All MIBs › CPQHSV110V3-MIB
Category: Fibre Channel and Storage, Vendor: HP/HPE
Description: Provides management objects specific to the Compaq/HP StorageWorks HSV110 v3 array controller.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CPQHSV110V3-MIB?
CPQHSV110V3-MIB is a Compaq/HP StorageWorks MIB dedicated to the HSV110 v3 array controller, a Fibre Channel SAN storage controller used in HP's Enterprise Virtual Array (EVA) product line. Consistent with other Compaq/HP storage MIBs, it would expose controller identification, cache, host-port, and virtual-disk configuration and status objects specific to the HSV110 hardware revision. Its role is to monitor the hardware and operational status of the array controller itself - such as controller redundancy/failover state, cache battery status, and virtual disk health - as a hardware-focused complement to higher-level SAN appliance MIBs. It likely depends on or is layered beneath a broader Compaq/HP SAN appliance MIB (such as CPQAPPG80-MIB) that aggregates subsystem-level data across controller models. It is typically deployed in legacy HP StorageWorks EVA SAN environments where storage administrators monitor HSV110 controller health and virtual disk status. Engineers can download the CPQHSV110V3-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CPQHSV110V3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP StorageWorks HSV110 (EVA) array controller
Monitoring Examples
No sample object names were supplied for this MIB, so specific OIDs cannot be cited. Based on its role as an HSV110 v3 controller-specific module, an administrator would be expected to poll controller redundancy/failover state and virtual-disk/cache status to detect a failed controller or degraded virtual disk in an EVA storage array. This is a general characterization based on the module's stated scope rather than confirmed object names.
What Can Be Monitored
- controller redundancy/failover state
- cache/battery status
- virtual disk health
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| compaq | 1.3.6.1.4.1.232 | |||
| NTF emuEventTrapInformative | 1.3.6.1.4.1.232.0.136001 | An EMU Informational event has occurred scellNameDateTime: StorageCell name, and date/time emuShelfId: disk shelf number in the cabinet emuElementType: the element type 01: Disk 02: Pwr Supply 03: Fan 04: Temp Sensor 06: Alarm Horn 07: EMU 12: LCD 15: Xcvr 16: Lang 17: Comm Port 18: Volt Sensor 19: Amp Sensor 128:Encl 130:Back plane emuErrorCode: error number | ||
| NTF emuEventTrapNoncritical | 1.3.6.1.4.1.232.0.136002 | An EMU Non-critical event has occurred scellNameDateTime: StorageCell name, and date/time emuShelfId: disk shelf number in the cabinet emuElementType: the element type 01: Disk 02: Pwr Supply 03: Fan 04: Temp Sensor 06: Alarm Horn 07: EMU 12: LCD 15: Xcvr 16: Lang 17: Comm Port 18: Volt Sensor 19: Amp Sensor 128:Encl 130:Back plane emuErrorCode: error number | ||
| NTF emuEventTrapCritical | 1.3.6.1.4.1.232.0.136003 | An EMU Critical event has occurred scellNameDateTime: StorageCell name, and date/time emuShelfId: disk shelf number in the cabinet emuElementType: the element type 01: Disk 02: Pwr Supply 03: Fan 04: Temp Sensor 06: Alarm Horn 07: EMU 12: LCD 15: Xcvr 16: Lang 17: Comm Port 18: Volt Sensor 19: Amp Sensor 128:Encl 130:Back plane emuErrorCode: error number | ||
| NTF emuEventTrapUnrecoverable | 1.3.6.1.4.1.232.0.136004 | An EMU Unrecoverable event has occurred scellNameDateTime: StorageCell name, and date/time emuShelfId: disk shelf number in the cabinet emuElementType: the element type 01: Disk 02: Pwr Supply 03: Fan 04: Temp Sensor 06: Alarm Horn 07: EMU 12: LCD 15: Xcvr 16: Lang 17: Comm Port 18: Volt Sensor 19: Amp Sensor 128:Encl 130:Back plane emuErrorCode: error number | ||
| NTF sCellEventTrap10 | 1.3.6.1.4.1.232.0.13600256 | Severity: Normal -- informational in nature. During Executive Services initialization the system time value was set to the value contained in the time field. The action field contains one of the following codes which describes the condition that caused the time value to be chosen: 0 = TOY clock unavailable; time reset to default date and time. 1 = TOY clock time value was less than or equal to the last known time value previously stored in nonvolatile memory; time reset to default date and time. 2 = EDC was bad for last known time value previously stored in nonvolatile memory; time reset to default date and time. 3 = TOY clock not running; time reset to default date and time. 4 = TOY clock time value believed to be accurate; time set to TOY clock time value. | ||
| NTF sCellEventTrap11 | 1.3.6.1.4.1.232.0.13600257 | Severity: Normal -- informational in nature. The system time value was set to the value contained in the time field by a call to the EXEC$SETTIME service. As part of setting the time in a dual HSV110 controller configuration, the times are synchronized. The action field contains one of the following codes which describes the action taken: 0 = The time was set to the time value on this HSV110 controller. 1 = The master HSV110 controller requested the slave HSV110 controller to set its time to the time value. 2 = The slave HSV110 controller set the local time to the time value. 3 = The HSV110 controller's TOY clock was set to the time value. | ||
| NTF sCellEventTrap30 | 1.3.6.1.4.1.232.0.13600768 | Severity: Normal -- informational in nature. The HSV110 controller identified in the nodeName field has failed in communicating with the Cabinet (Rack) Bus Interface Controller. | ||
| NTF sCellEventTrap31 | 1.3.6.1.4.1.232.0.13600769 | Severity: Critical -- failure or failure imminent. The physical disk drive identified by the device field has been rendered inoperable. If the flags.quorumDisk flag is nonzero, the physical disk drive is the Storage System Quorum disk identified in the quorumSequence field. If the flags.inqState flag is nonzero, the content of the inqData and capacity fields is valid. If the rssFlags.memberAbnormal flag is nonzero, the content of the memberState field is valid. The rackNum field will not be valid until a future release. The reasonCode field contains a code giving the reason the physical disk drive has been rendered inoperable: 0x001 = CS IO failure 0x002 = Scrubber IO failure 0x003 = Attempt to set CBIT on normal drive 0x004 = Attempt to set CBIT on merging drive 0x100 = The Target Discovery Service Descriptor retry count has been exceeded 0x101 = Inoperable for Bad Block Replacement 0x102 = The soft error count has been exceeded 0x103 = The number of exchange timeouts permitted was exceeded 0x104 = Communication with drive has failed an excessive number of times 0x105 = The number of retries has been exceeded 0x106 = Medium/Hardware Errors encountered on this physical disk drive 0x107 = The number of Directed LIP's has surpassed the threshold 0x200 = Smart event from a physical disk drive not in Storage System 0x201 = Smart event from a physical disk drive not a Volume 0x202 = Smart event from a physical disk drive not a RSS 0x203 = Failure predicted from physical disk drive 0x204 = Can't read from physical disk drive from the poll 0x205 = Failure predicted from physical disk drive while deleting Disk Group 0x206 = physical disk drive forced inoperative from maintenance command for temporary POID 0x207 = physical disk drive forced inoperative from maintenance command for POID 0x208 = Bad block recovery failed or can't read FPAB 0x209 = Failure to remove volume from Storage System 0x20A = Failure to update metadata | ||
| NTF sCellEventTrap32 | 1.3.6.1.4.1.232.0.13600770 | Severity: Warning -- not failed but attention recommended or required. A physical disk drive will not be used because the maximum number of physical disk drives already exist in the current Storage System. The affected physical disk drive is identified in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The location of the physical disk drive is contained in the rackNum, denclNum, and bay fields. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the reasonCode, flags, rssFlags, inqData, quorumSequence, capacity, and memberState fields is undefined. | ||
| NTF sCellEventTrap33 | 1.3.6.1.4.1.232.0.13600771 | Severity: Normal -- informational in nature. A HSV110 controller has begun booting. That controller is identified in the nodeName field. Note that in this case the content of the scellTag field is undefined. | ||
| NTF sCellEventTrap34 | 1.3.6.1.4.1.232.0.13600772 | Severity: Normal -- informational in nature. The HSV110 controller identified in the nodeName field has finished the process of bringing the Storage System, identified in the scellTag field, online. | ||
| NTF sCellEventTrap35 | 1.3.6.1.4.1.232.0.13600773 | Severity: Normal -- informational in nature. The HSV110 controller identified in the nodeName field has been joined into the Storage System. | ||
| NTF sCellEventTrap36 | 1.3.6.1.4.1.232.0.13600774 | Severity: Normal -- informational in nature. The HSV110 controller identified in the nodeName field has been ousted from the Storage System identified in the scellTag field. | ||
| NTF sCellEventTrap37 | 1.3.6.1.4.1.232.0.13600775 | Severity: Normal -- informational in nature. The HSV110 controller identified in the nodeName field is now the Storage System, identified in the scellTag field, master. | ||
| NTF sCellEventTrap38 | 1.3.6.1.4.1.232.0.13600776 | Severity: Normal -- informational in nature. The HSV110 controller identified in the nodeName field has been brought into the Storage System identified in the scellTag field. | ||
| NTF sCellEventTrap40 | 1.3.6.1.4.1.232.0.13601024 | Severity: Undetermined -- more information needed to determine severity. HSV110 controller operation was terminated due to an unrecoverable event detected by either software or hardware or due to an action initiated via the Storage System Management Interface. | ||
| NTF sCellEventTrap41 | 1.3.6.1.4.1.232.0.13601025 | Severity: Undetermined -- more information needed to determine severity. An HSV110 controller has sent a last gasp message prior to terminating operation. The terminated HSV110 controller is identified in the lter.terminatingCtrlr field. The lter.terminationEvent.u.value field contains the termination cause (i.e., termination code). The lter.terminationEvent.terminationLocation field contains the termination location. The lter.terminationTime field contains the termination date and time. The lter.seq field contains the index of the HSV110 controller's Last Termination Event Array element assigned to the termination event. The lter.swVersion, lter.baselevelId, and lter.ctrlrModelId fields identify the software level and controller model information. The lter.uptime field contains a value that represents the number of seconds the HSV110 controller has executed functional code since its first power up. Note that the reportingCtrlr header field identifies the HSV110 controller that received the last gasp message. All other header fields reflect information supplied by the terminating controller. | ||
| NTF sCellEventTrap42 | 1.3.6.1.4.1.232.0.13601026 | Severity: Critical -- failure or failure imminent. A machine check occurred while a termination event was being processed. The post-termination operation being performed at the time the event occurred can be derived from the lter.reueaIndex field. Note: The lteihd and lter fields may not describe the event that caused the HSV110 controller to terminate operation depending on how far termination processing got before the machine check occurred. | ||
| NTF sCellEventTrap43 | 1.3.6.1.4.1.232.0.13601027 | Severity: Critical -- failure or failure imminent. An unexpected event occurred while a termination event was being processed. The value contained in the uei.type field describes the event as follows: 0 = Unrecognized Unexpected Event code. 1 = Power failure before initialization could complete. 2 = Recursive termination before initialization could complete. 3 = Terminated during the first part post-termination preparation. 4 = Terminated during the load of the G3 Glue registers. 5 = Terminated during the second part post-termination preparation. 6 = Terminated during event report block load. 7 = Terminated during initialization of all hardware components and software data structures in preparation for restart. 8 = Terminated during execution of an unrecognized post-termination operation (premature). 9 = Power failure during execution of a post-termination operation. A = No good entries found in Termination Event Array. (Note that this condition is expected following the first boot of a newly manufactured HSV110 controller. In that case this event can be safely ignored; no action is necessary.) B = The EDC of one or more Termination Event Array entries is bad. C = Termination Event Array entry control block revision is different. D = Termination Event Array entry information block revision is different. E = Termination Event Array entry up time value is greater than the system's up time value. F = Termination Event Array entry up time value is less than the previous entry's up time value. 10= Termination Event Array entry sequence number value is less than the previous entry's sequence number value. 11= Detected an unrecognized dump/restart control code. 12= Failed to terminate the entity dump loop. 13= Unexpected dump entity size. 14= Unexpected Event Log Packet processing stage code. 15= Number of Termination Parameters supplied not equal to maximum allowed as required. The post-termination operation being performed at the time the unexpected event occurred is contained in the uei.pto field. Note: The lteihd and lter fields may not describe the event that caused the HSV110 controller to terminate operation depending on how far termination processing got before the unexpected event occurred. | ||
| NTF sCellEventTrap44 | 1.3.6.1.4.1.232.0.13601028 | Severity: Normal -- informational in nature. The Storage System Event Log validation completed successfully. The content of the cinfo.scelcbi.status field, the cinfo.scelcbi structure, and the minfo.scelmi structure show the validated state of the Storage System Event Log. The meaning of the status value contained in the cinfo.scelcbi.status field is as follows: 0 = No problems found. Note: The content of the ainfo fields, cinfo.sctelcbi structure, and minfo.sctelmi structure is undefined. | ||
| NTF sCellEventTrap45 | 1.3.6.1.4.1.232.0.13601029 | Severity: Normal -- informational in nature. The Storage System Event Log validation failed. The content of the cinfo.scelcbi.status field, the cinfo.scelcbi structure, and the minfo.scelmi structure show the state of the Storage System Event Log at the time of the failure. The content and state of the Storage System Event Log have been initialized to their initial operational settings. The meaning of the status value contained in the cinfo.scelcbi.status field is as follows: 1 = Cookie value is not as expected. 2 = Event data overflows the buffer. 3 = Event data size is not a multiple of 4 bytes, is less than the minimum, or is greater than the maximum. 4 = Event Information Packet type is greater than the maximum. 5 = Event information size is not a multiple of 4 bytes, is less than the minimum, is greater than the maximum, doesn't match the Event Information Packet type size, or when combined with the entry header size doesn't equal the entry size. 6 = Event code is zero. 7 = Event is out of sequence. 8 = Dead space area at the end of a partially packed buffer contains a nonzero value. 9 = An event data block containing a nonzero value was found after end of event data was detected. A = Sequence number reset flag not set as expected. B = The event log contains no entries. C = Event data block read failed during maintenance verification. D = Event data block read failed during maintenance completion. E = Event data block erase failed during maintenance completion. F = Control block read failed during maintenance verification. 17= The event log was destroyed and prepared for re-initialization. Note: The content of the ainfo fields, cinfo.sctelcbi structure, and minfo.sctelmi structure is undefined. | ||
| NTF sCellEventTrap46 | 1.3.6.1.4.1.232.0.13601030 | Severity: Critical -- failure or failure imminent. Event reports were lost due to an insufficient supply of Event Log Packets on the HSV110 controller that is the Storage System Master. The ainfo.eventsNotReported field shows the number of event reports lost. Note: The content of the ainfo.quiesceType field, ainfo.remoteEvent field cinfo.sctelcbi structure, and minfo.sctelmi structure is undefined. | ||
| NTF sCellEventTrap47 | 1.3.6.1.4.1.232.0.13601031 | Severity: Critical -- failure or failure imminent. Event reports were lost due to an insufficient supply of Event Log Packets on the HSV110 controller that is not the Storage System Master. The ainfo.eventsNotReported field shows the number of event reports lost. Note: The content of the ainfo.quiesceType field, ainfo.remoteEvent field cinfo.sctelcbi structure, and minfo.sctelmi structure is undefined. | ||
| NTF sCellEventTrap48 | 1.3.6.1.4.1.232.0.13601032 | Severity: Normal -- informational in nature. The Storage System Termination Event Log has become inaccessible. The content of the cinfo.sctelcbi.status field, the cinfo.sctelcbi structure, and the minfo.sctelmi structure show the current state of the Storage System Termination Event Log. The meaning of the status value contained in the cinfo.sctelcbi.status field is as follows: F = Control block read failed during maintenance verification. 10= Control block write failed during maintenance verification. 11= Event data block write failed during maintenance update. 12= Control block write failed during maintenance completion. 13= Storage System Termination Event Log related send was unsuccessful or the master found that the Storage System Termination Event Log is inaccessible. 16= Event data block read failed during retrieval request. Note: The content of the ainfo fields, cinfo.scelcbi structure, and minfo.scelmi structure is undefined. | ||
| NTF sCellEventTrap49 | 1.3.6.1.4.1.232.0.13601033 | Severity: Normal -- informational in nature. The Storage System Termination Event Log validation completed successfully. The content of the cinfo.sctelcbi.status field, the cinfo.sctelcbi structure, and the minfo.sctelmi structure show the validated state of the Storage System Termination Event Log. The meaning of the status value contained in the cinfo.sctelcbi.status field is as follows: 0 = No problems found. Note: The content of the ainfo fields, cinfo.scelcbi structure, and minfo.scelmi structure is undefined. | ||
| NTF sCellEventTrap4A | 1.3.6.1.4.1.232.0.13601034 | Severity: Normal -- informational in nature. The Storage System Termination Event Log validation failed. The content of the cinfo.sctelcbi.status field, the cinfo.sctelcbi structure, and the minfo.sctelmi structure show the state of the Storage System Termination Event Log at the time of the failure. The meaning of the status value contained in the cinfo.sctelcbi.status field is as follows: F = Control block read failed during maintenance verification. 10= Control block write failed during maintenance verification. 11= Event data block write failed during maintenance update. 12= Control block write failed during maintenance completion. 13= Storage System Termination Event Log related send was unsuccessful or the master found that the Storage System Termination Event Log is inaccessible. 16= Event data block read failed during retrieval request. 17= The log was destroyed and prepared for re-initialization. Note: The content of the ainfo fields, cinfo.scelcbi structure, and minfo.scelmi structure is undefined. | ||
| NTF sCellEventTrap4B | 1.3.6.1.4.1.232.0.13601035 | Severity: Normal -- informational in nature. The Storage System Termination Event Log has been updated with the termination event information obtained from the HSV110 controller that is not the Storage System Master. The content of the cinfo.sctelcbi.status field, the cinfo.sctelcbi structure, and the minfo.sctelmi structure show the updated state of the Storage System Termination Event Log. The meaning of the status value contained in the cinfo.sctelcbi.status field is as follows: 0 = No problems found. Note: The content of the ainfo fields, cinfo.scelcbi structure, and minfo.scelmi structure is undefined. | ||
| NTF sCellEventTrap4C | 1.3.6.1.4.1.232.0.13601036 | Severity: Critical -- failure or failure imminent. The Fault Manager on the Storage System Master received an invalid Event Information Packet from the remote Fault Manager. The header information from the invalid Event Information Packet is contained in the ainfo.remoteEvent field. Note: The content of the ainfo.quiesceType field, ainfo.eventsNotReported field, cinfo.scelcbi structure, cinfo.sctelcbi structure, minfo.scelmi structure, and minfo.sctelmi structure is undefined. | ||
| NTF sCellEventTrap4D | 1.3.6.1.4.1.232.0.13601037 | Severity: Normal -- informational in nature. The Fault Manager operation was made quiescent. If the ainfo.quiesceType field is equal to 0, the operation was performed on both HSV110 controllers. If the ainfo.quiesceType field is equal to 1, the operation was performed only on the HSV110 controller that is not the Storage System Master. Note: The content of the ainfo.eventsNotReported field, cinfo.scelcbi structure, cinfo.sctelcbi structure, minfo.scelmi structure, and minfo.sctelmi structure is undefined. | ||
| NTF sCellEventTrap4E | 1.3.6.1.4.1.232.0.13601038 | Severity: Undetermined -- more information needed to determine severity. An HSV110 controller sent a last gasp message prior to terminating operation with an indication that the HSV110 controller identified in the lter.terminatingCtrlr field should also terminate operation. | ||
| NTF sCellEventTrap4F | 1.3.6.1.4.1.232.0.13601039 | Severity: Normal -- informational in nature. This HSV110 controller sent its termination event information to the HSV110 controller that is the Storage System Master. The content of the cinfo.sctelcbi.status field, the cinfo.sctelcbi structure, and the minfo.sctelmi structure show the updated state of the Storage System Termination Event Log. The meaning of the status value contained in the cinfo.sctelcbi.status field is as follows: 0 = No problems found. Note: The content of the ainfo fields, cinfo.scelcbi structure, and minfo.scelmi structure is undefined. | ||
| NTF sCellEventTrap410 | 1.3.6.1.4.1.232.0.13601040 | Severity: Critical -- failure or failure imminent. Event reports were lost due to an insufficient supply of ISR Event Log Packets on the HSV110 controller that is the Storage System Master. The ainfo.eventsNotReported field shows the number of event reports lost. Note: The content of the ainfo.quiesceType field, ainfo.remoteEvent field cinfo.sctelcbi structure, and minfo.sctelmi structure is undefined. | ||
| NTF sCellEventTrap411 | 1.3.6.1.4.1.232.0.13601041 | Severity: Critical -- failure or failure imminent. Event reports were lost due to an insufficient supply of ISR Event Log Packets on the HSV110 controller that is not the Storage System Master. The ainfo.eventsNotReported field shows the number of event reports lost. Note: The content of the ainfo.quiesceType field, ainfo.remoteEvent field cinfo.sctelcbi structure, and minfo.sctelmi structure is undefined. | ||
| NTF sCellEventTrap60 | 1.3.6.1.4.1.232.0.13601536 | Severity: Critical -- failure or failure imminent. A physical disk drive has reported that it has exceeded its failure prediction threshold. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the physical disk drive is contained in the cmd field. The sense data obtained from the physical disk drive as a result of the failure prediction threshold exceeded error is contained in the error field. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap61 | 1.3.6.1.4.1.232.0.13601537 | Severity: Warning -- not failed but attention recommended or required. A Fibre Channel port on the HSV110 controller has failed to respond. The identity of the affected Fibre Channel port is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number of the affected Fibre Channel port is contained in the port field. The peb array contains the port event block information. The peqFrzProdIndex field contains the index to the port event block in use when the Tachyon chip entered the frozen state. The peqProdIndex field contains the index to the next port event block. The peqConsIndex field contains the index to the next port event block to be acted upon. The failureCause field contains the internal routing value as follows: 1 - Excessive exchange timeouts on loop 2 - Excessive link errors on loop 3 - Exhausted Link Down retries on loop with signal 4 - Exhausted Link Down retries on loop with loss of signal 5 - Excessive link inits on loop without completing device discovery | ||
| NTF sCellEventTrap62 | 1.3.6.1.4.1.232.0.13601538 | Severity: Normal -- informational in nature. A physical disk drive has reported a check condition error. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the physical disk drive is contained in the cmd field. The sense data obtained from the physical disk drive as a result of the check condition error is contained in the error field. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap63 | 1.3.6.1.4.1.232.0.13601539 | Severity: Warning -- not failed but attention recommended or required. An exchange sent to a physical disk drive or another HSV110 controller via the mirror port or a Fibre Channel port has timed out. The identity of the intended recipient is contained in the device field. The Fibre Channel port over which the frame was sent is identified in the cerpId field. The HSV110 controller internal Fibre Channel port number over which the frame was sent is contained in the port field. The arbitrated loop physical address of the intended recipient is contained in the alPa field. The missingPort and missingCerpId fields are unused. The location of the intended recipient is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The number of timeouts detected is contained in the numTimes field. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap64 | 1.3.6.1.4.1.232.0.13601540 | Severity: Warning -- not failed but attention recommended or required. Work was unexpectedly sent to this HSV110 controller by a physical disk drive or another HSV110 controller. This HSV110 controller did not originate the work. The identity of the sender is contained in the device field. The Fibre Channel port over which the unexpected work was received is identified in the cerpId field. The HSV110 controller internal Fibre Channel port number over which the unexpected work was received is contained in the port field. The arbitrated loop physical address of the sender is contained in the alPa field. The location of the sender is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The hdrCdb field contains the command descriptor block and Fibre Channel header information associated with the unexpected work. | ||
| NTF sCellEventTrap65 | 1.3.6.1.4.1.232.0.13601541 | Severity: Warning -- not failed but attention recommended or required. Work has been sent to a physical disk drive or another HSV110 controller via the mirror port but it did not respond. The identity of the intended target is contained in the device field. The Fibre Channel port over which the work was sent is identified in the cerpId field. The HSV110 controller internal Fibre Channel port over which the work was sent is contained in the port field. The arbitrated loop physical address of the intended target is contained in the alPa field. The location of the intended target is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the intended target is contained in the cmd field. Note that in this case the content of the error field is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap67 | 1.3.6.1.4.1.232.0.13601543 | Severity: Warning -- not failed but attention recommended or required. A Target Discovery Service Descriptor exchange sent to a physical disk drive has timed out. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the physical disk drive is contained in the cmd field. Note that in this case the content of the error field is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap68 | 1.3.6.1.4.1.232.0.13601544 | Severity: Normal -- informational in nature. An excessive number of link errors were detected on a HSV110 controller's Fibre Channel port. The identity of the affected Fibre Channel port is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number of the affected Fibre Channel port is contained in the port field. This is an informational event triggered by the occurrence of an excessive number of Tachyon chip link status errors detected within a particular link status error type. The number of occurrences of each link status error type is contained in a separate type-specific field (e.g., lossOfSignal, badRxChar, etc.). The HSV110 controller checks each of its Fibre Channel port's for excessive link status errors periodically. | ||
| NTF sCellEventTrap69 | 1.3.6.1.4.1.232.0.13601545 | Severity: Critical -- failure or failure imminent. A physical disk drive has reported numerous failure prediction threshold exceeded errors. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The missingPort and missingCerpId fields are unused. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The numTimes field is the number of failure prediction threshold exceeded errors reported by the physical disk drive in the previous minute. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap6A | 1.3.6.1.4.1.232.0.13601546 | Severity: Normal -- informational in nature. A physical disk drive has reported numerous check condition errors. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The missingPort and missingCerpId fields are unused. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The numTimes field is the number of check condition errors reported by the physical disk drive in the previous minute. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap6B | 1.3.6.1.4.1.232.0.13601547 | Severity: Warning -- not failed but attention recommended or required. A non-data exchange sent to a physical disk drive has timed out. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the physical disk drive is contained in the cmd field. Note that in this case the content of the error field is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap6C | 1.3.6.1.4.1.232.0.13601548 | Severity: Normal -- informational in nature. A loop switch has been detected on a Fibre Channel port. The identity of the Fibre Channel port is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number is contained in the port field. Note that in this case the content of the device, alPa, rackNum, denclNum, bay, fedClass and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The missingPort and missingCerpId fields are unused. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap6D | 1.3.6.1.4.1.232.0.13601549 | Severity: Normal -- informational in nature. The location of a physical disk drive previously reported as unknown is now known. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The missingPort and missingCerpId fields are unused. The location of the physical disk drive is contained in the rackNum, denclNum, and bay fields. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of fedClass, alPa and numTimes fields are undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap6E | 1.3.6.1.4.1.232.0.13601550 | Severity: Critical -- failure or failure imminent. A Drive Enclosure Environmental Monitoring Unit requested a code update but the code update could not be found, so the update was not performed. The identity of the affected Drive Enclosure Environmental Monitoring Unit is contained in the device field. The Fibre Channel port used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the port field. The missingPort and missingCerpId fields are unused. The location of the Drive Enclosure Environmental Monitoring Unit is contained in the rackNum and denclNum fields. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the alPa, bay, fedClass and numTimes field is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap6F | 1.3.6.1.4.1.232.0.13601551 | Severity: Critical -- failure or failure imminent. The Drive Enclosure Environmental Monitoring Unit is able to communicate with a physical disk drive but this HSV110 controller is unable to communicate with that physical disk drive on the Fibre Channel bus. The identity of the Drive Enclosure Environmental Monitoring Unit is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The missingPort and missingCerpId fields are unused. The location of the physical disk drive is contained in the rackNum, denclNum, and bay fields. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the alPa, fedClass and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap610 | 1.3.6.1.4.1.232.0.13601552 | Severity: Undetermined -- more information needed to determine severity. A HSV110 controller is unable to communicate with this Drive Enclosure Environmental Monitoring Unit. The Drive Enclosure Environmental Monitoring Unit identified in the device field has stopped communicating with the HSV110 controller. The Fibre Channel port used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the port field. The missingPort and missingCerpId fields are unused. The location of the Drive Enclosure Environmental Monitoring Unit is contained in the rackNum and denclNum fields. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the bay, alPa, fedClass and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap612 | 1.3.6.1.4.1.232.0.13601554 | Severity: Normal -- informational in nature. The retry count for a task assigned to a Drive Enclosure Environmental Monitoring Unit has been exhausted. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The peb array contains the task list that was intended to be sent to the Drive Enclosure Environmental Monitoring Unit. The peqFrzProdIndex field contains the task that was being retried. The peqProdIndex field contains the drive enclosure where the physical disk drive used to communicate with the Drive Enclosure Environmental Monitoring Unit is located. The peqConsIndex field identifies the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) used to communicate with the physical disk drive that was used to communicate with the Drive Enclosure Environmental Monitoring Unit. The failureCause field contains the bay where the physical disk drive used to communicate with the Drive Enclosure Environmental Monitoring Unit. | ||
| NTF sCellEventTrap613 | 1.3.6.1.4.1.232.0.13601555 | Severity: Normal -- informational in nature. A Drive Enclosure Environmental Monitoring Unit is able to communicate with this HSV110 controller. The identity of the Drive Enclosure Environmental Monitoring Unit is contained in the device field. The Fibre Channel port used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the port field. The missingPort and missingCerpId fields are unused. The location of the Drive Enclosure Environmental Monitoring Unit is contained in the rackNum and denclNum fields. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the bay, fedClass and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap614 | 1.3.6.1.4.1.232.0.13601556 | Severity: Critical -- failure or failure imminent. There are too many drive enclosures attached to a Fibre Channel port. The Fibre Channel port with too many drive enclosures attached to the HSV110 controller is contained in the cerpId field. Note that in this case the content of the bay, fedClass, rackNum, denclNum and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The missingPort and missingCerpId fields are unused. The location of the identified in the cerpId field. The device, missingPort and missingCerpId fields are unused. The location of the physical disk drive is determined by the content of the denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap615 | 1.3.6.1.4.1.232.0.13601557 | Severity: Critical -- failure or failure imminent. The cable connected to the I/O module is attached to the wrong Fibre Channel port. The Fibre Channel port incorrectly attached to the HSV110 controller is contained in the cerpId field. Note that in this case the content of the device, missingPort, missingCerpId, bay, fedClass, rackNum, denclNum and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap616 | 1.3.6.1.4.1.232.0.13601558 | Severity: Critical -- failure or failure imminent. A HSV110 controller does not have an address on the enclosure address bus. The HSV110 controller location cannot be identified. Note that in this case the content of the missingPort, missingCerpId, bay, fedClass, rackNum, denclNum, alPa, device, cerpId, port, enclosures array and numTimes fields is undefined. | ||
| NTF sCellEventTrap618 | 1.3.6.1.4.1.232.0.13601560 | Severity: Normal -- informational in nature. A Drive Enclosure Environmental Monitoring Unit has begun updating its code. Do not power down this drive enclosure until the code update has completed. The identity of the Drive Enclosure Environmental Monitoring Unit is contained in the device field. The Fibre Channel port used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the port field. The missingPort and missingCerpId fields are unused. The location of the Drive Enclosure Environmental Monitoring Unit is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. In addition, the device field may contain all zeroes. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that the content of the fedClass, alPa, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap619 | 1.3.6.1.4.1.232.0.13601561 | Severity: Normal -- informational in nature. A Drive Enclosure Environmental Monitoring Unit has completed updating its code. It is now safe to power down this drive enclosure. The identity of the Drive Enclosure Environmental Monitoring Unit is contained in the device field. The Fibre Channel port used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Drive Enclosure Environmental Monitoring Unit is contained in the port field. The missingPort and missingCerpId fields are unused. The location of the Drive Enclosure Environmental Monitoring Unit is contained in the rackNum and denclNum fields. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass, alPa, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap61a | 1.3.6.1.4.1.232.0.13601562 | Severity: Critical -- failure or failure imminent. A physical disk drive has exceeded its soft error threshold. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass, cdb, and senseData fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap61b | 1.3.6.1.4.1.232.0.13601563 | Severity: Normal -- informational in nature. A HSV110 controller now has an address on the enclosure address bus. The HSV110 controller location has been identified. The location of the HSV110 controller is contained in the rackNum and denclNum fields. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the bay, fedClass, alPa, cerpId, port, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The missingPort and missingCerpId fields are unused. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap61c | 1.3.6.1.4.1.232.0.13601564 | Severity: Warning -- not failed but attention recommended or required. An outbound frame targeted to a physical disk drive has timed out. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the physical disk drive is contained in the cmd field. Note that in this case the content of the error field is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap61d | 1.3.6.1.4.1.232.0.13601565 | Severity: Warning -- not failed but attention recommended or required. A Fibre Channel exchange to a physical disk drive has completed but is missing data. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the physical disk drive is contained in the cmd field. Note that in this case the content of the error field is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap61e | 1.3.6.1.4.1.232.0.13601566 | Severity: Critical -- failure or failure imminent. A HSV110 controller has detected only one port of a Fibre Channel device. This Fibre Channel device has entered the Single Port on Fibre state which should be corrected as soon as possible. The identity of the Fibre Channel device is contained in the device field. The Fibre Channel port still able to communicate with the Fibre Channel device is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number able to communicate with the Fibre Channel device is contained in the port field. The Fibre Channel port unable to communicate with the Fibre Channel device is contained in the missingCerpId field. The HSV110 controller internal Fibre Channel port number unable to communicate with the Fibre Channel device is contained in the missingPort field. The arbitrated loop physical address of the Fibre Channel device is contained in the alPa field. The location of the Fibre Channel device is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap61f | 1.3.6.1.4.1.232.0.13601567 | Severity: Normal -- informational in nature. A previously reported Fibre Channel device with only one port has been corrected and redundancy has been restored. The device is no longer in the Single Port on Fibre state. The identity of the Fibre Channel device is contained in the device field. The Fibre Channel port used to communicate with the Fibre Channel device is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Fibre Channel device is contained in the port field. The missingPort and missingCerpId fields are unused. The arbitrated loop physical address of the Fibre Channel device is contained in the alPa field. The location of the Fibre Channel device is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap620 | 1.3.6.1.4.1.232.0.13601568 | Severity: Critical -- failure or failure imminent. An unsupported Fibre Channel device has been detected. The drive has been failed to prevent possible data corruption or system instability. The identity of the Fibre Channel device is contained in the device field. The Fibre Channel port used to communicate with the Fibre Channel device is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Fibre Channel device is contained in the port field. The arbitrated loop physical address of the Fibre Channel device is contained in the alPa field. The missingPort and missingCerpId fields are unused. The location of the Fibre Channel device is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap621 | 1.3.6.1.4.1.232.0.13601569 | Severity: Normal -- informational in nature. A Fibre Channel device with the incorrect block size has been detected. The identity of the Fibre Channel device is contained in the device field. The Fibre Channel port used to communicate with the Fibre Channel device is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Fibre Channel device is contained in the port field. The arbitrated loop physical address of the Fibre Channel device is contained in the alPa field. The missingPort and missingCerpId fields are unused. The location of the Fibre Channel device is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap623 | 1.3.6.1.4.1.232.0.13601571 | Severity: Normal -- informational in nature. A HSV110 controller is about to retry a failed port. The Fibre Channel port that is about to be retried is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number about to be retried is contained in the port field. Note that in this case the content of the bay, rackNum, fedClass, alPa, denclNum, device, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The missingPort and missingCerpId fields are unused. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap624 | 1.3.6.1.4.1.232.0.13601572 | Severity: Normal -- informational in nature. A HSV110 controller has successfully retried a failed port. The Fibre Channel port that has been restarted is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number that has been restarted is contained in the port field. Note that in this case the content of the bay, rackNum, fedClass, alPa, denclNum, device, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The missingPort and missingCerpId fields are unused. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap625 | 1.3.6.1.4.1.232.0.13601573 | Severity: Critical -- failure or failure imminent. A Drive Enclosure Environmental Monitoring Unit has failed to assign a hard address to a physical disk drive on the loop. The device field contains the identity of the enclosure. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The alPa field contains the expected ALPA, and the numTimes field contains the actual ALPA. The missingPort and missingCerpId fields are unused. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note that in this case the content of the fedClass is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap626 | 1.3.6.1.4.1.232.0.13601574 | Severity: Critical -- failure or failure imminent. A Drive Enclosure Environmental Monitoring Unit has failed to assign an address to a physical disk drive on the loop. This has occurred because another physical disk drive has already obtained this ALPA. The device field contains the identity of the enclosure. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The alPa field contains the ALPA that was stolen. The missingPort and missingCerpId fields are unused. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap627 | 1.3.6.1.4.1.232.0.13601575 | Severity: Critical -- failure or failure imminent. A Drive Enclosure Environmental Monitoring Unit has failed to assign address(s) to a physical disk drive on the loop. Soft addressing was detected for this enclosure. The device field contains the identity of the enclosure. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The missingPort and missingCerpId fields are unused. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass, alPa, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap628 | 1.3.6.1.4.1.232.0.13601576 | Severity: Normal -- informational in nature. The retry count for an OB task assigned to a Drive Enclosure Environmental Monitoring Unit has been exhausted. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The peb array contains the task list that was intended to be sent to the Drive Enclosure Environmental Monitoring Unit. The peqFrzProdIndex field contains the task that was being retried. The peqProdIndex field contains the drive enclosure where the physical disk drive used to communicate with the Drive Enclosure Environmental Monitoring Unit is located. The peqConsIndex field identifies the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) used to communicate with the physical disk drive that was used to communicate with the Drive Enclosure Environmental Monitoring Unit. The failureCause field contains the bay where the physical disk drive used to communicate with the Drive Enclosure Environmental Monitoring Unit. | ||
| NTF sCellEventTrap629 | 1.3.6.1.4.1.232.0.13601577 | Severity: Normal -- informational in nature. The HSV110 controller has sent a Basic Link Service command Abort Sequence Frame. The original work is described in this event. The identity of the intended target is contained in the device field. The Fibre Channel port over which the work was sent is identified in the cerpId field. The HSV110 controller internal Fibre Channel port over which the work was sent is contained in the port field. The arbitrated loop physical address of the intended target is contained in the alPa field. The location of the intended target is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the intended target is contained in the cmd field. Note that in this case the content of the error field is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap62a | 1.3.6.1.4.1.232.0.13601578 | Severity: Normal -- informational in nature. The HSV110 controller has sent an Extended Link Service command Reinstate Recovery Qualifier. The original work is described in this event. The identity of the intended target is contained in the device field. The Fibre Channel port over which the work was sent is identified in the cerpId field. The HSV110 controller internal Fibre Channel port over which the work was sent is contained in the port field. The arbitrated loop physical address of the intended target is contained in the alPa field. The location of the intended target is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fedClass field. The command issued to the intended target is contained in the cmd field. Note that in this case the content of the error field is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap62b | 1.3.6.1.4.1.232.0.13601579 | Severity: Critical -- failure or failure imminent. A physical disk drive was bypassed rendering it unusable. The physical disk drive is unusable because a Drive Enclosure Environmental Monitoring Unit bypassed a drive bay or the physical disk drive left itself bypassed. The physical disk drive is not available to the HSV110 controllers and will not be displayed by the HSV element manager GUI. The physical disk drive fault led will be lit to indicate that it is unusable. The Fibre Channel port over which this condition was detected is identified in the cerpId field. The HSV110 controller internal Fibre Channel port over which this condition was detected is contained in the port field. The alPa field is invalid. The location of the physical disk drive is as indicated by the content of the rackNum, denclNum, and bay fields. Note that the content of the rackNum field will not be valid until a future release. The bypassReason field is used to indicate how the physical disk drive was bypassed: 1 = The physical disk drive left itself bypassed 2 = The Drive Enclosure Environmental Monitoring Unit bypassed the drive bay The Drive Enclosure Environmental Monitoring Unit is identified in the device field. Additionally, the content of the pid, rev, and enclosures array fields is undefined in this case. | ||
| NTF sCellEventTrap62c | 1.3.6.1.4.1.232.0.13601580 | Severity: Normal -- informational in nature. One or more media defects were detected on a physical disk drive. The affected physical disk drive is identified in the device field. The Fibre Channel port over which the media defect(s) was detected is identified in the cerpId field. The HSV110 controller internal Fibre Channel port number over which the media defect(s) was detected is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The Logical Block Address of each media defect is contained in a separate entry of the hdrCdb array. Only nonzero values in the hdrCdb array entries are valid. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap62d | 1.3.6.1.4.1.232.0.13601581 | Severity: Normal -- informational in nature. An HSV110 controller issued a directed LIP to an arbitrated loop physical address. The Fibre Channel port over which the directed LIP was issued is identified in the cerpId field. The HSV110 controller internal Fibre Channel port number over which the directed LIP was issued is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. | ||
| NTF sCellEventTrap62e | 1.3.6.1.4.1.232.0.13601582 | Severity: Normal -- informational in nature. An HSV110 controller has detected Loop Receiver Failures. The Fibre Channel port over which the Loop Receiver Failures were detected is identified in the cerpId field. The HSV110 controller internal Fibre Channel port number over which the Loop Receiver Failures were detected is contained in the port field. The counts and the ALPAs of the Loop Receiver Failures are contained in a separate entry of the hdrCdb array. Only nonzero values in the hdrCdb array entries are valid. The affected HSV110 controller is identified in the device field. Note that in this case the content of the alPa, denclNum, bay, and rackNum fields are undefined. | ||
| NTF sCellEventTrap630 | 1.3.6.1.4.1.232.0.13601584 | Severity: Critical -- failure or failure imminent. A HSV110 controller has detected only one port of all Fibre Channel devices in an enclosure. These Fibre Channel devices have entered the Single Port on Fibre state which should be corrected as soon as possible. The identity of the Fibre Channel device enclosure is contained in the device field. The Fibre Channel port still able to communicate with the Fibre Channel device is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number able to communicate with the Fibre Channel device is contained in the port field. The Fibre Channel port unable to communicate with the Fibre Channel device is contained in the missingCerpId field. The HSV110 controller internal Fibre Channel port number unable to communicate with the Fibre Channel device is contained in the missingPort field. The alPa and bay fields are invalid. The location of the Fibre Channel enclosure is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap631 | 1.3.6.1.4.1.232.0.13601585 | Severity: Normal -- informational in nature. A previously reported Fibre Channel device enclosure with only one port has been corrected and redundancy has been restored. The devices in the enclosure are no longer in the Single Port on Fibre state. The identity of the Fibre Channel device enclosure is contained in the device field. The Fibre Channel port used to communicate with the Fibre Channel device enclosure is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Fibre Channel device is contained in the port field. The alPa, bay, missingPort, and missingCerpId fields are invalid. The location of the Fibre Channel device is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. Note also that in this case the content of the fedClass, and numTimes fields is undefined. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap632 | 1.3.6.1.4.1.232.0.13601586 | Severity: Critical -- failure or failure imminent. A HSV110 controller has detected only one port of all Fibre Channel devices on a loop. These Fibre Channel devices have entered the Single Port on Fibre state which should be corrected as soon as possible. The device, alPa, denclNum, and bay fields are all invalid. The Fibre Channel port still able to communicate with the Fibre Channel device is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number able to communicate with the Fibre Channel device is contained in the port field. The Fibre Channel port unable to communicate with the Fibre Channel device is contained in the missingCerpId field. The HSV110 controller internal Fibre Channel port number unable to communicate with the Fibre Channel device is contained in the missingPort field. | ||
| NTF sCellEventTrap633 | 1.3.6.1.4.1.232.0.13601587 | Severity: Normal -- informational in nature. A previously reported Fibre Channel loop with only one port has been corrected and redundancy has been restored. The devices on the loop are no longer in the Single Port on Fibre state. The device, alPa, denclNum, bay, missingPort, and missingCerpId fields are invalid. The Fibre Channel port used to communicate with the Fibre Channel devices is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the Fibre Channel devices is contained in the port field. | ||
| NTF sCellEventTrap634 | 1.3.6.1.4.1.232.0.13601588 | Severity: Normal -- informational in nature. A HSV110 controller has been told to enable a device port, and that device port was not disabled during boot diagnostics. The Fibre Channel port that was enabled is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number enabled is contained in the port field. Note that in this case the contents of the bay, rackNum, fedClass, alPa, denclNum, device, enclosure array, and numTimes fields are undefined. The missingPort and missingCerpId fields are unused. | ||
| NTF sCellEventTrap635 | 1.3.6.1.4.1.232.0.13601589 | Severity: Critical -- failure or failure imminent. An unrecognized Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The bypassReason field is invalid. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum, alPa and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The newRev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap636 | 1.3.6.1.4.1.232.0.13601590 | Severity: Critical -- failure or failure imminent. An unsupported Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The bypassReason field is invalid. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum, alPa and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The newRev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap637 | 1.3.6.1.4.1.232.0.13601591 | Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that is later than the latest known supported revision. If the location information is 0, it indicates the type of drive, not a specific drive. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The bypassReason field is invalid. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum, alPa and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The newRev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap638 | 1.3.6.1.4.1.232.0.13601592 | Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available. If the location information is 0, it indicates the type of drive, not a specific drive. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the alPa field. The bypassReason field is invalid. The location of the physical disk drive is determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum, denclNum, and bay fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum, alPa and bay fields is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum, denclNum, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. Note that the content of the rackNum field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The newRev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerpId field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap639 | 1.3.6.1.4.1.232.0.13601593 | Severity: Normal -- informational in nature. The HSV110 controller bypassed a device bay in an attempt to restore operability. The identity of the bay is indicated by the rackNum, denclNum, and bay fields. All other fields are invalid. | ||
| NTF sCellEventTrap63a | 1.3.6.1.4.1.232.0.13601594 | Severity: Normal -- informational in nature. The HSV110 controller is attempting to recovery devices on the indicated port. All other fields are invalid. | ||
| NTF sCellEventTrap63b | 1.3.6.1.4.1.232.0.13601595 | Severity: Normal -- informational in nature. The HSV110 controller has finished error recovery attempts on the indicated port. All other fields are invalid. | ||
| NTF sCellEventTrap63c | 1.3.6.1.4.1.232.0.13601596 | Severity: Normal -- informational in nature. The HSV110 controller been requested to unbypass device bays on the indicated port. All other fields are invalid. | ||
| NTF sCellEventTrap63d | 1.3.6.1.4.1.232.0.13601597 | Severity: Undetermined -- more information needed to determine severity. The HSV110 controller has detected a enclosure on the CAB bus that does not have a Fibre Channel connection. All fields except port and rack are invalid. other fields are invalid. | ||
| NTF sCellEventTrap63e | 1.3.6.1.4.1.232.0.13601598 | Severity: Critical -- failure or failure imminent. The HSV110 controller has detected an enclosure on the Fibre Channel but is unable to communicate with the EMU on the CAB bus or the EMU is reporting an invalid enclosure number. All fields except port and rack are invalid. other fields are invalid. | ||
| NTF sCellEventTrap70 | 1.3.6.1.4.1.232.0.13601792 | Severity: Warning -- not failed but attention recommended or required. Allocation of a Virtual Disk has stalled due to insufficient space in the Disk Group caused by the failure or pulling of a physical disk drive. The tag1 field contains the identity of the Virtual Disk. The tag2 field contains the identity of the Disk Group. The values that may be found in the state field are as follows: 0 = Attempting to retry the allocation 1 = Awaiting a leveling event (a drive needs to be inserted) | ||
| NTF sCellEventTrap71 | 1.3.6.1.4.1.232.0.13601793 | Severity: Warning -- not failed but attention recommended or required. Expansion of a Virtual Disk has stalled due to insufficient space in the Disk Group caused by the failure or pulling of a physical disk drive. The tag1 field contains the identity of the Virtual Disk. The tag2 field contains the identity of the Disk Group. The values that may be found in the state field are as follows: 0 = Attempting to retry the expansion 1 = Awaiting a leveling event (a drive needs to be inserted) | ||
| NTF sCellEventTrap72 | 1.3.6.1.4.1.232.0.13601794 | Severity: Normal -- informational in nature. Leveling of capacity in a Disk Group has started. The identity of the Disk Group is contained in the tag1 field. | ||
| NTF sCellEventTrap73 | 1.3.6.1.4.1.232.0.13601795 | Severity: Normal -- informational in nature. Leveling of capacity in a Disk Group has finished. The identity of the Disk Group is contained in the tag1 field. | ||
| NTF sCellEventTrap74 | 1.3.6.1.4.1.232.0.13601796 | Severity: Normal -- informational in nature. A member management operation has started due to the appearance or disappearance of a physical disk drive. If available, the tag1 field contains the identity of the physical disk drive. The tag2 field contains the disk unit block in which physical disk drive resides. The values that may be found in the state field are as follows: 2 = Reconstructing 4 = Migrating 6 = Reverting | ||
| NTF sCellEventTrap75 | 1.3.6.1.4.1.232.0.13601797 | Severity: Normal -- informational in nature. A member management operation has finished. If available, the tag1 field contains the identity of the physical disk drive. The tag2 field contains the disk unit block in which the physical disk drive resides. The values that may be found in the state field are as follows: 2 = Reconstructing 4 = Migrating 6 = Reverting The status field contains one of the following values: 1 = PSEGS NONE ( Reconstruction of data was successful ) 2 = PSEGS RAID0 ( Could not reconstruct RAID0 data ) 4 = PSEGS RAID5 ( Could not reconstruct RAID5 data ) 8 = PSEGS RAID1 ( Could not reconstruct RAID1 data ) | ||
| NTF sCellEventTrap76 | 1.3.6.1.4.1.232.0.13601798 | Severity: Normal -- informational in nature. A Disk Group has started changing its internal structure due to the appearance or disappearance of a Volume. The identity of the Disk Group is contained in the tag1 field. The values that may be found in the state field are as follows: 4 = Merge began 8 = Split began | ||
| NTF sCellEventTrap77 | 1.3.6.1.4.1.232.0.13601799 | Severity: Normal -- informational in nature. A Disk Group has finished changing its internal structure due to the appearance or disappearance of a volume. The identity of the Disk Group is contained in the tag1 field. The values that may be found in the state field are as follows: 4 = Merge completed 8 = Split completed | ||
| NTF sCellEventTrap78 | 1.3.6.1.4.1.232.0.13601800 | Severity: Normal -- informational in nature. Deallocation of a Virtual Disk has failed after three attempts due to unknown circumstances. This will more than likely be caused by failing physical drives. The deletion will be restarted when a resync/reboot occurs. The tag1 field contains the identity of the Virtual Disk. The tag2 field contains the identity of the Disk Group. The values that may be found in the status field indicate the returned status from the delete operation. | ||
| NTF sCellEventTrap91 | 1.3.6.1.4.1.232.0.13602305 | Severity: Normal -- informational in nature. The state of the Physical Disk Drive identified in the handle field has transitioned to the NORMAL state. The value.ul1 field contains the new state: 1 (NORMAL). The value.ul2 field contains the old state. The state values that may be in the value.ul2 field are as follows: 2 = Degraded 3 = Failed 4 = Not present 5 = Single Port on Fibre The enclosure number, bay number, and rack number where the Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], attribute.value.u32[2] fields, respectively. The attribute.type field contains value 1. The rack number in the attribute.value.u32[2] field will not contain a valid value until a future release. | ||
| NTF sCellEventTrap92 | 1.3.6.1.4.1.232.0.13602306 | Severity: Normal -- informational in nature. The state of a Volume has changed. The identity of the affected Volume is contained in the handle field. The addHandle field contains the identity of the Physical Disk Drive that is associated with that Volume. The enclosure number, bay number, and rack number where the associated Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], and attribute.value.u32[2] fields, respectively. The internal identification of that Volume's Redundant Storage Set is contained in the attribute.value.u32[3] field. The attribute.type field contains the value of 1. The value.ul1 field contains the new state. The value.ul2 field contains the old state. The state values that may be found in the value.ul1 and value.ul2 fields are as follows: 1 = Normal - Volume is present and operating normally 2 = Migrating - Data from this volume is being moved to other storage in this Disk Group 3 = Missing - Volume is inaccessible 4 = Reconstructing - Volume is inaccessible; redundant data is being regenerated and moved to other storage in this Disk Group 5 = Completing - This previously inaccessible volume has become accessible; data migration is being completed 6 = Reverting - This previously inaccessible volume has become accessible; data is being regenerated 7 = Failed - Volume is not being used in the Disk Group; disk errors are preventing normal usage | ||
| NTF sCellEventTrap93 | 1.3.6.1.4.1.232.0.13602307 | Severity: Normal -- informational in nature. The state of the internal Logical Disk associated with the Virtual Disk identified in the handle field has changed. The value.ul1 field contains the new state. The value.ul2 field contains the old state. The state values that may be found in the value.ul1 and value.ul2 fields are as follows: 1 = Normal 2 = Replacement delay in progress 3 = Redundancy lost, restore in progress 4 = Redundancy lost, restore stalled 5 = Failed 6 = Creation in progress 7 = Snapshot is inoperative due to lack of snapshot space 8 = Deletion in progress 9 = Capacity change in progress 10 = Inoperative due to data lost 11 = Capacity reservation in progress 12 = Capacity unreservation in progress | ||
| NTF sCellEventTrap94 | 1.3.6.1.4.1.232.0.13602308 | Severity: Normal -- informational in nature. The state of the HSV110 controller identified in the handle field has transitioned to the NORMAL state. The value.ul1 field contains the new state: 1 (NORMAL). The value.ul2 field contains the old state: 3 (FAILED). | ||
| NTF sCellEventTrap95 | 1.3.6.1.4.1.232.0.13602309 | Severity: Normal -- informational in nature. The state of a battery assembly within the HSV110 controller identified in the handle field has changed. The value.ul1 field contains the new state. The value.ul2 field contains the old state. The state values that may be found in the value.ul1 and value.ul2 fields are as follows: 1 = Battery System Hold-up Time is greater than 96 hours 3 = Battery System Hold-up Time is greater than 0 and less than 96 hours 5 = Battery System Hold-up Time is zero hours | ||
| NTF sCellEventTrap96 | 1.3.6.1.4.1.232.0.13602310 | Severity: Undetermined -- more information needed to determine severity. A Volume has transitioned to the MISSING state. The affected Volume is identified in the handle field. The addHandle field contains the identity of the Physical Disk Drive that is associated with that Volume. The enclosure number, bay number, and rack number where the associated Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], and attribute.value.u32[2] fields, respectively. The internal identification of that Volume's Redundant Storage Set is contained in the attribute.value.u32[3] field. The attribute.type field contains the value of 1. The value.ul1 field contains the new state. The value.ul2 field contains the old state. The state values that may be found in the value.ul1 and value.ul2 fields are as follows: 1 = Normal - Volume is present and operating normally 2 = Migrating - Data from this volume is being moved to other storage in this Disk Group 4 = Reconstructing - Volume is inaccessible; redundant data is being regenerated and moved to other storage in this Disk Group 5 = Completing - This previously inaccessible volume has become accessible; data migration is being completed 6 = Reverting - This previously inaccessible volume has become accessible; data is being regenerated 7 = Failed - Volume is not being used in the Disk Group; disk errors are preventing normal usage | ||
| NTF sCellEventTrap97 | 1.3.6.1.4.1.232.0.13602311 | Severity: Normal -- informational in nature. The state of the Fibre Channel port identified in the attribute.value.str field and located on the rear panel of the HSV110 controller identified in the handle field has transitioned to the NORMAL state. The attribute.type field contains the value 4. The value.ul1 field contains the new state: 1 (NORMAL). The value.ul2 field contains the old state: 2 (FAILED). Note that the HSV110 controller's internal identity of the affected Fibre Channel port is contained in the secondaryId field. | ||
| NTF sCellEventTrap98 | 1.3.6.1.4.1.232.0.13602312 | Severity: Warning -- not failed but attention recommended or required. The Occupancy Alarm Level threshold has been reached for the Disk Group identified in the handle field. | ||
| NTF sCellEventTrap99 | 1.3.6.1.4.1.232.0.13602313 | Severity: Normal -- informational in nature. The Resource Availability state of a Volume has transitioned to the SUFFICIENT state. The affected Volume is identified in the handle field. The addHandle field contains the identity of the Physical Disk Drive that is associated with that Volume. The enclosure number, bay number, and rack number where the associated Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], and attribute.value.u32[2] fields, respectively. The internal identification of that Volume's Redundant Storage Set is contained in the attribute.value.u32[3] field. The attribute.type field contains the value of 1. The value.ul1 field contains the new state: 0 (SUFFICIENT). The value.ul2 field contains the old state: 1 (INSUFFICIENT). | ||
| NTF sCellEventTrap9A | 1.3.6.1.4.1.232.0.13602314 | Severity: Normal -- informational in nature. The Data Availability state of the internal Logical Disk associated with the Virtual Disk identified in the handle field has transitioned to the NORMAL state. The value.ul1 field contains the new state: 0 (NORMAL). The value.ul2 field contains the old state: 1 (DATA LOST). | ||
| NTF sCellEventTrap9C | 1.3.6.1.4.1.232.0.13602316 | Severity: Normal -- informational in nature. The Snapclone Logical Disk identified in the handle field has completed the unsharing operation. The secondaryId field contains the noid of the associated successor internal Logical Disk. | ||
| NTF sCellEventTrap9D | 1.3.6.1.4.1.232.0.13602317 | Severity: Normal -- informational in nature. The state of the Quorum Disk flag of a Volume has changed. The affected Volume is identified in the handle field. The value.ul1 field contains the new state of the Quorum Disk flag. The value.ul2 field contains the old state of the Quorum Disk flag. The state values that may be found in the value.ul1 and value.ul2 fields are as follows: 0 = Not quorum disk 1 = Quorum disk | ||
| NTF sCellEventTrap9E | 1.3.6.1.4.1.232.0.13602318 | Severity: Critical -- failure or failure imminent. The temperature trip point for a temperature sensor located within an HSV110 controller has been reached. The HSV110 controller is identified in the handle field. The value.ul1 field contains the current temperature reading from I2C sensor 1 in degrees celsius while the value.ul2 field contains the adjusted reading from I2C sensor 2. The set temperature trip point is contained in the secondaryId field. | ||
| NTF sCellEventTrap9F | 1.3.6.1.4.1.232.0.13602319 | Severity: Warning -- not failed but attention recommended or required. The temperature within the HSV110 controller identified in the handle field is approaching its trip point. The value.ul1 field contains the current temperature reading from I2C sensor 1 in degrees celsius while the value.ul2 field contains the adjusted reading from I2C sensor 2. The secondaryId field contains the set temperature trip point in Celsius. | ||
| NTF sCellEventTrap911 | 1.3.6.1.4.1.232.0.13602321 | Severity: Normal -- informational in nature. The Blower Present flag for the '1' blower assembly located within the HSV110 controller identified in the handle field has transitioned from the NOT PRESENT to PRESENT state indicating that the blower has been reinstalled. The secondaryId field contains the '1' blower assembly internal identifier value: 1. The value.ul1 field contains the new state of the Blower Present flag: 1 (PRESENT). The value.ul2 field contains the old state of the Blower Present flag: 0 (NOT PRESENT). | ||
| NTF sCellEventTrap912 | 1.3.6.1.4.1.232.0.13602322 | Severity: Critical -- failure or failure imminent. The '1' blower located within the HSV110 controller identified in the handle field is running slower than the lowest acceptable speed. The secondaryId field contains the '1' blower assembly internal identifier value: 1. The value.ul1 field contains the current speed of the '1' blower. The value.ul2 field contains the lowest acceptable speed for the '1' blower. | ||
| NTF sCellEventTrap913 | 1.3.6.1.4.1.232.0.13602323 | Severity: Normal -- informational in nature. One of the voltage sensors located within the HSV110 controller identified in the handle field has reported a voltage that is out of range. The value.ul1 field contains the out of range voltage value. The secondaryId field contains the specific voltage threshold value (i.e., 12V, 5V, 3.3V, 2.5V or 2V). Note that the voltages are expressed in millivolts--e.g.,12.5V is expressed as 12500. | ||
| NTF sCellEventTrap914 | 1.3.6.1.4.1.232.0.13602324 | Severity: Undetermined -- more information needed to determine severity. The state of a Volume has transitioned to the FAILED state. The affected Volume is identified in the handle field. The addHandle field contains the identity of the Physical Disk Drive that is associated with that Volume. The enclosure number, bay number, and rack number where the associated Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], and attribute.value.u32[2] fields, respectively. The internal identification of that Volume's Redundant Storage Set is contained in the attribute.value.u32[3] field. The attribute.type field contains the value of 1. The value.ul1 field contains the new state: 7 (FAILED). The value.ul2 field contains the old state. The state values that may be found in the value.ul2 fields are as follows: 1 = Normal - Volume is present and operating normally 2 = Migrating - Data from this volume is being moved to other storage in this Disk Group 3 = Missing - Volume is inaccessible 4 = Reconstructing - Volume is inaccessible; redundant data is being regenerated and moved to other storage in this Disk Group 5 = Completing - This previously inaccessible volume has become accessible; data migration is being completed 6 = Reverting - This previously inaccessible volume has become accessible; data is being regenerated | ||
| NTF sCellEventTrap915 | 1.3.6.1.4.1.232.0.13602325 | Severity: Undetermined -- more information needed to determine severity. An HSV110 controller has failed. The state of the HSV110 controller identified in the handle field has transitioned to the FAILED state. The value.ul1 field contains the new state: 3 (FAILED). The value.ul2 field contains the old state: 1 (NORMAL). | ||
| NTF sCellEventTrap916 | 1.3.6.1.4.1.232.0.13602326 | Severity: Normal -- informational in nature. The temperature within the HSV110 controller identified in the handle field has returned to its normal operating range. The value.ul1 field contains the current temperature reading in celsius from I2C sensor 1, while the value.ul2 field contains the adjusted reading from I2C sensor 2. | ||
| NTF sCellEventTrap917 | 1.3.6.1.4.1.232.0.13602327 | Severity: Critical -- failure or failure imminent. An HSV110 controller's battery assembly has been removed. The Battery Present flag for battery assembly '1' located within the HSV110 controller identified in the handle field has changed from PRESENT to NOT PRESENT indicating that the battery assembly was removed. The secondaryId field contains the battery assembly '1' internal identifier value: 1. The value.ul1 field contains the new state of the Battery Present flag: 0 (NOT PRESENT). The value.ul2 field contains the old state of the Battery Present flag: 1 (PRESENT). | ||
| NTF sCellEventTrap918 | 1.3.6.1.4.1.232.0.13602328 | Severity: Normal -- informational in nature. The Battery In Use flag for battery assembly '1' located within the HSV110 controller identified in the handle field has transitioned from the NOT IN USE to IN USE state indicating that the battery assembly is functioning properly. The secondaryId field contains the battery assembly '1' internal identifier value: 1. The value.ul1 field contains the new state of the Battery In Use flag: 1 (IN USE). The value.ul2 field contains the old state of the Battery In Use flag: 0 (NOT IN USE). | ||
| NTF sCellEventTrap919 | 1.3.6.1.4.1.232.0.13602329 | Severity: Normal -- informational in nature. One of the voltage sensors located within the HSV110 controller identified in the handle field has reported a voltage that indicates that a voltage that was previously out of range has returned to the normal range. The value.ul1 field contains the normal range voltage value. The secondaryId field contains the voltage threshold value (i.e., 12V, 5V, 3.3V, 2.5V or 2V). Note that the voltages are expressed in thousands--e.g., 12.5V is expressed as 12500. | ||
| NTF sCellEventTrap91a | 1.3.6.1.4.1.232.0.13602330 | Severity: Warning -- not failed but attention recommended or required. The battery assembly voltage regulator located within the HSV110 controller identified in the handle field is offline. | ||
| NTF sCellEventTrap91b | 1.3.6.1.4.1.232.0.13602331 | Severity: Normal -- informational in nature. The state of the Disk Group identified in the handle field has transitioned to the NORMAL state. The value.ul1 field contains the new Disk Group state: 1 (NORMAL). The value.ul2 field contains the old Disk Group state. The state values that may be found in the value.ul2 field are as follows: 2 = Disk Group with no redundancy is inoperative 3 = Disk Group with parity redundancy is inoperative 4 = Disk Group with mirrored redundancy is inoperative 5 = Disk Group with no redundancy is inoperative, marked for re-use 6 = Disk Group with parity redundancy is inoperative, marked for re-use 7 = Disk Group with mirrored redundancy is inoperative, marked for re-use | ||
| NTF sCellEventTrap91c | 1.3.6.1.4.1.232.0.13602332 | Severity: Normal -- informational in nature. The Occupancy Alarm Level for the Disk Group identified in the handle field has returned to the normal range. | ||
| NTF sCellEventTrap91d | 1.3.6.1.4.1.232.0.13602333 | Severity: Critical -- failure or failure imminent. An HSV110 controller's battery assembly has malfunctioned. The Battery In Use flag for battery assembly '1' located within the HSV110 controller identified in the handle field has transitioned from the IN USE to NOT IN USE state indicating that the battery assembly has malfunctioned. The secondaryId field contains the battery assembly '1' internal identifier value: 1. The value.ul1 field contains the new state of the Battery In Use flag: 0 (NOT IN USE). The value.ul2 field contains the old state of the Battery In Use flag: 1 (IN USE). | ||
| NTF sCellEventTrap91e | 1.3.6.1.4.1.232.0.13602334 | Severity: Normal -- informational in nature. The Battery Present flag for battery assembly '1' located within the HSV110 controller identified in the handle field has changed from NOT PRESENT to PRESENT indicating that the battery assembly was reinstalled. The secondaryId field contains the battery assembly '1' internal identifier value: 1. The value.ul1 field contains the new state of the Battery Present flag: 1 (PRESENT). The value.ul2 field contains the old state of the Battery Present flag: 0 (NOT PRESENT). | ||
| NTF sCellEventTrap91f | 1.3.6.1.4.1.232.0.13602335 | Severity: Critical -- failure or failure imminent. An HSV110 controller's battery assembly has been removed. The Battery Present flag for battery assembly '2' located within the HSV110 controller identified in the handle field has changed from PRESENT to NOT PRESENT indicating that the battery assembly was removed. The secondaryId field contains the battery assembly '2' internal identifier value: 2. The value.ul1 field contains the new state of the Battery Present flag: 0 (NOT PRESENT). The value.ul2 field contains the old state of the Battery Present flag: 1 (PRESENT). | ||
| NTF sCellEventTrap920 | 1.3.6.1.4.1.232.0.13602336 | Severity: Normal -- informational in nature. The Battery Present flag for battery assembly '2' located within the HSV110 controller identified in the handle field has changed from NOT PRESENT to PRESENT indicating that the battery assembly was reinstalled. The secondaryId field contains the battery assembly '2' internal identifier value: 2. The value.ul1 field contains the new state of the Battery Present flag: 1 (PRESENT). The value.ul2 field contains the old state of the Battery Present flag: 0 (NOT PRESENT). | ||
| NTF sCellEventTrap921 | 1.3.6.1.4.1.232.0.13602337 | Severity: Normal -- informational in nature. The Battery In Use flag for battery assembly '2' located within the HSV110 controller identified in the handle field has transitioned from the NOT IN USE to IN USE state indicating that the battery assembly is functioning properly. The secondaryId field contains the battery assembly '2' internal identifier value: 2. The value.ul1 field contains the new state of the Battery In Use flag: 1 (IN USE). The value.ul2 field contains the old state of the Battery In Use flag: 0 (NOT IN USE). | ||
| NTF sCellEventTrap922 | 1.3.6.1.4.1.232.0.13602338 | Severity: Critical -- failure or failure imminent. An HSV110 controller's battery assembly has malfunctioned. The Battery In Use flag for battery assembly '2' located within the HSV110 controller identified in the handle field has transitioned from the IN USE to NOT IN USE state indicating that the battery assembly has malfunctioned. The secondaryId field contains the battery assembly '2' internal identifier value: 2. The value.ul1 field contains the new state of the Battery In Use flag: 0 (NOT IN USE). The value.ul2 field contains the old state of the Battery In Use flag: 1 (IN USE). | ||
| NTF sCellEventTrap923 | 1.3.6.1.4.1.232.0.13602339 | Severity: Critical -- failure or failure imminent. The Blower Present flag for the '2' blower assembly located within the HSV110 controller identified in the handle field has transitioned from the PRESENT to NOT PRESENT state indicating that the blower has been removed. The secondaryId field contains the '2' blower assembly internal identifier value: 2. The value.ul1 field contains the new state of the Blower Present flag: 0 (NOT PRESENT). The value.ul2 field contains the old state of the Blower Present flag: 1 (PRESENT). | ||
| NTF sCellEventTrap924 | 1.3.6.1.4.1.232.0.13602340 | Severity: Normal -- informational in nature. The Blower Present flag for the '2' blower assembly located within the HSV110 controller identified in the handle field has transitioned from the NOT PRESENT to PRESENT state indicating that the blower has been reinstalled. The secondaryId field contains the '2' blower assembly internal identifier value: 2. The value.ul1 field contains the new state of the Blower Present flag: 1 (PRESENT). The value.ul2 field contains the old state of the Blower Present flag: 0 (NOT PRESENT). | ||
| NTF sCellEventTrap925 | 1.3.6.1.4.1.232.0.13602341 | Severity: Critical -- failure or failure imminent. The '2' blower located within the HSV110 controller identified in the handle field is running slower than the lowest acceptable speed. The secondaryId field contains the '2' blower assembly internal identifier value: 2. The value.ul1 field contains the current speed of the '2' blower. The value.ul2 field contains the lowest acceptable speed for the '2' blower. | ||
| NTF sCellEventTrap926 | 1.3.6.1.4.1.232.0.13602342 | Severity: Critical -- failure or failure imminent. An HSV110 controller's '1' blower/power supply assembly has been removed or AC power has been removed from the power supply. The HSV110 controller is identified in the handle field. The secondaryId field contains the '1' blower/power supply assembly internal identifier value: 1. The value.ul1 field contains the new state of the Blower/Power Supply Present flag: 0 (NOT PRESENT). The value.ul2 field contains the old state of the Blower/Power Supply Present flag: 1 (PRESENT). | ||
| NTF sCellEventTrap927 | 1.3.6.1.4.1.232.0.13602343 | Severity: Normal -- informational in nature. An HSV110 controller's '1' blower/power supply assembly has been reinstalled or AC power has been restored to the power supply. The HSV110 controller is identified in the handle field. The secondaryId field contains the '1' blower/power supply assembly internal identifier value: 1. The value.ul1 field contains the new state of the Blower/Power Supply Present flag: 1 (PRESENT). The value.ul2 field contains the old state of the Blower/Power Supply Present flag: 0 (NOT PRESENT). | ||
| NTF sCellEventTrap928 | 1.3.6.1.4.1.232.0.13602344 | Severity: Critical -- failure or failure imminent. An HSV110 controller's '2' blower/power supply assembly has been removed or AC power has been removed from the power supply. The HSV110 controller is identified in the handle field. The secondaryId field contains the '2' blower/power supply assembly internal identifier value: 2. The value.ul1 field contains the new state of the Blower/Power Supply Present flag: 0 (NOT PRESENT). The value.ul2 field contains the old state of the Blower/Power Supply Present flag: 1 (PRESENT). | ||
| NTF sCellEventTrap929 | 1.3.6.1.4.1.232.0.13602345 | Severity: Normal -- informational in nature. An HSV110 controller's '2' blower/power supply assembly has been reinstalled or AC power has been restored to the power supply. The HSV110 controller is identified in the handle field. The secondaryId field contains the '2' blower/power supply assembly internal identifier value: 2. The value.ul1 field contains the new state of the Blower/Power Supply Present flag: 1 (PRESENT). The value.ul2 field contains the old state of the Blower/Power Supply Present flag: 0 (NOT PRESENT). | ||
| NTF sCellEventTrap92a | 1.3.6.1.4.1.232.0.13602346 | Severity: Critical -- failure or failure imminent. The '1' blower/power supply located within the HSV110 controller identified in the handle field is running slower than the lowest acceptable speed. The secondaryId field contains the '1' blower/power supply assembly internal identifier value: 1. The value.ul1 field contains the current speed of the '1' blower/power supply. The value.ul2 field contains the lowest acceptable speed for the '1' blower/power supply. | ||
| NTF sCellEventTrap92b | 1.3.6.1.4.1.232.0.13602347 | Severity: Critical -- failure or failure imminent. The '2' blower/power supply located within the HSV110 controller identified in the handle field is running slower than the lowest acceptable speed. The secondaryId field contains the '2' blower/power supply assembly internal identifier value: 2. The value.ul1 field contains the current speed of the '2' blower/power supply. The value.ul2 field contains the lowest acceptable speed for the '2' blower/power supply. | ||
| NTF sCellEventTrap92c | 1.3.6.1.4.1.232.0.13602348 | Severity: Warning -- not failed but attention recommended or required. The state of a battery assembly within the HSV110 controller identified in the handle field has transitioned to the Battery System Hold-up Time is zero hours state. The value.ul1 field contains the new state 5: (Battery System Hold-up Time is zero hours). The value.ul2 field contains the old state. The state values that may be found in the value.ul2 field are as follows: 1 = Battery System Hold-up Time is greater than 96 hours 3 = Battery System Hold-up Time is greater than 0 and less than 96 hours 5 = Battery System Hold-up Time is zero hours | ||
| NTF sCellEventTrap92d | 1.3.6.1.4.1.232.0.13602349 | Severity: Undetermined -- more information needed to determine severity. The Resource Availability state of a Volume has transitioned to the INSUFFICIENT state. The affected Volume is identified in the handle field. The addHandle field contains the identity of the Physical Disk Drive that is associated with that Volume. The enclosure number, bay number, and rack number where the associated Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], and attribute.value.u32[2] fields, respectively. The internal identification of that Volume's Redundant Storage Set is contained in the attribute.value.u32[3] field. The attribute.type field contains the value of 1. The value.ul1 field contains the new state: 1 (INSUFFICIENT). The value.ul2 field contains the old state: 0 (SUFFICIENT). | ||
| NTF sCellEventTrap92e | 1.3.6.1.4.1.232.0.13602350 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field rejected a login attempt. The value.ul1 and value.ul2 fields contain words [0] and [1], respectively, of the World Wide Name of the host adapter that originated the rejected login attempt. The secondaryId field contains the reason for the rejection as follows: 50 = The host is already logged in 101 = Maximum number of logins is exceeded 102 = Invalid cookie was sent 106 = The password is not set on the HSV110 controller | ||
| NTF sCellEventTrap92f | 1.3.6.1.4.1.232.0.13602351 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field processed a Storage System Management Interface command with the result of non-success return code. The value.ul1 field contains internal the command type. The value.ul2 field contains the internal return code. The attribute.value.obj field contains the internal target and internal version of the command. | ||
| NTF sCellEventTrap930 | 1.3.6.1.4.1.232.0.13602352 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field has updated the physical disk drive map for the loop pair identified in the secondaryId field. The value.ul1 field contains the new internal map generation number. The value.ul2 field contains the old internal map generation number. | ||
| NTF sCellEventTrap931 | 1.3.6.1.4.1.232.0.13602353 | Severity: Critical -- failure or failure imminent. The state of the Physical Disk Drive identified in the handle field has transitioned to the DEGRADED state. The value.ul1 field contains the new state: 2 (DEGRADED). The value.ul2 field contains the old state. The state values that may be in the value.ul2 field are as follows: 1 = Normal 3 = Failed 4 = Not present 5 = Single Port on Fibre The enclosure number, bay number, and rack number where the Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], attribute.value.u32[2] fields, respectively. The attribute.type field contains value 1. The rack number in the attribute.value.u32[2] field will not contain a valid value until a future release. | ||
| NTF sCellEventTrap932 | 1.3.6.1.4.1.232.0.13602354 | Severity: Critical -- failure or failure imminent. The state of the Physical Disk Drive identified in the handle field has transitioned to the FAILED state. The value.ul1 field contains the new state: 3 (FAILED). The value.ul2 field contains the old state. The state values that may be in the value.ul2 field are as follows: 1 = Normal 2 = Degraded 4 = Not present 5 = Single Port on Fibre The enclosure number, bay number, and rack number where the Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], attribute.value.u32[2] fields, respectively. The attribute.type field contains value 1. The rack number in the attribute.value.u32[2] field will not contain a valid value until a future release. | ||
| NTF sCellEventTrap933 | 1.3.6.1.4.1.232.0.13602355 | Severity: Normal -- informational in nature. The Derived Unit identified in the handle field was created. The addHandle field contains the identity of the Storage System Virtual Disk that is associated with that Derived Unit. The attribute.value.obj field contains the identity of the Virtual Disk associated with that Derived Unit. | ||
| NTF sCellEventTrap934 | 1.3.6.1.4.1.232.0.13602356 | Severity: Normal -- informational in nature. The internal Logical Disk associated with the Virtual Disk identified in the handle field was created. The addHandle field contains the identity of the Disk Group where this internal Logical Disk was created. The attribute.value.u64[0] field contains the size (in blocks) of the internal Logical Disk. The attribute.value.u32[2] field contains the redundancy type of the internal Logical Disk. The attribute.type field contains the value 5. The values that may be found in the attribute.value.u32[2] field are as follows: 1 = Vraid0 2 = Vraid1 3 = Vraid5 | ||
| NTF sCellEventTrap935 | 1.3.6.1.4.1.232.0.13602357 | Severity: Normal -- informational in nature. The Disk Group identified in the handle field was created. The attribute.value.u32[0] field contains the number of physical disk drives within the Disk Group. The attribute.type field contains the value 1. | ||
| NTF sCellEventTrap936 | 1.3.6.1.4.1.232.0.13602358 | Severity: Normal -- informational in nature. The Physical Disk Drive identified in the handle field was discovered. The enclosure, bay and rack where the Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1] and attribute.value.u32[2] fields, respectively. The attribute.type field contains the value 1. | ||
| NTF sCellEventTrap937 | 1.3.6.1.4.1.232.0.13602359 | Severity: Normal -- informational in nature. The Presented Unit identified in the handle field was created. The addHandle field contains the identity of the Storage System Virtual Disk that is associated with the Presented Unit. This Presented Unit is associated with the Virtual Disk identified in the attribute.value.obj.handle field. The addHandle2 field contains the associated Storage System Host path, and addData[0] and addData[1] contains the host LUN number. | ||
| NTF sCellEventTrap938 | 1.3.6.1.4.1.232.0.13602360 | Severity: Normal -- informational in nature. The Storage System Host path identified in the handle field was created. | ||
| NTF sCellEventTrap939 | 1.3.6.1.4.1.232.0.13602361 | Severity: Normal -- informational in nature. The Storage System Virtual Disk identified in the handle field was created. | ||
| NTF sCellEventTrap93a | 1.3.6.1.4.1.232.0.13602362 | Severity: Normal -- informational in nature. A Volume was created. The Volume is identified in the handle field. The addHandle field contains the identity of the Physical Disk Drive that is associated with that Volume. The enclosure number, bay number, and rack number where the associated Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], and attribute.value.u32[2] fields, respectively. The attribute.type field contains the value of 1. | ||
| NTF sCellEventTrap93b | 1.3.6.1.4.1.232.0.13602363 | Severity: Normal -- informational in nature. The Derived Unit identified in the handle field was deleted. The addHandle field contains the identity of the Storage System Virtual Disk that was associated with the Derived Unit. This Derived Unit is associated with the Virtual Disk identified in the attribute.value.obj.handle field. | ||
| NTF sCellEventTrap93c | 1.3.6.1.4.1.232.0.13602364 | Severity: Normal -- informational in nature. The internal Logical Disk associated with the Virtual Disk identified in the handle field was deleted. | ||
| NTF sCellEventTrap93d | 1.3.6.1.4.1.232.0.13602365 | Severity: Normal -- informational in nature. The Disk Group identified in the handle field was deleted. | ||
| NTF sCellEventTrap93e | 1.3.6.1.4.1.232.0.13602366 | Severity: Critical -- failure or failure imminent. The Physical Disk Drive identified in the handle field has disappeared. The enclosure, bay and rack where the Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1] and attribute.value.u32[2] fields, respectively. The attribute.type field contains the value 1. | ||
| NTF sCellEventTrap93f | 1.3.6.1.4.1.232.0.13602367 | Severity: Normal -- informational in nature. The Presented Unit identified in the handle field was deleted. The addHandle field contains the identity of the Storage System Virtual Disk that was associated with the Presented Unit. This Presented Unit is associated with the Virtual Disk identified in the attribute.value.obj.handle field. | ||
| NTF sCellEventTrap940 | 1.3.6.1.4.1.232.0.13602368 | Severity: Normal -- informational in nature. The Storage System Host path identified in the handle field was deleted. | ||
| NTF sCellEventTrap941 | 1.3.6.1.4.1.232.0.13602369 | Severity: Normal -- informational in nature. The Storage System Virtual Disk identified in the handle field was deleted. The Storage System Virtual Disk is associated with the Virtual Disk identified in the addHandle field. | ||
| NTF sCellEventTrap943 | 1.3.6.1.4.1.232.0.13602371 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field has joined the Storage System. If the handle field is zero, the HSV110 controller identity could not be obtained due to an unexpected state transition. | ||
| NTF sCellEventTrap944 | 1.3.6.1.4.1.232.0.13602372 | Severity: Undetermined -- more information needed to determine severity. An HSV110 controller has left the Storage System. The HSV110 controller is identified in the handle field. If the handle field is zero, the HSV110 controller identity could not be obtained due to an unexpected state transition. | ||
| NTF sCellEventTrap945 | 1.3.6.1.4.1.232.0.13602373 | Severity: Normal -- informational in nature. A Storage System has been deleted by an HSV110 controller. The Storage System is identified in the handle field. The HSV110 controller is identified in the addHandle field. If the handle field or addHandle field is zero, the corresponding identity could not be obtained due to an unexpected state transition. | ||
| NTF sCellEventTrap946 | 1.3.6.1.4.1.232.0.13602374 | Severity: Normal -- informational in nature. The Data Replication Group identified in the handle field was created. | ||
| NTF sCellEventTrap947 | 1.3.6.1.4.1.232.0.13602375 | Severity: Normal -- informational in nature. The Data Replication Group identified in the handle field was deleted. | ||
| NTF sCellEventTrap948 | 1.3.6.1.4.1.232.0.13602376 | Severity: Normal -- informational in nature. The internal Logical Disk associated with the Snapshot Virtual Disk identified in the handle field was created. The addHandle field contains the identity of the Disk Group where this internal Logical Disk was created. The attribute.value.u64[0] field contains the size (in blocks) of the reserved capacity of the internal Logical Disk. The attribute.value.u32[2] field contains the redundancy type of the internal Logical Disk. The attribute.value.u32[3] field contains the noid of the associated successor internal Logical Disk. The attribute.type field contains the value 6. The values that may be found in the attribute.value.u32[2] field are as follows: 1 = Vraid0 2 = Vraid1 3 = Vraid5 | ||
| NTF sCellEventTrap949 | 1.3.6.1.4.1.232.0.13602377 | Severity: Normal -- informational in nature. The internal Logical Disk associated with the Copy of the Virtual Disk identified in the handle field was created. The addHandle field contains the identity of the Disk Group where this internal Logical Disk was created. The attribute.value.u64[0] field contains the size (in blocks) of the reserved capacity of the target Virtual Disk. The attribute.value.u32[2] field contains the redundancy type of the internal Logical Disk. The attribute.value.u32[3] field contains the noid of the associated successor internal Logical Disk. The attribute.type field contains the value 6. The values that may be found in the attribute.value.u32[2] field are as follows: 1 = Vraid0 2 = Vraid1 3 = Vraid5 | ||
| NTF sCellEventTrap965 | 1.3.6.1.4.1.232.0.13602405 | Severity: Normal -- informational in nature. The Host Operating System mode of the Storage System Host identified in the handle field has changed. The oldAttr.type and newAttr.type fields contain the value 1. The oldAttr.value.u32[0] field contains the old Host Operating System mode. The newAttr.value.u32[0] field contains the new Host Operating System mode. The values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 0 = Unknown 1 = User defined 2 = Unused 3 = WINNT with SecurePath 4 = VMS 5 = TRU64 UNIX 6 = Sun UNIX 7 = NetWare 8 = HP 9 = IBM 10 = LINUX 11 = SCO UNIX | ||
| NTF sCellEventTrap966 | 1.3.6.1.4.1.232.0.13602406 | Severity: Normal -- informational in nature. Time was set on the Storage System identified in the handle field. | ||
| NTF sCellEventTrap967 | 1.3.6.1.4.1.232.0.13602407 | Severity: Normal -- informational in nature. The LUN of the Presented Unit identified in the handle field has changed. The oldAttr.type field and the newAttr.type fields contain the value 1. The oldAttr.value.u32[0..1] fields contain the value of the old LUN. The newAttr.value.u32[0..1] fields contain the value of the new LUN. The secondaryId field contains the noid portion of the handle for the Storage System Virtual Disk associated with the Presented Unit. This Presented Unit is associated with the Virtual Disk identified in the addHandle field. | ||
| NTF sCellEventTrap968 | 1.3.6.1.4.1.232.0.13602408 | Severity: Normal -- informational in nature. The Device Addition Policy of the Storage System identified in the handle field has changed. The oldAttr.type field and the newAttr.type fields contain the value 1. The oldAttr.value.u32[0] field contains the old Device Addition Policy. The newAttr.value.u32[0] field contains the new Device Addition Policy. The policy values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 1 = Manual policy 2 = Automatic policy | ||
| NTF sCellEventTrap969 | 1.3.6.1.4.1.232.0.13602409 | Severity: Normal -- informational in nature. The Quiescent state of the Storage System Virtual Disk identified in the handle field has changed. The oldAttr.type field and the newAttr.type fields contain the value 1. The oldAttr.value.u32[0] field contains the old Quiescent state. The newAttr.value.u32[0] field contains the new Quiescent state. The state values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 0 = Not quiescent 1 = Quiescent This Storage System Virtual Disk is associated with the Virtual Disk identified in the addHandle field. | ||
| NTF sCellEventTrap96a | 1.3.6.1.4.1.232.0.13602410 | Severity: Normal -- informational in nature. The Enabled/Disabled state of the Storage System Virtual Disk identified in the handle field has changed. The oldAttr.type field and the newAttr.type fields contain the value 1. The oldAttr.value.u32[0] field contains the old Enabled/Disabled state. The newAttr.value.u32[0] field contains the new Enabled/Disabled state. The state values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 1 = Disabled 2 = Enabled This Storage System Virtual Disk is associated with the Virtual Disk identified in the addHandle field. | ||
| NTF sCellEventTrap96b | 1.3.6.1.4.1.232.0.13602411 | Severity: Normal -- informational in nature. The Cache Policy of the Storage System Virtual Disk identified in the handle field has changed. The oldAttr.type field and the newAttr.type fields contain the value 1. The oldAttr.value.u32[0] field contains the old Write Cache Policy. The newAttr.value.u32[0] field contains the new Write Cache Policy. The policy values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 1 = Writethrough 2 = Writeback The oldAttr.value.u32[1] field contains the old Read Cache Policy. The newAttr.value.u32[1] field contains the new Read Cache Policy. The policy values that may be found in the oldAttr.value.u32[1] and newAttr.value.u32[1] fields are as follows: 1 = Read cache on 2 = Read cache off The oldAttr.value.u32[2] field contains the old Cache Mirroring Policy. The newAttr.value.u32[2] field contains the new Cache Mirroring Policy. The policy values that may be found in the oldAttr.value.u32[2] and newAttr.value.u32[2] fields are as follows: 1 = Mirror 2 = No mirror This Storage System Virtual Disk is associated with the Virtual Disk identified in the addHandle field. | ||
| NTF sCellEventTrap96c | 1.3.6.1.4.1.232.0.13602412 | Severity: Normal -- informational in nature. The Usage state of a Volume changed. The affected Volume is identified in the handle field. The oldAttr.value.u32[0] field contains the old Usage state. The newAttr.value.u32[0] field contains the new Usage state. The Usage state values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 1 = Disk Group 2 = Reserved 4 - 20 = temporary usage reserved for drive code load This Volume is associated with the Disk Group identified in the addHandle field, if either the old Usage state or the new Usage state is 1. The secondaryId field contains the internal identification of that Volume's Redundant Storage Set. | ||
| NTF sCellEventTrap96d | 1.3.6.1.4.1.232.0.13602413 | Severity: Normal -- informational in nature. The Disk Failure Protection Level of the Disk Group identified in the handle field has changed. The oldAttr.type and newAttr.type fields contain the value 1. The oldAttr.value.u32[0] field contains the old number of physical disk drives available for use. The newAttr.value.u32[0] field contains the new number of physical disk drives available for use. | ||
| NTF sCellEventTrap96e | 1.3.6.1.4.1.232.0.13602414 | Severity: Normal -- informational in nature. The Write Protected state of the Derived Unit identified in the handle field has changed. This Derived Unit is associated with the Virtual Disk identified in the addHandle field. The secondaryId field contains the noid portion of the handle for the Storage System Virtual Disk associated with the Derived Unit. The oldAttr.type field and the newAttr.type fields contain the value 1. The oldAttr.value.u32[0] field contains the old Write Protected state. The newAttr.value.u32[0] field contains the new Write Protected state. The Write Protected state values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 0 = Write protect off 1 = Write protect on This Derived Unit is associated with the Virtual Disk identified in the addHandle field. | ||
| NTF sCellEventTrap970 | 1.3.6.1.4.1.232.0.13602416 | Severity: Warning -- not failed but attention recommended or required. The Physical Disk Drive identified in the handle field has experienced numerous communication failures on a particular Fibre Channel port identified in the newAttr.value.str field. The oldAttr.value.u32[0] field contains the internal port ID. The enclosure number, bay number, and rack number where the Physical Disk Drive is located are contained in the oldAttr.value.u32[1], oldAttr.value.u32[2], oldAttr.value.u32[3] fields, respectively. The oldAttr.type field contains value 1. The newAttr.value.str field contains the cerpId of the Fibre Channel port. The newAttr.type field contains value 4. | ||
| NTF sCellEventTrap971 | 1.3.6.1.4.1.232.0.13602417 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field received a request to shutdown. The oldAttr.type field and field contain the value 1. The oldAttr.value.u32[0] field indicates the type of restart that was requested as follows: 0 = None -- no restart 1 = Regular -- full restart, host system connectivity is lost until the controller returns to normal operation 2 = Fast -- resynchronization, restart of the controller in a manner that has little or no impact on host system connectivity The oldAttr.value.u32[1] field indicates whether the other HSV110 controller of the pair was requested to remain operational or to also shutdown as follows: 0 = Remain operational 1 = Coupled shutdown The oldAttr.value.u32[2] field indicates whether the HSV110 controller was requested to remain in the power on state or power itself off as follows: 0 = Remain in the power on state 1 = Power itself off The oldAttr.value.u32[3] field value indicates whether the Physical Disk Drive enclosure(s) was requested to remain in the power on state or to be powered off as follows: 0 = Remain in the power on state 1 = Powered off The oldAttr.value.u32[4] field value indicates whether the battery assemblies located within the HSV110 controller were requested to be enabled or disabled as follows: 0 = Enabled 1 = Disabled The oldAttr.value.u32[5] field contains the number of seconds the shutdown operation was requested to be delayed. | ||
| NTF sCellEventTrap972 | 1.3.6.1.4.1.232.0.13602418 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field has completed its shutdown preparations. The oldAttr.type field contain the value 1. The oldAttr.value.u32[0] field value indicates the result of the HSV110 controller Cache Memory shutdown operation as follows: 1 = Success 2 = Failure 3 = Not applicable The oldAttr.value.u32[1] field contains the internal Storage System Management Interface cache shutdown status code. The oldAttr.value.u32[2] field value indicates the result of the Physical Disk Drive enclosure(s) power off operation as follows: 1 = Success 2 = Failure 3 = Not applicable The oldAttr.value.u32[3] field contains the internal Storage System Management Interface Physical Disk Drive enclosure(s) power off status code. The oldAttr.value.u32[4] field value indicates the result of the battery assemblies disable operation as follows: 1 = Success 2 = Failure 3 = Not applicable The oldAttr.value.u32[5] field value indicates the battery assemblies disable operation failure mode as follows: 0 = No failure indicated. 1 = Failed only on the HSV110 controller identified in the handle field. 2 = Failed only on the other HSV110 controller of the pair. 3 = Failed on both HSV110 controllers. | ||
| NTF sCellEventTrap973 | 1.3.6.1.4.1.232.0.13602419 | Severity: Normal -- informational in nature. The Failsafe state of the Data Replication Group identified in the handle field has changed. The oldAttr.value.u32[0] field contains the old Failsafe state. The newAttr.value.u32[0] field contains the new Failsafe state. The Failsafe state values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 1 = Failsafe Disabled 2 = Failsafe Enabled | ||
| NTF sCellEventTrap974 | 1.3.6.1.4.1.232.0.13602420 | Severity: Normal -- informational in nature. The Mode of the Data Replication Group identified in the handle field has changed. The oldAttr.value.u32[0] field contains the old Mode. The newAttr.value.u32[0] field contains the new Mode. The Mode values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 0 = Normal Active Source 1 = Normal Active Destination 2 = Active/Active (Master) 3 = Active/Active (Non-Master) | ||
| NTF sCellEventTrap975 | 1.3.6.1.4.1.232.0.13602421 | Severity: Normal -- informational in nature. The Operational state of a Data Replication Group has changed to Synchronous or Asynchronous. The oldAttr.value.u32[0] field contains the old Operation state. The newAttr.value.u32[0] field contains the new Operation state. The Operation state values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 1 = Synchronous 2 = Asynchronous | ||
| NTF sCellEventTrap976 | 1.3.6.1.4.1.232.0.13602422 | Severity: Normal -- informational in nature. The Read Only attribute of the Data Replication Group identified in the handle field has changed. The oldAttr.value.u32[0] field contains the old Read Only attribute. The newAttr.value.u32[0] field contains the new Read Only attribute. The Read Only attribute values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 0 = Data Replication Destination Storage System Virtual Disk disabled for read access. 1 = Data Replication Destination Storage System Virtual Disk enabled for read access. | ||
| NTF sCellEventTrap977 | 1.3.6.1.4.1.232.0.13602423 | Severity: Normal -- informational in nature. A Data Replication Group failover has occurred. The handle field contains the identity of the Data Replication Group. The oldAttr.value.u32[0] field contains the old Role. The newAttr.value.u32[0] field contains the new Role. 0 = Normal Active Source 1 = Normal Active Destination 2 = Active/Active (Master) 3 = Active/Active (Non-Master) | ||
| NTF sCellEventTrap978 | 1.3.6.1.4.1.232.0.13602424 | Severity: Normal -- informational in nature. A Data Replication Group has been suspended or resumed. The handle field contains the identity of the Data Replication Group. The oldAttr.value.u32[0] field contains the old Suspend state. The newAttr.value.u32[0] field contains the new Suspend state. The Suspend state values that may be found in the oldAttr.value.u32[0] and newAttr.value.u32[0] fields are as follows: 1 = Connection between the Data Replication Source and Data Replication Destination is active. 2 = Connection between the Data Replication Source and Data Replication Destination is inactive. | ||
| NTF sCellEventTrap979 | 1.3.6.1.4.1.232.0.13602425 | Severity: Normal -- informational in nature. A Storage System Virtual Disk was added to a Data Replication Group. The Storage System Virtual Disk is identified in the addHandle field. The Data Replication Group is identified in the handle field. | ||
| NTF sCellEventTrap97a | 1.3.6.1.4.1.232.0.13602426 | Severity: Normal -- informational in nature. A Storage System Virtual Disk was removed from a Data Replication Group. The Storage System Virtual Disk is identified in the addHandle field. The Data Replication Group is identified in the handle field. | ||
| NTF sCellEventTrap9C8 | 1.3.6.1.4.1.232.0.13602504 | Severity: Undetermined -- more information needed to determine severity. The Data Availability state of the internal Logical Disk associated with the Virtual Disk identified in the handle field has transitioned to the DATA LOST state. The value.ul1 field contains the new state: 1 (DATA LOST). The value.ul2 field contains the old state: 0 (NORMAL). | ||
| NTF sCellEventTrap9C9 | 1.3.6.1.4.1.232.0.13602505 | Severity: Undetermined -- more information needed to determine severity. The state of the Disk Group identified in the handle field has transitioned to an INOPERATIVE state. The value.ul1 field contains the new Disk Group state. The value.ul2 field contains the old Disk Group state. The state values that may be found in the value.ul1 and value.ul2 fields are as follows: 1 = Normal 2 = Disk Group with no redundancy is inoperative 3 = Disk Group with parity redundancy is inoperative 4 = Disk Group with mirrored redundancy is inoperative 5 = Disk Group with no redundancy is inoperative, marked for re-use 6 = Disk Group with parity redundancy is inoperative, marked for re-use 7 = Disk Group with mirrored redundancy is inoperative, marked for re-use | ||
| NTF sCellEventTrap9Ca | 1.3.6.1.4.1.232.0.13602506 | Severity: Undetermined -- more information needed to determine severity. The state of the internal Logical Disk associated with the Virtual Disk identified in the handle field has transitioned to the FAILED state. The value.ul1 field contains the new state: 5 (FAILED). The value.ul2 field contains the old state. The state values that may be found in the value.ul2 field are as follows: 1 = Normal 2 = Replacement delay in progress 3 = Redundancy lost, restore in progress 4 = Redundancy lost, restore stalled 6 = Creation in progress 7 = Snapshot is inoperative due to lack of snapshot space 8 = Deletion in progress 9 = Capacity change in progress 10 = Inoperative due to data lost 11 = Capacity reservation in progress 12 = Capacity unreservation in progress | ||
| NTF sCellEventTrap9Cb | 1.3.6.1.4.1.232.0.13602507 | Severity: Critical -- failure or failure imminent. The state of the internal Logical Disk associated with the Virtual Disk identified in the handle field has transitioned to the SNAPSHOT OVERCOMMIT state. The value.ul1 field contains the new state: 7 (SNAPSHOT OVERCOMMIT). The value.ul2 field contains the old state. The state values that may be found in the value.ul2 field are as follows: 1 = Normal 2 = Replacement delay in progress 3 = Redundancy lost, restore in progress 4 = Redundancy lost, restore stalled 5 = Failed 6 = Creation in progress 8 = Deletion in progress 9 = Capacity change in progress 10 = Inoperative due to device data lost 11 = Capacity reservation in progress 12 = Capacity unreservation in progress | ||
| NTF sCellEventTrap9Cc | 1.3.6.1.4.1.232.0.13602508 | Severity: Undetermined -- more information needed to determine severity. The state of the internal Logical Disk associated with the Virtual Disk identified in the handle field has transitioned to the DEVICE DATA LOST state. The value.ul1 field contains the new state: 10 (DEVICE DATA LOST). The value.ul2 field contains the old state. The state values that may be found in the value.ul2 field are as follows: 1 = Normal 2 = Replacement delay in progress 3 = Redundancy lost restore, in progress 4 = Redundancy lost restore, stalled 5 = Failed 6 = Creation in progress 7 = Snapshot is inoperative due to lack of snapshot space 8 = Deletion in progress 9 = Capacity change in progress 11 = Capacity reservation in progress 12 = Capacity unreservation in progress | ||
| NTF sCellEventTrap9Cd | 1.3.6.1.4.1.232.0.13602509 | Severity: Undetermined -- more information needed to determine severity. The state of the Fibre Channel port identified in the attribute.value.str field and located on the rear panel of the HSV110 controller identified in the handle field has transitioned to the FAILED state. The attribute.type field contains the value 4. The value.ul1 field contains the new state: 2 (FAILED). The value.ul2 field contains the old state: 1 (NORMAL). Note that the HSV110 controller's internal identity of the affected Fibre Channel port is contained in the secondaryId field. | ||
| NTF sCellEventTrap9Ce | 1.3.6.1.4.1.232.0.13602510 | Severity: Normal -- informational in nature. The state of the Disk Group identified in the handle field has transitioned to an INOPERATIVE MARKED state. The value.ul1 field contains the new Disk Group state. The value.ul2 field contains the old Disk Group state. The state values that may be found in the value.ul1 and value.ul2 fields are as follows: 1 = Normal 2 = Disk Group with no redundancy is inoperative 3 = Disk Group with parity redundancy is inoperative 4 = Disk Group with mirrored redundancy is inoperative 5 = Disk Group with no redundancy is inoperative, marked for re-use 6 = Disk Group with parity redundancy is inoperative, marked for re-use 7 = Disk Group with mirrored redundancy is inoperative, marked for re-use | ||
| NTF sCellEventTrap9Cf | 1.3.6.1.4.1.232.0.13602511 | Severity: Warning -- not failed but attention recommended or required. The state of the Physical Disk Drive identified in the handle field has transitioned to the NOT PRESENT state. The value.ul1 field contains the new state: 4 (NOT PRESENT). The value.ul2 field contains the old state. The state values that may be in the value.ul2 field are as follows: 1 = Normal 2 = Degraded 3 = Failed 5 = Single Port on Fibre The enclosure number, bay number, and rack number where the Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], attribute.value.u32[2] fields, respectively. The attribute.type field contains value 1. The rack number in the attribute.value.u32[2] field will not contain a valid value until a future release. | ||
| NTF sCellEventTrap9D0 | 1.3.6.1.4.1.232.0.13602512 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field no longer needs attention. | ||
| NTF sCellEventTrap9D1 | 1.3.6.1.4.1.232.0.13602513 | Severity: Undetermined -- more information needed to determine severity. The HSV110 controller identified in the handle field needs attention. | ||
| NTF sCellEventTrap9D2 | 1.3.6.1.4.1.232.0.13602514 | Severity: Critical -- failure or failure imminent. The Blower Present flag for the '1' blower assembly located within the HSV110 controller identified in the handle field has transitioned from the PRESENT to NOT PRESENT state indicating that the blower has been removed. The secondaryId field contains the '1' blower assembly internal identifier value: 1. The value.ul1 field contains the new state of the Blower Present flag: 0 (NOT PRESENT). The value.ul2 field contains the old state of the Blower Present flag: 1 (PRESENT). | ||
| NTF sCellEventTrap9D3 | 1.3.6.1.4.1.232.0.13602515 | Severity: Undetermined -- more information needed to determine severity. At least one Virtual Disk associated with the Data Replication Group identified in the handle field has transitioned to the INOPERATIVE state. The remaining Virtual Disks associated with this Data Replication Group have been forced INOPERATIVE. The value.ul1 field contains the new Data Replication Group member state: 2 (INOPERATIVE). The value.ul2 field contains the old Data Replication Group member state: 1 (OPERATIVE). | ||
| NTF sCellEventTrap9D4 | 1.3.6.1.4.1.232.0.13602516 | Severity: Normal -- informational in nature. All the Virtual Disks associated with the Data Replication Group identified in the handle field have transitioned to the OPERATIVE state. The value.ul1 field contains the new Data Replication Group member state: 1 (OPERATIVE). The value.ul2 field contains the old Data Replication Group member state: 2 (INOPERATIVE). | ||
| NTF sCellEventTrap9D5 | 1.3.6.1.4.1.232.0.13602517 | Severity: Normal -- informational in nature. The state of the Physical Disk Drive identified in the handle field has transitioned to the Single Port on Fibre state. The value.ul1 field contains the new state: 5 (SINGLE PORT ON FIBRE). The value.ul2 field contains the old state. The state values that may be in the value.ul2 field are as follows: 1 = Normal 2 = Degraded 3 = Failed 4 = Not Present The enclosure number, bay number, and rack number where the Physical Disk Drive is located are contained in the attribute.value.u32[0], attribute.value.u32[1], attribute.value.u32[2] fields, respectively. The attribute.type field contains value 1. The rack number in the attribute.value.u32[2] field will not contain a valid value until a future release. | ||
| NTF sCellEventTrap9D6 | 1.3.6.1.4.1.232.0.13602518 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field has been shutdown because the temperature sensors do not agree and the system temperature can not be accurately determined. The value.ul1 field contains the current temperature reported in celsius from I2C sensor 1, while the value.ul2 field contains the reading from I2C sensor 2. | ||
| NTF sCellEventTrap9D7 | 1.3.6.1.4.1.232.0.13602519 | Severity: Normal -- informational in nature. The HSV110 controller identified in the handle field has been shutdown because the temperature sensors can not be accessed and the system temperature can not be accurately determined. The value.ul1 field contains the status from the attempted I2C access. | ||
| NTF sCellEventTrapB0 | 1.3.6.1.4.1.232.0.13602816 | Severity: Normal -- informational in nature. The HSV110 controller identified by the nodeName field has begun a resynchronization operation (i.e., a restart of the controllers in a manner that has little or no impact on host system connectivity). The information.pc field contains the program counter of resynchronization operation initiator. The information.flags field contains reboot flags value. The information.code field contains the resynchronization operation event code value. | ||
| NTF sCellEventTrapC0 | 1.3.6.1.4.1.232.0.13603072 | Severity: Normal -- informational in nature. The specified Destination Virtual Disk has successfully completed a Full Copy. The following fields are not valid: status, blocks, vda. | ||
| NTF sCellEventTrapC1 | 1.3.6.1.4.1.232.0.13603073 | Severity: Critical -- failure or failure imminent. The specified Source Virtual Disk has transitioned to the Logging state because the alternate Storage System is not accessible or the Data Replication Group is suspended. The following fields are not valid: status, blocks, vda, port, cerpId, side. | ||
| NTF sCellEventTrapC2 | 1.3.6.1.4.1.232.0.13603074 | Severity: Critical -- failure or failure imminent. The specified Source Virtual Disk has transitioned to the Logging state because the Destination Virtual Disk is not accessible. The following fields are not valid: status, blocks, vda, port, cerpId, side. | ||
| NTF sCellEventTrapC3 | 1.3.6.1.4.1.232.0.13603075 | Severity: Normal -- informational in nature. The specified Destination Virtual Disk has transitioned to the Merging state, because the alternate Storage System or Destination Virtual Disk is now accessible or resumed. The following fields are not valid: status, blocks, vda. | ||
| NTF sCellEventTrapC4 | 1.3.6.1.4.1.232.0.13603076 | Severity: Critical -- failure or failure imminent. A Data Replication Group has entered the Failsafe Locked state due to an inaccessible or inoperative destination. Either the Destination Virtual Disk is not accessible or a Virtual Disk in the Data Replication Group is inoperative. The following fields are not valid: status, blocks, vda, port, cerpId, side. | ||
| NTF sCellEventTrapC5 | 1.3.6.1.4.1.232.0.13603077 | Severity: Critical -- failure or failure imminent. A Data Replication Group has entered the Failsafe Locked state due to an inoperative source. Either the Source Virtual Disk is not accessible or a Virtual Disk in the Data Replication Group is inoperative. The following fields are not valid: status, blocks, vda, port, cerpId, side. | ||
| NTF sCellEventTrapC6 | 1.3.6.1.4.1.232.0.13603078 | Severity: Critical -- failure or failure imminent. An unrecoverable read error occurred on the specified Source Virtual Disk during the Full Copy. The Virtual Disk address specified in the vda field indicates the first block in error. The Full Copy was terminated. | ||
| NTF sCellEventTrapC7 | 1.3.6.1.4.1.232.0.13603079 | Severity: Critical -- failure or failure imminent. A Full Copy terminated prior to completion. A remote copy error occurred due to an inaccessible alternate Storage System. The Virtual Disk address specified in the vda field indicates the first block in error. The Full Copy will continue when the Data Replication Destination is restored. | ||
| NTF sCellEventTrapC8 | 1.3.6.1.4.1.232.0.13603080 | Severity: Critical -- failure or failure imminent. A Full Copy terminated prior to completion. A remote copy error occurred due to an inaccessible Destination Virtual Disk. The Virtual Disk address specified in the vda field indicates the first block in error. The Full Copy will continue when the Data Replication Destination is restored. | ||
| NTF sCellEventTrapC9 | 1.3.6.1.4.1.232.0.13603081 | Severity: Warning -- not failed but attention recommended or required. A Data Replication Log has been reset due to insufficient Disk Group capacity. The Data Replication Destination has been marked for a Full Copy. The following fields are not valid: status, blocks, vda, port, cerpId, side. | ||
| NTF sCellEventTrapCA | 1.3.6.1.4.1.232.0.13603082 | Severity: Normal -- informational in nature. A Data Replication Log has been reset due to a Data Replication Group failover. The following fields are not valid: status, blocks, vda. | ||
| NTF sCellEventTrapCC | 1.3.6.1.4.1.232.0.13603084 | Severity: Normal -- informational in nature. A Destination Data Replication Group has successfully completed a Merge. The following fields are not valid: status, blocks, vda. | ||
| NTF sCellEventTrapCF | 1.3.6.1.4.1.232.0.13603087 | Severity: Normal -- informational in nature. A Data Replication Group is no longer in a Failsafe Locked state. The following fields are not valid: status, blocks, vda, port, cerpId, side. | ||
| NTF sCellEventTrapC10 | 1.3.6.1.4.1.232.0.13603088 | Severity: Normal -- informational in nature. A Destination Data Replication Group has been marked for a Full Copy. The following fields are not valid: status, blocks, vda. | ||
| NTF sCellEventTrapC11 | 1.3.6.1.4.1.232.0.13603089 | Severity: Normal -- informational in nature. A Storage System has discovered that a Data Replication Group failover has taken place. This Virtual Disk is transitioning from a Data Replication Source role to a Data Replication Destination role. The following fields are not valid: status, blocks, vda. | ||
| NTF sCellEventTrapC12 | 1.3.6.1.4.1.232.0.13603090 | Severity: Normal -- informational in nature. This Data Replication Group is transitioning from a Data Replication Destination role to a Data Replication Source role. The following fields are not valid: status, blocks, vda. | ||
| NTF sCellEventTrapC15 | 1.3.6.1.4.1.232.0.13603093 | Severity: Normal -- informational in nature. The Data Replication Path between this Site and the Alternate Site has closed, possibly due to a connection failure between the specified host port and the Alternate Site. The following fields are not valid: groupNameUuid, groupUuid, sourceScvdUuid, status, block, vda. | ||
| NTF sCellEventTrapD0 | 1.3.6.1.4.1.232.0.13603328 | Severity: Critical -- failure or failure imminent. Unrecognized event reported by a Drive Enclosure Environmental Monitoring Unit. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. The event was reported by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The content of the alarmErrorCode field could not be translated into a known event. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD1 | 1.3.6.1.4.1.232.0.13603329 | Severity: Critical -- failure or failure imminent. A physical disk drive that is not Fibre Channel compatible or cannot operate at the link rate established by the drive enclosure I/O modules was detected. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. This problem was detected during spin up of the physical disk drive installed in the drive enclosure bay identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD2 | 1.3.6.1.4.1.232.0.13603330 | Severity: Warning -- not failed but attention recommended or required. A physical disk drive is improperly installed or missing. This could affect the drive enclosure air flow and cause an over temperature condition. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The affected drive enclosure bay is identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD3 | 1.3.6.1.4.1.232.0.13603331 | Severity: Warning -- not failed but attention recommended or required. A physical disk drive was removed while software-activated drive locking was enabled on a drive enclosure that does not support drive locking. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The affected drive enclosure bay is identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD4 | 1.3.6.1.4.1.232.0.13603332 | Severity: Critical -- failure or failure imminent. A physical disk drive that is capable of operating at the loop link rate established by the drive enclosure I/O module was found to be running at a different rate. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The affected physical disk drive is installed in the drive enclosure bay identified in the alarmErrorCode.field.en field. The Fibre Channel loop on which the problem was detected is identified by the content of the alarmErrorCode.field.ec field as follows: 4 = loop A 5 = loop B The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD33 | 1.3.6.1.4.1.232.0.13603379 | Severity: Warning -- not failed but attention recommended or required. The AC input to a drive enclosure power supply has been lost. This makes the remaining power supply a single point of failure. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the affected power supply (1 or 2) is identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD34 | 1.3.6.1.4.1.232.0.13603380 | Severity: Critical -- failure or failure imminent. A drive enclosure power supply is improperly installed or missing. This could affect the drive enclosure air flow and cause an over temperature condition. The operational power supply will automatically shut down after a short period of time, thereby disabling the drive enclosure. This condition remains active until either the problem is corrected, or the operational power supply shuts down, whichever occurs first. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the affected power supply (1 or 2) is identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD35 | 1.3.6.1.4.1.232.0.13603381 | Severity: Critical -- failure or failure imminent. A drive enclosure power supply component has failed. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the affected power supply (1 or 2) is identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD47 | 1.3.6.1.4.1.232.0.13603399 | Severity: Critical -- failure or failure imminent. A drive enclosure blower is not operating properly. This could affect the drive enclosure air flow and cause an over temperature condition. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the affected blower (1 or 2) is identified in the alarmErrorCode.field.en field. The cause of the improper operation is described by the content of the alarmErrorCode.field.ec field as follows: 1 = The blower is operating at a speed that is outside of the Drive Enclosure Environmental Monitoring Unit specified range, possibly because of a bearing problem. 2 = The blower is operating at a speed that is significantly outside of the Drive Enclosure Environmental Monitoring Unit specified range, possibly because of a bearing problem. 3 = The blower has stopped. NOTE: The other blower (if operational) now operates at high speed and is a single point of failure. A single blower operating at high speed can provide sufficient air flow to cool an enclosure and the elements for up to 100 hours. However, operating an enclosure at temperatures approaching an overheating threshold can damage elements and may reduce the MTBF of a specific element. Hewlett-Packard therefore recommends immediate replacement of the defective blower. 4 = The power supply reported an internal blower error. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD4b | 1.3.6.1.4.1.232.0.13603403 | Severity: Critical -- failure or failure imminent. A drive enclosure blower is improperly installed or missing. This affects the drive enclosure air flow and can cause an over temperature condition. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the affected blower (1 or 2) is identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD4c | 1.3.6.1.4.1.232.0.13603404 | Severity: Critical -- failure or failure imminent. Both drive enclosure blowers are missing. This severely affects the drive enclosure air flow and can cause an over temperature condition. The operational power supply(s) will automatically shut down after a short period of time, thereby disabling the drive enclosure. This condition remains active until either the problem is corrected, or the operational power supply(s) shut down, whichever occurs first. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. Note that this event is preceded by a 'drive enclosure blower is improperly installed or missing' event that identifies the location of the first missing blower. The location of the second missing blower (1 or 2) is identified in the alarmErrorCode.field.en field of this event. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD5b | 1.3.6.1.4.1.232.0.13603419 | Severity: Warning -- not failed but attention recommended or required. A drive enclosure temperature sensor out of range condition has been reported by one of the drive enclosure elements. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the temperature sensor (1 through 11) is identified in the alarmErrorCode.field.en field as follows: 1 = Power Supply 1 Exhaust 2 = Power Supply 2 Exhaust 3 = Drive Enclosure Environmental Monitoring Unit 4 = Drive Bay 1 5 = Drive Bay 2 6 = Drive Bay 3 7 = Drive Bay 4 8 = Drive Bay 5 9 = Drive Bay 6 A = Drive Bay 7 B = Drive Bay 8 C = Drive Bay 9 D = Drive Bay 10 E = Drive Bay 11 F = Drive Bay 12 10 = Drive Bay 13 11 = Drive Bay 14 The temperature sensor out of range condition is described by the content of the alarmErrorCode.field.ec field as follows: 1 = The element temperature is approaching, but has not reached, the high temperature CRITICAL threshold. Continued operation under these conditions may result in a CRITICAL condition and may reduce an element's MTBF. 2 = The element temperature is above the high temperature CRITICAL threshold. Continued operation under these conditions may result in element failure. 3 = The element temperature is approaching, but has not reached, the low temperature CRITICAL threshold. Continued operation under these conditions may result in a CRITICAL condition and may reduce an element's MTBF. 4 = The element temperature has reached the low temperature CRITICAL threshold. Continued operation under these conditions may result in element failure. The actual temperature threshold values can be found in the HSV element manager GUI. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD5f | 1.3.6.1.4.1.232.0.13603423 | Severity: Critical -- failure or failure imminent. The average temperature of two of the three temperature sensor groups (i.e., Drive Enclosure Environmental Monitoring Unit, Disk Drives, and Power Supplies) exceeds the CRITICAL level. The operational power supply(s) will automatically shut down after a short period of time, thereby disabling the drive enclosure. This condition remains active until either the problem is corrected, or the operational power supply(s) shut down, whichever occurs first. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. Note that in this case the content of the alarmErrorCode.field.en field is undefined. The actual temperature threshold values can be found in the HSV element manager GUI. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD6f | 1.3.6.1.4.1.232.0.13603439 | Severity: Warning -- not failed but attention recommended or required. An internal Drive Enclosure Environmental Monitoring Unit error has occurred. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the Drive Enclosure Environmental Monitoring Unit is the affected element. The cause of the improper operation is described by the content of the alarmErrorCode.field.ec field as follows: 1 = An internal Drive Enclosure Environmental Monitoring Unit clock error has occurred. 2 = The Inter-IC (I2C) bus is not processing data and the Drive Enclosure Environmental Monitoring Unit is unable to monitor or report the status of the elements or enclosures. 5 = A Backplane NVRAM error has occurred. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD71 | 1.3.6.1.4.1.232.0.13603441 | Severity: Normal -- informational in nature. An internal Drive Enclosure Environmental Monitoring Unit error has occurred. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the Drive Enclosure Environmental Monitoring Unit is the affected element. The cause of the improper operation is described by the content of the alarmErrorCode.field.ec field as follows: 3 = A drive enclosure power supply was shut down. 16 = The Drive Enclosure Environmental Monitoring Unit ESI data has been corrupted. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD72 | 1.3.6.1.4.1.232.0.13603442 | Severity: Warning -- not failed but attention recommended or required. A Drive Enclosure Environmental Monitoring Unit is unable to collect data for the SCSI-3 Enclosure Services (SES) page. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the Drive Enclosure Environmental Monitoring Unit is the affected element. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD7e | 1.3.6.1.4.1.232.0.13603454 | Severity: Warning -- not failed but attention recommended or required. Invalid data was read from a Drive Enclosure Environmental Monitoring Unit NVRAM. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the Drive Enclosure Environmental Monitoring Unit is the affected element. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD7f | 1.3.6.1.4.1.232.0.13603455 | Severity: Warning -- not failed but attention recommended or required. An internal Drive Enclosure Environmental Monitoring Unit error has occurred. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the Drive Enclosure Environmental Monitoring Unit is the affected element. The cause of the improper operation is described by the content of the alarmErrorCode.field.ec field as follows: 11 = The Drive Enclosure Environmental Monitoring Unit cannot write data to the NVRAM. 12 = The Drive Enclosure Environmental Monitoring Unit cannot read data from the NVRAM. 13 = The Field Programmable Gate Array (FPGA) that controls the ESI bus failed to load information required for Drive Enclosure Environmental Monitoring Unit operation. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD82 | 1.3.6.1.4.1.232.0.13603458 | Severity: Warning -- not failed but attention recommended or required. A drive enclosure's address is incorrect or the enclosure has no address. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the Drive Enclosure Environmental Monitoring Unit is the affected element. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD83 | 1.3.6.1.4.1.232.0.13603459 | Severity: Critical -- failure or failure imminent. A Drive Enclosure Environmental Monitoring Unit has experienced a hardware failure. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the Drive Enclosure Environmental Monitoring Unit is the affected element. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. The cause of the improper operation is described by the content of the alarmErrorCode.field.ec field as follows: 15 = Drive Enclosure Environmental Monitoring Unit hardware failure DP. 18 = Drive Enclosure Environmental Monitoring Unit hardware failed BT. 19 = Drive Enclosure Environmental Monitoring Unit ESI driver failure. | ||
| NTF sCellEventTrapD85 | 1.3.6.1.4.1.232.0.13603461 | Severity: Warning -- not failed but attention recommended or required. A drive enclosure power supply failed to respond to a shut down command. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the Drive Enclosure Environmental Monitoring Unit is the affected element. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapD8d | 1.3.6.1.4.1.232.0.13603469 | Severity: Critical -- failure or failure imminent. A drive enclosure transceiver error has been detected. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the transceiver (1 through 4) is identified in the alarmErrorCode.field.en field as follows: 1 = Transceiver 01 2 = Transceiver 02 3 = Transceiver 03 4 = Transceiver 04 The transceiver error condition is described by the content of the alarmErrorCode.field.ec field as follows: 1 = The transceivers on this link are not the same type or they are incompatible with the drive enclosure I/O module. This error prevents the controller from establishing a link with the enclosure drives and eliminates the enclosure dual-loop capability. 2 = The transceiver can no longer detect a data signal. This error prevents the controller from transferring data on a loop and eliminates the enclosure dual-loop capability. 3 = The system has detected an FC-AL bus fault involving a transceiver. This error prevents the controller from transferring data on a loop and eliminates the enclosure dual-loop capability. 4 = The transceiver that was previously in this location has been removed. 5 = The transceiver in the specified location has detected invalid Fibre Channel characters. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapDA1 | 1.3.6.1.4.1.232.0.13603489 | Severity: Critical -- failure or failure imminent. A drive enclosure power supply voltage sensor out of range condition has been reported. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the voltage sensor (1 through 4) is identified in the alarmErrorCode.field.en field as follows: 1 = Power Supply 1 +5 VDC 2 = Power Supply 1 +12 VDC 3 = Power Supply 2 +5 VDC 4 = Power Supply 2 +12 VDC The voltage sensor out of range condition is described by the content of the alarmErrorCode.field.ec field as follows: 1 = The element voltage is approaching, but has not reached, the high voltage CRITICAL threshold. Continued operation under these conditions may result in a CRITICAL condition. 2 = The element voltage is above the high voltage CRITICAL threshold. 3 = The element voltage is approaching, but has not reached, the low voltage CRITICAL threshold. Continued operation under these conditions may result in a CRITICAL condition. 4 = The element voltage has reached the low voltage CRITICAL threshold. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapDB5 | 1.3.6.1.4.1.232.0.13603509 | Severity: Critical -- failure or failure imminent. A drive enclosure power supply current sensor out of range condition has been reported. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the current sensor (1 through 4) is identified in the alarmErrorCode.field.en field as follows: 1 = Power Supply 1 +5 VDC 2 = Power Supply 1 +12 VDC 3 = Power Supply 2 +5 VDC 4 = Power Supply 2 +12 VDC The current sensor out of range condition is described by the content of the alarmErrorCode.field.ec field as follows: 1 = The element current is approaching, but has not reached, the high current CRITICAL threshold. Continued operation under these conditions may result in a CRITICAL condition. 2 = The element current is above the high current CRITICAL threshold. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapDD8 | 1.3.6.1.4.1.232.0.13603544 | Severity: Warning -- not failed but attention recommended or required. A drive enclosure backplane invalid NVRAM read error has occurred. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit.This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the drive enclosure is the affected element. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapDD9 | 1.3.6.1.4.1.232.0.13603545 | Severity: Critical -- failure or failure imminent. A drive enclosure backplane error has occurred. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The alarmErrorCode.field.en field contains the value 1 signifying that the drive enclosure is the affected element. The cause of the improper operation is described by the content of the alarmErrorCode.field.ec field as follows: 11 = Unable to write data to the NVRAM. This problem prevents communication between elements in the enclosure. 12 = Unable to read data from the NVRAM. This problem prevents communication between elements in the enclosure. 13 = NVRAM has not been initialized properly. This is a manufacturing error. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapDDd | 1.3.6.1.4.1.232.0.13603549 | Severity: Critical -- failure or failure imminent. A drive enclosure I/O module error has occurred. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the I/O module (A (01) and B (02)) is identified in the alarmErrorCode.field.en field. The cause of the improper operation is described by the content of the alarmErrorCode.field.ec field as follows: 1 = The I/O module's Fibre Channel link speed is not supported by the backplane. This error prevents the controller from establishing a link with enclosure drives and eliminates the enclosure dual-loop capability. 11 = Unable to write data to the I/O module NVRAM. 12 = Unable to read data from the I/O module NVRAM. 13 = The I/O module that was in this location has been removed. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapDDe | 1.3.6.1.4.1.232.0.13603550 | Severity: Warning -- not failed but attention recommended or required. A drive enclosure I/O module is unable to communicate with the Drive Enclosure Environmental Monitoring Unit. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit. This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the I/O module (A (01) and B (02)) is identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapDEc | 1.3.6.1.4.1.232.0.13603564 | Severity: Warning -- not failed but attention recommended or required. A drive enclosure I/O module invalid NVRAM read error has occurred. The handle field contains the WWN of the drive enclosure containing the Drive Enclosure Environmental Monitoring Unit.This problem was detected by the Drive Enclosure Environmental Monitoring Unit located in the drive enclosure determined by the content of the denclNum field as follows: If denclNum is less than 99, the location is as indicated by the content of the rackNum and denclNum fields. If denclNum is equal to 99, the location is unknown. Note that the content of the rackNum field is undefined in this case. If denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rackNum and denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the rackNum field will not be valid until a future release. The location of the I/O module (A (01) or B (02)) is identified in the alarmErrorCode.field.en field. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrapDF0 | 1.3.6.1.4.1.232.0.13603568 | Severity: Normal -- informational in nature. The status has changed on one or more of the drive enclosures. This is an informational event triggered by the occurrence of a change in the status of a drive enclosure. This event is generated for the HSV element manager GUI and contains no user information. The content of the handle, alarmErrorCode field, denclNum, and rackNum fields have no meaning for this event. The enclosures array shows the drive enclosures available on the Fibre Channel loop pair (0 = Loop A, 1 = Loop B) identified in the loop field. The location of an available drive enclosure is determined by the content of the enclosures.denclNum field as follows: If enclosures.denclNum is less than 99, the location is as indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. If enclosures.denclNum is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rackNum field is undefined in this case. If enclosures.denclNum is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rackNum and enclosures.denclNum fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. Note that the content of the enclosures.rackNum field will not be valid until a future release. | ||
| NTF sCellEventTrap420 | 1.3.6.1.4.1.232.0.13616896 | Severity: Normal -- informational in nature. Indicated Host Fibre Channel port transitioned to link down. | ||
| NTF sCellEventTrap421 | 1.3.6.1.4.1.232.0.13616897 | Severity: Normal -- informational in nature. Indicated Host Fibre Channel port transitioned to link failed. | ||
| NTF sCellEventTrap423 | 1.3.6.1.4.1.232.0.13616899 | Severity: Normal -- informational in nature. An excessive number of link errors were detected on a HSV110 controller's Fibre Channel port. The identity of the affected Fibre Channel port is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number of the affected Fibre Channel port is contained in the port field. This is an informational event triggered by the occurrence of an excessive number of Tachyon chip link status errors detected within a particular link status error type. The number of occurrences of each link status error type is contained in a separate type-specific field (e.g., lossOfSignal, badRxChar, etc.). The HSV110 controller checks each of its Fibre Channel port's for excessive link status errors periodically. | ||
| NTF sCellEventTrap424 | 1.3.6.1.4.1.232.0.13616900 | Severity: Warning -- not failed but attention recommended or required. A Fibre Channel port on the HSV110 controller has failed to respond. The identity of the affected Fibre Channel port is contained in the cerpId field. The HSV110 controller internal Fibre Channel port number of the affected Fibre Channel port is contained in the port field. The peb array contains the port event block information. The peqFrzProdIndex field contains the index to the port event block in use when the Tachyon chip entered the frozen state. The peqProdIndex field contains the index to the next port event block. The peqConsIndex field contains the index to the next port event block to be acted upon. | ||
| NTF sCellEventTrap425 | 1.3.6.1.4.1.232.0.13616901 | Severity: Normal -- informational in nature. Indicated Host Fibre Channel port transitioned to link wedged. | ||
| NTF sCellEventTrap830 | 1.3.6.1.4.1.232.0.13633536 | Severity: Critical -- failure or failure imminent. A failure was detected during the execution of this HSV110 controller's on board diagnostics. | ||
| NTF sCellEventTrap831 | 1.3.6.1.4.1.232.0.13633537 | Severity: Warning -- not failed but attention recommended or required. A GBIC SFF Serial ID Data check code failure was detected during the execution of this HSV110 controller's on board diagnostics. | ||
| NTF sCellEventTrap832 | 1.3.6.1.4.1.232.0.13633538 | Severity: Critical -- failure or failure imminent. A battery assembly failure was detected during the execution of this HSV110 controller's on board diagnostics. | ||
| NTF sCellEventTrap833 | 1.3.6.1.4.1.232.0.13633539 | Severity: Critical -- failure or failure imminent. A battery assembly failure was detected during the execution of this HSV110 controller's on board diagnostics. | ||
| NTF sCellEventTrap834 | 1.3.6.1.4.1.232.0.13633540 | Severity: Critical -- failure or failure imminent. A battery assembly communication failure was detected during the execution of this HSV110 controller's on board diagnostics. | ||
| NTF sCellEventTrap835 | 1.3.6.1.4.1.232.0.13633541 | Severity: Critical -- failure or failure imminent. A battery assembly communication failure was detected during the execution of this HSV110 controller's on board diagnostics. | ||
| NTF sCellEventTrap836 | 1.3.6.1.4.1.232.0.13633542 | Severity: Critical -- failure or failure imminent. A soft cache memory ECC error or indication of low battery voltage was detected during the execution of this HSV110 controller's on board diagnostics. | ||
| NTF mngmtAgentTrap1 | 1.3.6.1.4.1.232.0.136000001 | Object Already Exists | ||
| NTF mngmtAgentTrap2 | 1.3.6.1.4.1.232.0.136000002 | Supplied Buffer Too Small | ||
| NTF mngmtAgentTrap3 | 1.3.6.1.4.1.232.0.136000003 | Object Already Assigned | ||
| NTF mngmtAgentTrap4 | 1.3.6.1.4.1.232.0.136000004 | Insufficient Available Data Storage | ||
| NTF mngmtAgentTrap5 | 1.3.6.1.4.1.232.0.136000005 | Internal Error | ||
| NTF mngmtAgentTrap6 | 1.3.6.1.4.1.232.0.136000006 | Invalid status for logical disk | ||
| NTF mngmtAgentTrap7 | 1.3.6.1.4.1.232.0.136000007 | Invalid Class | ||
| NTF mngmtAgentTrap8 | 1.3.6.1.4.1.232.0.136000008 | Invalid Function | ||
| NTF mngmtAgentTrap9 | 1.3.6.1.4.1.232.0.136000009 | Invalid Logical Disk Block State | ||
| NTF mngmtAgentTrap10 | 1.3.6.1.4.1.232.0.136000010 | Invalid Loop Configuration | ||
| NTF mngmtAgentTrap11 | 1.3.6.1.4.1.232.0.136000011 | Invalid Parameter | ||
| NTF mngmtAgentTrap12 | 1.3.6.1.4.1.232.0.136000012 | Invalid Parameter handle | ||
| NTF mngmtAgentTrap13 | 1.3.6.1.4.1.232.0.136000013 | Invalid Parameter Id | ||
| NTF mngmtAgentTrap14 | 1.3.6.1.4.1.232.0.136000014 | Invalid Quorum Configuration | ||
| NTF mngmtAgentTrap15 | 1.3.6.1.4.1.232.0.136000015 | Invalid Target Handle | ||
| NTF mngmtAgentTrap16 | 1.3.6.1.4.1.232.0.136000016 | Invalid Target Id | ||
| NTF mngmtAgentTrap17 | 1.3.6.1.4.1.232.0.136000017 | Invalid Time | ||
| NTF mngmtAgentTrap18 | 1.3.6.1.4.1.232.0.136000018 | Media is Inaccessible | ||
| NTF mngmtAgentTrap19 | 1.3.6.1.4.1.232.0.136000019 | No Fibre Channel Port | ||
| NTF mngmtAgentTrap20 | 1.3.6.1.4.1.232.0.136000020 | No Image | ||
| NTF mngmtAgentTrap21 | 1.3.6.1.4.1.232.0.136000021 | No Permission | ||
| NTF mngmtAgentTrap22 | 1.3.6.1.4.1.232.0.136000022 | Storage system not initialized | ||
| NTF mngmtAgentTrap23 | 1.3.6.1.4.1.232.0.136000023 | Not a Loop Port | ||
| NTF mngmtAgentTrap24 | 1.3.6.1.4.1.232.0.136000024 | Not a Participating Controller | ||
| NTF mngmtAgentTrap25 | 1.3.6.1.4.1.232.0.136000025 | Objects in your system are in use, and their state prevents the operation you wish to perform. | ||
| NTF mngmtAgentTrap26 | 1.3.6.1.4.1.232.0.136000026 | Parameter Object Does Not Exist | ||
| NTF mngmtAgentTrap27 | 1.3.6.1.4.1.232.0.136000027 | Target Object Does Not Exist | ||
| NTF mngmtAgentTrap28 | 1.3.6.1.4.1.232.0.136000028 | Timeout | ||
| NTF mngmtAgentTrap29 | 1.3.6.1.4.1.232.0.136000029 | Unknown Id | ||
| NTF mngmtAgentTrap30 | 1.3.6.1.4.1.232.0.136000030 | Unknown Parameter Handle | ||
| NTF mngmtAgentTrap31 | 1.3.6.1.4.1.232.0.136000031 | Unrecoverable Media Error | ||
| NTF mngmtAgentTrap32 | 1.3.6.1.4.1.232.0.136000032 | Invalid State | ||
| NTF mngmtAgentTrap33 | 1.3.6.1.4.1.232.0.136000033 | Transport Error | ||
| NTF mngmtAgentTrap34 | 1.3.6.1.4.1.232.0.136000034 | Volume is Missing | ||
| NTF mngmtAgentTrap35 | 1.3.6.1.4.1.232.0.136000035 | Invalid Cursor | ||
| NTF mngmtAgentTrap36 | 1.3.6.1.4.1.232.0.136000036 | Invalid Target for the Operation | ||
| NTF mngmtAgentTrap37 | 1.3.6.1.4.1.232.0.136000037 | No More Events | ||
| NTF mngmtAgentTrap38 | 1.3.6.1.4.1.232.0.136000038 | Lock Busy | ||
| NTF mngmtAgentTrap39 | 1.3.6.1.4.1.232.0.136000039 | Time Not Set | ||
| NTF mngmtAgentTrap40 | 1.3.6.1.4.1.232.0.136000040 | Not a Supported Version | ||
| NTF mngmtAgentTrap41 | 1.3.6.1.4.1.232.0.136000041 | No Logical Disk for Vdisk | ||
| NTF mngmtAgentTrap42 | 1.3.6.1.4.1.232.0.136000042 | Logical disk Presented | ||
| NTF mngmtAgentTrap43 | 1.3.6.1.4.1.232.0.136000043 | Operation Denied On Slave | ||
| NTF mngmtAgentTrap44 | 1.3.6.1.4.1.232.0.136000044 | Not licensed for data replication | ||
| NTF mngmtAgentTrap45 | 1.3.6.1.4.1.232.0.136000045 | Not DR group member | ||
| NTF mngmtAgentTrap46 | 1.3.6.1.4.1.232.0.136000046 | Invalid DR mode | ||
| NTF mngmtAgentTrap47 | 1.3.6.1.4.1.232.0.136000047 | Invalid DR State | ||
| NTF mngmtAgentTrap48 | 1.3.6.1.4.1.232.0.136000048 | Security credentials needed. Please update your system's ID and password in the Storage System Access menu. | ||
| NTF mngmtAgentTrap49 | 1.3.6.1.4.1.232.0.136000049 | Security credentials supplied were invalid. Please update your system's ID and password in the Storage System Access menu. | ||
| NTF mngmtAgentTrap50 | 1.3.6.1.4.1.232.0.136000050 | Security credentials supplied were invalid. Please update your system's ID and password in the Storage System Access menu. | ||
| NTF mngmtAgentTrap51 | 1.3.6.1.4.1.232.0.136000051 | Storage system connection down | ||
| NTF mngmtAgentTrap52 | 1.3.6.1.4.1.232.0.136000052 | DR group empty | ||
| NTF mngmtAgentTrap53 | 1.3.6.1.4.1.232.0.136000053 | Incompatible attribute | ||
| NTF mngmtAgentTrap54 | 1.3.6.1.4.1.232.0.136000054 | Vdisk is a DR group member | ||
| NTF mngmtAgentTrap55 | 1.3.6.1.4.1.232.0.136000055 | Vdisk is a DR log unit | ||
| NTF mngmtAgentTrap56 | 1.3.6.1.4.1.232.0.136000056 | Cache batteries failed or missing. | ||
| NTF mngmtAgentTrap57 | 1.3.6.1.4.1.232.0.136000057 | Vdisk is not presented | ||
| NTF mngmtAgentTrap58 | 1.3.6.1.4.1.232.0.136000058 | Other controller failed | ||
| NTF mngmtAgentTrap59 | 1.3.6.1.4.1.232.0.136000059 | Maximum Number of Objects Exceeded. | ||
| NTF mngmtAgentTrap60 | 1.3.6.1.4.1.232.0.136000060 | Max size | ||
| NTF mngmtAgentTrap61 | 1.3.6.1.4.1.232.0.136000061 | Password mismatch. Please update your system's password in the Storage System Access menu. Continued attempts to access this storage system with an incorrect password will disable management of this storage system. | ||
| NTF mngmtAgentTrap62 | 1.3.6.1.4.1.232.0.136000062 | DR group is merging | ||
| NTF mngmtAgentTrap63 | 1.3.6.1.4.1.232.0.136000063 | DR group is logging | ||
| NTF mngmtAgentTrap64 | 1.3.6.1.4.1.232.0.136000064 | Connection is suspended | ||
| NTF mngmtAgentTrap65 | 1.3.6.1.4.1.232.0.136000065 | Bad image header | ||
| NTF mngmtAgentTrap66 | 1.3.6.1.4.1.232.0.136000066 | Bad image | ||
| NTF mngmtAgentTrap67 | 1.3.6.1.4.1.232.0.136000067 | Image too large | ||
| NTF mngmtAgentTrap68 | 1.3.6.1.4.1.232.0.136000068 | EMU not available | ||
| NTF mngmtAgentTrap69 | 1.3.6.1.4.1.232.0.136000069 | EMU indefinite delay | ||
| NTF mngmtAgentTrap70 | 1.3.6.1.4.1.232.0.136000070 | Image incompatible with system configuration. Version conflict in upgrade or downgrade not allowed. | ||
| NTF mngmtAgentTrap71 | 1.3.6.1.4.1.232.0.136000071 | Bad image segment | ||
| NTF mngmtAgentTrap72 | 1.3.6.1.4.1.232.0.136000072 | Image already loaded | ||
| NTF mngmtAgentTrap73 | 1.3.6.1.4.1.232.0.136000073 | Image Write Error | ||
| NTF mngmtAgentTrap74 | 1.3.6.1.4.1.232.0.136000074 | Logical Disk Sharing | ||
| NTF mngmtAgentTrap75 | 1.3.6.1.4.1.232.0.136000075 | Bad Image Size | ||
| NTF mngmtAgentTrap76 | 1.3.6.1.4.1.232.0.136000076 | Image Load Busy | ||
| NTF mngmtAgentTrap77 | 1.3.6.1.4.1.232.0.136000077 | Volume Failure Predicted | ||
| NTF mngmtAgentTrap78 | 1.3.6.1.4.1.232.0.136000078 | Background allocation on the destination member is in progress. This action must complete before any others can be initiated . | ||
| NTF mngmtAgentTrap79 | 1.3.6.1.4.1.232.0.136000079 | Invalid Predecessor Vdisk Condition | ||
| NTF mngmtAgentTrap80 | 1.3.6.1.4.1.232.0.136000080 | Invalid Volume Usage | ||
| NTF mngmtAgentTrap81 | 1.3.6.1.4.1.232.0.136000081 | Minimum Volumes In Disk Group | ||
| NTF mngmtAgentTrap82 | 1.3.6.1.4.1.232.0.136000082 | Shutdown In Progress | ||
| NTF mngmtAgentTrap83 | 1.3.6.1.4.1.232.0.136000083 | Not Ready | ||
| NTF mngmtAgentTrap84 | 1.3.6.1.4.1.232.0.136000084 | Is Snapshot | ||
| NTF mngmtAgentTrap85 | 1.3.6.1.4.1.232.0.136000085 | Cannot add or remove DR group member. Mirror cache must be active for this Vdisk. Check controller cache condition. | ||
| NTF mngmtAgentTrap86 | 1.3.6.1.4.1.232.0.136000086 | Inoperative | ||
| NTF mngmtAgentTrap87 | 1.3.6.1.4.1.232.0.136000087 | Disk group inoperative or less than 8 disks in group | ||
| NTF mngmtAgentTrap88 | 1.3.6.1.4.1.232.0.136000088 | Storage system inoperative | ||
| NTF mngmtAgentTrap89 | 1.3.6.1.4.1.232.0.136000089 | Failsafe Locked | ||
| NTF mngmtAgentTrap90 | 1.3.6.1.4.1.232.0.136000090 | Data Flush Incomplete | ||
| NTF mngmtAgentTrap91 | 1.3.6.1.4.1.232.0.136000091 | Redundancy Mirrored Inoperative | ||
| NTF mngmtAgentTrap92 | 1.3.6.1.4.1.232.0.136000092 | Duplicate LUN | ||
| NTF mngmtAgentTrap93 | 1.3.6.1.4.1.232.0.136000093 | Other remote controller failed | ||
| NTF mngmtAgentTrap94 | 1.3.6.1.4.1.232.0.136000094 | Unknown remote Vdisk | ||
| NTF mngmtAgentTrap95 | 1.3.6.1.4.1.232.0.136000095 | Unknown remote DR group | ||
| NTF mngmtAgentTrap96 | 1.3.6.1.4.1.232.0.136000096 | PLDMC failed | ||
| NTF mngmtAgentTrap97 | 1.3.6.1.4.1.232.0.136000097 | Storage system could not be locked. System busy. Try command again. | ||
| NTF mngmtAgentTrap98 | 1.3.6.1.4.1.232.0.136000098 | Error on remote storage system. | ||
| NTF mngmtAgentTrap99 | 1.3.6.1.4.1.232.0.136000099 | This operation can only be completed when the source-destination connection is down. | ||
| NTF mngmtAgentTrap100 | 1.3.6.1.4.1.232.0.136000100 | Login required - password changed. | ||
| NTF mngmtAgentTrap101 | 1.3.6.1.4.1.232.0.136000101 | Numerous login attempts have been detected that uses an incorrect password. Please update your system's password in the Storage System Access menu. | ||
| NTF mngmtAgentTrap102 | 1.3.6.1.4.1.232.0.136000102 | Invalid cookie | ||
| NTF mngmtAgentTrap103 | 1.3.6.1.4.1.232.0.136000103 | Login timed out | ||
| NTF mngmtAgentTrap104 | 1.3.6.1.4.1.232.0.136000104 | Max snapshot depth reached | ||
| NTF mngmtAgentTrap105 | 1.3.6.1.4.1.232.0.136000105 | Attribute mismatch | ||
| NTF mngmtAgentTrap106 | 1.3.6.1.4.1.232.0.136000106 | The password has been set in Command View EVA. The same password still needs to be set in the controllers. | ||
| NTF mngmtAgentTrap107 | 1.3.6.1.4.1.232.0.136000107 | Not host port | ||
| NTF mngmtAgentTrap108 | 1.3.6.1.4.1.232.0.136000108 | Duplicate Lun WWID | ||
| NTF mngmtAgentTrap109 | 1.3.6.1.4.1.232.0.136000109 | System Inoperative | ||
| NTF mngmtAgentTrap110 | 1.3.6.1.4.1.232.0.136000110 | SnapClone Active | ||
| NTF mngmtAgentTrap111 | 1.3.6.1.4.1.232.0.136000111 | Emu Load Busy | ||
| NTF mngmtAgentTrap112 | 1.3.6.1.4.1.232.0.136000112 | Duplicate User Name | ||
| NTF mngmtAgentTrap113 | 1.3.6.1.4.1.232.0.136000113 | Drive Reserved For Code Load | ||
| NTF mngmtAgentTrap114 | 1.3.6.1.4.1.232.0.136000114 | Already Presented | ||
| NTF mngmtAgentTrap115 | 1.3.6.1.4.1.232.0.136000115 | Invalid remote storage system | ||
| NTF mngmtAgentTrap116 | 1.3.6.1.4.1.232.0.136000116 | No Lock | ||
| NTF mngmtAgentTrap117 | 1.3.6.1.4.1.232.0.136000117 | Maximum Number of Members Exceeded | ||
| NTF mngmtAgentTrap118 | 1.3.6.1.4.1.232.0.136000118 | Max Destinations | ||
| NTF mngmtAgentTrap119 | 1.3.6.1.4.1.232.0.136000119 | Empty User Name | ||
| NTF mngmtAgentTrap120 | 1.3.6.1.4.1.232.0.136000120 | Storage system already initialized | ||
| NTF mngmtAgentTrap121 | 1.3.6.1.4.1.232.0.136000121 | Already Open | ||
| NTF mngmtAgentTrap122 | 1.3.6.1.4.1.232.0.136000122 | Session Not Open | ||
| NTF mngmtAgentTrap123 | 1.3.6.1.4.1.232.0.136000123 | Not Marked Inoperative | ||
| NTF mngmtAgentTrap124 | 1.3.6.1.4.1.232.0.136000124 | Media Not Available | ||
| NTF mngmtAgentTrap125 | 1.3.6.1.4.1.232.0.136000125 | Battery System Failed | ||
| NTF mngmtAgentTrap126 | 1.3.6.1.4.1.232.0.136000126 | DR Group Member Is Cache Data Lost | ||
| NTF mngmtAgentTrap127 | 1.3.6.1.4.1.232.0.136000127 | Internal Lock Collision | ||
| NTF mngmtAgentTrap128 | 1.3.6.1.4.1.232.0.136000128 | OCP Error | ||
| NTF mngmtAgentTrap129 | 1.3.6.1.4.1.232.0.136000129 | Mirror Offline | ||
| NTF mngmtAgentTrap130 | 1.3.6.1.4.1.232.0.136000130 | This operation cannot be completed if failsafe mode is enabled. | ||
| NTF mngmtAgentTrap131 | 1.3.6.1.4.1.232.0.136000131 | Drive firmware load abort due to Raid0 virtual disk(s). | ||
| NTF mngmtAgentTrap132 | 1.3.6.1.4.1.232.0.136000132 | Fibre channel ports are unavailable. | ||
| NTF mngmtAgentTrap133 | 1.3.6.1.4.1.232.0.136000133 | The storage system has reached its maximum number of DR relationship. | ||
| NTF mngmtAgentTrap1000 | 1.3.6.1.4.1.232.0.136001000 | Logical Disk Condition Change | ||
| NTF mngmtAgentTrap1001 | 1.3.6.1.4.1.232.0.136001001 | Storage system is FULL **critical** | ||
| NTF mngmtAgentTrap1002 | 1.3.6.1.4.1.232.0.136001002 | Storage system is almost FULL. Disk group at or above maximum capacity warning level. | ||
| NTF mngmtAgentTrap1003 | 1.3.6.1.4.1.232.0.136001003 | Controller Cache Battery Condition Change | ||
| NTF mngmtAgentTrap1004 | 1.3.6.1.4.1.232.0.136001004 | Controller Cache Condition Change | ||
| NTF mngmtAgentTrap1005 | 1.3.6.1.4.1.232.0.136001005 | Controller Condition Change | ||
| NTF mngmtAgentTrap1006 | 1.3.6.1.4.1.232.0.136001006 | Controller FC Port Condition Change | ||
| NTF mngmtAgentTrap1007 | 1.3.6.1.4.1.232.0.136001007 | Physical Device Condition Change | ||
| NTF mngmtAgentTrap1008 | 1.3.6.1.4.1.232.0.136001008 | Physical Store Condition Change | ||
| NTF mngmtAgentTrap1009 | 1.3.6.1.4.1.232.0.136001009 | Host condition change | ||
| NTF mngmtAgentTrap1010 | 1.3.6.1.4.1.232.0.136001010 | Storage system time has been set | ||
| NTF mngmtAgentTrap1011 | 1.3.6.1.4.1.232.0.136001011 | Volume Condition change | ||
| NTF mngmtAgentTrap1012 | 1.3.6.1.4.1.232.0.136001012 | Volume insufficientResources condition change | ||
| NTF mngmtAgentTrap1013 | 1.3.6.1.4.1.232.0.136001013 | Volume Quorum Disk change | ||
| NTF mngmtAgentTrap1014 | 1.3.6.1.4.1.232.0.136001014 | The state of an object in the system has changed. View adjacent events for more detail. | ||
| NTF mngmtAgentTrap2001 | 1.3.6.1.4.1.232.0.136002001 | Startup Failed | ||
| NTF mngmtAgentTrap2002 | 1.3.6.1.4.1.232.0.136002002 | Management agent event log cleared successfully | ||
| NTF mngmtAgentTrap2003 | 1.3.6.1.4.1.232.0.136002003 | Invalid name specified for storage system | ||
| NTF mngmtAgentTrap2004 | 1.3.6.1.4.1.232.0.136002004 | Storage system is not initialized | ||
| NTF mngmtAgentTrap2006 | 1.3.6.1.4.1.232.0.136002006 | Invalid name specified for Vdisk | ||
| NTF mngmtAgentTrap2007 | 1.3.6.1.4.1.232.0.136002007 | Vdisk name exceeds maximum length | ||
| NTF mngmtAgentTrap2008 | 1.3.6.1.4.1.232.0.136002008 | Invalid parameter specified for Vdisk | ||
| NTF mngmtAgentTrap2010 | 1.3.6.1.4.1.232.0.136002010 | Specified Vdisk size exceeds available size | ||
| NTF mngmtAgentTrap2011 | 1.3.6.1.4.1.232.0.136002011 | There are not enough disk drives to create a disk group | ||
| NTF mngmtAgentTrap2012 | 1.3.6.1.4.1.232.0.136002012 | Number of devices exceeds the available number of disks | ||
| NTF mngmtAgentTrap2013 | 1.3.6.1.4.1.232.0.136002013 | Number of devices is less than the minimum number required to create a disk group | ||
| NTF mngmtAgentTrap2016 | 1.3.6.1.4.1.232.0.136002016 | Completed unpresenting virtual disk to host | ||
| NTF mngmtAgentTrap2021 | 1.3.6.1.4.1.232.0.136002021 | Invalid refresh interval value. Should be numeric and non-negative. | ||
| NTF mngmtAgentTrap2022 | 1.3.6.1.4.1.232.0.136002022 | Invalid security message. Should not be blank. | ||
| NTF mngmtAgentTrap2023 | 1.3.6.1.4.1.232.0.136002023 | Vdisk Create Complete | ||
| NTF mngmtAgentTrap2025 | 1.3.6.1.4.1.232.0.136002025 | Storage system successfully initialized | ||
| NTF mngmtAgentTrap2026 | 1.3.6.1.4.1.232.0.136002026 | Device Added Successfully | ||
| NTF mngmtAgentTrap2030 | 1.3.6.1.4.1.232.0.136002030 | Refresh Interval Changed | ||
| NTF mngmtAgentTrap2031 | 1.3.6.1.4.1.232.0.136002031 | Security Message Changed | ||
| NTF mngmtAgentTrap2032 | 1.3.6.1.4.1.232.0.136002032 | Present Vdisk to a Host - Complete | ||
| NTF mngmtAgentTrap2033 | 1.3.6.1.4.1.232.0.136002033 | Control Startup Complete | ||
| NTF mngmtAgentTrap2034 | 1.3.6.1.4.1.232.0.136002034 | Change Device Usage Complete | ||
| NTF mngmtAgentTrap2035 | 1.3.6.1.4.1.232.0.136002035 | Control Shutdown - Complete | ||
| NTF mngmtAgentTrap2036 | 1.3.6.1.4.1.232.0.136002036 | Controller Shutdown - Complete | ||
| NTF mngmtAgentTrap2038 | 1.3.6.1.4.1.232.0.136002038 | Control Memory Allocation Failure | ||
| NTF mngmtAgentTrap2040 | 1.3.6.1.4.1.232.0.136002040 | Access level denied or session activity timeout. Please log in again. | ||
| NTF mngmtAgentTrap2041 | 1.3.6.1.4.1.232.0.136002041 | Vdisk Snapshot - Completed | ||
| NTF mngmtAgentTrap2042 | 1.3.6.1.4.1.232.0.136002042 | Vdisk Snapclone - Completed | ||
| NTF mngmtAgentTrap2047 | 1.3.6.1.4.1.232.0.136002047 | Host record added successfully | ||
| NTF mngmtAgentTrap2048 | 1.3.6.1.4.1.232.0.136002048 | Logical component deleted successfully | ||
| NTF mngmtAgentTrap2049 | 1.3.6.1.4.1.232.0.136002049 | Invalid host adapter ID | ||
| NTF mngmtAgentTrap2050 | 1.3.6.1.4.1.232.0.136002050 | Specified device is already a member of the system | ||
| NTF mngmtAgentTrap2051 | 1.3.6.1.4.1.232.0.136002051 | Create Folder - Completed | ||
| NTF mngmtAgentTrap2052 | 1.3.6.1.4.1.232.0.136002052 | Change Object Properties - Completed | ||
| NTF mngmtAgentTrap2057 | 1.3.6.1.4.1.232.0.136002057 | Completed disk group creation | ||
| NTF mngmtAgentTrap2058 | 1.3.6.1.4.1.232.0.136002058 | Added host port | ||
| NTF mngmtAgentTrap2059 | 1.3.6.1.4.1.232.0.136002059 | Discarded host port | ||
| NTF mngmtAgentTrap2060 | 1.3.6.1.4.1.232.0.136002060 | EMU/Shelf code load complete | ||
| NTF mngmtAgentTrap2061 | 1.3.6.1.4.1.232.0.136002061 | Operation will exceed the available capacity of the disk group | ||
| NTF mngmtAgentTrap2062 | 1.3.6.1.4.1.232.0.136002062 | Controller(s) code load complete | ||
| NTF mngmtAgentTrap2063 | 1.3.6.1.4.1.232.0.136002063 | The target device is not in the right condition to perform the operation | ||
| NTF mngmtAgentTrap2064 | 1.3.6.1.4.1.232.0.136002064 | Storage system Device Addition Policy changed successfully | ||
| NTF mngmtAgentTrap2065 | 1.3.6.1.4.1.232.0.136002065 | Maximum number of disk groups exceeded | ||
| NTF mngmtAgentTrap2066 | 1.3.6.1.4.1.232.0.136002066 | Nsa object discard failed. | ||
| NTF mngmtAgentTrap2067 | 1.3.6.1.4.1.232.0.136002067 | There are not enough disks to meet the minimum number requirement | ||
| NTF mngmtAgentTrap2068 | 1.3.6.1.4.1.232.0.136002068 | Entry added successfully in the password file | ||
| NTF mngmtAgentTrap2069 | 1.3.6.1.4.1.232.0.136002069 | Entry updated successfully in the password file | ||
| NTF mngmtAgentTrap2070 | 1.3.6.1.4.1.232.0.136002070 | Entry discarded successfully in the password file | ||
| NTF mngmtAgentTrap2071 | 1.3.6.1.4.1.232.0.136002071 | Storage system is not responding in a timely manner and has been placed into an unknown state. This may be due to a prior command with an excessively long execution time, high I/O load, or a network communications error. Recovery will automatically occur when the storage system is able to respond. | ||
| NTF mngmtAgentTrap2072 | 1.3.6.1.4.1.232.0.136002072 | Object not found. Operation on this object is completed | ||
| NTF mngmtAgentTrap2073 | 1.3.6.1.4.1.232.0.136002073 | There is no more available space to create a Vdisk | ||
| NTF mngmtAgentTrap2074 | 1.3.6.1.4.1.232.0.136002074 | Name or comments contains invalid character(s) | ||
| NTF mngmtAgentTrap2075 | 1.3.6.1.4.1.232.0.136002075 | Duplicate - Another object with the same name exists. | ||
| NTF mngmtAgentTrap2076 | 1.3.6.1.4.1.232.0.136002076 | No healthy disk group(s) to create a Vdisk. Resolve any abnormal conditions in the disk group first. | ||
| NTF mngmtAgentTrap2077 | 1.3.6.1.4.1.232.0.136002077 | Operating System ID must be a valid number. | ||
| NTF mngmtAgentTrap2078 | 1.3.6.1.4.1.232.0.136002078 | Watchdog successfully started | ||
| NTF mngmtAgentTrap2079 | 1.3.6.1.4.1.232.0.136002079 | Watchdog successfully stopped | ||
| NTF mngmtAgentTrap2080 | 1.3.6.1.4.1.232.0.136002080 | Delete Event Config List failed | ||
| NTF mngmtAgentTrap2081 | 1.3.6.1.4.1.232.0.136002081 | Disk group meltdown repaired successfully. | ||
| NTF mngmtAgentTrap2082 | 1.3.6.1.4.1.232.0.136002082 | There are no available LUNs to present this Vdisk. | ||
| NTF mngmtAgentTrap2083 | 1.3.6.1.4.1.232.0.136002083 | Controller time synchronization turned on. | ||
| NTF mngmtAgentTrap2084 | 1.3.6.1.4.1.232.0.136002084 | Controller time synchronization turned off. | ||
| NTF mngmtAgentTrap2085 | 1.3.6.1.4.1.232.0.136002085 | System login failed. Invalid password. | ||
| NTF mngmtAgentTrap2086 | 1.3.6.1.4.1.232.0.136002086 | System is not set for password validation. | ||
| NTF mngmtAgentTrap2087 | 1.3.6.1.4.1.232.0.136002087 | Agent is already logged in to this system. | ||
| NTF mngmtAgentTrap2088 | 1.3.6.1.4.1.232.0.136002088 | Storage system time set to custom time. Controller time synchronization automatically turned off. | ||
| NTF mngmtAgentTrap2089 | 1.3.6.1.4.1.232.0.136002089 | Storage system time set to SAN appliance time. | ||
| NTF mngmtAgentTrap2090 | 1.3.6.1.4.1.232.0.136002090 | Storage system time set to browser time. Controller time synchronization automatically turned off. | ||
| NTF mngmtAgentTrap2091 | 1.3.6.1.4.1.232.0.136002091 | Storage system time set to controller time. Controller time synchronization automatically turned off. | ||
| NTF mngmtAgentTrap2092 | 1.3.6.1.4.1.232.0.136002092 | Unable to find DR Group on remote storage system. | ||
| NTF mngmtAgentTrap2093 | 1.3.6.1.4.1.232.0.136002093 | A host must have at least one port. Cannot delete the only host port available. | ||
| NTF mngmtAgentTrap2095 | 1.3.6.1.4.1.232.0.136002095 | Host creation failed. Maximum number of hosts reached. | ||
| NTF mngmtAgentTrap2096 | 1.3.6.1.4.1.232.0.136002096 | Port already exists for this host. | ||
| NTF mngmtAgentTrap2097 | 1.3.6.1.4.1.232.0.136002097 | Error reading parameter string. String is empty. | ||
| NTF mngmtAgentTrap2098 | 1.3.6.1.4.1.232.0.136002098 | Command could not be completed on Master. Controller not found. | ||
| NTF mngmtAgentTrap2099 | 1.3.6.1.4.1.232.0.136002099 | Command could not be completed on Slave. Controller not found. | ||
| NTF mngmtAgentTrap2100 | 1.3.6.1.4.1.232.0.136002100 | Password access for all known storage systems is already enabled or set. | ||
| NTF mngmtAgentTrap2102 | 1.3.6.1.4.1.232.0.136002102 | The local storage system has reached the maximum allowable DR relationship. | ||
| NTF mngmtAgentTrap2103 | 1.3.6.1.4.1.232.0.136002103 | The remote storage system has reached the maximum allowable DR relationship. | ||
| NTF mngmtAgentTrap3001 | 1.3.6.1.4.1.232.0.136003001 | Event Manager Offline | ||
| NTF mngmtAgentTrap3002 | 1.3.6.1.4.1.232.0.136003002 | Event Manager Online | ||
| NTF mngmtAgentTrap3003 | 1.3.6.1.4.1.232.0.136003003 | Event Manager - Startup Failed | ||
| NTF mngmtAgentTrap3004 | 1.3.6.1.4.1.232.0.136003004 | Event Manager - Startup Complete | ||
| NTF mngmtAgentTrap3007 | 1.3.6.1.4.1.232.0.136003007 | Event Manager - Shutdown Complete | ||
| NTF mngmtAgentTrap3009 | 1.3.6.1.4.1.232.0.136003009 | Unable to open NSA Local Event Log File | ||
| NTF mngmtAgentTrap3012 | 1.3.6.1.4.1.232.0.136003012 | Unable to open Local Temp Event File - possibly no initialized SC | ||
| NTF mngmtAgentTrap3013 | 1.3.6.1.4.1.232.0.136003013 | Unable to clear NSA Local Event Log File | ||
| NTF mngmtAgentTrap3015 | 1.3.6.1.4.1.232.0.136003015 | Unable to clear NSA Event Log File | ||
| NTF mngmtAgentTrap3016 | 1.3.6.1.4.1.232.0.136003016 | Local log file found on startup | ||
| NTF mngmtAgentTrap3017 | 1.3.6.1.4.1.232.0.136003017 | Event Queue Flush Error | ||
| NTF mngmtAgentTrap3019 | 1.3.6.1.4.1.232.0.136003019 | EM File Manager Online | ||
| NTF mngmtAgentTrap3020 | 1.3.6.1.4.1.232.0.136003020 | EM File Manager Offline | ||
| NTF mngmtAgentTrap3021 | 1.3.6.1.4.1.232.0.136003021 | EM Log Manager Online | ||
| NTF mngmtAgentTrap3022 | 1.3.6.1.4.1.232.0.136003022 | EM Log Manager Offline | ||
| NTF mngmtAgentTrap3024 | 1.3.6.1.4.1.232.0.136003024 | Local NSA logfile is empty | ||
| NTF mngmtAgentTrap3025 | 1.3.6.1.4.1.232.0.136003025 | Event Queue Online | ||
| NTF mngmtAgentTrap3028 | 1.3.6.1.4.1.232.0.136003028 | Status Descriptions Unavailable | ||
| NTF mngmtAgentTrap3029 | 1.3.6.1.4.1.232.0.136003029 | EM Description Mngr Online | ||
| NTF mngmtAgentTrap3035 | 1.3.6.1.4.1.232.0.136003035 | EM: NSA log file unavailable | ||
| NTF mngmtAgentTrap3036 | 1.3.6.1.4.1.232.0.136003036 | EM Memory Allocation Error | ||
| NTF mngmtAgentTrap3037 | 1.3.6.1.4.1.232.0.136003037 | EM: Local Event Configuration File Unavailable | ||
| NTF mngmtAgentTrap3038 | 1.3.6.1.4.1.232.0.136003038 | EM: MLD Notification File Unavailable - retrieving local backup copy | ||
| NTF mngmtAgentTrap3039 | 1.3.6.1.4.1.232.0.136003039 | EM: Local Notification Host List File Unavailable | ||
| NTF mngmtAgentTrap3044 | 1.3.6.1.4.1.232.0.136003044 | Override this description with missing filename | ||
| NTF mngmtAgentTrap3045 | 1.3.6.1.4.1.232.0.136003045 | Invalid storage system event sequence number - can't retrieve event | ||
| NTF mngmtAgentTrap3046 | 1.3.6.1.4.1.232.0.136003046 | Invalid SC termination event sequence number - can't retrieve event | ||
| NTF mngmtAgentTrap3047 | 1.3.6.1.4.1.232.0.136003047 | EM: Event config file unavailable from MLD - retrieving local backup copy | ||
| NTF mngmtAgentTrap3048 | 1.3.6.1.4.1.232.0.136003048 | EM: Local user defined event state file unavailable | ||
| NTF mngmtAgentTrap3049 | 1.3.6.1.4.1.232.0.136003049 | EM: EMU event monitoring thread unable to start | ||
| NTF mngmtAgentTrap3050 | 1.3.6.1.4.1.232.0.136003050 | EM: EMU event - this description will be overwritten | ||
| NTF mngmtAgentTrap3051 | 1.3.6.1.4.1.232.0.136003051 | EM: Failed to write Event Config file to MLD | ||
| NTF mngmtAgentTrap3053 | 1.3.6.1.4.1.232.0.136003053 | EM: Event Configuration Filename Error or File empty | ||
| NTF mngmtAgentTrap3054 | 1.3.6.1.4.1.232.0.136003054 | EM: Notification Hostlist Filename Error or File empty | ||
| NTF mngmtAgentTrap3055 | 1.3.6.1.4.1.232.0.136003055 | EM: Event Config List Object Reference Error | ||
| NTF mngmtAgentTrap3056 | 1.3.6.1.4.1.232.0.136003056 | EM: SC Parse File successfully uploaded | ||
| NTF mngmtAgentTrap3057 | 1.3.6.1.4.1.232.0.136003057 | EM: SC Parse File upload failed | ||
| NTF mngmtAgentTrap3058 | 1.3.6.1.4.1.232.0.136003058 | EM: Contents of the uploaded parse file invalid - unexpected contents | ||
| NTF mngmtAgentTrap3059 | 1.3.6.1.4.1.232.0.136003059 | EM: Parse file is empty | ||
| NTF mngmtAgentTrap3060 | 1.3.6.1.4.1.232.0.136003060 | Storage system being shutdown due to a command failure. | ||
| NTF mngmtAgentTrap3061 | 1.3.6.1.4.1.232.0.136003061 | EM: Could not retrieve a storage system event | ||
| NTF mngmtAgentTrap3062 | 1.3.6.1.4.1.232.0.136003062 | EM: Init SC Event config list failed | ||
| NTF mngmtAgentTrap3063 | 1.3.6.1.4.1.232.0.136003063 | Could not initialize Comm infrastructure for event logging to system log | ||
| NTF mngmtAgentTrap3064 | 1.3.6.1.4.1.232.0.136003064 | EM: Storage system pointer is NULL! | ||
| NTF mngmtAgentTrap3065 | 1.3.6.1.4.1.232.0.136003065 | EM: Failed to log event to the Appliance event log: check if log is full | ||
| NTF mngmtAgentTrap3066 | 1.3.6.1.4.1.232.0.136003066 | EM: Description Mngr initialize storage system failed | ||
| NTF mngmtAgentTrap3067 | 1.3.6.1.4.1.232.0.136003067 | EM: Description file too small. File read problem Or Incomplete file. | ||
| NTF mngmtAgentTrap3068 | 1.3.6.1.4.1.232.0.136003068 | EM: Can't init NT Event object pointer | ||
| NTF mngmtAgentTrap3069 | 1.3.6.1.4.1.232.0.136003069 | EM: Can't init NT Notification object pointer | ||
| NTF mngmtAgentTrap3070 | 1.3.6.1.4.1.232.0.136003070 | EM: Appliance Event Logging Failure - log may be full | ||
| NTF mngmtAgentTrap3071 | 1.3.6.1.4.1.232.0.136003071 | EM: SCMI returned bad additional events number | ||
| NTF mngmtAgentTrap3072 | 1.3.6.1.4.1.232.0.136003072 | EM: SCMI returned zero sized SC Event | ||
| NTF mngmtAgentTrap3075 | 1.3.6.1.4.1.232.0.136003075 | EventQueue index passed is out of bounds | ||
| NTF mngmtAgentTrap3076 | 1.3.6.1.4.1.232.0.136003076 | EM: An abnormal number of duplicate events logged - dropping duplicates | ||
| NTF mngmtAgentTrap3077 | 1.3.6.1.4.1.232.0.136003077 | EM: Update of the MLD Status Description file failed | ||
| NTF mngmtAgentTrap3078 | 1.3.6.1.4.1.232.0.136003078 | EM: NsaStatusDescriptions.txt open file error | ||
| NTF mngmtAgentTrap3079 | 1.3.6.1.4.1.232.0.136003079 | EM: NsaStatusDescriptions.txt file error - file size discrepancy from mld list | ||
| NTF mngmtAgentTrap3080 | 1.3.6.1.4.1.232.0.136003080 | SC Event Log has been cleared and restarted. Possible RAID1 Meltdown. | ||
| NTF mngmtAgentTrap3081 | 1.3.6.1.4.1.232.0.136003081 | Invalid logType parameter | ||
| NTF mngmtAgentTrap3083 | 1.3.6.1.4.1.232.0.136003083 | Log file is empty | ||
| NTF mngmtAgentTrap3084 | 1.3.6.1.4.1.232.0.136003084 | Storage System with this WWN is not visible to this agent or the WWN is invalid | ||
| NTF mngmtAgentTrap3086 | 1.3.6.1.4.1.232.0.136003086 | Parsefile for current firmware version not found. Upload correct parse file. | ||
| NTF mngmtAgentTrap3090 | 1.3.6.1.4.1.232.0.136003090 | The contents of this file appear to be invalid | ||
| NTF mngmtAgentTrap3091 | 1.3.6.1.4.1.232.0.136003091 | The MIB failed to build due to a missing parse file. | ||
| NTF mngmtAgentTrap3092 | 1.3.6.1.4.1.232.0.136003092 | MLD description file is older than local file but system is downrev | ||
| NTF mngmtAgentTrap3094 | 1.3.6.1.4.1.232.0.136003094 | System is initialized: can't get activeQ events | ||
| NTF mngmtAgentTrap3095 | 1.3.6.1.4.1.232.0.136003095 | Failed to write file - file could not be opened. | ||
| NTF mngmtAgentTrap4000 | 1.3.6.1.4.1.232.0.136004000 | MLD Manager Subsystem Error | ||
| NTF mngmtAgentTrap4001 | 1.3.6.1.4.1.232.0.136004001 | MLD Manager Offline | ||
| NTF mngmtAgentTrap4004 | 1.3.6.1.4.1.232.0.136004004 | MLD Manager Startup Complete | ||
| NTF mngmtAgentTrap4005 | 1.3.6.1.4.1.232.0.136004005 | MLD Manager Abnormal Startup | ||
| NTF mngmtAgentTrap4007 | 1.3.6.1.4.1.232.0.136004007 | MLD Manager Shutdown Complete | ||
| NTF mngmtAgentTrap4011 | 1.3.6.1.4.1.232.0.136004011 | Invalid Host IP Address specified | ||
| NTF mngmtAgentTrap4012 | 1.3.6.1.4.1.232.0.136004012 | Unable to open the NsaMldMgr.dat file for Write | ||
| NTF mngmtAgentTrap4013 | 1.3.6.1.4.1.232.0.136004013 | Unable to open the NsaMldMgr.dat file for Read | ||
| NTF mngmtAgentTrap4014 | 1.3.6.1.4.1.232.0.136004014 | Agent Uid does not exist | ||
| NTF mngmtAgentTrap4015 | 1.3.6.1.4.1.232.0.136004015 | Unable to find object | ||
| NTF mngmtAgentTrap4016 | 1.3.6.1.4.1.232.0.136004016 | Unable to store object | ||
| NTF mngmtAgentTrap4017 | 1.3.6.1.4.1.232.0.136004017 | Unable to find storage system object | ||
| NTF mngmtAgentTrap4018 | 1.3.6.1.4.1.232.0.136004018 | Unable to create MLD | ||
| NTF mngmtAgentTrap4020 | 1.3.6.1.4.1.232.0.136004020 | lastSafeChoiceDelay Expired | ||
| NTF mngmtAgentTrap4021 | 1.3.6.1.4.1.232.0.136004021 | crashDetectDelay Expired | ||
| NTF mngmtAgentTrap4023 | 1.3.6.1.4.1.232.0.136004023 | Unable to read Copy1 of MLD | ||
| NTF mngmtAgentTrap4024 | 1.3.6.1.4.1.232.0.136004024 | Copy 1 of MLD Invalid | ||
| NTF mngmtAgentTrap4025 | 1.3.6.1.4.1.232.0.136004025 | Invalid Copy block of MLD | ||
| NTF mngmtAgentTrap4027 | 1.3.6.1.4.1.232.0.136004027 | MLD database capacity not equal to true MLD capacity | ||
| NTF mngmtAgentTrap4028 | 1.3.6.1.4.1.232.0.136004028 | Backup range out of bounds of copy 1 range | ||
| NTF mngmtAgentTrap4029 | 1.3.6.1.4.1.232.0.136004029 | MLD Manager Lock Crash DetectDelay has expired, just taking lock! | ||
| NTF mngmtAgentTrap4030 | 1.3.6.1.4.1.232.0.136004030 | MLD Copy 1 Restored | ||
| NTF mngmtAgentTrap4031 | 1.3.6.1.4.1.232.0.136004031 | MLD Copy 2 Restored | ||
| NTF mngmtAgentTrap4032 | 1.3.6.1.4.1.232.0.136004032 | Unable to find UidAssoc Object | ||
| NTF mngmtAgentTrap4033 | 1.3.6.1.4.1.232.0.136004033 | Unable to store UID Association Object | ||
| NTF mngmtAgentTrap4034 | 1.3.6.1.4.1.232.0.136004034 | Unable to find UidAssoc Object | ||
| NTF mngmtAgentTrap4035 | 1.3.6.1.4.1.232.0.136004035 | Unable to read last Fusion event read | ||
| NTF mngmtAgentTrap4036 | 1.3.6.1.4.1.232.0.136004036 | MLD Notification Queue Empty | ||
| NTF mngmtAgentTrap4037 | 1.3.6.1.4.1.232.0.136004037 | Unable to find Notification Object | ||
| NTF mngmtAgentTrap4040 | 1.3.6.1.4.1.232.0.136004040 | Unable to read Event Log Pointer | ||
| NTF mngmtAgentTrap4041 | 1.3.6.1.4.1.232.0.136004041 | Unable to read Event Log | ||
| NTF mngmtAgentTrap4042 | 1.3.6.1.4.1.232.0.136004042 | Unable to store Event Log | ||
| NTF mngmtAgentTrap4043 | 1.3.6.1.4.1.232.0.136004043 | Unable to read Event Log | ||
| NTF mngmtAgentTrap4047 | 1.3.6.1.4.1.232.0.136004047 | Previously Read Object Properties do not Match | ||
| NTF mngmtAgentTrap4048 | 1.3.6.1.4.1.232.0.136004048 | Previously Read Object Properties do not Match | ||
| NTF mngmtAgentTrap4049 | 1.3.6.1.4.1.232.0.136004049 | Unable to read Notification Host List | ||
| NTF mngmtAgentTrap4050 | 1.3.6.1.4.1.232.0.136004050 | Unable to store Notification Host List | ||
| NTF mngmtAgentTrap4051 | 1.3.6.1.4.1.232.0.136004051 | Unable to store Notification Host List and free Lock | ||
| NTF mngmtAgentTrap4052 | 1.3.6.1.4.1.232.0.136004052 | Unable to read Event Configuration List | ||
| NTF mngmtAgentTrap4053 | 1.3.6.1.4.1.232.0.136004053 | Unable to store Event Configuration List | ||
| NTF mngmtAgentTrap4054 | 1.3.6.1.4.1.232.0.136004054 | Unable to store Event Configuration List and free Lock | ||
| NTF mngmtAgentTrap4058 | 1.3.6.1.4.1.232.0.136004058 | MLD Manager Mutex Timeout error | ||
| NTF mngmtAgentTrap4059 | 1.3.6.1.4.1.232.0.136004059 | MLD Manager list is empty | ||
| NTF mngmtAgentTrap5001 | 1.3.6.1.4.1.232.0.136005001 | Monitor Startup Complete | ||
| NTF mngmtAgentTrap5002 | 1.3.6.1.4.1.232.0.136005002 | Monitor Startup Failed | ||
| NTF mngmtAgentTrap5003 | 1.3.6.1.4.1.232.0.136005003 | Monitor ShutDown Complete | ||
| NTF mngmtAgentTrap5004 | 1.3.6.1.4.1.232.0.136005004 | Monitor Memory Allocation Failure | ||
| NTF mngmtAgentTrap5005 | 1.3.6.1.4.1.232.0.136005005 | Monitor Mark Agent as Inactive | ||
| NTF mngmtAgentTrap5006 | 1.3.6.1.4.1.232.0.136005006 | Monitor create thread error | ||
| NTF mngmtAgentTrap5007 | 1.3.6.1.4.1.232.0.136005007 | Monitor create timer error | ||
| NTF mngmtAgentTrap5008 | 1.3.6.1.4.1.232.0.136005008 | Monitor agent registration - Complete | ||
| NTF mngmtAgentTrap5010 | 1.3.6.1.4.1.232.0.136005010 | Monitor initiated a storage system management shutdown because of controller failures | ||
| NTF mngmtAgentTrap5011 | 1.3.6.1.4.1.232.0.136005011 | Unknown storage system rediscovery complete | ||
| NTF mngmtAgentTrap5012 | 1.3.6.1.4.1.232.0.136005012 | Start monitoring thread for storage system - Complete | ||
| NTF mngmtAgentTrap5013 | 1.3.6.1.4.1.232.0.136005013 | Start monitoring thread for storage system - Fail | ||
| NTF mngmtAgentTrap5014 | 1.3.6.1.4.1.232.0.136005014 | Monitoring thread for storage system terminated | ||
| NTF mngmtAgentTrap5015 | 1.3.6.1.4.1.232.0.136005015 | Rediscover unknown storage system - Error | ||
| NTF mngmtAgentTrap5016 | 1.3.6.1.4.1.232.0.136005016 | Controller time synchronized to appliance time. | ||
| NTF mngmtAgentTrap5017 | 1.3.6.1.4.1.232.0.136005017 | Appliance and controller time checked for synchronization. | ||
| NTF mngmtAgentTrap5018 | 1.3.6.1.4.1.232.0.136005018 | Controller and appliance time are the same. No need to synchronize. | ||
| NTF mngmtAgentTrap5019 | 1.3.6.1.4.1.232.0.136005019 | Exception caught in monitoring process. | ||
| NTF mngmtAgentTrap6001 | 1.3.6.1.4.1.232.0.136006001 | Ready | ||
| NTF mngmtAgentTrap6002 | 1.3.6.1.4.1.232.0.136006002 | Index Out of Range | ||
| NTF mngmtAgentTrap6003 | 1.3.6.1.4.1.232.0.136006003 | Cannot access storage system. Communications error. | ||
| NTF mngmtAgentTrap6004 | 1.3.6.1.4.1.232.0.136006004 | No controllers found | ||
| NTF mngmtAgentTrap6005 | 1.3.6.1.4.1.232.0.136006005 | Invalid Index | ||
| NTF mngmtAgentTrap6006 | 1.3.6.1.4.1.232.0.136006006 | Memory allocation failure | ||
| NTF mngmtAgentTrap6007 | 1.3.6.1.4.1.232.0.136006007 | No physical stores found | ||
| NTF mngmtAgentTrap6008 | 1.3.6.1.4.1.232.0.136006008 | No storage system found | ||
| NTF mngmtAgentTrap6009 | 1.3.6.1.4.1.232.0.136006009 | No disk group found | ||
| NTF mngmtAgentTrap6010 | 1.3.6.1.4.1.232.0.136006010 | Too many disk groups | ||
| NTF mngmtAgentTrap6011 | 1.3.6.1.4.1.232.0.136006011 | No volumes found | ||
| NTF mngmtAgentTrap6012 | 1.3.6.1.4.1.232.0.136006012 | No Logical Disks Found | ||
| NTF mngmtAgentTrap6013 | 1.3.6.1.4.1.232.0.136006013 | Context ID changed during operation | ||
| NTF mngmtAgentTrap6014 | 1.3.6.1.4.1.232.0.136006014 | No Name | ||
| NTF mngmtAgentTrap6015 | 1.3.6.1.4.1.232.0.136006015 | Name Size Exceeded | ||
| NTF mngmtAgentTrap6016 | 1.3.6.1.4.1.232.0.136006016 | Shutdown Complete | ||
| NTF mngmtAgentTrap6017 | 1.3.6.1.4.1.232.0.136006017 | Mutex Creation Failure | ||
| NTF mngmtAgentTrap6018 | 1.3.6.1.4.1.232.0.136006018 | The command has timed out. Storage system is busy processing previous command. | ||
| NTF mngmtAgentTrap6019 | 1.3.6.1.4.1.232.0.136006019 | No MLD Handle Set | ||
| NTF mngmtAgentTrap6020 | 1.3.6.1.4.1.232.0.136006020 | Failed Transport Layer Communication - No Such Id | ||
| NTF mngmtAgentTrap6021 | 1.3.6.1.4.1.232.0.136006021 | Failed Transport Layer Communication - TimeOut | ||
| NTF mngmtAgentTrap6022 | 1.3.6.1.4.1.232.0.136006022 | No initialized storage system objects found | ||
| NTF mngmtAgentTrap6023 | 1.3.6.1.4.1.232.0.136006023 | No Attached Port Found | ||
| NTF mngmtAgentTrap6024 | 1.3.6.1.4.1.232.0.136006024 | Failed to get SCMI Object Handle | ||
| NTF mngmtAgentTrap6025 | 1.3.6.1.4.1.232.0.136006025 | Shutdown Both Restart And Power Off Requested | ||
| NTF mngmtAgentTrap6026 | 1.3.6.1.4.1.232.0.136006026 | Shutdown Drive Shelf Power Off But No Enclosure Power Off Requested | ||
| NTF mngmtAgentTrap6027 | 1.3.6.1.4.1.232.0.136006027 | Shutdown Disable Battery But No Enclosure Power Off Requested | ||
| NTF mngmtAgentTrap6028 | 1.3.6.1.4.1.232.0.136006028 | Shutdown Disable Battery But Shutdown Unconditional Requested | ||
| NTF mngmtAgentTrap6029 | 1.3.6.1.4.1.232.0.136006029 | Shutdown Delay Out Of Range | ||
| NTF mngmtAgentTrap6030 | 1.3.6.1.4.1.232.0.136006030 | Cache Write Failure | ||
| NTF mngmtAgentTrap6031 | 1.3.6.1.4.1.232.0.136006031 | Battery Disable Failure | ||
| NTF mngmtAgentTrap6032 | 1.3.6.1.4.1.232.0.136006032 | Drive Shelf Disable Failure | ||
| NTF mngmtAgentTrap6033 | 1.3.6.1.4.1.232.0.136006033 | Battery Disable Failed on Both Controllers Batteries | ||
| NTF mngmtAgentTrap6034 | 1.3.6.1.4.1.232.0.136006034 | Battery Disable Failed on This Controllers Battery | ||
| NTF mngmtAgentTrap6035 | 1.3.6.1.4.1.232.0.136006035 | Battery Disable Failed on the Other Controllers Battery | ||
| NTF mngmtAgentTrap6036 | 1.3.6.1.4.1.232.0.136006036 | Requested disk failure protection level is set. Actual level will change when sufficient disk space is available. | ||
| NTF mngmtAgentTrap6037 | 1.3.6.1.4.1.232.0.136006037 | Physical Store Contains Stale or Foreign Volume Information. | ||
| NTF mngmtAgentTrap6038 | 1.3.6.1.4.1.232.0.136006038 | Controller Resynchronization or Reboot Occurred. Context Error | ||
| NTF mngmtAgentTrap8001 | 1.3.6.1.4.1.232.0.136008001 | Invalid Operation | ||
| NTF mngmtAgentTrap8002 | 1.3.6.1.4.1.232.0.136008002 | Storage system already created | ||
| NTF mngmtAgentTrap8003 | 1.3.6.1.4.1.232.0.136008003 | Controller already part of storage system configuration | ||
| NTF mngmtAgentTrap8004 | 1.3.6.1.4.1.232.0.136008004 | Physical Store Count Below Minimum | ||
| NTF mngmtAgentTrap8005 | 1.3.6.1.4.1.232.0.136008005 | Controller not part of storage system configuration | ||
| NTF mngmtAgentTrap8006 | 1.3.6.1.4.1.232.0.136008006 | Failed to uninitialize storage system | ||
| NTF mngmtAgentTrap8007 | 1.3.6.1.4.1.232.0.136008007 | Storage system File Open Error | ||
| NTF mngmtAgentTrap8008 | 1.3.6.1.4.1.232.0.136008008 | Storage system File Write Error | ||
| NTF mngmtAgentTrap8009 | 1.3.6.1.4.1.232.0.136008009 | Storage system File Read Error | ||
| NTF mngmtAgentTrap8010 | 1.3.6.1.4.1.232.0.136008010 | Name too long | ||
| NTF mngmtAgentTrap8011 | 1.3.6.1.4.1.232.0.136008011 | No String Error | ||
| NTF mngmtAgentTrap8012 | 1.3.6.1.4.1.232.0.136008012 | No MLD Handle Found | ||
| NTF mngmtAgentTrap8013 | 1.3.6.1.4.1.232.0.136008013 | No Controllers Found | ||
| NTF mngmtAgentTrap8014 | 1.3.6.1.4.1.232.0.136008014 | Controller Not Found On Loop | ||
| NTF mngmtAgentTrap8015 | 1.3.6.1.4.1.232.0.136008015 | No Disk Groups Found | ||
| NTF mngmtAgentTrap8016 | 1.3.6.1.4.1.232.0.136008016 | No Volumes Found | ||
| NTF mngmtAgentTrap8017 | 1.3.6.1.4.1.232.0.136008017 | No Physical Stores Found | ||
| NTF mngmtAgentTrap8018 | 1.3.6.1.4.1.232.0.136008018 | No Vdisks Found | ||
| NTF mngmtAgentTrap8019 | 1.3.6.1.4.1.232.0.136008019 | No Hosts Found | ||
| NTF mngmtAgentTrap8020 | 1.3.6.1.4.1.232.0.136008020 | Name already exists | ||
| NTF mngmtAgentTrap8021 | 1.3.6.1.4.1.232.0.136008021 | Folder is not empty | ||
| NTF mngmtAgentTrap8022 | 1.3.6.1.4.1.232.0.136008022 | Spares goal could not be met | ||
| NTF mngmtAgentTrap8023 | 1.3.6.1.4.1.232.0.136008023 | Storage system object found | ||
| NTF mngmtAgentTrap8024 | 1.3.6.1.4.1.232.0.136008024 | Storage system object not found | ||
| NTF mngmtAgentTrap8025 | 1.3.6.1.4.1.232.0.136008025 | New Physical Store Detected But Not Found In Physical Store List | ||
| NTF mngmtAgentTrap8026 | 1.3.6.1.4.1.232.0.136008026 | MldManager Handle is NULL | ||
| NTF mngmtAgentTrap8027 | 1.3.6.1.4.1.232.0.136008027 | NscMngrInterface Handle is NULL | ||
| NTF mngmtAgentTrap8028 | 1.3.6.1.4.1.232.0.136008028 | ScLockMngr Handle is NULL | ||
| NTF mngmtAgentTrap8029 | 1.3.6.1.4.1.232.0.136008029 | Storage system initialization failed | ||
| NTF mngmtAgentTrap8030 | 1.3.6.1.4.1.232.0.136008030 | MldMngr, NscMngrInterfaceMngr, or ScLockMngr Handle is NULL | ||
| NTF mngmtAgentTrap8031 | 1.3.6.1.4.1.232.0.136008031 | Storage system initialization failed | ||
| NTF mngmtAgentTrap8032 | 1.3.6.1.4.1.232.0.136008032 | Storage system discovery failed | ||
| NTF mngmtAgentTrap8033 | 1.3.6.1.4.1.232.0.136008033 | Storage system already uninitialized or does not exist | ||
| NTF mngmtAgentTrap8034 | 1.3.6.1.4.1.232.0.136008034 | Get Total Storage Failed | ||
| NTF mngmtAgentTrap8035 | 1.3.6.1.4.1.232.0.136008035 | Storage system is uninitialized | ||
| NTF mngmtAgentTrap8036 | 1.3.6.1.4.1.232.0.136008036 | Get Total Storage Available Failed | ||
| NTF mngmtAgentTrap8037 | 1.3.6.1.4.1.232.0.136008037 | Get Total Storage Occupied Failed | ||
| NTF mngmtAgentTrap8038 | 1.3.6.1.4.1.232.0.136008038 | Get Total Storage Free Failed | ||
| NTF mngmtAgentTrap8039 | 1.3.6.1.4.1.232.0.136008039 | Get Disk Group Failed | ||
| NTF mngmtAgentTrap8040 | 1.3.6.1.4.1.232.0.136008040 | Get Disk Group List Failed | ||
| NTF mngmtAgentTrap8041 | 1.3.6.1.4.1.232.0.136008041 | Get Disk Group Count Failed | ||
| NTF mngmtAgentTrap8042 | 1.3.6.1.4.1.232.0.136008042 | Create Volume Failed | ||
| NTF mngmtAgentTrap8043 | 1.3.6.1.4.1.232.0.136008043 | Get Volume Failed | ||
| NTF mngmtAgentTrap8044 | 1.3.6.1.4.1.232.0.136008044 | Get Volumes Failed | ||
| NTF mngmtAgentTrap8045 | 1.3.6.1.4.1.232.0.136008045 | Get Volumes Count Failed | ||
| NTF mngmtAgentTrap8046 | 1.3.6.1.4.1.232.0.136008046 | Get Vdisk Failed | ||
| NTF mngmtAgentTrap8047 | 1.3.6.1.4.1.232.0.136008047 | Get Vdisk List Failed | ||
| NTF mngmtAgentTrap8048 | 1.3.6.1.4.1.232.0.136008048 | Get Physical Store Failed | ||
| NTF mngmtAgentTrap8049 | 1.3.6.1.4.1.232.0.136008049 | Get Physical Stores Failed | ||
| NTF mngmtAgentTrap8050 | 1.3.6.1.4.1.232.0.136008050 | Get Physical Stores Count Failed | ||
| NTF mngmtAgentTrap8051 | 1.3.6.1.4.1.232.0.136008051 | Create Vdisk Failed | ||
| NTF mngmtAgentTrap8052 | 1.3.6.1.4.1.232.0.136008052 | Delete Vdisk Failed | ||
| NTF mngmtAgentTrap8053 | 1.3.6.1.4.1.232.0.136008053 | Get Device Addition Policy Failed | ||
| NTF mngmtAgentTrap8054 | 1.3.6.1.4.1.232.0.136008054 | Get Spares Current Failed | ||
| NTF mngmtAgentTrap8055 | 1.3.6.1.4.1.232.0.136008055 | Get Spares Goal Failed | ||
| NTF mngmtAgentTrap8056 | 1.3.6.1.4.1.232.0.136008056 | Get storage system events failed | ||
| NTF mngmtAgentTrap8057 | 1.3.6.1.4.1.232.0.136008057 | Get Volume Replacement Delay Failed | ||
| NTF mngmtAgentTrap8058 | 1.3.6.1.4.1.232.0.136008058 | Set Device Addition Policy Failed | ||
| NTF mngmtAgentTrap8059 | 1.3.6.1.4.1.232.0.136008059 | Set Spares Goal Failed | ||
| NTF mngmtAgentTrap8060 | 1.3.6.1.4.1.232.0.136008060 | Set Volume Replacement Delay Failed | ||
| NTF mngmtAgentTrap8061 | 1.3.6.1.4.1.232.0.136008061 | Create controller Failed | ||
| NTF mngmtAgentTrap8062 | 1.3.6.1.4.1.232.0.136008062 | Update controller Failed | ||
| NTF mngmtAgentTrap8063 | 1.3.6.1.4.1.232.0.136008063 | Create Host Failed | ||
| NTF mngmtAgentTrap8064 | 1.3.6.1.4.1.232.0.136008064 | Discard Host Failed | ||
| NTF mngmtAgentTrap8065 | 1.3.6.1.4.1.232.0.136008065 | Get Host Failed | ||
| NTF mngmtAgentTrap8066 | 1.3.6.1.4.1.232.0.136008066 | Get Host List Failed | ||
| NTF mngmtAgentTrap8067 | 1.3.6.1.4.1.232.0.136008067 | Get Host Count Failed | ||
| NTF mngmtAgentTrap8068 | 1.3.6.1.4.1.232.0.136008068 | Get Presented Unit List Failed | ||
| NTF mngmtAgentTrap8069 | 1.3.6.1.4.1.232.0.136008069 | Get Presented Unit Count Failed | ||
| NTF mngmtAgentTrap8070 | 1.3.6.1.4.1.232.0.136008070 | Free View Failed | ||
| NTF mngmtAgentTrap8071 | 1.3.6.1.4.1.232.0.136008071 | Storage system shutdown Failed | ||
| NTF mngmtAgentTrap8073 | 1.3.6.1.4.1.232.0.136008073 | Get Derived Unit List Failed | ||
| NTF mngmtAgentTrap8074 | 1.3.6.1.4.1.232.0.136008074 | Get Derived Unit Count Failed | ||
| NTF mngmtAgentTrap8075 | 1.3.6.1.4.1.232.0.136008075 | Get Vdisk list failed | ||
| NTF mngmtAgentTrap8076 | 1.3.6.1.4.1.232.0.136008076 | Get Vdisk count failed | ||
| NTF mngmtAgentTrap8077 | 1.3.6.1.4.1.232.0.136008077 | Error while building Vdisk root view | ||
| NTF mngmtAgentTrap8078 | 1.3.6.1.4.1.232.0.136008078 | Error while building host root view | ||
| NTF mngmtAgentTrap8079 | 1.3.6.1.4.1.232.0.136008079 | Error while building disk group root view | ||
| NTF mngmtAgentTrap8080 | 1.3.6.1.4.1.232.0.136008080 | Error while building hardware root view | ||
| NTF mngmtAgentTrap8081 | 1.3.6.1.4.1.232.0.136008081 | Specified time format is incorrect | ||
| NTF mngmtAgentTrap8082 | 1.3.6.1.4.1.232.0.136008082 | Error creating/opening time synchronization file. | ||
| NTF mngmtAgentTrap8083 | 1.3.6.1.4.1.232.0.136008083 | NSCList reordered. | ||
| NTF mngmtAgentTrap8084 | 1.3.6.1.4.1.232.0.136008084 | NscList mutex Get error | ||
| NTF mngmtAgentTrap8085 | 1.3.6.1.4.1.232.0.136008085 | Storage System is managed by another agent | ||
| NTF mngmtAgentTrap8086 | 1.3.6.1.4.1.232.0.136008086 | Memory allocation failure | ||
| NTF mngmtAgentTrap8087 | 1.3.6.1.4.1.232.0.136008087 | Failed to obtain list of DR Groups | ||
| NTF mngmtAgentTrap8088 | 1.3.6.1.4.1.232.0.136008088 | Failed to obtain count of DR Groups | ||
| NTF mngmtAgentTrap8089 | 1.3.6.1.4.1.232.0.136008089 | Failed to build DR Group view | ||
| NTF mngmtAgentTrap8090 | 1.3.6.1.4.1.232.0.136008090 | No Devices found on Controller Back End Loops | ||
| NTF mngmtAgentTrap9001 | 1.3.6.1.4.1.232.0.136009001 | Vdisk File Open Error | ||
| NTF mngmtAgentTrap9002 | 1.3.6.1.4.1.232.0.136009002 | Vdisk File Write Error | ||
| NTF mngmtAgentTrap9003 | 1.3.6.1.4.1.232.0.136009003 | Vdisk File Read Error | ||
| NTF mngmtAgentTrap9004 | 1.3.6.1.4.1.232.0.136009004 | Vdisk name too long | ||
| NTF mngmtAgentTrap9005 | 1.3.6.1.4.1.232.0.136009005 | Vdisk No String Error | ||
| NTF mngmtAgentTrap9006 | 1.3.6.1.4.1.232.0.136009006 | Vdisk No Object Error | ||
| NTF mngmtAgentTrap9007 | 1.3.6.1.4.1.232.0.136009007 | Vdisk still exists | ||
| NTF mngmtAgentTrap9008 | 1.3.6.1.4.1.232.0.136009008 | Vdisk Invalid Value | ||
| NTF mngmtAgentTrap9009 | 1.3.6.1.4.1.232.0.136009009 | An outstanding command is still in progress for the Vdisk | ||
| NTF mngmtAgentTrap9010 | 1.3.6.1.4.1.232.0.136009010 | Requested Vdisk size exceeds the available size | ||
| NTF mngmtAgentTrap9011 | 1.3.6.1.4.1.232.0.136009011 | Vdisk size may be expanded but not reduced | ||
| NTF mngmtAgentTrap9012 | 1.3.6.1.4.1.232.0.136009012 | Operation on a fast Vdisk deletion completed | ||
| NTF mngmtAgentTrap9013 | 1.3.6.1.4.1.232.0.136009013 | Operation on a fast Vdisk creation completed | ||
| NTF mngmtAgentTrap9014 | 1.3.6.1.4.1.232.0.136009014 | Operation on a fast Vdisk size expansion completed | ||
| NTF mngmtAgentTrap9015 | 1.3.6.1.4.1.232.0.136009015 | Vdisk cache data lost error | ||
| NTF mngmtAgentTrap9016 | 1.3.6.1.4.1.232.0.136009016 | Vdisk data lost error resolved | ||
| NTF mngmtAgentTrap9017 | 1.3.6.1.4.1.232.0.136009017 | Operation rejected - The Vdisk has a sharing relationship with another object | ||
| NTF mngmtAgentTrap9018 | 1.3.6.1.4.1.232.0.136009018 | Operation on this Vdisk was rejected due to its degraded condition | ||
| NTF mngmtAgentTrap9019 | 1.3.6.1.4.1.232.0.136009019 | Operation on this Vdisk can only be performed if it is presented to a host | ||
| NTF mngmtAgentTrap9020 | 1.3.6.1.4.1.232.0.136009020 | Cache policies cannot be modified if Vdisk is presented to a host | ||
| NTF mngmtAgentTrap9021 | 1.3.6.1.4.1.232.0.136009021 | Allowed property changes successful. (Cache policy changes not allowed while Vdisk is presented to a host.) | ||
| NTF mngmtAgentTrap9022 | 1.3.6.1.4.1.232.0.136009022 | Requested redundancy type cannot be implemented with the current disk group condition. | ||
| NTF mngmtAgentTrap9023 | 1.3.6.1.4.1.232.0.136009023 | Your Vdisk was created but cannot be presented at this time. It can be presented when it is fully allocated. | ||
| NTF mngmtAgentTrap9025 | 1.3.6.1.4.1.232.0.136009025 | Vdisk device data lost error | ||
| NTF mngmtAgentTrap9026 | 1.3.6.1.4.1.232.0.136009026 | The most significant hex character in a World Wide LUN Name must be a 6. | ||
| NTF mngmtAgentTrap9027 | 1.3.6.1.4.1.232.0.136009027 | Virtual disk cache and inoperative data lost error | ||
| NTF mngmtAgentTrap9028 | 1.3.6.1.4.1.232.0.136009028 | Virtual disk inoperative data lost error | ||
| NTF mngmtAgentTrap9029 | 1.3.6.1.4.1.232.0.136009029 | Virtual disk condition failed because of an inoperative data lost error. | ||
| NTF mngmtAgentTrap9030 | 1.3.6.1.4.1.232.0.136009030 | Vdisk is a snapshot. The following properties cannot be changed: Preferred Path, Requested Size, Write-Back Cache Policy. | ||
| NTF mngmtAgentTrap9031 | 1.3.6.1.4.1.232.0.136009031 | The World Wide LUN Name cannot be changed for a presented Vdisk Active member or snapshot. | ||
| NTF mngmtAgentTrap9032 | 1.3.6.1.4.1.232.0.136009032 | Unknown property, request rejected | ||
| NTF mngmtAgentTrap9033 | 1.3.6.1.4.1.232.0.136009033 | This Vdisk was deleted as the indirect result of another user command. | ||
| NTF mngmtAgentTrap9034 | 1.3.6.1.4.1.232.0.136009034 | The requested allocation policy cannot be satisfied. A different allocation policy is already in use by another snapshot in the same family. | ||
| NTF mngmtAgentTrap9035 | 1.3.6.1.4.1.232.0.136009035 | The deletion of this Vdisk cannot take place. The original Vdisk that this is being snapcloned from is in a VRaid1 Meltdown state which must first be resolved. | ||
| NTF mngmtAgentTrap9036 | 1.3.6.1.4.1.232.0.136009036 | Synchronous creation of virtual disk has been aborted due to an internal error. Switching to asynchronous mode to complete the virtual disk creation. | ||
| NTF mngmtAgentTrap10001 | 1.3.6.1.4.1.232.0.136010001 | Storage Object Broker Ready | ||
| NTF mngmtAgentTrap10004 | 1.3.6.1.4.1.232.0.136010004 | Storage system is not initialized | ||
| NTF mngmtAgentTrap10006 | 1.3.6.1.4.1.232.0.136010006 | SOB Memory Allocation Failure | ||
| NTF mngmtAgentTrap10010 | 1.3.6.1.4.1.232.0.136010010 | Your initialized system must have at least one disk group | ||
| NTF mngmtAgentTrap10011 | 1.3.6.1.4.1.232.0.136010011 | Cannot talk to all available controllers | ||
| NTF mngmtAgentTrap10012 | 1.3.6.1.4.1.232.0.136010012 | Command rejected - Folder is not empty | ||
| NTF mngmtAgentTrap10013 | 1.3.6.1.4.1.232.0.136010013 | Command rejected - Vdisk(s) or a data replication log are contained in this disk group | ||
| NTF mngmtAgentTrap10014 | 1.3.6.1.4.1.232.0.136010014 | Command rejected - Vdisk(s) are presented to this host | ||
| NTF mngmtAgentTrap10015 | 1.3.6.1.4.1.232.0.136010015 | Command rejected - This Vdisk has a sharing relationship with another object | ||
| NTF mngmtAgentTrap10017 | 1.3.6.1.4.1.232.0.136010017 | Command rejected - Number of disk groups will exceed the maximum allowable number | ||
| NTF mngmtAgentTrap10018 | 1.3.6.1.4.1.232.0.136010018 | Cannot access the password file | ||
| NTF mngmtAgentTrap10019 | 1.3.6.1.4.1.232.0.136010019 | Enterprise Login - Complete | ||
| NTF mngmtAgentTrap10020 | 1.3.6.1.4.1.232.0.136010020 | Command rejected - Disks in the group would go below the minimum required number. | ||
| NTF mngmtAgentTrap10021 | 1.3.6.1.4.1.232.0.136010021 | Rediscovery of controllers - Complete | ||
| NTF mngmtAgentTrap10022 | 1.3.6.1.4.1.232.0.136010022 | Unable to establish communication with controller, check all connections. | ||
| NTF mngmtAgentTrap10023 | 1.3.6.1.4.1.232.0.136010023 | Disk Group Data Lost Error Resolution Sequence 3 - Disk group resolved to normal | ||
| NTF mngmtAgentTrap10024 | 1.3.6.1.4.1.232.0.136010024 | Disk Group Data Lost Error Resolution Sequence 1 - Failed Vdisks marked for deletion | ||
| NTF mngmtAgentTrap10025 | 1.3.6.1.4.1.232.0.136010025 | Disk Group Data Lost Error Resolution Sequence 2 - Failed Vdisks deleted | ||
| NTF mngmtAgentTrap10026 | 1.3.6.1.4.1.232.0.136010026 | Disk Group Data Lost Error Resolution Sequence 3 - Disk group deleted | ||
| NTF mngmtAgentTrap10027 | 1.3.6.1.4.1.232.0.136010027 | Creating the Vdisk would exceed the maximum allowable Vdisk count | ||
| NTF mngmtAgentTrap10028 | 1.3.6.1.4.1.232.0.136010028 | Volume insufficient resources | ||
| NTF mngmtAgentTrap10029 | 1.3.6.1.4.1.232.0.136010029 | Process mutex is locked | ||
| NTF mngmtAgentTrap10030 | 1.3.6.1.4.1.232.0.136010030 | Invalid URL request type | ||
| NTF mngmtAgentTrap10031 | 1.3.6.1.4.1.232.0.136010031 | Invalid URL object type | ||
| NTF mngmtAgentTrap10035 | 1.3.6.1.4.1.232.0.136010035 | The snapshot/Snapclone license cannot be validated. Either the license key has not been entered, or there is a system communication failure. | ||
| NTF mngmtAgentTrap10036 | 1.3.6.1.4.1.232.0.136010036 | A data replication license cannot be validated. Either the license key has not been entered, or there is a system communication failure. | ||
| NTF mngmtAgentTrap10037 | 1.3.6.1.4.1.232.0.136010037 | Object name should not be empty or exceed its maximum length | ||
| NTF mngmtAgentTrap10038 | 1.3.6.1.4.1.232.0.136010038 | Object comments exceeds maximum length | ||
| NTF mngmtAgentTrap10039 | 1.3.6.1.4.1.232.0.136010039 | Vdisk does not meet the requirements to be part of a DR group. | ||
| NTF mngmtAgentTrap10040 | 1.3.6.1.4.1.232.0.136010040 | The Eva selected as the Destination for the DR group is invalid. Either it has a DR relationship with another EVA or it is not the same EVA that the source EVA presently has a DR relationship with. | ||
| NTF mngmtAgentTrap10041 | 1.3.6.1.4.1.232.0.136010041 | Cannot group the specified disk device because the disk is already in a disk group. | ||
| NTF mngmtAgentTrap10042 | 1.3.6.1.4.1.232.0.136010042 | Cannot ungroup the specified disk device because the disk is not grouped. | ||
| NTF mngmtAgentTrap10043 | 1.3.6.1.4.1.232.0.136010043 | Object ID provided, or object type, is invalid for the requested operation. | ||
| NTF mngmtAgentTrap10044 | 1.3.6.1.4.1.232.0.136010044 | Specified remote disk group does not exist. | ||
| NTF mngmtAgentTrap11001 | 1.3.6.1.4.1.232.0.136011001 | Agent startup complete | ||
| NTF mngmtAgentTrap11002 | 1.3.6.1.4.1.232.0.136011002 | Agent shutdown complete | ||
| NTF mngmtAgentTrap11003 | 1.3.6.1.4.1.232.0.136011003 | Insufficient memory to create a new object, Heap may be full! | ||
| NTF mngmtAgentTrap11004 | 1.3.6.1.4.1.232.0.136011004 | Agent Startup Failed | ||
| NTF mngmtAgentTrap12001 | 1.3.6.1.4.1.232.0.136012001 | Nsc Manager Interface No controllers Found | ||
| NTF mngmtAgentTrap12002 | 1.3.6.1.4.1.232.0.136012002 | Nsc Manager Interface Index Out Of Range | ||
| NTF mngmtAgentTrap12003 | 1.3.6.1.4.1.232.0.136012003 | Unable to process command at this time. Retry the command or check all connections. | ||
| NTF mngmtAgentTrap12004 | 1.3.6.1.4.1.232.0.136012004 | Nsc Manager Interface Initialization Complete | ||
| NTF mngmtAgentTrap12005 | 1.3.6.1.4.1.232.0.136012005 | Nsc Manager Interface Initialization Failed | ||
| NTF mngmtAgentTrap12008 | 1.3.6.1.4.1.232.0.136012008 | No Disk Groups Available For Access | ||
| NTF mngmtAgentTrap13002 | 1.3.6.1.4.1.232.0.136013002 | Notification Mngr Online | ||
| NTF mngmtAgentTrap13003 | 1.3.6.1.4.1.232.0.136013003 | Notification Mngr Offline | ||
| NTF mngmtAgentTrap13004 | 1.3.6.1.4.1.232.0.136013004 | NM Startup Complete | ||
| NTF mngmtAgentTrap13007 | 1.3.6.1.4.1.232.0.136013007 | Notification Failed | ||
| NTF mngmtAgentTrap13009 | 1.3.6.1.4.1.232.0.136013009 | Notification Failed - Network Error | ||
| NTF mngmtAgentTrap13012 | 1.3.6.1.4.1.232.0.136013012 | NM Prev Failed Notification Successfully Notified | ||
| NTF mngmtAgentTrap13015 | 1.3.6.1.4.1.232.0.136013015 | NM SNMP Packet Failed | ||
| NTF mngmtAgentTrap13017 | 1.3.6.1.4.1.232.0.136013017 | NM Memory Allocation Error | ||
| NTF mngmtAgentTrap13018 | 1.3.6.1.4.1.232.0.136013018 | NM StorageCell handle is NULL | ||
| NTF mngmtAgentTrap13019 | 1.3.6.1.4.1.232.0.136013019 | NM User defined event state file is empty | ||
| NTF mngmtAgentTrap13020 | 1.3.6.1.4.1.232.0.136013020 | NM Notification Failed - Notification Matrix is NULL | ||
| NTF mngmtAgentTrap14001 | 1.3.6.1.4.1.232.0.136014001 | View Already Exists | ||
| NTF mngmtAgentTrap14002 | 1.3.6.1.4.1.232.0.136014002 | View Is Not Set | ||
| NTF mngmtAgentTrap14003 | 1.3.6.1.4.1.232.0.136014003 | No View Object(s) Found | ||
| NTF mngmtAgentTrap14004 | 1.3.6.1.4.1.232.0.136014004 | View Index Is Out Of Range | ||
| NTF mngmtAgentTrap14005 | 1.3.6.1.4.1.232.0.136014005 | View Object - Invalid Object Condition | ||
| NTF mngmtAgentTrap14006 | 1.3.6.1.4.1.232.0.136014006 | View Object - Invalid Object Type | ||
| NTF mngmtAgentTrap14007 | 1.3.6.1.4.1.232.0.136014007 | View List Pointer is NULL | ||
| NTF mngmtAgentTrap14008 | 1.3.6.1.4.1.232.0.136014008 | View Object Pointer is NULL | ||
| NTF mngmtAgentTrap14009 | 1.3.6.1.4.1.232.0.136014009 | Building View List Object - Complete | ||
| NTF mngmtAgentTrap14010 | 1.3.6.1.4.1.232.0.136014010 | Building View List Object - Failed | ||
| NTF mngmtAgentTrap14012 | 1.3.6.1.4.1.232.0.136014012 | View Find by UID Failed | ||
| NTF mngmtAgentTrap14013 | 1.3.6.1.4.1.232.0.136014013 | View Find by Type Failed | ||
| NTF mngmtAgentTrap14017 | 1.3.6.1.4.1.232.0.136014017 | View Find by Type by Name Failed | ||
| NTF mngmtAgentTrap15001 | 1.3.6.1.4.1.232.0.136015001 | Tree View Symbol Not Found | ||
| NTF mngmtAgentTrap15002 | 1.3.6.1.4.1.232.0.136015002 | Tree View Id Symbol Not Found | ||
| NTF mngmtAgentTrap15003 | 1.3.6.1.4.1.232.0.136015003 | Tree Cursor Symbol Not Found | ||
| NTF mngmtAgentTrap15004 | 1.3.6.1.4.1.232.0.136015004 | Tree Cursor Id Symbol Not Found | ||
| NTF mngmtAgentTrap15005 | 1.3.6.1.4.1.232.0.136015005 | Tree Sibling Symbol Not Found | ||
| NTF mngmtAgentTrap15006 | 1.3.6.1.4.1.232.0.136015006 | Tree Total Children Symbol Not Found | ||
| NTF mngmtAgentTrap15007 | 1.3.6.1.4.1.232.0.136015007 | Tree Expansion Symbol Not Found | ||
| NTF mngmtAgentTrap15008 | 1.3.6.1.4.1.232.0.136015008 | Tree Contraction Symbol Not Found | ||
| NTF mngmtAgentTrap15009 | 1.3.6.1.4.1.232.0.136015009 | Tree Invalid Descriptor String | ||
| NTF mngmtAgentTrap16001 | 1.3.6.1.4.1.232.0.136016001 | Ema Short Status - Reissue Command | ||
| NTF mngmtAgentTrap16004 | 1.3.6.1.4.1.232.0.136016004 | Ema Invalid Handle Set In Request Packet | ||
| NTF mngmtAgentTrap16005 | 1.3.6.1.4.1.232.0.136016005 | Ema No Pstore At Referenced Location | ||
| NTF mngmtAgentTrap16008 | 1.3.6.1.4.1.232.0.136016008 | Ema No Device Found | ||
| NTF mngmtAgentTrap16010 | 1.3.6.1.4.1.232.0.136016010 | Ema Could Not Find SubEnclosure in Configuration List | ||
| NTF mngmtAgentTrap16012 | 1.3.6.1.4.1.232.0.136016012 | Ema Non-specific error occurred | ||
| NTF mngmtAgentTrap16013 | 1.3.6.1.4.1.232.0.136016013 | Ema Shelf WWN Could Not Be Accessed Through A Drive | ||
| NTF mngmtAgentTrap16014 | 1.3.6.1.4.1.232.0.136016014 | Ema EMU Failed To Enter Primary Mode | ||
| NTF mngmtAgentTrap16015 | 1.3.6.1.4.1.232.0.136016015 | Ema EMU Failed To Exit Primary Mode | ||
| NTF mngmtAgentTrap16016 | 1.3.6.1.4.1.232.0.136016016 | Ema Downloaded File Does Not Contain Valid Fibre Channel Loader [status:1] | ||
| NTF mngmtAgentTrap16017 | 1.3.6.1.4.1.232.0.136016017 | Ema Downloaded File Format Is Not Recognized [status:2] | ||
| NTF mngmtAgentTrap16018 | 1.3.6.1.4.1.232.0.136016018 | Ema Incorrect Firmware In Downloaded File [status:3] | ||
| NTF mngmtAgentTrap16019 | 1.3.6.1.4.1.232.0.136016019 | Ema Downloaded Loader is Too Large [status:4] | ||
| NTF mngmtAgentTrap16020 | 1.3.6.1.4.1.232.0.136016020 | Ema Invalid Checksum [status:5] | ||
| NTF mngmtAgentTrap16021 | 1.3.6.1.4.1.232.0.136016021 | Ema Previous Offset Plus Previous Length Not Equal To Current Offset [status:6] | ||
| NTF mngmtAgentTrap16022 | 1.3.6.1.4.1.232.0.136016022 | Ema Downloaded Loader Terminated Incorrectly [status:7] | ||
| NTF mngmtAgentTrap16023 | 1.3.6.1.4.1.232.0.136016023 | Ema EMU Out Of Memory [status:8] | ||
| NTF mngmtAgentTrap16024 | 1.3.6.1.4.1.232.0.136016024 | Ema EMU CDB Timeout -- Download Aborted [status:9] | ||
| NTF mngmtAgentTrap16025 | 1.3.6.1.4.1.232.0.136016025 | Ema EMU Internal State Machine Error [status:10] | ||
| NTF mngmtAgentTrap16026 | 1.3.6.1.4.1.232.0.136016026 | Ema EMU Flash Erasure Failure [status:11] | ||
| NTF mngmtAgentTrap16027 | 1.3.6.1.4.1.232.0.136016027 | Ema EMU In Primary Mode - Cannot Download To Primary EMU [status:12] | ||
| NTF mngmtAgentTrap16028 | 1.3.6.1.4.1.232.0.136016028 | Ema Previous Offset Plus Previous Length Greater Than Total Size [status:13] | ||
| NTF mngmtAgentTrap16029 | 1.3.6.1.4.1.232.0.136016029 | Ema Current Total Size Different From Previous Total Size [status:14] | ||
| NTF mngmtAgentTrap16030 | 1.3.6.1.4.1.232.0.136016030 | Ema Could Not Restore Reporting Group Number. Final Download Record Error | ||
| NTF mngmtAgentTrap16031 | 1.3.6.1.4.1.232.0.136016031 | Ema Could Not Recovery From Invop. Invop Retries Exhausted | ||
| NTF mngmtAgentTrap16032 | 1.3.6.1.4.1.232.0.136016032 | Ema Requested WWN Does Not Match Enclosure WWN | ||
| NTF mngmtAgentTrap16033 | 1.3.6.1.4.1.232.0.136016033 | Ema EMU Enclosure Services Error Occurred. EMU May Be Unavailable or Not Installed | ||
| NTF mngmtAgentTrap16034 | 1.3.6.1.4.1.232.0.136016034 | Ema SCSI Error Occurred While Trying To Communicate With EMU | ||
| NTF mngmtAgentTrap16035 | 1.3.6.1.4.1.232.0.136016035 | Ema Could Not Open EMU Firmware File | ||
| NTF mngmtAgentTrap16036 | 1.3.6.1.4.1.232.0.136016036 | Ema EMU Firmware File Name Is Null | ||
| NTF mngmtAgentTrap16037 | 1.3.6.1.4.1.232.0.136016037 | Ema EMU Firmware Download Retries Exhausted. Manual Download May Be Required | ||
| NTF mngmtAgentTrap16038 | 1.3.6.1.4.1.232.0.136016038 | Ema EMU Current Firmware Version Matches Upgrade Firmware Version. No Upgrade Will Be Performed. | ||
| NTF mngmtAgentTrap16039 | 1.3.6.1.4.1.232.0.136016039 | Ema EMU Firmware Upgrade Success | ||
| NTF mngmtAgentTrap16040 | 1.3.6.1.4.1.232.0.136016040 | Ema EMU In Load State. Do Not Power Off. Reload EMU Firmware | ||
| NTF mngmtAgentTrap17001 | 1.3.6.1.4.1.232.0.136017001 | Drive Code Load Descriptor File Open Error | ||
| NTF mngmtAgentTrap17002 | 1.3.6.1.4.1.232.0.136017002 | Drive Code Load Descriptor File Parsing Error - Invalid Line | ||
| NTF mngmtAgentTrap17003 | 1.3.6.1.4.1.232.0.136017003 | Drive Code Load Image File Open Error, | ||
| NTF mngmtAgentTrap17004 | 1.3.6.1.4.1.232.0.136017004 | Drive Code Load Image File Error Getting File Size | ||
| NTF mngmtAgentTrap17005 | 1.3.6.1.4.1.232.0.136017005 | Drive Code Load Image File Buffer Allocation Error | ||
| NTF mngmtAgentTrap17006 | 1.3.6.1.4.1.232.0.136017006 | Drive Code Load Image File Read Error | ||
| NTF mngmtAgentTrap17007 | 1.3.6.1.4.1.232.0.136017007 | Drive Code Load Drive Firmware Update Failed | ||
| NTF mngmtAgentTrap17008 | 1.3.6.1.4.1.232.0.136017008 | Drive Code Load Drive Inquiry Failed | ||
| NTF mngmtAgentTrap17009 | 1.3.6.1.4.1.232.0.136017009 | Drive Code Load Format Command Failed | ||
| NTF mngmtAgentTrap17012 | 1.3.6.1.4.1.232.0.136017012 | Drive Code Load Get Physical Store Condition Failed | ||
| NTF mngmtAgentTrap17013 | 1.3.6.1.4.1.232.0.136017013 | Drive Code Load Get Volume Condition Failed | ||
| NTF mngmtAgentTrap17014 | 1.3.6.1.4.1.232.0.136017014 | Drive Code Load Drive Spin Up Error | ||
| NTF mngmtAgentTrap17015 | 1.3.6.1.4.1.232.0.136017015 | Drive Code Load - Complete | ||
| NTF mngmtAgentTrap17016 | 1.3.6.1.4.1.232.0.136017016 | Drive Code Load Disk Group Migration In Progress | ||
| NTF mngmtAgentTrap17017 | 1.3.6.1.4.1.232.0.136017017 | Drive Code Load Unable To Code Load Disks Part Of A Group | ||
| NTF mngmtAgentTrap18001 | 1.3.6.1.4.1.232.0.136018001 | Api Created Element Success | ||
| NTF mngmtAgentTrap18002 | 1.3.6.1.4.1.232.0.136018002 | Api Created Storage Success | ||
| NTF mngmtAgentTrap18003 | 1.3.6.1.4.1.232.0.136018003 | Api Created Storage Client Success | ||
| NTF mngmtAgentTrap18004 | 1.3.6.1.4.1.232.0.136018004 | Api Set Storage Success | ||
| NTF mngmtAgentTrap18005 | 1.3.6.1.4.1.232.0.136018005 | Api Set Element Success | ||
| NTF mngmtAgentTrap18006 | 1.3.6.1.4.1.232.0.136018006 | Api Deleted Element Success | ||
| NTF mngmtAgentTrap18007 | 1.3.6.1.4.1.232.0.136018007 | Api Deleted Storage Success | ||
| NTF mngmtAgentTrap18008 | 1.3.6.1.4.1.232.0.136018008 | Api Deleted Storage Client Success | ||
| NTF mngmtAgentTrap18009 | 1.3.6.1.4.1.232.0.136018009 | Api Created Snapshot Success | ||
| NTF mngmtAgentTrap18010 | 1.3.6.1.4.1.232.0.136018010 | Api Created Clone Success | ||
| NTF mngmtAgentTrap18018 | 1.3.6.1.4.1.232.0.136018018 | Api Unable To Get The Lock | ||
| NTF mngmtAgentTrap18019 | 1.3.6.1.4.1.232.0.136018019 | Api Created PresentedUnit Success | ||
| NTF mngmtAgentTrap18022 | 1.3.6.1.4.1.232.0.136018022 | Api Create DiskGroup Success | ||
| NTF mngmtAgentTrap18024 | 1.3.6.1.4.1.232.0.136018024 | Api Create Folder Success | ||
| NTF mngmtAgentTrap18025 | 1.3.6.1.4.1.232.0.136018025 | Api Delete Folder Success | ||
| NTF mngmtAgentTrap18028 | 1.3.6.1.4.1.232.0.136018028 | Api Set Folder Success | ||
| NTF mngmtAgentTrap18034 | 1.3.6.1.4.1.232.0.136018034 | Api Invalid User Name Or Password Error | ||
| NTF mngmtAgentTrap18036 | 1.3.6.1.4.1.232.0.136018036 | Api Delete Presented Unit Success | ||
| NTF mngmtAgentTrap18038 | 1.3.6.1.4.1.232.0.136018038 | Api Set Diskgroup Success | ||
| NTF mngmtAgentTrap18039 | 1.3.6.1.4.1.232.0.136018039 | Api Set Disk Success | ||
| NTF mngmtAgentTrap18040 | 1.3.6.1.4.1.232.0.136018040 | Api Delete Storage Family Success | ||
| NTF mngmtAgentTrap18041 | 1.3.6.1.4.1.232.0.136018041 | Api Set Storage Family Success | ||
| NTF mngmtAgentTrap18042 | 1.3.6.1.4.1.232.0.136018042 | Api Control Memory Allocation Failure | ||
| NTF mngmtAgentTrap18045 | 1.3.6.1.4.1.232.0.136018045 | Api Element Codeload Success | ||
| NTF mngmtAgentTrap18047 | 1.3.6.1.4.1.232.0.136018047 | Api Disk Codeload Success | ||
| NTF mngmtAgentTrap18048 | 1.3.6.1.4.1.232.0.136018048 | Api Monitor Codeload Success | ||
| NTF mngmtAgentTrap18049 | 1.3.6.1.4.1.232.0.136018049 | Api Added Port WWID Success | ||
| NTF mngmtAgentTrap18050 | 1.3.6.1.4.1.232.0.136018050 | Api Set Storage Client Success | ||
| NTF mngmtAgentTrap18051 | 1.3.6.1.4.1.232.0.136018051 | Api Invalid Operation | ||
| NTF mngmtAgentTrap18052 | 1.3.6.1.4.1.232.0.136018052 | Api Deleted Port WWID Success | ||
| NTF mngmtAgentTrap18059 | 1.3.6.1.4.1.232.0.136018059 | Api Set Power Success | ||
| NTF mngmtAgentTrap18060 | 1.3.6.1.4.1.232.0.136018060 | Api Element Is Not Initialized | ||
| NTF mngmtAgentTrap18063 | 1.3.6.1.4.1.232.0.136018063 | Api Error trying to delete a disk group | ||
| NTF mngmtAgentTrap18065 | 1.3.6.1.4.1.232.0.136018065 | Api A storage (Vdisk) operation is in progress. Try again later. | ||
| NTF mngmtAgentTrap18066 | 1.3.6.1.4.1.232.0.136018066 | Api The storage (Vdisk) condition is invalid. The storage may be in error. Try again later. | ||
| NTF mngmtAgentTrap18067 | 1.3.6.1.4.1.232.0.136018067 | Api Error calling get Vdisk condition. Vdisk may be deleted. Try again later. | ||
| NTF mngmtAgentTrap18068 | 1.3.6.1.4.1.232.0.136018068 | Api Invalid initialization of the API. Cannot start monitoring process. Storage system management limited. | ||
| NTF mngmtAgentTrap18070 | 1.3.6.1.4.1.232.0.136018070 | Api A command is currently under execution from another API call. Try again later. | ||
| NTF mngmtAgentTrap18071 | 1.3.6.1.4.1.232.0.136018071 | Api The server has not completed initialization, cannot process the request. | ||
| NTF mngmtAgentTrap18073 | 1.3.6.1.4.1.232.0.136018073 | Api Removal of disk from disk group successful | ||
| NTF mngmtAgentTrap18074 | 1.3.6.1.4.1.232.0.136018074 | Api Disk(s) added to disk group successfully | ||
| NTF mngmtAgentTrap18075 | 1.3.6.1.4.1.232.0.136018075 | Api Modify monitor properties successful | ||
| NTF mngmtAgentTrap18076 | 1.3.6.1.4.1.232.0.136018076 | Api Element name too long. Maximum is 20 characters. | ||
| NTF mngmtAgentTrap18080 | 1.3.6.1.4.1.232.0.136018080 | Api The snapshot/Snapclone license cannot be validated. Either the license key has not been entered, or there is a system communication failure. | ||
| NTF mngmtAgentTrap18081 | 1.3.6.1.4.1.232.0.136018081 | Api The folder operation is not valid for the specified folder. Either the folder is a root folder and cannot be modified, or it is a disk group folder for which you should use 'Set Group' command. | ||
| NTF mngmtAgentTrap20001 | 1.3.6.1.4.1.232.0.136020001 | LicMngr Memory Allocation Failure | ||
| NTF mngmtAgentTrap20002 | 1.3.6.1.4.1.232.0.136020002 | LicMngr Startup Complete | ||
| NTF mngmtAgentTrap20003 | 1.3.6.1.4.1.232.0.136020003 | LicMngr Startup Failed | ||
| NTF mngmtAgentTrap20004 | 1.3.6.1.4.1.232.0.136020004 | License successfully checked out | ||
| NTF mngmtAgentTrap20005 | 1.3.6.1.4.1.232.0.136020005 | License checkout failed | ||
| NTF mngmtAgentTrap20011 | 1.3.6.1.4.1.232.0.136020011 | License Line has an incorrect format | ||
| NTF mngmtAgentTrap20013 | 1.3.6.1.4.1.232.0.136020013 | License Library runtime error | ||
| NTF mngmtAgentTrap20015 | 1.3.6.1.4.1.232.0.136020015 | Failed to retrieve Node WWN from storage system | ||
| NTF mngmtAgentTrap20016 | 1.3.6.1.4.1.232.0.136020016 | Failed to retrieve license list from MLD | ||
| NTF mngmtAgentTrap20017 | 1.3.6.1.4.1.232.0.136020017 | Failed to write license list to MLD | ||
| NTF mngmtAgentTrap20018 | 1.3.6.1.4.1.232.0.136020018 | This license line appears to be invalid | ||
| NTF mngmtAgentTrap20019 | 1.3.6.1.4.1.232.0.136020019 | MLD Manager Handle is NULL - unable to update MLD License List | ||
| NTF mngmtAgentTrap20020 | 1.3.6.1.4.1.232.0.136020020 | LicMngr: Storage system handle is NULL | ||
| NTF mngmtAgentTrap20021 | 1.3.6.1.4.1.232.0.136020021 | The license you entered is a valid license but not for the Node WWN and/or firmware version on this controller pair | ||
| NTF mngmtAgentTrap20022 | 1.3.6.1.4.1.232.0.136020022 | Function name string is null or in an incorrect format | ||
| NTF mngmtAgentTrap20023 | 1.3.6.1.4.1.232.0.136020023 | Version string is null or in an incorrect format | ||
| NTF mngmtAgentTrap21001 | 1.3.6.1.4.1.232.0.136021001 | HSV Upgrade Manager Image File Open Error | ||
| NTF mngmtAgentTrap21002 | 1.3.6.1.4.1.232.0.136021002 | HSV Upgrade Manager Image File Buffer Allocation Error | ||
| NTF mngmtAgentTrap21003 | 1.3.6.1.4.1.232.0.136021003 | HSV Upgrade Manager Image File Read Error | ||
| NTF mngmtAgentTrap21004 | 1.3.6.1.4.1.232.0.136021004 | HSV Upgrade Manager Event File Write Error | ||
| NTF mngmtAgentTrap21006 | 1.3.6.1.4.1.232.0.136021006 | HSV Upgrade Manager Global Header Edc Compute Error | ||
| NTF mngmtAgentTrap21007 | 1.3.6.1.4.1.232.0.136021007 | HSV Upgrade Manager Image Header Edc Compute Error | ||
| NTF mngmtAgentTrap21008 | 1.3.6.1.4.1.232.0.136021008 | HSV Upgrade Manager Image Type Exceeds Max Image Count | ||
| NTF mngmtAgentTrap21009 | 1.3.6.1.4.1.232.0.136021009 | HSV Upgrade Manager Image Type Not Controller Image | ||
| NTF mngmtAgentTrap21010 | 1.3.6.1.4.1.232.0.136021010 | HSV Upgrade Manager Image Size Exceeded | ||
| NTF mngmtAgentTrap21011 | 1.3.6.1.4.1.232.0.136021011 | HSV Upgrade Manager Event File Open Error | ||
| NTF mngmtAgentTrap21012 | 1.3.6.1.4.1.232.0.136021012 | HSV Upgrade Manager Image Edc Compute Error | ||
| NTF mngmtAgentTrap21013 | 1.3.6.1.4.1.232.0.136021013 | HSV Upgrade Manager Begin Text Not Found | ||
| NTF mngmtAgentTrap21014 | 1.3.6.1.4.1.232.0.136021014 | HSV Upgrade Manager After Text Not Found | ||
| NTF mngmtAgentTrap21015 | 1.3.6.1.4.1.232.0.136021015 | HSV Upgrade Manager File Format Version Mismatch | ||
| NTF mngmtAgentTrap21016 | 1.3.6.1.4.1.232.0.136021016 | HSV Upgrade Manager Global Header Format Version Mismatch | ||
| NTF mngmtAgentTrap21017 | 1.3.6.1.4.1.232.0.136021017 | HSV Upgrade Manager Product Information Was Not Found | ||
| NTF mngmtAgentTrap21018 | 1.3.6.1.4.1.232.0.136021018 | HSV Upgrade Manager Event File Was Not Found | ||
| NTF mngmtAgentTrap21019 | 1.3.6.1.4.1.232.0.136021019 | HSV Upgrade Manager All Images Match Versions Already Loaded | ||
| NTF mngmtAgentTrap22001 | 1.3.6.1.4.1.232.0.136022001 | Trace: Unable to write management agent trace file | ||
| NTF mngmtAgentTrap22002 | 1.3.6.1.4.1.232.0.136022002 | Trace: file write succeeded | ||
| NTF mngmtAgentTrap23002 | 1.3.6.1.4.1.232.0.136023002 | Diagnostic The view list has errors | ||
| NTF mngmtAgentTrap23003 | 1.3.6.1.4.1.232.0.136023003 | Diagnostic Memory allocation failure | ||
| NTF mngmtAgentTrap24001 | 1.3.6.1.4.1.232.0.136024001 | Windows system error | ||
| NTF mngmtAgentTrap24002 | 1.3.6.1.4.1.232.0.136024002 | Lock is already taken | ||
| NTF mngmtAgentTrap24003 | 1.3.6.1.4.1.232.0.136024003 | Lock is not taken | ||
| NTF mngmtAgentTrap24004 | 1.3.6.1.4.1.232.0.136024004 | Request timed out | ||
| NTF mngmtAgentTrap25001 | 1.3.6.1.4.1.232.0.136025001 | No path to controller | ||
| NTF mngmtAgentTrap25002 | 1.3.6.1.4.1.232.0.136025002 | Thread is not running | ||
| NTF mngmtAgentTrap25003 | 1.3.6.1.4.1.232.0.136025003 | No physical stores | ||
| NTF mngmtAgentTrap25004 | 1.3.6.1.4.1.232.0.136025004 | Loop context ID changed | ||
| NTF mngmtAgentTrap25005 | 1.3.6.1.4.1.232.0.136025005 | Storage Cell context ID changed | ||
| NTF mngmtAgentTrap25006 | 1.3.6.1.4.1.232.0.136025006 | Cache Write Failure | ||
| NTF mngmtAgentTrap25007 | 1.3.6.1.4.1.232.0.136025007 | Battery Disable Failure | ||
| NTF mngmtAgentTrap25008 | 1.3.6.1.4.1.232.0.136025008 | Drive Shelf Disable Failure | ||
| NTF mngmtAgentTrap25009 | 1.3.6.1.4.1.232.0.136025009 | Shutdown Both Restart And Power Off Requested | ||
| NTF mngmtAgentTrap25010 | 1.3.6.1.4.1.232.0.136025010 | Shutdown Drive Shelf Power Off But No Enclosure Power Off Requested | ||
| NTF mngmtAgentTrap25011 | 1.3.6.1.4.1.232.0.136025011 | Shutdown Disable Battery But No Enclosure Power Off Requested | ||
| NTF mngmtAgentTrap25012 | 1.3.6.1.4.1.232.0.136025012 | Shutdown Disable Battery But Shutdown Unconditional Requested | ||
| NTF mngmtAgentTrap25013 | 1.3.6.1.4.1.232.0.136025013 | Shutdown Delay Out Of Range | ||
| NTF mngmtAgentTrap25014 | 1.3.6.1.4.1.232.0.136025014 | Invalid Storage Cell name | ||
| NTF mngmtAgentTrap25015 | 1.3.6.1.4.1.232.0.136025015 | Requested spares goal cannot be satisfied | ||
| NTF mngmtAgentTrap25016 | 1.3.6.1.4.1.232.0.136025016 | No valid LDAD found | ||
| NTF mngmtAgentTrap25017 | 1.3.6.1.4.1.232.0.136025017 | Mismatched MLD size | ||
| NTF mngmtAgentTrap25018 | 1.3.6.1.4.1.232.0.136025018 | Codeload image file error | ||
| NTF mngmtAgentTrap25019 | 1.3.6.1.4.1.232.0.136025019 | Storage System is not initialized | ||
| NTF mngmtAgentTrap26002 | 1.3.6.1.4.1.232.0.136026002 | Invalid data replication operation | ||
| NTF mngmtAgentTrap26005 | 1.3.6.1.4.1.232.0.136026005 | DR group name exceeds maximum length | ||
| NTF mngmtAgentTrap26006 | 1.3.6.1.4.1.232.0.136026006 | DR group created successfully | ||
| NTF mngmtAgentTrap26007 | 1.3.6.1.4.1.232.0.136026007 | Data replication invalid mode for DR Group create | ||
| NTF mngmtAgentTrap26008 | 1.3.6.1.4.1.232.0.136026008 | A duplicate DR group name exists in the specified source or destination DR group. | ||
| NTF mngmtAgentTrap26009 | 1.3.6.1.4.1.232.0.136026009 | Data replication invalid operation while DR Groups exist | ||
| NTF mngmtAgentTrap26010 | 1.3.6.1.4.1.232.0.136026010 | Data replication root folder does not exist | ||
| NTF mngmtAgentTrap26011 | 1.3.6.1.4.1.232.0.136026011 | DR group discarded | ||
| NTF mngmtAgentTrap26012 | 1.3.6.1.4.1.232.0.136026012 | Data replication unknown remote storage system | ||
| NTF mngmtAgentTrap26013 | 1.3.6.1.4.1.232.0.136026013 | Data replication Error. A conflicting Vdisk name exists on the remote storage system. | ||
| NTF mngmtAgentTrap26014 | 1.3.6.1.4.1.232.0.136026014 | Data Replication Error. Invalid Remote Vdisk Name specified. | ||
| NTF mngmtAgentTrap26015 | 1.3.6.1.4.1.232.0.136026015 | Data Replication Error. Remote Vdisk size cannot be modified. | ||
| NTF mngmtAgentTrap26016 | 1.3.6.1.4.1.232.0.136026016 | Data Replication Error. Remote Vdisk should be unpresented to proceed with the discard/detach operation. | ||
| NTF mngmtAgentTrap27001 | 1.3.6.1.4.1.232.0.136027001 | The element manager has successfully initialized storage system. Command issued through XML Interface. | ||
| NTF mngmtAgentTrap27002 | 1.3.6.1.4.1.232.0.136027002 | The element manager has successfully created a virtual disk. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27003 | 1.3.6.1.4.1.232.0.136027003 | The element manager has successfully created a disk group. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27004 | 1.3.6.1.4.1.232.0.136027004 | The element manager has successfully created a DRM group. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27005 | 1.3.6.1.4.1.232.0.136027005 | The element manager has successfully created a host. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27006 | 1.3.6.1.4.1.232.0.136027006 | The element manager has successfully created a presented unit. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27007 | 1.3.6.1.4.1.232.0.136027007 | The element manager has successfully created a virtual disk folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27008 | 1.3.6.1.4.1.232.0.136027008 | The element manager has successfully created a host folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27009 | 1.3.6.1.4.1.232.0.136027009 | The element manager has successfully created a disk group folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27010 | 1.3.6.1.4.1.232.0.136027010 | The element manager has successfully created a DRM group folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27011 | 1.3.6.1.4.1.232.0.136027011 | The element manager has successfully created a folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27012 | 1.3.6.1.4.1.232.0.136027012 | The element manager has successfully created a snapshot. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27013 | 1.3.6.1.4.1.232.0.136027013 | The element manager has successfully created a snapclone. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27014 | 1.3.6.1.4.1.232.0.136027014 | The element manager has successfully uninitialized the storage system. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27015 | 1.3.6.1.4.1.232.0.136027015 | The element manager has successfully deleted a virtual disk. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27016 | 1.3.6.1.4.1.232.0.136027016 | The element manager has successfully deleted a disk group. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27017 | 1.3.6.1.4.1.232.0.136027017 | The element manager has successfully deleted a DRM group. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27018 | 1.3.6.1.4.1.232.0.136027018 | The element manager has successfully deleted a host. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27019 | 1.3.6.1.4.1.232.0.136027019 | The element manager has successfully deleted a presented unit. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27020 | 1.3.6.1.4.1.232.0.136027020 | The element manager has successfully deleted a virtual disk folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27021 | 1.3.6.1.4.1.232.0.136027021 | The element manager has successfully deleted a host folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27022 | 1.3.6.1.4.1.232.0.136027022 | The element manager has successfully deleted a disk group folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27023 | 1.3.6.1.4.1.232.0.136027023 | The element manager has successfully deleted a DRM group folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27024 | 1.3.6.1.4.1.232.0.136027024 | The element manager has successfully deleted a folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27025 | 1.3.6.1.4.1.232.0.136027025 | The element manager has successfully deleted a snapshot. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27026 | 1.3.6.1.4.1.232.0.136027026 | The element manager has successfully modified the properties of a storage system. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27027 | 1.3.6.1.4.1.232.0.136027027 | The element manager has successfully modified the properties of a virtual disk. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27028 | 1.3.6.1.4.1.232.0.136027028 | The element manager has successfully modified the properties of a disk group. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27029 | 1.3.6.1.4.1.232.0.136027029 | The element manager has successfully modified the properties of a DRM group. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27030 | 1.3.6.1.4.1.232.0.136027030 | The element manager has successfully modified the properties of a host. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27031 | 1.3.6.1.4.1.232.0.136027031 | The element manager has successfully modified the properties of a presented unit. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27032 | 1.3.6.1.4.1.232.0.136027032 | The element manager has successfully modified the properties of a virtual disk folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27033 | 1.3.6.1.4.1.232.0.136027033 | The element manager has successfully modified the properties of a host folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27034 | 1.3.6.1.4.1.232.0.136027034 | The element manager has successfully modified the properties of a hardware root folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27035 | 1.3.6.1.4.1.232.0.136027035 | The element manager has successfully modified the properties of a disk group folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27036 | 1.3.6.1.4.1.232.0.136027036 | The element manager has successfully modified the properties of a DRM group folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27037 | 1.3.6.1.4.1.232.0.136027037 | The element manager has successfully modified the properties of a DRM group root folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27038 | 1.3.6.1.4.1.232.0.136027038 | The element manager has successfully modified the properties of a folder. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27039 | 1.3.6.1.4.1.232.0.136027039 | The element manager has successfully modified the properties of a snapshot. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27040 | 1.3.6.1.4.1.232.0.136027040 | The element manager has successfully modified the properties of a disk. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27041 | 1.3.6.1.4.1.232.0.136027041 | The element manager has successfully modified the properties of a disk shelf. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27042 | 1.3.6.1.4.1.232.0.136027042 | The element manager has successfully modified the properties of a controller. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27043 | 1.3.6.1.4.1.232.0.136027043 | The element manager has successfully modified the properties of a controller shelf. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27044 | 1.3.6.1.4.1.232.0.136027044 | The element manager has successfully modified the properties of a cabinet. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27045 | 1.3.6.1.4.1.232.0.136027045 | The element manager has successfully reserved an object. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27046 | 1.3.6.1.4.1.232.0.136027046 | The element manager has successfully released an object. Command issued through the XML Interface. | ||
| NTF mngmtAgentTrap27047 | 1.3.6.1.4.1.232.0.136027047 | XML cache mutex timeout. | ||
| NTF mngmtAgentTrap27048 | 1.3.6.1.4.1.232.0.136027048 | XML cache memory allocation error. | ||
| NTF mngmtAgentTrap27049 | 1.3.6.1.4.1.232.0.136027049 | XML subsystem unknown error. | ||
| cpqElementManager | 1.3.6.1.4.1.232.136 | |||
| cpqHSV | 1.3.6.1.4.1.232.136.1 | |||
| cpqHSVAgent | 1.3.6.1.4.1.232.136.1.1 | |||
| STR agManufacturer | 1.3.6.1.4.1.232.136.1.1.1 | DisplayString | read-only | The name of the StorageWorks HSV Agent manufacturer. |
| INT agMajVersion | 1.3.6.1.4.1.232.136.1.1.2 | INTEGER | read-only | StorageWorks HSV Agent Major Version Number (e.g., 3 for 3.0). |
| INT agMinVersion | 1.3.6.1.4.1.232.136.1.1.3 | INTEGER | read-only | StorageWorks HSV Agent Minor Version Number (e.g., 0 for 3.0). |
| STR agHostName | 1.3.6.1.4.1.232.136.1.1.4 | DisplayString | read-only | The Host System Network Name where the agent resides. |
| OID agEnterprise | 1.3.6.1.4.1.232.136.1.1.5 | OBJECT IDENTIFIER | read-only | The Enterprise ID subtree for StorageWorks HSV Agent MIB is registered. |
| STR agDescription | 1.3.6.1.4.1.232.136.1.1.6 | DisplayString | read-only | The StorageWorks HSV Agent description. |
| agStatusTable | 1.3.6.1.4.1.232.136.1.1.7 | not-accessible | This table holds the status information for each HSV Management Agent. | |
| agentEntry | 1.3.6.1.4.1.232.136.1.1.7.1 | not-accessible | The Agent information entry. | |
| INT agentEntryIndex | 1.3.6.1.4.1.232.136.1.1.7.1.1 | INTEGER | read-only | The index into agentStatusTable . |
| INT agentStatus | 1.3.6.1.4.1.232.136.1.1.7.1.2 | INTEGER | read-only | This variable reports the overall status of the Agent. INFORMATIONAL: Normal Operating Condition MINOR: Warning Condition MAJOR: Failure or Failure Immanent CRITICAL: Agent condition is critical or unknown |
| INT agentEventCode | 1.3.6.1.4.1.232.136.1.1.7.1.3 | INTEGER | read-only | The management agent event code. |
| INT agentEventLevel | 1.3.6.1.4.1.232.136.1.1.7.1.4 | INTEGER | read-only | The management event level. |
| STR agentEventTimeDate | 1.3.6.1.4.1.232.136.1.1.7.1.5 | DisplayString | read-only | The date and time the event occurred dd-mm-yyyy/hr:min:sec. |
| STR agentEventDescription | 1.3.6.1.4.1.232.136.1.1.7.1.6 | DisplayString | read-only | The Description of the management agent event. |
| cpqHSVServer | 1.3.6.1.4.1.232.136.1.2 | |||
| STR srvCPU | 1.3.6.1.4.1.232.136.1.2.1 | DisplayString | read-only | The server CPU type (e.g., 80486). |
| STR srvComputerType | 1.3.6.1.4.1.232.136.1.2.2 | DisplayString | read-only | The server Computer type (e.g., PC/AT). |
| INT srvModel | 1.3.6.1.4.1.232.136.1.2.3 | INTEGER | read-only | The server model number. |
| INT srvSubModel | 1.3.6.1.4.1.232.136.1.2.4 | INTEGER | read-only | The server submodel number. |
| STR srvBiosVersion | 1.3.6.1.4.1.232.136.1.2.5 | DisplayString | read-only | The server BIOS Version. |
| STR srvOS | 1.3.6.1.4.1.232.136.1.2.6 | DisplayString | read-only | The server operating system name (e.g., WINNT). |
| INT srvOSMajVersion | 1.3.6.1.4.1.232.136.1.2.7 | INTEGER | read-only | The server OS major version number (e.g., 3 for WINNT 3.51). |
| INT srvOSMinVersion | 1.3.6.1.4.1.232.136.1.2.8 | INTEGER | read-only | The server OS minor version number (e.g., 51 for WINNT 3.51). |
| hsvObject | 1.3.6.1.4.1.232.136.1.3 | |||
| scell | 1.3.6.1.4.1.232.136.1.3.1 | |||
| INT scellTotal | 1.3.6.1.4.1.232.136.1.3.1.1 | INTEGER | read-only | The total number of StorageCells (storage pools) present in the Fusion System. |
| scellStatusTable | 1.3.6.1.4.1.232.136.1.3.1.2 | not-accessible | This table holds the status information for each StorageCell. | |
| scellEntry | 1.3.6.1.4.1.232.136.1.3.1.2.1 | not-accessible | The StorageCell information entry. | |
| INT scellEntryIndex | 1.3.6.1.4.1.232.136.1.3.1.2.1.1 | INTEGER | read-only | The index into scellStatusTable . |
| STR scellName | 1.3.6.1.4.1.232.136.1.3.1.2.1.2 | DisplayString | read-only | The StorageCell Name. |
| STR scellUUID | 1.3.6.1.4.1.232.136.1.3.1.2.1.3 | DisplayString | read-only | The StorageCell unique ID. |
| INT scellStatus | 1.3.6.1.4.1.232.136.1.3.1.2.1.4 | INTEGER | read-only | This variable reports the overall status of the StorageCell. INFORMATIONAL: Normal Operating Condition MINOR: Warning Condition MAJOR: Failure or Failure Immanent CRITICAL: Condition is critical or unknown |
| STR scellEventDescription | 1.3.6.1.4.1.232.136.1.3.1.2.1.5 | DisplayString | read-only | The StorageCell Event Description. |
| STR scellEventTimeDate | 1.3.6.1.4.1.232.136.1.3.1.2.1.6 | DisplayString | read-only | The StorageCell Event Time and Date. |
| STR scellEventCode | 1.3.6.1.4.1.232.136.1.3.1.2.1.7 | DisplayString | read-only | The StorageCell Event Code. |
| INT scellSWComponent | 1.3.6.1.4.1.232.136.1.3.1.2.1.8 | INTEGER | read-only | The Event Code Software Component ID. |
| INT scellECode | 1.3.6.1.4.1.232.136.1.3.1.2.1.9 | INTEGER | read-only | The StorageCell Event Code event number. |
| INT scellCAC | 1.3.6.1.4.1.232.136.1.3.1.2.1.10 | INTEGER | read-only | The event code Corrective Action Code. |
| INT scellEIP | 1.3.6.1.4.1.232.136.1.3.1.2.1.11 | INTEGER | read-only | The Event Code EIP Type. |
| STR scellNameDateTime | 1.3.6.1.4.1.232.136.1.3.1.2.1.12 | DisplayString | read-only | The StorageCell Name: Date & Time of Event. |
| agent | 1.3.6.1.4.1.232.136.1.3.2 | |||
| host | 1.3.6.1.4.1.232.136.1.3.3 | |||
| INT hostTotal | 1.3.6.1.4.1.232.136.1.3.3.1 | INTEGER | read-only | The total number of hosts attached the Fusion System. |
| hostStatusTable | 1.3.6.1.4.1.232.136.1.3.3.2 | not-accessible | This table holds the status information for each Host. | |
| hostEntry | 1.3.6.1.4.1.232.136.1.3.3.2.1 | not-accessible | The Host information entry. | |
| INT hostEntryIndex | 1.3.6.1.4.1.232.136.1.3.3.2.1.1 | INTEGER | read-only | The index into hostStatusTable . |
| STR hostName | 1.3.6.1.4.1.232.136.1.3.3.2.1.2 | DisplayString | read-only | The Host Name. |
| STR hostUUID | 1.3.6.1.4.1.232.136.1.3.3.2.1.3 | DisplayString | read-only | The Host unique ID. |
| INT hostStatus | 1.3.6.1.4.1.232.136.1.3.3.2.1.4 | INTEGER | read-only | This variable reports the overall status of the Host. INFORMATIONAL: Normal Operating Condition MINOR: Warning Condition MAJOR: Failure or Failure Immanent CRITICAL: Condition is critical or unknown |
| nsc | 1.3.6.1.4.1.232.136.1.3.4 | |||
| INT nscTotal | 1.3.6.1.4.1.232.136.1.3.4.1 | INTEGER | read-only | The total number of Network Storage Controllers present in the Fusion System. |
| nscStatusTable | 1.3.6.1.4.1.232.136.1.3.4.2 | not-accessible | This table holds the status information for each Network Storage Controller. | |
| nscEntry | 1.3.6.1.4.1.232.136.1.3.4.2.1 | not-accessible | The NSC information entry. | |
| INT nscEntryIndex | 1.3.6.1.4.1.232.136.1.3.4.2.1.1 | INTEGER | read-only | The index into nscStatusTable . |
| STR nscName | 1.3.6.1.4.1.232.136.1.3.4.2.1.2 | DisplayString | read-only | The Network Storage Controller Name. |
| STR nscUUID | 1.3.6.1.4.1.232.136.1.3.4.2.1.3 | DisplayString | read-only | The NSC unique ID. |
| INT nscStatus | 1.3.6.1.4.1.232.136.1.3.4.2.1.4 | INTEGER | read-only | This variable reports the overall status of the Network Storage Controller. INFORMATIONAL: Normal Operating Condition MINOR: Warning Condition MAJOR: Failure or Failure Immanent CRITICAL: Condition is critical or unknown |
| shelf | 1.3.6.1.4.1.232.136.1.3.8 | |||
| INT shelfTotal | 1.3.6.1.4.1.232.136.1.3.8.1 | INTEGER | read-only | The total number of disk shelves present in the HSV system. |
| shelfStatusTable | 1.3.6.1.4.1.232.136.1.3.8.2 | not-accessible | This table holds the status information for each Shelf. | |
| shelfEntry | 1.3.6.1.4.1.232.136.1.3.8.2.1 | not-accessible | The Shelf information entry. | |
| INT shelfEntryIndex | 1.3.6.1.4.1.232.136.1.3.8.2.1.1 | INTEGER | read-only | The index into shelfStatusTable . |
| INT shelfStatus | 1.3.6.1.4.1.232.136.1.3.8.2.1.2 | INTEGER | read-only | This variable reports the overall status of the Shelf. OTHER: unknown or undeterminable OK: Normal Operating Condition DEGRADED: Warning Condition FAILED: Failure |
| INT shelfId | 1.3.6.1.4.1.232.136.1.3.8.2.1.3 | INTEGER | read-only | The Shelf Id (shelf number). |
| INT shelfElementType | 1.3.6.1.4.1.232.136.1.3.8.2.1.4 | INTEGER | read-only | The Shelf Element type. 01: Disk 02: Power Supply 03: Fan 04: Temp Sensor 06: Alarm Horn 07: EMU 12: LCD 15: GBIC 16: Language 17: Comm Port 18: Volt Sensor 19: Amp Sensor 128:Enclosure 130:Back plane 255:Host |
| INT shelfElementNum | 1.3.6.1.4.1.232.136.1.3.8.2.1.5 | INTEGER | read-only | Which particular Element of that type. |
| INT shelfErrorCode | 1.3.6.1.4.1.232.136.1.3.8.2.1.6 | INTEGER | read-only | The Element Type's Error Code. |
| maHSVMibRev | 1.3.6.1.4.1.232.136.1.4 | |||
| INT maHSVMibRevMajor | 1.3.6.1.4.1.232.136.1.4.1 | INTEGER | read-only | The Major Revision level. A change in the major revision level represents a major change in the architecture of the MIB. A change in the major revision level may indicate a significant change in the information supported and/or the meaning of the supported information, correct interpretation of data may require a MIB document with the same major revision level. |
| INT maHSVMibRevMinor | 1.3.6.1.4.1.232.136.1.4.2 | INTEGER | read-only | The Minor Revision level. A change in the minor revision level may represent some minor additional support, no changes to any pre-existing information has occurred. |
RFC description
HP StorageWorks HSV (Hierarchical Storage Virtualization) array management MIB for agent version and device information.
Start monitoring HP StorageWorks HSV110 (EVA) array controller with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.