DL-NEW-DSX1-MIB

All MIBs › DL-NEW-DSX1-MIB

Category: Domain: WAN

Description: DSX1 interface MIB for DL devices providing T1/E1 line management, performance monitoring, and alarm objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DL-NEW-DSX1-MIB?

This is a Digital Link (DL) enterprise MIB providing management for DSX1 (T1/E1) digital circuit interfaces on Digital Link WAN access devices. It exposes hardware configuration, operational status, and archived unit-configuration data related to T1/E1 line units. Its monitoring focus is hardware status of the WAN interface card: tracking the unit's hardware configuration, current operational/alarm status, and stored configuration archives, which helps detect line faults, misconfigurations, or hardware failures on the T1/E1 circuit. It likely complements standard IETF DS1/E1 MIBs (such as RFC 1406/2495-style DS1-MIB) that define the underlying line-performance counters this vendor module extends. It is typically deployed in telecom or enterprise WAN environments using Digital Link T1/E1 access equipment for leased-line connectivity. Engineers can download the DL-NEW-DSX1-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DL-NEW-DSX1-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Digital Link DSX1 (T1/E1) WAN access unit

Monitoring Examples

An administrator can poll dlcUnitStatus to check the current alarm/operational condition of the DSX1 unit, revealing conditions such as loss of signal or frame alignment on the T1/E1 line. dlcUnitHwConfig and dlcUnitConfig can be compared against dlcUnitUserArchive to detect drift between the currently applied configuration and the last saved/archived configuration, a useful check after a line card replacement or firmware update.

What Can Be Monitored

unit operational/alarm status
hardware configuration
current vs. archived configuration

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
digital_link	1.3.6.1.4.1.300
dl_new_t1	1.3.6.1.4.1.300.200
NTF startTest	1.3.6.1.4.1.300.200.0.1			Sent upon the initiation of a new test condition.
NTF endTest	1.3.6.1.4.1.300.200.0.2			Sent upon the termination of a test condition.
NTF startAlarm	1.3.6.1.4.1.300.200.0.3			Indicates the beginning of a new alarm condition.
NTF endAlarm	1.3.6.1.4.1.300.200.0.4			Indicates the end of an alarm condition.
NTF manualConfigChange	1.3.6.1.4.1.300.200.0.5			Generated when the configuration was changed manually on the unit.
dlcUnitHwConfig	1.3.6.1.4.1.300.200.1
INT dlcUnitModelType	1.3.6.1.4.1.300.200.1.1	INTEGER	read-only	The unit model type.
STR dlcUnitHwRev	1.3.6.1.4.1.300.200.1.2	DisplayString	read-only	The ASCII code of the hardware revision number.
INT dlcUnitHwOptions	1.3.6.1.4.1.300.200.1.3	INTEGER	read-only	A bit map, reported as the sum of all the values that correspond to installed options: realTimeClock ( 1) netPortT1 ( 2) netPortE1 ( 4) auxPortT1 ( 8) auxPortE1 ( 16) otherNetT1 ( 32) otherNetE1 ( 64) reserved1 (128) reserved2 (256) reserved3 (512) `netPortT1' and `netPortE1' are mutually exclusive and one of the two will always be TRUE. `auxPortT1' and `auxPortE1' are mutually exclusive; if both are FALSE, there is no AUX port present. `otherNetT1' and `otherNetE1' are mutually exclusive; if both are FALSE, there is no CSU port present.
STR dlcUnitSwRev	1.3.6.1.4.1.300.200.1.4	DisplayString	read-only	The ASCII code of the software revision number.
INT dlcUnitDataPorts	1.3.6.1.4.1.300.200.1.5	INTEGER	read-only	The number of data ports installed on the unit.
INT dlcUnitRam	1.3.6.1.4.1.300.200.1.6	INTEGER	read-only	The amount of usable ram in the unit, in KBytes.
INT dlcUnitRom	1.3.6.1.4.1.300.200.1.7	INTEGER	read-only	The amount of usable rom in the unit, in KBytes.
INT dlcUnitFlash	1.3.6.1.4.1.300.200.1.8	INTEGER	read-only	The amount of FLASH ROM in the unit, in KBytes. If dlcUnitFlash is 0, the Downloadable Code option is not installed.
INT dlcUnitSlotNum	1.3.6.1.4.1.300.200.1.9	INTEGER	read-only	The slot number the unit is in. If it's a stand alone unit, this object will return 0.
STR dlcUnitMibRev	1.3.6.1.4.1.300.200.1.10	DisplayString	read-only	The ASCII code of the MIB revision number.
INT dlcUnitFeatures	1.3.6.1.4.1.300.200.1.11	INTEGER	read-only	Feature configuration for Solo Select. The value returned is a bit mask of which feature key is on/capable when the corresponding bit is 1.
dlcUnitConfig	1.3.6.1.4.1.300.200.2
STR dlcUnitId	1.3.6.1.4.1.300.200.2.1	DisplayString	read-write	A name that uniquely and globally identifies the unit. The Unit ID must consist of (upper-case) letters 'A'..'Z' and digits '0'..'9'. The first character of the Unit ID may not be a digit.
BOO dlcUnitProtectMode	1.3.6.1.4.1.300.200.2.2	Boolean	read-write	When true, the unit configuration can not be changed from the front panel nor can tests be initiated or terminated from the front panel.
BOO dlcUnitYellowEnable	1.3.6.1.4.1.300.200.2.3	Boolean	read-write	When false, yellow alarm conditions are ignored when received from a Dsx1 port, and the unit will never transmit a Yellow Alarm signal on a Dsx1 port. This applies to all ports: mainNet, aux, otherNet.
POR dlcUnitNetPassFdl	1.3.6.1.4.1.300.200.2.4	PortId	read-write	Indicates which Dsx1 DTE port's FDL is connected to the `mainNet' FDL when this unit has no traffic of its own. Meaninigful values are `aux', `otherNet', and `noPort'.
POR dlcUnitMainClockSource	1.3.6.1.4.1.300.200.2.5	PortId	read-write	This is the primary transmit timing source.
POR dlcUnitAltClockSource	1.3.6.1.4.1.300.200.2.6	PortId	read-write	This is the alternate transmit timing source. It is used when the primary source is not available.
INT dlcUnitExtClockRate	1.3.6.1.4.1.300.200.2.7	INTEGER	read-write	The signal arriving at the BNC connector on the back of the unit, in units of KHz. Must be a multiple of 56 or 64 KHz (n56 or n64) or 1544. For T1 units, the largest acceptable value is 1544. For E1 units, the value can go up to 2048. For Solo CSU products, the value is fixed at 1544 and cannot be changed.
LOO dlcUnitFullBandwidthLoopCode	1.3.6.1.4.1.300.200.2.8	LoopCodeType	read-write	Determines the loop codes we transmit for the Full Bandwidth Loop Up Remote and Loop Down Remote tests and the code we respond to when it's received on the NET port. For the fullBandwidthLoopCode, `v54' is an invalid value.
LOO dlcUnitFractionalLoopCode	1.3.6.1.4.1.300.200.2.9	LoopCodeType	read-write	Determines the loop codes we transmit for the Fractional Loop Up Remote and Loop Down Remote tests and the code we respond to when it's received on fractional bandwidth.
INT dlcUnitTestLength	1.3.6.1.4.1.300.200.2.10	INTEGER	read-write	Determines the time interval after which tests are automatically terminated. Valid values are 0, 1, 15 and 60. 0 stands for unlimited, 1 for 1 minute, 15 for 15 minutes and 60 for 60 minutes.
STR dlcUnitUserPattern1	1.3.6.1.4.1.300.200.2.11	DisplayString	read-write	This is a sequence of the characters '0' and '1' that represents the first of two user patterns. The first character represents the first bit in the sequence.
STR dlcUnitUserPattern2	1.3.6.1.4.1.300.200.2.12	DisplayString	read-write	This is a sequence of the characters '0' and '1' that represents the second of two user patterns. The first character represents the first bit in the sequence.
BOO dlcUnitBlockAllAlarms	1.3.6.1.4.1.300.200.2.13	Boolean	read-write	When dlcUnitBlockAllAlarms is TRUE, the unit will never send any traps.
dlcUnitDsx1TrapEnableTable	1.3.6.1.4.1.300.200.2.14		not-accessible	A list of traps that are related to a Dsx1 port.
dlcDsx1TrapEnableEntry	1.3.6.1.4.1.300.200.2.14.1		not-accessible	An entry in the Dsx1 Trap Enable table.
POR dlcDsx1TrapPortId	1.3.6.1.4.1.300.200.2.14.1.1	PortId	read-only	Uniquely identifies this port. Valid values are `mainNet', `aux', `otherNet'.
INT dlcDsx1BpvThresholdTrap	1.3.6.1.4.1.300.200.2.14.1.2	INTEGER	read-write	Defines Bipolar Violation Error Rate threshold in units of BPV errors per minute. When this threshold is exceeded, the unit will send a trap to the SNMP manager. The threshold is of the form M x 10 ^ -E where M is a mantissa and E the exponent. Both are single digit values. M and E are represented in this value as one number: (M) x 10 + (E). For example, the threshold 7x10^-3 BPVs/min is encoded as the integer 73. A value of 0 disables the trap altogether. Valid values for dlcDsx1BpvThresholdTrap are: 13 23 33 43 53 63 14 24 34 44 54 64 74 84 94 15 25 35 45 55 65 75 85 95 16 26 36 46 56 66 76 86 96 17 27 37 47 57 67 77 87 97 28 38 48 58 68 78 88 98 or, from 6E-3 to 2E-8. N.B. The BPV Threshold Alarm exists only for the mainNet and otherNet Port IDs, so setting the Threshold for the aux PortId will always fail. The BPV Threshold is always reported as 0 for the aux PortId.
INT dlcDsx1OofThresholdTrap	1.3.6.1.4.1.300.200.2.14.1.3	INTEGER	read-write	Defines the Out Of Frame Error Rate threshold in units of OOF errors per minute. The threshold is encoded the same as dlcDsx1BpvThresholdTrap. A value of 0 disables the trap altogether. Valid values for dlcDsx1OofThresholdTap are: 12 22 22 42 52 62 72 13 23 33 43 53 63 73 83 93 14 24 34 44 54 64 74 84 94 15 25 35 45 55 65 75 85 95 36 46 56 66 76 86 96 or, from 7E-2 to 3E-6. N.B. The OOF Threshold Alarm exists only for the mainNet and otherNet Port IDs, so setting the Threshold for the aux PortId will always fail. The OOF Threshold is always reported as 0 for the aux PortId.
INT dlcDsx1CrcThresholdTrap	1.3.6.1.4.1.300.200.2.14.1.4	INTEGER	read-write	Defines the CRC-6 Error Rate threshold in units of CRC errors per minute. The threshold is encoded the same as dlcDsx1BpvThresholdTrap. A value of 0 disables the trap altogether. Valid values for dlcDsx1CrcThresholdTrap are: 10 11 21 31 41 51 61 71 81 91 12 22 32 42 52 62 72 82 92 13 23 33 43 53 63 73 83 93 14 24 34 44 54 64 74 84 94 55 65 75 85 95 or, from 1E0 to 5E-5. N.B. The CRC Threshold Alarm exists only for the mainNet and otherNet Port IDs, so setting the Threshold for the aux PortId will always fail. The CRC Threshold is always reported as 0 for the aux PortId.
BOO dlcDsx1LossOfSignalTrapEnable	1.3.6.1.4.1.300.200.2.14.1.5	Boolean	read-write	Enables or disables a trap upon loss of network signal (LOS) on a Dsx1 port.
BOO dlcDsx1LossOfSyncTrapEnable	1.3.6.1.4.1.300.200.2.14.1.6	Boolean	read-write	Enables or disables a trap upon loss of network framing (LOF) on a Dsx1 port.
BOO dlcDsx1ReceiveAIStrapEnable	1.3.6.1.4.1.300.200.2.14.1.7	Boolean	read-write	Enables or disables a trap upon detection of AIS (Blue Alarm Signal) on a Dsx1 port.
BOO dlcDsx1ReceiveYellowAlarmTrapEnable	1.3.6.1.4.1.300.200.2.14.1.8	Boolean	read-write	Enables or disables a trap upon detection of Yellow Alarm Signal on a Dsx1 port.
BOO dlcDsx1ReceiveRemoteAlarmTrapEnable	1.3.6.1.4.1.300.200.2.14.1.9	Boolean	read-write	Enables or disables a trap upon detection of Remote Alarm Indicator on an E1 Dsx1 port. For T1 units, this object's value will always be read as 0 and set operations will succeed, but the value will not be changed.
BOO dlcDsx1PSfailureTrapEnable	1.3.6.1.4.1.300.200.2.14.1.10	Boolean	read-write	Enables or disables a trap upon a power supply failure. This object doesn't really belong in the dlcDsx1TrapEnableTable. It is specific to units that are installed in a shelf. When accessing this object, the index (portId) is ignored.
BOO dlcDsx1CntlCrdMissingTrapEnable	1.3.6.1.4.1.300.200.2.14.1.11	Boolean	read-write	Enables or disables a trap upon detection of a missing controller card. This object doesn't really belong in the dlcDsx1TrapEnableTable. It is specific to units that are installed in a shelf. When accessing this object, the index (portId) is ignored.
BOO dlcDsx1FdlLinkTrapEnable	1.3.6.1.4.1.300.200.2.14.1.12	Boolean	read-write	Enables or disables a trap upon detection of the remote unit is not responding to DLC FDL messages.
INT dlcDsx1IbCrcThresholdTrap	1.3.6.1.4.1.300.200.2.14.1.13	INTEGER	read-write	Defines the In-Band CRC Error Rate threshold in units of CRC errors per minute. The threshold is encoded the same as dlcDsx1BpvThresholdTrap. A value of 0 disables the trap altogether. For the Eclipse, valid values of dlcDsx1IbCrcThresholdTrap range from 47 to 91. N.B. The CRC Threshold Alarm exists only for the mainNet port.
BOO dlcDsx1InbandLinkTrapEnable	1.3.6.1.4.1.300.200.2.14.1.14	Boolean	read-write	Enables or disables a trap upon detection of the inband link.
dlcUnitDataDteLossTrapEnableTable	1.3.6.1.4.1.300.200.2.15		not-accessible	Enables or disables a trap upon the loss of signal on a Data DTE port.
dlcDataDteLossTrapEnableEntry	1.3.6.1.4.1.300.200.2.15.1		not-accessible	An entry in the Data DTE Loss Trap Enable table.
POR dlcDataLossPortId	1.3.6.1.4.1.300.200.2.15.1.1	PortId	read-only	Uniquely identifies this port. Valid values are `data1' through `data32'.
BOO dlcDataLossEnable	1.3.6.1.4.1.300.200.2.15.1.2	Boolean	read-write	Says whether to enable this trap.
BOO dlcUnitExternalAlarmInputTrapEnable	1.3.6.1.4.1.300.200.2.16	Boolean	read-write	Enables or disables a trap upon detection of an alarm condition on the External Alarm Input.
INT dlcUnitExternalAlarmInputContacts	1.3.6.1.4.1.300.200.2.17	INTEGER	read-write	When set to normallyOpen, an alarm is declared when the contacts close ... and vice-versa.
STR dlcUnitExternalAlarmInputMessage	1.3.6.1.4.1.300.200.2.18	DisplayString	read-write	A character string that describes what's going on when an alarm on the External Alarm Input is detected.
INT dlcUnitExternalAlarmOutputContacts	1.3.6.1.4.1.300.200.2.19	INTEGER	read-write	When set to normallyOpen, the contacts close when any enabled alarm occurs and vice-versa. Pushing any button on the units Front Panel will cause the alarm contacts to open again until another alarm is recognized.
BOO dlcUnitExternalAlarmOutputTrapEnable	1.3.6.1.4.1.300.200.2.20	Boolean	read-write	Enables or disables the external alarm output contacts.
dlcUnitDsx1ConfigTable	1.3.6.1.4.1.300.200.2.21		not-accessible	A table of configuration items for a Dsx1 port.
dlcDsx1ConfigEntry	1.3.6.1.4.1.300.200.2.21.1		not-accessible	An entry in the Dsx1 configuration table.
POR dlcDsx1ConfigPortId	1.3.6.1.4.1.300.200.2.21.1.1	PortId	read-only	Uniquely identifies this port. Valid values are `mainNet', `aux', `otherNet'.
INT dlcDsx1Framing	1.3.6.1.4.1.300.200.2.21.1.2	INTEGER	read-write	Dsx1 framing type: T1 --> D4 or ESF; E1 --> CRC4 or not. Unstructured is E1 only, when in this mode, the E1 line acts like a 2048 Bps pipe with no framing information.
INT dlcDsx1LineCode	1.3.6.1.4.1.300.200.2.21.1.3	INTEGER	read-write	Dsx1 line code type, AMI or B8ZS. E1 lines are always HDB3.
INT dlcDsx1LineMatching	1.3.6.1.4.1.300.200.2.21.1.4	INTEGER	read-write	Dsx1 line build out or equalization: For a T1 NET port, LBO is 0, -7.5 or -15dB. For a T1 AUX port, EQ is 0..533 feet. For any E1 port, impedance is 75 or 120 Ohms.
BOO dlcDsx1DacsMode	1.3.6.1.4.1.300.200.2.21.1.5	Boolean	read-write	True if DACS mode is in effect for this port.
BOO dlcDsx1UseDlcFdlProtocol	1.3.6.1.4.1.300.200.2.21.1.6	Boolean	read-write	True when DLC FDL protocol is enabled over this port's FDL.
BOO dlcDsx1UseAnsiProtocol	1.3.6.1.4.1.300.200.2.21.1.7	Boolean	read-write	True if ANSI Dsx1.403 is enabled over the FDL.
BOO dlcDsx1Bit7Stuffing	1.3.6.1.4.1.300.200.2.21.1.8	Boolean	read-write	When true, bit 7 stuffing is turned on for a T1 Aux port to provide pulse density protection. Valid only on a T1 AUX port.
INT dlcDsx1InBandBit	1.3.6.1.4.1.300.200.2.21.1.9	INTEGER	read-write	Specifies which bit in Timeslot 1 of an E1 link is used to pass message traffic. Not implemented for T1 ports.
dlcUnitDataDteConfigTable	1.3.6.1.4.1.300.200.2.22		not-accessible	The data DTE configuration table.
dlcDataDteConfigEntry	1.3.6.1.4.1.300.200.2.22.1		not-accessible	An entry in the data DTE configuration table.
POR dlcDataConfigPortId	1.3.6.1.4.1.300.200.2.22.1.1	PortId	read-only	Uniquely identifies this port. Valid values are `data1' through `data32'.
INT dlcDataConfigEncoding	1.3.6.1.4.1.300.200.2.22.1.2	INTEGER	read-write	Data DTE encoding type.
INT dlcDataConfigLoss	1.3.6.1.4.1.300.200.2.22.1.3	INTEGER	read-write	The criterion to declare a Loss of Data DTE.
INT dlcDataConfigMode	1.3.6.1.4.1.300.200.2.22.1.4	INTEGER	read-write	In dteMode the unit is the DTE and the external equipment the DCE.
INT dlcDataConfigFormat	1.3.6.1.4.1.300.200.2.22.1.5	INTEGER	read-write	Selects V.35 or RS449 format.
INT dlcDataConfigTransmitTiming	1.3.6.1.4.1.300.200.2.22.1.6	INTEGER	read-write	Selects the Data DTE tramsmit timing source. Can be SCTE, SCT or inverted SCT.
dlcUnitMuxConfigTable	1.3.6.1.4.1.300.200.2.23		not-accessible	This is the timeslot map configuration.
dlcMuxConfigEntry	1.3.6.1.4.1.300.200.2.23.1		not-accessible	An entry in the timeslot map.
INT dlcMuxConfigBusId	1.3.6.1.4.1.300.200.2.23.1.1	INTEGER	read-only	Identifies which muxBus this timeslot is on.
INT dlcMuxConfigSlotNumber	1.3.6.1.4.1.300.200.2.23.1.2	INTEGER	read-only	Uniquely identifies this timeslot.
POR dlcMuxConfigPortId	1.3.6.1.4.1.300.200.2.23.1.3	PortId	read-write	Says which DTE port receives data from the indicated muxBus during this timeslot.
dlcUnitSnmpConfig	1.3.6.1.4.1.300.200.2.24
IP dlcSnmpUnitIpAddr	1.3.6.1.4.1.300.200.2.24.1	IpAddress	read-write	Specifies the IP address that is assigned to this unit.
IP dlcSnmpUnitNetMask	1.3.6.1.4.1.300.200.2.24.2	IpAddress	read-write	Specifies the net mask that this unit uses.
IP dlcSnmpTrapAddr1	1.3.6.1.4.1.300.200.2.24.3	IpAddress	read-write	Specifies the IP address of the management station to which this unit sends traps.
IP dlcSnmpTrapAddr2	1.3.6.1.4.1.300.200.2.24.4	IpAddress	read-write	Specifies the IP address of the management station to which this unit sends traps.
IP dlcSnmpTrapAddr3	1.3.6.1.4.1.300.200.2.24.5	IpAddress	read-write	Specifies the IP address of the management station to which this unit sends traps.
GAU dlcSnmpTrapDlci1	1.3.6.1.4.1.300.200.2.24.6	Gauge	read-write	Specifies the first of three DLCI value to which this unit sends TRAP PDUs.
GAU dlcSnmpTrapDlci2	1.3.6.1.4.1.300.200.2.24.7	Gauge	read-write	Specifies the second of three DLCI value to which this unit sends TRAP PDUs.
GAU dlcSnmpTrapDlci3	1.3.6.1.4.1.300.200.2.24.8	Gauge	read-write	Specifies the third of three DLCI value to which this unit sends TRAP PDUs.
INT dlcSnmpTrapDirection1	1.3.6.1.4.1.300.200.2.24.9	INTEGER	read-write	Specifies the first of three Port to which this unit sends TRAP PDUs.
INT dlcSnmpTrapDirection2	1.3.6.1.4.1.300.200.2.24.10	INTEGER	read-write	Specifies the second of three Port to which this unit sends TRAP PDUs.
INT dlcSnmpTrapDirection3	1.3.6.1.4.1.300.200.2.24.11	INTEGER	read-write	Specifies the third of three Port to which this unit sends TRAP PDUs.
INT dlcSnmpTrapDirection	1.3.6.1.4.1.300.200.2.24.12	INTEGER	read-write	Specifies where this unit sends TRAP PDUs.
dlcSnmpEthernetConfiguration	1.3.6.1.4.1.300.200.2.24.13
IP dlcEthernetIpAddr	1.3.6.1.4.1.300.200.2.24.13.1	IpAddress	read-write	Specifies the IP address of Ethernet port.
IP dlcEthernetIpMask	1.3.6.1.4.1.300.200.2.24.13.2	IpAddress	read-write	Specifies the subnet mask of Ethernet port.
IP dlcEthernetGatewayAddr	1.3.6.1.4.1.300.200.2.24.13.3	IpAddress	read-write	Specifies the gateway address of Ethernet port.
MAC dlcEthernetMacAddr	1.3.6.1.4.1.300.200.2.24.13.4	MacAddress	read-only	The MAC address of the Ethernet port.
dlcUnitConfigTime	1.3.6.1.4.1.300.200.2.25
INT dlcUnitTimeYear	1.3.6.1.4.1.300.200.2.25.1	INTEGER	read-write	The unit's notion of the current year.
INT dlcUnitTimeMonth	1.3.6.1.4.1.300.200.2.25.2	INTEGER	read-write	The unit's notion of the current month.
INT dlcUnitTimeDay	1.3.6.1.4.1.300.200.2.25.3	INTEGER	read-write	The unit's notion of the current day.
INT dlcUnitTimeHour	1.3.6.1.4.1.300.200.2.25.4	INTEGER	read-write	The the unit's notion of the current hour.
INT dlcUnitTimeMinute	1.3.6.1.4.1.300.200.2.25.5	INTEGER	read-write	The the unit's notion of the current minute.
INT dlcUnitTimeSecond	1.3.6.1.4.1.300.200.2.25.6	INTEGER	read-write	The the unit's notion of the current second.
STR dlcUnitSerialNum	1.3.6.1.4.1.300.200.2.26	DisplayString	read-only	An ID that uniquely and globally identifies the unit. A Serial Number must consist of printable ASCII characters 0x20 ..0x7E.
dlcUnitModemConfig	1.3.6.1.4.1.300.200.2.27
STR dlcModemPhoneNum1	1.3.6.1.4.1.300.200.2.27.1	DisplayString	read-write	The first phone number to dial when the unit needs to set up a modem connection.
STR dlcModemPhoneNum2	1.3.6.1.4.1.300.200.2.27.2	DisplayString	read-write	The second phone number to try if the phone number failed in setting up a modem connection.
STR dlcModemInitString1	1.3.6.1.4.1.300.200.2.27.3	DisplayString	read-write	In setting up a modem connection, the first group of commands used to initialize the modem.
STR dlcModemInitString2	1.3.6.1.4.1.300.200.2.27.4	DisplayString	read-write	In setting up a modem connection, the second group of commands used to initialize the modem. There is a delay between sending the first and second groups of initialzation commands.
INT dlcUnitInbandMode	1.3.6.1.4.1.300.200.2.28	INTEGER	read-only	The type of traffic expected on the link for inband management and IPM.
INT dlcUnitDialOutTimeInterval	1.3.6.1.4.1.300.200.2.29	INTEGER	read-write	A time interval for the dialout. The value should be between 0 and 255.
FRA dlcAlarmSignal	1.3.6.1.4.1.300.200.2.30	FramedUnframed	read-write	Framed/unframed aux alarm signal option
INT dlcUnitIdleCode	1.3.6.1.4.1.300.200.2.31	INTEGER	read-write	Idle Code that is send on unassigned time slots
REM dlcRemoteCommunicationsMode	1.3.6.1.4.1.300.200.2.32	RemoteCommunicationsMode	read-write	Framed/unframed aux alarm signal option
dlcUnitConfigLinkTest	1.3.6.1.4.1.300.200.2.33
INT dlcLinkTestState	1.3.6.1.4.1.300.200.2.33.1	INTEGER	read-write	Specifies the status configuration of link based test. Only setable to values disabled(1) and enabled(2) to end and start the test respectively. Values running(3) and idle(4) are returned for status of the test.
IP dlcLinkTestAddress	1.3.6.1.4.1.300.200.2.33.2	IpAddress	read-write	Specifies the address for the next link based test to run.
INT dlcLinkTestDlci	1.3.6.1.4.1.300.200.2.33.3	INTEGER	read-write	Specifies the frame relay DLCI for the next link based test to run. This value is used when the unit is in frameRelay InbandMode only and if the next link based test is not done on the commPort.
INT dlcLinkTestPort	1.3.6.1.4.1.300.200.2.33.4	INTEGER	read-write	Specifies which port to run the next link based test.
INT dlcLinkTestLength	1.3.6.1.4.1.300.200.2.33.5	INTEGER	read-write	Specifies the time length of the next test to run in minutes.
INT dlcLinkTestInterval	1.3.6.1.4.1.300.200.2.33.6	INTEGER	read-write	Specifies the repetition interval in seconds between packets for the next link based test.
INT dlcLinkTestPacketSize	1.3.6.1.4.1.300.200.2.33.7	INTEGER	read-write	Specifies the packet size for the next link based test.
INT dlcLinkTestPattern	1.3.6.1.4.1.300.200.2.33.8	INTEGER	read-write	Specifies the test pattern for the next link based test.
BOO dlcUnitInbandConfig	1.3.6.1.4.1.300.200.2.34	Boolean	read-only	When true (== 2), inband management is enabled.
INT dlcUnitInbandTrafficType	1.3.6.1.4.1.300.200.2.35	INTEGER	read-only	The type of traffic expected on the link for inband management and IPM.
BOO dlcUnitPerformanceMonitoring	1.3.6.1.4.1.300.200.2.36	Boolean	read-write	When true (== 2), the integrated performance monitoring (IPM) is enabled
BOO dlcUnitPvcAutoDiscovery	1.3.6.1.4.1.300.200.2.37	Boolean	read-write	When true (== 2), automatic discovery of DLCIs is enabled
dlcUnitDelayMonitorConfig	1.3.6.1.4.1.300.200.2.38
dlcDelayMonitorConfigTable	1.3.6.1.4.1.300.200.2.38.1		not-accessible	Table of Delay Monitor test configuration.
dlcDelayMonitorConfigEntry	1.3.6.1.4.1.300.200.2.38.1.1		not-accessible	An entry in the network configuration table.
INT dlcDelayMonitorConfigIndex	1.3.6.1.4.1.300.200.2.38.1.1.1	INTEGER	read-only	Uniquely identifies which delay monitor test in the configuration table.
INT dlcDelayMonitorState	1.3.6.1.4.1.300.200.2.38.1.1.2	INTEGER	read-write	Specifies the status configuration of this delay monitor. Only setable to values disabled(1) and enabled(2) to end and start the test respectively. Values running(3) and idle(4) are returned for status of the test.
IP dlcDelayMonitorTargetAddress	1.3.6.1.4.1.300.200.2.38.1.1.3	IpAddress	read-write	Specifies the address for the next delay monitor to run.
INT dlcDelayMonitorDlci	1.3.6.1.4.1.300.200.2.38.1.1.4	INTEGER	read-write	Specifies the frame relay DLCI for the next delay monitor to run. This value is used when the unit is in frameRelay InbandMode only and if the next delay monitor is not done on the commPort.
INT dlcDelayMonitorPort	1.3.6.1.4.1.300.200.2.38.1.1.5	INTEGER	read-write	Specifies which port to run the next delay monitor.
INT dlcDelayMonitorInterval	1.3.6.1.4.1.300.200.2.38.1.1.6	INTEGER	read-write	Specifies the repetition interval in seconds between packets for the next delay monitor to run.
INT dlcDelayMonitorPacketSize	1.3.6.1.4.1.300.200.2.38.1.1.7	INTEGER	read-write	Specifies the packet size for the next delay monitor.
INT dlcDelayMonitorPattern	1.3.6.1.4.1.300.200.2.38.1.1.8	INTEGER	read-write	Specifies the test pattern for the next delay monitor.
dlcDLCItable	1.3.6.1.4.1.300.200.2.39		not-accessible	Table for current DLCI
dlcDLCItableEntry	1.3.6.1.4.1.300.200.2.39.1		not-accessible	An entry for a DLCI
INT dlcDLCInumber	1.3.6.1.4.1.300.200.2.39.1.1	INTEGER	read-only	Identifies DLCI number.
INT dlcDTECIR	1.3.6.1.4.1.300.200.2.39.1.2	INTEGER	read-only	This DLCI's DTE Confirmed Information Rate (CIR)
INT dlcNETCIR	1.3.6.1.4.1.300.200.2.39.1.3	INTEGER	read-only	This DLCI's NET Confirmed Information Rate (CIR)
INT dlcDLCIstatus	1.3.6.1.4.1.300.200.2.39.1.4	INTEGER	read-write	This object represents status of the entry. When read, it will return status 'active' or 'inactive' representing the status of the row. When written, this object is used to add or delete entry. Setting to 'enabled' will add a new entry, setting to 'disabled' will delete the entry.
dlcLMIConditioningGroup	1.3.6.1.4.1.300.200.2.41
dlcLMIConfiguration	1.3.6.1.4.1.300.200.2.41.1
INT dlcLMIEnable	1.3.6.1.4.1.300.200.2.41.1.1	INTEGER	read-write	This object specifies whether to enable or disable LMI Conditioning.
INT dlcMaintenanceDLCI	1.3.6.1.4.1.300.200.2.41.1.2	INTEGER	read-write	This objects specifies the status of the LMI Spoofing.
INT dlcManagementDLCI	1.3.6.1.4.1.300.200.2.41.1.3	INTEGER	read-write	This objects specifies the number of management DLCI between 16 and 991 inclusive. Must not be the same as maintenance DLCI. Default is 989.
INT dlcManagementDLCIEnable	1.3.6.1.4.1.300.200.2.41.1.4	INTEGER	read-write	This object specifies whether to enable or disable Management DLCI.
INT dlcSpoofingProtocolType	1.3.6.1.4.1.300.200.2.41.1.5	INTEGER	read-write	This objects configures which LMI message type to 'spoof', in the event that spoofing is activated. The possible choices are FRF 1.0 (Frame Relay Forum's early LMI adaptation), Annex A (ITU Q.933, annex A), and Annex D (ANSI T1.617, annex D). Default is Annex D.
INT dlcDTESpoofingEnable	1.3.6.1.4.1.300.200.2.41.1.6	INTEGER	read-write	If the value of this object is 'enabled', LMI spoofing to the DTE port is done automatically.
INT dlcNetSpoofingEnable	1.3.6.1.4.1.300.200.2.41.1.7	INTEGER	read-write	If the value of this object is 'enabled', LMI spoofing to the Network port is done automatically.
INT dlcLinkIntegrityVerificationPollingTimer	1.3.6.1.4.1.300.200.2.41.1.8	INTEGER	read-write	This object is the interval in seconds between Link Integrity Verification Messages. This is known as T391 in the standards. Possible values are 5 to 30 seconds in increments of 5. Default is 10 seconds.
INT dlcFullStatusPollingCounter	1.3.6.1.4.1.300.200.2.41.1.9	INTEGER	read-write	This value corresponds to N391 in the ITU and ANSI standards. It is the number of polling cycles of the type before the unit generates the full status request. Possible values are 1 to 255. Default is 10.
INT dlcLMIErrorEvent	1.3.6.1.4.1.300.200.2.41.1.10	INTEGER	read-write	This object configures the parameter which sets the number of errors that can occur on the LMI link in LMI Error Monitored Events before reporting an interface down. Applies to the DTE and Network ports. This is used in the same manner as the N392 parameter (N2) in the standards. Possible values are 1 to 10. Default is 1.
INT dlcLMIErrorMonitorEvent	1.3.6.1.4.1.300.200.2.41.1.11	INTEGER	read-write	This object configures parameter which sets the number of events that are used with the LMI Error Event to define the error ratio that is used to report when the LMI link is down. Applies to the DTE and Network ports. This value is used in the same manner as the N393 parameter (N3) in the standards.
INT dlcLMIErrorFreeEvent	1.3.6.1.4.1.300.200.2.41.1.12	INTEGER	read-write	This object configures the parameter which sets the number of error-free messages that must be received in LMI Error Free Monitored Events prior to declaring an interface is up. Applies to the DTE and Network ports. For network spoofing, this is the number of error-free events that will cause the DSU to believe the network is back up and runnig, and the DSU will stop spoofing. This is used in the same manner as the N392 parameter (N2) in the standards. Possible values are 1 to 10. Default is 1.
INT dlcLMIErrorFreeMonitorEvent	1.3.6.1.4.1.300.200.2.41.1.13	INTEGER	read-write	This object configures parameter which sets the number of events that are used with the LMI Error Free Event to define the error ratio that is used to report that the LMI link is up. Applies to the DTE and Network ports. This is used in the same manner as the N393 parameter (N3) in the standards.
INT dlcDTEResponseTimer	1.3.6.1.4.1.300.200.2.41.1.14	INTEGER	read-write	This object configures the parameter which sets the number of seconds between the sending of a status enquiry message and the receipt of a response. Applies to the DTE port. This value is similar in nature to the T392 (T2) parameter in the standards. Possible values are 5 to 30 in increments of 5. Default is 15.
INT dlcLMIUnitLocation	1.3.6.1.4.1.300.200.2.41.1.15	INTEGER	read-write	This object configures where the unit is located so that LMI spoofing could be done properly. If 'cpe' is selected, it means the unit is located in Customer Premise. If 'co' is selected, the unit is in Central Office.
dlcLMIStatus	1.3.6.1.4.1.300.200.2.41.2
INT dlcSpoofingStatus	1.3.6.1.4.1.300.200.2.41.2.1	INTEGER	read-only	This object configures automatic LMI spoofing to the router. 'True' means LMI spoofing will occur automatically, 'False' means it's disabled.
INT dlcDTEInterfaceLMIStatus	1.3.6.1.4.1.300.200.2.41.2.2	INTEGER	read-only	This object indicates the LMI status of DTE interface.
INT dlcNetInterfaceLMIStatus	1.3.6.1.4.1.300.200.2.41.2.3	INTEGER	read-only	This object indicates the LMI status of Net interface.
INT dlcInbandDtePort	1.3.6.1.4.1.300.200.2.42	INTEGER	read-write	This object configures which DTE port has inband management.
dlcUnitStatus	1.3.6.1.4.1.300.200.3
UNI dlcUnitCurrentStatus	1.3.6.1.4.1.300.200.3.1	UnitStatusItem	read-only	What's going on in this unit?
GAU dlcUnitErrorFreeSeconds	1.3.6.1.4.1.300.200.3.2	Gauge	read-only	Represents the percent of error free seconds over the last 24 hours. The number is multiplied by 10 and rounded to the nearest integer. For example, 94.2% is encoded as 942.
INT dlcUnitLastSelfTestResult	1.3.6.1.4.1.300.200.3.3	INTEGER	read-only	The result of the last self test. unitLastSelfTest is a bitmap ... the sum of: 0 Selftest passed 1 ROM checksum failure 2 RAM test failure 4 EEPROM CRC failure 8 DTE test failure 16 Pattern loss during test 32 FLASH checksum failure 64 reserved 128 reserved 256 reserved 512 reserved A result of 0 means no errors occurred.
dlcUnitPortStatusTable	1.3.6.1.4.1.300.200.3.4		not-accessible	A table of all port-related status
dlcPortStatusEntry	1.3.6.1.4.1.300.200.3.4.1		not-accessible	An entry in the port status table.
POR dlcPortStatusId	1.3.6.1.4.1.300.200.3.4.1.1	PortId	read-only	Identifies which port (NET, AUX, Data DTE, or whatever) this status entry is describing.
POR dlcPortStatus	1.3.6.1.4.1.300.200.3.4.1.2	PortStatusItem	read-only	Gives the actual status value for to this port.
GAU dlcPortStatusNetRxBwUtilization	1.3.6.1.4.1.300.200.3.4.1.3	Gauge	read-only	Represents the percent of net receive bandwidth utilization over the last 60 seconds. The number is multiplied by 10 and rounded to the nearest integer. For example, 94.2% is encoded as 942.
GAU dlcPortStatusNetTxBwUtilization	1.3.6.1.4.1.300.200.3.4.1.4	Gauge	read-only	Represents the percent of net receive bandwidth utilization over the last 60 seconds. The number is multiplied by 10 and rounded to the nearest integer. For example, 94.2% is encoded as 942.
dlcUnitAlarmTable	1.3.6.1.4.1.300.200.3.5		not-accessible	A table of all currently-raised alarms
dlcAlarmEntry	1.3.6.1.4.1.300.200.3.5.1		not-accessible	An entry in the alarm table.
POR dlcAlarmPort	1.3.6.1.4.1.300.200.3.5.1.1	PortId	read-only	Identifies which port (NET, AUX, Data DTE, or whatever) this alarm relates to.
ALA dlcAlarmType	1.3.6.1.4.1.300.200.3.5.1.2	AlarmType	read-only	Identifies an alarm that's currently outstanding against this port.
GAU dlcUnitErrorSecondsRatio	1.3.6.1.4.1.300.200.3.6	Gauge	read-only	Represents the percent of error seconds over the last 24 hours. The number is multiplied by 10 and rounded to the nearest integer. For example, 94.2% is encoded as 942.
GAU dlcUnitSeverelyErroredSecondsRatio	1.3.6.1.4.1.300.200.3.7	Gauge	read-only	Represents the percent of severely errored seconds over the last 24 hours. The number is multiplied by 10 and rounded to the nearest integer. For example, 94.2% is encoded as 942.
GAU dlcUnitBackgroundBlockErrorRatio	1.3.6.1.4.1.300.200.3.8	Gauge	read-only	Represents the percent of background block errors over the last 24 hours. The number is multiplied by 10 and rounded to the nearest integer. For example, 94.2% is encoded as 942.
dlcUnitUserArchive	1.3.6.1.4.1.300.200.4
dlcUnitUserArchiveValidTable	1.3.6.1.4.1.300.200.4.1		not-accessible	A table of all port-related status
dlcUserArchiveValidEntry	1.3.6.1.4.1.300.200.4.1.1		not-accessible	An entry in the user archive valid-intervals table.
POR dlcValidPortId	1.3.6.1.4.1.300.200.4.1.1.1	PortId	read-only	Identifies which port (`net' or `otherNet') this entry is describing.
INT dlcValidIntervals	1.3.6.1.4.1.300.200.4.1.1.2	INTEGER	read-write	The number of valid intervals in the user's error register database for this port. Writing a 0 to this variable will clear the entire archive for this port. Writing any other value is a no-op.
dlcUnitUserLifetimeTable	1.3.6.1.4.1.300.200.4.2		not-accessible	A table of the lifetime error counts, per-port.
dlcUserLifetimeEntry	1.3.6.1.4.1.300.200.4.2.1		not-accessible	An entry in the user archive lifetime-totals table.
POR dlcLifetimePortId	1.3.6.1.4.1.300.200.4.2.1.1	PortId	read-only	Identifies which port (`net' or `otherNet') this entry relates to.
GAU dlcLifetimeES	1.3.6.1.4.1.300.200.4.2.1.2	Gauge	read-write	An ongoing count of Errored Seconds detected on this network port. Can be read and written (to zero).
GAU dlcLifetimeUAS	1.3.6.1.4.1.300.200.4.2.1.3	Gauge	read-write	An ongoing count of Unavailable Seconds detected on this network port. Can be read and written (to zero).
GAU dlcLifetimeCrcErrors	1.3.6.1.4.1.300.200.4.2.1.4	Gauge	read-write	An ongoing count of the CRC errors detected on this network port. Can be read and written (to zero).
GAU dlcLifetimeBpvErrors	1.3.6.1.4.1.300.200.4.2.1.5	Gauge	read-write	An ongoing count of the Code Violation errors detected on this network port. Can be read and written (to zero).
GAU dlcLifetimeOofErrors	1.3.6.1.4.1.300.200.4.2.1.6	Gauge	read-write	For an ESF T1 port, an ongoing count of Out-Of-Frame errors. For a D4 T1 port, an ongoing count of Framing Errors. Available only for the network port. Can be read and written (to zero).
GAU dlcLifetimeIbCrcErrors	1.3.6.1.4.1.300.200.4.2.1.7	Gauge	read-write	An ongoing count of the FCS errors detected on this network port.
dlcUnitUserCurrentTable	1.3.6.1.4.1.300.200.4.3		not-accessible	A table of all the current interval error counts, per-port.
dlcUserCurrentEntry	1.3.6.1.4.1.300.200.4.3.1		not-accessible	An entry in the user archive current interval table.
POR dlcCurrentPortId	1.3.6.1.4.1.300.200.4.3.1.1	PortId	read-only	Identifies which port (`net' or `otherNet') this entry relates to.
CTR dlcCurrentES	1.3.6.1.4.1.300.200.4.3.1.2	Counter	read-only	Errored seconds in the interval.
CTR dlcCurrentUAS	1.3.6.1.4.1.300.200.4.3.1.3	Counter	read-only	Unavailable seconds in the interval.
CTR dlcCurrentCrcErrors	1.3.6.1.4.1.300.200.4.3.1.4	Counter	read-only	CRC Errors in the interval.
CTR dlcCurrentBpvErrors	1.3.6.1.4.1.300.200.4.3.1.5	Counter	read-only	Code Violation Errors in the interval.
CTR dlcCurrentOofErrors	1.3.6.1.4.1.300.200.4.3.1.6	Counter	read-only	OOF or Framing Errors in the interval.
INT dlcCurrentTimeElapsed	1.3.6.1.4.1.300.200.4.3.1.7	INTEGER	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period. Available only for the network port.
CTR dlcCurrentIbCrcErrors	1.3.6.1.4.1.300.200.4.3.1.8	Counter	read-only	FCS Errors in the interval.
dlcUnitUserArchiveTable	1.3.6.1.4.1.300.200.4.4		not-accessible	A table of all the archive intervals' error counts, per-port.
dlcUserArchiveEntry	1.3.6.1.4.1.300.200.4.4.1		not-accessible	An entry in the user archive table.
POR dlcArchivePortId	1.3.6.1.4.1.300.200.4.4.1.1	PortId	read-only	Identifies which port (`net' or `otherNet') this entry relates to.
INT dlcArchiveInterval	1.3.6.1.4.1.300.200.4.4.1.2	INTEGER	read-only	Identifies which interval this secondaryArchiveEntry describes. 1 indicates the most-recent interval.
CTR dlcArchiveES	1.3.6.1.4.1.300.200.4.4.1.3	Counter	read-only	Errored seconds in the interval.
CTR dlcArchiveUAS	1.3.6.1.4.1.300.200.4.4.1.4	Counter	read-only	Unavailable seconds in the interval.
CTR dlcArchiveCrcErrors	1.3.6.1.4.1.300.200.4.4.1.5	Counter	read-only	CRC Errors in the interval.
CTR dlcArchiveBpvErrors	1.3.6.1.4.1.300.200.4.4.1.6	Counter	read-only	Code Violation Errors in the interval.
CTR dlcArchiveOofErrors	1.3.6.1.4.1.300.200.4.4.1.7	Counter	read-only	OOF or Framing Errors in the interval.
CTR dlcArchiveIbCrcErrors	1.3.6.1.4.1.300.200.4.4.1.8	Counter	read-only	FCS Errors in the interval.
GAU dlcArchiveNetRxBwUtilization	1.3.6.1.4.1.300.200.4.4.1.9	Gauge	read-only	Net Rx Bandwidth Utilization in the interval.
CTR dlcArchiveNetRxPackets	1.3.6.1.4.1.300.200.4.4.1.10	Counter	read-only	Net Rx Packets in the interval.
GAU dlcArchiveNetTxBwUtilization	1.3.6.1.4.1.300.200.4.4.1.11	Gauge	read-only	Net Tx Bandwidth Utilization in the interval.
CTR dlcArchiveNetTxPackets	1.3.6.1.4.1.300.200.4.4.1.12	Counter	read-only	Net Tx Packets in the interval.
dlcUnitTest	1.3.6.1.4.1.300.200.5
dlcUnitTestTable	1.3.6.1.4.1.300.200.5.1		not-accessible	A table containing all currently active tests. The initial release of the product's firmware does not include multiple tests. However, a later version will allow a number of tests to be active at a time. This MIB object structure allows any number of tests to be running at any time. Upon receiving a SET request, the unit compares this table with the list of currently active tests and terminates or initiates any tests as required. However, this does not apply to Link Based Test. dlcUnitConfigLinkTest group contains objects to configure and start Link Based Test. This table only contains the statistics for Link Based Test.
dlcUnitTestEntry	1.3.6.1.4.1.300.200.5.1.1		not-accessible	An entry in the network configuration table.
POR dlcUnitTestPortId	1.3.6.1.4.1.300.200.5.1.1.1	PortId	read-only	Identifies a port that a test might be running on. By convention, Self Test and all full-bandwidth tests (loopbacks, patterns, etc.) are assigned to the netPort. For E1 unit, if it is in unstructured mode, only full-bandwidth tests can be performed.
TES dlcUnitTestType	1.3.6.1.4.1.300.200.5.1.1.2	TestType	read-write	Says what test is running on this port. Note that the following test nomenclature is equivalent: SNMP Terminal UI Front Panel 1in8 1:7 1:7 3in24 3:24 3.24 1in1 1:1 1:1 AllOne All 1 1's AllZero All 0 0's 1in3 1:2 1:2 1in5 1:4 1:4 The SNMP test identifiers use the names on the left. The terminal User Interface uses the names in the middle column, and the unit's front panel uses the names in the right column.
INT dlcUnitTestPatternStatus	1.3.6.1.4.1.300.200.5.1.1.3	INTEGER	read-only	The current state of the Pattern Test module.
GAU dlcUnitTestPatternErrors	1.3.6.1.4.1.300.200.5.1.1.4	Gauge	read-write	An ongoing count of errors detected by the Pattern Generator/Detector. Can be read and written (to zero).
GAU dlcLinkTestSentPackets	1.3.6.1.4.1.300.200.5.1.1.5	Gauge	read-only	Number of sent packets for the currently running link based test.
GAU dlcLinkTestReceivedPackets	1.3.6.1.4.1.300.200.5.1.1.6	Gauge	read-only	Number of good received packets for the currently running link based test.
GAU dlcLinkTestErroredPackets	1.3.6.1.4.1.300.200.5.1.1.7	Gauge	read-only	Number of errored received packets for the currently running link based test.
GAU dlcLinkTestMissingPackets	1.3.6.1.4.1.300.200.5.1.1.8	Gauge	read-only	Number of missing packets for the currently running link based test.
GAU dlcLinkTestAverageRoundTrip	1.3.6.1.4.1.300.200.5.1.1.9	Gauge	read-only	Average round trip time in milli seconds for the currently running link based test.
GAU dlcLinkTestMaximumRoundTrip	1.3.6.1.4.1.300.200.5.1.1.10	Gauge	read-only	Maximum round trip time in milli seconds for the currently running link based test.
dlcUnitDelayMonitorStatus	1.3.6.1.4.1.300.200.6
dlcDelayMonitorStatusTable	1.3.6.1.4.1.300.200.6.1		not-accessible	Table of Delay Monitor status.
dlcDelayMonitorStatusEntry	1.3.6.1.4.1.300.200.6.1.1		not-accessible	An entry in the network configuration table.
INT dlcDelayMonitorStatusIndex	1.3.6.1.4.1.300.200.6.1.1.1	INTEGER	read-only	Uniquely identifies which Delay Monitor test in the configuration table.
GAU dlcDelayMonitorSentPackets	1.3.6.1.4.1.300.200.6.1.1.2	Gauge	read-only	Number of sent packets for the currently running delay monitor test.
GAU dlcDelayMonitorReceivedPackets	1.3.6.1.4.1.300.200.6.1.1.3	Gauge	read-only	Number of good received packets for the currently running delay monitor test.
GAU dlcDelayMonitorErroredPackets	1.3.6.1.4.1.300.200.6.1.1.4	Gauge	read-only	Number of errored received packets for the currently running delay monitor test.
GAU dlcDelayMonitorMissingPackets	1.3.6.1.4.1.300.200.6.1.1.5	Gauge	read-only	Number of missing packets for the currently running delay monitor test.
GAU dlcDelayMonitorAverageRoundTrip	1.3.6.1.4.1.300.200.6.1.1.6	Gauge	read-only	Average round trip time in milli seconds for the currently running delay monitor test.
GAU dlcDelayMonitorMaximumRoundTrip	1.3.6.1.4.1.300.200.6.1.1.7	Gauge	read-only	Maximum round trip time in milli seconds for the currently running delay monitor test.
dlcUtilizationTable	1.3.6.1.4.1.300.200.7		not-accessible	Table for lifetime Utilization statistics.
dlcUtilTableEntry	1.3.6.1.4.1.300.200.7.1		not-accessible	An entry for the utilization table.
INT dlcUtilDLCINumber	1.3.6.1.4.1.300.200.7.1.1	INTEGER	read-only	Identifies the DLCI number of the utilization statistics of this entry/row.
OCT dlcUtilEncodedValue	1.3.6.1.4.1.300.200.7.1.2	OCTET STRING	read-only	This object represents the value of the whole row of the table. The intent of object is to increase the efficiency of retrieving the table. For each object value in this table, which are all of Counter type, it will be represented with 4 bytes of data.
CTR dlcUtilTimestamp	1.3.6.1.4.1.300.200.7.1.3	Counter	read-only	Identifies timestamp when this entry is last updated.
CTR dlcUtilLessThan20	1.3.6.1.4.1.300.200.7.1.4	Counter	read-only	The number of times utilization is less than 20% of Committed Information Rate (CIR).
CTR dlcUtil20_40	1.3.6.1.4.1.300.200.7.1.5	Counter	read-only	The number of times utilization is between 20% and 40% of Committed Information Rate (CIR).
CTR dlcUtil40_60	1.3.6.1.4.1.300.200.7.1.6	Counter	read-only	The number of times utilization is between 40% and 60% of Committed Information Rate (CIR).
CTR dlcUtil60_80	1.3.6.1.4.1.300.200.7.1.7	Counter	read-only	The number of times utilization is between 60% and 80% of Committed Information Rate (CIR).
CTR dlcUtil80_100	1.3.6.1.4.1.300.200.7.1.8	Counter	read-only	The number of times utilization is between 80% and 100% of Committed Information Rate (CIR).
CTR dlcUtilMoreThan100	1.3.6.1.4.1.300.200.7.1.9	Counter	read-only	The number of times utilization is more than 100% of Committed Information Rate (CIR).

RFC description

Vendor-private extension MIB for DS1/T1 line management; extends RFC 1406 DSX1 MIB with vendor-specific counters.

Start monitoring Digital Link DSX1 (T1/E1) WAN access unit with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DL-NEW-DSX1-MIB

What Is DL-NEW-DSX1-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description