HPN-ICF-EPON-UNI-MIB

All MIBs › HPN-ICF-EPON-UNI-MIB

Last Updated: 2008-07-28

Category: Technology: EPON/PON, Vendor: H3C/HH3C, Vendor: HP/HPE

Description: Manages user-network interface (UNI) port configuration and statistics on HP/Comware EPON access devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-EPON-UNI-MIB?

HPN-ICF-EPON-UNI-MIB manages the User-Network Interface (UNI) ports on HP Networking EPON (Ethernet Passive Optical Network) Optical Network Units (ONUs), the subscriber-facing Ethernet ports on fiber access equipment. It exposes per-port configuration and status through hpnicfEponUniSysManTable, including administrative status, port description, MDI/MDI-X setting, priority, and VLAN configuration such as access VLAN, trunk PVID, and trunk allow-list VLAN range. Its monitoring value is in confirming the operational and configuration status of subscriber-facing ports on fiber access hardware — whether a UNI port is administratively up, correctly VLAN-tagged for the subscriber's service, and configured with the right priority — useful for diagnosing a subscriber connectivity or VLAN misconfiguration issue. It is closely related to the EPON/EOC common MIB family and depends on the underlying ONU hardware model rather than a general IETF standard. It is deployed by fiber access network operators managing ONU customer-facing ports in FTTH/FTTB PON deployments. Network engineers evaluating or troubleshooting this functionality can download the HPN-ICF-EPON-UNI-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-EPON-UNI-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP Networking EPON ONU (Optical Network Unit)

Monitoring Examples

An operator troubleshooting a subscriber with no connectivity can check hpnicfEponUniAdminStatus and hpnicfEponUniAccessVlan/hpnicfEponUniTrunkPvid on the relevant hpnicfEponUniSysManTable entry to confirm the UNI port is enabled and mapped to the correct VLAN; a port showing the wrong hpnicfEponUniVlanType or an unexpected hpnicfEponUniVLANTrunkAllowListLow/High range would explain traffic being dropped or misrouted for that subscriber.

What Can Be Monitored

UNI port admin status
port VLAN type and access VLAN/trunk PVID
VLAN trunk allow-list range
port priority
MDI/MDI-X setting

Imported Objects

From HPN-ICF-OID-MIB

hpnicfEpon

OBJECT-IDENTITY

From IF-MIB

ifDescr	OBJECT-TYPE
ifIndex	OBJECT-TYPE

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfEponUni	1.3.6.1.4.1.11.2.14.11.15.2.42.5			The objects in this MIB module are used to manage and display current configuration of UNI (user network interface) which is based on the ONU(Optical Network Unit).
hpnicfEponUniSysMan	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1
hpnicfEponUniSysManTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1		not-accessible	This table defines several UNI system parameters.
hpnicfEponUniSysManEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1		not-accessible	The entry of hpnicfEponUniSysManTable.
I32 hpnicfEponUniIndex	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.1	Integer32	accessible-for-notify	The index value which uniquely identifies the FE(fast Ethernet) interface of the ONU.
OCT hpnicfEponUniDescr	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.2	OCTET STRING	read-only	A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware and software.
INT hpnicfEponUniAdminStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.3	INTEGER	read-write	The desired state of the user network interface. When a managed system initializes, all user network interfaces start with down(2) state. The testing(3)state indicates that no operational packets can be passed. As a result of either explicit management action or per configuration information retained by the managed system, hpnicfEponUniAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
INT hpnicfEponUniMdi	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.4	INTEGER	read-write	Type of the line connected to UNI interface: mdi-ii(straight-through cable), mdi-x (crossover cable), mdi-auto (auto-sensing).
I32 hpnicfEponUniPriority	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.5	Integer32	read-write	The priority of user network interface. If the value is larger, the priority will be higher.
INT hpnicfEponUniVlanType	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.6	INTEGER	read-write	UNI vlan types.
I32 hpnicfEponUniAccessVlan	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.7	Integer32	read-write	The vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
INT hpnicfEponUniTrunkPvid	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.8	INTEGER	read-write	PVID(port vlan ID), the vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
OCT hpnicfEponUniVLANTrunkAllowListLow	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.9	OCTET STRING	read-write	Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans. the vlan is not allowed if its bit has a value of '0'.
OCT hpnicfEponUniVLANTrunkAllowListHigh	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.10	OCTET STRING	read-write	Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 2049 through 2056, the second octet specifying vlans 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered vlan, and the least significant bit represents the lowest numbered vlan. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans; the vlan is not allowed if its bit has a value of '0'.
I32 hpnicfEponUniInboundLineRate	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.11	Integer32	read-write	The value of the inbound line-rate. measured with kbps. The upper limit of the line-rate is the value of hpnicfEponUniLineRateMax in the entry. It must be multiple of the value of hpnicfEponUniLineRateStep. The default value of hpnicfEponUniLineRate is the value of hpnicfEponUniLineRateMax.
I32 hpnicfEponUniOutboundLineRate	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.12	Integer32	read-write	The value of the outbound line-rate. measured with kbps. The upper limit of the line-rate is the value of hpnicfEponUniLineRateMax in the entry. It must be multiple of the value of hpnicfEponUniLineRateStep. The default value of hpnicfEponUniLineRate is the value of hpnicfEponUniLineRateMax.
T/F hpnicfEponUniFlowControl	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.13	TruthValue	read-write	Flow control status. true(1) - Flow control status enable. false(2) - Flow control status disable.
INT hpnicfEponUniSpeed	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.14	INTEGER	read-write	User network interface speed.
INT hpnicfEponUniDuplex	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.15	INTEGER	read-write	User network interface mode.
T/F hpnicfEponUniVlanVPNStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.16	TruthValue	read-write	vlan VPN status. true(1) - vlan VPN status enable. false(2) - vlan VPN disable.
INT hpnicfEponUniCountReset	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.17	INTEGER	read-write	Reset the counter which is about packets of the interface, then the counter will change to zero. There is no sense in reading this object.
INT hpnicfEponUniPortIsolate	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.18	INTEGER	read-write	enable - enable UNI port isolate setting. disable - disable UNI port isolate setting.
OCT hpnicfEponUniVlanConfiguration	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.23	OCTET STRING	read-write	The vlan configuration of the related vlan mode. Transparent vlan mode: hpnicfEponUniVlanConfiguration is a zero length string. Tag vlan mode: the first four octets were the tag assigned to untagged frames received on UNI, including TPID, VID,CFI and priority. Translation vlan mode: the first four octets were the old tag (including TPID, VID, CFI and priority), which is replaced by the new tag(including TPID, VID, CFI and priority), the second four octets.
INT hpnicfEponUniAutoNegotiation	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.25	INTEGER	read-write	enable - enable auto negotiation. disable - disable auto negotiation.
INT hpnicfEponUniRestartAutoNeg	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.26	INTEGER	read-write	Force to restart the auto negotiation process.
INT hpnicfEponUniLinkStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.29	INTEGER	read-only	The link status of UNI.
INT hpnicfEponUniInterfaceType	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.30	INTEGER	read-only	UNI interface type.
INT hpnicfEponUniVitualCableTest	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.31	INTEGER	read-write	True(1): Virtual cable test enable. False(2): Virtual cable test disable.
INT hpnicfEponUniVCTCableStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.32	INTEGER	read-only	Get the cable status. Normal(1),cable is normal. Abnormal(2),cable is abnormal. AbnormalOpen(3),cable is abnormal because of open circuit. AbnormalShort(4),cable is abnormal because of short circuit. Failure(5),cable is abnormal because of testing failure.
I32 hpnicfEponUniVCTCableLength	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.33	Integer32	read-only	Get the cable length. When hpnicfEponUniVCTCableStatus is normal, the node stands for the length from the UNI port to the port opposite. When hpnicfEponUniVCTCableStatus is abnormal, it stands for the lengh from the UNI port to the failure place. Unit:meter(m).
INT hpnicfEponUniVCTImpedanceMismatch	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.34	INTEGER	read-only	Get the cable impedance. Not-support(1),the UNI port does not support this function. True(2),impedance match. False(3),impedance mismatch.
I32 hpnicfEponUniVCTPairSkew	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.35	Integer32	read-only	Get the symmetry of cable. If the function is not supported, the default value 0 will be returned. Unit:nanosecond(ns).
INT hpnicfEponUniVCTPairSwap	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.36	INTEGER	read-only	NotSupport(1),the UNI port does not support this function. True(2),pair swap. False(3),not pair swap.
INT hpnicfEponUniVCTPolaritySwap	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.37	INTEGER	read-only	NotSupport(1),the UNI port does not support this function. True(2),polarity swap. False(3),not polarity swap.
I32 hpnicfEponUniVCTInsertionLoss	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.38	Integer32	read-only	If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
I32 hpnicfEponUniVCTReturnLoss	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.39	Integer32	read-only	If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
I32 hpnicfEponUniVCTNearendCrosstalk	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.40	Integer32	read-only	If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
I32 hpnicfEponUniVlan	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.1.1.41	Integer32	accessible-for-notify	If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
hpnicfEponUniCountTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2		not-accessible	A list of interface counter about frames entries.
hpnicfEponUniCountEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1		not-accessible	An entry containing management information applicable to a particular interface.
U32 hpnicfEponUniInStatsPkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.1	Unsigned32	read-only	The total number of frames (including bad frames, broadcast frames, and multicast frames) received.
U32 hpnicfEponUniInStatsUnicastPkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.2	Unsigned32	read-only	The total number of good frames received that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
U32 hpnicfEponUniInStatsBroadcastPkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.3	Unsigned32	read-only	The total number of good frames received that are directed to the broadcast address. Note that this does not include multicast frames.
U32 hpnicfEponUniInStatsMulticastPkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.4	Unsigned32	read-only	The total number of good frames received that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
U32 hpnicfEponUniInPausePkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.5	Unsigned32	read-only	A count of MAC Control frames received on this interface by the pause(flow control) operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
U32 hpnicfEponUniInTotalErrors	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.6	Unsigned32	read-only	Total count of the error frames received on this interface.
U32 hpnicfEponUniInStatsCRCAlignErrors	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.7	Unsigned32	read-only	The total number of frames received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
U32 hpnicfEponUniInStatsUndersizePkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.8	Unsigned32	read-only	The total number of frames received that are less than 64 octets long (excluding framing bits, but including FCS octets) and are otherwise well formed.
U32 hpnicfEponUniInStatsOversizePkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.9	Unsigned32	read-only	The total number of frames received that are longer than 1518 octets (excluding framing bits, but including FCS octets) and are otherwise well formed.
U32 hpnicfEponUniInErrorbyOther	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.10	Unsigned32	read-only	The total number of error frames received on this interface.
U32 hpnicfEponUniOutStatsPkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.11	Unsigned32	read-only	The total number of frames (including bad frames, broadcast frames, and multicast frames) sent.
U32 hpnicfEponUniOutStatsUnicastPkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.12	Unsigned32	read-only	The total number of good frames sent that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
U32 hpnicfEponUniOutStatsBroadcastPkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.13	Unsigned32	read-only	The total number of good frames sent that are directed to the broadcast address. Note that this does not include multicast frames.
U32 hpnicfEponUniOutStatsMulticastPkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.14	Unsigned32	read-only	The total number of good frames sent that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
U32 hpnicfEponUniOutStatsPausePkts	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.15	Unsigned32	read-only	The total number of MAC control frames sent on this interface by the pause operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
U32 hpnicfEponUniOutTotalErrors	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.16	Unsigned32	read-only	The total number of error frames sent on this interface.
U32 hpnicfEponUniOutStatsCollisions	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.17	Unsigned32	read-only	The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment could. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
U32 hpnicfEponUniOutDelayExceededDiscards	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.18	Unsigned32	read-only	The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
U32 hpnicfEponUniOutErrorbyOther	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.19	Unsigned32	read-only	The total number of other error frames sent on this interface. Other error frames means the error frames out of collision frames and excessive delayed frames.
U32 hpnicfEponUniOutDroppedFrames	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.2.1.20	Unsigned32	read-only	The total number of frames dropped because of buffer failure.
hpnicfEponUniIgmpInfoTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3		not-accessible	This table stores igmp information of UNI interface.
hpnicfEponUniIgmpInfoEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3.1		not-accessible	The entry of hpnicfEponUniIgmpInfoTable.
I32 hpnicfEponUniMacIndex	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3.1.1	Integer32	not-accessible	The index uniquely identifies the igmp information in current UNI interface.
MAC hpnicfEponUniIgmpMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3.1.2	MacAddress	read-only	A 6-octet read-only value carrying the individual MAC address indicates which igmp group the UNI interface belonging to.
I32 hpnicfEponUniIgmpVlanId	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.3.1.3	Integer32	read-only	An integer range from 1 to 4094 indicates the vlan which the igmp Mac address has joined in.
hpnicfEponUniParaMan	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.4
I32 hpnicfEponUniLineRateMax	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.4.1	Integer32	read-only	The maximum value of the line-rate(kbps) that user network interface can be set.
I32 hpnicfEponUniLineRateStep	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.4.2	Integer32	read-only	The step of line-rate(kbps).
I32 hpnicfEponUniNumberOnOnu	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.4.3	Integer32	read-only	The user network interface number on ONU.
hpnicfEponUniScalarGroup	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.5
hpnicfEponUniPortPolicyTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6		not-accessible	UNI port policy configuration.
hpnicfEponUniPortPolicyEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1		not-accessible	The entry of hpnicfEponUniPortPolicyTable.
INT hpnicfEponUniPortPolicyStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.1	INTEGER	read-write	enable - enable UNI upstream port policing. disable - disable UNI upstream port policing.
I32 hpnicfEponUniPortPolicyCir	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.2	Integer32	read-write	The committed information rate, ranging from 1 to 102400, measured in kbps.
I32 hpnicfEponUniPortPolicyBucketDepth	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.3	Integer32	read-write	The depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
I32 hpnicfEponUniPortPolicyExtraBurst	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.4	Integer32	read-write	The extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
I32 hpnicfEponUniPortPolicyInboundCir	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.5	Integer32	read-write	The inbound committed information rate, measured in kbps.
I32 hpnicfEponUniPortPolicyInboundBucketDepth	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.6	Integer32	read-write	The inbound depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
I32 hpnicfEponUniPortPolicyInboundExtraBurst	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.7	Integer32	read-write	The inbound extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
I32 hpnicfEponUniPortPolicyOutboundCir	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.8	Integer32	read-write	The outbound committed information rate, stepped by 64, measured in kbps.
I32 hpnicfEponUniPortPolicyOutboundPir	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.6.1.9	Integer32	read-write	The outbound peak information rate, stepped by 64, measured in kbps.
hpnicfEponUniMulticastTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7		not-accessible	UNI multicast configuration.
hpnicfEponUniMulticastEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1		not-accessible	The entry of hpnicfEponUniPortPolicyTable.
I32 hpnicfEponUniMulticastGroupNumber	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1.1	Integer32	read-write	The allowed multicast group number that can be handled at the same time by UNI.
OCT hpnicfEponUniMulticastVlanList	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1.2	OCTET STRING	read-write	The multicast vlan list. The first two octets of the string represent the first VLAN ID; the second two octets of the string represent the second VLAN ID, and so on. It is a zero length string by default.
INT hpnicfEponUniMulticastStripStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1.3	INTEGER	read-write	true - strip the vlan tag of multicast packet. false - does not strip the vlan tag of multicast packet.
T/F hpnicfEponUniMulticastFastleave	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.7.1.4	TruthValue	read-write	true(1) - fast leave of IGMP enable on ONU. false(2) - fast leave of IGMP disable on ONU.
hpnicfEponUniTechAbilityTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.8		not-accessible	UNI multicast configuration.
hpnicfEponUniTechAbilityEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.8.1		not-accessible	The entry of hpnicfEponUniTechAbilityTable.
OCT hpnicfEponUniLocalTechAbility	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.8.1.1	OCTET STRING	read-only	The local port capabilities of the UNI. Each two octets stand for a capability of UNI: the first two octets represent one capability and the second two octets represent another capability, and so on. The capabilities list: 1 - undefined, 2 - initializing, true ability not yet known, 14 - 10BASE-T, 142 - full duplex 10BASE-T, 23 - 100BASE-T4, 25 - 100BASE-TX, 252 - full duplex 100BASE-TX, 312 - PAUSE operation for full duplex links, 313 - asymmetric PAUSE operation for full duplex links, 314 - symmetric PAUSE operation for full duplex links, 32 - 100BASE-T2, 322 - full duplex 100BASE-T2, 36 - 1000BASE-X, 362 - full duplex 1000BASE-X, 40 - 1000BASE-T UTP PHY, 402 - full duplex 1000BASE-T UTP PHY, 37 - remote fault bit 1(RF1), 372 - remote fault bit 2(RF2), 8029 - 802.9ISLAN-16T.
OCT hpnicfEponUniAdvertisedTechAbility	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.8.1.2	OCTET STRING	read-only	The advertised port capabilities of the UNI. The capabilities list references the description of hpnicfEponUniLocalTechAbility.
hpnicfEponUniMulticastControlTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9		not-accessible	UNI multicast control parameters.
hpnicfEponUniMulticastControlEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1		not-accessible	The entry of the table hpnicfEponUniMulticastControlTable.
I32 hpnicfEponUniMulticastVlanIndex	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.1	Integer32	read-create	The multicast vlan ID.
OCT hpnicfEponUniMulticastAddressList	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.2	OCTET STRING	read-create	The multicast address, each four octets represents a multicast address, the address section ranging from the first four octets to the second four octets, and the like.
INT hpnicfEponUniMulticastAccessRule	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.3	INTEGER	read-create	deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
I32 hpnicfEponUniMulticastChannelLimit	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.4	Integer32	read-create	The limitation of multicast preview channel number.
I32 hpnicfEponUniMulticastPreTimeSlice	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.5	Integer32	read-create	The time slice of multicast preview.
I32 hpnicfEponUniMulticastPreTimes	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.6	Integer32	read-create	The number of multicast preview times.
I32 hpnicfEponUniMulticastPreInterval	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.7	Integer32	read-create	The interval between two consecutive previews, measured in minute.
ROW hpnicfEponUniMulticastRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.8	RowStatus	read-create	The status of this table entry. The active, createAndGo and the destory statuses are supported.
INT hpnicfEponUniMulticastIndex	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.9	INTEGER	not-accessible	The index of the entry.
OCT hpnicfEponUniMulticastSourceIpList	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.10	OCTET STRING	read-create	This list contains many source ip addresses. Each ip address is contained in four octets.
I32 hpnicfEponUniMulticastResetInterval	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.9.1.11	Integer32	read-create	The interval is measured in minute. From the last preview limitation is reached, a customer can preview again after this interval is expired.
hpnicfEponUniQosIndexNextTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.10		not-accessible	The next index table.
hpnicfEponUniQosIndexNextEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.10.1		not-accessible	The entry of the table hpnicfEponUniQosIndexNextTable.
I32 hpnicfEponUniQosConfIndexNext	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.10.1.1	Integer32	read-only	This object contains an appropriate value to be used for hpnicfEponUniQosConfIndex when creating rows in the hpnicfEponUniQosConfTable.
hpnicfEponUniQosConfTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11		not-accessible	UNI Qos configuration.
hpnicfEponUniQosConfEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1		not-accessible	The entry of the table hpnicfEponUniQosConfTable.
I32 hpnicfEponUniQosConfIndex	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.1	Integer32	not-accessible	The rule index.
I32 hpnicfEponUniQosConfRuleIndexNext	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.2	Integer32	read-only	This object contains an appropriate value to be used for hpnicfEponUniQosRuleIndex when creating rows in the hpnicfEponUniQosRuleTable.
I32 hpnicfEponUniQosConfMappedQueue	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.3	Integer32	read-create	The queue that the ethernet frames will be mapped.
I32 hpnicfEponUniQosConfMarkedPriority	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.4	Integer32	read-create	Priority of the ethernet frames to be marked, which compliant with the 802.1D user priority standard.
ROW hpnicfEponUniQosConfRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.11.1.5	RowStatus	read-create	The status of this table entry. The active, createAndGo and the destory statuses are supported.
hpnicfEponUniQosRuleTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12		not-accessible	Qos sub rule of the UNI.
hpnicfEponUniQosRuleEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1		not-accessible	The entry of the table hpnicfEponUniQosRuleTable.
I32 hpnicfEponUniQosRuleIndex	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.1	Integer32	not-accessible	The sub rule index.
INT hpnicfEponUniQosRuleSelector	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.2	INTEGER	read-create	The ethernet frame selector. dstmac - based on destination MAC address. srcmac - based on source MAC address. ethernetpriority - based on ethernet priority. vlanid - based on VLAN ID. ethernettype - based on ethernet type. dstip - based on destination IP address. srcip - based on source IP address. ipprototype - based on IP type(ipv4 or ipv6). ipv4tosdscp - based on IP TOS/DSCP. ipv6 - based IP precedence. srcport - based on layer 4 source port. dstport - based on layer 4 destination port.
I32 hpnicfEponUniQosRuleValue	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.3	Integer32	read-create	The rule value based on the hpnicfEponUniQosRuleSelector.
MAC hpnicfEponUniQosRuleMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.4	MacAddress	read-create	MAC Address.
INT hpnicfEponUniQosRuleOperator	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.5	INTEGER	read-create	nervermatch - value never match. equal - field equal to the value. notequal - field not equal to the value. lessthanequal - field less than or equal to the value. greaterthanequal - field greater than or equal to the value. fieldexist - value is ignored if field exists. fieldnotexist - value is ignored if field does not exist. alwaysmatch - value always match.
ROW hpnicfEponUniQosRuleRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.12.1.6	RowStatus	read-create	The status of this table entry. Only active, createAndGo and the destory are supported.
hpnicfEponUniMirrorGroupTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13		not-accessible	Qos sub rule of the UNI.
hpnicfEponUniMirrorGroupEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1		not-accessible	The entry of the hpnicfEponUniMirrorGroupTable.
I32 hpnicfEponUniMirrorGroupID	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.1	Integer32	not-accessible	Epon UNI mirror group ID.
OCT hpnicfEponUniMirrorInboundPortList	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.2	OCTET STRING	read-write	UNI inbound port list. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered UNI, and the least significant bit represents the lowest numbered UNI. Thus, each UNI port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is allowed in the set of ports. the port is not allowed if its bit has a value of '0'.
OCT hpnicfEponUniMirrorOutboundPortList	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.3	OCTET STRING	read-create	UNI outnbound port list, more infomation reference hpnicfEponUniMirrorInboundPortList
I32 hpnicfEponUniMonitorPort	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.4	Integer32	read-create	UNI monitor port.
ROW hpnicfEponUniMirrorRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.13.1.5	RowStatus	read-create	RowStatus, Now support three status: createAndGo, active, destroy.
hpnicfEponUniMirrorGroupIdNextTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.14		not-accessible	The next index table, which is used by hpnicfEponUniMirrorGroupTable.
hpnicfEponUniMirrorGroupIdNextEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.14.1		not-accessible	The entry of the table hpnicfEponUniMirrorGroupIdNextEntry.
I32 hpnicfEponUniMirrorGroupIDNext	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.14.1.1	Integer32	read-only	This object contains an appropriate value to be used for hpnicfEponUniMirrorGroupID when creating rows in the hpnicfEponUniMirrorGroupTable.
hpnicfEponUniMulticastCtrlInfoTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15		not-accessible	UNI multicast information which is active .
hpnicfEponUniMulticastCtrlInfoEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1		not-accessible	The entry of the table hpnicfEponUniMulticastCtrlInfoTable.
I32 hpnicfEponUniMultActVlan	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.1	Integer32	not-accessible	The multicast vlan ID which is active.
IP hpnicfEponUniMultActAddress	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.2	IpAddress	not-accessible	The multicast address which is active.
INT hpnicfEponUniMultActAccessRule	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.3	INTEGER	read-only	deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
I32 hpnicfEponUniMultActPreTimes	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.4	Integer32	read-only	The number of multicast preview times which is active.
I32 hpnicfEponUniMultActPreRemain	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.15.1.5	Integer32	read-only	The remanent time slice of multicast preview which is active.
hpnicfEponUniMulticastIndexNextTable	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.16		not-accessible	The next index table, which is used by hpnicfEponUniMulticastControlTable.
hpnicfEponUniMulticastIndexNextEntry	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.16.1		not-accessible	The entry of the table hpnicfEponUniMulticastIndexNextEntry.
I32 hpnicfEponUniMulticastConfIndexNext	1.3.6.1.4.1.11.2.14.11.15.2.42.5.1.16.1.1	Integer32	read-only	This object contains an appropriate value to be used for hpnicfEponUniMulticastIndex when creating rows in the hpnicfEponUniMulticastControlTable.
hpnicfEponUniTrap	1.3.6.1.4.1.11.2.14.11.15.2.42.5.2
hpnicfEponUniTrapPrefix	1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0
NTF hpnicfEponUniLinkUpTrap	1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0.1			A hpnicfEponUniLinkUpTrap notification is sent when the UNI up event is detected and the transmitting switch is turned on.
NTF hpnicfEponUniLinkDownTrap	1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0.2			A hpnicfEponUniLinkDownTrap notification is sent when the UNI down event is detected and the transmitting switch is turned on.
NTF hpnicfEponUniLoopBackDetectedTrap	1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0.3			A hpnicfEponUniLoopBackDetectedTrap notification is sent when the UNI loopback event is detected.
NTF hpnicfEponUniLoopBackRecoveredTrap	1.3.6.1.4.1.11.2.14.11.15.2.42.5.2.0.4			A hpnicfEponUniLoopBackRecoveredTrap notification is sent when the UNI loopback is recovered.

RFC description

Management Information Base for EPON User Network Interface on HP networking devices. Provides objects for managing EPON ONU interfaces, optical parameters, and UNI port configuration.

Start monitoring HP Networking EPON ONUs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-EPON-UNI-MIB

What Is HPN-ICF-EPON-UNI-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description