MDM-MIB

All MIBs › MDM-MIB

Category: Device Management, Domain: WAN

Description: Modem Device Management MIB defining SNMP objects for monitoring and controlling dial-up modem status, connections, and statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is MDM-MIB?

MDM-MIB is a Modem Device Management SNMP MIB, under an enterprise tree suggesting a US Robotics/3Com network access server (NAS) product family, defining objects for monitoring and controlling dial-up modem hardware, its connections, and call statistics within a modem pool. It exposes a modem identity table (mdmIDTable) with hardware serial number and hardware revision, plus separate firmware revision fields for the supervisor, data-pump, and I/O-processor subsystems, alongside a line-information table (mdmLiTable) covering per-line/per-call connection details. It is explicitly used for hardware and software status monitoring of each modem in a pool: mdmIDHardwareSerNum/mdmIDHardwareRev identify the physical unit, while mdmIDSupervisorSwRev, mdmIDDataPumpSwRev, and mdmIDIoProcessorSwRev report the firmware version running on each of the modem's three main subsystems, letting an operator confirm consistent firmware levels across a modem bank or spot an outdated unit. The enterprise path suggests it belongs to a vendor NAS product family rather than an IETF-standard MIB, and it would typically be polled alongside standard MIB-II interface objects for the NAS chassis. It is deployed on dial-up remote-access servers/modem racks used by ISPs or enterprises for dial-in connectivity. Engineers can download the MDM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in MDM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Dial-up modem / network access server (NAS) modem pool device

Monitoring Examples

An administrator would walk mdmIDTable/mdmIDEntry by mdmIDIndex to read mdmIDModel, mdmIDHardwareSerNum, and mdmIDHardwareRev for every modem in a rack, then check mdmIDSupervisorSwRev/mdmIDDataPumpSwRev/mdmIDIoProcessorSwRev to confirm all modems are running the same firmware set after a bulk upgrade. mdmIDCountry indicates the regulatory/dialing profile configured on each unit, useful for detecting a modem misconfigured for the wrong country's telephone network, and mdmLiTable would be checked for per-line call/connection status.

What Can Be Monitored

modem hardware serial number and revision
supervisor/data-pump/IO-processor firmware revision
modem model and country/regulatory profile
per-line connection status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks
enterprises
experimental

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
usr	1.3.6.1.4.1.429
nas	1.3.6.1.4.1.429.1
mdm	1.3.6.1.4.1.429.1.6
mdmID	1.3.6.1.4.1.429.1.6.1
mdmIDTable	1.3.6.1.4.1.429.1.6.1.1		not-accessible	A list of modem ID entries.
mdmIDEntry	1.3.6.1.4.1.429.1.6.1.1.1		not-accessible	An Identification table entry, containing objects which define the identity and capabilities of a modem.
INT mdmIDIndex	1.3.6.1.4.1.429.1.6.1.1.1.1	INTEGER	read-only	A unique value for each modem configured in the system based on the values in the entity table in the USR extensions to the chassis mib.
INT mdmIDModel	1.3.6.1.4.1.429.1.6.1.1.1.2	INTEGER	read-only	Defines the model (ie. V.23, HST, etc.) of the modem represented by this row in the table.
INT mdmIDCountry	1.3.6.1.4.1.429.1.6.1.1.1.3	INTEGER	read-only	This object identifies the country or countries that this modem is designed for use in.
STR mdmIDHardwareSerNum	1.3.6.1.4.1.429.1.6.1.1.1.4	DisplayString	read-only	The modem's hardware serial number as stored in EEPROM.
STR mdmIDHardwareRev	1.3.6.1.4.1.429.1.6.1.1.1.5	DisplayString	read-only	The hardware revision of the modem as stored in the modem's EEPROM.
STR mdmIDSupervisorSwRev	1.3.6.1.4.1.429.1.6.1.1.1.6	DisplayString	read-only	The revision of the software being executed by the modem's supervisor processor.
STR mdmIDDataPumpSwRev	1.3.6.1.4.1.429.1.6.1.1.1.7	DisplayString	read-only	The revision of software being executed by the modem's data pump processor.
STR mdmIDIoProcessorSwRev	1.3.6.1.4.1.429.1.6.1.1.1.8	DisplayString	read-only	The revison of software being executed by the modem's IO Control Processor.
STR mdmIDSupervisorDate	1.3.6.1.4.1.429.1.6.1.1.1.9	DisplayString	read-only	The supervisor build date.
mdmLi	1.3.6.1.4.1.429.1.6.2
mdmLiTable	1.3.6.1.4.1.429.1.6.2.1		not-accessible	A list of configurable Line Interface objects for a modem. The number of table entries is given by modemNumber.
mdmLiEntry	1.3.6.1.4.1.429.1.6.2.1.1		not-accessible	Objects which define the line interface characteristics for a particualar modem.
INT mdmLiIndex	1.3.6.1.4.1.429.1.6.2.1.1.1	INTEGER	read-only	Index into the Line Interface table. This index is the value from the chassis mib entity relation table that is applicable for a particular modem.
INT mdmLiDialPause	1.3.6.1.4.1.429.1.6.2.1.1.2	INTEGER	read-write	Duration in seconds for the pause(') option in the dial command and the pause between command re-executions(> and A>) Default = 2. Equates to the modem's S8 register.
INT mdmLiCarrierRecDelay	1.3.6.1.4.1.429.1.6.2.1.1.3	INTEGER	read-write	Duration in 10ths of a second that the remote modem's carrier signal must be present before recognition. Ignored at speeds above 2400. Equates to the modem's S9 register. Default=6.
INT mdmLiCarrierLoss	1.3.6.1.4.1.429.1.6.2.1.1.4	INTEGER	read-write	Duration in 10ths of a second the modem waits after loss of carrier before hanging up. This allows the modem to distinguish between a momentary lapse in line quality and a true disconnect. When equal to 255 the modem will remain off hook until DTR drops or an ATH command is recieved. Equates to the modem's S10 register. Default=7.
INT mdmLiToneDialTiming	1.3.6.1.4.1.429.1.6.2.1.1.5	INTEGER	read-write	Duration and spacing in milliseconds of dialed Touch Tones. Equates to the modem's S10 register. Default=70.
INT mdmLiDteRxDataDelay	1.3.6.1.4.1.429.1.6.2.1.1.6	INTEGER	read-write	Duration in 10ths of a second that the modem inserts a RX transmission delay between CD and the first recieved character. Intended for custom applications and not recomended for general usage. Equates to the modem's S35 register. Default=0.
INT mdmLiTransmiter	1.3.6.1.4.1.429.1.6.2.1.1.7	INTEGER	read-write	Enables the modem to transmit data. Corresponds to the modem 'C' register. Default=2.
INT mdmLiDialMode	1.3.6.1.4.1.429.1.6.2.1.1.8	INTEGER	read-write	Determines whether the modem uses pulse or tone for dialing when initiating outgoing calls. Equates to the P and T registers in the modem. Default=0.
INT mdmLiGuardTone	1.3.6.1.4.1.429.1.6.2.1.1.9	INTEGER	read-write	This object is required for modems answering calls that originate from sites outside of North America. The modem's must be operating in either 1200 or 2400 bps and be using the V.32 answer sequence. This object defines what guard tone is used for answering calls. This object equates to the &G register in US Robotics modems. Default=none.
INT mdmLiLeasedLine	1.3.6.1.4.1.429.1.6.2.1.1.10	INTEGER	read-write	Enables modem to operate in leased line mode. When enabled the local an remote modems make a continuous connection without dialing. Should the connection be broken the modem's will attempt to automaticly reestablish it(see mdmCcLeasedLineRest). Equates to the modem's &L register Default = disabled.
INT mdmLiLeasedLineRestDelay	1.3.6.1.4.1.429.1.6.2.1.1.11	INTEGER	read-write	Sets the duration, in seconds, of the delay between when the modem senses loss of carrier and when it attempts to reestablish a leased line connection. The default setting of 15 should be appropriate for most installations.
INT mdmLiPulseMakeBreak	1.3.6.1.4.1.429.1.6.2.1.1.12	INTEGER	read-write	Determines the ratio of off hook to on hook interval for Pulse dialing. Equates to the modem's &P register. Default=North America.
INT mdmLiAnswerTone	1.3.6.1.4.1.429.1.6.2.1.1.13	INTEGER	read-write	Disables the 2100 Hz Answer tone allowing V.42 modems to connect more quickly and/or eliminating problems with older 2400-bps modems that do not recognise this tone. Equates to the modem's S27.3 register. Default=Enabled.
INT mdmLiRemoteEscGuardTime	1.3.6.1.4.1.429.1.6.2.1.1.14	INTEGER	read-write	Sets the duration in 20 millisecond increments of the guard time that the modem requires preceding and following the remote escape sequence. The default is 200 or 4 seconds.
INT mdmLiRemoteEscChar	1.3.6.1.4.1.429.1.6.2.1.1.15	INTEGER	read-write	Specifies the decimal value of the character used in the remote access escape code for entering online command mode on this modem from the remote site. Default = 126(~).
INT mdmLiRemAccessLimit	1.3.6.1.4.1.429.1.6.2.1.1.16	INTEGER	read-write	Determines the number of attempts to enter remote online command mode that are allowed for any one connection. The default is 0 which disables the remote access functon.
STR mdmLiRemPassword0	1.3.6.1.4.1.429.1.6.2.1.1.17	DisplayString	read-write	The password that allows a dial-in user to gain view only access to this modems parameters. A maximum of 8 characters is allowed.
STR mdmLiRemPassword1	1.3.6.1.4.1.429.1.6.2.1.1.18	DisplayString	read-write	The password used by a dial-in user to gain read-write access to this modems configuration. Maximum length is 8 characters.
INT mdmLiTransmitLevel	1.3.6.1.4.1.429.1.6.2.1.1.19	INTEGER	read-write	Specifies the signal level of the modem transmitter in negative db.
INT mdmLiSrc	1.3.6.1.4.1.429.1.6.2.1.1.20	INTEGER	read-write	Specifies either NIC or TDM as the source for the line interface.
mdmDc	1.3.6.1.4.1.429.1.6.3
mdmDcTable	1.3.6.1.4.1.429.1.6.3.1		not-accessible	A table of configurable objects that define the operation of Data Compression in the modem.
mdmDcEntry	1.3.6.1.4.1.429.1.6.3.1.1		not-accessible	Objects which define Data Compression operation for a modem.
INT mdmDcIndex	1.3.6.1.4.1.429.1.6.3.1.1.1	INTEGER	read-only	The index into the Data Compression table. This object contains the unique value for this modem as defined in the chassis mib entity relation table.
INT mdmDcDataCompression	1.3.6.1.4.1.429.1.6.3.1.1.2	INTEGER	read-write	Determines when and how data compression is enabled. Corresponds to the &K register in USR modems.
mdmTf	1.3.6.1.4.1.429.1.6.4
mdmTfTable	1.3.6.1.4.1.429.1.6.4.1		not-accessible	Table of test functions for modems. There is a table entry for each modem the quantity of which is specified by modemNumber.
mdmTfEntry	1.3.6.1.4.1.429.1.6.4.1.1		not-accessible	Objects used to request thet the modem perform certain diagnostic tests.
INT mdmTfIndex	1.3.6.1.4.1.429.1.6.4.1.1.1	INTEGER	read-only	A unique value used to identify this modem the value of which is determined by the entity table in the chassis mib and used as a method to index into the test function table.
INT mdmTfTest	1.3.6.1.4.1.429.1.6.4.1.1.2	INTEGER	read-write	Equates to modem's S16 register.
INT mdmTfTestTime	1.3.6.1.4.1.429.1.6.4.1.1.3	INTEGER	read-write	Duration in seconds that the tests specified by mdmTfTestControl are to execute. Default=0(indefinate).
INT mdmTfV54	1.3.6.1.4.1.429.1.6.4.1.1.4	INTEGER	read-write	Corresponds to modem's &T register and provides tests specified by V.54. Default=normal.
INT mdmTfV54Errors	1.3.6.1.4.1.429.1.6.4.1.1.5	INTEGER	read-only	The number of errors occurring during the last V54 loopback test.
OCT mdmTfATG	1.3.6.1.4.1.429.1.6.4.1.1.6	OCTET STRING	read-only	ATG data from the modem
INT mdmTfDialInToneTest	1.3.6.1.4.1.429.1.6.4.1.1.7	INTEGER	read-write	This object is used to enable Dial in Tone Tests.
OCT mdmTfToneTestCallRef	1.3.6.1.4.1.429.1.6.4.1.1.8	OCTET STRING	read-only	This object is used to send the call reference info with the tone test.
mdmTfToneTable	1.3.6.1.4.1.429.1.6.4.2		not-accessible	Table for modem tone tests
mdmTfToneEntry	1.3.6.1.4.1.429.1.6.4.2.1		not-accessible	Objects for modem tone tests
INT mdmTfToneIndex	1.3.6.1.4.1.429.1.6.4.2.1.1	INTEGER	read-only	A value used to ID this modem
INT mdmTfTxFreq	1.3.6.1.4.1.429.1.6.4.2.1.2	INTEGER	read-write	Modem tone test TX frequency
INT mdmTfTxAmpl	1.3.6.1.4.1.429.1.6.4.2.1.3	INTEGER	read-write	Modem tone test TX amplitude
INT mdmTfRxFreq	1.3.6.1.4.1.429.1.6.4.2.1.4	INTEGER	read-only	Modem tone test RX frequency
INT mdmTfRxAmpl	1.3.6.1.4.1.429.1.6.4.2.1.5	INTEGER	read-only	Modem tone test RX amplitude
mdmTfRspndrTable	1.3.6.1.4.1.429.1.6.4.3		not-accessible	Table for 105/102 responder test results.
mdmTfRspndrEntry	1.3.6.1.4.1.429.1.6.4.3.1		not-accessible	Objects containing the 105/102 responder test result dB levels and test status values.
INT mdmTfRspndrIndex	1.3.6.1.4.1.429.1.6.4.3.1.1	INTEGER	read-only	A value used to ID this modem.
INT mdmTf404FarNearLvl	1.3.6.1.4.1.429.1.6.4.3.1.2	INTEGER	read-only	404 Hz tone at -16 dB loss test level. Far to near. Level in 0.1 dB resolution.
INT mdmTf404NearFarLvl	1.3.6.1.4.1.429.1.6.4.3.1.3	INTEGER	read-only	404 Hz tone at -16 dB loss test level. Near to far. Level in 0.1 dB resolution.
INT mdmTf1004FarNearLvl	1.3.6.1.4.1.429.1.6.4.3.1.4	INTEGER	read-only	1004 Hz tone at -16 dB loss test level. Far to near. Level in 0.1 dB resolution.
INT mdmTf1004NearFarLvl	1.3.6.1.4.1.429.1.6.4.3.1.5	INTEGER	read-only	1004 Hz tone at -16 dB loss test level. Near to far. Level in 0.1 dB resolution.
INT mdmTf2804FarNearLvl	1.3.6.1.4.1.429.1.6.4.3.1.6	INTEGER	read-only	2804 Hz tone at -16 dB loss test level. Far to near. Level in 0.1 dB resolution.
INT mdmTf2804NearFarLvl	1.3.6.1.4.1.429.1.6.4.3.1.7	INTEGER	read-only	2804 Hz tone at -16 dB loss test level. Near to far. Level in 0.1 dB resolution.
INT mdmTfCmsgFarNearLvl	1.3.6.1.4.1.429.1.6.4.3.1.8	INTEGER	read-only	C-message test level. Far to near. Level in 0.1 dB resolution.
INT mdmTfCmsgNearFarLvl	1.3.6.1.4.1.429.1.6.4.3.1.9	INTEGER	read-only	C-message test level. Near to far. Level in 0.1 dB resolution.
INT mdmTfCnotchFarNearLvl	1.3.6.1.4.1.429.1.6.4.3.1.10	INTEGER	read-only	C-notch test level. Far to near. Level in 0.1 dB resolution.
INT mdmTfCnotchNearFarLvl	1.3.6.1.4.1.429.1.6.4.3.1.11	INTEGER	read-only	C-notch test level. Near to far. Level in 0.1 dB resolution.
INT mdmtTfSigNoiseFarNearLvl	1.3.6.1.4.1.429.1.6.4.3.1.12	INTEGER	read-only	Signal to noise ratio level. Far to near. Level in 0.1 dB resolution.
INT mdmtTfSigNoiseNearFarLvl	1.3.6.1.4.1.429.1.6.4.3.1.13	INTEGER	read-only	Signal to noise ratio level. Near to far. Level in 0.1 dB resolution.
INT mdmTf404FarNearSts	1.3.6.1.4.1.429.1.6.4.3.1.14	INTEGER	read-only	404 Hz tone at -16 dB loss test status. Far to near. Default=noTest(1).
INT mdmTf404NearFarSts	1.3.6.1.4.1.429.1.6.4.3.1.15	INTEGER	read-only	404 Hz tone at -16 db loss test status. Near to far. Default=noTest(1).
INT mdmTf1004FarNearSts	1.3.6.1.4.1.429.1.6.4.3.1.16	INTEGER	read-only	1004 Hz tone at -16 dB loss test status. Far to near. Default=noTest(1).
INT mdmTf1004NearFarSts	1.3.6.1.4.1.429.1.6.4.3.1.17	INTEGER	read-only	1004 Hz tone at -16 dB loss test status. Near to far. Default=noTest(1).
INT mdmTf2804FarNearSts	1.3.6.1.4.1.429.1.6.4.3.1.18	INTEGER	read-only	2804 Hz tone at -16 dB loss test status. Far to near. Default=noTest(1).
INT mdmTf2804NearFarSts	1.3.6.1.4.1.429.1.6.4.3.1.19	INTEGER	read-only	2804 Hz tone at -16 dB loss test status. Near to far. Default=noTest(1).
INT mdmTfCmsgFarNearSts	1.3.6.1.4.1.429.1.6.4.3.1.20	INTEGER	read-only	C-message test status. Far to near. Default=noTest(1).
INT mdmTfCmsgNearFarSts	1.3.6.1.4.1.429.1.6.4.3.1.21	INTEGER	read-only	C-message test status. Near to far. Default=noTest(1).
INT mdmTfCnotchFarNearSts	1.3.6.1.4.1.429.1.6.4.3.1.22	INTEGER	read-only	C-notch test status. Far to near. Default=noTest(1).
INT mdmTfCnotchNearFarSts	1.3.6.1.4.1.429.1.6.4.3.1.23	INTEGER	read-only	C-notch test status. Near to far. Default=noTest(1).
INT mdmTfSigNoiseFarNearSts	1.3.6.1.4.1.429.1.6.4.3.1.24	INTEGER	read-only	Signal to noise ratio status. Far to near. Default=noTest(1).
INT mdmTfSigNoiseNearFarSts	1.3.6.1.4.1.429.1.6.4.3.1.25	INTEGER	read-only	Signal to noise ratio status. Near to far. Default=noTest(1).
INT mdmTf0dB1004FarNearLvl	1.3.6.1.4.1.429.1.6.4.3.1.26	INTEGER	read-only	1004 Hz tone at 0 db loss test level. Far to near. Level in 0.1 dB resolution.
INT mdmTf0dB1004NearFarLvl	1.3.6.1.4.1.429.1.6.4.3.1.27	INTEGER	read-only	1004 Hz tone at 0 db loss test level. Near to far. Level in 0.1 dB resolution.
INT mdmTf0dB1004FarNearSts	1.3.6.1.4.1.429.1.6.4.3.1.28	INTEGER	read-only	1004 Hz tone at 0 db loss test status. Far to near. Default=noTest(1).
INT mdmTf0dB1004NearFarSts	1.3.6.1.4.1.429.1.6.4.3.1.29	INTEGER	read-only	1004 Hz tone at 0 db loss test status. Near to Far. Default=noTest(1).
mdmDi	1.3.6.1.4.1.429.1.6.5
mdmDiTable	1.3.6.1.4.1.429.1.6.5.1		not-accessible	Table of DTE interface objects. The number of table entries is specified by modemNumber.
mdmDiEntry	1.3.6.1.4.1.429.1.6.5.1.1		not-accessible	Objects that define the DTE interface for a modem.
INT mdmDiIndex	1.3.6.1.4.1.429.1.6.5.1.1.1	INTEGER	read-only	The index for the DTE interface table contains the unique value associated with this modem as defined in the chassis mib entity table.
INT mdmDiEscCodeGuardTime	1.3.6.1.4.1.429.1.6.5.1.1.2	INTEGER	read-write	Duration in 50ths of a second of idle time that must precede and follow the modem's command mode escape code. Default=50.
INT mdmDiLocalEscChar	1.3.6.1.4.1.429.1.6.5.1.1.3	INTEGER	read-write	Decimal equivalent of the character that is used to escape to on-line command mode. Values between 128 and 255 disable the escape code. Default=43(+).
INT mdmDiCarriageRetChar	1.3.6.1.4.1.429.1.6.5.1.1.4	INTEGER	read-write	Specifies the decimal equivalent of the carriage return character. Default=13.
INT mdmDiLineFeedChar	1.3.6.1.4.1.429.1.6.5.1.1.5	INTEGER	read-write	Specifies the decimal equivalent of the line feed character. Default=10.
INT mdmDiBackspaceChar	1.3.6.1.4.1.429.1.6.5.1.1.6	INTEGER	read-write	Specifies the decimal equivalent of the backspace character. Default=8.
INT mdmDiDelAsBackspace	1.3.6.1.4.1.429.1.6.5.1.1.7	INTEGER	read-write	Defines functionality of the delete key. Acts either to delete the character the cursor is currently on or acts the same as the backspace key. Default=delete.
INT mdmDiResetOnDtrEna	1.3.6.1.4.1.429.1.6.5.1.1.8	INTEGER	read-write	When enabled, this option will cause the modem to restart when the DTR control signal drops. Default=disabled.
INT mdmDiResultCodePauseDis	1.3.6.1.4.1.429.1.6.5.1.1.9	INTEGER	read-write	When enabled, the modem pauses 250ms before transmission of any result code. Default=enable.
INT mdmDiInterbridgeEna	1.3.6.1.4.1.429.1.6.5.1.1.10	INTEGER	read-write	When enabled, the modem operates in a mode that is compatible with an 'Appletalk InterBridge Network'. Default=disabled.
INT mdmDiBreakLen	1.3.6.1.4.1.429.1.6.5.1.1.11	INTEGER	read-write	Defines the duration of break characters that are sent to the DTE in ARQ mode. Defined in 10ms increments. Default=10(100ms).
INT mdmDiXonChar	1.3.6.1.4.1.429.1.6.5.1.1.12	INTEGER	read-write	Defines the decimal equivalent of the Xon character. This character will be used when software flow control is enabled. Default=17.
INT mdmDiXoffChar	1.3.6.1.4.1.429.1.6.5.1.1.13	INTEGER	read-write	Defines the decimal equivalent of the xoff character. This character will be used when software flow control is enabled. Default=19.
INT mdmDiDsrPulseTime	1.3.6.1.4.1.429.1.6.5.1.1.14	INTEGER	read-write	Duration in 20 millisecond increments that the DSR signal is pulsed when the modem is configured for pulsed DSR mode. Default=150.
INT mdmDiRtsCtsDelay	1.3.6.1.4.1.429.1.6.5.1.1.15	INTEGER	read-write	Duration in 10 millisecond increments that the modem delays setting CTS after detecting the presence of RTS. Default=1.
INT mdmDiHiSpeedResCodeEna	1.3.6.1.4.1.429.1.6.5.1.1.16	INTEGER	read-write	Determines if connection establishment result codes above 9600 are sent to the DTE. Default=enable.
INT mdmDiCmdLocalEchoEna	1.3.6.1.4.1.429.1.6.5.1.1.17	INTEGER	read-write	Defines whether or not the characters transmitted by the DTE are echoed back when in command mode. Default=disabled.
INT mdmDiDataModeEchoEna	1.3.6.1.4.1.429.1.6.5.1.1.18	INTEGER	read-write	Defines whether or not the DTE's transmitted data is echoed back durring a connection(half duplex). Default=disabled.
INT mdmDiDteDataRateMode	1.3.6.1.4.1.429.1.6.5.1.1.19	INTEGER	read-write	Defines how the modem determines the DTE data rate. When set to the default, follows link rate, the modem switches the DTE speed to match the link rate. When set to fixed, the DTE speed remains at the default DTE data rate or the rate of the last AT command. When set to ARQ fixed-Non ARQ follows the dte speed remains fixed for ARQ calls and follows the link rate for non ARQ calls.
INT mdmDiCdOverride	1.3.6.1.4.1.429.1.6.5.1.1.20	INTEGER	read-write	Defines the operation of the CD(Carrier Detect) signal. When overridden the CD signal is always asserted. Default=normal.
INT mdmDiDtrOverride	1.3.6.1.4.1.429.1.6.5.1.1.21	INTEGER	read-write	Defines operation with regard to DTR. When overridden the DTR signal is always assumed to be present. Default=normal.
INT mdmDiDsrOverride	1.3.6.1.4.1.429.1.6.5.1.1.22	INTEGER	read-write	Determines the functionality of the modem's DSR signal. Default=Override.
INT mdmDiEiaLineStatus	1.3.6.1.4.1.429.1.6.5.1.1.23	INTEGER	read-only	Provides a mechanism for the console to determine the current state of the DTE's EIA signals.
INT mdmDiTransmitFlowCntl	1.3.6.1.4.1.429.1.6.5.1.1.24	INTEGER	read-write	Determines if transmit flow control is enabled and if so whether it is hardware or software. Default=none.
INT mdmDiSoftwareRxFlowCntl	1.3.6.1.4.1.429.1.6.5.1.1.25	INTEGER	read-write	Determines if receive software flow control is enabled as well as what type. Default=none.
INT mdmDiHardwareRxFlowCntl	1.3.6.1.4.1.429.1.6.5.1.1.26	INTEGER	read-write	Determines if receive hardware flow control is enabled as well as how it is implemented. Default=RTS ignored.
INT mdmDiBreakHandling	1.3.6.1.4.1.429.1.6.5.1.1.27	INTEGER	read-write	Defines the method used to handle received breaks. When defined as destructive the modem's transmit data buffer is flushed. When defined as expidited, the break preceeds any pending data in the transmit buffer. Default=Destructive,Expidited.
INT mdmDiDteNvramLock	1.3.6.1.4.1.429.1.6.5.1.1.28	INTEGER	read-write	When locked, prohibits the DTE user from changing any of the NVRAM settings in the modem. Default=unlocked.
INT mdmDiSerialFormat	1.3.6.1.4.1.429.1.6.5.1.1.29	INTEGER	read-write	Defines the data bits and parity of the modem's DTE. Used in situations where the attached DTE is unable to send AT commands to initialize the DTE format. Default=8 bit no parity.
INT mdmDiDefaultDteDataRate	1.3.6.1.4.1.429.1.6.5.1.1.30	INTEGER	read-write	Defines the data rate of the DTE. Useful in those cases where the DTE is incapable of sending an AT command to initialize the data rate and a fixed data rate is required. Default=9600.
INT mdmDiRemAccessMsg	1.3.6.1.4.1.429.1.6.5.1.1.31	INTEGER	read-write	Specifies if the modem is to send the 'Modem Unavailable' message to the DTE when the DTE attempts to send data to a modem that is curently in command mode with a remote DTE. Default = enabled.
INT mdmDiV25DteDataRate	1.3.6.1.4.1.429.1.6.5.1.1.32	INTEGER	read-write	Defines the DTE Data Rates supported for V25 bis.
INT mdmDiSrc	1.3.6.1.4.1.429.1.6.5.1.1.33	INTEGER	read-write	Specifies either NIC or Packet Bus as the source for the DTE interface.
INT mdmDiSlot	1.3.6.1.4.1.429.1.6.5.1.1.34	INTEGER	read-write	Specifies the slot address as the DTE interface source when mdmdiSrc is configured for Packet Bus.
INT mdmDiBusyClock	1.3.6.1.4.1.429.1.6.5.1.1.35	INTEGER	read-write	specifies whether the modem will support either the current transmit clock or a new busy out.
STR mdmDiAtString	1.3.6.1.4.1.429.1.6.5.1.1.36	DisplayString	read-write	Provides an interface for issuing an AT command to the modem. Not implemented as a command so as to allow the object to be saved to NVRAM and subsequently configured during power-up.
INT mdmDiDtrRecognitionTime	1.3.6.1.4.1.429.1.6.5.1.1.37	INTEGER	read-write	S25 register tells the modem how quickly to react when DTR transitions from off to on. Default is 20. Increments are in 10 ms.
mdmSc	1.3.6.1.4.1.429.1.6.6
mdmScTable	1.3.6.1.4.1.429.1.6.6.1		not-accessible	Table of configurable objects which determine the operation of the Signal Converter. The quantity of entries in this table is defined by modemNumber.
mdmScEntry	1.3.6.1.4.1.429.1.6.6.1.1		not-accessible	Objects that define the operation of the modem's Signal Converter.
INT mdmScIndex	1.3.6.1.4.1.429.1.6.6.1.1.1	INTEGER	read-only	The unique value found in the chassis mib entity relation table that references this modem.
INT mdmScLinkRateSelect	1.3.6.1.4.1.429.1.6.6.1.1.2	INTEGER	read-write	Determines if the link will run at a fixed or variable data rate. Default=variable.
INT mdmScNonArqBufSize	1.3.6.1.4.1.429.1.6.6.1.1.3	INTEGER	read-write	Sets the sizer of the transmit buffer for non-ARQ mode operation to either 128 bytes or 1.5K. The smaller size is for low speed interactive applications, the large size is for file transfer. Default=128.
INT mdmScNonMnpDataCapture	1.3.6.1.4.1.429.1.6.6.1.1.4	INTEGER	read-write	Causes received characters to be buffered when the modem is attempting to negotiate an MNP call and the remote modem is not. Default=disabled.
INT mdmScSyncTimingSource	1.3.6.1.4.1.429.1.6.6.1.1.5	INTEGER	read-write	Specifies the clock source when operating in synchronous mode. Default=internal.
INT mdmScHstMod	1.3.6.1.4.1.429.1.6.6.1.1.6	INTEGER	read-write	May be used to disable HST operation on USRobotics Dual Standard modems. Default=enable.
INT mdmScHiFreqEq	1.3.6.1.4.1.429.1.6.6.1.1.7	INTEGER	read-write	Allows modem's high frequency equalization to be disabled if it causes problems on shorter lines. Default=enabled.
INT mdmScBackChanRate	1.3.6.1.4.1.429.1.6.6.1.1.8	INTEGER	read-write	Specifies the lower speed used in the asymetrical (HST) mode of operation. The 300 bps setting is provided for compatibility with early HST modems. Default=450.
INT mdmScV21Mod	1.3.6.1.4.1.429.1.6.6.1.1.9	INTEGER	read-write	When enabled, the modem will answer both bell 103 and V.21 calls but originates only V.21 calls. Default=disabled.
INT mdmScV32UnencodedMod	1.3.6.1.4.1.429.1.6.6.1.1.10	INTEGER	read-write	Allows unencoded modulation in V.32 mode. Although part of the CCITT V.32 recomendation it is rarely used. Default=disabled.
INT mdmScV32Mod	1.3.6.1.4.1.429.1.6.6.1.1.11	INTEGER	read-write	Allows V.32 modulation to be disabled on USRobotics Dual Standard modems. Default=enabled.
INT mdmScBell208	1.3.6.1.4.1.429.1.6.6.1.1.12	INTEGER	read-write	Allows modems that support Bell 208 modulation to include Bell 208 as part of the negotiation sequence. Default=Bell 208 disabled.
INT mdmScV32Bis	1.3.6.1.4.1.429.1.6.6.1.1.13	INTEGER	read-write	Allows V.32 bis modulation to be disabled. On USRobotics Dual Standard modems this may be useful in troublshooting HST operation. Default=V.32 bis enabled.
INT mdmScV32BisEnhance	1.3.6.1.4.1.429.1.6.6.1.1.14	INTEGER	read-write	Allows USRobotics V.32 Enahnced mode to be disabled for purposes of troubleshooting Default=enabled.
INT mdmScV32QuickRetrain	1.3.6.1.4.1.429.1.6.6.1.1.15	INTEGER	read-write	Allows the faster retrains that occur with USR's enhanced V.32 mode to be disabled for troubleshooting purposes. Default=enabled.
INT mdmScV23	1.3.6.1.4.1.429.1.6.6.1.1.16	INTEGER	read-write	Allows the modem to negotiate a V.23 connection(used in U.K.) after failing to negotiate a higher rate. Default=disabled.
INT mdmScHiSpeedModulation	1.3.6.1.4.1.429.1.6.6.1.1.17	INTEGER	read-write	Defines the handshaking options used in negotiation of high speed calls. Default=CCITT V.32
INT mdmScFallback	1.3.6.1.4.1.429.1.6.6.1.1.18	INTEGER	read-write	Defines whether or not the modem will be allowed to change protocols it detects a significant change in the line characteristics. If the modem is unable to maintain transmission with the current modulation technique it would fall back to a lower speed and if the line then improved it would upshift to a higher speed. Default=enabled.
INT mdmScV32TerboModeEnable	1.3.6.1.4.1.429.1.6.6.1.1.19	INTEGER	read-write	Allows the V32 Terbo mode to be disabled/enabled.
INT mdmScV34ModeEnable	1.3.6.1.4.1.429.1.6.6.1.1.20	INTEGER	read-write	Allows V34 mode to be disabled/enabled.
INT mdmScVFCSymRate2400	1.3.6.1.4.1.429.1.6.6.1.1.21	INTEGER	read-write	Allows the 2400 symbol rate to be disabled/enabled on V.FC modems.
INT mdmScVFCSymRate2743	1.3.6.1.4.1.429.1.6.6.1.1.22	INTEGER	read-write	Allows the 2743 symbol rate to be disabled/enabled on V.FC modems.
INT mdmScVFCSymRate2800	1.3.6.1.4.1.429.1.6.6.1.1.23	INTEGER	read-write	Allows the 2800 symbol rate to be disabled/enabled on V.FC modems.
INT mdmScVFCSymRate3000	1.3.6.1.4.1.429.1.6.6.1.1.24	INTEGER	read-write	Allows the 3000 symbol rate to be disabled/enabled on V.FC modems.
INT mdmScVFCSymRate3200	1.3.6.1.4.1.429.1.6.6.1.1.25	INTEGER	read-write	Allows the 3200 symbol rate to be disabled/enabled on V.FC modems.
INT mdmScVFCSymRate3429	1.3.6.1.4.1.429.1.6.6.1.1.26	INTEGER	read-write	Allows the 3429 symbol rate to be disabled/enabled on V.FC modems.
INT mdmScVFC8S2DMapping	1.3.6.1.4.1.429.1.6.6.1.1.27	INTEGER	read-write	Allows the 8S-2D mapping to be disabled/enabled on V.FC modems.
INT mdmScVFC16S4DMapping	1.3.6.1.4.1.429.1.6.6.1.1.28	INTEGER	read-write	Allows the 16S-4D mapping to be disabled/enabled on V.FC modems.
INT mdmScVFC32S2DMapping	1.3.6.1.4.1.429.1.6.6.1.1.29	INTEGER	read-write	Allows the 32S-2D mapping to be disabled/enabled on V.FC modems.
INT mdmScVFC64S4DMapping	1.3.6.1.4.1.429.1.6.6.1.1.30	INTEGER	read-write	Allows the 64S-4D mapping to be disabled/enabled on V.FC modems.
INT mdmScVFCNonLinearCoding	1.3.6.1.4.1.429.1.6.6.1.1.31	INTEGER	read-write	Allows the non-linear coding to be disabled/enabled on V.FC modems.
INT mdmScVFCTxLevelDeviation	1.3.6.1.4.1.429.1.6.6.1.1.32	INTEGER	read-write	Allows the TX level deviation to be disabled/enabled on V.FC modems.
INT mdmScVFCPreEmphasis	1.3.6.1.4.1.429.1.6.6.1.1.33	INTEGER	read-write	Allows the pre-emphasis to be disabled/enabled on V.FC modems.
INT mdmScVFCPreCoding	1.3.6.1.4.1.429.1.6.6.1.1.34	INTEGER	read-write	Allows the precoding to be disabled/enabled on V.FC modems.
INT mdmScVFCShaping	1.3.6.1.4.1.429.1.6.6.1.1.35	INTEGER	read-write	Allows the shaping to be disabled/enabled on V.FC modems.
INT mdmScVFCModeEnable	1.3.6.1.4.1.429.1.6.6.1.1.36	INTEGER	read-write	Allows to disable/enable V.FC mode in order to troubleshoot a connection.
INT mdmScV8	1.3.6.1.4.1.429.1.6.6.1.1.37	INTEGER	read-write	Allow V8 mode to be disabled/enabled
INT mdmSCV8CallIndicator	1.3.6.1.4.1.429.1.6.6.1.1.38	INTEGER	read-write	Allow V.8. call indicater to be disabled/enabled.
INT mdmScV34pModeEnable	1.3.6.1.4.1.429.1.6.6.1.1.39	INTEGER	read-write	Allows V34 plus modulation mode to be disabled. (default=0/enabled)
INT mdmSc300	1.3.6.1.4.1.429.1.6.6.1.1.40	INTEGER	read-write	Restrict 300 baud negotiations. Register S48.0 Default is disable (0) restriction.
INT mdmSc1200	1.3.6.1.4.1.429.1.6.6.1.1.41	INTEGER	read-write	Restrict 1200 baud negotiations. Register S48.1 Default is disable (0) restriction.
INT mdmSc2400	1.3.6.1.4.1.429.1.6.6.1.1.42	INTEGER	read-write	Restrict 2400 baud negotiations. Register S48.2 Default is disable (0) restriction.
INT mdmScHighSpeed	1.3.6.1.4.1.429.1.6.6.1.1.43	INTEGER	read-write	Restrict highspeed baud negotiations. Register S48.3 Default is disable (0) restriction.
INT mdmScSelectiveReject	1.3.6.1.4.1.429.1.6.6.1.1.44	INTEGER	read-write	Selective Reject register S51.6 is a function of the V.42/LAPM protocol. The default is enable (1)
INT mdmScPhExclusionDel	1.3.6.1.4.1.429.1.6.6.1.1.45	INTEGER	read-write	Enable/disable phone extension delay S51.7. Default is enable
INT mdmScLinkRateAmpU	1.3.6.1.4.1.429.1.6.6.1.1.46	INTEGER	read-write	Minimum high-speed direction link speed Default=variable.
INT mdmScLowerSpeedMin	1.3.6.1.4.1.429.1.6.6.1.1.47	INTEGER	read-write	Lower speed direction minimum Default=1.
INT mdmScLowerSpeedMax	1.3.6.1.4.1.429.1.6.6.1.1.48	INTEGER	read-write	Lower speed direction maximum Default=1.
INT mdmScX2Client	1.3.6.1.4.1.429.1.6.6.1.1.49	INTEGER	read-write	X2 Client Mode Disable Default=enabled.
INT mdmScX2Server	1.3.6.1.4.1.429.1.6.6.1.1.50	INTEGER	read-write	X2 Server Mode Disable Default=enabled.
INT mdmScX2Symmetric	1.3.6.1.4.1.429.1.6.6.1.1.51	INTEGER	read-write	X2 Symmetric Mode Disable Default=enable.
INT mdmScX2HighPowerConst	1.3.6.1.4.1.429.1.6.6.1.1.52	INTEGER	read-write	This object is used to enable/disable the X2 high-power constellation. This object is only valid in countries, where it is legal. It corresponds to S Register 76.7 Default = Disable(1).
INT mdmScPiafs	1.3.6.1.4.1.429.1.6.6.1.1.53	INTEGER	read-write	This object is used to enable/disable PIAFS protocol. It corresponds to S Register 72.4 Default = enable(1).
INT mdmScPiafsV42bis	1.3.6.1.4.1.429.1.6.6.1.1.54	INTEGER	read-write	This object is used to enable/disable PIAFS V42bis compression protocol. It corresponds to S Register 72.5. Default = enable(1).
INT mdmScTxPwrLvl	1.3.6.1.4.1.429.1.6.6.1.1.55	INTEGER	read-write	This object configures the power level. It applies to S-register S82.
INT mdmScTxPwrLvlApplied	1.3.6.1.4.1.429.1.6.6.1.1.56	INTEGER	read-write	This object configures where the power level is applied. It applies to S-register S81.0.
INT mdmScX2Version2	1.3.6.1.4.1.429.1.6.6.1.1.57	INTEGER	read-write	This object is the x2 Version 2 Modulation. It applies to S-register S81.1
INT mdmScV34Fallback	1.3.6.1.4.1.429.1.6.6.1.1.58	INTEGER	read-write	This object is the x2 fallback to v34. It applies to S-register S76.3
INT mdmScV90Analogue	1.3.6.1.4.1.429.1.6.6.1.1.59	INTEGER	read-write	This object controls the enable/disable of the V.90 client modulation.Default=Enable(1).
INT mdmScV90Digital	1.3.6.1.4.1.429.1.6.6.1.1.60	INTEGER	read-write	This object controls the enable/disable of the V.90 server modulation.Default=Enable(1).
INT mdmScV90AllDigital	1.3.6.1.4.1.429.1.6.6.1.1.61	INTEGER	read-write	This object controls the enable/disable of the V.90 symmetric modulation. Default=Enable(1).
mdmCc	1.3.6.1.4.1.429.1.6.7
mdmCcTable	1.3.6.1.4.1.429.1.6.7.1		not-accessible	A table containing the call control parameters for each modem in the chassis.
mdmCcEntry	1.3.6.1.4.1.429.1.6.7.1.1		not-accessible	Call control parameters for a modem. These define the sequence of operation related to how a call is negotiated.
INT mdmCcIndex	1.3.6.1.4.1.429.1.6.7.1.1.1	INTEGER	read-only	The index which uniquely identifies the modem to which this entry is applicable. The value corresponds to the value of the index to the entity table in the chassis MIB that corresponds to the same modem.
INT mdmCcDialDelay	1.3.6.1.4.1.429.1.6.7.1.1.2	INTEGER	read-write	Defines the number of seconds the modem waits between going off hook and begining to dial. Ignored when result code options 2,4,6,or 7 are active. Default=2.
INT mdmCcWaitForCarrier	1.3.6.1.4.1.429.1.6.7.1.1.3	INTEGER	read-write	Defines the number of seconds the modem will wait for a carrier signal after dialing. Default=60.
INT mdmCcInactivityTimer	1.3.6.1.4.1.429.1.6.7.1.1.4	INTEGER	read-write	Sets the duration (in seconds) that the modem will maintain a connection when there is no activity on the phone line. The feature is disabled when set to 0. Default=0.
INT mdmCcAutoDialOnDtrEna	1.3.6.1.4.1.429.1.6.7.1.1.5	INTEGER	read-write	When enabled the modem will dial the number present in mdmCCPhoneString0 when the DTR signal transitions from low to high. Default=disable(1).
INT mdmCcAutoDialOnPwrUpEna	1.3.6.1.4.1.429.1.6.7.1.1.6	INTEGER	read-write	When enabled, the modem will dial the number present in mdmCcPhoneString0 on power up or after a reset. Default=disable(1).
INT mdmCcGhostPortLockEna	1.3.6.1.4.1.429.1.6.7.1.1.7	INTEGER	read-write	When enabled, the modem requires that DTR go low before it will accept another call. The modem also implements a Fast Connect mode where CD is asserted before the link negotiation is complete. Default=disable(1).
INT mdmCcQuietResultCodes	1.3.6.1.4.1.429.1.6.7.1.1.8	INTEGER	read-write	Determines whether or not the modem transmits result codes to the DTE. Default=noResult(2).
INT mdmCcResponseMode	1.3.6.1.4.1.429.1.6.7.1.1.9	INTEGER	read-write	Determines whether the modem transmits result codes in the verbal or numeric mode. Default=verbal(2).
INT mdmCcResultCodeOptions	1.3.6.1.4.1.429.1.6.7.1.1.10	INTEGER	read-write	Defines one of eight result code subsets and also defines indirectly how the modem reacts to dial tone etc. Equates to the modem's X register Default=1.
INT mdmCcArqResultCodeMode	1.3.6.1.4.1.429.1.6.7.1.1.11	INTEGER	read-write	Defines whether or not the ARQ result codes are sent to the DTE on connection(if result codes are enabled). Default=arqResultsEnabled(2).
INT mdmCcEscCodeRsp	1.3.6.1.4.1.429.1.6.7.1.1.12	INTEGER	read-write	Defines the action of the modem in response to the escape code(+++). The default value is determined by the state of Dip switch 2-3 on power up.
INT mdmCcAtRecognition	1.3.6.1.4.1.429.1.6.7.1.1.13	INTEGER	read-write	Determines which, if any, AT commands the modem will recognize or accept from the DTE. Default=ignore(1).
INT mdmCcMgmtSysMsgDis	1.3.6.1.4.1.429.1.6.7.1.1.14	INTEGER	read-write	Determines if the modem is to send special result codes, triggered by user conflicts with the management system, to the DTE. Default=enable(1).
INT mdmCcV32ToneDuration	1.3.6.1.4.1.429.1.6.7.1.1.15	INTEGER	read-write	Specifies the duration (in 10ths of a second) that the modem transmits the 3000/600 Hz answer tones for V.32 handshaking. A setting of 0 eliminates these tones and will result in faster connect times for V.21 and V.23 calls. Default=8.
INT mdmCcAutoAnswer	1.3.6.1.4.1.429.1.6.7.1.1.17	INTEGER	read-write	Determines the number of rings that the modem will answer calls on. When set to 0 the modem can only originate calls. Default=1.
INT mdmCcAnswerInOrigMode	1.3.6.1.4.1.429.1.6.7.1.1.18	INTEGER	read-write	When enabled the modem will answer calls using the sequence normaly used by the originating modem. Default=disable(1).
INT mdmCcArqBufWait	1.3.6.1.4.1.429.1.6.7.1.1.19	INTEGER	read-write	Sets the duration (in seconds) that the modem waits on an ARQ call before clearing the transmit buffer and dropping carrier after DTR drops. This is to allow time for the remote modem to acknowledge receipt of all transmitted data. Default=0.
STR mdmCcPhoneString0	1.3.6.1.4.1.429.1.6.7.1.1.20	DisplayString	read-write	Phone number stored in modem's non volitile memory. Useful in providing quick access to frequently called numbers. In addition mdmCcPhoneString0 is used for the dial on power up and dial on DTR options.
STR mdmCcPhoneString1	1.3.6.1.4.1.429.1.6.7.1.1.21	DisplayString	read-write	Phone number stored in the modem's non volitile memory, useful for providing quick access to frequently called numbers.
STR mdmCcPhoneString2	1.3.6.1.4.1.429.1.6.7.1.1.22	DisplayString	read-write	Phone number stored in the modem's non volitile memory, useful in providing quick access to frequently called numbers.
STR mdmCcPhoneString3	1.3.6.1.4.1.429.1.6.7.1.1.23	DisplayString	read-write	Phone number stored in the modem's non volitile memory, useful in providing quick access to frequently called numbers.
INT mdmCcErrorCntlMode	1.3.6.1.4.1.429.1.6.7.1.1.24	INTEGER	read-write	Defines if the modem is operating in synchronous or asynchronous mode and how it responds relative to negotiation of error control on asynchronous connections. When set to the default, normalArq(3), the modem attempts to connect with error control but if unable to negotiate it connects anyway. When set to none(1), async connections do not attempt to use error control. When set to arqOnly(4), the modem will hang up if unable to negotiate error contol. When set to syncMode(2), the modem will not connect asynchronously.
INT mdmCcMiMic	1.3.6.1.4.1.429.1.6.7.1.1.25	INTEGER	read-write	Specifies whether the modem will recognize MI/MIC closure as the mechanism for detecting incomming calls. Default=disable(1).
INT mdmCcMnpWith1200	1.3.6.1.4.1.429.1.6.7.1.1.26	INTEGER	read-write	Determines if the modem will include MNP/V42 negotiation on 1200 bps connections. Default=enable(1).
INT mdmCcMnpWith2400	1.3.6.1.4.1.429.1.6.7.1.1.27	INTEGER	read-write	Determines if the modem will include MNP/V43 negotiation on 2400 bps calls. default=enable(1).
INT mdmCcMnpWithV32	1.3.6.1.4.1.429.1.6.7.1.1.28	INTEGER	read-write	Determines if the modem will include MNP/V42 negotiation on V.32 connections. Default=enable(1).
INT mdmCcMnpTimeout	1.3.6.1.4.1.429.1.6.7.1.1.29	INTEGER	read-write	Specifies the MNP/V42 link request timeout for negotiation of 1200 and 2400 bps calls. Default=5.
INT mdmCcV21V23FallBackTimer	1.3.6.1.4.1.429.1.6.7.1.1.30	INTEGER	read-write	V21/V23 fallback timer, 1/10 sec. NVRAM S Register S29. Default=20
INT mdmCcAddnlAnswToneDur	1.3.6.1.4.1.429.1.6.7.1.1.31	INTEGER	read-write	Additional answer tone duration, 1/10 sec. NVRAM S Register S49. Default=16.
INT mdmCcBillingDelayPeriod	1.3.6.1.4.1.429.1.6.7.1.1.32	INTEGER	read-write	Billing Delay Period. 1/50 sec. NVRAM S Register S50. Default=100.
STR mdmCcCarrierAccessCode1	1.3.6.1.4.1.429.1.6.7.1.1.33	DisplayString	read-write	The DNIS Carrier Access Code (CAC) Number. This is a string which contains a number from 1 to 10 digits (e.g. 9501755). This is the 1st of 3 CACs.
STR mdmCcCarrierAccessCode2	1.3.6.1.4.1.429.1.6.7.1.1.34	DisplayString	read-write	The DNIS Carrier Access Code (CAC) Number. This is a string which contains a number from 1 to 10 digits. This is the 2nd of 3 CACs.
STR mdmCcCarrierAccessCode3	1.3.6.1.4.1.429.1.6.7.1.1.35	DisplayString	read-write	The DNIS Carrier Access Code (CAC) Number. This is a string which contains a number from 1 to 10 digits. This is the 3rd of 3 CACs.
STR mdmCcCallingInitStr1	1.3.6.1.4.1.429.1.6.7.1.1.36	DisplayString	read-write	This is the Carrier Access Code (CAC) initialization string. This string is a configuration string of 1 to 30 characters (e.g. &F, &F&B1&R1, etc.) This string does NOT include the AT attention prefix. This is the 1st of 4 CAC init strings.
STR mdmCcCallingInitStr2	1.3.6.1.4.1.429.1.6.7.1.1.37	DisplayString	read-write	This is the Carrier Access Code (CAC) initialization string. This string is 1 to 30 characters. It does NOT include the AT attention prefix. It is the 2nd of 4 CAC init strings.
STR mdmCcCallingInitStr3	1.3.6.1.4.1.429.1.6.7.1.1.38	DisplayString	read-write	This is the Carrier Access Code (CAC) initialization string. This is a string of 1 to 30 characters. It does NOT include the AT attention prefix. This is the 3rd of 4 CAC init strings.
STR mdmCcCallingInitStr4	1.3.6.1.4.1.429.1.6.7.1.1.39	DisplayString	read-write	This is the Carrier Access Code (CAC) initialization string. This is a string of 1 to 30 characters. It does NOT include the AT attention prefix. This is the 4th of 4 CAC init strings.
INT mdmCcDataFaxMode	1.3.6.1.4.1.429.1.6.7.1.1.40	INTEGER	read-write	Gives the current Data/FAX mode of the modem.
INT mdmCcT1CallSetupProc	1.3.6.1.4.1.429.1.6.7.1.1.41	INTEGER	read-write	Determines T1 call setup procedures used. Choices are 'normal' or 'none'. None assumes a dedicated (leased) DS0 assigned to the modem. Default=normalSetup(1).
INT mdmCcT1DialToneType	1.3.6.1.4.1.429.1.6.7.1.1.42	INTEGER	read-write	Determines if MF or DTMF tones are used for T1 signaling. Default = mfTones(1).
INT mdmCcT1KpStMfTones	1.3.6.1.4.1.429.1.6.7.1.1.43	INTEGER	read-write	Determines the usage of KP and ST MF tone encapsulation of the dial sequence. Default=enable(1).
INT mdmCcT1CallInitStrUse	1.3.6.1.4.1.429.1.6.7.1.1.44	INTEGER	read-write	Determines if calling init strings are used or not. Default=enable(1).
INT mdmCcT1CallInitStrBase	1.3.6.1.4.1.429.1.6.7.1.1.45	INTEGER	read-write	Determines if the calling init strings are based upon DNIS or ANI. Default=dnisBase(1).
INT mdmCcIntBlackListDis	1.3.6.1.4.1.429.1.6.7.1.1.46	INTEGER	read-write	Disable BlackList restriction in the international modems. Default=0 (enable) s40.1 reg
INT mdmCcOffHookRestrict	1.3.6.1.4.1.429.1.6.7.1.1.47	INTEGER	read-write	Disable off-hook restriction in the international modems. Default=0 (enable) S40.2 reg
INT mdmCcT1DialInAniDig	1.3.6.1.4.1.429.1.6.7.1.1.48	INTEGER	read-write	Sets the number of ANI digits allowed in incoming calls. Default = 0.
INT mdmCcT1DialInDnisDig	1.3.6.1.4.1.429.1.6.7.1.1.49	INTEGER	read-write	Sets the number of DNIS/DID digits allowed in incoming calls. Default = 0.
INT mdmCcNoPbNoConnEna	1.3.6.1.4.1.429.1.6.7.1.1.50	INTEGER	read-write	Sets if to answer a call when there is no Packet Bus link. Normal is the Default =0
INT mdmCcIdleDiscPatt	1.3.6.1.4.1.429.1.6.7.1.1.51	INTEGER	read-write	Idle disconnect pattern sent to the T1 NAC. Normal values: USA = 1, international = 84. Default = 1. Configure the T1 identically. Consult the help screen, user manual or US Robotics before changing. Modem register S71.
INT mdmCcMnp10	1.3.6.1.4.1.429.1.6.7.1.1.52	INTEGER	read-write	S61.4 register disable/enable MNP10 originate mode.
INT mdmCcMnp10Ec	1.3.6.1.4.1.429.1.6.7.1.1.53	INTEGER	read-write	S61.5 register disable/enable MNP10EC originate mode.
INT mdmCcAtzPbHandling	1.3.6.1.4.1.429.1.6.7.1.1.54	INTEGER	read-write	ATZ handling over Packet Bus. S72 REG
INT mdmCcDefltPRISlot	1.3.6.1.4.1.429.1.6.7.1.1.55	INTEGER	read-write	Default dialout PRI slot. Default = 1
INT mdmCcExtDTMFToneSupport	1.3.6.1.4.1.429.1.6.7.1.1.56	INTEGER	read-write	Enable/Disable DTMF extended support. Default = disable
INT mdmCcDataOverVoice	1.3.6.1.4.1.429.1.6.7.1.1.57	INTEGER	read-write	Data Over Voice support originate S68.1.
INT mdmCc2100AnswerTone	1.3.6.1.4.1.429.1.6.7.1.1.58	INTEGER	read-write	Data Over Voice support answer S68.2.
INT mdmCcEnableV120v42Bis	1.3.6.1.4.1.429.1.6.7.1.1.59	INTEGER	read-write	V.42bis Compression over V.120. S67.4
INT mdmCcHdlcLicIe	1.3.6.1.4.1.429.1.6.7.1.1.60	INTEGER	read-write	This object is to Enable\Disable LIC IE message for HDLC protocols. S Register S68.3
INT mdmCcDtmfTerminationTone	1.3.6.1.4.1.429.1.6.7.1.1.61	INTEGER	read-write	This object is to set the DTMF Termination Tone.
INT mdmCcAfaxMaxRateSrvOpt20	1.3.6.1.4.1.429.1.6.7.1.1.62	INTEGER	read-write	This object is used to limit the maximum rate for an Analog Fax Connection. Service option 20. Upper nibble of the S94 register.
INT mdmCcAfaxMaxRateSrvOpt21	1.3.6.1.4.1.429.1.6.7.1.1.63	INTEGER	read-write	This object is used to limit the maximum rate for an Analog Fax Connection. Service option 21. Lower nibble of S94 register.
mdmEc	1.3.6.1.4.1.429.1.6.8
mdmEcTable	1.3.6.1.4.1.429.1.6.8.1		not-accessible	A table of Error Control Parameters for each modem in this system, the quantity of entries is given by modemNumber.
mdmEcEntry	1.3.6.1.4.1.429.1.6.8.1.1		not-accessible	Configurable objects which define the modems error control operation.
INT mdmEcIndex	1.3.6.1.4.1.429.1.6.8.1.1.1	INTEGER	read-only	This object contains the unique value assigned to this modem in the chassis mib entity relation table and is used as the mechanism for correctly indexing into this table.
INT mdmEcMnp3Dis	1.3.6.1.4.1.429.1.6.8.1.1.2	INTEGER	read-write	Determines if the modem will negotiate for MNP level 3 error correction. Default=enable.
INT mdmEcMnp4Dis	1.3.6.1.4.1.429.1.6.8.1.1.3	INTEGER	read-write	Determines if the modem will negotiate for MNP level 4 error correction. Default=enable.
INT mdmEcMnpUnusual	1.3.6.1.4.1.429.1.6.8.1.1.4	INTEGER	read-write	Determines if the modem will attempt to negotiate for MNP operation used in some early 2400bps modems. Default=disable.
INT mdmEcV42MnpHandshake	1.3.6.1.4.1.429.1.6.8.1.1.5	INTEGER	read-write	Determines what types of error correction the modem will attempt to negotiate. When configured for the default, full V.42 and MNP, the modem first tries to connect with V42 error control and then with MNP error control. When set to disable either V42 or MNP the modem will only attempt to negotiate the enabled protocol. When set to disable the V42 detect phase, it is not included in the handshaking process. This allows for faster connections between V42 modems.
mdmCs	1.3.6.1.4.1.429.1.6.9
mdmCsTable	1.3.6.1.4.1.429.1.6.9.1		not-accessible	A table of modem status and call statistic parameters for each modem in the chassis.
mdmCsEntry	1.3.6.1.4.1.429.1.6.9.1.1		not-accessible	Objects that define the modem status and statistics specific to a the current connection when the modem is on line or to the last connection when the modem is idle.
INT mdmCsIndex	1.3.6.1.4.1.429.1.6.9.1.1.1	INTEGER	read-only	The index value which uniquely identifies the modem to which this entry is applicable. The value corresponds to the index of the same modem in the entity table of the chassis MIB.
INT mdmCsStatus	1.3.6.1.4.1.429.1.6.9.1.1.2	INTEGER	read-only	Current status of a modem including presence(idle), availability(disabled), and call progress states.
STR mdmCsLastNumberDialedOut	1.3.6.1.4.1.429.1.6.9.1.1.3	DisplayString	read-only	An ASCII string which represents the last phone number dialed by the modem.
STR mdmCsLastNumberDialedIn	1.3.6.1.4.1.429.1.6.9.1.1.4	DisplayString	read-only	An ASCII string representing the last number dialed in(if known). This is the 950-xxx (DNIS) number.
STR mdmCsLastCallingPartyNum	1.3.6.1.4.1.429.1.6.9.1.1.5	DisplayString	read-only	An ASCII string representing the current or last party that called this modem. Only known in ANI applications.
INT mdmCsOriginateAnswer	1.3.6.1.4.1.429.1.6.9.1.1.6	INTEGER	read-only	Defines whether the last or current call was originated or answered.
INT mdmCsRings	1.3.6.1.4.1.429.1.6.9.1.1.7	INTEGER	read-only	Defines the quantity of rings detected before the DTE answered with DTR on the last incomming call.
INT mdmCsDisconnectReason	1.3.6.1.4.1.429.1.6.9.1.1.8	INTEGER	read-only	Defines the reason that the last call was terminated.
INT mdmCsConnectFailReason	1.3.6.1.4.1.429.1.6.9.1.1.9	INTEGER	read-only	Defines the reason for failure if indeed the last call attempt failed.
INT mdmCsInitialTxLinkRate	1.3.6.1.4.1.429.1.6.9.1.1.10	INTEGER	read-only	The transmit speed at which the modem initialy connected on it's last or current call.
INT mdmCsInitialRxLinkRate	1.3.6.1.4.1.429.1.6.9.1.1.11	INTEGER	read-only	The receive speed at which the modem initialy connected on it's previous or current call.
INT mdmCsFinalTxLinkRate	1.3.6.1.4.1.429.1.6.9.1.1.12	INTEGER	read-only	The current transmit link rate of a connection, or the last link rate of the last connection.
INT mdmCsFinalRxLinkRate	1.3.6.1.4.1.429.1.6.9.1.1.13	INTEGER	read-only	The current receive link rate of a connection, or the last link rate of the last connection.
INT mdmCsModulationType	1.3.6.1.4.1.429.1.6.9.1.1.14	INTEGER	read-only	Specifies the current/final modulation type of the current or last call. The value can be different from the object mdmCsInitModulationType only for X2/V.90 calls.
INT mdmCsSyncAsyncModeUsed	1.3.6.1.4.1.429.1.6.9.1.1.15	INTEGER	read-only	Defines whether the current or last call was synchronous or asynchronous.
INT mdmCsErrorControlType	1.3.6.1.4.1.429.1.6.9.1.1.16	INTEGER	read-only	Specifies the Error control settings in the current or last call. (short form)
INT mdmCsCompressionType	1.3.6.1.4.1.429.1.6.9.1.1.17	INTEGER	read-only	Specifies the data compression used in the current or last call. (short format)
INT mdmCsEqualizationType	1.3.6.1.4.1.429.1.6.9.1.1.18	INTEGER	read-only	Specifies the equalization used in the current or last call.
INT mdmCsFallbackEnabled	1.3.6.1.4.1.429.1.6.9.1.1.19	INTEGER	read-only	Specifies whether line speed fallbacks were negotiated on the current or previous call.
INT mdmCsCharsSent	1.3.6.1.4.1.429.1.6.9.1.1.20	INTEGER	read-only	Specifies the number of characters sent on the current or previous call.
INT mdmCsCharsReceived	1.3.6.1.4.1.429.1.6.9.1.1.21	INTEGER	read-only	Specifies the number of characters received in the current or previous call.
INT mdmCsOctetsSent	1.3.6.1.4.1.429.1.6.9.1.1.22	INTEGER	read-only	Specifies the number of octets sent in the current or previous call.
INT mdmCsOctetsReceived	1.3.6.1.4.1.429.1.6.9.1.1.23	INTEGER	read-only	Specifies the number of octets received in the current or previous call.
INT mdmCsBlocksSent	1.3.6.1.4.1.429.1.6.9.1.1.24	INTEGER	read-only	Specifies the number of blocks sent in the current or previous call.
INT mdmCsBlocksReceived	1.3.6.1.4.1.429.1.6.9.1.1.25	INTEGER	read-only	Specifies the number of blocks received in the current or previous call.
INT mdmCsBlocksResent	1.3.6.1.4.1.429.1.6.9.1.1.26	INTEGER	read-only	Specifies the number of blocks the modem has had to retransmit due to block errors or timeouts in the current or previous call.
INT mdmCsRetrainsRequested	1.3.6.1.4.1.429.1.6.9.1.1.27	INTEGER	read-only	Specifies the number of retrains requested in the current or previous call.
INT mdmCsRetrainsGranted	1.3.6.1.4.1.429.1.6.9.1.1.28	INTEGER	read-only	Specifies the number of retrains granted in the current or previous call.
INT mdmCsLineReversalQty	1.3.6.1.4.1.429.1.6.9.1.1.29	INTEGER	read-only	Specifies the number of times the HST high and low speeds directions have been reversed in the current or previous call.
INT mdmCsCharsLost	1.3.6.1.4.1.429.1.6.9.1.1.30	INTEGER	read-only	Specifies the number of characters lost on the current or previous call. Not meaningful on synchronous calls.
INT mdmCsBackChannelRate	1.3.6.1.4.1.429.1.6.9.1.1.31	INTEGER	read-only	Specifies the negotiated HST back channel speed on the current or previous call.
INT mdmCsBlerQty	1.3.6.1.4.1.429.1.6.9.1.1.32	INTEGER	read-only	Specifies the number of block errors received on the link in the current or last call.
INT mdmCsLinkTimeoutQty	1.3.6.1.4.1.429.1.6.9.1.1.33	INTEGER	read-only	Specifies the number of link protocol timeouts on the current or previous call.
INT mdmCsFallbackQty	1.3.6.1.4.1.429.1.6.9.1.1.34	INTEGER	read-only	Specifies the quantity of link speed fallbacks that occured on the current or previous call.
INT mdmCsUpshiftQty	1.3.6.1.4.1.429.1.6.9.1.1.35	INTEGER	read-only	Specifies the number of link speed upshifts have occured in the current or previous call.
INT mdmCsLinkNakQty	1.3.6.1.4.1.429.1.6.9.1.1.36	INTEGER	read-only	Specifies the quantity of negative acknowledgements sent in response to errored blocks received on the link in the current or previous call.
INT mdmCsGainHitCount	1.3.6.1.4.1.429.1.6.9.1.1.37	INTEGER	read-only	The modem calculates the gain that is required to adjust the received signal to the ideal level. This defines the number of times that the gain was recalculated durring the current or previous call.
STR mdmCsSecurityUserName	1.3.6.1.4.1.429.1.6.9.1.1.38	DisplayString	read-only	The last dial security user that initiated the Call. This object is not saved to NVRAM.
STR mdmCsCallDuration	1.3.6.1.4.1.429.1.6.9.1.1.39	DisplayString	read-only	This is the length of the call in hh:mm:ss format. The maximum value reported will be 9999:59:59.
INT mdmCsCallRefNum	1.3.6.1.4.1.429.1.6.9.1.1.40	INTEGER	read-only	Call Reference Number
INT mdmCsPriCardSlot	1.3.6.1.4.1.429.1.6.9.1.1.41	INTEGER	read-only	Primary Card Slot
INT mdmCsTDMTimeSlot	1.3.6.1.4.1.429.1.6.9.1.1.42	INTEGER	read-only	Time Division Multipexing Time Slot
INT mdmCsPriCardSpanLine	1.3.6.1.4.1.429.1.6.9.1.1.43	INTEGER	read-only	Primary Card Span Line
INT mdmCsBChannelUsed	1.3.6.1.4.1.429.1.6.9.1.1.44	INTEGER	read-only	B Channel Used
INT mdmCsQCarrFreqTx	1.3.6.1.4.1.429.1.6.9.1.1.45	INTEGER	read-only	Transmit carrier value (Hz).
INT mdmCsQCarrFreqRx	1.3.6.1.4.1.429.1.6.9.1.1.46	INTEGER	read-only	Receive carrier value (Hz).
INT mdmCsQSymRateTx	1.3.6.1.4.1.429.1.6.9.1.1.47	INTEGER	read-only	Transmit symbol rate.
INT mdmCsQSymRateRx	1.3.6.1.4.1.429.1.6.9.1.1.48	INTEGER	read-only	Receive symbol rate.
INT mdmCsQTrellisTx	1.3.6.1.4.1.429.1.6.9.1.1.49	INTEGER	read-only	Transmit Trellis coding.
INT mdmCsQTrellisRx	1.3.6.1.4.1.429.1.6.9.1.1.50	INTEGER	read-only	Receive Trellis coding.
INT mdmCsQNonLinCdTx	1.3.6.1.4.1.429.1.6.9.1.1.51	INTEGER	read-only	Status of transmit non-linear coding.
INT mdmCsQNonLinCdRx	1.3.6.1.4.1.429.1.6.9.1.1.52	INTEGER	read-only	Status of receive non-linear coding.
INT mdmCsQPrecodingTx	1.3.6.1.4.1.429.1.6.9.1.1.53	INTEGER	read-only	Status of transmit precoding.
INT mdmCsQPrecodingRx	1.3.6.1.4.1.429.1.6.9.1.1.54	INTEGER	read-only	Status of receive precoding.
INT mdmCsQShapingTx	1.3.6.1.4.1.429.1.6.9.1.1.55	INTEGER	read-only	Status of transmit shaping.
INT mdmCsQShapingRx	1.3.6.1.4.1.429.1.6.9.1.1.56	INTEGER	read-only	Status of receive shaping.
INT mdmCsQPreemphTx	1.3.6.1.4.1.429.1.6.9.1.1.57	INTEGER	read-only	Transmit pre-emphasis (-dBm).
INT mdmCsQPreemphRx	1.3.6.1.4.1.429.1.6.9.1.1.58	INTEGER	read-only	Receive pre-emphasis (-dBm).
INT mdmCsQRxLevel	1.3.6.1.4.1.429.1.6.9.1.1.59	INTEGER	read-only	Receive level (X 10) (-dBm).
INT mdmCsQTxLevel	1.3.6.1.4.1.429.1.6.9.1.1.60	INTEGER	read-only	Transmit level (X 10) (-dBm).
INT mdmCsQSNR	1.3.6.1.4.1.429.1.6.9.1.1.61	INTEGER	read-only	Signal to noise (x 10) (dB).
INT mdmCsQNearEcho	1.3.6.1.4.1.429.1.6.9.1.1.62	INTEGER	read-only	Near echo (x 10) (dB).
INT mdmCsQFarEcho	1.3.6.1.4.1.429.1.6.9.1.1.63	INTEGER	read-only	Far echo (x 10) (dB).
INT mdmCsQRndTripDly	1.3.6.1.4.1.429.1.6.9.1.1.64	INTEGER	read-only	Round trip delay (msec).
INT mdmCsQPacketSizeCurr	1.3.6.1.4.1.429.1.6.9.1.1.65	INTEGER	read-only	Current packet size (bytes).
INT mdmCsQPacketSizeLow	1.3.6.1.4.1.429.1.6.9.1.1.66	INTEGER	read-only	Min. packet size (bytes).
INT mdmCsQPacketSizeHigh	1.3.6.1.4.1.429.1.6.9.1.1.67	INTEGER	read-only	Max. packet size (bytes).
INT mdmCsQCellTxLevelCurr	1.3.6.1.4.1.429.1.6.9.1.1.68	INTEGER	read-only	Current Tx level cellular (x 10)(-dBm).
INT mdmCsQCellTxLevelLow	1.3.6.1.4.1.429.1.6.9.1.1.69	INTEGER	read-only	Min. Tx level cellular (x 10)(-dBm).
INT mdmCsQCellTxLevelHigh	1.3.6.1.4.1.429.1.6.9.1.1.70	INTEGER	read-only	Max. Tx level cellular (x 10)(-dBm).
INT mdmCsQSNRLevelCurr	1.3.6.1.4.1.429.1.6.9.1.1.71	INTEGER	read-only	Current SNR level cellular (x 10) (-dBm).
INT mdmCsQSNRLevelLow	1.3.6.1.4.1.429.1.6.9.1.1.72	INTEGER	read-only	Min. SNR level cellular (x 10) (-dBm).
INT mdmCsQSNRLevelHigh	1.3.6.1.4.1.429.1.6.9.1.1.73	INTEGER	read-only	Max. SNR level cellular (x 10) (-dBm).
INT mdmCsQCellularProt	1.3.6.1.4.1.429.1.6.9.1.1.74	INTEGER	read-only	Current cellular protocol.
OCT mdmCsFreqProbeData	1.3.6.1.4.1.429.1.6.9.1.1.75	OCTET STRING	read-only	Probe frequency.
OCT mdmCsLevelProbeData	1.3.6.1.4.1.429.1.6.9.1.1.76	OCTET STRING	read-only	Probe level.
INT mdmCsQTimingOffset	1.3.6.1.4.1.429.1.6.9.1.1.77	INTEGER	read-only	Timing Offset in parts per million.
INT mdmCsQCarrierOffset	1.3.6.1.4.1.429.1.6.9.1.1.78	INTEGER	read-only	Carrier Offset in Hertz.
INT mdmCsQCoding	1.3.6.1.4.1.429.1.6.9.1.1.80	INTEGER	read-only	PCM Coding mu/A law Default=mulaw.
OCT mdmCsTrainingInfo	1.3.6.1.4.1.429.1.6.9.1.1.81	OCTET STRING	read-only	Training Information
OCT mdmCsX2signature	1.3.6.1.4.1.429.1.6.9.1.1.82	OCTET STRING	read-only	X2 diagnostics information from modem in hex.
INT mdmCsX2Status	1.3.6.1.4.1.429.1.6.9.1.1.83	INTEGER	read-only	x2 status of modem.
INT mdmCsCallType	1.3.6.1.4.1.429.1.6.9.1.1.84	INTEGER	read-only	Call type information.
INT mdmCsCallStartTime	1.3.6.1.4.1.429.1.6.9.1.1.85	INTEGER	read-only	Call started time in GMT format.
INT mdmCsCallEndTime	1.3.6.1.4.1.429.1.6.9.1.1.86	INTEGER	read-only	Call Ended time in GMT format.
INT mdmCsDigitalPadAttenuated	1.3.6.1.4.1.429.1.6.9.1.1.87	INTEGER	read-only	Attenuation of the digital pad in tenths of DB.
INT mdmCsInitModulationType	1.3.6.1.4.1.429.1.6.9.1.1.88	INTEGER	read-only	Specifies the modulation type of the current or last call. The value can be different from the object mdmCsModulationType only for X2/V.90 calls.
INT mdmCsRxMinSpeed	1.3.6.1.4.1.429.1.6.9.1.1.89	INTEGER	read-only	Current/Last Session MIN Rx Speed.
INT mdmCsRxMaxSpeed	1.3.6.1.4.1.429.1.6.9.1.1.90	INTEGER	read-only	Current/Last Session MAX Rx Speed.
INT mdmCsTxMinSpeed	1.3.6.1.4.1.429.1.6.9.1.1.91	INTEGER	read-only	Current/Last Session MIN Tx Speed.
INT mdmCsTxMaxSpeed	1.3.6.1.4.1.429.1.6.9.1.1.92	INTEGER	read-only	Current/Last Session MAX Tx Speed.
OCT mdmCsCollectedDTMFDigits	1.3.6.1.4.1.429.1.6.9.1.1.93	OCTET STRING	read-only	This object is an ASCII array of the DTMF digits collected from the client.
mdmEv	1.3.6.1.4.1.429.1.6.10
mdmEvTable	1.3.6.1.4.1.429.1.6.10.1		not-accessible	A list of modem events.
mdmEvEntry	1.3.6.1.4.1.429.1.6.10.1.1		not-accessible	Modem events that can be managed.
INT mdmEvIndex	1.3.6.1.4.1.429.1.6.10.1.1.1	INTEGER	read-only	Index into event table.
CTR mdmEvWatchdogTimouts	1.3.6.1.4.1.429.1.6.10.1.1.2	Counter	read-only	Quantity of times that a watchdog timeout has been detected for this modem.
CTR mdmEvDteIdleTimouts	1.3.6.1.4.1.429.1.6.10.1.1.3	Counter	read-only	The number of times that the modem has had no DTE activity for the time specified by mdmEtDteIdleThresh.
CTR mdmEvInConnectEstabs	1.3.6.1.4.1.429.1.6.10.1.1.4	Counter	read-only	The number of times that the modem has reported a incomming connection established event.
CTR mdmEvOutConnectEstabs	1.3.6.1.4.1.429.1.6.10.1.1.5	Counter	read-only	The number of times that the modem has reported an outgoing connection established event.
CTR mdmEvInConnectTerms	1.3.6.1.4.1.429.1.6.10.1.1.6	Counter	read-only	The number of times the modem has reported an incomming connection terminated event.
CTR mdmEvOutConnectTerms	1.3.6.1.4.1.429.1.6.10.1.1.7	Counter	read-only	The number of times the modem has reported an outgoing connection termination event.
CTR mdmEvConnectAttemptFails	1.3.6.1.4.1.429.1.6.10.1.1.8	Counter	read-only	The number of times the modem has reported a connect attempt failure event. This does not include those connect attempt failures that are reported due to no dial tone and no loop current.
CTR mdmEvConnectTimouts	1.3.6.1.4.1.429.1.6.10.1.1.9	Counter	read-only	The number of times that the NMC has detected a call that has has a duration in excess of the threshold defined in mdmEtConnectThresh.
CTR mdmEvMgmtBusFailures	1.3.6.1.4.1.429.1.6.10.1.1.10	Counter	read-only	The number of times the NMC has been unable to get a response from the modem to requests on the management bus.
CTR mdmEvResetByDtes	1.3.6.1.4.1.429.1.6.10.1.1.11	Counter	read-only	The number of times that the modem has been reset by the DTE via the ATZ command or by DTR drop.
CTR mdmEvDtrFalses	1.3.6.1.4.1.429.1.6.10.1.1.12	Counter	read-only	The number of times the modem has reported DTR False events. The DTR false event timeout is based on mdmEtDtrFalseThresh.
CTR mdmEvDtrTrues	1.3.6.1.4.1.429.1.6.10.1.1.13	Counter	read-only	The number of times the modem has reported DTR True events. The modem reports these events to the NMC based on the value of mdmEtDtrTrueTresh.
CTR mdmEvNoTones	1.3.6.1.4.1.429.1.6.10.1.1.14	Counter	read-only	The number of times the modem reported no tones.
CTR mdmEvNoLoops	1.3.6.1.4.1.429.1.6.10.1.1.15	Counter	read-only	The number of times the modem reported no loop current events.
CTR mdmEvBlers	1.3.6.1.4.1.429.1.6.10.1.1.16	Counter	read-only	The number of times the modem reported BLERs.
CTR mdmEvFallBacks	1.3.6.1.4.1.429.1.6.10.1.1.17	Counter	read-only	The number of times the modem reported fall backs.
CTR mdmEvInConnectTime	1.3.6.1.4.1.429.1.6.10.1.1.18	Counter	read-only	Cumulative counter for inbound call connect time.
CTR mdmEvInTotalBytesRx	1.3.6.1.4.1.429.1.6.10.1.1.19	Counter	read-only	Cumulative counter for number of bytes received on inbound calls.
CTR mdmEvInTotalBytesTx	1.3.6.1.4.1.429.1.6.10.1.1.20	Counter	read-only	Cumulative counter for number of bytes transmitted on inbound calls.
CTR mdmEvOutConnectTime	1.3.6.1.4.1.429.1.6.10.1.1.21	Counter	read-only	Cumulative counter for outbound call connect time.
CTR mdmEvOutTotalBytesRx	1.3.6.1.4.1.429.1.6.10.1.1.22	Counter	read-only	Cumulative counter for number of bytes received on outbound calls.
CTR mdmEvOutTotalBytesTx	1.3.6.1.4.1.429.1.6.10.1.1.23	Counter	read-only	Cumulative counter for number of bytes transmitted on outbound calls.
CTR mdmEvInConnAttemptFails	1.3.6.1.4.1.429.1.6.10.1.1.24	Counter	read-only	The number of times the modem has reported a inbound connect attempt failure event. This does not include those connect attempt failues that are reported due to no dial time and no loop current.
CTR mdmEvOutConnAttemptFails	1.3.6.1.4.1.429.1.6.10.1.1.25	Counter	read-only	The number of times the modem has reported a outbound connect attempt failure event. This does not include those connect attempt failures that are reported due to no dial tone and no loop current.
mdmEt	1.3.6.1.4.1.429.1.6.11
mdmEtTable	1.3.6.1.4.1.429.1.6.11.1		not-accessible	Table of event thresholds used for setting up the modem to report events that can in turn be monitored by RMON.
mdmEtEntry	1.3.6.1.4.1.429.1.6.11.1.1		not-accessible	Event Thresholds that are used by the modem and the NMC to qualify certain events.
INT mdmEtIndex	1.3.6.1.4.1.429.1.6.11.1.1.1	INTEGER	read-only	Index into table used to identify the the specific modem, contians the unique value from the chassis mib entity table.
INT mdmEtDteIdleThresh	1.3.6.1.4.1.429.1.6.11.1.1.2	INTEGER	read-write	Defines the length of time for the modem to wait before reporting a 'DTE transmit data idle' event. (There must be no activity on the DTE transmit line for the specified quantity of minutes.
INT mdmEtDtrFalseThresh	1.3.6.1.4.1.429.1.6.11.1.1.3	INTEGER	read-write	Defines the quantity of seconds that will be used by the modem to qualify a 'DTR False' event.
INT mdmEtDtrTrueThresh	1.3.6.1.4.1.429.1.6.11.1.1.4	INTEGER	read-write	Defines the quantity of seconds that the modem will use to qualify a 'DTR True' event.
INT mdmEtConnTimeLimit	1.3.6.1.4.1.429.1.6.11.1.1.5	INTEGER	read-write	Defines the number of minutes that a call may be connected before triggering the 'connect timer limit' event. A value of zero for this limit means that no event is to be detected (ie. no time limit).
INT mdmEtBlerThresh	1.3.6.1.4.1.429.1.6.11.1.1.6	INTEGER	read-write	Defines the number of BLERs that will be used to qualify the 'BLER count at threshold' event for a given call.
INT mdmEtFallbackThresh	1.3.6.1.4.1.429.1.6.11.1.1.7	INTEGER	read-write	Defines the number of fallbacks at which the 'fallback count at threshold' event will be generated for a given call.
mdmCd	1.3.6.1.4.1.429.1.6.12
mdmCdTable	1.3.6.1.4.1.429.1.6.12.1		not-accessible	The command table contains an entry for each modem installed in a chassis. It provides a means for processing actions requested by the management console. The mechanism used is to set the command and get the result which will indicate the success of the request.
mdmCdEntry	1.3.6.1.4.1.429.1.6.12.1.1		not-accessible	Objects that are used to request that certain actions be taken by the modem itself or that the NMC take certain actions for the modem.
INT mdmCdIndex	1.3.6.1.4.1.429.1.6.12.1.1.1	INTEGER	read-only	The index value which uniquely identifies the modem to which this entry is applicable. The value corresponds to the index of the corresponding modem in the entity table of the chassis MIB.
OCT mdmCdMgtStationId	1.3.6.1.4.1.429.1.6.12.1.1.2	OCTET STRING	read-write	This object is a generic read-write variable that a Management Station (MS) can use to guarantee that the results from a given command are the results of a command issued by that specific MS. Each MS must SET a unique value to this object when doing commands and GET the value of this object together with uchasCmdReqId and uchasCmdResult to detect interference from other MSs.
INT mdmCdReqId	1.3.6.1.4.1.429.1.6.12.1.1.3	INTEGER	read-write	This object contains the value of the request-id field in the SNMP PDU which invoked the most recent command or test on this modem. If the request-id is unknown or undefined, this object contains the value zero.
INT mdmCdFunction	1.3.6.1.4.1.429.1.6.12.1.1.4	INTEGER	read-write	This object contains a value that describes the command that is being invoked.
INT mdmCdForce	1.3.6.1.4.1.429.1.6.12.1.1.5	INTEGER	read-write	In certain cases the modem may be in a state where certain commands could adversely affect connectiuons. In such cases, a command request with this object not present or set to noForce will result in a warning. If the operator elects to ignore such warnings, this object can be set to force in a subsequent request to cause the command to be carried out regardless of the potetialy hazzerdous effect.
OCT mdmCdParam	1.3.6.1.4.1.429.1.6.12.1.1.6	OCTET STRING	read-write	This object can contain parameters that are specific to the particualar command being issued.
INT mdmCdResult	1.3.6.1.4.1.429.1.6.12.1.1.7	INTEGER	read-only	This object contains the result of the most recently requested command or test, or the value none(1) if no commands have been requested since last reset.
INT mdmCdCode	1.3.6.1.4.1.429.1.6.12.1.1.8	INTEGER	read-only	The value of this object indicates a further description of what went wrong when a command fails.
mdmTe	1.3.6.1.4.1.429.1.6.13
mdmTeTable	1.3.6.1.4.1.429.1.6.13.1		not-accessible	A table containing an enable for each trap that a modem entity is capable of generating. Some of these events occur often and traps may flood the network if care is not taken to avoid such conditions. These traps should be enabled sparingly. (usually only when debugging a problem on a particular modem)
mdmTeEntry	1.3.6.1.4.1.429.1.6.13.1.1		not-accessible	There is one modem trap enable row for each modem entity in the NAS chassis.
INT mdmTeIndex	1.3.6.1.4.1.429.1.6.13.1.1.1	INTEGER	read-only	A unique index which identifies the modem for which these trap enables pertain. The index to the trap enable table matches the index of the corresponding modem in the entity table in the chassis MIB.
INT mdmTeInConnEstablished	1.3.6.1.4.1.429.1.6.13.1.1.2	INTEGER	read-write	Enables generation of an SNMP trap upon detection of an incoming connection establishment on the specified modem.
INT mdmTeOutConnEstablished	1.3.6.1.4.1.429.1.6.13.1.1.3	INTEGER	read-write	Enables generation of an SNMP trap upon detection of an outgoing connection establishment on the specified modem.
INT mdmTeInConnTerminated	1.3.6.1.4.1.429.1.6.13.1.1.4	INTEGER	read-write	Enables generation of an SNMP trap upon detection of an incoming connection termination on the specified modem.
INT mdmTeOutConnTerminated	1.3.6.1.4.1.429.1.6.13.1.1.5	INTEGER	read-write	Enables generation of an SNMP trap upon detection of an outgoing connection terminated on the specified modem.
INT mdmTeConnAttemptFailure	1.3.6.1.4.1.429.1.6.13.1.1.6	INTEGER	read-write	Enables generation of an SNMP trap upon detection of a connection attemp failure on the specified modem.
INT mdmTeConnLimitExpired	1.3.6.1.4.1.429.1.6.13.1.1.7	INTEGER	read-write	Enables generation of an SNMP trap upon detection of the expiration of the connection time limit on the specified modem.
INT mdmTeDteXmitDataIdle	1.3.6.1.4.1.429.1.6.13.1.1.8	INTEGER	read-write	Enables generation of an SNMP trap upon detection of DTE transmit data idle on the specified modem.
INT mdmTeDtrTrue	1.3.6.1.4.1.429.1.6.13.1.1.9	INTEGER	read-write	Enables generation of an SNMP trap upon detection of DTR going true on the specified modem.
INT mdmTeDtrFalse	1.3.6.1.4.1.429.1.6.13.1.1.10	INTEGER	read-write	Enables generation of an SNMP trap upon detection of DTR going false on the specified modem.
INT mdmTeBlerCountAtThresh	1.3.6.1.4.1.429.1.6.13.1.1.11	INTEGER	read-write	Enables generation of an SNMP trap upon detection of the BLER count at the specified threshold on the specified modem.
INT mdmTeFallbkCountAtThresh	1.3.6.1.4.1.429.1.6.13.1.1.12	INTEGER	read-write	Enables generation of an SNMP trap upon detection of the fallback count at the specified threshold on the specified modem.
INT mdmTeNoDialTone	1.3.6.1.4.1.429.1.6.13.1.1.13	INTEGER	read-write	Enables generation of an SNMP trap upon detection of no dial tone on the specified modem.
INT mdmTeNoLoopCurrent	1.3.6.1.4.1.429.1.6.13.1.1.14	INTEGER	read-write	Enables generation of an SNMP trap upon detection of no loop current on the specified modem.
INT mdmTeResetByDTE	1.3.6.1.4.1.429.1.6.13.1.1.15	INTEGER	read-write	Enables generation of an SNMP trap upon detection of reset by DTE on the specified modem.
INT mdmTeDialOutCallDur	1.3.6.1.4.1.429.1.6.13.1.1.16	INTEGER	read-write	Enables the dial out (from the NMC) call duration trap. Default = disable(2).
INT mdmTeDialInCallDur	1.3.6.1.4.1.429.1.6.13.1.1.17	INTEGER	read-write	Enables the dial in (to the NMC) call duration trap. Default = disable(2).
INT mdmTePbActive	1.3.6.1.4.1.429.1.6.13.1.1.18	INTEGER	read-write	Enables the Packet Bus Active. Default = disable(2).
INT mdmTePbLost	1.3.6.1.4.1.429.1.6.13.1.1.19	INTEGER	read-write	Enables the Packet Bus Lost trap. Default = disable(2).
INT mdmTeDteRingNoAns	1.3.6.1.4.1.429.1.6.13.1.1.20	INTEGER	read-write	Enables the Dte Ring No Answer trap. Default = disable(2).
INT mdmTePbClockLossEvent	1.3.6.1.4.1.429.1.6.13.1.1.21	INTEGER	read-write	This object is used to disable the ability for a NAC to report when the packet bus clock has been lost. Default = disableAll(2).
INT mdmTePbClockRestoreEvent	1.3.6.1.4.1.429.1.6.13.1.1.22	INTEGER	read-write	This object is used to disable the ability for a NAC to report when the packet bus clock has been restored. Default = disableAll(2).
INT mdmTeInConnAttemptFail	1.3.6.1.4.1.429.1.6.13.1.1.23	INTEGER	read-write	Enables generation of a SNMP trap upon detection of an inbound connection attempt failure on the specified modem.
INT mdmTeOutConnAttemptFail	1.3.6.1.4.1.429.1.6.13.1.1.24	INTEGER	read-write	Enables generation of a SNMP trap upon detection of an outbound connection attempt failure on the specified modem.
INT mdmTe105ResponderTest	1.3.6.1.4.1.429.1.6.13.1.1.25	INTEGER	read-write	Enables generation of a SNMP trap upon detection of a 105 responder test on the specified modem.
mdmLs	1.3.6.1.4.1.429.1.6.14
mdmLsTable	1.3.6.1.4.1.429.1.6.14.1		not-accessible	A table defining all the Link Security parameters for each modem in the chassis.
mdmLsTableEntry	1.3.6.1.4.1.429.1.6.14.1.1		not-accessible	Link Security parameters for a modem. These define the link level security operations which take place when a call is negotiated.
INT mdmLsIndex	1.3.6.1.4.1.429.1.6.14.1.1.1	INTEGER	read-only	The index which uniquely identifies the modem to which this entry is applicable. The value corresponds to the value of the index to the entity table in the chassis MIB that corresponds to the same modem.
INT mdmLsSecurityEnable	1.3.6.1.4.1.429.1.6.14.1.1.2	INTEGER	read-write	Allows to disable/enable the dial security feature for the modem.
INT mdmLsFallbackPromptEnable	1.3.6.1.4.1.429.1.6.14.1.1.3	INTEGER	read-write	Disables/enables the prompting by the called modem when the auto pass password supplied by the caller fails or if no password is supplied at all.
INT mdmLsForcePromptEnable	1.3.6.1.4.1.429.1.6.14.1.1.4	INTEGER	read-write	If this is enabled, the modem will prompt the remote user for a password regardless of the success of the modem to negotiate the auto pass password.
INT mdmLsLocAccPasswdEnable	1.3.6.1.4.1.429.1.6.14.1.1.5	INTEGER	read-write	Disables/enables the Local Access Password feature used to establish security check when accessing any security setting.
INT mdmLsDialBackEnable	1.3.6.1.4.1.429.1.6.14.1.1.6	INTEGER	read-write	If this is set to enable the modem, after successful password validation, will disconnect and dial out to the originating modem.
STR mdmLsAutoPassPasswd	1.3.6.1.4.1.429.1.6.14.1.1.7	DisplayString	read-write	Contains the Auto Pass Password used for establishing Link security during call negotiation.
STR mdmLsLocalAccessPasswd	1.3.6.1.4.1.429.1.6.14.1.1.8	DisplayString	read-write	Contains the Local Access password used when accessing any security setting and when Local Access password feature is enabled.
STR mdmLsAccountPasswd	1.3.6.1.4.1.429.1.6.14.1.1.9	DisplayString	read-write	Contains the fall back password which must be entered if auto pass password is not satisfied.
mdmHs	1.3.6.1.4.1.429.1.6.15
mdmHsTable	1.3.6.1.4.1.429.1.6.15.1		not-accessible	A table containing the Hub security parameters accessible in the modem.
mdmHsEntry	1.3.6.1.4.1.429.1.6.15.1.1		not-accessible	There is one entry in this table for each modem entity found in the chassis mib entity table.
INT mdmHsIndex	1.3.6.1.4.1.429.1.6.15.1.1.1	INTEGER	read-only	An index that uniquely identifies the modem to which this row in the Hub Security table pertains. The value of this index matches the value of the index for the corresonding entity in the entity table of the Chassis MIB.
INT mdmHsDialInEnable	1.3.6.1.4.1.429.1.6.15.1.1.2	INTEGER	read-write	Allows the modem to be configured for dial-in security. Enabling this effectively disables the modem's built-in Link security operation. The default for this object is disabled.
INT mdmHsDialOutEnable	1.3.6.1.4.1.429.1.6.15.1.1.3	INTEGER	read-write	Allows modems to be configured for dial-out security. Enabling this effectively disables the modem's built-in link security operation. The default value for this object is disabled.
INT mdmHsDtrDcdDelay	1.3.6.1.4.1.429.1.6.15.1.1.4	INTEGER	read-write	Allows configuration of the time delay (in 100ths of a second) between reciept of DTR and assertion of DCD when the user on an incomming security call has successfully compleated the security dialog. This object only applies to modems using an RS232 like interface.
INT mdmHsDtrDsrDelay	1.3.6.1.4.1.429.1.6.15.1.1.5	INTEGER	read-write	Allows configuration of the delay (in 100ths of a second) between detection of DTR and assertion of DSR when an incomming security call has completed security negotiation successfully.
mdmAutoResponse	1.3.6.1.4.1.429.1.6.16
mdmArTable	1.3.6.1.4.1.429.1.6.16.1		not-accessible	Table of auto response scripts for each modem in the chassis. The number of table entries is specified by modemNumber.
mdmArEntry	1.3.6.1.4.1.429.1.6.16.1.1		not-accessible	List of configurable auto response scripts.
INT mdmArIndex	1.3.6.1.4.1.429.1.6.16.1.1.1	INTEGER	read-only	Index in to the auto response table. This index contains the unique value associated with the modem as defined in the chassis mib entity table.
OCT mdmArIncomConnectEstab	1.3.6.1.4.1.429.1.6.16.1.1.2	OCTET STRING	read-write	This script is triggered when a Total Control WAN HUB modem establishes a connection with a remote modem. The remote modem is the caller.
OCT mdmArOutgoConnectEstab	1.3.6.1.4.1.429.1.6.16.1.1.3	OCTET STRING	read-write	This script is triggered when a Total Control WAN HUB modem establishes a connection with a remote modem. The Total Control WAN HUB modem is the caller.
OCT mdmArIncomConnectTerm	1.3.6.1.4.1.429.1.6.16.1.1.4	OCTET STRING	read-write	This script is triggered after a remote modem has called a Total Control WAN HUB modem, but the connection between them terminated for some reason.
OCT mdmArOutgoConnectTerm	1.3.6.1.4.1.429.1.6.16.1.1.5	OCTET STRING	read-write	This script is triggered after a Total Control WAN HUB modem called a remote modem, but the connection between them terminated for some reason.
OCT mdmArConnectAttemptFail	1.3.6.1.4.1.429.1.6.16.1.1.6	OCTET STRING	read-write	This script is triggered when a Total Control WAN HUB modem fails to connect with a remote modem for an incoming or an outgoing call.
OCT mdmArConnectTimeExpire	1.3.6.1.4.1.429.1.6.16.1.1.7	OCTET STRING	read-write	This script is triggered when a connection duration exceeds the user defined connection time limit.
OCT mdmArResetByDte	1.3.6.1.4.1.429.1.6.16.1.1.8	OCTET STRING	read-write	This script is triggered when a modem has been reset by a DTE.
OCT mdmArDteXmitIdle	1.3.6.1.4.1.429.1.6.16.1.1.9	OCTET STRING	read-write	This script is triggered when a modem's DTE remains idle for specified amount of minutes that is defined by a user.
OCT mdmArBlersAtThresh	1.3.6.1.4.1.429.1.6.16.1.1.10	OCTET STRING	read-write	This script is triggered when a Total Control WAN HUB modem receives a certain amount of block errors. This amount can be configured by a user.
OCT mdmArFbacksAtThresh	1.3.6.1.4.1.429.1.6.16.1.1.11	OCTET STRING	read-write	This script is triggered when a Total Control WAN HUB modem reaches a certain amount of fall backs within a single session. This amount can be configured by a user.
OCT mdmArDialOutLoginFail	1.3.6.1.4.1.429.1.6.16.1.1.12	OCTET STRING	read-write	This script is triggered when a user, who is attempting to dial out from a Total Control WAN HUB modem that supports dial security, enters an invalid response to a prompt.
OCT mdmArDialOutRestrNum	1.3.6.1.4.1.429.1.6.16.1.1.13	OCTET STRING	read-write	This script is triggered when a user, who is attempting to dial out from a Total Control WAN HUB modem that supports dial security, uses a restricted number.
OCT mdmArDialInLoginFail	1.3.6.1.4.1.429.1.6.16.1.1.14	OCTET STRING	read-write	This script is triggered when a user, who is attempting to dial in from a remote modem in to a Total Control WAN HUB modem that supports dial security, enters an invalid response to a prompt.
OCT mdmArDialBackRestrNum	1.3.6.1.4.1.429.1.6.16.1.1.15	OCTET STRING	read-write	This script is triggered when a user, who is attempting to dial in from a remote modem in to a Total Control WAN HUB modem that supports dial security, requests the Total Control WAN HUB modem to dial back to a restricted number.
OCT mdmArDialBackRestModem	1.3.6.1.4.1.429.1.6.16.1.1.16	OCTET STRING	read-write	This script is triggered when a user, who is attempting to dial in from a remote modem in to a Total Control WAN HUB modem that supports dial security, requests the Total Control WAN HUB modem to dial back using a restricted Total Control WAN HUB modem.
OCT mdmArLoginAttemptsExceed	1.3.6.1.4.1.429.1.6.16.1.1.17	OCTET STRING	read-write	This script is triggered when a user, who is dialing in to or out of the Total Control WAN HUB modem, exceeds the number of correct user name/password response attempts.
OCT mdmArUserBlacklisted	1.3.6.1.4.1.429.1.6.16.1.1.18	OCTET STRING	read-write	This script is triggered when a user, who is dialing in to or out of the Total Control WAN HUB modem, exceeds the number of password prompt retries. At this point the user becomes black listed.
OCT mdmArAttmpLoginByBlistUsr	1.3.6.1.4.1.429.1.6.16.1.1.19	OCTET STRING	read-write	This script is triggered when a user, who has been black listed, is trying to dial in to or out of a Total Control WAN HUB modem.
OCT mdmArRspAttemptLimExceed	1.3.6.1.4.1.429.1.6.16.1.1.20	OCTET STRING	read-write	This script is triggered when a user, who is dialing in to or out of a Total Control WAN HUB modem, exceeds the number of security prompt retries during a single dial security session.
OCT mdmArWatchdog	1.3.6.1.4.1.429.1.6.16.1.1.21	OCTET STRING	read-write	This script is triggered when a software failure has occurred on a modem.
OCT mdmArMgtBusFailure	1.3.6.1.4.1.429.1.6.16.1.1.22	OCTET STRING	read-write	This script is triggered when a contact with a modem, via the management bus, has been lost.
OCT mdmArDtrTrue	1.3.6.1.4.1.429.1.6.16.1.1.23	OCTET STRING	read-write	This script is triggered when a modem's DTE transitions it DTR line from low to high and holds it high for the specified number of seconds. This amount is user configurable.
OCT mdmArDtrFalse	1.3.6.1.4.1.429.1.6.16.1.1.24	OCTET STRING	read-write	This script is triggered when a modem's DTE transitions it DTR line from high to low and holds it low for the specified number of seconds. This amount is user configurable.
OCT mdmArMdmRingNoAnswer	1.3.6.1.4.1.429.1.6.16.1.1.25	OCTET STRING	read-write	This script is triggered when a Total Control WAN HUB modem, configured for auto answer, fails to answer an incoming call within a specified number of rings. This amount is user configurable.
OCT mdmArDteRingNoAnswer	1.3.6.1.4.1.429.1.6.16.1.1.26	OCTET STRING	read-write	This script is triggered when a DTE fials to raise DTR in response to an incoming call for a specified amount of rings. This amount is user configurable.
OCT mdmArNoDialTone	1.3.6.1.4.1.429.1.6.16.1.1.27	OCTET STRING	read-write	This script is triggered when a Total Control WAN HUB modem goes off hook, but detects an inadequate dial tone level on an analog phone line.
OCT mdmArNoLoopCurrent	1.3.6.1.4.1.429.1.6.16.1.1.28	OCTET STRING	read-write	This script is triggered when a Total Control WAN HUB modem goes off hook, but it does not detect the presence of loop current on an analog phone line.
OCT mdmArTimer1	1.3.6.1.4.1.429.1.6.16.1.1.29	OCTET STRING	read-write	This script is triggered when the first general purpose timer expires.
OCT mdmArTimer2	1.3.6.1.4.1.429.1.6.16.1.1.30	OCTET STRING	read-write	This script is triggered when the second general purpose timer expires.
OCT mdmArTimer3	1.3.6.1.4.1.429.1.6.16.1.1.31	OCTET STRING	read-write	This script is triggered when the third general purpose timer expires.
OCT mdmArTimer4	1.3.6.1.4.1.429.1.6.16.1.1.32	OCTET STRING	read-write	This script is triggered when the fourth general purpose timer expires.
OCT mdmArPacketBusActive	1.3.6.1.4.1.429.1.6.16.1.1.33	OCTET STRING	read-write	This script is triggered when a packet bus active event is detected by the modem.
OCT mdmArPacketBusLost	1.3.6.1.4.1.429.1.6.16.1.1.34	OCTET STRING	read-write	This script is triggered when a packet bus lost event is detected by the modem.
mdmCe	1.3.6.1.4.1.429.1.6.17
mdmCeTable	1.3.6.1.4.1.429.1.6.17.1		not-accessible	A list of configurable Cellular Support object for a modem. The number of table entries is given by modemNumber.
mdmCeEntry	1.3.6.1.4.1.429.1.6.17.1.1		not-accessible	Objects which define the Cellular characteristics for a particular modem.
INT mdmCeIndex	1.3.6.1.4.1.429.1.6.17.1.1.1	INTEGER	read-only	This index value which uniquely identifies the modem to which this entry is applicable. The value corresponds to the index of the corresponding modem in the entity table of the chassis MIB.
INT mdmCeMnp10Dis	1.3.6.1.4.1.429.1.6.17.1.1.2	INTEGER	read-write	This object is bit 0 of S-register 60. It disable/enables MNP10 negotiation mostly used with cellular operations. (defualt=0)
INT mdmCeMnpxDis	1.3.6.1.4.1.429.1.6.17.1.1.3	INTEGER	read-write	This object is bit 1 of S-register 60. It will enable/disable the MNP extended services to be active during negotiation. This will mean that MNP10 will use V.42 to negotiate. (defualt=0)
INT mdmCeComp	1.3.6.1.4.1.429.1.6.17.1.1.4	INTEGER	read-write	This object is bit 2 of S-register 60. It selects which compression type will be negotiated if allowed by other modem settings. (default =0>
INT mdmCeOperDis	1.3.6.1.4.1.429.1.6.17.1.1.5	INTEGER	read-write	This object is bit 3 of S-register 60. It announces that at least one end of the link will be across a cellular network. Therefore, the Dyncamic Transmit Algorithm will be active. (default=0)
INT mdmCeLinkSpeed	1.3.6.1.4.1.429.1.6.17.1.1.6	INTEGER	read-write	This object is bit 4 of register 60 tells the modem which speed to establish the link at. (default=0)
INT mdmCeShortFormRules	1.3.6.1.4.1.429.1.6.17.1.1.7	INTEGER	read-write	This object is the S-register 61. It takes a value from 0 to 3 and regulates the V.42bis Short Form Negotiation rules. The short form assumes that the maximum string length is always 32 octets and that the direction of compression is always bi-directional. (default=0)
INT mdmCeDceBitraLim	1.3.6.1.4.1.429.1.6.17.1.1.8	INTEGER	read-write	This object is the S-register 64. It limits DCE bitrates to values equal to or below the chosen setting. (default=0)
INT mdmCeDceTxLev	1.3.6.1.4.1.429.1.6.17.1.1.9	INTEGER	read-write	This object is S-register 65. It selects DCE TX level to use during cellular operations. (default=0)
INT mdmCeV42EtcDis	1.3.6.1.4.1.429.1.6.17.1.1.10	INTEGER	read-write	This object is the bit 0 of S-register 66. It enables/disables ETC. (default=0)
INT mdmCeV42CellSite	1.3.6.1.4.1.429.1.6.17.1.1.11	INTEGER	read-write	This object is the bit 1 of S-register 66. It selects fixed or mobile site operations. (default=0)
INT mdmCeV42EtcCallToneDis	1.3.6.1.4.1.429.1.6.17.1.1.12	INTEGER	read-write	This object is the bit 2 of S-register 66. It enables/disables ETC calling tone. (default=0)
INT mdmCeV42EtcTxLevConDis	1.3.6.1.4.1.429.1.6.17.1.1.13	INTEGER	read-write	This object is the bit 3 of S-register 66. It enables/disables forced ETC TX level control. (default=0)
INT mdmCeDceStartRate	1.3.6.1.4.1.429.1.6.17.1.1.14	INTEGER	read-write	This object is the bits 4 and 5 of S-register 66. It sets the DCE startup rate. (default=0)
INT mdmCeV42DceTxDemDis	1.3.6.1.4.1.429.1.6.17.1.1.15	INTEGER	read-write	This object is the bit 6 of S-register 66. It enables/disables DCE TX De-emphasis. (default=0)
INT mdmCeMnp10FallbackDis	1.3.6.1.4.1.429.1.6.17.1.1.16	INTEGER	read-write	This object is the bit 5 of S-register 60. It enables/disables MNP10 fallback. (default=0)
INT mdmCeMnp10FallforDis	1.3.6.1.4.1.429.1.6.17.1.1.17	INTEGER	read-write	This object is the bit 6 of S-register 60. It enables/disables MNP10 fallforward. (default=0)
INT mdmCeDbNoEtcDis	1.3.6.1.4.1.429.1.6.17.1.1.18	INTEGER	read-write	This object is the bit 7 of S-register 66. It enables/disables non-ETC originate mode. (default=0/disable)
INT mdmCeMnpxDetPhEna	1.3.6.1.4.1.429.1.6.17.1.1.19	INTEGER	read-write	This object is the bit 7 of S-register 60. It enables/disables the MNPX detection phase during connection establishment. (default=0/enable).
mdmSts	1.3.6.1.4.1.429.1.6.18
mdmStsTable	1.3.6.1.4.1.429.1.6.18.1		not-accessible	A table containing configuration information for each NAC in the NAS chassis that supports packet bus datagrams.
mdmStsEntry	1.3.6.1.4.1.429.1.6.18.1.1		not-accessible	There is one configuration row for each modem entity.
INT mdmStsIndex	1.3.6.1.4.1.429.1.6.18.1.1.1	INTEGER	read-only	A unique value for each card in the chassis. The value of this object matches the value of the index of the corresponding card's entry in the entity table of the chassis MIB.
INT mdmStsPbClock	1.3.6.1.4.1.429.1.6.18.1.1.2	INTEGER	read-only	This object defines the current status of the packet bus clock.
mdmMa	1.3.6.1.4.1.429.1.6.19
mdmMaTable	1.3.6.1.4.1.429.1.6.19.1		not-accessible	A Mapping table entry, containing objects which define the card level configuration each modem is mapped to and the unique change indicator.
mdmMaEntry	1.3.6.1.4.1.429.1.6.19.1.1		not-accessible	Objects which define the Mapping and Status for a particular modem.
INT mdmMaIndex	1.3.6.1.4.1.429.1.6.19.1.1.1	INTEGER	read-only	This index value which uniquely identifies the modem to which this entry is applicable. The value corresponds to the index of the corresponding modem in the entity table of the chassis MIB.
INT mdmMaChangeIndicator	1.3.6.1.4.1.429.1.6.19.1.1.2	INTEGER	read-only	A value of changed indicates that the card level configuration for a specific channel on a HDM is not the one in use on that channel.
INT mdmMaChannelConfig	1.3.6.1.4.1.429.1.6.19.1.1.3	INTEGER	read-write	Values of group(1), group(2), group(3), group(4) represent the HDM card level configuration of 1..4 used by this channel.

RFC description

3Com modem identification and configuration MIB providing hardware and software revision information for modems in NAS systems.

Start monitoring Dial-up modem / network access server (NAS) modem pool device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download MDM-MIB

What Is MDM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description