HPN-ICF-MPLS-LDP-MIB

All MIBs › HPN-ICF-MPLS-LDP-MIB

Last Updated: 1999-06-30

Category: MPLS and Traffic Engineering, Vendor: H3C/HH3C, Vendor: HP/HPE

Description: Manages Label Distribution Protocol (LDP) sessions, label bindings, and FEC tables on HP/Comware MPLS devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-MPLS-LDP-MIB?

HPN-ICF-MPLS-LDP-MIB is an HP/H3C (Comware "ICF") vendor MIB derived from the IETF MPLS LDP draft MIB, adapted for HP networking devices running MPLS Label Distribution Protocol. It models LDP label switch router (LSR) incarnations via hpnicfMplsLdpLsrIncarnTable (hpnicfMplsLdpLsrID, hpnicfMplsLdpLsrHopCountLimit, hpnicfMplsLdpLsrPathVectorLimit, hpnicfMplsLdpLsrLoopDetectionAdminStatus), plus separate object groups for LDP entities, peers, sessions, hello adjacencies, and CR-LSP tunnels, and defines failure notifications such as hpnicfMplsLdpSessionUpEventFailure/DownEventFailure and hpnicfMplsLdpEntityUpEventFailure/DownEventFailure. It exposes control-plane configuration and session-state data for LDP label distribution rather than raw traffic counters, letting operators confirm that LDP sessions and hello adjacencies with neighboring LSRs are established and stable. It depends on the broader MPLS/LSR and TE MIB framework, since LDP-established label bindings feed into MPLS label-switched paths. It is deployed on HP/Comware routers and switches acting as Label Switch Routers in MPLS networks — the exact use case the HPN-ICF-MPLS-LDP-MIB MIB was built to support.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-MPLS-LDP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP/H3C Comware MPLS-capable routers and switches

Monitoring Examples

An operator polls hpnicfMplsLdpSessionObjects and hpnicfMplsLdpHelloAdjacencyObjects to confirm an LDP session with a peer LSR is operational and hello adjacencies remain active; receipt of a hpnicfMplsLdpSessionDownEventFailure or hpnicfMplsLdpEntityDownEventFailure notification would indicate an LDP session or entity failed to come up, breaking label distribution for the affected MPLS path.

What Can Be Monitored

LDP LSR incarnation parameters
LDP entity/session tables
hello adjacency status
CR-LSP tunnel objects
session up/down failure notifications

Imported Objects

From HPN-ICF-OID-MIB

hpnicfMpls

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TimeInterval
TruthValue

How to Use in IPNetwork Monitor

Example using hpnicfMplsLdpAttemptedSessions OID:

Select a HP/Comware router/switch running MPLS with LDP as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpnicfMplsLdpAttemptedSessions into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports a count of the total attempted sessions for this LDP Entity. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfMplsLdp	1.3.6.1.4.1.11.2.14.11.15.8.12.2			All rights reserved
hpnicfMplsLdpObjects	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1
hpnicfMplsLdpLsrObjects	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1
hpnicfMplsLdpLsrIncarnTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1		not-accessible	MPLS provides support for multiple incarnations of the MPLS Stack in a target. The LSR defined in the standard MIB is treated as an incarnation in this MIB. Using a local policy the Network administrator must group the LDP Entities that should be placed in an incarnation.
hpnicfMplsLdpLsrIncarnEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1		not-accessible	An entry in this table represents an LSR incarnation. All the entries in this table are created initially when the LDP is initiated. The row status of each entry will be in 'notInService' state initially. The row status must be set to 'active' after the necessary configurations are complete with respect to an incarnation. Currenlty the LSR ID of the incarnation is the only mandatory parameter that must be set before the rowStatus is set to 'active'. An LSR Incarnation Entity is uniquely indexed by its Incarnation Identifier.
OID hpnicfMplsLdpLsrID	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.1	MplsLsrIdentifier	read-write	The LSR's Identifier.
T/F hpnicfMplsLdpLsrLoopDetectionPresent	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.2	TruthValue	read-only	A indication of whether this LSR supports loop detection. A value of 'true' indicates this LSR does support loop detection. A value of 'false' indicates this LSR does not support loop detection.
INT hpnicfMplsLdpLsrLoopDetectionAdminStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.3	INTEGER	read-write	To enable loop detection the value of this object should be 'enabled(1)'. Otherwise, to turn off loop detection, set this value to 'disabled(2)'.
INT hpnicfMplsLdpLsrPathVectorLimit	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.4	INTEGER	read-write	This object only has meaning if hpnicfMplsLdpLsrLoopDetectionPresent has the value of 'true'. The value of this object represents the limit of path vectors which this LSR uses to treat the message as if it had traversed a loop.
INT hpnicfMplsLdpLsrHopCountLimit	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.5	INTEGER	read-write	This object only has meaning if hpnicfMplsLdpLsrLoopDetectionPresent has the value of 'true'. The value of this object represents the limit on the Hop Count which this LSR uses to treat the message as if it had traversed a loop.
T/F hpnicfMplsLdpLsrLoopPreventionPresent	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.6	TruthValue	read-only	A indication of whether this LSR supports loop prevention. A value of 'true' indicates this LSR does support loop prevention. A value of 'false' indicates this LSR does not support loop prevention. Current release of MPLS does not provide support to assign this MIB object with a value 'true'.
INT hpnicfMplsLdpLsrLoopPreventionAdminStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.7	INTEGER	read-write	To enable loop prevention the value of this object should be 'enabled(1)'. Otherwise, to turn off loop prevention, set this value to 'disabled(2)'. Current release of MPLS does not provide support to assign this MIB object with a value 'enabled'.
INT hpnicfMplsLdpLsrLabelRetentionMode	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.8	INTEGER	read-write	The LSR can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized label mappings are retained only if they will be used to forward packets, i.e. if label came from a valid next hop. If the value of this object is liberal(2) then all advertized label mappings are retained whether they are from a valid next hop or not. Current release of MPLS does not provide support to assign this MIB object with a value 'liberal'.
INT hpnicfMplsLdpLsrIncarnID	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.9	INTEGER	read-only	The incarnation acts as index to all the elements in this table.
INT hpnicfMplsLdpLsrMaxLdpEntities	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.10	INTEGER	read-write	The maximum number of LDP entities that can be supported by this Incarnation.
INT hpnicfMplsLdpLsrMaxLocalPeers	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.11	INTEGER	read-write	The maximum number of Local LDP peers that can be supported by this Incarnation.
INT hpnicfMplsLdpLsrMaxRemotePeers	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.12	INTEGER	read-write	The maximum number of Remote LDP peers that can be supported by this Incarnation.
INT hpnicfMplsLdpLsrMaxIfaces	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.13	INTEGER	read-write	The maximum number of Label enabled Interfaces that can be supported by this Incarnation.
INT hpnicfMplsLdpLsrMaxLsps	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.14	INTEGER	read-write	The maximum number of Label Switched Paths that can be supported by this Incarnation.
INT hpnicfMplsLdpLsrMaxCrlspTnls	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.15	INTEGER	read-write	The maximum number of CRLSPs that can be supported by this Incarnation.
INT hpnicfMplsLdpLsrMaxErhopPerCrlspTnl	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.16	INTEGER	read-write	The maximum number of ER-Hops that can be supported in a CRLSP tunnel.
ROW hpnicfMplsLdpLsrRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.17	RowStatus	read-create	An object that allows entries in this table to be created and deleted using the RowStatus convention.
INT hpnicfMplsLdpLsrMaxVcmCapability	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.18	INTEGER	read-write
T/F hpnicfMplsLdpLsrVcmPathVecInAllLblMapPresent	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.19	TruthValue	read-write
INT hpnicfMplsLdpLsrRequestRetrytimerValue	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.20	INTEGER	read-write
INT hpnicfMplsLdpLsrNumOfRequestRetryAttempts	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.1.1.1.21	INTEGER	read-write
hpnicfMplsLdpEntityObjects	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2
hpnicfMplsLdpEntityTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1		not-accessible	This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switch Router (LSR).
hpnicfMplsLdpEntityEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1		not-accessible	An entry in this table represents an LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. An LPD Entity is uniquely indexed by its LPD Identifier.
OID hpnicfMplsLdpEntityID	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.1	MplsLdpIdentifier	accessible-for-notify	The LDP identifier which uniquely identifies the LDP Entity. This is s six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific label space within the LSR.
INT hpnicfMplsLdpEntityLabelSpaceType	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.2	INTEGER	read-create	The type of label spaces associated with this LDP Entity. The values are 'unknown(1)' The type of label space is not known. 'perInterface(2)' The type of label space is tied to an interface. 'perPlatform(3)' The type of label space is tied to the platform.
OID hpnicfMplsLdpEntityDefVpi	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.3	AtmVpIdentifier	read-create	The Default VPI value used in the label for the default VPI.
OID hpnicfMplsLdpEntityDefVci	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.4	AtmVcIdentifier	read-create	The Default VCI value used in the label for the default VCI.
OID hpnicfMplsLdpEntityUnlabTrafVpi	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.5	AtmVpIdentifier	read-create	VPI value of the VCC supporting unlabeled traffic.
OID hpnicfMplsLdpEntityUnlabTrafVci	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.6	AtmVcIdentifier	read-create	VCI value of the VCC supporting unlabeled traffic.
INT hpnicfMplsLdpEntityMergeCapability	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.7	INTEGER	read-create	Sets the merge capability for this LDP entity. Current Release of MPLS does not provide support for any kind of Merge.
INT hpnicfMplsLdpEntityVcDirectionality	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.8	INTEGER	read-create	Sets the VC directionality for this LDP entity.
INT hpnicfMplsLdpEntityWellKnownDiscoveryPort	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.9	INTEGER	read-create	The well known LDP Discovery Port.
INT hpnicfMplsLdpEntityMtu	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.10	INTEGER	read-create	The maximum transmission unit (MTU) that was configured for this entity.
INT hpnicfMplsLdpEntityKeepAliveHoldTimer	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.11	INTEGER	read-create	The two octet value which is the proposed keep alive hold timer for this LDP Entity.
INT hpnicfMplsLdpEntityFailedInitSessionThreshold	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.12	INTEGER	read-create	When attempting to establish a session with a given Peer, the given LDP Entity should send out a notification when exceeding this threshold. A value of 0 (zero) for this object indicates that the threshold is infinity. In other words, a notification will not be sent if the value of this object is 0 (zero).
INT hpnicfMplsLdpEntityLabelDistributionMethod	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.13	INTEGER	read-create	For any given LDP session, the method of label distribution must be specified. Current release of MPLS does not provide support for 'downstreamUnsolicited'.
INT hpnicfMplsLdpEntityLabelAllocationMethod	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.14	INTEGER	read-create	For any given LDP session, the method of label allocation must be specified. Label can be allocated in either ordered mode or in the independent mode.
INT hpnicfMplsLdpEntityHelloHoldTimer	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.15	INTEGER	read-create	The two octet value which is the proposed hello hold timer for this LDP Entity.
ROW hpnicfMplsLdpEntityRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.1.1.16	RowStatus	read-create	An object that allows entries in this table to be created and deleted using the RowStatus convention.
hpnicfMplsLdpEntityIfTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.2		not-accessible	This table contains information about the interfaces that are associated with an LDP Entity. There should be atleast one interface associated with each LDP Entity. If the LDP Entity supports 'per interface based label space' label type then, atmost one interface can be associated with the LDP entity. If the LDP Entity supports 'per platform based label space' label type then, more than one interface can be associated with the LDP Entity.
hpnicfMplsLdpEntityIfEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.2.1		not-accessible	An entry in this table represents an Interface that is associated with a LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. An interface (row in this table) can be created/deleted only when the associted LDP Entity row status has the value notInService or notReady.
U32 hpnicfMplsLdpEntityIfIndex	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.2.1.1	Unsigned32	not-accessible	Identifier that uniquely identifies the Interface with respect to an LDP Entity. The ifIndex value corresponds to the IfIndex value of the MIB-II
IP hpnicfMplsLdpEntityIfIpv4Address	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.2.1.2	IpAddress	read-create	The IPv4 address associated with the interface.
ROW hpnicfMplsLdpEntityIfRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.2.1.3	RowStatus	read-create	An object that allows entries in this table to be created and deleted using the RowStatus convention.
hpnicfMplsLdpEntityConfAtmLabelRangeTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.3		not-accessible	The MPLS LDP Entity Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Entities. LDP Entities which use ATM must have at least one entry in this table.
hpnicfMplsLdpEntityConfAtmLabelRangeEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.3.1		not-accessible	A row in the LDP Entity Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. NOTE: The ranges for a specific LDP Entity are UNIQUE and non-overlapping. For example, for a specific LDP Entity index, there could be one entry having ConfLowerBound vpi/vci == 0/32, and ConfUpperBound vpi/vci == 0/100, and a second entry for this same interface with ConfLowerBound vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200. However, there could not be a third entry with ConfLowerBound vpi/vci == 0/200 and ConfUpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e. both entries now have 0/200). A row will not be created unless a unique and non-overlapping range is specified. Thus, row creation implies a one-shot row creation of LDP EntityID and ConfLowerBound vpi/vci and ConfUpperBound vpi/vci. At least one label range entry for a specific LDP Entity MUST include the default VPI/VCI values denoted in the LDP Entity Table.
OID hpnicfMplsLdpEntityConfAtmLabelRangeLowerBoundVPI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.3.1.1	AtmVpIdentifier	not-accessible	The minimum VPI number configured for this range.
OID hpnicfMplsLdpEntityConfAtmLabelRangeLowerBoundVCI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.3.1.2	AtmVcIdentifier	not-accessible	The minimum VCI number configured for this range.
OID hpnicfMplsLdpEntityConfAtmLabelRangeUpperBoundVPI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.3.1.3	AtmVpIdentifier	read-create	The maximum VPI number configured for this range.
OID hpnicfMplsLdpEntityConfAtmLabelRangeUpperBoundVCI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.3.1.4	AtmVcIdentifier	read-create	The maximum VCI number configured for this range.
ROW hpnicfMplsLdpEntityConfAtmLabelRangeRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.3.1.5	RowStatus	read-create	An object that allows entries in this table to be created and deleted using the RowStatus convention.
hpnicfMplsLdpEntityStatsTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.4		not-accessible	This table is a read-only table which augments the MplsLdpConfEntityTable. The purpose of this table is to keep statistical information about the LDP Entities on the LSR.
hpnicfMplsLdpEntityStatsEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.4.1		not-accessible	A row in this table contains statistical information about an LDP Entity.
C32 hpnicfMplsLdpAttemptedSessionsEx	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.2.4.1.1	Counter32	read-only	A count of the total attempted sessions for this LDP Entity.
hpnicfMplsLdpPeerObjects	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3
hpnicfMplsLdpPeerTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1		not-accessible	Information about LDP peers which have been discovered by the LDP Entities that are managed by this agent.
hpnicfMplsLdpPeerEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1		not-accessible	Information about a single Peer.
U32 hpnicfMplsLdpPeerIndex	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.1	Unsigned32	not-accessible	An identifier for the LDP peer that is unique within the scope of this agent.
OID hpnicfMplsLdpPeerID	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.2	MplsLdpIdentifier	read-create	The LDP identifier of this LDP Peer.
ADR hpnicfMplsLdpPeerInternetworkAddrType	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.3	AddressFamilyNumbers	read-create	The type of the internetwork layer address of this LDP peer. This object indicates how the value of hpnicfMplsLdpPeerInternetworkAddr is to be interpreted.
MPL hpnicfMplsLdpPeerInternetworkAddr	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.4	MplsLdpGenAddr	read-create	The value of the internetwork layer address of this LDP peer.
INT hpnicfMplsLdpPeerDefaultMtu	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.5	INTEGER	read-create	The default maximum transmission unit (MTU) of the LDP Peer.
INT hpnicfMplsLdpPeerKeepAliveHoldTimer	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.6	INTEGER	read-create	The two octet unsigned non zero INTEGER that indicates the number of seconds that this Peer proposes for the value of the KeepAlive Interval.
INT hpnicfMplsLdpPeerLabelDistributionMethod	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.7	INTEGER	read-create	For any given LDP session, the method of label distribution must be specified.
INT hpnicfMplsLdpPeerType	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.8	INTEGER	read-create	Indicates whether a peer is a local peer or a remote peer
ROW hpnicfMplsLdpPeerRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.1.1.9	RowStatus	read-create	An object that allows entries in this table to be created and deleted using the RowStatus convention.
hpnicfMplsLdpPeerConfAtmLabelRangeTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.2		not-accessible	The MPLS LDP Peer Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Peers. LDP Peers which use ATM must have at least one entry in this table.
hpnicfMplsLdpPeerConfAtmLabelRangeEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.2.1		not-accessible	A row in the LDP Peer Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. NOTE: The ranges for a specific LDP Peer are UNIQUE and non-overlapping. For example, for a specific LDP Peer index, there could be one entry having ConfLowerBound vpi/vci == 0/32, and ConfUpperBound vpi/vci == 0/100, and a second entry for this same interface with ConfLowerBound vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200. However, there could not be a third entry with ConfLowerBound vpi/vci == 0/200 and ConfUpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e. both entries now have 0/200). A row will not be created unless a unique and non-overlapping range is specified. Thus, row creation implies a one-shot row creation of LDP PeerIndex and ConfLowerBound vpi/vci and ConfUpperBound vpi/vci. At least one label range entry for a specific LDP Peer MUST include the default VPI/VCI values denoted in the LDP Peer Table.
OID hpnicfMplsLdpPeerConfAtmLabelRangeLowerBoundVPI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.2.1.1	AtmVpIdentifier	not-accessible	The minimum VPI number configured for this range.
OID hpnicfMplsLdpPeerConfAtmLabelRangeLowerBoundVCI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.2.1.2	AtmVcIdentifier	not-accessible	The minimum VCI number configured for this range.
OID hpnicfMplsLdpPeerConfAtmLabelRangeUpperBoundVPI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.2.1.3	AtmVpIdentifier	read-only	The maximum VPI number configured for this range.
OID hpnicfMplsLdpPeerConfAtmLabelRangeUpperBoundVCI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.3.2.1.4	AtmVcIdentifier	read-only	The maximum VCI number configured for this range.
hpnicfMplsLdpSessionObjects	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4
hpnicfMplsLdpSessionTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1		not-accessible	A table of Sessions between the LDP Entities and LDP Peers.
hpnicfMplsLdpSessionEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1		not-accessible	An entry in this table represents information on a single session between an LDP Entity and LDP Peer.
U32 hpnicfMplsLdpSessionIndex	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.1	Unsigned32	not-accessible	An unique identifier for this entry such that it identifies a specific LDP Session.
OID hpnicfMplsLdpSessionID	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.2	MplsLdpIdentifier	read-only	The LDP Session identifier.
INT hpnicfMplsLdpSessionProtocolVersion	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.3	INTEGER	read-only	The version of the LDP Protocol which this session is using.
NUM hpnicfMplsLdpSessionKeepAliveHoldTimeRemaining	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.4	TimeInterval	read-only	The keep alive hold time remaining for this session.
INT hpnicfMplsLdpSessionRole	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.5	INTEGER	read-only	An indication of whether the LDP Entity associated with this session is acting in an 'active' role or a 'passive' role.
INT hpnicfMplsLdpSessionState	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.6	INTEGER	read-only	The current state of the session, all of the states 1 - 5 are based on the state machine for session negotiation behavior.
OID hpnicfMplsLdpSessionAtmLabelRangeLowerBoundVPI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.7	AtmVpIdentifier	read-only	The minimum VPI number for this range.
OID hpnicfMplsLdpSessionAtmLabelRangeLowerBoundVCI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.8	AtmVcIdentifier	read-only	The minimum VCI number for this range.
OID hpnicfMplsLdpSessionAtmLabelRangeUpperBoundVPI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.9	AtmVpIdentifier	read-only	The maximum VPI number for this range.
OID hpnicfMplsLdpSessionAtmLabelRangeUpperBoundVCI	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.4.1.1.10	AtmVcIdentifier	read-only	The maximum VCI number for this range.
hpnicfMplsLdpHelloAdjacencyObjects	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.5
hpnicfMplsLdpHelloAdjacencyTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.5.1		not-accessible	A table of Hello Adjacencies for Sessions.
hpnicfMplsLdpHelloAdjacencyEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.5.1.1		not-accessible	Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.
U32 hpnicfMplsLdpHelloAdjacencyIndex	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.5.1.1.1	Unsigned32	not-accessible	An identifier for the adjacency.
NUM hpnicfMplsLdpHelloAdjacencyHoldTimeRemaining	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.5.1.1.2	TimeInterval	read-only	The time remaining for this Hello Adjacency.
hpnicfMplsLdpCrlspTnlObjects	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6
hpnicfMplsLdpCrlspTnlTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1		not-accessible	The hpnicfMplsLdpCrlspTnlTable allows new CRLSP MPLS tunnels to be created. The ER hops associated with a CRLSP tunnel are to be configured using the hpnicfMplsLdpCrlspErHopTable.
hpnicfMplsLdpCrlspTnlEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1		not-accessible	An entry in this table represents an CRLSP MPLS tunnel. An entry can be created by a network administrator.
MPL hpnicfMplsLdpCrlspTnlIndex	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.1	MplsTunnelIndex	accessible-for-notify	Uniquely identifies this row.
STR hpnicfMplsLdpCrlspTnlName	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.2	DisplayString	read-create	The 'canonical' name assigned to the tunnel that can be used to refer to it on the 'console' port.
INT hpnicfMplsLdpCrlspTnlDirection	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.3	INTEGER	read-create	Whether this tunnel is unidirectional-incoming, unidirectional-outgoing, or bidirectional.
INT hpnicfMplsLdpCrlspTnlSignallingProto	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.4	INTEGER	read-create	The signaling protocol, if any, that set up this tunnel.
INT hpnicfMplsLdpCrlspTnlSetupPrio	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.5	INTEGER	read-create	The setup priority of this tunnel.
INT hpnicfMplsLdpCrlspTnlHoldingPrio	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.6	INTEGER	read-create	The holding priority for this tunnel.
BIT hpnicfMplsLdpCrlspTnlPeakDataRate	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.7	BitRate	read-create	The peak rate - the maximum rate at which traffic will be sent on the CRLSP.
BUR hpnicfMplsLdpCrlspTnlPeakBurstSize	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.8	BurstSize	read-create	The peak burst size - the maximum burst size of the traffic that can occur in the established CRLSP.
BIT hpnicfMplsLdpCrlspTnlCommittedDataRate	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.9	BitRate	read-create	The committed rate - the committed rate at which traffic will be sent on the CRLSP.
BUR hpnicfMplsLdpCrlspTnlCommittedBurstSize	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.10	BurstSize	read-create	The committed burst size - the committed burst size of the traffic that will be handled in the established CRLSP.
BUR hpnicfMplsLdpCrlspTnlExcessBurstSize	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.11	BurstSize	read-create	The Excess burst size - the excess burst size limit to be used for traffic conditioning at the ingress of the CRLSP.
T/F hpnicfMplsLdpCrlspTnlIsPinned	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.12	TruthValue	read-create	Indicates whether the loose-routed hops of this tunnel are to be pinned.
INT hpnicfMplsLdpCrlspTnlFrequency	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.13	INTEGER	read-create	Indicates the frequency of usage of the established CRLSP.
INT hpnicfMplsLdpCrlspTnlWeight	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.14	INTEGER	read-create	Indicates the weight that is the established CRLSP.
ROW hpnicfMplsLdpCrlspTnlRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.1.1.15	RowStatus	read-create	For controlling the state of this row. The status can be set to 'active' only when atleast one ERHOP is created in the hpnicfMplsLdpErHopTable, associated with this tunnel.
hpnicfMplsLdpCrlspErHopTable	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.2		not-accessible	The hpnicfMplsLdpCrlspErHopTable is used to indicate the hops, strict or loose, for an MPLS CRLSP tunnel defined in hpnicfMplsLdpCrlspTnlTable. There must be atleast one entry in this table for each CRLSP tunnel that is supported in the hpnicfMplsLdpCrlspTnlTable. The first row in the table is the first hop after the origination point of the tunnel.
hpnicfMplsLdpCrlspErHopEntry	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.2.1		not-accessible	An entry in this table represents a tunnel hop. An entry is created by a network administrator for signalled ERLSP set up by LDP or RSVP.
INT hpnicfMplsLdpCrlspErHopIndex	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.2.1.1	INTEGER	not-accessible	Secondary index into this table identifying the particular hop.
INT hpnicfMplsLdpCrlspErHopAddrType	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.2.1.2	INTEGER	read-create	Address type of this hop.
IP hpnicfMplsLdpCrlspErHopIpv4Addr	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.2.1.3	IpAddress	read-create	If hpnicfMplsLdpCrlspErHopAddrType is ipV4(1), IPv4 address of this hop. This object is not significant otherwise and should return a value of 0.
INT hpnicfMplsLdpCrlspErHopIpv4PrefixLen	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.2.1.4	INTEGER	read-create	If hpnicfMplsLdpCrlspErHopAddrType is ipV4(1), prefix length for this hop's IPv4 address. This object is not significant otherwise and should return a value of 0.
INT hpnicfMplsLdpCrlspErHopStrictOrLoose	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.2.1.5	INTEGER	read-create	Whether this is a strict or loose hop.
ROW hpnicfMplsLdpCrlspErHopRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.12.2.1.6.2.1.6	RowStatus	read-create	For creating, modifying and deleting this row.
hpnicfMplsLdpNotifications	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2
hpnicfMplsLdpNotificationPrefix	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0
NTF hpnicfMplsLdpFailedInitSessionThresholdExceeded	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.1			This notification is generated whenever the value of hpnicfMplsLdpEntityFailedInitSessionThreshold is exceeded.
NTF hpnicfMplsLdpCrlspTunnelUp	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.2			This notification is generated by the Ingress LSR of the CRLSP tunnel on the receipt of Label mapping message from the downstream LSR for the LAbel request sent for the CRLSP tunnel.
NTF hpnicfMplsLdpCrlspTunnelDown	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.3			This notification is generated when a CRLSP Row status is modified to destroy the CRLSP tunnel. - due to pre-emption etc.,
NTF hpnicfMplsLdpCrlspTunnelSetupFailure	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.4			This notification is generated by the Ingress LSR of the CRLSP tunnel on the receipt of Nak message from the downstream LSR for the Label request sent for the CRLSP tunnel. This can occur due to improper ER hop values being set, or Traffic resources not available etc.,
NTF hpnicfMplsLdpIncarnUpEventFailure	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.11			This notification is generated by LDP to notify the Incarnation UP Event failure
NTF hpnicfMplsLdpIncarnDownEventFailure	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.12			This notification is generated by LDP to notify the Incarnation DOWN Event failure
NTF hpnicfMplsLdpEntityUpEventFailure	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.13			This notification is generated by LDP to notify the ENTITY UP Event failure
NTF hpnicfMplsLdpEntityDownEventFailure	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.14			This notification is generated by LDP to notify the ENTITY DOWN Event failure
NTF hpnicfMplsLdpSessionUpEventFailure	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.15			Generation of this trap occurs when the value of 'hpnicfMplsLdpSessionState' enters the 'operational(5)' state.
NTF hpnicfMplsLdpSessionDownEventFailure	1.3.6.1.4.1.11.2.14.11.15.8.12.2.2.0.16			Generation of this trap occurs when the value of 'hpnicfMplsLdpSessionState' leaves the 'operational(5)' state.

RFC description

Manages MPLS Label Distribution Protocol (LDP) sessions, neighbor adjacencies, and label bindings on H3C/HPE devices.

Start monitoring HP/Comware router/switch running MPLS with LDP with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-MPLS-LDP-MIB