPowerfirst	1.3.6.1.4.1.818.1.1.11.11.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsTrapAlarmShutdownPendingfirst	1.3.6.1.4.1.818.1.1.11.11.22			A upsShutdownAfterDelay countdown is underway.
NTF upsTrapAlarmShutdownImminentfirst	1.3.6.1.4.1.818.1.1.11.11.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsTrapAlarmTestInProgressfirst	1.3.6.1.4.1.818.1.1.11.11.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsTrapAlarmReceptacleOfffirst	1.3.6.1.4.1.818.1.1.11.11.25			A receptacle has been switched off.
NTF upsTrapAlarmHighspeedBusFailurefirst	1.3.6.1.4.1.818.1.1.11.11.26			A problem on the Highspeed Bus communication is detected.
NTF upsTrapAlarmHighspeedBusJACRCFailurefirst	1.3.6.1.4.1.818.1.1.11.11.27			A CRC failure on the Highspeed Bus JB is detected.
NTF upsTrapAlarmConnectivityBusFailurefirst	1.3.6.1.4.1.818.1.1.11.11.28			A problem on the Connectivity Bus communication is detected
NTF upsTrapAlarmHighspeedBusJBCRCFailurefirst	1.3.6.1.4.1.818.1.1.11.11.29			A CRC failure on the Highspeed Bus JB is detected.
NTF upsTrapAlarmCurrentSharingFailurefirst	1.3.6.1.4.1.818.1.1.11.11.30			An high current sharing on the parallel system is detected.
NTF upsTrapAlarmDCRippleFailurefirst	1.3.6.1.4.1.818.1.1.11.11.31			An high ripple voltage on his DC link is detected.
NTF upsTrapAlarmBatteryBadRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.33			A Battery bad condition is restored.
NTF upsTrapAlarmOnBatteryRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.34			The UPS is drawing power from mains again.
NTF upsTrapAlarmLowBatteryRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.35			A Low Battery condition is restored.
NTF upsTrapAlarmDepletedBatteryRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.36			A Depleted Battery condition is restored.
NTF upsTrapAlarmTempBadRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.37			A bad temperature condition is restored.
NTF upsTrapAlarmInputBadRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.38			An input bad condition is restored.
NTF upsTrapAlarmOutputBadRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.39			An output bad condition is restored.
NTF upsTrapAlarmOutputOverloadRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.40			An output overload condition is restored.
NTF upsTrapAlarmOnBypassRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.41			An On Bypass condition is restored.
NTF upsTrapAlarmBypassBadRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.42			A Bypass bad condition is restored.
NTF upsTrapAlarmOutputOffAsRequestedRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.43			A request shutdown has been restored.
NTF upsTrapAlarmUpsOffAsRequestedRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.44			A entire UPS command has been restored.
NTF upsTrapAlarmChargerFailedRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.45			A Charger Failer condition is restored.
NTF upsTrapAlarmUpsOutputOnfirst	1.3.6.1.4.1.818.1.1.11.11.46			The output of the UPS switched in the on state.
NTF upsTrapAlarmUpsSystemOnfirst	1.3.6.1.4.1.818.1.1.11.11.47			The UPS system is switched in the on state.
NTF upsTrapAlarmFanFailureRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.48			A Fan failure condition is restored.
NTF upsTrapAlarmFuseFailureRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.49			A Fuse failure condition is restored.
NTF upsTrapAlarmGeneralFaultRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.50			A general fault is restored.
NTF upsTrapAlarmDiagnosticTestFailedRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.51			A last diagnostic test indicates a failure is restored.
NTF upsTrapAlarmCommunicationsLostRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.52			A problem in the communication between the agent and the UPS is restored.
NTF upsTrapAlarmAwaitingPowerRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.53			A awaiting power condition is restored (*).
NTF upsTrapAlarmShutdownPendingRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.54			A upsShutdownAfterDelay countdown is restored.
NTF upsTrapAlarmShutdownImminentRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.55			A shutdown imminent condition is restored.
NTF upsTrapAlarmTestInProgressRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.56			The test is in progress is terminated.
NTF upsTrapAlarmReceptacleOnfirst	1.3.6.1.4.1.818.1.1.11.11.57			A receptacle has been switched on.
NTF upsTrapAlarmHighspeedBusRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.58			A problem on the Highspeed Bus communication is restored.
NTF upsTrapAlarmHighspeedBusJACRCRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.59			A CRC failure on the Highspeed Bus JA is restored.
NTF upsTrapAlarmConnectivityBusRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.60			A problem on the Connectivity Bus communication is restored.
NTF upsTrapAlarmHighspeedBusJBCRCRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.61			A CRC failure on the Highspeed Bus JB is restored.
NTF upsTrapAlarmCurrentSharingRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.62			An high current sharing on the parallel system is restored.
NTF upsTrapAlarmDCRippleRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.63			An high ripple voltage on his DC link is restored.
NTF upsTrapAlarmValueLowfirst	1.3.6.1.4.1.818.1.1.11.11.129			A measurement value reached a value below its low-level threshold.
NTF upsTrapAlarmValueHighfirst	1.3.6.1.4.1.818.1.1.11.11.130			A measurement value reached a value higher than its high-level threshold.
NTF upsTrapAlarmValueLowRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.133			A ValueLow alarm condition is restored.
NTF upsTrapAlarmValueHighRestoredfirst	1.3.6.1.4.1.818.1.1.11.11.134			A ValueHigh alarm condition is restored.
upsDiagnosticfirst	1.3.6.1.4.1.818.1.1.11.12
I32 upsDiagnosticBusJACommunicationStatusfirst	1.3.6.1.4.1.818.1.1.11.12.1	Integer32	read-only	Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)
I32 upsDiagnosticBusJBCommunicationStatusfirst	1.3.6.1.4.1.818.1.1.11.12.2	Integer32	read-only	Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)
I32 upsDiagnosticBatteryLifetimefirst	1.3.6.1.4.1.818.1.1.11.12.3	Integer32	read-only	The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)
I32 upsDiagnosticFansLifetimefirst	1.3.6.1.4.1.818.1.1.11.12.4	Integer32	read-only	The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)
I32 upsDiagnosticDCcapacitorsLifetimefirst	1.3.6.1.4.1.818.1.1.11.12.5	Integer32	read-only	The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

imv

1.3.6.1.4.1.818

The MIB module to describe GE Digital Energy Uninterruptible Power Supplies.

geHardware

1.3.6.1.4.1.818.1

geUPS

1.3.6.1.4.1.818.1.1

I32 geDiscoveredUPSsMask

1.3.6.1.4.1.818.1.1.1

Integer32

read-only

Reading this variable returns bit mask indicating which UPSs in a parallel system are alive. Management software should poll only these UPSs on their snmp branches 11-18 as follows: 1 FirstUPS alive 2 SecondUPS alive 4 ThirdUPS alive 8 FourthUPS alive 16 FifthUPS alive 32 SixthUPS alive 64 SeventhUPS alive 128 EigthUPS alive Since the management software should always monitor the GenericUPS branch (10), this value has no meaning for single upses (which provide values on that snmp branch), and should be set to zero in that case.

STR geRequestPacket

1.3.6.1.4.1.818.1.1.2

DisplayString

read-write

Put the string, formatted as a IMV/CP4 packet, directly to internally RS485 bus. This OID could be used for accede directly to the internally RS485 bus from a remote place.

STR geReplyPacket

1.3.6.1.4.1.818.1.1.3

DisplayString

read-only

Contain the reply of the IMV/CP4 request packet sent using the OID geRequestPacket. Every time that a write command has be made at the OID ge RequestPacket, the value of this OID is erased.

geGenericUPS

1.3.6.1.4.1.818.1.1.10

upsIdent

1.3.6.1.4.1.818.1.1.10.1

STR upsIdentManufacturer

1.3.6.1.4.1.818.1.1.10.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModel

1.3.6.1.4.1.818.1.1.10.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersion

1.3.6.1.4.1.818.1.1.10.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersion

1.3.6.1.4.1.818.1.1.10.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentName

1.3.6.1.4.1.818.1.1.10.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDevices

1.3.6.1.4.1.818.1.1.10.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumber

1.3.6.1.4.1.818.1.1.10.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersion

1.3.6.1.4.1.818.1.1.10.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTime

1.3.6.1.4.1.818.1.1.10.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBattery

1.3.6.1.4.1.818.1.1.10.2

INT upsBatteryStatus

1.3.6.1.4.1.818.1.1.10.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

I32 upsSecondsOnBattery

1.3.6.1.4.1.818.1.1.10.2.2

Integer32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemaining

1.3.6.1.4.1.818.1.1.10.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemaining

1.3.6.1.4.1.818.1.1.10.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltage

1.3.6.1.4.1.818.1.1.10.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrent

1.3.6.1.4.1.818.1.1.10.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperature

1.3.6.1.4.1.818.1.1.10.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRipple

1.3.6.1.4.1.818.1.1.10.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInput

1.3.6.1.4.1.818.1.1.10.3

C32 upsInputLineBadsEx

1.3.6.1.4.1.818.1.1.10.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLines

1.3.6.1.4.1.818.1.1.10.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputTable

1.3.6.1.4.1.818.1.1.10.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputEntry

1.3.6.1.4.1.818.1.1.10.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndex

1.3.6.1.4.1.818.1.1.10.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequency

1.3.6.1.4.1.818.1.1.10.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltage

1.3.6.1.4.1.818.1.1.10.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrent

1.3.6.1.4.1.818.1.1.10.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePower

1.3.6.1.4.1.818.1.1.10.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMin

1.3.6.1.4.1.818.1.1.10.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMax

1.3.6.1.4.1.818.1.1.10.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutput

1.3.6.1.4.1.818.1.1.10.4

INT upsOutputSource

1.3.6.1.4.1.818.1.1.10.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequency

1.3.6.1.4.1.818.1.1.10.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLines

1.3.6.1.4.1.818.1.1.10.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputTable

1.3.6.1.4.1.818.1.1.10.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputEntry

1.3.6.1.4.1.818.1.1.10.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndex

1.3.6.1.4.1.818.1.1.10.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltage

1.3.6.1.4.1.818.1.1.10.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrent

1.3.6.1.4.1.818.1.1.10.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPower

1.3.6.1.4.1.818.1.1.10.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoad

1.3.6.1.4.1.818.1.1.10.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactor

1.3.6.1.4.1.818.1.1.10.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrent

1.3.6.1.4.1.818.1.1.10.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrent

1.3.6.1.4.1.818.1.1.10.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypass

1.3.6.1.4.1.818.1.1.10.5

NUM upsBypassFrequency

1.3.6.1.4.1.818.1.1.10.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLines

1.3.6.1.4.1.818.1.1.10.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassTable

1.3.6.1.4.1.818.1.1.10.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassEntry

1.3.6.1.4.1.818.1.1.10.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndex

1.3.6.1.4.1.818.1.1.10.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltage

1.3.6.1.4.1.818.1.1.10.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrent

1.3.6.1.4.1.818.1.1.10.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPower

1.3.6.1.4.1.818.1.1.10.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarm

1.3.6.1.4.1.818.1.1.10.6

G32 upsAlarmsPresent

1.3.6.1.4.1.818.1.1.10.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmTable

1.3.6.1.4.1.818.1.1.10.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmEntry

1.3.6.1.4.1.818.1.1.10.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmId

1.3.6.1.4.1.818.1.1.10.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescr

1.3.6.1.4.1.818.1.1.10.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTime

1.3.6.1.4.1.818.1.1.10.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarms

1.3.6.1.4.1.818.1.1.10.6.3

upsAlarmBatteryBad

1.3.6.1.4.1.818.1.1.10.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBattery

1.3.6.1.4.1.818.1.1.10.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBattery

1.3.6.1.4.1.818.1.1.10.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBattery

1.3.6.1.4.1.818.1.1.10.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBad

1.3.6.1.4.1.818.1.1.10.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBad

1.3.6.1.4.1.818.1.1.10.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBad

1.3.6.1.4.1.818.1.1.10.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverload

1.3.6.1.4.1.818.1.1.10.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypass

1.3.6.1.4.1.818.1.1.10.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBad

1.3.6.1.4.1.818.1.1.10.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequested

1.3.6.1.4.1.818.1.1.10.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequested

1.3.6.1.4.1.818.1.1.10.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailed

1.3.6.1.4.1.818.1.1.10.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOff

1.3.6.1.4.1.818.1.1.10.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOff

1.3.6.1.4.1.818.1.1.10.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailure

1.3.6.1.4.1.818.1.1.10.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailure

1.3.6.1.4.1.818.1.1.10.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFault

1.3.6.1.4.1.818.1.1.10.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailed

1.3.6.1.4.1.818.1.1.10.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLost

1.3.6.1.4.1.818.1.1.10.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPower

1.3.6.1.4.1.818.1.1.10.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPending

1.3.6.1.4.1.818.1.1.10.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminent

1.3.6.1.4.1.818.1.1.10.6.3.23

The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgress

1.3.6.1.4.1.818.1.1.10.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOff

1.3.6.1.4.1.818.1.1.10.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailure

1.3.6.1.4.1.818.1.1.10.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailure

1.3.6.1.4.1.818.1.1.10.6.3.27

A CRC problem on the Highspeed Bus JA is detected.

upsAlarmConnectivityBusFailure

1.3.6.1.4.1.818.1.1.10.6.3.28

A problem on the Connectivity Bus communication is detected

upsAlarmHighSpeedBusJBCRCFailure

1.3.6.1.4.1.818.1.1.10.6.3.29

A CRC problem on the Highspeed Bus JB is detected.

upsAlarmCurrentSharing

1.3.6.1.4.1.818.1.1.10.6.3.30

The System detects an high current sharing on the parallel system

upsAlarmDCRipple

1.3.6.1.4.1.818.1.1.10.6.3.31

The System detects an high ripple voltage on one DC link

U32 upsAlarmMaskA

1.3.6.1.4.1.818.1.1.10.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTest

1.3.6.1.4.1.818.1.1.10.7

OID upsTestId

1.3.6.1.4.1.818.1.1.10.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLock

1.3.6.1.4.1.818.1.1.10.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummary

1.3.6.1.4.1.818.1.1.10.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetail

1.3.6.1.4.1.818.1.1.10.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTime

1.3.6.1.4.1.818.1.1.10.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTime

1.3.6.1.4.1.818.1.1.10.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTests

1.3.6.1.4.1.818.1.1.10.7.7

upsTestNoTestsInitiated

1.3.6.1.4.1.818.1.1.10.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgress

1.3.6.1.4.1.818.1.1.10.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTest

1.3.6.1.4.1.818.1.1.10.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTest

1.3.6.1.4.1.818.1.1.10.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibration

1.3.6.1.4.1.818.1.1.10.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControl

1.3.6.1.4.1.818.1.1.10.8

INT upsShutdownType

1.3.6.1.4.1.818.1.1.10.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelay

1.3.6.1.4.1.818.1.1.10.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelay

1.3.6.1.4.1.818.1.1.10.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDuration

1.3.6.1.4.1.818.1.1.10.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestart

1.3.6.1.4.1.818.1.1.10.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNum

1.3.6.1.4.1.818.1.1.10.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleTable

1.3.6.1.4.1.818.1.1.10.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleEntry

1.3.6.1.4.1.818.1.1.10.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndex

1.3.6.1.4.1.818.1.1.10.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOff

1.3.6.1.4.1.818.1.1.10.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSMode

1.3.6.1.4.1.818.1.1.10.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOff

1.3.6.1.4.1.818.1.1.10.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethod

1.3.6.1.4.1.818.1.1.10.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOff

1.3.6.1.4.1.818.1.1.10.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOff

1.3.6.1.4.1.818.1.1.10.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSource

1.3.6.1.4.1.818.1.1.10.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfig

1.3.6.1.4.1.818.1.1.10.9

NUM upsConfigInputVoltage

1.3.6.1.4.1.818.1.1.10.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreq

1.3.6.1.4.1.818.1.1.10.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltage

1.3.6.1.4.1.818.1.1.10.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreq

1.3.6.1.4.1.818.1.1.10.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVA

1.3.6.1.4.1.818.1.1.10.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPower

1.3.6.1.4.1.818.1.1.10.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTime

1.3.6.1.4.1.818.1.1.10.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatus

1.3.6.1.4.1.818.1.1.10.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPoint

1.3.6.1.4.1.818.1.1.10.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPoint

1.3.6.1.4.1.818.1.1.10.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacity

1.3.6.1.4.1.818.1.1.10.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrent

1.3.6.1.4.1.818.1.1.10.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdown

1.3.6.1.4.1.818.1.1.10.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelay

1.3.6.1.4.1.818.1.1.10.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSet

1.3.6.1.4.1.818.1.1.10.10

NUM upsEventGetNext

1.3.6.1.4.1.818.1.1.10.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPrevious

1.3.6.1.4.1.818.1.1.10.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStamp

1.3.6.1.4.1.818.1.1.10.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStamp

1.3.6.1.4.1.818.1.1.10.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSize

1.3.6.1.4.1.818.1.1.10.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventTable

1.3.6.1.4.1.818.1.1.10.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventEntry

1.3.6.1.4.1.818.1.1.10.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndex

1.3.6.1.4.1.818.1.1.10.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCode

1.3.6.1.4.1.818.1.1.10.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatus

1.3.6.1.4.1.818.1.1.10.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTime

1.3.6.1.4.1.818.1.1.10.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersRead

1.3.6.1.4.1.818.1.1.10.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWrite

1.3.6.1.4.1.818.1.1.10.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.

NUM upsParametersStartAddress

1.3.6.1.4.1.818.1.1.10.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSize

1.3.6.1.4.1.818.1.1.10.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterTable

1.3.6.1.4.1.818.1.1.10.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterEntry

1.3.6.1.4.1.818.1.1.10.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndex

1.3.6.1.4.1.818.1.1.10.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValue

1.3.6.1.4.1.818.1.1.10.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatus

1.3.6.1.4.1.818.1.1.10.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfail

1.3.6.1.4.1.818.1.1.10.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfail

1.3.6.1.4.1.818.1.1.10.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2

1.3.6.1.4.1.818.1.1.10.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5

1.3.6.1.4.1.818.1.1.10.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10

1.3.6.1.4.1.818.1.1.10.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200

1.3.6.1.4.1.818.1.1.10.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypRel

1.3.6.1.4.1.818.1.1.10.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimegen

1.3.6.1.4.1.818.1.1.10.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPgenERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermission

1.3.6.1.4.1.818.1.1.10.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCode

1.3.6.1.4.1.818.1.1.10.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLock

1.3.6.1.4.1.818.1.1.10.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLock

1.3.6.1.4.1.818.1.1.10.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTraps

1.3.6.1.4.1.818.1.1.10.11

NTF upsTrapAlarmBatteryBad

1.3.6.1.4.1.818.1.1.10.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBattery

1.3.6.1.4.1.818.1.1.10.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBattery

1.3.6.1.4.1.818.1.1.10.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBattery

1.3.6.1.4.1.818.1.1.10.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBad

1.3.6.1.4.1.818.1.1.10.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBad

1.3.6.1.4.1.818.1.1.10.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBad

1.3.6.1.4.1.818.1.1.10.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverload

1.3.6.1.4.1.818.1.1.10.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypass

1.3.6.1.4.1.818.1.1.10.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBad

1.3.6.1.4.1.818.1.1.10.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequested

1.3.6.1.4.1.818.1.1.10.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequested

1.3.6.1.4.1.818.1.1.10.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailed

1.3.6.1.4.1.818.1.1.10.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOff

1.3.6.1.4.1.818.1.1.10.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOff

1.3.6.1.4.1.818.1.1.10.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailure

1.3.6.1.4.1.818.1.1.10.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailure

1.3.6.1.4.1.818.1.1.10.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFault

1.3.6.1.4.1.818.1.1.10.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailed

1.3.6.1.4.1.818.1.1.10.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLost

1.3.6.1.4.1.818.1.1.10.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPower

1.3.6.1.4.1.818.1.1.10.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPending

1.3.6.1.4.1.818.1.1.10.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminent

1.3.6.1.4.1.818.1.1.10.11.23

The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgress

1.3.6.1.4.1.818.1.1.10.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOff

1.3.6.1.4.1.818.1.1.10.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailure

1.3.6.1.4.1.818.1.1.10.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailure

1.3.6.1.4.1.818.1.1.10.11.27

A CRC failure on the Highspeed Bus JA is detected.

NTF upsTrapAlarmConnectivityBusFailure

1.3.6.1.4.1.818.1.1.10.11.28

A problem on the Connectivity Bus is detected.

NTF upsTrapAlarmHighspeedBusJBCRCFailure

1.3.6.1.4.1.818.1.1.10.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailure

1.3.6.1.4.1.818.1.1.10.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailure

1.3.6.1.4.1.818.1.1.10.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestored

1.3.6.1.4.1.818.1.1.10.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestored

1.3.6.1.4.1.818.1.1.10.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestored

1.3.6.1.4.1.818.1.1.10.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestored

1.3.6.1.4.1.818.1.1.10.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestored

1.3.6.1.4.1.818.1.1.10.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestored

1.3.6.1.4.1.818.1.1.10.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestored

1.3.6.1.4.1.818.1.1.10.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestored

1.3.6.1.4.1.818.1.1.10.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestored

1.3.6.1.4.1.818.1.1.10.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestored

1.3.6.1.4.1.818.1.1.10.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestored

1.3.6.1.4.1.818.1.1.10.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestored

1.3.6.1.4.1.818.1.1.10.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestored

1.3.6.1.4.1.818.1.1.10.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOn

1.3.6.1.4.1.818.1.1.10.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOn

1.3.6.1.4.1.818.1.1.10.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestored

1.3.6.1.4.1.818.1.1.10.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestored

1.3.6.1.4.1.818.1.1.10.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestored

1.3.6.1.4.1.818.1.1.10.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestored

1.3.6.1.4.1.818.1.1.10.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestored

1.3.6.1.4.1.818.1.1.10.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestored

1.3.6.1.4.1.818.1.1.10.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestored

1.3.6.1.4.1.818.1.1.10.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestored

1.3.6.1.4.1.818.1.1.10.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestored

1.3.6.1.4.1.818.1.1.10.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOn

1.3.6.1.4.1.818.1.1.10.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestored

1.3.6.1.4.1.818.1.1.10.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestored

1.3.6.1.4.1.818.1.1.10.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestored

1.3.6.1.4.1.818.1.1.10.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestored

1.3.6.1.4.1.818.1.1.10.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestored

1.3.6.1.4.1.818.1.1.10.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestored

1.3.6.1.4.1.818.1.1.10.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLow

1.3.6.1.4.1.818.1.1.10.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHigh

1.3.6.1.4.1.818.1.1.10.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestored

1.3.6.1.4.1.818.1.1.10.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestored

1.3.6.1.4.1.818.1.1.10.11.134

A ValueHigh alarm condition is restored.

upsDiagnostic

1.3.6.1.4.1.818.1.1.10.12

I32 upsDiagnosticBusJACommunicationStatus

1.3.6.1.4.1.818.1.1.10.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatus

1.3.6.1.4.1.818.1.1.10.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetime

1.3.6.1.4.1.818.1.1.10.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetime

1.3.6.1.4.1.818.1.1.10.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetime

1.3.6.1.4.1.818.1.1.10.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetime

1.3.6.1.4.1.818.1.1.10.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceCheck

1.3.6.1.4.1.818.1.1.10.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geFirstUPS

1.3.6.1.4.1.818.1.1.11

upsIdentfirst

1.3.6.1.4.1.818.1.1.11.1

STR upsIdentManufacturerfirst

1.3.6.1.4.1.818.1.1.11.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModelfirst

1.3.6.1.4.1.818.1.1.11.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersionfirst

1.3.6.1.4.1.818.1.1.11.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersionfirst

1.3.6.1.4.1.818.1.1.11.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentNamefirst

1.3.6.1.4.1.818.1.1.11.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDevicesfirst

1.3.6.1.4.1.818.1.1.11.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumberfirst

1.3.6.1.4.1.818.1.1.11.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersionfirst

1.3.6.1.4.1.818.1.1.11.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTimefirst

1.3.6.1.4.1.818.1.1.11.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBatteryfirst

1.3.6.1.4.1.818.1.1.11.2

INT upsBatteryStatusfirst

1.3.6.1.4.1.818.1.1.11.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

I32 upsSecondsOnBatteryfirst

1.3.6.1.4.1.818.1.1.11.2.2

Integer32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemainingfirst

1.3.6.1.4.1.818.1.1.11.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemainingfirst

1.3.6.1.4.1.818.1.1.11.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltagefirst

1.3.6.1.4.1.818.1.1.11.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrentfirst

1.3.6.1.4.1.818.1.1.11.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperaturefirst

1.3.6.1.4.1.818.1.1.11.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRipplefirst

1.3.6.1.4.1.818.1.1.11.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInputfirst

1.3.6.1.4.1.818.1.1.11.3

C32 upsInputLineBadsfirst

1.3.6.1.4.1.818.1.1.11.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLinesfirst

1.3.6.1.4.1.818.1.1.11.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputFirstTable

1.3.6.1.4.1.818.1.1.11.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputFirstEntry

1.3.6.1.4.1.818.1.1.11.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndexfirst

1.3.6.1.4.1.818.1.1.11.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequencyfirst

1.3.6.1.4.1.818.1.1.11.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltagefirst

1.3.6.1.4.1.818.1.1.11.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrentfirst

1.3.6.1.4.1.818.1.1.11.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePowerfirst

1.3.6.1.4.1.818.1.1.11.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMinfirst

1.3.6.1.4.1.818.1.1.11.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMaxfirst

1.3.6.1.4.1.818.1.1.11.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutputfirst

1.3.6.1.4.1.818.1.1.11.4

INT upsOutputSourcefirst

1.3.6.1.4.1.818.1.1.11.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequencyfirst

1.3.6.1.4.1.818.1.1.11.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLinesfirst

1.3.6.1.4.1.818.1.1.11.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputFirstTable

1.3.6.1.4.1.818.1.1.11.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputFirstEntry

1.3.6.1.4.1.818.1.1.11.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndexfirst

1.3.6.1.4.1.818.1.1.11.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltagefirst

1.3.6.1.4.1.818.1.1.11.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrentfirst

1.3.6.1.4.1.818.1.1.11.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPowerfirst

1.3.6.1.4.1.818.1.1.11.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoadfirst

1.3.6.1.4.1.818.1.1.11.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactorfirst

1.3.6.1.4.1.818.1.1.11.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrentfirst

1.3.6.1.4.1.818.1.1.11.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrentfirst

1.3.6.1.4.1.818.1.1.11.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypassfirst

1.3.6.1.4.1.818.1.1.11.5

NUM upsBypassFrequencyfirst

1.3.6.1.4.1.818.1.1.11.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLinesfirst

1.3.6.1.4.1.818.1.1.11.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassFirstTable

1.3.6.1.4.1.818.1.1.11.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassFirstEntry

1.3.6.1.4.1.818.1.1.11.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndexfirst

1.3.6.1.4.1.818.1.1.11.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltagefirst

1.3.6.1.4.1.818.1.1.11.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrentfirst

1.3.6.1.4.1.818.1.1.11.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPowerfirst

1.3.6.1.4.1.818.1.1.11.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarmfirst

1.3.6.1.4.1.818.1.1.11.6

G32 upsAlarmsPresentfirst

1.3.6.1.4.1.818.1.1.11.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmFirstTable

1.3.6.1.4.1.818.1.1.11.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmFirstEntry

1.3.6.1.4.1.818.1.1.11.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmIdfirst

1.3.6.1.4.1.818.1.1.11.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescrfirst

1.3.6.1.4.1.818.1.1.11.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTimefirst

1.3.6.1.4.1.818.1.1.11.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarmsfirst

1.3.6.1.4.1.818.1.1.11.6.3

upsAlarmBatteryBadfirst

1.3.6.1.4.1.818.1.1.11.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBatteryfirst

1.3.6.1.4.1.818.1.1.11.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBatteryfirst

1.3.6.1.4.1.818.1.1.11.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBatteryfirst

1.3.6.1.4.1.818.1.1.11.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBadfirst

1.3.6.1.4.1.818.1.1.11.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBadfirst

1.3.6.1.4.1.818.1.1.11.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBadfirst

1.3.6.1.4.1.818.1.1.11.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverloadfirst

1.3.6.1.4.1.818.1.1.11.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypassfirst

1.3.6.1.4.1.818.1.1.11.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBadfirst

1.3.6.1.4.1.818.1.1.11.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequestedfirst

1.3.6.1.4.1.818.1.1.11.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequestedfirst

1.3.6.1.4.1.818.1.1.11.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailedfirst

1.3.6.1.4.1.818.1.1.11.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOfffirst

1.3.6.1.4.1.818.1.1.11.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOfffirst

1.3.6.1.4.1.818.1.1.11.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailurefirst

1.3.6.1.4.1.818.1.1.11.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailurefirst

1.3.6.1.4.1.818.1.1.11.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFaultfirst

1.3.6.1.4.1.818.1.1.11.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailedfirst

1.3.6.1.4.1.818.1.1.11.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLostfirst

1.3.6.1.4.1.818.1.1.11.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPowerfirst

1.3.6.1.4.1.818.1.1.11.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPendingfirst

1.3.6.1.4.1.818.1.1.11.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminentfirst

1.3.6.1.4.1.818.1.1.11.6.3.23

The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgressfirst

1.3.6.1.4.1.818.1.1.11.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOfffirst

1.3.6.1.4.1.818.1.1.11.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailurefirst

1.3.6.1.4.1.818.1.1.11.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailurefirst

1.3.6.1.4.1.818.1.1.11.6.3.27

A CRC failure on High Speed Bus JA is detected.

upsAlarmConnectivityBusFailurefirst

1.3.6.1.4.1.818.1.1.11.6.3.28

A problem on the Connectivity Bus communication is detected.

upsAlarmHighSpeedBusJBCRCFailurefirst

1.3.6.1.4.1.818.1.1.11.6.3.29

A CRC failure on High Speed Bus JB is detected.

upsAlarmCurrentSharingfirst

1.3.6.1.4.1.818.1.1.11.6.3.30

The UPS detects an high current sharing on the parallel system.

upsAlarmDCRipplefirst

1.3.6.1.4.1.818.1.1.11.6.3.31

The UPS detects an high ripple voltage on his DC link.

U32 upsAlarmMaskAfirst

1.3.6.1.4.1.818.1.1.11.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTestfirst

1.3.6.1.4.1.818.1.1.11.7

OID upsTestIdfirst

1.3.6.1.4.1.818.1.1.11.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLockfirst

1.3.6.1.4.1.818.1.1.11.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummaryfirst

1.3.6.1.4.1.818.1.1.11.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetailfirst

1.3.6.1.4.1.818.1.1.11.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTimefirst

1.3.6.1.4.1.818.1.1.11.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTimefirst

1.3.6.1.4.1.818.1.1.11.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTestsfirst

1.3.6.1.4.1.818.1.1.11.7.7

upsTestNoTestsInitiatedfirst

1.3.6.1.4.1.818.1.1.11.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgressfirst

1.3.6.1.4.1.818.1.1.11.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTestfirst

1.3.6.1.4.1.818.1.1.11.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTestfirst

1.3.6.1.4.1.818.1.1.11.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibrationfirst

1.3.6.1.4.1.818.1.1.11.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControlfirst

1.3.6.1.4.1.818.1.1.11.8

INT upsShutdownTypefirst

1.3.6.1.4.1.818.1.1.11.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelayfirst

1.3.6.1.4.1.818.1.1.11.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelayfirst

1.3.6.1.4.1.818.1.1.11.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDurationfirst

1.3.6.1.4.1.818.1.1.11.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestartfirst

1.3.6.1.4.1.818.1.1.11.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNumfirst

1.3.6.1.4.1.818.1.1.11.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleFirstTable

1.3.6.1.4.1.818.1.1.11.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleFirstEntry

1.3.6.1.4.1.818.1.1.11.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndexfirst

1.3.6.1.4.1.818.1.1.11.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOfffirst

1.3.6.1.4.1.818.1.1.11.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSModefirst

1.3.6.1.4.1.818.1.1.11.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOfffirst

1.3.6.1.4.1.818.1.1.11.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethodfirst

1.3.6.1.4.1.818.1.1.11.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOfffirst

1.3.6.1.4.1.818.1.1.11.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOfffirst

1.3.6.1.4.1.818.1.1.11.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSourcefirst

1.3.6.1.4.1.818.1.1.11.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfigfirst

1.3.6.1.4.1.818.1.1.11.9

NUM upsConfigInputVoltagefirst

1.3.6.1.4.1.818.1.1.11.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreqfirst

1.3.6.1.4.1.818.1.1.11.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltagefirst

1.3.6.1.4.1.818.1.1.11.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreqfirst

1.3.6.1.4.1.818.1.1.11.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVAfirst

1.3.6.1.4.1.818.1.1.11.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPowerfirst

1.3.6.1.4.1.818.1.1.11.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTimefirst

1.3.6.1.4.1.818.1.1.11.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatusfirst

1.3.6.1.4.1.818.1.1.11.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPointfirst

1.3.6.1.4.1.818.1.1.11.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPointfirst

1.3.6.1.4.1.818.1.1.11.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacityfirst

1.3.6.1.4.1.818.1.1.11.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrentfirst

1.3.6.1.4.1.818.1.1.11.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdownfirst

1.3.6.1.4.1.818.1.1.11.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelayfirst

1.3.6.1.4.1.818.1.1.11.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSetfirst

1.3.6.1.4.1.818.1.1.11.10

NUM upsEventGetNextfirst

1.3.6.1.4.1.818.1.1.11.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPreviousfirst

1.3.6.1.4.1.818.1.1.11.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStampfirst

1.3.6.1.4.1.818.1.1.11.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStampfirst

1.3.6.1.4.1.818.1.1.11.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSizefirst

1.3.6.1.4.1.818.1.1.11.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventFirstTable

1.3.6.1.4.1.818.1.1.11.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventFirstEntry

1.3.6.1.4.1.818.1.1.11.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndexfirst

1.3.6.1.4.1.818.1.1.11.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCodefirst

1.3.6.1.4.1.818.1.1.11.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatusfirst

1.3.6.1.4.1.818.1.1.11.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTimefirst

1.3.6.1.4.1.818.1.1.11.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersReadfirst

1.3.6.1.4.1.818.1.1.11.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWritefirst

1.3.6.1.4.1.818.1.1.11.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.

NUM upsParametersStartAddressfirst

1.3.6.1.4.1.818.1.1.11.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSizefirst

1.3.6.1.4.1.818.1.1.11.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterFirstTable

1.3.6.1.4.1.818.1.1.11.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterFirstEntry

1.3.6.1.4.1.818.1.1.11.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndexfirst

1.3.6.1.4.1.818.1.1.11.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValuefirst

1.3.6.1.4.1.818.1.1.11.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatusfirst

1.3.6.1.4.1.818.1.1.11.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfailfirst

1.3.6.1.4.1.818.1.1.11.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfailfirst

1.3.6.1.4.1.818.1.1.11.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2first

1.3.6.1.4.1.818.1.1.11.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5first

1.3.6.1.4.1.818.1.1.11.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10first

1.3.6.1.4.1.818.1.1.11.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200first

1.3.6.1.4.1.818.1.1.11.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypRelfirst

1.3.6.1.4.1.818.1.1.11.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimefirst

1.3.6.1.4.1.818.1.1.11.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPfirstERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermissionfirst

1.3.6.1.4.1.818.1.1.11.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCodefirst

1.3.6.1.4.1.818.1.1.11.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLockfirst

1.3.6.1.4.1.818.1.1.11.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLockfirst

1.3.6.1.4.1.818.1.1.11.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTrapsfirst

1.3.6.1.4.1.818.1.1.11.11

NTF upsTrapAlarmBatteryBadfirst

1.3.6.1.4.1.818.1.1.11.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBatteryfirst

1.3.6.1.4.1.818.1.1.11.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBatteryfirst

1.3.6.1.4.1.818.1.1.11.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBatteryfirst

1.3.6.1.4.1.818.1.1.11.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBadfirst

1.3.6.1.4.1.818.1.1.11.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBadfirst

1.3.6.1.4.1.818.1.1.11.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBadfirst

1.3.6.1.4.1.818.1.1.11.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverloadfirst

1.3.6.1.4.1.818.1.1.11.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypassfirst

1.3.6.1.4.1.818.1.1.11.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBadfirst

1.3.6.1.4.1.818.1.1.11.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequestedfirst

1.3.6.1.4.1.818.1.1.11.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequestedfirst

1.3.6.1.4.1.818.1.1.11.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailedfirst

1.3.6.1.4.1.818.1.1.11.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOfffirst

1.3.6.1.4.1.818.1.1.11.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOfffirst

1.3.6.1.4.1.818.1.1.11.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailurefirst

1.3.6.1.4.1.818.1.1.11.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailurefirst

1.3.6.1.4.1.818.1.1.11.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFaultfirst

1.3.6.1.4.1.818.1.1.11.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailedfirst

1.3.6.1.4.1.818.1.1.11.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLostfirst

1.3.6.1.4.1.818.1.1.11.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPowerfirst

1.3.6.1.4.1.818.1.1.11.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPendingfirst

1.3.6.1.4.1.818.1.1.11.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminentfirst

1.3.6.1.4.1.818.1.1.11.11.23

The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgressfirst

1.3.6.1.4.1.818.1.1.11.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOfffirst

1.3.6.1.4.1.818.1.1.11.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailurefirst

1.3.6.1.4.1.818.1.1.11.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailurefirst

1.3.6.1.4.1.818.1.1.11.11.27

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmConnectivityBusFailurefirst

1.3.6.1.4.1.818.1.1.11.11.28

A problem on the Connectivity Bus communication is detected

NTF upsTrapAlarmHighspeedBusJBCRCFailurefirst

1.3.6.1.4.1.818.1.1.11.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailurefirst

1.3.6.1.4.1.818.1.1.11.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailurefirst

1.3.6.1.4.1.818.1.1.11.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOnfirst

1.3.6.1.4.1.818.1.1.11.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOnfirst

1.3.6.1.4.1.818.1.1.11.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOnfirst

1.3.6.1.4.1.818.1.1.11.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLowfirst

1.3.6.1.4.1.818.1.1.11.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHighfirst

1.3.6.1.4.1.818.1.1.11.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestoredfirst

1.3.6.1.4.1.818.1.1.11.11.134

A ValueHigh alarm condition is restored.

upsDiagnosticfirst

1.3.6.1.4.1.818.1.1.11.12

I32 upsDiagnosticBusJACommunicationStatusfirst

1.3.6.1.4.1.818.1.1.11.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatusfirst

1.3.6.1.4.1.818.1.1.11.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetimefirst

1.3.6.1.4.1.818.1.1.11.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetimefirst

1.3.6.1.4.1.818.1.1.11.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetimefirst

1.3.6.1.4.1.818.1.1.11.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetimefirst

1.3.6.1.4.1.818.1.1.11.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceCheckfirst

1.3.6.1.4.1.818.1.1.11.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geSecondUPS

1.3.6.1.4.1.818.1.1.12

upsIdentsecond

1.3.6.1.4.1.818.1.1.12.1

STR upsIdentManufacturersecond

1.3.6.1.4.1.818.1.1.12.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModelsecond

1.3.6.1.4.1.818.1.1.12.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersionsecond

1.3.6.1.4.1.818.1.1.12.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersionsecond

1.3.6.1.4.1.818.1.1.12.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentNamesecond

1.3.6.1.4.1.818.1.1.12.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDevicessecond

1.3.6.1.4.1.818.1.1.12.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumbersecond

1.3.6.1.4.1.818.1.1.12.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersionsecond

1.3.6.1.4.1.818.1.1.12.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTimesecond

1.3.6.1.4.1.818.1.1.12.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBatterysecond

1.3.6.1.4.1.818.1.1.12.2

INT upsBatteryStatussecond

1.3.6.1.4.1.818.1.1.12.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

I32 upsSecondsOnBatterysecond

1.3.6.1.4.1.818.1.1.12.2.2

Integer32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemainingsecond

1.3.6.1.4.1.818.1.1.12.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemainingsecond

1.3.6.1.4.1.818.1.1.12.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltagesecond

1.3.6.1.4.1.818.1.1.12.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrentsecond

1.3.6.1.4.1.818.1.1.12.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperaturesecond

1.3.6.1.4.1.818.1.1.12.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRipplesecond

1.3.6.1.4.1.818.1.1.12.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInputsecond

1.3.6.1.4.1.818.1.1.12.3

C32 upsInputLineBadssecond

1.3.6.1.4.1.818.1.1.12.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLinessecond

1.3.6.1.4.1.818.1.1.12.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputSecondTable

1.3.6.1.4.1.818.1.1.12.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputSecondEntry

1.3.6.1.4.1.818.1.1.12.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndexsecond

1.3.6.1.4.1.818.1.1.12.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequencysecond

1.3.6.1.4.1.818.1.1.12.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltagesecond

1.3.6.1.4.1.818.1.1.12.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrentsecond

1.3.6.1.4.1.818.1.1.12.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePowersecond

1.3.6.1.4.1.818.1.1.12.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMinsecond

1.3.6.1.4.1.818.1.1.12.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMaxsecond

1.3.6.1.4.1.818.1.1.12.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutputsecond

1.3.6.1.4.1.818.1.1.12.4

INT upsOutputSourcesecond

1.3.6.1.4.1.818.1.1.12.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequencysecond

1.3.6.1.4.1.818.1.1.12.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLinessecond

1.3.6.1.4.1.818.1.1.12.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputSecondTable

1.3.6.1.4.1.818.1.1.12.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputSecondEntry

1.3.6.1.4.1.818.1.1.12.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndexsecond

1.3.6.1.4.1.818.1.1.12.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltagesecond

1.3.6.1.4.1.818.1.1.12.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrentsecond

1.3.6.1.4.1.818.1.1.12.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPowersecond

1.3.6.1.4.1.818.1.1.12.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoadsecond

1.3.6.1.4.1.818.1.1.12.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactorsecond

1.3.6.1.4.1.818.1.1.12.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrentsecond

1.3.6.1.4.1.818.1.1.12.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrentsecond

1.3.6.1.4.1.818.1.1.12.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypasssecond

1.3.6.1.4.1.818.1.1.12.5

NUM upsBypassFrequencysecond

1.3.6.1.4.1.818.1.1.12.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLinessecond

1.3.6.1.4.1.818.1.1.12.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassSecondTable

1.3.6.1.4.1.818.1.1.12.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassSecondEntry

1.3.6.1.4.1.818.1.1.12.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndexsecond

1.3.6.1.4.1.818.1.1.12.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltagesecond

1.3.6.1.4.1.818.1.1.12.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrentsecond

1.3.6.1.4.1.818.1.1.12.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPowersecond

1.3.6.1.4.1.818.1.1.12.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarmsecond

1.3.6.1.4.1.818.1.1.12.6

G32 upsAlarmsPresentsecond

1.3.6.1.4.1.818.1.1.12.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmSecondTable

1.3.6.1.4.1.818.1.1.12.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmSecondEntry

1.3.6.1.4.1.818.1.1.12.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmIdsecond

1.3.6.1.4.1.818.1.1.12.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescrsecond

1.3.6.1.4.1.818.1.1.12.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTimesecond

1.3.6.1.4.1.818.1.1.12.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarmssecond

1.3.6.1.4.1.818.1.1.12.6.3

upsAlarmBatteryBadsecond

1.3.6.1.4.1.818.1.1.12.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBatterysecond

1.3.6.1.4.1.818.1.1.12.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBatterysecond

1.3.6.1.4.1.818.1.1.12.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBatterysecond

1.3.6.1.4.1.818.1.1.12.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBadsecond

1.3.6.1.4.1.818.1.1.12.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBadsecond

1.3.6.1.4.1.818.1.1.12.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBadsecond

1.3.6.1.4.1.818.1.1.12.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverloadsecond

1.3.6.1.4.1.818.1.1.12.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypasssecond

1.3.6.1.4.1.818.1.1.12.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBadsecond

1.3.6.1.4.1.818.1.1.12.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequestedsecond

1.3.6.1.4.1.818.1.1.12.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequestedsecond

1.3.6.1.4.1.818.1.1.12.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailedsecond

1.3.6.1.4.1.818.1.1.12.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOffsecond

1.3.6.1.4.1.818.1.1.12.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOffsecond

1.3.6.1.4.1.818.1.1.12.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailuresecond

1.3.6.1.4.1.818.1.1.12.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailuresecond

1.3.6.1.4.1.818.1.1.12.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFaultsecond

1.3.6.1.4.1.818.1.1.12.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailedsecond

1.3.6.1.4.1.818.1.1.12.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLostsecond

1.3.6.1.4.1.818.1.1.12.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPowersecond

1.3.6.1.4.1.818.1.1.12.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPendingsecond

1.3.6.1.4.1.818.1.1.12.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminentsecond

1.3.6.1.4.1.818.1.1.12.6.3.23

The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgresssecond

1.3.6.1.4.1.818.1.1.12.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOffsecond

1.3.6.1.4.1.818.1.1.12.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailuresecond

1.3.6.1.4.1.818.1.1.12.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailuresecond

1.3.6.1.4.1.818.1.1.12.6.3.27

A High Speed Bus CRC failure on Bus JB is detected.

upsAlarmConnectivityBusFailuresecond

1.3.6.1.4.1.818.1.1.12.6.3.28

A problem on the Connectivity Bus communication is detected.

upsAlarmHighSpeedBusJBCRCFailuresecond

1.3.6.1.4.1.818.1.1.12.6.3.29

A High Speed Bus CRC failure on Bus JB is detected.

upsAlarmCurrentSharingsecond

1.3.6.1.4.1.818.1.1.12.6.3.30

The UPS detects an high current sharing on the parallel system.

upsAlarmDCRipplesecond

1.3.6.1.4.1.818.1.1.12.6.3.31

The UPS detects an high ripple voltage on his DC link.

U32 upsAlarmMaskAsecond

1.3.6.1.4.1.818.1.1.12.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTestsecond

1.3.6.1.4.1.818.1.1.12.7

OID upsTestIdsecond

1.3.6.1.4.1.818.1.1.12.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLocksecond

1.3.6.1.4.1.818.1.1.12.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummarysecond

1.3.6.1.4.1.818.1.1.12.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetailsecond

1.3.6.1.4.1.818.1.1.12.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTimesecond

1.3.6.1.4.1.818.1.1.12.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTimesecond

1.3.6.1.4.1.818.1.1.12.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTestssecond

1.3.6.1.4.1.818.1.1.12.7.7

upsTestNoTestsInitiatedsecond

1.3.6.1.4.1.818.1.1.12.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgresssecond

1.3.6.1.4.1.818.1.1.12.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTestsecond

1.3.6.1.4.1.818.1.1.12.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTestsecond

1.3.6.1.4.1.818.1.1.12.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibrationsecond

1.3.6.1.4.1.818.1.1.12.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControlsecond

1.3.6.1.4.1.818.1.1.12.8

INT upsShutdownTypesecond

1.3.6.1.4.1.818.1.1.12.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelaysecond

1.3.6.1.4.1.818.1.1.12.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelaysecond

1.3.6.1.4.1.818.1.1.12.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDurationsecond

1.3.6.1.4.1.818.1.1.12.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestartsecond

1.3.6.1.4.1.818.1.1.12.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNumsecond

1.3.6.1.4.1.818.1.1.12.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleSecondTable

1.3.6.1.4.1.818.1.1.12.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleSecondEntry

1.3.6.1.4.1.818.1.1.12.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndexsecond

1.3.6.1.4.1.818.1.1.12.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOffsecond

1.3.6.1.4.1.818.1.1.12.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSModesecond

1.3.6.1.4.1.818.1.1.12.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOffsecond

1.3.6.1.4.1.818.1.1.12.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethodsecond

1.3.6.1.4.1.818.1.1.12.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOffsecond

1.3.6.1.4.1.818.1.1.12.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOffsecond

1.3.6.1.4.1.818.1.1.12.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSourcesecond

1.3.6.1.4.1.818.1.1.12.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfigsecond

1.3.6.1.4.1.818.1.1.12.9

NUM upsConfigInputVoltagesecond

1.3.6.1.4.1.818.1.1.12.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreqsecond

1.3.6.1.4.1.818.1.1.12.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltagesecond

1.3.6.1.4.1.818.1.1.12.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreqsecond

1.3.6.1.4.1.818.1.1.12.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVAsecond

1.3.6.1.4.1.818.1.1.12.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPowersecond

1.3.6.1.4.1.818.1.1.12.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTimesecond

1.3.6.1.4.1.818.1.1.12.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatussecond

1.3.6.1.4.1.818.1.1.12.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPointsecond

1.3.6.1.4.1.818.1.1.12.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPointsecond

1.3.6.1.4.1.818.1.1.12.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacitysecond

1.3.6.1.4.1.818.1.1.12.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrentsecond

1.3.6.1.4.1.818.1.1.12.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdownsecond

1.3.6.1.4.1.818.1.1.12.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelaysecond

1.3.6.1.4.1.818.1.1.12.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSetsecond

1.3.6.1.4.1.818.1.1.12.10

NUM upsEventGetNextsecond

1.3.6.1.4.1.818.1.1.12.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPrevioussecond

1.3.6.1.4.1.818.1.1.12.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStampsecond

1.3.6.1.4.1.818.1.1.12.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStampsecond

1.3.6.1.4.1.818.1.1.12.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSizesecond

1.3.6.1.4.1.818.1.1.12.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventSecondTable

1.3.6.1.4.1.818.1.1.12.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventSecondEntry

1.3.6.1.4.1.818.1.1.12.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndexsecond

1.3.6.1.4.1.818.1.1.12.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCodesecond

1.3.6.1.4.1.818.1.1.12.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatussecond

1.3.6.1.4.1.818.1.1.12.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTimesecond

1.3.6.1.4.1.818.1.1.12.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersReadsecond

1.3.6.1.4.1.818.1.1.12.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWritesecond

1.3.6.1.4.1.818.1.1.12.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the second value of the table with the lowest index number.

NUM upsParametersStartAddresssecond

1.3.6.1.4.1.818.1.1.12.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSizesecond

1.3.6.1.4.1.818.1.1.12.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterSecondTable

1.3.6.1.4.1.818.1.1.12.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterSecondEntry

1.3.6.1.4.1.818.1.1.12.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndexsecond

1.3.6.1.4.1.818.1.1.12.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValuesecond

1.3.6.1.4.1.818.1.1.12.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatussecond

1.3.6.1.4.1.818.1.1.12.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfailsecond

1.3.6.1.4.1.818.1.1.12.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfailsecond

1.3.6.1.4.1.818.1.1.12.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2second

1.3.6.1.4.1.818.1.1.12.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5second

1.3.6.1.4.1.818.1.1.12.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10second

1.3.6.1.4.1.818.1.1.12.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200second

1.3.6.1.4.1.818.1.1.12.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypRelsecond

1.3.6.1.4.1.818.1.1.12.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimesecond

1.3.6.1.4.1.818.1.1.12.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPsecondERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermissionsecond

1.3.6.1.4.1.818.1.1.12.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCodesecond

1.3.6.1.4.1.818.1.1.12.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLocksecond

1.3.6.1.4.1.818.1.1.12.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLocksecond

1.3.6.1.4.1.818.1.1.12.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTrapssecond

1.3.6.1.4.1.818.1.1.12.11

NTF upsTrapAlarmBatteryBadsecond

1.3.6.1.4.1.818.1.1.12.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBatterysecond

1.3.6.1.4.1.818.1.1.12.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBatterysecond

1.3.6.1.4.1.818.1.1.12.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBatterysecond

1.3.6.1.4.1.818.1.1.12.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBadsecond

1.3.6.1.4.1.818.1.1.12.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBadsecond

1.3.6.1.4.1.818.1.1.12.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBadsecond

1.3.6.1.4.1.818.1.1.12.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverloadsecond

1.3.6.1.4.1.818.1.1.12.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypasssecond

1.3.6.1.4.1.818.1.1.12.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBadsecond

1.3.6.1.4.1.818.1.1.12.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequestedsecond

1.3.6.1.4.1.818.1.1.12.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequestedsecond

1.3.6.1.4.1.818.1.1.12.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailedsecond

1.3.6.1.4.1.818.1.1.12.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOffsecond

1.3.6.1.4.1.818.1.1.12.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOffsecond

1.3.6.1.4.1.818.1.1.12.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailuresecond

1.3.6.1.4.1.818.1.1.12.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailuresecond

1.3.6.1.4.1.818.1.1.12.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFaultsecond

1.3.6.1.4.1.818.1.1.12.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailedsecond

1.3.6.1.4.1.818.1.1.12.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLostsecond

1.3.6.1.4.1.818.1.1.12.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPowersecond

1.3.6.1.4.1.818.1.1.12.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPendingsecond

1.3.6.1.4.1.818.1.1.12.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminentsecond

1.3.6.1.4.1.818.1.1.12.11.23

The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgresssecond

1.3.6.1.4.1.818.1.1.12.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOffsecond

1.3.6.1.4.1.818.1.1.12.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailuresecond

1.3.6.1.4.1.818.1.1.12.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailuresecond

1.3.6.1.4.1.818.1.1.12.11.27

A CRC failure on the Highspeed Bus JA is detected.

NTF upsTrapAlarmConnectivityBusFailuresecond

1.3.6.1.4.1.818.1.1.12.11.28

A problem on the Connectivity Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJBCRCFailuresecond

1.3.6.1.4.1.818.1.1.12.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailuresecond

1.3.6.1.4.1.818.1.1.12.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailuresecond

1.3.6.1.4.1.818.1.1.12.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOnsecond

1.3.6.1.4.1.818.1.1.12.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOnsecond

1.3.6.1.4.1.818.1.1.12.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOnsecond

1.3.6.1.4.1.818.1.1.12.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLowsecond

1.3.6.1.4.1.818.1.1.12.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHighsecond

1.3.6.1.4.1.818.1.1.12.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestoredsecond

1.3.6.1.4.1.818.1.1.12.11.134

A ValueHigh alarm condition is restored.

upsDiagnosticsecond

1.3.6.1.4.1.818.1.1.12.12

I32 upsDiagnosticBusJACommunicationStatussecond

1.3.6.1.4.1.818.1.1.12.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatussecond

1.3.6.1.4.1.818.1.1.12.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetimesecond

1.3.6.1.4.1.818.1.1.12.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetimesecond

1.3.6.1.4.1.818.1.1.12.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetimesecond

1.3.6.1.4.1.818.1.1.12.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetimesecond

1.3.6.1.4.1.818.1.1.12.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceChecksecond

1.3.6.1.4.1.818.1.1.12.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geThirdUPS

1.3.6.1.4.1.818.1.1.13

upsIdentthird

1.3.6.1.4.1.818.1.1.13.1

STR upsIdentManufacturerthird

1.3.6.1.4.1.818.1.1.13.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModelthird

1.3.6.1.4.1.818.1.1.13.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersionthird

1.3.6.1.4.1.818.1.1.13.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersionthird

1.3.6.1.4.1.818.1.1.13.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentNamethird

1.3.6.1.4.1.818.1.1.13.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDevicesthird

1.3.6.1.4.1.818.1.1.13.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumberthird

1.3.6.1.4.1.818.1.1.13.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersionthird

1.3.6.1.4.1.818.1.1.13.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTimethird

1.3.6.1.4.1.818.1.1.13.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBatterythird

1.3.6.1.4.1.818.1.1.13.2

INT upsBatteryStatusthird

1.3.6.1.4.1.818.1.1.13.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

I32 upsSecondsOnBatterythird

1.3.6.1.4.1.818.1.1.13.2.2

Integer32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemainingthird

1.3.6.1.4.1.818.1.1.13.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemainingthird

1.3.6.1.4.1.818.1.1.13.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltagethird

1.3.6.1.4.1.818.1.1.13.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrentthird

1.3.6.1.4.1.818.1.1.13.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperaturethird

1.3.6.1.4.1.818.1.1.13.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRipplethird

1.3.6.1.4.1.818.1.1.13.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInputthird

1.3.6.1.4.1.818.1.1.13.3

C32 upsInputLineBadsthird

1.3.6.1.4.1.818.1.1.13.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLinesthird

1.3.6.1.4.1.818.1.1.13.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputThirdTable

1.3.6.1.4.1.818.1.1.13.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputThirdEntry

1.3.6.1.4.1.818.1.1.13.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndexthird

1.3.6.1.4.1.818.1.1.13.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequencythird

1.3.6.1.4.1.818.1.1.13.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltagethird

1.3.6.1.4.1.818.1.1.13.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrentthird

1.3.6.1.4.1.818.1.1.13.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePowerthird

1.3.6.1.4.1.818.1.1.13.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMinthird

1.3.6.1.4.1.818.1.1.13.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMaxthird

1.3.6.1.4.1.818.1.1.13.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutputthird

1.3.6.1.4.1.818.1.1.13.4

INT upsOutputSourcethird

1.3.6.1.4.1.818.1.1.13.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequencythird

1.3.6.1.4.1.818.1.1.13.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLinesthird

1.3.6.1.4.1.818.1.1.13.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputThirdTable

1.3.6.1.4.1.818.1.1.13.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputThirdEntry

1.3.6.1.4.1.818.1.1.13.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndexthird

1.3.6.1.4.1.818.1.1.13.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltagethird

1.3.6.1.4.1.818.1.1.13.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrentthird

1.3.6.1.4.1.818.1.1.13.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPowerthird

1.3.6.1.4.1.818.1.1.13.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoadthird

1.3.6.1.4.1.818.1.1.13.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactorthird

1.3.6.1.4.1.818.1.1.13.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrentthird

1.3.6.1.4.1.818.1.1.13.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrentthird

1.3.6.1.4.1.818.1.1.13.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypassthird

1.3.6.1.4.1.818.1.1.13.5

NUM upsBypassFrequencythird

1.3.6.1.4.1.818.1.1.13.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLinesthird

1.3.6.1.4.1.818.1.1.13.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassThirdTable

1.3.6.1.4.1.818.1.1.13.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassThirdEntry

1.3.6.1.4.1.818.1.1.13.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndexthird

1.3.6.1.4.1.818.1.1.13.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltagethird

1.3.6.1.4.1.818.1.1.13.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrentthird

1.3.6.1.4.1.818.1.1.13.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPowerthird

1.3.6.1.4.1.818.1.1.13.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarmthird

1.3.6.1.4.1.818.1.1.13.6

G32 upsAlarmsPresentthird

1.3.6.1.4.1.818.1.1.13.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmThirdTable

1.3.6.1.4.1.818.1.1.13.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmThirdEntry

1.3.6.1.4.1.818.1.1.13.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmIdthird

1.3.6.1.4.1.818.1.1.13.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescrthird

1.3.6.1.4.1.818.1.1.13.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTimethird

1.3.6.1.4.1.818.1.1.13.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarmsthird

1.3.6.1.4.1.818.1.1.13.6.3

upsAlarmBatteryBadthird

1.3.6.1.4.1.818.1.1.13.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBatterythird

1.3.6.1.4.1.818.1.1.13.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBatterythird

1.3.6.1.4.1.818.1.1.13.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBatterythird

1.3.6.1.4.1.818.1.1.13.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBadthird

1.3.6.1.4.1.818.1.1.13.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBadthird

1.3.6.1.4.1.818.1.1.13.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBadthird

1.3.6.1.4.1.818.1.1.13.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverloadthird

1.3.6.1.4.1.818.1.1.13.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypassthird

1.3.6.1.4.1.818.1.1.13.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBadthird

1.3.6.1.4.1.818.1.1.13.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequestedthird

1.3.6.1.4.1.818.1.1.13.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequestedthird

1.3.6.1.4.1.818.1.1.13.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailedthird

1.3.6.1.4.1.818.1.1.13.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOffthird

1.3.6.1.4.1.818.1.1.13.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOffthird

1.3.6.1.4.1.818.1.1.13.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailurethird

1.3.6.1.4.1.818.1.1.13.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailurethird

1.3.6.1.4.1.818.1.1.13.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFaultthird

1.3.6.1.4.1.818.1.1.13.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailedthird

1.3.6.1.4.1.818.1.1.13.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLostthird

1.3.6.1.4.1.818.1.1.13.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPowerthird

1.3.6.1.4.1.818.1.1.13.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPendingthird

1.3.6.1.4.1.818.1.1.13.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminentthird

1.3.6.1.4.1.818.1.1.13.6.3.23

The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgressthird

1.3.6.1.4.1.818.1.1.13.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOffthird

1.3.6.1.4.1.818.1.1.13.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailurethird

1.3.6.1.4.1.818.1.1.13.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailurethird

1.3.6.1.4.1.818.1.1.13.6.3.27

A High Speed Bus CRC failure on Bus JA is detected.

upsAlarmConnectivityBusFailurethird

1.3.6.1.4.1.818.1.1.13.6.3.28

A problem on the Connectivity Bus communication is detected.

upsAlarmHighSpeedBusJBCRCFailurethird

1.3.6.1.4.1.818.1.1.13.6.3.29

A High Speed Bus CRC failure on Bus JB is detected.

upsAlarmCurrentSharingthird

1.3.6.1.4.1.818.1.1.13.6.3.30

The UPS detects an high current sharing on the parallel system.

upsAlarmDCRipplethird

1.3.6.1.4.1.818.1.1.13.6.3.31

The UPS detects an high ripple voltage on his DC link.

U32 upsAlarmMaskAthird

1.3.6.1.4.1.818.1.1.13.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTestthird

1.3.6.1.4.1.818.1.1.13.7

OID upsTestIdthird

1.3.6.1.4.1.818.1.1.13.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLockthird

1.3.6.1.4.1.818.1.1.13.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummarythird

1.3.6.1.4.1.818.1.1.13.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetailthird

1.3.6.1.4.1.818.1.1.13.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTimethird

1.3.6.1.4.1.818.1.1.13.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTimethird

1.3.6.1.4.1.818.1.1.13.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTeststhird

1.3.6.1.4.1.818.1.1.13.7.7

upsTestNoTestsInitiatedthird

1.3.6.1.4.1.818.1.1.13.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgressthird

1.3.6.1.4.1.818.1.1.13.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTestthird

1.3.6.1.4.1.818.1.1.13.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTestthird

1.3.6.1.4.1.818.1.1.13.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibrationthird

1.3.6.1.4.1.818.1.1.13.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControlthird

1.3.6.1.4.1.818.1.1.13.8

INT upsShutdownTypethird

1.3.6.1.4.1.818.1.1.13.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelaythird

1.3.6.1.4.1.818.1.1.13.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of Seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelaythird

1.3.6.1.4.1.818.1.1.13.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDurationthird

1.3.6.1.4.1.818.1.1.13.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestartthird

1.3.6.1.4.1.818.1.1.13.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNumthird

1.3.6.1.4.1.818.1.1.13.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleThirdTable

1.3.6.1.4.1.818.1.1.13.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleThirdEntry

1.3.6.1.4.1.818.1.1.13.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndexthird

1.3.6.1.4.1.818.1.1.13.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOffthird

1.3.6.1.4.1.818.1.1.13.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSModethird

1.3.6.1.4.1.818.1.1.13.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOffthird

1.3.6.1.4.1.818.1.1.13.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethodthird

1.3.6.1.4.1.818.1.1.13.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOffthird

1.3.6.1.4.1.818.1.1.13.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOffthird

1.3.6.1.4.1.818.1.1.13.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSourcethird

1.3.6.1.4.1.818.1.1.13.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfigthird

1.3.6.1.4.1.818.1.1.13.9

NUM upsConfigInputVoltagethird

1.3.6.1.4.1.818.1.1.13.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreqthird

1.3.6.1.4.1.818.1.1.13.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltagethird

1.3.6.1.4.1.818.1.1.13.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreqthird

1.3.6.1.4.1.818.1.1.13.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVAthird

1.3.6.1.4.1.818.1.1.13.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPowerthird

1.3.6.1.4.1.818.1.1.13.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTimethird

1.3.6.1.4.1.818.1.1.13.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatusthird

1.3.6.1.4.1.818.1.1.13.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPointthird

1.3.6.1.4.1.818.1.1.13.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPointthird

1.3.6.1.4.1.818.1.1.13.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacitythird

1.3.6.1.4.1.818.1.1.13.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrentthird

1.3.6.1.4.1.818.1.1.13.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdownthird

1.3.6.1.4.1.818.1.1.13.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelaythird

1.3.6.1.4.1.818.1.1.13.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSetthird

1.3.6.1.4.1.818.1.1.13.10

NUM upsEventGetNextthird

1.3.6.1.4.1.818.1.1.13.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPreviousthird

1.3.6.1.4.1.818.1.1.13.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStampthird

1.3.6.1.4.1.818.1.1.13.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStampthird

1.3.6.1.4.1.818.1.1.13.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSizethird

1.3.6.1.4.1.818.1.1.13.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventThirdTable

1.3.6.1.4.1.818.1.1.13.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventThirdEntry

1.3.6.1.4.1.818.1.1.13.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndexthird

1.3.6.1.4.1.818.1.1.13.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCodethird

1.3.6.1.4.1.818.1.1.13.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatusthird

1.3.6.1.4.1.818.1.1.13.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTimethird

1.3.6.1.4.1.818.1.1.13.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersReadthird

1.3.6.1.4.1.818.1.1.13.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWritethird

1.3.6.1.4.1.818.1.1.13.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the third value of the table with the lowest index number.

NUM upsParametersStartAddressthird

1.3.6.1.4.1.818.1.1.13.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSizethird

1.3.6.1.4.1.818.1.1.13.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterThirdTable

1.3.6.1.4.1.818.1.1.13.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterThirdEntry

1.3.6.1.4.1.818.1.1.13.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndexthird

1.3.6.1.4.1.818.1.1.13.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValuethird

1.3.6.1.4.1.818.1.1.13.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatusthird

1.3.6.1.4.1.818.1.1.13.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfailthird

1.3.6.1.4.1.818.1.1.13.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfailthird

1.3.6.1.4.1.818.1.1.13.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2third

1.3.6.1.4.1.818.1.1.13.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5third

1.3.6.1.4.1.818.1.1.13.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10third

1.3.6.1.4.1.818.1.1.13.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200third

1.3.6.1.4.1.818.1.1.13.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypRelthird

1.3.6.1.4.1.818.1.1.13.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimethird

1.3.6.1.4.1.818.1.1.13.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP second ERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermissionthird

1.3.6.1.4.1.818.1.1.13.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCodethird

1.3.6.1.4.1.818.1.1.13.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLockthird

1.3.6.1.4.1.818.1.1.13.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLockthird

1.3.6.1.4.1.818.1.1.13.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTrapsthird

1.3.6.1.4.1.818.1.1.13.11

NTF upsTrapAlarmBatteryBadthird

1.3.6.1.4.1.818.1.1.13.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBatterythird

1.3.6.1.4.1.818.1.1.13.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBatterythird

1.3.6.1.4.1.818.1.1.13.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBatterythird

1.3.6.1.4.1.818.1.1.13.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBadthird

1.3.6.1.4.1.818.1.1.13.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBadthird

1.3.6.1.4.1.818.1.1.13.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBadthird

1.3.6.1.4.1.818.1.1.13.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverloadthird

1.3.6.1.4.1.818.1.1.13.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypassthird

1.3.6.1.4.1.818.1.1.13.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBadthird

1.3.6.1.4.1.818.1.1.13.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequestedthird

1.3.6.1.4.1.818.1.1.13.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequestedthird

1.3.6.1.4.1.818.1.1.13.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailedthird

1.3.6.1.4.1.818.1.1.13.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOffthird

1.3.6.1.4.1.818.1.1.13.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOffthird

1.3.6.1.4.1.818.1.1.13.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailurethird

1.3.6.1.4.1.818.1.1.13.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailurethird

1.3.6.1.4.1.818.1.1.13.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFaultthird

1.3.6.1.4.1.818.1.1.13.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailedthird

1.3.6.1.4.1.818.1.1.13.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLostthird

1.3.6.1.4.1.818.1.1.13.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPowerthird

1.3.6.1.4.1.818.1.1.13.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPendingthird

1.3.6.1.4.1.818.1.1.13.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminentthird

1.3.6.1.4.1.818.1.1.13.11.23

The UPS will turn off power to the load in less than 5 secondss; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgressthird

1.3.6.1.4.1.818.1.1.13.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOffthird

1.3.6.1.4.1.818.1.1.13.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailurethird

1.3.6.1.4.1.818.1.1.13.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailurethird

1.3.6.1.4.1.818.1.1.13.11.27

A CRC failure on the Highspeed Bus JA is detected.

NTF upsTrapAlarmConnectivityBusFailurethird

1.3.6.1.4.1.818.1.1.13.11.28

A problem on the Connectivity Bus communication is detected

NTF upsTrapAlarmHighspeedBusJBCRCFailurethird

1.3.6.1.4.1.818.1.1.13.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailurethird

1.3.6.1.4.1.818.1.1.13.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailurethird

1.3.6.1.4.1.818.1.1.13.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestoredthird

1.3.6.1.4.1.818.1.1.13.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestoredthird

1.3.6.1.4.1.818.1.1.13.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestoredthird

1.3.6.1.4.1.818.1.1.13.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestoredthird

1.3.6.1.4.1.818.1.1.13.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestoredthird

1.3.6.1.4.1.818.1.1.13.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestoredthird

1.3.6.1.4.1.818.1.1.13.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestoredthird

1.3.6.1.4.1.818.1.1.13.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestoredthird

1.3.6.1.4.1.818.1.1.13.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestoredthird

1.3.6.1.4.1.818.1.1.13.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestoredthird

1.3.6.1.4.1.818.1.1.13.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestoredthird

1.3.6.1.4.1.818.1.1.13.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestoredthird

1.3.6.1.4.1.818.1.1.13.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestoredthird

1.3.6.1.4.1.818.1.1.13.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOnthird

1.3.6.1.4.1.818.1.1.13.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOnthird

1.3.6.1.4.1.818.1.1.13.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestoredthird

1.3.6.1.4.1.818.1.1.13.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestoredthird

1.3.6.1.4.1.818.1.1.13.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestoredthird

1.3.6.1.4.1.818.1.1.13.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestoredthird

1.3.6.1.4.1.818.1.1.13.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestoredthird

1.3.6.1.4.1.818.1.1.13.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestoredthird

1.3.6.1.4.1.818.1.1.13.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestoredthird

1.3.6.1.4.1.818.1.1.13.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestoredthird

1.3.6.1.4.1.818.1.1.13.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestoredthird

1.3.6.1.4.1.818.1.1.13.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOnthird

1.3.6.1.4.1.818.1.1.13.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestorethird

1.3.6.1.4.1.818.1.1.13.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestorethird

1.3.6.1.4.1.818.1.1.13.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestorethird

1.3.6.1.4.1.818.1.1.13.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestoredthird

1.3.6.1.4.1.818.1.1.13.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestoredthird

1.3.6.1.4.1.818.1.1.13.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestoredthird

1.3.6.1.4.1.818.1.1.13.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLowthird

1.3.6.1.4.1.818.1.1.13.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHighthird

1.3.6.1.4.1.818.1.1.13.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestoredthird

1.3.6.1.4.1.818.1.1.13.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestoredthird

1.3.6.1.4.1.818.1.1.13.11.134

A ValueHigh alarm condition is restored.

upsDiagnosticthird

1.3.6.1.4.1.818.1.1.13.12

I32 upsDiagnosticBusJACommunicationStatusthird

1.3.6.1.4.1.818.1.1.13.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatusthird

1.3.6.1.4.1.818.1.1.13.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetimethird

1.3.6.1.4.1.818.1.1.13.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetimethird

1.3.6.1.4.1.818.1.1.13.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetimethird

1.3.6.1.4.1.818.1.1.13.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetimethird

1.3.6.1.4.1.818.1.1.13.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceCheckthird

1.3.6.1.4.1.818.1.1.13.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geFourthUPS

1.3.6.1.4.1.818.1.1.14

upsIdentfourth

1.3.6.1.4.1.818.1.1.14.1

STR upsIdentManufacturerfourth

1.3.6.1.4.1.818.1.1.14.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModelfourth

1.3.6.1.4.1.818.1.1.14.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersionfourth

1.3.6.1.4.1.818.1.1.14.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersionfourth

1.3.6.1.4.1.818.1.1.14.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentNamefourth

1.3.6.1.4.1.818.1.1.14.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDevicesfourth

1.3.6.1.4.1.818.1.1.14.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumberfourth

1.3.6.1.4.1.818.1.1.14.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersionfourth

1.3.6.1.4.1.818.1.1.14.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTimefourth

1.3.6.1.4.1.818.1.1.14.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBatteryfourth

1.3.6.1.4.1.818.1.1.14.2

INT upsBatteryStatusfourth

1.3.6.1.4.1.818.1.1.14.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

I32 upsSecondsOnBatteryfourth

1.3.6.1.4.1.818.1.1.14.2.2

Integer32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemainingfourth

1.3.6.1.4.1.818.1.1.14.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemainingfourth

1.3.6.1.4.1.818.1.1.14.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltagefourth

1.3.6.1.4.1.818.1.1.14.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrentfourth

1.3.6.1.4.1.818.1.1.14.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperaturefourth

1.3.6.1.4.1.818.1.1.14.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRipplefourth

1.3.6.1.4.1.818.1.1.14.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInputfourth

1.3.6.1.4.1.818.1.1.14.3

C32 upsInputLineBadsfourth

1.3.6.1.4.1.818.1.1.14.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLinesfourth

1.3.6.1.4.1.818.1.1.14.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputFourthTable

1.3.6.1.4.1.818.1.1.14.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputFourthEntry

1.3.6.1.4.1.818.1.1.14.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndexfourth

1.3.6.1.4.1.818.1.1.14.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequencyfourth

1.3.6.1.4.1.818.1.1.14.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltagefourth

1.3.6.1.4.1.818.1.1.14.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrentfourth

1.3.6.1.4.1.818.1.1.14.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePowerfourth

1.3.6.1.4.1.818.1.1.14.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMinfourth

1.3.6.1.4.1.818.1.1.14.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMaxfourth

1.3.6.1.4.1.818.1.1.14.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutputfourth

1.3.6.1.4.1.818.1.1.14.4

INT upsOutputSourcefourth

1.3.6.1.4.1.818.1.1.14.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequencyfourth

1.3.6.1.4.1.818.1.1.14.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLinesfourth

1.3.6.1.4.1.818.1.1.14.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputFourthTable

1.3.6.1.4.1.818.1.1.14.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputFourthEntry

1.3.6.1.4.1.818.1.1.14.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndexfourth

1.3.6.1.4.1.818.1.1.14.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltagefourth

1.3.6.1.4.1.818.1.1.14.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrentfourth

1.3.6.1.4.1.818.1.1.14.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPowerfourth

1.3.6.1.4.1.818.1.1.14.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoadfourth

1.3.6.1.4.1.818.1.1.14.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactorfourth

1.3.6.1.4.1.818.1.1.14.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrentfourth

1.3.6.1.4.1.818.1.1.14.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrentfourth

1.3.6.1.4.1.818.1.1.14.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypassfourth

1.3.6.1.4.1.818.1.1.14.5

NUM upsBypassFrequencyfourth

1.3.6.1.4.1.818.1.1.14.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLinesfourth

1.3.6.1.4.1.818.1.1.14.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassFourthTable

1.3.6.1.4.1.818.1.1.14.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassFourthEntry

1.3.6.1.4.1.818.1.1.14.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndexfourth

1.3.6.1.4.1.818.1.1.14.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltagefourth

1.3.6.1.4.1.818.1.1.14.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrentfourth

1.3.6.1.4.1.818.1.1.14.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPowerfourth

1.3.6.1.4.1.818.1.1.14.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarmfourth

1.3.6.1.4.1.818.1.1.14.6

G32 upsAlarmsPresentfourth

1.3.6.1.4.1.818.1.1.14.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmFourthTable

1.3.6.1.4.1.818.1.1.14.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmFourthEntry

1.3.6.1.4.1.818.1.1.14.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmIdfourth

1.3.6.1.4.1.818.1.1.14.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescrfourth

1.3.6.1.4.1.818.1.1.14.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTimefourth

1.3.6.1.4.1.818.1.1.14.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarmsfourth

1.3.6.1.4.1.818.1.1.14.6.3

upsAlarmBatteryBadfourth

1.3.6.1.4.1.818.1.1.14.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBatteryfourth

1.3.6.1.4.1.818.1.1.14.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBatteryfourth

1.3.6.1.4.1.818.1.1.14.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBatteryfourth

1.3.6.1.4.1.818.1.1.14.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBadfourth

1.3.6.1.4.1.818.1.1.14.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBadfourth

1.3.6.1.4.1.818.1.1.14.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBadfourth

1.3.6.1.4.1.818.1.1.14.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverloadfourth

1.3.6.1.4.1.818.1.1.14.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypassfourth

1.3.6.1.4.1.818.1.1.14.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBadfourth

1.3.6.1.4.1.818.1.1.14.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequestedfourth

1.3.6.1.4.1.818.1.1.14.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequestedfourth

1.3.6.1.4.1.818.1.1.14.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailedfourth

1.3.6.1.4.1.818.1.1.14.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOfffourth

1.3.6.1.4.1.818.1.1.14.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOfffourth

1.3.6.1.4.1.818.1.1.14.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailurefourth

1.3.6.1.4.1.818.1.1.14.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailurefourth

1.3.6.1.4.1.818.1.1.14.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFaultfourth

1.3.6.1.4.1.818.1.1.14.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailedfourth

1.3.6.1.4.1.818.1.1.14.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLostfourth

1.3.6.1.4.1.818.1.1.14.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPowerfourth

1.3.6.1.4.1.818.1.1.14.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPendingfourth

1.3.6.1.4.1.818.1.1.14.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminentfourth

1.3.6.1.4.1.818.1.1.14.6.3.23

The UPS will turn off power to the load in less than 5 fourths; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgressfourth

1.3.6.1.4.1.818.1.1.14.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOfffourth

1.3.6.1.4.1.818.1.1.14.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailurefourth

1.3.6.1.4.1.818.1.1.14.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailurefourth

1.3.6.1.4.1.818.1.1.14.6.3.27

A High Speed Bus CRC failure on Bus JA is detected.

upsAlarmConnectivityBusFailurefourth

1.3.6.1.4.1.818.1.1.14.6.3.28

A problem on the Connectivity Bus communication is detected

upsAlarmHighSpeedBusJBCRCFailurefourth

1.3.6.1.4.1.818.1.1.14.6.3.29

A High Speed Bus CRC failure on Bus JB is detected.

upsAlarmCurrentSharingfourth

1.3.6.1.4.1.818.1.1.14.6.3.30

The UPS detects an high current sharing on the parallel system.

upsAlarmDCRipplefourth

1.3.6.1.4.1.818.1.1.14.6.3.31

The UPS detects an high ripple voltage on his DC link.

U32 upsAlarmMaskAfourth

1.3.6.1.4.1.818.1.1.14.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTestfourth

1.3.6.1.4.1.818.1.1.14.7

OID upsTestIdfourth

1.3.6.1.4.1.818.1.1.14.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLockfourth

1.3.6.1.4.1.818.1.1.14.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummaryfourth

1.3.6.1.4.1.818.1.1.14.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetailfourth

1.3.6.1.4.1.818.1.1.14.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTimefourth

1.3.6.1.4.1.818.1.1.14.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTimefourth

1.3.6.1.4.1.818.1.1.14.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTestsfourth

1.3.6.1.4.1.818.1.1.14.7.7

upsTestNoTestsInitiatedfourth

1.3.6.1.4.1.818.1.1.14.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgressfourth

1.3.6.1.4.1.818.1.1.14.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTestfourth

1.3.6.1.4.1.818.1.1.14.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTestfourth

1.3.6.1.4.1.818.1.1.14.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibrationfourth

1.3.6.1.4.1.818.1.1.14.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControlfourth

1.3.6.1.4.1.818.1.1.14.8

INT upsShutdownTypefourth

1.3.6.1.4.1.818.1.1.14.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelayfourth

1.3.6.1.4.1.818.1.1.14.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of fourths, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of fourths remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelayfourth

1.3.6.1.4.1.818.1.1.14.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of fourths, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of fourths until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDurationfourth

1.3.6.1.4.1.818.1.1.14.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of fourths, after which time the output will be started, including starting the UPS, if necessary. If the number of fourths required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 fourths. When read, upsRebootWithDuration shall return the number of fourths remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestartfourth

1.3.6.1.4.1.818.1.1.14.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNumfourth

1.3.6.1.4.1.818.1.1.14.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleFourthTable

1.3.6.1.4.1.818.1.1.14.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleFourthEntry

1.3.6.1.4.1.818.1.1.14.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndexfourth

1.3.6.1.4.1.818.1.1.14.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOfffourth

1.3.6.1.4.1.818.1.1.14.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSModefourth

1.3.6.1.4.1.818.1.1.14.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOfffourth

1.3.6.1.4.1.818.1.1.14.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethodfourth

1.3.6.1.4.1.818.1.1.14.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOfffourth

1.3.6.1.4.1.818.1.1.14.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOfffourth

1.3.6.1.4.1.818.1.1.14.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSourcefourth

1.3.6.1.4.1.818.1.1.14.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfigfourth

1.3.6.1.4.1.818.1.1.14.9

NUM upsConfigInputVoltagefourth

1.3.6.1.4.1.818.1.1.14.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreqfourth

1.3.6.1.4.1.818.1.1.14.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltagefourth

1.3.6.1.4.1.818.1.1.14.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreqfourth

1.3.6.1.4.1.818.1.1.14.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVAfourth

1.3.6.1.4.1.818.1.1.14.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPowerfourth

1.3.6.1.4.1.818.1.1.14.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTimefourth

1.3.6.1.4.1.818.1.1.14.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatusfourth

1.3.6.1.4.1.818.1.1.14.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPointfourth

1.3.6.1.4.1.818.1.1.14.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPointfourth

1.3.6.1.4.1.818.1.1.14.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacityfourth

1.3.6.1.4.1.818.1.1.14.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrentfourth

1.3.6.1.4.1.818.1.1.14.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdownfourth

1.3.6.1.4.1.818.1.1.14.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelayfourth

1.3.6.1.4.1.818.1.1.14.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSetfourth

1.3.6.1.4.1.818.1.1.14.10

NUM upsEventGetNextfourth

1.3.6.1.4.1.818.1.1.14.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPreviousfourth

1.3.6.1.4.1.818.1.1.14.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStampfourth

1.3.6.1.4.1.818.1.1.14.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStampfourth

1.3.6.1.4.1.818.1.1.14.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSizefourth

1.3.6.1.4.1.818.1.1.14.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventFourthTable

1.3.6.1.4.1.818.1.1.14.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventFourthEntry

1.3.6.1.4.1.818.1.1.14.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndexfourth

1.3.6.1.4.1.818.1.1.14.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCodefourth

1.3.6.1.4.1.818.1.1.14.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatusfourth

1.3.6.1.4.1.818.1.1.14.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTimefourth

1.3.6.1.4.1.818.1.1.14.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersReadfourth

1.3.6.1.4.1.818.1.1.14.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWritefourth

1.3.6.1.4.1.818.1.1.14.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the fourth value of the table with the lowest index number.

NUM upsParametersStartAddressfourth

1.3.6.1.4.1.818.1.1.14.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSizefourth

1.3.6.1.4.1.818.1.1.14.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterFourthTable

1.3.6.1.4.1.818.1.1.14.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterFourthEntry

1.3.6.1.4.1.818.1.1.14.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndexfourth

1.3.6.1.4.1.818.1.1.14.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValuefourth

1.3.6.1.4.1.818.1.1.14.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatusfourth

1.3.6.1.4.1.818.1.1.14.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfailfourth

1.3.6.1.4.1.818.1.1.14.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfailfourth

1.3.6.1.4.1.818.1.1.14.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2fourth

1.3.6.1.4.1.818.1.1.14.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5fourth

1.3.6.1.4.1.818.1.1.14.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10fourth

1.3.6.1.4.1.818.1.1.14.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200fourth

1.3.6.1.4.1.818.1.1.14.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypRelfourth

1.3.6.1.4.1.818.1.1.14.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimefourth

1.3.6.1.4.1.818.1.1.14.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPfourthERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermissionfourth

1.3.6.1.4.1.818.1.1.14.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCodefourth

1.3.6.1.4.1.818.1.1.14.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLockfourth

1.3.6.1.4.1.818.1.1.14.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLockfourth

1.3.6.1.4.1.818.1.1.14.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTrapsfourth

1.3.6.1.4.1.818.1.1.14.11

NTF upsTrapAlarmBatteryBadfourth

1.3.6.1.4.1.818.1.1.14.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBatteryfourth

1.3.6.1.4.1.818.1.1.14.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBatteryfourth

1.3.6.1.4.1.818.1.1.14.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBatteryfourth

1.3.6.1.4.1.818.1.1.14.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBadfourth

1.3.6.1.4.1.818.1.1.14.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBadfourth

1.3.6.1.4.1.818.1.1.14.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBadfourth

1.3.6.1.4.1.818.1.1.14.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverloadfourth

1.3.6.1.4.1.818.1.1.14.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypassfourth

1.3.6.1.4.1.818.1.1.14.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBadfourth

1.3.6.1.4.1.818.1.1.14.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequestedfourth

1.3.6.1.4.1.818.1.1.14.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequestedfourth

1.3.6.1.4.1.818.1.1.14.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailedfourth

1.3.6.1.4.1.818.1.1.14.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOfffourth

1.3.6.1.4.1.818.1.1.14.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOfffourth

1.3.6.1.4.1.818.1.1.14.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailurefourth

1.3.6.1.4.1.818.1.1.14.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailurefourth

1.3.6.1.4.1.818.1.1.14.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFaultfourth

1.3.6.1.4.1.818.1.1.14.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailedfourth

1.3.6.1.4.1.818.1.1.14.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLostfourth

1.3.6.1.4.1.818.1.1.14.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPowerfourth

1.3.6.1.4.1.818.1.1.14.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPendingfourth

1.3.6.1.4.1.818.1.1.14.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminentfourth

1.3.6.1.4.1.818.1.1.14.11.23

The UPS will turn off power to the load in less than 5 fourths; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgressfourth

1.3.6.1.4.1.818.1.1.14.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOfffourth

1.3.6.1.4.1.818.1.1.14.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailurefourth

1.3.6.1.4.1.818.1.1.14.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailurefourth

1.3.6.1.4.1.818.1.1.14.11.27

A CRC failure on the Highspeed Bus JA is detected.

NTF upsTrapAlarmConnectivityBusFailurefourth

1.3.6.1.4.1.818.1.1.14.11.28

A problem on the Connectivity Bus communication is detected

NTF upsTrapAlarmHighspeedBusJBCRCFailurefourth

1.3.6.1.4.1.818.1.1.14.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailurefourth

1.3.6.1.4.1.818.1.1.14.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailurefourth

1.3.6.1.4.1.818.1.1.14.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOnfourth

1.3.6.1.4.1.818.1.1.14.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOnfourth

1.3.6.1.4.1.818.1.1.14.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOnfourth

1.3.6.1.4.1.818.1.1.14.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestorefourth

1.3.6.1.4.1.818.1.1.14.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestorefourth

1.3.6.1.4.1.818.1.1.14.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestorefourth

1.3.6.1.4.1.818.1.1.14.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLowfourth

1.3.6.1.4.1.818.1.1.14.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHighfourth

1.3.6.1.4.1.818.1.1.14.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestoredfourth

1.3.6.1.4.1.818.1.1.14.11.134

A ValueHigh alarm condition is restored.

upsDiagnosticfourth

1.3.6.1.4.1.818.1.1.14.12

I32 upsDiagnosticBusJACommunicationStatusfourth

1.3.6.1.4.1.818.1.1.14.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatusfourth

1.3.6.1.4.1.818.1.1.14.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetimefourth

1.3.6.1.4.1.818.1.1.14.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetimefourth

1.3.6.1.4.1.818.1.1.14.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetimefourth

1.3.6.1.4.1.818.1.1.14.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetimefourth

1.3.6.1.4.1.818.1.1.14.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceCheckfourth

1.3.6.1.4.1.818.1.1.14.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geFifthUPS

1.3.6.1.4.1.818.1.1.15

upsIdentfifth

1.3.6.1.4.1.818.1.1.15.1

STR upsIdentManufacturerfifth

1.3.6.1.4.1.818.1.1.15.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModelfifth

1.3.6.1.4.1.818.1.1.15.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersionfifth

1.3.6.1.4.1.818.1.1.15.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersionfifth

1.3.6.1.4.1.818.1.1.15.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentNamefifth

1.3.6.1.4.1.818.1.1.15.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDevicesfifth

1.3.6.1.4.1.818.1.1.15.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumberfifth

1.3.6.1.4.1.818.1.1.15.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersionfifth

1.3.6.1.4.1.818.1.1.15.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTimefifth

1.3.6.1.4.1.818.1.1.15.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBatteryfifth

1.3.6.1.4.1.818.1.1.15.2

INT upsBatteryStatusfifth

1.3.6.1.4.1.818.1.1.15.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

I32 upsSecondsOnBatteryfifth

1.3.6.1.4.1.818.1.1.15.2.2

Integer32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemainingfifth

1.3.6.1.4.1.818.1.1.15.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemainingfifth

1.3.6.1.4.1.818.1.1.15.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltagefifth

1.3.6.1.4.1.818.1.1.15.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrentfifth

1.3.6.1.4.1.818.1.1.15.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperaturefifth

1.3.6.1.4.1.818.1.1.15.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRipplefifth

1.3.6.1.4.1.818.1.1.15.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInputfifth

1.3.6.1.4.1.818.1.1.15.3

C32 upsInputLineBadsfifth

1.3.6.1.4.1.818.1.1.15.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLinesfifth

1.3.6.1.4.1.818.1.1.15.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputFifthTable

1.3.6.1.4.1.818.1.1.15.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputFifthEntry

1.3.6.1.4.1.818.1.1.15.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndexfifth

1.3.6.1.4.1.818.1.1.15.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequencyfifth

1.3.6.1.4.1.818.1.1.15.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltagefifth

1.3.6.1.4.1.818.1.1.15.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrentfifth

1.3.6.1.4.1.818.1.1.15.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePowerfifth

1.3.6.1.4.1.818.1.1.15.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMinfifth

1.3.6.1.4.1.818.1.1.15.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMaxfifth

1.3.6.1.4.1.818.1.1.15.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutputfifth

1.3.6.1.4.1.818.1.1.15.4

INT upsOutputSourcefifth

1.3.6.1.4.1.818.1.1.15.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequencyfifth

1.3.6.1.4.1.818.1.1.15.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLinesfifth

1.3.6.1.4.1.818.1.1.15.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputFifthTable

1.3.6.1.4.1.818.1.1.15.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputFifthEntry

1.3.6.1.4.1.818.1.1.15.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndexfifth

1.3.6.1.4.1.818.1.1.15.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltagefifth

1.3.6.1.4.1.818.1.1.15.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrentfifth

1.3.6.1.4.1.818.1.1.15.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPowerfifth

1.3.6.1.4.1.818.1.1.15.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoadfifth

1.3.6.1.4.1.818.1.1.15.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactorfifth

1.3.6.1.4.1.818.1.1.15.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrentfifth

1.3.6.1.4.1.818.1.1.15.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrentfifth

1.3.6.1.4.1.818.1.1.15.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypassfifth

1.3.6.1.4.1.818.1.1.15.5

NUM upsBypassFrequencyfifth

1.3.6.1.4.1.818.1.1.15.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLinesfifth

1.3.6.1.4.1.818.1.1.15.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassFifthTable

1.3.6.1.4.1.818.1.1.15.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassFifthEntry

1.3.6.1.4.1.818.1.1.15.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndexfifth

1.3.6.1.4.1.818.1.1.15.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltagefifth

1.3.6.1.4.1.818.1.1.15.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrentfifth

1.3.6.1.4.1.818.1.1.15.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPowerfifth

1.3.6.1.4.1.818.1.1.15.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarmfifth

1.3.6.1.4.1.818.1.1.15.6

G32 upsAlarmsPresentfifth

1.3.6.1.4.1.818.1.1.15.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmFifthTable

1.3.6.1.4.1.818.1.1.15.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmFifthEntry

1.3.6.1.4.1.818.1.1.15.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmIdfifth

1.3.6.1.4.1.818.1.1.15.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescrfifth

1.3.6.1.4.1.818.1.1.15.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTimefifth

1.3.6.1.4.1.818.1.1.15.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarmsfifth

1.3.6.1.4.1.818.1.1.15.6.3

upsAlarmBatteryBadfifth

1.3.6.1.4.1.818.1.1.15.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBatteryfifth

1.3.6.1.4.1.818.1.1.15.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBatteryfifth

1.3.6.1.4.1.818.1.1.15.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBatteryfifth

1.3.6.1.4.1.818.1.1.15.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBadfifth

1.3.6.1.4.1.818.1.1.15.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBadfifth

1.3.6.1.4.1.818.1.1.15.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBadfifth

1.3.6.1.4.1.818.1.1.15.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverloadfifth

1.3.6.1.4.1.818.1.1.15.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypassfifth

1.3.6.1.4.1.818.1.1.15.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBadfifth

1.3.6.1.4.1.818.1.1.15.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequestedfifth

1.3.6.1.4.1.818.1.1.15.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequestedfifth

1.3.6.1.4.1.818.1.1.15.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailedfifth

1.3.6.1.4.1.818.1.1.15.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOfffifth

1.3.6.1.4.1.818.1.1.15.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOfffifth

1.3.6.1.4.1.818.1.1.15.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailurefifth

1.3.6.1.4.1.818.1.1.15.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailurefifth

1.3.6.1.4.1.818.1.1.15.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFaultfifth

1.3.6.1.4.1.818.1.1.15.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailedfifth

1.3.6.1.4.1.818.1.1.15.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLostfifth

1.3.6.1.4.1.818.1.1.15.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPowerfifth

1.3.6.1.4.1.818.1.1.15.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPendingfifth

1.3.6.1.4.1.818.1.1.15.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminentfifth

1.3.6.1.4.1.818.1.1.15.6.3.23

The UPS will turn off power to the load in less than 5 fifths; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgressfifth

1.3.6.1.4.1.818.1.1.15.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOfffifth

1.3.6.1.4.1.818.1.1.15.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailurefifth

1.3.6.1.4.1.818.1.1.15.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailurefifth

1.3.6.1.4.1.818.1.1.15.6.3.27

A High Speed Bus CRC failure on Bus JA is detected.

upsAlarmConnectivityBusFailurefifth

1.3.6.1.4.1.818.1.1.15.6.3.28

A problem on the Connectivity Bus communication is detected.

upsAlarmHighSpeedBusJBCRCFailurefifth

1.3.6.1.4.1.818.1.1.15.6.3.29

A High Speed Bus CRC failure on Bus JB is detected.

upsAlarmCurrentSharingfifth

1.3.6.1.4.1.818.1.1.15.6.3.30

The UPS detects an high current sharing on the parallel system.

upsAlarmDCRipplefifth

1.3.6.1.4.1.818.1.1.15.6.3.31

The UPS detects an high ripple voltage on his DC link.

U32 upsAlarmMaskAfifth

1.3.6.1.4.1.818.1.1.15.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTestfifth

1.3.6.1.4.1.818.1.1.15.7

OID upsTestIdfifth

1.3.6.1.4.1.818.1.1.15.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLockfifth

1.3.6.1.4.1.818.1.1.15.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummaryfifth

1.3.6.1.4.1.818.1.1.15.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetailfifth

1.3.6.1.4.1.818.1.1.15.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTimefifth

1.3.6.1.4.1.818.1.1.15.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTimefifth

1.3.6.1.4.1.818.1.1.15.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTestsfifth

1.3.6.1.4.1.818.1.1.15.7.7

upsTestNoTestsInitiatedfifth

1.3.6.1.4.1.818.1.1.15.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgressfifth

1.3.6.1.4.1.818.1.1.15.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTestfifth

1.3.6.1.4.1.818.1.1.15.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTestfifth

1.3.6.1.4.1.818.1.1.15.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibrationfifth

1.3.6.1.4.1.818.1.1.15.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControlfifth

1.3.6.1.4.1.818.1.1.15.8

INT upsShutdownTypefifth

1.3.6.1.4.1.818.1.1.15.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelayfifth

1.3.6.1.4.1.818.1.1.15.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of fifths, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of fifths remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelayfifth

1.3.6.1.4.1.818.1.1.15.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of fifths, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of fifths until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDurationfifth

1.3.6.1.4.1.818.1.1.15.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of fifths, after which time the output will be started, including starting the UPS, if necessary. If the number of fifths required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 fifths. When read, upsRebootWithDuration shall return the number of fifths remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestartfifth

1.3.6.1.4.1.818.1.1.15.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNumfifth

1.3.6.1.4.1.818.1.1.15.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleFifthTable

1.3.6.1.4.1.818.1.1.15.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleFifthEntry

1.3.6.1.4.1.818.1.1.15.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndexfifth

1.3.6.1.4.1.818.1.1.15.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOfffifth

1.3.6.1.4.1.818.1.1.15.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSModefifth

1.3.6.1.4.1.818.1.1.15.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOfffifth

1.3.6.1.4.1.818.1.1.15.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethodfifth

1.3.6.1.4.1.818.1.1.15.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOfffifth

1.3.6.1.4.1.818.1.1.15.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOfffifth

1.3.6.1.4.1.818.1.1.15.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSourcefifth

1.3.6.1.4.1.818.1.1.15.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfigfifth

1.3.6.1.4.1.818.1.1.15.9

NUM upsConfigInputVoltagefifth

1.3.6.1.4.1.818.1.1.15.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreqfifth

1.3.6.1.4.1.818.1.1.15.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltagefifth

1.3.6.1.4.1.818.1.1.15.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreqfifth

1.3.6.1.4.1.818.1.1.15.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVAfifth

1.3.6.1.4.1.818.1.1.15.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPowerfifth

1.3.6.1.4.1.818.1.1.15.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTimefifth

1.3.6.1.4.1.818.1.1.15.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatusfifth

1.3.6.1.4.1.818.1.1.15.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPointfifth

1.3.6.1.4.1.818.1.1.15.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPointfifth

1.3.6.1.4.1.818.1.1.15.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacityfifth

1.3.6.1.4.1.818.1.1.15.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrentfifth

1.3.6.1.4.1.818.1.1.15.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdownfifth

1.3.6.1.4.1.818.1.1.15.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelayfifth

1.3.6.1.4.1.818.1.1.15.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSetfifth

1.3.6.1.4.1.818.1.1.15.10

NUM upsEventGetNextfifth

1.3.6.1.4.1.818.1.1.15.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPreviousfifth

1.3.6.1.4.1.818.1.1.15.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStampfifth

1.3.6.1.4.1.818.1.1.15.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStampfifth

1.3.6.1.4.1.818.1.1.15.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSizefifth

1.3.6.1.4.1.818.1.1.15.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventFifthTable

1.3.6.1.4.1.818.1.1.15.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventFifthEntry

1.3.6.1.4.1.818.1.1.15.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndexfifth

1.3.6.1.4.1.818.1.1.15.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCodefifth

1.3.6.1.4.1.818.1.1.15.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatusfifth

1.3.6.1.4.1.818.1.1.15.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTimefifth

1.3.6.1.4.1.818.1.1.15.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersReadfifth

1.3.6.1.4.1.818.1.1.15.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWritefifth

1.3.6.1.4.1.818.1.1.15.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the fifth value of the table with the lowest index number.

NUM upsParametersStartAddressfifth

1.3.6.1.4.1.818.1.1.15.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSizefifth

1.3.6.1.4.1.818.1.1.15.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterFifthTable

1.3.6.1.4.1.818.1.1.15.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterFifthEntry

1.3.6.1.4.1.818.1.1.15.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndexfifth

1.3.6.1.4.1.818.1.1.15.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValuefifth

1.3.6.1.4.1.818.1.1.15.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatusfifth

1.3.6.1.4.1.818.1.1.15.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfailfifth

1.3.6.1.4.1.818.1.1.15.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfailfifth

1.3.6.1.4.1.818.1.1.15.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2fifth

1.3.6.1.4.1.818.1.1.15.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5fifth

1.3.6.1.4.1.818.1.1.15.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10fifth

1.3.6.1.4.1.818.1.1.15.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200fifth

1.3.6.1.4.1.818.1.1.15.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypRelfifth

1.3.6.1.4.1.818.1.1.15.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimefifth

1.3.6.1.4.1.818.1.1.15.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPfifthERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermissionfifth

1.3.6.1.4.1.818.1.1.15.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCodefifth

1.3.6.1.4.1.818.1.1.15.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLockfifth

1.3.6.1.4.1.818.1.1.15.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLockfifth

1.3.6.1.4.1.818.1.1.15.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTrapsfifth

1.3.6.1.4.1.818.1.1.15.11

NTF upsTrapAlarmBatteryBadfifth

1.3.6.1.4.1.818.1.1.15.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBatteryfifth

1.3.6.1.4.1.818.1.1.15.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBatteryfifth

1.3.6.1.4.1.818.1.1.15.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBatteryfifth

1.3.6.1.4.1.818.1.1.15.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBadfifth

1.3.6.1.4.1.818.1.1.15.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBadfifth

1.3.6.1.4.1.818.1.1.15.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBadfifth

1.3.6.1.4.1.818.1.1.15.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverloadfifth

1.3.6.1.4.1.818.1.1.15.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypassfifth

1.3.6.1.4.1.818.1.1.15.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBadfifth

1.3.6.1.4.1.818.1.1.15.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequestedfifth

1.3.6.1.4.1.818.1.1.15.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequestedfifth

1.3.6.1.4.1.818.1.1.15.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailedfifth

1.3.6.1.4.1.818.1.1.15.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOfffifth

1.3.6.1.4.1.818.1.1.15.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOfffifth

1.3.6.1.4.1.818.1.1.15.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailurefifth

1.3.6.1.4.1.818.1.1.15.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailurefifth

1.3.6.1.4.1.818.1.1.15.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFaultfifth

1.3.6.1.4.1.818.1.1.15.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailedfifth

1.3.6.1.4.1.818.1.1.15.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLostfifth

1.3.6.1.4.1.818.1.1.15.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPowerfifth

1.3.6.1.4.1.818.1.1.15.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPendingfifth

1.3.6.1.4.1.818.1.1.15.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminentfifth

1.3.6.1.4.1.818.1.1.15.11.23

The UPS will turn off power to the load in less than 5 fifths; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgressfifth

1.3.6.1.4.1.818.1.1.15.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOfffifth

1.3.6.1.4.1.818.1.1.15.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailurefifth

1.3.6.1.4.1.818.1.1.15.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailurefifth

1.3.6.1.4.1.818.1.1.15.11.27

A High Speed Bus CRC failure on Bus JA is detected.

NTF upsTrapAlarmConnectivityBusFailurefifth

1.3.6.1.4.1.818.1.1.15.11.28

A problem on the Connectivity Bus communication is detected

NTF upsTrapAlarmHighspeedBusJBCRCFailurefifth

1.3.6.1.4.1.818.1.1.15.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailurefifth

1.3.6.1.4.1.818.1.1.15.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailurefifth

1.3.6.1.4.1.818.1.1.15.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOnfifth

1.3.6.1.4.1.818.1.1.15.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOnfifth

1.3.6.1.4.1.818.1.1.15.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOnfifth

1.3.6.1.4.1.818.1.1.15.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestorefifth

1.3.6.1.4.1.818.1.1.15.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestorefifth

1.3.6.1.4.1.818.1.1.15.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestorefifth

1.3.6.1.4.1.818.1.1.15.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLowfifth

1.3.6.1.4.1.818.1.1.15.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHighfifth

1.3.6.1.4.1.818.1.1.15.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestoredfifth

1.3.6.1.4.1.818.1.1.15.11.134

A ValueHigh alarm condition is restored.

upsDiagnosticfifth

1.3.6.1.4.1.818.1.1.15.12

I32 upsDiagnosticBusJACommunicationStatusfifth

1.3.6.1.4.1.818.1.1.15.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatusfifth

1.3.6.1.4.1.818.1.1.15.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetimefifth

1.3.6.1.4.1.818.1.1.15.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetimefifth

1.3.6.1.4.1.818.1.1.15.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetimefifth

1.3.6.1.4.1.818.1.1.15.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetimefifth

1.3.6.1.4.1.818.1.1.15.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceCheckfifth

1.3.6.1.4.1.818.1.1.15.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geSixthUPS

1.3.6.1.4.1.818.1.1.16

upsIdentsixth

1.3.6.1.4.1.818.1.1.16.1

STR upsIdentManufacturersixth

1.3.6.1.4.1.818.1.1.16.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModelsixth

1.3.6.1.4.1.818.1.1.16.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersionsixth

1.3.6.1.4.1.818.1.1.16.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersionsixth

1.3.6.1.4.1.818.1.1.16.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentNamesixth

1.3.6.1.4.1.818.1.1.16.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDevicessixth

1.3.6.1.4.1.818.1.1.16.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumbersixth

1.3.6.1.4.1.818.1.1.16.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersionsixth

1.3.6.1.4.1.818.1.1.16.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTimesixth

1.3.6.1.4.1.818.1.1.16.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBatterysixth

1.3.6.1.4.1.818.1.1.16.2

INT upsBatteryStatussixth

1.3.6.1.4.1.818.1.1.16.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

NUM upsSecondsOnBatterysixth

1.3.6.1.4.1.818.1.1.16.2.2

NonNegativeInteger32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemainingsixth

1.3.6.1.4.1.818.1.1.16.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemainingsixth

1.3.6.1.4.1.818.1.1.16.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltagesixth

1.3.6.1.4.1.818.1.1.16.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrentsixth

1.3.6.1.4.1.818.1.1.16.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperaturesixth

1.3.6.1.4.1.818.1.1.16.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRipplesixth

1.3.6.1.4.1.818.1.1.16.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInputsixth

1.3.6.1.4.1.818.1.1.16.3

C32 upsInputLineBadssixth

1.3.6.1.4.1.818.1.1.16.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLinessixth

1.3.6.1.4.1.818.1.1.16.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputSixthTable

1.3.6.1.4.1.818.1.1.16.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputSixthEntry

1.3.6.1.4.1.818.1.1.16.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndexsixth

1.3.6.1.4.1.818.1.1.16.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequencysixth

1.3.6.1.4.1.818.1.1.16.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltagesixth

1.3.6.1.4.1.818.1.1.16.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrentsixth

1.3.6.1.4.1.818.1.1.16.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePowersixth

1.3.6.1.4.1.818.1.1.16.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMinsixth

1.3.6.1.4.1.818.1.1.16.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMaxsixth

1.3.6.1.4.1.818.1.1.16.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutputsixth

1.3.6.1.4.1.818.1.1.16.4

INT upsOutputSourcesixth

1.3.6.1.4.1.818.1.1.16.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequencysixth

1.3.6.1.4.1.818.1.1.16.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLinessixth

1.3.6.1.4.1.818.1.1.16.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputSixthTable

1.3.6.1.4.1.818.1.1.16.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputSixthEntry

1.3.6.1.4.1.818.1.1.16.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndexsixth

1.3.6.1.4.1.818.1.1.16.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltagesixth

1.3.6.1.4.1.818.1.1.16.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrentsixth

1.3.6.1.4.1.818.1.1.16.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPowersixth

1.3.6.1.4.1.818.1.1.16.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoadsixth

1.3.6.1.4.1.818.1.1.16.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactorsixth

1.3.6.1.4.1.818.1.1.16.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrentsixth

1.3.6.1.4.1.818.1.1.16.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrentsixth

1.3.6.1.4.1.818.1.1.16.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypasssixth

1.3.6.1.4.1.818.1.1.16.5

NUM upsBypassFrequencysixth

1.3.6.1.4.1.818.1.1.16.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLinessixth

1.3.6.1.4.1.818.1.1.16.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassSixthTable

1.3.6.1.4.1.818.1.1.16.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassSixthEntry

1.3.6.1.4.1.818.1.1.16.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndexsixth

1.3.6.1.4.1.818.1.1.16.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltagesixth

1.3.6.1.4.1.818.1.1.16.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrentsixth

1.3.6.1.4.1.818.1.1.16.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPowersixth

1.3.6.1.4.1.818.1.1.16.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarmsixth

1.3.6.1.4.1.818.1.1.16.6

G32 upsAlarmsPresentsixth

1.3.6.1.4.1.818.1.1.16.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmSixthTable

1.3.6.1.4.1.818.1.1.16.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmSixthEntry

1.3.6.1.4.1.818.1.1.16.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmIdsixth

1.3.6.1.4.1.818.1.1.16.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescrsixth

1.3.6.1.4.1.818.1.1.16.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTimesixth

1.3.6.1.4.1.818.1.1.16.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarmssixth

1.3.6.1.4.1.818.1.1.16.6.3

upsAlarmBatteryBadsixth

1.3.6.1.4.1.818.1.1.16.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBatterysixth

1.3.6.1.4.1.818.1.1.16.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBatterysixth

1.3.6.1.4.1.818.1.1.16.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBatterysixth

1.3.6.1.4.1.818.1.1.16.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBadsixth

1.3.6.1.4.1.818.1.1.16.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBadsixth

1.3.6.1.4.1.818.1.1.16.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBadsixth

1.3.6.1.4.1.818.1.1.16.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverloadsixth

1.3.6.1.4.1.818.1.1.16.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypasssixth

1.3.6.1.4.1.818.1.1.16.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBadsixth

1.3.6.1.4.1.818.1.1.16.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequestedsixth

1.3.6.1.4.1.818.1.1.16.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequestedsixth

1.3.6.1.4.1.818.1.1.16.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailedsixth

1.3.6.1.4.1.818.1.1.16.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOffsixth

1.3.6.1.4.1.818.1.1.16.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOffsixth

1.3.6.1.4.1.818.1.1.16.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailuresixth

1.3.6.1.4.1.818.1.1.16.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailuresixth

1.3.6.1.4.1.818.1.1.16.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFaultsixth

1.3.6.1.4.1.818.1.1.16.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailedsixth

1.3.6.1.4.1.818.1.1.16.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLostsixth

1.3.6.1.4.1.818.1.1.16.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPowersixth

1.3.6.1.4.1.818.1.1.16.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPendingsixth

1.3.6.1.4.1.818.1.1.16.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminentsixth

1.3.6.1.4.1.818.1.1.16.6.3.23

The UPS will turn off power to the load in less than 5 sixths; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgresssixth

1.3.6.1.4.1.818.1.1.16.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOffsixth

1.3.6.1.4.1.818.1.1.16.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailuresixth

1.3.6.1.4.1.818.1.1.16.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailuresixth

1.3.6.1.4.1.818.1.1.16.6.3.27

A High Speed Bus CRC failure on Bus JA is detected.

upsAlarmConnectivityBusFailuresixth

1.3.6.1.4.1.818.1.1.16.6.3.28

A problem on the Connectivity Bus communication is detected.

upsAlarmHighSpeedBusJBCRCFailuresixth

1.3.6.1.4.1.818.1.1.16.6.3.29

A High Speed Bus CRC failure on Bus JB is detected.

upsAlarmCurrentSharingsixth

1.3.6.1.4.1.818.1.1.16.6.3.30

The UPS detects an high current sharing on the parallel system.

upsAlarmDCRipplesixth

1.3.6.1.4.1.818.1.1.16.6.3.31

The UPS detects an high ripple voltage on his DC link.

U32 upsAlarmMaskAsixth

1.3.6.1.4.1.818.1.1.16.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTestsixth

1.3.6.1.4.1.818.1.1.16.7

OID upsTestIdsixth

1.3.6.1.4.1.818.1.1.16.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLocksixth

1.3.6.1.4.1.818.1.1.16.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummarysixth

1.3.6.1.4.1.818.1.1.16.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetailsixth

1.3.6.1.4.1.818.1.1.16.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTimesixth

1.3.6.1.4.1.818.1.1.16.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTimesixth

1.3.6.1.4.1.818.1.1.16.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTestssixth

1.3.6.1.4.1.818.1.1.16.7.7

upsTestNoTestsInitiatedsixth

1.3.6.1.4.1.818.1.1.16.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgresssixth

1.3.6.1.4.1.818.1.1.16.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTestsixth

1.3.6.1.4.1.818.1.1.16.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTestsixth

1.3.6.1.4.1.818.1.1.16.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibrationsixth

1.3.6.1.4.1.818.1.1.16.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControlsixth

1.3.6.1.4.1.818.1.1.16.8

INT upsShutdownTypesixth

1.3.6.1.4.1.818.1.1.16.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelaysixth

1.3.6.1.4.1.818.1.1.16.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of sixths, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of sixths remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelaysixth

1.3.6.1.4.1.818.1.1.16.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of sixths, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of sixths until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDurationsixth

1.3.6.1.4.1.818.1.1.16.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of sixths, after which time the output will be started, including starting the UPS, if necessary. If the number of sixths required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 sixths. When read, upsRebootWithDuration shall return the number of sixths remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestartsixth

1.3.6.1.4.1.818.1.1.16.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNumsixth

1.3.6.1.4.1.818.1.1.16.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleSixthTable

1.3.6.1.4.1.818.1.1.16.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleSixthEntry

1.3.6.1.4.1.818.1.1.16.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndexsixth

1.3.6.1.4.1.818.1.1.16.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOffsixth

1.3.6.1.4.1.818.1.1.16.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSModesixth

1.3.6.1.4.1.818.1.1.16.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOffsixth

1.3.6.1.4.1.818.1.1.16.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethodsixth

1.3.6.1.4.1.818.1.1.16.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOffsixth

1.3.6.1.4.1.818.1.1.16.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOffsixth

1.3.6.1.4.1.818.1.1.16.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSourcesixth

1.3.6.1.4.1.818.1.1.16.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfigsixth

1.3.6.1.4.1.818.1.1.16.9

NUM upsConfigInputVoltagesixth

1.3.6.1.4.1.818.1.1.16.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreqsixth

1.3.6.1.4.1.818.1.1.16.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltagesixth

1.3.6.1.4.1.818.1.1.16.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreqsixth

1.3.6.1.4.1.818.1.1.16.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVAsixth

1.3.6.1.4.1.818.1.1.16.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPowersixth

1.3.6.1.4.1.818.1.1.16.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTimesixth

1.3.6.1.4.1.818.1.1.16.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatussixth

1.3.6.1.4.1.818.1.1.16.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPointsixth

1.3.6.1.4.1.818.1.1.16.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPointsixth

1.3.6.1.4.1.818.1.1.16.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacitysixth

1.3.6.1.4.1.818.1.1.16.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrentsixth

1.3.6.1.4.1.818.1.1.16.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdownsixth

1.3.6.1.4.1.818.1.1.16.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelaysixth

1.3.6.1.4.1.818.1.1.16.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSetsixth

1.3.6.1.4.1.818.1.1.16.10

NUM upsEventGetNextsixth

1.3.6.1.4.1.818.1.1.16.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPrevioussixth

1.3.6.1.4.1.818.1.1.16.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStampsixth

1.3.6.1.4.1.818.1.1.16.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStampsixth

1.3.6.1.4.1.818.1.1.16.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSizesixth

1.3.6.1.4.1.818.1.1.16.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventSixthTable

1.3.6.1.4.1.818.1.1.16.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventSixthEntry

1.3.6.1.4.1.818.1.1.16.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndexsixth

1.3.6.1.4.1.818.1.1.16.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCodesixth

1.3.6.1.4.1.818.1.1.16.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatussixth

1.3.6.1.4.1.818.1.1.16.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTimesixth

1.3.6.1.4.1.818.1.1.16.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersReadsixth

1.3.6.1.4.1.818.1.1.16.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWritesixth

1.3.6.1.4.1.818.1.1.16.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the sixth value of the table with the lowest index number.

NUM upsParametersStartAddresssixth

1.3.6.1.4.1.818.1.1.16.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSizesixth

1.3.6.1.4.1.818.1.1.16.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterSixthTable

1.3.6.1.4.1.818.1.1.16.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterSixthEntry

1.3.6.1.4.1.818.1.1.16.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndexsixth

1.3.6.1.4.1.818.1.1.16.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValuesixth

1.3.6.1.4.1.818.1.1.16.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatussixth

1.3.6.1.4.1.818.1.1.16.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfailsixth

1.3.6.1.4.1.818.1.1.16.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfailsixth

1.3.6.1.4.1.818.1.1.16.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2sixth

1.3.6.1.4.1.818.1.1.16.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5sixth

1.3.6.1.4.1.818.1.1.16.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10sixth

1.3.6.1.4.1.818.1.1.16.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200sixth

1.3.6.1.4.1.818.1.1.16.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypRelsixth

1.3.6.1.4.1.818.1.1.16.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimesixth

1.3.6.1.4.1.818.1.1.16.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPsixthERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermissionsixth

1.3.6.1.4.1.818.1.1.16.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCodesixth

1.3.6.1.4.1.818.1.1.16.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLocksixth

1.3.6.1.4.1.818.1.1.16.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLocksixth

1.3.6.1.4.1.818.1.1.16.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTrapssixth

1.3.6.1.4.1.818.1.1.16.11

NTF upsTrapAlarmBatteryBadsixth

1.3.6.1.4.1.818.1.1.16.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBatterysixth

1.3.6.1.4.1.818.1.1.16.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBatterysixth

1.3.6.1.4.1.818.1.1.16.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBatterysixth

1.3.6.1.4.1.818.1.1.16.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBadsixth

1.3.6.1.4.1.818.1.1.16.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBadsixth

1.3.6.1.4.1.818.1.1.16.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBadsixth

1.3.6.1.4.1.818.1.1.16.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverloadsixth

1.3.6.1.4.1.818.1.1.16.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypasssixth

1.3.6.1.4.1.818.1.1.16.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBadsixth

1.3.6.1.4.1.818.1.1.16.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequestedsixth

1.3.6.1.4.1.818.1.1.16.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequestedsixth

1.3.6.1.4.1.818.1.1.16.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailedsixth

1.3.6.1.4.1.818.1.1.16.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOffsixth

1.3.6.1.4.1.818.1.1.16.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOffsixth

1.3.6.1.4.1.818.1.1.16.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailuresixth

1.3.6.1.4.1.818.1.1.16.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailuresixth

1.3.6.1.4.1.818.1.1.16.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFaultsixth

1.3.6.1.4.1.818.1.1.16.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailedsixth

1.3.6.1.4.1.818.1.1.16.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLostsixth

1.3.6.1.4.1.818.1.1.16.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPowersixth

1.3.6.1.4.1.818.1.1.16.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPendingsixth

1.3.6.1.4.1.818.1.1.16.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminentsixth

1.3.6.1.4.1.818.1.1.16.11.23

The UPS will turn off power to the load in less than 5 sixths; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgresssixth

1.3.6.1.4.1.818.1.1.16.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOffsixth

1.3.6.1.4.1.818.1.1.16.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailuresixth

1.3.6.1.4.1.818.1.1.16.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailuresixth

1.3.6.1.4.1.818.1.1.16.11.27

A CRC failure on the Highspeed Bus JA is detected.

NTF upsTrapAlarmConnectivityBusFailuresixth

1.3.6.1.4.1.818.1.1.16.11.28

A problem on the Connectivity Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJBCRCFailuresixth

1.3.6.1.4.1.818.1.1.16.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailuresixth

1.3.6.1.4.1.818.1.1.16.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailuresixth

1.3.6.1.4.1.818.1.1.16.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOnsixth

1.3.6.1.4.1.818.1.1.16.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOnsixth

1.3.6.1.4.1.818.1.1.16.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOnsixth

1.3.6.1.4.1.818.1.1.16.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestoresixth

1.3.6.1.4.1.818.1.1.16.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestoresixth

1.3.6.1.4.1.818.1.1.16.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestoresixth

1.3.6.1.4.1.818.1.1.16.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLowsixth

1.3.6.1.4.1.818.1.1.16.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHighsixth

1.3.6.1.4.1.818.1.1.16.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestoredsixth

1.3.6.1.4.1.818.1.1.16.11.134

A ValueHigh alarm condition is restored.

upsDiagnosticsixth

1.3.6.1.4.1.818.1.1.16.12

I32 upsDiagnosticBusJACommunicationStatussixth

1.3.6.1.4.1.818.1.1.16.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatussixth

1.3.6.1.4.1.818.1.1.16.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetimesixth

1.3.6.1.4.1.818.1.1.16.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetimesixth

1.3.6.1.4.1.818.1.1.16.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetimesixth

1.3.6.1.4.1.818.1.1.16.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetimesixth

1.3.6.1.4.1.818.1.1.16.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceChecksixth

1.3.6.1.4.1.818.1.1.16.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geSeventhUPS

1.3.6.1.4.1.818.1.1.17

upsIdentseventh

1.3.6.1.4.1.818.1.1.17.1

STR upsIdentManufacturerseventh

1.3.6.1.4.1.818.1.1.17.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModelseventh

1.3.6.1.4.1.818.1.1.17.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersionseventh

1.3.6.1.4.1.818.1.1.17.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersionseventh

1.3.6.1.4.1.818.1.1.17.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentNameseventh

1.3.6.1.4.1.818.1.1.17.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDevicesseventh

1.3.6.1.4.1.818.1.1.17.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumberseventh

1.3.6.1.4.1.818.1.1.17.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersionseventh

1.3.6.1.4.1.818.1.1.17.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTimeseventh

1.3.6.1.4.1.818.1.1.17.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBatteryseventh

1.3.6.1.4.1.818.1.1.17.2

INT upsBatteryStatusseventh

1.3.6.1.4.1.818.1.1.17.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

NUM upsSecondsOnBatteryseventh

1.3.6.1.4.1.818.1.1.17.2.2

NonNegativeInteger32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemainingseventh

1.3.6.1.4.1.818.1.1.17.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemainingseventh

1.3.6.1.4.1.818.1.1.17.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltageseventh

1.3.6.1.4.1.818.1.1.17.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrentseventh

1.3.6.1.4.1.818.1.1.17.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperatureseventh

1.3.6.1.4.1.818.1.1.17.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRippleseventh

1.3.6.1.4.1.818.1.1.17.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInputseventh

1.3.6.1.4.1.818.1.1.17.3

C32 upsInputLineBadsseventh

1.3.6.1.4.1.818.1.1.17.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLinesseventh

1.3.6.1.4.1.818.1.1.17.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputSeventhTable

1.3.6.1.4.1.818.1.1.17.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputSeventhEntry

1.3.6.1.4.1.818.1.1.17.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndexseventh

1.3.6.1.4.1.818.1.1.17.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequencyseventh

1.3.6.1.4.1.818.1.1.17.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltageseventh

1.3.6.1.4.1.818.1.1.17.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrentseventh

1.3.6.1.4.1.818.1.1.17.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePowerseventh

1.3.6.1.4.1.818.1.1.17.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMinseventh

1.3.6.1.4.1.818.1.1.17.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMaxseventh

1.3.6.1.4.1.818.1.1.17.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutputseventh

1.3.6.1.4.1.818.1.1.17.4

INT upsOutputSourceseventh

1.3.6.1.4.1.818.1.1.17.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequencyseventh

1.3.6.1.4.1.818.1.1.17.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLinesseventh

1.3.6.1.4.1.818.1.1.17.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputSeventhTable

1.3.6.1.4.1.818.1.1.17.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputSeventhEntry

1.3.6.1.4.1.818.1.1.17.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndexseventh

1.3.6.1.4.1.818.1.1.17.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltageseventh

1.3.6.1.4.1.818.1.1.17.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrentseventh

1.3.6.1.4.1.818.1.1.17.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPowerseventh

1.3.6.1.4.1.818.1.1.17.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoadseventh

1.3.6.1.4.1.818.1.1.17.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactorseventh

1.3.6.1.4.1.818.1.1.17.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrentseventh

1.3.6.1.4.1.818.1.1.17.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrentseventh

1.3.6.1.4.1.818.1.1.17.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypassseventh

1.3.6.1.4.1.818.1.1.17.5

NUM upsBypassFrequencyseventh

1.3.6.1.4.1.818.1.1.17.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLinesseventh

1.3.6.1.4.1.818.1.1.17.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassSeventhTable

1.3.6.1.4.1.818.1.1.17.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassSeventhEntry

1.3.6.1.4.1.818.1.1.17.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndexseventh

1.3.6.1.4.1.818.1.1.17.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltageseventh

1.3.6.1.4.1.818.1.1.17.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrentseventh

1.3.6.1.4.1.818.1.1.17.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPowerseventh

1.3.6.1.4.1.818.1.1.17.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarmseventh

1.3.6.1.4.1.818.1.1.17.6

G32 upsAlarmsPresentseventh

1.3.6.1.4.1.818.1.1.17.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmSeventhTable

1.3.6.1.4.1.818.1.1.17.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmSeventhEntry

1.3.6.1.4.1.818.1.1.17.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmIdseventh

1.3.6.1.4.1.818.1.1.17.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescrseventh

1.3.6.1.4.1.818.1.1.17.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTimeseventh

1.3.6.1.4.1.818.1.1.17.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarmsseventh

1.3.6.1.4.1.818.1.1.17.6.3

upsAlarmBatteryBadseventh

1.3.6.1.4.1.818.1.1.17.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBatteryseventh

1.3.6.1.4.1.818.1.1.17.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBatteryseventh

1.3.6.1.4.1.818.1.1.17.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBatteryseventh

1.3.6.1.4.1.818.1.1.17.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBadseventh

1.3.6.1.4.1.818.1.1.17.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBadseventh

1.3.6.1.4.1.818.1.1.17.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBadseventh

1.3.6.1.4.1.818.1.1.17.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverloadseventh

1.3.6.1.4.1.818.1.1.17.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypassseventh

1.3.6.1.4.1.818.1.1.17.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBadseventh

1.3.6.1.4.1.818.1.1.17.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequestedseventh

1.3.6.1.4.1.818.1.1.17.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequestedseventh

1.3.6.1.4.1.818.1.1.17.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailedseventh

1.3.6.1.4.1.818.1.1.17.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOffseventh

1.3.6.1.4.1.818.1.1.17.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOffseventh

1.3.6.1.4.1.818.1.1.17.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailureseventh

1.3.6.1.4.1.818.1.1.17.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailureseventh

1.3.6.1.4.1.818.1.1.17.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFaultseventh

1.3.6.1.4.1.818.1.1.17.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailedseventh

1.3.6.1.4.1.818.1.1.17.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLostseventh

1.3.6.1.4.1.818.1.1.17.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPowerseventh

1.3.6.1.4.1.818.1.1.17.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPendingseventh

1.3.6.1.4.1.818.1.1.17.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminentseventh

1.3.6.1.4.1.818.1.1.17.6.3.23

The UPS will turn off power to the load in less than 5 sevenths; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgressseventh

1.3.6.1.4.1.818.1.1.17.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOffseventh

1.3.6.1.4.1.818.1.1.17.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailureseventh

1.3.6.1.4.1.818.1.1.17.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailureseventh

1.3.6.1.4.1.818.1.1.17.6.3.27

A High Speed Bus CRC failure on Bus JA is detected.

upsAlarmConnectivityBusFailureseventh

1.3.6.1.4.1.818.1.1.17.6.3.28

A problem on the Connectivity Bus communication is detected.

upsAlarmHighSpeedBusJBCRCFailureseventh

1.3.6.1.4.1.818.1.1.17.6.3.29

A High Speed Bus CRC failure on Bus JB is detected.

upsAlarmCurrentSharingseventh

1.3.6.1.4.1.818.1.1.17.6.3.30

The UPS detects an high current sharing on the parallel system.

upsAlarmDCRippleseventh

1.3.6.1.4.1.818.1.1.17.6.3.31

The UPS detects an high ripple voltage on his DC link.

U32 upsAlarmMaskAseventh

1.3.6.1.4.1.818.1.1.17.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTestseventh

1.3.6.1.4.1.818.1.1.17.7

OID upsTestIdseventh

1.3.6.1.4.1.818.1.1.17.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLockseventh

1.3.6.1.4.1.818.1.1.17.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummaryseventh

1.3.6.1.4.1.818.1.1.17.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetailseventh

1.3.6.1.4.1.818.1.1.17.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTimeseventh

1.3.6.1.4.1.818.1.1.17.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTimeseventh

1.3.6.1.4.1.818.1.1.17.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTestsseventh

1.3.6.1.4.1.818.1.1.17.7.7

upsTestNoTestsInitiatedseventh

1.3.6.1.4.1.818.1.1.17.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgressseventh

1.3.6.1.4.1.818.1.1.17.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTestseventh

1.3.6.1.4.1.818.1.1.17.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTestseventh

1.3.6.1.4.1.818.1.1.17.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibrationseventh

1.3.6.1.4.1.818.1.1.17.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControlseventh

1.3.6.1.4.1.818.1.1.17.8

INT upsShutdownTypeseventh

1.3.6.1.4.1.818.1.1.17.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelayseventh

1.3.6.1.4.1.818.1.1.17.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of sevenths, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of sevenths remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelayseventh

1.3.6.1.4.1.818.1.1.17.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of sevenths, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of sevenths until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDurationseventh

1.3.6.1.4.1.818.1.1.17.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of sevenths, after which time the output will be started, including starting the UPS, if necessary. If the number of sevenths required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 sevenths. When read, upsRebootWithDuration shall return the number of sevenths remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestartseventh

1.3.6.1.4.1.818.1.1.17.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNumseventh

1.3.6.1.4.1.818.1.1.17.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleSeventhTable

1.3.6.1.4.1.818.1.1.17.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleSeventhEntry

1.3.6.1.4.1.818.1.1.17.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndexseventh

1.3.6.1.4.1.818.1.1.17.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOffseventh

1.3.6.1.4.1.818.1.1.17.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSModeseventh

1.3.6.1.4.1.818.1.1.17.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOffseventh

1.3.6.1.4.1.818.1.1.17.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethodseventh

1.3.6.1.4.1.818.1.1.17.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOffseventh

1.3.6.1.4.1.818.1.1.17.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOffseventh

1.3.6.1.4.1.818.1.1.17.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSourceseventh

1.3.6.1.4.1.818.1.1.17.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfigseventh

1.3.6.1.4.1.818.1.1.17.9

NUM upsConfigInputVoltageseventh

1.3.6.1.4.1.818.1.1.17.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreqseventh

1.3.6.1.4.1.818.1.1.17.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltageseventh

1.3.6.1.4.1.818.1.1.17.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreqseventh

1.3.6.1.4.1.818.1.1.17.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVAseventh

1.3.6.1.4.1.818.1.1.17.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPowerseventh

1.3.6.1.4.1.818.1.1.17.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTimeseventh

1.3.6.1.4.1.818.1.1.17.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatusseventh

1.3.6.1.4.1.818.1.1.17.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPointseventh

1.3.6.1.4.1.818.1.1.17.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPointseventh

1.3.6.1.4.1.818.1.1.17.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacityseventh

1.3.6.1.4.1.818.1.1.17.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrentseventh

1.3.6.1.4.1.818.1.1.17.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdownseventh

1.3.6.1.4.1.818.1.1.17.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelayseventh

1.3.6.1.4.1.818.1.1.17.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSetseventh

1.3.6.1.4.1.818.1.1.17.10

NUM upsEventGetNextseventh

1.3.6.1.4.1.818.1.1.17.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPreviousseventh

1.3.6.1.4.1.818.1.1.17.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStampseventh

1.3.6.1.4.1.818.1.1.17.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStampseventh

1.3.6.1.4.1.818.1.1.17.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSizeseventh

1.3.6.1.4.1.818.1.1.17.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventSeventhTable

1.3.6.1.4.1.818.1.1.17.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventSeventhEntry

1.3.6.1.4.1.818.1.1.17.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndexseventh

1.3.6.1.4.1.818.1.1.17.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCodeseventh

1.3.6.1.4.1.818.1.1.17.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatusseventh

1.3.6.1.4.1.818.1.1.17.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTimeseventh

1.3.6.1.4.1.818.1.1.17.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersReadseventh

1.3.6.1.4.1.818.1.1.17.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWriteseventh

1.3.6.1.4.1.818.1.1.17.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the seventh value of the table with the lowest index number.

NUM upsParametersStartAddressseventh

1.3.6.1.4.1.818.1.1.17.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSizeseventh

1.3.6.1.4.1.818.1.1.17.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterSeventhTable

1.3.6.1.4.1.818.1.1.17.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterSeventhEntry

1.3.6.1.4.1.818.1.1.17.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndexseventh

1.3.6.1.4.1.818.1.1.17.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValueseventh

1.3.6.1.4.1.818.1.1.17.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatusseventh

1.3.6.1.4.1.818.1.1.17.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfailseventh

1.3.6.1.4.1.818.1.1.17.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfailseventh

1.3.6.1.4.1.818.1.1.17.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2seventh

1.3.6.1.4.1.818.1.1.17.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5seventh

1.3.6.1.4.1.818.1.1.17.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10seventh

1.3.6.1.4.1.818.1.1.17.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200seventh

1.3.6.1.4.1.818.1.1.17.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypRelseventh

1.3.6.1.4.1.818.1.1.17.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimeseventh

1.3.6.1.4.1.818.1.1.17.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPseventhERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermissionseventh

1.3.6.1.4.1.818.1.1.17.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCodeseventh

1.3.6.1.4.1.818.1.1.17.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLockseventh

1.3.6.1.4.1.818.1.1.17.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLockseventh

1.3.6.1.4.1.818.1.1.17.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTrapsseventh

1.3.6.1.4.1.818.1.1.17.11

NTF upsTrapAlarmBatteryBadseventh

1.3.6.1.4.1.818.1.1.17.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBatteryseventh

1.3.6.1.4.1.818.1.1.17.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBatteryseventh

1.3.6.1.4.1.818.1.1.17.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBatteryseventh

1.3.6.1.4.1.818.1.1.17.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBadseventh

1.3.6.1.4.1.818.1.1.17.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBadseventh

1.3.6.1.4.1.818.1.1.17.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBadseventh

1.3.6.1.4.1.818.1.1.17.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverloadseventh

1.3.6.1.4.1.818.1.1.17.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypassseventh

1.3.6.1.4.1.818.1.1.17.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBadseventh

1.3.6.1.4.1.818.1.1.17.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequestedseventh

1.3.6.1.4.1.818.1.1.17.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequestedseventh

1.3.6.1.4.1.818.1.1.17.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailedseventh

1.3.6.1.4.1.818.1.1.17.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOffseventh

1.3.6.1.4.1.818.1.1.17.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOffseventh

1.3.6.1.4.1.818.1.1.17.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailureseventh

1.3.6.1.4.1.818.1.1.17.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailureseventh

1.3.6.1.4.1.818.1.1.17.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFaultseventh

1.3.6.1.4.1.818.1.1.17.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailedseventh

1.3.6.1.4.1.818.1.1.17.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLostseventh

1.3.6.1.4.1.818.1.1.17.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPowerseventh

1.3.6.1.4.1.818.1.1.17.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPendingseventh

1.3.6.1.4.1.818.1.1.17.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminentseventh

1.3.6.1.4.1.818.1.1.17.11.23

The UPS will turn off power to the load in less than 5 sevenths; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgressseventh

1.3.6.1.4.1.818.1.1.17.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOffseventh

1.3.6.1.4.1.818.1.1.17.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailureseventh

1.3.6.1.4.1.818.1.1.17.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailureseventh

1.3.6.1.4.1.818.1.1.17.11.27

A CRC failure on the Highspeed Bus JA is detected.

NTF upsTrapAlarmConnectivityBusFailureseventh

1.3.6.1.4.1.818.1.1.17.11.28

A problem on the Connectivity Bus communication is detected

NTF upsTrapAlarmHighspeedBusJBCRCFailureseventh

1.3.6.1.4.1.818.1.1.17.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailureseventh

1.3.6.1.4.1.818.1.1.17.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailureseventh

1.3.6.1.4.1.818.1.1.17.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOnseventh

1.3.6.1.4.1.818.1.1.17.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOnseventh

1.3.6.1.4.1.818.1.1.17.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOnseventh

1.3.6.1.4.1.818.1.1.17.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestoreseventh

1.3.6.1.4.1.818.1.1.17.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestoreseventh

1.3.6.1.4.1.818.1.1.17.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestoreseventh

1.3.6.1.4.1.818.1.1.17.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLowseventh

1.3.6.1.4.1.818.1.1.17.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHighseventh

1.3.6.1.4.1.818.1.1.17.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestoredseventh

1.3.6.1.4.1.818.1.1.17.11.134

A ValueHigh alarm condition is restored.

upsDiagnosticseventh

1.3.6.1.4.1.818.1.1.17.12

I32 upsDiagnosticBusJACommunicationStatusseventh

1.3.6.1.4.1.818.1.1.17.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatusseventh

1.3.6.1.4.1.818.1.1.17.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetimeseventh

1.3.6.1.4.1.818.1.1.17.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetimeseventh

1.3.6.1.4.1.818.1.1.17.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetimeseventh

1.3.6.1.4.1.818.1.1.17.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetimeseventh

1.3.6.1.4.1.818.1.1.17.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceCheckseventh

1.3.6.1.4.1.818.1.1.17.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geEighthUPS

1.3.6.1.4.1.818.1.1.18

upsIdenteighth

1.3.6.1.4.1.818.1.1.18.1

STR upsIdentManufacturereighth

1.3.6.1.4.1.818.1.1.18.1.1

DisplayString

read-only

The name of the UPS manufacturer.(*)

STR upsIdentModeleighth

1.3.6.1.4.1.818.1.1.18.1.2

DisplayString

read-only

The UPS Model designation.(*)

STR upsIdentUPSSoftwareVersioneighth

1.3.6.1.4.1.818.1.1.18.1.3

DisplayString

read-only

The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)

STR upsIdentAgentSoftwareVersioneighth

1.3.6.1.4.1.818.1.1.18.1.4

DisplayString

read-only

The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)

STR upsIdentNameeighth

1.3.6.1.4.1.818.1.1.18.1.5

DisplayString

read-write

A string identifying the UPS. This object should be set by the administrator.(*)

STR upsIdentAttachedDeviceseighth

1.3.6.1.4.1.818.1.1.18.1.6

DisplayString

read-write

A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)

STR upsIdentUPSSerialNumbereighth

1.3.6.1.4.1.818.1.1.18.1.7

DisplayString

read-only

The UPS serial number

STR upsIdentComProtVersioneighth

1.3.6.1.4.1.818.1.1.18.1.8

DisplayString

read-only

The IMV communication protocol version

NUM upsIdentOperatingTimeeighth

1.3.6.1.4.1.818.1.1.18.1.9

NonNegativeInteger32

read-only

The present value of the operating time. total 'on' time since UPS manufactured

upsBatteryeighth

1.3.6.1.4.1.818.1.1.18.2

INT upsBatteryStatuseighth

1.3.6.1.4.1.818.1.1.18.2.1

INTEGER

read-only

The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)

NUM upsSecondsOnBatteryeighth

1.3.6.1.4.1.818.1.1.18.2.2

NonNegativeInteger32

read-only

If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)

NUM upsEstimatedMinutesRemainingeighth

1.3.6.1.4.1.818.1.1.18.2.3

PositiveInteger32

read-only

An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)

I32 upsEstimatedChargeRemainingeighth

1.3.6.1.4.1.818.1.1.18.2.4

Integer32

read-only

An estimate of the battery charge remaining expressed as a percent of full charge.(*)

NUM upsBatteryVoltageeighth

1.3.6.1.4.1.818.1.1.18.2.5

NonNegativeInteger32

read-only

The magnitude of the present battery voltage.(*)

I32 upsBatteryCurrenteighth

1.3.6.1.4.1.818.1.1.18.2.6

Integer32

read-only

The present battery current.(*)

I32 upsBatteryTemperatureeighth

1.3.6.1.4.1.818.1.1.18.2.7

Integer32

read-only

The ambient temperature at or near the UPS Battery casing.(*)

I32 upsBatteryRippleeighth

1.3.6.1.4.1.818.1.1.18.2.8

Integer32

read-only

The present DC link RMS voltage ripple.(*)

upsInputeighth

1.3.6.1.4.1.818.1.1.18.3

C32 upsInputLineBadseighth

1.3.6.1.4.1.818.1.1.18.3.1

Counter32

read-only

A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)

NUM upsInputNumLineseighth

1.3.6.1.4.1.818.1.1.18.3.2

NonNegativeInteger32

read-only

The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)

upsInputEighthTable

1.3.6.1.4.1.818.1.1.18.3.3

not-accessible

A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)

upsInputEighthEntry

1.3.6.1.4.1.818.1.1.18.3.3.1

not-accessible

An entry containing information applicable to a particular input line.(*)

NUM upsInputLineIndexeighth

1.3.6.1.4.1.818.1.1.18.3.3.1.1

PositiveInteger32

not-accessible

The input line identifier.(*)

NUM upsInputFrequencyeighth

1.3.6.1.4.1.818.1.1.18.3.3.1.2

NonNegativeInteger32

read-only

The present input frequency.(*)

NUM upsInputVoltageeighth

1.3.6.1.4.1.818.1.1.18.3.3.1.3

NonNegativeInteger32

read-only

The magnitude of the present input voltage.(*)

NUM upsInputCurrenteighth

1.3.6.1.4.1.818.1.1.18.3.3.1.4

NonNegativeInteger32

read-only

The magnitude of the present input current.(*)

NUM upsInputTruePowereighth

1.3.6.1.4.1.818.1.1.18.3.3.1.5

NonNegativeInteger32

read-only

The magnitude of the present input true power.(*)

NUM upsInputVoltageMineighth

1.3.6.1.4.1.818.1.1.18.3.3.1.6

NonNegativeInteger32

read-only

The lowest magnitude of the input voltage since last read out.

NUM upsInputVoltageMaxeighth

1.3.6.1.4.1.818.1.1.18.3.3.1.7

NonNegativeInteger32

read-only

The highest magnitude of the input voltage since last read out.

upsOutputeighth

1.3.6.1.4.1.818.1.1.18.4

INT upsOutputSourceeighth

1.3.6.1.4.1.818.1.1.18.4.1

INTEGER

read-only

The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)

NUM upsOutputFrequencyeighth

1.3.6.1.4.1.818.1.1.18.4.2

NonNegativeInteger32

read-only

The present output frequency.(*)

NUM upsOutputNumLineseighth

1.3.6.1.4.1.818.1.1.18.4.3

NonNegativeInteger32

read-only

The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)

upsOutputEighthTable

1.3.6.1.4.1.818.1.1.18.4.4

not-accessible

A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)

upsOutputEighthEntry

1.3.6.1.4.1.818.1.1.18.4.4.1

not-accessible

An entry containing information applicable to a particular output line.(*)

NUM upsOutputLineIndexeighth

1.3.6.1.4.1.818.1.1.18.4.4.1.1

PositiveInteger32

not-accessible

The output line identifier.(*)

NUM upsOutputVoltageeighth

1.3.6.1.4.1.818.1.1.18.4.4.1.2

NonNegativeInteger32

read-only

The present output voltage.(*)

NUM upsOutputCurrenteighth

1.3.6.1.4.1.818.1.1.18.4.4.1.3

NonNegativeInteger32

read-only

The present output current.(*)

NUM upsOutputPowereighth

1.3.6.1.4.1.818.1.1.18.4.4.1.4

NonNegativeInteger32

read-only

The present output true power.(*)

I32 upsOutputPercentLoadeighth

1.3.6.1.4.1.818.1.1.18.4.4.1.5

Integer32

read-only

The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)

I32 upsOutputPowerFactoreighth

1.3.6.1.4.1.818.1.1.18.4.4.1.6

Integer32

read-only

The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If the measure is not available due to a small load for a consistent calculation, the NA value is then returned.(*)

I32 upsOutputPeakCurrenteighth

1.3.6.1.4.1.818.1.1.18.4.4.1.7

Integer32

read-only

The present output peak current.(*)

I32 upsOutputShareCurrenteighth

1.3.6.1.4.1.818.1.1.18.4.4.1.8

Integer32

read-only

In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UPS, so that this current component doesn't feed the load. The share part of the UPS current represents an undesired UPS loading, and therefore it should be minimized. If the share current is too high, the UPS results overloaded and in some conditions (i.e. very high load) the system could turn on bypass reducing dramatically the global system reliability. PMAD detects the amount of share currents in a parallel system, generating an alarm if this value is above a parameter-based threshold. Single UPS systems don't have this feature, NA will be provided.(*)

upsBypasseighth

1.3.6.1.4.1.818.1.1.18.5

NUM upsBypassFrequencyeighth

1.3.6.1.4.1.818.1.1.18.5.1

NonNegativeInteger32

read-only

The present bypass frequency.(*)

NUM upsBypassNumLineseighth

1.3.6.1.4.1.818.1.1.18.5.2

NonNegativeInteger32

read-only

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)

upsBypassEighthTable

1.3.6.1.4.1.818.1.1.18.5.3

not-accessible

A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)

upsBypassEighthEntry

1.3.6.1.4.1.818.1.1.18.5.3.1

not-accessible

An entry containing information applicable to a particular bypass input.(*)

NUM upsBypassLineIndexeighth

1.3.6.1.4.1.818.1.1.18.5.3.1.1

PositiveInteger32

not-accessible

The bypass line identifier.(*)

NUM upsBypassVoltageeighth

1.3.6.1.4.1.818.1.1.18.5.3.1.2

NonNegativeInteger32

read-only

The present bypass voltage.(*)

NUM upsBypassCurrenteighth

1.3.6.1.4.1.818.1.1.18.5.3.1.3

NonNegativeInteger32

read-only

The present bypass current.(*)

NUM upsBypassPowereighth

1.3.6.1.4.1.818.1.1.18.5.3.1.4

NonNegativeInteger32

read-only

The present true power conveyed by the bypass.(*)

upsAlarmeighth

1.3.6.1.4.1.818.1.1.18.6

G32 upsAlarmsPresenteighth

1.3.6.1.4.1.818.1.1.18.6.1

Gauge32

read-only

The present number of active alarm conditions.(*)

upsAlarmEighthTable

1.3.6.1.4.1.818.1.1.18.6.2

not-accessible

A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)

upsAlarmEighthEntry

1.3.6.1.4.1.818.1.1.18.6.2.1

not-accessible

An entry containing information applicable to a particular alarm.(*)

NUM upsAlarmIdeighth

1.3.6.1.4.1.818.1.1.18.6.2.1.1

PositiveInteger32

not-accessible

A unique identifier for an alarm condition. This value must remain constant.(*)

OID upsAlarmDescreighth

1.3.6.1.4.1.818.1.1.18.6.2.1.2

AutonomousType

read-only

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)

TIM upsAlarmTimeeighth

1.3.6.1.4.1.818.1.1.18.6.2.1.3

TimeStamp

read-only

The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)

upsWellKnownAlarmseighth

1.3.6.1.4.1.818.1.1.18.6.3

upsAlarmBatteryBadeighth

1.3.6.1.4.1.818.1.1.18.6.3.1

One or more batteries have been determined to require replacement.(*)

upsAlarmOnBatteryeighth

1.3.6.1.4.1.818.1.1.18.6.3.2

The UPS is drawing power from the batteries.(*)

upsAlarmLowBatteryeighth

1.3.6.1.4.1.818.1.1.18.6.3.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)

upsAlarmDepletedBatteryeighth

1.3.6.1.4.1.818.1.1.18.6.3.4

The UPS will be unable to sustain the present load when and if the utility power is lost.(*)

upsAlarmTempBadeighth

1.3.6.1.4.1.818.1.1.18.6.3.5

A temperature is out of tolerance.(*)

upsAlarmInputBadeighth

1.3.6.1.4.1.818.1.1.18.6.3.6

An input condition is out of tolerance.(*)

upsAlarmOutputBadeighth

1.3.6.1.4.1.818.1.1.18.6.3.7

An output condition (other than OutputOverload) is out of tolerance.(*)

upsAlarmOutputOverloadeighth

1.3.6.1.4.1.818.1.1.18.6.3.8

The output load exceeds the UPS output capacity.(*)

upsAlarmOnBypasseighth

1.3.6.1.4.1.818.1.1.18.6.3.9

The Bypass is presently engaged on the UPS.(*)

upsAlarmBypassBadeighth

1.3.6.1.4.1.818.1.1.18.6.3.10

The Bypass is out of tolerance.(*)

upsAlarmOutputOffAsRequestedeighth

1.3.6.1.4.1.818.1.1.18.6.3.11

The UPS has shutdown as requested, i.e., the output is off.(*)

upsAlarmUpsOffAsRequestedeighth

1.3.6.1.4.1.818.1.1.18.6.3.12

The entire UPS has shutdown as commanded.(*)

upsAlarmChargerFailedeighth

1.3.6.1.4.1.818.1.1.18.6.3.13

An uncorrected problem has been detected within the UPS charger subsystem.(*)

upsAlarmUpsOutputOffeighth

1.3.6.1.4.1.818.1.1.18.6.3.14

The output of the UPS is in the off state.(*)

upsAlarmUpsSystemOffeighth

1.3.6.1.4.1.818.1.1.18.6.3.15

The UPS system is in the off state.(*)

upsAlarmFanFailureeighth

1.3.6.1.4.1.818.1.1.18.6.3.16

The failure of one or more fans in the UPS has been detected.(*)

upsAlarmFuseFailureeighth

1.3.6.1.4.1.818.1.1.18.6.3.17

The failure of one or more fuses has been detected.(*)

upsAlarmGeneralFaulteighth

1.3.6.1.4.1.818.1.1.18.6.3.18

A general fault in the UPS has been detected.(*)

upsAlarmDiagnosticTestFailedeighth

1.3.6.1.4.1.818.1.1.18.6.3.19

The result of the last diagnostic test indicates a failure.(*)

upsAlarmCommunicationsLosteighth

1.3.6.1.4.1.818.1.1.18.6.3.20

A problem has been encountered in the communications between the agent and the UPS.(*)

upsAlarmAwaitingPowereighth

1.3.6.1.4.1.818.1.1.18.6.3.21

The UPS output is off and the UPS is awaiting the return of input power.(*)

upsAlarmShutdownPendingeighth

1.3.6.1.4.1.818.1.1.18.6.3.22

A upsShutdownAfterDelay countdown is underway.(*)

upsAlarmShutdownImminenteighth

1.3.6.1.4.1.818.1.1.18.6.3.23

The UPS will turn off power to the load in less than 5 eighths; this may be either a timed shutdown or a low battery shutdown.(*)

upsAlarmTestInProgresseighth

1.3.6.1.4.1.818.1.1.18.6.3.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)

upsAlarmReceptacleOffeighth

1.3.6.1.4.1.818.1.1.18.6.3.25

The receptacle are switch off

upsAlarmHighSpeedBusFailureeighth

1.3.6.1.4.1.818.1.1.18.6.3.26

A problem on the High Speed Bus communication is detected

upsAlarmHighSpeedBusJACRCFailureeighth

1.3.6.1.4.1.818.1.1.18.6.3.27

A High Speed Bus CRC failure on Bus JA is detected.

upsAlarmConnectivityBusFailureeighth

1.3.6.1.4.1.818.1.1.18.6.3.28

A problem on the Connectivity Bus communication is detected

upsAlarmHighSpeedBusJBCRCFailureeighth

1.3.6.1.4.1.818.1.1.18.6.3.29

A High Speed Bus CRC failure on Bus JB is detected.

upsAlarmCurrentSharingeighth

1.3.6.1.4.1.818.1.1.18.6.3.30

The UPS detects an high current sharing on the parallel system.

upsAlarmDCRippleeighth

1.3.6.1.4.1.818.1.1.18.6.3.31

The UPS detects an high ripple voltage on his DC link.

U32 upsAlarmMaskAeighth

1.3.6.1.4.1.818.1.1.18.6.4

Unsigned32

read-only

Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.

upsTesteighth

1.3.6.1.4.1.818.1.1.18.7

OID upsTestIdeighth

1.3.6.1.4.1.818.1.1.18.7.1

OBJECT IDENTIFIER

read-write

The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)

TES upsTestSpinLockeighth

1.3.6.1.4.1.818.1.1.18.7.2

TestAndIncr

read-write

A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: tryagain: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lockvalue = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lockvalue, upsTestId = requestedtest) if (errorindex == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto tryagain } if (errorindex == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lockvalue + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.(*)

INT upsTestResultsSummaryeighth

1.3.6.1.4.1.818.1.1.18.7.3

INTEGER

read-only

The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)

STR upsTestResultsDetaileighth

1.3.6.1.4.1.818.1.1.18.7.4

DisplayString

read-only

Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)

TIM upsTestStartTimeeighth

1.3.6.1.4.1.818.1.1.18.7.5

TimeStamp

read-only

The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)

NUM upsTestElapsedTimeeighth

1.3.6.1.4.1.818.1.1.18.7.6

TimeInterval

read-only

The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)

upsWellKnownTestseighth

1.3.6.1.4.1.818.1.1.18.7.7

upsTestNoTestsInitiatedeighth

1.3.6.1.4.1.818.1.1.18.7.7.1

No tests have been initiated and no test is in progress.(*)

upsTestAbortTestInProgresseighth

1.3.6.1.4.1.818.1.1.18.7.7.2

The test in progress is to be aborted / the test in progress was aborted.(*)

upsTestGeneralSystemsTesteighth

1.3.6.1.4.1.818.1.1.18.7.7.3

The manufacturer's standard test of UPS device systems.(*)

upsTestQuickBatteryTesteighth

1.3.6.1.4.1.818.1.1.18.7.7.4

A test that is sufficient to determine if the battery needs replacement.(*)

upsTestDeepBatteryCalibrationeighth

1.3.6.1.4.1.818.1.1.18.7.7.5

The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)

upsControleighth

1.3.6.1.4.1.818.1.1.18.8

INT upsShutdownTypeeighth

1.3.6.1.4.1.818.1.1.18.8.1

INTEGER

read-write

This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)

I32 upsShutdownAfterDelayeighth

1.3.6.1.4.1.818.1.1.18.8.2

Integer32

read-write

Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of eighths, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of eighths remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)

I32 upsStartupAfterDelayeighth

1.3.6.1.4.1.818.1.1.18.8.3

Integer32

read-write

Setting this object will start the output after the indicated number of eighths, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of eighths until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)

I32 upsRebootWithDurationeighth

1.3.6.1.4.1.818.1.1.18.8.4

Integer32

read-write

Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of eighths, after which time the output will be started, including starting the UPS, if necessary. If the number of eighths required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 eighths. When read, upsRebootWithDuration shall return the number of eighths remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)

INT upsAutoRestarteighth

1.3.6.1.4.1.818.1.1.18.8.5

INTEGER

read-write

Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)

NUM upsReceptaclesNumeighth

1.3.6.1.4.1.818.1.1.18.8.6

NonNegativeInteger32

read-only

The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.

upsReceptacleEighthTable

1.3.6.1.4.1.818.1.1.18.8.7

not-accessible

A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.

upsReceptacleEighthEntry

1.3.6.1.4.1.818.1.1.18.8.7.1

not-accessible

An entry containing information applicable to a particular receptacle.

NUM upsReceptacleLineIndexeighth

1.3.6.1.4.1.818.1.1.18.8.7.1.1

PositiveInteger32

not-accessible

The receptacle line identifier.

INT upsReceptacleOnOffeighth

1.3.6.1.4.1.818.1.1.18.8.7.1.2

INTEGER

read-write

The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.

INT upsUPSModeeighth

1.3.6.1.4.1.818.1.1.18.8.8

INTEGER

read-write

The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)

INT upsRectifierOnOffeighth

1.3.6.1.4.1.818.1.1.18.8.9

INTEGER

read-write

The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.

INT upsBatteryChargeMethodeighth

1.3.6.1.4.1.818.1.1.18.8.10

INTEGER

read-write

The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.

INT upsInverterOnOffeighth

1.3.6.1.4.1.818.1.1.18.8.11

INTEGER

read-write

The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.

INT upsBypassOnOffeighth

1.3.6.1.4.1.818.1.1.18.8.12

INTEGER

read-write

The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.

INT upsLoadSourceeighth

1.3.6.1.4.1.818.1.1.18.8.13

INTEGER

read-write

The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.

upsConfigeighth

1.3.6.1.4.1.818.1.1.18.9

NUM upsConfigInputVoltageeighth

1.3.6.1.4.1.818.1.1.18.9.1

NonNegativeInteger32

read-write

The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigInputFreqeighth

1.3.6.1.4.1.818.1.1.18.9.2

NonNegativeInteger32

read-write

The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVoltageeighth

1.3.6.1.4.1.818.1.1.18.9.3

NonNegativeInteger32

read-write

The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputFreqeighth

1.3.6.1.4.1.818.1.1.18.9.4

NonNegativeInteger32

read-write

The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)

NUM upsConfigOutputVAeighth

1.3.6.1.4.1.818.1.1.18.9.5

NonNegativeInteger32

read-only

The magnitude of the nominal Volt-Amp rating.(*)

NUM upsConfigOutputPowereighth

1.3.6.1.4.1.818.1.1.18.9.6

NonNegativeInteger32

read-only

The magnitude of the nominal true power rating.(*)

NUM upsConfigLowBattTimeeighth

1.3.6.1.4.1.818.1.1.18.9.7

NonNegativeInteger32

read-write

The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)

INT upsConfigAudibleStatuseighth

1.3.6.1.4.1.818.1.1.18.9.8

INTEGER

read-write

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)

NUM upsConfigLowVoltageTransferPointeighth

1.3.6.1.4.1.818.1.1.18.9.9

NonNegativeInteger32

read-write

The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigHighVoltageTransferPointeighth

1.3.6.1.4.1.818.1.1.18.9.10

NonNegativeInteger32

read-write

The maximum line voltage allowed before the UPS system transfers to battery backup.(*)

NUM upsConfigBatteryCapacityeighth

1.3.6.1.4.1.818.1.1.18.9.11

NonNegativeInteger32

read-write

The installed battery capacity. This value is the 'factory'-value, not the value after calibration.

NUM upsConfigBatteryChargeCurrenteighth

1.3.6.1.4.1.818.1.1.18.9.12

NonNegativeInteger32

read-write

The maximum battery charge current, including external chargers.

INT upsConfigNoLoadShutdowneighth

1.3.6.1.4.1.818.1.1.18.9.13

INTEGER

read-write

Dis- or enable 'no load' shutdown from the contact interface.

NUM upsConfigStartDelayeighth

1.3.6.1.4.1.818.1.1.18.9.14

PositiveInteger32

read-write

Minimum required autonomy time before the UPS may perform an autorestart.

upsGetSeteighth

1.3.6.1.4.1.818.1.1.18.10

NUM upsEventGetNexteighth

1.3.6.1.4.1.818.1.1.18.10.1

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.

NUM upsEventGetPreviouseighth

1.3.6.1.4.1.818.1.1.18.10.2

PositiveInteger32

read-write

The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMPNOSUCHNAME for UPSs that don't support this command.

NUM upsEventSetStartingTimeStampeighth

1.3.6.1.4.1.818.1.1.18.10.3

NonNegativeInteger32

read-write

The timestamp which is used as starting point for downloading events from the UPS event buffer

NUM upsEventRetreiveCurrentTimeStampeighth

1.3.6.1.4.1.818.1.1.18.10.4

NonNegativeInteger32

read-only

The current timestamp is retreived from the UPS

NUM upsEventTableSizeeighth

1.3.6.1.4.1.818.1.1.18.10.5

NonNegativeInteger32

read-only

The number of entries in the event table. This object indicates the number of rows in the event table.

upsEventEighthTable

1.3.6.1.4.1.818.1.1.18.10.6

not-accessible

A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.

upsEventEighthEntry

1.3.6.1.4.1.818.1.1.18.10.6.1

not-accessible

An entry containing information applicable to a particular event.

NUM upsEventLineIndexeighth

1.3.6.1.4.1.818.1.1.18.10.6.1.1

PositiveInteger32

not-accessible

The event line identifier.

I32 upsEventCodeeighth

1.3.6.1.4.1.818.1.1.18.10.6.1.2

Integer32

read-only

The event code in numerical format.

NUM upsEventStatuseighth

1.3.6.1.4.1.818.1.1.18.10.6.1.3

NonNegativeInteger32

read-only

The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.

NUM upsEventTimeeighth

1.3.6.1.4.1.818.1.1.18.10.6.1.4

NonNegativeInteger32

read-only

The timestamp of the moment the event was generated.

NUM upsParametersReadeighth

1.3.6.1.4.1.818.1.1.18.10.7

PositiveInteger32

read-write

The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.

NUM upsParametersWriteeighth

1.3.6.1.4.1.818.1.1.18.10.8

PositiveInteger32

read-write

The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the eighth value of the table with the lowest index number.

NUM upsParametersStartAddresseighth

1.3.6.1.4.1.818.1.1.18.10.9

NonNegativeInteger32

read-write

The address which is used as starting point for downloading parameters from the UPS

NUM upsParameterTableSizeeighth

1.3.6.1.4.1.818.1.1.18.10.10

NonNegativeInteger32

read-only

The number of entries in the parameter table. This object indicates the number of rows in the parameter table.

upsParameterEighthTable

1.3.6.1.4.1.818.1.1.18.10.11

not-accessible

A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite

upsParameterEighthEntry

1.3.6.1.4.1.818.1.1.18.10.11.1

not-accessible

An entry containing information applicable to a particular parameter.

NUM upsParameterLineIndexeighth

1.3.6.1.4.1.818.1.1.18.10.11.1.1

PositiveInteger32

not-accessible

The parameter line identifier.

I32 upsParameterValueeighth

1.3.6.1.4.1.818.1.1.18.10.11.1.2

Integer32

read-write

The parameter value in numerical format.

NUM upsStatuseighth

1.3.6.1.4.1.818.1.1.18.10.12

NonNegativeInteger32

read-only

The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMPNOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0000 0001h upsStatusEcomodeIsOn 2 0000 0002h upsStatusBatteryIsCharging 4 0000 0004h upsStatusBatteryIsDischarging 8 0000 0008h upsStatusAlarmIsActive 16 0000 0010h upsStatusRectifierIsOn 32 0000 0020h upsStatusLowBattery 64 0000 0040h upsStatusOnBypass 128 0000 0080h upsStatusMainsBypassOK 256 0000 0100h upsStatusMainsRectifierOK 512 0000 0200h upsStatusDetourIsOn 1024 0000 0400h upsStatusAcousticAlarmIsOn 2048 0000 0800h upsStatusGlobalServiceCheck 4096 0000 1000h upsStatusInverterIsOn 8192 0000 2000h upsStatusNotInParallel (Q1 open) 16384 0000 4000h upsStatusResetLoadOff 32768 0000 8000h upsStatusLoadOff 65536 0001 0000h upsStatusBoostMode 131072 0002 0000h upsStatusBuckMode 262144 0004 0000h upsStatusIemModeIsOn 524288 0008 0000h upsStatus5thFilterIsOn 1048576 0010 0000h upsStatus11thFilterIsOn 2097152 0020 0000h upsStatus2ndRectifierBridgeIsOn 4194304 0040 0000h - reserved - 8388608 0080 0000h - reserved - 16777216 0100 0000h - reserved - 33554432 0200 0000h - reserved - 67108864 0400 0000h - reserved - 134217728 0800 0000h - reserved - 268435456 1000 0000h upsGlobalParallelValues

NUM upsMainsStatisticsMBfaileighth

1.3.6.1.4.1.818.1.1.18.10.13

NonNegativeInteger32

read-only

Count of main bypass failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsMRfaileighth

1.3.6.1.4.1.818.1.1.18.10.14

NonNegativeInteger32

read-only

Count of mains rectifier failures (>200 ms), since UPS installation.

NUM upsMainsStatisticsB2eighth

1.3.6.1.4.1.818.1.1.18.10.15

NonNegativeInteger32

read-only

Count of transients on the mains bypass (0..2 ms), during the last 7 days.

NUM upsMainsStatisticsB5eighth

1.3.6.1.4.1.818.1.1.18.10.16

NonNegativeInteger32

read-only

Count of transients on the mains bypass (2..5 ms), during the last 7 days.

NUM upsMainsStatisticsB10eighth

1.3.6.1.4.1.818.1.1.18.10.17

NonNegativeInteger32

read-only

Count of transients on the mains bypass (5..10 ms), during the last 7 days.

NUM upsMainsStatisticsB200eighth

1.3.6.1.4.1.818.1.1.18.10.18

NonNegativeInteger32

read-only

Count of transients on the mains bypass (10..200 ms), during the last 7 days.

NUM upsMainsStatisticsBypReleighth

1.3.6.1.4.1.818.1.1.18.10.19

NonNegativeInteger32

read-only

Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.

NUM upsTimeeighth

1.3.6.1.4.1.818.1.1.18.10.20

NonNegativeInteger32

read-write

The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMPeighthERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.

STR upsRequestPermissioneighth

1.3.6.1.4.1.818.1.1.18.10.21

DisplayString

read-write

An encrypted code is send to enable use of restricted write objects during a limited period of time.

I32 upsEventGetCodeeighth

1.3.6.1.4.1.818.1.1.18.10.22

Integer32

read-write

The code which is used as starting point to downloading the events from the UPS event buffer.

TES upsEventSpinLockeighth

1.3.6.1.4.1.818.1.1.18.10.23

TestAndIncr

read-write

A spin lock on the event subsystem.

TES upsParameterSpinLockeighth

1.3.6.1.4.1.818.1.1.18.10.24

TestAndIncr

read-write

A spin lock on the parameters subsystem.

geUPSTrapseighth

1.3.6.1.4.1.818.1.1.18.11

NTF upsTrapAlarmBatteryBadeighth

1.3.6.1.4.1.818.1.1.18.11.1

One or more batteries have been determined to require replacement.

NTF upsTrapAlarmOnBatteryeighth

1.3.6.1.4.1.818.1.1.18.11.2

The UPS is drawing power from the batteries.

NTF upsTrapAlarmLowBatteryeighth

1.3.6.1.4.1.818.1.1.18.11.3

The remaining battery run-time is less than or equal to upsConfigLowBattTime.

NTF upsTrapAlarmDepletedBatteryeighth

1.3.6.1.4.1.818.1.1.18.11.4

The UPS will be unable to sustain the present load when and if the utility power is lost)

NTF upsTrapAlarmTempBadeighth

1.3.6.1.4.1.818.1.1.18.11.5

A temperature is out of tolerance.

NTF upsTrapAlarmInputBadeighth

1.3.6.1.4.1.818.1.1.18.11.6

An input condition is out of tolerance.

NTF upsTrapAlarmOutputBadeighth

1.3.6.1.4.1.818.1.1.18.11.7

An output condition (other than OutputOverload) is out of tolerance.

NTF upsTrapAlarmOutputOverloadeighth

1.3.6.1.4.1.818.1.1.18.11.8

The output load exceeds the UPS output capacity.

NTF upsTrapAlarmOnBypasseighth

1.3.6.1.4.1.818.1.1.18.11.9

The Bypass is presently engaged on the UPS.

NTF upsTrapAlarmBypassBadeighth

1.3.6.1.4.1.818.1.1.18.11.10

The Bypass is out of tolerance.

NTF upsTrapAlarmOutputOffAsRequestedeighth

1.3.6.1.4.1.818.1.1.18.11.11

The UPS has shutdown as requested, i.e., the output is off.

NTF upsTrapAlarmUpsOffAsRequestedeighth

1.3.6.1.4.1.818.1.1.18.11.12

The entire UPS has shutdown as commanded.

NTF upsTrapAlarmChargerFailedeighth

1.3.6.1.4.1.818.1.1.18.11.13

An uncorrected problem has been detected within the UPS charger subsystem.

NTF upsTrapAlarmUpsOutputOffeighth

1.3.6.1.4.1.818.1.1.18.11.14

The output of the UPS is in the off state.

NTF upsTrapAlarmUpsSystemOffeighth

1.3.6.1.4.1.818.1.1.18.11.15

The UPS system is in the off state.

NTF upsTrapAlarmFanFailureeighth

1.3.6.1.4.1.818.1.1.18.11.16

The failure of one or more fans in the UPS has been detected.

NTF upsTrapAlarmFuseFailureeighth

1.3.6.1.4.1.818.1.1.18.11.17

The failure of one or more fuses has been detected.

NTF upsTrapAlarmGeneralFaulteighth

1.3.6.1.4.1.818.1.1.18.11.18

A general fault in the UPS has been detected.

NTF upsTrapAlarmDiagnosticTestFailedeighth

1.3.6.1.4.1.818.1.1.18.11.19

The result of the last diagnostic test indicates a failure.

NTF upsTrapAlarmCommunicationsLosteighth

1.3.6.1.4.1.818.1.1.18.11.20

A problem has been encountered in the communication between the agent and the UPS.

NTF upsTrapAlarmAwaitingPowereighth

1.3.6.1.4.1.818.1.1.18.11.21

The UPS output is off and the UPS is awaiting the return of the input power (*).

NTF upsTrapAlarmShutdownPendingeighth

1.3.6.1.4.1.818.1.1.18.11.22

A upsShutdownAfterDelay countdown is underway.

NTF upsTrapAlarmShutdownImminenteighth

1.3.6.1.4.1.818.1.1.18.11.23

The UPS will turn off power to the load in less than 5 eighths; this may be either a timed shutdown or a low battery shutdown.

NTF upsTrapAlarmTestInProgresseighth

1.3.6.1.4.1.818.1.1.18.11.24

A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.

NTF upsTrapAlarmReceptacleOffeighth

1.3.6.1.4.1.818.1.1.18.11.25

A receptacle has been switched off.

NTF upsTrapAlarmHighspeedBusFailureeighth

1.3.6.1.4.1.818.1.1.18.11.26

A problem on the Highspeed Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJACRCFailureeighth

1.3.6.1.4.1.818.1.1.18.11.27

A CRC failure on the Highspeed Bus JA is detected.

NTF upsTrapAlarmConnectivityBusFailureeighth

1.3.6.1.4.1.818.1.1.18.11.28

A problem on the Connectivity Bus communication is detected.

NTF upsTrapAlarmHighspeedBusJBCRCFailureeighth

1.3.6.1.4.1.818.1.1.18.11.29

A CRC failure on the Highspeed Bus JB is detected.

NTF upsTrapAlarmCurrentSharingFailureeighth

1.3.6.1.4.1.818.1.1.18.11.30

An high current sharing on the parallel system is detected.

NTF upsTrapAlarmDCRippleFailureeighth

1.3.6.1.4.1.818.1.1.18.11.31

An high ripple voltage on his DC link is detected.

NTF upsTrapAlarmBatteryBadRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.33

A Battery bad condition is restored.

NTF upsTrapAlarmOnBatteryRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.34

The UPS is drawing power from mains again.

NTF upsTrapAlarmLowBatteryRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.35

A Low Battery condition is restored.

NTF upsTrapAlarmDepletedBatteryRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.36

A Depleted Battery condition is restored.

NTF upsTrapAlarmTempBadRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.37

A bad temperature condition is restored.

NTF upsTrapAlarmInputBadRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.38

An input bad condition is restored.

NTF upsTrapAlarmOutputBadRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.39

An output bad condition is restored.

NTF upsTrapAlarmOutputOverloadRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.40

An output overload condition is restored.

NTF upsTrapAlarmOnBypassRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.41

An On Bypass condition is restored.

NTF upsTrapAlarmBypassBadRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.42

A Bypass bad condition is restored.

NTF upsTrapAlarmOutputOffAsRequestedRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.43

A request shutdown has been restored.

NTF upsTrapAlarmUpsOffAsRequestedRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.44

A entire UPS command has been restored.

NTF upsTrapAlarmChargerFailedRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.45

A Charger Failer condition is restored.

NTF upsTrapAlarmUpsOutputOneighth

1.3.6.1.4.1.818.1.1.18.11.46

The output of the UPS switched in the on state.

NTF upsTrapAlarmUpsSystemOneighth

1.3.6.1.4.1.818.1.1.18.11.47

The UPS system is switched in the on state.

NTF upsTrapAlarmFanFailureRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.48

A Fan failure condition is restored.

NTF upsTrapAlarmFuseFailureRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.49

A Fuse failure condition is restored.

NTF upsTrapAlarmGeneralFaultRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.50

A general fault is restored.

NTF upsTrapAlarmDiagnosticTestFailedRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.51

A last diagnostic test indicates a failure is restored.

NTF upsTrapAlarmCommunicationsLostRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.52

A problem in the communication between the agent and the UPS is restored.

NTF upsTrapAlarmAwaitingPowerRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.53

A awaiting power condition is restored (*).

NTF upsTrapAlarmShutdownPendingRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.54

A upsShutdownAfterDelay countdown is restored.

NTF upsTrapAlarmShutdownImminentRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.55

A shutdown imminent condition is restored.

NTF upsTrapAlarmTestInProgressRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.56

The test is in progress is terminated.

NTF upsTrapAlarmReceptacleOneighth

1.3.6.1.4.1.818.1.1.18.11.57

A receptacle has been switched on.

NTF upsTrapAlarmHighspeedBusRestoreeighth

1.3.6.1.4.1.818.1.1.18.11.58

A problem on the Highspeed Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJACRCRestoreeighth

1.3.6.1.4.1.818.1.1.18.11.59

A CRC failure on the Highspeed Bus JA is restored.

NTF upsTrapAlarmConnectivityBusRestoreeighth

1.3.6.1.4.1.818.1.1.18.11.60

A problem on the Connectivity Bus communication is restored.

NTF upsTrapAlarmHighspeedBusJBCRCRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.61

A CRC failure on the Highspeed Bus JB is restored.

NTF upsTrapAlarmCurrentSharingRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.62

An high current sharing on the parallel system is restored.

NTF upsTrapAlarmDCRippleRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.63

An high ripple voltage on his DC link is restored.

NTF upsTrapAlarmValueLoweighth

1.3.6.1.4.1.818.1.1.18.11.129

A measurement value reached a value below its low-level threshold.

NTF upsTrapAlarmValueHigheighth

1.3.6.1.4.1.818.1.1.18.11.130

A measurement value reached a value higher than its high-level threshold.

NTF upsTrapAlarmValueLowRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.133

A ValueLow alarm condition is restored.

NTF upsTrapAlarmValueHighRestoredeighth

1.3.6.1.4.1.818.1.1.18.11.134

A ValueHigh alarm condition is restored.

upsDiagnosticeighth

1.3.6.1.4.1.818.1.1.18.12

I32 upsDiagnosticBusJACommunicationStatuseighth

1.3.6.1.4.1.818.1.1.18.12.1

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBusJBCommunicationStatuseighth

1.3.6.1.4.1.818.1.1.18.12.2

Integer32

read-only

Bit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA if bit=0.(*)

I32 upsDiagnosticBatteryLifetimeeighth

1.3.6.1.4.1.818.1.1.18.12.3

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticFansLifetimeeighth

1.3.6.1.4.1.818.1.1.18.12.4

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticDCcapacitorsLifetimeeighth

1.3.6.1.4.1.818.1.1.18.12.5

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticACcapacitorsLifetimeeighth

1.3.6.1.4.1.818.1.1.18.12.6

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

I32 upsDiagnosticGlobalServiceCheckeighth

1.3.6.1.4.1.818.1.1.18.12.7

Integer32

read-only

The critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data given by the component supplier. The parameter values decrease over time and when one of them reaches zero (lifetime expiration) a service check warning is generated, indicating that a check or a replacement is suggested for that component. The service technician is then required to re-set the default value after the replacing of the component.(*)

geDevices

1.3.6.1.4.1.818.1.100

geDevicesDescriptions

1.3.6.1.4.1.818.1.100.1

advSNMPWebIntCard

1.3.6.1.4.1.818.1.100.1.1

snmpWebIntCard

1.3.6.1.4.1.818.1.100.1.2

snmpWebIntBox

1.3.6.1.4.1.818.1.100.1.3