SBE-MIB

All MIBs › SBE-MIB

Category: Generic / Unclassified

Description: Manages SBE series device configuration, interface status, and operational parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SBE-MIB?

SBE-MIB is a vendor-specific system-management MIB for SBE-series network routers, exposing baseline system identity and boot/configuration state rather than deep per-interface statistics. It provides objects for system identity (node name, contact, physical location, model, serial number), current date/time, and configuration state, including whether the running or RAM configuration has changed and whether it is locked. It supports monitoring both hardware and software status through objects like syBootInfo and syBootOrder, which reveal a recent reboot or the device's boot sequence, syRAMConfigurationChangedFlag/syConfigurationLockFlag for configuration integrity, and syActivatedLevel/syBaseActivationLevel for the device's currently active software feature/license tier. The presence of top-level "system" and "router" branches suggests it parallels standard SNMPv2 system MIB conventions. It is typically deployed on SBE-series router/network appliances where administrators need identity, boot state, and license/feature activation level visible via SNMP. Engineers can download the SBE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SBE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SBE-series network router/appliance

Monitoring Examples

An admin polls syModel and sySerialNumber to inventory a device, checks syBootInfo/syBootOrder to see whether the device recently rebooted or in what sequence its boot stages completed, and monitors syConfigurationLockFlag/syRAMConfigurationChangedFlag to catch an unsaved or locked configuration change; syActivatedLevel indicates which licensed feature tier is currently active on the router.

What Can Be Monitored

system node name and location
system date/time
configuration change/lock flag
boot information and boot order
device model and serial number
software activation/license level

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

From RFC1230-MIB

MacAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
sbe	1.3.6.1.4.1.1055
system	1.3.6.1.4.1.1055.1
OCT syDateTime	1.3.6.1.4.1.1055.1.1	OCTET STRING	read-write	Default value on nX: zero On nX: stored in clock chip Format: Century, year, month, day, hour, min, sec. each occupies one octet in binary value.
INT syRAMConfigurationChangedFlag	1.3.6.1.4.1.1055.1.3	INTEGER	read-only	Default value on nX: set to 'same' when booted from flash, 'different' otherwise On nX: (not needed?) in ram, field trial 2 This field is used by Workshop to determine if the RAM image currently being executed on the nX product is identical to the image in the LX's flash. Whenever part of the RAM image is changed (currently only via SNMP), this value is set to 'different' by the LX.
INT syConfigurationLockFlag	1.3.6.1.4.1.1055.1.5	INTEGER	read-write	Default value on nX: 'unlocked(2)' This field is used by Workshop to determine whether the nX unit is enabled to allow configuration. When this field is set to locked(1), nX rejects the SET requests for all mib entries except this one. The status of this field is also indicated by the lock LED on nX.
STR syModel	1.3.6.1.4.1.1055.1.7	DisplayString	read-only	Default value on nX: factory setting On nX: in flash, field trial 1 The product name, hardware revision, firmware revision, and kernel revision for the nX Node product. E.G. SoHo/HW4/FW3/SW1.0V1.0 Product names - SoHo, Central, ROUTEMAN, ROUTEMANXL Hardware Rev - HW Revision number, e.g. HW4 Firmware Rev - FW Revision number, e.g. FW3 Kernel Rev - SW Release-number Version-number, e.g. SW1.0V1.0 Note: for Central we will define a second variable, syCoprocessorModel.
INT syBootInfo	1.3.6.1.4.1.1055.1.10	INTEGER	read-only	THIS ITEM IS NOT IMPLEMENTED!
STR syActivatedLevel	1.3.6.1.4.1.1055.1.11	DisplayString	read-write	Software feature activation level information. This entry is maintained and used by Workshop.
OCT sySerialNumber	1.3.6.1.4.1.1055.1.12	OCTET STRING	read-only	A manufacturing only mib that will return the serial number of the board. This function is reserved for manufacturing test and may change as needed by manufacturing.
INT syBaseActivationLevel	1.3.6.1.4.1.1055.1.13	INTEGER	read-only	Base level software feature information. This entry is maintained by the nX unit and used by Workshop.
router	1.3.6.1.4.1.1055.2
routsys	1.3.6.1.4.1.1055.2.1
OCT syBootOrder	1.3.6.1.4.1.1055.2.1.1	OCTET STRING	read-write	enum values per octet: 1=Flash, 2=TFTP, 3=PCMCIA, 4=LAN, 0=none Default value on nX: (Flash) On nX: in flash This field has one octet for each boot source from which the nX product will attempt to boot. The first choice boot source is designated by the first byte, the second choice by the second byte, etc. In the first release there are only two boot choices, but future versions may have additional choices such as PCMCIA. If the nX detects that a boot choice is corrupted, it will ignore that choice and proceed to the next choice. The value 'none' is just used to fill any unused octets after the choices have been specified.
INT syMtuMru	1.3.6.1.4.1.1055.2.1.2	INTEGER	read-only	Default value on nX: 1500 On nX: both ram and flash, field trial 2 This field specifies the maximum size frame that the nX product will send or receive, either on the LAN or on a WAN port. The maximum for Ethernet is 1500, 1492 for 802.3 with SNAP. This is used by the nX product to detect error frames (i.e. too long) and during PPP negotiation. The actual transfer size is negotiated, by destination, when the connection is first made.
INT syEventToLogThreshold	1.3.6.1.4.1.1055.2.1.3	INTEGER	read-write	Default value on nX: 3 On nX: both ram and flash, field trial 2 All events generated by the nX product have an associated severity level which ranges from 1 to 10. The nX product puts events of this threshold level and above into its internal circular log file. Other events are discarded.
INT syEventToTrapThreshold	1.3.6.1.4.1.1055.2.1.5	INTEGER	read-write	Default value on nX: 6 On nX: both ram and flash, field trial 2 All events generated by the nX product have an associated severity level which ranges from 1 to 10. For events of this threshold level and above, the nX generates an SNMP trap.
INT syControlOperation	1.3.6.1.4.1.1055.2.1.7	INTEGER	read-write	Default value on nX: 'none' On nX: in ram, field trial 1 except for Clear-SNMP-statistics and Disable-port-after-call which are field trial 2 This object is set whenever Workshop wants the nX to perform an operation. Upon completion of the operation, the nX sets the value back to 'none'. Some operations use Control Variables as parameters for the operation. Any Control Variables must be set in the same frame as the Control Operation to insure that they are not changed by another Workshop before the operation is performed. After a Control Operation is started, the values in the Control Variables may no longer be valid. Reboot When the value is 'reboot', the nX performs an immediate reboot. Clear-SNMP-statistics When the value is 'clear-SNMP-statistics', the nX resets to zero all MIB statistics fields. Dialout When the value is 'dialout', the nX performs a dialout to the destination identified in Control Variable String One. Hangup When the value is 'hangup', the nX hangs up the non-leased line connection for the Destination identified in Control Variable String One. Enable port When the value is 'enable-port', the nX enables the port identified by Control Variable Integer One. Disable port When the value is 'disable-port', the nX disables the port identified by Control Variable Integer One. Disable-port-after-call When the value is 'disable-port-after-call', the nX disables the port identified by Control Variable Integer One immediately after the current connection terminates. This option allows gracefully taking the nX out of operation (except for leased lines). This option is not applicable to leased lines. Crash When the value is 'crash', the nX stores its RAM memory contents to a PCMCIA card for off-line debugging. Change-password When the value is 'change-password', the nX changes both the RAM and Flash password for a user. The Control Variable String One contains the following zero terminated strings in order: User Name, old User Password, and new User Password. This is the only way to change passwords, except when defining a new user. RAM-to-Flash When the value is 'RAM-to-Flash', the nX stores object values in RAM into Flash. start-tftp-download Reset-port Hangup the port, if necessary and reinitialize the modem. Display-IP-Routes Show IP routes via event logger. Display-IPX-Networks Show IPX Networks via event logger. Display-IPX-Servers Show IPX Servers via event logger.
OCT syControlVariableStringOne	1.3.6.1.4.1.1055.2.1.8	OCTET STRING	read-write	Default Value on nX: N/A On nX: in ram, field trial 1 This object is used to store a DisplayString parameter to a control operation. Once the control operation is started, the value is unspecified.
INT syControlVariableIntegerOne	1.3.6.1.4.1.1055.2.1.9	INTEGER	read-write	Default Value on nX: N/A On nX: in ram, field trial 1 This object is used to store an Integer parameter to a control operation. Once the control operation is started, the value is unspecified.
INT syDialinAuthentication	1.3.6.1.4.1.1055.2.1.10	INTEGER	read-write	Default value on nX: 'none' On nX: both ram and flash. This field identifies the type of authentication negotiation that is to be performed during dialin to this destination.
INT syEventToSpeakThreshold	1.3.6.1.4.1.1055.2.1.11	INTEGER	read-write	Default value on nX: 6 On nX: both ram and flash, field trial 2 All events generated by the nX product have an associated severity level which ranges from 1 to 10. For events of this threshold level and above, the nX speaks the error code to the speaker.
INT syNumberOfTimesToSpeak	1.3.6.1.4.1.1055.2.1.12	INTEGER	read-write	Default value on nX: 3 On nX: both ram and flash, field trial 2 This item specifies the number of times an error code is spoken
INT sySaveRamToFlashState	1.3.6.1.4.1.1055.2.1.13	INTEGER	read-only	This item specifies the state of the operation ram-to-Flash in the item syControlOperation. The valid states are: updating and idle. updating state indicates that a write to flash operation is in progress, idle state indicates idle.
INT syDialbackRetryInterval	1.3.6.1.4.1.1055.2.1.14	INTEGER	read-write	This item specifies the number of seconds to pause before the next dialback call from Soho will be made. Default = 10
INT syDialbackRetryLimit	1.3.6.1.4.1.1055.2.1.15	INTEGER	read-write	This item specifies the number of times that Soho will retry dialback call from Soho. Default is 3.
INT syReverseCallbackTimeout	1.3.6.1.4.1.1055.2.1.16	INTEGER	read-write	Default value on nX: 60 (seconds) Specifies the number of seconds to wait for an expected reverse callback before redialing.
bridge	1.3.6.1.4.1.1055.2.2
INT syBridgeConfiguredFlag	1.3.6.1.4.1.1055.2.2.1	INTEGER	read-write	Default value on nX: 'yes' On nX: both ram and flash, field trial 2 If this object is 'no', syBridgeFilterFlag will be returned as 'other' by default regardless of the value that is previously set. If this is 'yes', syBridgeFilterFlag governs the bridging rule.
INT syBridgeFilterFlag	1.3.6.1.4.1.1055.2.2.2	INTEGER	read-write	Default value on nX: 'all' On nX: both ram and flash, field trial 2 This value indicates the bridging rule for this nX product, whether to include or exclude packets for the protocols indicated in the Bridge Sub-Table. If the value is 'all', all protocols will be bridged. If the value is 'include', only the protocols listed in the Bridge Sub-Table are to be bridged over this port. If the value is 'exclude', all packets except for the protocols listed in the Bridge Sub-Table are to be bridged.
INT syBridgePriority	1.3.6.1.4.1.1055.2.2.3	INTEGER	read-write	Default value on nX: 32768 On nX: both ram and flash Used by the Spanning Tree Algorithm to determine who is the root bridge in the network.
syBridgeTable	1.3.6.1.4.1.1055.2.2.4		not-accessible	Bridge table - one copy
syBridgeEntry	1.3.6.1.4.1.1055.2.2.4.1		not-accessible	The bridge table information for one protocol.
INT syBridgeStatus	1.3.6.1.4.1.1055.2.2.4.1.1	INTEGER	read-write	Indication of whether or not a valid entry.
INT syBridgeProtocol	1.3.6.1.4.1.1055.2.2.4.1.2	INTEGER	read-only	Default value on nX: none On nX: both ram and flash, field trial 2 This column item contains the protocol number for a protocol to be bridged. Bridging rules are governed by syBridgeFlag.
ip	1.3.6.1.4.1.1055.2.3
INT ipConfiguredFlag	1.3.6.1.4.1.1055.2.3.1	INTEGER	read-write	Default value on nX: 'no' On nX: both ram and flash, field trial 1 This object is 'no' if IP is not configured for this LX-Product, 'yes' if it is configured.
IP ipLANAddress	1.3.6.1.4.1.1055.2.3.2	IpAddress	read-write	Default value on nX: 0 On nX: both ram and flash, field trial 1 If IP is configured, this object contains the IP address for the nX product's ethernet port and the nX product itself. The user must supply this value if IP is configured. When IP is configured this value must not be 0.
IP ipLANSubnetMask	1.3.6.1.4.1.1055.2.3.3	IpAddress	read-write	Default value on nX: N/A Default value in Workshop: 0 On nX: both ram and flash, field trial 1 If IP is configured, this object contains the subnet mask which the nX product will use for determining which packets are to be sent out over this LAN port. (A packet's IP address is 'anded' with the subnet mask and the result compared against the port's IP address. If there is a match, the packet is sent over the port, otherwise it isn't.)
IP ipBroadcastAddress	1.3.6.1.4.1.1055.2.3.4	IpAddress	read-write	Default value on nX: 0 Default value in Workshop: 0 On nX: both ram and flash, field trial 1 If IP is configured, this object contains the IP address which the nX product will use for sending broadcast data. (The nX listens for broadcast data on broadcast addresses with both 0's and all 1's). A zero value means no broadcasts can be sent. This is used for sending RIP advertisements and for indicating which broadcasts are to be forwarded across ports.
IP ipDefaultGateway	1.3.6.1.4.1.1055.2.3.5	IpAddress	read-write	Default value on nX: N/A Default value in Workshop: 0 On nX: both ram and flash, field trial 2 If IP is configured, this object contains the network address to which the nX product will send all packets that it cannot determine a route for the packet from its routing tables (both static and dynamic).
INT ipRipReceiveAdvertisementFlag	1.3.6.1.4.1.1055.2.3.6	INTEGER	read-write	Default value on nX: 'yes' On nX: both ram and flash, field trial 2 If IP is configured, this object determines whether or not the nX product will accept IP RIP (Routing Information Protocol) from other routers on the network. Advertisements received will be added to the nX product's dynamic routing table.
INT ipRipSendInterval	1.3.6.1.4.1.1055.2.3.7	INTEGER	read-write	Default value on nX: 30 On nX: both ram and flash, field trial 2 If IP is configured, this object determines time, in seconds, between nX broadcasts of the IP RIP destination information in its routing tables. If the value equals 0, RIP transmissions are not sent.
INT ipDefaultGatewayType	1.3.6.1.4.1.1055.2.3.8	INTEGER	read-write	Default value on nX: NONE On nX: both ram and flash, field trial 2 If nX cannot determine a route for the packet from its routing table (both static and dynamic), the packet will be sent to a Default Gateway. If ipDefaultGatewayType is LAN, ipDefaultGateway address will be useed. Otherwise, the Default Gateway is located at WAN port, the packet will be forwarded to the destination defined in ipWanDestinationName or ipWanUserName.
STR ipWanDestinationName	1.3.6.1.4.1.1055.2.3.9	DisplayString	read-write	Same as destName in the Destination Table.
STR ipWanUserName	1.3.6.1.4.1.1055.2.3.10	DisplayString	read-write	Same as userName in the User Table.
INT ipStaticRouteMaxEntry	1.3.6.1.4.1.1055.2.3.11	INTEGER	read-only	maximum # of entry allowed in the ipStaticRouteTable. Default to 32.
ipStaticRouteTable	1.3.6.1.4.1.1055.2.3.12		not-accessible	IP Static Route table - one copy per IP port.
ipStaticRouteEntry	1.3.6.1.4.1.1055.2.3.12.1		not-accessible	The static route information for one route for this port.
INT ipStaticRouteStatus	1.3.6.1.4.1.1055.2.3.12.1.1	INTEGER	read-write	Indication of whether or not a valid entry.
IP ipStaticRouteDestinationAddress	1.3.6.1.4.1.1055.2.3.12.1.2	IpAddress	read-only	This is a destination network or host IP address. Packets that the nX product processes for this address will be routed as indicated by the remaining entries in this row. This value has already been 'anded' with the IP Destination Subnet Mask.
IP ipStaticRouteDestinationSubnetMask	1.3.6.1.4.1.1055.2.3.12.1.3	IpAddress	read-write	Workshop should display by default the subnet mask based on class of destination IP address, the nX should not assume any default subnet value. This subnet mask is applied to destination address in packets processed by the nX product and then the resulting value is compared against the IP Destination Address. If a match is found, the packet is forwarded over the indicated destination interface.
INT ipStaticRouteDestinationHopCount	1.3.6.1.4.1.1055.2.3.12.1.4	INTEGER	read-write	The value of this object indicates the number of hops between the nX product and the IP Destination Address. The hop count is often used as an indicator of the relative cost for using this route. This will be used by the LX to optimize the use of routes learned. By IP convention, if the hop count equals 16 the routing entry is disabled.
STR ipStaticRouteDestinationName	1.3.6.1.4.1.1055.2.3.12.1.5	DisplayString	read-write	Same as destName in the Destination Table.
INT ipStaticRouteNetworkInterface	1.3.6.1.4.1.1055.2.3.12.1.6	INTEGER	read-write	Indication of which interface type to route this packet to. If LAN is defined, ipStaticRouteGateway must be defined. Otherwise, at least one of ipStaticRouteUserName and ipStaticRouteDestinationName must be defined.
STR ipStaticRouteUserName	1.3.6.1.4.1.1055.2.3.12.1.7	DisplayString	read-write	Same as userName in the User Table.
IP ipStaticRouteGateway	1.3.6.1.4.1.1055.2.3.12.1.8	IpAddress	read-write	This is the Gateway IP address of the static route.
INT ipDefaultGatewayIfType	1.3.6.1.4.1.1055.2.3.13	INTEGER	read-write	Default value on nX: NONE If nX cannot determine a route for the packet from its routing table (both static and dynamic), the packet will be sent to a Default Gateway. If ipDefaultGatewayType is LAN, ipDefaultGateway address will be useed. Otherwise, the Default Gateway is located at WAN port, the packet will be forwarded to the destination defined in ipWanDestinationName or ipWanUserName.
INT ipBroadcastForwardTypes	1.3.6.1.4.1.1055.2.3.14	INTEGER	read-write	Default value on nX: 0 This is a bit encoded value representing the types of IP broadcast forwarding over WAN to be enabled. This is a global setting for the NX. The mib entry destDialoutProtoSupport is used to control the IP broadcast forwarding to an invidual site. The encoded values are: NetBIOS(2), DNS(4), DHCP/BOOTP(8). Any combination of these values or NOBCASTFWD(1) are the only valid values.
ipx	1.3.6.1.4.1.1055.2.4
INT ipxConfiguredFlag	1.3.6.1.4.1.1055.2.4.1	INTEGER	read-write	Default value on nX: 'ipx-and-auto-learn-both-off (1)' On nX: both ram and flash, This object reflects the state of ipx and auto-learning configuration as described by the names of the values.
INT ipxNetbios	1.3.6.1.4.1.1055.2.4.8	INTEGER	read-write	Default value on nX: no (1) This object reflects the state of NetBIOS (IPX Type20) frame forwarding for the NX. NetBIOS forwarding is enabled for a specific site only when this object is set to 'yes' and NetBIOS/IPX bit is set in the destDialoutProtoSupport object for the site.
ipxMultiFrameTable	1.3.6.1.4.1.1055.2.4.9		not-accessible	IPX multifram type support, the table contains fix size of 4 entries. They can not be added or deleted.
ipxMultiFrameEntry	1.3.6.1.4.1.1055.2.4.9.1		not-accessible	The community information for this community.
INT ipxMultiFrameStatus	1.3.6.1.4.1.1055.2.4.9.1.1	INTEGER	read-write	Indication of whether or not a valid entry. User can only use Modify
INT ipxMultiFrameType	1.3.6.1.4.1.1055.2.4.9.1.2	INTEGER	read-only	Default value on nX: IEEE 802.2
INT ipxMultiFrameSelectFlag	1.3.6.1.4.1.1055.2.4.9.1.3	INTEGER	read-write	Default value on nX: there must be at least a entry is = yes
OCT ipxMultiFrameNetworkAddress	1.3.6.1.4.1.1055.2.4.9.1.4	OCTET STRING	read-write	Default value on nX: 0 If IPX Manual Set Network Address is set to 'yes', this object specifies the IPX Network Address that the nX product will use for packets sent to it. Normally the IPX Node Address is automatically taken from the network.
INT ipxNetAddressAutoLearnStateCounter	1.3.6.1.4.1.1055.2.4.11	INTEGER	read-only	Default value on nX: 0 If IPX is configured, and Auto learn is Yes. this object determines the time (in sec) remaining in the IPX auto learn phase. If the value is non-zero, nX auto learn is in progress. Workshop will continue to poll this mib item, and ipxMultiFrameTable.
wan	1.3.6.1.4.1.1055.2.5
wanPortTable	1.3.6.1.4.1.1055.2.5.1		not-accessible	Each WAN port's information is contained in a row in a SNMP table. The following describes the columns in the table. Each row is uniquely identified by its Wan Port Number. (See also Port Sub-Data.)
wanPortEntry	1.3.6.1.4.1.1055.2.5.1.2		not-accessible	The WAN table information for one WAN port.
INT wanPortEntryStatus	1.3.6.1.4.1.1055.2.5.1.2.1	INTEGER	read-write	Indication of whether or not a valid entry.
INT wanPortNumber	1.3.6.1.4.1.1055.2.5.1.2.2	INTEGER	read-only	Default value on nX: ascending integer, one for each hardware WAN port: 1, 2, 3A, 3B, 4A, and 4B. On nX: both ram and flash, field trial 1 This field is used to identify the Wan port to which the information in this row of the table applies.
INT wanPortEnabled	1.3.6.1.4.1.1055.2.5.1.2.3	INTEGER	read-only	Default value on nX: disabled On nX: both ram and flash, field trial 1 If this value is 'enabled', the Wan port is enabled. If this value is 'disabled', if the Wan port is disabled.
IP wanDefaultDialinIPAddress	1.3.6.1.4.1.1055.2.5.1.2.4	IpAddress	read-write	Default value on nX: all zero On nX: both ram and flash, field trial 1 If IP is configured, this field is required and is used as the default IP address of the WAN port on dialin unless overridden during dialin either by an IP address from the User Table or by PPP negotiation. The same value needs to be configured at the other end of the WAN link (this could be a cause of user error, but there is no way around it).
IP wanDefaultDialinSubnetMask	1.3.6.1.4.1.1055.2.5.1.2.5	IpAddress	read-write	Default value on nX: all zero Default value in Workshop: 1's, based on Default Dialin IP Address class On nX: both ram and flash, field trial 1 If the Default Dialin IP Address is used, this object is used as its Subnet Mask. Subnet masks allow the user to divide the local network into sub-networks by specifying a subnet mask. The subnet mask, combined with the Dialin IP Address field, determines which frames (packets) are sent across the WAN port during dialin. The subnet masks are all 1's from the left for a specified number of bits. On Workshop, the subnet mask will be entered as a number of bits from 0 to 32.
OCT wanDefaultIPXNetworkAddress	1.3.6.1.4.1.1055.2.5.1.2.6	OCTET STRING	read-only	Default value on nX: 0 On nX: in ram, field trial 1 If IPX is configured, this field indicates which IPX network address is being used by this port. The nX will automatically generate an address to be used during dialout and, during dialin, will accept the address from the calling node. (The nX products use the SAP tables they dynamically build to determined which network numbers are already in use.)
OCT wanDefaultDialinIPXNodeAddress	1.3.6.1.4.1.1055.2.5.1.2.7	OCTET STRING	read-only	Default value on nX: 0 On nX: in ram, field trial 1 If IPX is configured, this field specifies the IPX node address that is being used by this port. The nX will automatically generate an address to be used during dialout and, during dialin, will accept the address from the calling node.
INT wanDialinAllowedFlag	1.3.6.1.4.1.1055.2.5.1.2.8	INTEGER	read-write	Default value on nX : 'yes' On nX: both ram and flash, field trial 2 If this flag is 'yes', dialin access is allowed on this port.
INT wanDialoutAllowedFlag	1.3.6.1.4.1.1055.2.5.1.2.9	INTEGER	read-write	Default value on nX : 'yes' On nX: both ram and flash, field trial 2 If this flag is 'yes', dialout is allowed on this port.
INT wanLinkLayerType	1.3.6.1.4.1.1055.2.5.1.2.10	INTEGER	read-write	Default value on nX: async On nX: both ram and flash, field trial 1 This object identifies the type of communication link that is used by this WAN port. Some data link types require further qualification.
INT wanLinkLayerNRZFlag	1.3.6.1.4.1.1055.2.5.1.2.11	INTEGER	read-write	Default value on nX: nrz On nX: both ram and flash If appropriate for the Link Line Type, this flag identifies whether the line is nrz or nrzi. (See Destination NRZ Flag.)
INT wanLinkLayerProtocolType	1.3.6.1.4.1.1055.2.5.1.2.12	INTEGER	read-write	Default value on nX: ppp On nX: both ram and flash, This flag identifies whether the Link Line Type is ppp. Other options are not supported at this time.
INT wanLinkDialupFlag	1.3.6.1.4.1.1055.2.5.1.2.13	INTEGER	read-write	Default value on nX: dialup dtr-dial(3) is obsolete (3/4/96) On nX: both ram and flash, field trial 1 (may be encoded into Link Layer Type) If appropriate for the Link Line Type, this flag identifies whether the line is dialup (switched), dedicated, DTR dial, or ISDN dialup link.
STR wanModemName	1.3.6.1.4.1.1055.2.5.1.2.14	DisplayString	read-write	Default value on nX: empty On nX: both ram and flash, field trial 1 This object contains the ASCII name of the modem. It is used by Workshop to determine the initialization modem string and maximum speed for this modem. This object is not used by the nX product. (If possible on Workshop, this field will be changed to something shorter, like an integer - if not will try to combine with PCMCIA Card Name.)
INT wanModemSpeed	1.3.6.1.4.1.1055.2.5.1.2.15	INTEGER	read-write	Default value on nX: 9600 On nX: both ram and flash, field trial 1 This object contains an indicator of the speed at which the nX product should communicate with the modem. This value cannot be larger than that obtained from the Modem File using the Modem Name. (Note: The UART does not support 14400 or 28800 directly so a higher speed must be specified and hardware handshake will be used to prevent overruns.)
STR wanModemInitializationString	1.3.6.1.4.1.1055.2.5.1.2.16	DisplayString	read-write	Default value on nX: empty On nX: both ram and flash, field trial 1 This object contains the ASCII string that is to be sent to the modem whenever the modem is to be initialized.
STR wanModemDialPrefix	1.3.6.1.4.1.1055.2.5.1.2.17	DisplayString	read-write	Default value on nX: empty On nX: both ram and flash, field trial 1 This is set by the user. It contains the modem's dial command (e.g. ATDT or ATDP) possibly suffixed with the dial prefix, if any, to obtain an outside phone line. (Note that the user could include the dial prefix in the Destination Phone Number instead.) For example, at SBE this would be set to '8' if the nX product's phone lines were inside lines. This string is long so it can include other items, such as billing codes, if necessary. (Will contain codes to differentiate V.25 dialing from ATDT dialing.)
INT wanPortType	1.3.6.1.4.1.1055.2.5.1.2.18	INTEGER	read-only	Default value on nX: determined by hardware Workshop no longer sets this field This value indicates whether the port is PCMCIA, or a D-shell connection - either RS232 or V.35.
STR wanPCMCIACardName	1.3.6.1.4.1.1055.2.5.1.2.19	DisplayString	read-only	Default value on nX: empty string if card not present, else product information from card On nX: from 'ram' (actually hardware), field trial 1 Workshop no longer display this field This object returns the product information read from a PCMCIA card. If the returned value is a 0 length string, then the PCMCIA slot is empty. (60 characters available from hardware.)
INT wanIpRipReceiveAdvertisementFlag	1.3.6.1.4.1.1055.2.5.1.2.20	INTEGER	read-write	Default value on nX: 'yes' On nX: both ram and flash, field trial 2 If IP is configured, this object determines whether or not the nX product will accept IP RIP (Routing Information Protocol) from other routers on the network. Advertisements received will be added to the nX product's dynamic routing table.
INT wanIpRipSendInterval	1.3.6.1.4.1.1055.2.5.1.2.21	INTEGER	read-write	Default value on nX: 30 On nX: both ram and flash, field trial 2 If IP is configured, this object determines time, in seconds, between nX broadcasts of the IP RIP destination information in its routing tables. If the value equals 0, RIP transmissions are not sent.
INT wanIpxRipReceiveBroadcastFlag	1.3.6.1.4.1.1055.2.5.1.2.22	INTEGER	read-write	Default value on nX: ''yes' On nX: both ram and flash, field trial 2 If IPX is configured, this object determines whether or not the nX product will accept IPX RIP (Routing Information Protocol) from other routers on the network. Broadcasts received will be added to the nX product's dynamic routing table.
INT wanIpxRipSendInterval	1.3.6.1.4.1.1055.2.5.1.2.23	INTEGER	read-write	Default value on nX: 60 On nX: both ram and flash, field trial 2 If IPX is configured, this object determines time, in seconds, between nX broadcasts of the IPX RIP destination information in its routing tables. If the value equals 0, RIP transmissions are not sent.
INT wanIpxSapReceiveAdvertisementFlag	1.3.6.1.4.1.1055.2.5.1.2.24	INTEGER	read-write	Default value on nX: ''yes' On nX: both ram and flash, field trial 2 If IPX is configured, this object determines whether or not the nX product will accept IPX SAP advertisements from other routers on the network. Advertisements received will be added to the nX product's dynamic SAP table.
INT wanIpxSapSendInterval	1.3.6.1.4.1.1055.2.5.1.2.25	INTEGER	read-write	Default value on nX: 60 On nX: both ram and flash, field trial 2 If IPX is configured, this object determines time, in seconds, between nX broadcasts of the IPX SAP information in its routing tables. If the value equals 0, SAP advertisements are not sent.
INT wanIpxNetbios	1.3.6.1.4.1.1055.2.5.1.2.26	INTEGER	read-write	Default value on nX: 'no' On nX: both ram and flash, field trial 2 If IPX is configured, this object determines if NetBIOS broadcasts are to be forwarded across interfaces. (It appears this is only needed if there is an application on the network that initiates a connection with a dialin client, see Shiva LanRover, page 10-6.)
INT wanISDNSwitchType	1.3.6.1.4.1.1055.2.5.1.2.27	INTEGER	read-write	The particular protocol type supported by the switch providing access to the ISDN network to which this subscriber interface is connected. Note: this entry definition is borrowed from the isdnSubTblSwitchType of the ISDN MIB Internet Draft
STR wanISDNCallingPhoneNoB1	1.3.6.1.4.1.1055.2.5.1.2.28	DisplayString	read-write	Default value on nX: empty This item contains the calling phone number for the ISDN B1 channel.
STR wanISDNCallingPhoneNoB2	1.3.6.1.4.1.1055.2.5.1.2.29	DisplayString	read-write	Default value on nX: empty This item contains the calling phone number for the ISDN B1 channel.
STR wanISDNSPID1	1.3.6.1.4.1.1055.2.5.1.2.30	DisplayString	read-write	Default value on nX: empty This item contains the Service Profile Identifiers (SPID) for the ISDN B1 channel.
STR wanISDNSPID2	1.3.6.1.4.1.1055.2.5.1.2.31	DisplayString	read-write	Default value on nX: empty This item contains the Service Profile Identifiers (SPID) for the ISDN B2 channel.
INT wanPortGroup	1.3.6.1.4.1.1055.2.5.1.2.32	INTEGER	read-write	Default value on nX: non-group(2) This field is used to identify wether the Wan port is part of the Hunt Group. Port group is used as hunt group in TSD for reserving wan link capacity.
STR wanISDNSubAddress1	1.3.6.1.4.1.1055.2.5.1.2.33	DisplayString	read-write	Default value on nX: empty This item contains the subaddress for the ISDN B1 channel.
STR wanISDNSubAddress2	1.3.6.1.4.1.1055.2.5.1.2.34	DisplayString	read-write	Default value on nX: empty This item contains the subaddress for the ISDN B2 channel.
INT wanISDNNTTCard	1.3.6.1.4.1.1055.2.5.1.2.35	INTEGER	read-write	Default value on nX: no(1) This item indicates whether this is an NTT ISDN card.
INT wanISDNChannels	1.3.6.1.4.1.1055.2.5.1.2.36	INTEGER	read-write	Default value on nX: oneb(1) This item indicates the number B channels supported by the ISDN card.
INT wanEnableDataCompression	1.3.6.1.4.1.1055.2.5.1.2.37	INTEGER	read-write	Default value on nX: no. this entry indicates whether to perform data compression over the ppp connection.
INT wanISDNChannelSpeed	1.3.6.1.4.1.1055.2.5.1.2.38	INTEGER	read-write	Default value on nX: cs64. This entry is used to configure the B channel speed of the ISDN card.
INT wanUsageMode	1.3.6.1.4.1.1055.2.5.1.2.39	INTEGER	read-write	Default value on nX: 1 This value indicates how the port is used for modem pooling. If 2 or 3 is set, the GSN and SSN also must be set. Note: This is a bit mapped field.
STR wanModemPoolGSN	1.3.6.1.4.1.1055.2.5.1.2.40	DisplayString	read-write	The General Service Name used for this port. Used for Modem pooling
STR wanModemPoolSSN	1.3.6.1.4.1.1055.2.5.1.2.41	DisplayString	read-write	The Specific Service Name used for this port. Used for Modem pooling
wanIPAddressTable	1.3.6.1.4.1.1055.2.5.2		not-accessible	WanIPAddress table - one copy
wanIPAddressEntry	1.3.6.1.4.1.1055.2.5.2.1		not-accessible
INT wanIPAddressStatus	1.3.6.1.4.1.1055.2.5.2.1.1	INTEGER	read-write	Indication of whether or not a valid entry.
IP wanIPAddress	1.3.6.1.4.1.1055.2.5.2.1.2	IpAddress	read-only	Default value on nX: 0 On nX: both ram and flash, field trial 2 This item specifies an IP address in the shared pool for remote dial-in user.
wanStatPortTable	1.3.6.1.4.1.1055.2.5.3		not-accessible	Each WAN port's State and Statistical information is contained in a row in a SNMP table
wanStatPortEntry	1.3.6.1.4.1.1055.2.5.3.1		not-accessible	The WAN table information for one WAN port.
INT wanStatPortEntryStatus	1.3.6.1.4.1.1055.2.5.3.1.1	INTEGER	read-write	Indication of whether or not a valid entry. This entry is used only to maintain uniformity of all table structures. User can neither delete nor add any entries in the table. Upon query, nX shall always return valid.
INT wanStatPortNumber	1.3.6.1.4.1.1055.2.5.3.1.2	INTEGER	read-only	Same as in wanPortNumber.
INT wanStatPortState	1.3.6.1.4.1.1055.2.5.3.1.3	INTEGER	read-only	Default value on nX: disconnected.
STR wanStatPortUserName	1.3.6.1.4.1.1055.2.5.3.1.4	DisplayString	read-only	Currently connected Destination name or user name. Null if unknown.
INT wanStatPortFrameTransmitted	1.3.6.1.4.1.1055.2.5.3.1.5	INTEGER	read-write	# of frames transmitted out of this port.
INT wanStatPortFrameReceived	1.3.6.1.4.1.1055.2.5.3.1.6	INTEGER	read-write	# of frames received from this port.
INT wanStatPortTransmitError	1.3.6.1.4.1.1055.2.5.3.1.7	INTEGER	read-write	# of transmit errors detected at this port.
INT wanStatPortReceiveError	1.3.6.1.4.1.1055.2.5.3.1.8	INTEGER	read-write	# of receive errors detected at this port.
INT wanStatPortTransmitQueueFull	1.3.6.1.4.1.1055.2.5.3.1.9	INTEGER	read-write	# of times transmit queue full detected at this port.
INT wanStatPortCallOriginated	1.3.6.1.4.1.1055.2.5.3.1.10	INTEGER	read-write	# of calls originated from this port. Includes both success and fail.
INT wanStatPortCallAnswered	1.3.6.1.4.1.1055.2.5.3.1.11	INTEGER	read-write	# of answers succeeded at this port.
INT wanStatPortNoDialTone	1.3.6.1.4.1.1055.2.5.3.1.12	INTEGER	read-write	# of calls failed due to no dial tone. also counted also in CallOriginated
INT wanStatPortNoAnswer	1.3.6.1.4.1.1055.2.5.3.1.13	INTEGER	read-write	# of calls failed due to no answer from remote. also counted also in CallOriginated
INT wanStatPortBusyDetected	1.3.6.1.4.1.1055.2.5.3.1.14	INTEGER	read-write	# of calls failed due to line busy at remote. also counted also in CallOriginated
INT wanStatPortNoCarrier	1.3.6.1.4.1.1055.2.5.3.1.15	INTEGER	read-write	# of calls failed due to no carrier. also counted also in CallOriginated
INT wanStatPortModemSignal	1.3.6.1.4.1.1055.2.5.3.1.16	INTEGER	read-only	Modem signal state. Bit masked DCD = 1, CTS =2, DTR = 4, RTS = 8, DSR =16 Bit state: 1 = On
INT wanStatPortConnDirection	1.3.6.1.4.1.1055.2.5.3.1.17	INTEGER	read-only	Direction of the connection
INT wanStatPortProtoUp	1.3.6.1.4.1.1055.2.5.3.1.18	INTEGER	read-only	This item is a bit encoded value representing various protocols, which are currently up over this connection. The encoded values are: IP(1), IPX(2), Bridging(4), Compression(8). Any combinations of these values are valid.
INT wanIPAddressMaxEntry	1.3.6.1.4.1.1055.2.5.4	INTEGER	read-only	maximum # of entry allowed in the wanIPAddressTable.
destination	1.3.6.1.4.1.1055.2.6
destTable	1.3.6.1.4.1.1055.2.6.1		not-accessible	Destination table - one copy
destEntry	1.3.6.1.4.1.1055.2.6.1.1		not-accessible	The information for one destination.
INT destStatus	1.3.6.1.4.1.1055.2.6.1.1.1	INTEGER	read-write	Indication of whether or not a valid entry.
STR destName	1.3.6.1.4.1.1055.2.6.1.1.2	DisplayString	read-only	Default value on nX: none On nX: both ram and flash, field trial 1 This item contains a user supplied identification for this destination. This should be something meaningful to the user, such as 'Home Office'. In a later release, User Table entries will include a destination field for dialout.
INT destType	1.3.6.1.4.1.1055.2.6.1.1.3	INTEGER	read-write	Default value on nX: Lan-to-Lan On nX: (not necessary in first release) both ram and flash, field trial 2 This item indicates whether the destination is a LAN or remote access. A Lan destination indicates Lan-to-Lan traffic over the link. All destinations are PPP serial communication. There will be other types, e.g. Remote-access, in later versions of the LX.
STR destDialoutPhoneNumber	1.3.6.1.4.1.1055.2.6.1.1.4	DisplayString	read-write	Default value on nX: empty On nX: both ram and flash, field trial 1 This item contains the phone number that is to be used to call the destination. This string contains just the AT command set characters for the phone number. During dialout, the nX forms the entire dialout string by prefixing this item with the Modem Dial Prefix.
INT destDialoutProtoSupport	1.3.6.1.4.1.1055.2.6.1.1.5	INTEGER	read-write	Default value on nX: 0 On nX: both ram and flash, This item is a bit encoded value representing various protocols to be enabled during the establishment of a WAN connection. The encoded values are: IP(1), IPX(2), Bridging(4), NetBIOS/IPX(8), IPBCASTFWD(16). Any combination of IP, IPX and Bridging is valid. NetBIOS/IPX is valid only if IPX bit is set. IPBCASTFWD is valid only if IP bit is set. Value zero is invalid
INT destDialoutIpxSupport	1.3.6.1.4.1.1055.2.6.1.1.6	INTEGER	read-write	NOTE: THIS FIELD IS NO LONGER IN USE. The field destDialoutProtoSupport is used to encode all protocols supported. Default value on nX: same as IP Configured Flag On nX: both ram and flash This item equals 'yes' if the dialout destination supports IPX, and 'no' otherwise. No IPX traffic will be routed or bridged to this destination if the value is 'no'. The IPX Configured Flag must be 'yes' for this field to be 'yes'.
INT destDialoutModemSpeed	1.3.6.1.4.1.1055.2.6.1.1.7	INTEGER	read-write	Default value on nX: 'unspecified' On nX: both ram and flash, This item allows the user to override the Modem Speed set up for the port for dialout calls to this destination. If the value of this item is 'unspecified', then the Modem Speed for the port is used. The user might specify this to shorten the time it takes for the modems to negotiate speed.
INT destPppMtuMru	1.3.6.1.4.1.1055.2.6.1.1.8	INTEGER	read-write	Default value on nX: 1500 On nX: both ram and flash, field trial 2 This field can be used to override the global MTR/MTU. The user should set this field if the destination or the Wan link has special requirements. Any value less than the minimum value allowed for a port's MTR/MRU will be interpreted as an unspecified value and the MTR/MRU value for the nX will be used. (Perhaps the user could be asked for line quality and the nX or Workshop automatically determine MTU/MRU.)
INT destDialoutHandshake	1.3.6.1.4.1.1055.2.6.1.1.9	INTEGER	read-write	Default value on nX: 'none' On nX: both ram and flash, 'none' and 'PAP' for field trial 1 This field identifies the type of authorization negotiation that is to be performed during dialout to this destination. (On dialin, the handshake is determined by the caller.)
STR destDialoutUserName	1.3.6.1.4.1.1055.2.6.1.1.10	DisplayString	read-write	Default value on nX: 0 On nX: both ram and flash, field trial 1 This value identifies a User Name for PAP or CHAP dialout to this destination. This entry is only valid if Destination Handshake if a value other than 'none'.
STR destDialoutPassword	1.3.6.1.4.1.1055.2.6.1.1.11	DisplayString	read-write	Default value on nX: 0 On nX: both ram and flash, field trial 1 This value identifies the user password for PAP or CHAP dialout to this destination. This entry is only valid if Destination Handshake if a value other than 'none'.
INT destPorts	1.3.6.1.4.1.1055.2.6.1.1.12	INTEGER	read-write	Default Value on nX: 0. This field indicates the port number associated with this site, if the link characteristic wanLinkDialupFlag is set to dedicated(2).
INT destMaximumDialoutConnectTime	1.3.6.1.4.1.1055.2.6.1.1.13	INTEGER	read-write	Default value on nX: 0 On nX: both ram and flash, field trial 1 This object contains, in minutes, the maximum time to leave this connection active for dialout. After the time elapses, the nX will automatically hangup the connection, assuming the user has not already manually terminated the connection. A value of zero means there is no time limit. For any given call, this time by be shortened because of a value in the User Maximum Dialout Connect Time object. (For dialin, the maximum connect time comes from the User Table.) (If we require a default user name for the destination, we could take the maximum dialout time from the User Table.)
INT destDialoutStatus	1.3.6.1.4.1.1055.2.6.1.1.14	INTEGER	read-only	Default value on nX: none This item is used by the Workshop to determine the status of a dialout for this destination.
OCT destDialoutSchedule	1.3.6.1.4.1.1055.2.6.1.1.15	OCTET STRING	read-write	Default value on nX: 0 On nX: both ram and flash, field trial 2 This is a one-week bit map, with one bit for every 15 minutes. The string is organized a 8 groups of 12 bytes (96 bits), one group for each day of the week plus the 8th for all holidays, starting with Sunday, Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, Holiday. The first bit in each group is for midnight (12:00 AM) to 12:15 AM, the next for 12:15 AM to 12:30 AM, etc. If the bit for a time interval equals 1, a dialout connection to this destination is to be active during this time period. If the bit for a time interval equals 0, there is to be no dialout connection to this destination during this time period. This encoding of dialout times means dialout must be specified in 15 minutes intervals. (Depending on the user interface, Workshop may be able to reconstruct the user's input from this bit string. If it can't, it will be necessary to define an object that contains encoding for Workshop -- or change this object so it can be used by both the nX and Workshop.) This field does not apply to leased lines.
INT destHolidaySchedule	1.3.6.1.4.1.1055.2.6.1.1.16	INTEGER	read-write	Default value on nX: 0 NO LONGER USED. This item specifies which day's dialout schedule is to be used for holidays. For example, this allows a person to specify that on holidays to use Sunday's dialout schedule. 'Normal' indicates that the day's standard dialout schedule is to be used. 'Nodialout' indicates that no dialout at all is to occur on holidays.
INT destLinkLayerNRZFlag	1.3.6.1.4.1.1055.2.6.1.1.17	INTEGER	read-write	Default value on nX: nrz On nX: both ram and flash, field trial 1 (may be encoded into Link Layer Type) If appropriate for the Link Line Type, this flag identifies whether the line is nrz or nrzi. (See wan NRZ Flag.)
INT destLinkLayerProtocolType	1.3.6.1.4.1.1055.2.6.1.1.18	INTEGER	read-write	Default value on nX: ppp On nX: both ram and flash, This flag identifies whether the Link Line Type is ppp. Other options are not supported at this time.
INT destLinkDialupFlag	1.3.6.1.4.1.1055.2.6.1.1.19	INTEGER	read-write	Default value on nX: dialup On nX: both ram and flash, field trial 1 (may be encoded into Link Layer Type) If appropriate for the Link Line Type, this flag identifies whether the line is dialup (switched), dedicated, or DTR dial.
INT destPortType	1.3.6.1.4.1.1055.2.6.1.1.20	INTEGER	read-write	Default value on nX: determined by hardware On nX: from 'ram' (actually hardware), field trial 2 This value indicates whether the dest port is PCMCIA, or a D-shell connection - either RS232 or V.35.
INT destLinkLayerType	1.3.6.1.4.1.1055.2.6.1.1.21	INTEGER	read-write	Default value on nX: async On nX: both ram and flash, field trial 1 This object identifies the type of communication link that is used by this destination. Some data link types require further qualification.
OCT destDialoutStatusData	1.3.6.1.4.1.1055.2.6.1.1.22	OCTET STRING	read-only	It has the same format as the event messages: Message # : 2 bytes Date/Time stamping: 4 bytes (integer, msb first) Length: n bytes defining the size of the parameter list that folllows ( 0 is allowed) Message parameters: n bytes, associated with the message #.
INT destDialoutScheduleFlag	1.3.6.1.4.1.1055.2.6.1.1.23	INTEGER	read-write	Default value on nX: disable
STR destDialinUserName	1.3.6.1.4.1.1055.2.6.1.1.24	DisplayString	read-write	This value identifies a User Name for PAP or CHAP dialin to this destination.
STR destDialinPassword	1.3.6.1.4.1.1055.2.6.1.1.25	DisplayString	read-write	This value identifies the user password for PAP or CHAP dialin to this destination.
INT destMaximumDialinConnectTime	1.3.6.1.4.1.1055.2.6.1.1.26	INTEGER	read-write	This object contains, in minutes, the maximum time to leave this connection active for dialin connections. After the time elapses, the nX will automatically hangup the connection, assuming the user has not already manually terminated the connection. A value of zero means there is no time limit.
INT destTSDFlag	1.3.6.1.4.1.1055.2.6.1.1.27	INTEGER	read-write	Default value on nX: non-tsd This entry defines this Destination (Site) to be either a TSD or non-TSD site. If TSD site, then destTSDInactivityTime, destTSDMaxTime, and destPortGroup are meaningful.
INT destTSDInactivityTime	1.3.6.1.4.1.1055.2.6.1.1.28	INTEGER	read-write	This object contains, in minutes, the maximum time. A value of zero means there is no time limit.
INT destTSDMaxDownTime	1.3.6.1.4.1.1055.2.6.1.1.29	INTEGER	read-write	A value of zero means there is no time limit.
INT destTSDPortGroup	1.3.6.1.4.1.1055.2.6.1.1.30	INTEGER	read-write	Default value on nX: 0. This field is used to identify the Wan port # to which this TSD entry is assigned. port group #128 is used as hunt group in TSD for reserving wan link capacity.
INT destManualDialCallback	1.3.6.1.4.1.1055.2.6.1.1.31	INTEGER	read-write	This item indicates whether callback is enabled in Manual Dial mode.
INT destAllowDynamicIPAddr	1.3.6.1.4.1.1055.2.6.1.1.32	INTEGER	read-write	this entry indicates whether the ip address provided by the remote router (through IPCP negotiation), for the use on the local WAN port, is permitted.
INT destISDNChannels	1.3.6.1.4.1.1055.2.6.1.1.33	INTEGER	read-write	This entry indicates the number B channels supported by the ISDN card (configured from the port page).
STR destDialoutPhoneNumber2	1.3.6.1.4.1.1055.2.6.1.1.34	DisplayString	read-write	Default value on nX: empty This item contains the second phone number that is to be used to call the destination using the second ISDN B channel. This string contains just the AT command set characters for the phone number. During dialout, the nX forms the entire dialout string by prefixing this item with the Modem Dial Prefix.
INT destTSDExpectCallback	1.3.6.1.4.1.1055.2.6.1.1.35	INTEGER	read-write	Default value on nX: no Determines whether to expect a callback. If callback is expected, re-dial should delay as specified by syReverseCallbackDelay
INT destMaxEntry	1.3.6.1.4.1.1055.2.6.2	INTEGER	read-only	Max # of entries allowed in Destination table
destScriptTable	1.3.6.1.4.1.1055.2.6.3		not-accessible	Destination script table
destScriptEntry	1.3.6.1.4.1.1055.2.6.3.2		not-accessible	Chat script information for a destination
INT destScriptEntryStatus	1.3.6.1.4.1.1055.2.6.3.2.1	INTEGER	read-write	Indication of whether or not a valid entry.
STR destinationName	1.3.6.1.4.1.1055.2.6.3.2.2	DisplayString	read-only	Same as destName in the Destination Table.
INT destScriptUseFlag	1.3.6.1.4.1.1055.2.6.3.2.3	INTEGER	read-write	This entry indicates whether the script associated with this site should be executed or not.
INT destScriptTimeout	1.3.6.1.4.1.1055.2.6.3.2.4	INTEGER	read-write	This field specifies the total time limit allocated for the execution of the script to completion
STR destScriptName	1.3.6.1.4.1.1055.2.6.3.2.5	DisplayString	read-write	This entry contains the the name of the script.
STR destScript	1.3.6.1.4.1.1055.2.6.3.2.6	DisplayString	read-write	This entry contains the chat script identified by the entry destScriptName.
STR destScriptStartupCmd	1.3.6.1.4.1.1055.2.6.3.2.7	DisplayString	read-write	This entry contains the command used to indicate the service type to the ISP, if required.
user	1.3.6.1.4.1.1055.2.7
INT userMaxEntries	1.3.6.1.4.1.1055.2.7.1	INTEGER	read-only	A value representing the maximum number of user entries in the user table.
userTable	1.3.6.1.4.1.1055.2.7.2		not-accessible	A list of user entries. The number of entries is given by the value of userNumber.
userEntry	1.3.6.1.4.1.1055.2.7.2.1		not-accessible	A user entry containing objects of users.
INT userStatus	1.3.6.1.4.1.1055.2.7.2.1.2	INTEGER	read-write	A value representing the current status of the user entry for the index value, userName.
STR userName	1.3.6.1.4.1.1055.2.7.2.1.3	DisplayString	read-only	An octet string containing user supplied User Name which identifies a dialin user. On dialin, this is used as the login name for PAP or CHAP.
STR userPassword	1.3.6.1.4.1.1055.2.7.2.1.4	DisplayString	read-write	A display string containing user supplied User Password for user identified by userName.
INT userPermissions	1.3.6.1.4.1.1055.2.7.2.1.5	INTEGER	read-write	A value representing the permissions the user identified by userName has, regarding access to the ports. If none(1) is specified, the user can neither dial out nor accept call. If dial-in(2) is specified, the user can dial-in. If dial-out(4) is specified, the user can dial-out. Specify dial-in(2) and dial-out(4) permissions for both dial-in and dial-out privileges.
INT userCallbackType	1.3.6.1.4.1.1055.2.7.2.1.6	INTEGER	read-write	A value specifiying the type of callback to be used when user identified by userName connects. If none(1) is specified, the connection is maintained, and no callback is performed. If fixed(2) is specified, the connection is terminated after the proper authentication of the user is performed. The number stored in userPhoneNo is used to dialback.
STR userPhoneNo	1.3.6.1.4.1.1055.2.7.2.1.7	DisplayString	read-write	A phone number that is to be used for dialback.
INT userDialInMax	1.3.6.1.4.1.1055.2.7.2.1.8	INTEGER	read-write	A value representing the maximum time in minutes for a dialin connection.
IP userIpAddress	1.3.6.1.4.1.1055.2.7.2.1.10	IpAddress	read-write	A value representing the IP Address to be used for the PPP dial-in connection.
manager	1.3.6.1.4.1.1055.2.8
INT mgrTimeoutForMACProtocolResponses	1.3.6.1.4.1.1055.2.8.1	INTEGER	read-write	Default value on nX: 5 On nX: both ram and flash This object specifies the number of seconds Workshop will wait for a response for a message sent to an nX product before assuming that the packet was lost. If this time elapses, Workshop will resend the packet. Normally this time will be very short, but if the nX product and Workshop are separated by slow WAN links, the time will have to be increased. The nX product does not use this value.
INT mgrNumberOfRetriesForMACProtocolResponses	1.3.6.1.4.1.1055.2.8.2	INTEGER	read-write	Default value on nX: 3 On nX: both ram and flash This object specifies the number of times Workshop will retry sending to an nX product a message that timed out before assuming that the packet cannot be sent. If this count is reached, Workshop will stop trying to send the packet and assume that the unit is no longer responding (e.g. the connection has been terminated). The nX product does not use this value.
INT mgrEventPollingInterval	1.3.6.1.4.1.1055.2.8.3	INTEGER	read-write	Default value on nX: 120 On nX: both ram and flash, field trial 2 This object specifies an interval, in seconds, at which Workshop will poll the nX product in order to obtain current data values with which to update displayed screens. The value of this object is most critical when the log file is being written to disk because if the interval is too long the nX product's circular log buffer may not be large enough to hold all events that occur between polls. (Hopefully, the nX will sequence number all log entries so Workshop can determine if some entries have been missed by Workshop.)
holiday	1.3.6.1.4.1.1055.2.9
INT holidayMaxEntries	1.3.6.1.4.1.1055.2.9.1	INTEGER	read-only	A value representing the maximum number of holiday entries in the holiday table.
holidayTable	1.3.6.1.4.1.1055.2.9.2		not-accessible	Holiday table - one copy
holidayEntry	1.3.6.1.4.1.1055.2.9.2.1		not-accessible	The holiday information for one date.
INT holidayStatus	1.3.6.1.4.1.1055.2.9.2.1.1	INTEGER	read-write	Indication of whether or not a valid entry.
STR holidayDate	1.3.6.1.4.1.1055.2.9.2.1.2	DisplayString	read-only	Default value on nX: 0 On nX: both ram and flash, field trial 2 This item specifies a day which is designated as a special dialout day. The nX uses the month and day.
snmp	1.3.6.1.4.1.1055.2.10
snmpCommunityNameTable	1.3.6.1.4.1.1055.2.10.1		not-accessible	Community name table
snmpCommunityNameEntry	1.3.6.1.4.1.1055.2.10.1.1		not-accessible	The community information for this community.
INT snmpCommunityNameStatus	1.3.6.1.4.1.1055.2.10.1.1.1	INTEGER	read-write	Indication of whether or not a valid entry.
STR snmpCommunityName	1.3.6.1.4.1.1055.2.10.1.1.2	DisplayString	read-only	Default value on nX: none On nX: both ram and flash, field trial 1 This item defines a community name to be recognized by the nX Product. For convenience of the user, Workshop will restrict community strings to be ASCII characters.
INT snmpCommunityPermission	1.3.6.1.4.1.1055.2.10.1.1.3	INTEGER	read-write	Default value on nX: Three rows are defined initially, one with each of the above permissions. On nX: both ram and flash This item defines the permission level for its associated Community Name.
snmpMacServerTable	1.3.6.1.4.1.1055.2.10.2		not-accessible	SNMP MAC server table - one copy
snmpMacServerEntry	1.3.6.1.4.1.1055.2.10.2.1		not-accessible	The SNMP MAC server information for one server.
INT snmpMacServerStatus	1.3.6.1.4.1.1055.2.10.2.1.1	INTEGER	read-write	Indication of whether or not a valid entry.
OCT snmpMacServerAddress	1.3.6.1.4.1.1055.2.10.2.1.2	OCTET STRING	read-only	Default value on nX: none On nX: both ram and flash, field trial 1 This item contains the MAC address of the server to which SNMP traps are to be sent. A value of zero indicates no server.
snmpIpServerTable	1.3.6.1.4.1.1055.2.10.3		not-accessible	SNMP IP server table - one copy
snmpIpServerEntry	1.3.6.1.4.1.1055.2.10.3.1		not-accessible	The SNMP IP server information for one server.
INT snmpIpServerStatus	1.3.6.1.4.1.1055.2.10.3.1.1	INTEGER	read-write	Indication of whether or not a valid entry.
IP snmpIpServerAddress	1.3.6.1.4.1.1055.2.10.3.1.2	IpAddress	read-only	Default value on nX: 0 On nX: both ram and flash, field trial 1 This item contains the IP address of the server to which SNMP traps are to be sent. A value of zero indicates no server.
INT snmpCommunityNameMaxEntry	1.3.6.1.4.1.1055.2.10.4	INTEGER	read-only	Max # of entries allowed in snmpCommunityName table
event	1.3.6.1.4.1.1055.2.11
eventTable	1.3.6.1.4.1.1055.2.11.1		not-accessible	Event table - one copy
eventEntry	1.3.6.1.4.1.1055.2.11.1.1		not-accessible	The event information of one event data.
INT eventGroupIndex	1.3.6.1.4.1.1055.2.11.1.1.1	INTEGER	read-only	index into the event log table entry. It is a reference point where the SNMP manager will issue the GET NEXT request to get the next group of events. nX needs to set this value to match the last SEQUENCE # that is returned in the eventData.
OCT eventData	1.3.6.1.4.1.1055.2.11.1.1.2	OCTET STRING	read-only	A group of event log entries. Each entry will be one event with the following format: Sequence #: 2 bytes Message # : 2 bytes Date/Time stamping: 4 bytes (integer, msb first) Length: n bytes defining the size of the parameter list that follows ( 0 is allowed) Message parameters: n bytes, associated with the message #.
discovery	1.3.6.1.4.1.1055.3
STR discNodeName	1.3.6.1.4.1.1055.3.1	DisplayString	read-only	The Node Name consists of the hardware type and MAC address as follows: SoHo-001122334455 for SoHo, Central001122334455 for Central Torte-001122334455 for Torte (not available) Rout-001122334455 for ROUTEMAN (1/2 meg version) RoutXL-001122334455 for ROUTEMANXL (1 meg version).
INT discModel	1.3.6.1.4.1.1055.3.2	INTEGER	read-only	The Model contains a numeric identifier for the hardware model, as follows: 256 - SoHo, 257 - Central, 258 - Torte (not available), 259 - ROUTEMAN, 260 - ROUTEMANXL (1 meg version).
INT discProto	1.3.6.1.4.1.1055.3.3	INTEGER	read-only	The Discover Protocol is the protocol over which the last Get request was received from.
fileMgmt	1.3.6.1.4.1.1055.4
INT syFMOperation	1.3.6.1.4.1.1055.4.1	INTEGER	read-write	This object is used to initiate a file management operation. Operations are as described below. If this object is read, other(1) will be returned.
TIK syFMTimeStamp	1.3.6.1.4.1.1055.4.2	TimeTicks	read-only	This specifies the value of sysUpTime when the most recent file management operation was initiated.
INT syFMError	1.3.6.1.4.1.1055.4.3	INTEGER	read-only	This object identifies the results of the most recent attempt at a file operation. If no file operations have been attempted since the system was initialized, this object will have the value none(1).
syFileTransfer	1.3.6.1.4.1.1055.4.4
INT fileTransferStatus	1.3.6.1.4.1.1055.4.4.1	INTEGER	read-write	This identifies the current status of the file Transfer operation. If there is a transfer in progress, this object will have the value inProgress(2). Otherwise inactive(1) will be returned.
TIK fileTransferStartTime	1.3.6.1.4.1.1055.4.4.2	TimeTicks	read-only	This specifies the value of sysUpTime when the most recent file Transfer operation was initiated.
OCT fileTransferFileLength	1.3.6.1.4.1.1055.4.4.3	OCTET STRING	read-write	This specifies the total Data Length of current file being transferred, in bytes.
INT fileTransferCheckSum	1.3.6.1.4.1.1055.4.4.4	INTEGER	read-write	This specifies the CCITT cyclic redundancy checksum of current file being transffered.
INT fileTransferDirection	1.3.6.1.4.1.1055.4.4.5	INTEGER	read-only	This identifies the current direction of the file Transfer operation. If there is a transfer in progress, this object will have the value copyingFromLX(2), if file is being copied to the Box. Otherwise it will have copyingToLX(1). If no transfer in progress none will be returned.
TIK fileTransferLastRcvTime	1.3.6.1.4.1.1055.4.4.6	TimeTicks	read-only	This specifies the value of sysUpTime when the most recent file Object was received. This value is used to time out the File Transfer operation if no File Object is received within a timeout period.
MAC fileTransferRemoteAddr	1.3.6.1.4.1.1055.4.4.7	MacAddress	read-only	This object specifies the MAC Address of the Remote management stations which initiated the file transfer.
OCT fileTransferRemoteFileName	1.3.6.1.4.1.1055.4.4.8	OCTET STRING	read-write	This specifies the path and name of a Remote file residing on the remote management station. sbeFileTransferRemoteAddr For LAN Boot this item MUST be 12 characters in length!
STR fileTransferLocalFileName	1.3.6.1.4.1.1055.4.4.9	DisplayString	read-write	This specifies the name of Local File being transferred. For the File Transfer TO the remote station this becomes the name of the source file. For the FROM operation this is the name of the local file where the new file will be stored. For LAN Boot this item MUST be 12 characters in length!
OCT fileTransferData	1.3.6.1.4.1.1055.4.4.10	OCTET STRING	read-write	This field contains the data of the file being transfered. The data has a header inside which contains information about the file being transfered and the current data block.
syFileInfo	1.3.6.1.4.1.1055.4.5
OCT syFileInfoVersion	1.3.6.1.4.1.1055.4.5.1	OCTET STRING	read-only	The version string from a module header. Example, $Release: 2.0.4a $File: lxkernel.gz $Type: kernelFile $DateTime: 07/09/96 19:11 $ProductType: SoHo $Lic: (C)1996 SBE,Inc $Release: is a three part number X.Y.Z, e.g. 2.0.4a $File: is up to 8.3 character file name, e.g. lxkernel.gz $Type: is kernelFile or moduleFile $DateTime: is Month/DayNumber/Year TimeOfDay $ProductType: is the hardware, e.g. SoHo, Central, Routeman, RoutXL $Lic: is (C) Year(s) SBE,Inc Sound files and internal configuration files have null syFileInfoVersion strings.
OCT syFileInfoChecksum	1.3.6.1.4.1.1055.4.5.2	OCTET STRING	read-only	This MIB entry is used to retrieve the Information related to a file on the nX File System. The File information contains version string, checksum and length of the file. Information in this field is mapped in to the file information structure by the nX and Workshop.
OCT syFileInfoLength	1.3.6.1.4.1.1055.4.5.3	OCTET STRING	read-only	This MIB entry is used to retrieve the Information related to a file on the nX File System. The File information contains version string, checksum and length of the file. Information in this field is mapped in to the file information structure by the nX and Workshop.
syDirTable	1.3.6.1.4.1.1055.4.6		not-accessible	The directory entry of one file.
syDirEntry	1.3.6.1.4.1.1055.4.6.1		not-accessible
INT syDirStatus	1.3.6.1.4.1.1055.4.6.1.1	INTEGER	read-only
OCT syDirName	1.3.6.1.4.1.1055.4.6.1.2	OCTET STRING	read-only
INT syDirCompressSize	1.3.6.1.4.1.1055.4.6.1.3	INTEGER	read-only
OCT syDirVersion	1.3.6.1.4.1.1055.4.6.1.4	OCTET STRING	read-only
INT syDirUncompressSize	1.3.6.1.4.1.1055.4.6.1.5	INTEGER	read-only
OCT fileName	1.3.6.1.4.1.1055.4.7	OCTET STRING	read-write	This field contains a null terminated string in the format of nnnnnnnn.xxx (DOS format file name). The file name is used by the delete file operation, or the get file info operation.
OCT fileNameFrom	1.3.6.1.4.1.1055.4.8	OCTET STRING	read-write	This field contains a null terminated string in the format of nnnnnnnn.xxx (DOS format file name). The file name is the old file name used by the rename file operation.
OCT fileNameTo	1.3.6.1.4.1.1055.4.9	OCTET STRING	read-write	This field contains a null terminated string in the format of nnnnnnnn.xxx (DOS format file name). The file name is the new file name used by the rename file operation.
modempool	1.3.6.1.4.1.1055.6
INT modempoolEnabled	1.3.6.1.4.1.1055.6.1	INTEGER	read-write	Default value on nX: disabled On nX: both ram and flash, field trial 1 If this value is 'enabled', the modem pool is enabled. If this value is 'disabled', if the modem pool is disabled.
STR modempoolNodeName	1.3.6.1.4.1.1055.6.2	DisplayString	read-write	The nodename contains the modem server name advertised in SAP and UDP broadcasts
INT modempoolProtoSupport	1.3.6.1.4.1.1055.6.3	INTEGER	read-write	Default value on nX: 0 On nX: both ram and flash, This item is a bit encoded value representing various protocols to be used for server advertisement. The encoded values are: IP(1), IPX(2). Any combination of these values is valid. Zero is invalid
endOfSBEMib	1.3.6.1.4.1.1055.65535
INT dummyStopperForWorkshopForGetNext	1.3.6.1.4.1.1055.65535.1	INTEGER	read-only

RFC description

SBE (Standard Business Equipment) system management MIB defining objects for device configuration and operational status.

Start monitoring SBE-series network router/appliance (system identity/boot state/license activation level) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SBE-MIB

What Is SBE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description