| OID symbolic | OID numeric | Type | Access | Description |
|---|
| juniDs1MIB | 1.3.6.1.4.1.4874.2.2.5 | | | The DS1/E1 MIB for the Juniper enterprise. This MIB contains managed
objects to supplement those found in RFC1406 DS1/E1 MIB. |
| juniDs1Objects | 1.3.6.1.4.1.4874.2.2.5.1 | | | |
| juniDsx1ConfigTable | 1.3.6.1.4.1.4874.2.2.5.1.1 | | not-accessible | This table contains entries for DS1/E1 interfaces present in the
system. |
| juniDsx1ConfigEntry | 1.3.6.1.4.1.4874.2.2.5.1.1.1 | | not-accessible | Each entry describes the characteristics of an DS1/E1 interface. |
| JUN juniDsx1TimeSlotMap | 1.3.6.1.4.1.4874.2.2.5.1.1.1.1 | JuniTimeSlotMap | read-only | A bitmap representing the timeslots on the DS1/E1 interface that have
been allocated for service.
For channelized DS1/E1, set bits reflect the union of timeslot
allocations across all fractional arrangements operating over this
DS1/E1 interface.
For unchannelized DS1/E1, all relevant timeslot bits will be set. |
| I32 juniDsx1Ds1ChannelNumber | 1.3.6.1.4.1.4874.2.2.5.1.1.1.2 | Integer32 | read-create | This variable represents the channel number of the DS1/E1 on its parent
DS3/E3. A value of 0 indicates this DS1/E1 does not have a parent
DS3/E3. |
| I32 juniDsx1Capabilities | 1.3.6.1.4.1.4874.2.2.5.1.1.1.3 | Integer32 | read-only | A value which indicates the set of capabilities of the DS1/E1
interface.
The value is a sum. This sum initially takes the value zero. Then, for
each capability, C, in the range 1 through 3, that this interface
supports, 2 raised to (C - 1) is added to the sum. For example, an
interface which is only E1 capable would have a value of 2 (2^(2-1)).
In contrast, an interface which is both T1 and J1 capable would have a
value of 5 (2^(1-1) + 2^(3-1)). The values for DS1/E1 interface
capabilities are as follows:
capability function
1 T1
2 E1
3 J1 |
| INT juniDsx1Mode | 1.3.6.1.4.1.4874.2.2.5.1.1.1.4 | INTEGER | read-create | This variable represents the DS1/E1 interface mode. The value of the
juniDsx1Capabilities object for the DS1/E1 interface indicates the valid
set of values for this object. |
| I32 juniDsx1LineBuildOutCapabilities | 1.3.6.1.4.1.4874.2.2.5.1.1.1.5 | Integer32 | read-only | A value which indicates the set of line build out capabilities of the
DS1/E1 interface.
The value is a sum. This sum initially takes the value zero. Then, for
each line build out capability, C, in the range 1 or 2, that this
interface supports, 2 raised to (C - 1) is added to the sum. For
example, an interface which is only short haul capable would have a
value of 2 (2^(2-1)). In contrast, an interface which is both short
haul and long haul capable would have a value of 3 (2^(1-1) + 2^(2-1)).
The values for DS1/E1 interface line build out capabilities are as
follows:
line build out capability function
1 short haul
2 long haul |
| INT juniDsx1LineBuildOutType | 1.3.6.1.4.1.4874.2.2.5.1.1.1.6 | INTEGER | read-create | This variable represents the configured line build out type of the
DS1/E1 interface. The value of the juniDsx1LineBuildOutCapabilities
object for the DS1/E1 interface indicates the valid set of values for
this object. |
| INT juniDsx1LineAttenuation | 1.3.6.1.4.1.4874.2.2.5.1.1.1.7 | INTEGER | read-create | This variable represents the configured line attenuation of the DS1/E1
interface. Note that the value of this object only takes effect when
the value of the juniDsx1LineBuildOutType for the DS1/E1 interface is
set to longHaul(2). |
| I32 juniDsx1LineLength | 1.3.6.1.4.1.4874.2.2.5.1.1.1.8 | Integer32 | read-create | This variable represents the length of the DS1/E1 line in meters. Note
that the value of this object only takes effect when the value of the
juniDsx1LineBuildOutType for the DS1/E1 interface is set to
shortHaul(1). |
| NUM juniDsx1LowerIfIndex | 1.3.6.1.4.1.4874.2.2.5.1.1.1.9 | InterfaceIndexOrZero | read-create | The ifIndex of the interface over which this Dsx1 interface is to be
layered. A value of zero indicates no layering. An implementation may
choose to require that a nonzero value be configured at entry creation. |
| ROW juniDsx1RowStatus | 1.3.6.1.4.1.4874.2.2.5.1.1.1.10 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
juniDsx1RowStatus
juniDsx1LowerIfIndex
In addition, when creating an entry the following conditions must hold:
A value for ifIndex must have been determined previously, by reading
juniDsx1NextIfIndex.
The interface identified by juniDsx1hLowerIfIndex must exist.
A corresponding entry in ifTable/ifXTable/juniIfTable is created/
destroyed as a result of creating/destroying an entry in this table. |
| INT juniDsx1SendCode | 1.3.6.1.4.1.4874.2.2.5.1.1.1.11 | INTEGER | read-create | This variable indicates what type of code is being sent across the DS1
interface by the device. |
| INT juniDsx1YellowAlarm | 1.3.6.1.4.1.4874.2.2.5.1.1.1.12 | INTEGER | read-create | This bitmap indicates the yellow alarm settings, and is the sum of the
capabilities. |
| INT juniDsx1RemoteLoopback | 1.3.6.1.4.1.4874.2.2.5.1.1.1.13 | INTEGER | read-create | This variable indicates the remote loopback setting. |
| INT juniDsx1FdlCarrier | 1.3.6.1.4.1.4874.2.2.5.1.1.1.14 | INTEGER | read-create | Specifies the interface is used in carrier environment. |
| STR juniDsx1FdlEic | 1.3.6.1.4.1.4874.2.2.5.1.1.1.15 | DisplayString | read-create | This is the equipment identification code. |
| STR juniDsx1FdlLic | 1.3.6.1.4.1.4874.2.2.5.1.1.1.16 | DisplayString | read-create | This is the location identification code. |
| STR juniDsx1FdlFic | 1.3.6.1.4.1.4874.2.2.5.1.1.1.17 | DisplayString | read-create | This is the frame identification code. |
| STR juniDsx1FdlUnit | 1.3.6.1.4.1.4874.2.2.5.1.1.1.18 | DisplayString | read-create | This is the unit identification code. |
| STR juniDsx1FdlPfi | 1.3.6.1.4.1.4874.2.2.5.1.1.1.19 | DisplayString | read-create | This is the facility identification code. |
| STR juniDsx1FdlPort | 1.3.6.1.4.1.4874.2.2.5.1.1.1.20 | DisplayString | read-create | This is the equipment port number. |
| STR juniDsx1FdlGenerator | 1.3.6.1.4.1.4874.2.2.5.1.1.1.21 | DisplayString | read-create | This is the generator number. |
| BIT juniDsx1FdlTransmit | 1.3.6.1.4.1.4874.2.2.5.1.1.1.22 | Bits | read-create | Specifies transmission enabling.
path - Bit 0 for path transmit. When this bit is set
indicates path transmit is enabled; otherwise
path transmit disabled.
idlesignal - Bit 1 for idlesignal transmit. When this bit
is set idlesingal transmit is enabled; otherwise
idlesignal transmit disabled.
testsignal - Bit 2 for testsignal transmit. When this bit
is set testsignal transmit is enabled; otherwise
testsignal transmit disabled.
The value of this object defaults to zero, indicating that none of FDL
transmit methods are enabled. |
| JUN juniDs1NextIfIndex | 1.3.6.1.4.1.4874.2.2.5.1.2 | JuniNextIfIndex | read-only | Coordinate ifIndex value allocation for entries in juniDsx1ConfigTable.
A GET of this object returns the next available ifIndex value to be used
to create an entry in the associated interface table; or zero, if no
valid ifIndex value is available. This object also returns a value of
zero when it is the lexicographic successor of a varbind presented in an
SNMP GETNEXT or GETBULK request, for which circumstance it is assumed
that ifIndex allocation is unintended.
Successive GETs will typically return different values, thus avoiding
collisions among cooperating management clients seeking to create table
entries simultaneously. |
| juniDsx1FarEndConfigTable | 1.3.6.1.4.1.4874.2.2.5.1.3 | | not-accessible | The DS1 Far End Configuration table. |
| juniDsx1FarEndConfigEntry | 1.3.6.1.4.1.4874.2.2.5.1.3.1 | | not-accessible | An entry in the DS1 Far End Configuration table. |
| INT juniDsx1FarEndLineIndex | 1.3.6.1.4.1.4874.2.2.5.1.3.1.1 | INTEGER | not-accessible | The index value which uniquely identifies the DS1 interface to which
this entry is applicable. The interface identified by a particular
value of this index is the same interface as identified by the same
value a dsx1LineIndex object instance. |
| STR juniDsx1FarEndEquipCode | 1.3.6.1.4.1.4874.2.2.5.1.3.1.2 | DisplayString | read-only | This is the Far End Equipment Identification code that describes the
specific piece of equipment. It is sent within the Path Identification
Message. |
| STR juniDsx1FarEndLocationIDCode | 1.3.6.1.4.1.4874.2.2.5.1.3.1.3 | DisplayString | read-only | This is the Far End Location Identification code that describes the
specific location of the equipment. It is sent within the Path
Identification Message. |
| STR juniDsx1FarEndFrameIDCode | 1.3.6.1.4.1.4874.2.2.5.1.3.1.4 | DisplayString | read-only | This is the Far End Frame Identification code that identifies where the
equipment is located within a building at a given location. It is sent
within the Path Identification Message. |
| STR juniDsx1FarEndUnitCode | 1.3.6.1.4.1.4874.2.2.5.1.3.1.5 | DisplayString | read-only | This is the Far End code that identifies the equipment location within
a bay. It is sent within the Path Identification Message. |
| STR juniDsx1FarEndFacilityIDCode | 1.3.6.1.4.1.4874.2.2.5.1.3.1.6 | DisplayString | read-only | This code identifies a specific Far End DS1 path. It is sent within
the Path Identification Message. |
| STR juniDsx1FarEndPortNumber | 1.3.6.1.4.1.4874.2.2.5.1.3.1.7 | DisplayString | read-only | This code identifies the port number of the Far End DS1. It is sent
within the Idle Signal Message. |
| STR juniDsx1FarEndGeneratorNumber | 1.3.6.1.4.1.4874.2.2.5.1.3.1.8 | DisplayString | read-only | This code identifies the Far End DS1 Generator Number. It is sent
within the Test Signal Message. |
| INT juniDsx1FarEndCarrier | 1.3.6.1.4.1.4874.2.2.5.1.3.1.9 | INTEGER | read-only | Specifies the interface is used in carrier environment. It is sent
with all FDL messages. |
| juniDs1Conformance | 1.3.6.1.4.1.4874.2.2.5.4 | | | |
| juniDs1Compliances | 1.3.6.1.4.1.4874.2.2.5.4.1 | | | |
| juniDs1Compliance | 1.3.6.1.4.1.4874.2.2.5.4.1.1 | | | Obsolete compliance statement for entities which implement the Juniper
DS1/E1 MIB. This statement became obsolete when new objects were
added. |
| juniDs1Compliance2 | 1.3.6.1.4.1.4874.2.2.5.4.1.2 | | | Obsolete compliance statement for entities which implement the Juniper
DS1/E1 MIB. This statement became obsolete when dynamic DS1 interface
support was added. |
| juniDs1Compliance3 | 1.3.6.1.4.1.4874.2.2.5.4.1.3 | | | Obsolete compliance statement for entities which implement the Juniper
DS1/E1 MIB. This statement became obsolete when FDL support was added. |
| juniDs1Compliance4 | 1.3.6.1.4.1.4874.2.2.5.4.1.4 | | | Obsolete compliance statement for entities which implement the Juniper
DS1/E1 MIB. This statement became obsolete when support for remote FDL
strings and FDL transmit mode was added. |
| juniDs1Compliance5 | 1.3.6.1.4.1.4874.2.2.5.4.1.5 | | | The compliance statement for entities which implement the Juniper
DS1/E1 MIB. |
| juniDs1Groups | 1.3.6.1.4.1.4874.2.2.5.4.2 | | | |
| juniDs1Group | 1.3.6.1.4.1.4874.2.2.5.4.2.1 | | | Obsolete collection of objects providing management of DS1/E1
interfaces in a Juniper product. This group became obsolete when new
objects where added to the MIB. |
| juniDs1Group2 | 1.3.6.1.4.1.4874.2.2.5.4.2.2 | | | Obsolete collection of objects providing management of DS1/E1
interfaces in a Juniper product. This group became obsolete when
dynamic DS1 interface support was added. |
| juniDs1Group3 | 1.3.6.1.4.1.4874.2.2.5.4.2.3 | | | Obsolete collection of objects providing management of DS1/E1
interfaces in a Juniper product. This group became obsolete when FDL
support was added. |
| juniDs1Group4 | 1.3.6.1.4.1.4874.2.2.5.4.2.4 | | | Obsolete collection of objects providing management of DS1/E1
interfaces in a Juniper product. This group became obsolete when
support for remote FDL strings and FDL transmit mode was added. |
| juniDs1Group5 | 1.3.6.1.4.1.4874.2.2.5.4.2.5 | | | A collection of objects providing management of DS1/E1 interfaces in a
Juniper product. |
