EATON-ATS2-MIB

All MIBs › EATON-ATS2-MIB

Organization: Eaton Corporation

Last Updated: 2014-07-31

Category: Domain: Power/UPS, Vendor: Eaton

Description: Eaton Automatic Transfer Switch (ATS2) MIB for monitoring transfer switch status, input sources, and load parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is EATON-ATS2-MIB?

EATON-ATS2-MIB is Eaton's vendor-specific SNMP module for its Automatic Transfer Switch (ATS) product line, used in data center and facility power distribution to switch a load between two power sources. It exposes identity data (manufacturer, model, firmware version, serial and part number, agent version) alongside operational measurement and status objects covering input power sources and the current transfer/operation mode. Its core monitoring value is hardware/power status: it reports each input source's phase/dephasing condition through ats2InputTable/ats2InputEntry, the overall ats2OperationMode (which source is feeding the load), and general device status via the ats2Status group -- effectively a power-hardware health check rather than a compute/software one. It is a self-contained enterprise MIB but is typically deployed alongside standard power/UPS MIBs and monitored through general-purpose network management systems via SNMP. It is deployed in data centers, telecom facilities, and critical infrastructure sites where an ATS provides automatic failover between utility and backup power feeds. Engineers can download the EATON-ATS2-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in EATON-ATS2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Eaton Automatic Transfer Switch (ATS2)

Monitoring Examples

An administrator polls ats2InputTable/ats2InputEntry to check ats2InputDephasing on each incoming power leg, catching a phase misalignment before it causes a failed transfer. Watching ats2OperationMode reveals whether the ATS is currently on the primary or backup source, and an unexpected mode change can indicate a utility power event. The ats2Ident objects (ats2IdentFWVersion, ats2IdentSerialNumber) are polled during audits to confirm firmware consistency and asset identity across a fleet of ATS units, while ats2Status/ats2Measure groups provide the general health and electrical measurements of the switch.

What Can Be Monitored

input source dephasing/status
active power source / transfer mode
firmware version
serial and part number
general device status
power measurements

Imported Objects

From EATON-OIDS

sts	OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using ats2InputDephasing OID:

Select an Eaton automatic transfer switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ats2InputDephasing into the Find box to locate it in the OID tree, then select it and click OK. The dephasing in between Source 1 and Source 2. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value drifts significantly from its normal baseline, since an unexpected change often points to a real underlying issue. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ats2	1.3.6.1.4.1.534.10.2			The MIB module for Eaton ATS (Automatic Transfer Switch).
ats2Ident	1.3.6.1.4.1.534.10.2.1
STR ats2IdentManufacturer	1.3.6.1.4.1.534.10.2.1.1	DisplayString	read-only	The manufacturer name.
STR ats2IdentModel	1.3.6.1.4.1.534.10.2.1.2	DisplayString	read-only	Device model name.
STR ats2IdentFWVersion	1.3.6.1.4.1.534.10.2.1.3	DisplayString	read-only	Device F/W version.
STR ats2IdentRelease	1.3.6.1.4.1.534.10.2.1.4	DisplayString	read-only	The released date.
STR ats2IdentSerialNumber	1.3.6.1.4.1.534.10.2.1.5	DisplayString	read-only	Device serial number
STR ats2IdentPartNumber	1.3.6.1.4.1.534.10.2.1.6	DisplayString	read-only	Device part number
STR ats2IdentAgentVersion	1.3.6.1.4.1.534.10.2.1.7	DisplayString	read-only	Communication Card F/W version
ats2Measure	1.3.6.1.4.1.534.10.2.2
ats2Input	1.3.6.1.4.1.534.10.2.2.1
INT ats2InputDephasingEx	1.3.6.1.4.1.534.10.2.2.1.1	INTEGER	read-only	The dephasing in between Source 1 and Source 2.
ats2InputTable	1.3.6.1.4.1.534.10.2.2.2		not-accessible	The table of input information.
ats2InputEntry	1.3.6.1.4.1.534.10.2.2.2.1		not-accessible	The input information of each source input: .1 source1 .2 source2
INT ats2InputIndex	1.3.6.1.4.1.534.10.2.2.2.1.1	INTEGER	read-only	Index to input.
INT ats2InputVoltage	1.3.6.1.4.1.534.10.2.2.2.1.2	INTEGER	read-only	The input voltage in front of relay. Units are 0.1 V.
INT ats2InputFrequency	1.3.6.1.4.1.534.10.2.2.2.1.3	INTEGER	read-only	The input frequency. Units are 0.1 Hz.
ats2Output	1.3.6.1.4.1.534.10.2.2.3
INT ats2OutputVoltage	1.3.6.1.4.1.534.10.2.2.3.1	INTEGER	read-only	The output voltage. Units are 0.1 V.
INT ats2OutputCurrent	1.3.6.1.4.1.534.10.2.2.3.2	INTEGER	read-only	The output current. Units are 0.1 A.
INT ats2OperationMode	1.3.6.1.4.1.534.10.2.2.4	INTEGER	read-only	The operation mode.
ats2Status	1.3.6.1.4.1.534.10.2.3
ats2InputStatus	1.3.6.1.4.1.534.10.2.3.1
INT ats2InputStatusDephasing	1.3.6.1.4.1.534.10.2.3.1.1	INTEGER	read-only	The dephasing status in between Source 1 and Source 2.
ats2InputStatusTable	1.3.6.1.4.1.534.10.2.3.2		not-accessible	The table of input status.
ats2InputStatusEntry	1.3.6.1.4.1.534.10.2.3.2.1		not-accessible	The input flow status: .1 source1 .2 source2
INT ats2InputStatusIndex	1.3.6.1.4.1.534.10.2.3.2.1.1	INTEGER	read-only	Index of input entry.
INT ats2InputStatusFrequency	1.3.6.1.4.1.534.10.2.3.2.1.2	INTEGER	read-only	The status of input frequency.
INT ats2InputStatusGood	1.3.6.1.4.1.534.10.2.3.2.1.3	INTEGER	read-only	The summarized status of input AC flow.
INT ats2InputStatusInternalFailure	1.3.6.1.4.1.534.10.2.3.2.1.4	INTEGER	read-only	The internal fault status of input.
INT ats2InputStatusVoltage	1.3.6.1.4.1.534.10.2.3.2.1.5	INTEGER	read-only	The status of input voltage.
INT ats2InputStatusUsed	1.3.6.1.4.1.534.10.2.3.2.1.6	INTEGER	read-only	The status of input relay.
ats2OutputStatus	1.3.6.1.4.1.534.10.2.3.3
INT ats2StatusInternalFailure	1.3.6.1.4.1.534.10.2.3.3.1	INTEGER	read-only	Output fault.
INT ats2StatusOutput	1.3.6.1.4.1.534.10.2.3.3.2	INTEGER	read-only	Output powered status.
INT ats2StatusOverload	1.3.6.1.4.1.534.10.2.3.3.3	INTEGER	read-only	The output overload status.
INT ats2StatusOverTemperature	1.3.6.1.4.1.534.10.2.3.3.4	INTEGER	read-only	The over temperature status.
INT ats2StatusShortCircuit	1.3.6.1.4.1.534.10.2.3.3.5	INTEGER	read-only	Short circuit status.
INT ats2StatusCommunicationLost	1.3.6.1.4.1.534.10.2.3.3.6	INTEGER	read-only	Communication failure status.
INT ats2StatusConfigurationFailure	1.3.6.1.4.1.534.10.2.3.3.7	INTEGER	read-only	Configuration failure status.
ats2Config	1.3.6.1.4.1.534.10.2.4
ats2ConfigTime	1.3.6.1.4.1.534.10.2.4.1
UNI ats2ConfigTimeRTC	1.3.6.1.4.1.534.10.2.4.1.1	UnixTimeStamp	read-write	Clock value. This could be from either a real-time clock (in which case it is likely writeable) or from a time server via NTP (probably read-only). (since 1/1/1970 at 1:00:00).
STR ats2ConfigTimeTextDate	1.3.6.1.4.1.534.10.2.4.1.2	DisplayString	read-only	The present date in MM/DD/YYYY text format.
STR ats2ConfigTimeTextTime	1.3.6.1.4.1.534.10.2.4.1.3	DisplayString	read-only	The present time in hh:mm:ss text format.
INT ats2ConfigInputVoltageRating	1.3.6.1.4.1.534.10.2.4.2	INTEGER	read-only	The input voltage rating. Unit is 1 V.
INT ats2ConfigInputFrequencyRating	1.3.6.1.4.1.534.10.2.4.3	INTEGER	read-only	The input frequency rating. Unit is 1 Hz.
INT ats2ConfigOutputVoltage	1.3.6.1.4.1.534.10.2.4.4	INTEGER	read-write	The output voltage config. Unit is 1 V.
INT ats2ConfigPreferred	1.3.6.1.4.1.534.10.2.4.5	INTEGER	read-write	The preferred source.
INT ats2ConfigSensitivity	1.3.6.1.4.1.534.10.2.4.6	INTEGER	read-write	The AC Blackout Sensitivity.
INT ats2ConfigTransferMode	1.3.6.1.4.1.534.10.2.4.7	INTEGER	read-write	behavior configuration when transfering from one source to other source not synchronized.
INT ats2ConfigTransferTest	1.3.6.1.4.1.534.10.2.4.8	INTEGER	read-only	The status of transfer test.
INT ats2ConfigBrownoutLow	1.3.6.1.4.1.534.10.2.4.9	INTEGER	read-only	Setting of input brownout low voltage. Unit is 1 V.
INT ats2ConfigBrownoutLowDerated	1.3.6.1.4.1.534.10.2.4.10	INTEGER	read-only	Setting of input brownout low derated voltage. Unit is 1 V.
INT ats2ConfigBrownoutHigh	1.3.6.1.4.1.534.10.2.4.11	INTEGER	read-only	Setting of input brownout high voltage. Unit is 1 V.
INT ats2ConfigHysteresisVoltage	1.3.6.1.4.1.534.10.2.4.12	INTEGER	read-only	Hysteresis between loss point and comeback point. Unit is 1 V.
ats2Environment	1.3.6.1.4.1.534.10.2.5
INT ats2EnvRemoteTemp	1.3.6.1.4.1.534.10.2.5.1	INTEGER	read-only	The reading of an EMP's temperature sensor.
INT ats2EnvRemoteHumidity	1.3.6.1.4.1.534.10.2.5.2	INTEGER	read-only	The reading of an EMP's humidity sensor.
INT ats2EnvNumContacts	1.3.6.1.4.1.534.10.2.5.3	INTEGER	read-only	The number of Contacts in the ats2ContactSenseTable. This object indicates the number of rows in the ats2ContactSenseTable.
ats2ContactSenseTable	1.3.6.1.4.1.534.10.2.5.4		not-accessible	A list of Contact Sensing table entries. The number of entries is given by the value of ats2EnvNumContacts.
ats2ContactsTableEntry	1.3.6.1.4.1.534.10.2.5.4.1		not-accessible	An entry containing information applicable to a particular Contact input.
INT ats2ContactIndex	1.3.6.1.4.1.534.10.2.5.4.1.1	INTEGER	read-only	The Contact identifier; identical to the Contact Number. This object is not-accessible to MIB browsers, but had to be changed to read-only to satisfy SMIv2 syntax checkers if it is included in traps.
INT ats2ContactType	1.3.6.1.4.1.534.10.2.5.4.1.2	INTEGER	read-write	The normal state for this contact. The 'other' (not 'Normally') state is the Active state for generating the ats2tdContactActiveNotice trap. If anyChange(3) is selected, then this trap is sent any time the contact changes to either Open or Closed. No traps are sent if the Contact is set to notUsed(4). In many cases, the configuration for Contacts may be done by other means, so this object may be read-only.
INT ats2ContactState	1.3.6.1.4.1.534.10.2.5.4.1.3	INTEGER	read-only	The current state of the Contact input; the value is based on the open/closed input state and the setting for ats2ContactType. When entering the openWithNotice(3) and closedWithNotice(4) states, no entries added to the ats2AlarmTable, but the ats2tdContactActiveNotice trap is sent.
STR ats2ContactDescr	1.3.6.1.4.1.534.10.2.5.4.1.4	DisplayString	read-write	A label identifying the Contact. This object should be set by the administrator.
INT ats2EnvRemoteTempLowerLimit	1.3.6.1.4.1.534.10.2.5.5	INTEGER	read-write	The Lower Limit of the EMP temperature; if ats2EnvRemoteTemp falls below this value, the ats2RemoteTempBad alarm will occur.
INT ats2EnvRemoteTempUpperLimit	1.3.6.1.4.1.534.10.2.5.6	INTEGER	read-write	The Upper Limit of the EMP temperature; if ats2EnvRemoteTemp rises above this value, the ats2RemoteTempBad alarm will occur. This value should be greater than ats2EnvRemoteTempLowerLimit.
INT ats2EnvRemoteHumidityLowerLimit	1.3.6.1.4.1.534.10.2.5.7	INTEGER	read-write	The Lower Limit of the EMP humidity reading; if ats2EnvRemoteHumidity falls below this value, the ats2RemoteHumidityBad alarm will occur.
INT ats2EnvRemoteHumidityUpperLimit	1.3.6.1.4.1.534.10.2.5.8	INTEGER	read-write	The Upper Limit of the EMP humidity reading; if ats2EnvRemoteHumidity rises above this value, the ats2RemoteHumidityBad alarm will occur. This value should be greater than ats2EnvRemoteHumidityLowerLimit.
ats2Traps	1.3.6.1.4.1.534.10.2.10
NTF ats2TrapCommunicationLost	1.3.6.1.4.1.534.10.2.10.1			Communication with the ATS failed.
NTF ats2TrapCommunicationRecovered	1.3.6.1.4.1.534.10.2.10.2			Communication with the ATS recovered.
NTF ats2TrapOutputPowered	1.3.6.1.4.1.534.10.2.10.3			The ATS powers the load.
NTF ats2TrapOutputNotPowered	1.3.6.1.4.1.534.10.2.10.4			The ATS does not powers the load.
NTF ats2TrapOverload	1.3.6.1.4.1.534.10.2.10.5			The ATS has sensed a critical overload.
NTF ats2TrapNoOverLoad	1.3.6.1.4.1.534.10.2.10.6			The critical overload disappeared.
NTF ats2TrapInternalFailure	1.3.6.1.4.1.534.10.2.10.7			The ATS has an internal failure (sum of all HW internal failure).
NTF ats2TrapNoInternalFailure	1.3.6.1.4.1.534.10.2.10.8			The ATS internal failure disappeared.
NTF ats2TrapSource1Normal	1.3.6.1.4.1.534.10.2.10.9			Source 1 returns to normal.
NTF ats2TrapSource1OutOfRange	1.3.6.1.4.1.534.10.2.10.10			Source 1 out of range.
NTF ats2TrapSource2Normal	1.3.6.1.4.1.534.10.2.10.11			Source 2 returns to normal.
NTF ats2TrapSource2OutOfRange	1.3.6.1.4.1.534.10.2.10.12			Source 2 out of range.
NTF ats2TrapSourceDesynchronized	1.3.6.1.4.1.534.10.2.10.13			Source 1 and Source 2 phase are desynchronized.
NTF ats2TrapSourceSynchronized	1.3.6.1.4.1.534.10.2.10.14			Source 1 and Source 2 phase are synchronized.
NTF ats2TrapOutputPoweredBySource1	1.3.6.1.4.1.534.10.2.10.15			Source 1 powers the output.
NTF ats2TrapOutputPoweredBySource2	1.3.6.1.4.1.534.10.2.10.16			Source 2 powers the output.
NTF ats2TrapRemoteTempLow	1.3.6.1.4.1.534.10.2.10.20			The remote temperature, ats2EnvRemoteTemp, has fallen below the set lower limit, ats2EnvRemoteTempLowerLimit.
NTF ats2TrapRemoteTempHigh	1.3.6.1.4.1.534.10.2.10.21			The remote temperature, ats2EnvRemoteTemp, has risen above the set upper limit, xupsEnvRemoteTempUpperLimit.
NTF ats2TrapRemoteTempNormal	1.3.6.1.4.1.534.10.2.10.22			The remote temperature, ats2EnvRemoteTemp, is inside the interval defined by the lower limit and the upper limit.
NTF ats2TrapRemoteHumidityLow	1.3.6.1.4.1.534.10.2.10.23			The remote humidity, ats2EnvRemoteHumidity, has fallen below the set lower limit, ats2EnvRemoteHumidityLowerLimit.
NTF ats2TrapRemoteHumidityHigh	1.3.6.1.4.1.534.10.2.10.24			The remote humidity, ats2EnvRemoteHumidity, has risen above the set upper limit, ats2EnvRemoteHumidityUpperLimit.
NTF ats2TrapRemoteHumidityNormal	1.3.6.1.4.1.534.10.2.10.25			The remote humidity, ats2EnvRemoteHumidity, is inside the interval defined by the lower limit and the upper limit.
NTF ats2Contact1ActiveNotice	1.3.6.1.4.1.534.10.2.10.26			The Contact 1 is in its Active state. The following are the situations that generate this trap: For ats2ContactType: and ats2ContactState: normallyOpen(1) and closedWithNotice(4) normallyClosed(2) and openWithNotice(3) anyChange(3) and openWithNotice(3) or closedWithNotice(4)
NTF ats2Contact1InactiveNotice	1.3.6.1.4.1.534.10.2.10.27			The Contact 1 has changed to its Inactive state.
NTF ats2Contact2ActiveNotice	1.3.6.1.4.1.534.10.2.10.28			The Contact 2 is in its Active state. The following are the situations that generate this trap: For ats2ContactType: and ats2ContactState: normallyOpen(1) and closedWithNotice(4) normallyClosed(2) and openWithNotice(3) anyChange(3) and openWithNotice(3) or closedWithNotice(4)
NTF ats2Contact2InactiveNotice	1.3.6.1.4.1.534.10.2.10.29			The Contact 2 has changed to its Inactive state.
NTF ats2TestTrap	1.3.6.1.4.1.534.10.2.10.40			Sent whenever the trap test feature is used by the communication card.

RFC description

Eaton Automatic Transfer Switch MIB for monitoring and controlling ATS device status, measurements, and configuration.

Start monitoring Eaton automatic transfer switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download EATON-ATS2-MIB