CDMIPController

All MIBs › CDMIPController

Organization: Comtech EF Data

Last Updated: 2004-07-12

Category: Satellite, Vendor: Comtech EF Data

Description: Manages Comtech EF Data IP controller module for satellite modem IP networking configuration and routing.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CDMIPController?

CDMIPController is a vendor-specific MIB from Comtech EF Data covering the IP Controller module used in satellite modems for IP networking and routing configuration. As no module description or sample objects were provided, its precise object tree is unconfirmed, but based on its short description it would expose configuration data for IP routing/interface settings on the satellite modem's IP controller subsystem, along with likely status data on link/interface state. Its monitoring value would primarily be software/configuration status of the modem's networking function, such as confirming routing configuration is applied correctly and that the IP controller interface is operational, relevant in satellite communication links where connectivity issues are costly to diagnose remotely. It plausibly depends on standard IF-MIB/IP-MIB conventions for interface and routing objects, though this cannot be confirmed without further detail. It would be deployed in satellite ground station or VSAT terminal environments using Comtech EF Data modems. Engineers can download the CDMIPController file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CDMIPController. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Comtech EF Data satellite modem (IP Controller module)

Monitoring Examples

No sample_objects were supplied for this MIB, so specific object or table names cannot be cited with confidence; a plausible use would be checking IP interface/routing configuration and operational status on the satellite modem's IP controller, but this cannot be detailed further without concrete object names.

What Can Be Monitored

IP interface configuration
routing configuration status
IP controller operational state

Imported Objects

From ComtechEFData

comtechEFData

MODULE-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
cdmip3xDesConfig	1.3.6.1.4.1.6247.4.2.7
IP cdmipAccessIpAddress1	1.3.6.1.4.1.6247.4.2.4.1	IpAddress	read-write	Access IP Address #1: Used to restrict modem management through Web, Telnet, or SNMP to specific IP Addresses.
IP cdmipAccessIpAddress2	1.3.6.1.4.1.6247.4.2.4.3	IpAddress	read-write	Access IP Address #2 Used to restrict modem management through Web, Telnet, or SNMP to specific IP Addresses.
IP cdmipAccessIpAddress3	1.3.6.1.4.1.6247.4.2.4.5	IpAddress	read-write	Access IP Address #3: Used to restrict modem management through Web, Telnet, or SNMP to specific IP Addresses.
IP cdmipAccessIpAddress4	1.3.6.1.4.1.6247.4.2.4.7	IpAddress	read-write	Access IP Address #4: Used to restrict modem management through Web, Telnet, or SNMP to specific IP Addresses.
INT cdmipAccessListEnforcement	1.3.6.1.4.1.6247.4.2.4.9	INTEGER	read-write	Access List Enforcement Note: Be sure that you have added the SNMP browser's/manager's IP Address to the access list before enabling access list filtering. Otherwise, the SNMP browser/manager will no longer be able to gain access to the SNMP agent.
cdmipAccessLists	1.3.6.1.4.1.6247.4.2.4
INT cdmipAccessSubnetMaskLen1	1.3.6.1.4.1.6247.4.2.4.2	INTEGER	read-write	Subnet Mask Length for Access IP Address #1.
INT cdmipAccessSubnetMaskLen2	1.3.6.1.4.1.6247.4.2.4.4	INTEGER	read-write	Subnet Mask Length for Access IP Address #2.
INT cdmipAccessSubnetMaskLen3	1.3.6.1.4.1.6247.4.2.4.6	INTEGER	read-write	Subnet Mask Length for Access IP Addres #3.
INT cdmipAccessSubnetMaskLen4	1.3.6.1.4.1.6247.4.2.4.8	INTEGER	read-write	Subnet Mask Length for Access IP Address #4.
cdmipAdministration	1.3.6.1.4.1.6247.4.2
cdmipAdministrationGroup	1.3.6.1.4.1.6247.4.10.1.1			CDM-IP Controller Administration Group.
STR cdmipAppImage1Info	1.3.6.1.4.1.6247.4.7.10.2	DisplayString	read-only	Displays version information for application image in slot #1.
STR cdmipAppImage2Info	1.3.6.1.4.1.6247.4.7.10.3	DisplayString	read-only	Displays version information for application image in slot #2.
STR cdmipAppVersion	1.3.6.1.4.1.6247.4.7.1	DisplayString	read-only	Displays the version information for the application image and FPGA images.
INT cdmipBaseModemBootFrom	1.3.6.1.4.1.6247.4.7.11	INTEGER	read-write	Setting this parameter lets the Base Modem boot from a specified image. 0. Latest - boots with the Base Modem image that has the latest timestamp (date and time). 1. Image 1 - boots with the Base Modem image stored in Image 1. 2. Image 2 - boots with the Base Modem image stored in Image 2.
STR cdmipBootImageInfo	1.3.6.1.4.1.6247.4.7.10.1	DisplayString	read-only	Displays version information for bootrom image.
cdmipCompressionStatistics	1.3.6.1.4.1.6247.4.8.6
cdmipCompressionStatisticsEntry	1.3.6.1.4.1.6247.4.8.6.1.1		not-accessible	Description.
cdmipCompressionStatisticsTable	1.3.6.1.4.1.6247.4.8.6.1		not-accessible	Description.
INT cdmipCompStatsResetCounters	1.3.6.1.4.1.6247.4.8.6.1.1.8	INTEGER	read-write	Setting this to '1' will reset all IP header compression and payload compression stats counters.
cdmipController	1.3.6.1.4.1.6247.4			CDMIP IP Controller
cdmipControllerCompliance	1.3.6.1.4.1.6247.4.10.2.1			CDM-IP Controller Compliance.
cdmipControllerCompliances	1.3.6.1.4.1.6247.4.10.2
cdmipControllerConformance	1.3.6.1.4.1.6247.4.10
cdmipControllerGroups	1.3.6.1.4.1.6247.4.10.1
INT cdmipCurrentRedundantState	1.3.6.1.4.1.6247.4.6.1	INTEGER	read-only	The redundancy state of the modem. 1. OnLine - actively passing IP traffic. 0. OffLine - in standby mode; no IP traffic.
cdmipDhcpRelayConfig	1.3.6.1.4.1.6247.4.5.2
IP cdmipDhcpServerIpAddress	1.3.6.1.4.1.6247.4.5.2.1	IpAddress	read-write	The IP address of the DHCP Server.
OCT cdmipDiffServRulesClass	1.3.6.1.4.1.6247.4.9.3.1.2	OCTET STRING	read-only	The DiffServ class name for the DiffServ rule. There are three types of DiffServ rules: 1. Expedite Forwarding 2. Class-1 to Class-8 3. Assured Forwarding-1 to Assured Forwarding-4 * NOTE: This is NOT a user configurable parameter. *
I32 cdmipDiffServRulesDscp	1.3.6.1.4.1.6247.4.9.3.1.3	Integer32	read-only	The DiffServ code point (DSCP) for the DiffServ rule. * NOTE: This is NOT a user configurable parameter. *
cdmipDiffServRulesEntry	1.3.6.1.4.1.6247.4.9.3.1		not-accessible	Description.
INT cdmipDiffServRulesIndex	1.3.6.1.4.1.6247.4.9.3.1.1	INTEGER	read-write	The index for the DiffServ rule.
INT cdmipDiffServRulesMaxBw	1.3.6.1.4.1.6247.4.9.3.1.5	INTEGER	read-write	The maximum bandwidth (Kbps) for the DiffServ rule. * NOTE: This value can only be set for DiffServ rules of 'Assured Forwarding Class'. *
INT cdmipDiffServRulesMinBw	1.3.6.1.4.1.6247.4.9.3.1.4	INTEGER	read-write	The minimum bandwidth (Kbps) for the DiffServ rule. * NOTE: This value can only be set for DiffServ rules of 'Assured Forwarding Class'. NOTE: The total minimum bandwidth of all rules should NOT exceed the Tx data rate of the modem. *
INT cdmipDiffServRulesPriority	1.3.6.1.4.1.6247.4.9.3.1.6	INTEGER	read-only	The priority of the DiffServ rule. * NOTE: This is NOT a user configurable parameter. *
INT cdmipDiffServRulesRowStatus	1.3.6.1.4.1.6247.4.9.3.1.9	INTEGER	read-write	In SMIv2 tables, the RowStatus textual convention is used to manage the creation and deletion of conceptual rows. This column has six defined values. active(1) - which indicates that the conceptual row with all column is available for use by the managed device notInService(2) - this row state is not yet supported notReady(3) - this row state is not yet supported createAndGo(4) - which is supplied by a manager wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. createAndWait(5) - this row create is not yet supported destroy(6) - which is supplied by a manager wishing to delete all of the instances associated with an existing conceptual row. Right now, the diffserv initialisation process creates all necessary Diffserv rules. User is allowed to modify minBw & maxBw for ASF (Assured Forwarding) class rules only. User is not allowed to create new rules.
cdmipDiffServRulesTable	1.3.6.1.4.1.6247.4.9.3		not-accessible	Differential Services (DiffServ) Rules Table.
ENA cdmipDownlinkRouteMulticastFeature	1.3.6.1.4.1.6247.4.2.6.4	EnableDisable	read-write	Enable or disable 'downlink multicast routing' option (Satellite to Ethernet).
C32 cdmipDroppedPacketsBadBufferLength	1.3.6.1.4.1.6247.4.8.3.20	Counter32	read-only	The number of packets dropped because of a bad buffer length.
C32 cdmipDroppedPacketsBadIpHeader	1.3.6.1.4.1.6247.4.8.3.14	Counter32	read-only	The total number of packets dropped because of a bad IP header checksum.
C32 cdmipDroppedPacketsBadIpVersion	1.3.6.1.4.1.6247.4.8.3.21	Counter32	read-only	The number of packets dropped because of an unsupported IP version (i.e. V6).
C32 cdmipDroppedPacketsEasyConnectMulticastOption	1.3.6.1.4.1.6247.4.8.3.23	Counter32	read-only	The number of multicast packets dropped in EasyConnect mode because the Multicast Option is disabled.
C32 cdmipDroppedPacketsFiltered	1.3.6.1.4.1.6247.4.8.3.17	Counter32	read-only	The number of packets dropped because of a software decision.
C32 cdmipDroppedPacketsMulticast	1.3.6.1.4.1.6247.4.8.3.16	Counter32	read-only	The number of multicast packets dropped because of 'Satellite to Ethernet Option' is disabled.
C32 cdmipDroppedPacketsMulticastDisableGroup	1.3.6.1.4.1.6247.4.8.3.18	Counter32	read-only	The number of multicast packets dropped because the IGMP multicast group is disabled.
C32 cdmipDroppedPacketsNoArpEntry	1.3.6.1.4.1.6247.4.8.3.19	Counter32	read-only	The number of packets dropped because there is no ARP entry in the ARP table.
C32 cdmipDroppedPacketsNoRoute	1.3.6.1.4.1.6247.4.8.3.15	Counter32	read-only	The total number of packets dropped because of no route.
C32 cdmipDroppedPacketsQosFilterRule	1.3.6.1.4.1.6247.4.8.3.22	Counter32	read-only	The number of packets filtered because of the 'Filter' flag on a QoS rule.
C32 cdmipDroppedPacketsRouterQueueFull	1.3.6.1.4.1.6247.4.8.3.24	Counter32	read-only	The total number of packets dropped because router queue is full.
C32 cdmipDroppedPacketsTotal	1.3.6.1.4.1.6247.4.8.3.12	Counter32	read-only	The total number of packets dropped for any reason.
C32 cdmipDroppedPacketsTTLExpired	1.3.6.1.4.1.6247.4.8.3.13	Counter32	read-only	The total number of packets dropped because TTL (time to live) expired.
ENA cdmipEasyconnectMulticastOption	1.3.6.1.4.1.6247.4.2.11	EnableDisable	read-write	Enable/Disable the Easyconnect multicast option. Enabling this option allows the modem working in EasyConnect operation to pass multicast traffic.
AVA cdmipEncryptionOption	1.3.6.1.4.1.6247.4.2.5.6	Availability	read-only	Triple DES Encryption FAST Option.
cdmipEthernetInterface	1.3.6.1.4.1.6247.4.3.1
IP cdmipEthernetIpAddress	1.3.6.1.4.1.6247.4.3.1.3	IpAddress	read-write	The IP address for the Ethernet interface.
STR cdmipEthernetMacAddress	1.3.6.1.4.1.6247.4.3.1.1	DisplayString	read-only	The MAC address for the Ethernet interface.
INT cdmipEthernetSpeed	1.3.6.1.4.1.6247.4.3.1.2	INTEGER	read-write	The speed and mode of the Ehternet interface: The valid settings are: 1. Automatic. 2. 10 Mbps - Half Duplex. 3. 100 Mpbs - Half Duplex. 4. 10 Mbps - Full Duplex. 5. 100 Mbps - Full Duplex.
cdmipEthernetStatistics	1.3.6.1.4.1.6247.4.8.1
INT cdmipEthernetSubnetPrefixLen	1.3.6.1.4.1.6247.4.3.1.4	INTEGER	read-write	The subnet mask prefix length for the Ethernet interface.
C32 cdmipEtherReceiveAllignErrorCount	1.3.6.1.4.1.6247.4.8.1.12	Counter32	read-only	The number of frames that are both misaligned [in other words, CRS de-asserts on a non-octet boundary] and contain a CRC error.
C32 cdmipEtherReceiveCollisionDetectErrorCount	1.3.6.1.4.1.6247.4.8.1.15	Counter32	read-only	The number of frames that encountered a collision during reception. This counter is always zero on the 82559 Ethernet chip.
C32 cdmipEtherReceiveCRCErrorFrameCount	1.3.6.1.4.1.6247.4.8.1.11	Counter32	read-only	The number of aligned frames discarded due to a CRC error.
C32 cdmipEtherReceiveFifoOverrunErrorCount	1.3.6.1.4.1.6247.4.8.1.14	Counter32	read-only	The number of frames known to be lost because the internal receive FIFO overflowed [also known as receive overrun]. This can occur if the device is unable to get necessary PCI bandwidth. If the overflow condition persists for more than one frame, the frames that follow the first can also be lost. A frame that was counted as an overrun will not be counted in other error counters, like short frames, misaligned, or CRC error.
C32 cdmipEtherReceiveFlowControlPauseFrames	1.3.6.1.4.1.6247.4.8.1.18	Counter32	read-only	The number of flow control frames received by the device. This count includes both XOFF and XON frames received.
C32 cdmipEtherReceiveGoodFrames	1.3.6.1.4.1.6247.4.8.1.10	Counter32	read-only	The number of frames properly received from the link. It is updated only after actual reception from the link is completed and all data bytes are stored in memory.
C32 cdmipEtherReceiveResourceErrorCount	1.3.6.1.4.1.6247.4.8.1.13	Counter32	read-only	The number of good frames discarded to unavailable resources.
C32 cdmipEtherReceiveShortFrameCount	1.3.6.1.4.1.6247.4.8.1.16	Counter32	read-only	The number of received frames that are shorter than the minimum frame length.
INT cdmipEtherResetCounters	1.3.6.1.4.1.6247.4.8.1.19	INTEGER	read-write	Setting this parameter to '1' will reset all Ethernet transmit and receive counters.
C32 cdmipEtherTransmitDeferredCount	1.3.6.1.4.1.6247.4.8.1.6	Counter32	read-only	The number of frames deferred before transmission due to activity on the link.
C32 cdmipEtherTransmitDMAUnderrunCount	1.3.6.1.4.1.6247.4.8.1.4	Counter32	read-only	The number of frames that were either NOT transmitted OR retransmitted due to transmit DMA underrun. Underruns occur due to lack of PCI bandwidth resulting in the internal transmit FIFO running dry during the transmission of a frame.
C32 cdmipEtherTransmitFlowControlPauseFrames	1.3.6.1.4.1.6247.4.8.1.17	Counter32	read-only	The number of flow control frames transmitted by the device. This count includes both the XOFF and XON frames transmitted by the device.
C32 cdmipEtherTransmitGoodFrames	1.3.6.1.4.1.6247.4.8.1.1	Counter32	read-only	The number of transmitted good frames from the Ethernet interface.
C32 cdmipEtherTransmitLateCollisionCount	1.3.6.1.4.1.6247.4.8.1.3	Counter32	read-only	The number of frames that were NOT transmitted because they encountered a collision outside the normal collision window.
C32 cdmipEtherTransmitLostCarrierSenseCount	1.3.6.1.4.1.6247.4.8.1.5	Counter32	read-only	The number of frames transmitted by the device despite the fact that it detected the de-assertion of Transmit Lost Carrier Sense (CRS) during the transmission.
C32 cdmipEtherTransmitMaxCollisionCount	1.3.6.1.4.1.6247.4.8.1.2	Counter32	read-only	The number of frames that were NOT transmitted because they encountered maximum configured collisions. This counter should only increment when network is heavily saturated with traffic.
C32 cdmipEtherTransmitMultipleCollisionCount	1.3.6.1.4.1.6247.4.8.1.8	Counter32	read-only	The number of transmitted frames that encountered more than one collision.
C32 cdmipEtherTransmitSingleCollisionCount	1.3.6.1.4.1.6247.4.8.1.7	Counter32	read-only	The number of transmitted frames that encountered only one collision.
C32 cdmipEtherTransmitTotalCollisionCount	1.3.6.1.4.1.6247.4.8.1.9	Counter32	read-only	This counter contains the total number of collisions that were encountered while attempting to transmit. This count includes late collisions and collisions from frames that encountered maximum collisions.
cdmipFeaturesAvailability	1.3.6.1.4.1.6247.4.2.5
cdmipFeaturesConfig	1.3.6.1.4.1.6247.4.2.6
INT cdmipForceUnitOffline	1.3.6.1.4.1.6247.4.6.6	INTEGER	read-write	The allows the user to force a modem into standby mode. When a 'force' is executed the ONLINE unit goes to standby mode. Also, the OFFLINE unit now becomes active. * NOTE: A 'force' can only be executed on the ONLINE unit. *
INT cdmipFramerVersion	1.3.6.1.4.1.6247.4.7.10.4	INTEGER	read-only	Displays version information for framer installed in the IP card.
INT cdmipHdrcompRatio	1.3.6.1.4.1.6247.4.8.6.1.1.4	INTEGER	read-only	The percentage (%) of saving gained by performing IP header compression on all packets destined for the Satellite interface. The percentage is then multiplied by 100 to make it an integer.
INT cdmipHdrcompRefreshRateAllOther	1.3.6.1.4.1.6247.4.2.14	INTEGER	read-write	Header Compression Refresh Rate for all other protocols. Valid range is 1 - 600 packet per full IP Header.
INT cdmipHdrcompRefreshRateUdp	1.3.6.1.4.1.6247.4.2.13	INTEGER	read-write	Header Compression Refresh Rate for UDP. Valid range is 1 - 600 packets per full IP/UDP Header.
INT cdmipHdrcompRefreshRateUdpRtp1	1.3.6.1.4.1.6247.4.2.12	INTEGER	read-write	Header compression Refresh Rate for UDP/RTP1. Valid range is 1 - 600 packets per full IP/UDP/RTP Header.
C32 cdmipHdrcompStatsPostHdrcompBytes	1.3.6.1.4.1.6247.4.8.6.1.1.3	Counter32	read-only	The total number of bytes in all 'compressed' packets after IP header compression has been performed.
C32 cdmipHdrcompStatsPreHdrcompBytes	1.3.6.1.4.1.6247.4.8.6.1.1.2	Counter32	read-only	The total number of bytes in all packets before IP header compression has been performed.
INT cdmipHdrcompStatsQueueIndex	1.3.6.1.4.1.6247.4.8.6.1.1.1	INTEGER	read-only	The index of the QoS queue for which the IP header compression stats are being displayed.
AVA cdmipHeaderCompressionOption	1.3.6.1.4.1.6247.4.2.5.8	Availability	read-only	IP Header Compression FAST Option.
INT cdmipIgmpClientState	1.3.6.1.4.1.6247.4.5.1.1.1.3	INTEGER	read-only	The current state of the multicast group. Possible states are: 1. Idle. 2. Active. 3. Closing.
cdmipIgmpConfig	1.3.6.1.4.1.6247.4.5.1
ENA cdmipIgmpEnable	1.3.6.1.4.1.6247.4.5.1.2.1	EnableDisable	read-only	Enable or disable IGMP. 1. IGMP is enabled. 2. IGMP is disabled.
cdmipIgmpEntry	1.3.6.1.4.1.6247.4.5.1.1.1		not-accessible	IGMP Entry
ENA cdmipIgmpForceAlertOption	1.3.6.1.4.1.6247.4.5.1.3.3	EnableDisable	read-write	Modem as Client: Router Alert Option for V1 report.
IP cdmipIgmpGroupIpAddress	1.3.6.1.4.1.6247.4.5.1.1.1.5	IpAddress	read-only	The multicast address for the IGMP group.
INT cdmipIgmpIndex	1.3.6.1.4.1.6247.4.5.1.1.1.1	INTEGER	read-only	The index for the IGMP table.
INT cdmipIgmpMaxMissBeforeDrop	1.3.6.1.4.1.6247.4.5.1.2.4	INTEGER	read-write	Modem as Server: Number of missed responses before leaving an IGMP group.
INT cdmipIgmpMaxRespTime	1.3.6.1.4.1.6247.4.5.1.2.3	INTEGER	read-write	Modem as Sever: IGMP max. response time in seconds.
ENA cdmipIgmpOpt	1.3.6.1.4.1.6247.4.2.6.12	EnableDisable	read-write	Enable or disable IGMP option.
AVA cdmipIgmpOption	1.3.6.1.4.1.6247.4.2.5.7	Availability	read-only	IGMP FAST Option.
C32 cdmipIgmpPacketsReceived	1.3.6.1.4.1.6247.4.8.3.10	Counter32	read-only	The total number of multicast IGMP packets received from any interface.
INT cdmipIgmpQueryPeriod	1.3.6.1.4.1.6247.4.5.1.2.2	INTEGER	read-write	Modem as IGMP Server: IGMP query period in seconds.
cdmipIgmpReceiver	1.3.6.1.4.1.6247.4.5.1.2
ENA cdmipIgmpRecognizeQueries	1.3.6.1.4.1.6247.4.5.1.3.1	EnableDisable	read-write	Modem as Client: Recognize IGMP Queries
INT cdmipIgmpSrc	1.3.6.1.4.1.6247.4.5.1.1.1.4	INTEGER	read-only	Show which interface the multicast group is coming from. Possible values are: 1. Other - from the Ethernet interface. 2. Sat - from the Satellite interface.
cdmipIgmpTable	1.3.6.1.4.1.6247.4.5.1.1		not-accessible	IGMP Table
cdmipIgmpTransmiter	1.3.6.1.4.1.6247.4.5.1.3
INT cdmipIgmpTTL	1.3.6.1.4.1.6247.4.5.1.1.1.2	INTEGER	read-only	The IGMP Time to live (TTL) for the multicast group.
INT cdmipIgmpUnsolicitedReportInterval	1.3.6.1.4.1.6247.4.5.1.3.4	INTEGER	read-write	Modem as Client: Unsolicited Report Interval in seconds.
INT cdmipIgmpVersionUnsolicitedReports	1.3.6.1.4.1.6247.4.5.1.3.2	INTEGER	read-write	Modem as Client: IGMP Version used for Unsolicited Reports. Possible values are: 1. Version 1. 2. Version 2.
cdmipInterfaces	1.3.6.1.4.1.6247.4.3
cdmipInterfacesGroup	1.3.6.1.4.1.6247.4.10.1.2			CDM-IP Controller Interface Group.
INT cdmipIPModuleBootFrom	1.3.6.1.4.1.6247.4.7.7	INTEGER	read-write	Setting this parameter lets the IP Module to boot from a specified image. 0. Latest - boots with the image that has the latest timestamp (date and time). 1. Image 1 - boots with the image stored in Image 1. 2. Image 2 - boots with the image stored in Image 2.
C32 cdmipIpOptionPacketsReceived	1.3.6.1.4.1.6247.4.8.3.11	Counter32	read-only	The total number of packets received with IP options in the header.
ENA cdmipIpRoute3xDes	1.3.6.1.4.1.6247.4.4.3.1.11	EnableDisable	read-write	Enable or disable 3xDES [Triple DES Encryption] on this route. It may return 'commit_failed' if 3xDES feature is not available on modem.
INT cdmipIpRouteDesKey	1.3.6.1.4.1.6247.4.4.3.1.12	INTEGER	read-write	Pick which DES key to use for this route. The system supports 8 3xDES (Triple DES - 24 Byte Length) keys. This specifies the 3xDES key to be used for this flow. 1 - 8 for Key1 to Key8 9 - Randomly pick one of the 8 keys. 10 - Clear
IP cdmipIpRouteDestAddress	1.3.6.1.4.1.6247.4.4.3.1.3	IpAddress	read-write	The destination IP address for the route. *Note*: Do not add multicast routes for Vipersat Multicast addresses.
INT cdmipIpRouteDestMaskLen	1.3.6.1.4.1.6247.4.4.3.1.4	INTEGER	read-write	The number of bits in the subnet mask for the destination IP address for the route.
cdmipIpRouteEntry	1.3.6.1.4.1.6247.4.4.3.1		not-accessible	CDMIP IP Route Entry
INT cdmipIpRouteHdlcAddress	1.3.6.1.4.1.6247.4.4.3.1.8	INTEGER	read-write	The HDLC Address is valid only for routes destined to the Satellite interface. This can also be viewed as the 'next-hop' identifier for the route destined to satellite. The valid range of HDLC Address depends on Network mode. 1. Small Network mode - 1 - 254 (0x01 - 0xFE) 2. Large Network Mode - 1 - 32766 (0x01 - 0x7FFE) An HDLC Address cannot have 0x00 or 0xFF in Least Significant Byte (LSB). Set 'cdmipIpRouteState' to 'toSatellite' state before setting 'cdmipIpRouteHdlcAddress'.
ENA cdmipIpRouteHdrComp	1.3.6.1.4.1.6247.4.4.3.1.9	EnableDisable	read-write	Enable or disable IP header compression on this route. To Set this parameter, you need to have Header Compression Feature available on your modem. It may return 'commit_failed' if feature is not available on modem.
INT cdmipIpRouteIndex	1.3.6.1.4.1.6247.4.4.3.1.1	INTEGER	read-write	The index for the route table.
INT cdmipIpRouteMulticastOptions	1.3.6.1.4.1.6247.4.4.3.1.6	INTEGER	read-write	Configures how router should handle multicast traffic. Valid options are: 1. Do not forward any multicast traffic (drop all). 2. Forward multicast traffic from Ethernet to Satellite only. 3. Forward multicast traffic from Satellite to Ethernet only. 4. Forward multicast traffic in both directions.
STR cdmipIpRouteName	1.3.6.1.4.1.6247.4.4.3.1.2	DisplayString	read-write	The name for the route. The route name must be unique.
IP cdmipIpRouteNextHopAddress	1.3.6.1.4.1.6247.4.4.3.1.5	IpAddress	read-write	The Next Hop IP Address is valid only for routes destined to the Ethernet interface. This IP address must be a locally attached router. Set 'cdmipIpRouteState' to 'toEthernet' state before setting 'cdmipIpRouteNextHopAddress'.
ENA cdmipIpRoutePayloadComp	1.3.6.1.4.1.6247.4.4.3.1.10	EnableDisable	read-write	Enable or disable payload compression on this route. To set this parameter, you need to have Datagram/Payload Compression feature available on your modem. It may return 'commit_failed' if feature is not available on modem.
INT cdmipIpRouteRowStatus	1.3.6.1.4.1.6247.4.4.3.1.13	INTEGER	read-write	In SMIv2 tables, the RowStatus textual convention is used to manage the creation and deletion of conceptual rows. This column has six defined values. active(1) - which indicates that the conceptual row with all column is available for use by the managed device notInService(2) - this row state is not yet supported notReady(3) - this row state is not yet supported createAndGo(4) - which is supplied by a manager wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. createAndWait(5) - this row create is not yet supported destroy(6) - which is supplied by a manager wishing to delete all of the instances associated with an existing conceptual row.
INT cdmipIpRouteState	1.3.6.1.4.1.6247.4.4.3.1.7	INTEGER	read-write	The route state specifies the route's destination. The valid values are: 1. To Ethernet (route goes to Ethernet interface). 2. To Satellite (route goes to Satellite interface).
cdmipIpRouteTable	1.3.6.1.4.1.6247.4.4.3		not-accessible	CDMIP IP Route Table
cdmipIpRoutingStatistics	1.3.6.1.4.1.6247.4.8.3
INT cdmipLoadParamsFromStorage	1.3.6.1.4.1.6247.4.7.6	INTEGER	read-write	Setting the value to '1' will load the PARAM from the permanent storage. Only value: 1. Load - load PARAM from permanent storage.
IP cdmipLocalUnitManagementIpAddress	1.3.6.1.4.1.6247.4.6.2	IpAddress	read-only	The IP Address for management of the IP parameters (READ ONLY). * NOTE: This address is the same as the Ethernet IP address. *
INT cdmipMibVersion	1.3.6.1.4.1.6247.4.2.1	INTEGER	read-only	/****************************************************************************/ / * CDM-IP MIB Version Information * * Date App Release MIB Version * ======== =========== =========== * 03/14/02 1.0 1 * * 04/23/02 internal 2 * * 07/31/02 1.1 3 * * 10/15/02 1.2 4 * * 11/25/02 2.1 5 * * 02/19/04 4.0 6 * * 07/12/04 4.2 7 * * 12/31/05 5.3 8 / /****************************************************************************/
cdmipOperMaint	1.3.6.1.4.1.6247.4.7
cdmipOperMaintGroup	1.3.6.1.4.1.6247.4.10.1.6			CDM-IP Controller Oper. Maint. Group.
INT cdmipParamConfig	1.3.6.1.4.1.6247.4.7.9	INTEGER	read-write	Setting this parameter tells how the IP card will get its configuration data when booting up: Configuration data can be loaded from the following locations: 1. Factory Defaultls - load data from factory defaults. 2. PARAM File - load data from PARAM in permanent storage.
C32 cdmipPayloadCompPostPayloadCompBytes	1.3.6.1.4.1.6247.4.8.6.1.1.6	Counter32	read-only	The total number of bytes in all packets after payload compression has been performed. To get the standard payload compression ratio in the form 1:x.xx (Pre Payload Compression Bytes) x.xx = ------------------------------- (Post Payload Compression Bytes)
C32 cdmipPayloadCompPrePayloadCompBytes	1.3.6.1.4.1.6247.4.8.6.1.1.5	Counter32	read-only	The total number of bytes in all packets before payload compression has been performed. To get the standard payload compression ratio in the form 1:x.xx (Pre Payload Compression Bytes) x.xx = ------------------------------- (Post Payload Compression Bytes)
INT cdmipPayloadCompRatio	1.3.6.1.4.1.6247.4.8.6.1.1.7	INTEGER	read-only	This parameter is the standard payload compression ratio. To get the standard payload compression ratio in the form 1:x.xx (Pre Payload Compression Bytes) x.xx = ------------------------------- (Post Payload Compression Bytes) The ratio is then converted into an integer by multiplying by 100.
INT cdmipPayloadCompRefreshRate	1.3.6.1.4.1.6247.4.2.15	INTEGER	read-write	Refresh rate for Payload Compression in packets. Valid range is 1 = 600 packets before a refresh ofthe payload compression algorithm is done.
AVA cdmipPayloadCompressionOption	1.3.6.1.4.1.6247.4.2.5.9	Availability	read-only	IP Payload Compression FAST Option.
ENA cdmipPingReplyFeature	1.3.6.1.4.1.6247.4.2.6.3	EnableDisable	read-write	Enable or disable ICMP Ping Reply from the modem.
cdmipProtocols	1.3.6.1.4.1.6247.4.5
cdmipProtocolsGroup	1.3.6.1.4.1.6247.4.10.1.4			CDM-IP Controller Protocols Group.
INT cdmipQosMode	1.3.6.1.4.1.6247.4.9.4	INTEGER	read-write	The QoS configuration modes for the QoS subsystem. The valid values are: 1. Maximum Bandwidth & Priority. 2. Minimum Bandwidth & Maximum Bandwidth. 3. Differential Services Mode.
ENA cdmipQosOpt	1.3.6.1.4.1.6247.4.2.6.7	EnableDisable	read-write	Enable or disable 'Quality of Service' (QoS) in the modem's router.
AVA cdmipQosOption	1.3.6.1.4.1.6247.4.2.5.3	Availability	read-only	Quality of Server (QoS) FAST Option.
cdmipQosRules	1.3.6.1.4.1.6247.4.9
IP cdmipQosRulesDstIpAddr	1.3.6.1.4.1.6247.4.9.2.1.4	IpAddress	read-write	The destination IP address for the QoS rule.
INT cdmipQosRulesDstIpMaskLen	1.3.6.1.4.1.6247.4.9.2.1.5	INTEGER	read-write	The destination IP subnet mask length for the QoS rule.
INT cdmipQosRulesDstPortMax	1.3.6.1.4.1.6247.4.9.2.1.10	INTEGER	read-write	The ending destination port number (maximum) for the QoS rule. A QoS rule can be configured with a port range of xxxx - yyyy by setting 'cdmipQosRulesDstPortMin' to xxxx and 'cdmipQosRulesDstPortMax' to yyyy. * NOTE: Enter 65536 for match all ports. *
INT cdmipQosRulesDstPortMin	1.3.6.1.4.1.6247.4.9.2.1.9	INTEGER	read-write	The starting destination port number (minimum) for the QoS rule. A QoS rule can be configured with a port range of xxxx - yyyy by setting 'cdmipQosRulesDstPortMin' to xxxx and 'cdmipQosRulesDstPortMax' to yyyy. * NOTE: Enter 65536 for match all ports. *
cdmipQosRulesEntry	1.3.6.1.4.1.6247.4.9.2.1		not-accessible	Description.
ENA cdmipQosRulesFilter	1.3.6.1.4.1.6247.4.9.2.1.15	EnableDisable	read-write	The filter option for the QoS rule. * NOTE: This option will filter ALL packets associated with this QoS rule. *
cdmipQosRulesGroup	1.3.6.1.4.1.6247.4.10.1.8			CDM-IP Controller Qos Rules Group.
INT cdmipQosRulesIndex	1.3.6.1.4.1.6247.4.9.2.1.1	INTEGER	read-write	The index for the QoS rule. The valid values are 1 - 32.
INT cdmipQosRulesMaxBw	1.3.6.1.4.1.6247.4.9.2.1.12	INTEGER	read-write	The maximum bandwidth (Kbps) for the QoS rule. * NOTE: Valid for both 'Maximum Bandwidth & Priority' and 'Minimum Bandwidth & Maximum Bandwidth' modes. *
INT cdmipQosRulesMinBw	1.3.6.1.4.1.6247.4.9.2.1.11	INTEGER	read-write	The minimum bandwidth (Kbps) for the QoS rule. * NOTE: Only valid for 'Minimum Bandwidth & Maximum Bandwidth' mode. *
INT cdmipQosRulesPriority	1.3.6.1.4.1.6247.4.9.2.1.13	INTEGER	read-write	The priority for the QoS rule. The valid values are: Priority 1 - Highest Priority 2, 3, 4, 5, 6, 7 - Middle Priority 8 - Lowest * NOTE: Only valid for 'Maximum Bandwidth & Priority' mode. *
INT cdmipQosRulesProtocol	1.3.6.1.4.1.6247.4.9.2.1.6	INTEGER	read-write	The protocol type for the QoS rule. Only the default rule is configured with 'All'. Setting protocol field to 'All' for other rules is not permitted, may result in 'wrong value' Setting the protocol to Non-IP would configure the QoS rule parameters to pre-set default values. User is only allowed to set max bandwidth, priority & filter flag for a Non-IP qos rule. User is not allowed to create/modify a rule with RTP Signaling protocol. The software does this. IMPORTANT: Configure rtpSignal rule for rtpVoice/rtpVideo rules.
INT cdmipQosRulesRowStatus	1.3.6.1.4.1.6247.4.9.2.1.16	INTEGER	read-write	In SMIv2 tables, the RowStatus textual convention is used to manage the creation and deletion of conceptual rows. This column has six defined values. active(1) - which indicates that the conceptual row with all column is available for use by the managed device. notInService(2) - this row state is not yet supported. notReady(3) - this row state is not yet supported. createAndGo(4) - which is supplied by a manager wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. createAndWait(5) - this row create is not yet supported destroy(6) - which is supplied by a manager wishing to delete all of the instances associated with an existing conceptual row.
IP cdmipQosRulesSrcIpAddr	1.3.6.1.4.1.6247.4.9.2.1.2	IpAddress	read-write	The source IP address for the QoS rule.
INT cdmipQosRulesSrcIpMaskLen	1.3.6.1.4.1.6247.4.9.2.1.3	INTEGER	read-write	The source IP subnet mask length for the QoS rule.
INT cdmipQosRulesSrcPortMax	1.3.6.1.4.1.6247.4.9.2.1.8	INTEGER	read-write	The ending UDP/TCP source port (maximum) for the QoS rule. A QoS rule can be configured with a port range of aaaa - bbbb by setting 'cdmipQosRulesSrcPortMin' to aaaa and 'cdmipQosRulesSrcPortMax' to bbbb. * NOTE: Enter 65536 to match all ports. *
INT cdmipQosRulesSrcPortMin	1.3.6.1.4.1.6247.4.9.2.1.7	INTEGER	read-write	The starting UDP/TCP source port (minimum) for the QoS rule. A QoS rule can be configured with a port range of aaaa - bbbb by setting 'cdmipQosRulesSrcPortMin' to aaaa and 'cdmipQosRulesSrcPortMax' to bbbb. * NOTE: Enter 65536 to match all ports. *
cdmipQosRulesTable	1.3.6.1.4.1.6247.4.9.2		not-accessible	Description.
ENA cdmipQosRulesWred	1.3.6.1.4.1.6247.4.9.2.1.14	EnableDisable	read-write	The WRED (Weighted Random Early Drop) option for the QoS rule. This is the mechanism by which packets are treated upon queue full. If this is enabled, the packets are dropped randomly upon detection of queue full or queue getting full.
cdmipQosStatistics	1.3.6.1.4.1.6247.4.8.4
cdmipQosStatisticsEntry	1.3.6.1.4.1.6247.4.8.4.1.1		not-accessible	Description.
cdmipQosStatisticsTable	1.3.6.1.4.1.6247.4.8.4.1		not-accessible	Description.
C32 cdmipQosStatsActiveFlows	1.3.6.1.4.1.6247.4.8.4.1.1.10	Counter32	read-only	The number of active flows associated with this QoS queue.
C32 cdmipQosStatsAverageTxRate	1.3.6.1.4.1.6247.4.8.4.1.1.8	Counter32	read-only	The average Tx data rate associated with this QoS queue.
C32 cdmipQosStatsCurrentTxRate	1.3.6.1.4.1.6247.4.8.4.1.1.7	Counter32	read-only	The current Tx data rate associated with this QoS queue.
C32 cdmipQosStatsDroppedBytes	1.3.6.1.4.1.6247.4.8.4.1.1.6	Counter32	read-only	The total number of bytes dropped from this QoS queue.
C32 cdmipQosStatsDroppedPackets	1.3.6.1.4.1.6247.4.8.4.1.1.5	Counter32	read-only	The total number of packets dropped from this QoS queue.
C32 cdmipQosStatsMaxTxRate	1.3.6.1.4.1.6247.4.8.4.1.1.9	Counter32	read-only	The maximum Tx data rate associated with this QoS queue.
INT cdmipQosStatsQueueIndex	1.3.6.1.4.1.6247.4.8.4.1.1.1	INTEGER	read-only	The index of the QoS rule for which stats are being displayed.
INT cdmipQosStatsResetCounters	1.3.6.1.4.1.6247.4.8.4.1.1.11	INTEGER	read-write	Setting this to '1' will reset all the statistics counters associated with this QoS queue.
C32 cdmipQosStatsSentBytes	1.3.6.1.4.1.6247.4.8.4.1.1.4	Counter32	read-only	The total number of bytes sent through this QoS queue.
C32 cdmipQosStatsSentPackets	1.3.6.1.4.1.6247.4.8.4.1.1.2	Counter32	read-only	The total number of packets sent through this QoS queue.
C32 cdmipQosStatsSentPacketsPerSecond	1.3.6.1.4.1.6247.4.8.4.1.1.3	Counter32	read-only	The number of packets per second sent through this QoS queue.
STR cdmipReceiveKey1	1.3.6.1.4.1.6247.4.2.7.11	DisplayString	read-write	Triple DES (3xDES) Receive Decrypt Key #1. The key length is 192 bits (24 bytes or 48 HEX characters).
STR cdmipReceiveKey2	1.3.6.1.4.1.6247.4.2.7.12	DisplayString	read-write	Triple DES (3xDES) Receive Decrypt Key #2. The key length is 192 bits (24 bytes or 48 HEX characters).
STR cdmipReceiveKey3	1.3.6.1.4.1.6247.4.2.7.13	DisplayString	read-write	Triple DES (3xDES) Receive Decrypt Key #3. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipReceiveKey4	1.3.6.1.4.1.6247.4.2.7.14	DisplayString	read-write	Triple DES (3xDES) Receive Decrypt Key #4. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipReceiveKey5	1.3.6.1.4.1.6247.4.2.7.15	DisplayString	read-write	Triple DES (3xDES) Receive Decrypt Key #5. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipReceiveKey6	1.3.6.1.4.1.6247.4.2.7.16	DisplayString	read-write	Triple DES (3xDES) Receive Decrypt Key #6. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipReceiveKey7	1.3.6.1.4.1.6247.4.2.7.17	DisplayString	read-write	Triple DES (3xDES) Receive Decrypt Key #7. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipReceiveKey8	1.3.6.1.4.1.6247.4.2.7.18	DisplayString	read-write	Triple DES (3xDES) Receive Decrypt Key #8. The key length is 192 bits (24 Bytes or 48 HEX characters).
cdmipRedundancy	1.3.6.1.4.1.6247.4.6
cdmipRedundancyGroup	1.3.6.1.4.1.6247.4.10.1.5			CDM-IP Controller Redundancy Group.
IP cdmipRedundantTrafficIpAddress	1.3.6.1.4.1.6247.4.6.4	IpAddress	read-write	The IP address for traffic passing through the redundant pair of modem. This address is only active in the ONLINE modem. * NOTE: The traffic IP can only be set on the ONLINE unit. *
INT cdmipRedundantTrafficSubnetMaskLen	1.3.6.1.4.1.6247.4.6.5	INTEGER	read-write	The subnet mask prefix length for the traffic IP address. * NOTE: The traffic IP subnet mask can only be set on the ONLINE unit. *
IP cdmipRedundantUnitManagementIpAddress	1.3.6.1.4.1.6247.4.6.3	IpAddress	read-only	The IP Address of the redundant unit (READ ONLY). * NOTE: This address is the same as other unit's Ethernet IP address. *
INT cdmipReset	1.3.6.1.4.1.6247.4.7.3	INTEGER	read-write	Setting this value to '1' will reboot the IP card. Only value: 1. Rest - reboot the IP card.
INT cdmipResetCounters	1.3.6.1.4.1.6247.4.8.3.26	INTEGER	read-write	Setting this parameter to '1' will clear all IP routing, WAN, and Ethernet statistics.
INT cdmipRestoreFactoryDefaults	1.3.6.1.4.1.6247.4.7.5	INTEGER	read-write	Setting this value to '1' will restore factory defaults to the system. Only value: 1. Restore - restore factory defaults. * NOTE: Restoring factory defaults will erase PARAM in permanent storage. Make sure, before setting this to True. *
cdmipRouteTable	1.3.6.1.4.1.6247.4.4
cdmipRouteTableGroup	1.3.6.1.4.1.6247.4.10.1.3			CDM-IP Controller Route Table Group.
ENA cdmipRxHeaderCompressionOpt	1.3.6.1.4.1.6247.4.2.6.14	EnableDisable	read-write	Enable or disable Receive 'IP Header Compression' option.
INT cdmipSatelliteHdlcAddress1	1.3.6.1.4.1.6247.4.3.2.5	INTEGER	read-write	HDLC Channel Address #1 filtered by the HSR Valid values of HDLC address depends on the Network mode. In Small Network Mode - Frame will have 1 Byte of HDLC addr. valid values are 1 - 254. (0x1 - 0xFE) In Large Network Mode - Frame will have 2 Bytes of HDLC address. valid values are 1 - 32766 (0x1 - 0x7FFE) In Point-to-Point Mode - HDLC addresses are NOT-USED. An HDLC Address of '0(Zero)' is interpretted as NOT-DEFINED or NOT-USED An HDLC address cannot have 0x00 or 0xFF in least Significant Byte. i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses. User is NOT allowed to configure HDLC address while system is operating in EASY CONNECT MODE. To Invalidate/Delete HDLC Address, set the MIB member 'cdmipSatelliteHdlcAddressDelete' to the HDLC address number. HDLC Address number range from 1...4
INT cdmipSatelliteHdlcAddress2	1.3.6.1.4.1.6247.4.3.2.6	INTEGER	read-write	HDLC Channel Address #2 filtered by the HSR Valid values of HDLC address depends on the Network mode. In Small Network Mode - Frame will have 1 Byte of HDLC addr. valid values are 1 - 254. (0x1 - 0xFE) In Large Network Mode - Frame will have 2 Bytes of HDLC address. valid values are 1 - 32766 (0x1 - 0x7FFE) In Point-to-Point Mode - HDLC addresses are NOT-USED. An HDLC Address of '0(Zero)' is interpretted as NOT-DEFINED or NOT-USED An HDLC address cannot have 0x00 or 0xFF in least Significant Byte. i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses. User is NOT allowed to configure HDLC address while system is operating in EASY CONNECT MODE. To Invalidate/Delete HDLC Address, set the MIB member 'cdmipSatelliteHdlcAddressDelete' to the HDLC address number. HDLC Address number range from 1...4
INT cdmipSatelliteHdlcAddress3	1.3.6.1.4.1.6247.4.3.2.7	INTEGER	read-write	HDLC Channel Address #3 filtered by the HSR Valid values of HDLC address depends on the Network mode. In Small Network Mode - Frame will have 1 Byte of HDLC addr. valid values are 1 - 254. (0x1 - 0xFE) In Large Network Mode - Frame will have 2 Bytes of HDLC address. valid values are 1 - 32766 (0x1 - 0x7FFE) In Point-to-Point Mode - HDLC addresses are NOT-USED. An HDLC Address of '0(Zero)' is interpretted as NOT-DEFINED or NOT-USED An HDLC address cannot have 0x00 or 0xFF in least Significant Byte. i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses. User is NOT allowed to configure HDLC address while system is operating in EASY CONNECT MODE. To Invalidate/Delete HDLC Address, set the MIB member 'cdmipSatelliteHdlcAddressDelete' to the HDLC address number. HDLC Address number range from 1...4
INT cdmipSatelliteHdlcAddress4	1.3.6.1.4.1.6247.4.3.2.8	INTEGER	read-write	HDLC Channel Address #4 filtered by the HSR Valid values of HDLC address depends on the Network mode. In Small Network Mode - Frame will have 1 Byte of HDLC addr. valid values are 1 - 254. (0x1 - 0xFE) In Large Network Mode - Frame will have 2 Bytes of HDLC address. valid values are 1 - 32766 (0x1 - 0x7FFE) In Point-to-Point Mode - HDLC addresses are NOT-USED. An HDLC Address of '0(Zero)' is interpretted as NOT-DEFINED or NOT-USED An HDLC address cannot have 0x00 or 0xFF in least Significant Byte. i.e., 0x400 or 0x6ff or 0x11ff are NOT valid HDLC addresses. User is NOT allowed to configure HDLC address while system is operating in EASY CONNECT MODE. To Invalidate/Delete HDLC Address, set the MIB member 'cdmipSatelliteHdlcAddressDelete' to the HDLC address number. HDLC Address number range from 1...4
INT cdmipSatelliteHdlcAddressDelete	1.3.6.1.4.1.6247.4.3.2.9	INTEGER	read-write	Used to delete a specified HDLC Address. Setting this entry to value 1...4 deletes/invalidates the corresponding HDLC Address. 1. for HDLCAddress #1 2. for HDLCAddress #2 3. for HDLCAddress #3 4. for HDLCAddress #4 When a HDLC Address is deleted/invalidated, it is displayed as '0' (NOT-DEFINED or NOT-USED) on SNMP Gets.
INT cdmipSatelliteHdlcAddressModeConfig	1.3.6.1.4.1.6247.4.3.2.10	INTEGER	read-only	The size of HDLC address used for frames sent over the satellite interface can range from 0 - 2 bytes. This range allows the system to operate in one of these modes: 1. Small Network Mode - The frame will have 1 byte of HDLC address. Valid values are 1 - 254. (0x1 - 0xFE). 2. Large Network Mode - The frame will have 2 bytes of HDLC address. Valid values are 1 - 32767 (0x1 - 0x7FFE). 3. Point-to-Point Mode - The frame does not use any HDLC address. 4. Vipersat Mode - The frame does not use any HDLC address.
cdmipSatelliteInterface	1.3.6.1.4.1.6247.4.3.2
INT cdmipSaveConfiguration	1.3.6.1.4.1.6247.4.7.2	INTEGER	read-write	Setting this value to '1' will save the PARAM permanent storage. Only value: 1. Save - save the PARAM to permanent storage.
cdmipSmtp	1.3.6.1.4.1.6247.4.2.8
STR cdmipSmtpDestinationName	1.3.6.1.4.1.6247.4.2.8.3	DisplayString	read-write	SMTP Destination Email User Name (i.e. cdmipsupport)
STR cdmipSmtpDomain	1.3.6.1.4.1.6247.4.2.8.2	DisplayString	read-write	SMTP Domain (i.e. comtechefdata.com)
IP cdmipSmtpServerIpAddress	1.3.6.1.4.1.6247.4.2.8.1	IpAddress	read-write	IP address of the SMTP server on your local LAN.
cdmipSnmp	1.3.6.1.4.1.6247.4.2.9
IP cdmipSnmpAuthenticationFailureAddress	1.3.6.1.4.1.6247.4.2.9.5	IpAddress	accessible-for-notify	NOTE: Used ONLY in the Authentification Failure Trap (No access). IP Address which sent an SNMP message with an invalid SET or GET community string.
STR cdmipSnmpAuthenticationFailureCommunity	1.3.6.1.4.1.6247.4.2.9.4	DisplayString	accessible-for-notify	NOTE: Used ONLY in the Authentification Failure Trap (No access). The community string which was invalid for a SET or GET SNMP message.
STR cdmipSnmpTrapCommunity	1.3.6.1.4.1.6247.4.2.9.2	DisplayString	read-write	The trap community string to be used for SNMP trap messages.
IP cdmipSnmpTrapDestinationIpAddress	1.3.6.1.4.1.6247.4.2.9.1	IpAddress	read-write	SNMP Trap Destination #1: The primary IP Address to which trap will be sent.
IP cdmipSnmpTrapDestinationIpAddress2	1.3.6.1.4.1.6247.4.2.9.6	IpAddress	read-write	SNMP Trap Destination #2: The secondary IP Address to which traps will be sent.
INT cdmipSnmpTrapVersion	1.3.6.1.4.1.6247.4.2.9.3	INTEGER	read-write	The SNMP Trap Version: Use V1 for SNMP Version 1 Traps. Use V2 for SNMP Version 2 Notifications.
cdmipStatistics	1.3.6.1.4.1.6247.4.8
cdmipStatisticsGroup	1.3.6.1.4.1.6247.4.10.1.7			CDM-IP Controller Statistics Group.
ENA cdmipTelnetFeature	1.3.6.1.4.1.6247.4.2.6.2	EnableDisable	read-write	Enable or disable Telnet access for managing the modem.
C32 cdmipTotalIpPacketsFromEthernet	1.3.6.1.4.1.6247.4.8.3.3	Counter32	read-only	The total number of IP packets received from the Ethernet interface.
C32 cdmipTotalIpPacketsFromSatellite	1.3.6.1.4.1.6247.4.8.3.1	Counter32	read-only	The total number of IP packets received from the Satellite interface.
C32 cdmipTotalIpPacketsRoutedToEthernet	1.3.6.1.4.1.6247.4.8.3.4	Counter32	read-only	The total number of IP packets sent to the Ethernet interface.
C32 cdmipTotalIpPacketsRoutedToSatellite	1.3.6.1.4.1.6247.4.8.3.2	Counter32	read-only	The total number of IP packets sent to the Satellite interface.
INT cdmipTransmit3xDesEncryptionOpt	1.3.6.1.4.1.6247.4.2.6.10	INTEGER	read-write	Enable or disable 'transmit 3xDES encryption' option.
STR cdmipTransmitKey1	1.3.6.1.4.1.6247.4.2.7.3	DisplayString	read-write	Triple DES (3xDES) Transmit Encrypt Key #1. The key length is 192 bits (24 bytes or 48 HEX characters).
STR cdmipTransmitKey2	1.3.6.1.4.1.6247.4.2.7.4	DisplayString	read-write	Triple DES (3xDES) Transmit Encrypt Key #2. The key length is 192 bits (24 bytes or 48 HEX characters).
STR cdmipTransmitKey3	1.3.6.1.4.1.6247.4.2.7.5	DisplayString	read-write	Triple DES (3xDES) Transmit Encrypt Key #3. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipTransmitKey4	1.3.6.1.4.1.6247.4.2.7.6	DisplayString	read-write	Triple DES (3xDES) Transmit Encrypt Key #4. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipTransmitKey5	1.3.6.1.4.1.6247.4.2.7.7	DisplayString	read-write	Triple DES (3xDES) Transmit Encrypt Key #5. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipTransmitKey6	1.3.6.1.4.1.6247.4.2.7.8	DisplayString	read-write	Triple DES (3xDES) Transmit Encrypt Key #6. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipTransmitKey7	1.3.6.1.4.1.6247.4.2.7.9	DisplayString	read-write	Triple DES (3xDES) Transmit Encrypt Key #7. The key length is 192 bits (24 Bytes or 48 HEX characters).
STR cdmipTransmitKey8	1.3.6.1.4.1.6247.4.2.7.10	DisplayString	read-write	Triple DES (3xDES) Transmit Encrypt Key #8. The key length is 192 bits (24 Bytes or 48 HEX characters).
INT cdmipTxHeaderCompressionOpt	1.3.6.1.4.1.6247.4.2.6.13	INTEGER	read-write	Enable or disable the Transmit 'IP Header Compression' option.
INT cdmipTxPayloadCompressionOpt	1.3.6.1.4.1.6247.4.2.6.15	INTEGER	read-write	Enable or disable 'Tx Payload Compression' option.
cdmipUnitInformation	1.3.6.1.4.1.6247.4.7.10
INT cdmipUpgradeTo	1.3.6.1.4.1.6247.4.7.8	INTEGER	read-write	Setting this parameter specifies Image to overwrite with the new upgraded image. 0. Oldest - Saves the new upgrade image over the image that has the oldest timestamp (date and time). 1. Image1 - Saves the new upgrade image into Image #1. 2. Image2 - Saves the new upgrade image into Image #2. * NOTE: This parameter must be set before performing an upgrade. *
INT cdmipWanFpgaActualWanTraffic	1.3.6.1.4.1.6247.4.8.5.15	INTEGER	read-only	The 'compressed' data rate (Kbps) after IP header and payload compression of traffic transmitted on the Satellite interface.
INT cdmipWanFpgaLanToWanTraffic	1.3.6.1.4.1.6247.4.8.5.14	INTEGER	read-only	The data rate (Kbps) before IP header and payload compression of Ethernet traffic destined for the Satellite interface.
INT cdmipWanFpgaResetAllCounters	1.3.6.1.4.1.6247.4.8.5.12	INTEGER	read-write	Setting this variable to 'reset' will reset all the WAN FPGA Rx & Tx counters.
C32 cdmipWanFpgaRxAbortOctetErrorCount	1.3.6.1.4.1.6247.4.8.5.3	Counter32	read-only	The number of the aborted frames from the Satellite interface plus the number of octet error frames. An octet error is when the received frame does not start on a byte boudary.
C32 cdmipWanFpgaRxBadAddrCount	1.3.6.1.4.1.6247.4.8.5.1	Counter32	read-only	The number of received frames from the Satellite interface that do not match any of the HDLC addresses or the broadcast address. If 'frame bypass' is enabled, then non-matching frames are not counted as having a bad address.
C32 cdmipWanFpgaRxHdlcCrcErrorCount	1.3.6.1.4.1.6247.4.8.5.5	Counter32	read-only	The number of received frames from the Satellite interface that failed the HDLC CRC check.
C32 cdmipWanFpgaRxHdlcHeaderCount	1.3.6.1.4.1.6247.4.8.5.7	Counter32	read-only	The count of HDLC header bytes received over the Satellite interface, including control, HDLC address, Flow ID, and CRC.
C32 cdmipWanFpgaRxHdlcPacketCount	1.3.6.1.4.1.6247.4.8.5.8	Counter32	read-only	The number of frames received over the Satellite interface.
C32 cdmipWanFpgaRxHdlcPayLoadCount	1.3.6.1.4.1.6247.4.8.5.6	Counter32	read-only	The count of payload bytes that were received over the Satellite interface, excluding any frame overhead.
C32 cdmipWanFpgaRxOverrunErrorCount	1.3.6.1.4.1.6247.4.8.5.4	Counter32	read-only	The number of received frames from the Satellite interface that exceeded a max. frame length of 2K bytes in length or overflowed the HDLC buffer.
C32 cdmipWanFpgaRxPktProcessorCrcErrorCount	1.3.6.1.4.1.6247.4.8.5.2	Counter32	read-only	The number of received frames from the Satellite interface that failed the packet processor CRC check.
cdmipWanFpgaStatistics	1.3.6.1.4.1.6247.4.8.5
C32 cdmipWanFpgaTxHdlcHeaderCount	1.3.6.1.4.1.6247.4.8.5.9	Counter32	read-only	The number of HDLC header bytes transmitted over the Satellite interface.
C32 cdmipWanFpgaTxHdlcPacketCount	1.3.6.1.4.1.6247.4.8.5.11	Counter32	read-only	The number of packets transmitted over the Satellite interface.
C32 cdmipWanFpgaTxHdlcPayLoadCount	1.3.6.1.4.1.6247.4.8.5.10	Counter32	read-only	The number of payload bytes transmitted over the Satellite interface.
INT cdmipWanFpgaWanBandwidthSaved	1.3.6.1.4.1.6247.4.8.5.16	INTEGER	read-only	The percentage (%) of Satellite bandwidth saved because of IP header and payload compression.
INT cdmipWanFpgaWanUtilization	1.3.6.1.4.1.6247.4.8.5.13	INTEGER	read-only	The percentage (%) of Tx bandwidth that is being utilized.
INT cdmipWorkingMode	1.3.6.1.4.1.6247.4.2.10	INTEGER	read-write	Configure the IP Card's working mode. The CDM-IP can operate in any of these modes. 1. Router - Small Network Mode: The system functions as router and uses the route table to determine how to forward packets in a small network HDLC address mode. The HDLC packet uses a 1 byte HDLC address. The valid values are from 1 to 254 (0x1 - 0xFE). 2. Router - Large Network Mode: The system functions as router and uses the route table to determine how to forward packets in a large network HDLC address mode. The HDLC packet uses a 2- byte HDLC address. The valid values are from 1 to 32766 (0x1 - 0x7FFE). 3. Router - Point to Point - The system functions as router and uses the route table to determine how to forward packets in a point-to-point HDLC address mode. The HDLC packet does not use a HDLC address. 4. Router - Vipersat Mode - The system functions in Vipersat mode. 5. EasyConnect mode - The system forwards all packets it receives. The HDLC packet does not use a HDLC address. * IMPORTANT NOTE * Changing Working mode requires the system to reboot. System configuration is saved before rebooting. Please make sure you are setting the correct value.

RFC description

Manages CDM-IP Controller for WAN/LAN statistics, QoS rules, and admin functions.

Start monitoring Comtech EF Data satellite modems with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CDMIPController

What Is CDMIPController?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description