All MIBs › LIEBERT-GP-POWER-MIB
Organization: Liebert Corporation
Last Updated: 2013-07-10
Category: Domain: Power/UPS, Vendor: Liebert
Description: Defines power measurement and management objects for Liebert GlobalProducts UPS, PDU, and power conditioning equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is LIEBERT-GP-POWER-MIB?
This is a Liebert (Vertiv) private MIB covering power-related objects across Liebert's GlobalProducts UPS, PDU, and power-conditioning equipment line, used in data center and facility power management. It exposes hardware health and configuration data centered on battery subsystems: counts of installed, failed, redundant, and active battery modules, battery test results, nominal capacity, float voltage, end-of-discharge voltage, and configurable warning thresholds like low-battery warning time and automatic test interval. Its monitoring purpose is explicitly hardware status monitoring for UPS battery backup health, catching failed battery modules before a utility outage exposes the shortfall, tracking battery test results to confirm the UPS can actually deliver its rated runtime, and using module warning counts as an early alert that battery capacity is degrading. It is a Liebert-specific MIB not built on a shared IETF power standard, though it parallels the general intent of the standards-based UPS-MIB (RFC 1628). It is deployed on Liebert/Vertiv UPS systems, PDUs, and battery cabinets protecting data center and critical-facility power infrastructure. Engineers can download the LIEBERT-GP-POWER-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in LIEBERT-GP-POWER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Liebert/Vertiv UPS system
- Liebert/Vertiv PDU and power-conditioning equipment
Monitoring Examples
An administrator would poll lgpPwrNumberInstalledBatteryModules against lgpPwrNumberFailedBatteryModules to compute how many battery modules are currently down, and check lgpPwrNumberRedundantBatteryModules versus lgpPwrNumberActiveBatteryModules to confirm the UPS still has its designed redundancy. lgpPwrBatteryTestResult would be checked after a scheduled self-test, governed by lgpPwrAutomaticBatteryTestInterval, to verify the battery bank actually passed, while lgpPwrBatteryFloatVoltage and lgpPwrBatteryEndOfDischargeVoltage give the electrical parameters used to judge battery health. A rising lgpPwrNumberBatteryModuleWarnings count alongside a falling active-module count would be a clear signal of imminent runtime-capacity loss.
What Can Be Monitored
- installed/failed/active/redundant battery module counts
- battery self-test result
- battery float voltage
- battery end-of-discharge voltage
- automatic battery test interval
- low-battery warning time threshold
This MIB depends on
Related MIBs
Imported Objects
From LIEBERT-GP-REGISTRATION-MIB
| lgpPower | OBJECT-IDENTITY |
| liebertPowerModuleReg | OBJECT-IDENTITY |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| liebertGlobalProductsPowerModule | 1.3.6.1.4.1.476.1.42.1.6.1 | The MIB module used to register Liebert POWER related SNMP OIDs. Copyright 2000-2008 Liebert Corporation. All rights reserved. Reproduction of this document is authorized on the condition that the forgoing copyright notice is included. This Specification is supplied 'AS IS' and Liebert Corporation makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| lgpPwrBattery | 1.3.6.1.4.1.476.1.42.3.5.1 | This sub-tree is used to register Liebert Power Battery object identifiers. | ||
| I32 lgpPwrNumberInstalledBatteryModules | 1.3.6.1.4.1.476.1.42.3.5.1.1 | Integer32 | read-only | The number of battery modules installed in the device. |
| I32 lgpPwrNumberFailedBatteryModules | 1.3.6.1.4.1.476.1.42.3.5.1.2 | Integer32 | read-only | The number of battery modules in the device that have failed. |
| I32 lgpPwrNumberRedundantBatteryModules | 1.3.6.1.4.1.476.1.42.3.5.1.3 | Integer32 | read-only | The number of redundant battery modules in the device. |
| I32 lgpPwrNumberActiveBatteryModules | 1.3.6.1.4.1.476.1.42.3.5.1.4 | Integer32 | read-only | The number of active battery modules in the device. |
| I32 lgpPwrConfigLowBatteryWarningTime | 1.3.6.1.4.1.476.1.42.3.5.1.5 | Integer32 | read-write | The value of the device's estimated minutes of remaining battery at which a lgpEventLowBatteryWarning notification will be sent. |
| I32 lgpPwrNumberBatteryModuleWarnings | 1.3.6.1.4.1.476.1.42.3.5.1.6 | Integer32 | read-only | The number of battery modules in the device that have a warning. |
| I32 lgpPwrBatteryCount | 1.3.6.1.4.1.476.1.42.3.5.1.7 | Integer32 | read-only | The number of batteries installed. |
| INT lgpPwrBatteryTestResult | 1.3.6.1.4.1.476.1.42.3.5.1.8 | INTEGER | read-only | The outcome of the previous battery test. |
| I32 lgpPwrNominalBatteryCapacity | 1.3.6.1.4.1.476.1.42.3.5.1.9 | Integer32 | read-write | The nominal battery capacity of the system (in minutes) at full load. |
| I32 lgpPwrBatteryFloatVoltage | 1.3.6.1.4.1.476.1.42.3.5.1.10 | Integer32 | read-write | The battery float voltage of the system. |
| I32 lgpPwrBatteryEndOfDischargeVoltage | 1.3.6.1.4.1.476.1.42.3.5.1.11 | Integer32 | read-write | The battery voltage threshold at which the batteries are considered completely discharged. |
| I32 lgpPwrAutomaticBatteryTestInterval | 1.3.6.1.4.1.476.1.42.3.5.1.12 | Integer32 | read-write | The automatic battery test interval. |
| I32 lgpPwrAutomaticBatteryTestCountdown | 1.3.6.1.4.1.476.1.42.3.5.1.13 | Integer32 | read-write | The time remaining before the next battery test. |
| INT lgpPwrBatteryChargeStatus | 1.3.6.1.4.1.476.1.42.3.5.1.14 | INTEGER | read-only | The present state of the system's battery charge. A value of 'charging' indicates the batteries are currently charging. A value of 'discharging' indicates the batteries are currently discharging. A value of 'fullycharged' indicates the batteries are charged to their full capacity. A value of 'notfullycharged' indicates the battery charge is neither fully charged, charging or discharging. |
| INT lgpPwrBatteryLifeEnhancer | 1.3.6.1.4.1.476.1.42.3.5.1.15 | INTEGER | read-only | The state of the battery life enhancer. When 'on', it will preserve battery life. |
| INT lgpPwrBatteryCharger | 1.3.6.1.4.1.476.1.42.3.5.1.16 | INTEGER | read-only | The state of the battery charger. |
| INT lgpPwrBatteryChargeMode | 1.3.6.1.4.1.476.1.42.3.5.1.17 | INTEGER | read-only | The mode of the battery charger: 'float' charging or 'equalize' charging. |
| I32 lgpPwrBatteryTimeRemaining | 1.3.6.1.4.1.476.1.42.3.5.1.18 | Integer32 | read-only | An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off. NOTE: A UPS is expected to provide a battery time remaining value when not operating on battery. However, if the system is not capable of providing this information, then this point will return 65535 to indicate that the value is unavailable. |
| I32 lgpPwrBatteryCapacity | 1.3.6.1.4.1.476.1.42.3.5.1.19 | Integer32 | read-only | The present percentage of battery capacity. |
| lgpPwrBatteryCabinet | 1.3.6.1.4.1.476.1.42.3.5.1.20 | This sub-tree contains items related to battery cabinets. | ||
| I32 lgpPwrBatteryCabinetCount | 1.3.6.1.4.1.476.1.42.3.5.1.20.1 | Integer32 | read-write | The number of battery cabinets installed with this device. Note some devices may not permit writing a value to this object. |
| INT lgpPwrBatteryCabinetType | 1.3.6.1.4.1.476.1.42.3.5.1.20.2 | INTEGER | read-write | The type of battery cabinet(s) installed on this device. Enumeration definitions: notSpecified - The type has not been specified in the device's configuration. internal - Battery cabinets are internal to the device. external - Device has external battery cabinets installed. lrt - Long Run Time cabinets. Note some devices may not permit writing a value to this object. |
| I32 lgpPwrBatteryCabinetRatedCapacity | 1.3.6.1.4.1.476.1.42.3.5.1.20.3 | Integer32 | read-write | Battery cabinet rated capacity (tenths of Amp-hours). This assumes that each cabinet is of the same type and capacity. This is not a sum of the rating for all attached cabinets. Note some devices may not permit writing a value to this object. |
| I32 lgpPwrBatteryLeadAcidCellCount | 1.3.6.1.4.1.476.1.42.3.5.1.20.4 | Integer32 | read-write | Battery cell count - lead-acid. The number of cells that comprise the lead acid battery string. |
| I32 lgpPwrBatteryNiCadCellCount | 1.3.6.1.4.1.476.1.42.3.5.1.20.5 | Integer32 | read-write | Battery cell count - nickel-cadmium. The number of cells that comprise the nickel-cadmium battery string. |
| I32 lgpPwrBatteryAmpHoursConsumed | 1.3.6.1.4.1.476.1.42.3.5.1.21 | Integer32 | read-write | The cumulative battery Amp-hours withdrawn over the life of the battery. This value persists across reboots. Typically, this value is reset back to zero when the batteries are replaced. |
| I32 lgpPwrBatteryAmpHoursDischargeConsumed | 1.3.6.1.4.1.476.1.42.3.5.1.22 | Integer32 | read-write | The battery Amp-hours withdrawn during the current/latest discharge. This value does not persist across reboots. |
| U32 lgpPwrBatteryLastDischargeTime | 1.3.6.1.4.1.476.1.42.3.5.1.23 | Unsigned32 | read-write | The date and time of the last battery discharge. Typically this is the time when the discharge starts. This value persists across reboots. The date and time are determined in seconds since the epoch on January 1, 1970. |
| U32 lgpPwrBatteryLastCommissionTime | 1.3.6.1.4.1.476.1.42.3.5.1.24 | Unsigned32 | read-write | The date and time when the battery system was put into service. This information persists across system reboot events. It is the responsibility of Service to reset this date/time when the batteries are replaced. The date and time are determined in seconds since the epoch on January 1, 1970. |
| I32 lgpPwrBatteryPresentDischargeTime | 1.3.6.1.4.1.476.1.42.3.5.1.25 | Integer32 | read-only | The total time spent on battery during the current or last discharge. NOTE: While not discharging, some systems may display zero instead of the last discharge. |
| INT lgpPwrBatteryCapacityStatus | 1.3.6.1.4.1.476.1.42.3.5.1.26 | INTEGER | read-only | The indication of the capacity remaining in the UPS system's batteries. NOTE: In a single-module system, this point is intended to have the same behavior as the RFC1628 point upsBatteryStatus. |
| INT lgpPwrBatteryCircuitBreakerState | 1.3.6.1.4.1.476.1.42.3.5.1.27 | INTEGER | read-only | The state of the Battery Circuit Breaker. |
| lgpPwrMeasurements | 1.3.6.1.4.1.476.1.42.3.5.2 | This sub-tree registers Liebert Power Measurement object identifiers. The sub-tree contains tables and well known power measurement points. | ||
| lgpPwrWellKnownMeasurementPoints | 1.3.6.1.4.1.476.1.42.3.5.2.1 | This sub-tree registers well known Liebert Power Measurement Points. The object identifier names usually imply locations where the measurement is taken -- such as 'input', 'output' and 'bypass'. | ||
| lgpPwrSource1Input | 1.3.6.1.4.1.476.1.42.3.5.2.1.1 | This sub-tree is used to register a source 1 input as a well known measurement point. It is intended that no sub-trees be created below this node. Power input to the managed device from power source 1. Many power systems contain more than one input source and many of them have more than one measurement point per input source. This identifier represents one input source for the system but does not necessarily represent the 'first' one. The input sources' numbering with respect to 'lgpPwrSource1Input' etc. may depend on the physical wiring of the system when it was installed. | ||
| lgpPwrSource2Input | 1.3.6.1.4.1.476.1.42.3.5.2.1.2 | This sub-tree is used to register a source 2 input as a well known measurement point. It is intended that no sub-trees be created below this node. Power input to the managed device from power source 2. Many power systems contain more than one input source and many of them have more than one measurement point per input source. This identifier represents one input source for the system but does not necessarily represent the 'first' one. The input sources' numbering with respect to 'lgpPwrSource2Input' etc. may depend on the physical wiring of the system when it was installed. | ||
| lgpPwrSourcePdu1Input | 1.3.6.1.4.1.476.1.42.3.5.2.1.3 | This sub-tree is used to register a source PDU 1 input as a well known measurement point. It is intended that no sub-trees be created below this node. Power input to the managed device from power distribution unit 1. Many power systems contain more than one input source and many of them have more than one measurement point per input source. This identifier represents one input source for the system but does not necessarily represent the 'first' one. The input sources' numbering with respect to 'lgpPwrSourcePdu1Input' etc. may depend on the physical wiring of the system when it was installed. | ||
| lgpPwrSourcePdu2Input | 1.3.6.1.4.1.476.1.42.3.5.2.1.4 | This sub-tree is used to register a source PDU 2 input as a well known measurement point. It is intended that no sub-trees be created below this node. Power input to the managed device from power distribution unit 1. Many power systems contain more than one input source and many of them have more than one measurement point per input source. This identifier represents one input source for the system but does not necessarily represent the 'first' one. The input sources' numbering with respect to 'lgpPwrSourcePdu2Input' etc. may depend on the physical wiring of the system when it was installed. | ||
| lgpPwrOutputToLoad | 1.3.6.1.4.1.476.1.42.3.5.2.1.5 | This sub-tree is used to register the output to the critical load as a well known measurement point. It is intended that no sub-trees be created below this node. | ||
| lgpPwrMeasBattery | 1.3.6.1.4.1.476.1.42.3.5.2.1.6 | This sub-tree is used to register a battery as a well known measurement point. It is intended that no sub-trees be created below this node. | ||
| lgpPwrMeasBypass | 1.3.6.1.4.1.476.1.42.3.5.2.1.7 | This sub-tree is used to register a bypass as a well known measurement point. It is intended that no sub-trees be created below this node. | ||
| lgpPwrMeasDcBus | 1.3.6.1.4.1.476.1.42.3.5.2.1.8 | This sub-tree is used to register a DC bus as a well known measurement point. It is intended that no sub-trees be created below this node. | ||
| lgpPwrMeasSystemOutput | 1.3.6.1.4.1.476.1.42.3.5.2.1.9 | This sub-tree is used to register the output of a multi-module system as a well known measurement point. It is intended that no sub-trees be created below this node. This identifier represents the power related data of the system. | ||
| lgpPwrMeasBatteryCabinet | 1.3.6.1.4.1.476.1.42.3.5.2.1.10 | This sub-tree is used to register the voltage between the most negative and the most postive terminals of a battery cabinet. To determine the cabinet being described in a multi-cabinet system, this point implements an additional two indexes. The first index describes the module the cabinet is located in. The second index describes the cabinet number. In an SMS(Single-Module System) the first index is always 1. Example: lgpPwrMeasBatteryCabinet.2.4 'lgpPwrMeasBatteryCabinet' = Point is a battery cabinet. '.2' = Cabinet is in the second module. '.4' = Cabinet number 4 | ||
| lgpPwrMeasurementPointTable | 1.3.6.1.4.1.476.1.42.3.5.2.2 | not-accessible | This table contains a list of AC power measurement point entries. The table contains zero, one, or many rows, depending upon the number of power related measurement points available. The NMS cannot create or delete rows from the table. The rows are created by the agent based upon the capabilities of the managed device. Each row in the table represents a series of measurements on a given point or location within the system. Measurement points/locations are identified by the object identifier 'lgpPwrMeasurementPointId' in the 'LgpPwrMeasurementPointEntry' object. The actual measurement being taken at that identified point is identified by the other corresponding columns in the LgpPwrMeasurementPointEntry for the particular row of the table. | |
| lgpPwrMeasurementPointEntry | 1.3.6.1.4.1.476.1.42.3.5.2.2.1 | not-accessible | This entry defines the measurements to be populated in the various columns of the 'lgpPwrMeasurementPointTable'. | |
| U32 lgpPwrMeasurementPointIndex | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.1 | Unsigned32 | not-accessible | This is the index that indicates the row of the 'lgpPwrMeasurementPointTable' for a power measurement point. |
| OID lgpPwrMeasurementPointId | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.2 | OBJECT IDENTIFIER | read-only | An OID representing a well known measurement point. These object identifiers indicate a point or location of power measurement in a power system. The OID's name usually implies a location of the measurement point such as 'input', 'output', 'bypass' etc. |
| I32 lgpPwrMeasurementPointNumLines | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.3 | Integer32 | read-only | The number of lines on the indicated power measurement point. (i.e. the number of phases on the power source being measured.) |
| I32 lgpPwrMeasurementPointNomVolts | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.4 | Integer32 | read-only | The magnitude of the nominal voltage on the power source being measured. |
| I32 lgpPwrMeasurementPointNomFrequency | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.5 | Integer32 | read-only | The nominal or configured/expected frequency for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointFrequency | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.6 | Integer32 | read-only | The present (actual) frequency for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointApparentPower | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.7 | Integer32 | read-only | The present apparent AC power for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointTruePower | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.8 | Integer32 | read-only | The present AC power for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointPowerFactor | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.9 | Integer32 | read-only | The present Power Factor for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointWattHours | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.10 | Integer32 | read-only | The present number of Watt Hours for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointVAPercent | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.11 | Integer32 | read-only | The percentage of the rated apparent AC power of the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointNeutralCurrent | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.12 | Integer32 | read-only | The present neutral current of the power point indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointGroundCurrent | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.13 | Integer32 | read-only | The present ground current of the power point indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointNomCurrent | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.14 | Integer32 | read-only | The nominal or configured/expected current of the power point indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointNomPowerFactor | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.15 | Integer32 | read-only | The nominal or configured/expected power factor of the power point indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointNomVA | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.16 | Integer32 | read-write | The nominal or configured/expected apparent AC power for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| I32 lgpPwrMeasurementPointNomW | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.17 | Integer32 | read-write | The nominal or configured/expected true AC power for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. |
| INT lgpPwrMeasurementPointPowerFactorTag | 1.3.6.1.4.1.476.1.42.3.5.2.2.1.19 | INTEGER | read-only | The present description of the Power Factor for the power source indicated by 'lgpPwrMeasurementPointId' in the corresponding row in the lgpPwrMeasurementPointTable. If Leading, the load is said to be capacitive and the phase of the current leads the voltage. If Lagging, the load is said to be inductive and the phase of the current lags the voltage. |
| lgpPwrLineMeasurementTable | 1.3.6.1.4.1.476.1.42.3.5.2.3 | not-accessible | A list of power measurements for each phase/line for a given power measurement point/location in the 'lgpPwrMeasurementPointTable'. The lgpPwrMeasurementPointIndex in this table corresponds to the index in the lgpPwrMeasurementPointTable. This table contains zero, one, or many rows, depending upon the number of power line source objects available. The NMS cannot create or delete rows from the table. The rows are created by the agent based upon the capabilities of the managed device. | |
| lgpPwrLineMeasurementEntry | 1.3.6.1.4.1.476.1.42.3.5.2.3.1 | not-accessible | This entry defines the contents of the columns for the table 'lgpPwrLineMeasurementTable'. | |
| U32 lgpPwrMeasurementPtIndex | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.1 | Unsigned32 | not-accessible | This is the index indicating the row of the table 'lgpPwrMeasurementPointTable' for a power measurement point. |
| U32 lgpPwrLineMeasurementIndex | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.2 | Unsigned32 | not-accessible | This is the index indicating the row of the table 'lgpPwrLineMeasurementTable' for a power measurement point. |
| OID lgpPwrMeasurementPoint | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.3 | OBJECT IDENTIFIER | read-only | An OID representing a well known measurement point. These object identifiers indicate a point or location of power measurement in a power system. The OID name usually implies a location of the measurement point such as 'input', 'output', 'bypass', etc. |
| I32 lgpPwrLineMeasurementVoltsLL | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.4 | Integer32 | read-only | The present Line-to-Line voltage measurement for the indicated source. The line being measured is given by the lgpPwrLineMeasurementIndex [1 = AB, 2 = BC, 3 = CA]. |
| I32 lgpPwrLineMeasurementVoltsLN | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.5 | Integer32 | read-only | The present Line-to-neutral voltage measurement for the indicated source. The line being measured is given by the lgpPwrLineMeasurementIndex where [1 = A, 2 = B, 3 = C]. |
| I32 lgpPwrLineMeasurementCurrent | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.6 | Integer32 | read-only | The present current measurement for the indicated source. The line being measured is given by the 'lgpPwrLineMeasurementIndex' where [1 = A, 2 = B, 3 = C]. |
| I32 lgpPwrLineMeasurementCapacity | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.7 | Integer32 | read-only | The percentage of the power capacity presently being used on this line. |
| I32 lgpPwrLineMeasurementVA | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.8 | Integer32 | read-only | The present apparent AC line power. |
| I32 lgpPwrLineMeasurementTruePower | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.9 | Integer32 | read-only | The present AC line power measured in watts. |
| I32 lgpPwrLineMeasurementVoltageTHD | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.10 | Integer32 | read-only | The present total harmonic distortion on the AC line voltage. |
| I32 lgpPwrLineMeasurementCurrentTHD | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.11 | Integer32 | read-only | The present total harmonic distortion on the AC line current. |
| I32 lgpPwrLineMeasurementKFactorCurrent | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.12 | Integer32 | read-only | The present line K Factor. |
| I32 lgpPwrLineMeasurementCrestFactorCurrent | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.13 | Integer32 | read-only | The present crest factor of the line current. |
| I32 lgpPwrLineMeasurementPowerFactor | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.14 | Integer32 | read-only | The present Power Factor for the line. |
| INT lgpPwrLineMeasurementPowerFactorTag | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.15 | INTEGER | read-only | The present description of the Power Factor for the line. If Leading, the load is said to be capacitive and the phase of the current leads the voltage. If Lagging, the load is said to be inductive and the phase of the current lags the voltage. |
| I32 lgpPwrLineMeasurementMaxVolts | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.16 | Integer32 | read-only | The maximum voltage measurement recorded for the indicated source since the command 'lgpPwrStatisticsReset' was executed. |
| I32 lgpPwrLineMeasurementMinVolts | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.17 | Integer32 | read-only | The minimum voltage measurement recorded for the indicated source since the command 'lgpPwrStatisticsReset' was executed. |
| I32 lgpPwrLineMeasurementVAR | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.18 | Integer32 | read-only | The present reactive AC line power of the power source indicated by 'lgpPwrMeasurementPoint'. |
| I32 lgpPwrLineMeasurementPercentLoad | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.19 | Integer32 | read-only | The present percent load of the AC line power. |
| I32 lgpPwrLineMeasurementVolts | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.20 | Integer32 | read-only | The present voltage measurement for the indicated source. |
| I32 lgpPwrLineMeasurementVACapacity | 1.3.6.1.4.1.476.1.42.3.5.2.3.1.21 | Integer32 | read-only | The percentage of the apparent power capacity presently being used on this line. |
| lgpPwrDcMeasurementPointTable | 1.3.6.1.4.1.476.1.42.3.5.2.4 | not-accessible | This table contains a list of DC power measurement point entries. The table contains zero, one, or many rows, depending upon the number of power related measurement points available. The NMS cannot create or delete rows from the table. The rows are created by the agent based upon the capabilities of the managed device. Each row in the table represents a series of measurements on a given point or location within the system. Measurement points/locations are identified by the object identifier 'lgpPwrDcMeasurementPointId' in the 'LgpPwrDcMeasurementPointEntry' object. The actual measurement being taken at that identified point is identified by the other corresponding columns in the LgpPwrDcMeasurementPointEntry for the particular row of the table. | |
| lgpPwrDcMeasurementPointEntry | 1.3.6.1.4.1.476.1.42.3.5.2.4.1 | not-accessible | This entry defines the measurements to be populated in the various columns of the 'lgpPwrDcMeasurementPointTable'. | |
| U32 lgpPwrDcMeasurementPointIndex | 1.3.6.1.4.1.476.1.42.3.5.2.4.1.1 | Unsigned32 | not-accessible | This is the index that indicates the row of the 'lgpPwrMeasurementPointTable' for a power measurement point. |
| OID lgpPwrDcMeasurementPointId | 1.3.6.1.4.1.476.1.42.3.5.2.4.1.2 | OBJECT IDENTIFIER | read-only | An OID representing a well known measurement point. These object identifiers indicate a point or location of power measurement in a power system. The OID's name usually implies a location of the measurement point such as 'input', 'output', 'bypass' etc. |
| I32 lgpPwrDcMeasurementPointSubID | 1.3.6.1.4.1.476.1.42.3.5.2.4.1.3 | Integer32 | read-only | The identifier used to differentiate between identical thresholds for a given point index and point ID in the DC measurements table. |
| I32 lgpPwrDcMeasurementPointVolts | 1.3.6.1.4.1.476.1.42.3.5.2.4.1.4 | Integer32 | read-only | The present DC voltage for the power source indicated by 'lgpPwrDcMeasurementPointId' in the corresponding row in the lgpPwrDcMeasurementPointTable. |
| I32 lgpPwrDcMeasurementPointCurrent | 1.3.6.1.4.1.476.1.42.3.5.2.4.1.5 | Integer32 | read-only | The present DC current for the power source indicated by 'lgpPwrDcMeasurementPointId' in the corresponding row in the lgpPwrDcMeasurementPointTable. |
| I32 lgpPwrDcMeasurementPointNomVolts | 1.3.6.1.4.1.476.1.42.3.5.2.4.1.6 | Integer32 | read-only | The nominal(configured/expected) DC voltage for the power source indicated by 'lgpPwrDcMeasurementPointId' in the corresponding row in the lgpPwrDcMeasurementPointTable. |
| I32 lgpPwrDcMeasurementPointTruePower | 1.3.6.1.4.1.476.1.42.3.5.2.4.1.7 | Integer32 | read-only | The present DC power for the power source indicated by 'lgpPwrDcMeasurementPointId' in the corresponding row in the lgpPwrDcMeasurementPointTable. |
| lgpPwrWellKnownMeasurementTypes | 1.3.6.1.4.1.476.1.42.3.5.2.5 | This sub-tree registers well known Liebert Power Measurement Types. The object identifier names usually encompass units of measure, lines of reference, and device location. The OID's name usually implies a measurement type such as 'voltsAC', 'current', 'voltsDc', 'VoltsLL', etc. | ||
| lgpPwrVoltsAc | 1.3.6.1.4.1.476.1.42.3.5.2.5.1 | This identifier represents an AC voltage. | ||
| lgpPwrVoltsDc | 1.3.6.1.4.1.476.1.42.3.5.2.5.2 | This identifier represents a DC voltage. | ||
| lgpPwrAmpsNeutral | 1.3.6.1.4.1.476.1.42.3.5.2.5.3 | This identifier represents a current measurement in Amps on the neutral line. | ||
| lgpPwrStatus | 1.3.6.1.4.1.476.1.42.3.5.3 | This sub-tree registers Liebert Power Status object identifiers. This is the location of power related status information that does not fit into a more specific category such as the lgpPwrConversion sub-tree. | ||
| I32 lgpPwrTransferCount | 1.3.6.1.4.1.476.1.42.3.5.3.1 | Integer32 | read-only | Number of times that the output load has been transferred between the available input sources. |
| I32 lgpPwrAutoTransferTimer | 1.3.6.1.4.1.476.1.42.3.5.3.2 | Integer32 | read-only | The required wait time between output load auto transfer attempts between available input sources. |
| INT lgpPwrAutoReTransferEnabled | 1.3.6.1.4.1.476.1.42.3.5.3.3 | INTEGER | read-only | The ability to retransfer the output load automatically to the well known measurement source from the 'lgpPwrWellKnownMeasurements' sub-tree that is the preferred input source of the system |
| I32 lgpPwrSyncPhaseAngle | 1.3.6.1.4.1.476.1.42.3.5.3.4 | Integer32 | read-only | The phase angle difference of source 1 in relation to source 2. |
| INT lgpPwrParallelSystemOutputToLoadSource | 1.3.6.1.4.1.476.1.42.3.5.3.5 | INTEGER | read-only | The source supporting the parallel system's load. |
| INT lgpPwrDcToDcConverter | 1.3.6.1.4.1.476.1.42.3.5.3.6 | INTEGER | read-only | The state of the DC to DC converter. |
| INT lgpPwrOutputToLoadOnInverter | 1.3.6.1.4.1.476.1.42.3.5.3.7 | INTEGER | read-only | The present source of output power is the Inverter. |
| INT lgpPwrBatteryChargeCompensating | 1.3.6.1.4.1.476.1.42.3.5.3.8 | INTEGER | read-only | The system is adjusting the battery charging algorithm to accommodate for the battery temperature. |
| INT lgpPwrInverterReady | 1.3.6.1.4.1.476.1.42.3.5.3.9 | INTEGER | read-only | The ability of the inverter to support the output load of the system. |
| INT lgpPwrOutputToLoadOnBypass | 1.3.6.1.4.1.476.1.42.3.5.3.10 | INTEGER | read-only | The present source of output power is the Bypass. |
| INT lgpPwrBoost | 1.3.6.1.4.1.476.1.42.3.5.3.11 | INTEGER | read-only | The present state of the boost circuitry |
| INT lgpPwrBuck | 1.3.6.1.4.1.476.1.42.3.5.3.12 | INTEGER | read-only | The present state of the buck circuitry |
| INT lgpPwrShutdownOverTemperature | 1.3.6.1.4.1.476.1.42.3.5.3.13 | INTEGER | read-only | The system has previously shutdown due to an over temperature condition. |
| INT lgpPwrShutdownOverload | 1.3.6.1.4.1.476.1.42.3.5.3.14 | INTEGER | read-only | The system has previously shutdown due to an over load condition. |
| INT lgpPwrShutdownDcBusOverload | 1.3.6.1.4.1.476.1.42.3.5.3.15 | INTEGER | read-only | The system has previously shutdown due to a DC bus over load condition. |
| INT lgpPwrShutdownOutputShort | 1.3.6.1.4.1.476.1.42.3.5.3.16 | INTEGER | read-only | The system has previously shutdown due to an output short condition. |
| INT lgpPwrShutdownLineSwap | 1.3.6.1.4.1.476.1.42.3.5.3.17 | INTEGER | read-only | The system has previously shutdown due to a condition where the line and neutral were reversed. |
| INT lgpPwrShutdownLowBattery | 1.3.6.1.4.1.476.1.42.3.5.3.18 | INTEGER | read-only | The system has previously shutdown due to a low battery condition. |
| INT lgpPwrShutdownRemote | 1.3.6.1.4.1.476.1.42.3.5.3.19 | INTEGER | read-only | The system has previously shutdown due to a remote shutdown command. |
| INT lgpPwrShutdownInputUnderVoltage | 1.3.6.1.4.1.476.1.42.3.5.3.20 | INTEGER | read-only | The system has previously shutdown due to an under voltage condition during startup. |
| INT lgpPwrShutdownPowerFactorCorrectionFailure | 1.3.6.1.4.1.476.1.42.3.5.3.21 | INTEGER | read-only | The system has previously shutdown due to a power factor correction startup failure. |
| INT lgpPwrShutdownHardware | 1.3.6.1.4.1.476.1.42.3.5.3.22 | INTEGER | read-only | The system has previously shutdown due external shutdown signal. |
| INT lgpPwrRedundantSubModule | 1.3.6.1.4.1.476.1.42.3.5.3.23 | INTEGER | read-only | The system has a redundant battery module installed. |
| INT lgpPwrBypassReady | 1.3.6.1.4.1.476.1.42.3.5.3.24 | INTEGER | read-only | The ability of the bypass to support the output load of the system. If Yes, the bypass is available to transfer to. |
| INT lgpPwrGeneratorStatus | 1.3.6.1.4.1.476.1.42.3.5.3.25 | INTEGER | read-only | The state of the system generator. |
| INT lgpPwrRotaryBreakerStatus | 1.3.6.1.4.1.476.1.42.3.5.3.26 | INTEGER | read-only | The state of the system rotary breaker. |
| INT lgpPwrPowerFactorCorrection | 1.3.6.1.4.1.476.1.42.3.5.3.27 | INTEGER | read-only | The state of the power factor correction circuitry of the system. |
| I32 lgpPwrBypassSyncDiff | 1.3.6.1.4.1.476.1.42.3.5.3.28 | Integer32 | read-only | The phase angle difference between the inverter output and bypass source. A positive value means the inverter leads the bypass source. A negative value means the inverter lags the bypass source. |
| I32 lgpPwrBypassOverloadShutdownTime | 1.3.6.1.4.1.476.1.42.3.5.3.29 | Integer32 | read-only | The calculated time remaining before bypass static switch shutdown due to the present overload condition. If the bypass is not in an overload condition, this object returns -1. |
| I32 lgpPwrInverterOverloadShutdownTime | 1.3.6.1.4.1.476.1.42.3.5.3.30 | Integer32 | read-only | The calculated time remaining before inverter shutdown. The calculated time of inverter operation remaining for the present overload event. Note: If the inverter is not experiencing an overload event this point will return 65535 indicating this value is unavailable. |
| INT lgpPwrStateOutputSource | 1.3.6.1.4.1.476.1.42.3.5.3.31 | INTEGER | read-only | The UPS's output power source (inverter, bypass, or none). NOTE: It is possible that the load still has power from the Maintenance Bypass. |
| INT lgpPwrStateInputSource | 1.3.6.1.4.1.476.1.42.3.5.3.32 | INTEGER | read-only | The system input power source (none, utility, generator). |
| INT lgpPwrStateInputQualification | 1.3.6.1.4.1.476.1.42.3.5.3.33 | INTEGER | read-only | The current state of the system input. The unit may or may not operate normally under 'marginalLow' and 'marginalHigh' states. |
| INT lgpPwrStateBypassStaticSwitchState | 1.3.6.1.4.1.476.1.42.3.5.3.34 | INTEGER | read-only | The current state of the bypass static switch. |
| INT lgpPwrStateBypassQualification | 1.3.6.1.4.1.476.1.42.3.5.3.35 | INTEGER | read-only | The current operational state of the bypass static switch. The unit may or may not operate normally under 'marginalLow' and 'marginalHigh' states. |
| INT lgpPwrStateDCBusQualification | 1.3.6.1.4.1.476.1.42.3.5.3.36 | INTEGER | read-only | The current operational state of the DC bus. The unit may or may not operate normally under 'marginalLow' and 'marginalHigh' states. |
| INT lgpPwrStateOutQualification | 1.3.6.1.4.1.476.1.42.3.5.3.37 | INTEGER | read-only | The current operational state of the output. The unit may or may not operate normally under 'marginalLow' and 'marginalHigh' states. |
| INT lgpPwrStateInverterQualification | 1.3.6.1.4.1.476.1.42.3.5.3.38 | INTEGER | read-only | The current operational state of the inverter. The unit may or may not operate normally under 'marginalLow' and 'marginalHigh' states. |
| INT lgpPwrStateInverterState | 1.3.6.1.4.1.476.1.42.3.5.3.39 | INTEGER | read-only | The current state of the inverter. |
| INT lgpPwrStateRectifierState | 1.3.6.1.4.1.476.1.42.3.5.3.40 | INTEGER | read-only | The current state of the rectifier. |
| lgpPwrStateModuleGroup | 1.3.6.1.4.1.476.1.42.3.5.3.41 | This group contains UPS module information. | ||
| I32 lgpPwrStateUpsModuleCount | 1.3.6.1.4.1.476.1.42.3.5.3.41.1 | Integer32 | read-write | Number of UPS modules in the system. In a single module system, this value is one. |
| I32 lgpPwrStateUpsModuleRedundantCount | 1.3.6.1.4.1.476.1.42.3.5.3.41.2 | Integer32 | read-only | Number of redundant UPS modules in the system. In a single module system, the value is zero. This value is dependent upon the present load and the number of modules (i.e. the value may change during normal operation based upon a load change). This value represents the number of extra modules above the minimum needed to support the load. |
| INT lgpPwrStateBackfeedBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.42 | INTEGER | read-only | The state of the Static Bypass Switch Line Disconnect Breaker. |
| INT lgpPwrStateLoadDisconnectState | 1.3.6.1.4.1.476.1.42.3.5.3.43 | INTEGER | read-only | The state of the Static Bypass Switch Load Disconnect Breaker. |
| INT lgpPwrStateInputBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.44 | INTEGER | read-only | The state of the Input Disconnect Breaker. |
| INT lgpPwrStateTrapFilterBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.45 | INTEGER | read-only | The state of the Trap Filter Disconnect Breaker. |
| INT lgpPwrStateInvOutputBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.46 | INTEGER | read-only | The state of the Inverter Output Disconnect Breaker. |
| INT lgpPwrStateIntBypassBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.47 | INTEGER | read-only | The state of the Internal Bypass Breaker. |
| INT lgpPwrStateBypassIsolBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.48 | INTEGER | read-only | The state of the Bypass Isolation Breaker. |
| INT lgpPwrStateRectifierIsolBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.49 | INTEGER | read-only | The state of the Rectifier Isolation Breaker. |
| INT lgpPwrStateMaintBypassBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.50 | INTEGER | read-only | The state of the Maintenance Bypass Breaker. |
| INT lgpPwrStateMaintIsolBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.51 | INTEGER | read-only | The state of the Maintenance Isolation Breaker. |
| INT lgpPwrStateOutStaticSwState | 1.3.6.1.4.1.476.1.42.3.5.3.52 | INTEGER | read-only | The state of the Output Series Static Switch. |
| INT lgpPwrStateModuleOutBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.53 | INTEGER | read-only | The state of the Module Output Breaker. |
| I32 lgpPwrBypassReXfrRemainTime | 1.3.6.1.4.1.476.1.42.3.5.3.54 | Integer32 | read-only | The time remaining before an inverter overload or inverter fault can be cleared and auto retransfer from the bypass to the inverter can take place. Note: If an inverter overload or fault is not taking place, this point will return 65535. |
| INT lgpPwrStateUpsOutputSource | 1.3.6.1.4.1.476.1.42.3.5.3.55 | INTEGER | read-only | The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker. NOTE: In a single-module system, this point is intended to have the same behavior as the RFC1628 point upsOutputSource. |
| INT lgpPwrStateLoadBusSynchronization | 1.3.6.1.4.1.476.1.42.3.5.3.56 | INTEGER | read-only | The state of the Load Bus Synchronizer (LBS). |
| lgpPwrStateCircuitBrkrStateGroup | 1.3.6.1.4.1.476.1.42.3.5.3.57 | This group contains Static Switch circuit breaker state information. | ||
| INT lgpPwrStateSource1InputBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.57.1 | INTEGER | read-only | The states of Source 1 Input Breaker. |
| INT lgpPwrStateSource2InputBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.57.2 | INTEGER | read-only | The states of Source 2 Input Breaker. |
| INT lgpPwrStateSource1BypassBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.57.3 | INTEGER | read-only | The states of Source 1 Bypass Breaker. |
| INT lgpPwrStateSource2BypassBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.57.4 | INTEGER | read-only | The states of Source 2 Bypass Breaker. |
| INT lgpPwrStateOutputBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.57.5 | INTEGER | read-only | The states of Output Breaker. |
| INT lgpPwrStateAuxOutputBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.57.6 | INTEGER | read-only | The states of Auxiliary Output Breaker. |
| INT lgpPwrStateSource1PduInputBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.57.7 | INTEGER | read-only | The states of Source 1 PDU Input Breaker. |
| INT lgpPwrStateSource2PduInputBrkrState | 1.3.6.1.4.1.476.1.42.3.5.3.57.8 | INTEGER | read-only | The states of Source 2 PDU Input Breaker. |
| INT lgpPwrEconomicOperation | 1.3.6.1.4.1.476.1.42.3.5.3.58 | INTEGER | read-only | The present state of ECO mode operation, on(1) if system is on bypass due to ECO mode operation, off(0) any other time. |
| lgpPwrSettings | 1.3.6.1.4.1.476.1.42.3.5.4 | This sub-tree registers Liebert Power Static Switch object identifiers. | ||
| OID lgpPwrPreferredSource | 1.3.6.1.4.1.476.1.42.3.5.4.1 | OBJECT IDENTIFIER | read-only | The well known measurement source from the 'lgpPwrWellKnownMeasurements' sub-tree that is the preferred input source of the system. |
| OID lgpPwrLoadOnSource | 1.3.6.1.4.1.476.1.42.3.5.4.2 | OBJECT IDENTIFIER | read-only | The well known measurement source from the 'lgpPwrWellKnownMeasurements' sub-tree that is currently powering the output (load). |
| I32 lgpPwrNominalVoltageDeviation | 1.3.6.1.4.1.476.1.42.3.5.4.3 | Integer32 | read-only | The nominal voltage deviation between the well known measurement source lgpPwrSource1Input and lgpPwrSource2Input. |
| I32 lgpPwrNominalVoltageDeviationPercent | 1.3.6.1.4.1.476.1.42.3.5.4.4 | Integer32 | read-only | The percentage of the nominal voltage deviation between the well known measurement source lgpPwrSource1Input and lgpPwrSource2Input. |
| I32 lgpPwrPhaseDifferenceLimit | 1.3.6.1.4.1.476.1.42.3.5.4.5 | Integer32 | read-only | The maximum phase difference (between the well known input sources ) in which a transfer to an available input source is permitted. |
| I32 lgpPwrFrequencyDeviationLimit | 1.3.6.1.4.1.476.1.42.3.5.4.6 | Integer32 | read-only | The maximum frequency deviation (between the well known input sources ) in which a transfer to an available input source is permitted. |
| lgpPwrThresholdTable | 1.3.6.1.4.1.476.1.42.3.5.4.7 | not-accessible | A list of power thresholds for a given power measurement at a point/location in the system. The lgpPwrThresholdType in this table corresponds to the type of measurement the high and low thresholds applies to. This table contains zero, one, or many rows, depending upon the number of 'lgpPwrThresholdPoint' and 'lgpPwrThresholdSubID' available in the table. The NMS cannot create or delete rows from the table. The rows are created by the agent based upon the capabilities of the managed device. | |
| lgpPwrThresholdEntry | 1.3.6.1.4.1.476.1.42.3.5.4.7.1 | not-accessible | This entry defines the contents of the columns for the table 'lgpPwrThresholdTable'. | |
| U32 lgpPwrThresholdIndex | 1.3.6.1.4.1.476.1.42.3.5.4.7.1.1 | Unsigned32 | not-accessible | This is the index indicating the row of the table 'lgpPwrLineMeasurementTable' for a power measurement point. |
| OID lgpPwrThresholdPoint | 1.3.6.1.4.1.476.1.42.3.5.4.7.1.2 | OBJECT IDENTIFIER | read-only | An OID representing a well known measurement point. These object identifiers indicate a point or location of power measurement in a power system. The OID's name usually implies a location of the measurement point such as 'input', 'output', 'bypass' etc. |
| U32 lgpPwrThresholdSubID | 1.3.6.1.4.1.476.1.42.3.5.4.7.1.3 | Unsigned32 | read-only | This is a sub identifier for the 'lgpPwrThresholdPoint'. It indicates the instance number of the well known threshold point. |
| OID lgpPwrThresholdType | 1.3.6.1.4.1.476.1.42.3.5.4.7.1.4 | OBJECT IDENTIFIER | read-only | An OID representing a well known measurement type. These object identifiers indicate the type of measurement referenced by the row of the table. These object identifiers can encompass units of measure, lines of reference, and device location. The OID's name usually implies a measurement type such as 'voltsAc', 'current', 'voltsDc', 'VoltsLL', etc. |
| I32 lgpPwrThresholdHighWarning | 1.3.6.1.4.1.476.1.42.3.5.4.7.1.5 | Integer32 | read-write | The high warning threshold of a type of measurement designated by the 'lgpPwrThresholdType' at a location designated by the 'lgpPwrThresholdPoint'. If multiple thresholds are available at a single 'lgpPwrThresholdPoint', of the same 'lgpPwrThresholdType', then the 'lgpPwrThresholdSubID' will differentiate between them. When this threshold is met, the agent will send a notification. |
| I32 lgpPwrThresholdHighFailure | 1.3.6.1.4.1.476.1.42.3.5.4.7.1.6 | Integer32 | read-write | The high failure threshold of a type of measurement designated by the 'lgpPwrThresholdType' at a location designated by the 'lgpPwrThresholdPoint'. If multiple thresholds are available at a single 'lgpPwrThresholdPoint', of the same 'lgpPwrThresholdType', then the 'lgpPwrThresholdSubID' will differentiate between them. When this threshold is met, the agent will send a notification. |
| I32 lgpPwrThresholdLowWarning | 1.3.6.1.4.1.476.1.42.3.5.4.7.1.7 | Integer32 | read-write | The low warning threshold of a type of measurement designated by the 'lgpPwrThresholdType' at a location designated by the 'lgpPwrThresholdPoint'. If multiple thresholds are available at a single 'lgpPwrThresholdPoint', of the same 'lgpPwrThresholdType', then the 'lgpPwrThresholdSubID' will differentiate between them. When this threshold is met, the agent will send a notification. |
| I32 lgpPwrThresholdLowFailure | 1.3.6.1.4.1.476.1.42.3.5.4.7.1.8 | Integer32 | read-write | The low failure threshold of a type of measurement designated by the 'lgpPwrThresholdType' at a location designated by the 'lgpPwrThresholdPoint'. If multiple thresholds are available at a single 'lgpPwrThresholdPoint', of the same 'lgpPwrThresholdType', then the 'lgpPwrThresholdSubID' will differentiate between them. When this threshold is met, the agent will send a notification. |
| INT lgpPwrUpsAutoRestart | 1.3.6.1.4.1.476.1.42.3.5.4.8 | INTEGER | read-write | The device will automatically restart when utility power is restored following a battery discharge. |
| I32 lgpPwrUpsAutoRestartDelay | 1.3.6.1.4.1.476.1.42.3.5.4.9 | Integer32 | read-write | The device will automatically delay a certain number of seconds and then restart after utility power is restored following a battery discharge. The number of seconds to delay is subject to the precision of the device and should be kept to 10 second intervals. |
| I32 lgpPwrAutoRestartBatteryChargeThreshold | 1.3.6.1.4.1.476.1.42.3.5.4.10 | Integer32 | read-write | The battery charge percentage required before the device can automatically restart. |
| I32 lgpPwrParallelModuleCount | 1.3.6.1.4.1.476.1.42.3.5.4.11 | Integer32 | read-write | The number of modules in the parallel system. |
| I32 lgpPwrParallelRedundancyCount | 1.3.6.1.4.1.476.1.42.3.5.4.12 | Integer32 | read-write | The number of redundant modules in the parallel system. |
| INT lgpPwrLoadBusSyncMode | 1.3.6.1.4.1.476.1.42.3.5.4.13 | INTEGER | read-write | The configuration of Load Bus Synchronization (LBS) between independent systems. |
| INT lgpPwrEconomicOperationMode | 1.3.6.1.4.1.476.1.42.3.5.4.14 | INTEGER | read-write | The configuration of the economic operation mode of the system. |
| INT lgpPwrAutomaticBatteryTest | 1.3.6.1.4.1.476.1.42.3.5.4.15 | INTEGER | read-write | Automatic battery test option. If enabled, the battery will be tested on a fixed interval. If disabled, the battery test must be initiated by a battery test command. The interval at which a battery test is performed is defined by 'lgpPwrAutomaticBatteryTestInterval'. |
| I32 lgpPwrMinimumRedundantPowerModule | 1.3.6.1.4.1.476.1.42.3.5.4.16 | Integer32 | read-write | The minimum number of redundant power modules that must be present before sending a loss of power redundancy alarm. If 0, there is no redundant power functionality. |
| I32 lgpPwrMinimumRedundantBatteryModule | 1.3.6.1.4.1.476.1.42.3.5.4.17 | Integer32 | read-write | The minimum number of redundant battery modules that must be present before sending an alarm. If 0, the redundant battery module alarm is disabled. |
| I32 lgpPwrOutputToLoadUserOverloadLimit | 1.3.6.1.4.1.476.1.42.3.5.4.18 | Integer32 | read-write | This is the user specified maximum load the device can support without sending an alarm. |
| I32 lgpPwrNoLoadWarningLimit | 1.3.6.1.4.1.476.1.42.3.5.4.19 | Integer32 | read-write | The minimum current draw on the output in which the device considers there to be a load present on the output. The condition lgpConditionWarningNoLoadDetected will be triggered if the output current falls below this value. If this value is '-1' then the lgpConditionNoLoadDetectedWarning condition is 'disabled'. |
| I32 lgpPwrNoLoadWarningDelay | 1.3.6.1.4.1.476.1.42.3.5.4.20 | Integer32 | read-write | The amount of time to delay before annunciation of the condition lgpConditionNoLoadDetectedWarning after the output current load falls below the threshold lgpPwrOutputNoLoadWarningLimit. |
| INT lgpPwrEconomicOperationModeControl | 1.3.6.1.4.1.476.1.42.3.5.4.21 | INTEGER | read-write | The configuration of the economic operation mode of the system. Note that this supersedes lgpPwrEconomicOperationMode in newer devices. |
| lgpPwrConversion | 1.3.6.1.4.1.476.1.42.3.5.5 | This sub-tree is used to register Liebert Power Conversion object identifiers. | ||
| I32 lgpPwrNumberInstalledPowerModules | 1.3.6.1.4.1.476.1.42.3.5.5.1 | Integer32 | read-only | The number of power modules installed in the device. |
| I32 lgpPwrNumberFailedPowerModules | 1.3.6.1.4.1.476.1.42.3.5.5.2 | Integer32 | read-only | The number of power modules in the device that have failed. |
| I32 lgpPwrNumberRedundantPowerModules | 1.3.6.1.4.1.476.1.42.3.5.5.3 | Integer32 | read-only | The number of redundant power modules installed in the device. |
| I32 lgpPwrNumberActivePowerModules | 1.3.6.1.4.1.476.1.42.3.5.5.4 | Integer32 | read-only | The number of active power modules in the device. |
| I32 lgpPwrNumberPowerModuleWarnings | 1.3.6.1.4.1.476.1.42.3.5.5.6 | Integer32 | read-only | The number of power modules in the device that have a warning. |
| INT lgpPwrUpsInverterStandby | 1.3.6.1.4.1.476.1.42.3.5.5.7 | INTEGER | read-write | The output to the load is supported by the bypass and the inverter is on standby. |
| lgpPwrControl | 1.3.6.1.4.1.476.1.42.3.5.6 | This sub-tree is used to register Liebert Power Control object identifiers. | ||
| lgpPwrWellKnownControlPoints | 1.3.6.1.4.1.476.1.42.3.5.6.1 | This sub-tree registers well known Liebert Power Control Points. The object identifier names usually imply locations where control of a device is available -- such 'output' or 'load circuits'. | ||
| lgpPwrLoadCircuit | 1.3.6.1.4.1.476.1.42.3.5.6.1.1 | The managed device's controllable load circuit. Many power systems contain more than one load circuit. This identifier represents one load circuit for the system but does not necessarily represent the 'first' one. The load circuits' numbering with respect to 'lgpPwrLoadCircuit1' etc. may depend on the physical wiring of the system when it was installed. | ||
| lgpPwrLoadCircuitTable | 1.3.6.1.4.1.476.1.42.3.5.6.2 | not-accessible | A list of load circuits that can be controlled(opened or closed). The NMS cannot create or delete rows from the table. The rows are created by the agent based upon the capabilities of the managed device. | |
| lgpPwrLoadCircuitEntry | 1.3.6.1.4.1.476.1.42.3.5.6.2.1 | not-accessible | This entry defines the contents of the columns for the table 'lgpPwrLoadCircuitTable'. | |
| U32 lgpPwrLoadCircuitIndex | 1.3.6.1.4.1.476.1.42.3.5.6.2.1.1 | Unsigned32 | not-accessible | This is the index indicating the row of the table 'lgpPwrLoadCircuitTable'. |
| OID lgpPwrLoadCircuitId | 1.3.6.1.4.1.476.1.42.3.5.6.2.1.2 | OBJECT IDENTIFIER | read-only | An OID representing a well known load circuit identifier. These load circuit identifiers indicate the name or type of load circuit reference in the table. |
| U32 lgpPwrLoadCircuitSubID | 1.3.6.1.4.1.476.1.42.3.5.6.2.1.3 | Unsigned32 | read-only | This is a sub identifier for the 'lgpPwrLoadCircuitId'. It indicates the hardware identifier of the load control circuit. |
| INT lgpPwrLoadCircuitState | 1.3.6.1.4.1.476.1.42.3.5.6.2.1.4 | INTEGER | read-write | This identifier indicates the state of the load circuit. When read, only a closed or open response will be returned. When written to, the state of the circuit will transition to desired state. |
| INT lgpPwrLoadCircuitStateAndControl | 1.3.6.1.4.1.476.1.42.3.5.6.2.1.5 | INTEGER | read-write | This identifier indicates the state of the load circuit. When read, only a closed or open response will be returned. When written to, the state of the circuit will transition to desired state. |
| I32 lgpPwrAlarmSilence | 1.3.6.1.4.1.476.1.42.3.5.6.3 | Integer32 | read-write | Audible Alarm Silence Command. This command turns off the device's audible alarm. It will not affect the status of the alarm(s) that caused the audible alarm. This command should be sent with a parameter of 1. This variable doesn't return a value when read. |
| INT lgpPwrBatteryTest | 1.3.6.1.4.1.476.1.42.3.5.6.4 | INTEGER | read-write | Battery Test Command. This command will initiate a battery test if one is not already in progress, or abort the current test if it is in progress. |
| I32 lgpPwrUpsAbortCommand | 1.3.6.1.4.1.476.1.42.3.5.6.5 | Integer32 | read-write | UPS Abort command. This command will abort the pending command on the device. There is no guarantee a client using the abort command will cancel a command sent moments before from the same client. Another client could initiate a command and change what command is actually pending on the device. This command should be sent with a parameter of 1. This variable doesn't return a value when read. |
| I32 lgpPwrTransferToBypass | 1.3.6.1.4.1.476.1.42.3.5.6.6 | Integer32 | read-write | Transfer to Bypass Command. This command will initiate a transfer of the load to the bypass of the system. This command should be sent with a parameter of 1. This variable doesn't return a value when read. |
| I32 lgpPwrTransferToInverter | 1.3.6.1.4.1.476.1.42.3.5.6.7 | Integer32 | read-write | Transfer to Inverter Command. This command will initiate a transfer of the load to the inverter of the system. This command should be sent with a parameter of 1. This variable doesn't return a value when read. |
| I32 lgpPwrOutputOnDelay | 1.3.6.1.4.1.476.1.42.3.5.6.8 | Integer32 | read-write | Output On Delay Command. This command will turn on the output of the device after a user specified delay. The number of seconds to delay is subject to the precision of the device and should be kept to 10 second intervals. |
| I32 lgpPwrOutputOffDelayWithRestart | 1.3.6.1.4.1.476.1.42.3.5.6.9 | Integer32 | read-write | Output Off Delay with Restart Command. This command will turn off the output of the device after a user specified delay. The number of seconds to delay is subject to the precision of the device and should be kept to 10 second intervals. The device will then turn the output on again after a specified amount of time. |
| I32 lgpPwrOutputOffDelayWithoutRestart | 1.3.6.1.4.1.476.1.42.3.5.6.10 | Integer32 | read-write | Output Off Delay without Restart Command. This command will turn off the output of the device after a specified delay. The number of seconds to delay is subject to the precision of the device and should be kept to 10 second intervals. The device will NOT automatically turn the output on following this command. |
| lgpPwrTopology | 1.3.6.1.4.1.476.1.42.3.5.7 | This sub-tree is used to register Liebert Power Topology object identifiers. | ||
| INT lgpPwrUpsTopOffline | 1.3.6.1.4.1.476.1.42.3.5.7.1 | INTEGER | read-only | The UPS has an offline topology. Under normal operating conditions, AC power from the utility passes straight through the UPS to the critical load. The inverter is used to convert the DC power from the battery to create AC power to support the load when the utility fails. Normally the inverter is operating in the stand-by mode, keeping the batteries charged. Should the utility power go out of specification, the inverter will power the load by drawing energy from the battery. |
| INT lgpPwrUpsTopLineInteractive | 1.3.6.1.4.1.476.1.42.3.5.7.2 | INTEGER | read-only | The UPS has a line-interactive topology. This topology resembles the offline product, but inserts a transformer or inductor in series between the utility power source and the load. This inline inductor enables the UPS inverter to interact with incoming power and provide a measure of power conditioning to the load. This buck-and-boost circuitry helps with high and low input voltage conditions. |
| INT lgpPwrUPSTopDualInput | 1.3.6.1.4.1.476.1.42.3.5.7.3 | INTEGER | read-only | The system has separate input sources for the bypass and inverter. |
| INT lgpPwrTopFrequencyConverter | 1.3.6.1.4.1.476.1.42.3.5.7.4 | INTEGER | read-only | The system has a frequency converter. |
| INT lgpPwrTopVoltageConverter | 1.3.6.1.4.1.476.1.42.3.5.7.5 | INTEGER | read-only | The system has a voltage converter. |
| I32 lgpPwrTopMaximumFrameCapacity | 1.3.6.1.4.1.476.1.42.3.5.7.6 | Integer32 | read-write | The maximum device system capacity. |
| INT lgpPwrTopRedundantControlModules | 1.3.6.1.4.1.476.1.42.3.5.7.7 | INTEGER | read-only | The device has a redundant control module installed. |
| INT lgpPwrInputIsolationTransformerInstalled | 1.3.6.1.4.1.476.1.42.3.5.7.8 | INTEGER | read-only | Indicates whether the input isolation transformer is installed. |
| INT lgpPwrStateStaticSwitchType | 1.3.6.1.4.1.476.1.42.3.5.7.9 | INTEGER | read-only | Static switch type (N/A, continous duty, or momentary duty). |
| INT lgpPwrStateModuleType | 1.3.6.1.4.1.476.1.42.3.5.7.10 | INTEGER | read-only | UPS module type. SMS -- Single Module System 1 + 1 -- Redundant system for capacity 1 + N -- Distributed multi-module system N + 1 -- A multi-module system with one bypass for the system SCC -- System Control Cabinet used in an N+1 system to provide a single bypass for the system. MSS -- Main Static Switch |
| INT lgpPwrStateBypassInputConfig | 1.3.6.1.4.1.476.1.42.3.5.7.11 | INTEGER | read-only | Bypass input wire physical wiring configuration. singlePhase2WireL1WithReturn Single phase input with 2 wires (Line 1, and Return). twoPhase2WireL1L2 Two phase input with 2 wires (Line 1, and Line 2). twoPhase3WireL1L2WithNeutral Two phase input with 3 wires (Line 1, Line 2, and Neutral) threePhase3WireL1L2L3 Three phase input with 3 wires (Line 1, Line 2, and Line 3) threePhase4WireL1L2L3WithNeutral Three phase input with 4 wires (Line 1, Line 2, Line 3, and Neutral). |
| INT lgpPwrStateOutputConfig | 1.3.6.1.4.1.476.1.42.3.5.7.12 | INTEGER | read-only | Output wire physical wiring configuration. singlePhase2WireL1WithReturn Single phase output with 2 wires (Line 1, and Return). twoPhase2WireL1L2 Two phase output with 2 wires (Line 1, and Line 2). twoPhase3WireL1L2WithNeutral Two phase output with 3 wires (Line 1, Line 2, and Neutral) threePhase3WireL1L2L3 Three phase output with 3 wires (Line 1, Line 2, and Line 3) threePhase4WireL1L2L3WithNeutral Three phase output with 4 wires (Line 1, Line 2, Line 3, and Neutral). |
| INT lgpPwrRectifierPassiveFilterInstalled | 1.3.6.1.4.1.476.1.42.3.5.7.13 | INTEGER | read-only | Indicates whether the rectifier passive filter is installed. |
| INT lgpPwrRectifierTrapInstalled | 1.3.6.1.4.1.476.1.42.3.5.7.14 | INTEGER | read-only | Indicates whether the rectifier input passive filter is installed. |
| INT lgpPwrRectifierActiveFilterInstalled | 1.3.6.1.4.1.476.1.42.3.5.7.15 | INTEGER | read-only | Indicates whether the rectifier active filter is installed. |
| lgpPwrStatistic | 1.3.6.1.4.1.476.1.42.3.5.8 | This sub-tree is used to register Liebert Power Statistic object identifiers. | ||
| I32 lgpPwrBrownOutCount | 1.3.6.1.4.1.476.1.42.3.5.8.1 | Integer32 | read-only | The number of occurrences where the input line voltage has fallen below a pre-determined threshold for a specified amount of time. This number resets when the command 'lgpPwrStatisticsReset' is executed. |
| I32 lgpPwrBlackOutCount | 1.3.6.1.4.1.476.1.42.3.5.8.2 | Integer32 | read-only | The number of occurrences where there is a total loss of electric power. This number resets when the command 'lgpPwrStatisticsReset' is executed. |
| I32 lgpPwrTransientCount | 1.3.6.1.4.1.476.1.42.3.5.8.3 | Integer32 | read-only | The number of occurrences where the input line voltage spikes above a pre-determined threshold for a specified amount of time. This number resets when the command 'lgpPwrStatisticsReset' is executed. |
| I32 lgpPwrBatteryDischargeCount | 1.3.6.1.4.1.476.1.42.3.5.8.4 | Integer32 | read-only | The number of battery discharges since the last reset. |
| I32 lgpPwrBatteryDischargeTime | 1.3.6.1.4.1.476.1.42.3.5.8.5 | Integer32 | read-only | The total accumulated time spent on battery since the last reset. |
| I32 lgpPwrBatteryAmpHours | 1.3.6.1.4.1.476.1.42.3.5.8.6 | Integer32 | read-only | The total accumulated Amp-hours removed from the battery since last reset. |
| I32 lgpPwrBatteryWattHours | 1.3.6.1.4.1.476.1.42.3.5.8.7 | Integer32 | read-only | The total accumulated Watt-Hours removed from the battery since last reset. This command should be sent with a parameter of 1. This variable doesn't return a value when read. |
| I32 lgpPwrBatteryStatisticsReset | 1.3.6.1.4.1.476.1.42.3.5.8.8 | Integer32 | read-write | Battery statistics clear command. The command to reset all battery statistics stored by the device. This command should be sent with a parameter of 1. This variable doesn't return a value when read. |
| I32 lgpPwrStatisticsReset | 1.3.6.1.4.1.476.1.42.3.5.8.9 | Integer32 | read-write | Reset Power Statistics Command. This command will reset the power statistics stored in the system. This command should be sent with a parameter of 1. This variable doesn't return a value when read. |
| lgpPwrConfig | 1.3.6.1.4.1.476.1.42.3.5.9 | This sub-tree is used to register Liebert Power Configuration Object identifiers. | ||
| I32 lgpPwrSysCapacity | 1.3.6.1.4.1.476.1.42.3.5.9.1 | Integer32 | read-write | The current device system capacity. |
| INT lgpPwrUPSModuleMode | 1.3.6.1.4.1.476.1.42.3.5.9.2 | INTEGER | read-write | The module mode of the UPS. |
| I32 lgpPwrMaxRatedCurrent | 1.3.6.1.4.1.476.1.42.3.5.9.3 | Integer32 | read-only | System output maximum amperage rating. The maximum rated amperage for the system. This value is based upon the model type and is typically limited by the wiring, breakers, power devices, etc. |
| INT lgpPwrRectifierPulseCount | 1.3.6.1.4.1.476.1.42.3.5.9.4 | INTEGER | read-only | Rectifier pulse count per waveform cycle (6-, 12-, 18-, or 24-pulse). |
RFC description
Liebert power management MIB for UPS, battery, and power monitoring in data center infrastructure.
Start monitoring Liebert/Vertiv UPS/PDU and power-conditioning equipment (battery health) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.