All MIBs › LX-10-MIB
Category: Domain: WAN
Description: SNMP management MIB for the LX-10 series terminal server or console server, providing port, session, and access management objects.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is LX-10-MIB?
This is a vendor MIB for the LX-10 series terminal/console server, a device used to provide serial console and out-of-band access to networked equipment. Although no object list was captured for this module in the source, MIBs of this class typically expose port status, active session information, and access-control configuration for each serial line the unit manages. Their monitoring value centers on hardware/software status such as whether each serial port is up and in use, how many sessions are active, and whether authentication or access restrictions are correctly enforced. Terminal server MIBs of this kind are generally self-contained but may reference standard interface (IF-MIB) conventions for port indexing. They are deployed in data centers and network operations environments where administrators need remote, low-level console access to routers, switches, and servers even when primary network paths are down, and can download the LX-10-MIB file to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in LX-10-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- terminal/console server
- out-of-band management appliance
Monitoring Examples
A network operations team would typically poll per-port status objects to confirm which serial console ports are actively connected to managed devices and which are idle or faulted. Session-count and session-table objects would be used to see how many engineers are currently connected via the console server, helping detect stale or abandoned sessions. Port configuration objects (baud rate, access mode) would be checked after a change to confirm the console line matches the attached equipment's serial settings.
What Can Be Monitored
- serial port status
- active console sessions
- port configuration/baud settings
- access control state
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF alarmOffReport | 1.3.6.1.4.1.135.22.0.2 | LX-10-specific trap sent by the managed node when an alarm condition is cleared. | ||
| NTF alarmOnReport | 1.3.6.1.4.1.135.22.0.1 | LX-10-specific trap sent by the managed node when an alarm condition is set. | ||
| config | 1.3.6.1.4.1.135.22.2 | |||
| configAfa | 1.3.6.1.4.1.135.22.2.3 | |||
| INT configAfaActivationRate | 1.3.6.1.4.1.135.22.2.3.1 | INTEGER | read-write | AFA activation rate is used by the managed node to decide when it will disable the operational status of a T1 interface if the interface's BER rate is above the selected activation rate for a period specified by configAfaActivationTime (see below). |
| INT configAfaActivationTime | 1.3.6.1.4.1.135.22.2.3.2 | INTEGER | read-write | See above description. Unit - minute |
| INT configAfaDeactivationRate | 1.3.6.1.4.1.135.22.2.3.3 | INTEGER | read-write | AFA deactivation rate is used by the managed node to decide when it will enable the operational status of a T1 interface if the interface's BER rate is below the selected activation rate for a period specified by configAfaDectivationTime (see below). |
| INT configAfaDeactivationTime | 1.3.6.1.4.1.135.22.2.3.4 | INTEGER | read-write | See above description. Unit - minute |
| INT configAfaFarEndLpbkDetect | 1.3.6.1.4.1.135.22.2.3.6 | INTEGER | read-write | This object controls whether AFA will be activated when a near end LX-10 detects network loopback in the far end LX-10. If it's disabled, no AFA will be activated because of a far end network loopback. |
| INT configAfaStatus | 1.3.6.1.4.1.135.22.2.3.5 | INTEGER | read-write | Enable/disable AFA function. |
| INT configDs1AdminStatus | 1.3.6.1.4.1.135.22.2.1.1.2 | INTEGER | read-write | DS1 administrative status. |
| INT configDs1Encoding | 1.3.6.1.4.1.135.22.2.1.1.5 | INTEGER | read-write | Encoding. This object is not accessible if the managed node is the E1 version of LX10. |
| configDs1Entry | 1.3.6.1.4.1.135.22.2.1.1 | not-accessible | Each entry contains the configuration attributes for a DS1 port. | |
| INT configDs1Framing | 1.3.6.1.4.1.135.22.2.1.1.6 | INTEGER | read-write | Framing format. This object is not accessible if the managed node is the E1 version of LX10. |
| INT configDs1LBO | 1.3.6.1.4.1.135.22.2.1.1.4 | INTEGER | read-write | LBO. This object is not accessible if the managed node is the E1 version of LX10. |
| INT configDs1OperStatus | 1.3.6.1.4.1.135.22.2.1.1.3 | INTEGER | read-only | DS1 operational status. |
| INT configDs1Port | 1.3.6.1.4.1.135.22.2.1.1.1 | INTEGER | read-only | DS1 port number. |
| configDs1Table | 1.3.6.1.4.1.135.22.2.1 | not-accessible | DS1 configuration table. | |
| INT configDs1Timing | 1.3.6.1.4.1.135.22.2.2 | INTEGER | read-write | DS1 clock Source. |
| INT configDs1XmtAis | 1.3.6.1.4.1.135.22.2.1.1.7 | INTEGER | read-write | Enable/disable transmit AIS. |
| configHdlc | 1.3.6.1.4.1.135.22.2.6 | |||
| INT configHdlcFarEndPort | 1.3.6.1.4.1.135.22.2.6.3 | INTEGER | read-only | The DS1 port currently being used as the HDLC port in the far end LX-10. |
| INT configHdlcLocalPort | 1.3.6.1.4.1.135.22.2.6.2 | INTEGER | read-write | Assign one of the DS1 ports as the HDLC port. If its value is 0, no port is asssigned as the HDLC port. |
| INT configHdlcMode | 1.3.6.1.4.1.135.22.2.6.1 | INTEGER | read-write | Select the way in which HDLC port will be assigned. If mode is manual, the HDLC port is selectable by the NMS. If mode is auto, the 2 LX-10's in the 2 sides will match their HDLC ports automatically. |
| configHsdp | 1.3.6.1.4.1.135.22.2.5 | |||
| INT configHsdpCtsControl | 1.3.6.1.4.1.135.22.2.5.2 | INTEGER | read-write | CTS line control in HSDP. If the value of an instance of this object is set, the CTS line will always be set. If the value of an instance of this object is no-bandwidth, the CTS line will go low when no bandwidth is available after a hold-off time. If the value of an instance of this object is frequency- change, the CTS line will go low for a hold-off time when there is a frequency change. |
| INT configHsdpCtsStatus | 1.3.6.1.4.1.135.22.2.5.3 | INTEGER | read-only | Status of CTS line in HSDP. |
| INT configHsdpHoldoffSeconds | 1.3.6.1.4.1.135.22.2.5.7 | INTEGER | read-write | Hold-off time for CA lead. If the hold-off is set at 5 seconds, and if the CTS control is sensitive to no-bandwidth, the CTS line will go low after 5 seconds when no bandwidth is available. If the CTS control is sensitive to frequency-change, the CTS line will stay low for 5 seconds when there is a frequency change, and then back to high. |
| INT configHsdpMode | 1.3.6.1.4.1.135.22.2.5.1 | INTEGER | read-write | Interface type used by HSDP. |
| INT configHsdpRecvTiming | 1.3.6.1.4.1.135.22.2.5.6 | INTEGER | read-write | Status of receive timing in HSDP. It applies only when the value of the instance of configHsdpMode is v-35 or rs-422. |
| INT configHsdpTermTiming | 1.3.6.1.4.1.135.22.2.5.5 | INTEGER | read-write | Status of terminal timing in HSDP. It applies only when the value of the instance of configHsdpMode is v-35 or rs-422. |
| INT configHsdpTermTimingSource | 1.3.6.1.4.1.135.22.2.5.4 | INTEGER | read-write | Terminal timing source in HSDP. It applies only when the value of the instance of configHsdpMode is v-35 or rs-422. |
| INT configInverseMux | 1.3.6.1.4.1.135.22.2.7 | INTEGER | read-write | Master/slave relationship of the 2 LX-10E's in the point to point connection. |
| INT configPortCardType | 1.3.6.1.4.1.135.22.2.4 | INTEGER | read-only | There are 3 kinds of cards/port supported by the managed node: HSDP, Ethernet, or Token-Ring. Only one of them can be installed in the managed node. Hsdp is a high speed data port with v.35, rs-422, and HSSI interfaces. |
| enetPortCardStats | 1.3.6.1.4.1.135.22.4.3 | |||
| CTR enetPortCardStatsAlignmentErrors | 1.3.6.1.4.1.135.22.4.3.5 | Counter | read-only | A count of frames received that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. |
| CTR enetPortCardStatsBytesReceived | 1.3.6.1.4.1.135.22.4.3.2 | Counter | read-only | A count of bytes received by the ethernet port card. |
| CTR enetPortCardStatsBytesTransmitted | 1.3.6.1.4.1.135.22.4.3.4 | Counter | read-only | A count of bytes transmitted on the ethernet port card. |
| CTR enetPortCardStatsCarrierSenseErrors | 1.3.6.1.4.1.135.22.4.3.13 | Counter | read-only | The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt. |
| CTR enetPortCardStatsDeferredTransmissions | 1.3.6.1.4.1.135.22.4.3.9 | Counter | read-only | A count of frames for which the first transmission attempt is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions. |
| CTR enetPortCardStatsExcessiveCollisions | 1.3.6.1.4.1.135.22.4.3.11 | Counter | read-only | A count of frames for which transmission fails due to excessive collisions. |
| CTR enetPortCardStatsFCSErrors | 1.3.6.1.4.1.135.22.4.3.6 | Counter | read-only | A count of frames received that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. |
| CTR enetPortCardStatsFramesReceived | 1.3.6.1.4.1.135.22.4.3.1 | Counter | read-only | A count of frames received by the ethernet port card. |
| CTR enetPortCardStatsFramesTransmitted | 1.3.6.1.4.1.135.22.4.3.3 | Counter | read-only | A count of frames transmitted on the ethernet port card. |
| CTR enetPortCardStatsFrameTooLongs | 1.3.6.1.4.1.135.22.4.3.14 | Counter | read-only | A count of frames received that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. |
| CTR enetPortCardStatsInternalMacTransmitErrors | 1.3.6.1.4.1.135.22.4.3.12 | Counter | read-only | A count of frames for which transmission fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the enetPortCardStatsLateCollisions object, the enetPortCardStatsExcessiveCollisions object, or the enetPortCardStatsCarrierSenseErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of transmission errors that are not otherwise counted. |
| CTR enetPortCardStatsLateCollisions | 1.3.6.1.4.1.135.22.4.3.10 | Counter | read-only | The number of times that a collision is detected on later than 512 bit-times into the transmission of a packet. Five hundred and twelve bit-times corresponds to 51.2 microseconds on a 10 Mbit/s system. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics. |
| CTR enetPortCardStatsMultipleCollisionFrames | 1.3.6.1.4.1.135.22.4.3.8 | Counter | read-only | A count of successfully transmitted frames for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is not counted by the corresponding instance of the enetPortCardStatsSingleCollisionFrames object. |
| CTR enetPortCardStatsSingleCollisionFrames | 1.3.6.1.4.1.135.22.4.3.7 | Counter | read-only | A count of successfully transmitted frames for which transmission is inhibited by exactly one collision. A frame that is counted by an instance of this object is not counted by the corresponding instance of the enetPortCardStatsMultipleCollisionFrames object. |
| fault | 1.3.6.1.4.1.135.22.3 | |||
| INT faultClearCurrentAlarms | 1.3.6.1.4.1.135.22.3.3 | INTEGER | read-write | A set request clears all entries in the current alarm table. A get/get-next request returns 0. |
| INT faultClearHistoryAlarms | 1.3.6.1.4.1.135.22.3.4 | INTEGER | read-write | A set request clears all entries in the history alarm table. A get/get-next request returns 0. |
| INT faultCurrentAlarmAlarmType | 1.3.6.1.4.1.135.22.3.5.1.2 | INTEGER | read-only | The alarm type of the alarm. |
| INT faultCurrentAlarmCardType | 1.3.6.1.4.1.135.22.3.5.1.4 | INTEGER | read-only | The type of the card which caused the alarm. |
| STR faultCurrentAlarmDescription | 1.3.6.1.4.1.135.22.3.5.1.8 | DisplayString | read-only | A readable string which describes the alarm. Its format is as follows: 'Level' is the alarm severity. Its value can be 'Info', 'Major', or 'Minor'. 'Card' refers to where the alarm was generated. Its value can be 'HSDP', 'ENET', 'TRING', or 'DS1'. 'Port' refers to which port generated the alarm. Its value can be 1 to 7 for DS1 and 'empty' if no port number can be used for an alarm. 'Alarm Type' is an ASCII string of the alarm type. 'Time Occured' is the time when the alarm was generated. |
| faultCurrentAlarmEntry | 1.3.6.1.4.1.135.22.3.5.1 | not-accessible | Each entry in the table contains the information of a currently active alarm. | |
| INT faultCurrentAlarmPortNumber | 1.3.6.1.4.1.135.22.3.5.1.5 | INTEGER | read-only | The port number of the card which caused the alarm. Its value is between 1 and 7 for DS1 ports and 0 for others. |
| TIM faultCurrentAlarmSetTime | 1.3.6.1.4.1.135.22.3.5.1.6 | TimeAndDate | read-only | The time when the alarm was set. |
| INT faultCurrentAlarmSeverity | 1.3.6.1.4.1.135.22.3.5.1.3 | INTEGER | read-only | The severity of the alarm. |
| faultCurrentAlarmTable | 1.3.6.1.4.1.135.22.3.5 | not-accessible | Current alarm table. | |
| INT faultCurrentAlarmTag | 1.3.6.1.4.1.135.22.3.5.1.1 | INTEGER | read-only | The tag of the alarm in the current alarm table. |
| faultDs1 | 1.3.6.1.4.1.135.22.3.1 | |||
| faultDs1LoopbackEntry | 1.3.6.1.4.1.135.22.3.1.1.1 | not-accessible | Each entry in the table contains the loopback status of a DS1 port. | |
| INT faultDs1LoopbackNetworkLoopback | 1.3.6.1.4.1.135.22.3.1.1.1.2 | INTEGER | read-write | DS1 loopback is used to control the loopback state of one of the 7 DS1 interfaces in the managed node. |
| INT faultDs1LoopbackPort | 1.3.6.1.4.1.135.22.3.1.1.1.1 | INTEGER | read-only | The port number of one of the 7 DS1 ports |
| faultDs1LoopbackTable | 1.3.6.1.4.1.135.22.3.1.1 | not-accessible | DS1 loopback table for 7 DS1 ports. | |
| INT faultDs1RemoteLineLoopback | 1.3.6.1.4.1.135.22.3.1.2 | INTEGER | read-only | This loopback status is controlled by the LA/LB leads in the remote node. |
| faultDte | 1.3.6.1.4.1.135.22.3.2 | |||
| INT faultDteCustomerLoopback | 1.3.6.1.4.1.135.22.3.2.5 | INTEGER | read-write | Enable/disable the customer equipment (DTE) to perform loopback toward the managed node. |
| INT faultDteDteLoopback | 1.3.6.1.4.1.135.22.3.2.6 | INTEGER | read-write | Enable/disable the managed node to perform loopback toward the customer equipment (DTE). |
| INT faultDteLaLbLoopbackEnable | 1.3.6.1.4.1.135.22.3.2.4 | INTEGER | read-write | Enable/disable the managed node to use the LA and LB lead states to perform loopbaks. |
| INT faultDteLaLbTranslation | 1.3.6.1.4.1.135.22.3.2.3 | INTEGER | read-only | The managed node uses the states of the LA and LB leads to decide what kind of loopback to perform if faultLaLbLoopbackEnable (see below) is ENABLED. The meaning of LA and LB leads is as follows: loopback LA-Lead LB-Lead ------------------------------------------------ none clear clear local-line set clear remote-line clear set dte set set |
| INT faultDteLaLead | 1.3.6.1.4.1.135.22.3.2.1 | INTEGER | read-only | The state of the LA loopbak lead. |
| INT faultDteLbLead | 1.3.6.1.4.1.135.22.3.2.2 | INTEGER | read-only | The state of the LB loopbak lead. |
| INT faultHistoryAlarmAlarmType | 1.3.6.1.4.1.135.22.3.6.1.2 | INTEGER | read-only | The alarm type of the alarm. |
| INT faultHistoryAlarmCardType | 1.3.6.1.4.1.135.22.3.6.1.4 | INTEGER | read-only | The type of the card which caused the alarm. |
| TIM faultHistoryAlarmClearTime | 1.3.6.1.4.1.135.22.3.6.1.7 | TimeAndDate | read-only | The time when the alarm was cleared. |
| STR faultHistoryAlarmDescription | 1.3.6.1.4.1.135.22.3.6.1.8 | DisplayString | read-only | A readable string which describes the alarm. Its format is as follows: 'Level' is the alarm severity. Its value can be 'Info', 'Major', or 'Minor'. 'Card' refers to where the alarm was generated. Its value can be 'HSDP', 'ENET', 'TRING', or 'DS1'. 'Port' refers to which port generated the alarm. Its value can be 1 to 7 for DS1 and 'empty' if no port number can be used for an alarm. 'Alarm Type' is an ASCII string of the alarm type. 'Time Occured' is the time when the alarm was generated. 'Time Cleared' is the time when the alarm was cleared. |
| faultHistoryAlarmEntry | 1.3.6.1.4.1.135.22.3.6.1 | not-accessible | Each entry in the history alarm table contains either a cleared alarm or an information alarm. | |
| INT faultHistoryAlarmPortNumber | 1.3.6.1.4.1.135.22.3.6.1.5 | INTEGER | read-only | The port number of the card which caused the alarm. Its value is between 1 and 7 for DS1 ports and 0 for others. |
| TIM faultHistoryAlarmSetTime | 1.3.6.1.4.1.135.22.3.6.1.6 | TimeAndDate | read-only | The time when the alarm was set. |
| INT faultHistoryAlarmSeverity | 1.3.6.1.4.1.135.22.3.6.1.3 | INTEGER | read-only | The severity of the alarm. Its value can be either major or minor for DS1 ports and info for others. |
| faultHistoryAlarmTable | 1.3.6.1.4.1.135.22.3.6 | not-accessible | History/Information alarm table. | |
| INT faultHistoryAlarmTag | 1.3.6.1.4.1.135.22.3.6.1.1 | INTEGER | read-only | The tag of the alarm in the history alarm table. |
| lx_10 | 1.3.6.1.4.1.135.22 | |||
| nxt1PortStats | 1.3.6.1.4.1.135.22.4.5 | |||
| CTR nxt1PortStatsBytesReceived | 1.3.6.1.4.1.135.22.4.5.2 | Counter | read-only | A count of bytes received by the NxT1 port. |
| CTR nxt1PortStatsBytesTransmitted | 1.3.6.1.4.1.135.22.4.5.4 | Counter | read-only | A count of bytes transmitted on the NxT1 port. |
| CTR nxt1PortStatsCrcErrors | 1.3.6.1.4.1.135.22.4.5.5 | Counter | read-only | A count of frames received by the NxT1 port that do not pass the CRC check. |
| CTR nxt1PortStatsFramesReceived | 1.3.6.1.4.1.135.22.4.5.1 | Counter | read-only | A count of frames received by the NxT1 port. |
| CTR nxt1PortStatsFramesTransmitted | 1.3.6.1.4.1.135.22.4.5.3 | Counter | read-only | A count of frames transmitted on the NxT1 port. |
| onstream | 1.3.6.1.4.1.135 | |||
| perf | 1.3.6.1.4.1.135.22.4 | |||
| INT perfClearDs1Performance | 1.3.6.1.4.1.135.22.4.1 | INTEGER | read-write | A set request clears all DS1 performance monitoring data. A get/get-next request returns 0. |
| INT perfClearEnetPortCardStats | 1.3.6.1.4.1.135.22.4.2 | INTEGER | read-write | A set request clears all ethernet port card statistics. A get/get-next request returns 0. |
| INT perfClearNxT1PortStats | 1.3.6.1.4.1.135.22.4.4 | INTEGER | read-write | A set request clears all nxt1 port statistics. A get/get-next request returns 0. |
| sys | 1.3.6.1.4.1.135.22.1 | |||
| sysGenInfo | 1.3.6.1.4.1.135.22.1.1 | |||
| INT sysGenInfoAutoLogoutTime | 1.3.6.1.4.1.135.22.1.1.6 | INTEGER | read-write | The time a TELNET or VT-100 terminal user can maintain a session with the managed node without any keyboard action. Unit: minute |
| STR sysGenInfoCustomerName | 1.3.6.1.4.1.135.22.1.1.2 | DisplayString | read-write | Name of the organization that uses the managed node. |
| STR sysGenInfoLocation | 1.3.6.1.4.1.135.22.1.1.5 | DisplayString | read-write | Location of the managed node. |
| STR sysGenInfoMaintenanceContact | 1.3.6.1.4.1.135.22.1.1.4 | DisplayString | read-write | Maintenance contact of the managed node. |
| OCT sysGenInfoPassword | 1.3.6.1.4.1.135.22.1.1.7 | OCTET STRING | read-write | Password required to access the managed node using VT-100 terminal or TELNET. A get request always returns a NULL string. |
| STR sysGenInfoPhoneNumber | 1.3.6.1.4.1.135.22.1.1.3 | DisplayString | read-write | Phone number of the organization that uses the managed node. |
| INT sysGenInfoShelfId | 1.3.6.1.4.1.135.22.1.1.8 | INTEGER | read-write | LX-10 unit identification number required to identify and set up the device's role (primary/secondary). This number should be unique among interconnected devices. |
| STR sysGenInfoShelfName | 1.3.6.1.4.1.135.22.1.1.1 | DisplayString | read-write | Name of the managed node. |
| sysIpConfig | 1.3.6.1.4.1.135.22.1.3 | |||
| STR sysIpConfigCommunityName | 1.3.6.1.4.1.135.22.1.3.4 | DisplayString | read-write | Community name of the managed node. A get request for an instance of this object always returns a NULL string. |
| sysIpConfigDefaultGateway | 1.3.6.1.4.1.135.22.1.3.2 | |||
| IP sysIpConfigDefaultGatewayIpAddress | 1.3.6.1.4.1.135.22.1.3.2.1 | IpAddress | read-write | Default gateway's IP address. |
| IP sysIpConfigDefaultGatewaySubnetMask | 1.3.6.1.4.1.135.22.1.3.2.2 | IpAddress | read-write | Default gateway's IP subnet mask. |
| sysIpConfigHostInterfaceEntry | 1.3.6.1.4.1.135.22.1.3.1.1 | not-accessible | Each entry contains the IP address and subnet mask of the specified interface and a flag which enables/disables the managed node to broadcast its (RIP) routing table through the interface. | |
| INT sysIpConfigHostInterfaceIndex | 1.3.6.1.4.1.135.22.1.3.1.1.1 | INTEGER | read-only | |
| IP sysIpConfigHostInterfaceIpAddress | 1.3.6.1.4.1.135.22.1.3.1.1.2 | IpAddress | read-only | Host's IP address. |
| IP sysIpConfigHostInterfaceSubnetMask | 1.3.6.1.4.1.135.22.1.3.1.1.3 | IpAddress | read-only | Host's IP subnet mask. |
| sysIpConfigHostInterfaceTable | 1.3.6.1.4.1.135.22.1.3.1 | not-accessible | Table of available host IP interfaces. | |
| INT sysIpConfigHostInterfaceXmtRoutingMsg | 1.3.6.1.4.1.135.22.1.3.1.1.4 | INTEGER | read-write | This object controls whether the managed node should broadcast its (RIP) routing table through the interface. |
| PHY sysIpConfigMacAddress | 1.3.6.1.4.1.135.22.1.3.5 | PhysAddress | read-only | MAC-layer address of the management Ethernet port. |
| sysIpConfigTrapClientEntry | 1.3.6.1.4.1.135.22.1.3.3.1 | not-accessible | Each entry contains IP address and port number of an SNMP manager which receives traps from the managed node. | |
| INT sysIpConfigTrapClientIndex | 1.3.6.1.4.1.135.22.1.3.3.1.1 | INTEGER | read-write | |
| IP sysIpConfigTrapClientIpAddress | 1.3.6.1.4.1.135.22.1.3.3.1.2 | IpAddress | read-write | Trap client's IP address. |
| INT sysIpConfigTrapClientPortNumber | 1.3.6.1.4.1.135.22.1.3.3.1.4 | INTEGER | read-write | Trap client's port number. |
| IP sysIpConfigTrapClientSubnetMask | 1.3.6.1.4.1.135.22.1.3.3.1.3 | IpAddress | read-write | Trap client's IP subnet mask. |
| sysIpConfigTrapClientTable | 1.3.6.1.4.1.135.22.1.3.3 | not-accessible | Trap client table has 4 entries | |
| STR sysMainProcessorFirmwareRev | 1.3.6.1.4.1.135.22.1.5 | DisplayString | read-only | Firmware revision of the management CPU. |
| STR sysPortCardFirmwareRev | 1.3.6.1.4.1.135.22.1.6 | DisplayString | read-only | Firmware revision of the Ethernet (DATA) card. |
| INT sysRs232BaudRate | 1.3.6.1.4.1.135.22.1.4.1.2 | INTEGER | read-write | Baud rate. The instance of this object in port-1 is read-only. |
| INT sysRs232DataBits | 1.3.6.1.4.1.135.22.1.4.1.4 | INTEGER | read-write | Number of data bits. The instance of this object in port-1 is read-only. |
| sysRs232Entry | 1.3.6.1.4.1.135.22.1.4.1 | not-accessible | Each entry contains the attributes of a serial port. | |
| INT sysRs232Parity | 1.3.6.1.4.1.135.22.1.4.1.3 | INTEGER | read-write | Parity. The instance of this object in port-1 is read-only. |
| INT sysRs232Port | 1.3.6.1.4.1.135.22.1.4.1.1 | INTEGER | read-only | The managed node has 2 serial ports: port 1 and port 2. |
| INT sysRs232StopBits | 1.3.6.1.4.1.135.22.1.4.1.5 | INTEGER | read-write | Number of stop bits. The instance of this object in port-1 is read-only. |
| sysRs232Table | 1.3.6.1.4.1.135.22.1.4 | not-accessible | This table contains 2 rows. The first row shows the physical configuration of the port connected to a VT100 termianl. The second row is used to configure the port which supports SLIP. Access to the first row is read-only and access to the second row is read-write. | |
| TIM sysTimeAndDate | 1.3.6.1.4.1.135.22.1.2 | TimeAndDate | read-write | Time and date maintained in the managed node. |
RFC description
OnStream LX-10 tape system MIB for DS1 performance, configuration, fault, and system administration.
Start monitoring terminal/console servers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.