LIEBERT-UPS-MIB

All MIBs › LIEBERT-UPS-MIB

Category: Domain: Power/UPS, Vendor: Liebert

Description: General Liebert UPS SNMP MIB providing battery status, input/output voltage, load, and alarm objects for uninterruptible power supplies.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is LIEBERT-UPS-MIB?

LIEBERT-UPS-MIB is a general-purpose Liebert (now Vertiv) enterprise MIB for monitoring uninterruptible power supply (UPS) units, covering battery status, input and output voltage, load level, and alarm conditions. Its data categories are squarely environmental/power-health: battery state of charge and condition, AC input/output voltage readings, present load as a percentage of capacity, and a set of alarm objects for fault conditions such as on-battery operation, low battery, or overload. This is directly a hardware-health monitoring MIB -- battery status and alarm objects are exactly what an operator watches to know whether the UPS is running normally on utility power, has switched to battery during an outage, or is approaching battery depletion, all critical for protecting the equipment it powers. No sample objects were available for this module to confirm exact naming, but the described scope aligns with the standard structure common to UPS MIBs (battery, input, output, alarm groups). It is deployed on Liebert UPS units protecting data center, telecom, and critical-facility equipment from power interruptions. Network engineers evaluating or troubleshooting this functionality can download the LIEBERT-UPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in LIEBERT-UPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Liebert (Vertiv) UPS units

Monitoring Examples

Because no sample objects were provided, a fully object-grounded example cannot be given with certainty; in general, a facilities engineer would poll the UPS's battery status and alarm objects to confirm whether the unit is on utility power or has switched to battery. They would also check output load and voltage objects to ensure the UPS isn't approaching its rated capacity. A battery-status alarm combined with a rising load percentage would indicate the UPS is running on battery under load during a utility outage, warranting an escalation before battery depletion.

What Can Be Monitored

battery status/condition
input voltage
output voltage
load percentage
UPS alarm conditions

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
sysUpTime

OIDs

OID symbolic	OID numeric	Type	Access	Description
emerson	1.3.6.1.4.1.476
lcUpsAlarm	1.3.6.1.4.1.476.1.1.1.1.6
lcUpsAlarmAmbientOverTemp	1.3.6.1.4.1.476.1.1.1.1.6.3.29
lcUpsAlarmAutoRexferPrimed	1.3.6.1.4.1.476.1.1.1.1.6.3.43
lcUpsAlarmBattCycleBuffWarn	1.3.6.1.4.1.476.1.1.1.1.6.3.44
lcUpsAlarmBatteryBad	1.3.6.1.4.1.476.1.1.1.1.6.3.9
lcUpsAlarmBatteryCbOpen	1.3.6.1.4.1.476.1.1.1.1.6.3.37
lcUpsAlarmConditions	1.3.6.1.4.1.476.1.1.1.1.6.3
lcUpsAlarmControlPowerFailed	1.3.6.1.4.1.476.1.1.1.1.6.3.32
lcUpsAlarmDCgroundFault	1.3.6.1.4.1.476.1.1.1.1.6.3.34
lcUpsAlarmDCOverVoltageShutdown	1.3.6.1.4.1.476.1.1.1.1.6.3.18
OID lcUpsAlarmDescr	1.3.6.1.4.1.476.1.1.1.1.6.2.1.2	OBJECT IDENTIFIER	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.
lcUpsAlarmEmergencyPowerOff	1.3.6.1.4.1.476.1.1.1.1.6.3.30
lcUpsAlarmEmergencyXferToBypass	1.3.6.1.4.1.476.1.1.1.1.6.3.24
lcUpsAlarmEntry	1.3.6.1.4.1.476.1.1.1.1.6.2.1		not-accessible
lcUpsAlarmFanFailed	1.3.6.1.4.1.476.1.1.1.1.6.3.31
lcUpsAlarmFuseBlown	1.3.6.1.4.1.476.1.1.1.1.6.3.28
lcUpsAlarmHardwareShutdown	1.3.6.1.4.1.476.1.1.1.1.6.3.23
INT lcUpsAlarmId	1.3.6.1.4.1.476.1.1.1.1.6.2.1.1	INTEGER	read-only	A unique identifier for an alarm condition. This value must remain constant between agent initializations.
lcUpsAlarmInputCbOpen	1.3.6.1.4.1.476.1.1.1.1.6.3.38
lcUpsAlarmInputFreqError	1.3.6.1.4.1.476.1.1.1.1.6.3.13
lcUpsAlarmInputOverVoltage	1.3.6.1.4.1.476.1.1.1.1.6.3.8
lcUpsAlarmInverterFault	1.3.6.1.4.1.476.1.1.1.1.6.3.25
lcUpsAlarmLoadOnBypass	1.3.6.1.4.1.476.1.1.1.1.6.3.35
lcUpsAlarmLowBatteryShutdown	1.3.6.1.4.1.476.1.1.1.1.6.3.2
lcUpsAlarmLowBatteryWarning	1.3.6.1.4.1.476.1.1.1.1.6.3.1
lcUpsAlarmManualResetXfer	1.3.6.1.4.1.476.1.1.1.1.6.3.42
lcUpsAlarmModuleSummary	1.3.6.1.4.1.476.1.1.1.1.6.3.45
lcUpsAlarmOnBattery	1.3.6.1.4.1.476.1.1.1.1.6.3.10
lcUpsAlarmOutputCbOpen	1.3.6.1.4.1.476.1.1.1.1.6.3.39
lcUpsAlarmOutputFreqError	1.3.6.1.4.1.476.1.1.1.1.6.3.40
lcUpsAlarmOutputOverloadShutdown	1.3.6.1.4.1.476.1.1.1.1.6.3.7
lcUpsAlarmOutputOverloadWarning	1.3.6.1.4.1.476.1.1.1.1.6.3.6
lcUpsAlarmOutputOverVoltage	1.3.6.1.4.1.476.1.1.1.1.6.3.16
lcUpsAlarmOutputUnderVoltage	1.3.6.1.4.1.476.1.1.1.1.6.3.15
lcUpsAlarmOverTempShutdown	1.3.6.1.4.1.476.1.1.1.1.6.3.5
lcUpsAlarmOverTempWarning	1.3.6.1.4.1.476.1.1.1.1.6.3.4
lcUpsAlarmPhaseRotationError	1.3.6.1.4.1.476.1.1.1.1.6.3.26
lcUpsAlarmReversePower	1.3.6.1.4.1.476.1.1.1.1.6.3.33
GAU lcUpsAlarms	1.3.6.1.4.1.476.1.1.1.1.6.1	Gauge	read-only	The current number of alarm conditions.
lcUpsAlarmStaticSwUnable	1.3.6.1.4.1.476.1.1.1.1.6.3.41
lcUpsAlarmStopNoticeIssued	1.3.6.1.4.1.476.1.1.1.1.6.3.11
lcUpsAlarmTable	1.3.6.1.4.1.476.1.1.1.1.6.2		not-accessible
TIK lcUpsAlarmTime	1.3.6.1.4.1.476.1.1.1.1.6.2.1.3	TimeTicks	read-only	The value of sysUpTime when the alarm condition occured.
NTF lcUpsAlarmTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.11			An Alarm condition has occurred and is being reported in the lcUpsAlarmTable.
lcUpsAlarmUpsOff	1.3.6.1.4.1.476.1.1.1.1.6.3.12
lcUpsAlarmUtilFailed	1.3.6.1.4.1.476.1.1.1.1.6.3.3
lcUpsBadBypassPower	1.3.6.1.4.1.476.1.1.1.1.6.3.17
CTR lcUpsBatAmpHours	1.3.6.1.4.1.476.1.1.1.1.2.9	Counter	read-only	The number of amp hours withdrawn from battery.
INT lcUpsBatCapacity	1.3.6.1.4.1.476.1.1.1.1.2.6	INTEGER	read-only	The current battery capacity in percentage of total available.
INT lcUpsBatCurrent	1.3.6.1.4.1.476.1.1.1.1.2.4	INTEGER	read-only	The current battery discharging/charging current. (Unit of measure: Amp)
CTR lcUpsBatCycleDurationInSeconds	1.3.6.1.4.1.476.1.1.1.1.2.8	Counter	read-only	The total accumulated discharge time in seconds.
CTR lcUpsBatKWhours	1.3.6.1.4.1.476.1.1.1.1.2.10	Counter	read-only	The number of Kilowatt-hours withdrawn from battery.
INT lcUpsBatTemperature	1.3.6.1.4.1.476.1.1.1.1.2.2	INTEGER	read-only	The battery temperature. (Unit of measure: Degree, Centigrade)
lcUpsBattery	1.3.6.1.4.1.476.1.1.1.1.2
INT lcUpsBatTimeRemaining	1.3.6.1.4.1.476.1.1.1.1.2.1	INTEGER	read-only	The estimated time to depletion of battery charge. (Unit of measure: Minute)
CTR lcUpsBatTotalDischCounts	1.3.6.1.4.1.476.1.1.1.1.2.7	Counter	read-only	The number of discharges the UPS has experienced.
INT lcUpsBatVoltage	1.3.6.1.4.1.476.1.1.1.1.2.3	INTEGER	read-only	The current battery voltage. (Unit of measure: volt)
CTR lcUpsBatWattHours	1.3.6.1.4.1.476.1.1.1.1.2.11	Counter	read-only	The number of Watt-hours withdrawn from battery.
lcUpsBypass	1.3.6.1.4.1.476.1.1.1.1.13
INT lcUpsBypassCurrent	1.3.6.1.4.1.476.1.1.1.1.13.4.1.3	INTEGER	read-only	The bypass current. (Unit of measure: Amp)
lcUpsBypassEntry	1.3.6.1.4.1.476.1.1.1.1.13.4.1		not-accessible
INT lcUpsBypassFrequency	1.3.6.1.4.1.476.1.1.1.1.13.2	INTEGER	read-only	The current bypass frequency. (Unit of measure: Hertz)
INT lcUpsBypassLine	1.3.6.1.4.1.476.1.1.1.1.13.4.1.1	INTEGER	read-only	The bypass Line.
INT lcUpsBypassNumLines	1.3.6.1.4.1.476.1.1.1.1.13.3	INTEGER	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.
lcUpsBypassTable	1.3.6.1.4.1.476.1.1.1.1.13.4		not-accessible
INT lcUpsBypassVoltage	1.3.6.1.4.1.476.1.1.1.1.13.4.1.2	INTEGER	read-only	The bypass voltage. (Unit of measure: Volt)
lcUpsConfig	1.3.6.1.4.1.476.1.1.1.1.14
INT lcUpsConfigAudibleStatus	1.3.6.1.4.1.476.1.1.1.1.14.5	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm.
INT lcUpsConfigAutoRestart	1.3.6.1.4.1.476.1.1.1.1.14.7	INTEGER	read-write	Setting this object will start the output after the indicated number of ticks (1 tick = 10 seconds), including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will disable autorestart.
INT lcUpsConfigBypassInstalled	1.3.6.1.4.1.476.1.1.1.1.14.2	INTEGER	read-only	Indicates if a bypass is installed in the UPS.
INT lcUpsConfigCurrentModule	1.3.6.1.4.1.476.1.1.1.1.14.4	INTEGER	read-write	A number identifying which module of a multi-module UPS is currently being monitored.
INT lcUpsConfigLowBattTime	1.3.6.1.4.1.476.1.1.1.1.14.6	INTEGER	read-write	The value of lcUpsBatTimeRemaining at which a lowBatteryWarning condition is declared. (Unit of measure: Minute)
INT lcUpsConfigModuleCount	1.3.6.1.4.1.476.1.1.1.1.14.3	INTEGER	read-only	A number identifying how many multi-module UPS are connected to the System Control Cabinet.
INT lcUpsConfigType	1.3.6.1.4.1.476.1.1.1.1.14.1	INTEGER	read-only	Indicates the UPS topology.
lcUpsControl	1.3.6.1.4.1.476.1.1.1.1.8
INT lcUpsControlCancelCommands	1.3.6.1.4.1.476.1.1.1.1.8.7	INTEGER	read-write	Setting this variable to 'cancel' will cause the agent to issue instructions to the UPS to cancel all outstanding commands, such as lcUpsControlOutputOff, lcUpsControlOutputOn, lcUpsControlUnixShutdown.
INT lcUpsControlOutputOffDelay	1.3.6.1.4.1.476.1.1.1.1.8.1	INTEGER	read-write	Setting this object causes the agent to instruct the UPS to turn off the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOffTrap when the countdown finishes. Note that different models have different clock resolutions, usually greater than 1 second. As a result, the command will only be accurate to the resolution of the UPS's clock. The command can be cancelled by setting lcUpsControlCancelCommand to the value cancel.
INT lcUpsControlOutputOffTrapDelay	1.3.6.1.4.1.476.1.1.1.1.8.3	INTEGER	read-write	When 'lcUpsControlOutputOffDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOffWarningTrap will be produced and this object will be reset to 0.
INT lcUpsControlOutputOnDelay	1.3.6.1.4.1.476.1.1.1.1.8.2	INTEGER	read-write	Setting this object causes the agent to instruct the UPS to turn on the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOnTrap when the countdown finishes. Note that different models have different clock resolutions, usually greater than 1 second. As a result, the command will only be accurate to the resolution of the UPS's clock. The command can be cancelled by setting lcUpsControlCancelCommand to the value cancel.
INT lcUpsControlOutputOnTrapDelay	1.3.6.1.4.1.476.1.1.1.1.8.4	INTEGER	read-write	When 'lcUpsControlOutputOnDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOnWarningTrap will be produced and this object will be reset to 0.
NTF lcUpsControlPowerFailureTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.27			An lcUpsControlPowerFailureTrap signifies a failure in the secondary control power.
INT lcUpsControlRebootAgentDelay	1.3.6.1.4.1.476.1.1.1.1.8.8	INTEGER	read-write	Setting this object causes the agent to reboot after the indicated number of seconds have expired. The value will count down until the event takes place.
INT lcUpsControlUnixShutdownDelay	1.3.6.1.4.1.476.1.1.1.1.8.5	INTEGER	read-write	Setting this object causes the agent to instruct the UPS to perform a UNIX Shutdown in the indicated number of seconds. The agent counts down the number of seconds until the event will take place. A Unix shutdown is only valid if the UPS is on Battery. During a UNIX Shutdown, the UPS will turn off the output even if the Utility comes back on line before the shutdown time arrives. Note that different models have different clock resolutions, usually greater than 1 second. As a result, the command will only be accurate to the resolution of the UPS's clock. The command can be cancelled by setting lcUpsControlCancelCommand to the value 'cancel'.
INT lcUpsControlUnixShutdownTrapDelay	1.3.6.1.4.1.476.1.1.1.1.8.6	INTEGER	read-write	When 'lcUpsControlUnixShutdownDelay' reaches a value less than or equal to this object's value, an lcUpsUnixShutdownWarningTrap will be produced and this object will be reset to 0.
NTF lcUpsDCOverVoltageShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.23			An lcUpsDCOverVoltageShutdownTrap signifies that the UPS has detected that battery voltage is over the tolarable level.
NTF lcUpsEmergencyPowerOffTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.26			An lcUpsEmergencyPowerOffTrap signifies that the UPS has shut off output due to an emergency condition.
NTF lcUpsEmergencyXferToBypassTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.31			An lcUpsEmergencyXferToBypassTrap signifies that the UPS has automatically tranferred the load to bypass power.
NTF lcUpsFuseBlownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.25			An lcUpsFuseBlownTrap is sent when the UPS's rectifier or DC capacitor fuse has failed.
lcUpsIdent	1.3.6.1.4.1.476.1.1.1.1.1
STR lcUpsIdentFirmwareVersion	1.3.6.1.4.1.476.1.1.1.1.1.5	DisplayString	read-only	The firmware revision level of the UPS.
STR lcUpsIdentManufactureDate	1.3.6.1.4.1.476.1.1.1.1.1.7	DisplayString	read-only	The date of manufacture of the UPS.
STR lcUpsIdentManufacturer	1.3.6.1.4.1.476.1.1.1.1.1.1	DisplayString	read-only	The UPS manufacturer.
STR lcUpsIdentModel	1.3.6.1.4.1.476.1.1.1.1.1.2	DisplayString	read-write	The UPS Model designation.
STR lcUpsIdentSerialNumber	1.3.6.1.4.1.476.1.1.1.1.1.6	DisplayString	read-only	The serial number of the UPS.
STR lcUpsIdentSoftwareVersion	1.3.6.1.4.1.476.1.1.1.1.1.3	DisplayString	read-only	The UPS SNMP Agent software version.
OID lcUpsIdentSpecific	1.3.6.1.4.1.476.1.1.1.1.1.4	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular UPS being managed. This object is used to locate the product-specific MIB for this device. If this information is not present, its value should be the OBJECT IDENTIFIER { 0 0 }, which is a syntactically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
lcUpsInput	1.3.6.1.4.1.476.1.1.1.1.3
CTR lcUpsInputBlackOuts	1.3.6.1.4.1.476.1.1.1.1.3.3	Counter	read-only	The number of black-out conditions the UPS has experienced.
CTR lcUpsInputBrownOuts	1.3.6.1.4.1.476.1.1.1.1.3.2	Counter	read-only	The number of brown-out conditions the UPS has experienced.
INT lcUpsInputCurrent	1.3.6.1.4.1.476.1.1.1.1.3.6.1.3	INTEGER	read-only	The input current. (Unit of measure: Amp)
lcUpsInputEntry	1.3.6.1.4.1.476.1.1.1.1.3.6.1		not-accessible
NTF lcUpsInputFreqErrorTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.22			An ldUpsInputFreqErrorTrap signifies that the UPS has detected that input frequency is outside tolerable variance.
INT lcUpsInputFrequency	1.3.6.1.4.1.476.1.1.1.1.3.1	INTEGER	read-only	The current input frequency. (Unit of measure: Hertz)
INT lcUpsInputLine	1.3.6.1.4.1.476.1.1.1.1.3.6.1.1	INTEGER	read-only	The input Line.
INT lcUpsInputNumLines	1.3.6.1.4.1.476.1.1.1.1.3.5	INTEGER	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
NTF lcUpsInputOverVoltageTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.8			An lcUpsInputOverVoltageTrap signifies that the UPS has detected a high input voltage condition.
lcUpsInputTable	1.3.6.1.4.1.476.1.1.1.1.3.6		not-accessible
CTR lcUpsInputTransients	1.3.6.1.4.1.476.1.1.1.1.3.4	Counter	read-only	The number of transient (surge and spike) conditions the UPS has experienced.
INT lcUpsInputVA	1.3.6.1.4.1.476.1.1.1.1.3.6.1.4	INTEGER	read-only	The input volt-amps.
INT lcUpsInputVoltage	1.3.6.1.4.1.476.1.1.1.1.3.6.1.2	INTEGER	read-only	The input voltage. (Unit of measure: Volt)
lcUpsInverter	1.3.6.1.4.1.476.1.1.1.1.5
NTF lcUpsInverterFaultTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.34			An lcUpsInverterFaultTrap signifies that the UPS detected a problem with the Inverter.
INT lcUpsInverterStatus	1.3.6.1.4.1.476.1.1.1.1.5.1	INTEGER	read-only	The state of the inverter. Unknown is returned if the state can not be determined.
INT lcUpsInverterTemp	1.3.6.1.4.1.476.1.1.1.1.5.2	INTEGER	read-only	The temperature of the inverter. (Unit of measure: degree, Centigrade)
lcUpsLineCorrectionActive	1.3.6.1.4.1.476.1.1.1.1.6.3.46
NTF lcUpsLoadOnBypassTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.30			An lcUpsLoadOnBypassTrap signifies that the load has been transferred to bypass power.
NTF lcUpsLowBatteryShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.5			An lcUpsLowBatteryShutdownTrap signifies that the UPS has shut off the output due to a Low Battery state.
NTF lcUpsLowBatteryWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.4			An lcUpsLowBatteryWarningTrap signifies that the UPS has entered a Low Battery state.
lcUpsNominal	1.3.6.1.4.1.476.1.1.1.1.9
INT lcUpsNominalInputFreq	1.3.6.1.4.1.476.1.1.1.1.9.6	INTEGER	read-write	The nominal input frequency. (Unit of measure: Hertz)
INT lcUpsNominalInputVoltage	1.3.6.1.4.1.476.1.1.1.1.9.2	INTEGER	read-write	The nominal input voltage. (Unit of measure: volt)
INT lcUpsNominalOutputFreq	1.3.6.1.4.1.476.1.1.1.1.9.5	INTEGER	read-write	The nominal output frequency. (Unit of measure: Hertz)
INT lcUpsNominalOutputVA	1.3.6.1.4.1.476.1.1.1.1.9.3	INTEGER	read-write	The nominal Volt-Amp rating.
INT lcUpsNominalOutputVaRating	1.3.6.1.4.1.476.1.1.1.1.9.7	INTEGER	read-write	The nominal Volt-Amp rating.
INT lcUpsNominalOutputVoltage	1.3.6.1.4.1.476.1.1.1.1.9.1	INTEGER	read-write	The nominal output voltage. (Unit of measure: volt)
INT lcUpsNominalOutputWatts	1.3.6.1.4.1.476.1.1.1.1.9.4	INTEGER	read-write	The nominal power rating. (Unit of measure: watt)
INT lcUpsNominalOutputWattsRating	1.3.6.1.4.1.476.1.1.1.1.9.8	INTEGER	read-write	The nominal power rating. (Unit of measure: watt)
NTF lcUpsOnBatteryTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.3			An lcUpsOnBatteryTrap signifies that the UPS is currently on Battery Power.
INT lcUpsOnBypass	1.3.6.1.4.1.476.1.1.1.1.13.1	INTEGER	read-only	Indicates that the UPS is currently on bypass.
lcUpsOutput	1.3.6.1.4.1.476.1.1.1.1.4
INT lcUpsOutputCurrent	1.3.6.1.4.1.476.1.1.1.1.4.4.1.3	INTEGER	read-only	The output current. (Unit of measure: Amp)
lcUpsOutputEntry	1.3.6.1.4.1.476.1.1.1.1.4.4.1		not-accessible
INT lcUpsOutputFrequency	1.3.6.1.4.1.476.1.1.1.1.4.1	INTEGER	read-only	The current output frequency. (Unit of measure: Hertz)
INT lcUpsOutputLine	1.3.6.1.4.1.476.1.1.1.1.4.4.1.1	INTEGER	read-only	The output Line.
INT lcUpsOutputLoad	1.3.6.1.4.1.476.1.1.1.1.4.2	INTEGER	read-only	The current output load percentage.
INT lcUpsOutputNumLines	1.3.6.1.4.1.476.1.1.1.1.4.3	INTEGER	read-only	The number of output lines utilized in this device. This entry indicates the number of rows in the output table.
NTF lcUpsOutputOffTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.12			An lcUpsOutputOffTrap is sent when the UPS turns all of its output off, either at the inverter or via a relay.
NTF lcUpsOutputOffWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.13			An lcUpsOutputOffWarningTrap is sent when the lcUpsControlOutputOffDelay reaches the value of lcUpsControlOutputOffTrapDelay.
NTF lcUpsOutputOnTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.14			An lcUpsOutputOnTrap is sent when the UPS turns all of its output back on, either at the inverter or via a relay.
NTF lcUpsOutputOnWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.15			An lcUpsOutputOnWarningTrap is sent when the lcUpsControlOutputOnDelay reaches the value of lcUpsControlOutputOnTrapDelay.
NTF lcUpsOutputOverVoltageTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.24			An lcUpsOutputOverVoltageTrap signifies that the UPS has detected that the output voltage is too high.
lcUpsOutputTable	1.3.6.1.4.1.476.1.1.1.1.4.4		not-accessible
INT lcUpsOutputVA	1.3.6.1.4.1.476.1.1.1.1.4.4.1.4	INTEGER	read-only	The output volt-amps.
INT lcUpsOutputVoltage	1.3.6.1.4.1.476.1.1.1.1.4.4.1.2	INTEGER	read-only	The output voltage. (Unit of measure: Volt)
INT lcUpsOutputWatts	1.3.6.1.4.1.476.1.1.1.1.4.5	INTEGER	read-only	The output power in watts.
NTF lcUpsOverloadShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.2			An lcUpsOverloadShutdownTrap signifies that the UPS has detected an Overload condition where the output load has exceeded the UPS's rated capacity and has shut off the output.
NTF lcUpsOverloadWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.1			An lcUpsOverloadWarningTrap signifies that the UPS has detected an Overload condition where the output load has exceeded the UPS's rated capacity.
NTF lcUpsOverTempShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.10			An lcUpsOverTempShutdownTrap signifies that the UPS has detected a excessive temperature condition and shut off the output.
NTF lcUpsOverTempWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.9			An lcUpsOverTempWarningTrap signifies that the UPS has detected a excessive temperature condition.
NTF lcUpsPhaseRotationErrorTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.29			An lcUpsPhaseRotationErrorTrap signifies a phase-rotation error in the bypass power.
NTF lcUpsReceptOffTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.18			An lcUpsReceptOffTrap is sent when the UPS turns an output receptacle off.
NTF lcUpsReceptOffWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.19			An lcUpsReceptOffWarningTrap is sent when the lcUpsSwitchedReceptOffDelay reaches the value of lcUpsSwitchedReceptOffTrapDelay.
NTF lcUpsReceptOnTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.20			An lcUpsReceptOnTrap is sent when the UPS turns an output receptacle on.
NTF lcUpsReceptOnWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.21			An lcUpsReceptOnWarningTrap is sent when the lcUpsSwitchedReceptOnDelay reaches the value of lcUpsSwitchedReceptOnTrapDelay.
NTF lcUpsReversePowerTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.28			An lcUpsReversePowerTrap signifies that output has been shut off due to a reverse power flow condition.
lcUpsSwitchedReceptacles	1.3.6.1.4.1.476.1.1.1.1.12
lcUpsSwitchedReceptEntry	1.3.6.1.4.1.476.1.1.1.1.12.2.1		not-accessible
INT lcUpsSwitchedReceptIndex	1.3.6.1.4.1.476.1.1.1.1.12.2.1.1	INTEGER	read-only
STR lcUpsSwitchedReceptLabel	1.3.6.1.4.1.476.1.1.1.1.12.2.1.7	DisplayString	read-write	A user-defined text string associated with a switched receptacle. This may be used to describe the load powered from the receptacle. The text string is stored in non-volatile memory.
INT lcUpsSwitchedReceptMaxNum	1.3.6.1.4.1.476.1.1.1.1.12.1	INTEGER	read-only	The maximum number of switched receptacles supported by the Ups.
INT lcUpsSwitchedReceptOffDelay	1.3.6.1.4.1.476.1.1.1.1.12.2.1.4	INTEGER	read-write	Setting this object causes the agent to instruct the UPS to turn off a receptacle after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsReceptOffTrap when the countdown finishes. Note that different models have different clock resolutions, usually greater than 1 second. As a result, the command will only be accurate to the resolution of the UPS's clock. The command can be cancelled by setting lcUpsSwitchedCancelCommand to the value cancel.
INT lcUpsSwitchedReceptOffTrapDelay	1.3.6.1.4.1.476.1.1.1.1.12.2.1.5	INTEGER	read-write	When 'lcUpsSwitchedReceptOffDelay' reaches a value less than or equal to this object's value, an lcUpsReceptOffWarningTrap will be produced and this object will be reset to 0.
INT lcUpsSwitchedReceptOnDelay	1.3.6.1.4.1.476.1.1.1.1.12.2.1.2	INTEGER	read-write	Setting this object causes the agent to instruct the UPS to turn on a receptacle after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsReceptOnTrap when the countdown finishes. Note that different models have different clock resolutions, usually greater than 1 second. As a result, the command will only be accurate to the resolution of the UPS's clock. The command can be cancelled by setting lcUpsSwitchedCancelCommand to the value cancel.
INT lcUpsSwitchedReceptOnTrapDelay	1.3.6.1.4.1.476.1.1.1.1.12.2.1.3	INTEGER	read-write	When 'lcUpsSwitchedReceptOnDelay' reaches a value less than or equal to this object's value, an lcUpsReceptOnWarningTrap will be produced and this object will be reset to 0.
INT lcUpsSwitchedReceptStatus	1.3.6.1.4.1.476.1.1.1.1.12.2.1.6	INTEGER	read-only	The status of the device receptacle. Note that some devices may support Switched of device receptacles as a group only (by using lcUpsSwitchedOutputOffDelay and lcUpsSwitchedOutputOnDelay).
lcUpsSwitchedReceptTable	1.3.6.1.4.1.476.1.1.1.1.12.2		not-accessible
lcUpsTest	1.3.6.1.4.1.476.1.1.1.1.7
INT lcUpsTestBattery	1.3.6.1.4.1.476.1.1.1.1.7.1	INTEGER	read-write	Setting this variable to 'start' will initiate the battery test. Setting this variable to 'abort' will stop the battery test if the test is in- progress, otherwise it has no effect. Setting this variable to 'unknown' has no effect. Reading this variable will always result in a return value of 'unknown'. If 'lcUpsTestBatteryStatus' is 'failed' the test may not be performed again and the status will remain in the failure state.
INT lcUpsTestBatteryStatus	1.3.6.1.4.1.476.1.1.1.1.7.2	INTEGER	read-only	The status of the battery test.
INT lcUpsTestDiag	1.3.6.1.4.1.476.1.1.1.1.7.3	INTEGER	read-write	Setting this variable to 'start' will initiate the diagnostics test. Setting this variable to 'abort' will stop the diagnostics test if the test is in-progress, otherwise it has no effect. Setting this variable to 'unknown' has no effect. Reading this variable will always result in a return value of 'unknown'.
INT lcUpsTestDiagStatus	1.3.6.1.4.1.476.1.1.1.1.7.4	INTEGER	read-only	The status of the diagnostics test.
lcUpsTraps	1.3.6.1.4.1.476.1.1.1.1.11
NTF lcUpsUnixShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.16			An lcUpsUnixShutodwnTrap is sent 2 seconds before the UPS is scheduled to perform a Unix Shutdown.
NTF lcUpsUnixShutdownWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.17			An lcUpsUnixShutdownWarningTrap is sent when the lcUpsControlUnixShudownDelay reaches the value of lcUpsControlUnixShutdownTrapDelay.
NTF lcUpsUtilPowerFailedTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.6			An lcUpsUtilPowerFailedTrap signifies that the utility power input to the UPS has been lost.
NTF lcUpsUtilPowerRestoredTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.7			An lcUpsUtilPowerRestoredTrap signifies that the utility power has been restored to the UPS.
ldUpsAlarm	1.3.6.1.4.1.476.1.1.1.3.6
ldUpsAlarmBoostOn	1.3.6.1.4.1.476.1.1.1.3.6.1.6
ldUpsAlarmChargerFailed	1.3.6.1.4.1.476.1.1.1.3.6.1.10
ldUpsAlarmConditions	1.3.6.1.4.1.476.1.1.1.3.6.1
ldUpsAlarmDCOverVoltageShutdown	1.3.6.1.4.1.476.1.1.1.3.6.1.1
ldUpsAlarmImminentShutdown	1.3.6.1.4.1.476.1.1.1.3.6.1.4
ldUpsAlarmInputFreqError	1.3.6.1.4.1.476.1.1.1.3.6.1.5
ldUpsAlarmLNReversedShutdown	1.3.6.1.4.1.476.1.1.1.3.6.1.3
ldUpsAlarmOutputOverVoltage	1.3.6.1.4.1.476.1.1.1.3.6.1.8
ldUpsAlarmOutputShortShutdown	1.3.6.1.4.1.476.1.1.1.3.6.1.2
ldUpsAlarmOutputUnderVoltage	1.3.6.1.4.1.476.1.1.1.3.6.1.9
ldUpsAlarmReplaceBattery	1.3.6.1.4.1.476.1.1.1.3.6.1.7
NTF ldUpsChargerFailedTrap	1.3.6.1.4.1.476.1.1.1.3.11.0.8			An ldUpsChargerFailedTrap signifies that the UPS has detected that the battery charger has failed.
NTF ldUpsDCOverVoltageShutdownTrap	1.3.6.1.4.1.476.1.1.1.3.11.0.1			An ldUpsDCOverVoltageShutdownTrap signifies that the UPS has detected that battery voltage is over the tolarable level.
NTF ldUpsImminentShutdownTrap	1.3.6.1.4.1.476.1.1.1.3.11.0.4			An ldUpsImminentShutdownTrap signifies that the UPS is about to turn off output power.
ldUpsInput	1.3.6.1.4.1.476.1.1.1.3.3
NTF ldUpsInputFreqErrorTrap	1.3.6.1.4.1.476.1.1.1.3.11.0.5			An ldUpsInputFreqErrorTrap signifies that the UPS has detected that input frequency is outside tolerable variance.
INT ldUpsInputMaxVoltsSinceLastPoll	1.3.6.1.4.1.476.1.1.1.3.3.1	INTEGER	read-only	The maximum input voltage encountered since the object was last retrieved. Note: if there are multiple managers talking to the same agent, the use of this object needs to be coordinated.
INT ldUpsInputMinVoltsSinceLastPoll	1.3.6.1.4.1.476.1.1.1.3.3.2	INTEGER	read-only	The minimum input voltage encountered since the object was last retrieved. Note: if there are multiple managers talking to the same agent, the use of this object needs to be coordinated.
NTF ldUpsLNReversedShutdownTrap	1.3.6.1.4.1.476.1.1.1.3.11.0.3			An ldUpsLNReversedShutdownTrap signifies that the UPS has detected that Line and Neutral have been reversed.
ldUpsOutput	1.3.6.1.4.1.476.1.1.1.3.4
INT ldUpsOutputMaxVoltsSinceLastPoll	1.3.6.1.4.1.476.1.1.1.3.4.1	INTEGER	read-only	The maximum output voltage encountered since the object was last retrieved. Note: if there are multiple managers talking to the same agent, the use of this object needs to be coordinated.
INT ldUpsOutputMinVoltsSinceLastPoll	1.3.6.1.4.1.476.1.1.1.3.4.2	INTEGER	read-only	The minimum output voltage encountered since the object was last retrieved. Note: if there are multiple managers talking to the same agent, the use of this object needs to be coordinated.
NTF ldUpsOutputOverVoltageTrap	1.3.6.1.4.1.476.1.1.1.3.11.0.6			An ldUpsOutputOverVoltageTrap signifies that the UPS has detected that the output voltage is too high.
NTF ldUpsOutputShortShutdownTrap	1.3.6.1.4.1.476.1.1.1.3.11.0.2			An ldUpsOutputShortShutdownTrap signifies that the UPS has detected a short circuit across the output.
NTF ldUpsOutputUnderVoltageTrap	1.3.6.1.4.1.476.1.1.1.3.11.0.7			An ldUpsOutputUnderVoltageTrap signifies that the UPS has detected that the output voltage is too low.
ldUpsTraps	1.3.6.1.4.1.476.1.1.1.3.11
lgUpsAlarm	1.3.6.1.4.1.476.1.1.1.4.6
lgUpsAlarmConditions	1.3.6.1.4.1.476.1.1.1.4.6.1
lgUpsAlarmDCOverVoltageShutdown	1.3.6.1.4.1.476.1.1.1.4.6.1.1
lgUpsAlarmInputUVOnStartup	1.3.6.1.4.1.476.1.1.1.4.6.1.5
lgUpsAlarmLNReversedShutdown	1.3.6.1.4.1.476.1.1.1.4.6.1.3
lgUpsAlarmOutputShortShutdown	1.3.6.1.4.1.476.1.1.1.4.6.1.2
lgUpsAlarmPFCFailedOnStartup	1.3.6.1.4.1.476.1.1.1.4.6.1.6
lgUpsAlarmRemoteShutdown	1.3.6.1.4.1.476.1.1.1.4.6.1.4
NTF lgUpsDCOverVoltageShutdownTrap	1.3.6.1.4.1.476.1.1.1.4.11.0.1			An lgUpsDCOverVoltageShutdownTrap signifies that the UPS has detected that battery voltage is over the nominal level.
NTF lgUpsInputUVOnStartupTrap	1.3.6.1.4.1.476.1.1.1.4.11.0.4			An lgUpsInputUVOnStartupTrap signifies that the UPS detected a low voltage condition upon system startup.
NTF lgUpsLNReversedShutdownTrap	1.3.6.1.4.1.476.1.1.1.4.11.0.3			An lgUpsLNReversedShutdownTrap signifies that the UPS has detected that Line and Neutral have been reversed.
NTF lgUpsOutputShortShutdownTrap	1.3.6.1.4.1.476.1.1.1.4.11.0.2			An lgUpsOutputShortShutdownTrap signifies that the UPS has detected a short circuit across the output.
lgUpsTraps	1.3.6.1.4.1.476.1.1.1.4.11
liebertCorp	1.3.6.1.4.1.476.1
liebertUps	1.3.6.1.4.1.476.1.1
ls43cUpsBypass	1.3.6.1.4.1.476.1.1.1.10.13
INT ls43cUpsBypassCurrent	1.3.6.1.4.1.476.1.1.1.10.13.4.1.3	INTEGER	read-only	The bypass current. (Unit of measure: Amp)
ls43cUpsBypassEntry	1.3.6.1.4.1.476.1.1.1.10.13.4.1		not-accessible
INT ls43cUpsBypassFrequency	1.3.6.1.4.1.476.1.1.1.10.13.2	INTEGER	read-only	The current bypass frequency. (Unit of measure: Hertz)
INT ls43cUpsBypassLine	1.3.6.1.4.1.476.1.1.1.10.13.4.1.1	INTEGER	read-only	The bypass Line.
INT ls43cUpsBypassNumLines	1.3.6.1.4.1.476.1.1.1.10.13.3	INTEGER	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.
ls43cUpsBypassTable	1.3.6.1.4.1.476.1.1.1.10.13.4		not-accessible
INT ls43cUpsBypassVoltage	1.3.6.1.4.1.476.1.1.1.10.13.4.1.2	INTEGER	read-only	The bypass voltage. (Unit of measure: Volt)
ls43cUpsConfig	1.3.6.1.4.1.476.1.1.1.10.12
INT ls43cUpsConfigBypassInstalled	1.3.6.1.4.1.476.1.1.1.10.12.1	INTEGER	read-only	Indicates if a bypass is installed in the UPS.
ls43cUpsIdent	1.3.6.1.4.1.476.1.1.1.10.1
STR ls43cUpsIdentFirmwareVersion	1.3.6.1.4.1.476.1.1.1.10.1.1	DisplayString	read-only	The firmware revision level of the UPS.
INT ls43cUpsOnBypass	1.3.6.1.4.1.476.1.1.1.10.13.1	INTEGER	read-only	Indicates that the UPS is currently on bypass.
lsUpsAlarm	1.3.6.1.4.1.476.1.1.1.2.6
lsUpsAlarmCheckAirFilter	1.3.6.1.4.1.476.1.1.1.2.6.1.1
lsUpsAlarmConditions	1.3.6.1.4.1.476.1.1.1.2.6.1
lsUpsBypass	1.3.6.1.4.1.476.1.1.1.2.13
INT lsUpsBypassCurrent	1.3.6.1.4.1.476.1.1.1.2.13.4.1.3	INTEGER	read-only	The bypass current. (Unit of measure: Amp)
lsUpsBypassEntry	1.3.6.1.4.1.476.1.1.1.2.13.4.1		not-accessible
INT lsUpsBypassFrequency	1.3.6.1.4.1.476.1.1.1.2.13.2	INTEGER	read-only	The current bypass frequency. (Unit of measure: Hertz)
INT lsUpsBypassLine	1.3.6.1.4.1.476.1.1.1.2.13.4.1.1	INTEGER	read-only	The bypass Line.
INT lsUpsBypassNumLines	1.3.6.1.4.1.476.1.1.1.2.13.3	INTEGER	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.
lsUpsBypassTable	1.3.6.1.4.1.476.1.1.1.2.13.4		not-accessible
INT lsUpsBypassVoltage	1.3.6.1.4.1.476.1.1.1.2.13.4.1.2	INTEGER	read-only	The bypass voltage. (Unit of measure: Volt)
NTF lsUpsCheckAirFilterTrap	1.3.6.1.4.1.476.1.1.1.2.11.0.1			An lsUpsCheckAirFilterTrap signifies that the programmed time interval for checking the air filter has passed and it is time to check the air filter.
lsUpsConfig	1.3.6.1.4.1.476.1.1.1.2.12
INT lsUpsConfigBypassInstalled	1.3.6.1.4.1.476.1.1.1.2.12.1	INTEGER	read-only	Indicates if a bypass is installed in the UPS.
lsUpsIdent	1.3.6.1.4.1.476.1.1.1.2.1
STR lsUpsIdentFirmwareVersion	1.3.6.1.4.1.476.1.1.1.2.1.1	DisplayString	read-only	The firmware revision level of the UPS.
INT lsUpsOnBypass	1.3.6.1.4.1.476.1.1.1.2.13.1	INTEGER	read-only	Indicates that the UPS is currently on bypass.
lsUpsTraps	1.3.6.1.4.1.476.1.1.1.2.11
luCore	1.3.6.1.4.1.476.1.1.1.1
luExperimental	1.3.6.1.4.1.476.1.1.2
luExtensions	1.3.6.1.4.1.476.1.1.1
luExternal	1.3.6.1.4.1.476.1.1.1.6
luPowerSure	1.3.6.1.4.1.476.1.1.1.15
luPrivate	1.3.6.1.4.1.476.1.1.3
luSeries200	1.3.6.1.4.1.476.1.1.1.8
luSeries200Alarm	1.3.6.1.4.1.476.1.1.1.8.6
luSeries200AlarmConditions	1.3.6.1.4.1.476.1.1.1.8.6.1
luSeries200AlarmInputFreqError	1.3.6.1.4.1.476.1.1.1.8.6.1.1
luSeries200Bypass	1.3.6.1.4.1.476.1.1.1.8.13
luSeries200Config	1.3.6.1.4.1.476.1.1.1.8.12
INT luSeries200ConfigBypassInstalled	1.3.6.1.4.1.476.1.1.1.8.12.1	INTEGER	read-only	Indicates if a bypass is installed in the UPS.
INT luSeries200ConfigFrequencyChangerModel	1.3.6.1.4.1.476.1.1.1.8.12.2	INTEGER	read-only	Indicates whether this AP200 model is a frequency changer model.
luSeries200Input	1.3.6.1.4.1.476.1.1.1.8.3
INT luSeries200InputMaxVoltsSinceLastPoll	1.3.6.1.4.1.476.1.1.1.8.3.1	INTEGER	read-only	The maximum input voltage encountered since the object was last retrieved. Note: if there are multiple managers talking to the same agent, the use of this object needs to be coordinated.
INT luSeries200InputMinVoltsSinceLastPoll	1.3.6.1.4.1.476.1.1.1.8.3.2	INTEGER	read-only	The minimum input voltage encountered since the object was last retrieved. Note: if there are multiple managers talking to the same agent, the use of this object needs to be coordinated.
INT luSeries200OnBypass	1.3.6.1.4.1.476.1.1.1.8.13.1	INTEGER	read-only	Indicates that the UPS is currently on bypass.
luSeries300	1.3.6.1.4.1.476.1.1.1.5
luSeries4300	1.3.6.1.4.1.476.1.1.1.10
luSystemCabinet	1.3.6.1.4.1.476.1.1.1.12
luUpsModule	1.3.6.1.4.1.476.1.1.1.11
luUPStationD	1.3.6.1.4.1.476.1.1.1.3
luUPStationG	1.3.6.1.4.1.476.1.1.1.4
luUPStationGxt	1.3.6.1.4.1.476.1.1.1.14
luUPStationS	1.3.6.1.4.1.476.1.1.1.2
luUPStationS3	1.3.6.1.4.1.476.1.1.1.7

RFC description

Manages Liebert UPS systems, providing monitoring and configuration of uninterruptible power supply devices and parameters.

Start monitoring Liebert (Vertiv) UPS unit with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download LIEBERT-UPS-MIB

What Is LIEBERT-UPS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description